Depleted Uranium Hexafluoride Management Program. The technology assessment report for the long-term management of depleted uranium hexafluoride. Volume 1

Energy Technology Data Exchange (ETDEWEB)

Zoller, J.N.; Rosen, R.S.; Holliday, M.A. [and others

1995-06-30

With the publication of a Request for Recommendations and Advance Notice of Intent in the November 10, 1994 Federal Register, the Department of Energy initiated a program to assess alternative strategies for the long-term management or use of depleted uranium hexafluoride. This Request was made to help ensure that, by seeking as many recommendations as possible, Department management considers reasonable options in the long-range management strategy. The Depleted Uranium Hexafluoride Management Program consists of three major program elements: Engineering Analysis, Cost Analysis, and an Environmental Impact Statement. This Technology Assessment Report is the first part of the Engineering Analysis Project, and assesses recommendations from interested persons, industry, and Government agencies for potential uses for the depleted uranium hexafluoride stored at the gaseous diffusion plants in Paducah, Kentucky, and Portsmouth, Ohio, and at the Oak Ridge Reservation in Tennessee. Technologies that could facilitate the long-term management of this material are also assessed. The purpose of the Technology Assessment Report is to present the results of the evaluation of these recommendations. Department management will decide which recommendations will receive further study and evaluation. These Appendices contain the Federal Register Notice, comments on evaluation factors, independent technical reviewers resumes, independent technical reviewers manual, and technology information packages.

Depleted Uranium Hexafluoride Management Program. The technology assessment report for the long-term management of depleted uranium hexafluoride. Volume 1

International Nuclear Information System (INIS)

Zoller, J.N.; Rosen, R.S.; Holliday, M.A.

1995-01-01

With the publication of a Request for Recommendations and Advance Notice of Intent in the November 10, 1994 Federal Register, the Department of Energy initiated a program to assess alternative strategies for the long-term management or use of depleted uranium hexafluoride. This Request was made to help ensure that, by seeking as many recommendations as possible, Department management considers reasonable options in the long-range management strategy. The Depleted Uranium Hexafluoride Management Program consists of three major program elements: Engineering Analysis, Cost Analysis, and an Environmental Impact Statement. This Technology Assessment Report is the first part of the Engineering Analysis Project, and assesses recommendations from interested persons, industry, and Government agencies for potential uses for the depleted uranium hexafluoride stored at the gaseous diffusion plants in Paducah, Kentucky, and Portsmouth, Ohio, and at the Oak Ridge Reservation in Tennessee. Technologies that could facilitate the long-term management of this material are also assessed. The purpose of the Technology Assessment Report is to present the results of the evaluation of these recommendations. Department management will decide which recommendations will receive further study and evaluation. These Appendices contain the Federal Register Notice, comments on evaluation factors, independent technical reviewers resumes, independent technical reviewers manual, and technology information packages

Morse-Morse-Spline-Van der Waals intermolecular potential suitable for hexafluoride gases

International Nuclear Information System (INIS)

Coroiu, Ilioara

2004-01-01

Several effective isotopic pair potential functions have been proposed to characterize the bulk properties of quasispherical molecules, in particular the hexafluorides, but none got a success. Unfortunately, these potentials have repulsive walls steeper than those which describe the hexafluorides. That these intermolecular potentials are not quite adequate is shown by the lack of complete agreement between theory and experiment even for the rare gases. Not long ago, R. A. Aziz et al. have constructed a Morse-Morse-Spline-Van der Waals (MMSV) potential. The MMSV potential incorporates the determination of C 6 dispersion coefficient and it reasonably correlates second virial coefficients and viscosity data of sulphur hexafluoride at the same time. None of the potential functions previously proposed in literature could predict these properties simultaneously. We calculated the second virial coefficients and a large number of Chapman-Cowling collision integrals for this improved intermolecular potential, the MMSV potential. The results were tabulated for a large reduced temperature range, kT/ε from 0.1 to 100. The treatment was entirely classical and no corrections for quantum effects were made. The higher approximations to the transport coefficients and the isotopic thermal diffusion factor were also calculated and tabulated for the same range. In this paper we present the evaluation of the uranium hexafluoride potential parameters for the MMSV intermolecular potential. To find a single set of potential parameters which could predict all the transport properties (viscosity, thermal conductivity, self diffusion, etc.), as well as the second virial coefficients, simultaneously, the method suggested by Morizot and a large assortment of literature data were used. Our results emphasized that the Morse-Morse-Spline-Van der Waals potential have the best overall predictive ability for gaseous hexafluoride data, certain for uranium hexafluoride. (author)

Spectroscopy of hexafluorides with an odd number of electrons

International Nuclear Information System (INIS)

Boudon, V.

1995-05-01

From a theoretical point of view, a tensorial formalism adapted to the study of molecules or octahedral ions with a half-integer angular momentum has been developed for the first time. We have used here the method of projective representations, more consistent than that of double groups. A complete set of coupling coefficients and formulas, as well as the corresponding computing programs have been elaborated. This has firstly allowed us to write a simple model describing the vibronic structure of colored hexafluorides. Then, some applications of this formalism to the study of ro-vibronic couplings of XY 6 molecules in a fourfold degenerate electronic state have been considered, especially concerning operators associated to dynamic Jahn-Teller effect. From an experimental point of view, we have considered IrF 6 , for which we have mastered the synthesis, purification and conservation processes. A first study at low resolution (absorption and Raman scattering) has been performed for this molecule. We have then set up two high resolution spectroscopic devices in the visible region (saturated absorption - tested with an iodine cell- and simple absorption with multiple pass). These especially use a dye laser. They should now allow the spectroscopy of the visible band of IrF 6 in order to resolve for the first time its fine rotational structure. (author)

Analytical standards for accountability of uranium hexafluoride - 1972

International Nuclear Information System (INIS)

Anon.

1976-01-01

An analytical standard for the accountability of uranium hexafluoride is presented that includes procedures for subsampling, determination of uranium, determination of metallic impurities and isotopic analysis by gas and thermal ionization mass spectrometry

Sulfur hexafluoride purification from mixtures with air: a process feasibility study

International Nuclear Information System (INIS)

Perona, J.J.; Watson, J.S.

1979-10-01

Studies were made of the purification of SF 6 vapor contaminated with air for application at the Holifield Heavy-Ion Research Facility. Liquefaction appears to be a good method for recovering about 90% of the SF 6 if it is badly contaminated (15% air), and an even greater fraction can be recovered from mixtures containing less air. In cases where liquefaction is insufficient by itself, adsorption of SF 6 on activated carbon at -50 0 F is promising. Two carbon beds, each containing about 500 lb of carbon, should be sufficient. The refrigeration system for liquefaction and adsorption would have a capacity of about 2 tons. As an alternative, the use of molecular sieves to trap out the air was investigated, but such a bed would require at least 15,000 lb of molecular sieves and very long cycle times. A large-scale desublimer was also investigated and appears workable, but it would require some development effort before the design could proceed with confidence

Process for producing uranium oxide rich compositions from uranium hexafluoride

International Nuclear Information System (INIS)

DeHollander, W.R.; Fenimore, C.P.

1978-01-01

Conversion of gaseous uranium hexafluoride to a uranium dioxide rich composition in the presence of an active flame in a reactor defining a reaction zone is achieved by separately introducing a first gaseous reactant comprising a mixture of uranium hexafluoride and a reducing carrier gas, and a second gaseous reactant comprising an oxygen-containing gas. The reactants are separated by a shielding gas as they are introduced to the reaction zone. The shielding gas temporarily separates the gaseous reactants and temporarily prevents substantial mixing and reacting of the gaseous reactants. The flame occurring in the reaction zone is maintained away from contact with the inlet introducing the mixture to the reaction zone. After suitable treatment, the uranium dioxide rich composition is capable of being fabricated into bodies of desired configuration for loading into nuclear fuel rods. Alternatively, an oxygen-containing gas as a third gaseous reactant is introduced when the uranium hexafluoride conversion to the uranium dioxide rich composition is substantially complete. This results in oxidizing the uranium dioxide rich composition to a higher oxide of uranium with conversion of any residual reducing gas to its oxidized form

Preparation of sodium fluoride agglomerates for selective adsorption of uranium hexafluoride (U F6)

International Nuclear Information System (INIS)

Castro, A.R.; Maximiano, C.; Shimba, R.; Silva, E.R.F.

1995-01-01

Uranium hexafluoride (U F 6 ) and Sodium Fluoride (NaF) reacts reversibly to form a solid complex. Such reversibility accounts for the great interest in using Sodium Fluoride (NaF) to separate Uranium Hexafluoride (U F 6 ) from other gases. Therefore a chemical trap offers an alternative to the cryogenic trapping device. (author). 3 refs, 1 fig, 4 tabs

Processing device for gaseous waste containing uranium hexafluoride

International Nuclear Information System (INIS)

Hirosawa, Jun-ichi.

1985-01-01

Purpose: To enable to detect the inactivation of chemical traps thereby reduce the amount of adsorbents. Constitution: Two chemical traps are disposed in series and γ-detector for detecting γ-rays generated from U-235 in hexafluoride is disposed to the outer surface of a pipeway connecting these two chemical traps. Further, chemical traps are adapted to be swtichable between the first stage and the second stage thereof by the ON-OFF operation of a valve. Then, by determining γ-rays from U-235 at the pipeway downstream from the gas exit of the chemical traps, the counted value for the γ-rays is substantially at the background level so long as the chemical trap has an adsorbing performance for uranium hexafluoride. Then, since the γ-ray counted value is increased at the step upon inactivation of the chemical trap, the inactivation of the trap can be detected. (Yoshino, Y.)

Cost-effectiveness of safety measures applying to uranium hexafluoride transportation in France

International Nuclear Information System (INIS)

Hubert, P.; Pages, P.; Auguin, B.

1983-01-01

This paper addresses the problem of uranium hexafluoride transportation by truck and train. It consists of a probabilistic risk assessment of the potential hazards to the public that can arise from the traffice that will take place in France in 1990. The specificity of UF 6 is that it presents both chemical and radiological hazards. But, whatever the transported material, road traffic entails a risk of its own. Thus three kinds of risk are assessed for natural, depleted and enriched uranium hexafluoride. These assessments are the basis of a cost-effectiveness analysis which deals with such safety measures as using a protective overpack, avoiding populated area and escorting the trucks. The results presented here are based upon research supported by the C.E.A. (Commissariat a l'Energie Atomique). It is linked to a more general program of experiments and theoretical analyses on package safety and accidental releases for uranium hexafluoride. 7 references, 2 figures, 4 tables

Method for separation of uranium hexafluoride by specially activated carbons

International Nuclear Information System (INIS)

Bannasch, W.

1976-01-01

The present invention deals with the separation of urainium hexafluoride from gas streams on special activated carbon which can be released during an accident in nuclear plants. Those plants are concerned here in which as a rule uranium hexafluoride is handled in liquid aggregate state. The patent claims deal with the adsorption of UF 6 from gas mixtures in the temperature region of 70-200 0 C and the application of UF 6 adsorbing activated carbon of a certain grain based on petroleum and/or weight % and with a asch content of 4 to 6 weigt % and with a benzol yield of 50-60g benzene /100g activated carbon. (GG) [de

Helium and Sulfur Hexafluoride in Musical Instruments

Science.gov (United States)

Forinash, Kyle; Dixon, Cory L.

2014-01-01

The effects of inhaled helium on the human voice were investigated in a recent article in "The Physics Teacher." As mentioned in that article, demonstrations of the effect are a popular classroom activity. If the number of YouTube videos is any indication, the effects of sulfur hexafluoride on the human voice are equally popular.…

Test emission of uranium hexafluoride in atmosphere. Results interpretation

International Nuclear Information System (INIS)

Crabol, B.; Deville-Cavelin, G.

1989-01-01

To permit the modelization of gaseous uranium hexafluoride behaviour in atmosphere, a validation test has been executed the 10 April 1987. The experimental conditions, the main results and a comparison with a diffusion model are given in this report [fr

F19 relaxation in non-magnetic hexafluorides

International Nuclear Information System (INIS)

Rigny, P.

1969-01-01

The interesting properties of the fluorine magnetic resonance in the hexafluorides of molybdenum, tungsten and uranium, are very much due to large anisotropies of the chemical shift tensors. In the solid phases these anisotropies, the values of which are deduced from line shape studies, allow one to show that the molecules undergo hindered rotations about the metal atom. The temperature and frequency dependence of the fluorine longitudinal relaxation times shows that the relaxation is due to the molecular motion. The dynamical parameters of this motion are then deduced from the complete study of the fluorine relaxation in the rotating frame. In the liquid phases, the existence of anisotropies allows an estimation of the different contributions to the relaxation. In particular, the frequency and temperature dependence of the relaxation shows it to be dominated by the spin-rotation interaction. We have shown that the strength of this interaction can be deduced from the chemical shifts, and the angle through which the molecule rotates quasi-freely can be determined. In the hexafluorides, this angle is roughly one radian at 70 C, and with the help of this value, the friction coefficients which describe the intermolecular interactions are discussed. (author) [fr

Reaction between molybdenum hexafluoride and carboxylic acids

International Nuclear Information System (INIS)

Shustov, L.D.; Nikolenko, L.N.; Senchenkova, T.M.

1983-01-01

Trifluoromethyl derivatives of pyridine, imidazole and difluoromethane are synthesized during interaction of MoF 6 surplUs (190-210 deg) with nicotine-isomicotine-, 2,6-pyridinedicarboxylic-, 4,5-imidazoledicarboxyclic- and diffluoroacetic acids. The yield of trifluoromethyl derivatives attains 84%. Molybdenum hexafluoride offers some advantages in comparisoo with toxic SF 4 . MoF 6 toxicity is low; leakage of MoF 6 vapors is easily detected

Uranium hexafluoride and uranyl nitrate. Ionometric determination of bromine

International Nuclear Information System (INIS)

Anon.

Bromine was determined in uranium hexafluoride. The method is suitable for determining 2 to 20 ppm with respect to uranium. Bromides are oxidized by potassium permanganate to give bromine which is extracted into carbon tetrachloride, reduced by ascorbic acid and determined by ionometry [fr

Reaction between uranium hexafluoride and trimethylsilylhalides

Energy Technology Data Exchange (ETDEWEB)

Brown, D; Berry, J A [UKAEA Atomic Energy Research Establishment, Harwell. Chemistry Div.; Holloway, J H; Staunton, G M [Leicester Univ. (UK). Dept. of Chemistry

1938-07-01

Reactions involving 1.1:1 molar ratios of uranium hexafluoride to either trimethylsilylchloride or trimethylsilylbromide in halocarbon solutions yield ..beta..-UF/sub 5/ at room temperature. With 2 mol equivalents of trimethylsilylchloride the product is UF/sub 4/. The reactions appear to proceed via the intermediate formation of unstable brown uranium(VI) chloride and bromide fluorides. Calculations show that UClF/sub 5/ and UCl/sub 2/F/sub 4/ are thermodynamically unstable with respect to the loss of chlorine at room temperature.

Study of reactions for the production of uranium titrafluoride and uranium hexafluoride

International Nuclear Information System (INIS)

Guzella, M.F.R.

1985-01-01

The main production processes of uranium hexafluoride in pilot plants and industrial facilities are described. The known reactions confirmed in laboratory experiments that lead to Uf 6 or other intermediate fluorides are discussed. For the purpose of determining a thermodinamically feasible reaction involving the sulfur hexafluoride as fluorinating agent, a mock-up facility was designed and constructed as a part of the R and D work planned at the CDTN (Nuclebras Center for Nuclear Technology Development). IN the uranium tatrafluoride synthesis employing U 3 O 8 and SF 6 several experimental parameters are studied. The reaction time, gasflow, temperature and stoechiometic relations among reagents are described in detail. (Author) [pt

Summary of the engineering analysis report for the long-term management of depleted uranium hexafluoride

International Nuclear Information System (INIS)

Dubrin, J.W.; Rahm-Crites, L.

1997-09-01

The Department of Energy (DOE) is reviewing ideas for the long-term management and use of its depleted uranium hexafluoride. DOE owns about 560,000 metric tons (over a billion pounds) of depleted uranium hexafluoride. This material is contained in steel cylinders located in storage yards near Paducah, Kentucky; Portsmouth, Ohio; and at the East Tennessee Technology Park (formerly the K-25 Site) in Oak Ridge, Tennessee. On November 10, 1994, DOE announced its new Depleted Uranium Hexafluoride Management Program by issuing a Request for Recommendations and an Advance Notice of Intent in the Federal Register (59 FR 56324 and 56325). The first part of this program consists of engineering, costs and environmental impact studies. Part one will conclude with the selection of a long-term management plan or strategy. Part two will carry out the selected strategy

Summary of the engineering analysis report for the long-term management of depleted uranium hexafluoride

Energy Technology Data Exchange (ETDEWEB)

Dubrin, J.W., Rahm-Crites, L.

1997-09-01

The Department of Energy (DOE) is reviewing ideas for the long-term management and use of its depleted uranium hexafluoride. DOE owns about 560,000 metric tons (over a billion pounds) of depleted uranium hexafluoride. This material is contained in steel cylinders located in storage yards near Paducah, Kentucky; Portsmouth, Ohio; and at the East Tennessee Technology Park (formerly the K-25 Site) in Oak Ridge, Tennessee. On November 10, 1994, DOE announced its new Depleted Uranium Hexafluoride Management Program by issuing a Request for Recommendations and an Advance Notice of Intent in the Federal Register (59 FR 56324 and 56325). The first part of this program consists of engineering, costs and environmental impact studies. Part one will conclude with the selection of a long-term management plan or strategy. Part two will carry out the selected strategy.

Study of reactions for the obtention of uranium tetrafluoride and hexafluoride

International Nuclear Information System (INIS)

Guzella, M.F.R.

1984-01-01

Based on an exhaustive bibliographical review, the main production processes of uranium hexafluoride in pilot plants and industrial facilities are described. The known reactions, confirmed in laboratory experiments, that lead to UF 6 or other intermediate fluorides, are presented and discussed. In order to determine a new thermodinamically feasible reaction involving the sulfur hexafluoride as fluorinating agent, a mock-up facility was designed and constructed as part of the R and D work planned at CDTN (NUCLEBRAS Center for Nuclear Technology Development, MG - Brazil). For the UF 4 synthesis employing U 3 O 8 and SF 6 , several experimental parameters were studied. The reaction time, gas flow, temperature and stoichiometric relations among reagents are described in detail. Suggestions for further investigations regarding this new reagent are made. (Author) [pt

Research of heat releasing element of an active zone of gaseous nuclear reactor with pumped through nuclear fuel - uranium hexafluoride (UF6)

International Nuclear Information System (INIS)

Batyrbekov, G.; Batyrbekov, E.; Belyakova, E.; Kunakov, S.; Koltyshev, S.

1996-01-01

The purpose of the offered project is learning physics and substantiation of possibility of creation gaseous nuclear reactor with pumped through nuclear fuel-hexafluoride of uranium (Uf6).Main problems of this work are'. Determination of physic-chemical, spectral and optical properties of non-equilibrium nuclear - excited plasma of hexafluoride of uranium and its mixtures with other gases. Research of gas dynamics of laminar, non-mixing two-layer current of gases of hexafluoride of uranium and helium at availability and absence of internal energy release in hexafluoride of uranium with the purpose to determinate a possibility of isolation of hexafluoride of uranium from walls by inert helium. Creation and research of gaseous heat releasing element with pumped through fuel Uf6 in an active zone of research nuclear WWR-K reactor. Objects of a research: Non-equilibrium nuclear - excited plasma of hexafluoride of uranium and its mixtures with other gases. With use of specially created ampoules will come true in-reactor probe and spectral diagnostics of plasma. Calculations of kinetics with the account of main elementary processes proceeding in it, will be carried out. Two-layer non-mixed streams of hexafluoride of uranium and helium at availability and absence of internal energy release. Conditions of obtaining and characteristics of such streams will be investigated. Gaseous heat releasing element with pumped through fuel - Uf6 in an active zone of nuclear WWR-K reactor

Corrosion of Al-7075 by uranium hexafluoride

International Nuclear Information System (INIS)

1989-01-01

The results of the Al-7075 corrosion by uranium hexafluoride are presented in this work. The kinetic study shows that corrosion process occurs by two temperature dependent mechanism and that the alloy can be safely used up to 140 0 C. The corrosion film is formed by uranium oxifluoride with variable composition in depth. Two alternative corrosion models are proposed in order to explain the experimental results, as well as the tests taht will be carried out to confirm one of them [pt

Depleted uranium hexafluoride management program : data compilation for the Paducah site

International Nuclear Information System (INIS)

Hartmann, H.

2001-01-01

This report is a compilation of data and analyses for the Paducah site, near Paducah, Kentucky. The data were collected and the analyses were done in support of the U.S. Department of Energy (DOE) 1999 Programmatic Environmental Impact Statement for Alternative Strategies for the Long-Term Management and Use of Depleted Uranium Hexafluoride (DOE/EIS-0269). The report describes the affected environment at the Paducah site and summarizes potential environmental impacts that could result from conducting the following depleted uranium hexafluoride (UF 6 ) activities at the site: continued cylinder storage, preparation of cylinders for shipment, conversion, and long-term storage. DOE's preferred alternative is to begin converting the depleted UF 6 inventory as soon as possible to either uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible

Depleted uranium hexafluoride management program : data compilation for the Portsmouth site

International Nuclear Information System (INIS)

Hartmann, H. M.

2001-01-01

This report is a compilation of data and analyses for the Portsmouth site, near Portsmouth, Ohio. The data were collected and the analyses were done in support of the U.S. Department of Energy (DOE) 1999 Programmatic Environmental Impact Statement for Alternative Strategies for the Long-Term Management and Use of Depleted Uranium Hexafluoride (DOE/EIS-0269). The report describes the affected environment at the Portsmouth site and summarizes potential environmental impacts that could result from conducting the following depleted uranium hexafluoride (UF 6 ) management activities at the site: continued cylinder storage, preparation of cylinders for shipment, conversion, and long-term storage. DOE's preferred alternative is to begin converting the depleted UF 6 inventory as soon as possible to either uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible

Depleted uranium hexafluoride: Waste or resource?

International Nuclear Information System (INIS)

Schwertz, N.; Zoller, J.; Rosen, R.; Patton, S.; Bradley, C.; Murray, A.

1995-07-01

The US Department of Energy is evaluating technologies for the storage, disposal, or re-use of depleted uranium hexafluoride (UF 6 ). This paper discusses the following options, and provides a technology assessment for each one: (1) conversion to UO 2 for use as mixed oxide duel, (2) conversion to UO 2 to make DUCRETE for a multi-purpose storage container, (3) conversion to depleted uranium metal for use as shielding, (4) conversion to uranium carbide for use as high-temperature gas-cooled reactor (HTGR) fuel. In addition, conversion to U 3 O 8 as an option for long-term storage is discussed

Purification and preparation of bismuth(III) iodide for application as radiation semiconductor detector; Purificacao e preparacao do cristal semicondutor de iodeto de bismuto para aplicacao como detector de radiacao

Energy Technology Data Exchange (ETDEWEB)

Ferraz, Caue de Mello

2016-11-01

This study describes the experimental procedure of a BiI{sub 3} purification method powder, aiming a future application of these semiconductor crystals as room temperature radiation detector. The Repeated Vertical Bridgman Technique was applied for the purification, based on the melting and nucleation phenomena. An ampoule filled with a maximum of 25% by volume of BiI{sub 3} powder was mounted into the Bridgman furnace and vertically moved at a speed of 2 millimeters per hour, inside the furnace with programmed thermal gradient and temperature profile, at a temperature maximum of 530 deg C. The reduction of the impurities in the BiI{sub 3}, each purification, was analysed by Instrumental Neutron Activation Analysis (INAA), in order to evaluate the efficiency of the purification technique established in this work, for trace metal impurities. It was demonstrated that the Repeated Bridgman is effective to reduce the concentration of many impurities in BiI{sub 3}, such as Ag, As, Br, Cr, K, Mo, Na and Sb. The crystalline structure of the BiI{sub 3} crystal purified twice and third times was similar to the BiI{sub 3} pattern. However, for BiI{sub 3} powder and purified once an intensity contribution of the BiOI was observed in the diffractograms. It is known that semiconductor detectors fabricated from high purity crystal exhibit significant improvement in their performance compared to those produced from low purity crystals. (author)

Depleted uranium hexafluoride: Waste or resource?

Energy Technology Data Exchange (ETDEWEB)

Schwertz, N.; Zoller, J.; Rosen, R.; Patton, S. [Lawrence Livermore National Lab., CA (United States); Bradley, C. [USDOE Office of Nuclear Energy, Science, Technology, Washington, DC (United States); Murray, A. [SAIC (United States)

1995-07-01

the US Department of Energy is evaluating technologies for the storage, disposal, or re-use of depleted uranium hexafluoride (UF{sub 6}). This paper discusses the following options, and provides a technology assessment for each one: (1) conversion to UO{sub 2} for use as mixed oxide duel, (2) conversion to UO{sub 2} to make DUCRETE for a multi-purpose storage container, (3) conversion to depleted uranium metal for use as shielding, (4) conversion to uranium carbide for use as high-temperature gas-cooled reactor (HTGR) fuel. In addition, conversion to U{sub 3}O{sub 8} as an option for long-term storage is discussed.

Estimation of risks associated to land transport of uranium hexafluoride

International Nuclear Information System (INIS)

Pages, P.; Tomachevsky, E.

1987-01-01

The system analysed concerns the packaging 48Y containing about 12 tons of hexafluoride, 1000 tons/year are forecasted for 1990 on the 900 km road Pierrelatte-Le Havre (France). Probabilities are given by the accident file, container failure by impact or fire and sanitary consequences are analysed. Risk is evaluated and discussed [fr

Criticality concerns in cleaning large uranium hexafluoride cylinders

International Nuclear Information System (INIS)

Sheaffer, M.K.; Keeton, S.C.; Lutz, H.F.

1995-06-01

Cleaning large cylinders used to transport low-enriched uranium hexafluoride (UF 6 ) presents several challenges to nuclear criticality safety. This paper presents a brief overview of the cleaning process, the criticality controls typically employed and their bases. Potential shortfalls in implementing these controls are highlighted, and a simple example to illustrate the difficulties in complying with the Double Contingency Principle is discussed. Finally, a summary of recommended criticality controls for large cylinder cleaning operations is presented

Recovering of thorium contained in wastes from Thorium Purification Plant; Reaproveitamento do torio contido em residuos provenientes da Usina de Purificacao do Torio

Energy Technology Data Exchange (ETDEWEB)

Brandao Filho, D; Hespanhol, E C.B.; Baba, S; Miranda, L E.T.; Araujo, J.A. de

1992-08-01

A study has been developed in order to establish a chemical process for recovering thorium from wastes produced at the Thorium Purification Plant of the Instituto de Pesquisas Energeticas e Nucleares. The recovery of thorium in this process will be made by means of solvent extraction technique. Solutions of TBP/Varsol were employed as extracting agent during the runs. The influence of thorium concentration in the solution, aqueous phase acidity, volume ratio of the phases, percentage of TBP/Varsol and the contact time of the phases on the extraction of thorium and lanthanides was determined. (author).

Liver metastases: Sulphur hexafluoride-enhanced ultrasonography for lesion detection: a systematic review

NARCIS (Netherlands)

Cabassa, Paolo; Bipat, Shandra; Longaretti, Laura; Morone, Mario; Maroldi, Roberto

2010-01-01

This is a systematic review to evaluate the accuracy of contrast-enhanced ultrasonography (CEUS) performed with "SonoVue" (sulphur hexafluoride) in the detection of hepatic metastases. The MEDLINE, EMBASE and COCHRANE Databases were searched, regardless of language, for relevant articles published

Kinetics of low pressure chemical vapor deposition of tungsten silicide from dichlorocilane reduction of tungsten hexafluoride

International Nuclear Information System (INIS)

Srinivas, D.; Raupp, G.B.; Hillman, J.

1990-01-01

The authors report on experiments to determine the intrinsic surface reaction rate dependences and film properties' dependence on local reactant partial pressures and wafer temperature in low pressure chemical vapor deposition (LPCVD) of tungsten silicide from dichlorosilane reduction of tungsten hexafluoride. Films were deposited in a commercial-scale Spectrum CVD cold wall single wafer reactor under near differential, gradientless conditions. Over the range of process conditions investigated, deposition rate was found to be first order in dichlorosillane and negative second order in tungsten hexafluoride partial pressure. The apparent activation energy in the surface reaction limited regime was found to be 70-120 kcal/mol. The silicon to tungsten ratio of as deposited silicide films ranged from 1.1 to 2.4, and increased with increasing temperature and dichlorosillane partial pressure, and decreased with increasing tungsten hexafluoride pressure. These results suggest that the apparent silicide deposition rate and composition are controlled by the relative rates of at least two competing reactions which deposit stoichiometric tungsten silicides and/or silicon

{sup 123}I and {sup 13I} purification for biomolecules labelling; Purificacao de {sup 123}I e {sup 131}I para marcacao de biomoleculas

Energy Technology Data Exchange (ETDEWEB)

Catanoso, Marcela Forli

2011-07-01

The {sup 123}I and {sup 131}I are iodine radioisotopes widely used in Nuclear Medicine. The radioisotope {sup 123}I is used in diagnosis through the SPECT technique and is routinely produced at IPEN in cyclotron through the reaction: '1{sup 24}Xe (p, 2n) '1{sup 23}Cs -> {sup 123}Xe -> {sup 123}I. The radioisotope {sup 131}I is used both in diagnosis and therapy due to its physical characteristics of decay by {beta}{sup -} and its {gamma}-ray emissions that are softened with the use of specific collimators for diagnosis. It is routinely produced at IPEN using the nuclear reactor through the indirect reaction: {sup 130}Te (n, {gamma}) ->{sup 131}Te -> {sup 131}I, irradiating compounds containing Te. The radiopharmaceuticals prepared with these radioisotopes go through rigorous quality control tests and the chemical purity of the primary radioisotopes {sup 123}I and {sup 131}I are within the permissible limits currently defined. However, the presence of some chemical contaminants can prejudice the biomolecules labeling (monoclonal antibodies and peptides), that will produce radiopharmaceuticals of first generation to the oncology area. The aim of this work was to obtain a new purification method of these radioisotopes, allowing the labeling of biomolecules and also to established a process control on those radioisotopes. The methodology was separated on 3 steps: Evaluation of '1{sup 23}I e {sup 131}I radionuclidic purity using a hyper pure germanium detector, chemical purity using ICP-OES and the retention and elution study of {sup 131}I in several absorbers to choose the most appropriate for the purification tests analyzing the behavior of the possible contaminants. The radionuclidic analyses showed the presence of Te and Co on {sup 131}I samples and Te, Tc e Co on {sup 123}I samples. The chemical purity analyses showed the presence of Al and Mo in {sup 123}I, coming from the window material of the target holder and the presence of Al and Te in {sup

Study of the molecular structure of uranium hexafluoride

International Nuclear Information System (INIS)

Bougon, R.

1967-06-01

The vibrational spectrum of uranium hexafluoride has been studied in both the gaseous and solid states. The study of gaseous UF 6 confirms the regular octahedral structure of the fluorine atoms around the central U atom and makes it possible to evaluate some of the vibrational frequencies. From these, some new force constants have been determined. A tetragonal distortion is observed on solid UF 6 ; this distortion has only observed up till now by means of X-ray diffraction and nuclear magnetic resonance techniques. (author) [fr

Uranium hexafluoride liquid thermal expansion, elusive eutectic with hydrogen fluoride, and very first production using chlorine trifluoride

Energy Technology Data Exchange (ETDEWEB)

Rutledge, G.P. [Central Environmental, Inc., Anchorage, AK (United States)

1991-12-31

Three unusual incidents and case histories involving uranium hexafluoride in the enrichment facilities of the USA in the late 1940`s and early 1950`s are presented. The history of the measurements of the thermal expansion of liquids containing fluorine atoms within the molecule is reviewed with special emphasis upon uranium hexafluoride. A comparison is made between fluorinated esters, fluorocarbons, and uranium hexafluoride. The quantitative relationship between the thermal expansion coefficient, a, of liquids and the critical temperature, T{sub c} is presented. Uranium hexafluoride has an a that is very high in a temperature range that is used by laboratory and production workers - much higher than any other liquid measured. This physical property of UF{sub 6} has resulted in accidents involving filling the UF{sub 6} containers too full and then heating with a resulting rupture of the container. Such an incident at a uranium gaseous diffusion plant is presented. Production workers seldom {open_quotes}see{close_quotes} uranium hexafluoride. The movement of UF{sub 6} from one container to another is usually trailed by weight, not sight. Even laboratory scientists seldom {open_quotes}see{close_quotes} solid or liquid UF{sub 6} and this can be a problem at times. This inability to {open_quotes}see{close_quotes} the UF{sub 6}-HF mixtures in the 61.2{degrees}C to 101{degrees}C temperature range caused a delay in the understanding of the phase diagram of UF{sub 6}-HF which has a liquid - liquid immiscible region that made the eutectic composition somewhat elusive. Transparent fluorothene tubes solved the problem both for the UF{sub 6}-HF phase diagram as well as the UF{sub 6}-HF-CIF{sub 3} phase diagram with a miscibility gap starting at 53{degrees}C. The historical background leading to the first use of CIF{sub 3} to produce UF{sub 6} in both the laboratory and plant at K-25 is presented.

Hazard analysis in uranium hexafluoride production facility

International Nuclear Information System (INIS)

Marin, Maristhela Passoni de Araujo

1999-01-01

The present work provides a method for preliminary hazard analysis of nuclear fuel cycle facilities. The proposed method identify both chemical and radiological hazards, as well as the consequences associated with accident scenarios. To illustrate the application of the method, a uranium hexafluoride production facility was selected. The main hazards are identified and the potential consequences are quantified. It was found that, although the facility handles radioactive material, the main hazards as associated with releases of toxic chemical substances such as hydrogen fluoride, anhydrous ammonia and nitric acid. It was shown that a contention bung can effectively reduce the consequences of atmospheric release of toxic materials. (author)

Similarity of dependences of thermal conductivity and density of uranium and tungsten hexafluorides on desublimation conditions

International Nuclear Information System (INIS)

Barkov, V.A.

1989-01-01

Consideration is given to results of investigations of the dependence of thermal conductivity and density of UF 6 and WF 6 desublimates on volume content of hexafluoride in initial gaseous mixture. Similarity of these dependences, as well as the dependences of thermal conductivity of desublimates on their density was revealed. Generalized expressions, relating thermal conductivity and density of desublimates among each ofter and with volume content of hexafluoride in gaseous mixture were derived. Possibility of applying the generalized relations for calculation of thermal conductivity and density of other compounds of MeF 6 type under prescribed desublimation conclitions is shown. 15 refs.; 6 figs

Chemistry of the 5g Elements: Relativistic Calculations on Hexafluorides.

Science.gov (United States)

Dognon, Jean-Pierre; Pyykkö, Pekka

2017-08-14

A Periodic System was proposed for the elements 1-172 by Pyykkö on the basis of atomic and ionic calculations. In it, the elements 121-138 were nominally assigned to a 5g row. We now perform molecular, relativistic four-component DFT calculations and find that the hexafluorides of the elements 125-129 indeed enjoy occupied 5g states. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chemistry of the 5g elements. Relativistic calculations on hexafluorides

International Nuclear Information System (INIS)

Dognon, Jean-Pierre; Pyykkoe, Pekka

2017-01-01

A Periodic System was proposed for the elements 1-172 by Pyykkoe on the basis of atomic and ionic calculations. In it, the elements 121-138 were nominally assigned to a 5g row. We now perform molecular, relativistic four-component DFT calculations and find that the hexafluorides of the elements 125-129 indeed enjoy occupied 5g states. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Chemistry of the 5g elements. Relativistic calculations on hexafluorides

Energy Technology Data Exchange (ETDEWEB)

Dognon, Jean-Pierre [NIMBE, CEA, CNRS, Universite Paris-Saclay, CEA Saclay, Gif-sur-Yvette (France); Pyykkoe, Pekka [Department of Chemistry, University of Helsinki (Finland)

2017-08-14

A Periodic System was proposed for the elements 1-172 by Pyykkoe on the basis of atomic and ionic calculations. In it, the elements 121-138 were nominally assigned to a 5g row. We now perform molecular, relativistic four-component DFT calculations and find that the hexafluorides of the elements 125-129 indeed enjoy occupied 5g states. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Standard model for safety analysis report of hexafluoride power plants from natural uranium

International Nuclear Information System (INIS)

1983-01-01

The standard model for safety analysis report for hexafluoride production power plants from natural uranium is presented, showing the presentation form, the nature and the degree of detail, of the minimal information required by the Brazilian Nuclear Energy Commission - CNEN. (E.G.) [pt

Kinetics of gaseous uranium hexafluoride reaction with hydrogen chloride

International Nuclear Information System (INIS)

Ezubchenko, A.N.; Ilyukhin, A.I.; Merzlyakov, A.V.

1993-01-01

Kinetics of decrease of concentration of gaseous uranium hexafluoride in reaction with hydrogen chloride at temperatures close to room ones, was investigated by the method of IR spectroscopy. It was established that the process represented the first order reaction by both UF 6 and HCl. Activation energy of the reaction was determined: 7.6 ± 0.7 kcal/mol. Specific feature of reaction kinetics was noted: inversely proportional dependence of effective constant on UF 6 initial pressure. 5 refs., 3 figs

The handling of plutonium hexafluoride (1962); Manipulation de l'hexafluorure de plutonium (1962)

Energy Technology Data Exchange (ETDEWEB)

Berard, Ph [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1961-11-15

The major problem posed in this work is the instability of plutonium hexafluoride. The influence of various factors on the decomposition of the fluoride has been studied: physical aspect of the walls, nature of the metal and its pretreatment, influence of the temperature. A means of detecting plutonium-239 in a metallic apparatus by {gamma}-ray counting has been developed; the sensitivity is of the order of half a milligram, but the precision is very low (about 50 per cent). Yields of over 95 per cent have been obtained for the transfer of plutonium during the preparation and sublimation of the hexafluoride. This study confirms the possibility of using plutonium hexafluoride for the extraction of plutonium from irradiated fuel elements by a dry method. (author) [French] Le probleme majeur de cette etude a ete l'instabilite de l'hexafluorure de plutonium. Nous avons etudie l'influence de divers facteurs sur la decomposition de l'hexafluorure: aspect physique des parois, nature du metal et de son pretraitement, influence de la temperature. Nous avons mis au point un mode de detection du plutonium-239 dans un appareillage metallique par comptage du rayonnement {gamma}; la sensibilite est de l'ordre du demi-milligramme, mais la precision est tres faible (50 pour cent environ). Nous avons obtenu des rendements depassant 95 pour cent dans le transfert du plutonium au cours de la fabrication et de la sublimation de l'hexafluorure. Cette etude confirme la possibilite d'utiliser l'hexafluorure de plutonium dans l'extraction du plutonium des combustibles irradies par voie seche. (auteur)

Investigation of transformation of uranium hexafluoride into dioxide

International Nuclear Information System (INIS)

Galkin, N.P.; Veryatin, U.D.; Yakhonin, I.F.; Logunov, A.F.; Dymkov, Yu.M.

1982-01-01

The process of transformation of uranium hexafluoride into dioxide using the method of pyrohydrolysis by steam-hydrogen mixture in a boiling layer using uranium dioxide granules applicable for production of fuel elements is considered. Technological parameters and equipment of the process are described, intermediate stages and process products are considered. Physicochemical and physicomechanical properties of the obtained uranium dioxide granules are given. The results of metallographical investigations into solid products of pyrohydrolysis in phase transformations at certain stages of the process as well as test on vibration packing of the obtained granules in fuel cans are presented

Cost update technology, safety, and costs of decommissioning a reference uranium hexafluoride conversion plant

International Nuclear Information System (INIS)

Miles, T.L.; Liu, Y.

1995-08-01

The purpose of this study is to update the cost estimates developed in a previous report, NUREG/CR-1757 (Elder 1980) for decommissioning a reference uranium hexafluoride conversion plant from the original mid-1981 dollars to values representative of January 1993. The cost updates were performed by using escalation factors derived from cost index trends over the past 11.5 years. Contemporary price quotes wee used for costs that have increased drastically or for which is is difficult to find a cost trend. No changes were made in the decommissioning procedures or cost element requirements assumed in NUREG/CR-1757. This report includes only information that was changed from NUREG/CR-1757. Thus, for those interested in detailed descriptions and associated information for the reference uranium hexafluoride conversion plant, a copy of NUREG/CR-1757 will be needed

Chemical toxicity of uranium hexafluoride compared to acute effects of radiation

International Nuclear Information System (INIS)

McGuire, S.A.

1991-02-01

The chemical effects from acute exposures to uranium hexafluoride are compared to the nonstochastic effects from acute radiation doses of 25 rems to the whole body and 300 rems to the thyroid. The analysis concludes that an intake of about 10 mg of uranium in soluble form is roughly comparable, in terms of early effects, to an acute whole body dose of 25 rems because both are just below the threshold for significant nonstochastic effects. Similarly, an exposure to hydrogen fluoride at a concentration of 25 mg/m 3 for 30 minutes is roughly comparable because there would be no significant nonstochastic effects. For times t other than 30 minutes, the concentration C of hydrogen fluoride considered to have the same effect can be calculated using a quadratic equation: C = 25 mg/m 3 (30 min/t). The purpose of these analyses is to provide information for developing design and siting guideline based on chemical toxicity for enrichment plants using uranium hexafluoride. These guidelines are to be similar, in terms of stochastic health effects, to criteria in NRC regulations of nuclear power plants, which are based on radiation doses. 26 refs., 1 fig., 5 tabs

Chemical toxicity of uranium hexafluoride compared to acute effects of radiation

Energy Technology Data Exchange (ETDEWEB)

McGuire, S.A.

1991-02-01

The chemical effects from acute exposures to uranium hexafluoride are compared to the nonstochastic effects from acute radiation doses of 25 rems to the whole body and 300 rems to the thyroid. The analysis concludes that an intake of about 10 mg of uranium in soluble form is roughly comparable, in terms of early effects, to an acute whole body dose of 25 rems because both are just below the threshold for significant nonstochastic effects. Similarly, an exposure to hydrogen fluoride at a concentration of 25 mg/m{sup 3} for 30 minutes is roughly comparable because there would be no significant nonstochastic effects. For times t other than 30 minutes, the concentration C of hydrogen fluoride considered to have the same effect can be calculated using a quadratic equation: C = 25 mg/m{sup 3} (30 min/t). The purpose of these analyses is to provide information for developing design and siting guideline based on chemical toxicity for enrichment plants using uranium hexafluoride. These guidelines are to be similar, in terms of stochastic health effects, to criteria in NRC regulations of nuclear power plants, which are based on radiation doses. 26 refs., 1 fig., 5 tabs.

Evaluation of sulfur hexafluoride and helium for steam generator leak location: Final report

International Nuclear Information System (INIS)

Kassen, W.R.

1987-01-01

Since the use of sulfur hexafluoride as a tracer for identifying sources of primary to secondary leakage in PWR steam generators appeared to offer significant sensitivity advantages, the thermal stability of sulfur hexafluoride in water was evaluated at steam generator operating temperature. Significant decomposition was observed after 2 to 4 hours at temperature. Key decomposition products were fluoride and sulfide ions. Based on this observation and these limited test results, the use of SF 6 for PWR steam generator leak location can not be recommended at this time. A survey of 15 utilities was conducted in regard to their application experience with the helium tracer-mass spectroscopy technique for steam generator leak location. Although several successful steam generator integrity programs do not include use of this technique, it has proven to be a useful addition to the inspection program at some plants. No corrosion concerns appear to be associated with this technique

Depleted uranium hexafluoride management program : data compilation for the K-25 site

International Nuclear Information System (INIS)

Hartmann, H. M.

2001-01-01

This report is a compilation of data and analyses for the K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The data were collected and the analyses were done in support of the U.S. Department of Energy (DOE) 1999 Programmatic Environmental Impact Statement for Alternative Strategies for the Long-Term Management and Use of Depleted Uranium Hexafluoride (DOE/EIS-0269). The report describes the affected environment at the K-25 site and summarizes the potential environmental impacts that could result from continued cylinder storage and preparation of cylinders for shipment at the site. It is probable that the cylinders at the K-25 site will be shipped to another site for conversion. Because conversion and long-term storage of the entire inventory at the K-25 site are highly unlikely, these data are not presented in this report. DOE's preferred alternative is to begin converting the depleted uranium hexafluoride inventory as soon as possible to either uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible

Spectroscopy of hexafluorides with an odd number of electrons; Spectroscopie des hexafluorures a nombre impair d'electrons

Energy Technology Data Exchange (ETDEWEB)

Boudon, V

1995-05-01

From a theoretical point of view, a tensorial formalism adapted to the study of molecules or octahedral ions with a half-integer angular momentum has been developed for the first time. We have used here the method of projective representations, more consistent than that of double groups. A complete set of coupling coefficients and formulas, as well as the corresponding computing programs have been elaborated. This has firstly allowed us to write a simple model describing the vibronic structure of colored hexafluorides. Then, some applications of this formalism to the study of ro-vibronic couplings of XY{sub 6} molecules in a fourfold degenerate electronic state have been considered, especially concerning operators associated to dynamic Jahn-Teller effect. From an experimental point of view, we have considered IrF{sub 6}, for which we have mastered the synthesis, purification and conservation processes. A first study at low resolution (absorption and Raman scattering) has been performed for this molecule. We have then set up two high resolution spectroscopic devices in the visible region (saturated absorption - tested with an iodine cell- and simple absorption with multiple pass). These especially use a dye laser. They should now allow the spectroscopy of the visible band of IrF{sub 6} in order to resolve for the first time its fine rotational structure. (author)

Emission characteristics of uranium hexafluoride at high temperatures

International Nuclear Information System (INIS)

Krascella, N.L.

1976-01-01

An experimental study was conducted to ascertain the spectral characteristics of uranium hexafluoride (UF 6 ) and possible UF 6 thermal decomposition products as a function of temperature and pressure. Relative emission measurements were made for UF 6 /Argon mixtures heated in a plasma torch over a range of temperatures from 800 to about 3600 0 K over a wavelength range from 80 to 600 nm. Total pressures were varied from 1 to approximately 1.7 atm. Similarly absorption measurements were carried out in the visible region from 420 to 580 nm over a temperature range from about 1000 to 1800 0 K. Total pressure for these measurements was 1.0 atm

Standard test method for the analysis of refrigerant 114, plus other carbon-containing and fluorine-containing compounds in uranium hexafluoride via fourier-transform infrared (FTIR) spectroscopy

CERN Document Server

American Society for Testing and Materials. Philadelphia

2004-01-01

1.1 This test method covers determining the concentrations of refrigerant-114, other carbon-containing and fluorine-containing compounds, hydrocarbons, and partially or completely substituted halohydrocarbons that may be impurities in uranium hexafluoride. The two options are outlined for this test method. They are designated as Part A and Part B. 1.1.1 To provide instructions for performing Fourier-Transform Infrared (FTIR) spectroscopic analysis for the possible presence of Refrigerant-114 impurity in a gaseous sample of uranium hexafluoride, collected in a "2S" container or equivalent at room temperature. The all gas procedure applies to the analysis of possible Refrigerant-114 impurity in uranium hexafluoride, and to the gas manifold system used for FTIR applications. The pressure and temperatures must be controlled to maintain a gaseous sample. The concentration units are in mole percent. This is Part A. 1.2 Part B involves a high pressure liquid sample of uranium hexafluoride. This method can be appli...

Selection of a management strategy for depleted uranium hexafluoride

International Nuclear Information System (INIS)

Patton, S.E.; Hanrahan, E.J.; Bradley, C.E.

1995-01-01

A consequence of the uranium enrichment process used in the United States (US) is the accumulation of a significant amount of depleted uranium hexafluoride (UF 6 ). Currently, approximately 560,000 metric tons of the material are stored at three different sites. The US Department of Energy (DOE) has recently initiated a program to consider alternative strategies for the cost-effective and environmentally safe long-term management of this inventory of depleted UF 6 . The program involves a technology and engineering assessment of proposed management options (use/reuse, conversion, storage, or disposal) and an analysis of the potential environmental impacts and life-cycle costs of alternative management strategies. The information obtained from the studies will be used by the DOE to select a preferred long-term management strategy. The selection and implementation of a management strategy will involve consideration of a number of important issues such as environmental, health, and safety effects; the balancing of risks versus costs in a context of reduced government spending; socioeconomic implications, including effects on the domestic and international uranium industry; the technical status of proposed uses or technologies; and public involvement in the decision making process. Because of its provisions for considering a wide range of relevant issues and involving the public, this program has become a model for future DOE materials disposition programs. This paper presents an overview of the Depleted Uranium Hexafluoride Management Program. Technical findings of the program to date are presented, and major issues involved in selecting and implementing a management strategy are discussed

Obtention of uranium tetrafluoride from effluents generated in the hexafluoride conversion process

International Nuclear Information System (INIS)

Silva Neto, J.B.; Urano de Carvalho, E.F.; Durazzo, M.; Riella, H.G.

2009-01-01

Full text: The uranium silicide (U3Si2) fuel is produced from uranium hexafluoride (UF6) as the primary raw material. The uranium tetrafluoride (UF4) and metallic uranium are the two subsequent steps. There are two conventional routes for UF4 production: the first one reduces the uranium from the UF6 hydrolysis solution by adding stannous chloride (SnCl2). The second one is based on the hydrofluorination of solid uranium dioxide (UO2) produced from the ammonium uranyl carbonate (AUC). This work introduces a third route, a dry way route which utilizes the recovering of uranium from liquid effluents generated in the uranium hexafluoride reconversion process adopted at IPEN/CNEN-SP. Working in the liquid phase, this route comprises the recovery of ammonium fluoride by NH4HF2 precipitation. The crystallized bifluoride is added to the solid UO2 to get UF4, which returns to the metallic uranium production process and, finally, to the U3Si2 powder production. The UF4 produced by this new route was chemically and physically characterized and will be able to be used as raw material for metallic uranium production by magnesiothermic reduction. (author)

Previsional evaluation of risks associated with ground transportation of uranium hexafluoride

International Nuclear Information System (INIS)

Pages, P.; Tomachevsky, E.

1987-11-01

This communication is a concrete example of application of the evaluation method for risks associated with road transportation of uranium hexafluoride by 48Y shipping container. The statistical bases for UF6 transportation are given by analysis of the list of accidents for dangerous road transportation. This study examines all parameters (cost-safety-meteorology-radiation doses) to take in account in the safety analysis of the UF6 transportation between Pierrelatte and Le Havre [fr

Spectroscopy of hexafluorides with an odd number of electrons; Spectroscopie des hexafluorures a nombre impair d'electrons

Energy Technology Data Exchange (ETDEWEB)

Boudon, V

1995-05-01

From a theoretical point of view, a tensorial formalism adapted to the study of molecules or octahedral ions with a half-integer angular momentum has been developed for the first time. We have used here the method of projective representations, more consistent than that of double groups. A complete set of coupling coefficients and formulas, as well as the corresponding computing programs have been elaborated. This has firstly allowed us to write a simple model describing the vibronic structure of colored hexafluorides. Then, some applications of this formalism to the study of ro-vibronic couplings of XY{sub 6} molecules in a fourfold degenerate electronic state have been considered, especially concerning operators associated to dynamic Jahn-Teller effect. From an experimental point of view, we have considered IrF{sub 6}, for which we have mastered the synthesis, purification and conservation processes. A first study at low resolution (absorption and Raman scattering) has been performed for this molecule. We have then set up two high resolution spectroscopic devices in the visible region (saturated absorption - tested with an iodine cell- and simple absorption with multiple pass). These especially use a dye laser. They should now allow the spectroscopy of the visible band of IrF{sub 6} in order to resolve for the first time its fine rotational structure. (author)

Hydrogen purification for fuel cell by copper promoted gold catalysts; Purificacao de hidrogenio para pilha a combustivel utilizando catalisadores de ouro promovidos com cobre

Energy Technology Data Exchange (ETDEWEB)

Mozer, Thiago S.; Vieira, Carlos T.P.; Passos, Fabio B. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil); Dziuba, Dominika A. [Hochschule Mannheim (Germany)

2008-07-01

Copper promoted gold catalysts were studied for hydrogen purification through selective CO oxidation. The Cu acted as a selectivity promoter favoring the CO conversion and decreasing the H{sub 2} consumption. The deposition-precipitation method, used to prepare the samples generated small and well dispersed gold particles, as the UV-vis DRS spectra did not show the 'plasmon' band, which indicates that the samples are active for SELOX. The activity tests showed high CO conversion, the bimetallic 2,5%Au-0,5%Cu/Al{sub 2}O{sub 3} catalyst showed the best behavior in the tested condition, 95% of CO conversion and 75% of selectivity at 50 deg C. Increasing the O{sub 2} content in the feedstream the CO conversion also increased, although the selectivity decreased. (author)

A review of laser isotope separation of uranium hexafluoride

International Nuclear Information System (INIS)

Kelly, J.W.

1983-04-01

There is continuing world-wide interest in the possibility of enriching uranium by a laser process which uses uranium hexafluoride. Since no actual commercial plant exists at present, this review examines the key areas of related research. It concludes that such a process is feasible, that it must employ an adiabatic cooling system, with UF 6 the minor constituent in a predominantly monatomic or diatomic carrier gas, that the necessary infrared and/or ultraviolet-visible lasers are in a state of development bordering on the minimum required, and that the economics of such a process appear highly promising

Dynamic tests for qualifying of national uranium hexafluoride

International Nuclear Information System (INIS)

Araujo Figueiredo, C. de; Abreu Mendonca Schvartzman, M.M. de; Vasconcelos, M.C.R.L.

1990-01-01

The dynamic behaviour of the Brazilian uranium hexafluoride is analyzed in this paper, with regard to its radiolytic decomposition and to the action of catalysts on the reaction between UF 6 and H 2 . The process gas (UF 6 /H 2 ) was submitted in the laboratory of dynamic tests (DV-II) to similar conditions as those used in the enrichment plant presently being erected in Resende - RJ, 'First Cascade - FC'. The tests carried out have shown that the Brazilian UF 6 has the same dynamic behaviour of the German UF 6 . It does not contain either any catalyst of the reaction between UF 6 and H 2 which could render it inappropriate for use in commercial plants. (author) [pt

Acute toxicity of uranium hexafluoride, uranyl fluoride and hydrogen fluoride

International Nuclear Information System (INIS)

Just, R.A.

1988-01-01

Uranium hexafluoride (UF 6 ) released into the atmosphere will react rapidly with moisture in the air to form the hydrolysis products uranyl fluoride (UO 2 F 2 ) and hydrogen fluoride (HF). Uranium compounds such as UF 6 and UO 2 F 2 exhibit both chemical toxicity and radiological effects, while HF exhibits only chemical toxicity. This paper describes the development of a methodology for assessing the human health consequences of a known acute exposure to a mixture of UF 6 , UO 2 F 2 , and HF. 4 refs., 2 figs., 5 tabs

Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of uranium hexafluoride

CERN Document Server

American Society for Testing and Materials. Philadelphia

2011-01-01

1.1 These test methods cover procedures for subsampling and for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of uranium hexafluoride UF6. Most of these test methods are in routine use to determine conformance to UF6 specifications in the Enrichment and Conversion Facilities. 1.2 The analytical procedures in this document appear in the following order: Note 1—Subcommittee C26.05 will confer with C26.02 concerning the renumbered section in Test Methods C761 to determine how concerns with renumbering these sections, as analytical methods are replaced with stand-alone analytical methods, are best addressed in subsequent publications. Sections Subsampling of Uranium Hexafluoride 7 - 10 Gravimetric Determination of Uranium 11 - 19 Titrimetric Determination of Uranium 20 Preparation of High-Purity U3O 8 21 Isotopic Analysis 22 Isotopic Analysis by Double-Standard Mass-Spectrometer Method 23 - 29 Determination of Hydrocarbons, Chlorocarbons, and Partially Substitut...

Uranium hexafluoride: Safe handling, processing, and transporting: Conference proceedings

Energy Technology Data Exchange (ETDEWEB)

Strunk, W.D.; Thornton, S.G. (eds.)

