WorldWideScience

Sample records for hev traction applications

  1. A Study on Magnetic Decoupling of Compound-Structure Permanent-Magnet Motor for HEVs Application

    Directory of Open Access Journals (Sweden)

    Qiwei Xu

    2016-10-01

    Full Text Available The compound-structure permanent-magnet (CSPM motor is used for an electrical continuously-variable transmission (E-CVT in a hybrid electric vehicle (HEV. It can make the internal combustion engine (ICE independent of the road loads and run in the high efficiency area to improve the fuel economy and reduce the emissions. This paper studies the magnetic coupling of a new type of CSPM motor used in HEVs. Firstly, through the analysis of the parameter matching with CSPM in the HEV, we receive the same dynamic properties’ design parameters between the CSPM motor and the THS (Toyota Hybrid System of the Toyota Prius. Next, we establish the equivalent magnetic circuit model of the overall and the secondary model considering the tangential and radial flux distribution in the outer rotor of the CSPM motor. Based on these two models, we explore the internal magnetic coupling rule of the CSPM motor. Finally, finite element method analysis in 2D-ansoft is used to analyze the magnetic field distribution of the CSPM motor in different operation modes. By the result of the finite element method analysis, the internal magnetic decoupling scheme is put forward, laying the theoretical foundation for the further application of the CSPM motor in HEVs.

  2. Assessment by Simu ation of Benefits of New HEV Powertrain Configurations Évaluation par simulation des bénéfices de nouvelles chaînes de traction hybrides

    Directory of Open Access Journals (Sweden)

    Kim N.

    2013-05-01

    Full Text Available During the past couple of years, numerous powertrain configurations for Hybrid Electric Vehicles (HEV have been introduced into the marketplace. The current dominant architecture is the power-split configuration with the input split (single-mode from Toyota and Ford. General Motors (GM recently introduced a two-mode power-split configuration for applications in sport utility vehicles. Also, the first commercially available Plug-In Hybrid Electric Vehicle (PHEV — the GM Volt — was introduced into the market in 2010. The GM Volt uses a series-split powertrain architecture, which provides benefits over the series architecture, which typically has been considered for Electric-Range Extended Vehicles (E-REV. This paper assesses the benefits of these different powertrain architectures (single-mode versus multi-mode for HEV (series versus GM Voltec for PHEV by comparing component sizes, system efficiency and fuel consumption over several drive cycles. On the basis of dynamic models, a detailed component control algorithm was developed for each configuration. The powertrain components were sized to meet all-electric-range, performance and grade-capacity requirements. This paper presents and compares the impact of these different powertrain configurations on component size and fuel consumption. Durant les dernières années, de nombreuses configurations de motorisation pour véhicules hybrides ont été introduites sur le marché. La solution dominante est actuellement la dérivation de puissance en configuration ‘input split’ simple mode utilisée par Toyota et Ford. General Motors (GM a récemment introduit une configuration basée sur la dérivation de puissance avec deux modes pour application sur des SUV (Sport Utility Vehicle. Par ailleurs, le premier véhicule hybride rechargeable la Volt de GM a été introduite sur le marché en 2010. La Volt utilise une architecture qui autorise plusieurs modes : électrique, série et dérivation de

  3. Novel Transverse Flux Machine for Vehicle Traction Applications: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wan, Z.; Ahmed, A.; Husain, I.; Muljadi, E.

    2015-04-02

    A novel transverse flux machine topology for electric vehicle traction applications using ferrite magnets is presented in this paper. The proposed transverse flux topology utilizes novel magnet arrangements in the rotor that are similar to the Halbach array to boost flux linkage; on the stator side, cores are alternately arranged around a pair of ring windings in each phase to make use of the entire rotor flux that eliminates end windings. Analytical design considerations and finite-element methods are used for an optimized design of a scooter in-wheel motor. Simulation results from finite element analysis (FEA) show that the motor achieved comparable torque density to conventional rare-earth permanent magnet (PM) machines. This machine is a viable candidate for direct-drive applications with low cost and high torque density.

  4. Modular PM Motor Drives for Automotive Traction Applications

    International Nuclear Information System (INIS)

    Su, G.J.

    2001-01-01

    This paper presents modular permanent magnet (PM) motor drives for automotive traction applications. A partially modularized drive system consisting of a single PM motor and multiple inverters is described. The motor has multiple three-phase stator winding sets and each winding set is driven with a separate three-phase inverter module. A truly modularized inverter and motor configuration based on an axial-gap PM motor is then introduced, in which identical PM motor modules are mounted on a common shaft and each motor module is powered by a separate inverter module. The advantages of the modular approach for both inverter and motor include: (1) power rating scalability-one design meets different power requirements by simply stacking an adequate number of modules, thus avoiding redesigning and reducing the development cost, (2) increased fault tolerance, and (3) easy repairing. A prototype was constructed by using two inverters and an axial-gap PM motor with two sets of three-phase stat or windings, and it is used to assist the diesel engine in a hybrid electric vehicle converted from a Chevrolet Suburban. The effect of different pulse-width-modulation strategies for both motoring and regenerative modes on current control is analyzed. Torque and regenerative control algorithms are implemented with a digital signal processor. Analytical and initial testing results are included in the paper

  5. Temperature control of power semiconductor devices in traction applications

    Science.gov (United States)

    Pugachev, A. A.; Strekalov, N. N.

    2017-02-01

    The peculiarity of thermal management of traction frequency converters of a railway rolling stock is highlighted. The topology and the operation principle of the automatic temperature control system of power semiconductor modules of the traction frequency converter are designed and discussed. The features of semiconductors as an object of temperature control are considered; the equivalent circuit of thermal processes in the semiconductors is suggested, the power losses in the two-level voltage source inverters are evaluated and analyzed. The dynamic properties and characteristics of the cooling fan induction motor electric drive with the scalar control are presented. The results of simulation in Matlab are shown for the steady state of thermal processes.

  6. Application on forced traction test in surgeries for orbital blowout fracture

    Directory of Open Access Journals (Sweden)

    Bao-Hong Han

    2014-05-01

    Full Text Available AIM: To discuss the application of forced traction test in surgeries for orbital blowout fracture.METHODS: The clinical data of 28 patients with reconstructive surgeries for orbital fracture were retrospectively analyzed. All patients were treated with forced traction test before/in/after operation. The eyeball movement and diplopia were examined and recorded pre-operation, 3 and 6mo after operation, respectively.RESULTS: Diplopia was improved in all 28 cases with forced traction test. There was significant difference between preoperative and post-operative diplopia at 3 and 6mo(PCONCLUSION: Forced traction test not only have a certain clinical significance in diagnosis of orbital blowout fracture, it is also an effective method in improving diplopia before/in/after operation.

  7. Performance Analysis and Simulation of a Novel Brushless Double Rotor Machine for Power-Split HEV Applications

    Directory of Open Access Journals (Sweden)

    Jingang Bai

    2012-01-01

    Full Text Available A new type of brushless double rotor machine (BDRM is proposed in this paper. The BDRM is an important component in compound-structure permanent-magnet synchronous machine (CS-PMSM systems, which are promising for power-split hybrid electric vehicle (HEV applications. The BDRM can realize the speed adjustment between claw-pole rotor and permanent-magnet rotor without brushes and slip rings. The structural characteristics of the BDRM are described and its magnetic circuit model is built. Reactance parameters of the BDRM are deduced by an analytical method. It is found that the size characteristics of the BDRM are different from those of conventional machines. The new sizing and torque equations are analyzed and the theoretical results are used in the optimization process. Studies of the analytical magnetic circuit and finite element method (FEM model show that the BDRM tends to have high leakage flux and low power factor, and then the method to obtain high power factor is discussed. Furthermore, a practical methodology of the BDRM design is developed, which includes an analytical tool, 2D field calculation and performance evaluation by 3D field calculation. Finally, different topologies of the BDRM are compared and an optimum prototype is designed.

  8. HEV and cirrhosis: methods

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. HEV and cirrhosis: methods. Study group. Patients with cirrhosis and recent jaundice for <30 d. Controls. Patients with liver cirrhosis but no recent worsening. Exclusions. Significant alcohol consumption. Recent hepatotoxic drugs. Recent antiviral therapy. Recent ...

  9. Advanced Integrated Traction System

    Energy Technology Data Exchange (ETDEWEB)

    Greg Smith; Charles Gough

    2011-08-31

    The United States Department of Energy elaborates the compelling need for a commercialized competitively priced electric traction drive system to proliferate the acceptance of HEVs, PHEVs, and FCVs in the market. The desired end result is a technically and commercially verified integrated ETS (Electric Traction System) product design that can be manufactured and distributed through a broad network of competitive suppliers to all auto manufacturers. The objectives of this FCVT program are to develop advanced technologies for an integrated ETS capable of 55kW peak power for 18 seconds and 30kW of continuous power. Additionally, to accommodate a variety of automotive platforms the ETS design should be scalable to 120kW peak power for 18 seconds and 65kW of continuous power. The ETS (exclusive of the DC/DC Converter) is to cost no more than $660 (55kW at $12/kW) to produce in quantities of 100,000 units per year, should have a total weight less than 46kg, and have a volume less than 16 liters. The cost target for the optional Bi-Directional DC/DC Converter is $375. The goal is to achieve these targets with the use of engine coolant at a nominal temperature of 105C. The system efficiency should exceed 90% at 20% of rated torque over 10% to 100% of maximum speed. The nominal operating system voltage is to be 325V, with consideration for higher voltages. This project investigated a wide range of technologies, including ETS topologies, components, and interconnects. Each technology and its validity for automotive use were verified and then these technologies were integrated into a high temperature ETS design that would support a wide variety of applications (fuel cell, hybrids, electrics, and plug-ins). This ETS met all the DOE 2010 objectives of cost, weight, volume and efficiency, and the specific power and power density 2015 objectives. Additionally a bi-directional converter was developed that provides charging and electric power take-off which is the first step

  10. Design of salient pole PM synchronous machines for a vehicle traction application. Analysis and implementation

    Energy Technology Data Exchange (ETDEWEB)

    Rilla, M.

    2012-07-01

    This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options. (orig.)

  11. Further demonstration of the VRLA-type UltraBattery under medium-HEV duty and development of the flooded-type UltraBattery for micro-HEV applications

    Energy Technology Data Exchange (ETDEWEB)

    Furukawa, J.; Takada, T.; Monma, D. [The Furukawa Battery Co., Ltd., R and D Division, 23-6 Kuidesaku, Shimofunao-machi, Joban, Iwaki-city, 972-8501 (Japan); Lam, L.T. [CSIRO Energy Technology, Bayview Avenue, Clayton South, Vic. 3169 (Australia)

    2010-02-15

    The UltraBattery has been invented by the CSIRO Energy Technology in Australia and has been developed and produced by the Furukawa Battery Co., Ltd., Japan. This battery is a hybrid energy storage device which combines a super capacitor and a lead-acid battery in single unit cells, taking the best from both technologies without the need of extra, expensive electronic controls. The capacitor enhances the power and lifespan of the lead-acid battery as it acts as a buffer during high-rate discharging and charging, thus enabling it to provide and absorb charge rapidly during vehicle acceleration and braking. The laboratory results of the prototype valve-regulated UltraBatteries show that the capacity, power, available energy, cold cranking and self-discharge of these batteries have met, or exceeded, all the respective performance targets set for both minimum and maximum power-assist HEVs. The cycling performance of the UltraBatteries under micro-, mild- and full-HEV duties is at least four times longer than that of the state-of-the-art lead-acid batteries. Importantly, the cycling performance of UltraBatteries is proven to be comparable or even better than that of the Ni-MH cells. On the other hand, the field trial of UltraBatteries in the Honda Insight HEV shows that the vehicle has surpassed 170,000 km and the batteries are still in a healthy condition. Furthermore, the UltraBatteries demonstrate very good acceptance of the charge from regenerative braking even at high state-of-charge, e.g., 70% during driving. Therefore, no equalization charge is required for the UltraBatteries during field trial. The HEV powered by UltraBatteries gives slightly higher fuel consumption (cf., 4.16 with 4.05 L/100 km) and CO{sub 2} emissions (cf., 98.8 with 96 g km{sup -1}) compared with that by Ni-MH cells. There are no differences in driving experience between the Honda Insight powered by UltraBatteries and by Ni-MH cells. Given such comparable performance, the UltraBattery pack

  12. Advanced state prediction of lithium-ion traction batteries in hybrid and battery electric vehicle applications

    Energy Technology Data Exchange (ETDEWEB)

    Jadidi, Yasser

    2011-07-01

    Automotive power trains with high energy efficiencies - particularly to be found in battery and hybrid electric vehicles - find increasing attention in the focus of reduction of exhaust emissions and increase of mileage. The underlying concept, the electrification of the power train, is subject to the traction battery and its battery management system since the capability of the battery permits and restricts electric propulsion. Consequently, the overall vehicle efficiency and in particular the operation strategy performance strongly depends on the quality of information about the battery. Besides battery technology, the key challenges are given by both the accurate prediction of battery behaviour and the electrochemical battery degradation that leads to power and capacity fade of the traction battery. This book provides the methodology for development of a battery state monitoring and prediction algorithm for application in a battery management system that accounts for the effects of electrochemical degradation. (orig.)

  13. Application of a High-Power Reversible Converter in a Hybrid Traction Power Supply System

    Directory of Open Access Journals (Sweden)

    Gang Zhang

    2017-03-01

    Full Text Available A high-power reversible converter can achieve a variety of functions, such as recovering regenerative braking energy, expanding traction power capacity, and improving an alternating current (AC grid power factor. A new hybrid traction power supply scheme, which consists of a high-power reversible converter and two 12-pulse diode rectifiers, is proposed. A droop control method based on load current feed-forward is adopted to realize the load distribution between the reversible converter and the existing 12-pulse diode rectifiers. The direct current (DC short-circuit characteristics of the reversible converter is studied, then the relationship between the peak fault current and the circuit parameters is obtained from theoretical calculations and validated by computer simulation. The first two sets of 2 MW reversible converters have been successfully applied in Beijing Metro Line 10, the proposed hybrid application scheme and coordinated control strategy are verified, and 11.15% of average energy-savings is reached.

  14. Loss minimization control and efficiency determination of electric drives in traction applications

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, Thomas; Hofmann, Wilfried [Technische Univ. Dresden (Germany). Lehrstuhl fuer Elektrische Maschinen und Antriebe

    2012-11-01

    High-power electric drives in automotive traction applications consume a large part of the disposable electric energy. For this reason the energy efficiency of the drives is of great importance for range and fuel consumption of the hybrid electric vehicle. The paper describes two possible drives with different electric motors from a control point of view. The electric power losses in the drive system are determined depending on the operating point of the machine. With these loss characteristics the control of the drives is optimized to produce minimal losses. Finally the energy efficiency for a realistic urban bus drive cycle is calculated to compare the two types. (orig.)

  15. Dual-Electrical-Port Control of Cascaded Doubly-Fed Induction Machine for EV/HEV Applications

    DEFF Research Database (Denmark)

    Han, Peng; Cheng, Ming; Chen, Zhe

    2017-01-01

    that of the power machine in singly-fed operation mode, and only a half of that of the power machine in doubly-fed operation mode, which shows the urgent need for torque density enhancement of brushless doubly-fed machines for electric vehicle/hybrid electric vehicle applications. Computer simulations...

  16. HEV Test Bench Based on CAN Bus Sensor Communication

    Directory of Open Access Journals (Sweden)

    Shupeng ZHAO

    2014-02-01

    Full Text Available The HEV test bench based on Controller Area Network bus was studied and developed. Control system of HEV power test bench used the CAN bus technology. The application of CAN bus technology on control system development has opened up a new research direction for domestic automobile experimental platform. The HEV power control system development work was completed, including power master controller, electric throttle controller, driving simulation platform, CAN2.0 B communication protocol procedures for formulation, CAN communication monitoring system, the simulation model based on MATLAB code automatic generation technology research, etc. Maximum absorption power of the test bench is 90 kW, the test bench top speed is 6000 r/min, the CAN communication data baud rate is 10~500 k, the conventional electric measurement parameter part precision satisfies the requirement of development of HEV. On the HEV test bench the result of regenerative braking experiment shows that the result got by the test bench was closer to the results got by outdoor road test. And the fuel consumption experiment test results show that the HEV fuel consumption and the charge-discharge character are in linear relationship. The establishment of the test platform for the evaluation of the development of hybrid electric vehicle and power provides physical simulation and test platform.

  17. [The application of delayed skin grafting combined traction in severe joint cicatricial contracture].

    Science.gov (United States)

    Xu, Zihan; Zhang, Zhenxin; Wang, Benfeng; Sun, Yaowen; Guo, Yadong; Gao, Wenjie; Qin, Gaoping

    2014-11-01

    To investigate the effect of delayed skin grafting combined traction in severe joint cicatricial contracture. At the first stage, the joint cicatricial contracture was released completely with protection of vessels, nerves and tendons. The wound was covered with allogenetic skin or biomaterials. After skin traction for 7-14 days, the joint could reach the extension position. Then the skin graft was performed on the wound. 25 cases were treated from Mar. 2000 to May. 2013. Primary healing was achieved at the second stage in all the cases. The skin graft had a satisfactory color and elasticity. Joint function was normal. All the patients were followed up for 3 months to 11 years with no hypertrophic scar and contraction relapse, except for one case who didn' t have enough active exercise on shoulder joint. Delayed skin grafting combined traction can effectively increase the skin graft survival rate and improve the joint function recovery.

  18. HEV

    African Journals Online (AJOL)

    Moatez Billah HARIDA

    Hybrid Electrical Vehicle Model Balance Fidelity and Speed (HEVMBFS) .... introduced to the automatic control engineering community for the ..... Incorporating Engine Transient Characteristics, IEEE transactions on vehicular technology, no.

  19. Indirect Matrix Converter for Hybrid Electric Vehicle Application with Three-Phase and Single-Phase Outputs

    Directory of Open Access Journals (Sweden)

    Yeongsu Bak

    2015-04-01

    Full Text Available This paper presents an indirect matrix converter (IMC topology for hybrid electric vehicle (HEV application with three-phase and single-phase outputs. The HEV includes mechanical, electrical, control, and electrochemical systems among others. In the mechanical system, a traction motor and a compressor motor are used to drive the HEV. The traction motor and the compressor motor are usually operated as three-phase and single-phase motors, respectively. In this respect, a dual AC-drive system can operate the traction and the compressor motor simultaneously. Furthermore, compared to a conventional dual matrix converter system, the proposed topology can reduce the number of switches that the dual outputs share with a DC-link. The application of this system for HEV has advantages, like long lifetime and reduced volume due to the lack of a DC-link. The proposed control strategy and modulation schemes ensure the sinusoidal input and output waveforms and bidirectional power transmission. The proposed system for the HEV application is verified by simulation and experiments.

  20. The application of a clinical prediction rule for patients with neck pain likely to benefit from cervical traction: A case report.

    Science.gov (United States)

    Bernstetter, Andrew

    2016-10-01

    Cervical traction is a commonly utilized intervention in the treatment of patients with neck pain. In 2009, a clinical prediction rule (CPR) was developed as a way to assist clinicians in determining the patient population most likely to respond to cervical traction, though this CPR has yet to be validated. The purpose of this case report is to demonstrate the application of that CPR. The patient was a 46-year-old female with a four-week history of right-sided neck and shoulder pain, with numbness and tingling of her thumb and index finger. Treatment consisted of five sessions provided over 3 weeks. The plan of care included home mechanical cervical traction, exercise, and manual therapy. The patient achieved pain-free cervical range of motion. Neck disability index scores decreased from 28% to 6%, and the Patient-Specific Functional Scale average score improved from 5.5 to 10 out of 10. This case report demonstrates the application of a CPR to assist in deciding if cervical traction is an appropriate intervention. Further research is needed to validate the CPR and to establish the optimal mode of delivery for traction.

  1. Open coil traction system.

    Science.gov (United States)

    Vibhute, Pavankumar Janardan

    2012-01-01

    Sliding mechanics have become a popular method for space closure, with the development of preadjusted edgewise appliances. Furthermore, various space closing auxiliaries have been developed and extensively evaluated for their clinical efficiency. Their effectiveness is enhanced with optimum force magnitude and low load deflection rate/force decay. With the advent of nickel-titanium (Ni-Ti) springs in orthodontics, load deflection rates have been markedly reduced. To use Ni-Ti springs, clinicians have to depend upon prefabricated closed coil springs. The open coil traction system, or open coil retraction spring, is developed utilizing Ni-Ti open coil springs for orthodontic space closure. This article describes the fabrication and clinical application of the open coil traction system, which has a number of advantages. It sustains a low load deflection rate with optimum force magnitude, and its design is adjustable for a desired length and force level. It is fail-safe for both activation and deactivation (ie, it cannot be overactivated, and the decompression limit of the open coil is controlled by the operator). The open coil traction system can be offset from the mucosa to help reduce soft tissue impingement.

  2. Multiple incipient sensor faults diagnosis with application to high-speed railway traction devices.

    Science.gov (United States)

    Wu, Yunkai; Jiang, Bin; Lu, Ningyun; Yang, Hao; Zhou, Yang

    2017-03-01

    This paper deals with the problem of incipient fault diagnosis for a class of Lipschitz nonlinear systems with sensor biases and explores further results of total measurable fault information residual (ToMFIR). Firstly, state and output transformations are introduced to transform the original system into two subsystems. The first subsystem is subject to system disturbances and free from sensor faults, while the second subsystem contains sensor faults but without any system disturbances. Sensor faults in the second subsystem are then formed as actuator faults by using a pseudo-actuator based approach. Since the effects of system disturbances on the residual are completely decoupled, multiple incipient sensor faults can be detected by constructing ToMFIR, and the fault detectability condition is then derived for discriminating the detectable incipient sensor faults. Further, a sliding-mode observers (SMOs) based fault isolation scheme is designed to guarantee accurate isolation of multiple sensor faults. Finally, simulation results conducted on a CRH2 high-speed railway traction device are given to demonstrate the effectiveness of the proposed approach. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

  3. Hepatitis E Virus (HEV) Infection in Ireland

    LENUS (Irish Health Repository)

    Hickey, C

    2016-09-01

    Hepatitis E virus (HEV) is a single stranded RNA virus causing infection worldwide. In developing countries HEV genotypes 1 and 2 spread faeco-orally via water. Recently, infections with HEV have been detected in Europe and North America in patients with no travel history. These are food-borne HEV genotypes 3 and 4, a pig-associated zoonosis. Most infections are asymptomatic but morbidity and chronic infection may occur with prior liver disease or immunosuppression. International seroprevalence rates vary and with improved diagnostics have increased. To determine the current prevalence in this region we studied anonymised serum samples submitted in 2015 for routine testing. We detected anti-HEV IgG in 16\\/198 (8%) individuals, highest rate in 40-59 year olds (43.8%). This is higher than reported for the same region in 1995 (0.4%) using a previous generation assay. This study provides evidence of HEV circulation in Ireland and reinforces the need for ongoing surveillance.

  4. Design Analysis of Taper Width Variations in Magnetless Linear Machine for Traction Applications

    Directory of Open Access Journals (Sweden)

    Saadha Aminath

    2018-01-01

    Full Text Available Linear motors are being used in a different application with a huge popularity in the use of transport industry. With the invention of maglev trains and other high-speed trains, linear motors are being used for the translation and braking applications for these systems. However, a huge drawback of the linear motor design is the cogging force, low thrust values, and voltage ripples. This paper aims to study the force analysis with change in taper/teeth width of the motor stator and mover to understand the best teeth ratio to obtain a high flux density and a high thrust. The analysis is conducted through JMAG software and it is found that the optimum teeth ratio for both the stator and mover gives an increase of 94.4% increases compared to the 0.5mm stator and mover width.

  5. Optimal Rule-Based Power Management for Online, Real-Time Applications in HEVs with Multiple Sources and Objectives: A Review

    Directory of Open Access Journals (Sweden)

    Bedatri Moulik

    2015-08-01

    Full Text Available The field of hybrid vehicles has undergone intensive research and development, primarily due to the increasing concern of depleting resources and increasing pollution. In order to investigate further options to optimize the performance of hybrid vehicles with regards to different criteria, such as fuel economy, battery aging, etc., a detailed state-of-the-art review is presented in this contribution. Different power management and optimization techniques are discussed focusing on rule-based power management and multi-objective optimization techniques. The extent of rule-based power management and optimization in solving battery aging issues is investigated along with an implementation in real-time driving scenarios where no pre-defined drive cycle is followed. The goal of this paper is to illustrate the significance and applications of rule-based power management optimization based on previous contributions.

  6. Frequency of HEV contamination in sewerage waters in Pakistan.

    Science.gov (United States)

    Ahmad, Tahir; Waheed, Yasir; Tahir, Sadia; Safi, Sher Zaman; Fatima, Kaneez; Afzal, Muhammad Sohail; Farooqi, Zia-ur-Rehman; Qadri, Ishtiaq

    2010-12-23

    Enteric viruses, including Hepatitis E virus (HEV), are able to persist under environmental conditions and may cause public health problems by contaminating natural and drinking water resources. Routine procedures for monitoring viruses in water samples have not been established for the water microbiology screening panel. Eighty-six raw sewerage samples were collected from the different regions of Islamabad and Rawalpindi, the twin cities of Pakistan. Samples were concentrated for HEV, using a polyethylene glycol-based method followed by viral RNA extraction using a commercial kit-based method. Reverse transcription polymerase chain reaction (RT-PCR) with HEV specific primers was used for the detection of HEV. The present investigation focused on 86 raw sewerage water samples taken from different locations of drainage outlets of Islamabad and Rawalpindi. After careful experimentation, 35 samples were found to be RT-PCR positive.  Nineteen (44.7%) out of 47 samples from Rawalpindi city were HEV positive while 16 (41.02%) out of 39 samples from Islamabad were HEV positive. All positive samples were found in the highly congested areas. The high detection rate of HEV in this study shows that HEV circulates at a relatively high frequency in the sewerage waters in Pakistan. This study is the first report on detection of HEV from sewerage waste water from Pakistan and suggests that HEV might be a potent indicator of viral pollution in environmental specimens.

  7. Regression analysis of traction characteristics of traction fluids

    Science.gov (United States)

    Loewenthal, S. H.; Rohn, D. A.

    1983-01-01

    Traction data for Santotrac 50 and TDF-88 over a wide range of operating conditions were analyzed. An eight term correlation equation to predict the maximum traction coefficient and a six term correlation equation to predict the initial slope of the traction curve were developed. The slope correlation was corrected for size effect considering the compliance of the disks. The effects of different operating conditions on the traction performance of each traction fluid were studied. Both fluids exhibited a loss in traction with increases in spin, but the losses with the TDF-88 fluid were not as severe as those with Santotrac 50. Overall, both fluids exhibited similar performance, showing an increase in traction with contact pressure up to about 2.0 GPa, and a reduction in traction with higher surface speeds up to about 100 m/sec. The apparent stiffness of the traction contact, that is, film disk combination, increases with contact pressure and decreases with speed.

  8. Hepatitis E virus (HEV) genotype 3 infection of human liver chimeric mice as a model for chronic HEV infection

    NARCIS (Netherlands)

    M.D.B. van de Garde (Martijn D.B.); S.D. Pas (Suzan); Van Der Net, G. (Guido); R.A. de Man (Robert); A.D.M.E. Osterhaus (Albert); B.L. Haagmans (Bart); P.A. Boonstra (André); T. Vanwolleghem (Thomas)

    2016-01-01

    textabstractGenotype 3 (gt3) hepatitis E virus (HEV) infections are emerging in Western countries. Immunosuppressed patients are at risk of chronic HEV infection and progressive liver damage, but no adequate model system currently mimics this disease course. Here we explore the possibilities of in

  9. Control strategy minimizing the converter-alternating current motor losses: application to electric traction; Strategies de commande minimisant les pertes d'un ensemble convertisseur - machine alternative: application a la traction electrique

    Energy Technology Data Exchange (ETDEWEB)

    Bastiani, Ph.

    2001-02-01

    Improving the efficiency of the converter-alternating current motor system is a major task in electric traction. Global energy optimisation implies a specific approach at system scale. To reach this goal, we have chosen an algebraic method using sub-system models. To start with, a synchronous machine Park model is developed to take account magnetic saturation and iron losses. Then, an averaged model of the voltage inverter is used in order to obtain a simplified model of the losses to be implemented in our optimisation method. This is how the global model is built including losses in the synchronous machine along with the losses of the power converter. Experimental results are there to validate our approach. This study proposes a method based on algebraic formulation of the general laws to control torque. Algorithms take into account magnetic circuits saturation and power losses in both the machine and its converter. Here again, experimental results validate the algorithm on several test benches. Achieved efficiency improvement is important compared to existing usual control strategies. The proposed method can be generalised to other machine-converter systems. As a matter of fact we have extended our study to the induction machine. As a complement ti this study we have looked at the effects natural limitations of voltages and currents in the torque-speed plane. Therefore algebraic formulation of the torque-speed plane and optimisation strategies are proposed including those constraints. (author)

  10. Elastic model of the traction behavior of two traction lubricants

    Science.gov (United States)

    Loewenthal, S. H.; Rohn, D. A.

    1984-01-01

    In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

  11. [Assessment of a transfusion emergent risk: the case of HEV].

    Science.gov (United States)

    Pillonel, J; Gallian, P; Sommen, C; Couturier, E; Piquet, Y; Djoudi, R; Laperche, S

    2014-11-01

    The risk assessment for blood transfusion is an essential step that must precede any screening strategy of a pathogen transmitted by transfusion. After several cases of HEV transmission by transfusion in France, a risk assessment for this virus was performed. We used a method based on the prevalence of HEV-RNA in plasmas collected for the preparation of SD-plasma. To estimate the rate of HEV-RNA positive among all blood donations, data on SD-plasma were adjusted on the following HEV risk factors: gender, age group and region of residence. We assumed that HEV risk factors were the same in plasma donors and whole blood donors. Among 57,101 plasma donations tested for HEV-RNA in 2013, 24 were positive (crude rate of 4.2 per 10,000 donations). After adjustment, the total number of HEV-RNA positive blood donations was estimated at 788, accounting for a rate of 2.65 per 10,000 donations (95% CI: 1.6-3.7) or 1 in 3800 donations (1 in 6,200-1 in 2,700). This rate was 12 times higher in men than in women, increased with age, and varied according to region of residence. The risk of blood donation contamination by HEV has been estimated to be 1 in 3800 donations in 2013. An essential input is still missing to assess now the risk in recipients: the minimum infectious dose. Furthermore, the risk in recipients has to be analyzed according to characteristics of transfused patients: presence of anti-HEV immunity, existence of chronic liver disease or immunodeficiency. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

  12. Hev b 11, a peculiar class I chitinase?

    NARCIS (Netherlands)

    Beintema, J. J.

    2007-01-01

    The recently identified rubber allergen Hev b 11, which is a class I chitinase, may be a cytosolic (C-serum) protein. This is a rather unique feature, as all other known plant class I chitinases are vacuolar proteins.

  13. Alignment of displaced or impacted teeth with the traction chain.

    Science.gov (United States)

    Sander, Franz Martin; Sander, Christian; Sander, Franz Günter

    2006-07-01

    To align those teeth in the dental arch that cannot erupt or are displaced, they must be surgically exposed. After the traction device is attached, the tooth is again covered with the mucoperiosteal flap to protect the tissues involved. For this reason, the loss of this traction device must be absolutely avoided in order to prevent another surgical intervention. Here at the University of Ulm, we have developed and tested an optimized traction chain for that purpose. The chain is attached to the tooth with a laser-roughened pad applying the acid-etching technique. The chain links serve as fixation elements for traction devices such as elastic ligatures or piggyback archwires. At the same time, one can determine the distance covered by the tooth by the number of the erupting chain links. We demonstrate the clinical application of this traction device in two cases.

  14. A Recombinant HAV Expressing a Neutralization Epitope of HEV Induces Immune Response against HAV and HEV in Mice.

    Science.gov (United States)

    Xiang, Kui; Kusov, Yuri; Ying, Guan; Yan, Wang; Shan, Yi; Jinyuan, Wu; Na, Yin; Yan, Zhou; Hongjun, Li; Maosheng, Sun

    2017-09-15

    Hepatitis A virus (HAV) and hepatitis E virus (HEV) are causative agents of acute viral hepatitis transmitted via the fecal-oral route. Both viruses place a heavy burden on the public health and economy of developing countries. To test the possibility that HAV could be used as an expression vector for the development of a combination vaccine against hepatitis A and E infections, recombinant HAV-HEp148 was created as a vector to express an HEV neutralization epitope (HEp148) located at aa 459-606 of the HEV capsid protein. The recombinant virus expressed the HEp148 protein in a partially dimerized state in HAV-susceptible cells. Immunization with the HAV-HEp148 virus induced a strong HAV- and HEV-specific immune response in mice. Thus, the present study demonstrates a novel approach to the development of a combined hepatitis A and E vaccine.

  15. An advanced pitch change mechanism incorporating a hybrid traction drive

    Science.gov (United States)

    Steinetz, B. M.; Loewenthal, S. H.; Sargisson, D. F.; White, G.

    1984-01-01

    A design of a propeller pitch control mechanism is described that meets the demanding requirements of a high-power, advanced turboprop. In this application, blade twisting moment torque can be comparable to that of the main reduction gearbox output: precise pitch control, reliability and compactness are all at a premium. A key element in the design is a compact, high-ratio hybrid traction drive which offers low torque ripple and high torsional stiffness. The traction drive couples a high speed electric motor/alternator unit to a ball screw that actuates the blade control links. The technical merits of this arrangement and the performance characteristics of the traction drive are discussed.

  16. Electromagnetic Comparison of 3-, 5- and 7-phases Permanent-Magnet Synchronous Machines : Mild Hybrid Traction Application

    Directory of Open Access Journals (Sweden)

    D. Ouamara

    2016-09-01

    Full Text Available Authors compare the electromagnetic performances of three multi-phases permanent-magnet (PM synchronous machines (PMSM for Mild Hybridtraction application. This comparison was made using two-dimensional (2-D numerical simulations in transient magnetic with eddy-current reaction field in the PMs. The best machine was determined using an energetic analysis (i.e., losses, torque and efficiency according specifications. In this study, the non-overlapping winding with double layer (i.e. all teeth wound type was used. The winding synthesis is based on the "Star of slots" method as well as the Fourier series decomposition of the magnetomotive force (MMF.

  17. Integral Sensor Fault Detection and Isolation for Railway Traction Drive.

    Science.gov (United States)

    Garramiola, Fernando; Del Olmo, Jon; Poza, Javier; Madina, Patxi; Almandoz, Gaizka

    2018-05-13

    Due to the increasing importance of reliability and availability of electric traction drives in Railway applications, early detection of faults has become an important key for Railway traction drive manufacturers. Sensor faults are important sources of failures. Among the different fault diagnosis approaches, in this article an integral diagnosis strategy for sensors in traction drives is presented. Such strategy is composed of an observer-based approach for direct current (DC)-link voltage and catenary current sensors, a frequency analysis approach for motor current phase sensors and a hardware redundancy solution for speed sensors. None of them requires any hardware change requirement in the actual traction drive. All the fault detection and isolation approaches have been validated in a Hardware-in-the-loop platform comprising a Real Time Simulator and a commercial Traction Control Unit for a tram. In comparison to safety-critical systems in Aerospace applications, Railway applications do not need instantaneous detection, and the diagnosis is validated in a short time period for reliable decision. Combining the different approaches and existing hardware redundancy, an integral fault diagnosis solution is provided, to detect and isolate faults in all the sensors installed in the traction drive.

  18. Subcellular localization of hepatitis E virus (HEV) replicase

    International Nuclear Information System (INIS)

    Rehman, Shagufta; Kapur, Neeraj; Durgapal, Hemlata; Panda, Subrat Kumar

    2008-01-01

    Hepatitis E virus (HEV) is a hepatotropic virus with a single sense-strand RNA genome of ∼ 7.2 kb in length. Details of the intracellular site of HEV replication can pave further understanding of HEV biology. In-frame fusion construct of functionally active replicase-enhanced green fluorescent protein (EGFP) gene was made in eukaryotic expression vector. The functionality of replicase-EGFP fusion protein was established by its ability to synthesize negative-strand viral RNA in vivo, by strand-specific anchored RT-PCR and molecular beacon binding. Subcellular co-localization was carried out using organelle specific fluorophores and by immuno-electron microscopy. Fluorescence Resonance Energy Transfer (FRET) demonstrated the interaction of this protein with the 3' end of HEV genome. The results show localization of replicase on the endoplasmic reticulum membranes. The protein regions responsible for membrane localization was predicted and identified by use of deletion mutants. Endoplasmic reticulum was identified as the site of replicase localization and possible site of replication

  19. seroprevalence of hav, hbv, hcv, and hev among acute hepatitis

    African Journals Online (AJOL)

    2013-07-30

    =1); IgM anti-HBc and IgM anti-HEV 1% (n=1); IgM anti-HBc and ... Viral hepatitis is a recognised major public health ... of HBV carriers varies substantially between regions, ... standards of sanitation promote the transmission.

  20. Footwear traction and lower extremity noncontact injury.

    Science.gov (United States)

    Wannop, John W; Luo, Geng; Stefanyshyn, Darren J

    2013-11-01

    Football is the most popular high school sport; however, it has the highest rate of injury. Speculation has been prevalent that foot fixation due to high footwear traction contributes to injury risk. Therefore, the purpose of the study was to determine whether a relationship exists between the athlete's specific footwear traction (measured with their own shoes on the field of play) and lower extremity noncontact injury in high school football. For 3 yr, 555 high school football athletes had their footwear traction measured on the actual field of play at the start of the season, and any injury the athletes suffered during a game was recorded. Lower extremity noncontact injury rates, grouped based on the athlete's specific footwear traction (both translational and rotational), were compared. For translational traction, injury rate reached a peak of 23.3 injuries/1000 game exposures within the midrange of translational traction, before decreasing to 5.0 injuries/1000 game exposures in the high range of traction. For rotational traction, there was a steady increase in injury rate as footwear traction increased, starting at 4.2 injuries/1000 game exposures at low traction and reaching 19.2 injuries/1000 game exposures at high traction. A relationship exists between footwear traction and noncontact lower extremity injury, with increases in rotational traction leading to a greater injury rate and increases in translational traction leading to a decrease in injury. It is recommended that athletes consider selecting footwear with the lowest rotational traction values for which no detriment in performance results.

  1. Methodology of system design in electrical engineering with Bond Graph: application on a railway traction system; Methodologie de conception systemique en genie electrique a l'aide de l'outil Bond Graph: application a une chaine de traction ferroviaire

    Energy Technology Data Exchange (ETDEWEB)

    Gandanegara, G.

    2003-11-15

    In Electrical Engineering, the global analysis of systems is difficult because of their heterogeneity and their multi-domain nature. Nevertheless, this system approach is essential because it underlines couplings between elements of different physical fields. To facilitate this analysis, the unified formalism Bond Graph is used. This modeling method illustrates the energetic transfers in the system. Moreover, this methodology offers interesting solutions in terms of system analysis. Two simplification methods have been investigated and compared, i.e. the Singular Perturbations Method (SPM), based on the dynamic analysis of elements, and the Model Order Reduction Algorithm (MORA), based on the energetic activity. By these methods, a simplified bond graph model can be obtained for a given frequency range. The stability analysis by the root locus method and the Lyapunov's second method have been examined and applied with the Bond Graph formalism support. An industrial railway traction system is considered as the case study in the application of these different analysis techniques. (author)

  2. A New Hybrid Power Configuration Used In HEV And Development of Its Driving BLDC

    Directory of Open Access Journals (Sweden)

    Yanliang Xu

    2013-07-01

    Full Text Available Hybrid electric vehicle (HEV that has the advantages of high performance, high fuel efficiency, low emissions, and long operating range is focused on nowadays. A new hybrid power configuration used in HEV is presented with different control strategies and HEV performances when equipping different weight of fuel power and battery one. In order to realize the new hybrid power configuration especially in the refitted HEV, fractional-slot concentrated-wingding BLDC with higher rated spinning speed is given and the prototyped one is developed and fabricated which satisfy successfully the requirements of high performance and demission restriction for the refitted HEV.

  3. Estimation of hepatitis E virus (HEV) pig seroprevalence using Elisa and Western blot and comparison between human and pig HEV sequences in Belgium.

    NARCIS (Netherlands)

    Thiry, D.; Mauroy, A.; Saegerman, C.; Thomas, I.; Wautier, M.; Miry, C.; Czaplicki, G.; Berkvens, D.; Praet, N.; Poel, van der W.H.M.; Cariolet, R.; Brochier, B.; Thiry, E.

    2014-01-01

    Zoonotic transmission of hepatitis E virus (HEV) is of special concern, particularly in high income countries were waterborne infections are less frequent than in developing countries. High HEV seroprevalences can be found in European pig populations. The aims of this study were to obtain prevalence

  4. Replication of hepatitis E virus in the ovary and promotion of oocyte apoptosis in rabbits infected with HEV-4

    OpenAIRE

    An, Junqing; Liu, Tianlong; She, Ruiping; Wu, Qiaoxing; Tian, Jijing; Shi, Ruihan; Hao, Wenzhuo; Ren, Xinxin; Yang, Yue; Lu, Yiyao; Yang, Yifei; Wu, Yuanheng

    2017-01-01

    Hepatitis E virus (HEV) infection can induce infertility and miscarriage in pregnant women and infect neonates through vertical transmission. However, the mechanism of infertility and vertical transmission remains unclear. In the present study, we evaluated the replication of HEV in the ovary and structural and molecular changes induced by HEV after intraperitoneal injection of HEV in rabbits. Positive- and negative-strand HEV RNA was detected in the ovaries at 28 and 49 days post-infection. ...

  5. HEV-positive blood donations represent a relevant infection risk for immunosuppressed recipients.

    Science.gov (United States)

    Westhölter, Dirk; Hiller, Jens; Denzer, Ulrike; Polywka, Susanne; Ayuk, Francis; Rybczynski, Meike; Horvatits, Thomas; Gundlach, Svantje; Blöcker, Johanna; Schulze Zur Wiesch, Julian; Fischer, Nicole; Addo, Marylyn M; Peine, Sven; Göke, Burkhard; Lohse, Ansgar W; Lütgehetmann, Marc; Pischke, Sven

    2018-03-15

    Routine HEV testing of blood products has recently been implemented in Great Britain and the Netherlands. The relevance of transfusion-transmitted HEV infections is still controversially discussed in Europe. All blood donations at the University Medical Center Hamburg-Eppendorf were prospectively tested for HEV RNA by pooled PCR from October 2016 to May 2017. Reactive samples were individually retested. Additionally, stored samples from previous donations of positive donors were tested to determine the duration of HEV viraemia. HEV RNA-positive donors and a control cohort were asked to answer a questionnaire. Twenty-three out of 18,737 HEV RNA-positive donors were identified (0.12%). Only two of the positive donors (8.7%) presented with elevated aminotransferases at time of donation (alanine aminotransferase: 192 and 101 U/L). The retrospective analysis of all positive donors revealed that four asymptomatic donors had been HEV viraemic for up to three months with the longest duration of HEV viraemia exceeding four months. Despite the HEV-testing efforts, 14 HEV RNA-positive blood products were transfused into 12 immunocompromised and two immunocompetent patients. One recipient of these products developed fatal acute-on-chronic liver failure complicated by Pseudomonas septicemia. The questionnaire revealed that HEV RNA-positive donors significantly more often consumed raw pork meat (12 out of 18; 67%) than controls (89 out of 256; 35%; p = 0.01). In two donors, undercooked pork liver dishes were identified as the source of infection. HEV genotyping was possible in 7 out of 23 of HEV viraemic donors and six out of seven isolates belonged to HEV Genotype 3, Group 2. Prolonged HEV viraemia can be detected at a relatively high rate in Northern German blood donors, leading to transfusion-transmitted HEV infections in several patients with the risk of severe and fatal complications. Eating raw pork tartare represented a relevant risk for the acquisition of HEV

  6. cDNA encoding a polypeptide including a hev ein sequence

    Energy Technology Data Exchange (ETDEWEB)

    Raikhel, Natasha V. (Okemos, MI); Broekaert, Willem F. (Dilbeek, BE); Chua, Nam-Hai (Scarsdale, NY); Kush, Anil (New York, NY)

    2000-07-04

    A cDNA clone (HEV1) encoding hevein was isolated via polymerase chain reaction (PCR) using mixed oligonucleotides corresponding to two regions of hevein as primers and a Hevea brasiliensis latex cDNA library as a template. HEV1 is 1018 nucleotides long and includes an open reading frame of 204 amino acids. The deduced amino acid sequence contains a putative signal sequence of 17 amino acid residues followed by a 187 amino acid polypeptide. The amino-terminal region (43 amino acids) is identical to hevein and shows homology to several chitin-binding proteins and to the amino-termini of wound-induced genes in potato and poplar. The carboxyl-terminal portion of the polypeptide (144 amino acids) is 74-79% homologous to the carboxyl-terminal region of wound-inducible genes of potato. Wounding, as well as application of the plant hormones abscisic acid and ethylene, resulted in accumulation of hevein transcripts in leaves, stems and latex, but not in roots, as shown by using the cDNA as a probe. A fusion protein was produced in E. coli from the protein of the present invention and maltose binding protein produced by the E. coli.

  7. Counter traction makes endoscopic submucosal dissection easier.

    Science.gov (United States)

    Oyama, Tsuneo

    2012-11-01

    Poor counter traction and poor field of vision make endoscopic submucosal dissection (ESD) difficult. Good counter traction allows dissections to be performed more quickly and safely. Position change, which utilizes gravity, is the simplest method to create a clear field of vision. It is useful especially for esophageal and colon ESD. The second easiest method is clip with line method. Counter traction made by clip with line accomplishes the creation of a clear field of vision and suitable counter traction thereby making ESD more efficient and safe. The author published this method in 2002. The name ESD was not established in those days; the name cutting endoscopic mucosal resection (EMR) or EMR with hook knife was used. The other traction methods such as external grasping forceps, internal traction, double channel scope, and double scopes method are introduced in this paper. A good strategy for creating counter traction makes ESD easier.

  8. Wheel Slip Control for Improving Traction-Ability and Energy Efficiency of a Personal Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Kanghyun Nam

    2015-07-01

    Full Text Available In this paper, a robust wheel slip control system based on a sliding mode controller is proposed for improving traction-ability and reducing energy consumption during sudden acceleration for a personal electric vehicle. Sliding mode control techniques have been employed widely in the development of a robust wheel slip controller of conventional internal combustion engine vehicles due to their application effectiveness in nonlinear systems and robustness against model uncertainties and disturbances. A practical slip control system which takes advantage of the features of electric motors is proposed and an algorithm for vehicle velocity estimation is also introduced. The vehicle velocity estimator was designed based on rotational wheel dynamics, measurable motor torque, and wheel velocity as well as rule-based logic. The simulations and experiments were carried out using both CarSim software and an experimental electric vehicle equipped with in-wheel-motors. Through field tests, traction performance and effectiveness in terms of energy saving were all verified. Comparative experiments with variations of control variables proved the effectiveness and practicality of the proposed control design.

  9. Traction for low-back pain with or without sciatica.

    Science.gov (United States)

    Wegner, Inge; Widyahening, Indah S; van Tulder, Maurits W; Blomberg, Stefan E I; de Vet, Henrica Cw; Brønfort, Gert; Bouter, Lex M; van der Heijden, Geert J

    2013-08-19

    physiotherapy alone or when comparing traction with other treatments, there was very-low- to moderate-quality evidence that traction may make little or no difference in pain intensity, functional status or global improvement.For people with LBP with sciatica and acute, subacute or chronic pain, there was low- to moderate-quality evidence that traction probably has no impact on pain intensity, functional status or global improvement. This was true when traction was compared with controls and other treatments, as well as when the combination of traction plus physiotherapy was compared with physiotherapy alone. No studies reported the effect of traction on return to work.For chronic LBP without sciatica, there was moderate-quality evidence that traction probably makes little or no difference in pain intensity when compared with sham treatment. No studies reported on the effect of traction on functional status, global improvement or return to work.Adverse effects were reported in seven of the 32 studies. These included increased pain, aggravation of neurological signs and subsequent surgery. Four studies reported that there were no adverse effects. The remaining studies did not mention adverse effects. These findings indicate that traction, either alone or in combination with other treatments, has little or no impact on pain intensity, functional status, global improvement and return to work among people with LBP. There is only limited-quality evidence from studies with small sample sizes and moderate to high risk of bias. The effects shown by these studies are small and are not clinically relevant. Implications for practice To date, the use of traction as treatment for non-specific LBP cannot be motivated by the best available evidence. These conclusions are applicable to both manual and mechanical traction. Implications for research Only new, large, high-quality studies may change the point estimate and its accuracy, but it should be noted that such change may not necessarily

  10. Optical projection tomography reveals dynamics of HEV growth after immunization with protein plus CFA and features shared with HEVs in acute autoinflammatory lymphadenopathy.

    Science.gov (United States)

    Kumar, Varsha; Chyou, Susan; Stein, Jens V; Lu, Theresa T

    2012-01-01

    The vascular-stromal compartment of lymph nodes is important for lymph node function, and high endothelial venules (HEVs) play a critical role in controlling the entry of recirculating lymphocytes. In autoimmune and autoinflammatory diseases, lymph node swelling is often accompanied by apparent HEV expansion and, potentially, targeting HEV expansion could be used therapeutically to limit autoimmunity. In previous studies using mostly flow cytometry analysis, we defined three differentially regulated phases of lymph node vascular-stromal growth: initiation, expansion, and the re-establishment of vascular quiescence and stabilization. In this study, we use optical projection tomography to better understand the morphologic aspects of HEV growth upon immunization with ovalbumin/CFA (OVA/CFA). We find HEV elongation as well as modest arborization during the initiation phase, increased arborization during the expansion phase, and, finally, vessel narrowing during the re-establishment of vascular quiescence and stabilization. We also examine acutely enlarged autoinflammatory lymph nodes induced by regulatory T cell depletion and show that HEVs are expanded and morphologically similar to the expanded HEVs in OVA/CFA-stimulated lymph nodes. These results reinforce the idea of differentially regulated, distinct phases of vascular-stromal growth after immunization and suggest that insights gained from studying immunization-induced lymph node vascular growth may help to understand how the lymph node vascular-stromal compartment could be therapeutically targeted in autoimmune and autoinflammatory diseases.

  11. Optical projection tomography reveals dynamics of HEV growth after immunization with protein plus CFA and features shared with HEVs in acute autoinflammatory lymphadenopathy

    Directory of Open Access Journals (Sweden)

    Varsha eKumar

    2012-09-01

    Full Text Available The vascular-stromal compartment of lymph nodes is important for lymph node function, and high endothelial venules (HEVs play a critical role in controlling the entry of recirculating lymphocytes. In autoimmune and autoinflammatory diseases, lymph node swelling is often accompanied by apparent HEV expansion and, potentially, targeting HEV expansion could be used therapeutically to limit autoimmunity. In previous studies using mostly flow cytometry analysis, we defined 3 differentially regulated phases of lymph node vascular-stromal growth: initiation, expansion, and the re-establishment of vascular quiescence and stabilization. In this study, we use optical projection tomography to better understand the morphologic aspects of HEV growth upon immunization with ovalbumin/CFA. We find HEV elongation as well as modest arborization during the initiation phase, increased arborization during the expansion phase, and, finally, vessel narrowing during the re-establishment of vascular quiescence and stabilization. We also examine acutely enlarged autoinflammatory lymph nodes induced by regulatory T cell depletion and show that HEVs are expanded and morphologically similar to the expanded HEVs in OVA/CFA-stimulated lymph nodes. These results reinforce the idea of differentially regulated, distinct phases of vascular-stromal growth after immunization and suggest that insights gained from studying immunization-induced lymph node vascular growth may help to understand how the lymph node vascular-stromal compartment could be therapeutically targeted in autoimmune and autoinflammatory diseases.

  12. [Assessment of rehabilitation progress in patients with cervical radicular pain syndrome after application of high intensity laser therapy - HILT and Saunders traction device].

    Science.gov (United States)

    Haładaj, Robert; Pingot, Julia; Pingot, Mariusz

    2015-07-01

    Osteoarthritis of the spine is a major global health problem, it is an epidemic of our times. It affects all parts of the spine, but the hardest to treat is its cervical region. The cervical spine is most mobile, delicate and sensitive to any load. It requires special care in conservative treatment. To date the selection of effective therapeutic approaches has been controversial. The aim of the study was to assess the progress of rehabilitation in patients with cervical radicular pain syndrome after using two different methods of treatment: HILT and spinal axial traction with the use of Saunders device. The randomized study included 150 patients (81 women and 69 men, aged 24-67 years, mean age 45.5) divided into two groups of 75 patients each with characteristic symptoms of radicular pain. The measurement of the range of cervical spine movement of the cervical spine, visual analog scale for pain - VAS and a NDI questionnaire (Neck Disability Index - Polish version) - an indicator of functional disorders - were used to evaluate the effectiveness of the two different therapies. The results obtained by Saunders method remained significantly higher than those obtained when HILT laser therapy was used for most of the examined parameters. A thorough analysis of the results showed greater analgesic efficacy, improved global mobility and reduced functional impairment in patients treated with Saunders method. Both therapeutic methods manifest analgesic effect and a positive impact on the improvement of range of cervical spine movement in patients with radicular pain in this spine region. HILT laser therapy and Saunders traction device reduce neck disability index in the treated patients. © 2015 MEDPRESS.

  13. Plica neuropathica causing traction alopecia

    Directory of Open Access Journals (Sweden)

    K Pavithran

    1990-01-01

    Full Text Available A middle aged woman developed matting of the hairs of the scalp following use of a home made shampoo that contained leaves of Hibiscus rosasiensis. The entangled and matted hair mass in the occipital region pulled hairs of the vertex region of the scalp, resulting in a patch of traction alopecia. Release of tension on the hairs by cutting them with scissors prevented further extension of alopecia.

  14. Traction control of an electric formula student racing car

    NARCIS (Netherlands)

    Loof, J.W.; Besselink, I.J.M.; Nijmeijer, H.

    2014-01-01

    This article describes the design of a traction control system in an electric Formula Student vehicle. In many race applications the accelerator pedal is difficult to control for an in-experienced driver, especially in the case of electric vehicles, where a large torque is available from standstill.

  15. Counter Traction Makes Endoscopic Submucosal Dissection Easier

    OpenAIRE

    Oyama, Tsuneo

    2012-01-01

    Poor counter traction and poor field of vision make endoscopic submucosal dissection (ESD) difficult. Good counter traction allows dissections to be performed more quickly and safely. Position change, which utilizes gravity, is the simplest method to create a clear field of vision. It is useful especially for esophageal and colon ESD. The second easiest method is clip with line method. Counter traction made by clip with line accomplishes the creation of a clear field of vision and suitable co...

  16. Traction Control System for Motorcycles

    Directory of Open Access Journals (Sweden)

    Cardinale Pascal

    2009-01-01

    Full Text Available Traction control is a widely used control system to increase stability and safety of four wheel vehicles. Automatic stability control is used in the BMW K1200R motorcycle and in motoGP competition, but not in other motorcycles. This paper presents an algorithm and a low-cost real-time hardware implementation for motorcycles. A prototype has been developed, applied on a commercial motorcycle, and tested in a real track. The control system that can be tuned by the driver during the race has been appreciated by the test driver.

  17. Advanced dc-Traction-Motor Control System

    Science.gov (United States)

    Vittone, O.

    1985-01-01

    Motor-control concept for battery-powered vehicles includes stateof-the-art power-transistor switching and separate excitation of motor windings in traction and regenerative braking. Switching transistors and other components of power-conditioning subsystem operate under control of computer that coordinates traction, braking, and protective functions.

  18. Elastohydrodynamic Traction Properties of Seed Oils

    Science.gov (United States)

    The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and s...

  19. Elastohydrodynamic (EHD) traction properties of seed oils

    Science.gov (United States)

    The elastohydrodynamic traction coefficient (tc) properties of nine seed oils of varying chemical structures, PAO and hexadecane, were investigated using a ball-on disk traction apparatus. The seed oils were: castor oil, a triglyceride with hydroxyl functional group; jojoba, a monoglyceride; and sev...

  20. Analysis methods of stochastic transient electro–magnetic processes in electric traction system

    Directory of Open Access Journals (Sweden)

    T. M. Mishchenko

    2013-04-01

    Full Text Available Purpose. The essence and basic characteristics of calculation methods of transient electromagnetic processes in the elements and devices of non–linear dynamic electric traction systems taking into account the stochastic changes of voltages and currents in traction networks of power supply subsystem and power circuits of electric rolling stock are developed. Methodology. Classical methods and the methods of non–linear electric engineering, as well as probability theory method, especially the methods of stationary ergodic and non–stationary stochastic processes application are used in the research. Findings. Using the above-mentioned methods an equivalent circuit and the system of nonlinear integra–differential equations for electromagnetic condition of the double–track inter-substation zone of alternating current electric traction system are drawn up. Calculations allow obtaining electric traction current distribution in the areas of feeder zones. Originality. First of all the paper is interesting and important from scientific point of view due to the methods, which allow taking into account probabilistic character of change for traction voltages and electric traction system currents. On the second hand the researches develop the most efficient methods of nonlinear circuits’ analysis. Practical value. The practical value of the research is presented in application of the methods to the analysis of electromagnetic and electric energy processes in the traction power supply system in the case of high-speed train traffic.

  1. Robust equivalent consumption-based controllers for a dual-mode diesel parallel HEV

    International Nuclear Information System (INIS)

    Finesso, Roberto; Spessa, Ezio; Venditti, Mattia

    2016-01-01

    Highlights: • Non-plug-in dual-mode parallel hybrid architecture. • Cross-validation machine-learning for robust equivalent consumption-based controllers. • Optimal control strategy based on fuel consumption, NOx and battery aging. • Impact of different equivalent consumption definitions on HEV performance. • Correlation between vehicle braking energy and SOC variation in the traction stages. - Abstract: New equivalent consumption minimization strategy (ECMS) tools have been developed and applied to identify the optimal control strategy of a dual-mode parallel hybrid electric vehicle equipped with a compression-ignition engine. In this architecture, the electric machine is coupled to the engine through either a single-speed gearbox (torque-coupling) or a planetary gear set (speed-coupling). One of the main novelties of the present study concerns the definition of the instantaneous equivalent consumption (EC) function, which takes into account not only fuel consumption (FC) and the energy flow through the electric components, but also NO_x emissions, battery aging, and the battery SOC. The EC function has been trained using a cross-validation machine-learning technique, based on a genetic algorithm, where the training data set has been selected in order to maximize performances over a testing data set. The adoption of this technique, in conjunction with the new definition of EC, have led to the identification of very robust controllers, which provide an accurate control for different driving scenarios, even when the EC function is not specifically trained on the same missions over which it is tested. To this aim, a data set of fifty driving cycles and six user-defined missions, which cover a total distance of 70–100 km, has been considered as a training driving set. The ECMS controllers can be implemented in a vehicle control unit, and their performance has resulted to be close to that of a dynamic programming tool, which has here been used as benchmark

  2. Modern Solutions for Automation of Electrical Traction Power Supply Systems

    Directory of Open Access Journals (Sweden)

    Ana Mihaela Andreica

    2011-09-01

    Full Text Available This paper presents modern solutions for the automation of the electrical traction power supply system used in urban public transport (trams, trolleybuses and subway trains. The monitoring and control of this process uses SCADA distributed architectures, grouped around a central point (dispatcher who controls all field sensors, transmitters and actuators using programmable logical controllers. The presented applications refer to the Bucharest electrical transport infrastructure.

  3. Research of the multipolar induction traction frequency regulated motor

    Directory of Open Access Journals (Sweden)

    V. Ia. Bespalov

    2014-01-01

    Full Text Available The paper considers the application features of traction induction electric motors in transmissions of vehicles. It shows that one of important stages in their designing is to choose the number of poles. In traction electric drives engines with the raised number of poles without comprehensive assessment of such solution are often applied. The paper investigates dynamic and power characteristics of the multi-polar traction asynchronous engine (TAE designed and made for using in the individual electric drive of heavy-load wheeled cars. The basic functional elements of the model to simulate the electric drive in Matlab environment with the Simulink and SimPower Systems applications in the structure with vector control are described, and the simulation modeling results of its dynamic mechanical characteristics are provided. It is established that because of increased alternating frequency of currents of the multi-polar engine in the range of high speeds there is an excessive decrease in the torque and the requirement for constancy of the target capacity, corresponding to the specified traction characteristic is not fulfilled. It is a consequence of the waveform distortion of engine phase current in the range of high speeds because of incapability of the power source to compensate an increasing EMF of movement as the speed continues to grow.The paper studies the influence of increased current frequencies on the additional losses in the engine. The analysis of electromagnetic field penetration depth in the copper conductor of stator winding at high frequency allowed us to establish a significant skin – effect. The quantitative assessment is given to this phenomenon by results of numerical calculation of electromagnetic field distribution in a stator groove. Significant increase in additional losses in the engine is established, and estimates of flow loss extent because of damping actions of eddy currents in the laminated steel of stator at

  4. Systemic antibody response to nano-size calcium phospate biocompatible adjuvant adsorbed HEV-71 killed vaccine

    OpenAIRE

    Saeed, Mohamed Ibrahim; Omar, Abd Rahaman; Hussein, Mohd Zobir; Elkhidir, Isam Mohamed; Sekawi, Zamberi

    2015-01-01

    Purpose Since 1980s, human enterovirus-71 virus (HEV-71) is one of the common infectious disease in Asian Pacific region since late 1970s without effective commercial antiviral or protective vaccine is unavailable yet. The work examines the role of vaccine adjuvant particle size and the route of administration on postvaccination antibody response towards HEV-71 vaccine adsorbed to calcium phosphate (CaP) adjuvant. Materials and Methods First, CaP nano-particles were compared to a commercial m...

  5. Why is the market for hybrid electric vehicles (HEVs) moving slowly?

    Science.gov (United States)

    Rahmani, Djamel; Loureiro, Maria L

    2018-01-01

    Hybrid electric vehicles (HEVs) could be a good short term option to help achieve global targets regarding road transport greenhouse gas emissions. Several common and country-specific public policies based on price or tax rebates are established in order to encourage the adoption of HEVs. The present research empirically assesses market preferences for HEVs in Spain, looking at the role of subsidies. An interactive internet-based survey was conducted in a representative sample (N = 1,200) of Spanish drivers. Drivers are willing to pay an extra amount of €1,645 for a HEV model compared to a conventional vehicle, premium which is well below the price markup for these cars. Therefore, current levels of economic subsidies applied in isolation to promote these types of vehicles may have a quite limited effect in extending their use. Overall, it is found that drivers have clear misconceptions about HEVs, which affect their purchasing choices and perceptions. Therefore, a policy mix of various incentives (including informational campaigns) may be required in order to stimulate the demand for HEVs.

  6. Why is the market for hybrid electric vehicles (HEVs) moving slowly?

    Science.gov (United States)

    Rahmani, Djamel; Loureiro, Maria L.

    2018-01-01

    Hybrid electric vehicles (HEVs) could be a good short term option to help achieve global targets regarding road transport greenhouse gas emissions. Several common and country-specific public policies based on price or tax rebates are established in order to encourage the adoption of HEVs. The present research empirically assesses market preferences for HEVs in Spain, looking at the role of subsidies. An interactive internet-based survey was conducted in a representative sample (N = 1,200) of Spanish drivers. Drivers are willing to pay an extra amount of €1,645 for a HEV model compared to a conventional vehicle, premium which is well below the price markup for these cars. Therefore, current levels of economic subsidies applied in isolation to promote these types of vehicles may have a quite limited effect in extending their use. Overall, it is found that drivers have clear misconceptions about HEVs, which affect their purchasing choices and perceptions. Therefore, a policy mix of various incentives (including informational campaigns) may be required in order to stimulate the demand for HEVs. PMID:29561860

  7. Optimal energy management of HEVs with hybrid storage system

    International Nuclear Information System (INIS)

    Vinot, E.; Trigui, R.

    2013-01-01

    Highlights: • A battery and ultra-capacitor system for parallel hybrid vehicle is considered. • Optimal management using Pontryagin’s minimum principle is developed. • Battery stress limitation is taken into account by means of RMS current. • Rule based management approaching the optimal control is proposed. • Comparison between rule based and optimal management are proposed using Pareto front. - Abstract: Energy storage systems are a key point in the design and development of electric and hybrid vehicles. In order to reduce the battery size and its current stress, a hybrid storage system, where a battery is coupled with an electrical double-layer capacitor (EDLC) is considered in this paper. The energy management of such a configuration is not obvious and the optimal operation concerning the energy consumption and battery RMS current has to be identified. Most of the past work on the optimal energy management of HEVs only considered one additional power source. In this paper, the control of a hybrid vehicle with a hybrid storage system (HSS), where two additional power sources are used, is presented. Applying the Pontryagin’s minimum principle, an optimal energy management strategy is found and compared to a rule-based parameterized control strategy. Simulation results are shown and discussed. Applied on a small compact car, optimal and ruled-based methods show that gains of fuel consumption and/or a battery RMS current higher than 15% may be obtained. The paper also proves that a well tuned rule-based algorithm presents rather good performances when compared to the optimal strategy and remains relevant for different driving cycles. This rule-based algorithm may easily be implemented in a vehicle prototype or in an HIL test bench

  8. Traction-related problems after hip arthroscopy

    DEFF Research Database (Denmark)

    Frandsen, Lone; Lund, Bent; Grønbech Nielsen, Torsten

    2017-01-01

    . The questionnaire included questions on patients' perceptions of traction-related problems in the groin area, at the knee and ankle and how patients had coped with these problems. A total of 100 consecutive patients undergoing hip arthroscopy filled out the questionnaire. Primary findings of this study were that 74......% of patients reported some sort of traction-related problems after hip arthroscopy. About 32% of the patients had problems in the groin area and 49% of the patients complained of symptoms in the knee joint. A total of 37% of the patients had experienced problems from the traction boot in the ankle area....... The complications were found to be temporary and disappeared after 2-4 weeks. Five patients still had complaints after 3 months. All five patients had a pre-existing knee injury prior to undergoing hip arthroscopy. Traction-related problems after hip arthroscopy are a challenge and our study showed that 74...

  9. Traction-related problems after hip arthroscopy

    Science.gov (United States)

    Lund, Bent; Grønbech Nielsen, Torsten; Lind, Martin

    2017-01-01

    Abstract Traction-related problems are poorly described in the existing literature. The purpose of this prospective study was to describe traction-related problems and how patients perceive these problems. The study was a descriptive cohort study and data were collected from questionnaires and patient files. The questionnaire included questions on patients’ perceptions of traction-related problems in the groin area, at the knee and ankle and how patients had coped with these problems. A total of 100 consecutive patients undergoing hip arthroscopy filled out the questionnaire. Primary findings of this study were that 74% of patients reported some sort of traction-related problems after hip arthroscopy. About 32% of the patients had problems in the groin area and 49% of the patients complained of symptoms in the knee joint. A total of 37% of the patients had experienced problems from the traction boot in the ankle area. The complications were found to be temporary and disappeared after 2–4 weeks. Five patients still had complaints after 3 months. All five patients had a pre-existing knee injury prior to undergoing hip arthroscopy. Traction-related problems after hip arthroscopy are a challenge and our study showed that 74% of the patients reported traction-related problems. This is significantly higher than previously reported. The present study found a high rate of complaints from the knee and ankle joints that have not previously been reported. The presented data suggest the need for more pre-surgery patient information about possible traction-related problems. PMID:28630721

  10. Fast Thermal Runaway Detection for Lithium-Ion Cells in Large Scale Traction Batteries

    Directory of Open Access Journals (Sweden)

    Sascha Koch

    2018-03-01

    Full Text Available Thermal runaway of single cells within a large scale lithium-ion battery is a well-known risk that can lead to critical situations if no counter measures are taken in today’s lithium-ion traction batteries for battery electric vehicles (BEVs, plug-in hybrid electric vehicles (PHEV and hybrid electric vehicles (HEVs. The United Nations have published a draft global technical regulation on electric vehicle safety (GTR EVS describing a safety feature to warn passengers in case of a thermal runaway. Fast and reliable detection of faulty cells undergoing thermal runaway within the lithium-ion battery is therefore a key factor in battery designs for comprehensive passenger safety. A set of various possible sensors has been chosen based on the determined cell thermal runaway impact. These sensors have been tested in different sized battery setups and compared with respect to their ability of fast and reliable thermal runaway detection and their feasibility for traction batteries.

