WorldWideScience

Sample records for hfc kei kongo

  1. Study of thermodynamic properties of HFC refrigerant mixtures for Loretz-cycled niew generation air-conditioning equipment; Lorentz cycle ka shinsedai kucho kikiyo HFC kei kongo reibai no netsu rikigaku seishitsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, K; Sato, H [Keio University, Tokyo (Japan). Faculty of Science and Technology

    1997-02-01

    This paper describes thermodynamic properties of HFC refrigerant mixtures for Lorentz-cycled new generation air-conditioning equipment. Equipment has been completed for simultaneous measurement of density and vapor-liquid equilibrium property, accurate measurement of latent heat of vaporization, and accurate measurement of specific heat at constant pressure in liquid phase. Final adjustment and preliminary measurements are currently conducted. Through analytical investigation using actually measured data of thermodynamic properties of HFC refrigerant mixtures, five state equations were obtained, i.e., modified Peng-Robinson state equation which can reproduce the vapor-liquid equilibrium property of refrigerant mixtures, modified Patel-Teja state equation, Helmholtz function type state equation which is applicable in the whole fluid region of refrigerant mixtures, and so on. An evaluation test equipment has been fabricated as a trial for Lorentz-cycled air-conditioning equipments using HFC refrigerant mixtures, and demonstration test is conducted to confirm the validity. 9 refs., 5 figs.

  2. FY1995 study of thermodynamic properties of HFC refrigerant mixtures for Lorentz-cycled new generation air-conditioning equipments; 1995 nendo Lorentz cycle ka shinsedai kucho kikiyo HFC kei kongo reibai no netsurikigaku seishitsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A hydrochlorofluorocarbon (HCFC) refrigerant, R-22, is currently being used almost exclusively as a refrigerant for conventional air-conditioning equipments. Since HCFCs are expected to be banned shortly, it is considered a crucial issue to support R and D of the air-conditioning system Lorentz-cycled with hydrofluorocarbon (HFC) refrigerants mixtures. In the present research project, therefore, it is aimed to reveal some of the essential thermodynamic properties of HFC refrigerant mixtures systematically. On the basis of a series of achievements for the last several years by the present research coordinator and his group regarding thermodynamic properties of single-component and blended HFC refrigerants, we have conducted following three major research programs rather systematically on which no challenges have ever been reported worldwide. Throughout a series of experimental as well as analytical researches performed so as to meet the objectives mentioned above, some novel knowledge and valuable outcomes could be obtained in the present study. (1) Precise measurements of vapor-liquid equilibrium properties with simultaneous determination of densities, latent heats of vaporization, and isobaric specific heat capacities in liquid phase. (2) Analytical studies to establish thermodynamic property modeling. (3) Feasibility study of evaluating the Lorentz-cycled performance. (NEDO)

  3. Kei Apple Plant Thorn Synovitis

    African Journals Online (AJOL)

    We noted 2 visible pieces of broken thorn within the joint space (Figure. 1). The pieces were retrieved and upon examination found to be thorns of Kei apple plant .The child was allowed home on the 3rd post operative day on antibiotics for 6 weeks. He has been reviewed 2 weeks post operatively with better range of motion.

  4. Le Kongo de Sony Labou Tansi

    Directory of Open Access Journals (Sweden)

    Céline Gahungu

    2015-02-01

    Full Text Available Les textes inédits de Sony Labou Tansi proposent une réflexion sur l’histoire, et plus singulièrement sur celle du Kongo. Le souvenir du prestigieux royaume apparaît dès les premiers manuscrits, composés au début des années 1970. Loin d’être circonscrit aux écrits de jeunesse, le Kongo surgit sous de multiples formes dans le dédale des textes rédigés au cours des années suivantes. Cette fascination pousse l’écrivain dans une dynamique de recherche esthétique : comment évoquer cet illo tempore mythique sans sacrifier à une historicité convenue ? Comment inventer une écriture en mesure de rendre compte du fabuleux royaume ?L’analyse littéraire ne peut cependant faire fi du contexte politique dans lequel Sony Labou Tansi s’inscrit. Outre sa dimension historique et toponymique, Kongo est un ethnonyme dont l’auteur s’est réclamé. Celui-ci a revendiqué à de nombreuses reprises son appartenance à une identité kongo au point de s’être engagé, à la fin des années 1980, dans les rangs du MCDDI1. Ce discours identitaire et l’adhésion à un parti ethnique ont troublé l’image d’un auteur volontiers perçu comme un démocrate véritable. Est-il possible d’articuler le Kongo littéraire et le Kongo politique ? Le Kongo, dont l’ombre portée apparaît dans les manuscrits littéraires mais également dans les articles et les déclarations politiques, pourrait-il nous aider à saisir les enjeux de l’écriture protéiforme de Sony Labou Tansi ?

  5. Statsdannelse og vann i Kongo

    Directory of Open Access Journals (Sweden)

    Randi Solhjell

    2017-05-01

    Full Text Available Det finnes mye statsvitenskapelig litteratur som karakteriserer den Afrikanske Staten i negative former som svak eller feilet. Kritikere har hevdet at dette er basert på ideer om vestlige normer og idealer for hva en stat skal være. Ut i fra denne kritikken hevder jeg i denne artikkelen at statsdannelse er noe man kan forstå gjennom daglige praksiser i Afrika, som en motvekt til abstrakte og avkuttede modeller for statsdannelse. Slik vil jeg hevde at staten altså ikke er en enhet som utfører «feilede» praksiser, men heller et mangfold av praksiser som utgjør det vi velger å kalle «staten». I denne artikkelen foreslår jeg å se på staten som relasjonelle praksiser, altså mellom mennesker, i områder der staten er en kilde til konflikt. Gjennom å se på et grunnleggende gode som tilgang til vann i en by i øst-Kongo, Bukavu, viser jeg hvordan ideer om staten blir til. Praksisene og forventninger rundt vann fører igjen til et vedvarende og sterkt press mot den faktiske staten.

  6. Global emissions of the hydrofluorocarbons (HFCs) HFC-365mfc, HFC-245fa, HFC-227ea, and HFC-236fa based on atmospheric observations

    Science.gov (United States)

    Vollmer, M. K.; Miller, B. R.; Rigby, M. L.; Reimann, S.; Muhle, J.; Agage, Soge, Snu Members, Kopri Members

    2010-12-01

    We report on the atmospheric measurements and global emissions of the hydrofluorocarbons (HFCs) HFC-365mfc (CH3CH2CF2CF3, 1,1,1,3,3-pentafluorobutane), HFC-245fa (CHF2CH2CF3, 1,1,1,3,3-pentafluoropropane), HFC-227ea (CF3CHFCF3, 1,1,1,2,3,3,3-heptafluoropropane), and HFC-236fa (CF3CH2CF3, 1,1,1,3,3,3-hexafluoropropane). These measurements are from in-situ observations at stations of AGAGE (Advanced Global Atmospheric Gases Experiment) and SOGE (System for Observations of Halogenated Greenhouse Gases in Europe), and from the Korean station Gosan. We also report on flask sample measurements from the Antarctic stations King Sejong and Troll, and extend our records back to the 1970s using archived air samples of both hemispheres. All data are used in a global 12-box 2-dimensional atmospheric transport model to derive global abundances and emission estimates. All four HFCs have strongly increased in the atmosphere in recent years with growth rates at nearly 10 %, resulting in dry air mole fractions at the end of 2009 of 0.49 ppt for HFC-365mfc, 1.00 ppt for HFC-245fa, and 0.51 ppt for HFC-227ea. HFC-236fa, for which we report the first atmospheric measurements, is less abundant and has grown to 0.069 ppt at the end of 2009. Our model results show rapidly growing emissions of HFC-365mfc and HFC-245fa after 2002 but surprisingly these have now started to decline to globally 2.7 kt/yr (HFC-365mfc) and 6.1 kt/yr (HFC-245fa). On the other hand HFC-227ea and HFC-236fa show uninterrupted growth in their emissions of 2.5 kt/yr and 0.2 kt/yr at the end of 2009.

  7. Alfred Kongo, intiimse maalilaadi meister / Juta Kivimäe

    Index Scriptorium Estoniae

    Kivimäe, Juta, 1952-

    2001-01-01

    Alfred Kongost, tema loomingust. A. Kongo 95. sünniaastapäeva tähistav näitus Adamson-Ericu muuseumis 10. X-11. XI ja 9. XI toimub mälestusteõhtu. Näha saab Tiina Pargi 1984. a. filmi A. Kongost

  8. Atmospheric histories and global emissions of the anthropogenic hydrofluorocarbons HFC-365mfc, HFC-245fa, HFC-227ea, and HFC-236fa

    Science.gov (United States)

    Vollmer, Martin K.; Miller, Benjamin R.; Rigby, Matthew; Reimann, Stefan; Mühle, Jens; Krummel, Paul B.; O'Doherty, Simon; Kim, Jooil; Rhee, Tae Siek; Weiss, Ray F.; Fraser, Paul J.; Simmonds, Peter G.; Salameh, Peter K.; Harth, Christina M.; Wang, Ray H. J.; Steele, L. Paul; Young, Dickon; Lunder, Chris R.; Hermansen, Ove; Ivy, Diane; Arnold, Tim; Schmidbauer, Norbert; Kim, Kyung-Ryul; Greally, Brian R.; Hill, Matthias; Leist, Michael; Wenger, Angelina; Prinn, Ronald G.

    2011-04-01

    We report on ground-based atmospheric measurements and emission estimates of the four anthropogenic hydrofluorocarbons (HFCs) HFC-365mfc (CH3CF2CH2CF3, 1,1,1,3,3-pentafluorobutane), HFC-245fa (CHF2CH2CF3, 1,1,1,3,3-pentafluoropropane), HFC-227ea (CF3CHFCF3, 1,1,1,2,3,3,3-heptafluoropropane), and HFC-236fa (CF3CH2CF3, 1,1,1,3,3,3-hexafluoropropane). In situ measurements are from the global monitoring sites of the Advanced Global Atmospheric Gases Experiment (AGAGE), the System for Observations of Halogenated Greenhouse Gases in Europe (SOGE), and Gosan (South Korea). We include the first halocarbon flask sample measurements from the Antarctic research stations King Sejong and Troll. We also present measurements of archived air samples from both hemispheres back to the 1970s. We use a two-dimensional atmospheric transport model to simulate global atmospheric abundances and to estimate global emissions. HFC-365mfc and HFC-245fa first appeared in the atmosphere only ˜1 decade ago; they have grown rapidly to globally averaged dry air mole fractions of 0.53 ppt (in parts per trillion, 10-12) and 1.1 ppt, respectively, by the end of 2010. In contrast, HFC-227ea first appeared in the global atmosphere in the 1980s and has since grown to ˜0.58 ppt. We report the first measurements of HFC-236fa in the atmosphere. This long-lived compound was present in the atmosphere at only 0.074 ppt in 2010. All four substances exhibit yearly growth rates of >8% yr-1 at the end of 2010. We find rapidly increasing emissions for the foam-blowing compounds HFC-365mfc and HFC-245fa starting in ˜2002. After peaking in 2006 (HFC-365mfc: 3.2 kt yr-1, HFC-245fa: 6.5 kt yr-1), emissions began to decline. Our results for these two compounds suggest that recent estimates from long-term projections (to the late 21st century) have strongly overestimated emissions for the early years of the projections (˜2005-2010). Global HFC-227ea and HFC-236fa emissions have grown to average values of 2.4 kt yr-1

  9. Isothermal phase equilibria for the (HFC-32 + HFC-134a) mixed-gas hydrate system

    International Nuclear Information System (INIS)

    Miyauchi, Hiroshi; Yasuda, Kenjiro; Matsumoto, Yuuki; Hashimoto, Shunsuke; Sugahara, Takeshi; Ohgaki, Kazunari

    2012-01-01

    Highlights: ► Structural phase transition results in the heterogeneous azeotropic-like behaviour. ► HFC-134a molecules, in spite of an s-II former, occupy the large cages of s-I. ► Negative azeotropic-like behaviour becomes more remarkable at higher temperatures. - Abstract: Isothermal phase equilibria (pressure-composition relations in hydrate, gas, and aqueous phases) in the {difluoromethane (HFC-32) + 1,1,1,2-tetrafluoroethane (HFC-134a)} mixed-gas hydrate system were measured at the temperatures 274.15 K, 279.15 K, and 283.15 K. The heterogeneous azeotropic-like behaviour derived from the structural phase transition of (HFC-32 + HFC-134a) mixed-gas hydrates appears over the whole temperature range of the present study. In addition to the heterogeneous azeotropic-like behaviour, the isothermal phase equilibrium curves of the (HFC-32 + HFC-134a) mixed-gas hydrate system exhibit the negative homogeneous azeotropic-like behaviour at temperatures 279.15 K and 283.15 K. The negative azeotropic-like behaviour, which becomes more remarkable at higher temperatures, results in the lower equilibrium pressure of (HFC-32 + HFC-134a) mixed-gas hydrates than those of both simple HFC-32 and HFC-134a hydrates. Although the HFC-134a molecule forms the simple structure-II hydrate at the temperatures, the present findings reveal that HFC-134a molecules occupy a part of the large cages of the structure-I mixed-gas hydrate.

  10. THERMODYNAMIC PROPERTIES OF SELECTED HFC REFRIGERANTS

    Science.gov (United States)

    Hydrofluorocarbon (HFC) refrigerants are possible alternatives to replace ozone-depleting chlorofluorocarbon and hydrochlorofluorocarbon (HCFC) refrigerants. The flammability of a proposed new refrigerant is a major consideration in assessing its utility for a particular applicat...

  11. Kei Apple Plant Thorn Synovitis | Nyamohanga | Annals of African ...

    African Journals Online (AJOL)

    It can present as a diagnostic difficulty because of its insidious onset after an apparently trivial injury, which may not be reported. Historically, thorn synovitis has been considered aseptic and treated with removal of the intra-articular foreign body and the affected synovial ring. We present a child with Kei apple thorn that had ...

  12. CFC and HFC recycling equipments: Test performances

    International Nuclear Information System (INIS)

    Picini, P.; Caropreso, G.; Cicoli, G.; Posarelli, M.

    1996-12-01

    Actual regulatory conditions about ozone layer depleting chemicals set problems on their disposal and on the management of plants still using illegal CFCs. Anyway fluids that will replace CFCs (i.e. HFCs) will not be allowed to be spread into the atmosphere, due to their high costs and to the greenhouse effect. A viable solution would be the recovery, purification and recycle of contaminated fluids. ENEA (National Agency for New Technology, Energy and the Environment), in cooperation with ICF (Industria Componenti Frigoriferi) Company leader in the field of air refrigerating and conditioning, patented a device able to extract, to clean and to recycle CFC 12 and HFC 134a in the refrigerating systems. This paper presents experimental data from the qualification tests on a device performing the above mentioned operations regarding systems that use HFC 134a as process fluid

  13. High-aspect-ratio HfC nanobelts accompanied by HfC nanowires: Synthesis, characterization and field emission properties

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Song, E-mail: tiansong22@126.com [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China); School of Materials Science and Engineering, Chongqing Jiaotong University, Chongqing 400074 (China); Zhang, Yulei; Ren, Jincui; Qiang, Xinfa; Zhang, Shouyang [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China); Li, Hejun, E-mail: lihejun@nwpu.edu.cn [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China)

    2017-04-30

    Highlights: • HfC naobelts accompanied by HfC nanowires were synthesized by a catalytic CVD method. • HfC nanobelts as a novel structure of HfC ceramic are reported for the first time. • HfC nanobelts have 100–200 μm in lengths and reach up to 10 μm in widths. • The synthesized product is promising field nanoemitters. - Abstract: As a key refractory carbide, hafnium carbide (HfC) is commonly used as structural materials while the field emission (FE) application of HfC in the field of vacuum microelectronics is almost the only one for functional material purposes. Based on its outstanding physical and chemical characteristics, HfC is identified as a potential candidate with satisfactory mechanical properties and long-term and/or high-temperature FE stability for future applications in high-performance field emitters. However, the development of HfC in various FE applications is hindered because it is not facile to fabricate large-scale low-dimensional HfC field nanoemitters. Herein, High-aspect-ratio HfC nanobelts accompanied by HfC nanowires were synthesized on a large scale by a traditional and simple catalytic chemical vapor deposition (CVD) method. Classical vapor–liquid–solid (VLS) theory was employed to explain the growth of the HfC nanowires and nanobelts along axial direction. The thin HfO{sub 2} shell and thin C layer surrounding the nanostructures might give rise to the diameter fluctuation of HfC nanowires and the width increase of HfC nanobelts in lateral direction. Field emission results show that the high-aspect-ratio HfC nanobelts accompanied by the nanowires are promising field nanoemitters, which exhibit excellent field emission properties with a fairly low turn-on field of ∼1.5 V μm{sup −1} and a low current fluctuation less than ∼10%. This suggests that HfC ceramics with high-aspect-ratio nanostructures are ideal cathode material for various field emission applications.

  14. The Support of MPA (Marine Protected Area) in Coral Triangle Area: Evidence from Kei Islands, Indonesia

    Science.gov (United States)

    Hamid, Syahibul K.; Teniwut, Wellem A.; Teniwut, Roberto M. K.; Rahantoknam, Meyske A.; Hasyim, Cawalinya L.; Hungan, Marselus

    2017-10-01

    Kei Islands located inside the coral triangle. Therefore, the biodiversity level on the sea in this area is considered high. United nation has proposed for water that included in the coral triangle has to apply marine protected area (MPA) to preserve the area. The main problem is most of the community especially in Kei Islands have depended on the sea as their sources of the economy even fisheries commodity like fish play a large part on the inflation rate and other prosperity indicators likes school and housing. Also, Kei Islands practice on form local wisdom for owning areal of the sea which calls “petuanan laut” by certain of villages or group of villages in one area. This study aimed to map the cluster of catching fisheries area based on the quantity of fish supply on a local market in Kei Islands and measure each cluster on their support and perspective on Marine Protected Area (MPA). We conducted a focus group discussion and collecting additional data by questionnaires with descriptive and quantitative analysis with logistic regression. The implication of this study can provide a clear view of coastal communities view on MPA program also to identify an area that has marine resources, human resources, and equipment to provide government an empirical view on catching fisheries in Kei Islands to issued better policy to develop fishing industry in Kei Islands.

  15. Neue Phoriden aus Belgisch-Kongo, gesammelt von Dr. Jos. Bequaert

    NARCIS (Netherlands)

    Schmitz, H.

    1916-01-01

    Durch die Güte des Herrn Dr. Jos. Bequaert konnte ich einige Phoriden untersuchen, die dieser eifrige Entomologe während seines letzten Aufenthalts am Kongo und im Ruwenzori-Gebirge gesammelt hat. Es lagen im ganzen 5 Arten vor, darunter zwei neue, die im folgenden beschrieben werden. Von den drei

  16. 78 FR 41972 - Culturally Significant Objects Imported for Exhibition Determinations: “Kongo Across the Waters”

    Science.gov (United States)

    2013-07-12

    ... the exhibition ``Kongo across the Waters,'' imported from abroad for temporary exhibition within the... objects at the Samuel P. Harn Museum of Art, Gainesville, Florida, from on or about October 22, 2013, until on or about March 23, 2014, the Jimmy Carter Presidential Library and Museum, Atlanta, Georgia...

  17. Polyphenol composition and antioxidant activity of Kei-apple (Dovyalis caffra) juice.

    Science.gov (United States)

    Loots, Du Toit; van der Westhuizen, Francois H; Jerling, Johann

    2006-02-22

    The polyphenolic and ascorbate (ASC) components as well as the antioxidant capacity of Kei-apple (Dovyalis caffra) juice were analyzed and compared to three other fruit juices. The Kei-apple juice had significantly the highest total polyphenolic concentrations (1013 mg gallic acid equivalent/L), and solid phase (C(18)) fractionation identified the majority of these polyphenols to be phenolic acids. The Kei-apple juice also had significantly the highest ASC concentrations (658 mg/L), which showed exceptional heat stability with very little conversion to dehydroascorbate (DHA). Antioxidant capacities of both the unfractionated fruit juices and their solid phase-extracted fractions, as determined by oxygen radical absorbance capacity and ferric reducing antioxidant power analyses, correlated well to the polyphenol concentrations. Gas chromatography-mass spectrometry analyses showed caffeic acid as the most abundant polyphenol present (128.7 mg/L) in the Kei-apple juice; it contributed to 63% of the total antioxidant capacity (of all of the individual compounds identified). Other notable polyphenols identified in higher concentrations included p-coumaric acid, p-hydroxyphenylacetic acid, and protocatechuic acid. Our results therefore support the putative high antioxidant value linked to this fruit and better define this potential in terms of the major antioxidants that exist in the Kei-apple.

  18. Transmission design in a multimode HFC network

    Science.gov (United States)

    Cambron, G. Keith

    1996-11-01

    Contemporary hybrid fiber coaxial (HFC) networks are capable of supporting a wide range of services including traditional analog video, telephony, digital video, and data services. Each service has unique performance or service requirements. This contribution examines transmission design for one such network. Pacific Bell's advanced communications network (ACN). The design methodology begins with a set of end to end service quality objectives. Network impairments, such as noise, distortion and delay, are allocated across the network elements using a set of standard network models. These models are a representative set of the actual field designs and bound the network operating parameters. Network components, headend equipment, and customer premises equipment are specified analytically or characterized empirically in relationship to the chosen impairment set. The component parameters are then included in analytical models to estimate overall network performance. In addition to the forward path transmission considerations examined by traditional coaxial network designers, other dimensions including power consumption, traffic demand, and message latency are taken into account. Analytical models are used to estimate the effects of multiple modulation schemes within the unified network. The variability introduced by on demand services such as telephony and interactive digital services changes the base computational domain from deterministic models to stochastic ones. These models are then used to set operating parameters at measurable points throughout the network for proof of performance prior to turn up, and for ongoing performance monitoring. For closure, empirical results are compared with model projections as a way of verifying and improving the predictive models.

  19. Prendas-Ngangas-Enquisos: turbulence and the influence of the dead in Cuban-Kongo material culture.

    Science.gov (United States)

    Ochoa, Todd Ramón

    2010-01-01

    Cuban-Kongo praise of the dead in Havana turns insistently around complex agglomerations of materials called "prendas,"ngangas," and "enquisos." This article addresses the ontological status of "prendas-ngangas-enquisos," which practitioners of Cuban-Kongo affliction practices care for as entities that determine the very possibility of their healing and harming craft. Cuban-Kongo societies of affliction, in Havana collectively referred to as "Palo," stake their claim to influence others in and through these entities. In this essay I seek to position the influence generated in prendas-ngangas-enquisos as a problem for Euro-American materialism, to be addressed not through symbolic or representational solutions but, rather, by refocusing the problem itself via alternate distributions of its epistemological, historical, and ethnographic elements. Contextualized within ethnographic description, I first propose that prendas-ngangas-enquisos do not conform to dialectical logic, and should thus be positioned conceptually as something other than "objects" or "fetishes." From there, I consider Creole turns on the term prenda and explore scholarly accounts of 19th-century Cuban slavery and manumission, which I place alongside what is known about pawn slavery among BaKongo people prior to and during the Atlantic slave trade. Having established a basic series of conceptual and historiographic coordinates, I then suggest ethnographically how prendas-ngangas-enquisos come to command others, thereby guaranteeing Cuban-Kongo healing and harming sovereignty in Cuba today.

  20. Water plasma generation under atmospheric pressure for HFC destruction

    International Nuclear Information System (INIS)

    Watanabe, Takayuki; Tsuru, Taira

    2008-01-01

    The purpose of this paper is to investigate the decomposition process of hydrofluoroethylene (HFC-134a) by water plasmas. The water plasma was generated by DC arc discharge with a cathode of hafnium embedded into a copper rod and a nozzle-type copper anode. The advantage of the water plasma torch is the generation of 100%-water plasma by DC discharge. The distinctive steam generation leads to the portable light-weight plasma generation system that does not require the gas supply unit, as well as the high energy efficiency owing to the nonnecessity of the additional water-cooling. HFC-134a was injected into the water plasma jet to decompose it in the reaction tube. Neutralization vessel was combined to the reaction tube to absorb F 2 and HF generated from the HFC-134a decomposition. The decomposition was performed with changing the feed rate of HFC-134a up to 185 mmol/min. The decomposition efficiency of 99.9% can be obtained up to 0.43 mmol/kJ of the ratio of HFC-134a feed rate to the arc power, hence the maximum feed rate was estimated to be 160 g/h at 1 kW of the arc power

  1. Two-phase flow characteristics of HFC and HCFC fluid

    International Nuclear Information System (INIS)

    Ueno, T.; Matsuda, K.; Kusakabe, T.

    1998-01-01

    Some two-phase flow characteristics of HFC and HCFC fluid have been investigated experimentally. Fluids used in this experiment are HCFC22 (hereinafter called 'R22'), HCFC123 (hereinafter called 'R123') and Mixture of HFC fluid (hereinafter called 'R407C'). The fluid R407C are mixture of HFC32, HFC134a and HFC125, and their concentrations are 23wt%, 52wt% and 25wt%, respectively. This paper presents main flow parameters such as void fraction, interfacial velocities, bubble diameter distribution and pressure drop multiplier, which can characterize flow behavior. The void fractions and interfacial velocities were measured at some local positions in the single pipe using the bi-optical probe(hereinafter called 'BOP'). The procedure to calculate the void fraction from the void signals obtained by BOP were adopted the so-called slice method. The effects of slice levels on the void fraction were discussed taking into account bubble diameter. The new correlation of slice level as the function of void fraction has been proposed. The area-averaged void fractions obtained from BOP's void signals using new correlation were compared with void fractions obtained from pressure drops. The area-averaged interfacial velocities were also compared with the superficial gas velocities. It was concluded that the accuracy of BOP measurements are 5% for void fraction and less than 8.5% for interfacial velocity

  2. The development of sasi laut in the preservation of sea in Kei community

    Science.gov (United States)

    Ananingsih, Sri Wahyu

    2018-02-01

    "Sasi laut" is a local wisdom of Kei society that prohibits community members to take natural resources in a particular area over a period of time. Sasi laut has an important role in the preservation of the sea. This article is based on research. The purpose of the research is to analyze causal factors of sasi laut are not practiced anymore in Kei kecil society, and the efforts to revitalize sasi laut as a local wisdom to preserve sea. This article uses socio-legal approach and the analysis is qualitative. The data consist of primary and secondary data. The results of the research show that sasi laut in several villages of Kei kecil is not practiced anymore because of the damage to sea and ecosystem, market problem, the society problem and adat institution problem. The efforts to revitalize sasi laut are improve the quality of the sea environment, legal awareness Kei society and the participation of local government. This article can be a recommendation for the local government of Southeast Maluku in order to determine the policy of sasi laut.

  3. Schizosaccharomyces pombe and Saccharomyces cerevisiae yeasts in sequential fermentations: Effect on phenolic acids of fermented Kei-apple (Dovyalis caffra L.) juice.

    Science.gov (United States)

    Minnaar, P P; Jolly, N P; Paulsen, V; Du Plessis, H W; Van Der Rijst, M

    2017-09-18

    Kei-apple (Dovyalis caffra) is an evergreen tree indigenous to Southern Africa. The fruit contains high concentrations of l-malic acid, ascorbic acid, and phenolic acids. Kei-apple juice was sequentially inoculated with Schizosaccharomyces pombe and Saccharomyces cerevisiae yeasts. A reference fermentation using only S. cerevisiae was included. The fermentation was monitored by recording mass loss. At the end of fermentation, twelve untrained judges conducted free choice aroma profiling on the fruit wines. The Kei-apple juice and wines were analysed for total titratable acidity, total soluble solids, pH, alcohol, l-malic acid, and phenolic acids. Total titratable acidity was ca. 70% lower in Kei-apple wines produced with S. pombe+S. cerevisiae than in Kei-apple juice. Kei-apple wines produced with S. pombe+S. cerevisiae showed substantially lower concentrations of l-malic acid than Kei-apple wines produced with S. cerevisiae only. Wines produced with S. cerevisiae only proved higher in phenolic acid concentrations than wines produced with S. pombe+S. cerevisiae. Chlorogenic acid was the most abundant phenolic acid measured in the Kei-apple wines, followed by protocatechuic acid. Judges described the Kei-apple wines produced with S. pombe+S. cerevisiae as having noticeable off-odours, while wines produced with S. cerevisiae were described as fresh and fruity. Kei-apple wines (S. pombe+S. cerevisiae and S. cerevisiae) were of comparable vegetative and organic character. Saccharomyces cerevisiae produced Kei-apple wine with increased caffeic, chlorogenic, protocatechuic, and sinapic acids, whereas S. pombe+S. cerevisiae produced Kei-apple wines with increased ferulic, and p-coumaric acids and low l-malic acid. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Ruumi kohta arvamuse avaldamiseks ei pea olema arhitekt / Katrin Koov, Ave Kongo ; intervjueerinud Merle Karro-Kalberg

    Index Scriptorium Estoniae

    Koov, Katrin, 1973-

    2016-01-01

    Erahuvikoolina tegutseva arhitektuurikooli eestvedamisel töötatakse välja ruumiõppe valikainemoodulit gümnaasiumile. Ruumiõppest räägivad arhitektide liidu president, arhitektuurikooli õpetaja Katrin Koov ja Saue gümnaasiumi kunstiõpetaja Ave Kongo

  5. Yellow Fever Outbreak - Kongo Central Province, Democratic Republic of the Congo, August 2016.

    Science.gov (United States)

    Otshudiema, John O; Ndakala, Nestor G; Mawanda, Elande-Taty K; Tshapenda, Gaston P; Kimfuta, Jacques M; Nsibu, Loupy-Régence N; Gueye, Abdou S; Dee, Jacob; Philen, Rossanne M; Giese, Coralie; Murrill, Christopher S; Arthur, Ray R; Kebela, Benoit I

    2017-03-31

    On April 23, 2016, the Democratic Republic of the Congo's (DRC's) Ministry of Health declared a yellow fever outbreak. As of May 24, 2016, approximately 90% of suspected yellow fever cases (n = 459) and deaths (45) were reported in a single province, Kongo Central Province, that borders Angola, where a large yellow fever outbreak had begun in December 2015. Two yellow fever mass vaccination campaigns were conducted in Kongo Central Province during May 25-June 7, 2016 and August 17-28, 2016. In June 2016, the DRC Ministry of Health requested assistance from CDC to control the outbreak. As of August 18, 2016, a total of 410 suspected yellow fever cases and 42 deaths were reported in Kongo Central Province. Thirty seven of the 393 specimens tested in the laboratory were confirmed as positive for yellow fever virus (local outbreak threshold is one laboratory-confirmed case of yellow fever). Although not well-documented for this outbreak, malaria, viral hepatitis, and typhoid fever are common differential diagnoses among suspected yellow fever cases in this region. Other possible diagnoses include Zika, West Nile, or dengue viruses; however, no laboratory-confirmed cases of these viruses were reported. Thirty five of the 37 cases of yellow fever were imported from Angola. Two-thirds of confirmed cases occurred in persons who crossed the DRC-Angola border at one market city on the DRC side, where ≤40,000 travelers cross the border each week on market day. Strategies to improve coordination between health surveillance and cross-border trade activities at land borders and to enhance laboratory and case-based surveillance and health border screening capacity are needed to prevent and control future yellow fever outbreaks.

  6. Potential Demand of Relatively New and Emerging Marine Ecotourism in Kei Islands

    Science.gov (United States)

    Dewa Ayu Raka Susanti, Ida I.; Teniwut, Wellem A.; Kahfi, Syahibul; M. K Teniwut, Roberto; Picaulima, Simon; Hungan, Marselus; Rahantoknam, Meyske; Hasyim, Cawalinya; Rahakbauw, Siska D.; Renjaan, M. R.; Ngabalin, Anna M.; Ngangun, Tati A.; Pentury, Frischila; Betaubun, Kamilius D.; Ngamel, A. K.; Ohoiwutun, Elisabeth C.

    2017-10-01

    One of the main resources for the economic development of coastal are marine ecotourism. Although for developing country such as Indonesia and especially for an area that located far from a big city like Kei Islands in Maluku, development of marine ecotourism might face a greater challenge than any other places. Considering the potential for multiplier effect on economic of a coastal community, the purpose of this research was to analyze and measure the economic value of new, raw and emerging marine ecotourism spot and determine the demand based on domestic tourist perspective. We pick five new and emerging marine ecotourism spots in this area as case study and used purposive sampling technique to target potential domestic tourist who have visited those five marine ecotourism spots and measure their preference and measure their demand potential by used willingness to revisit (WTR) and logistic regression for analyze the data, this research conducted in Kei Islands, Indonesia. This result can provide broad and comprehensive perspective on developing marine ecotourism in a mildly isolated coastal area like Kei Islands and place similar.

  7. Evaporation of refrigerant HFC 407C on plain tubes or at an improved surface; Evaporation du refrigerant HFC 407C sur des tubes lisses ou a surface amelioree

    Energy Technology Data Exchange (ETDEWEB)

    Zuercher, O.; Favrat, D.; Thome, J. R.; Kattan, N.; Nidegger, E. [Ecole polytechnique federale, Lab. d` energetique industrielle, Lausanne (Switzerland)

    1996-11-15

    The substitution of CFC refrigerants in refrigeration systems, heat pumps and organic Rankine cycles for heat recovery, requires good methods for predicting heat transfer of substitute fluids. The measurements in the LENI test facility (concentric tubes with water flowing in a counter-current flow) with HFC 407C, HFC 134a, HCFC 123, HFC 404a and HFC/HCFC 402A provide a new data bank for new refrigerants, and allow a coherent comparison with old refrigerants CFC 11, CFC 12, CFC/HCFC 502 and with existing correlations. The existing correlations were found to be inadequate. Because of this work, an improved flow pattern map and flow boiling model were developed, which resulted in a substantial progress in the accurate predict of heat transfer in plain, horizontal tubes for refrigerants without oil. The Kattan et al. correlation was programmed to calculate and compare predicted heat transfer coefficients to the new HFC 407C test data. The flow pattern map proposed by Kattan et al. was also programmed and compared to flow regimes observed for HFC 407C. It predicted the HFC 407C flow pattern data quite accurately. The original objective of the HFC 407C measurements was the validation of the Kattan et al. correlation applied to a zeotropic refrigerant blend. Local flow boiling heat transfer coefficients were measured for HFC 407C evaporating inside a microfin and a plain tube. In addition, microfin heat transfer augmentation relative to a plain tube was investigated. The presence of oil in the evaporator had a complex effect on heat transfer coefficients. Local flow boiling heat transfer coefficients were measured for refrigerant HFC 407C ester oil mixtures (Mobil EAL Arctic 68). A new thermodynamic approach for modeling mixtures of zeotropic refrigerant blends and lubricating oils was also developed. (author) figs., tabs., 14 refs.

  8. Hydrofluorocarbon (HFC) Scenarios, Climate Effects and the Montreal Protocol

    Science.gov (United States)

    Velders, G. J. M.; Fahey, D. W.; Daniel, J. S.

    2016-12-01

    The Montreal Protocol has reduced the use of ozone-depleting substances by more than 95% from its peak levels in the 1980s. As a direct result the use of hydrofluorocarbons (HFCs) as substitute compounds has increased significantly. National regulations to limit HFC use have been adopted recently in the European Union, Japan and USA, and four proposals have been submitted to amend the Montreal Protocol to substantially reduce growth in HFC use. The Parties of the Montreal Protocol have discussed these proposals during their meetings in 2016. The effects of the national regulations and Montreal Protocol amendment proposals on climate forcings and surface temperatures will be presented. Global scenarios of HFC emissions reach 4.0-5.3 GtCO2-eq yr-1 in 2050, which corresponds to a projected growth from 2015 to 2050 which is 9% to 29% of that for CO2 over the same time period. In 2050, in percent of global HFC emissions, China ( 30%), India and the rest of Asia ( 25%), Middle East and northern Africa ( 10%), and USA ( 10%) are the principal source regions; and refrigeration and stationary air conditioning are the major use sectors. Calculated baseline emissions are reduced by 90% in 2050 by implementing the North America Montreal Protocol amendment proposal. This corresponds to a reduction in surface temperature attributed to HFCs from 0.1 oC to 0.04 oC in 2050 and from 0.3-0.4 oC to 0.02 oC in 2100.

  9. HFC-134A and HCFC-22 supermarket refrigeration demonstration and laboratory testing. Phase I. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    Aspen Systems and a team of nineteen agencies and industry participants conducted a series of tests to determine the performance of HFC-134a, HCFC-22, and CFC-502 for supermarket application. This effort constitutes the first phase of a larger project aimed at carrying out both laboratory and demonstration tests of the most viable HFC refrigerants and the refrigerants they replace. The results of the Phase I effort are presented in the present report. The second phase of the project has also been completed. It centered on testing all viable HFC replacement refrigerants for CFC-502. These were HFC-507, HFC-404A, and HFC-407A. The latter results are published in the Phase II report for this project. As part of Phase I, a refrigeration rack utilizing a horizontal open drive screw compressor was constructed in our laboratory. This refrigeration rack is a duplicate of one we have installed in a supermarket in Clifton Park, NY.

  10. Rate constants for the reactions of OH with HFC-134a (CF3CH2F) and HFC-134 (CHF2CHF2)

    Science.gov (United States)

    Demore, W. B.

    1993-01-01

    Measurements of rate constants for HFC-134 (CF2HCF2H) relative to CH3CCl3, HFC-125, and HFC-134a are reported. The measurements were made in a slow-flow, temperature controlled photochemical reactor, and were based on relative rates of disappearance of the parent compounds as measured by FTIR spectroscopy. Hydroxyl radicals were generated by 254-nm photolysis of O3 in the presence of water vapor. NASA/JPL rate constants for the reference compounds are used to derive temperature-dependent rate constants of both compounds. Rate constants obtained from the different reference compounds are in excellent agreement. The presently recommended rate constant for HFC-134a is about 25 percent too high.

  11. Liquid-air partition coefficients of 1,1-difluoroethane (HFC152a), 1,1,1-trifluoroethane (HFC143a), 1,1,1,2-tetrafluoroethane (HFC134a), 1,1,1,2,2-pentafluoroethane (HFC125) and 1,1,1,3,3-pentafluoropropane (HFC245fa).

    Science.gov (United States)

    Ernstgård, Lena; Lind, Birger; Andersen, Melvin E; Johanson, Gunnar

    2010-01-01

    Blood-air and tissue-blood coefficients (lambda) are essential to characterize the uptake and disposition of volatile substances, e.g. by physiologically based pharmacokinetic (PBPK) modelling. Highly volatile chemicals, including many hydrofluorocarbons (HFC) have low solubility in liquid media. These characteristics pose challenges for determining lambda values. A modified head-space vial equilibrium method was used to determine lambda values for five widely used HFCs. The method is based on automated head-space gas chromatography and injection of equal amount of chemical in two head-space vials with identical air phase volumes but different volumes of the liquid phase. The liquids used were water (physiological saline), fresh human blood, and olive oil. The average lambda values (n = 8) were as follows: 1,1-difluoroethane (HFC152a) - 1.08 (blood-air), 1.11 (water-air) and 5.6 (oil-air); 1,1,1-trifluoroethane (HFC143a) - 0.15, 0.15 and 1.90; 1,1,1,2-tetrafluoroethane (HFC134a) - 0.36, 0.35 and 3.5; 1,1,1,2,2-pentafluoroethane (HFC125) - 0.083, 0.074 and 1.71; and 1,1,1,3,3-pentafluoropropane (HFC245fa) - 0.62, 0.58 and 12.1. The lambda values appeared to be concentration-independent in the investigated range (2-200 ppm). In spite of the low lambda values, the method errors were modest, with coefficients of variation of 9, 11 and 10% for water, blood and oil, respectively.

  12. Phytochemicals and nutritional composition in accessions of Kei-apple (Dovyalis caffra): Southern African indigenous fruit.

    Science.gov (United States)

    Mpai, Semkaleng; du Preez, Rosemary; Sultanbawa, Yasmina; Sivakumar, Dharini

    2018-07-01

    Current study was initiated to identify the phytochemicals and the nutritional profile of eleven Kei-apple fruit accessions. Accession FH29 showed the highest level (492.45 mg 100 g -1 fresh weight) of total phenolic content, higher than the referral fruit, blueberry. Pyrogallol was identified as the predominant phenolic compound in all accessions. Accession FH 29 showed the highest (49.75 µmol TEAC g -1 fresh weight) antioxidant capacity. Catechin content was higher in accessions; FH151, FH15, FH14, FH29, FH243, FH 239 and FH 231. Accessions, FH14 and FH232 exhibited higher levels of β-carotene than the referral fruit apples (cv. Top red) and peaches (cv. Excellence). The total sugar (glucose and fructose) was highest (50 mg g -1 fresh weight) in accession FH240. Asparagine (3122.18 mg L -1 ) and gamma-aminobutyric (1688.87 mg L -1 ) were higher in accessions FH239 and FH243 respectively. Overall, the accession Kei-apple FH236 can be regarded as a good source of essential amino acids. Copyright © 2018 Elsevier Ltd. All rights reserved.

  13. HfC plasma coating of C/C composites

    International Nuclear Information System (INIS)

    Boncoeur, M.; Schnedecker, G.; Lulewicz, J.D.

    1992-01-01

    The surface properties of C/C composites such as hardness and corrosion or erosion resistance can be modified by a ceramic coating applied by plasma torch. The technique of plasma spraying in controlled temperature and atmosphere, that was developed and patented by the CEA, makes it possible to apply coatings to the majority of metals and ceramics without affecting the characteristics of the composite. An example of hard deposit of HfC on a C/C composite is described. The characteristics of the deposit and of the bonding with the C/C composite were studied before and after a heat treatment under vacuum for 2 hours at 1000 C. 2 refs

  14. Experimental study of hydrocarbon mixtures to replace HFC-134a in a domestic refrigerator

    International Nuclear Information System (INIS)

    Wongwises, Somchai; Chimres, Nares

    2005-01-01

    This work presents an experimental study on the application of hydrocarbon mixtures to replace HFC-134a in a domestic refrigerator. The hydrocarbons investigated are propane (R290), butane (R600) and isobutane (R600a). A refrigerator designed to work with HFC-134a with a gross capacity of 239 l is used in the experiment. The consumed energy, compressor power and refrigerant temperature and pressure at the inlet and outlet of the compressor are recorded and analysed as well as the distributions of temperature at various positions in the refrigerator. The refrigerant mixtures used are divided into three groups: the mixture of three hydrocarbons, the mixture of two hydrocarbons and the mixture of two hydrocarbons and HFC-134a. The experiments are conducted with the refrigerants under the same no load condition at a surrounding temperature of 25 deg. C. The results show that propane/butane 60%/40% is the most appropriate alternative refrigerant to HFC-134a

  15. HFC-23 (CHF3 emission trend response to HCFC-22 (CHClF2 production and recent HFC-23 emission abatement measures

    Directory of Open Access Journals (Sweden)

    R. G. Prinn

    2010-08-01

    Full Text Available HFC-23 (also known as CHF3, fluoroform or trifluoromethane is a potent greenhouse gas (GHG, with a global warming potential (GWP of 14 800 for a 100-year time horizon. It is an unavoidable by-product of HCFC-22 (CHClF2, chlorodifluoromethane production. HCFC-22, an ozone depleting substance (ODS, is used extensively in commercial refrigeration and air conditioning, in the extruded polystyrene (XPS foam industries (dispersive applications and also as a feedstock in fluoropolymer manufacture (a non-dispersive use. Aside from small markets in specialty uses, HFC-23 has historically been considered a waste gas that was, and often still is, simply vented to the atmosphere. Efforts have been made in the past two decades to reduce HFC-23 emissions, including destruction (incineration in facilities in developing countries under the United Nations Framework Convention on Climate Change's (UNFCCC Clean Development Mechanism (CDM, and by process optimization and/or voluntary incineration by most producers in developed countries. We present observations of lower-tropospheric mole fractions of HFC-23 measured by "Medusa" GC/MSD instruments from ambient air sampled in situ at the Advanced Global Atmospheric Gases Experiment (AGAGE network of five remote sites (2007–2009 and in Cape Grim air archive (CGAA samples (1978–2009 from Tasmania, Australia. These observations are used with the AGAGE 2-D atmospheric 12-box model and an inverse method to produce model mole fractions and a "top-down" HFC-23 emission history. The model 2009 annual mean global lower-tropospheric background abundance is 22.6 (±0.2 pmol mol−1. The derived HFC-23 emissions show a "plateau" during 1997–2003, followed by a rapid ~50% increase to a peak of 15.0 (+1.3/−1.2 Gg/yr in 2006. Following this peak, emissions of HFC-23 declined rapidly to 8.6 (+0.9/−1.0 Gg/yr in 2009, the lowest annual emission of the past 15 years. We derive a 1990–2008 "bottom-up" HFC-23 emission history

  16. Review: Manfred Schulz (ed.: Entwicklungsträger in der DR Kongo. Entwicklungen in Politik, Wirtschaft, Religion, Zivilgesellschaft und Kultur (2007 Buchbesprechung: Manfred Schulz (Hrsg.: Entwicklungsträger in der DR Kongo. Entwicklungen in Politik, Wirtschaft, Religion, Zivilgesellschaft und Kultur (2007

    Directory of Open Access Journals (Sweden)

    Peter Ay

    2009-05-01

    Full Text Available Review of the edited volume: Manfred Schulz (ed.: Entwicklungsträger in der DR Kongo. Entwicklungen in Politik, Wirtschaft, Religion, Zivilgesellschaft und Kultur, Wien: Lit-Verlag 2007(= Spektrum 100; Berliner Reihe zu Gesellschaft, Wirtschaft und Politik in Entwicklungsländern 2007, ISBN 978-3825804251,755 pages. Besprechung des Sammelbandes: Manfred Schulz (Hrsg.: Entwicklungsträger in der DR Kongo. Entwicklungen in Politik, Wirtschaft, Religion, Zivilgesellschaft und Kultur, Wien: Lit-Verlag 2007 (= Spektrum 100; Berliner Reihe zu Gesellschaft, Wirtschaft und Politik in Entwicklungsländern, ISBN 978-3825804251, 755 Seiten.

  17. Induction of mitosis in the cultured rabbit lens initiated by the addition of insulin to medium KEI-4

    Energy Technology Data Exchange (ETDEWEB)

    Reddan, J R; Unakar, N J; Harding, C V; Bagchi, M; Saldana, G

    1975-01-01

    The epithelium of lenses cultured in KEI-4, a completely defined medium formulated with specific reference to the biochemistry and physiology of the rabbit lens, exhibits a pattern of cell division similar to that noted for the organ in situ. Initial fluctuations in mitotic activity occurred in the area of the germinative zone during the first 24 hr of culture. Mitosis decreased at 1 hr, was extremely low at 3 hr and returned to values comparable for lens in vivo by 22 hr. The precipitous drop in mitosis noted at 3 hr is in part attributable to the isolation of the lens from adjoining tissue. The addition of insulin to KEI-4 triggers a parasynchronous burst of DNA synthesis throughout the central lens epithelium. The activation requires the intact hormone; neither proinsulin nor the A and/or B chains of insulin, nor glucagon nor zinc chloride can initiate mitosis. The gamma-globulin-rich fraction of rabbit serum can also stimulate mitosis. The addition of dibutyryl adenosine 3':5' cyclic monophosphate (DBeAMP) plus theophylline to KEI-4-insulin inhibits mitosis and prevents the cells from entering the synthetic phase of the cell cycle. Theophylline alone or DBeAMP alone brings about a 90 percent reduction in the insulin-induced mitotic responses. Lenses exposed to insulin show a marked increase in RNA synthesis and also exhibit an increased binding of tritiated actinomycin D at 1 and 3 hr of culture relative to KEI-4 controls. The hormone apparently activates the genome including those genes governing cell division. The system is amenable for long-term culture of the mammalian lens and since the constituents of the medium are known it should be possible to determine the factor(s) in the medium which, in conjunction with insulin, are needed for the induction of cell division.

  18. New Regional and Global HFC Projections and Effects of National Regulations and Montreal Protocol Amendment Proposals

    Science.gov (United States)

    Velders, G. J. M.

    2015-12-01

    Hydrofluorocarbons (HFCs) are used as substitutes for ozone-depleting substances that are being phased out globally under Montreal Protocol regulations. New global scenarios of HFC emissions reach 4.0-5.3 GtCO2-eq yr-1 in 2050, which corresponds to a projected growth from 2015 to 2050 which is 9% to 29% of that for CO2 over the same time period. New baseline scenarios are formulated for 10 HFC compounds, 11 geographic regions, and 13 use categories. These projections are the first to comprehensively assess production and consumption of individual HFCs in multiple use sectors and geographic regions with emission estimates constrained by atmospheric observations. In 2050, in percent of global HFC emissions, China (~30%), India and the rest of Asia (~25%), Middle East and northern Africa (~10%), and USA (~10%) are the principal source regions; and refrigeration and stationary air conditioning are the major use sectors. National regulations to limit HFC use have been adopted recently in the European Union, Japan and USA, and four proposals have been submitted in 2015 to amend the Montreal Protocol to substantially reduce growth in HFC use. Calculated baseline emissions are reduced by 90% in 2050 by implementing the North America Montreal Protocol amendment proposal. Global adoption of technologies required to meet national regulations would be sufficient to reduce 2050 baseline HFC consumption by more than 50% of that achieved with the North America proposal for most developed and developing countries. The new HFC scenarios and effects of national regulations and Montreal Protocol amendment proposals will be presented.

  19. Resolution of the uncertainties in the radiative forcing of HFC-134a

    International Nuclear Information System (INIS)

    Forster, Piers M. de F; Burkholder, J.B.; Clerbaux, C.; Coheur, P.F.; Dutta, M.; Gohar, L.K.; Hurley, M.D.; Myhre, G.; Portmann, R.W.; Shine, K.P.; Wallington, T.J.; Wuebbles, D.

    2005-01-01

    HFC-134a (CF 3 CH 2 F) is the most rapidly growing hydrofluorocarbon in terms of atmospheric abundance. It is currently used in a large number of household refrigerators and air-conditioning systems and its concentration in the atmosphere is forecast to increase substantially over the next 50-100 years. Previous estimates of its radiative forcing per unit concentration have differed significantly ∼25%. This paper uses a two-step approach to resolve this discrepancy. In the first step six independent absorption cross section datasets are analysed. We find that, for the integrated cross section in the spectral bands that contribute most to the radiative forcing, the differences between the various datasets are typically smaller than 5% and that the dependence on pressure and temperature is not significant. A 'recommended' HFC-134a infrared absorption spectrum was obtained based on the average band intensities of the strongest bands. In the second step, the 'recommended' HFC-134a spectrum was used in six different radiative transfer models to calculate the HFC-134a radiative forcing efficiency. The clear-sky instantaneous radiative forcing, using a single global and annual mean profile, differed by 8%, between the 6 models, and the latitudinally-resolved adjusted cloudy sky radiative forcing estimates differed by a similar amount. We calculate that the radiative forcing efficiency of HFC-134a is 0.16+/-0.02Wm -2 ppbv -1

  20. The large contribution of projected HFC emissions to future climate forcing.

    Science.gov (United States)

    Velders, Guus J M; Fahey, David W; Daniel, John S; McFarland, Mack; Andersen, Stephen O

    2009-07-07

    The consumption and emissions of hydrofluorocarbons (HFCs) are projected to increase substantially in the coming decades in response to regulation of ozone depleting gases under the Montreal Protocol. The projected increases result primarily from sustained growth in demand for refrigeration, air-conditioning (AC) and insulating foam products in developing countries assuming no new regulation of HFC consumption or emissions. New HFC scenarios are presented based on current hydrochlorofluorocarbon (HCFC) consumption in leading applications, patterns of replacements of HCFCs by HFCs in developed countries, and gross domestic product (GDP) growth. Global HFC emissions significantly exceed previous estimates after 2025 with developing country emissions as much as 800% greater than in developed countries in 2050. Global HFC emissions in 2050 are equivalent to 9-19% (CO(2)-eq. basis) of projected global CO(2) emissions in business-as-usual scenarios and contribute a radiative forcing equivalent to that from 6-13 years of CO(2) emissions near 2050. This percentage increases to 28-45% compared with projected CO(2) emissions in a 450-ppm CO(2) stabilization scenario. In a hypothetical scenario based on a global cap followed by 4% annual reductions in consumption, HFC radiative forcing is shown to peak and begin to decline before 2050.

  1. Human safety and pharmacokinetics of the CFC alternative propellants HFC 134a (1,1,1,2-tetrafluoroethane) and HFC 227 (1,1,1,2,3,3,3-heptafluoropropane) following whole-body exposure

    NARCIS (Netherlands)

    Emmen, H.H.; Hoogendijk, E.M.G.; Klöpping-Ketelaars, W.A.A.; Muijser, H.; Duistermaat, E.; Ravensberg, J.C.; Alexander, D.J.; Borkhataria, D.; Rusch, G.M.; Schmit, B.

    2000-01-01

    HFC 134a (1,1,1,2-tetrafluoroethane) and HFC 227 (1,1,1,2,3,3,3-heptafluoropropane) are used to replace chlorofluorocarbons (CFCs) in refrigerant and aerosol applications, including medical use in metered-dose inhalers. Production and consumption of CFCs are being phased out under the Montreal

  2. Future atmospheric abundances and climate forcings from scenarios of global and regional hydrofluorocarbon (HFC) emissions

    Science.gov (United States)

    Velders, Guus J. M.; Fahey, David W.; Daniel, John S.; Andersen, Stephen O.; McFarland, Mack

    2015-12-01

    Hydrofluorocarbons (HFCs) are manufactured for use as substitutes for ozone-depleting substances that are being phased out globally under Montreal Protocol regulations. While HFCs do not deplete ozone, many are potent greenhouse gases that contribute to climate change. Here, new global scenarios show that baseline emissions of HFCs could reach 4.0-5.3 GtCO2-eq yr-1 in 2050. The new baseline (or business-as-usual) scenarios are formulated for 10 HFC compounds, 11 geographic regions, and 13 use categories. The scenarios rely on detailed data reported by countries to the United Nations; projections of gross domestic product and population; and recent observations of HFC atmospheric abundances. In the baseline scenarios, by 2050 China (31%), India and the rest of Asia (23%), the Middle East and northern Africa (11%), and the USA (10%) are the principal source regions for global HFC emissions; and refrigeration (40-58%) and stationary air conditioning (21-40%) are the major use sectors. The corresponding radiative forcing could reach 0.22-0.25 W m-2 in 2050, which would be 12-24% of the increase from business-as-usual CO2 emissions from 2015 to 2050. National regulations to limit HFC use have already been adopted in the European Union, Japan and USA, and proposals have been submitted to amend the Montreal Protocol to substantially reduce growth in HFC use. Calculated baseline emissions are reduced by 90% in 2050 by implementing the North America Montreal Protocol amendment proposal. Global adoption of technologies required to meet national regulations would be sufficient to reduce 2050 baseline HFC consumption by more than 50% of that achieved with the North America proposal for most developed and developing countries.

  3. Seaweed Fortification on Crispy Enbal as Local Food of Kei Islands

    Science.gov (United States)

    Marasabessy, Ismael; Sudirjo, Fien

    2017-10-01

    One of health problems phenomenon in Indonesian and the world is increasing the degenerative disease because human’s bad habits of eating that having less fiber. Source of fiber which is relatively abundant in eastern Indonesia is seaweed that is very precise to fortified on local food that aims to be more nutritious and economically valuable. The purpose of this study is to got appropriate seaweed fortification technique to produce Seaweed Crispy Enbal (SCE) as typical food from Kei islands that rich in fiber and preferred by consumers. The research was done in two stages. The first stage is to analyze quality of fiber and HCN content of seaweed and enbal flour as SCE raw material, and the two-stage is fortified fiber to enbal lempeng using two types of raw materials, namely pulp seaweed and flour seaweed. The results showed that the fiber content of seaweed Eucheuma cottonii and flour enbal respectively 7.01% and 4%, while HCN content less than 3 mg/kg. Fortification techniques using pulp seaweed better than others. It is because pulp seaweed produces seaweed crispy enbal with high value of sensory (really like) with having fiber content is 7.48%.

  4. Comparison of four inverse modelling systems applied to the estimation of HFC-125, HFC-134a, and SF6 emissions over Europe

    Directory of Open Access Journals (Sweden)

    D. Brunner

    2017-09-01

    Full Text Available Hydrofluorocarbons (HFCs are used in a range of industrial applications and have largely replaced previously used gases (CFCs and HCFCs. HFCs are not ozone-depleting but have large global warming potentials and are, therefore, reported to the United Nations Framework Convention on Climate Change (UNFCCC. Here, we use four independent inverse models to estimate European emissions of the two HFCs contributing the most to global warming (HFC-134a and HFC-125 and of SF6 for the year 2011. Using an ensemble of inverse models offers the possibility to better understand systematic uncertainties in inversions. All systems relied on the same measurement time series from Jungfraujoch (Switzerland, Mace Head (Ireland, and Monte Cimone (Italy and the same a priori estimates of the emissions, but differed in terms of the Lagrangian transport model (FLEXPART, NAME, inversion method (Bayesian, extended Kalman filter, treatment of baseline mole fractions, spatial gridding, and a priori uncertainties. The model systems were compared with respect to the ability to reproduce the measurement time series, the spatial distribution of the posterior emissions, uncertainty reductions, and total emissions estimated for selected countries. All systems were able to reproduce the measurement time series very well, with prior correlations between 0.5 and 0.9 and posterior correlations being higher by 0.05 to 0.1. For HFC-125, all models estimated higher emissions from Spain + Portugal than reported to UNFCCC (median higher by 390 % though with a large scatter between individual estimates. Estimates for Germany (+140 % and Ireland (+850 % were also considerably higher than UNFCCC, whereas the estimates for France and the UK were consistent with the national reports. In contrast to HFC-125, HFC-134a emissions from Spain + Portugal were broadly consistent with UNFCCC, and emissions from Germany were only 30 % higher. The data suggest that the UK over

  5. Comparison of four inverse modelling systems applied to the estimation of HFC-125, HFC-134a, and SF6 emissions over Europe

    Science.gov (United States)

    Brunner, Dominik; Arnold, Tim; Henne, Stephan; Manning, Alistair; Thompson, Rona L.; Maione, Michela; O'Doherty, Simon; Reimann, Stefan

    2017-09-01

    Hydrofluorocarbons (HFCs) are used in a range of industrial applications and have largely replaced previously used gases (CFCs and HCFCs). HFCs are not ozone-depleting but have large global warming potentials and are, therefore, reported to the United Nations Framework Convention on Climate Change (UNFCCC). Here, we use four independent inverse models to estimate European emissions of the two HFCs contributing the most to global warming (HFC-134a and HFC-125) and of SF6 for the year 2011. Using an ensemble of inverse models offers the possibility to better understand systematic uncertainties in inversions. All systems relied on the same measurement time series from Jungfraujoch (Switzerland), Mace Head (Ireland), and Monte Cimone (Italy) and the same a priori estimates of the emissions, but differed in terms of the Lagrangian transport model (FLEXPART, NAME), inversion method (Bayesian, extended Kalman filter), treatment of baseline mole fractions, spatial gridding, and a priori uncertainties. The model systems were compared with respect to the ability to reproduce the measurement time series, the spatial distribution of the posterior emissions, uncertainty reductions, and total emissions estimated for selected countries. All systems were able to reproduce the measurement time series very well, with prior correlations between 0.5 and 0.9 and posterior correlations being higher by 0.05 to 0.1. For HFC-125, all models estimated higher emissions from Spain + Portugal than reported to UNFCCC (median higher by 390 %) though with a large scatter between individual estimates. Estimates for Germany (+140 %) and Ireland (+850 %) were also considerably higher than UNFCCC, whereas the estimates for France and the UK were consistent with the national reports. In contrast to HFC-125, HFC-134a emissions from Spain + Portugal were broadly consistent with UNFCCC, and emissions from Germany were only 30 % higher. The data suggest that the UK over-reports its HFC-134a emissions to

  6. HEAT TRANSFER EVALUATION OF HFC-236FA IN CONDENSATION AND EVAPORATION

    Science.gov (United States)

    The report gives results of an evaluation of the shell-side heat transfer performance of hydrofluorocarbon (HFC)-236fa, which is considered to be a potential substitute for chlorofluorocarbon (CFC)-114 in Navy shipboard chillers, for both conventional finned [1024- and 1575-fpm (...

  7. HEAT TRANSFER EVALUATION OF HFC-236EA WITH HIGH PERFORMANCE ENHANCED TUBES IN CONDENSATION AND EVAPORATION

    Science.gov (United States)

    The report gives results of an evaluation of the heat transfer performance of pure hydrofluorocarbon (HFC)-236ea for high performance enhanced tubes which had not been previously used in Navy shipboard chillers. Shell-side heat transfer coefficient data are presented for condensa...

  8. HEAT TRANSFER EVALUATION OF HFC-236EA AND CFC-114 IN CONDENSATION AND EVAPORATION

    Science.gov (United States)

    The report gives results of a heat transfer evaluation of the refrigerants hexafluoropropane (HFC-236ea) and 1,1,2,2-dichloro-tetrafluoroethane (CFC-114). (NOTE: With the mandatory phase-out of chlorofluorocarbons (CFCs), as dictated by the Montreal Protocol and Clean Air Act Ame...

  9. MODELING AND DESIGN STUDY USING HFC-236EA AS AN ALTERNATIVE REFRIGERANT IN A CENTRIFUGAL COMPRESSOR

    Science.gov (United States)

    The report gives results of an investigation of the operation of a centrifugal compressor--part of a chlorofluorocarbon (CFC)-114 chiller installation--with the new refrigerant hydrofluorocarbon (HFC)-236ea, a proposed alternative to CFC-114. A large set of CFC-236ea operating da...

  10. Future emissions and atmospheric fate of HFC-1234yf from mobile air conditioners in Europe.

    Science.gov (United States)

    Henne, Stephan; Shallcross, Dudley E; Reimann, Stefan; Xiao, Ping; Brunner, Dominik; O'Doherty, Simon; Buchmann, Brigitte

    2012-02-07

    HFC-1234yf (2,3,3,3-tetrafluoropropene) is under discussion for replacing HFC-134a (1,1,1,2-tetrafluoroethane) as a cooling agent in mobile air conditioners (MACs) in the European vehicle fleet. Some HFC-1234yf will be released into the atmosphere, where it is almost completely transformed to the persistent trifluoroacetic acid (TFA). Future emissions of HFC-1234yf after a complete conversion of the European vehicle fleet were assessed. Taking current day leakage rates and predicted vehicle numbers for the year 2020 into account, European total HFC-1234yf emissions from MACs were predicted to range between 11.0 and 19.2 Gg yr(-1). Resulting TFA deposition rates and rainwater concentrations over Europe were assessed with two Lagrangian chemistry transport models. Mean European summer-time TFA mixing ratios of about 0.15 ppt (high emission scenario) will surpass previously measured levels in background air in Germany and Switzerland by more than a factor of 10. Mean deposition rates (wet + dry) of TFA were estimated to be 0.65-0.76 kg km(-2) yr(-1), with a maxium of ∼2.0 kg km(-2) yr(-1) occurring in Northern Italy. About 30-40% of the European HFC-1234yf emissions were deposited as TFA within Europe, while the remaining fraction was exported toward the Atlantic Ocean, Central Asia, Northern, and Tropical Africa. Largest annual mean TFA concentrations in rainwater were simulated over the Mediterranean and Northern Africa, reaching up to 2500 ng L(-1), while maxima over the continent of about 2000 ng L(-1) occurred in the Czech Republic and Southern Germany. These highest annual mean concentrations are at least 60 times lower than previously determined to be a safe level for the most sensitive aquatic life-forms. Rainwater concentrations during individual rain events would still be 1 order of magnitude lower than the no effect level. To verify these results future occasional sampling of TFA in the atmospheric environment should be considered. If future HFC-1234yf

  11. Global emissions of refrigerants HCFC-22 and HFC-134a: Unforeseen seasonal contributions

    Science.gov (United States)

    Xiang, Bin; Montzka, Stephen A.; Miller, Scot M.; Elkins, James W.; Moore, Fred L.; Atlas, Elliot L.; Miller, Ben R.; Weiss, Ray F.; Prinn, Ronald G.; Wofsy, Steven C.

    2014-01-01

    HCFC-22 (CHClF2) and HFC-134a (CH2FCF3) are two major gases currently used worldwide in domestic and commercial refrigeration and air conditioning. HCFC-22 contributes to stratospheric ozone depletion, and both species are potent greenhouse gases. In this work, we study in situ observations of HCFC-22 and HFC-134a taken from research aircraft over the Pacific Ocean in a 3-y span [HIaper-Pole-to-Pole Observations (HIPPO) 2009–2011] and combine these data with long-term ground observations from global surface sites [National Oceanic and Atmospheric Administration (NOAA) and Advanced Global Atmospheric Gases Experiment (AGAGE) networks]. We find the global annual emissions of HCFC-22 and HFC-134a have increased substantially over the past two decades. Emissions of HFC-134a are consistently higher compared with the United Nations Framework Convention on Climate Change (UNFCCC) inventory since 2000, by 60% more in recent years (2009–2012). Apart from these decadal emission constraints, we also quantify recent seasonal emission patterns showing that summertime emissions of HCFC-22 and HFC-134a are two to three times higher than wintertime emissions. This unforeseen large seasonal variation indicates that unaccounted mechanisms controlling refrigerant gas emissions are missing in the existing inventory estimates. Possible mechanisms enhancing refrigerant losses in summer are (i) higher vapor pressure in the sealed compartment of the system at summer high temperatures and (ii) more frequent use and service of refrigerators and air conditioners in summer months. Our results suggest that engineering (e.g., better temperature/vibration-resistant system sealing and new system design of more compact/efficient components) and regulatory (e.g., reinforcing system service regulations) steps to improve containment of these gases from working devices could effectively reduce their release to the atmosphere. PMID:25422438

  12. Development of two-stage compression heat pump for hot water supply in commercial use. Research of compatibility with alternative refrigerant, HFC-134a; Gyomuyo nidan asshukushiki kyuto heat pump no kaihatsu. Daitai reibai HFC-134a no tekiyosei kensho

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, K.; Hasegawa, H.; Saikawa, M.; Iwatsubo, T.; Mimaki, T. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    Performance of two-stage compression and cascade heating heat pump cycle was evaluated in the case using alternative refrigerant, HFC-134a, instead of CFC-12 through calculations and experiments. Heat source and heat load temperature conditions of CFC-12, HFC-134a, and HCFC-22 were calculated. As a result, this cycle provided equivalent coefficient of performance to use of CFC-12 and HCFC-22. Especially for HFC-134a, discharge gas temperature from compressor was much lower than that of the others, which prevented the heat decomposition of refrigerant. It was found that HFC-134a was suitable refrigerant for high temperature output equipment like this cycle. To grasp the possibility of hot water supply at 65 {degree}C and behavior of lubricating oil which can not be obtained only from calculations, applicability of HFC-134a was investigated. Experiments were conducted using a small test apparatus with electric input of 2 kW. As a result, satisfactory performance was obtained for each evaluation item. Applicability of HFC-134a to the two-stage compression cycle was confirmed. 9 refs., 21 figs., 16 tabs.

  13. Les proverbes dans Kongo Proverbs and the Origins of Bantu Wisdom par Mukumbuta Lisimba

    Directory of Open Access Journals (Sweden)

    Ludwine Mabika Mbokou

    2011-10-01

    Full Text Available

    Résumé: On emploie tous les jours des proverbes, des maximes, des devinettes et des dictons.Malgré les progrès techniques des denières décénies en matière d'outils didactiques, le proverbefait partie du quotidien des sociétés africaines en particulier et de celles du monde en général. Ilreste un instrument d'éducation indispensable et vital pour les générations futures, et quiconquedésire un conseil ou une orientation dans une certaine situation s'y réfère. Il fait partie intégrantede l'acte de communication.À la lumière des analyses du Dr Lisimba de certains proverbes de la famille bantu, nousdécouvrons l'importance que revêt la dynamique du langage offert par les proverbes. Ils peuventainsi être employés comme données dans la compilation de dictionnaires. En effet, pour la disciplinedes sciences du langage qu'est la lexicographie, le traitement des proverbes et idiomes estd'une importance capitale parce que ces derniers sont le véhicule de la culture et des moeurs d'unpeuple. Ainsi, pour mener à bien une telle entreprise, le lexicographe devra choisir le traitement àl'intérieur de la liste centrale, sinon à l'extérieur de la liste centrale, l'option la plus profitable pourlui restant une classification thématique qui tient compte non seulement de l'aspect sémantique duproverbe, mais aussi de son aspect formel.

