Highly enriched uranium (HEU) storage and disposition program plan

International Nuclear Information System (INIS)

Arms, W.M.; Everitt, D.A.; O'Dell, C.L.

1995-01-01

Recent changes in international relations and other changes in national priorities have profoundly affected the management of weapons-usable fissile materials within the United States (US). The nuclear weapon stockpile reductions agreed to by the US and Russia have reduced the national security requirements for these fissile materials. National policies outlined by the US President seek to prevent the accumulation of nuclear weapon stockpiles of plutonium (Pu) and HEU, and to ensure that these materials are subjected to the highest standards of safety, security and international accountability. The purpose of the Highly Enriched Uranium (HEU) Storage and Disposition Program Plan is to define and establish a planned approach for storage of all HEU and disposition of surplus HEU in support of the US Department of Energy (DOE) Fissile Material Disposition Program. Elements Of this Plan, which are specific to HEU storage and disposition, include program requirements, roles and responsibilities, program activities (action plans), milestone schedules, and deliverables

The MARVEL assembly for neutron multiplication

Energy Technology Data Exchange (ETDEWEB)

David L. Chichester; Mathew T. Kinlaw

2013-10-01

A new multiplying test assembly is under development at Idaho National Laboratory to support research, validation, evaluation, and learning. The item is comprised of three stacked, highly-enriched uranium (HEU) cylinders, each 11.4 cm in diameter and having a combined height of up to 11.7 cm. The combined mass of all three cylinders is 20.3 kg of HEU. Calculations for the bare configuration of the assembly indicate a multiplication level of >3.5 (keff=0.72). Reflected configurations of the assembly, using either polyethylene or tungsten, are possible and have the capability of raising the assembly's multiplication level to greater than 10. This paper describes simulations performed to assess the assembly's multiplication level under different conditions and describes the resources available at INL to support the use of these materials. We also describe some preliminary calculations and test activities using the assembly to study neutron multiplication.

The MARVEL assembly for neutron multiplication.

Science.gov (United States)

Chichester, David L; Kinlaw, Mathew T

2013-10-01

A new multiplying test assembly is under development at Idaho National Laboratory to support research, validation, evaluation, and learning. The item is comprised of three stacked, highly-enriched uranium (HEU) cylinders, each 11.4 cm in diameter and having a combined height of up to 11.7 cm. The combined mass of all three cylinders is 20.3 kg of HEU. Calculations for the bare configuration of the assembly indicate a multiplication level of >3.5 (k(eff)=0.72). Reflected configurations of the assembly, using either polyethylene or tungsten, are possible and have the capability of raising the assembly's multiplication level to greater than 10. This paper describes simulations performed to assess the assembly's multiplication level under different conditions and describes the resources available at INL to support the use of these materials. We also describe some preliminary calculations and test activities using the assembly to study neutron multiplication. Copyright © 2013 Elsevier Ltd. All rights reserved.

Application of international safeguards to fast critical assembly facilities. FY 1980 summary report

International Nuclear Information System (INIS)

1980-12-01

Nuclear materials inventory-verification techniques for large split-table fast critical assemblies are being studied in this program. Emphasis has been given to techniques that minimize fuel handling in order to reduce facility downtime and radiation exposure to the inventory team. The techniques studied include drawer seals, autoradiography, and spectral index measurements. Two-drawer sealing techniques have been studied, and the relative strengths and weaknesses are pointed out. The rod-type locking mechanism would not disrupt the reactor cooling air flow or interfere with autoradiography but is more expensive to implement. Passive autoradiography was used in a ZPPR inventory to verify to a 93% confidence level that less than 8-kg Pu was missing. The inventory was completed in four days by a five-member team with radiation exposures well within acceptable limits. Two autoradiographic film packages were developed to distinguish HEU from a DU matrix. The 30-mil pack requires an exposure between 4 and 16 hours and fits into most of the drawers. The 40-mil pack requires only a two-hour exposure but fits into less than half the drawers

Supply of low enriched (LEU) and highly enriched uranium (HEU) for research reactors

International Nuclear Information System (INIS)

Mueller, H.

1997-01-01

Enriched uranium for research reactors in the form of LEU /= low enriched uranium at 19.75% U-235) and HEU (= highly enriched uranium at 90 to 93% U-235) was and is - due to its high U-235 enrichment - a political fuel other than enriched uranium for power reactors. The sufficient availability of LEU and HEU is a vital question for research reactors, especially in Europe, in order to perform their peaceful research reactor programs. In the past the USA were in the Western hemisphere sole supplier of LEU and HEU. Today the USA have de facto stopped the supply of LEU and HEU, for HEU mainly due to political reasons. This paper deals, among others, with the present availability of LEU and HEU for European research reactors and touches the following topics: - historical US supplies, - influence of the RERTR-program, - characteristics of LEU and HEU, - military HEU enters the civil market, -what is the supply situation for LEU and HEU today? - outlook for safe supplies of LEU and HEU. (author)

2009 Annual Health Physics Report for the HEU Transparency Program

International Nuclear Information System (INIS)

Radev, R.

2010-01-01

During the 2009 calendar year, Lawrence Livermore National Laboratory (LLNL) provided health physics support for the Highly Enriched Uranium (HEU) Transparency Program for external and internal radiation protection. LLNL also provided technical expertise related to BDMS radioactive sources and Russian radiation safety regulatory compliance. For the calendar year 2009, there were 159 person-trips that required dose monitoring of the U.S. monitors. Of the 159 person-trips, 149 person-trips were SMVs and 10 person-trips were Transparency Monitoring Office (TMO) trips. There were 4 monitoring visits by TMO monitors to facilities other than UEIE and 10 to UEIE itself. LLNL's Hazard Control Department laboratories provided the dosimetry services for the HEU Transparency monitors. In 2009, the HEU Transparency activities in Russia were conducted in a radiologically safe manner for the HEU Transparency monitors in accordance with the expectations of the HEU Transparency staff, NNSA and DOE. The HEU Transparency Program now has over fifteen years of successful experience in developing and providing health and safety support in meeting its technical objectives.

Reflector-moderated critical assemblies

International Nuclear Information System (INIS)

Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

1975-07-01

Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

2011 Annual Health Physics Report for the HEU transparency Program

International Nuclear Information System (INIS)

Radev, R.

2012-01-01

During the 2008 calendar year, Lawrence Livermore National Laboratory (LLNL) provided health physics support for the Highly Enriched Uranium (HEU) Transparency Program for external and internal radiation protection. They also provided technical expertise related to BDMS radioactive sources and Russian radiation safety regulatory compliance. For the calendar year 2008, there were 158 person-trips that required dose monitoring of the U.S. monitors. Of the 158 person-trips, 148 person-trips were SMVs and 10 person-trips were Transparency Monitoring Office (TMO) trips. There were 6 monitoring visits by TMO monitors to facilities other than UEIE and 8 to UEIE itself. There were three monitoring visits (source changes) that were back-to-back with a total of 24 monitors. LLNL's Hazard Control Department laboratories provided the dosimetry services for the HEU Transparency monitors. In 2008, the HEU Transparency activities in Russia were conducted in a radiologically safe manner for the HEU Transparency monitors in accordance with the expectations of the HEU Transparency staff, NNSA and DOE. The HEU Transparency now has thirteen years of successful experience in developing and providing health and safety support in meeting its technical objectives.

Fast critical assembly safeguards: NDA methods for highly enriched uranium. Summary report, October 1978-September 1979

International Nuclear Information System (INIS)

Bellinger, F.O.; Winslow, G.H.

1980-12-01

Nondestructive assay (NDA) methods, principally passive gamma measurements and active neutron interrogation, have been studied for their safeguards effectiveness and programmatic impact as tools for making inventories of highly enriched uranium fast critical assembly fuel plates. It was concluded that no NDA method is the sole answer to the safeguards problem, that each of those emphasized here has its place in an integrated safeguards system, and that each has minimum facility impact. It was found that the 185-keV area, as determined with a NaI detector, was independent of highly-enriched uranium (HEU) plate irradiation history, though the random neutron driver methods used here did not permit accurate assay of irradiated plates. Containment procedures most effective for accurate assaying were considered, and a particular geometry is recommended for active interrogation by a random driver. A model, pertinent to that geometry, which relates the effects of multiplication and self-absorption, is described. Probabilities of failing to detect that plates are missing are examined

ENDF/B-VII.1 Neutron Cross Section Data Testing with Critical Assembly Benchmarks and Reactor Experiments

Energy Technology Data Exchange (ETDEWEB)

Kahler, A.C.; Herman, M.; Kahler,A.C.; MacFarlane,R.E.; Mosteller,R.D.; Kiedrowski,B.C.; Frankle,S.C.; Chadwick,M.B.; McKnight,R.D.; Lell,R.M.; Palmiotti,G.; Hiruta,H.; Herman,M.; Arcilla,R.; Mughabghab,S.F.; Sublet,J.C.; Trkov,A.; Trumbull,T.H.; Dunn,M.

2011-12-01

The ENDF/B-VII.1 library is the latest revision to the United States Evaluated Nuclear Data File (ENDF). The ENDF library is currently in its seventh generation, with ENDF/B-VII.0 being released in 2006. This revision expands upon that library, including the addition of new evaluated files (was 393 neutron files previously, now 423 including replacement of elemental vanadium and zinc evaluations with isotopic evaluations) and extension or updating of many existing neutron data files. Complete details are provided in the companion paper [M. B. Chadwick et al., 'ENDF/B-VII.1 Nuclear Data for Science and Technology: Cross Sections, Covariances, Fission Product Yields and Decay Data,' Nuclear Data Sheets, 112, 2887 (2011)]. This paper focuses on how accurately application libraries may be expected to perform in criticality calculations with these data. Continuous energy cross section libraries, suitable for use with the MCNP Monte Carlo transport code, have been generated and applied to a suite of nearly one thousand critical benchmark assemblies defined in the International Criticality Safety Benchmark Evaluation Project's International Handbook of Evaluated Criticality Safety Benchmark Experiments. This suite covers uranium and plutonium fuel systems in a variety of forms such as metallic, oxide or solution, and under a variety of spectral conditions, including unmoderated (i.e., bare), metal reflected and water or other light element reflected. Assembly eigenvalues that were accurately predicted with ENDF/B-VII.0 cross sections such as unmoderated and uranium reflected {sup 235}U and {sup 239}Pu assemblies, HEU solution systems and LEU oxide lattice systems that mimic commercial PWR configurations continue to be accurately calculated with ENDF/B-VII.1 cross sections, and deficiencies in predicted eigenvalues for assemblies containing selected materials, including titanium, manganese, cadmium and tungsten are greatly reduced. Improvements are also

Time-correlated neutron analysis of a multiplying HEU source

Energy Technology Data Exchange (ETDEWEB)

Miller, E.C., E-mail: Eric.Miller@jhuapl.edu [Johns Hopkins University Applied Physics Laboratory, Laurel, MD (United States); Kalter, J.M.; Lavelle, C.M. [Johns Hopkins University Applied Physics Laboratory, Laurel, MD (United States); Watson, S.M.; Kinlaw, M.T.; Chichester, D.L. [Idaho National Laboratory, Idaho Falls, ID (United States); Noonan, W.A. [Johns Hopkins University Applied Physics Laboratory, Laurel, MD (United States)

2015-06-01

The ability to quickly identify and characterize special nuclear material remains a national security challenge. In counter-proliferation applications, identifying the neutron multiplication of a sample can be a good indication of the level of threat. Currently neutron multiplicity measurements are performed with moderated {sup 3}He proportional counters. These systems rely on the detection of thermalized neutrons, a process which obscures both energy and time information from the source. Fast neutron detectors, such as liquid scintillators, have the ability to detect events on nanosecond time scales, providing more information on the temporal structure of the arriving signal, and provide an alternative method for extracting information from the source. To explore this possibility, a series of measurements were performed on the Idaho National Laboratory's MARVEL assembly, a configurable HEU source. The source assembly was measured in a variety of different HEU configurations and with different reflectors, covering a range of neutron multiplications from 2 to 8. The data was collected with liquid scintillator detectors and digitized for offline analysis. A gap based approach for identifying the bursts of detected neutrons associated with the same fission chain was used. Using this approach, we are able to study various statistical properties of individual fission chains. One of these properties is the distribution of neutron arrival times within a given burst. We have observed two interesting empirical trends. First, this distribution exhibits a weak, but definite, dependence on source multiplication. Second, there are distinctive differences in the distribution depending on the presence and type of reflector. Both of these phenomena might prove to be useful when assessing an unknown source. The physical origins of these phenomena can be illuminated with help of MCNPX-PoliMi simulations.

Time-correlated neutron analysis of a multiplying HEU source

Science.gov (United States)

Miller, E. C.; Kalter, J. M.; Lavelle, C. M.; Watson, S. M.; Kinlaw, M. T.; Chichester, D. L.; Noonan, W. A.

2015-06-01

The ability to quickly identify and characterize special nuclear material remains a national security challenge. In counter-proliferation applications, identifying the neutron multiplication of a sample can be a good indication of the level of threat. Currently neutron multiplicity measurements are performed with moderated 3He proportional counters. These systems rely on the detection of thermalized neutrons, a process which obscures both energy and time information from the source. Fast neutron detectors, such as liquid scintillators, have the ability to detect events on nanosecond time scales, providing more information on the temporal structure of the arriving signal, and provide an alternative method for extracting information from the source. To explore this possibility, a series of measurements were performed on the Idaho National Laboratory's MARVEL assembly, a configurable HEU source. The source assembly was measured in a variety of different HEU configurations and with different reflectors, covering a range of neutron multiplications from 2 to 8. The data was collected with liquid scintillator detectors and digitized for offline analysis. A gap based approach for identifying the bursts of detected neutrons associated with the same fission chain was used. Using this approach, we are able to study various statistical properties of individual fission chains. One of these properties is the distribution of neutron arrival times within a given burst. We have observed two interesting empirical trends. First, this distribution exhibits a weak, but definite, dependence on source multiplication. Second, there are distinctive differences in the distribution depending on the presence and type of reflector. Both of these phenomena might prove to be useful when assessing an unknown source. The physical origins of these phenomena can be illuminated with help of MCNPX-PoliMi simulations.

Time-correlated neutron analysis of a multiplying HEU source

International Nuclear Information System (INIS)

Miller, E.C.; Kalter, J.M.; Lavelle, C.M.; Watson, S.M.; Kinlaw, M.T.; Chichester, D.L.; Noonan, W.A.

2015-01-01

The ability to quickly identify and characterize special nuclear material remains a national security challenge. In counter-proliferation applications, identifying the neutron multiplication of a sample can be a good indication of the level of threat. Currently neutron multiplicity measurements are performed with moderated 3 He proportional counters. These systems rely on the detection of thermalized neutrons, a process which obscures both energy and time information from the source. Fast neutron detectors, such as liquid scintillators, have the ability to detect events on nanosecond time scales, providing more information on the temporal structure of the arriving signal, and provide an alternative method for extracting information from the source. To explore this possibility, a series of measurements were performed on the Idaho National Laboratory's MARVEL assembly, a configurable HEU source. The source assembly was measured in a variety of different HEU configurations and with different reflectors, covering a range of neutron multiplications from 2 to 8. The data was collected with liquid scintillator detectors and digitized for offline analysis. A gap based approach for identifying the bursts of detected neutrons associated with the same fission chain was used. Using this approach, we are able to study various statistical properties of individual fission chains. One of these properties is the distribution of neutron arrival times within a given burst. We have observed two interesting empirical trends. First, this distribution exhibits a weak, but definite, dependence on source multiplication. Second, there are distinctive differences in the distribution depending on the presence and type of reflector. Both of these phenomena might prove to be useful when assessing an unknown source. The physical origins of these phenomena can be illuminated with help of MCNPX-PoliMi simulations

Heat-transfer analysis of the existing HEU and proposed LEU cores of Pakistan research reactor

International Nuclear Information System (INIS)

Khan, L.A.; Nabbi, R.

1987-02-01

In connection with conversion of Pakistan Research Reactor (PARR) from the use of Highly Enriched Uranium (HEU) fuel to the use of Low Enriched Uranium (LEU) fuel, steady-state thermal hydraulic analysis of both existing HEU and proposed LEU cores has been carried out. Keeping in mind the possibility of power upgrading, the performance of proposed LEU core, under 10 MW operating conditions, has also been evaluated. Computer code HEATHYD has been used for this purpose. In order to verify the reliability of the code, IAEA benchmark 2 MW reactor was analyzed. The cooling parameters evaluated include: coolant velocity, critical velocity, pressure drop, temperature distribution in the core, heat fluxes at onset of nucleate boiling, flow instability and burnout and corresponding safety margins. From the results of the study it can be concluded that the conversion of the core to LEU fuel will result in higher safety margins, as compared to existing HEU core, mainly because the increased number of fuel plates in the proposed design will reduce the average heat flux significantly. Anyhow upgrading of the reactor power to 10 MW will need the flow rate to be adjusted between 850 to 900 m 3 /hr, to achieve reasonable safety margins, at least, comparable with the existing HEU core. (orig.)

The National Criticality Experiments Research Center at the Device Assembly Facility, Nevada National Security Site: Status and Capabilities, Summary Report

International Nuclear Information System (INIS)

Bragg-Sitton, S.; Bess, J.; Werner, J.

2011-01-01

The National Criticality Experiments Research Center (NCERC) was officially opened on August 29, 2011. Located within the Device Assembly Facility (DAF) at the Nevada National Security Site (NNSS), the NCERC has become a consolidation facility within the United States for critical configuration testing, particularly those involving highly enriched uranium (HEU). The DAF is a Department of Energy (DOE) owned facility that is operated by the National Nuclear Security Agency/Nevada Site Office (NNSA/NSO). User laboratories include the Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL). Personnel bring their home lab qualifications and procedures with them to the DAF, such that non-site specific training need not be repeated to conduct work at DAF. The NNSS Management and Operating contractor is National Security Technologies, LLC (NSTec) and the NNSS Safeguards and Security contractor is Wackenhut Services. The complete report provides an overview and status of the available laboratories and test bays at NCERC, available test materials and test support configurations, and test requirements and limitations for performing sub-critical and critical tests. The current summary provides a brief summary of the facility status and the method by which experiments may be introduced to NCERC.

HEU Measurements of Holdup and Recovered Residue in the Deactivation and Decommissioning Activities of the 321-M Reactor Fuel Fabrication Facility at the Savannah River Site

Energy Technology Data Exchange (ETDEWEB)

DEWBERRY, RAYMOND; SALAYMEH, SALEEM R.; CASELLA, VITO R.; MOORE, FRANK S.

2005-03-11

This paper contains a summary of the holdup and material control and accountability (MC&A) assays conducted for the determination of highly enriched uranium (HEU) in the deactivation and decommissioning (D&D) of Building 321-M at the Savannah River Site (SRS). The 321-M facility was the Reactor Fuel Fabrication Facility at SRS and was used to fabricate HEU fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the SRS production reactors. The facility operated for more than 35 years. During this time thousands of uranium-aluminum-alloy (U-Al) production reactor fuel tubes were produced. After the facility ceased operations in 1995, all of the easily accessible U-Al was removed from the building, and only residual amounts remained. The bulk of this residue was located in the equipment that generated and handled small U-Al particles and in the exhaust systems for this equipment (e.g., Chip compactor, casting furnaces, log saw, lathes A & B, cyclone separator, Freon{trademark} cart, riser crusher, ...etc). The D&D project is likely to represent an important example for D&D activities across SRS and across the Department of Energy weapons complex. The Savannah River National Laboratory was tasked to conduct holdup assays to quantify the amount of HEU on all components removed from the facility prior to placing in solid waste containers. The U-235 holdup in any single component of process equipment must not exceed 50 g in order to meet the container limit. This limit was imposed to meet criticality requirements of the low level solid waste storage vaults. Thus the holdup measurements were used as guidance to determine if further decontamination of equipment was needed to ensure that the quantity of U-235 did not exceed the 50 g limit and to ensure that the waste met the Waste Acceptance Criteria (WAC) of the solid waste storage vaults. Since HEU is an accountable nuclear material, the holdup assays and assays of recovered

Fuel conversion of JRR-4 from HEU to LEU

International Nuclear Information System (INIS)

Ichikawa, Hiroki; Nakajima, Teruo

1997-01-01

Japanese JRR-4 (Japan Research Reactor No.4) is a pool type, light water moderated and cooled, ETR type fuel reactor used for Shielding experiments, isotope production, neutron activation analyses, Si doping, reactor students training. It acieved first criticality on January 28, 1965 with maximum thermal power 3.5MW. The standard core consistes of 20 Fuel elements, 7 control rods 5 Irradiation holes, neutron source, graphite reflectors. Available thermal flux is 7x1013 n/cm2/s. Within the RERTR program plans are made for core conversion from HEU to LEU

Dynamical analysis of critical assembly CC-1

International Nuclear Information System (INIS)

Aleman Fernandez, J.R.

1990-01-01

The computer code CC-1, elaborated for the analysis of transients in Critical Assemblies is described. The results by the program are compared with the ones presented in the Safety Report for the Critical Assembly of ''La Quebrada'' Nuclear Research Centre (CIN). 7 refs

ZPPR-20 phase D : a cylindrical assembly of polyethylene moderated U metal reflected by beryllium oxide and polyethylene.

Energy Technology Data Exchange (ETDEWEB)

Lell, R.; Grimm, K.; McKnight, R.; Shaefer, R.; Nuclear Engineering Division; INL

2006-09-30

The Zero Power Physics Reactor (ZPPR) fast critical facility was built at the Argonne National Laboratory-West (ANL-W) site in Idaho in 1969 to obtain neutron physics information necessary for the design of fast breeder reactors. The ZPPR-20D Benchmark Assembly was part of a series of cores built in Assembly 20 (References 1 through 3) of the ZPPR facility to provide data for developing a nuclear power source for space applications (SP-100). The assemblies were beryllium oxide reflected and had core fuel compositions containing enriched uranium fuel, niobium and rhenium. ZPPR-20 Phase C (HEU-MET-FAST-075) was built as the reference flight configuration. Two other configurations, Phases D and E, simulated accident scenarios. Phase D modeled the water immersion scenario during a launch accident, and Phase E (SUB-HEU-MET-FAST-001) modeled the earth burial scenario during a launch accident. Two configurations were recorded for the simulated water immersion accident scenario (Phase D); the critical configuration, documented here, and the subcritical configuration (SUB-HEU-MET-MIXED-001). Experiments in Assembly 20 Phases 20A through 20F were performed in 1988. The reference water immersion configuration for the ZPPR-20D assembly was obtained as reactor loading 129 on October 7, 1988 with a fissile mass of 167.477 kg and a reactivity of -4.626 {+-} 0.044{cents} (k {approx} 0.9997). The SP-100 core was to be constructed of highly enriched uranium nitride, niobium, rhenium and depleted lithium. The core design called for two enrichment zones with niobium-1% zirconium alloy fuel cladding and core structure. Rhenium was to be used as a fuel pin liner to provide shut down in the event of water immersion and flooding. The core coolant was to be depleted lithium metal ({sup 7}Li). The core was to be surrounded radially with a niobium reactor vessel and bypass which would carry the lithium coolant to the forward inlet plenum. Immediately inside the reactor vessel was a rhenium

Fuel cycle cost study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1984-01-01

Fuel cycle costs are compared for a range of 235 U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors

Transition from HEU to LEU fuel in Romania's 14-MW TRIGA reactor

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.

1995-01-01

The 14-MW TRIGA steady state reactor (SSR) located in Pitesti, Romania, first went critical in the fall of 1979. Initially, the core configuration for full power operation used 29 fuel clusters each containing a 5 x 5 square array of HEU U (10 wt% - ZrH - Er 2.8 wt%) fuel-moderator rods (1.295 cm o.d.) clad in Incoloy. With a total inventory of 35 HEU fuel clusters, burnup, considerations required a gradual expansion of the core from 29 to 32 and finally to 35 clusters before the reactor was shut down because of insufficient excess reactivity. At this time each of the original 29 fuel clusters had an average 235 U burnup in the range from 50 to 62%. Because of the U.S. policy regarding the export of highly enriched uranium, fresh HEU TRIGA replacement fuel is not available. After a number of safety-related measurements, the SSR is expected to resume full power operation in the near future using a mixed core containing five LEU TRIGA clusters of the same geometry as the original fuel but with fuel-moderator rods containing 45 wt% U (19.7% 235 U enrichment) and 1.1 wt% Er. Rods for 14 additional LEU fuel clusters will be fabricated by General Atomics. In support of the SSR mixed core operation numerous neutronic calculations have been performed. This paper presents some of the results of those calculations. (author)

RERTR end-game: A win-win framework. Phasing out remaining global HEU commerce by conditionally and temporarily renewing U.S. exports of HEU

International Nuclear Information System (INIS)

Kuperman, Alan J.; Leventhal, Paul L.

1997-01-01

The RERTR program stands on the brink of fulfilling its historic mission. However, a series of missteps and misunderstandings have recently raised the risk that defeat will be snatched from the jaws of victory. Perhaps the most serious threat to the RERTR regime is posed by France's pending import of 625 kilograms of bomb-grade, highly enriched uranium (HEU) from Russia, intended primarily to fuel its high-flux research reactor at the Institute Laue-Langevin in Grenoble, as well as its Orphee research reactor. As the first export of HEU from Russia to a facility outside the former Soviet bloc, this precedential transaction would establish Russia as a new global supplier of bomb-grade uranium, potentially setting the stage for a rise in international HEU commerce, rather than its phase-out as envisioned under the RERTR program. Apparently, France turned to Russia for supply of the fuel because the United States was perceived as unable or unwilling to continue supplying such fuel in the wake of the U.S. Energy Policy Act of 1992, which, pursuant to its so-called Schumer Amendment, places sharp restrictions on HEU exports. Unexplained delays in Russia's shipment of this material to France provide a fortuitous window of opportunity in which efforts can and should be made by France and the United States to resolve present differences in a manner beneficial to each, as well as in the interest of global security. This paper proposes an arrangement under which the United States would renew exports of HEU to France, in exchange for pledges from France enabling the export to comply with the principles and objectives of the RERTR program as embodied in U.S. law. In so doing, the arrangement would obviate the need for Russian HEU export, thereby avoiding its dangerous precedent. By enabling high quality scientific research to continue, while simultaneously helping to fulfill the RERTR program's original goal, such an arrangement would truly be a 'win-win' solution. (author)

Feasibility study for LEU conversion of the WWR-K reactor at the Institute of Nuclear Physics in Kazakhstan using a 5-tube fuel assembly

International Nuclear Information System (INIS)

Hanan, N.A.; Liaw, J.R.; Matos, J.E.

2005-01-01

A feasibility study by the RERTR program for possible LEU conversion of the 6 MW WWR-K reactor concludes that conversion is feasible using an LEU 5-tube Russian fuel assembly design. This 5-tube design is one of several LEU fuel assembly designs being studied (Ref. 1) for possible use in this reactor. The 5-tube assembly contains 200 g 235 U with an enrichment of 19.7% in four cylindrical inner tubes and an outer hexagonal tube with the same external dimensions as the current HEU (36%) 5-tube fuel assembly, which contains 112.5 g 235 U. The fuel meat material, LEU UO 2 -Al dispersion fuel with ∼ 2.5 g U/cm 3 , has been extensively irradiation tested in a number of reactors with uranium enrichments of 36% and 19.7%. Since the 235 U loading of the LEU assemblies is much larger than the HEU assemblies, a smaller LEU core with five rows of fuel assemblies is possible (instead of six rows of fuel assemblies in the HEU core). This smaller LEU core would consume about 60% as many fuel assemblies per year as the current HEU core and provide thermal neutron fluxes in the inner irradiation channels that are ∼ 17% larger than with the present HEU core. The current 21 day cycle length would be maintained and the average discharge burnup would be ∼ 42%. Neutron fluxes in the five outer irradiation channels would be smaller in the LEU core unless these channels can be moved closer to the LEU fuel assemblies. Results show that the smaller LEU core would meet the reactor's shutdown margin requirements and would have an adequate thermal-hydraulic safety margin to onset of nucleate boiling. (author)

Development of a New Multiplying Assembly for Research, Validation, Evaluation, and Learning

Energy Technology Data Exchange (ETDEWEB)

David L. Chichester

2012-10-01

A new multiplying test assembly is under development at Idaho National Laboratory (INL) to support research, validation, evaluation, and learning. The item is comprised of two stacked highly-enriched uranium (HEU) cylinders each 11.4 cm in diameter and having a combined height of 8.4 cm. The combined mass is 14.4 kg of HEU. Calculations for the bare configuration of the assembly indicate a multiplication level of >2.5 (keff = 0.62). Reflected configurations of the assembly, using either polyethylene or tungsten, are possible and have the capability of raising its multiplication level to approximately 8. This paper will describe the MCNP calculations performed to assess the assembly's multiplication level under different conditions and describe the resource available at INL to support visiting researchers in their use of the material. We will also describe some preliminary calculations and test activities using the assembly to study neutron multiplicity.

A simple method for rapidly processing HEU from weapons returns

Energy Technology Data Exchange (ETDEWEB)

McLean, W. II; Miller, P.E.

1994-01-01

A method based on the use of a high temperature fluidized bed for rapidly oxidizing, homogenizing and down-blending Highly Enriched Uranium (HEU) from dismantled nuclear weapons is presented. This technology directly addresses many of the most important issues that inhibit progress in international commerce in HEU; viz., transaction verification, materials accountability, transportation and environmental safety. The equipment used to carry out the oxidation and blending is simple, inexpensive and highly portable. Mobile facilities to be used for point-of-sale blending and analysis of the product material are presented along with a phased implementation plan that addresses the conversion of HEU derived from domestic weapons and related waste streams as well as material from possible foreign sources such as South Africa or the former Soviet Union.

Tungsten--carbide critical assembly

International Nuclear Information System (INIS)

Hansen, G.E.; Paxton, H.C.

1975-06-01

The tungsten--carbide critical assembly mainly consists of three close-fitting spherical shells: a highly enriched uranium shell on the inside, a tungsten--carbide shell surrounding it, and a steel shell on the outside. Ideal critical specifications indicate a rather low computed value of k/sub eff/. Observed and calculated fission-rate distributions for 235 U, 238 U, and 237 Np are compared, and calculated leakage neutrons per fission in various energy groups are given. (U.S.)

A fuel cycle cost study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1985-01-01

Fuel cycle costs are compared for a range of 235 U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors. (author)

A fuel cycle cost study with HEU and LEU fuels

Energy Technology Data Exchange (ETDEWEB)

Matos, J E; Freese, K E [Argonne National Laboratory, Argonne, IL (United States)

1985-07-01

Fuel cycle costs are compared for a range of {sup 235}U loadings with HEU and LEU fuels using the IAEA generic 10 MW reactor as an example. If LEU silicide fuels are successfully demonstrated and licensed, the results indicate that total fuel cycle costs can be about the same or lower than those with the HEU fuels that are currently used in most research reactors. (author)

Criticality Analysis of SAMOP Subcritical Assembly

International Nuclear Information System (INIS)

Tegas-Sutondo; Syarip; Triwulan-Tjiptono

2005-01-01

A critically analysis has been performed for homogenous system of uranyl nitrate solution, as part of a preliminary design assessment on neutronic aspect of SAMOP sub-critical assembly. The analysis is intended to determine some critical parameters such as the minimum of critical dimension and critical mass for the desired concentration. As the basis of this analysis, it has been defined a fuel system with an enrichment of 20% for cylindrical geometry of both bare and graphite reflected of 30 cm thickness. The MCNP code has been utilized for this purpose, for variation of concentrations ranging from 150 g/l to 500 g/l. It is found that the best concentration giving the minimum geometrical dimension is around 400 g/l, for both the bare and reflected systems. Whilst the best one, of minimum critical mass is corresponding to the concentration of around 200 g/l with critical mass around 14.1 kg and 4.2 kg for the bare and reflected systems respectively. Based on the result of calculations, it is concluded that by taking into consideration of the critical limit, the SAMOP subcritical assembly is neutronically can be made. (author)

Criticality calculations for a critical assembly, graphite moderate, using 20% enriched uranium

International Nuclear Information System (INIS)

Almeida Ferreira, A.C. de; Hukai, R.Y.