  11. 3D Viscoelastic Traction Force Microscopy

    Science.gov (United States)

    Toyjanova, Jennet; Hannen, Erin; Bar-Kochba, Eyal; Darling, Eric M.; Henann, David L.; Franck, Christian

    2014-01-01

    Native cell-material interactions occur on materials differing in their structural composition, chemistry, and physical compliance. While the last two decades have shown the importance of traction forces during cell-material interactions, they have been almost exclusively presented on purely elastic in-vitro materials. Yet, most bodily tissue materials exhibit some level of viscoelasticity, which could play an important role in how cells sense and transduce tractions. To expand the realm of cell traction measurements and to encompass all materials from elastic to viscoelastic, this paper presents a general, and comprehensive approach for quantifying 3D cell tractions in viscoelastic materials. This methodology includes the experimental characterization of the time-dependent material properties for any viscoelastic material with the subsequent mathematical implementation of the determined material model into a 3D traction force microscopy (3D TFM) framework. Utilizing this new 3D viscoelastic TFM (3D VTFM) approach, we quantify the influence of viscosity on the overall material traction calculations and quantify the error associated with omitting time-dependent material effects, as is the case for all other TFM formulations. We anticipate that the 3D VTFM technique will open up new avenues of cell-material investigations on even more physiologically relevant time-dependent materials including collagen and fibrin gels. PMID:25170569

  12. Exploring the Effect of Increased Energy Density on the Environmental Impacts of Traction Batteries: A Comparison of Energy Optimized Lithium-Ion and Lithium-Sulfur Batteries for Mobility Applications

    Directory of Open Access Journals (Sweden)

    Felipe Cerdas

    2018-01-01

    Full Text Available The quest towards increasing the energy density of traction battery technologies has led to the emergence and diversification of battery materials. The lithium sulfur battery (LSB is in this regard a promising material for batteries due to its specific energy. However, due to its low volumetric energy density, the LSB faces challenges in mobility applications such as electric vehicles but also other transportation modes. To understand the potential environmental implication of LSB batteries, a comparative Life Cycle Assessment (LCA was performed. For this study, electrodes for both an NMC111 with an anode graphite and a LSB battery cell with a lithium metal foil as anode were manufactured. Data from disassembly experiments performed on a real battery system for a mid-size passenger vehicle were used to build the required life cycle inventory. The energy consumption during the use phase was calculated using a simulative approach. A set of thirteen impact categories was evaluated and characterized with the ReCiPe methodology. The results of the LCA in this study allow identification of the main sources of environmental problems as well as possible strategies to improve the environmental impact of LSB batteries. In this regard, the high requirements of N-Methyl-2-pyrrolidone (NMP for the processing of the sulfur cathode and the thickness of the lithium foil were identified as the most important drivers. We make recommendations for necessary further research in order to broaden the understanding concerning the potential environmental implication of the implementation of LSB batteries for mobility applications.

  13. Production of Hev b5 as a fluorescent biotin-binding tripartite fusion protein in insect cells

    International Nuclear Information System (INIS)

    Nordlund, Henri R.; Laitinen, Olli H.; Uotila, Sanna T.H.; Kulmala, Minna; Kalkkinen, Nisse; Kulomaa, Markku S.

    2005-01-01

    The presented green fluorescent protein and streptavidin core-based tripartite fusion system provides a simple and efficient way for the production of proteins fused to it in insect cells. This fusion protein forms a unique tag, which serves as a multipurpose device enabling easy optimization of production, one-step purification via streptavidin-biotin interaction, and visualization of the fusion protein during downstream processing and in applications. In the present study, we demonstrate the successful production, purification, and detection of a natural rubber latex allergen Hev b5 with this system. We also describe the production of another NRL allergen with the system, Hev b1, which formed large aggregates and gave small yields in purification. The aggregates were detected at early steps by microscopical inspection of the infected insect cells producing this protein. Therefore, this fusion system can also be utilized as a fast indicator of the solubility of the expressed fusion proteins and may therefore be extremely useful in high-throughput expression approaches

  14. Production of Hev b5 as a fluorescent biotin-binding tripartite fusion protein in insect cells.

    Science.gov (United States)

    Nordlund, Henri R; Laitinen, Olli H; Uotila, Sanna T H; Kulmala, Minna; Kalkkinen, Nisse; Kulomaa, Markku S

    2005-10-14

    The presented green fluorescent protein and streptavidin core-based tripartite fusion system provides a simple and efficient way for the production of proteins fused to it in insect cells. This fusion protein forms a unique tag, which serves as a multipurpose device enabling easy optimization of production, one-step purification via streptavidin-biotin interaction, and visualization of the fusion protein during downstream processing and in applications. In the present study, we demonstrate the successful production, purification, and detection of a natural rubber latex allergen Hev b5 with this system. We also describe the production of another NRL allergen with the system, Hev b1, which formed large aggregates and gave small yields in purification. The aggregates were detected at early steps by microscopical inspection of the infected insect cells producing this protein. Therefore, this fusion system can also be utilized as a fast indicator of the solubility of the expressed fusion proteins and may therefore be extremely useful in high-throughput expression approaches.

  15. Rigid two-axis MEMS force plate for measuring cellular traction force

    International Nuclear Information System (INIS)

    Takahashi, Hidetoshi; Jung, Uijin G; Shimoyama, Isao; Kan, Tetsuo; Tsukagoshi, Takuya; Matsumoto, Kiyoshi

    2016-01-01

    Cellular traction force is one of the important factors for understanding cell behaviors, such as spreading, migration and differentiation. Cells are known to change their behavior according to the mechanical stiffness of the environment. However, the measurement of cell traction forces on a rigid environment has remained difficult. This paper reports a micro-electromechanical systems (MEMS) force plate that provides a cellular traction force measurement on a rigid substrate. Both the high force sensitivity and high stiffness of the substrate were obtained using piezoresistive sensing elements. The proposed force plate consists of a 70 µ m  ×  15 µ m  ×  5 µ m base as the substrate for cultivating a bovine aortic smooth muscle cell, and the supporting beams with piezoresistors on the sidewall and the surface were used to measure the forces in both the horizontal and vertical directions. The spring constant and force resolution of the fabricated force plate in the horizontal direction were 0.2 N m −1 and less than 0.05 µ N, respectively. The cell traction force was measured, and the traction force increased by approximately 1 µ N over 30 min. These results demonstrate that the proposed force plate is applicable as an effective traction force measurement. (paper)

  16. Asymmetry of activation of lateral abdominal muscles during the neurodevelopmental traction technique.

    Science.gov (United States)

    Gogola, Anna; Gnat, Rafał; Zaborowska, Małgorzata; Dziub, Dorota; Gwóźdź, Michalina

    2018-01-01

    The aim of the study was to evaluate the symmetry and pattern of activation of lateral abdominal muscles (LAM) in response to neurodevelopmental traction technique. Measurements of LAM thickness were performed in four experimental conditions: during traction with the force of 5% body weight (5% traction): 1) in neutral position, 2) in 20° posterior trunk inclination; during traction with the force of 15% body weight (15% traction): 3) in neutral position, 4) in 20° posterior trunk inclination. Thirty-seven healthy children participated in the study. Not applicable. To evaluate LAM activation level ultrasound technology was employed (two Mindray DP660 devices (Mindray, Shenzhen, China) with 75L38EA linear probes). An experiment with repeated measurements of the dependent variables was conducted. Side-to-side LAM activation asymmetry showed relatively high magnitude, however, significant difference was found only in case of the obliquus externus (OE) during stronger traction (P muscle differences were most pronounced between the OE and TrA (P muscles showing less intense activation. In statistical terms, the only signs of side-to-side asymmetry of LAM activation are visible in case of the OE, however, the magnitude of asymmetry is relatively high. The results allow to identify patterns of activation of LAM in children showing typical development that will serve as a reference in future studies in children with neurological disorder. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Road dust from pavement wear and traction sanding

    Energy Technology Data Exchange (ETDEWEB)

    Kupiainen, K.

    2007-07-01

    Vehicles affect the concentrations of ambient airborne particles through exhaust emissions, but particles are also formed in the mechanical processes in the tire-road interface, brakes, and engine. Particles deposited on or in the vicinity of the road may be re-entrained, or resuspended, into air through vehicle-induced turbulence and shearing stress of the tires. A commonly used term for these particles is 'road dust'. The processes affecting road dust emissions are complex and currently not well known. Road dust has been acknowledged as a dominant source of PM10 especially during spring in the sub-arctic urban areas, e.g. in Scandinavia, Finland, North America and Japan. The high proportion of road dust in sub-arctic regions of the world has been linked to the snowy winter conditions that make it necessary to use traction control methods. Traction control methods include dispersion of traction sand, melting of ice with brine solutions, and equipping the tires with either metal studs (studded winter tires), snow chains, or special tire design (friction tires). Several of these methods enhance the formation of mineral particles from pavement wear and/or from traction sand that accumulate in the road environment during winter. When snow and ice melt and surfaces dry out, traffic-induced turbulence makes some of the particles airborne. A general aim of this study was to study processes and factors underlying and affecting the formation and emissions of road dust from paved road surfaces. Special emphasis was placed on studying particle formation and sources during tire road interaction, especially when different applications of traction control, namely traction sanding and/or winter tires were in use. Respirable particles with aerodynamic diameter below 10 micrometers (PM10) have been the main concern, but other size ranges and particle size distributions were also studied. The following specific research questions were addressed: (i) How do traction

  18. Long-Life, Oil-Free Polymeric, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Multi-roller traction drives have several advantages relative to geared units for aerospace and commercial drive applications. Among these are zero backlash, low...

  19. The importance of vehicle costs, fuel prices, and fuel efficiency to HEV market success.

    Energy Technology Data Exchange (ETDEWEB)

    Santini, D. J.; Patterson, P. D.; Vyas, A. D.

    1999-12-08

    Toyota's introduction of a hybrid electric vehicle (HEV) named ''Prius'' in Japan and Honda's proposed introduction of an HEV in the United States have generated considerable interest in the long-term viability of such fuel-efficient vehicles. A performance and cost projection model developed entirely at Argonne National Laboratory (ANL) is used here to estimate costs. ANL staff developed fuel economy estimates by extending conventional vehicle (CV) modeling done primarily under the National Cooperative Highway Research Program. Together, these estimates are employed to analyze dollar costs vs. benefits of two of many possible HEV technologies. We project incremental costs and fuel savings for a Prius-type low-performance hybrid (14.3 seconds zero to 60 mph acceleration, 260 time) and a higher-performance ''mild'' hybrid vehicle, or MHV (11 seconds 260 time). Each HEV is compared to a U.S. Toyota Corolla with automatic transmission (11 seconds 260 time). The base incremental retail price range, projected a decade hence, is $3,200-$3,750, before considering battery replacement cost. Historical data are analyzed to evaluate the effect of fuel price on consumer preferences for vehicle fuel economy, performance, and size. The relationship between fuel price, the level of change in fuel price, and consumer attitude toward higher fuel efficiency is also evaluated. A recent survey on the value of higher fuel efficiency is presented and U.S. commercial viability of the hybrids is evaluated using discount rates of 2090 and 870. Our analysis, with our current HEV cost estimates and current fuel savings estimates, implies that the U.S. market for such HEVS would be quite limited.

  20. An overview of the development of lead/acid traction batteries for electric vehicles in India

    Science.gov (United States)

    Sivaramaiah, G.; Subramanian, V. R.

    Electric vehicles (EVs) made an entry into the Indian scene quite recently in the area of passenger transportation, milk floats and other similar applications. The industrial EV market, with various models of fork-lift trucks and platform trucks already in wide use all over India, is a better understood application of EV batteries. The lead/acid traction batteries available in India are not of high-energy density. The best available indigenous lead/acid traction battery has an energy density ( C/5 rate) of 30 W h kg -1 as against 39 W h kg -1 available abroad. This paper reviews the developmental efforts relating to lead/acid traction batteries for electric vehicle applications in India, such as prototype road vehicles, commercial vehicles, rail cars, and locomotives. Due to the need for environmental protection and recognition of exhaustible, finite supplies of petroleum fuel, the Indian government is presently taking active interest in EV projects.

  1. Molecular Investigation on the Presence of Hepatitis E Virus (HEV) in Wild Game in North-Western Italy.

    Science.gov (United States)

    Serracca, Laura; Battistini, Roberta; Rossini, Irene; Mignone, Walter; Peletto, Simone; Boin, Claudia; Pistone, Giancarlo; Ercolini, Riccardo; Ercolini, Carlo

    2015-09-01

    Meat products from HEV-infected reservoir animal species are capable of transmitting HEV to humans and represent a public health concern. Human HEV cases have been linked to the consumption of raw or undercooked pig liver sausages, pork, and game meats, such as wild boars and deer worldwide. Direct exposure to swine or wild game species might also represent a source of HEV transmission especially for veterinarians, hunters, or butchers. A limited amount of data is available on HEV prevalence in wild boars in Italy and no data are available for other wild game species intended for human consumption. In this study, the circulation of HEV in four different animal species hunted in north-western Italy was evaluated to gain insight into the infection levels and the genetic diversity of the virus in such animal populations. Liver samples of 372 wild boars, 30 roe deer, 47 European hares and 38 coypus were analyzed for HEV RNA by real-time RT-PCR; positive samples were then sequenced and submitted to phylogenetic analysis. HEV RNA was detected in the livers of 7/372 (1.9%) wild boars tested, while no sample was positive for roe deer, European hare, and coypu. Phylogenetic analysis showed that wild boar HEV sequences belonged to HEV subtypes 3e, 3c, and 3f. Our results indicate that HEV is circulating only in wild boar among the considered game species in north-western Italy and suggest a potential zoonotic risk related to handling and/or consumption of raw or undercooked meat and products made of the liver from this species.

  2. Traction alopecia: A neglected entity in 2017

    Directory of Open Access Journals (Sweden)

    Christiana Oyinlola Akingbola

    2017-01-01

    Full Text Available Traction alopecia was first described in 1904 but is still a cause of scarring hair loss in young women worldwide. It is unique in being initially a reversible then an irreversible (scarring form of alopecia. Linked to tightly-pulled hairstyles, it is seen across all races. The pattern of hair loss depends on the style creating it but most commonly affects the frontotemporal hairline. There are some new examination findings associated with traction alopecia, which are traction folliculitis, the fringe sign and hair casts (pseudonits on dermatoscopy. These may prove key in prompting early specialist referral. The mainstay of current treatment is cessation of the contributing hairstyles. Camouflage, anti-inflammatory or growth-stimulating topical preparations are second line treatments. In later stages of severe traction alopecia hair transplantation may be the only effective treatment. The evidence basis for medical intervention with topical agents is anecdotal at best. Furthermore, additional research is required to clarify the pathogenesis of this biphasic alopecia. Until then, prompt diagnosis and identification of causative hairstyles are focus of current dermatological practice.

  3. Prediction of traction forces of motile cells.

    Science.gov (United States)

    Roux, Clément; Duperray, Alain; Laurent, Valérie M; Michel, Richard; Peschetola, Valentina; Verdier, Claude; Étienne, Jocelyn

    2016-10-06

    When crawling on a flat substrate, living cells exert forces on it via adhesive contacts, enabling them to build up tension within their cytoskeleton and to change shape. The measurement of these forces has been made possible by traction force microscopy (TFM), a technique which has allowed us to obtain time-resolved traction force maps during cell migration. This cell 'footprint' is, however, not sufficient to understand the details of the mechanics of migration, that is how cytoskeletal elements (respectively, adhesion complexes) are put under tension and reinforce or deform (respectively, mature and/or unbind) as a result. In a recent paper, we have validated a rheological model of actomyosin linking tension, deformation and myosin activity. Here, we complement this model with tentative models of the mechanics of adhesion and explore how closely these models can predict the traction forces that we recover from experimental measurements during cell migration. The resulting mathematical problem is a PDE set on the experimentally observed domain, which we solve using a finite-element approach. The four parameters of the model can then be adjusted by comparison with experimental results on a single frame of an experiment, and then used to test the predictive power of the model for following frames and other experiments. It is found that the basic pattern of traction forces is robustly predicted by the model and fixed parameters as a function of current geometry only.

  4. Traction alopecia: the root of the problem

    Directory of Open Access Journals (Sweden)

    Billero V

    2018-04-01

    Full Text Available Victoria Billero, Mariya MitevaDepartment of Dermatology and Cutaneous Surgery, University of Miami School of Medicine, Miami, FL, USAAbstract: Traction alopecia (TA affects one-third of women of African descent who wear various forms of traumatic hairstyling for a prolonged period of time. The risk of TA is increased by the extent of pulling and duration of traction, as well as the use of chemical relaxation. The frequent use of tight buns or ponytails, the attachment of weaves or hair extensions, and tight braids (such as cornrows and dreadlocks are believed to be the highest risk hairstyles. TA can also occur in the setting of religious and occupational traumatic hairstyling. In its later stages, the disease may progress into an irreversible scarring alopecia if traumatic hairstyling continues without appropriate intervention. The most common clinical presentation includes marginal alopecia and non-marginal patchy alopecia. A clue to the clinical diagnosis is the preservation of the fringe sign as opposed to its loss in frontal fibrosing alopecia (FFA. Dermoscopy can be helpful in the diagnosis and can detect the ongoing traction by the presence of hair casts. Histopathology can distinguish TA from alopecia areata, FFA, and patchy central centrifugal cicatricial alopecia. Currently, there is no cure. Therefore, it is imperative that clinicians educate high-risk populations about TA and those practices that may convey the risk of hair loss. Keywords: hair loss, alopecia, dermoscopy, trichoscopy, traction alopecia, African-American 

  5. Traction for low-back pain with or without sciatica.

    NARCIS (Netherlands)

    Clarke, J.A.; van Tulder, M.W.; Blomberg, S.E.; de Vet, H.C.W.; van der Heijden, G.J.; Bronfort, G.; Bouter, L.M.

    2007-01-01

    Background: Traction is used to treat low-back pain (LBP), often with other treatments. Objectives: To determine traction's effectiveness, compared to reference treatments, placebo, sham traction or no treatment for LBP. Search strategy: We searched CENTRAL (The Cochrane Library 2006, issue 4),

  6. The Determination of the Asynchronous Traction Motor Characteristics of Locomotive

    Directory of Open Access Journals (Sweden)

    Pavel Grigorievich Kolpakhchyan

    2017-01-01

    Full Text Available The article deals with the problem of the locomotive asynchronous traction motor control with the AC diesel-electric transmission. The limitations of the torque of the traction motor when powered by the inverter are determined. The recommendations to improve the use of asynchronous traction motor of locomotives with the AC diesel-electric transmission are given.

  7. 21 CFR 882.5960 - Skull tongs for traction.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Skull tongs for traction. 882.5960 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Therapeutic Devices § 882.5960 Skull tongs for traction. (a) Identification. Skull tongs for traction is an instrument used to immobilize a patient with a...

  8. COMPARATIVE ANALYSIS OF CONVERTER STRUCTURES OF THE TRACTION DRIVE PROSPECTIVE MULTI-SYSTEM ELECTRIC LOCOMOTIVES WITH DC TRACTION MOTORS

    Directory of Open Access Journals (Sweden)

    A. M. Muha

    2009-03-01

    Full Text Available In the article the structured schemes of steady-state converter are offered for traction drive of promising multisystem electric locomotives with traction engines of direct current and their comparative analysis is conducted.

  9. Hepatitis E virus genotype three infection of human liver chimeric mice as a model for chronic HEV infection

    NARCIS (Netherlands)

    M.D.B. van de Garde (Martijn D.B.); S.D. Pas (Suzan); G. van der Net (Guido); R.A. de Man (Robert); A.D.M.E. Osterhaus (Albert); B.L. Haagmans (Bart); A. Boonstra (Andre); T. Vanwolleghem (Thomas)

    2016-01-01

    textabstractGenotype (gt) 3 hepatitis E virus (HEV) infections are emerging in Western countries. Immunosuppressed patients are at risk of chronic HEV infection and progressive liver damage, but no adequate model system currently mimics this disease course. Here we explore the possibilities of in

  10. Physical Basis for Interfacial Traction-Separation Models

    International Nuclear Information System (INIS)

    Neville R. Moody

    2002-01-01

    Many weapon components contain interfaces between dissimilar materials where cracks can initiate and cause failure. In recent years many researchers in the fracture community have adopted a cohesive zone model for simulating crack propagation (based upon traction-separation relations) Sandia is implementing this model in its ASCI codes. There is, however, one important obstacle to using a cohesive zone modeling approach. At the present time traction-separation relations are chosen in an ad hoc manner. The goal of the present work is to determine a physical basis for Traction-Separation (T-U) relations. This report presents results of a program aimed at determining the dependence of such relations on adhesive and bulk properties. The work focused on epoxy/solid interfaces, although the approach is applicable to a broad range of materials. Asymmetric double cantilevered beam and free surface film nanoindentation fracture toughness tests were used to generate a unique set of data spanning length scales, applied mode mixities, and yield (plastic) zone constraint. The crucial roles of crack tip plastic zone size and interfacial adhesion were defined by varying epoxy layer thickness and using coupling agents or special self-assembled monolayers in preparing the samples. The nature of the yield zone was probed in collaborative experiments run at the Advanced Photon Source. This work provides an understanding of the major phenomena governing polymer/solid interfacial fracture and identifies the essential features that must be incorporated in a T-U based cohesive zone failure model. We believe that models using physically based T-U relations provide a more accurate and widely applicable description of interface cracking than models using ad hoc relations. Furthermore, these T-U relations provide an essential tool for using models to tailor interface properties to meet design needs

  11. Traction forces exerted by epithelial cell sheets

    International Nuclear Information System (INIS)

    Saez, A; Anon, E; Ghibaudo, M; Di Meglio, J-M; Hersen, P; Ladoux, B; Du Roure, O; Silberzan, P; Buguin, A

    2010-01-01

    Whereas the adhesion and migration of individual cells have been well described in terms of physical forces, the mechanics of multicellular assemblies is still poorly understood. Here, we study the behavior of epithelial cells cultured on microfabricated substrates designed to measure cell-to-substrate interactions. These substrates are covered by a dense array of flexible micropillars whose deflection enables us to measure traction forces. They are obtained by lithography and soft replica molding. The pillar deflection is measured by video microscopy and images are analyzed with home-made multiple particle tracking software. First, we have characterized the temporal and spatial distributions of traction forces of cellular assemblies of various sizes. The mechanical force balance within epithelial cell sheets shows that the forces exerted by neighboring cells strongly depend on their relative position in the monolayer: the largest deformations are always localized at the edge of the islands of cells in the active areas of cell protrusions. The average traction stress rapidly decreases from its maximum value at the edge but remains much larger than the inherent noise due to the force resolution of our pillar tracking software, indicating an important mechanical activity inside epithelial cell islands. Moreover, these traction forces vary linearly with the rigidity of the substrate over about two decades, suggesting that cells exert a given amount of deformation rather than a force. Finally, we engineer micropatterned substrates supporting pillars with anisotropic stiffness. On such substrates cellular growth is aligned with respect to the stiffest direction in correlation with the magnitude of the applied traction forces.

  12. Energetic macroscopic representation and inversion-based control of a CVT-based HEV

    NARCIS (Netherlands)

    Chouhou, M.; Grée, F.; Jivan, C.; Bouscayrol, A.; Hofman, T.

    2014-01-01

    A Continuous Variable Transmission (CVT) is introduced in the simulation model of a Hybrid Electric Vehicle (HEV). The CVT-based vehicle simulation and its control are deduced from the Energetic Macroscopic Representation (EMR). Simulations are provided to show the interest of the CVT in term of

  13. Energetic macroscopic representation and inversion- based control of a CVT-based HEV

    NARCIS (Netherlands)

    Chouhou, M.; Grée, F.; Jivan, C.; Bouscayrol, A.; Hofman, T.

    2013-01-01

    A Continuous Variable Transmission (CVT) is introduced in the simulation model of a Hybrid Electric Vehicle (HEV). The CVT-based vehicle simulation and its control are deduced from the Energetic Macroscopic Representation (EMR). Simulations are provided to show the interest of the CVT in term of

  14. Modeling and Control of Flexible HEV Charging Station upgraded with Flywheel Energy Storage

    DEFF Research Database (Denmark)

    Dragicevic, Tomislav; Shafiee, Qobad; Wu, Dan

    2014-01-01

    This paper deals with the design of a fast DC charging station (FCS) for hybrid electric vehicles (HEVs) that is connected at a remote location. Power rating of this new technology can go up to a hundred kW and it represents a main challenge for its broad acceptance in distribution systems...

  15. Simulation and Comparison of HEV Battery Control for Best Fuel Economy and Longer Battery Life

    OpenAIRE

    Adel, Boukehili; Youtong, Zhang; shuai, Sun

    2010-01-01

    Almost all HEV battery control strategies keep the battery state of charge (SOC) within a lower limit (SOCmin) (these strategies also called charge sustaining strategies). The goal from sustaining the SOC in this way is to prolong the battery life. But the question is

  16. Lipid transfer protein from Hevea brasiliensis (Hev b 12), a cross-reactive latex protein

    NARCIS (Netherlands)

    Beezhold, Donald H.; Hickey, Vicky L.; Kostyal, David A.; Puhl, Henry; Zuidmeer, Laurian; van Ree, Ronald; Sussman, Gordon L.

    2003-01-01

    BACKGROUND: Latex-allergic individuals experience clinical cross-reactivity to a large number of fruits and vegetables. Much of the cross-reactivity can be attributed to Hev b 6, but evidence indicates that additional cross-reactive allergens may be present. A common pan-allergen, which has not

  17. Gümnaasiumiõpilased õpetajate tööst HEV lastega / Ants Reinmaa

    Index Scriptorium Estoniae

    Reinmaa, Ants

    2001-01-01

    Lühikokkuvõte rakendusuuringust, millega selgitati põhi- ja keskkoolide ning gümnaasiumide õpilaste arvamusi ja hoiakuid õpetajate ja õpetajatöö suhtes. Uurimuse ühe osa moodustas keskendumine probleemidele, millistena paistavad gümnaasiumiõpilastele õpetajate tegevus HEV lastega

  18. Prevalence of Hepatitis A virus (HAV) and Hepatitis E virus (HEV) in the patients presenting with acute viral hepatitis.

    Science.gov (United States)

    Joon, A; Rao, P; Shenoy, S M; Baliga, S

    2015-02-01

    Hepatitis A virus (HAV) and Hepatitis E virus (HEV) are both enterically transmitted, resulting in acute viral hepatitis (AVH) in developing countries. They pose major health problems in our country. This study was done to determine prevalence of HAV and HEV in patients presenting with AVH and the co-infection of HAV and HEV in these patients. A cross-sectional study of 2-years duration was conducted in the Department of Microbiology, KMC, Mangalore. A non-random sampling of 958 patients presenting with AVH was considered in the study. On the basis of history, serum samples were analysed for IgM anti-HAV and IgM anti-HEV for the detection of HAV and HEV, respectively using commercially available ELISA kits. Data collected was analysed by using Statistical Package for the Social Sciences (SPSS) version 11.5. The seroprevalence of HAV- and HEV-positive patients were 19.31% and 10.54%, respectively. The seroprevalence of both HAV and HEV in patients with acute viral hepatitis was 11.5%. The prevalence of HAV and HEV among males (68% and 31%) was higher than in females (31% and 20%) and was predominantly seen among young adults. These infections were predominantly seen during end of monsoons and beginning of winter. Though the prevalence of HAV is much higher than that of HEV, co-infection rate of 11.5% mandates the screening for HEV which will be of immense importance in pregnant women and improving levels of personal hygiene among higher socio-economic population. These data will be essential for planning of future vaccination strategies and for better sanitation programme in this part of the country.

  19. FreedomCAR Advanced Traction Drive Motor Development Phase I

    Energy Technology Data Exchange (ETDEWEB)

    Ley, Josh (UQM Technologies, Inc.); Lutz, Jon (UQM Technologies, Inc.)

    2006-09-01

    The overall objective of this program is to design and develop an advanced traction motor that will meet the FreedomCAR and Vehicle Technologies (FCVT) 2010 goals and the traction motor technical targets. The motor specifications are given in Section 1.3. Other goals of the program include providing a cost study to ensure the motor can be developed within the cost targets needed for the automotive industry. The program has focused on using materials that are both high performance and low costs such that the performance can be met and cost targets are achieved. In addition, the motor technologies and machine design features must be compatible with high volume manufacturing and able to provide high reliability, efficiency, and ruggedness while simultaneously reducing weight and volume. Weight and volume reduction will become a major factor in reducing cost, material cost being the most significant part of manufacturing cost at high volume. Many motor technology categories have been considered in the past and present for traction drive applications, including: brushed direct current (DC), PM (PM) brushless dc (BLDC), alternating current (AC) induction, switched reluctance and synchronous reluctance machines. Of these machine technologies, PM BLDC has consistently demonstrated an advantage in terms of power density and efficiency. As rare earth magnet cost has declined, total cost may also be reduced over the other technologies. Of the many different configurations of PM BLDC machines, those which incorporate power production utilizing both magnetic torque as well as reluctance torque appear to have the most promise for traction applications. There are many different PM BLDC machine configurations which employ both of these torque producing mechanisms; however, most would fall into one of two categories--some use weaker magnets and rely more heavily on reluctance torque (reluctance-dominant PM machines), others use strong PMs and supplement with reluctance torque

  20. Solid-state transformer-based new traction drive system and control

    Science.gov (United States)

    Feng, Jianghua; Shang, Jing; Zhang, Zhixue; Liu, Huadong; Huang, Zihao

    2017-11-01

    A new type of traction drive system consisting of solid-state traction transformer (SSTT), inverter unit, auxiliary inverter, traction motor and other key components is built in order to suit the demand of developing the next-generation electric traction system which will be efficient and lightweight, with high power density. For the purpose of reducing system volume and weight and improving efficiency and grid-side power quality, an efficient SSTT optimized topology combining high-voltage cascaded rectifiers with high-power high-frequency LLC resonant converter is proposed. On this basis, an integrated control strategy built upon synchronous rotating reference frame is presented to achieve unified control over fundamental active, reactive and harmonic components. The carrier-interleaving phase shift modulation strategy is proposed to improve the harmonic performance of cascaded rectifiers. In view of the secondary pulsating existing in a single-phase system, the mathematical model of secondary power transfer is built, and the mechanism of pulsating voltage resulting in beat frequency of LLC resonant converter is revealed, so as to design optimum matching of system parameters. Simulation and experimental results have verified that the traction system and control scheme mentioned in this paper are reasonable and superior and that they meet the future application requirements for rail transit.

  1. Experimental investigation on the feasibility of heat pipe cooling for HEV/EV lithium-ion battery

    International Nuclear Information System (INIS)

    Tran, Thanh-Ha; Harmand, Souad; Desmet, Bernard; Filangi, Sebastien

    2014-01-01

    In this paper, the use of flat heat pipe as an effective and low-energy device to mitigate the temperature of a battery module designed for a HEV application was investigated. For this purpose, nominal heat flux generated by a battery module was reproduced and applied to a flat heat pipe cooling system. The thermal performance of the flat heat pipe cooling system was compared with that of a conventional heat sink under various cooling conditions and under several inclined positions. The results show that adding heat pipe reduced the thermal resistance of a common heat sink of 30% under natural convection and 20% under low air velocity cooling. Consequently, the cell temperature was kept below 50 °C, which cannot be achieved using heat sink. According to the space allocated for the battery pack in the vehicle, flat heat pipe can be used in vertical or horizontal position. Furthermore, flat heat pipe works efficiently under different grade road conditions. The transient behaviour of the flat heat pipe was also studied under high frequency and large amplitude variable input power. The flat heat pipe was found to handle more efficiently instant increases of the heat flux than the conventional heat sink. -- Highlights: • Constant heat flux was applied to a flat heat pipe cooling system. • Its thermal performance was compared with that of a heat sink under several cooling conditions. • The influence of the inclination was evaluated. • The heat pipe transient behaviour was also studied under variable input power. • Heat pipe was found to be an effective and low-energy solution for HEV/EV battery cooling

  2. Observer Based Traction/Braking Control Design for High Speed Trains Considering Adhesion Nonlinearity

    Directory of Open Access Journals (Sweden)

    Wenchuan Cai

    2014-01-01

    Full Text Available Train traction/braking control, one of the key enabling technologies for automatic train operation, literally takes its action through adhesion force. However, adhesion coefficient of high speed train (HST is uncertain in general because it varies with wheel-rail surface condition and running speed; thus, it is extremely difficult to be measured, which makes traction/braking control design and implementation of HSTs greatly challenging. In this work, force observers are applied to estimate the adhesion force or/and the resistance, based on which simple traction/braking control schemes are established under the consideration of actual wheel-rail adhesion condition. It is shown that the proposed controllers have simple structure and can be easily implemented from real applications. Numerical simulation also validates the effectiveness of the proposed control scheme.

  3. Tracking Traction Force Changes of Single Cells on the Liquid Crystal Surface

    Directory of Open Access Journals (Sweden)

    Chin Fhong Soon

    2015-01-01

    Full Text Available Cell migration is a key contributor to wound repair. This study presents findings indicating that the liquid crystal based cell traction force transducer (LCTFT system can be used in conjunction with a bespoke cell traction force mapping (CTFM software to monitor cell/surface traction forces from quiescent state in real time. In this study, time-lapse photo microscopy allowed cell induced deformations in liquid crystal coated substrates to be monitored and analyzed. The results indicated that the system could be used to monitor the generation of cell/surface forces in an initially quiescent cell, as it migrated over the culture substrate, via multiple points of contact between the cell and the surface. Future application of this system is the real-time assaying of the pharmacological effects of cytokines on the mechanics of cell migration.

  4. Swine and rabbits are the main reservoirs of hepatitis E virus in China: detection of HEV RNA in feces of farmed and wild animals.

    Science.gov (United States)

    Xia, Junke; Zeng, Hang; Liu, Lin; Zhang, Yulin; Liu, Peng; Geng, Jiabao; Wang, Lin; Wang, Ling; Zhuang, Hui

    2015-11-01

    Hepatitis E virus (HEV) infection is recognized as a zoonosis. The prevalence of HEV RNA and anti-HEV antibodies in many animal species has been reported, but the host range of HEV is unclear. The aims of this study were to investigate HEV infection in various animal species and to determine the reservoirs of HEV. Eight hundred twenty-two fecal samples from 17 mammal species and 67 fecal samples from 24 avian species were collected in China and tested for HEV RNA by RT-nPCR. The products of PCR were sequenced and analyzed phylogenetically. The positive rates of HEV RNA isolated from pigs in Beijing, Shandong, and Henan were 33%, 30%, and 92%, respectively, and that from rabbits in Beijing was 5%. HEV RNA was not detectable in farmed foxes, sheep or sika deer, or in wild animals in zoos, including wild boars, yaks, camels, Asiatic black bears, African lions, red pandas, civets, wolves, jackals and primates. Sequence analysis revealed that swine isolates had 97.8%-98.4% nucleotide sequence identity to genotype 4d isolates from patients in Shandong and Jiangsu of China. Phylogenetic analysis showed that swine HEV isolates belong to genotype 4, including subgenotype 4h in Henan and 4d in Beijing and Shandong. The rabbit HEV strains shared 93%-99% nucleotide sequence identity with rabbit strains isolated from Inner Mongolia. In conclusion, swine and rabbits have been confirmed to be the main reservoirs of HEV in China.

  5. Orthodontic Traction of Impacted Canine Using Cantilever

    OpenAIRE

    Nakandakari, Cláudia; Gonçalves, João Roberto; Cassano, Daniel Serra; Raveli, Taísa Boamorte; Bianchi, Jonas; Raveli, Dirceu Barnabé

    2016-01-01

    The impaction of the maxillary canines causes relevant aesthetic and functional problems. The multidisciplinary approach to the proper planning and execution of orthodontic traction of the element in question is essential. Many strategies are cited in the literature; among them is the good biomechanical control in order to avoid possible side effects. The aim of this paper is to present a case report in which a superior canine impacted by palatine was pulled out with the aid of the cantilever...

  6. Digital Model of Railway Electric Traction Lines

    Science.gov (United States)

    Garg, Rachana; Mahajan, Priya; Kumar, Parmod

    2017-08-01

    The characteristic impedance and propagation constant define the behavior of signal propagation over the transmission lines. The digital model for railway traction lines which includes railway tracks is developed, using curve fitting technique in MATLAB. The sensitivity of this model has been computed with respect to frequency. The digital sensitivity values are compared with the values of analog sensitivity. The developed model is useful for digital protection, integrated operation, control and planning of the system.

  7. Understanding the traction of tennis surfaces

    OpenAIRE

    Clarke, James; Carré, Matt; Richardson, Andrea; Yang, Zhijun; Damm, Loic; Dixon, Sharon

    2011-01-01

    The traction provided by a footwear-surface interaction can have an impact on player safety, performance and overall enjoyment of sport. Mechanical test methods used for the testing and categorisation of safe playing surfaces do not tend to simulate loads occurring during participation on the surface, and thus are unlikely to predict human response to the surface. For example, the pendulum system routinely employed by the International Tennis Federation (I.T.F.) utilises a standard rubber ‘fo...

  8. Preliminary study on the detection of hepatitis E virus (HEV antibodies in pigs and wild boars in Poland

    Directory of Open Access Journals (Sweden)

    Weiner Marcin

    2016-12-01

    Full Text Available Introduction: Although HEV infection in pigs does not pose a major economic risk to pork production, the risk of zoonotic transmission to humans is an important aspect of public health. HEV genotype 3 infections were reported in developed countries in individuals who had consumed raw meat or meat products from deer, wild boars, or pigs. The aim of the study was the analysis of the occurrence of HEV-specific antibodies among wild boars and domestic pigs in Poland. Material and Methods: A total of 290 samples from wild boars and 143 samples from pigs were tested. The antibodies were tested by ELISA. Results: The presence of anti-HEV IgG was demonstrated in 44.1% of pigs and 31.0% of wild boars. Anti-HEV IgG antibodies were detected in 1.4% of samples from pigs and in 2.1% of samples from wild boars at borderline level. The statistical analysis shows significant differences in the positive results for anti-HEV IgG between the groups of pigs and wild boars (P = 0.0263. Conclusion: Regular surveillance of the occurrence of HEV in swine and wild boars should be performed in the future.

  9. Orthodontic Traction of Impacted Canine Using Cantilever

    Directory of Open Access Journals (Sweden)

    Cláudia Nakandakari

    2016-01-01

    Full Text Available The impaction of the maxillary canines causes relevant aesthetic and functional problems. The multidisciplinary approach to the proper planning and execution of orthodontic traction of the element in question is essential. Many strategies are cited in the literature; among them is the good biomechanical control in order to avoid possible side effects. The aim of this paper is to present a case report in which a superior canine impacted by palatine was pulled out with the aid of the cantilever on the Segmented Arch Technique (SAT concept. A 14.7-year-old female patient appeared at clinic complaining about the absence of the upper right permanent canine. The proposed treatment prioritized the traction of the upper right canine without changing the occlusion and aesthetics. For this, it only installed the upper fixed appliance (Roth with slot 0.018, opting for SAT in order to minimize unwanted side effects. The use of cantilever to the traction of the upper right canine has enabled an efficient and predictable outcome, because it is of statically determined mechanics.

  10. Traction alopecia: the root of the problem.

    Science.gov (United States)

    Billero, Victoria; Miteva, Mariya

    2018-01-01

    Traction alopecia (TA) affects one-third of women of African descent who wear various forms of traumatic hairstyling for a prolonged period of time. The risk of TA is increased by the extent of pulling and duration of traction, as well as the use of chemical relaxation. The frequent use of tight buns or ponytails, the attachment of weaves or hair extensions, and tight braids (such as cornrows and dreadlocks) are believed to be the highest risk hairstyles. TA can also occur in the setting of religious and occupational traumatic hairstyling. In its later stages, the disease may progress into an irreversible scarring alopecia if traumatic hairstyling continues without appropriate intervention. The most common clinical presentation includes marginal alopecia and non-marginal patchy alopecia. A clue to the clinical diagnosis is the preservation of the fringe sign as opposed to its loss in frontal fibrosing alopecia (FFA). Dermoscopy can be helpful in the diagnosis and can detect the ongoing traction by the presence of hair casts. Histopathology can distinguish TA from alopecia areata, FFA, and patchy central centrifugal cicatricial alopecia. Currently, there is no cure. Therefore, it is imperative that clinicians educate high-risk populations about TA and those practices that may convey the risk of hair loss.

  11. Current status of environmental, health, and safety issues of electrochemical capacitors for advanced vehicle applications

    Energy Technology Data Exchange (ETDEWEB)

    Vimmerstedt, L J; Hammel, C J

    1997-04-01

    Electrochemical capacitors are a candidate for traction power assists in hybrid electric vehicles (HEVs). Other advanced automotive applications, while not the primary focus of current development efforts, are also possible. These include load leveling high-energy batteries, power conditioning electronics, electrically hated catalysts, electric power steering, and engine starter power. Higher power and longer cycle life are expected for electrochemical capacitors than for batteries. Evaluation of environmental, health, and safety (EH and S) issues of electrochemical capacitors is an essential part of the development and commercialization of electrochemical capacitors for advanced vehicles. This report provides an initial EH and S assessment. This report presents electrochemical capacitor electrochemistry, materials selection, intrinsic material hazards, mitigation of those hazards, environmental requirements, pollution control options, and shipping requirements. Most of the information available for this assessment pertains to commercial devices intended for application outside the advanced vehicle market and to experiment or prototype devices. Electrochemical capacitors for power assists in HEVs are not produced commercially now. Therefore, materials for advanced vehicle electrochemical capacitors may change, and so would the corresponding EH and S issues. Although changes are possible, this report describes issues for likely electrochemical capacitor designs.

  12. Home Cervical Traction to Reduce Neck Pain in Fighter Pilots.

    Science.gov (United States)

    Chumbley, Eric M; O'Hair, Nicole; Stolfi, Adrienne; Lienesch, Christopher; McEachen, James C; Wright, Bruce A

    2016-12-01

    Most fighter pilots report cervical pain during their careers. Recommendations for remediation lack evidence. We sought to determine whether regular use of a home cervical traction device could decrease reported cervical pain in F-15C pilots. An institutional review board-approved, Health Insurance Portability and Accountability Act-compliant, controlled crossover study was undertaken with 21 male F-15C fighter pilots between February and June 2015. Of the 21 subjects, 12 completed 6 wk each of traction and control, while logging morning, postflying, and post-traction pain. Pain was compared with paired t-tests between the periods, from initial pain scores to postflying, and postflying to post-traction. In the traction phase, initial pain levels increased postflight, from 1.2 (0.7) to 1.6 (1.0) Subsequent post-traction pain levels decreased to 1.3 (0.9), with a corresponding linear decrease in pain relative to pain reported postflight. The difference in pain levels after traction compared to initial levels was not significant, indicating that cervical traction was effective in alleviating flying-related pain. Control pain increased postflight from 1.4 (0.9) to 1.9 (1.3). Daily traction phase pain was lower than the control, but insignificant. To our knowledge, this is the first study of home cervical traction to address fighter pilots' cervical pain. We found a small but meaningful improvement in daily pain rating when using cervical traction after flying. These results help inform countermeasure development for pilots flying high-performance aircraft. Further study should clarify the optimal traction dose and timing in relation to flying.Chumbley EM, O'Hair N, Stolfi A, Lienesch C, McEachen JC, Wright BA. Home cervical traction to reduce neck pain in fighter pilots. Aerosp Med Hum Perform. 2016; 87(12):1010-1015.

  13. Determination of the full-genome sequence of hepatitis E virus (HEV) SAAS-FX17 and use as a reference to identify putative HEV genotype 4 virulence determinants.

    Science.gov (United States)

    Zhu, Yumin; Yu, Xiaoming; Huang, Fenfen; Yu, Ruisong; Dong, Shijuan; Si, Fusheng; Zhang, Yuanshu; Li, Zhen

    2012-11-08

    Four major genotypes of hepatitis E virus (HEV), the causative agent of hepatitis E, have so far been recognized. While genotypes 3 and 4 are both zoonotic, the disease symptoms caused by the latter tend to be more severe. To examine if specific nucleotide/amino acid variations between genotypes 3 and 4 play a role in determining the severity of hepatitis E disease, the complete genome of one swine HEV genotype 4 isolate, SAAS-FX17, was determined and compared with other genotype 4 and genotype 3 genomes to identify putative HEV genotype 4 virulence determinants. A total of 42 conformable nt/aa variations between genotype 3 and 4 HEVs were detected, of which 19 were proposed to be potential disease severity determinants for genotype 4 strains. One potential determinant was located in each of the 5'-UTR and 3'-UTR, 3 and 12 within ORF1 and ORF2 respectively, and 2 in the junction region.

  14. Efficient start–up energy management via nonlinear control for eco–traction systems

    International Nuclear Information System (INIS)

    Becherif, M.; Ramadan, H.S.; Ayad, M.Y.; Hissel, D.; Desideri, U.; Antonelli, M.

    2017-01-01

    Highlights: • Renewable HPS for the train start-up within feeding durations. • Dynamic modelling of the modern HPS applied to traction systems. • Port-Controlled Hamiltonian (PCH) design for supercapacitors’ charge/discharge operation. • Experimental validation and applicability of HPSs for energy management in eco-tractions. - Abstract: Electrochemical capacitors, called supercapacitors (SCs) or ultracapacitors, are devices conveniently used for embedded electrical energy management owing to their huge capacitance, low internal resistance and flexible control through power electronic conversion. This paper proposes a main power supply of hybrid Wind Generator (WG)–SC within the train station for feeding the traction onboard SC through specified limited feeding transit durations. Onboard SCs provide the train with the requested start–up self–energy. The hybrid WG–SCs system is an environmental–friendly source that enables the independency on national grid and guarantees an efficient bidirectional power transfer for energy management with enhanced dynamic performance. Therefore, the dynamic modelling and the experimental analysis of the modern hybrid WG–SCs used for managing the charge/discharge operation of SCs at Unity Power Factor (UPF) mode are presented. For this purpose, the Port–Controlled Hamiltonian (PCH) methodology is deduced and explicitly presented. Simulation results, via MATLAB™, reveal that the proposed PCH control methodology can be successfully implemented to ensure acceptable system dynamic behavior. Numerical results are validated with experimental measurements to investigate the significance of the PCH approach for the energy management operation in eco-tractions.

  15. ANALYSIS OF ENERGY EFFICIENCY OF OPERATING MODES OF ELECTRICAL SYSTEMS WITH THE TRACTION LOADS

    Directory of Open Access Journals (Sweden)

    V. E. Bondarenko

    2017-03-01

    Full Text Available Innovative scenarios of reliable energy supply of transportation process aimed at reducing the specific energy consumption and increase energy efficiency of the systems of electric traction. The paper suggests innovative energy saving directions in traction networks of railways and new circuit solutions accessing traction substations in energy systems networks, ensure energy security of the transportation process. To ensure the energy security of rail transport special schemes were developed to propose the concept of external power traction substations, which would increase the number of connections to the networks of 220 – 330 kV, as well as the creation of transport and energy corridors, development of its own supply of electric networks of 110 kV substations and mobile RP-110 kV of next generation. Therefore, the investment program of the structures owned by the Ukrainian Railways (Ukrzaliznytsia need to be synchronized in their technological characteristics, as well as the criteria of reliability and quality of power supply with the same external energy investment programs. It is found that without any load on left or right supplying arm one of two less loaded phases of traction transformer begins generating specific modes in the supplying three-phase line. Thus, modes of mobile substation cause leakage in one of the phases of the supply line of traction transformers of active-capacitive current, and as a result generating energy in the main power line of 154 kV, which is fixed and calculated by electricity meters. For these three phase mode supply network is necessary to use 1st algorithm, i.e. taking into account the amount of electricity as the energy in all phases. For effective application of reactive power compensation devices in the AC traction power supply systems it is proposed to develop regulatory documentation on necessity of application and the order of choice of parameters and placement of compensation systems taking into

  16. Skeletal traction and intramedullary nailing cost-effectiveness

    African Journals Online (AJOL)

    In the operative group 24 patients had union with one delayed union while in the traction group 12 patients had union, 9 with mal union and 4 delayed union. Conclusion: Intramedullary nailing is more cost-effective than skeletal traction. It met the dominant strategy, because it was significantly less costly than skeletal ...

  17. Traction for low-back pain with or without sciatica

    NARCIS (Netherlands)

    Wegner, I.; Widyahehening, I.S.; van Tulder, M.W.; Blomberg, S.E.I.; de Vet, H.C.W.; Brønfort, G.; Bouter, L.M.; van der Heijden, G.J.

    2013-01-01

    Background Traction has been used to treat low-back pain (LBP), often in combination with other treatments. We included both manual and machine-delivered traction in this review. This is an update of a Cochrane review first published in 1995, and previously updated in 2006. Objectives To assess the

  18. Orthodontic traction of impacted canine using magnet: a case report

    OpenAIRE

    Li, Larry CF; Wong, Ricky WK; King, Nigel M

    2008-01-01

    ABSTRACT: A 15 year and 1 month old Chinese female with palatally impacted upper left canine was successfully treated with an upper removable appliance with a magnet incorporated to provide orthodontic traction force. This case report indicates the possibility of using magnetic force as a safe, effective and comfortable way for orthodontic traction.

  19. Development of Traction Drive Motors for the Toyota Hybrid System

    Science.gov (United States)

    Kamiya, Munehiro

    Toyota Motor Corporation developed in 2005 a new hybrid system for a large SUV. This system included the new development of a high-speed traction drive motor achieving a significant increase in power weight ratio. This paper provides an overview of the hybrid system, discusses the characteristics required of a traction drive motor, and presents the technologies employed in the developed motor.

  20. Cost effectiveness of using surgery versus skeletal traction in ...

    African Journals Online (AJOL)

    The financial cost benefit of surgery was further complimented by better functional outcomes. Conclusion: The data indicates a cost advantage of managing femoral shaft fracture by surgery compared to traction. Furthermore the longer hospital stay in the traction group is associated with more malunion, limb deformity and ...

  1. THE TRACTION ELECTRIC OPERATION AND ITS EXPLOITATION ABILITIES

    Directory of Open Access Journals (Sweden)

    V. M. Bezruchenko

    2011-04-01

    Full Text Available The possibilities of asynchronous traction electric motor drive are considered at the certain coupling mass taking into account the coupling restrictions. A variant of using the regulation law for electric motor drive allowing realizing traction force more rationally is offered. The possibility of reaching the speeds to 220 km/h for electric locomotive DS3 is shown

  2. Electric vehicle regenerative antiskid braking and traction control system

    Science.gov (United States)

    Cikanek, Susan R.

    1995-01-01

    An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydrualic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control.

  3. Electric vehicle regenerative antiskid braking and traction control system

    Science.gov (United States)

    Cikanek, S.R.

    1995-09-12

    An antiskid braking and traction control system for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes one or more sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensors and determining if regenerative antiskid braking control, requiring hydraulic braking control, or requiring traction control are required. The processor then employs a control strategy based on the determined vehicle state and provides command signals to a motor controller to control the operation of the electric traction motor and to a brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative antiskid braking control, hydraulic braking control, and traction control. 10 figs.

  4. Comparison between effectiveness of Mechanical and Manual Traction combined with mobilization and exercise therapy in Patients with Cervical Radiculopathy.

    Science.gov (United States)

    Bukhari, Syed Rehan Iftikhar; Shakil-Ur-Rehman, Syed; Ahmad, Shakeel; Naeem, Aamer

    2016-01-01

    Cervical radiculopathy is a common neuro-musculo-skeletal disorder causing pain and disability. Traction is part of the evidence based manual physical therapy management due to its mechanical nature, type of traction and parameters related to its applicability and are still to be explored more through research. Our objective was to determine the Effects of Mechanical versus Manual Traction in Manual Physical Therapy combined with segmental mobilization and exercise therapy in the physical therapy management of Patients with Cervical Radiculopathy. This randomized control trial was conducted at department of physical therapy and rehabilitation, Rathore Hospital Faisalabad, from February to July 2015. Inclusion criteria were both male and female patients with evident symptoms of cervical spine radiculopathy and age ranged between 20-70 years. The exclusion criteria were Patients with history of trauma, neck pain without radiculopathy, aged less than 20 and more than 70. A total of 72 patients with cervical radiculopathy were screened out as per the inclusion criteria, 42 patients were randomly selected and placed into two groups by toss and trial method, and only 36 patients completed the study, while 6 dropped out. The mechanical traction was applied in group A and manual traction in group B along with common intervention of segmental mobilization and exercise therapy in both groups for 6 weeks. The patient's outcomes were assessed by self reported NPRS and NDI at the baseline and after completion of 06 weeks exercise program at 3 days per week. The data was analyzed through SPSS version-21, and paired T test was applied at 95% level significance to determine the statistical deference between two groups. Clinically the group of patients treated with mechanical traction managed pain (mean pre 6.26, mean post 1.43), and disability (mean pre 24.43 and mean post 7.26) more effectively as compared with the group of patients treated with manual traction (Pain mean pre 6

  5. Development of nickel/metal-hydride batteries for EVs and HEVs

    Science.gov (United States)

    Taniguchi, Akihiro; Fujioka, Noriyuki; Ikoma, Munehisa; Ohta, Akira

    This paper is to introduce the nickel/metal-hydride (Ni/MH) batteries for electric vehicles (EVs) and hybrid electric vehicles (HEVs) developed and mass-produced by our company. EV-95 for EVs enables a vehicle to drive approximately 200 km per charge. As the specific power is extremely high, more than 200 W/kg at 80% depth of discharge (DOD), the acceleration performance is equivalent to that of gasoline fuel automobiles. The life characteristic is also superior. This battery gives the satisfactory result of more than 1000 cycles in bench tests and approximately 4-year on-board driving. EV-28 developed for small EVs comprises of a compact and light battery module with high specific power of 300 W/kg at 80% DOD by introducing a new technology for internal cell connection. Meanwhile, our cylindrical battery for the HEV was adopted into the first generation Toyota Prius in 1997 which is the world's first mass-product HEV, and has a high specific power of 600 W/kg. Its life characteristic was found to be equivalent to more than 100,000 km driving. Furthermore, a new prismatic module in which six cells are connected internally was used for the second generation Prius in 2000. The prismatic battery comprises of a compact and light battery pack with a high specific power of 1000 W/kg, which is approximately 1.7 times that of conventional cylindrical batteries, as a consequence of the development of a new internal cell connection and a new current collection structure.

  6. 3WCC Temperature Integration in a Gasoline-HEV Optimal Energy Management Strategy

    Directory of Open Access Journals (Sweden)

    Pierre Michel

    2014-02-01

    Full Text Available For a gasoline-hybrid electric vehicle (HEV, the energy management strategy (EMS is the computation of the distribution between electric and gasoline propulsion. Until recently, the EMS objective was to minimize fuel consumption. However, decreasing fuel consumption does not directly minimize the pollutant emissions, and the 3-way catalytic converter (3WCC must be taken into account. This paper proposes to consider the pollutant emissions in the EMS, by minimizing, with the Pontryagin minimum principle, a tradeoff between pollution and fuel consumption. The integration of the 3WCC temperature in the EMS is discussed and finally a simplification is proposed.

  7. Toward single cell traction microscopy within 3D collagen matrices

    International Nuclear Information System (INIS)

    Hall, Matthew S.; Long, Rong; Feng, Xinzeng; Huang, YuLing; Hui, Chung-Yuen; Wu, Mingming

    2013-01-01

    Mechanical interaction between the cell and its extracellular matrix (ECM) regulates cellular behaviors, including proliferation, differentiation, adhesion, and migration. Cells require the three-dimensional (3D) architectural support of the ECM to perform physiologically realistic functions. However, current understanding of cell–ECM and cell–cell mechanical interactions is largely derived from 2D cell traction force microscopy, in which cells are cultured on a flat substrate. 3D cell traction microscopy is emerging for mapping traction fields of single animal cells embedded in either synthetic or natively derived fibrous gels. We discuss here the development of 3D cell traction microscopy, its current limitations, and perspectives on the future of this technology. Emphasis is placed on strategies for applying 3D cell traction microscopy to individual tumor cell migration within collagen gels. - Highlights: • Review of the current state of the art in 3D cell traction force microscopy. • Bulk and micro-characterization of remodelable fibrous collagen gels. • Strategies for performing 3D cell traction microscopy within collagen gels

  8. Toward single cell traction microscopy within 3D collagen matrices

    Energy Technology Data Exchange (ETDEWEB)

    Hall, Matthew S. [Department of Biological and Environmental Engineering, Cornell University, Ithaca, NY 14853 (United States); Long, Rong [Department of Mechanical Engineering, University of Alberta, Edmonton, AB, Canada T6G 2G8 (Canada); Feng, Xinzeng [Department of Mechanical and Aerospace Engineering, Cornell University, Ithaca, NY 14853 (United States); Huang, YuLing [Department of Biological and Environmental Engineering, Cornell University, Ithaca, NY 14853 (United States); Hui, Chung-Yuen [Department of Mechanical and Aerospace Engineering, Cornell University, Ithaca, NY 14853 (United States); Wu, Mingming, E-mail: mw272@cornell.edu [Department of Biological and Environmental Engineering, Cornell University, Ithaca, NY 14853 (United States)

    2013-10-01

    Mechanical interaction between the cell and its extracellular matrix (ECM) regulates cellular behaviors, including proliferation, differentiation, adhesion, and migration. Cells require the three-dimensional (3D) architectural support of the ECM to perform physiologically realistic functions. However, current understanding of cell–ECM and cell–cell mechanical interactions is largely derived from 2D cell traction force microscopy, in which cells are cultured on a flat substrate. 3D cell traction microscopy is emerging for mapping traction fields of single animal cells embedded in either synthetic or natively derived fibrous gels. We discuss here the development of 3D cell traction microscopy, its current limitations, and perspectives on the future of this technology. Emphasis is placed on strategies for applying 3D cell traction microscopy to individual tumor cell migration within collagen gels. - Highlights: • Review of the current state of the art in 3D cell traction force microscopy. • Bulk and micro-characterization of remodelable fibrous collagen gels. • Strategies for performing 3D cell traction microscopy within collagen gels.

  9. Targeted traction of impacted teeth with C-tube miniplates.

    Science.gov (United States)

    Chung, Kyu-Rhim; Kim, Yong; Ahn, Hyo-Won; Lee, Dongjoo; Yang, Dong-Min; Kim, Seong-Hun; Nelson, Gerald

    2014-09-01

    Orthodontic traction of impacted teeth has typically been performed using full fixed appliance as anchorage against the traction force. This conventional approach can be difficult to apply in the mixed dentition if the partial fixed appliance offers an insufficient anchor unit. In addition, full fixed appliance can induce unwanted movement of adjacent teeth. This clinical report presents 3 cases where impacted teeth were recovered in the mixed or transitional dentition with skeletal anchorage on the opposite arch without full fixed appliance. Instead, intermaxillary traction was used to bring the impacted teeth into position. With this approach, side effects on teeth and periodontal tissues adjacent to the impaction were minimized.

  10. Integrated Cooling System for Induction Motor Traction Drives, CARAT Program Phase Two Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Konrad, Charles E. [VPT, Inc., Blacksburg, VA (United States)

    2002-12-03

    the past. A primary goal of this program was the development of an efficient, reliable, 20,000 rpm induction motor traction system. Induction motors that have been built to operate in traction applications at speeds above 15,000 rpm employed special endring structures that resulted in unacceptably high motor costs. Present induction motor manufacturing use cast aluminum endrings to minimize cost, and have become relatively common in traction applications at speeds up to 10,000 rpm. The use of induction motors with cast aluminum for traction purposes at speeds above 10,000 RPM has not been explored. In addition to the improvements in power density and power volume promised through an increase in motor operational speed, this program also added significant improvements to the overall powertrain to improve the system reliability, system efficiency, and reductions in the system cost.

  11. Lower-Energy Energy Storage System (LEESS) Evaluation in a Full-Hybrid Electric Vehicle (HEV) (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Cosgrove, J.; Gonder, J.; Pesaran, A.

    2013-11-01

    The cost of hybrid electric vehicles (HEVs) (e.g., Toyota Prius or Ford Fusion Hybrid) remains several thousand dollars higher than the cost of comparable conventional vehicles, which has limited HEV market penetration. The battery energy storage device is typically the component with the greatest contribution toward this cost increment, so significant cost reductions/performance improvements to the energy storage system (ESS) can improve the vehicle-level cost-benefit relationship, which would in turn lead to larger HEV market penetration and greater aggregate fuel savings. The National Renewable Energy Laboratory (NREL) collaborated with a United States Advanced Battery Consortium (USABC) Workgroup to analyze trade-offs between vehicle fuel economy and reducing the minimum energy requirement for power-assist HEVs. NREL's analysis showed that significant fuel savings could still be delivered from an ESS with much lower energy storage than previous targets, which prompted the United States Advanced Battery Consortium (USABC) to issue a new set of lower-energy ESS (LEESS) targets that could be satisfied by a variety of technologies, including high-power batteries or ultracapacitors. NREL has developed an HEV test platform for in-vehicle performance and fuel economy validation testing of the hybrid system using such LEESS devices. This presentation describes development of the vehicle test platform and in-vehicle evaluation results using a lithium-ion capacitor ESS-an asymmetric electrochemical energy storage device possessing one electrode with battery-type characteristics (lithiated graphite) and one with ultracapacitor-type characteristics (carbon). Further efforts include testing other ultracapacitor technologies in the HEV test platform.

  12. Degree of Fault Tolerance as a Comprehensive Parameter for Reliability Evaluation of Fault Tolerant Electric Traction Drives

    Directory of Open Access Journals (Sweden)

    Igor Bolvashenkov

    2016-09-01

    Full Text Available This paper describes a new approach and methodology of quantitative assessment of the fault tolerance of electric power drive consisting of the multi-phase traction electric motor and multilevel electric inverter. It is suggested to consider such traction drive as a system with several degraded states. As a comprehensive parameter for evaluating of the fault tolerance, it is proposed to use the criterion of degree of the fault tolerance. For the approbation of the proposed method, the authors carried out research and obtained results of its practical application for evaluating the fault tolerance of the power train of an electrical helicopter.

  13. Experimental and numerical study of flows in PEM fuel cell stacks for traction applications; Etude numerique et experimentale des ecoulements dans une pile a combustible de type PEM adaptable aux applications embarquees

    Energy Technology Data Exchange (ETDEWEB)

    Picot, D

    1998-07-01

    The problems with the optimization and design of proton exchange membrane fuel cells (PEMFC) are mainly based on the mastery of water and heat transfers inside the active cells. A theoretical and experimental discussion about this topic is proposed. The average sharing coefficients of the generated water are measured for 3 Nora fuel cells (1, 5 and 10 kW). The values obtained with nafion 117 are in agreement with the data of the literature, while the 40% generated water recovered inside the anode compartment with nafion 115 are unexpected. The difficulty to obtain a physical formulation of electro-osmosis does not allow to quantify this coefficient and leads to justify the limitations of use of the numerical codes on this topic. However, by separating the intrinsic parameters of the electrodes/membrane system and the global operation parameters of a cell, it is possible to extrapolate realistic humidification strategies. In the framework of the European project 'Fever', a systemic model of a 30 kW module for electric-powered vehicle has been developed. For an optimum energy integration of Nora fuel cells in volume-limited applications, it is necessary to separate the humidification sections of these modules. In the case where air is used as oxidant, the presence of nitrogen inside the anode compartment has been evidenced both in close and recirculation modes. In agreement with the literature data about nafion permeability, the nitrogen migration through the electrolyte is explained by the diffusion theory. A discussion about the interest of using both operational modes to maximize the energy efficiency is proposed. Finally, a simple-phase and double-phase numerical study with interface reconstruction is carried out using the resolution of Navier-Stokes equations in Eulerian formalism in order to consider the problems linked with the internal flows inside the collectors of Nora cells. (J.S.)

  14. Adaptive control system of dump truck traction electric drive

    Science.gov (United States)

    Bolshunova, O. M.; Korzhev, A. A.; Kamyshyan, A. M.

    2018-03-01

    The paper describes the operational factors that determine the accident rate of a quarry motor vehicle and assessment of their impact on the choice of the operation mode of the traction drive control system.

  15. Intravitreal injection of perfluoropropane for the treatment of vitreomacular traction

    Directory of Open Access Journals (Sweden)

    Xiao-Ping Wan

    2013-07-01

    Full Text Available AIM: To study the efficacy of a single intravitreal injection of perfluoropropane(C3F8in releasing vitreomacular traction. METHODS: Twelve eyes of 12 consecutive patients with vitreomacular traction received a single intravitreal injection of 0.3mL 100%(C3F8were retrospectively analyzed. The best corrected vision acuity and the neural epithelium thickness of central macular were observed. RESULTS: One month following treatment, vitreomacular traction was released in 5 eyes(42%, mean final visual acuity(VAimproved 0.04 and mean central foveal thickness decreased by 69μm. The vision acuity before and after treatment were 0.20±0.07, 0.25±0.04 respectively.CONCLUSION: Intravitreal C3F8 injection could offer a minimally invasive alternative to pars plana vitrectomy in patients with vitreomacular traction.

  16. THE FLOW ANALYSIS ABOUT TRACTION OF QUARRY TRAINS

    Directory of Open Access Journals (Sweden)

    G. K. Getman

    2010-04-01

    Full Text Available The method of determination of constituents of expense of electric power on traction of quarry trains is resulted in the article, and also the degree of their intercommunication with the mode of train motion is analysed.

  17. INTELLIGENT DIAGNOSTIC SYSTEM OF EMERGENCY SITUATIONS IN TRACTION SUBSTATIONS DC

    Directory of Open Access Journals (Sweden)

    Sh. N. Nasyrov

    2009-09-01

    Full Text Available In the article the architecture and algorithm of operating an expert system providing the efficiency of functioning the electric equipment for traction substation as well as the four-parameter belonging function are determined.

  18. BACKGROUNDS OF EXPERIMENTAL INVESTIGATION OF ELECTROMAGNETIC COMPATIBILITY OF TRACTION ASYNCHRONOUS ELECTRIC DRIVES IN THE STRUCTURE OF DC TRACTION POWER SUPPLY SYSTEM

    Directory of Open Access Journals (Sweden)

    YU. S. Bondarenko

    2014-04-01

    Full Text Available Purpose. Application of physical modeling as a tool for research of any events or systems is becoming more widespread, including the field of railway transport. At the same time the adequacy of results that can be obtained, depends largely on the similarity degree of the physical model to real system. From the standpoint of the traction asynchronous electric drive (TAED research together with the traction power supply system research, the similarity can not be determined by the direct proportion of the parameters, because the processes nature accompanying the operation of these systems is non-linear. These features should be taken into account in the experimental setup, the basis for constructing of which is establishing of the system similarity that defines the purpose of this paper. Methodology. At the heart of the experimental setup creation laid reproduction of processes of energy transformation in the system of the DC traction power supply. Determination of the similarity degree of the proposed facility to the real system was carried out using the basic theorems of the similarity theory, their additional provisions on the complexity and nonlinear systems, as well as elements of mathematical analysis. Findings. According to the results of work: 1 The block diagram, the energy conversion mechanism of which is similar to the real system was received. This scheme is the basis of experimental setup, built in the future for the study of electromagnetic compatibility of TAED in the structure of DC traction electric power supply system. 2 Similarity of obtained structural scheme with the real system with the mechanism definition of calculating the scaling relations was established. Originality. In the process of establishing the similarity a simplified method for determining the scaling relations for nonlinear systems was suggested. They are identical in their structure components, but have different capacities. Practical value. Experimental

  19. TRACTION RESISTANCE IN CHITOSAN TREATED COTTON

    Directory of Open Access Journals (Sweden)

    LOX Wouter

    2015-05-01

    Full Text Available Nowadays natural products interest has increased. However, when some products are included on textile fibers, they have no affinity and need some binders or other kind of auxiliaries to improve the yeld of the process, and some of them are not so natural as the product which are binding and consequently the “bio” definition is missed as some of them can be considered as highly pollutant. Chitosan is a common used bonding agent for cotton. It improves the antimicrobial and antifungal activity, improves wound healing and is a non-toxic bonding agent. The biopolymer used in this work is chitosan, which is a deacetylated derivative of chitin. These properties depend on the amount of deacetylation (DD and the Molecular weight (MW. Along with these improving properties, as it requires some acid pH to ve solved the treatment with chitosan can have some decreasing mechanical properties. The aim of that paper is to evaluate the change in breaking force of the treated samples and a change in elongation of those samples. It compared different amounts of concentration of chitosan with non treated cotton. The traction resistance test were performed on a dynamometer. The test was conducted according to the UNE EN ISO 13934-1 standard.

  20. Traction force microscopy of engineered cardiac tissues.

    Science.gov (United States)

    Pasqualini, Francesco Silvio; Agarwal, Ashutosh; O'Connor, Blakely Bussie; Liu, Qihan; Sheehy, Sean P; Parker, Kevin Kit

    2018-01-01

    Cardiac tissue development and pathology have been shown to depend sensitively on microenvironmental mechanical factors, such as extracellular matrix stiffness, in both in vivo and in vitro systems. We present a novel quantitative approach to assess cardiac structure and function by extending the classical traction force microscopy technique to tissue-level preparations. Using this system, we investigated the relationship between contractile proficiency and metabolism in neonate rat ventricular myocytes (NRVM) cultured on gels with stiffness mimicking soft immature (1 kPa), normal healthy (13 kPa), and stiff diseased (90 kPa) cardiac microenvironments. We found that tissues engineered on the softest gels generated the least amount of stress and had the smallest work output. Conversely, cardiomyocytes in tissues engineered on healthy- and disease-mimicking gels generated significantly higher stresses, with the maximal contractile work measured in NRVM engineered on gels of normal stiffness. Interestingly, although tissues on soft gels exhibited poor stress generation and work production, their basal metabolic respiration rate was significantly more elevated than in other groups, suggesting a highly ineffective coupling between energy production and contractile work output. Our novel platform can thus be utilized to quantitatively assess the mechanotransduction pathways that initiate tissue-level structural and functional remodeling in response to substrate stiffness.

  1. Tractional retinal detachment in Usher syndrome type II.

    Science.gov (United States)

    Rani, Alka; Pal, Nikhil; Azad, Raj Vardhan; Sharma, Yog Raj; Chandra, Parijat; Vikram Singh, Deependra

    2005-08-01

    Retinal detachment is a rare complication in patients with retinitis pigmentosa. A case is reported of tractional retinal detachment in a patient with retinitis pigmentosa and sensorineural hearing loss, which was diagnosed as Usher syndrome type II. Because of the poor visual prognosis, the patient refused surgery in that eye. Tractional retinal detachment should be added to the differential diagnoses of visual loss in patients with retinitis pigmentosa.