    Mots-clés: ANALYSE FORMELLE, ANALYSE SÉMANTIQUE, CLASSIFICATION THÉMATIQUE,DIDACTIQUE, DICTIONNAIRE, GENRE PROVERBIAL, IDIOMES, LEXICOGRAPHE,LEXICOGRAPHIE, LISTE CENTRALE, LITTÉRATURE ORALE, PRÉ-TEXTES, POST-TEXTES,PROVERBES

    Abstract: Proverbs according to Kongo Proverbs and the Origins of Bantu Wisdom by Mukumbuta Lisimba. Proverbs, maxims, riddles and sayings are used every day. In spite of the technical progress during the last decades as far as didactic tools are concerned, the proverb forms part of the daily life of African societies in particular and those of the world in

  14. Laju Pertumbuhan SomatikKappaphycus alvarezii Di Perairan Desa Sathean Kecamatan Kei Kecil Kabupaten Maluku Tenggara

    Directory of Open Access Journals (Sweden)

    Nally Y.G.F. Erbabley

    2014-05-01

    Full Text Available Rumput laut Kappaphycus alvareziidijadikan unggulan bagi pengembangan dan peningkatan komoditi sumber daya laut di Maluku Tenggara dan merupakan komoditas unggulan yang ditetapkan oleh PEMDA Maluku Tenggara. Aspek penting dan karakteristik menguntungkan yang berkaitan dengan pengembangan budidaya rumput laut ini antara lain meliputi aspek ekonomi, Tujuan penelitian ini adalah untuk mengetahui laju pertumbuhan harian (pertumbuhan somatik Kappaphycus alvarezii varieatas hijau dan coklatdi perairan desa Sathean Kecamatan Kei Kecil Kabupaten Maluku Tenggara.Penelitian dilakukan di perairan desa Sathean pada bulan Januari-September 2013 dengan 2 (dua perlakuan bibit yang dipelihara selama 6 kali musim tanam.Pemeliharaan Kappaphycus alvarezii menggunakan metode longline. Hasil penelitian menunjukanparameter kualitas air diamati secara in-situ selama pemeliharaan berlangsung.Oksigen terlarut (DO pada stasiun I - III berkisar antara 3.4-4.58  ppm,  suhu  300C,  salinitas  antara  27-32  ppt,  pH  berkisara  antara  8.15-8.26. Sedangkan nilai nitrit (NO2 0.009 mg/L, nitrat (NO3 < 5 mg/L,  ammonia (NH3 berkisar antara 0.0010– 0.126mg/L dan phosphat (PO4 berkisar antara <0.25 mg/L.Laju pertumbuhan harian dan laju pertumbuhan rata-rata harian Kappaphycus alvarezii selama pemeliharaan (42 hari adalah nilai rata-rata pengukuran rumpur laut pada long line 1- long line 5, dengan periode penanaman I - IV di desa Sathean diperoleh untuk bibit varietas hijau (BHT berat rata-rata tertinggi ditemukan pada periode penanaman IV pada long line 4 dengan berat yaitu 407 gr sedangkan nilai rata-rata terendah ditemukan pada periode penanaman I pada long line 5 dengan berat 24 gr. Sebaliknya berat  rata-rata rumput laut dengan bibit varietas coklat (BCT ditemukan bahwa berat tertinggi masih pada periode ke IV long line ke 2, dengan berat 427 gr sedangkan berat terendah ditemukan pada periode penanaman I long line 5 dengan berat 52 gr. Waktu tanam pada bulan

  15. Investigation into the conditions under which HFC134a may become flammable.

    CSIR Research Space (South Africa)

    Kramers, AP

    2002-01-01

    Full Text Available or approaching 180°C would be associated with an onset of catastrophic conditions such as plant room fires and total mechanical failure of equipment. It is suggested in that the guidelines listed in Section 5.2, pertaining to abnormal plant conditions... /lubricant mixtures can become explosive. The work must therefore consider both normal and abnormal operating conditions to which HFC134a may be exposed to empower machine operators, mine maintenance personnel and contractors to take preventative...

  16. FY 1999 survey report on the survey of destruction technology of HFC, etc. for rationalization of energy use. Survey of the actual state of use/recovery/emissions of HFC, etc.; 1999 nendo energy shiyo gorika HFC nado hakai shori gijutsu chosa hokokusho. HFC nado shiyo kaishu haishutsu jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey was aimed at collecting the basic data for studying a possibility of conversion of the recovery system of refrigerant freons, mostly DFC, into HFC, etc., which has been proceeded with in Japan. Of HFCs, PFCs and SF{sub 6} used for survey, only SF{sub 6} is now being recovered and processed. As to HFCs, HFC-134a was arranged, and the recovery/destruction to meet users' handling methods are requested because of the diverse usage and users. The points of the control of emissions of chemical substances into the atmosphere are the decrease in number of times of transport/filling-up at the time of materials handling and the closed system in plants and installation. If considering the heightening of efficiency of materials flow, requested are the decrease in number of times of transport/filling-up, the increase in quantity received by users, and measures to be taken for leakage at the time of receiving. In relation to the conversion of the recovery system of refrigerant freons, mainly CFC, into HFC, etc., all the industries concerned with the generation of the used substances to the materials flow have to promote the technical development for the structure and recovery in cooperation with each other. (NEDO)

  17. Experimental investigation of hydrocarbon mixtures to replace HFC-134a in an automotive air conditioning system

    International Nuclear Information System (INIS)

    Wongwises, Somchai; Kamboon, Amnouy; Orachon, Banchob

    2006-01-01

    This paper presents an experimental study on the application of hydrocarbon mixtures to replace HFC-134a in automotive air conditioners. The hydrocarbons investigated are propane (R290), butane (R600) and isobutane (R600a). The measured data are obtained from an automotive air conditioning test facility utilizing HFC-134a as the refrigerant. The air conditioner, with a capacity of 3.5 kW driven by a Diesel engine, is charged and tested with four different ratios of hydrocarbon mixtures. The experiments are conducted at the same surrounding conditions. The temperature and pressure of the refrigerant at every major position in the refrigerant loop, the temperature, flow rate and humidity of air, torque and engine speed are recorded and analyzed. The parameters investigated are the refrigeration capacity, the compressor power and the coefficient of performance (COP). The results show that propane/butane/isobutane: 50%/40%/10% is the most appropriate alternative refrigerant to replace HFC-134a, having the best performance of all the hydrocarbon mixtures investigated

  18. HFC-152a and HFC-134a emission estimates and characterization of CFCs, CFC replacements, and other halogenated solvents measured during the 2008 ARCTAS campaign (CARB phase) over the South Coast Air Basin of California

    Science.gov (United States)

    Barletta, B.; Nissenson, P.; Meinardi, S.; Dabdub, D.; Sherwood Rowland, F.; Vancuren, R. A.; Pederson, J.; Diskin, G. S.; Blake, D. R.

    2011-03-01

    This work presents results from the NASA Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) study. Whole air samples were obtained on board research flights that flew over California during June 2008 and analyzed for selected volatile organic compounds, including several halogenated species. Samples collected over the South Coast Air Basin of California (SoCAB), which includes much of Los Angeles (LA) County, were compared with samples from inflow air masses over the Pacific Ocean. The levels of many halocarbon species were enhanced significantly over the SoCAB, including compounds regulated by the Montreal Protocol and subsequent amendments. Emissions estimates of HFC-152a (1,1-difluoroethane, CH3CHF2; 0.82 ± 0.11 Gg) and HFC-134a (1,1,1,2-tetrafluoroethane, CH2FCF3; 1.16 ± 0.22 Gg) in LA County for 2008 were obtained using the observed HFC:carbon monoxide (CO) enhancement ratio. Emission rates also were calculated for the SoCAB (1.60 ± 0.22 Gg yr-1 for HFC-152a and 2.12 ± 0.28 Gg yr-1 for HFC-134a) and then extrapolated to the United States (32 ± 4 Gg yr-1 for HFC-152a and 43 ± 6 Gg yr-1 for HFC-134a) using population data. In addition, emission rates of the two HFCs in LA County and SoCAB were calculated by a second method that utilizes air quality modeling. Emissions estimates obtained using both methods differ by less than 25% for the LA County and less than 45% for the SoCAB.

  19. HFC-152a and HFC-134a emission estimates and characterization of CFCs, CFC replacements, and other halogenated solvents measured during the 2008 ARCTAS campaign (CARB phase over the South Coast Air Basin of California

    Directory of Open Access Journals (Sweden)

    B. Barletta

    2011-03-01

    Full Text Available This work presents results from the NASA Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS study. Whole air samples were obtained on board research flights that flew over California during June 2008 and analyzed for selected volatile organic compounds, including several halogenated species. Samples collected over the South Coast Air Basin of California (SoCAB, which includes much of Los Angeles (LA County, were compared with samples from inflow air masses over the Pacific Ocean. The levels of many halocarbon species were enhanced significantly over the SoCAB, including compounds regulated by the Montreal Protocol and subsequent amendments. Emissions estimates of HFC-152a (1,1-difluoroethane, CH3CHF2; 0.82 ± 0.11 Gg and HFC-134a (1,1,1,2-tetrafluoroethane, CH2FCF3; 1.16 ± 0.22 Gg in LA County for 2008 were obtained using the observed HFC:carbon monoxide (CO enhancement ratio. Emission rates also were calculated for the SoCAB (1.60 ± 0.22 Gg yr−1 for HFC-152a and 2.12 ± 0.28 Gg yr−1 for HFC-134a and then extrapolated to the United States (32 ± 4 Gg yr−1 for HFC-152a and 43 ± 6 Gg yr−1 for HFC-134a using population data. In addition, emission rates of the two HFCs in LA County and SoCAB were calculated by a second method that utilizes air quality modeling. Emissions estimates obtained using both methods differ by less than 25% for the LA County and less than 45% for the SoCAB.

  20. Modelling of fluid flow through short tube orifices under metastable conditions: A new numerical validation approach for evaluating the mass flow rate with refrigerant mixtures (HFC-407C and HFC-410A)

    International Nuclear Information System (INIS)

    García-Valladares, O.; Santoyo, E.

    2014-01-01

    In a previous work, one-dimensional numerical modelling of fluid-flow inside short tube orifices was performed, and successfully validated against a wide range of mass flow rate measurements reported for the refrigerant HFC-134a. Governing equations of continuity, momentum, energy and entropy were solved for describing the fluid flow under a wide variety of thermodynamic transitions (e.g., subcooled liquid region, metastable liquid region, metastable two-phase region and equilibrium two-phase region), including sudden contraction and enlargement. In this new study, a comprehensive comparison analysis between numerical simulation data and experimental measurements obtained for HFC-407C and HFC-410A refrigerants (N o  = 241) to extend the applicability of the same mathematical model was carried out. Using a widespread statistical analysis, based on weighted linear regressions with an outlier detection/rejection module at 95% of confidence level, the prediction performance of the mathematical model was again assessed. Linear regressions between predicted mass flow rate data and experimental measurements were computed, and used them as a statistical comparison criterion. A statistical comparison between predicted simulation results and mass flow rate experimental data are reported. Average deviation errors of ±11.1% (for the refrigerant HFC-407C) and ±7.3% (for refrigerant HFC-410A) were found between numerical model and experimental data. These results demonstrate a new and robust application of the model to predict reliably the mass flow rate through short tube orifices under metastable conditions, which enable this tool to be reliably used for the design of short tube orifices. - Highlights: •A modelling for evaluating short tube orifice was developed for refrigerant mixtures. •The numerical model applied considered metastable regions and choke flow. •The model was validated against experimental data for HFC-407C and HFC-410A. •Statistical analysis based

  1. The inventory of mollusc species and its potent on seagrass bed in Kei Kecil Islands, Southeast Moluccas

    Directory of Open Access Journals (Sweden)

    AGUS KUSNADI

    2008-10-01

    Full Text Available Inventory of mollusk species and its potential on sea grass bed in Kei Kecil islands, Southeast Moluccas have been conducted by using quadrate-transect line method. The study was carried out in February-August 2007. There were 103 species of mollusk observed, 80 species belong to gastropods and 23 belong to bivalves. From the total species, 72 of them were reported as the potential species and the others still unknown. Most of potential group was used as food resources (55 species and other species were potential as decoration, souvenir, ornament, and accessories (31 species. Some species were potential for building material, knife tool, barter tool and bioactive compounds. The top shells (Trochus niloticus, the giant clams (Tridacna spp. and Hippopus hippopus and the abalone (Haliotis spp. were the major trading commodities for shellfish fisheries.

  2. Gonçalves, António Custódio: A história revisitada do Kongo e de Angola. Lisboa: Editorial Estampa, 2005

    Directory of Open Access Journals (Sweden)

    Rosana Gonçalves

    2006-12-01

    Full Text Available Antônio Custódio Gonçalves é sociólogo e professor catedrático de Geografia da Universidade do Porto, onde dirige o Centro de Estudos Africanos (CEAUP, coordenando um importante periódico sobre África, a Africana Studia. Há anos debruçado sobre temáticas africanas, António Custódio Gonçalves sintetiza muitas das complexas questões sobre a história do Kongo e Angola nesta publicação.

  3. Sudden death involving inhalation of 1,1-difluoroethane (HFC-152a) with spray cleaner: three case reports.

    Science.gov (United States)

    Sakai, Kentaro; Maruyama-Maebashi, Kyoko; Takatsu, Akihiro; Fukui, Kenji; Nagai, Tomonori; Aoyagi, Miwako; Ochiai, Eriko; Iwadate, Kimiharu

    2011-03-20

    Spray cleaner is a cleaning product containing compressed 1,1-difluoroethane (HFC-152a) to blow dust off electric devices and other sensitive equipment; however, it is also inhaled to induce euphoria. This report describes three cases of death involving HFC-152a inhalation with spray cleaner under different circumstances. In case 1, death was during inhalation for euphoria with which led to having frostbite. In case 2, death may have been associated with suicidal intention. Case 3 was also considered an accidental autoerotic death. In all three cases, HFC-152a was detected at 99.2-136.2mg/l in blood samples, 94.5-191.9 mg/l in urine samples and 3.6-18.4 mg in the gastric contents according to gas chromatography with flame ionization detection. To prevent death associated with HFC-152a inhalation from spray cleaner, the danger of the sudden death should be announced to people, given the ready availability of commercial products containing HFC-152a. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  4. Photoionization and dissociative photoionization study of HFC-152a using synchrotron radiation

    International Nuclear Information System (INIS)

    Huang Chaoqun; Wei Lixia; Yang Bin; Yang Rui; Wang Sisheng; Shan Xiaobin; Qi Fei; Zhang Yunwu; Sheng Liusi; Hao Liqing; Zhou Shikang; Wang Zhenya

    2006-01-01

    Photoionization and dissociative photoionization of HFC-152a have been studied using synchrotron radiation and a reflection time-of-flight mass spectrometry (RTOF-MS). The ionization energy of parent molecule (11.94 ± 0.04 eV) and appearance potentials of various fragment ions have been determined by measuring their photoionization efficiency curves. Energies, symmetry point groups and ground electronic states of neutrals and cations of parent and its fragments have been calculated using GAUSSIAN-03 program with the G3 method. According to the theoretical and experimental results, some dissociation channels and their dissociation energies of CH 3 CHF 2 + have been analyzed. (authors)

  5. Preparation of HfC single crystals by a floating zone technique

    International Nuclear Information System (INIS)

    Otani, S.; Tanaka, T.

    1981-01-01

    HfC single crystals have been prepared using a floating zone technique by controlling the compositions of the initial molten zone and the feed rod. The obtained crystal rods were 6 cm long and 0.9 cm in diameter. The various parts of the crystal rods have nearly constant compositions (C/Hf(ZR) = 0.956-0.977), and do not contain any free carbon. The impurities in the crystal, evaporation product, and starting material were examined by fluorescence X-ray spectroscopy. The refining effect due to evaporation was discussed. (orig.)

  6. HFC404A vaporisation inside a Brazed Plate Heat Exchanger (BPHE): Comparison with the possible long-term low GWP substitutes HC290 (Propane) and HC1270 (Propylene)

    International Nuclear Information System (INIS)

    Longo, Giovanni A.; Mancin, Simone; Righetti, Giulia; Zilio, Claudio

    2016-01-01

    Highlights: • This paper investigates HFC404A vaporisation inside a BPHE. • HC290 and HC1270 exhibit heat transfer coefficients similar to HFC404A. • HC290 and HC1270 exhibit frictional pressure drops higher than HFC404A. • The experimental measurements are complemented with an IR thermography analysis. - Abstract: This paper presents the heat transfer coefficients and the pressure drops measured during HFC404A vaporisation inside a commercial BPHE and the comparison of this data with previous measurements carried out during HC290 (Propane) and HC1270 (Propylene) vaporisation inside the same BPHE and similar operating condition in order to assess the capability of HydroCarbon refrigerants as long-term low GWP substitutes for HFC404A in commercial and industrial refrigeration. Propane and Propylene exhibit boiling heat transfer coefficient very similar and frictional pressure drops higher than to those of HFC404A, therefore, taking into account also their good thermodynamic properties, they seems to be very promising as long-term low GWP substitutes for HFC404A. The HFC404A boiling heat transfer coefficients were also compared with a new model for refrigerant boiling inside BPHE (Longo et al., 2015): the mean absolute percentage deviation between calculated and experimental data is 6.0%. The heat transfer measurements were also complemented with an IR thermography analysis for a better understanding of refrigerant vaporisation heat transfer regime inside a BPHE.

  7. Experimental investigation of HFC407C/HC290/HC600a mixture in a window air conditioner

    International Nuclear Information System (INIS)

    Jabaraj, D.B.; Avinash, P.; Lal, D. Mohan; Renganarayan, S.

    2006-01-01

    HCFC22, one of the widely used refrigerants in window air conditioners must be phased out soon as per the Montreal protocol. Presently, HFC407C is considered as a potential drop in substitute for HCFC22, but retrofitting HCFC22 systems with HFC407C with polyol ester oil (POE) is a major issue as HFC407C is immiscible with mineral oil. The miscibility issue of HFC407C with mineral oil was overcome with the addition of a HC blend to it. The above technoeconomic feasibility issues to retrofit the existing HCFC22 systems with an ozone friendly refrigerant and retain the energy efficiency of the system are challenges in the air conditioning sector. In this present work, an experimental analysis has been conducted in a window air conditioner retrofitted with eco-friendly refrigerant mixtures of HFC407C/HC290/HC600a without changing the mineral oil. Its performance, as well as energy consumption, was compared with the conventional one. It is observed that the mixtures demand lengthening of the condenser in order to maintain the discharge pressure within acceptable limits. This also resulted in better heat transfer at the condenser. Therefore, in this study, the condenser tube length was increased by 19% to suit the mixtures as compared to HCFC22. Compared to HCFC22, the refrigeration capacity of the new mixture was 9.54-12.76% higher than that of HCFC22, while the actual COP was found to be 11.91-13.24% higher than that of HCFC22. The overall performance has proved that the HFC407C/HC blend refrigerant mixture could be an eco-friendly substitute to phase out HCFC22

  8. Viscosity Measurements and Correlations for 1,1,1,2-tetrafluoroethane (HFC-134a) up to 140 MPa

    DEFF Research Database (Denmark)

    Comuñas, M.J.P.; Baylaucq, A.; Cisneros, Sergio

    2003-01-01

    In spite of being one of the most studied refrigerants, large discrepancies in the experimental determination of the dynamic viscosity of 1, 1, 1,2-tetrafluoroethane (HFC-134a) prevail. Additionally, there is a need for supplementary high-pressure measurements that can help to derive sound general...... correlations for the viscosity of this compound. Hence, in this work new dynamic viscosity measurements for HFC-134a using a falling-body viscometer in the temperature range of 293.15-373.15 K and pressures up to 140 MPa are presented. This work high-pressure data in combination with already published data...

  9. Action mechanism of hydrogen gas on deposition of HfC coating using HfCl{sub 4}-CH{sub 4}-H{sub 2}-Ar system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yalei, E-mail: yaleipm@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); School of Metallurgy and Environment, Central South University, Changsha, 410083 (China); Li, Zehao [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); Xiong, Xiang, E-mail: xiongx@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); Li, Xiaobin [School of Metallurgy and Environment, Central South University, Changsha, 410083 (China); Chen, Zhaoke; Sun, Wei [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China)

    2016-12-30

    Highlights: • HfC coatings were deposited on C/C composites by LPCVD using HfCl4-CH4-H2-Ar system. • Action mechanism of H2 on structure and growth behavior of HfC coating was studied. • Increased H2 concentration leads to transformation in growth mechanism of coating. - Abstract: Hafnium carbide coatings were deposited on carbon/carbon composites by low pressure chemical vapor deposition using HfCl{sub 4}-CH{sub 4}-H{sub 2}-Ar system. The microstructure, mechanical and ablation resistance performance of HfC coatings deposited with various H{sub 2} concentrations were investigated. The effect of hydrogen gas on the deposition of HfC coating was also discussed. Results show that all of the deposited coatings are composed of single cubic HfC phase, the hydrogen gas acted as a crucial role in determining the preferred orientation, microstructure and growth behavior of HfC coatings. During the deposition process, the gas phase supersaturation of the reaction species can be controlled by adjusting the hydrogen gas concentration. When deposited with low hydrogen gas concentration, the coating growth was dominated by the nucleation of HfC, which results in the particle-stacked structure of HfC coating. Otherwise, the coating growth was dominated by the crystal growth at high hydrogen gas concentration, which leads to the column-arranged structure of HfC coating. Under the ablation environment, the coating C2 exhibits better configurational stability and ablation resistance. The coating structure has a significant influence on the mechanical and ablation resistance properties of HfC coating.

  10. Experimental evaluation of automotive air-conditioning using HFC-134a and HC-134a

    Science.gov (United States)

    Nasution, Henry; Zainudin, Muhammad Amir; Aziz, Azhar Abdul; Latiff, Zulkarnain Abdul; Perang, Mohd Rozi Mohd; Rahman, Abd Halim Abdul

    2012-06-01

    An experimental study to evaluate the energy consumption of an automotive air conditioning is presented. In this study, these refrigerants will be tested using the experimental rig which simulated the actual cars as a cabin complete with a cooling system component of the actual car that is as the blower, evaporator, condenser, radiators, electric motor, which acts as a vehicle engine, and then the electric motor will operate the compressor using a belt and pulley system, as well as to the alternator will recharge the battery. The compressor working with the fluids HFC-134a and HC-134a and has been tested varying the speed in the range 1000, 1500, 2000 and 2500 rpm. The measurements taken during the one hour experimental periods at 2-minutes interval times for temperature setpoint of 20°C with internal heat loads 0, 500, 700 and 1000 W. The final results of this study show an overall better energy consumption of the HFC-134a compared with the HC-134a.

  11. A molecular orbital study on the oxidative decomposition of HFC-32

    International Nuclear Information System (INIS)

    Mochizuki, Yuji

    1999-03-01

    A series of ab initio molecular orbital calculations, in which Hartree-Fock, second-order Moeller-Plesset perturbation, density functional (B3LYP and BHandHLYP) levels of theory were used, was performed on the elementary reactions related to the oxidative decomposition of HFC-32 (CH 2 F 2 ) by hydroxyl (OH) radicals in a supercritical water condition (so-called SCWO). The whole process is written as CH 2 F 2 + 4OH → CO 2 + 2H 2 O + 2HF and consists of (1) H abstraction by OH to form H 2 O, (2) OH coupling to C-center, and (3) HF leaving to form C=O bond. Molecular geometries were optimized at each level of theory. The HF leaving was found to be the rate-determining step, but its barrier height was lowered by the reactive solvation with an extra H 2 O. Calculations implied that the SCWO of HFC-32 can proceed efficiently. (author)

  12. US emissions of HFC-134a derived for 2008-2012 from an extensive flask-air sampling network

    NARCIS (Netherlands)

    Hu, Lei; Montzka, Stephen A.; Miller, John B.; Andrews, Aryln E.; Lehman, Scott J.; Miller, Benjamin R.; Thoning, Kirk; Sweeney, Colm; Chen, Huilin; Godwin, David S.; Masarie, Kenneth; Bruhwiler, Lori; Fischer, Marc L.; Biraud, Sebastien C.; Torn, Margaret S.; Mountain, Marikate; Nehrkorn, Thomas; Eluszkiewicz, Janusz; Miller, Scot; Draxler, Roland R.; Stein, Ariel F.; Hall, Bradley D.; Elkins, James W.; Tans, Pieter P.

    2015-01-01

    U.S. national and regional emissions of HFC-134a are derived for 2008-2012 based on atmospheric observations from ground and aircraft sites across the U.S. and a newly developed regional inverse model. Synthetic data experiments were first conducted to optimize the model assimilation design and to

  13. A fundamental equation of state for 1,1-difluoroethane (HFC-152a)

    Science.gov (United States)

    Tillner-Roth, R.

    1995-01-01

    A fundamental equation ofstale for HFC-152a ( 1,1-dilluorocthane) is presented covering temperatures between the triple-point temperature ( 154.56 K) and 435 K for pressures up to 311 M Pa. The equation is based on reliable ( p, g, T) data in the range mentioned above. These are generally represented within ±0.1 % of density. Furthermore. experimental values of the vapor pressure, the saturated liquid density, and some isobaric heat capacities in the liquid were included during the correlation process. The new equation of state is compared with experimental data and also with the equation of state developed by Tamatsu et al. Differences between the two equations of state generally result from using different experimental input data. It is shown that the new equation of state allows an accurate calculation of various thermodynamic properties for most technical applications.

  14. Performance Analysis of a Centrifugal Compressor for HFC-134a with aviation of Diffuser Vane Angle

    International Nuclear Information System (INIS)

    Park, Han Young; Chung, Jin Taek; Shin, You Hwan; Lee, Yoon Pyo; Kim, Kwang Ho; Cho, Yong Hun; Kim, Jong Seong

    2007-01-01

    Numerical simulation on the two-stage centrifugal compressor with Low Solidity Vaned Diffuser (LSVD) for HFC-134a turbo-chiller was performed using a commercial code. The comparative study with experimental results from other compressor was also investigated to testify the simulation schemes. The numerical analysis was separately simulated for each stage of the compressor and the effect of impeller-diffuser flow interaction was considered. Setting angle of the diffuser vane changed in the range of 15 .deg. and the effects on its variation were discussed in detail including the flow analysis in the passage of the compressor. The vane setting angle obtained from the preliminary design was slightly adjusted to the optimal value by the performance enhancement in terms of pressure recovery and flow characteristics

  15. Inventory and mitigation opportunities for HFC-134a emissions from nonprofessional automotive service

    Science.gov (United States)

    Zhan, Tao; Potts, Winston; Collins, John F.; Austin, Jeff

    2014-12-01

    Many vehicle owners in the United States recharge their vehicles' air conditioning systems with small containers of hydrofluorocarbon-134a (HFC-134a, CH2FCF3), at a frequency estimated to be once every year on average. Such nonprofessional service produces immediate emissions of this potent greenhouse gas during service and from the residual heel in partially used containers. The nonprofessional operations are also associated with increased delayed refrigerant emissions that occur because owners are less likely to repair leaks than professional technicians. In California, an estimated 1.3 million nonprofessional service operations performed each year generate 0.27 ± 0.07 million metric ton CO2 equivalent (MMTCO2e) of immediate emissions and 0.54 ± 0.08 MMTCO2e of delayed emissions, using a Global Warming Potential of 1300 for HFC-134a. The immediate emissions can be largely mitigated by a regulation that requires self-sealing valves and improved labeling instructions on the containers, a deposit-return-recycling program for the containers, and a consumer education program. If 95% of the used containers were to be returned by consumers for recycling of the container heel, the annual immediate emissions would be reduced by 0.26 ± 0.07 MMTCO2e. In the United States, an estimated 24 million nonprofessional service operations are performed each year, generating 5.1 ± 1.4 MMTCO2e of immediate emissions and 10.4 ± 1.5 MMTCO2e of delayed emissions. Mitigation measures equivalent to the California regulation would reduce nationwide immediate emissions by 4.9 ± 1.4 MMTCO2e, if 95% of the used cans were returned for recycling. These business-as-usual emissions and mitigation potentials are projected to stay approximately constant until around 2022, and remain at significant levels into the 2030s.

  16. Impact of tidal phenomenon “Met Ef” on the exploitation of benthos at inshore shoals in Kei islands, Indonesia

    Science.gov (United States)

    Renjaan, Eugenius Alfred; Makailipessy, Marvin Mario

    2017-10-01

    A study on benthos exploitation at five shoals located in Rosenberg and Nerong Straits, the kei islands had been conducted during period of the lowest ebb tide phenomenon which locally termed Met Ef on 2016. The purpose of the study is to know the impact of the Met Ef on benthos exploitation at the shoals by local communities during the Met Ef. Data of tidal amplitudes were obtained from the Tide Charts Mobile Applications which confirmed the observations on tide pole during October, November, and December 2013 until 2016. Data of benthos exploited during periods of Met Ef at the shoals was obtained through direct observation on benthos exploited by the local communities, also by interviewing them using questionnaires. The results showed that the lowest ebb tide of the Met Ef occurred in November, i.e., at 2 to 5 days after the full moon and/or new moon, with an average tidal range of 2.66 m and even have ever one reached 2.80 m. The most exploited benthos at the shoals is Giant clam (Tridacna sp.), Spider conch (Lambis sp.), Hammer oyster (Malleus sp.), Octopus (Octopus spp.). The intensity of benthos exploited at the shoals increased during the period of Met Ef especially in October because at that time the sea was very calm and clear due to relatively lower wind speed and the rain fall was relatively lower. This has promoted an easier accessibility of the communities to exploit benthos at shoals and, therefore October is considered by the local communities as the peak of Met Ef, instead of November. During November and, December the availability of benthos in shoals has been reduced due to it has been exploited intensely in October.

  17. Fasting plasma zeaxanthin response to Fructus barbarum L. (wolfberry; Kei Tze) in a food-based human supplementation trial.

    Science.gov (United States)

    Cheng, Chung Yuen; Chung, Wai Yuen; Szeto, Yim Tong; Benzie, Iris F F

    2005-01-01

    Age-related macular degeneration (AMD) is a common disorder that causes irreversible loss of central vision. Increased intake of foods containing zeaxanthin may be effective in preventing AMD because the macula accumulates zeaxanthin and lutein, oxygenated carotenoids with antioxidant and blue light-absorbing properties. Lycium barbarum L. is a small red berry known as Fructus lycii and wolfberry in the West, and Kei Tze and Gou Qi Zi in Asia. Wolfberry is rich in zeaxanthin dipalmitate, and is valued in Chinese culture for being good for vision. The aim of this study, which was a single-blinded, placebo-controlled, human intervention trial of parallel design, was to provide data on how fasting plasma zeaxanthin concentration changes as a result of dietary supplementation with whole wolfberries. Fasting blood was collected from healthy, consenting subjects; fourteen subjects took 15 g/d wolfberry (estimated to contain almost 3 mg zeaxanthin) for 28 d. Repeat fasting blood was collected on day 29. Age- and sex-matched controls (n 13) took no wolfberry. Responses in the two groups were compared using the Mann-Whitney test. After supplementation, plasma zeaxanthin increased 2.5-fold: mean values on day 1 and 29 were 0.038 (sem 0.003) and 0.096 (sem 0.009) micromol/l (P0.05), respectively, for the control group. This human supplementation trial shows that zeaxanthin in whole wolfberries is bioavailable and that intake of a modest daily amount markedly increases fasting plasma zeaxanthin levels. These new data will support further study of dietary strategies to maintain macular pigment density.

  18. Observations of 1,1-difluoroethane (HFC-152a) at AGAGE and SOGE monitoring stations in 1994-2004 and derived global and regional emission estimates

    Science.gov (United States)

    Greally, B. R.; Manning, A. J.; Reimann, S.; McCulloch, A.; Huang, J.; Dunse, B. L.; Simmonds, P. G.; Prinn, R. G.; Fraser, P. J.; Cunnold, D. M.; O'Doherty, S.; Porter, L. W.; Stemmler, K.; Vollmer, M. K.; Lunder, C. R.; Schmidbauer, N.; Hermansen, O.; Arduini, J.; Salameh, P. K.; Krummel, P. B.; Wang, R. H. J.; Folini, D.; Weiss, R. F.; Maione, M.; Nickless, G.; Stordal, F.; Derwent, R. G.

    2007-03-01

    Ground-based in situ measurements of 1,1-difluoroethane (HFC-152a, CH3CHF2) which is regulated under the Kyoto Protocol are reported under the auspices of the AGAGE (Advanced Global Atmospheric Gases Experiment) and SOGE (System of Observation of halogenated Greenhouse gases in Europe) programs. Observations of HFC-152a at five locations (four European and one Australian) over a 10 year period were recorded. The annual average growth rate of HFC-152a in the midlatitude Northern Hemisphere has risen from 0.11 ppt/yr to 0.6 ppt/yr from 1994 to 2004. The Southern Hemisphere annual average growth rate has risen from 0.09 ppt/yr to 0.4 ppt/yr from 1998 to 2004. The 2004 average mixing ratio for HFC-152a was 5.0 ppt and 1.8 ppt in the Northern and Southern hemispheres, respectively. The annual cycle observed for this species in both hemispheres is approximately consistent with measured annual cycles at the same locations in other gases which are destroyed by OH. Yearly global emissions of HFC-152a from 1994 to 2004 are derived using the global mean HFC-152a observations and a 12-box 2-D model. The global emission of HFC-152a has risen from 7 Kt/yr to 28 Kt/yr from 1995 to 2004. On the basis of observations of above-baseline elevations in the HFC-152a record and a consumption model, regional emission estimates for Europe and Australia are calculated, indicating accelerating emissions from Europe since 2000. The overall European emission in 2004 ranges from 1.5 to 4.0 Kt/year, 5-15% of global emissions for 1,1-difluoroethane, while the Australian contribution is negligible at 5-10 tonnes/year, <0.05% of global emissions.

  19. Isosteric heats of adsorption extracted from experiments of ethanol and HFC 134a on carbon based adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    El-Sharkawy, Ibrahim I.; Saha, Bidyut B.; Koyama, Shigeru [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga-koen 6-1, Kasuga-shi, Fukuoka 816-8580 (Japan); Srinivasan, Kandadai [School of Engineering and Logistics, Charles Darwin University, Darwin NT 0909 (Australia)

    2007-03-15

    The purpose of this paper is to provide empirical correlations for isosteric heats of adsorption on carbon based adsorbents for two refrigerants namely ethanol and HFC 134a. A non-dimensional correlation which partitions the contributions of the concentration and temperature dependence is proposed. The correlation is tested out against data obtained from experimental isotherms of ethanol adsorption on activated carbon fibers [ACF (A-20) and ACF (A-15)] and HFC 134a on two specimens of activated carbon powders and one specimen of carbon granules. It is expected that the suggested correlation will be useful for designers of adsorption chillers where indenting heat inventories fulcrums on the magnitude of isosteric heat of adsorption. (author)

  20. Final Project Closeout Report for Sprint Hydrogen Fuel Cell (HFC) Deployment Project in California, Gulf Coast and Eastern Seaboard Markets

    Energy Technology Data Exchange (ETDEWEB)

    Kenny, Kevin [Sprint, Reston, VA (United States); Bradley, Dwayne [Burns & McDonnell, Kansas City, MO (United States)

    2015-09-01

    Sprint is one of the telecommunications industry leaders in the deployment of hydrogen fuel cell (HFC) systems to provide backup power for their mission critical wireless network facilities. With several hundred fuel cells commissioned in California, states in the gulf coast region, and along the upper eastern seaboard. A strong incentive for advancing the integration of fuel cells into the Sprint network came through the award of a Department of Energy (DOE) grant focused on Market Transformation activities for project (EE0000486). This grant was funded by the 2009 American Recovery and Reinvestment Act (ARRA). The funding provided by DOE ($7.295M) was allocated to support the installation of 260 new HFC systems, equipped with an on-site refillable Medium Pressure Hydrogen Storage Solution (MPHSS), as well as for the conversion of 21 low pressure hydrogen systems to the MPHSS, in hopes of reducing barriers to market acceptance.

  1. Recent increases in the atmospheric growth rate and emissions of HFC-23 (CHF3 and the link to HCFC-22 (CHClF2 production

    Directory of Open Access Journals (Sweden)

    P. G. Simmonds

    2018-03-01

    Full Text Available High frequency measurements of trifluoromethane (HFC-23, CHF3, a potent hydrofluorocarbon greenhouse gas, largely emitted to the atmosphere as a by-product of the production of the hydrochlorofluorocarbon HCFC-22 (CHClF2, at five core stations of the Advanced Global Atmospheric Gases Experiment (AGAGE network, combined with measurements on firn air, old Northern Hemisphere air samples and Cape Grim Air Archive (CGAA air samples, are used to explore the current and historic changes in the atmospheric abundance of HFC-23. These measurements are used in combination with the AGAGE 2-D atmospheric 12-box model and a Bayesian inversion methodology to determine model atmospheric mole fractions and the history of global HFC-23 emissions. The global modelled annual mole fraction of HFC-23 in the background atmosphere was 28.9 ± 0.6 pmol mol−1 at the end of 2016, representing a 28 % increase from 22.6 ± 0.4 pmol mol−1 in 2009. Over the same time frame, the modelled mole fraction of HCFC-22 increased by 19 % from 199 ± 2 to 237 ± 2 pmol mol−1. However, unlike HFC-23, the annual average HCFC-22 growth rate slowed from 2009 to 2016 at an annual average rate of −0.5 pmol mol−1 yr−2. This slowing atmospheric growth is consistent with HCFC-22 moving from dispersive (high fractional emissions to feedstock (low fractional emissions uses, with HFC-23 emissions remaining as a consequence of incomplete mitigation from all HCFC-22 production.Our results demonstrate that, following a minimum in HFC-23 global emissions in 2009 of 9.6 ± 0.6, emissions increased to a maximum in 2014 of 14.5 ± 0.6 Gg yr−1 and then declined to 12.7 ± 0.6 Gg yr−1 (157 Mt CO2 eq. yr−1 in 2016. The 2009 emissions minimum is consistent with estimates based on national reports and is likely a response to the implementation of the Clean Development Mechanism (CDM to mitigate HFC-23 emissions by

  2. Recent increases in the atmospheric growth rate and emissions of HFC-23 (CHF3) and the link to HCFC-22 (CHClF2) production

    Science.gov (United States)

    Simmonds, Peter G.; Rigby, Matthew; McCulloch, Archie; Vollmer, Martin K.; Henne, Stephan; Mühle, Jens; O'Doherty, Simon; Manning, Alistair J.; Krummel, Paul B.; Fraser, Paul J.; Young, Dickon; Weiss, Ray F.; Salameh, Peter K.; Harth, Christina M.; Reimann, Stefan; Trudinger, Cathy M.; Steele, L. Paul; Wang, Ray H. J.; Ivy, Diane J.; Prinn, Ronald G.; Mitrevski, Blagoj; Etheridge, David M.

    2018-03-01

    High frequency measurements of trifluoromethane (HFC-23, CHF3), a potent hydrofluorocarbon greenhouse gas, largely emitted to the atmosphere as a by-product of the production of the hydrochlorofluorocarbon HCFC-22 (CHClF2), at five core stations of the Advanced Global Atmospheric Gases Experiment (AGAGE) network, combined with measurements on firn air, old Northern Hemisphere air samples and Cape Grim Air Archive (CGAA) air samples, are used to explore the current and historic changes in the atmospheric abundance of HFC-23. These measurements are used in combination with the AGAGE 2-D atmospheric 12-box model and a Bayesian inversion methodology to determine model atmospheric mole fractions and the history of global HFC-23 emissions. The global modelled annual mole fraction of HFC-23 in the background atmosphere was 28.9 ± 0.6 pmol mol-1 at the end of 2016, representing a 28 % increase from 22.6 ± 0.4 pmol mol-1 in 2009. Over the same time frame, the modelled mole fraction of HCFC-22 increased by 19 % from 199 ± 2 to 237 ± 2 pmol mol-1. However, unlike HFC-23, the annual average HCFC-22 growth rate slowed from 2009 to 2016 at an annual average rate of -0.5 pmol mol-1 yr-2. This slowing atmospheric growth is consistent with HCFC-22 moving from dispersive (high fractional emissions) to feedstock (low fractional emissions) uses, with HFC-23 emissions remaining as a consequence of incomplete mitigation from all HCFC-22 production.Our results demonstrate that, following a minimum in HFC-23 global emissions in 2009 of 9.6 ± 0.6, emissions increased to a maximum in 2014 of 14.5 ± 0.6 Gg yr-1 and then declined to 12.7 ± 0.6 Gg yr-1 (157 Mt CO2 eq. yr-1) in 2016. The 2009 emissions minimum is consistent with estimates based on national reports and is likely a response to the implementation of the Clean Development Mechanism (CDM) to mitigate HFC-23 emissions by incineration in developing (non-Annex 1) countries under the Kyoto Protocol. Our derived cumulative

  3. (Vapour + liquid) equilibria of the {1,1-difluoroethane (HFC-152a) + n-butane (HC-600)} system

    International Nuclear Information System (INIS)

    Im, Jihoon; Lee, Gangwon; Lee, Yong-Jin; Kim, Hwayong

    2007-01-01

    Binary (vapour + liquid) equilibrium data were obtained for the {1,1-difluoroethane (HFC-152a) + n-butane (HC-600)} system at temperatures from 313.15 K to 363.15 K. These experiments were carried out with a circulating-type apparatus with on-line gas chromatography. The experimental data were correlated well by Peng-Robinson equation of state using the Wong-Sandler mixing rules. This system shows positive azeotropic phase behaviour

  4. Measurements of HFC-134a and HCFC-22 in groundwater and unsaturated-zone air: implications for HFCs and HCFCs as dating tracers

    Science.gov (United States)

    Haase, Karl B.; Busenberg, Eurybiades; Plummer, Niel; Casile, Gerolamo; Sanford, Ward E.

    2014-01-01

    A new analytical method using gas chromatography with an atomic emission detector (GC–AED) was developed for measurement of ambient concentrations of hydrochlorofluorocarbons (HCFCs) and hydrofluorocarbons (HFCs) in soil, air, and groundwater, with the goal of determining their utility as groundwater age tracers. The analytical detection limits of HCFC-22 (difluorochloromethane, CHClF2) and HFC-134a (1,2,2,2-tetrafluoroethane, C2H2F4) in 1 L groundwater samples are 4.3 × 10− 1 and 2.1 × 10− 1 pmol kg− 1, respectively, corresponding to equilibrium gas-phase mixing ratios of approximately 5–6 parts per trillion by volume (pptv). Under optimal conditions, post-1960 (HCFC-22) and post-1995 (HFC-134a) recharge could be identified using these tracers in stable, unmixed groundwater samples. Ambient concentrations of HCFC-22 and HFC-134a were measured in 50 groundwater samples from 27 locations in northern and western parts of Virginia, Tennessee, and North Carolina (USA), and 3 unsaturated-zone profiles were collected in northern Virginia. Mixing ratios of both HCFC-22 and HFC-134a decrease with depth in unsaturated-zone gas profiles with an accompanying increase in CO2 and loss of O2. Apparently, ambient concentrations of HCFC-22 and HFC-134a are readily consumed by methanotrophic bacteria under aerobic conditions in the unsaturated zone. The results of this study indicate that soils are a sink for these two greenhouse gases. These observations contradict the previously reported results from microcosm experiments that found that degradation was limited above-ambient HFC-134a. The groundwater HFC and HCFC concentrations were compared with concentrations of chlorofluorocarbons (CFCs, CFC-11, CFC-12, CFC-113) and sulfur hexafluoride (SF6). Nearly all samples had measured HCFC-22 or HFC-134a that were below concentrations predicted by the CFCs and SF6, with many samples showing a complete loss of HCFC-22 and HFC-134a. This study indicates that HCFC-22 and HFC-134

  5. Choked flow mechanism of HFC-134a flowing through short-tube orifices

    Energy Technology Data Exchange (ETDEWEB)

    Nilpueng, Kitti; Wongwises, Somchai [Fluid Mechanics, Thermal Engineering and Multiphase Flow Research Lab (FUTURE), Department of Mechanical Engineering, King Mongkut' s University of Technology Thonburi, Bangmod, Bangkok (Thailand)

    2011-02-15

    This paper is a continuation of the author's previous work. New experimental data on the occurrence of choked flow phenomenon and mass flow rate of HFC-134a inside short-tube orifices under choked flow condition are presented. Short-tube orifices diameters ranging from 0.406 mm to 0.686 mm with lengths ranging from 1 mm to 3 mm which can be applied to a miniature vapour-compression refrigeration system are examined. The experimental results indicated that the occurrence of choked flow phenomena inside short-tube orifices is different from that obtained from short-tube orifice diameters of greater than 1 mm, which are typically used in air-conditioner. The beginning of choked flow is dependent on the downstream pressure, degree of subcooling, and length-to-diameter ratio. Under choked flow condition, the mass flow rate is greatly varied with the short-tube orifice dimension, but it is slightly affected by the operating conditions. A correlation of mass flow rate through short-tube orifices is proposed in terms of the dimensionless parameters. The predicted results show good agreement with experimental data with a mean deviation of 4.69%. (author) transfer coefficient was also proposed. (author)

  6. Uptake and disposition of 1,1-difluoroethane (HFC-152a) in humans.

    Science.gov (United States)

    Ernstgård, Lena; Sjögren, Bengt; Dekant, Wolfgang; Schmidt, Tobias; Johanson, Gunnar

    2012-02-25

    The aim of this study was to determine the toxicokinetics of inhaled 1,1-difluoroethane (HFC-152a) in humans. Healthy volunteers were exposed to 0, 200 or 1000 ppm 1,1-difluoroethane for 2h at light exercise in an exposure chamber. Capillary blood, urine and exhaled air were sampled up to 22 h post-exposure and analyzed for 1,1-difluoroethane. Fluoride and other potential metabolites were analyzed in urine. Symptoms of irritation and central nervous system effects were rated and inflammatory markers were analyzed in blood. Within a few minutes of exposure to 200 and 1000 ppm, 1,1-difluoroethane increased rapidly in blood and reached average levels of 7.4 and 34.3 μM, respectively. The post-exposure decreases in blood were fast and parallel to those in exhaled air. The observed time courses in blood and breath agreed well with those obtained with the PBPK model. The PBPK simulations indicate a net uptake during exposure to 1000 ppm of 6.6 mmol (6.7%) which corresponds to the amount exhaled post-exposure. About 20 μmol excess fluoride (0.013% of inhaled 1,1-difluoroethane on a molar basis) was excreted in urine after exposure to 1000 ppm, compared to control. No fluorine-containing metabolites were detected in urine. Symptom ratings and changes in inflammatory markers revealed no exposure-related effects. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  7. Investigation of two-phase thermosyphon performance filled with modern HFC refrigerants

    Science.gov (United States)

    Gorecki, Grzegorz

    2018-02-01

    Two-phase closed thermosyphons (TPCTs) are widely utilized as heat exchanger elements in waste heat recovery systems and as passive heating/cooling devices. They are popular because of their high thermal conductivity, simple construction and reliability. Previous researches indicate that refrigerants are performing better than typical TPCT working fluids like deionized water or alcohols in the low temperature range. In the present study three HFC (Hydrofluorocarbons) refrigerants were tested: R134a, R404A and R407C. The total length of the investigated TPCT is 550 mm with equal length (245 mm) condenser and evaporator sections. Its outer diameter is 22 mm with 1 mm wall thickness. The evaporator section was heated by hot water with varying inlet temperature by 5 K step in the range of 288 K - 323 K. The condenser was cooled by cold water with inlet temperature kept at a constant value of 283 K. It was found that using R134a and R404A as working fluids heat transfer rates are the highest. For both refrigerants 10% is optimal filling ratio. They can be utilized interchangeably because the differences between their throughputs are within uncertainty bands. R407C performance was 50% lower. Other disadvantages of using this refrigerant are relatively high working pressures and higher optimal filling ratio (30%).

  8. Indirect phase transition of TiC, ZrC, and HfC crystal structures

    Energy Technology Data Exchange (ETDEWEB)

    Abavare, Eric K.K.; Dodoo, Samuel N.A. [Department of Physics, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana); Uchida, Kazuyuki; Oshiyama, Atsushi [Department of Applied Physics, The University of Tokyo, Hongo, Tokyo (Japan); Nkurumah-Buandoh, George K.; Yaya, Abu [Department of Physics, University of Ghana, Legon (Ghana)

    2016-06-15

    We have performed first-principles calculations to analyze the electronic structures, static, and dynamical structural stabilities of the pressure-induced phase transformation of refractory compounds (transition-metal carbides) from NaCl-type (B1) to CsCl-type (B2) via zinc-blende phase using the plane-wave pseudopotential approach in the framework of the generalized gradient approximation (GGA) for the exchange and correlation functional. The ground-state properties, equilibrium lattice constant, bulk moduli, and band structures are determined for the stoichiometry of the compounds and compared with known experimental and theoretical values. We find that the phase-transition pressure for the indirect phase transition from B1→B2 via zinc-blende structure is about 17-fold for TiC, 12-fold for both ZrC and HfC, respectively, when compared with the direct phase transition. Calculated phonon instability exists for the CsCl-B2 phase, which can prevent the structures from forming and contrary to the zinc-blende and the NaCl-B1 phases. The band dispersion and electronic density of states for B1 and B2 crystal phases were explored and found to indicate metallic character in contrast with the zinc-blende phase, which has a pseudogap opening in the bandgap region suggesting a semiconducting property and also a frequency gap in the phonon spectrum. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Atmospheric observations for quantifying emissions of point-source synthetic greenhouse gases (CF4, NF3 and HFC-23)

    Science.gov (United States)

    Arnold, Tim; Manning, Alistair J.; Li, Shanlan; Kim, Jooil; Park, Sunyoung; Fraser, Paul J.; Mitrevski, Blagoj; Steele, L. Paul; Krummel, Paul B.; Mühle, Jens; Weiss, Ray F.

    2016-04-01

    The fluorinated species carbon tetrafluoride (CF4; PFC-14), nitrogen trifluoride (NF3) and trifluoromethane (CHF3; HFC-23) are potent greenhouse gases with 100-year global warming potentials of 6,630, 16,100 and 12,400, respectively. Unlike the majority of CFC-replacement compounds that are emitted from fugitive and mobile emission sources, these gases are largely emitted from large single point sources - semiconductor manufacturing facilities (all three), aluminium smelting plants (CF4) and chlorodifluoromethane factories (HFC-23). In this work we show the potential for atmospheric measurements to understand regional sources of these gases and to highlight emission 'hotspots'. We target our analysis on measurements from two Advanced Global Atmospheric Gases Experiment (AGAGE) long term monitoring sites that are particularly sensitive to regional emissions of these gases: Gosan on Jeju Island in the Republic of Korea and Cape Grim on Tasmania in Australia. These sites measure CF4, NF3 and HFC-23 alongside a suite of greenhouse and stratospheric ozone depleting gases every two hours using automated in situ gas-chromatography mass-spectrometry instrumentation. We couple each measurement to an analysis of air history using the regional atmospheric transport model NAME (Numerical Atmospheric dispersion Modelling Environment) driven by 3D meteorology from the Met Office's Unified Model, and use a Bayesian inverse method (InTEM - Inversion Technique for Emission Modelling) to calculate yearly emission changes over a decade (2005-2015) at high spatial resolution. At present these gases make a small contribution to global radiative forcing, however, given that their impact could rise significantly and that point sources of such gases can be mitigated, atmospheric monitoring could be an important tool for aiding emissions reduction policy.

  10. HFO1234ze(E) And HFC134a Flow Boiling Inside a 4mm Horizontal Smooth Tube

    OpenAIRE

    Longo, Giovanni A.; Mancin, Simone; Righetti, Giulia; Zilio, Claudio

    2016-01-01

    Nowadays, the substitution of HFC134a with low GWP refrigerants is one of the most important challenge for refrigeration and air conditioning. The possible substitutes include natural refrigerants, such as HC600 (Butane) and HC600a (Isobutane), and also synthetic refrigerants, such as HFO1234yf and HFO1234ze(E). The HC refrigerants exhibit very low GWP, 3 and 4 HC600a and HC600 respectively, good thermodynamic and transport properties, and pressure and volumetric performance very similar to H...

  11. Substituting HCFC-22 for HFC-410A: an environmental impact trade-off between the ozone depletion and climate change regimes

    Science.gov (United States)

    Wang, Z.; Fang, X.; Zhang, J.

    2015-12-01

    After the phase-out of hydrochlorofluorocarbons (HCFCs) as ozone-depleting substances pursuant to the requirements of the Montreal Protocol, hydrofluorocarbons (HFCs) are worldwide used as substitutes although the bulk of them are potent greenhouse gases (GHGs). Therefore, the alternation may bring side effect on global climate change. The trade-off of its environmental impacts between the ozone depletion and climate change regimes necessitates a quantification of the past and future consumption and emissions of both the original HCFCs and their alternative HFCs. Now a dilemma arise in China's RAC industry that HCFC-22, which has an ozone-depleting potential (ODP) of 0.055, has been replaced by HFC-410A, which is a blended potent GHG from respective 50% HFC-32 and HFC-125 with a global warming potential (GWP) of 1923.5. Here, we present our results of estimates of consumption and emissions of HCFC-22 and HFC-410A from 1994 to 2050. Historic emissions of HCFC-22 contributed to global total HCFCs by 4.0% (3.0%-5.6%) ODP-weighted. Projection under a baseline scenario shows future accumulative emissions of HFC-410A make up 5.9%-11.0% of global GWP-weighted HFCs emissions, and its annual contribution to national overall CO2 emissions can be 5.5% in 2050. This makes HCFC-22 and HFC-410A emissions of significant importance in ozone depletion and climate change regimes. Two mitigation scenarios were set to assess the mitigation performance under the North America Proposal and an accelerated schedule. In practice of international environmental agreement, "alternative to alternative" should be developed to avoid regrettable alternations.

  12. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of HFC-23 destruction technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. HFC-23 hakai gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-01

    HFC-23 is produced as a by-product during HCFC-22 manufacturing (produced at by-production rate of about 2%, whereas the reaction control has limitation in reducing the production). This is one of the substances subjected to the greenhouse effect gas reduction in the climate change framework treaty. This paper describes the achievements in 1998 on developing the HFC-23 destruction technology. High-temperature pyrolysis decomposes the substance into HF and CO2, which are given absorption treatment by water and alkali to make them harmless, and are recovered finally as calcium fluoride. An equipment having the treatment capability of 195 kg/h was constructed. Design was made on a facility capable of treating fluorine containing waste water at 3 t/h at maximum. Utilities consumed in a factory (industrial water, acids for neutralization, and alkali) are used effectively to identify the effect of reducing the treatment cost. Discussions were given from the safety aspect on facilities to prevent leakage of fluorine containing waste water being a harmful substance. Fabrication was executed on a full-size treatment testing equipment that can utilize the utilities in the factory effectively, and trial equipment operation was performed to arrange the system prepared toward the future tests and researches. (NEDO)

  13. Global and regional emissions estimates of 1,1-difluoroethane (HFC-152a, CH[subscript 3]CHF[subscript 2]) from in situ and air archive observations

    OpenAIRE

    Prinn, Ronald G.

    2015-01-01

    High frequency, in situ observations from 11 globally distributed sites for the period 1994–2014 and archived air measurements dating from 1978 onward have been used to determine the global growth rate of 1,1-difluoroethane (HFC-152a, CH[subscript 3]CHF[subscript 2]). These observations have been combined with a range of atmospheric transport models to derive global emission estimates in a top-down approach. HFC-152a is a greenhouse gas with a short atmospheric lifetime of about 1.5 years. Si...

  14. Emissions of CO2, CO, NOx, HC, PM, HFC-134a, N2O and CH4 from the global light duty vehicle fleet

    Directory of Open Access Journals (Sweden)

    Timothy J. Wallington

    2008-04-01

    Full Text Available Vehicles emit carbon dioxide (CO2, carbon monoxide (CO, nitrogen oxides (NOx, hydrocarbons (HC, particulate matter (PM, hydrofluorocarbon 134a (HFC-134a, methane (CH4, and nitrous oxide (N2O. An understanding of these emissions is needed in discussions of climate change and local air pollution issues. To facilitate such discussions an overview of past, present, and likely future emissions from light duty vehicles is presented. Emission control technologies have reduced the emissions of CO, VOCs, PM, HFC-134a, CH4, and N2O from modern vehicles to very low levels.

  15. FPGAs Emulate Microprocessors-A Successful Case for HFC NPP Digital I and C Upgrade

    International Nuclear Information System (INIS)

    Hsu, Allen; Crow, Ivan; Reese, Carl; Kim, Jong; Yang, Steve

    2014-01-01

    upgrade and that are consistent with US NRC regulatory requirements and industrial standards are presented. Then hardware and software requirements including interfaces for replacing the existing microprocessor-based controllers with FPGA-based components are described. Next, HFC FPGA design philosophy and architecture for emulating Intel 8085 Microprocessor is described. Finally, the experience, benefits, and recommendations using FPGAs to emulate microprocessors for applications in the nuclear safety digital I and C upgrades as well as for new builds are summarized and discussed

  16. FPGAs Emulate Microprocessors-A Successful Case for HFC NPP Digital I and C Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Allen; Crow, Ivan; Reese, Carl; Kim, Jong; Yang, Steve [Doosan HF Controls Corp, Carrollton (United States)

    2014-08-15

    upgrade and that are consistent with US NRC regulatory requirements and industrial standards are presented. Then hardware and software requirements including interfaces for replacing the existing microprocessor-based controllers with FPGA-based components are described. Next, HFC FPGA design philosophy and architecture for emulating Intel 8085 Microprocessor is described. Finally, the experience, benefits, and recommendations using FPGAs to emulate microprocessors for applications in the nuclear safety digital I and C upgrades as well as for new builds are summarized and discussed.

  17. An experimental investigation on the substitution of HFC134a with HFO1234YF in a domestic refrigerator

    International Nuclear Information System (INIS)

    Aprea, Ciro; Greco, Adriana; Maiorino, Angelo

    2016-01-01

    Highlights: • An experimental comparison between R134A and HFO1234YF is presented. • A domestic refrigerator made to work with R134A is analysed. • The annual energy consumptions of the device are reported. • The energy saving achievable after the drop-in is evaluated. - Abstract: The latest international regulations on the reduction of greenhouse gases are strongly redesigning the scenario of use of refrigerants, gradually eliminating the possibility of employing the HFCs. Among all sectors of refrigeration, one of the most affected by these restrictions is the domestic refrigeration. Although for it have been suggested some solutions, such as the construction of household refrigerator operating with the hydrocarbons, there remains the need to find a substitute for HFC134a. In particular, the substitution may involve both existing machines and already in operation, which cannot be loaded with hydrocarbons, and new devices. With the aim of finding a simple implementation solution, in the present work, it is reported an experimental investigation carried out on a domestic refrigerator designed and built to operate with HFC134a and for which a drop-in with HFO1234yf has been realised. The experimentation has been addressed so as to highlight the behaviour of the system as a result of the drop-in, with a particular interest in the energy performance variation. A slight energy saving has been recorded with HFO1234yf, and an improving of the cooling capacity has been noticed.

  18. Viscosity measurements and correlations of binary mixtures: 1,1,1,2-tetrafluoroethane (HFC-134a)+tetraethylene glycol dimethylether (TEGDME)

    DEFF Research Database (Denmark)

    Monsalvo, Matias Alfonso; Baylaucq, A.; Reghem, P.

    2005-01-01

    .15-373.15 K. The measurements have been carried out with a failing body viscometer for four molar fractions x(1) =(0.28, 0.44, 0.63 and 0.88). The density values of this system were interpolated from previous results obtained at the laboratory. All of the available viscosity data, including pure HFC-134a...

  19. Global and regional emissions estimates of 1,1-difluoroethane (HFC-152a, CH3CHF2) from in situ and air archive observations

    Science.gov (United States)

    Simmonds, P. G.; Rigby, M.; Manning, A. J.; Lunt, M. F.; O'Doherty, S.; McCulloch, A.; Fraser, P. J.; Henne, S.; Vollmer, M. K.; Mühle, J.; Weiss, R. F.; Salameh, P. K.; Young, D.; Reimann, S.; Wenger, A.; Arnold, T.; Harth, C. M.; Krummel, P. B.; Steele, L. P.; Dunse, B. L.; Miller, B. R.; Lunder, C. R.; Hermansen, O.; Schmidbauer, N.; Saito, T.; Yokouchi, Y.; Park, S.; Li, S.; Yao, B.; Zhou, L. X.; Arduini, J.; Maione, M.; Wang, R. H. J.; Ivy, D.; Prinn, R. G.

    2016-01-01

    High frequency, in situ observations from 11 globally distributed sites for the period 1994-2014 and archived air measurements dating from 1978 onward have been used to determine the global growth rate of 1,1-difluoroethane (HFC-152a, CH3CHF2). These observations have been combined with a range of atmospheric transport models to derive global emission estimates in a top-down approach. HFC-152a is a greenhouse gas with a short atmospheric lifetime of about 1.5 years. Since it does not contain chlorine or bromine, HFC-152a makes no direct contribution to the destruction of stratospheric ozone and is therefore used as a substitute for the ozone depleting chlorofluorocarbons (CFCs) and hydrochlorofluorocarbons (HCFCs). The concentration of HFC-152a has grown substantially since the first direct measurements in 1994, reaching a maximum annual global growth rate of 0.84 ± 0.05 ppt yr-1 in 2006, implying a substantial increase in emissions up to 2006. However, since 2007, the annual rate of growth has slowed to 0.38 ± 0.04 ppt yr-1 in 2010 with a further decline to an annual average rate of growth in 2013-2014 of -0.06 ± 0.05 ppt yr-1. The annual average Northern Hemisphere (NH) mole fraction in 1994 was 1.2 ppt rising to an annual average mole fraction of 10.1 ppt in 2014. Average annual mole fractions in the Southern Hemisphere (SH) in 1998 and 2014 were 0.84 and 4.5 ppt, respectively. We estimate global emissions of HFC-152a have risen from 7.3 ± 5.6 Gg yr-1 in 1994 to a maximum of 54.4 ± 17.1 Gg yr-1 in 2011, declining to 52.5 ± 20.1 Gg yr-1 in 2014 or 7.2 ± 2.8 Tg-CO2 eq yr-1. Analysis of mole fraction enhancements above regional background atmospheric levels suggests substantial emissions from North America, Asia, and Europe. Global HFC emissions (so called "bottom up" emissions) reported by the United Nations Framework Convention on Climate Change (UNFCCC) are based on cumulative national emission data reported to the UNFCCC, which in turn are based on

  20. Oxidation behavior of TiC, ZrC, and HfC dispersed in oxide matrices

    International Nuclear Information System (INIS)

    Arun, R.; Subramanian, M.; Mehrotra, G.M.

    1990-01-01

    The oxidation behavior of hot pressed TiC-Al 2 O 3 , TiC-ZrO 2 , ZrC-ZrO 2 , and HfC-HfO 2 composites has been investigated at 1273 K. The oxidation of TiC, ZrC, and HfC in hot-pressed composites containing ZrO 2 and HfO 2 has been found to be extremely rapid. The kinetics of oxidation of TiC and a 90 wt% TiC-Al 2 O 3 composite appear to be faster compared to that of pure TiC. X-ray diffraction results for hot-pressed ZrC-HfO 2 and HfC-HfO 2 composites indicate partial stabilization of tetragonal ZrO 2 and HfO 2 phases in these composites

  1. Potential energy and dipole moment surfaces for HF@C60: Prediction of spectral and electric response properties

    Science.gov (United States)

    Kalugina, Yulia N.; Roy, Pierre-Nicholas

    2017-12-01

    We present a five-dimensional potential energy surface (PES) for the HF@C60 system computed at the DF-LMP2/cc-pVTZ level of theory. We also calculated a five-dimensional dipole moment surface (DMS) based on DFT(PBE0)/cc-pVTZ calculations. The HF and C60 molecules are considered rigid with bond length rHF = 0.9255 Å (gas phase ground rovibrational state geometry). The C60 geometry is of Ih symmetry. The ab initio points were fitted to obtain a PES in terms of bipolar spherical harmonics. The minimum of the PES corresponds to a geometry where the center of mass of HF is located 0.11 Å away from the center of the cage with an interaction energy of -6.929 kcal/mol. The DMS was also represented in terms of bipolar spherical harmonics. The PES was used to calculate the rotation-translation bound states of HF@C60, and good agreement was found relative to the available experimental data [A. Krachmalnicoff et al., Nat. Chem. 8, 953 (2016)] except for the splitting of the first rotational excitation levels. We propose an empirical adjustment to the PES in order to account for the experimentally observed symmetry breaking. The form of that effective PES is additive. We also propose an effective Hamiltonian with an adjusted rotational constant in order to quantitatively reproduce the experimental results including the splitting of the first rotational state. We use our models to compute the molecular volume polarizability of HF confined by C60 and obtain good agreement with experiment.

  2. High-pressure viscosity behavior of x 1,1,1,2-tetrafluoroethane (HFC-134a)+(1-x) triethylene glycol dimethylether (TriEGDME) mixtures: Measurements and modeling

    DEFF Research Database (Denmark)

    Monsalvo, Matias Alfonso; Baylaucq, A.; Cisneros, Sergio

    2006-01-01

    fractions x(HFC) = 0.3427 and 0.5940 (a total of 100 experimental values). Since lubricants and refrigerants are in two different thermodynamic states at atmospheric pressure and ambient temperature, an especially designed falling-body viscometer has been used to perform the measurements. The data obtained...... with a physical and theoretical background, such as the hard-sphere scheme, the free-volume model, and the friction theory....

  3. Heat transfer during condensation of HFC-134a and R-404A inside of a horizontal smooth and micro-fin tube

    Energy Technology Data Exchange (ETDEWEB)

    Sapali, S N [Govt. College of Engineering, Department of Mechanical Engineering, Shivaji Nagar, Pune, Maharashtra 411 005 (India); Patil, Pradeep A [AISSMS College of Engineering, Pune University, Mechanical Engineering Department, Kennedy Road, Near R.T.O., Pune, Maharashtra 411 001 (India)

    2010-11-15

    In recent small and medium capacity refrigeration systems, the condenser tubes are provided with micro-fins from inside. The vapour refrigerant at the compressor outlet and the condenser inlet is in superheat state. As it advances in the condenser it is in two phases and at the outlet it is in sub cooled liquid. The heat transfer coefficient (HTC) during condensation of HFC-134a and R-404A in a smooth (8.56 mm ID) and micro-fin tubes (8.96 mm ID) are experimentally investigated. Different from previous studies, the present experiments are performed for various condensing temperatures, with superheating and sub cooling and using hermetically sealed compressor. The test runs are done at average saturated condensing temperatures ranging from 35 C to 60 C. The mass fluxes are between 90 and 800 kg m{sup -2} s{sup -1}. The experimental results indicate that the average HTC increases with mass flux but decreases with increasing condensing temperature for both smooth and micro-fin tubes. The average condensation HTCs of HFC-134a and R-404A for the micro-fin tubes were 1.5-2.5 and 1.3-2 times larger than that in smooth tube respectively. The HTCs for R-404A are less than that of HFC-134a. New correlations based on the data gathered during the experimentation for predicting condensation HTCs are proposed for wide range of operating conditions. (author)

  4. Power Optimization of Organic Rankine-cycle System with Low-Temperature Heat Source Using HFC-134a

    Energy Technology Data Exchange (ETDEWEB)

    Baik, Young Jin; Kim, Min Sung; Chang, Ki Chang; Lee, Young Soo; Ra, Ho Sang [Korea Institute of Energy Research, Daejeon (Korea, Republic of)

    2011-01-15

    In this study, an organic Rankine-cycle system using HFC-134a, which is a power cycle corresponding to a low temperature heat source, such as that for geothermal power generation, was investigated from the view point of power optimization. In contrast to conventional approaches, the heat transfer and pressure drop characteristics of the working fluid within the heat exchangers were taken into account by using a discretized heat exchanger model. The inlet flow rates and temperatures of both the heat source and the heat sink were fixed. The total heat transfer area was fixed, whereas the heat-exchanger areas of the evaporator and the condenser were allocated to maximize the power output. The power was optimized on the basis of three design parameters. The optimal combination of parameters that can maximize power output was determined on the basis of the results of the study. The results also indicate that the evaporation process has to be optimized to increase the power output.