1975-01-01

The construction of a Zero Power Reactor (ZPR) at the Instituto de Energia Atomica in order to measure the neutron characteristics (parameters) of HTGR reactors is proposed. The necessary quantity fissile uranium for these measurements has been calculed. Criticality studies of graphite moderated critical assemblies containing thorium have been made and the critical mass of each of several typical commercial HTGR compositions has been calculated using computer codes HAMMER and CITATION. Assemblies investigated contained a central cylindrical core region, simulating a typical commercial HTGR composition, a uranium-graphite driver region and a outer pure graphite reflector region. It is concluded that a 10Kg inventory of fissile uranium will be required for a program of measurements utilizing each of the several calculated assemblies

Los Alamos Critical Assemblies Facility

International Nuclear Information System (INIS)

Malenfant, R.E.

1981-06-01

The Critical Assemblies Facility of the Los Alamos National Laboratory has been in existence for thirty-five years. In that period, many thousands of measurements have been made on assemblies of 235 U, 233 U, and 239 Pu in various configurations, including the nitrate, sulfate, fluoride, carbide, and oxide chemical compositions and the solid, liquid, and gaseous states. The present complex of eleven operating machines is described, and typical applications are presented

Implementation of the United States/Russian HEU Agreement: Current Status and Prospects

International Nuclear Information System (INIS)

Rutkowski, E

2003-01-01

During Calendar Year (CY) 2002, the Russian Federation (R.F.) delivered low enriched uranium (LEU) from the conversion and processing of 30 metric tons (MT) of weapons-grade (90% 235 U assay) uranium. Through July 2003, the Highly Enriched Uranium (HEU) Transparency Implementation Program (TIP) will have monitored the conversion of over 190 MT HEU into LEU. This total represents about 38 percent of the projected 500 MT HEU scheduled to be blended down through the year 2013 and is equivalent to the destruction of 7,600 nuclear devices. The National Nuclear Security Administration's (NNSA) HEU-TIP monitors the processing of this HEU at four Russian uranium-processing plants. During CY 2002, United States (U.S.) personnel monitored this process for a total of 194 monitor-weeks by staffing a Transparency Monitoring Office (TMO) located in Novouralsk, and through a series of five-day Special Monitoring Visits (SMV) to the four plants. U.S. monitor observations include the inventory of in-process containers, the observation of operations and non-destructive assay measurements (NDA) to determine 235 U enrichment, as well as the examination and validation of Russian Material Control and Accountability (MC and A) documents. In addition, the U.S. designed Blend Down Monitoring System (BDMS) installed at the Ural Electrochemical Integrated Plant (UEIP) in January 1999 monitored all HEU blended at that facility, which is about 50 percent of the HEU blended into LEU during CY 2002. Recently we installed a BDMS at the Electrochemical Plant (ECP) in Zelenogorsk and plans are underway to install a BDMS at the Siberian Chemical Enterprise (SChE) in Seversk in late 2004. On a very positive note, interpersonal interactions between U.S. and Russian technical experts continues to expand and have proven to be an important element of the transparency regime. On the tenth anniversary of the HEU Purchase Agreement, the Ministry of the R.F. for Atomic Energy (Minatom) also saluted the

A level-playing field for medical isotope production - How to phase-out reliance on HEU

International Nuclear Information System (INIS)

Kuperman, A.J.

1999-01-01

Two decades ago, civilian commerce in highly enriched uranium (HEU) for use as targets in the production of medical isotopes was considered a relatively minor security concern for three reasons. First, the number of producers was small. Second, the amount of HEU involved was small. Third, the amount of HEU was dwarfed by the quantities of HEU in civilian commerce as fuel for nuclear research and test reactors. Now, however, all three variables have changed. First, as the use of medical isotopes has expanded rapidly, production programs are proliferating. Second, as the result of such new producers and the expansion of existing production facilities, the amounts of HEU involved are growing. Third, as the RERTR program has facilitated the phase-out of HEU as fuel in most research and test reactors, the quantities of HEU for isotope production have come to represent a significant percentage of global commerce in this weapons-usable material. Medical isotope producers in several states are cooperating with the RERTR program to convert to low-enriched uranium (LEU) targets within the next few years, and one already relies on LEU for isotope production. However, the three biggest isotope producers - in Canada and the European Union - continue to rely on HEU, creating a double-standard that endangers the goal of the RERTR program. Each of these three producers has expressed economic concerns about being put at a competitive disadvantage if it alone converts. This paper proposes forging a firmer international consensus that all present and future isotope producers should convert to LEU, and calls for codifying such a commitment in a statement of intent to be prepared by producers over the next year. With such a level playing field, no producer would need fear being put at a competitive disadvantage by conversion, or being stigmatized by pressure groups for continued reliance on HEU. The phase-out of all HEU commerce for isotope production could be achieved within about

Radiological consequence analysis with HEU and LEU fuels

Energy Technology Data Exchange (ETDEWEB)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1984-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and non-site specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. 10 references, 3 figures, 7 tables.

Radiological consequence analysis with HEU and LEU fuels

International Nuclear Information System (INIS)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1984-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and non-site specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. 10 references, 3 figures, 7 tables

LEU WWR-M2 fuel assemblies burnable test

International Nuclear Information System (INIS)

Kirsanov, G.A.; Konoplev, K.A.; Pikulik, R.G.; Sajkov, Yu. P.; Tchmshkyan, D.V.; Tedoradze, L.V.; Zakharov, A.S.

2000-01-01

The results of in-pile irradiation tests of LEU WWR-M2 fuel assemblies with reduced enrichment of fuel are submitted in the report. The tests are made according to the Russian Program on Reduced Enrichment for Research and Test Reactors (RERTR). United States Department of Energy and the Ministry of Atomic Energy of Russian Federation jointly fund this Program. The irradiation tests of 5 WWR-M2 experimental assemblies are carried out at WWR-M reactor of the Petersburg Nuclear Physics Institute (PNPI). The information on assembly design and technique of irradiation tests is presented. In the irradiation tests the integrity of fuel assemblies is periodically measured. The report presents the data for the integrity maintained during the burnup of 5 fuel assemblies up to 45%. These results demonstrate the high reliability of the experimental fuel assemblies within the guaranteed burnup limits specified by the manufacturer. The tests are still in progress; it is planned to test and analyze the change in integrity for burnup of up to 70% - 75% or more. LEU WWR-M2 fuel assemblies are to be offered for export by their Novosibirsk manufacturer. Currently, HEU WWR-M2 fuel assemblies are used in Hungary, Ukraine and Vietnam. LEU WWR-M2 fuel assemblies were designed as a possible replacement for the HEU WWR-M2 fuel assemblies in those countries, but their use can be extended to other research reactors. (author)

Stationary and protable instruments for assay of HEU [highly enriched uranium] solids holdup

International Nuclear Information System (INIS)

Russo, P.A.; Sprinkle, J.K. Jr.; Stephens, M.M.; Brumfield, T.L.; Gunn, C.S.; Watson, D.R.

1987-01-01

Two NaI(Tl)-based instruments, one stationary and one portable, designed for automated assay of highly enriched uranium (HEU) solids holdup, are being evaluated at the scrap recovery facility of the Oak Ridge Y-12 Plant. The stationary instrument, a continuous monitor of HEU within the filters of the chip burner exhaust system, measures the HEU deposits that accumulate erratically and rapidly during chip burner operation. The portable system was built to assay HEU in over 100 m of elevated piping used to transfer UO 3 , UO 2 , and UF 4 powder to, from, and between the fluid bed conversion furnances and the powder storage hoods. Both instruments use two detector heads. Both provide immediate automatic readout of accumulated HEU mass. The 186-keV 235 U gamma ray is the assay signature, and the 60-keV gamma ray from an 241 Am source attached to each detector is used to normalize the 186-keV rate. The measurement geometries were selected for compatibility with simple calibration models. The assay calibrations were calculated from these models and were verified and normalized with measurements of HEU standards built to match geometries of uniform accumulations on the surfaces of the process equipment. This instrumentation effort demonstrates that simple calibration models can often be applied to unique measurement geometries, minimizing the otherwise unreasonable requirements for calibration standards and allowing extension of the measurements to other process locations

Benchmark assemblies of the Los Alamos critical assemblies facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1986-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described. (author)

Benchmark assemblies of the Los Alamos Critical Assemblies Facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1985-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

Benchmark assemblies of the Los Alamos critical assemblies facility

International Nuclear Information System (INIS)

Dowdy, E.J.

1985-01-01

Several critical assemblies of precisely known materials composition and easily calculated and reproducible geometries have been constructed at the Los Alamos National Laboratory. Some of these machines, notably Jezebel, Flattop, Big Ten, and Godiva, have been used as benchmark assemblies for the comparison of the results of experimental measurements and computation of certain nuclear reaction parameters. These experiments are used to validate both the input nuclear data and the computational methods. The machines and the applications of these machines for integral nuclear data checks are described

31 CFR 540.305 - HEU Agreements.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false HEU Agreements. 540.305 Section 540.305 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF... Federation for Atomic Energy Concerning the Transfer of Source Material to the Russian Federation signed at...

Effects of low heterogeneity in fast critical assemblies

International Nuclear Information System (INIS)

Belov, S.P.; Dulin, V.A.; Zhukov, A.V.; Kuzin, E.N.; Mozhaev, V.K.; Sitnikov, V.I.; Tsibulya, A.M.; Shapar', A.V.; Zayfert, E.; Kuntsman, B.; Khayntsel'man, B.

1989-01-01

The problem of the low heterogeneity of fast critical assemblies, which are used to simulate fast reactors that are under design, has begun to assume increasing importance as the errors in nuclear data and group constants decrease and the capabilities of design codes improve. The design of the fuel channels of the fast critical assemblies of a BFS differs from that of the fuel subassemblies of a power reactor. The principal difference is that critical assemblies have a more heterogeneous structure than a reactor core does. As a result, the effects of this heterogeneity turn out to be appreciable for a number of functionals. Of particular interest was the measurement of the main neutronic characteristics of a fast reactor in its actual design and in the mockup produced by using BFS facilities. The authors measured and calculated the most important functionals (the ratios of the average cross sections of the main absorbing and fissioning elements, etc.) for both a homogeneous medium (fuel assemblies) and a heterogeneous medium (slugs, tubes) of practically identical composition. The objective of this work was to compare the discrepancy between experiment and calculations for the central functionals in the homogeneous and heterogeneous cases after corrections. This is a check of the accuracy of the simulation of homogeneous cores in fast power reactors by using the tools of the BFS fast critical assembly

HEU to LEU conversion experience at the UMass-Lowell research reactor

International Nuclear Information System (INIS)

White, John R.; Bobek, Leo M.

2005-01-01

The UMass-Lowell Research Reactor (UMLRR) operated safely with high-enriched uranium (HEU) fuel for over 25 years. Having reached the end of core lifetime and due to proliferation concerns, the reactor was recently converted to low-enriched uranium silicide (LEU) fuel. The actual process for converting the UMLRR from HEU to LEU fuel covered a period of over 15 years. The conversion effort - from the initial conceptual design studies in the late 1980s to the final offsite shipment of the spent HEU fuel in August 2004 - was a unique experience for the faculty and staff of a small university research reactor. This paper gives a historical view of the process and it highlights several key milestones along the road to successful completion of this project. (author)

A radiological consequence analysis with HEU and LEU fuels

International Nuclear Information System (INIS)

Woodruff, W.L.; Warinner, D.K.; Matos, J.E.

1985-01-01

A model for estimating the radiological consequences from a hypothetical accident in HEU and LEU fueled research and test reactors is presented. Simple hand calculations based on fission product yield table inventories and nonsite specific dispersion data may be adequate in many cases. However, more detailed inventories and site specific data on meteorological conditions and release rates and heights can result in substantial reductions in the dose estimates. LEU fuel gives essentially the same doses as HEU fuel. The plutonium buildup in the LEU fuel does not significantly increase the radiological consequences. The dose to the thyroid is the limiting dose. (author)

2011 Progress Report on HEU Minimization Activities in Argentina

Energy Technology Data Exchange (ETDEWEB)

Bonini, A.; Cristini, P.; Lio, L. De; Dell' Occhio, L.; Gil, D.; Gonzalez, A.G.; Gonzalez, R.; Varela, C. Komar; Lopez, M.; Novara, O.; Taboada, H. [Comision Nacional de Energia Atomica, Av. Del Libertador 8250 (1429) Buenos Aires (Argentina)

2011-07-01

After the core conversion of the RA-6 reactor finished in March 2008, an extension of the original CNEA-NNSA DoE contract was signed to enhance the final national HEU inventories minimization. Before this process, CNEA reserved a small inventory of HEU for R and D uses in fission chambers, neutronic probes and standards. This minimization comprises that all fresh and irradiated HEU remnant inventories coming from fuels and Mo99 irradiation targets fabrication and irradiated HEU-oxides retained in production filters and solutions will be recovered, down-blended into LEU and purified or dispose as waste whenever its recovery would not be advisable due to cost-benefit consideration. CNEA has a R and D program to develop the fabrication technology of both dispersed U-Mo (Al-Si matrix and Al cladding) and monolithic (Zry-4 cladding) miniplates to support the qualification activities of the RERTR program. Some monolithic 58% enrichment and LEU 8%Mo and U10%Mo miniplates and plates were and are being delivered to INL-DoE to be irradiated in the ATR reactor core. CNEA, a worldwide leader on LEU technology for fission radioisotope production is providing Brazil with 1/3 of the national requirements on Mo99 by weekly deliveries. Australia has started the fission radioisotope production through several batches by week, based on CNEA's LEU technology provided by INVAP SE. CNEA is also committed to improve the diffusion of LEU target and radiochemical technology for radioisotope production and target and process optimization. Future plans include: 1. Plans to recover and purify the LEU based inventories in Mo99 production filters, once the HEU to LEU campaign is over. 2. Fabrication and delivering to INL to be irradiated in the ATR core of U-8%Mo and U-10%Mo monolithic miniplates and development and fabrication of LEU very high density monolithic and dispersed U-Mo fuel plates with Zr cladding for the FUTURE-MONO experiment in the frame of the RERTR program. 3

Reactor Dynamics Experiments with a Sub-Critical Assembly

International Nuclear Information System (INIS)

Miley, G.H.; Yang, Y.; Wu, L.; Momota, H.

2004-01-01

A resurgence in use of nuclear power is now underway worldwide. However due to the shutdown of many university research reactors , student laboratories must rely more heavily on use of sub-critical assemblies. Here a driven sub-critical is described that uses a cylindrical Inertial Electrostatic Confinement (IEC) device to provide a fusion neutron source. The small IEC neutron source would be inserted in a fuel element position, with its power input controlled externally at a control panel. This feature opens the way to use of the critical assembly for a number of transient experiments such as sub-critical pulsing and neutron wave propagation. That in turn adds important new insights and excitement for the student teaching laboratory

Overview of Russian HEU transparency issues

International Nuclear Information System (INIS)

Kempf, C.R.; Bieniawski, A.

1993-01-01

The U.S. has signed an agreement with the Russian Federation for the purchase of 500 metric tons of highly-enriched uranium (HEU) taken from dismantled nuclear weapons. The HEU will be blended down to low-enriched uranium and will be transported to the U.S. to be used by fuel fabricators to make fuel for commercial nuclear power plants. Both the U.S. and Russia have been preparing to institute transparency measures to provide assurance that nonproliferation and arms control objectives specified in the agreement are met. This paper provides background information on the original agreement and on subsequent negotiations with the Russians, as well as discussion of technical aspects of developing transparency measures suited to the facilities and processes which are expected to be involved. Transparency has been defined as those agreed-upon measures which build confidence that arms control and non-proliferation objectives shared by the parties are met. Transparency is a departure from exhaustive, detailed arms control verification regimes of past agreements, which were based on a presumption of detecting transgressions as opposed to confirming compliance

Comparison of the FRM-II HEU design with an alternative LEU design

International Nuclear Information System (INIS)

Mo, S.C.; Hanan, N.A.; Matos, J.E.

2004-01-01

The FRM-II reactor design of the Technical University of Munich has a compact core that utilizes fuel plates containing highly-enriched uranium (HEU, 93%). This paper presents an alternative core design utilizing low-enriched uranium (LEU, 3 that provides nearly the same neutron flux for experiments as the HEU design, but has a less favourable fuel cycle economy. If an LEU fuel with a uranium density of 6.0 - 6.5 g/cm 3 . were developed, the alternative design would provide the same neutron flux and use the same number of cores per year as the HEU design. The results of this study show that there are attractive possibilities for using LEU fuel instead of HEU fuel in the FRM-II. Further optimization of the LEU design and near-term availability of LEU fuel with a uranium density greater than 4.8 g/cm 3 would enhance the performance of the LEU core. The REKIR Program is ready to exchange information with the Technical University of Munich to resolve any differences that may exist and to identify design modifications that would optimize reactor performance utilizing LEU fuel. (author)

Detection of illicit HEU production in gaseous centrifuge enrichment plants using neutron counting techniques on product cylinders

International Nuclear Information System (INIS)

Freeman, Corey R.; Geist, William H.

2010-01-01

Innovative and novel safeguards approaches are needed for nuclear energy to meet global energy needs without the threat of nuclear weapons proliferation. Part of these efforts will include creating verification techniques that can monitor uranium enrichment facilities for illicit production of highly-enriched uranium (HEU). Passive nondestructive assay (NDA) techniques will be critical in preventing illicit HEU production because NDA offers the possibility of continuous and unattended monitoring capabilities with limited impact on facility operations. Gaseous centrifuge enrichment plants (GCEP) are commonly used to produce low-enriched uranium (LEU) for reactor fuel. In a GCEP, gaseous UF 6 spins at high velocities in centrifuges to separate the molecules containing 238 U from those containing the lighter 235 U. Unfortunately, the process for creating LEU is inherently the same as HEU, creating a proliferation concern. Insuring that GCEPs are producing declared enrichments poses many difficult challenges. In a GCEP, large cascade halls operating thousands of centrifuges work together to enrich the uranium which makes effective monitoring of the cascade hall economically prohibitive and invasive to plant operations. However, the enriched uranium exiting the cascade hall fills product cylinders where the UF 6 gas sublimes and condenses for easier storage and transportation. These product cylinders hold large quantities of enriched uranium, offering a strong signal for NDA measurement. Neutrons have a large penetrability through materials making their use advantageous compared to gamma techniques where the signal is easily attenuated. One proposed technique for detecting HEU production in a GCEP is using neutron coincidence counting at the product cylinder take off stations. This paper discusses findings from Monte Carlo N-Particle eXtended (MCNPX) code simulations that examine the feasibility of such a detector.

Coretran/Vipre assembly critical power assessment against Nupec BWR experiments

International Nuclear Information System (INIS)

Aounallah, Y.

2001-01-01

This study has been performed, in the framework of the STARS project, to assess CORETRAN-01/VIPRE-02 code capability to predict critical heat flux conditions for BWR fuel assemblies. The assessment is based on comparisons of the code results with the NUPEC steady-state critical power measurements on full-scale assemblies tested under a range of flow conditions. Two assembly types were considered, the standard BWR 8 x 8 and the so-called ''high-burnup'' assembly, similar to GE-10. Code modelling options that have a significant impact on the results have been identified, along with code limitations. (author)

Coretran/Vipre assembly critical power assessment against Nupec BWR experiments

Energy Technology Data Exchange (ETDEWEB)

Aounallah, Y. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

2001-07-01

This study has been performed, in the framework of the STARS project, to assess CORETRAN-01/VIPRE-02 code capability to predict critical heat flux conditions for BWR fuel assemblies. The assessment is based on comparisons of the code results with the NUPEC steady-state critical power measurements on full-scale assemblies tested under a range of flow conditions. Two assembly types were considered, the standard BWR 8 x 8 and the so-called ''high-burnup'' assembly, similar to GE-10. Code modelling options that have a significant impact on the results have been identified, along with code limitations. (author)

ZPR-3 Assembly 6F : A spherical assembly of highly enriched uranium, depleted uranium, aluminum and steel with an average {sup 235}U enrichment of 47 atom %.

Energy Technology Data Exchange (ETDEWEB)

Lell, R. M.; McKnight, R. D; Schaefer, R. W.; Nuclear Engineering Division

2010-09-30

Over a period of 30 years, more than a hundred Zero Power Reactor (ZPR) critical assemblies were constructed at Argonne National Laboratory. The ZPR facilities, ZPR-3, ZPR-6, ZPR-9 and ZPPR, were all fast critical assembly facilities. The ZPR critical assemblies were constructed to support fast reactor development, but data from some of these assemblies are also well suited for nuclear data validation and to form the basis for criticality safety benchmarks. A number of the Argonne ZPR/ZPPR critical assemblies have been evaluated as ICSBEP and IRPhEP benchmarks. Of the three classes of ZPR assemblies, engineering mockups, engineering benchmarks and physics benchmarks, the last group tends to be most useful for criticality safety. Because physics benchmarks were designed to test fast reactor physics data and methods, they were as simple as possible in geometry and composition. The principal fissile species was {sup 235}U or {sup 239}Pu. Fuel enrichments ranged from 9% to 95%. Often there were only one or two main core diluent materials, such as aluminum, graphite, iron, sodium or stainless steel. The cores were reflected (and insulated from room return effects) by one or two layers of materials such as depleted uranium, lead or stainless steel. Despite their more complex nature, a small number of assemblies from the other two classes would make useful criticality safety benchmarks because they have features related to criticality safety issues, such as reflection by soil-like material. ZPR-3 Assembly 6 consisted of six phases, A through F. In each phase a critical configuration was constructed to simulate a very simple shape such as a slab, cylinder or sphere that could be analyzed with the limited analytical tools available in the 1950s. In each case the configuration consisted of a core region of metal plates surrounded by a thick depleted uranium metal reflector. The average compositions of the core configurations were essentially identical in phases A - F. ZPR-3

Verification experiment on the downblending of high enriched uranium (HEU) at the Portsmouth Gaseous Diffusion Plant. Digital video surveillance of the HEU feed stations

International Nuclear Information System (INIS)

Martinez, R.L.; Tolk, K.; Whiting, N.; Castleberry, K.; Lenarduzzi, R.

1998-01-01

As part of a Safeguards Agreement between the US and the International Atomic Energy Agency (IAEA), the Portsmouth Gaseous Diffusion Plant, Piketon, Ohio, was added to the list of facilities eligible for the application of IAEA safeguards. Currently, the facility is in the process of downblending excess inventory of HEU to low enriched uranium (LEU) from US defense related programs for commercial use. An agreement was reached between the US and the IAEA that would allow the IAEA to conduct an independent verification experiment at the Portsmouth facility, resulting in the confirmation that the HEU was in fact downblended. The experiment provided an opportunity for the DOE laboratories to recommend solutions/measures for new IAEA safeguards applications. One of the measures recommended by Sandia National Laboratories (SNL), and selected by the IAEA, was a digital video surveillance system for monitoring activity at the HEU feed stations. This paper describes the SNL implementation of the digital video system and its integration with the Load Cell Based Weighing System (LCBWS) from Oak Ridge National Laboratory (ORNL). The implementation was based on commercially available technology that also satisfied IAEA criteria for tamper protection and data authentication. The core of the Portsmouth digital video surveillance system was based on two Digital Camera Modules (DMC-14) from Neumann Consultants, Germany

The Bare Critical Assembly of Natural Uranium and Heavy Water

Energy Technology Data Exchange (ETDEWEB)

Popovic, D [Boris Kidric Institute of Nuclear Sciences, Vinca, Belgrade (Yugoslavia)

1958-07-01

The first reactor built in Yugoslavia was the bare zero energy heavy water and natural uranium assembly at the Boris Kidric Institute of Nuclear Sciences, Belgrade. The reactor went critical on April 29, 1958. The possession of four tons of natural uranium metal and the temporary availability of seven tons of heavy water encouraged the staff of the Institute to build a critical assembly. A critical assembly was chosen, rather than high flux reactor, because the heavy water was available only temporarily. Besides, a 10 MW, enriched uranium, research reactor is being built at the same Institute and should be ready for operation late this year. It was supposed that the zero energy reactor would provide experience in carrying out critical experiments, operational experience with nuclear reactors, and the possibility for an extensive program in reactor physics. (author)

Benchmark criticality experiments for fast fission configuration with high enriched nuclear fuel

International Nuclear Information System (INIS)

Sikorin, S.N.; Mandzik, S.G.; Polazau, S.A.; Hryharovich, T.K.; Damarad, Y.V.; Palahina, Y.A.

2014-01-01

Benchmark criticality experiments of fast heterogeneous configuration with high enriched uranium (HEU) nuclear fuel were performed using the 'Giacint' critical assembly of the Joint Institute for Power and Nuclear Research - Sosny (JIPNR-Sosny) of the National Academy of Sciences of Belarus. The critical assembly core comprised fuel assemblies without a casing for the 34.8 mm wrench. Fuel assemblies contain 19 fuel rods of two types. The first type is metal uranium fuel rods with 90% enrichment by U-235; the second one is dioxide uranium fuel rods with 36% enrichment by U-235. The total fuel rods length is 620 mm, and the active fuel length is 500 mm. The outer fuel rods diameter is 7 mm, the wall is 0.2 mm thick, and the fuel material diameter is 6.4 mm. The clad material is stainless steel. The side radial reflector: the inner layer of beryllium, and the outer layer of stainless steel. The top and bottom axial reflectors are of stainless steel. The analysis of the experimental results obtained from these benchmark experiments by developing detailed calculation models and performing simulations for the different experiments is presented. The sensitivity of the obtained results for the material specifications and the modeling details were examined. The analyses used the MCNP and MCU computer programs. This paper presents the experimental and analytical results. (authors)

Organization and methods of radiation monitoring while working at nuclear critical assemblies

International Nuclear Information System (INIS)

Shishkin, G.V.; Komissarov, L.A.

1980-01-01

The organization and methods of environmental radiation monitoring while working at nuclear critical assemblies, are described. Necessary equipment for critical assemblies (signal and Ventilation systems, devices for recording accidental radiation levels of and for measuring radiation field distribution) and the personnel program of actions in case of nuclear accident. The dosimetric control at critical assemblies is usually ensured by telesystems. 8004-01 multi-channel dosimetric device is described as an example of such-system [ru

Neutronic performance of a 14 MW TRIGA reactor: LEU vs HEU fuel

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Cornella, R.J.

1983-01-01

A primary objective of the US Reduced Enrichment Research and Test Reactor (RERTR) Program is to develop means for replacing, wherever possible, currently used highly-enriched uranium (HEU) fuel ( 235 U enrichment > 90%) with low-enriched uranium (LEU) fuel ( 235 U enrichment < 20%) without significantly degrading the performance of research and test reactors. The General Atomic Company has developed a low-enriched but high uranium content Er-U-ZrH/sub 1.6/ fuel to enable the conversion of TRIGA reactors (and others) from HEU to LEU. One possible application is to the water-moderated 14 MW TRIGA Steady State Reactor (SSR) at the Romanian Institute for Nuclear Power Reactors. The work reported here was undertaken for the purpose of comparing the neutronic performance of the SSR for HEU fuel with that for LEU fuel. In order to make these relative comparisons as valid as possible, identical methods and models were used for the neutronic calculations

HEU to LEU conversion and blending facility: Oxide blending alternative to produce LEU oxide for commercial use

International Nuclear Information System (INIS)

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This document provides data to be used in the environmental impact analysis for the oxide blending HEU disposition option. This option provides for a yearly HEU throughput of 1 0 metric tons (MT) of uranium metal with an average U235 assay of 50% blended with 165 MT of natural assay triuranium octoxide (U 3 O 8 ) per year to produce 177 MT of 4% U235 assay U 3 O 8 , for LWR fuel. Since HEU exists in a variety of forms and not necessarily in the form to be blended, worst case scenarios for preprocessing prior to blending will be assumed for HEU feed streams

Ion-induced gammas for photofission interrogation of HEU.

Energy Technology Data Exchange (ETDEWEB)

Doyle, Barney Lee (Sandia National Laboratories, Albuquerque, NM); Antolak, Arlyn J.; Morse, Daniel H.; Provencio, Paula Polyak (Sandia National Laboratories, Albuquerque, NM)

2006-03-01

High-energy photons and neutrons can be used to actively interrogate for heavily shielded special nuclear material (SNM), such as HEU (highly enriched uranium), by detecting prompt and/or delayed induced fission signatures. In this work, we explore the underlying physics for a new type of photon source that generates high fluxes of mono-energetic gamma-rays from low-energy (<500 keV) proton-induced nuclear reactions. The characteristic energies (4- to 18-MeV) of the gamma-rays coincide with the peak of the photonuclear cross section. The source could be designed to produce gamma-rays of certain selected energies, thereby improving the probability of detecting shielded HEU or providing a capability to determine enrichment inside sealed containers. The fundamental physics of such an interrogation source were studied in this LDRD through scaled ion accelerator experiments and radiation transport modeling. The data were used to assess gamma and neutron yields, background, and photofission-induced signal levels from several (p,{gamma}) target materials under consideration.

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal

HEU to LEU conversion and blending facility: UNH blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than is the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This report provides data to be used in the environmental impact analysis for the uranyl nitrate hexahydrate blending option to produce oxide for disposal. This the Conversion and Blending Facility (CBF) alternative will have two missions (1) convert HEU materials into HEU uranyl nitrate (UNH) and (2) blend the HEU uranyl nitrate with depleted and natural assay uranyl nitrate to produce an oxide that can be stored until an acceptable disposal approach is available. The primary emphasis of this blending operation will be to destroy the weapons capability of large, surplus stockpiles of HEU. The blended LEU product can only be made weapons capable again by the uranium enrichment process. The blended LEU will be produced as a waste suitable for storage or disposal.

Forensic analysis of a smuggled HEU sample interdicted in Bulgaria

International Nuclear Information System (INIS)

Niemeyer, S.; Hutcheon, I.

2002-01-01

impurities are too high for a laboratory-scale-operation. We determined the age of the chemical reprocessing by using seven nuclide systems. Using the multiple clocks enables us to evaluate the validity of the assumptions in the dating schemes. The slightly higher ages for Am and Ac chronometers are consistent with a Purex process. The mean age of the remaining clocks is October 30, 1993, with an uncertainty of only 25 days. The similar age for the Pu/Am clock suggests that the Pu is not from postprocessing contamination. The non-nuclear materials provide a number of forensic clues. The yellow, waxy liner material is an uncommon type of paraffin wax. The wax has unusual organic compounds (naphthalene derivatives). The yellow colorant is Ba-chromate. This colorant is rare in western countries but common in Brazil, China, India, and Eastern Europe. The ampoule is composed of common borosilicate glass. We note that ampoules have been used as containers for archiving nuclear samples, but a glass ampoule has not been previously reported as a container for a smuggled nuclear sample. Two pieces of paper were analyzed--one piece was attached to the exterior of the lead container and the other paper was wrapped around the ampoule. Both papers contain softwood and hardwood species, and the fibers were produced by the Kraft pulping process. The specific species of wood are definitely not from North America or Western Europe, but they are consistent with Eastern Europe. Finally, the lead container is hardened with 5 wt% antimony. The Pb isotope composition excludes U.S. ores but is consistent with Pb from several European and Asian mines. Taken all together, the non-nuclear evidence is most consistent with assembly of the package in Eastern Europe from local sources. The nuclear isotopics can be used to constrain the type of reactor in which the HEU was irradiated. Detailed reactor calculations were performed using WIMS and GLASS codes for a pin fuel cell geometry. The results point to

Passive Time Coincidence Measurements with HEU and DU Metal Castings

International Nuclear Information System (INIS)

McConchie, Seth M.; Hausladen, Paul; Mihalczo, John T.; Wright, Michael C.; Archer, Daniel E.