  2. Traction Stresses Exerted by Adherent Cells: From Angiogenesis to Metastasis

    Science.gov (United States)

    Reinhart-King, Cynthia

    2010-03-01

    Cells exert traction stresses against their substrate that mediate their ability to sense the mechanical properties of their microenvironment. These same forces mediate cell adhesion, migration and the formation of stable cell-cell contacts during tissue formation. In this talk, I will present our data on the traction stresses generated by endothelial cells and metastatic breast cancer cells focused on understanding the processes of angiogenesis and metastasis, respectively. In the context of capillary formation, our data indicate that the mechanics of the substrate play a critical role in establishing endothelial cell-cell contacts. On more compliant substrates, endothelial cell shape and traction stresses polarize and promote the formation of stable cell-cell contacts. On stiffer substrates, traction stresses are less polarized and cell connectivity is disrupted. These data indicate that the mechanical properties of the microenvironment may drive cell connectivity and the formation of stable cell-cell contacts through the reorientation of traction stresses. In our studies of metastatic cell migration, we have found that traction stresses increase with increasing metastatic potential. We investigated three lines of varying metastatic potential (MCF10A, MCF7 and MDAMB231). MDAMB231, which are the most invasive, exert the most significant forces as measured by Traction Force Microscopy. These data present the possibility that cellular traction stress generation aids in the ability of metastatic cells to migrate through the matrix-dense tumor microenvironment. Such measurements are integral to link the mechanical and chemical microenvironment with the resulting response of the cell in health and disease.

  3. Energy and wear optimisation of train longitudinal dynamics and of traction and braking systems

    Science.gov (United States)

    Conti, R.; Galardi, E.; Meli, E.; Nocciolini, D.; Pugi, L.; Rindi, A.

    2015-05-01

    Traction and braking systems deeply affect longitudinal train dynamics, especially when an extensive blending phase among different pneumatic, electric and magnetic devices is required. The energy and wear optimisation of longitudinal vehicle dynamics has a crucial economic impact and involves several engineering problems such as wear of braking friction components, energy efficiency, thermal load on components, level of safety under degraded or adhesion conditions (often constrained by the current regulation in force on signalling or other safety-related subsystem). In fact, the application of energy storage systems can lead to an efficiency improvement of at least 10% while, as regards the wear reduction, the improvement due to distributed traction systems and to optimised traction devices can be quantified in about 50%. In this work, an innovative integrated procedure is proposed by the authors to optimise longitudinal train dynamics and traction and braking manoeuvres in terms of both energy and wear. The new approach has been applied to existing test cases and validated with experimental data provided by Breda and, for some components and their homologation process, the results of experimental activities derive from cooperation performed with relevant industrial partners such as Trenitalia and Italcertifer. In particular, simulation results are referred to the simulation tests performed on a high-speed train (Ansaldo Breda Emu V250) and on a tram (Ansaldo Breda Sirio Tram). The proposed approach is based on a modular simulation platform in which the sub-models corresponding to different subsystems can be easily customised, depending on the considered application, on the availability of technical data and on the homologation process of different components.

  4. Comportement mécanique des tuyaux. Influence de la traction, de la pression et du poids linéique. Application aux risers Mechanical Behavior of Pipes and Risers. Influence of Tension, Pressure and Weight

    Directory of Open Access Journals (Sweden)

    Sparks C.

    2006-11-01

    Full Text Available L'influence de la traction, de la pression et du poids linéique sur le comportement d'un tuyau (ou d'un riser a déjà été traitée dans de nombreux articles. Malgré cela, elle est fréquemment mal comprise, ce qui a parfois de; conséquences sérieuses. Par souci de clarté, l'approche de cet article est délibérément très élémentaire. Les problèmes principaux de la flexion, du flambage, de l'allongement et de la contrainte limite, qui sont souvent traités dans des articles différents, sont ici étudiés ensemble d'une façon homogène. On présente des interprétation: physiques, faciles à visualiser, des deux concepts de tension effective et de contrainte effective, dont l'utilisation est très répandue, ainsi que leur rapport avec des notions analogues dans d'autres domaines de l'art de l'ingénieur. La puissance de ces deux concepts est démontrée à la fin de l'article où ils sont utilisés pour résoudre huit problèmes divers. The influence of tension, pressure, and weight on different aspects of pipe and riser behavior has already been the subject of many articles (see references. In spite of this it has frequently been misunderstood, sometimes with serious consequences. The object of this payer is to explain the subject clearly and the approach is therefore deliberately very elementary. The principal problems of bending, buckling, yielding and strains, usually treated in separated papers, are here treated homogeneously. The widely used concepts of effective tension and effective stress are given interpretations, easy to visualise, which are related to analogous concepts in other engineering fields. Finally, eight diverse particular examples of the influence of tension, pressure and weight on pipe and riser behavior, are discussed.

  5. DVD. Alar Niineväli soovitab "Tähevärav : Tõelaegas" / Alar Niineväli

    Index Scriptorium Estoniae

    Niineväli, Alar

    2008-01-01

    Esimene kahest otse DVD levisse läinud mängufilmist populaarse ulmeseriaali lõpuleviimiseks "Tähevärav: Tõelaegas" ("Stargate: The Ark of Truth") : režissöör Robert C. Cooper : Ameerika Ühendriigid - Kanada 2008

  6. On the design of a (H)EV steerable warning device using acoustic beam forming and advanced numerical acoustic simulation

    NARCIS (Netherlands)

    Van Genechten, B.; Vansant, K.; Berkhoff, Arthur P.

    2014-01-01

    This paper describes the simulation-based design methodology used in the eVADER project for the development of targeted acoustic warning devices for increased detectability of Hybrid and Electric Vehicles (HEVs) while, at the same time, reducing urban noise pollution. A key component of this system

  7. Population Movement and Virus Spreading: HEV Spreading in a Pilgrimage City, Mashhad in Northeast Iran; an Example.

    Science.gov (United States)

    Ahmadi Ghezeldasht, Sanaz; Miri, Rahele; Hedayatimoghadam, Mohamadreza; Shamsian, Aliakbar; Bidkhori, Hamidreza; Fathimoghadam, Fahad; Rezaee, Seyyed Abdorrahim

    2013-01-01

    Hepatitis E Virus (HEV) infection is a significant public health concern and responsible for large outbreaks of acute hepatitis in poor sanitary and living conditions. To investigate the impact of population movements on virus spreading, a large-scale population-based survey was performed in a pilgrimage- tourism area, the great Mashhad, capital city of Khorasan province. A cross-sectional study was carried out among 1582 randomly selected individuals from general population of Mashhad, north east of Iran, between May to September 2009. Serum samples were tested for total anti-HEV antibody using a specific enzyme linked immunoassay (ELISA) kit. The prevalence of HEV infection was 14.2% (225/1582) with a maximum of 25.5 % (14/55) in densely populated areas. The highest prevalence was observed in visitant areas (≥ 20%) near the holly shrine with crowded hotels and inns. The differences between these areas and other districts were statistically significant (P socio-economic status, Illiterate individuals were significantly at higher risk for infection than educated persons (P < 0.001). These findings demonstrated that, high prevalence of HEV is related to populated district, which can reach to the highest rate in hotels and inns close to visitants. Traditional sanitation and water supplying systems are the second important factor for the virus transmission. Therefore, it can be concluded that such areas need efficient surveillance systems to prevent the spreading of infectious diseases.

  8. Diagnosis of HEV infection by serological and real-time PCR assays: a study on acute non-A-C hepatitis collected from 2004 to 2010 in Italy

    Directory of Open Access Journals (Sweden)

    Candido Angela

    2012-06-01

    Full Text Available Abstract Background The impact of hepatitis E in developed countries, like Italy, still requires a clear definition. In the present study, we evaluated HEV infection in patients with acute non-A-C hepatitis by an approach comparing data from Real-time PCR and serological assays. Methods In a first analysis, sera from 52 patients hospitalized with a diagnosis of acute viral non-A-C hepatitis in Italy were tested by in-house Real-Time PCR assay for identification of Hepatitis E Virus (HEV RNA and by anti-HEV IgM and IgG assays. In a subsequent analysis, selected samples were evaluated by additional IgM tests to confirm diagnosis. Results Among the 52 samples, 21 showed positive results for all three markers (IgM, IgG and HEV RNA. One patient showed HEV RNA as single marker. Uncertain results were found in 8 samples while the remaining 22 were negative for all markers. Further analysis of the 8 undefined samples by additional IgM tests confirmed HEV infection in 1 patient. Overall, acute HEV infections were reliably identified in 23 (44.2% out of 52 patients. Conclusions In the present paper, we performed a study evaluating HEV infection in 52 sporadic non-A-C acute hepatitis cases. All samples were collected from 2004 to 2010 in Italy. By a diagnostic strategy based on genomic and serological assays we identified HEV infections in 23 out of 52 patients (44.2%, a percentage higher than previous estimates. Thus, the actual impact of HEV infections in Italy needs to be further evaluated on a national scale by a diagnostic strategy based on multiple and last generation assays.

  9. Permanent Magnet Synchronous Motor with Different Rotor Structures for Traction Motor in High Speed Trains

    Directory of Open Access Journals (Sweden)

    Marcel Torrent

    2018-06-01

    Full Text Available In this work we proposed to study the use of permanent magnet synchronous motors (PMSM for railway traction in the high-speed trains (HST of Renfe Operadora (the Spanish national railway operator. Currently, induction motors (IM are used in AVE classes 102–112 trains, so, the IM used as a traction motor in these trains has been studied and characterized by comparing the results with data provided by Renfe. A PMSM of equivalent power to the IM has been dimensioned, and different electromagnetic structures of the PMSM rotor have been evaluated. The simulation by the finite element method and analysis of the equivalent electrical circuit used in all the motors have been studied to evaluate the performance of the motors in this application. Efficiency is calculated at different operating points due to its impact on the energy consumption of railway traction. The implementation of the PMSM evaluated is recommended, mainly due to the improvements achieved in efficiency as compared with the IM currently used.

  10. Traction force dynamics predict gap formation in activated endothelium

    Energy Technology Data Exchange (ETDEWEB)

    Valent, Erik T.; Nieuw Amerongen, Geerten P. van; Hinsbergh, Victor W.M. van; Hordijk, Peter L., E-mail: p.hordijk@vumc.nl

    2016-09-10

    In many pathological conditions the endothelium becomes activated and dysfunctional, resulting in hyperpermeability and plasma leakage. No specific therapies are available yet to control endothelial barrier function, which is regulated by inter-endothelial junctions and the generation of acto-myosin-based contractile forces in the context of cell-cell and cell-matrix interactions. However, the spatiotemporal distribution and stimulus-induced reorganization of these integral forces remain largely unknown. Traction force microscopy of human endothelial monolayers was used to visualize contractile forces in resting cells and during thrombin-induced hyperpermeability. Simultaneously, information about endothelial monolayer integrity, adherens junctions and cytoskeletal proteins (F-actin) were captured. This revealed a heterogeneous distribution of traction forces, with nuclear areas showing lower and cell-cell junctions higher traction forces than the whole-monolayer average. Moreover, junctional forces were asymmetrically distributed among neighboring cells. Force vector orientation analysis showed a good correlation with the alignment of F-actin and revealed contractile forces in newly formed filopodia and lamellipodia-like protrusions within the monolayer. Finally, unstable areas, showing high force fluctuations within the monolayer were prone to form inter-endothelial gaps upon stimulation with thrombin. To conclude, contractile traction forces are heterogeneously distributed within endothelial monolayers and force instability, rather than force magnitude, predicts the stimulus-induced formation of intercellular gaps. - Highlights: • Endothelial monolayers exert dynamic- and heterogeneous traction forces. • High traction forces correlate with junctional areas and the F-actin cytoskeleton. • Newly formed inter-endothelial gaps are characterized by opposing traction forces. • Force stability is a key feature controlling endothelial permeability.

  11. Traction force dynamics predict gap formation in activated endothelium

    International Nuclear Information System (INIS)

    Valent, Erik T.; Nieuw Amerongen, Geerten P. van; Hinsbergh, Victor W.M. van; Hordijk, Peter L.

    2016-01-01

    In many pathological conditions the endothelium becomes activated and dysfunctional, resulting in hyperpermeability and plasma leakage. No specific therapies are available yet to control endothelial barrier function, which is regulated by inter-endothelial junctions and the generation of acto-myosin-based contractile forces in the context of cell-cell and cell-matrix interactions. However, the spatiotemporal distribution and stimulus-induced reorganization of these integral forces remain largely unknown. Traction force microscopy of human endothelial monolayers was used to visualize contractile forces in resting cells and during thrombin-induced hyperpermeability. Simultaneously, information about endothelial monolayer integrity, adherens junctions and cytoskeletal proteins (F-actin) were captured. This revealed a heterogeneous distribution of traction forces, with nuclear areas showing lower and cell-cell junctions higher traction forces than the whole-monolayer average. Moreover, junctional forces were asymmetrically distributed among neighboring cells. Force vector orientation analysis showed a good correlation with the alignment of F-actin and revealed contractile forces in newly formed filopodia and lamellipodia-like protrusions within the monolayer. Finally, unstable areas, showing high force fluctuations within the monolayer were prone to form inter-endothelial gaps upon stimulation with thrombin. To conclude, contractile traction forces are heterogeneously distributed within endothelial monolayers and force instability, rather than force magnitude, predicts the stimulus-induced formation of intercellular gaps. - Highlights: • Endothelial monolayers exert dynamic- and heterogeneous traction forces. • High traction forces correlate with junctional areas and the F-actin cytoskeleton. • Newly formed inter-endothelial gaps are characterized by opposing traction forces. • Force stability is a key feature controlling endothelial permeability.

  12. Construction of an infectious cDNA clone of avian hepatitis E virus (avian HEV) recovered from a clinically healthy chicken in the United States and characterization of its pathogenicity in specific-pathogen-free chickens.

    Science.gov (United States)

    Kwon, Hyuk Moo; LeRoith, Tanya; Pudupakam, R S; Pierson, F William; Huang, Yao-Wei; Dryman, Barbara A; Meng, Xiang-Jin

    2011-01-27

    A genetically distinct strain of avian hepatitis E virus (avian HEV-VA strain) was isolated from a healthy chicken in Virginia, and thus it is important to characterize and compare its pathogenicity with the prototype strain (avian HEV-prototype) isolated from a diseased chicken. Here we first constructed an infectious clone of the avian HEV-VA strain. Capped RNA transcripts from the avian HEV-VA clone were replication-competent after transfection of LMH chicken liver cells. Chickens inoculated intrahepatically with RNA transcripts of avian HEV-VA clone developed active infection as evidenced by fecal virus shedding, viremia, and seroconversion. To characterize the pathogenicity, RNA transcripts of both avian HEV-VA and avian HEV-prototype clones were intrahepatically inoculated into the livers of chickens. Avian HEV RNA was detected in feces, serum and bile samples from 10/10 avian HEV-VA-inoculated and 9/9 avian HEV-prototype-inoculated chickens although seroconversion occurred only in some chickens during the experimental period. The histopathological lesion scores were lower for avian HEV-VA group than avian HEV-prototype group in the liver at 3 and 5 weeks post-inoculation (wpi) and in the spleen at 3 wpi, although the differences were not statistically significant. The liver/body weight ratio, indicative of liver enlargement, of both avian HEV-VA and avian HEV-prototype groups were significantly higher than that of the control group at 5 wpi. Overall, the avian HEV-VA strain still induces histological liver lesions even though it was isolated from a healthy chicken. The results also showed that intrahepatic inoculation of chickens with RNA transcripts of avian HEV infectious clone may serve as an alternative for live virus in animal pathogenicity studies. Copyright © 2010 Elsevier B.V. All rights reserved.

  13. Serological and virological survey of hepatitis E virus (HEV) in animal reservoirs from Uruguay reveals elevated prevalences and a very close phylogenetic relationship between swine and human strains.

    Science.gov (United States)

    Mirazo, Santiago; Gardinali, Noemí R; Cecilia, D'Albora; Verger, Lorenzo; Ottonelli, Florencia; Ramos, Natalia; Castro, Gustavo; Pinto, Marcelo A; Ré, Viviana; Pisano, Belén; Lozano, Alejandra; de Oliveira, Jaqueline Mendes; Arbiza, Juan

    2018-01-01

    Hepatitis E virus (HEV) infection is an issue of public health concern in high-income and non-endemic countries. Increasing evidence supports the hypothesis of a zoonotic route as the main mode of infection in this epidemiological setting, since the transmission of genotypes HEV-3 and HEV-4 from reservoirs to humans has been demonstrated. In America, studies have confirmed the circulation of HEV in pig herds but the zoonotic role of wild boars has never been evaluated. Uruguay has a high burden of HEV- associated acute hepatitis, and a close phylogenetic relationship was observed among human HEV-3 strains and European isolates detected in swine. However in this context, swine herds have never been surveyed. Herein is reported a survey of HEV in swine herds, pigs at slaughter-house and free-living wild boar populations. Two-hundred and twenty sera and 150 liver tissue samples from domestic pigs, and 140 sera from wild boars were tested for HEV by ELISA and PCR-based approaches. All tested swine farms resulted seropositive with an overall rate of 46.8%. In turn, 22.1% of the wild boars had anti-HEV antibodies. HEV RNA was detected in 16.6% and 9.3% of liver samples from slaughter-age pigs and adult wild boars sera, respectively. Three strains from domestic pig were also amplified by nested-PCR approaches. By contrast, none of the positive samples obtained from wild boars could be confirmed by nested-PCR. Phylogenetic analysis revealed a very high nucleotide identity among swine strains and sequences obtained from humans in Uruguay. Results showed that HEV is widely distributed among swine herds in Uruguay. Additionally, this study evidences for the first time in the American continent that wild boar populations are a reservoir for HEV, though its zoonotic role remains to be elucidated. Altogether, data presented here suggest a high zoonotic risk of HEV transmission from swine to humans. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Maximum Safety Regenerative Power Tracking for DC Traction Power Systems

    Directory of Open Access Journals (Sweden)

    Guifu Du

    2017-02-01

    Full Text Available Direct current (DC traction power systems are widely used in metro transport systems, with running rails usually being used as return conductors. When traction current flows through the running rails, a potential voltage known as “rail potential” is generated between the rails and ground. Currently, abnormal rises of rail potential exist in many railway lines during the operation of railway systems. Excessively high rail potentials pose a threat to human life and to devices connected to the rails. In this paper, the effect of regenerative power distribution on rail potential is analyzed. Maximum safety regenerative power tracking is proposed for the control of maximum absolute rail potential and energy consumption during the operation of DC traction power systems. The dwell time of multiple trains at each station and the trigger voltage of the regenerative energy absorbing device (READ are optimized based on an improved particle swarm optimization (PSO algorithm to manage the distribution of regenerative power. In this way, the maximum absolute rail potential and energy consumption of DC traction power systems can be reduced. The operation data of Guangzhou Metro Line 2 are used in the simulations, and the results show that the scheme can reduce the maximum absolute rail potential and energy consumption effectively and guarantee the safety in energy saving of DC traction power systems.

  15. The Simulation of the Traction Drive with Middle-Frequency Transformer

    Directory of Open Access Journals (Sweden)

    Pavel Drabek

    2008-01-01

    Full Text Available This paper presents research motivated by industrial demand for special traction drive topology devoted to minimization of traction transformer weight against topology with classical 50Hz traction transformer. The special traction drive topology for AC power systems consists of input high voltage trolley converter (single phase matrix converter –middle frequency transformer - output converter - traction motor has been described. The main attention has been given tothe control algorithm of the traction topology (inserting of NULL vector of matrix converter and Two-value control ofsecondary active rectifier.

  16. Contact traction analysis for profile change during coining process

    International Nuclear Information System (INIS)

    Kim, Hyung Kyu; Yoon, Kyung Ho; Kang, Heung Seok; Song, Kee Nam

    2002-01-01

    Contact tractions are analysed in the case of the change in contact profile occurring during the coining process of a thin strip material. The changed profile is assumed as a concave circular arc in the central part of the contact region which is smoothly connected with convex circular arcs at both sides, referring to the actual measurement of the coined material. The profile is discretized and the known solutions of singular integral equations are used. Since the contact profile affects the contact traction and relevant tribological behaviour (e.g. wear) as well, an accurate definition of the profile is necessary in the analysis of material failure. Parametric study is conducted with the variation of the radii and distance of the arcs, which defines the height difference between the summits of the arcs. Considered is the contact profile, which can give the negligible variation of the traction in comparison with that before the coining process

  17. A modification of the maitland roll top traction table.

    Science.gov (United States)

    Kneipp, K

    1975-03-01

    This modification of the Maitland Roll Top Traction Table (Maitland, 1973) differs from the original as follows: 1. The two weight-bearing leaves are enclosed by a "guide frame" and the "U-piece" of the original is replaced by a hinged "gate" at the foot, which can be opened downwards for lumbar traction, or can be locked to restrain the leaves when the table is required for other purposes. 2. Four rollers of light steel replace the wooden dowels. 3. The modified table in use by the author is held by a floor peg, and is set up be-between two walls 10' 6″ apart which provide purchase points for traction. Alternatively, purchase at the head end can be taken by hooks attached to the table itself. 4. The design permits a six-foot plinth to be used. Copyright © 1975 Australian Physiotherapy Association. Published by . All rights reserved.

  18. Traction sheave elevator, hoisting unit and machine space

    Science.gov (United States)

    Hakala, Harri; Mustalahti, Jorma; Aulanko, Esko

    2000-01-01

    Traction sheave elevator consisting of an elevator car moving along elevator guide rails, a counterweight moving along counterweight guide rails, a set of hoisting ropes (3) on which the elevator car and counterweight are suspended, and a drive machine unit (6) driving a traction sheave (7) acting on the hoisting ropes (3) and placed in the elevator shaft. The drive machine unit (6) is of a flat construction. A wall of the elevator shaft is provided with a machine space with its open side facing towards the shaft, the essential parts of the drive machine unit (6) being placed in the space. The hoisting unit (9) of the traction sheave elevator consists of a substantially discoidal drive machine unit (6) and an instrument panel (8) mounted on the frame (20) of the hoisting unit.

  19. Improved Battery Parameter Estimation Method Considering Operating Scenarios for HEV/EV Applications

    Directory of Open Access Journals (Sweden)

    Jufeng Yang

    2016-12-01

    Full Text Available This paper presents an improved battery parameter estimation method based on typical operating scenarios in hybrid electric vehicles and pure electric vehicles. Compared with the conventional estimation methods, the proposed method takes both the constant-current charging and the dynamic driving scenarios into account, and two separate sets of model parameters are estimated through different parts of the pulse-rest test. The model parameters for the constant-charging scenario are estimated from the data in the pulse-charging periods, while the model parameters for the dynamic driving scenario are estimated from the data in the rest periods, and the length of the fitted dataset is determined by the spectrum analysis of the load current. In addition, the unsaturated phenomenon caused by the long-term resistor-capacitor (RC network is analyzed, and the initial voltage expressions of the RC networks in the fitting functions are improved to ensure a higher model fidelity. Simulation and experiment results validated the feasibility of the developed estimation method.

  20. THE MEASUREMENT ELECTROMAGNETIC INTERFERENCE IN THE REVERSE TRACTION NETWORK

    Directory of Open Access Journals (Sweden)

    T. M. Serdiuk

    2009-09-01

    Full Text Available The original automated method of measurement of electrical noise in the return electric-traction network is proposed. It is realized on the base of car-laboratory “Automatics, telemechanics and communication”. The mathematic model of return electric-traction network is developed to scientific bases of automated measurement. It allows us obtaining the mathematic expressions for change of voltage and current harmonics in the rail net and taking into account the inhomogeneity of lines for the following analytic determination of a source of electric noise.

  1. Simple traction-immobilization device for CT scanners

    International Nuclear Information System (INIS)

    Robertson, J.; Federle, M.P.

    1983-01-01

    Successful computed tomographic (CT) scanning of acutely ill or traumatized patients often requires immobilization or traction of the extremities. Existing medical appliances and external fixation devices often are cumbersome, produce technical artifacts, or are uncomfortable for patients. This paper describes a traction-immobilization device that overcomes many of these difficulties. The authors have used this device successfully in several hundred cases and found that it markedly facilitated patient comfort and throughput. Construction is simple and inexpensive, using materials available in most hardware stores

  2. IMPLEMENTATION MODEL OF MOTOR TRACTION FORCE OF MAGLEV TRAIN

    Directory of Open Access Journals (Sweden)

    V. O. Polyakov

    2016-08-01

    Full Text Available Purpose. Traction force implementation (TFI by the motor of magnetic levitation train (MLT occurs in the process of electric-to-kinetic energy transformation at interaction of inductor and armature magnetic fields. Ac-cordingly, the aim of this study is to obtain a correct description of such energy transformation. Methodology. At the present stage, a mathematical and, in particular, computer simulation is the main and most universal tool for analysis and synthesis of processes and systems. At the same time, radical advantages of this tool make the precision of selection of a particular research methodology even more important. It is especially important for such a large and complex system as MLT. Therefore the special attention in the work is given to the rationale for choosing the research paradigm selective features. Findings. The analysis results of existing TFI process model versions indicate that each of them has both advantages and disadvantages. Therefore, one of the main results of this study was the creation of a mathematical model for such process that would preserve the advantages of previous versions, but would be free from their disadvantages. The work provides rationale for application (for the purposes of research of train motor TFI of the integrative holistic paradigm, which assimilates the advantages of the theory of electric circuit and magnetic field. Originality. The priority of creation of such paradigm and corresponding version of FI model constitute the originality of the research. Practical value. The main manifestation of practical value of this research in the opportunity, in case of use of its results, for significant increase in efficiency of MLT dynamic studies, on the condition that their generalized costs will not rise.

  3. Durability comparison of four different types of high-power batteries in HEV and their degradation mechanism analysis

    International Nuclear Information System (INIS)

    Yan, Dongxiang; Lu, Languang; Li, Zhe; Feng, Xuning; Ouyang, Minggao; Jiang, Fachao

    2016-01-01

    Highlights: • Utilize a realistic current profile for an HEV to study the degradation mechanism of batteries. • Compare the durability of four different types of high-power battery. • Degradation mechanisms of four different types of high-power battery are analyzed by IC curves. • The prognostic model is used to quantitatively clarify the aging mechanism of batteries. - Abstract: There are many types of high-power batteries used in HEVs, and their durabilities and degradation mechanisms are different. In this paper, four types of commercial high-power batteries, including two types of LTO/NCM lithium-ion battery from two different manufacturers, a C/LMO battery and a supercapacitor (SC), are studied. A durability test with a realistic current profile for an HEV is used so that the durability results more closely reflect real operating conditions than a general cycle life test. Incremental capacity (IC) curves are used to qualitatively analyze the degradation mechanism. To compensate for defects in the IC method, a prognosis model, using a genetic algorithm to reconstruct constant current charge voltage curves, is adopted to quantitatively identify the battery aging mechanism.

  4. Performance of a Nonlinear Real-Time Optimal Control System for HEVs/PHEVs during Car Following

    Directory of Open Access Journals (Sweden)

    Kaijiang Yu

    2014-01-01

    Full Text Available This paper presents a real-time optimal control approach for the energy management problem of hybrid electric vehicles (HEVs and plug-in hybrid electric vehicles (PHEVs with slope information during car following. The new features of this study are as follows. First, the proposed method can optimize the engine operating points and the driving profile simultaneously. Second, the proposed method gives the freedom of vehicle spacing between the preceding vehicle and the host vehicle. Third, using the HEV/PHEV property, the desired battery state of charge is designed according to the road slopes for better recuperation of free braking energy. Fourth, all of the vehicle operating modes engine charge, electric vehicle, motor assist and electric continuously variable transmission, and regenerative braking, can be realized using the proposed real-time optimal control approach. Computer simulation results are shown among the nonlinear real-time optimal control approach and the ADVISOR rule-based approach. The conclusion is that the nonlinear real-time optimal control approach is effective for the energy management problem of the HEV/PHEV system during car following.

  5. Electric vehicle traction motors - The development of an advanced motor concept

    Science.gov (United States)

    Campbell, P.

    1980-01-01

    An axial-field permanent magnet traction motor is described, similar to several advanced motors that are being developed in the United States. This type of machine has several advantages over conventional dc motors, particularly in the electric vehicle application. The rapidly changing cost of magnetic materials, particularly cobalt, makes it important to study the utilization of permanent magnet materials in such machines. The impact of different magnets on machine design is evaluated, and the advantages of using iron powder composites in the armature are assessed.

  6. Investigation into the traction system of battery-driven vehicle (electric motorcar) with super capacitors

    Energy Technology Data Exchange (ETDEWEB)

    Kuzomin, Oleksandr; Gurtovyi, Mykhailo; Kirylyuk, Artur; Pismenckiy, Viktor; Slipchenko, Mykola [Kharkiv National Univ. of Radio Electronics, Kharkiv (Ukraine)

    2012-11-01

    The results of investigations into the main characteristics of the traction system of the electric motorcar (EM) with application of super capacitors (SC) to the EM starting and acceleration regimes are given. Dynamics of the consumed power at the EM starting and acceleration up to the specified speed, taking into account its mass, acceleration time and aerodynamic characteristics, is investigated. The authors have developed the microcontroller device ensuring the decrease in the peak load on the accumulator battery (AB) at the moment of the EM starting and acceleration, as well as the automatic redistribution of the electric motor electrical supply between the SC and AB. (orig.)

  7. MODELING OF TRACTION SYNCHRONOUS PERMANENT MAGNET MOTOR MODES

    Directory of Open Access Journals (Sweden)

    Y.N. Vas’kovsky

    2013-10-01

    Full Text Available A mathematical model of electromagnetic field for simulating operational modes of traction synchronous motors with permanent magnets intended for electric vehicles is developed. The mathematical model takes into account real-time rotor rotation and allows calculating and analyzing the motor basic running characteristics as time functions.

  8. High resolution, large deformation 3D traction force microscopy.

    Directory of Open Access Journals (Sweden)

    Jennet Toyjanova

    Full Text Available Traction Force Microscopy (TFM is a powerful approach for quantifying cell-material interactions that over the last two decades has contributed significantly to our understanding of cellular mechanosensing and mechanotransduction. In addition, recent advances in three-dimensional (3D imaging and traction force analysis (3D TFM have highlighted the significance of the third dimension in influencing various cellular processes. Yet irrespective of dimensionality, almost all TFM approaches have relied on a linear elastic theory framework to calculate cell surface tractions. Here we present a new high resolution 3D TFM algorithm which utilizes a large deformation formulation to quantify cellular displacement fields with unprecedented resolution. The results feature some of the first experimental evidence that cells are indeed capable of exerting large material deformations, which require the formulation of a new theoretical TFM framework to accurately calculate the traction forces. Based on our previous 3D TFM technique, we reformulate our approach to accurately account for large material deformation and quantitatively contrast and compare both linear and large deformation frameworks as a function of the applied cell deformation. Particular attention is paid in estimating the accuracy penalty associated with utilizing a traditional linear elastic approach in the presence of large deformation gradients.

  9. Physical and electrocardiographic evaluation of horses used for wagon traction

    Directory of Open Access Journals (Sweden)

    M.M. Bomfim

    Full Text Available ABSTRACT The objective of this research was to evaluate the electrocardiogram (ECG of horses used for wagon traction and to compare the results with the parameters obtained from inactive horses or horses submitted to a training routine. Fifty-six 3-15-year-old healthy horses (22 females and 34 males were divided into three groups: control (without a work routine; N=21, wagon traction (N=25 and athlete (N=10 and submitted to physical examination and ECG (at rest. The rhythm, heart rate (HR, amplitude and duration of ECG waveforms and intervals were obtained from the frontal plane and base-apex leads. Heart score (HS was calculated using the arithmetic mean of QRS duration in LI, LII and LIII. Measurements of ECG waves were smaller in control group, in comparison with wagon traction and athlete groups, suggesting that exercise can change ECG. Similar results were observed in the wagon traction and athlete groups, but the electrophysiological adjustments to exercise were not the same for these groups.

  10. LOADING OF MECHANICAL TRANSMISSION OF TROLLEYBUS TRACTION DRIVING GEAR

    Directory of Open Access Journals (Sweden)

    A. I. Safonov

    2009-01-01

    Full Text Available The paper analyzes factors that determine dynamic loads of mechanical transmission of trolleybus traction driving gear. The paper proposes a methodology for determination of calculative moments of loading transmission elements. Results of the research are analyzed and recommendations on  dynamic reduction of trolleybus transmission are given in the paper. 

  11. COMPROMISE, OPTIMAL AND TRACTIONAL ACCOUNTS ON PARETO SET

    Directory of Open Access Journals (Sweden)

    V. V. Lahuta

    2010-11-01

    Full Text Available The problem of optimum traction calculations is considered as a problem about optimum distribution of a resource. The dynamic programming solution is based on a step-by-step calculation of set of points of Pareto-optimum values of a criterion function (energy expenses and a resource (time.

  12. Development of low AC loss windings for superconducting traction transformer

    International Nuclear Information System (INIS)

    Kamijo, H; Hata, H; Fukumoto, Y; Tomioka, A; Bohno, T; Yamada, H; Ayai, N; Yamasaki, K; Kato, T; Iwakuma, M; Funaki, K

    2010-01-01

    We have been developing a light weight and high efficiency superconducting traction transformer for railway rolling stock. We designed and fabricated a prototype superconducting traction transformer of a floor-mount type for Shinkansen rolling stock in 2004. We performed the type-test, the system-test, and the vibration-test. Consequently, we could verify that the transformer satisfied the requirement almost exactly as initially planned. However, there have been raised some problems to be solved to put superconducting traction transformer into practical use such that AC loss of the superconducting tape must be lower and the capacity of the refrigerator must be larger. Especially it is the most important to reduce the AC loss of superconducting windings for lightweight and high efficiency. The AC loss must be reduced near the theoretical value of superconducting tape with multifilament. In this study, we fabricated and evaluated the Bi2223 tapes as introduced various measures to reduce the AC loss. We confirmed that the AC loss of the narrow type of Bi2223 tapes with twist of filaments is lower, and we fabricated windings of this tape for use in superconducting traction transformer.

  13. Quality electricity lines of external power systems electric traction DC

    Directory of Open Access Journals (Sweden)

    A.V. Petrov

    2012-08-01

    Full Text Available The results of studies that compare and analyze the numerical values of some key indicators quality electricity in the lines of the external power supply system the electric traction DC. As a supplement are additional and fundamental values of energy losses in them.

  14. THE DYNAMICS AND TRACTION ENERGY METRICS LOCOMOTIVE VL40

    Directory of Open Access Journals (Sweden)

    S. V. Pylypenko

    2008-03-01

    Full Text Available In the article the results of dynamic running and traction-energy tests of the electric locomotive VL40U are presented. In accordance with the test results a conclusion about the suitability of electric locomotive of such a type for operation with trains containing up to 15 passenger coaches inclusive is made.

  15. Apicotomy as Treatment for Failure of Orthodontic Traction

    Directory of Open Access Journals (Sweden)

    Leandro Berni Osório

    2013-01-01

    Full Text Available Objective. The purpose of this study was to present a case report that demonstrated primary failure in a tooth traction that was subsequently treated with apicotomy technique. Case Report. A 10-year-old girl had an impacted upper right canine with increased pericoronal space, which was apparent on a radiographic image. The right maxillary sinus showed an opacity suggesting sinusitis. The presumptive diagnosis was dentigerous cyst associated with maxillary sinus infection. The plan for treatment included treatment of the sinus infection and cystic lesion and orthodontic traction of the canine after surgical exposure and bonding of an orthodontic appliance. The surgical procedure, canine position, root dilaceration, and probably apical ankylosis acted in the primary failure of the orthodontic traction. Surgical apical cut of the displaced teeth was performed, and tooth position in the dental arch was possible, with a positive response to the pulp vitality test. Conclusion. Apicotomy is an effective technique to treat severe canine displacement and primary orthodontic traction failure of palatally displaced canines.

  16. Novel characteristics of traction force in biliary self-expandable metallic stents.

    Science.gov (United States)

    Hori, Yasuki; Hayashi, Kazuki; Yoshida, Michihiro; Naitoh, Itaru; Ban, Tesshin; Miyabe, Katsuyuki; Kondo, Hiromu; Nishi, Yuji; Umemura, Shuichiro; Fujita, Yasuaki; Natsume, Makoto; Kato, Akihisa; Ohara, Hirotaka; Joh, Takashi

    2017-05-01

    In recent years, knowledge concerning the mechanical properties of self-expandable metallic stents (SEMS) has increased. In a previous study, we defined traction force and traction momentum and reported that these characteristics are important for optimal stent deployment. However, traction force and traction momentum were represented as relative values and were not evaluated in various conditions. The purpose of the present study was to measure traction force in various situations assumed during SEMS placement. Traction force and traction momentum were measured in non-stricture, stricture, and angled stricture models using in-house equipment. Stricture and angled stricture models had significantly higher traction force and traction momentum than those of the non-stricture model (stricture vs non-stricture: traction force, 7.2 N vs 1.4 N, P stent influenced the traction force. Clinicians should be aware of the transition of the traction force and should schedule X-ray imaging during SEMS placement. © 2017 Japan Gastroenterological Endoscopy Society.

  17. Influences of Traction Load Shock on Artificial Partial Discharge Faults within Traction Transformer—Experimental Test for Pattern Recognition

    Directory of Open Access Journals (Sweden)

    Shuaibing Li

    2017-10-01

    Full Text Available Partial discharge (PD measurement and its pattern recognition are vital to fault diagnosis of transformers, especially to those traction substation transformers undergoing repetitive traction load shocks. This paper presents the primary factors induced by traction load shocks including high total harmonics distortion (THD, transient voltage impulse and high-temperature rise, and their effects on the feature parameters of PD. Experimental tests are conducted on six artificial PD models with these factors introduced one by one. Results reveal that the maximum PD quantity and the PD repetitive rate are favorable to be enlarged when the oil temperature exceeds 80 °C or the THD is higher than 16% with certain orders of harmonic. The decline in PD inception voltage can mainly be attributed to the transient voltage impulse. The variation in central frequency of the fast Fourier transformation (FFT spectra transformed from ultra-high frequency signals can mainly be attributed to high THD, especially when it exceeds 20%. The temperature rise has no significant influence on the FFT spectra; the transient voltage impulse, however, can result in a central frequency shift of the floating particle discharge. With the rapid development of high-speed railways, the study presented in this paper will be helpful for field PD detection and recognition of traction substation transformers in the future.

  18. An assessment of available measures to reduce traction energy use in railway networks

    International Nuclear Information System (INIS)

    Douglas, Heather; Roberts, Clive; Hillmansen, Stuart; Schmid, Felix

    2015-01-01

    Highlights: • Railway networks are defined in terms of their distinguishing features. • Current energy saving measures are reviewed and categorised by the energy use they target. • The achievable energy savings of different measures are compared dependent on the network type. • The success of a measure depends on the characteristics of the network, vehicle and service. • Measures should be evaluated at system level due to interdependencies. - Abstract: Rail is becoming an increasingly popular choice to satisfy transportation demands locally, nationally and internationally, due to its inherent efficiency and high capacity. Despite this, operators are facing pressure to reduce rail energy consumption to meet efficiency targets, whilst still maintaining service quality and managing increased demand. A number of individual measures have been proposed to reduce energy in the rail sector, often showing good results on specific case studies. It is generally agreed that the attainable savings of a given measure change dependant on the route, vehicle and service characteristics. However, there is little information in the literature specifically regarding which measures are most suitable for given network types, or how they interact. This paper therefore aims to begin evaluating the available measures in terms of their suitability for different systems. Firstly, networks are defined in terms of their distinguishing features. As traction accounts for the majority of all energy use in the rail sector, the traction flow through a vehicle is considered as the starting point for an evaluation of measures. Current technologies and procedures are reviewed and categorised based on which area of traction use they target. Thought is given to the factors that affect implementation and the networks where they are applied. A key output of this paper is a comparison of the achievable energy savings of different measures dependent on the network type. It is hoped that this will

  19. THE CALCULATION OF THE ENERGY RECOVERY ELECTRIFIED URBAN TRANSPORT DURING THE INSTALLATION DRIVE FOR TRACTION SUBSTATION

    Directory of Open Access Journals (Sweden)

    A. A. Sulim

    2014-01-01

    Full Text Available At present a great attention is paid to increasing of energy efficiency at operated electrified urban transport. Perspective direction for increasing energy efficiency at that type of transport is the application of regenerative braking. For additional increasing of energy efficiency there were suggested the use of capacitive drive on tires of traction substation. One of the main task is the analysis of energy recovery application  with drive and without it.These analysis demonstrated that the calculation algorithms don’t allow in the full volume to carry out calculations of amount and cost of energy recovery without drive and with it. That is why we see the current interest to this topic. The purpose of work is to create methods of algorithms calculation for definite amount and cost of consumed, redundant and recovery energy of electrified urban transport due to definite regime of motion on wayside. There is algorithm developed, which allow to calculate amount and cost of consumed, redundant and recovery energy of electrified urban transport on wayside during the installation capacitive drive at traction substation. On the basis of developed algorithm for the definite regime of wagon motion of subway there were fulfilled the example of energy recovery amount and its cost calculation, among them with limited energy intensity drive, when there are 4 trains on wayside simultaneously.

  20. CONSTRUCTIVE MODELLING FOR ZONE OF RECOVERY ENERGY DISTRIBUTION OF DC TRACTION

    Directory of Open Access Journals (Sweden)

    V. I. Shynkarenko

    2016-10-01

    Full Text Available Purpose.The article is aimed to develop the means and methods of forming a plurality of real and potential structural diagrams for zones of energy recovery and different locations of trains for further training neuro-fuzzy networks on the basis of expert solutions and also for the formation of good control. Methodology. Methodology of mathematical and algorithmic constructivism for modeling the structural diagrams of the electric supply system and modes of traction power consumption and the train’s locations in zones of energy recovery was applied. This approach involves the development of constructive-synthesizing structures (CSS with transformation by specialization, interpretation, specification and implementation. Development CSS provides an extensible definition media, relations and the signature of operations and constructive axiomatic. The most complex and essential part of the axioms is the set formed by the substitution rules defining the process of withdrawal of the corresponding structures. Findings. A specialized and specified CSS, which allows considering all the possibilities and features, that supply power traction systems with modern equipment, stations and trains location was designed. Its feature: the semantic content of the terminal alphabet images of electrical traction network and power consumers with relevant attributes. A special case of the formation of the structural diagram shows the possibilities CSS in relation to this problem. Originality. A new approach to solving the problem of rational use of energy recovery, which consists in application of the methods and means of artificial neural networks, expert systems, fuzzy logic and mathematical and algorithmic constructivism. This paper presents the methods of constructive simulation of a production-distribution of energy recovery zone structure in the system of the DC traction. Practical value. The tasks decision of the rational use of energy recovery can

  1. Posture manipulation for rescue activity via small traction robots

    International Nuclear Information System (INIS)

    Iwano, Yuki; Osuka, Koichi; Amano, Hisanori

    2006-01-01

    We discuss a conceptual design of rescue robots against nuclear-power plant accidents. We claim that the rescue robots in nuclear-power plants should have the following properties. (1) The size is small. (2) The structure is simple. (3) The number of the robots is large. This paper studies the rescue robots to rescue people in an area polluted with radioactive leakage in nuclear power institutions. In particular, we propose a rescue system which consists of a group of small mobile robots. First, small traction robots set the posture of the fainted victims to carry easily, and carry them to the safety space with the mobile robots for the stretcher composition. In this paper, we describe the produced small traction robots. And, we confirm that the robots can manipulate a 40 kg dummy doll's posture. We also examine the optimal number of robots from a perspective of working efficiency in the assumption spot. (author)

  2. Fabrication of Superconducting Traction Transformer for Railway Rolling Stock

    International Nuclear Information System (INIS)

    Kamijo, H; Hata, H; Fujimoto, H; Inoue, A; Nagashima, K; Ikeda, K; Yamada, H; Sanuki, Y; Tomioka, A; Uwamori, K; Yoshida, S; Iwakuma, M; Funaki, K

    2006-01-01

    We designed a floor type single-phase 4 MVA superconducting traction transformer for Shinkansen rolling stock. In this study, we fabricated a prototype superconducting traction transformer based on this design. This transformer of the core-type design has a primary winding, four secondary windings and a tertiary winding. The windings are wound by Bi2223 superconducting tapes and cooled by subcooled liquid nitrogen. The core is kept at room temperature. The cryostat is made of GFRP with two holes to pass core legs through. The outer dimensions are about 1.2m x 0.7m x 1.9m excluding the compressor. Its weight is 1.71t excluding that of refrigerator and compressor. The transformer was tested according to Japanese Industrial Standards (JIS)-E5007. We confirmed that the performance of transformer has been achieved almost exactly as planned. The rated capacity is equivalent to 3.5MVA in the superconducting state

  3. Assessment of HAV and HEV Seroprevalence in Children Living in Post-Earthquake Camps from Duezce, Turkey

    International Nuclear Information System (INIS)

    Sencan, Irfan; Sahin, Idris; Kaya, Demet; Oksuz, Sukru; Yildirim, Mustafa

    2004-01-01

    The aim of the study was to investigate the prevalance of enterically transmitted hepatitis among children living in post-earthquake camps, and to assess the efficacy of the measurements during and after the disaster in Duezce and Golyaka. In the second half of 1999, North-western Turkey, was struck by two massive earthquakes in less than 3months. The first, on 17 August 1999, involving Golyaka, was struck, measuring between 7.4 and 7.8 on the Richter scale. Irregularity about providing clean water and necessary sanitary facilities were observed after the first earthquake because of confusion. The second quake, on 12 November 1999, which rated 7.2 on the Richter scale, shook Duezce. Necessary precautions were applied rapidly at the second quake about shelter, clean drinking water, food and control of distribution of the aids by government and civil aid organisations. Anti-HEV(IgG) and anti-HAV(IgG) antibodies were determined in 476 sera of the children who was living in six camps. HAV prevalence of the children who were living in Duezce and Golyaka temporary houses was 44.4 and 68.8% respectively, OR: 0.37, CI 95%: 0.22-0.61, p=0.0005. HEV prevalence of the children was 4.7 and 17.2% respectively, OR: 0.24, CI 95%: 0.11-0.51, p=0.0007. In conclusion, HAV and HEV prevalence of children were lower than that in endemic areas but higher than that in developed countries. This study has pointed out the importance of providing urgent need of the sufficient sanitary facilities after disasters for preventing or reducing the incidence of enterically transmitted hepatitis, especially in the regions which were at risk for various disasters. Essential precautions such as providing clean water and food supply must be taken and an emergency action plan for preventing the infectious disease must be prepared before disasters such as earthquakes

  4. Creation of electromechanical device for electric vehicle traction

    Directory of Open Access Journals (Sweden)

    Денис Юрьевич Зубенко

    2016-10-01

    Full Text Available The problems of creation of electromechanical device for electric vehicle traction are considered in the article. The aim of creation this design are the replacement of the internal combustion engine on electromechanical device. For this electromechanical device are constructed model, which describe processes that occur in the electric drive of electromechanical device. Characteristics of the main modes of motion were recorded. The introduction of electromechanical device will reduce the level of emissions and reduce noise in the cities

  5. REACTIVE POWER DEVICES IN SYSTEMS OF ELECTRIC TRACTION

    Directory of Open Access Journals (Sweden)

    M. O. Kostin

    2010-04-01

    Full Text Available A comparative characteristic of different concepts and expressions for determination of reactive power in the circuits with non-sinusoidal electric values has been given. For the first Ukrainian electric locomotives of DE1 type with the system of DC electric traction, the values of reactive power after Budeany, Fryze, and also the differential, integral and generalized reactive powers have been determined. Some measures on reducing its consumption by the DC electric rolling stock have been suggested.

  6. Rotor Design of IPMSM Traction Motor Based on Multi- Objective Optimization using BFGS Method and Train Motion Equations

    Directory of Open Access Journals (Sweden)

    S. Ahmadi

    2015-09-01

    Full Text Available In this paper a multiobjective optimal design method of interior permanent magnet synchronous motor ( IPMSM for traction applications so as to maximize average torque and to minimize torque ripple has been presented. Based on train motion equations and physical properties of train, desired specifications such as steady state speed, rated output power, acceleration time and rated speed of traction motor are related to each other. By considering the same output power, steady state speed, rated voltage, rated current and different acceleration time for a specified train, multiobjective optimal design has been performed by Broyden–Fletcher–Goldfarb–Shanno (BFGS method and finite element method (FEM has been chosen as an analysis tool. BFGS method is one of Quasi Newton methods and is counted in classic approaches. Classic optimization methods are appropriate when FEM is applied as an analysis tool and objective function isn’t expressed in closed form in terms of optimization variables.

  7. Use of microPCM fluids as enhanced liquid coolants in automotive EV and HEV vehicles. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mulligan, James C.; Gould, Richard D.

    2001-10-31

    Proof-of-concept experiments using a specific microPCM fluid that potentially can have an impact on the thermal management of automotive EV and HEV systems have been conducted. Samples of nominally 20-micron diameter microencapsulated octacosane and glycol/water coolant were prepared for testing. The melting/freezing characteristics of the fluid, as well as the viscosity, were determined. A bench scale pumped-loop thermal system was used to determine heat transfer coefficients and wall temperatures in the source heat exchanged. Comparisons were made which illustrate the enhancements of thermal performance, reductions of pumping power, and increases of heat transfer which occur with the microPCM fluid.

  8. Estimation of State of Charge of Lithium-Ion Batteries Used in HEV Using Robust Extended Kalman Filtering

    Directory of Open Access Journals (Sweden)

    Suleiman M. Sharkh

    2012-04-01

    Full Text Available A robust extended Kalman filter (EKF is proposed as a method for estimation of the state of charge (SOC of lithium-ion batteries used in hybrid electric vehicles (HEVs. An equivalent circuit model of the battery, including its electromotive force (EMF hysteresis characteristics and polarization characteristics is used. The effect of the robust EKF gain coefficient on SOC estimation is analyzed, and an optimized gain coefficient is determined to restrain battery terminal voltage from fluctuating. Experimental and simulation results are presented. SOC estimates using the standard EKF are compared with the proposed robust EKF algorithm to demonstrate the accuracy and precision of the latter for SOC estimation.

  9. Harmonic analysis of electric locomotive and traction power system based on wavelet singular entropy

    Science.gov (United States)

    Dun, Xiaohong

    2018-05-01

    With the rapid development of high-speed railway and heavy-haul transport, the locomotive and traction power system has become the main harmonic source of China's power grid. In response to this phenomenon, the system's power quality issues need timely monitoring, assessment and governance. Wavelet singular entropy is an organic combination of wavelet transform, singular value decomposition and information entropy theory, which combines the unique advantages of the three in signal processing: the time-frequency local characteristics of wavelet transform, singular value decomposition explores the basic modal characteristics of data, and information entropy quantifies the feature data. Based on the theory of singular value decomposition, the wavelet coefficient matrix after wavelet transform is decomposed into a series of singular values that can reflect the basic characteristics of the original coefficient matrix. Then the statistical properties of information entropy are used to analyze the uncertainty of the singular value set, so as to give a definite measurement of the complexity of the original signal. It can be said that wavelet entropy has a good application prospect in fault detection, classification and protection. The mat lab simulation shows that the use of wavelet singular entropy on the locomotive and traction power system harmonic analysis is effective.

  10. Traction cytometry: regularization in the Fourier approach and comparisons with finite element method.

    Science.gov (United States)

    Kulkarni, Ankur H; Ghosh, Prasenjit; Seetharaman, Ashwin; Kondaiah, Paturu; Gundiah, Namrata

    2018-05-09

    Traction forces exerted by adherent cells are quantified using displacements of embedded markers on polyacrylamide substrates due to cell contractility. Fourier Transform Traction Cytometry (FTTC) is widely used to calculate tractions but has inherent limitations due to errors in the displacement fields; these are mitigated through a regularization parameter (γ) in the Reg-FTTC method. An alternate finite element (FE) approach computes tractions on a domain using known boundary conditions. Robust verification and recovery studies are lacking but essential in assessing the accuracy and noise sensitivity of the traction solutions from the different methods. We implemented the L2 regularization method and defined a maximum curvature point in the traction with γ plot as the optimal regularization parameter (γ*) in the Reg-FTTC approach. Traction reconstructions using γ* yield accurate values of low and maximum tractions (Tmax) in the presence of up to 5% noise. Reg-FTTC is hence a clear improvement over the FTTC method but is inadequate to reconstruct low stresses such as those at nascent focal adhesions. FE, implemented using a node-by-node comparison, showed an intermediate reconstruction compared to Reg-FTTC. We performed experiments using mouse embryonic fibroblast (MEF) and compared results between these approaches. Tractions from FTTC and FE showed differences of ∼92% and 22% as compared to Reg-FTTC. Selection of an optimum value of γ for each cell reduced variability in the computed tractions as compared to using a single value of γ for all the MEF cells in this study.

  11. Improved motor intergrated permanent magnet gear for traction applications

    DEFF Research Database (Denmark)

    Frandsen, Tommy V.; Rasmussen, Peter Omand; Jensen, Karsten K.

    2012-01-01

    The Foster type electro-thermal RC network inside power semiconductor device is normally provided by manufacturers for junction temperature estimation. However it will result in inaccuracy or error when further attaching the Foster network with thermal impedances of heat sink or thermal grease, w...

  12. 3.0 T MR imaging of the ankle: Axial traction for morphological cartilage evaluation, quantitative T2 mapping and cartilage diffusion imaging—A preliminary study

    Energy Technology Data Exchange (ETDEWEB)

    Jungmann, Pia M., E-mail: pia.jungmann@tum.de [Department of Radiology, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Baum, Thomas, E-mail: thomas.baum@tum.de [Department of Radiology, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Schaeffeler, Christoph, E-mail: schaeffeler@me.com [Department of Radiology, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Musculoskeletal Imaging, Kantonsspital Graubuenden, Loestrasse 170, CH-7000 Chur (Switzerland); Sauerschnig, Martin, E-mail: martin.sauerschnig@mri.tum.de [Department of Trauma Surgery, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Department of Orthopaedic Sports Medicine, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Brucker, Peter U., E-mail: peter.brucker@lrz.tu-muenchen.de [Department of Orthopaedic Sports Medicine, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Mann, Alexander, E-mail: abmann@onlinemed.de [Department of Radiology, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Department of Orthopaedic Sports Medicine, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Ganter, Carl, E-mail: cganter@tum.de [Department of Radiology, Klinikum rechts der Isar, Technische Universitaet Muenchen, Ismaninger Strasse 22, 81675 Munich (Germany); Bieri, Oliver, E-mail: oliver.bieri@unibas.ch [Division of Radiological Physics, Department of Radiology, University of Basel Hospital, Petersgraben 4, 4031 Basel (Switzerland); and others

    2015-08-15

    Highlights: • Axial traction is applicable during high resolution MR imaging of the ankle. • Axial traction during MR imaging oft the ankle improves cartilage surface delineation of the individual tibial and talar cartilage layer for better morphological evaluation without the need of intraarticular contrast agent application. • Coronal T1-weighted MR images with a driven equilibrium pulse performed best. • Axial traction during MR imaging of the ankle facilitates compartment discrimination for segmentation purposes resulting in better reproducibility. - Abstract: Purpose: To determine the impact of axial traction during high resolution 3.0 T MR imaging of the ankle on morphological assessment of articular cartilage and quantitative cartilage imaging parameters. Materials and Methods: MR images of n = 25 asymptomatic ankles were acquired with and without axial traction (6 kg). Coronal and sagittal T1-weighted (w) turbo spin echo (TSE) sequences with a driven equilibrium pulse and sagittal fat-saturated intermediate-w (IMfs) TSE sequences were acquired for morphological evaluation on a four-point scale (1 = best, 4 = worst). For quantitative assessment of cartilage degradation segmentation was performed on 2D multislice-multiecho (MSME) SE T2, steady-state free-precession (SSFP; n = 8) T2 and SSFP diffusion-weighted imaging (DWI; n = 8) images. Wilcoxon-tests and paired t-tests were used for statistical analysis. Results: With axial traction, joint space width increased significantly and delineation of cartilage surfaces was rated superior (P < 0.05). Cartilage surfaces were best visualized on coronal T1-w images (P < 0.05). Differences for cartilage matrix evaluation were smaller. Subchondral bone evaluation, motion artifacts and image quality were not significantly different between the acquisition methods (P > 0.05). T2 values were lower at the tibia than at the talus (P < 0.001). Reproducibility was better for images with axial traction. Conclusion

  13. 3.0 T MR imaging of the ankle: Axial traction for morphological cartilage evaluation, quantitative T2 mapping and cartilage diffusion imaging—A preliminary study

    International Nuclear Information System (INIS)

    Jungmann, Pia M.; Baum, Thomas; Schaeffeler, Christoph; Sauerschnig, Martin; Brucker, Peter U.; Mann, Alexander; Ganter, Carl; Bieri, Oliver

    2015-01-01

    Highlights: • Axial traction is applicable during high resolution MR imaging of the ankle. • Axial traction during MR imaging oft the ankle improves cartilage surface delineation of the individual tibial and talar cartilage layer for better morphological evaluation without the need of intraarticular contrast agent application. • Coronal T1-weighted MR images with a driven equilibrium pulse performed best. • Axial traction during MR imaging of the ankle facilitates compartment discrimination for segmentation purposes resulting in better reproducibility. - Abstract: Purpose: To determine the impact of axial traction during high resolution 3.0 T MR imaging of the ankle on morphological assessment of articular cartilage and quantitative cartilage imaging parameters. Materials and Methods: MR images of n = 25 asymptomatic ankles were acquired with and without axial traction (6 kg). Coronal and sagittal T1-weighted (w) turbo spin echo (TSE) sequences with a driven equilibrium pulse and sagittal fat-saturated intermediate-w (IMfs) TSE sequences were acquired for morphological evaluation on a four-point scale (1 = best, 4 = worst). For quantitative assessment of cartilage degradation segmentation was performed on 2D multislice-multiecho (MSME) SE T2, steady-state free-precession (SSFP; n = 8) T2 and SSFP diffusion-weighted imaging (DWI; n = 8) images. Wilcoxon-tests and paired t-tests were used for statistical analysis. Results: With axial traction, joint space width increased significantly and delineation of cartilage surfaces was rated superior (P < 0.05). Cartilage surfaces were best visualized on coronal T1-w images (P < 0.05). Differences for cartilage matrix evaluation were smaller. Subchondral bone evaluation, motion artifacts and image quality were not significantly different between the acquisition methods (P > 0.05). T2 values were lower at the tibia than at the talus (P < 0.001). Reproducibility was better for images with axial traction. Conclusion

  14. The outcomes of pars plana vitrectomy without endotamponade for tractional retinal detachment secondary to proliferative diabetic retinopathy

    Directory of Open Access Journals (Sweden)

    Rao Muhammad Rashad Qamar

    2013-10-01

    Full Text Available AIM: To evaluate the outcomes of pars plana vitrectomy (PPV without the use of an ocular tamponade in patients having tractional retinal detachment (TRD secondary to proliferative diabetic retinopathy (PDR.METHODS: It was an interventional study conducted at the Department of Ophthalmology, B.V. Hospital, Bahawalpur, Pakistan, from July 2011 to July 2012. A total of 75 patients (84 eyes having TRD secondary to PDR were treated by PPV without using an ocular tamponade. All patients included in the study had a tractional retinal detachment secondary to proliferative diabetic retinopathy but didn’t have or develop retinal breaks before or during the study period. The surgical procedure included a PPV combined with the removal of the tractional retinal membranes and the application of endolaser photocoagulation to the retina. The mean follow-up period was 12 months.RESULTS:Successful retinal reattachement was observed in 78 of the operated eyes (92.8%. In these patients, the retina remained attached till the end of the one year follow-up period. Improvement in best corrected visual acuity (BCVA was seen in 63 eyes (75%. The visual acuity remained unchanged in 9 eyes (10.7%. Mean improvement in BCVA was 2.00+1.24 at baseline to 1.24+1.22 (PCONCLUSION: In the absence of the retinal breaks, a TRD secondary to PDR can be successfully treated by pars plana vitrectomy without the use of an ocular tamponade.

  15. Sustainability Aspects of Energy Conversion in Modern High-Speed Trains with Traction Induction Motors

    Directory of Open Access Journals (Sweden)

    Marc A. Rosen

    2015-03-01

    Full Text Available Some aspects are illustrated of energy conversion processes during the operation of electric railway vehicles with traction induction motors, in order to support transport systems’ sustainability. Increasing efforts are being expended to enhance the sustainability of transportation technologies and systems. Since electric drive systems are used with variable voltage variable frequency (VVVF inverters and traction induction motors, these machines with appropriate controls can realize both traction and electric braking regimes for electric traction vehicles. In line with this idea, this paper addresses the operation sustainability of electric railway vehicles highlighting the chain of interactions among the main electric equipment on an electrically driven railway system supplied from an a.c. contact line: The contact line-side converter, the machine-side converter and the traction induction motor. The paper supports the findings that electric traction drive systems using induction motors fed by network-side converters and VVVF inverters enhance the sustainable operation of railway trains.

  16. DEFINITION OF LOCOMOTIVE TRACTION FORCE WITH REGARD TO UNEVEN LOADING OF WHEEL-MOTOR BLOCK

    Directory of Open Access Journals (Sweden)

    B. Ye. Bodnar

    2013-11-01

    Full Text Available Purpose. The article describes the most common methods for determining the locomotive traction force. Solving the tasks of traction calculations involves determination of the forces influencing the train at every point of the way. When choosing a rational trajectory of the train motion and the development of operational regulations of train driving it is necessary to determine the actual value of the locomotive traction force. Considering various factors, power value of traction electric motor of locomotive may have significant differences. Advancement of the operational definition system of the locomotive traction force during the calculations by electrical parameters of traction electric motor with regard to uneven load of wheel-motor block is the purpose of the article. Methodology. The method of determining the traction force of locomotives and diesel locomotives with electric transmission, which is based on primary data acquisition of traction electric engines of direct current behavior, was proposed. Sensors and their integration into the electrical circuitry of the locomotive in order to get the data in digital form and for operational calculation of the each traction motor mode and the definition of locomotive traction force are presented. Findings. The experimental investigation of the system of locomotive traction force determination with the electric traction motor ED-105 was offered. A comparison of electrical and mechanical power of the electric motor was conducted. Originality. The system of locomotives power operational definition, which takes into account the variable electro-mechanical factors of wheel and motor blocks and increases the accuracy of the calculations, was proposed. Practical value. The system is a part of an onboard complex in definition of energy-efficient regimes for trains movement and provides the definition of accelerating and decelerating forces.

  17. Orthodontic traction of a transmigrated mandibular canine using mini-implant: a case report and review.

    Science.gov (United States)

    Plaza, Sonia Patricia

    2016-12-01

    The patient in this case is an 11-year-old girl, whose mandibular left canine was transmigrated. The traction to the arch was assisted by using a temporary skeletal anchorage device. After 5 months of poor response to traction, the biomechanics were re-adjusted, obtaining effective traction in to the arch in 12 months. After this period, the treatment was completed with fixed orthodontic appliances.

  18. Distributed active traction control system applied to the RoboCup middle size league

    OpenAIRE

    Almeida, José; Dias, André; Sequeira, João; Martins, Alfredo; Silva, Eduardo

    2013-01-01

    This work addresses the problem of traction control in mobile wheeled robots in the particular case of the RoboCup Middle Size League (MSL). The slip control problem is formulated using simple friction models for ISePorto Team robots with a differential wheel configuration. Traction was also characterized experimentally in the MSL scenario for relevant game events. This work proposes a hierarchical traction control architecture which relies in local slip detection and con...

  19. Structural analysis of the endogenous glycoallergen Hev b 2 (endo-β-1,3-glucanase) from Hevea brasiliensis and its recognition by human basophils

    Energy Technology Data Exchange (ETDEWEB)

    Rodríguez-Romero, Adela, E-mail: adela@unam.mx; Hernández-Santoyo, Alejandra; Fuentes-Silva, Deyanira [Universidad Nacional Autónoma de México, Circuito Exterior, CU, 04310 Coyoacán, DF (Mexico); Palomares, Laura A. [Universidad Nacional Autónoma de México, Apartado Postal 510-3, 62250 Cuernavaca, MOR (Mexico); Muñoz-Cruz, Samira; Yépez-Mulia, Lilian [Centro Médico Nacional Siglo XXI, IMSS, Avenida Cuauhtémoc 330, Colonia Doctores, Mexico, DF (Mexico); Orozco-Martínez, Socorro [Instituto Nacional de Pediatría, Insurgentes Sur 3700C, 04530 Cuicuilco, DF (Mexico); Universidad Nacional Autónoma de México, Circuito Exterior, CU, 04310 Coyoacán, DF (Mexico)

    2014-02-01

    This study describes the three-dimensional structure of the endogenous glycosylated allergen Hev b 2 (endo-β-1,3-glucanase), which exhibits three post-translational modifications that form a patch on the surface of the molecule that is proposed to be an allergenic IgE epitope. Endogenous glycosylated Hev b 2 (endo-β-1,3-glucanase) from Hevea brasiliensis is an important latex allergen that is recognized by IgE antibodies from patients who suffer from latex allergy. The carbohydrate moieties of Hev b 2 constitute a potentially important IgE-binding epitope that could be responsible for its cross-reactivity. Here, the structure of the endogenous isoform II of Hev b 2 that exhibits three post-translational modifications, including an N-terminal pyroglutamate and two glycosylation sites at Asn27 and at Asn314, is reported from two crystal polymorphs. These modifications form a patch on the surface of the molecule that is proposed to be one of the binding sites for IgE. A structure is also proposed for the most important N-glycan present in this protein as determined by digestion with specific enzymes. To analyze the role of the carbohydrate moieties in IgE antibody binding and in human basophil activation, the glycoallergen was enzymatically deglycosylated and evaluated. Time-lapse automated video microscopy of basophils stimulated with glycosylated Hev b 2 revealed basophil activation and degranulation. Immunological studies suggested that carbohydrates on Hev b 2 represent an allergenic IgE epitope. In addition, a dimer was found in each asymmetric unit that may reflect a regulatory mechanism of this plant defence protein.

  20. Effective Maxillary Protraction with Tandem Traction Bow Appliance

    Directory of Open Access Journals (Sweden)

    Pravin Kumar S Marure

    2014-01-01

    Full Text Available Tandem traction bow appliance (TTBA promotes patient compliance, because it is more esthetic and comfortable than extraoral appliances. TTBA should be used only in case where maxillary deficiency and normal mandible is present. Advantages of it includes good oral hygiene, early treatment of any Class III malocclusion, optimal retention, distribution of the forces for protraction to all maxillary teeth, free mandibular movement. It can be used in conjunction with fixed appliances if necessary. This paper includes two case reports. The treatment results in both the cases demonstrated significant skeletal and dental response to TTBA therapy. Skeletal change was primarily a result of anterior movement of the maxilla.

  1. Model-based efficiency evaluation of combine harvester traction drives

    Directory of Open Access Journals (Sweden)

    Steffen Häberle

    2015-08-01

    Full Text Available As part of the research the drive train of the combine harvesters is investigated in detail. The focus on load and power distribution, energy consumption and usage distribution are explicitly explored on two test machines. Based on the lessons learned during field operations, model-based studies of energy saving potential in the traction train of combine harvesters can now be quantified. Beyond that the virtual machine trial provides an opportunity to compare innovative drivetrain architectures and control solutions under reproducible conditions. As a result, an evaluation method is presented and generically used to draw comparisons under local representative operating conditions.

  2. Traction Control Study for a Scaled Automated Robotic Car

    OpenAIRE

    Morton, Mark A.

    2004-01-01

    This thesis presents the use of sliding mode control applied to a 1/10th scale robotic car to operate at a desired slip. Controlling the robot car at any desired slip has a direct relation to the amount of force that is applied to the driving wheels based on road surface conditions. For this model, the desired traction/slip is maintained for a specific surface which happens to be a Lego treadmill platform. How the platform evolved and the robot car was designed are also covered. To parame...

  3. Dual rotor single- stator axial air gap PMSM motor/generator drive for high torque vehicles applications

    International Nuclear Information System (INIS)

    University of Timisoara, Electrical Engineering Department, Vasile Parvan str., no. 1-2, 300223 Timisoara (Romania))" data-affiliation=" (Politehnica University of Timisoara, Electrical Engineering Department, Vasile Parvan str., no. 1-2, 300223 Timisoara (Romania))" >Tutelea, L N; University of Timisoara, Electrical Engineering Department, Vasile Parvan str., no. 1-2, 300223 Timisoara (Romania))" data-affiliation=" (Politehnica University of Timisoara, Electrical Engineering Department, Vasile Parvan str., no. 1-2, 300223 Timisoara (Romania))" >Boldea, I; University of Timisoara, Department of Electrotechnical Engineering and Industrial Informatics, 5 Revolution Street, Hunedoara, 331128 (Romania))" data-affiliation=" (Politehnica University of Timisoara, Department of Electrotechnical Engineering and Industrial Informatics, 5 Revolution Street, Hunedoara, 331128 (Romania))" >Deaconu, S I; University of Timisoara, Department of Electrotechnical Engineering and Industrial Informatics, 5 Revolution Street, Hunedoara, 331128 (Romania))" data-affiliation=" (Politehnica University of Timisoara, Department of Electrotechnical Engineering and Industrial Informatics, 5 Revolution Street, Hunedoara, 331128 (Romania))" >Popa, G N

    2014-01-01

    The actual e – continuously variable transmission (e-CVT) solution for the parallel Hybrid Electric Vehicle (HEV) requires two electric machines, two inverters, and a planetary gear. A distinct electric generator and a propulsion electric motor, both with full power converters, are typical for a series HEV. In an effort to simplify the planetary-geared e-CVT for the parallel HEV or the series HEV we hereby propose to replace the basically two electric machines and their two power converters by a single, axial-air-gap, electric machine central stator, fed from a single PWM converter with dual frequency voltage output and two independent PM rotors, destined for hybrid electric vehicles (HEV) and military vehicles applications. The proposed topologies and the magneto-motive force analysis are the core of the paper

  4. Dual rotor single- stator axial air gap PMSM motor/generator drive for high torque vehicles applications

    Science.gov (United States)

    Tutelea, L. N.; Deaconu, S. I.; Boldea, I.; Popa, G. N.