  5. Global and regional emissions estimates of 1,1-difluoroethane (HFC-152a, CH3CHF2 from in situ and air archive observations

    Directory of Open Access Journals (Sweden)

    P. G. Simmonds

    2016-01-01

    Full Text Available High frequency, in situ observations from 11 globally distributed sites for the period 1994–2014 and archived air measurements dating from 1978 onward have been used to determine the global growth rate of 1,1-difluoroethane (HFC-152a, CH3CHF2. These observations have been combined with a range of atmospheric transport models to derive global emission estimates in a top-down approach. HFC-152a is a greenhouse gas with a short atmospheric lifetime of about 1.5 years. Since it does not contain chlorine or bromine, HFC-152a makes no direct contribution to the destruction of stratospheric ozone and is therefore used as a substitute for the ozone depleting chlorofluorocarbons (CFCs and hydrochlorofluorocarbons (HCFCs. The concentration of HFC-152a has grown substantially since the first direct measurements in 1994, reaching a maximum annual global growth rate of 0.84 ± 0.05 ppt yr−1 in 2006, implying a substantial increase in emissions up to 2006. However, since 2007, the annual rate of growth has slowed to 0.38 ± 0.04 ppt yr−1 in 2010 with a further decline to an annual average rate of growth in 2013–2014 of −0.06 ± 0.05 ppt yr−1. The annual average Northern Hemisphere (NH mole fraction in 1994 was 1.2 ppt rising to an annual average mole fraction of 10.1 ppt in 2014. Average annual mole fractions in the Southern Hemisphere (SH in 1998 and 2014 were 0.84 and 4.5 ppt, respectively. We estimate global emissions of HFC-152a have risen from 7.3 ± 5.6 Gg yr−1 in 1994 to a maximum of 54.4 ± 17.1 Gg yr−1 in 2011, declining to 52.5 ± 20.1 Gg yr−1 in 2014 or 7.2 ± 2.8 Tg-CO2 eq yr−1. Analysis of mole fraction enhancements above regional background atmospheric levels suggests substantial emissions from North America, Asia, and Europe. Global HFC emissions (so called “bottom up” emissions reported by the United Nations Framework Convention on Climate Change (UNFCCC

  6. EVALUASI PENGELOLAAN REFRIGERAN CFC, DAN HFC DENGAN MESIN 3R DAN UJI UNJUK KERJA MESIN PENDINGIN STUDI KASUS PADA BENGKEL AC MOBIL DI DENPASAR - BALI

    Directory of Open Access Journals (Sweden)

    I MADE RASTA

    2015-06-01

    Full Text Available CFC refrigerant has been known to be one of causes of ozone layer diminishing and HFC is one of green house gases contributing to global warming through the leak and synthetic refrigerant waste to environment. As a response to the ozone layer diminishment on stratosphere, UNEP, in 1981, through a negotiating process of international stages of development reserve the ozone layer through Wina Convention legalized in March 1985. It was then followed up with Montreal Protocol in September 1987 consisting supervision rules on producing, consuming, and treading ozone damaging materials. The government of Indonesia had ratified the convention through President Decree Number 23 Year 1999. The ozone layer reservation program implementation in Indonesia is facilitated by KLH. Governor of Bali issued Decree Number 523/04-B/HK/2010 on membership restructuring of ozone layer reservation and ozone damaging materials control team work in province of Bali. This research was done in 27 car AC service companies or workshop, which received grant of 3R engine in Denpasar, Bali. The research was dominantly focused on monitoring and evaluation, that is how car AC service company or workshop manage CFC/ R-12 and HFC/R-134a refrigerant at service time using 3R engine that refrigerant does not escape to atmostphere. Cooling machine work procedure test (COP was conducted in laboratory. Research result showed that car AC service company or workshop could manage CFC/ R-12 and HFC /R-l 34a eefctively ( 88,3%. The cooling engine work procedure using CFC /R-12 as the result of 3R engine recovery and recycel resulted in 2,435 while pure CFC/R-12 resulted in 2,54. There were differences in cooling engine work procedure to the use of pure CFC/R-12 refrigerant with that resulted by 3R engine with avarage difference 0,089 or 3,53%.

  7. Technical–economic analysis of including wind farms and HFC to solve hybrid TNEM–RPM problem in the deregulated environment

    International Nuclear Information System (INIS)

    Shayeghi, H.; Hashemi, Y.

    2014-01-01

    Highlights: • Capability of wind farms is contributed in the problem of hybrid TNEM–RPM. • Inclusion of HFC as a novel and versatile device to implement hybrid TNEM–RPM. • INSGA-II optimization and FDM method is applied to specify the best solution. • Simulation study is conducted on the real power system of Iran. - Abstract: This paper addresses a mathematical model for solving transmission network expansion management (TNEM) associated with reactive power management (RPM) in the presence of double-fed induction generator (DFIG) variable speed wind turbine and hybrid flow controller (HFC). According to this plan, the reactive power capability of DFIG wind turbine is gained and the constraints of deliverable power are derived for each operation point. Strong control capability of the HFC with controlling bus voltage and line power flow offers a great potential for solving many of the problems facing electric utilities. For a precise steady-state analysis of HFC, the injection model is considered which it is an adaptive model in steady-state analysis. The main goals of the proposed management strategy are to minimize investment cost, real power loss cost in transmission lines and voltage deviation and maximize voltage stability index and social benefit at the same time. A three-stage scheme has been developed for solving hybrid TNEM–RPM problem. In the beginning of the plan, it is assumed that all the reactive demands are acquired from local sources and an optimal transmission plan is specified. After transmission lines are constructed, in the second step, reactive power sources will be allocated to weak buses. In order to assess reliability of the system, EENS criterion is used. Due to multi-objective nature of the proposed management method, an improved non-dominated sorting genetic algorithm-II (INSGA-II) style is applied for an optimization procedure. Also, a decision making method based on fuzzy decision making (FDM) is used for finding the best

  8. Energy savings with the effect of magnetic field using R290/600a mixture as substitute for CFC12 and HFC134a

    Directory of Open Access Journals (Sweden)

    Mani Kolandavel

    2008-01-01

    Full Text Available This paper presents an experimental study on the replacement of CFC12 and HFC134a by the new R290/R600a refrigerant mixture as drop-in replacement refrigerant with and without the effect of magnetic field. Without any modification to the system components drop-in experimental tests were performed on a vapour compression refrigeration system with a reciprocating compressor, which was originally designed to operate with CFC12.The test results with no magnets showed that the refrigerant R290/R600a had 19.9-50.1% higher refrigerating capacity than R12 and 28.6-87.2% than R134a. The mixture R290/R600a consumed 6.8- -17.4% more energy than R12. The coefficient of performance of R290/R600a mixture increases from 3.9-25.1% than R12 at lower evaporating temperatures and 11.8-17.6% at higher evaporating temperatures. The effect of magnetic field force reduced the compressor energy consumption by 1.5-2.5% than with no magnets. The coefficient of performance of the system was higher in the range 1.5-2.4% with the effect of magnetic field force. The R290/600a (68/32 by wt.% mixture can be considered as an excellent alternative refrigerant for CFC12 and HFC134a systems.

  9. Evaluation of stratospheric age of air from CF4, C2F6, C3F8, CHF3, HFC-125, HFC-227ea and SF6; implications for the calculations of halocarbon lifetimes, fractional release factors and ozone depletion potentials

    Science.gov (United States)

    Leedham Elvidge, Emma; Bönisch, Harald; Brenninkmeijer, Carl A. M.; Engel, Andreas; Fraser, Paul J.; Gallacher, Eileen; Langenfelds, Ray; Mühle, Jens; Oram, David E.; Ray, Eric A.; Ridley, Anna R.; Röckmann, Thomas; Sturges, William T.; Weiss, Ray F.; Laube, Johannes C.

    2018-03-01

    In a changing climate, potential stratospheric circulation changes require long-term monitoring. Stratospheric trace gas measurements are often used as a proxy for stratospheric circulation changes via the mean age of air values derived from them. In this study, we investigated five potential age of air tracers - the perfluorocarbons CF4, C2F6 and C3F8 and the hydrofluorocarbons CHF3 (HFC-23) and HFC-125 - and compare them to the traditional tracer SF6 and a (relatively) shorter-lived species, HFC-227ea. A detailed uncertainty analysis was performed on mean ages derived from these new tracers to allow us to confidently compare their efficacy as age tracers to the existing tracer, SF6. Our results showed that uncertainties associated with the mean age derived from these new age tracers are similar to those derived from SF6, suggesting that these alternative compounds are suitable in this respect for use as age tracers. Independent verification of the suitability of these age tracers is provided by a comparison between samples analysed at the University of East Anglia and the Scripps Institution of Oceanography. All five tracers give younger mean ages than SF6, a discrepancy that increases with increasing mean age. Our findings qualitatively support recent work that suggests that the stratospheric lifetime of SF6 is significantly less than the previous estimate of 3200 years. The impact of these younger mean ages on three policy-relevant parameters - stratospheric lifetimes, fractional release factors (FRFs) and ozone depletion potentials - is investigated in combination with a recently improved methodology to calculate FRFs. Updates to previous estimations for these parameters are provided.

  10. On-site study of HCFC-22 substitution for HFC non-azeotropic blends (R417A, R422D) on a water chiller of a centralized HVAC system

    Energy Technology Data Exchange (ETDEWEB)

    Torrella, E.; Larumbe, J.A. [Polytechnic University of Valencia, Dep. of Applied Thermodynamics, Camino de Vera 14, E-46022 Valencia (Spain); Cabello, R.; Sanchez, D.; Llopis, R. [Jaume I University, Dep. of Mechanical Engineering and Construction, Campus de Riu Sec s/n, E-12071 Castellon (Spain)

    2010-09-15

    The European Regulation no 2037/2000 has banned manufacturing HCFC refrigerants from January 1st 2010, although its use is allowed up to 2015 if the fluids come from a recycling process. This situation creates the need for developing new working fluids to replace the HCFC in the refrigeration plants now in operation. Among all the HCFCs the R22 is the most widely used in a wide range of applications, especially in air conditioning. This work presents an on-site experimental study of the R22 replacement by two possible substitutes, the HFC-417A and the HFC-422D, in a water chiller in which the energy performance was evaluated. This chiller is part of the centralized HVAC system of a lecture room building at the Jaume I University of Castellon, Spain. This communication compares and analyses main operation parameters of the chiller when operating with each refrigerant in real conditions. (author)

  11. Experimental determination of Henry's law constants of difluoromethane (HFC-32 and the salting-out effects in aqueous salt solutions relevant to seawater

    Directory of Open Access Journals (Sweden)

    S. Kutsuna

    2017-06-01

    Full Text Available Gas-to-water equilibrium coefficients, KeqS (in M atm−1, of difluoromethane (CH2F2, a hydrofluorocarbon refrigerant (HFC-32, in aqueous salt solutions relevant to seawater were determined over a temperature (T range from 276 to 313 K and a salinity (S range up to 51 ‰ by means of an inert-gas stripping method. From the van't Hoff equation, the KeqS value in water, which corresponds to the Henry's law constant (KH, at 298 K was determined to be 0.065 M atm−1. The salinity dependence of KeqS (the salting-out effect, ln(KH∕KeqS, did not obey the Sechenov equation but was proportional to S0. 5. Overall, the KeqS(T value was expressed by ln(KeqS(T  =  −49.71 + (77.70 − 0.134  ×  S0. 5  ×  (100∕T + 19.14  ×  ln(T∕100. By using this equation in a lower-tropospheric semi-hemisphere (30–90 °S of the Advanced Global Atmospheric Gases Experiment (AGAGE 12-box model, we estimated that 1 to 4 % of the atmospheric burden of CH2F2 resided in the ocean mixed layer and that this percentage was at least 4 % in the winter; dissolution of CH2F2 in the ocean may partially influence estimates of CH2F2 emissions from long-term observational data of atmospheric CH2F2 concentrations.

  12. Compatibility of manufacturing process fluids with HFC refrigerants and ester lubricants. First draft of final report of part one and quarterly report of part two, January 3, 1994--November 30, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Cavestri, R.C. [Imagination Resources, Inc., Dublin, OH (United States)

    1994-11-01

    Included in this report is a compiled partial list of presently used processing materials in the air-conditioning and refrigeration industry and the manufacturers, intended uses, and applications of each. Also listed are the processing materials that have received final acceptance for this contracted study. An analytical methodology discussion is presented, including the final decision and the limitations of said methodology, as well as how to establish a level of confidence in observed immiscible material components in two 32 ISO VG polyolesters: (1) Mobil EAL Arctic 32; and (2) ICI Emkarate RL32H; both with HFC 134a refrigerant solutions.

  13. Surface Tension and p−ρ−T Data for 1,1,1,3,3-Pentafluorobutane (HFC-365mfc) and 1,1,1,2,2,3,3-Heptafluoro-3-methoxy-propane (HFE-347mcc)

    Czech Academy of Sciences Publication Activity Database

    Klomfar, Jaroslav; Součková, Monika; Pátek, Jaroslav

    2013-01-01

    Roč. 58, č. 8 (2013), s. 2316-2325 ISSN 0021-9568 R&D Projects: GA ČR GA101/09/0010 Institutional support: RVO:61388998 Keywords : surface tension * density * HFC-365mfc * HFE-347mcc Subject RIV: BJ - Thermodynamics Impact factor: 2.045, year: 2013

  14. Carl Linné sidemed Baltimaadega / Linda Kongo

    Index Scriptorium Estoniae

    Kongo, Linda, 1929-

    2007-01-01

    Carl Linné sidemed Baltimaadega on loonud tema õpilased ja õpilaste õpilased, kes siirdusid kuulama tema loenguid Uppsala Ülikoolis. Mitmed Baltimaadelt pärit loodusteadlased täiendasid end Linné õpilase Johann Andreas Murray juures. Tartu Ülikooli raamatukogus on hoiul üks Linné kiri

  15. Kei Apple Plant Thorn Synovitis | Nyamohanga | Annals of African ...

    African Journals Online (AJOL)

    Annals of African Surgery. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 12, No 2 (2015) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register · Download this PDF file. The PDF file you selected should load ...

  16. HFC perspectives in air-conditioning and refrigeration; Perspectives HFC en A/C et refrigeration

    Energy Technology Data Exchange (ETDEWEB)

    Fauvarque, P [ELF Atochem, Centre d` Application de Lavallois, 92 (France)

    1998-12-31

    This paper is a series of transparencies dealing with the development of substitutes for the replacement of the R-22 refrigerant in air-conditioning systems (R-134a, R-407C, R-410A), and in industrial refrigeration systems of agriculture and food industry (R-134a and R-404A). (J.S.)

  17. HFC perspectives in air-conditioning and refrigeration; Perspectives HFC en A/C et refrigeration

    Energy Technology Data Exchange (ETDEWEB)

    Fauvarque, P. [ELF Atochem, Centre d`Application de Lavallois, 92 (France)

    1997-12-31

    This paper is a series of transparencies dealing with the development of substitutes for the replacement of the R-22 refrigerant in air-conditioning systems (R-134a, R-407C, R-410A), and in industrial refrigeration systems of agriculture and food industry (R-134a and R-404A). (J.S.)

  18. Novel optical and structural properties of porous GaAs formed by anodic etching of n±GaAs in a HF:C_2H_5OH:HCl:H_2O_2:H_2O electrolyte: effect of etching time

    International Nuclear Information System (INIS)

    Naddaf, M.; Saad, M.

    2014-01-01

    Porous GaAs layers have been formed by anodic etching of n±type GaAs (10.0) substrates in a HF:C_2H_5OH:HCl:H_2O_2:H_2O electrolyte. A dramatic impact of etching time on the optical and structural properties of porous GaAs layer is demonstrated. The nano/micro-features of porous GaAs layers are revealed by scanning electron microscopy (SEM) imaging. Two-peak room temperature photoluminescence (PL), "blue-green"and "green-yellow", is obtained in all prepared porous GaAs samples. Proper adjustment of etching time is found to produce a white color layer, instead of the usual dark gray color of porous GaAs. This is found to cause vast enhancement in the intensity of the visible PL in porous GaAs layer. Chemical composition and structural characterization by means of X-ray photoelectron spectroscopic (XPS), X-ray diffraction (XRD), and micro-Raman spectroscopy, confirm that this layer is characterized with monoclinic β-Ga_2O_3 rich surface. Etching time induced-modification of structural and chemical properties of porous GaAs layer is discussed and correlated to its PL behavior. It is inferred that the "blue-green"PL in porous GaAs can be ascribed to different degrees of quantum confinement in GaAs nano crystallites, whereas, the "green-yellow"PL is highly influenced by the As_2O_3 and Ga_2O_3, content in the porous GaAs layer. In addition, the reflectance measurements reveal an anti-refection trend of behavior of porous GaAs layers in the spectral range (500-1,100 nm). (author)

  19. Atmospheric chemistry of CH3CHF2 (HFC-152a)

    DEFF Research Database (Denmark)

    Taketani, Fumikazu; Nakayama, Tomoki; Takahashi, Kenshi

    2005-01-01

    Smog chamber/Fourier transform infrared (FTIR) and laser-induced fluorescence (LIF) spectroscopic techniques were used to study the atmospheric degradation of CH3CHF2. The kinetics and products of the Cl(2P(3/2)) (denoted Cl) atom- and the OH radical-initiated oxidation of CH3CHF2 in 700 Torr of ...

  20. Thermal conductivity and PVT measurements of pentafluoroethane (refrigerant HFC-125)

    International Nuclear Information System (INIS)

    Tsvetkov, O.B.; Kletski, A.V.; Laptev, Yu.A.

    1995-01-01

    By means of the transient and steady-state coaxial cylinder methods, the thermal conductivity of pentfluoroethane was investigated at temperatures from 187 to 419 K and pressures from atmospheric to 6.0 MPa. The estimated uncertainty of the measured results is ± (2-3)%. The operation of the experimental apparatus was validated by measuring the thermal conductivity of R22 and R12. Determinations of the vapor pressure and PVT properties were carried out by a constant-volume apparatus for the temperature range 263 to 443 K, pressures up to 6 MPa, and densities from 36 to 516 kg m -3 . The uncertainties in temperature, pressure, and density are less than ±10 mK, ±0.08%, and ±0.1%, respectively

  1. Technical issues and a prospect of ICAI. Chiteki CAI no gijutsu kadai to kongo no doko

    Energy Technology Data Exchange (ETDEWEB)

    Otsuki, S. (Kyushu Institute of Technology, Kitakyushu (Japan))

    1992-12-10

    This paper explains technical issues and a prospect for intelligent computer assisted instruction (ICAI) which combines the intelligent tutoring system (ITS) with an open-ended (discovery) type education system. The paper summarizes the ITS characterized by modelling students based on error-origin diagnostic technologies; various functions that have been realized for the first time therefrom; different methods for error diagnosis and error-origin diagnosis; and criteria to evaluate these methods (evaluating generality, coverage, and tractability). The paper indicates that no complete diagnostic methods have been obtained according to these criteria, that, therefore, an issue of incompleteness in the student model still remains, and that unsolved issues in the ITS include some that exceed the framework of the ITS. Also mentioned in the paper are that the discovery type education system has a possibility of realizing an education with new quality, and that a new attempt is being performed to merge the ITS with the discovery type education system. 17 refs., 2 figs.

  2. IT Pealinnas oled sa õnnelik: meie-aasta / Priit Kongo, Aune Past

    Index Scriptorium Estoniae

    Kongo, Priit

    2016-01-01

    2015. aasta Eesti Suhtekorralduse Auhinna konkursil pälvis sisekommunikatsiooni preemia Net Group projekti eest "IT-pealinnas oled sa õnnelik: meie-aasta", mille eesmärgiks oli ettevõtte kui hea tööandja maine kujundamine. Žürii hinnangul oli tegemist loomingulise ja oskusliku lähenemisega sisekommunikatsioonile, millega ettevõte suutis loomulikul viisil kaasata oma töötajad firma tegevustesse ja kogukondadesse

  3. Les proverbLes proverbes dans Kongo Proverbs and the Origins of ...

    African Journals Online (AJOL)

    À la lumière des analyses du Dr Lisimba de certains proverbes de la famille bantu, nous découvrons l'importance que revêt la dynamique du langage offert par les proverbes. Ils peuvent ainsi être employés comme données dans la compilation de dictionnaires. En effet, pour la discipline des sciences du langage qu'est la ...

  4. Review on flight simulators (today and tomorrow); Flight simulatior no genjo to kongo

    Energy Technology Data Exchange (ETDEWEB)

    Komura, T. [Mitsubishi Precision Company Limited, Tokyo (Japan)

    2000-04-05

    This paper presents various flight simulators. A flight simulator is classified into that for R and D on aircraft and that for flight training according to its usage. As an example of the former, the general-purpose flight simulation test facility of National Aerospace Laboratory, Science and Technology Agency is in use for development of the STOL experimental aircraft 'Asuka' and simulation experiments for space development. A civil aircraft simulator simulating the interior of a cockpit, operation feeling of piloting devices, flight performance, dynamic characteristics, an engine system and a hydraulic system like a real aircraft is in wide use for training pilots. A fighter simulator for air force is used for training detection of enemy's aircraft by radar, and missile shooting. An antisubmarine patrol aircraft simulator is used for training detection of submarines by sonic detector and magnetic detector, and torpedo air-launching. For both simulators, real simulation of detection sensors or battle environment is required. (NEDO)

  5. Thermal insulator made of ultra fine particles of silica. Chobiryushi silica kei dannetsuzai

    Energy Technology Data Exchange (ETDEWEB)

    Eguchi, T.

    1991-05-30

    An overview was presented of properties and applications of thermal insulator made of ultra fine powder of silica, MICROTHERM. The thermal conductivity of MICROTHERM is as low as (1/3) - (1/4) of that of conventional thermal insulator, because it is mainly composed of fumed silica or aero gel and formed into porous structure. In addition, metal oxide of special particle size is added to it in order to reject the radiative heat. The thermal insulation property and the mechanical strength of MICROTHERM is not affected by a sudden change in temperature and moisture. The standard type of MICROTHERM can be used at a temperature up to 950 {degree}C, while the high temperature type MICROTHERM can stand a high temperature up to 1025 {degree}C for long period of time. The thickness of insulator can be reduced markedly by using MICROTHERM as compared with the use of conventional insulating materials. Many new products in which MICROTHERM is used came into market. New type kilt, Semi-cylindrical block, Super high temperature MICROTHERM are just a few examples. Variety of application and energy saving effect are attracting public attention. 11 figs.

  6. A survey of the fISh fauna of Transkei estuaries. Part 1. The Kei ...

    African Journals Online (AJOL)

    1985-01-16

    Jan 16, 1985 ... Cyrus 1983; Whitfield 1980a, 1980b; Whitfield & Blaber. 1978a, 1978b). Apart from occasional surveys (Blaber 1977; van der Elst 1978; Branch & Grindley ...... in the field and laboratory; the University of Transkei, the. Department of Agriculture and Forestry of the Republic of. Transkei and the Department of ...

  7. A survey of the fISh fauna of Transkei estuaries. Part 1. The Kei ...

    African Journals Online (AJOL)

    1985-01-16

    Jan 16, 1985 ... determine the species composition, seasonal distribution and abundance of fish ... distilled water. Temperature was measured using a mercury ..... dinoflagellates, blue-green algae and filamentous algae, all of which form part ...

  8. Polyphenols, ascorbate and antioxidant capacity of the Kei-apple (Dovyalis caffra) / Tersia de Beer

    OpenAIRE

    De Beer, Tersia

    2006-01-01

    There is a close relationship between the susceptibility to disease and nutritional state, in the sense that an adequate diet enhances resistance to disease. There is an increasing interest in this beneficial relationship among scientists, food manufacturers and consumers. The trend is moving towards functional foods and their specific health benefits. The results of numerous epidemiological studies and recent clinical trials provide consistent evidence that diets rich in fruit...

  9. La politique intellectuelle de Mvemba N'zinga (Dom Afonso 1er ...

    African Journals Online (AJOL)

    Le Kongo venait de rater un grand rendez-vous avec l'histoire. Mots-Clés: enseignement; élite intellectuelle; Bakongo; Mvemba N'zinga; Mbanza Kongo; Lisbonne; Mani Kongo Summary Taking advantage of the opportunities that he offered to the Portuguese monarch - consignment of missionaries, study of the young " ...

  10. Engineering characteristics of the improved soil by deep mixing method using coal ash; Sekitanbai wo riyoshita FGC shinso kongo shori koho ni yoru kairyodo no kogakuteki seishitsu to kongo no tenbo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Azuma, K; Watanabe, M [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    Japan currently produces about six million tons of coal ash annually, whose effective bulk utilization to earth engineering materials is an important issue of technological development. A slurry may be made by mixing the following three kinds of materials: fly ash discharged from power plants exclusively burning dust coal (F), gypsum generated as a by-product in a stack gas desulfurizing process (G), and commercially available cement (C). The slurry would be called an FGC slurry taking the first letters of the materials. This paper presents the results of laboratory tests, in-situ execution tests and centrifuge model testing on engineering characteristics of soils improved by the FGC slurry when the slurry is applied to implementing the deep mixing method. As a result, a large number of findings were obtained including the following matters: the FGC deep mixing method makes it possible to improve ground beds having small deformation coefficient with the same accuracy as in the cement-based deep mixing (CDM) method at strengths lower than 5 kg/cm {sup 2} which is difficult with the CDM method, not to speak of strengths equivalent to that is possible with the normal CDM method; and development of a ground bed with improved strength is possible without being governed by quality and kinds of the fly ash. 1 ref., 23 figs., 5 tabs.

  11. Anchoring of CoHFC nanoparticles on clinoptilolite for remedy of nuclear wastes

    Directory of Open Access Journals (Sweden)

    Yousefi Taher

    2017-01-01

    Full Text Available To improve the mechanical properties, the cobalt ferrocyanide precipitation was carried out on clinoptilolite as an inorganic polymer. In this work the combination of two important factors, stability (zeolite and high adsorption capacity (cobalt ferrocyanide were considered to improve the ions uptake ability of adsorbent. The modification was approved by X-ray diffraction, Scanning electronic microscopy and Fourier transform infrared spectroscopy. The modified zeolite was applied to remove Sr(II and Cs(I ions from aqueous solution in a batch system. The adsorption capacities of modified zeolite for Cs(I and Sr(II improved to 90 and 130 mgg-1, respectively. The Sr(II and Cs(I removal were investigated as a function of shaking time, pH, Sr(II, and Cs(I initial concentration and temperature. The experimental data were fitted well to Langmuir isotherm model for two sorbet metal ions. The time dependence sorption data showed that the uptakes of Cs(I and Sr(II were very rapid and apparent sorption equilibriums were achieved within 100 min of contact time. The kinetic experimental data were fitted to the pseudo-first order, pseudo-second order, the double exponential, Elovich and intraparticle diffusion models. The sorption rates and capacities as well as rate constants were evaluated.

  12. Exploring policy strategies for mitigating HFC emissions from refrigeration and air conditioning

    NARCIS (Netherlands)

    Hekkenberg, M.; Uiterkamp, Anton J. M. Schoot

    The growing demand for cooling throughout the world, possibly increased by global climate change, requires the implementation of policies to mitigate the related greenhouse gas (GHG) emissions from energy and refrigerant use in the refrigeration and air conditioning (RAC) sector. This article aims

  13. Survey of experimental data of thermophysical properties for difluoromethane (HFC-32)

    Czech Academy of Sciences Publication Activity Database

    Šifner, Oldřich

    1999-01-01

    Roč. 20, č. 6 (1999), s. 1653-1666 ISSN 0195-928X. [Symp.on Thermophysical Properties /13./. Colorado, 22.06.1999-27.06.1999] R&D Projects: GA ČR GA101/95/1369 Subject RIV: BJ - Thermodynamics Impact factor: 0.736, year: 1999

  14. Air-source heat pump carbon footprints: HFC impacts and comparison to other heat sources

    International Nuclear Information System (INIS)

    Johnson, Eric P.

    2011-01-01

    European governments see that heat pumps could reduce carbon emissions in space- and hot-water heating. EU's Renewable Energy Directive designates heat pumps as renewable - eligible for various subsidies - if their carbon footprints are below an implied, average threshold. This threshold omits carbon generated by manufacture and emission of a heat-pump's fluorocarbon refrigerant. It also omits the footprint of the heat pump's hardware. To see if these omissions are significant, this study calculated carbon footprints of representative, residential heat pumps in the UK. Three findings emerged. First, in relation to power generation, which accounts for most of a heat-pump's greenhouse-gas emissions, fluorocarbons add another 20% to the footprint. Second, at UK efficiencies a heat-pump footprint (in kg CO 2 e emitted per kWh delivered) is comparable or higher than footprints of gaseous fuels used in heating. It is lower than the footprint of heating oil and far lower than the footprints of solid fuels. Third, production and disposal of a heat pump's hardware is relatively insignificant, accounting for only 2-3% of the overall heat-pump footprint. Sensitivities to the results were assessed: key factors are footprint of electricity generation, F-gas composition and leak rates and type of wall construction. - Research highlights: → Refrigerant emissions add 20% to a UK air-source heat pump's carbon footprint. → This contribution is so far ignored by regulations. → UK heat pump footprints are comparable to those of gaseous fuels.

  15. Compatibility of lubricant additives with HFC refrigerants and synthetic lubricants. Final report, Part 1

    Energy Technology Data Exchange (ETDEWEB)

    Cavestri, R.C. [Imagination Resources, Inc., Dublin, OH (United States)

    1997-07-01

    Part one of this research provides manufacturers of components of air-conditioning and refrigeration equipment with a useful list of lubricant additives, sources, functional properties and chemical species. The list in part one is comprised of domestic lubricant additive suppliers and the results of a literature search that was specifically targeted for additives reported to be useful in polyolester chemistry.

  16. Mechanical stimulated reaction of metal/polymer mixed powders; Kinzoku/kobunshi kongo funmatsu no kikaiteki reiki hanno

    Energy Technology Data Exchange (ETDEWEB)

    Tobita, M.; Sakakibara, A.; Takemoto, Y. [Okayama University, Okayama (Japan). Faculty of Engineering; Iwabu, H. [Kurare Co. Ltd., Osaka (Japan)

    1999-12-15

    Mechanical grinding (MG) with mechanically stimulated reaction was performed on metal/polymer mixed powders. The starting materials used in this study were the metals of Mg, Ti and Mg{sub 2}Ni powders, arid polymer of PTFE, PVC and PE powders. The MG process was investigated using XRD, IR, SEM and TEM. According to XRD results, magnesium fluoride (MgF{sub 2}, TiF{sub 2}) and chloride (MgCl{sub 2}) were detected from MG products of the Mg/PTFE, Ti/PTFE and Mg/PVC blending systems, respectively. Explosive reaction was found during MG of both Mg/PTFE and Ti/PTFE. It was also confirmed by XRD results that the production of MgF{sub 2} had already been formed just before the explosive reaction in Mg/PTFE system. It was found from IR analysis that C-C single bond in the polymers, not only both in PTFE and PVC but also in PE, changed to double bond C=C. Hydrogen produced due to decomposition of PE on blending Mg{sub 2}Ni/PE was absorbed into C-Mg{sub 2}Ni-H as amorphous solutes. These mechanically stimulated reaction was powerful method for decomposition of engineering plastics. (author)

  17. Present status and future of various rubber materials. ; Asphalt. Kakushu gomu zairyo no genjo to kongo. ; Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Wakisaka, S. (Toa Doro Kogyo Co. Ltd., Tokyo (Japan))

    1991-12-15

    Asphalt is obtained at a rate of about 25 Kg per 1 Kl of oil and is produced at about 5 million tons per annum in Japan, 80 % of which is now used for the pavement of road. The purpose of this study is to examine the possibilities of developing new applications of asphalt to the anti-vibration, vibration-control and anti-noise materials, though its uses have already been diversified in fields other than for road paving, due to excellent performance regardless of cheap cost. In the paper, firstly, under a title of what is asphalt, the history, the composition and internal structure of asphalt were considered. Secondly, the dynamic characteristics of asphalt were considered. And lastly, under a title of the application of asphalt, examples of the application of asphalt to anti-noise materials were examined in the field of architecture, automobile and civil engineering respectively. Especially, in the field of civil engineering, improvements of flexibility and vibration-control by using the cement asphalt mortar (CAM) in the anti-vibration A-type slab track for railway, and also anti-noise and anti-vibration technologies applied to the road pavement body by using the ferrite asphalt were reviewed. 11 refs., 10 figs., 8 tabs.

  18. Islamic fundamentalism and future situations in Middle Eastern countries; Isuramu `genri shugi` to kongo no Chuto josei

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.

    1996-11-01

    This paper is a record of the special lecture given at the Institute of Energy Economics in July 1996. Significance of the Islamic fundamentalism, reasons for its rapid growth and proliferation, and measures thereto are described as plainly as in spoken lecture language. This fundamentalism is a borrowing from the Christianity terminology meaning the fundamentalism, which is referred to as returning to the original doctrine of the Bible or the Koran. Having become controlled by the industrialized countries in Europe and America is because of taking actions contrary to the ways instructed in the Koran (not, however, denying utilization of modern science and technology). The Islamic ideology feels symbolic victory in Third Middle East War, the Iranian Revolution, the war in Lebanon, and blocking the invasion of the Soviet Union into Afghanistan. The ideology takes actions to achieve political requests by entrusting the issues to religion, which are furthered by incompetence of the governments and poverty of people. In this sense, there should be roles to be played by Japan whose history of exploitation differs from that in Europe and America.

  19. Crude oil pricing in Asia and future problems; Asia no gen`yu pricing to kongo no kadai

    Energy Technology Data Exchange (ETDEWEB)

    Kato, T. [The Institute of Energy Economics, Tokyo (Japan)

    1997-01-30

    This paper describes pricing factors of crude oil for Asia and future problems. Price of the Middle East crude oil for Asia is determined by linking the spot price of Dubayy crude oil using as a marker. Factors affecting the pricing of marker crude oil include the information dispatching functions for prices of spot market and paper market of marker crude oil, the presence of competitive crude oil, and the correlation between market of oil products and price of crude oil. The paper market of Dubayy crude oil with a small scale of trading provides poor impact and transparency. In Asia, there is no strong competitive crude oil except the Middle East crude oil. There is only a weak price linking between crude oil and products. These are the background that the price of Middle East crude oil stays at the high level and the price adjusting functions are hard to work. The marker crude oil should be changed to another except Dubayy crude oil, and information should be dispatched from purchasers based on the stable standard crude oil. The real paper market should be created, and the force of speaking to oil producing countries should be enhanced by concentrating forces of major oil consuming countries in Asia. It is necessary to find out competitive crude oils. 5 figs., 6 tabs.

  20. Kei hea te Ora? The whereabouts of the health of children in the early childhood curriculum of Aotearoa New Zealand

    Directory of Open Access Journals (Sweden)

    Gibbons Andrew

    2015-12-01

    Full Text Available The policies and practices of early childhood teaching in Aotearoa New Zealand have been an ongoing site of political, economic, social and cultural contestation. Competing values and beliefs regarding experiences of both the child and the teacher have been central to the contesting. Helen May (2001, 2009 tracks these tensions through the waxing and waning of particular landscapes or paradigms, each of which can be seen to have contributed to the growth of the early childhood sector, its purpose, operations, manifestations, and its arguably tenuous cohesion as an educational sector. This paper provides a brief overview of the various paradigms, their purposes, and their spheres of influence (recognising that other papers in this special issue will contribute to a very detailed picture of early childhood education in Aotearoa before analysing the discourses of child health in relation to the early childhood curriculum. Health is woven into the strands and principles of Te Whāriki (Ministry of Education [MoE], 1996. Yet, this paper questions whether teachers and student teachers are attuned to what it means to have health as a key part of the curriculum, and explores whether health is a marginal consideration in the curriculum. The paper engages Foucault’s work, exploring tensions between pedagogical and medical disciplines in relation to the professionalisation of early childhood teaching. The idea of holism is then discussed as an approach to early childhood education curriculum discussions with reference to the participatory approaches to the development of Te Whāriki.

  1. FY 1990 Study Meeting of Catalyst (Iron system). Data; 1990 nendo shokubai kento kai (Tetsu kei) shiryo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The FY 1990 Study Meeting of Iron-system Catalyst was held at NEDO on March 12, 1991, and the data were arranged. In the study meeting, papers titled as follows were made public: About the behavior of H{sub 2}S on iron-system catalyst by Muroran Institute of Technology; Results of the test on iron-system catalyst in the BCL project by Research Institute, Mitsubishi Kasei Corp.; Results of the test on iron-system catalyst by 2.4 t/d PDU by NKK; Results of the test on iron-system catalyst by 0.1 t/d BSU by Mitsui Engineering and Shipbuilding Co.; Results of the test on iron-system catalyst by 1 t/d PSU by Nippon Steel Corp.; Results of the research at Government Industrial Development Laboratory, Hokkaido, and the study; Results of the research at National Chemical Laboratory for Industry and the study; Results of the research at the University of Tokyo and the study; Details of the development of synthetic iron sulfide and the attainment up to now by Asahi Chemical Industry Co. Moreover, the plenary session was held on research items for the development of iron-system catalyst in future. (NEDO)

  2. Leading research on supermetals. Part 2. Bulky material (Al system); Supermetal no sendo kenkyu. 2. Ogata sozai (aluminium kei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In order to find the higher critical strength, toughness and corrosion resistance of Al system materials than those obtained by conventional methods, crystal grain control was studied in a finer-grain region. The above characteristics of Al materials obtained by conventional technologies such as alloy element addition and heat treatment controlling crystal grains of several tens {mu}m are approaching critical values, resulting in poor characteristics for the latest needs. It has been confirmed experimentally in fundamental studies using small specimens that fine crystal grains of several {mu}m can remarkably enhance the above characteristics. Technology for creating mesoscopic structure-controlled materials was thus studied. In particular, creation of ultra-fine advanced Al alloy bulk materials by cryogenic processing method was selectively studied. The developmental approach and its issue were thus revealed for creating mesoscopic crystal structure by recovery and recrystallization of a highly distorted state obtained by cryogenic processing. 102 refs., 80 figs., 8 tabs.

  3. Kei hea te Ora? The Whereabouts of the Health of Children in the Early Childhood Curriculum of Aotearoa New Zealand

    Science.gov (United States)

    Gibbons, Andrew

    2015-01-01

    The policies and practices of early childhood teaching in Aotearoa New Zealand have been an ongoing site of political, economic, social and cultural contestation. Competing values and beliefs regarding experiences of both the child and the teacher have been central to the contesting. Helen May (2001, 2009) tracks these tensions through the waxing…

  4. Leading research on super metal. 2. Aluminium materials; Super metal no sendo kenkyu. 2. Ogata sozai (aluminium kei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Aluminum materials were surveyed to improve aluminum materials drastically so as to play an important role as prospective materials in response to the changing social environment. Aluminum materials have become the following metal materials to iron materials due to their light weight, durability, and profitability. Based on their merits and demerits, it was made clear how the aluminum materials contribute to the future resource saving, energy saving, and global environmental protection. Review was made on the two research and development themes which contribute to the creation of super metals. Hence, the themes proposed are focused on the creation of new aluminum mill products with ultra fine grain structure using very low temperature processing and on the creation of super-formability aluminum alloy sheets by advanced texture control using processing which can enhance the shearing stress. Results of the research and development are expected to provide wide applicability for other metals, ceramics, and polymers. 433 refs., 315 figs., 56 tabs.

  5. Robust control system for belt continuously variable transmission; Robust seigyo wo tekiyoshita mudan hensokuki no hensokuhi servo kei no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Adachi, K; Wakahara, T; Shimanaka, S; Yamamoto, M; Oshidari, T [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The continuously variable transmission control system consists of generation of a desired gear ratio and a servo gear ratio system. The servo gear ratio system must provide the desired response at all times without being influenced by external disturbances. These include oil pressure as well as variation in performance due to operating conditions or changes occurring with us. We have developed the servo gear ratio system incorporating a robust model matching method, which enables the belt continuously variable transmission to satisfy this performance requirement. 2 refs., 9 figs.

  6. Zero-ODP Refrigerants for Low Tonnage Centrifugal Chiller Systems

    National Research Council Canada - National Science Library

    Gui, Fulin

    1996-01-01

    ..., HFC-236cb, HFC-236fa, HFC-245cb, and HFC-254cb, for centrifugal chiller applications. We took into account the thermodynamic properties of the refrigerant and aerodynamic properties of the impeller compression process to this evaluation...

  7. Atmospheric chemistry of HFC-134a. Kinetic and mechanistic study of the CF3CFHO2 + NO2 reaction

    DEFF Research Database (Denmark)

    Møgelberg, T.E.; Nielsen, O.J.; Sehested, J.

    1994-01-01

    A pulse radiolysis system was used to study the kinetics of the reaction of CF3CFHO2 with NO2. By monitoring the rate of the decay of NO2 using its absorption at 400 nm the reaction rate constant was determined to be k = (5.0 +/- 0.5) x 10(-12) cm3 molecule-1 s-1. A long path length Fourier......-transform infrared technique was used to investigate the thermal decomposition of the product CF3CFHO2NO2. At 296 K in the presence of 700 Torr of air, decomposition of CF3CFHO2NO2 was rapid (greater than 90% decomposition within 3 min). The results are discussed in the context of atmospheric chemistry of CF3CFH2...

  8. Role of excited CF3CFHO radicals in the atmospheric chemistry of HFC-134a

    DEFF Research Database (Denmark)

    Wallington, T.J.; Hurley, M.D.; Fracheboud, J.M.

    1996-01-01

    with Oz, CF3CFHO + O-2 --> CF3C(O)F + HO2, and decomposition via C-C bond scission, CF3CFHO + M --> CS3 + HC(O)F + M. CF3CFHO radicals were produced by two different reactions: either via the self-reaction of CF3CFHO2 radicals or via the CF3CFHO2 + NO reaction. It was found that decomposition was much...

  9. Photovoltaic AC fusion converter (PVAC). Design consideration and experimental evaluation; Taiyoko hatsuden denryoku/shoyo denryoku kongo sochi no hoshiki to seino

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, Y. [Hachinohe National College of Technology, Aomori (Japan); Sakakibara, T. [Toyohashi University, of Technology, Aichi (Japan)

    1997-11-25

    The photovoltaic AC fusion converter (PVAC), of which cost reduction of the total system is possible, was developed. PVAC controls the supply of commercial power by preferentially supplying photovoltaic power to loads for realization of energy conservation. Further, setting the maximum output of solar cell less than the rated load, the system was made the one with no need of storage batteries. This system was realized in a hybrid of the conventional rectification technology and the stand-alone maximum power point tracking photovoltaic system technology. The solar cell input efficiency had been measured as 84% at maximum. Main losses are consumption power of power source, switching loss of inverter, and continuity loss of diode. Ninety-seven percent of the commercial power input efficiency was obtained. Main losses are consumption power of power source, continuity loss of diode bridge, and resistance loss of smoothing reactor. The effect of energy conservation by the use of PVAC was also admitted. 6 refs., 7 figs.

  10. Explosive treatment of Illinois No.6 coal with a mixed solvent of water and cyclohexanol; Mizu-cyclohexanol kongo yozai ni yoru Illinois tan no bakusai shori

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, T.; Takada, H.; Asami, K.; Yano, M. [Osaka City University, Osaka (Japan). Faculty of Engineering

    1996-10-28

    Coal was treated at high temperature under high pressure in the binary system mixed solvent of water and organic solvent, and the solvent treated coal was liquefied. When the treated coal was treated again by the explosive method in which high temperature and pressure were released immediately, the oil yield was higher than that by the normal method in which high temperature and pressure were reduced gradually to room temperature and atmospheric pressure. In this study, an explosive treatment unit with increased scale of sample amount was newly fabricated. Illinois No.6 coal was treated by the explosive method in a mixed solvent of water and cyclohexanol using this unit. Changes in shape on the surface, specific surface area, and functional groups were analyzed. The explosively treated coal contained more amount of low boiling point components than the normally treated coal. It was suggested that the oil yield of explosively treated coal increased due to the liquefaction of these components during the successive hydrogenation process. For the explosively treated coal, micro pores were fractured by the rapid change in the volume of solvent molecules, and the specific surface area was smaller than that of the normally treated coal. When the treatment temperature was increased from 300{degree}C to 350{degree}C, specific surface areas of both the treated coals increased. 2 refs., 3 figs., 2 tabs.

  11. Survey and research on how large-scale technological development should be in the future; Kongo no ogata gijutsu kaihatsu no hoko ni tsuite no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Tasks to be subjected to research and development under the large-scale industrial technology research and development system are discussed. Mentioned in the fields of resources and foods are a submarine metal sulfide mining system, a submarine oil development system for ice-covered sea areas, an all-weather type useful vegetable automatic production system, etc. Mentioned in the fields of social development, security, and disaster prevention are a construction work robot, shelter system technologies, disaster control technologies in case of mega-scale disasters, etc. Mentioned in the fields of health, welfare, and education are biomimetics, biosystems, cancer diagnosis and treatment systems, etc. Mentioned in the field of commodity distribution, service, and software are a computer security system, an unmanned collection and distribution system, etc. Mentioned in the field of process conversion are aluminum refining, synzyme technologies for precise synthesis, etc. Mentioned in the field of data processing are optical computers, bioelectronics, etc. Various tasks are pointed out also in the fields of aviation, space, ocean, and machining. (NEDO)

  12. Current state and future prospect on polyacrylic scid based superabsorbent polymer. Polyacrylic sankei kokyusuisei polymer no genjo to kongo no tenkai

    Energy Technology Data Exchange (ETDEWEB)

    Shimomura, T.; Kobayashi, H. (Nippon Shokubai Kagaku Kogyo Co. Ltd., Osaka (Japan))

    1991-10-01

    A polymer that absorbs water vigorously and swells is called a superabsorbent polymer (SAP). This peculiar character has developed diverse applications including paper diapers, and its production showed a rapid growth to more than 200,000 tons (worldwide) in the past decade. This paper introduces the development and applications for polyacrylic acid-based SAP, a representative SAP. The research began in the U.S.A. in about the year 1976. For its characteristics suitable for paper diapers and cost advantages, the acrylate-based SAP has become accounting for the most at the present. The polymer is manufactured by polymerzation crosslinking of acrylic acid or sodium acrylate to produce polyacrylate crosslinked bodies. The polymer swells to 100 to 1000 times in deionized water, and turns into a hydrogel. Unlike a sponge, the swelled gel will not ooze out water even if pressed. However, its absorption performance decreases extremely in electrolytic aqueous solution, which is a problem for the future development. 17 refs., 5 figs., 7 tabs.

  13. Perspective of next generation training system from the viewpoints of human interfaces. Human interface kara mita kyoiku kunren system no genjo to kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, S [Mitsubishi Electric Corp., Tokyo (Japan)

    1992-12-10

    This paper describes an education and training system placing its emphasis on human interfaces. The paper indicates that the currently used education and training systems lack training functions to cultivate knowledge-based judgment abilities that can find adequate solutions to events that have not been experienced previously; such judgments require deep understanding on the objects; and this training requires a system to aid the comprehension based on knowledges in the realm of recognition science for the 'human understanding'. Next, a pedagogical interface is proposed for aiding the comprehension. The paper enumerates functions indispensable for the comprehension including setting the 'loop for representation and examination', aiding the representation to examination loop, aiding roles by others, and realizing interactions through a hypothetical world. Also enumerated as fundamental techniques to structure such interface are information structuring techniques, groupware techniques, and virtual reality techniques. 19 refs., 10 figs.

  14. Flow and mixing characteristics in a stirred tank with dual wide paddles; 2 dan waido padoruyoku tsuki kakuhan sonai no ryudo{center{underscore}dot}kongo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Takata, Kazutaka; Ito, Hisayoshi; Kikuchi, Masahiko; Okamoto, Yukimichi [Shinko Pantec Corp., Hyogo (Japan)

    1999-03-10

    Flow structure and mixing characteristics in a stirred tank with dual wide paddle impeller were examined using computational fluid dynamics (CFD). CFD was conducted using analysis code for fluid flow, and velocity measured by laser doppler velocimeter, power consumption and mixing time were used for evaluating computed results. The computed flow field and power consumption agreed well with themeasured values within 5 % mixing process well agreed with the observations. Since the computed flow pattern and mixing process agreed well with the measured values, computed results are useful for evaluating complex flow field in a stirred tank. A detailed investigation using computed results are useful for evaluating complex flow field in a stirred tank A detaile investigation using computed results shows that dual cross-installed wide paddle impellers lead to superior mixing performance in the stirred tank, and pressure gradient between upper and lower paddles is found to be the factor that promotes fluid transport in the tank, which is never the case when the dual wide paddles are installed in the same plane. (author)

  15. Mixing of two-component flow in a simplified stirred tank with cellular automaton method; Cellular automaton ho ni yoru kakuhan sonai no niseibunryu no kongo keisan

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, S; Takahashi, R [Tokyo Institute of Technology, Tokyo (Japan)

    1996-01-25

    The applicability of a cellular automaton technique to engineering problems will be examined by dealing with mixing in multicomponent flow. The quality and accumulation rate of the product depend on the mixing of raw materials basically. After thoroughly understanding the mixing process, we optimize the geometrical allocation of such elements as a propeller with casing, a chimney and a product output nozzle in a reactor. Usually mixing is formulated by partial differential equations of conservation laws and empirical formulae, and solved numerically by the finite difference technique. In order to evaluate the fine structure of time-dependent interfacial behavior in multicomponent flow, the cellular automaton technique is used, since this has an advantage of describing the pattern formation in detail. It will be demonstrated in the present paper that mixing of two-component immiscible flow is reasonably simulated mesoscopically. 13 refs., 17 figs.

  16. Joint study on smelting reduction. ; Results of elementary study and future studies. Yoyu kangen kyodo kenkyu; Yoso kenkyu no seika to kongo no torikume

    Energy Technology Data Exchange (ETDEWEB)

    1991-03-01

    The paper outlines results of elementary study on the coal direct-use iron-making process and how to tackle with it in future. In the process coal and iron ores are used directly without prior treatments like coking and briquetting. The process is composed of three elements: smelting reducing furnace, preliminary reduction fluidized bed, gas reforming furnace. Making mathematical models as a means of study of the process, material balance and heat balance are calculated. Operational unit requirements are estimated, changing them in the range of 20-60% of the post combustion based on three fundamental processes each of which is composed of one or a combination of the three elements. The total cost is also trially calculated, estimating fixed cost including installation cost, etc. With no big differences in the iron-melting cost excluding by-products in each process, the cost may be reduced by 5-10% of that in the blast furnace process. The elementary study has continued almost satisfactorily and attained the expected target, though there still remain some problems. In 1990 the study started of a pilot plant with a 500t/day capacity. 12 figs.

  17. Effects of fuel and air mixing on WOT output in direct injection gasoline engine; Chokufun gasoline kikan ni okeru nenryo to kuki no kongo to shutsuryoku seino

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T; Iriya, Y; Naito, K; Mitsumoto, H; Iiyama, A [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-10-01

    The effects of in-cylinder charge motion and the characteristics of the fuel spray and piston crown shape on WOT output in a direct injection gasoline engine are investigated. The fuel and air mixing process in a cylinder is analyzed by computer simulation and LIF method visualization. As a result, the technical factors to achieve enough mixing in a DI gasoline engine equipped with bowl in piston optimized for stratified combustion are clarified. 7 refs., 9 figs., 1 tab.

  18. Effects of MTBE blended diesel fuel on diesel combustion and emissions; MTBE kongo keiyu ga diesel nensho haiki ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Shundo, S; Yokota, H; Kakegawa, T [Hino Motors, Ltd., Tokyo (Japan)

    1997-10-01

    The effects of MTBE (Methyl-t-butyl ether) blended diesel fuel on diesel combustion and emissions were studied. In conventional diesel combustion, the testing mode was carried out in conformity with the Japanese 13 mode. Furthermore, this fuel was applied to a new combustion system (Homogeneous Charge Intelligent Multiple Injection). MTBE blended diesel fuel is more effective in the case of new combustion system and very low NOx, PM capability is suggested. 6 refs., 6 figs., 2 tabs.

  19. Destratification efficiency by hypolimnitic water lifter with air bullets. Kihodan wo mochiita shinsosui yosui shisetsu ni yoru mitsudo seiso no kongo koritsu

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, H; Suga, K [Utsunomiya University, Tochigi (Japan). Faculty of Engineering; Asaeda, T [Saitama University, Saitama (Japan). Faculty of Engineering

    1994-02-21

    The intermittent aeration and circulation method is used frequently to destruct temperature stratification in a reservoir to prevent it from eutrophication. This method uses a cylinder erected in water, into which air bullets are shot out intermittently to circulate and mix heavier water mass upward. The present study has performed numerical analysis on the process to mix density stratifications by operating an intermittent water lifter cylinder for an extended period of time, and discussed responses of each factor to variation. The numerical computation has been carried out according to the equation of motion for water and air in the water lifter cylinder, and the numerical model that hypothesizes the double plume after air bubbles have departed from the water lifter cylinder. The result indicated that the amount of hypolimnitic water lifted against the amount of air injected can be expressed by an empirical formula that uses only the relative air bullet volumes. An evaluation formula for the water lifting efficiency has also been derived. It has been found for the stratification mixing that trends in the mixing efficiency can be identified by two parameters of dimensionless air bubble amount and stratification strength. 17 refs., 11 figs., 4 tabs.

  20. Effect of oxygenated fuel on premixed lean diesel combustion; Kihaku yokongo diesel nensho ni oyobosu gansanso nenryo kongo keiyu no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S.; Miyamoto, T.; Harada, A.; Akagawa, H.; Tsujimura, K. [New ACE Institute Co. Ltd., Tokyo (Japan)

    1998-05-01

    Because injection timing in diesel engines is early in a premixed lean diesel combustion system using early fuel injection, ignition timing is determined by ignitability of the fuel used. The conventional diesel fuel, which has good ignitability, causes excessively early ignition, thus aggravating fuel consumption. In order to reduce cylinder temperature with an aim of delaying ignition timing to improve the fuel consumption, attempts are being made on using low cetane fuels to reduce CO2 gas supply or compression ratio, and to vary ignitability of the fuels. The present study investigated ignition timing control and properties of exhausts by mixing different types of oxygenated fuels into light oil. Mixing the oxygenated fuels into light oil proved that the ignition timing can be controlled, and mixing such low cetane fuels as ethanol and MTBE achieved improvement in fuel consumption. Trial use of the oxygenated fuels aggravated CO concentration, which is caused because the cylinder temperature was reduced. Numerical calculations suggest that use of fuels with faster evaporation speed and lower cetane number is effective in improving the fuel consumption and the exhausts. 12 refs., 9 figs., 2 tabs.

  1. Actual situation and future tendency of relaxation of petroleum restrictions in Western Europe. Seio ni okeru sekiyu kisei kanwa no jittai to kongo no doko

    Energy Technology Data Exchange (ETDEWEB)

    1989-07-31

    An oversea investigation was made in 1988 to study the present situation of the relaxation trends of petroleum resrictions in the countries of Western Europe. Among petroleum markets of West European countries, in those of West Germany and UK both quantity and price have had no restrictions. And in France they were liberalized quite recently. On the other hand, in South European countries such as Italy, Spain and Greece the prices of petroleum products are controlled by the governments. EC is going to integrate petroleum markets by the end of 1992 so that petroleum products may flow beyond the borders freely. In France, relaxation of restrictions on the petroleum industry was carried out in 1985 employing the petroleum business law of 1928 with elasticity and four years have passed since then. In Italy petroleum companies cannot decide the prices of major petroleum products freely. In Spain, the petroleum market is going to be completely liberalized in 1993 in accordance with the engagement with EC. Greece is at strife with EC on the adjustment of policies. 26 figs., 86 tabs.

  2. Current status of natural gas in Asia and future problems; Asia no tennen gas josei no genjo to kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K. [The Institute of Energy Economics, Tokyo (Japan)

    1997-01-30

    This paper describes current status of natural gas in individual countries of Asia and future prospects. Japan is the largest consuming country, and consumes 29% of Asia-Pacific region. Japan, Korea and Taiwan consume 35%. All of natural gas are imported. Indonesia, the largest LNG exporting country in the world, makes efforts to develop natural gas in response to the future shortage of oil with the economic growth. In Malaysia, natural gas utilization is extending for the diversification of energy. Natural gas utilization occupies 36% of primary energy consumption, which results in the reduced oil consumption. Brunei is an important natural gas supplier in Asia, and 90% of the production is exported. Australia has a large reserve of natural gas, which is exported besides domestic use. China has a large latent demand as well as India. In Taiwan, most of natural gas is imported. In Korea, demand of city gas has extended in addition to power generation, and it will extend in future. Current conditions in Vietnam and Thailand are also described. In the Philippine, natural gas is not used. 3 figs., 8 tabs.

  3. Present conditions and future tasks of Japan`s ship machinery industry; Nihon hakuyo kogyo no genjo to kongo no kadai ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Akahoshi, S. [Ministry of Transportation, Tokyo (Japan)

    1994-09-01

    Although Japan`s shipbuilding industry has been maintaining a seat for the first place in the world over 30 years or more in a contract award quantity for the new shipbuilding work, Korea got ahead of Japan and has come to be a top at the first time in 1993. Even though the various factors could be thought, it has become a turning point to be reconsidered how Japan`s shipbuilding industry should be from now on for the naval architects and persons concerned in Japan. While Japan`s production of the maritime industrial products has been in general showing the recovering tendency by a demand restoration of the large scale vessels and so forth since 1987 afterward, on the other hand, affected by an influence of the recession of the world economic activities, the total production amount in 1993 has turned to a little bit decrease and its amount was 831.8 billion yen (a ratio to the previous year: 96.4%). Though a business environment surrounding the maritime industry, in order to successively continue the work shop site inside this country as an important industry through this industry from now on, it is thought that a restoration of the price competition should be made an effort on one hand by a standardization of the maritime equipments and tools making an exclusion of the wastefulness as an object, and a strengthening of the international competitiveness at the non-price aspects such as a functionality of the products, a reliability and so forth is indispensable on the other hand. 6 figs., 3 tabs.

  4. Preparation of. beta. -spodumene glass-ceramics from blast furnace slag. Koro slag wo genryo to shita. beta. -spodumene kei kesshoka glass no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Wang, M. (National Kaoshing Institute Technology, Kaoshiung (Rep. of China)); Hon, M. (National Cheng Kung University, Tainan (Rep. of China))

    1990-07-01

    Li {sub 2} O-CaO-Al {sub 2} O {sub 3} -SiO {sub 2} (LCAS) glass-ceramics were prepared from blast furnace slag by quenching in water after heating at 1,450 {degree} C for 3 hours. Blast furnace slag (40.0wt%) containing CaO, MgO, Al {sub 2} O {sub 3} and SiO {sub 2} as major components was used as a raw material, and batch compositions were modified by mixing blast furnace slag with Al {sub 2} O {sub 3}, SiO {sub 2} and Li {sub 2} CO {sub 3}, and a nucleating agent TiO {sub 2}. The A specimen with TiO {sub 2} of 7.4wt% and B specimen with 4.6wt% were prepared, and the crystallization process of the glass was examined with X-ray diffraction, electron diffraction and so forth. As a result, a major crystalline phase was {beta} -spodumene (Li {sub 2} O-Al {sub 2} O {sub 3} -4SiO {sub 2}), and the average thermal expansion coefficients of A and B were 40.1 and 47.2 {times} 10 {sup {minus} 7} / {degree} C in the temperature range from 25 to 700 {degree} C, respectively. A small amount of titanite was also observed in A as a sub-phase. 14 refs., 5 figs., 3 tabs.

  5. Study of a flapper-nozzle system for a water hydraulic servovalve; Suiatsu survo ben ni mochiiru nozzle flapper kei no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Urata, E.; Nakao, Y. [Kanagawa University, Kanagawa (Japan). Faculty of Engineering

    1997-06-25

    The paper discusses the characteristics of a flapper-nozzle system for water hydraulic servovalves. High pressure water at the supply port is first used as the working fluid for the hydrostatic bearings supporting the spool. Spool valve stiction induced by poor lubrication with water is thus avoided. The fluid is then led to the ends of the spool and is used as the working fllid of the flapper-nozzle system. In the new flapper-nozzle system the circumferential clearance of the spool becomes a laminar restriction that substitutes fixed orifice used in conventional servovalves. The linearity in the pressure-displacement relationship of the new flapper-nozzle system is better than that of conventional fixed orifice systems. 7 refs., 11 figs., 2 tabs.

  6. Noise abatement technique for large vehicles of bus and truck families; Basu / torakku kei ogata sharyo no tei soon ka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Takatsuki, K. [Isuzu Motors Ltd., Tokyo (Japan)

    1997-09-25

    It is remarked that noises in the cab of large buses and large trucks have been reduced about 10dB(A) during last 15 years, and experimental analytical methods for the noise abatement in the cab of these vehicles are introduced together with cases where measures are incorporated. Firstly, contribution to noise by each noise source is explained and a test method of noise exposure by the partial division of a large truck cab is presented, and on the base of the result obtained, it is found that the measures against the engin noise taken in cooperation with car manufacturer reside on the selection of noise absorbing/isolating materials and the actual examples are shown for a truck floor and the upper noise-proof structure of a bus. There are peaks at 100, 250 and 400 Hz on the noise spectra of an admission port, and they correspond to the problematic frequencies. Their analytical methods are presented comprising a speaker test, a simulation analysis and a boundary element method together with models and calculation examples. As for measures against the noise and vibration in the admission system, installation of resonator and vibration isolation by rubber are mentioned. Lastly, a synopsis on noise phenomena of the driving system is established and a twist resonance phenomenon that frequently occurs in the driving system is particularly described including their examples of analysis and countermeasures. 3 refs., 22 figs., 1 tab.

  7. Surface modification method of rare earth-nickel hydrogen storage alloy for a battery; Denchiyo kidorui-nikkeru kei suiso kyuzo gokin no hyomen kaishitsu shoriho

    Energy Technology Data Exchange (ETDEWEB)

    Higashiyama, N.; Kimoto, M.; Matsuura, Y.; Kuroda, Y.; Nogami, M.; Nishio, K.; Saito, T.

    1996-07-16

    The characteristics of an alkaline battery with hydrogen storage alloy depend significantly on the activity of the used rare earth-nickel hydrogen storage alloy and require an activation process in its manufacturing. However, the previous manufacturing method was found to have a defect that surface modification cannot be uniformly conducted due to a rapid increase of pH of the processing solution during the processing. This invention aims to present a surface modification method to enable to produce uniform surface of the alloy particles with a high activity. In this invention, the rare earth-nickel hydrogen storage alloy is immersed in a buffer solution of pH 1 to 3.6 for a fixed period followed by washing with water or an alkaline solution. The rapid change of pH can be avoided by the use of the buffer solution and the surface of the alloy particles is modified uniformly. The use of the obtained alloy suppresses the increase of the internal pressure in the battery during charging and affords an alkaline battery with a long cycle life and a high performance. 1 fig., 3 tabs.

  8. Evaluation of corrosivity of the vapor-phase environments to sterilized water with chlorine; Enso kei mekkin shorisui no kisho kankyo no fushokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakata, Michio. [Nippon Steel Corp. Yamaguchi (Japan). Technical Development Bureau

    1999-08-15

    Corrosivity of vapor-phase aenvironments in indoor pool, water thank, and water purification plants was investigated. Sodium hypochlorite (NaClO) was used as a sterilizing agent in indoor pool, while chlorine gas was used in water tank and water purification plants. It was found that Cl{sup -} ion were concentrated in the dew formed in the indoor pool. H{sup +} ions as well as Cl{sup -} ions were accumulated in the dew dormed in the water tank ans water purification plants. Thus, the corrosion condition was varied with the type of sterilizing agents used. Through the investigation of water tanl, the relationship between pH and Cl{sup -} ion concentration was given as follow; pH=-1.09-2.19 log [Cl{sup -}] (mol/L). Corrosivity of vapor-phase enviroments in sterilizing water systems would be characterized by the exstence of oxidizing chemical agents such as ClO{sup -} and HClO, the shift of corrosion potenrial of the thin water film, and the accumulation of H{sup +} and/or Cl{sup -} ions in the dew. (author)

  9. Recent development in crystal growth of large-diameter Y-QMG (reg sign) bulk superconductors; Y kei ogata QMG (reg sign) baruku koonchodendotai no kaihatsu jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, T.; Morita, M. [Nippon Steel Corporation, Tokyo (Japan); Masahashi, N. [Tohoku University, Miyagi (Japan). Institute for Materials Research

    1999-11-25

    The current status of large-diameter Y-Ba-Cu-O OMG(reg sign) bulk superconductors is described. 75 mm-diameter QMG(reg sign) samples with fairly concentric trapped-magnetic-flux-density distributions have been successfully grown. In addition, a record-high value of the magnetic levitation force, 171 kgf, measured at 77 K using a 90 mm-diameter Nd-Fe-B magnet has been obtained for a 100 mm-diameter sample. The crystal orientation of subgrains in the sample was determined using Electron Back-Scattering Diffraction as well as using a conventional optical apparatus including a He-Ne-laser. For the sample grown under normal process conditions, the maximum value of the [001]-axis misorientation angles at the subgrain-boundaries we obtained in the c-substructure region is 2.9 degree. However, in the a/b-substructure regions, the misorientation angles are larger, and the maximum value obtained is 6.6 degree, exceeding the critical angle at which a significant reduction of the critical current density occurs in Y123 thin films due to the weak-link problem. (author)

  10. Optimizing C4+ and C5+ beams of the Kei2 electron cyclotron resonance ion source using a special gas-mixing technique

    International Nuclear Information System (INIS)

    Drentje, A.G.; Muramatsu, M.; Kitagawa, A.

    2006-01-01

    With the prototype electron cyclotron resonance ion source for the next carbon therapy facility in Japan a series of measurements has been performed in order (a) to find the best condition for producing high beam currents of C 4+ ions, and (b) to study the effect of 'special' gas mixing by using a chemical compound as a feed gas. The effect would then appear as an increase in high charge state production in this case of C 5+ ions. In 'regular' gas-mixing experiments it is well known that an isotopic phenomenon occurs: a heavier isotope of the mixing gas is increasing the production of high charge states of the beam gas ions. A similar isotopic effect has been found in the present experiment: with deuterated methane (CD 4 gas) the C 5+ beam currents are about 10% higher than with regular methane (CH 4 gas). The 'mixing-gas' ratio D (or H) to C can be decreased by choosing, e.g., butane gas; in this case the isotopic effect for C 5+ production is even stronger (>15%). For production of C 4+ ions the isotopic effect appears to be absent. Clearly this is related to the much easier production. It turns out that the relative amount of carbon is much more important: butane gives about 10% higher C 4+ -ion currents than methane

  11. Investigation of migration of organic silicone into stone and its prevention; Silicone kei dansei secchakuzai no seibun ga sekizaichu ni shinto suru gensho no kyumei to shinto taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, M.; Sasaki, M. [Kajima Construction Co. Ltd., Tokyo (Japan)

    1998-07-30

    Quantitative analyses of silicone migration into marble from elastic silicon adhesive were carried out by EPMA and LMA, and the amount of migrated silicone was calculated in terms of silicone concentration. By EPMA, silicone distribution into the area centering around the boundary between elastic adhesive and marble was clarified, and the migrating condition of silicone from elastic adhesive to marble was made clear. In the case of LMA, silicone concentration in micro-area in marble was measured to use the measured result for the succeeding analyses. As a result of the analysis, the trend of the change of silicone migration with the passage of time could be expressed by treating the silicone migration as diffusion phenomenon, and the depth of silicone migration could be quantified. It was confirmed that the cover primer applied at the back of marble to inhibit migration could prevent contamination of marble caused by silicone migration. The analytical method of this study seemed to be applicable to other stone materials or other adhesive and sealing materials. 14 refs., 12 figs., 2 tabs.

  12. Research and development of turbo engines in HYPR project. Choonsoku yusokiyo suishin system no kenkyu kaihatsu ni okeru turbo kei engine no shisaku

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y; Itahara, H; Kohara, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The present paper outlined the project which aimed at developing a combined cycle engine by a combination of turbojet engine operable from the takeoff or landing to Mach 3 and ramjet engine operable from Mach 2.5 to 5. The outline included the test result report of a prototypical engine which was the main subject of project. Upon conceptual research on the engine to comply with the future supersonic passenger plane, a variable cycle engine jointly equipped with a mixer/ejector noise lowering device was applied as a turbojet engine to lower the noise. The prototypical turbojet engine which was a target engine subscaled to about 1/10 in thrust aimed at demonstrating the total system performance of the turbojet engine which structured a combined cycle engine. Prior to testing the above prototype, the core engine was singly tested (in Phase 1) with a confirmed good result in firing and startup characteristics. 4 refs., 9 figs., 3 tabs.

  13. Maori Potential: Barriers to Creating Culturally-Responsive Learning Environments in Aotearoa/new Zealand: Te Timatanga O Te Ara--Kei Whea Te Ara?