2008-01-01

A Department of Energy sponsored Oak Ridge National Laboratory/Y-12 National Security Complex program of passive time coincidence measurements has been initiated at Y-12 to evaluate the ability to determine the presence of high enriched uranium (HEU) and distinguish it from depleted uranium (DU). This program uses the Nuclear Materials Identification System (NMIS) without an active interrogation source. Previous passive NMIS measurements with Pu metal and Pu oxide have been successful in determining the Pu mass, assuming a known 240Pu content. The spontaneous fission of uranium metal is considerably lower than Pu and measurements of this type have been performed at Lawrence Livermore National Laboratory. This work presents results of measurements of HEU and DU metal castings using moderated 3He detectors.

Measurements of the HEU and LEU in-core spectra at the Ford Nuclear Reactor

Energy Technology Data Exchange (ETDEWEB)

Wehe, D K [Oak Ridge National Laboratory, Oak Ridge, TN (United States); King, J S; Lee, J C; Martin, W R [Department of Nuclear Engineering, University of Michigan, Ann Arbor, MI (United States)

1985-07-01

The Ford Nuclear Reactor (FNR) at the University of Michigan has been serving as the test site for a low-enriched uranium (LEU) fuel whole-core demonstration. As part of the experimental program, the differential neutron spectrum has been measured in a high-enriched uranium (HEU) core and an LEU core. The HEU and LEU spectra were determined by unfolding the measured activities of foils that were irradiated in the reactor. When the HEU and LEU spectra are compared from meV to 10 MeV, significant differences between the two spectra are apparent below 10 eV. These are probably caused by the additional {sup 238}U resonance absorption in the LEU fuel. No measurable difference occurs in the shape of the spectra above MeV. (author)

Mixed core conversion study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1984-01-01

The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically

Safety Analysis Report for Packaging, Y-12 National Security Complex, Model ES-3100 Package with Bulk HEU Contents

Energy Technology Data Exchange (ETDEWEB)

Anderson, James [Y-12 National Security Complex, Oak Ridge, TN (United States); Goins, Monty [Y-12 National Security Complex, Oak Ridge, TN (United States); Paul, Pran [Y-12 National Security Complex, Oak Ridge, TN (United States); Wilkinson, Alan [Y-12 National Security Complex, Oak Ridge, TN (United States); Wilson, David [Y-12 National Security Complex, Oak Ridge, TN (United States)

2015-09-03

This safety analysis report for packaging (SARP) presents the results of the safety analysis prepared in support of the Consolidated Nuclear Security, LLC (CNS) request for licensing of the Model ES-3100 package with bulk highly enriched uranium (HEU) contents and issuance of a Type B(U) Fissile Material Certificate of Compliance. This SARP, published in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guide 7.9 and using information provided in UCID-21218 and NRC Regulatory Guide 7.10, demonstrates that the Y-12 National Security Complex (Y-12) ES-3100 package with bulk HEU contents meets the established NRC regulations for packaging, preparation for shipment, and transportation of radioactive materials given in Title 10, Part 71, of the Code of Federal Regulations (CFR) [10 CFR 71] as well as U.S. Department of Transportation (DOT) regulations for packaging and shipment of hazardous materials given in Title 49 CFR. To protect the health and safety of the public, shipments of adioactive materials are made in packaging that is designed, fabricated, assembled, tested, procured, used, maintained, and repaired in accordance with the provisions cited above. Safety requirements addressed by the regulations that must be met when transporting radioactive materials are containment of radioactive materials, radiation shielding, and assurance of nuclear subcriticality.

HEU to LEU conversion and blending facility: Oxide blending alternative to produce LEU oxide for commercial use

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

The United States Department of Energy (DOE) is examining options for the disposition of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. Disposition is a process of use or disposal of material that results in the material being converted to a form that is substantially and inherently more proliferation-resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. This document provides data to be used in the environmental impact analysis for the oxide blending HEU disposition option. This option provides for a yearly HEU throughput of 1 0 metric tons (MT) of uranium metal with an average U235 assay of 50% blended with 165 MT of natural assay triuranium octoxide (U{sub 3} O{sub 8}) per year to produce 177 MT of 4% U235 assay U{sub 3} O{sub 8}, for LWR fuel. Since HEU exists in a variety of forms and not necessarily in the form to be blended, worst case scenarios for preprocessing prior to blending will be assumed for HEU feed streams.

Safety considerations of new critical assembly for the Research Reactor Institute, Kyoto University

International Nuclear Information System (INIS)

Umeda, Iwao; Matsuoka, Naomi; Harada, Yoshihiko; Miyamoto, Keiji; Kanazawa, Takashi

1975-01-01

The new critical assembly type of nuclear reactor having three cores for the first time in the world was completed successfully at the Research Reactor Institute of Kyoto University in autumn of 1974. It is called KUCA (Kyoto University Critical Assembly). Safety of the critical assembly was considered sufficiently in consequence of discussions between the researchers of the institute and the design group of our company, and then many bright ideas were created through the discussions. This paper is described the new safety design of main equipments - oil pressure type center core drive mechanism, removable water overflow mechanism, core division mechanism, control rod drive mechansim, protection instrumentation system and interlock key system - for the critical assembly. (author)

Verification of homogenization in fast critical assembly analyses

International Nuclear Information System (INIS)

Chiba, Go

2006-01-01

In the present paper, homogenization procedures for fast critical assembly analyses are investigated. Errors caused by homogenizations are evaluated by the exact perturbation theory. In order to obtain reference solutions, three-dimensional plate-wise transport calculations are performed. It is found that the angular neutron flux along plate boundaries has a significant peak in the fission source energy range. To treat this angular dependence accurately, the double-Gaussian Chebyshev angular quadrature set with S 24 is applied. It is shown that the difference between the heterogeneous leakage theory and the homogeneous theory is negligible, and that transport cross sections homogenized with neutron flux significantly underestimate neutron leakage. The error in criticality caused by a homogenization is estimated at about 0.1%Δk/kk' in a small fast critical assembly. In addition, the neutron leakage is overestimated by both leakage theories when sodium plates in fuel lattices are voided. (author)

Operating procedures for the Pajarito Site Critical Assembly Facility

International Nuclear Information System (INIS)

Malenfant, R.E.

1983-03-01

Operating procedures consistent with DOE Order 5480.2, Chapter VI, and the American National Standard Safety Guide for the Performance of Critical Experiments are defined for the Pajarito Site Critical Assembly Facility of the Los Alamos National Laboratory. These operating procedures supersede and update those previously published in 1973 and apply to any criticality experiment performed at the facility

Thor, a thorium-reflected plutonium-metal critical assembly

International Nuclear Information System (INIS)

Hansen, G.E.; Paxton, H.C.

1979-01-01

Critical specifications of Thor, an old assembly of thorium-reflected plutonium, have been refined. These specifications are brought together with void coefficients, Rossi-alpha values, fission traverses, and spectral indices

Criticality safety evaluation report for FFTF 42% fuel assemblies

International Nuclear Information System (INIS)

Richard, R.F.

1997-01-01

An FFTF tritium/isotope production mission will require a new fuel supply. The reference design core will use a mixed oxide fuel nominally enriched to 40 wt% Pu. This enrichment is significantly higher than that of the standard Driver Fuel Assemblies used in past operations. Consequently, criticality safety for handling and storage of this fuel must be addressed. The purpose of this document is to begin the process by determining the minimum critical number for these new fuel assemblies in water, sodium and air. This analysis is preliminary and further work can be done to refine the results reported here. Analysis was initially done using 45 wt 5 PuO. Additionally, a preliminary assessment is done concerning storage of these fuel assemblies in Interim Decay Storage (IDS), Fuel Storage Facility (FSF), and Core Component Containers/Interim Storage Casks (CCC/ISC)

HEU to LEU Conversion and Blending Facility: UNH blending alternative to produce LEU UNH for commercial use

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form that is more proliferation-resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. Five technologies for blending HEU will be assessed. This document provides data to be used in the environmental impact analysis for the UNH blending HEU disposition option. Process requirements, resource needs, employment needs, waste/emissions from plant, hazards, accident scenarios, and intersite transportation are discussed.

HEU and Leu FueL Shielding Comparative Study Applied for Spent Fuel Transport

International Nuclear Information System (INIS)

Margeanu, C.A.; Margeanu, S.; Barbos, D.

2009-01-01

INR Pitesti owns and operates a TRIGA dual-core Research Reactor for material testing, power reactor fuel and nuclear safety studies. The dual core concept involves the operation of a 14 MW TRIGA steady-state, high flux research and material testing reactor at one end of a large pool, and the independent operation of an annular-core pulsing reactor (TRIGA-ACPR) at the other end of the pool. The steady-state reactor is mostly used for long term testing of power reactor fuel components (pellets, pins, subassemblies and fuel assemblies) followed by post-irradiation examination. Following the general trend to replace the He fuel type (High Enriched Uranium) by Leu fuel type (Low Enriched Uranium), in the light of international agreements between IAEA and the states using He fuel in their nuclear reactors, Inr Past's have been accomplished the TRIGA research reactor core full conversion on May 2006. The He fuel repatriation in US in the frame of Foreign Research Reactor Spent Nuclear Fuel Return Programme effectively started in 1999, the final stage being achieved in summer of 2008. Taking into account for the possible impact on the human and environment, in all activities associated to nuclear fuel cycle, the spent fuel or radioactive waste characteristics must be well known. Shielding calculations basic tasks consist in radiation doses calculation, in order to prevent any risks both for personnel protection and impact on the environment during the spent fuel manipulation, transport and storage. The paper is a comparative study of Leu and He fuel utilization effects for the shielding analysis during spent fuel transport. A comparison against the measured data for He spent fuel, available from the last stage of the spent fuel repatriation, is presented. All the geometrical and material data related on the spent fuel shipping cask were considered according to the Nac-Lt Cask approved model. The shielding analysis estimates radiation doses to shipping cask wall surface

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation.

HEU to LEU conversion and blending facility: Metal blending alternative to produce LEU oxide for disposal

International Nuclear Information System (INIS)

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials. The nuclear material is converted to a form more proliferation- resistant than the original form. Blending HEU (highly enriched uranium) with less-enriched uranium to form LEU has been proposed as a disposition option. Five technologies are being assessed for blending HEU. This document provides data to be used in environmental impact analysis for the HEU-LEU disposition option that uses metal blending with an oxide waste product. It is divided into: mission and assumptions, conversion and blending facility descriptions, process descriptions and requirements, resource needs, employment needs, waste and emissions from plant, hazards discussion, and intersite transportation

Refinement of criticality and breeding parameters by means of experiments on a series of critical assemblies

International Nuclear Information System (INIS)

Golubev, V.I.; Dulin, V.A.; Kazanskij, Yu.A.; Mamontov, V.M.; Mozhaev, V.K.; Sidorov, G.I.

1980-01-01

A programme of measurements was performed on a number of critical assemblies with the aim of obtaining reliable experimental data under conditions approximating the simplest calculation model. To this end the neutron balance at the centres of the BFS-31, BFS-33, BFS-35, BFS-38, KBR-3 and KBR-7 critical assemblies was investigated. These assemblies contained central inserts made of uranium dioxide (BFS-33), natural uranium oxide and plutonium metal (BFS-31), natural uranium and plutonium metal (BFS-38), 90% enriched metallic uranium and stainless steel (KBR-3) and enriched uranium dioxide and nickel (KBR-7). The composition of the inserts was such that Ksub(infinite)=1. The K + values, the ratios of the reaction rates of the principal raw material and fissionable isotopes and the reactivity coefficients of a number of materials were measured in the inserts. The components of the breeding coefficient were measured at the centre of the BFS-39 critical assembly which simulates a power reactor (simplest composition with low- and high-enrichment zones and no control mechanism). The authors describe briefly the critical assemblies, the methods of measurement and calculation and methods of correcting for differences between the calculation model and the conditions under which the measurements were performed and compare the results of the experiments with the corresponding theoretical values obtained using various systems of group constants. In their latest versions, the group constants derived from different sets of integral experiments describe the experimental data much better than was previously possible. The deviations which occur in the predicted criticality and breeding parameters using different versions of the constants essentially reflect the difference in the results of the sets of integral experiments that were used for the group constants. (author)

Development of training simulator based on critical assemblies test bench

International Nuclear Information System (INIS)

Narozhnyi, A.T.; Vorontsov, S.V.; Golubeva, O.A.; Dyudyaev, A.M.; Il'in, V.I.; Kuvshinov, M.I.; Panin, A.V.; Peshekhonov, D.P.

2007-01-01

When preparing critical mass experiment, multiplying system (MS) parts are assembled manually. This work is connected with maximum professional risk to personnel. Personnel training and keeping the skill of working experts is the important factor of nuclear safety maintenance. For this purpose authors develop a training simulator based on functioning critical assemblies test bench (CATB), allowing simulation of the MS assemblage using training mockups made of inert materials. The control program traces the current status of MS under simulation. A change in the assembly neutron physical parameters is mapped in readings of the regular devices. The simulator information support is provided by the computer database on physical characteristics of typical MS components The work in the training mode ensures complete simulation of real MS assemblage on the critical test bench. It makes it possible to elaborate the procedures related to CATB operation in a standard mode safely and effectively and simulate possible abnormal situations. (author)

Criticality safety of storage barrels for enriched uranium fresh fuel at the RB research reactor

International Nuclear Information System (INIS)

Pesic, M. P.

1997-01-01

Study on criticality safety of fresh low and high enriched uranium (LEU and HEU) fuel elements in the storage/transport barrels at the RB research reactor is carried out by using the well-known MCNP computer code. It is shown that studied arrays of tightly closed fuel barrels, each entirely loaded with 100 fresh (HEU or LEU) fuel slugs, are far away from criticality, even in cases of an unexpected flooding by light water.(author)

A mixed core conversion study with HEU and LEU fuels

International Nuclear Information System (INIS)

Matos, J.E.; Freese, K.E.

1985-01-01

The results of a mixed core study are presented for gradual replacement of HEU fuel with LEU fuel using the IAEA generic 10 MW reactor as an example. The key parameters show that the transition can be accomplished safely and economically. (author)

Performance of an active well coincidence counter for HEU samples

International Nuclear Information System (INIS)

Ferrari, Francesca; Peerani, Paolo

2010-01-01

Neutron coincidence counting is the reference NDA technique used in nuclear safeguards to measure the mass of nuclear material in samples. For high-enriched uranium (HEU) samples active neutron interrogation is generally performed and the most common device used by nuclear inspectors is the Active Well Coincidence Counter (AWCC). Within her master thesis at the Polytechnic of Milan, the first author performed an intensive study on the characteristics and performances of the AWCC in order to assess the 235 U mass in HEU oxide samples at the PERLA laboratory of JRC. The work has been summarised in this paper that starts with the optimisation of the use of AWCC for nuclear safeguards, describing the calibration procedure, reporting results of a series of verification measurements, summarising the performances that can be obtained with this instruments during inspections at fuel production plants and concluding with the discussion of uncertainties related to these measurements.

What the difference to use LEU and HEU fuel elements separately or together in a research reactor

International Nuclear Information System (INIS)

Kaya, S.; Uestuen, G.

2005-01-01

Concerning of nuclear material safety, most of the research reactors are advised to shift from HEU (high enriched-%93 U-235) to LEU (low enriched-%20 U-235) fuel elements. When LEU and HEU fuel elements are to be used together in a research reactor, some design and safety problems are encountered. According to use of the reactor, some research reactors such as MTR type may not show any considerable difference for HEU or LEU fuel elements, but the efficiency of radioisotope production generated by thermal neutron interaction may decrease about twenty-thirty percent when LEU fuel elements are used. Here, fine mesh-sized 3D neutronic analysis of TR-2 research reactor is presented to indicate the arising problem when LEU end HEU fuel elements are used together in a research reactor. Partial thermohydraulic analysis of the reactor is also given to show the betterness of the LEU fuel element design. However, there might be some points that should be noticed for safer operation of plate type fuelled research reactors. (author)

Status of HEU-LEU conversion of FRJ-2

International Nuclear Information System (INIS)

Damm, G.; Nabbi, R.

2002-01-01

The operator of the German FRJ-2 research reactor, 'Research Center Juelich', has participated from the beginning in the RERTR programme and made comprehensive contributions to the test and use of LEU fuel for HEU-LEU-conversion measures. The originally planned time scale for the conversion of FRJ-2 was significantly delayed because of a change of the manufacturer of the LEU fuel elements and a 4 years shutdown of the reactor for refurbishment purposes. In the meantime the new LEU fuel elements are qualified and tested in the reactor. In the moment calculations for the safety report are made and it is planned to apply for the license of FRJ-2 operation with LEU fuel at the beginning of 2003. In order to get most reliable results a sophisticated computational method based on a MCNP model coupled with the depletion code BURN was developed for reactor physical calculations, core conversion studies and fuel element performance analysis and applied to the mixed and LEU core. The licensing schedule and results of latest calculations for the conversion study will be presented. The simulations shows that the thermal flux in the LEU core is about 19% resulting in a lower burnup rate. But in the reflector area around the core and in the center of the cold n source the neutron flux reduction remains limited to 6%. Due to a harder neutron spectrum in the LEU core the kinetic and safety related parameters are slightly reduced. Using the ORIGEN code it could be shown that the increase of the total fission products inventory amounts to about 6% compared to a HEU core. As a consequence of the high amount of U-238, the amount of U-235 in the LEU core has to be about 27% higher than in the HEU core but the U-235 burnup is approx. 5% lower due to the contribution of fissile plutonium. (author)

Comparison of HEU and LEU neutron spectra in irradiation facilities at the Oregon State TRIGA® Reactor

International Nuclear Information System (INIS)

Schickler, R.A.; Marcum, W.R.; Reese, S.R.

2013-01-01

Highlights: • The Oregon State TRIGA ® Reactor neutron spectra is characterized herein. • Neutron spectra between highly enriched uranium and low enriched uranium cores are compared. • Discussion is given as to differences between HEU and LEU core spectra results and impact on experiments. -- Abstract: In 2008, the Oregon State TRIGA ® Reactor (OSTR) was converted from highly enriched uranium (HEU) fuel lifetime improvement plan (FLIP) fuel to low-enriched uranium (LEU) fuel. This effort was driven and supported by the Department of Energy's (DoE's) Reduced Enrichment for Research and Test Reactors (RERTR) program. The basis behind the RERTR program's ongoing conversion effort is to reduce the nuclear proliferation risk of civilian research and test reactors. The original intent of the HEU FLIP fuel was to provide fuel to research reactors that could be utilized for many years before a necessary refueling cycle. As a research reactor, the OSTR provides irradiation facilities for a variety of applications, such as activation analysis, fission-track dating, commercial isotope production, neutron radiography, prompt gamma characterization, and many others. In order to accurately perform these research functions, several studies had been conducted on the HEU FLIP fuel core to characterize the neutron spectra in various experimental facilities of the OSTR (Tiyapun, 1997; Ashbaker, 2005). As useful as these analyses were, they are no longer valid due to the change in fuel composition and the resulting alteration of core performance characteristics. Additionally, the core configuration (fuel reconfiguration) was altered between the HEU and LEU cores. This study characterizes the neutron spectra in various experimental facilities within and around the current LEU core. It also compares the spectra to that which was yielded in the HEU core through use of Monte Carlo n-Particle 5 (MCNP5) and experimental adjustment via a least-squares technique. The quantification of

Comparison of thermohydraulic and nuclear aspects in a standard HEU core and a typical LEU core for the HFR Petten. A case study

International Nuclear Information System (INIS)

Pruimboom, H.; Tas, A.

1985-01-01

Within the framework of the RERTR program various HEU-LEU core calculations have been performed by ANL in a cooperative effort with ECN and JRC Petten. The main purpose of this work has been to gain competence in analysing HEU-LEU core conversion for high power Materials Testing Reactors and to assist in a possible HEU-LEU conversion of the HFR Petten. For reference purposes the present HFR standard core (HEU) in the 'old' vessel geometry was calculated at first. As a next step the new vessel geometry and the increased fuel weights were taken into account. Subsequently various LEU HFR core options have been analysed. Main parameters in the LEU study were the uranium loading in the meat, the fuel type, the thickness of the meat, the number of fuel plates per element and the type of burnable poison applied. Though the study has not yet been completed, one of its striking preliminary results concerns the increased power peaking in the LEU fuel elements as compared with the HEU situation. A preliminary analysis of the thermal characteristics of a typical LEU core as compared with a standard HEU core has been made and is presented in the paper. A short survey of the various HEU and LEU calculations is given. The thermal safety analysis procedure for the HFR, as based on the flow instability criterion, is clarified. Finally, the thermal comparison HEU versus LEU and the resulting conclusions are presented. (author)

New calculations for critical assemblies using MCNP4B

International Nuclear Information System (INIS)

Adams, A.A.; Frankle, S.C.; Little, R.C.

1997-07-01

A suite of 41 criticality benchmarks has been modeled using MCNP trademark (version 4B). Most of the assembly specifications were obtained from the Cross Section Evaluation Working Group (CSEWG) and the International Criticality Safety Benchmark Evaluation Project (ICSBEP) compendiums of experimental benchmarks. A few assembly specifications were obtained from experimental papers. The suite contains thermal and fast assemblies, bare and reflected assemblies, and emphasizes 233 U, 235 U, 238 U, and 239 Pu. The values of k eff for each assembly in the suite were calculated using MCNP libraries derived primarily from release 2 of ENDF/B-V and release 2 of ENDF/B-VI. The results show that the new ENDF/B-VI.2 evaluations for H, O, N, B, 235 U, 238 U, and 239 Pu can have a significant impact on the values of k eff . In addition to the integral quantity k eff , several additional experimental measurements were performed and documented. These experimental measurements include central fission and reaction-rate ratios for various isotopes, and neutron leakage and flux spectra. They provide more detailed information about the accuracy of the nuclear data than can k eff . Comparison calculations were performed using both ENDF/B-V.2 and ENDF/B-VI.2-based data libraries. The purpose of this paper is to compare the results of these additional calculations with experimental data, and to use these results to assess the quality of the nuclear data

On the importance of ending the use of HEU in the nuclear fuel cycle: An updated assessment

International Nuclear Information System (INIS)

Glaser, Alexander; Hippel, Frank von

2002-01-01

The events of September 2001 have created a renewed urgency with regard to the disposition and future use and management of nuclear-weapons-usable materials. Highly enriched uranium (HEU) has received particular attention because it is relatively easy to use in a nuclear weapon and therefore an obvious candidate for diversion or theft by state or nonstate actors. The role of the RERTR program in this context and its contribution to global security can hardly be overemphasized. This article reviews existing or proposed activities to reduce the threat posed by HEU, how these activities are linked to the RERTR program, and outlines the most urgent steps to be taken to approach the ultimate objective of eliminating non-weapons HEU inventories in the world. (author)

Safe Operation of Critical Assemblies and Research Reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1961-05-15

This Manual is provided as a guide to the safe operation of critical assemblies and small research reactors. It is intended that it should be used by all authorities and persons concerned with, or responsible for, the use of such equipment, in addition to the scientists and technologists who are actually working with, or operating it. It is suggested that it will be of use to those wishing to design and manufacture, or purchase, critical assemblies or research reactors, as well as those already in possession of them, and that it will prove particularly helpful to those users who have no direct access to other collected sources of information. This Manual is not a set of rules or a code of practice, but a series of recommendations which must be interpreted with scientific judgement in their application to any particular problem. The guiding principles are given from which good operational procedures may be established and improved. The promulgation of rigid standards is both impossible and undesirable at the present time, since the topics discussed form part of a rapidly growing science and technology. Therefore, any recommendations made should not be used to restrict or inhibit future developments. The Manual is intended mainly for use in those Member States where there has been little experience in the operation of critical assemblies and research reactors. It has been compounded from the best practices which exist in Member States having a large amount of such experience, so that nothing in it should conflict with the best practices to be encountered in the field of safe operation.

Safe Operation of Critical Assemblies and Research Reactors

International Nuclear Information System (INIS)

1961-01-01

This Manual is provided as a guide to the safe operation of critical assemblies and small research reactors. It is intended that it should be used by all authorities and persons concerned with, or responsible for, the use of such equipment, in addition to the scientists and technologists who are actually working with, or operating it. It is suggested that it will be of use to those wishing to design and manufacture, or purchase, critical assemblies or research reactors, as well as those already in possession of them, and that it will prove particularly helpful to those users who have no direct access to other collected sources of information. This Manual is not a set of rules or a code of practice, but a series of recommendations which must be interpreted with scientific judgement in their application to any particular problem. The guiding principles are given from which good operational procedures may be established and improved. The promulgation of rigid standards is both impossible and undesirable at the present time, since the topics discussed form part of a rapidly growing science and technology. Therefore, any recommendations made should not be used to restrict or inhibit future developments. The Manual is intended mainly for use in those Member States where there has been little experience in the operation of critical assemblies and research reactors. It has been compounded from the best practices which exist in Member States having a large amount of such experience, so that nothing in it should conflict with the best practices to be encountered in the field of safe operation.

Criticality studies of fast assemblies with the new 27-group cross-section set

International Nuclear Information System (INIS)

Garg, S.B.; Shukla, V.K.

1976-01-01

A test of 27-group cross-section set (Garg-set) recently derived from ENDF/B library has been carried out in the criticality studies of the Pu 239 , U 235 and U 233 based metal, oxide and carbide fuelled fast critical assemblies. A total of twenty fast critical assemblies of different sizes and varying neutron spectra have been selected for analysis. Based on these analyses it has been observed that the Garg-set predicts well the criticality of uranium and plutonium based hard-spectra assemblies. In the soft-spectra systems it underpredicts criticality because of the following reasons: (a) It makes use of the higher capture cross-sections of structural and coolant elements given in ENDF/B - Version IV library. (b) It does not account for the resonance self-shielding effects of cross-sections. It has also been observed that the Garg-set gives better results than the MABBN-set for dense and dilute plutonium-based and the hard uranium-based assemblies. This superior trend of the Garg-set is slightly lost in the uranium-based dilute systems because of large differences in the capture cross-sections of structural elements of these two sets. (author)

Russian RERTR program as a part of Joint US DOE-RF MINATOM collaboration on elimination of the threat connected to the use of HEU in research reactors

International Nuclear Information System (INIS)

Arkhangelsky, N.

2002-01-01

The Russian RERTR Program started at the end of 70's, the final goal of the program is to eliminate supplies of HEU in fuel elements and assemblies for foreign research reactors that were designed according to Russian projects. Basic directions of the work include: completion of the development of the fuel elements and assemblies on a basis of uranium dioxide; development of the fuel on a basis of U-Mo alloy; and development of pin type fuel elements. Fuel assemblies of WWR-M2 type with LEU were developed and qualified for using in foreign research reactors that use such type of fuel assemblies. These assemblies are ready for the supplying several operating foreign research reactors. There are more than 20 sites in Eastern European countries, former Soviet republics and another countries that have big amount of Russian origin HEU in fresh and spent fuel. The problem of the shipment of SNF from sites of research reactors is also very important for domestic Russian research reactors. More than ten years from its beginning the Russian RERTR program developed practically independently from the international RERTR program and only at the begin of 90's the Russian specialists started to contact with foreign scientists and the exchange of the scientific information has become more intensive. In September 1994, representatives of Minatom and DOE signed a protocol of intent to reduce an enrichment of uranium in research reactors. The main aspects of collaboration involve: Several domestic Russian research reactors such as WWR-M, IR-8 and others were investigated from the point of view of possibility of reducing of enrichment; financial support of the program from US DOE which is insufficient. The important part of international collaboration is the import of Russian origin spent and fresh fuel of research reactors to Russia. In August 2002 an impressive result of the Russian-American collaboration with support of IAEA and with the help and assistance of Yugoslavian side was

Shipment of VINCA Institute's HEU fresh fuel to Russia

International Nuclear Information System (INIS)

Pesic, Milan; Sotic, Obrad

2002-01-01

This paper shows, for the first time, the basic data related to the recent shipment of the fresh HEU fuel elements from Yugoslavia back to Russia for uranium down blending. In this way, Yugoslavia gives its contribution to the RERTR program and to the world's joint efforts to prevent possible terrorist action against nuclear material potentially usable for production of nuclear weapons. (author)

Comparison of the FRM-II HEU design with an alternative LEU design. Attachment

International Nuclear Information System (INIS)

Hanan, N.A.; Mo, S.C.; Smith, R.S.; Matos, J.E.

2004-01-01

After presentation of the foregoing paper by Dr. Nelson Hanan of Argonne National Laboratory (ANL) proposing an alternative LEU core with one fuel ring and a power level of 33 MW, a presentation was made by Dr. Klaus Boning of the Technical University of Munich comparing the FRM-II HEU design with an LEU design by Tlm that had two fuel rings and a power level of 40 MW. Dr. Boning raised the following issues concerning the use of LEU fuel in FRM-H reactor designs: (1) qualification of HEU and LEU silicide fuels, (2) gamma heating in the heavy water reflector, (3) the radiological consequences of hypothetical accidents, and (4) cost and schedule. These issues are addressed in this Attachment. In his presentation, Dr. Hanan mentioned that ANL was also investigating other LEU designs. This work led to a second alternative LEU design that has the same neutron flux performance (8 x 10 14 n/cm 2 /s peak neutron flux in the reflector) and the same fuel lifetime (50 full power days) as the HEU design, but uses LEU silicide fuel with a uranium density of only 4.5 g/cm 3 . This design was achieved by using a fuel plate that has a fuel meat thickness of 0.76 mm, a cladding thickness of 0.38 mm, and a water channel gap of 2.2 mm. A comparison is shown of the main characteristics of this second alternative LEU design with those of the FRM-II HEU design. The ANL core again has one fuel ring with the same dimensions. With this LEU design, a two stage process is no longer necessary because LEU silicide fuel with a uranium density of 4.5 g/cm 3 is fully qualified, licensable, and available now for use in a high flux reactor such as the FRM-II

An Analysis of the HEU-MET-FAST-035 Problem Using CENTRM and SCALE

International Nuclear Information System (INIS)

Hollenbach, D.F.; Jordan, W.C.