1988-01-01

This conference seeks to provide a forum for the exchange of information and ideas of the safety aspects and technical issue related to the handling of uranium hexafluoride. By allowing operators, engineers, scientists, managers, educators, and others to meet and share experiences of mutual concern, the conference is also intended to provide the participants with a more complete knowledge of technical and operational issues. The topics for the papers in the proceedings are widely varied and include the results of chemical, metallurgical, mechanical, thermal, and analytical investigations, as well as the developed philosophies of operational, managerial, and regulatory guidelines. Papers have been entered individually into EDB and ERA. (LTN)

Uranium hexafluoride: Safe handling, processing, and transporting: Conference proceedings

International Nuclear Information System (INIS)

Strunk, W.D.; Thornton, S.G.

1988-01-01

This conference seeks to provide a forum for the exchange of information and ideas of the safety aspects and technical issue related to the handling of uranium hexafluoride. By allowing operators, engineers, scientists, managers, educators, and others to meet and share experiences of mutual concern, the conference is also intended to provide the participants with a more complete knowledge of technical and operational issues. The topics for the papers in the proceedings are widely varied and include the results of chemical, metallurgical, mechanical, thermal, and analytical investigations, as well as the developed philosophies of operational, managerial, and regulatory guidelines. Papers have been entered individually into EDB and ERA

Some parameters of uranium hexafluoride plasma produced by products of nuclear reaction

International Nuclear Information System (INIS)

Batyrbekov, G.A.; Belyakova, Eh.A.

1996-01-01

The probe experimental results of investigation of uranium hexafluoride plasma produced in the centre of nuclear reactor core were demonstrated. Study of uranium hexafluoride plasma is continued by the following reasons: a possibility of U F 6 utilization as nuclear fuel, the utilization of U F 6 as volume source o ionization, search of active laser media compatible with U F 6 that is complicated by lack of constant rates data for most of plasma-chemical reactions with U F 6 and his dissociation products. Cylindrical probe volt-ampere characteristics (VAC) measured in U F 6 plasma at pressure 20 Torr and different thermal neutron fluxes and have following features: -firstly, it is possible to choose a linear part in the field of small positive potentials of probe (0-1) V; - secondary, ion branches of VAC have typical break which current of satiation corresponds to; -thirdly, probe VAC measured at small values of thermal neutron flux density are symmetrical. Diagnostics approaches were used for interpretation VAC of probe. The values of satiation current and linear part of electron branch were calculated, and such plasma parameters as conductivity, diffusion coefficient values of positive and negative ions were determined. The resonance recharge cross section was estimated on diffusion coefficient value

The uranium fuel cycle at IPEN - Energy and Nuclear Research Institute, SP, Brazil

International Nuclear Information System (INIS)

Abrao, Alcidio

1994-09-01

This paper summarizes the progress of research concerning the uranium fuel cycle set up at the IPEN, Sao Paulo, from the raw yellow-cake to the uranium hexafluoride. It covers the reconversion of the hexafluoride to ammonium uranyl tricarbonate and the manufacturing of the fuel elements for the swimming pool IEA-R1 reactor. This review extends the coverage of two pilot plants for uranium purification based upon ion exchange, one demonstration unity for the purification of uranyl nitrate by solvent extraction in pulsed columns, the unity of uranium tetrafluoride into moving bed reactors and a second one based upon the wet chemistry via uranium dioxide and aqueous hydrogen fluoride. The paper mentions the pilot plant for the preparation of uranium trioxide by the thermal decomposition of ammonium diuranate and a second unity by the thermal denitration of uranyl nitrate. The paper outlines the fluorine plant and the unity for the hexafluoride preparation, the unity for the conversion of the hexa to the ammonium uranyl tricarbonate and the fabrication of fuel elements for the IEA-R1 reactor. (author)

World War II uranium hexafluoride inhalation event with pulmonary implications for today

International Nuclear Information System (INIS)

Moore, R.H.; Kathren, R.L.

1985-01-01

Two individuals were exposed to massive quantities of airborne uranium hexafluoride (UF6) and its hydrolysis products following a World War II equipment rupture. An excretion pattern for uranium exhibited by these patients is, in light of current knowledge, anomalous. The possible role of pulmonary edema is discussed. Examination of these individuals 38 years later showed no physical changes believed to be related to their uranium exposure and no deposition of uranium could be detected

Development of methods for the purification of {sup 67}Ga and {sup 68}Ga for biomolecules labeling; Desenvolvimento de metodos de purificacao do {sup 67}Ga e {sup 68}Ga para a marcacao de biomoleculas

Energy Technology Data Exchange (ETDEWEB)

Costa, Renata Ferreira

2012-07-01

For more than fifty years, the long-lived {sup 68}Ge/{sup 68}Ga generators have been in development, obtaining {sup 68}Ga without the need of having in house cyclotron, which is a considerable convenience for PET centers that have no nearby cyclotrons. {sup 68}Ga decays 89% by positron emission and low photon emission (1077 keV) and the physical half life of 67.7 minutes is compatible with the pharmacokinetics of low biomolecular weight substances like peptides and antibody fragments. Moreover, its established metallic chemistry allows it to be stably bound to the carrier peptide sequence via a suitable bifunctional chelator, such as DOTA. All these reasons together with the technology of PET/CT allowed advances in molecular imaging, in particular in the diagnosis of neuroendocrine diseases. However, the eluate from the commercial {sup 68}Ge/{sup 68}Ga generators still contains high levels of long lived {sup 68}Ge, besides other metallic impurities, which competes with {sup 68}Ga with a consequent reduction of the labeling yield of biomolecules, such as Fe{sup 3+} and Zn{sup 2+}. Thus, the lower the amount of impurities in the eluate, the competition between the radiolabeled and unlabeled peptide by the receptor will be smaller and the quality of imaging will be better, a subsequent purification step is needed after the generator elution. The aim of this work is to evaluate different purifications methods of {sup 68}Ga to label biomolecules, with emphasis on the study of the chemical impurities contained in the eluate and to develop a new purification method. Several purification methods were studied. Many cationic resin were tested simulating the commercial process. {sup 68}Ga is adsorbed in cationic resin, which is not commercial available and eluted in acid/acetone solution. The use of minor particles of cationic resin AG50W-X4 (200-400 mesh) showed the best results. An innovate method was the extraction chromatography, which is based on the absorption of

Degradation and dielectric properties of sulfur hexafluoride

International Nuclear Information System (INIS)

Fluck, Eric

1985-01-01

Sparking potential of sulfur hexafluoride is studied as a function of its decomposition by electrical discharges. The analysis of the gas is performed by mass spectrometry. The quantity of products resulting from spark discharges as a function of charge transported is plotted for SO_2F_2, SiF_4, SOF_4; it shows a linear increase with charge transported. Production rates of fluoride gases strongly increase with quantity of water vapor present at the beginning of the spark discharges. Decomposition of the gas, even at high levels (20%) does not exhibit measurable variations of sparking potential (at constant pressure). Production of SiF_4 by degradation of glass walls by hydrofluoric acid produced by discharges shows the important role played by this acid in the decomposition of the gas. It is necessary to use a gas containing water impurities at a level as small as possible. (author)

Uranium hexafluoride: handling procedures and container criteria

International Nuclear Information System (INIS)

1977-04-01

The U.S. Energy Research and Development Administration's (ERDA) procedures for packaging, measuring, and transferring uranium hexafluoride (UF 6 ) have been undergoing continual review and revision for several years to keep them in phase with developing agreements for the supply of enriched uranium. This report, first issued in 1966, was reissued in 1967 to make editorial changes and to provide for minor revisions in procedural information. In 1968 and 1972, Revisions 2 and 3, respectively, were issued as part of the continuing effort to present updated information. This document, Revision 4, includes primarily revisions to UF 6 cylinders, valves, and methods of use. This revision supersedes all previous issues of this report. The procedures will normally apply in all transactions involving receipt or shipment of UF 6 by ERDA, unless stipulated otherwise by contracts or agreements with ERDA or by notices published in the Federal Register

Infrared analysis of hydrogen fluoride in uranium hexafluoride

International Nuclear Information System (INIS)

Ohwada, Ken; Soga, Takeshi; Iwasaki, Matae; Tsujimura, Shigeo

1975-01-01

Quantitative analysis by infrared technique was made on hydrogen fluoride (HF) contained in uranium hexafluoride (UF 6 ). It was found that, among the vibration-rotation bands, the R(1)-, R(2)-, P(2)- and P(3)-branches having relatively large absorbances are convenient for the analysis of HF. Upon comparing the calibration curves of pure HF with the HF absorbances observed in the presence of UF 6 (approx. 70--100 Torr), N 2 (approx. 100 Torr) and Ar(approx. 100 Torr) gases, it was observed that the first-mentioned calibration curve could be applied to the analysis of HF when mixed with other substances, as in the latter cases. The detectable limits of HF pressure, using a infrared cell of 10cm path length, were 0.5--1 Torr at room temperature. (auth.)

Status of overpacks for uranium hexafluoride transport

International Nuclear Information System (INIS)

Arendt, J.W.; Pryor, W.A.

1985-01-01

The original overpacks for uranium hexafluoride (UF 6 ) transport, which utilized phenolic foam insulation, were developed in the 1960's and ultimately became international standards. A second generation of overpacks for 10-ton-capacity UF 6 cylinders used polyurethane foam and was developed in the early 1970's. In the mid 1970's, a third generation was designed, but no attempt to develop it occurred until the early 1980's, when full-scale testing of an overpack for 14-ton capacity UF 6 cylinders was initiated and resulted in designs for a new family of UF 6 overpacks. In the meantime, two additional developments affected overpack use for UF 6 cylinder transport: (1) the discovery that phenolic-foam-insulated overpacks have water absorption and outleakage problems inaugurated a program for their improvement and (2) new polyurethane-insulated overpacks were manufactured. The current status of all these overpacks, including their designs, testing, and approval for transport is presented

Study of neptunium hexafluoride formation and its adsorption on metallic fluorides

International Nuclear Information System (INIS)

Matcheret, Georges

1970-01-01

This report involves two parts. The first part deals with the action of elementary fluorine on neptunium compounds by a thermogravimetric method. The mechanism and the kinetics of this reaction vary according to the nature of the compound. 1 - With neptunium tetrafluoride the reaction, proceeds in a single step. The kinetics corresponds to a uniform attack of the entire surface of the sample and follows the kinetics law: (1-α) 1/3 1-k rel t . 2 - The reaction with neptunium dioxyde involves two steps, neptunium tetrafluoride being the intermediate compound. The kinetics of the first step corresponds to a diffusion process and follows the kinetic law: log (1-α) = kt 1/2 . The kinetics of the second step corresponds to an uniform attack of the entire sur face of the sample. The object of the second part is a study of the adsorption of uranium hexafluoride and neptunium hexafluoride on sodium, magnesium and barium fluorides by a volumetric method. The adsorption of UF 6 on MgF 2 has been investigated at 20 deg. C. The isothermal curve obtained is characteristic of a physical one layer monomolecular adsorption. In a way similar to the behaviour of UF 6 the adsorption of NpF 6 involves in addition a chemical reduction with formation of NpF 5 and release of fluorine. The reaction of NpF 6 with BaF 2 permitted to confirm the influence of the polarizing power of the Ba ++ ion on formation and stability of the product of addition. (author) [fr

Sulfur hexafluoride purification from mixtures with air: a process feasibility study for the Holifield Heavy Ion Research Facility

International Nuclear Information System (INIS)

Perona, J.J.

1979-01-01

A preliminary feasibility study was made for the purification of SF 6 vapor contaminated with air for application at the Holifield Heavy Ion Research Facility. Liquefaction appears to be a good way to recover about 90% of the SF 6 if it is badly contaminated (15% air), and even greater recovery will be possible for mixtures containing less air. Where liquefaction is insufficient alone, adsorption of SF 6 on activated carbon at -50 0 F looks promising. Two carbon beds each containing about 500 lb of carbon should be sufficient. The refrigeration system for liquefaction and adsorption would have a capacity of about 2 tons. As alternatives, the use of molecular sieves to trap out the air was investigated, but such a bed would require at least 15,000 lb of molecular sieves and very long cycle times. A large-scale desublimer was investigated and appears workable but would require some development work to permit design work to proceed with confidence

Depleted uranium hexafluoride: The source material for advanced shielding systems

Energy Technology Data Exchange (ETDEWEB)

Quapp, W.J.; Lessing, P.A. [Idaho National Engineering Lab., Idaho Falls, ID (United States); Cooley, C.R. [Department of Technology, Germantown, MD (United States)

1997-02-01

The U.S. Department of Energy (DOE) has a management challenge and financial liability problem in the form of 50,000 cylinders containing 555,000 metric tons of depleted uranium hexafluoride (UF{sub 6}) that are stored at the gaseous diffusion plants. DOE is evaluating several options for the disposition of this UF{sub 6}, including continued storage, disposal, and recycle into a product. Based on studies conducted to date, the most feasible recycle option for the depleted uranium is shielding in low-level waste, spent nuclear fuel, or vitrified high-level waste containers. Estimates for the cost of disposal, using existing technologies, range between $3.8 and $11.3 billion depending on factors such as the disposal site and the applicability of the Resource Conservation and Recovery Act (RCRA). Advanced technologies can reduce these costs, but UF{sub 6} disposal still represents large future costs. This paper describes an application for depleted uranium in which depleted uranium hexafluoride is converted into an oxide and then into a heavy aggregate. The heavy uranium aggregate is combined with conventional concrete materials to form an ultra high density concrete, DUCRETE, weighing more than 400 lb/ft{sup 3}. DUCRETE can be used as shielding in spent nuclear fuel/high-level waste casks at a cost comparable to the lower of the disposal cost estimates. Consequently, the case can be made that DUCRETE shielded casks are an alternative to disposal. In this case, a beneficial long term solution is attained for much less than the combined cost of independently providing shielded casks and disposing of the depleted uranium. Furthermore, if disposal is avoided, the political problems associated with selection of a disposal location are also avoided. Other studies have also shown cost benefits for low level waste shielded disposal containers.

The physical and chemical properties of uranium hexafluoride

International Nuclear Information System (INIS)

Barber, E.J.

1988-01-01

This paper describes what uranium hexafluoride (UF 6 ) is, gives some of its pertinent physical properties, illustrates significant reactions between UF 6 and other substances, touches on its toxic properties, and states some of the ''do's'' and ''don't's'' of UF 6 handling. The properties of UF 6 determine how it must be handled and make direct observation impossible. To determine that the material in a container is UF 6 , one must use other instruments in addition to a scale. Because of the very large volume expanision of UF 6 upon melting, diligence must be exercised in filling cylinders in which the UF 6 is partially solidified. A cylinder of liquified UF 6 with no ullage is potentially the equivalent of a superheated hot water heater, not just a hydraulically overpressurized cylinder. Finally, UF 6 can be handled safely by careful attention to the suggested precautions. 9 refs., 2 tabs., 3 figs

A system for the synthesis of uranium hexafluoride by high pressure fluorination of uranium oxides

International Nuclear Information System (INIS)

Elizalde T, J.; Saniger B, J.M.; Nava S, R.

1986-01-01

An equipment for the synthesis of uranium hexafluoride by a direct fluorination method is reported. The equipment is composed by a gaseous fluorine supply, a gas burette, a reactor tube inside a protective shield, a soda-lime chemical trap and a vacuum system. The fluorination is accomplished at a pressure of about 70 kg/cm 2 (1000 lb in 2 ), using gaseous fluorine. (Author). 5 refs, 4 figs, 2 tabs

Uranium hexafluoride packaging tiedown systems overview at Portsmouth Gaseous Diffusion Plant, Piketon, Ohio

International Nuclear Information System (INIS)

Becker, D.L.; Green, D.J.; Lindquist, M.R.

1993-07-01

The Portsmouth Gaseous Diffusion Plant (PORTS) in Piketon, Ohio, is operated by Martin Marietta Energy Systems, Inc., through the US Department of Energy-Oak Ridge Operations Office (DOE-ORO) for the US Department of Energy-Headquarters, Office of Nuclear Energy. The PORTS conducts those operations that are necessary for the production, packaging, and shipment of uranium hexafluoride (UF 6 ). Uranium hexafluoride enriched uranium than 1.0 wt percent 235 U shall be packaged in accordance with the US Department of Transportation (DOT) regulations of Title 49 CFR Parts 173 (Reference 1) and 178 (Reference 2), or in US Nuclear Regulatory Commission (NRC) or US Department of Energy (DOE) certified package designs. Concerns have been expressed regarding the various tiedown methods and condition of the trailers being used by some shippers/carriers for international transport of the UF 6 cylinders/overpacks. Because of the concerns about international shipments, the US Department of Energy-Headquarters (DOE-HQ) Office of Nuclear Energy, through DOE-HQ Transportation Management Division, requested Westinghouse Hanford Company (Westinghouse Hanford) to review UF 6 packaging tiedown and shipping practices used by PORTS, and where possible and appropriate, provide recommendations for enhancing these practices. Consequently, a team of two individuals from Westinghouse Hanford visited PORTS on March 5 and 6, 1990, for the purpose of conducting this review. The paper provides a brief discussion of the review activities and a summary of the resulting findings and recommendations. A detailed reporting of the is documented in Reference 4

Uranium hexafluoride production plant decommissioning

International Nuclear Information System (INIS)

Santos, Ivan

2008-01-01

The Institute of Energetic and Nuclear Research - IPEN is a research and development institution, located in a densely populated area, in the city of Sao Paulo. The nuclear fuel cycle was developed from the Yellow Cake to the enrichment and reconversion at IPEN. After this phase, all the technology was transferred to private enterprises and to the Brazilian Navy (CTM/SP). Some plants of the fuel cycle were at semi-industrial level, with a production over 20 kg/h. As a research institute, IPEN accomplished its function of the fuel cycle, developing and transferring technology. With the necessity of space for the implementation of new projects, the uranium hexafluoride (UF 6 ) production plant was chosen, since it had been idle for many years and presented potential leaking risks, which could cause environmental aggression and serious accidents. This plant decommission required accurate planning, as this work had not been carried out in Brazil before, for this type of facility, and there were major risks involving gaseous hydrogen fluoride aqueous solution of hydrofluoric acid (HF) both highly corrosive. Evaluations were performed and special equipment was developed, aiming to prevent leaking and avoid accidents. During the decommissioning work, the CNEN safety standards were obeyed for the whole operation. The environmental impact was calculated, showing to be not relevant.The radiation doses, after the work, were within the limits for the public and the area was released for new projects. (author)

Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids - Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method

International Nuclear Information System (INIS)

2004-01-01

This first edition of ISO 7097-1 together with ISO 7097-2:2004 cancels and replaces ISO 7097:1983, which has been technically revised, and ISO 9989:1996. ISO 7097 consists of the following parts, under the general title Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids: Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method; Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method. This part 2. of ISO 7097 describes procedures for determination of uranium in solutions, uranium hexafluoride and solids. The procedures described in the two independent parts of this International Standard are similar: this part uses a titration with cerium(IV) and ISO 7097-1 uses a titration with potassium dichromate

Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids - Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method

International Nuclear Information System (INIS)

2004-01-01

This first edition of ISO 7097-1 together with ISO 7097-2:2004 cancels and replaces ISO 7097:1983, which has been technically revised, and ISO 9989:1996. ISO 7097 consists of the following parts, under the general title Nuclear fuel technology - Determination of uranium in solutions, uranium hexafluoride and solids: Part 1: Iron(II) reduction/potassium dichromate oxidation titrimetric method; Part 2: Iron(II) reduction/cerium(IV) oxidation titrimetric method. This part 1. of ISO 7097 describes procedures for the determination of uranium in solutions, uranium hexafluoride and solids. The procedures described in the two independent parts of this International Standard are similar: this part uses a titration with potassium dichromate and ISO 7097-2 uses a titration with cerium(IV)

Moderation control in low enriched 235U uranium hexafluoride packaging operations and transportation

International Nuclear Information System (INIS)

Dyer, R.H.; Kovac, F.M.; Pryor, W.A.

1993-01-01

Moderation control is the basic parameter for ensuring nuclear criticality safety during the packaging and transport of low 235 U enriched uranium hexafluoride before its conversion to nuclear power reactor fuel. Moderation control has permitted the shipment of bulk quantities in large cylinders instead of in many smaller cylinders and, therefore, has resulted in economies without compromising safety. Overall safety and uranium accountability have been enhanced through the use of the moderation control. This paper discusses moderation control and the operating procedures to ensure that moderation control is maintained during packaging operations and transportation

Fire testing of bare uranium hexafluoride cylinders

Energy Technology Data Exchange (ETDEWEB)

Pryor, W.A. [PAI Corp., Oak Rige, TN (United States)

1991-12-31

In 1965, the Oak Ridge Gaseous Diffusion Plant (ORGDP), now the K-25 Site, conducted a series of tests in which bare cylinders of uranium hexafluoride (UF{sub 6}) were exposed to engulfing oil fires for the US Atomic Energy Commission (AEC), now the US Department of Energy (DOE). The tests are described and the results, conclusions, and observations are presented. Two each of the following types of cylinders were tested: 3.5-in.-diam {times} 7.5-in.-long cylinders of Monel (Harshaw), 5.0-in.-diam {times} 30-in.-long cylinders of Monel, and 8-in.-diam {times} 48-in.-long cylinders of nickel. The cylinders were filled approximately to the standard UF{sub 6} fill limits of 5, 55, and 250 lb, respectively, with a U-235 content of 0.22%. The 5-in.- and 8-in.-diam cylinders were tested individually with and without their metal valve covers. For the 3.5-in.-diam Harshaw cylinders and the 5.0-in.-diam cylinder without a valve cover the valves failed and UF{sub 6} was released. The remaining cylinders ruptured explosively in time intervals ranging from about 8.5 to 11 min.

Fire testing of bare uranium hexafluoride cylinders

Energy Technology Data Exchange (ETDEWEB)

Pryor, W.A. [PAI Corp., Oak Ridge, TN (United States)

1991-12-31

In 1965, the Oak Ridge Gaseous Diffusion Plant (ORGDP), now the K-25 Site, conducted a series of tests in which bare cylinders of uranium hexafluoride (UF{sub 6}) were exposed to engulfing oil fires for the US Atomic Energy Commission (AEC), now the US Department of Energy (DOE). The tests are described and the results, conclusions, and observations are presented. Two each of the following types of cylinders were tested: 3.5-in.-diam {times} 7.5-in.-long cylinders of Monel (Harshaw), 5.0-in.-diam {times} x 30-in.-long cylinders of Monel, and 8-in.-diam {times} 48-in.-long cylinders of nickel. The cylinders were filled approximately to the standard UF{sub 6} fill limits of 5, 55, and 250 lb, respectively, with a U-235 content of 0.22%. The 5-in.- and 8-in.-diam cylinders were tested individually with and without their metal valve covers. For the 3.5-in.-diam Harshaw cylinders and the 5.0-in.-diam cylinder without a valve cover, the valves failed and UF{sub 6} was released. The remaining 6 cylinders ruptured explosively in time intervals ranging from about 8.5 to 11 min.

Bentonite clay purification for development of polymeric nan composites using a single screw extruder; Purificacao de argila bentonita para desenvolvimento de nanocomposito polimerico utilizando uma extrusora rosca simples

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-07-01

In this work, a bentonite clay rich in montmorillonite was purified and chemical treat to be used in the development of poly (methyl methacrylate) /clay nanocomposites via melting processes. After the clay treatment and purification, a masterbatch with 25% clay and 75% PMMA was produced by solution technique, using acetone as solvent. For produce samples with 2.5% clay, the masterbatch along with pure polymer were added and mixed in single screw extruder with a diameter of 16 mm and W/D 26. X-rays diffractometry (XRD) and X-rays fluorescence (XRF). Tests were performed to evaluate and characterizing the bentonite clay used in the development of this work and differential scanning calorimetry (DSC) tests were performed to evaluate changes in the thermal properties of the nanocomposites produced. (author)

Metal-free reduction of the greenhouse gas sulfur hexafluoride, formation of SF5 containing ion pairs and the application in fluorinations

KAUST Repository

Rueping, Magnus; Nikolaienko, Pavlo; Lebedev, Yury; Adams, Alina

2017-01-01

A protocol for the fast and selective two-electron reduction of the potent greenhouse gas sulfur hexafluoride (SF6) by organic electron donors at ambient temperature has been developed. The reaction yields solid ion pairs consisting of donor

Management of wastes from the refining and conversion of uranium ore concentrate to uranium hexafluoride

International Nuclear Information System (INIS)

1981-01-01

This report is the outcome of an IAEA Advisory Group Meeting on ''Waste Management Aspects in Relation to the Refining of Uranium Ore Concentrates and their Conversion to Uranium Hexafluoride'', which was held in Vienna from 17 to 21 December 1979. The report summarizes the main topics discussed at the meeting and gives an overview of uranium refining processes, being used in nuclear industry. The meeting was organized by the International Atomic Energy Agency, Radioactive Waste Management Section

Uranium hexafluoride packaging tiedown systems overview at Portsmouth Gaseous Diffusion Plant, Piketon, Ohio

International Nuclear Information System (INIS)

Becker, D.L.; Lindquist, M.R.

1993-01-01

The Portsmouth Gaseous Diffusion Plant (PORTS) in Piketon, Ohio, is operated by Martin Marietta Energy Systems, Inc., through the US Department of Energy-Oak Ridge Operations Office (DOE-ORO) for the US Department of Energy-Headquarters, Office of Nuclear Energy. The PORTS conducts those operations that are necessary for the production, packaging, and shipment of enriched uranium hexafluoride (UF 6 ). Uranium hexafluoride enriched greater than 1.0 wt percent 235 U shall be packaged in accordance with the US Department of Transportation (DOT) regulations of Title 49 CFR Parts 173 and 178, or in US Nuclear Regulatory Commission (NRC) or US Department of Energy (DOE) certified package designs. Concerns have been expressed regarding the various tiedown methods and condition of the trailers being used by some shippers/carriers for international transport of the UF 6 cylinders/overpacks. International shipments typically are not made using dedicated trailers, and numerous trailers have been received at PORTS with improperly and potentially dangerously secured overpacks. Because of the concerns about international shipments, the US Department of Energy-Headquarters (DOE-HQ) Office of Nuclear Energy, through DOE-HQ Transportation Management Division, requested Westinghouse Hanford Company (Westinghouse Hanford) to review UF 6 packaging tiedown and shipping practices used by PORTS; and where possible and appropriate, provide recommendations for enhancing these practices. Consequently, a team of two individuals from Westinghouse Hanford visited PORTS on March 5 and 6, 1990, for the purpose of conducting this review. The paper provides a brief discussion of the review activities and a summary of the resulting findings and recommendations

Standard test methods for arsenic in uranium hexafluoride

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 These test methods are applicable to the determination of total arsenic in uranium hexafluoride (UF6) by atomic absorption spectrometry. Two test methods are given: Test Method A—Arsine Generation-Atomic Absorption (Sections 5-10), and Test Method B—Graphite Furnace Atomic Absorption (Appendix X1). 1.2 The test methods are equivalent. The limit of detection for each test method is 0.1 μg As/g U when using a sample containing 0.5 to 1.0 g U. Test Method B does not have the complete collection details for precision and bias data thus the method appears as an appendix. 1.3 Test Method A covers the measurement of arsenic in uranyl fluoride (UO2F2) solutions by converting arsenic to arsine and measuring the arsine vapor by flame atomic absorption spectrometry. 1.4 Test Method B utilizes a solvent extraction to remove the uranium from the UO2F2 solution prior to measurement of the arsenic by graphite furnace atomic absorption spectrometry. 1.5 Both insoluble and soluble arsenic are measured when UF6 is...

Standard practice for bulk sampling of liquid uranium hexafluoride

CERN Document Server

American Society for Testing and Materials. Philadelphia

2001-01-01

1.1 This practice covers methods for withdrawing representative samples of liquid uranium hexafluoride (UF6) from bulk quantities of the material. Such samples are used for determining compliance with the applicable commercial specification, for example Specification C787 and Specification C996. 1.2 It is assumed that the bulk liquid UF6 being sampled comprises a single quality and quantity of material. This practice does not address any special additional arrangements that might be required for taking proportional or composite samples, or when the sampled bulk material is being added to UF6 residues already in a container (“heels recycle”). 1.3 The number of samples to be taken, their nominal sample weight, and their disposition shall be agreed upon between the parties. 1.4 The scope of this practice does not include provisions for preventing criticality incidents. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of th...

Parametric analyses of planned flowing uranium hexafluoride critical experiments

Science.gov (United States)

Rodgers, R. J.; Latham, T. S.

1976-01-01

Analytical investigations were conducted to determine preliminary design and operating characteristics of flowing uranium hexafluoride (UF6) gaseous nuclear reactor experiments in which a hybrid core configuration comprised of UF6 gas and a region of solid fuel will be employed. The investigations are part of a planned program to perform a series of experiments of increasing performance, culminating in an approximately 5 MW fissioning uranium plasma experiment. A preliminary design is described for an argon buffer gas confined, UF6 flow loop system for future use in flowing critical experiments. Initial calculations to estimate the operating characteristics of the gaseous fissioning UF6 in a confined flow test at a pressure of 4 atm, indicate temperature increases of approximately 100 and 1000 K in the UF6 may be obtained for total test power levels of 100 kW and 1 MW for test times of 320 and 32 sec, respectively.

Isotopic analysis of uranium hexafluoride highly enriched in U-235

International Nuclear Information System (INIS)

Chaussy, L.; Boyer, R.

1968-01-01

Isotopic analysis of uranium in the form of the hexafluoride by mass-spectrometry gives gross results which are not very accurate. Using a linear interpolation method applied to two standards it is possible to correct for this inaccuracy as long as the isotopic concentrations are less than about 10 per cent in U-235. Above this level, the interpolations formula overestimates the results, especially if the enrichment of the analyzed samples is higher than 1.3 with respect to the standards. A formula is proposed for correcting the interpolation equation and for the extending its field of application to high values of the enrichment (≅2) and of the concentration. It is shown that by using this correction the results obtained have an accuracy which depends practically only on that of the standards, taking into account the dispersion in the measurements. (authors) [fr

Assessment of the risk of transporting uranium hexafluoride by truck and train

International Nuclear Information System (INIS)

Geffen, C.A.; Johnson, J.F.; Davis, D.K.; Friley, J.R.; Ross, B.A.

1978-08-01

This report is the fifth in a series of studies of the risk of transporting potentially hazardous energy materials. The report presents an assessment of the risk of shipping uranium hexafluoride (UF 6 ) by truck and rail. The general risk assessment methodology, summarized in Section 3, used in this study is that developed for the first study in this series. The assessment includes the risks from release of uranium hexafluoride during truck or rail transport due to transportation accidents. The contribution to the risk of deteriorated or faulty packaging during normal transport was also considered. The report is sectioned to correspond to the specific analysis steps of the risk assessment model. The transportation system and accident environment are described in Sections 4 and 5. Calculation of the response of the shipping system to forces produced in transportation accidents are presented in Section 6 and the results of a survey to determine the condition of the package during transport are presented in Section 7. Sequences of events that could lead to a release of radioactive material from the shipping cask during transportation are postulated in Section 8 using fault tree analysis. These release sequences are evaluated in Sections 9 through 11, to determine both the likelihood and the possible consequences of each release. Supportive data and analyses are given in the appendices. The results of the risk assessment have been related to the year 1985, when it is projected that 100 GW of electric power will be generated annually by nuclear power plants. It was estimated that approximately 46,000 metric tons (MT) of natural UF 6 and 14,600 MT of enriched UF 6 would be shipped in the reference year

Preparation of plutonium hexafluoride. Recovery of plutonium from waste dross (1962); Preparation de l'hexafluorure de plutonium. Recuperation du plutonium des scories d'elaboration (1962)

Energy Technology Data Exchange (ETDEWEB)

Gendre, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-01

The object of this work is to study the influence of various physical factors on the rate of fluorination of solid plutonium tetrafluoride by fluorine. In a horizontal oven with a circulation for pure fluorine at atmospheric pressure and 520 deg. C, at a fluorine rate of 9 litres/hour, it is possible to transform 3 g of tetrafluoride to hexafluoride with about 100 per cent transformation and a recovery yield of over 90 per cent, in 4 to 5 hours. The fluorination rate is a function of the temperature, of the fluorine flow-rate, of the crucible surface, of the depth of the tetrafluoride layer and of the reaction time. It does not depend on the diffusion of the fluorine into the solid but is determined by the reaction at the gas-solid interface and obeys the kinetic law (1 - T{sub T}){sup 1/3} = kt + 1. The existence of intermediate fluorides, in particular Pu{sub 4} F{sub 17}, is confirmed by a break in the Arrhenius plot at about 370 deg. C, by differences in the fluorination rates inside the tetrafluoride layer, and by reversible colour changes. The transformation to hexafluoride occurs with a purification with respect of the foreign elements present in the initial plutonium. Recovery of plutonium from waste dross: The study is based on the transformation of occluded plutonium particles to gaseous hexafluoride which is then decomposed thermally to the tetrafluoride which can be reintroduced directly in the production circuit. Under the conditions considered this process is not applicable industrially. After milling, it is possible to separate the dross into enriched (75 per cent Pu in 2.6 per cent by weight of dross) and depleted portions. By prolonged fluorination (16 hours) of the various fractions it is possible to recover about 80 per cent of the plutonium. A treatment plant using fluidization, as described at the end of this study, should make it possible to substantially improve the yield. (author) [French] L'objet de l'etude est l'influence des differents

Process for decontamination of surfaces in an facility of natural uranium hexafluoride production (UF6)

International Nuclear Information System (INIS)

Almeida, Claudio C. de; Silva, Teresinha M.; Rodrigues, Demerval L.; Carneiro, Janete C.G.G.

2017-01-01

The experience acquired in the actions taken during the decontamination process of an IPEN-CNEN / SP Nuclear and Energy Research Institute facility, for the purpose of making the site unrestricted, is reported. The steps of this operation involved: planning, training of facility operators, workplace analysis and radiometric measurements. The facility had several types of equipment from the natural uranium hexafluoride (UF 6 ) production tower and other facility materials. Rules for the transportation of radioactive materials were established, both inside and outside the facility and release of materials and installation

Metal-free reduction of the greenhouse gas sulfur hexafluoride, formation of SF5 containing ion pairs and the application in fluorinations

KAUST Repository

Rueping, Magnus

2017-05-04

A protocol for the fast and selective two-electron reduction of the potent greenhouse gas sulfur hexafluoride (SF6) by organic electron donors at ambient temperature has been developed. The reaction yields solid ion pairs consisting of donor dications and SF5-anions which can be effectively used in fluorination reactions.

Chemisorption of uranium hexa-fluoride on sodium fluoride pellets

Energy Technology Data Exchange (ETDEWEB)

Kalburgi, A K; Sanyal, A; Puranik, V D; Bhattacharjee, B [Chemical Technology Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

This paper comprises kinetics of chemical reaction or rather chemisorption of uranium hexafluoride gas on sodium fluoride pellets. The chemisorption is essentially irreversible at room temperature, while the process reverses at high temperature above 280 deg C. This chemisorption process was experimentally conducted in static condition at room temperature and its kinetics was studied. In the experiments, practically pure UF{sub 6} was used and the effects of gas pressure and weight of NaF pellets, were studied. In this heterogenous reaction, in which diffusion through ash layer is followed by chemical reaction, the reaction part is instantaneous and is first order with respect to gas concentration. Since the process of chemisorption is not only pure chemical reaction but also gas diffusion through ash layer, the rate constant depreciates with the percentage loading of UF{sub 6} on NaF pellets. The kinetic equation for the above process has been established for a particular size of NaF pellets and pellet porosity. (author). 5 refs., 3 figs., 3 tabs.

Minimizing the risk and impact of uranium hexafluoride production

International Nuclear Information System (INIS)

Clark, D.R.; Kennedy, T.W.

2010-01-01

Cameco Corporation's Port Hope conversion facility, situated on the shore of Lake Ontario in the Municipality of Port Hope, Ontario, Canada, converts natural uranium trioxide (UO_3) into uranium dioxide (UO_2) or natural uranium hexafluoride (UF_6). Conversion of UO_3 to UF_6 has been undertaken at the Port Hope conversion facility since 1970 and is currently carried out in a second-generation plant licensed to annually produce 12,500 tonnes U as UF_6. Consistent with Cameco's vision, values and measures of success, Cameco recognizes safety and health of its workers and the public, protection of the environment, and the quality of our processes as the highest corporate priorities. Production of UF_6 in a brownfield urban setting requires a commitment to design, build and maintain multiple layers of containment (defence-in-depth) and to continually improve in all operational aspects to achieve this corporate commitment. This paper will describe the conversion processes utilized with a focus on the cultural, management and physical systems employed to minimize the risk and impact of the operation. (author)

Effect of charcoal on water purification

OpenAIRE

Suzuki, Hirotaka; Kawahigashi, Tatsuo

2014-01-01

[Abstract] A natural basin system purifies water through self-purification, but the water pollution load of a river might exceed its self-purification capacity. Charcoal, which is used for other uses aside from heating, such as air purification, was evaluated experimentally for water quality purification. The experiment described herein is based on simple water quality measurements. Some experimentally obtained results are discussed.

The bubble method of water purification

Science.gov (United States)

Smirnov, B. M.; Babaeva, N. Yu.; Naidis, G. V.; Panov, V. A.; Saveliev, A. S.; Son, E. E.; Tereshonok, D. V.

2018-02-01

The processes of water purification from admixture molecules are analyzed. The purification rate is limited due to a low diffusion coefficient of the admixture molecules in water. At non-small concentrations of the admixture molecules, the water purication can proceed through association of molecules in condensed nanoparticles which fall on the bottom of the water volume. The rate of association may be increased in an external electric field, but in reality this cannot change significantly the rate of the purification process. The bubble method of water purification is considered, where air bubbles formed at the bottom of the water volume, transfer admixture molecules to the interface. This method allows one to clean small water volumes fast. This mechanism of water purification is realized experimentally and exhibits the promises of the bubble purification method.

Statistical and Judgmental Criteria for Scale Purification

DEFF Research Database (Denmark)

Wieland, Andreas; Durach, Christian F.; Kembro, Joakim

2017-01-01

of scale purification, to critically analyze the current state of scale purification in supply chain management (SCM) research and to provide suggestions for advancing the scale-purification process. Design/methodology/approach A framework for making scale-purification decisions is developed and used...

Preconceptual design studies and cost data of depleted uranium hexafluoride conversion plants

International Nuclear Information System (INIS)

Jones, E

1999-01-01

One of the more important legacies left with the Department of Energy (DOE) after the privatization of the United States Enrichment Corporation is the large inventory of depleted uranium hexafluoride (DUF6). The DOE Office of Nuclear Energy, Science and Technology (NE) is responsible for the long-term management of some 700,000 metric tons of DUF6 stored at the sites of the two gaseous diffusion plants located at Paducah, Kentucky and Portsmouth, Ohio, and at the East Tennessee Technology Park in Oak Ridge, Tennessee. The DUF6 management program resides in NE's Office of Depleted Uranium Hexafluoride Management. The current DUF6 program has largely focused on the ongoing maintenance of the cylinders containing DUF6. However, the long-term management and eventual disposition of DUF6 is the subject of a Programmatic Environmental Impact Statement (PEIS) and Public Law 105-204. The first step for future use or disposition is to convert the material, which requires construction and long-term operation of one or more conversion plants. To help inform the DUF6 program's planning activities, it was necessary to perform design and cost studies of likely DUF6 conversion plants at the preconceptual level, beyond the PEIS considerations but not as detailed as required for conceptual designs of actual plants. This report contains the final results from such a preconceptual design study project. In this fast track, three month effort, Lawrence Livermore National Laboratory and Bechtel National Incorporated developed and evaluated seven different preconceptual design cases for a single plant. The preconceptual design, schedules, costs, and issues associated with specific DUF6 conversion approaches, operating periods, and ownership options were evaluated based on criteria established by DOE. The single-plant conversion options studied were similar to the dry-conversion process alternatives from the PEIS. For each of the seven cases considered, this report contains information on

Determination of the isotopic ratio 235U/238U in UF6 using quadrupole mass spectrometry

International Nuclear Information System (INIS)

Kusahara, Helena Sueco

1979-01-01

In this work measurements of isotope ratios 235 U / 23 '8U in uranium hexafluoride are carried out using a quadrupole mass spectrometer. The operational parameters, which affect the final precision of the results, are standardized. Optimized procedures for the preparation of uranium hexafluoride samples by fluorination of uranium oxides using cobalt trifluoride method are established. Careful attention is given to the process of purification of uranium hexafluoride samples by fractional distillation. Adequate statistical methods for analysing the results obtained for single ratio measurements as well as the ratio ' of isotopic ratios of sample and standard ar.e developed. A precision of about 10 -4 for single ratio measurements and accuracy of about 0,3% for the ratio of sample and standard ratios are obtained. These results agree with the values which have been obtained using magnetic mass spectrometers. The procedures and methods established in this work can be employed in the systematic uranium isotope analysis in UF 6 form. (author)

Estimates of health risks associated with uranium hexafluoride transport by air

International Nuclear Information System (INIS)

Elert, M.; Skagius, K.

1990-01-01

In Sweden air transport is considered as an alternative for the shipment of uranium hexafluoride (UF 6 ). The radiological consequences of an aeroplane accident involving UF 6 transport have been estimated and are presented as the dose from acute exposure and the dose from long-term exposure caused by ground contamination. Chemical effects of a UF 6 release are also discussed. A number of limiting scenarios have been defined, resulting in different mechanical and thermal impacts on the transport packages. The expected accident environment and the physical and chemical behaviour of the material have been used to derive a source term for the release to the air. A Gaussian dispersion model has been used to calculate the expected air concentration downwind from the accident site. The radiation dose from short-term exposure was found to be higher than the long-term exposure from uranium deposited on the ground. (author)

Purification of Water by Aquatic Plants

OpenAIRE

Morimitsu, Katsuhito; Kawahigashi, Tatsuo

2013-01-01

[Abstract] Water quality purification of many water systems including those occurring in rivers depends to a great degree on water quality purification activities of aquatic plants and microbes. This paper presents a discussion of results, based on laboratory experiments, of purification by aquatic plants.

Comparing Russian and Finnish standards of water purification

OpenAIRE

Maria, Pupkova

2012-01-01

The subject of this thesis is water purification. The first aim of this thesis is to consider different ways of water purification. The second aim is to compare Finnish and Russian standards of water purification. The third one is to show water purification methods on the pattern of Mikkeli water purification plan. Water purification methods of water intended for human consumption will be described.Combined tables will be done according to the quality requirement of drinking water of both,...

Uranium hexafluoride: Handling procedures and container descriptions

International Nuclear Information System (INIS)

1987-09-01

The US Department of Energy (DOE) guidelines for packaging, measuring, and transferring uranium hexafluoride (UF 6 ) have been undergoing continual review and revision for several years to keep them in phase with developing agreements for the supply of enriched uranium. Initially, K-1323 ''A Brief Guide to UF 6 Handling,'' was issued in 1957. This was superceded by ORO-651, first issued in 1966, and reissued in 1967 to make editorial changes and to provide minor revisions in procedural information. In 1968 and 1972, Revisions 2 and 3, respectively, were issued as part of the continuing effort to present updated information. Revision 4 issued in 1977 included revisions to UF 6 cylinders, valves, and methods to use. Revision 5 adds information dealing with pigtails, overfilled cylinders, definitions and handling precautions, and cylinder heel reduction procedures. Weighing standards previously presented in ORO-671, Vol. 1 (Procedures for Handling and Analysis of UF 6 ) have also been included. This revision, therefore, supercedes ORO-671-1 as well as all prior issues of this report. These guidelines will normally apply in all transactions involving receipt or shipment of UF 6 by DOE, unless stipulated otherwise by contracts or agreements with DOE or by notices published in the Federal Register. Any questions or requests for additional information on the subject matter covered herein should be directed to the United States Department of Energy, P.O. Box E, Oak Ridge, Tennessee 37831, Attention: Director, Uranium Enrichment Operations Division. 33 figs., 12 tabs

Strep-Tagged Protein Purification.

Science.gov (United States)

Maertens, Barbara; Spriestersbach, Anne; Kubicek, Jan; Schäfer, Frank

2015-01-01

The Strep-tag system can be used to purify recombinant proteins from any expression system. Here, protocols for lysis and affinity purification of Strep-tagged proteins from E. coli, baculovirus-infected insect cells, and transfected mammalian cells are given. Depending on the amount of Strep-tagged protein in the lysate, a protocol for batch binding and subsequent washing and eluting by gravity flow can be used. Agarose-based matrices with the coupled Strep-Tactin ligand are the resins of choice, with a binding capacity of up to 9 mg ml(-1). For purification of lower amounts of Strep-tagged proteins, the use of Strep-Tactin magnetic beads is suitable. In addition, Strep-tagged protein purification can also be automated using prepacked columns for FPLC or other liquid-handling chromatography instrumentation, but automated purification is not discussed in this protocol. The protocols described here can be regarded as an update of the Strep-Tag Protein Handbook (Qiagen, 2009). © 2015 Elsevier Inc. All rights reserved.

Recovery of thorium and rare earths by their peroxides precipitation from a residue produced in the thorium purification facility; Recuperacao de torio e terras raras via peroxido do residuo originado na unidade de purificacao de torio

Energy Technology Data Exchange (ETDEWEB)

Freitas, Antonio Alves de

2008-07-01

As consequence of the operation of a Thorium purification facility, for pure Thorium Nitrate production, the IPEN (Instituto de Pesquisas Energeticas e Nucleares) has stored away a solid residue called RETOTER (REsiduo de TOrio e TErras Raras). The RETOTER is rich in Rare-Earth Elements and significant amount of Thorium-232 and minor amount of Uranium. Furthermore it contains several radionuclides from the natural decay series. Significant radioactivity contribution is generated by the Thorium descendent, mainly the Radium-228(T{sub 1/2}=5.7y), known as meso thorium and Thorium-228(T{sub 1/2} 1.90y). An important thorium daughter is the Lead-208, a stable isotope present with an expressive quantity. After the enclosure of the operation of the Thorium purification facility, many researches have been developed for the establishment of methodologies for recovery of Thorium, Rare-Earth Elements and Lead-208 from the RETOTER. This work presents a method for RETOTER decontamination, separating and bordering upon some radioactive isotopes. The residue was digested with nitric acid and the Radium-228 was separated by the Barium Sulphate co-precipitation procedure. Finally, the Thorium was separated by the peroxide precipitation and the Rare-Earth Elements were also recovered by the Rare-Earth peroxide precipitation in the filtrate solution.(author)

Uranium fluoride chemistry. Part 1. The gas phase reaction of uranium hexafluoride with alcohols

International Nuclear Information System (INIS)

Schnautz, N.G.; Venter, P.J.

1992-01-01

The reaction between uranium hexafluoride (UF 6 ) and simple alcohols in the gas phase was observed to proceed by way of three possible reaction pathways involving dehydration, deoxygenative fluorination, and ether formation. These reactions can best be explained by assuming that alcohols first react with UF 6 to afford the alkoxy uranium pentafluoride intermediate ROUF 5 , which reacts further to give the dehydration, deoxygenative fluorination, and ether products. In each of the above three reaction pathways, UF 6 is transformed to UOF 4 , which being as reactive toward alcohols as UF 6 , reacts further with the alcohol in question to finally afford the unreactive uranyl fluoride (UO 2 F 2 ). 6 refs., 2 tabs

Including environmental concerns in management strategies for depleted uranium hexafluoride

International Nuclear Information System (INIS)

Goldberg, M.; Avci, H.I.; Bradley, C.E.

1995-01-01

One of the major programs within the Office of Nuclear Energy, Science, and Technology of the US Department of Energy (DOE) is the depleted uranium hexafluoride (DUF 6 ) management program. The program is intended to find a long-term management strategy for the DUF 6 that is currently stored in approximately 46,400 cylinders at Paducah, KY; Portsmouth, OH; and Oak Ridge, TN, USA. The program has four major components: technology assessment, engineering analysis, cost analysis, and the environmental impact statement (EIS). From the beginning of the program, the DOE has incorporated the environmental considerations into the process of strategy selection. Currently, the DOE has no preferred alternative. The results of the environmental impacts assessment from the EIS, as well as the results from the other components of the program, will be factored into the strategy selection process. In addition to the DOE's current management plan, other alternatives continued storage, reuse, or disposal of depleted uranium, will be considered in the EIS. The EIS is expected to be completed and issued in its final form in the fall of 1997

Uranium hexafluoride: A manual of good handling practices. Revision 7

International Nuclear Information System (INIS)

1995-01-01

The United States Enrichment Corporation (USEC) is continuing the policy of the US Department of Energy (DOE) and its predecessor agencies in sharing with the nuclear industry their experience in the area of uranium hexafluoride (UF 6 ) shipping containers and handling procedures. The USEC has reviewed Revision 6 or ORO-651 and is issuing this new edition to assure that the document includes the most recent information on UF 6 handling procedures and reflects the policies of the USEC. This manual updates the material contained in earlier issues. It covers the essential aspects of UF 6 handling, cylinder filling and emptying, general principles of weighing and sampling, shipping, and the use of protective overpacks. The physical and chemical properties of UF 6 are also described. The procedures and systems described for safe handling of UF 6 presented in this document have been developed and evaluated during more than 40 years of handling vast quantities of UF 6 . With proper consideration for its nuclear properties, UF 6 may be safely handled in essentially the same manner as any other corrosive and/or toxic chemical

Rapid purification of recombinant histones.

Science.gov (United States)

Klinker, Henrike; Haas, Caroline; Harrer, Nadine; Becker, Peter B; Mueller-Planitz, Felix

2014-01-01

The development of methods to assemble nucleosomes from recombinant histones decades ago has transformed chromatin research. Nevertheless, nucleosome reconstitution remains time consuming to this day, not least because the four individual histones must be purified first. Here, we present a streamlined purification protocol of recombinant histones from bacteria. We termed this method "rapid histone purification" (RHP) as it circumvents isolation of inclusion bodies and thereby cuts out the most time-consuming step of traditional purification protocols. Instead of inclusion body isolation, whole cell extracts are prepared under strongly denaturing conditions that directly solubilize inclusion bodies. By ion exchange chromatography, the histones are purified from the extracts. The protocol has been successfully applied to all four canonical Drosophila and human histones. RHP histones and histones that were purified from isolated inclusion bodies had similar purities. The different purification strategies also did not impact the quality of octamers reconstituted from these histones. We expect that the RHP protocol can be readily applied to the purification of canonical histones from other species as well as the numerous histone variants.

The structural second virial coefficient: a spherical-core pair-potential for sulphur hexafluoride

International Nuclear Information System (INIS)

Mohamad Deraman; Powles, J.G.; Dore, J.C.

1984-01-01

Neutron diffraction data for sulphur hexafluoride gas is reanalysed following the same procedure described in our previous paper but using a spherical-core potential which was not considered in that report. The new spherical-core potential, with parameters epsilon/Ksub(B)K = 405, delta/A = 5.042 and α/A = 0.9225, gives a satisfactory fit to both the virial and structural data. There are now three model potentials, a site-site, a LJ 28-7, and this spherical core which all fit the data very well, indeed the core potential reported here fits rather better than the others. The anisotropic site-site potential is still to be preferred on physical grounds but the new core-potential will be useful where an isotopic potential suffices since it is much simpler to use. (author)

Lysine purification with cation exchange resin

International Nuclear Information System (INIS)

Khayati, GH.; Mottaghi Talab, M.; Hamooni Hagheeghat, M.; Fatemi, M.

2003-01-01

L-lysine is an essential amino acid for the growth most of animal species and the number one limiting amino acid for poultry. After production and biomass removal by filtration and centrifugation, the essential next step is the lysine purification and recovery. There are different methods for lysine purification. The ion exchange process is one of the most commonly used purification methods. Lysine recovery was done from broth by ion exchange resin in three different ways: repeated passing, resin soaking and the usual method. Impurities were isolated from the column by repeated wash with distilled water. Recovery and purification was done with NH 4 OH and different alcohol volumes respectively. The results showed that repeated passing is the best method for lysine absorption (maximum range 86.21 %). Washing with alkali solution revealed that most of lysine is obtained in the first step of washing. The highest degree of lysine purification was achieved with the use of 4 volumes of alcohol

Partial Purification and Characterization of Extracellular Protease ...

African Journals Online (AJOL)

Nigerian Journal of Basic and Applied Sciences ... Purification of the enzyme by gel filtration chromatography on Sephadex G75 following ammonium sulphate precipitation gave 2.26 fold increase in purification with specific activity of 46.13 units/mg protein while purification on Sephadex CM50 resulted in reduced ...

Compilation of Requirements for Safe Handling of Fluorine and Fluorine-Containing Products of Uranium Hexafluoride Conversion

International Nuclear Information System (INIS)

Ferrada, J.J.; Hightower, J.R.; Begovich, J.M.

2000-01-01

Public Law (PL) 105--204 requires the U.S. Department of Energy to develop a plan for inclusion in the fiscal year 2000 budget for conversion of the Department's stockpile of depleted uranium hexafluoride (DUF6) to a more stable form over an extended period. The conversion process into a more stable form will produce fluorine compounds (e.g., elemental fluorine or hydrofluoric acid) that need to be handled safely. This document compiles the requirements necessary to handle these materials within health and safety standards, which may apply in order to ensure protection of the environment and the safety and health of workers and the public

Depleted uranium hexafluoride (DUF6) management system--a decision tool

International Nuclear Information System (INIS)

Gasper, J.R.; Sutter, R.J.; Avci, H.I.

1995-01-01

The Depleted Uranium Hexafluoride (DUF 6 ) Management System (DMS) is being developed as a decision tool to provide cost and risk data for evaluation of short-and long-term management strategies for depleted uranium. It can be used to assist decision makers on a programmatic or site-specific level. Currently, the DMS allows evaluation of near-term cylinder management strategies such as storage yard improvements, cylinder restocking, and reconditioning. The DMS has been designed to provide the user with maximum flexibility for modifying data and impact factors (e.g., unit costs and risk factors). Sensitivity analysis can be performed on all key parameters such as cylinder corrosion rate, inspection frequency, and impact factors. Analysis may be conducted on a system-wide, site, or yard basis. The costs and risks from different scenarios may be compared in graphic or tabular format. Ongoing development of the DMS will allow similar evaluation of long-term management strategies such as conversion to other chemical forms. The DMS is a Microsoft Windows 3.1 based, stand-alone computer application. It can be operated on a 486 or faster computer with VGA, 4 MB of RAM, and 10 MB of disk space

Uranium hexafluoride: A manual of good handling practices. Revision 7

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-01

The United States Enrichment Corporation (USEC) is continuing the policy of the US Department of Energy (DOE) and its predecessor agencies in sharing with the nuclear industry their experience in the area of uranium hexafluoride (UF{sub 6}) shipping containers and handling procedures. The USEC has reviewed Revision 6 or ORO-651 and is issuing this new edition to assure that the document includes the most recent information on UF{sub 6} handling procedures and reflects the policies of the USEC. This manual updates the material contained in earlier issues. It covers the essential aspects of UF{sub 6} handling, cylinder filling and emptying, general principles of weighing and sampling, shipping, and the use of protective overpacks. The physical and chemical properties of UF{sub 6} are also described. The procedures and systems described for safe handling of UF{sub 6} presented in this document have been developed and evaluated during more than 40 years of handling vast quantities of UF{sub 6}. With proper consideration for its nuclear properties, UF{sub 6} may be safely handled in essentially the same manner as any other corrosive and/or toxic chemical.