    2014-03-01

    The actual e - continuously variable transmission (e-CVT) solution for the parallel Hybrid Electric Vehicle (HEV) requires two electric machines, two inverters, and a planetary gear. A distinct electric generator and a propulsion electric motor, both with full power converters, are typical for a series HEV. In an effort to simplify the planetary-geared e-CVT for the parallel HEV or the series HEV we hereby propose to replace the basically two electric machines and their two power converters by a single, axial-air-gap, electric machine central stator, fed from a single PWM converter with dual frequency voltage output and two independent PM rotors, destined for hybrid electric vehicles (HEV) and military vehicles applications. The proposed topologies and the magneto-motive force analysis are the core of the paper.

  5. Traction-drive seven degrees-of-freedom telerobot arm: A concept for manipulation in space

    International Nuclear Information System (INIS)

    Kuban, D.P.; Williams, D.M.

    1987-01-01

    As man seeks to expand his dominion into new environments, the demand increases for machines that perform useful functions in remote locations. This new concept for manipulation in space is based on knowledge and experience gained from manipulator systems developed to meet the needs of remote nuclear applications. It merges the best characteristics of teleoperation and robotic technologies. This paper summarizes the report of a study performed for NASA Langley Research Center. The design goals for the telerobot, a mechanical description, and technology areas that must be addressed for successful implementation will be presented and discussed. The concept incorporates mechanical traction drives, redundant kinematics, and modular arm subelements to provide a backlash-free manipulator capable of obstacle avoidance. Further development of this arm is in progress at the Oak Ridge National Laboratory

  6. Traction calculation of band conveyors using the ''Nairi-2'' computer

    Energy Technology Data Exchange (ETDEWEB)

    Kutlunin, V A; Livshis, A V; Pod' yemshchikov, A N

    1982-01-01

    An algorithm is described and a program is introduced for traction calculation of band conveyors using the ''Nairi-2'' computer. The calculation system of the conveyor is derived by means of dividing the closed loop of the band into straight sections, which are separated by drums. The number of sections depends on the number of drums, the bypass system of them by the band, the shape of the conveyor route and in each specific case, a specific number is chosen. The initial information for the computer is assigned by a matrix, each row of which consists of parameters of the corresponding section. As a result, the forces of the beginning and end of the sections are found, and the required output of the drive motors with observance of the conditions of non-slippage of the drive drums and limiting of the maximum slack of the band between rollers are also found. The program allows one to make traction calculations of band conveyors with any routing shape for any number and position of the drive drums.

  7. MONITORING OF ELECTRICAL ENERGY QUALITY ON THE TRACTION SUBSTATION INPUT

    Directory of Open Access Journals (Sweden)

    O.G. Gryb

    2015-12-01

    Full Text Available For the implementation of measures to maintain the quality of the energy industrial enterprises have to spend a significant material and monetary assets. In this regard, significant is the feasibility study of the allocation of such funds and, primarily, the determination of the economic damage arising from low quality of electricity. The reliability of the electricity metering system, relay protection and automation of modern digital substations depends on the quality of electrical energy. At the present time to improve the reliability of the substation operation it is necessary to monitor indicators of quality of electric energy, allowing you to take organizational and technical solutions for their improvement. Monitoring the power quality at the input traction substation has shown that indicators such as the coefficient of the n-th harmonic component of the voltage does not meet the standards GOST 13109-97. The source of higher harmonics is a voltage Converter used on the locomotive. To eliminate higher harmonics in the supply network for traction substations will need to install power filters. Today, the USB-analyzer of power quality «Digital measurement system of power quality» type of CSICE of accuracy class 0.2. Work energy requires reliable and quality electricity supply to consumers. The new model of balancing energy market are bilateral contracts. The main task of this market, it ensure the stable and reliable operation of the unified energy system of Ukraine, that is, transmission and supply of electricity of appropriate quality.

  8. The improvement of maintenance service for traction networks equipment on the base of process approach

    Directory of Open Access Journals (Sweden)

    D. V. Mironov

    2014-12-01

    Full Text Available Purpose. The new methods development for improving the maintenance service for equipment of traction networks in order to increase its efficiency and quality. Methodology. In world practice of solving problems related to the quality of products and services is usually achieved by introducing quality management system in to the enterprises. The provisions of quality management system were used for solving the problem. The technologies of process engineering were used for describing the main stages of maintenance service. Findings. The development of high-speed movement and growth of its intensity, the use of electric rolling stock of a new generation require the introduction of new methods diagnostics of equipment technical state and improvement of the existing maintenance system and repair of power supply. Developing a model of business-processes, their optimization with using techniques of process engineering and system management is needed for the transition to the management system based on the process approach. From the standpoint of the process approach and in accordance with the requirements of the quality management system (ISO 9001-2009, the operation of the E (Department of electrification and power supply infrastructure sector is represented as a scheme of business-processes in which the guaranteed supply with electricity of railway and third-party consumers is defined as the main business-process of management. Each of the sub-process of power supply for consumers is described in details. The use methods and main stages of process approach for sample management system reorganization were investigated. The methodology and the application method of PDCA (Plan-Do-Check-Act closed loop to the equipment maintenance system were described. The monitoring process of traction networks maintenance using the process approach was divided into components after investigations. The technical documentation of maintenance service was investigated in

  9. Simulation-based design of a steerable acoustic warning device to increase (H)EV detectability while reducing urban noise pollution

    NARCIS (Netherlands)

    Van Genechten, B.; Berkhoff, Arthur P.

    2014-01-01

    This paper describes the simulation-based design methodology used in the eVADER project for the development of targeted acoustic warning devices for increased detectability of Hybrid and Electric Vehicles (HEVs) while, at the same time, reducing urban noise pollution compared to conventional

  10. Changes in dynamics processes of the muscles’ traction under influence of stress-factors

    Directory of Open Access Journals (Sweden)

    D. M. Nozdrenko

    2006-01-01

    Full Text Available Change of fibers’ dynamic parameters of the frog Rana temporaria skeletal muscle m. tibialis traction under influence of modulated stimulation and aluminium chloride solutions was studied. At 10-4,5·10-4 and 10‑3 M·l-1 concentrations of aluminium chloride the nonlinear decrease of the muscle fibers’ traction parameters was observed.

  11. Skull traction for cervical spinal injury in Enugu: A 5‑year ...

    African Journals Online (AJOL)

    Forty‑one had the American Spinal Injury Association (ASIA) Grade A whereas 64 had incomplete cord injury of ASIA Grades B–E. Forty‑eight had Crutchfield traction whereas 57 had Gardner‑Wells traction. At the end of treatment, no patient improved among those with ASIA Grades A and B. All the 12 cases of mortality ...

  12. Introducing the inbed spinal traction kit for use on patients with low ...

    African Journals Online (AJOL)

    BACKGROUND: Low backpain is a common malady in our environment. BODY: The in-bed spinal Traction kit is designed and assembled by the authors for use in treatment of Low Back Pain. The aim is to reduce cost, shorten period of Hospital stay and immobilization encountered when skin Traction Devices are used in ...

  13. The Harmonoise/IMAGINE model for traction noise of powered railway vehicles

    NARCIS (Netherlands)

    Dittrich, M.G.; Zhang, X.

    2006-01-01

    Traction noise is one of the noise sources of powered railway vehicles such as locomotives, electric- and diesel-powered multiple unit trains and high-speed trains. Especially at speeds below 60 km/h and at idling, but also at acceleration conditions for a wide range of speeds, traction noise can be

  14. Impedance-Based Harmonic Instability Assessment in Multiple Electric Trains and Traction Network Interaction System

    DEFF Research Database (Denmark)

    Tao, Haidong; Hu, Haitao; Wang, Xiongfei

    2018-01-01

    This paper presents an impedance-based method to systematically investigate the interaction between multi-train and traction networks, focusing on evaluating the harmonic instability problems. Firstly, the interaction mechanism of multi-train and the traction network is represented as a feedback ...

  15. Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

    Science.gov (United States)

    Cikanek, Susan R.

    1994-01-01

    An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control.

  16. Fuzzy logic electric vehicle regenerative antiskid braking and traction control system

    Science.gov (United States)

    Cikanek, S.R.

    1994-10-25

    An regenerative antiskid braking and traction control system using fuzzy logic for an electric or hybrid vehicle having a regenerative braking system operatively connected to an electric traction motor, and a separate hydraulic braking system includes sensors for monitoring present vehicle parameters and a processor, responsive to the sensors, for calculating vehicle parameters defining the vehicle behavior not directly measurable by the sensor and determining if regenerative antiskid braking control, requiring hydraulic braking control, and requiring traction control are required. The processor then employs fuzzy logic based on the determined vehicle state and provides command signals to a motor controller to control operation of the electric traction motor and to the brake controller to control fluid pressure applied at each vehicle wheel to provide the appropriate regenerative braking control, hydraulic braking control, and traction control. 123 figs.

  17. The role played by the Coulombic traction for an interface crack in dissimilar piezoelectric materials

    International Nuclear Information System (INIS)

    Li Qun; Chen Yiheng

    2008-01-01

    The role played by the Coulombic traction for an interface crack in dissimilar piezoelectric materials is clarified. Based on the extended Stroh theory, the Coulombic traction, usually neglected in piezoelectric fracture, is imposed on the interface crack surfaces. It is found that the low-capacitance medium (air or vacuum) inside the crack gap yields some large Coulombic traction as compared to the applied mechanical loading whether the remanent polarization of piezoelectric material is considered or not. Thus, previous investigations based on the traction-free condition underestimate the role of the Coulombic traction and in turn may yield unexpected errors for the effective stress intensity factor (SIF) and energy release rate (ERR) at the crack tip. (technical note)

  18. Syntegra: complete integration of traction, bogie and brake systems

    Energy Technology Data Exchange (ETDEWEB)

    Loewenstein, L.; Wangelin, F. von [Siemens AG, Transportation Systems, Erlangen (Germany). Group Technology TS GT; Teichmann, M.; Hoffmann, T. [Siemens TS, Graz (Austria); Joeckel, A. [Siemens Automation and Drives, Nuernberg (Germany)

    2007-07-01

    With Syntegra {sup registered} technology, Siemens has developed an approach to the complete integration of traction, bogie and brake systems, and this has initially been put into practice for metro, underground and S-Bahn (urban regional express) trains. Syntegra constitutes a fundamentally new approach, achieving a greater intensity of integration compared with the types of drive system that have been in use up until now. With Syntegra, the bogie, transmission and brake components are all brought together as part of one and the same system. The integration and, more especially, the technological advances within the three named areas bring about numerous synergies. The new generation of powered bogie features a combination of high efficiency, low dead weight and reduced emissions. A Syntegra drive system achieves a performance which is markedly better than that of conventional systems. (orig.)

  19. Traction control of an electric vehicle based on nonlinear observers

    Directory of Open Access Journals (Sweden)

    Diego A. Aligia

    2017-12-01

    Full Text Available A traction control strategy for a four-wheel electric vehicle is proposed in this paper. The strategy is based on nonlinear observers which allows estimating the maximum force that can be transmitted to the road. Knowledge of the maximum force allows controlling the slip of the driving wheels, preventing the wheel’s slippage in low-grip surfaces. The proposed strategy also allows to avoid the undesired yaw moment in the vehicle which occurs when road conditions on either side of it are dierent. This improves the eciency and the control of the vehicle, avoiding possible losses of stability that can result in risks for its occupants. Both the proposed observer and the control strategy are designed based on a dynamic rotational model of the wheel and a brush force model. Simulation results are obtained based on a complete vehicle model on the Simulink/CarSim platform.

  20. Traction for low back pain with or without sciatica: an updated systematic review within the framework of the Cochrane collaboration

    NARCIS (Netherlands)

    Clarke, J.; van Tulder, M.; Blomberg, S; de Vet, H.C.W.; van der Heijden, G; Bronfort, G.

    2006-01-01

    STUDY DESIGN. Systematic review. OBJECTIVE. To determine if traction is more effective than reference treatments, placebo/sham traction, or no treatment for low back pain (LBP). SUMMARY OF BACKGROUND DATA. Various types of traction are used in the treatment of LBP, often in conjunction with other

  1. Modeling of traction-coupling properties of wheel propulsor

    Science.gov (United States)

    Sakhapov, R. L.; Nikolaeva, R. V.; Gatiyatullin, M. H.; Makhmutov, M. M.

    2017-12-01

    In conditions of operation of aggregates on soils with low bearing capacity, the main performance indicators of their operation are determined by the properties of retaining the functional qualities of the propulsor. Therefore, the parameters of the anti-skid device can not be calculated by only one criterion. The equipment of propellers with anti-skid devices, which allow to reduce the compaction effect of the propulsion device on the soil, seems to be a rational solution to the problem of increasing traction and coupling properties of the driving wheels. The mathematical model is based on the study of the interaction of the driving wheel with anti-skid devices and a deformable bearing surface, which takes into account the wheel diameter, skid coefficient, the parameters of the anti-skid device, the physical and mechanical properties of the soil. As a basic mathematical model that determines the dependence of the coupling properties on the wheel parameters, the model obtained as a result of integration and reflecting the process of soil deformation from the shear stress is adopted. The total value of the resistance forces will determine the force of the hitch pressure on the horizontal soil layers, and the value of its deformation is the degree of wheel slippage. When the anti-skid devices interact with the soil, the traction capacity of the wheel is composed of shear forces, soil shear and soil deformation forces with detachable hooks. As a result of the interaction of the hook with the soil, the latter presses against the walls of the hook with the force equal to the sum of the hook load and the resistance to movement. During operation, the linear dimensions of the hook will decrease, which is not taken into account by the safety factor. Abrasive wear of the thickness of the hook is approximately proportional to the work of friction caused by the movement of the hook when inserted into the soil and slipping the wheel.

  2. Simulation of Induction Traction Drive with Supercapacitor Energy Storage System Test Bench

    Directory of Open Access Journals (Sweden)

    Stana Girts

    2015-12-01

    Full Text Available The paper describes the application of supercapacitor energy storage system for induction traction drive test bench that replaces a real electric public transport for performing testing and researches. The suitability and usage of such bench for research purposes is explained and the importance of the development of software mathematical model for performing simulations to be done before physical implementation measures is reasoned. The working principle of the bench and applied components are described. A virtual model of the bench was built and simulations were performed using Matlab/Simulink software. The basic topology of the virtual bench model is described as well. The calculations of this work show the scaling of supercapacitor energy storage system by setting different limits of working voltage range in order to adjust them to test bench parameters, whereas the modelling compares two simulation cases – the application of less supercapacitors and the application of more supercapacitors with the same common rated voltage. The autonomous mode simulations were also performed. Simulation results are analyzed and recommendations for the application of the supercapacitor energy storage system, with respect to initial supercapacitor circuit voltage, are given.

  3. Local traction force in the proximal leading process triggers nuclear translocation during neuronal migration.

    Science.gov (United States)

    Umeshima, Hiroki; Nomura, Ken-Ichi; Yoshikawa, Shuhei; Hörning, Marcel; Tanaka, Motomu; Sakuma, Shinya; Arai, Fumihito; Kaneko, Makoto; Kengaku, Mineko

    2018-04-05

    Somal translocation in long bipolar neurons is regulated by actomyosin contractile forces, yet the precise spatiotemporal sites of force generation are unknown. Here we investigate the force dynamics generated during somal translocation using traction force microscopy. Neurons with a short leading process generated a traction force in the growth cone and counteracting forces in the leading and trailing processes. In contrast, neurons with a long leading process generated a force dipole with opposing traction forces in the proximal leading process during nuclear translocation. Transient accumulation of actin filaments was observed at the dipole center of the two opposing forces, which was abolished by inhibition of myosin II activity. A swelling in the leading process emerged and generated a traction force that pulled the nucleus when nuclear translocation was physically hampered. The traction force in the leading process swelling was uncoupled from somal translocation in neurons expressing a dominant negative mutant of the KASH protein, which disrupts the interaction between cytoskeletal components and the nuclear envelope. Our results suggest that the leading process is the site of generation of actomyosin-dependent traction force in long bipolar neurons, and that the traction force is transmitted to the nucleus via KASH proteins. Copyright © 2018 Elsevier B.V. and Japan Neuroscience Society. All rights reserved.

  4. Traction bronchiectasis in cryptogenic fibrosing alveolitis: associated computed tomographic features and physiological significance

    Energy Technology Data Exchange (ETDEWEB)

    Desai, Sujal R. [Department of Radiology, King' s College Hospital, Denmark Hill, SE5 9RS, London (United Kingdom); Wells, Athol U.; Bois, Roland M. du [Interstitial Lung Disease Unit, Royal Brompton Hospital, Emmanuel Kaye Building, Manresa Road, Fulham, SW6 6LR, London (United Kingdom); Rubens, Michael B.; Hansell, David M. [Department of Radiology, Royal Brompton Hospital, Sydney Street, SW3 6NP, London (United Kingdom)

    2003-08-01

    Our objective was to evaluate the associated CT features and physiological consequences of traction bronchiectasis in patients with cryptogenic fibrosing alveolitis (CFA). The CT scans of 212 patients with CFA (158 men, 54 women; mean age 62.2{+-}10.6 years) were evaluated independently by two observers. The extent of fibrosis, the proportions of a reticular pattern and ground-glass opacification and the extent of emphysema were scored at five levels. The predominant CT pattern, coarseness of a reticular pattern and severity of traction bronchiectasis were graded semiquantitatively. Physiological indices were correlated with CT features. There was traction bronchiectasis on CT in 202 of 212 (95%) patients. Increasingly severe traction bronchiectasis was independently associated with increasingly extensive CFA (p<0.0005), a coarser reticular pattern (p<0.001), a lower proportion of ground-glass opacification (p<0.005) and less extensive emphysema (p<0.0005). Increasingly severe traction bronchiectasis was independently related to depression of DL{sub CO} (p<0.005), FVC (p=0.02) and pO{sub 2} (p<0.0005), but not indices of air-flow obstruction. In CFA, traction bronchiectasis increases with more extensive disease, a lower proportion of ground-glass opacification and a coarser reticular pattern, but it decreases with concurrent emphysema. Increasingly severe traction bronchiectasis is associated with additional physiological impairment for a given extent of pulmonary fibrosis and emphysema. (orig.)

  5. CALCULATION OF A MECHANICAL CHARACTERISTIC OF ELECTRIC TRACTION MOTOR OF ELECTRIC VEHICLE

    Directory of Open Access Journals (Sweden)

    Phuong Le Ngo

    2017-01-01

    Full Text Available The traction characteristic of an electric vehicle is the main characteristic of mechanical system that reflects its key performance indicators. Implementation of the traction characteristic is based on controlling angular speed and torque of electric traction motor in an automatic control system. The static mechanical characteristic of an electric traction motor in an automatic control system is the most important characteristic that determines weight, size and operating characteristics of an electric traction motor and serves as the basis for design. The most common variants of constructive implementation of a traction electric drive are analyzed, and a scheme is chosen for further design. Lagrange’s equation for electric mechanical system with one degree of freedom is written in generalized coordinates. In order to determine the generalized forces, elementary operation of all moments influencing on a moving car has been calculated. The resulting equation of motion of the electric vehicle corresponding to the design scheme, as well as the expressions for calculation of characteristic points of static mechanical characteristics of traction motor (i.e. the maximum and minimum time, minimum power are obtained. In order to determine the nominal values of the angular velocity and the power of electric traction motor, a method based on ensuring the movement of the vehicle in the standard cycle has been developed. The method makes it possible to calculate characteristic points of the mechanical characteristic with the lowest possible power rating. The algorithm for calculation of mechanical characteristics of the motor is presented. The method was applied to calculate static mechanical characteristic of an electric traction motor for a small urban electric truck.

  6. Surgical management of retinal diseases: proliferative diabetic retinopathy and traction retinal detachment.

    Science.gov (United States)

    Cruz-Iñigo, Yousef J; Acabá, Luis A; Berrocal, Maria H

    2014-01-01

    Current indications for pars plana vitrectomy in patients with proliferative diabetic retinopathy (PDR) include vitreous hemorrhage, tractional retinal detachment (TRD), combined tractional and rhegmatogenous retinal detachment (CTRRD), diabetic macular edema associated with posterior hyaloidal traction, and anterior segment neovascularization with media opacities. This chapter will review the indications, surgical objectives, adjunctive pharmacotherapy, microincision surgical techniques, and outcomes of diabetic vitrectomy for PDR, TRD, and CTRRD. With the availability of new microincision vitrectomy technology, wide-angle microscope viewing systems, and pharmacologic agents, vitrectomy can improve visual acuity and achieve long-term anatomic stability in eyes with severe complications from PDR. © 2014 S. Karger AG, Basel

  7. CT imaging techniques for describing motions of the cervicothoracic junction and cervical spine during flexion, extension, and cervical traction.

    Science.gov (United States)

    Simon, Scott; Davis, Martin; Odhner, Dewey; Udupa, Jayaram; Winkelstein, Beth

    2006-01-01

    Computerized tomographic study of human cadavers undergoing traction and flexion-extension bending. To investigate the feasibility of using computerized tomography techniques to quantify relative vertebral motions of the cervical spine and cervicothoracic junction (CTJ), and to define normative CTJ kinematics. Despite developing an understanding of the mechanical behavior of the cervical spine, little remains known about the cervicothoracic junction. The CTJ is more difficult to image than other cervical regions given the anatomic features of the surrounding bones obstructing CTJ visualization. As such, limited data have been reported describing the responses of the CTJ for motions and loading in the sagittal plane, confounding the clinical assessment of its injuries and surgical treatments used at this region. Helical CT images of the cervical spine and CTJ were acquired incrementally during each of flexion, extension, and cervical traction. Vertebral surfaces were reconstructed using the specialized image analysis software, 3DVIEWNIX. A mathematical description of relative vertebral motions was derived by computing rigid transformations. Euler angles and translations were calculated. Regional spine stiffness was defined for traction. The CTJ was found to be much stiffer (779 N/mm) than the cervical spine (317 N/mm) in tension. In flexion-extension bending, the CTJ was similar to the lower cervical spine. The CTJ demonstrated significantly less coupled motion than the cervical spine. The CTJ, as a transition region between the cervical and thoracic spines, has unique kinematic characteristics. This application of kinematic CT methods is useful for quantifying unreported normative ranges of motion for the CTJ, difficult by other conventional radiologic means.

  8. Dynamics of indicators of a metabolic exchange and condition of blood circulation of the bottom extremities after traction extension at patients with lumbar and sacral dorsopathy

    Directory of Open Access Journals (Sweden)

    Kotenko К.V.

    2013-12-01

    Full Text Available Aim: to study influence of traction therapy in a pulse mode in a complex with electrotherapy on a condition of blood circulation of the bottom extremities and level of a metabolic exchange. Material and methods. There had been examined 120 patients with a lumbar and sacral dorsopathy aged from 22 to 69 years (middle age of 49,5 years with prescription of a disease from 1 to 5 years, among them men of 34,2%, women of 65,8%. Results. The analysis of effects of various medical methods on a condition of local blood circulation in the bottom extremities showed that the most expressed its compensation is noted at complex application of mechanical pulse traction influence and electrotherapy for patients with a dorsopathy of lumbar and sacral department of a backbone that is confirmed by restoration to normal values of all indicators rheovasogramm. Conclusion. High clinical results of application of the combined medical and rehabilitation complex are based on compensation of local blood circulation that is shown in elimination of deficiency of blood supply due to improvement of a tone of arterial vessels and elimination of venous stagnation, and also due to increase of linear speed of a blood-groove and development of collateral blood circulation. Application of electrical impulse and mechanical traction influences, more at their combination promotes fermentative activity of the systems responsible for a protein exchange that is important for prevention of degenerate and dystrophic process progressing.

  9. A novel anchorage technique for transnasal traction in rigid external maxillary distraction.

    Science.gov (United States)

    Varol, A; Basa, S

    2013-12-01

    We describe an effective technique for anchorage of transnasal traction in the management of maxillary rotation during external distraction. Copyright © 2012 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  10. Basilar impression in osteogenesis imperfecta: can it be treated with halo traction and posterior fusion?

    NARCIS (Netherlands)

    Noske, D. P.; van Royen, B. J.; Bron, J. L.; Vandertop, W. P.

    2006-01-01

    Basilar impression (BI) and hydrocephalus complicating osteogenesis imperfecta (OI) is usually treated by anterior transoral decompression and posterior fixation. Nevertheless, it may be questioned if posterior fusion following axial halo traction is adequate in patients with symptomatic BI

  11. Performance Analysis of Permanent Magnet Motors for Electric Vehicles (EV Traction Considering Driving Cycles

    Directory of Open Access Journals (Sweden)

    Thanh Anh Huynh

    2018-05-01

    Full Text Available This paper evaluates the electromagnetic and thermal performance of several traction motors for electric vehicles (EVs. Two different driving cycles are employed for the evaluation of the motors, one for urban and the other for highway driving. The electromagnetic performance to be assessed includes maximum motor torque output for vehicle acceleration and the flux weakening capability for wide operating range under current and voltage limits. Thermal analysis is performed to evaluate the health status of the magnets and windings for the prescribed driving cycles. Two types of traction motors are investigated: two interior permanent magnet motors and one permanent magnet-assisted synchronous reluctance motor. The analysis results demonstrate the benefits and disadvantages of these motors for EV traction and provide suggestions for traction motor design. Finally, experiments are conducted to validate the analysis.

  12. Efficient Propulsion Structure with an Axial Flux Rotary Converter for HEV Drive Unit

    Directory of Open Access Journals (Sweden)

    Ales Havel

    2011-01-01

    Full Text Available This paper describes an efficient axial flux arrangement of the four quadrant rotary converter for hybrid electric vehicles. The design of the axial flux wound stator and both axial flux squirrel cage rotors is based on the arrangement of radial air gap induction motor and permanent magnet synchronous motor. The method of constant magnetic circuit volume is utilized for dimensions conversion, which results into basic dimensions of stator and rotor discs in axial flux conception. This allows the creation of real 3D models in the CAD application. Finally, the finite element simulations of electromagnetic induction in the axial flux stator pack are presented in the concluding part of this paper.

  13. Traction suture modification to tongue-in-groove caudal septoplasty.

    Science.gov (United States)

    Indeyeva, Y A; Lee, T S; Gordin, E; Chan, D; Ducic, Y

    2018-02-01

    Caudal septal deviation leads to unfavorable esthetic as well as functional effects on the nasal airway. A modification to the tongue-in-groove (TIG) technique to correct these caudal septal deformities is described. With placement of a temporary suspension suture to the caudal septum, manual traction is applied, assuring that the caudal septum remains in the midline position while it is being secured with multiple through-and-through, trans-columellar and trans-septal sutures. From 2003 to 2016, 148 patients underwent endonasal septoplasty using this modified technique, with excellent functional and cosmetic outcomes and a revision rate of 1.4%. This modified TIG technique replaces the periosteal suture that secures the caudal septum to the midline nasal crest in the original TIG technique. This simplifies the procedure and minimizes the risk of securing the caudal septum off-midline when used in endonasal septoplasty. Copyright © 2017 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  14. Sustainability Aspects of Energy Conversion in Modern High-Speed Trains with Traction Induction Motors

    OpenAIRE

    Marc A. Rosen; Doru A. Nicola; Cornelia A. Bulucea; Daniel C. Cismaru

    2015-01-01

    Some aspects are illustrated of energy conversion processes during the operation of electric railway vehicles with traction induction motors, in order to support transport systems’ sustainability. Increasing efforts are being expended to enhance the sustainability of transportation technologies and systems. Since electric drive systems are used with variable voltage variable frequency (VVVF) inverters and traction induction motors, these machines with appropriate controls can realize both tra...

  15. Observer Based Traction/Braking Control Design for High Speed Trains Considering Adhesion Nonlinearity

    OpenAIRE

    Cai, Wenchuan; Liao, Wenhao; Li, Danyong; Song, Yongduan

    2014-01-01

    Train traction/braking control, one of the key enabling technologies for automatic train operation, literally takes its action through adhesion force. However, adhesion coefficient of high speed train (HST) is uncertain in general because it varies with wheel-rail surface condition and running speed; thus, it is extremely difficult to be measured, which makes traction/braking control design and implementation of HSTs greatly challenging. In this work, force observers are applied to estimate t...

  16. Group traction drive as means to increase energy efficiency of lokomotives of open-pit transport

    Science.gov (United States)

    Antipin, D. Ya; Izmerov, O. V.; Bishutin, S. G.; Kobishchanov, V. V.

    2017-10-01

    Questions of possible use of a group drive for locomotives of an open-pit transport are considered. The possibility of a significant reduction of traction costs in the case of a combination of a group traction drive with devices for the non-inertial regulation of the coefficient of friction between the wheel and the rail has been shown, and new patentable solutions have been proposed.

  17. Measurement of the traction force of biological cells by digital holography

    Science.gov (United States)

    Yu, Xiao; Cross, Michael; Liu, Changgeng; Clark, David C.; Haynie, Donald T.; Kim, Myung K.

    2011-01-01

    The traction force produced by biological cells has been visualized as distortions in flexible substrata. We have utilized quantitative phase microscopy by digital holography (DH-QPM) to study the wrinkling of a silicone rubber film by motile fibroblasts. Surface deformation and the cellular traction force have been measured from phase profiles in a direct and straightforward manner. DH-QPM is shown to provide highly efficient and versatile means for quantitatively analyzing cellular motility. PMID:22254175

  18. A Study of Torque Vectoring and Traction Control for an All-Wheel Drive Electric Vehicle

    Directory of Open Access Journals (Sweden)

    Maharun Mui’nuddin

    2014-07-01

    Full Text Available Common vehicle always experience energy loss during cornering manoeuver. Thus, to ensure it did not happened especially at high speed, a study of torque vectoring and traction control need to be made since it can increase the traction control of tyres during cornering at high speed. The study of torque vectoring and traction control for an all-wheel drive electric vehicle was conducted by modelling an all-wheel drive electric vehicle (EV in ADAMS/Car software. In addition, an optimal control algorithm will be developed for best performance to minimize energy losses using MATLAB/Simulink software. Furthermore, to prove the effectiveness of the all-wheel drive electric, the torque and traction control simulation of the all-wheel drive electric vehicle will be compared with uncontrolled electric vehicle model. According to the result, torque vectoring and traction control of in-wheel motor in all wheel drive EV can help to increase the performance of the electric vehicle during cornering manoeuver. In conclusion, this study of torque vectoring and traction control for an all-wheel drive electric vehicle will help researchers to improve the design of the future electric vehicle in term of the vehicle performance during cornering manoeuvre.

  19. Acetabular labral tears: contrast-enhanced MR imaging under continuous leg traction

    Energy Technology Data Exchange (ETDEWEB)

    Nishii, T. [Div. of Functional Diagnostic Imaging, Biomedical Research Center, Osaka Univ. Medical School, Suita (Japan); Nakanishi, K. [Dept. of Radiology, Osaka Univ. Medical School, Suita (Japan); Sugano, N. [Dept. of Orthopaedic Surgery, Osaka Univ. Medical School, Suita (Japan); Naito, H. [Div. of Functional Diagnostic Imaging, Biomedical Research Center, Osaka Univ. Medical School, Suita (Japan); Tamura, S. [Div. of Functional Diagnostic Imaging, Biomedical Research Center, Osaka Univ. Medical School, Suita (Japan); Ochi, T. [Dept. of Orthopaedic Surgery, Osaka Univ. Medical School, Suita (Japan)

    1996-05-01

    The objective of this study was to evaluate the effects of continuous leg traction on contrast-enhanced MR imaging of the hip joint and to determine whether MR imaging under these conditions is useful for demonstrating acetabular labral tears. Nineteen hips underwent MR imaging with a T1-weighted spin-echo sequence, followed by MR imaging under continuous leg traction after intravenous injection of gadolinium-DTPA. Joint fluid enhancement and labral contour detection were evaluated. Eleven hips had labral tears shown by conventional arthrography, arthroscopy and macroscopic surgical findings. Assessment of labral tears by MR imaging was correlated with the diagnosis based on these standard techniques. Joint fluid enhancement was obtained in all hips at 30 min after injection. Superior and inferior labral surfaces were completely delineated in 1 hip on the unenhanced MR images, and in 7 and 13 hips, respectively, on the enhanced images under traction. The enhanced images under traction depicted 9 of the 11 labral tears. Comparison between the unenhanced image and the enhanced image under traction avoided mistaking undercutting of the labrum for a tear in 4 hips. Contrast-enhanced MR imaging under traction was valuable for detecting labral tears non-invasively and without radiation. Follow-up examinations using this method in patients with acetabular dysplasia can help to clarify the natural course of labral disorders and enable better treatment planning. (orig./MG)

  20. Traction bronchiectasis in cryptogenic fibrosing alveolitis: associated computed tomographic features and physiological significance

    International Nuclear Information System (INIS)

    Desai, Sujal R.; Wells, Athol U.; Bois, Roland M. du; Rubens, Michael B.; Hansell, David M.

    2003-01-01

    Our objective was to evaluate the associated CT features and physiological consequences of traction bronchiectasis in patients with cryptogenic fibrosing alveolitis (CFA). The CT scans of 212 patients with CFA (158 men, 54 women; mean age 62.2±10.6 years) were evaluated independently by two observers. The extent of fibrosis, the proportions of a reticular pattern and ground-glass opacification and the extent of emphysema were scored at five levels. The predominant CT pattern, coarseness of a reticular pattern and severity of traction bronchiectasis were graded semiquantitatively. Physiological indices were correlated with CT features. There was traction bronchiectasis on CT in 202 of 212 (95%) patients. Increasingly severe traction bronchiectasis was independently associated with increasingly extensive CFA (p CO (p 2 (p<0.0005), but not indices of air-flow obstruction. In CFA, traction bronchiectasis increases with more extensive disease, a lower proportion of ground-glass opacification and a coarser reticular pattern, but it decreases with concurrent emphysema. Increasingly severe traction bronchiectasis is associated with additional physiological impairment for a given extent of pulmonary fibrosis and emphysema. (orig.)

  1. Young adult patient with two palatally maxillary impacted canines and forced traction on rigid arches of stabilization. Case report.

    Science.gov (United States)

    Mucedero, M; Pezzuto, C; Rozzi, M; Ricchiuti, M R; Cozza, P

    2016-01-01

    Young adult patient treated for impaction of two maxillary canines. C.S., 15 years, female. Diagnostic evaluation by clinical and radiographic examinations shows permanent dentition with persistence of 5.3 and 6.3, impaction of 1.3 and 2.3, dento-skeletal Cl I malocclusion, normodivergence of bone bases. Analysis of TC dentalscan confirms the palatal impaction of 1.3 and 2.3. The treatment plan provided an orthodontic-surgical approach for adequate space management in dental arch, evaluation of eruption movements, choice of anchorage device, surgical exposure and application of the brackets. Deciduous canines have been extracted and an edgewise appliance with rigid rectangular full thickness archwires has been used to align the arches and to obtain maximum anchorage during the forced traction. The surgical phase, for exposure of 1.3 and 2.3 respectively, performed an open technique by excisional uncovering and a close technique by a repositioned flap. The case has been finalized for the achievement of the right occlusal keys. The possibility to choose the surgical technique depending on the intraosseous position of impacted teeth in association to the edgewise therapy with full thickness arches allows to realize an effectiveness surgical-orthodontic approach for the forced traction of impacted teeth in a favourable position.

  2. Single-Electrical-Port Control of Cascaded Doubly-Fed Induction Machine for EV/HEV Applications

    DEFF Research Database (Denmark)

    Han, Peng; Cheng, Ming; Chen, Zhe

    2017-01-01

    A single-electrical-port control scheme, for four-quadrant operation of cascaded doubly-fed induction machine (CDFIM), which has long been conceived as a motor or generator only suitable for limited two-quadrant operation, is proposed and theoretically demonstrated. The drive system is configured...... as slave inverter. With this configuration, the control emphasis is placed on the slave inverter, yielding reduced control complexity and cost, and the inaccuracy of flux estimation in conventional FOC for singly-fed induction machines is avoided at very low or even zero speed. It is found that the doubly...

  3. The impact of the neurodevelopmental traction technique on activation of lateral abdominal muscles in children aged 11-13 years.

    Science.gov (United States)

    Gogola, Anna; Gnat, Rafał; Dziub, Dorota; Gwóźdź, Michalina; Zaborowska, Małgorzata

    2016-06-27

    The aim of the study was to evaluate the activation of lateral abdominal muscles (LAM) in response to neurodevelopmental traction technique as assessed by ultrasounds as well as to compare the effects of different traction forces. An experiment with repeated measurements of the dependent variables was conducted. Thirty-seven children (22 girls) participated. Measurements of LAM thickness (indicating LAM activation) were performed bilaterally during traction of 5% body weight: 1) in neutral position, 2) in 20° posterior trunk inclination; during traction of 15% body weight: 3) in neutral position, 4) in 20° posterior trunk inclination. The ultrasound technology was employed. When applying the lighter traction the superficial LAM (external and internal oblique muscles) showed significant changes. The mean thickness of both muscles during traction increased (both p  0.05). Stronger traction elicited smaller changes. External and internal oblique muscles showed significant increases (p stronger traction (p Stronger traction induces smaller LAM thickness changes than lighter traction.

  4. Wrist Traction During MR Arthrography Improves Detection of Triangular Fibrocartilage Complex and Intrinsic Ligament Tears and Visibility of Articular Cartilage.

    Science.gov (United States)

    Lee, Ryan K L; Griffith, James F; Ng, Alex W H; Nung, Ryan C H; Yeung, David K W

    2016-01-01

    The purpose of this study was to assess the effects of traction during MR arthrography of the wrist on joint space widening, cartilage visibility, and detection of tears of the triangular fibrocartilage complex (TFCC) and intrinsic ligaments. A prospective study included 40 wrists in 39 patients (25 men, 14 women; mean age, 35 years). MR arthrography was performed with a 3-T MRI system with and without axial traction. Two radiologists independently measured wrist and carpal joint space widths and semiquantitatively graded articular cartilage visibility. Using conventional arthrography as the reference standard and working in consensus, they assessed for the presence of tears of the TFCC, lunotriquetral ligament (LTL), and scapholunate ligament (SLL). Visibility of a tear before traction was compared with visibility after traction. With traction, all joint spaces in the wrist and carpus were significantly widened (change, 0.15-1.01 mm; all p < 0.006). Subjective cartilage visibility of all joint spaces improved after traction (all p ≤ 0.048) except for that of the radioscaphoid space, which was well visualized even before traction. Conventional arthrography depicted 24 TFCC tears, seven LTL tears, and three SLL tears. The accuracy of tear detection improved after traction for the TFCC (98% after traction vs 83% before traction), the LTL (100% vs 88%), and the SLL (100% vs 95%). Tear visibility improved after traction for 54% of TFCC tears, 71% of LTL tears, and 66% of SLL tears. Wrist MR arthrography with axial traction significantly improved the visibility of articular cartilage and the detection and visibility of tears of the TFCC and intrinsic ligaments. The results favor more widespread use of traction during MR arthrography of the wrist.

  5. MR-Imaging optimisation of the articular hip cartilage by using a T{sub 1}-weighted 3-dimensional gradient-echo sequence and the application of a hip joint traction; Magnetresonanztomographische Optimierung der Hueftknorpeldarstellung durch die Wahl einer T{sub 1}-Volumen-Gradienten-Echo-Sequenz und die Anwendung einer Hueftgelenkstraktion

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, R. [Heidelberg Univ. (Germany). Orthopaedische Klinik und Poliklinik; Bernd, L. [Heidelberg Univ. (Germany). Orthopaedische Klinik und Poliklinik; Wrazidlo, W. [ATOS-Praxisklinik, Heidelberg (Germany). Radiologische Gemeinschaftspraxis Drs. Lederer, Schneider und Wrazidlo; Lederer, W. [ATOS-Praxisklinik, Heidelberg (Germany). Radiologische Gemeinschaftspraxis Drs. Lederer, Schneider und Wrazidlo; Schneider, S. [ATOS-Praxisklinik, Heidelberg (Germany). Radiologische Gemeinschaftspraxis Drs. Lederer, Schneider und Wrazidlo

    1995-10-01

    Images of three animal cadaver hips, 8 dissected patient femoral heads and 18 hip joints of human corpses, all either with arthrosis stage I-III or artificial cartilage defects, were compared with their corresponding anatomic sections. Additional histomorphologic examinations of the arthrotic cartilages were conducted, and MR-Imaging of 20 healthy and 21 arthrotic patient hips was performed using a specific traction method. Using a T{sub 1}-weighted 3-dimensional gradient-echo sequence and a traction of the hip joint, it was possible due to the low-signal imaging of the joint space to separate in vivo the high-signal femoral head cartilage from the high-signal acetabular cartilage. In horizontal position of the phase-encoding parameter, minimisation of the chemical-shift artifact, mainly in the ventro-lateral areas, was accomplished. MRI measurements of the articular cartilage widths showed significant correlations (p < 0.001) with the corresponding anatomic sections. At the same time the T{sub 1} 3-dimensional gradient-echo sequence of the lateral femoral head with r = 0.94 showed the lowest deviations of the measurements. It was possible with MR-Imaging to distinguish four cartilage qualities. (orig./MG) [Deutsch] Im experimentellen Teil der Studie wurden den MRT-Bildern von drei Kadavertierhueften, 8 resezierten Patientenhueftkoepfen und 18 Leichenhueftgelenken, an denen entweder artifizielle Knorpeldefekte gesetzt wurden oder die ein Koxarthrose-Stadium I-III aufwiesen, die korrespondierenden makroskopischen Kryomikrotomschnitte zugeordnet. Bei den Koxarthrosen erfolgten zusaetzliche histomorphologische Knorpeluntersuchungen. Im klinischen Teil der Studie wurden 20 gesunde und 21 arthrotische Probandenhueftgelenke mit einem speziellen Traktionsverfahren untersucht. Unter Anwendung einer T{sub 1}-Volumen-Gradienten-Echo-Sequenz und einer Traktion am zu untersuchenden Hueftgelenk konnte in vivo durch die signalarme Darstellung des Gelenkspaltes der

  6. Electrical Energy Quality Studies in 3 kV DC Electric Traction Systems for Different Schemes of Connection Traction Substation to Power Utility System

    Directory of Open Access Journals (Sweden)

    Leszek Mierzejewski

    2004-01-01

    Full Text Available The paper present aspects of DC electric traction system influence on electric energetic system. Study is based on modeling and simulation of electrified railway line. After simulation, there was performed analysis of energy quality, whitch using results of simulation and supply systems parameters.

  7. New model of inverting substation for DC traction with regenerative braking system

    Science.gov (United States)

    Omar, Abdul Malek Saidina; Samat, Ahmad Asri Abd; Isa, Siti Sarah Mat; Shamsuddin, Sarah Addyani; Jamaludin, Nur Fadhilah; Khyasudeen, Muhammad Farris

    2017-08-01

    This paper presents a power electronic devices application focus on modeling, analysis, and control of switching power converter in the inverting DC substation with regenerative braking system which is used to recycle the surplus regenerative power by feed it back to the main AC grid. The main objective of this research is to improve the switching power electronic converter of the railway inverting substation and optimize the maximum kinetic energy recovery together with minimum power losses from the railway braking system. Assess performance including efficiency and robustness will be evaluated in order to get the best solution for the design configuration. Research methodology included mathematical calculation, simulation, and detail analysis on modeling of switching power converter on inverting substation. The design stage separates to four main areas include rectification mode, regenerative mode, control inverter mode and filtering mode. The simulation result has shown that the regenerative inverter has a capability to accept a maximum recovery power on the regeneration mode. Total energy recovery has increase and power losses have decreases because inverter abilities to transfer the surplus energy back to the main AC supply. An Inverter controller with PWM Generator and PI Voltage Regulator has been designed to control voltage magnitude and frequency of the DC traction system.

  8. Partial-thickness macular hole in vitreomacular traction syndrome: a case report and review of the literature

    Directory of Open Access Journals (Sweden)

    Al Sabti Khalid

    2010-01-01

    Full Text Available Abstract Introduction Vitreomacular traction syndrome has recently been recognized as a distinct clinical condition. It may lead to many complications, such as cystoid macular edema, macular pucker formation, tractional macular detachment, and full-thickness macular hole formation. Case presentation We report a case of vitreomacular traction syndrome with eccentric traction at the macula and a partial-thickness macular hole in a 63-year-old Pakistani Punjabi man. The patient was evaluated using optical coherence tomography, and he underwent a successful pars plana vitrectomy. After the operation, his foveal contour regained normal configuration, and his visual acuity improved from 20/60 to 20/30. Conclusions Pars plana vitrectomy prevents the progression of a partial thickness macular hole in vitreomacular traction syndrome. The relief of traction by vitrectomy restores foveal anatomy and visual acuity in this condition.

  9. The Effect of 2 Forms of Talocrural Joint Traction on Dorsiflexion Range of Motion and Postural Control in Those With Chronic Ankle Instability.

    Science.gov (United States)

    Powden, Cameron J; Hogan, Kathleen K; Wikstrom, Erik A; Hoch, Matthew C

    2017-05-01

    Talocrural joint mobilizations are commonly used to address deficits associated with chronic ankle instability (CAI). Examine the immediate effects of talocrural joint traction in those with CAI. Blinded, crossover. Laboratory. Twenty adults (14 females; age = 23.80 ± 4.02 y; height = 169.55 ± 12.38 cm; weight = 78.34 ± 16.32 kg) with self-reported CAI participated. Inclusion criteria consisted of a history of ≥1 ankle sprain, ≥2 episodes of giving way in the previous 3 mo, answering "yes" to ≥4 questions on the Ankle Instability Instrument, and ≤24 on the Cumberland Ankle Instability Tool. Subjects participated in 3 sessions in which they received a single treatment session of sustained traction (ST), oscillatory traction (OT), or a sham condition in a randomized order. Interventions consisted of four 30-s sets of traction with 1 min of rest between sets. During ST and OT, the talus was distracted distally from the ankle mortise to the end-range of accessory motion. ST consisted of continuous distraction and OT involved 1-s oscillations between the mid and end-range of accessory motion. The sham condition consisted of physical contact without force application. Preintervention and postintervention measurements of weight-bearing dorsiflexion, dynamic balance, and static single-limb balance were collected. The independent variable was treatment (ST, OT, sham). The dependent variables included pre-to-posttreatment change scores for the WBLT (cm), normalized SEBTAR (%), and time-to-boundary (TTB) variables(s). Separate 1-way ANOVAs examined differences between treatments for each dependent variable. Alpha was set a priori at P manual therapies.

  10. ENERGY EFFICIENCY DETERMINATION OF LOADING-BACK SYSTEM OF ELECTRIC TRACTION MACHINES

    Directory of Open Access Journals (Sweden)

    A. M. Afanasov

    2014-03-01

    Full Text Available Purpose.Acceptance post-repair testsof electric traction machinesare conducted onloading-backstandsthat reducethe overall power costsfor the tests.Currentlya numberof possiblecircuit designs of loading-backsystems of electric machines are known, but there is nomethod of determiningtheir energy efficiency. This in turn makes difficult the choiceof rationaloptions. The purpose of the article is the development of the corresponding methodo-logy to make easier this process. Methodology. Expressions for determining theenergy efficiency ofa stand for testingof electric traction machineswere obtained using the generalizedscheme analysisof energy transformationsin the loading-backsystems of universal structure. Findings.Thetechnique wasoffered and the analytical expressions for determining the energy efficiency of loading-backsystemsof electric traction machines wereobtained. Energy efficiency coefficientofloading-backsystemisproposed to consider as the ratio of the total actionenergy of the mechanical and electromotive forces, providing anchors rotation and flowof currents in electric machines, which are being tested,to the total energy, consumed during the test from the external network. Originality. The concept was introduced and the analytical determination method of the energy efficiency of loading-backsystem in electric traction machines was offered. It differs by efficiency availability of power sources and converters, as well as energy efficiency factors of indirect methods of loss compensation. Practical value. The proposed technique of energy efficiency estimation of a loading-backsystemcan be used in solving the problem of rational options choice of schematics stands decisions for electric traction machines acceptance tests of main line and industrial transport.

  11. The aspect of vector control using the asynchronous traction motor in locomotives

    Directory of Open Access Journals (Sweden)

    L. Liudvinavičius

    2009-12-01

    Full Text Available The article examines curves controlling asynchronous traction motors increasingly used in locomotive electric drives the main task of which is to create a tractive effort-speed curve of an ideal locomotive Fk = f(v, including a hyperbolic area the curve of which will create conditions showing that energy created by the diesel engine of diesel locomotives (electric locomotives and in case of electric trains, electricity taken from the contact network over the entire range of locomotive speed is turned into efficient work. Mechanical power on wheel sets is constant Pk = Fkv = const, the power of the diesel engine is fully used over the entire range of locomotive speed. Tractive effort-speed curve Fk(v shows the dependency of locomotive traction power Fk on movement speed v. The article presents theoretical and practical aspects relevant to creating the structure of locomotive electric drive and selecting optimal control that is especially relevant to creating the structure of locomotive electric drive using ATM (asynchronous traction motor that gains special popularity in traction rolling stock replacing DC traction motors having low reliability. The frequency modes of asynchronous motor speed regulation are examined. To control ATM, the authors suggest the method of vector control presenting the structural schemes of a locomotive with ATM and control algorithm.

  12. A Comprehensive Study of Neutralizing Antigenic Sites on the Hepatitis E Virus (HEV) Capsid by Constructing, Clustering, and Characterizing a Tool Box*

    Science.gov (United States)

    Zhao, Min; Li, Xiao-Jing; Tang, Zi-Min; Yang, Fan; Wang, Si-Ling; Cai, Wei; Zhang, Ke; Xia, Ning-Shao; Zheng, Zi-Zheng

    2015-01-01

    The hepatitis E virus (HEV) ORF2 encodes a single structural capsid protein. The E2s domain (amino acids 459–606) of the capsid protein has been identified as the major immune target. All identified neutralizing epitopes are located on this domain; however, a comprehensive characterization of antigenic sites on the domain is lacking due to its high degree of conformation dependence. Here, we used the statistical software SPSS to analyze cELISA (competitive ELISA) data to classify monoclonal antibodies (mAbs), which recognized conformational epitopes on E2s domain. Using this novel analysis method, we identified various conformational mAbs that recognized the E2s domain. These mAbs were distributed into 6 independent groups, suggesting the presence of at least 6 epitopes. Twelve representative mAbs covering the six groups were selected as a tool box to further map functional antigenic sites on the E2s domain. By combining functional and location information of the 12 representative mAbs, this study provided a complete picture of potential neutralizing epitope regions and immune-dominant determinants on E2s domain. One epitope region is located on top of the E2s domain close to the monomer interface; the other is located on the monomer side of the E2s dimer around the groove zone. Besides, two non-neutralizing epitopes were also identified on E2s domain that did not stimulate neutralizing antibodies. Our results help further the understanding of protective mechanisms induced by the HEV vaccine. Furthermore, the tool box with 12 representative mAbs will be useful for studying the HEV infection process. PMID:26085097

  13. Optimal arm posture control and tendon traction forces of a coupled tendon-driven manipulator

    International Nuclear Information System (INIS)

    Ma, Shugen

    1997-01-01

    In this study, the optimum arm posture of a coupled tendon-driven multijoint manipulator arm (or CT Arm) at maximum payload output was derived and the corresponding tendon traction forces were also analyzed, during management of a heavy payload by the manipulator in a gravity environment. The CT Arm is special tendon traction transmission mechanism in which a pair of tendons used to drive a joint is pulled from base actuators via pulleys mounted on the base-side joints. This mechanism enables optimal utilization of the coupled drive function of tendon traction forces and thus enables the lightweight manipulator to exhibit large payload capability. The properties of the CT Arm mechanism are elucidated by the proposed optimal posture control scheme. Computer simulation was also executed to verify the validity of the proposed control scheme. (author)

  14. Effects of traction on the blood circulation of femoral head: DSA study on a canine model

    International Nuclear Information System (INIS)

    Yang Xiujun; Xiao Jian; Ren Qile; Fu Shiping; Li Wei; Xiao Xiangsheng

    2010-01-01

    Objective: To study the influence of traction on the blood circulation of femur head and its evaluation by DSA. Methods: Using micro-catheter, transfemoral selective femoral circumflex arteriography in 22 healthy dogs was performed in unilateral hip before (Group A, n=22) and immediately (Group B, n=22), 30 (Group D, n=22), 60 (Group E, n=20), 90 (Group F, n=10), 120 (Group G, n= 10) minutes during 2 kg skin hip traction, and immediately after traction removal (Group H, I, J, L and O) , and 30 minutes after traction removal with 60, 90 and 120 minutes continuous traction (Group K, M and P) , and 60 minutes after traction removal with 90 and 120 minutes continuous traction (Group N and Q). DSA was also performed immediately during 4 kg weight traction before continuous traction in 12 hips (Group C). Blood circulation of the femoral head was evaluated mainly by observing its perfusion and time of circulation. Femur head perfusion was assessed as good scoring 3, poor scoring 2 and extremely poor scoring 1. Femur head circulation time was assessed as normal scoring 3, prolonged scoring 2 and remarkably prolonged scoring 1. Analysis of variance was employed for analysis of the angiographic findings between different groups. Results: Good femoral head perfusion in Group A to Q was 22, 0, 0, 0, 0, 0, 0, 22, 22, 1, 18, 0, 0, 8, 0, 0 and 1 hips respectively, poor one was 0, 22, 8, 22, 15, 4, 1, 0, 0, 15, 2, 4, 6, 2, 1, 3 and 8 hips, respectively, extremely poor one was 0, 0, 4, 0, 5, 6, 9, 0, 0, 4, 0, 6, 4, 0, 9, 7 and 1 hips, respectively; and normal femoral head blood circulation time was 22, 0, 0, 0, 0, 0, 0, 22, 22, 1, 18, 0, 0, 8, 0, 0 and 1 hips, respectively, prolonged one was 0, 22, 9, 22, 15, 4, 2, 0, 0, 15, 2, 5, 7, 2, 2, 4 and 8 hips, respectively, remarkably prolonged one was 0, 0, 3, 0, 5, 6, 8, 0, 0, 4, 0, 5, 3, 0, 8, 6 and 1 hips, respectively. F value of femoral head perfusion among group A and B,group B and C, group B, D, E, F and G, Group H, I, J, L and O

  15. Traction endurance biomechanical study of metallic suture anchors at different insertion angles

    Directory of Open Access Journals (Sweden)

    Azato Flávia Namie

    2003-01-01

    Full Text Available The suture anchors' insertion angle and its traction resistance are the main subjects of this study. Twenty trials were realized using threaded suture anchors in four diferents angulations (30º /45º /60º /90º in human bone (distal femur and another twenty trials in artificial bone (SawboneTM. The anchors were pulled out being tractioned uprightly from its bone surface by a Kratos Universal test machine. The human bone results found no relation between the main subjects of this study, so whithout statistical value. On the other hand at the artificial bone the insertion angle of 90º beared more traction, being statistically significant compared to the other angles.

  16. Ulnar nerve injury due to lateral traction device during shoulder arthroscopy: Was it avoidable?

    Directory of Open Access Journals (Sweden)

    Vivek Pandey

    2017-01-01

    Full Text Available Most of the nerve injuries reported during shoulder arthroscopy in a beach chair, or lateral position is related to inappropriate patient positioning or excess traction. The lateral decubitus position is more vulnerable for traction-related neuropraxia. The present case serves as an important lesson from an avoidable situation of “having a one track mind” of the surgical team during the arthroscopic repair of shoulder instability performed in the lateral decubitus position. The operating surgeon must supervise the appropriate positioning of the patient on operation table and adequate padding of vulnerable bony points before beginning of shoulder arthroscopy to prevent any position-related nerve injuries. This is probably the first case to illustrate an unusual cause of ulnar nerve compression particularly related to the use of an additional traction device in the arthroscopic repair of shoulder instability performed in lateral decubitus position, which has not been previously defined.

  17. Experimental research of vehicle traction properties for reconstruction of traffic accidents

    Directory of Open Access Journals (Sweden)

    Dudziak Marian

    2018-01-01

    Full Text Available In order to broaden the database of motor vehicle traction properties in unusual conditions, the research team has performed experimental studies: on wet and snow-covered surfaces. Tests of vehicles equipped with winter tyres with non-skid snow chains have been performed on snow-covered surfaces. It has been shown that on snowy surface chains affect vehicle traction properties, mostly during acceleration. They increase the rate of acceleration up to 50% compared to a vehicle with winter tyres without chains. The results of the performed research can be the basis for the full reconstruction of road accidents under these conditions. Knowledge of traction properties of cars in difficult and unusual conditions is an important cognitive factor and serves to improve road safety.

  18. Severe Postoperative Complications may be Related to Mesenteric Traction Syndrome during Open Esophagectomy

    DEFF Research Database (Denmark)

    Ambrus, R; Svendsen, L B; Secher, N H

    2017-01-01

    . RESULTS: Flushing appeared in 17 (open) and 5 (robotically assisted) surgical cases ( p = 0.001). Mean arterial pressure was stable during both types of surgeries, but infusion of vasopressors during the first hour of open surgery was related to development of widespread (Grade II) flushing ( p = 0......BACKGROUND: During abdominal surgery, traction of the mesenterium provokes mesenteric traction syndrome, including hypotension, tachycardia, and flushing, along with an increase in plasma prostacyclin (PGI2). We evaluated whether postoperative complications are related to mesenteric traction...... syndrome during esophagectomy. METHODS: Flushing, hemodynamic variables, and plasma 6-keto-PGF1α were recorded during the abdominal part of open ( n = 25) and robotically assisted ( n = 25) esophagectomy. Postoperative complications were also registered, according to the Clavien-Dindo classification...

  19. Halo-gravity traction in the treatment of severe spinal deformity: a systematic review and meta-analysis.

    Science.gov (United States)

    Yang, Changsheng; Wang, Huafeng; Zheng, Zhaomin; Zhang, Zhongmin; Wang, Jianru; Liu, Hui; Kim, Yongjung Jay; Cho, Samuel

    2017-07-01

    Halo-gravity traction has been reported to successfully assist in managing severe spinal deformity. This is a systematic review of all studies on halo-gravity traction in the treatment of spinal deformity to provide information for clinical practice. A comprehensive search was conducted for articles on halo-gravity traction in the treatment of spinal deformity according to the PRISMA guidelines. Appropriate studies would be included and analyzed. Preoperative correction rate of spinal deformity, change of pulmonary function and prevalence of complications were the main measurements. Sixteen studies, a total of 351 patients, were included in this review. Generally, the initial Cobb angle was 101.1° in the coronal plane and 80.5° in the sagittal plane, and it was corrected to 49.4° and 56.0° after final spinal fusion. The preoperative correction due to traction alone was 24.1 and 19.3%, respectively. With traction, the flexibility improved 6.1% but postoperatively the patients did not have better correction. Less aggressive procedures and improved pulmonary function were observed in patients with traction. The prevalence of traction-related complications was 22% and three cases of neurologic complication related to traction were noted. The prevalence of total complications related to surgery was 32% and that of neurologic complications was 1%. Partial correction could be achieved preoperatively with halo-gravity traction, and it may help decrease aggressive procedures, improve preoperative pulmonary function, and reduce neurologic complications. However, traction could not increase preoperative flexibility or final correction. Traction-related complications, although usually not severe, were not rare.

  20. Occurrence and prevalence of selected zoonotic agents: Echinococcus multilocularis, Trichinella spiralis and hepatitis E virus (HEV) in the population of Polish hunters--results of the study conducted in 2010-2012.

    Science.gov (United States)

    Sadkowska-Todys, Małgorzata; Baumann-Popczyk, Anna; Wnukowska, Natalia; Popczyk, Bartłomiej; Kucharczyk, Bożena; Gołąb, Elżbieta

    2015-01-01

    In Poland the development of the knowledge concerning zoonotic pathogens, of which free-living animals are the reservoir of is gaining in importance both in epidemiological aspect as well as in the context of prevention for improving public health. Dietary habits such as the consumption of forest undergrowth products and wild game meat, and the way of those products being prepared (in the process of barbequing) pose a risk factors of infection with the foodborne pathogens such as Echinococcus multilocularis, Trichinella spp., and HEV. The aim of this study is to estimate the prevalence of infections caused by Trichinella spp., Echinococcus multilocularis, and HEV in the population of Polish hunters, describing their geographical distribution in Poland, and to try to define basic factors, which may contribute to their occurrence. In 2010-2012 a cross-sectional study was carried out among Polish hunters. A blood samples were collected as well as a survey of 1027 participants recruited in the 16 provinces was also carried out. Serological tests were performed for the presence of specific antibodies against Echinococcus multilocularis, Trichinella spp. and HEV using commercial or "in home" ELISA tests. In case of positive result for Echinococcus, an Em2plus ELISA or/and western blot test were carried out, and for positive results for IgM for HEV a recomLine HEV IgM test was carried out. In the studied population a total number of 2 cases of Echinococcus multilocularis infection were found. Moreover in 47 (4,6%) participants presence of antibodies against Trichinella spp. were found, including 17 positive and 30 borderline results. In 206 persons (25%) IgG anti-HEV antibodies were found (by ELISA test). Geographical diversity in prevalence of both, the Trichinella spp. and HEV cases was observed. The study confirmed presence of zoonotic infections such as Echinococcus multilocularis, Trichinella spp., and hepatitis E (HEV) among Polish hunters. In the case of

  1. Comparison of the environmental performance of light mechanization and animal traction using a modular LCA approach

    DEFF Research Database (Denmark)

    Cerutti, Alessandro K.; Calvo, Angela; Bruun, Sander

    2014-01-01

    Animal traction has supported humans in most field operations since the origin of agriculture. With the introduction of mechanization, humans gained access to much more work power at similar management costs and were able to significantly increase the productivity and time efficiency of field...... Italy, while use of machine traction was evaluated using field data on two-wheel tractors performing the operations in similar production systems, converted to the specific functional unit. Owing to the differing properties of mechanical and living systems, it was difficult to establish a reliable...

  2. Simulation of Trolleybus Traction Induction Drive With Supercapacitor Energy Storage System

    Science.gov (United States)

    Brazis, V.; Latkovskis, L.; Grigans, L.

    2010-01-01

    The article considers the possibilities of saving the regenerative braking energy in Škoda 24Tr type trolleybuses by installing the onboard supercapacitor energy storage system (ESS) and improving its performance with automated switching to the autonomous traction mode. Proposed is an ESS control system with constant DC bus voltage in the supercapacitor charging mode and supercapacitor current proportional to the AC drive current in the discharging mode. The authors investigate stability of the trolleybus ESS control system operating together with AC traction drive in various overhead voltage failure modes. The co-simulation of ESS operation was done by Matlab/Simulink AC drive and PSIM ESS continuous models.

  3. Parametric tests of a traction drive retrofitted to an automotive gas turbine

    Science.gov (United States)

    Rohn, D. A.; Lowenthal, S. H.; Anderson, N. E.

    1980-01-01

    The results of a test program to retrofit a high performance fixed ratio Nasvytis Multiroller Traction Drive in place of a helical gear set to a gas turbine engine are presented. Parametric tests up to a maximum engine power turbine speed of 45,500 rpm and to a power level of 11 kW were conducted. Comparisons were made to similar drives that were parametrically tested on a back-to-back test stand. The drive showed good compatibility with the gas turbine engine. Specific fuel consumption of the engine with the traction drive speed reducer installed was comparable to the original helical gearset equipped engine.

  4. Multiroller traction drive speed reducer: Evaluation for automotive gas turbine engine

    Science.gov (United States)

    Rohn, D. A.; Anderson, N. E.; Loewenthal, S. H.

    1982-01-01

    Tests were conducted on a nominal 14:1 fixed-ratio Nasvytis multiroller traction drive retrofitted as the speed reducer in an automotive gas turbine engine. Power turbine speeds of 45,000 rpm and a drive output power of 102 kW (137 hp) were reached. The drive operated under both variable roller loading (proportional to torque) and fixed roller loading (automatic loading mechanism locked). The drive operated smoothly and efficiently as the engine speed reducer. Engine specific fuel consumption with the traction speed reducer was comparable to that with the original helical gearset.

  5. ONCE AGAIN ABOUT DETERMINATION OF SAVING OF ENERGY FOR TRACTION DUE TO PARTIAL CUT–OFF OF TRACTION ENGINES OF ELECTRIC ROLLING STOCK

    Directory of Open Access Journals (Sweden)

    G. K. Getman

    2013-09-01

    Full Text Available Purpose. In general the well known methods for determination of energy saving due to the partial traction engines cut-off based on their comparison to efficiency coefficient or to the power of energy losses do not allow objective estimation of efficiency of these measures and in a number of cases result in erroneous results and errors. The search for new more advanced methods for determination of energy saving at the partial cut-off of the traction engines is needed. Methodology. The method of calculation determination of energy saving when partial cutting-off of the traction engines is offered. It is based on the use of rationality coefficient as the loading mode of the electric power consumption for the measuring instrument of transportation activity. Findings. Using the given mathematical expressions it is possible to determine the energy saving in both the relative and absolute values and set the terms (motion speed and route gradient, under which the energy saving will take place. Originality. The method of the task solving, which is based on the evaluation of energy consumption differences for the compared variants (not on the comparison of efficiency coefficient or differences of power of energy losses is offered. Practical value. The given methodology allows obtaining more exact conclusions in relation to the electric power consumption, as the comparison of energy losses power or the efficiency coefficient does not determine precisely the electric power consumption for traction. Therefore the conclusions based on the comparison of power of energy losses or efficiency coefficient can appear inexact.

  6. Systemic design of synchronous traction drives for large speed-range electric vehicle; Conception systemique de chaines de traction synchrones pour vehicule electrique a large gamme de vitesse

    Energy Technology Data Exchange (ETDEWEB)

    Randi, S.A.

    2003-04-15

    The presented study deals with a systemic approach based design of permanent magnet brush-less actuators. The considered system is the electric vehicle motorized with this actuator on a large speed range. First, the review of vehicles architectures and general specifications put emphasis on the design problem complexity and the interest of a simultaneous design taking account of the whole traction chain driving cycle. Then the IPM plane and lumped parameter models are used to bring out the variables which characterizes the work beyond the base speed and the ability in flux weakening operation. The properties of machines with two rotor parts in such operation are studied. The new degrees of freedom available with these structures bring new solutions for drives with larger speed range. Then a model taking account each subsystem is presented and implemented in a global SABER simulator, involving sizing models of components. This tool enables to study the work of the traction chain over significant driving cycles and the performances evaluation. A last, this simulator is brought into work so as to perform a simultaneous design of the traction chain components as battery, inverter, machine, gear, thanks to an optimisation procedure based on genetic algorithm able to process continuous sizes variations and structure modifications, considering performance criteria on losses and cost. (author)

  7. Traction and lubricant film temperature as related to the glass transition temperature and solidification. [using infrared spectroscopy on EHD contacts

    Science.gov (United States)

    Lauer, J. L.; Peterkin, M. E.

    1978-01-01

    Does a traction fluid have to be a glass or solid under operating conditions. Infrared spectra on dynamic EHD contacts of several types of fluid were used to determine the surface and oil-film temperatures. Polarized spectral runs were made to study molecular alignment. Static glass transition pressures at appropriate temperatures were between 0.1 and 2.0 GPa, with the traction fluid showing the highest. In the EHD contact region, the traction fluid showed both the highest film temperatures as well as the greatest degree of molecular alignment. A plot of the difference between the film and surface temperatures vs shear rate resulted in a master plot valid for all the fluids. From this work, the authors propose a model of 'fluid' traction, where friction between parallel rough molecules provides the traction.

  8. Agent-based modeling traction force mediated compaction of cell-populated collagen gels using physically realistic fibril mechanics.

    Science.gov (United States)

    Reinhardt, James W; Gooch, Keith J

    2014-02-01

    Agent-based modeling was used to model collagen fibrils, composed of a string of nodes serially connected by links that act as Hookean springs. Bending mechanics are implemented as torsional springs that act upon each set of three serially connected nodes as a linear function of angular deflection about the central node. These fibrils were evaluated under conditions that simulated axial extension, simple three-point bending and an end-loaded cantilever. The deformation of fibrils under axial loading varied <0.001% from the analytical solution for linearly elastic fibrils. For fibrils between 100 μm and 200 μm in length experiencing small deflections, differences between simulated deflections and their analytical solutions were <1% for fibrils experiencing three-point bending and <7% for fibrils experiencing cantilever bending. When these new rules for fibril mechanics were introduced into a model that allowed for cross-linking of fibrils to form a network and the application of cell traction force, the fibrous network underwent macroscopic compaction and aligned between cells. Further, fibril density increased between cells to a greater extent than that observed macroscopically and appeared similar to matrical tracks that have been observed experimentally in cell-populated collagen gels. This behavior is consistent with observations in previous versions of the model that did not allow for the physically realistic simulation of fibril mechanics. The significance of the torsional spring constant value was then explored to determine its impact on remodeling of the simulated fibrous network. Although a stronger torsional spring constant reduced the degree of quantitative remodeling that occurred, the inclusion of torsional springs in the model was not necessary for the model to reproduce key qualitative aspects of remodeling, indicating that the presence of Hookean springs is essential for this behavior. These results suggest that traction force mediated matrix

  9. The emergence of extracellular matrix mechanics and cell traction forces as important regulators of cellular self-organization.