1999-01-01

An U/Fe benchmark, designated as HEU-MET-FAST-035, has been approved for inclusion in the International Handbook of Evaluated Criticality Safety Benchmark Experiments. The SCALE code and cross sections performed poorly in calculating this critical experiment. Deficiencies in both the ENDF/B-V representation of the resonance region for Fe and in the Nordheim integral treatment when applied to Fe were identified. The combination of these deficiencies led to an almost 10% over-prediction of k(eff). Problems involving a large percentage of Fe and intermediate-energy spectrums present special cross-section processing difficulties for SCALE. In ENDF/B-V, resonance data for Fe only go to 400 keV, although resonances are present well above 1 MeV. Significant resonance data are stored as file 3 data instead of as resonance parameters. The Nordheim Integral Treatment used in NITAWL to process cross sections assume: resonances are widely spaced and all relevant information is contained in the resonance parameters (file 3 data is not processed). These limitations and assumptions result in poor solutions for this class of problems

Ohio State University Nuclear Reactor Laboratory HEU fuel shipment summary. Final

International Nuclear Information System (INIS)

1997-01-01

In November 1988, OSURR converted from HEU fuel to LEU fuel. As a result they needed to get rid of their HEU fuel by shipping it to Savannah River. The players in the fuel shipping game are: OSURR as the keeper of the fuel; DOE as the owner of fuel and shipper of record; Tri-State Motor Transit Co. for transporting the cask; Muth Brothers as the rigger responsible for getting the cask on and off the truck and in and out of the building; Hoffman LaRoche/Cintichem as the owner of the cask; Savannah River as the receiver of the fuel; and the NRC for approval of the Security Plan, QA Plan, etc. This report gives a chronological history of the events from February 1989 to June 1, 1995, the actual day of shipment. The cask was received at Savannah River on June 2, 1995

Fuel element burnup determination in HEU-LEU mixed TRIGA research reactor core

International Nuclear Information System (INIS)

Zagar, Tomaz; Ravnik, Matjaz

2000-01-01

This paper presents the results of a burnup calculations and burnup measurements for TRIGA FLIP HEU fuel elements and standard TRIGA LEU fuel elements used simultaneously in small TRIGA Mark II research reactor in Ljubljana, Slovenija. The fuel element burnup for approximately 15 years of operation was calculated with two different in house computer codes TRIGAP and TRIGLAV (both codes are available at OECD NEA Data Bank). The calculation is performed in one-dimensional radial geometry in TRIGAP and in two-dimensional (r,φ) geometry in TRIGLAV. Inter-comparison of results shows important influence of in-core water gaps, irradiation channels and mixed rings on burnup calculation accuracy. Burnup of 5 HEU and 27 LEU fuel elements was also measured with reactivity method. Measured and calculated burnup values are inter-compared for these elements (author)

Application of SN and Monte Carlo codes to the SHEBA critical assemblies

International Nuclear Information System (INIS)

O'Dell, R.D.

1993-01-01

The Solution High-Energy Burst Assembly (SHEBA) at Los Alamos is a low-enriched (4.95 wt. %) aqueous uranyl fluoride solution critical assembly. There are two SHEBA configurations, both consisting of right circular cylinders with a central control rod. The first configuration, hereafter called the old SHEBA, had a fuel solution diameter of 54.6 cm and a measured critical solution height of 36.5 cm. An improved modification, hereafter called the new SHEBA, has a fuel solution diameter of 48.9 cm but since it is not yet operational, the critical solution height has not yet been measured. In this presentation the application of the discrete-ordinates (S N ) code TWODANT using Hansen-Roach cross sections and the MCNP Monte Carlo code using continuous-energy cross sections for calculating the critical solution heights for both the old and new SHEBA assemblies is described. The code's predictions are compared and it is shown that a single calculation with a standard computer code may yield misleading results, especially when using a Monte Carlo code

Progress in the neutronic core conversion (HEU-LEU) analysis of Ghana research reactor-1.

Energy Technology Data Exchange (ETDEWEB)

Anim-Sampong, S.; Maakuu, B. T.; Akaho, E. H. K.; Andam, A.; Liaw, J. J. R.; Matos, J. E.; Nuclear Engineering Division; Ghana Atomic Energy Commission; Kwame Nkrumah Univ. of Science and Technology

2006-01-01

The Ghana Research Reactor-1 (GHARR-1) is a commercial version of the Miniature Neutron Source Reactor (MNSR) and has operated at different power levels since its commissioning in March 1995. As required for all nuclear reactors, neutronic and thermal hydraulic analysis are being performed for the HEU-LEU core conversion studies of the Ghana Research Reactor-1 (GHARR-1) facility, which is a commercial version of the Miniature Neutron Source Reactor (MNSR). Stochastic Monte Carlo particle transport methods and tools (MCNP4c/MCNP5) were used to fine-tune a previously developed 3-D MCNP model of the GHARR-1 facility and perform neutronic analysis of the 90.2% HEU reference and candidate LEU (UO{sub 2}, U{sub 3}Si{sub 2}, U-9Mo) fresh cores with varying enrichments from 12.6%-19.75%. In this paper, the results of the progress made in the Monte Carlo neutronic analysis of the HEU reference and candidate LEU fuels are presented. In particular, a comparative performance assessment of the LEU with respect to neutron flux variations in the fission chamber and experimental irradiation channels are highlighted.

Neutronic analysis of the conversion of HEU to LEU fuel for a 5-MW MTR core

International Nuclear Information System (INIS)

Pazirandeh, A.; Bartsch, G.

1987-01-01

In recent years, due to cessation of highly enriched uranium (HEU) fuel supply, practical steps have been taken to substitute HEU fuel in almost all research reactors by medium-enriched uranium or low-enriched uranium (LEU) fuels. In this study, a neutronic calculation of a 5-MW research reactor core fueled with HEU (93% 235 U) is presented. In order to assess the performance of the core with the LEU ( 235 U loadings were examined. The core consists of 22 standard fuel elements (SFEs) and 6 control fuel elements (CFEs). Each fuel elements has 18 curved plates of which two end plates are dummies. Initial 235 U content is 195 g 235 U/SFE and 9.7 g 235 U/CFE or /PFE. In all calculations the permitted changes to the fuel elements are (a) 18 active plates per SFE, (b) fuel plates assumed to be flat, and (c) 8 or 9 active plates per CFE

HEU to LEU Conversion and Blending Facility: UF6 blending alternative to produce LEU UF6 for commercial use

International Nuclear Information System (INIS)

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials; the nuclear material will be converted to a form more proliferation- resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. Five technologies for blending HEU will be assessed; blending as UF 6 to produce a UF 6 product for commercial use is one of them. This document provides data to be used in the environmental impact analysis for the UF 6 blending HEU disposition option. Resource needs, employment needs, waste and emissions from plant, hazards, accident scenarios, and intersite transportation are discussed

Comparison of HEU and LEU neutron spectra in irradiation facilities at the Oregon State TRIGA{sup ®} Reactor

Energy Technology Data Exchange (ETDEWEB)

Schickler, R.A., E-mail: robert.schickler@oregonstate.edu; Marcum, W.R., E-mail: wade.marcum@oregonstate.edu; Reese, S.R.

2013-09-15

Highlights: • The Oregon State TRIGA{sup ®} Reactor neutron spectra is characterized herein. • Neutron spectra between highly enriched uranium and low enriched uranium cores are compared. • Discussion is given as to differences between HEU and LEU core spectra results and impact on experiments. -- Abstract: In 2008, the Oregon State TRIGA{sup ®} Reactor (OSTR) was converted from highly enriched uranium (HEU) fuel lifetime improvement plan (FLIP) fuel to low-enriched uranium (LEU) fuel. This effort was driven and supported by the Department of Energy's (DoE's) Reduced Enrichment for Research and Test Reactors (RERTR) program. The basis behind the RERTR program's ongoing conversion effort is to reduce the nuclear proliferation risk of civilian research and test reactors. The original intent of the HEU FLIP fuel was to provide fuel to research reactors that could be utilized for many years before a necessary refueling cycle. As a research reactor, the OSTR provides irradiation facilities for a variety of applications, such as activation analysis, fission-track dating, commercial isotope production, neutron radiography, prompt gamma characterization, and many others. In order to accurately perform these research functions, several studies had been conducted on the HEU FLIP fuel core to characterize the neutron spectra in various experimental facilities of the OSTR (Tiyapun, 1997; Ashbaker, 2005). As useful as these analyses were, they are no longer valid due to the change in fuel composition and the resulting alteration of core performance characteristics. Additionally, the core configuration (fuel reconfiguration) was altered between the HEU and LEU cores. This study characterizes the neutron spectra in various experimental facilities within and around the current LEU core. It also compares the spectra to that which was yielded in the HEU core through use of Monte Carlo n-Particle 5 (MCNP5) and experimental adjustment via a least

The ORSphere Benchmark Evaluation and Its Potential Impact on Nuclear Criticality Safety

Energy Technology Data Exchange (ETDEWEB)

John D. Bess; Margaret A. Marshall; J. Blair Briggs

2013-10-01

In the early 1970’s, critical experiments using an unreflected metal sphere of highly enriched uranium (HEU) were performed with the focus to provide a “very accurate description…as an ideal benchmark for calculational methods and cross-section data files.” Two near-critical configurations of the Oak Ridge Sphere (ORSphere) were evaluated as acceptable benchmark experiments for inclusion in the International Handbook of Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook). The results from those benchmark experiments were then compared with additional unmoderated and unreflected HEU metal benchmark experiment configurations currently found in the ICSBEP Handbook. For basic geometries (spheres, cylinders, and slabs) the eigenvalues calculated using MCNP5 and ENDF/B-VII.0 were within 3 of their respective benchmark values. There appears to be generally a good agreement between calculated and benchmark values for spherical and slab geometry systems. Cylindrical geometry configurations tended to calculate low, including more complex bare HEU metal systems containing cylinders. The ORSphere experiments do not calculate within their 1s uncertainty and there is a possibility that the effect of the measured uncertainties for the GODIVA I benchmark may need reevaluated. There is significant scatter in the calculations for the highly-correlated ORCEF cylinder experiments, which are constructed from close-fitting HEU discs and annuli. Selection of a nuclear data library can have a larger impact on calculated eigenvalue results than the variation found within calculations of a given experimental series, such as the ORCEF cylinders, using a single nuclear data set.

Criticality safety evaluation for the Advanced Test Reactor enhanced low enriched uranium fuel elements

Energy Technology Data Exchange (ETDEWEB)

Montierth, Leland M. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-07-19

The Global Threat Reduction Initiative (GTRI) convert program is developing a high uranium density fuel based on a low enriched uranium (LEU) uranium-molybdenum alloy. Testing of prototypic GTRI fuel elements is necessary to demonstrate integrated fuel performance behavior and scale-up of fabrication techniques. GTRI Enhanced LEU Fuel (ELF) elements based on the ATR-Standard Size elements (all plates fueled) are to be fabricated for testing in the Advanced Test Reactor (ATR). While a specific ELF element design will eventually be provided for detailed analyses and in-core testing, this criticality safety evaluation (CSE) is intended to evaluate a hypothetical ELF element design for criticality safety purposes. Existing criticality analyses have analyzed Standard (HEU) ATR elements from which controls have been derived. This CSE documents analysis that determines the reactivity of the hypothetical ELF fuel elements relative to HEU ATR elements and whether the existing HEU ATR element controls bound the ELF element. The initial calculations presented in this CSE analyzed the original ELF design, now referred to as Mod 0.1. In addition, as part of a fuel meat thickness optimization effort for reactor performance, other designs have been evaluated. As of early 2014 the most current conceptual designs are Mk1A and Mk1B, that were previously referred to as conceptual designs Mod 0.10 and Mod 0.11, respectively. Revision 1 evaluates the reactivity of the ATR HEU Mark IV elements for a comparison with the Mark VII elements.

Criticality safety evaluation for the Advanced Test Reactor enhanced low enriched uranium fuel elements

International Nuclear Information System (INIS)

Montierth, Leland M.

2016-01-01

The Global Threat Reduction Initiative (GTRI) convert program is developing a high uranium density fuel based on a low enriched uranium (LEU) uranium-molybdenum alloy. Testing of prototypic GTRI fuel elements is necessary to demonstrate integrated fuel performance behavior and scale-up of fabrication techniques. GTRI Enhanced LEU Fuel (ELF) elements based on the ATR-Standard Size elements (all plates fueled) are to be fabricated for testing in the Advanced Test Reactor (ATR). While a specific ELF element design will eventually be provided for detailed analyses and in-core testing, this criticality safety evaluation (CSE) is intended to evaluate a hypothetical ELF element design for criticality safety purposes. Existing criticality analyses have analyzed Standard (HEU) ATR elements from which controls have been derived. This CSE documents analysis that determines the reactivity of the hypothetical ELF fuel elements relative to HEU ATR elements and whether the existing HEU ATR element controls bound the ELF element. The initial calculations presented in this CSE analyzed the original ELF design, now referred to as Mod 0.1. In addition, as part of a fuel meat thickness optimization effort for reactor performance, other designs have been evaluated. As of early 2014 the most current conceptual designs are Mk1A and Mk1B, that were previously referred to as conceptual designs Mod 0.10 and Mod 0.11, respectively. Revision 1 evaluates the reactivity of the ATR HEU Mark IV elements for a comparison with the Mark VII elements.

Subchannel analysis of a critical power test, using simulated BWR 8x8 fuel assembly

International Nuclear Information System (INIS)

Mitsutake, T.; Terasaka, H.; Yoshimura, K.; Oishi, M.; Inoue, A.; Akiyama, M.

1990-01-01

Critical power predictions have been compared with the critical power test data obtained in simulated BWR 8x8 fuel rod assemblies. Two analytical methods for the critical power prediction in rod assemblies are used in the prediction, which are the subchannel analysis using the COBRA/BWR subchannel computer code with empirical critical heat flux (CHF) correlations and the liquid film dryout estimation using the CRIPP-3F 'multi-fluid' computer code. Improvements in both the analytical methods were made for spacer effect modeling, though they were specific for application to the current BWR rod assembly type. In general a reasonable agreement was obtained, though comparisons, between the prediction and the obtained test data. (orig.)

Highly enriched uranium (HEU) politics: An enigma wrapped up in a warhead and boxed in political chaos

International Nuclear Information System (INIS)

Anon.

1993-01-01

It could be fairly said that while the Cold War arose in an atmosphere of mutual mistrust and hostility, it is ending with an equal amount of confusion and uncertainty. More than a year has passed since the US and Russia signed a tentative HEU agreement in August 1992. Many of the details have been worked out, but major questions remain. And they're not just on the Russian side. The fine points of President Clinton's overall nuclear policy are only now beginning to emerge. In his first major foreign policy address, before the United Nations in late September, Clinton called for a worldwide ban on the production of plutonium and HEU for nuclear weapons. open-quotes Growing global stockpiles of plutonium and highly enriched uranium are raising the danger of nuclear terrorism for all nations,close quotes said Clinton before the UN. open-quotes We will press for an international agreement that would ban production of these materials for weapons forever.close quotes As the veil lifts from Clinton's nuclear policy, it appears the Administration realizes that Russia may have more HEU than originally thought. That possibility has been confirmed by Minatom Minister Mikhailov's disclosures to the NUKEM Market Report, which brought a greater degree of certainty to estimates that had been floating around for some time. When the Bush Administration signed the HEU pact, it apparently thought the 500 metric tons comprised most of the former Soviet Union's nuclear arsenal. Now that the number appears higher, Clinton may propose to accelerate and enlarge the HEU deal. He is due to summit with Yeltsin, if Yeltsin survives, next spring. The 500-metric-ton deal may only be the first step

A comparison of the radiological consequences of a HEU and LEU fueled research reactor

International Nuclear Information System (INIS)

Kollas, J.G.

1985-01-01

An analysis of the design basis accident radiological consequences of the HEU and LEU fueled Greek Research Reactor is presented. Doses and individual cancer risk from exposure to the passing radioactive cloud are estimated up to a distance of 20 km from the reactor site. Collective exposure and latent health effects are estimated for the total Athens area of 3081000 inhabitants. The results indicate that the plutonium isotopes buildup in the LEU fuel does not increase appreciably the consequences in respect to the HEU fueled reactor. The plutonium impact concerns mainly bone effects and secondly lung and whole body effects. The contribution to the limiting thyroid dose and the corresponding thyroid effects is insignificant. (author)

An improved benchmark model for the Big Ten critical assembly - 021

International Nuclear Information System (INIS)

Mosteller, R.D.

2010-01-01

A new benchmark specification is developed for the BIG TEN uranium critical assembly. The assembly has a fast spectrum, and its core contains approximately 10 wt.% enriched uranium. Detailed specifications for the benchmark are provided, and results from the MCNP5 Monte Carlo code using a variety of nuclear-data libraries are given for this benchmark and two others. (authors)

Operation of automated NDA instruments for in-line HEU accounting at Y-12

International Nuclear Information System (INIS)

Russo, P.A.; Strittmatter, R.B.; Sandford, E.L.; Jeter, I.W.; McCullough, E.; Bowers, G.L.

1983-01-01

Two automated nondestructive assay instruments developed at Los Alamos in support of nuclear materials accounting needs are currently operating in-line at the Y-12 Plant for recovery of highly enriched uranium. One instrument provides the HEU inventory in the secondary solvent extraction system, and the other monitors HEU concentration in the secondary intermediate evaporator. Both instruments were installed in December 1982. Operational evaluation of these instruments has been a joint effort of Y-12 and Los Alamos. This has included comparison of the solvent extraction system inventories with direct measurement performed on the dumped solution components of the solvent extraction system, as well as comparisons of concentration assay results with the external assays of samples withdrawn from the process. The function, design, and preliminary results of the operational evaluation are reported

Critical experiments of JMTRC MEU cores

International Nuclear Information System (INIS)

Nagaoka, Y.; Takeda, K.; Shimakawa, S.; Koike, S.; Oyamada, R.

1984-01-01

The JMTRC, the critical facility of the Japan Materials Testing Reactor (JMTR), went critical on August 29, 1983, with 14 medium enriched uranium (MEU, 45%) fuel elements. Experiments are now being carried out to measure the change in various reactor characteristics between the previous HEU core and the new MEU fueled core. This paper describes the results obtained thus far on critical mass, excess reactivity, control rod worths and flux distribution, including preliminary neutronics calculations for the experiments using the SRAC code. (author)

Multilateral nonproliferation cooperation: US - Led effort to remove HEU/LEU fresh and spent fuels from the Republic of Georgia to Dounreay, Scotland

International Nuclear Information System (INIS)

Shelton, Thomas A.; Viebrock, James M.; Riedy, Alexander W.; Moses, Stanley D.; Bird, Helen M.

1998-01-01

This paper presents the efforts led by United States for removing HEU/LEU fresh and spent fuel from dhe Republic of Georgia to Dounreay, Scotland. These efforts are resulted from a plan approved by the United States Government, in cooperation with the United Kingdom and Georgia Governments to rapidly retrieve and transport circa 4.3 kilograms of enriched uranium. This material consisted largely of highly enriched uranium (HEU) and a small amount of low enriched uranium (LEU) fresh fuel, as well as about 800 grams of HEU/LEU-based spent fuel from a shutdown IR T-M research reactor on the outskirts of Table's, Georgia. The technical team lead by DOE consisted of HEU handling, packaging and transportation experts from the Oak Ridge Y-12 plant, managed and operated by Lockheed Martin Energy Systems, and fuel handling and transportation experts from Nac International in Norcross, Georgia, United States

Coordination Between the HEU Transparency Program and the Material Protection, Control and Accountability Program

International Nuclear Information System (INIS)

Glaser, J.; Hernandez, J.; Dougherty, D.; Bieniawski, A.; Cahalane, P.; Mastal, E.

2000-01-01

DOE sponsored programs such as Material Protection Control and Accountability (MPC and A) and implementation of the Highly-Enriched Uranium (HEU) Transparency Program send US personnel into Russian nuclear facilities and receive Russian representatives from these programs. While there is overlap in the Russian nuclear facilities visited by these two programs, there had not been any formal mechanism to share information between them. Recently, an MPC and A/HEU Working Group was developed to facilitate the sharing of appropriate information and to address concerns expressed by Minatom and Russian facility personnel such as US visit scheduling conflicts. This paper discusses the goals of the Working Group and ways it has helped to allow the programs to work more efficiently with the Russian facilities

Benchmark calculations on nuclear characteristics of JRR-4 HEU core by SRAC code system

International Nuclear Information System (INIS)

Arigane, Kenji

1987-04-01

The reduced enrichment program for the JRR-4 has been progressing based on JAERI's RERTR (Reduced Enrichment Research and Test Reactor) program. The SRAC (JAERI Thermal Reactor Standard Code System for Reactor Design and Analysis) is used for the neutronic design of the JRR-4 LEU Core. This report describes the benchmark calculations on the neutronic characteristics of the JRR-4 HEU Core in order to validate the calculation method. The benchmark calculations were performed on the various kind of neutronic characteristics such as excess reactivity, criticality, control rod worth, thermal neutron flux distribution, void coefficient, temperature coefficient, mass coefficient, kinetic parameters and poisoning effect by Xe-135 build up. As the result, it was confirmed that these calculated values are in satisfactory agreement with the measured values. Therefore, the calculational method by the SRAC was validated. (author)

Kinetic analysis of sub-prompt-critical reactor assemblies

International Nuclear Information System (INIS)

Das, S.

1992-01-01

Neutronic analysis of safety-related kinetics problems in experimental neutron multiplying assemblies has been carried out using a sub-prompt-critical reactor model. The model is based on the concept of a sub-prompt-critical nuclear reactor and the concept of instantaneous neutron multiplication in a reactor system. Computations of reactor power, period and reactivity using the model show excellent agreement with results obtained from exact kinetics method. Analytic expressions for the energy released in a controlled nuclear power excursion are derived. Application of the model to a Pulsed Fast Reactor gives its sensitivity between 4 and 5. (author). 6 refs., 4 figs., 1 tab

HEU to LEU Conversion and Blending Facility: UF{sub 6} blending alternative to produce LEU UF{sub 6} for commercial use

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

US DOE is examining options for disposing of surplus weapons-usable fissile materials and storage of all weapons-usable fissile materials; the nuclear material will be converted to a form more proliferation- resistant than the original form. Examining options for increasing the proliferation resistance of highly enriched uranium (HEU) is part of this effort. Five technologies for blending HEU will be assessed; blending as UF{sub 6} to produce a UF{sub 6} product for commercial use is one of them. This document provides data to be used in the environmental impact analysis for the UF{sub 6} blending HEU disposition option. Resource needs, employment needs, waste and emissions from plant, hazards, accident scenarios, and intersite transportation are discussed.

Physical and geometrical parameters of ANNA critical assemblies. Pt. 2

International Nuclear Information System (INIS)

Malewski, S.; Dabrowski, C.

1973-01-01

An extended analysis of four critical configurations of ANNA Assembly has been performed. Diffusion parameters of the thermal group and of one or three epithermal groups have been determined. Using these data the critical calculations have been carried out and the main neutron density distributions presented. The role of some neutron processes in these systems and their influence on integral parameters has been considered. The calculated quantities have been compared with the available experimental data. (author)

Energy–angle correlation of neutrons and gamma-rays emitted from an HEU source

Energy Technology Data Exchange (ETDEWEB)

Miloshevsky, G., E-mail: gennady@purdue.edu; Hassanein, A.

2014-06-01

Special Nuclear Materials (SNM) yield very unique fission signatures, namely correlated neutrons and gamma-rays. A major challenge is not only to detect, but also to rapidly identify and recognize SNM with certainty. Accounting for particle multiplicity and correlations is one of standard ways to detect SNM. However, many parameter data such as joint distributions of energy, angle, lifetime, and multiplicity of neutrons and gamma-rays can lead to better recognition of SNM signatures in the background radiation noise. These joint distributions are not well understood. The Monte Carlo simulations of the transport of neutrons and gamma-rays produced from spontaneous and interrogation-induced fission of SNM are carried out using the developed MONSOL computer code. The energy spectra of neutrons and gamma-rays from a bare Highly Enriched Uranium (HEU) source are investigated. The energy spectrum of gamma-rays shows spectral lines by which HEU isotopes can be identified, while those of neutrons do not show any characteristic lines. The joint probability density function (JPDF) of the energy–angle association of neutrons and gamma-rays is constructed. Marginal probability density functions (MPDFs) of energy and angle are derived from JPDF. A probabilistic model is developed for the analysis of JPDF and MPDFs. This probabilistic model is used to evaluate mean values, standard deviations, covariance and correlation between the energy and angle of neutrons and gamma-rays emitted from the HEU source. For both neutrons and gamma-rays, it is found that the energy–angle variables are only weakly correlated.

Research and design calculation of multipurpose critical assembly using moderated light water and low enriched fuel from 1.6 to 5.0% U-235

International Nuclear Information System (INIS)

Nguyen Kien Cuong; Vo Doan Hai Dang; Luong Ba Vien; Le Vinh Vinh; Huynh Ton Nghiem; Nguyen Minh Tuan; Nguyen Manh Hung; Pham Quang Huy; Tran Quoc Duong; Tran Tri Vien

2015-01-01

Basing on the idea in ??using fuel of nuclear power plants such as PWR (AP-1000) and VVER-1000 with light water as moderation, design calculation of critical assembly was performed to confirm the possibility of using these fuels. Designed critical assembly has simple structure consisting of low enriched fuel from 1.6% to 5% U-235; water has functions as cooling, biological protection and control. Critical assembly is operated at nominal power 100 W with fuel pitch about 2.0 cm. Applications of the critical assembly are quite abundant in basic research, education and training with low investment cost compare with research reactor and easy in operation. So critical assembly can be used for university or training centre for nuclear engineering training. Main objectives of the project are: design calculation in neutronics, thermal hydraulics and safety analysis for critical configuration benchmarks using low enriched fuel; design in mechanical and auxiliary systems for critical assembly; determine technical specifications and estimate construction, installation cost of critical assembly. The process of design, fabrication, installation and construction of critical assembly will be considered with different implementation phases and localization capabilities in installation of critical assembly is highly feasibility. Cost estimation of construction and installation of critical assembly was implemented and showed that investment cost for critical assembly is much lower than research reactor and most of components, systems of critical assembly can be localized with current technique quality of the country. (author)

Systems analysis determining critical items, critical assembly processes, primary failure modes and corrective actions on ASST magnets

International Nuclear Information System (INIS)

Arden, C.S.

1993-04-01

During the assembly process through the completion of the Accelerator Surface String Test (ASST) phase one test, Magnet Systems Division Reliability Engineering has tracked all the known discrepancies utilizing the Failure Reporting, Analysis and Corrective Action System (FRACAS) and data base. This paper discusses the critical items, critical assembly processes, primary failure modes and corrective actions (lessons learned) based on actual data for the ASST magnets. The ASST magnets include seven Brookhaven Lab Dipoles (DCA-207 through 213), fourteen Fermi Lab Dipoles (DCA-310 through 323) and five Lawrence Berkeley Lab Quadrupoles (QCC-402 through 406). Between all the ASST magnets built there were one hundred eighty six (186) class one discrepancies reported out of approximately eleven hundred total discrepancy reports. The class one or critical discrepancies are defined as form, fit, function, safety or reliability problem. Each and every ASST magnet is considered a success, as they all achieved the quench performance requirements and were capable of being incorporated into the string test. This paper also discuss some specific magnet discrepancies, including failure cause(s), corrective action and possible open issues

Systems analysis determining critical items, critical assembly processes, primary failure modes and corrective actions on ASST magnets

International Nuclear Information System (INIS)

Arden, C.S.

1994-01-01

During the assembly process through the completion of the Accelerator Surface String Test (ASST) phase one test, Magnet Systems Division Reliability Engineering has tracked all the known discrepancies utilizing the Failure Reporting, Analysis and Corrective Action System (FRACAS) and data base. This paper discusses the critical items, critical assembly processes, primary failure modes and corrective actions (lessons learned) based on actual data for the ASST magnets. The ASST magnets include seven Brookhaven Lab Dipoles (DCA-207 through 213), fourteen Fermi Lab Dipoles (DCA-310 through 323) and five Lawrence Berkeley Lab Quadrupoles (QCC-402 through 406). Between all the ASST magnets built there were one hundred eighty six (186) class one discrepancies reported out of approximately eleven hundred total discrepancy reports. The class one or critical discrepancies are defined as form, fit, function, safety or reliability problem. Each and every ASST magnet is considered a success, as they all achieved the quench performance requirements and were capable of being incorporated into the string test. This paper will also discuss some specific magnet discrepancies, including failure cause(s), corrective action and possible open issues

The status of HEU and LEU core conversion activities at the Jamaica SLOWPOKE

Energy Technology Data Exchange (ETDEWEB)

Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Kingston (Jamaica)

2013-07-01

The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, inline with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

Foreign research reactor spent nuclear fuel inventories containing HEU and LEU of US-origin

International Nuclear Information System (INIS)

Matos, J.E.

1995-01-01

This paper provides estimates of the quantities and types of foreign research reactor spent nuclear fuel containing HEU and LEU of US-origin that are anticipated during the period beginning in January 1996 and extending for 10-15 years

A re-evaluation of physical protection standards for irradiated HEU fuel

International Nuclear Information System (INIS)

Lyman, Edwin; Kuperman, Alan

2002-01-01

In the post-September 11 era, it is essential to reconsider all the assumptions upon which the physical protection systems of the past were based and determine whether these assumptions are still appropriate in light of the current terrorist threat. For instance, the U.S. Nuclear Regulatory Commission definition of a 'formula quantity' of special nuclear material is derived from the belief that a terrorist plot to carry out multiple coordinated attacks on different facilities with the goal of acquiring enough SNM for a nuclear weapon is incredible. This assumption has clearly been proven wrong by the September 11 attacks. Another standard that needs to be revisited is the 'self-protection' threshold that determines whether or not an item containing SNM is considered to be 'irradiated' for physical protection purposes. The current value of this threshold, 1 Sv/hr unshielded at 1 meter, is of questionable value as a deterrent to determined terrorists who would be willing to sustain long-term injury as long as they could accomplish their near-term goals. A more credible threshold would be set at a level that would have a high likelihood of disabling the perpetrators before they could complete their mission. Most irradiated nonpower reactor fuels would be unable to meet such a standard. This raises serious questions about the adequacy of the level of physical protection applied today to the large inventories of irradiated HEU fuels now scattered in storage sites around the world. The absence of a coherent global policy for dealing with these materials has created a situation rife with vulnerabilities that terrorists could exploit. The international community, now seized with concern about unused stockpiles of unirradiated HEU fuels around the world, also needs to appreciate the dangers posed by lightly irradiated spent fuels as well. A U.S. proposal to import Russian HEU for supplying U.S. nonpower reactors will only prolong this situation This paper will review policy

ZPR-3 Assembly 11: A cylindrical sssembly of highly enriched uranium and depleted uranium with an average 235U enrichment of 12 atom % and a depleted uranium reflector

International Nuclear Information System (INIS)

Lell, R.M.; McKnight, R.D.; Tsiboulia, A.; Rozhikhin, Y.

2010-01-01

Specificationsa and has historically been used as a data validation benchmark assembly. Loading of ZPR-3 Assembly 11 began in early January 1958, and the Assembly 11 program ended in late January 1958. The core consisted of highly enriched uranium (HEU) plates and depleted uranium plates loaded into stainless steel drawers, which were inserted into the central square stainless steel tubes of a 31 x 31 matrix on a split table machine. The core unit cell consisted of two columns of 0.125 in.-wide (3.175 mm) HEU plates, six columns of 0.125 in.-wide (3.175 mm) depleted uranium plates and one column of 1.0 in.-wide (25.4 mm) depleted uranium plates. The length of each column was 10 in. (254.0 mm) in each half of the core. The axial blanket consisted of 12 in. (304.8 mm) of depleted uranium behind the core. The thickness of the depleted uranium radial blanket was approximately 14 in. (355.6 mm), and the length of the radial blanket in each half of the matrix was 22 in. (558.8 mm). The assembly geometry approximated a right circular cylinder as closely as the square matrix tubes allowed. According to the logbook and loading records for ZPR-3/11, the reference critical configuration was loading 10 which was critical on January 21, 1958. Subsequent loadings were very similar but less clean for criticality because there were modifications made to accommodate reactor physics measurements other than criticality. Accordingly, ZPR-3/11 loading 10 was selected as the only configuration for this benchmark. As documented below, it was determined to be acceptable as a criticality safety benchmark experiment. A very accurate transformation to a simplified model is needed to make any ZPR assembly a practical criticality-safety benchmark. There is simply too much geometric detail in an exact (as-built) model of a ZPR assembly, even a clean core such as ZPR-3/11 loading 10. The transformation must reduce the detail to a practical level without masking any of the important features of the critical

Influence of “whirlwind” mixing grids on the critical power of WWER fuel assembly

International Nuclear Information System (INIS)

Selivanov, Yu.F.; Pomet'ko, R.S.; Volkov, S.E.