Effects of gamma radiation immunogenicity of ribonucleoprotein (RNPs) of rabies virus and purification of anti-RNPs antibodies for diagnosis; Efeitos da radiacao gama na imunogenicidade das ribonucleoproteinas (RNPs) do virus da raiva e purificacao de anticorpos anti-RNPs para diagnostico

Energy Technology Data Exchange (ETDEWEB)

Costa, Ana Elena Boamorte da

2010-07-01

The World Health Organization recommends the direct immunofluorescence test for laboratory diagnosis and serological evaluation of rabies. To achieve this test, fluorescent anti-ribo nucleoproteins (RNPs) conjugates, produced from purified IgGs of RNP-immunized animals are employed. The aims of the present study were: investigate the effects of gamma radiation on the immunogenicity of RNPs, as well as to compare two chromatographic methodologies for the purification of anti-RNPs immunoglobulins. Sera from animals immunized with either native or irradiated RNPs were compared by direct immunofluorescence and immuno enzymatic assays. Our results indicate that the animals immunized with irradiated antigen requested a lower number of doses to reach high antibody titers. The immunofluorescence assays indicated that the conjugates produced with the anti-irradiated RNPs IgGs showed similar specificity to its anti-native counterpart, but with a higher definition of the virus inclusions. The purification methods were compared by Bradford and electrophoresis assays. According to the results, we concluded that the affinity-based process resulted in higher yields, lower execution time, and higher purity of the antibodies. (author)

Bibliography of electron and photon cross sections with atoms and molecules published in the 20th century. Sulphur hexafluoride

International Nuclear Information System (INIS)

Hayashi, Makoto

2003-05-01

A bibliography of original and review reports of experiments or theories of electron and photon cross sections and also electron swarm data are presented for atomic or molecular species with specified targets. These works covered 17 atoms and 51 molecules. The present bibliography is only for sulphur hexafluoride (SF 6 ). About 920 papers were compiled. A comprehensive author index is included. The bibliography covers the period 1934 through 2000 for SF 6 . Finally, author's comments for SF 6 electron collision cross section are given. (author)

Entanglement purification of multi-mode quantum states

International Nuclear Information System (INIS)

Clausen, J; Knoell, L; Welsch, D-G

2003-01-01

An iterative random procedure is considered allowing entanglement purification of a class of multi-mode quantum states. In certain cases, complete purification may be achieved using only a single signal state preparation. A physical implementation based on beam splitter arrays and non-linear elements is suggested. The influence of loss is analysed in the example of purification of entangled N-mode coherent states

The various sodium purification techniques

International Nuclear Information System (INIS)

Courouau, J.L.; Masse, F.; Rodriguez, G.; Latge, C.; Redon, B.

1997-01-01

In the framework of sodium waste treatment, the sodium purification phase plays an essential role in the chain of operations leading to the transformation of the active sodium, considered as waste, into a stable sodium salt. The objectives of the purification operations are: To keep a low impurity level, particularly a low concentration in oxygen and hydrogen, in order to allow its transfer to a processing plant, and in order to avoid risks of plugging and/or corrosion in sodium facilities; To reduce the sodium activity in order to limit the dose rate close to the facilities, and in order to reduce the activity of the liquid and gaseous effluents. After a recall of the different kind of impurities that can be present in sodium, and of the different purification methods that could be associated with, the following points are highlighted: (i) Oxygen and hydrogen purification needs, and presentation of some selection criteria for a purification unit adapted to a sodium processing plant, as well as 2 cold trap concepts that are in accordance with these criteria: PSICHOS and PIRAMIDE. (ii) Tritium reduction in a bulk of liquid sodium by swamping, isotopic exchange, or permeation throughout a membrane. (iii) Caesium trapping on carbonaceous matrix. The main matrices used at present are R.V.C. (Reticulated Vitreous Carbon) and Actitex/Pica products. Tests in the laboratory and on an experimental device have demonstrated the performances of these materials, which are able to reduce sodium activity in Cs 134 and Cs 137 to very low values. The sodium purification processes as regards to the hydrogen, oxygen and caesium, that are aimed at facilitating the subsequent treatment of sodium, are therefore mastered operations. Regarding the operations associated with the reduction of the tritium activity, the methods are in the process of being qualified, or to be qualified. (author)

Entanglement of purification: from spin chains to holography

Science.gov (United States)

Nguyen, Phuc; Devakul, Trithep; Halbasch, Matthew G.; Zaletel, Michael P.; Swingle, Brian

2018-01-01

Purification is a powerful technique in quantum physics whereby a mixed quantum state is extended to a pure state on a larger system. This process is not unique, and in systems composed of many degrees of freedom, one natural purification is the one with minimal entanglement. Here we study the entropy of the minimally entangled purification, called the entanglement of purification, in three model systems: an Ising spin chain, conformal field theories holographically dual to Einstein gravity, and random stabilizer tensor networks. We conjecture values for the entanglement of purification in all these models, and we support our conjectures with a variety of numerical and analytical results. We find that such minimally entangled purifications have a number of applications, from enhancing entanglement-based tensor network methods for describing mixed states to elucidating novel aspects of the emergence of geometry from entanglement in the AdS/CFT correspondence.

Bioinspired Materials for Water Purification

Directory of Open Access Journals (Sweden)

Alfredo Gonzalez-Perez

2016-06-01

Full Text Available Water scarcity issues associated with inadequate access to clean water and sanitation is a ubiquitous problem occurring globally. Addressing future challenges will require a combination of new technological development in water purification and environmental remediation technology with suitable conservation policies. In this scenario, new bioinspired materials will play a pivotal role in the development of more efficient and environmentally friendly solutions. The role of amphiphilic self-assembly on the fabrication of new biomimetic membranes for membrane separation like reverse osmosis is emphasized. Mesoporous support materials for semiconductor growth in the photocatalytic degradation of pollutants and new carriers for immobilization of bacteria in bioreactors are used in the removal and processing of different kind of water pollutants like heavy metals. Obstacles to improve and optimize the fabrication as well as a better understanding of their performance in small-scale and pilot purification systems need to be addressed. However, it is expected that these new biomimetic materials will find their way into the current water purification technologies to improve their purification/removal performance in a cost-effective and environmentally friendly way.

Bibliography of electron and photon cross sections with atoms and molecules published in the 20th century. Sulphur hexafluoride

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Makoto [Gaseous Electronics Institute, Nagoya, Aichi (Japan)

2003-05-01

A bibliography of original and review reports of experiments or theories of electron and photon cross sections and also electron swarm data are presented for atomic or molecular species with specified targets. These works covered 17 atoms and 51 molecules. The present bibliography is only for sulphur hexafluoride (SF{sub 6}). About 920 papers were compiled. A comprehensive author index is included. The bibliography covers the period 1934 through 2000 for SF{sub 6}. Finally, author's comments for SF{sub 6} electron collision cross section are given. (author)

Venturi purification device and its application in purification of gaseous waste of nuclear facilities

International Nuclear Information System (INIS)

Kong Jinsong; Yu Ren; Yang Huanlei

2013-01-01

The working principle of Venturi purification device and its purification of aerosol have been described. Then, taking the gaseous iodine as an example, the absorption process of insoluble gas pollutants is discussed, the calculation methods of the gas-liquid contact area, mass transfer rate and efficiency of mass transfer are educed, and the factors that affect the efficiency of mass transfer are analyzed. (authors)

Production of uranium hexafluoride by fluorination tetra-fluoride with elemental fluorine under pressure; Proizvodnja uraovega heksafluorida s tlacnim fluoriranjem uranovega tetrafluorida z elementarnim fluorom

Energy Technology Data Exchange (ETDEWEB)

Lutar, K; Smalc, A; Zemljic, A [Institut Jozef Stefan, Ljubljana (Yugoslavia)

1984-07-01

In the introduction a brief description of some activities of fluorine chemistry department at the J. Stefan Institute is given - from production of elemental fluorine to the investigations in the field of uranium technology. Furthermore, a new method for the production of uranium hexafluoride is described more in detail. The method is based on the fluorination of uranium tetrafluoride with elemental fluorine. (author)

Photocatalytic materials and technologies for air purification.

Science.gov (United States)

Ren, Hangjuan; Koshy, Pramod; Chen, Wen-Fan; Qi, Shaohua; Sorrell, Charles Christopher

2017-03-05

Since there is increasing concern for the impact of air quality on human health, the present work surveys the materials and technologies for air purification using photocatalytic materials. The coverage includes (1) current photocatalytic materials for the decomposition of chemical contaminants and disinfection of pathogens present in air and (2) photocatalytic air purification systems that are used currently and under development. The present work focuses on five main themes. First, the mechanisms of photodegradation and photodisinfection are explained. Second, system designs for photocatalytic air purification are surveyed. Third, the photocatalytic materials used for air purification and their characteristics are considered, including both conventional and more recently developed photocatalysts. Fourth, the methods used to fabricate these materials are discussed. Fifth, the most significant coverage is devoted to materials design strategies aimed at improving the performance of photocatalysts for air purification. The review concludes with a brief consideration of promising future directions for materials research in photocatalysis. Copyright © 2016 Elsevier B.V. All rights reserved.

Surface processes during purification of InP quantum dots

Directory of Open Access Journals (Sweden)

Natalia Mordvinova

2014-08-01

Full Text Available Recently, a new simple and fast method for the synthesis of InP quantum dots by using phosphine as phosphorous precursor and myristic acid as surface stabilizer was reported. Purification after synthesis is necessary to obtain samples with good optical properties. Two methods of purification were compared and the surface processes which occur during purification were studied. Traditional precipitation with acetone is accompanied by a small increase in photoluminescence. It occurs that during the purification the hydrolysis of the indium precursor takes place, which leads to a better surface passivation. The electrophoretic purification technique does not increase luminescence efficiency but yields very pure quantum dots in only a few minutes. Additionally, the formation of In(OH3 during the low temperature synthesis was explained. Purification of quantum dots is a very significant part of postsynthetical treatment that determines the properties of the material. But this subject is not sufficiently discussed in the literature. The paper is devoted to the processes that occur at the surface of quantum dots during purification. A new method of purification, electrophoresis, is investigated and described in particular.

Reuse of ammonium fluoride generated in the uranium hexafluoride conversion

International Nuclear Information System (INIS)

Silva Neto, J.B.; Carvalho, E.F. Urano de; Durazzo, M.; Riella, H.G

2010-01-01

The Nuclear Fuel Centre of IPEN / CNEN - SP develops and manufactures dispersion fuel with high uranium concentration to meet the demand of the IEA-R1 reactor and future research reactors planned to be constructed in Brazil. The fuel uses uranium silicide (U 3 Si 2 ) dispersed in aluminum. For producing the fuel, the processes for uranium hexafluoride (UF 6 ) conversion consist in obtaining U 3 Si 2 and / or U 3 O 8 through the preparation of intermediate compounds, among them ammonium uranyl carbonate - AUC, ammonium diuranate - DUA and uranium tetrafluoride - UF 4 . This work describes a procedure for preparing uranium tetrafluoride by a dry route using as raw material the filtrate generated when producing routinely ammonium uranyl carbonate. The filtrate consists primarily of a solution containing high concentrations of ammonium (NH 4 + ), fluoride (F - ), carbonate (CO 3 -- ) and low concentrations of uranium. The procedure is basically the recovery of NH 4 F and uranium, as UF 4 , through the crystallization of ammonium bifluoride (NH 4 HF 2 ) and, in a later step, the addition of UO 2 , occurring fluoridation and decomposition. The UF 4 obtained is further diluted in the UF 4 produced routinely at IPEN / CNEN-SP by a wet route process. (author)

Water purification in Borexino

Energy Technology Data Exchange (ETDEWEB)

Giammarchi, M. [Infn Milano (Italy); Balata, M.; Ioannucci, L.; Nisi, S. [Laboratori Nazionali del Gran Sasso (Italy); Goretti, A.; Ianni, A. [Princeton University (United States); Miramonti, L. [Dip. di Fisica dell' Università di Milano e Infn (Italy)

2013-08-08

Astroparticle Physics and Underground experiments searching for rare nuclear events, need high purity materials to act as detectors or detector shielding. Water has the advantage of being cheap, dense and easily available. Most of all, water can be purified to the goal of obatining a high level of radiopurity. Water Purification can be achieved by means of a combination of processes, including filtration, reverse osmosis, deionization and gas stripping. The Water Purification System for the Borexino experiment, will be described together with its main performances.

Affinity chromatography: A versatile technique for antibody purification.

Science.gov (United States)

Arora, Sushrut; Saxena, Vikas; Ayyar, B Vijayalakshmi

2017-03-01

Antibodies continue to be extremely utilized entities in myriad applications including basic research, imaging, targeted delivery, chromatography, diagnostics, and therapeutics. At production stage, antibodies are generally present in complex matrices and most of their intended applications necessitate purification. Antibody purification has always been a major bottleneck in downstream processing of antibodies, due to the need of high quality products and associated high costs. Over the years, extensive research has focused on finding better purification methodologies to overcome this holdup. Among a plethora of different techniques, affinity chromatography is one of the most selective, rapid and easy method for antibody purification. This review aims to provide a detailed overview on affinity chromatography and the components involved in purification. An array of support matrices along with various classes of affinity ligands detailing their underlying working principles, together with the advantages and limitations of each system in purifying different types of antibodies, accompanying recent developments and important practical methodological considerations to optimize purification procedure are discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

Radiation-adsorption purification of effluents containing pesticides

International Nuclear Information System (INIS)

Brusentseva, S.A.; Shubin, V.N.; Nikonorova, G.K.; Zorin, D.M.; Sosnovskaya, A.A.; Petryaev, E.P.; Vlasova, V.I.; Edimicheva, I.P.; Subbotina, N.N.; Belorusskij Gosudarstvennyj Univ., Minsk)

1986-01-01

The radiation-adsorption purification is one of the new direction in the radiation purification of natural wastes and effluents containing pesticides. This method combines the conventional adsorption purification with radiation treatment of the sorbent, and the result the protection time of the sorbent increases due to the radiation regeneration of carbon. In present work the method was used for purification of effluents from pesticides, such as 4,4'Dichlorodiphenyltrichloroethane /DDT/, 1,2,3,4,5,6-hexachlorocyclohexane /HCCH/, dimethyl 2,2-dichlorovinylphosphate /DDVF/ and petroleum products (a mixture of kerosene and xylene in ratio 7:1). Such effluents are formed at factories producing an insecticide aerosol 'Prime-71'. Three investigations were carried out on model with a solution similar composition to industrial effluents. (author)

Safety analysis report on the ''Paducah Tiger'' overpack for 10-ton cylinder of uranium hexafluoride

International Nuclear Information System (INIS)

Stitt, D.H.

1978-01-01

A summary of analysis performed to assess the puncture resistance of the Paducah Tiger under a particularly severe (worst case) orientation of the external puncture pin is presented. The six-inch diameter cylindrical puncture pin has been oriented to place its impact location immediately opposite the valve body mounted to the dished head of the uranium hexafluoride cylinder. The valve body is assumed to have a one-inch clearance relative to the inner wall of the overpack. Analysis indicates that significant residual kinetic energy remains in the system at the instant of overpack inner wall contact with the valve body. Thus, there is strong evidence suggesting that the valve body can be damaged, or sheared from the dished head of the UF 6 , under the assumed worst case impact orientation

Hydraulic breakage of tanks for the transport of uranium hexafluoride (UF6)

International Nuclear Information System (INIS)

Biaggio, A.L.; Lee Gonzales, H.M.; Lopez Vietri, J.R.; Novo, R.G.

1987-01-01

To begin with, the tank models that are proposed by the international norms for the transport and storage of hexafluoride of uranium (UF 6 ) are briefly described. The operations related to the transport in its different forms are also described, particularly those that can produce the hydraulic breakage of tanks during its course or in later stages, when incorrectly performed. With reference to those operations, the most important physicochemical properties of UF 6 as for safety are analyzed. A quantitative evaluation of the deviations of parameters that are controlled during the heating of tanks, comparing them with the normative nominal values, is performed. Adopting some simplifying hypothesis, a general study, applicable to all tank models proposed by norms, is carried out to determine the temperature at which the hydraulic breakage takes place when they are heated in closed-valve conditions. A curve is obtained by plotting the hydraulic breakage temperature against the filling degree. To conclude, the values obtained are compared with the results of other theoretical studies on this subject. (Author)

Evaluation of a redesigned 3/4-inch uranium hexafluoride cylinder valve stem

International Nuclear Information System (INIS)

Zonner, L.A.; Wamsley, S.D.

1978-01-01

The performance of a redesigned 3/4-in. uranium hexafluoride cylinder valve stem has been evaluated at the Portsmouth Gaseous Diffusion Plant. Prototypes, machined from Monel bar stock and having a 45 0 tip angle instead of the 15 0 tip angle of the standard valve stem, were fabricated. Tests included: cyclic leak evaluation; flow restriction determination; wear testing with uranyl fluoride deposits in the valve seat; stress corrosion testing; field testing (in previously rejected valve bodies); and production leak testing. Because their overall test performance was excellent, actual production usage of the redesigned stems was initiated. The in-service performance of valves fitted with redesigned stems has been significantly superior to that of valves having the standard stems: rejection rates have been 0.7 and 16.6 percent, respectively. Recommendations are made to replace all 15 0 angle tip stems presently in service with new stems having a 45 0 angle tip and to specify the new stem tip design for future 3/4-in. valve purchases

Standard specification for uranium hexafluoride enriched to less than 5 % 235U

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This specification covers nuclear grade uranium hexafluoride (UF6) that either has been processed through an enrichment plant, or has been produced by the blending of Highly Enriched Uranium with other uranium to obtain uranium of any 235U concentration below 5 % and that is intended for fuel fabrication. The objectives of this specification are twofold: (1) To define the impurity and uranium isotope limits for Enriched Commercial Grade UF6 so that, with respect to fuel design and manufacture, it is essentially equivalent to enriched uranium made from natural UF6; and (2) To define limits for Enriched Reprocessed UF6 to be expected if Reprocessed UF6 is to be enriched without dilution with Commercial Natural UF6. For such UF6, special provisions, not defined herein, may be needed to ensure fuel performance and to protect the work force, process equipment, and the environment. 1.2 This specification is intended to provide the nuclear industry with a standard for enriched UF6 that is to be used in the pro...

A concept of a nonfissile uranium hexafluoride overpack for storage, transport, and processing of corroded cylinders

International Nuclear Information System (INIS)

Pope, R.B.; Cash, J.M.; Singletary, B.H.

1996-01-01

There is a need to develop a means of safely transporting breached 48-in. cylinders containing depleted uranium hexafluoride (UF 6 ) from current storage locations to locations where the contents can be safely removed. There is also a need to provide a method of safely and easily transporting degraded cylinders that no longer meet the US Department of Transportation (DOT) and American National Standards Institute, Inc., (ANSI) requirements for shipments of depleted UF 6 . A study has shown that an overpack can be designed and fabricated to satisfy these needs. The envisioned overpack will handle cylinder models 48G, 48X, and 48Y and will also comply with the ANSI N14.1 and the American Society of Mechanical Engineers (ASME) Sect. 8 requirements

Interim guidance on the safe transport of uranium hexafluoride

International Nuclear Information System (INIS)

1991-06-01

Uranium hexafluoride (UF 6 ) is a radioactive material that has significant non-radiological hazardous properties. In conformity with international regulatory practice for dangerous goods transport, these properties are classed as ''subsidiary risks'', although they predominate in the cases of depleted and natural UF 6 . UF 6 is transported as a solid material below atmospheric pressure. The IAEA Regulations for the Safe Transport of Radioactive Material, 1985 Edition, Safety Series No. 6, make recommendations that aimed to provide an adequate level of safety against radiological and criticality hazards. The basis for these is that the stringency of package performance requirements, operational procedures and approval and administrative procedures is graded relative to the severity of the hazard. The cylinders used for transporting UF 6 are also used in the production, storage and use of the material and that the fraction of their life cycle in which transport is involved is small. Consideration must also be given to the large number of existing cylinders (estimated to be between 60,000 and 70,000). Specific recommendations provided for UF 6 transport, listed in Section II, are additional to the requirements of the Regulations. The intent of these additional recommendations is to restrict contamination and to provide protection to workers and to the general public against the chemical hazard possibly resulting from a severe accident involving the transport of UF 6 , and in addition against the consequences of explosive rupture of small bare cylinders of UF 6 . 20 refs, figs and tabs

A sulfur hexafluoride sensor using quantum cascade and CO2 laser-based photoacoustic spectroscopy.

Science.gov (United States)

Rocha, Mila; Sthel, Marcelo; Lima, Guilherme; da Silva, Marcelo; Schramm, Delson; Miklós, András; Vargas, Helion

2010-01-01

The increase in greenhouse gas emissions is a serious environmental problem and has stimulated the scientific community to pay attention to the need for detection and monitoring of gases released into the atmosphere. In this regard, the development of sensitive and selective gas sensors has been the subject of several research programs. An important greenhouse gas is sulphur hexafluoride, an almost non-reactive gas widely employed in industrial processes worldwide. Indeed it is estimated that it has a radiative forcing of 0.52 W/m(2). This work compares two photoacoustic spectrometers, one coupled to a CO(2) laser and another one coupled to a Quantum Cascade (QC) laser, for the detection of SF(6). The laser photoacoustic spectrometers described in this work have been developed for gas detection at small concentrations. Detection limits of 20 ppbv for CO(2) laser and 50 ppbv for quantum cascade laser were obtained.

21 CFR 876.5665 - Water purification system for hemodialysis.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Water purification system for hemodialysis. 876... SERVICES (CONTINUED) MEDICAL DEVICES GASTROENTEROLOGY-UROLOGY DEVICES Therapeutic Devices § 876.5665 Water purification system for hemodialysis. (a) Identification. A water purification system for hemodialysis is a...

Sodium purification in Rapsodie; La purification du sodium a Rapsodie

Energy Technology Data Exchange (ETDEWEB)

Giraud, B [Commissariat a l' Energie Atomique, Dir. des Piles Atomiques, Cadarache (France). Centre d' Etudes Nucleaires

1968-07-01

This report is one of a series of publications presenting the main results of tests carried out during the start-up of the first french fast neutron reactor: Rapsodie. The article presents the sodium purification techniques used in the reactor cooling circuits both from the constructional point of view and with respect to results obtained during the first years working. (author) [French] Ce rapport fait partie d'une serie de publications presentant l'essentiel des resultats des essais effectues a l'occasion du demarrage du premier reacteur francais a neutrons rapides: RAPSODIE. Cet article expose les techniques de la purification du sodium utilise dans les circuits de refroidissement du reacteur tant au point de vue de leur realisation technologique, que des resultats obtenus pendant la premiere annee de fonctionnement. (auteur)

Purification of functionalized DNA origami nanostructures.

Science.gov (United States)

Shaw, Alan; Benson, Erik; Högberg, Björn

2015-05-26

The high programmability of DNA origami has provided tools for precise manipulation of matter at the nanoscale. This manipulation of matter opens up the possibility to arrange functional elements for a diverse range of applications that utilize the nanometer precision provided by these structures. However, the realization of functionalized DNA origami still suffers from imperfect production methods, in particular in the purification step, where excess material is separated from the desired functionalized DNA origami. In this article we demonstrate and optimize two purification methods that have not previously been applied to DNA origami. In addition, we provide a systematic study comparing the purification efficacy of these and five other commonly used purification methods. Three types of functionalized DNA origami were used as model systems in this study. DNA origami was patterned with either small molecules, antibodies, or larger proteins. With the results of our work we aim to provide a guideline in quality fabrication of various types of functionalized DNA origami and to provide a route for scalable production of these promising tools.

Biodiesel separation and purification: A review

International Nuclear Information System (INIS)

Atadashi, I.M.; Aroua, M.K.; Aziz, A. Abdul

2011-01-01

Biodiesel as a biodegradable, sustainable and clean energy has worldwide attracted renewed and growing interest in topical years, chiefly due to development in biodiesel fuel and ecological pressures which include climatic changes. In the production of biodiesel from biomass, separation and purification of biodiesel is a critical technology. Conventional technologies used for biodiesel separation such as gravitational settling, decantation, filtration and biodiesel purification such as water washing, acid washing, and washing with ether and absorbents have proven to be inefficient, time and energy consumptive, and less cost effective. The involvement of membrane reactor and separative membrane shows great promise for the separation and purification of biodiesel. Membrane technology needs to be explored and exploited to overcome the difficulties usually encountered in the separation and purification of biodiesel. In this paper both conventional and most recent membrane technologies used in refining biodiesel have been critically reviewed. The effects of catalysts, free fatty acids, water content and oil to methanol ratios on the purity and quality of biodiesel are also examined. (author)

Uranium hexafluoride: A manual of good handling practices

International Nuclear Information System (INIS)

1991-10-01

For many years, the US Department of Energy (DOE) and its predecessor agencies have shared with the nuclear industry their experience in the area of uranium hexafluoride (UF 6 ) shipping containers and handling procedures. The information contained in this manual updates information contained in earlier issues. It covers the essential aspects of UF 6 handling, cylinder filling and emptying, general principles of weighing and sampling, shipping, and the use of protective overpacks. The physical and chemical properties of UF 6 are also described and tabulated. The nuclear industry is responsible for furnishing its own shipping cylinders and suitable protective overpacks. A substantial effort has been made by the industry to standardize UF 6 cylinders, samples, and overpacks. The quality of feed materials is important to the safe and efficient operation of the enriching facilities, and the UF 6 product purity from the enriching facilities is equally important to the fuel fabricator, the utilities, the operators of research reactors, and other users. The requirements have been the impetus for an aggressive effort by DOE and its contractors to develop accurate techniques for sampling and for chemical and isotopic analysis. A quality control program is maintained within the DOE enriching facilities to ensure that the proper degree of accuracy and precision are obtained for all the required measurements. The procedures and systems described for safe handling of UF 6 presented in this document have been developed and evaluated in DOE facilities during more than 40 years of handling vast quantities of UF 6 . With proper consideration for its nuclear properties, UF 6 may be safely handled in essentially the same manner as any other corrosive and/or toxic chemical

Review of experience gained in fabricating nuclear grade uranium and thorium compounds and their analytical quality control at the Instituto de Energia Atomica, Sao Paulo, Brazil

International Nuclear Information System (INIS)

Abrao, A.; Franca Junior, J.M.; Ikuta, A.

1977-01-01

The main activities developed at 'Instituto de Energia Atomica' Sao Paulo, Brazil, on the recovery of uranium from ores, the purification of uranium and thorium raw concentrates and their transformation in nuclear grade compounds, are reviewed. The design and assemble of pilot facilities for ammonium diuranate (ADV) uranium tetrafluoride, uranium trioxide, uranium oxide microspheres, uranyl nitrate denitration, uranim hexafluoride and thorium compounds are discussed. The establishment of analytical procedures are emphasized [pt

Purification of crude biodiesel using dry washing and membrane technologies

OpenAIRE

Atadashi, I.M.

2015-01-01

Purification of crude biodiesel is mandatory for the fuel to meet the strict international standard specifications for biodiesel. Therefore, this paper carefully analyzed recently published literatures which deal with the purification of biodiesel. As such, dry washing technologies and the most recent membrane biodiesel purification process have been thoroughly examined. Although purification of biodiesel using dry washing process involving magnesol and ion exchange resins provides high-quali...

Antimicrobial Peptide Production and Purification.

Science.gov (United States)

Suda, Srinivas; Field, Des; Barron, Niall

2017-01-01

Antimicrobial peptides (AMPs) are natural defense compounds which are synthesized as ribosomal gene-encoded pre-peptides and produced by all living organisms. AMPs are small peptides, usually cationic and typically have hydrophobic residues which interact with cell membranes and have either a narrow or broad spectrum of biological activity. AMPs are isolated from the natural host or heterologously expressed in other hosts such as Escherichia coli. The proto-typical lantibiotic Nisin is a widely used AMP that is produced by the food-grade organism Lactococcus lactis. Although AMP production and purification procedures require optimization for individual AMPs, the Nisin production and purification protocol outlined in this chapter can be easily applied with minor modifications for the production and purification of other lantibiotics or AMPs. While Nisin is produced and secreted into the supernatant, steps to recover Nisin from both cell-free supernatant and cell pellet are outlined in detail.

Use of sulfur hexafluoride and perfluorocarbon tracers in plutonium storage containers for leak detection

International Nuclear Information System (INIS)

Kung, J.K.

1998-05-01

This study involves an investigation of the feasibility of a tracer-based leak detection system for long-term interim plutonium storage. In particular, a protocol has been developed based on the use of inert tracers with varying concentrations in order to open-quotes fingerprintclose quotes or open-quotes tagclose quotes specific containers. A particular combination of tracers at specific ratios could be injected into the free volume of each container, allowing for the detection of leaks as well as determination of the location of leaking containers. Based on plutonium storage considerations, sulfur hexafluoride and four perfluorocarbon tracers were selected and should allow a wide range of viable fingerprinting combinations. A open-quotes high-lowclose quotes protocol which uses two distinct chromatographic peak areas or concentration levels, is recommended. Combinations of air exchange rates, detection durations, and detectability limits are examined in order to predict minimum tracer concentrations required for injection in storage containers

Design and construction of a Type B overpack container for the safe transportation of enriched uranium hexafluoride

International Nuclear Information System (INIS)

Gablin, K.A.

1976-01-01

The Paducah Tiger is an overpack designed for the international shipment of ten-ton cylinders of uranium hexafluoride in enriched form above the level of low specific acitivity. This container is designed as a Type B Package and has undergone all the tests and analyses required for a U.S. Department of Transportation Permit No. 6553. The Paducah Tiger is currently being used to ship fuel material in the USA on both truck and rail modes of transportation. In many ways, the design resembles the Super Tigersup(R), but incorporates features such as ISO corners, quick opening fasteners, and interior shock isolators that provide a system approach to the high volume of fuel shipment required in the last half of the 20th century. (author)

RELIGION AND PURIFICATION OF SOUL

Directory of Open Access Journals (Sweden)

Azam Khodashenas Pelko

2010-11-01

Full Text Available The Jainism emphasizes three major teachings about the purification of the soul (jiva, Ahimsa, Aparigrapha and anekantwad. Jainism, The focus of this religion has been purification of the soul by means of right conduct, right faith and right knowledge. The ultimate goal of Hinduism is Moksha or liberation (total freedom. In Hinduism, purification of the soul is a goal that one must work to attain. The Buddhism is the science of pursuing the aim of making the human mind perfect, and of purifying the human soul. The knowledge of purifying of the soul and softening of the hearts is as essential for human. They having the correct motivations means purifying our souls from hypocrisy, caprice, and heedlessness. The primary goal of Taoism may be described as the mystical intuition of the Tao, which is the way, the undivided unity, and the ultimate Reality. According to the Christianity access to truth cannot be conceived without purity of the soul

Solvent-extraction purification of neptunium

International Nuclear Information System (INIS)

Kyser, E.A.; Hudlow, S.L.

2008-01-01

The Savannah River Site (SRS) has recovered 237 Np from reactor fuel that is currently being processed into NpO 2 for future production of 238 Pu. Several purification flowsheets have been utilized. An oxidizing solvent-extraction (SX) flowsheet was used to remove Fe, sulfate ion, and Th while simultaneously 237 Np, 238 Pu, u, and nonradioactive Ce(IV) was extracted into the tributyl phosphate (TBP) based organic solvent. A reducing SX flowsheet (second pass) removed the Ce and Pu and recovered both Np and U. The oxidizing flowsheet was necessary for solutions that contained excessive amounts of sulfate ion. Anion exchange was used to perform final purification of Np from Pu, U, and various non-actinide impurities. The Np(IV) in the purified solution was then oxalate-precipitated and calcined to an oxide for shipment to other facilities for storage and future target fabrication. Performance details of the SX purification and process difficulties are discussed. (authors)

Single-step affinity purification for fungal proteomics.

Science.gov (United States)

Liu, Hui-Lin; Osmani, Aysha H; Ukil, Leena; Son, Sunghun; Markossian, Sarine; Shen, Kuo-Fang; Govindaraghavan, Meera; Varadaraj, Archana; Hashmi, Shahr B; De Souza, Colin P; Osmani, Stephen A

2010-05-01

A single-step protein affinity purification protocol using Aspergillus nidulans is described. Detailed protocols for cell breakage, affinity purification, and depending on the application, methods for protein release from affinity beads are provided. Examples defining the utility of the approaches, which should be widely applicable, are included.

Efficient removal of sulfur hexafluoride (SF6) through reacting with recycled electroplating sludge.

Science.gov (United States)

Zhang, Jia; Zhou, Ji Zhi; Liu, Qiang; Qian, Guangren; Xu, Zhi Ping

2013-06-18

This paper reports that recycled electroplating sludge is able to efficiently remove greenhouse gas sulfur hexafluoride (SF6). The removal process involves various reactions of SF6 with the recycled sludge. Remarkably, the sludge completely removed SF6 at a capacity of 1.10 mmol/g (SF6/sludge) at 600 °C. More importantly, the evolved gases were SO2, SiF4, and a limited amount of HF, with no toxic SOF4, SO2F2, or SF4 being detected. These generated gases can be readily captured and removed by NaOH solution. The reacted solids were further found to be various metal fluorides, thus revealing that SF6 removal takes place by reacting with various metal oxides and silicate in the sludge. Moreover, the kinetic investigation revealed that the SF6 reaction with the sludge is a first-order chemically controlled process. This research thus demonstrates that the waste electroplating sludge can be potentially used as an effective removal agent for one of the notorious greenhouse gases, SF6.

Dry uranium tetrafluoride process preparation using the uranium hexafluoride reconversion process effluents

International Nuclear Information System (INIS)

Silva Neto, Joao Batista da

2008-01-01

It is a well known fact that the use of uranium tetrafluoride allows flexibility in the production of uranium suicide and uranium oxide fuel. To its obtention there are two conventional routes, the one which reduces uranium from the UF 6 hydrolysis solution with stannous chloride, and the hydro fluorination of a solid uranium dioxide. In this work we are introducing a third and a dry way route, mainly utilized to the recovery of uranium from the liquid effluents generated in the uranium hexafluoride reconversion process, at IPEN/CNEN-SP. Working in the liquid phase, this route comprises the recuperation of ammonium fluoride by NH 4 HF 2 precipitation. Working with the solid residues, the crystallized bifluoride is added to the solid UO 2 , which comes from the U mini plates recovery, also to its conversion in a solid state reaction, to obtain UF 4 . That returns to the process of metallic uranium production unity to the U 3 Si 2 obtention. This fuel is considered in IPEN CNEN/SP as the high density fuel phase for IEA-R1m reactor, which will replace the former low density U 3 Si 2 -Al fuel. (author)

New approach for safeguarding enriched uranium hexafluoride bulk transfers

International Nuclear Information System (INIS)

Doeher, L.W.; Pontius, P.E.; Whetstone, J.R.

1978-01-01

The unique concepts of American National Standard ANSI N15.18-1975 ''Mass Calibration Techniques for Nuclear Material Control'' are discussed in regard to the establishment and maintenance of control of mass measurement of Uranium Hexafluoride (UF 6 ) both within and between facilities. Emphasis is placed on the role of control of the measurements between facilities, and thus establish decision points for detection of measurement problems and making safeguards judgments. The unique concepts include the use of artifacts of UF 6 packaging cylinders, calibrated by a central authority, to introduce the mass unit into all of the industries' weighing processes. These are called Replicate Mass Standards (RMS). This feat is accomplished by comparing the RMS to each facility's In-House Standards (IHS), also artifacts, and thence the usage of these IHS to quantify the systematic and random errors of each UF 6 mass measurement process. A recent demonstration, which exchanged UF 6 cylinders between two facilities, who used ANSI N15.18-1975 concepts and procedures is discussed. The discussion includes methodology and treatment of data for use in detection of measurement and safeguards problems. The discussion incorporates the methodology for data treatment and judgments concerning (1) the common base, (2) measurement process off-sets, (3) measurement process precision, and (4) shipper-receiver bulk measurement differences. From the evidence gained in the demonstration, conclusions are reached as to the usefulness of the realistic criteria for detection of mass measurement problems upon acceptance of the concepts of ANSI N15.18-1975

Purification of rhamnolipid using colloidal magnetic nanoparticles ...

African Journals Online (AJOL)

Phospholipid-coated colloidal magnetic nanoparticles with mean magnetite core size of 9 nm are shown to be effective ion exchange media for the recovery and purification of Rhaminolipid from culture mixtures. These particles have high adsorption capacity for purification (an order of magnitude larger than the best ...

Effect of water purification process in radioactive content: analysis on small scale purification plants

International Nuclear Information System (INIS)

Lopez del Rio, H.; Quiroga S, J. C.; Davila R, J. I.; Mireles G, F.

2009-10-01

Water from small scale purification plants is a low cost alternative for consumers in comparison to the bottled commercial presentations. Because of its low cost per liter, the consumption of this product has increased in recent years, stimulating in turn the installation of purification systems for these small businesses. The purpose of this study was to estimate the efficiency of small scale purification systems located in the cities of Zacatecas and Guadalupe, Zacatecas, to reduce the radioactive content of water. It was measured the total alpha and beta activity in water samples of entry and exit to process, through the liquid scintillation technique. In general it was observed that the process is more efficient in removing alpha that beta activity. The fraction of total alpha activity removed varied between 27 and 100%, while between 0 and 77% of the total beta activity was removed by the analyzed plants. In all cases, the total radioactivity level was lower than the maximum permissible value settled by the official mexican standard for drinking water. (Author)

Purification of crude biodiesel using dry washing and membrane technologies

Directory of Open Access Journals (Sweden)

I.M. Atadashi

2015-12-01

Full Text Available Purification of crude biodiesel is mandatory for the fuel to meet the strict international standard specifications for biodiesel. Therefore, this paper carefully analyzed recently published literatures which deal with the purification of biodiesel. As such, dry washing technologies and the most recent membrane biodiesel purification process have been thoroughly examined. Although purification of biodiesel using dry washing process involving magnesol and ion exchange resins provides high-quality biodiesel fuel, considerable amount of spent absorbents is recorded, besides the skeletal knowledge on its operating process. Further, recent findings have shown that biodiesel purification using membrane technique could offer high-quality biodiesel fuel with less wastewater discharges. Thus, both researchers and industries are expected to benefit from the development of membrane technique in purifying crude biodiesel. As well biodiesel purification via membranes has been shown to be environmentally friendly. For these reasons, it is important to explore and exploit membrane technology to purify crude biodiesel.

Materials for Molybdenum 99 purification

International Nuclear Information System (INIS)

Wilkinson, M. Victoria; Mondino, Angel V.; Manzini, Alberto C.

2003-01-01

The National Atomic Energy Commission (CNEA) produces fission Mo 99, an isotope of wide use in nuclear medicine. In order to simplify the current Mo 99 production process, to shorten its duration and reduce impurities in the final product, alternative methods for purification steps were looked for. In this work a variety of new materials for the purification columns were designed, all of them with carbon. These materials were studied and a material which contribute with the best results for molybdenum retention, was selected. The preparation procedure and the working conditions were determined. (author)

Electron beam silicon purification

Energy Technology Data Exchange (ETDEWEB)

Kravtsov, Anatoly [SIA ' ' KEPP EU' ' , Riga (Latvia); Kravtsov, Alexey [' ' KEPP-service' ' Ltd., Moscow (Russian Federation)

2014-11-15

Purification of heavily doped electronic grade silicon by evaporation of N-type impurities with electron beam heating was investigated in process with a batch weight up to 50 kilos. Effective temperature of the melt, an indicative parameter suitable for purification process characterization was calculated and appeared to be stable for different load weight processes. Purified material was successfully approbated in standard CZ processes of three different companies. Each company used its standard process and obtained CZ monocrystals applicable for photovoltaic application. These facts enable process to be successfully scaled up to commercial volumes (150-300 kg) and yield solar grade silicon. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Biological assessment of the effects of construction and operation of a depleted uranium hexafluoride conversion facility at the Paducah, Kentucky, site.

Energy Technology Data Exchange (ETDEWEB)

Van Lonkhuyzen, R.

2005-09-09

The U.S. Department of Energy (DOE) Depleted Uranium Hexafluoride (DUF{sub 6}) Management Program evaluated alternatives for managing its inventory of DUF{sub 6} and issued the ''Programmatic Environmental Impact Statement for Alternative Strategies for the Long-Term Management and Use of Depleted Uranium Hexafluoride'' (DUF{sub 6} PEIS) in April 1999 (DOE 1999). The DUF{sub 6} inventory is stored in cylinders at three DOE sites: Paducah, Kentucky; Portsmouth, Ohio; and East Tennessee Technology Park (ETTP), near Oak Ridge, Tennessee. In the Record of Decision for the DUF{sub 6} PEIS, DOE stated its decision to promptly convert the DUF6 inventory to a more stable chemical form. Subsequently, the U.S. Congress passed, and the President signed, the ''2002 Supplemental Appropriations Act for Further Recovery from and Response to Terrorist Attacks on the United States'' (Public Law No. 107-206). This law stipulated in part that, within 30 days of enactment, DOE must award a contract for the design, construction, and operation of a DUF{sub 6} conversion plant at the Department's Paducah, Kentucky, and Portsmouth, Ohio, sites, and for the shipment of DUF{sub 6} cylinders stored at ETTP to the Portsmouth site for conversion. This biological assessment (BA) has been prepared by DOE, pursuant to the National Environmental Policy Act of 1969 (NEPA) and the Endangered Species Act of 1974, to evaluate potential impacts to federally listed species from the construction and operation of a conversion facility at the DOE Paducah site.

X-ray fluorescence with synchrotron radiation to elemental analysis of lead and calcium content of primary teeth

International Nuclear Information System (INIS)

Souza Guerra, Carolina de; Fernanda Gerlach, Raquel; Graciele Villela Pinto, Nivia; Coutinho Cardoso, Simone; Moreira, Silvana; Pereira de Almeida, Andre; Teixeira Alves Peixoto, Iza; Henrique Meloni, Carlos; Lemos Mota, Carla; Fernando de Oliveira, Luis; Braz, Delson; Cely Barroso, Regina

2010-01-01

Primary teeth were analyzed by micro-SRXRF. The aim of this study was to determine the elemental distribution of lead and calcium in different regions of primary incisor of children living in a notoriously contaminated area (Santo Amaro da Purificacao, Bahia State, Brazil). The measurements were performed in standard geometry of 45 deg. incidence, exciting with a white beam and using a conventional system collimation (orthogonal slits) in the XRF beamline at the Synchrotron Light National Laboratory (Campinas, Brazil).

Purification of a-galactosidase from seeds of Sesbania marginata

Directory of Open Access Journals (Sweden)

Falco A.L.P.

2000-01-01

Full Text Available Alpha-galactosidase taken from a raw extract of Sesbania marginata legume seeds was purified by partitioning in aqueous two-phase systems (ATPS. Initially, galactomannan/dextran 2,000,000 systems were used for the purification, and the partition coefficients of alpha -galactosidase varied from 1.5 to 4.0. However, mass transport in these systems was poor due to the high viscosity of the employed polymers. Therefore, partitioning in polyethyleneglycol (PEG/ sodium phosphate systems and the effect of sodium chloride upon the enzyme purification and the yield of alpha -galactosidase were also investigated. The purification achieved in a single-step was 5.7 with a recovery of 144% of alpha -galactosidase, possibly due to the removal of materials which inhibited alpha -galactosidase activity before the purification. The removal of the main protein contaminants and the highest yields were achieved in PEG 4,000/ sodium phosphate + 6% NaCl system at pH 5.0. Further purification by preparative on-exchange chromatography was also developed.

Necessity of purification during bacterial DNA extraction with environmental soils

Directory of Open Access Journals (Sweden)

Hyun Jeong Lim

2017-08-01

Full Text Available Complexity and heterogeneity of soil samples have often implied the inclusion of purification steps in conventional DNA extraction for polymerase chain reaction (PCR assays. Unfortunately the purification steps are also time and labor intensive. Therefore the necessity of DNA purification was re-visited and investigated for a variety of environmental soil samples that contained various amounts of PCR inhibitors. Bead beating and centrifugation was used as the baseline (without purification method for DNA extraction. Its performance was compared with that of conventional DNA extraction kit (with purification. The necessity criteria for DNA purification were established with environmental soil samples. Using lysis conditions at 3000 rpm for 3 minutes with 0.1 mm glass beads, centrifugation time of 10 minutes and 1:10 dilution ratio, the baseline method outperformed conventional DNA extraction on cell seeded sand samples. Further investigation with PCR inhibitors (i.e., humic acids, clay, and magnesium [Mg] showed that sand samples containing less than 10 μg/g humic acids and 70% clay may not require purifications. Interestingly, the inhibition pattern of Mg ion was different from other inhibitors due to the complexation interaction of Mg ion with DNA fragments. It was concluded that DNA extraction method without purification is suitable for soil samples that have less than 10 μg/g of humic acids, less than 70% clay content and less than 0.01% Mg ion content.

Evaluation of strategies to control Fab light chain dimer during mammalian expression and purification: A universal one-step process for purification of correctly assembled Fab.

Science.gov (United States)

Spooner, Jennifer; Keen, Jenny; Nayyar, Kalpana; Birkett, Neil; Bond, Nicholas; Bannister, David; Tigue, Natalie; Higazi, Daniel; Kemp, Benjamin; Vaughan, Tristan; Kippen, Alistair; Buchanan, Andrew

2015-07-01

Fabs are an important class of antibody fragment as both research reagents and therapeutic agents. There are a plethora of methods described for their recombinant expression and purification. However, these do not address the issue of excessive light chain production that forms light chain dimers nor do they describe a universal purification strategy. Light chain dimer impurities and the absence of a universal Fab purification strategy present persistent challenges for biotechnology applications using Fabs, particularly around the need for bespoke purification strategies. This study describes methods to address light chain dimer formation during Fab expression and identifies a novel CH 1 affinity resin as a simple and efficient one-step purification for correctly assembled Fab. © 2015 Wiley Periodicals, Inc.

Technological assumptions for biogas purification.

Science.gov (United States)

Makareviciene, Violeta; Sendzikiene, Egle

2015-01-01

Biogas can be used in the engines of transport vehicles and blended into natural gas networks, but it also requires the removal of carbon dioxide, hydrogen sulphide, and moisture. Biogas purification process flow diagrams have been developed for a process enabling the use of a dolomite suspension, as well as for solutions obtained by the filtration of the suspension, to obtain biogas free of hydrogen sulphide and with a carbon dioxide content that does not exceed 2%. The cost of biogas purification was evaluated on the basis of data on biogas production capacity and biogas production cost obtained from local water treatment facilities. It has been found that, with the use of dolomite suspension, the cost of biogas purification is approximately six times lower than that in the case of using a chemical sorbent such as monoethanolamine. The results showed travelling costs using biogas purified by dolomite suspension are nearly 1.5 time lower than travelling costs using gasoline and slightly lower than travelling costs using mineral diesel fuel.

Extraction and purification of plutonium by a tertiary amine; Extraction et purification du plutonium par une amine tertiaire

Energy Technology Data Exchange (ETDEWEB)

Trentinian, M de; Chesne, A [Commissariat a l' Energie Atomique, Fontenay aux Roses, Section de Chimie des Actimides (France).Centre d' Etudes Nucleaires; Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

Trilaurylamine diluted with a paraffinic solvent (dodecane) was studied as part of the research dealing with the separation and purification of plutonium. The physical properties (solubility of nitrates in the amine as a function of temperature) and the resistance to radiations of this substance were examined. The extraction characteristics of nitric solutions of plutonium, uranium and certain fission products are given as a function of the following factors: concentration of the various ions in solution, valency states. A method of plutonium purification based on these results is presented. (author) [French] La trilaurylamine diluee par un solvant paraffinique (dodecane) a ete etudiee dans le cadre des recherches concernant la separation et la purification du plutonium. Une etude des caracteres physiques (solubilite des nitrates dans l'amine en fonction de la temperature) s'ajoute a celle de la tenue aux radiations de ce corps. Les caracteristiques d'extraction de solutions nitriques de plutonium, uranium, et certains produits de fission, sont donnes en fonction des facteurs suivants: concentration des differents ions en solution, etats de valence. On presente une methode de purification du plutonium basee sur ces resultats. (auteur)

Optimization of laboratory scale production and purification of ...

African Journals Online (AJOL)

Microcystin content is however highly variable and optimised culture conditions are essential to produce viable yields of microcystin for purification. We describe the optimization of culture conditions and evaluation of various purification methods to enhance the yield of microcystin from laboratory scale culture.

Hydrogen purification by periodic adsorption

Energy Technology Data Exchange (ETDEWEB)

Barg, Christian; Secchi, Argimiro R.; Trierweiler, Jorge O. [Rio Grande do Sul Univ., Porto Alegre, RS (Brazil). Dept. de Engenharia Quimica]. E-mail: cbarg@enq.ufrgs.br; arge@enq.ufrgs.br; jorge@enq.ufrgs.br

2000-07-01

The periodic adsorption processes have been widely used for industrial applications, mainly because it spends less energy than the usual gas separation processes, like the cryogenic distillation. The largest commercial application of periodic adsorption processes is the pressure swing adsorption (PSA) applied to hydrogen purification. Although its wide use in the chemical and petrochemical industry, there are no reports in the open literature about complete modeling studies of a complex commercial unit, with multiple adsorbents and multiple beds and several feed components. This study has as objective the modeling, optimization and dynamical analysis of an industrial PSA unit for hydrogen purification. (author)

Extraction and purification of yellow cake

International Nuclear Information System (INIS)

Yousif, E.H.

2006-01-01

This dissertation has reviewed current studies on production and purification of yellow cake from uranium ores by both acid and alkaline leaching processes. It comprises three chapters, the first one deal with uranium minerals, uranium deposits, geology of uranium and uranium isotopes. The second chapter covers mining and milling methods, uranium leaching chemistry, precipitation, and purification of uranium concentrate by solvent extraction and possible impurities that commonly interfered with yellow cake. The last chapter presented ongoing literature review.(Author)

Microbiological and technical aspects of anaerobic waste water purification

International Nuclear Information System (INIS)

Aivasidis, A.

1994-01-01

Anaerobic waste water purification is likely to be another example of how innovations can result from the joint use of biological and technical concepts. No matter how far the optimization of oxygen input with aerobic waste water purification advances it will still be the less a real competitor for anaerobic techniques the more polluted the waste water is. The principle of carrier fixation to avoid their washing out, too, has often been observed in nature with sessile microorganisms. With highly polluted water, anaerobic purification does not only work at no expenditure of energy but it can also make excess energy available for use in other processes. Another important argument for anaerobic methods of waste water purification is probably the clearly reduced production of excess sludge. (orig.) [de

Multipartite electronic entanglement purification with charge detection

Energy Technology Data Exchange (ETDEWEB)

Sheng Yubo [Department of Physics, Tsinghua University, Beijing 100084 (China); Deng, Fu-Guo [Department of Physics, Beijing Normal University, Beijing 100875 (China); Long Guilu, E-mail: gllong@tsinghua.edu.c [Department of Physics, Tsinghua University, Beijing 100084 (China); Key Laboratory for Atomic and Molecular NanoSciences, Tsinghua University, Beijing 100084 (China); Tsinghua National Laboratory for Information Science and Technology, Beijing 100084 (China)

2011-01-17

We present a multipartite entanglement purification scheme in a Greenberger-Horne-Zeilinger state for electrons based on their spins and their charges. This scheme works for purification with two steps, i.e., bit-flip error correction and phase-flip error correction. By repeating these two steps, the parties in quantum communication can get some high-fidelity multipartite entangled electronic systems.

21 CFR 884.6170 - Assisted reproduction water and water purification systems.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Assisted reproduction water and water purification... Devices § 884.6170 Assisted reproduction water and water purification systems. (a) Identification. Assisted reproduction water purification systems are devices specifically intended to generate high quality...

Some Investigations of the Reaction of Activated Charcoal with Fluorine and Uranium Hexafluoride

Energy Technology Data Exchange (ETDEWEB)

Del Cul, G.D.; Fiedor, J.N.; Simmons, D.W.; Toth, L.M.; Trowbridge, L.D.; Williams

1998-09-01

The Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory has been shut down since 1969, when the fuel salt was drained from the core into two Hastelloy N drain tanks at the reactor site. Over time, fluorine (F{sub 2}) and uranium hexafluoride (UF{sub 6}) moved from the salt through the gas piping to a charcoal bed, where they reacted with the activated charcoal. Some of the immediate concerns related to the migration of F{sub 2} and UF{sub 6} to the charcoal bed were the possibility of explosive reactions between the charcoal and F{sub 2}, the existence of conditions that could induce a criticality accident, and the removal and recovery of the fissile uranium from the charcoal. This report addresses the reactions and reactivity of species produced by the reaction of fluorine and activated charcoal and between charcoal and F{sub 2}-UF{sub 6} gas mixtures in order to support remediation of the MSRE auxiliary charcoal bed (ACB) and the recovery of the fissile uranium. The chemical identity, stoichiometry, thermochemistry, and potential for explosive decomposition of the primary reaction product, fluorinated charcoal, was determined.

Some Investigations of the Reaction of Activated Charcoal with Fluorine and Uranium Hexafluoride

International Nuclear Information System (INIS)

Del Cul, G.D.; Fiedor, J.N.; Simmons, D.W.; Toth, L.M.; Trowbridge, L.D.; Williams

1998-01-01

The Molten Salt Reactor Experiment (MSRE) at Oak Ridge National Laboratory has been shut down since 1969, when the fuel salt was drained from the core into two Hastelloy N drain tanks at the reactor site. Over time, fluorine (F 2 ) and uranium hexafluoride (UF 6 ) moved from the salt through the gas piping to a charcoal bed, where they reacted with the activated charcoal. Some of the immediate concerns related to the migration of F 2 and UF 6 to the charcoal bed were the possibility of explosive reactions between the charcoal and F 2 , the existence of conditions that could induce a criticality accident, and the removal and recovery of the fissile uranium from the charcoal. This report addresses the reactions and reactivity of species produced by the reaction of fluorine and activated charcoal and between charcoal and F 2 -UF 6 gas mixtures in order to support remediation of the MSRE auxiliary charcoal bed (ACB) and the recovery of the fissile uranium. The chemical identity, stoichiometry, thermochemistry, and potential for explosive decomposition of the primary reaction product, fluorinated charcoal, was determined

Superparamagnetic poly(methyl methacrylate) beads for nattokinase purification from fermentation broth.

Science.gov (United States)

Yang, Chengli; Xing, Jianmin; Guan, Yueping; Liu, Huizhou

2006-09-01

An effective method for purification of nattokinase from fermentation broth using magnetic poly(methyl methacrylate) (PMMA) beads immobilized with p-aminobenzamidine was proposed in this study. Firstly, magnetic PMMA beads with a narrow size distribution were prepared by spraying suspension polymerization. Then, they were highly functionalized via transesterification reaction with polyethylene glycol. The surface hydroxyl-modified magnetic beads obtained were further modified with chloroethylamine to transfer the surface amino-modified magnetic functional beads. The morphology and surface functionality of the magnetic beads were examined by scanning electron microscopy and Fourier transform infrared. An affinity ligand, p-aminobenzamidine was covalently immobilized to the amino-modified magnetic beads by the glutaraldehyde method for nattokinase purification directly from the fermentation broth. The purification factor and the recovery of the enzyme activity were found to be 8.7 and 85%, respectively. The purification of nattokinase from fermentation broth by magnetic beads only took 40 min, which shows a very fast purification of nattokinase compared to traditional purification methods.

New Combined Electron-Beam Methods of Wastewater Purification

International Nuclear Information System (INIS)

Pikaev, A.K.; Makarov, I.E.; Ponomarev, A.V.; Kartasheva, L.I.; Podzorova, E.A.; Chulkov, V.N.; Han, B.; Kim, D.K.

1999-01-01

The paper is a brief review of the results obtained with the participation of the authors from the study on combined electron-beam methods for purification of some wastewaters. The data on purification of wastewaters containing dyes or hydrogen peroxide and municipal wastewater in the aerosol flow are considered

TRIMOLECULAR REACTIONS OF URANIUM HEXAFLUORIDE WITH WATER

Energy Technology Data Exchange (ETDEWEB)

Westbrook, M.; Becnel, J.; Garrison, S.