    Science.gov (United States)

    Checa, Sara; Rausch, Manuel K; Petersen, Ansgar; Kuhl, Ellen; Duda, Georg N

    2015-01-01

    Physical cues play a fundamental role in a wide range of biological processes, such as embryogenesis, wound healing, tumour invasion and connective tissue morphogenesis. Although it is well known that during these processes, cells continuously interact with the local extracellular matrix (ECM) through cell traction forces, the role of these mechanical interactions on large scale cellular and matrix organization remains largely unknown. In this study, we use a simple theoretical model to investigate cellular and matrix organization as a result of mechanical feedback signals between cells and the surrounding ECM. The model includes bi-directional coupling through cellular traction forces to deform the ECM and through matrix deformation to trigger cellular migration. In addition, we incorporate the mechanical contribution of matrix fibres and their reorganization by the cells. We show that a group of contractile cells will self-polarize at a large scale, even in homogeneous environments. In addition, our simulations mimic the experimentally observed alignment of cells in the direction of maximum stiffness and the building up of tension as a consequence of cell and fibre reorganization. Moreover, we demonstrate that cellular organization is tightly linked to the mechanical feedback loop between cells and matrix. Cells with a preference for stiff environments have a tendency to form chains, while cells with a tendency for soft environments tend to form clusters. The model presented here illustrates the potential of simple physical cues and their impact on cellular self-organization. It can be used in applications where cell-matrix interactions play a key role, such as in the design of tissue engineering scaffolds and to gain a basic understanding of pattern formation in organogenesis or tissue regeneration.

  10. Spatial discretization methods for air gap permeance calculations in double salient traction motors

    NARCIS (Netherlands)

    Ilhan, E.; Kremers, M.F.J.; Motoasca, T.E.; Paulides, J.J.H.; Lomonova, E.

    2012-01-01

    Weight limitations in electric/hybrid cars demand the highest possible power-to-weight ratio from the traction motor, as in double salient permanent magnet (PM) machines. Their high flux densities in the air gap result in nonlinear analytical models, which need to be time optimized. The incorporated

  11. Performance Availability Assessment of Combined Multi Power Source Traction Drive Considering Real Operational Conditions

    Directory of Open Access Journals (Sweden)

    Frenkel Ilia

    2016-09-01

    Full Text Available The present paper deals with the vehicle’s traction electric drive, consisting of several various electric power sources. One of the main requirements for such systems are the safety and sustainable operations, achieved largely the implementation of an uninterrupted supply of the vehicle’s propulsion system with an electric power.

  12. Wavelet Entropy-Based Traction Inverter Open Switch Fault Diagnosis in High-Speed Railways

    Directory of Open Access Journals (Sweden)

    Keting Hu

    2016-03-01

    Full Text Available In this paper, a diagnosis plan is proposed to settle the detection and isolation problem of open switch faults in high-speed railway traction system traction inverters. Five entropy forms are discussed and compared with the traditional fault detection methods, namely, discrete wavelet transform and discrete wavelet packet transform. The traditional fault detection methods cannot efficiently detect the open switch faults in traction inverters because of the low resolution or the sudden change of the current. The performances of Wavelet Packet Energy Shannon Entropy (WPESE, Wavelet Packet Energy Tsallis Entropy (WPETE with different non-extensive parameters, Wavelet Packet Energy Shannon Entropy with a specific sub-band (WPESE3,6, Empirical Mode Decomposition Shannon Entropy (EMDESE, and Empirical Mode Decomposition Tsallis Entropy (EMDETE with non-extensive parameters in detecting the open switch fault are evaluated by the evaluation parameter. Comparison experiments are carried out to select the best entropy form for the traction inverter open switch fault detection. In addition, the DC component is adopted to isolate the failure Isolated Gate Bipolar Transistor (IGBT. The simulation experiments show that the proposed plan can diagnose single and simultaneous open switch faults correctly and timely.

  13. Severe Postoperative Complications may be Related to Mesenteric Traction Syndrome during Open Esophagectomy.

    Science.gov (United States)

    Ambrus, R; Svendsen, L B; Secher, N H; Goetze, J P; Rünitz, K; Achiam, M P

    2017-09-01

    During abdominal surgery, traction of the mesenterium provokes mesenteric traction syndrome, including hypotension, tachycardia, and flushing, along with an increase in plasma prostacyclin (PGI 2 ). We evaluated whether postoperative complications are related to mesenteric traction syndrome during esophagectomy. Flushing, hemodynamic variables, and plasma 6-keto-PGF 1α were recorded during the abdominal part of open ( n = 25) and robotically assisted ( n = 25) esophagectomy. Postoperative complications were also registered, according to the Clavien-Dindo classification. Flushing appeared in 17 (open) and 5 (robotically assisted) surgical cases ( p = 0.001). Mean arterial pressure was stable during both types of surgeries, but infusion of vasopressors during the first hour of open surgery was related to development of widespread (Grade II) flushing ( p = 0.036). For patients who developed flushing, heart rate and plasma 6-keto-PGF 1α also increased ( p = 0.001 and p syndrome manifests more frequently during open than robotically assisted esophagectomy, and postoperative complications appear to be associated with severe mesenteric traction syndrome.

  14. Quantifying the Traction Force of a Single Cell by Aligned Silicon Nanowire Array

    KAUST Repository

    Li, Zhou

    2009-10-14

    The physical behaviors of stationary cells, such as the morphology, motility, adhesion, anchorage, invasion and metastasis, are likely to be important for governing their biological characteristics. A change in the physical properties of mammalian cells could be an indication of disease. In this paper, we present a silicon-nanowire-array based technique for quantifying the mechanical behavior of single cells representing three distinct groups: normal mammalian cells, benign cells (L929), and malignant cells (HeLa). By culturing the cells on top of NW arrays, the maximum traction forces of two different tumor cells (HeLa, L929) have been measured by quantitatively analyzing the bending of the nanowires. The cancer cell exhibits a larger traction force than the normal cell by ∼20% for a HeLa cell and ∼50% for a L929 cell. The traction forces have been measured for the L929 cells and mechanocytes as a function of culture time. The relationship between cells extending area and their traction force has been investigated. Our study is likely important for studying the mechanical properties of single cells and their migration characteristics, possibly providing a new cellular level diagnostic technique. © 2009 American Chemical Society.

  15. Improving mandibular contour: A pilot study for indication of PPLA traction thread use.

    Science.gov (United States)

    Guida, Stefania; Persechino, Flavia; Rubino, Giuseppe; Pellacani, Giovanni; Farnetani, Francesca; Urtis, Giacomo Giovanni

    2018-02-20

    The request for less-aggressive procedures to improve mandibular contour is increasing. Several kinds of threads have been used for this purpose. Nevertheless, PLLA (poly-L-Lactic acid) traction thread procedure has not been previously described. To investigate the role of PLLA traction threads in improving mandibular contour. Twenty women were enrolled in the study. They were differentially classified for skin laxity. Patients were treated in a single session with two PLLA traction threads per side. Specific post-procedure instructions were given to patients, and complications occurred after the procedures were estimated. A Fisher's t-test was performed to identify criteria related to longevity of results. We found longevity of results to be associated with younger age (p = 0.001), absence of severe skin laxity of jawline and neck (p = 0.001), and aesthetic satisfaction (p = 0.024). Edema, swelling, and temporary skin contour irregularities were found in most cases (N = 16; 80%), whereas paresthesia resolving without sequelae in 2-4 weeks was found in two cases (10%). Our results show that selected patients, younger than 51 and showing a mild-moderate degree of skin laxity of jawline and neck angle represent ideal candidates for PLLA traction thread treatment. Further studies will be performed to confirm our results.

  16. Orthodontic Management with Traction and Asymmetric Extraction for Multiple Impacted Permanent Maxillary Teeth - A Case Report.

    Science.gov (United States)

    Niu, Qiannan; Zhang, Liang; Dai, Juan; Li, Feifei; Feng, Xue

    2016-01-01

    Multiple impacted teeth are a rare eruption disturbance that increases the case complexity. In this article, we described a 13-year-old boy whose 5 permanent maxillary teeth were not erupted although their root formation was complete. The orthodontic treatment with traction and asymmetric extraction was performed to achieve a significantly improved functional and esthetic result.

  17. Brushless traction PM Machines using commercial drive technology, part I: Design methodology and motor design

    NARCIS (Netherlands)

    Kazmin, Evgeny; Lomonova, E.A.; Paulides, J.J.H.

    2008-01-01

    A concept design approach for the brushless PM traction motor, which has crucial constraints on volume envelope and on the drive, is presented. The considered motor drive is the three-phase DC/AC converter, which is commercially available on the modern market of the standard variable frequency

  18. The determination of the pressure-viscosity coefficient of two traction oils using film thickness measurements

    NARCIS (Netherlands)

    Leeuwen, van H.J.

    2010-01-01

    The pressure-viscosity coefficients of two commercial traction fluids are determined by fitting calculation results on accurate film thickness measurements, obtained at a wide range of speeds, and different temperatures. Film thickness values are calculated using a numerical method and approximation

  19. Original Paper Effects of oxen yoke and donkey collar on traction ...

    African Journals Online (AJOL)

    The realization of mechanized zaï with draft animal encounters the weakness of hitch traction capabilities. To overcome this issue, a study was conducted in three villages in the northern Burkina Faso with the aim at evaluating the effect of improved yoke and improved collar respectively with oxen and donkey harnessing on ...

  20. Defining Strong State Accountability Systems: How Can Better Standards Gain Greater Traction? A First Look

    Science.gov (United States)

    Reed, Eileen; Scull, Janie; Slicker, Gerilyn; Winkler, Amber M.

    2012-01-01

    Rigorous standards and aligned assessments are vital tools for boosting education outcomes but they have little traction without strong accountability systems that attach consequences to performance. In this pilot study, Eileen Reed, Janie Scull, Gerilyn Slicker, and Amber Winkler lay out the essential features of such accountability systems,…

  1. Skull traction for cervical spinal injury in Enugu: A 5‑year ...

    African Journals Online (AJOL)

    2015-11-05

    Nov 5, 2015 ... Background: Treatment of cervical spine injury is the most challenging of all the injuries of the spine, and there is yet no agreement on the best method of care. Objective: We studied the complications and outcome of two skull traction devices used to treat cases of cervical spine injury in three centers in ...

  2. Increase of energy efficiency of testing of traction electric machines of direct and pulsating current

    Directory of Open Access Journals (Sweden)

    A.M. Afanasov

    2015-03-01

    Full Text Available The results of the analysis of the effect of the load current of traction electric machines when tested for heating on the total electricity consumption for the test are presented. It is shown that increase of load current at the heating test permits to significantly reduce the consumption of electrical energy, and reduce the testing time without reducing its quality.

  3. The history of modern spinal traction with particular reference to neural disorders.

    Science.gov (United States)

    Shterenshis, M V

    1997-03-01

    The last 200 years of the history of spinal traction is described in the present article. The study starts at the end of the 18th century with the works of JA Venel (1789) who tried to apply the Hippocratic idea to modern surgery. Orthopedic specialists of the last century were mostly preoccupied with corsets and the method gained broader popularity when neurologists paid attention to the similar method of suspension. The Russian neurologist Osip Mochutkovsky described suspension as a method for the treatment of tabes dorsalis in an article published in the Russian magazine 'Vratch' in 1883. His works became known in Europe when JM Charcot paid attention to it and published a special short monograph on this subject in 1889. This work was translated into English (1889) and Russian (1890) and the method became popular in the treatment of tabes dorsalis and other neurological diseases. The eminent Russian neurologist VM Bekhterev proposed the combination of body suspension with cervical traction (1893). Some years later Gilles de la Tourette promoted the use of spinal traction in his neurological clinic (1897). Unfortunately neurologists worked without the cooperation of orthopedic specialists. During the first decades of the 20th century suspension was also replaced by traction in neurology. This method was used by both neurologists and orthopedic specialists but in the last decades neurologists lost their interests in it and it found greater use in traumatology and in spinal surgery where it is still in use today.

  4. Distributed Active Traction Control System Applied to the RoboCup Middle Size League

    Directory of Open Access Journals (Sweden)

    José Almeida

    2013-10-01

    Full Text Available This work addresses the problem of traction control in mobile wheeled robots in the particular case of the RoboCup Middle Size League (MSL. The slip control problem is formulated using simple friction models for ISePorto Team Robots with a differential wheel configuration. Traction was also characterized experimentally in the MSL scenario for relevant game events. This work proposes a hierarchical traction control architecture which relies on local slip detection and control at each wheel, with relevant information being relayed to a higher level responsible for global robot motion control. A dedicated one axis control embedded hardware subsystem allowing complex local control, high frequency current sensing and odometric information procession was developed. This local axis control board is integrated in a distributed system using CAN bus communications. The slipping observer was implemented in the axis control hardware nodes integrated in the ISePorto Robots and was used to control and detect loss of traction. An external vision system was used to perform a qualitative analysis of the slip detection and observer performance results are presented.

  5. Operation analysis of AC traction motors in terms of electromagnetic torque capability on sustainable railway vehicles

    Directory of Open Access Journals (Sweden)

    Bulucea Cornelia A.

    2016-01-01

    Full Text Available Sustainable operation of electric railway systems represents a significant purpose nowadays in the development of high power and high speed locomotives and trains. At present, high speed electric vehicles mostly work with three-phase induction motors or three-phase synchronous motors as traction motors. The two electric machine types have different efficiencies at different operation points, and experience differences with respect to safety, speed and power, energy use and exergy efficiency. An important issue that correlates these aspects is the electromagnetic torque developed by an electric traction motor. In order to provide an overview of the technical performance of the operation of sustainable railway systems, a detailed analysis is carried out of the electromagnetic torque capability of AC electric motors utilized as traction motors in modern locomotives of high power and/or high speed. The results of this work may help in enhancing the main criteria for optimising the safe and sustainable operation of electric railway traction systems.

  6. Efficacy of Prone Lumbar Traction on Chronic Discogenic Low Back Pain and Disability

    Directory of Open Access Journals (Sweden)

    Mahmoud Beyki

    2007-09-01

    Full Text Available Objectives: To compare the outcomes of prone and supine lumbar traction in patients with chronic discogenic low back pain. Methods: The test was prospective and randomized control trial. The structure of trial was Urban Physical Medicine and Rehabilitation clinic. Participants was included of A total of 124 subjects with chronic low back pain (LBP and evidence of a degenerative and/or herniated inter-vertebral disk at 1 or more levels of the lumbar spine, who have not our exclusion criteria. There was A 4-week course of lumbar traction, prone or supine in case and control groups consecutively, consisting of six 30-minute sessions every other days, followed by four 30-minute sessions every 3 days. The numeric Visual pain rating scale and the Oswestry Disability Index (ODI were completed at pre-intervention and discharge (within 2 weeks of the last visit. Results: A total of 124 subjects completed the treatment protocol. We noted significant improvements for all post-intervention outcome scores when compared with pre-intervention scores (P<0.01. Also found significant difference between 2 groups in favor of prone traction (P<0.01 Discussion: Traction applied in the prone position for 4 weeks was associated with improvements in pain intensity and ODI scores at discharge, in a sample of patients with activity limiting LBP. However, because we lacked a reasonable long time follow-up, we cannot imply a long lasting relationship between the traction and outcome, and a long time follow-up is suggested.

  7. Effects of Different Angles of the Traction Table on Lumbar Spine Ligaments: A Finite Element Study.

    Science.gov (United States)

    Farajpour, Hekmat; Jamshidi, Nima

    2017-12-01

    The traction bed is a noninvasive device for treating lower back pain caused by herniated intervertebral discs. In this study, we investigated the impact of the traction bed on the lower back as a means of increasing the disc height and creating a gap between facet joints. Computed tomography (CT) images were obtained from a female volunteer and a three-dimensional (3D) model was created using software package MIMICs 17.0. Afterwards, the 3D model was analyzed in an analytical software (Abaqus 6.14). The study was conducted under the following traction loads: 25%, 45%, 55%, and 85% of the whole body weight in different angles. Results indicated that the loading angle in the L3-4 area had 36.8%, 57.4%, 55.32%, 49.8%, and 52.15% effect on the anterior longitudinal ligament, posterior longitudinal ligament, intertransverse ligament, interspinous ligament, and supraspinous ligament, respectively. The respective values for the L4-5 area were 32.3%, 10.6%, 53.4%, 56.58%, and 57.35%. Also, the body weight had 63.2%, 42.6%, 44.68%, 50.2%, and 47.85% effect on the anterior longitudinal ligament, posterior longitudinal ligament, intertransverse ligament, interspinous ligament, and supraspinous ligament, respectively. The respective values for the L4-5 area were 67.7%, 89.4%, 46.6%, 43.42% and 42.65%. The authenticity of results was checked by comparing with the experimental data. The results show that traction beds are highly effective for disc movement and lower back pain relief. Also, an optimal angle for traction can be obtained in a 3D model analysis using CT or magnetic resonance imaging images. The optimal angle would be different for different patients and thus should be determined based on the decreased height of the intervertebral disc, weight and height of patients.

  8. Posterior-only surgery with preoperative skeletal traction for management of severe scoliosis.

    Science.gov (United States)

    Mehrpour, Saeedreza; Sorbi, Reza; Rezaei, Reza; Mazda, Keyvan

    2017-04-01

    The surgical treatment of severe adolescent spinal deformities is challenging and carries substantial risks of mortality and morbidity. To mitigate this risk, surgeons have employed various methods as this study designed to evaluate the safety and effectiveness of preoperative halo-femoral or halo gravity traction (HGT) followed by posterior-only surgery in the management of severe scoliosis. A total number of 23 patients with severe scoliosis treated by preoperative skeletal traction (halo gravity or halo femoral) followed by posterior fusion and instrumentation in one stage. All patients were followed for a minimum of 2 years after surgery. The average age of the patients was 12.7 years at the time of surgery. Mean of the Cobb angle improved from 99.9° ± 8.2° preoperatively to 75.3° ± 8° post-traction and 49.5° ± 7.7° postoperatively. Kyphosis angle corrected from 56.4° ± 9.5° to 38.6° ± 5.8°. The preop-FVC% was 41 ± 6.1% and after 1 year follow-up FVC% was 45.7 ± 7.7%. No patients required an anterior release due to amount of their deformity. Despite the benefits of modern instrumentation procedures, the treatment of severe scoliosis can be very competing. We think that by applying preoperative halo femoral traction and halo-gravity traction, managing severe scoliosis will be in safe and easy manner and can lead to better deformity correction and less neurological complications and facilitate to avoid anterior operation for severe scoliosis and its related complications.

  9. ELECTRODYNAMICS OF TRANSMISSION AND LOSSES OF POWER IN THE DEVICES OF ELECTRIC TRACTION SYSTEMS

    Directory of Open Access Journals (Sweden)

    M. O. Kostin

    2014-01-01

    Full Text Available Purpose. Theoretical justification of the "field" approach (based on electromagnetic field to the transmission and losses of power in the devices of traction power supply systems and electric rolling stock. Methodology. The methods of electromagnetic field theory and, in particular, the theory and practice of electromagnetic energy transmission based on the concept of the Poynting vector and elements of the theory of propagation, reflection and refraction of plane electromagnetic waves were used. Findings. Theoretical studies of electromagnetic energy transmission from the traction substation to the electric rolling stock through dielectric (air surrounding traction network: between the contact wire and the rail were carried out. It is proposed strategic designing "squat" (low types of electric rolling stock. The components of electric energy flow through the roof of electric rolling stock and its frontal part of the body were estimated. This allows reliable etimating active power losses in electric traction system. To compensate the reactive power consumed by electric rolling stock, which is conditioned by standing waves, it is proposed (for extinction of the the last to develop and put in front of electric rolling stock the layer of particular environment with the necessary parameters. Originality. The "field" principle of the power transmission analysis and its losses arising in electric traction system was first proposed. The laws of motion of electromagnetic energy flows through the roof and the frontal part of the body of electric rolling stock were established. Practical value. An expression of the absolute value of the Poynting vector in the points of dielectric (air between the contact wire and the rail was obtained. This allows assessing the highest density of energy, which is transferred to the time unit and predicting the main dimensions of the unit of electric rolling stock. The energy indices of the roof of electric rolling stock

  10. Long-Life, Lightweight, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration

    Science.gov (United States)

    Klein, Richard C.; Fusaro, Robert L.; Dimofte, Florin

    2012-01-01

    NASA s initiative for Lunar and Martian exploration will require long lived, robust drive systems for manned vehicles that must operate in hostile environments. The operation of these mechanical drives will pose a problem because of the existing extreme operating conditions. Some of these extreme conditions include operating at a very high or very cold temperature, operating over a wide range of temperatures, operating in very dusty environments, operating in a very high radiation environment, and operating in possibly corrosive environments. Current drive systems use gears with various configurations of teeth. These gears must be lubricated with oil (or grease) and must have some sort of a lubricant resupply system. For drive systems, oil poses problems such as evaporation, becoming too viscous and eventually freezing at cold temperatures, being too thin to lubricate at high temperatures, being degraded by the radiation environment, being contaminated by the regolith (soil), and if vaporized (and not sealed), it will contaminate the regolith. Thus, it may not be advisable or even possible to use oil because of these limitations. An oil-less, compact traction vehicle drive is a drive designed for use in hostile environments like those that will be encountered on planetary surfaces. Initially, traction roller tests in vacuum were conducted to obtain traction and endurance data needed for designing the drives. From that data, a traction drive was designed that would fit into a prototype lunar rover vehicle, and this design data was used to construct several traction drives. These drives were then tested in air to determine their performance characteristics, and if any final corrections to the designs were necessary. A limitation with current speed reducer systems such as planetary gears and harmonic drives is the high-contact stresses that occur at tooth engagement and in the harmonic drive wave generator interface. These high stresses induce high wear of solid

  11. METHODS AND RESEARCH CONCERNING SERVICE LIFE EXTENSION OF SUPORTING STRUCTURES OF TRACTION ROLLING STOCK FOR INDUSTRIAL TRANSPORT

    Directory of Open Access Journals (Sweden)

    O. M. Bondarev

    2014-04-01

    Full Text Available Purpose. The purpose of work is scientifically grounded introduction of the acquired techniques into works for service life extension of the traction and motor rolling stock for industrial transport. Methodology. To achieve the purpose it was analyzed the acquired techniques for service life extension of the traction and motor rolling stock for mainline transport. The acquired techniques during solution of problems concerning the service life extension of rolling stock units were adapted to the locomotives TGM6A and traction aggregates OPE1. Findings. On the basis of experimental and theoretical complex of studies some results were obtained. They gave the ground to determine the possibility of acquired techniques use when solving the problems on service life extension of rolling stock units concerning locomotives TGM6A and traction aggregates OPE1. Originality. On the basis of conducted experimental and theoretical studies scientific maintenance of the works providing extension of service life of traction and motor units of industrial rolling stock was executed. Practical value. Technical solutions and measures, which have to be carried out during operation within the prolonged appointed service life of traction and motor units of industrial rolling stock enterprises using locomotives and traction aggregates to provide the basic technological cycles were developed.

  12. Diagnostic performance of direct traction MR arthrography of the hip: detection of chondral and labral lesions with arthroscopic comparison

    International Nuclear Information System (INIS)

    Schmaranzer, Florian; Klauser, Andrea; Henninger, Benjamin; Kogler, Michael; Schmaranzer, Ehrenfried; Forstner, Thomas; Reichkendler, Markus

    2015-01-01

    To assess diagnostic performance of traction MR arthrography of the hip in detection and grading of chondral and labral lesions with arthroscopic comparison. Seventy-five MR arthrograms obtained ± traction of 73 consecutive patients (mean age, 34.5 years; range, 14-54 years) who underwent arthroscopy were included. Traction technique included weight-adapted traction (15-23 kg), a supporting plate for the contralateral leg, and intra-articular injection of 18-27 ml (local anaesthetic and contrast agent). Patients reported on neuropraxia and on pain. Two blinded readers independently assessed femoroacetabular cartilage and labrum lesions which were correlated with arthroscopy. Interobserver agreement was calculated using κ values. Joint distraction ± traction was evaluated in consensus. No procedure had to be stopped. There were no cases of neuropraxia. Accuracy for detection of labral lesions was 92 %/93 %, 91 %/83 % for acetabular lesions, and 92 %/88 % for femoral cartilage lesions for reader 1/reader 2, respectively. Interobserver agreement was moderate (κ = 0.58) for grading of labrum lesions and substantial (κ = 0.7, κ = 0.68) for grading of acetabular and femoral cartilage lesions. Joint distraction was achieved in 72/75 and 14/75 hips with/without traction, respectively. Traction MR arthrography safely enabled accurate detection and grading of labral and chondral lesions. (orig.)

  13. Diagnostic performance of direct traction MR arthrography of the hip: detection of chondral and labral lesions with arthroscopic comparison

    Energy Technology Data Exchange (ETDEWEB)

    Schmaranzer, Florian; Klauser, Andrea; Henninger, Benjamin [Medical University Innsbruck, Department of Radiology, Innsbruck (Austria); Kogler, Michael; Schmaranzer, Ehrenfried [District Hospital St. Johann in Tyrol, Department of Radiology, St. Johann in Tyrol (Austria); Forstner, Thomas [Johannes Keppler University, Department for Applied Systems Research and Statistics, Linz (Austria); Reichkendler, Markus [District Hospital St. Johann in Tyrol, Department of Orthopedic Surgery, St. Johann in Tyrol (Austria)

    2015-06-01

    To assess diagnostic performance of traction MR arthrography of the hip in detection and grading of chondral and labral lesions with arthroscopic comparison. Seventy-five MR arthrograms obtained ± traction of 73 consecutive patients (mean age, 34.5 years; range, 14-54 years) who underwent arthroscopy were included. Traction technique included weight-adapted traction (15-23 kg), a supporting plate for the contralateral leg, and intra-articular injection of 18-27 ml (local anaesthetic and contrast agent). Patients reported on neuropraxia and on pain. Two blinded readers independently assessed femoroacetabular cartilage and labrum lesions which were correlated with arthroscopy. Interobserver agreement was calculated using κ values. Joint distraction ± traction was evaluated in consensus. No procedure had to be stopped. There were no cases of neuropraxia. Accuracy for detection of labral lesions was 92 %/93 %, 91 %/83 % for acetabular lesions, and 92 %/88 % for femoral cartilage lesions for reader 1/reader 2, respectively. Interobserver agreement was moderate (κ = 0.58) for grading of labrum lesions and substantial (κ = 0.7, κ = 0.68) for grading of acetabular and femoral cartilage lesions. Joint distraction was achieved in 72/75 and 14/75 hips with/without traction, respectively. Traction MR arthrography safely enabled accurate detection and grading of labral and chondral lesions. (orig.)

  14. Magnetic Decoupling Design and Experimental Validation of a Radial-Radial Flux Compound-Structure Permanent-Magnet Synchronous Machine for HEVs

    Directory of Open Access Journals (Sweden)

    Zhiyi Song

    2012-10-01

    Full Text Available The radial-radial flux compound-structure permanent-magnet synchronous machine (CS-PMSM, integrated by two concentrically arranged permanent-magnet electric machines, is an electromagnetic power-splitting device for hybrid electric vehicles (HEVs. As the two electric machines share a rotor as structural and magnetic common part, their magnetic paths are coupled, leading to possible mutual magnetic-field interference and complex control. In this paper, a design method to ensure magnetic decoupling with minimum yoke thickness of the common rotor is investigated. A prototype machine is designed based on the proposed method, and the feasibility of magnetic decoupling and independent control is validated by experimental tests of mutual influence. The CS-PMSM is tested by a designed driving cycle, and functions to act as starter motor, generator and to help the internal combustion engine (ICE operate at optimum efficiency are validated.

  15. Oracle9i database gains traction among leading European customers

    CERN Multimedia

    2002-01-01

    The Oracle Corporation software group, today announced that more than 600 customers worldwide have purchased Oracle9i Real Application Clusters. Some of the European customers include Austrian Railways, BACS, Bavarian Police Force, CERN, e-Spatial, Navision a/s and the North Rhine-Westphalia Police Force.

  16. A case of severe and rigid congenital thoracolumbar lordoscoliosis with diastematomyelia presenting with type 2 respiratory failure: managed by staged correction with controlled axial traction.

    Science.gov (United States)

    Kanagaraju, Vijayanth; Chhabra, H S; Srivastava, Abhishek; Mahajan, Rajat; Kaul, Rahul; Bhatia, Pallav; Tandon, Vikas; Nanda, Ankur; Sangondimath, Gururaj; Patel, Nishit

    2016-10-01

    Congenital lordoscoliosis is an uncommon pathology and its management poses formidable challenge especially in the presence of type 2 respiratory failure and intraspinal anomalies. In such patients standard management protocols are not applicable and may require multistage procedure to minimize risk and optimize results. A 15-year-old girl presented in our hospital emergency services with severe breathing difficulty. She had a severe and rapidly progressing deformity in her back, noted since 6 years of age, associated with severe respiratory distress requiring oxygen and BiPAP support. She was diagnosed to have a severe and rigid congenital right thoracolumbar lordoscoliosis (coronal Cobb's angle: 105° and thoracic lordosis -10°) with type 1 split cord malformation with bony septum extending from T11 to L3. This leads to presentation of restrictive lung disease with type 2 respiratory failure. As her lung condition did not allow for any major procedure, we did a staged procedure rather than executing in a single stage. Controlled axial traction by halogravity was applied initially followed by halo-femoral traction. Four weeks later, this was replaced by halo-pelvic distraction device after a posterior release procedure with asymmetric pedicle substraction osteotomies at T7 and T10. Halo-pelvic distraction continued for 4 more weeks to optimize and correct the deformity. Subsequently definitive posterior stabilization and fusion was done. The detrimental effect of diastematomyelia resection in such cases is clearly evident from literature, so it was left unresected. A good scoliotic correction with improved respiratory function was achieved. Three years follow-up showed no loss of deformity correction, no evidence of pseudarthrosis and a good clinical outcome with reasonably balanced spine. The management of severe and rigid congenital lordoscoliotic deformities with intraspinal anomalies is challenging. Progressive reduction in respiratory volume in untreated

  17. Tire-road friction estimation and traction control strategy for motorized electric vehicle

    Science.gov (United States)

    Jin, Li-Qiang; Yue, Weiqiang

    2017-01-01

    In this paper, an optimal longitudinal slip ratio system for real-time identification of electric vehicle (EV) with motored wheels is proposed based on the adhesion between tire and road surface. First and foremost, the optimal longitudinal slip rate torque control can be identified in real time by calculating the derivative and slip rate of the adhesion coefficient. Secondly, the vehicle speed estimation method is also brought. Thirdly, an ideal vehicle simulation model is proposed to verify the algorithm with simulation, and we find that the slip ratio corresponds to the detection of the adhesion limit in real time. Finally, the proposed strategy is applied to traction control system (TCS). The results showed that the method can effectively identify the state of wheel and calculate the optimal slip ratio without wheel speed sensor; in the meantime, it can improve the accelerated stability of electric vehicle with traction control system (TCS). PMID:28662053

  18. Concept for a Differential Lock and Traction Control Model in Automobiles

    Science.gov (United States)

    Shukul, A. K.; Hansra, S. K.

    2014-01-01

    The automobile is a complex integration of electronics and mechanical components. One of the major components is the differential which is limited due to its shortcomings. The paper proposes a concept of a cost effective differential lock and traction for passenger cars to sports utility vehicles alike, employing a parallel braking mechanism coming into action based on the relative speeds of the wheels driven by the differential. The paper highlights the employment of minimum number of components unlike the already existing systems. The system was designed numerically for the traction control and differential lock for the world's cheapest car. The paper manages to come up with all the system parameters and component costing making it a cost effective system.

  19. METHODOLOGY OF DETERMINATION OF QUALITY INDEX OF MAINTENANCE SERVICE SYSTEM OF POWER EQUIPMENT OF TRACTION SUBSTATIONS

    Directory of Open Access Journals (Sweden)

    O.O. Matusevych

    2016-03-01

    Full Text Available Purpose. The purpose of this paper is development of methodology for definition of a quality system of maintenance and repair (M and P power equipment of traction substations (TS of electrified railways operating under conditions of uncertainty based on expert information. Methodology. The basic tenets of the theory of fuzzy sets and marks, linguistic and interval estimates of experts were applied to solve this problem. Results. Analysis of the existing diversity of approaches to development of modern methods of improvement of M and P allows us to conclude that the improvement in the quality of the system is achieved by solving individual problems increase the operational reliability of power equipment of traction substations in the following main interrelated areas. There are technical, economic and organizational. The basis of the quality evaluation system is initial data and expertise developed version of the document formalized quality evaluation of electrical equipment of traction substations by experts. The choice of determining the level of Quality service system based on the marks, linguistic and interval estimates of experts, which are reflected in quantitative and / or qualitative form was done. The possible options for expert data presentation and their corresponding quantitative methods of calculating the integral index of quality improvement system maintenance and P of traction substations were described. The methodology and the method of assessing the quality of system maintenance and P of TS allows quickly respond to changing operating conditions of power equipment of traction substations, and to determine the most effective strategies for maintenance of electrical and P TS under conditions of uncertainty functioning distance electricity. Originality. The method of a systematic approach to improve the quality of the system maintenance and P of power equipment of traction substation under conditions of uncertainty based on expert

  20. Model-based traction force microscopy reveals differential tension in cellular actin bundles.

    Science.gov (United States)

    Soiné, Jérôme R D; Brand, Christoph A; Stricker, Jonathan; Oakes, Patrick W; Gardel, Margaret L; Schwarz, Ulrich S

    2015-03-01

    Adherent cells use forces at the cell-substrate interface to sense and respond to the physical properties of their environment. These cell forces can be measured with traction force microscopy which inverts the equations of elasticity theory to calculate them from the deformations of soft polymer substrates. We introduce a new type of traction force microscopy that in contrast to traditional methods uses additional image data for cytoskeleton and adhesion structures and a biophysical model to improve the robustness of the inverse procedure and abolishes the need for regularization. We use this method to demonstrate that ventral stress fibers of U2OS-cells are typically under higher mechanical tension than dorsal stress fibers or transverse arcs.

  1. Operation analysis of AC traction motors in terms of electromagnetic torque capability on sustainable railway vehicles

    OpenAIRE

    Bulucea Cornelia A.; Nicola Doru A.; Rosen Marc A.; Mastorakis Nikos E.; Bulucea Carmen A.

    2016-01-01

    Sustainable operation of electric railway systems represents a significant purpose nowadays in the development of high power and high speed locomotives and trains. At present, high speed electric vehicles mostly work with three-phase induction motors or three-phase synchronous motors as traction motors. The two electric machine types have different efficiencies at different operation points, and experience differences with respect to safety, speed and power, energy use and exergy efficiency. ...

  2. Lateral femoral traction pin entry: risk to the femoral artery and other medial neurovascular structures

    Directory of Open Access Journals (Sweden)

    Appleton Paul

    2010-01-01

    Full Text Available Abstract Background Femoral skeletal traction assists in the reduction and transient stabilization of pelvic, acetabular, hip, and femoral fractures when splinting is ineffective. Traditional teaching has recommended a medial entry site for insertion of the traction pin in order to minimize injury to the femoral artery as it passes through Hunter's canal. The present anatomical study evaluates the risk to the femoral artery and other medial neurovascular structures using a lateral entry approach. Methods Six embalmed cadavers (twelve femurs were obtained for dissection. Steinman pins were drilled from lateral to medial at the level of the superior pole of the patella, at 2 cm, and at 4 cm proximal to this point. Medial superficial dissection was then performed to identify the saphenous nerve, the superior medial geniculate artery, the adductor hiatus, the tendinous insertion of the adductor magnus and the femoral artery. Measurements localizing these anatomic structures relative to the pins were obtained. Results The femoral artery was relatively safe and was no closer than 29.6 mm (mean from any of the three Steinman pins. The superior medial geniculate artery was the medial structure at most risk. Conclusions Lateral femoral traction pin entry is a safe procedure with minimal risk to the saphenous nerve and femoral artery. Of the structures examined, only the superior medial geniculate artery is at a risk of iatrogenic injury due to its position. The incidence of such injury in clinical practice and its clinical significance is not known. Lateral insertion facilitates traction pin placement since it minimizes the need to move the contralateral extremity out of the way of the drilling equipment or the need to elevate or externally rotate the injured extremity relative to the contralateral extremity.

  3. A Traction Control Strategy with an Efficiency Model in a Distributed Driving Electric Vehicle

    OpenAIRE

    Lin, Cheng; Cheng, Xingqun

    2014-01-01

    Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the tw...

  4. A dynamic traction splint for the management of extrinsic tendon tightness.

    Science.gov (United States)

    Dovelle, S; Heeter, P K; Phillips, P D

    1987-02-01

    The dynamic traction splint designed by therapists at Walter Reed Army Medical Center is used for the management of extrinsic extensor tendon tightness commonly seen in brachial plexus injuries and traumatic soft tissue injuries of the upper extremity. The two components of the splint allow for simultaneous maximum flexion of the MCP and IP joints. This simple and economical splint provides an additional modality to any occupational therapy service involved in the management of upper extremity disorders.

  5. Strategies for Proximal Femoral Nailing of Unstable Intertrochanteric Fractures: Lateral Decubitus Position or Traction Table.

    Science.gov (United States)

    Sonmez, Mesut Mehmet; Camur, Savas; Erturer, Erden; Ugurlar, Meric; Kara, Adnan; Ozturk, Irfan

    2017-03-01

    The aim of this prospective randomized study was to compare the traction table and lateral decubitus position techniques in the management of unstable intertrochanteric fractures. Eighty-two patients with unstable intertrochanteric fractures between 2011 and 2013 were included in this study. All patients were treated surgically with the Proximal Femoral Nail Antirotation implant (DePuy Synthes). Patients were randomized to undergo the procedure in the lateral decubitus position (42 patients) or with the use of a traction table (40 patients). Patients whose procedure was not performed entirely with a semi-invasive method or who required the use of additional fixation materials, such as cables, were excluded from the study. The groups were compared on the basis of the setup time, surgical time, fluoroscopic exposure time, tip-to-apex distance, collodiaphyseal angle, and modified Baumgaertner criteria for radiologic reduction. The setup time, surgical time, and fluoroscopic exposure time were lower and the differences were statistically significant in the lateral decubitus group compared with the traction table group. The collodiaphyseal angles were significantly different between the groups in favor of the lateral decubitus method. The tip-to-apex distance and the classification of reduction according to the modified Baumgaertner criteria did not demonstrate a statistically significant difference between the groups. The lateral decubitus position is used for most open procedures of the hip. We found that this position facilitates exposure for the surgical treatment of unstable intertrochanteric fractures and has advantages over the traction table in terms of set up time, surgical time and fluoroscopic exposure time.

  6. [The use of Saunders lumbar traction in physiotherapy of patients with chronic lower back pain].

    Science.gov (United States)

    Pingot, Julia; Pingot, Mariusz; Łabecka, Monika; Woldańska-Okońska, Marta

    2014-05-01

    Pain of the lower back is one of the most common ailments in modem society. Such frequent occurrence of back pain syndromes is a serious medical and social problem. Despite numerous attempts, there have not been comprehensive or decisive publications on the therapeutic standard for back pain syndromes that would cover all the aspects of the ailment. Partial report can change the attitude and shed new light on the treatment of these syndromes. The aim of this study was to evaluate the use of Saunders lumbar tractions in patients with chronic lower back pain in comparison with the group of patients undergoing pharmacological treatment. The study included 140 patients with chronic lower back pain who were divided into two groups. Each group consisted of 70 persons of mixed gender (the age mean value was 45). Group I were treated with the use of Saunders lumbar traction and Group II (control group) were treated pharmacologically. The following scales were used to assess pain and mobility of the lumbar part of the vertebral column (before treatment, in-treatment, right after treatment and 30 days after treatment): Laitinen, VAS, Rolland-Morris questionnaire and Schober functional test. The statistical analysis was performed with Greenhouse-Geisser test of within-subjects effects. In both the groups, a significant analgesic action and an improvement to spinal mobility were observed. Significantly better results were obtained in Group I where the patients had been treated with the use of Saunders lumbar traction. The pharmacological treatment applied in Group II showed an analgesic action and influenced positively the functional parameters of the patients. The effects, however, were much worse than in Group 1 where axial Saunders traction was applied to the lumbar part of the vertebral column.

  7. Creep force modelling for rail traction vehicles based on the Fastsim algorithm

    Science.gov (United States)

    Spiryagin, Maksym; Polach, Oldrich; Cole, Colin

    2013-11-01

    The evaluation of creep forces is a complex task and their calculation is a time-consuming process for multibody simulation (MBS). A methodology of creep forces modelling at large traction creepages has been proposed by Polach [Creep forces in simulations of traction vehicles running on adhesion limit. Wear. 2005;258:992-1000; Influence of locomotive tractive effort on the forces between wheel and rail. Veh Syst Dyn. 2001(Suppl);35:7-22] adapting his previously published algorithm [Polach O. A fast wheel-rail forces calculation computer code. Veh Syst Dyn. 1999(Suppl);33:728-739]. The most common method for creep force modelling used by software packages for MBS of running dynamics is the Fastsim algorithm by Kalker [A fast algorithm for the simplified theory of rolling contact. Veh Syst Dyn. 1982;11:1-13]. However, the Fastsim code has some limitations which do not allow modelling the creep force - creep characteristic in agreement with measurements for locomotives and other high-power traction vehicles, mainly for large traction creep at low-adhesion conditions. This paper describes a newly developed methodology based on a variable contact flexibility increasing with the ratio of the slip area to the area of adhesion. This variable contact flexibility is introduced in a modification of Kalker's code Fastsim by replacing the constant Kalker's reduction factor, widely used in MBS, by a variable reduction factor together with a slip-velocity-dependent friction coefficient decreasing with increasing global creepage. The proposed methodology is presented in this work and compared with measurements for different locomotives. The modification allows use of the well recognised Fastsim code for simulation of creep forces at large creepages in agreement with measurements without modifying the proven modelling methodology at small creepages.

  8. Design of master control unit for laboratory prototype of traction converter for locomotives

    OpenAIRE

    Žák, Jan; Peroutka, Zdeněk; Ovaska, Seppo J.

    2008-01-01

    This paper deals with the prototype of a main traction converter with medium-frequency transformer for AC trolley wire-fed locomotives. The attention is paid to the new master control and diagnostic unit. The designed master control unit has been implemented in the LabVIEW environment. Our master control unit ensures an effective human interface between a user and the control hardware. In this case, the master unit makes possible both extensive control and diagnostic operations of the laborat...

  9. Innovative multi system traction equipment for modern rail vehicles; Innovative Mehrsystem-Antriebsausruestung fuer moderne Triebzuege

    Energy Technology Data Exchange (ETDEWEB)

    Guggisberg, B.; Daehler, P. [ABB Schweiz AG, Turgi (Switzerland)

    2007-07-01

    The BORDLINE-Compact Converter consists of a main traction converter with integrated auxiliary converter. The converters are equipped with low voltage semiconductors and are intended to be used in DMUs as well as in EMUs with overhead voltages of 15 kV or 25 kV. For the operation with 3 kV DC an additional DC to AC converter using a separate main transformer winding is installed. (orig.)

  10. MODELING OF THE CONTROLLED TRACTION POWER SUPPLY SYSTEM IN THE SPACE-TIME COORDINATES

    Directory of Open Access Journals (Sweden)

    Dmitry BOSYI

    2017-09-01

    Full Text Available The problems of the traction power supply system calculation are considered in the article. The authors proposed the space-time model, which is based on the analytical functions of the current- and voltage-drop distributions in the contact network. The usage of the proposed model is shown for the control law calculation both to stabilize the voltage at the pantographs of the electric rolling stocks and to reduce the power losses.

  11. le traitement chirurgical des poches de rétraction tympaniques

    African Journals Online (AJOL)

    16 juin 2006 ... L'évolution naturelle de l'otite atelectasique vers la maladie cholestéatomateuse complique d'avantage la prise en charge des poches de rétraction. ... risque de cholestéatome résiduel était important. Après un recul minimum de 21 mois, le résultat anato- mique été satisfaisant dans 88%. Ailleurs ...

  12. A comparative study on OCT before and after the operation for vitreomacular traction syndrome

    Directory of Open Access Journals (Sweden)

    Shu-Qi Song

    2017-07-01

    Full Text Available AIM: To make a contrast and then analyze the difference of optical coherence tomography(OCTbefore and after vitreomacular traction syndrome(VTSwas performed. METHODS: The clinical date of 11 evaluable eyes of 11 patients with VTS who were diagnosed by OCT and underwent 25G vitreous surgery from January 2013 to January 2014 were retrospectively analyzed. Patients were followed up for an average of 6mo, to observe the visual acuity and OCT examination of the patient before and after operation. We compared the changes of retinal thickness and local morphology before and after operation.RESULTS: After vitreous retraction, 6 eyes improved, 2 eyes do not improve. One eye received macular membrane traction, in the operation the macular epiretinal membrane peeling, retrial membrane stripping and the triamcinolone acetonide intravitreal injection were given, but after the operation, the vision does not improve. Two eyes received vitreous combined with retinal macular membrane traction. In the operation, macular epiretinal membrane stripping was given, after the operation, visual acuity improved. The proportion of those with visual acuity of 0.1 or more increased from 46% before to 73% after the operation. Before operations, the mean central macular thickness was 619.27±195.13μm, 239.12±143.84μm after, which decreased significantly(PCONCLUSION: Vitrectomy can effectively relieve the vitreous traction of the macula, and can prevent further decline in visual acuity and reduce macular edema as well as improve the visual acuity of some patients. So, OCT has important guiding significance on the diagnosis and prognosis of this group.

  13. A semi-implicit augmented IIM for Navier-Stokes equations with open, traction, or free boundary conditions.

    Science.gov (United States)

    Li, Zhilin; Xiao, Li; Cai, Qin; Zhao, Hongkai; Luo, Ray

    2015-08-15

    In this paper, a new Navier-Stokes solver based on a finite difference approximation is proposed to solve incompressible flows on irregular domains with open, traction, and free boundary conditions, which can be applied to simulations of fluid structure interaction, implicit solvent model for biomolecular applications and other free boundary or interface problems. For some problems of this type, the projection method and the augmented immersed interface method (IIM) do not work well or does not work at all. The proposed new Navier-Stokes solver is based on the local pressure boundary method, and a semi-implicit augmented IIM. A fast Poisson solver can be used in our algorithm which gives us the potential for developing fast overall solvers in the future. The time discretization is based on a second order multi-step method. Numerical tests with exact solutions are presented to validate the accuracy of the method. Application to fluid structure interaction between an incompressible fluid and a compressible gas bubble is also presented.

  14. A semi-implicit augmented IIM for Navier–Stokes equations with open, traction, or free boundary conditions

    Science.gov (United States)

    Li, Zhilin; Xiao, Li; Cai, Qin; Zhao, Hongkai; Luo, Ray

    2016-01-01

    In this paper, a new Navier–Stokes solver based on a finite difference approximation is proposed to solve incompressible flows on irregular domains with open, traction, and free boundary conditions, which can be applied to simulations of fluid structure interaction, implicit solvent model for biomolecular applications and other free boundary or interface problems. For some problems of this type, the projection method and the augmented immersed interface method (IIM) do not work well or does not work at all. The proposed new Navier–Stokes solver is based on the local pressure boundary method, and a semi-implicit augmented IIM. A fast Poisson solver can be used in our algorithm which gives us the potential for developing fast overall solvers in the future. The time discretization is based on a second order multi-step method. Numerical tests with exact solutions are presented to validate the accuracy of the method. Application to fluid structure interaction between an incompressible fluid and a compressible gas bubble is also presented. PMID:27087702

  15. Demagnetization monitoring and life extending control for permanent magnet-driven traction systems

    Science.gov (United States)

    Niu, Gang; Liu, Senyi

    2018-03-01

    This paper presents a novel scheme of demagnetization monitoring and life extending control for traction systems driven by permanent magnet synchronous motors (PMSMs). Firstly, the offline training is carried to evaluate fatigue damage of insulated gate bipolar transistors (IGBTs) under different flux loss based on first-principle modeling. Then an optimal control law can be extracted by turning down the power distribution factor of the demagnetizing PMSM until all damages of IGBTs turn to balance. Next, the similarity-based empirical modeling is employed to online estimate remaining flux of PMSMs, which is used to update the power distribution factor by referring the optimal control law for the health-oriented autonomous control. The proposed strategy can be demonstrated by a case study of traction drive system coupled with dual-PMSMs. Compared with traditional control strategy, the results show that the novel scheme can not only guarantee traction performance but also extend remaining useful life (RUL) of the system after suffering demagnetization fault.

  16. Morphostructural characterization of soil conventionally tilled with mechanized and animal traction with and without cover crop

    Directory of Open Access Journals (Sweden)

    Ricardo Ralisch

    2010-12-01

    Full Text Available The structural stability and restructuring ability of a soil are related to the methods of crop management and soil preparation. A recommended strategy to reduce the effects of soil preparation is to use crop rotation and cover crops that help conserve and restore the soil structure. The aim of this study was to evaluate and quantify the homogeneous morphological units in soil under conventional mechanized tillage and animal traction, as well as to assess the effect on the soil structure of intercropping with jack bean (Canavalia ensiformis L.. Profiles were analyzed in April of 2006, in five counties in the Southern-Central region of Paraná State (Brazil, on family farms producing maize (Zea mays L., sometimes intercropped with jack bean. The current structures in the crop profile were analyzed using Geographic Information Systems (GIS and subsequently principal component analysis (PCA to generate statistics. Morphostructural soil analysis showed a predominance of compact units in areas of high-intensity cultivation under mechanized traction. The cover crop did not improve the structure of the soil with low porosity and compact units that hamper the root system growth. In areas exposed to animal traction, a predominance of cracked units was observed, where roots grew around the clods and along the gaps between them.

  17. A case of traction retinal detachment in a patient with Gaucher disease.

    Science.gov (United States)

    Watanabe, Akira; Gekka, Tamaki; Arai, Kota; Tsuneoka, Hiroshi

    2017-01-01

    This is the first report of vitreous surgery for traction retinal detachment in a patient with type III Gaucher disease with multiple vitreous opacities. A 16-year-old boy who was diagnosed with Gaucher disease at age two and was undergoing enzyme replacement therapy presented with numerous white opacities of varying sizes in the vitreous bodies of both eyes. Visual acuity was 20/40 in the right eye and 20/2000 in the left eye. The retina of the left eye was completely detached, and vitreous surgery was performed. Liquefaction of the vitreous body was advanced, and the central part of the vitreous cavity contained almost no vitreous humor. The macular region was successfully aspirated with a vitreous cutter to form a posterior vitreous detachment. From the optic disk to the nasal side, however, posterior vitreous detachment formation was prevented by strong adhesions between the retina and the vitreous body. The traction retinal detachment of the posterior fundus improved after vitreous body resection alone. Traction retinal detachment may occur as a result of severe vitreous liquefaction in cases of Gaucher disease with numerous vitreous opacities.

  18. Investigation of wear of insulation of traction engines of locomotives in operation

    Directory of Open Access Journals (Sweden)

    Nefedov Roman

    2018-01-01

    Full Text Available The article analyzes reliability of traction electric motors in operation. It is shown that the greatest number of failure falls on the winding of the armature. Investigation of the causes of increased wear of the armature winding insulation was carried out using the dynamic thermal model of the electric motor. The model is represented by 150 final elements and takes into account the conditions of thermal conductivity between the nodes and heat transfer to the cooling air. Verification of the model was carried out by comparison with the results of thermal tests of electric motors of the series HБ-406 and ЭД-118. The field of temperatures in the traction motor under various loads was investigated. It is shown that in stationary mode the temperature change along the armature winding can reach 60C. Modeling of thermal dynamic processes in the engine during its operation on the locomotive allowed to identify the most stressed nodes. It is shown that the resource of the electric motor is determined by the wear of the insulation of the frontal part of the armature winding on the side of the traction drive of the locomotive.

  19. Degradation-mediated cellular traction directs stem cell fate in covalently crosslinked three-dimensional hydrogels

    Science.gov (United States)

    Khetan, Sudhir; Guvendiren, Murat; Legant, Wesley R.; Cohen, Daniel M.; Chen, Christopher S.; Burdick, Jason A.

    2013-05-01

    Although cell-matrix adhesive interactions are known to regulate stem cell differentiation, the underlying mechanisms, in particular for direct three-dimensional encapsulation within hydrogels, are poorly understood. Here, we demonstrate that in covalently crosslinked hyaluronic acid (HA) hydrogels, the differentiation of human mesenchymal stem cells (hMSCs) is directed by the generation of degradation-mediated cellular traction, independently of cell morphology or matrix mechanics. hMSCs within HA hydrogels of equivalent elastic moduli that permit (restrict) cell-mediated degradation exhibited high (low) degrees of cell spreading and high (low) tractions, and favoured osteogenesis (adipogenesis). Moreover, switching the permissive hydrogel to a restrictive state through delayed secondary crosslinking reduced further hydrogel degradation, suppressed traction, and caused a switch from osteogenesis to adipogenesis in the absence of changes to the extended cellular morphology. Furthermore, inhibiting tension-mediated signalling in the permissive environment mirrored the effects of delayed secondary crosslinking, whereas upregulating tension induced osteogenesis even in the restrictive environment.

  20. VITRECTOMY FOR INTERMEDIATE AGE-RELATED MACULAR DEGENERATION ASSOCIATED WITH TANGENTIAL VITREOMACULAR TRACTION: A CLINICOPATHOLOGIC CORRELATION.

    Science.gov (United States)

    Ziada, Jean; Hagenau, Felix; Compera, Denise; Wolf, Armin; Scheler, Renate; Schaumberger, Markus M; Priglinger, Siegfried G; Schumann, Ricarda G

    2018-03-01

    To describe the morphologic characteristics of the vitreomacular interface in intermediate age-related macular degeneration associated with tangential traction due to premacular membrane formation and to correlate with optical coherence tomography (OCT) findings and clinical data. Premacular membrane specimens were removed sequentially with the internal limiting membrane from 27 eyes of 26 patients with intermediate age-related macular degeneration during standard vitrectomy. Specimens were processed for immunocytochemical staining of epiretinal cells and extracellular matrix components. Ultrastructural analysis was performed using transmission electron microscopy. Spectral domain optical coherence tomography images and patient charts were evaluated in retrospect. Immunocytochemistry revealed hyalocytes and myofibroblasts as predominant cell types. Ultrastructural analysis demonstrated evidence of vitreoschisis in all eyes. Myofibroblasts with contractile properties were observed to span between folds of the internal limiting membrane and vitreous cortex collagen. Retinal pigment epithelial cells or inflammatory cells were not detected. Mean visual acuity (Snellen) showed significant improvement from 20/72 ± 20/36 to 20/41 ± 20/32 (P age-related macular degeneration predominantly consists of vitreous collagen, hyalocytes, and myofibroblasts with contractile properties. Vitreoschisis and vitreous-derived cells appear to play an important role in traction formation of this subgroup of eyes. In patients with intermediate age-related macular degeneration and contractile premacular membrane, release of traction by vitrectomy with internal limiting membrane peeling results in significantly functional and anatomical improvement.

  1. Investigation of efficiency of electric drive control system of excavator traction mechanism based on feedback on load

    Science.gov (United States)

    Kuznetsov, N. K.; Iov, I. A.; Iov, A. A.

    2018-05-01

    The article presents the results of a study of the efficiency of the electric drive control system of the traction mechanism of a dragline based on the use of feedback on load in the traction cable. The investigations were carried out using a refined electromechanical model of the traction mechanism, which took into account not only the elastic elements of the gearbox, the backlashes in it and the changes in the kinematic parameters of the mechanism during operation, but also the mechanical characteristics of the electric drive and the features of its control system. By mathematical modeling of the transient processes of the electromechanical system, it is shown that the introduction of feedback on the load in the elastic element allows one to reduce the dynamic loads in the traction mechanism and to limit the elastic oscillations of the actuating mechanism in comparison with the standard control system. Fixed as a general decrease in the dynamic load of the nodes of traction mechanism in the modes of loading and latching of the bucket, and a decrease the operating time of the mechanism at maximum load. At the same time, undesirable phenomena in the operation of the electric drive were also associated with the increase in the recovery time of the steady-state value of the speed of the actuating mechanism under certain operating conditions, which can lead to a decrease in the reliability of the mechanical part and the productivity of the traction mechanism.

  2. Vehicle non-exhaust emissions from the tyre-road interface - effect of stud properties, traction sanding and resuspension

    Science.gov (United States)

    Kupiainen, Kaarle J.; Pirjola, Liisa

    2011-08-01

    In Northern cities respirable street dust emission levels (PM 10) are especially high during spring. The spring time dust has been observed to cause health effects as well as discomfort among citizens. Major sources of the dust are the abrasion products from the pavement and traction sand aggregates that are formed due to the motion of the tyre. We studied the formation of respirable abrasion particles in the tyre-road interface due to tyre studs and traction sanding by a mobile laboratory vehicle Sniffer. The measurements were preformed on a test track, where the influence of varying stud weight and stud number per tyre on PM 10 emissions was studied. Studded tyres resulted in higher emission levels than studless tyres especially with speeds 50 km h -1 and higher; however, by using light weight studs, which approximately halves the weight of studs, or by reducing the number of studs per tyre to half, the emission levels decreased by approximately half. Additionally measurements were done with and without traction sand coverage on the pavement of a public road. After traction sanding the emission levels were not affected by tyre type but by formation and suspension of traction sand related dust from the road surface. The emissions after traction sanding decreased as a function of time as passing vehicles' motion shifted the sand grains away from the areas with most tyre-road contact.

  3. Cell origami: self-folding of three-dimensional cell-laden microstructures driven by cell traction force.

    Directory of Open Access Journals (Sweden)

    Kaori Kuribayashi-Shigetomi

    Full Text Available This paper describes a method of generating three-dimensional (3D cell-laden microstructures by applying the principle of origami folding technique and cell traction force (CTF. We harness the CTF as a biological driving force to fold the microstructures. Cells stretch and adhere across multiple microplates. Upon detaching the microplates from a substrate, CTF causes the plates to lift and fold according to a prescribed pattern. This self-folding technique using cells is highly biocompatible and does not involve special material requirements for the microplates and hinges to induce folding. We successfully produced various 3D cell-laden microstructures by just changing the geometry of the patterned 2D plates. We also achieved mass-production of the 3D cell-laden microstructures without causing damage to the cells. We believe that our methods will be useful for biotechnology applications that require analysis of cells in 3D configurations and for self-assembly of cell-based micro-medical devices.

  4. Cell origami: self-folding of three-dimensional cell-laden microstructures driven by cell traction force.

    Science.gov (United States)

    Kuribayashi-Shigetomi, Kaori; Onoe, Hiroaki; Takeuchi, Shoji

    2012-01-01

    This paper describes a method of generating three-dimensional (3D) cell-laden microstructures by applying the principle of origami folding technique and cell traction force (CTF). We harness the CTF as a biological driving force to fold the microstructures. Cells stretch and adhere across multiple microplates. Upon detaching the microplates from a substrate, CTF causes the plates to lift and fold according to a prescribed pattern. This self-folding technique using cells is highly biocompatible and does not involve special material requirements for the microplates and hinges to induce folding. We successfully produced various 3D cell-laden microstructures by just changing the geometry of the patterned 2D plates. We also achieved mass-production of the 3D cell-laden microstructures without causing damage to the cells. We believe that our methods will be useful for biotechnology applications that require analysis of cells in 3D configurations and for self-assembly of cell-based micro-medical devices.

  5. Análise radiográfica da coluna cervical em indivíduos assintomáticos submetidos a tração manual Radiographic analysis of the cervical spine in healthy individuals submitted to manual traction

    Directory of Open Access Journals (Sweden)

    Roger Burgo de Souza

    2008-08-01

    Full Text Available OBJETIVO: Avaliar, radiograficamente, o efeito da tração manual sobre o comprimento da coluna cervical. MATERIAIS E MÉTODOS: Cinqüenta e cinco participantes de ambos os gêneros - 12 masculinos (22% e 43 femininos (78% - sem história de distúrbios cervicais contituíram a amostra deste estudo. Eles foram submetidos a dois procedimentos radiológicos, um antes e outro durante a tração manual sustentada por 120 segundos. As distâncias entre as bordas anteriores e posteriores da segunda à sétima vértebras cervicais foram mensuradas e comparadas antes e durante a tração manual. RESULTADOS: A mediana da distância anterior antes da tração foi de 8,40 cm e durante a tração aumentou para 8,50 cm (p=0,002. A mediana da distância posterior antes da tração foi de 8,35 cm e durante a tração aumentou para 8,50 cm (pOBJECTIVE: To evaluate radiographically the effect of manual traction on the length of the cervical spine in healthy individuals. MATERIALS AND METHODS: The sample of the present study included 55 individuals - 12 men (22% and 43 women (78% - with no previous history of cervical disorders, submitted to two radiological procedures previously and during manual traction sustained for 120 seconds. Distances between the anterior and posterior edges from the second to the seventh cervical vertebrae were measured and compared before and during manual traction. RESULTS: The median of pre-traction anterior length was 8.40 cm, increasing to 8.50 cm during the traction (p=0.002; and the median of pre-traction posterior length was 8.35 cm, increasing to 8.50 cm during traction (p<0.001. CONCLUSION: Application of manual traction resulted in a statistically significant increase in the length the cervical spine in healthy individuals.

  6. Perfluorocarbon-perfused 23 gauge three-dimensional vitrectomy for complicated diabetic tractional retinal detachment

    Science.gov (United States)

    Velez-Montoya, Raul; Guerrero-Naranjo, Jose Luis; Garcia-Aguirre, Gerardo; Morales-Cantón, Virgilio; Fromow-Guerra, Jans; Quiroz-Mercado, Hugo

    2011-01-01

    Background Perfluorocarbon liquid (PCL)-perfused vitrectomy has been shown in previous studies to be feasible, safe, and to have advantages in managing complicated cases of tractional retinal detachment. The present study had the objectives of describing the anatomical results and measuring surgical time and PCL consumption when combining PCL-perfused techniques with modern vitrectomy equipment. Methods A prospective, interventional consecutive case series was investigated. We enrolled patients with diabetic tractional retinal detachment, complicated by proliferative vitreoretinopathy and poor vision. A 23 gauge PCL-perfused vitrectomy was done with three-dimensional settings. During the procedure, we assessed the degree of surgical bleeding, visualization quality, and difficulty of membrane dissections. Visual acuity, intraocular pressure, and anatomical success were assessed at one and 3 months of follow-up. Results Twelve patients were enrolled in this study. There were no statistical significant changes in intraocular pressure and visual acuity throughout the follow-up period. Surgery was performed in a hemorrhage-free environment in almost all cases, with good visualization and low technical difficulty. The mean complete surgical time was 94.92 ± 25.03 minutes. The mean effective vitrectomy time was 22.50 ± 19.04 minutes and the mean PCL consumption was 25.08 ± 9.76 mL, with a speed of 1.11 mL/minute. Anatomical success was 67% at 3 months. Conclusion Although the technique proved to have some advantages in managing complicated cases of diabetic tractional retinal detachment, there was a high consumption of PCL. A redesign of the entire system is needed in order to decrease the amount of PCL needed for the technique. PMID:22267907

  7. Cohesive traction-separation relations for plate tearing under mixed mode loading

    DEFF Research Database (Denmark)

    Andersen, R. G.; Woelke, P. B.; Nielsen, K. L.

    2018-01-01

    The present study investigates a sequence of failure events related to steady-state tearing of large-scale ductile plates by employing the micro-mechanics based Gurson-Tvergaard-Needleman (GTN) model. The fracture process in front of an advancing crack is approximated by a series of 2D plane strain...... finite element models to facilitate a comprehensive study of mixed mode fracture behavior as well as a parameter study of the cohesive energy and tractions involved in the process. The results from the conducted GTN model simulations are used to define cohesive zone models suitable for plate tearing...

  8. Coupled electromagnetic acoustic and thermal-flow modeling of an induction motor of railway traction

    International Nuclear Information System (INIS)

    Fasquelle, A.; Le Besnerais, J.; Harmand, S.; Hecquet, M.; Brisset, S.; Brochet, P.; Randria, A.

    2010-01-01

    In order to optimize the design of an enclosed induction machine of railway traction, a multi-physical model is developed taking into account electromagnetic, mechanical and thermal-flow phenomena. The electromagnetic model is based on analytical formulations and allows calculating the losses. The thermal-flow modeling is based on an equivalent thermal circuit which has the feature to consider the flow structure inside the machine. In this way, a numerical study has been carried out to evaluate this internal flow structure depending on the rotational speed. The results of the multi-physical model are confronted with experimental results.

  9. Equivalent model and power flow model for electric railway traction network

    Science.gov (United States)

    Wang, Feng

    2018-05-01

    An equivalent model of the Cable Traction Network (CTN) considering the distributed capacitance effect of the cable system is proposed. The model can be divided into 110kV side and 27.5kV side two kinds. The 110kV side equivalent model can be used to calculate the power supply capacity of the CTN. The 27.5kV side equivalent model can be used to solve the voltage of the catenary. Based on the equivalent simplified model of CTN, the power flow model of CTN which involves the reactive power compensation coefficient and the interaction of voltage and current, is derived.

  10. Electric traction motion power and energy supply : basics and practical experience

    CERN Document Server

    Steimel, Andreas

    2011-01-01

    This book has evolved from the lecture series ""Elektrische Bahnen" (""Electric railways") which has been held at Ruhr-Universität Bochum since 1996. Its primary audience are students of electrical energy technologies, control engineering and mechanical engineering as well as young engineers of electrical engineering, especially in the fields of power electronics, in railway industry and in railway-operating companies. The book intends to convey mechanical fundamentals of electric railway propulsion, which includes rail-bound guidance, transmission of traction effort from wheel to rail under t

  11. Behavior of single lap composite bolted joint under traction loading: Experimental investigation

    Science.gov (United States)

    Awadhani, L. V.; Bewoor, Anand

    2018-04-01

    Composite bolted joints are preferred connection in the composite structures to facilitate the dismantling for the replacements/ maintenance work. The joint behavior under tractive forces has been studied in order to understand the safety of the structure designed. The main objective of this paper is to investigate the behavior of single-lap joints in carbon fiber reinforced epoxy composites under traction loading conditions. The experiments were designed to identify the effect of bolt diameter, stacking sequence and loading rate on the properties of the joint. The experimental results show that the parameters influence the joint performance significantly.

  12. System design of the traction power supply for the high-speed line Beijing - Tianjin

    Energy Technology Data Exchange (ETDEWEB)

    Altmann, Martin; Fischer, Andreas; Tornow, Torsten [Siemens AG, Erlangen (Germany)

    2011-11-15

    The high-speed line Beijing - Tianjin connecting the Capital Beijing with the harbour city Tianjin is the first high-speed line in China dedicated only to passenger traffic and is operated at 300 km/h. The commercial service started in due time for the Olympic games in 2008. For the system design and a reliable traction power supply the simulation software Sitras {sup registered} Sidytrac was used. The program incorporates all modules necessary for the overall system design and relating detailed investigations. Measurements during system integration test validated the simulation results. (orig.)

  13. Integrated Traction Control Strategy for Distributed Drive Electric Vehicles with Improvement of Economy and Longitudinal Driving Stability

    Directory of Open Access Journals (Sweden)

    Xudong Zhang

    2017-01-01

    Full Text Available This paper presents an integrated traction control strategy (ITCS for distributed drive electric vehicles. The purpose of the proposed strategy is to improve vehicle economy and longitudinal driving stability. On high adhesion roads, economy optimization algorithm is applied to maximize motors efficiency by means of the optimized torque distribution. On low adhesion roads, a sliding mode control (SMC algorithm is implemented to guarantee the wheel slip ratio around the optimal slip ratio point to make full use of road adhesion capacity. In order to avoid the disturbance on slip ratio calculation due to the low vehicle speed, wheel rotational speed is taken as the control variable. Since the optimal slip ratio varies according to different road conditions, Bayesian hypothesis selection is utilized to estimate the road friction coefficient. Additionally, the ITCS is designed for combining the vehicle economy and stability control through three traction allocation cases: economy-based traction allocation, pedal self-correcting traction allocation and inter-axles traction allocation. Finally, simulations are conducted in CarSim and Matlab/Simulink environment. The results show that the proposed strategy effectively reduces vehicle energy consumption, suppresses wheels-skid and enhances the vehicle longitudinal stability and dynamic performance.

  14. [Long-Term Outcomes of the Treatment of Pediatric Femoral Shaft Fractures Treated with Bryant's Vertical Traction].

    Science.gov (United States)

    Urban, J; Toufar, P; Kloub, M

    2017-01-01

    PURPOSE OF THE STUDY The paper aimed to evaluate the long-term outcomes of the treatment of diaphyseal femur fractures in children treated with Bryant's vertical traction. Moreover, we also assessed the size of overgrowth in the injured femur. MATERIAL AND METHODS The study included 23 patients with 23 femoral shaft fractures treated with Bryant's vertical traction at our department in 2009-2014. The following parameters were assessed: sex, ïnjured side, weight, age, mechanism of injury, potential abuse, type of fracture, duration of traction, and total length of hospital stay. The healing time of the fracture was the same as the duration of traction. Also assessed was the size of femoral shortening after the removal of traction, the presence of skin complications in the course of treatment and potential development of compartment syndrome. At the mean follow-up of 47.8 months (range 22-85 months) from the date of injury the patients were evaluated clinically and radiologically for: length of limbs, presence of rotational deformity, range of motion of knee and hip joints, potential pain or limping, potential scoliosis of the spine and presence of scars after traction. Finally, through a questionnaire we learned about the opinions of parents as to the treatment method and about the possibility of home traction. RESULTS All the fractures healed. There was a total of 17 injured boys and 6 injured girls. Whereas 12 patients sustained a fracture of the left femur, 11 patients sustained a fracture of the right femur. The mean weight of patients at the time of injury was 13.9 kg (range 5-20 kg). The mean age at the time of traction was 30.8 months (range 1-70 months). The injury most frequently occurred from various falls, altogether in 15 cases (65.2%). Traffic accidents were registered as the cause of injury in 3 cases (13%). No abuse was confirmed. The average duration of traction was 19.8 days (range 8-26 days). The total length of hospital stay took on average 23

  15. Mechanical Hybrid KERS Based on Toroidal Traction Drives: An Example of Smart Tribological Design to Improve Terrestrial Vehicle Performance

    Directory of Open Access Journals (Sweden)

    Francesco Bottiglione

    2013-01-01

    Full Text Available We analyse in terms of efficiency and traction capabilities a recently patented traction drive, referred to as the double roller full-toroidal variator (DFTV. We compare its performance with the single roller full-toroidal variator (SFTV and the single roller half-toroidal variator (SHTV. Modeling of these variators involves challenging tribological issues; the traction and efficiency performances depend on tribological phenomena occurring at the interface between rollers and disks, where the lubricant undergoes very severe elastohydrodynamic lubrication regimes. Interestingly, the DFTV shows an improvement of the mechanical efficiency over a wide range of transmission ratios and in particular at the unit speed ratio as in such conditions in which the DFTV allows for zero-spin, thus strongly enhancing its traction capabilities. The very high mechanical efficiency and traction performances of the DFTV are exploited to investigate the performance of a flywheel-based Kinetic Energy Recovery System (KERS, where the efficiency of the variator plays an important role in determining the overall energy recovery performance. The energy boost capabilities and the round-trip efficiency are calculated for the three different variators considered in this study. The results suggest that the energy recovery potential of the mechanical KERS can be improved with a proper choice of the variator.