2014-01-01

The problem of optimizing the number and placement of lattices in different types assemblies is discussed. The effect of the amount of mixing lattices and their locations in assemblies on the conditions of occurrence of boiling crisis in the fuel assembly on its critical power (power of assembly in case of boiling crisis) is studied. Experiments were carried out with the use of freon as a coolant. It is recommended simultaneous use in the assembly of lattices of “whirlwind” type, well-intensifying heat exchange, and cell lattices of “pass” type (or lattices with deflectors) affecting on moving flow, provided the optimal location of lattices in the assembly [ru

Safety analysis report for the Hanford Critical Mass Laboratory: Supplement No. 2. Experiments with heterogeneous assemblies

International Nuclear Information System (INIS)

Gore, B.F.; Davenport, L.C.

1981-04-01

Factors affecting the safety of criticality experiments using heterogeneous assemblies are described and assessed. It is concluded that there is no substantial change in safety from experiments already being routinely performed at the Critical Mass Laboratory (CML), and that laboratory and personnel safety are adequately provided by the combination of engineered and administrative safety limits enforced at the CML. This conclusion is based on the analysis of operational controls, potential hazards, and the consequences of accidents. Contingencies considered that could affect nuclear criticality include manual changes in fuel loadings, water flooding, fire, explosion, loss of services, earthquake, windstorm, and flood. Other potential hazards considered include radiation exposure to personnel, and potential releases within the Assembly Room and outside to the environment. It is concluded that the Maximum Credible Nuclear Burst of 3 x 10 18 fissions (which served as the design basis for the CML) is valid for heterogeneous assemblies as well as homogeneous assemblies. This is based upon examination of the results of reactor destructive tests and the results of the SL-1 reactor destructive accident. The production of blast effects which might jeopardize the CML critical assembly room (of thick reinforced concrete) is not considered credible due to the extreme circumstances required to produce blast effects in reactor destructive tests. Consequently, it is concluded that, for experiments with heterogeneous assemblies, the consequences of the Maximum Credible Burst are unchanged from those previously estimated for experiments with homogeneous systems

Knowledge Transfer and Culture Exchange between HEU and TAMU through a Summer School on Nuclear Power Engineering

International Nuclear Information System (INIS)

Gao, P.; Zhang, Z.; Kurwitz, R. C.; Shao, L.

2016-01-01

Full text: Since 2012, Harbin Engineering University (HEU) and Texas A&M University (TAMU) hold an annual Summer School on Nuclear Engineering. By now, the activity has been held four times. Each year, 15–20 students are selected from their respective institutions and paired with a counterpart to form partners. They study lectures in the first week at HEU and tour three nuclear power plants (NPP) in the second week, visit the NPP simulators, and learn the nuclear safety culture. This activity expands the scale of international nuclear educational exchange, provide a platform for the students from different countries to communicate and exchange insights into their respective culture. (author

ZPR-3 Assembly 11 : A cylindrical sssembly of highly enriched uranium and depleted uranium with an average {sup 235}U enrichment of 12 atom % and a depleted uranium reflector.

Energy Technology Data Exchange (ETDEWEB)

Lell, R. M.; McKnight, R. D.; Tsiboulia, A.; Rozhikhin, Y.; National Security; Inst. of Physics and Power Engineering

2010-09-30

Working Group (CSEWG) Benchmark Specificationsa and has historically been used as a data validation benchmark assembly. Loading of ZPR-3 Assembly 11 began in early January 1958, and the Assembly 11 program ended in late January 1958. The core consisted of highly enriched uranium (HEU) plates and depleted uranium plates loaded into stainless steel drawers, which were inserted into the central square stainless steel tubes of a 31 x 31 matrix on a split table machine. The core unit cell consisted of two columns of 0.125 in.-wide (3.175 mm) HEU plates, six columns of 0.125 in.-wide (3.175 mm) depleted uranium plates and one column of 1.0 in.-wide (25.4 mm) depleted uranium plates. The length of each column was 10 in. (254.0 mm) in each half of the core. The axial blanket consisted of 12 in. (304.8 mm) of depleted uranium behind the core. The thickness of the depleted uranium radial blanket was approximately 14 in. (355.6 mm), and the length of the radial blanket in each half of the matrix was 22 in. (558.8 mm). The assembly geometry approximated a right circular cylinder as closely as the square matrix tubes allowed. According to the logbook and loading records for ZPR-3/11, the reference critical configuration was loading 10 which was critical on January 21, 1958. Subsequent loadings were very similar but less clean for criticality because there were modifications made to accommodate reactor physics measurements other than criticality. Accordingly, ZPR-3/11 loading 10 was selected as the only configuration for this benchmark. As documented below, it was determined to be acceptable as a criticality safety benchmark experiment. A very accurate transformation to a simplified model is needed to make any ZPR assembly a practical criticality-safety benchmark. There is simply too much geometric detail in an exact (as-built) model of a ZPR assembly, even a clean core such as ZPR-3/11 loading 10. The transformation must reduce the detail to a practical level without masking any of

Spatial kinetics studies in liquid-metal fast breeder reactor critical assemblies

International Nuclear Information System (INIS)

Brumback, S.B.; Goin, R.W.; Carpenter, S.G.

1988-01-01

Recent measurements in the zero-power physics reactor have been used to study the effect of spatial decoupling in fast reactor critical assemblies of various sizes and compositions. Flux distributions in these assemblies had varying degrees of sensitivity to perturbations. Decoupling was investigated using rod-drop, boron-oscillator, and noise-coherence techniques, which emphasized different times following perturbations. Equilibrium flux distributions were also measured for subcritical configurations with inserted control rods. For most assemblies, accurate reactivity measurements were obtained by analyzing the power history from a single detector using inverse kinetics methods, assuming an instantaneous efficiency change for the detector. The instantaneous efficiency change assumption broke down, however, in assemblies with zones in which normal plutonium fuel was replaced by /sup 235/U fuel or fuel with a high /sup 240/Pu content. Flux redistributions caused by perturbations in these cores took several minutes to evolve

Fluxes at experiment facilities in HEU and LEU designs for the FRM-II

International Nuclear Information System (INIS)

Hanan, N. A.

1998-01-01

An Alternative LEU Design for the FRM-II proposed by the RERTR Program at Argonne National Laboratory (ANL) has a compact core consisting of a single fuel element that uses LEU silicide fuel with a uranium density of 4.5 g/cm 3 and has a power level of 32 MW. Both the HEU design by the Technical University of Munich (TUM) and the alternative LEU design by ANL have the same fuel lifetime(50 days) and the same neutron flux performance (8 x 10 14 n/cm 2 -s in the reflector). LEU silicide fuel with 4.5 g/cm 3 has been thoroughly tested and is fully-qualified, licensable, and available now for use in a high flux reactor such as the FRM-II. Several issues that were raised by TUM have been addressed in Refs. 1-3. The conclusions of these analyses are summarized below. This paper addresses four additional issues that have been raised in several forums, including Ref 4: heat generation in the cold neutron source (CNS), the gamma and fast neutron fluxes which are components of the reactor noise in neutron scattering experiments in the experiment hall of the reactor, a fuel cycle length difference, and the reactivity worth of the beam tubes and other experiment facilities. The results show that: (a) for the same thermal neutron flux, the neutron and gamma heating in the CNS is smaller in the LEU design than in the HEU design, and cold neutron fluxes as good or better than those of the HEU design can be obtained with the LEU design; (b) the gamma and fast neutron components of the reactor noise in the experiment hall are about the same in both designs; (c) the fuel cycle length is 50 days for both designs; and (d) the absolute value of the reactivity worth of the beam tubes and other experiment facilities is smaller in the LEU design, allowing its fuel cycle length to be increased to 53 or 54 days. Based on the excellent results for the Alternative LEU Design that were obtained in all analyses, the RERTR Program reiterates its conclusion that there are no major technical

A comparative and predictive study of the annual fuel cycle costs for HEU and LEU fuels in the High Flux Reactor, Petten, 1985-1993

Energy Technology Data Exchange (ETDEWEB)

Moss, R L; May, P

1985-07-01

The internationally agreed constraint on availability of supply of HEU fuels to Research and Test Reactors has necessitated that a cost analysis be carried out to determine the financial effect of converting the core of the HFR from HEU to LEU fuels. A computer program, written at Petten and based on information extracted from studies in Europe and the USA, identifies the major cost variables to be manufacturing, uranium, reprocessing and transport costs. Comparison between HEU and LEU cores have been carried out and includes the effects of inflation and exchange rate fluctuations. Conversion of the HFR core to LEU fuels is shown to be financially disadvantageous. (author)

A comparative and predictive study of the annual fuel cycle costs for HEU and LEU fuels in the High Flux Reactor, Petten, 1985-1993

International Nuclear Information System (INIS)

Moss, R.L.; May, P.

1985-01-01

The internationally agreed constraint on availability of supply of HEU fuels to Research and Test Reactors has necessitated that a cost analysis be carried out to determine the financial effect of converting the core of the HFR from HEU to LEU fuels. A computer program, written at Petten and based on information extracted from studies in Europe and the USA, identifies the major cost variables to be manufacturing, uranium, reprocessing and transport costs. Comparison between HEU and LEU cores have been carried out and includes the effects of inflation and exchange rate fluctuations. Conversion of the HFR core to LEU fuels is shown to be financially disadvantageous. (author)

Disposition of Highly Enriched Uranium (HEU) and Pu from nuclear weapons

International Nuclear Information System (INIS)

Neff, T.L.

1992-01-01

Last year, as the Soviet Union began to crumble and the Bush-Gorbachev talks had advanced to consider the dismantling of actual warheads instead of mere delivery systems, Dr. Thomas L. Neff, a senior member of MIT's Center for International Studies, tinkered with the notion that one day soon the US could be buying Russian uranium from scrapped nuclear arms. He also considered the costly business of dismantlement and set to work on an ingenious proposal. The basic idea was simply to purchase the HEU from Russia using funds derived from savings in the US Department of Energy's enrichment enterprise. The proposal, now part of an umbrella agreement between the US and Russia announced in early September, promises large strategic benefits for the US in terms of both financing dismantlement (to the tune of $100 million annually), as well as political oversight for the operation itself. In the words of Dr. Neff, who made briefings to both governments on the proposal, open-quotes It's a budget-neutral, win-win solution.close quotes What follows is an illustrated, step-by-step analysis of the proposal, as well as a reprint of Dr. Neff's paper, Disposition of HEU and Pu from Nuclear Weapons, as presented to the Uranium Institute's annual symposium last month

Sealing of process valves for the HEU downblending verification experiment at Portsmouth

International Nuclear Information System (INIS)

Baldwin, G.T.; Bartberger, J.C.; Jenkins, C.D.; Perlinski, A.W.; Schoeneman, J.L.; Gordon, D.M.; Whiting, N.E.; Bonner, T.N.; Castle, J.M.

1998-01-01

At the Portsmouth Gaseous Diffusion Plant in Piketon, Ohio, USA, excess inventory of highly-enriched uranium (HEU) from US defense programs is being diluted to low-enriched uranium (LEU) for commercial use. The conversion is subject to a Verification Experiment overseen by the International Atomic Energy Agency (IAEA). The Verification Experiment is making use of monitoring technologies developed and installed by several DOE laboratories. One of the measures is a system for sealing valves in the process piping, which secures the path followed by uranium hexafluoride gas (UF 6 ) from cylinders at the feed stations to the blend point, where the HEU is diluted with LEU. The Authenticated Item Monitoring System (AIMS) was the alternative proposed by Sandia National Laboratories that was selected by the IAEA. Approximately 30 valves were sealed by the IAEA using AIMS fiber-optic seals (AFOS). The seals employ single-core plastic fiber rated to 125 C to withstand the high-temperature conditions of the heated piping enclosures at Portsmouth. Each AFOS broadcasts authenticated seal status and state-of-health messages via a tamper-protected radio-frequency transmitter mounted outside of the heated enclosure. The messages are received by two collection stations, operated redundantly

Educational reactor-physics experiments with the critical assemble TCA

Energy Technology Data Exchange (ETDEWEB)

Tsutsui, Hiroaki; Okubo, Masaaki; Igashira, Masayuki [Tokyo Inst. of Tech. (Japan); Horiki, Oichiro; Suzaki, Takenori

1997-10-01

The Tank-Type Critical Assembly (TCA) of Japan Atomic Energy Research Institute is research equipment for light water reactor physics. In the present report, the lectures given to the graduate students of Tokyo Institute of Technology who participated in the educational experiment course held on 26-30 August at TCA are rearranged to provide useful information for those who will implement educational basic experiments with TCA in the future. This report describes the principles, procedures, and data analyses for (1) Critical approach and Exponential experiment, (2) Measurement of neutron flux distribution, (3) Measurement of power distribution, (4) Measurement of fuel rod worth distribution, and (5) Measurement of safety plate worth by the rod drop method. (author)

Educational reactor-physics experiments with the critical assembly TCA

International Nuclear Information System (INIS)

Tsutsui, Hiroaki; Okubo, Masaaki; Igashira, Masayuki; Horiki, Oichiro; Suzaki, Takenori.

1997-10-01

The Tank-Type Critical Assembly (TCA) of Japan Atomic Energy Research Institute is research equipment for light water reactor physics. In the present report, the lectures given to the graduate students of Tokyo Institute of Technology who participated in the educational experiment course held on 26-30 August at TCA are rearranged to provide useful information for those who will implement educational basic experiments with TCA in the future. This report describes the principles, procedures, and data analyses for 1) Critical approach and Exponential experiment, 2) Measurement of neutron flux distribution, 3) Measurement of power distribution, 4) Measurement of fuel rod worth distribution, and 5) Measurement of safety plate worth by the rod drop method. (author)

The status of HEU to LEU core conversion activities at the Jamaica SLOWPOKE

Energy Technology Data Exchange (ETDEWEB)

Preston, J.; Grant, C., E-mail: john.preston@uwimona.edu.jm [Univ. of the West Indies, Mona Campus, International Centre for Environmental and Nuclear Sciences, Mona (Jamaica)

2012-12-15

The SLOWPOKE reactor in Jamaica has been operated by the International Centre for Environmental and Nuclear Sciences, University of the West Indies since 1984, mainly for the purpose of Neutron Activation Analysis. The HEU core with current utilization has another 14 years of operation, before the addition of a large beryllium annulus would be required to further extend the life-time by 15 years. However, in keeping with the spirit of the Reduced Enrichment for Research and Test Reactors (RERTR) program, the decision was taken in 2003 to convert the core from HEU to LEU, in line with those at the Ecole Polytechnic and RMC SLOWPOKE facilities. This paper reports on the current status of the conversion activities, including key fuel manufacture and regulatory issues, which have seen substantial progress during the last year. A timetable for the complete process is given, and provided that the fuel fabrication can be completed in the estimated 18 months, the core conversion should be accomplished by the end of 2014. (author)

Basic experiments of reactor physics using the critical assembly TCA

International Nuclear Information System (INIS)

Obara, Toru; Igashira, Masayuki; Sekimoto, Hiroshi; Nakajima, Ken; Suzaki, Takenori.

1994-02-01

This report is based on lectures given to graduate students of Tokyo Institute of Technology. It covers educational experiments conducted with the Tank-Type Critical Assembly (TCA) at Japan Atomic Energy Research Institute in July, 1993. During this period, the following basic experiments on reactor physics were performed: (1) Critical approach experiment, (2) Measurement of neutron flux distribution, (3) Measurement of power distribution, (4) Measurement of fuel rod worth distribution, (5) Measurement of safety sheet worth by the rod drop method. The principle of experiments, experimental procedure, and analysis of results are described in this report. (author)

International Handbook of Evaluated Criticality Safety Benchmark Experiments - ICSBEP (DVD), Version 2013

International Nuclear Information System (INIS)

2013-01-01

The Criticality Safety Benchmark Evaluation Project (CSBEP) was initiated in October of 1992 by the United States Department of Energy. The project quickly became an international effort as scientists from other interested countries became involved. The International Criticality Safety Benchmark Evaluation Project (ICSBEP) became an official activity of the Organisation for Economic Co-operation and Development (OECD) Nuclear Energy Agency (NEA) in 1995. This handbook contains criticality safety benchmark specifications that have been derived from experiments performed at various nuclear critical experiment facilities around the world. The benchmark specifications are intended for use by criticality safety engineers to validate calculational techniques used to establish minimum subcritical margins for operations with fissile material and to determine criticality alarm requirement and placement. Many of the specifications are also useful for nuclear data testing. Example calculations are presented; however, these calculations do not constitute a validation of the codes or cross section data. The evaluated criticality safety benchmark data are given in nine volumes. These volumes span nearly 66,000 pages and contain 558 evaluations with benchmark specifications for 4,798 critical, near critical or subcritical configurations, 24 criticality alarm placement/shielding configurations with multiple dose points for each and 200 configurations that have been categorised as fundamental physics measurements that are relevant to criticality safety applications. New to the Handbook are benchmark specifications for Critical, Bare, HEU(93.2)- Metal Sphere experiments referred to as ORSphere that were performed by a team of experimenters at Oak Ridge National Laboratory in the early 1970's. A photograph of this assembly is shown on the front cover

Measurement of critical mass for an assembly of bare uranium shells

International Nuclear Information System (INIS)

Myers, W.L.; Goulding, C.A.; Hollas, C.L.

1997-01-01

As part of the research into nuclear measurement techniques, a series of measurements was performed that have applications to criticality safety and nuclear material handling. The critical mass of a set of bare, enriched-uranium metal hemispherical shells, known as the Rocky Flats shells, was measured for an assembly having an inside radius of 2.347 cm. The critical mass value was extrapolated from a series of subcritical measurements using three different kinds of sources (AmBe, AmF, and 252 Cf) placed at the center of the shells. Two kinds of neutron detection configurations (a 1% efficiency and a 25% efficiency configuration) were used to make the measurements

Critical assembly of uranium enriched to 10% in uranium-235

International Nuclear Information System (INIS)

Hansen, G.E.; Paxton, H.E.

1979-01-01

Big Ten is described in the detail appropriate for a benchmark critical assembly. Characteristics provided are spectral indexes and a detailed neutron flux spectrum, Rossi-α on a reactivity scale established by positive periods, and reactivity coefficients of a variety of isotopes, including the fissionable materials. The observed characteristics are compared with values calculated with ENDF/B-IV cross sections

The University of Missouri Research Reactor HEU to LEU conversion project status

Energy Technology Data Exchange (ETDEWEB)

McKibben, James C; Kutikkad, Kiratadas; Foyto, Leslie P; Peters, Nickie J; Solbrekken, Gary L; Kennedy, John [University of Missouri Research Reactor, Missouri (United States); Stillman, John A; Feldman, Earl E; Tzanos, Constantine P; Stevens, John G [Argonne National Laboratory, Argonne, Illinois (United States)

2012-03-15

The University of Missouri Research Reactor (MURR) is one of five U.S. high performance research and test reactors that are actively collaborating with the U.S. Department of Energy (DOE) to find a suitable low-enriched uranium (LEU) fuel replacement for the currently required highly-enriched uranium (HEU) fuel. A conversion feasibility study based on U-10Mo monolithic LEU fuel was completed in 2009. It was concluded that the proposed LEU fuel assembly design, in conjunction with an increase in power level from 10 to 12 MWth, will (1) maintain safety margins during operation, (2) allow operating fuel cycle lengths to be maintained for efficient and effective use of the facility, and (3) preserve an acceptable level and spectrum of key neutron fluxes to meet the scientific mission of the facility. The MURR and Argonne National Laboratory (ANL) team is continuing to work toward realization of the conversion. The 'Preliminary Safety Analysis Report Methodologies and Scenarios for LEU Conversion of MURR' was completed in June 2011. This report documents design parameter values critical to the Fuel Development (FD), Fuel Fabrication Capability (FFC) and Hydromechanical Fuel Test Facility (HMFTF) projects. The report also provides a preliminary evaluation of safety analysis techniques and data that will be needed to complete the fuel conversion Safety Analysis Report (SAR), especially those related to the U-10Mo monolithic LEU fuel. Specific studies are underway to validate the proposed path to an LEU fuel conversion. Coupled fluid-structure simulations and experiments are being conducted to understand the hydrodynamic plate deformation risk for 0.965 mm (38 mil) thick fuel plates. Methodologies that were recently developed to answer the U.S. Nuclear Regulatory Commission (NRC) Request for Additional Information (RAI) regarding the MURR 2006 relicensing submittal will be used in the LEU conversion effort. Transition LEU fuel elements that will have a minimal impact on

Reactor physics studies in the GCFR phase-II critical assembly

International Nuclear Information System (INIS)

Pond, R.B.

1976-09-01

The reactor physics studies performed in the gas cooled fast reactor (GCFR) mockup on ZPR-9 are covered. This critical assembly, designated Phase II in the GCFR program, had a single zone PuO 2 -UO 2 core composition and UO 2 radial and axial blankets. The assembly was built both with and without radial and axial stainless steel reflectors. The program included the following measurements: small-sample reactivity worths of reactor constituent materials (including helium); 238 U Doppler effect; uranium and plutonium reaction rate distributions; thorium, uranium, and plutonium α and reactor kinetics. Analysis of the measurements used ENDF/B-IV nuclear data; anisotropic diffusion coefficients were used to account for neutron streaming effects. Comparison of measurements and calculations to GCFR Phase I are also made

Boiling transition phenomenon in BWR fuel assemblies effect of fuel spacer shape on critical power

International Nuclear Information System (INIS)

Yamamoto, Yasushi; Morooka, Shin-ichi; Mitsutake, Toru; Yokobori, Seiichi; Kimura, Jiro.

1996-01-01

A thorough understanding of the thermal-hydraulic phenomena near fuel spacer is necessary for the accurate prediction of the critical power of BWR fuel assemblies, and is thus essential for effective developments of a new BWR fuel assembly. The main purpose of this study is to develop an accurate method for predicting the effect of spacer shapes on critical power. Tests have been conducted under actual BWR operating conditions, using an annulus flow channel consisting of a heated rod and circular-tube channel, and BWR simulated 4x4 rod bundles with heater rods unheated just upsteam of spacer. The effect of spacer shapes on critical power was predicted analytically based on the droplet deposition rate estimation. The droplet deposition rate for different spacer shapes was calculated using a single-phase flow model. The prediction results were compared with the test results for the annulus flow channel using ring-type spacers. Analytical results of critical power agreed with measured critical power from point of the effects of changes in the rod-spacer clearance and the spacer thickness on critical power. (author)

Trial evaluation on criticality safety of the fuel assemblies at falling accident as spent fuel transport and storage cask

International Nuclear Information System (INIS)

Tadano, Tomoaki

2016-01-01

The authors conducted critical safety assessment on the supposed event at the time of a fall accident of cask, and examined the influence on criticality safety. If the spacer of fuel assembly is sound, it is assumed that the pitch of fuel rod interval changes, and if the spacer is broken, it is assumed that the fuel rod is unevenly distributed in the basket. For the critical calculation of fuel assembly basket system, they performed it using a calculation code. For both of the single cell and assembly, calculation results showed an increase in the effective multiplication factor of reactivity of 2-3%. When this reactivity is applied to the criticality analysis result of PWR fuel assembly, the value approaches to the limit 0.95 of the neutron effective multiplication factor keff. However, the keff when new fuel is loaded is sufficiently lower than 0.93. Therefore, it is unlikely that the criticality analysis result approaches to 0.95 at all burnups, and the possibility to become criticality is very low in actual spent fuel transport. When considering the reactivity of this research, it is possible that the design condition for the assumption of novel fuel loading becomes severer. Furthermore, criticality analysis under non-uniform pitch will become necessary, and criticality safety analysis for BWR fuel with heterogeneous enrichment degree and burnup degree will become also necessary. (A.O.)

Criticality safety assessment of FBTR fuel sub-assemblies using WIMS cross section set

International Nuclear Information System (INIS)

Gupta, H.C.; Chakraborty, B.

2002-01-01

Full text: FBTR's irradiated fuel sub-assemblies (FSAs) are sent to RML at Indira Gandhi Centre for Atomic Research for post irradiation examination. The FSAs are cut open and the fuel pins are separated for examination in the hot cells. It was required to evaluate the criticality safety in handling the FSAs in the hot cells. Criticality safety studies for handling two as well as three irradiated FSAs in the hot cells under dry conditions were carried out by the Safety Group at IGCAR, Kalpakkam. Monte Carlo code KENO (Version Va) which uses 16-group Hansen-Roach cross-section set was used for the calculations. Subsequently, during the safety review of the proposition by the Safety Review Committee (SARCOP) of AERB, it was stipulated to carry out the criticality safety studies under flooded condition also. We carried out the criticality safety studies for these fuel sub assemblies in different configurations under dry (buried in concrete) as well as wet condition (flooded with light water) using Monte Carlo codes MONALI (developed at BARC) and KENO4 using WlMS-69 group cross section set. Results of our analyses under various conditions are presented in this paper

A simplified treatment of radial enrichment distributions of LWR fuel assemblies in criticality calculations

International Nuclear Information System (INIS)

Hennebach, M.; Schnorrenberg, N.

2008-01-01

Criticality safety assessments are usually performed for fuel assembly models that are as generic as possible to encompass small modifications in geometry that have no impact on criticality. Dealing with different radial enrichment distributions for a fuel assembly type, which is especially important for BWR fuel, poses more of a challenge, since this characteristic is rather obviously influencing the neutronic behaviour of the system. Nevertheless, the large variability of enrichment distributions makes it very desirable and even necessary to treat them in a generalized way, both to keep the criticality safety assessment from becoming too unwieldy and to avoid having to extend it every time a new variation comes up. To be viable, such a generic treatment has to be demonstrably covering, i.e. lead to a higher effective neutron multiplication factor k eff than any of the radial enrichment distributions it represents. Averaging the enrichment evenly over the fuel rods of the assembly is a general and simple approach, and under reactor conditions, it is also a covering assumption: the graded distribution is introduced to achieve a linear power distribution, therefore reducing the enrichment of the better moderated rods at the edge of the assembly. With an even distribution of the average enrichment over all rods, these wellmoderated rods will cause increased fission rates at the assembly edges and a rise in k eff . Since the moderator conditions in a spent nuclear fuel cask differ strongly from a reactor even when considering optimal moderation, the proof that a uniform enrichment distribution is a covering assumption compared with detailed enrichment distributions has to be cask-specific. In this report, a method for making that proof is presented along with results for fuel assemblies from BWR reactors. All results are from three-dimensional Monte Carlo calculations with the SCALE 5.1 code package [1], using a 44-group neutron crosssection library based on ENDF

Thermal adaptation of mesophilic and thermophilic FtsZ assembly by modulation of the critical concentration.

Directory of Open Access Journals (Sweden)

Luis Concha-Marambio

Full Text Available Cytokinesis is the last stage in the cell cycle. In prokaryotes, the protein FtsZ guides cell constriction by assembling into a contractile ring-shaped structure termed the Z-ring. Constriction of the Z-ring is driven by the GTPase activity of FtsZ that overcomes the energetic barrier between two protein conformations having different propensities to assemble into polymers. FtsZ is found in psychrophilic, mesophilic and thermophilic organisms thereby functioning at temperatures ranging from subzero to >100°C. To gain insight into the functional adaptations enabling assembly of FtsZ in distinct environmental conditions, we analyzed the energetics of FtsZ function from mesophilic Escherichia coli in comparison with FtsZ from thermophilic Methanocaldococcus jannaschii. Presumably, the assembly may be similarly modulated by temperature for both FtsZ orthologs. The temperature dependence of the first-order rates of nucleotide hydrolysis and of polymer disassembly, indicated an entropy-driven destabilization of the FtsZ-GTP intermediate. This destabilization was true for both mesophilic and thermophilic FtsZ, reflecting a conserved mechanism of disassembly. From the temperature dependence of the critical concentrations for polymerization, we detected a change of opposite sign in the heat capacity, that was partially explained by the specific changes in the solvent-accessible surface area between the free and polymerized states of FtsZ. At the physiological temperature, the assembly of both FtsZ orthologs was found to be driven by a small positive entropy. In contrast, the assembly occurred with a negative enthalpy for mesophilic FtsZ and with a positive enthalpy for thermophilic FtsZ. Notably, the assembly of both FtsZ orthologs is characterized by a critical concentration of similar value (1-2 μM at the environmental temperatures of their host organisms. These findings suggest a simple but robust mechanism of adaptation of FtsZ, previously shown

Reactor physics studies in the steam flooded GCFR-Phase II critical assembly

International Nuclear Information System (INIS)

Bhattacharyya, S.K.

1978-08-01

A possible accident scenario in a Gas-Cooled Fast Reactor (GCFR) is the leakage of secondary steam into the core. Considerable analytical effort has gone into the study of the effects of such an accidental steam entry. The work described represents the first full scale experimental study of the steam-entry phenomenon in GCFRs. The reference GCFR model used for the study was the benchmark GCFR Phase II assembly, and polyethylene foam was used to provide a very homogeneous steam simulation. The reactivity worth of steam entry was measured for three different steam densities. In addition, a set of integral physics parameters were measured in the largest steam density (0.008 g/cm 3 ) configuration. The corresponding parameters were also measured in dry reference GCFR critical assembly for comparison. The experiments were analyzed using ENDF/B-IV data and two-dimensional diffusion theory methods. As in earlier GCFR critical experiments analysis, the Benoist method was used to treat the problem of neutron streaming

Data base of reactor physics experimental results in Kyoto University critical assembly experimental facilities

International Nuclear Information System (INIS)

Ichihara, Chihiro; Fujine, Shigenori; Hayashi, Masatoshi

1986-01-01

The Kyoto University critical assembly experimental facilities belong to the Kyoto University Research Reactor Institute, and are the versatile critical assembly constructed for experimentally studying reactor physics and reactor engineering. The facilities are those for common utilization by universities in whole Japan. During more than ten years since the initial criticality in 1974, various experiments on reactor physics and reactor engineering have been carried out using many experimental facilities such as two solidmoderated cores, a light water-moderated core and a neutron generator. The kinds of the experiment carried out were diverse, and to find out the required data from them is very troublesome, accordingly it has become necessary to make a data base which can be processed by a computer with the data accumulated during the past more than ten years. The outline of the data base, the data base CAEX using personal computers, the data base supported by a large computer and so on are reported. (Kako, I.)

IER-297 CED-2: Final Design for Thermal/Epithermal eXperiments with Jemima Plates with Polyethylene and Hafnium

Energy Technology Data Exchange (ETDEWEB)

Nelson, A. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Percher, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zywiec, W. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heinrichs, D. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2018-01-11

This report presents the final design (CED-2) for IER-297, and focuses on 15 critical configurations using highly enriched uranium (HEU) Jemima plates moderated by polyethylene with and without hafnium diluent. The goal of the U.S. Nuclear Criticality Safety Program’s Thermal/Epithermal eXperiments (TEX) is to design and conduct new critical experiments to address high priority nuclear data needs from the nuclear criticality safety and nuclear data communities, with special emphasis on intermediate energy (0.625 eV – 100 keV) assemblies that can be easily modified to include various high priority diluent materials. The TEX (IER 184) CED-1 Report [1], completed in 2012, demonstrated the feasibility of meeting the TEX goals with two existing NCSP fissile assets, plutonium Zero Power Physics Reactor (ZPPR) plates and highly enriched uranium (HEU) Jemima plates. The first set of TEX experiments will focus on using the plutonium ZPPR plates with polyethylene moderator and tantalum diluents.

A neutronic feasibility study for LEU conversion of the IR-8 research reactor

International Nuclear Information System (INIS)

Deen, J.R.; Hanan, N.A.; Matos, J.E.; Egorenkov, P.M.; Nasonov, V.A.