    Science.gov (United States)

    Henderson, Lesleigh

    2013-01-01

    New Zealand Education reforms aligned with raising Maori student success are yet to result in Maori students reaching their educational potential (Howard, 2010; ERO, 2008; 2010). Why do many New Zealand teachers struggle to create and deliver programmes which allow Maori learners to succeed as Maori? What barriers and enablers exist today in New…

  14. Electrical properties of V205-ZnO-TeO2 glasses. V205-ZnO-TeO2 kei garasu no denki dendo

    Energy Technology Data Exchange (ETDEWEB)

    Mori, H; Igarashi, J; Sakata, H [Tokai Univ., Tokyo (Japan). Faculty of Engineering

    1993-12-01

    It is known that glasses contained Transition Metal Oxide (TMO) such as V2O5 show a semi-conductivity, those conductive mechanism has been understood according to the Small Polaron Hopping (SPH) theory developed by Mott and Austin. Authors investigated the glass formation regions, de-conductivity([sigma]) and the conductive mechanism for V2O5-Bi2O3-TeO2 glasses as a tellurite glass containing the TMO. It was clarified that the adiabatic SPH and the non-adiabatic SPH are satisfied for the glasses with V2O5>50 mol% and V2O5<50 mol%, respectively. In this study, the electrical properties of V2O5-ZnO-TeO2 glasses were investigated, and the SPH conductions were considered from the standpoints of the polaron band width J, carrier mobility [mu], carrier density Nc. The conductive mechanism and dependence of V2O5 density on Seebeck coefficients Q were clarified in which a formation region of V2O5 is from 30 to 60 mol%. 40 refs., 9 figs., 2 tabs.

  15. Effect of laser heat treatment on intergranular corrosion of austenitic stainless steel; Austenite kei stainless ko no ryukai fushoku kanjusei ni oyobosu laser netsushori no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Osawa, M.; Yoneyama, T. [Tokyo Denki University, Tokyo (Japan). Faculty of Engineering; Isshiki, Y. [Tokyo Metropolitan Industrial Technology Center, Tokyo (Japan)

    1995-03-15

    The laser heat treatment of SUS304 steel was studied to lower the intergranular corrosion sensitivity of austenitic stainless steel. By the short-time heating around 923K, the SUS304 steel is sensitized to the intergranular corrosion with the deposition of Cr carbide into the granular field of crystals. To recover it, it is necessary to solidly dissolve, and simultaneously, quickly cool the Cr carbide above 1273K. For such solution heat treatment, CO2 laser beams were used with the treatment condition that the power and beam diameter were 800 to 1200W and 0.3 to 0.64cm, respectively. Regardless of both power density and beam diameter, the desensitization was observed at heating temperatures above 1323K. As a result of calculation by simulation, the solid dissolution of Cr carbide and recovery of Cr`s depletion zone in the granular field of crystals took place in a very short time at heating temperatures above 1323K. It agreed well with the experimental result. The laser beams are effective in the solution heat treatment of stainless steel. 14 refs., 15 figs., 1 tab.

  16. Distribution of the near-inertial kinetic energy inside mesoscale eddies: Observations in the Gulf of Mexico

    Science.gov (United States)

    Ixetl Garcia Gomez, Beatriz; Pallas Sanz, Enric; Candela Perez, Julio

    2017-04-01

    The near-inertial oscillations (NIOs), generated by the wind stress on the surface mixed layer, are the inertia gravity waves with the lowest frequency and the highest kinetic energy. NIOs are important because they drive vertical mixing in the interior ocean during wave breaking events. Although the interaction between NIOs and mesoscale eddies has been reported by several authors, these studies are mostly analytical and numerical, and only few observational studies have attempted to show the differences in near-inertial kinetic energy (KEi) between anticyclonic and cyclonic eddies. In this work the spatial structure of the KEi inside the mesoscale eddies is computed using daily satellite altimetry and observations of horizontal velocity from 23 moorings equipped with acoustic Doppler current profilers in the western Gulf of Mexico. Consistent to theory, the obtained four-year KEi-composites show two times more KEi inside the anticyclonic eddies than inside the cyclonic ones. The vertical and horizontal cross-sections of the KEi-composites show that the KEi is mainly located near to the surface of the cyclonic eddies (positive vorticity), whereas the KEi in anticyclonic eddies (negative vorticity) is maximum in the eddy's center near to the base of the eddy where the NIOs become more inertial, are trapped, and amplified. The mean vertical profiles show that the cyclonic eddies present a maximum of KEi near to the surface at 50, while the maximum of KEi in the anticyclonic eddies occurs between 900 and 1100 m. Inside anticyclonic eddies another two relative maximums are observed, one in the mixed layer and the second at 300 m. In contrast, the mean profile of KEi outside the mesoscale eddies has the maximum value at the surface ( 50 m), with high values of KEi in the first 200 m and negligible energy beneath that depth. A different mean distribution of the KEi is observed depending on the type of wind generator: tropical storms or unidirectional wind.

  17. Stranõ Baltii obvinjajutsja v tranzite nezakonnoi drevessinõ

    Index Scriptorium Estoniae

    2005-01-01

    Maailma Looduse Fondi (WWF) hinnangul on Baltimaad ning Brasiilia, Kongo ja mõned teised Ida-Aafrika riigid põhiallikad, kust saabub Euroopa Liitu ebaseaduslik metsamaterjal. Balti riikide puhul on eelkõige tegemist Venemaalt saabuva transiidiga

  18. 1Department of

    African Journals Online (AJOL)

    USER

    2015-04-07

    Apr 7, 2015 ... under cultivation and improved cassava varieties coupled with other inputs to boost to productivity of farmers. ... Domestic Product (GDP) of the nation. (Bureau of African ..... Kongo Conference Hotel, Zaria,. Kaduna State ...

  19. Indiast saab maailma rahvarohkeim riik / Tõnu Prei

    Index Scriptorium Estoniae

    Prei, Tõnu, 1950-

    2005-01-01

    ÜRO rahvastikuraporti andmeil on maakera elanike arv 2050. a. 9,1 miljardit, kusjuures poole 2,6-miljardilisest juurdekasvust annavad vaid 9 riiki - India, Pakistan, Nigeeria, Kongo, Bangladesh, Uganda, USA, Etioopia ja Hiina

  20. 40 CFR Appendix C to Subpart B of... - SAE J2788 Standard for Recovery/Recycle and Recovery/Recycle/Recharging Equipment for HFC-134a...

    Science.gov (United States)

    2010-07-01

    ... Part 82 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Servicing of Motor Vehicle Air Conditioners Pt. 82, Subpt. B, App. C... reuse in, mobile air-conditioning systems and recovery/recycling and system recharging of recycled...

  1. Experimental Study of p-rho-T Relationship of Compressed Liquid Phase for Octafluoropropane and Two near Azeotropic Ternary HFC/HC Mixtures

    Czech Academy of Sciences Publication Activity Database

    Klomfar, Jaroslav; Součková, Monika; Pátek, Jaroslav

    2012-01-01

    Roč. 57, č. 5 (2012), s. 1627-1634 ISSN 0021-9568 R&D Projects: GA ČR GA101/09/0010 Institutional research plan: CEZ:AV0Z20760514 Keywords : octafluoropropane * R413a * R417a Subject RIV: BJ - Thermodynamics Impact factor: 2.004, year: 2012 http://pubs.acs.org/doi/abs/10.1021/je300148f

  2. Strain Hardening Cement Composites Structural Design and Performance State-of-the-Art Report of the RILEM Technical Committee 208-HFC, SC3

    CERN Document Server

    Kanda, Tetsushi

    2013-01-01

    Strain Hardening Cement Composites, SHCC hereafter, demonstrate excellent mechanical behavior showing tensile strain hardening and multiple fine cracks. This strain hardening behavior improves the durability of concrete structures employing SHCC and the multiple fine cracks enhance structural performance. Reliable tensile performance of SHCC enables us to design structures explicitly accounting for SHCC’s tensile properties. Reinforced SHCC elements (R/SHCC) indicate large energy absorbing performance under large seismic excitation. Against various types of loads, R/SHCC elements can be designed by superimposing re-bar performance and SHCC’s tensile performance.  This report focuses on flexural design, shear design, FE modeling and anti-seismic design of R/SHCC elements as well as application examples.  Establishing design methods for new materials usually leads to exploring application areas and this trend should be demonstrated by collecting actual application examples of SHCC in structures.

  3. The promotion of sustainable development in China through the optimization of a tax/subsidy plan among HFC and power generation CDM projects

    International Nuclear Information System (INIS)

    Resnier, Martin; Wang, Can; Du, Pengfei; Chen, Jining

    2007-01-01

    China is expected to reach record growth by 2020 in the energy sector by at least doubling its electricity generation capacity. In order to protect the environment and foster economic development, China will greatly benefit from transfers of state-of-the-art power generation technologies through international agreements such as the Clean Development Mechanism (CDM). However, a buyer-driven carbon market and a highly competitive environment due to more cost-effective projects attribute to China's need to achieve a balance between sustainability and profitability for CDM projects implemented in China. In the CDM Tax/Subsidy Optimization Model (CDMTSO Model) here developed, a sustainable development assessment method evaluates the CDM projects' economic and environmental benefits and an optimization program returns tax/subsidy rates at which the greatest number of CDM technologies becomes viable and where 'better' CDM projects can be the most profitable, bringing China's development on a more sustainable path. The results show that the CDMTSO Model brings the sustainable CDM projects' Internal Rate of Return closed to 10%. If a discount rate of 9% is considered, it allows three clean energy technologies (natural gas combined cycle, wind energy, and hydropower) to become economically viable and the environmental costs avoided are increased by 37%

  4. 40 CFR Appendix D to Subpart B of... - SAE J2810 Standard for Recovery Only Equipment for HFC-134a Refrigerant

    Science.gov (United States)

    2010-07-01

    ... removed from, motor vehicle air-conditioning systems. 1. Scope The purpose of this SAE Standard is to... 700 Standard or allow for recycling of the recovered refrigerant to SAE J2788 specifications by using... (R-134a) Recovery/Recycling Equipment and Recovery/Recycling/Recharging for Mobile Air-Conditioning...

  5. Observations of near-inertial kinetic energy inside mesoscale eddies.

    Science.gov (United States)

    Garcia Gomez, B. I.; Pallas Sanz, E.; Candela, J.

    2016-02-01

    The near-nertial oscillations (NIOs), generated by the wind stress on the surface mixed layer, are the inertia gravity waves with the lowest frequency and the highest kinetic energy. NIOs are important because they drive vertical mixing in the interior ocean during wave breaking events. Although the interaction between NIOs and mesoescale eddies has been reported by several authors, these studies are mostly analytical and numerical, and only few observational studies have attempted to show the differences in near-inertial kinetic energy (KEi) between anticyclonic and cyclonic eddies. In this work the spatial structure of the KEi inside the mesoscale eddies is computed using daily satellite altimetry and observations of horizontal velocity from 30 moorings equipped with acoustic Doppler current profilers in the western Gulf of Mexico. Consistent to theory, the obtained four-year KEi-composites show two times more KEi inside the anticyclonic eddies than inside the cyclonic ones. The vertical cross-sections of the KEi-composites show that the KEi is mainly located near the surface and at the edge of the cyclonic eddies (positive vorticity), whereas the KEi in anticyclonic eddies (negative vorticity) is maximum in the eddy's center and near to the base of the eddy where the NIOs become more inertial, are trapped, and amplified. A relative maximum in the upper anticyclonic eddy is also observed. The cyclonic eddies present a maximum of KEi near to the surface at 70 m, while the maximum of KEi in the anticyclonic eddies occurs between 800 and 1000 m. It is also shown the dependence between the distribution and magnitude of the KEi and the eddy's characteristics such as radius, vorticity, and amplitude.

  6. Fiscal 1992 survey report. Promotion of coal importing base buildup (How ocean freight system should be in the future); 1992 nendo kaigaitan yunyu kiban seibi sokushin chosa. Kongo no gaiko yuso taisei no arikata ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    When a general view is taken of coal chains that connect overseas coal suppliers to Japan's end users, it is found that no survey has ever been made to sufficiently explain marine transportation of coal. It is now expected that the gap between supply of and demand for shipping tonnage will widen thanks to a sharp increase supposed to emerge in the demand for overseas coal in the future and that a scarcity of tonnage will impede stable space securing for coal and economically viable coal transportation. Such being the case, this project aims to investigate the ocean freight systems to serve between overseas coal shipping ports and Japan's coal receiving bases and the current states and problems of cargo facilities in Japan, to study how to build up a shipping space securing system which will properly deal with an increase in the import of steam coal from abroad, and to contribute to the formation of measures for enabling smooth transportation of coal from overseas. The survey conducted for this purpose covers the present conditions of Japan's ocean freight systems and of its coal receiving bases, present conditions of transportation by oceangoing ships in the Pacific basin, compilation of a list of oceangoing ships, prediction of ocean freight transportation and supply of transportation service, prediction of ocean freight cost in the future, and putting in an easy-to-review order the tasks to be accomplished for the enhancement of coal transportation by oceangoing ships. (NEDO)

  7. FY 2000 report on the survey on the future development of high grade board forming simulation technology; 2000 nendo kodoban seikei simulation gijutsu no kongo no tenkai ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving energy conservation by reducing weight of vehicles, survey was made of forming/processing technology of new materials such as high-tensile steel and aluminum alloys, and the future development was studied of 'high grade board forming simulation technology.' The subject of the board forming simulation is to develop a method to precisely predict dimensional accuracy (mainly spring back) and sectional shape. When applying the forming simulation technology to difficult-processing materials such as high-tensile steel and aluminum alloys and unknown materials such as super metal, subjects seem to remain in the predicted accuracy because the material models used do not describe characteristics of these materials. The important subject is to upgrade the forming simulation of difficult-processing materials and unknown materials such as by precisely describing plastic anisotropy and instable phenomena of materials into the shape suitable for difficult-processing materials. The subject is also the development of the continuous simulation technology including a series of more than one processes in press processing - welding assembly - strength analysis. (NEDO)

  8. Fiscal 2000 report on results. Development of technology for intermediate processing system for recycling mixed waste plastics; 2000 nendo kongo haipra saishohinka no tame no chukan shori system gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted concerning intermediate processing technology for recycling mixed waste plastics, a technology for processing household waste plastics such as plastic containers and packaging into plastic pellets of suitable grain sizes, with fiscal 2000 results compiled. In the development of the element technologies, an air clutch structure was added that generates rotor slip when foreign matters were engaged, thereby unnecessitating pre-sorting work for locating and removing metallic foreign matters. Addition of an air separator and a sieving machine also helped to achieve a useful-plastics recovery rate of 75% or more in the PVC separation equipment. In the operation of a demonstration plant, a continuous operation was carried out in a three-shift 24-hour system for five days, with the data obtained. Further, waste plastics to which the Containers and Packaging Recycling Law was applicable were treated, resulting in the processing capacity of 0.51 t/h and the production capacity of 0.38 t/h, which both exceeded the target. In the evaluation of the intermediate processing system, the cost of waste plastics treatment turned out to be about 50,000 yen per ton in the case of a plant having a processing capacity of 6,000 tons per year and about 30,000 yen per ton in the case of a plant of 24,000 tons per year. (NEDO)

  9. Report on achievements in fiscal 1998. Development of an interim processing technology to re-commercialize mixed waste plastics; 1998 nendo kongo haipura saishohinka no tame no chukan shori system gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    The container and package recycling law is fully enforced starting fiscal 2000. Recycling obligation is placed also on plastic containers and packages discharged from households, excepting PET bottles for beverages and soy sauce. Therefore, it is required to establish an interim processing technology to process these materials into shapes easy for re-utilization and transportation, that is a technology to manufacture granules with adequate diameters. The purpose of this research is to develop the interim processing system technology. Design, fabrication and installation were performed on an interim processing system plant (a mixed waste plastic granule manufacturing facility) that can process annually waste plastics of 3,000 tons (0.5 t/h). The plant consists of the following four pieces of equipment: (1) a pulverizer, (2) a PVC sorting device, (3) a granulating device, and (4) a sizer. After the installed interim processing system demonstration plant has been trially operated and adjusted by each device, the whole plant was given the trial operation and adjustment to have verified that all the devices function normally. In addition, in order to evaluate economy of the waste plastics interim processing, the processing cost was calculated and the economic performance was evaluated preliminarily by using the rated electric power setting and trial operation data of each device. (NEDO)

  10. FY 1999 report on the results of the development of the preparation system technology for recycling of mixed waste plastics; 1999 nendo seika hokokusho. Kongo haipura saishohinka no tameno chukan shori system gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By operating the demonstrative plant for the preparation system to recycle mixed waste plastics and process them into such a shape that the transportation can be easier, conducted were the development of element technology necessary for the preparation and the evaluation study of process cost, economical efficiency, environmental effects, etc. The FY 1999 results were summed up. As to the operation of the demonstrative plant for the preparation completed in September 1999, the target waste plastic processing capacity of 3,000 t/y was expected to be achieved. Further, conditions were obtained for effectively separating/removing metal foreign matters such as iron and aluminum and heavy materials such as glass and plaster and for separating/removing chlorine resins such as PVC and reducing the chlorine concentration of the agglomerate to 2% or below. Concerning the development of the agglomeration technology by frictional heat, the target processing capacity of about 350 kg/h was expected to be achieved. In the plant assumed of the actual machine of process capacity of 6,000 t/y, the waste plastic processing cost was estimated to be about 70,000 yen/t. Moreover, the CO2 emission reduction amount of the agglomerate by coke substitution was quantitatively evaluated. (NEDO)

  11. How large-scale technological development should be in the future. Survey and research on highly automated machines; Kongo no daikibo gijutsu kaihatsu no hoko ni tsuite. Kodo jidoka kikai ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A survey is conducted about highly automated machines such as industrial robots. The task to be subjected to development as derived from a survey conducted about needs is the construction of a dangerous work robot. It is pointed out that work in coal mines, tall buildings, industrial complexes, or nuclear power plants may encounter large-scale accidents, and the task is how to perform such work in an automated way. The tasks concluded to be subjected to development after a seed survey analysis are categorized into three groups of element technologies, namely, sensors and recognition function, mechanism and materials, and control and data processing. These element technologies are to be ultimately integrated into a robot, for critical work which is a combination of a highly intelligent robot main body and an integrated management system. Since it will happen that humans have to directly operate such a robot under delicate conditions and share the burden of judgement and thinking, it is also necessary to develop technologies to solve problems of man-to-robot engineering. It is proposed that a dangerous work robot research and development program be established before development is started. (NEDO)

  12. Present state and future of pretrochemical industry; Domestic and overseas situations concerning new and additional construction of facilities of ethylene and BTX. Sekiyu kagaku sangyo no genjo to kongo; Ethylene BTX no shinzosetsu wo meguru naigai josei

    Energy Technology Data Exchange (ETDEWEB)

    Konuma, Yoshio

    1990-02-25

    Since 1987, petrochemical industry has jumped into the era of properity and as a whole, been supported by increasing demands. Although it is said that the 21st Century is the age of chemistry, but for petrochemistry the age of 1990 {prime} s is the age of international competition for the survival towards the 21st Century. The scale of individual enterprise of the Japanese chemical industry including petrochemical enterprises still remains small when compared with that of the individual world-wide chemical enterprises of the U.S.A., Germany and the U.K., etc., besides these world-wide enterprises have established their production bases and research facilities in Japan. In addition, there is somewhat uncertainty in the foundation which is supporting the present prosperity. This article scans the present situation of petrochemistry in its preface, explains the present state and trends of individual industry in the chapters covering the environment around the Japanese petrochemical industry, the report (summary) of the Long Term Credit Bank Institute of Management, trends of advance of oil industry into petrochemical business, production capacity of ethylene and new as well as additional plant construction plans. In this industry, is observed the constitution of Japan which is unable to form internationally competitive power irrespective of her recognition of its necessity because of their giving priority to the balance of their business world. 1 tab.

  13. Characteristics of mixed culture where one type of microorganism assimilates the metabolite; Isshurui no biseibutsu ga seiseisuru taishabutsu wo betsuno shuruino biseibutsu ga shikashite zoshokusuru kongo baiyo no moderuka to tokusei kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Toyama, M.; Matsunaka, T.; Shimizu, K. [Kyushu Inst. of Tech., Fukuoka (Japan). Dept. of Biochemical Engineering and Science

    2000-11-10

    Unstructure models were developed for a mixed culture where one microorganism assimilates the metabolite produced by another microorganism The model system was a mixed culture using Lactobacillus delbrueckii and Ralstonia erthroprop where the former assimilates glucose and produces lactic acid, and the latter assimilates lactate and produce poly {beta}-hydroxy butyrate (PHB). Performance improvement is shown for the mixed culture over a single culture for chemostat using the model developed. Since the optimal dissolved oxygen (DO) concentration is different for each microorganism, we developed another model which takes into account the effect of DO concentration on the dynamic behavior. Then the optimal DO concentration is obtained for chemostat. Moreover, we developed another model which takes into account NH{sub 3} concentration on the cell grown and PHB production by R. eutropha. Then the optimal time-profile for NH{sub 3} concentration is derived using the maximum principle. It is found that high Phba production could be attained even if NH{sub 3} concentration is not controlled if initial NH{sub 3} concentration is appropriately selected. (author)

  14. Determination of electron impact ionization and excitation coefficients in He-Xe gas mixtures. He-Xe kongo gas ni okeru denshi shototsu denri keisu oyobi reiki keisu no sokutei to kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Tachibana, K. (Kyoto Inst. of Technology, Kyoto (Japan))

    1991-03-20

    The rare gas discharge gives a stable discharge and light emission characteristics at low temperature in comparison with the discharge of the vapor of such a metal as Hg. The present barrier for the commercialization of the color PDP lies in the lower level of its emission intensity and efficiency in comparison with that of CRT. In this report, an electron impact ionization coefficient in a gas mixture and an electron impact excitation coefficient for a XeIs {sub 4} level were analyzed using a Boltzmann equation by means of a steady state Townsend method using a drift tube. By comparing both, the elementary process in the gas mixture is investiagted to discuss the respective contributions for the effective ionization coefficient and the excitation coefficient. As a result, it was found that the ionization process in the He-Xe gas mixture could be described by the processes of direct ionization of Xe and He, and an indirect ionization (Penning effect) by an active helium. 37 refs., 12 figs.

  15. FY 1998 annual report on the survey on promotion of overseas coal importation bases. Prospects of future export prices of steam coal; 1998 nendo kaigaitan yunyu kiban seibi sokushin chosa. Ippantan yushutsu kakaku no kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey was conducted to analyze the future trends of export prices of steam coal and thereby to contribute to security of stable supply of coal by collecting overseas information from relevant organizations, e.g., history of coal futures transactions in USA, and backgrounds, trends and evaluation thereof; and correspondence of the Australia's government and coal industry to depressed coal prices, actual situations of the country's mining industry and coal production, and their opinions on coal transaction contracts. Australia is the most important and hence influential coal supplier for Japan, and the country's coal industry is now in shaky conditions of reorganization. Chapter 1 describes shift from benchmark transactions to individual negotiations to determine steam coal prices since FY 1998, Chapter 2 takes up trends of coal futures transactions the US markets are adopting, Chapter 3 analyzes trends of steam coal prices in Australia, and Chapter 4 prospects future trends of steam coal markets and prices in Australia. The future coal prices will fluctuate periodically, but will be generally subjected to downward pressure in the medium term. (NEDO)

  16. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  17. Survey on the present situation and future outlook of energy/environment issues mainly on coal in the APEC region; APEC ikinai no sekitan wo chushin to suru energy kankyo mondai no genjo oyobi kongo no mitoshi ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    For the purpose of studying the energy supply/demand trend and the environmental problem relating mainly to coal in the APEC region, the paper surveyed the situation from the past to the present and outlooked the beginning of the 21st century. GDP in the whole APEC region increased at an annual rate of 3.4% from 1971 to 1991 and made a rapid growth of an annual rate over 7% especially in the non-OECD region. The supply/demand balance of coal, etc. in the non-OECD region is expected to be tight, and the energy price also to be higher. This will be a major factor causing hindrance to the economic growth of resource-importing countries. It is necessary to prepare the energy infrastructure. With the increasing coal utilization, it is feared that pollutants such as SOx, NOx and CO2 will increase, and it is necessary to introduce energy utilization technology/facilities which are high-efficient and environment-friendly and to expedite introduction of non-fossil energy. The APEC region, where the worldwide growth is expected, is a priming for the world development, and a policy which is well balanced in economic growth, stabilized energy supply, and environmental protection is needed for the region to achieve its sustainable growth. 50 figs., 24 tabs.

  18. Research report on the effect of the large-scale industrial technology development system and on how it should be in the future; Ogata kogyo gijutsu kaihatsu seido no seika oyobi kongo no arikata ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    A survey was done about projects implemented under the above-named development system inaugurated in fiscal 1966, and studies are made as to how large projects should be in the future. The survey covered the subjects which had been completed by fiscal 1985, that is, the remotely controlled submarine drilling device for oil, seawater desalination and by-product utilization, electric vehicle, technology of comprehensive control of automobiles, pattern information processing system, direct iron making by use of high-temperature reduced gas, manufacture of olefines from heavy oil, aviation jet engine, resources recycling/reuse system, superhigh-performance laser-aided combined manufacturing system, submarine oil production system, and the optics-aided measurement/control system. Answers were heard from corporations concerned. The answers contained some complaints, concerning the shortage of experience on the part of participating corporations, degradation in planning functions, increase in the burden of leading companies, shortage of study or conference about an optimum promotion system, problems in accounting and auditing systems, etc., and suggestions were presented for improvement on large-scale projects. (NEDO)

  19. Fiscal 1999 survey report. Survey on use of reproducible energy in Oceania and on feasibility of future introduction; Oseania ni okeru saisei kano energy riyo jokyo to kongo no kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Survey was conducted on the actual state and the potentiality of reusable energy (RE) in the South Pacific nations. The countries to be surveyed were Australia, New Zealand, Papua New Guinea, the Fiji, the Republic of the Marshall Islands, and the Republic of Nauru. The subject RE are photovoltaic power (PV), solar heat, wind force, biomass, hydraulic power and geotherm. The survey items were as follows; RE policy and promotion programs, technical level of makers, RE supply areas and population for independent/linking type electric power systems, population of non-electrification areas, meteorological data, foreign investment policy, feasibility for introduction if RE not yet introduced, and potential of promotion if RE already introduced. Propositions are as follows. Australia and New Zealand, having a comparatively large population and a stable government, are the two most important markets for RE technologies. The South Pacific nations have a markedly small population, providing a limited market for RE systems. Papua New Guinea, being a country possessing natural gas resources, has a chance of developing photovoltaic and fossil energy hybrid systems. The Fiji shows possibility for hydraulic, wind force and biomass power generation. (NEDO)

  20. Numerical simulation of growth of flames formed in two-dimensional mixing layer. 2nd Report. Effect of dilution of fuel; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 2. Nenryo no kishaku ni yoru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Noda, S [Toyohashi University of Technology, Aichi (Japan); Hashimoto, K [Sumitomo Metal Industries, Ltd., Osaka (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

    1994-07-25

    The effect of fuel dilution on growth of flames formed in 2-D mixing layers was studied by numerical simulation. The methane mass fraction of fuel was adjusted to 1.0, 0.3 and 0.2 through dilution by nitrogen, while the oxygen mass fraction of an oxidizer was fixed at 0.27. Flame structure was complicated due to the flows separated by flame at the leading edge of flames, and three peaks of the second Damkohler number were observed. Fuel dilution by nitrogen caused blow-off of flames, and the mixing ratio of the fuel and oxidizer at the leading edge of flames was essential to blow-off of diffused flames. In the case where vortices were observed in a flow field, the first Damkohler number was important which was determined by the hydrodynamic characteristic time of coherent vortices and the chemical characteristic time of flame propagation based on the mixing ratio of the fuel and oxidizer at the leading edge of flames. The diffused flames were elongated by shearing force, and an exothermic reaction was suppressed and a flame stabilization decreased with a decrease in second Damkohler number. 10 refs., 9 figs., 1 tab.

  1. Accomplishments hitherto achieved regarding the development of solar cell manufacturing technologies and the future course. Annex; Taiyo denchi seizo gijutsu kaihatsu no koremade no seika to kongo no hoko. Fuzoku shiryo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-07-01

    Collected in this paper are the results of evaluation and studies which were conducted, regarding the development of solar cell manufacturing technologies, by the Solar Cell Manufacture Evaluation Sub-Committee at its 4 meetings held in the period from May to August, 1985. For the development of technologies of manufacturing solar cells under the Sunshine Program, the development of technologies for manufacturing crystalline solar cells and amorphous solar cells is required. The Industrial Technology Council, Ministry of International Trade and Industry, in August, 1982, set intermediate goals to be achieved by fiscal 1985. To be developed for the practical application of crystalline silicon solar cells are a low cost experimental silicon refining system and an experimental solar panel manufacturing system. To be carried out for amorphous solar cells are basic studies including a study of physical properties, the development of a large-area high-efficiency solar cell manufacturing technology, and the development of a low cost monosilane manufacturing technology making use of molten salt electrolysis in a closed cycle. In fiscal 1984, 90% of the goals were attained, and now it is expected that almost all will be complete within fiscal 1985. (NEDO)

  2. Fiscal 1996 survey of the base arrangement promotion for foreign coal import. Subject on stable supply of Australian coal in the future; 1996 nendo kaigaitan yunyu kiban seibi sokushin chosa. Kongo no Goshutan no antei kyokyu no kadai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper analyzes coal resource reserve in Australia, environmentally restrictive conditions of the coal resource development and effects on the supply, forecast of the supply ability of Australian coal as viewed cost competitivity, and the export market of Australian coal and supply forecast, and arranged subjects in the future long-term stable supply. Regions where Australian coal resource exists are mainly states of New South Wales (NSW) and Queensland (Qld), which have 76 billion tons of the measured reserve. In the NSW state, about 50% of the coal reserve are not minable. Approximately 30%, 13% and 6% of the resource are restricted by the national park, farmland and others, respectively. The Qld state is little influenced by the national park and the native title land claim. The coal production in 1995 was 229 million tons, and the export 137 million tons. The production capacity was around 350 million tons including plans for expanding the existing coal mines and plans for new development of coal mines. Cost competitivity of Australian coal is higher than that of US western coal. Coal resource in Australia is huge in volume, existing near the seashore. Harbors for shipment can be easily expanded, and therefore there are basically no problems in increasing export. 27 refs., 41 figs., 47 tabs.

  3. Energy and power source mix in East Asia. Restrictions on resource, fund and environment and the future prospect; Higashi Asia no energy dengen mix. Shigen shikin kankyo no seiyaku to kongo no tenbo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-07-01

    In Asian countries, the economic growth rate is extremely higher as compared with the world average, and accordingly a large growth in energy supply/demand and electric power supply/demand is paid attention to. Besides, at users` side, a fear is the worsening of the environmental problem which is brought about by a rapid increase in energy consumption. At suppliers` side, introduction/expansion of a large amount of foreign funds for rapid promotion of power source development become necessary so that supplying facilities catch up with the growth in demand. Moreover, dependence of the supply upon outside the area is becoming higher, and problems in safety guarantee are also becoming prominent. As for energy/power source mix in East Asian countries, the stable supply is basically considered as most important, and economical efficiency is also important including competition conditions among energies and potential raising of investment in supplying facilities. It is no exaggeration to say that the increase in the rate of coal which occupies most of the primary energy supply/power source in East Asian countries depends upon the progress of environmental harmony technology such as clean coal technology. 39 figs., 132 tabs.

  4. Reactive synthesis of Ti-W-Cr-B mixing powder by spark plasma sintering; Hoden plasma shoketsu ni yoru Ti-W-Cr-B kongo funmatsu no hanno gosei

    Energy Technology Data Exchange (ETDEWEB)

    Kaga, H. [Hokkaido Industrial Technology Center, Sapporo (Japan); Carrillo-Heian, E.M.; Munir, Z.A. [University of California, CA, (United States)

    2000-08-15

    The reactive sintered compacts of Ti-W-Cr-B mixed powders were manufactured by a pulse electric current technique. Identification and characterization of the resulting boride phase were done using EPMA, XRD and other methods. The density of the sintered compacts rose rapidly with sintering temperature up to 1,773 K, at which temperature the relative density was 94%. Above this temperature, the density rose only slightly with increasing sintering temperature. The borides of Ti and W were synthesized from mixed metal powders by this method. The type of boride formed and its composition depended on sintering temperature. Compacts sintered at lower temperatures consisted of WB{sub 2} and TiB{sub 2} phases, but at the highest sintering temperature, 2,173K, the main phase was (Ti, W, Cr)B{sub 2} solid solution, in which W and Cr were dissolved in TiB{sub 2}. There was also a very small amount of {beta}-(W, Ti, Cr)B phase. By annealing compact sintered at high temperature, the (Ti, W, Cr)B{sub 2} solid solution phase decomposed and the amount decreased. (author)

  5. Under Familiar Fire: Making Decisions During the “Kivu Crisis” 2008 in Goma, DR Congo Unter vertrautem Feuer: Entscheidungsfindung während der “Kivu-Krise” in Goma, DR Kongo, 2008

    Directory of Open Access Journals (Sweden)

    Silke Oldenburg

    2010-01-01

    Full Text Available This paper explores the decision-making processes used by the inhabitants of Goma during the Kivu Crisis in October 2008. The paper’s aim is twofold: After providing a short history of the October 2008 events, it seeks in the empirical part to distinguish and clarify the role of rumours and narratives in the setting of violent conflict as well as to analyse their impact on decision-making processes. As the epistemological interest lies more on the people who stay rather than those who flee, in the second part the paper argues that the practice of routinization indicates a conscious tactic whose purpose is to counter the non-declared state of exception in Goma. Routinization is defined as a means of establishing order in everyday life by referring to narratives based on lived experiences. Die Autorin des Beitrags untersucht Entscheidungsfindungsprozesse der Einwohner von Goma während der Kivu-Krise im Oktober 2008. Nach einer kurzen Geschichte der Ereignisse wird im empirischen Teil des Beitrags die Rolle von Gerüchten und Erzählungen für die gesellschaftliche Szenerie gewaltsamer Konflikte aufgezeigt und voneinander abgegrenzt und ihre jeweilige Bedeutung für Entscheidungsfindungsprozesse analysiert. Da sich das Forschungsinteresse der Autorin in erster Linie auf den Teil der Bevölkerung richtet, der am Ort des Geschehens bleibt, und weniger auf den, der sich zur Flucht entscheidet, wird im zweiten Teil des Beitrags die Praxis der Routinisierung hervorgehoben, eine bewusste Strategie der Betroffenen, um mit dem nicht-deklarierten Ausnahmezustand in Goma umzugehen. Routinisierung wird als Mittel definiert, die alltägliche Ordnung aufrechtzuerhalten, indem man auf Erzählungen gelebter Erfahrung zurückgreift.

  6. Survey and research report on how large-scale technological development should be in the future; Kongo no daikibo gijutsu kaihatsu no hoko ni tsuite no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-03-01

    Mentioned as data processing technologies to be developed in the 1980s are a computer-assisted system of document translation, supercomputer, knowledge-based information system, and an automated Japanese language office work processing system. Mentioned in relation with the utilization of thermonuclear energy are atomic steel making, liquefied coal gasification, heavy oil gasification, and cracking of heavy oil into lighter oils. In relation with process conversion and new materials technologies, the development and application of functional membrane materials and the conversion of biomass into chemical materials are taken up. In relation with aviation and space technologies, a high-speed turboprop airplane, highly efficient aeroengine, ultralight aircraft, and a transport plane powered by methane or hydrogen are taken up. In relation with electronics or mechanics, an ultra-precision high order production system, automotive ceramic engine, industrial robot system, intelligent database machine system, and a transportable synchrotron are taken up. In addition, a number of subjects are mentioned in relation with social system technology, optoelectronic technology, resources and ocean development technologies, etc. (NEDO)

  7. Fiscal 1992 survey report. Promotion of coal importing base buildup (How ocean freight system should be in the future); 1992 nendo kaigaitan yunyu kiban seibi sokushin chosa. Kongo no gaiko yuso taisei no arikata ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    When a general view is taken of coal chains that connect overseas coal suppliers to Japan's end users, it is found that no survey has ever been made to sufficiently explain marine transportation of coal. It is now expected that the gap between supply of and demand for shipping tonnage will widen thanks to a sharp increase supposed to emerge in the demand for overseas coal in the future and that a scarcity of tonnage will impede stable space securing for coal and economically viable coal transportation. Such being the case, this project aims to investigate the ocean freight systems to serve between overseas coal shipping ports and Japan's coal receiving bases and the current states and problems of cargo facilities in Japan, to study how to build up a shipping space securing system which will properly deal with an increase in the import of steam coal from abroad, and to contribute to the formation of measures for enabling smooth transportation of coal from overseas. The survey conducted for this purpose covers the present conditions of Japan's ocean freight systems and of its coal receiving bases, present conditions of transportation by oceangoing ships in the Pacific basin, compilation of a list of oceangoing ships, prediction of ocean freight transportation and supply of transportation service, prediction of ocean freight cost in the future, and putting in an easy-to-review order the tasks to be accomplished for the enhancement of coal transportation by oceangoing ships. (NEDO)

  8. Survey report for fiscal 1998. Evaluation by industrial circles of the COP3 outcome and their future response (America); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (Beikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Response in America to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) is investigated. Office of Energy Efficiency and Renewable Energy (EE) of America's Department of Energy conducts activities designed to protect environments and supports America's economic competitiveness. The scope of EE activities is quite wide, covering efforts at energy efficiency improvement and renewal energy utilization for all energy consuming sectors involving construction work and equipment for buildings, various industries and public utility works, and transportation. EE also supports and promotes the development of advanced industrial materials, electric vehicles, hybrid vehicles, fuel cells, etc. In the field of renewable energy, it deals with the exploitation of sunlight, biomass, wind force, water power, geothermal energy, etc. It also supports efficiency improvement efforts being undertaken through studies of advanced power transmission and distribution, high-temperature superconduction, energy storage, etc. The said supports are provided not only by Federal Government but also by state governments, and include financial aids. A number of programs are under way, worked out and promoted by the respective bureaus and departments. They are evaluated, protected, and implemented through the partnership of official and civilian organizations. (NEDO)

  9. FY 2000 report on the survey on the future development of high grade board forming simulation technology; 2000 nendo kodoban seikei simulation gijutsu no kongo no tenkai ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving energy conservation by reducing weight of vehicles, survey was made of forming/processing technology of new materials such as high-tensile steel and aluminum alloys, and the future development was studied of 'high grade board forming simulation technology.' The subject of the board forming simulation is to develop a method to precisely predict dimensional accuracy (mainly spring back) and sectional shape. When applying the forming simulation technology to difficult-processing materials such as high-tensile steel and aluminum alloys and unknown materials such as super metal, subjects seem to remain in the predicted accuracy because the material models used do not describe characteristics of these materials. The important subject is to upgrade the forming simulation of difficult-processing materials and unknown materials such as by precisely describing plastic anisotropy and instable phenomena of materials into the shape suitable for difficult-processing materials. The subject is also the development of the continuous simulation technology including a series of more than one processes in press processing - welding assembly - strength analysis. (NEDO)

  10. Report on results concerning development of supermetal technology (FY2000). Innovative manufacturing technology for iron-based mesoscopic structured material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Tetsu kei mesoscopic soshiki seigyo zairyo sosei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of establishing innovative manufacturing technology for microstructure steel having a crystal grain size of about 1 {mu}m or less and a dimensional thickness of 1 mm or more by homogeneous multi-phase structure steel making, R and D was conducted, with fiscal 2000 results compiled. This year, R and D, using a multi-functional integrated test rolling mill, resulted in obtaining ultra-fine grained steel, a steel plate of 5 mm in thickness and 100 mm in width with grains of 1 {mu}m or less homogeneously in the thickness direction. In the investigation on the characterization by the steel plate sample thus obtained and on the method for preventing degradation in elongation, it was proved that an ultra-refined microstructure containing martensite or austenite as the secondary phase has a suppressing effect on the degradation in elongation. Further, examination was made on the widening of a process window for the practicability in the future and on the optimization of large strain deformation conditions. In the method of analyzing and evaluating ultra-refined microstructures, an analysis technology such as an in-lens SEM was proved to be extremely effective on the analysis of microstructures of supermetals created by large strain deformation as well as on the observation of microstructures of a submicron level. (NEDO)

  11. Fiscal 1998 research report. R and D on super metal (Al system mesoscopic texture-controlled material); 1998 nendo seika hokokusho. Super metal no gijutsu kaihatsu (aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For development of Al materials with superior industrial characteristics (strength, corrosion resistance), this research has promoted development of large-size Al system materials with mesoscopic crystalline texture by high- strain accumulation control technology, and recovery and recrystallization control technology. In this fiscal year, (1) basic study on high-strain accumulation control technology, (2) study on a formation mechanism of ultra- fine crystal grains, and (3) development of a machining process were made. In (1), basic study on low-temperature rolling and study on rolling by rollers having different peripheral speeds were made. In (2), study on refining of recrystallized grains of 5000-base and 7000-base alloys was made. In (3), a low-temperature rolling equipment, and a ultra-rapid heating device were introduced. For the whole R and D project on super metal, the main research facilities such as a low-temperature rolling body for high- strain accumulation and a high-strain accumulative structure formation equipment (melt rolling equipment) for uniform nucleus formation in recrystallization were introduced to gain a firm foothold for the future application research. (NEDO)

  12. FY 2000 Report on survey results. Curtailment of the carbon dioxide emission by effective use of woody biomass system waste; 2000 nendo mokushitsu biomass kei haikibutsu no yuko riyo ni yoru nisanka tanso haishutsu no sakugen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    It is estimated that the woody biomass resources in Japan total 42.70 million t/y on a dry basis (indigenous production: 20.00 million t/y), which corresponds to 18.00 million t/y as oil. This project studies effective utilization of low-quality biomass resources now discarded, e.g., thinning materials and demolition woods, by reference to biomass utilization pursued in European and North American countries. The study activities cover the 3 areas of woody biomass wastes, current status of biomass utilization technologies in the overseas countries, and feasibility of introduction of the utilization technologies, after investigating necessity of abatement of the green-effect gases, current status of energy demands and policies, and woody biomass. Utilization of biomass resources for low-temperature heat purposes, which is the central issue in Japan, is not well established both technologically and politically. Moreover, the biomass resources are not exposed to price competition. Based on these premises, a total of 6 scenarios are proposed to promote utilization of biomass resources, including power/heat co-generation at a wood processing center, and dual firing at existing coal-fired boilers. (NEDO)

  13. Humidity-sensitive characteristics of PbCrO4-PbO thick film elements. PbCrO4-PbO kei atsumaku soshi no kanshitsu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, F [Shonan Institute of Technology, Kanagawa (Japan); Nanba, N [Kantogakuin University, Tokyo (Japan)

    1992-12-20

    This paper describes humidity-sensitive characteristics, which depend on the host composition being PbCrO4 or Pb2CrO5, in the system PbCrO4 combined with various oxides, such as Al2O3, Fe2O3, ZrO2, SnO2, TiO2, ThO2, and Ta2O5. In order to confirm the predominant phase over elements in the system PbCrO4-PbO, the effect of composition and microstructure on the humidity-sensitive characteristics of thick film elements were examined. Consequently, it was found that the humidity-sensitivity in low humidity region increased as the host composition of elements changed from hydrophobic PbCrO4 to hydrophilic Pb2CrO5. It was also shown that these results can be interpreted by a humidity-sensitive mechanism proposed for hydrophilic Pb2CrO5. Furthermore, an absorption model of H2O molecules on to the surface of Pb2CrO5 in the PbCrO4-PbO system humidity sensor was provided. 4 refs., 12 figs.

  14. Report on results concerning development of supermetal technology (FY2000). Development of technology for aluminum-based mesoscopic-structured metallic material; Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Aluminium kei mesoscopic soshiki seigyo zairyo no gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength alloys through grain refinement, R and D was conducted, with fiscal 2000 results compiled. This year, using hot rolled plates and cold rolled plates of 5083 based alloys, research was carried out on an optimum warm processing method for forming microstructures. When 5083 alloys were rolled with a large reduction by one pass under a warm to hot temperature range, recrystallized grain structures were obtained having 3-4 {mu}m in the surface and 7-8 {mu}m in the center. The proof stress of these specimens was about 1.3 times as strong as an ordinary 5083 alloy soft material while the elongation was about the same. In the case of 7475 based alloys with Zr added in place of Cr, a warm rolling method, in which the alloys were heated to 350 degrees C and repeatedly reheated by one pass at that temperature, was found effective in forming micro-subgrain structures. By the warm rolling method in which roll temperature was suitably heated, it was made possible to steadily form thermally stable microstructures in 7475 based alloys. The 7475 based alloy plate having a microstructure is superior to an ordinary 7574 plate in resistance against stress corrosion cracking. (NEDO)

  15. Fiscal 2000 report of investigation. Research on effective use of technology for biomass waste and diffusion scenario of the technology; 2000 nendo biomass kei haikibutsu no yuko riyo gijutsu to sono fukyu scenario no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Examination and proposal were made on the effective uses of technologies for biomass wastes and on the diffusion scenarios, with trial calculations done to find the maximum reducible amounts in terms of carbon dioxide. In the examination of the systems, it was focused on five technologies, namely, direct combustion of straw and rice straw/CHP/heat utilization, synthesis of gasified methanol from demolition wood, biogas/CHP from livestock feces and urine, conversion to ethanol through saccharification of used paper, and conversion to biodiesel from vegetable waste oil; the examination also covered each feature, core function, use situation inside and outside Japan, technological system for each energy conversion, etc. Further, solutions were examined and proposed concerning diffusion barriers in each scenario. Consequently, the maximum amount of CO2 reduction effect was found respectively 217 thousand t-C in the straw and rice straw, 500 thousand t-C in the demolition wood, 9.53 million t-C in the livestock feces/urine, 820 thousand t-C in the used paper, and 30 thousand t-C in the vegetable waste oil. (NEDO)

  16. Research and development of photovoltaic power system. Study on structural defects in silicon-based amorphous materials; Taiyoko hatsuden system no kenkyu kaihatsu. Amorphous silicon kei zairyo no kozo kekkan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T [Kanazawa University, Ishikawa (Japan). Faculty of Engineering

    1994-12-01

    Described herein are the results of the FY1994 research program for structural defects of silicon-based amorphous materials for solar cells. The study on light generation defects of the a-Si:H system and rejuvenation process by annealing establishes the effects of light irradiation time on changed neutral dangling bond density as a result of light irradiation at varying temperature of 77K, room temperature and 393K. The study on annealing to rejuvenate light generation defects of various types of a-Si-H systems establishes the activation energy distribution with respect to annealing to remove light-induced defects, showing that hydrogen affects the distribution of light-induced defects. The study on decaying process of light-induced ESR for undoped and N-doped a-Si:H systems observes the decaying process of light-induced ESR, after light is cut off, extending for a period of several seconds to several hours at 77K for the a-Si-H systems containing N in a range from 0 to 12at%. The other results presented are space distribution of neutral defects of light-irradiated a-Si-H systems, and rejuvenation process of light-induced spin for the a-Si(1-x)N(x):H composition. 6 figs.

  17. Preparation of amorphous-crystalline SiO{sub 2} composite by hot isostatic pressing (HIP). 2; HIP ho ni yoru SiO{sub 2} kei hishoshitsu-kesshoshitsu fukugo zairyo no sakusei. 2

    Energy Technology Data Exchange (ETDEWEB)

    Ito, S.; Nishii, J.; Fujii, T.; Akashi, K. [Science University of Tokyo, Tokyo (Japan). Faculty of Science and Tecnology

    2000-08-15

    The composites consisting of {alpha}-quartz crystallites and amorphous SiO{sub 2} were prepared by HIP technique, imitating the structure of natural agate. In the previous study, the K{sub IC} of the composite prepared from the mixed powder of crystallites and amorphous SiO{sub 2} was comparable to that of the natural agate (0.56MN/m{sup 1.5}). In this study, to increase the toughness of the composite, (1) the mixture of silica sol and {alpha}-quartz powder and (2) silica sol including nucleation promoter were examined as starting materials respectively. These starting materials were pressed into powder compacts with {phi} 10 multiplied 50mm in size. The Pyrex glass capsule containing the compact was hipped at 800-1,200 degrees C for 0-120 minutes under the pressure of 200 MPa. The K{sub IC} of the composite obtained from the mixture of silica sol and {alpha}-quartz powder was equivalent to that obtained in the previous study, while the maximum K{sub IC} (0.63 MN/m{sup 1.5}) was obtained when PbCl{sub 2} was used as a nucleation promoter. The nucleation promoter having low solubility in water was useful for the homogeneous generation of the crystallites. (author)

  18. BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

    1996-10-28

    On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

  19. FY 1997 report on the improvement of toughness of silicide system intermetallic compounds by complex texture; 1997 nendo chosa hokokusho (fukugo soshikika ni yoru silicide kei kinzokukan kagobutsu no kyojinsei kaizen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop new materials superior in both room- temperature ductility and high-temperature strength, the basic data on MoSi2 intermetallic compounds with complex texture were stored. Intermetallic compound is one of the promising candidates of new super heat-resistant materials superior to conventional super heat-resistant alloys, however, it is extremely poor in ductility at room temperature. Based on available information on isothermal sectional phase diagrams of ternary system (Mo-Si-X system) composed of Mo silicide and the third element (X), some alloy systems were selected in consideration of use of carbide and nitride stably existing as dispersed phase of deposits at high temperature. A knowledge on phase diagrams of ternary system specimens with various compositions was obtained through arc melting, X-ray diffraction and texture observation, and heat treatment conditions for obtaining target complex textures were also determined. Storage of the basic data suggested that improvement of the ductility is possible by forming fine texture through addition of the third element and teat treatment. 21 refs., 58 figs., 15 tabs.

  20. Corrosion resistance and protection mechanism of hot-dip Zn-Al-Mg alloy coated steel sheet under accelerated corrosion environment; Yoyu Zn-Al-Mg kei gokin mekki koban no sokushin fushoku kankyoka ni okeru taishokusei toi boshoku kiko

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, A.; Izutani, H.; Tsujimura, T.; Ando, A.; Kittaka, T. [NKK Corp., Tokyo (Japan)

    2000-08-01

    Corrosion behavior of hot-dip Zn-6%Al 0-3%Mg alloy coated steel sheets in cyclic corrosion test (CCT) has been investigated. The corrosion resistance was improved with increasing Mg content in the coating layer, and the highest corrosion resistance was observed at 3% Mg. In Zn-6%Al-3%Mg alloy coated steel sheet, the formations of zinc carbonate hydroxide and zinc oxide were suppressed for longer duration compared with Zn-0.2%Al and Zn-4.5%Al-0.l%Mg alloy coated steel sheets. As a result, zinc chloride hydroxide existed stable on the surface of the coating layer. From the polarization behaviors in 5% NaCl aqueous solution after CCT, it was found that the corrosion current density of Zn-6%At-3%Mg alloy coated steel sheet was much smaller than those of Zn-0.2%Al and Zn-4.5%Al-0.1%Mg alloy coated steel sheets. As zinc carbonate hydroxide and zinc oxide had poor adhesion to the coating layer and had porous structures, these corrosion products were considered to have little protective action for the coating layer. Therefore, it was concluded that Mg suppressed the formation of such nonprotective corrosion products. resulting in the remarkable improvement of corrosion resistance. (author)

  1. X-ray diffraction study on microstructure of Li20-TeO2 glasses; Xsen kaisetsuho ni yoru Li{sub 2}O-TeO{sub 2} kei garasu no mikuro kozo kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Iwadate, Y; Hattori, T; Nishiyama, S; Fukushima, K; Sugawara, Y [Chiba Univ. (Japan); Noda, K. [Japan Atomic Energy Research Inst., Tokyo (Japan)] Tatsumisuna, M. [Osaka Prefectural Univ., Sakai (Japan)] Umesaki, M. [Osaka Industrial Research Inst., Osaka (Japan)

    1998-07-10

    Li2O-TeO2 glasses attract attention because of unique properties such as high density, high refractive index, large dielectric constants and high infrared transmittance. The short range structures of two samples of Li2O-TeO2 glasses (15:85 mol% Li2O-TeO2 and 25:75 mol% Li2O-TeO2) were investigated by X-ray diffraction technique. Interpretation of the obtained radial distribution functions was performed on the basis of the strength comparison method. The following conclusions were obtained: Two types of Te-O bond lengths of 0.18nm and 0.20nm are found in TeO4 tetragonal bipyramid. As network forming units, the TeO4 tetragonal bipyramids and TeO3 trigonal bipyramids are observed. The TeO4 tetragonal bipyramid units are transformed into the TeO3 trigonal bipyramids through the transient species of polyhedral with non-bridging oxygen atoms with increasing content of Li2O. The lone pair of Te atom does not contribute to the formation of the glass network. 17 refs., 6 figs., 2 tabs.

  2. Electrical conduction of glasses in the system Fe2O3-Sb2O3-TeO2; Fe2O3-Sb2O3-TeO2 kei garasu no denki dendo

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Honghua; Mori, H; Sakata, H; Hirayama, T [Tokai Univ., Tokyo (Japan). Faculty of Engineering

    1995-01-01

    In this study, taking into consideration that TeO2 is a component of the glass network and Sb2O3 shows the redox effect in the glasses reducing its possibility of transformation of Sb{sup 3+} to Sb{sup 5+} as well as glass basicity, highly conductive tellurite based glasses have been prepared by the press-quenching method selecting the Fe2O3-Sb2O3-TeO2 system, and the electroconductive mechanism of the glasses has been examined by measuring its D.C. conductivity {sigma}. Part of the obtained information is as follows; the glass formation range of the Fe2O3-Sb2O3-TeO2 system has been 0 {le} Fe2O3 {le} 15mol%, 0 {le} Sb2O3 {le} 18mol% and 78 {le} TeO2 {le} 100mol% and about 15mol% of the additional amount of Fe2O3 has been the limit of glass formation. As the amount of Fe2O3 has increased, C{sub Fe} has also increased and with this, the linear electroconductivity of the glasses has increased from 1.86 {times} 10{sup -7}S{center_dot}cm{sup -1} to 1.62 {times} 10{sup -6}S{center_dot}cm{sup -1} and the glasses have been confirmed as the n-type semiconductor. The factor determining {sigma} of the glasses has been C{sub Fe} which has increased as the amount of Fe2O3 has increased. 34 refs., 8 figs., 2 tabs.

  3. Synthesis and structure of porous alumina precursors derived from n-alkylamine-AlCl3 system; Chokusa alkylamine-AlCl{sub 3} kei wo mochiiru takoshitsu alumina zenkutai no gosei to kozo

    Energy Technology Data Exchange (ETDEWEB)

    Yoshimura, M.; Machida, M.; Kijima, T. [Miyazaki Univ. (Japan)

    1998-06-01

    Alumina precursors have been prepared from AlCl3 by using n-alkylamines (C{sub n}H{sub 2n+1}NH2) as precipitant at pH 9.6 and pH 6.2, and the structure, composition, microstructure, and thermal decomposition behavior are investigated. The effects of the structure of the precursor on the decomposition behavior and on the surface area of porous alumina are also investigated. When alkylamines n{>=}6 are used, long periodicity phases are produced corresponding to larger than d=2.0nm spacing which can not be attributed to bayerite or pseudo-boehnite. Long periodicity phase is formed uniquely near the water content of about 50mass% (H2O/Al=4.5), and the spacing varies depending on the alkyl chainlength of amine. When the precipitate prepared at pH 6.2 is heated, water is desorbed at near 100degC, pseudo-baehnite phase is pyrolyzed at 300degC, and the precipitate changed into {gamma}-alumina at temperatures higher than 500degC. 16 refs., 9 figs.

  4. Preparation of Bi-Pb-Sr-Ca-Cu-O high Tc thick films on Ag or MgO substrate with superconductor paste; Bi kei ko Tc chodendo paste ni yoru Ag, MgO kibanjo eno atsumaku sakusei

    Energy Technology Data Exchange (ETDEWEB)

    Takabatake, N. [Ishikawa Technical High School, Ishikawa (Japan); Tsubota, T.; Ishikawa, T.; Ohashi, K. [Kanazawa Institute of Technology, Ishikawa (Japan)

    1995-07-15

    The following were reported on making Bi series superconducting thick films by a wet method. A paste was made by adding PSO (or ethanol solution of ethylenegrycol) of Yushiro Chemical Industry Co., Ltd. as a binder to a Bi series 2223 single-phase powder sample (blending composition Bi:Pb:Sr:Ca:Cu=1.8:0.4:2:2:3.2); the sample was then coated on an Ag (or MgO) substrate with a brush; after being dried at 105{degree}C for one hour, it was thermally decomposed at 700{degree}C for one hour; then, the process of prissurized forming (at pressure 2 to 5 ton f/cm{sup 2}) and of sintering at 845{degree}C for 20 hours or more were performed on the sample to form a thick film sample. A critical temperature Tc, critical current density Jc, etc., were measured on such thick film sample. As a result, nearly same values were obtained as Tc (93K) and Jc (84A/cm{sup 2}) which were those of a bulk sample made by using the same powder sample, pressurizing at 2 ton f/cm{sup 2} for pelletizing, and sintering at 845{degree}C for 20 hours. 6 refs., 7 figs., 1 tab.

  5. FY 1994 report on the survey of geothermal development promotion. Complementary survey on the fracture system, etc. (Wasabizawa area); 1994 nendo chinetsu kaihatsu sokushin chosa sogo kaiseki hokokusho futai shiryo. Wasabizawa chiiki danretsu kei tou hokan chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-01

    For the contribution to elucidation of the geothermal structure in the Wasabizawa area, Akita Prefecture, survey by the paleomagnetic measurement and fracture system measurement was conducted of the borehole cores and specimens of outcrop granite obtained from boreholes of N6-WZ-3 and N6-WZ-4. In the survey, the following were carried out: measurement of the core fracture system of N6-WZ-3 (102-1,505m) and N6-WZ-4 (507-1,556m), paleomagnetic measurement of 9 outcrop granite specimens and 16 core specimens, and k/Ar age determination of 3 outcrop granite specimens. As a result of the paleomagnetic measurement of outcrop granite, the magnetization azimuth of the schistose granodiorite distributed in Kuwanosawa was regarded as almost NS. The measured magnetization azimuth of the core specimen obtained from the same rock mass was also made NS-based, and measurement of the fracture in the neighborhood was made. As a result, it was found out that the NNW system was dominant in dikes and that there was the NE system in most of the small geothermal channels. The fracture system of well tended to develop around the boundary between granite and metamorphic rock, and it was thought that this part could be a reservoir if temperature conditions are prepared. (NEDO)

  6. Environmental Forensics

    Science.gov (United States)

    2011-03-29

    1,1- Difluoroethane (HFC-152a) Dibromodifluoromethane (Halon 1202) 1,2-Dichloro-1,1,2,2-tetrafluoroethane (CFC-114) Dib th 1 2 Di hl th (F 150)romome... difluoroethane (HCFC-142b) Dichloromethane (DCM) 2-Chloro-1,1,1,2-tetrafluoroethane (HFC-124) Difluoromethane (HFC32) Dibromotetrafluoroethane (Halon

  7. Development of a compact ECR ion source for various ion production

    Energy Technology Data Exchange (ETDEWEB)

    Muramatsu, M., E-mail: m-mura@nirs.go.jp; Hojo, S.; Iwata, Y.; Katagiri, K.; Sakamoto, Y.; Kitagawa, A. [National Institute of Radiological Sciences (NIRS), 4-9-1 Anagawa, Inage, Chiba 263-8555 (Japan); Takahashi, N. [Sumitomo Heavy Industries, Ltd., 19 Natsushima, Yokosuka, Kanagawa 237-8555 (Japan); Sasaki, N.; Fukushima, K.; Takahashi, K.; Suzuki, T.; Sasano, T. [Accelerator Engineering Corporation, 3-8-5 Konakadai, Inage, Chiba 263-0043 (Japan); Uchida, T.; Yoshida, Y. [Bio-Nano Electronics Research Centre, Toyo University, 2100 Kujirai, Kawagoe-shi, Saitama 350-8585 (Japan); Hagino, S.; Nishiokada, T.; Kato, Y. [Graduate School of Engineering, Osaka University, 2-1 Yamada-oka, Suita-shi, Osaka 565-0871 (Japan)

    2016-02-15

    There is a desire that a carbon-ion radiotherapy facility will produce various ion species for fundamental research. Although the present Kei2-type ion sources are dedicated for the carbon-ion production, a future ion source is expected that could provide: (1) carbon-ion production for medical use, (2) various ions with a charge-to-mass ratio of 1/3 for the existing Linac injector, and (3) low cost for modification. A prototype compact electron cyclotron resonance (ECR) ion source, named Kei3, based on the Kei series has been developed to correspond to the Kei2 type and to produce these various ions at the National Institute of Radiological Sciences (NIRS). The Kei3 has an outer diameter of 280 mm and a length of 1120 mm. The magnetic field is formed by the same permanent magnet as Kei2. The movable extraction electrode has been installed in order to optimize the beam extraction with various current densities. The gas-injection side of the vacuum chamber has enough space for an oven system. We measured dependence of microwave frequency, extraction voltage, and puller position. Charge state distributions of helium, carbon, nitrogen, oxygen, and neon were also measured.

  8. Ozone depleting substances and gases HFCs, PFCs and SF{sub 6}. Consumption and emissions 2003; Ozonlagsnedbrydende stoffer og drivhusgasserne HFC'er PFC'er og SF6. Forbrug og emissioner 2003

    Energy Technology Data Exchange (ETDEWEB)

    Sander Poulsen, T.

    2005-07-01

    The evaluation includes a calculation of actual emissions of HFCs, PFCs and SF{sub 6} in Denmark. In this calculation of actual emissions, the release from stock of greenhouse gases in products has been taken into account, and adjustments have been made for imports and exports of the greenhouse gases in products. The evaluation has partly been prepared to enable Denmark to fulfil its international obligations to provide information within this area, and partly to follow the trend in consumption and emissions of HFCs, PFCs and SF{sub 6}. (BA)

  9. Ozone depleting substances and greenhouse gases HFCs, PFCs and SF{sub 6} consumption and emissions; Ozonlagsnedbrydende stoffer og drivhusgasserne HFC'er, PFC'er og SF{sub 6}. Forbrug og emissioner 2002

    Energy Technology Data Exchange (ETDEWEB)

    Sander Poulsen, T. [Planmiljoe, Veksoe Sjaelland (Denmark)

    2004-07-01

    The aim of the project is to map the 2002 Danish consumption of produced ozone depleting substances and the consumption and actual emission of the greenhouse gases HFCs, PFCs and SF{sub 6}. The inventory is performed, partly according to the guidelines recommended by IPCC (Intergovernmental Panel on Climate Change), and partly according to the method that has been used for previous mappings. The mapping is done partly in order to meet Denmark's international commitments to report and partly in order to monitor how the consumption of ozone depleting substances and the emissions of greenhouse gases develop. The mapping of ozone depleting substances includes the net consumption, meaning the amount of the imported raw materials in bulk or in drums minus any re-export of the substances in the form of raw materials. Mapping of the actual emissions of HFCs, PFCs and SF{sub 6} is done in continuation of previous greenhouse gas inventories. The inventory process is continuously improving due to development of international approved guidelines (IPCC) and the production of increasingly detailed data. (BA)

  10. Random survey of HFC and R22 emission, refrigerants and leakage percentage in the dairy, meat and other food industries; Steekproefonderzoek HFK en R22-emissies, koudemiddelvulling en lekpercentage in de Zuivel, Vlees en Overige voedingsmiddelensectoren

    Energy Technology Data Exchange (ETDEWEB)

    Pennartz, A.M.G.; Van den Bovenkamp, M.V. [KWA Bedrijfsadviseurs, Amersfoort (Netherlands)

    2012-08-15

    The EU member states are obliged to bring the EU F-gas and Ozone policy into operation, by minimalizing the R22 and F-gas emissions in cooperation with market parties. Factors that may guide the refrigerant emission policy are: leakage percentages per year (company level, sector, national level); emission quantities (company level, sector, national level); indirect indicators: knowledge, experience with refrigerating contractors, feed back to end users, proactive prevention by end users. At this moment there is no clear view of the emission percentages in practice with the end users. For this reason the Dutch Ministry of Infrastructure and the Environment, by NL Agency, has initiated a random test survey in the Dairy, Meat and Other Food sectors. The main goal is to obtain data on the size and trends of R22 and HFK emissions in the period 2007-2010 [Dutch] De EU-lidstaten dienen uitvoering te geven aan het EU F-gas en Ozon-beleid, door met de markt te streven naar minimale R22 en F-gas emissies bij de eindgebruikers. Indicatoren (trends) om het koudemiddel emissiebeleid op te kunnen sturen zijn: jaarlijks optredende lekpercentages (per bedrijf, sector, totaal NL); emissiehoeveelheden (per bedrijf, sector, totaal NL); indirecte factoren: kennis/ervaring in lekkagepreventie bij koelinstallateurs, terugkoppeling naar de opdrachtgevers, preventiebeleid/prioriteit vanuit de opdrachtgevers. Tot nu toe ontbreekt een scherp beeld van de optredende lekpercentages (grootte, trends) bij de eindverbruikers. Daarom is door het Ministerie van IenM, via Agentschap NL een steekproefonderzoek uitgezet in de sectoren Zuivel, Vlees en Overige voedingsmiddelen. Doel is een beeld te krijgen van de omvang en trend van de R22 en HFK-emissies over 2007-2010.

  11. Atom-vacancy ordering and magnetic susceptibility of nonstoichiometric hafnium carbide

    International Nuclear Information System (INIS)

    Gusev, A.I.; Zyryanova, A.N.

    1999-01-01

    Experimental results on magnetic susceptibility of nonstoichiometric hafnium carbide HfC y (0.6 0.71 , HfC 0.78 and HfC 0.83 in the range of 870-930 K the anomalies are revealed which are associated with superstructure short-range ordering in a non-metallics sublattice. It is shown that a short-range order in HfC 0.71 and HfC 0.78 carbides corresponds to Hf 3 C 2 ordered phase, and in HfC 0.83 carbide - to Hf 6 C 5 ordered phase. HfC 0.78 carbide is found to possesses zero magnetic susceptibility in temperature range 910-980 K [ru

  12. Haapsalu - Põhjamaade Veneetsia / Viivi Variksaar, Lea Arme

    Index Scriptorium Estoniae

    Variksaar, Viivi, 1948-

    2001-01-01

    ARS Interjöörprojekti kujundatud hotellist 'Kongo', hotelli restoranist. Reet Siimeri algatusel puuetega ja töötute inimeste toetamiseks loodud 'Värkstoast', kus õpetatakse käsitööd ja müüakse käsitööesemeid. Kommenteerinud Liina Aavik

  13. Pushing Back the Origin of Bantu Lexicography: The Vocabularium ...

    African Journals Online (AJOL)

    The manuscript was heavily reworked by the Belgian Jesuits Joseph van Wing and Constant Penders, and published in 1928. Both works are currently being digitized, linked and added to an interlingual and multimedia database that revolves around Kikongo and the early history of the Kongo kingdom. In Sections 1 and 2 ...

  14. A chimpanzee Mega-Culture? Exploring behavioral continuity in Pan troglodytes schweinfurthii across northern DR Congo

    NARCIS (Netherlands)

    Hicks, T.C.

    2010-01-01

    Cleve Hicks deed een vijfjarig veldonderzoek naar het voorkomen van chimpansees in het noorden van de Democratische Republiek Kongo (het Bili-Uelegebied). Hoewel er twijfels bestonden over het überhaupt voorkomen van chimpansees in dit gebied, heeft het onderzoek aan het licht gebracht dat

  15. Toidutööstus panustab detsembris jõulutoodetele. Pühad toovad käibelisa / Ain Alvela, Ketlin Rauk ; kommenteerinud Ruth Roht, Marek Viilol, Simmo Kruustük, Imre Sokk

    Index Scriptorium Estoniae

    Alvela, Ain, 1967-

    2011-01-01

    Spetsiaalsed jõulutooted aitavad aasta lõpul suurendada toiduainetööstuste käivet. ASi Atria Eesti müügi- ja turundusdirektori Margus Masingu, ASi Fazer Eesti juhatuse esimehe Kristjan Kongo ja ASi Salvest turundusdirektori Ain Nõlvaku kommentaare

  16. Vaid klaas vett päevas / Kadri Kalda

    Index Scriptorium Estoniae

    Kalda, Kadri

    2013-01-01

    Rahvusvahelisest koostööprojektist Ghana St Raphaeli algkooli, Valga gümnaasiumi ja EBS-i gümnaasiumiga teemal „Vesi ja sanitaartingimused”. Abistas Põhja-Ghanas Kongo külas töötanud MTÜ Mondo vabatahtlik Diana Tamm

  17. Modified Principal Component Analysis for Identifying Key Environmental Indicators and Application to a Large-Scale Tidal Flat Reclamation

    Directory of Open Access Journals (Sweden)

    Kejian Chu

    2018-01-01

    Full Text Available Identification of the key environmental indicators (KEIs from a large number of environmental variables is important for environmental management in tidal flat reclamation areas. In this study, a modified principal component analysis approach (MPCA has been developed for determining the KEIs. The MPCA accounts for the two important attributes of the environmental variables: pollution status and temporal variation, in addition to the commonly considered numerical divergence attribute. It also incorporates the distance correlation (dCor to replace the Pearson’s correlation to measure the nonlinear interrelationship between the variables. The proposed method was applied to the Tiaozini sand shoal, a large-scale tidal flat reclamation region in China. Five KEIs were identified as dissolved inorganic nitrogen, Cd, petroleum in the water column, Hg, and total organic carbon in the sediment. The identified KEIs were shown to respond well to the biodiversity of phytoplankton. This demonstrated that the identified KEIs adequately represent the environmental condition in the coastal marine system. Therefore, the MPCA is a practicable method for extracting effective indicators that have key roles in the coastal and marine environment.