  16. [Randomized controlled trials of needle knife therapy combined with rotation traction manipulation for the treatment of cervical spondylotic radiculopathy].

    Science.gov (United States)

    Zhou, Zhong-Liang; Su, Guo-Hong; Zheng, Bao-Zhu; Zuo, Yu-Zhu; Wei, Fu-Liang

    2016-09-25

    To compare the therapeutic effects between needle knife therapy combined with rotation traction manipulation and rotation traction manipulation for the treatment of cervical spondylotic radiculopathy. From November 2013 to June 2015, 80 patients with cervical spondylotic radiculopathy meeting the inclusion criteria were divided into two groups randomly:the control group in which 39 patients were treated with rotation traction manipulation, and the treatment group in which 41 patients were treated with needle knife combined with rotation traction manipulation. The patients in the control group were treated once dayly for 2 weeks, which was 1 course. The patients in the treatment group were treated with needle knife firstly once a week for 2 weeks, which was 1 course;then were treated with the same methods as the patients in the control group. The symptoms, signs score and the therapeutic effects of the two groups before and after treatment were observed. After treatment, symptoms and signs scores declined in both groups( P knife combined with rotation traction manipulation is an effective method for the treatment of cervical spondylotic radiculopathy, which is better than using manipulation method simply. Needle knife therapy has follow advantages:improving local blood circulation, reducing local content of pain substance, increasing production of substances resisting pain, opening channels and collaterals, and make body reaching new static and dynamic balance on the new foundation.

  17. Comparative study between lateral decubitus and traction table for treatment of pertrochanteric fractures with cephalomedullary nails ☆

    Directory of Open Access Journals (Sweden)

    Eric Fernando de Souza

    Full Text Available ABSTRACT OBJECTIVE: To perform a retrospective radiographic assessment of the reduction and implant position in the femoral head in patients with pertrochanteric fractures treated with cephalomedullary nailing in the lateral position versus traction table. METHODS: Radiographs of patients with pertrochanteric fracture of the femur treated with cephalomedullary nailing in the lateral position and traction table were retrospectively evaluated. For the evaluation we used the anteroposterior radiographic view of the pelvis and the lateral view of the affected side. The cervicodiaphyseal angle, the tip-apex distance (TAD, and the spatial position of the cephalic component in the head were measured. Two patient groups were created, one group operated on the traction table and another group operated in the lateral position. RESULTS: Regarding the cervicodiaphyseal angle observed in the traction table group, the results of 11 patients (61.1% were outside the acceptable parameters proposed in the present study. Both groups were equivalent regarding TAD and the position of the cephalic component in the head. CONCLUSION: A difference in the cervicodiaphyseal angle was observed; the group operated on the traction table had 11 patients (61.1% whose measurements were outside the acceptable parameters.

  18. Overhead Bryant's Traction Does Not Improve the Success of Closed Reduction or Limit AVN in Developmental Dysplasia of the Hip.

    Science.gov (United States)

    Sucato, Daniel J; De La Rocha, Adriana; Lau, Karlee; Ramo, Brandon A

    2017-03-01

    Preoperative Bryant's overhead traction before closed reduction (CR) in developmental dysplasia of the hip (DDH) remains controversial and its success in increasing CR rates and reducing avascular necrosis (AVN) rates has not been specifically reported in a large cohort. IRB-approved retrospective study of patients (below 3 y)who were treated with attempted CR for idiopathic DDH from 1980 to 2009. Successful CR was defined as a hip that remained reduced and did not require repeat CR or open reduction. Patients were grouped by age, hip instability [Ortolani positive (reducible) vs. fixed dislocation], and Tonnis classification and rates of successful CR were compared between groups with PAVN between the traction (18%) and no-traction (8%) groups for all patients (P=0.15). In this retrospective series, preoperative Bryant's traction does not improve the rate of a successful CR for patients with DDH and has no protective effect on the development of AVN of the femoral head. These results suggest that Bryant's overhead traction may not be warranted for patients below 3 years of age with DDH. Level III.

  19. Capillary network formation from dispersed endothelial cells: Influence of cell traction, cell adhesion, and extracellular matrix rigidity

    Science.gov (United States)

    Ramos, João R. D.; Travasso, Rui; Carvalho, João

    2018-01-01

    The formation of a functional vascular network depends on biological, chemical, and physical processes being extremely well coordinated. Among them, the mechanical properties of the extracellular matrix and cell adhesion are fundamental to achieve a functional network of endothelial cells, able to fully cover a required domain. By the use of a Cellular Potts Model and Finite Element Method it is shown that there exists a range of values of endothelial traction forces, cell-cell adhesion, and matrix rigidities where the network can spontaneously be formed, and its properties are characterized. We obtain the analytical relation that the minimum traction force required for cell network formation must obey. This minimum value for the traction force is approximately independent on the considered cell number and cell-cell adhesion. We quantify how these two parameters influence the morphology of the resulting networks (size and number of meshes).

  20. Finger-Shaped GelForce: Sensor for Measuring Surface Traction Fields for Robotic Hand.

    Science.gov (United States)

    Sato, K; Kamiyama, K; Kawakami, N; Tachi, S

    2010-01-01

    It is believed that the use of haptic sensors to measure the magnitude, direction, and distribution of a force will enable a robotic hand to perform dexterous operations. Therefore, we develop a new type of finger-shaped haptic sensor using GelForce technology. GelForce is a vision-based sensor that can be used to measure the distribution of force vectors, or surface traction fields. The simple structure of the GelForce enables us to develop a compact finger-shaped GelForce for the robotic hand. GelForce that is developed on the basis of an elastic theory can be used to calculate surface traction fields using a conversion equation. However, this conversion equation cannot be analytically solved when the elastic body of the sensor has a complicated shape such as the shape of a finger. Therefore, we propose an observational method and construct a prototype of the finger-shaped GelForce. By using this prototype, we evaluate the basic performance of the finger-shaped GelForce. Then, we conduct a field test by performing grasping operations using a robotic hand. The results of this test show that using the observational method, the finger-shaped GelForce can be successfully used in a robotic hand.

  1. Therapeutic effects of flurbiprofen axetil on mesenteric traction syndrome: randomized clinical trial.

    Science.gov (United States)

    Takahashi, Hidemasa; Shida, Dai; Tagawa, Kyoko; Iwamoto, Ryo; Arita, Makoto; Arai, Hiroyuki; Suzuki, Takeo

    2017-08-11

    This study aimed to reveal the appropriate timing for the intravenous administration of flurbiprofen axetil for preventing mesenteric traction syndrome (MTS), caused by prostacyclin release. In this prospective, randomized, clinical study, forty-five patients who were undergoing elective surgery for colorectal cancer via laparotomy were enrolled. Patients were randomly divided into 3 groups: a preoperative group (n = 16) receiving flurbiprofen axetil directly before surgery; a post-MTS group (n = 14) receiving following MTS onset; and a control group (n = 15) who were not administered flurbiprofen axetil. 6-keto-PGF1α, a stable metabolite of prostacyclin, levels were measured and mean blood pressures were recorded. In the preoperative group, 6-keto-PGF1α levels did not increase, blood pressure levels did not decrease, and no facial flushing was observed. In both the post-MTS and control groups, 6-keto-PGF1α levels increased markedly after mesenteric traction and blood pressure decreased significantly. The post-MTS group exhibited a faster decreasing trend in 6-keto-PGF1α levels and quick restore of the mean blood pressure, and the use of vasopressors and phenylephrine were lower than that in the control group. Even therapeutic administration of flurbiprofen axetil after the onset of MTS has also effects on MTS by suppressing prostacyclin production. Clinical trial number: UMIN000009111 . (Registered 14 October 2012).

  2. Tangential vitreous traction: a possible mechanism of development of cystoid macular edema in retinitis pigmentosa

    Directory of Open Access Journals (Sweden)

    Mikiko Takezawa

    2011-02-01

    Full Text Available Mikiko Takezawa, Soichi Tetsuka, Akihiro KakehashiDepartment of Ophthalmology, Jichi Medical University, Saitama Medical Center, Saitama, Saitama, JapanAbstract: We report the possible mechanism of development of cystoid macular edema (CME in retinitis pigmentosa (RP in the case of a 68-year-old woman with RP and CME in the right eye and resolving CME in the left eye. Spectral domain optical coherence tomography showed CME and posterior vitreoschisis in the nasal quadrant of the fundus without a posterior vitreous detachment (PVD. This vitreous pathology suggested bilateral thickening and shrinkage of the posterior vitreous cortex. In the right eye, CME was evident with no vitreofoveal separation. However, in the left eye, minimal change was seen in the CME associated with a focal shallow PVD over the fovea. The best-corrected visual acuity (BCVA in the left eye increased to 0.3 from 0.15 7 years after the first visit. Tangential vitreous traction on the macula may have caused the CME in the right eye. The shallow PVD over the fovea might have released the tangential vitreous traction from the fovea, induced spontaneous resolution of the CME, and improved the BCVA in the left eye.Keywords: retinitis pigmentosa, cystoid macular edema, posterior vitreous detachment, posterior vitreoschisis, optical coherence tomography

  3. Harmonic analysis of traction power supply system based on wavelet decomposition

    Science.gov (United States)

    Dun, Xiaohong

    2018-05-01

    With the rapid development of high-speed railway and heavy-haul transport, AC drive electric locomotive and EMU large-scale operation in the country on the ground, the electrified railway has become the main harmonic source of China's power grid. In response to this phenomenon, the need for timely monitoring of power quality problems of electrified railway, assessment and governance. Wavelet transform is developed on the basis of Fourier analysis, the basic idea comes from the harmonic analysis, with a rigorous theoretical model, which has inherited and developed the local thought of Garbor transformation, and has overcome the disadvantages such as window fixation and lack of discrete orthogonally, so as to become a more recently studied spectral analysis tool. The wavelet analysis takes the gradual and precise time domain step in the high frequency part so as to focus on any details of the signal being analyzed, thereby comprehensively analyzing the harmonics of the traction power supply system meanwhile use the pyramid algorithm to increase the speed of wavelet decomposition. The matlab simulation shows that the use of wavelet decomposition of the traction power supply system for harmonic spectrum analysis is effective.

  4. The XXI century mountains: sustainable management of mountainous areas based on animal traction

    Directory of Open Access Journals (Sweden)

    Rodrigues J.B.

    2017-02-01

    Full Text Available According to the Food and Agriculture Organization of the United Nations (FAO, there are around 300 million working animals worldwide. They play a fundamental role in human livelihoods through their contribution to financial, human and social capital, supporting between 300 and 600 million people globally, particularly in poorer areas, where animal energy represents a huge and extremely important sustainable power resource. Yet their recognition remains largely neglected, with animal traction being largely ignored by decision and policy makers and even by civil society at all levels, which compromises a real development and improvement of this technology as well as animal welfare. On the other hand, a collective ecological and economical consciousness and an increasing awareness of public opinion about the need to reduce the excessive industrialization and mechanization of agriculture and forestry has led some sectors of society to consider the (reuse of animal traction as a valid modern source of energy. Indeed, working animals optimally transform the consumed biomass in energy and natural fertilizer, which avoids soil degradation and contributes to a sustainable management of arable lands, forests and sensitive areas. The need to maintain biodiversity, reduce carbon emissions, encourage self-reliance and reduce consumption of resources also contributes to this trend.

  5. Investigation of control system of traction electric drive with feedbacks on load

    Science.gov (United States)

    Kuznetsov, N. K.; Iov, I. A.; Iov, A. A.

    2018-03-01

    In the article, by the example of a walking excavator, the results of a study of a control system of traction electric drive with a rigid and flexible feedback on the load are mentioned. Based on the analysis of known works, the calculation scheme has been chosen; the equations of motion of the electromechanical system have been obtained, taking into account the elasticity of the rope and feedbacks on the load in the elastic element. A simulation model of this system has been developed and mathematical modeling of the transient processes to evaluate the influence of feedback on the dynamic characteristics of the mechanism and its efficiency of work was carried out. It is shown that the use of rigid and flexible feedbacks makes it possible to reduce dynamic loads in the traction mechanism and to limit the elastic oscillation of the executive mechanism in transient operating modes in comparison with the standard control system; however, there is some decrease in productivity. It has been also established that the sign-variable of the loading of the electric drive, connected with the opening of the backlashes in the gearbox due to the action of feedbacks on the load in the elastic element, under certain conditions, can lead to undesirable phenomena in the operation of the drive and a decrease in the reliability of its operation.

  6. Influence of the braking power control of the traction asynchronous machine in the voltage vector control system under DC

    Directory of Open Access Journals (Sweden)

    Юлія Олександрівна Слободенюк

    2016-11-01

    Full Text Available At braking the traction motors are transferred to generator mode and produce electrical energy which passes to the contact mains or storage device in the DC mains for further use. Such braking is called regenerative. The resulting electrical energy can be spent by trains in traction mode. Regenerative braking reduces the consumption of electric power for traction. In electric railways of our country more than 3% of the consumed electrical energy is given back to contact mains annually. As this takes place there arises the task to control the braking of the traction motors with minimal impact on electric power quality and maintaining proper braking performance. Based on the analysis of the characteristics of the brake traction of an electric locomotive with asynchronous electric machines the main braking modes have been chosen: at a constant sliding speed and the stator constant voltage; at constant braking power and the stator constant voltage; at a power value more than the nominal braking power; at a constant load torque; at a constant frequency of the stator. The vector control system with the formation of the reactive component of the stator current and the EMF regulator was chosen, basing on the working conditions characteristics in the electric braking mode (recuperation; namely, that the characteristics are defined by the laws regulating the frequency and voltage across the stator windings. This control system can fully reproduce any predetermined trajectory of traction and braking performance and adjust braking power. The offered system with recuperation can be used as a means of compensation in emergency situations with a power failure

  7. Lingual traction to facilitate fiber-optic intubation of difficult airways: a single-anesthesiologist randomized trial.

    Science.gov (United States)

    Ching, Yiu-Hei; Karlnoski, Rachel A; Chen, Henian; Camporesi, Enrico M; Shah, Vimal V; Padhya, Tapan A; Mangar, Devanand

    2015-04-01

    Flexible fiber-optic bronchoscope-guided orotracheal intubation is a valuable technique with demonstrated benefits in the management of difficult airways. Despite its popularity with anesthesia providers, the technique is not fail-safe and airway-related complications secondary to failed intubation attempts remain an important problem. We sought to determine the effect of incorporating lingual traction on the success rate of fiber-optic bronchoscope-guided intubation in patients with anticipated difficult airways. In this prospective, randomized, cohort study, we enrolled 91 adult patients with anticipated difficult airways scheduled for elective surgery to undergo fiber-optic bronchoscope-guided orotracheal intubation alone or with lingual traction by an individual anesthesiologist after induction of general anesthesia and neuromuscular blockade. A total of 78 patients were randomized: 39 patients to the fiber-optic bronchoscope-guided intubation with lingual traction group and 39 patients to the fiber-optic bronchoscope-guided intubation alone group. The primary endpoint was the rate of successful first attempt intubations. The secondary outcome was sore throat grade on post-operative day 1. Fiber-optic intubation with lingual traction compared to fiber-optic intubation alone resulted in a higher success rate (92.3 vs. 74.4 %, χ (2) = 4.523, p = 0.033) and greater odds for successful first attempt intubation (OR 4.138, 95 % CI 1.041-16.444, p = 0.044). Sore throat severity on post-operative day 1 was not significantly different but trended towards worsening grades with lingual traction. In this study, lingual traction was shown to be a valuable maneuver for facilitating fiber-optic bronchoscope-guided intubation in the management of patients with anticipated difficult airways.

  8. Maintenance of working capacity of movement mechanism of load trolley with linear traction electric drive of bridge type crane.

    Science.gov (United States)

    Goncharov, K. A.; Denisov, I. A.

    2017-10-01

    The article considers the influence of the air gap size between the linear motor elements on the stability of the traction drive of the movement mechanism of the trolley of the bridge type crane. The main factors affecting the air gap size and the causes of their occurrence are described. The technique of calculating the magnitude of air gap variation is described in relation to the general deformation of the crane metal structure. Recommendations on the need for installation of additional equipment for load trolleys of various designs are given. The optimal values of the length of the trolley base are proposed. Observance of these values ensures normal operation of the traction drive.

  9. Feasibility study on the interconnection of traction and other power line infrastructures; Machbarkeitsstudie zur Verknuepfung von Bahn- und Energieleitungsinfrastrukturen

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, Lutz [Hannover Univ. (Germany). Inst. fuer Energieversorgung und Hochspannungstechnik; Stephan, Arnd [Technische Univ. Dresden (Germany). Professur Elektrische Bahnen; Weyer, Hartmut [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. fuer Deutsches und Internationales Berg- und Energierecht

    2013-06-15

    It was the purpose of the feasibility study to find out if and to what extent the existing transmission route potentials of the 16.7 Hz traction power network (DB Energie GmbH) can be used for the installation of new transmission lines of the standard 50 Hz power supply system. Of importance is here the question if and in which way the integration of new three-phase or DC overhead lines or cable systems in existing traction power routes is technically feasible, and to what extent such interconnection offers a potential for the acceleration of the planning and approval processes. (orig.)

  10. Numerical approach for optimum electromagnetic parameters of electrical machines used in vehicle traction applications

    International Nuclear Information System (INIS)

    Fodorean, D.; Giurgea, S.; Djerdir, A.; Miraoui, A.

    2009-01-01

    A large speed variation is an essential request in the automobile industry. In order to compete with diesel engines, the flux weakening technique has to be employed on the electrical machines. In this way, appropriate electromagnetic and geometrical parameters can give the desired speed. Using the inverse problem method coupled with numerical analysis by finite element method (FEM), the authors propose an optimum parameters configuration that maximizes the speed domain operation. Several types of electrical machines are under study: induction, synchronous permanent magnet, variable reluctance and transverse flux machines, respectively. With a proper non-linear model, by using analytical and numerical calculation, the authors propose an optimum solution for the speed variation of the studied drives, which will be standing for a final comparison.

  11. Application of artificial neural networks for the prediction of traction performance parameters

    Directory of Open Access Journals (Sweden)

    Hamid Taghavifar

    2014-01-01

    Full Text Available This study handles artificial neural networks (ANN modeling to predict tire contact area and rolling resistance due to the complex and nonlinear interactions between soil and wheel that mathematical, numerical and conventional models fail to investigate multivariate input and output relationships with nonlinear and complex characteristics. Experimental data acquisitioning was carried out using a soil bin facility with single-wheel tester at seven inflation pressures of tire (i.e. 100–700 kPa and seven different wheel loads (1–7 KN with two soil textures and two tire types. The experimental datasets were used to develop a feed-forward with back propagation ANN model. Four criteria (i.e. R-value, T value, mean squared error, and model simplicity were used to evaluate model’s performance. A well-trained optimum 4-6-2 ANN provided the best accuracy in modeling contact area and rolling resistance with regression coefficients of 0.998 and 0.999 and T value and MSE of 0.996 and 2.55 × 10−12, respectively. It was found that ANNs due to faster, more precise, and considerably reliable computation of multivariable, nonlinear, and complex computations are highly appropriate for soil–wheel interaction modeling.

  12. A review and design of power electronics converters for fuel cell hybrid system applications

    DEFF Research Database (Denmark)

    Zhang, Zhe; Pittini, Riccardo; Andersen, Michael A. E.

    2012-01-01

    This paper presents an overview of most promising power electronics topologies for a fuel cell hybrid power conversion system which can be utilized in many applications such as hybrid electrical vehicles (HEV), distributed generations (DG) and uninterruptible-power-supply (UPS) systems. Then...

  13. A Soft-Switching Inverter for High-Temperature Advanced Hybrid Electric Vehicle Traction Motor Drives

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Jason [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Yu, Wensong [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Sun, Pengwei [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Leslie, Scott [Powerex, Inc., Harrison, OH (United States); Prusia, Duane [Powerex, Inc., Harrison, OH (United States); Arnet, Beat [Azure Dynamics, Oak Park, MI (United States); Smith, Chris [Azure Dynamics, Oak Park, MI (United States); Cogan, Art [Azure Dynamics, Oak Park, MI (United States)

    2012-03-31

    The state-of-the-art hybrid electric vehicles (HEVs) require the inverter cooling system to have a separate loop to avoid power semiconductor junction over temperatures because the engine coolant temperature of 105°C does not allow for much temperature rise in silicon devices. The proposed work is to develop an advanced soft-switching inverter that will eliminate the device switching loss and cut down the power loss so that the inverter can operate at high-temperature conditions while operating at high switching frequencies with small current ripple in low inductance based permanent magnet motors. The proposed tasks also include high-temperature packaging and thermal modeling and simulation to ensure the packaged module can operate at the desired temperature. The developed module will be integrated with the motor and vehicle controller for dynamometer and in-vehicle testing to prove its superiority. This report will describe the detailed technical design of the soft-switching inverters and their test results. The experiments were conducted both in module level for the module conduction and switching characteristics and in inverter level for its efficiency under inductive and dynamometer load conditions. The performance will be compared with the DOE original specification.

  14. MR findings associated with positive distraction of the hip joint achieved by axial traction

    Energy Technology Data Exchange (ETDEWEB)

    Suter, Aline; Dietrich, Tobias J.; Maier, Matthias; Pfirrmann, Christian W.A. [Radiology, Orthopedic University Hospital Balgrist, Zurich (Switzerland); University of Zurich, Faculty of Medicine, Zurich (Switzerland); Dora, Claudio [Orthopedic University Hospital Balgrist, Orthopedic Surgery, Zurich (Switzerland); University of Zurich, Faculty of Medicine, Zurich (Switzerland)

    2015-06-01

    To determine which MR-arthrography findings are associated with positive hip joint distraction. One hundred patients with MR arthrography of the hip using axial traction were included. Traction was applied during the MR examination with an 8 kg (females) or 10 kg (males) water bag, attached to the ankle over a deflection pulley. Fifty patients showing joint space distraction were compared to an age- and gender-matched control group of 50 patients that did not show a joint distraction under axial traction. Two radiologists assessed the neck-shaft angle, lateral and anterior center-edge (CE) angles, CE angles in the transverse plane, extrusion index of the femoral head, acetabular depth, alpha angle, acetabular version, ligamentum teres, joint capsule and ligaments, iliopsoas tendon and the labrum. Mean joint space distraction in the study group was 0.9 ± 0.6 mm. Patients with positive joint space distraction had significantly higher neck-shaft angles (control group 131.6 ± 5.4 /study group 134.1 ± 6.1 , p < 0.05), smaller lateral CE angles (38.1 ± 5.9 /34.6 ± 7.2 , p < 0.05), smaller overall transverse CE angles (161.4 ± 9.9 /153.6 ± 9.6 , p < 0.001), smaller acetabular depth (4.1 ± 2.4 mm/5.8 ± 2.5 mm, p < 0.01), higher alpha angles (53.5 ± 7.8 /59.2 ± 10.1 , p < 0.01) and a thicker ligamentum teres (4.7 ± 1.4 mm/5.4 ± 1.8 mm, p < 0.05). The other parameters revealed no significant differences. ICC values for interobserver agreement were 0.71-0.95 and kappa values 0.43-0.92. Increased neck-shaft angles, small CE angles, small acetabular depth, higher alpha angles and a thick ligamentum teres are associated with positive joint distraction. (orig.)

  15. [SCREW-BASED INTERMAXILLARY TRACTION COMBINED WITH OCCLUSAL SPLINT FOR TREATMENT OF PEDIATRIC MANDIBULAR CONDYLAR FRACTURE].

    Science.gov (United States)

    Wu, Yang; Long, Xing; Deng, Mohong; Cai, Hengxing; Meng, Qinggong; Li, Bo

    2015-04-01

    To evaluate the effectiveness of the screw-based intermaxillary traction combined with occlusal splint in the treatment of pediatric mandibular condylar fracture. Between June 2005 and December 2013, 35 pediatric patients with 49 mandibular condylar fractures were treated, and the clinical data were retrospectively reviewed. There were 25 boys and 10 girls, aged 3-13 years (mean, 7.3 years). The injury causes included falling (18 cases), traffic accident (14 cases), and violence (3 cases). The time between injury and treatment was 2-30 days (mean, 6.8 days). Restricted mouth opening was observed, and the maximal mouth opening was (22.74 +/- 7.22) mm except 3 patients who were too young to measure. Condylar fractures were located at the left (12 cases), at the right (9 cases), at bilateral (14 cases) based on the sites; and fractures were classified as intracapsular (35 fractures), neck (10 fractures), and subcondylar (4 fractures) based on the fracture line. Four self-drilling titanium screws were inserted into the alveolar bone of both maxilla and mandible. After screw inserting, an occlusal splint with a fulcrum was used on the affected side and elastic band was put to perform anterior intermaxillary traction. After 1 month, the screws and splint were removed. Follow-up examinations were carried out on schedule. All the patients were followed up from 6 months to 8 years and 10 months (median, 71 months). No screw-related complication occurred in the others except one case of screw loosening. The postoperative maximal mouth opening was (38.82 +/- 2.02) nim. Mild joint noise was found in 4 cases and opening deviation occurred in 6 cases. Radiographic results demonstrated complete condyle remodeling was achieved in 24 cases (32 fractures), and moderate remodeling in 11 cases (17 fractures) at last follow-up. The screw-based intermaxillary traction combined with occlusal splint might be an effective method for pediatric mandibular condylar fracture. The screw

  16. MR findings associated with positive distraction of the hip joint achieved by axial traction

    International Nuclear Information System (INIS)

    Suter, Aline; Dietrich, Tobias J.; Maier, Matthias; Pfirrmann, Christian W.A.; Dora, Claudio

    2015-01-01

    To determine which MR-arthrography findings are associated with positive hip joint distraction. One hundred patients with MR arthrography of the hip using axial traction were included. Traction was applied during the MR examination with an 8 kg (females) or 10 kg (males) water bag, attached to the ankle over a deflection pulley. Fifty patients showing joint space distraction were compared to an age- and gender-matched control group of 50 patients that did not show a joint distraction under axial traction. Two radiologists assessed the neck-shaft angle, lateral and anterior center-edge (CE) angles, CE angles in the transverse plane, extrusion index of the femoral head, acetabular depth, alpha angle, acetabular version, ligamentum teres, joint capsule and ligaments, iliopsoas tendon and the labrum. Mean joint space distraction in the study group was 0.9 ± 0.6 mm. Patients with positive joint space distraction had significantly higher neck-shaft angles (control group 131.6 ± 5.4 /study group 134.1 ± 6.1 , p < 0.05), smaller lateral CE angles (38.1 ± 5.9 /34.6 ± 7.2 , p < 0.05), smaller overall transverse CE angles (161.4 ± 9.9 /153.6 ± 9.6 , p < 0.001), smaller acetabular depth (4.1 ± 2.4 mm/5.8 ± 2.5 mm, p < 0.01), higher alpha angles (53.5 ± 7.8 /59.2 ± 10.1 , p < 0.01) and a thicker ligamentum teres (4.7 ± 1.4 mm/5.4 ± 1.8 mm, p < 0.05). The other parameters revealed no significant differences. ICC values for interobserver agreement were 0.71-0.95 and kappa values 0.43-0.92. Increased neck-shaft angles, small CE angles, small acetabular depth, higher alpha angles and a thick ligamentum teres are associated with positive joint distraction. (orig.)

  17. A mesenteric traction syndrome affects near-infrared spectroscopy evaluated cerebral oxygenation because skin blood flow increases

    DEFF Research Database (Denmark)

    Olesen, Niels D; Sørensen, Henrik; Ambrus, Rikard

    2018-01-01

    During abdominal surgery manipulation of internal organs may induce a "mesenteric traction syndrome" (MTS) including a triad of flushing, hypotension, and tachycardia that lasts for about 30 min. We evaluated whether MTS affects near-infrared spectroscopy (NIRS) assessed frontal lobe oxygenation ...

  18. Analysis of the process related to the operations management of the rail traction vehicles in JSC 'Serbian Railways'

    Directory of Open Access Journals (Sweden)

    Vukadinović Vojislav

    2016-01-01

    Full Text Available In the study, issues related to the operations management in railway were elaborated, with special emphasis on the operations management of rail vehicles and main parameters in its activities and in the railway functioning. The analysis of the current status, operation and functioning of the Serbian Railways was also provided, with a special focus on the study of the technical condition regarding exploitation, reliability, and availability of traction vehicles operation which is always actual and particularly important for ensuring the regular and safe functioning of train traffic in all railways in the world as well as in the railway of Serbia. The issue related to the exploitation reliability and availability regarding traction vehicles operation is also being analyzed which is reflected in development of the concept and creation of the methodology for assessment of the technical condition and indicators for determining the level of exploitation reliability, availability of the traction vehicle operation as well as functioning of train traffic and the models related to the operations management of rail traction vehicles.

  19. Evaluation of Strategies to Reducing Traction Energy Consumption of Metro Systems Using an Optimal Train Control Simulation Model

    Directory of Open Access Journals (Sweden)

    Shuai Su

    2016-02-01

    Full Text Available Increasing attention is being paid to the energy efficiency in metro systems to reduce the operational cost and to advocate the sustainability of railway systems. Classical research has studied the energy-efficient operational strategy and the energy-efficient system design separately to reduce the traction energy consumption. This paper aims to combine the operational strategies and the system design by analyzing how the infrastructure and vehicle parameters of metro systems influence the operational traction energy consumption. Firstly, a solution approach to the optimal train control model is introduced, which is used to design the Optimal Train Control Simulator(OTCS. Then, based on the OTCS, the performance of some important energy-efficient system design strategies is investigated to reduce the trains’ traction energy consumption, including reduction of the train mass, improvement of the kinematic resistance, the design of the energy-saving gradient, increasing the maximum traction and braking forces, introducing regenerative braking and timetable optimization. As for these energy-efficient strategies, the performances are finally evaluated using the OTCS with the practical operational data of the Beijing Yizhuang metro line. The proposed approach gives an example to quantitatively analyze the energy reduction of different strategies in the system design procedure, which may help the decision makers to have an overview of the energy-efficient performances and then to make decisions by balancing the costs and the benefits.

  20. Windowed SHE-PWM of Interleaved Four-Quadrant Converters for Resonance Suppression in Traction Power Supply Systems

    DEFF Research Database (Denmark)

    Song, Kejian; Konstantinou, Georgios; Mingli, Wu

    2017-01-01

    AC electric locomotives that use a number of interleaved four-quadrant converters generate high-frequency switching harmonics which may stimulate certain resonances in traction power supply systems (TPSSs). A windowed selective harmonic elimination pulse-width modulation (SHE-PWM) method...

  1. Cellular adhesome screen identifies critical modulators of focal adhesion dynamics, cellular traction forces and cell migration behaviour

    Science.gov (United States)

    Fokkelman, Michiel; Balcıoğlu, Hayri E.; Klip, Janna E.; Yan, Kuan; Verbeek, Fons J.; Danen, Erik H. J.; van de Water, Bob

    2016-01-01

    Cancer cells migrate from the primary tumour into surrounding tissue in order to form metastasis. Cell migration is a highly complex process, which requires continuous remodelling and re-organization of the cytoskeleton and cell-matrix adhesions. Here, we aimed to identify genes controlling aspects of tumour cell migration, including the dynamic organization of cell-matrix adhesions and cellular traction forces. In a siRNA screen targeting most cell adhesion-related genes we identified 200+ genes that regulate size and/or dynamics of cell-matrix adhesions in MCF7 breast cancer cells. In a subsequent secondary screen, the 64 most effective genes were evaluated for growth factor-induced cell migration and validated by tertiary RNAi pool deconvolution experiments. Four validated hits showed significantly enlarged adhesions accompanied by reduced cell migration upon siRNA-mediated knockdown. Furthermore, loss of PPP1R12B, HIPK3 or RAC2 caused cells to exert higher traction forces, as determined by traction force microscopy with elastomeric micropillar post arrays, and led to considerably reduced force turnover. Altogether, we identified genes that co-regulate cell-matrix adhesion dynamics and traction force turnover, thereby modulating overall motility behaviour. PMID:27531518

  2. Pneumatic-type dynamic traction and flexion splint for treating patients with extension contracture of the metacarpophalangeal joint.

    Science.gov (United States)

    Nakayama, Jun; Horiki, Mituru; Denno, Kakurou; Ogawa, Kazunori; Oka, Hisao; Domen, Kazuhisa

    2016-02-01

    Collateral ligament shortening causes extension contractures of the metacarpophalangeal joint, and dynamic flexion splinting has been widely used to treat these contractures; however, there are various problems with these approaches. We developed a novel, pneumatic-type dynamic traction and flexion splint to solve these problems. A total of 25 fingers were treated with the dynamic traction and flexion splint for 8 weeks. Every 2 weeks, the average metacarpophalangeal joint flexion angle, total active motion, grasp strength, and pain scores were assessed. The finger flexion angle was significantly greater at the final evaluation, starting after 6 weeks of treatment (p < 0.05), than prior to treatment. Similarly, the total active motion results improved significantly over 8 weeks. Our results show that use of the dynamic traction and flexion splint improves patient finger functioning and flexural angle. The dynamic traction and flexion (DTF) splint appears to be effective for treating patients. © The International Society for Prosthetics and Orthotics 2015.

  3. Non-canonical spectral decomposition of random functions of the traction voltage and current in electric transportation systems

    Directory of Open Access Journals (Sweden)

    N.A. Kostin

    2015-03-01

    Full Text Available The paper proposes the non-canonical spectral decomposition of random functions of the traction voltages and currents. This decomposition is adapted for the electric transportation systems. The numerical representation is carried out for the random function of voltage on the pantograph of electric locomotives VL8 and DE1.

  4. Mode of the short circuit in the direct current electric traction network with different feed charts of fyder area

    Directory of Open Access Journals (Sweden)

    P. Mihalichenko

    2012-12-01

    Full Text Available In the article the results of mathematical design of the system of electric traction of direct current are represented in the mode of short circuit and different feed charts of fyder area: two-sided; one-sided. Comparison of transitional electric sizes which characterize electromagnetic processes during these malfunctions is analysed and executed.

  5. High performance control strategy for single-phase three-level neutral-point-clamped traction four-quadrant converters

    DEFF Research Database (Denmark)

    Kejian, Song; Konstantinou, Georgios; Jing, Li

    2017-01-01

    Operational data from Chinese railways indicate a number of challenges for traction four-quadrant converter (4QC) control including low-order voltage and current harmonics and reference tracking. A control strategy for a single-phase three-level neutral-point-clamped 4QC employed in the electric...

  6. Model for adhesion clutch explains biphasic relationship between actin flow and traction at the cell leading edge

    Science.gov (United States)

    Craig, Erin M.; Stricker, Jonathan; Gardel, Margaret L.; Mogilner, Alex

    2015-01-01

    Cell motility relies on the continuous reorganization of a dynamic actin-myosin-adhesion network at the leading edge of the cell, in order to generate protrusion at the leading edge and traction between the cell and its external environment. We analyze experimentally measured spatial distributions of actin flow, traction force, myosin density, and adhesion density in control and pharmacologically perturbed epithelial cells in order to develop a mechanical model of the actin-adhesion-myosin self-organization at the leading edge. A model in which the F-actin network is treated as a viscous gel, and adhesion clutch engagement is strengthened by myosin but weakened by actin flow, can explain the measured molecular distributions and correctly predict the spatial distributions of the actin flow and traction stress. We test the model by comparing its predictions with measurements of the actin flow and traction stress in cells with fast and slow actin polymerization rates. The model predicts how the location of the lamellipodium-lamellum boundary depends on the actin viscosity and adhesion strength. The model further predicts that the location of the lamellipodium-lamellum boundary is not very sensitive to the level of myosin contraction. PMID:25969948

  7. Disturbance Observer-Based Backstepping Control of PMSM for the Mine Traction Electric Locomotive

    Directory of Open Access Journals (Sweden)

    Jiande Yan

    2018-01-01

    Full Text Available For the Permanent Magnet Synchronous Motor (PMSM control system of the Mine Traction Electric Locomotive (MTEL, the fluctuation of the load will lead to the resonance of the velocity of the MTEL. In addition, the speed sensor is easy to be damaged due to the moisture, dust, and vibration. To solve the above problems, a disturbance observer-based (DOB backstepping control of PMSM for the MTEL is proposed in this paper. First, a full-dimensional Luenberger observer for PMSM is designed and the asymptotically stability of the observer is proved. Next, through the designing of the virtual control input that includes the reconstruction disturbances and using backstepping control strategy, the DOB controller is proposed. The obtained controller can achieve high precision speed tracking and disturbance rejection. Finally, the effectiveness and feasibility of the designed system are verified by Matlab simulation and experiment results.

  8. Visualizing the interior architecture of focal adhesions with high-resolution traction maps.

    Science.gov (United States)

    Morimatsu, Masatoshi; Mekhdjian, Armen H; Chang, Alice C; Tan, Steven J; Dunn, Alexander R

    2015-04-08

    Focal adhesions (FAs) are micron-sized protein assemblies that coordinate cell adhesion, migration, and mechanotransduction. How the many proteins within FAs are organized into force sensing and transmitting structures is poorly understood. We combined fluorescent molecular tension sensors with super-resolution light microscopy to visualize traction forces within FAs with <100 nm spatial resolution. We find that αvβ3 integrin selectively localizes to high force regions. Paxillin, which is not generally considered to play a direct role in force transmission, shows a higher degree of spatial correlation with force than vinculin, talin, or α-actinin, proteins with hypothesized roles as force transducers. These observations suggest that αvβ3 integrin and paxillin may play important roles in mechanotransduction.

  9. A traction control strategy with an efficiency model in a distributed driving electric vehicle.

    Science.gov (United States)

    Lin, Cheng; Cheng, Xingqun

    2014-01-01

    Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the two-dimensional design space composed of the acceleration pedal signal and the vehicle speed. The sliding mode control strategy for the joint roads and the efficiency model for the typical drive cycles were simulated. Simulation results show that the proposed driving control approach has the potential to apply to different road surfaces. It keeps the wheels' slip ratios within the stable zone and improves the fuel economy on the premise of tracking the driver's intention.

  10. Suppression of experimental tractional retinal detachment by low-dose radiation therapy

    International Nuclear Information System (INIS)

    Meredith, T.A.; Ficker, L.; Stevens, R.; Olkowski, Z.; Anderson, M.; Hartmann, J.; Crocker, I.

    1988-01-01

    We used a standardized model of traction retinal detachment (TRD) created by cellular membranes in the rabbit to test the effects of low-dose radiation therapy in suppressing TRD. The vitreous and lens were removed from pigmented rabbits, and homologous conjunctival fibroblasts were grown in cell culture. After resolution of postoperative inflammation, 50,000 fibroblasts in 0.1 mL of culture fluid were injected into the vitreous cavity. Ten eyes were maintained as controls. Nineteen eyes received 6 Gy (600 rad) of x-ray irradiation one to three hours after cellular injection. Eyes were monitored weekly for three weeks with indirect ophthalmoscopy. Seven (70%) of ten control eyes developed TRD at one week; no additional TRDs were noted at weeks 2 and 3. Significantly smaller numbers of irradiated eyes developed TRD: at week 1, two (11%) of 19; at week 2, five (28%) of 18; and at week 3, five (29%) of 17

  11. The wall traction induced by flowing red blood cells in model microvessels and its potential mechanotransduction

    Science.gov (United States)

    Freund, Jonathan; Vermot, Julien

    2013-11-01

    There is evidence in early embryonic development, even well before advective oxygen transport is important, that the presence of red bloods cells per se trigger essential steps of normal vascular development. For example, showed that sequestration of blood cells early in the development of a mouse, such that the hematocrit is reduced, suppresses normal vascular network development. Vascular development also provides a model for remodeling and angiogenesis. We consider the transient stresses associated with blood cells flowing in model microvessels of comparable diameter to those at early stages of development (6 μm to 12 μm). A detailed simulation tool is used to show that passing blood cells present a significant fluctuating traction signature on the vessel wall, well above the mean stresses. This is particularly pronounced for slow flows (layer is also considered. NSF supported.

  12. A Traction Control Strategy with an Efficiency Model in a Distributed Driving Electric Vehicle

    Science.gov (United States)

    Lin, Cheng

    2014-01-01

    Both active safety and fuel economy are important issues for vehicles. This paper focuses on a traction control strategy with an efficiency model in a distributed driving electric vehicle. In emergency situation, a sliding mode control algorithm was employed to achieve antislip control through keeping the wheels' slip ratios below 20%. For general longitudinal driving cases, an efficiency model aiming at improving the fuel economy was built through an offline optimization stream within the two-dimensional design space composed of the acceleration pedal signal and the vehicle speed. The sliding mode control strategy for the joint roads and the efficiency model for the typical drive cycles were simulated. Simulation results show that the proposed driving control approach has the potential to apply to different road surfaces. It keeps the wheels' slip ratios within the stable zone and improves the fuel economy on the premise of tracking the driver's intention. PMID:25197697

  13. First-order system least squares for the pure traction problem in planar linear elasticity

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Z.; Manteuffel, T.; McCormick, S.; Parter, S.

    1996-12-31

    This talk will develop two first-order system least squares (FOSLS) approaches for the solution of the pure traction problem in planar linear elasticity. Both are two-stage algorithms that first solve for the gradients of displacement, then for the displacement itself. One approach, which uses L{sup 2} norms to define the FOSLS functional, is shown under certain H{sup 2} regularity assumptions to admit optimal H{sup 1}-like performance for standard finite element discretization and standard multigrid solution methods that is uniform in the Poisson ratio for all variables. The second approach, which is based on H{sup -1} norms, is shown under general assumptions to admit optimal uniform performance for displacement flux in an L{sup 2} norm and for displacement in an H{sup 1} norm. These methods do not degrade as other methods generally do when the material properties approach the incompressible limit.

  14. Transvenous Lead Extraction via the Inferior Approach Using a Gooseneck Snare versus Simple Manual Traction.

    Science.gov (United States)

    Jo, Uk; Kim, Jun; Hwang, You-Mi; Lee, Ji-Hyun; Kim, Min-Su; Choi, Hyung-Oh; Lee, Woo-Seok; Kwon, Chang-Hee; Ko, Gi-Young; Yoon, Hyun-Ki; Nam, Gi-Byoung; Choi, Kee-Joon; Kim, You-Ho

    2016-03-01

    The number of patients with cardiac implantable electronic devices needing lead extraction is increasing for various reasons, including infections, vascular obstruction, and lead failure. We report our experience with transvenous extraction of pacemaker and defibrillator leads via the inferior approach of using a gooseneck snare as a first-line therapy and compare extraction using a gooseneck snare with extraction using simple manual traction. The study included 23 consecutive patients (43 leads) who underwent transvenous lead extraction using a gooseneck snare (group A) and 10 consecutive patients (17 leads) who underwent lead extraction using simple manual traction (group B). Patient characteristics, indications, and outcomes were analyzed and compared between the groups. The dwelling time of the leads was longer in group A (median, 121) than in group B (median, 56; p=0.000). No differences were noted in the overall procedural success rate (69.6% vs. 70%), clinical procedural success rate (82.6% vs. 90%), and lead clinical success rate (86% vs. 94.1%) between the groups. The procedural success rates according to lead type were 89.2% and 100% for pacing leads and 66.7% and 83.3% for defibrillator leads in groups A and B, respectively. Major complications were noted in 3 (mortality in 1) patients in group A and 2 patients in group B. Transvenous extraction of pacemaker leads via an inferior approach using a gooseneck snare was both safe and effective. However, stand-alone transvenous extraction of defibrillator leads using the inferior approach was suboptimal.

  15. Modified Longo's stapled hemorrhoidopexy with additional traction sutures for the treatment of residual prolapsed piles.

    Science.gov (United States)

    Chen, Chuang-Wei; Kang, Jung-Cheng; Wu, Chang-Chieh; Hsiao, Cheng-Wen; Jao, Shu-Wen

    2008-03-01

    Residual prolapsed piles is a problem after the stapled hemorrhoidopexy, especially in large third- or fourth-degree hemorrhoids. We have developed a method using additional traction sutures along with modified Longo's procedure to manage this problem. From January 2005 to October 2005, 30 consecutive patients with symptomatic third- or fourth-degree hemorrhoids who underwent the modified Longo's stapled hemorrhoidopexy with additional traction sutures in a single institution were collected. The demographics, postoperative pain score, surgical features, outcomes, and early and late complications were recorded. All patients were followed for a mean duration of 8.8 (range, 4-15) months. Thirty patients (17 males) with a mean age of 45 (range, 27-63) years were identified. The mean postoperative pain score on the morning of the first postoperative day was 2.8 (range, 1-4). The mean duration of operation was 30.7 (range, 25-37) min. The mean duration of hospital stay was 2 (range, 1-3) days. The mean days for patients to resume normal work was 6.7 (range, 4-9) days. No other procedure-related complications occurred in all patients. There was no early complication except for fecal urgency found in one patient during the first postoperative days. Regarding the late complications, no residual prolapsed piles, persistent anal pain, incontinence, anal stenosis, or recurrent symptoms were found. Our preliminary experiences indicated that this modified procedures truly contributed to reduce the residual internal hemorrhoids and maintained the benefits of stapled hemorrhoidopexy. Randomized trial and long-term follow-up warrant to determine possible surgical and functional outcome.

  16. Frequency of vitreo macular traction in diabetic macular edema on optical coherence tomography

    International Nuclear Information System (INIS)

    Fatima, N.; Islam, Q.U.; Shafique, M.

    2017-01-01

    To determine the frequency of vitreo macular traction (VMT) in patients of diabetic macular edema (DME) as detected on spectral domain optical coherence tomography (SD-OCT). Study Design: Cross-sectional study. Place and Duration of Study: Armed Forces Institute of Ophthalmology (AFIO) Rawalpindi, from May 2013 to Jan 2014. Patients and Methods: Diabetic patients of less than 18 years of age with DME and central macular thickness of more than 250 micrometers (micro m) were included. The patients with idiopathic VMT, history of vitreoretinal surgery, and history of other retinal vascular diseases were excluded from the study. Dilated fundus was done in each patient using 90 D lens on a slit lamp biomicroscope and patients with diabetic retinopathy changes and DME were subjected to OCT examination using Topcon 3-D OCT 1000 (Topcon Corporation). Record of each patient including demographic data, ocular findings and OCT data were endorsed on a pre-devised proforma. Results: Seventy one eyes of 68 patients were included, 36 (50.7 percent) were males and 35 (49.29 percent) were females. Mean age was 53.17 +- 8.79 years. Mean central macular thickness (CMT) was 361.8 +- 109 mu m. VMT was detected in 17 (23.9 percent) eyes. Amongst these, 2(12.5 percent) eyes had vitreofoveal traction, epiretinal membrane was found in 4 (25 percent) eyes and 11(62.5 percent) eyes had extra foveal VMT. Conclusion: Detection of VMT in about a quarter of cases reflects that OCT is a viable tool for early detection of vitreomacular interface abnormalities. (author)

  17. Traction esophageal diverticulum: a rare cause of gastro-intestinal bleeding.

    Science.gov (United States)

    Ballehaninna, Umashankar K; Shaw, Jason P; Brichkov, Igor

    2012-12-01

    Esophageal diverticula are uncommon lesions that are usually classified according to their location (cervical, thoracic, or epiphrenic), or underlying pathogenesis (pulsion or traction), and their morphology (true or false).The majority of esophageal diverticula are acquired lesions that occur predominantly in elderly adults. Pulsion, or false, diverticula are the most commonly encountered type of esophageal diverticula noticed at the level of cricopharyngeus muscle, occur as a localized outpouchings that lacks a muscular coat, and as such their wall is formed entirely by mucosa and submucosa. True, or traction, esophageal diverticulum (TED) is seen in the middle one third of the thoracic esophagus in a peribronchial location, occurs secondary to mediastinal inflammatory lesions such as tuberculosis or histoplasmosis. The resultant desmoplastic reaction in the paraesophageal tissue causes full thickness pinching on the esophageal wall, producing a conical, broad-mouthed true diverticulum. They often project to the right side because subcarinal lymph nodes in this area are closely associated with the right anterior wall of the esophagus. TED usually presents with symptoms such as dysphagia, postural regurgitation, belching, retrosternal pain, heartburn, and epigastric pain. As in patients with pharyngoesophageal (Zenker's) diverticula, pulmonary symptoms are often present but underestimated in TED patients. These symptoms range from mild nocturnal cough to life-threatening massive aspiration. In this particular report we describe a rare case of TED presenting as a symptomatic upper gastrointestinal bleeding. Diagnostic evaluation of TED includes chest X-ray, barium esophagogram and manometry. A significant proportion of lower esophageal diverticula are associated with motility disorders. Management of TED include treating the underlying cause sometimes a surgical resection of diverticulum along with esophageal myotomy is necessitated in symptomatic patients.

  18. Regulation of unbalanced electromagnetic moment in mutual loading systems of electric machines of traction rolling stock and multiple unit of mainline and industrial transport

    Directory of Open Access Journals (Sweden)

    A. M. Afanasov

    2014-12-01

    Full Text Available Purpose. The research data are aimed to identify the regulatory principles of unbalanced electromagnetic moment of mutually loaded electric machines of traction rolling stock and multiple unit of main and industrial transport. The purpose of this study is energy efficiency increase of the testing of traction electric machines of direct and pulse current using the improvement methods of their mutual loading, including the principles of automatic regulation of mutual loading system. Methodology. The general theoretical provisions and principles of system approach to the theoretical electric engineering, the theory of electric machines and theoretical mechanics are the methodological basis of this research. The known methods of analysis of electromagnetic and electromechanical processes in electrical machines of direct and pulse current are used in the study. Methods analysis of loading modes regulation of traction electric machines was conducted using the generalized scheme of mutual loading. It is universal for all known methods to cover the losses of idling using the electric power. Findings. The general management principles of mutual loading modes of the traction electric machines of direct and pulse current by regulating their unbalanced electric magnetic moment were developed. Regulatory options of unbalanced electromagnetic moment are examined by changing the difference of the magnetic fluxes of mutually loaded electric machines, the current difference of electric machines anchors, the difference of the angular velocities of electric machines shafts. Originality. It was obtained the scientific basis development to improve the energy efficiency test methods of traction electric machines of direct and pulse current. The management principles of mutual loading modes of traction electric machines were formulated. For the first time it is introduced the concept and developed the principles of regulation of unbalanced electromagnetic moment in

  19. Effect of pregnancy on anti-HEV antibody titres, plasma cytokines and the corresponding gene expression levels in the PBMCs of patients presenting with self-recovering clinical and subclinical hepatitis E.

    Directory of Open Access Journals (Sweden)

    Ashwini Y Ramdasi

    Full Text Available High mortality in pregnant women (PR is a characteristic of hepatitis E in developing countries. To understand the pathogenesis of HEV infection in self-limiting disease during pregnancy, we compared clinical (PR-patients and subclinical-HEV-infections in pregnant women in the first (SC-PR-1 and later (2nd and 3rd, SC-PR-2+3 trimesters with the respective healthy controls and acute non-PR patients. The SC-PR-2+3 exhibited lower ALT, bilirubin levels, anti-HEV-IgM/IgG titres than the acute-PR/non-PR-patients (p<0.05-0.0001. IFNγ/IL4ratios indicated Th2/Th1 bias in non-PR and PR-patients respectively. Raised levels of 10/20 plasma cytokines in the non-PR-patients reflect predominant inflammatory response, unaltered- IFNγ/reduced-IFNα responses and a robust chemokine secretion. On contrary, the acute-PR-patients exhibited drastic reduction in majority of the cytokines relative to in the non-PR-patients. Importantly, diminished or unaltered response was noted in the acute-PR-group when compared to the corresponding controls. The only exception was sIL2RA, increasing in both patient categories. Of the 14 genes evaluated, the expression of IFNγ/IL10/IL1A/IL7/CCL2/CCL3/CXCL8/CXCL10 was higher in the non-PR patients. Of these, the expression of IFNγ/IL10/IL1A/CCL2/CCL3/CXCL8 and, additionally, IL2/IL6/TNF genes was higher in the clinical-PRs. Almost identical pattern was noted in the control-PR-2+3 category indicating no influence of HEV infection. Comparison of patient-categories identified significant elevation of IFNγ(P<0.001, CCL2(p<0.01, CXCL8(P<0.05, IL1B(p<0.05 and IL10(P<0.0001 and decrease in CXCL10(<0.05 in the PR-patients. The results suggest antibody-dependent disease severity and impaired immune response in the PR patients. Higher expression of cytokine-genes in the PBMCs did not correlate with the plasma-cytokine levels in the PR-patients.

  20. THE EIGHT-WHEEL LOCOMOTIVE DC3 WITH THE SECOND TYPE OF RATING UNLOADING AND ADDITIONAL LOADING OF WHEELS AND DEFLECTIONS SPRING SUSPENSION DURING TRACTION EFFORTS TRANSFER FROM BOGIES TO BODY WITH USING RECLINING TRACTIONS

    Directory of Open Access Journals (Sweden)

    V. A. Bratash

    2010-11-01

    Full Text Available In the article the calculation formulas for determination of unloadings (finishings loadings of wheels and bendings of a spring suspension of 8-wheel electric locomotive DS 3 with the hauling transmission of the second kind at the transmission of tractive forces from the bogies to the body through sloping tractions are presented. Numerical calculations are executed on the example of mainline freight-and-passenger electric locomotive DS 3.

  1. Improved throughput traction microscopy reveals pivotal role for matrix stiffness in fibroblast contractility and TGF-β responsiveness

    Science.gov (United States)

    Marinković, Aleksandar; Mih, Justin D.; Park, Jin-Ah; Liu, Fei

    2012-01-01

    Lung fibroblast functions such as matrix remodeling and activation of latent transforming growth factor-β1 (TGF-β1) are associated with expression of the myofibroblast phenotype and are directly linked to fibroblast capacity to generate force and deform the extracellular matrix. However, the study of fibroblast force-generating capacities through methods such as traction force microscopy is hindered by low throughput and time-consuming procedures. In this study, we improved at the detail level methods for higher-throughput traction measurements on polyacrylamide hydrogels using gel-surface-bound fluorescent beads to permit autofocusing and automated displacement mapping, and transduction of fibroblasts with a fluorescent label to streamline cell boundary identification. Together these advances substantially improve the throughput of traction microscopy and allow us to efficiently compute the forces exerted by lung fibroblasts on substrates spanning the stiffness range present in normal and fibrotic lung tissue. Our results reveal that lung fibroblasts dramatically alter the forces they transmit to the extracellular matrix as its stiffness changes, with very low forces generated on matrices as compliant as normal lung tissue. Moreover, exogenous TGF-β1 selectively accentuates tractions on stiff matrices, mimicking fibrotic lung, but not on physiological stiffness matrices, despite equivalent changes in Smad2/3 activation. Taken together, these results demonstrate a pivotal role for matrix mechanical properties in regulating baseline and TGF-β1-stimulated contraction of lung fibroblasts and suggest that stiff fibrotic lung tissue may promote myofibroblast activation through contractility-driven events, whereas normal lung tissue compliance may protect against such feedback amplification of fibroblast activation. PMID:22659883

  2. Integrated traction control strategy for distributed drive electric vehicles with improvement of economy and longitudinal driving stability

    OpenAIRE

    Zhang, Xudong; Göhlich, Dietmar

    2017-01-01

    This paper presents an integrated traction control strategy (ITCS) for distributed drive electric vehicles. The purpose of the proposed strategy is to improve vehicle economy and longitudinal driving stability. On high adhesion roads, economy optimization algorithm is applied to maximize motors efficiency by means of the optimized torque distribution. On low adhesion roads, a sliding mode control (SMC) algorithm is implemented to guarantee the wheel slip ratio around the optimal slip ratio po...

  3. Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

    OpenAIRE

    Krivtsov, Sergey; Syrbakov, Andrey Pavlovich; Korchuganova, Mariya Anatolievna

    2016-01-01

    This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

  4. Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

    Science.gov (United States)

    Krivtsov, Sergey N.; Syrbakov, Andrey P.; Korchuganova, Marina A.

    2016-08-01

    This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

  5. Traction batteries for industrial trucks. Technical aspects, selection criteria, operation. Antriebsbatterien fuer Flurfoerderzeuge. Technik, Auswahlkriterien und Betrieb

    Energy Technology Data Exchange (ETDEWEB)

    Roedig, W

    1987-01-01

    This lavishly illustrated booklet presents an introduction to the technology of the lead battery, which is commonly used as traction battery for industrial trucks. Technical specifications and standards, selection criteria for batteries and the novel CSM battery technology are mentioned. Most of the book deals with the practical aspects of batteries, e.g. installation, starting, maintenance, servicing, battery change, battery charging, monitoring, measurement, etc.). Battery recycling is briefly gone into.

  6. Properties and toxicological effects of particles from the interaction between tyres, road pavement and winter traction material

    Energy Technology Data Exchange (ETDEWEB)

    Gustafsson, Mats [Swedish National Road and Transport Research Institute (VTI), SE-581 95 Linkoeping (Sweden)], E-mail: mats.gustafsson@vti.se; Blomqvist, Goeran [Swedish National Road and Transport Research Institute (VTI), SE-581 95 Linkoeping (Sweden); Gudmundsson, Anders; Dahl, Andreas [Division of Ergonomics and Aerosol Technology, Department of Design Sciences, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Swietlicki, Erik [Division of Nuclear Physics, Department of Physics, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Bohgard, Mats [Division of Ergonomics and Aerosol Technology, Department of Design Sciences, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Lindbom, John; Ljungman, Anders [Faculty of Health Sciences, Department of Molecular and Clinical Medicine, Division of Occupational and Environmental Medicine, SE-581 85 Linkoeping (Sweden)

    2008-04-15

    In regions where studded tyres and traction material are used during winter, e.g. the Nordic countries, northern part of USA, Canada, and Japan, mechanically generated particles from traffic are the main reason for high particle mass concentrations in busy street and road environments. In many Nordic municipalities the European environmental quality standard for inhalable particles (PM{sub 10}) is exceeded due to these particles. In this study, particles from the wear of studded and studless friction tyres on two pavements and traction sanding were generated using a road simulator. The particles were characterized using particle sizers, Particle Induced X-Ray Emission Analysis and electron microscopy. Cell studies were conducted on particles sampled from the tests with studded tyres and compared with street environment, diesel exhaust and subway PM{sub 10}, respectively. The results show that in the road simulator, where resuspension is minimized, studded tyres produce tens of times more particles than friction tyres. Chemical analysis of the sampled particles shows that the generated wear particles consist almost entirely of minerals from the pavement stone material, but also that Sulfur is enriched for the submicron particles and that Zink is enriched for friction tyres for all particles sizes. The chemical data can be used for source identification and apportionment in urban aerosol studies. A mode of ultra-fine particles was also present and is hypothesised to originate in the tyres. Further, traction material properties affect PM{sub 10} emission. The inflammatory potential of the particles from wear of pavements seems to depend on type of pavement and can be at least as potent as diesel exhaust particles. The results imply that there is a need and a good potential to reduce particle emission from pavement wear and winter time road and street operation by adjusting both studded tyre use as well as pavement and traction material properties.

  7. Properties and toxicological effects of particles from the interaction between tyres, road pavement and winter traction material

    International Nuclear Information System (INIS)

    Gustafsson, Mats; Blomqvist, Goeran; Gudmundsson, Anders; Dahl, Andreas; Swietlicki, Erik; Bohgard, Mats; Lindbom, John; Ljungman, Anders

    2008-01-01

    In regions where studded tyres and traction material are used during winter, e.g. the Nordic countries, northern part of USA, Canada, and Japan, mechanically generated particles from traffic are the main reason for high particle mass concentrations in busy street and road environments. In many Nordic municipalities the European environmental quality standard for inhalable particles (PM 10 ) is exceeded due to these particles. In this study, particles from the wear of studded and studless friction tyres on two pavements and traction sanding were generated using a road simulator. The particles were characterized using particle sizers, Particle Induced X-Ray Emission Analysis and electron microscopy. Cell studies were conducted on particles sampled from the tests with studded tyres and compared with street environment, diesel exhaust and subway PM 10 , respectively. The results show that in the road simulator, where resuspension is minimized, studded tyres produce tens of times more particles than friction tyres. Chemical analysis of the sampled particles shows that the generated wear particles consist almost entirely of minerals from the pavement stone material, but also that Sulfur is enriched for the submicron particles and that Zink is enriched for friction tyres for all particles sizes. The chemical data can be used for source identification and apportionment in urban aerosol studies. A mode of ultra-fine particles was also present and is hypothesised to originate in the tyres. Further, traction material properties affect PM 10 emission. The inflammatory potential of the particles from wear of pavements seems to depend on type of pavement and can be at least as potent as diesel exhaust particles. The results imply that there is a need and a good potential to reduce particle emission from pavement wear and winter time road and street operation by adjusting both studded tyre use as well as pavement and traction material properties

  8. Effect of joint traction on functional improvement and quality of life in patients with severe knee osteoarthritis

    OpenAIRE

    Sedigheh Sadat Naeimee; Abbas Rahimi; Mehdi Rezaee; Alireza Akbarzadeh Baghban; Khosro Khademi Kalantari; ُSomayeh Mahmoudi Aghdam

    2012-01-01

    Background and aim: Osteoarthritis (OA) is the most prevalent joint disease in adults around the world and its incidence rises with age. Patients with severe knee osteoarthritis often complain of pain and severe functional disability. Most of conservative treatments used in this group of patients induce poor improvements. This study evaluated the effect of joint traction on quality of life of patients with severe knee osteoarthritis.Materials and Methods: In this clinical trial study, forty f...

  9. Performance Comparison between a Permanent Magnet Synchronous Motor and an Induction Motor as a Traction Motor for High Speed Train

    Science.gov (United States)

    Kondo, Minoru; Kawamura, Junya; Terauchi, Nobuo

    Performance tests are carried out to demonstrate the superiority of a permanent magnet synchronous motor to an induction motor as a traction motor for high-speed train. A prototype motor was manufactured by replacing the rotor of a conventional induction motor. The test results show that the permanent magnet motor is lighter, efficient and more silent than the induction motor because of the different rotor structure.

  10. Characterizing components of the Saw Palmetto Berry Extract (SPBE) on prostate cancer cell growth and traction

    International Nuclear Information System (INIS)

    Scholtysek, Carina; Krukiewicz, Aleksandra A.; Alonso, Jose-Luis; Sharma, Karan P.; Sharma, Pal C.; Goldmann, Wolfgang H.

    2009-01-01

    Saw Palmetto Berry Extract (SPBE) is applied for prostate health and treatment of urinary tract infections, nonbacterial prostitis and Benign Prostatic Hyperplasia (BPH) in man. An assumption is that SPBE affects tumor cell progression and migration in breast and prostate tissue. In this work, DU-145 cells were used to demonstrate that SPBE and its sterol components, β-sitosterol and stigmasterol, inhibit prostate cancer growth by increasing p53 protein expression and also inhibit carcinoma development by decreasing p21 and p27 protein expression. In the presence of cholesterol, these features are not only reversed but increased significantly. The results show for the first time the potential of SPBE, β-sitosterol and stigmasterol as potential anti-tumor agents. Since the protein p53 is also regarded as nuclear matrix protein facilitating actin cytoskeletal binding, 2D tractions were measured. The cell adhesion strength in the presence of SPBE, β-sitosterol and cholesterol and the observation was that the increase in p53 expression triggered an increase in the intracellular force generation. The results suggest a dual function of p53 in cells.

  11. Characterizing components of the Saw Palmetto Berry Extract (SPBE) on prostate cancer cell growth and traction.

    Science.gov (United States)

    Scholtysek, Carina; Krukiewicz, Aleksandra A; Alonso, José-Luis; Sharma, Karan P; Sharma, Pal C; Goldmann, Wolfgang H

    2009-02-13

    Saw Palmetto Berry Extract (SPBE) is applied for prostate health and treatment of urinary tract infections, nonbacterial prostitis and Benign Prostatic Hyperplasia (BPH) in man. An assumption is that SPBE affects tumor cell progression and migration in breast and prostate tissue. In this work, DU-145 cells were used to demonstrate that SPBE and its sterol components, beta-sitosterol and stigmasterol, inhibit prostate cancer growth by increasing p53 protein expression and also inhibit carcinoma development by decreasing p21 and p27 protein expression. In the presence of cholesterol, these features are not only reversed but increased significantly. The results show for the first time the potential of SPBE, beta-sitosterol and stigmasterol as potential anti-tumor agents. Since the protein p53 is also regarded as nuclear matrix protein facilitating actin cytoskeletal binding, 2D tractions were measured. The cell adhesion strength in the presence of SPBE, beta-sitosterol and cholesterol and the observation was that the increase in p53 expression triggered an increase in the intracellular force generation. The results suggest a dual function of p53 in cells.

  12. [Clinical observation on external humeral epicondylitis treated with back-rotation traction].

    Science.gov (United States)

    Fu, Rui-yang; Wang, Ya-ling; Gu, Zhong-zhong; Wang, Bao-hu; Zhu, Qi; Li, Ye; Wang, En-ping

    2009-02-01

    To evaluate the clinical effect of manipulation on external humeral epicondylitis, and to explore the functional mechanism and ideal treatment. Eighty-six patients who had been treated with acupuncture, obturation and needle-knife were divided into routine group and treatment group randomly. In routine group, there were 42 cases (male 13, female 29, means 40.8 years); and in treatment group there were 44 cases (male 16, female 28, means 41.2 years). There's no further treatment for the routine group after the therapy above, while the treatment group was added with back-rotation traction manipulation. Taking Verhaar therapy effect appraisal system of tennis-ball elbow to evaluate elbow function. After 7 days of therapy, the results were excellent in 13 cases, good in 16, fair in 4, poor in 9 in the routine group; and excellent in 38, good in 4 and fair in 2 in treatment group; and the effect in the treatment group were better than that of the routine group (P Making manipulation after routine acupuncture, local obturation and needle-knife has active meaning to remove trauma inflammation, prevent re-conglutination, promote recovery and prevent recurrence.

  13. Repair of Total Tractional Retinal Detachment in Norrie Disease: Report of Technique and Successful Surgical Outcome.

    Science.gov (United States)

    Todorich, Bozho; Thanos, Aristomenis; Yonekawa, Yoshihiro; Capone, Antonio

    2017-03-01

    Norrie disease is a rare, but devastating cause of pediatric retinal detachment, universally portending a poor visual prognosis. This paper describes successful surgical management of an infant with total retinal detachment associated with Norrie disease mutation. The infant was a full-term white male who presented with bilateral total funnel retinal detachments (RDs). He underwent genetic testing, which demonstrated single-point mutation 133 G>A transition in exon 2 of the NDP gene. The retinal detachment was managed with translimbal iridectomy, lensectomy, capsulectomy, and vitrectomy. Careful dissection of the retrolental membranes resulted in opening of the funnel. Single-stage surgery in this child's eye achieved re-attachment of the posterior pole with progressive reabsorption of subretinal fluid and cholesterol without the need for external drainage. Fluorescein angiography, performed at 2 months postoperatively, demonstrated perfusion of major vascular arcades, but with significant abnormalities and aneurysmal changes of higher-order vessels, suggestive of retinal and vascular dysplasia. The child has maintained brisk light perception vision. Early surgical intervention with careful dissection of tractional tissues can potentially result in good anatomic outcomes in some patients with Norrie disease-associated retinal detachment. [Ophthalmic Surg Lasers Imaging Retina. 2017;48:260-262.]. Copyright 2017, SLACK Incorporated.

  14. An Assessment of Vitreous Degeneration in Eyes with Vitreomacular Traction and Macular Holes

    Directory of Open Access Journals (Sweden)

    Quraish Ghadiali

    2017-01-01

    Full Text Available Purpose. To compare the stages of vitreous degeneration in patients with vitreomacular traction (VMT and macular holes (MH. Methods. A retrospective study was performed analyzing stages of vitreous degeneration of eyes with VMT or MH using swept-source optical coherence tomography (SS-OCT and spectral-domain optical coherence tomography (SD-OCT. An analogous review was performed on a control group of eyes with contralateral posterior vitreous detachments. Thirty-four eyes with VMT/MH and 39 control eyes were reviewed. Results. Twenty-seven VMT/MH eyes and 31 control eyes were included. Eyes with VMT/MH demonstrated significantly earlier stages of vitreous degeneration when compared to the control group (p=0.048 despite significantly greater age (p=0.032. Conclusions. Vitreoretinal interface disease is more often associated with a formed vitreous and an intact premacular bursa. This is contrary to previous assumptions implicating degeneration of vitreous as a precipitating factor of interface disease when in conjunction with abnormal vitreomacular separation.