2010-02-25

The hydrolysis reaction of uranium hexafluoride (UF{sub 6}) is a key step in the synthesis of uranium dioxide (UO{sub 2}) powder for nuclear fuels. Mechanisms for the hydrolysis reactions are studied here with density functional theory and the Stuttgart small-core scalar relativistic pseudopotential and associated basis set for uranium. The reaction of a single UF{sub 6} molecule with a water molecule in the gas phase has been previously predicted to proceed over a relatively sizeable barrier of 78.2 kJ {center_dot} mol{sup -1}, indicating this reaction is only feasible at elevated temperatures. Given the observed formation of a second morphology for the UO{sub 2} product coupled with the observations of rapid, spontaneous hydrolysis at ambient conditions, an alternate reaction pathway must exist. In the present work, two trimolecular hydrolysis mechanisms are studied with density functional theory: (1) the reaction between two UF{sub 6} molecules and one water molecule, and (2) the reaction of two water molecules with a single UF{sub 6} molecule. The predicted reaction of two UF{sub 6} molecules with one water molecule displays an interesting 'fluorine-shuttle' mechanism, a significant energy barrier of 69.0 kJ {center_dot} mol{sup -1} to the formation of UF{sub 5}OH, and an enthalpy of reaction ({Delta}H{sub 298}) of +17.9 kJ {center_dot} mol{sup -1}. The reaction of a single UF{sub 6} molecule with two water molecules displays a 'proton-shuttle' mechanism, and is more favorable, having a slightly lower computed energy barrier of 58.9 kJ {center_dot} mol{sup -1} and an exothermic enthalpy of reaction ({Delta}H{sub 298}) of -13.9 kJ {center_dot} mol{sup -1}. The exothermic nature of the overall UF{sub 6} + 2 {center_dot} H{sub 2}O trimolecular reaction and the lowering of the barrier height with respect to the bimolecular reaction are encouraging; however, the sizable energy barrier indicates further study of the UF{sub 6} hydrolysis reaction

Automated multi-dimensional purification of tagged proteins.

Science.gov (United States)

Sigrell, Jill A; Eklund, Pär; Galin, Markus; Hedkvist, Lotta; Liljedahl, Pia; Johansson, Christine Markeland; Pless, Thomas; Torstenson, Karin

2003-01-01

The capacity for high throughput purification (HTP) is essential in fields such as structural genomics where large numbers of protein samples are routinely characterized in, for example, studies of structural determination, functionality and drug development. Proteins required for such analysis must be pure and homogenous and available in relatively large amounts. AKTA 3D system is a powerful automated protein purification system, which minimizes preparation, run-time and repetitive manual tasks. It has the capacity to purify up to 6 different His6- or GST-tagged proteins per day and can produce 1-50 mg protein per run at >90% purity. The success of automated protein purification increases with careful experimental planning. Protocol, columns and buffers need to be chosen with the final application area for the purified protein in mind.

A Scintillator Purification System for the Borexino Solar Neutrino Detector

OpenAIRE

Benziger, J.; Cadonati, L.; Calaprice, F.; Chen, M.; Corsi, A.; Dalnoki-Veress, F.; Fernholz, R.; Ford, R.; Galbiati, C.; Goretti, A.; Harding, E.; Ianni, Aldo; Ianni, Andrea; Kidner, S.; Leung, M.

2007-01-01

Purification of the 278 tons of liquid scintillator and 889 tons of buffer shielding for the Borexino solar neutrino detector was performed with a system that combined distillation, water extraction, gas stripping and filtration. The purification of the scintillator achieved unprecedented low backgrounds for the large scale liquid scintillation detector. This paper describes the principles of operation, design, construction and commissioning of the purification system, and reviews the require...

Improving the large scale purification of the HIV microbicide, griffithsin.

Science.gov (United States)

Fuqua, Joshua L; Wanga, Valentine; Palmer, Kenneth E

2015-02-22

Griffithsin is a broad spectrum antiviral lectin that inhibits viral entry and maturation processes through binding clusters of oligomannose glycans on viral envelope glycoproteins. An efficient, scaleable manufacturing process for griffithsin active pharmaceutical ingredient (API) is essential for particularly cost-sensitive products such as griffithsin -based topical microbicides for HIV-1 prevention in resource poor settings. Our previously published purification method used ceramic filtration followed by two chromatography steps, resulting in a protein recovery of 30%. Our objective was to develop a scalable purification method for griffithsin expressed in Nicotiana benthamiana plants that would increase yield, reduce production costs, and simplify manufacturing techniques. Considering the future need to transfer griffithsin manufacturing technology to resource poor areas, we chose to focus modifying the purification process, paying particular attention to introducing simple, low-cost, and scalable procedures such as use of temperature, pH, ion concentration, and filtration to enhance product recovery. We achieved >99% pure griffithsin API by generating the initial green juice extract in pH 4 buffer, heating the extract to 55°C, incubating overnight with a bentonite MgCl2 mixture, and final purification with Capto™ multimodal chromatography. Griffithsin extracted with this protocol maintains activity comparable to griffithsin purified by the previously published method and we are able to recover a substantially higher yield: 88 ± 5% of griffithsin from the initial extract. The method was scaled to produce gram quantities of griffithsin with high yields, low endotoxin levels, and low purification costs maintained. The methodology developed to purify griffithsin introduces and develops multiple tools for purification of recombinant proteins from plants at an industrial scale. These tools allow for robust cost-effective production and purification of

The Protein Maker: an automated system for high-throughput parallel purification

International Nuclear Information System (INIS)

Smith, Eric R.; Begley, Darren W.; Anderson, Vanessa; Raymond, Amy C.; Haffner, Taryn E.; Robinson, John I.; Edwards, Thomas E.; Duncan, Natalie; Gerdts, Cory J.; Mixon, Mark B.; Nollert, Peter; Staker, Bart L.; Stewart, Lance J.

2011-01-01

The Protein Maker instrument addresses a critical bottleneck in structural genomics by allowing automated purification and buffer testing of multiple protein targets in parallel with a single instrument. Here, the use of this instrument to (i) purify multiple influenza-virus proteins in parallel for crystallization trials and (ii) identify optimal lysis-buffer conditions prior to large-scale protein purification is described. The Protein Maker is an automated purification system developed by Emerald BioSystems for high-throughput parallel purification of proteins and antibodies. This instrument allows multiple load, wash and elution buffers to be used in parallel along independent lines for up to 24 individual samples. To demonstrate its utility, its use in the purification of five recombinant PB2 C-terminal domains from various subtypes of the influenza A virus is described. Three of these constructs crystallized and one diffracted X-rays to sufficient resolution for structure determination and deposition in the Protein Data Bank. Methods for screening lysis buffers for a cytochrome P450 from a pathogenic fungus prior to upscaling expression and purification are also described. The Protein Maker has become a valuable asset within the Seattle Structural Genomics Center for Infectious Disease (SSGCID) and hence is a potentially valuable tool for a variety of high-throughput protein-purification applications

Robotic high-throughput purification of affinity-tagged recombinant proteins.

Science.gov (United States)

Wiesler, Simone C; Weinzierl, Robert O J

2015-01-01

Affinity purification of recombinant proteins has become the method of choice to obtain good quantities and qualities of proteins for a variety of downstream biochemical applications. While manual or FPLC-assisted purification techniques are generally time-consuming and labor-intensive, the advent of high-throughput technologies and liquid handling robotics has simplified and accelerated this process significantly. Additionally, without the human factor as a potential source of error, automated purification protocols allow for the generation of large numbers of proteins simultaneously and under directly comparable conditions. The delivered material is ideal for activity comparisons of different variants of the same protein. Here, we present our strategy for the simultaneous purification of up to 24 affinity-tagged proteins for activity measurements in biochemical assays. The protocol described is suitable for the scale typically required in individual research laboratories.

Final programmatic environmental impact statement for alternative strategies for the long-term management and use of depleted uranium hexafluoride. Summary

International Nuclear Information System (INIS)

1999-04-01

This PEIS assesses the potential impacts of alternative management strategies for depleted uranium hexafluoride (UF 6 ) currently stored at three DOE sites: Paducah site near Paducah, Kentucky, Portsmouth site near Portsmouth, Ohio; and K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The alternatives analyzed in the PEIS include no action, long-term storage as UF 6 , long-term storage as uranium oxide, use as uranium oxide, use as uranium metal, and disposal. DOE's preferred alternative is to begin conversion of the depleted UF 6 inventory as soon as possible, either to uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible

Simplified riboprobe purification using translucent straws as gel tubes.

Science.gov (United States)

Kol, S; Ben-Shlomo, I; Adashi, E Y; Rohan, R M

1996-01-01

Gel purification of radioactive riboprobes enhances the quality of the ribonuclease protection assay. A simple and effective method for riboprobe purification is described. The method uses acrylamide gels in plastic tubes to achieve electrophoretic separation of the RNA polymerase products.

Purification and Characterization of Lipase from Aspergillus flavus ...

African Journals Online (AJOL)

USER

Abstract. Lipase from Aspergillus flavus was purified in a single step purification using MnFeO4 magnetic nano particles to achieve a 20.53- fold purification with specific activity of. 11.29 U/mg and a 59% recovery yield. SDS-PAGE of lipase showed a single pure band with corresponding molecular weight of 35 kDa.

Purification and Characterization of Lipase from Aspergillus flavus ...

African Journals Online (AJOL)

Lipase from Aspergillus flavus was purified in a single step purification using MnFeO4 magnetic nano particles to achieve a 20.53- fold purification with specific activity of 11.29 U/mg and a 59% recovery yield. SDS-PAGE of lipase showed a single pure band with corresponding molecular weight of 35 kDa. The optimal ...

Screening test of relays used under pressurized sulfur hexafluoride (SF6)

International Nuclear Information System (INIS)

Kutsukake, Kenichi; Matsuda, Makoto; Hanashima, Susumu; Obara, Kenjiro

2008-01-01

Many measurement and control devices inside of a high voltage terminal of the JAEA-Tokai tandem accelerator are operated under pressurized sulfur hexafluoride gas (SF 6 ) of 0.5 MPa. This screening test has been carried out to select a relay, which is usable under the pressurized SF 6 for turn on and off a large current of the devices, from commercial relays used in the atmospheric condition. Four kinds of relays were tested: electromechanical relay (EMR), magnet contactor (MAG), solid-state relay (SSR) and hybrid relay (HYB). Temperature and appearance changes of the relay were collected as measurement items. In addition, a reason of contact trouble of the relays was considered from the results of qualitative elementary analysis and observation of the contact surface using the EDS (energy-dispersive X-ray spectroscopy) and the SEM (scanning electron microscope). As a result, the EMR and the MAG showed irregular contact in spite of input voltage and electric current had fed to an operational coil of the relay normally. It is caused by the sulfide or fluoride compounds, which were formed by chemical reaction between metals and sulfur or hydrogen fluoride due to dissociation of SF 6 in electric arcs. On the other hand, the performance of the SSR and the HYB is better than the EMR and the MAG, and it was found that these relays are available in the pressurized SF 6 of 0.5MPa in spite of the standard specification. (author)

Virus purification by CsCl density gradient using general centrifugation.

Science.gov (United States)

Nasukawa, Tadahiro; Uchiyama, Jumpei; Taharaguchi, Satoshi; Ota, Sumire; Ujihara, Takako; Matsuzaki, Shigenobu; Murakami, Hironobu; Mizukami, Keijirou; Sakaguchi, Masahiro

2017-11-01

Virus purification by cesium chloride (CsCl) density gradient, which generally requires an expensive ultracentrifuge, is an essential technique in virology. Here, we optimized virus purification by CsCl density gradient using general centrifugation (40,000 × g, 2 h, 4 °C), which showed almost the same purification ability as conventional CsCl density gradient ultracentrifugation (100,000 × g, 1 h, 4 °C) using phages S13' and φEF24C. Moreover, adenovirus strain JM1/1 was also successfully purified by this method. We suggest that general centrifugation can become a less costly alternative to ultracentrifugation for virus purification by CsCl densiy gradient and will thus encourage research in virology.

Laboratory of minerals purification

International Nuclear Information System (INIS)

2002-01-01

The laboratory of minerals purification was organized in 1962 where with application of modern physical and chemical methods were investigated the mechanism of flotation reagents interaction with minerals' surface, was elaborated technologies on rising complexity of using of republic's minerals

Electrolysis of a nitrosyl hexafluoro-molybdate in anhydrous hydrogen fluoride

International Nuclear Information System (INIS)

Mougin, Jacques

1972-01-01

This thesis addresses the field of irradiated fuel reprocessing, and more particularly the study of the formation of molybdenum hexafluoride (MoF_6) by electrolysis of nitrosyl hexafluoro-molybdate (NOMoF_6) in solution in HF. The author presents the conditions of preparation of an electrolysis in anhydrous HF: solvent purification and control, production of a reference electrode, potential-kinetic study of the behaviour of materials selected for the electrode. The author then addresses the actual hydrolysis of the solution of nitrosyl hexafluoro-molybdate [fr

Waste water biological purification plants of dairy products industry and energy management

Science.gov (United States)

Stepanov, Sergey; Solkina, Olga; Stepanov, Alexander; Zhukova, Maria

2017-10-01

The paper presents results of engineering and economical comparison of waste water biological purification plants of dairy products industry. Three methods of purification are compared: traditional biological purification with the use of secondary clarifiers and afterpurification through granular-bed filters, biomembrane technology and physical-and-chemical treatment together with biomembrane technology for new construction conditions. The improvement of the biological purification technology using nitro-denitrification and membrane un-mixing of sludge mixture is a promising trend in this area. In these calculations, an energy management which is widely applied abroad was used. The descriptions of the three methods are illustrated with structural schemes. Costs of equipment and production areas are taken from manufacturers’ data. The research is aimed at an engineering and economical comparison of new constructions of waste water purification of dairy products industry. The experiment demonstrates advantages of biomembrane technology in waste water purification. This technology offers prospects of 122 million rubles cost saving during 25 years of operation when compared with of the technology of preparatory reagent flotation and of 13.7 million rubles cost saving compared to the option of traditional biological purification.

Draft Programmatic Environmental Impact Statement for alternative strategies for the long-term management and use of depleted uranium hexafluoride. Volume 1: Main text

International Nuclear Information System (INIS)

1997-12-01

This PEIS assesses the potential impacts of alternative management of alternative management strategies for depleted uranium hexafluoride (UF 6 ) currently stored at three DOE sites: Paducah site near Paducah, Kentucky; Portsmouth site near Portsmouth, Ohio; and K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The alternatives analyzed in the PEIS include no action, long-term storage as UF 6 , long-term storage as uranium oxide, use as uranium oxide, use as uranium metal, and disposal. The preferred alternative for the long-term management of depleted UF 6 is to use the entire inventory of material

Purification of human platelet-derived growth factor

International Nuclear Information System (INIS)

Raines, E.W.; Ross, R.

1985-01-01

The paper describes a method for purification of human platelet-derived growth factor (PDGF) from outdated platelet-rich plasma (PRP) using commonly available laboratory reagents and yielding a mitogen purified 800,000-fold over the starting material. [ 3 H]thymidine incorporation into DNA of cultured cells responsive to PDGF represents the most readily available method to follow its purification and define the biological activity of a purified preparation. Other assays to quantitate PDGF include radioreceptor assay and radioimmunoassay

Intensification of oily waste waters purification by means of liquid atomization

Science.gov (United States)

Eskin, A. A.; Tkach, N. S.; Kim, M. I.; Zakharov, G. A.

2017-10-01

In this research, a possibility of using liquid atomization for improving the efficiency of purification of wastewater by different methods has been studied. By the introduced method and an experimental setup for wastewater purification, saturation rate increases with its purification by means of dissolved air flotation. Liquid atomization under excess pressure allows to gain a large interfacial area between the saturated liquid and air, which may increase the rate of purified liquid saturation almost twice, compared to the existing methods of saturation. Current disadvantages of liquid atomization used for intensification of wastewater purification include high energy cost and secondary emulsion of polluting agents. It is also known that by means of liquid atomization a process of ozonizing can be intensified. Large contact surface between the purified liquid and ozone-air mixture increases the oxidizing efficiency, which allows to diminish ozone discharge. Liquid atomization may be used for purification of wastewaters by ultraviolet radiation. Small drops of liquid will be proportionally treated by ultraviolet, which makes it possible to do purification even of turbid wastewaters. High-speed liquid motion will prevent the pollution of quartz tubes of ultraviolet lamps.

Recent Advances in Nanoporous Membranes for Water Purification

Directory of Open Access Journals (Sweden)

Zhuqing Wang

2018-01-01

Full Text Available Nanoporous materials exhibit wide applications in the fields of electrocatalysis, nanodevice fabrication, energy, and environmental science, as well as analytical science. In this review, we present a summary of recent studies on nanoporous membranes for water purification application. The types and fabrication strategies of various nanoporous membranes are first introduced, and then the fabricated nanoporous membranes for removing various water pollutants, such as salt, metallic ions, anions, nanoparticles, organic chemicals, and biological substrates, are demonstrated and discussed. This work will be valuable for readers to understand the design and fabrication of various nanoporous membranes, and their potential purification mechanisms towards different water pollutants. In addition, it will be helpful for developing new nanoporous materials for quick, economic, and high-performance water purification.

Single-Step Affinity Purification for Fungal Proteomics ▿ †

OpenAIRE

Liu, Hui-Lin; Osmani, Aysha H.; Ukil, Leena; Son, Sunghun; Markossian, Sarine; Shen, Kuo-Fang; Govindaraghavan, Meera; Varadaraj, Archana; Hashmi, Shahr B.; De Souza, Colin P.; Osmani, Stephen A.

2010-01-01

A single-step protein affinity purification protocol using Aspergillus nidulans is described. Detailed protocols for cell breakage, affinity purification, and depending on the application, methods for protein release from affinity beads are provided. Examples defining the utility of the approaches, which should be widely applicable, are included.

Purification of radiolabeled RNA using sephadex G-15 or G-50 chromatography

International Nuclear Information System (INIS)

Yoo, Beong Gyu; Lee, Jong Seok

1998-01-01

We attempted to purify radiolabeled RNA using Sephadex G-15 and G-50 chromatography instead of commercial RNA purification kit. In the Sephadex G-15 chromatography the major portion of RNA was eluted in the fractions ranging from 3rd to 5th whereas broad elution profile of RNA was obtained from the Sephadex G-50 chromatography. The elution profile and purity of RNA obtained from Sephadex G-15 chromatography was very similar to that by commercial RNA purification kit. Furthermore, operating time required for purification of RNA by Sephadex G-15 was rather smaller than that by commercial kit. Overall results suggest that the purification of radiolabeled RNA using Sephadex G-15 is more money and time saving than using commercial RNA purification kit

Draft Programmatic Environmental Impact Statement for alternative strategies for the long-term management and use of depleted uranium hexafluoride. Volume 2: Appendices

International Nuclear Information System (INIS)

1997-12-01

This PEIS assesses the potential impacts of alternative management of alternative management strategies for depleted uranium hexafluoride (UF 6 ) currently stored at three DOE sites: Paducah site near Paducah, Kentucky; Portsmouth site near Portsmouth, Ohio; and K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The alternatives analyzed in the PEIS include no action, long-term storage as UF 6 , long-term storage as uranium oxide, use as uranium oxide, use as uranium metal, and disposal. The preferred alternative for the long-term management of depleted UF 6 is to use the entire inventory of material. This volume contains the appendices to volume I

A search for the sulphur hexafluoride cation with intense, few cycle laser pulses

Energy Technology Data Exchange (ETDEWEB)

Dota, Krithika; Mathur, Deepak, E-mail: atmol1@tifr.res.in [Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Mumbai 400 005 (India); Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Dharmadhikari, Aditya K. [Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Mumbai 400 005 (India); Dharmadhikari, Jayashree A. [Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Patra, Kaustuv; Tiwari, Ashwani K. [Indian Institute of Science Education and Research - Kolkata, Mohanpur 741 252 (India)

2013-11-21

It is well established that upon ionization of sulphur hexafluoride, the SF{sub 6}{sup +} ion is never observed in mass spectra. Recent work with ultrashort intense laser pulses has offered indications that when strong optical field are used, the resulting “bond hardening” can induce changes in the potential energy surfaces of molecular cations such that molecular ions that are normally unstable may, indeed, become metastable enough to enable their detection by mass spectrometry. Do intense, ultrashort laser pulses permit formation of SF{sub 6}{sup +}? We have utilized intense pulses of 5 fs, 11 fs, and 22 fs to explore this possibility. Our results are negative: no evidence is discovered for SF{sub 6}{sup +}. However, multiply charged sulphur and fluorine ions from highly charged SF{sub 6}{sup q+} ions are observed that enable us to resolve the controversy regarding the kinetic energy release accompanying formation of F{sup +} fragment ions. Quantum chemical computations of field-distorted potential energy curves of SF{sub 6} and its molecular ion enable us to rationalize our non-observation of SF{sub 6}{sup +}. Our findings have implications for high harmonic generation from SF{sub 6} in the few-cycle regime.

Stabilization of uranium hexafluoride by hydrolysis method for decommissioning of safeguard laboratory facility

Energy Technology Data Exchange (ETDEWEB)

Inagawa, Jun; Hotoku, Shinobu; Oda, Tetsuzo; Aoyagi, Noboru; Magara, Masaaki [Japan Atomic Energy Agency, Nuclear Science and Engineering Directorate, Tokai, Ibaraki (Japan)

2014-03-15

In safeguard laboratory (SGL) facility of Nuclear Science Research Institute of JAEA , uranium hexafluoride (UF{sub 6}) of enriched uranium of various enrichment was used for research and development of a spectrometric method for the determination of the enrichment of uranium in April 1983 through March 1993. After completion of this R and D, the UF{sub 6} has been stored in SGL facility. It was decided that the UF{sub 6} is carried to out of the facility, because the SGL facility will be decommissioning until March 2015. To transport and store in safety after transportation, it is necessary that the UF{sub 6} should be converted to stable chemical form. Hydrolysis of UF{sub 6} to uranyl fluoride (UO{sub 2}F{sub 2}) and evaporation to solid state were selected for the stabilization method. The equipment for hydrolysis and evaporation was installed in the SGL facility. Stabilization was operated in this equipment, and all of the UF{sub 6} in the SGL facility was converted to UO{sub 2}F{sub 2} solid state in October 2012 through August 2013. In this report, results of examination and operation for stabilization of UF{sub 6} were reported. (author)

Purification and characterization of three laccase isozymes from the ...

African Journals Online (AJOL)

2012-04-17

Apr 17, 2012 ... improve wine quality by removing fermentation inhibitors so as to increase yield of ethanol (Baldrian, 2006). They have also been used .... Summary of purification of laccase isozymes from Trametes sp. HS-03a. Purification .... and kinetics of a thermostable laccase from Pycnoporus sanguineus. (SCC 108).

Comparative study of peroxidase purification from apple and orange ...

African Journals Online (AJOL)

This paper reports the isolation and purification of peroxidase from low cost material; moreover, no significant work has been done on the isolation and purification of peroxidase from such cost effective sources (apple and orange seeds). Peroxidases had attracted considerable interest in recent years because of their ...

Development of Purification Protocol Specific for Bacteriocin 105B

Science.gov (United States)

2017-02-09

Bacillus anthracis. As the current application of broad-spectrum antimicrobials promotes the development of multi- drug resistant microorganisms...SPECTRUM TARGETED ANTIMICROBIALS ASSAYS PURIFICATION BACILLUS ANTHRACIS DRUG- RESISTANT MICROORGANISMS...through the purification procedure. The wide-spread use of broad-spectrum antimicrobial agents has led to the development of drug resistant

Ionic behavior of treated water at a water purification plant

OpenAIRE

Yanagida, Kazumi; Kawahigashi, Tatsuo

2012-01-01

[Abstract] Water at each processing stage in a water purification plant was extracted and analyzed to investigate changes of water quality. Investigations of water at each processing stage at the water purification plant are discussed herein.

Polyether sulfone/hydroxyapatite mixed matrix membranes for protein purification

Energy Technology Data Exchange (ETDEWEB)

Sun, Junfen, E-mail: junfensun@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Material Science and Engineering, Donghua University, North People Road 2999, Shanghai 201620 (China); Wu, Lishun [Department of Chemistry and Chemical Engineering, Heze University, Daxue Road 2269, Heze, Shandong Province 274015 (China)

2014-07-01

This work proposes a novel approach for protein purification from solution using mixed matrix membranes (MMMs) comprising of hydroxyapatite (HAP) inside polyether sulfone (PES) matrix. The influence of HAP particle loading on membrane morphology is studied. The MMMs are further characterized concerning permeability and adsorption capacity. The MMMs show purification of protein via both diffusion as well as adsorption, and show the potential of using MMMs for improvements in protein purification techniques. The bovine serum albumin (BSA) was used as a model protein. The properties and structures of MMMs prepared by immersion phase separation process were characterized by pure water flux, BSA adsorption and scanning electron microscopy (SEM).

High quality protein microarray using in situ protein purification

Directory of Open Access Journals (Sweden)

Fleischmann Robert D

2009-08-01

Full Text Available Abstract Background In the postgenomic era, high throughput protein expression and protein microarray technologies have progressed markedly permitting screening of therapeutic reagents and discovery of novel protein functions. Hexa-histidine is one of the most commonly used fusion tags for protein expression due to its small size and convenient purification via immobilized metal ion affinity chromatography (IMAC. This purification process has been adapted to the protein microarray format, but the quality of in situ His-tagged protein purification on slides has not been systematically evaluated. We established methods to determine the level of purification of such proteins on metal chelate-modified slide surfaces. Optimized in situ purification of His-tagged recombinant proteins has the potential to become the new gold standard for cost-effective generation of high-quality and high-density protein microarrays. Results Two slide surfaces were examined, chelated Cu2+ slides suspended on a polyethylene glycol (PEG coating and chelated Ni2+ slides immobilized on a support without PEG coating. Using PEG-coated chelated Cu2+ slides, consistently higher purities of recombinant proteins were measured. An optimized wash buffer (PBST composed of 10 mM phosphate buffer, 2.7 mM KCl, 140 mM NaCl and 0.05% Tween 20, pH 7.4, further improved protein purity levels. Using Escherichia coli cell lysates expressing 90 recombinant Streptococcus pneumoniae proteins, 73 proteins were successfully immobilized, and 66 proteins were in situ purified with greater than 90% purity. We identified several antigens among the in situ-purified proteins via assays with anti-S. pneumoniae rabbit antibodies and a human patient antiserum, as a demonstration project of large scale microarray-based immunoproteomics profiling. The methodology is compatible with higher throughput formats of in vivo protein expression, eliminates the need for resin-based purification and circumvents

Purification and fluorescent labeling of the human serotonin transporter

DEFF Research Database (Denmark)

Rasmussen, Søren G F; Gether, Ulrik

2005-01-01

To establish a purification procedure for the human serotonin transporter (hSERT) we expressed in Sf9 insect cells an epitope-tagged version of the transporter containing a FLAG epitope at the N-terminus and a polyhistidine tail at the C-terminus (FLAG-hSERT-12H). For purification, the transporter...

One-step purification of E. coli elongation factor Tu

DEFF Research Database (Denmark)

Knudsen, Charlotte Rohde; Clark, Brian F. C.; Degn, B

1993-01-01

The tuf A gene, encoding the E. coli elongation factor Tu, was cloned in the pGEX gene fusion system. Upon expression EF-Tu is fused to glutathione-S-transferase serving as a purification handle with affinity for glutathione immobilised on agarose. This allows purification of EF-Tu in a one...

Overview of the purification of recombinant proteins.

Science.gov (United States)

Wingfield, Paul T

2015-04-01

When the first version of this unit was written in 1995, protein purification of recombinant proteins was based on a variety of standard chromatographic methods and approaches, many of which were described and mentioned throughout Current Protocols in Protein Science. In the interim, there has been a shift toward an almost universal usage of the affinity or fusion tag. This may not be the case for biotechnology manufacture where affinity tags can complicate producing proteins under regulatory conditions. Regardless of the protein expression system, questions are asked as to which and how many affinity tags to use, where to attach them in the protein, and whether to engineer a self-cleavage system or simply leave them on. We will briefly address some of these issues. Also, although this overview focuses on E.coli, protein expression and purification, other commonly used expression systems are mentioned and, apart from cell-breakage methods, protein purification methods and strategies are essentially the same. Copyright © 2015 John Wiley & Sons, Inc.

Dense Medium Plasma Water Purification Reactor (DMP WaPR), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The Dense Medium Plasma Water Purification Reactor offers significant improvements over existing water purification technologies used in Advanced Life Support...

State-of-the-art technocology in blood purification at present

Directory of Open Access Journals (Sweden)

Zhi-hong LIU

2011-02-01

Full Text Available Objective To review the recent advancement in clinical practices and studies on blood purification techniques,and to provide a guide for further studies on its application in military medicine.Methods Literature published in recent five years limited to blood purification field either in English or Chinese were retrieved by searching PubMed and CHKD.Analysis and summary were performed based on the literature.Results The advancements in blood purification in recent five years could be categorized into four fields,i.e.hemodialysis(HD,peritoneal dialysis(PD,continuous renal replacement therapy(CRRT,and adsorption therapy.The development in HD was aimed at promoting the ability of removal of toxic elements producing uremia and online monitor techniques,and PD was aimed at improvement of patients’ general condition and intervention to reduce the risk factors affecting long-term outcomes,and preparation of new PD solutions to improve the efficacy of PD.In regard to CRRT,the current progress had been focused on initiation time,dose and proposal of new hypothesis for high-volume hemofiltration(HVHF application.Adsorption therapy was another choice of blood purification.Domestic military medicine progress in blood purification in our armed forces was focused on techniques that could be used in treatment of casualties in war,including the basic and clinical study of extracorporeal circuit intervention(ECI for treatment of critically ill patients,problems arising from anticoagulation in ECI for patients with trauma,chemical agents poisoning,and adsorption technique.Conclusions Recently,the main advancement of blood purification technique is combined application of series techniques such as dialysis,hemofiltration,adsorption,and plasma exchange in treatment of critically ill patients.Studies on blood purification in domestic military medicine should be updated continuously to follow closely to the latest achievement in world,and translate these latest

Purification of cerium, neodymium and gadolinium for low background experiments

Directory of Open Access Journals (Sweden)

Boiko R.S.

2014-01-01

Full Text Available Cerium, neodymium and gadolinium contain double beta active isotopes. The most interesting are 150Nd and 160Gd (promising for 0ν2β search, 136Ce (2β+ candidate with one of the highest Q2β. The main problem of compounds containing lanthanide elements is their high radioactive contamination by uranium, radium, actinium and thorium. The new generation 2β experiments require development of methods for a deep purification of lanthanides from the radioactive elements. A combination of physical and chemical methods was applied to purify cerium, neodymium and gadolinium. Liquid-liquid extraction technique was used to remove traces of Th and U from neodymium, gadolinium and for purification of cerium from Th, U, Ra and K. Co-precipitation and recrystallization methods were utilized for further reduction of the impurities. The radioactive contamination of the samples before and after the purification was tested by using ultra-low-background HPGe gamma spectrometry. As a result of the purification procedure the radioactive contamination of gadolinium oxide (a similar purification efficiency was reached also with cerium and neodymium oxides was decreased from 0.12 Bq/kg to 0.007 Bq/kg in 228Th, from 0.04 Bq/kg to <0.006 Bq/kg in 226Ra, and from 0.9 Bq/kg to 0.04 Bq/kg in 40K. The purification methods are much less efficient for chemically very similar radioactive elements like actinium, lanthanum and lutetium.

Uranium refining in South Africa. The production of uranium trioxide, considering raw material properties and nuclear purity requirements

International Nuclear Information System (INIS)

Colborn, R.P.; Bayne, D.L.G.; Slabber, M.N.

1980-01-01

Conventional practice results in raw materials being delivered to the uranium refineries in a form more suitable for transportation than for processing, and therefore the refineries are required to treat these raw materials to produce an acceptable intermediate feed stock. During this treatment, it is advantageous to include a purification step to ensure that the feed stock is of the required purity for nuclear grade uranium hexafluoride production, and this usually results in ammonium diuranate slurries of the required quality being produced as the intermediate feed stock. All subsequent processing steps can therefore be standardized and are effectively independent of the origin of the raw materials. It is established practice in South Africa to transport uranium as an ammonium diuranate slurry from the various mines to the Nufcor central processing plant for UOC production, and therefore the process for the production of uranium hexafluoride in South Africa was designed to take cognizance of existing transport techniques and to accept ammonium diuranate slurries as the raw material. The South African refinery will be able to process these slurries directly to uranium trioxide. This paper discusses the conditions under which the various ammonium diuranate raw materials, exhibiting a wide range of properties, can be effectively processed to produce a uranium trioxide of acceptably consistent properties. Mention is also made of the uranium hexafluoride distillation process adopted

Cadmium purification with a vibrating reactor

International Nuclear Information System (INIS)

Torres, N.; Esna-Ashari, M.; Biallas, H.; Kangas, K.

1986-01-01

While electrolytically producing zinc from sulfide concentrates, purification is the most significant step. Impurities such as Co, Sn, Ge, Ni and Sb can cause extensive redissolution of the electrodeposited zinc, thus diminishing current efficiency. Other metals, particularly cadmium, lead and copper, can negatively affect zinc properties by deposition on the cathode. It is standard practice to use atomized zinc dust as a reducing agent in the purification process, either alone or combined with additives. In conventional operations, special facilities are necessary to produce zinc dust in an amount close to 8wt% of cathode production. This paper examines a technique which makes use of zinc granules instead of dust

Specialists' meeting on fast reactor cover gas purification

International Nuclear Information System (INIS)

1987-01-01

The tentative agenda was adopted by the participants without comment and was followed throughout the meeting. The following topics were discussed at the subsequent sessions of the meeting on 'Fast Reactor Cover Gas Purification': National Position Papers; Impurities: Sources and Measurement; Cover Gas Purification Techniques; Sodium Aerosol Trapping; Radiological Considerations. Based on the papers presented and the discussions following, session summaries and conclusions were prepared and are included in this report

Specialists' meeting on fast reactor cover gas purification

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-07-01

The tentative agenda was adopted by the participants without comment and was followed throughout the meeting. The following topics were discussed at the subsequent sessions of the meeting on 'Fast Reactor Cover Gas Purification': National Position Papers; Impurities: Sources and Measurement; Cover Gas Purification Techniques; Sodium Aerosol Trapping; Radiological Considerations. Based on the papers presented and the discussions following, session summaries and conclusions were prepared and are included in this report.

A new helium gas recovery and purification system

International Nuclear Information System (INIS)

Yamamotot, T.; Suzuki, H.; Ishii, J.; Hamana, I.; Hayashi, S.; Mizutani, S.; Sanjo, S.

1974-01-01

A helium gas recovery and purification system, based on the principle of gas permeation through a membrane, is described. The system can be used for the purification of helium gas containing air as a contaminant. The apparatus, operating at ambient temperature does not need constant attention, the recovery ratio of helium gas is satisfactory and running costs are low. Gases other than helium can be processed with the apparatus. (U.K.)

Estimating the threshold levels of uranium and fluorine for the development of pulmonitis and toxic lung edema resultant from accidents involving uranium hexafluoride release

International Nuclear Information System (INIS)

Gasteva, G.N.; Antipin, E.B.; Bad'in, V.I.; Molokanov, A.A.; Mordasheva, V.V.; Mirkhajdarov, A.Kh.; Sorokin, A.V.; Savinova, I.A.

1999-01-01

Threshold doses of uranium and fluorine for the development of pulmonitis and toxic edema of the lung with lethal outcome are estimated. The levels of UF 6 entry under emergency conditions are evaluated and bronchopulmonary disease is described in subjects involved in three accidents with UF 6 release which occurred in the seventies and eighties, as shown by records. The results deny the previous assumption on the leading role of uranium in a single exposure to uranium hexafluoride. Fluorine ion triggering the mechanism of reactions in systems which determine the disease outcome is vitally important [ru

Recovery and purification of ethylene

Science.gov (United States)

Reyneke, Rian [Katy, TX; Foral, Michael J [Aurora, IL; Lee, Guang-Chung [Houston, TX; Eng, Wayne W. Y. [League City, TX; Sinclair, Iain [Warrington, GB; Lodgson, Jeffery S [Naperville, IL

2008-10-21

A process for the recovery and purification of ethylene and optionally propylene from a stream containing lighter and heavier components that employs an ethylene distributor column and a partially thermally coupled distributed distillation system.

New concept of gas purification by electron attachment

International Nuclear Information System (INIS)

Tamon, Hajime; Mizota, Hirotoshi; Sano, Noriaki; Schulze, S.; Okazaki, Morio

1995-01-01

Recently, the public has become interested in the following types of gas purification: (1) removal of indoor air pollutants; (2) complete removal of dioxin from incineration plants; (3) complete removal of radioactive iodine compounds; (4) simultaneous removal of NOx and SOx in exhaust gases from cogeneration plants; (5) removal and decomposition of halocarbons; (6) ultrahigh purification of gas sued for semiconductor industries. A new concept of gas purification by electron attachment is proposed. Low-energy electrons generated in a corona-discharge reactor are captured by electronegative impurities, producing negative ions. The ions drift to the anode in the electric field and are removed at the anode of the reactor. Two types of reactors were used to remove the negative ions: a deposition-type reactor, which deposits negative ions at the anode surface; a sweep-out-type reactor, which sweeps out enriched electronegative impurities through the porous anode. Removals of dilute sulfur compounds, oxygen and iodine from nitrogen were conducted to verify the concept of gas purification. Simulation models were used to estimate removal efficiencies of these compounds, by taking into account electron attachment, and experimental constants of the models were determined. The removal efficiency correlated by the models agreed well with the experimental one

The Blood Compatibilities of Blood Purification Membranes and Other Materials Developed in Japan

Directory of Open Access Journals (Sweden)

Takaya Abe

2011-01-01

Full Text Available The biocompatibilities in blood purification therapy are defined as “a concept to stipulate safety of blood purification therapy by an index based on interaction in the body arising from blood purification therapy itself.” The biocompatibilities are associated with not only materials to be used but also many factors such as sterilization method and eluted substance. It is often evaluated based on impacts on cellular pathways and on humoral pathways. Since the biocompatibilities of blood purification therapy in particular hemodialysis are not just a prognostic factor for dialysis patients but a contributory factor for long-term complications, it should be considered with adequate attention. It is important that blood purification therapy should be performed by consistently evaluating not only risks associated with these biocompatibilities but also the other advantages obtained from treatments. In this paper, the biocompatibilities of membrane and adsorption material based on Japanese original which are used for blood purification therapy are described.

Re-purification of labelled ferritin antigen with HPLC

International Nuclear Information System (INIS)

Zhang Haoyi; Jin Lichun

2002-01-01

Objective: To improve the quality of long-term stored labelled ferritin antigen with HPLC. Methods: The antigen was analyzed and purified with HPLC and again analyzed with RIA afterwards. Results: Ferritin antigen underwent significant polymerization after long-term (aggregation) storage. After re-purification with HPLC, its immuno-activity and labelled specific radioactivity were both significantly improved. Conclusion: Quality of stored ferritin RIA kit could be greatly improved after re-purification with HPLC

The entanglement purification for entangled multi-particle states

CERN Document Server

Ye, Liu; Guo Guang Can

2002-01-01

We present two purification schemes for nonmaximally entangled states. We first show that two parties, Alice and Bob, start with shared less-entangled three-particle states to probabilistically produce a three-particle Greenberger-Horne-Zeilinger state by Bell state measurements and positive operator valued measure (POVM) or a unitary transformation. Then, by a straightforward generalization of the schemes, the purification of a multi-particle entangled state can be realized. 25 Refs. --- 35 --- AN

Overview of the recombinant proteins purification by affinity tags and ...

African Journals Online (AJOL)

From protein within isolation process which the same matter increases labor costs further and prevents application of these tags in industrial scale. Therefore proper replacement is emphasized for enzymatic removal of purification tags. Keywords: protein purification; recombinant proteins; self-cleavable tags; Intein tags; ...

PURIFICATION AND CHARACTERIZATION OF POLY-HYDROXYBUTYRATE (PHB IN CUPRIAVIDUS NECATOR

Directory of Open Access Journals (Sweden)

Sergio Leon De Rooy

2010-06-01

Full Text Available Purification and characterization of biodegradable plastic namely Polyhydroxybutyrate (PHB in Cupriavidus necator have been carried out. C. necator was grown on a Ramsay medium with fixed substrate conditions and optimized for time. Stepwise purification of PHB was carried out, by using hydrogen peroxide and chloroform. The effect of temperature, time, and hydrogen peroxide concentration on the purification were also evaluated. The extracted PHB was studied with XRD, FTIR and 1H-NMR and 13C-NMR to determine its structure and purity. Yield and crystallinity were also studied with HPLC and XRD, respectively. The results of the research showed that higher concentrations of hydrogen peroxide gave better yields, whereas higher temperatures and longer lysis times led to different results. Higher crystallinity was observed when purification temperatures were elevated, but higher hydrogen peroxide concentration and longer extraction time gave varying crystallinity. The highest yield ca 66.10 % DCW was reached by purification using H2O2 20 %, at 100 oC for 2 h. The results of   TGA analysis indicated that the purity of the PHB obtained was about 75 % and by using DSC, it was found that the PHB showed good thermal properties.   Keywords:  PHB, recovery, hydrogen peroxide, characterization

Feasibility Study on Manufacturing Lightweight Aggregates from Water Purification Sludge

Science.gov (United States)

Peng, Ching-Fang; Chen, How-Ji

2018-02-01

This study mainly discussed the feasibility of manufacturing lightweight aggregates from water purification sludge in Taiwan. They were analysed for the physical and chemical composition before the sintering test for lightweight aggregates in a laboratory. Then the physical and mechanical properties of the synthesized aggregates were assessed. The result showed that the chemical composition of sludge in the water purification plants was within the appropriate range for manufacturing lightweight aggregate as proposed in the literature. The sintering test demonstrated that the particle density of aggregates from the ten types of water purification sludge were mostly less than 1.8 g/cm3. In addition, the dry unit weight, the organic impurity, the ignition loss, and other characteristics of synthesized aggregates met the requirement of CNS standards, while its water absorption and crushing strength also fulfilled the general commercial specifications. Therefore, reclamation of water purification sludge for production of lightweight aggregate is indeed feasible.

Bromelain: an overview of industrial application and purification strategies.

Science.gov (United States)

Arshad, Zatul Iffah Mohd; Amid, Azura; Yusof, Faridah; Jaswir, Irwandi; Ahmad, Kausar; Loke, Show Pau

2014-09-01

This review highlights the use of bromelain in various applications with up-to-date literature on the purification of bromelain from pineapple fruit and waste such as peel, core, crown, and leaves. Bromelain, a cysteine protease, has been exploited commercially in many applications in the food, beverage, tenderization, cosmetic, pharmaceutical, and textile industries. Researchers worldwide have been directing their interest to purification strategies by applying conventional and modern approaches, such as manipulating the pH, affinity, hydrophobicity, and temperature conditions in accord with the unique properties of bromelain. The amount of downstream processing will depend on its intended application in industries. The breakthrough of recombinant DNA technology has facilitated the large-scale production and purification of recombinant bromelain for novel applications in the future.

One-step deterministic multipartite entanglement purification with linear optics

Energy Technology Data Exchange (ETDEWEB)

Sheng, Yu-Bo [Department of Physics, Tsinghua University, Beijing 100084 (China); Long, Gui Lu, E-mail: gllong@tsinghua.edu.cn [Department of Physics, Tsinghua University, Beijing 100084 (China); Center for Atomic and Molecular NanoSciences, Tsinghua University, Beijing 100084 (China); Key Laboratory for Quantum Information and Measurements, Beijing 100084 (China); Deng, Fu-Guo [Department of Physics, Applied Optics Beijing Area Major Laboratory, Beijing Normal University, Beijing 100875 (China)

2012-01-09

We present a one-step deterministic multipartite entanglement purification scheme for an N-photon system in a Greenberger–Horne–Zeilinger state with linear optical elements. The parties in quantum communication can in principle obtain a maximally entangled state from each N-photon system with a success probability of 100%. That is, it does not consume the less-entangled photon systems largely, which is far different from other multipartite entanglement purification schemes. This feature maybe make this scheme more feasible in practical applications. -- Highlights: ► We proposed a deterministic entanglement purification scheme for GHZ states. ► The scheme uses only linear optical elements and has a success probability of 100%. ► The scheme gives a purified GHZ state in just one-step.

Evaluation of health effects in Sequoyah Fuels Corporation workers from accidental exposure to uranium hexafluoride

International Nuclear Information System (INIS)

Fisher, D.R.; Swint, M.J.; Kathren, R.L.

1990-05-01

Urine bioassay measurements for uranium and medical laboratory results were studied to determine whether there were any health effects from uranium intake among a group of 31 workers exposed to uranium hexafluoride (UF 6 ) and hydrolysis products following the accidental rupture of a 14-ton shipping cylinder in early 1986 at the Sequoyah Fuels Corporation uranium conversion facility in Gore, Oklahoma. Physiological indicators studied to detect kidney tissue damage included tests for urinary protein, casts and cells, blood, specific gravity, and urine pH, blood urea nitrogen, and blood creatinine. We concluded after reviewing two years of follow-up medical data that none of the 31 workers sustained any observable health effects from exposure to uranium. The early excretion of uranium in urine showed more rapid systemic uptake of uranium from the lung than is assumed using the International Commission on Radiological Protection (ICRP) Publication 30 and Publication 54 models. The urinary excretion data from these workers were used to develop an improved systemic recycling model for inhaled soluble uranium. We estimated initial intakes, clearance rates, kidney burdens, and resulting radiation doses to lungs, kidneys, and bone surfaces. 38 refs., 10 figs., 7 tabs

Evaluation of health effects in Sequoyah Fuels Corporation workers from accidental exposure to uranium hexafluoride

Energy Technology Data Exchange (ETDEWEB)

Fisher, D.R. (Pacific Northwest Lab., Richland, WA (USA)); Swint, M.J.; Kathren, R.L. (Hanford Environmental Health Foundation, Richland, WA (USA))

1990-05-01

Urine bioassay measurements for uranium and medical laboratory results were studied to determine whether there were any health effects from uranium intake among a group of 31 workers exposed to uranium hexafluoride (UF{sub 6}) and hydrolysis products following the accidental rupture of a 14-ton shipping cylinder in early 1986 at the Sequoyah Fuels Corporation uranium conversion facility in Gore, Oklahoma. Physiological indicators studied to detect kidney tissue damage included tests for urinary protein, casts and cells, blood, specific gravity, and urine pH, blood urea nitrogen, and blood creatinine. We concluded after reviewing two years of follow-up medical data that none of the 31 workers sustained any observable health effects from exposure to uranium. The early excretion of uranium in urine showed more rapid systemic uptake of uranium from the lung than is assumed using the International Commission on Radiological Protection (ICRP) Publication 30 and Publication 54 models. The urinary excretion data from these workers were used to develop an improved systemic recycling model for inhaled soluble uranium. We estimated initial intakes, clearance rates, kidney burdens, and resulting radiation doses to lungs, kidneys, and bone surfaces. 38 refs., 10 figs., 7 tabs.

Rotary adsorbers for waste air purification and solvent recovery

International Nuclear Information System (INIS)

Konrad, G.; Eigenberger, G.

1994-01-01

Rotary Adsorbers for Waste Air Purification and Solvent Recovery. Thanks to their compact construction and low pressure drops, adsorbers with rotating adsorbent beds are highly suitable both for retrofitting of waste air purification units and generally for the removal of absorbable components from gas streams. When used in conjunction with straightforward hot gas desorption they permit almost complete purification of gas flows with concomitant concentration of the separated components in the desorbate by a factor of 10 to 20. They can also be used in conjunction with recovery of the separated components by partial condensation of the desorbate. Owing to the fixed coupling of adsorption and desorption times, which is determined by the geometry of the unit, the behaviour of the system is distinctly different from that of conventional multiple bed systems in cyclic operation. A detailed model description and computer simulation of operating behaviour are particularly useful for their analysis. It is shown that the behaviour of commercially available rotor concepts can be much better understood in this way and new concepts for exhaust air purification with integrated solvent recovery can be developed which are characterised by significantly reduced energy requirements for desorption and condensation. (orig.) [de

Kinetics of the tungsten hexafluoride-silane reaction for the chemical vapor deposition of tungsten

International Nuclear Information System (INIS)

Gokce, Huseyin.

1991-01-01

In this study, the kinetics of the low-pressure chemical vapor deposition (LPCVD) of tungsten by silane reduction of tungsten hexafluoride on Si(100) surfaces was studied. A single-wafer, cold-wall reactor was sued for the experiments. The SiH 4 /WF 6 ratio was 1.0. The pressure and temperature range were 1-10 torr and 137-385 degree C, respectively. Kinetic data were obtained in the absence of mass-transfer effects. The film thicknesses were measured by gravimetry. Scanning electron microscopy (SEM), Auger electron spectroscopy (AES), x-ray diffraction (XRD), and resistivity measurements were used to analyze the W films. For the horizontal substrate position and 4-minute reaction times, the apparent activation energies were determined to be 0.35 eV/atom for 10 torr, 0.17 eV/atom for 3 torr, and 0.08 eV/atom for 1 torr. Lower temperatures and higher pressures produced porous films, while higher temperatures and lower pressures resulted in continuous films with smoother surfaces. As the Si-W interface, a W(110) preferential orientation was observed. As the W films grew thicker, W orientation switched from (110) to (100). Apparent activation energy seems to change with thickness

Generation, concentration and purification for ionic entangled states

International Nuclear Information System (INIS)

Yang Ming; Cao Zhuoliang

2007-01-01

In cavity QED, the atoms would be sent through the sequential arrays of cavities for the generation of multi-cavity entanglement, or several atoms would be sent into the same cavity mode one bye one for the generation of multi-atom entanglement. The complexity of these processes will impose limitations on the experimental feasibility of it. So, following our previous publication [International Journal Of Quantum Information 2, 231 (2004)] we will propose an alternative scheme for the preparation of multi-cavity W state via cavity QED, which uses the geometrical method to do what other authors have proposed previously using sequential arrays of cavities. Due to the impossibility that one quantum system can be isolated from the environment absolutely, the entanglement of the entangled objects will decrease exponentially with the propagating distance of the objects, and the practically available quantum entangled states are all non-maximally entangled states or the more general case--mixed states. Following our previous publications [Phys. Rev. A 72, 042307 (2005), ibid. 71, 012308 (2005)], we will propose an entanglement generation, concentration and purification scheme for atomic or ionic system, which is mainly based on Cavity QED and linear optical elements. This purification process avoids the controlled-NOT (C-NOT) operations needed in the original purification protocol, which simplifies the whole purification process

Early days of tRNA research: Discovery, function, purification and ...

Indian Academy of Sciences (India)

Madhu

2006-10-04

Oct 4, 2006 ... function in protein synthesis and methods for its purification ... intermediate carrier of the amino acid in protein synthesis. (table 1). .... 14C-leucine were incubated with GTP, PEP, and pyruvate kinase as indicated (adapted from: Hoagland et al 1958). .... Purification of N. crassa mitochondrial initiator tRNA.

Metabolic fate and evaluation of injury in rats and dogs following exposure to the hydrolysis products of uranium hexafluoride: implications for a bioassay program related to potential releases of uranium hexafluoride, July 1979-October 1981

International Nuclear Information System (INIS)

Morrow, P.E.; Leach, L.J.; Smith, F.A.

1982-12-01

This final report summarizes the experimental studies undertaken in rats and dogs in order to help provide adequate biological bases for quantifying and evaluating uranium hexafluoride (UF 6 ) exposures. Animals were administered the hydrolysis products of UF 6 by inhalation exposures, intratracheal instillations and intravenous injections. Attention was given to dose-effect relationships appropriate to the kidney, the unique site of subacute toxicity; to the rates of uranium excretion; and to uranium retention in renal tissue. These criteria were examined in both naive and multiply-exposed animals. The findings of these studies partly substantiate the ICRP excretion model for hexavalent uranium; generally provide a lower renal injury threshold concentration than implicit in the MPC for natural uranium; indicate distinctions in response (for example, uranium excretion) are based on exposure history; compare and evaluate various biochemical indices of renal injury; raise uncertainties about prevailing views of reversible renal injury, renal tolerance and possible hydrogen fluoride synergism with uranium effects; and reveal species differences in several areas, for example, renal retention of uranium. While these studies present some complicating features to extant bioassay practice, they nevertheless supply data supportive of the bioassay concept

Method to separate hydrogen fluoride from an uranium hexafluoride-hydrogen fluoride mixture

International Nuclear Information System (INIS)

Pfistermeister, M.; Jokar, J.

1978-01-01

It is difficult to separate off HF in the purification of UF 6 from additional compounds. According to the invention, it is possible without too greater effort to form the hardly volatile tri-(perfluorobutyl)-ammonium fluoride by adding a perfluorate amine or a derivate of it, and then to separate off the UF 6 from the adduct by simple distillation or sublimation. The adduct can be easily split again with NaOH, so that the amine can be used again without loss. (RW) [de

Health physics system scheme for the uranium purification plant

International Nuclear Information System (INIS)

Meyer, M.; Oliveira, E.C.; Sordi, G.A.A.; Abrao, A.

1976-01-01

After describing the two uranium purification processes used in the Chemical Engineerring Division of the Instituto de Energia Atomica, it is examined the possible hazards and methods to control or eliminate them. Since these purification process present several stages, in each one of them it is evaluated the hazards and tried to give adequate solutions to protect both, personnel and installations, from the potential radiation hazards

Economic Methods of Ginger Protease'sextraction and Purification

Science.gov (United States)

Qiao, Yuanyuan; Tong, Junfeng; Wei, Siqing; Du, Xinyong; Tang, Xiaozhen

This article reports the ginger protease extraction and purification methods from fresh ginger rhizome. As to ginger protease extraction, we adapt the steps of organic solvent dissolving, ammonium sulfate depositing and freeze-drying, and this method can attain crude enzyme powder 0.6% weight of fresh ginger rhizome. The purification part in this study includes two steps: cellulose ion exchange (DEAE-52) and SP-Sephadex 50 chromatography, which can purify crude ginger protease through ion and molecular weight differences respectively.

Purification of thyrotropin from human hypophysis: preliminary preparation

International Nuclear Information System (INIS)

Borghi, V.C.; Lin, L.H.; Bartolini, P.

1988-07-01

The adequacy of stored crude preparations for isolation of human tyrotropin (TSH) was evaluated according to Ross et al from a side fraction obtained during the purification of growth hormone from frozen pituitaries (SOMATORMON). Six crude TSH preparations were stored at - 20 0 C during several years for further purification. One of these preparations was purified by sucessive chromatographies on Sephadex G-100, hydroxylapatite and SP-Sephadex C50. The TSH content present in the chromatographic fractions and in the pools was assayed by specific radioimmunoassay developed at our laboratory. The protein determination of the fractions and pools was performed by absorbance at 280 nm and by the method of Lowry at al, respectively. The TSH activity increased eight times during the purification and the TSH purified had a radioimmunological potency around half that de scribed by Roos at al. The results suggest the fitness of long time stored preparations in the attainment of pure TSH. (author) [pt

Improving the technology of purification of gas emissions petrochemical industries

OpenAIRE

USMANOVA R.R.; ZAIKOV G.E.

2014-01-01

The technology of cleaning of gas emissions flares in the production of synthetic rubber. Developed dynamic scrubber for scrubbing gas emissions. Complex studies served as the basis for the design of an air purification system of industrial premises. Purification of gas emissions before combustion in flares has significantly reduced air pollution by toxic substances.

Final programmatic environmental impact statement for alternative strategies for the long-term management and use of depleted uranium hexafluoride. Volume 1: Main text

International Nuclear Information System (INIS)

1999-04-01

This PEIS assesses the potential impacts of alternative management strategies for depleted uranium hexafluoride (UF 6 ) currently stored at three DOE sites: Paducah site near Paducah, Kentucky, Portsmouth site near Portsmouth, Ohio; and K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The alternatives analyzed in the PEIS include no action, long-term storage as UF 6 , long-term storage as uranium oxide, use as uranium oxide, use as uranium metal, and disposal. DOE's preferred alternative is to begin conversion of the depleted UF 6 inventory as soon as possible, either to uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible

Advanced purification of petroleum refinery wastewater by catalytic vacuum distillation.

Science.gov (United States)

Yan, Long; Ma, Hongzhu; Wang, Bo; Mao, Wei; Chen, Yashao

2010-06-15

In our work, a new process, catalytic vacuum distillation (CVD) was utilized for purification of petroleum refinery wastewater that was characteristic of high chemical oxygen demand (COD) and salinity. Moreover, various common promoters, like FeCl(3), kaolin, H(2)SO(4) and NaOH were investigated to improve the purification efficiency of CVD. Here, the purification efficiency was estimated by COD testing, electrolytic conductivity, UV-vis spectrum, gas chromatography-mass spectrometry (GC-MS) and pH value. The results showed that NaOH promoted CVD displayed higher efficiency in purification of refinery wastewater than other systems, where the pellucid effluents with low salinity and high COD removal efficiency (99%) were obtained after treatment, and the corresponding pH values of effluents varied from 7 to 9. Furthermore, environment estimation was also tested and the results showed that the effluent had no influence on plant growth. Thus, based on satisfied removal efficiency of COD and salinity achieved simultaneously, NaOH promoted CVD process is an effective approach to purify petroleum refinery wastewater. Copyright 2010 Elsevier B.V. All rights reserved.