1998-01-01

Equilibrium fuel cycle comparisons for the IR-8 research reactor were made for HEU (90%), HEU (36%), and LEU (19.75%) fuel assembly (FA) designs using three dimensional multi-group diffusion theory models benchmarked to detailed Monte Carlo models of the reactor. Comparisons were made of changes in reactivity, cycle length, average 235 U discharge burnup, thermal neutron flux, and control rod worths for the 90% and 36% enriched IRT-3M fuel assembly and the 19.75% enriched IRT-4M fuel assembly with the same fuel management strategy. The results of these comparisons showed that a uranium density of 3.5 g/cm 3 in the fuel meat would be required in the LEU IRT-4M fuel assembly to match the cycle length of the HEU (90%) IRT-3M FA and an LEU density of 3.7 g/cm 3 is needed to match the cycle length of the HEU (36%) IRT-3M FA. (author)

A comparison of reaction rate calculations using Endf/B-VII with critical assembly measurements

International Nuclear Information System (INIS)

Wilkerson, C.; Mac Innes, M.; Barr, D.; Trellue, H.; MacFarlane, R.; Chadwick, M.

2008-01-01

We present critical assembly reaction rate data, and modeling of the same using the recently released Endf/B-VII library. While some of the experimental measurements were performed as long as 50 years ago, the results have not been widely used/available outside of Los Alamos. Over the years, a variety of target foils were fabricated and placed in differing neutron spectrum/fluence environments within critical assemblies. Neutron-induced reactions such as (n,γ), (n,2n), and (n,f) on these targets were measured, typically referenced to 235 U(n,f) or 239 Pu(n,f). Because the cross section for the latter reactions are now well known, these experiments provide a rich data set for testing evaluated cross sections. Due to the large variety of critical assemblies that were historically available at Los Alamos, it was possible to make measurements in spectral environments ranging from hard (Pu Jezebel, center of Pu Flattop) through intermediate (Big Ten) to degraded (reflector region of Flattop). This broad range of configurations allows us to test both the cross section magnitudes and their energy dependencies. We will present data, along with reaction rate predictions using primarily MCNP5 in conjunction with Endf/B-VII, for a number of target nuclei, including iridium, isotopes of uranium (e.g., 233, 235, 237, 238), neptunium (237), plutonium (239), and americium (241). (authors)

Benchmarks of subcriticality in accelerator-driven system at Kyoto University Critical Assembly

Directory of Open Access Journals (Sweden)

Cheol Ho Pyeon

2017-09-01

Full Text Available Basic research on the accelerator-driven system is conducted by combining 235U-fueled and 232Th-loaded cores in the Kyoto University Critical Assembly with the pulsed neutron generator (14 MeV neutrons and the proton beam accelerator (100 MeV protons with a heavy metal target. The results of experimental subcriticality are presented with a wide range of subcriticality level between near critical and 10,000 pcm, as obtained by the pulsed neutron source method, the Feynman-α method, and the neutron source multiplication method.

Studies of mixed HEU-LEU-MTR cores using 3D models

Energy Technology Data Exchange (ETDEWEB)

Haenggi, P.; Lehmann, E.; Hammer, J.; Christen, R. [Paul Scherrer Institute, Villigen (Switzerland)

1997-08-01

Several different core loadings were assembled at the SAPHIR research reactor in Switzerland combining the available types of MTR-type fuel elements, consisting mainly of both HEU and LEU fuel. Bearing in mind the well known problems which can occur in such configurations (especially power peaking), investigations have been carried out for each new loading with a 2D neutron transport code (BOXER). The axial effects were approximated by a global buckling value and therefore the radial effects could be studied in considerably detail. Some of the results were reported at earlier RERTR meetings and were compared to those obtained by other methods and with experimental values. For the explicit study of the third dimension of the core, another code (SILWER), which has been developed in PSI for LWR power plant cores, has been selected. With the help of an adapted model for the MTR-core of SAPHIR, several important questions have been addressed. Among other aspects, the estimation of the axial contribution to the hot channel factors, the influence of the control rod position and of the Xe-poisoning on the power distribution were studied. Special attention was given to a core position where a new element was assumed placed near a empty, water filled position. The comparison of elements of low and high enrichments at this position was made in terms of the induced power peaks, with explicit consideration of axial effects. The program SILWER has proven to be applicable to MTR-cores for the investigation of axial effects. For routine use as for the support of reactor operation, this 3D code is a good supplement to the standard 2D model.

Basket criticality design of a dual purpose cask for VVER 1000 spent fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Rezaeian, Mahdi [Nuclear Science and Technology Research Institute, Tehran (Iran, Islamic Republic of); Kamali, Jamshid [Atomic Energy Organization of Iran (AEOI), Tehran (Iran, Islamic Republic of)

2016-12-15

Dual purpose cask technology is one of the most prominent options for interim storage of spent fuels following their removal from reactors. Criticality safety of the spent fuel assemblies are ensured by design of the basket within these casks. In this study, a set of criticality design calculations of a dual purpose cask for 12 VVER 1000 spent fuel assemblies of Bushehr nuclear power plant were carried out. The basket material of borated stainless steel with 0.5 to 2.5 wt% of boron and Boral (Al-B{sub 4}C) with 1.5 to 40 wt% of boron carbide, were investigated and the minimum required receptacle pitch of the basket was determined. Using the calculated receptacle pitch of the basket, the minimum required diameter of the cavity could be established.

A new facility for the determination of critical heat flux in nuclear fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Fortman, R A; Hadaller, G I; Hamilton, R C; Hayes, R C; Shin, K S; Stern, F [Stern Laboratories Inc., Hamilton, ON (Canada)

1993-11-01

A facility for the determination of critical heat flux in simulated reactor fuel assemblies has been constructed at Stern Laboratories for CANDU Owners` Group. This paper describes the facility and method of testing. 9 figs.

Low enrichment fuel conversion for Iowa State University

International Nuclear Information System (INIS)

Rohach, A.F.; Hendrickson, R.A.

1991-08-01

Work during the reported period was centered primarily in preparation for receiving the LEU fuel and the shipping of the HEU fuel. This included development of procedures and tools for the disassembly process. During the period we held many practice sessions applying these tools and practices to a dummy fuel assembly. The LEU fuel was received on April 10, 1991 and the reactor was shut down on May 3, 1991 for refueling. The twelve HEU fuel assemblies in the UTR-10 reactor core were removed and disassembled during the week of May 6--9, 1991. The disassembly process went smoothly with only a few minor problems. Also during this reporting period several experimental measurements and preventative maintenance tasks were accomplished. Finally procedures and practices have been developed for the new LEU fuel loading and critical experiments which are to be completed during the late summer of 1991

Neutronic calculations in core conversion of the IAN-R1 research reactor from MTR HEU to TRIGA LEU fuel

International Nuclear Information System (INIS)

Sarta Fuentes, Jose A.; Castiblanco, L.A.

2003-01-01

With cooperation of the International Atomic Energy Agency (IAEA), neutronic calculations were carried out for conversion of the Ian-R1 Reactor from MTR-HEU fuel to TRIGA-LEU fuel. In order to establish a staff for neutronic calculation at the Instituto de Cancan's Nucleares y Energia s Alternatives (INEA) a program was established. This program included training, acquisition of hardware, software and calculation for the core with MTR-HEU fuel , enriched nominally to 93% and calculation for several arrangements with the TRIGA-LEU fuel, enriched to 19.7%. The results were verified and compared with several groups of calculation at the Instituto Nacional de Investigaciones Nucleares (ININ) in Mexico, and General Atomics (GA) in United States. As a result of this program, several technical reports have been wrote. (author)

Safe operation of critical assemblies and research reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1960-09-15

Some countries have accumulated considerable experience in the operation of these reactors and have in the process developed safe practices. On the other hand, other countries which have recently acquired, or will soon acquire, such reactors do not have sufficient background of experience with them to have developed full knowledge regarding their safe operation. In this situation, the International Atomic Energy Agency has considered that it would be useful to make available to all its Member States a set of recommendations on the safe operation of these reactors, based on the accumulated experience and best practices. The Director General accordingly nominated a Pane Ion Safe Operation of Critical Assemblies and Research Reactors to assist the Agency's Secretariat in drafting such recommendations

Criticality safety study of shutdown diffusion cascade coolers

International Nuclear Information System (INIS)

Paschal, L.S.; Basoglu, B.; Bentley, C.L.; Dunn, M.E.

1996-01-01

Gaseous diffusion plants use cascade coolers in the production of highly enriched uranium (HEU) to remove heat from the enriched stream of UF 6 . The cascade coolers operate like shell and tube heat exchangers with the UF 6 on the shell side and Freon on the tube side. Recirculating cooling water (RCW) in condensers is used to cool the Freon. A criticality safety analysis was previously performed for cascade coolers during normal operation. The purpose of this paper is to evaluate several different hypothetical accidents regarding RCW ingress into the cooler to determine whether criticality safety concerns exist

Documentation Experiences for Jamaican SLOWPOKE-2 Conversion from HEU to LEU

International Nuclear Information System (INIS)

Warner, T.-A.; Dennis, H.; Antoine, J.

2015-01-01

The Jamaican SLOWPOKE–2 (JM–1) is a 20 kW research reactor manufactured by Atomic Energy of Canada Limited and has been operating since March 1984, in the department of the International Centre for Environmental and Nuclear Sciences (ICENS), at the University of the West Indies, Mona Campus in Kingston, Jamaica. The pool type reactor has been primarily used for Neutron Activation Analysis in environmental, agricultural, geochemical, health-related studies and mineral exploration. The University, assisted by the IAEA under the GTRI/RERTR program, is currently in the process of converting from HEU to LEU. Extensive documentation on policies, general requirements, elements of the conversion quality assurance (QA) system and conversion QA administrative procedures is required for the conversion. The core conversion activities are being carried out in accordance with current international standards and regulatory guidelines of the newly established Jamaican Radiation Safety Authority (RSA) with agreement between the RSA and IAEA or DOE related to Nuclear Safety and Control. The documentation structure has taken into consideration nuclear safety and licensing, LEU fuel design and conversion analysis, LEU fuel procurement and fabrication, removal of HEU fuel and reactor maintenance and conversion and commissioning, with the conversion QA manual at the apex of the structure. To a large extent, the documentation format will adhere to that of the IAEA applicable regulatory standards and guidance documents. The major challenge of the conversion activities, it is envisioned, will come from the absence of any previous regulatory framework in Jamaica; however, a timeline for the process, which includes training and equipping of regulators, will guide operation. (author)

Research on the reactor physics using the Kyoto University Critical Assembly (KUCA)

International Nuclear Information System (INIS)

1986-10-01

The Kyoto University Critical Assembly [KUCA] is a multi-core type critical assembly established in 1974, as a facility for the joint use study by researchers of all universities in Japan. Thereafter, many reactor physics experiments have been carried out using three cores (A-, B-, and C-cores) in the KUCA. In the A- and B-cores, solid moderator such as polyethylene or graphite is used, whereas light-water is utilized as moderator in the C-core. The A-core has been employed mainly in connection with the Cockcroft-Walton type accelerator installed in the KUCA, to measure (1) the subcriticality by the pulsed neutron technique for the critical safety research and (2) the neutron spectrum by the time-of-flight technique. Recently, a basic study on the tight lattice core has also launched using the A-core. The B-core has been employed for the research on the thorium fuel cycle ever since. The C-core has been employed (1) for the basic studies on the nuclear characteristics of light-water moderated high-flux research reactors, including coupled-cores, and (2) for a research related to reducing enrichment of uranium fuel used in research reactors. The C-core is being utilized in the reactor laboratory course experiment for students of ten universities in Japan. The data base of the KUCA critical experiments is generated so far on the basis of approximately 350 experimental reports accumulated in the KUCA. Besides, the assessed KUCA code system has been established through analyses on the various KUCA experiments. In addition to the KUCA itself, both of them are provided for the joint use study by researchers of all universities in Japan. (author)

UBERA-6 project: Achievements of 4 working years

International Nuclear Information System (INIS)

Blaumann, H; Fernandez, C; Dell Occhio, L; D Ovidio, C; Fabro, J; Miceli, M; Novara O; Perez, A; Taboada, H

2009-01-01

On May 2005 the President of CNEA created the UBERA-6 project, belonging to the former Technology and Environmental Management, with the aim to convert to Low Enriched Uranium (LEU) the RA-6 reactor core, to swap with the US Department of Energy (US-DoE) equivalent inventories of High Enriched Uranium (HEU) for LEU, to export to USA the spent HEU core and to recover and downblend to LEU remnant HEU inventories contained in fuel and irradiation target scraps. By means of two contracts signed by CNEA and US-DoE, acquisition of consumables and graphite reflectors, the fabrication of LEU core replacement, conditioning, transport and exportation of spent HEU core and subsequent supply of fresh LEU for fuel and irradiation targets used in our research reactors were costed. During July, 2006 468 HEU based fresh plates were exported to USA. On June 30th, 2007 the RA-6 reactor temporarily stopped working and its personnel remover the HEU core to the auxiliary pool. On November 7th the former spent HEU based core was exported to USA. During May and July, 2008 the new RA-6 reactor LEU based core and control assemblies were provided. During March, 2009 the RA-6 reactor became critical. For recovering and blending down of remnant HEU inventories, the Triple Height Laboratory (LTA) was refurbished. A Supplemental Agreement to one of the original contract between CNEA and US-DoE will financially support the refurbishment of the Radiochemical Facility Laboratory (LFR) and so reprocess irradiated HEU retained in radioisotope production filters to downblend into LEU, as well as the separation of the pair Sr90-Y90 and of Cs137 inventories for further application in Nuclear Medicine. [es

Sensitivity coefficients of reactor parameters in fast critical assemblies and uncertainty analysis

International Nuclear Information System (INIS)

Aoyama, Takafumi; Suzuki, Takayuki; Takeda, Toshikazu; Hasegawa, Akira; Kikuchi, Yasuyuki.

1986-02-01

Sensitivity coefficients of reactor parameters in several fast critical assemblies to various cross sections were calculated in 16 group by means of SAGEP code based on the generalized perturbation theory. The sensitivity coefficients were tabulated and the difference of sensitivity coefficients was discussed. Furthermore, the uncertainty of calculated reactor parameters due to cross section uncertainty were estimated using the sensitivity coefficients and cross section covariance data. (author)

Loss-of-Flow and Loss-of-Pressure Simulations of the BR2 Research Reactor with HEU and LEU Fuel

Energy Technology Data Exchange (ETDEWEB)

Licht, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Bergeron, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Sikik, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Van den Branden, G. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium); Koonen, E. [Belgian Nuclear Research Center (SCK-CEN), Mol (Belgium)

2016-01-01

Belgian Reactor 2 (BR2) is a research and test reactor located in Mol, Belgium and is primarily used for radioisotope production and materials testing. The Materials Management and Minimization (M3) Reactor Conversion Program of the National Nuclear Security Administration (NNSA) is supporting the conversion of the BR2 reactor from Highly Enriched Uranium (HEU) fuel to Low Enriched Uranium (LEU) fuel. The reactor core of BR2 is located inside a pressure vessel that contains 79 channels in a hyperboloid configuration. The core configuration is highly variable as each channel can contain a fuel assembly, a control or regulating rod, an experimental device, or a beryllium or aluminum plug. Because of this variability, a representative core configuration, based on current reactor use, has been defined for the fuel conversion analyses. The code RELAP5/Mod 3.3 was used to perform the transient thermal-hydraulic safety analyses of the BR2 reactor to support reactor conversion. The input model has been modernized relative to that historically used at BR2 taking into account the best modeling practices developed by Argonne National Laboratory (ANL) and BR2 engineers.

Criticality alarm device

International Nuclear Information System (INIS)

Kasai, Kenji.

1994-01-01

The device of the present invention is utilized, for example, to a reprocessing facility for storing and processing nuclear fuels and measures and controls the nuclear fuel assembly system so as not to exceed criticality. That is, a conventional criticality alarm device applies a predetermined processing to neutron fluxes generated from a nuclear fuel assembly system containing nuclear fuels and outputs an alarm. The device of the present invention comprises (1) a neutron flux supply source for increasing and decreasing neutron fluxes periodically and supplying them to nuclear fuel assemblies, (2) a detector for detecting neutron fluxes in the nuclear fuel assemblies, (3) a critical state judging section for judging the critical state of the nuclear fuel assemblies based on the periodically changing signals obtained from the detector (2) and (4) an alarm section for outputting criticality alarms depending on the result of the judgement. The device of the present invention can accurately recognize the critical state of the nuclear fuel assembly system and can forecast reaching of the nuclear fuel assembly to criticality or prompt neutron critical state. (I.S.)

Fuel depletion analyses for the HEU core of GHARR-1: Part II: Fission product inventory

International Nuclear Information System (INIS)

Anim-Sampong, S.; Akaho, E.H.K.; Boadu, H.O.; Intsiful, J.D.K.; Osae, S.

1999-01-01

The fission product isotopic inventories have been estimated for a 90.2% highly enriched uranium (HEU) fuel lattice cell of the Ghana Research Reactor-1 (GHARR-1) using the WIMSD/4 transport lattice code. The results indicate a gradual decrease in the Xe 135 inventory, and saturation trend for Sm 149 , Cs 134 and Cs 135 inventories as the fuel is depleted to 10,000 MWd/tU. (author)

HEU core conversion of Russian production reactors: a major threat to the international RERTR regime

International Nuclear Information System (INIS)

Kuperman, Alan J.; Leventhal, Paul L.

1998-01-01

This paper calls the attention for the major threat to the International Reduced Enrichment for Research and Test Reactors (RERTR) program, represented by the HEU core conversion of russian production reactors. This program aims to reduce and eventually eliminate international civilian commerce in nuclear weapons-usable, highly enriched uranium , and thereby significantly lower risks of the material being stolen or diverted by terrorist or states for producing nuclear weapons

A Critical Appraisal of RAFT-Mediated Polymerization-Induced Self-Assembly

Science.gov (United States)

2016-01-01

Recently, polymerization-induced self-assembly (PISA) has become widely recognized as a robust and efficient route to produce block copolymer nanoparticles of controlled size, morphology, and surface chemistry. Several reviews of this field have been published since 2012, but a substantial number of new papers have been published in the last three years. In this Perspective, we provide a critical appraisal of the various advantages offered by this approach, while also pointing out some of its current drawbacks. Promising future research directions as well as remaining technical challenges and unresolved problems are briefly highlighted. PMID:27019522

Determination of Dancoff correction thermal utilization and thermal disadvantage factors of HEU and LEU cores of an MNSR

International Nuclear Information System (INIS)

Ofori, Y. T.

2013-07-01

Ghana Research Reactor-1 (GHARR-1), an MNSR (Miniature Neutron Source Reactor) is to be converted from HEU (Highly Enriched Uranium) to LEU (Low Enriched Uranium) fuel, along with all current MNSRs in various other countries. The purpose of the conversion is to minimize the use of HEU for non-proliferation of high-grade nuclear fuel. In this research work, a comparative study has been performed for the determination of the Dancoff, thermal utilization and thermal disadvantage factors of highly enriched uranium (HEU) and potential low enriched uranium (LEU) cores of GHARR-1. A one group transport theory and collision probability based methodologies was used to develop mathematical formulations for thermal utilization factor and thermal disadvantage factor assuming isotropic scattering. This methodology was implemented in a FORTRAN 95 based computer program THERMCALC, which uses Bessell and BesselK as subroutines developed to calculate the modified Bessel functions I n and K n respectively using the polynomial approximation method. Furthermore, a Dancoff correction factor of 0.1519 thermal utilization factor of 0.9767 and a thermal disadvantage factor of 1.894 were obtained for the 90.2% highly enriched Uranium core of GHARR-1. The results compare favorably with literature. Thus THERMCALC can be used as a reliable tool for the calculation of Dancoff, thermal utilization and disadvantage factors of MNSR cores. Other potential LEU cores; UO 2 (with different fuel meat densities and enrichments) and U 3 Si 2 have also been analysed. UO 2 with 12.6% of Uranium-235 was chosen as the most potential LEU core for the GHARR-1. (au)

MOCA, Criticality of VVER Reactor Hexagonal Fuel Assemblies

International Nuclear Information System (INIS)

KYNCL, Jan

1994-01-01

1 - Description of program or function: Criticality problem in neutron transport for hexagonal fuel assembly in VVER nuclear reactor. The assembly is assumed to be either arranged in an infinite hexagonal array or placed in vacuum. The problem is solved in three- dimensional geometry, using standard energy group formalism and assuming that effective scattering cross sections are presented as Legendre polynomial expansions. The code evaluates ten different physical quantities, e.g. multiplication factor, neutron flux per energy group and spatial zone, integrated over angle and power in any zone of the assembly. 2 - Method of solution: Monte Carlo method of successive generations is applied. Computation proceeds according to an analog random process. The code is organized into three blocks: In the first block, the input data are converted to quantities for use in the Monte Carlo calculation. An initial neutron distribution is calculated, which corresponds to a fission spectrum uniform in spatial and angular variables. The main calculations are carried out in the second block (subroutine PROC2). This block is subdivided into geometrical and physical parts. Neutron tracks in individual zones and groups as well as probabilities for the formation of secondary neutrons are calculated. In the third block (subroutine PROC3), the results are evaluated statistically. Effective multiplication coefficients, the neutron flux per group and zone, and respective errors are computed. These quantities serve as a basis for the evaluation of other quantities. The results are either printed or stored for future evaluations. 3 - Restrictions on the complexity of the problem: In the PC version of the program, the maximum number of neutrons is 1000, the maximum number of energy groups is 4, and the maximum number of material compositions is 15. Angular expansion of scattering cross sections is allowed up to P10. These restrictions can easily be removed by increasing input parameters and

Neutronic calculations for the conversion of the University of Florida Training Reactor from HEU to LEU fuel

International Nuclear Information System (INIS)

Dugan, E.T.; Diaz, N.J.; Kniedler, G.S.

1983-01-01

plate-type fuel. A final reason for converting to the SPERT fuel is related to a desire to upgrade the UFTR from a 100 to a 500 kw facility. Such a change would be difficult with the current aluminum-uranium alloy plate fuel since warping of the plates has been experienced at the 100 kw power level. A motivating force in the proposed UFTR conversion is the existence of the SPERT fuel in-house at the University of Florida (under a DOE agreement) and the DOE's encouragement to pursue the described conversion. The purpose of this paper is to present the results of detailed neutronic investigations performed as part of the feasibility study for the UFTR conversion from HEU to LEU fuel. These neutronics studies included two phases. In the first phase, the efforts were directed primarily towards finding a satisfactory metal-to-water ratio for the SPERT fuel. An acceptable metal-to-water ratio has to satisfy the following neutronics criteria: 1. The neutron multiplication factor, or k eff for the unrodded UFTR must lie in the range of 1.03 to 1.09 both for te current power limit of 100 kw and also for the proposed upgraded rating of 500 kw. 2. The system must be in an under moderated state. 3. Reactivity coefficients and other safety-related neutronics parameters (e.g. effective delayed neutron fraction and prompt neutron lifetime) must be such that current UFTR safety levels are either maintained or enhanced. For the Phase studies, the only permanent UFTR structural modification allowed is the insertion of new grid assemblies into the existing fuel boxes to hold the the cylindrical SPERT fuel in place. The Phase 2 neutronic studies examined the effects of certain additional UFTR structural changes using the metal-to-water ratio lattice determined in the Phase studies. These changes included systematic alterations in certain region thicknesses and compositions. Te primary intention of the Phase 2 studies was to optimize the peak thermal neutron flux level in the UFTR while

Neutronic calculations for the conversion of the University of Florida Training Reactor from HEU to LEU fuel

Energy Technology Data Exchange (ETDEWEB)

Dugan, E T; Diaz, N J [Department of Nuclear Engineering Sciences, University of Florida, Gainesville, FL (United States); Kniedler, G S [Reactor Analysis Group, TVA, Chattanooga, TN (United States)

1983-09-01

the plate-type fuel. A final reason for converting to the SPERT fuel is related to a desire to upgrade the UFTR from a 100 to a 500 kw facility. Such a change would be difficult with the current aluminum-uranium alloy plate fuel since warping of the plates has been experienced at the 100 kw power level. A motivating force in the proposed UFTR conversion is the existence of the SPERT fuel in-house at the University of Florida (under a DOE agreement) and the DOE's encouragement to pursue the described conversion. The purpose of this paper is to present the results of detailed neutronic investigations performed as part of the feasibility study for the UFTR conversion from HEU to LEU fuel. These neutronics studies included two phases. In the first phase, the efforts were directed primarily towards finding a satisfactory metal-to-water ratio for the SPERT fuel. An acceptable metal-to-water ratio has to satisfy the following neutronics criteria: 1. The neutron multiplication factor, or k{sub eff} for the unrodded UFTR must lie in the range of 1.03 to 1.09 both for te current power limit of 100 kw and also for the proposed upgraded rating of 500 kw. 2. The system must be in an under moderated state. 3. Reactivity coefficients and other safety-related neutronics parameters (e.g. effective delayed neutron fraction and prompt neutron lifetime) must be such that current UFTR safety levels are either maintained or enhanced. For the Phase studies, the only permanent UFTR structural modification allowed is the insertion of new grid assemblies into the existing fuel boxes to hold the the cylindrical SPERT fuel in place. The Phase 2 neutronic studies examined the effects of certain additional UFTR structural changes using the metal-to-water ratio lattice determined in the Phase studies. These changes included systematic alterations in certain region thicknesses and compositions. Te primary intention of the Phase 2 studies was to optimize the peak thermal neutron flux level in the

Low enrichment fuel conversion for Iowa State University

International Nuclear Information System (INIS)

Rohach, A.F.; Hendrickson, R.A.

1990-08-01

Work during the reported period was centered primarily in preparation for receiving the LEU fuel and the shipping of the HEU fuel. The LEU fuel has not been received. The HEU fuel assemblies for the UTR-10 reactor will not fit into any current research reactor shipping containers; therefore, the fuel assemblies must be disassembled and the fuel shipped as fuel plates. Procedures and practices have been developed so that the fuel assemblies will be disassembled in a shielded environment

Experience with the transport and storage casks CASTOR (registered) MTR 2 for spent nuclear fuel assemblies from research reactors

Energy Technology Data Exchange (ETDEWEB)

Jack, Allen; Rettenbacher, Katharina; Skrzyppek, Juergen [GNS Gesellschaft fuer Nuklear-Service mbH, Essen (Germany)

2011-07-01

The CASTOR (registered) MTR 2 cask was designed and manufactured by the company GNS during the 1990's for the transport and interim storage of spent nuclear fuel assemblies from various types of research reactors. Casks of this type have been used at the VKTA Research Centre in Rossendorf near Dresden, Germany as well as at the European Commission's Joint Research Centre at Petten and at the HOR reactor at Delft in the Netherlands. A total of 24 units have been used for the functions of transport and storage with various spent fuel types (VVER, HFR-HEU, and HOR-HEU) for more than ten years now. This type of packaging for radioactive material is a member of the CASTOR (registered) family of spent nuclear fuel casks used worldwide. Over 1000 units are loaded and in storage in Europe, Asia, Africa and North America. This paper presents the experience from the use of the casks for transport and storage in the past, as well as the prospects for the future. (author)

The experimental determination of the buckling in the bare heavy water natural uranium critical assembly 'RB'

Energy Technology Data Exchange (ETDEWEB)

Raisic, N M; Popovic, D D; Takac, S M; Djordjevic, M M [Boris Kidric Institute of Nuclear Sciences, Vinca, Beograd (Yugoslavia)

1960-03-15

The buckling in the bare heavy water natural uranium critical assembly was determined by measuring the thermal neutron flux distribution. The obtained value for the critical buckling at the temperature of 20 deg C is: B{sup 2} = (8.516 {+-} 0.02) m{sup -2}. The above error is a statistical one, obtained from several series of measurements. The possible systematic error was estimated as 0.1 m{sup -2}. (author)

The experimental determination of the buckling in the bare heavy water natural uranium critical assembly 'RB'

International Nuclear Information System (INIS)

Raisic, N.M.; Popovic, D.D.; Takac, S.M.; Djordjevic, M.M.

1960-01-01

The buckling in the bare heavy water natural uranium critical assembly was determined by measuring the thermal neutron flux distribution. The obtained value for the critical buckling at the temperature of 20 deg C is: B 2 = (8.516 ± 0.02) m -2 . The above error is a statistical one, obtained from several series of measurements. The possible systematic error was estimated as 0.1 m -2 . (author)

Solution High-Energy Burst Assembly (SHEBA) results from subprompt critical experiments with uranyl fluoride fuel

International Nuclear Information System (INIS)

Cappiello, C.C.; Butterfield, K.B.; Sanchez, R.G.; Bounds, J.A.; Kimpland, R.H.; Damjanovich, R.P.; Jaegers, P.J.

1997-01-01

Experiments were performed to measure a variety of parameters for SHEBA: behavior of the facility during transient and steady-state operation; characteristics of the SHEBA fuel; delayed-critical solution height vs solution temperature; initial reactor period and reactivity vs solution height; calibration of power level vs reactor power instrumentation readings; flux profile in SHEBA; radiation levels and neutron spectra outside the assembly for code verification and criticality alarm and dosimetry purposes; and effect on reactivity of voids in the fuel

Evaluation of neutron flux in the Pool Critical Assembly

International Nuclear Information System (INIS)

Lippincott, E.P.; Ruddy, F.H.; Gold, R.; Kellogg, L.S.; Roberts, J.H.

1984-09-01

A recently completed series of experiments in the Pool Critical Assembly (PCA) at Oak Ridge National Laboratory (ORNL) provided extensive neutron flux characterization of a mockup pressure vessel configuration. Considerable effort has been made to understand the uncertainties of the various measurements made in the PCA and to resolve discrepancies in the data. Additional measurements are available for similar configurations in the Oak Ridge Reactor-Poolside Facility (ORR-PSF) at ORNL and in the NESDIP facility in the UK. Comparisons of these results, together with associated neutron field calculations, enable a better evaluation of the actual uncertainties and realistic limits of accuracy to be assessed. Such assessments are especially valuable when the accuracy improvements of benchmark referencing are to be included and extrapolations to new configurations are made

Measurement of the neutron spectrum of the Big Ten critical assembly by lithium-6 spectrometry

International Nuclear Information System (INIS)

De Leeuw-Gierts, G.; De Leeuw, S.; Hansen, G.E.; Helmick, H.H.

1979-01-01

The central neutron-flux spectrum of the Los Alamos Scientific Laboratory's critical assembly, Big Ten, was measured with a 6 Li spectrometer and techniques developed at the Centre d'Etude de L'Energie Nucleaire, Mol, as part of an experimental program to establish the characteristics of Big Ten

Measurement of the neutron spectrum of the Big Ten critical assembly by lithium-6 spectrometry

International Nuclear Information System (INIS)

Leeuw-Gierts, G. de; Leeuw, S. de

1980-01-01

The central neutron-flux spectrum of the Los Alamos Scientific Laboratory's critical assembly, Big Ten, was measured with a 6 Li spectrometer and techniques developed at the Centre d'Etude de l'Energie Nucleaire, Mol, as part of an experimental program to establish the characteristics of Big Ten

Calculation and analysis for a series of enriched uranium bare sphere critical assemblies

International Nuclear Information System (INIS)

Yang Shunhai

1994-12-01

The imported reactor fuel assembly MARIA program system is adapted to CYBER 825 computer in China Institute of Atomic Energy, and extensively used for a series of enriched uranium bare sphere critical assemblies. The MARIA auxiliary program of resonance modification MA is designed for taking account of the effects of resonance fission and absorption on calculated results. By which, the multigroup constants in the library attached to MARIA program are revised based on the U.S. Evaluated Nuclear Data File ENDF/B-IV, the related nuclear data files are replaced. And then, the reactor geometry buckling and multiplication factor are given in output tapes. The accuracy of calculated results is comparable with those of Monte Carlo and Sn method, and the agreement with experiment result is in 1%. (5 refs., 4 figs., 3 tabs.)