  18. Report on the survey in fiscal 1998. Evaluation by Industry on the result of COP3 and the future activities (Britain); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (Eikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was carried out to identify the evaluation by British Industry on COP3 and the nation's future activities. In Britain, the gas emission level in 2000 is estimated to achieve sufficiently the initial target as the level is lower by 4 to 8% than that in 1990. This is largely attributable to substitution of coal by natural gas. At the Kyoto Conference, the European Union agreed with its target to reduce the emission of greenhouse effect gas over the period 2008-2012 to 8% below its 1990 level. Britain agreed to share its reduction rate at 12.5%. The Labour Party had set an election pledge since before the general election to reduce carbon oxide emission by 20% (against the 1990 level) by 2010, and the Prime Minister Tony Blair has also confirmed his commitment to this target. The policy making work to achieve the COP3 target has begun in 1998 when the UK Climate Change Program (consultation paper) was issued, and will continue until February 1999. The Advisory Committee of Business and Environment representing British Industry has already published their advice on how to achieve Britain's COP3 objective, which are considered by the government in the above mentioned paper. (NEDO)

  19. Report on 1977 result of Sunshine Project. Test research for detailed design of coal gasification plant (pressure fluidized gasification method for mixed material of coal/heavy oil); 1977 nendo sekitan gas ka plant no shosai sekkei no tame no shiken kenkyu seika hokokusho. Sekitan jushitsuyu kongo genryo no kaatsu ryudo gas ka hoshiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-31

    Since fiscal 1974, development has been implemented for the coal/heavy oil hybrid gasification process which converts coal and heavy oil simultaneously to clean fuel gas. With the purpose of obtaining basic data to be reflected on the detailed design of 7,000 Nm{sup 3}/d pilot plant of the subject process started in fiscal 1977, implemented this year were (1) test on high pressure valves and (2) research on operation studies. In (1), a life test device for high pressure operation valves will be designed and manufactured so that basic materials may be obtained for the development of durable operation valves to be used in a high temperature and high pressure coal/heavy oil slurry feeding device. Operation studies of a low pressure slurry feeding device will be continued, accumulating data required for the design of the coal/heavy oil slurry feeding device. In (2), studies will be started on the operation of a 300{phi}(diameter) internal heat type low pressure gasification device, collecting know-how for the model and design of the gasification furnace of the pilot plant. Gasification experiments will be continued using the high pressure gasification device, so that gasification characteristics under a high pressure will be grasped to examine the optimization of gasification conditions. In addition, a fluidized bed quencher test equipment will be designed and manufactured. (NEDO)

  20. FY 1999 report on the study of the future course, etc. of 'the basic survey for promotion of Joint Implementation, etc.'; 1999 nendo 'kyodo jisshi nado suishin kiso chosa' no kongo no hokosei nado ni kansuru kento chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper conducted the demonstration of the multiplier effect of 'the model project for heightening of the international energy consumption efficiency, etc.' carried out by NEDO and its subsidiary project, 'the project on the basic survey for promotion of Joint Implementation (JI),' and the comparative study between these projects and the JI/CDM projects proposed in the world. In the quantitative evaluation of the multiplier effect, in the case of making the demonstration of the same technology in the same area both in the model project and the basic survey for promotion of JI, it becomes possible to grasp the CO2 reduction effect with high accuracy, but the CO2 reducible amount is small. Inversely, as to the technology for which the basic survey for promotion of JI is studied, but the model project is not carried out, it becomes possible to grasp the CO2 reduction effect with low accuracy, the CO2 reducible amount is large. In the comparison with the JI/CDM projects proposed in the world, the CO2 reduction amount was approximately $2.7 billion, 250 million tons, in the UNFCCC project, and approximately $5.0 billion, 500 million tons, in the IJ project. There was no very big difference in the cost effect. (NEDO)

  1. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  2. Discharge-current characteristics in UV-preionized Kr/He, F2/He gas-mixtures and KrF excimer laser gas. Shigaisen yobi denri Kr/He, F2/He kongo kitai hoden oyobi KrF laser reiki hoden no denryu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nakagawa, N.; Kawakami, H.; Yukimura, K. (Doshisha University, Kyoto (Japan))

    1992-08-15

    In order to study effects of Kr and F2 on discharge characteristics of KrF excimer laser gas, gap phenomena in Kr/He and F2/He gas-mixtures were observed and discharge current (I[sub d]) was measured. In the range where Kr concentration was over 10% in Kr/He gas, in which production of filamentation as well as glow discharge started, discontinuous change in I[sub d] in the second or third half cycle was observed. According to the results of experiments and model analyses, it was considered that the discontinuity of the current showed the transition point to filamentation. When F2 concentration was in the range between 0.1 and 0.3% in F2/He mixture gas, filamentation and arc with glow were observed. Sine-waveform I[sub d] ended in the first half cycle, and began to flow again after cessation or had almost constant current due to arc and others. When F2 was over 0.4%, only are discharge was observed. It was thus found that F2 has a large effect on discharge characteristics of KrF laser gas. 18 refs., 9 figs.

  3. Study on homogeneous charge diesel combustion engine. 4th Report. Search for low emission combustion method with diesel fuel pre-mixture; Kin`itsu kongo asshuku chakka diesel kikan ni kansuru kenkyu. 4. Keiyu yokongoka deno tei emission no kanosei

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Koike, S; Odaka, M [Traffic Safety and Nuisance Research Inst., Tokyo (Japan)

    1997-10-01

    Single fuel operation with diesel fuel has been tried experimentally for the Homogeneous Charge Diesel Combustion method (HCDC). The higher the pre-mixed fuel ratio, the lower the emissions. But diesel knock due to early self ignition may be occurred under high pre-mixed fuel ratio conditions and consequently the maximum pre-mixed fuel ratio is restricted by these knock limits. Full load operations with higher pre-mixed fuel ratio can be possible with a supercharging which improve the knock limits and emissions. 8 refs., 12 figs.

  4. Correlation of dew- and bubble-point curves for binary refrigerant mixtures. [Correlation between dew-point pressure(saturated vapor state) and bubble-point pressure(saturated liquid state)]. Niseibunkei kongo reibai no roten oyobi futten kyokusen no sokan

    Energy Technology Data Exchange (ETDEWEB)

    Yada, N. (Kanagawa Institute of Technology, Kanagawa (Japan)); Watanabe, K. (Keio University, Tokyo (Japan). Faculty of Science and Technology)

    1991-12-25

    The paper makes a correlation expressing dew- and bubble-point curves using measured values for seven binary refrigerant freon-mixtures. In most binary systems at the same temperature, the pressure shows a different value between in a saturated vapor state (dew-point pressure) and in a saturated liquid state (bubble-point pressure). The target is such correlation as has as simple a function form as possible and is able to estimate even near the critical point where it used to be difficult to estimate. The pressure difference between measured values of the dew- and bubble-point pressure and values calculated from Raoult's law showing an ideal mixture of fluid is expressed by a simple function form of reduced temperature Tr and molar fraction. Tr is thermodynamic temperature/critical temperature. Reproducibility of this correlation is less than {plus minus}3% of the pressure deviation. Concerning also the arbitary composition range and near the critical point, the dew- and bubble-point pressure can be calculated accurately. 24 refs., 4 figs., 5 tabs.

  5. Method for laboratory tests on noise emission from appliances used in water supply installations. Part 2:mounting and operating conditions for draw off taps and mixing valves; Kyusui kigu hasseion no jikkenshitsu sokuteiho dai2bu,. Kyusui oyobi kongo suisen no toritsuke houho narabini sado joken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    This standard prescribes the laboratory of the water utensil occurrence sound prescribed with JIS A 1424-1 about the installation method of a water stopper to measure water utensil occurrence sound, and the mixed water stopper and the operation condition by the way of examining it, the test device in the way of measuring it. Or, the water stopper made the target, and a mixed water stopper were decided to be designed by the water pressure of the range of 0.1 - 0.5 MPa so that the building (sink, wash and bathtub) might do the use of the cold water in the neighborhood of the building and the warm water. The valve, which has an automatic temperature adjustment, mixed water stopper; a direct exit to the inside is excluded from the object. Moreover, an electric operation dialect is a combination device and this is excluded from the object. (NEDO)

  6. Numerical simulation of growth of flames formed in a two-dimensional mixing layer. 3rd Report. Flame instability induced by vortices; Nijigen kongo sonai ni keiseisareta kaen no seicho ni kansuru suchi simulation. 3. Uzu ni yotte reikisareru kaen no fuanteisei

    Energy Technology Data Exchange (ETDEWEB)

    Noda, S; Makino, H [Toyohashi University of Technology, Aichi (Japan); Nakajima, T [Kobe University, Kobe (Japan). Faculty of Engineering

    1996-03-25

    The flame instability induced by large vortices has been studied numerically. The numerical simulation is concerned with an unstable, two-dimensional, two-stream, spatially developing, confined, reacting shear layer. The behavior just after ignition is related to the flame instability which is affected strongly by large vortices in the mixing layer. Although flames are basically stable due to the balance between the burning velocity and the stream velocity, it is revealed that the leading edge is exposed under the strain in the mixing layer, and the flame becomes instable. Moreover, a method is also proposed to improve the flame stability by increasing the oxygen concentration in the oxidizer. 13 refs., 6 figs., 2 tabs.

  7. Dopady čínské rozvojové pomoci a investic v Africe se zaměřením na Etiopii a Demokratickou republiku Kongo v letech 2000-2015

    OpenAIRE

    Leová, Leona

    2017-01-01

    The bachelor thesis deals with development aid in general, presents its definition and analyzes in particular the development of various attitudes that were previously discussed. This theoretical background is an essential part of finding more effective approaches, as it can generally be said that the Western assistance to date has failed to do so. The work is thus further dealt with by other development cooperation alternatives that could be capable of 'the poorest' billion out of poverty. T...

  8. Survey and research for the enhancement of large-scale technology development 2. How large-scale technology development should be in the future; Ogata gijutsu kaihatsu suishin no tame no chosa kenkyu. 2. Kongo no ogata gijutsu kaihatsu no arikata

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    A survey is conducted over the subject matter by holding interviews with people, employed with the entrusted businesses participating in the large-scale industrial technology development system, who are engaged in the development of industrial technologies, and with people of experience or academic background involved in the project enhancement effort. Needs of improvement are pointed out that the competition principle based for example on parallel development be introduced; that research-on-research be practiced for effective task institution; midway evaluation be substantiated since prior evaluation is difficult; efforts be made to organize new industries utilizing the fruits of large-scale industrial technology for the creation of markets, not to induce economic conflicts; that transfer of technologies be enhanced from the private sector to public sector. Studies are made about the review of research conducting systems; utilization of the power of private sector research and development efforts; enlightening about industrial proprietorship; and the diffusion of large-scale project systems. In this connection, problems are pointed out, requests are submitted, and remedial measures and suggestions are presented. (NEDO)

  9. Report on the survey in fiscal 1998. Evaluation by the industry on the result of COP3 and the future activities (Germany); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (Doitsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was carried out on activities taken in Germany. The industry has a strong opinion to take voluntary regulations rather than those by laws. The nation's activities are being moved forward centrally with the suppression policies that follow the declaration on the voluntary regulation by the German industry to prevent global warming, which had been submitted by the German Industry Federation to the federal government in 1996. The participation to the declaration, which is optional, covers 71% of the energy consumption by manufacturing industries and 99% of the public electric power consumption, but large-scale industrial departments such as machine and electric power sectors who have not participated can also been found. The plan calls for reduction of inherent CO2 and energy per added value production amount in the entire industry by as much as 20% of the result in 1990 by 2005. According to the third party monitoring system employed by the federal government, the industry submits results of periodical analyses to the government. According to the result, the industries participated in the voluntary regulation have achieved annual exhaust suppression of 42 million tons during the period of 1990 to 1996. The public electric power industrial department whose CO2 emission accounts for a little less than 30% of the nation's total emission amount has a great effect. The industry is making efforts to improve the power generation efficiency aiming at reduction of CO2 emission of 12% of the 1990 result by 2015. (NEDO)

  10. Report on the survey in fiscal 1998. Evaluation by the industry on the result of COP3 and the future activities in relation with the result of COP3 (Canada); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (Canada)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was carried out on activities in Canada in relation with COP3. The Office of Energy Efficiency is promoting the energy efficiency improvement and substituting energy plan applicable to housings, commercial and manufacturing industries, public organizations and transportation department. It is also implementing a comprehensive plan incorporating consumer information, national energy utilization data base, and energy technology innovation initiative. The energy technology innovation plus plan strengthens coordination with industrial societies in each sector, and makes finances for improvement of energy efficiency. There is also an institution to promote energy efficiency improvement in newly built houses. The manufacturing industry energy technology innovation initiative is an institution to present means to transfer pledges in each department into a company-wide activity. In the energy conservation encouragement plan for commercial buildings, an annual federal fund of ten million dollars is allotted, and incentive money is paid. The automotive fuel consumption enhancement plan provides purchasers with fuel consumption information, and encourages production of energy saving cars. The substituting transportation fuel market developing initiative promotes development and utilization of methanol, ethanol, hydrogen, and electric power. (NEDO)

  11. Flow and mixing of gas in cylinder of a stratified charge engine with two intake valves. Effects of late closing valve timing and intake port configurations; Kyuki nibenshiki sojo kyuki engine no cylinder nai gas ryudo to kongo. Osotoji valve timing oyobi port keijo ni yoru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Charoenphonphanich, C; Niwa, H; Ennoji, H; Iijima, T [Tokai University, Tokyo (Japan)

    1997-10-01

    A numerical analysis of the flow and mixing of rich mixture and air inducted into the cylinder through each of the two intake ports of a stratified charge engine have been carried out. Numerical calculations were performed by finite volume method for three types of the intake port configurations: inverse V type, parallel type and V type and two types of valve timing; conventional and late closing (Miller cycle). Velocity field, turbulent kinetic energy and distribution of mixture concentration in the cylinder were examined. 3 refs., 10 figs.

  12. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  13. Research report for fiscal 1998. Industrial circles' evaluation of the outcome of COP3 and their response thereto (France); 1998 nendo chosa hokokusho. COP3 no kekka ni taisuru sangyokai no hyoka oyobi kongo no taio ni tsuite (France)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Since the CO{sub 2} emission reduction cost is high under the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) rulings, they have made it clear that they will positively resort to the flexibility mechanism. This is to reserve a room for freely selecting power generation methods other than nuclear technologies with their nuclear power plants scheduled for renovation in the neighborhood of 2010. But the industrial circles are slow in responding, failing to accept the carbon fund concept. As for measures for greenhouse gas emissions reduction, since they depend on energy saving for their success, the response specially of the transportation division will be the key. In the industrial division, success depends on a voluntary consensus among industries that consume much energy. As steps to economize the trend of people's energy consumption, an energy tax and environmental tax are scheduled to be imposed. An overall program for greenhouse gas emission reduction is being drafted by a government committee, with the outline to be made known in May 1999 for finalization in autumn the same year. A power market liberalization bill has already been prepared, and a decision will soon be made on a plan for the second phase targets. France with take part in COP5, Bonn, Germany, with a general proposal carrying what are stated above. (NEDO)

  14. Research report of fiscal 1997. Research on building up of a NEDO vision (summary of subsidy researches and their future direction); 1997 nendo chosa hokokusho. NEDO vision no sakutei ni muketa chosa (kofukin chosa no matome to kongo no hosaku ni tsuite)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The planning department of NEDO is required to control development sections, and present the basic policy of activities. The department has thus carried out the following subsidy researches: medium/long-range introduction of new energies, study on the NEDO vision, excavation of concrete project seeds and effective use of its result, systematic preparation of basic data on new energy and energy saving. These subsidy researches sums to 480 for the first 17 years. The department now summarized each previous research data for easy understanding, and constructed the system which can systematically arrange data on future subsidy researches. The department also facilitated building up of the NEDO vision by proposing the direction of future subsidy researches, and prepared a database of the subsidy research reports. The trend of the researches was analyzed by systematically classifying the research results, and an easy retrieval system was constructed by giving retrieval codes to each data. The basic direction of a future research policy and effective use of research results is proposed. 23 figs., 7 tabs.

  15. Sustainable prevention of resource conflicts. Case study and scenarios on copper and cobalt in the Democratic Republic of Congo (Report 3.2); Rohstoffkonflikte nachhaltig vermeiden. Fallstudie und Szenarien zu Kupfer und Kobalt in der Demokratischen Republik Kongo (Teilbericht 3.2)

    Energy Technology Data Exchange (ETDEWEB)

    Taenzler, Dennis; Westerkamp, Meike [Adelphi Research, Berlin (Germany); Supersberger, Nikolaus; Ritthoff, Michael; Bleischwitz, Raimund [Wuppertal Institut (Germany)

    2011-04-15

    The Democratic Republic of Congo has enormous economic potential thanks to its raw material wealth. However, since 1996 (if not before) DR Congo has been seen as a classic example of the linkage between the exploitation of raw materials and the financing of war. The UN Panel of Experts on the Illegal Exploitation of Natural Resources in DR Congo points out that the history of Congo since colonial times has been marked by systematic abuse of natural and human resources (UN Panel 2002). The UN Panel of Experts and the work of NGOs have helped to reveal rebels, senior military figures and private companies as profiteers from the exploitation of raw materials and to identify channels of financing the violent conflict in Congo since 1996 (see reports from the UN Panel, Pole Institute, Global Witness, HRW). Foreign companies mining, trading in or processing raw materials in DR Congo have also been regularly criticised as sharing responsibility for the ongoing violence, principally in the eastern Congo (UN Panel 2002, Cuvelier/Raeymaekers 2002, RAID 2004). Practically every major escalation in conflict in recent years between the various players in Congo has been connected to the management of, or the (legal or illegal) revenues from, natural resources, particularly from mining. This observation was also backed by data from the HIIK's CONIS information system. In 2008, eight of nine conflicts in Congo related at least in part to resources - five being violent and three non-violent (HIIK 2008). Following the coltan boom of 2000/2001, it now primarily profits from the mining and sale of the tin oxide ore cassiterite which continue to serve as the key means of financing violence (see Garrett 2008).1 In DRK it is not only the mining and sale of coltan and cassiterite which represents a nexus of conflict and resources however. Alongside timber, diamonds, oil and gold, it is above all the mining and sale of copper and cobalt from the so-called copper belt in the south-east of the southern province of Katanga which is making the security situation in the province unstable. Both copper and cobalt are key raw materials with regard to economic development trends in future technologies: Copper is much in demand among other reasons because of its high electrical conductivity. Cobalt is an essential component material in a range of applications including batteries, superalloys and synthetic fuels. The report is divided into a case study section and four scenarios. The case study analyses the current status quo of the conflict/resources nexus, focusing on potential conflict risks as well as opportunities arising from the situation in 2010. Building on that foundation, the following four scenarios describe various possible developments through to the year 2020. At the end of each scenario the characteristic features of the descriptors are summarised again in tabular form. The conclusions draw together the findings from the case study and scenarios to present the main conflict risks arising in relation to raw material exploitation. (orig.)

  16. Reproductive and developmental toxicity of hydrofluorocarbons used as refrigerants.

    Science.gov (United States)

    Ema, Makoto; Naya, Masato; Yoshida, Kikuo; Nagaosa, Ryuichi

    2010-04-01

    The present paper summarizes data on the reproductive and developmental toxicity of hydrofluorocarbons (HFCs), including pentafluoroethane (HFC-125), 1,1,1,2-tetrafluoroethane (HFC-134a), 1,1,1-trifluoroethane (HFC-143a), 1,1-difluoroethane (HFC-152a), difluoromethane (HFC-32) and 1,1,1,3,3-pentafluoropropane (HFC-245fa), used as refrigerants, published in openly available scientific literature. No developmental toxicity of HFC-125 was found even at 50,000 ppm in rats or rabbits. Although HFC-134a exhibited no dominant lethal effect or reproductive toxicity in rats, it caused low body weight in pre- and postnatal offspring and slightly retarded skeletal ossification in fetuses at 50,000 ppm in rats. No maternal or developmental toxicity was noted after exposure to HFC-143a even at 40,000 ppm in rats or rabbits or HFC-152a even at 50,000 ppm in rats. HFC-32 is slightly maternally and developmentally toxic at 50,000 ppm in rats, but not in rabbits. HFC-245fa caused decreases in maternal body weight and food consumption at 10,000 and 50,000 ppm and fetal weight at 50 000ppm. No evidence of teratogenicity for these HFCs was noted in rats or rabbits. There is limited information about the reproductive toxicity of these HFCs. Animal studies remain necessary for risk assessments of chemicals because it is difficult to find alternative methods to determine the toxic effects of chemicals. It is required to reduce emissions of organic vapors containing HFCs to reduce the risk of exposure. Copyright 2009 Elsevier Inc. All rights reserved.

  17. Diseño de una red WAN

    OpenAIRE

    Labella Sanz, Gabriel

    2010-01-01

    Disseny d'una xarxa WAN, formada per una xarxa d'Accés HFC, una xarxa de Commutació ATM i una xarxa de Transport SDH. Diseño de una red WAN, formada por una red de Acceso HFC, una red de Conmutación ATM y una red de Transporte SDH. WAN network design consisting of a HFC access network, an ATM switching network and a SDH transport network.

  18. Fiscal 1974 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on glass system materials); 1974 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-26

    This report describes the fiscal 1974 research result on glass system materials of plane collectors for solar cooling/heating. A barrel lens type collector was poorer in efficiency than conventional ones. A one-directional Fresnel lens type one was promising for improvement of solar radiation collection. The prototype In{sub 2}O{sub 3} selective transmission cover glass was prepared by vacuum deposition. Although selective characteristics including a solar transmissivity of 74% and an IR reflectance of 75-80% were obtained, further improvement of more than 10% is necessary. The evaluation results of some collectors are as follows. A vacuum type is poor because of its low efficiency and necessary vacuum sealing. A multi-layer type shows unsatisfactory performance at some temperatures. A glass honeycomb type is most likely because of its uppermost collection efficiency, however, development of production technology of heat-resistant honeycombs and its profitability remain to be solved. A deformed multi-layer type is practical because of its high efficiency, simple structure and low cost. Further improvement of the transmissivity and IR reflectance of cover glass by more than 10% is necessary. (NEDO)

  19. Fiscal 1976 Sunshine Project result report. R and D on solar cooling/heating and hot water supply system (R and D on glass system materials); 1976 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report describes the fiscal 1976 research result on solar heat collectors using glass system materials. In fiscal 1976, study was made on improvement of selective transmission films by vacuum deposition and large prototype films, prototype coated glass by chemical treatment and its quality stability, prototype full-scale honeycomb collector, practical heat collection property, and evaluation of some problems. As the study result, characteristics of this selective transmission glass were equivalent to those of the other selective transmission films with a transmissivity of 0.90 and a reflectivity of 0.10. As the study result of production cost by vacuum deposition and resistance heating, the film treatment cost was estimated to be 2,300yen/m{sup 2}. 40 prototype coated glass plates of 1,000 x 1,000 x 3mm, and 300 prototype coated glass pipes of 16mm diameter, 870mm long and 0.6mm thick were prepared for prototype collectors. Two kinds of full-scale collectors prepared by using these selective absorption heat collection plates and coated glass showed favorable performance in heat collection experiment. (NEDO)

  20. FY 1977 Annual report on Sunshine Project results. Research and development of solar energy systems for air conditioning and hot water supply (Research and development of glass-based materials); 1977 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-05-01

    This project is aimed at development of the following collector techniques for various types of solar energy systems for air conditioning and hot water supply: (1) selective transmission glass, (2) reflection-preventive glass, (3) glass-based selective absorption film, and (4) high-performance collector. For the item (1), the STG coated with a reflection-preventive film of In{sub 2}O{sub 3} and that with MgF{sub 2} attain the target performance, and high-speed sputtering is investigated for development of the mass production techniques and promising results are produced. For the item (2), formation of a uniform reflection-preventive film on the glass's front surface and improvement of the reproducibility are investigated, and promising results are produced. For the item (3), a selective absorption plane having a solar radiation absorptivity of 0.90 or more and infrared emissivity of 0.30 or less is produced by baking a SnO{sub 2} film on a soft steel plate undercoated with a black glaze as the glass-based film. For the item (4), a total of 4 types of collectors are fabricated on a trial basis and tested for their heat-collecting performance; a honeycomb type with the selective absorption film, modified laminated type with changed pipe arrangement, one using a large-size reflection-preventive glass, and another one with changed method for supporting the heat-collecting plate. Attainable performance level of the flat plate type collector for commercial purposes is estimated, and the specifications of the commercial collector as the research target are determined. (NEDO)

  1. Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of high pressure fluid aided dyeing and finishing system for cellulose textile products generating no waste liquid; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Cellulose kei sen'i seihin no koatsu ryutai ni yoru muhaieki senshoku kako system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a voice in the textile dyeing industry for a dyeing and finishing method without discharge of waste liquid from the viewpoint of environmental protection. When the special coexistence effect is applied to the technology of making polar dyes soluble in high pressure carbon dioxide, according to Associate Professor Mishima of Fukuoka University, a dyeing method is feasible wherein the separation of supercritical carbon dioxide and the dye is easier than in the conventional method of dyeing in water and wherein discharge of waste liquid after dyeing is not necessary. He also writes that technologies for recovering carbon dioxide have already been established. Under this project, attention is paid to cellulose textile products which will find a great demand, and efforts are made to commercialize a novel dyeing and finishing system of the low environmental impact type. The results of the research conducted under the project involve (1) the improvement of various dyes and assistants in their degree of solution in high pressure carbon dioxide, (2) development of a technology of attaching dyes and finishing agents to textiles, (3) designing and construction of a practical high pressure fluid dyeing and finishing apparatus, (4) search for optimum dyeing conditions for textile products using the said apparatus, and (5) the reinforced functions that textile products have after being dyed. (NEDO)

  2. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  3. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  4. Achievement of 900kgf/cm[sup 2] super workable high strength concrete with belite Portland cement (elevator building of cement silo in Chichibu cement). 2. ; Application to the actual structure. Ko belite kei cement de 900kgf/cm[sup 2] wo tassei (Chichibu cement cement silo no elevator to). 2. ; Jitsukozobutsu eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Yoda, K.; Sakuramoto, F. (Kajima Corp., Tokyo (Japan))

    1993-08-01

    For the purpose of rationalization of concrete works, the super workable high strength concrete was applied to the underground part of elevator building of cement silo in the Kumagaya Works, Chichibu Cement, and was successfully put into practice. Quality control values of the super workable high strength concrete were 65[plus minus]5cm in the slump flow and 900kgf/cm[sup 2] in the compressive strength at the age of 28 days. Addition of the admixture was 1.25% of the unit cement amount. Based on the linear correlation between the slump flow and mixer load immediately before discharge, the slump flow was controlled by the mixer load. Property of the fresh concrete, fluidity, compacting property, material segregation resistance property, and strength property were examined by using a sidewall test model. For all tests, satisfactory properties were obtained. Subsequently, the actual structure was successfully constructed. As a result, laborsaving and improvement of productivity were confirmed for the super workable high strength concrete work. 3 refs., 8 figs., 4 tabs.

  5. FY 2000 report on the project for promotion of clean coal technology. Survey of overseas trends of technology to use hydrocarbon base energy such as coal; 2000 nendo clean coru technology suishin jigjyo. Sekitan tou tankasuiso kei energy riyo gijutsu ni kansuru kaigai doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For contributing to the study on the comprehensive development of technology to use hydrocarbon resource such as coal in Japan, survey was conducted of trends of supply/demand, policy, utilization technology, etc. of hydrocarbon base energy such as coal in developed countries such as the U.S., European countries, etc. Proved coal reserves in the world are 980 billion tons, and years of mining are 230. The resource amount of coal is more than those of oil and natural gas. In the U.S., the budget was largely cut in the 1990s because of the financial deficit, but the R and D are being promoted of power plant being aimed at substantial reduction in emissions of NOx, SOx, etc. and reduction in cost. European countries are tackling the technical development of petroleum substituting energy and the verification/commercialization. As to the clean coal technology, every country is making the technical development for coal liquefaction/gasification. Relating to the natural gas technology, studies are being made of GTL, coal bed methane, shale gas, methane hydrate, etc. The energy conversion use of waste, technical development of biomass energy, etc. were also being carried out. (NEDO)

  6. Achievement report for fiscal 1981 on Sunshine Program research and development. Research and development of amorphous solar cells (Research on amorphous silicon-based new materials); 1981 nendo amorphous taiyo denchi no kenkyu kaihatsu seika hokokusho. Amorphous silicon kei shinzairyo no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In an a-Si{sub 1-x}Ge{sub x}:H film formed by decomposition in a glow discharge, since Ge-H is weaker than Si-H in terms of bonding, an increase in the amount of Ge decreases the amount of H and increases the number of Ge dangling bonds (DBs). Actually, however, H bonded to Si also decreases the number of DBs in Ge. This suggests that H is not working only to terminate DBs but that it also decreases the number of DBs through its structure-softening effect. In the case of a-Si{sub 1-x}C{sub x}:H, an increase in C results in an increase in H and in the number of DBs in both Si and C, this because C-H is stronger than Si-H in terms of bonding. F in a film is quite mobile. SiF and SiH in presence as distributed are found to decrease the number of DBs. Concerning the effect of hydrogen plasma processing for a-Si formed by thermolysis (CVD: chemical vapor deposition), the light transmission rate, absorption, ESR (electro-spin resonance) process time, and dependency on film thickness are investigated, and the relationship is examined between the defect-reducing effect of the H taken into the film and the transmission of light. It is found, as the result of experiments by a simplified molecular orbital method, that DBs stay in existence keeping away from where H or F is in presence. (NEDO)

  7. Properties of P/M forged Al-Si alloys made by premixed powders. 1. Influences of dispersion and sizes of proeutectic Si on wear resistance; Kongoho ni yotte sakuseishita Al-Si kei shoketsu tanzo gokin no tokusei. 1. Taimamosei ni oyobosu shosho Si no bunsan jotai to ryukei no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ishijima, Z.; Ichikawa, J.; Sasaki, s.; Shikata, H. [Hitachi Powdered Metals Co. Ltd., Tokyo (Japan)

    1995-10-15

    Influences of dispersion and sizes of proeutectic Si on wear resistance of P/M Al-Si alloys using the prealloying method and premixing method have been investigated. As a result, discretely dispersed proeutectic Si showed excellent wear resistance in compassion with uniformly dispersed one. The cause is considered to be the unclosed Si soft phase which has been preferentially worn away, consequently acting on forming oil grooves and burying worn particles. Further more the existence of the optimum size of proeutectic Si on wear resistance was confirmed. In the case of finer particles, only Al-Si alloy (pin) was warned away substantially. On the other handgun the case of larger particles, both the Al-Si alloy (pin) and the mating malarial (steel disc) were excessively warned away. It is assumed therefore that the finer proeutectic Si particles are not effective as hard particles, on the contrary, larger proeutectic Si particles increase the abrasive wear against the mating material, and those buried into the mating material initiate wear of Al-Si alloy at the same time. 2 refs., 10 figs., 1 tab.

  8. Fiscal 2000 technology trend survey. Survey of technology trend relating to next-generation metal-based material compatible with inverse manufacturing leading to energy use rationalization; 2000 nendo gijutsu doko chosa hokokusho. Energy shiyo gorika ni kakawaru inverse manufacturing ni tekigoushita jisedai kinzoku kei zairyo ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the construction of a recycling system consuming less energy and therefore higher in efficiency, studies were made about the feasibility of metallic material developing/recycling systems more congruent with the objective through the application of inverse manufacturing (IM). Concerning metallic materials and recycling technologies, steel, aluminum alloys, and magnesium alloys were taken up, and a survey was made of hazardous elements in steel materials, unification of materials to constitute aluminum alloy parts, yield of magnesium in die casting, and the like. In the survey of recycling of automobiles, it was pointed out that the treatment of resin-based shredder dust was posing problems and that the use of metallic materials high in recyclability was essential to IM. In conclusion, three propositions were presented, which involved technologies for the advanced use of magnesium alloys as materials leading to the realization of IM, the development of recycling-oriented general-purpose alloys (with Mg and Al as mother metals), and the development of functional bonding technology enabling debonding (debondable bonding technology). (NEDO)

  9. Research on fabrication technology for thin film solar cells for practical use. Technological development for qualitative improvement (development of fabrication technology of thin film polycrystalline Si solar cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Kohinshitsuka gijutsu (usumaku takessho silicon kei taiyo denchi seizo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on the fabrication technology of thin film polycrystalline Si solar cells in fiscal 1994. (1) On the fabrication technology of high-quality Si thin films, the new equipment was studied which allows uniform stable melting recrystallization over a large area. The new equipment adopted a heating method based on RTP system, and is now under adjustment. (2) On the fabrication technology of light/carrier confinement structure, degradation of hydrogen-treated thin film Si solar cells by light irradiation was examined. As a result, since any characteristic degradation was not found even by long time light irradiation, the high quality of the cells was confirmed regardless of hydrogen-treatment. Fabrication of stable reproducible fine texture structure became possible by using fabrication technology of light confinement structure by texture treatment of cell surfaces. (3) On low-cost process technology, design by VEST process, estimation of cell characteristics by simulation, and characteristics of prototype cells were reported. 33 figs., 1 tab.

  10. Crystallization behavior of Li2O-SiO2, Na2O-SiO2 and Na2O-CaO-SiO2 glasses; Li2O-SiO2, Na2O-SiO2, Na2O-CaO-SiO2 kei glass no kessho sekishutsu kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, K.; Otake, J.; Nagasaka, T.; Hino, M. [Tohoku University, Sendai (Japan)

    1998-06-01

    It has been known that crystallization of mold powder is effective on the disturbance of heat transfer between mold and solidified shell in production of middle carbon steel slabs in continuous casting process. But it has not yet been made clear which composition of mold powder is the most suitable for crystallization. The crystallization behavior of Li2O-SiO2, Na2O-SiO2 and Na2O-CaO-SiO2 glasses was observed by differential thermal analysis (DTA) and hot-thermocouple methods with DTA in the present work. As a result, addition of alkaline metal and alkaline earth metal oxides to SiO2 increased the critical cooling rate for glass formation in binary system of Li2O-SiO2 and Na2O-SiO2 and Li2O-SiO2 system crystallized easier than Na2O-SiO2 system. In ternary system of Na2O-CaO-SiO2, addition of Na2O hurried the critical cooling rate at CaO/SiO2=0.93 mass ratio, but the rate was almost constant in the composition range of more than 15 mass% Na2O. The slag of CaO/SiO2=0.93 made the rate faster than the slag of CaO/SiO2=0.47 at constant content of 10mass% Na2O. 17 refs., 10 figs., 3 tabs.

  11. Reports on 1979 result of Sunshine Project. R and D on solar cooling/heating and hot-water supply system (R and D on glass based materials); 1979 nendo taiyo reidanbo oyobi kyuto system no kenkyu kaihatsu seika hokokusho. Glass kei zairyo no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-05-01

    The purpose of this research is as follows: (1) For a vitreous selective absorbing film; establishment of large-plate processing conditions of a selective absorbing film using a black glass enamel layer, and setting of heat collector plate structure and estimation of its manufacturing cost, (2) For a high-performance collector; establishment of thin film honeycomb forming technology and estimation of its manufacturing cost. In examining the large-plate conditions, a processing test device was made for a vitreous selective absorbing film, a device capable of continuous glass enamel coating and SnO{sub 2} film spraying, which resulted the same {epsilon} characteristics as the two-step processing. Spraying conditions were established for two kinds of sizes of an iron base board. The glass enamel coating was examined using the spraying method, with the flawless result obtained. A tube-on-sheet method was employed as the heat collector plate structure of the vitreous selective absorbing film, obtaining a value of 147kcal/m(center dot)Hr(center dot)degree C. With the vitreous absorbing film processing applied on an iron base board, a heat collector plate of 1x2m was experimentally produced. Using this heat collector plate, a trial product was made for a multiple layer type collector, and the heat collecting efficiency ratio was measured, which was as predicted. The manufacturing cost of one heat collector plate is estimated as 13,000 yen in mass production (1,000 units/month). This research is complete. (NEDO)

  12. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of new composite polymer electrolyte for battery; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Denchiyo shinki fukugo polymer kei denkaishitsu no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of new composite polymer electrolyte for Li secondary battery. The ultimate target of the development using this electrolyte is to get Li secondary battery markedly improved in safety/reliability which works at low temperature and controls thermal runaway. The composite polymer base electrolyte is composed of high molecular weight polyethylene oxide copolymer, ethylene oxide oligomer and Li salt, and it is finally cross-linked by heat or light. Studies were made in the following 6 fields: 1) R and D of the creation and optimization of new composite polymer electrolyte; 2) R and D of the commercialization of composite polymer electrolyte battery; 3) R and D on the safety of composite polymer electrolyte; 4) study of the synthesis of new electrolyte and catalytic activity of electrolyte-electrode interface; 5) R and D on polymer/oligomer composite electrolyte; and 6) comprehensive investigational research. (NEDO)

  13. FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the commercialization of cogeneration using ligneous biomass in Kochi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kochi ken mokushitsu kei baiomasu riyo netsuden heikyu jigyoka kanosei chosa itaku gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/study were conducted of potentiality of the cogeneration business using ligneous biomass in Kami County and the periphery of Kochi Prefecture. In the survey, the following were studied: regional characteristics of the said area, levels of technology of direct combustion/thermochemical conversion, future technical trends, system candidate, grasp/analysis of the resource amount, characteristics of ligneous biomass resource in the said area, analysis of economical efficiency of the procurement of biomass resource, grasp of energy users, etc. As a result, a system was selected of a 1,000kW scale cogeneration of ligneous resource. At the present technology level and under scale conditions, it was found out that the fixed bed direct combustion system was the most profitable in securing the economical realization. As to the system mostly for power generation, however, it was found out that the heat low in unit price of energy production should widely be used because the installation cost of plant is comparatively high. Facilities such as Kochi Medical Center where heat is in great demand throughout the year can expect profit from selling heat, and therefore, those have high potentiality of the commercialization. (NEDO)

  14. 78 FR 12310 - Inventory of U.S. Greenhouse Gas Emissions and Sinks: 1990-2011

    Science.gov (United States)

    2013-02-22

    ... dioxide (CO 2 ), methane (CH 4 ), nitrous oxide (N 2 O), hydrofluorocarbons (HFC), perfluorocarbons (PFC..., petrochemical production, phosphoric acid, titanium dioxide, lime production, and several fluorinated gas...

  15. A study on the impact of the quality of management education on the new economy-knowledge: Evidence from members of OIC countries

    Directory of Open Access Journals (Sweden)

    Maryam Yokhaneh

    2014-08-01

    Full Text Available This paper studies the effects of Quality of Management Education (QME at universities on knowledge creation, application and distribution in knowledge based economy(KEI. The study also investigates the influence of QME on effective use of knowledge in economic development(KI.Using some regression technique, the study has determined a positive relationship of the effects of QME on KEI and KI in members of organization of Islamic cooperation (OIC. In addition, the study investigates the position of Iran in terms of quality of management education and the level of knowledge based economy.

  16. Vocational education teachers’ attitude towards development of assessment skills

    OpenAIRE

    Miliušienė, Monika; Teresevičienė, Margarita

    2009-01-01

    Šiame straipsnyje aptariamas mokymosi pasiekimų vertinimo procesas, daugiausia dėmesio skiriama profesijos mokytojų gebėjimų vertinti nustatymui. Keičiantis vertinimo koncepcijai, t. y. pereinant nuo vien tik žiniomis paremto vertinimo prie mokymosi pasiekimų vertinimo, keičiasi vertinimo eigai keliami reikalavimai ir ypač aktualus tampa profesijos mokytojų gebėjimų vertinti tobulinimas. This article discusses learning achievement assessment process, focusing on identification of VET teach...

  17. Analysis of semantic search within the domains of uncertainty: using Keyword Effectiveness Indexing as an evaluation tool.

    Science.gov (United States)

    Lorence, Daniel; Abraham, Joanna

    2006-01-01

    Medical and health-related searches pose a special case of risk when using the web as an information resource. Uninsured consumers, lacking access to a trained provider, will often rely on information from the internet for self-diagnosis and treatment. In areas where treatments are uncertain or controversial, most consumers lack the knowledge to make an informed decision. This exploratory technology assessment examines the use of Keyword Effectiveness Indexing (KEI) analysis as a potential tool for profiling information search and keyword retrieval patterns. Results demonstrate that the KEI methodology can be useful in identifying e-health search patterns, but is limited by semantic or text-based web environments.

  18. Kohtuvad tummfilmid ja elektrooniline muusika / Kirsi Lattu

    Index Scriptorium Estoniae

    Lattu, Kirsi

    2011-01-01

    Festivali "Tummfilmid tõstavad häält" raames linastub Vene Kultuurikeskuses 4. märtsil film "Antenn" (režissöör Esteban Sapir, Argentina, 2007), millele loob muusikat Argento Tango Fusion Hispaaniast, 5. märtsil film "Tabu" (režissöör Friedrich Wilhelm Murnau, USA, 1931), millele loob muusikat Konono No 1 Kongo DV-st

  19. Gesture and Power

    OpenAIRE

    Covington-Ward, Yolanda

    2016-01-01

    In Gesture and Power Yolanda Covington-Ward examines the everyday embodied practices and performances of the BisiKongo people of the lower Congo to show how their gestures, dances, and spirituality are critical in mobilizing social and political action. Conceiving of the body as the center of analysis, a catalyst for social action, and as a conduit for the social construction of reality, Covington-Ward focuses on specific flashpoints in the last ninety years of Congo's troubled history, when ...

  20. EU-Verordnung zu "Konfliktmineralien": Ein Schritt zu höherer Rechenschaftspflicht im Rohstoffsektor?

    OpenAIRE

    Küblböck, Karin; Grohs, Hannes

    2017-01-01

    "No blood in my cell phone" - Anfang der 2000er-Jahre zeigten Kampagnen von Nichtregierungsorganisationen (NGOs) Verbindungen zwischen Rohstoffen in Elektronikprodukten und der Finanzierung des Krieges in der Demokratischen Republik Kongo (DRC) auf. In diesem Zusammenhang rückte auch die Verantwortung von Unternehmen für die Gestaltung ihrer Lieferkette verstärkt ins öffentliche Bewusstsein. 2017 tritt nun eine EU-Verordnung in Kraft, die verhindern soll, dass Unternehmen durch ihre Rohstoffb...

  1. Requirements for a Device-Based Training and Testing Program for M1 Gunnery. Volume 2. Detailed Analyses and Results

    Science.gov (United States)

    1988-03-01

    ACTIVITY 11. ASSESS RESULTS OF ENCAGENENT TC GNU IDR M Alien battle dauge/c<iua1ttis Check/adJuit MRS Dtttratiw If and how crm ihould bt... UfO Of ring« lino con fco obiorvod on CRT. Kongo It not innounctd, but oppaor on CRT diti oroo. U(0 of ringt lint con bo obior»td on CRT

  2. Field evaluation of spatial repellency of metofluthrin-impregnated plastic strips against Anopheles gambiae complex in Bagamoyo, coastal Tanzania.

    OpenAIRE

    Kawada, Hitoshi; Temu, Emmanuel A.; Minjas, Japhet N.; Matsumoto, Osamu; Iwasaki, Tomonori; Takagi, Masahiro

    2008-01-01

    Metofluthrin is a newly synthesized pyrethroid possessing high knockdown and lethal activity against mosquitoes. Studies of metofluthrin-impregnated plastic strips have been performed with dengue vectors. This study reports the efficacy of the new prototypes of metofluthrin-impregnated plastic strips against malaria vectors, Anopheles gambiae complex, in the Kongo villages of Bagamoyo district in coastal Tanzania. The study, using 20 houses, half intervention, half control, was conducted for ...

  3. Design and methodology of the NorthStar Study

    DEFF Research Database (Denmark)

    Schou, Morten; Gustafsson, Finn; Videbaek, Lars

    2008-01-01

    Randomized clinical trials have shown that newly discharged and symptomatic patients with chronic heart failure (CHF) benefit from follow-up in a specialized heart failure clinic (HFC). Clinical stable and educated patients are usually discharged from the HFC when on optimal therapy. It is unknown...

  4. Analysis of South Carolina hydrogen and fuel cell workers views and opinion leadership behavior: A waiting opportunity?

    Energy Technology Data Exchange (ETDEWEB)

    Besley, John C. [School of Journalism and Mass Communications, University of South Carolina, Columbia, SC 29205 (United States); Baxter-Clemmons, Shannon [South Carolina Hydrogen Fuel Cell Alliance, P.O. Box 12302, Columbia, SC 29201 (United States)

    2010-08-15

    The current study uses quantitative survey results to explore what a near census of hydrogen and fuel cell (HFC) workers in South Carolina (n = 70) say about their HFC experiences and the degree to which these workers can be expected to act as opinion leaders for the field. In general, these workers say they are positive about the environmental, national security, and economic potential of HFC technologies. They further see HFC technologies as having small and manageable levels of risk. A number of these workers exhibit characteristics associated with both issue-specific and general opinion leadership. Issue-specific leadership and positive views about HFC technology were associated with higher levels of self-reported technology-related interpersonal discussion. The study concludes that the existence of workers with positive HFC experiences and a demonstrated interest in telling others about their experiences may represent an opportunity for those charged with promoting HFC development and adoption. Future efforts should explore how HFC workers could be effectively integrated into such efforts as a means of reaching difficult to reach audiences. (author)

  5. Rate Constants for the Reactions of OH with CH(sub 3)Cl, CH(sub 2) C1(sub 2), CHC1(sub 3)and CH(sub 3)Br

    Science.gov (United States)

    Hsu, H-J.; DeMore, W.

    1994-01-01

    Rate constants for the reactions of OH with CH3C1, CH2Cl2, CHCl3 and CH3Br have been measured by a relative rate technique in which the reaction rate of each compound was compared to that of HFC-152a (CH3CHF2)and for CH2Cl2, HFC-161 (CH3CH2F).

  6. High temperature strengthening mechanism of hafnium carbide in a tungsten-rhenium matrix

    International Nuclear Information System (INIS)

    Luo, A.; Shin, K.S.; Jacobson, D.L.

    1991-01-01

    The interrelationship between the testing temperature and HfC strength increment of an arc-melted W-3.6Re-0.4HfC was determined from 1950 K to 2980 K in a vacuum of better than 1.3x10 -5 Pa (10 -7 torr). The present research was focused on the characteristic temperature at which the rapid coarsening of HfC particles occurred and the effect of the second-phase particle size on the high temperature strength properties of this material. It was found that the HfC particle strengthening was effective in a W-Re matrix up to a characteristic temperature of 2450 K in the short-term tensile test. Carbon was found to be the rate-limiting solute in the HfC particle growth. The strength of HfC strengthened alloy at temperature above 0.5 T m is proportional to the square root of particle volume fraction. The yield strengths of W-3.6Re-0.26HfC calculated based on the particle statistical distribution had good agreement with the experimental values from 1950 K to 2980 K. Besides, an addition of 0.26 percent HfC in tungsten resulted in about 28 percent increase in the activation energy of plastic deformation at high temperatures

  7. 40 CFR Appendix E to Subpart B of... - The Standard for Automotive Refrigerant Recycling Equipment Intended for Use With Both CFC-12 and...

    Science.gov (United States)

    2010-07-01

    ... Refrigerant Recycling Equipment Intended for Use With Both CFC-12 and HFC-134a E Appendix E to Subpart B of... Appendix E to Subpart B of Part 82—The Standard for Automotive Refrigerant Recycling Equipment Intended for... Intended for Use With Both CFC-12 and HFC-134a Foreword The purpose of this standard is to establish...

  8. Cryoinsulation Material Development to Mitigate Obsolescence Risk for Global Warming Potential Foams

    Science.gov (United States)

    Protz, Alison; Bruyns, Roland; Nettles, Mindy

    2015-01-01

    Cryoinsulation foams currently being qualified for the Space Launch System (SLS) core stage are nonozone- depleting substances (ODP) and are compliant with current environmental regulations. However, these materials contain the blowing agent HFC-245fa, a hydrofluorocarbon (HFC), which is a Global Warming Potential (GWP) substance. In August 2014, the Environmental Protection Agency (EPA) proposed a policy change to reduce or eliminate certain HFCs, including HFC-245fa, in end-use categories including foam blowing agents beginning in 2017. The policy proposes a limited exception to allow continued use of HFC and HFC-blend foam blowing agents for military or space- and aeronautics-related applications, including rigid polyurethane spray foams, but only until 2022.

  9. Animated Dreamsi festivali parimad said eile auhinnad / Kaarel Kressa

    Index Scriptorium Estoniae

    Kressa, Kaarel, 1983-

    2010-01-01

    12. animafilmide festivali Animated Dreams grand prix' pälvis Kei Oyama film "Käeseep" (Jaapan, 2008). Parima disaini preemia sai Jonas Odelli "Tussilago" (Rootsi, 2010). Parima loo jutustas Olga ja Priit Pärna "Tuukrid vihmas" (Eesti, 2009). Teistest preemiatest

  10. Fish abundance and distribution in the Gamtoos estuary with notes ...

    African Journals Online (AJOL)

    favourably with other larger systems like the Sundays, Bashee and Kei estuaries. .... as well as the use of pesticides undoubtedly affects water quality in the ... Methods. Catch per unit effort (CPUE) of fish in the Gamtoos estuary was obtained ...

  11. The eye-catching cicada Hamza ciliaris (Linnaeus, 1758) comb. n. in Indonesia and the Pacific: taxonomie status, synonymy, and distribution (Homoptera, Cicadoidea)

    NARCIS (Netherlands)

    Duffels, J.P.

    1991-01-01

    The new combination Hamza ciliaris (Linnaeus) is proposed for a cicada species widely distributed in Maluku ( = Moluccas), Timor, Banda, Kei and Banggai Islands, the Philippines, and the Palau group of the Caroline Islands. The synonymy of five species, treated in the literature as junior synonyms

  12. Arhitektuuriuudised / Karen Jagodin

    Index Scriptorium Estoniae

    Jagodin, Karen, 1982-

    2006-01-01

    Mario Garzaniti korrusmaja Brüsselis, Ryue Nishizawa kortermaja Tokyos, Hamburgi arhitektuuribüroo Blauraum loomingust, Michael P. Johnsoni eramu Phoenixis, jaapani arhitekti Kei'ichi Irie ja Power Unit Studio loodud monoliitbetoonist eramu Chita linnas, hollandi arhitektuuribüroo OMA loomingust, inglise büroo Peter Barber Architects lahendus Londoni ühe eeslinna kvartalile

  13. Strategic field No.5 'the origin of matter and the universe'. Toward interdisciplinary researches in particle, nuclear and astrophysics

    International Nuclear Information System (INIS)

    Aoki, Shinya

    2011-01-01

    Four main research subjects in the strategic field No. 5 'The origin of matter and the universe', planned to be investigated on 'Kei' super computer, are explained in detail, by focusing on interdisciplinary aspect of researches among particle, nuclear and astrophysics. (author)

  14. National Competitiveness in Global Economy: Evolution of Approaches and Methods of Assessment

    Directory of Open Access Journals (Sweden)

    - Teng Delux

    2011-09-01

    Full Text Available The basic concept of national competitiveness and the analytic potential model for the estimation of countries' competitiveness, such as diamond model of competitive advantages of national economies by M. Porter, the generalized double diamond model of international competitiveness by C. Moon, 9-factors model by S. Cho, Global Competitiveness Index (GCI and Knowledge Economy Index (KEI are considered.

  15. Annual Risk of Tuberculosis Infection in the Transkei

    African Journals Online (AJOL)

    1974-05-11

    May 11, 1974 ... kei by the State Health Service, SANTA, and the Tuber- culosis Research ... method. The annual risk of tuberculous infection was calculated to be approximately 7%. A downward trend of only 2% per year was seen. S. Afr. Med. J., 48, 957 ... A random survey of the population of the Transkei was undertaken ...

  16. A DESCRIPTION OF BUFO PARDALIS TADPOLES (ANURA ...

    African Journals Online (AJOL)

    Tadpoles of Bufo parda/is Hewitt from Kei Road, Cape Province, are described. INTRODUCTION. Although tadpoles of B. pardalis have been included in Van Dijk's (1971) key to the genus Bufa, no adequate description of this taxon has yet been published. Further studies on variability depend upon a complete description ...

  17. A preliminary fish survey of the estuaries on the southeast coast of ...

    African Journals Online (AJOL)

    2016-01-01

    Jan 1, 2016 ... ABSTRACT. A basic ichthyofaunal and physico-chemical survey of estuaries on the southeast coast of South Africa from Kayser's Beach to Kei Mouth was undertaken during September and October 1996. Twenty-eight (28) estuaries have been identified along this stretch of coastline, and these were ...

  18. Modelo en laboratorio de las reacciones de degradación de los CFC'S, HCFC'S y HFC'S en la atmósfera : su relación con la degradación de la capa de ozono y el efecto invernadero

    OpenAIRE

    Vázquez Dols, José Luis

    2011-01-01

    La concentración de ozono en la estratosfera es producto de un balance de fuerzas creadoras y destructivas. El nivel de ozono en la estratosfera debe mantenerse constante, actuando en régimen permanente. En la estratosfera la concentración de ozono varía ligeramente reflejando ligeras variaciones sobre el punto de equilibrio entre la formación y la destrucción. Estas fluctuaciones son debidas a procesos naturales tales como: ciclos estacionales, erupciones volcánicas, cambios en la intensidad...

  19. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  20. Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a high-calorie gas manufacturing technology (research on a pressurized and fluidized gasification system for coal and heavy oil mixed materials); Sekitan gas ka gijutsu no kenkyu kaihatsu seika hokokusho. Kokarori gas seizo gijutsu no kaihatsu (sekitan oyobi jushitsuyu kongo genryo no kaatsu ryudo gas ka hoshiki no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    This paper describes the achievements in developing a high-calorie gas manufacturing technology for coal gasification in the Sunshine Project in fiscal 1981. Pulverized coal and heavy oil are heated and stirred to make it a slurry, which is forced into a fluidized bed gasification furnace together with spraying steam, and pyrolyzed by using a unique slurry feeding system (a hydrohoist). Carbon-like material as a by-product (char) is partially oxidized (burned) by steam and oxygen at the lower part of the gasification furnace. The material is gasified in the furnace, where the generated heat is sent to the pyrolysis zone in the upper part by the gas and fluidized bed media particles (char), and utilized as a heat source for the slurry pyrolysis. The produced gas is cooled by an indirect heat exchanger of the fluidized bed system and a scrubber to separate tar, dust and unreacted steam. Part of the sensible heat is recovered as steam. Thus, high-calorie gas of 6,000 kcal/Nm{sup 3} can be obtained, which is rich in methane, CO and hydrogen. Fiscal 1981 has performed a continuous test by using an internal heat type low-pressure gasification equipment to evaluate its compatibility to the diversification of materials. (NEDO)

  1. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  2. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  3. Performance analysis of the electric vehicle air conditioner by replacing hydrocarbon refrigerant

    Science.gov (United States)

    Santoso, Budi; Tjahjana, D. D. D. P.

    2017-01-01

    The thermal comfort in passenger cabins needs an automotive air-conditioning system. The electric vehicle air conditioner system is driven by an electric compressor which includes a compressor and an electric motor. Almost air-conditioning system uses CFC-12, CFC-22 and HFC-134a as refrigerant. However, CFC-12 and CFC-22 will damage the ozone layer. The extreme huge global warming potentials (GWP) values of CFC-12, CFC-22, and HFC-134a represent the serious greenhouse effect of Earth. This article shows new experimental measurements and analysis by using a mixture of HC-134 to replace HFC-134a. The result is a refrigerating effect, the coefficient of performance and energy factor increase along with cooling capacity, both for HFC-134a and HC-134. The refrigerating effect of HC-134 is almost twice higher than HFC-134a. The coefficient of performance value of HC-134 is also 36.42% greater than HFC-134a. Then, the energy factor value of HC-134 is 3.78% greater than HFC-134a.

  4. Report on a survey in fiscal 1999 for trends in policies on prevention of global warming by use of substitute fluorocarbons; 1999 nendo daitai furon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper summarizes mainly on HFC, PFC and SF{sub 6} the trends in the last one year in technologies and regulations that can make compatible the ozone layer protection and the global warming prevention. Activities of the HFC/PHC task force established jointly by TEAP and IPCC are very important in deciding the future positions of HFC, PFC and SF{sub 6}. This paper reports the status of activities taken during fiscal 1999. IPCC reviewed the method of calculating the quantity of greenhouse effect gas emission. The paper introduces from its draft the gist of calculating the discharge quantity of HFC, PFC and SF{sub 6}. Introduction is given from the HFC/PFC task force report the actual status of using coolants, foaming agents and aerosols using HFC, PFC and SF{sub 6}, and the trends of developing substitution technologies. The paper introduces a fluorocarbon destruction technology as an international trend in discharge suppression measures. The paper reports movements of COP-5 in fiscal 1999 for gases other than the three gases including HFC. Chlorobromo-methane was indicated as a new substance, and n-propyl-bromide was decided to continue with measurement of ozone destruction coefficient. (NEDO)

  5. Sync-measurement experimental study of (fluoroethane + dimethylether tetraethylene glycol), (fluoroethane + dimethylether triethylene glycol) and (fluoroethane + dimethylether diethylene glycol) systems

    International Nuclear Information System (INIS)

    Feng, Lejun; Zheng, Danxing; Huang, Weijia

    2016-01-01

    Highlights: • Three new working pairs are proposed for absorption power cycle. • Sync-measured the solubility and absorption enthalpy data at 303.15 K. • Thermokinetic experiment is consistent with the previous thermodynamics study. - Abstract: In this work, three new working pairs, {fluoroethane (HFC161) + dimethylether tetraethylene glycol (DMETEG)}, {HFC161 + dimethylether triethylene glycol (DMETrEG)} and {HFC161 + dimethylether diethylene glycol (DMEDEG)}, are proposed for absorption power cycle. The working pairs are assessed from both thermodynamics and thermokinetic perspective. By combining the microcalorimetry and isothermal synthesis methods, an experimental apparatus was developed to simultaneously obtain the microcalorimetry and vapour–liquid equilibrium data. Then, the solubility and absorption enthalpy data of the three new working pairs were sync-measured at 303.15 K by this sync-measurement experimental apparatus. The thermodynamics data indicated that the affinities of the three working pairs increased from strong to weak in the following order: HFC161 + DMETEG > HFC161 + DMETrEG > HFC161 + DMEDEG. Then the thermokinetic parameters of the absorption rate constant and activation energy were analysed based on the thermokinetic experiment at (303.15, 313.15, 323.15, and 333.15) K. As a result, the affinities of the three working pairs are consistent with the previous thermodynamics study. In addition, the intermolecular interactions within the three systems were analysed according to the intermolecular hydrogen bonds; overall, the (HFC161 + DMETEG) system is considered to be the potential option for applications.

  6. FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Feasibility survey of the commercialization of the gasification melting system use heat supply business using container packing waste plastic and other waste as raw materials; 2001 nendo kankyo chowa gata energy komyuniti jigyo. Gaska yoyu system wo mochiita yoki hoso kei hai purasuchikku oyobi sonota no haikibutsu wo genryo to suru netsu kyokyu jigyo no jigyoka F/S chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    As to gasification melting facilities (Eco-Ene center) using container packing waste plastic and other waste as raw materials in 'the Eco-town Kochi City - Business Project,' study/evaluation of environmental conservation and business profitability were conducted. In Eco-Ene Center, power generation (power supply to users: 1,295 kW) and heat supply (27 GJ/h at maximum) are conducted using the gas product obtained from the combustion of waste. The environmental effect of introduction of Eco-Ene Center is as follows: energy conservation: 51,350-113,594 GJ/y, environmental pollution gas reduction: 1,128-4,987 t-CO2, 1,441-6,691 kg-NOx, 2,965-6,447 kg-SOx, 27,309 {mu}g-TEQ/m{sup 3} dioxin. As a result of the study of economical efficiency, the following was found out: In securing the ending cash balance such as personnel expenses, land lease cost and transportation cost, the subject is the acceptance price of container packing plastic from which a half of the profit can get, and it is necessary to receive subsidy for 1/2 of the price and reduce operating expenses. (NEDO)

  7. Achievement of 900kgf/cm[sup 2] super workable high strength concrete with belite portland cement. (elevator building of cement silo in Chichibu cement). Part 1. ; Development of cement for super workable high strength concrete. Ko belite kei cement de 900kgf/cm[sup 2] wo tassei (Chichibu cement cement sairo no elevaor to). 1. ; Koryudo kokyodo concrete yo no cement no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, M.; Fukaya, Y.; Nawa, T. (Chichibu Cement Co. Ltd., Tokyo (Japan))

    1993-08-01

    This paper describes the features of high belite Portland cement which can make the super workable high strength concrete, and the properties of concrete using this. The super workable concrete is required an excellent segregation resistance property as well as high flow property. Since the high belite Portland cement contains a small amount of C[sub 3]S in the clinker, the amounts of C[sub 3]A and C[sub 4]AF can be reduced without hindering the calcination of clinker. Additionally, since it contains a large amount of C[sub 2]S with low heat of hydration, an increase in the temperature of members can be suppressed. 'Chichibu High Flow Cement' having characteristics of this high belite Portland cement was developed for the super workable high strength concrete. The concrete using the High Flow Cement exhibited the maximum flow value of 70cm. It also exhibited the strength of 1,075 kgf/cm[sup 2] at the age of 91 days, and 1,100 kgf/cm[sup 2] at the age of 14 days under insulating. 4 refs., 8 figs., 2 tabs.

  8. Fiscal 1998 New Sunshine Program achievement report. Development for practical application of photovoltaic system - Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of high-quality amorphous material/substrate manufacturing technology); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A microcrystalline Si thin film is used to form the i-layer of a narrow gap a-Si based thin film solar cell. Since a microcrystalline p-layer is to act as the seeding crystal layer for the microcrystalline i-layer, it has to be very high in crystallinity and therefore is produced under high hydrogen dilution conditions. In this process, a problem arises of the darkening of the underlying transparent SnO{sub 2} electrode. Since this is due to chemical reaction on the SnO{sub 2} surface layer, blackening is prevented by shortening the film fabrication time, and then an excellently microcrystalline p-layer is obtained. Furthermore, by inserting a microcrystalline i-film buffer layer of low fabrication rate into the p/i boundary, plasma damage on the microcrystalline p-layer is inhibited for the fabrication of a microcrystalline i-layer high in crystallinity at high film fabrication rates. A high Voc is then obtained even when the microcrystalline p-layer is very thin. If the hydrogen dilution rate is too low when the i-layer film fabrication rate is high, the initially fabricated layer turns out to be thick to the detriment of film performance. On the other hand, the p-layer or the buffer layer will be etched when the hydrogen dilution rate is too high. The problem is solved by continuously varying the hydrogen dilution rate from high to low during i-layer fabrication. (NEDO)

  9. Fiscal 1999 research and development of technologies for practical application of photovoltaic power generation systems. Development of thin-film solar cell manufacturing technology (Development of material/substrate manufacturing technology - Development of amorphous silicon-based high-quality material/substrate manufacturing technology); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (zairyo kiban seizo gijutsu kaihatsu - amorphous silicon kei kohinshitsu zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The project aims to enhance the stability of amorphous solar cells. For elevating TCO (transparent conductive oxide) substrate transmittance to an ultrahigh level and for obtaining amorphous layers less to suffer photodegradation, efforts were made to develop substrate materials stable upon exposure to plasma and low in defect density. In the study of TCO, a high-transmittance glass substrate was employed and TCO was made thinner, and the specimen achieved transmittance of 91.3% or 6.3% over that of the conventional type. In the study of low reflection films, it was found that their transmittance came to be stable and remain so after 150 days after a weatherproof test. In the study for stability enhancement, optimization was carried out for a plasma resisting Ga{sub 2}O{sub 3}-added ZnO film for the manufacture of a substrate material capable of properly behaving in a high-speed a-Si film fabrication process. Low-temperature film fabrication was studied to enable low-cost manufacturing, and it was learned that a 4 times 10{sup -4} ohm/cm low-resistance film was obtained by sputtering Ga{sub 2}O{sub 3}-added ZnO where magnetism was intensive at room temperature, that films excellent in crystallinity were obtained by the same method even at low temperatures, and so forth. (NEDO)

  10. FY 1999 research and development of technologies for commercialization of photovoltaic power generation systems. Development of technologies for fabrication of thin-film solar cells/materials and substrates (Development of technologies for fabrication of high-quality amorphous materials and substrates); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu / zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development project is implemented for the amorphous/microcrystalline solar cells with the thin microcrystalline silicon film as the i layer, and the FY 1999 results are reported. The fabrication technologies are investigated for the microcrystalline silicon solar cells of pin or nip structure by RF or VHF plasma CVD using SiH{sub 4} and H{sub 2} as the stock gases. The tests are conducted for evaluating characteristics of the thin microcrystalline silicon film, to investigate the effects of film-making pressure, power and hydrogen dilution rate on the characteristics at a constant film-making temperature of 180 degrees C. The researches on the fabrication technologies for the microcrystalline solar cell of pin structure confirm that use of VHF plasma CVD improves crystallinity, electrical and optical characteristics of the p-type thin microcrystalline silicon film. The researches on the fabrication technologies for the microcrystalline solar cell of nip structure covers transparent substrates, film-making speed of the p layer, power and substrates, and a conversion efficiency of 7.5% is realized by the solar cell formed on a texture substrate. (NEDO)

  11. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

  12. Improvement of sensitizatiuon in weld metals of austenitic stainless steels by laser surface melting treatment. Report 3. Study on low temperature sensitization in weldments of austenitic stainless steels ans its improvement by laser surface melting treatment; Reza hyomen yoyu shori ni yoru sutenresu ko yosetsu kinzoku no enbinka kaizen. 3. Osutenaito kei sutenresu ko yosetsubu no teion enbinka to reza hyomen yoyu shori ni yoru sono kaizen

    Energy Technology Data Exchange (ETDEWEB)

    Nishimoto, K. [Osaka Univ., Osaka (Japan). Faculty of Engineering; Mori, H. [Osaka Univ., Osaka (Japan). Graduate School; Yamamura, T. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

    1997-05-05

    Laser surface melting treatment used for the improvement of intergranular corrosion resistance of sensitized austenitic stainless steel weld metal was studied. As a result, it was revealed that as compared to untreated material, sensitization was improved widely and intergranular corrosion resistance was improved to a level of base metal when laser surface melting treatment of sensitized weld metal was carried out. Further, sensitization effect at a condition of laser traveling velocity of 0.00167m/s was slightly insufficient compared to that of laser traveling velocity above 0.00833m/s. This phenomena was caused due to the existence of {delta} ferrite that accelerates the precipitation of Cr carbides inside the laser treatment portion and together with this, the Cr carbides are precipitated in {delta}/{gamma} grain boundary due to the effect of laser heat cycle with insufficient cooling velocity and this has caused desensitization. 16 refs., 13 figs., 3 tabs.

  13. Synthesis and characterization of hafnium carbide microcrystal chains with a carbon-rich shell via CVD

    International Nuclear Information System (INIS)

    Tian, Song; Li, Hejun; Zhang, Yulei; Liu, Sen; Fu, Yangxi; Li, Yixian; Qiang, Xinfa

    2013-01-01

    Graphical abstract: Novel HfC microcrystal chains have been synthesized via a catalyst-assisted chemical vapor deposition process. SEM results show the chains have a periodically changing diameter and a nanoscale sharpening tip. Analysis of TEM/SAED/EELS/EDX data shows the single-crystal chains grow along a [0 0 1] direction and consist of a HfC core and a thin carbon-rich shell with embedded HfC nanocrystallites surrounding the core. This work achieves the controllable preparation of nanoscale HfC sharpening tips for application as a point electron emission source and facilitates the application of HfC ultrafast laser-triggered tips in attosecond science. Highlights: •HfC microcrystal chains were synthesized by a catalyst-assisted CVD. •The chains grow along a [0 0 1] direction and have a periodically changing diameter. •Single-crystal HfC core is sheathed by a thin carbon-rich shell. •A growth mechanism model is proposed to explain the growth of microcrystal chians. •This work achieves the controllable preparation of nanoscale HfC sharpening tips. -- Abstract: Novel hafnium carbide (HfC) microcrystal chains, with a periodically changing diameter and a nanoscale sharpening tip at the chain end, have been synthesized via a catalyst-assisted chemical vapor deposition (CVD) process. The as-synthesized chains with many octahedral microcrystals have diameters of between several hundreds of nm and 6 μm and lengths of ∼500 μm. TEM diffraction studies show that the chains are single-crystalline HfC and preferentially grow along a [0 0 1] crystal orientation. TEM/EELS/EDX analysis proves the chains are composed of a HfC core and a thin (several tens of nm to 100 nm) carbon-rich shell with the embedded HfC nanocrystallites (typically below 10 nm) surrounding the core. The growth mechanism model for the chains based on the vapor–liquid–solid process, the vapor–solid process, and the HfC crystal growth characteristics is discussed

  14. Extended heart failure clinic follow-up in low-risk patients

    DEFF Research Database (Denmark)

    Schou, Morten; Gustafsson, Finn; Videbaek, Lars

    2013-01-01

    BackgroundOutpatient follow-up in specialized heart failure clinics (HFCs) is recommended by current guidelines and implemented in most European countries, but the optimal duration of HFC programmes has not been established. Nor is it known whether all or only high-risk patients, e.g. identified...... by NT-proBNP, might benefit from an extended HFC follow-up.Methods and resultsIn a multi-centre setting, we randomly assigned 921 clinically stable systolic heart failure (HF) outpatients on optimal medical therapy to undergo either an extended follow-up in the HFC (n = 461) or referral back...