[Pilot-scale purification of lipopeptide from marine-derived Bacillus marinus].

Science.gov (United States)

Gu, Kangbo; Guan, Cheng; Xu, Jiahui; Li, Shulan; Luo, Yuanchan; Shen, Guomin; Zhang, Daojing; Li, Yuanguang

2016-11-25

This research was aimed at establishing the pilot-scale purification technology of lipopeptide from marine-derived Bacillus marinus. We studied lipopeptide surfactivity interferences on scale-up unit technologies including acid precipitation, methanol extraction, solvent precipitation, salting out, extraction, silica gel column chromatography and HZ806 macroporous absorption resin column chromatography. Then, the unit technologies were combined in a certain order, to remove the impurities gradually, and to gain purified lipopeptide finally, with high recovery rate throughout the whole process. The novel pilot-scale purification technology could effectively isolate and purify lipopeptide with 87.51% to 100% purity in hectograms from 1 ton of Bacillus marinus B-9987 fermentation broth with more than 81.73% recovery rate. The first practical hectogram production of highly purified lipopeptide derived from Bacillus marinus was achieved. With this new purification method, using complex media became possible in fermentation process to reduce the fermentation cost and scale-up the purification for lipopeptide production. For practicability and economy, foaming problem resulting from massive water evaporation was avoided in this technology.

Experimental Study on Purification of Low Grade Diatomite

Science.gov (United States)

Xiao, Liguang; Pang, Bo

2017-04-01

This paper presented an innovation for purification of low grade diatomite(DE) by grinding, ultrasonic pretreatment, acid leaching of closed stirring and calcination. The optimum process parameters of DE purification were obtained, the characterizations of original and purified DE were determined by SEM and BET. The results showed that the specific surface area of DE increased from 12.65m2/g to 23.23m2/g, which increased by 45.54%. SEM analysis revealed that the pore structure of purified DE was dredged highly.

Small scale extraction and purification of human prolactin for the preparation of radioimmunoassay reagents

International Nuclear Information System (INIS)

Dias, L.E.M.F.

1989-01-01

Purification of human prolactin from pituitaries was carried out in our laboratory to obtain a pure reagent for use in RIA. The extraction and purification procedure was adapted from the method of Mc. Lean et al., and it involves the following steps: 1. Extraction of frozen pituitaries in buffers 0.14M phosphate/citrate pH 4.0 and 0.05M ammonium acetate pH 10.0. 2. Purification by hydrophobic interaction chromatography on Phenyl-Sepharose CL-4B in the presence of acetonitrile. 3. Purification by anion exchange chromatography on DEAE-Sepharose Cl-68. The purification method is considered effective for obtaining a hPrl of the purity needed for radioassay purposes, having the advantage of rapidity and relative simplicity. (author) [pt

Rotating Reverse-Osmosis for Water Purification

Science.gov (United States)

Lueptow, RIchard M.

2004-01-01

A new design for a water-filtering device combines rotating filtration with reverse osmosis to create a rotating reverse- osmosis system. Rotating filtration has been used for separating plasma from whole blood, while reverse osmosis has been used in purification of water and in some chemical processes. Reverse- osmosis membranes are vulnerable to concentration polarization a type of fouling in which the chemicals meant not to pass through the reverse-osmosis membranes accumulate very near the surfaces of the membranes. The combination of rotating filtration and reverse osmosis is intended to prevent concentration polarization and thereby increase the desired flux of filtered water while decreasing the likelihood of passage of undesired chemical species through the filter. Devices based on this concept could be useful in a variety of commercial applications, including purification and desalination of drinking water, purification of pharmaceutical process water, treatment of household and industrial wastewater, and treatment of industrial process water. A rotating filter consists of a cylindrical porous microfilter rotating within a stationary concentric cylindrical outer shell (see figure). The aqueous suspension enters one end of the annulus between the inner and outer cylinders. Filtrate passes through the rotating cylindrical microfilter and is removed via a hollow shaft. The concentrated suspension is removed at the end of the annulus opposite the end where the suspension entered.

Final programmatic environmental impact statement for alternative strategies for the long-term management and use of depleted uranium hexafluoride. Volume 2: Appendices

International Nuclear Information System (INIS)

1999-04-01

This PEIS assesses the potential impacts of alternative management strategies for depleted uranium hexafluoride (UF 6 ) currently stored at three DOE sites: Paducah site near Paducah, Kentucky, Portsmouth site near Portsmouth, Ohio; and K-25 site on the Oak Ridge Reservation, Oak Ridge, Tennessee. The alternatives analyzed in the PEIS include no action, long-term storage as UF 6 , long-term storage as uranium oxide, use as uranium oxide, use as uranium metal, and disposal. DOE's preferred alternative is to begin conversion of the depleted UF 6 inventory as soon as possible, either to uranium oxide, uranium metal, or a combination of both, while allowing for use of as much of this inventory as possible. This volume contains Appendices A--O

Multi-copy entanglement purification with practical spontaneous parametric down conversion sources

International Nuclear Information System (INIS)

Zhang Shuai-Shuai; Shu Qi; Sheng Yu-Bo; Zhou Lan

2017-01-01

Entanglement purification is to distill the high quality entanglement from the low quality entanglement with local operations and classical communications. It is one of the key technologies in long-distance quantum communication. We discuss an entanglement purification protocol (EPP) with spontaneous parametric down conversion (SPDC) sources, in contrast to previous EPP with multi-copy mixed states, which requires ideal entanglement sources. We show that the SPDC source is not an obstacle for purification, but can benefit the fidelity of the purified mixed state. This EPP works for linear optics and is feasible in current experiment technology. (paper)

Heparin-binding peptide as a novel affinity tag for purification of recombinant proteins.

Science.gov (United States)

Morris, Jacqueline; Jayanthi, Srinivas; Langston, Rebekah; Daily, Anna; Kight, Alicia; McNabb, David S; Henry, Ralph; Kumar, Thallapuranam Krishnaswamy Suresh

2016-10-01

Purification of recombinant proteins constitutes a significant part of the downstream processing in biopharmaceutical industries. Major costs involved in the production of bio-therapeutics mainly depend on the number of purification steps used during the downstream process. Affinity chromatography is a widely used method for the purification of recombinant proteins expressed in different expression host platforms. Recombinant protein purification is achieved by fusing appropriate affinity tags to either N- or C- terminus of the target recombinant proteins. Currently available protein/peptide affinity tags have proved quite useful in the purification of recombinant proteins. However, these affinity tags suffer from specific limitations in their use under different conditions of purification. In this study, we have designed a novel 34-amino acid heparin-binding affinity tag (HB-tag) for the purification of recombinant proteins expressed in Escherichia coli (E. coli) cells. HB-tag fused recombinant proteins were overexpressed in E. coli in high yields. A one-step heparin-Sepharose-based affinity chromatography protocol was developed to purify HB-fused recombinant proteins to homogeneity using a simple sodium chloride step gradient elution. The HB-tag has also been shown to facilitate the purification of target recombinant proteins from their 8 M urea denatured state(s). The HB-tag has been demonstrated to be successfully released from the fusion protein by an appropriate protease treatment to obtain the recombinant target protein(s) in high yields. Results of the two-dimensional NMR spectroscopy experiments indicate that the purified recombinant target protein(s) exist in the native conformation. Polyclonal antibodies raised against the HB-peptide sequence, exhibited high binding specificity and sensitivity to the HB-fused recombinant proteins (∼10 ng) in different crude cell extracts obtained from diverse expression hosts. In our opinion, the HB-tag provides a

Use of organophilic clays in purification of oily wastewater; Uso de argilas organofilicas na purificacao de efluentes oleosos

Energy Technology Data Exchange (ETDEWEB)

Silva, A.A. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Engenharia de Processos], email: adriana_anp@yahoo.com.br; Pereira, K.R de O.; Wiebeck, H.; Valenzuela-Diaz, F.R. [Universidade de Sao Paulo (EPUSP), SP (Brazil). Escola Politecnica. Dept. de Engenharia Metalurgica e de Materiais; Rodrigues, M. G.F. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). CCT. Dept. de Engenharia Quimica

2006-07-01

Water mixed with oil is produced in great volume in industrial processes and in petroleum refineries. This mixture must be treated to return to environment or can be reused in the same process. The refine of this water is expensive and presents a difficult execution. The process of separation of oil in water used organophilic clays can be a new option. In this work, the process of preparation of organophilic clays using smectitic clay polycationic and a industrial sodium bentonite both from Paraiba State, Brazil is described. The samples were characterized by two techniques: X-ray Diffraction and Thermal Analysis. After preparation of the organophilic clays it was determined theirs swelling in organic solvents and oil adsorption capacity. The organophilic clays presented higher capacity of oil adsorption when compared to activated carbon. (author)

Sodium purification in Rapsodie

International Nuclear Information System (INIS)

Giraud, B.

1968-01-01

This report is one of a series of publications presenting the main results of tests carried out during the start-up of the first french fast neutron reactor: Rapsodie. The article presents the sodium purification techniques used in the reactor cooling circuits both from the constructional point of view and with respect to results obtained during the first years working. (author) [fr

The IAEA recommendations for providing protection during the transport of uranium hexafluoride

International Nuclear Information System (INIS)

Levin, I.; Wieser, K.

1988-01-01

The Regulations for the safe transport of radioactive materials, are the basis of national and international regulations concerning this subject throughout the world. These regulations require that subsidiary hazards associated with radioactive materials should also be considered. Other national and international regulations concerning the transport of dangerous materials consider that a radioactive material having other dangerous properties should be classified as class 7. Following this line and acting upon the recommendations of SAGSTRAM (Standing Advisory Committee on the Safe Transport of Radioactive Materials) that the Agency should take the lead in providing guidance to Member States with respect to UF 6 packaging and transport, the Agency convened two expert meetings during 1986 and 1987 in order to look into the special problems associated with the transport of uranium hexafluoride. The experts identified several areas in which additional safety measures should be considered if the transport of UF 6 is to have a non-radiological safety level consistent with that of its radiological risks. In this presentation the new recommendations are described. The main safety issues to be discussed are fire resistance, valve protection and compatibility with service and structural equipment. Another aspect of importance is the interface between the process and the transport phases, bearing in mind that the same containers are used in both. This paper also reveals how far the new recommendations concerning UF 6 have already been endorsed in the forthcoming European Transport Regulations (ADR/RID) together with the 1985 revised Edition of IAEA Safety Series No. 6

Synthesis Gas Purification Purification des gaz de synthèse

Directory of Open Access Journals (Sweden)

Chiche D.

2013-10-01

Full Text Available Fischer-Tropsch (FT based B-XTL processes are attractive alternatives for future energy production. These processes aim at converting lignocellulosic biomass possibly in co-processing with petcoke, coal, or vacuum residues into synthetic biofuels. A gasification step converts the feed into a synthesis gas (CO and H2 mixture , which undergoes the Fischer-Tropsch reaction after H2/CO ratio adjustment and CO2 removal. However synthesis gas also contains various impurities that must be removed in order to prevent Fischer-Tropsch catalyst poisoning. Due to the large feedstocks variety that can be processed, significant variations of the composition of the synthesis gas are expected. Especially, this affects the nature of the impurities that are present (element, speciation, as well as their relative contents. Moreover, due to high FT catalyst sensitivity, severe syngas specifications regarding its purity are required. For these reasons, synthesis gas purification constitutes a major challenge for the development of B-XTL processes. In this article, we focus on these major hurdles that have to be overcome. The different kinds of syngas impurities are presented. The influence of the nature of feedstocks, gasification technology and operating conditions on the type and content of impurities is discussed. Highlight is given on the fate of sulfur compounds, nitrogen compounds, halides, transition and heavy metals. Main synthesis gas purification technologies (based on adsorption, absorption, catalytic reactions, etc. are finally described, as well as the related challenges. Les procédés de synthèse de biocarburants par voie Fischer-Tropsch (FT, voies B-XTL, représentent des alternatives prometteuses pour la production d’énergie. Ces procédés permettent la conversion en carburants de synthèse de biomasse lignocellulosique, éventuellement mise en oeuvre en mélange avec des charges fossiles telles que petcoke, charbons ou résidus sous vide. Pour

Magnetic purification of curcumin from Curcuma longa rhizome by novel naked maghemite nanoparticles.

Science.gov (United States)

Magro, Massimiliano; Campos, Rene; Baratella, Davide; Ferreira, Maria Izabela; Bonaiuto, Emanuela; Corraducci, Vittorino; Uliana, Maíra Rodrigues; Lima, Giuseppina Pace Pereira; Santagata, Silvia; Sambo, Paolo; Vianello, Fabio

2015-01-28

Naked maghemite nanoparticles, namely, surface active maghemite nanoparticles (SAMNs), characterized by a diameter of about 10 nm, possessing peculiar colloidal stability, surface chemistry, and superparamagnetism, present fundamental requisites for the development of effective magnetic purification processes for biomolecules in complex matrices. Polyphenolic molecules presenting functionalities with different proclivities toward iron chelation were studied as probes for testing SAMN suitability for magnetic purification. Thus, the binding efficiency and reversibility on SAMNs of phenolic compounds of interest in the pharmaceutical and food industries, namely, catechin, tyrosine, hydroxytyrosine, ferulic acid, coumaric acid, rosmarinic acid, naringenin, curcumin, and cyanidin-3-glucoside, were evaluated. Curcumin emerged as an elective compound, suitable for magnetic purification by SAMNs from complex matrices. A combination of curcumin, demethoxycurcumin, and bis-demethoxycurcumin was recovered by a single magnetic purification step from extracts of Curcuma longa rhizomes, with a purity >98% and a purification yield of 45%, curcumin being >80% of the total purified curcuminoids.

A scintillator purification system for the Borexino solar neutrino detector

Science.gov (United States)

Benziger, J.; Cadonati, L.; Calaprice, F.; Chen, M.; Corsi, A.; Dalnoki-Veress, F.; Fernholz, R.; Ford, R.; Galbiati, C.; Goretti, A.; Harding, E.; Ianni, Aldo; Ianni, Andrea; Kidner, S.; Leung, M.; Loeser, F.; McCarty, K.; McKinsey, D.; Nelson, A.; Pocar, A.; Salvo, C.; Schimizzi, D.; Shutt, T.; Sonnenschein, A.

2008-03-01

Purification of the 278 tons of liquid scintillator and 889 tons of buffer shielding for the Borexino solar neutrino detector is performed with a system that combines distillation, water extraction, gas stripping, and filtration. This paper describes the principles of operation, design, and construction of that purification system, and reviews the requirements and methods to achieve system cleanliness and leak-tightness.

Recovery of valuable products from the raffinate of uranium and thorium pilot-plant

International Nuclear Information System (INIS)

Martins, E.A.J.

1990-01-01

IPEN-CNEN/SP has being very active in refining yellow cake to pure ammonium diuranate which is converted to uranium trioxide, uranium dioxide, uranium tetra-and hexa-fluoride in sequential way. The technology of the thorium purification and its conversion to nuclear grade products has been a practice since several years as well. For both elements the major waste to be worked is the raffinate from purification via TBP-varsol in pulsed columns. In this paper the actual processing technology is reviewed with special emphasis on the recovery of valuable products, mainly nitric acid, ammonium nitrate, uranium, thorium and rare earth elements. Ammonium nitrate from the precipitation of uranium diuranate is of good quality, being radioactivity and uranium-free, and recommended to be applied as fertilizer. In conclusion the main effort is to maximize the recycle and reuse of the above mentioned chemicals. (author)

Study of air purification in the production of radioactive compounds

International Nuclear Information System (INIS)

Fradin, J.; Desroches, J.

1958-12-01

As the fabrication of radio-elements takes place in almost airtight enclosures in which a frequent air renewal is required, and while taking the purification rate into account (1.000 to 5.000 m 3 /h), the authors report the study of wet purification in conjunction with dry purification through paper filters, in order to capture dusts. An apparatus has been implemented which allows high gas flow rates. A radioactive aerosol has been introduced in this apparatus and its efficiency has been measured by different means. The authors describe the instrumentation (column, aerosol generator), operation, rate adjustment, and losses. Aerosols of manganese and sodium have been used. Their particle granulometry has been determined. The authors report several types of tests [fr

Rational and systematic protein purification process development: the next generation.

Science.gov (United States)

Nfor, Beckley K; Verhaert, Peter D E M; van der Wielen, Luuk A M; Hubbuch, Jürgen; Ottens, Marcel

2009-12-01

Current biopharmaceutical manufacturing strongly relies on using purification platform processes, offering harmonization of practices and speed-to-market. However, the ability of such processes to respond quickly to anticipated higher quality and capacity demands is under question. Here, we describe novel approaches for purification process development that incorporate biothermodynamics, modern high throughput experimentation and simulation tools. Such development leads to production platform-specific databases containing thermodynamic protein descriptors of major host cell proteins over a range of experimental conditions. This will pave the way for in silico purification process development, providing better process understanding and the potential to respond quickly to product quality and market demands. Future efforts will focus on improving this field further and enabling more rationale in process development.

Water Purification Product

Science.gov (United States)

2004-01-01

Ecomaster, an affiliate of BioServe Space Technologies, this PentaPure technology has been used to purify water for our nation's Space Shuttle missions since 1981. WTC-Ecomaster of Mirneapolis, Minnesota manufactures water purification systems under the brand name PentaPure (TM). BioServe researcher Dr. George Marchin, of Kansas State University, first demonstrated the superiority of this technology and licensed it to WTC. Marchin continues to perform microgravity research in the development of new technologies for the benefit of life on Earth.

The Purification of a Blood Group A Glycoprotein: An Affinity Chromatography Experiment.

Science.gov (United States)

Estelrich, J.; Pouplana, R.

1988-01-01

Describes a purification process through affinity chromatography necessary to obtain specific blood group glycoproteins from erythrocytic membranes. Discusses the preparation of erythrocytic membranes, extraction of glycoprotein from membranes, affinity chromatography purification, determination of glycoproteins, and results. (CW)

Performance of photocatalyst based carbon nanodots from waste frying oil in water purification

International Nuclear Information System (INIS)

Aji, Mahardika Prasetya; Wiguna, Pradita Ajeng; Susanto,; Rosita, Nita; Suciningtyas, Siti Aisyah; Sulhadi

2016-01-01

Carbon Nanodots (C-Dots) from waste frying oil could be used as a photocatalyst in water purification with solar light irradiation. Performance of C-Dots as a photocatalyst was tested in the process of water purification with a given synthetic sewage methylene blue. The tested was also conducted by comparing the performance C-Dots made from frying oil, waste fryng oil as a photocatalyst and solution of methylene blue without photocatalyst C-Dots. Performance of C-Dots from waste frying oil were estimated by the results of absorbance spectrum. The results of measurement absorbance spectrum from the process of water purification with photocatalyst C-Dots showed that the highest intensity at a wavelength 664 nm of methylene blue decreased. The test results showed that the performance of photocatalyst C-Dots from waste frying oil was better in water purification. This estimated that number of particles C-dots is more in waste frying oil because have experieced repeated the heating process so that the higher particles concentration make the photocatalyst process more effective. The observation of the performance C-Dots from waste frying oil as a photocatalyst in the water purification processes become important invention for solving the problems of waste and water purification.

Performance of photocatalyst based carbon nanodots from waste frying oil in water purification

Energy Technology Data Exchange (ETDEWEB)

Aji, Mahardika Prasetya, E-mail: mahardika190@gmail.com; Wiguna, Pradita Ajeng; Susanto,; Rosita, Nita; Suciningtyas, Siti Aisyah; Sulhadi [Department of Physics, Faculty of Mathematics and Natural Science Universitas Negeri Semarang, Jalan Raya Sekaran Gunungpati 50229 Indonesia (Indonesia)

2016-04-19

Carbon Nanodots (C-Dots) from waste frying oil could be used as a photocatalyst in water purification with solar light irradiation. Performance of C-Dots as a photocatalyst was tested in the process of water purification with a given synthetic sewage methylene blue. The tested was also conducted by comparing the performance C-Dots made from frying oil, waste fryng oil as a photocatalyst and solution of methylene blue without photocatalyst C-Dots. Performance of C-Dots from waste frying oil were estimated by the results of absorbance spectrum. The results of measurement absorbance spectrum from the process of water purification with photocatalyst C-Dots showed that the highest intensity at a wavelength 664 nm of methylene blue decreased. The test results showed that the performance of photocatalyst C-Dots from waste frying oil was better in water purification. This estimated that number of particles C-dots is more in waste frying oil because have experieced repeated the heating process so that the higher particles concentration make the photocatalyst process more effective. The observation of the performance C-Dots from waste frying oil as a photocatalyst in the water purification processes become important invention for solving the problems of waste and water purification.

Breathing Air Purification for Hyperbaric Purposes, Part II

Directory of Open Access Journals (Sweden)

Woźniak Arkadiusz

2015-03-01

Full Text Available Determining the efficiency of breathing air purification for hyperbaric purposes with the use of filtration systems is of a crucial importance. However, when the Polish Navy took samples of breathing air from their own filtration plant for quality purposes, these were found to not meet the required standard. The identification of this problem imposed the need to undertake actions aimed at the elimination of the identified disruptions in the process of breathing air production, with the objective of assuring its proper quality. This study presents the results of the initial tests on the air supply sources utilised by the Polish Navy, which were carried out for the purpose of setting a proper direction of future works and implementing corrective measures in order to optimise the breathing air production process. The obtained test results will be used in a subsequent publication devoted to the assessment of the level of efficiency of air purification with the use of a multifaceted approach consisting in the utilisation of various types of air supply sources and different configurations of purification systems.

The effect of water purification systems on fluoride content of drinking water

Directory of Open Access Journals (Sweden)

Prabhakar A

2008-03-01

Full Text Available Objective: The purpose of the present study was to determine the effect of different water purification systems on the fluoride content of drinking water and to compare the efficacy of these water purification systems in reducing the fluoride content. Materials and Methods: Five different water purification systems were tested in this study. They were reverse osmosis, distillation, activated carbon, Reviva ® , and candle filter. The water samples in the study were of two types, viz, borewell water and tap water, these being commonly used by the people of Davangere City, Karnataka. The samples were collected before and after purification, and fluoride analysis was done using fluoride ion-specific electrode. Results: The results showed that the systems based on reverse osmosis, viz, reverse osmosis system and Reviva ® showed maximum reduction in fluoride levels, the former proving to be more effective than the latter; followed by distillation and the activated carbon system, with the least reduction being brought about by candle filter. The amount of fluoride removed by the purification system varied between the system and from one source of water to the other. Interpretation and Conclusion: Considering the beneficial effects of fluoride on caries prevention; when drinking water is subjected to water purification systems that reduce fluoride significantly below the optimal level, fluoride supplementation may be necessary. The efficacy of systems based on reverse osmosis in reducing the fluoride content of water indicates their potential for use as defluoridation devices.

Intense pyrification of volatile inorganic halides

International Nuclear Information System (INIS)

Nesel'son, L.A.; Tret'yakov, K.V.; Cherenkov, A.V.; Solov'ev, V.F.

1992-01-01

It is found that the studies systems form the fusibility curves of eutectic type with the limited regions of separation in the middle part of composition. The liquid-vapour equilibrium of the WF 6 -Nb(Ta)F 5 systems is characterized by strong positive deviation from the ideal case but without formation of azeotropes. The values of coefficients for relative volatility of the dilute solutions of niobium and tantalum pentafluorides in tungsten hexafluoride are found. The values of these coefficients are sufficiently large to provide the efficient purification from niobium and tantalum by the method of fractional distillation

Moderator purification and design modifications based on operation feedback

International Nuclear Information System (INIS)

Das, S.; Chakrabarti, A.K.; Shirolkar, K.M.; Sharma, V.K.

1994-01-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author)

Immunoaffinity purification and reconstitution of the human bilirubin/phenol UDP-glucuronosyltransferase family

NARCIS (Netherlands)

Seppen, J.; Jansen, P. L.; Oude Elferink, R. P.

1995-01-01

When membrane proteins are solubilized and subjected to purification procedures, the loss of lipids surrounding the protein often results in irreversible inactivation. We describe a procedure for the immunoaffinity purification of the membrane protein UDP-glucuronosyltransferase from human liver.

IMMUNOAFFINITY PURIFICATION AND RECONSTITUTION OF THE HUMAN BILIRUBIN PHENOL UDP-GLUCURONOSYLTRANSFERASE FAMILY

NARCIS (Netherlands)

SEPPEN, J; JANSEN, PLM; ELFERINK, RPJO

When membrane proteins are solubilized and subjected to purification procedures, the loss of lipids surrounding the protein often results in irreversible inactivation. We describe a procedure for the immunoaffinity purification of the membrane protein UDP-glucuronosyltransferase from human liver.

Technical note: A simple back-mounted harness for grazing dairy cows to facilitate the sulfur hexafluoride tracer gas technique.

Science.gov (United States)

van Wyngaard, Josef D V; Meeske, Robin; Erasmus, Lourens J

2018-03-01

We describe here a cattle harness to attach a gas collection vessel to facilitate the sulfur hexafluoride (SF 6 ) tracer gas technique. The harness consists of 2 major components: (1) a lightweight, robust body fabricated from an equine surcingle or lunge roller with padded thoracic trapezius pressure points, a bespoke shaping shaft for spine support, and adjustable buckles on both sides; and (2) an elastic flank-strap to prevent the harness from dislodging. The spine support consists of stainless steel laminated with carbon fiber. This support minimizes the contact area with the animal's skin, relieves the spine area of pressure, and creates free flow of ambient air below the platform, reducing sweat accumulation and hence preventing skin lesions. The harness weighs approximately 1.2 kg, allows for attachment of 2 gas collection vessels (animal and background sample), and is cost effective. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The MIMIC Method with Scale Purification for Detecting Differential Item Functioning

Science.gov (United States)

Wang, Wen-Chung; Shih, Ching-Lin; Yang, Chih-Chien

2009-01-01

This study implements a scale purification procedure onto the standard MIMIC method for differential item functioning (DIF) detection and assesses its performance through a series of simulations. It is found that the MIMIC method with scale purification (denoted as M-SP) outperforms the standard MIMIC method (denoted as M-ST) in controlling…

Purification of a synthetic pterocarpanquinone by countercurrent chromatography

International Nuclear Information System (INIS)

Costa, Fernanda das Neves; Silva, Alcides Jose M. da; Domingos, Jorge L. de Oliveira; Costa, Paulo Roberto R.; Leitao, Gilda G.; Daher Netto, Chaquip

2012-01-01

Countercurrent chromatography (CCC) was employed as a useful, fast and economic alternative to conventional chromatography techniques for the purification of a synthetic pterocarpanquinone, LQB-118. The separation was performed in a two-step CCC with the solvent system hexanechloroform- methanol-water 2:1.5:5:2 in both steps. Traditional purification of these reaction products by silica gel column chromatography demanded a large amount of solvent and time, besides allowing the irreversible adsorption of the compound in the column. The use of 1 H NMR for the calculation of KD of target compound is proposed as an alternative for HPLC measurements. (author)

Purification and Characterization of Thermostable Cellulase from ...

African Journals Online (AJOL)

Available online at http://www.tjpr.org ... Methods: Molecular community structure of the newly selected thermophilic bacterial ... Keywords: Thermostable cellulase, Sugarcane bagasse, Purification, Characterization, Hot spring ... Currently, one.

Penetration of sulfur hexafluoride into cellular polypropylene films and its effect on the electric charging and electromechanical response of ferroelectrets

International Nuclear Information System (INIS)

Qiu Xunlin; Wegener, Michael; Wirges, Werner; Zhang Xiaoqing; Hillenbrand, Joachim; Xia Zhongfu; Gerhard-Multhaupt, Reimund; Sessler, Gerhard M

2005-01-01

Cellular polypropylene (PP) films were treated with sulfur hexafluoride (SF 6 ) gas in order to study the SF 6 penetration behaviour and optimize the electric charging conditions. There were differences in the penetration of SF 6 for different cellular PP materials, depending on the microscopic properties, which manifest themselves in the voided structure as well as in the mechanical stiffnesses of the cellular films. The penetration of SF 6 after long-term pressure treatment is confirmed in strongly inflated cellular PP films with a low mechanical stiffness of about 1 MPa. No SF 6 penetration occurs for slightly inflated cellular PP films with smaller void sizes and higher mechanical stiffnesses of around 5.8 MPa. The observed thickness variations, the higher charging fields during corona charging because of SF 6 penetration and the SF 6 environment, as well as the resulting electromechanical properties are discussed

HGSYSTEMUF6, Simulating Dispersion Due to Atmospheric Release of Uranium Hexafluoride (UF6)

International Nuclear Information System (INIS)

Hanna, G; Chang, J.C.; Zhang, J.X.; Bloom, S.G.; Goode, W.D. Jr; Lombardi, D.A.; Yambert, M.W.

2001-01-01

1 - Description of program or function: HGSYSTEMUF6 is a suite of models designed for use in estimating consequences associated with accidental, atmospheric release of Uranium Hexafluoride (UF 6 ) and its reaction products, namely Hydrogen Fluoride (HF), and other non-reactive contaminants which are either negatively, neutrally, or positively buoyant. It is based on HGSYSTEM Version 3.0 of Shell Research LTD., and contains specific algorithms for the treatment of UF 6 chemistry and thermodynamics. HGSYSTEMUF6 contains algorithms for the treatment of dense gases, dry and wet deposition, effects due to the presence of buildings (canyon and wake), plume lift-off, and the effects of complex terrain. The models components of the suite include (1) AEROPLUME/RK, used to model near-field dispersion from pressurized two-phase jet releases of UF6 and its reaction products, (2) HEGADAS/UF6 for simulating dense, ground based release of UF 6 , (3) PGPLUME for simulation of passive, neutrally buoyant plumes (4) UF6Mixer for modeling warm, potentially reactive, ground-level releases of UF 6 from buildings, and (5) WAKE, used to model elevated and ground-level releases into building wake cavities of non-reactive plumes that are either neutrally or positively buoyant. 2 - Methods: The atmospheric release and transport of UF 6 is a complicated process involving the interaction between dispersion, chemical and thermodynamic processes. This process is characterized by four separate stages (flash, sublimation, chemical reaction entrainment and passive dispersion) in which one or more of these processes dominate. The various models contained in the suite are applicable to one or more of these stages. For example, for modeling reactive, multiphase releases of UF 6 , the AEROPLUME/RK component employs a process-splitting scheme which numerically integrates the differential equations governing dispersion, UF 6 chemistry, and thermodynamics. This algorithm is based on the assumption that

Moderator purification and design modifications based on operation feedback

Energy Technology Data Exchange (ETDEWEB)

Das, S; Chakrabarti, A K; Shirolkar, K M; Sharma, V K [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author). 2 refs., 3 figs., 1 tab.

Operating experiences of gas purification system of Heavy Water Plant Talcher (Paper No. 1.11)

International Nuclear Information System (INIS)

Bhattacharya, R.; Mohanty, P.R.; Pandey, B.L.

1992-01-01

The operating experiences with the purification system installed at Heavy Water Plant, Talcher for purification of feed synthesis gas from fertilizer plant is described. The purification system has performed satisfactorily even with levels of impurities as much as 15 to 20 ppm of oxygen and carbon monoxide. The system could not however be tested at designed gas throughput and on a sustained basis. However, increase in gas throughput upto the design value is not expected to pose any problem on the performance of the purification system. (author). 5 figs

Purification

DEFF Research Database (Denmark)

Andersen, Astrid Oberborbeck

2017-01-01

In Arequipa, Peru’s second largest city, engineers work hard to control water flows and provide different sectors with clean and sufficient water. In 2011, only 10 percent of the totality of water used daily by Arequipa’s then close to 1 million people—in households, tourism, industry, and mining......—was treated before it was returned to the river where it continues its flow downstream towards cultivated fields and, finally, into the Pacific Ocean. It takes specialized knowledge and manifold technologies to manage water and sustain life in Arequipa, and engineers are central actors for making water flow...... of categories can be understood as practices of purification. However, a purely technical grip on water is never possible. Unruly elements, like weather, contamination, urban dwellers, and competing interests, interfere and make processes of intervention unstable. Water is never completely cleaned, and, equally...

An analysis of main factors in electron beam flue gas purification

International Nuclear Information System (INIS)

Zhang Ming; Xu Guang

2003-01-01

Electron beam flue gas purification method is developing very quickly in recent years. Based on the experiment setting for electron beam flue gas purification in Institute of Nuclear Energy and Technology, Tsinghua University, how the technique factors affect the ratio of desulphurization and denitrogenation are described. Radiation dose (D), temperature (T), humidity (H), pour ammonia quantity (α) and initial concentration of SO 2 (C SO 2 ) and NO x (C NO x ) are main factors influencing flue gas purification. Using the methods of correlation analysis and regression analysis, the primary effect factors are found out and the regression equations are set to optimize the system process, predigest the system structure and to forecast the experimental results. (authors)

Effectiveness of liquid radioactive waste purification by inorganic granulated sorbents

International Nuclear Information System (INIS)

Komarevskij, V.M.; Stepanets, O.V.; Sharygin, L.M.; Matveev, S.A.

1995-01-01

Study results on purification of simulative and real liquid radioactive wastes from fission products radionuclides and by inorganic corrosion-nature sorbents 'Thermoxide' are presented. Properties by sorption of cesium, strontium and cobalt are studied; results of experiments on purification of weakly-salted water solutions (waste waters, ships drainage tanks, showers and laundries) of the Beloyarsk NPP are presented. Sorbents source characteristics are determined. 4 refs., 2 figs., 3 tabs

Purification, characterization of phytase enzyme from Lactobacillus ...

African Journals Online (AJOL)

SAM

2014-06-04

Jun 4, 2014 ... 2Department of Food Technology, Erzurum Vocational Training School, Ataturk University, 25240, ... facultative anaerobic, catalase-negative, immobile (with ..... Partial purification of phytase from a soil isolate bacterium,.

Sandia Sodium Purification Loop (SNAPL) description and operations manual

International Nuclear Information System (INIS)

Acton, R.U.; Weatherbee, R.L.; Smith, L.A.; Mastin, F.L.; Nowotny, K.E.

1985-08-01

Sandia's Sodium Purification Loop was constructed to purify sodium for fast reactor safety experiments. An oxide impurity of less than 10 parts per million is required by these in-pile experiments. Commercial, reactor grade sodium is purchased in 180 kg drums. The sodium is melted and transferred into the unit. The unit is of a loop design and purification is accomplished by ''cold trapping.'' Sodium purified in this loop has been chemically analysed at one part per million oxygen by weight. 5 refs., 22 figs., 7 tabs

HOUSEHOLD PURIFICATION OF FLUORIDE CONTAMINATED MAGADI (TRONA)

DEFF Research Database (Denmark)

Nielsen, Joan Maj; Dahi, Elian

1997-01-01

Purification of fluoride contaminated magadi is studied using bone char sorption and calcium precipitation. The bone char treatment is found to be workable both in columns and in batches where the magadi is dissolved in water prior to treatment. The concentrations in the solutions were 89 g magadi....../L and 95 and 400 mg F/L respectively in natural and synthetic solutions. The fluoride removal capacities observed were 4.6 mg F/g bone char for the column system and 2.7 mg F/g bone char for the batch system in case of synthetic magadi solution. It is however concluded that the batch system is the best...... treatment method. A procedure for purification of fluoride contaminated magadi at household level is described....

Air/Water Purification

Science.gov (United States)

1992-01-01

After 18 years of research into air/water pollution at Stennis Space Center, Dr. B. C. Wolverton formed his own company, Wolverton Environmental Services, Inc., to provide technology and consultation in air and water treatment. Common houseplants are used to absorb potentially harmful materials from bathrooms and kitchens. The plants are fertilized, air is purified, and wastewater is converted to clean water. More than 100 U.S. communities have adopted Wolverton's earlier water hyacinth and artificial marsh applications. Catfish farmers are currently evaluating the artificial marsh technology as a purification system.

Sulfur Hexafluoride 20% versus Lactated Ringer′s solution for Prevention of Early Postoperative Vitreous Hemorrhage after Diabetic Vitrectomy

Directory of Open Access Journals (Sweden)

Fereydoun Farrahi

2010-01-01

Full Text Available Purpose: To compare the hemostatic effect of sulfur hexafluoride 20% (SF6 20% with lactated Ringer′s solution for prevention of early postoperative vitreous hemorrhage following diabetic vitrectomy. Methods: In a prospective randomized clinical trial, 50 eyes undergoing diabetic vitrectomy were divided into two groups. At the conclusion of surgery, in one group the vitreous cavity was filled with SF6 20% while in the other group lactated Ringer′s solution was retained in the vitreous cavity. The two groups were compared for the rate of early postoperative vitreous hemorrhage. Results: The incidence of vitreous hemorrhage was lower in the SF6 group than the Ringer′s group 4 days (20% vs 68%, P=0.001, 7 days (24% vs 60%, P=0.01 and 4 weeks (16% vs 40%, P=0.059 after vitrectomy. Conclusion: In comparison with lactated Ringer′s solution, SF6 20% had a significant hemostatic effect especially in the early postoperative period after diabetic vitrectomy and reduced the incidence of vitreous hemorrhage.

A validation study of the intertran model for assessing risks of transportation accidents: Road transport of uranium hexafluoride

International Nuclear Information System (INIS)

Tomachevsky, E.G.; Ringot, C.; Pages, P.; Hubert, P.

1985-06-01

The INTERTRAN code was developed by the IAEA in order to provide member states with a simple and rapide method of assessing the risk involved in the transportation of radioactive materials and one which was applicable on a worldwide scale. Before being used, this code must be validated and the CEA thus compared the results obtained with the conventional risk assessment methods used by the CEPN with those derived from INTERTRAN. This paper gives the results of the studies made on the subject of road transportation of uranium hexafluoride in France. The conventional accident risk assessment method gave a figure of 8.84 x 10 -4 deaths/year, whereas INTERTRAN announces 1.78 x 10 -2 . To these figures should be added 3.38 x 10 -2 deaths/year, which is the intrinsic road risk, whatever the goods carried. In relation to conventional estimates, the INTERTRAN forecasts are five times lower for the U risk and twenty times higher for the HF risk. The chemical risk is indeed the most prevalent one in this case. Other comparisons are needed to validate this code

Standard test method for isotopic analysis of uranium hexafluoride by double standard single-collector gas mass spectrometer method

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This is a quantitative test method applicable to determining the mass percent of uranium isotopes in uranium hexafluoride (UF6) samples with 235U concentrations between 0.1 and 5.0 mass %. 1.2 This test method may be applicable for the entire range of 235U concentrations for which adequate standards are available. 1.3 This test method is for analysis by a gas magnetic sector mass spectrometer with a single collector using interpolation to determine the isotopic concentration of an unknown sample between two characterized UF6 standards. 1.4 This test method is to replace the existing test method currently published in Test Methods C761 and is used in the nuclear fuel cycle for UF6 isotopic analyses. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appro...

Secretory immunoglobulin purification from whey by chromatographic techniques.

Science.gov (United States)

Matlschweiger, Alexander; Engelmaier, Hannah; Himmler, Gottfried; Hahn, Rainer

2017-08-15

Secretory immunoglobulins (SIg) are a major fraction of the mucosal immune system and represent potential drug candidates. So far, platform technologies for their purification do not exist. SIg from animal whey was used as a model to develop a simple, efficient and potentially generic chromatographic purification process. Several chromatographic stationary phases were tested. A combination of two anion-exchange steps resulted in the highest purity. The key step was the use of a small-porous anion exchanger operated in flow-through mode. Diffusion of SIg into the resin particles was significantly hindered, while the main impurities, IgG and serum albumin, were bound. In this step, initial purity was increased from 66% to 89% with a step yield of 88%. In a second anion-exchange step using giga-porous material, SIg was captured and purified by step or linear gradient elution to obtain fractions with purities >95%. For the step gradient elution step yield of highly pure SIg was 54%. Elution of SIgA and SIgM with a linear gradient resulted in a step yield of 56% and 35%, respectively. Overall yields for both anion exchange steps were 43% for the combination of flow-through and step elution mode. Combination of flow-through and linear gradient elution mode resulted in a yield of 44% for SIgA and 39% for SIgM. The proposed process allows the purification of biologically active SIg from animal whey in preparative scale. For future applications, the process can easily be adopted for purification of recombinant secretory immunoglobulin species. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel peptide ligand with high binding capacity for antibody purification

DEFF Research Database (Denmark)

Lund, L. N.; Gustavsson, P. E.; Michael, R.

2012-01-01

Small synthetic ligands for protein purification have become increasingly interesting with the growing need for cheap chromatographic materials for protein purification and especially for the purification of monoclonal antibodies (mAbs). Today, Protein A-based chromatographic resins are the most...... commonly used capture step in mAb down stream processing; however, the use of Protein A chromatography is less attractive due to toxic ligand leakage as well as high cost. Whether used as an alternative to the Protein A chromatographic media or as a subsequent polishing step, small synthetic peptide...... ligands have an advantage over biological ligands; they are cheaper to produce, ligand leakage by enzymatic degradation is either eliminated or significantly reduced, and they can in general better withstand cleaning in place (CIP) conditions such as 0.1 M NaOH. Here, we present a novel synthetic peptide...

Nanotechnology for water treatment and purification

CERN Document Server

Apblett, Allen

2014-01-01

This book describes the latest progress in the application of nanotechnology for water treatment and purification. Leaders in the field present both the fundamental science and a comprehensive overview of the diverse range of tools and technologies that have been developed in this critical area. Expert chapters present the unique physicochemical and surface properties of nanoparticles and the advantages that these provide for engineering applications that ensure a supply of safe drinking water for our growing population. Application areas include generating fresh water from seawater, preventing contamination of the environment, and creating effective and efficient methods for remediation of polluted waters. The chapter authors are leading world-wide experts in the field with either academic or industrial experience, ensuring that this comprehensive volume presents the state-of-the-art in the integration of nanotechnology with water treatment and purification. Covers both wastewater and drinking water treatmen...

The method of purification of waste water of NPS from petroleum oil using UV-radiation

International Nuclear Information System (INIS)

Kulemin, V.V.; Kareta, V.I.

1993-01-01

The main methods of concentration and purification of radioactive waste water of russian NPS are distillation and ion exchange. When waste water containing petroleum oil and washing matter is distillated, part of petroleum and washing matters go to the condensate. The purification of this condensate leads to pollution of ion exchange resins by petroleum oil and reduction of the filter cycle number. The purification of condensate of Russian NPS from petroleum oil is carried out using active carbon and polymer filters, but this process is not effective and fails to give pure condensate. Therefore, the authors began to search for more effective methods of purification of waste water from petroleum oil. They found that UV-radiation makes it possible to purify water from petroleum matter to concentration of the organic phase less than 0.5 mg/dm3. In this process of purification the air, contained in the water phase, was used as an oxidant. When purification is carried out in the absence of sorbents, the quantity of radioactive solid waste, which have to be recovered, decreases. During the study of purification of waste water it was found that increasing of the temperature of the process increases the rate of UV-radiation-induced oxidation of organic phase. The increase in the initial concentration of petroleum products also increases the rate of petroleum oil decomposition. The content of ions in water phase decreases the purification rate. The investigations were carried out on the laboratory scale with water and condensate from Tver's NPS

Emulsion Liquid Membrane Technology in Organic Acid Purification

International Nuclear Information System (INIS)

Norela Jusoh; Norasikin Othman; Nur Alina Nasruddin

2016-01-01

Emulsion Liquid Membrane (ELM) process have shown a great potential in wide application of industrial separations such as in removal of many chemicals, organic compounds, metal ions, pollutants and biomolecules. This system promote many advantages including simple operation, high selectivity, low energy requirement, and single stage extraction and stripping process. One potential application of ELM is in the purification of succinic acid from fermentation broth. This study outline steps for developing emulsion liquid membrane process in purification of succinic acid. The steps include liquid membrane formulation, ELM stability and ELM extraction of succinic acid. Several carrier, diluent and stripping agent was screened to find appropriate membrane formulation. After that, ELM stability was investigated to enhance the recovery of succinic acid. Finally, the performance of ELM was evaluated in the extraction process. Results show that formulated liquid membrane using Amberlite LA2 as carrier, palm oil as diluent and sodium carbonate, Na_2CO_3 as stripping agent provide good performance in purification. On the other hand, the prepared emulsion was observed to be stable up to 1 hour and sufficient for extraction process. In conclusion, ELM has high potential to purify succinic acid from fermentation broth. (author)

Doping reversed-phase media for improved peptide purification.

Science.gov (United States)

Khalaf, Rushd; Forrer, Nicola; Buffolino, Gianluca; Gétaz, David; Bernardi, Susanna; Butté, Alessandro; Morbidelli, Massimo

2015-06-05

The purification of therapeutic peptides is most often performed using one or more reversed phase chromatography steps. This ensures high purities while keeping the costs of purification under control. In this paper, a doped reversed phase chromatographic material is tested and compared to traditional reversed phase materials. The doping consists of adding limited amounts of ion exchange ligands to the surface of the material to achieve orthogonal separation and increase the non-hydrophobic interactions with the surface. These ionic groups can either be attractive (opposite charge), or repulsive (same charge) to the peptide. The benefit of this new doped reversed phase material is shown through increases in selectivity in diluted conditions and yield and productivity in overloaded (i.e. industrial) conditions. It is the conjectured that all performance characteristics should increase using repulsive doping groups, whereas these characteristics should decrease when using attractive doping groups. This conjecture is shown to be true through several examples, including purifications of industrially relevant peptide crudes, in industrially relevant conditions. Moreover, the effect of ionic strength and organic modifier concentration was explored and shown to be in line with the expected behavior. Copyright © 2015 Elsevier B.V. All rights reserved.

The modified swirl sedimentation tanks for water purification.

Science.gov (United States)

Ochowiak, Marek; Matuszak, Magdalena; Włodarczak, Sylwia; Ancukiewicz, Małgorzata; Krupińska, Andżelika

2017-03-15

This paper discusses design, evaluation, and application for the use of swirl/vortex technologies as liquid purification system. A study was performed using modified swirl sedimentation tanks. The vortex separators (OW, OWK, OWR and OWKR) have been studied under laboratory conditions at liquid flow rate from 2.8⋅10 -5 to 5.1⋅10 -4 [m 3 /s]. The pressure drop and the efficiency of purification of liquid stream were analyzed. The suspended particles of different diameters were successfully removed from liquid with the application of swirl chambers of proposed constructions. It was found that damming of liquid in the tank increases alongside liquid stream at the inlet and depends on the tank construction. The efficiency of the sedimentation tanks increases alongside the diameters of solid particles and decrease in the liquid flow rate. The best construction proved to be the OWR sedimentation tank due to smallest liquid damming, even at high flow rates, and the highest efficiency of the purification liquid stream for solid particles of the smallest diameter. The proposed solution is an alternative to the classical constructions of sedimentation tanks. Copyright © 2016 Elsevier Ltd. All rights reserved.

Purification of crude glycerol from transesterification reaction of palm oil using direct method and multistep method

Science.gov (United States)

Nasir, N. F.; Mirus, M. F.; Ismail, M.

2017-09-01

Crude glycerol which produced from transesterification reaction has limited usage if it does not undergo purification process. It also contains excess methanol, catalyst and soap. Conventionally, purification method of the crude glycerol involves high cost and complex processes. This study aimed to determine the effects of using different purification methods which are direct method (comprises of ion exchange and methanol removal steps) and multistep method (comprises of neutralization, filtration, ion exchange and methanol removal steps). Two crude glycerol samples were investigated; the self-produced sample through the transesterification process of palm oil and the sample obtained from biodiesel plant. Samples were analysed using Fourier Transform Infrared Spectroscopy, Gas Chromatography and High Performance Liquid Chromatography. The results of this study for both samples after purification have showed that the pure glycerol was successfully produced and fatty acid salts were eliminated. Also, the results indicated the absence of methanol in both samples after purification process. In short, the combination of 4 purification steps has contributed to a higher quality of glycerol. Multistep purification method gave a better result compared to the direct method as neutralization and filtration steps helped in removing most excess salt, fatty acid and catalyst.

[Development of new magnetic bead separation and purification instrument].

Science.gov (United States)

Xu, Yingyuan; Chen, Yi

2014-05-01

The article describes the development of new magnetic bead separation and purification instrument. The main application of the instrument is to capture tubercle bacillus from sputum. It is a pretreatment instrument and provides a new platform to help doctors to diagnose bacillary phthisis. Not only could it be used for tubercle bacillus capturing, but also for gene, protein and cell separating and purification. Because the controller of the instrument is 16-bit single chip microcomputer, the cost could be greatly reduced and it will be widely used in China.

Optimized Expression and Purification for High-Activity Preparations of Algal [FeFe]-Hydrogenase

Energy Technology Data Exchange (ETDEWEB)

Yacoby, I.; Tegler, L. T.; Pochekailov, S.; Zhang, S.; King, P. W.

2012-04-01

Recombinant expression and purification of metallo-enzymes, including hydrogenases, at high-yields is challenging due to complex, and enzyme specific, post-translational maturation processes. Low fidelities of maturation result in preparations containing a significant fraction of inactive, apo-protein that are not suitable for biophysical or crystallographic studies. We describe the construction, overexpression and high-yield purification of a fusion protein consisting of the algal [2Fe2S]-ferredoxin PetF (Fd) and [FeFe]-hydrogenase HydA1. The maturation of Fd-HydA1 was optimized through improvements in culture conditions and media components used for expression. We also demonstrated that fusion of Fd to the N-terminus of HydA1, in comparison to the C-terminus, led to increased expression levels that were 4-fold higher. Together, these improvements led to enhanced HydA1 activity and improved yield after purification. The strong binding-affinity of Fd for DEAE allowed for two-step purification by ion exchange and StrepTactin affinity chromatography. In addition, the incorporation of a TEV protease site in the Fd-HydA1 linker allowed for the proteolytic removal of Fd after DEAE step, and purification of HydA1 alone by StrepTactin. In combination, this process resulted in HydA1 purification yields of 5 mg L{sup -1} of culture from E. coli with specific activities of 1000 U (U = 1 {micro}mol hydrogen evolved mg{sup -1} min{sup -1}). The [FeFe]-hydrogenases are highly efficient enzymes and their catalytic sites provide model structures for synthetic efforts to develop robust hydrogen activation catalysts. In order to characterize their structure-function properties in greater detail, and to use hydrogenases for biotechnological applications, reliable methods for rapid, high-yield expression and purification are required.

Purification, Characterization and Antibacterial Mechanism of ...

African Journals Online (AJOL)

Purpose: To carry out the extraction, purification and biological characterization, and assess the antibacterial activity of bacteriocin from Lactobacillus acidophilus XH1. Methods: Chloroform extraction method was used for bacteriocin extraction while characterization of bacteriocin was carried out by flat-dug well agar ...

Automated genomic DNA purification options in agricultural applications using MagneSil paramagnetic particles

Science.gov (United States)

Bitner, Rex M.; Koller, Susan C.

2002-06-01

The automated high throughput purification of genomic DNA form plant materials can be performed using MagneSil paramagnetic particles on the Beckman-Coulter FX, BioMek 2000, and the Tecan Genesis robot. Similar automated methods are available for DNA purifications from animal blood. These methods eliminate organic extractions, lengthy incubations and cumbersome filter plates. The DNA is suitable for applications such as PCR and RAPD analysis. Methods are described for processing traditionally difficult samples such as those containing large amounts of polyphenolics or oils, while still maintaining a high level of DNA purity. The robotic protocols have ben optimized for agricultural applications such as marker assisted breeding, seed-quality testing, and SNP discovery and scoring. In addition to high yield purification of DNA from plant samples or animal blood, the use of Promega's DNA-IQ purification system is also described. This method allows for the purification of a narrow range of DNA regardless of the amount of additional DNA that is present in the initial sample. This simultaneous Isolation and Quantification of DNA allows the DNA to be used directly in applications such as PCR, SNP analysis, and RAPD, without the need for separate quantitation of the DNA.

Purification of Microbially Expressed Recombinant Proteins via a Dual ELP Split Intein System.

Science.gov (United States)

Shi, Changhua; Han, Tzu-Chiang; Wood, David W

2017-01-01

Fusions of elastin-like peptide (ELP) purification tags and self-cleaving inteins provide a powerful platform for purifying tagless recombinant proteins without the need for conventional packed-bed columns. A drawback to this method has been premature cleaving of the ELP tag during expression, before the purification procedure can take place. Here we demonstrate a split-intein method, where the self-cleaving intein is divided into two inactive segments during expression and purification. Spontaneous assembly of the purified intein segments then restores self-cleaving activity to deliver the tagless target protein.

Standard test method for gamma energy emission from fission products in uranium hexafluoride and uranyl nitrate solution

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This test method covers the measurement of gamma energy emitted from fission products in uranium hexafluoride (UF6) and uranyl nitrate solution. It is intended to provide a method for demonstrating compliance with UF6 specifications C 787 and C 996 and uranyl nitrate specification C 788. 1.2 The lower limit of detection is 5000 MeV Bq/kg (MeV/kg per second) of uranium and is the square root of the sum of the squares of the individual reporting limits of the nuclides to be measured. The limit of detection was determined on a pure, aged natural uranium (ANU) solution. The value is dependent upon detector efficiency and background. 1.3 The nuclides to be measured are106Ru/ 106Rh, 103Ru,137Cs, 144Ce, 144Pr, 141Ce, 95Zr, 95Nb, and 125Sb. Other gamma energy-emitting fission nuclides present in the spectrum at detectable levels should be identified and quantified as required by the data quality objectives. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its us...

Affinity purification of recombinant human plasminogen activator ...

African Journals Online (AJOL)

Affinity purification of recombinant human plasminogen activator from ... Screening antibody was performed using rhPA milk in an ELISA-elution assay. ... useful for purifying other tPA mutants or other novel recombinant milkderived proteins.

Production and purification of polyclonal anti-hamster ...

African Journals Online (AJOL)

. ... IgG showed high titer and high specificity in the designed ELISA. Purified antibody and its conjugation with HRP are used in research and diagnosis of hamster disease. Key words: Production, purification, hamster immunoglobulins.

Development of partitioning process: purification of DIDPA

Energy Technology Data Exchange (ETDEWEB)

Watanabe, Masayuki; Morita, Yasuji; Kubota, Masumitsu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-04-01

The partitioning process has developed and demonstrated that the solvent extraction with diisodecylphosphoric acid (DIDPA) can successfully separate transuranium elements from a high-level liquid waste. In the solvent extraction, DIDPA is decomposed by radiolysis and hydrolysis. The main degradation product is monoisodecyl phosphoric acid (MIDPA). Ethylene glycol has been used for removing the product by a solvent extraction method. However this method has two drawbacks that two phases separate slowly and the used ethylene glycol is not regeneratable. First it was found that the addition of acetone or methanol with 20 volume % improved the phase separation. Then a new purification method was developed by using an aqueous solution of methanol or acetone. The new purification method is as excellent as the ethylene glycol method for the removal of MIDPA. (author)

Using of Mineral Recourses for Water Purification

International Nuclear Information System (INIS)

Tumanova, I.V.; Nazarenko, O.B.; Anna, Yu.

2009-01-01

Pollution of surface waters results in necessity of underground waters using for drinking. Underground waters are characterized by the high quantity of heavy metals salts. This led to development of methods reducing the concentration of the metal salts in water. Wide spread occurrence, cheapness and high sorption properties of nature minerals allow to consider them as perspective sorbents for different impurities extraction, including dissoluble compounds of heavy metals. Reachable purification efficiency with mineral resources use for the moment satisfies sanitary indexes and standards presenting to portable water in Russia. In given material there are presented the results of research of artificial sorbent and certain minerals sorption characteristics, which are typical for West Siberia. For purification quality improvement from Fe and Mn ions there are suggested to use the method of boiling bed.

Dual-purpose power plants, experiences with exhaust gas purification plants

International Nuclear Information System (INIS)

Dietrich, R.