  15. Function of Train Traction Department and Railway Vehicles in Logistic Centres

    Directory of Open Access Journals (Sweden)

    Velimir Kolar

    2007-05-01

    Full Text Available The increasing globalization has spread the production locationsto every part of the world thus increasing even more therole of transport in determining the price and quality of a product.Therefore, the producers and carriers join together moreand more frequently through the supply chains. Railway carriershave a very significant role in supply chains, both throughorganization of transport and forming the trains as final products,and through forming the logistic centres. Logistic centresare the starting and the final railway stations but also the meetingpoints of the national carrier with other carriers (sea, road,river as well as other railway carriers and they also represent informationcentres. For the quality of service at logistic centres, itis important to have well organized operation of train traction.In order to keep up the regulmity of trains and the quality oftransport at logistic centres, among other things, it is necessaryto provide an optimal number of locomotives and to providethe technical inspection place. Special attention should be paidto the organization of work peiformed by the engine staff At logisticcentres it is possible to organize high-quality technical inspectionof wagons thus increasing the traffic safety.

  16. Intergranular fracture in UO2: derivation of traction-separation law from atomistic simulations

    Energy Technology Data Exchange (ETDEWEB)

    Yongfeng Zhang; Paul C Millett; Michael R Tonks; Xian-Ming Bai; S Bulent Biner

    2013-10-01

    In this study, the intergranular fracture behavior of UO2 was studied by molecular dynamics simulations using the Basak potential. In addition, the constitutive traction-separation law was derived from atomistic data using the cohesive-zone model. In the simulations a bicrystal model with the (100) symmetric tilt E5 grain boundaries was utilized. Uniaxial tension along the grain boundary normal was applied to simulate Mode-I fracture. The fracture was observed to propagate along the grain boundary by micro-pore nucleation and coalescence, giving an overall intergranular fracture behavior. Phase transformations from the Fluorite to the Rutile and Scrutinyite phases were identified at the propagating crack tips. These new phases are metastable and they transformed back to the Fluorite phase at the wake of crack tips as the local stress concentration was relieved by complete cracking. Such transient behavior observed at atomistic scale was found to substantially increase the energy release rate for fracture. Insertion of Xe gas into the initial notch showed minor effect on the overall fracture behavior.

  17. A novel assessment of the traction forces upon settlement of two typical marine fouling invertebrates using PDMS micropost arrays

    Directory of Open Access Journals (Sweden)

    Kang Xiao

    2018-01-01

    Full Text Available Marine biofouling poses a severe threat to maritime and aquaculture industries. To prevent the attachment of marine biofouling organisms on man-made structures, countless cost and effort was spent annually. In particular, most attention has been paid on the development of efficient and environmentally friendly fouling-resistant coatings, as well as larval settlement mechanism of several major biofouling invertebrates. In this study, polydimethylsiloxane (PDMS micropost arrays were utilized as the settlement substrata and opposite tractions were identified during early settlement of the barnacle Amphibalanus amphitrite and the bryozoan Bugula neritina. The settling A. amphitrite pushed the periphery microposts with an average traction force of 376.2 nN, while settling B. neritina pulled the periphery microposts with an average traction force of 205.9 nN. These micropost displacements are consistent with the body expansion of A. amphitrite during early post-settlement metamorphosis stage and elevation of wall epithelium of B. neritina during early pre-ancestrula stage, respectively. As such, the usage of micropost array may supplement the traditional histological approach to indicate the early settlement stages or even the initiation of larval settlement of marine fouling organisms, and could finally aid in the development of automatic monitoring platform for the real-time analysis on this complex biological process.

  18. MR evaluation of the articular cartilage of the femoral head during traction. Correlation with resected femoral head

    Energy Technology Data Exchange (ETDEWEB)

    Nakanishi, K. [Osaka Seamens Insurance Hospital (Japan). Dept. of Radiology; Tanaka, H.; Narumi, Y.; Nakamura, H. [Osaka Univ. Medical School (Japan). Dept. of Radiology; Nishii, T.; Masuhara, K. [Osaka Univ. Medical School (Japan). Dept. of Orthopedic Surgery

    1999-01-01

    Objective: The purpose was to evaluate the articular cartilage of the hip joint with MR during traction and compare the findings with the resected specimen or arthroscopic findings. Material and Methods: Eight healthy volunteers, 5 patients with osteonecrosis, 5 with acetabular dysplasia, and 5 with advanced osteoarthrosis underwent MR imaging to evaluate the articular cartilage of the hip joint. Coronal fat-suppressed 3D spoiled gradient-echo (SPGR) images were obtained during traction. Identical imaging was performed of all the resected femoral heads of the osteonecrosis and advanced osteoarthrosis patients, and was correlated with the macroscopic pathological findings. Results: The traction was effective and the femoral articular cartilage was clearly identified in all 8 control subjects, and in all cases of osteonecrosis and acetabular dysplasia. In 4 cases of osteonecrosis, chondral fracture was identified in the boundary between the necrosis and the normal area. In all cases of advanced osteoarthrosis, cartilage was identified only at the medial side. The MR images of osteonecrosis and advanced osteoarthrosis corresponded well with the MR images of the resected femoral heads and the macroscopic findings. (orig.)

  19. Multiphoton photochemical crosslinking-based fabrication of protein micropatterns with controllable mechanical properties for single cell traction force measurements

    Science.gov (United States)

    Tong, Ming Hui; Huang, Nan; Zhang, Wei; Zhou, Zhuo Long; Ngan, Alfonso Hing Wan; Du, Yanan; Chan, Barbara Pui

    2016-01-01

    Engineering 3D microstructures with predetermined properties is critical for stem cell niche studies. We have developed a multiphoton femtosecond laser-based 3D printing platform, which generates complex protein microstructures in minutes. Here, we used the platform to test a series of fabrication and reagent parameters in precisely controlling the mechanical properties of protein micropillars. Atomic force microscopy was utilized to measure the reduced elastic modulus of the micropillars, and transmission electron microscopy was used to visualize the porosity of the structures. The reduced elastic modulus of the micropillars associated positively and linearly with the scanning power. On the other hand, the porosity and pore size of the micropillars associated inversely and linearly with the scanning power and reagent concentrations. While keeping the elastic modulus constant, the stiffness of the micropillars was controlled by varying their height. Subsequently, the single cell traction forces of rabbit chondrocytes, human dermal fibroblasts, human mesenchymal stem cells, and bovine nucleus pulposus cells (bNPCs) were successfully measured by culturing the cells on micropillar arrays of different stiffness. Our results showed that the traction forces of all groups showed positive relationship with stiffness, and that the chondrocytes and bNPCs generated the highest and lowest traction forces, respectively.

  20. High-Force Versus Low-Force Lumbar Traction in Acute Lumbar Sciatica Due to Disc Herniation: A Preliminary Randomized Trial.

    Science.gov (United States)

    Isner-Horobeti, Marie-Eve; Dufour, Stéphane Pascal; Schaeffer, Michael; Sauleau, Erik; Vautravers, Philippe; Lecocq, Jehan; Dupeyron, Arnaud

    This study compared the effects of high-force versus low-force lumbar traction in the treatment of acute lumbar sciatica secondary to disc herniation. A randomized double blind trial was performed, and 17 subjects with acute lumbar sciatica secondary to disc herniation were assigned to high-force traction at 50% body weight (BW; LT50, n = 8) or low force traction at 10% BW (LT10, n = 9) for 10 sessions in 2 weeks. Radicular pain (visual analogue scale [VAS]), lumbo-pelvic-hip complex motion (finger-to-toe test), lumbar-spine mobility (Schöber-Macrae test), nerve root compression (straight-leg-raising test), disability (EIFEL score), drug consumption, and overall evaluation of each patient were measured at days 0, 7, 1, 4, and 28. Significant (P sciatica secondary to disc herniation who received 2 weeks of lumbar traction reported reduced radicular pain and functional impairment and improved well-being regardless of the traction force group to which they were assigned. The effects of the traction treatment were independent of the initial level of medication and appeared to be maintained at the 2-week follow-up. Copyright © 2016. Published by Elsevier Inc.

  1. Usefulness of MR arthrography of the hip with leg traction in the evaluation of ligamentum teres injuries

    Energy Technology Data Exchange (ETDEWEB)

    Cerezal, Luis; Fernandez-Hernando, Moises [Department of Radiology, Diagnostico Medico Cantabria, Santander, Cantabria (Spain); Perez Carro, Luis [Learnig Trauma Med. Centro de Consultas Medicas CCM, Orthopedic Surgery department, Santander (Spain); Llorca, Javier [University of Cantabria - IDIVAL, Santander (Spain); CIBER Epidemiology and Public Health, Santander (Spain); Llopis, Eva [Alzira Hospital, Department of Radiology, Valencia (Spain); Montero, Juan Antonio [Cantabria University, Anatomy and Cell Biology, Santander (Spain); Canga, Ana [Cantabria University, Anatomy and Cell Biology, Santander (Spain); Department of Radiology Marques de Valdecilla University Hospital, Santander, Cantabria (Spain)

    2015-11-15

    To retrospectively evaluate the diagnostic accuracy of magnetic resonance (MR) arthrography of the hip with leg traction in the evaluation of ligamentum teres lesions and to evaluate whether there is increased articular distraction, possibly indicating secondary instability, in hips with ligamentum teres injuries. Institutional review board approval and informed consent were obtained for this retrospective study. MR arthrograms of the hip with leg traction of 184 consecutive patients, including 108 men (mean age, 32.6 years; range, 19-53 years) and 76 women (mean age, 38.5 years; range, 18-56 years), who underwent hip arthroscopy were assessed for the presence of ligamentum teres lesions. The MR arthrographic findings were independently assessed by two radiologists who were blinded to the arthroscopic results. The inclusion criteria stipulated no previous surgery, arthroscopy within 1 month after MR arthrography, and availability of a detailed surgical report with ligamentum teres findings. The arthroscopy findings served as the reference standard. Sensitivity, specificity, accuracy, and K statistics for interobserver and intraobserver agreement were calculated. At arthroscopy, 32 ligamentum teres injuries were found. The ligamentum teres was normal in 152 (82.6 %) patients and had suffered low-grade partial tears in 15 (8.1 %) patients, high-grade partial tears in 10 (5.4 %) patients, and complete ruptures in 7 (3.8 %) patients. MR arthrography with axial traction demonstrated moderate sensitivity and high specificity for both low-grade (62/93 %) and high-grade (66/96 %) partial tears. Grouping low- and high-grade partial tears increased the diagnostic performance of MR arthrography, yielding a sensitivity of 87 % and a specificity of 95 %. For complete ligamentum teres tears, MR arthrography with leg traction demonstrated high sensitivity (92 %) and specificity (98 %). Articular distraction was significantly increased in patients with complete ruptures of the

  2. Usefulness of MR arthrography of the hip with leg traction in the evaluation of ligamentum teres injuries

    International Nuclear Information System (INIS)

    Cerezal, Luis; Fernandez-Hernando, Moises; Perez Carro, Luis; Llorca, Javier; Llopis, Eva; Montero, Juan Antonio; Canga, Ana

    2015-01-01

    To retrospectively evaluate the diagnostic accuracy of magnetic resonance (MR) arthrography of the hip with leg traction in the evaluation of ligamentum teres lesions and to evaluate whether there is increased articular distraction, possibly indicating secondary instability, in hips with ligamentum teres injuries. Institutional review board approval and informed consent were obtained for this retrospective study. MR arthrograms of the hip with leg traction of 184 consecutive patients, including 108 men (mean age, 32.6 years; range, 19-53 years) and 76 women (mean age, 38.5 years; range, 18-56 years), who underwent hip arthroscopy were assessed for the presence of ligamentum teres lesions. The MR arthrographic findings were independently assessed by two radiologists who were blinded to the arthroscopic results. The inclusion criteria stipulated no previous surgery, arthroscopy within 1 month after MR arthrography, and availability of a detailed surgical report with ligamentum teres findings. The arthroscopy findings served as the reference standard. Sensitivity, specificity, accuracy, and K statistics for interobserver and intraobserver agreement were calculated. At arthroscopy, 32 ligamentum teres injuries were found. The ligamentum teres was normal in 152 (82.6 %) patients and had suffered low-grade partial tears in 15 (8.1 %) patients, high-grade partial tears in 10 (5.4 %) patients, and complete ruptures in 7 (3.8 %) patients. MR arthrography with axial traction demonstrated moderate sensitivity and high specificity for both low-grade (62/93 %) and high-grade (66/96 %) partial tears. Grouping low- and high-grade partial tears increased the diagnostic performance of MR arthrography, yielding a sensitivity of 87 % and a specificity of 95 %. For complete ligamentum teres tears, MR arthrography with leg traction demonstrated high sensitivity (92 %) and specificity (98 %). Articular distraction was significantly increased in patients with complete ruptures of the

  3. Esophageal Endoscopic Submucosal Dissection Assisted by an Overtube with a Traction Forceps: An Animal Study

    Directory of Open Access Journals (Sweden)

    Ken Ohata

    2016-01-01

    Full Text Available Esophageal endoscopic submucosal dissection (ESD is technically difficult. To make it safer, we developed a novel method using overtube with a traction forceps (OTF for countertraction during submucosal dissection. We conducted an ex vivo animal study and compared the clinical outcomes between OTF-ESD and conventional method (C-ESD. A total of 32 esophageal ESD procedures were performed by four beginner and expert endoscopists. After circumferential mucosal incision for the target lesion, structured as the isolated pig esophagus 3 cm long, either C-ESD or OTF-ESD was randomly selected for submucosal dissection. All the ESD procedures were completed as en bloc resections, while perforation only occurred in a beginner’s C-ESD procedure. The dissection time for OTF-ESD was significantly shorter than that for C-ESD for both the beginner and expert endoscopists (22.8±8.3 min versus 7.8±4.5 min, P<0.001, and 11.3±4.4 min versus 5.9±2.5 min, P=0.01, resp.. The frequency and volume of the submucosal injections were significantly smaller for OTF-ESD than for C-ESD (1.3±0.6 times versus 2.9±1.5 times, P<0.001, and 5.3±2.8 mL versus 15.6±7.3 mL, P<0.001, resp.. Histologically, muscular injury was more common among the C-ESD procedures (80% versus 13%, P=0.009. Our results indicated that the OTF-ESD technique is useful for the safe and easy completion of esophageal ESD.

  4. Plantar calcaneal spurs in older people: longitudinal traction or vertical compression?

    Directory of Open Access Journals (Sweden)

    Landorf Karl B

    2008-08-01

    Full Text Available Abstract Background Plantar calcaneal spurs are common, however their pathophysiology is poorly understood. This study aimed to evaluate the prevalence and correlates of plantar calcaneal spurs in a large sample of older people. Methods Weightbearing lateral foot radiographs of 216 people (140 women and 76 men aged 62 to 94 years (mean age 75.9, SD 6.6 were examined for plantar calcaneal and Achilles tendon spurs. Associations between the presence of spurs and sex, body mass index, radiographic measures of foot posture, self-reported co-morbidities and current or previous heel pain were then explored. Results Of the 216 participants, 119 (55% had at least one plantar calcaneal spur and 103 (48% had at least one Achilles tendon spur. Those with plantar calcaneal spurs were more likely to have Achilles tendon spurs (odds ratio [OR] = 2.0, 95% confidence interval [CI] 1.2 to 3.5. Prevalence of spurs did not differ according to sex. Participants with plantar calcaneal spurs were more likely to be obese (OR = 7.9, 95% CI 3.6 to 17.0, report osteoarthritis (OR = 2.6, 95% CI 1.6 to 4.8 and have current or previous heel pain (OR = 4.6, 95% CI 2.3 to 9.4. No relationship was found between the presence of calcaneal spurs and radiographic measures of foot posture. Conclusion Calcaneal spurs are common in older men and women and are related to obesity, osteoarthritis and current or previous heel pain, but are unrelated to radiographic measurements of foot posture. These findings support the theory that plantar calcaneal spurs may be an adaptive response to vertical compression of the heel rather than longitudinal traction at the calcaneal enthesis.

  5. Review of economic studies and budget impact analysis of ocriplasmin as a treatment of vitreomacular traction.

    Science.gov (United States)

    García-Pérez, L; Abreu-González, R; Pérez-Ramos, J; García-Pérez, S; Serrano-Aguilar, P

    2016-06-01

    To review the evidence on the cost-effectiveness of ocriplasmin as a treatment for vitreomacular traction (VMT), and to estimate the impact on the Spanish National Health System (NHS). 1) Systematic review. The following databases were searched in January 2015: MEDLINE, PREMEDLINE, EMBASE, CRD, the Cochrane Library, and key websites. Selection criteria were: full economic evaluations that compared ocriplasmin with usual care ('watch and wait' and/or vitrectomy) in patients with VMT. The outcomes to extract were costs of the alternatives and the incremental cost-effectiveness ratio. Studies of budget impact analysis were also included. The methodological quality was assessed, and a narrative synthesis of the included studies was carried out. 2) Estimation of budget impact. The impact on the budget as a result of the introduction of ocriplasmin in the NHS was estimated, including data from different sources. Six studies were identified, none of them performed in Spain. The two best studies concluded that ocriplasmin is cost-effective in their respective countries (Canada and United Kingdom), but only in patients with certain conditions (without epiretinal membrane, for example). The results of the budget impact analysis are different between countries. The analysis for Spain showed that the introduction of ocriplasmin would mean a saving over 1 million Euros for the NHS in 5 years. The cost-effectiveness of ocriplasmin has not been demonstrated in Spain. However, good studies performed in other countries found that ocriplasmin is cost-effective in selected patients. Given the current prices in Spain, ocriplasmin could involve a saving for the Spanish NHS. Copyright © 2016 Sociedad Española de Oftalmología. Published by Elsevier España, S.L.U. All rights reserved.

  6. Detecting tangential dislocations on planar faults from traction free surface observations

    International Nuclear Information System (INIS)

    Ionescu, Ioan R; Volkov, Darko

    2009-01-01

    We propose in this paper robust reconstruction methods for tangential dislocations on planar faults. We assume that only surface observations are available, and that a traction free condition applies at that surface. This study is an extension to the full three dimensions of Ionescu and Volkov (2006 Inverse Problems 22 2103). We also explore in this present paper the possibility of detecting slow slip events (such as silent earthquakes, or earthquake nucleation phases) from GPS observations. Our study uses extensively an asymptotic estimate for the observed surface displacement. This estimate is first used to derive what we call the moments reconstruction method. Then it is also used for finding necessary conditions for a surface displacement field to have been caused by a slip on a fault. These conditions lead to the introduction of two parameters: the activation factor and the confidence index. They can be computed from the surface observations in a robust fashion. They indicate whether a measured displacement field is due to an active fault. We also infer a second, combined, reconstruction technique blending least square minimization and the moments method. We carefully assess how our reconstruction method is affected by the sensitivity of the observation apparatus and the stepsize for the grid of surface observation points. The maximum permissible stepsize for such a grid is computed for different values of fault depth and orientation. Finally we present numerical examples of reconstruction of faults. We demonstrate that our combined method is sharp, robust and computationally inexpensive. We also note that this method performs satisfactorily for shallow faults, despite the fact that our asymptotic formula deteriorates in that case

  7. Four-port bimanual 23-gauge vitrectomy for diabetic tractional retinal detachment.

    Science.gov (United States)

    Wang, Zhao-Yang; Zhao, Ke-Ke; Li, Jia-Kai; Rossmiller, Brian; Zhao, Pei-Quan

    2016-06-01

    Four-port bimanual vitrectomy is a surgical technique that facilitates removal of epiretinal membranes in severe proliferative diabetic retinopathy (PDR). As the illumination is held by the assistant through the fourth scleral incision, fibrovascular membranes are removed by bimanual manipulation techniques. The objective of this study was to evaluate the safety and efficacy of four-port bimanual 23-gauge vitrectomy for patients with tractional retinal detachment (TRD) in severe PDR. Retrospective, comparative, consecutive, interventional case series. Sixty-six eyes of 58 consecutive patients who underwent primary vitrectomy for severe diabetic TRD. Thirty-six eyes of 31 cases that were treated with four-port 23-gauge vitrectomy were compared with 30 eyes of 27 cases that were treated with 23-gauge pars plana vitrectomy (PPV). Main outcome measures were best-corrected visual acuity (BCVA), retinal status, intraocular pressure, and incidence of intraoperative and postoperative complications with at least 6 months of follow-up. The primary and ultimate anatomic success rates (94.4% versus 93.3%, and 100% in both groups, respectively) and the mean BCVA changes did not differ significantly between groups. The whole surgical time and the membrane removal time were significantly (p four-port 23-gauge group than in the 23-gauge group. There was no difference in the incidence of intraoperative and postoperative complications in both groups. Four-port bimanual 23-gauge vitrectomy offers comparable anatomic success and shortens the surgical time compared with conventional 23-gauge PPV in patients with TRD resulting from severe PDR. © 2016 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

  8. Device for lengthening of a musculotendinous unit by direct continuous traction in the sheep

    Directory of Open Access Journals (Sweden)

    Zumstein Matthias A

    2012-05-01

    Full Text Available Abstract Background Retraction, atrophy and fatty infiltration are signs subsequent to chronic rotator cuff tendon tears. They are associated with an increased pennation angle and a shortening of the muscle fibers in series. These deleterious changes of the muscular architecture are not reversible with current repair techniques and are the main factors for failed rotator cuff tendon repair. Whereas fast stretching of the retracted musculotendinous unit results in proliferation of non-contractile fibrous tissue, slow stretching may lead to muscle regeneration in terms of sarcomerogenesis. To slowly stretch the retracted musculotendinous unit in a sheep model, two here described tensioning devices have been developed and mounted on the scapular spine of the sheep using an expandable threaded rod, which has been interposed between the retracted tendon end and the original insertion site at the humeral head. Traction is transmitted in line with the musculotendinous unit by sutures knotted on the expandable threaded rod. The threaded rod of the tensioner is driven within the body through a rotating axis, which enters the body on the opposite side. The tendon end, which was previously released (16 weeks prior from its insertion site with a bone chip, was elongated with a velocity of 1 mm/day. Results After several steps of technical improvements, the tensioner proved to be capable of actively stretching the retracted and degenerated muscle back to the original length and to withstand the external forces acting on it. Conclusion This technical report describes the experimental technique for continuous elongation of the musculotendinous unit and reversion of the length of chronically shortened muscle.

  9. Intermittent Cervical Traction for Treating Neck Pain: A Meta-analysis of Randomized Controlled Trials.

    Science.gov (United States)

    Yang, Jheng-Dao; Tam, Ka-Wai; Huang, Tsai-Wei; Huang, Shih-Wei; Liou, Tsan-Hon; Chen, Hung-Chou

    2017-07-01

    A meta-analysis. The aim of this study was to perform a comprehensive search of current literature and conduct a meta-analysis of randomized controlled trials (RCTs) to assess the neck pain relieving effect of intermittent cervical traction (ICT). Neck pain is a common and disabling problem with a high prevalence in general population. It causes a considerable burden on the health care system with a substantial expenditure. ICT is a common component of physical therapy for neck pain in the outpatient clinic. However, the evidence regarding the effectiveness of ICT for neck pain is insufficient. Data were obtained from the PubMed, Cochrane Library, Embase, and Scopus databases from the database inception date to July 02, 2016. RCTs reporting the effects of ICT on neck pain, including those comparing the effects of ICT with those of a placebo treatment, were included. Two reviewers independently reviewed the studies, conducted a risk of bias assessment, and extracted data. The data were pooled in a meta-analysis by using a random-effects model. The meta-analysis included seven RCTs. The results indicated that patients who received ICT for neck pain had significantly lower pain scores than those receiving placebos did immediately after treatment (standardized mean difference = -0.26, 95% confidence interval = -0.46 to -0.07). The pain scores during the follow-up period and the neck disability index scores immediately after treatment and during the follow-up period did not differ significantly. ICT may have a short-term neck pain-relieving effect. Some risks of bias were noted in the included studies, reducing the evidence level of this meta-analysis. Additional high-quality RCTs are required to clarify the long-term effects of ICT on neck pain. 1.

  10. Retrospective analysis of a VACM (vacuum-assisted closure and mesh-mediated fascial traction treatment manual for temporary abdominal wall closure – results of 58 consecutive patients

    Directory of Open Access Journals (Sweden)

    Beltzer, Christian

    2016-07-01

    Full Text Available Introduction: The optimal treatment concept for temporary abdominal closure (TAC in critically ill visceral surgery patients with open abdomen (OA continues to be unclear. The VACM (vacuum-assisted closure and mesh-mediated fascial traction therapy seems to permit higher delayed primary fascial closure rates (FCR than other TAC procedures. Material and methods: Patients of our clinic (n=58 who were treated by application of a VAC/VACM treatment manual in the period from 2005 to 2008 were retrospectively analysed. Results: The overall FCR of all patients was 48.3% (95% confidence interval: 34.95–61.78. An FCR of 61.3% was achieved in patients who had a vicryl mesh implanted at the fascial level (VACM therapy in the course of treatment. Mortality among patients treated with VACM therapy was 45.2% (95% CI: 27.32–63.97.Conclusions: The results of our own study confirm the results of previous studies which showed an acceptable FCR among non-trauma patients who were treated with VACM therapy. VACM therapy currently appears to be the treatment regime of choice for patients with OA requiring TAC.

  11. A few discussion on expert system development for electrical power systems-optimization of an inverter-motor of a railway traction chain

    International Nuclear Information System (INIS)

    Fezzani, D.; Piquet, H.; Foch, H.

    1998-01-01

    This paper deals with the automatic design of static converters and electrical machines. Facing the multitude of such devices (converters-machines), the choice of the appropriate converter or machine is a delicate problem. A high level of expertise is required to determine the best structure for the considered application. This choice could be rapidly made if one had a system which incorporates a great knowledge of converters, machines and control methods. Firstly, the authors review the realized studies, then they propose this methodology for a concrete case in order to optimize an inverter-motor of a railway traction chain. Constraints are described in terms of input and output performances (losses, current,..). These data are analyzed by using design rules and methods which allow the decrease of the manufacture cost of the inverter-motor. Rules and methods are implemented on a workstation by means of an ''expert system shell'' SMECI. The article proposes several tracks which involve organization, methodology, confirmation and implementation of a tool supporting a method. This process of implementation is the most efficient to fit into a constant process of improvement which is supported by the return on experience and by the evolution of the state of the art. (orig.)

  12. Control algorithms for single inverter dual induction motor system applied to railway traction; Commande algorithmique d'un systeme mono-onduleur bimachine asynchrone destine a la traction ferroviaire

    Energy Technology Data Exchange (ETDEWEB)

    Pena Eguiluz, R.

    2002-11-15

    The goal of this work concerns the modelling and the behaviour characterisation of a single inverter dual induction motor system applied to a railway traction bogie (BB36000) in order to concept its control. First part of this job is dedicated to the detailed description of overall system. The influence analysis of the internal perturbations (motor parameters variation) and, external perturbations (pantograph detachment, adherence loss, stick-slip) of the system have made considering the field oriented control applied to each motor of the bogie (classical traction structure). vi In a second part, a novel propulsion structure is proposed. It is composed by a single pulse-width modulated two level voltage source inverter. It supplies two parallel connected induction motors, which generate the transmitted traction force to the bogie wheels. The locomotive case represents the common load for the two motors. Several co-operative control strategies (CS) are studied. They are: the mean CS, the double mean CS, the master - slave switched CS and, the mean differential CS. In addition, an appropriated electric modes observer structure for these different controls has studied. These controls have validated applying the perturbations to the models using the solver SABER. This special approach is equivalent to quasi-experimentation, because the mechanical and the electrical system components have modelled using MAST language and, the sample control has created by a C code programme in the SABER environment. Third part is dedicated to the mechanical sensor suppression and, its adaptation in the cooperative control strategies. The partial speed reconstruction methods are: the fundamental frequency relation, the mechanical Kalman filter, the variable structure observer and the MRAS. Finally, the hardware system configuration of the experimental realisation is described. (author)

  13. MATHEMATIC SIMULATION OF TRANSIENT PROCESS IN A.C. – SYSTEM “ELECTRIC TRACTION NETWORK – LOCOMOTIVE” 1. SWITCH ON LOCOMOTIVE’S POWER CONVERTER IN “FREE PLAY” MODE; PARAMETERS ESTIMATION

    Directory of Open Access Journals (Sweden)

    T. M. Mishchenko

    2010-11-01

    Full Text Available In the article the electric circuit of substitution and mathematical model of the system of alternating current «traction substation − traction mains − electric locomotive DS 3» at switching its power transformer on in the idle mode are presented. Numerical determinations of parameters of traction substation, rails, contact network and transformer are executed; in so doing a special attention is paid to the estimation of dispersion inductance for the primary winding of transformer.

  14. MATHEMATIC SIMULATION OF TRANSIENT PROCESS IN A.C. – SYSTEM “ELECTRIC TRACTION NETWORK – LOCOMOTIVE” 1. SWITCH ON LOCOMOTIVE’S POWER CONVERTER IN “FREE PLAY” MODE; PARAMETERS ESTIMATION

    OpenAIRE

    T. M. Mishchenko; A. I. Kiiko

    2010-01-01

    In the article the electric circuit of substitution and mathematical model of the system of alternating current «traction substation − traction mains − electric locomotive DS 3» at switching its power transformer on in the idle mode are presented. Numerical determinations of parameters of traction substation, rails, contact network and transformer are executed; in so doing a special attention is paid to the estimation of dispersion inductance for the primary winding of transformer.

  15. A tissue adaptation model based on strain-dependent collagen degradation and contact-guided cell traction.

    Science.gov (United States)

    Heck, T A M; Wilson, W; Foolen, J; Cilingir, A C; Ito, K; van Donkelaar, C C

    2015-03-18

    Soft biological tissues adapt their collagen network to the mechanical environment. Collagen remodeling and cell traction are both involved in this process. The present study presents a collagen adaptation model which includes strain-dependent collagen degradation and contact-guided cell traction. Cell traction is determined by the prevailing collagen structure and is assumed to strive for tensional homeostasis. In addition, collagen is assumed to mechanically fail if it is over-strained. Care is taken to use principally measurable and physiologically meaningful relationships. This model is implemented in a fibril-reinforced biphasic finite element model for soft hydrated tissues. The versatility and limitations of the model are demonstrated by corroborating the predicted transient and equilibrium collagen adaptation under distinct mechanical constraints against experimental observations from the literature. These experiments include overloading of pericardium explants until failure, static uniaxial and biaxial loading of cell-seeded gels in vitro and shortening of periosteum explants. In addition, remodeling under hypothetical conditions is explored to demonstrate how collagen might adapt to small differences in constraints. Typical aspects of all essentially different experimental conditions are captured quantitatively or qualitatively. Differences between predictions and experiments as well as new insights that emerge from the present simulations are discussed. This model is anticipated to evolve into a mechanistic description of collagen adaptation, which may assist in developing load-regimes for functional tissue engineered constructs, or may be employed to improve our understanding of the mechanisms behind physiological and pathological collagen remodeling. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. Inverted Nipple Correction with Selective Dissection of Lactiferous Ducts Using an Operative Microscope and a Traction Technique.

    Science.gov (United States)

    Sowa, Yoshihiro; Itsukage, Sizu; Morita, Daiki; Numajiri, Toshiaki

    2017-10-01

    An inverted nipple is a common congenital condition in young women that may cause breastfeeding difficulty, psychological distress, repeated inflammation, and loss of sensation. Various surgical techniques have been reported for correction of inverted nipples, and all have advantages and disadvantages. Here, we report a new technique for correction of an inverted nipple using an operative microscope and traction that results in low recurrence and preserves lactation function and sensation. Between January 2010 and January 2013, we treated eight inverted nipples in seven patients with selective lactiferous duct dissection using an operative microscope. An opposite Z-plasty was added at the junction of the nipple and areola. Postoperatively, traction was applied through an apparatus made from a rubber gasket attached to a sterile syringe. Patients were followed up for 15-48 months. Adequate projection was achieved in all patients, and there was no wound dehiscence or complications such as infection. Three patients had successful pregnancies and subsequent breastfeeding that was not adversely affected by the treatment. There was no loss of sensation in any patient during the postoperative period. Our technique for treating an inverted nipple is effective and preserves lactation function and nipple sensation. The method maintains traction for a longer period, which we believe increases the success rate of the surgery for correction of severely inverted nipples. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

  17. Hamburg subway vehicles with new control and traction systems; Hamburger U-Bahn-Fahrzeuge mit neuer Leit- und Antriebstechnik

    Energy Technology Data Exchange (ETDEWEB)

    Polster, H.J.; Lehr, G.; Werner-Wieland, P. [Bombardier Transportation, LRV, Mannheim (Germany)

    2007-07-01

    With a view to testing new technologies for future vehicle series for the Hamburg subway network, the last 17 DT4 cars to be delivered under a current contract were equipped with the latest generation of control and traction systems. A MITRAC control system was installed instead of the MICAS-S type used in the DT4 vehicles delivered before. The GTO converters were replaced by IGBT elements. The concept is designed to allow for the change-over of DT4 vehicles of previous series to the new system. (orig.)

  18. 3.0T MR imaging of the ankle: Axial traction for morphological cartilage evaluation, quantitative T2 mapping and cartilage diffusion imaging-A preliminary study.

    Science.gov (United States)

    Jungmann, Pia M; Baum, Thomas; Schaeffeler, Christoph; Sauerschnig, Martin; Brucker, Peter U; Mann, Alexander; Ganter, Carl; Bieri, Oliver; Rummeny, Ernst J; Woertler, Klaus; Bauer, Jan S

    2015-08-01

    To determine the impact of axial traction during high resolution 3.0T MR imaging of the ankle on morphological assessment of articular cartilage and quantitative cartilage imaging parameters. MR images of n=25 asymptomatic ankles were acquired with and without axial traction (6kg). Coronal and sagittal T1-weighted (w) turbo spin echo (TSE) sequences with a driven equilibrium pulse and sagittal fat-saturated intermediate-w (IMfs) TSE sequences were acquired for morphological evaluation on a four-point scale (1=best, 4=worst). For quantitative assessment of cartilage degradation segmentation was performed on 2D multislice-multiecho (MSME) SE T2, steady-state free-precession (SSFP; n=8) T2 and SSFP diffusion-weighted imaging (DWI; n=8) images. Wilcoxon-tests and paired t-tests were used for statistical analysis. With axial traction, joint space width increased significantly and delineation of cartilage surfaces was rated superior (Pevaluation were smaller. Subchondral bone evaluation, motion artifacts and image quality were not significantly different between the acquisition methods (P>0.05). T2 values were lower at the tibia than at the talus (P<0.001). Reproducibility was better for images with axial traction. Axial traction increased the joint space width, allowed for better visualization of cartilage surfaces and improved compartment discrimination and reproducibility of quantitative cartilage parameters. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  19. Quantitative analysis of the orthodontic and orthopedic effects of maxillary traction.

    Science.gov (United States)

    Baumrind, S; Korn, E L; Isaacson, R J; West, E E; Molthen, R

    1983-11-01

    This article analyzes differences in displacement of ANS and of the upper first molar when different vectors of force are delivered to the maxilla in non-full-banded Phase I mixed-dentition treatment of Class II malocclusion. The sample is identical to that for which we have previously reported differences in change in several key measures of mandibular and facial shape. It includes a cervical-traction group, a high-pull-to-upper-molar group, a modified-activator group, and an untreated Class II control group. Using newly developed computer-conducted procedures, which are described, we have been able to partition the orthodontic and orthopedic components of upper molar displacement and also to isolate treatment effects from those attributable to spontaneous growth and development. In the region of ANS, small but statistically significant and clinically meaningful differences were noted between treatments. When the intercurrent effects of growth and development had been factored out (Table III), orthopedic distal displacement of ANS was significantly greater in the high-pull and cervical groups than in the activator group. Orthopedic downward displacement of ANS was seen to be significantly greater in the cervical group than in the high-pull and activator groups. In the region of the first molar cusp, mean distal displacement of the tooth as an orthopedic effect was found to be almost identical in the cervical and high-pull groups (although variability was greater in the cervical group), but the mean orthodontic effect was significantly greater in the high-pull group than in the cervical group. In the cervical group, where relatively light forces were used for relatively long treatment periods on average, more of the total distal displacement of the upper molar was of an orthopedic character than of an orthodontic character. Conversely, in the high-pull group, in which relatively heavier forces tended to be used for briefer treatment periods, most of the distal

  20. AUTOMATED MEASURING COMPLEX FOR ACCEPTANCE TESTING OF DC AND UNDULATED-CURRENT TRACTION MOTORS

    Directory of Open Access Journals (Sweden)

    A. Yu. Drubetskyi

    2016-12-01

    Full Text Available Purpose. In the paper it is necessary: 1 to familiarize the reader with the modern classification of measurement and diagnostics, familiarize with problems of automating the measurement of basic parameters during program execution of qualification tests of traction motors; 2 to make recommendations to improve the measurement ac-curacy, reduce labor intensity of work for carrying out measurements, and reduce the requirements for the qualification of the staff; 3 to provide practical implementation of measurement system, built on the basis of the practical recommendations contained in the article. Methodology. The work presents the classification of measurement and diagnostic tools. The author considered a list of equipment that can be used in measurement systems, as well as third-party options for measuring complex and measuring complex using stand management system. Their functional schemes were proposed. The author compared the advantages and disadvantages of these schemes to make recommendations on areas of their optimal use. Findings. Having analyzed the functional scheme of measuring systems, it was found that the use of the control system microcontroller as a measuring complex is expedient if the measurements have largely a test process control function. The use of a third-party measuring complex is more appropriate in cases when it is required: to eliminate dependence on the stand management system, to provide high mobility and reduce the requirements for the qualification of the staff. Originality. The work presents a brief over-view of the measurement means. The author developed the functional schemes of measuring systems using stand management system and third-party measuring complex, proposed the criteria for evaluating their optimal use. Practical value. Based on the proposed functional diagram, the measuring system on National Instruments hard-ware and software basis was set up. The sensors by LEM Company were used as primary

  1. CALCULATION OF MAGNETIC CHARACTERISTICS OF TRACTION ELECTRIC ENGINE WITH THE USE OF IMPROVED UNIVERSAL MAGNETIC CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    A. Y. Drubetskyi

    2017-06-01

    Full Text Available Purpose. The article is aimed to develop a technique for calculating the magnetic characteristics of uncompensated traction electric motors (TEM at any degree of attenuation of excitation based on the approximating expression for improved universal magnetic characteristics (UMC. It is also necessary to conduct an analysis of expressions for improved UMC with the aim of finding an expression that most fully satisfies the requirements for developing a technique for determining the inductive parameters of TEM. Methodology. It is necessary to determine the saturation coefficient for each degree of attenuation of the excitation for building the characteristics with the improved UMC. This can only be done analytically. To simplify the analytical finding of the saturation coefficient, the method based on solving a system of two equations is proposed, one of which is UMC itself, and the second one is a straight line whose angular coefficient is proportional to the saturation coefficient. Resulting values of the saturation coefficient for the excitation degrees β < 1 are essentially the coefficients of the shape of the magnetic characteristic. To get rid of the need to determine the coefficients of approximation each time in the calculation of characteristics a form of improved UMC is proposed, in which the magnetomotive force (MMF of the excitation winding serves as the argument's role. Findings. Using the improved UMC it is possible to calculate the characteristics of uncompensated TEMs for any degree of attenuation of excitation. The accuracy of the calculation at β = 1 does not differ from that in the calculation for UMC, proposed by Prof. M. D. Nakhodkin. The same accuracy is preserved at excitation degrees that are different from unity. Originality. An analytical technique for calculating the magnetic (speed characteristics of uncompensated TEM for any degree of attenuation with the help of an improved UMC is proposed. The analytical technique

  2. The influence of battery degradation level on the selected traction parameters of a light-duty electric vehicle

    Science.gov (United States)

    Juda, Z.; Noga, M.

    2016-09-01

    The article describes results of an analysis of the impact of degradation level of battery made in lead-acid technology on selected traction parameters of an electric light duty vehicle. Lead-acid batteries are still used in these types of vehicles. They do not require complex systems of performance management and monitoring and are easy to maintaining. Despite the basic disadvantage, which is the low value of energy density, low price is a decisive factor for their use in low-speed electric vehicles. The process of aging of the battery related with an increase in internal resistance of the cells and the loss of electric capacity of the battery was considered. A simplified model of cooperation of the DC electric motor with the battery assuming increased internal resistance was presented. In the paper the results of comparative traction research of the light-duty vehicle equipped with a set of new batteries and set of batteries having a significant degradation level were showed. The analysis of obtained results showed that the correct exploitation of the battery can slow down the processes of degradation and, thus, extend battery life cycle.

  3. Loss Characteristics of 6.5 kV RC-IGBT Applied to a Traction Converter

    Directory of Open Access Journals (Sweden)

    Xianjin Huang

    2017-07-01

    Full Text Available 6.5 kV level IGBT (Insulated Gate Bipolar Transistor modules are widely applied in megawatt locomotive (MCUs traction converters, to achieve an upper 3.5 kV DC link, which is beneficial for decreasing power losses and increasing the power density. Reverse Conducting IGBT (RC-IGBT constructs the conventional IGBT function and freewheel diode function in a single chip, which has a greater flow ability in the same package volume. In the same cooling conditions, RC-IGBT allows for a higher operating temperature. In this paper, a mathematic model is developed, referring to the datasheets and measurement data, to study the 6.5 kV/1000 A RC-IGBT switching features. The relationship among the gate desaturated pulse, conducting losses, and recovery losses is discussed. Simulations and tests were carried out to consider the influence of total losses on the different amplitudes and durations of the desaturated pulse. The RC-IGBT traction converter system with gate pulse desaturated control is built, and the simulation and measurements show that the total losses of RC-IGBT with desaturated control decreased comparing to the RC-IGBT without desaturated control or conventional IGBT. Finally, a proportional small power platform is developed, and the test results prove the correction of the theory analysis.

  4. Posterior axilla sling traction for shoulder dystocia: case review and a new method of shoulder rotation with the sling.

    Science.gov (United States)

    Cluver, Catherine Anne; Hofmeyr, G Justus

    2015-06-01

    The purpose of this study was to report on all cases in which posterior axilla sling traction (PAST) has been used to deliver cases of intractable shoulder dystocia and to describe a new method of shoulder rotation with the sling. A record of all published and known cases was collected that included information on preliminary obstetric techniques that were used and how the PAST technique was performed. Maternal outcomes that included maternal injury and length of hospital stay and fetal outcomes, which included birthweight, Apgar scores, nerve injuries, fractures, hospital stay, and outcome, were documented. We have recorded 19 cases where PAST has been used. In 5 cases, the babies had died in utero. Ten were assisted deliveries. PAST was successful in 18 cases. In one case, it was partially successful because it enabled delivery of the posterior shoulder with digital axillary traction. The most commonly used material was suction tubing. Once the posterior shoulder was delivered, the shoulder dystocia was resolved in all cases. Time from insertion to delivery was dystocia fail. Advantages are that it is easy to use (even by someone who has not seen it used previously), that the sling material is readily available, and that it is inserted quickly with 2 fingers. This is the first report of its use to rotate the posterior shoulder to the anterior position for delivery. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. Closed reduction of displaced or dislocated mandibular condyle fractures in children using threaded Kirschner wire and external rubber traction.

    Science.gov (United States)

    Kim, J H; Nam, D H

    2015-10-01

    Most surgeons agree that closed treatment provides the best results for condylar fractures in children. Nevertheless, treatment of the paediatric mandibular condyle fracture that is severely displaced or dislocated is controversial. The purpose of this study was to investigate the long-term clinical and radiological outcomes following the treatment of displaced or dislocated condylar fractures in children using threaded Kirschner wire and external rubber traction. This procedure can strengthen the advantage of closed reduction and make up for the shortcomings of open reduction. From March 1, 2005 to December 25, 2011, 11 children aged between 4 and 12 years with displaced or dislocated mandibular condyle fractures were treated using threaded Kirschner wire and external rubber traction under portable C-arm fluoroscopy. All patients had unilateral displaced or dislocated condylar fractures. The follow-up period ranged from 24 to 42 months (mean 29.3 months). Normal occlusion and pain-free function of the temporomandibular joint, without deviation or limitation of jaw opening, was achieved in all patients. This closed reduction technique in displaced or dislocated condylar fractures in children offers a reliable solution in preventing the unfavourable sequelae of closed treatment and the open technique, such as altered morphology, functional disturbances, and facial nerve damage. Copyright © 2015 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  6. Theory of rubber friction and traction properties of car tyres; Theorie der Gummireibung und Traktionseigenschaften von Reifen

    Energy Technology Data Exchange (ETDEWEB)

    Klueppel, M.; Alshuth, T.; Schuster, R.H. [Deutsches Inst. fuer Kautschuktechnologie e.V., Hannover (Germany)

    1998-12-31

    ABS braking on dry and wet roads involves different mechanisms of rubber friction on rough surfaces. This improves car safety in terms of higher manoeuvrability and shorter braking lengths especially on wet roads. Current research focuses on optimisation of tyrecontact surface materials with better traction characteristics and lower rolling resistance. Laboratory predictions of the traction properties of tyre faces must be based on fundamental knowledge of the local sliding phenomena in the tyre contact surface and the resulting energy dissipation during ABS braking. This contribution therefore attempts to relate the elementary mechanisms of tyre mechanics in ABS braking processes to theoretical concepts of rubber friction on rough surfaces. [Deutsch] Beim ABS-Bremsen auf trockenen und nassen Strassen werden unterschiedliche Mechanismen der Gummireibung auf rauhen Oberflaechen wirksam. In der Summe bewirkt dies eine hoehere Fahrsicherheit, da neben der Manoevrierfaehigkeit des Autos auch der Bremsweg, vor allem auf nassen Strassen, verkuerzt sein kann. In diesem Zusammenhang wird zur Zeit verstaerkt an einer Optimierung von Laufflaechenmaterialien durch den Einsatz von massgeschneiderten Loesungs-SBR-Typen in Verbindung mit gefaellten Kieselsaeuren gearbeitet, wodurch neben einer Verbesserung der Traktionseigenschaften beim ABS-Bremsen auch eine Verringerung des Rollwiderstandes erreicht wird. Fuer Laborvorhersagen der Traktionseigenschaften von Reifenlaufflaechen ist ein grundlegendes Verstaendnis der lokalen Gleitphaenomene in der Reifenaufstandsflaeche und der damit verbundenen Energiedissipation beim ABS-Bremsen erforderlich. In dieser Arbeit wird deshalb angestrebt, die elementaren Mechanismen der Reifenmechanik beim ABS-Bremsen mit theoretischen Konzepten der Gummireibung auf rauhen Oberflaechen in Verbindung zu bringen. (orig.)

  7. Development And Use Of Advanced Microfabricated Traction Force Sensing Substrates To Study The Effect of Nanosilver On Human Macrophages

    Science.gov (United States)

    Stark, Daniel Thomas

    While nanoparticles are a natural byproduct of combustion and a number of natural processes, engineered nanoparticles have only recently entered the consumer market. This motivates the development of methods for studying their effects on human cells, thereby indicating how larger models such as animals and humans might react to them. This research develops a method to mechanically characterize cellular traction forces as a measure of exposure to nanoparticles. To do this, 1microm micropillar molds were fabricated in silicon wafers using smooth sidewall reactive ion plasma etching technologies. Polydimethylsiloxane (PDMS), was cured inside the silicon molds, subsequently treated for cell culture and used to measure cellular traction forces over time in live cell time-lapse experiments. For the first time, transmitted light was used to visualize the PDMS micropillars; a force resolution of 5.6 +/-2.1nN was achieved across all experiments using a standard Olympus IX81 confocal microscope affixed with a 60x NA2.1 objective. To initiate cellular movement, monocyte chemoattractant protein (MCP-1) was conjugated to 1microm latex beads. The effects of 40nm silver nanoparticle exposures were quantified using the micropillar array. Changes in cellular behavior between the control group and cells exposed to nanosilver were not significant, although a comparison between the 5microg/ml and 10microg/ml nanosilver concentrations yielded strong significance using a 2 sided Students t test.

  8. Research on a New Bilateral Self-locking Mechanism for an Inchworm Micro In-pipe Robot with Large Traction

    Directory of Open Access Journals (Sweden)

    Junhong Yang

    2014-10-01

    Full Text Available In this paper, we present an innovative bilaterally-controllable self-locking mechanism that can be applied to the micro in-pipe robot. The background and state of the art of the inchworm micro in-pipe robot is briefly described in the very beginning of the paper, where the main factors that influence the traction ability are also discussed. Afterwards, the micro in-pipe robots’ propulsion principle based on a unidirectional self-locking mechanism is discussed. Then, several kinds of self-locking mechanisms are compared, and a new bilaterally-controllable self-locking mechanism is proposed. By implementing the self-locking mechanism, the robot's tractive force is no longer restricted by the friction force, and both two-way motion and position locking for the robot can be achieved. Finally, the traction experiment is conducted using a prototype robot with the new bilaterally-controllable self-locking mechanism. Test results show that this new self-locking mechanism can adapt itself to a diameter of >17~>20 mm and has a blocking force up to 25N, and the maximum tractive force of the in-pipe robot based on such a locking mechanism is 12N under the maximum velocity of 10mm/s.

  9. Developing traction control strategy for a plug-in hybrid electric vehicle using innovative optimization based approaches

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, L.; Gu, J.; Dong, Z. [Victoria Univ., BC (Canada). Dept. of Mechanical Engineering

    2010-07-01

    This paper described a traction control system designed for hybrid vehicles with multiple power plants and drive axles. Model-based design tools were used to develop the traction control system and plug-in hybrid vehicle models. Optimization studies were conducted in a finite number of operating states in order to maximize the electrical and mechanical energy conversion efficiency of an extended range electric vehicle. Four global optimization algorithms were then evaluated in relation to their CPU times. The studied algorithms included a genetic algorithm (GA), a particle swarm optimization (PSO) algorithm, a hybrid adaptive metamodel optimization (HAM) and space elimination and unimodal region reduction (SEUMRE) algorithm. A comparative evaluation of the algorithms demonstrated that the PSO algorithm obtained optimal results, while the HAM algorithm used significantly less computational time. Results of the optimization studies were then implemented in a controller model. Results of the study showed that the energy efficiency of the vehicle improved using the developed controller model. 4 refs., 2 tabs., 8 figs.

  10. Effect of immobilization on urine calcium excretion in orthopedic patients with pelvic fracture treated by skin traction.

    Science.gov (United States)

    Derakhshan, Ali; Derakhshan, Nima; Namazi, Hamid; Ghaffarpasand, Fariborz

    2015-03-31

    To determine the effects on urine calcium excretion of immobilization by skin traction in patients with pelvic fracture. In a prospective study, a consecutive series of patients with pelvic fracture treated by skin traction were enrolled. Serum (calcium, phosphorous, alkaline phosphatase, sodium, potassium, uric acid, BUN, creatinine) and fasting urine calcium, creatinine, sodium, potassium and uric acid were checked within 48 hours of hospitalization and at 7, 14 and 21 days of immobilization and then after 3 months of mobilization. Trends in changes of variables were recorded. Fifty five patients were enrolled in this study; they were 45 (81.8%) males and 10 (18.2%) females with a mean age 19.4 ± 12.7 years. We found that serum levels of calcium (p = 0.004), phosphorous (p = 0.047) and alkaline phosphatase (p = 0.001) increased significantly during the 3 weeks of immobilization. In the same way, urine calcium/ urine creatinine ratio increased significantly in the study period (p = 0.004). No symptomatic renal stone formation was observed during the study period. Immobilization even in short term causes hypercalciuria in orthopedic patients. Although it is transient and improves with subsequent mobilization, it is needed to be considered specifically by the team caring for this group of patients.

  11. Online Open Circuit Fault Diagnosis for Rail Transit Traction Converter Based on Object-Oriented Colored Petri Net Topology Reasoning

    Directory of Open Access Journals (Sweden)

    Lei Wang

    2016-01-01

    Full Text Available For online open circuit fault diagnosis of the traction converter in rail transit vehicles, conventional approaches depend heavily on component parameters and circuit layouts. For better universality and less parameter sensitivity during the diagnosis, this paper proposes a novel topology analysis approach to diagnose switching device open circuit failures. During the diagnosis, the topology is analyzed with fault reasoning mechanism, which is based on object-oriented Petri net (OOCPN. The OOCPN model takes in digitalized current inputs as fault signatures, and dynamical transitions between discrete switching states of a circuit with broken device are symbolized with the dynamical transitions of colored tokens in OOCPN. Such transitions simulate natural reasoning process of an expert’s brain during diagnosis. The dependence on component parameters and on circuit layouts is finally eliminated by such circuit topology reasoning process. In the last part, the proposed online reasoning and diagnosis process is exemplified with the case of a certain switching device failure in the power circuit of traction converter.

  12. Verification of electricity savings through energy-efficient train management - Energy data base for traction units - Annex 5; Verifizierung der Stromeinsparung durch energieeffizientes Zugsmanagement - Anhang 5: Energiedatenbank Traktion

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, M.; Lerjen, M.; Menth, S. [emkamatik GmbH, Wettingen (Switzerland); Luethi, M. [Swiss Federal Insitute of Technology (ETHZ), Institute for Transport Planning and Systems (IVT), Zuerich (Switzerland); Tuchschmid, M. [SBB AG, BahnUmwelt-Center, 3000 Bern (Switzerland)

    2009-11-15

    This appendix to a final report for the Swiss Federal Office of Energy (SFOE) takes a look at how various data sources on the energy consumption of the SBB's traction units can be combined into an energy-data basis. In this way, the considerable amount of work previously involved in combining and correlating data can be avoided. The aims being followed in the realisation of the traction data base are examined and discussed. The data base will provide the basis for the manual detail analysis of energy consumption within the framework of the overall efforts to save electricity using efficient train management.

  13. Phase II CRADA ORNL99-0568 Report : Developing Transmission-Less Inverter Drive Systems for Axial-Gap Permanent magnet Accessory and Traction Motors and Generators; FINAL

    International Nuclear Information System (INIS)

    McKeever, J.W.

    2001-01-01

    Researchers of the Oak Ridge National Laboratory's (ORNLs) Power Electronics and Electric Machine Research Center (PEEMRC) collaborated with Visual Computing Systems (VCS) to develop an electric axial-gap permanent magnet (PM) motor controlled by a self-sensing inverter for driving vehicle accessories such as power steering, air conditioning, and brakes. VCS designed an 8 kW motor based on their Segmented Electromagnetic Array (SEMA) technology. ORNL designed a 10 kW inverter to fit within the volume of a housing, which had been integrated with the motor. This modular design was pursued so that multiple modules could be used for higher power applications. ORNL built the first inverter under the cooperative research and development agreement (CRADA) ORNL 98-0514 and drove a refurbished Delta motor with no load during the Merit Review at ORNL on Monday, May 17, 1999. Inverter circuitry and instructions for assembling the inverters were sent to VCS. A report was prepared and delivered during the Future Car Congress in April 2000, at Arlington, Virginia. Collaboration continued under CRADA ORNL 99-0568 as VCS designed and built a SEMA motor with a dual coil platter to be the traction motor for an electric truck. VCS and ORNL assembled two 45 kW inverters. Each inverter drove one coil, which was designed to deliver 15 kW continuous power and 45 kW peak power for 90 s. The vehicle was road tested as part of the Future Truck Competition. A report was prepared and delivered during the PCIM in October 2000, at Boston, Massachusetts

  14. Study of the strategies and controls of fuel cell systems associated with traction; Etude des strategies et des structures de commande pour le pilotage des systemes energetiques a Pile a Combustible (PAC) destines a la traction

    Energy Technology Data Exchange (ETDEWEB)

    Lachaize, J.

    2004-09-15

    This work falls into project COPPACE (Contribution to the Control of Embedded Fuel cell) carried out by ALSTOM in partnership with the LEEI-INPT and the CEA and supported by the ADEME. The study deals with the modelling and the control of a Fuel Cell system (flow, pressure, temperature) and the definition of the control laws for the static inverters associated with the traction of power train. We develop then a strategy of management of energy by taking into account the criteria of the hydrogen consumption or energy stored in the ultracaps. Each step is verified by total simulation according to a specific profile of mission and a precise model of fuel cells which has been simplified to reduce the computing time. The control of this system is defined by a separate treatment of the components, to finalize the total function objective. The results of simulations show that the system can follow the requested power while controlling the critical elements. (author)

  15. Effects of Adding Segmental Traction Therapy to Routine Physiotherapy on Pain and Functional Ability of Patients with Acute Low Back Pain

    Directory of Open Access Journals (Sweden)

    Parvin Akberov

    2015-06-01

    Full Text Available Background: Low back pain (LBP is one of the most common musculoskeletal complications of today’s societies which, poses a big portion of health expenses and work absentees. Lumbar disc herniation is claimed to be one of the several causes of LBP. Conservative therapies like physiotherapy are found to be beneficial for treatment in such a kind of LBP. However, there is low evidence proving traction therapy can be effective. Therefore, the aim of this study was to evaluate effects of a 7-day physiotherapy protocol along with segmental traction therapy on pain and range of motion in patients with acute LBP Methods: A total of 9 patients with acute LBP voluntarily participated in this study. They undertook a 7-day conventional physiotherapy along with segmental traction therapy. Pain, functional ability and lumbar flexion range of motion (ROM were measured before and after the therapeutic intervention. Results: A significant reduction in pain was observed after the intervention (P=0.006. In addition, patients’ functional ability increased significantly (P=0.03.However, there were no significant changes in lumbar in flexion ROM. Conclusion: According to results of the present study segmental traction therapy along with a physiotherapy protocol consisting of TENS, Ultrasound and Hot pack reduces pain and improves functional ability in patient with acute LBP. Although no effect on lumbar ROM is expected.

  16. Effects of segmental traction therapy on lumbar disc herniation in patients with acute low back pain measured by magnetic resonance imaging: A single arm clinical trial.

    Science.gov (United States)

    Karimi, Noureddin; Akbarov, Parvin; Rahnama, Leila

    2017-01-01

    Low Back Pain (LBP) is considered as one of the most frequent disorders, which about 80% of adults experience in their lives. Lumbar disc herniation (LDH) is a cause for acute LBP. Among conservative treatments, traction is frequently used by clinicians to manage LBP resulting from LDH. However, there is still a lack of consensus about its efficacy. The purpose of this study was to evaluate the effects of segmental traction therapy on lumbar discs herniation, pain, lumbar range of motion (ROM), and back extensor muscles endurance in patients with acute LBP induced by LDH. Fifteen patients with acute LBP diagnosed by LDH participated in the present study. Participants undertook 15 sessions of segmental traction therapy along with conventional physiotherapy, 5 times a week for 3 weeks. Lumbar herniated mass size was measured before and after the treatment protocol using magnetic resonance imaging. Furthermore, pain, lumbar ROM and back muscle endurance were evaluated before and after the procedure using clinical outcome measures. Following the treatment protocol, herniated mass size and patients' pain were reduced significantly. In addition, lumbar flexion ROM showed a significant improvement. However, no significant change was observed for back extensor muscle endurance after the treatment procedure. The result of the present study showed segmental traction therapy might play an important role in the treatment of acute LBP stimulated by LDH.

  17. Safety and efficacy of endoscopic submucosal dissection using IT knife nano with clip traction method for early esophageal squamous cell carcinoma.

    Science.gov (United States)

    Kitagawa, Yoshiyasu; Suzuki, Takuto; Hara, Taro; Yamaguchi, Taketo

    2018-01-01

    Although endoscopic submucosal dissection (ESD) is an accepted and established treatment for early esophageal squamous cell carcinoma (EESCC), it is technically difficult, time consuming, and less safe than endoscopic mucosal resection. To perform ESD safely and more efficiently, we proposed a new technique of esophageal ESD using an IT knife nano with the clip traction method. This study aimed to evaluate the efficacy and safety of ESD using this new technique. We retrospectively reviewed all consecutive cases of esophageal ESD performed using an IT knife nano with the clip traction method at our hospital between March 2013 and January 2017. Therapeutic efficacy and safety were also assessed. A total of 103 patients underwent esophageal ESD using the IT knife nano with the clip traction method. In all cases, we performed en bloc resection. Complete resection was achieved in 100 cases (97.1%). The median operating time was 40 (range 13-230) min. No cases of perforation or delayed bleeding occurred. Although two cases (2.0%) of mediastinal emphysema occurred without visible perforation at endoscopy, all were successfully managed conservatively. The new technique of esophageal ESD using the IT knife nano with the clip traction method appears to be feasible, effective, and safe for EESCC treatment.

  18. MATHEMATICAL MODELING OF TRANSIENT EMERGENCY ELECTROMAGNETIC PROCESSES IN THE SYSTEM OF THE ELECTROMAGNETIC TRACTION DC. 2. SHORT CIRCUIT WITH ELECTRIC ROLLING STOCK

    Directory of Open Access Journals (Sweden)

    P. E. Mihalichenko

    2010-04-01

    Full Text Available The article deals with the description of mathematical model of the system of traction electric power supply with load in the short circuit condition as well as the calculation results of this emergency process. The transition values as well as the character of their change, which can be used for detection of emergency processes, have been determined.

  19. Development of theory of spectra and its adaptation to the tasks of analysis of transient emergency regimes for electric traction systems

    Directory of Open Access Journals (Sweden)

    P.Ye. Mikhalichenko

    2012-04-01

    Full Text Available In the article the notion of current and instantaneous spectrum is introduced for the analysis of the deterministic functions of electric values of the system of DC electric traction supply in the case of its emergency operation regimes.

  20. STRUCTURAL ANALYSIS OF RAILWAYS BOLSTER-BEAM UNDER COMMERCIAL OPERATION CONDITIONS: OVER-TRACTION AND OVER-BRAKING

    Directory of Open Access Journals (Sweden)

    Ronald M. MARTINOD

    2016-06-01

    Full Text Available The conditions for the operation of railway systems are closely related to the increase of the commercial demand; as a consequence, the performance of the structural elements of railways changes. The present paper focuses on a study of the structural behaviour of bolster-beams under commercial operation conditions of railway systems, specifically in the dynamic conditions generated in events of over-traction and over-braking on the vehicle running. The proposed work is constructed based on the following phases: (i analysis of the kinematics of the vehicle; (ii development of numerical models, a model based on the multibody theory, and a Finite Elements model; (iii development of experimental field tests; and (iv development of simulations for a detailed analysis of the structural behaviour for a study of the strain distribution in the main bolster-beam. This study is applied to a particular case of a railway system that provides commercial service to passengers.

  1. Performance and economic analysis of a plug and play regenerative brake for improving energy efficiency for traction elevators

    Science.gov (United States)

    Jeraputra, Chuttchaval; Tiptipakorn, Supun

    2017-05-01

    This paper presents performance and economic analysis of a plug and play regenerative brake for improving energy efficiency for traction elevators. The proposed regenerative brake recycles the energy loss of a dynamic brake and feeds into the grid while an elevator inverter is operating in the braking mode. According to field measurement of energy consumption, it reveals that the efficiency can be improved as much as 18%. The prototype of a regenerative brake 12 kW, 400V, 3ϕ is developed and tested on an elevator simulator. It is shown that it can transfer energy out of a DC capacitor before the dynamic brake kicks in. Further, an economic analysis is provided to carry out the payback period and the present worth equivalent to confirm economic feasibility.

  2. Study of traction rolling-stock using in Lithuanian sector of railway line “Rail Baltica”

    Directory of Open Access Journals (Sweden)

    Gintautas BUREIKA

    2012-01-01

    Full Text Available The article analyses the current traction rolling-stock used by „Lietuvos geležinkeliai“ Plc. for freight transportation. The technical data of the above mentioned rolling-stock is explored and compared, and operation costs are estimated in the article. After the assessment of the forecasts of freight flows on the constructed railway „Rail Baltica“, the algorithm for selection of freight locomotives was proposed. The efficiency of the locomotives operated on the railway is determined by three multicriteria evaluation methods: the sum of ratings, simple additive weighting, and the geometric mean method. Locomotives are valued in accordance with technical, economic and ecological parameters. The results of possible effective performance of the rolling stock have been determined by changing coefficient values of the criteria. Finally, basic conclusions are given.

  3. Acute quadriplegia following closed traction reduction of a cervical facet dislocation in the setting of ossification of the posterior longitudinal ligament: case report.

    Science.gov (United States)

    Wimberley, David W; Vaccaro, Alexander R; Goyal, Nitin; Harrop, James S; Anderson, D Greg; Albert, Todd J; Hilibrand, Alan S

    2005-08-01

    A case report of acute quadriplegia resulting from closed traction reduction of traumatic bilateral cervical facet dislocation in a 54-year-old male with concomitant ossification of the posterior longitudinal ligament (OPLL). To report an unusual presentation of a spinal cord injury, examine the approach to reversal of the injury, and review the treatment and management controversies of acute cervical facet dislocations in specific patient subgroups. The treatment of acute cervical facet dislocations is an area of ongoing controversy, especially regarding the question of the necessity of advanced imaging studies before closed traction reduction of the dislocated cervical spine. The safety of an immediate closed, traction reduction of the cervical spine in awake, alert, cooperative, and appropriately select patients has been reported in several studies. To date, there have been no permanent neurologic deficits resulting from awake, closed reduction reported in the literature. A case of temporary, acute quadriplegia with complete neurologic recovery following successful closed traction reduction of a bilateral cervical facet dislocation in the setting of OPLL is presented. The clinical neurologic examination, radiographic, and advanced imaging studies before and after closed, traction reduction of a cervical facet dislocation are evaluated and discussed. A review of the literature regarding the treatment of acute cervical facet dislocations is presented. Radiographs showed approximately 50% subluxation of the fifth on the sixth cervical vertebrae, along with computerized tomography revealing extensive discontinuous OPLL. The cervical facet dislocation was successfully reduced with an awake, closed traction reduction, before magnetic resonance imaging (MRI) evaluation. The patient subsequently had acute quadriplegia develop, with the ensuing MRI study illustrating severe spinal stenosis at the C5, C6 level as a result of OPLL or a large extruded disc herniation

  4. heväärtusliku vallasasja süstemaatiline vargus KarS § 199 lõike 2 punkti 9 tähenduses. Tartu Ringkonnakohtu kriminaalkolleegiumi määrus kriminaalasjas 1-11-11324 (Riigikohtu kriminaalkolleegiumi otsuses asjas 3-1-1-87-07 väljendatud seisu

    Index Scriptorium Estoniae

    Randma, Paavo, 1977-

    2013-01-01

    Riigikohus leidis lahendis 3-1-1-87-07, et süstemaatilisuse jaatamiseks on vaja isiku poolt vähemalt kolme varguse toimepanemist. Ringkonnakohus asus lahendis 1-11-11324 seisukohale, et varguste toimepanemisest kui inimese elustiilist saab väheväärtuslike vallasasjade varastamise korral rääkida vaid juhul, kui need pannakse toime teatud kindla ajavahemiku vältel

  5. Application of several plasticity models to the analysis of a tube subjected to traction and combined torsion

    International Nuclear Information System (INIS)

    Caumette, Pierre; Cheissoux, J.L.

    1982-01-01

    The progressive deformation of a thin-walled steel tube is analysed when the tube is submitted to cyclic torsion under constant loading. Isotopic and kinematic hardening models are applied, assuming a bilinear stress-strain law (constant hardening modulus) [fr

  6. ESTABLISHING SUSTAINABLE US HEV/PHEV MANUFACTURING BASE: STABILIZED LITHIUM METAL POWDER, ENABLING MATERIAL AND REVOLUTIONARY TECHNOLOGY FOR HIGH ENERGY LI-ION BATTERIES

    Energy Technology Data Exchange (ETDEWEB)

    Yakovleva, Marina

    2012-12-31

    FMC Lithium Division has successfully completed the project “Establishing Sustainable US PHEV/EV Manufacturing Base: Stabilized Lithium Metal Powder, Enabling Material and Revolutionary Technology for High Energy Li-ion Batteries”. The project included design, acquisition and process development for the production scale units to 1) produce stabilized lithium dispersions in oil medium, 2) to produce dry stabilized lithium metal powders, 3) to evaluate, design and acquire pilot-scale unit for alternative production technology to further decrease the cost, and 4) to demonstrate concepts for integrating SLMP technology into the Li- ion batteries to increase energy density. It is very difficult to satisfy safety, cost and performance requirements for the PHEV and EV applications. As the initial step in SLMP Technology introduction, industry can use commercially available LiMn2O4 or LiFePO4, for example, that are the only proven safer and cheaper lithium providing cathodes available on the market. Unfortunately, these cathodes alone are inferior to the energy density of the conventional LiCoO2 cathode and, even when paired with the advanced anode materials, such as silicon composite material, the resulting cell will still not meet the energy density requirements. We have demonstrated, however, if SLMP Technology is used to compensate for the irreversible capacity in the anode, the efficiency of the cathode utilization will be improved and the cost of the cell, based on the materials, will decrease.

  7. Construction of hevein (Hev b 6.02) with reduced allergenicity for immunotherapy of latex allergy by comutation of six amino acid residues on the conformational IgE epitopes.

    Science.gov (United States)

    Karisola, Piia; Mikkola, Jari; Kalkkinen, Nisse; Airenne, Kari J; Laitinen, Olli H; Repo, Susanna; Pentikäinen, Olli T; Reunala, Timo; Turjanmaa, Kristiina; Johnson, Mark S; Palosuo, Timo; Kulomaa, Markku S; Alenius, Harri

    2004-02-15

    Recently we have established that IgE Abs bind to conformational epitopes in the N- and C-terminal regions of the major natural rubber latex allergen, hevein (Hev b 6.02). To identify the critical amino acid residues that interact with IgE, the hevein sequence was scanned by using site-specific mutations. Twenty-nine hevein mutants were designed and produced by a baculovirus expression system in insect cells and tested by IgE inhibition-ELISA using sera from 26 latex allergic patients. Six potential IgE-interacting residues of hevein (Arg(5), Lys(10), Glu(29), Tyr(30), His(35), and Gln(38)) were identified and characterized further in detail. Based on these six residues, two triple mutants (Hdelta3A, Hdelta3B) and hevein mutant where all six residues were mutated (Hdelta6), were designed, modeled, and produced. Structural and functional properties of these combinatory mutants were compared experimentally and in silico with those of recombinant hevein. The IgE-binding affinity of the mutants decreased by three to five orders of magnitude as compared with that of recombinant hevein. Skin prick test reactivity of the triple mutant HDelta3A was drastically reduced and that of the six-residue mutant Hdelta6 was completely abolished in all patients examined in this study. The approach presented in this paper offers tools for identification and modification of amino acid residues on conformational epitopes of allergens that interact with IgE. Hevein with a highly reduced ability to bind IgE should provide a valuable candidate molecule for immunotherapy of latex allergy and is anticipated to have a low risk of systemic side effects.