  15. Overview of hybrid fiber-coaxial network deployment in the deregulated UK environment

    Science.gov (United States)

    Cox, Alan L.

    1995-11-01

    Cable operators in the U.K. enjoy unprecedented license to construct networks and operate cable TV and telecommunications services within their franchise areas. In general, operators have built hybrid-fiber-coax (HFC) networks for cable TV in parallel with fiber-copper-pair networks for telephony. The commonly used network architectures are reviewed, together with their present and future capacities. Despite this dual-technology approach, there is considerable interest in the integration of telephony services onto the HFC network and the development of new interactive services for which HFC may be more suitable than copper pairs. Certain technological and commercial developments may have considerable significance for HFC networks and their operators. These include the digitalization of TV distribution and the rising demand for high-rate digital access lines. Possible scenarios are discussed.

  16. The Effects of Water Spray Cooling in Conjunction with Halogenated Extinguishants on Hydrogen Fluoride Generation and Decay

    National Research Council Canada - National Science Library

    Burch, Ian

    2007-01-01

    The halogenated extinguishants Halon 1301, HFC-227ea (FM200) and NAF-S-III used within Royal Australian Navy vessels for total flooding fire suppression applications have hydrogen fluoride (HF) toxicity concerns...

  17. Linking Halal Food Certification and Business Performance

    DEFF Research Database (Denmark)

    Ab Talib, Mohamed Syazwan; Chin, Thoo Ai; Fischer, Johan

    2017-01-01

    , operational performance mediates the relationship between HFC and financial performance. Altogether, this signifies that Halal food certificate implementation positively influences business performance. Practical implications By linking HFC and business performance, managers may be aware of the significant......Purpose The purpose of this paper is to explore the relationship between Halal food certification (HFC) and business performance. This study argues that Halal food certificate implementation positively influences business performance. Design/methodology/approach A total of 210 Halal certified food...... role of HFC in influencing operational and financial performance. It would entice more food companies to become Halal certified that opens up an opportunity to a lucrative Halal food industry. It also empirically justifies that a religion-based food certification has the ability to influence business...

  18. Transitioning to Low-GWP Alternatives in Motor Vehicle Air Conditioning Systems

    Science.gov (United States)

    This fact sheet provides information on low-GWP alternatives in newly manufactured motor vehicle air conditioning systems. It discusses HFC alternatives, market trends, challenges to market entry for alternatives, and potential solutions.

  19. 75 FR 57669 - Mandatory Reporting of Greenhouse Gases

    Science.gov (United States)

    2010-09-22

    ... Mandatory Reporting of Greenhouse Gases AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: This action amends the Final Mandatory Reporting of Greenhouse Gases Rule to require reporters... Numbers GHG greenhouse gas GHGRP Greenhouse Gas Reporting Program HCFC hydrochlorofluorocarbon HFC...

  20. 40 CFR Appendix D to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

    Science.gov (United States)

    2010-07-01

    ... the following criteria, derived from Society of Automotive Engineers (SAE) standards and recommended... Substitutes] Application Substitute Decision Conditions Comments Electronics Cleaning w/CFC-113 and MCF HFC... Sector [Acceptable Subject to Narrowed Use Limits] Application Substitute Decision Comments Electronics...

  1. Rate Constant and Temperature Dependence for the Reaction of Hydroxyl Radicals with 2-Flouropropane (FC-281ea) and Comparison with an Estimated Rate Constant

    Science.gov (United States)

    DeMore, W.; Wilson, E., Jr.

    1998-01-01

    Relative rate experiments were used to measure the rate constant and temperature dependence of the reaction of OH radicals with 2-fluoropropane (HFC-281ea), using ethane, propane, ethyl chloride as reference standards.

  2. Linking Halal Food Certification and Business Performance

    DEFF Research Database (Denmark)

    Ab Talib, Mohamed Syazwan; Chin, Thoo Ai; Fischer, Johan

    2017-01-01

    role of HFC in influencing operational and financial performance. It would entice more food companies to become Halal certified that opens up an opportunity to a lucrative Halal food industry. It also empirically justifies that a religion-based food certification has the ability to influence business...... manufacturing companies in Malaysia participated in the study. Data were gathered through a structured questionnaire and were analysed using partial least squares structural equation modelling technique. Findings The study proved that HFC has a positive relationship with operational performance. Additionally......, operational performance mediates the relationship between HFC and financial performance. Altogether, this signifies that Halal food certificate implementation positively influences business performance. Practical implications By linking HFC and business performance, managers may be aware of the significant...

  3. Improvement of the Material's Mechanical Characteristics using ...

    African Journals Online (AJOL)

    pc

    2018-03-05

    Mar 5, 2018 ... to Hardening Process Control (HPC) in order to improvement of the material's ... particular circumstances of the models characteristics used and the exact definition ..... In the case of simulation and testing in Matlab of the HFC.

  4. Effects of dietary fermentation concentrate of Hericium caput-medusae (Bull.:Fr.) Pers. on growth performance, digestibility, and intestinal microbiology and morphology in broiler chickens.

    Science.gov (United States)

    Shang, Hong Mei; Song, Hui; Xing, Ya Li; Niu, Shu Li; Ding, Guo Dong; Jiang, Yun Yao; Liang, Feng

    2016-01-15

    The present study was undertaken to investigate the effects of fermentation concentrate of Hericium caput-medusae (Bull.:Fr.) Pers. (HFC) on growth performance, digestibility, intestinal microbiology, and intestinal morphology in broiler chickens. A total of 600 male Arbor Acres broilers were randomly divided into five dietary treatments (20 broilers per pen with six pens per treatment): CON (basal diet), ANT (basal diet supplemented with 5 mg kg(-1) flavomycin) and HFC (basal diet supplemented with 6, 12, and 18 g kg(-1) HFC). The experimental lasted for 42 days. The results revealed that the average daily gain [linear (L), P < 0.01; quadratic (Q), P < 0.01] of broilers increased when the HFC levels increased during the starter (days 1-21), finisher (days 22-42), and the overall experiment period (days 1 to 42). In the small intestinal digesta and the caecum digesta, the Escherichia coli count (L, P < 0.05; Q, P < 0.001) decreased while the Lactobacilli count (L, P < 0.01; Q, P < 0.001) and Bifidobacteria count (L, P < 0.001; Q, P < 0.001) increased when the HFC levels increased. The crude protein digestibility of broilers (L, P < 0.01; Q, P < 0.001) increased when the HFC levels increased. In the duodenum, jejunum, and ileum of broilers, the villus height and villus height to crypt depth ratio (L, P < 0.001; Q, P < 0.001) increased when the HFC levels increased. Dietary supplementation with HFC increased gut Lactobacilli and Bifidobacteria counts and inhibited E. coli growth, improved nutrient utilisation and intestine villus structure, and thus improved the growth of broilers. © 2015 Society of Chemical Industry.

  5. FY 1998 annual summary report on recent trends of global warming prevention measures with fluorochlorohydrocarbon alternatives; 1998 nendo daitia furon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the recent trends of the ozone layer protection and global warming prevention measures. Latest international information has been collected by attending the 10th Meeting of the Party of Montreal Protocol, and the 17th and 18th Open Ended Working Group. The important decisions made so far are investigation on the novel ozone layer destruction substances, requirement of studying on decommissioning Halon facilities, collection of information of HFC and PFC, and reporting to IPCC. Information regarding regulation trends of HFC, PFC and SF{sub 6} are collected by attending the COP-4 meeting and the preparatory meetings therefor. The report on these 3 substances will be completed in July or so, 1999. The trends of technical development in HCFC alternatives in refrigeration and blowing sectors were investigated. HFC-245fa and HFC-365mfc are introduced. Also introduced is latest information regarding the emission estimation and control measures of HFC in USA and UK, emission control measures of SF{sub 6} in USA and Japan, and techniques for destruction of CFC and the like, which could be the basic techniques for controlling diffusion of HFC. The CFC phase-out programs of China, the biggest ozone layer destruction substance (e.g., CFC) consuming country, are also outlined. (NEDO)

  6. Cooling performance of R510A in domestic water purifiers

    International Nuclear Information System (INIS)

    Park, Ki Jung; Lee, Yo Han; Jung, Dong Soo

    2010-01-01

    Cooling performance of R510A is examined both numerically and experimentally in an effort to replace HFC134a in the refrigeration system of domestic water purifiers. Although the use of HFC134a is currently dominant, it is being phased out in Europe and most developed countries due to its high potential contribution to global warming. To solve this problem, cycle simulation and experimental measurements are conducted with a new refrigerant mixture of 88%RE170/12%R600a using actual domestic water purifiers. This mixture has been recently numbered and listed as R510A by ASHRAE. Test results show that, due to the small internal volume of the refrigeration system of the domestic water purifiers, system performance with R510A is greatly influenced by the amount of charge. With the optimum charge amount of 20 to 21 g, approximately 50% that of HFC134a, the energy consumption of R510A is 22.3% lower than that of HFC134a. The compressor discharge temperature of R510A is 3.7 .deg. C lower than that of HFC134a at the optimum charge. Overall, R510A, a new, long term, and environmentally safe refrigerant, is a good alternative for HFC134a. Furthermore, it requires only minor changes in the refrigeration system of the domestic water purifiers

  7. Libert-E Motor

    Science.gov (United States)

    Sieloff, Susan F.; Kinnunen, Raymond; Chevarley, Joseph

    2011-01-01

    Kei Yun Wong has big dreams. She has been entrusted with the United States launch of Libert-E Motor, a new line of Chinese-manufactured electric scooters. With only $750,000 of her original budget of $3 million left, she needs to make sure that the launch succeeds, as it represents the initial step in her desire to create the first Chinese global…

  8. A new Cyrtanthus species(Amaryllidaceae: Cyrtantheae endemic to the Albany Centre, Eastern Cape, South Africa

    Directory of Open Access Journals (Sweden)

    D. A. Snijman

    2003-09-01

    Full Text Available Cyrtanthus macmasteri Snijman is a rare new species from the Albany Centre of endemism. Eastern Cape. South Africa. Most closely related to C.  galpinii Baker, and autumn-flowering species with a single or rarely-flowered inflorescence from the northern regions of southern Africa. C macmasteri is distinguished by a 3 to 6-flowered inflorescence. It grows on steep banks of the Great Kei River and its tributaries and flowers in summer.

  9. A Pseudomonas aeruginosa strain isolated from a contact lens-induced acute red eye (CLARE) is protease-deficient.

    Science.gov (United States)

    Estrellas, P S; Alionte, L G; Hobden, J A

    2000-03-01

    Pseudomonas aeruginosa proteases are thought to be important virulence factors in the pathogenesis of corneal disease. This study examined protease production from two strains of P. aeruginosa responsible for two very distinct clinical diseases: strain Paer1, isolated from a Contact Lens-induced Acute Red Eye (CLARE), and strain KEI 1025, isolated from a corneal ulcer. Strains were compared to a laboratory strain (ATCC 19660) known to produce severe keratitis in experimentally infected mice for protease production and for ocular virulence. Protease production was examined with colorimetric assays, gelatin zymography and western blots. Elastase A activity was quantitated with a staphylolytic assay. Ocular virulence was examined using a mouse scratch model of keratitis. In contrast to strains KEI 1025 or ATCC 19660, Paer1 was unable to produce enzymatically active elastase A, elastase, and protease IV. All three strains produced active alkaline protease. Strains KEI 1025 and ATCC 19660 produced a fulminant keratitis in mice whereas Paer1 produced a mild transient infection. Restoration of elastase activity in Paer1 via genetic complementation did not result in a virulent phenotype. Co-infection of mouse eyes with strains Paer1 and ATCC 19660 resulted in the eventual loss of Paer1 from corneal tissue. These studies suggest that P. aeruginosa elastase A and/or protease IV, but not alkaline protease or elastase, contribute to the ocular virulence of this organism.

  10. Aqueous-stream uranium-removal technology cost/benefit and market analysis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The primary purpose of this report is to present information that was gathered by Kapline Enterprises, Inc. (KEI) in order to help the Department of Energy (DOE) determine the merit of continued biosorption research funding. However, in the event that funding is continued, it is also intended to help the researchers in their efforts to develop a better uranium-removal process. This report (1) provides a comparison of DOE sites that may utilize aqueous-stream, uranium-removal biosorption technology, (2) presents a comparison of the biosorption and ion exchange processes, and (3) establishes performance criteria by which the project can be measured. It also attempts to provide focus for biosorbent ground-water-remediation research and to ask questions that need to be answered. This report is primarily a study of the US market for technologies that remove uranium from aqueous streams, but it also addresses the international market-particularly for Germany. Because KEI`s access to international market information is extremely limited, the material presented in this report represents a best effort to obtain this data. Although uranium-contaminated aqueous streams are a problem in other countries as well, the scope of this report is primarily limited to the US and Germany for two reasons: (1) Germany is the country of the biosorbent-CRADA partner and (2) time constraints.

  11. Strategic research field no.4, industrial innovations

    International Nuclear Information System (INIS)

    Kato, Chisachi

    2011-01-01

    'Kei'-supercomputer is planned to start its full-scale operation in about one year and a half. With this, High Performance Computing (HPC) is most likely to contribute not only to further progress in basic and applied sciences, but also to bringing about innovations in various fields of industries. It is expected to substantially shorten design time, drastically improve performance and/or liability of various industrial products, and greatly enhance safety of large-scale power plants. In this particle, six research themes, which are currently being prepared in this strategic research field, 'industrial innovations' so as to use 'Kei'-supercomputer as soon as it starts operations, will be briefly described regarding their specific goals and break-through that they are expected to bring about in industries. It is also explained how we have determined these themes. We are also planning several measures in order to promote widespread use of HPC including 'Kei'-supercomputer in industries, which will also be elaborated in this article. (author)

  12. Aqueous humor from traumatized eyes triggers cell division in the epithelia of cultured lenses

    International Nuclear Information System (INIS)

    Reddan, J.R.; Weinsieder, A.; Wilson, D.

    1979-01-01

    Experiments were designed to gain a better understanding of the relationship between ocular inflammation and cell proliferation in the lens epithelium. Aqueous humor (AH) was collected from rabbit eyes that had been subjected to a variety of traumata, including paracentesis, needle injury, X-irradiation and the intravitreal administration of an antigen. In all cases the protein content of the AH increased, reflecting a breakdown in the blood aqueous barrier. Rabbit lenses from non-traumatized eyes were isolated and cultured in medium KEI-4 containing samples of the various aqueous humors noted above. Control lenses were cultured in medium KEI-4 alone or in KEI-4 containing rabbit serum albumen at a protein concentration equivalent to that used in the AH studies. In contrast to controls, the epithelial cells of lenses exposed to AH from injured or inflamed eyes exhibited mitosis throughout the normally amitotic regions of epithelium. Moreover, the specific activity of AH collected 15 min after initial paracentesis, relative to both DNA synthesis and mitosis, exceeded that of rabbit serum. An identification of the mitogenic factor(s) in the AH may help in understanding the environmental conditions that regulate the mitotic response which normally precedes wound healing in the lens in situ, and may help in elucidating the mechanism which controls mitosis and differentiation in the lens in vivo. (author)

  13. Increase Economic Valuation of Marine Ecotourism Spots In Small Islands

    Science.gov (United States)

    Rahakbauw, Siska D.; Teniwut, Wellem A.; Renjaan, Meiskyana R.; Hungan, Marselus

    2017-10-01

    Ecotourism is one of the fast-growing sectors especially in the developing country as a source of revenue. To get a sustainable development of ecotourism, it needs broad and comprehensive effort from central government and local government, perfect example in that regards in Indonesia is Bali and Lombok. For another area in Indonesia like Kei Islands which located in two administrative governments have a major problem to build a sustainable nature-based tourism because of the location of this area to the major cities in the country makes the travel cost is high. This situation makes the role of local community as the backbone of the growth and development of nature-based tourism is critical. By using structural equation modeling (SEM), we constructed a model to enhance local community perception on economic valuation of ecotourism spots in the area. Results showed that perceived quality as the mediation driven by the intensity of appearance on national television and the internet could increase community attachment to increase willingness to pay from the local community on ecotourism in Kei islands. Also, the result also indicated that WTP value for the local community on ecotourism in Kei Islands was 10.81 per trip, with average trip per month was 1 to 4 times.

  14. Abundance and sources of atmospheric halocarbons in the Eastern Mediterranean

    Science.gov (United States)

    Schoenenberger, Fabian; Henne, Stephan; Hill, Matthias; Vollmer, Martin K.; Kouvarakis, Giorgos; Mihalopoulos, Nikolaos; O'Doherty, Simon; Maione, Michela; Emmenegger, Lukas; Peter, Thomas; Reimann, Stefan

    2018-03-01

    A wide range of anthropogenic halocarbons is released to the atmosphere, contributing to stratospheric ozone depletion and global warming. Using measurements of atmospheric abundances for the estimation of halocarbon emissions on the global and regional scale has become an important top-down tool for emission validation in the recent past, but many populated and developing areas of the world are only poorly covered by the existing atmospheric halocarbon measurement network. Here we present 6 months of continuous halocarbon observations from Finokalia on the island of Crete in the Eastern Mediterranean. The gases measured are the hydrofluorocarbons (HFCs), HFC-134a (CH2FCF3), HFC-125 (CHF2CF3), HFC-152a (CH3CHF2) and HFC-143a (CH3CF3) and the hydrochlorofluorocarbons (HCFCs), HCFC-22 (CHClF2) and HCFC-142b (CH3CClF2). The Eastern Mediterranean is home to 250 million inhabitants, consisting of a number of developed and developing countries, for which different emission regulations exist under the Kyoto and Montreal protocols. Regional emissions of halocarbons were estimated with Lagrangian atmospheric transport simulations and a Bayesian inverse modeling system, using measurements at Finokalia in conjunction with those from Advanced Global Atmospheric Gases Experiment (AGAGE) sites at Mace Head (Ireland), Jungfraujoch (Switzerland) and Monte Cimone (Italy). Measured peak mole fractions at Finokalia showed generally smaller amplitudes for HFCs than at the European AGAGE sites except for periodic peaks of HFC-152a, indicating strong upwind sources. Higher peak mole fractions were observed for HCFCs, suggesting continued emissions from nearby developing regions such as Egypt and the Middle East. For 2013, the Eastern Mediterranean inverse emission estimates for the four analyzed HFCs and the two HCFCs were 13.9 (11.3-19.3) and 9.5 (6.8-15.1) Tg CO2eq yr-1, respectively. These emissions contributed 16.8 % (13.6-23.3 %) and 53.2 % (38.1-84.2 %) to the total inversion

  15. Health facility committees and facility management - exploring the nature and depth of their roles in Coast Province, Kenya

    Directory of Open Access Journals (Sweden)

    Kabare Margaret

    2011-09-01

    Full Text Available Abstract Background Community participation has been emphasized internationally as a way of enhancing accountability, as well as a means to enhance health goals in terms of coverage, access and effective utilization. In rural health facilities in Kenya, initiatives to increase community accountability have focused on Health Facility Committees (HFCs. In Coast Province the role of HFCs has been expanded with the introduction of direct funding of rural facilities. We explored the nature and depth of managerial engagement of HFCs at the facility level in two rural districts in this Coastal setting, and how this has contributed to community accountability Methods We conducted structured interviews with the health worker in-charge and with patients in 30 health centres and dispensaries. These data were supplemented with in-depth interviews with district managers, and with health workers and HFC members in 12 health centres and dispensaries. In-depth interviews with health workers and HFC members included a participatory exercise to stimulate discussion of the nature and depth of their roles in facility management. Results HFCs were generally functioning well and played an important role in facility operations. The breadth and depth of engagement had reportedly increased after the introduction of direct funding of health facilities which allowed HFCs to manage their own budgets. Although relations with facility staff were generally good, some mistrust was expressed between HFC members and health workers, and between HFC members and the broader community, partially reflecting a lack of clarity in HFC roles. Moreover, over half of exit interviewees were not aware of the HFC's existence. Women and less well-educated respondents were particularly unlikely to know about the HFC. Conclusions There is potential for HFCs to play an active and important role in health facility management, particularly where they have control over some facility level resources

  16. Health facility committees and facility management - exploring the nature and depth of their roles in Coast Province, Kenya.

    Science.gov (United States)

    Goodman, Catherine; Opwora, Antony; Kabare, Margaret; Molyneux, Sassy

    2011-09-22

    Community participation has been emphasized internationally as a way of enhancing accountability, as well as a means to enhance health goals in terms of coverage, access and effective utilization. In rural health facilities in Kenya, initiatives to increase community accountability have focused on Health Facility Committees (HFCs). In Coast Province the role of HFCs has been expanded with the introduction of direct funding of rural facilities. We explored the nature and depth of managerial engagement of HFCs at the facility level in two rural districts in this Coastal setting, and how this has contributed to community accountability We conducted structured interviews with the health worker in-charge and with patients in 30 health centres and dispensaries. These data were supplemented with in-depth interviews with district managers, and with health workers and HFC members in 12 health centres and dispensaries. In-depth interviews with health workers and HFC members included a participatory exercise to stimulate discussion of the nature and depth of their roles in facility management. HFCs were generally functioning well and played an important role in facility operations. The breadth and depth of engagement had reportedly increased after the introduction of direct funding of health facilities which allowed HFCs to manage their own budgets. Although relations with facility staff were generally good, some mistrust was expressed between HFC members and health workers, and between HFC members and the broader community, partially reflecting a lack of clarity in HFC roles. Moreover, over half of exit interviewees were not aware of the HFC's existence. Women and less well-educated respondents were particularly unlikely to know about the HFC. There is potential for HFCs to play an active and important role in health facility management, particularly where they have control over some facility level resources. However, to optimise their contribution, efforts are needed to

  17. Pushing Back the Origin of Bantu Lexicography: The Vocabularium Congense of 1652, 1928, 2012

    Science.gov (United States)

    De Kind, Jasper; de Schryver, Gilles-Maurice; Bostoen, Koen

    2013-01-01

    In this article, the oldest Bantu dictionary hitherto known is explored, that is the Vocabularium Latinum, Hispanicum, e Congense, handed down to us through a manuscript from 1652 by the Flemish Capuchin Joris van Gheel, missionary in the Kongo (present-day north-western Angola and the southern part of the Lower Congo Province of the DRC). The manuscript was heavily reworked by the Belgian Jesuits Joseph van Wing and Constant Penders, and published in 1928. Both works are currently being digitized, linked and added to an interlingual and multimedia database that revolves around Kikongo and the early history of the Kongo kingdom. In Sections 1 and 2 the origins of Bantu lexicography in general and of Kikongo metalexicography in particular are revisited. Sections 3 and 4 are devoted to a study of Van Gheel’s manuscript and an analysis of Van Wing and Penders’ rework. In Sections 5 and 6 translation equivalence and lexicographical structure in both dictionaries are scrutinized and compared. In Section 7, finally, all the material is brought together. PMID:23814547

  18. Pushing Back the Origin of Bantu Lexicography: The Vocabularium Congense of 1652, 1928, 2012.

    Science.gov (United States)

    De Kind, Jasper; de Schryver, Gilles-Maurice; Bostoen, Koen

    2012-12-01

    In this article, the oldest Bantu dictionary hitherto known is explored, that is the Vocabularium Latinum, Hispanicum, e Congense , handed down to us through a manuscript from 1652 by the Flemish Capuchin Joris van Gheel, missionary in the Kongo (present-day north-western Angola and the southern part of the Lower Congo Province of the DRC). The manuscript was heavily reworked by the Belgian Jesuits Joseph van Wing and Constant Penders, and published in 1928. Both works are currently being digitized, linked and added to an interlingual and multimedia database that revolves around Kikongo and the early history of the Kongo kingdom. In Sections 1 and 2 the origins of Bantu lexicography in general and of Kikongo metalexicography in particular are revisited. Sections 3 and 4 are devoted to a study of Van Gheel's manuscript and an analysis of Van Wing and Penders' rework. In Sections 5 and 6 translation equivalence and lexicographical structure in both dictionaries are scrutinized and compared. In Section 7, finally, all the material is brought together.

  19. Severe symptoms of short tear break-up time dry eye are associated with accommodative microfluctuations

    Directory of Open Access Journals (Sweden)

    Kaido M

    2017-05-01

    Full Text Available Minako Kaido,1,2 Motoko Kawashima,1 Reiko Ishida,1,3 Kazuo Tsubota1 1Department of Ophthalmology, Keio University School of Medicine, Tokyo, 2Wada Eye Clinic, Chiba, 3Ishida Eye Clinic, Shizuoka, Japan Aim: Validating the hypothesis that accommodative microfluctuations (AMFs may be associated with severe symptoms in short tear break-up time (BUT dry eye (DE. Methods: This study included 12 subjects with short BUT DE (age: 49.6±18.3 years. Diagnoses were performed based on the presence of DE symptoms, BUT ≤5 s, Schirmer score >5 mm, and negative keratoconjunctival epithelial damage. Tear evaluation, AMF, and functional visual acuity (VA examinations were conducted before and after DE treatment. The AMF parameters evaluated were: total high-frequency component (HFC, HFC with low accommodation for the task of staring into the distance (HFC1, HFC with high accommodation for deskwork (HFC2. A subjective questionnaire of DE symptoms was also performed. Results: Mean BUT increased from 1.9±2.0 to 6.4±2.5 s after treatment (P<0.05. The mean logarithm of the minimum angle of resolution functional VA significantly improved (from 0.19±0.19 to 0.12±0.17; P<0.05. Mean power spectrum values for total HFC and HFC1 decreased (from 61.3±5.7 to 53.8±6.6 dB and from 62.9±10.5 to 52.4±6.2 dB, respectively; P<0.05, while the mean HFC2 power spectrum values did not differ before and after treatment (P>0.05. Subjective DE symptoms were reduced in nine patients. Conclusion: Along with the improvement of BUT after treatment, DE symptoms diminished and HFC1 and functional VA improved, suggesting that tear film instability is associated with deterioration of functional VA, AMF, and DE symptoms. Keywords: accommodative microfluctuation, ciliary muscle spasm, dry eye, ocular fatigue, tear break-up time, functional visual acuity 

  20. FY 2000 Report on the results of survey on recent situations of global warming mitigation measures related to alternative fluorochlorohydrocarbons; 2000 nendo daitai furon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The recent situations of global warming mitigation measures related to flurine-containing greenhouse gases of HFC, PFC and SF{sub 6} are surveyed. In the meeting of the Parties of Montreal Protocol of 2000, no decision has been made on HCFC phaseout schedule amendment in the developed and developing countries, which is one of the major items. COP-6 has failed to reach agreement on handling CO2 absorption sources. For the international trends in estimation of the emissions of HFC and others, the IPCC's emission estimation methodology guidance for HFC, PFC and SF{sub 6} (translated into Japanese) and the methodologies taken by other countries are introduced. The trends of the emission control measures for HFC, PFC and SF{sub 6} include CO2 refrigerant application for mobile air-conditioners, announcement by Coca-Cola of HFC phaseout by 2004, announcement by the Canadian refrigerant air-conditioner industry of introduction of the surcharge system for promoting refrigerant recovery, and SF{sub 6} emission reduction technologies in Mg fabricating industries. Also introduced are cost evaluation of emission reduction technologies, latest scientific knowledge in the global environments, and harmonization of global warming mitigation and ozone layer protection in the developing countries, among others. (NEDO)

  1. Recycling of tailings from Korea Molybdenum Corporation as admixture for high-fluidity concrete.

    Science.gov (United States)

    Jung, Moon Young; Choi, Yun Wang; Jeong, Jae Gwon

    2011-01-01

    The main objective of this study is to develop an eco-friendly and a large recycling technique of flotation Tailings from korea (TK) from metal mines as construction materials such as admixtures for high-fluidity concrete (HFC). TK used in this study was obtained from the Korea Molybdenum Corporation in operation. TK was used as the alternative material to adjust flowability and viscosity of HFC in the form of powder agent which enables adjustment of concrete compressive strength. In this study, we have performed concrete rheological tests and concrete flowability tests to obtain the quality characteristics of TK for using as the admixture in producing HFC. The results indicated that the adequate mix ratio of cement to TK should be 8:2 (vol%). It is more effective to use the TK as admixture to control flowability, viscosity and strength of HFC than the normal concrete. It was found that TK could be recycled construction materials in bulk such as admixture for HFC, in terms of the economic and eco-friendly aspects.

  2. Frequencies of inaudible high-frequency sounds differentially affect brain activity: positive and negative hypersonic effects.

    Directory of Open Access Journals (Sweden)

    Ariko Fukushima

    Full Text Available The hypersonic effect is a phenomenon in which sounds containing significant quantities of non-stationary high-frequency components (HFCs above the human audible range (max. 20 kHz activate the midbrain and diencephalon and evoke various physiological, psychological and behavioral responses. Yet important issues remain unverified, especially the relationship existing between the frequency of HFCs and the emergence of the hypersonic effect. In this study, to investigate the relationship between the hypersonic effect and HFC frequencies, we divided an HFC (above 16 kHz of recorded gamelan music into 12 band components and applied them to subjects along with an audible component (below 16 kHz to observe changes in the alpha2 frequency component (10-13 Hz of spontaneous EEGs measured from centro-parieto-occipital regions (Alpha-2 EEG, which we previously reported as an index of the hypersonic effect. Our results showed reciprocal directional changes in Alpha-2 EEGs depending on the frequency of the HFCs presented with audible low-frequency component (LFC. When an HFC above approximately 32 kHz was applied, Alpha-2 EEG increased significantly compared to when only audible sound was applied (positive hypersonic effect, while, when an HFC below approximately 32 kHz was applied, the Alpha-2 EEG decreased (negative hypersonic effect. These findings suggest that the emergence of the hypersonic effect depends on the frequencies of inaudible HFC.

  3. Frequencies of inaudible high-frequency sounds differentially affect brain activity: positive and negative hypersonic effects.

    Science.gov (United States)

    Fukushima, Ariko; Yagi, Reiko; Kawai, Norie; Honda, Manabu; Nishina, Emi; Oohashi, Tsutomu

    2014-01-01

    The hypersonic effect is a phenomenon in which sounds containing significant quantities of non-stationary high-frequency components (HFCs) above the human audible range (max. 20 kHz) activate the midbrain and diencephalon and evoke various physiological, psychological and behavioral responses. Yet important issues remain unverified, especially the relationship existing between the frequency of HFCs and the emergence of the hypersonic effect. In this study, to investigate the relationship between the hypersonic effect and HFC frequencies, we divided an HFC (above 16 kHz) of recorded gamelan music into 12 band components and applied them to subjects along with an audible component (below 16 kHz) to observe changes in the alpha2 frequency component (10-13 Hz) of spontaneous EEGs measured from centro-parieto-occipital regions (Alpha-2 EEG), which we previously reported as an index of the hypersonic effect. Our results showed reciprocal directional changes in Alpha-2 EEGs depending on the frequency of the HFCs presented with audible low-frequency component (LFC). When an HFC above approximately 32 kHz was applied, Alpha-2 EEG increased significantly compared to when only audible sound was applied (positive hypersonic effect), while, when an HFC below approximately 32 kHz was applied, the Alpha-2 EEG decreased (negative hypersonic effect). These findings suggest that the emergence of the hypersonic effect depends on the frequencies of inaudible HFC.

  4. Cyber Security in Digital I and C Implementation

    Energy Technology Data Exchange (ETDEWEB)

    Chow, Ivan; Hsu, Allen; Kim, Jong Min; Luo, William [Doosan HF Controls, Texas (United States)

    2011-08-15

    During the Nuclear Regulatory Commission (NRC) audit process of Doosan HF Control HFC-6000 safety system 2009, cyber security assessment was a major audit process. The result of the assessment was favorably satisfied. As preventing digital I and C systems from being hijacked by malicious software a major goal for the NRC, audit process of actual digital I and C implementations such as the HFC-6000 safety system which provides already strong cyber security measures is mutually beneficial to both the NRC and the vendor: NRC can enhance their set of cyber security assessments and vendors such as Doosan HFC can also augment their cyber security measures. The NRC Safety Evaluation Report (SER) for the HFC-6000 system was released in April 2011 qualifying the system to be used as safety systems in US nuclear power plants. This paper provides the summary of the cyber security assessment of the complete software life cycle of HFC-6000 Safety System. Lessons learned in each life cycle phase are provided. In addition, alternate measures or recommendations for enhancing the cyber security in each life cycle phase are also described.

  5. Cyber Security in Digital I and C Implementation

    International Nuclear Information System (INIS)

    Chow, Ivan; Hsu, Allen; Kim, Jong Min; Luo, William

    2011-01-01

    During the Nuclear Regulatory Commission (NRC) audit process of Doosan HF Control HFC-6000 safety system 2009, cyber security assessment was a major audit process. The result of the assessment was favorably satisfied. As preventing digital I and C systems from being hijacked by malicious software a major goal for the NRC, audit process of actual digital I and C implementations such as the HFC-6000 safety system which provides already strong cyber security measures is mutually beneficial to both the NRC and the vendor: NRC can enhance their set of cyber security assessments and vendors such as Doosan HFC can also augment their cyber security measures. The NRC Safety Evaluation Report (SER) for the HFC-6000 system was released in April 2011 qualifying the system to be used as safety systems in US nuclear power plants. This paper provides the summary of the cyber security assessment of the complete software life cycle of HFC-6000 Safety System. Lessons learned in each life cycle phase are provided. In addition, alternate measures or recommendations for enhancing the cyber security in each life cycle phase are also described

  6. A study of creep behavior in refractory alloys for thermionic emitter applications

    International Nuclear Information System (INIS)

    Gao Hong; Zee, Ralph

    1997-01-01

    The creep behavior of HfC strengthened tungsten alloys was studied. An ultrahigh vacuum high precision creep test system was constructed for this purpose so that the samples could be heated up to 3000 K for heat treatment and creep strain could be measured from the creep sample inside the vacuum chamber. Creep tests were conducted in tungsten strengthened with 0.37 percent of HfC at temperatures between 2000 K to 2500 K for durations up to 8 weeks. To explain the creep behavior observed in this dispersion strengthened alloy, a creep model was proposed which accounted for the presence of HfC particles in the form of a back stress generated by these particles. This model was verified by the creep test data of a W-0.37HfC alloy tested under both extruded and recrystallized microstructural conditions. According to this model, the steady state creep of this type alloys was expected to increase with time due to the HfC particle coarsening and recrystallization under high temperatures. In contrast, conventional simple power law creep only predicts a constant steady state creep for these materials, which does not represent the microstructural evolution of the materials. In this study, the experimental study was designed to verify the semi-mechanistic phenomenological creep model developed for carbide particle strengthened tungsten alloys

  7. National technical report (Matsushita Electric Industrial Company), Vol. 41, No. 3, June 1995. Special issue on environmental technologies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    ;Contents: Preface to Special Issue on Environmental Technologies; Total System for Recycling and Optimal Treatment of Waste Home Electric Appliances; Material Reduction Design Using Computer Aided Engineering; Rewritable Thermal Recording Sheet; Reusable Taping System; Estimating Method for Disassembly of Home Appliances; Thermal Design Technique to Reduce Furnace Running Cost to Half; Study of Air Conditioner Using HFC Refrigerant Blend; High-Efficiency Compact Rotary Compressor Using New Refrigerant HFC 134a for Automotive Air Conditioner; Simulation for Refrigerators Using HFC 134a; Zero-ODP (Ozone Depletion Potential) Rigid Insulation Foams for Refrigerators; Heat Energy of Industrial Waste Combustion Gas Utilization System; Exhaust Gas Denitrification System for Car Road Tunnels and Underground Parking Areas; Apparatus for Regenerating Diesel Particulate Filter Using Microwave; Analysis of Advanced Treatment System of Heavy Metals in Waste Water; Ventilating and Air-Conditioning System for Energy-Saving Houses; Garbage Disposer; and Anti-Microbial Resin and Applications to Products in Harmony with Living Environment.

  8. Comparison of a R744 cascade refrigeration system with R404A and R22 conventional systems for supermarkets

    International Nuclear Information System (INIS)

    Silva, Alessandro da; Pedone Bandarra Filho, Enio; Pontes Antunes, Arthur Heleno

    2012-01-01

    The present article focuses on the energy efficiency and climate performance of three different systems used in supermarket applications. The refrigeration systems consist of a cascade cycle (CO 2 /HFC-404A) – provide nominal refrigerating capacity – with carbon dioxide for subcritical operation and HFC-404A in the high stage temperature stage (pump circuit for normal refrigeration and direct expansion for deep-freezing), and also HFC-404A and HCFC-22 with direct expansion systems. The cascade system presented a lower refrigerant charge, 47 kg of both fluids, which represents less than a half of the refrigerant charge of the other systems. An important factor is the total GWP in case of leakage, where the impact in the atmosphere of the cascade system operating with CO 2 was much less than the two direct expansion systems.

  9. Measurement of some biophysical parameters in skin lesions of leprosy

    Directory of Open Access Journals (Sweden)

    A B Gupta

    1990-01-01

    Full Text Available Transepidermal water loss (TEWL, high frequency electrical conductance (HFC and the hydration state index (HSI were measured in sldn lesions of 30 paucibacillary leprosy patients and compared with the contralateral uninvolved skin. While the TEWL, HFC and HSI all showed lower values in the lesion site, as compared to the contralateral skin sites, the differences between the two sets of values significant in HFC and. HSI only at 2% and 1% level respectively. A significant positive correlation (r = 0.69 was found to eidst between these two parameters. The parameters correlate well with the known reduced sweating in skin lesions of TT and BT leprosy and may therefore be considered as good objective parameters to confirm hypohydrosis in suspected skin lesions ofleprosy.

  10. A density functional study of EPR hyperfine coupling of vanadocene(IV) complexes

    International Nuclear Information System (INIS)

    Honzicek, Jan; Vinklarek, Jaromir; Nachtigall, Petr

    2004-01-01

    Suitability of various exchange-correlation functionals for calculations of HFC tensors was investigated. It was found that A iso calculated with B3PW91 functional correlates fairly well with experimental A iso for broad range of vanadocene compounds. Simple scaling of calculated A iso was proposed. A good correspondence between experimental HFC tensors and those calculated at DFT optimised geometries was found. It is shown that structure of vanadocene complex can be assigned based on the comparison of experimental and theoretical HFC tensors and several examples are presented. The exchange functionals with large mixing of exact exchange (BHPB86) give A iso with an error that depends on the extent of spin-contamination of the wavefunction

  11. Hiperlipidemia familiar combinada: documento de consenso

    Directory of Open Access Journals (Sweden)

    Pedro Mata

    2014-10-01

    Es frecuente la asociación con diabetes mellitus tipo 2, hipertensión arterial y obesidad central. Los pacientes con HFC se consideran de riesgo cardiovascular alto y el objetivo terapéutico es un colesterol-LDL < 100 mg/dl, y < 70 mg/dl en presencia de enfermedad cardiovascular establecida o diabetes mellitus. Los pacientes con HFC requieren tratamiento con estatinas potentes y, a veces, tratamiento combinado. La identificación y el manejo de otros factores de riesgo cardiovascular, como la diabetes y la hipertensión, son fundamentales para reducir la carga de enfermedad cardiovascular. Este documento proporciona recomendaciones para el diagnóstico y el tratamiento integral de los pacientes con HFC especialmente dirigidas a médicos de atención primaria.

  12. Inflammatory Signals shift from adipose to liver during high fat feeding and influence the development of steatohepatitis in mice

    Directory of Open Access Journals (Sweden)

    Greenfeder Scott

    2011-03-01

    Full Text Available Abstract Background Obesity and inflammation are highly integrated processes in the pathogenesis of insulin resistance, diabetes, dyslipidemia, and non-alcoholic fatty liver disease. Molecular mechanisms underlying inflammatory events during high fat diet-induced obesity are poorly defined in mouse models of obesity. This work investigated gene activation signals integral to the temporal development of obesity. Methods Gene expression analysis in multiple organs from obese mice was done with Taqman Low Density Array (TLDA using a panel of 92 genes representing cell markers, cytokines, chemokines, metabolic, and activation genes. Mice were monitored for systemic changes characteristic of the disease, including hyperinsulinemia, body weight, and liver enzymes. Liver steatosis and fibrosis as well as cellular infiltrates in liver and adipose tissues were analyzed by histology and immunohistochemistry. Results Obese C57BL/6 mice were fed with high fat and cholesterol diet (HFC for 6, 16 and 26 weeks. Here we report that the mRNA levels of macrophage and inflammation associated genes were strongly upregulated at different time points in adipose tissues (6-16 weeks and liver (16-26 weeks, after the start of HFC feeding. CD11b+ and CD11c+ macrophages highly infiltrated HFC liver at 16 and 26 weeks. We found clear evidence that signals for IL-1β, IL1RN, TNF-α and TGFβ-1 are present in both adipose and liver tissues and that these are linked to the development of inflammation and insulin resistance in the HFC-fed mice. Conclusions Macrophage infiltration accompanied by severe inflammation and metabolic changes occurred in both adipose and liver tissues with a temporal shift in these signals depending upon the duration of HFC feeding. The evidences of gene expression profile, elevated serum alanine aminotransferase, and histological data support a progression towards nonalcoholic fatty liver disease and steatohepatitis in these HFC-fed mice within the

  13. Dynamics of soil organic carbon in density fractions during post-agricultural succession over two lithology types, southwest China.

    Science.gov (United States)

    Wen, Li; Li, Dejun; Chen, Hao; Wang, Kelin

    2017-10-01

    Agricultural abandonment has been proposed as an effective way to enhance soil organic carbon (SOC) sequestration. Nevertheless, SOC sequestration in the long term is largely determined by whether the stable SOC fractions will increase. Here the dynamics of SOC fractions during post-agricultural succession were investigated in a karst region, southwest China using a space-for-time substitution approach. Cropland, grassland, shrubland and secondary forest were selected from areas underlain by dolomite and limestone, respectively. Density fractionation was used to separate bulk SOC into free light fraction (FLFC) and heavy fraction (HFC). FLFC contents were similar over dolomite and limestone, but bulk SOC and HFC contents were greater over limestone than over dolomite. FLFC content in the forest was greater than in the other vegetation types, but bulk SOC and HFC contents increased from the cropland through to the forest for areas underlain by dolomite. The contents of bulk SOC and its fractions were similar among the four vegetation types over limestone. The proportion of FLFC in bulk SOC was higher over dolomite than over limestone, but the case was inverse for the proportion of HFC, indicating SOC over limestone was more stable. However, the proportions of both FLFC and HFC were similar among the four vegetation types, implying that SOC stability was not changed by cropland conversion. Exchangeable calcium explained most of the variance of HFC content. Our study suggests that lithology not only affects SOC content and its stability, but modulates the dynamics of SOC fractions during post-agricultural succession. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. Antioxidant properties of caroot juices and their impact on intestinal and probiotic bacteria

    Directory of Open Access Journals (Sweden)

    Aleksandra Duda-Chodak

    2015-08-01

    Full Text Available There is a growing interest in non-dairy probiotic products. The main aim of the study was to evaluate the impact of juice prepared from 15 various cultivars of carrot on the growth of representatives of human intestinal microbiota (Bifidobacterium catenulatum, Escherichia coli and probiotic strains (Lactobacillus acidophilus LA-5, Lactobacillus casei 01. Carrot juice was added to liquid medium at a final concentration of 5.0% and their impact on the bacteria number was assessed by measurement of the turbidity after 24 h of culture. The number of cells was expressed as % of positive control (medium without juice addition. Juices prepared from all tested cultivars of carrot inhibited the growth of Bifidobacterium catenulatum, and the strongest inhibitory effect was observed for juices obtained from the 'Kongo F1' cultivar (3.40 ±2.85% of positive control, 'Rumba F1'(4.17 ±2.27% and 'Broker F1' (5.35 ±2.14%. The majority of tested juices also inhibited the growth of E. coli, but those prepared from the 'Niland F1', 'Napa F1', 'Afro F1'and 'Samba F1' cultivars stimulated the growth of this bacterium. The probiotic strains were less sensitive to carrot juice impact than intestinal species, however both stimulation and inhibition could be observed. Juices made from the cultivars 'Kongo F1' and 'Deep Purple F1' acted negatively on the growth of both probiotic strains, while juice from 'Bangor F1' cultivar inhibited L. casei 01 growth, but stimulated the growth of LA-5. The obtained results suggest that 'Kongo F1' and 'Deep Purple F1' cultivars are not suitable as an additive or raw material for the production of probiotic products, because of their inhibitory properties against probiotic strains. Concluding, carrots can be used as raw material for the production of probiotic beverages, however both the cultivar of carrot and the strains of probiotic bacteria used for the production should be selected carefully. The most suitable for production of

  15. Non azeotrope mixing refrigerating fluids condensation outside of an horizontal tubes stack; Condensation de melanges non azeotropes de fluides frigorigenes a l'exterieur d'un faisceau de tubes horizontaux

    Energy Technology Data Exchange (ETDEWEB)

    Signe, J.Ch.

    1999-04-16

    The development of non-azeotrope mixing, as regular refrigerating fluids substitute, calls in question the experience for the design of refrigerating and cooling machinery. Studies to better understand these fluids behaviour are necessary. The aim of this thesis is the knowledge enlargement on the pure fluids and non azeotrope mixing condensation, outside of a tubes stack, and to simulate the heat transfers. The tubes stack is a condenser, type TEMA X often used in refrigerating machinery. The binary mixing HFC 134a-HFC23, allows a large sliding scale. (A.L.B.)

  16. New use of ammonia in heat pumps; Nouvelle utilisation de l`ammoniac en pompe a chaleur

    Energy Technology Data Exchange (ETDEWEB)

    Hivet, B.; Ducruet, C. [Electricite de France, 77 - Moret sur Loing (France). Direction des Etudes et Recherches

    1996-12-31

    According to simple thermodynamic criteria and to pollution regulations, ammonia and HFC 134a are the only refrigerating fluids that can be used in heat pumps. Ammonia is particularly performing at high condensation temperatures. However, its use has become possible thanks to the use of industrial refrigerating compressors with a maximum operation pressure of 40 bars. Test results confirm the interesting thermal performances of this fluid. A comparison with the HFC 134a refrigerant indicates that ammonia leads to equal or better coefficients of performance for higher volume powers. Two applications taken in the agriculture and food industries are presented. (J.S.)

  17. Hiperlipidemia familiar combinada: documento de consenso

    OpenAIRE

    Pedro Mata; Rodrigo Alonso; Antonio Ruíz-Garcia; Jose L. Díaz-Díaz; Noemí González; Teresa Gijón-Conde; Ceferino Martínez-Faedo; Ignacio Morón; Ezequiel Arranz; Rocío Aguado; Rosa Argueso; Leopoldo Perez de Isla

    2014-01-01

    La hiperlipidemia familiar combinada (HFC) es un trastorno muy frecuente asociado a enfermedad coronaria prematura. Se transmite de forma autosómica dominante, aunque no existe un gen único asociado al trastorno. El diagnóstico se realiza mediante criterios clínicos, y son importantes la variabilidad del fenotipo lipídico y la historia familiar de hiperlipidemia. Es frecuente la asociación con diabetes mellitus tipo 2, hipertensión arterial y obesidad central. Los pacientes con HFC se cons...

  18. Research and Development Opportunities for Joining Technologies in HVAC&R

    Energy Technology Data Exchange (ETDEWEB)

    Goetzler, William [Navigant Consulting, Burlington, MA (United States); Guernsey, Matt [Navigant Consulting, Burlington, MA (United States); Young, Jim [Navigant Consulting, Burlington, MA (United States)

    2015-10-01

    The Building Technologies Office (BTO) works with researchers and industry partners to develop and deploy technologies that can substantially reduce energy consumption and greenhouse gas (GHG) emissions in residential and commercial buildings. This opportunity assessment aims to advance BTO’s energy savings, GHG reduction, and other program goals by identifying research and development (R&D) initiatives for joining technologies in heating, ventilation, air-conditioning, and refrigeration (HVAC&R) systems. Improving joining technologies for HVAC&R equipment has the potential to increase lifetime equipment operating efficiency, decrease equipment and project cost, and most importantly reduce hydroflourocarbon (HFC) refrigerant leakage to support HFC phasedown and GHG reduction goals.

  19. Hydrochlorofluorocarbon and hydrofluorocarbon emissions in East Asia determined by inverse modeling

    Directory of Open Access Journals (Sweden)

    A. Stohl

    2010-04-01

    Full Text Available The emissions of three hydrochlorofluorocarbons, HCFC-22 (CHClF2, HCFC-141b (CH3CCl2F and HCFC-142b (CH3CClF2 and three hydrofluorocarbons, HFC-23 (CHF3, HFC-134a (CH2FCF3 and HFC-152a (CH3CHF2 from four East Asian countries and the Taiwan region for the year 2008 are determined by inverse modeling. The inverse modeling is based on in-situ measurements of these halocarbons at the Japanese stations Cape Ochi-ishi and Hateruma, the Chinese station Shangdianzi and the South Korean station Gosan. For every station and every 3 h, 20-day backward calculations were made with the Lagrangian particle dispersion model FLEXPART. The model output, the measurement data, bottom-up emission information and corresponding uncertainties were fed into an inversion algorithm to determine the regional emission fluxes. The model captures the observed variation of halocarbon mixing ratios very well for the two Japanese stations but has difficulties explaining the large observed variability at Shangdianzi, which is partly caused by small-scale transport from Beijing that is not adequately captured by the model. Based on HFC-23 measurements, the inversion algorithm could successfully identify the locations of factories known to produce HCFC-22 and emit HFC-23 as an unintentional byproduct. This lends substantial credibility to the inversion method. We report national emissions for China, North Korea, South Korea and Japan, as well as emissions for the Taiwan region. Halocarbon emissions in China are much larger than the emissions in the other countries together and contribute a substantial fraction to the global emissions. Our estimates of Chinese emissions for the year 2008 are 65.3±6.6 kt/yr for HCFC-22 (17% of global emissions extrapolated from Montzka et al., 2009, 12.1±1.6 kt/yr for HCFC-141b (22%, 7.3±0.7 kt/yr for HCFC-142b (17%, 6.2±0.7 kt/yr for HFC

  20. Studies of bone marrow scintigrams with sup(99m)technetium sulfur colloid on various hematological disorders

    International Nuclear Information System (INIS)

    Mizuno, Takashi

    1984-01-01

    One hundred and eighty-five bone marrow scintigraphy on the whole body was performed on eight healthy adults and 151 patients with various hematologic diseases including 64 leukemia, 41 anemia, 23 other malignancy, etc. The positions of the investigated bone marrow were divided into the central marrow (five positions on the trunk bones) and the peripheral marrow (11 positions on the upper and 11 positions on the lower extremities) on the scintigram. The bone marrow scintigram was estimated by following three criteria. The first, ''Yuu-ryoiki'' (positive area), was the existence of sup(99m)Tc sulfur colloid accumulation on bone marrow (two grades; presence or absence). The second, ''Bunpu-kei'' (distribution form), was the extent of the sup(99m)Tc accumulation area of the investigated bone marrow and was divided into five grades. The last, ''Kido'' (intensity of radioactivity), was the density of the sup(99m)Tc accumulation on the area and was divided into five grades. Using this estimation, in the diseases with bone marrow hyperplasia such as Primary Thrombocythemia and Hemolytic Anemia, ''Yuu-ryoiki'' was enlarged, ''Bunpu-kei'' was extended, and ''Kido'' was increased comparing with those in healty adult. In contrast, in the diseases with bone marrow hypoplasia such as Myelofibrosis and Aplastic Anemia, ''Yuu-ryoiki'' was reduced, ''Bunpu-kei'' was contracted, and ''Kido'' was decreased. However, the enlargement of ''Yuu-ryoiki'' did not always mean bone marrow hyperplasia. The author could evaluate not only the range and distribution of hemopoiesis as a whole in malignant or benign diseases but also the residual effective hemopoiesis to know the suitable time of the initiation of the therapy or to predict the prognosis of these cases. In this study it was shown that the bone marrow scintigraphy with sup(99m)Tc sulfur colloid was an useful method to estimate the hemopoietic activity of the bone marrow. (J.P.N.)

  1. Selvitys palkanlaskennan ulkoistamisen hyödyistä ja haasteista

    OpenAIRE

    Pohjonen, Anna

    2013-01-01

    Opinnäytetyön tavoitteena oli selvittää sekä oman palkanlaskennan että ulkoistetun palkanlaskennan hyödyt ja haasteet. Analyysin pohjalta oli tarkoituksena ehdottaa toimeksiantajan tarpeisiin sopivaa toimintamallia palkanlaskennan toteuttamiseen. Selvityshetkellä oli käytössä sisäinen palkanlaskentapalvelu, jonka toteuttamisesta vastasi yksi henkilö. Ulkoistetun palkanlaskennan vaihtoehto oli noussut toimeksiantajayrityksessä esille nykyisen palkanlaskijan eläkeiän lähestyessä. Myös muiden sa...

  2. YLEISIMMÄT URHEILUVAMMAT PAINONNOSTOSSA JA TURVALLINEN NOSTOTEKNIIKKA NIIDEN ENNALTAEHKÄISYYN

    OpenAIRE

    Heiskanen, Henri; Kokko, Ville-Pekka

    2015-01-01

    Painonnoston harjoittelu on lisääntynyt viime vuosina trendilaji CrossFitin suosion myötä. Painonnosto on teknisyytensä ja raskaiden nostokuormien takia vamma-altis laji. Tämä opinnäytetyö on epäsystemaattinen kirjallisuuskatsaus. Sen tehtävänä oli selvittää, mitkä ovat yleisimmät urheiluvammat painonnostoa harrastavilla, miten kyseiset vammat syntyvät, millainen on turvallinen nostotekniikka vammojen ennaltaehkäisyyn sekä miten urheiluvammoja voidaan ennaltaehkäistä lajissa fysioterapian kei...

  3. The Shock and Vibration Bulletin. Part 4. Dynamic Properties of Materials, Applications of Materials, Shock and Blast, Fragments

    Science.gov (United States)

    1980-09-01

    individual m.crophone readings using the following standard formula: SPI- AVE " ,0 LOG ( S lOSPM/lo/n) i*I ’ where: SPLAVE " Sound pressure...Godes- berg 1975 |4| NEIER-DemBERG. K.-E.i ’Reference Pa- rameters for Shock Inputs and Shock Tolerance Limits. ACARO Conference Proceedings No...occurrence In the Polsson counting process, equals v.{t), the av - erage barrier crossing rate of the response ran- dom process for a barrier with

  4. Strateginis paslaugų kokybės viešajame sektoriuje valdymas: Klaipėdos regiono aprūpinimo elektros energija atvejis

    OpenAIRE

    Tamošiūnas, Teodoras; Pečiulytė, Sandra

    2010-01-01

    Tyrimo aktualumas ir problematika. Europos šalyse pastebimas viešojo sektoriaus modernizavimas, pritaikant naujausius, pažangiausius vadybos modelius, tarp jų – ir naujosios viešosios vadybos (Židonis, Rudnickas, 2005). Žvelgiant sistemiškai į šiuo metu keičiamus Lietuvos teisės aktus, matyti, kad viešajame sektoriuje rengiama norminė bazė, kuri gali būti tinkamas teisinis pagrindas įgyvendinant naujus viešojo administravimo principus (Vanagas, 2006). Teorinius strateginio kokybės valdymo asp...

  5. Thermomechanical Fatigue Behavior of a Silicon Carbide Fiber-Reinforced Calcium Aluminosilicate Glass-Ceramic Matrix Composite.

    Science.gov (United States)

    1992-08-01

    Testing of Coated Monocrystalline Superalloys," in Low Cycle Fatigue. ASTM STP 942, Solomon, H.D., Hafford, G.R., Kaisand, L.R., and Keis, B.N. , eds...HOTOL) project is considering the use of CMCs on lower aeroshell panels , air intake leading edges, and the nose cone where temperatures may climb to...Works (Corning, NY). The composite was supplied in 16-ply, unidirectionally reinforced (10116) panels , measuring 152.4 cm x 152.4 cm (6 in x 6 in

  6. Rapid Airlift Planning for Amphibious-Ready Groups

    Science.gov (United States)

    2015-09-01

    to balance enhanced risk-mitigation versus reduced travel time. 8 Timlin and Pulleyblank (1992) develop a precedence-constrained traveling...that j can conduct flight operations in block 1 peni , j ,k penalty per unit of PMC-type k not moved from i to j tpenl ,h penalty for...j ,h l ∑ Xi, j ,l ,h (i, j ,h)|(i, j ,h)∈HARC ∑ + peni , j ,kEi, j ,k k ∑ (i, j )|(i, j )∈ARCS ∑ + costmlMi,l , j ,l ’,k ,h k ∑ (l ,l ’)|l<l ’ ∑ (i

  7. Nuclear methods in national development

    International Nuclear Information System (INIS)

    1993-01-01

    This volume of the proceedings of the First National Conference on Nuclear Methods held at Kongo Conference Hotel Zaria from 2-4 September 1993, contains the full text of about 30 technical papers and speeches of invited dignitaries presented at the conference. The technical papers are original or review articles containing results and experiences in nuclear and related analytical techniques. Topics treated include neutron generator operation and control, nuclear data, application of nuclear techniques in environment, geochemistry, medicine, biology, agriculture, material science and industries. General topics in nuclear laboratory organization and research experiences were also covered. The papers were fully discussed during the conference and authors were requested to make changes in the manuscripts where necessary. However, they were further edited. The organizing committee wishes to thank all authors for their presentation and cooperation in submitting their manuscripts promptly and the participants for their excellent contribution during the conference

  8. İlköğretim Öğretmen Adaylarının Tarım Kaynaklı Güncel Kavramlar Hakkındaki Farkındalıklarının Tespiti

    Directory of Open Access Journals (Sweden)

    Hasan AKGUL

    2011-12-01

    Full Text Available Yapılan araştırma ile öğretmen adaylarının son yıllarda ortaya çıkan tarımsal kaynaklı güncel sorunlar hakkındaki farkındalıklarının belirlenmesi amaçlanmıştır. Özellikle küresel ısınma ve buna bağlı olarak ortaya çıkan kuş gribi ve kanamalı kırım Kongo ateşi hastalığı ve hayvanlara tekniğine uygun olamayan yem hazırlanması sonucu ortaya çıkan deli dana hastalığı konusunda 383 öğretmen adayına anket soruları sorulmuştur. Araştırma nicel ve nitel tekniklerin birlikte kullanıldığı bir tarama çalışmasıdır. Anket sonuçları SPSS 15,0 istatistik programına göre değerlendirilmiştir. Sonuçta ilköğretim öğretmen adaylarının küresel ısınmanın etkileri konusunda bilgi sahibi olduğu saptanmıştır. Araştırmaya katılan öğretmen adaylarının hemen hepsi deli dana hastalığı ve ortaya çıkardığı sonuçlar ile kuş gribi hastalığının tanım ve sonuçları konusunda doğru bilgiye sahiptirler. Bununla birlikte adayların çoğu Kırım Kongo Kanamalı Ateşi hastalığına sebep olan kenelerin kuş gribine bağlı tavuk itlafı ile çoğaldıklarını düşünmektedirler ve kanamalı kırım Kongo ateşi hastalığına neden olan kenelerin çoğalmasının küresel ısınma ile ilgili olmadığı konusunda yanlış bir yargıya sahip oldukları belirlenmiştir. Anahtar kelimeler: tarımsal kavramlar, küresel ısınma, kanamalı kırım Kongo ateşi, deli dana, kuş gribi, tarımsal farkındalık

  9. 40 CFR Appendix A to Subpart G of... - Substitutes Subject to Use Restrictions and Unacceptable Substitutes

    Science.gov (United States)

    2010-07-01

    ... safely in this end-use. CFC-12, motor vehicle air conditioners (retrofit) HCFC-22/HFC-142b/CFC-12... to demonstrate it can be used safely in this end-use. CFC-12, motor vehicle air conditioners (new... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE...

  10. Lifetime prediction of EC, DPA, akardite II and MNA stabilized triple base propellants, comparison of heat generation rate and stabilizer consumption

    NARCIS (Netherlands)

    Boers, M.N.; Klerk, W.P.C. de

    2005-01-01

    A lifetime prediction study is carried out on four triple base propellant compositions by artificial ageing. The ageing effects are studied with High Performance Liquid Chromatography (HPLC) and Heat Flow Calorimetry (HFC) in order to find the most effective stabilizer and to evaluate the advantages

  11. Journal of Earth System Science | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    An integrated assessment of emissions of some important refrigerant ozone depleting substances (ODSs) (CFC-11, CFC-12, HCFC-141b and HFC-134a) and their contributed ozone depletion potentials (ODPs) and global warming potentials (GWPs) have been made in the megacity Lahore (Pakistan) for the periodfrom ...

  12. Evaluation of cermet materials suitable for lithium lubricated thrust bearings for high temperature operation

    Science.gov (United States)

    Sinclair, J. H.; Hendrixson, W. H.

    1974-01-01

    Cerment materials (HfC - 10 wt% W; HfC - 10 wt% TaC - 10 wt%W; HfC - 2 wt% CbC - 8 wt% Mo;Hfn - 10 wt% W; Hfn - 10 wt% TaN - 10 wt% W; and ZrC - 17 wt% W) were evaluated for possible use as lithium-lubricated bearings in the control system of a nuclear reactor. Tests of compatibility with lithium were made in T-111 (Ta-8W-2Hf) capsules at temperatures up to 1090 C. The tendencies of HfC-TaC-W, HfC-CbC-Mo, and HfN-W to bond to themselves and to the refractory alloys T-111 and TZM when enclosed in lithium-filled capsules under a pressure of 2000 psi at 980 and 1200 C for 1933 hours were evaluated. Thermal expansion characteristics were determined for the same three materials from room temperature to 1200 C. On the basis of these tests, HfC-10 TaC-10W and HfN-10W were selected as the best and second best candidates, respectively, of the materials tested for the bearing application.

  13. Effect of aerobic exercise and diet on liver fat in pre-diabetic patients with non-alcoholic-fatty-liver-disease : A randomized controlled trial

    NARCIS (Netherlands)

    Cheng, Sulin; Ge, Jun; Zhao, Can; Le, Shenglong; Yang, Yifan; Ke, Dandan; Wu, Na; Tan, Xiao; Zhang, Xiaobo; Du, Xiaming; Sun, Jianqin; Wang, Renwei; Shi, Yongyong; Borra, Ronald J. H.; Parkkola, Riitta; Wiklund, Petri; Lu, Dajiang

    2017-01-01

    The study aimed to assess whether aerobic exercise (AEx) training and a fibre-enriched diet can reduce hepatic fat content (HFC) and increase glycaemic control in pre-diabetic patients with non-alcoholic fatty liver disease (NAFLD). Six-hundred-and-three patients from seven clinics in Yangpu

  14. Effect of anti-gut inflammatory agent on insulin resistance and lipid ...

    African Journals Online (AJOL)

    Purpose: To further explore the effect of 5-aminosalicylic acid (5-ASA) treatment on lipid levels in mice fed different ... insulin and the curve of glucose tolerance test (GTT) in mice fed LFD, HFD or HFC diet were not affected by ... diabetes, the extent to which gut inflammation .... and homeostasis of glucose in diet-induced.

  15. Hafnium carbide nanocrystal chains for field emitters

    International Nuclear Information System (INIS)

    Tian, Song; Li, Hejun; Zhang, Yulei; Ren, Jincui; Qiang, Xinfa; Zhang, Shouyang

    2014-01-01

    A hafnium carbide (HfC) nanostructure, i.e., HfC nanocrystal chain, was synthesized by a chemical vapor deposition (CVD) method. X-ray diffractometer, field-emission scanning electron microscope, transmission electron microscope, and energy-dispersive X-ray spectrometer were employed to characterize the product. The synthesized one-dimensional (1D) nanostructures with many faceted octahedral nanocrystals possess diameters of tens of nanometers to 500 nm and lengths of a few microns. The chain-like structures possess a single crystalline structure and preferential growth direction along the [1 0 0] crystal orientation. The growth of the chains occurred through the vapor–liquid–solid process along with a negative-feedback mechanism. The field emission (FE) properties of the HfC nanocrystal chains as the cold cathode emitters were examined. The HfC nanocrystal chains display good FE properties with a low turn-on field of about 3.9 V μm −1 and a high field enhancement factor of 2157, implying potential applications in vacuum microelectronics.

  16. Lattice vibrational properties of transition metal carbides (TiC, ZrC

    Indian Academy of Sciences (India)

    Lattice vibrational properties of transition metal carbides (TiC, ZrC and HfC) have been presented by including the effects of free-carrier doping and three-body interactions in the rigid shell model. The short-range overlap repulsion is operative up to the second neighbour ions. An excellent agreement has been obtained ...

  17. 40 CFR Appendix F to Subpart B of... - Standard for Recover-Only Equipment That Extracts a Single, Specific Refrigerant Other Than CFC...

    Science.gov (United States)

    2010-07-01

    ... does not recycle, any single, specific automotive refrigerant other than CFC-12 or HFC-134a, including... or equivalent new product specifications before reuse in a mobile air-conditioning system.” The... capable of ensuring removal of refrigerant from the system being serviced by reducing the system pressure...

  18. Fire and explosion hazards of refractory compound powders

    International Nuclear Information System (INIS)

    Krivtsov, V.A.; Kostina, E.S.

    1978-01-01

    Data on fire and explosion hazards of refractory compound powders (HfC, ZrC,LaB 6 , ZrN, etc.) are presented. It is shown that refractory compounds can be fire- and exposion hazardous in various degrees. Qualitative and quantitative estimations of one of fire-hazard characteristics - smoldering temperature - are presented

  19. Upgrade of hybrid fibre coax networks towards bi-directional access

    NARCIS (Netherlands)

    Khoe, G.D.; Wolters, R.P.C.; Boom, van den H.P.A.; Prati, G.

    1997-01-01

    In this paper we describe an upgrade scenario for Hybrid Fibre Coax (HFC) CATV Networks towards hi-directional access. The communication system described has been newly designed, and is based on the use of Direct Sequence- Code Division Multiple-Access (DS-CDMA). Due to its spread-spectrum

  20. Lifetime prediction of EC, DPA, Akardite II and MNA stabilized triple base propellants, comparison of heat generation rate and stabilizer consumption

    Energy Technology Data Exchange (ETDEWEB)

    Boers, Marco N.; Klerk, Willem (Wim) P.C. de [TNO Defence, Security and Safety, P. O. Box 45, 2280 AA Rijswijk ZH (Netherlands)

    2005-10-01

    A lifetime prediction study is carried out on four triple base propellant compositions by artificial ageing. The ageing effects are studied with High Performance Liquid Chromatography (HPLC) and Heat Flow Calorimetry (HFC) in order to find the most effective stabilizer and to evaluate the advantages and disadvantages of both methods. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

  1. CITEPA/ inventory UNFCCC December 2004

    International Nuclear Information System (INIS)

    2004-01-01

    This document provides statistical data on the greenhouse gases emissions PNLCCC in France. A first table presents the CO 2 emissions from 1990 to 2003. Others tables detail all the greenhouse gases (CH 4 , N 2 O, HFC, PFC and SF 6 ) emissions, per sector from 1990 to 2003. (A.L.B.)

  2. 75 FR 45130 - Draft Compliance Policy Guide Sec. 690.800 Salmonella

    Science.gov (United States)

    2010-08-02

    ... humans, such as pet food and pet treats, contaminated with Salmonella and also on regulatory policy... Compliance Policy (HFC-230), Office of Enforcement, Food and Drug Administration, 5600 Fishers Lane, Rockville, MD 20857. Send two self-addressed adhesive labels to assist that office in processing your...

  3. Evaluating the Impact of a Connecticut Program to Reduce Availability of Unhealthy Competitive Food in Schools

    Science.gov (United States)

    Long, Michael W.; Henderson, Kathryn E.; Schwartz, Marlene B.