1993-01-01

From 1984 to 1988, the research and development project ''pollutant reduction for exhaust gases from heat production systems'' sponsored by the Federal Ministry of Research and Technology (BMFT) has been carried out by TUeV in Bavaria. This project was to show the state of exhaust gas technology for small and medium-sized plants (boilers and motoric heat generators). When publishing the final report, no positive balance could be given. Based on the results, the succession project ''Exhaust gas purification plants in field test'' (ARIF) has been started. This project has the following objectives: -Measuring technical investigation of the exhaust gas purification of motoric driven heat generator systems in field test. - Suitability of hand measuring devices for emissions for a discontinuous control of the exhaust gas purification plat by the operator. - Control of new methods regarding pollutant reduction for motoric and conventional heat generators. (orig.) [de

Soft-Bake Purification of SWCNTs Produced by Pulsed Laser Vaporization

Science.gov (United States)

Yowell, Leonard; Nikolaev, Pavel; Gorelik, Olga; Allada, Rama Kumar; Sosa, Edward; Arepalli, Sivaram

2013-01-01

The "soft-bake" method is a simple and reliable initial purification step first proposed by researchers at Rice University for single-walled carbon nanotubes (SWCNT) produced by high-pressure carbon mon oxide disproportionation (HiPco). Soft-baking consists of annealing as-produced (raw) SWCNT, at low temperatures in humid air, in order to degrade the heavy graphitic shells that surround metal particle impurities. Once these shells are cracked open by the expansion and slow oxidation of the metal particles, the metal impurities can be digested through treatment with hydrochloric acid. The soft-baking of SWCNT produced by pulsed-laser vaporization (PLV) is not straightforward, because the larger average SWCNT diameters (.1.4 nm) and heavier graphitic shells surrounding metal particles call for increased temperatures during soft-bake. A part of the technology development focused on optimizing the temperature so that effective cracking of the graphitic shells is balanced with maintaining a reasonable yield, which was a critical aspect of this study. Once the ideal temperature was determined, a number of samples of raw SWCNT were purified using the soft-bake method. An important benefit to this process is the reduced time and effort required for soft-bake versus the standard purification route for SWCNT. The total time spent purifying samples by soft-bake is one week per batch, which equates to a factor of three reduction in the time required for purification as compared to the standard acid purification method. Reduction of the number of steps also appears to be an important factor in improving reproducibility of yield and purity of SWCNT, as small deviations are likely to get amplified over the course of a complicated multi-step purification process.

INVESTIGATIONS ON BIOCHEMICAL PURIFICATION OF GROUND WATER FROM HYDROGEN SULFIDE

Directory of Open Access Journals (Sweden)

Yu. P. Sedlukho

2015-01-01

Full Text Available The paper considers problems and features of biochemical removal of hydrogen sulfide from ground water. The analysis of existing methods for purification of ground water from hydrogen sulfide has been given in the paper. The paper has established shortcomings of physical and chemical purification of ground water. While using aeration methods for removal of hydrogen sulfide formation of colloidal sulfur that gives muddiness and opalescence to water occurs due to partial chemical air oxidation. In addition to this violation of sulfide-carbonate equilibrium taking place in the process of aeration due to desorption of H2S and CO2, often leads to clogging of degasifier nozzles with formed CaCO3 that causes serious operational problems. Chemical methods require relatively large flow of complex reagent facilities, storage facilities and transportation costs.In terms of hydrogen sulfide ground water purification the greatest interest is given to the biochemical method. Factors deterring widespread application of the biochemical method is its insufficient previous investigation and necessity to execute special research in order to determine optimal process parameters while purifying groundwater of a particular water supply source. Biochemical methods for oxidation of sulfur compounds are based on natural biological processes that ensure natural sulfur cycle. S. Vinogradsky has established a two-stage mechanism for oxidation of hydrogen sulfide with sulfur bacteria (Beggiatoa. The first stage presupposes oxidation of hydrogen sulphide to elemental sulfur which is accumulating in the cytoplasm in the form of globules. During the second stage sulfur bacteria begin to oxidize intracellular sulfur to sulfuric acid due to shortage of hydrogen sulfide.The paper provides the results of technological tests of large-scale pilot plants for biochemical purification of groundwater from hydrogen sulfide in semi-industrial conditions. Dependences of water quality

Acute toxicity of the hydrolysis products of uranium hexafluoride (UF6) when inhaled by the rat and guinea pig. Final report

International Nuclear Information System (INIS)

Leach, L.J.; Gelein, R.M.; Panner, B.J.; Yulie, C.L.; Cox, C.C.; Balys, M.M.; Rolchigo, P.M.

1984-04-01

This report presents the experimental animal data base from which human health consequences may be predicted from exposures mimicing accidental discharges of uranium hexafluoride (UF 6 ) in the uranium industry. Rats or guinea pigs were exposed for two, five, or ten minutes duration to air having 0.44 g U/m 3 + 0.16 g HF/m 3 to 276.67 g U/m 3 + 94.07 g HF/m 3 . Survivors of each exposure were observed for 14 days for signs of U or HF intoxication. Selected animals were necropsied and samples of major organs were studied histopathologically. When enriched UF 6 (94 percent 235 U) was used, the urine and feces from each animal were measured daily for U content. Selected samples of urine were bioassayed in order to trace the course of renal injury during the two week postexposure period. 28 references, 51 figures, 23 tables

Uranium hexafluoride - chemistry and technology of a raw material of the nuclear fuel cycle

International Nuclear Information System (INIS)

Bacher, W.; Jacob, E.

1986-01-01

Uranium hexafluoride exhibits an unusual combination of properties: UF 6 is both a large-scale industrial product, and also one of the most reactive compounds known. Its industrial application arises from the need to use enriched uranium with up to 4% 235 U as fuel in light water reactors. Enrichment is performed in isotope separation plants with UF 6 as the working gas. Its volatility and thermal stability make UF 6 suitable for this application. UF 6 handling is difficult because of its high reactivity and its radioactivity, and special experience and equipment are required which are not commonly available in laboratories or industrial facilities. The chemical reactions of UF 6 are characterized by its marked fluorination efficiency which is similar to that of F 2 . Of special importance in connection with the handling of UF 6 is its extreme sensitivity to hydrolysis. Because they all use UF 6 , the isotope separation processes currently in use (gas diffusion, gas centrifuge, separation nozzle process) have a number of common features. For instance, they are all beset by the problem of formation of solid UF 6 decomposition products, e.g. by radiolysis of UF 6 molecules induced by its own radiation. Reconversion of UF 6 into UO 2 is achieved by three well-known methods (ADU, AUC, IDP-process). To produce uranium metal, UF 6 is first reduced to UF 4 , which is subsequently reduced by Ca 6 or Mg metal. 158 refs

Influence of the drying method in chitosans purification step

International Nuclear Information System (INIS)

Fonseca, Ana C.M.; Batista, Jorge G.S.; Bettega, Antonio; Lima, Nelson B. de

2015-01-01

Currently, the study of extracellular biopolymers properties has received prominence for being easy extraction and purification. Chitosan has been an attractive proposition for applications in various fields such as engineering, biotechnology, medicine and pharmacology. For such applications, it is necessary purification of chitosan to obtain a product more concentrated and free of undesirable impurities. However, at this stage of the process of obtaining the biopolymer may occur morphological and physicochemical changes. This study evaluated the influence of the drying process after purification of a commercial chitosan sample and the importance of this step and its cost/benefit in applications requiring a high degree of purity. The method of drying influenced in the organoleptic properties and in the main characteristics of material. Analysis of the crystal structure by X-ray diffraction showed that the degree of crystallinity, X (%), in the purified chitosan samples was lower when compared with the unpurified sample. The degree of acetylation, DA (%), was analyzed by spectroscopy infrared with no significant changes on the three drying methods assessed, unlike the viscosimetric molecular weight, M_v, determined by capillary viscometry. (author)

Investigation of Various LiCl Waste Salt Purification Technologies

International Nuclear Information System (INIS)

Yung-Zun Cho; Hee-Chul Yang; Han-Soo Lee; In-Tae Kim

2008-01-01

Various purification research of LiCl waste molten salt generated from electroreduction process were tested. The purification of the LiCl waste salt very important in a various aspects, where the purification means separation of cesium and strontium form LiCl salt melts. In this study, for the separation of cesium and strontium from LiCl salt melts, precipitant agent addition techniques such as sulfate and carbonate addition method and, as a new attempt, zone freezing technique for concentration of cesium and strontium elements was investigated. As a results of this research, only strontium was carbonated by reaction with Li 2 CO 3 (cesium did not react with Li 2 CO 3 ). In case of sulfate addition method, both cesium and strontium were converted into their sulfate that is Cs 2 S 2 O 6 and SrSO 4 and maximum sulfate efficiency of cesium and strontium were about 72% and 95%, respectively. Cesium and strontium involved in LiCl molten salt could be concentrated in the molten salt by using zone freezing method. (authors)

A low inventory adsorptive process for tritium extraction and purification

International Nuclear Information System (INIS)

Keefer, B.; Bora, B.; Chew, M.; Rump, M.; Kveton, O.K.

1990-08-01

The fuel cycles of future fusion power systems present a diverse spectrum of challenges to gas separation technology, for extraction, concentration, purification and confinement of tritium in fusion fuel cycles. Economic and safety factors motivate process design for minimum tritium inventory, functional simplicity, and overall reliability. A new gas separation process with some features of interest to fusion has been demonstrated under the auspices of the Canadian Fusion Fuels Technology Project. This process (Thermally Coupled Pressure Swing Adsorption or 'TCPSA') is potentially applicable to several fusion applications for separation purification of hydrogen, notably for tritium extraction from breeder blanket purge helium. Recent experimental tests have been directed toward fusion applications, primarily extraction and concentration of tritium-rich hydrogen from the blanket purge helium stream, and also considering purification of this and other hydrogen isotope streams such as the plasma exhaust. For example, hydrogen at 0.1% concentration in helium has been extracted in a TCPSA module operating at 195 K, with the process performed in a single working space to achieve simultaneous high extraction and concentration of the hydrogen. With methane or carbon oxides as the impurities, substantially complete separation is achieved by the same apparatus at ambient temperature. Engineering projections for scale-up to ITER blanket purge extraction and purification applications indicate a low working inventory of tritium

Considerations in providing purification flows for 500 MWe PHWR primary circuits

International Nuclear Information System (INIS)

Sharma, A.K.; Goswami, S.; Bapat, C.N.; Sharma, V.K.

1995-01-01

The purpose of the purification system is to keep the primary heat transport (PHT) system clean by removing traces of impurities arising due to corrosion of the carbon steel pipes and heat transfer surfaces and erosion/corrosion of valve trims, pipes and mechanical seals or due to presence of soluble or insoluble fission products. These impurities are undesirable because they are usually radioactive, either naturally or through activation by the neutron flux as they are carried by the coolant through the reactor core. The purification system minimizes the probability of generation of radioactive impurities by controlling the chemistry of PHT coolant so that corrosion is minimum. Various considerations for providing the requisite purification flow to fulfill the above functions for a typical 500 MWe PHWR are presented. (author). 4 refs., 2 tabs., 2 figs

Decisional tool to assess current and future process robustness in an antibody purification facility.

Science.gov (United States)

Stonier, Adam; Simaria, Ana Sofia; Smith, Martin; Farid, Suzanne S

2012-07-01

Increases in cell culture titers in existing facilities have prompted efforts to identify strategies that alleviate purification bottlenecks while controlling costs. This article describes the application of a database-driven dynamic simulation tool to identify optimal purification sizing strategies and visualize their robustness to future titer increases. The tool harnessed the benefits of MySQL to capture the process, business, and risk features of multiple purification options and better manage the large datasets required for uncertainty analysis and optimization. The database was linked to a discrete-event simulation engine so as to model the dynamic features of biopharmaceutical manufacture and impact of resource constraints. For a given titer, the tool performed brute force optimization so as to identify optimal purification sizing strategies that minimized the batch material cost while maintaining the schedule. The tool was applied to industrial case studies based on a platform monoclonal antibody purification process in a multisuite clinical scale manufacturing facility. The case studies assessed the robustness of optimal strategies to batch-to-batch titer variability and extended this to assess the long-term fit of the platform process as titers increase from 1 to 10 g/L, given a range of equipment sizes available to enable scale intensification efforts. Novel visualization plots consisting of multiple Pareto frontiers with tie-lines connecting the position of optimal configurations over a given titer range were constructed. These enabled rapid identification of robust purification configurations given titer fluctuations and the facility limit that the purification suites could handle in terms of the maximum titer and hence harvest load. Copyright © 2012 American Institute of Chemical Engineers (AIChE).

Phytofilter - environmental friendly solution for purification of surface plate from urbanized territories

Science.gov (United States)

Ruchkinova, O.; Shchuckin, I.

2017-06-01

Its proved, that phytofilters are environmental friendly solution of problem of purification of surface plate from urbanized territories. Phytofilters answer the nowadays purposes to systems of purification of land drainage. The main problem of it is restrictions, connecter with its use in the conditions of cold temperature. Manufactured a technology and mechanism, which provide a whole-year purification of surface plate and its storage. Experimentally stated optimal makeup of filtering load: peat, zeolite and sand in per cent of volume, which provides defined hydraulic characteristics. Stated sorbate and ion-selective volume of complex filtering load of ordered composition in dynamic conditions. Estimated dependences of exit concentrations of oil products and heavy metals on temperature by filtering through complex filtering load of ordered composition. Defined effectiveness of purification at phytofiltering installation. Fixed an influence of embryophytes on process of phytogeneration and capacity of filtering load. Recommended swamp iris, mace reed and reed grass. Manufactured phytofilter calculation methodology. Calculated economic effect from use of phytofiltration technology in comparison with traditional block-modular installations.

[Efficiency of the preparation "Ekolan-M" for purification of oil polluted soil].

Science.gov (United States)

Nogina, T M; Dumanskaia, T U; Khomenko, L A; Podgorskiĭ, V S

2012-01-01

The efficiency of purification of oil contaminated loamy chernozem by the preparation "Ekolan-M" was investigated. During 12 months a complex soil bioremediation using the preparation and alfalfa, as the land-improving plant, at the final stage of purification resulted in the reduction of hydrocarbon content by 97.0%, and without the preparation - by 65.5 %. In the version of experiment with the preparation a 100% decrease of soil phytotoxicity was achieved and a significant stimulation of plant growth and development was observed. The process of soil purification was accompanied by intensive development of hydrocarbon-oxidizing microorganisms, the amount of which during the process of oil concentration gradually decreased, approaching the level in the control uncontaminated soil.

Review of Membranes for Helium Separation and Purification

Directory of Open Access Journals (Sweden)

Colin A. Scholes

2017-02-01

Full Text Available Membrane gas separation has potential for the recovery and purification of helium, because the majority of membranes have selectivity for helium. This review reports on the current state of the research and patent literature for membranes undertaking helium separation. This includes direct recovery from natural gas, as an ancillary stage in natural gas processing, as well as niche applications where helium recycling has potential. A review of the available polymeric and inorganic membranes for helium separation is provided. Commercial gas separation membranes in comparable gas industries are discussed in terms of their potential in helium separation. Also presented are the various membrane process designs patented for the recovery and purification of helium from various sources, as these demonstrate that it is viable to separate helium through currently available polymeric membranes. This review places a particular focus on those processes where membranes are combined in series with another separation technology, commonly pressure swing adsorption. These combined processes have the most potential for membranes to produce a high purity helium product. The review demonstrates that membrane gas separation is technically feasible for helium recovery and purification, though membranes are currently only applied in niche applications focused on reusing helium rather than separation from natural sources.

Discussion on runoff purification technology of highway bridge deck based on water quality safety

Science.gov (United States)

Tan, Sheng-guang; Liu, Xue-xin; Zou, Guo-ping; Xiong, Xin-zhu; Tao, Shuang-cheng

2018-06-01

Aiming at the actual problems existing, including a poor purification effect of highway bridge runoff collection and treatment system across sensitive water and necessary manual emergency operation, three kinds of technology, three pools system of bridge runoff purification, the integral pool of bridge runoff purification and ecological planting tank, are put forward by optimizing the structure of purification unit and system setting. At the same time, we come up with an emergency strategy for hazardous material leakage basing on automatic identification and remote control of traffic accidents. On the basis of combining these with the optimized pool structure, sensitive water safety can be guaranteed and water pollution, from directly discharging of bridge runoff, can be decreased. For making up for the shortages of green highway construction technology, the technique has important reference value.

Synthesis of O-(2-[18F]fluoroethyl)-L-tyrosine based on a cartridge purification method

International Nuclear Information System (INIS)

Mueller, Dirk; Klette, Ingo; Kalb, Fabrizia; Baum, Richard P.

2011-01-01

Introduction: O-(2-[ 18 F]fluoroethyl)-L-tyrosine (FET) is widely used as a positron emission tomography tracer for brain tumors. Usually, a high-performance liquid chromatography (HPLC) purification at the end of the two-step synthesis is applied. In this work, we report an automatic radiosynthesis of FET with a purification procedure based on standard cartridges. Methods: O-(2-[ 18 F]fluoroethyl)-L-tyrosine was prepared by [ 18 F]fluoroethylation of L-tyrosine by a two-step synthesis using a modified [ 11 C]methionine module (Nuclear Interface). In the first reaction step, we synthesized [ 18 F]fluoroethyltosylate starting from [ 18 F]fluoride. After a purification step, L-tyrosine was [ 18 F]fluoroethylated with [ 18 F]fluoroethyltosylate. The final reaction mixture was purified by means of solid phase extraction. The FET was trapped on an SCX cartridge, eluted with saline solution and trapped again on an HRX cartridge. For a second purification step, the FET was eluted from the HRX cartridge with ammonium acetate buffer and collected on two SCX cartridges followed by a washing step with water. The final product was eluted with saline solution and neutralised with 450 μl NaHCO 3 solution (8.4%). Results: The synthesis was finished after 50 min and delivered the FET in a range of 3-16 GBq. The synthesis typically yielded 41% (21 experiments) of FET (d.c.) without an HPLC purification step. The radiochemical purity ranged between 97% and 100%. Conclusion: We present a radiosynthesis of FET where the usually used HPLC purification procedure has been substituted by a purification step based on standard cartridges. This method is useful for automatic modules without an expensive HPLC purification unit and for the routine production of FET.

Plasmid pVAX1-NH36 purification by membrane and bead perfusion chromatography.

Science.gov (United States)

Franco-Medrano, Diana Ivonne; Guerrero-Germán, Patricia; Montesinos-Cisneros, Rosa María; Ortega-López, Jaime; Tejeda-Mansir, Armando

2017-03-01

The demand for plasmid DNA (pDNA) has increased in response to the rapid advances in vaccines applications to prevent and treat infectious diseases caused by virus, bacteria or parasites, such as Leishmania species. The immunization protocols require large amounts of supercoiled plasmid DNA (sc-pDNA) challenging the development of efficient and profitable processes for capturing and purified pDNA molecules from large volumes of lysates. A typical bioprocess involves four steps: fermentation, primary recovery, intermediate recovery and final purification. Ion-exchange chromatography is one of the key operations in the purification schemes of pDNA owing the chemical structure of these macromolecules. The goal of this research was to compare the performance of the final purification step of pDNA using ion-exchange chromatography on columns packed with Mustang Q membranes or perfusive beads POROS 50 HQ. The experimental results showed that both matrixes could separate the plasmid pVAX1-NH36 (3936 bp) from impurities in clarified Escherichia coli lysates with an adequate resolution. In addition, a 24- and 21-fold global purification factor was obtained. An 88 and 63% plasmid recuperation was achieved with ion-exchange membranes and perfusion beads, respectively. A better understanding of perfusion-based matrices for the purification of pDNA was developed in this research.

Purification Simulation With Vapor Permeation and Distillation-Adsorption In Bioethanol Plant

OpenAIRE

Misri Gozan; Mia Sari Setiawan; Kenny Lischer

2017-01-01

High purity of Bioethanol is required in biofuel mixing with gasoline (EXX). In bioethanol production line, the azeotropic property of ethanol-water becomes the barrier for purification process. This study examined two bioethanol separation processes by support of simulation tools, Superpro Designer 9.0 software. Ethanol purity and a low costeconomical process were the major considerations. Purification method of vapor permeation membrane technology was compared with distillation-adsorption m...

Technology of thorium concentrates purification and their transformation in pure nuclear products

International Nuclear Information System (INIS)

Ikuta, A.

1977-01-01

An experimental study for the purification of thorium concentrates by solvent extraction is presented. The product of purification is appropriate for utilization in the fabrication of nuclear reactor fuel elements. The experiments are carried out in a laboratory scale and the following operations are studied: dissolution, extraction-scrubbing, stripping-scrubbing, thorium oxalate precipitation, and thorium nitrate coagulation [pt

Standard test method for isotopic analysis of hydrolyzed uranium hexafluoride and uranyl nitrate solutions by thermal ionization mass spectrometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2005-01-01

1.1 This method applies to the determination of isotopic composition in hydrolyzed nuclear grade uranium hexafluoride. It covers isotopic abundance of 235U between 0.1 and 5.0 % mass fraction, abundance of 234U between 0.0055 and 0.05 % mass fraction, and abundance of 236U between 0.0003 and 0.5 % mass fraction. This test method may be applicable to other isotopic abundance providing that corresponding standards are available. 1.2 This test method can apply to uranyl nitrate solutions. This can be achieved either by transforming the uranyl nitrate solution to a uranyl fluoride solution prior to the deposition on the filaments or directly by depositing the uranyl nitrate solution on the filaments. In the latter case, a calibration with uranyl nitrate standards must be performed. 1.3 This test method can also apply to other nuclear grade matrices (for example, uranium oxides) by providing a chemical transformation to uranyl fluoride or uranyl nitrate solution. 1.4 This standard does not purport to address al...

Uniform deposition of uranium hexafluoride (UF6): Standardized mass deposits and controlled isotopic ratios using a thermal fluorination method

Energy Technology Data Exchange (ETDEWEB)

McNamara, Bruce K.; O’Hara, Matthew J.; Casella, Andrew M.; Carter, Jennifer C.; Addleman, R. Shane; MacFarlan, Paul J.

2016-07-01

Abstract: We report a convenient method for the generation of volatile uranium hexafluoride (UF6) from solid uranium oxides and other uranium compounds, followed by uniform deposition of low levels of UF6 onto sampling coupons. Under laminar flow conditions, UF6 is shown to interact with surfaces within the chamber to a highly predictable degree. We demonstrate the preparation of uranium deposits that range between ~0.01 and 470±34 ng∙cm-2. The data suggest the method can be extended to creating depositions at the sub-picogram∙cm-2 level. Additionally, the isotopic composition of the deposits can be customized by selection of the uranium source materials. We demonstrate a layering technique whereby two uranium solids, each with a different isotopic composition, are employed to form successive layers of UF6 on a surface. The result is an ultra-thin deposit of UF6 that bears an isotopic signature that is a composite of the two uranium sources. The reported deposition method has direct application to the development of unique analytical standards for nuclear safeguards and forensics.

Production of elemental fluorine at IPEN - S. Paulo, Brazil

International Nuclear Information System (INIS)

Abrao, A.; Ikuta, A.; Wirkner, F.M.; Silva, F.P. da.

1981-04-01

The construction, installation and operation of a pilot unit for electrolytic generation of elemental fluorine are described. The 400 A monel electrolytic cell is heated by a water jacket. The electrolyte has the composition KF.1,8 - 2,0 HF that is maintained by intermittent addition of gaseous HF. Pre-electrolysis is made using nickel anodes which are then exchanged by non-graphitized carbon ones. Systems for purification of elemental fluorine by cryoscopy and absortion of HF, compression and storage for fluorine are described. Pure fluorine is used for the preparation of uranium hexafluoride. Identification of problems and difficulties and their solution are pointed out. (Author) [pt

High-Yield Purification, Preservation, and Serial Transplantation of Human Satellite Cells

Directory of Open Access Journals (Sweden)

Steven M. Garcia

2018-03-01

Full Text Available Summary: Investigation of human muscle regeneration requires robust methods to purify and transplant muscle stem and progenitor cells that collectively constitute the human satellite cell (HuSC pool. Existing approaches have yet to make HuSCs widely accessible for researchers, and as a result human muscle stem cell research has advanced slowly. Here, we describe a robust and predictable HuSC purification process that is effective for each human skeletal muscle tested and the development of storage protocols and transplantation models in dystrophin-deficient and wild-type recipients. Enzymatic digestion, magnetic column depletion, and 6-marker flow-cytometric purification enable separation of 104 highly enriched HuSCs per gram of muscle. Cryostorage of HuSCs preserves viability, phenotype, and transplantation potential. Development of enhanced and species-specific transplantation protocols enabled serial HuSC xenotransplantation and recovery. These protocols and models provide an accessible system for basic and translational investigation and clinical development of HuSCs. : Garcia and colleagues report methods for efficient purification of satellite cells from human skeletal muscle. They use their approaches to demonstrate stem cell functions of endogenous satellite cells and to make human satellite cells accessible for sharing among researchers. Keywords: human satellite cell purification, serial transplantation, satellite cell cryopreservation

The Purification Method of Matching Points Based on Principal Component Analysis

Directory of Open Access Journals (Sweden)

DONG Yang

2017-02-01

Full Text Available The traditional purification method of matching points usually uses a small number of the points as initial input. Though it can meet most of the requirements of point constraints, the iterative purification solution is easy to fall into local extreme, which results in the missing of correct matching points. To solve this problem, we introduce the principal component analysis method to use the whole point set as initial input. And thorough mismatching points step eliminating and robust solving, more accurate global optimal solution, which intends to reduce the omission rate of correct matching points and thus reaches better purification effect, can be obtained. Experimental results show that this method can obtain the global optimal solution under a certain original false matching rate, and can decrease or avoid the omission of correct matching points.

Technical project for a new water purification solution

Directory of Open Access Journals (Sweden)

Toma Adina

2018-01-01

Full Text Available This research is part of the RO-BG Cross-Border Cooperation Program, project “CLEANDANUBE”, MIS-ETC 653, which has finalised by providing a common strategy to prevent the Danube’s pollution technological risks with oil and oil products. This paper presents a new sustainable water purification solution. A short introduction will be offered and an overview regarding the research and new methods to greening the waste is provided. The theoretical aspects of the centrifugal separation phenomenon are studied and the preliminary project bases were established. The paper conveys the possible constructive variations and the technological implications of those. Ultimately, the technical project for a new water purification solution and conclusions with critical points encountered during the designing phase are presented.

Enriched Water-H2 18O Purification to be Used in Routine 18FDG Production

International Nuclear Information System (INIS)

Al Rayyes, A.H.

2009-01-01

Oxygen-18 enriched water has been recovered from IBA (Ion Beam Applications) recovery system followed by purification and then used in the production of 18 F-. The purification process has been carried out by irradiation with UV followed by a distillation under vacuum. After purification, 95% of water is recovered and organic compounds, radioisotopes, trace metals and gases are eliminated efficiently. Results show that there are no significant differences in (2-deoxy-2-[ 18 F]fluoro-D-glucose ([ 18 F]FDG) production yield using purified water by the proposed method and new enriched water. Tritium was detected in the irradiated enriched water. Contamination precautions during purification should be considered. Tritium was not present in 18 FDG or Na- 18 F final products. (author)

Method for Rapid Purification of Class IIa Bacteriocins and Comparison of Their Activities

OpenAIRE

Guyonnet, D.; Fremaux, C.; Cenatiempo, Y.; Berjeaud, J. M.

2000-01-01

A three-step method was developed for the purification of mesentericin Y105 (60% yield) from the culture supernatant of Leuconostoc mesenteroides Y105. The same procedure was successfully applied to the purification of five other anti-Listeria bacteriocins identified by mass spectrometry. Specific activities of the purified bacteriocins were compared.

Expression and purification of recombinant nattokinase in Spodoptera frugiperda cells.

Science.gov (United States)

Li, Xiaoxiang; Wang, Xiaoli; Xiong, Shaoling; Zhang, Jing; Cai, Litao; Yang, Yanyan

2007-10-01

A recombinant baculovirus, rv-egfp-NK, containing a reporter gene encoding the enhanced green fluorescent protein (EGFP), was used to express nattokinase (NK), a fibrinolytic enzyme, in Spodoptera frugiperda (SF-9) cells. The recombinant protein also included a histidine tag for purification using Ni(2+) resins. The recombinant NK, approximately 30 kDa, retained fibrinolytic activity (60 U/ml). The integration of the EGFP expression cassette in the Bac-to-Bac system is thus an effective method for the expression and purification of recombinant NK protein in Spodoptera frugiperda insect cells.

Gas purification project

International Nuclear Information System (INIS)

Broothaerts, J.; Claes, J.; Collard, G.; Goossens, W.; Harnie, R.; Heylen, P.; Vaesen, J.; Beukelaer, R. de; Dubois, G.; Glibert, R.; Mestrez, J.; Zahlen, A.

1975-06-01

Conceptual and experimental studies on LMFBR reprocessing and reactor off-gas purification systems are summarized. Iodine sorption on zeolites, low-temperature adsorption of noble gases on charcoal and catalytic oxidation of hydrogen, simulating tritium, are being studied in laboratory set-ups. A pilot loop with 25 m 3 h -1 throughput has been constructed. Results are quoted from the first phase of the iodine removal programme by scrubbing systems. Further extension of the test loop, comprising off-gases conditioning to removal of krypton in a cryodistillation unit, has been prepared. Delay-bed studies on 133 Xe extraction from LWR off-gases are reported. (author)

Transuranium element purification by liquid-liquid extraction

International Nuclear Information System (INIS)

Madic, C.; Koehly, G.

1976-01-01

In the transuranium element production, the liquid-liquid extraction purification is presented. The affinity of TBP and trilaurylammonium nitrate for these elements is given. Exemples of NP/Pu, Pu/Np, U/Pu, Am/Cm, Am and Cm/Ln separation are presented [fr

Fungal laccase: copper induction, semi-purification, immobilization ...

African Journals Online (AJOL)

Fungal laccase: copper induction, semi-purification, immobilization, phenolic effluent treatment and electrochemical measurement. ... In order to apply in an effluent treatment, laccase was immobilized on different vitroceramics supports, pyrolytic graphite and also on a carbon fiber electrode as biosensor. The maximum ...

Purification and characterization of xylanase from Aspergillus ...

African Journals Online (AJOL)

Xylanase was subjected to a three-step purification scheme involving ammonium sulphate precipitation, gel filtration chromatography and anion exchange chromatography. Purity was verified by running the extracted protein on sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and a single band was ...

Zone distillation: a new purification method

International Nuclear Information System (INIS)

Kravchenko, A.I.

2011-01-01

The features of zone distillation (with zone melting of refined material and with pulling of condensate) as a new purification method are shown. The method is based on similarity of equations of distillation and crystallization refining. The analogy between some distillation and condensation methods (particularly between zone distillation and zone recrystallization) is should up

Method for Rapid Purification of Class IIa Bacteriocins and Comparison of Their Activities

Science.gov (United States)

Guyonnet, D.; Fremaux, C.; Cenatiempo, Y.; Berjeaud, J. M.

2000-01-01

A three-step method was developed for the purification of mesentericin Y105 (60% yield) from the culture supernatant of Leuconostoc mesenteroides Y105. The same procedure was successfully applied to the purification of five other anti-Listeria bacteriocins identified by mass spectrometry. Specific activities of the purified bacteriocins were compared. PMID:10742275

Different purification methods and quality of sunflower biodiesel

Energy Technology Data Exchange (ETDEWEB)

Pighinelli, A.L.M.T.; Park, K.J. [Campinas State Univ., Sao Paulo (Brazil). School of Agricultural Engineering; Ferrari, R.A.; Miguel, A.M.R.O. [Food Technology Inst., Sao Paulo (Brazil)

2010-07-01

Biodiesel is derived from triacylglycerides and is produced primarily through transesterification, a chemical reaction of vegetable oils with alcohol, methanol or ethanol. The cost of raw material should be considered since 85 per cent of production cost is related to vegetable oil. The purpose of this study was to evaluate oil expression of sunflower seed. It also examined the sunflower crude oil as a raw material for biodiesel by transesterification in both laboratory and pilot scale studies. Three different biodiesel purification methods were examined. The best result for oil expelling (68.4 per cent) at the experimental stage was obtained for seeds with a moisture content of 6.9 per cent at 25 degrees C and at a screw speed of 114 rpm. For biodiesel production at the laboratory scale, the best result for oil expelling was 87.5 per cent. It was obtained with an ethanol:oil molar ratio of 4.7:1 and with a 4.42 per cent catalyst concentration related to the quantity of oil that had to be transesterified. The experimental condition was applied at a bigger scale with a batch stirred tank reactor. For purification with washing, the biodiesel yield was 84.2 per cent. Purification with silica resulted in a yield of 84.6 per cent. A better quality biofuel was obtained through distillation of biodiesel.

A comprehensive review on biodiesel purification and upgrading

Directory of Open Access Journals (Sweden)

Hamed Bateni

2017-09-01

Full Text Available Serious environmental concerns regarding the use of fossil-based fuels have raised awareness regarding the necessity of alternative clean fuels and energy carriers. Biodiesel is considered a clean, biodegradable, and non-toxic diesel substitute produced via the transesterification of triglycerides with an alcohol in the presence of a proper catalyst. After initial separation of the by-product (glycerol, the crude biodiesel needs to be purified to meet the standard specifications prior to marketing. The presence of impurities in the biodiesel not only significantly affects its engine performance but also complicates its handling and storage. Therefore, biodiesel purification is an essential step prior to marketing. Biodiesel purification methods can be classified based on the nature of the process into equilibrium-based, affinity-based, membrane-based, reaction-based, and solid-liquid separation processes. The main adverse properties of biodiesel – namely moisture absorption, corrosiveness, and high viscosity – primarily arise from the presence of oxygen. To address these issues, several upgrading techniques have been proposed, among which catalytic (hydrodeoxygenation using conventional hydrotreating catalysts, supported metallic materials, and most recently transition metals in various forms appear promising. Nevertheless, catalyst deactivation (via coking and/or inadequacy of product yields necessitate further research. This paper provides a comprehensive overview on the techniques and methods used for biodiesel purification and upgrading.

Multi-copy entanglement purification with practical spontaneous parametric down conversion sources

Science.gov (United States)

Zhang, Shuai-Shuai; Shu, Qi; Zhou, Lan; Sheng, Yu-Bo

2017-06-01

Entanglement purification is to distill the high quality entanglement from the low quality entanglement with local operations and classical communications. It is one of the key technologies in long-distance quantum communication. We discuss an entanglement purification protocol (EPP) with spontaneous parametric down conversion (SPDC) sources, in contrast to previous EPP with multi-copy mixed states, which requires ideal entanglement sources. We show that the SPDC source is not an obstacle for purification, but can benefit the fidelity of the purified mixed state. This EPP works for linear optics and is feasible in current experiment technology. Project supported by the National Natural Science Foundation of China (Grant Nos. 11474168 and 61401222), the Natural Science Foundation of Jiangsu Province, China (Grant No. BK20151502), the Qing Lan Project in Jiangsu Province, China, and a Project Funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions, China.

Rapid purification of radiodinated glucagon with Sep-PakR reversed phase cartridges

International Nuclear Information System (INIS)

Borghi, V.C.; Nascimento, M.; Wajchenberg, B.L.

1989-01-01

A simple, rapid method is described for the purification of radioiodinated glucagon for use in radioimmunoassay. Samples of the radioiodinated hormone, before and after purification are analysed on polyacrylamide gel electrophoresis. The 125 I incorporation in these samples is also checked through thrichloroacetic acid precipitation. The usefulness of this labeled glucagon in radioimmunoassay is demonstrated by its biding to specific antibodies. (M.A.C.) [pt

Joint ANSI-INMM 8.1: Nuclear Regulatory Commission study of uranium hexafluoride cylinder material accountability bulk measurements

International Nuclear Information System (INIS)

Pontius, P.E.; Doher, L.W.

1977-01-01

This paper reports the progress to date in a demonstration of the procedures in ANSI N15.18-1975, ''Mass Calibration Techniques for Nuclear Material Control,'' sponsored and funded by the Nuclear Regulatory Commission (NRC). The philosophy of mass measurement as a production process, as promulgated in ANSI N15.18-1975, is reviewed. Special emphasis is placed on the use of artifact Reference Mass Standards (RMS) as references for uranium hexafluoride (UF 6 ) calibration and bulk measurement processes. The history of the creation of the artifact concept and its adoption by ANSI N15.18-1975 and the Nuclear Regulatory Commission is narrated. The program now under way is specifically described; including descriptions of the RMS, their calibration, and the assignment of uncertainties to them by the National Bureau of Standards (NBS). Instrument tests, in-house standards (IHS), and assignment of values relative to the RMS-NBS values at nuclear facilities which measure UF 6 cylinders are described. Comparisons and the data base are detailed to provide realistic measurement process parameters associated with accountable transfer of UF 6 . The as yet uncompleted part of the demonstration is described, that is, to further close the measurement loop by verification both between and within facilities

Purification, characterization of phytase enzyme from Lactobacillus ...

African Journals Online (AJOL)

Purification, characterization of phytase enzyme from Lactobacillus plantarum bacteria and determination of its kinetic properties. ... Many of the cereal grains, legumes and oilseeds store phosphorus in phytate form. Phytases can be produced by plants, animals and microorganisms. However, the ones with microbial origin ...

Composting Guilt: An Ecological Critique of Purification of Past Wrongdoing

Directory of Open Access Journals (Sweden)

Katharina von Kellenbach

2014-03-01

Full Text Available A review of the fast growing body of literature on transitional justice (Hayner 2011, political reconciliation (Philpott 2006, Verdejo 2009, forgiveness (Amstutz 2005, apology (Celermajer 2009, guilt (Barkan 2000 repentance (Schimmel 2002, evil (Meister 2011, moral repair (Walker 2006, and cultural memory (Borneman 2011, shows that the concept of purification has so far received little attention.  But the language of purification operates in the background of diverse practices such as the exhumation and ceremonial reburial of the dead (Desbois 2009, the call for truth commissions to document wrongdoing, and reparation campaigns that apologize and offer restitution (Diner 2007. At their best, truth and reconciliation commissions create cathartic moments (Greek: katharos = pure and facilitate “performative transformations” that cleanse relations between perpetrators and victims (Cole 2010, 15. My new project, still in its early stages, asks whether the concept and ritual practice of purification can be used to enhance moral repair in individuals and to serve the restoration of social order in the aftermath of atrocity and systemic human rights abuses.

Use of a palladium catalyst in the purification of coke oven gas

Energy Technology Data Exchange (ETDEWEB)

Gotoh, T; Nakamura, M; Hirooka, N

1986-01-01

In the production of hydrogen from coke oven gas (COG) by pressure swing adsorption (PSA), various impurities in the COG have to be removed prior to the PSA. The stages of this purification are as follows: 1) removal of polymerizable substances such as NO gum by compressing the COG and then feeding it through a hot bottle and cooler arrangement; 2) removal of BTX in a scrubber; 3) removal of naphthalene and mist by means of chillers and filters; 4) removal of oxygen in a special reactor using a Pd catalyst. These various purification treatments have enabled the PSA plant to operate smoothly for 3.5 years. The authors report the results of pilot plant tests, and compare the results obtained using alternative purification techniques. 4 figures, 5 tables.

Improved purification of immunoglobulin G from plasma by mixed-mode chromatography.

Science.gov (United States)

Chai, Dong-Sheng; Sun, Yan; Wang, Xiao-Ning; Shi, Qing-Hong

2014-12-01

Efficient loading of immunoglobulin G in mixed-mode chromatography is often a serious bottleneck in the chromatographic purification of immunoglobulin G. In this work, a mixed-mode ligand, 4-(1H-imidazol-1-yl) aniline, was coupled to Sepharose Fast Flow to fabricate AN SepFF adsorbents with ligand densities of 15-64 mmol/L, and the chromatographic performances of these adsorbents were thoroughly investigated to identify a feasible approach to improve immunoglobulin G purification. The results indicate that a critical ligand density exists for immunoglobulin G on the AN SepFF adsorbents. Above the critical ligand density, the adsorbents showed superior selectivity to immunoglobulin G at high salt concentrations, and also exhibited much higher dynamic binding capacities. For immunoglobulin G purification, both the yield and binding capacity increased with adsorbent ligand density along with a decrease in purity. It is difficult to improve the binding capacity, purity, and yield of immunoglobulin G simultaneously in AN SepFF chromatography. By using tandem AN SepFF chromatography, a threefold increase in binding capacity as well as high purity and yield of immunoglobulin G were achieved. Therefore, the tandem chromatography demonstrates that AN SepFF adsorbent is a practical and feasible alternative to MEP HyperCel adsorbents for immunoglobulin G purification. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-throughput purification of recombinant proteins using self-cleaving intein tags.

Science.gov (United States)

Coolbaugh, M J; Shakalli Tang, M J; Wood, D W

2017-01-01

High throughput methods for recombinant protein production using E. coli typically involve the use of affinity tags for simple purification of the protein of interest. One drawback of these techniques is the occasional need for tag removal before study, which can be hard to predict. In this work, we demonstrate two high throughput purification methods for untagged protein targets based on simple and cost-effective self-cleaving intein tags. Two model proteins, E. coli beta-galactosidase (βGal) and superfolder green fluorescent protein (sfGFP), were purified using self-cleaving versions of the conventional chitin-binding domain (CBD) affinity tag and the nonchromatographic elastin-like-polypeptide (ELP) precipitation tag in a 96-well filter plate format. Initial tests with shake flask cultures confirmed that the intein purification scheme could be scaled down, with >90% pure product generated in a single step using both methods. The scheme was then validated in a high throughput expression platform using 24-well plate cultures followed by purification in 96-well plates. For both tags and with both target proteins, the purified product was consistently obtained in a single-step, with low well-to-well and plate-to-plate variability. This simple method thus allows the reproducible production of highly pure untagged recombinant proteins in a convenient microtiter plate format. Copyright © 2016 Elsevier Inc. All rights reserved.

Application of hydrometallurgy techniques in quartz processing and purification: a review

Science.gov (United States)

Lin, Min; Lei, Shaomin; Pei, Zhenyu; Liu, Yuanyuan; Xia, Zhangjie; Xie, Feixiang

2018-04-01

Although there have been numerous studies on separation and purification of metallic minerals by hydrometallurgy techniques, applications of the chemical techniques in separation and purification of non-metallic minerals are rarely reported. This paper reviews disparate areas of study into processing and purification of quartz (typical non-metallic ore) in an attempt to summarize current work, as well as to suggest potential for future consolidation in the field. The review encompasses chemical techniques of the quartz processing including situations, progresses, leaching mechanism, scopes of application, advantages and drawbacks of micro-bioleaching, high temperature leaching, high temperature pressure leaching and catalyzed high temperature pressure leaching. Traditional leaching techniques including micro-bioleaching and high temperature leaching are unequal to demand of modern glass industry for quality of quartz concentrate because the quartz products has to be further processed. High temperature pressure leaching and catalyzed high temperature pressure leaching provide new ways to produce high-grade quartz sand with only one process and lower acid consumption. Furthermore, the catalyzed high temperature pressure leaching realizes effective purification of quartz with extremely low acid consumption (no using HF or any fluoride). It is proposed that, by integrating the different chemical processes of quartz processing and expounding leaching mechanisms and scopes of application, the research field as a monopolized industry would benefit.

Purification of infectious adenovirus in two hours by ultracentrifugation and tangential flow filtration

International Nuclear Information System (INIS)

Ugai, Hideyo; Yamasaki, Takahito; Hirose, Megumi; Inabe, Kumiko; Kujime, Yukari; Terashima, Miho; Liu, Bingbing; Tang, Hong; Zhao, Mujun; Murata, Takehide; Kimura, Makoto; Pan, Jianzhi; Obata, Yuichi; Hamada, Hirofumi; Yokoyama, Kazunari K.

2005-01-01

Adenoviruses are excellent vectors for gene transfer and are used extensively for high-level expression of the products of transgenes in living cells. The development of simple and rapid methods for the purification of stable infectious recombinant adenoviruses (rAds) remains a challenge. We report here a method for the purification of infectious adenovirus type 5 (Ad5) that involves ultracentrifugation on a cesium chloride gradient at 604,000g for 15 min at 4 deg C and tangential flow filtration. The entire procedure requires less than two hours and infectious Ad5 can be recovered at levels higher than 64% of the number of plaque-forming units (pfu) in the initial crude preparation of viruses. We have obtained titers of infectious purified Ad5 of 1.35 x 10 10 pfu/ml and a ratio of particle titer to infectious titer of seven. The method described here allows the rapid purification of rAds for studies of gene function in vivo and in vitro, as well as the rapid purification of Ad5

Gas-phase thermal dissociation of uranium hexafluoride: Investigation by the technique of laser-powered homogeneous pyrolysis

International Nuclear Information System (INIS)

Bostick, W.D.; McCulla, W.H.; Trowbridge, L.D.

1987-04-01

In the gas-phase, uranium hexafluoride decomposes thermally in a quasi-unimolecular reaction to yield uranium pentafluoride and atomic fluorine. We have investigated this reaction using the relatively new technique of laser-powered homogeneous pyrolysis, in which a megawatt infrared laser is used to generate short pulses of high gas temperatures under strictly homogeneous conditions. In our investigation, SiF 4 is used as the sensitizer to absorb energy from a pulsed CO 2 laser and to transfer this energy by collisions with the reactant gas. Ethyl chloride is used as an external standard ''thermometer'' gas to permit estimation of the unimolecular reaction rate constants by a relative rate approach. When UF 6 is the reactant, CF 3 Cl is used as reagent to trap atomic fluorine reaction product, forming CF 4 as a stable indicator which is easily detected by infrared spectroscopy. Using these techniques, we estimate the UF 6 unimolecular reaction rate constant near the high-pressure limit. In the Appendix, we describe a computer program, written for the IBM PC, which predicts unimolecular rate constants based on the Rice-Ramsperger-Kassel theory. Parameterization of the theoretical model is discussed, and recommendations are made for ''appropriate'' input parameters for use in predicting the gas-phase unimolecular reaction rate for UF 6 as a function of temperature and gas composition and total pressure. 85 refs., 17 figs., 14 tabs

Water purification using organic salts

Science.gov (United States)

Currier, Robert P.

2004-11-23

Water purification using organic salts. Feed water is mixed with at least one organic salt at a temperature sufficiently low to form organic salt hydrate crystals and brine. The crystals are separated from the brine, rinsed, and melted to form an aqueous solution of organic salt. Some of the water is removed from the aqueous organic salt solution. The purified water is collected, and the remaining more concentrated aqueous organic salt solution is reused.

Partial purification and biochemical characterization of acid ...

African Journals Online (AJOL)

Mung bean (Vigna radiata) is one of the important crops of the North Eastern Region of India. In the present study, acid phosphatase enzyme was isolated and partially purified from germinated local mung bean seeds. The sequential partial purification process was performed using ammonium sulphate precipitation method.

Optimal purification technology of ultrapure water for instrumental analysis

International Nuclear Information System (INIS)

Ishii, Naoe

2011-01-01

Purified water is one of the most commonly utilized reagents in the laboratory. It is used throughout experimental protocols in virtually every type of laboratory application : as blanks, for the dissolution and dilution of samples, the dilution of standards, preparation of mobile phases and for media and buffer preparation. Contaminants present in purified water can therefore have a significant impact on results. Hence, it is important to ensure that the laboratory water-purification system contains a combination of purification technologies to target specific impurities related to each application. This article looks at some of these technologies and their relevance for specific applications, such as HPLC, LC/MS, and ion chromatography (IC). (author)

Purification of the functional plant membrane channel KAT1

International Nuclear Information System (INIS)

Hibi, Takao; Aoki, Shiho; Oda, Keisuke; Munemasa, Shintaro; Ozaki, Shunsuke; Shirai, Osamu; Murata, Yoshiyuki; Uozumi, Nobuyuki

2008-01-01

The inward-rectifying K + channel KAT1 is expressed mainly in Arabidopsis thaliana guard cells. The purification of functional KAT1 has never been reported. We investigated the extraction of the plant K + channel KAT1 with different detergents, as an example for how to select detergents for purifying a eukaryotic membrane protein. A KAT1-GFP fusion protein was used to screen a library of 46 detergents for the effective solubilization of intact KAT1. Then, a 'test set' of three detergents was picked for further analysis, based on their biochemical characteristics and availability. The combination use of the selected detergents enabled the effective purification of functional KAT1 with affinity and gel-filtration chromatography

A simple method for affinity purification of radiolabeled monoclonal antibodies

Energy Technology Data Exchange (ETDEWEB)

Juweid, M; Sato, J; Paik, C; Onay-Basaran, S; Weinstein, J N; Neumann, R D [National Cancer Inst., Bethesda, MD (United States)

1993-04-01

A simple method is described for affinity purification of radiolabeled antibodies using glutaraldehyde-fixed tumor target cells. The cell-bound antibody fraction is removed from the cells by an acid wash and then immediately subjected to buffer-exchange chromatography. The method was applied to the D3 murine monoclonal antibody which binds to a 290 kDa antigen on the surface of Line 10 guinea pig carcinoma cells. No alteration in the molecular size profile was detected after acid washing. Purification resulted in a significant increase in immunoreactivity by an average of 14 [+-] 47% (SD; range 4-30%). (author).

Purification of beta-acetylglucosaminase and beta-galactosidase from ram testis.

Science.gov (United States)

Caygill, J C; Roston, C P; Jevons, F R

1966-02-01

1. The presence of beta-galactosidase (EC 3.2.1.23) in an acetic acid extract of ram testis is reported. Some properties of the crude enzyme preparation were studied. 2. The purification of beta-acetylglucosaminase (EC 3.2.1.30) and of beta-galactosidase from the ram-testis extract by ammonium sulphate precipitation and chromatography on a CM-cellulose column is described. 3. The final purifications of the separated enzymes achieved were for the beta-acetylglucosaminase 35 times and for the beta-galactosidase 99 times. 4. The possibility of using DEAE-cellulose and Sephadex G-200 to purify the enzymes was investigated.

The Viability of Photocatalysis for Air Purification

Directory of Open Access Journals (Sweden)

Stephen O. Hay

2015-01-01

Full Text Available Photocatalytic oxidation (PCO air purification technology is reviewed based on the decades of research conducted by the United Technologies Research Center (UTRC and their external colleagues. UTRC conducted basic research on the reaction rates of various volatile organic compounds (VOCs. The knowledge gained allowed validation of 1D and 3D prototype reactor models that guided further purifier development. Colleagues worldwide validated purifier prototypes in simulated realistic indoor environments. Prototype products were deployed in office environments both in the United States and France. As a result of these validation studies, it was discovered that both catalyst lifetime and byproduct formation are barriers to implementing this technology. Research is ongoing at the University of Connecticut that is applicable to extending catalyst lifetime, increasing catalyst efficiency and extending activation wavelength from the ultraviolet to the visible wavelengths. It is critical that catalyst lifetime is extended to realize cost effective implementation of PCO air purification.

Nanomaterials and Water Purification: Opportunities and Challenges

Science.gov (United States)

Savage, Nora; Diallo, Mamadou S.

2005-10-01

Advances in nanoscale science and engineering suggest that many of the current problems involving water quality could be resolved or greatly ameliorated using nanosorbents, nanocatalysts, bioactive nanoparticles, nanostructured catalytic membranes and nanoparticle enhanced filtration among other products and processes resulting from the development of nanotechnology. Innovations in the development of novel technologies to desalinate water are among the most exciting and promising. Additionally, nanotechnology-derived products that reduce the concentrations of toxic compounds to sub-ppb levels can assist in the attainment of water quality standards and health advisories. This article gives an overview of the use of nanomaterials in water purification. We highlight recent advances on the development of novel nanoscale materials and processes for treatment of surface water, groundwater and industrial wastewater contaminated by toxic metal ions, radionuclides, organic and inorganic solutes, bacteria and viruses. In addition, we discuss some challenges associated with the development of cost effective and environmentally acceptable functional nanomaterials for water purification.

Nanomaterials and Water Purification: Opportunities and Challenges

International Nuclear Information System (INIS)

Savage, Nora; Diallo, Mamadou S.

2005-01-01

Advances in nanoscale science and engineering suggest that many of the current problems involving water quality could be resolved or greatly ameliorated using nanosorbents, nanocatalysts, bioactive nanoparticles, nanostructured catalytic membranes and nanoparticle enhanced filtration among other products and processes resulting from the development of nanotechnology. Innovations in the development of novel technologies to desalinate water are among the most exciting and promising. Additionally, nanotechnology-derived products that reduce the concentrations of toxic compounds to sub-ppb levels can assist in the attainment of water quality standards and health advisories. This article gives an overview of the use of nanomaterials in water purification. We highlight recent advances on the development of novel nanoscale materials and processes for treatment of surface water, groundwater and industrial wastewater contaminated by toxic metal ions, radionuclides, organic and inorganic solutes, bacteria and viruses. In addition, we discuss some challenges associated with the development of cost effective and environmentally acceptable functional nanomaterials for water purification

Experimental study and simulation of phosphorus purification effects of bioretention systems on urban surface runoff.

Directory of Open Access Journals (Sweden)

Jiake Li

Full Text Available Excessive phosphorus (P contributes to eutrophication by degrading water quality and limiting human use of water resources. Identifying economic and convenient methods to control soluble reactive phosphorus (SRP pollution in urban runoff is the key point of rainwater management strategies. Through three series of different tests involving influencing factors, continuous operation and intermittent operation, this study explored the purification effects of bioretention tanks under different experimental conditions, it included nine intermittent tests, single field continuous test with three groups of different fillers (Fly ash mixed with sand, Blast furnace slag, and Soil, and eight intermittent tests with single filler (Blast furnace slag mixed with sand. Among the three filler combinations studied, the filler with fly ash mixed with sand achieved the best pollution reduction efficiency. The setting of the submerged zone exerted minimal influence on the P removal of the three filler combinations. An extension of the dry period slightly promoted the P purification effect. The combination of fly ash mixed with sand demonstrated a positive purification effect on SRP during short- or long-term simulated rainfall duration. Blast furnace slag also presented a positive purification effect in the short term, although its continuous purification effect on SRP was poor in the long term. The purification abilities of soil in the short and long terms were weak. Under intermittent operations across different seasons, SRP removal was unstable, and effluent concentration processes were different. The purification effect of the bioretention system on SRP was predicted through partial least squares regression (PLS modeling analysis. The event mean concentration removal of SRP was positively related to the adsorption capacity of filler and rainfall interval time and negatively related to submerged zones, influent concentration and volume.

Vegetation characteristics and water purification by artificial floating ...

African Journals Online (AJOL)

ajl yemi

2011-12-19

Dec 19, 2011 ... INTRODUCTION. Environmental pollution poses a grave menace to the ... major functions; 1) water purification, 2) providing habitats for certain animals ... areas. The aims were to; 1) select certain emerging plants effective at ...

Purification of a Multidrug Resistance Transporter for Crystallization Studies

Directory of Open Access Journals (Sweden)

Kamela O. Alegre

2015-03-01

Full Text Available Crystallization of integral membrane proteins is a challenging field and much effort has been invested in optimizing the overexpression and purification steps needed to obtain milligram amounts of pure, stable, monodisperse protein sample for crystallography studies. Our current work involves the structural and functional characterization of the Escherichia coli multidrug resistance transporter MdtM, a member of the major facilitator superfamily (MFS. Here we present a protocol for isolation of MdtM to increase yields of recombinant protein to the milligram quantities necessary for pursuit of structural studies using X-ray crystallography. Purification of MdtM was enhanced by introduction of an elongated His-tag, followed by identification and subsequent removal of chaperonin contamination. For crystallization trials of MdtM, detergent screening using size exclusion chromatography determined that decylmaltoside (DM was the shortest-chain detergent that maintained the protein in a stable, monodispersed state. Crystallization trials of MdtM performed using the hanging-drop diffusion method with commercially available crystallization screens yielded 3D protein crystals under several different conditions. We contend that the purification protocol described here may be employed for production of high-quality protein of other multidrug efflux members of the MFS, a ubiquitous, physiologically and clinically important class of membrane transporters.