Study on neutron streaming effect in large fast critical assembly

International Nuclear Information System (INIS)

Takeda, Toshikazu; Yamaoka, Mitsuaki; Sakurai, Shungo; Tanimoto, Koichi; Abe, Yuhei

1981-03-01

A cell calculation method taking into account the neutron leakage from a cell and a transport calculation method treating the neutron streaming have been developed, and their applicability has been investigated. In the cell calculation method, the neutron leakage in the perpendicular direction to plates was treated by introducing an albedo collision probability which is a first-flight collision probability incorporating albedos at cell boundaries, and that in the parallel direction was treated by the pseudo absorption method. The use of the albedo collision probability made it possible to calculate the flux tilt in a cell exactly. This cell calculation method was applied to two slab models where fuel drawers were stacked in perpendicular and parallel directions to plates. Cell averaged cross sections calculated by the proposed method agreed well with those obtained from exact transport calculations treating the plate-wise heterogeneity, while the infinite cell calculation and the conventional pseudo absorption method produced about 2% errors in the cell-averaged cross sections. The cell-averaging procedure for control-rod channels was also proposed, and this method was applied to the calculation of control-rod worths and control-rod position worths. A transport calculation method based on the response matrix method has been proposed to treat the neutron streaming in fast critical assemblies directly. A response matrix code in two dimensional XY geometry RES2D was made. The accuracy of response matrices obtained from the RES2D code was checked by applying it to a slab cell and by comparing cell-averaged cross sections and k-infinity with those from a reference cell calculation based on the collision probability. The agreement of the results was good, and it was found that the response matrix method is very promising for the treatment of the neutron streaming in fast critical assemblies. (author)

Analytical analyses of startup measurements associated with the first use of LEU fuel in Romania's 14-MW TRIGA reactor

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.; Ciocanescu, M.

1992-01-01

The 14-MW TRIGA steady state reactor (SSR) is located in Pitesti, Romania. Beginning with an HEU core (10 wt% U), the reactor first went critical in November 1979 but was shut down ten years later because of insufficient excess reactivity. Last November the Institute for Nuclear Research (INR), which operates the SSR, received from the ANL RERTR program a shipment of 125 LEU pins fabricated by General Atomics and of the same geometry as the original fuel but with an enrichment of 19.7% 235U and a loading of 45 wt% U. Using 100 of these pins, four LEU clusters, each containing a 5 x 5 square array of fuel rods, were assembled. These four LEU clusters replaced the four most highly burned HEU elements in the SSR. The reactor resumed operations last February with a 35-element mixed HEU/LEU core configuration. In preparation for full power operation of the SSR with this mixed HEU/LEU core, a number of measurements were made. These included control rod calibrations, excess reactivity determinations, worths of experiment facilities, reaction rate distributions, and themocouple measurements of fuel temperatures as a function of reactor power. This paper deals with a comparison of some of these measured reactor parameters with corresponding analytical calculations

Criticality Benchmark Results Using Various MCNP Data Libraries

International Nuclear Information System (INIS)

Frankle, Stephanie C.

1999-01-01

A suite of 86 criticality benchmarks has been recently implemented in MCNPtrademark as part of the nuclear data validation effort. These benchmarks have been run using two sets of MCNP continuous-energy neutron data: ENDF/B-VI based data through Release 2 (ENDF60) and the ENDF/B-V based data. New evaluations were completed for ENDF/B-VI for a number of the important nuclides such as the isotopes of H, Be, C, N, O, Fe, Ni, 235,238 U, 237 Np, and 239,240 Pu. When examining the results of these calculations for the five manor categories of 233 U, intermediate-enriched 235 U (IEU), highly enriched 235 U (HEU), 239 Pu, and mixed metal assembles, we find the following: (1) The new evaluations for 9 Be, 12 C, and 14 N show no net effect on k eff ; (2) There is a consistent decrease in k eff for all of the solution assemblies for ENDF/B-VI due to 1 H and 16 O, moving k eff further from the benchmark value for uranium solutions and closer to the benchmark value for plutonium solutions; (3) k eff decreased for the ENDF/B-VI Fe isotopic data, moving the calculated k eff further from the benchmark value; (4) k eff decreased for the ENDF/B-VI Ni isotopic data, moving the calculated k eff closer to the benchmark value; (5) The W data remained unchanged and tended to calculate slightly higher than the benchmark values; (6) For metal uranium systems, the ENDF/B-VI data for 235 U tends to decrease k eff while the 238 U data tends to increase k eff . The net result depends on the energy spectrum and material specifications for the particular assembly; (7) For more intermediate-energy systems, the changes in the 235,238 U evaluations tend to increase k eff . For the mixed graphite and normal uranium-reflected assembly, a large increase in k eff due to changes in the 238 U evaluation moved the calculated k eff much closer to the benchmark value. (8) There is little change in k eff for the uranium solutions due to the new 235,238 U evaluations; and (9) There is little change in k eff

Numerical verification of the theory of coupled reactors for a deuterium critical assembly using MCNP5

International Nuclear Information System (INIS)

Hussein, M.S.; Bonin, H.W.; Lewis, B.J.

2013-01-01

The theory of multipoint coupled reactors developed by multi-group transport is verified by using the probabilistic transport code MCNP5. The verification was performed by calculating the multiplication factors (or criticality factors) and coupling coefficients for a two-region test reactor known as Deuterium Critical Assembly, (DCA). The variations of the criticality factors and the coupling coefficients were investigated by changing of the water levels in the inner and outer cores. The numerical results of the model developed with MCNP5 code were validated and verified against published results and the mathematical model based on coupled reactor theory. (author)

Numerical verification of the theory of coupled reactors for a deuterium critical assembly using MCNP5

Energy Technology Data Exchange (ETDEWEB)

Hussein, M.S.; Bonin, H.W.; Lewis, B.J., E-mail: mohamed.hussein@rmc.ca, E-mail: bonin-h@rmc.ca, E-mail: lewis-b@rmc.ca [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada)

2013-07-01

The theory of multipoint coupled reactors developed by multi-group transport is verified by using the probabilistic transport code MCNP5. The verification was performed by calculating the multiplication factors (or criticality factors) and coupling coefficients for a two-region test reactor known as Deuterium Critical Assembly, (DCA). The variations of the criticality factors and the coupling coefficients were investigated by changing of the water levels in the inner and outer cores. The numerical results of the model developed with MCNP5 code were validated and verified against published results and the mathematical model based on coupled reactor theory. (author)

Monte Carlo cross section testing for thermal and intermediate 235U/238U critical assemblies, ENDF/B-V vs ENDF/B-VI

International Nuclear Information System (INIS)

Weinman, J.P.

1997-06-01

The purpose of this study is to investigate the eigenvalue sensitivity to changes in ENDF/B-V and ENDF/B-VI cross section data sets by comparing RACER vectorized Monte Carlo calculations for several thermal and intermediate spectrum critical experiments. Nineteen Oak Ridge and Rocky Flats thermal solution benchmark critical assemblies that span a range of hydrogen-to- 235 U (H/U) concentrations (2052 to 27.1) and above-thermal neutron leakage fractions (0.555 to 0.011) were analyzed. In addition, three intermediate spectrum critical assemblies (UH3-UR, UH3-NI, and HISS-HUG) were studied

IRT‑Sofia, HEU to LEU conversion: regulatory approval tasks solution overview

International Nuclear Information System (INIS)

Mitev, Mladen; Belousov, Sergey; Dimitrov, Dobromir

2014-01-01

The HEU to LEU conversion of the IRT–Sofia research reactor of the Institute for Nuclear Research and Nuclear Energy of the Bulgarian Academy of Sciences was jointly studied with the Argonne National Laboratory as a part of the RERTR Programme. The main purpose of the collaboration consisted in accomplishment of safety analyses and preparation of documents used for regulatory approval tasks solution. The main steps and results which are fundamental for the preparation of IRT–Sofia Safety Analyses Report including Operating Limits and Conditions are presented in this paper. The documents prepared by INRNE in accordance with the European nuclear safety requirements and IAEA recommendations were submitted for approval to the Bulgarian Nuclear Regulatory Agency at the end of 2010. Key words: research reactor, safety analyses report, Nuclear Regulatory Agency

Characterization of neutron leakage probability, k /SUB eff/ , and critical core surface mass density of small reactor assemblies through the Trombay criticality formula

International Nuclear Information System (INIS)

Kumar, A.; Rao, K.S.; Srinivasan, M.

1983-01-01

The Trombay criticality formula (TCF) has been derived by incorporating a number of well-known concepts of criticality physics to enable prediction of changes in critical size or k /SUB eff/ following alterations in geometrical and physical parameters of uniformly reflected small reactor assemblies characterized by large neutron leakage from the core. The variant parameters considered are size, shape, density and diluent concentration of the core, and density and thickness of the reflector. The effect of these changes (except core size) manifests, through sigma /SUB c/ the critical surface mass density of the ''corresponding critical core,'' that sigma, the massto-surface-area ratio of the core,'' is essentially a measure of the product /rho/ extended to nonspherical systems and plays a dominant role in the TCF. The functional dependence of k /SUB eff/ on sigma/sigma /SUB c/ , the system size relative to critical, is expressed in the TCF through two alternative representations, namely the modified Wigner rational form and, an exponential form, which is given

Solution High-Energy Burst Assembly (SHEBA) results from subprompt critical experiments with uranyl fluoride fuel

International Nuclear Information System (INIS)

Cappiello, C.C.; Butterfield, K.B.; Sanchez, R.G.

1997-10-01

The Solution High-Energy Burst Assembly (SHEBA) was originally constructed during 1980 and was designed to be a clean free-field geometry, right-circular, cylindrically symmetric critical assembly employing U(5%)O 2 F 2 solution as fuel. A second version of SHEBA, employing the same fuel but equipped with a fuel pump and shielding pit, was commissioned in 1993. This report includes data and operating experience for the 1993 SHEBA only. Solution-fueled benchmark work focused on the development of experimental measurements of the characterization of SHEBA; a summary of the results are given. A description of the system and the experimental results are given in some detail in the report. Experiments were designed to: (1) study the behavior of nuclear excursions in a low-enrichment solution, (2) evaluate accidental criticality alarm detectors for fuel-processing facilities, (3) provide radiation spectra and dose measurements to benchmark radiation transport calculations on a low-enrichment solution system similar to centrifuge enrichment plants, and (4) provide radiation fields to calibrate personnel dosimetry. 15 refs., 37 figs., 10 tabs

Neutron data testing for plutonium isotopes in experiments at fast critical assemblies

International Nuclear Information System (INIS)

Bednyakov, S.M.; Dulin, V.A.; Manturov, G.N.; Mozhaev, V.K.; Semenov, M.Yu.; Tsibulya, A.M.

1996-01-01

Experimental results on checking neutron data, obtained at the fast critical assemblies, are presented. They constitute sufficiently large collection of data making it possible to test nuclear neutron constants of plutonium isotopes for the new system of group constants BNAB-93. The work contains comparison of the measurement results on average fission cross section ratios and reactivity coefficients ratios for 239,240,241 Pu (to 235 U) with calculational data, obtained on the basis of the new testing system of the BNAB-93 group constants system. 14 refs., 6 figs

Analysis of Np-237 ENDF for the theortical interpretation of critical assembly experiments.

Energy Technology Data Exchange (ETDEWEB)

Mihaila, B. (Bogdan); Chadwick, M. B. (Mark B.); MacFarlane, R. E. (Robert E.); Kawano, T. (Toshihiko)

2004-01-01

We report on the present status of our effort toward an improved Np-237 evaluated nuclear data file (ENDF). The aim here is to bridge the gap between calculated and observed k-eff values, as measured at the Np-U critical assembly at LANL, TA-18. As such, we perform a critical analysis of the existing body of experimental data and recommended evaluations. We are targeting in principal the fission nu-bar and cross section in Np-237, as well as the inelastic scattering which is particularly important since Np-237 is a threshold fissioner. This analysis will be employed in a future sensitivity study of the calculated k-eff with respect to variations of the afore mentioned nuclear data.

Nuclear and radiological safety in the substitution process of the fuel HEU to LEU 30/20 in the Reactor TRIGA Mark III of the ININ

International Nuclear Information System (INIS)

Hernandez G, J.

2012-10-01

Inside the safety initiative in the international ambit, with the purpose of reducing the risks associated with the use of high enrichment nuclear fuels (HEU) for different proposes to the peaceful uses of the nuclear energy, Mexico contributes by means of the substitution of the high enrichment fuel HEU for low enrichment fuel LEU 30/20 in the TRIGA Mark III Reactor, belonging to Instituto Nacional de Investigaciones Nucleares (ININ). The conversion process was carried out by means of the following activities: analysis of the proposed core, reception and inspection of the fuel LEU 30/20, the discharge of the fuels of the mixed reactor core, shipment of the fuels HEU fresh and irradiated to the origin country, reload activities with the fuels LEU 30/20 and parameters measurement of the core operation. In order to maintaining the personnel's integrity and infrastructure associated to the Reactor, during the whole process the measurements of nuclear and radiological safety were controlled to detail, in execution with the license requirements of the installation. This work describes the covering activities and radiological inspections more relevant, as well as the measurements of radiological control implemented with base in the estimate of the equivalent dose of the substitution process. (Author)

Why does the need of HEU for high flux research reactors remain?

International Nuclear Information System (INIS)

Glaeser, W.

1991-01-01

It has shown that high performance high flux reactors need an ongoing supply of highly enriched uranium. The new fuel materials in their highly enriched version offer prospective for advanced and better neutron sources vital for the future of neutron research. This is another very attractive result of the RERTR programme. One-sided restriction would only provide marginal or no values for research. If we adopt the sometimes expressed views that high enriched RERTR developed fuel should only be made available when unique benefits to mankind could be obtained, then certainly basic research at the forefront belongs to this category. HEU would only pose theoretical difficulties, if it would remain under proper safeguards and obviously this is the way to be pursued. (orig.)

Characterization of the CALIBAN Critical Assembly Neutron Spectra using Several Adjustment Methods Based on Activation Foils Measurement

OpenAIRE

Casoli Pierre; Grégoire Gilles; Rousseau Guillaume; Jacquet Xavier; Authier Nicolas

2016-01-01

CALIBAN is a metallic critical assembly managed by the Criticality, Neutron Science and Measurement Department located on the French CEA Center of Valduc. The reactor is extensively used for benchmark experiments dedicated to the evaluation of nuclear data, for electronic hardening or to study the effect of the neutrons on various materials. Therefore CALIBAN irradiation characteristics and especially its central cavity neutron spectrum have to be very accurately evaluated. In order to streng...

Monte Carlo Depletion with Critical Spectrum for Assembly Group Constant Generation

International Nuclear Information System (INIS)

Park, Ho Jin; Joo, Han Gyu; Shim, Hyung Jin; Kim, Chang Hyo

2010-01-01

The conventional two-step procedure has been used in practical nuclear reactor analysis. In this procedure, a deterministic assembly transport code such as HELIOS and CASMO is normally to generate multigroup flux distribution to be used in few-group cross section generation. Recently there are accuracy issues related with the resonance treatment or the double heterogeneity (DH) treatment for VHTR fuel blocks. In order to mitigate the accuracy issues, Monte Carlo (MC) methods can be used as an alternative way to generate few-group cross sections because the accuracy of the MC calculations benefits from its ability to use continuous energy nuclear data and detailed geometric information. In an earlier work, the conventional methods of obtaining multigroup cross sections and the critical spectrum are implemented into the McCARD Monte Carlo code. However, it was not complete in that the critical spectrum is not reflected in the depletion calculation. The purpose of this study is to develop a method to apply the critical spectrum to MC depletion calculations to correct for the leakage effect in the depletion calculation and then to examine the MC based group constants within the two-step procedure by comparing the two-step solution with the direct whole core MC depletion result

Simulation of reactor noise analysis measurement for light-water critical assembly TCA using MCNP-DSP

International Nuclear Information System (INIS)

Yamamoto, Toshihiro; Sakurai, Kiyoshi; Tonoike, Kotaro; Miyoshi, Yoshinori

2001-01-01

Reactor noise analysis methods using Monte Carlo technique have been proposed and developed in the field of nuclear criticality safety. The Monte Carlo simulation for noise analysis can be made by simulating physical phenomena in the course of neutron transport in a nuclear fuel as practically as possible. MCNP-DSP was developed by T. Valentine of ORNL for this purpose and it is a modified version of MCNP-4A. The authors applied this code to frequency analysis measurements performed in light-water critical assembly TCA. Prompt neutron generation times for critical and subcritical cores were measured by doing the frequency analysis of detector signals. The Monte Carlo simulations for these experiments were carried out using MCNP-DSP, and prompt neutron generation times were calculated. (author)

Studies of spatial decoupling in heterogeneous LMFBR critical assemblies

International Nuclear Information System (INIS)

Brumbach, S.B.; Goin, R.W.; Carpenter, S.G.

1984-01-01

Recent measurements at the Zero Power Plutonium Reactor have studied the spatial decoupling in large, heterogeneous assemblies. These assemblies exhibited a significantly greater degree of decoupling than previous homogeneous assemblies of similar size. The flux distributions in these heterogeneous assemblies were very sensitive reactivity perturbations, and perturbed flux distributions were achieved relatively slowly. Decoupling was investigated using rod-drop, boron-oscillator and noise-coherence techniques which emphasized different times following the perturbations. Reactivity changes could be measured by analyzing the power history from a single detector using inverse kinetics methods with the assumption of an instantaneous efficiency change for the detector. For assemblies more decoupled than ZPPR-13, the instantaneous efficiency change assumption begins to be invalid

Colloidal Self-Assembly Driven by Deformability & Near-Critical Phenomena

NARCIS (Netherlands)

Evers, C.H.J.|info:eu-repo/dai/nl/338775188

2016-01-01

Self-assembly is the spontaneous formation of patterns or structures without human intervention. This thesis aims to increase our understanding of self-assembly. In self-assembly of proteins, the building blocks are very small and complex. Consequently, grasping the basic principles that drive the

Method of preventing criticality of fresh fuel assembly in storage facility

International Nuclear Information System (INIS)

Kawamura, Makoto.

1990-01-01

With an aim of improving the operation efficiency of a reactor, extention of the operation cycle by increasing U 235 enrichment degree of fuel uranium is planned. However, along with the increase of the enrichment degree of the fuel uranium, there occurs a problem of criticality upon fuel handling. Then, in the present invention, boric acid incorporating B-10 of great neutron absorption effect are packed with water soluble polymeric materials which are further packed with a fuel packing sheet, or the water soluble polymeric materials incorporating boric acids are packed with fuel packing sheets which are disposed to a fresh fuel assembly and stored in a store house as they are. The fuel packing sheet is a perforated sheet having a plurality of water intruding pores. Then, if water should intrude to the store house accidentally, the water soluble polymeric materials are dissolved, so that the intruded water is converted into aqueous boric acid easily and absorbs neutrons effectively to thereby attain the prevention of criticality. (T.M.)

Autoradiographic technique for rapid inventory of plutonium-containing fast critical assembly fuel

International Nuclear Information System (INIS)

Brumbach, S.B.; Perry, R.B.

1977-10-01

A nondestructive autoradiographic technique is described which can provide a verification of the piece count and the plutonium content of plutonium-containing fuel elements. This technique uses the spontaneously emitted gamma rays from plutonium to form images of fuel elements on photographic film. Autoradiography has the advantage of providing an inventory verification without the opening of containers or the handling of fuel elements. Missing fuel elements, substitution of nonradioactive material, and substitution of elements of different size are detectable. Results are presented for fuel elements in various storage configurations and for fuel elements contained in a fast critical assembly

Educational use of research reactor (KUR) and critical assembly (KUCA) at Kyoto University

International Nuclear Information System (INIS)

Misawa, Tsuyoshi; Unesaki, Hironobu; Ichihara, Chihiro; Pyeon, Cheol Ho; Shiroya, Seiji

2005-01-01

At Kyoto University Research Reactor Institute, a research reactor of 5MW (KUR) and a critical assembly (KUCA) have been used for educational purpose to train undergraduate or graduate students. Using KUR, basic experiments for neutron applications have been carried out, and KUCA has been used for the education of nuclear engineering and technology. Especially, using KUCA, a joint reactor laboratory course of graduate level is offered every summer since 1975 by nine associated Japanese universities, and more than 2200 students attended this course

An investigative approach to explore optimum assembly process design for annular targets carrying LEU foil

Science.gov (United States)

Hoyer, Annemarie

Technetium-99m is the most widely used nuclear isotope in the medical field, with nearly 80 to 85% of all diagnostic imaging procedures. The daughter isotope of molybdenum-99 is currently produced using weapons-grade uranium. A suggested design for aluminum targets carrying low-enriched uranium (LEU) foil is presented for the fulfillment of eliminating highly enriched uranium (HEU) for medical isotope production. The assembly process that this research focuses on is the conventional draw-plug process which is currently used and lastly the sealing process. The research is unique in that it is a systematic approach to explore the optimal target assembly process to produce those targets with the required quality and integrity. Conducting 9 parametric experiments, aluminum tubes with a nickel foil fission-barrier and a surrogate stainless steel foil are assembled, welded and then examined to find defects, to determine residual stresses, and to find the best cost-effective target dimensions. The experimental design consists of 9 assembly combinations that were found through orthogonal arrays in order to explore the significance of each factor. Using probabilistic modeling, the parametric study is investigated using the Taguchi method of robust analysis. Depending on the situation, optimal conditions may be a nominal, a minimized or occasionally a maximized condition. The results will provide the best target design and will give optimal quality with little or no assembly defects.

Criticality safety evaluation for TWR-S fuel assembly transportation using TK-S16 containers

International Nuclear Information System (INIS)

Pesic, M.P.; Steljic, M.M.; Antic, D.P.

2002-01-01

Criticality safety issues, concerning transportation of fresh high-enriched uranium fuel elements (TWR-S fuel assembly type) with Russian containers TK-S16, are objects of study in this paper. Three-dimensional (3D) models of fuel element and container were made, based upon their well-known geometry and material structure. The way to pack fuel elements in a bundle inside of the container is proposed. Calculations were done by MCNP4B2 computer code. This Monte Carlo criticality code determined the effective multiplication factor from the cross-section data and specific geometry data. This evaluation demonstrated the subcriticality of a single package and an array of packages during normal conditions of transport and various hypothetical accident conditions. (author)

Characterization of the Caliban and Prospero Critical Assemblies Neutron Spectra for Integral Measurements Experiments

Science.gov (United States)

Casoli, P.; Authier, N.; Jacquet, X.; Cartier, J.

2014-04-01

Caliban and Prospero are two highly enriched uranium metallic core reactors operated on the CEA Center of Valduc. These critical assemblies are suitable for integral experiments, such as fission yields measurements or perturbation measurements, which have been carried out recently on the Caliban reactor. Different unfolding methods, based on activation foils and fission chambers measurements, are used to characterize the reactor spectra and especially the Caliban spectrum, which is very close to a pure fission spectrum.

Alternative dispositioning methods for HEU spent nuclear fuel at the Savannah River Site

International Nuclear Information System (INIS)

Krupa, J.F.; McKibben, J.M.; Parks, P.B.; DuPont, M.E.

1995-01-01

The United States has a strong policy on prevention of the international spread of nuclear weapons. This policy was announced in Presidential Directive PDD-13 and summarized in a White House press release September 27, 1993. Two cornerstones of this policy are: seek to eliminate where possible the accumulation of stockpiles of highly- enriched uranium or plutonium; propose hor-ellipsis prohibiting the production of highly-enriched uranium (HEU) or plutonium for nuclear explosives purposes or outside international safeguards. The Department of Energy is currently struggling to devise techniques that safely and efficiently dispose of spent nuclear fuel (SNF) while satisfying national non-proliferation policies. SRS plans and proposals for disposing of their SNF are safe and cost effective, and fully satisfy non-proliferation objectives

Mechanics of a crushable pebble assembly using discrete element method

International Nuclear Information System (INIS)

Annabattula, R.K.; Gan, Y.; Zhao, S.; Kamlah, M.

2012-01-01

The influence of crushing of individual pebbles on the overall strength of a pebble assembly is investigated using discrete element method. An assembly comprising of 5000 spherical pebbles is assigned with random critical failure energies with a Weibull distribution in accordance with the experimental observation. Then, the pebble assembly is subjected to uni-axial compression (ε 33 =1.5%) with periodic boundary conditions. The crushable pebble assembly shows a significant difference in stress–strain response in comparison to a non-crushable pebble assembly. The analysis shows that a ideal plasticity like behaviour (constant stress with increase in strain) is the characteristic of a crushable pebble assembly with sudden damage. The damage accumulation law plays a critical role in determining the critical stress while the critical number of completely failed pebbles at the onset of critical stress is independent of such a damage law. Furthermore, a loosely packed pebble assembly shows a higher crush resistance while the critical stress is insensitive to the packing factor (η) of the assembly.

Supplementary neutron-flux calculations for the ORNL Pool Critical Assembly Pressure Vessel Facility

International Nuclear Information System (INIS)

Maudlin, P.J.; Maerker, R.E.

1982-01-01

A three-dimensional Monte Carlo calculation using the MORSE code was performed to validate a procedure previously adopted in the ORNL discrete ordinate analysis of measurements made in the ORNL Pool Critical Assembly Pressure Vessel Facility. The results of these flux calculations agree, within statistical undertainties of about 5%, with those obtained from a discrete ordinate analysis employing the same procedure. This study therefore concludes that the procedure for combining several one- and two-dimensional discrete ordinate calculations into a three-dimensional flux is sufficiently accurate that it does not account for the existing discrepancies observed between calculations and measurements in this facility

Supplementary neutron flux calculations for the ORNL pool critical assembly pressure vessel facility

Energy Technology Data Exchange (ETDEWEB)

Maerker, R.E.; Maudlin, P.J.

1981-02-01

A three-dimensional Monte Carlo calculation was performed to estimate the neutron flux in the 8/7 configuration of the ORNL Pool Critical Assembly Pressure Vessel Facility. The calculational tool was the multigroup transport code MORSE operated in the adjoint mode. The MORSE flux results compared well with those using a previously adopted procedure for constructing a three-dimensional flux from one- and two-dimensional discrete ordinates calculations using the DOT-IV code. This study concluded that use of these discrete ordinates constructions in previous calculations is sufficiently accurate and does not account for the existing discrepancies between calculation and experiment.

Supplementary neutron-flux calculations for the ORNL Pool Critical Assembly Pressure Vessel Facility

Energy Technology Data Exchange (ETDEWEB)

Maudlin, P.J.; Maerker, R.E.

1982-01-01

A three-dimensional Monte Carlo calculation using the MORSE code was performed to validate a procedure previously adopted in the ORNL discrete ordinate analysis of measurements made in the ORNL Pool Critical Assembly Pressure Vessel Facility. The results of these flux calculations agree, within statistical undertainties of about 5%, with those obtained from a discrete ordinate analysis employing the same procedure. This study therefore concludes that the procedure for combining several one- and two-dimensional discrete ordinate calculations into a three-dimensional flux is sufficiently accurate that it does not account for the existing discrepancies observed between calculations and measurements in this facility.

Supplementary neutron flux calculations for the ORNL pool critical assembly pressure vessel facility

International Nuclear Information System (INIS)

Maerker, R.E.; Maudlin, P.J.

1981-02-01

A three-dimensional Monte Carlo calculation was performed to estimate the neutron flux in the 8/7 configuration of the ORNL Pool Critical Assembly Pressure Vessel Facility. The calculational tool was the multigroup transport code MORSE operated in the adjoint mode. The MORSE flux results compared well with those using a previously adopted procedure for constructing a three-dimensional flux from one- and two-dimensional discrete ordinates calculations using the DOT-IV code. This study concluded that use of these discrete ordinates constructions in previous calculations is sufficiently accurate and does not account for the existing discrepancies between calculation and experiment

Pool critical assembly pressure vessel facility benchmark

International Nuclear Information System (INIS)

Remec, I.; Kam, F.B.K.

1997-07-01

This pool critical assembly (PCA) pressure vessel wall facility benchmark (PCA benchmark) is described and analyzed in this report. Analysis of the PCA benchmark can be used for partial fulfillment of the requirements for the qualification of the methodology for pressure vessel neutron fluence calculations, as required by the US Nuclear Regulatory Commission regulatory guide DG-1053. Section 1 of this report describes the PCA benchmark and provides all data necessary for the benchmark analysis. The measured quantities, to be compared with the calculated values, are the equivalent fission fluxes. In Section 2 the analysis of the PCA benchmark is described. Calculations with the computer code DORT, based on the discrete-ordinates method, were performed for three ENDF/B-VI-based multigroup libraries: BUGLE-93, SAILOR-95, and BUGLE-96. An excellent agreement of the calculated (C) and measures (M) equivalent fission fluxes was obtained. The arithmetic average C/M for all the dosimeters (total of 31) was 0.93 ± 0.03 and 0.92 ± 0.03 for the SAILOR-95 and BUGLE-96 libraries, respectively. The average C/M ratio, obtained with the BUGLE-93 library, for the 28 measurements was 0.93 ± 0.03 (the neptunium measurements in the water and air regions were overpredicted and excluded from the average). No systematic decrease in the C/M ratios with increasing distance from the core was observed for any of the libraries used

Criticality of a 237Np sphere

International Nuclear Information System (INIS)

Sanchez, Rene; Loaiza, David; Kimpland, Robert; Hayes, David; Cappiello, Charlene; Chadwick, Mark

2006-01-01

this paper establish the critical masses of neptunium surrounded with HEU and reflected by various reflectors. The primary purpose of these experiments is to provide criticality data that will be used to validate models in support of decommissioning activities at the Savannah River plant and establish well defined subcritical mass limits that can be used in the transportation of these materials to other Department of Energy facilities. Finally, a critical experiment using an α-phase plutonium sphere surrounded with similar HEU shells and using the same set-up used for the neptunium experiments was performed to validate plutonium and uranium cross section data. (authors)

Combined use of the RPI [Rensselaer Polytechnic Institute] reactor for training and critical experiments

International Nuclear Information System (INIS)

Harris, D.R.; Rohr, R.R.; Rodriguez-Vera, F.