    2010-01-01

    Background: This article seeks to inform state and local school food policies by evaluating the impact of Connecticut's Healthy Food Certification (HFC), a program which provides monetary incentives to school districts that choose to implement state nutrition standards for all foods sold to students outside reimbursable school meals. Methods: Food…

  4. Effect of anti-gut inflammatory agent on insulin resistance and lipid ...

    African Journals Online (AJOL)

    The level of fasting blood glucose, fasting plasma insulin and the curve of glucose tolerance test (GTT) in mice fed LFD, HFD or HFC diet were not affected by 5-ASA treatment. Although plasma lipid levels were similar between 5-ASA consuming and non-5-ASA groups in mice fed LFD and HFD, improved lipid profile was ...

  5. Rate constants for the reactions of OH with CH3Cl, CH2Cl2, CHCl3, and CH3Br

    Science.gov (United States)

    Hsu, K.-J.; Demore, W. B.

    1994-01-01

    Rate constants for the reactions of OH with CH3Cl, CH2Cl2, CHCl3, and CH3Br have been measured by a relative rate technique in which the reaction rate of each compound was compared to that of HFC-152a (CH3CHF2) and (for CH2Cl2) HFC-161 (CH3CH2F). Using absolute rate constants for HFC-152a and HFC-161, which we have determined relative to those for CH4, CH3CCl3, and C2H6, temperature dependent rate constants of both compounds were derived. The derived rate constant for CH3Br is in good agreement with recent absolute measurements. However, for the chloromethanes all the rate constants are lower at atmospheric temperatures than previously reported, especially for CH2Cl2 where the present rate constant is about a factor of 1.6 below the JPL 92-20 value. The new rate constant appears to resolve a discrepancy between the observed atmospheric concentrations and those calculated from the previous rate constant and estimated release rates.

  6. Photoacoustic-Based-Close-Loop Temperature Control for Nanoparticle Hyperthermia.

    Science.gov (United States)

    Xiaohua, Feng; Fei, Gao; Yuanjin, Zheng

    2015-07-01

    Hyperthermia therapy requires tight temperature control to achieve selective killing of cancerous tissue with minimal damage on surrounding healthy tissues. To this end, accurate temperature monitoring and subsequent heating control are critical. However, an economic, portable, and real-time temperature control solution is currently lacking. To bridge this gap, we present a novel portable close-loop system for hyperthermia temperature control, in which photoacoustic technique is proposed for noninvasive real-time temperature measurement. Exploiting the high sensitivity of photoacoustics, the temperature is monitored with an accuracy of around 0.18 °C and then fed back to a controller implemented on field programmable gate array (FPGA) for temperature control. Dubbed as portable hyperthermia feedback controller (pHFC), it stabilizes the temperature at preset values by regulating the hyperthermia power with a proportional-integral-derivative (PID) algorithm; and to facilitate digital implementation, the pHFC further converts the PID output into switching values (0 and 1) with the pulse width modulation (PWM) algorithm. Proof-of-concept hyperthermia experiments demonstrate that the pHFC system is able to bring the temperature from baseline to predetermined value with an accuracy of 0.3° and a negligible temperature overshoot. The pHFC can potentially be translated to clinical applications with customized hyperthermia system design. This paper can facilitate future efforts in seamless integration of close-loop temperature control solution and various clinical hyperthermia systems.

  7. Flammable refrigerants

    NARCIS (Netherlands)

    Gerwen, R.J.M. van; Verwoerd, M.; Oostendorp, P.A.

    1999-01-01

    Hydrocarbons are promising alternatives for CFC, HCFC and HFC refrigerants. Due to their flammable nature, safety aspects have to be considered carefully. The world-wide situation concerning acceptability and practical application of flammable refrigerants is becoming more and more complex and

  8. Performance and energy saving analysis of a refrigerator using hydrocarbon mixture (HC-R134a) as working fluid

    Science.gov (United States)

    Mohtar, M. N.; Nasution, H.; Aziz, A. A.

    2015-12-01

    The use of hydrocarbon mixture as a working fluid in a refrigerator system is rarely explored. Almost all domestic refrigerators use hydroflourocarbon R134a (HFC-R134a) as refrigerants. In this study, hydrocarbon gas (HC-R134a) is used as the alternative refrigerant to replace HFC-R134a. It has a composition of R290 (56%), R600a (54.39%) and additive (0.1%wt) blended for the trials. The experiments were conducted with 105 g and 52.5 g refrigerant mass charge, subjected to internal heat load of 0, 1, 2, 3 and 4 kg respectively. The study investigates the coefficient of performance of the refrigerator (COPR) and energy consumption. The results show that the use of HC-R134a as the replaceable refrigerant can save energy ranging from 2.04% to 7.09%, as compared to the conventional HFC-R134a refrigerant. Naturally, the COPR improvement and temperature distribution using HC-R134a are much better than HFC-R134a

  9. Proceedings of the 1993 non-fluorocarbon insulation, refrigeration and air conditioning technology workshop

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    Sessions included: HFC blown polyurethanes, carbon dioxide blown foam and extruded polystyrenes, plastic foam insulations, evacuated panel insulation, refrigeration and air conditioning, absorption and adsorption and stirling cycle refrigeration, innovative cooling technologies, and natural refrigerants. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database.

  10. An overview on non-CO2 greenhouse gases

    NARCIS (Netherlands)

    Pulles, T.; Amstel, van A.R.

    2010-01-01

    Non-CO2 greenhouse gases, included in the Kyoto Protocol, are methane (CH4), nitrous oxide (N2O), hexafluorocarbons (HFC), perfluorinated compounds (PFC) and sulphur hexafluoride (SF6). Together they account for about 25% of the present global greenhouse gas emissions. Reductions in emissions of

  11. 76 FR 71042 - Scott S. Reuben: Debarment Order

    Science.gov (United States)

    2011-11-16

    ... CONTACT: Kenny Shade, Division of Compliance Policy (HFC-230), Office of Enforcement, Office of Regulatory...: Dr. Reuben was a physician licensed by the State of Massachusetts working as an anesthesiologist... Western Massachusetts and maintained an office at the hospital for the purpose of conducting research. Dr...

  12. Emission estimates of HCFCs and HFCs in California from the 2010 CalNex study

    Science.gov (United States)

    Barletta, Barbara; Carreras-Sospedra, Marc; Cohan, Alex; Nissenson, Paul; Dabdub, Donald; Meinardi, Simone; Atlas, Elliot; Lueb, Rich; Holloway, John S.; Ryerson, Thomas B.; Pederson, James; VanCuren, Richard A.; Blake, Donald R.

    2013-02-01

    The CalNex 2010 (California Research at the Nexus of Air Quality and Climate Change) study was designed to evaluate the chemical composition of air masses over key source regions in California. During May to June 2010, air samples were collected on board a National Oceanic and Atmospheric Administration (NOAA) WP-3D aircraft over the South Coast Air Basin of California (SoCAB) and the Central Valley (CV). This paper analyzes six effective greenhouse gases—chlorodifluoromethane (HCFC-22), 1,1-dichloro-1-fluoroethane (HCFC-141b), 1-chloro-1,1-difluoroethane (HCFC-142b), 2-chloro-1,1,1,2-tetrafluoroethane (HCFC-124), 1,1,1,2-tetrafluoroethane (HFC-134a), and 1,1-difluoroethane (HFC-152a)—providing the most comprehensive characterization of chlorofluorocarbon (CFC) replacement compound emissions in California. Concentrations of measured HCFCs and HFCs are enhanced greatly throughout the SoCAB and CV, with highest levels observed in the SoCAB: 310 ± 92 pptv for HCFC-22, 30.7 ± 18.6 pptv for HCFC-141b, 22.9 ± 2.0 pptv for HCFC-142b, 4.86 ± 2.56 pptv for HCFC-124, 109 ± 46.4 pptv for HFC-134a, and 91.2 ± 63.9 pptv for HFC-152a. Annual emission rates are estimated for all six compounds in the SoCAB using the measured halocarbon to carbon monoxide (CO) mixing ratios and CO emissions inventories. Emission rates of 3.05 ± 0.70 Gg for HCFC-22, 0.27 ± 0.07 Gg for HCFC-141b, 0.06 ± 0.01 Gg for HCFC-142b, 0.11 ± 0.03 Gg for HCFC-124, 1.89 ± 0.43 Gg for HFC-134a, and 1.94 ± 0.45 Gg for HFC-152b for the year 2010 are calculated for the SoCAB. These emissions are extrapolated from the SoCAB region to the state of California using population data. Results from this study provide a baseline emission rate that will help future studies determine if HCFC and HFC mitigation strategies are successful.

  13. Chocolate flavanols and skin photoprotection: a parallel, double-blind, randomized clinical trial.

    Science.gov (United States)

    Mogollon, Jaime Andres; Boivin, Catherine; Lemieux, Simone; Blanchet, Claudine; Claveau, Joël; Dodin, Sylvie

    2014-06-27

    Solar ultraviolet (UV) radiation has deleterious effects on the skin, including sunburn, photoaging and cancer. Chocolate flavanols are naturally-occurring antioxidant and anti-inflammatory molecules that could play a role in preventing cutaneous UV damage. We investigated the influence of 12-week high-flavanol chocolate (HFC) consumption on skin sensitivity to UV radiation, measured by minimal erythema dose (MED). We also evaluated skin elasticity and hydration. In this 2-group, parallel, double-blind, randomized controlled trial, 74 women aged 20-65 years and Fitzpatrick skin phototypes I or II were recruited from the general community in Quebec City, for randomization to either HFC (n = 33) or low-flavanol chocolate (LFC) (n = 41). A blocked randomisation (4), considering date of entry, skin type and age as factors, generated a sequentially-numbered allocation list. Study participants and research assistants were blinded. Totally, 30 g of chocolate were consumed daily for 12 weeks, followed by a 3-week washout period. MED was assessed at baseline and at 6, 9, 12 and 15 weeks. Main outcome was changes in MED at week 12. 33 participants in the HFC group and 41 in the LFC group were analyzed with 15 weeks of follow-up. Both groups showed similarly-increased MED at 12 weeks (HFC: 0.0252 ± 0.1099 J/cm2 [mean ± standard deviation (SD)]; LFC: 0.0151 ± 0.1118; mean difference (MD): 0.0100 J/cm2; 95% confidence interval (CI): -0.0417 to 0.0618). However, after 3-week washout, the HFC group presented decreased MED (-0.0248 ± 0.1145) whereas no effect was seen in the LFC group (0.0168 ± 0.1698) (MD: -0.0417; 95% CI: -0.1106 to 0.0272). Net temple elasticity increased slightly but significantly by 0.09 ± 0.12 mm in the HFC group at 12 weeks compared to 0.02 ± 0.12 mm in the LFC group (MD: 0.06; 95% CI: 0.01 to 0.12 ). No significant adverse events were reported. Our study failed to demonstrate a statistically

  14. Chocolate flavanols and skin photoprotection: a parallel, double-blind, randomized clinical trial

    Science.gov (United States)

    2014-01-01

    Background Solar ultraviolet (UV) radiation has deleterious effects on the skin, including sunburn, photoaging and cancer. Chocolate flavanols are naturally-occurring antioxidant and anti-inflammatory molecules that could play a role in preventing cutaneous UV damage. We investigated the influence of 12-week high-flavanol chocolate (HFC) consumption on skin sensitivity to UV radiation, measured by minimal erythema dose (MED). We also evaluated skin elasticity and hydration. Methods In this 2-group, parallel, double-blind, randomized controlled trial, 74 women aged 20–65 years and Fitzpatrick skin phototypes I or II were recruited from the general community in Quebec City, for randomization to either HFC (n = 33) or low-flavanol chocolate (LFC) (n = 41). A blocked randomisation (4), considering date of entry, skin type and age as factors, generated a sequentially-numbered allocation list. Study participants and research assistants were blinded. Totally, 30 g of chocolate were consumed daily for 12 weeks, followed by a 3-week washout period. MED was assessed at baseline and at 6, 9, 12 and 15 weeks. Main outcome was changes in MED at week 12. Results 33 participants in the HFC group and 41 in the LFC group were analyzed with 15 weeks of follow-up. Both groups showed similarly-increased MED at 12 weeks (HFC: 0.0252 ± 0.1099 J/cm2 [mean ± standard deviation (SD)]; LFC: 0.0151 ± 0.1118; mean difference (MD): 0.0100 J/cm2; 95% confidence interval (CI): -0.0417 to 0.0618). However, after 3-week washout, the HFC group presented decreased MED (-0.0248 ± 0.1145) whereas no effect was seen in the LFC group (0.0168 ± 0.1698) (MD: -0.0417; 95% CI: -0.1106 to 0.0272). Net temple elasticity increased slightly but significantly by 0.09 ± 0.12 mm in the HFC group at 12 weeks compared to 0.02 ± 0.12 mm in the LFC group (MD: 0.06; 95% CI: 0.01 to 0.12 ). No significant adverse events were reported. Conclusion Our study failed to

  15. Abundance and sources of atmospheric halocarbons in the Eastern Mediterranean

    Directory of Open Access Journals (Sweden)

    F. Schoenenberger

    2018-03-01

    Full Text Available A wide range of anthropogenic halocarbons is released to the atmosphere, contributing to stratospheric ozone depletion and global warming. Using measurements of atmospheric abundances for the estimation of halocarbon emissions on the global and regional scale has become an important top-down tool for emission validation in the recent past, but many populated and developing areas of the world are only poorly covered by the existing atmospheric halocarbon measurement network. Here we present 6 months of continuous halocarbon observations from Finokalia on the island of Crete in the Eastern Mediterranean. The gases measured are the hydrofluorocarbons (HFCs, HFC-134a (CH2FCF3, HFC-125 (CHF2CF3, HFC-152a (CH3CHF2 and HFC-143a (CH3CF3 and the hydrochlorofluorocarbons (HCFCs, HCFC-22 (CHClF2 and HCFC-142b (CH3CClF2. The Eastern Mediterranean is home to 250 million inhabitants, consisting of a number of developed and developing countries, for which different emission regulations exist under the Kyoto and Montreal protocols. Regional emissions of halocarbons were estimated with Lagrangian atmospheric transport simulations and a Bayesian inverse modeling system, using measurements at Finokalia in conjunction with those from Advanced Global Atmospheric Gases Experiment (AGAGE sites at Mace Head (Ireland, Jungfraujoch (Switzerland and Monte Cimone (Italy. Measured peak mole fractions at Finokalia showed generally smaller amplitudes for HFCs than at the European AGAGE sites except for periodic peaks of HFC-152a, indicating strong upwind sources. Higher peak mole fractions were observed for HCFCs, suggesting continued emissions from nearby developing regions such as Egypt and the Middle East. For 2013, the Eastern Mediterranean inverse emission estimates for the four analyzed HFCs and the two HCFCs were 13.9 (11.3–19.3 and 9.5 (6.8–15.1 Tg CO2eq yr−1, respectively. These emissions contributed 16.8 % (13.6–23.3 % and 53.2 % (38.1–84.2

  16. Hollow Fluffy Co3O4 Cages as Efficient Electroactive Materials for Supercapacitors and Oxygen Evolution Reaction.

    Science.gov (United States)

    Zhou, Xuemei; Shen, Xuetao; Xia, Zhaoming; Zhang, Zhiyun; Li, Jing; Ma, Yuanyuan; Qu, Yongquan

    2015-09-16

    Nano-/micrometer multiscale hierarchical structures not only provide large surface areas for surface redox reactions but also ensure efficient charge conductivity, which is of benefit for utilization in areas of electrochemical energy conversion and storage. Herein, hollow fluffy cages (HFC) of Co3O4, constructed of ultrathin nanosheets, were synthesized by the formation of Co(OH)2 hollow cages and subsequent calcination at 250 °C. The large surface area (245.5 m2 g(-1)) of HFC Co3O4 annealed at 250 °C ensures the efficient interaction between electrolytes and electroactive components and provides more active sites for the surface redox reactions. The hierarchical structures minimize amount of the grain boundaries and facilitate the charge transfer process. Thin thickness of nanosheets (2-3 nm) ensures the highly active sites for the surface redox reactions. As a consequence, HFC Co3O4 as the supercapacitor electrode exhibits a superior rate capability, shows an excellent cycliability of 10,000 cycles at 10 A g(-1), and delivers large specific capacitances of 948.9 and 536.8 F g(-1) at 1 and 40 A g(-1), respectively. Catalytic studies of HFC Co3O4 for oxygen evolution reaction display a much higher turnover frequency of 1.67×10(-2) s(-1) in pH 14.0 KOH electrolyte at 400 mV overpotential and a lower Tafel slope of 70 mV dec(-1). HFC Co3O4 with the efficient electrochemical activity and good stability can remain a promising candidate for the electrochemical energy conversion and storage.

  17. Historia y filosofía de las ciencias en la educación polimodal: propuesta para su incorporación al aula History and philosophy of science in science curricula: a proposal for its incorporation in science classes

    Directory of Open Access Journals (Sweden)

    Verónica Guridi

    2004-12-01

    Full Text Available Durante los últimos años se viene enfatizando la necesidad de la incorporación de la Historia y Filosofía de las Ciencias (HFC, en adelante a los currículos de Ciencias. Mucho se ha avanzado respecto de la definición de los marcos teóricos que debieran orientar la incorporación de la HFC en la Enseñanza de las Ciencias, pero sin embargo son pocos los trabajos que muestran propuestas concretas de incorporación de la HFC en las clases de Ciencias. Este trabajo intenta realizar un aporte en el sentido antes mencionado, presentando una propuesta para el tratamiento de un núcleo temático específico correspondiente al primer año Polimodal (orientación Humanidades y Ciencias Sociales en el espacio curricular Físico - Química. El núcleo temático seleccionado corresponde al estudio de la evolución de los modelos atómicos (hasta el modelo atómico de Bohr.In the last few years the necessity of including History and Philosophy of Science (HFC, hereafter in Science Curricula has been emphasised. There have been important advances in theoretical frameworks, which should orient the incorporation of HFC into Science classes. However, there are only a few works that include proposals that show some ways of making this concrete. This work attempts to make a contribution in that direction, presenting a proposal for the treatment of a specific thematic nucleus of the curricular area "Physics-Chemistry". The proposal is designed for the first year of High School Education (with orientation in Humanities and Social Sciences. The selected content corresponds to the study of the evolution of atomic models (up to the model of Bohr.

  18. Electronegative LDL is linked to high-fat, high-cholesterol diet-induced nonalcoholic steatohepatitis in hamsters.

    Science.gov (United States)

    Lai, Yu-Sheng; Yang, Tzu-Ching; Chang, Po-Yuan; Chang, Shwu-Fen; Ho, Shu-Li; Chen, Hui-Ling; Lu, Shao-Chun

    2016-04-01

    The pathogenesis of nonalcoholic steatohepatitis (NASH), like that of atherosclerosis, involves lipid accumulation, inflammation and fibrosis. Recent studies suggest that oxidized LDL (oxLDL) may be a risk factor for NASH, but oxLDL levels were not directly measured in these studies. The aim of this study was to examine whether there was an association between electronegative LDL [LDL(-)], a mildly oxLDL found in the blood, and the development of NASH using two animal models. Golden Syrian hamsters and C57BL/6 mice were fed a high-fat, high-cholesterol (HFC) diet for 6 or 12weeks, then liver lipid and histopathology, plasma lipoprotein profile and LDL(-) levels were examined. The HFC-diet-fed hamsters and mice had similar levels of hepatic lipid but different histopathological changes, with microvesicular steatosis, hepatocellular hypertrophy, inflammation and bridging fibrosis in the hamsters, but only in mild steatohepatitis with low inflammatory cell infiltration in the mice. It also resulted in a significant increase in plasma levels of LDL cholesterol and LDL(-) in hamsters, but only a slight increase in mice. Moreover, enlarged Kupffer cells, LDL(-) and accumulation of unesterified cholesterol were detected in the portal area of HFC-diet-fed hamsters, but not HFC-diet-fed mice. An in vitro study showed that LDL(-) from HFC-diet-fed hamsters induced TNF-α secretion in rat Kupffer cell through a LOX-1-dependent pathway. Our results strongly suggest that LDL(-) is one of the underlying causes of hepatic inflammation and plays a critical role in the development of NASH. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. New Substrate-Guided Method of Predicting Slow Conducting Isthmuses of Ventricular Tachycardia: Preliminary Analysis to the Combined Use of Voltage Limit Adjustment and Fast-Fourier Transform Analysis.

    Science.gov (United States)

    Kuroki, Kenji; Nogami, Akihiko; Igarashi, Miyako; Masuda, Keita; Kowase, Shinya; Kurosaki, Kenji; Komatsu, Yuki; Naruse, Yoshihisa; Machino, Takeshi; Yamasaki, Hiro; Xu, Dongzhu; Murakoshi, Nobuyuki; Sekiguchi, Yukio; Aonuma, Kazutaka

    2018-04-01

    Several conducting channels of ventricular tachycardia (VT) can be identified using voltage limit adjustment (VLA) of substrate mapping. However, the sensitivity or specificity to predict a VT isthmus is not high by using VLA alone. This study aimed to evaluate the efficacy of the combined use of VLA and fast-Fourier transform analysis to predict VT isthmuses. VLA and fast-Fourier transform analyses of local ventricular bipolar electrograms during sinus rhythm were performed in 9 postinfarction patients who underwent catheter ablation for a total of 13 monomorphic VTs. Relatively higher voltage areas on an electroanatomical map were defined as high voltage channels (HVCs), and relatively higher fast-Fourier transform areas were defined as high-frequency channels (HFCs). HVCs were classified into full or partial HVCs (the entire or >30% of HVC can be detectable, respectively). Twelve full HVCs were identified in 7 of 9 patients. HFCs were located on 7 of 12 full HVCs. Five VT isthmuses (71%) were included in the 7 full HVC+/HFC+ sites, whereas no VT isthmus was found in the 5 full HVC+/HFC- sites. HFCs were identical to 9 of 16 partial HVCs. Eight VT isthmuses (89%) were included in the 9 partial HVC+/HFC+ sites, whereas no VT isthmus was found in the 7 partial HVC+/HFC- sites. All HVC+/HFC+ sites predicted VT isthmus with a sensitivity of 100% and a specificity of 80%. Combined use of VLA and fast-Fourier transform analysis may be a useful method to detect VT isthmuses. © 2018 American Heart Association, Inc.

  20. Dohsa Treatment to Improve Balance in Elderly People: An Evaluation of a Family-Based Rehabilitation Programme

    Directory of Open Access Journals (Sweden)

    Asghar Dadkhah

    2007-09-01

    Full Text Available Objectives: In this research we evaluate an individually family-based Dohsa exercise programme of balance in the aged people and its effect on self confidence for performing common daily tasks with less falling could be influenced by training. Methods: From a residential care center, five aged person were participated in this study. They were trained by Dohsa method for six weeks. Two types of Dohsa-hou were used: Relaxation and Tate-kei. Tate-kei was the task which required them to control their body vertically against gravity. Results: The results indicated that most of them had improved their balance and their confidence for doing their daily activities without falling in a better way. Discussion: The Dohsa family based rehabilitation program could improve their balance and increase their activity by not falling down. The family based programme can be a useful program for rehabilitation therapists in their therapy with aged people to improve their life skills and well beings.

  1. The heterogeneity of maid cafés: Exploring object-oriented fandom in Japan

    Directory of Open Access Journals (Sweden)

    Luke Sharp

    2014-06-01

    Full Text Available Maid cafés may be positioned as objects of (often oversimplified fan communities in Japan; their heterogeneous qualities may be explored by presenting chronotopes with which they may be reconsidered. The problematics of viewing maid cafés in a homogeneous or reductive way (via iyashi-kei, "relaxation purposes," and moe-kei, "entertainment purposes" are considered, and the results of empirical research conducted at establishments across Honshū in Japan are presented. The vast differences in the services and interactivities provided in maid café settings are at odds with the homogenized fashion in which these venues have been treated in the popular press, in local promotional publications, and often in the academic literature. By presenting chronotopes and case studies with which maid cafés may be reconsidered, what it means to discuss maid cafés as a holistic phenomenon is challenged, and a heuristic for examining how spaces are constructed inside such establishments is provided.

  2. Physical and chemical properties of artificial potting soils; Jinko jiban ryokuka baiyodo no butsuri kagakuteki seishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Kudo, T. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    Artificial potting soils are developed mostly for roof garden, and a lot of products are now on the market. However, these products have the merits and demerits. Therefore, Kajima Corporation developed 'Kei-soil' and 'Souka-meijin' to make up defects of the existing artificial potting soils, and 'Eco-eco K' using waste at a rate of 100% with consideration for environment. The paper considered what kinds of quality these artificial potting soil products developed have from physical/chemical viewpoints. As a result, the following were made clear: (1) the artificial potting soil has more excellent physical property than chernozem; (2) Since 'Aqua-soil,' '{alpha}-base 2,' 'Viva-soil' and 'Soilen G' do not include fertilizer content very much, the manuring practice in planting is important; (3) 'Kei-soil,' 'Souka-meijin' and 'Eco-eco K' include fertilizer content. (translated by NEDO)

  3. Analysis of seaweed marketing in warbal village, Southeast Maluku Regency, Indonesia

    Science.gov (United States)

    Tumiwa, Bruri B.; Renjaan, Meiskyana R.; B. A Somnaikubun, Glen; Betauubun, Kamilius D.; Hungan, Marselus

    2017-10-01

    Seaweed in Warbal Village, West Kei Kecil Subdistrict, Southeast Maluku Regency has prospects and business opportunities are adequate to give hope to farmers in improving welfare. The fact that seaweed farming has not yet provided better and maximum results as desired by the farmers. This study aims to evaluation the marketing channels, marketing margins and profit share of marketing agencies. The research is located in Warbal Village, West Kei Kecil Subdistrict, Southeast Maluku Regency which is determined purposively. The number of sample is 30 farmers taken by simple random sampling, 2 wholesaler traders and 2 collector traders taken by using snowball method. The data collection methods is interview and questionnaire directly to farmers and marketing agencies, literary method or data collector from institutions related to the research’s aims. The research results show that there is two marketing channel, as follows: Channel I: farmers, wholesaler traders, collector traders, PAP; Channel II: farmers, collector traders, PAP. The magnitude of marketing margins is different between the marketing channels, and so it is with profit share of a marketing agency. On channel I, magnitude margin is IDR 3,250 and profit share is 71.11% on farmers, 17.76% on wholesaler traders and 11.09% on collector traders. On channel II, the magnitude of marketing margin is IDR 1,250 and profit share is 88.88% on farmers and 11.09% to collector traders.

  4. Aqueous-stream uranium-removal technology cost/benefit and market analysis

    International Nuclear Information System (INIS)

    1994-03-01

    The primary purpose of this report is to present information that was gathered by Kapline Enterprises, Inc. (KEI) in order to help the Department of Energy (DOE) determine the merit of continued biosorption research funding. However, in the event that funding is continued, it is also intended to help the researchers in their efforts to develop a better uranium-removal process. This report (1) provides a comparison of DOE sites that may utilize aqueous-stream, uranium-removal biosorption technology, (2) presents a comparison of the biosorption and ion exchange processes, and (3) establishes performance criteria by which the project can be measured. It also attempts to provide focus for biosorbent ground-water-remediation research and to ask questions that need to be answered. This report is primarily a study of the US market for technologies that remove uranium from aqueous streams, but it also addresses the international market-particularly for Germany. Because KEI's access to international market information is extremely limited, the material presented in this report represents a best effort to obtain this data. Although uranium-contaminated aqueous streams are a problem in other countries as well, the scope of this report is primarily limited to the US and Germany for two reasons: (1) Germany is the country of the biosorbent-CRADA partner and (2) time constraints

  5. Development of optical sciences in Poland

    Science.gov (United States)

    Romaniuk, Ryszard S.

    2013-10-01

    Research and technical communities for optics, photonics and optoelectronics is grouped in this country in several organizations and institutions. These are: Photonics Society of Poland (PSP), Polish Committee of Optoelectronics of SEP, Photonics Section of KEiT PAN, Laser Club at WAT, and Optics Section of PTF. Each of these communities keeps slightly different specificity. PSP publishes a quarterly journal Photonics Letters of Poland, stimulates international cooperation, and organizes conferences during Industrial Fairs on Innovativeness. PKOpto SEP organizes didactic diploma competitions in optoelectronics. KEiT PAN takes patronage over national conferences in laser technology, optical fiber technology and communications, and photonics applications. SO-PTF has recently taken a decision to organize a cyclic event "Polish Optical Conference". The third edition of this conference PKO'2013 was held in Sandomierz on 30.06-04.07.2013. The conference scientific and technical topics include: quantum and nonlinear optics, photon physics, optic and technology of lasers and other sources of coherent radiation, optoelectronics, optical integrated circuits, optical fibers, medical optics, instrumental optics, optical spectroscopy, optical metrology, new optical materials, applications of optics, teaching in optics. This paper reviews chosen works presented during the III Polish Optical Conference (PKO'2013), representing the research efforts at different national institutions.

  6. Mapping Marine Resources Utilization Based on Seascapes Area: A Study on Gender Comparison

    Science.gov (United States)

    Picaulima, Simon; Teniwut, Wellem A.; Kahfi, Syahibul; M. K Teniwut, Roberto; Dewa Ayu Raka Susanti, Ida I.; Hungan, Marselus; Rahantoknam, Meyske; Hasyim, Cawalinya; Rahakbauw, Siska D.; Renjaan, M. R.; Ngabalin, Anna M.; Ngangun, Tati A.; Pentury, Frischila; Betaubun, K. D.; Ngamel, A. K.; Ohoiwutun, E. C.

    2017-10-01

    Each section of coastal area from village area to deep sea has particular fisheries and marine activities. Therefore requirements for knowledge, skill, and risk are distinct between each scape. Based on this notion we divided seascapes based on three different area, first is village area to mangrove and coconut trees before coast area, second is area from beach to shallow water and the third is deep sea. We conducted our data collection in Kei Islands, Indonesia, with purposive sampling to target fishermen and aquaculture farmers in the coastal area. Purposes of this research are to analyze the role and the contribution of male and female on each area to formulate the best way to improve and maintain the sustainability of microenterprises and coastal community welfare; we used logistic regression to analyze the data. The result demonstrated each fisheries activity in each seascape with based on gender on each area and activity. Recommendation of this study especially for the government as empirical guidance to improve the economic welfare of the coastal community in Kei Islands and small islands area in general.

  7. A new nordic structure evaluation system for diets fed to dairy cows

    DEFF Research Database (Denmark)

    Nørgaard, Peder; Nadeau, E.; Randby, Å.T.

    2010-01-01

    , and with studies as random effect for ruminating time. The mRTf value per kg forage NDF decreased at increased BW and DNFIf/BW. The mETf value increased at increasing BW and at decreasing DM contents of grass silage. Intake of NDF from rolled barley stimulated ruminating time by 3/4 of the stimuli from DNFIf......The overall aim was to establish a model for predicting chewing index (CI) values for ranking the fibrousnesses of feeds fed to dairy cows within the Nordic Chewing index system. The CI values are predicted as the sum of the eating (EI) and ruminating time index (RI) values. The EI values...... are assumed to be proportional with the NDF content and a particle size factor through the porportionality factor kEI. The RI values are assumed to be proportional with the NDF content, a particle size factor and a hardness factor through the proportionality factor kRI. The kEI, kRI values and the k...

  8. Studies of bone marrow scintigrams with sup(99m)technetium sulfur colloid on various hematological disorders

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, Takashi (Hiroshima Univ. (Japan). Research Inst. for Nuclear Medicine and Biology)

    1984-02-01

    One hundred and eighty-five bone marrow scintigraphy on the whole body was performed on eight healthy adults and 151 patients with various hematologic diseases including 64 leukemia, 41 anemia, 23 other malignancy, etc. The positions of the investigated bone marrow were divided into the central marrow (five positions on the trunk bones) and the peripheral marrow (11 positions on the upper and 11 positions on the lower extremities) on the scintigram. The bone marrow scintigram was estimated by following three criteria. The first, ''Yuu-ryoiki'' (positive area), was the existence of sup(99m)Tc sulfur colloid accumulation on bone marrow (two grades; presence or absence). The second, ''Bunpu-kei'' (distribution form), was the extent of the sup(99m)Tc accumulation area of the investigated bone marrow and was divided into five grades. The last, ''Kido'' (intensity of radioactivity), was the density of the sup(99m)Tc accumulation on the area and was divided into five grades. Using this estimation, in the diseases with bone marrow hyperplasia such as Primary Thrombocythemia and Hemolytic Anemia, ''Yuu-ryoiki'' was enlarged, ''Bunpu-kei'' was extended, and ''Kido'' was increased comparing with those in healthy adult. In contrast, in the diseases with bone marrow hypoplasia such as Myelofibrosis and Aplastic Anemia, ''Yuu-ryoiki'' was reduced, ''Bunpu-kei'' was contracted, and ''Kido'' was decreased. However, the enlargement of ''Yuu-ryoiki'' did not always mean bone marrow hyperplasia. The author could evaluate not only the range and distribution of hemopoiesis as a whole in malignant or benign diseases but also the residual effective hemopoiesis to know the suitable time of the initiation of the therapy or to predict the prognosis of these cases. In this study it was shown

  9. Venezuelan contribution to the ozone layer preservation

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, M.H.; Coltters, R.; Damian, A. [Universidad La Urbina, Caracas (Venezuela). Escuela de Ingenieria Mecanica

    1995-12-31

    There are two ways to solve the problem of the ozone layer destruction in the upper atmosphere by the harmful chlorine which comes from CFC refrigerants and from aerosols. The first one is to replace the old equipment by new ones which work with non-contaminant refrigerants and the second solution is to establish a conversion program according to the Montreal Protocol and the Vienna Convention. According to this, some Venezuelan Companies are beginning to replace the car`s air conditioning equipment, and others like CVG-SIDOR are making an accelerated program for its central air conditioning system. Another company, C.A. Metro de Caracas, has made a progressive program for the replacement of Freon R-11 and R-12 for HFC 123 and HFC-134a respectively. The results indicate that the most economical solution is to replace these refrigerants instead of replacing the equipment completely.

  10. Mining and global environmental challenges

    Energy Technology Data Exchange (ETDEWEB)

    Greeff, J C; Bailey-McEwan, M [Chamber of Mines of South Africa, Johannesburg (South Africa)

    1992-04-01

    At least half of South Africa's gold production is presently dependent on CFC11 an CFC12 as refrigerants in water chilling machines used in cooling the underground workings. The South African Government will ratify the revised Montreal Protocol on substances that deplete the ozone layer which will mean CFCs will have to be phased out probably by 1997. HFC134 or HFC22 are possible replacements for CFC but present costs of converting machines are high. The article goes on to discuss the contribution of CFCs and CO{sub 2} to global warming and model simulations and predictions of climate change. Likely effects of growing concern about global warming on the coal mining industry are the possible limitations on the use of coal and the increased need for clean coal technology. 12 refs., 5 figs., 3 tabs.

  11. A binary mixture operated heat pump

    International Nuclear Information System (INIS)

    Hihara, E.; Saito, T.

    1991-01-01

    This paper evaluates the performance of possible binary mixtures as working fluids in high- temperature heat pump applications. The binary mixtures, which are potential alternatives of fully halogenated hydrocarbons, include HCFC142b/HCFC22, HFC152a/HCFC22, HFC134a/HCFC22. The performance of the mixtures is estimated by a thermodynamic model and a practical model in which the heat transfer is considered in heat exchangers. One of the advantages of binary mixtures is a higher coefficient of performance, which is caused by the small temperature difference between the heat-sink/-source fluid and the refrigerant. The mixture HCFC142b/HCFC22 is promising from the stand point of thermodynamic performance

  12. Low-temperature anomalies of photoinduced second harmonic generation in skutterudites

    International Nuclear Information System (INIS)

    Viennois, R; Kityk, I V; Terki, F; Charar, S; Muntzer, A; Kasperczyk, J; Ravot, D; Tedenac, J C

    2003-01-01

    Photoinduced second harmonic generation (PISHG) was found in skutterudite compounds of CeFe 4 Sb 12 and Ce 0.7 Fe 3.5 Ni 0.5 Sb 12 . Measurements versus temperature, pump-probe delaying time and external magnetic field were performed. The studied compounds belong to moderate heavy fermion compounds (HFC) in the ground state. The PISHG signals appear at 6.8 and 4.9 K for CeFe 4 Sb 12 and Ce 0.7 Fe 3.5 Ni 0.5 Sb 12 , respectively. We suspect that these signals are due to anharmonic electron-phonon interactions creating a charge density non-centrosymmetry. The observed effects are caused either by a possible phase transition or by drastic changes in the electron structure of the HFC with decreasing temperature

  13. The sectoral trends of multigas emissions inventory of India

    DEFF Research Database (Denmark)

    Garg, A.; Shukla, P.R.; Kapshe, M.

    2006-01-01

    This paper provides the trends of greenhouse gas (GHG) and local air pollutant emissions of India for 1985-2005. The GHGs covered are six Kyoto gases, namely carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), perfluorocarbons (PFCs), hydrofluorocarbons (HFCs) and sulfur hexafluoride (SF6...... in the same sector is the major source of N2O emissions. PFC emissions are dominated by C2F6 and CF4 emissions from aluminum production. The majority of HFC emissions are contributed by HFC-23, a by-product during the production of HCFC-22 that is widely used in refrigeration industry. CO emissions have...... dominance from biomass burning. Particulate emissions are dominated by biomass burning (residential sector), road transport and coal combustion in large plants. These varied emission patterns provide interesting policy links and disjoints, such as-which and where mitigation flexibility for the Kyoto gases...

  14. Release and attenuation of fluorocarbons in landfills

    DEFF Research Database (Denmark)

    Kjeldsen, Peter; Scheutz, Charlotte

    2003-01-01

    Several halocarbons with very high global warming and ozone depleting potentials have been used as blowing agent for insulation foam in refrigerators and freezers. Many appliances are shredded after the end of their useful life. Release experiments carried out in the laboratory on insulation foam...... blown with CFC-11, HCFC-141b, HFC- 134a, and HFC-245fa revealed that most of the blowing agent is not released to the atmosphere during a six-week period following the shredding process. The fraction which is released in the six-week period is highly dependent on how fine the foam is shredded....... The residual blowing agent remaining after the six-week period may be very slowly released if the integrity of the foam particles with respect to diffusional properties is kept after disposal of the foam waste in landfills. Laboratory experiments simulating attenuation processes in the landfilled waste...

  15. Modified Peng-Robinson Equation of State for Pure and Mixture Refrigerants with R-32,R-125 and R-134a

    Science.gov (United States)

    Ll, Jin; Sato, Haruki; Watanabe, Koichi

    On the basis of critically-evaluated thermodynamic property data among those recently published, a new Peng-Robinson equation of state for the HFC refrigerants,R-32,R-125 and R-134a,has be end eveloped so as to represent the VLE properties in the vapor-liquid coexisting phase at temperatures 223K-323K. In accord with a challenge to correlate the binary and/or ternary interatction parameters as functions of temperature, we have also applied the present modified Peng-Robinson equation of state to the promising alternative HFC refrigerant mixtures, i.e., R-32/125,R-32/134a and R-32/125/134a systems. The developed equation of state improves significantly its effectiveness for practical engineering property calculations at refrigerantion and air-conditioning industries in comparison with conventional Peng-Robinson equation.

  16. Analysis of Human Errors in Japanese Nuclear Power Plants using JHPES/JAESS

    International Nuclear Information System (INIS)

    Kojima, Mitsuhiro; Mimura, Masahiro; Yamaguchi, Osamu

    1998-01-01

    CRIEPI (Central Research Institute for Electric Power Industries) / HFC (Human Factors research Center) developed J-HPES (Japanese version of Human Performance Enhancement System) based on the HPES which was originally developed by INPO to analyze events resulted from human errors. J-HPES was systematized into a computer program named JAESS (J-HPES Analysis and Evaluation Support System) and both systems were distributed to all Japanese electric power companies to analyze events by themselves. CRIEPI / HFC also analyzed the incidents in Japanese nuclear power plants (NPPs) which were officially reported and identified as human error related with J-HPES / JAESS. These incidents have numbered up to 188 cases over the last 30 years. An outline of this analysis is given, and some preliminary findings are shown. (authors)

  17. Field and sample history dependence of the compensation temperature in Sm0.97Gd0.03Al2

    International Nuclear Information System (INIS)

    Vaidya, U.V.; Rakhecha, V.C.; Sumithra, S.; Ramakrishnan, S.; Grover, A.K.

    2007-01-01

    We present magnetization data on three polycrystalline specimens of Sm 0.97 Gd 0.03 Al 2 : (1) as-cast (grainy texture), (2) powder, and (3) re-melted fast-quenched (plate). The data are presented for nominally zero- (ZFC) and high-field-cooling (HFC) histories. A zero cross-over in magnetization curve at some temperature T=T 0 was seen in ZFC data on grainy and powder samples, but not in the plate sample. At fields surpassing magnetocrystalline anisotropy, a 4f magnetic moment flip was still evidenced by HFC data in all samples at a compensation temperature T comp , which must necessarily be treated as distinct from T 0 (T 0 may not even exist). Proper understanding of T comp should take account of thermomagnetic history effects

  18. Insertion of historical and philosophical components in disciplines of the natural sciences in the medium teaching: reflections from the historiographies controversies among Kuhn and Lakatos

    Directory of Open Access Journals (Sweden)

    Osmar Henrique Moura da Silv

    2010-12-01

    Full Text Available The incorporation of historical and philosophical elements in disciplines of natural sciences of the high school has been reaching defended in the specific literature and critics improved visions concerning the use of the History and Philosophy of the Science (HFC for didactic ends. In that sense, the discussions are important since ponder influences in the orientation of curricula of significant portion of the undergraduate teaching. Worrying about such discussions, this study put reflections about de historiographies controversies among Kuhn and Lakatos whose educational implications allow support to a tendency of the use of HFC as resources not to obtain completely authentic historical reconstructions, but to favor intentions of to develop and to project didactic solutions in that the pedagogy doesn't need to submit itself to the History.

  19. Denmark's national inventory report 2008 - Submitted under the United Nations framework convention on climate change, 1990-2006. Emission inventories

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, Ole-Kenneth; Lyck, E; Hjorth Mikkelsen, M [and others

    2008-05-15

    This report is Denmark's National Inventory Report reported to the Conference of the Parties under the United Nations Framework Convention on Climate Change (UNFCCC) due by 15 April 2008. The report contains information on Denmark's inventories for all years' from 1990 to 2006 for CO{sub 2}, CH{sub 4}, N{sub 2}O, HFC{sub s}, PFC{sub s} and SF{sub 6}, CO, NMVOC, SO{sub 2}. (au)

  20. A Novel Evolutionary Engineering Design Approach for Mixed-Domain Systems

    DEFF Research Database (Denmark)

    Fan, Zhun; Hu, J.; Seo, K.

    2004-01-01

    This paper presents an approach to engineering design of mixed-domain dynamic systems. The approach aims at system-level design and has two key features: first, it generates engineering designs that satisfy predefined specifications in an automatic manner; second, it can design systems belonging ...... often encountered in evolutionary computation, a HFC (Hierarchical Fair Competition) model is adopted in this work. Examples of an analog filter design and a MEM filter design illustrate the application of the approach....

  1. Evaporation of new refrigerants on tube with improved surfaces. Final report. Appendices: A, B, C, D, E and F; Evaporation de nouveaux refrigerants sur des tubes a surface amelioree. Rapport final. Annexes: A, B, C, D, E et F

    Energy Technology Data Exchange (ETDEWEB)

    Kattan, N.; Favrat, D.; Thome, J. R.; Nidegger, E.; Zuercher, O. [Ecole Polytechnique Federale, Lab. d` Energetique Industrielle (LENI), Lausanne (Switzerland)

    1995-07-15

    The substitution of old refrigerants in refrigeration systems, heat pumps and organic Rankine cycles for heat recovery, request a good knowledge of heat transfer properties of substitute fluids. The test measurements in LENI test facility (concentric tubes with water flowing in a counter-current flow) with new refrigerants like HFC134a, HCFC123, R-402A, have established a new data bank with new refrigerants, a comparison with old refrigerants like CFC11, CFC12 CFC/HCFC502 and with existent correlations. Correlations were programmed to calculate and compare heat transfer coefficient during the tests. To develop a new correlation based on flow regimes, a high speed Sony video tape camera is used to observe and identify flow patterns. Important images are captured, digitalized, stored for later analysis and sent to a color plotter. Several flow pattern maps were programmed and compared to flow regimes observed on the test rig. Local flow boiling heat transfer coefficients were measured for HFC134a and HCFC123 evaporating inside a microfin tube. In addition, microheat transfer augmentation relative to plain tube test data was investigated. The presence of oil in the evaporator has an effect on heat transfer coefficient. Local flow boiling heat transfer coefficients were measured for refrigerant HFC134a-oil ester (Mobil EAL Arctic 68). A new thermodynamic approach for modeling mixtures of refrigerants and lubricating oils is developed. A very high accuracy, straight vibrating tube type of density flowmeter is used to measure oil concentrations of flowing HFC134a-oil mixtures. (author) figs., tabs., refs.

  2. Evaporation of new refrigerants on tubes with improved surfaces; Evaporation de nouveaux refrigerants sur des tubes a surface amelioree

    Energy Technology Data Exchange (ETDEWEB)

    Kattan, N.; Favrat, D.; Thome, J. R.; Nidegger, E.; Zuercher, O. [Ecole Polytechnique Federale, Lab. d` Energetique Industrielle (LENI), Lausanne (Switzerland)

    1995-07-15

    The substitution of old refrigerants in refrigeration systems, heat pumps and organic Rankine cycles for heat recovery, request a good knowledge of heat transfer properties of substitute fluids. The test measurements in LENI test facility (concentric tubes with water flowing in a counter-current flow) with new refrigerants like HFC134a, HCFC123, R-404A, R-402A, have established a new data bank with new refrigerants, a comparison with old refrigerants like CFC11, CFC12 CFC/HCFC502 and with existent correlations. Correlations were programmed to calculate and compare heat transfer coefficient during the tests. To develop a new correlation based on flow regimes, a high speed Sony video tape camera is used to observe and identify flow patterns. Important images are captured, digitalized, stored for later analysis and sent to a color plotter. Several flow pattern maps were programmed and compared to flow regimes observed on the test rig. Local flow boiling heat transfer coefficients were measured for HFC134a and HCFC123 evaporating inside a microfin tube. In addition, microfin heat transfer augmentation relative to plain tube test data was investigated. The presence of oil in the evaporator has an effect on heat transfer coefficient. Local flow boiling heat transfer coefficients were measured for refrigerant HFC134a-oil ester (Mobil EAL Arctic 68). A new thermodynamic approach for modeling mixtures of refrigerants and lubricating oils is developed. A very high accuracy, straight vibrating tube type of density flowmeter is used to measure oil concentrations of flowing HFC134a-oil mixtures. (author) 28 figs., 25 refs.

  3. Influence of GSTM1 and GSTT1 genotypes and confounding factors on the frequency of sister chromatid exchange and micronucleus among road construction workers.

    Science.gov (United States)

    Kumar, Anil; Yadav, Anita; Giri, Shiv Kumar; Dev, Kapil; Gautam, Sanjeev Kumar; Gupta, Ranjan; Aggarwal, Neeraj

    2011-07-01

    In the present study, we have investigated the influence of polymorphism of GSTM1 and GSTT1 genes and confounding factors such as age, sex, exposure duration and consumption habits on cytogenetic biomarkers. Frequency of sister chromatid exchanges (SCEs), high frequency cell (HFC) and cytokinesis blocked micronuclei (CBMN) were evaluated in peripheral blood lymphocytes of 115 occupationally exposed road construction workers and 105 unexposed individuals. The distribution of null and positive genotypes of glutathione-S transferase gene was evaluated by multiplex PCR among control and exposed subjects. An increased frequency of CBMN (7.03±2.08); SCE (6.95±1.76) and HFC (6.28±1.69) were found in exposed subjects when compared to referent (CBMN - 3.35±1.10; SCE - 4.13±1.30 and HFC - 3.98±1.56). These results were found statistically significant at p<0.05. When the effect of confounding factors on the frequency of studied biomarkers was evaluated, a strong positive interaction was found. The individuals having GSTM1 and GSTT1 null genotypes had higher frequency of CBMN, SCE and HFC. The association between GSTM1 and GSTT1 genotypes and studied biomarkers was found statistically significant at p<0.05. Our findings suggest that individuals having null type of GST are more susceptible to cytogenetic damage by occupational exposure regardless of confounding factors. There is a significant effect of polymorphism of these genes on cytogenetic biomarkers which are considered as early effects of genotoxic carcinogens. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. International research into chlorofluorocarbon (CFC) alternatives

    Energy Technology Data Exchange (ETDEWEB)

    Marseille, T.J.; Shankle, D.L.; Thurman, A.G.

    1992-05-01

    Selected researchers from 21 countries were queried through questionnaires about their current and planned research activities. The results of the survey show that the majority of research being conducted by the respondents is devoted to investigating the hydrogenated fluorocarbon HFC-134a as a replacement for CFC-12 in refrigeration applications. The main issue with this alternative is identifying compatible lubricants that do not reduce its effectiveness.

  5. New botanical drug, HL tablet, reduces hepatic fat as measured by magnetic resonance spectroscopy in patients with nonalcoholic fatty liver disease: A placebo-controlled, randomized, phase II trial.

    Science.gov (United States)

    Jeong, Jae Yoon; Sohn, Joo Hyun; Baek, Yang Hyun; Cho, Yong Kyun; Kim, Yongsoo; Kim, Hyeonjin

    2017-08-28

    To evaluate the efficacy and safety of HL tablet extracted from magnolia officinalis for treating patients with nonalcoholic fatty liver disease (NAFLD). Seventy-four patients with NAFLD diagnosed by ultrasonography were randomly assigned to 3 groups given high dose (400 mg) HL tablet, low dose (133.4 mg) HL tablet and placebo, respectively, daily for 12 wk. The primary endpoint was post-treatment change of hepatic fat content (HFC) measured by magnetic resonance spectroscopy. Secondary endpoints included changes of serum aspartate aminotransferase, alanine aminotransferase (ALT), cholesterol, triglyceride, free fatty acid, homeostasis model assessment-estimated insulin resistance, and body mass index (BMI). The mean HFC of the high dose HL group, but not of the low dose group, declined significantly after 12 wk of treatment (high dose vs placebo, P = 0.033; low dose vs placebo, P = 0.386). The mean changes of HFC from baseline at week 12 were -1.7% ± 3.1% in the high dose group ( P = 0.018), -1.21% ± 4.97% in the low dose group ( P = 0.254) and 0.61% ± 3.87% in the placebo group (relative changes compared to baseline, high dose were: -12.1% ± 23.5%, low dose: -3.2% ± 32.0%, and placebo: 7.6% ± 44.0%). Serum ALT levels also tended to decrease in the groups receiving HL tablet while other factors were unaffected. There were no moderate or severe treatment-related safety issues during the study. HL tablet is effective in reducing HFC without any negative lipid profiles, BMI changes and adverse effects.

  6. Social accountability in primary health care in West and Central Africa: exploring the role of health facility committees.

    Science.gov (United States)

    Lodenstein, Elsbet; Mafuta, Eric; Kpatchavi, Adolphe C; Servais, Jean; Dieleman, Marjolein; Broerse, Jacqueline E W; Barry, Alpha Amadou Bano; Mambu, Thérèse M N; Toonen, Jurrien

    2017-06-13

    Social accountability has been emphasised as an important strategy to increase the quality, equity, and responsiveness of health services. In many countries, health facility committees (HFCs) provide the accountability interface between health providers and citizens or users of health services. This article explores the social accountability practices facilitated by HFCs in Benin, Guinea and the Democratic Republic of Congo. The paper is based on a cross-case comparison of 11 HFCs across the three countries. The HFCs were purposefully selected based on the (past) presence of community participation support programs. The cases were derived from qualitative research involving document analysis as well as interviews and focus group discussions with health workers, citizens, committee members, and local authorities. Most HFCs facilitate social accountability by engaging with health providers in person or through meetings to discuss service failures, leading to changes in the quality of services, such as improved health worker presence, the availability of night shifts, the display of drug prices and replacement of poorly functioning health workers. Social accountability practices are however often individualised and not systematic, and their success depends on HFC leadership and synergy with other community structures. The absence of remuneration for HFC members does not seem to affect HFC engagement in social accountability. Most HFCs in this study offer a social accountability forum, but the informal and non-systematic character and limited community consultation leave opportunities for the exclusion of voices of marginalised groups. More inclusive, coherent and authoritative social accountability practices can be developed by making explicit the mandate of HFC in the planning, monitoring, and supervision of health services; providing instruments for organising local accountability processes; strengthening opportunities for community input and feedback; and

  7. Rate constants for the gas-phase reactions of OH radicals with CH3CHF2 and CHCl2CF3 over the temperature range 295-388 K

    DEFF Research Database (Denmark)

    Nielsen, O.J.

    1991-01-01

    be fit to the Arrhenius expressions: k(OH + HFC-152a) = 3.9 X 10(-12) exp[(-1370 +/- 260)/T] cm3 molecule-1 s-1 and k(OH + HCFC-123) = 1.1 X 10(-12) X exp[(-940 +/- 200)/T] cm3 molecule-1 s-1. The results are compared to the available literature data and discussed in terms of reactivity trends...

  8. Public Role and Engagement in Counterterrorism Efforts: Implications of Israeli Practices for the U.S.

    Science.gov (United States)

    2009-04-02

    radiation exposure to the thyroid gland helping prevent thyroid cancer during a radiological event. The NRC has provided potassium iodide tablets to...Israeli public to tune into Galatz for information during an emergency. After the Second Lebanon War of 2006, HFC established a “ silent ” radio...station. Three FM stations broadcast continuously throughout the day but remain silent , with nothing being broadcast over the airwaves. In the event of an

  9. Experimental Performance Investigation of New Low-GWP Refrigerants for Use in Two-Phase Evaporative Cooling of Electronics

    OpenAIRE

    Nicolette-Baker, Alexis; Garr, Elizabeth; Sathe, Abhijit; O'Shaughnessey, Steve

    2014-01-01

    With growing global warning concerns on the current breed of HFC refrigerants, a search for more environmentally-friendly fluids has already begun. Potential alternatives to replace R134a should have significantly lower global warming potential (GWP), operate at similar system pressures, and maintain all other advantages of R134a (non-flammability, dielectric properties, etc.). This study investigates four possible alternatives that have been identified by AHRI in its Low-GWP Alternative Refr...

  10. Application of the Backward-Smoothing Extended Kalman Filter to Attitude Estimation and Prediction using Radar Observations

    Science.gov (United States)

    2009-06-01

    Pressure (R) Figure 2.9 Aerodynamic drag acting at the centroid of each surface element This approach avoids time- consuming repetitive evaluation of...5. Update the state estimate with the latest measurement yfe (37 p. 210) xfe(tfc) = **_!&) + Kfc (yfe - hfc) (3.72) In some cases it is necessary to...in XELIAS can be a rather challenging and time consuming task, depending on the complexity of the target being analyzed. 4. According to the XELIAS

  11. Alternative Refrigerant Evaluation for High-Ambient Temperature Environments: R-22 and R-410A Alternatives for Mini-Split Air Conditioners

    Energy Technology Data Exchange (ETDEWEB)

    Abdelaziz, Omar [ORNL; Munk, Jeffrey D [ORNL; Shrestha, Som S [ORNL; Linkous, Randall Lee [ORNL; Goetzler, William [Navigant Consulting Inc.; Guernsey, Matt [Navigant Consulting Inc.; Kassuga, Theo [Navigant Consulting Inc.

    2015-08-01

    The Oak Ridge National Laboratory (ORNL) High-Ambient Temperature Testing Program for Low-GWP Refrigerants aims to develop an understanding of the performance of low-Global Warming Potential (low-GWP) alternatives to Hydrochlorofluorocarbon (HCFC) and Hydrofluorocarbon (HFC) refrigerants in mini-split air conditioners under high ambient temperature conditions. This interim working paper describes the parties involved, the alternative refrigerants selection process, the test procedures, and the preliminary results.

  12. Experimental Results For Hydrocarbon Refrigerant Vaporization In Brazed Plate Heat Exchangers at High Pressure

    OpenAIRE

    Desideri, Adriano; Schmidt Ommen, Torben; Wronski, Jorrit; Quoilin, Sylvain; Lemort, Vincent; Haglind, Fredrik

    2016-01-01

    In this contribution, the experimental heat transfer coefficient  and the pressure drop measured during HFC refrigerants vaporization inside small brazed plate heat exchanger (PHE) at typical evaporation temperature for organic Rankine cycle systems for low thermal energy quality applications are presented. Scientific work focusing on the heat transfer in PHEs has been carried out since the late 19th century. More recent publications have been focusing on vaporization and condensation of ref...

  13. Carbon Dioxide as Secondary Refrigerant in Supermarkets

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard

    Resume I forbindelse med udfasning af HCFC- og HFC-kølemidlerne er opstået stor interesse for anvendelse af naturlige kølemidler samt indirekte køling i forbindelse med køling i supermarkeder. Som sekundært kølemiddel med faseskift kan kuldioxid anvendes. I supermarkeder med køleanlægget placeret...

  14. Development of a Refractory High Entropy Superalloy (Postprint)

    Science.gov (United States)

    2016-03-17

    hardened with HfC precipitates [2], Co-Re- or Co-Al-W-based alloys [3] or two-phase ( FCC + L12) refractory superalloys based on platinum group metals...Ni-based superalloys consisting of cuboids with the ordered L12 structure embedded in an FCC solid-solution matrix. Based on this microstructural...and 5). A comparison of the average atomic radii with the measured lattice parameters allows us to conclude that the disordered BCC phase forming

  15. Alternative Refrigerant Evaluation for High-Ambient-Temperature Environments: R-22 and R-410A Alternatives for Rooftop Air Conditioners

    Energy Technology Data Exchange (ETDEWEB)

    Abdelaziz, Omar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shrestha, Som S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shen, Bo [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linkous, Randall Lee [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Goetzler, William [Navigant Consulting Inc., Burlington, MA (United States); Guernsey, Matt [Navigant Consulting Inc., Burlington, MA (United States); Bargach, Youssef [Navigant Consulting Inc., Burlington, MA (United States)

    2016-09-01

    The Oak Ridge National Laboratory (ORNL) High-Ambient-Temperature Evaluation Program for Low-Global Warming Potential (Low-GWP) Refrigerants aims to develop an understanding of the performance of low-GWP alternative refrigerants relative to hydrochlorofluorocarbon (HCFC) and hydrofluorocarbon (HFC) refrigerants in packaged or Rooftop Unit (RTU) air conditioners under high-ambient-temperature conditions. This final report describes the parties involved, the alternative refrigerants selection process, the test procedures, and the final results.

  16. Alternative Refrigerant Evaluation for High-Ambient-Temperature Environments: R-22 and R-410A Alternatives for Mini-Split Air Conditioners

    Energy Technology Data Exchange (ETDEWEB)

    Abdelaziz, Omar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shrestha, Som S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Munk, Jeffrey D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linkous, Randall Lee [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Goetzler, William [Navigant Consulting Inc., Burlington, MA (United States); Guernsey, Matt [Navigant Consulting Inc., Burlington, MA (United States); Kassuga, Theo [Navigant Consulting Inc., Burlington, MA (United States)

    2015-10-01

    The Oak Ridge National Laboratory (ORNL) High-Ambient-Temperature Evaluation Program for low– global warming potential (Low-GWP) Refrigerants aims to develop an understanding of the performance of low-GWP alternative refrigerants to hydrochlorofluorocarbon (HCFC) and hydrofluorocarbon (HFC) refrigerants in mini-split air conditioners under high-ambient-temperature conditions. This final report describes the parties involved, the alternative refrigerant selection process, the test procedures, and the final results.

  17. Greenhouse effect: an issue for the refrigeration and air conditioning sector; Effet de serre: quelle problematique pour le froid et le conditionnement de l`air?

    Energy Technology Data Exchange (ETDEWEB)

    Billiard, F. [Institut International du Froid, 75 - Paris (France)

    1997-12-31

    The principles of greenhouse effect and the greenhouse gas main direct and indirect emission sources due to refrigeration and air conditioning systems are first reviewed. Evolution scenarios from 1992 to 2020 and 2100 for the emissions of CFC, HCFC and HFC are presented and related to the Kyoto protocol project limitations; technical improvements in refrigerating and air conditioning systems (lower refrigerant utilization, fluid confinement, alternative technologies, natural refrigerant utilization, etc.) could lead to substantial diminutions of these greenhouse gases

  18. Substitutes for potent green house gases. HFCs, PFCs and SF{sub 6}. Status report

    Energy Technology Data Exchange (ETDEWEB)

    Pedersen, P.H. [Dansk Teknologisk Institut (Denmark)

    1997-12-31

    CFCs (halogenated chlorofluorocarbons), HCFCs (hydrochlorofluorocarbons), HFCs (hydrofluorocarbons), PFCs (fluorocarbons) and SF{sub 6} (sulphur hexafluoride) are all artificial substances which were not to be found in nature until recently. In 1995 the Danish consumption of HFC substances was approximately 740 tonnes, where the corresponding amount of SF{sub 6} was about 17 tonnes. If the entire amount of these substances was released to to the atmosphere, the resulting impact would correspond to an increased emission of greenhouse gases, corresponding to approximately 1.5 million tonnes of CO{sub 2}. HFC substances would account for 73%, SF{sub 6} with 25% and PFC for 1%. This corresponds to approximately 2.6% of the Danish CO{sub 2} emission (nearly 60 million tonnes per year). This corresponds to about half of the aimed 6% reduction of CO{sub 2} emission attained by introduction of mandatory green taxes on CO{sub 2}. According to experience from the CFC programme it is possible to recover some CFC and send it to controlled destruction. From 1993 to 1996 the refrigeration industry, for instance, has returned a total amount of 163 tonnes of CFC refrigerant through the KMO organization (Koelebranchens Miljoe Ordning). Most of this has been destroyed and a small amount has been purified and recycled afterwards. Similarly, it is likely to believe that some HFC refrigerant will be returned through the KMO organization. (au) 11 refs., also published in Danish

  19. Hydrocarbons as Refrigerants―A Review

    Directory of Open Access Journals (Sweden)

    J. H. KOH

    2017-08-01

    Full Text Available Refrigerants used in air conditioning and refrigeration (AC&R indusries have come full circle since the beginning of the industrialrevolution. With concern on issues relating to the environment such as the global warming and climate change issues, we should finda better alternative than to continue using these refrigerants that cause global warming and ozone depletion. AC&R industryplayers have blended in by introducing some new equipment and components that are specificallydesigned for hydrocarbon (HC use. Mostnew refrigerators sold in Malaysia are already equipped with isobutane [a hydrocarbon designated as R-600a by the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE standards]as refrigerants. Malaysia has ratifiedthe Montreal Protocol and targetted a 10% reduction in hydrochlorofluorocarbon(HCFC consumption, beginning 2016 with the banning of 2.5 horsepower (hp and below in air-conditioning (AC equipment to be used. Instead,hydrofluorocarbon(HFC R-410a was introduced as a replacement for HCFC- 22, whereas in other countries this HFC has been phased down. This article was initiated  because of the difficultin findinga replacement for HCFC. Also, the possibilities of using HC as an alternative to replace HCFC insteadof using HFC as a transitional refrigerant in place of HCFC is reviewed in this article. The performance of HC is very similar to HCFC and flmmability issues could be easily overcome with the use of an effectivedesign. Their use could be facilitated with the adaptation of specific standards and properly enacted legislatio

  20. Haptic-Multimodal Flight Control System Update

    Science.gov (United States)

    Goodrich, Kenneth H.; Schutte, Paul C.; Williams, Ralph A.

    2011-01-01

    The rapidly advancing capabilities of autonomous aircraft suggest a future where many of the responsibilities of today s pilot transition to the vehicle, transforming the pilot s job into something akin to driving a car or simply being a passenger. Notionally, this transition will reduce the specialized skills, training, and attention required of the human user while improving safety and performance. However, our experience with highly automated aircraft highlights many challenges to this transition including: lack of automation resilience; adverse human-automation interaction under stress; and the difficulty of developing certification standards and methods of compliance for complex systems performing critical functions traditionally performed by the pilot (e.g., sense and avoid vs. see and avoid). Recognizing these opportunities and realities, researchers at NASA Langley are developing a haptic-multimodal flight control (HFC) system concept that can serve as a bridge between today s state of the art aircraft that are highly automated but have little autonomy and can only be operated safely by highly trained experts (i.e., pilots) to a future in which non-experts (e.g., drivers) can safely and reliably use autonomous aircraft to perform a variety of missions. This paper reviews the motivation and theoretical basis of the HFC system, describes its current state of development, and presents results from two pilot-in-the-loop simulation studies. These preliminary studies suggest the HFC reshapes human-automation interaction in a way well-suited to revolutionary ease-of-use.

  1. High-global warming potential F-gas emissions in California: comparison of ambient-based versus inventory-based emission estimates, and implications of refined estimates.

    Science.gov (United States)

    Gallagher, Glenn; Zhan, Tao; Hsu, Ying-Kuang; Gupta, Pamela; Pederson, James; Croes, Bart; Blake, Donald R; Barletta, Barbara; Meinardi, Simone; Ashford, Paul; Vetter, Arnie; Saba, Sabine; Slim, Rayan; Palandre, Lionel; Clodic, Denis; Mathis, Pamela; Wagner, Mark; Forgie, Julia; Dwyer, Harry; Wolf, Katy

    2014-01-21

    To provide information for greenhouse gas reduction policies, the California Air Resources Board (CARB) inventories annual emissions of high-global-warming potential (GWP) fluorinated gases, the fastest growing sector of greenhouse gas (GHG) emissions globally. Baseline 2008 F-gas emissions estimates for selected chlorofluorocarbons (CFC-12), hydrochlorofluorocarbons (HCFC-22), and hydrofluorocarbons (HFC-134a) made with an inventory-based methodology were compared to emissions estimates made by ambient-based measurements. Significant discrepancies were found, with the inventory-based emissions methodology resulting in a systematic 42% under-estimation of CFC-12 emissions from older refrigeration equipment and older vehicles, and a systematic 114% overestimation of emissions for HFC-134a, a refrigerant substitute for phased-out CFCs. Initial, inventory-based estimates for all F-gas emissions had assumed that equipment is no longer in service once it reaches its average lifetime of use. Revised emission estimates using improved models for equipment age at end-of-life, inventories, and leak rates specific to California resulted in F-gas emissions estimates in closer agreement to ambient-based measurements. The discrepancies between inventory-based estimates and ambient-based measurements were reduced from -42% to -6% for CFC-12, and from +114% to +9% for HFC-134a.

  2. Emissions of halocarbons from mobile vehicle air conditioning system in Hong Kong.

    Science.gov (United States)

    Yan, H H; Guo, H; Ou, J M

    2014-08-15

    During the implementation of Montreal Protocol, emission inventories of halocarbons in different sectors at regional scale are fundamental to the formulation of relevant management strategy and inspection of the implementation efficiency. This study investigated the emission profile of halocarbons used in the mobile vehicle air conditioning system, the leading sector of refrigeration industry in terms of the refrigerant bank, market and emission, in the Hong Kong Special Administrative Region, using a bottom-up approach developed by 2006 IPCC Good Practice Guidance. The results showed that emissions of CFC-12 peaked at 53 tons ODP (Ozone Depletion Potential) in 1992 and then gradually diminished, whereas HFC-134a presented an increasing emission trend since 1990s and the emissions of HFC-134a reached 65,000 tons CO2-equivelant (CO2-eq) by the end of 2011. Uncertainty analysis revealed relatively high levels of uncertainties for special-purpose vehicles and government vehicles. Moreover, greenhouse gas (GHG) abatements under different scenarios indicated that potential emission reduction of HFC-134a ranged from 4.1 to 8.4 × 10(5)tons CO2-eq. The findings in this study advance our knowledge of halocarbon emissions from mobile vehicle air conditioning system in Hong Kong. Copyright © 2014 Elsevier B.V. All rights reserved.

  3. Techno-economic feasibility analysis of hydrogen fuel cell and solar photovoltaic hybrid renewable energy system for academic research building

    International Nuclear Information System (INIS)

    Singh, Anand; Baredar, Prashant; Gupta, Bhupendra

    2017-01-01

    Highlights: • A HFC and SPV HRES for stand-alone applications is proposed. • The FC program computes the optimum cost of HRES components. • HOMER pro software to calculate the optimum performance of HRES. - Abstract: A hydrogen fuel cell (HFC) and solar photovoltaic (SPV) hybrid renewable energy system (HRES) for stand-alone applications is proposed. This system arrangement of a hydrogen tank, battery, and an electrolyzer are used as like the energy storage. The economic viability of using HRES power to supply the electrical load demand of academic research building located at 23°12′N latitude and 77°24′E longitudes, India is examined. The fuzzy logic program computes the optimum value of capital and replacement cost of the components, which is then utilized in HOMER pro software to calculate the optimum performance of HRES. The results shows the HFC and battery bank are the most significant modules of the HRES to meet load demand at late night and early morning hours. The AC primary load consuming 20712.63 kWh/year out of total power generation of HRES which is 24570.72 kWh/year. The excess of electricity produced by HRES is 791.7709 kWh/year with the optimized cost of energy, unmet electrical load and capacity shortage of 0%.