Purification of a Recombinant Glutathione Transferase from the Causative Agent of Hydatidosis, "Echinococcus granulosus"

Science.gov (United States)

Fleitas, Andrea L.; Randall, Lía M.; Möller, Matías N.; Denicola, Ana

2016-01-01

This practical class activity was designed to introduce students to recombinant protein expression and purification. The principal goal is to shed light on basic aspects concerning recombinant protein production, in particular protein expression, chromatography methods for protein purification, and enzyme activity as a tool to evaluate purity and…

Extraction and Purification of Flavonoids from Radix Puerariae

African Journals Online (AJOL)

and preparations are now on sale. ... significant for optimization of extraction, resin selection and ... and flavonoids as indexes, optimize the proper density. ..... system. Sep Purif Technol. 2008; 62: 590-595. 12. Chen JH, Liau BC, Jong TT.

The technology of large-scale pharmaceutical plasmid purification ...

African Journals Online (AJOL)

STORAGESEVER

2010-01-04

Jan 4, 2010 ... DNA vaccine, the cost of purification must be decreased. Although commonly .... Three mice were killed every 4 days interval. Tissues of heart, liver, .... Now, methods such as chromatography had good prospects in plasmid ...

Active test of purification facility at Rokkasho reprocessing plant

Energy Technology Data Exchange (ETDEWEB)

Ishio, Takahiro; Sato, Nobuharu; Inaba, Makoto; Itagaki, Takashi [Purification Section, Plant Operation Department, Reprocessing Plant, Reprocessing Business Division, Japan Nuclear Fuel Limited, 4-108, Aza Okitsuke, Oaza Obuchi, Rokkasho-mura, Kamikita-gun, Aomori-ken (Japan)

2009-06-15

I. Introduction: At RRP, following the completion of Water Test, Chemical Test (CT) and Uranium Test (UT), the Active Test (AT) with actual spent fuel assemblies has been performed since March of 2006. This paper deals with the AT of the plutonium purification unit at RRP. II. Outline of plutonium purification unit: The plutonium purification unit purifies plutonium nitrate sent from the Separation Facility, and it has 5 pulsed columns and 4 mixer-settlers. Plutonium valence is adjusted to Pu{sup 4+} in plutonium nitrate sent from the Separation Facility, and then plutonium is extracted into organic phase (tri-butyl phosphate: TBP) in the extraction column. At this time, most of fission products remain in aqueous phase (nitric acid solution), which is discharged as raffinate through the diluent washing column. The fission products still contained in loaded organic solvent are removed in the FP scrubbing column, and then plutonium is stripped with nitric acid solution including hydroxylamine nitrate (HAN) as reducer. After TBP contained in purified plutonium nitrate solution is removed in the diluent washing bank with n-dodecane, it is sent to the plutonium concentration unit. Organic solvent used in the stripping column is sent to the plutonium barrier bank in order to remove remaining plutonium with uranous nitrate and hydrazine nitrate solution, and organic solvent is sent to the solvent regeneration unit. III. Active test results: The main purpose of the AT on the plutonium purification unit is (1) checking the performance of plutonium extraction and stripping, (2) checking the efficiency of diluent washing. III.A. Plutonium Extraction and Stripping performances: As a result of the neutron monitor profile on the extraction column during the representative operation, extraction was completed at the upper part of the column. As for the neutron monitor profile on the stripping column, stripping was performed at the lower part of the column. Plutonium concentration

Study of calcium chloride and calcium nitrate purification on inorganic sorbents

International Nuclear Information System (INIS)

Vasil'eva, L.V.; Knyazeva, A.N.; Fakeev, A.A.; Belyaeva, N.A.; Morozov, V.I.; Kucherova, V.V.

1986-01-01

Purification of calcium chloride and calcium nitrate from iron, chromium, manganese and cobalt impurities by sorption on some inorganic collectors are considered in this article. Study was conducted by means of radioactive-tracer technique at concurrent use of several γ-radioactive isotopes. As a collectors were used hydrated aluminium and zirconium oxides. Dependence of effectiveness of precipitation by collectors on ph-value of medium, quantity of collector, nature and concentration of components is studied. Optimal parameters of purification of calcium chloride and calcium nitrate are defined.

Expression, purification and characterization of the interferon ...

Indian Academy of Sciences (India)

2012-01-19

Jan 19, 2012 ... utilizing a single-step affinity purification with an appreciable yield of the highly purified protein. Recombinant RNase L was characterized by SDS-PAGE, immunoblotting and MALDI-TOF analysis. A semi-quantitative agarose-gel-based ribonuclease assay was developed for measuring its 2-5A-dependent ...

FIREPLUME model for plume dispersion from fires: Application to uranium hexafluoride cylinder fires

International Nuclear Information System (INIS)

Brown, D.F.; Dunn, W.E.

1997-06-01

This report provides basic documentation of the FIREPLUME model and discusses its application to the prediction of health impacts resulting from releases of uranium hexafluoride (UF 6 ) in fires. The model application outlined in this report was conducted for the Draft Programmatic Environmental Impact Statement for Alternative Strategies for the Long-Term Management and Use of Depleted UF 6 . The FIREPLUME model is an advanced stochastic model for atmospheric plume dispersion that predicts the downwind consequences of a release of toxic materials from an explosion or a fire. The model is based on the nonbuoyant atmospheric dispersion model MCLDM (Monte Carlo Lagrangian Dispersion Model), which has been shown to be consistent with available laboratory and field data. The inclusion of buoyancy and the addition of a postprocessor to evaluate time-varying concentrations lead to the current model. The FIREPLUME model, as applied to fire-related UF 6 cylinder releases, accounts for three phases of release and dispersion. The first phase of release involves the hydraulic rupture of the cylinder due to heating of the UF 6 in the fire. The second phase involves the emission of material into the burning fire, and the third phase involves the emission of material after the fire has died during the cool-down period. The model predicts the downwind concentration of the material as a function of time at any point downwind at or above the ground. All together, five fire-related release scenarios are examined in this report. For each scenario, downwind concentrations of the UF 6 reaction products, uranyl fluoride and hydrogen fluoride, are provided for two meteorological conditions: (1) D stability with a 4-m/s wind speed, and (2) F stability with a 1-m/s wind speed

Purification of antibody against Ara h 2 by a homemade immunoaffinity chromatography column.

Science.gov (United States)

Wu, Zhihua; Li, Kun; Zhan, Shaode; Tong, Ping; Li, Xin; Yang, Anshu; Chen, Hongbing

2017-09-14

Antibodies are used extensively in numerous applications both in vivo and in vitro. To purify anti-Ara h 2 polyclonal antibody, a homemade immunoaffinity chromatography (IAC) column method was established. The properties of homemade column were compared with those of the mAb affinity protein G (MPG) agarose high flow, a commercially available column successfully used in capturing polyclonal antibodies. During antibody purification from rabbits' antiserum against Ara h 2, the column capacity, recovery, and purification factor were characterized for IAC and MPG. The homemade IAC could separate the corresponding antibody with higher specificity and lower cost but with lower recovery and column capacity than those of MPG. Thus, the homemade IAC is a specific, inexpensive, and suitable method that can be used for various laboratory purifications.

A rapid and economic in-house DNA purification method using glass syringe filters.

Directory of Open Access Journals (Sweden)

Yun-Cheol Kim

Full Text Available BACKGROUND: Purity, yield, speed and cost are important considerations in plasmid purification, but it is difficult to achieve all of these at the same time. Currently, there are many protocols and kits for DNA purification, however none maximize all four considerations. METHODOLOGY/PRINCIPAL FINDINGS: We now describe a fast, efficient and economic in-house protocol for plasmid preparation using glass syringe filters. Plasmid yield and quality as determined by enzyme digestion and transfection efficiency were equivalent to the expensive commercial kits. Importantly, the time required for purification was much less than that required using a commercial kit. CONCLUSIONS/SIGNIFICANCE: This method provides DNA yield and quality similar to that obtained with commercial kits, but is more rapid and less costly.

Fractionation for Biodiesel Purification Using Supercritical Carbon Dioxide

Directory of Open Access Journals (Sweden)

Chao-Yi Wei

2014-02-01

Full Text Available In recent years, biodegradable and alternative biodiesel has attracted increased attention worldwide. Producing biodiesel from biomass involves critical separation and purification technology. Conventional technologies such as gravitational settling, decantation, filtration, water washing, acid washing, organic solvent washing and absorbent applications are inefficient, less cost effective and environmentally less friendly. In this study supercritical carbon dioxide (SC-CO2 with few steps and a low environmental impact, was used for biodiesel fractionation from impure fatty acid methyl ester (FAME solution mixes. The method is suitable for application in a variety of biodiesel production processes requiring subsequent stages of purification. The fractionation and purification was carried out using continuous SC-CO2 fractionation equipment, consisting of three columns filled with stainless steel fragments. A 41.85% FAME content solution mix was used as the raw material in this study. Variables were a temperature range of 40–70 °C, pressure range of 10–30 MPa, SC-CO2 flow rate range of 7–21 mL/min and a retention time range of 30–90 min. The Taguchi method was used to identify optimal operating conditions. The results show that a separated FAME content of 99.94% was verified by GC-FID under optimal fractionation conditions, which are a temperature of 40 °C of, a pressure level of 30MPa and a flow rate of 7 mL/min of SC-CO2 for a retention time of 90 min.

Uniform deposition of uranium hexafluoride (UF6): Standardized mass deposits and controlled isotopic ratios using a thermal fluorination method.

Science.gov (United States)

McNamara, Bruce K; O'Hara, Matthew J; Casella, Andrew M; Carter, Jennifer C; Addleman, R Shane; MacFarlan, Paul J

2016-07-01

We report a convenient method for the generation of volatile uranium hexafluoride (UF6) from solid uranium oxides and other U compounds, followed by uniform deposition of low levels of UF6 onto sampling coupons. Under laminar flow conditions, UF6 is shown to interact with surfaces within a fixed reactor geometry to a highly predictable degree. We demonstrate the preparation of U deposits that range between approximately 0.01 and 500ngcm(-2). The data suggest the method can be extended to creating depositions at the sub-picogramcm(-2) level. The isotopic composition of the deposits can be customized by selection of the U source materials and we demonstrate a layering technique whereby two U solids, each with a different isotopic composition, are employed to form successive layers of UF6 on a surface. The result is an ultra-thin deposit that bears an isotopic signature that is a composite of the two U sources. The reported deposition method has direct application to the development of unique analytical standards for nuclear safeguards and forensics. Further, the method allows access to very low atomic or molecular coverages of surfaces. Copyright © 2016 Elsevier B.V. All rights reserved.

Purification of alcohol obtained from molasses

Energy Technology Data Exchange (ETDEWEB)

Visnevskaya, G L; Egorov, A S; Sokol' skaya, E V

1960-01-01

A study of the composition of alcohol liquids on different plates of a fractionation column of indirect action during purification of alcohol obtained from normal and defective molasses, and from starch raw material, showed that there were two local strength minima in the lower part of the column and on the plates (adjacent and feed). Aldehydes behaved as a typical head impurity; a noticeable increase in their concentration occurred only on the highest plates in the fractionation column. In the zone of the column containing liquids of a strength of 86 to 94% alcohol by weight a sharply pronounced local maximum of ester accumulation were observed, provisionally designated as intermediate, whose presence is apparently one of the causes of the specific sharp taste of alcohol obtained from molasses. These esters hinder the obtaining of high-grade alcohols which are standard in respect to ester content and oxidizability test. Reduction with 0.05N KMnO/sub 4/ occurs most rapidly with alcohol liquids in the zone of ester accumulation; purification of alcohols obtained from grain and potato raw material resulted in no zones of ester accumulation in the column.

Combustion water purification techniques influence on OBT analysing using liquid scintillation counting method

International Nuclear Information System (INIS)

Varlam, C.; Vagner, I.; Faurescu, I.; Faurescu, D.

2015-01-01

In order to determine organically bound tritium (OBT) from environmental samples, these must be converted into water, measurable by liquid scintillation counting (LSC). For this purpose we conducted some experiments to determine OBT level of a grass sample collected from an uncontaminated area. The studied grass sample was combusted in a Parr bomb. However usual interfering phenomena were identified: color or chemical quench, chemiluminescence, overlap over tritium spectrum because of other radionuclides presence as impurities ( 14 C from organically compounds, 36 Cl as chloride and free chlorine, 40 K as potassium cations) and emulsion separation. So the purification of the combustion water before scintillation counting appeared to be essential. 5 purification methods were tested: distillation with chemical treatment (Na 2 O 2 and KMnO 4 ), lyophilization, chemical treatment (Na 2 O 2 and KMnO 4 ) followed by lyophilization, azeotropic distillation with toluene and treatment with a volcanic tuff followed by lyophilization. After the purification step each sample was measured and the OBT measured concentration, together with physico-chemical analysis of the water analyzed, revealed that the most efficient method applied for purification of the combustion water was the method using chemical treatment followed by lyophilization

Purification and characterization of protease enzyme from ...

African Journals Online (AJOL)

user

2013-03-20

Mar 20, 2013 ... Full Length Research Paper. Purification and ... ting into small peptides and free amino acids, which can ... Isolated strain was cultured in synthetic medium- casein (SMC; ... Protease activity was assayed by sigma's non-specific protease ... following buffers: 0.05 M citrate-phosphate buffer (pH 5 to 6), Tris-.

Expression and Purification of Sperm Whale Myoglobin

Science.gov (United States)

Miller, Stephen; Indivero, Virginia; Burkhard, Caroline

2010-01-01

We present a multiweek laboratory exercise that exposes students to the fundamental techniques of bacterial expression and protein purification through the preparation of sperm whale myoglobin. Myoglobin, a robust oxygen-binding protein, contains a single heme that gives the protein a reddish color, making it an ideal subject for the teaching…

Item Purification Does Not Always Improve DIF Detection: A Counterexample with Angoff's Delta Plot

Science.gov (United States)

Magis, David; Facon, Bruno

2013-01-01

Item purification is an iterative process that is often advocated as improving the identification of items affected by differential item functioning (DIF). With test-score-based DIF detection methods, item purification iteratively removes the items currently flagged as DIF from the test scores to get purified sets of items, unaffected by DIF. The…

Addressing the medicinal chemistry bottleneck: a lean approach to centralized purification.

Science.gov (United States)

Weller, Harold N; Nirschl, David S; Paulson, James L; Hoffman, Steven L; Bullock, William H

2012-09-10

The use of standardized lean manufacturing principles to improve drug discovery productivity is often thought to be at odds with fostering innovation. This manuscript describes how selective implementation of a lean optimized process, in this case centralized purification for medicinal chemistry, can improve operational productivity and increase scientist time available for innovation. A description of the centralized purification process is provided along with both operational and impact (productivity) metrics, which indicate lower cost, higher output, and presumably more free time for innovation as a result of the process changes described.

Refurbishment of uranium hexafluoride cylinder storage yards C-745-K, L, M, N, and P and construction of a new uranium hexafluoride cylinder storage yard (C-745-T) at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

International Nuclear Information System (INIS)

1996-07-01

The Paducah Gaseous Diffusion Plant (PGDP) is a uranium enrichment facility owned by the US Department of Energy (DOE). A residual of the uranium enrichment process is depleted uranium hexafluoride (UF6). Depleted UF6, a solid at ambient temperature, is stored in 32,200 steel cylinders that hold a maximum of 14 tons each. Storage conditions are suboptimal and have resulted in accelerated corrosion of cylinders, increasing the potential for a release of hazardous substances. Consequently, the DOE is proposing refurbishment of certain existing yards and construction of a new storage yard. This environmental assessment (EA) evaluates the impacts of the proposed action and no action and considers alternate sites for the proposed new storage yard. The proposed action includes (1) renovating five existing cylinder yards; (2) constructing a new UF6 storage yard; handling and onsite transport of cylinders among existing yards to accommodate construction; and (4) after refurbishment and construction, restacking of cylinders to meet spacing and inspection requirements. Based on the results of the analysis reported in the EA, DOE has determined that the proposed action is not a major Federal action that would significantly affect the quality of the human environment within the context of the National Environmental Policy Act of 1969. Therefore, DOE is issuing a Finding of No Significant Impact. Additionally, it is reported in this EA that the loss of less than one acre of wetlands at the proposed project site would not be a significant adverse impact

Refurbishment of uranium hexafluoride cylinder storage yards C-745-K, L, M, N, and P and construction of a new uranium hexafluoride cylinder storage yard (C-745-T) at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The Paducah Gaseous Diffusion Plant (PGDP) is a uranium enrichment facility owned by the US Department of Energy (DOE). A residual of the uranium enrichment process is depleted uranium hexafluoride (UF6). Depleted UF6, a solid at ambient temperature, is stored in 32,200 steel cylinders that hold a maximum of 14 tons each. Storage conditions are suboptimal and have resulted in accelerated corrosion of cylinders, increasing the potential for a release of hazardous substances. Consequently, the DOE is proposing refurbishment of certain existing yards and construction of a new storage yard. This environmental assessment (EA) evaluates the impacts of the proposed action and no action and considers alternate sites for the proposed new storage yard. The proposed action includes (1) renovating five existing cylinder yards; (2) constructing a new UF6 storage yard; handling and onsite transport of cylinders among existing yards to accommodate construction; and (4) after refurbishment and construction, restacking of cylinders to meet spacing and inspection requirements. Based on the results of the analysis reported in the EA, DOE has determined that the proposed action is not a major Federal action that would significantly affect the quality of the human environment within the context of the National Environmental Policy Act of 1969. Therefore, DOE is issuing a Finding of No Significant Impact. Additionally, it is reported in this EA that the loss of less than one acre of wetlands at the proposed project site would not be a significant adverse impact.

Antimicrobial biosurfactants from marine Bacillus circulans: extracellular synthesis and purification.

Science.gov (United States)

Mukherjee, S; Das, P; Sivapathasekaran, C; Sen, R

2009-03-01

To purify the biosurfactant produced by a marine Bacillus circulans strain and evaluate the improvement in surface and antimicrobial activities. The study of biosurfactant production by B. circulans was carried out in glucose mineral salts (GMS) medium using high performance thin layer chromatography (HPTLC) for quantitative estimation. The biosurfactant production by this strain was found to be growth-associated showing maximum biosurfactant accumulation at 26 h of fermentation. The crude biosurfactants were purified using gel filtration chromatography with Sephadex G-50 matrix. The purification attained by employing this technique was evident from UV-visible spectroscopy and TLC analysis of crude and purified biosurfactants. The purified biosurfactants showed an increase in surface activity and a decrease in critical micelle concentration values. The antimicrobial action of the biosurfactants was also enhanced after purification. The marine B. circulans used in this study produced biosurfactants in a growth-associated manner. High degree of purification could be obtained by using gel filtration chromatography. The purified biosurfactants showed enhanced surface and antimicrobial activities. The antimicrobial biosurfactant produced by B. circulans could be effectively purified using gel filtration and can serve as new potential drugs in antimicrobial chemotherapy.

Extraction, Separation, and Purification of Blueberry Anthocyanin Using Ethyl Alcohol

Directory of Open Access Journals (Sweden)

Zhe Gao

2017-11-01

Full Text Available Blueberry contains many substances that are important to the human body and can prevent cardiovascular diseases, protect the retina, and soften blood vessels. Anthocyanin, which is extracted from blueberry, can activate the retina, strengthen vision, reduce serum cholesterol, triglyceride and high-density lipoprotein, and protect cell nucleus tissues from radical oxidation; hence, blueberry is of importance to scientists from different countries. In this study, anthocyanin was extracted and separated from blueberry using ethyl alcohol to investigate the effects of factors, such as ethyl alcohol volume ratio on anthocyanin extraction and separation technologies. The extracting solution was then purified using the macroreticular resin purification method to investigate the effects of ethyl alcohol concentration and eluent dosage on anthocyanin extraction during purification. The research results demonstrated that 60 % ethyl alcohol volume fraction, 1 : 10 mass ratio of solid to liquid, and 60 °C ultrasonic temperature were the best conditions for anthocyanin extraction. The best purification conditions were 95 % ethyl alcohol, which had been acidized by 0.3 % hydrochloric acid and 70 ml of eluent. This work provides a reference for the application of ethyl alcohol in anthocyanin extraction.

Biomimetic small peptide functionalized affinity monoliths for monoclonal antibody purification.

Science.gov (United States)

Wang, Xiangyu; Xia, Donghai; Han, Hai; Peng, Kun; Zhu, Peijie; Crommen, Jacques; Wang, Qiqin; Jiang, Zhengjin

2018-08-09

The rapid development of monoclonal antibodies (mAbs) in therapeutic and diagnostic applications has necessitated the advancement of mAbs purification technologies. In this study, a biomimetic small peptide ligand 3,5-di-tert-butyl-4-hydroxybenzoic acid-Arg-Arg-Gly (DAAG) functionalized monolith was fabricated through a metal ion chelation-based multi-step approach. The resulting monolith showed good chromatographic performance. Compared with the Ni 2+ based IMAC monolith, the DAAG functionalized monolith exhibited not only excellent specificity but also higher dynamic binding capacity (DBC). The 10% DBC and 50% DBC for hIgG reached as high values as 26.0 and 34.6 mg/mL, respectively, at a ligand density of 8.8 μmol/mL, due to the high porosity and accessibility of the monolithic matrix. Moreover, the stability of the DAAG functionalized monolith in successive breakthrough experiments indicates that it has a promising potential for long-term use in mAbs purification. Finally, the DAAG functionalized monolith was successfully applied to the purification of trastuzumab or human immunoglobulin G (hIgG) from biological samples. Copyright © 2018 Elsevier B.V. All rights reserved.

Undulative induction electron accelerator for the waste and natural water purification systems

CERN Document Server

Kulish, Victor V; Gubanov, I V

2001-01-01

The project analysis of Undulative Induction Accelerator (EH - accelerator) for the waste and natural water purification systems is accomplished. It is shown that the use of the four-channel design of induction block and the standard set of auxiliary equipment (developed earlier for the Linear Induction Accelerators - LINACs) allow to construct commercially promising purification systems. A quality analysis of the accelerator is done and the optimal parameters are chosen taking into account the specific sphere of its usage.

Purification of β-acetylglucosaminase and β-galactosidase from ram testis

Science.gov (United States)

Caygill, J. C.; Roston, Christine P. J.; Jevons, F. R.

1966-01-01

1. The presence of β-galactosidase (EC 3.2.1.23) in an acetic acid extract of ram testis is reported. Some properties of the crude enzyme preparation were studied. 2. The purification of β-acetylglucosaminase (EC 3.2.1.30) and of β-galactosidase from the ram-testis extract by ammonium sulphate precipitation and chromatography on a CM-cellulose column is described. 3. The final purifications of the separated enzymes achieved were for the β-acetylglucosaminase 35 times and for the β-galactosidase 99 times. 4. The possibility of using DEAE-cellulose and Sephadex G-200 to purify the enzymes was investigated. PMID:5949569

Containment and storage of uranium hexafluoride at US Department of Energy uranium enrichment plants

International Nuclear Information System (INIS)

Barlow, C.R.; Alderson, J.H.; Blue, S.C.; Boelens, R.A.; Conkel, M.E.; Dorning, R.E.; Ecklund, C.D.; Halicks, W.G.; Henson, H.M.; Newman, V.S.; Philpot, H.E.; Taylor, M.S.; Vournazos, J.P.; Pryor, W.A.; Ziehlke, K.T.

1992-07-01

Isotopically depleted UF 6 (uranium hexafluoride) accumulates at a rate five to ten times greater than the enriched product and is stored in steel vessels at the enrichment plant sites. There are approximately 55,000 large cylinders now in storage at Paducah, Kentucky; Portsmouth, Ohio; and Oak Ridge, Tennessee. Most of them contain a nominal 14 tons of depleted UF 6 . Some of these cylinders have been in the unprotected outdoor storage environment for periods approaching 40 years. Storage experience, supplemented by limited corrosion data, suggests a service life of about 70 years under optimum conditions for the 48-in. diameter, 5/16-in.-wall pressure vessels (100 psi working pressure), using a conservative industry-established 1/4-in.-wall thickness as the service limit. In the past few years, however, factors other than atmospheric corrosion have become apparent that adversely affect the serviceability of small numbers of the storage containers and that indicate the need for a managed program to ensure maintenance ofcontainment integrity for all the cylinders in storage. The program includes periodic visual inspections of cylinders and storage yards with documentation for comparison with other inspections, a group of corrosion test programs to permit cylinder life forecasts, and identification of (and scheduling for remedial action) situations in which defects, due to handling damage or accelerated corrosion, can seriously shorten the storage life or compromise the containment integrity of individual cylinders. The program also includes rupture testing to assess the effects of certain classes of damage on overall cylinder strength, aswell as ongoing reviews of specifications, procedures, practices, and inspection results to effect improvements in handling safety, containment integrity, and storage life

Utilization of internal purification rejects; Sisaeisen puhdistuksen rejektikonsentraattien kelvollistaminen - KLT 02

Energy Technology Data Exchange (ETDEWEB)

Manner, H.; Nissen, M.

1998-12-31

This was a preliminary study which is part of a larger programme. The aim of the programme is to determine the properties and process ability of the concentrates which come from the internal purification of waters from the papermaking process. It is very important to know the properties and process ability of these purification concentrates in order to find the best methods of separating, reprocessing and utilizing them. The objective of this preliminary study was to ascertain the basic properties of these internal purification concentrates. It was also of interest to analyse the properties of papermaking waters and the state of internal purification today in paper mills. The state of papermaking waters and their internal purification were clarified by a literature review and by analyses of different types of waters. It was found that in mechanical pulping organic dissolved and colloidal substances were present in the water. Also there was a lot of dissolved and colloidal substances in waters from machines producing wood-containing paper grades. The salt content and chemical oxygen demand are critical values concerning the reuse of circulation waters. In mechanical pulping the convection of dissolved and colloidal substances to the paper machine can be reduced by the washing stage. Thus, the amount of dissolved and colloidal substances in the paper machine circulation waters can be reduced. In a paper machine, a disk filter removes fibers and fines from the circulation waters, but dissolved and colloidal substances are not removed. Also the properties of different kind of membrane filtration concentrates were analyzed. The total residue of membrane concentrates is low. For example, they can not be burned purely. The chemical oxygen demand of membrane concentrates is high. The most important subjects for further investigation are the improvement of fractionation and condensability. Furthermore procedures must be found to lower the chemical oxygen demand. One

Utilization of internal purification rejects; Sisaeisen puhdistuksen rejektikonsentraattien kelvollistaminen - KLT 02

Energy Technology Data Exchange (ETDEWEB)

Manner, H; Nissen, M

1999-12-31

This was a preliminary study which is part of a larger programme. The aim of the programme is to determine the properties and process ability of the concentrates which come from the internal purification of waters from the papermaking process. It is very important to know the properties and process ability of these purification concentrates in order to find the best methods of separating, reprocessing and utilizing them. The objective of this preliminary study was to ascertain the basic properties of these internal purification concentrates. It was also of interest to analyse the properties of papermaking waters and the state of internal purification today in paper mills. The state of papermaking waters and their internal purification were clarified by a literature review and by analyses of different types of waters. It was found that in mechanical pulping organic dissolved and colloidal substances were present in the water. Also there was a lot of dissolved and colloidal substances in waters from machines producing wood-containing paper grades. The salt content and chemical oxygen demand are critical values concerning the reuse of circulation waters. In mechanical pulping the convection of dissolved and colloidal substances to the paper machine can be reduced by the washing stage. Thus, the amount of dissolved and colloidal substances in the paper machine circulation waters can be reduced. In a paper machine, a disk filter removes fibers and fines from the circulation waters, but dissolved and colloidal substances are not removed. Also the properties of different kind of membrane filtration concentrates were analyzed. The total residue of membrane concentrates is low. For example, they can not be burned purely. The chemical oxygen demand of membrane concentrates is high. The most important subjects for further investigation are the improvement of fractionation and condensability. Furthermore procedures must be found to lower the chemical oxygen demand. One

Design of a nitrogen purification system with cryogenic method for neutrino detection.

Science.gov (United States)

Peng, Zhang; Zhongjun, Hu; Bingming, Wang; Qing, Li

2018-04-04

In order to detect the neutrino with liquid scintillation detector, high-purity nitrogen is essential for gas stripping in this detector. Therefore, it is necessary to design a purification system for the detector to purify nitrogen. Using the method of low temperature adsorption for the purification system, the key designs including the flow path, the adsorber and the selection of activated carbon, are introduced in this study. In these designs, the selection of activated carbon is the most important because the adsorption characteristic of the carbon is related to the performance of the purification system. The method of grand canonical ensemble Monte Carlo is adopted to simulate the adsorption of radon by the activated carbon with its slit pore model. Using this method, the working temperature and the key characteristic of the activated carbon are obtained. Copyright © 2018 Elsevier Ltd. All rights reserved.

Purification of plant plasma membranes by two-phase partitioning and measurement of H+ pumping.

Science.gov (United States)

Lund, Anette; Fuglsang, Anja Thoe

2012-01-01

Purification of plasma membranes by two-phase partitioning is based on the separation of microsomal membranes, dependent on their surface hydrophobicity. Here we explain the purification of plasma membranes from a relatively small amount of material (7-30 g). The fluorescent probe ACMA (9-amino-6-chloro-2-metoxyacridine) accumulates inside the vesicles upon protonation. Quenching of ACMA in the solution corresponds to the H(+) transport across the plasma membrane. Before running the assay, the plasma membranes are incubated with the detergent Brij-58 in order to create inside-out vesicles.Purification of plasma membranes by two-phase partitioning is based on the separation of microsomal membranes, dependent on their surface hydrophobicity. Here we explain the purification of plasma membranes from a relatively small amount of material (7-30 g). The fluorescent probe ACMA (9-amino-6-chloro-2-metoxyacridine) accumulates inside the vesicles upon protonation. Quenching of ACMA in the solution corresponds to the H(+) transport across the plasma membrane. Before running the assay, the plasma membranes are incubated with the detergent Brij-58 in order to create inside-out vesicles.

Industrial compatible re-growth of vertically aligned multiwall carbon nanotubes by ultrafast pure oxygen purification process

DEFF Research Database (Denmark)

Bu, Ian Y.Y.; Hou, Kai; Engstrøm, Daniel Southcott

2011-01-01

amorphous carbon and reactivate nickel catalyst. Controlling of the purification temperature is important for high yield CNTs, as excessive high annealing temperature results in deformation of the CNTs. Unlike hazardous wet purification treatments, purified CNTs remained vertically aligned and offer......Reproducible high-yield purification process of multiwalled carbon nanotubes (CNTs) was developed by thermal annealing in ultrapure oxygen. The optimized condition involves thermal annealing via a PID controlled heater in high purity oxygen at temperature of 450°C for 180s, which burns out...

[Purification of arsenic-binding proteins in hamster plasma after oral administration of arsenite].

Science.gov (United States)

Wang, Wenwen; Zhang, Min; Li, Chunhui; Qin, Yingjie; Hua, Naranmandura

2013-01-01

To purify the arsenic-binding proteins (As-BP) in hamster plasma after a single oral administration of arsenite (iAs(III)). Arsenite was given to hamsters in a single dose. Three types of HPLC columns, size exclusion, gel filtration and anion exchange columns, combined with an inductively coupled argon plasma mass spectrometer (ICP MS) were used to purify the As-BP in hamster plasma. SDS-PAGE was used to confirm the arsenic-binding proteins at each purification step. The three-step purification process successfully separated As-BP from other proteins (ie, arsenic unbound proteins) in hamster plasma. The molecular mass of purified As-BP in plasma was approximately 40-50 kD on SDS-PAGE. The three-step purification method is a simple and fast approach to purify the As-BP in plasma samples.

Chromatographic techniques used in the laboratory scale fractionation and purification of plasma

International Nuclear Information System (INIS)

Siti Najila Mohd Janib; Wan Hamirul Bahrin Wan Kamal; Shaharuddin Mohd

2004-01-01

Chromatography is a powerful technique used in the separation as well as purification of proteins for use as biopharmaceuticals or medicines. Scientists use many different chromatographic techniques in biotechnology as they bring a molecule from its initial identification stage to the stage of it becoming a marketed product. The most commonly used of these techniques is liquid chromatography (1,C). This technique can be used to separate the target molecule from undesired contaminants, as well as to analyse the final product for the requisite purity as established by governmental regulatory groups such as the FDA. Some examples of LC techniques include: ion exchange (IEC), hydrophobic interaction (HIC), gel filtration (GF), affinity (AC) and reverse phase (RPC) chromatography. These techniques are very versatile and can be used at any stage of the purification process i.e. capture, intermediate purification phase and polishing. The choice of a particular technique is dependent upon the nature of the target protein as well as its intended final use. This paper describes the preliminary work done on the chromatographic purification of factor VIII (FVIII), factor IX (FIX), albumin and IgG from plasma. Results, in particular, in the isolation of albumin and IgG using IEC, have been promising. Preparation and production of cryoprecipitate to yield FVIII and FIX have also been successful. (Author)

Purification and characterization of protease from Bacillus cereus ...

African Journals Online (AJOL)

chitti

2013-09-16

Sep 16, 2013 ... Purification and characterization of protease from. Bacillus cereus SU12 isolated from oyster. Saccostrea cucullata. S. Umayaparvathi*, S. Meenakshi, M. Arumugam and T. Balasubramanian. Centre of Advanced Study in Marine Biology, Faculty of Marine Sciences, Annamalai University, Parangipettai - 608.

A simple method for purification of herpesvirus DNA

DEFF Research Database (Denmark)

Christensen, Laurids Siig; Normann, Preben

1992-01-01

A rapid and reliable method for purification of herpesvirus DNA from cell cultures is described. The method is based on the isolation of virus particles and/or nucleocapsids by differential centrifugation and exploits the solubilizing and denaturing capabilities of cesium trifluoroacetate during...

Natural gas purification using supported ionic liquid membrane

NARCIS (Netherlands)

Althuluth, M.A.M.; Overbeek, J.P.; Wees, H.J.; Zubeir, L.F.; Haije, W.G.; Berrouk, A.S.; Peters, C.J.; Kroon, M.C.

2015-01-01

This paper examines the possibility of the application of a supported ionic liquid membrane (SILM) for natural gas purification. The ionic liquid (IL) 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([emim][FAP]) was impregnated successfully in the ¿-alumina layer of a tubular

Purification-Free, Target-Selective Immobilization of a Protein from Cell Lysates.

Science.gov (United States)

Cha, Jaehyun; Kwon, Inchan

2018-02-27

Protein immobilization has been widely used for laboratory experiments and industrial processes. Preparation of a recombinant protein for immobilization usually requires laborious and expensive purification steps. Here, a novel purification-free, target-selective immobilization technique of a protein from cell lysates is reported. Purification steps are skipped by immobilizing a target protein containing a clickable non-natural amino acid (p-azidophenylalanine) in cell lysates onto alkyne-functionalized solid supports via bioorthogonal azide-alkyne cycloaddition. In order to achieve a target protein-selective immobilization, p-azidophenylalanine was introduced into an exogenous target protein, but not into endogenous non-target proteins using host cells with amber codon-free genomic DNAs. Immobilization of superfolder fluorescent protein (sfGFP) from cell lysates is as efficient as that of the purified sfGFP. Using two fluorescent proteins (sfGFP and mCherry), the authors also demonstrated that the target proteins are immobilized with a minimal immobilization of non-target proteins (target-selective immobilization). © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Purification of methanol dehydrogenase from mouth methylotrophic bacteria of tropical region

Directory of Open Access Journals (Sweden)

Waturangi, D.

2011-01-01

Full Text Available Aims: Purification of methanol dehydrogenase (MDH from methylotrophic bacteria was conducted to obtain pure enzyme for further research and industrial applications due to the enzyme’s unique activity that catalyzes oxidation of methanol as an important carbon source in methylotrophic bacteria.Methodology and Results: The enzyme was screened from methylotrophic bacteria isolated from human mouth. Purification of this enzyme was conducted using ammonium sulphate precipitation followed by cation exchange chromatography. Two types of media were used to produce the enzymes: luria broth and standard mineral salts media (MSM. MSM produced MDH with higher specific activity than LB. Specific activity was also increased along with the purification steps. Application of ammonium sulphate increased the purity of enzyme and was more effective for the enzyme produced in LB. Using sepharose increased the enzyme activity 10 -57 folds.Conclusion, significant and impact of this study: With this, ammonium sulphate precipitation coupled with single cation exchange chromatographic system has been proved to provide sufficient purified of methanol dehydrogenase from methylotrophic bacteria origin of human mouth with high specific activity for further application.

Implementation of the Sulfur Hexafluoride Technique in Costa Rica to Quantify Enteric Methane in Cattle

Directory of Open Access Journals (Sweden)

Johnny Montenegro Ballestero

2016-12-01

Full Text Available In order to implement, for the first time in Costa Rica, the sulfur hexafluoride (SF6 tracer technique to determine the enteric methane (CH4released by cattle consuming tropical forages, this study was carried out at the Universidad Tecnica Nacional, Atenas, from May to July 2013. This technique allows capturing and storing a sample of methane in a device placed over the animal. The implementation was done in two phases: confinement and grazing. In both phases, Jersey heifers were used. They were subjected to an adaptation phase prior to the collection of gas samples. Confinement diet consisted of transvala silopaca (Digitaria decumbens and Brachiaria brizantha. In the second phase B. decumbens was grazed. The three species had 35 days of regrowth without fertilization. The daily emission of methane per heifer in confinement was 147±7 g, and 17.3±1.1 g kg-1 DM consumed. During the grazing phase, heifers released 141±16 g of CH4 d-1, and 16.1±1.1 g of CH4 kg-1 DM of consumed grass was estimated. The emission factor (Ym: 4.9 ± 0.3% for the grazing phase was lower than that suggested by IPCC. It is concluded that this technique is suitable for use under similar conditions to those used in this research, and with the calculation of Ym it is possible to estimate with low uncertainty, the emission of enteric methane in cattle that should be used in the National Inventories Greenhouse Gases for the livestock sector in Costa Rica.

Large-scale functional purification of recombinant HIV-1 capsid.

Directory of Open Access Journals (Sweden)

Magdeleine Hung

Full Text Available During human immunodeficiency virus type-1 (HIV-1 virion maturation, capsid proteins undergo a major rearrangement to form a conical core that protects the viral nucleoprotein complexes. Mutations in the capsid sequence that alter the stability of the capsid core are deleterious to viral infectivity and replication. Recently, capsid assembly has become an attractive target for the development of a new generation of anti-retroviral agents. Drug screening efforts and subsequent structural and mechanistic studies require gram quantities of active, homogeneous and pure protein. Conventional means of laboratory purification of Escherichia coli expressed recombinant capsid protein rely on column chromatography steps that are not amenable to large-scale production. Here we present a function-based purification of wild-type and quadruple mutant capsid proteins, which relies on the inherent propensity of capsid protein to polymerize and depolymerize. This method does not require the packing of sizable chromatography columns and can generate double-digit gram quantities of functionally and biochemically well-behaved proteins with greater than 98% purity. We have used the purified capsid protein to characterize two known assembly inhibitors in our in-house developed polymerization assay and to measure their binding affinities. Our capsid purification procedure provides a robust method for purifying large quantities of a key protein in the HIV-1 life cycle, facilitating identification of the next generation anti-HIV agents.

Performance of the 0.3-meter transonic cryogenic tunnel with air, nitrogen, and sulfur hexafluoride media under closed loop automatic control

Science.gov (United States)

Balakrishna, S.; Kilgore, W. Allen

1995-01-01

The NASA Langley 0.3-m Transonic Cryogenic Tunnel was modified in 1994, to operate with any one of the three test gas media viz., air, cryogenic nitrogen gas, or sulfur hexafluoride gas. This document provides the initial test results with respect to the tunnel performance and tunnel control, as a part of the commissioning activities on the microcomputer based controller. The tunnel can provide precise and stable control of temperature to less than or equal to +/- 0.3 K in the range 80-320 K in cyro mode or 300-320 K in air/SF6 mode, pressure to +/- 0.01 psia in the range 15-88 psia and Mach number to +/- O.0015 in the range 0.150 to transonic Mach numbers up to 1.000. A new heat exchanger has been included in the tunnel circuit and is performing adequately. The tunnel airfoil testing benefits considerably by precise control of tunnel states and helps in generating high quality aerodynamic test data from the 0.3-m TCT.

An improved method for purification of recombinant truncated heme oxygenase-1 by expanded bed adsorption and gel filtration.

Science.gov (United States)

Hu, Hong-Bo; Wang, Wei; Han, Ling; Zhou, Wen-Pu; Zhang, Xue-Hong

2007-03-01

Recombinant truncated human heme oxygenase-1 (hHO-1) expressed in Escherichia coli was efficiently separated and purified from feedstock by DEAE-ion exchange expanded bed adsorption. Protocol optimization of hHO-1 on DEAE adsorbent resulted in adsorption in 0 M NaCl and elution in 150 mM NaCl at a pH of 8.5. The active enzyme fractions separated from the expanded bed column were further purified by a Superdex 75 gel filtration step. The specific hHO-1 activity increased from 0.82 +/- 0.05 to 24.8 +/- 1.8 U/mg during the whole purification steps. The recovery and purification factor of truncated hHO-1 of the whole purification were 72.7 +/- 4.7 and 30.2 +/- 2.3%, respectively. This purification process can decrease the demand on the preparation of feedstock and simplify the purification process.

Optimization of mass flow rate in RGTT200K coolant purification for Carbon Monoxide conversion process

International Nuclear Information System (INIS)

Sumijanto; Sriyono

2016-01-01

Carbon monoxide is a species that is difficult to be separated from the reactor coolant helium because it has a relatively small molecular size. So it needs a process of conversion from carbon monoxide to carbondioxide. The rate of conversion of carbon monoxide in the purification system is influenced by several parameters including concentration, temperature and mass flow rate. In this research, optimization of the mass flow rate in coolant purification of RGTT200K for carbon monoxide conversion process was done. Optimization is carried out by using software Super Pro Designer. The rate of reduction of reactant species, the growth rate between the species and the species products in the conversion reactions equilibrium were analyzed to derive the mass flow rate optimization of purification for carbon monoxide conversion process. The purpose of this study is to find the mass flow rate of purification for the preparation of the basic design of the RGTT200K coolant helium purification system. The analysis showed that the helium mass flow rate of 0.6 kg/second resulted in an un optimal conversion process. The optimal conversion process was reached at a mass flow rate of 1.2 kg/second. A flow rate of 3.6 kg/second – 12 kg/second resulted in an ineffective process. For supporting the basic design of the RGTT200K helium purification system, the mass flow rate for carbon monoxide conversion process is suggested to be 1.2 kg/second. (author)

Purification of bacteriocins using size-exclusion chromatography

Directory of Open Access Journals (Sweden)

Vivek K. Bajpai

2016-06-01

Full Text Available The bacteriocin purification involves following main steps. a. Extraction of cell-free-supernatant of bacteria. b. Ammonium sulfate precipitation. c. Dialysis. d. Diafiltration using PVP and e. Size-exclusion chromatography. However, depending on the nature of work, the compound could be further analyzed by reverse-phase HPLC, NMR, mass spectrometry and sequencing.

Purification of bacteriocins produced by lactic acid bacteria.

Science.gov (United States)

Saavedra, Lucila; Castellano, Patricia; Sesma, Fernando

2004-01-01

Bacteriocins are antibacterial substances of a proteinaceous nature that are produced by different bacterial species. Lactic acid bacteria (LAB) produce biologically active peptides or protein complexes that display a bactericidal mode of action almost exclusively toward Gram-positive bacteria and particularly toward closely related species. Generally they are active against food spoilage and foodborne pathogenic microorganisms including Bacillus cereus, Clostridium perfringens, Staphylococcus aureus, and Listeria monocytogenes. There is an increased tendency to use natural occurring metabolites to prevent the growth of undesirable flora in foodstuffs. These metabolites could replace the use of chemical additives such as sorbic acid, sulfur dioxide, nitrite, nitrate, and others. For instance, bacteriocins produced by LAB may be promising for use as bio-preservaties. Bacteriocins of lactic acid bacteria are typically cationic, hydrophobic peptides and differ widely in many characteristics including molecular weight, presence of particular groups of amino acids, pI, net positive charge, and post-translational modifications of certain amino acids. This heterogeneity within the LAB bacteriocins may explain the different procedures for isolation and purification developed so far. The methods most frequently used for isolation, concentration, and purification involve salt precipitation of bacteriocins from culture supernatants, followed by various combinations of gel filtration, ion-exchange chromatography, and reverse-phase high-performance liquid chromatography (RP-HPLC). In this chapter, a protocol is described that combines several methods used in our laboratory for the purification of two cationic bacteriocins, Lactocin 705AL and Enterocin CRL10, produced by Lactobacillus casei CRL705 and Enterococcus mundtii CRL10, respectively.

Online Oxide Contamination Measurement and Purification Demonstration

Science.gov (United States)

Bradley, D. E.; Godfroy, T. J.; Webster, K. L.; Garber, A. E.; Polzin, K. A.; Childers, D. J.

2011-01-01

Liquid metal sodium-potassium (NaK) has advantageous thermodynamic properties indicating its use as a fission reactor coolant for a surface (lunar, martian) power system. A major area of concern for fission reactor cooling systems is system corrosion due to oxygen contaminants at the high operating temperatures experienced. A small-scale, approximately 4-L capacity, simulated fission reactor cooling system employing NaK as a coolant was fabricated and tested with the goal of demonstrating a noninvasive oxygen detection and purification system. In order to generate prototypical conditions in the simulated cooling system, several system components were designed, fabricated, and tested. These major components were a fully-sealed, magnetically-coupled mechanical NaK pump, a graphite element heated reservoir, a plugging indicator system, and a cold trap. All system components were successfully demonstrated at a maximum system flow rate of approximately 150 cc/s at temperatures up to 550 C. Coolant purification was accomplished using a cold trap before and after plugging operations which showed a relative reduction in oxygen content.

Rupture of Model 48Y UF6 cylinder and release of uranium hexafluoride, Sequoyah Fuels Facility, Gore, Oklahoma, January 4, 1986. Volume 1

International Nuclear Information System (INIS)

1986-02-01

At 11:30 a.m. on January 4, 1986, a Model 48Y UF 6 cylinder filled with uranium hexafluoride (UF 6 ) ruptured while it was being heated in a steam chest at the Sequoyah Fuels Conversion Facility near Gore, Oklahoma. One worker died because he inhaled hydrogen fluoride fumes, a reaction product of UF 6 and airborne moisture. Several other workers were injured by the fumes, but none seriously. Much of the facility complex and some offsite areas to the south were contaminated with hydrogen fluoride and a second reaction product, uranyl fluoride. The interval of release was approximately 40 minutes. The cylinder, which had been overfilled, ruptured while it was being heated because of the expansion of UF 6 as it changed from the solid to the liquid phase. The maximum safe capacity for the cylinder is 27,560 pounds of product. Evidence indicates that it was filled with an amount exceeding this limit. 18 figs

Increase of COP for heat transformer in water purification systems. Part II - Without increasing heat source temperature

International Nuclear Information System (INIS)

Romero, R.J.; Siqueiros, J.; Huicochea, A.

2007-01-01

The integration of a water purification system allows a heat transformer to increase the actual coefficient of performance, by the reduction of the amount of heat supplied by unit of heat. A new defined COP called COP WP is proposed for the present system, which considers the fraction of heat recycled. Simulation with proven software compares the performance of the modeling of an absorption heat transformer for water purification (AHTWP) operating with water/lithium bromide, as working fluid-absorbent pair. Plots of enthalpy-based coefficients of performance (COP ET ) and water purification coefficient of performance (COP WP ) are shown against absorber temperature for several thermodynamic operating conditions. The results showed that the proposed (AHTWP) system is capable of increasing the original value of COP ET up to 1.6 times its original value by recycling energy from a water purification system. The proposed COP WP allows increments for COP values from any experimental data for water purification or for any other distillation system integrated to a heat transformer, regardless of actual COP A value or working fluid-absorbent pair

Development of the protocol for purification of artemisinin based on combination of commercial and computationally designed adsorbents.

Science.gov (United States)

Piletska, Elena V; Karim, Kal; Cutler, Malcolm; Piletsky, Sergey A

2013-01-01

A polymeric adsorbent for extraction of the antimalarial drug artemisinin from Artemisia annua L. was computationally designed. This polymer demonstrated a high capacity for artemisinin (120 mg g(-1) ), quantitative recovery (87%) and was found to be an effective material for purification of artemisinin from complex plant matrix. The artemisinin quantification was conducted using an optimised HPLC-MS protocol, which was characterised by high precision and linearity in the concentration range between 0.05 and 2 μg mL(-1) . Optimisation of the purification protocol also involved screening of commercial adsorbents for the removal of waxes and other interfering natural compounds, which inhibit the crystallisation of artemisinin. As a result of a two step-purification protocol crystals of artemisinin were obtained, and artemisinin purity was evaluated as 75%. By performing the second stage of purification twice, the purity of artemisinin can be further improved to 99%. The developed protocol produced high-purity artemisinin using only a few purification steps that makes it suitable for large scale industrial manufacturing process. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Combustion water purification techniques influence on OBT analysing using liquid scintillation counting method

Energy Technology Data Exchange (ETDEWEB)

Varlam, C.; Vagner, I.; Faurescu, I.; Faurescu, D. [National Institute for Cryogenics and Isotopic Technologies, Valcea (Romania)

2015-03-15

In order to determine organically bound tritium (OBT) from environmental samples, these must be converted into water, measurable by liquid scintillation counting (LSC). For this purpose we conducted some experiments to determine OBT level of a grass sample collected from an uncontaminated area. The studied grass sample was combusted in a Parr bomb. However usual interfering phenomena were identified: color or chemical quench, chemiluminescence, overlap over tritium spectrum because of other radionuclides presence as impurities ({sup 14}C from organically compounds, {sup 36}Cl as chloride and free chlorine, {sup 40}K as potassium cations) and emulsion separation. So the purification of the combustion water before scintillation counting appeared to be essential. 5 purification methods were tested: distillation with chemical treatment (Na{sub 2}O{sub 2} and KMnO{sub 4}), lyophilization, chemical treatment (Na{sub 2}O{sub 2} and KMnO{sub 4}) followed by lyophilization, azeotropic distillation with toluene and treatment with a volcanic tuff followed by lyophilization. After the purification step each sample was measured and the OBT measured concentration, together with physico-chemical analysis of the water analyzed, revealed that the most efficient method applied for purification of the combustion water was the method using chemical treatment followed by lyophilization.

The Monitoring and Affinity Purification of Proteins Using Dual Tags with Tetracysteine Motifs

Science.gov (United States)

Giannone, Richard J.; Liu, Yie; Wang, Yisong

Identification and characterization of protein-protein interaction networks is essential for the elucidation of biochemical mechanisms and cellular function. Affinity purification in combination with liquid chromatography-tandem mass spectrometry (LC-MS/MS) has emerged as a very powerful tactic for the identification of specific protein-protein interactions. In this chapter, we describe a comprehensive methodology that uses our recently developed dual-tag affinity purification system for the enrichment and identification of mammalian protein complexes. The protocol covers a series of separate but sequentially related techniques focused on the facile monitoring and purification of a dual-tagged protein of interest and its interacting partners via a system built with tetracysteine motifs and various combinations of affinity tags. Using human telomeric repeat binding factor 2 (TRF2) as an example, we demonstrate the power of the system in terms of bait protein recovery after dual-tag affinity purification, detection of bait protein subcellular localization and expression, and successful identification of known and potentially novel TRF2 interacting proteins. Although the protocol described here has been optimized for the identification and characterization of TRF2-associated proteins, it is, in principle, applicable to the study of any other mammalian protein complexes that may be of interest to the research community.

High-level expression, purification, polyclonal antibody preparation ...

African Journals Online (AJOL)

OprD is a specific porin which can binds imipenem and carbapenems in Pseudomonas aeruginosa. OprD loss plays a central role in mediating carbapenem resistance. Therefore, purification of oprD protein lays a pavement for the study in vivo and in vitro. In our study, the oprD gene was cloned into pQE30 expression ...

Sodium tests on an integrated purification prototype for a sodium-cooled fast breeder reactor

International Nuclear Information System (INIS)

Abramson, R.

1984-04-01

This paper describes sodium tests performed on the integrated primary sodium purification prototype of the Creys Malville Super Phenix 1 fast breeder reactor. These tests comprised: - hydrostatic test, - thermal tests, - handling tests. They enabled a number of new technological arrangements to be qualified and provided the necessary information for the design and construction of the Super Phenix 1 purification units

Preparative Purification of Recombinant Proteins: Current Status and Future Trends

Directory of Open Access Journals (Sweden)

Mayank Saraswat

2013-01-01

Full Text Available Advances in fermentation technologies have resulted in the production of increased yields of proteins of economic, biopharmaceutical, and medicinal importance. Consequently, there is an absolute requirement for the development of rapid, cost-effective methodologies which facilitate the purification of such products in the absence of contaminants, such as superfluous proteins and endotoxins. Here, we provide a comprehensive overview of a selection of key purification methodologies currently being applied in both academic and industrial settings and discuss how innovative and effective protocols such as aqueous two-phase partitioning, membrane chromatography, and high-performance tangential flow filtration may be applied independently of or in conjunction with more traditional protocols for downstream processing applications.

Purification of simple substances by distillation with impurity hydrothermal oxidation

International Nuclear Information System (INIS)

Kalashnik, O.N.; Nisel'son, L.A.

1987-01-01

A possibility of applying distillation method in water vapours for purification of simple substances from impurities is studied. Based on thermodynamic analysis of interaction processes in E-H 2 O system, conducted using a computer, it is as certained that SS, Se, Te, As, Cd, Hg can be purified from the majority of the impurities analysed by distillation in a water vapour flow. Behaviour of Zn, C, Ge, Al, Sb characteristic impurities under cadmium, arsenic and tellurium distillation is studied. Experiments on cadmium, arsenic and tellurium purification have confirmed, that distillation with hydrothermal oxidation of Zn, C, Ge impurities sometimes appears to be a more effective method as compared to distillation in a hydrogen flow

One-step FPLC-size-exclusion chromatography procedure for purification of rDMBT1 6 kb with increased biological activity

DEFF Research Database (Denmark)

Tuttolomondo, Martina; Hansen, Pernille Lund; Mollenhauer, Jan

2018-01-01

from saliva or produced in vitro and purified by a multistep affinity purification procedure using bacteria, followed by FPLC. Here, we compared a simple, one-step FPLC-SEC protocol for purification of recombinant DMBT1 6 kb, with that of the standard bacteria affinity purification-based protocol. Our...

Purification and biochemical characterisation of the yeast ABC transporter Pdr11p

DEFF Research Database (Denmark)

Laub, Katrine Rude

Sterols constitute an essential lipid class in eukaryotic membranes where intracellular distributions are highly regulated. In the yeast Saccharomyces cerevisiae sterol uptake has been attributed to the two plasma membrane-localised ATP-binding cassette (ABC) transporters, Aus1p and Pdr11p...... of the yeast ABC transporter Pdr11p. This includes optimising its overexpression utilising the galactose induction system in S. cerevisiae, screening for the best detergent to extract the protein from the membrane, and establishing purification and reconstitution protocols. By providing a purification...

Reverse osmosis based water treatment and purification systems for nuclear power installations

International Nuclear Information System (INIS)

Epimakhov, V.N.; Olejnik, M.S.; Moskvin, L.N.

2004-01-01

Experiments on the realization and service of specialized water treatment and purification plants based on the principle of reverse osmosis filtration of water at the NPU benches of the A.P. Aleksandrov Scientific Research Technological Institute (SRTI) are analyzed. Membrane-sorption unit including module of micro-, ultrafiltration, reverse osmosis and ion exchange with productivity to 0.5 m 3 /h is developed and operated at SRTI. It is demonstrated that reverse osmosis purification of manufacturing water significantly improves service conditions of NPU and decreases salinity [ru

Future of antibody purification.

Science.gov (United States)

Low, Duncan; O'Leary, Rhona; Pujar, Narahari S

2007-03-15

Antibody purification seems to be safely ensconced in a platform, now well-established by way of multiple commercialized antibody processes. However, natural evolution compels us to peer into the future. This is driven not only by a large, projected increase in the number of antibody therapies, but also by dramatic improvements in upstream productivity, and process economics. Although disruptive technologies have yet escaped downstream processes, evolution of the so-called platform is already evident in antibody processes in late-stage development. Here we perform a wide survey of technologies that are competing to be part of that platform, and provide our [inherently dangerous] assessment of those that have the most promise.

Purification of radionuclides for nuclear medicine

International Nuclear Information System (INIS)

Horwitz, E.P.; Bond, A.H.