  8. Crystallization and Identification of the Glycosylated Moieties of Two Isoforms of the Main Allergen Hev b 2 and Preliminary X-ray Analysis of Two Polymorphs of Isoform ll

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes-Silva,D.; Mendoza-Hernandez, G.; Stojanoff, V.; Palomares, L.; Zenteno, E.; Torres-Larios, A.; Rodriguez-Romero, A.

    2007-01-01

    Latex from Hevea brasiliensis contains several allergenic proteins that are involved in type I allergy. One of them is Hev b 2, which is a {beta}-1,3-glucanase enzyme that exists in different isoforms with variable glycosylation content. Two glucanase isoforms were isolated from trees of the GV-42 clone by gel filtration, affinity and ion-exchange chromatography. Isoform I had a carbohydrate content of about 20%, with N-linked N-acetyl-glucosamine, N-acetyl-galactosamine, fucose and galactose residues as the main sugars, while isoform II showed 6% carbohydrate content consisting of N-acetyl-glucosamine, fucose, mannose and xylose. Both isoforms were crystallized by the hanging-drop vapor-diffusion method. Isoform I crystals were grown using 0.2 M trisodium citrate dihydrate, 0.1 M Na HEPES pH 7.5 and 20%(v/v) 2-propanol, but these crystals were not appropriate for data collection. Isoform II crystals were obtained under two conditions and X-ray diffraction data were collected from both. In the first condition (0.2 M trisodium citrate, 0.1 M sodium cacodylate pH 6.5, 30% 2-propanol), crystals belonging to the tetragonal space group P4{sub 1} with unit-cell parameters a = b = 150.17, c = 77.41 {angstrom} were obtained. In the second condition [0.2 M ammonium acetate, 0.1 M trisodium citrate dihydrate pH 5.6, 30%(w/v) polyethylene glycol 4000] the isoform II crystals belonged to the monoclinic space group P2{sub 1}, with unit-cell parameters a = 85.08, b = 89.67, c = 101.80 {angstrom}, {beta}= 113.6{sup o}. Preliminary analysis suggests that there are four molecules of isoform II in both asymmetric units.

  9. Crystallization and identification of the glycosylated moieties of two isoforms of the main allergen Hev b 2 and preliminary X-ray analysis of two polymorphs of isoform II

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes-Silva, D. [Instituto de Química, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico); Mendoza-Hernández, G. [Facultad de Medicina, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico); Stojanoff, V. [Brookhaven National Laboratory, National Synchrotron Light Source, Upton, NY (United States); Palomares, L. A. [Instituto de Biotecnología, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico); Zenteno, E. [Facultad de Medicina, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico); Torres-Larios, A. [Instituto de Fisiología Celular, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico); Rodríguez-Romero, A., E-mail: adela@servidor.unam.mx [Instituto de Química, Universidad Nacional Autónoma de México, Circuito Exterior s/n, Cuidad Universitaria, Coyoacán, México, DF 04510 (Mexico)

    2007-09-01

    Crystallization of important glycoenzymes involved in IgE-mediated latex allergy. Latex from Hevea brasiliensis contains several allergenic proteins that are involved in type I allergy. One of them is Hev b 2, which is a β-1,3-glucanase enzyme that exists in different isoforms with variable glycosylation content. Two glucanase isoforms were isolated from trees of the GV-42 clone by gel filtration, affinity and ion-exchange chromatography. Isoform I had a carbohydrate content of about 20%, with N-linked N-acetyl-glucosamine, N-acetyl-galactosamine, fucose and galactose residues as the main sugars, while isoform II showed 6% carbohydrate content constisting of N-acetyl-glucosamine, fucose, mannose and xylose. Both isoforms were crystallized by the hanging-drop vapour-diffusion method. Isoform I crystals were grown using 0.2 M trisodium citrate dihydrate, 0.1 M Na HEPES pH 7.5 and 20%(v/v) 2-propanol, but these crystals were not appropriate for data collection. Isoform II crystals were obtained under two conditions and X-ray diffraction data were collected from both. In the first condition (0.2 M trisodium citrate, 0.1 M sodium cacodylate pH 6.5, 30% 2-propanol), crystals belonging to the tetragonal space group P4{sub 1} with unit-cell parameters a = b = 150.17, c = 77.41 Å were obtained. In the second condition [0.2 M ammonium acetate, 0.1 M trisodium citrate dihydrate pH 5.6, 30%(w/v) polyethylene glycol 4000] the isoform II crystals belonged to the monoclinic space group P2{sub 1}, with unit-cell parameters a = 85.08, b = 89.67, c = 101.80 Å, β = 113.6°. Preliminary analysis suggests that there are four molecules of isoform II in both asymmetric units.

  10. Crystallization and identification of the glycosylated moieties of two isoforms of the main allergen Hev b 2 and preliminary X-ray analysis of two polymorphs of isoform II

    International Nuclear Information System (INIS)

    Fuentes-Silva, D.; Mendoza-Hernández, G.; Stojanoff, V.; Palomares, L. A.; Zenteno, E.; Torres-Larios, A.; Rodríguez-Romero, A.

    2007-01-01

    Crystallization of important glycoenzymes involved in IgE-mediated latex allergy. Latex from Hevea brasiliensis contains several allergenic proteins that are involved in type I allergy. One of them is Hev b 2, which is a β-1,3-glucanase enzyme that exists in different isoforms with variable glycosylation content. Two glucanase isoforms were isolated from trees of the GV-42 clone by gel filtration, affinity and ion-exchange chromatography. Isoform I had a carbohydrate content of about 20%, with N-linked N-acetyl-glucosamine, N-acetyl-galactosamine, fucose and galactose residues as the main sugars, while isoform II showed 6% carbohydrate content constisting of N-acetyl-glucosamine, fucose, mannose and xylose. Both isoforms were crystallized by the hanging-drop vapour-diffusion method. Isoform I crystals were grown using 0.2 M trisodium citrate dihydrate, 0.1 M Na HEPES pH 7.5 and 20%(v/v) 2-propanol, but these crystals were not appropriate for data collection. Isoform II crystals were obtained under two conditions and X-ray diffraction data were collected from both. In the first condition (0.2 M trisodium citrate, 0.1 M sodium cacodylate pH 6.5, 30% 2-propanol), crystals belonging to the tetragonal space group P4 1 with unit-cell parameters a = b = 150.17, c = 77.41 Å were obtained. In the second condition [0.2 M ammonium acetate, 0.1 M trisodium citrate dihydrate pH 5.6, 30%(w/v) polyethylene glycol 4000] the isoform II crystals belonged to the monoclinic space group P2 1 , with unit-cell parameters a = 85.08, b = 89.67, c = 101.80 Å, β = 113.6°. Preliminary analysis suggests that there are four molecules of isoform II in both asymmetric units

  11. Active management of the third stage of labour without controlled cord traction: a randomized non-inferiority controlled trial

    Directory of Open Access Journals (Sweden)

    Derman Richard

    2009-01-01

    Full Text Available Abstract Background The third stage of labour refers to the period between birth of the baby and complete expulsion of the placenta. Some degree of blood loss occurs after the birth of the baby due to separation of the placenta. This period is a risky period because uterus may not contract well after birth and heavy blood loss can endanger the life of the mother. Active management of the third stage of labour (AMTSL reduces the occurrence of severe postpartum haemorrhage by approximately 60–70%. Active management consists of several interventions packaged together and the relative contribution of each of the components is unknown. Controlled cord traction is one of those components that require training in manual skill for it to be performed appropriately. If it is possible to dispense with controlled cord traction without losing efficacy it would have major implications for effective management of the third stage of labour at peripheral levels of health care. Objective The primary objective is to determine whether the simplified package of oxytocin 10 IU IM/IV is not less effective than the full AMTSL package. Methods A hospital-based, multicentre, individually randomized controlled trial is proposed. The hypothesis tested will be a non-inferiority hypothesis. The aim will be to determine whether the simplified package without CCT, with the advantage of not requiring training to acquire the manual skill to perform this task, is not less effective than the full AMTSL package with regard to reducing blood loss in the third stage of labour. The simplified package will include uterotonic (oxytocin 10 IU IM injection after delivery of the baby and cord clamping and cutting at approximately 3 minutes after birth. The full package will include the uterotonic injection (oxytocin 10 IU IM, controlled cord traction following observation of uterine contraction and cord clamping and cutting at approximately 3 minutes after birth. The primary outcome

  12. Seroprevalence for hepatitis E virus (HEV infection among volunteer blood donors of the Regional Blood Bank of Londrina, State of Paraná , Brazil Soroprevalência da infecção pelo virus da hepatite E (VHE em candidatos a doadores de sangue voluntários do Hemocentro Regional de Londrina, Londrina, Estado do Paraná, Brasil

    Directory of Open Access Journals (Sweden)

    André Luiz Bortoliero

    2006-04-01

    Full Text Available A cross-sectional study was carried out among 996 volunteer blood donors enrolled from May 1999 to December 1999 to determine the seroprevalence of hepatitis E virus (HEV infection among volunteer blood donors of the Regional Blood Bank of Londrina, State of Paraná, Brazil, and to evaluate whether the rate of seroprevalence of IgG anti-HEV antibodies is associated with sociodemographic variables and with seropositivity for hepatitis A virus (HAV infection. All participants answered the questionnaire regarding the sociodemographic characterisitcs. Serum samples were tested for IgG antibodies to HEV (anti-HEV by an enzyme linked immunoassay (ELISA. All serum samples positive for anti-HEV IgG and 237 serum samples negative for anti-HEV were also assayed for IgG anti-HAV antibodies by ELISA. Anti-HEV IgG was confirmed in 23/996 samples, resulting in a seroprevalence of 2.3% for HEV infection, similar to previous results obtained in developed countries. No significant association was found between the presence of anti-HEV IgG antibodies and the sociodemographic variables including gender, age, educational level, rural or urban areas, source of water, and sewer system (p > 0.05. Also, no association with seropositivity for anti-HAV IgG antibodies was observed (p > 0.05. Although this study revealed a low seroprevalence of HEV infection in the population evaluated, the results showed that this virus is circulating among the population from Londrina, South Brazil, and point out the need of further studies to define the clinical and epidemiological importance of HEV infection and to identify additional risk factors involved in the epidemiology and pathogenesis of this infection in this population.Os objetivos do estudo foram determinar a soroprevalência da infecção pelo vírus da hepatite E (VHE em candidatos a doadores de sangue voluntários do Hemocentro Regional de Londrina, Paraná, e avaliar se essa soroprevalência está associada com vari

  13. Comparison of 48V rare-earth-free reluctance traction motor drives for mild hybrid powertrain

    NARCIS (Netherlands)

    Bao, J.; Boynov, K.; Paulides, J.J.H.; Wijnands, C.G.E. (Korneel); Lomonova, E.

    2016-01-01

    This paper provides a comparative analysis of three types of electrical drives with rare-earth- free reluctance motors for next-generation 48V mild hybrid automotive applications. The drives with switched reluctance motors (SRM), variable flux reluctance motors (VFRM) and synchronous reluctance

  14. Assessment of potential energy efficiency improvements in the traction sector of the Swiss Federal Railways; Potentialermittlung Energieeffizienz Traktion bei den SBB - Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, M.; Menth, S.; Lerjen, M.

    2007-07-01

    Possibilities to reduce the consumption of 16.7-Hz traction energy of Swiss Federal Railways (SBB) have been investigated. Various proposals have been discussed together with experts of SBB's Passenger, Cargo and Infrastructure divisions. Based on numerical simulations for representative train runs, the total consumption of the SBB network could be calculated and compared with real values. The possible reduction e.g. by energy optimised driving could be derived from this comparison; it is between 3 and 5 % of the specific consumption both for the influence by train driver and by traffic control. Technical measures in traction units and passenger coaches lead to reductions of up to about 3%, depending on the vehicle type. It is important that all measures take into account the extremely dense traffic on SBB's network and do not reduce the attractiveness for the customers. (author)

  15. Energy control centres and traction power management of the OeBB infrastructure; Energieleitstellen und Traktionsstrommanagement der OeBB-Infrastruktur

    Energy Technology Data Exchange (ETDEWEB)

    Gammer, Michael; Heinze, Florian [OeBB-Infrastruktur AG, Vienna (Austria). Geschaeftsbereich Energie

    2013-04-15

    According to the OeBB control centre concept, the currently four operations management sites for the 15 kV railway power network will be reduced to just two locations which will be reoriented to operate as energy control centres. For the support of the operators, tools have been developed under the title traction power management, which are based on combined simulations of overhead line network and train operations. (orig.)

  16. Improving the electromagnetic compatibility of track circuits with electric rolling stock of double power supply with induction traction motors and electrictraction network

    Directory of Open Access Journals (Sweden)

    N.G. Visin

    2012-04-01

    Full Text Available In this article the research results of many authors on the effect of current interference from the existing electric rolling stock with induction traction motors (ITM on the track circuits and the possibility of exceeding the train traffic safety standards are used. The new promising scheme of power circuit for electric locomotive of double power supply with an ITM applying the intermediary high-frequency transformer for reducing significantly the interference effects to SCB and communication devices is developed.

  17. Thermal modeling of secondary lithium batteries for electric vehicle/hybrid electric vehicle applications

    Science.gov (United States)

    Al-Hallaj, Said; Selman, J. R.

    A major obstacle to the development of commercially successful electric vehicles (EV) or hybrid electric vehicles (HEV) is the lack of a suitably sized battery. Lithium ion batteries are viewed as the solution if only they could be "scaled-up safely", i.e. if thermal management problems could be overcome so the batteries could be designed and manufactured in much larger sizes than the commercially available near-2-Ah cells. Here, we review a novel thermal management system using phase-change material (PCM). A prototype of this PCM-based system is presently being manufactured. A PCM-based system has never been tested before with lithium-ion (Li-ion) batteries and battery packs, although its mode of operation is exceptionally well suited for the cell chemistry of the most common commercially available Li-ion batteries. The thermal management system described here is intended specifically for EV/HEV applications. It has a high potential for providing effective thermal management without introducing moving components. Thereby, the performance of EV/HEV batteries may be improved without complicating the system design and incurring major additional cost, as is the case with "active" cooling systems requiring air or liquid circulation.

  18. Rational Formations of a Metro Train Improve Its Efficiencies of Both Traction Energy Utilization and Passenger Transport

    Directory of Open Access Journals (Sweden)

    Xuesong Feng

    2013-01-01

    Full Text Available Based on simulations of passenger transports of two representative types of metro trains in China, this study analyzes efficiencies of energy consumption and passenger transport of a metro train in the effect of its target speed, formation scale (FS (i.e., length and mass of the formation, relative traction capacity (RTC (i.e., ratio of the motoring cars to all its cars, and so forth. It is found that increasing energy cost efficiency of a metro train with decreasing its target speed is evidently accelerated with reducing its RTC below 0.50 at the expense of obviously lowering its passenger transport efficiency. Moreover, if the passenger capacity of the train is sufficiently utilized, increasing its FS for the same RTC is easy to have its passenger transport efficiency improved significantly even for a meanwhile much decreased target speed with consuming energy less intensively. Therefore, metro trains in peak hours may take comparatively big FSs, relatively high target speeds, and RTCs over 0.50 to meet usually urgent and large-scale travel demands in such time. In contrast, trains in nonpeak hours ought to have small FSs, relatively low target speeds, and RTCs smaller than 0.50 for mainly avoiding energy waste.

  19. Root length and alveolar bone level of impacted canines and adjacent teeth after orthodontic traction: a long-term evaluation

    Science.gov (United States)

    da SILVA, Aldir Cordeiro; CAPISTRANO, Anderson; de ALMEIDA-PEDRIN, Renata Rodrigues; CARDOSO, Maurício de Almeida; CONTI, Ana Cláudia de Castro Ferreira; CAPELOZZA, Leopoldino

    2017-01-01

    Abstract Objective The aim of this retrospective study was to evaluate the long-term effects of orthodontic traction on root length and alveolar bone level in impacted canines and adjacent teeth. Material and Methods Sample consisted of 16 patients (nine males and seven females), mean initial age 11 years and 8 months presenting with unilaterally maxillary impacted canines, palatally displaced, treated with the same surgical and orthodontic approach. Teeth from the impacted-canine side were assigned as Group I (GI), and contralateral teeth as control, Group II (GII). The mean age of patients at the end of orthodontic treatment was 14 years and 2 months and the mean post-treatment time was 5 years and 11 months. Both contralateral erupted maxillary canines and adjacent teeth served as control. Root length and alveolar bone level (buccal and palatal) were evaluated on cone-beam computed tomography (CBCT) images. The comparison of root length and alveolar bone level changes between groups were assessed by applying paired t-test, at a significance level of 5% (p<0.05). Results There were no statistically significant differences in root length and buccal and palatal bone levels of canines and adjacent teeth among groups. Conclusions Impacted canine treatment by closed-eruption technique associated with canine crown perforation, has a minimal effect on root length and buccal and palatal alveolar bone level in both canine and adjacent teeth, demonstrating that this treatment protocol has a good long-term prognosis. PMID:28198979

  20. Practical implementation of the concept of converted electric vehicle with advanced traction and dynamic performance and environmental safety indicators

    Science.gov (United States)

    Sidorov, K. M.; Yutt, V. E.; Grishchenko, A. G.; Golubchik, T. V.

    2018-02-01

    The objective of the work presented in this paper is to describe the implementation of the technical solutions have been developed, with regard to structure, composition, and characteristics, for an experimental prototype of an electric vehicle which has been converted from a conventional vehicle. The methodology of the study results is based on the practical implementation of the developed concept of the conversion of conventional vehicles into electric vehicles. The main components of electric propulsion system of the experimental prototype of electric vehicle are developed and manufactured on the basis of computational researches, taking into account the criteria and principles of conversion within the framework of presented work. The article describes a schematic and a design of power conversion and commutation electrical equipment, traction battery, electromechanical transmission. These results can serve as guidance material in the design and implementation of electric propulsion system (EPS) components of electric vehicles, facilitate the development of optimal technical solutions in the development and manufacture of vehicles, including those aimed at autonomy of operation and the use of perspective driver assistance systems. As part of this work, was suggested a rational structure for an electric vehicle experimental prototype, including technical performance characteristics of the components of EPS.

  1. Effect of joint traction on functional improvement and quality of life in patients with severe knee osteoarthritis

    Directory of Open Access Journals (Sweden)

    Sedigheh Sadat Naeimee

    2012-07-01

    Full Text Available Background and aim: Osteoarthritis (OA is the most prevalent joint disease in adults around the world and its incidence rises with age. Patients with severe knee osteoarthritis often complain of pain and severe functional disability. Most of conservative treatments used in this group of patients induce poor improvements. This study evaluated the effect of joint traction on quality of life of patients with severe knee osteoarthritis.Materials and Methods: In this clinical trial study, forty female patients with severe knee OA were randomly assigned to two following groups; common physiotherapy treatment and common physiotherapy treatment accompanied by knee distraction. Quality of life was evaluated pre- and post-treatment and also one month follow-up using the Knee injury and Osteoarthritis Outcome Score (KOOS questionnaire.Results: Common physiotherapy treatment accompanied by knee distraction resulted in significantly better quality of life post-treatment and at 1month follow-up, compared to common physiotherapy treatment alone (P<0.01.Conclusion: Common physiotherapy treatment accompanied by knee distraction induces significant improvement in quality of life in patients with severe knee osteoarthritis compared to common physiotherapy treatment alone.

  2. Oesophageal elongation with traction sutures (FOKER procedure in a newborn baby with long-gap oesophageal atresia (LGEA: Maybe too early, maybe too dangerous?

    Directory of Open Access Journals (Sweden)

    Holger Till

    2013-01-01

    Full Text Available In children with long gap oesophageal atresia (LGEA, the FOKER technique (oesophageal elongation with traction sutures has been criticized for its high complication rate. We advocate analysing such problems to increase the safety in the future. The present case report will focus on timing. A female newborn (3000 g with LGEA (gap of 5 cm was delivered in an outward hospital. On day two of life, she received traction sutures on both pouches. By day five, all sutures had torn out, and a primary anastomosis was attempted. However, it leaked severely. Thus, on day ten, the oesophagus was approached from the neck converting the proximal end into a spit fistula and closing the distal end blindly. Furthermore, the gastro-oesophageal (GE- junction was wrapped with a Teflon sling. When the baby arrived in our institution, she suffered from cavernous oesophageal masses extending from the thoracic inlet down to the diaphragm and fistulas draining them into the neck as well as into the right lung. Moreover, the Teflon sling had dislodged allowing for GE-reflux. In several stages, the oesophageal remnants were resected without any complications. Finally, Prof. Alaa Hamza performed a colonic interposition, which is working well today. In conclusion, the present case aims to caution paediatric surgeons to apply traction sutures for oesophageal elongation in newborns with LGEA.

  3. Outcomes of microscope-integrated intraoperative optical coherence tomography-guided center-sparing internal limiting membrane peeling for myopic traction maculopathy: a novel technique.

    Science.gov (United States)

    Kumar, Atul; Ravani, Raghav; Mehta, Aditi; Simakurthy, Sriram; Dhull, Chirakshi

    2017-07-04

    To evaluate the outcomes of pars plana vitrectomy (PPV) with microscope-integrated intraoperative optical coherence tomography (I-OCT)-guided traction removal and center-sparing internal limiting membrane (cs-ILM) peeling. Nine eyes with myopic traction maculopathy as diagnosed on SD-OCT underwent PPV with I-OCT-guided cs-ILM peeling and were evaluated prospectively for resolution of central macular thickness (CMT) and improvement in best-corrected visual acuity (BCVA), and complications, if any, were noted. All patients were followed up for more than 9 months. Resolution of the macular retinoschisis was seen in all nine eyes on SD-OCT. At 36 weeks, there was a significant improvement in mean BCVA from the preoperative BCVA (P = 0.0089) along with a reduction in the CMT from 569.77 ± 263.19 to 166.0 ± 43.91 um (P = 0.0039). None of the eyes showed worsening of BCVA or development of full-thickness macular hole in the intraoperative or follow-up period. PPV with I-OCT-guided cs-ILM peeling helps in complete removal of traction, resolution of retinoschisis and good functional recovery with low intraoperative and postoperative complications.

  4. Analysis of mechanical traction in biofilms chitosan and clay aiming fruits coating

    Directory of Open Access Journals (Sweden)

    Suliene Dantas do Nascimento

    2014-12-01

    Full Text Available A new concept of food packaging has been studied and developed in order to meet the application needs of the market. The application of such biofilms coating is directly related to its characteristics and possible interactions of these with the product and the environment. There is evidence that chitosan is a viable alternative to be applied in the coating for fruit characteristics antifungal, antibacterial and its direct action as a barrier to water vapor, which is the latest aging fruit. The clay, besides increasing permeability to water vapor, enables a greater adhesion of the film on the fruit surface. This paper presents the results that were obtained from the development of chitosan films aimed at applying the coating of fruit. It were made tensile test with films using different chitosan and clay concentrations. The tests followed the standards of ASTM D882/02. The best results were obtained for the coating of chitosan in 2% acetic acid, which showed a plastic strain of 4.4% and a maximum stress at rupture of 50.2 MPa. The results were lower for the films with the addition of clay; the best result was observed for this coating with chitosan to 2% clay plus 2% acetic acid, with plastic deformation of 2.9% and maximum stress at rupture 18.9 MPa.

  5. Overview of battery technology for HEV

    NARCIS (Netherlands)

    Smets, S.; Debal, P.; Conte, V.; Alaküla, M.; Santini, D.; Duvall, M.; Winkel, R.; Badin, F.

    2006-01-01

    Several electric energy storage systems exist with different principles and characteristics. On the other hand, there are also various hybrid electric vehicles with specific requirements. This paper gives an overview of the advantages/disadvantages and practical aspects of battery technologies and

  6. Modelling, simulation and applications of longitudinal train dynamics

    Science.gov (United States)

    Cole, Colin; Spiryagin, Maksym; Wu, Qing; Sun, Yan Quan

    2017-10-01

    Significant developments in longitudinal train simulation and an overview of the approaches to train models and modelling vehicle force inputs are firstly presented. The most important modelling task, that of the wagon connection, consisting of energy absorption devices such as draft gears and buffers, draw gear stiffness, coupler slack and structural stiffness is then presented. Detailed attention is given to the modelling approaches for friction wedge damped and polymer draft gears. A significant issue in longitudinal train dynamics is the modelling and calculation of the input forces - the co-dimensional problem. The need to push traction performances higher has led to research and improvement in the accuracy of traction modelling which is discussed. A co-simulation method that combines longitudinal train simulation, locomotive traction control and locomotive vehicle dynamics is presented. The modelling of other forces, braking propulsion resistance, curve drag and grade forces are also discussed. As extensions to conventional longitudinal train dynamics, lateral forces and coupler impacts are examined in regards to interaction with wagon lateral and vertical dynamics. Various applications of longitudinal train dynamics are then presented. As an alternative to the tradition single wagon mass approach to longitudinal train dynamics, an example incorporating fully detailed wagon dynamics is presented for a crash analysis problem. Further applications of starting traction, air braking, distributed power, energy analysis and tippler operation are also presented.

  7. Advances in Electrochemical Models for Predicting the Cycling Performance of Traction Batteries: Experimental Study on Ni-MH and Simulation Développement de modèles électrochimiques de batteries de traction pour la prédiction de performances : étude expérimentale de batteries NiMH et simulations

    Directory of Open Access Journals (Sweden)

    Bernard J.

    2009-11-01

    Full Text Available Rigorous electrochemical models to simulate the cycling performance of batteries have been successfully developed and reported in the literature. They constitute a very promising approach for State-of-Charge (SoC estimation based on the physics of the cell with regards to other methods since SoC is an internal parameter of these physical models. However, the computational time needed to solve electrochemical battery models for online applications requires to develop a simplified physics-based battery model. In this work, our goal is to present and validate an advanced 0D-electrochemical model of a Ni-MH cell, as an example. This lumped-parameter model will be used to design an extended Kalman filter to predict the SoC of a Ni-MH pack. It is presented, followed by an extensive experimental study conducted on Ni-MH cells to better understand the mechanisms of physico-chemical phenomena occurring at both electrodes and support the model development. The last part of the paper focuses on the evaluation of the model with regards to experimental results obtained on Ni-MH sealed cells but also on the related commercial HEV battery pack. Des modèles électrochimiques fins permettant de simuler le comportement de batteries ont été développés avec succès et reportés dans la littérature. Ils constituent une alternative aux méthodes classiques pour estimer l’état de charge (SoC pour State of Charge des batteries, cette variable étant ici un paramètre interne du modèle physique. Cependant, pour les applications embarquées, il est nécessaire de développer des modèles simplifiés sur la base de ces modèles physiques afin de diminuer le temps de calcul nécessaire à la résolution des équations. Ici, nous présenterons à titre d’exemple un modèle électrochimique 0D avancé d’un accumulateur NiMH et sa validation. Ce modèle à paramètres concentrés sera utilisé pour réaliser un filtre de Kalman qui permettra la prédiction de l

  8. Open Abdomen Therapy with Vacuum and Mesh Mediated Fascial Traction After Aortic Repair: an International Multicentre Study.

    Science.gov (United States)

    Acosta, Stefan; Seternes, Arne; Venermo, Maarit; Vikatmaa, Leena; Sörelius, Karl; Wanhainen, Anders; Svensson, Mats; Djavani, Khatereh; Björck, Martin

    2017-12-01

    Open abdomen therapy may be necessary to prevent or treat abdominal compartment syndrome (ACS). The aim of the study was to analyse the primary delayed fascial closure (PDFC) rate and complications after open abdomen therapy with vacuum and mesh mediated fascial traction (VACM) after aortic repair and to compare outcomes between those treated with open abdomen after primary versus secondary operation. This was a retrospective cohort, multicentre study in Sweden, Finland, and Norway, including consecutive patients treated with open abdomen and VACM after aortic repair at six vascular centres in 2006-2015. The primary endpoint was PDFC rate. Among 191 patients, 155 were men. The median age was 71 years (IQR 66-76). Ruptured abdominal aortic aneurysm (RAAA) occurred in 69.1%. Endovascular/hybrid and open repairs were performed in 49 and 142 patients, respectively. The indications for open abdomen were inability to close the abdomen (62%) at primary operation and ACS (80%) at secondary operation. Duration of open abdomen was 11 days (IQR 7-16) in 157 patients alive at open abdomen termination. The PDFC rate was 91.8%. Open abdomen initiated at primary (N=103), compared with secondary operation (N=88), was associated with less severe initial open abdomen status (p=.006), less intestinal ischaemia (p=.002), shorter duration of open abdomen (p=.007), and less renal replacement therapy (RRT, popen abdomen initiated at primary versus secondary operation. VACM was associated with a high PDFC rate after prolonged open abdomen therapy following aortic repair. Patient outcomes seemed better when open abdomen was initiated at primary, compared with secondary operation but a selection effect is possible. Copyright © 2017 European Society for Vascular Surgery. Published by Elsevier Ltd. All rights reserved.

  9. THE MATHEMATIC STIMULATION OF TRANSIENT PROCESS IN A.C. – SYSTEM “ELECTRIC-TRACTION NETWORK – LOCOMOTIVE” 3. SWITCHING ON MAIN POWER CONVERTER IN “FREE PLAY” MODE; THE ANALYSIS OF VOLTS AND CURRENTS IN THE POWER SUPPLY INPUT SYSTEM

    Directory of Open Access Journals (Sweden)

    T. M. Mischenko

    2011-05-01

    Full Text Available The article is a continuation of analysis of the electric equivalent AC circuit «traction substation − device of transversal compensation − electric-traction network − electric locomotive DS 3» and the influence on a power transformer in the idle mode, depending on the feeder voltage and the distance of an electric locomotive from a traction substation. The numeral calculations are performed and the voltage and current values in the electric power supply system are analyzed.

  10. THE MATHEMATIC STIMULATION OF TRANSIENT PROCESS IN A.C. – SYSTEM “ELECTRIC-TRACTION NETWORK – LOCOMOTIVE” 3. SWITCHING ON MAIN POWER CONVERTER IN “FREE PLAY” MODE; THE ANALYSIS OF VOLTS AND CURRENTS IN THE POWER SUPPLY INPUT SYSTEM

    OpenAIRE

    T. M. Mischenko

    2011-01-01

    The article is a continuation of analysis of the electric equivalent AC circuit «traction substation − device of transversal compensation − electric-traction network − electric locomotive DS 3» and the influence on a power transformer in the idle mode, depending on the feeder voltage and the distance of an electric locomotive from a traction substation. The numeral calculations are performed and the voltage and current values in the electric power supply system are analyzed.

  11. Smart Battery Thermal Management for PHEV Efficiency Une gestion avancée de la thermique de la batterie basse tension de traction pour optimiser l’efficacité d’un véhicule hybride électrique rechargeable

    Directory of Open Access Journals (Sweden)

    Lefebvre L.

    2013-03-01

    la disponibilité d’énergie de traction électrique et la durabilité de la batterie. La conception du système de gestion thermique de la batterie basse tension doit donc prendre en compte les exigences requises de la chaîne de traction et du véhicule, la conception et l’architecture du pack batterie, les contraintes d’environnement, au moindre coût et au moindre poids, etc., tout en optimisant les compromis entre ces paramètres souvent antagonistes. Le processus de conception du thermomanagement de la batterie basse tension de traction fait l’objet de la première partie de cet article. Ce processus sera illustré par deux exemples, l’un mettant en oeuvre l’air en provenance de l’habitacle du véhicule et l’autre, par un refroidissement direct via le circuit de réfrigération du véhicule. Pour une application concrète, le processus de décision doit intégrer l’ensemble des modes de thermomanagement étudiés dans ce contexte et les différents paramètres et exigences pris en compte en tant que données d’entrée. La seconde partie de l’article présente un modèle de simulation thermoélectrique simplifié de la batterie basse tension de traction. Quelques résultats de calculs seront présentés à titre d’exemples dans deux perspectives différentes, d’une part, le dimensionnement thermique du système de thermomanagement, et d’autre part, l’optimisation du bilan énergétique du véhicule. Par ailleurs, ce modèle de simulation simplifié a également permis d’identifier et d’évaluer plusieurs stratégies pertinentes de gestion thermique de la batterie. Ces stratégies visent à améliorer l’efficacité et la performance du véhicule tout en ménageant la durée de vie de la batterie. La troisième partie présente certaines de ces stratégies. Parmi celles-ci, le post-refroidissement et le préconditionnement thermique de la batterie basse tension de traction, en préchauffage par conditions froides et en

  12. The effects of cervical traction, cranial rhythmic impulse, and Mckenzie exercise on headache and cervical muscle stiffness in episodic tension-type headache patients.

    Science.gov (United States)

    Choi, Sung-Yong; Choi, Jung-Hyun

    2016-03-01

    [Purpose] The purpose of this study was to examine the effects of cervical traction treatment, cranial rhythmic impulse treatment, a manual therapy, and McKenzie exercise, a dynamic strengthening exercise, on patients who have the neck muscle stiffness of the infrequent episodic tension-type (IETTH) headache and frequent episodic tension-type headache(FETTH), as well as to provide the basic materials for clinical interventions. [Subjects] Twenty-seven subjects (males: 15, females: 12) who were diagnosed with IETTH and FETTH after treatment by a neurologist were divided into three groups: (a cervical traction group (CTG, n=9), a cranial rhythmic contractiongroup (CRIG, n=9), and a McKenzie exercise group (MEG, n=9). An intervention was conducted for each group and the differences in their degrees of neck pain and changes in muscle tone were observed. [Results] In the within-group comparison of each group, headache significantly decreased in CTG. According to the results of the analysis of the muscle tone of the upper trapezius, there was a statistically significant difference in MEG on the right side and in CRIG on the left side. According to the results of the analysis of the muscle tone of the sternocleidomastoid muscle, there was a statistically significant difference in MEG on the right side and in CRIG on the left side. [Conclusion] In the comparison of the splenius capitis muscle between the groups, there was a statistically significant difference on the right side. Hence, compared to the other methods, cervical traction is concluded to be more effective at reducing headaches in IETTH and FETTH patients.

  13. Black patients sustain vision loss while White and South Asian patients gain vision following delamination or segmentation surgery for tractional complications associated with proliferative diabetic retinopathy.

    Science.gov (United States)

    Mastropasqua, R; Luo, Y H-L; Cheah, Y S; Egan, C; Lewis, J J; da Cruz, L

    2017-10-01

    PurposeThis retrospective comparative case series aims to determine whether patient ethnicity (White versus South Asian versus Black) is related to the outcome of surgical treatment for traction complications of severe proliferative diabetic retinopathy (PDR).SettingMoorfields Eye Hospital London, UK.MethodsAll patients who underwent vitrectomy with, delamination and/or segmentation for PDR over a 5-year period (2009-2014) were reviewed retrospectively. Patients were divided into White, South Asian or Black groups, and their age, gender, HbA1C and type of diabetes were recorded. A total of 484 patients (253 White, 117 South Asian, 114 Black) were included. Twenty-one patients were excluded due to inadequate documentation.OutcomesLogMAR Visual acuity (converted from Snellen) (VA), was recorded pre-operatively and ~6 months post surgery (range 5-8 months). Surgical outcome was classified according to the type and duration of tamponade required post-operatively.ResultsPre-operative VA and HbA1C values were similar across all three ethnic groups (P=0.64 and 0.569, respectively). Change in VA (mean±SD) was 0.41±0.78, 0.14±0.76 and -0.26±0.57 in White, South Asian and Black patient groups respectively (PAsian patient groups.ConclusionsThis study demonstrates that Black patients on average lose vision following delamination surgery for traction complications of PDR while White and South Asian patients gain vision. The same group is also at higher risk of retaining silicone more than 6 months after surgery. This difference remains even when corrected for glycaemic control. The higher risk of visual loss and long-term retention of silicone oil in black patients requires further investigation. If these results are confirmed, surgeons should consider their patients' ethnicity before proceeding with surgical treatment of diabetic tractional detachment.

  14. THE SIX-WHEEL FRIGHT TRUCK LOCOMOTIVE OF DOUBLE DELIVERY USES RADIO-FREQUENCY TRANSFER WITH PADDING AND ASYNCHRONIZED TRACTION IMPELLENTS

    Directory of Open Access Journals (Sweden)

    M. H. Visin

    2010-10-01

    Full Text Available Our research offers a new perspective loading pattern of the 12-wheel double-feed freight electric locomotive with the asynchronous tractive motor using an adapter transformer with the high-frequency uncoupler. This will make it possible to decrease the traction-feeding transformer mass 2.3 times, to remove the current pulse advancing on the track circuit and therefore the influence on the work of the ALSE and CBS. So the railway traffic safety will be increased considerably.

  15. Direct observation of CD4 T cell morphologies and their cross-sectional traction force derivation on quartz nanopillar substrates using focused ion beam technique

    Science.gov (United States)

    Kim, Dong-Joo; Kim, Gil-Sung; Hyung, Jung-Hwan; Lee, Won-Yong; Hong, Chang-Hee; Lee, Sang-Kwon

    2013-07-01

    Direct observations of the primary mouse CD4 T cell morphologies, e.g., cell adhesion and cell spreading by culturing CD4 T cells in a short period of incubation (e.g., 20 min) on streptavidin-functionalized quartz nanopillar arrays (QNPA) using a high-content scanning electron microscopy method were reported. Furthermore, we first demonstrated cross-sectional cell traction force distribution of surface-bound CD4 T cells on QNPA substrates by culturing the cells on top of the QNPA and further analysis in deflection of underlying QNPA via focused ion beam-assisted technique.

  16. The dual-system traction equipment of the high speed train Velaro for Russia; Die Mehrsystemtraktionsausruestung des Hochgeschwindigkeitszuges Velaro fuer Russland

    Energy Technology Data Exchange (ETDEWEB)

    Horstmann, D.; Budzinski, F.; Pirwitz, J. [Siemens AG, Erlangen (Germany)

    2007-07-01

    As from 2009 eight high speed trainsets of the Velaro-family will be delivered to Russia. The ten-car trainsets with distributed traction equipment are intended for service on all high speed lines in Russia, starting with the Moscow - St. Petersburg line. They will be supplied in two variants, single- and dual-system trainsets, so that they are deployable in a broad area. Furthermore the Russian standards and specifics have to be considered. The track gauge in Russia is 1520 mm instead of 1435 mm as common in Europe and the cold and snowy winters require a special ventilation- or cooling system. (orig.)

  17. Evaluation of traction stirrup distraction technique to increase the joint space of the shoulder joint in the dog: A cadaveric study.

    Science.gov (United States)

    Devesa, V; Rovesti, G L; Urrutia, P G; Sanroman, F; Rodriguez-Quiros, J

    2015-06-01

    The objective of this study was to evaluate technical feasibility and efficacy of a joint distraction technique by traction stirrup to facilitate shoulder arthroscopy and assess potential soft tissue damage. Twenty shoulders were evaluated radiographically before distraction. Distraction was applied with loads from 40 N up to 200 N, in 40 N increments, and the joint space was recorded at each step by radiographic images. The effects of joint flexion and intra-articular air injection at maximum load were evaluated. Radiographic evaluation was performed after distraction to evaluate ensuing joint laxity. Joint distraction by traction stirrup technique produces a significant increase in the joint space; an increase in joint laxity could not be inferred by standard and stress radiographs. However, further clinical studies are required to evaluate potential neurovascular complications. A wider joint space may be useful to facilitate arthroscopy, reducing the likelihood for iatrogenic damage to intra-articular structures. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Idiopathic pulmonary fibrosis may be a disease of recurrent, tractional injury to the periphery of the aging lung: a unifying hypothesis regarding etiology and pathogenesis.

    Science.gov (United States)

    Leslie, Kevin O

    2012-06-01

    Idiopathic pulmonary fibrosis is a progressive, fatal lung disease occurring in older individuals. Despite 50 years of accrued data about the disease, little progress has been made in slowing functional loss or in decreasing patient mortality. To present a novel hypothesis on the etiology and pathogenesis of idiopathic pulmonary fibrosis. Published data are reviewed regarding the epidemiology, clinical presentation, natural history, radiologic findings, and pathologic findings in patients with idiopathic pulmonary fibrosis. Patients with idiopathic pulmonary fibrosis may be predisposed genetically to tractional injury to the peripheral lung. The result is recurrent damage to the epithelial-mesenchymal interface, preferentially at the outer edges of the basilar lung lobules where tractional stress is high during inspiration, compliance is relatively low, and there is a greater tendency for alveolar collapse at end-expiration. A distinctive "reticular network of injury" (the fibroblast focus) forms, attended by a prolonged phase of wound repair (tear and slow repair). Discrete areas of alveolar collapse are observed in scar at the periphery of the lung lobules. The cycle repeats over many years resulting in progressive fibrous remodeling and replacement of the alveoli in a lobule by bronchiolar cysts surrounded by scar (honeycomb lung). Abnormalities in surfactant function are proposed as a potential mechanism of initial lung damage. Age of onset may be a function of a required threshold of environmental exposures (eg, cigarette smoking) or other comorbid injury to the aging lung. Evidence supporting this hypothesis is presented and potential mechanisms are discussed. A potential role for contributing cofactors is presented.

  19. Subcontract Report: Final Report on Assessment of Motor Technologies for Traction Drives of Hybrid and Electric Vehicles (Subcontract #4000080341)

    Energy Technology Data Exchange (ETDEWEB)

    Fezzler, Raymond [BIZTEK Consulting, Inc.

    2011-03-01

    Currently, interior permanent magnet (IPM) motors with rare-earth (RE) magnets are almost universally used for hybrid and electric vehicles (EVs) because of their superior properties, particularly power density. However, there is now a distinct possibility of limited supply or very high cost of RE magnets that could make IPM motors unavailable or too expensive. Because development of electric motors is a critical part of the U.S. Department of Energy (DOE) Advanced Power Electronics and Motors activity, DOE needs to determine which options should be investigated and what barriers should be addressed. Therefore, in order to provide a basis for deciding which research topics should be pursued, an assessment of various motor technologies was conducted to determine which, if any, is potentially capable of meeting FreedomCAR 2015 and 2020 targets. Highest priority was given to IPM, surface mounted permanent magnet (SPM), induction, and switched reluctance (SR) motors. Also of interest, but with lesser emphasis, were wheel motors, multiple-rotor motors, motors with external excitation, and several others that emerged from the assessment. Cost and power density (from a design perspective, the power density criterion translates to torque density) are emerging as the two most important properties of motors for traction drives in hybrid and EVs, although efficiency and specific power also are very important. The primary approach for this assessment involved interviews with original equipment manufacturers (OEMs), their suppliers, and other technical experts. For each technology, the following issues were discussed: (1) The current state-of-the-art performance and cost; (2) Recent trends in the technology; (3) Inherent characteristics of the motor - which ones limit the ability of the technology to meet the targets and which ones aid in meeting the target; (4) What research and development (R&D) would be needed to meet the targets; and (5) The potential for the technology to

  20. All Electric Combat Vehicles (AECV) for Future Applications

    Science.gov (United States)

    2004-07-01

    virtue of their greater specific performance and their good efficiency – benefits that are particularly applicable to permanent - magnet motors . Once again...asynchronous motors, the development of permanent - magnet motors is focused on the actual motor rather than on the motor’s electronics. Figure 6.1 displays the...keep the Si semiconductor devices (IGBT) from failing. Similarly, the permanent magnet motors which are desirable for traction because of their high

  1. Energy-saving measures in the electrocar. Pt. 1 and 2. 1. Energy-optimized recuperative braking. 2. Energy-optimized charging of traction batteries; Energiesparmassnahmen am Elektroauto. T. 1 und 2. T. 1: Energieoptimiertes rekuperatives Bremsen. T. 2: Energieoptimiertes Laden von Traktionsbatterien

    Energy Technology Data Exchange (ETDEWEB)

    Goetting, G.; Willer, B.; Knorr, R.

    2001-07-01

    The first part of the research project was titled ''energy-optimized recuperative braking''. In this part, several braking strategies, especially those for use in electro vehicles which in addition to the mechanical brakes of the vehicle also incorporate the electrical drive into the brake system were compared with the support of a simulation model and evaluated. The paper reports both on the simulation model used and on the possibilities of saving energy which can be achieved using the various braking strategies for differing driving cycles. In the second part of the research project, ''energy-optimized charging of traction batteries'', possible methods of charging traction batteries of electro vehicles are shown and assessed with regard to the battery efficiency under various conditions of application. [German] In dem unter der Ueberschrift 'Energieoptimiertes rekuperatives Bremsen' laufenden ersten Teil des Forschungsvorhabens wurden verschiedene und speziell fuer den Einsatz im Elektrofahrzeug entworfene Bremsstrategien, die neben den mechanischen Bremsen des Fahrzeugs auch den elektrischen Antrieb in das Bremssystem einbeziehen, mit Hilfe eines Simulationsmodells verglichen und bewertet. Im Bericht werden sowohl das verwendete Simulationsmodell erlaeutert als auch die energetischen Einsparmoeglichkeiten, die sich mit den verschiedenen Bremsstrategien fuer unterschiedliche Fahrzyklen erzielen lassen, aufgezeigt. Im zweiten Teil des Forschungsvorhabens ('Energieoptimiertes Laden von Traktionsbatterien') wurden moegliche Ladeverfahren fuer Traktionsbatterien von Elektrofahrzeugen aufgezeigt und hinsichtlich des Batteriewirkungsgrades bei unterschiedlichen Einsatzbedingungen beurteilt. In die Untersuchungen waren Blei-, NiMH-, NaNiCl{sub 2}- und Lithium-Batterien eingeschlossen. (orig.)

  2. The effects of infrared laser therapy and weightbath traction hydrotherapy as components of complex physical treatment in disorders of the lumbar spine: a controlled pilot study with follow-up

    Science.gov (United States)

    Oláh, Csaba; Oláh, Mihály; Demeter, Béla; Jancsó, Zoltán; Páll, Valéria; Bender, Tamás

    2010-02-01

    Introduction: The therapeutic modalities available for the conservative management of chronic lumbar pain included infrared laser therapy and underwater traction, which usefulness is not universally acknowledged. This study was intended to ascertain any beneficial impact of infrared laser therapy and weightbath treatment on the clinical parameters and quality of life of patients with lumbar discopathy. Material and methods: The study population comprised 54 randomised subjects. I. group of 18 patents received only infrared laser therapy to lumbar region and painful Valley points. II. group of 18 subjects each received underwater traction therapy of lumbar spine with add-on McKenzie exercise and iontophoresis. The remaining III. group treated with exercise and iontophoresis, served as control. VAS, Oswestry index, SF36 scores, range of motion, neurological findings and thermography were monitored to appraise therapeutic afficacy in lumbar discopathy. A CT or MRI scan was done at baseline and after 3 months follow-up. Result:Infrared laser therapy and underwater traction for discopathy achieved significant improvement of all study parameters, which was evident 3 months later. Among the controls, significant improvement of only a single parameter was seen in patients with lumbar discopathy. Conclusions: Infrared laser therapy and underwater traction treatment effectively mitigate pain, muscle spasms, enhance joint flexibility, and improve the quality of life of patients with lumbar discopathy.

  3. A Harmonic Resonance Suppression Strategy for a High-Speed Railway Traction Power Supply System with a SHE-PWM Four-Quadrant Converter Based on Active-Set Secondary Optimization

    Directory of Open Access Journals (Sweden)

    Runze Zhang

    2017-10-01

    Full Text Available Pulse width modulation (PWM technology is widely used in traction converters for high-speed railways. The harmonic distribution caused by PWM is quite extensive, and increases the possibility of grid–train coupling resonance in the traction power supply system (TPSS. This paper first analyzes the mechanism of resonance, when the characteristic harmonic frequency of a four-quadrant converter (4QC current that injects into the traction grid matches the resonant frequency of the traction grid, which may result in resonance in the system. To suppress resonance, this paper adopts specific harmonic elimination–pulse width modulation (SHE-PWM technology combined with a transient direct current control strategy to eliminate the harmonics in the resonant frequency, which may suppress the grid–train coupling resonance. Due to the fact that the SHE-PWM process with multiple switching angles contains complex transcendental equations, the initial value is difficult to provide, and is difficult to solve using ordinary iterative algorithms. In this paper, an active-set secondary optimization method is used to solve the equation. The algorithm has the benefits of low dependence on initial values, fast convergence and high solution accuracy. Finally, the feasibility of the resonant suppression algorithm is verified by means of Matlab simulation.

  4. Matching of traction control systems for all-wheel devices by means of a virtual driver model; Abstimmung von Traktionsregelsystemen fuer Allradfahrzeuge mit Hilfe eines virtuellen Fahrermodells

    Energy Technology Data Exchange (ETDEWEB)

    Vockenhuber, Mario [MAGNA Powertrain AG und Co. KG, Lannach (Austria); Fischer, Rainer [Magna Powertrain, Engineering Center Steyr, St. Valentin (Austria); Butz, Torsten; Ehmann, Martin [TESIS DYNAware GmbH, Muenchen (Germany)

    2011-07-01

    Simulation of the full vehicle dynamics is an efficient means for function development and validation as well as calibration of traction control systems for four-wheel drive vehicles. Simulation models for vehicle, control systems and environment with a suitable level of detail are used to investigate different layout variants of the drivetrain on various tracks. This contribution outlines a driver model which enables considering the influence of different driving styles. Various human driver types are depicted by specific controller parameterization or definition of reference values for longitudinal and lateral vehicle guidance. Thus, apart from the calibration of control system electronics also realistic load spectra for durability computations of mechanical components can be determined via simulation. (orig.)

  5. Design and Experimental Investigations on a new ZCS Non-Isolated Bidirectional Converter based on Auxiliary resonant Circuit for DC Traction Vehicles

    Directory of Open Access Journals (Sweden)

    Veera Venkata Subrahmanya Kumar Bhajana

    2017-12-01

    Full Text Available This paper proposes a new ZCS non-isolated bidirectional converter for energy storage systems in DC Traction vehicles. The conventional hard-switched non-isolated bidirectional converter is additionally assisted with an auxiliary resonant cell, which is implemented with auxiliary IGBTs, resonant inductor and capacitor will provide the zero current switching, while the main IGBT commutates. This paper mainly deals with the design analysis, simulation and experimental investigations of the proposed converter are provided to prove the soft-switching capability and its overall performance. The 100-200V/2kW laboratory prototype has been implemented and tested to verify the theoretical assumptions and simulation results.

  6. Usefulness of a traction method using dental floss and a hemoclip for gastric endoscopic submucosal dissection: a propensity score matching analysis (with videos).

    Science.gov (United States)

    Suzuki, Sho; Gotoda, Takuji; Kobayashi, Yoshiyuki; Kono, Shin; Iwatsuka, Kunio; Yagi-Kuwata, Naoko; Kusano, Chika; Fukuzawa, Masakatsu; Moriyasu, Fuminori

    2016-02-01

    Although endoscopic submucosal dissection (ESD) is a significant advancement in therapeutic endoscopy, it is a complicated technique and requires considerable expertise. In this exploratory study, we evaluated the efficacy of a simple traction method that uses dental floss and a hemoclip (DFC) and was developed to overcome the technical difficulties of ESD. In total, 238 early gastric cancers treated by ESD between May 2012 and December 2014 at Tokyo Medical University were retrospectively reviewed. Lesions treated by conventional ESD (n = 185) and by ESD with DFC (ESD-DFC) (n = 53) were compared. Multivariable analyses and propensity score matching were used to compensate for the differences in age, sex, resected specimen size, lesion location, lesion position, presence of ulceration, and operator level. The procedure time, rate of en bloc and complete resection, and rates of adverse events were evaluated between the 2 groups. Propensity score matching analysis created 43 matched pairs. Adjusted comparisons between ESD-DFC and conventional ESD showed similar treatment outcomes (en bloc resection rate: 97.7% vs 100%, P = .315; complete resection rate: 90.7% vs 95.3%, P = .397; perforation during ESD rate: 2.3% vs 2.3%, P = 1.000; post-ESD bleeding rate: 4.7% vs 4.7%, P = 1.000) but a significantly shorter procedure time for ESD-DFC (82.2 ± 79.5 minutes vs 118.2 ± 71.6 minutes, P = .002). ESD-DFC facilitated rapid ESD with good visualization and traction while ensuring high curability and safety. Copyright © 2016 American Society for Gastrointestinal Endoscopy. Published by Elsevier Inc. All rights reserved.

  7. Tensile deformations in mono- and polycrystalline uranium between 20 deg. C and -196 deg. C; Deformation par traction de l'uranium mono- et polycristallin entre 20 deg. C et -196 deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Lemogne, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-06-01

    Tensile stress tests been carried out at low temperatures (between 20 C and -196 C) on monocrystalline and polycrystalline uranium of various purities. The mechanical properties of the monocrystals have been related, at all temperatures, to plastic flow mechanisms. Below -100 C brittle fracture occurs on the planes making up the twins. A detailed study of the plastic behaviour at -196 C has made it possible to show that all the twin planes except the [176] plane were liable to become privileged planes for brittle fracture. The mechanical properties of the polycrystals, the breaking stress and the elongation at breaking point, decrease as the temperature decreases from 20 to -196 C; they undergo a transition however - not to be confused with the ductile-brittle transition - whose position and strength depend on the grain size and on the purity. It has been verified also that Petch's law is approximately applicable to the plastic flow and rupture stresses; a study has also been made of the influence of temperature and purity on the constants occurring in this equation. Finally, experiments at -196 C on the deformation up to breaking point of polycrystalline samples cold-worked at 20 C have shown the importance of the role played by intergranular cracks in the plastic behaviour of uranium. (author) [French] Des essais de traction ont ete realises a basse temperature (entre 20 C et -196 C, sur des monocristaux et des polycristaux d'uranium de differentes puretes. Les proprietes mecaniques des monocristaux ont ete reliees, a toutes temperatures, aux mecanismes d'ecoulement plastique. Une rupture fragile intervient a partir de -100 C sur les plans de composition de macle. L'etude detaillee du comportement plastique a -196 C a permis de preciser que tous les plans de macle, sauf [176], etaient susceptibles de devenir des plans de rupture fragile privilegies. Les proprietes mecaniques des polycristaux, contrainte de rupture et allongement a la rupture, decroissent quand on

  8. Development of free running differential. Development of differential with an actuator and a clutch which disconnects the traction; Free running defu no kaihatsu. Kirippanashi kiko oyobi actuator wo naizoshita differential sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, N; Teraoka, M; Ishikawa, O; Nagaoka, T; Ugajin, K [Tochigi Fuji Sangyo Co. Ltd., Tochigi (Japan)

    1997-10-01

    Free Running Differential has an effect on fuel economy and noise reduction from drive line for four wheel drive vehicle. It has an actuator and a clutch which disconnects the traction from no driving side tire when two wheel drive is selected. this unit can be installed in conventional differential carrier with no design change. It is compact in design and low in cost. We evaluate it as having a dominant position among any other Free running system. 7 figs.

  9. [Retrospective analysis of effects of metacarpus and phalanx traction on correction of scar contracture of hand after burn on the palm side].

    Science.gov (United States)

    Chunsheng, Hou; Qingye, Liu; Hongfei, Hao; Yuying, Dong; Feng, Wang; Jin, Lei

    2015-06-01

    To analyze the effects of metacarpus and phalanx traction on correction of scar contracture of hand after burn on the palm side retrospectively. A total of 32 patients with 39 affected hands with scar contracture on the palm side after burn were hospitalized from May 2010 to December 2014. Method of treatment: scar contracture was conservatively released followed by skin grafting, which was referred to as method A; Kirschner wire was inserted into the middle or distal phalanx of finger with contracture and the corresponding metacarpus in the shape of U for 2 to 7 weeks' traction, which was referred to as method B; traction frame was built based on the traction pile and anchor formed by Kirschner wire inserted through the second to the fifth metacarpus and distal phalanx of finger with contracture, and then the affected fingers were pulled into a straight position with rubber bands for 2 to 6 months, which was referred to as method C. Method A was used in patients who would be treated with thorough release of scar followed by skin grafting routinely. Method B was used in patients who would be treated with intramedullary Kirschner wire fixation after release of scar contracture and skin transplantation routinely. Method C was further used in patients when methods A and B failed to accomplish the expected result. Method C was used in the first place followed by method A in whom there might be vascular decompensation or exposure of tendon and bone after scar release, and those who failed to meet the expectation were treated with method C in addition. Patients who were unwilling to undergo surgery were treated with method C exclusively. During the course of treatment, the presence or absence of infection and slipping of Kirschner wire or its slitting through soft tissue were observed. The presence or absence of tendency of recurrence of scar contracture within 1 to 2 weeks after treatment was observed. The length of palmar skin measuring from the root of finger with

  10. A tyre slip-based integrated chassis control of front/rear traction distribution and four-wheel independent brake from moderate driving to limit handling

    Science.gov (United States)

    Joa, Eunhyek; Park, Kwanwoo; Koh, Youngil; Yi, Kyongsu; Kim, Kilsoo

    2018-04-01

    This paper presents a tyre slip-based integrated chassis control of front/rear traction distribution and four-wheel braking for enhanced performance from moderate driving to limit handling. The proposed algorithm adopted hierarchical structure: supervisor - desired motion tracking controller - optimisation-based control allocation. In the supervisor, by considering transient cornering characteristics, desired vehicle motion is calculated. In the desired motion tracking controller, in order to track desired vehicle motion, virtual control input is determined in the manner of sliding mode control. In the control allocation, virtual control input is allocated to minimise cost function. The cost function consists of two major parts. First part is a slip-based tyre friction utilisation quantification, which does not need a tyre force estimation. Second part is an allocation guideline, which guides optimally allocated inputs to predefined solution. The proposed algorithm has been investigated via simulation from moderate driving to limit handling scenario. Compared to Base and direct yaw moment control system, the proposed algorithm can effectively reduce tyre dissipation energy in the moderate driving situation. Moreover, the proposed algorithm enhances limit handling performance compared to Base and direct yaw moment control system. In addition to comparison with Base and direct yaw moment control, comparison the proposed algorithm with the control algorithm based on the known tyre force information has been conducted. The results show that the performance of the proposed algorithm is similar with that of the control algorithm with the known tyre force information.

  11. Evaluation of Interlaminar Stresses in Composite Laminates with a Bolt-Filled Hole Using a Linear Elastic Traction-Separation Description

    Directory of Open Access Journals (Sweden)

    Yong Cao

    2017-01-01

    Full Text Available Determination of the local interlaminar stress distribution in a laminate with a bolt-filled hole is helpful for optimal bolted joint design, due to the three-dimensional (3D nature of the stress field near the bolt hole. A new interlaminar stress distribution phenomenon induced by the bolt-head and clamp-up load, which occurs in a filled-hole composite laminate, is investigated. In order to efficiently evaluate interlaminar stresses under the complex boundary condition, a calculation strategy that using zero-thickness cohesive interface element is presented and validated. The interface element is based on a linear elastic traction-separation description. It is found that the interlaminar stress concentrations occur at the hole edge, as well as the interior of the laminate near the periphery of the bolt head. In addition, the interlaminar stresses near the periphery of the bolt head increased with an increase in the clamp-up load, and the interlaminar normal and shear stresses are not at the same circular position. Therefore, the clamp-up load cannot improve the interlaminar stress distribution in the laminate near the periphery of the bolt head, although it can reduce the magnitude of the interlaminar shear stress at the hole edge. Thus, the interlaminar stress distribution phenomena may lead to delamination initiation in the laminate near the periphery of the bolt head, and should be considered in composite bolted joint design.

  12. Effects of hydrogen on the tensile strength characteristics of stainless steels; Effets de l'hydrogene sur les caracteristiques de rupture par traction d'aciers inoxydables

    Energy Technology Data Exchange (ETDEWEB)

    Blanchard, R; Pelissier, J; Pluchery, M [Commissariat a l' Energie Atomique, Grenoble (France).Centre d' Etudes Nucleaires; Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1961-07-01

    This paper deals with the effects of hydrogen on stainless steel, that might possibly be used as a canning material in hydrogen-cooled reactors. Apparent ultimate-tensile strength is only 80 per cent of initial value for hydrogen content about 50 cc NTP/ 100 g, and reduction in area decreases from 80 to 55 per cent. A special two-stage replica technique has been developed which allows fracture surface of small tensile specimens (about 0.1 mm diam.) to be examined in an electron microscope. All the specimens showed evidence of ductile character throughout the range of hydrogen contents investigated, but the aspect of the fracture surfaces gradually changes with increasing amounts. (author) [French] On etudie les effets de l'hydrogene sur des aciers inoxydables, qui sont des materiaux de gainage possibles pour des reacteurs utilisant l'hydrogene comme gaz de refroidissement. On montre que la charge apparente de rupture a la traction n'est plus que 80 pour cent de sa valeur initiale lorsque la teneur en hydrogene atteint 50 cc TPN/ 100 g, et que la striction passe dans ces conditions de 80 a 55 pour cent. L'examen microfractographique qui a ete effectue avec succes par une technique de double replique malgre la petitesse des echantillons (0,3 mm de diametre environ), revele que tout en gardant un caractere ductile, l'aspect des surfaces de rupture evolue notablement avec la teneur en hydrogene. (auteur)

  13. Comparison of clinical outcomes of multi-point umbrella suturing and single purse suturing with two-point traction after procedure for prolapse and hemorrhoids (PPH) surgery.

    Science.gov (United States)

    Jiang, Huiyong; Hao, Xiuyan; Xin, Ying; Pan, Youzhen

    2017-11-01

    To compare the clinical outcomes of multipoint umbrella suture and single-purse suture with two-point traction after procedure for prolapse and hemorrhoids surgery (PPH) for the treatment of mixed hemorrhoids. Ninety patients were randomly divided into a PPH plus single-purse suture group (Group A) and a PPH plus multipoint umbrella suture (Group B). All operations were performed by an experienced surgeon. Operation time, width of the specimen, hemorrhoids retraction extent, postoperative pain, postoperative bleeding, and length of hospitalization were recorded and compared. Statistical analysis was conducted by t-test and χ2 test. There were no significant differences in sex, age, course of disease, and degree of prolapse of hemorrhoids between the two groups. The operative time in Group A was significantly shorter than that in Group B (P hemorrhoid core retraction were significantly lower in Group B (P  0.05 for all comparisons) was observed. The multipoint umbrella suture showed better clinical outcomes because of its targeted suture according to the extent of hemorrhoid prolapse. Copyright © 2017. Published by Elsevier Ltd.

  14. Etude par resistivite electrique du comportement d'un alliage amorphe Fe 40Ni 38Mo 4B 18 deforme par traction

    Science.gov (United States)

    Hoang, Long Phan; Sacovy, Paulette; Delaplace, Jean

    1983-02-01

    Des rubans d'alliages amorphes Metglas du type Fe 40Ni 38Mo 4B 18 à l'état brut de trempe ont été déformés par traction à la température ambiante et l'on a suivi les variations de la résistance électrique des échantillons au cours de la déformation. Il ressort de ces essais que la déformation plastique qui est de l'ordre de 0.5% avant rupture ne se produit pas de faĉon homogène dans l'échantillon. Les mesures électriques effectuées au cours de la déformation mettent en évidence dans le domaine élastique un effet d'élastorésistance, relativement important ( K ≠ 1); elles montrent que dans le domaine plastique la déformation permanente des échantillons s'accompagne d'une diminution de la résistivité électrique du matériau. Deux hypothèses sont discutées pour expliquer cet effet inattendu, l'un qui fait appel à l'existence de volumes libres, l'autre qui suppose une cristallisation localisée du matériau sous l'effet de la contrainte.

  15. Low cost electronic ultracapacitor interface technique to provide load leveling of a battery for pulsed load or motor traction drive applications

    Science.gov (United States)

    King, Robert Dean; DeDoncker, Rik Wivina Anna Adelson

    1998-01-01

    A battery load leveling arrangement for an electrically powered system in which battery loading is subject to intermittent high current loading utilizes a passive energy storage device and a diode connected in series with the storage device to conduct current from the storage device to the load when current demand forces a drop in battery voltage. A current limiting circuit is connected in parallel with the diode for recharging the passive energy storage device. The current limiting circuit functions to limit the average magnitude of recharge current supplied to the storage device. Various forms of current limiting circuits are disclosed, including a PTC resistor coupled in parallel with a fixed resistor. The current limit circuit may also include an SCR for switching regenerative braking current to the device when the system is connected to power an electric motor.

  16. An Integrated Multifunctional Bidirectional AC/DC and DC/DC Converter for Electric Vehicles Applications

    OpenAIRE

    Liwen Pan; Chengning Zhang

    2016-01-01

    This paper presents an on-board vehicular battery charger that integrates bidirectional AC/DC converter and DC/DC converter to achieve high power density for application in electric vehicles (EVs). The integrated charger is able to transfer electrical energy between the battery pack and the electric traction system and to function as an AC/DC battery charger. The integrated charger topology is presented and the design of passive components is discussed. The control schemes are developed for m...

  17. Fast sol-gel synthesis of LiFePO{sub 4}/C for high power lithium-ion batteries for hybrid electric vehicle application

    Energy Technology Data Exchange (ETDEWEB)

    Beninati, Sabina; Damen, Libero; Mastragostino, Marina [University of Bologna, Department of Metal Science, Electrochemistry and Chemical Techniques, Via San Donato 15, 40127 Bologna (Italy)

    2009-12-01

    LiFePO{sub 4}/C of high purity grade was successfully synthesized by microwave accelerated sol-gel synthesis and showed excellent electrochemical performance in terms of specific capacity and stability. This cathode material was characterized in battery configuration with a graphite counter electrode by USABC-DOE tests for power-assist hybrid electric vehicle. It yielded a non-conventional Ragone plot that represents complexity of battery functioning in power-assist HEV and shows that the pulse power capability and available energy of such a battery surpasses the DOE goal for such an application. (author)

  18. MW-assisted synthesis of LiFePO 4 for high power applications

    Science.gov (United States)

    Beninati, Sabina; Damen, Libero; Mastragostino, Marina

    LiFePO 4/C was prepared by solid-state reaction from Li 3PO 4, Fe 3(PO 4) 2·8H 2O, carbon and glucose in a few minutes in a scientific MW (microwave) oven with temperature and power control. The material was characterized by X-ray diffraction, scanning electron microscopy and by TGA analysis to evaluate carbon content. The electrochemical characterization as positive electrode in EC (ethylene carbonate)-DMC (dimethylcarbonate) 1 M LiPF 6 was performed by galvanostatic charge-discharge cycles at C/10 to evaluate specific capacity and by sequences of 10 s discharge-charge pulses, at different high C-rates (5-45C) to evaluate pulse-specific power in simulate operative conditions for full-HEV application. The maximum pulse-specific power and, particularly, pulse efficiency values are quite high and make MW synthesis a very promising route for mass production of LiFePO 4/C for full-HEV batteries at low energy costs.

  19. Changes in stature during and after spinal traction in young male subjects Alterações na estatura antes e após a tração vertebral em homens jovens

    Directory of Open Access Journals (Sweden)

    ALF Rodacki

    2007-02-01

    Full Text Available BACKGROUND: Spinal traction is a relatively popular procedure for increasing the intervertebral space by applying separating forces. The parameters of time and magnitude of the traction forces may influence the outcomes from this procedure and need to be investigated. The duration of the benefits derived from traction is unknown and needs to be determined so that physiotherapists can provide better and more effective treatments. OBJECTIVE: This study analyzed the relationship between load magnitude and time during spinal traction in relation to stature variations. Traction effect duration was also analyzed. METHOD: Fifteen healthy male subjects (23.1 ± 5.77 years; 1.80 ± 0.17 m and 87.0 ± 9.6 kg were assessed under three traction conditions (0, 30 and 60% of body weight, BW of 42 minutes. Stature variation was used to determine intervertebral disc height variation. Stature was assessed every 7 minutes during traction of 42 minutes and every 5 minutes for 45 minutes after traction ceased. RESULTS: 0 and 30% BW traction produced similar gains (6.09 ± 1.89 mm, 5.70 ± 1.88 mm, respectively; p>0.05, while these were smaller (pCONTEXTUALIZAÇÃO: A tração sobre a coluna vertebral é um procedimento relativamente popular para aumentar o espaço inter-vertebral pela aplicação de forças de separação. Os parâmetros de tempo e magnitude da força aplicada podem influenciar os resultados desse procedimento e ainda precisam ser investigados. A duração dos benefícios derivados da tração não é conhecida e precisa ser determinada para que fisioterapeutas possam prover tratamentos melhores e mais eficientes. OBJETIVO: Este estudo analisou a relação entre a magnitude de carga e de tempo durante a tração vertebral sobre as variações de estatura, bem como a duração deste efeito. MÉTODOS: Quinze sujeitos saudáveis do sexo masculino (23,1 ± 5,77 anos; 1,80 ± 0,17 m e 87,0 ± 9,6 Kg foram mensurados sob três condições (0, 30 e 60% PC

  20. Gas cooled traction drive inverter

    Science.gov (United States)

    Chinthavali, Madhu Sudhan

    2013-10-08

    The present invention provides a modular circuit card configuration for distributing heat among a plurality of circuit cards. Each circuit card includes a housing adapted to dissipate heat in response to gas flow over the housing. In one aspect, a gas-cooled inverter includes a plurality of inverter circuit cards, and a plurality of circuit card housings, each of which encloses one of the plurality of inverter cards.