  4. Biological monitoring the exposure to polycyclic aromatic hydrocarbons of coke oven workers in relation to smoking and genetic polymorphisms for GSTM1 and GSTT1

    Energy Technology Data Exchange (ETDEWEB)

    Joost H.M. van Delft; Marie-Jose S.T. Steenwinkel; Jeff G. van Asten; Nico de Vogel; Truus C.D.M. Bruijntjes-Rozier; Ton Schouten; Patricia Cramers; Lou Maas; Marcel H. van Herwijnen; Frederik-Jan van Schooten; Piet M.J. Hopmans [TNO Nutrition and Food Research Institute (Netherlands). Toxicology Division

    2001-07-01

    Occupational exposure to polycyclic aromatic hydrocarbons (PAH) increases the risk of developing lung cancer. Human exposure is often demonstrated by increased internal levels of PAH metabolites and of markers for early biological effects, like DNA adducts and cytogenetic aberrations. This study aimed to assess whether the current exposure to PAH of coke oven workers in a Dutch plant induced biological effects, and to determine if these effects are influenced by tobacco smoking and by genetic polymorphisms for the glutathione S-transferase genes GSTM1 and GSTT1. Urinary 1-hydroxypyrene (1-OHpyr) levels were used to monitor the internal dose, while the internal effective dose was assessed by monitoring PAH-DNA adducts, DNA strand breaks (Comet assay), sister-chromatid exchanges (SCE) and cells with a high frequency of SCE (HFC) in lymphocytes together with micronuclei (MN) in exfoliated urothelial cells. Occupational exposure to PAH resulted in statistically significant increased 1-OHpyr levels, but it did not cause a significant induction of SCE, HFC, MN, DNA strand breaks or DNA adducts. Smoking caused a significant increase of 1-OHpyr, SCE, HFC and DNA adducts, but not of MN or DNA strand breaks. Following correction for the smoking-related effects, no occupational induction of the effect biomarkers could be discerned. Multi-variate analysis did not show a significant influence of GSTM1 and GSTT1 polymorphisms on any biomarker. Also no significant interactions were observed between the various biomarkers.

  5. Complexon Solutions in Freon for Decontamination of Solids and SNF Treatment

    International Nuclear Information System (INIS)

    Kamachev, V.; Shadrin, A.; Murzin, A.

    2008-01-01

    Full text of publication follows: The possibility of using complexon solutions in supercritical and compressed carbon dioxide for decontamination of solid surfaces and for spent nuclear fuel (SNF) treatment was demonstrated in the works of Japanese, Russian and American researchers. The obtained data showed that the use of complexon solutions in carbon dioxide sharply decreases the volume of secondary radioactive wastes because it can be easily evaporated, purified and recycled. Moreover, high penetrability of carbon dioxide allows decontamination of surfaces with complex shape. However, one of the disadvantages of carbon dioxide is its high working pressure (10-20 MPa for supercritical CO 2 and 7 MPa for compressed CO 2 ). Moreover, in case of SNF treatment, carbon dioxide solvent will be contaminated with 14 C, which in the course of SNF dissolution in CO 2 containing TBP*HNO 3 adduct stage will be oxidized into CO 2 . These main disadvantages can be eliminated by using complexon solutions in ozone-friendly Freon HFC-134a for decontamination and SNF treatment. Our experimental data for real contaminated materials showed that the decontamination factor for complexon solutions in liquid Freon HFC-134a at 1,2 MPa and 25 deg. C is close to that attained in carbon dioxide. Moreover, the possibility of SNF treatment in Freon HFC-134a was demonstrated in trials using real SNF and its imitators. (authors)

  6. Characterization of RPC operation with new environmental friendly mixtures for LHC application and beyond

    International Nuclear Information System (INIS)

    Guida, R.; Capeans, M.; Mandelli, B.

    2016-01-01

    The large muon trigger systems based on Resistive Plate Chambers (RPC) at the LHC experiments are currently operated with R134a based mixture. Unfortunately R134a is considered a greenhouse gas with high impact on the enviroment and therefore will be subject to regulations aiming in strongly reducing the available quantity on the market. The immediat effects might be instability on the price and incertitude in the product availability. Alternative gases (HFO-1234yf and HFO-1234ze) have been already identified by industry for specific applications as replacement of R134a. Moreover, HFCs similar to the R134a but with lower global warming potential (GWP) are already available (HFC-245fa, HFC-32, HFC-152a). The present contribution describes the results obtained with RPCs operated with new enviromemtal friendly gases. A particular attention has been addressed to the possibility of maintening the current operation conditions (i.e. currently used applied voltage and front-end electronics) in order to be able to use a new mixture for RPC systems even where the common infrastructure (i.e. high voltage and detector components) cannot be replaced for operation at higher applied voltages.

  7. Ala-asteikäisten lasten viihtyvyys koulussa : Koulussa tehtävän nuorisotyön näkökulmasta

    OpenAIRE

    Träskelin, Jeanette

    2012-01-01

    Opinnäytetyössäni tarkastellaan koulun ja nuorisotyön yhteistyötä. Tavoitteena on selvittää, voiko kou-lussa tehtävä nuorisotyö vaikuttaa lasten viihtymiseen koulussa, etenkin alakoulussa, ja millaisin kei-noin. Alussa kuvailen koulussa tehtävää nuorisotyötä nykypäivänä. Kerron sen tehtävistä sekä tavoit-teista. Kuvailen myös koulua nuorisotyön toimintaympäristönä sekä lasten viihtymistä koulussa ja sii-hen vaikuttavia asioita. Pääosin laadullisessa tutkimuksessani haastattelin Helsingis...

  8. Consumer buying behavior in fashion retailing

    OpenAIRE

    Ramoškaitė, Neringa

    2011-01-01

    Temos aktualumas. Pasaulinė mados pramonė yra vienas iš svarbiausių ekonomikos sektorių kapitalo, pajamų, prekybos ir darbo vietos požiūriu visame pasaulyje. Aprangos pramonė turi trumpą produkto gyvavimo ciklą, milžinišką produktų įvairovę, nepastovią ir nenuspėjamą paklausą, ilgus ir lanksčius tiekimo procesus. Mados mažmenininkų gebėjimas greitai pristatyti naujausią madą parduotuvėje dabar yra būtinybė, nes mados stiliai ir tendencijos keičiasi vis greičiau ir reguliariau. Yra mados mažme...

  9. [Artificial Intelligence in Drug Discovery].

    Science.gov (United States)

    Fujiwara, Takeshi; Kamada, Mayumi; Okuno, Yasushi

    2018-04-01

    According to the increase of data generated from analytical instruments, application of artificial intelligence(AI)technology in medical field is indispensable. In particular, practical application of AI technology is strongly required in "genomic medicine" and "genomic drug discovery" that conduct medical practice and novel drug development based on individual genomic information. In our laboratory, we have been developing a database to integrate genome data and clinical information obtained by clinical genome analysis and a computational support system for clinical interpretation of variants using AI. In addition, with the aim of creating new therapeutic targets in genomic drug discovery, we have been also working on the development of a binding affinity prediction system for mutated proteins and drugs by molecular dynamics simulation using supercomputer "Kei". We also have tackled for problems in a drug virtual screening. Our developed AI technology has successfully generated virtual compound library, and deep learning method has enabled us to predict interaction between compound and target protein.

  10. Kaimo vietovių bibliotekos reikšmė bendruomenėje

    OpenAIRE

    Janavičienė, Daiva

    2011-01-01

    Keičiantis kaimo bendruomenių poreikiams, bibliotekos adaptuoja teikiamas paslaugas, išlikdamos reikšmingos bendruomenėms. Viešosios bibliotekos atsirado iš bendruomenės narių poreikio skaityti, gauti kultūrines paslaugas. XX amžiaus tėkmėje kaimo bibliotekos, kaip ir visos Lietuvos viešosios bibliotekos, praėjo keletą sunkių laikotarpių – nelengvą kūrimąsi Lietuvos nepriklausomybės laikotarpiu, antrojo pasaulinio karo sugriovimus, sovietinio laikotarpio politizacijos įtaką, sudėtingus atgimi...

  11. Selvitys HR House Oy:n vuokratyöntekijöiden työtyytyväisyydestä

    OpenAIRE

    Kaskela, Leeni

    2011-01-01

    Opinnäytetyön tarkoituksena oli selvittää HR House Oy:n palveluksessa olevien vuokratyöntekijöiden työtyytyväisyyteen vaikuttavia asioita. Opinnäytetyö on laadullinen tutkielma, jossa käytän tutkimusmenetelmänä teemahaastattelua. Tutkimuskysymykseni selvittävät, mitkä asiat vaikuttavat työntekijöiden työ- tyytyväisyyteen ja mitä he kertovat työtyytyväisyyteen vaikuttavista tekijöistä. Toimeksianto opinnäytetyön tekemiseen on tullut HR House Oy Henkilöstöpalveluilta. Tavoitteena oli löytää kei...

  12. Panel: Opportunities and Challenges of Writing in a Second Language

    DEFF Research Database (Denmark)

    Kupatadze, Ketevan; Chiu, Scott C.; Cozart, Stacey Marie

    /foreign language. This is particularly true when one teaches adult groups of students who have already formed distinct identities as academically and professionally successful L1 writers. The participants of our panel will look at students from different backgrounds with the shared interest in finding out how...... (Richard Kern 2000, Claire Krasch, 1993); Wiring assessment (Carl Bereiter, 1995); Learning and writing transfer (Greeno, Smith, and Moore, 1993), Second language writing (Tony Silva and Paul Kei Matsuda, 2010). Paper (1): Bridging the Danglish Gap: A Study of Danish Doctoral Students’ Experiences...... knowledge and principles to the writing situations they perceive as suitable or doable. Students’ perception about the role of language in Globalized world and language learning, as well as their self-perception plays an integral role in their ability to transfer knowledge when writing in a second...

  13. Šeimai palankios politikos įgyvendinimas Lietuvoje: problemos ir galimybės

    OpenAIRE

    Jančaitytė, Raminta

    2006-01-01

    Tradicinis požiūris, kad darbas ir šeima nesuderinami ir šeimos rūpesčius reikia „palikti už darbovietės ribų“, keičiasi labai lėtai. Nelankstus darbo laikas, reikalavimas dirbti viršvalandžius, per mažos pajamos, verčiančios dirbti keliose darbovietėse, sukelia darbo ir pareigų šeimai derinimo problemų, trukdo tėvams skirti pakankamai dėmesio vaikų priežiūrai ir auklėjimui. Atsiranda palankios darbo vietos poreikis, kad būtų lanksčiai reaguojama į darbuotojų problemas, susijusias su rūpinimu...

  14. Medium-chain triglyceride ameliorates insulin resistance and inflammation in high fat diet-induced obese mice.

    Science.gov (United States)

    Geng, Shanshan; Zhu, Weiwei; Xie, Chunfeng; Li, Xiaoting; Wu, Jieshu; Liang, Zhaofeng; Xie, Wei; Zhu, Jianyun; Huang, Cong; Zhu, Mingming; Wu, Rui; Zhong, Caiyun

    2016-04-01

    The aim of the present study was to investigate the in vivo effects of dietary medium-chain triglyceride (MCT) on inflammation and insulin resistance as well as the underlying potential molecular mechanisms in high fat diet-induced obese mice. Male C57BL/6J mice (n = 24) were fed one of the following three diets for a period of 12 weeks: (1) a modified AIN-76 diet with 5 % corn oil (normal diet); (2) a high-fat control diet (17 % w/w lard and 3 % w/w corn oil, HFC); (3) an isocaloric high-fat diet supplemented with MCT (17 % w/w MCT and 3 % w/w corn oil, HF-MCT). Glucose metabolism was evaluated by fasting blood glucose levels and intraperitoneal glucose tolerance test. Insulin sensitivity was evaluated by fasting serum insulin levels and the index of homeostasis model assessment-insulin resistance. The levels of serum interleukin-6 (IL-6), interleukin-10 (IL-10), and tumor necrosis factor-α were measured by ELISA, and hepatic activation of nuclear factor κB (NF-κB) and mitogen-activated protein kinase (MAPK) pathways was determined using western blot analysis. Compared to HFC diet, consumption of HF-MCT did not induce body weight gain and white adipose tissue accumulation in mice. HFC-induced increases in serum fasting glucose and insulin levels as well as glucose intolerance were prevented by HF-MCT diet. Meanwhile, HF-MCT resulted in significantly lower serum IL-6 level and higher IL-10 level, and lower expression levels of inducible nitric oxide synthase and cyclooxygenase-2 protein in liver tissues when compared to HFC. In addition, HF-MCT attenuated HFC-triggered hepatic activation of NF-κB and p38 MAPK. Our study demonstrated that MCT was efficacious in suppressing body fat accumulation, insulin resistance, inflammatory response, and NF-κB and p38 MAPK activation in high fat diet-fed mice. These data suggest that MCT may exert beneficial effects against high fat diet-induced insulin resistance and inflammation.

  15. Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

  16. FY 2000 report on the results of the joint research - Field test project on the photovoltaic power generation for public facility use; 2000 nendo kyodokenkyu gyomu seika hokokusho. Kokyo shisetsu you taiyoko hatsuden field test jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper arranged the FY 2000 results of the field test on the photovoltaic power generation for public facility use, etc. This report described in detail the results obtained at 237 places including the following: Social Welfare Corp. Seimei-kai, Kobe City (Hyogo Prefecture), Iitaka Town of Iinan County (Mie Prefecture), Kyushu Electric Safety Association, Educational Corp. Kongo Gakuen, Social Welfare Corp. Izumi-kai, Educational Corp. Shiobara Ikuei-kai, Educational Corp. Aiko Gakuen, Social Welfare Corp. Tachibana-kai, Cooperative Association Co-op Kobe, Social Welfare Corp. Hoshizuki-no-sato, Tochigi-Fuji Industrial Co., Hirabayashi Section of Gamo Town of Gamo County (Shiga Prefecture), Yanagawa City (Fukuoka Prefecture), Imadate City of Imadate County (Fukui Prefecture), Osaka Prefecture, Yamanashi Prefecture, Utazu Town of Ayauta County (Kagawa Prefecture), Educational Corp. Fukuyama Gakuen, New Energy Business Cooperative Association, Meitec Corp., Shikoku Medicom Co., Shizen Kobo Co., Educational Corp. Horikoshi Gakuen, Matama Town of Nishi-Kunisaki County (Oita Prefecture), Nio Town of Mitoyo County (Kagawa Prefecture), Educational Corp. Koshien Gakuin, Sansei Giken Co., Mitsui Greenland Co., AWI Mach Co., Nagoya City and Educational Corp. Kibogaoka Gakuen. (NEDO)

  17. Present status of inertial confinement fusion in Japan

    International Nuclear Information System (INIS)

    Yamanaka, Chiyoe

    1984-01-01

    The Japanese inertial fusion program has made important progress towards implosion fusion process and the technical development required for realizing the breakeven of inertial fusion energy. The key issues for the ICF research are the development of a high power driver, the pertinent pellet design for implosion by a super computer code, and the diagnostics of implosion process with high space and time resolution. The Institute of Laser Engineering (ILE), Osaka University, is the central laboratory for ICF research in Japan. The ILE Osaka has advanced the Kongo Project aiming at the breakeven of inertial fusion since 1980, and as the first phase, the Gekko 12 Nd glass laser of 20 kJ having 12 beams was constructed. The ILE has also the Lekko 8 CO 2 laser and the Reiden 4 light ion beam machine. In the second phase, a 100 kJ class driver will be provided. At the ILE, rare gas halide lasers such as KrF and ArF have been investigated. Laser plasma coupling, the scaling law for implosion pressure, the invention of a new type target ''Cannonball'', and the development of computer codes are described. Also the activities in universities, government laboratories and industrial companies are reported. (Kako, I.)

  18. Field evaluation of spatial repellency of metofluthrin-impregnated plastic strips against Anopheles gambiae complex in Bagamoyo, coastal Tanzania.

    Science.gov (United States)

    Kawada, Hitoshi; Temu, Emmanuel A; Minjas, Japhet N; Matsumoto, Osamu; Iwasaki, Tomonori; Takagi, Masahiro

    2008-09-01

    Metofluthrin is a newly synthesized pyrethroid possessing high knockdown and lethal activity against mosquitoes. Studies of metofluthrin-impregnated plastic strips have been performed with dengue vectors. This study reports the efficacy of the new prototypes of metofluthrin-impregnated plastic strips against malaria vectors, Anopheles gambiae complex, in the Kongo villages of Bagamoyo district in coastal Tanzania. The study, using 20 houses, half intervention, half control, was conducted for a 124-day period. Pyrethrum spray sheets and Centers for Disease Control and Prevention light traps were used to sample mosquito population indices. The mosquito density indices of the intervention houses were observed to be significantly lower than those of the control houses when pyrethrum spray sheet collection was used (F = 4.61, 1 df, P = 0.038; 98.7% reduction of total mosquito collection compared with that for the controls). These low indices were observed despite the large openings found in Bagamoyo houses, which were predicted to have a considerable negative effect on the spatial repellency of metofluthrin. Based on the present results, the pyrethrum spray sheet collection was the better of the 2 collection methods.

  19. Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

  20. Air pollution is associated with the development of atherosclerosis via the cooperation of CD36 and NLRP3 inflammasome in ApoE-/- mice.

    Science.gov (United States)

    Du, Xihao; Jiang, Shuo; Zeng, Xuejiao; Zhang, Jia; Pan, Kun; Zhou, Ji; Xie, Yuquan; Kan, Haidong; Song, Weimin; Sun, Qinghua; Zhao, Jinzhuo

    2018-06-15

    Previous studies have indicated that the main air pollutant fine particulate matter (≤2.5 μm; PM 2.5 ) exposure is associated with the development of atherosclerosis. Although the mechanism is not fully illustrated, the inflammatory responses play an important role. The present study aimed to explore whether PM 2.5 -exacerbated atherosclerosis was mediated by the cooperation of cluster of differentiation 36 (CD36) and nucleotide-binding oligomerization domain-like receptor protein (NLRP3) inflammasome in apolipoprotein E -/- (ApoE -/- ) mice. Thirty-two ApoE -/- mice were randomly divided into two groups. One group was fed with high fat chow (HFC) for 10 weeks to establish atherosclerotic model, and the other was fed with normal chow (NC). From week 11, the mice were exposed to concentrated PM 2.5 (PM) or filtered air (FA) using Shanghai Meteorological and Environmental Animal Exposure System for 16 weeks. In both NC and HFC groups, PM 2.5 exposure induced the formation of atherosclerosis plaque. Similarly, PM mice appeared higher lipid content in the aortic root than that in the FA mice. Compared with the FA mice, PM mice appeared a decrease in high density lipoprotein-cholesterol (HDL-C) and apolipoprotein A1 along with an increase in apolipoprotein B, low density lipoprotein-cholesterol (LDL-C) and oxidized low-density lipoprotein (ox-LDL). Moreover, PM 2.5 exposure induced increase of CD36 in serum and aorta. In both NC and HFC groups, NLRP3 inflammasome activation-related indicators were activated or increased in the aorta of the PM mice when compared with the FA mice. The cooperation of CD36 and NLRP3 inflammasome activation may be the potential mechanisms linkixposed to concentrated PM 2.5 (PM) or filtered air (FA) using Shanghai Meteorological and Environmental Animal Exposure System for 16 weeks. In both NC and HFC groups, PM 2.5 exposure induced the formation of atherosclerosis plaque. Similarly, PM mice appeared higher lipid content in the aortic

  1. Direct facility funding as a response to user fee reduction: implementation and perceived impact among Kenyan health centres and dispensaries.

    Science.gov (United States)

    Opwora, Antony; Kabare, Margaret; Molyneux, Sassy; Goodman, Catherine

    2010-09-01

    There is increasing pressure for reduction of user fees, but this can have adverse effects by decreasing facility-level funds. To address this, direct facility funding (DFF) was piloted in Coast Province, Kenya, with health facility committees (HFCs) responsible for managing the funds. We evaluated the implementation and perceived impact 2.5 years after DFF introduction. Quantitative data collection at 30 public health centres and dispensaries included a structured interview with the in-charge, record reviews and exit interviews. In addition, in-depth interviews were conducted with the in-charge and HFC members at 12 facilities, and with district staff and other stakeholders. DFF procedures were well established: HFCs met regularly and accounting procedures were broadly followed. DFF made an important contribution to facility cash income, accounting for 47% in health centres and 62% in dispensaries. The main items of expenditure were wages for support staff (32%), travel (21%), and construction and maintenance (18%). DFF was perceived to have a highly positive impact through funding support staff such as cleaners and patient attendants, outreach activities, renovations, patient referrals and increasing HFC activity. This was perceived to have improved health worker motivation, utilization and quality of care. A number of problems were identified. HFC training was reportedly inadequate, and no DFF documentation was available at facility level, leading to confusion. Charging user fees above those specified in the national policy remained common, and understanding of DFF among the broader community was very limited. Finally, relationships between HFCs and health workers were sometimes characterized by mistrust and resentment. Relatively small increases in funding may significantly affect facility performance when the funds are managed at the periphery. Kenya plans to scale up DFF nationwide. Our findings indicate this is warranted, but should include improved training

  2. Emissions of halocarbons from mobile vehicle air conditioning system in Hong Kong

    International Nuclear Information System (INIS)

    Yan, H.H.; Guo, H.; Ou, J.M.

    2014-01-01

    Highlights: • Halocarbon emissions from MVACS were characterized using bottom up approach. • Quantification of emission inventory was revealed using AUV Tools. • Potential emission reduction was estimated under 3 possible mitigation scenarios. • The results are useful for the policy makers to formulate and implement future phase-out schedule. - Abstract: During the implementation of Montreal Protocol, emission inventories of halocarbons in different sectors at regional scale are fundamental to the formulation of relevant management strategy and inspection of the implementation efficiency. This study investigated the emission profile of halocarbons used in the mobile vehicle air conditioning system, the leading sector of refrigeration industry in terms of the refrigerant bank, market and emission, in the Hong Kong Special Administrative Region, using a bottom-up approach developed by 2006 IPCC Good Practice Guidance. The results showed that emissions of CFC-12 peaked at 53 tons ODP (Ozone Depletion Potential) in 1992 and then gradually diminished, whereas HFC-134a presented an increasing emission trend since 1990s and the emissions of HFC-134a reached 65,000 tons CO 2 -equivelant (CO 2 -eq) by the end of 2011. Uncertainty analysis revealed relatively high levels of uncertainties for special-purpose vehicles and government vehicles. Moreover, greenhouse gas (GHG) abatements under different scenarios indicated that potential emission reduction of HFC-134a ranged from 4.1 to 8.4 × 10 5 tons CO 2 -eq. The findings in this study advance our knowledge of halocarbon emissions from mobile vehicle air conditioning system in Hong Kong

  3. High temperature diffusion of hafnium in tungsten and a tungsten-hafnium carbide alloy

    International Nuclear Information System (INIS)

    Ozaki, Y.; Zee, R.H.

    1994-01-01

    Refractory metals and ceramics are used extensively in energy systems due to their high temperature properties. This is particularly important in direct conversion systems where thermal to electric conversion efficiency is a direct function of temperature. Tungsten, which has the highest melting temperature among elemental metals, does not possess sufficient creep resistance at temperature above 1,600 K. Different dispersion strengthened tungsten alloys have been developed to extend the usefulness of tungsten to higher temperatures. One of these alloys, tungsten with 0.4 mole percent of finely dispersed HfC particles (W-HfC), has the optimum properties for high temperature applications. Hafnium carbide is used as the strengthening agent due to its high chemical stability and its compatibility with tungsten. The presence of HfC particles retards the rate of grain growth as well as restricting dislocation motion. Both of which are beneficial for creep resistance. The long term behavior of this alloy depends largely on the evolution of its microstructure which is governed by the diffusion of its constituents. Data on the diffusion of carbon in tungsten and tungsten self-diffusion are available, but no direct measurements have been made on the diffusion of hafnium in tungsten. The only diffusion data available are estimated from a coarsening study and these data are highly unreliable. In this study, the diffusion behavior of hafnium in pure tungsten and in a W-HfC alloy was directly measured by means of Secondary Ion Mass Spectroscopy (SIMS). The selection of the W-HfC alloy is due to its importance in high temperature engineering applications, and its higher recrystallization temperature. The presence of HfC particles in tungsten restricts grain growth resulting in better high temperature creep resistance. The higher recrystallization temperature allows measurements to be made over a wider range of temperatures at a relatively constant grain size

  4. Emissions of halocarbons from mobile vehicle air conditioning system in Hong Kong

    Energy Technology Data Exchange (ETDEWEB)

    Yan, H.H.; Guo, H., E-mail: ceguohai@polyu.edu.hk; Ou, J.M.

    2014-08-15

    Highlights: • Halocarbon emissions from MVACS were characterized using bottom up approach. • Quantification of emission inventory was revealed using AUV Tools. • Potential emission reduction was estimated under 3 possible mitigation scenarios. • The results are useful for the policy makers to formulate and implement future phase-out schedule. - Abstract: During the implementation of Montreal Protocol, emission inventories of halocarbons in different sectors at regional scale are fundamental to the formulation of relevant management strategy and inspection of the implementation efficiency. This study investigated the emission profile of halocarbons used in the mobile vehicle air conditioning system, the leading sector of refrigeration industry in terms of the refrigerant bank, market and emission, in the Hong Kong Special Administrative Region, using a bottom-up approach developed by 2006 IPCC Good Practice Guidance. The results showed that emissions of CFC-12 peaked at 53 tons ODP (Ozone Depletion Potential) in 1992 and then gradually diminished, whereas HFC-134a presented an increasing emission trend since 1990s and the emissions of HFC-134a reached 65,000 tons CO{sub 2}-equivelant (CO{sub 2}-eq) by the end of 2011. Uncertainty analysis revealed relatively high levels of uncertainties for special-purpose vehicles and government vehicles. Moreover, greenhouse gas (GHG) abatements under different scenarios indicated that potential emission reduction of HFC-134a ranged from 4.1 to 8.4 × 10{sup 5} tons CO{sub 2}-eq. The findings in this study advance our knowledge of halocarbon emissions from mobile vehicle air conditioning system in Hong Kong.

  5. Looking for New Polycrystalline MC-Reinforced Cobalt-Based Superalloys Candidate to Applications at 1200°C

    Directory of Open Access Journals (Sweden)

    Patrice Berthod

    2017-01-01

    Full Text Available For applications for which temperatures higher than 1150°C can be encountered the currently best superalloys, the γ/γ′ single crystals, cannot be used under stress because of the disappearance of their reinforcing γ′ precipitates at such temperatures which are higher than their solvus. Cobalt-based alloys strengthened by refractory and highly stable carbides may represent an alternative solution. In this work the interest was focused on MC carbides of several types. Alloys were elaborated with atomically equivalent quantities in M element (among Ti, Ta, Nb, Hf, or Zr and in C. Script-like eutectic TiC, TaC, NbC, HfC, and ZrC carbides were successfully obtained in the interdendritic spaces. Unfortunately, only one type, HfC, demonstrated high morphological stability during about 50 hours at 1200°C. The concerned alloy, of the Co-25Cr-0.5C-7.4Hf type (in wt.%, was further characterized in flexural creep resistance and air-oxidation resistance at the same temperature. The creep behaviour was very good, notably by comparison with a more classical Co-25Cr-0.5C-7.5Ta alloy, proving that the interest of HfC is higher than the TaC one. In contrast the oxidation by air was faster and its behaviour not really chromia-forming. Significant improvements of this chemical resistance are expected before taking benefit from the mechanical superiority of this alloy.

  6. Synergistic effect of carbon nanotube as sintering aid and toughening agent in spark plasma sintered molybdenum disilicide-hafnium carbide composite

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, Biswajyoti; Asiq Rahman, O.S.; Sribalaji, M [Materials Science and Engineering, Indian Institute of Technology Patna, Bihta Kanpa Road, Bihta, Patna, Bihar 801103 (India); Bakshi, Srinivasa Rao [Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai 600036 (India); Keshri, Anup Kumar, E-mail: anup@iitp.ac.in [Materials Science and Engineering, Indian Institute of Technology Patna, Bihta Kanpa Road, Bihta, Patna, Bihar 801103 (India)

    2016-12-15

    Hafnium carbide (HfC) along with sintering aids was consolidated at a relatively lower temperature i.e. 1600 °C (i.e. T=~0.41 T{sub m}) under a uniaxial load of 50 MPa by spark plasma sintering. Two different sintering aids such as molybdenum disilicide (MoSi{sub 2}) and carbon nanotube (CNT) were added to enhance the densification and lower the extent of grain growth in the sintered pellets. Density of the sintered pellet increased from 96.0±0.8% in HfC +5 wt% MoSi{sub 2} (HM) to 99.0±0.5% with the addition of 2 wt% CNT in HfC+5 wt% MoSi{sub 2} (HMC) at sintering temperature of 1600 °C. Further, the extent of grain growth drastically reduced from 204% in HM to 50% in HMC. Analysis of linear shrinkage during densification revealed that CNT addition increased densification rate and decreased the time required to reach the density of 99.0±0.5% at 1600 °C. Increased densification and lower degree of grain growth could be due to the synergistic effect offered by the CNT, which are as follows: (i) Lubrication effect of CNT, (ii) Lower activation energy for grain boundary diffusion (iii) Reduction in liquid phase sintering temperature and (iv) Grain boundary pinning. Fracture toughness of the sintered HM and HMC composite was obtained using indentation technique. By the addition of 2 wt% CNT in HM, drastic increase of 91% in fracture toughness was seen. This significant improvement in fracture toughness was due to the enhanced densification and relatively lower grain size of HMC. Also crack bridging, crack deflection, crack arrest, CNT and graphene sheet pull-out and swording played major role in toughening of HMC pellet.

  7. Novel mechanisms for the vitamin D receptor (VDR) in the skin and in skin cancer.

    Science.gov (United States)

    Bikle, Daniel D; Oda, Yuko; Tu, Chia-Ling; Jiang, Yan

    2015-04-01

    The VDR acting with or without its principal ligand 1,25(OH)2D regulates two central processes in the skin, interfollicular epidermal (IFE) differentiation and hair follicle cycling (HFC). Calcium is an important co-regulator with 1,25(OH)2D at least of epidermal differentiation. Knockout of the calcium sensing receptor (CaSR) in addition to VDR accelerates the development of skin cancer in mice on a low calcium diet. Coactivators such as mediator 1 (aka DRIP205) and steroid receptor coactivator 3 (SRC3) regulate VDR function at different stages of the differentiation process, with Med 1 essential for hair follicle differentiation and early stages of epidermal differentiation and proliferation and SRC3 essential for the latter stages of differentiation including formation of the permeability barrier and innate immunity. The corepressor of VDR, hairless (HR), is essential for hair follicle cycling, although its effect on epidermal differentiation in vivo is minimal. In its regulation of HFC and IFE VDR controls two pathways-wnt/β-catenin and sonic hedgehog (SHH). In the absence of VDR these pathways are overexpressed leading to tumor formation. Whereas, VDR binding to β-catenin may block its activation of TCF/LEF1 sites, β-catenin binding to VDR may enhance its activation of VDREs. 1,25(OH)2D promotes but may not be required for these interactions. Suppression of SHH expression by VDR, on the other hand, requires 1,25(OH)2D. The major point of emphasis is that the role of VDR in the skin involves a number of novel mechanisms, both 1,25(OH)2D dependent and independent, that when disrupted interfere with IFE differentiation and HFC, predisposing to cancer formation. This article is part of a Special Issue entitled '17th Vitamin D Workshop'. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. HFCs contribution to the greenhouse effect. Present and projected estimations

    Energy Technology Data Exchange (ETDEWEB)

    Libre, J.M.; Elf-Atochem, S.A. [Central Research & Development, Paris (France)

    1997-12-31

    This paper reviews data that can be used to calculate hydrofluorocarbon (HFC) contribution to the greenhouse effect and compare it to other trace gas contributions. Projections are made for 2010 and 2100 on the basis of available emission scenarios. Industrial judgement on the likelihood of those scenarios is also developed. Calculations can be made in two different ways: from Global Warming Potential weighted emissions of species or by direct calculation of radiative forcing based on measured and projected atmospheric concentrations of compounds. Results show that HFCs corresponding to commercial uses have a negligible contribution to the greenhouse effect in comparison with other trace gases. The projected contributions are also very small even if very high emission scenarios are maintained for decades. In 2010 this contribution remains below 1%. Longer term emissions projections are difficult. However, based on the IPCC scenario IS92a, in spite of huge emissions projected for the year 2100, the HFC contribution remains below 3%. Actually many factors indicate that the real UFC contribution to the greenhouse effect will be even smaller than presented here. Low emissive systems and small charges will likely improve sharply in the future and have drastically improved in the recent past. HFC technology implementation is likely to grow in the future, reach a maximum before the middle of the next century; the market will stabilise driven by recycling, closing of systems and competitive technologies. This hypothesis is supported by previous analysis of the demand for HTCs type applications which can be represented by {open_quotes}S{close_quotes} type curves and by recent analysis indicating that the level of substitution of old products by HFCs is growing slowly. On the basis of those data and best industrial judgement, the contribution of HFCs to the greenhouse effect is highly likely to remain below 1% during the next century. 11 refs., 2 figs., 5 tabs.

  9. Effects of superfine refractory carbide additives on microstructure and mechanical properties of TiB2–TiC+Al2O3 composite ceramic cutting tool materials

    International Nuclear Information System (INIS)

    Zou, Bin; Ji, Wenbin; Huang, Chuanzhen; Wang, Jun; Li, Shasha; Xu, Kaitao

    2014-01-01

    Highlights: • The superfine carbides determined the mechanical properties of composites. • Superfine HfC or TaC caused some oxide impurities in composites. • Superfine VC or NbC refined and homogenized the microstructure. • Failure of composites containing HfC or TaC was produced by larger grains. • Composite containing VC exhibited more bridging and transcrystalline failure. -- Abstract: A study to increase the mechanical properties of TiB 2 –TiC+Al 2 O 3 composite ceramic cutting tool material by using superfine refractory carbide additives is presented. Four superfine refractory carbides are considered to investigate their effects on the phase composition, element distribution, grain size, fracture surface, crack propagation of the metal ceramic. The physicochemical properties of superfine carbides, such as chemical activities and atom radius, were found to have the significant effects on the microstructure and mechanical properties of the metal ceramic. Hafnium carbide (HfC) and Tantalum carbide (TaC) reduced the mechanical properties of the metal ceramic because of their poor solubility with the Ni binder phase and the formation of oxides. The mechanical properties of the metal ceramic were increased by the addition of superfine niobium carbide (NbC) and vanadium carbide (VC), and their optimum values were a flexural strength of 1100 ± 62 MPa, fracture toughness of 8.5 ± 0.8 MPa.m1/2 and hardness of 21.53 ± 0.36 GPa, respectively, when 3.2 wt% superfine VC was used

  10. Experimental Study of Flow Boiling Heat Transfer in a Horizontal Microfin Tube

    OpenAIRE

    Yu, Jian; Koyama, Shigeru; Momoki, Satoru

    1995-01-01

    An experimental study on flow boiling heat transfer in a horizontal microfin tube is conducted with pure refrigerants HFC134a, HCFC123 and HCFC22 using a water-heated double-tube type test section. The test microfin tube is a copper tube having the following dimensions: 8.37mm mean inside diameter, 0.168mm fin height, 60fin number and 18 degree of helix angle. The local heat transfer coefficients for both counter and parallel flows are measured in a range of heat flux of 1 to 93W/m^2, mass ve...

  11. Experimental study on void fraction of two-phase flow inside a micro-fin tube

    OpenAIRE

    Koyama, Shigeru; Chen, Yongchang; Kitano, Ryuji; Kuwahara, Ken

    2001-01-01

    In this paper the void fraction and flow pattern of the two-phase flow in a micro-fin tube were investigated experimentally for a pure refrigerant HFC134a. The experiment was carried out at a pressure range of 0.6 and 1.2MPa with mass velocities of 90 and 180kg/m^2 s, in which the vapor quality varied from 0 to 1. The void fraction was measured by means of simultaneously closing valves of both sides of the test tube at adiabatic condition. Experimental results for the micro-fin tube were comp...

  12. 01 - The sustainable management of radioactive materials with fourth-generation reactors

    International Nuclear Information System (INIS)

    2012-12-01

    This publication first explains the reasons for the development of fourth-generation nuclear systems: the issue of resources, the issue of used fuels, technologies for fast breeder fourth-generation reactors, the alternative of HFC-cooled light water reactors, the potential market for fast-breeder reactors, strategies in different countries. Then, the authors address the strategy development for these fourth-generation reactors: requirements, safety, economic competitiveness, resistance to proliferation, flexible management of nuclear resources, development scheme (sodium or gas-based heat transfer), and fuel cycle. They finally discuss the possible transition scenarios towards this new generation

  13. Halogenated greenhouse gases at the Swiss High Alpine Site of Jungfraujoch (3580 m asl): Continuous measurements and their use for regional European source allocation

    Science.gov (United States)

    Reimann, Stefan; Schaub, Daniel; Stemmler, Konrad; Folini, Doris; Hill, Matthias; Hofer, Peter; Buchmann, Brigitte; Simmonds, Peter G.; Greally, Brian R.; O'Doherty, Simon

    2004-03-01

    At the high Alpine site of Jungfraujoch (3580 m asl), 23 halogenated greenhouse gases are measured quasi-continuously by gas chromatography-mass spectrometry (GCMS). Measurement data from the years 2000-2002 are analyzed for trends and pollution events. Concentrations of the halogenated trace gases, which are already controlled in industrialized countries by the Montreal Protocol (e.g., CFCs) were at least stable or declining. Positive trends in the background concentrations were observed for substances which are used as CFC-substitutes (hydrofluorocarbons, hydrochlorofluorocarbons). Background concentrations of the hydrofluorocarbons at the Jungfraujoch increased from January 2000 until December 2002 as follows: HFC 134a (CF3CH2F) from 15 to 27 ppt, HFC 125 (CF3CHF2) from 1.4 to 2.8 ppt, and HFC 152a (CHF2CH3) from 2.3 to 3.2 ppt. For HFC 152a, a distinct increase of its concentration magnitude during pollution events was observed from 2000 to 2002, indicating rising European emissions for this compound. Background concentrations of all measured compounds were in good agreement with similar measurements at Mace Head, Ireland. On the other hand, peak concentrations were significantly higher at the Jungfraujoch. This finding is due to the proximity to potent European sources, foremost in southern Europe. The average ratio of halocarbons versus carbon monoxide (CO) concentrations above their baseline values was used to estimate source strengths for the part of Europe which most influences the Jungfraujoch during pollution events. HFCs emission estimates from Jungfraujoch tend to be higher than figures at Mace Head (Ireland) from the end of the 1990s, which either reflects the increased use of these compounds or the closer location of Jungfraujoch to major southern European sources. Transport of polluted European boundary layer air masses to the high Alpine site was observed especially during frontal passages, foehn events, and thermal lifting of air masses in summer

  14. High-dose supplementation with natural α-tocopherol does neither alter the pharmacodynamics of atorvastatin nor its phase I metabolism in guinea pigs

    International Nuclear Information System (INIS)

    Podszun, Maren C.; Grebenstein, Nadine; Hofmann, Ute; Frank, Jan

    2013-01-01

    It has been hypothesized in the literature that intake of high-dosage vitamin E supplements might alter the expression of cytochrome P 450 enzymes (CYP), particularly CYP3A4, which may lead to adverse nutrient–drug interactions. Because previously published studies reported conflicting findings, we investigated the pharmacodynamics of the lipid-lowering drug atorvastatin (ATV), a CYP3A4 substrate, in response to high-dose α-tocopherol (αT) feeding and determined protein expression and activities of relevant CYP. Groups of ten female Dunkin–Hartley guinea pigs were fed a control (5% fat) or a high-fat control diet (HFC; 21% fat, 0.15% cholesterol) or the HFC diet fortified with αT (250 mg/kg diet), ATV (300 mg/kg diet) or both ATV + αT for 6 weeks. Relative to control, HFC animals had increased serum cholesterol concentrations, which were significantly reduced by ATV. High-dose αT feeding in combination with ATV (ATV + αT), albeit not αT feeding alone (αT), significantly lowered serum cholesterol relative to HFC, but did not alter the cholesterol-lowering activity of the drug compared to the ATV treated guinea pigs. Protein expression of CYP3A4, CYP4F2, CYP20A1 and OATP C was similar in all groups. Accordingly, no differences in plasma concentrations of phase I metabolites of ATV were observed between the ATV and ATV + αT groups. In conclusion, feeding guinea pigs high-doses of αT for 6 weeks did neither alter the hepatic expression of CYP, nor the pharmacodynamics and metabolism of ATV. High-dose αT intake is thus unlikely to change the efficacy of drugs metabolized by CYP enzymes, particularly by CYP3A4. -- Highlights: ► Vitamin E-atorvastatin interactions were studied in hypercholesterolemic guinea pigs. ► High-dose α-tocopherol did not alter the lipid-lowering efficacy of atorvastatin. ► α-Tocopherol did not change the expression of CYP3A4, CYP4F2, CYP20A or OATP C. ► α-Tocopherol did not affect phase I metabolism of atorvastatin.

  15. High-dose supplementation with natural α-tocopherol does neither alter the pharmacodynamics of atorvastatin nor its phase I metabolism in guinea pigs

    Energy Technology Data Exchange (ETDEWEB)

    Podszun, Maren C.; Grebenstein, Nadine [Institute of Biological Chemistry and Nutrition, University of Hohenheim, D-70599 Stuttgart (Germany); Hofmann, Ute [Dr. Margarete Fischer-Bosch Institute of Clinical Pharmacology, D-70376 Stuttgart (Germany); Frank, Jan [Institute of Biological Chemistry and Nutrition, University of Hohenheim, D-70599 Stuttgart (Germany); Department of Nutrition and Food Science, University of Bonn, D-53115 Bonn (Germany)

    2013-02-01

    It has been hypothesized in the literature that intake of high-dosage vitamin E supplements might alter the expression of cytochrome P{sub 450} enzymes (CYP), particularly CYP3A4, which may lead to adverse nutrient–drug interactions. Because previously published studies reported conflicting findings, we investigated the pharmacodynamics of the lipid-lowering drug atorvastatin (ATV), a CYP3A4 substrate, in response to high-dose α-tocopherol (αT) feeding and determined protein expression and activities of relevant CYP. Groups of ten female Dunkin–Hartley guinea pigs were fed a control (5% fat) or a high-fat control diet (HFC; 21% fat, 0.15% cholesterol) or the HFC diet fortified with αT (250 mg/kg diet), ATV (300 mg/kg diet) or both ATV + αT for 6 weeks. Relative to control, HFC animals had increased serum cholesterol concentrations, which were significantly reduced by ATV. High-dose αT feeding in combination with ATV (ATV + αT), albeit not αT feeding alone (αT), significantly lowered serum cholesterol relative to HFC, but did not alter the cholesterol-lowering activity of the drug compared to the ATV treated guinea pigs. Protein expression of CYP3A4, CYP4F2, CYP20A1 and OATP C was similar in all groups. Accordingly, no differences in plasma concentrations of phase I metabolites of ATV were observed between the ATV and ATV + αT groups. In conclusion, feeding guinea pigs high-doses of αT for 6 weeks did neither alter the hepatic expression of CYP, nor the pharmacodynamics and metabolism of ATV. High-dose αT intake is thus unlikely to change the efficacy of drugs metabolized by CYP enzymes, particularly by CYP3A4. -- Highlights: ► Vitamin E-atorvastatin interactions were studied in hypercholesterolemic guinea pigs. ► High-dose α-tocopherol did not alter the lipid-lowering efficacy of atorvastatin. ► α-Tocopherol did not change the expression of CYP3A4, CYP4F2, CYP20A or OATP C. ► α-Tocopherol did not affect phase I metabolism of atorvastatin

  16. United States: refrigeration industry blows hot

    International Nuclear Information System (INIS)

    Crawford, J.

    1997-01-01

    In the framework of the Kyoto convention on global warming, the american refrigeration industries have undertaken several organizations and contacts with governments and agencies in order to explain the real issues concerning the effects of refrigerant utilization in refrigerating machines on the greenhouse effect, taking into consideration the commercial impact that a ban on certain refrigerants could have on the industry's business. They argue that HFC utilization in this industry is fundamentally non-emissive and that important improvements have been realized concerning tightness and energy consumption

  17. Structure and property evaluation of a vacuum plasma sprayed nanostructured tungsten-hafnium carbide bulk composite

    International Nuclear Information System (INIS)

    Rea, K.E.; Viswanathan, V.; Kruize, A.; Hosson, J.Th.M. de; O'Dell, S.; McKechnie, T.; Rajagopalan, S.; Vaidyanathan, R.; Seal, S.

    2008-01-01

    Vacuum plasma spray (VPS) forming of tungsten-based metal matrix nanocomposites (MMCs) has shown to be a cost effective and time saving method for the formation of bulk monolithic nanostructured thermo-mechanical components. Spray drying of powder feedstock appears to have a significant effect on the improved mechanical properties of the bulk nanocomposite. The reported elastic modulus of the nanocomposite nearly doubles due to the presence of HfC nano particulates in the W matrix. High resolution transmission electron microscopy (HRTEM) revealed the retention of nanostructures at the select process conditions and is correlated with the enhanced mechanical properties of the nanocomposite

  18. A study of the radiative forcing and global warming potentials of hydrofluorocarbons

    International Nuclear Information System (INIS)

    Zhang Hua; Wu Jinxiu; Lu Peng

    2011-01-01

    We developed a new radiation parameterization of hydrofluorocarbons (HFCs), using the correlated k-distribution method and the high-resolution transmission molecular absorption (HITRAN) 2004 database. We examined the instantaneous and stratospheric adjusted radiative efficiencies of HFCs for clear-sky and all-sky conditions. We also calculated the radiative forcing of HFCs from preindustrial times to the present and for future scenarios given by the Intergovernmental Panel on Climate Change Special Report on Emission Scenarios (SRES, in short). Global warming potential and global temperature potential were then examined and compared on the basis of the calculated radiative efficiencies. Finally, we discuss surface temperature changes due to various HFC emissions.

  19. MO-HF-C alloy composition

    International Nuclear Information System (INIS)

    Whelan, E.P.; Kalns, E.

    1987-01-01

    This patent describes, as an article of manufacture, a cast ingot of a molybdenum-hafnium-carbon alloy consisting essentially by weight of about 0.6% to about 1% Hf, about 0.045% to about 0.08% C, and the balance essentially molybdenum. The amount of Hf and C present are substantially stoichiometric with respect to HfC and within about +-15% of stoichiometry. The ingot is characterized in that it has a substantially less tendency to crack compared to alloys containing Hf in excess of about 1% by weight and carbon in excess of 0.08% by weight, without substantial diminution in strength properties of the alloy

  20. Experimental results for hydrocarbon refrigerant vaporization inside brazed plate heat exchangers at high pressure

    DEFF Research Database (Denmark)

    Desideri, Adriano; Ommen, Torben Schmidt; Wronski, Jorrit

    2016-01-01

    fluids at typical working conditions of ORC systems for low temperature waste heat recovery (WHR) applications. Based on these premises, a novel testrig has been recently designed and built at the Technical University of Denmark to simulate the evaporating condition occurring in a small capacity ORC...... power unit. In this contribution the preliminary experimental results obtained from the first experimental campaign carried out on the rig are reported. HFC-134a was selected as working fluid. The experiments were carried out at saturation temperature of 60, 70 and 80 °C and inlet and outlet qualities...

  1. An experimental analysis of flow boiling and pressure drop in a brazed plate heat exchanger for organic Rankine cycle power systems

    DEFF Research Database (Denmark)

    Desideri, Adriano; Zhang, Ji; Kærn, Martin Ryhl

    2017-01-01

    Organic Rankine cycle power systems for low quality waste heat recovery applications can play a major role in achieving targets of increasing industrial processes efficiency and thus reducing the emissions of greenhouse gases. Low capacity organic Rankine cycle systems are equipped with brazed...... and pressure drop during vaporization at typical temperatures for low quality waste heat recovery organic Rankine cycle systems are presented for the working fluids HFC-245fa and HFO-1233zd. The experiments were carried out at saturation temperatures of 100°C, 115°C and 130°C and inlet and outlet qualities...

  2. World cheating on the carbon market

    International Nuclear Information System (INIS)

    James, O.

    2010-01-01

    According to several non-governmental organizations, some industrial producers take advantage of a flaw in one of the carbon market mechanisms set up by the Kyoto protocol. These industrialists, mainly from China and India, are involved in the production of HCFC22 refrigerants, and make a substantial profit by artificially generating more greenhouse gases (HFC23) than necessary, then destroying them in order to collect carbon credits which they sell on the carbon market. Explanations about the cheat, details about companies and banks involved in the system, review of past trickeries in carbon quotas, and ways to improve the carbon market are presented

  3. Air emissions in France overseas substances involved in the acidification, eutrophication, photochemical and greenhouse effect processes; Emissions dans l'air en France Outre-mer substances impliquees dans les phenomenes d'acidification, de photochimie et d'effet de serre

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-06-01

    The concerned substances are SO{sub 2} and NO{sub x} for the DOM (overseas departments); the six direct greenhouse gases (CO{sub 2}, CH{sub 4}, N{sub 2}O, HFC, PFC and SF{sub 6}) and non direct gases (VOC, CO, NO{sub x}, and SO{sub 2}) for the overseas departments and territories; the NH{sub 3} emissions for the eutrophication. Emissions are presented by the mean of charts. (A.L.B.)

  4. Denmark's national inventory report 2008 - Submitted under the United Nations framework convention on climate change, 1990-2006. Emission inventories

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, Ole-Kenneth; Lyck, E.; Hjorth Mikkelsen, M. (and others)

    2008-05-15

    This report is Denmark's National Inventory Report reported to the Conference of the Parties under the United Nations Framework Convention on Climate Change (UNFCCC) due by 15 April 2008. The report contains information on Denmark's inventories for all years' from 1990 to 2006 for CO{sub 2}, CH{sub 4}, N{sub 2}O, HFC{sub s}, PFC{sub s} and SF{sub 6}, CO, NMVOC, SO{sub 2}. (au)

  5. An inexpensive and fast method for infiltration coating of complex geometry matrices for ISOL production target applications

    International Nuclear Information System (INIS)

    Kawai, Y.; Alton, G.D.; Bilheux, J.-C.

    2005-01-01

    An inexpensive, fast, and close to universal infiltration coating technique has been developed for fabricating fast diffusion-release ISOL targets. Targets are fabricated by deposition of finely divided (∼1μm) compound materials in a paint-slurry onto highly permeable, complex structure reticulated-vitreous-carbon-foam (RVCF) matrices, followed by thermal heat treatment. In this article, we describe the coating method and present information on the physical integrity, uniformity of deposition, and matrix adherence of SiC, HfC and UC 2 targets, destined for on-line use as targets at the Holifield Radioactive Ion Beam Facility (HRIBF)

  6. A review of chromium, molybdenum, and tungsten alloys

    International Nuclear Information System (INIS)

    Klopp, W.D.

    1975-01-01

    The mechanical properties of chromium, molybdenum, and tungsten alloys are reviewed, with particular emphasis on high-temperature strength and low-temperature ductility. Precipitate strengthening is highly effective at 0.4-0.8 Tsub(m) in these metals, with HfC being most effective in tungsten and molybdenum, and Ta(B,C) most effective in chromium. Low-temperature ductility can be improved by alloying to promote rhenium ductilizing or solution softening. The low-temperature mechanical properties of these alloys appear related to electronic interactions rather than to the usual metallurgical considerations. (Auth.)

  7. Estimation of Freezing Point of Hydrocarbon and Hydrofluorocarbon Mixtures for Mixed Refrigerant jt Cryocooler

    Science.gov (United States)

    Hwang, G.; Lee, J.; Jeong, S.

    2010-04-01

    Estimating the freezing point of refrigerant is an essential part in designing an MR JT (Mixed refrigerant Joule-Thomson) cryocooler to prevent itself from clogging and to operate with stability. There were researches on estimating freezing point, but some of them resulted in the wrong prediction of clogging. In this paper, the freezing point of the MR is precisely estimated with caution of clogging. The solubility of HC (hydrocarbon) and HFC (hydrofluorocarbon) mixture components are obtained with their activity coefficients, which represent the molecular interaction among the components. The freezing points of the MR JT cryocooler are systematically investigated in the operating temperature range from 70 K to 90 K.

  8. Properties of carbides and hard metals. Pt. 1

    International Nuclear Information System (INIS)

    Nazare, S.; Ondracek, G.

    1977-01-01

    Measurements of the electrical resistivity and of the Young modulus are reported for the carbides TiC, HfC, NbC, and TaC. The investigations included the solid solutions TiC-HfC, HfC-NbC, TaC-NbC, and TiC-NbC. For the solid solutions, measurements of the thermal expansion in the range 293-1173 K are also reported. All the samples were prepared by hot pressing of the commercial powders in graphite dies. The chemical composites are also presented. The measurement results are shown in figures. (GSC) [de

  9. Department of the Navy Justification of Estimates for Fiscal Year 1988/1989 Submitted to Congress. Procurement. Other Procurement, Navy.

    Science.gov (United States)

    1987-01-01

    7 7ZD- AISI 9721 PffARTMENT OF THE NAVY JUffjA~j HFC S A FO L/L U I (NAUil) WASHINC ON C JAN&LNCLASS IFI ED F/G 5/1 NL I M2 I12 5 coo~ LIFJ -I LII...0 4 4)-s.. -4 4J C: 00 + ,. LI0a 4)00&.4. 00a 4)CA.V f0 4- > 1 - 1 404- 4JLA. 0- =. i.- >, 0h0 a0 cn 4 (40 s.4 > 4 24*~ (-A *.eZ---. 0. .. ., tv 4140

  10. Sister chromatid exchanges and micronuclei analysis in lymphocytes of men exposed to simazine through drinking water.

    Science.gov (United States)

    Suárez, Susanna; Rubio, Arantxa; Sueiro, Rosa Ana; Garrido, Joaquín

    2003-06-06

    In some cities of the autonomous community of Extremadura (south-west of Spain), levels of simazine from 10 to 30 ppm were detected in tap water. To analyse the possible effect of this herbicide, two biomarkers, sister chromatid exchanges (SCE) and micronuclei (MN), were used in peripheral blood lymphocytes from males exposed to simazine through drinking water. SCE and MN analysis failed to detect any statistically significant increase in the people exposed to simazine when compared with the controls. With respect to high frequency cells (HFC), a statistically significant difference was detected between exposed and control groups.

  11. Recoilless fractions calculated with the nearest-neighbour interaction model by Kagan and Maslow

    Science.gov (United States)

    Kemerink, G. J.; Pleiter, F.

    1986-08-01

    The recoilless fraction is calculated for a number of Mössbauer atoms that are natural constituents of HfC, TaC, NdSb, FeO, NiO, EuO, EuS, EuSe, EuTe, SnTe, PbTe and CsF. The calculations are based on a model developed by Kagan and Maslow for binary compounds with rocksalt structure. With the exception of SnTe and, to a lesser extent, PbTe, the results are in reasonable agreement with the available experimental data and values derived from other models.

  12. JPRS Report Science & Technology Japan Future Prospects of FA-From FA to IMS

    Science.gov (United States)

    1989-12-04

    of FA Investment (Large Companies) a) m d) m 5000fI~ljl|S 1 m± ¥-1$ 500~1000t| 300~500(f 1000~3000ft i) £ÜÜ 0i!§£3^ SWOT # H^fc3S j) k) 1...is a method conceived by Toyota Motors, now widely understood throughout the world. Such information as the production volume, time, method and...T. Suzuki Toyota Motor Corp. Y. Tatsue AIST, Mechanical Engineering Laboratory K. Togino Komatsu Ltd. H. Torii Nihon Keizai Shimbun Editorial

  13. Dissociative properties of 1,1,1,2-tetrafluoroethane obtained by computational chemistry

    Science.gov (United States)

    Hayashi, Toshio; Ishikawa, Kenji; Sekine, Makoto; Hori, Masaru

    2018-06-01

    The electronic properties and dissociative channels of the alternative to the CCl2F2 (CFC-12) refrigerant, 1,1,1,2-tetrafluoroethane (HFC-134a) with a low global warming potential (GWP, 1430), were revealed by computational chemistry. The results show that CF3 + and CHF2 + ions are mainly produced by ionization. The CF3CH2 + ion is produced by ion pair formation and by direct ionization in the energy region higher than approximately 15 eV, but also in small amounts by the ionization of the dissociated CF3CH2 radical. This information is useful for etching process engineers in leading-edge semiconductor manufacturing.

  14. Broadband network selection issues

    Science.gov (United States)

    Leimer, Michael E.

    1996-01-01

    Selecting the best network for a given cable or telephone company provider is not as obvious as it appears. The cost and performance trades between Hybrid Fiber Coax (HFC), Fiber to the Curb (FTTC) and Asymmetric Digital Subscriber Line networks lead to very different choices based on the existing plant and the expected interactive subscriber usage model. This paper presents some of the issues and trades that drive network selection. The majority of the Interactive Television trials currently underway or planned are based on HFC networks. As a throw away market trial or a short term strategic incursion into a cable market, HFC may make sense. In the long run, if interactive services see high demand, HFC costs per node and an ever shrinking neighborhood node size to service large numbers of subscribers make FTTC appear attractive. For example, thirty-three 64-QAM modulators are required to fill the 550 MHz to 750 MHz spectrum with compressed video streams in 6 MHz channels. This large amount of hardware at each node drives not only initial build-out costs, but operations and maintenance costs as well. FTTC, with its potential for digitally switching large amounts of bandwidth to an given home, offers the potential to grow with the interactive subscriber base with less downstream cost. Integrated telephony on these networks is an issue that appears to be an afterthought for most of the networks being selected at the present time. The major players seem to be videocentric and include telephony as a simple add-on later. This may be a reasonable view point for the telephone companies that plan to leave their existing phone networks untouched. However, a phone company planning a network upgrade or a cable company jumping into the telephony business needs to carefully weigh the cost and performance issues of the various network choices. Each network type provides varying capability in both upstream and downstream bandwidth for voice channels. The noise characteristics

  15. EKONOMİK ÖZGÜRLÜKLERDEKİ YAKINSAMANIN HALDANE-HALL YAKLAŞIMI İLE ÖLÇÜMÜ (THE MEASUREMENT OF CONVERGENCE OF ECONOMIC FREEDOMS WITH HALDANE-HALL APPROACH

    Directory of Open Access Journals (Sweden)

    Merter AKINCI

    2014-04-01

    Full Text Available ÖZ: Son otuz yıldan bu yana yaşanan en önemli gelişmelerden biri, hızlanan küreselleşme hareketleri kapsamında liberal iktisadi düşünce ve politikaların dünya genelinde yayılması olmuştur. Özellikle neo-liberal hareketler ile birlikte iktisadi bakımdan kapsamı genişletilen özgürlükçü akımlar, toplumsal yapılanma tarafından vazgeçilmez bir unsur olmuş ve ekonomik serbesti, refah gücünün artırılabilmesi amacıyla makro iktisadi gelişmelerin ana eksenini oluşturmuştur. Dolayısıyla bu çalışmada, gelişmekte olan ve azgelişmiş ülkelerin gelişmiş ülkelere ekonomik özgürlükler bakımından yaklaşıp yaklaşmadıkları yeni bir yöntem olan Haldane-Hall Yakınsama Analizi ile incelenmiştir. Haldane-Hall yakınsama analizi sonuçları; Arjantin, Belarus, Bolivya, Bulgaristan, Çin, Ekvador, Mısır, El Salvador, Hindistan, Meksika, Papua Yeni Gine, Romanya, Senegal, Tayland ve Türkiye’deki ekonomik özgürlük süreçlerinin gelişmiş ülkelere yakınsadığını; buna karşın Kongo Cumhuriyeti, Gana, Irak, Ürdün, Libya, Moldova, Fas, Sudan, Svaziland, Vietnam, Yemen, Bangladeş, Burkina Faso, Çad, Demokratik Kongo Cumhuriyeti, Gambiya, Gine, Madagaskar, Mali, Mozambik, Sierra Leone ve Uganda’da ise ekonomik özgürlükler bakımından ıraksama olgusunun gündeme geldiğini ortaya koymuştur. Anahtar Kelimeler: Ekonomik Özgürlükler, Yakınsama, Haldane-Hall Yaklaşımı. ABSTRACT: One of the most important developments in the last thirty years is the expansion of liberal economic thought and policies in terms of accelerating globalization movements. Libertarian movements the scope of which has been extended with regards to economics and especially neo-liberal movements became an irreplaceable element of social set-up and their economic liberation formed the main core of the developments of macroeconomics with the aim of increasing the welfare level. In this study, therefore, whether

  16. Covering Post-Conflict Elections: Challenges for the Media in Central Africa Wahlberichterstattung in Post-Konflikt-Phasen: Herausforderungen für die Medien in Zentralafrika

    Directory of Open Access Journals (Sweden)

    Marie-Soleil Frère

    2011-01-01

    Full Text Available In the past ten years, elections were held in six countries of Central Africa experiencing “post-conflict” situations. The polls that took place in Burundi (2005, the Central African Republic (2005, the Democratic Republic of the Congo (2006, Congo-Brazzaville (2002, 2007, Chad (1996, 2001, 2006 and Rwanda (2003 were crucial for peace-building. In some cases, they were widely supported and supervised by the international community, being considered the last step of a peace process and the first step toward establishing a truly representative “post-conflict” regime. The media were expected to play a large part in supporting these elections, both to inform the citizens, so they could make an educated choice, and to supervise the way the electoral administration was organizing the polls. This paper attempts to show the many challenges faced by the media while covering these post-conflict electoral processes. In a context of great political tension, in which candidates are often former belligerents who have just put down their guns to go to the polls, the media operate in an unsafe and economically damaged environment, suffering from a lack of infrastructure, inadequate equipment and untrained staff. Given those constraints, one might wonder if the media should be considered actual democratic tools in Central Africa or just gimmicks in a “peace-building kit” (including “free and fair” elections, multipartism and freedom of the press with no real impact on the democratic commitment of the elite or the political participation of the population.In den letzten zehn Jahren wurden in sechs zentralafrikanischen Ländern, die sich in einer Post-Konflikt-Phase befanden, Wahlen abgehalten. Die Wahlgänge in Burundi (2005, der Zentralafrikanischen Republik (2005, der Demokratischen Republik Kongo (2006, Kongo-Brazzaville (2002, 2007, dem Tschad (1996, 2001, 2006 und Ruanda (2003 waren entscheidend für die Friedenskonsolidierung. Einige dieser

  17. Anemia and Micronutrient Status of Women of Childbearing Age and Children 6–59 Months in the Democratic Republic of the Congo

    Directory of Open Access Journals (Sweden)

    Sarah Harvey-Leeson

    2016-02-01

    Full Text Available Little is known about the micronutrient status of women and children in the Democratic Republic of the Congo, which is critical for the design of effective nutrition interventions. We recruited 744 mother-child pairs from South Kivu (SK and Kongo Central (KC. We determined hemoglobin (Hb, serum zinc, vitamin B12, folate, ferritin, soluble transferrin receptor (sTfR, retinol binding protein (RBP, C-reactive protein, and α-1 acid glycoprotein concentrations. Anemia prevalence was determined using Hb adjusted for altitude alone and Hb adjusted for both altitude and ethnicity. Anemia prevalence was lower after Hb adjustment for altitude and ethnicity, compared to only altitude, among women (6% vs. 17% in SK; 10% vs. 32% in KC, children 6–23 months (26% vs. 59% in SK; 25% vs. 42% in KC, and children 24–59 months (14% vs. 35% in SK; 23% vs. 44% in KC, respectively. Iron deficiency was seemingly higher with sTfR as compared to inflammation-adjusted ferritin among women (18% vs. 4% in SK; 21% vs. 5% in KC, children 6–23 months (51% vs. 14% in SK; 74% vs. 10% in KC, and children 24–59 months (23% vs. 4% in SK; 58% vs. 1% in KC. Regardless of indicator, iron deficiency anemia (IDA never exceeded 3% in women. In children, IDA reached almost 20% when sTfR was used but was only 10% with ferritin. Folate, B12, and vitamin A (RBP deficiencies were all very low (<5%; RBP was 10% in children. The prevalence of anemia was unexpectedly low. Inflammation-adjusted zinc deficiency was high among women (52% in SK; 58% in KC, children 6–23 months (23% in SK; 20% in KC, and children 24–59 months (25% in SK; 27% in KC. The rate of biochemical zinc deficiency among Congolese women and children requires attention.

  18. Yabani Baklagil Bitkilerinden, Mikrobiyal Gübre Olarak Kullanılan Rhizobium Spp. Bakterilerinin İzolasyonu

    Directory of Open Access Journals (Sweden)

    Hatice Öğütcü

    2014-05-01

    Full Text Available Araştırmamızda kullanılan yabani baklagil bitkileri ( Medicago sativa, M.lupulina ve M. varia Erzurum iline ait yüksek rakımlı (2000-2500m bölgelerden (Palandöken dağı, Alibaba dağı, Turnagöl dağı, Hasanbaba dağı, Eğerli dağı, Yıldırım dağı, Çubuklu dağı, Deveboynu mevkii, Kayakyolu mevkii, Telsizler tepesi ve Dumlu tepesi Haziran ve Temmuz aylarında toplandı. Bu bitkilerden elde edilen nodüller steril edilerek YMA (Yeast Mannitol Agar plaklarına çizgi ekim yapıldı ve petriler 28+1ºC’de 3-5 gün süreyle inkübasyona bırakıldı. İnkübasyon süresi sonunda oluşan tipik koloniler oluşturan (beyaz, saydam veya hafif mat, mukozlu, yuvarlak, kabarık 39 izolat seçilerek yatık YMA tüplerine aktarıldı ve buzdolabında +4ºC’de muhafaza edildi. Sonraki aşamada bu izolatlar sitolojik ve biyokimyasal analizlerle tanımlanmaya çalışıldı. Bu amaçla izolatlar; Brom Thymol Mavili ve Kongo Kırmızılı YMA’da üreme, gram özelliği, hareket, katalaz ve oksidaz testlerine tabi tutularak değerlendirildi. Yapılan sitolojik ve biyokimyasal analizler sonucunda elde edilen 39 izolatın 28’inin Rhizobium spp. olduğu tespit edildi.

  19. Passive Two-Phase Cooling of Automotive Power Electronics: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, G.; Jeffers, J. R.; Narumanchi, S.; Bennion, K.

    2014-08-01

    Experiments were conducted to evaluate the use of a passive two-phase cooling strategy as a means of cooling automotive power electronics. The proposed cooling approach utilizes an indirect cooling configuration to alleviate some reliability concerns and to allow the use of conventional power modules. An inverter-scale proof-of-concept cooling system was fabricated, and tests were conducted using the refrigerants hydrofluoroolefin HFO-1234yf and hydrofluorocarbon HFC-245fa. Results demonstrated that the system can dissipate at least 3.5 kW of heat with 250 cm3 of HFC-245fa. An advanced evaporator design that incorporates features to improve performance and reduce size was conceived. Simulation results indicate its thermal resistance can be 37% to 48% lower than automotive dual side cooled power modules. Tests were also conducted to measure the thermal performance of two air-cooled condensers--plain and rifled finned tube designs. The results combined with some analysis were then used to estimate the required condenser size per operating conditions and maximum allowable system (i.e., vapor and liquid) temperatures.

  20. Masking of Time-Frequency Patterns in Applications of Passive Underwater Target Detection

    Directory of Open Access Journals (Sweden)

    Jüri Sildam

    2010-01-01

    Full Text Available Spectrogram analysis of acoustical sounds for underwater target classification is utilized when loud nonstationary interference sources overlap with a signal of interest in time but can be separated in time-frequency (TF domain. We propose a signal masking method which in a TF plane combines local statistical and morphological features of the signal of interest. A dissimilarity measure D of adjacent TF cells is used for local estimation of entropy H, followed by estimation of ΔH=Htc−Hfc entropy difference, where Hfc is calculated along the time axis at a mean frequency fc and Htc is calculated along the frequency axis at a mean time tc of the TF window, respectively. Due to a limited number of points used in ΔH estimation, the number of possible ΔH values, which define a primary mask, is also limited. A secondary mask is defined using morphological operators applied to, for example, H and ΔH. We demonstrate how primary and secondary masks can be used for signal detection and discrimination, respectively. We also show that the proposed approach can be generalized within the framework of Genetic Programming.