2002-01-01

Novel systems for the rapid separation of 67 Cu, 90 Y, 188 Re, 212 Bi, 213 Bi, and 223 Ra are described. To achieve the high levels of decontamination required of radionuclides used in radioimmunotherapy, we have utilised combinations of ion exchange (IX) and novel extraction chromatographic (EXC) resins. The objective of each separation system is to remove by many orders of magnitude the parent isotopes and to reduce the concentrations of stable, sometimes adventitious impurities, to low levels. The latter objective is particularly important to achieve a high degree of bonding of radionuclide onto a monoclonal antibody. The purification of 212 Bi (60.6 min half-life) furnishes a good example of the level of purity that we have achieved using tandem combinations of EXC and IX resins. Bismuth-212 was separated from its daughters, 212 Pb, 224 Ra, 228 Th and 232 U at the 50 mCi level. The resultant 212 Bi decayed to background in a few days indicative of high purity. Another example of extraordinary removal of parent nuclide from daughter nuclide and subsequent purification of daughter from stable elements is the preparation of 90 Y. Strontium-90 was removed from 90 Y by > 10 9 . The purified 90 Y uptake by monoclonal antibodies was close to 100%

Modelling a water purification process for quality monitoring

NARCIS (Netherlands)

Meulen, van der F.H.; Luca, S.; Overal, G.; Dubbeldam, J.L.A.; Di Bucchianico, A.; Jongbloed, G.; Dubbeldam, J.; Groenevelt, W.; Heemink, A.W.; Lahaye, D.; Meerman, C.; Meulen, van der F.

2014-01-01

This paper deals with a quality engineering problem introduced by ‘Waterlaboratorium Noord’ (WLN) situated at the Netherlands. In-terest lies in determining an optimal sampling frequency that provides suÿcient information on the water quality in a drinking water purifica-tion plant. The water

Commercial ampholytes used for isoelectric focusing may interfere with bioactivity based purification of antimicrobial peptides

OpenAIRE

Riazi, Shadi; Dover, Sara; Turovskiy, Yevgeniy; Chikindas, Michael L.

2007-01-01

BioRad's Rotofor® system has been frequently used for the purification of proteins and smaller peptides such as bacteriocins. In this study, we report that some commercially available ampholytes used with the Rotofor® isoelectric focusing system possess antimicrobial activity, which may interfere with the purification of bacteriocins and bacteriocin-like substances.

Development of Nano-hybrid Cellulose Acetate/TiO2 Membrane for Eugenol Purification from Crude Clove Leaf Oil

Directory of Open Access Journals (Sweden)

Kusworo Tutuk Djoko

2018-01-01

Full Text Available Chemical separation and purification are the important part of the chemical industry which consumes up to 70% energy cost. The separation technology such as distillation and absorption are well known in essential oil purification. The purification of clove leaf oil needs an attention because the current technology still consumes high energy and produces chemical wastes. The employment of membrane separation for clove leaf purification is a novel concept that needs many improvements. The main problem of polymeric membrane utilization is eugenol ability to dissolve the polymer membrane. Cellulose acetate is one of membrane polymers that is insoluble in eugenol. This paper reveals the performance of nanohybrid CA/TiO2 membrane for eugenol purification. The stability of produced membrane as an organic solvent nanofiltration (OSN is evaluated in this study. The SEM image result shows that fabricated membrane has an asymmetric structure of membrane sub-layer. The different nano-particles loading shows the variation of permeate fluxes, the increase of nano-particles in polymer blend tends to increase the permeability. Thus, this study provides an overview of the potential CA/TiO2 for OSN development by incorporating inorganic nano-particles in membrane polymers for eugenol purification that can be integrated in upstream separation process.

Anti-HSV-1 activity in vitro of extracellular polysaccharides purification of Paecilomyces lilacinus on isolated from Hainan mangrove

Directory of Open Access Journals (Sweden)

Yong-Xia Wang

2016-10-01

Full Text Available Objective: To explore the antiviral activity on HSV-1 of the extracellular polysaccharides (EPS purification of Paecilomyces lilacinus (P. lilacinus isolated from mangrove in Hainan province. Methods: The toxicity of the EPS purification on Vero cells and its anti-HSV-1 activity were assessed by cytopathic effect(CPE and MTT assay. The Vero cells survival rates, HSV-1 inhibition rates by the purification and virus titer were calculated. Results: The purification showed little cytotoxic effect on Vero with a CC50 value of 735.49 µg/mL. It could inhibit HSV-1 absorption on Vero cells, and there was a significant difference (P<0.01 compared with control group (virus group, and the highest inhibition ratio was 35.0% at dose of 400 µg/mL; The biosynthesis of HSV-1 could be inhibited by the extract with dose-dependent manner, and the IC50 value to the viruses was 387.26 µg/mL, and the highest inhibition ratio was 61.3% at dose of 400 µg/mL; but the purification couldn’t inactivate HSV-1 directly. Conclusion: The EPS purification had certain antiviral effect, it could inhibit HSV-1 absorption and biosynthesis with a dose effect relationship.

Electrochemical alkaline Fe(VI) water purification and remediation.

Science.gov (United States)

Licht, Stuart; Yu, Xingwen

2005-10-15

Fe(VI) is an unusual and strongly oxidizing form of iron, which provides a potentially less hazardous water-purifying agent than chlorine. A novel on-line electrochemical Fe(VI) water purification methodology is introduced. Fe(VI) addition had been a barrier to its effective use in water remediation, because solid Fe(VI) salts require complex (costly) syntheses steps and solutions of Fe(VI) decompose. Online electrochemical Fe(VI) water purification avoids these limitations, in which Fe(VI) is directly prepared in solution from an iron anode as the FeO42- ion, and is added to the contaminant stream. Added FeO42- decomposes, by oxidizing a wide range of water contaminants including sulfides (demonstrated in this study) and other sulfur-containing compounds, cyanides (demonstrated in this study), arsenic (demonstrated in this study), ammonia and other nitrogen-containing compounds (previously demonstrated), a wide range of organics (phenol demonstrated in this study), algae, and viruses (each previously demonstrated).

Development of tantalum–zirconium alloy for hydrogen purification

Energy Technology Data Exchange (ETDEWEB)

Kumar, Sanjay, E-mail: sanjay.barc@gmail.com [Fusion Reactor Materials Section, MG, BARC, Mumbai 85 (India); IAMR, Hiroshima University, Higashihiroshima 739-8530 (Japan); Singh, Anamika [GSASM Hiroshima University, Higashihiroshima 739-8530 (Japan); Jain, Uttam; Dey, Gautam Kumar [Fusion Reactor Materials Section, MG, BARC, Mumbai 85 (India)

2016-11-01

Highlights: • Terminal solid solubility of Ta increases with Zr addition. • Increase in lattice parameters of Ta due to Zr addition may be the possible reason. • Enhance H solubility could also be explained on the change in e-DOS of Ta–Zr alloys. • Ta–Zr alloys could be possible combination for hydrogen purification membrane. - Abstract: Terminal solid solubility of hydrogen in Ta–Zr alloys has been studied in connection with the development of tantalum based metallic membrane for hydrogen/tritium purification. The alloys were prepared by vacuum arc melting technique and subsequently cold rolled to 0.2 mm thickness. The terminal solid solubility of hydrogen in these cold rolled samples was investigated in a modified Sieverts apparatus. The terminal solid solubility of hydrogen was marginally increased with zirconium content. The change in the lattices parameter of tantalum upon zirconium addition and the higher affinity of zirconium for hydrogen as compared to tantalum could be the possible reasons.

Purification and characterization of a thylakoid protein kinase

International Nuclear Information System (INIS)

Coughlan, S.J.; Hind, G.

1986-01-01

Control of state transitions in the thylakoid by reversible phosphorylation of the light-harvesting chlorophyll a/b protein complex of photosystem II (LHC-II) is modulated by a kinase. The kinase catalyzing this phosphorylation is associated with the thylakoid membrane, and is regulated by the redox state of the plastoquinone pool. The isolation and partial purification from spinach thylakoids of two protein kinases (CPK1, CPK2) of apparent molecular masses 25 kDa and 38 kDa has been reported. Neither enzyme utilizes isolated LHC-II as a substrate. The partial purification of a third protein kinase (LHCK) which can utilize both lysine-rich histones (IIIs and Vs) and isolated LHC-II as substrate has now been purified to homogeneity and characterized by SDS-polyacrylamide gel electrophoresis as a 64 kDa peptide. From a comparison of the two isolation procedures we have concluded that CPK1 is indeed a protein kinase, but has a lower specific activity than that of LHCK. 8 refs., 4 figs

The importance of the ammonia purification process in ammonia-water absorption systems

International Nuclear Information System (INIS)

Fernandez-Seara, Jose; Sieres, Jaime

2006-01-01

Practical experience in working with ammonia-water absorption systems shows that the ammonia purification process is a crucial issue in order to obtain an efficient and reliable system. In this paper, the detrimental effects of the residual water content in the vapour refrigerant are described and quantified based on the system design variables that determine the effectiveness of the purification process. The study has been performed considering a single stage system with a distillation column with complete condensation. The ammonia purification effectiveness of the column is analysed in terms of the efficiencies in the stripping and rectifying sections and the reflux ratio. By varying the efficiencies from 0 to 1, systems with neither the rectifying nor stripping section, with either the rectifying or stripping section, or with both sections can be considered. The impact of the ammonia purification process on the absorption system performance is studied based on the column efficiencies and reflux ratio; and its effects on refrigerant concentration, system COP, system pressures and main system mass flow rates and concentrations are analysed. When the highest efficiency rectifying sections are used a combination of generation temperature and reflux ratio which leads to optimum COP values is found. The analysis covers different operating conditions with air and water cooled systems from refrigeration to air conditioning applications by changing the evaporation temperature. The importance of rectification in each kind of application is evaluated

Generation and purification of human stem cell-derived cardiomyocytes

NARCIS (Netherlands)

Schwach, Verena; Passier, Robert

2016-01-01

© 2016 International Society of Differentiation Efficient and reproducible generation and purification of human stem cell-derived cardiomyocytes (CMs) is crucial for regenerative medicine, disease modeling, drug screening and study of developmental events during cardiac specification. Established

Comparative study of methods for extraction and purification of ...

African Journals Online (AJOL)

USER

2010-08-02

Aug 2, 2010 ... and or enzymatic lysis for direct or indirect extraction of. DNA followed by ... strength wastewater sludge in order to determine the best. DNA extraction protocol ... Ammonium acetate purification method was used to remove the.

Conductive diamond electrodes for water purification

Directory of Open Access Journals (Sweden)

Carlos Alberto Martínez-Huitle

2007-12-01

Full Text Available Nowadays, synthetic diamond has been studied for its application in wastewater treatment, electroanalysis, organic synthesis and sensor areas; however, its use in the water disinfection/purification is its most relevant application. The new electrochemistry applications of diamond electrodes open new perspectives for an easy, effective, and chemical free water treatment. This article highlights and summarizes the results of a selection of papers dealing with electrochemical disinfection using synthetic diamond films.

[Alcohol-purification technology and its particle sedimentation process in manufactory of Fufang Kushen injection].

Science.gov (United States)

Liu, Xiaoqian; Tong, Yan; Wang, Jinyu; Wang, Ruizhen; Zhang, Yanxia; Wang, Zhimin

2011-11-01

Fufang Kushen injection was selected as the model drug, to optimize its alcohol-purification process and understand the characteristics of particle sedimentation process, and to investigate the feasibility of using process analytical technology (PAT) on traditional Chinese medicine (TCM) manufacturing. Total alkaloids (calculated by matrine, oxymatrine, sophoridine and oxysophoridine) and macrozamin were selected as quality evaluation markers to optimize the process of Fufang Kushen injection purification with alcohol. Process parameters of particulate formed in the alcohol-purification, such as the number, density and sedimentation velocity, were also determined to define the sedimentation time and well understand the process. The purification process was optimized as that alcohol is added to the concentrated extract solution (drug material) to certain concentration for 2 times and deposited the alcohol-solution containing drug-material to sediment for some time, i.e. 60% alcohol deposited for 36 hours, filter and then 80% -90% alcohol deposited for 6 hours in turn. The content of total alkaloids was decreased a little during the depositing process. The average settling time of particles with the diameters of 10, 25 microm were 157.7, 25.2 h in the first alcohol-purified process, and 84.2, 13.5 h in the second alcohol-purified process, respectively. The optimized alcohol-purification process remains the marker compositions better and compared with the initial process, it's time saving and much economy. The manufacturing quality of TCM-injection can be controlled by process. PAT pattern must be designed under the well understanding of process of TCM production.

An automated synthesis-purification-sample-management platform for the accelerated generation of pharmaceutical candidates.

Science.gov (United States)

Sutherland, J David; Tu, Noah P; Nemcek, Thomas A; Searle, Philip A; Hochlowski, Jill E; Djuric, Stevan W; Pan, Jeffrey Y

2014-04-01

A flexible and integrated flow-chemistry-synthesis-purification compound-generation and sample-management platform has been developed to accelerate the production of small-molecule organic-compound drug candidates in pharmaceutical research. Central to the integrated system is a Mitsubishi robot, which hands off samples throughout the process to the next station, including synthesis and purification, sample dispensing for purity and quantification analysis, dry-down, and aliquot generation.

Contribution to the study of new hydrogen production, purification and storage processes

International Nuclear Information System (INIS)

Manaud, Jean-Pierre

1984-01-01

This research thesis addresses the various aspects of hydrogen production, purification and process within the scope of hydrogen-based energy production. Hydrogen production is achieved by water decomposition through a thermo-chemical process. The author reports the thermodynamic assessment of a water decomposition thermo-chemical cycle for chlorine and sulphur-related cycles. He reports the experimental investigation of hydrogen purification by selective diffusion, the study of contamination of a CeMg12 alloy by nitrogen, oxygen and water vapour with application to hydrogen storage under the form of hydrides [fr

Purification of yeast alcohol dehydrogenase by using immobilized metal affinity cryogels

International Nuclear Information System (INIS)

Akduman, Begüm; Uygun, Murat; Uygun, Deniz Aktaş; Akgöl, Sinan; Denizli, Adil

2013-01-01

In this study, poly(2-hydroxyethyl methacrylate–glycidylmethacrylate) [poly(HEMA–GMA)] cryogels were prepared by radical cryocopolymerization of HEMA with GMA as a functional comonomer and N,N′-methylene-bisacrylamide (MBAAm) as a crosslinker. Iminodiacetic acid (IDA) functional groups were attached via ring opening of the epoxy group on the poly(HEMA–GMA) cryogels and then Zn(II) ions were chelated with these structures. Characterization of cryogels was performed by FTIR, SEM, EDX and swelling studies. These cryogels have interconnected pores of 30–50 μm size. The equilibrium swelling degree of Zn(II) chelated poly(HEMA–GMA)-IDA cryogels was approximately 600%. Zn(II) chelated poly(HEMA–GMA)-IDA cryogels were used in the adsorption of alcohol dehydrogenase from aqueous solutions and adsorption was performed in continuous system. The effects of pH, alcohol dehydrogenase concentration, temperature, and flow rate on adsorption were investigated. The maximum amount of alcohol dehydrogenase adsorption was determined to be 9.94 mg/g cryogel at 1.0 mg/mL alcohol dehydrogenase concentration and in acetate buffer at pH 5.0 with a flow rate of 0.5 mL/min. Desorption of adsorbed alcohol dehydrogenase was carried out by using 1.0 M NaCI at pH 8.0 phosphate buffer and desorption yield was found to be 93.5%. Additionally, these cryogels were used for purification of alcohol dehydrogenase from yeast with a single-step. The purity of desorbed alcohol dehydrogenase was shown by silver-stained SDS–PAGE. This purification process can successfully be used for the purification of alcohol dehydrogenase from unclarified yeast homogenates and this work is the first report about the usage of the cryogels for purification of alcohol dehydrogenase. - Highlights: • Poly(HEMA–GMA) cryogels were synthesized by radical cryocopolymerization technique. • Prepared cryogels were functionalized with IDA, then Zn(II) ions were chelated to the cryogel. • Zn(II) chelated poly

Purification of yeast alcohol dehydrogenase by using immobilized metal affinity cryogels

Energy Technology Data Exchange (ETDEWEB)

Akduman, Begüm [Chemistry Department, Adnan Menderes University, Aydın (Turkey); Uygun, Murat [Koçarlı Vocational and Training School, Adnan Menderes University, Aydın (Turkey); Uygun, Deniz Aktaş, E-mail: daktas@adu.edu.tr [Chemistry Department, Adnan Menderes University, Aydın (Turkey); Akgöl, Sinan [Biochemistry Department, Ege University, İzmir (Turkey); Denizli, Adil [Chemistry Department, Hacettepe University, Ankara (Turkey)

2013-12-01

In this study, poly(2-hydroxyethyl methacrylate–glycidylmethacrylate) [poly(HEMA–GMA)] cryogels were prepared by radical cryocopolymerization of HEMA with GMA as a functional comonomer and N,N′-methylene-bisacrylamide (MBAAm) as a crosslinker. Iminodiacetic acid (IDA) functional groups were attached via ring opening of the epoxy group on the poly(HEMA–GMA) cryogels and then Zn(II) ions were chelated with these structures. Characterization of cryogels was performed by FTIR, SEM, EDX and swelling studies. These cryogels have interconnected pores of 30–50 μm size. The equilibrium swelling degree of Zn(II) chelated poly(HEMA–GMA)-IDA cryogels was approximately 600%. Zn(II) chelated poly(HEMA–GMA)-IDA cryogels were used in the adsorption of alcohol dehydrogenase from aqueous solutions and adsorption was performed in continuous system. The effects of pH, alcohol dehydrogenase concentration, temperature, and flow rate on adsorption were investigated. The maximum amount of alcohol dehydrogenase adsorption was determined to be 9.94 mg/g cryogel at 1.0 mg/mL alcohol dehydrogenase concentration and in acetate buffer at pH 5.0 with a flow rate of 0.5 mL/min. Desorption of adsorbed alcohol dehydrogenase was carried out by using 1.0 M NaCI at pH 8.0 phosphate buffer and desorption yield was found to be 93.5%. Additionally, these cryogels were used for purification of alcohol dehydrogenase from yeast with a single-step. The purity of desorbed alcohol dehydrogenase was shown by silver-stained SDS–PAGE. This purification process can successfully be used for the purification of alcohol dehydrogenase from unclarified yeast homogenates and this work is the first report about the usage of the cryogels for purification of alcohol dehydrogenase. - Highlights: • Poly(HEMA–GMA) cryogels were synthesized by radical cryocopolymerization technique. • Prepared cryogels were functionalized with IDA, then Zn(II) ions were chelated to the cryogel. • Zn(II) chelated poly

Effective Purification of Biogas by Condensing-Liquid Membrane

Czech Academy of Sciences Publication Activity Database

Poloncarzová, Magda; Vejražka, Jiří; Veselý, Václav; Izák, Pavel

2010-01-01

Roč. 50, č. 3 (2010), s. 669-671 ISSN 1433-7851 R&D Projects: GA MPO FR-TI1/245 Institutional research plan: CEZ:AV0Z40720504 Keywords : biogas purification * condensing liquid * gas permeation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 12.730, year: 2010

Testing of the influenza virus purification by CIEF

Czech Academy of Sciences Publication Activity Database

Horká, Marie; Kubíček, O.; Kubesová, Anna; Kubíčková, Z.; Rosenbergová, K.; Šlais, Karel

2010-01-01

Roč. 31, č. 2 (2010), s. 331-338 ISSN 0173-0835 R&D Projects: GA AV ČR IAAX00310701 Institutional research plan: CEZ:AV0Z40310501 Keywords : capillary isoelectric focusing * PCR * purification efficiency Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.569, year: 2010

Purification and characterization of the chitosanase from Aeromonas ...

African Journals Online (AJOL)

Purification and characterization of the chitosanase from Aeromonas sp. HG08. Y Sun, J Zhang, S Wang. Abstract. In this work, the characterization of a chitosanase-producing bacterium isolated from soil was reported and this strain was grouped under the genus Aeromonas by virtue of its morphological, physiological ...

The Partial Purification and Characterization of Trypsin From the ...

African Journals Online (AJOL)

VESTEL

fractionation, dialysis and Sephadex G-75 gel filtration. The purification fold and yield were 6.23 and. 4.49%, respectively. .... It was subjected to water wash and digestive tracts were .... sulphate precipitation was a simple method and generally.

Analysis of the outlook for using narrow-band spontaneous emission sources for atmospheric air purification

International Nuclear Information System (INIS)

Boyarchuk, K A; Karelin, A V; Shirokov, R V

2003-01-01

The outlook for using narrow-band spontaneous emission sources for purification of smoke gases from sulphur and nitrogen oxides is demonstrated by calculations based on a nonstationary kinetic model of the N 2 - O 2 - H 2 O - CO 2 - SO 2 mixture. The dependences of the mixture purification efficiency on the UV source power at different wavelengths, the exposure time, and the mixture temperature are calculated. It is shown that the radiation sources proposed in the paper will provide better purification of waste gases in the atmosphere. The most promising is a KrCl* lamp emitting an average power of no less than 100 W at 222 nm. (laser applications and other topics in quantum electronics)

Development of an aptamer-based affinity purification method for vascular endothelial growth factor

Directory of Open Access Journals (Sweden)

Maren Lönne

2015-12-01

Full Text Available Since aptamers bind their targets with high affinity and specificity, they are promising alternative ligands in protein affinity purification. As aptamers are chemically synthesized oligonucleotides, they can be easily produced in large quantities regarding GMP conditions allowing their application in protein production for therapeutic purposes. Several advantages of aptamers compared to antibodies are described in general within this paper. Here, an aptamer directed against the human Vascular Endothelial Growth Factor (VEGF was used as affinity ligand for establishing a purification platform for VEGF in small scale. The aptamer was covalently immobilized on magnetic beads in a controlled orientation resulting in a functional active affinity matrix. Target binding was optimized by introduction of spacer molecules and variation of aptamer density. Further, salt-induced target elution was demonstrated as well as VEGF purification from a complex protein mixture proving the specificity of protein-aptamer binding.

The application of modified montmorillonite in the processes of baromembrane purification of water from U (VI)

International Nuclear Information System (INIS)

Yurlova, L.Yu.; Krivoruchko, A.P.

2010-01-01

The processes of uranium-containing water purification by ultra- and nanofiltration methods combined with the use of montmorillonite modified by polyethyleneimine are studied. It is shown that the application of montmorillonite allows one to obtain the high indices of the uranium-containing water purification by baromembrane methods.

Drinking water purification in the Czech Republic and worldwide

International Nuclear Information System (INIS)

Krmela, Jan; Beckova, Vera; Vlcek, Jaroslav; Marhol, Milan

2012-06-01

The report is structured as follows: (i) Legislative (hygienic) requirements for technologies applied to drinking water purification with focus on uranium elimination; (ii) Technological drinking water treatment processes (settling, filtration, precipitation, acidification, iron and manganese removal) ; (iii) State Office for Nuclear Safety requirements for the operation of facilities to separate uranium from drinking water and for the handling of saturated ionexes from such facilities; (iv) Material requirements for the operation of ionex filters serving to separate uranium from drinking water; (v) Effect of enhanced uranium concentrations in drinking waters on human body; (vi) Uranium speciation in ground waters; (vii) Brief description of technologies which are used worldwide for uranium removal; (viii) Technologies which are usable and are used in the Czech Republic for drinking water purification from uranium; (ix) Inorganic and organic ion exchangers and sorbents. (P.A.)

Exergy costs analysis of water desalination and purification techniques by transfer functions

International Nuclear Information System (INIS)

Carrasquer, Beatriz; Martínez-Gracia, Amaya; Uche, Javier

2016-01-01

Highlights: • A procedure to estimate the unit exergy cost of water treatment techniques is provided. • Unit exergy costs of water purification and desalination are given as a function of design and operating parameters. • Unit exergy costs range from 3.3 to 6.8 in purification and from 2 to 26 in desalination. • They could be used in their preliminary design as good indicators of their energy efficiency. - Abstract: The unit exergy costs of desalination and purification, which are two alternatives commonly used for water supply and treatment, have been characterized as a function of the energy efficiency of the process by combining the Exergy Cost Analysis with Transfer Function Analysis. An equation to assess the exergy costs of these alternatives is then proposed as a quick guide to know the energy efficiency of any water treatment process under different design and operating conditions. This combination, was satisfactory applied to groundwaters and water transfers. After identifying the boundaries of the system, input and output flows are calculated in exergy values. Next, different examples are analyzed in order to propose a generic equation to assess the exergy cost of the water restoration technologies, attending to their main features. Recovery ratio, energy requirements and salts concentrations (for desalination), and plant capacity and organic matter recovery (for water purification) are introduced in the calculations as their main endogenous parameters. Values obtained for typical operation ranges of commercial plants showed that unit exergy costs of water purification ranged from 3.3 to 6.8; maximum values, as expected, were found at low plant capacities and high organic matter removal ratios. For water desalination, values varied from 2 to 7 in membrane technologies and from 10 to 26 in thermal processes. The recovery ratio and salts concentration in raw water increased the unit exergy costs in membrane techniques. In distillation processes

An Investigation on the Efficiency of Air Purification Using a Biofilter with Activated Bed of Different Origin

Directory of Open Access Journals (Sweden)

Zagorskis Alvydas

2014-12-01

Full Text Available Recent studies in the area of biological air treatment in filters have addressed fundamental key issues, such as a biofilter bed of different origin composed of natural zeolite granules, foam cubes and wood chips. When foam and zeolite are mixed with wood chips to remove volatile organic compounds from the air, not only biological but also adsorption air purification methods are accomplished. The use of complex purification technologies helps to improve the efficiency of a filter as well as the bed service life of the filter bed. Investigations revealed that microorganisms prevailing in biological purification, can also reproduce themselves in biofilter beds of inorganic and synthetic origin composed of natural zeolite and foam. By cultivating associations of spontaneous microorganisms in the filter bed the dependencies of the purification efficiency of filter on the origin, concentration and filtration time of injected pollutants were determined. The highest purification efficiency was obtained when air polluted with acetone vapour was supplied to the equipment at 0.1 m/s of superficial gas velocity. When cleaning air from volatile organic compounds (acetone, toluene and butanol, under the initial pollutant concentration of ~100 mg/m3, the filter efficiency reached 95 %.

Chromatographic and electrophoretic methods for nanodisc purification and analysis

DEFF Research Database (Denmark)

Justesen, Bo Højen; Günther-Pomorski, Thomas

2014-01-01

Soluble nanoscale lipid bilayers, termed nanodiscs, are widely used in science for studying the membrane-anchored and integral membrane protein complexes under defined experimental conditions. Although their formation occurs by a self-assembly process, nanodisc purification and the verification...

Research progress of novel adsorption processes in water purification:A review

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

As an effective, efficient, and economic approach for water purification, adsorbents and adsorption processes have been widely studied and applied in different aspects for a long time. In the recent years, a lot of novel adsorption processes have been developed for enhancing the efficiency of removing the organic and inorganic contaminants from water. This article reviews some new adsorbents and advanced adsorption methods that specialize in their compositions, structures, functions, and characteristics used in water treatment. The review emphasizes adsorption/catalytic oxidation process, adsorption/catalytic reduction process, adsorption coupled with redox process, biomimetic sorbent and its sorption behaviors of POPs, and modified adsorbents and their water purification efficiency.

Use of sulfur hexafluoride airflow studies to determine the appropriate number and placement of air monitors in an alpha inhalation exposure laboratory

Energy Technology Data Exchange (ETDEWEB)

Newton, G.J.; Hoover, M.D.

1995-12-01

Determination of the appropriate number and placement of air monitors in the workplace is quite subjective and is generally one of the more difficult tasks in radiation protection. General guidance for determining the number and placement of air sampling and monitoring instruments has been provided by technical reports such as Mishima, J. These two documents and other published guidelines suggest that some insight into sampler placement can be obtained by conducting airflow studies involving the dilution and clearance of the relatively inert tracer gas sulfur hexafluoride (SF{sub 6}) in sampler placement studies and describes the results of a study done within the ITRI alpha inhalation exposure laboratories. The objectives of the study were to document an appropriate method for conducting SF{sub 6} dispersion studies, and to confirm the appropriate number and placement of air monitors and air samplers within a typical ITRI inhalation exposure laboratory. The results of this study have become part of the technical bases for air sampling and monitoring in the test room.

[Managment of subretinal heamorrhages within the macular area using intravitreal injections of recombined tissue plasminogen activator, sulphur hexafluoride and ranihizumab--preliminary report].

Science.gov (United States)

Miniewicz, Joanna; Kubicka-Trząska, Agnieszka; Karska-Basta, Izabella; Romanowska-Dixon, Boźena

2015-01-01

Submacular hemorrhages cause serious vision impairment. Patient observation, waiting for the spontaneous blood reabsorption and resolution of the haemorrhage leads to the severe damage to retinal tissue as a result of scar formation. The paper presents 7 cases of patients with submacular haemorrhages treated with intravitreal injections of recombined tissue plasminogen activator (rtPA) and sulphur hexafluoride (SFG). In 4 cases, the haemorrhage was secondary to AMD, in two cases to trauma, and it was idiopathic in one case. All patients were treated with intravitreal injections of rtPA and SF6 for thrombolysis and pneumatic displacement of haemorrhage outside macular structures. Ranibizumab was additionally administered to patients with age-related macular degeneration. Such treatment improved visual acuity in all patients, reducing the central retinal thickness as shown in follow-up optical coherence tomography. The presented treatment of submacular hemorrhages with intravitreal injections of rtPA and SF6 provided good results, but in order to develop a standard management algorithm for this disease, the analysis of larger patient sample is required.

Purification of bovine thyroid-stimulating hormone by a monoclonal antibody

International Nuclear Information System (INIS)

Lock, A.J.; van Denderen, J.; Aarden, L.A.

1988-01-01

A monoclonal antibody directed against bovine TSH was obtained by hybridoma technology. This antibody was specific for TSH and did not react with bovine LH and FSH. Affinity chromatography of crude TSH was performed on anti-TSH Sepharose. Bovine TSH was purified in a single step to near homogeneity by this technique, as shown by cation exchange chromatography and sodium dodecyl sulfate-polyacrylamide gel electrophoresis of the purified TSH. The biological activity of the hormone was not affected during the purification, as determined by [ 3 H]thymidine incorporation of the TSH-dependent FRTL5 cell line. The results indicate that affinity purification of TSH by means of a monoclonal antibody is a simple one-step procedure for the production of biologically active, highly purified TSH

Purification of gaseous and liquid releases by electron irradiation. Application of the radiation method to the purification and bacterial decontamination of liquids

International Nuclear Information System (INIS)

Otcenasek, P.

1997-01-01

Electron beams produced by electron accelerators, and gamma rays emitted by suitable radioisotopes such as Co-60 can be used to purify gases and liquids. Research and development efforts are concentrating on the following fields: (i) radiation treatment of natural and polluted drinking water, (ii) radiation purification of industrial liquid wastes, (iii) radiation purification of waste sludges, and (iv) radiation purification of flue gases. Radiation doses not exceeding 1 kGy are sufficient for the decolorization, deodorization, and disinfection of drinking water, whereas doses in the order of tens of kGy are necessary for the treatment of wastewaters. Therefore, wastewaters are first purified by conventional methods, followed by an aftertreatment with fast electrons. Active species such as OH and H radicals emerge, causing oxidation and/or decomposition of organic pollutants and exerting disinfecting effects. Gas treatment with electron beams is suitable for removing some inorganic elements and compounds and other pollutants. Applicability of this approach has been confirmed for chlorinated aromatic hydrocarbons, phenols, benzene derivatives, dioxin, and furan derivatives. For instance, the attained degree of dioxin removal from water was 99%. Trichloroethylene can be decomposed by application of a dose of 7 kGy, giving rise to carbon dioxide, hydrogen chloride, and chlorine. The resulting aerosol particles can be collected, concentrated, and disposed of by combustion or biological degradation. The method shows promise for the removal of hydrocarbons from large volumes of gases with initial concentrations of 50 to 100 mg carbon per cubic metre. (P.A.). 1 fig., 1 ref

POSSIBILITY FOR APPLICATION OF LIQUEFIED GASES FOR PURIFICATION OF BARBERRY ALKALOIDS

Directory of Open Access Journals (Sweden)

Demyanenko D.V.

2016-06-01

Full Text Available Introduction. Biologically active substances (BAS of barberry roots represented by alkaloids of isoquinoline group are perspective substances for development of preparations with multiple pharmacological activities. However, now manufacture of them in Ukraine is stopped. One of the reasons of this is out-of-date production technologies of alkaloids involving use of toxic and/or flammable solvents. In the article possibility for application of liquefied gases in technology of obtaining of alkaloids from barberry roots has been studied. Materials and methods. Initial raw herb drug were barberry (Berberis vulgaris roots harvested in spring on the territory of Southern Ukraine. Their moisture content was 11%, comminuting degree was 0,5-1,4 mm. At the first stage purification of raw herb drug from lipophilic impurities (defatting was made with use of some liquefied gases: tetrafluoroethane, isobutane, difluorochloromethane and difluoromethane. Extraction of the alkaloid sum was made with difluoromethane mixed with various quantities of liquid ammonia or diethylamine as alkaline agent. Crude extracts were exposed to two-level liquefied-gas purification. At first the alkaloid bases were transformed into saline forms with aqueous solutions of acids and purified from ballast impurities with liquefied freon-22. Then alkaloid salts were reextracted from aqueous phase in the base form with liquefied mixture of difluoromethane and ammonia. Mixing of liquid phases was provided by creation of alternate gradients of temperatures and, as consequence, pressures between separators feeding alternately cool water into jacket of one of them, and warm water – into jacket of another one. Quantity of lipophilic ballast impurities and also weight of extractives were determined gravimetrically. Quantitative analysis of the alkaloid sum was made by titrimetric method after sedimentation of alkaloids with volumetric solution of phosphomolybdic acid. Results and discussion

Potential for sustainable energy with biogas from sewage purification

International Nuclear Information System (INIS)

Coenen, J.; Van Gastel, M.; De Jong, K.

2005-04-01

Insight is given into the possibility to produce biogas from sewage purification plants in the Netherlands. Attention is paid to the estimated potential of sustainable energy from biogas, the economic effectiveness of several scenarios, the critical success factors and bottlenecks [nl

Purification performances of common reed beds based on the ...

African Journals Online (AJOL)

SARAH

2013-11-30

Nov 30, 2013 ... advantages, the reed bed is a solution to Beninese purification problems. Since technical service agent of ... Journal of Applied Biosciences 71:5682– 5691. ISSN 1997–5902 ..... 15N/14N ratios. Journal of Hydrology, vol. 199,.

Novel heat-pump-assisted extractive distillation for bioethanol purification

NARCIS (Netherlands)

Luo, Hao; Bildea, Costin Sorin; Kiss, Anton A.

2015-01-01

The purification of bioethanol fuel involves an energy-intensive separation process to concentrate the diluted streams obtained in the fermentation stage and to overcome the azeotropic behavior of the ethanol-water mixture. The conventional separation sequence employs three distillation columns that

Air Versus Sulfur Hexafluoride Gas Tamponade in Descemet Membrane Endothelial Keratoplasty: A Fellow Eye Comparison.

Science.gov (United States)

von Marchtaler, Philipp V; Weller, Julia M; Kruse, Friedrich E; Tourtas, Theofilos

2018-01-01

To perform a fellow eye comparison of outcomes and complications when using air or sulfur hexafluoride (SF6) gas as a tamponade in Descemet membrane endothelial keratoplasty (DMEK). One hundred thirty-six eyes of 68 consecutive patients who underwent uneventful DMEK in both eyes for Fuchs endothelial corneal dystrophy were included in this retrospective study. Inclusion criteria were air tamponade (80% of the anterior chamber volume) in the first eye and 20% SF6 gas tamponade (80% of the anterior chamber volume) in the second eye; and same donor tissue culture condition in both eyes. All eyes received laser iridotomy on the day before DMEK. Main outcome measures included preoperative and postoperative best-corrected visual acuity, endothelial cell density, corneal volume, rebubbling rate, and rate of postoperative pupillary block caused by the air/gas bubble. Thirteen of 68 eyes (19.1%) with an air tamponade needed rebubbling compared with 4 of 68 eyes (5.9%) with an SF6 gas tamponade (P = 0.036). Postoperative pupillary block necessitating partial release of air/gas occurred in 1 eye (1.5%) with an air tamponade and 3 eyes (4.4%) with an SF6 gas tamponade (P = 0.301). There were no significant differences in preoperative and postoperative best-corrected visual acuity, endothelial cell density, and corneal volume within 3-month follow-up. Our results confirm the previously reported better graft adhesion when using an SF6 gas tamponade in DMEK without increased endothelial cell toxicity. The rate of pupillary block in eyes with an SF6 gas tamponade was comparable to that with an air tamponade. As a consequence, we recommend using SF6 gas as the tamponade in DMEK.

Partial Purification of Antimicrobial Compounds Isolated from Mycelia of Tropical Lentinus cladopus LC4

OpenAIRE

SUDIRMAN, LISDAR IDWAN

2010-01-01

Lentinus cladopus LC4 produced at least eight antimicrobial compounds (ACs) which are active against plant and human pathogens. Three ACs in its crude mycelial were extracted with methanol and partial purification was carried out with silicic acid column chromatography and by thin layer chromatography (PTLC). The antimicrobial activity was tested by paper disc method and antibiographic method. The chromatography purification eluted with dichloromethane containing 5% methanol gave one active f...

Development of novel membranes for blood purification therapies based on copolymers of N-vinylpyrrolidone and n-butylmethacrylate

NARCIS (Netherlands)

Tijink, M.S.L.; Janssen, J.; Timmer, M.; Austen, J.; Aldenhoff, Y.; Kooman, J.; Koole, L.H.; Damoiseaux, J.; van Oerle, R.; Henskens, Y.; Stamatialis, Dimitrios

2013-01-01

Developments in membrane based blood purification therapies often come with longer treatment times and therefore longer blood–material contact, which requires long-term membrane biocompatibility. In this study, we develop for the first time membranes for blood purification using the material

Moderate temperature gas purification system: Application to high calorific coal-derived fuel

Energy Technology Data Exchange (ETDEWEB)

Kobayashi, M.; Shirai, H.; Nunokawa, M. [Central Research Institute of Electric Power Industry, Kanagawa (Japan)

2008-01-15

Simultaneous removal of dust, alkaline and alkaline-earth metals, halides and sulfur compounds is required to enlarge application of coal-derived gas to the high-temperature fuel cells and the fuel synthesis through chemical processing. Because high calorific fuel gas, such as oxygen-blown coal gas, has high carbon monoxide content, high-temperature (above 450{sup o}C) gas purification system is always subjected to the carbon deposition. We suggest moderate temperature (around 300{sup o}C) operation of the gas purification system to avoid the harmful disproportionation reaction and efficient removal of the various contaminants. Because the reaction rate is predominant to the performance of contaminant removal in the moderate temperature gas purification system, we evaluated the chemical removal processes; performance of the removal processes for halides and sulfur compounds was experimentally evaluated. The halide removal process with sodium aluminate sorbent had potential performance at around 300{sup o}C. The sulfur removal process with zinc ferrite sorbent was also applicable to the temperature range, though the reaction kinetics of the sorbent is essential to be approved.

Molecular Cloning Expression And Purification Studies With An ORF Of Mycobacterium Tuberculosis

Directory of Open Access Journals (Sweden)

Chiranjibi Chaudhary

2017-08-01

Full Text Available The study was initiated to develop a recombinant strain for expression and production of large scale protein and to develop its purification protocol. The MRAORF-X was amplified from the genomic DNA of M. tuberculosis H37Ra. The amplicon was successfully cloned in a cloning vector pGEM-T Easy and transformed in cloning host DH5amp945. Recombinant clones were identified by blue-white screening and insert presence was confirmed by restriction digestion of plasmid isolated from white colonies. Expression vector pET32a was used for protein expression. The recombinant plasmid was transformed into expression host BL21 and protein expression was checked by SDS-PAGE. The desired protein was approximately 60 kDa in size including tags. The purification protocol was established for purification from inclusion bodies. The purity of purified protein was assessed by SDS-PAGE gel run and presence of a single band at 60 kDa suggested that the inclusion bodies were a good source of purified protein.

High-yield recombinant expression and purification of marginally soluble, short elastin-like polypeptides.

Science.gov (United States)

Bahniuk, Markian S; Alshememry, Abdullah K; Unsworth, Larry D

2016-12-01

The protocol described here is designed as an extension of existing techniques for creating elastin-like polypeptides. It allows for the expression and purification of elastin-like polypeptide (ELP) constructs that are poorly expressed or have very low transition temperatures. DNA concatemerization has been modified to reduce issues caused by methylation sensitivity and inefficient cloning. Linearization of the modified expression vector has been altered to greatly increase cleavage efficiency. The purification regimen is based upon using denaturing metal affinity chromatography to fully solubilize and, if necessary, pre-concentrate the target peptide before purification by inverse temperature cycling (ITC). This protocol has been used to express multiple leucine-containing elastin-like polypeptides, with final yields of 250-660 mg per liter of cells, depending on the specific construct. This was considerably greater than previously reported yields for similar ELPs. Due to the relative hydrophobicity of the tested constructs, even compared with commonly employed ELPs, conventional methods would not have been able to be purify these peptides.

Development of a production scale purification of Ge-68 from irradiated gallium metal

Energy Technology Data Exchange (ETDEWEB)

Fitzsimmons, Jonathan M.; Mausner, Leonard [Brookhaven National Laboratory, Upton, NY (United States)

2015-05-01

Germanium-68 (Ge-68) is produced by proton irradiation of a gallium metal target and purified by organic extraction. The Ge-68 can be used in a medical isotope generator to produce Gallium-68 (Ga-68) which can be used to radiolabel PET imaging agents. The emerging use of Ge-68 in the Ga-68 medical isotope generator has caused us to develop a new purification method for Ge-68 that does not use toxic solvents. The purpose of this work was to develop a production scale separation of Ge-68 that utilizes a leaching step to remove a bulk of the gallium metal, followed by purification with Sephadex {sup copyright} G25. Production scale (300 mCi) purification was performed with the new method. The purified Ge-68 contained the highest radioactivity concentration of Ge-68 produced at BNL; the sample meet Department of Energy specifications and the method had an excellent recovery of Ge-68.

Purification and characterization of broccoli (Brassica oleracea var. italica) myrosinase (β-thioglucosidase glucohydrolase).

Science.gov (United States)

Mahn, Andrea; Angulo, Alejandro; Cabañas, Fernanda

2014-12-03

Myrosinase (β-thioglucosidase glucohydrolase, EC 3.2.1.147) from broccoli (Brassica oleracea var. italica) was purified by ammonium sulfate precipitation followed by concanavalin A affinity chromatography, with an intermediate dialysis step, resulting in 88% recovery and 1318-fold purification. These are the highest values reported for the purification of any myrosinase. The subunits of broccoli myrosinase have a molecular mass of 50-55 kDa. The native molecular mass of myrosinase was 157 kDa, and accordingly, it is composed of three subunits. The maximum activity was observed at 40 °C and at pH below 5.0. Kinetic assays demonstrated that broccoli myrosinase is subjected to substrate (sinigrin) inhibition. The Michaelis-Menten model, considering substrate inhibition, gave Vmax equal to 0.246 μmol min(-1), Km equal to 0.086 mM, and K(I) equal to 0.368 mM. This is the first study about purification and characterization of broccoli myrosinase.

Magnetic particles as powerful purification tool for high sensitive mass spectrometric screening procedures.

Science.gov (United States)

Peter, Jochen F; Otto, Angela M

2010-02-01

The effective isolation and purification of proteins from biological fluids is the most crucial step for a successful protein analysis when only minute amounts are available. While conventional purification methods such as dialysis, ultrafiltration or protein precipitation often lead to a marked loss of protein, SPE with small-sized particles is a powerful alternative. The implementation of particles with superparamagnetic cores facilitates the handling of those particles and allows the application of particles in the nanometer to low micrometer range. Due to the small diameters, magnetic particles are advantageous for increasing sensitivity when using subsequent MS analysis or gel electrophoresis. In the last years, different types of magnetic particles were developed for specific protein purification purposes followed by analysis or screening procedures using MS or SDS gel electrophoresis. In this review, the use of magnetic particles for different applications, such as, the extraction and analysis of DNA/RNA, peptides and proteins, is described.

Preparation and Characterization of Zeolite Membrane for Bioethanol Purification

Directory of Open Access Journals (Sweden)

Aprilina Purbasari

2013-06-01

Full Text Available The use of bioethanol as an alternative fuel with a purity of more than 99.5% wt has prompted research on bioethanol purification. One of the promising methods used for bioethanol purification is pervaporation membrane. This research is aimed to prepare and characterize zeolite membranes for pervaporation membrane. The membrane preparation consisted of two stages, namely support preparation and zeolite deposition on the support. In support preparation, α- alumina and kaolin with specific composition (50:30; 40:40; 50:30 was mixed with additives and water. After pugging and aging process, the mixture became paste and extruded into tubular shape. The tube was then calcined at temperature of 1250 °C for 3 hours. After that, zeolite 4A was deposited on the tubes using clear solution made of 10 %wt zeolite and 90 %wt water and heated at temperature of 80 °C for 3 hours. Furthermore, the resulting zeolite membranes was washed with deionized water for 5 minutes and dried in oven at temperature of 100 °C for 24 hours. Characterization of zeolite membranes included mechanical strength test, XRD, and SEM. In the mechanical strength test, the membrane sample with α- alumina:kaolin = 50:30 (membrane A has the highest mechanical strength of 46.65 N/mm2. Result of XRD analysis for the membrane A indicated that mullite and corundum phases were formed, which mullite phase was more dominant. Meanwhile the result of SEM analysis shows that zeolite crystals have been formed and covered the pores support, but the deposition of zeolite has not been optimal yet. The performance examination for bioethanol purification showed that the membrane could increase the purity of bioethanol from 95% to 98.5% wt. © 2013 BCREC UNDIP. All rights reservedReceived: 23rd October 2012; Revised: 15th February 2013; Accepted: 16th February 2013[How to Cite: Purbasari, A., Istirokhatun, T., Devi, A.M., Mahsunnah, L. , Susanto, H. (2013. Preparation and Characterization of Zeolite

Recombinant expression and purification of a tumor-targeted toxin in Bacillus anthracis

International Nuclear Information System (INIS)

Bachran, Christopher; Abdelazim, Suzanne; Fattah, Rasem J.; Liu, Shihui; Leppla, Stephen H.

2013-01-01

Highlights: ► Non-infectious and protease-deficient Bacillus anthracis protein expression system. ► Successful expression and purification of a tumor-targeted fusion protein drug. ► Very low endotoxin contamination of purified protein. ► Efficient protein secretion simplifies purification. ► Functional anti-tumor fusion protein purified. -- Abstract: Many recombinant therapeutic proteins are purified from Escherichia coli. While expression in E. coli is easily achieved, some disadvantages such as protein aggregation, formation of inclusion bodies, and contamination of purified proteins with the lipopolysaccharides arise. Lipopolysaccharides have to be removed to prevent inflammatory responses in patients. Use of the Gram-positive Bacillus anthracis as an expression host offers a solution to circumvent these problems. Using the multiple protease-deficient strain BH460, we expressed a fusion of the N-terminal 254 amino acids of anthrax lethal factor (LFn), the N-terminal 389 amino acids of diphtheria toxin (DT389) and human transforming growth factor alpha (TGFα). The resulting fusion protein was constitutively expressed and successfully secreted by B. anthracis into the culture supernatant. Purification was achieved by anion exchange chromatography and proteolytic cleavage removed LFn from the desired fusion protein (DT389 fused to TGFα). The fusion protein showed the intended specific cytotoxicity to epidermal growth factor receptor-expressing human head and neck cancer cells. Final analyses showed low levels of lipopolysaccharides, originating most likely from contamination during the purification process. Thus, the fusion to LFn for protein secretion and expression in B. anthracis BH460 provides an elegant tool to obtain high levels of lipopolysaccharide-free recombinant protein.

Purification and some kinetic properties of catalase from parsley (Petroselinum hortense Hoffm., Apiaceae) leaves.

Science.gov (United States)

Oztürk, Lokman; Bülbül, Metin; Elmastas, Mahfuz; Ciftçi, Mehmet

2007-01-01

In this study, catalase (CAT: EC 1.11.1.6) was purified from parsley (Petroselinum hortense) leaves; analysis of the kinetic behavior and some properties of the enzyme were investigated. The purification consisted of three steps, including preparation of homogenate, ammonium sulfate fractionation, and fractionation by DEAE-Sephadex A50 ion exchange chromatography. The enzyme was obtained with a yield of 9.5% and had a specific activity of 1126 U (mg proteins)(-1). The overall purification was about 5.83-fold. A temperature of 4 degrees C was maintained during the purification process. Enzyme activity was spectrophotometrically measured at 240 nm. In order to control the purification of the enzyme, SDS-polyacrylamide gel electrophoresis was carried out in 4% and 10% acryl amide for stacking and running gel, respectively. SDS-polyacrylamide gel electrophoresis showed a single band for the enzyme. The molecular weight was found to be 183.29 kDa by Sephadex G-200 gel filtration chromatography. The stable pH, optimum pH, and ionic strength were determined for phosphate and Tris-HCl buffer systems. In addition, K(M) and V(max) values for H(2)O(2), at optimum pH and 25 degrees C, were determined by means of Lineweaver-Burk plots.

Expression microarray reproducibility is improved by optimising purification steps in RNA amplification and labelling

Directory of Open Access Journals (Sweden)

Brenton James D

2004-01-01

Full Text Available Abstract Background Expression microarrays have evolved into a powerful tool with great potential for clinical application and therefore reliability of data is essential. RNA amplification is used when the amount of starting material is scarce, as is frequently the case with clinical samples. Purification steps are critical in RNA amplification and labelling protocols, and there is a lack of sufficient data to validate and optimise the process. Results Here the purification steps involved in the protocol for indirect labelling of amplified RNA are evaluated and the experimentally determined best method for each step with respect to yield, purity, size distribution of the transcripts, and dye coupling is used to generate targets tested in replicate hybridisations. DNase treatment of diluted total RNA samples followed by phenol extraction is the optimal way to remove genomic DNA contamination. Purification of double-stranded cDNA is best achieved by phenol extraction followed by isopropanol precipitation at room temperature. Extraction with guanidinium-phenol and Lithium Chloride precipitation are the optimal methods for purification of amplified RNA and labelled aRNA respectively. Conclusion This protocol provides targets that generate highly reproducible microarray data with good representation of transcripts across the size spectrum and a coefficient of repeatability significantly better than that reported previously.

The technology of large-scale pharmaceutical plasmid purification ...

African Journals Online (AJOL)

Further test demonstrated that the pcDNAlacZ purified with CTAB and authoritative endotoxin-free plasmid Kit had the similar transfection efficiency in vivo and in vitro. CTAB can be used for plasmid purification; the main advantages of the DNAs purified with CTAB include the avoidance of animal-derived enzymes, toxic ...

Advanced purification strategy for CueR, a cysteine containing copper(I) and DNA binding protein

DEFF Research Database (Denmark)

Balogh, Ria K.; Gyurcsik, Béla; Hunyadi-Gulyás, Éva

2016-01-01

. A detailed understanding of their function may be exploited in potential health, environmental and analytical applications. Members of the MerR protein family sense a broad range of mostly late transition and heavy metal ions through their cysteine thiolates. The air sensitivity of latter groups makes...... the expression and purification of such proteins challenging. Here we describe a method for the purification of the copper-regulatory CueR protein under optimized conditions. In order to avoid protein precipitation and/or eventual aggregation and to get rid of the co-purifying Escherichia coli elongation factor...... any affinity tag. Structure and functionality tests performed with mass spectrometry, circular dichroism spectroscopy and electrophoretic gel mobility shift assays approved the success of the purification procedure....

Enriched Water-H{sub 2} {sup 18}O Purification to be Used in Routine {sup 18}FDG Production

Energy Technology Data Exchange (ETDEWEB)

Al Rayyes, A. H. [Atomic Energy Commission of Syria, Chemistry Department, Cyclotron Division, Damascus (Syrian Arab Republic)

2009-07-01

Oxygen-18 enriched water has been recovered from IBA (Ion Beam Applications) recovery system followed by purification and then used in the production of {sup 18}F-. The purification process has been carried out by irradiation with UV followed by a distillation under vacuum. After purification, 95% of water is recovered and organic compounds, radioisotopes, trace metals and gases are eliminated efficiently. Results show that there are no significant differences in (2-deoxy-2-[{sup 18}F]fluoro-D-glucose ([{sup 18}F]FDG) production yield using purified water by the proposed method and new enriched water. Tritium was detected in the irradiated enriched water. Contamination precautions during purification should be considered. Tritium was not present in {sup 18}FDG or Na-{sup 18}F final products. (author)

Effect of Different Purification Techniques on the Characteristics of Heteropolysaccharide-Protein Biopolymer from Durian (Durio zibethinus Seed

Directory of Open Access Journals (Sweden)

Hamed Mirhosseini

2012-09-01

Full Text Available Natural biopolymers from plant sources contain many impurities (e.g., fat, protein, fiber, natural pigment and endogenous enzymes, therefore, an efficient purification process is recommended to minimize these impurities and consequently improve the functional properties of the biopolymer. The main objective of the present study was to investigate the effect of different purification techniques on the yield, protein content, solubility, water- and oil-holding capacity of a heteropolysaccharide-protein biopolymer obtained from durian seed. Four different purification methods using different chemicals and solvents (i.e., A (isopropanol and ethanol, B (isopropanol and acetone, C (saturated barium hydroxide, and D (Fehling solution] to liberate the purified biopolymer from its crude form were compared. In most cases, the purification process significantly (p < 0.05 improved the physicochemical properties of heteropolysaccharide-protein biopolymer from durian fruit seed. The present work showed that the precipitation using isopropanol and acetone (Method B resulted in the highest purification yield among all the tested purification techniques. The precipitation using saturated barium hydroxide (Method C led to induce the highest solubility and relatively high capacity of water absorption. The current study reveals that the precipitation using Fehling solution (Method D most efficiently eliminates the protein fraction, thus providing more pure biopolymer suitable for biological applications.

Stress analysis of the O-element pipe during the process of flue gases purification

Directory of Open Access Journals (Sweden)

Nekvasil R.

2008-11-01

Full Text Available Equipment for flue gases purification from undesired substances is used throughout power and other types of industry. This paper deals with damaging of the O-element pipe designed to remove sulphur from the flue gases, i.e. damaging of the pipe during flue gases purification. This purification is conducted by spraying the water into the O-shaped pipe where the flue gases flow. Thus the sulphur binds itself onto the water and gets removed from the flue gas. Injection of cold water into hot flue gases, however, causes high stress on the inside of the pipe, which can gradually damage the O-element pipe. In this paper initial injection of water into hot pipe all the way to stabilization of temperature fields will be analyzed and the most dangerous places which shall be considered for fatigue will be determined.

Proposal of the system for the biogas purification using vitreous and natural zeolite membranes

International Nuclear Information System (INIS)

Ortega Viera, Lianys; Fernández SantanI, Elina; Alfonso Martínez, Félix Enrique; Aguiar RoqueI, Yania; Rodríguez Muñoz, Susana

2017-01-01

One way to reduce the effects of climate change is to replace fossil fuels with renewable energy such as biogas, but the amount of hydrogen sulphide in it represents an impediment to its use, because of its negative impacts on human health, materials of construction and the environment, being essential its reduction or elimination. For this reason, it was defined as aim to propose an effective method for the purification of biogas using membranes constructed from vitreous waste materials and natural cuban zeolite. This treatment requires four membranes with their supports and eight valves and could be used by small farmers for the purification of 1.4 m 3 of biogas per day, an amount necessary for the cooking of three meals of a family of five people, being the cost of the biogas purification process equal to 0.06%/m 3 . (author)

Optimized conditions for high-level solubilization and purification of ...

African Journals Online (AJOL)

NH Computers

2011-10-10

Oct 10, 2011 ... filtration chromatography using Sephadex G-50 column. The purified protein was refolded by .... blocking with BSA, the nitrocellulose membrane was processed using rabbit monoclonal antibody raised ..... recombinant human growth hormone using radial flow chromatography. Protein Exp. Purif., 68: 54-59.