1990-01-01

The Rensselaer Polytechnic Institute (RPI) reactor critical facility (RCF) has provided educational and research opportunities for RPI and other students for >25 yr. The RCF was built by the American Locomotive Company (ALCO) in the 1950s as a critical facility in support of the army package power reactor program, and, when ALCO went out of business in 1964, the RCF was acquired by RPI. Since that time, RPI has operated the RCF primarily in a teaching mode in the nuclear engineering department, although reactor research, activation analyses, and reactivity assays have been carried out as well. Until recently, the RCF was fueled by plates containing highly enriched uranium as a cermet in stainless steel. This highly enriched uranium (HEU) fuel was replaced recently by 4.81 wt% enriched UO 2 high-density pellets clad in stainless steel rods. The use of these SPERT (F1) fuel rods in the RCF provided a cost-effective method for conversion of the core from HEU to low-enriched uranium and for enhancement of the RCF training and research program. The RCF is the only facility in the United States that provides reactor training on a core containing fuel that is similar to that used in power industry light water reactors (LWRs). Moreover, the RCF is the only facility in the United States currently available for supplying critical experimental data in support of the LWR power industry. Thus, the RCF is in a unique position to carry out important training and research services consistent with RPI's nuclear engineering objectives

Formation of clusters composed of C60 molecules via self-assembly in critical fluids

International Nuclear Information System (INIS)

Fukuda, Takahiro; Ishii, Koji; Kurosu, Shunji; Whitby, Raymond; Maekawa, Toru

2007-01-01

Fullerenes are promising candidates for intelligent, functional nanomaterials because of their unique mechanical, electronic and chemical properties. However, it is necessary to invent some efficient but relatively simple methods of producing structures composed of fullerenes for the development of nanomechatronic, nanoelectronic and biochemical devices and sensors. In this paper, we show that various structures such as straight fibres, networks formed by fibres, wide sheets and helical structures, which are composed of C 60 molecules, are created by placing C 60 -crystals in critical ethane, carbon dioxide and xenon even though C 60 molecules do not dissolve or disperse in the above fluids. It is supposed, judging by the intermolecular potentials between C 60 and C 60 , between C 60 and ethane, and between ethane and ethane, that C 60 -clusters grow with the assistance of solvent molecules, which are trapped between C 60 molecules under critical conditions. This room-temperature self-assembly cluster growth process in critical fluids may open up a new methodology of forming structures built up with fullerenes without the need for any ultra-fine processing technologies

Onset of self-assembly

International Nuclear Information System (INIS)

Chitanvis, S.M.

1998-01-01

We have formulated a theory of self-assembly based on the notion of local gauge invariance at the mesoscale. Local gauge invariance at the mesoscale generates the required long-range entropic forces responsible for self-assembly in binary systems. Our theory was applied to study the onset of mesostructure formation above a critical temperature in estane, a diblock copolymer. We used diagrammatic methods to transcend the Gaussian approximation and obtain a correlation length ξ∼(c-c * ) -γ , where c * is the minimum concentration below which self-assembly is impossible, c is the current concentration, and γ was found numerically to be fairly close to 2/3. The renormalized diffusion constant vanishes as the critical concentration is approached, indicating the occurrence of critical slowing down, while the correlation function remains finite at the transition point. copyright 1998 The American Physical Society

Extrapolated experimental critical parameters of unreflected and steel-reflected massive enriched uranium metal spherical and hemispherical assemblies

International Nuclear Information System (INIS)

Rothe, R.E.

1997-12-01

Sixty-nine critical configurations of up to 186 kg of uranium are reported from very early experiments (1960s) performed at the Rocky Flats Critical Mass Laboratory near Denver, Colorado. Enriched (93%) uranium metal spherical and hemispherical configurations were studied. All were thick-walled shells except for two solid hemispheres. Experiments were essentially unreflected; or they included central and/or external regions of mild steel. No liquids were involved. Critical parameters are derived from extrapolations beyond subcritical data. Extrapolations, rather than more precise interpolations between slightly supercritical and slightly subcritical configurations, were necessary because experiments involved manually assembled configurations. Many extrapolations were quite long; but the general lack of curvature in the subcritical region lends credibility to their validity. In addition to delayed critical parameters, a procedure is offered which might permit the determination of prompt critical parameters as well for the same cases. This conjectured procedure is not based on any strong physical arguments

Core conversion anaylses for the Portuguese Research Reactor

International Nuclear Information System (INIS)

Matos, J.E.; Stevens, J.G.; Feldman, E.E.; Stillman, J.A.; Dunn, F.E.; Kalimullah, K.; Marques, J.G.; Barradas, N.P.; Ramos, A.R.; Kling, A.

2006-01-01

Design and safety analyses are presented for conversion of the Portuguese Research Reactor (RPI) from the use of HEU fuel to the use of LEU fuel. The analyses were performed jointly by the RERTR Program at the Argonne National Laboratory (ANL) and the Instituto Tecnologico e Nuclear (ITN). The LEU fuel assembly design uses U 3 Si 2 -Al dispersion fuel with 4.8 g U/cm 3 and is very similar to the HEU fuel design. The results of neutronic studies, steady-state thermal-hydraulic analyses, accident analyses, and revisions to the Operating Limits and Conditions demonstrate that the RPI reactor can be operated safely with the new LEU fuel assemblies. Delivery of the LEU fuel is expected around the end of 2006, with conversion in early 2007. The HEU fuel is planned to be returned to the US in 2008.

Effect of a dual-purpose cask payload increment of spent fuel assemblies from VVER 1000 Bushehr Nuclear Power Plant on basket criticality

International Nuclear Information System (INIS)

Rezaeian, M.; Kamali, J.

2017-01-01

Dual-purpose casks can be utilized for dry interim storage and transportation of the highly radioactive spent fuel assemblies (SFAs) of Bushehr Nuclear Power Plant (NPP). Criticality safety analysis was carried out using the MCNP code for the cask containing 12, 18, or 19 SFAs. The basket materials of borated stainless steel and Boral (Al-B_4C) were investigated, and the minimum required receptacle pitch of the basket was determined. - Highlights: • Criticality safety analysis for a dual purpose cask was carried out. • The basket material of borated stainless steel and Boral were investigated. • Minimum receptacle pitch was determined for 12, 18, or 19 VVER 1000 spent fuel assemblies.

Test calculations of physical parameters of the TRX,BETTIS and MIT critical assemblies according to the TRIFON program

International Nuclear Information System (INIS)

Kochurov, B.P.

1980-01-01

Results of calculations of physical parameters characterizing the TRX, MIT and BETTIS critical assemblies obtained according to the program TRIFON are presented. The program TRIFON permits to calculate the space-energy neutron distribution in the multigroup approximation in a multizone cylindrical cell. Results of comparison of the TRX, BETTIS and MIT crytical assembly parameters with experimental data and calculational results according to the Monte Carlo method are presented as well. Deviations of the parameters are in the range of 1.5-2 of experimental errors. Data on the interference of uranium 238 levels in the resonant neutron absorption in the cell are given [ru

Reactor laboratory course for Korean under-graduate students in Kyoto University Critical Assembly (KUGSiKUCA)

International Nuclear Information System (INIS)

Pyeon, Cheol Ho; Misawa, Tsuyoshi; Unesaki, Hironobu; Ichihara, Chihiro; Shiroya, Seiji; Whang, Joo Ho; Kim, Myung Hyun

2005-01-01

The Reactor Laboratory Course for Korean Under-Graduate Students has been carried out at Kyoto University Critical Assembly of Japan. This course has been launched from fiscal year 2003 and has been founded by Ministry of Science and Technology of Korean Government. Since then, the total number of 43 Korean under-graduate students, who have majored in nuclear engineering of 6 universities in all over the Korea, has been taken part in this course. The reactor physics experiments have been performed in this course, such as Approach to criticality, Control rod calibration, Measurement of neutron flux and power calibration, and Educational reactor operation. As technical tour of Japan, nuclear site tour has been taken during their stay in Japan, such as PWR, FBR, nuclear fuel company and some institutes

Transmutation of uranium and thorium in the particle field of the Quinta sub-critical assembly

Science.gov (United States)

Hashemi-Nezhad, S. R.; Asquith, N. L.; Voronko, V. A.; Sotnikov, V. V.; Zhadan, Alina; Zhuk, I. V.; Potapenko, A.; Husak, Krystsina; Chilap, V.; Adam, J.; Baldin, A.; Berlev, A.; Furman, W.; Kadykov, M.; Khushvaktov, J.; Kudashkin, I.; Mar'in, I.; Paraipan, M.; Pronskih, V.; Solnyshkin, A.; Tyutyunnikov, S.

2018-03-01

The fission rates of natural uranium and thorium were measured in the particle field of Quinta, a 512 kg natural uranium target-blanket sub-critical assembly. The Quinta assembly was irradiated with deuterons of energy 4 GeV from the Nuclotron accelerator of the Joint Institute for Nuclear Research (JINR), Dubna, Russia. Fission rates of uranium and thorium were measured using Gamma spectroscopy and fission track techniques. The production rate of 239Np was also measured. The obtained experimental results were compared with Monte Carlo predictions using the MCNPX 2.7 code employing the physics and fission-evaporation models of INCL4-ABLA, CEM03.03 and LAQGSM03.03. Some of the neutronic characteristics of the Quinta are compared with the "Energy plus Transmutation (EpT)" subcritical assembly, which is composed of a lead target and natU blanket. This comparison clearly demonstrates the importance of target material, neutron moderator and reflector types on the performance of a spallation neutron driven subcritical system. As the dimensions of the Quinta are very close to those of an optimal multi-rod-uranium target, the experimental and Monte Carlo calculation results presented in this paper provide insights on the particle field within a uranium target as well as in Accelerator Driven Systems in general.

Multi-scale coarse-graining for the study of assembly pathways in DNA-brick self-assembly

Science.gov (United States)

Fonseca, Pedro; Romano, Flavio; Schreck, John S.; Ouldridge, Thomas E.; Doye, Jonathan P. K.; Louis, Ard A.

2018-04-01

Inspired by recent successes using single-stranded DNA tiles to produce complex structures, we develop a two-step coarse-graining approach that uses detailed thermodynamic calculations with oxDNA, a nucleotide-based model of DNA, to parametrize a coarser kinetic model that can reach the time and length scales needed to study the assembly mechanisms of these structures. We test the model by performing a detailed study of the assembly pathways for a two-dimensional target structure made up of 334 unique strands each of which are 42 nucleotides long. Without adjustable parameters, the model reproduces a critical temperature for the formation of the assembly that is close to the temperature at which assembly first occurs in experiments. Furthermore, the model allows us to investigate in detail the nucleation barriers and the distribution of critical nucleus shapes for the assembly of a single target structure. The assembly intermediates are compact and highly connected (although not maximally so), and classical nucleation theory provides a good fit to the height and shape of the nucleation barrier at temperatures close to where assembly first occurs.

Conversion of the Worcester Polytechnic Institute nuclear reactor to low enriched uranium

International Nuclear Information System (INIS)

Newton, T.H. Jr.

1991-01-01

The Training Reactor was converted to Low-Enriched Uranium (LEU) aluminide fuel in 1988 and 1989. Tests on the Highly-Enriched Uranium (HEU) core and LEU cores were performed and comparisons made. The testing consisted of critical loading, thermal neutron flux distribution, excess reactivity, regulating blade reactivity worth, and temperature coefficient of reactivity measurement. Comparisons between the LEU and HEU showed that the critical loading configurations were somewhat different with the HEU core consisting of 24 elements and the LEU core consisting of 21 1/3 elements with excess reactivities of 0.24% ΔK/K for the HEU and 0.16% for the LEU. Thermal neutron flux distributions showed similar trends in both the LEU and HEU cores. The regulating blade worth showed a larger LEU value due to thermal peaking in the blade region and temperature coefficients showed a more negative LEU value due to Doppler broadening. Low induced activity of the HEU fuel permitted shipment to the Westinghouse Savannah River Facility using DOT-6M type B containers on 8 August, 1989. (orig.)

CSER-00-007 Addendum 1 Criticality Safety Evaluation of Shippingport PWR Core 2 Blanket Fuel Assemblies at Lower Exposures

International Nuclear Information System (INIS)

WITTEKIND, W.D.

2001-01-01

This analysis meets the requirements of HNF-7098, Criticality Safety Program, (FH 2001a). HNF-7098 states that before starting a new operation with fissile material or before an existing operation is changed, it shall be determined that the entire process will be subcritical under both normal and credible abnormal conditions. To demonstrate the Incredibility Principle is satisfied, this Criticality Safety Evaluation Report (CSER) shows that the form or distribution is such that criticality is impossible. This evaluation demonstrated, that on the basis of effective 235 U enrichment, criticality is not possible. The minimum blanket assembly exposure is 4,375 MW t d/MTU for fissile material that is shown to fulfill the Incredibility Principle safety criterion on the basis of enrichment

KUCA critical experiments using MEU fuel (II)

Energy Technology Data Exchange (ETDEWEB)

Kanda, Keiji; Hayashi, Masatoshi; Shiroya, Seiji; Kobayashi, Keiji; Fukui, Hiroshi; Mishima, Kaichiro; Shibata, Toshikazu [Research Reactor Institute, Kyoto University, Kumatori-cho, Sennan-gun, Osaka (Japan)

1983-09-01

Due to mutual concerns in the USA and Japan about the proliferation potential of highly-enriched uranium (HEU), a joint study program I was initiated between Argonne National Laboratory (ANL and Kyoto University Research Reactor Institute (KURRI) in 1978. In accordance with the reduced enrichment for research and test reactor (RERTR) program, the alternatives were studied for reducing the enrichment of the fuel to be used in the Kyoto University High Flux Reactor (KUHFR). The KUHFR has a distinct feature in its core configuration it is a coupled-core. Each annular shaped core is light-water-moderated and placed within a heavy water reflector with a certain distance between them. The phase A reports of the joint ANL-KURRI program independently prepared by two laboratories in February 1979, 3,4 concluded that the use of medium-enrichment uranium (MEU, 45%) in the KUHFR is feasible, pending results of the critical experiments in the Kyoto University Critical Assembly (KUCA) 5 and of the burnup test in the Oak Ridge Research Reactor 6 (ORR). An application of safety review (Reactor Installation License) for MEU fuel to be used in the KUCA was submitted to the Japanese Government in March 1980, and a license was issued in August 1980. Subsequently, the application for 'Authorization before Construction' was submitted and was authorized in September 1980. Fabrication of MEU fuel-elements for the KUCA experiments by CERCA in France was started in September 1980, and was completed in March 1981. The critical experiments in the KUCA with MEU fuel were started on a single-core in May 1981 as a first step. The first critical state of the core using MEU fuel was achieved at 312 p.m. in May 12, 1981. After that, the reactivity effects of the outer side-plates containing boron burnable poison were measured. At Munich Meeting in Sept., 1981, we presented a paper on critical mass and reactivity of burnable poison in the MEU core. Since then we carried out the following experiments

KUCA critical experiments using MEU fuel (II)

International Nuclear Information System (INIS)

Kanda, Keiji; Hayashi, Masatoshi; Shiroya, Seiji; Kobayashi, Keiji; Fukui, Hiroshi; Mishima, Kaichiro; Shibata, Toshikazu

1983-01-01

Due to mutual concerns in the USA and Japan about the proliferation potential of highly-enriched uranium (HEU), a joint study program I was initiated between Argonne National Laboratory (ANL and Kyoto University Research Reactor Institute (KURRI) in 1978. In accordance with the reduced enrichment for research and test reactor (RERTR) program, the alternatives were studied for reducing the enrichment of the fuel to be used in the Kyoto University High Flux Reactor (KUHFR). The KUHFR has a distinct feature in its core configuration it is a coupled-core. Each annular shaped core is light-water-moderated and placed within a heavy water reflector with a certain distance between them. The phase A reports of the joint ANL-KURRI program independently prepared by two laboratories in February 1979, 3,4 concluded that the use of medium-enrichment uranium (MEU, 45%) in the KUHFR is feasible, pending results of the critical experiments in the Kyoto University Critical Assembly (KUCA) 5 and of the burnup test in the Oak Ridge Research Reactor 6 (ORR). An application of safety review (Reactor Installation License) for MEU fuel to be used in the KUCA was submitted to the Japanese Government in March 1980, and a license was issued in August 1980. Subsequently, the application for 'Authorization before Construction' was submitted and was authorized in September 1980. Fabrication of MEU fuel-elements for the KUCA experiments by CERCA in France was started in September 1980, and was completed in March 1981. The critical experiments in the KUCA with MEU fuel were started on a single-core in May 1981 as a first step. The first critical state of the core using MEU fuel was achieved at 312 p.m. in May 12, 1981. After that, the reactivity effects of the outer side-plates containing boron burnable poison were measured. At Munich Meeting in Sept., 1981, we presented a paper on critical mass and reactivity of burnable poison in the MEU core. Since then we carried out the following experiments

HEU benchmark calculations and LEU preliminary calculations for IRR-1

International Nuclear Information System (INIS)

Caner, M.; Shapira, M.; Bettan, M.; Nagler, A.; Gilat, J.

2004-01-01

We performed neutronics calculations for the Soreq Research Reactor, IRR-1. The calculations were done for the purpose of upgrading and benchmarking our codes and methods. The codes used were mainly WIMS-D/4 for cell calculations and the three dimensional diffusion code CITATION for full core calculations. The experimental flux was obtained by gold wire activation methods and compared with our calculated flux profile. The IRR-1 is loaded with highly enriched uranium fuel assemblies, of the plate type. In the framework of preparation for conversion to low enrichment fuel, additional calculations were done assuming the presence of LEU fresh fuel. In these preliminary calculations we investigated the effect on the criticality and flux distributions of the increase of U-238 loading, and the corresponding uranium density.(author)

Safe operation of research reactors and critical assemblies. Code of practice and annexes. 1984 ed

International Nuclear Information System (INIS)

1984-01-01

The safe operation of research reactors and critical assemblies (hereafter termed 'reactors') requires proper design, construction, management and supervision. This Code of Practice deals mainly with management and supervision. The provisions of the Code apply to the whole life of the reactor, including modification, updating and upgrading. The Code may be subject to revision in the light of experience and the state of technology. The Code is aimed at defining minimum requirements for the safe operation of reactors. Emphasis is placed on which safety requirements should be met rather than on specifying how these requirements may be met. The Code also provides guidance and information to persons and authorities responsible for the operation of reactors. The Code recommends that documents dealing with the operation of reactors and including safety analyses be prepared and submitted for review and approval to a regulatory body. Operation would be authorized on the understanding that it would comply with limits and conditions designed to ensure safety. The Code covers a wide range of reactor types, which gives rise to a variety of safety issues. Safety issues applicable to specific reactor types only (e.g. fast reactors) are not necessarily covered in this Code. Some of the recommendations in the Code are not directly applicable to critical assemblies. A recommendation may therefore be interpreted according to the type of reactor concerned. In such cases the words 'adequate' and 'appropriate' are used to mean 'adequate' or 'appropriate' for the type of reactor under consideration.

Rapid method of calculating the fluence and spectrum of neutrons from a critical assembly and the resulting dose

International Nuclear Information System (INIS)

Bessis, J.

1977-01-01

The proposed calculation method is unsophisticated but rapid. The first part (computer code CRITIC), which is based on the Fermi age equation, evaluates the number of neutrons per fission emitted from a moderated critical assembly and their energy spectrum. The second part (computer code NARCISSE), which uses the current albedo for concrete, evaluates the product of neutron reflection on the walls and calculates the fluence resulting at any point in the room and its energy distribution by 21 groups. The results obtained are shown to compare satisfactorily with those obtained through the use of a Monte Carlo program

Comment on the contribution of S.C. Mo, N.A. Hanan and J.E. Matos: 'Comparison of the FRM-II HEU design with an alternative LEU design'

International Nuclear Information System (INIS)

Boening, K.

2004-01-01

The results of the reference paper, which came to our attention for the first time during this RERTR Meeting, are more or less consistent with neutronic data we have obtained earlier within the FRM-II project (i.e. with own calculations and extrapolations). However, a realistic comparison of the HEU design of the FR.M-II (HEU = highly enriched uranium, 93 % U-235) with an alternative LEU design (LEU = low enriched uranium, 20 % U-235) is only possible on the basis of identical assumptions on the input parameters and has to consider more than neutronic data only. Serious scientists and experts should not confuse the politicians with academic studies touching some aspects of the full story only. The comparison has shown that the performance and reliability of the FRM-II design, which uses HEU fuel, is so advantageous that it can not - not even approximately - be met by an alternative design using LEU fuel. A change of the FRM-II design from HEU to LEU fuel with the results as shown above - i.e. less performance, higher costs, more nuclear waste and higher risk potential, and all of this with a delay of at least 5 years this could never be justified. If a future development of more advanced fuels should allow us to achieve our scientific goals at the conditions as identified above also with uranium of reduced enrichment - there would be no objection to a corresponding later conversion. Activities to realize a new neutron source in Germany go back to the late 70's with the project of a new middle flux beam reactor (MSR), which was abandoned shortly later in favour of an ambitious new spallation neutron source (SNQ). After this project also having been terminated around 1985 because of too high costs and technological risks, the hopes of the German community of neutron scientists focussed on the FRM-II. If non-technical pressure would damage this project this would equally provide irreversible damage to the large and still prospering field of neutron research in Germany

DOE Lab-to-Lab MPC ampersand A workshop for cooperative tasks with Russian institutes: Focus on critical assemblies and item facilities

International Nuclear Information System (INIS)

Bieber, A.M. Jr.; Fishbone, L.G.; Kato, W.Y.; Lazareth, O.W.; Suda, S.C.; Garcia, D.; Haga, R.

1995-01-01

Seventeen Russian scientists and engineers representing five different institutes participated in a Workshop on material control and accounting as part of the US-Russian Lab-to-Lab Cooperative Program in Nuclear Materials Protection, Control, and Accounting (MPC ampersand A). In addition to presentations and discussions, the Workshop included an exercise at Brookhaven National Laboratory (BNL) and demonstrations at the Zero Power Physics Reactor (critical-assembly facility) of Argonne National Laboratory-West (ANL-W). The Workshop particularly emphasized procedures for physical inventory-taking at critical assemblies and item facilities, with associated supporting techniques and methods. By learning these topics and applying the methods and experience at their own institutes, the Russian scientists and engineers will be able to determine and verify nuclear material inventories based on sound procedures, including measurements. This will constitute a significant enhancement to MPC ampersand A at the Russian institutes

The Texts of the Instruments connected with the Agency's Assistance to Finland in Establishing a Sub-Critical Assemblies Project

International Nuclear Information System (INIS)

1964-01-01

The text of the Project Agreement between the Agency and the Government of Finland in connection with the Agency's assistance to that Government in establishing a sub-critical assemblies project is reproduced in Part I of this document for the information of all Members. This Agreement entered into force on 30 July 1963

The Texts of the Instruments connected with the Agency's Assistance to Finland in Establishing a Sub-Critical Assemblies Project

Energy Technology Data Exchange (ETDEWEB)

NONE

1964-02-10

The text of the Project Agreement between the Agency and the Government of Finland in connection with the Agency's assistance to that Government in establishing a sub-critical assemblies project is reproduced in Part I of this document for the information of all Members. This Agreement entered into force on 30 July 1963.

Summary of ORSphere critical and reactor physics measurements

Directory of Open Access Journals (Sweden)

Marshall Margaret A.

2017-01-01

Full Text Available In the early 1970s Dr. John T. Mihalczo (team leader, J.J. Lynn, and J.R. Taylor performed experiments at the Oak Ridge Critical Experiments Facility (ORCEF with highly enriched uranium (HEU metal (called Oak Ridge Alloy or ORALLOY to recreate GODIVA I results with greater accuracy than those performed at Los Alamos National Laboratory in the 1950s. The purpose of the Oak Ridge ORALLOY Sphere (ORSphere experiments was to estimate the unreflected and unmoderated critical mass of an idealized sphere of uranium metal corrected to a density, purity, and enrichment such that it could be compared with the GODIVA I experiments. This critical configuration has been evaluated. Preliminary results were presented at ND2013. Since then, the evaluation was finalized and judged to be an acceptable benchmark experiment for the International Criticality Safety Benchmark Experiment Project (ICSBEP. Additionally, reactor physics measurements were performed to determine surface button worths, central void worth, delayed neutron fraction, prompt neutron decay constant, fission density and neutron importance. These measurements have been evaluated and found to be acceptable experiments and are discussed in full detail in the International Handbook of Evaluated Reactor Physics Benchmark Experiments. The purpose of this paper is to summarize all the evaluated critical and reactor physics measurements evaluations.

Summary of ORSphere critical and reactor physics measurements

Science.gov (United States)

Marshall, Margaret A.; Bess, John D.

2017-09-01

In the early 1970s Dr. John T. Mihalczo (team leader), J.J. Lynn, and J.R. Taylor performed experiments at the Oak Ridge Critical Experiments Facility (ORCEF) with highly enriched uranium (HEU) metal (called Oak Ridge Alloy or ORALLOY) to recreate GODIVA I results with greater accuracy than those performed at Los Alamos National Laboratory in the 1950s. The purpose of the Oak Ridge ORALLOY Sphere (ORSphere) experiments was to estimate the unreflected and unmoderated critical mass of an idealized sphere of uranium metal corrected to a density, purity, and enrichment such that it could be compared with the GODIVA I experiments. This critical configuration has been evaluated. Preliminary results were presented at ND2013. Since then, the evaluation was finalized and judged to be an acceptable benchmark experiment for the International Criticality Safety Benchmark Experiment Project (ICSBEP). Additionally, reactor physics measurements were performed to determine surface button worths, central void worth, delayed neutron fraction, prompt neutron decay constant, fission density and neutron importance. These measurements have been evaluated and found to be acceptable experiments and are discussed in full detail in the International Handbook of Evaluated Reactor Physics Benchmark Experiments. The purpose of this paper is to summarize all the evaluated critical and reactor physics measurements evaluations.

IAEA Mission Sees High Commitment to Safety at Ghana's Research Reactor After HEU to LEU Fuel Conversion

International Nuclear Information System (INIS)

2018-01-01

An International Atomic Energy Agency (IAEA) team of experts said the operator of Ghana’s research reactor has demonstrated a high commitment to safety following the conversion of the reactor core to use low enriched uranium (LEU) as fuel instead of high enriched uranium (HEU). The team also made recommendations for further safety enhancements. The Integrated Safety Assessment for Research Reactors (INSARR) team concluded a five-day mission today to assess the safety of the GHARR-1 research reactor, originally commissioned in 1994. The 30 kW reactor, operated by the Ghana Atomic Energy Commission (GAEC) at the National Nuclear Research Institute in the capital Accra, is used primarily for trace element analysis for industrial or agricultural purposes, research, education and training. In 2017, the reactor core was converted in a joint effort by Ghana, the United States and China, with assistance from the IAEA. The IAEA supported the operation to eliminate proliferation risks associated with HEU, while maintaining important scientific research. The team made recommendations for improvements to the GAEC, including: • Completing the revision of reactor safety and operating documents to reflect the results of the commissioning of the reactor after the core fuel conversion. • Enhancing the training and qualification programme for operating personnel. • Improving the capability for monitoring operational safety parameters under all conditions. • Strengthening radiation protection by establishing an effective radiation monitoring of workplace. The GAEC said it will request a follow-up INSARR mission by 2020.

Pendulum support of the W7-X plasma vessel: Design, tests, manufacturing, assembly, critical aspects, status

Energy Technology Data Exchange (ETDEWEB)

Missal, B., E-mail: bernd.missal@ipp.mpg.de [Max-Planck-Institut für Plasmaphysik, EURATOM Association, Teilinstitut Greifswald, Wendelsteinstraße 1, D-17491 Greifswald (Germany); Leher, F.; Schiller, T. [MAN Diesel and Turbo SE, Werftstraße 17, 94469 Deggendorf (Germany); Friedrich, P. [Universität Rostock, FB Maschinenbau und Schiffstechnik, Albert-Einsteins-Straße 2, 18051 Rostock (Germany); Capriccioli, A. [ENEA Frascati, Fusion Technology Unit, Frascati (Italy)

2014-10-15

Highlights: • Plasma vessel support has to allow vertical adjustment and horizontal passive movement. • Planar sliding tables with PTFE do not fulfill all requirements. • Pendulums can fulfill all requirements. • Geometry and material of spherical bearings had to be optimized in calculations and tests. • Optimized pendulums were manufactured and assembled. - Abstract: The superconducting helical advanced stellarator Wendelstein 7-X (W7-X) is under construction at the Max-Planck-Institut für Plasmaphysik (IPP) in Greifswald, Germany. The three dimensional shape of plasma will be generated by 50 non-planar magnetic coils. The plasma vessel geometry follows exactly this three dimensional shape of plasma. To ensure the superconductivity of coils a cryo vacuum has to be generated. Therefore the coils and their support structure are enclosed within the outer vessel. Plasma vessel, coil structures and outer vessel have to be supported separately. This paper will describe the vertical supports of plasma vessel which have to fulfill two special requirements, vertical adjustability and horizontal mobility. These two tasks will be carried out by plasma vessel supports (PVS) with hydraulic cylinders, special sliding tables during assembly and pendulum supports during operating phase. The paper will give an overview of design, calculation, tests, fabrication, assembly, critical aspects and status of PVS.

Evaluation of nine popular de novo assemblers in microbial genome assembly.

Science.gov (United States)

Forouzan, Esmaeil; Maleki, Masoumeh Sadat Mousavi; Karkhane, Ali Asghar; Yakhchali, Bagher

2017-12-01

Next generation sequencing (NGS) technologies are revolutionizing biology, with Illumina being the most popular NGS platform. Short read assembly is a critical part of most genome studies using NGS. Hence, in this study, the performance of nine well-known assemblers was evaluated in the assembly of seven different microbial genomes. Effect of different read coverage and k-mer parameters on the quality of the assembly were also evaluated on both simulated and actual read datasets. Our results show that the performance of assemblers on real and simulated datasets could be significantly different, mainly because of coverage bias. According to outputs on actual read datasets, for all studied read coverages (of 7×, 25× and 100×), SPAdes and IDBA-UD clearly outperformed other assemblers based on NGA50 and accuracy metrics. Velvet is the most conservative assembler with the lowest NGA50 and error rate. Copyright © 2017. Published by Elsevier B.V.

Subcritical Neutron Multiplication Measurements of HEU Using Delayed Neutrons as the Driving Source

International Nuclear Information System (INIS)

Hollas, C.L.; Goulding, C.A.; Myers, W.L.

1999-01-01

A new method for the determination of the multiplication of highly enriched uranium systems is presented. The method uses delayed neutrons to drive the HEU system. These delayed neutrons are from fission events induced by a pulsed 14-MeV neutron source. Between pulses, neutrons are detected within a medium efficiency neutron detector using 3 He ionization tubes within polyethylene enclosures. The neutron detection times are recorded relative to the initiation of the 14-MeV neutron pulse, and subsequently analyzed with the Feynman reduced variance method to extract singles, doubles and triples neutron counting rates. Measurements have been made on a set of nested hollow spheres of 93% enriched uranium, with mass values from 3.86 kg to 21.48 kg. The singles, doubles and triples counting rates for each uranium system are compared to calculations from point kinetics models of neutron multiplicity to assign multiplication values. These multiplication values are compared to those from MC NP K-Code calculations

Nuclear Criticality Experimental Research Center (NCERC) Overview

Energy Technology Data Exchange (ETDEWEB)

Goda, Joetta Marie [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Grove, Travis Justin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hayes, David Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Myers, William L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Sanchez, Rene Gerardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-03-03

The mission of the National Criticality Experiments Research Center (NCERC) at the Device Assembly Facility (DAF) is to conduct experiments and training with critical assemblies and fissionable material at or near criticality in order to explore reactivity phenomena, and to operate the assemblies in the regions from subcritical through delayed critical. One critical assembly, Godiva-IV, is designed to operate above prompt critical. The Nuclear Criticality Experimental Research Center (NCERC) is our nation’s only general-purpose critical experiments facility and is only one of a few that remain operational throughout the world. This presentation discusses the history of NCERC, the general activities that makeup work at NCERC, and the various government programs and missions that NCERC supports. Recent activities at NCERC will be reviewed, with a focus on demonstrating how NCERC meets national security mission goals using engineering fundamentals. In particular, there will be a focus on engineering theory and design and applications of engineering fundamentals at NCERC. NCERC activities that relate to engineering education will also be examined.

Effects of existing evaluated nuclear data files on neutronics characteristics of the BFS-62-3A critical assembly benchmark model

International Nuclear Information System (INIS)

Semenov, Mikhail

2002-11-01

This report is continuation of studying of the experiments performed on BFS-62-3A critical assembly in Russia. The objective of work is definition of the cross section uncertainties on reactor neutronics parameters as applied to the hybrid core of the BN-600 reactor of Beloyarskaya NPP. Two-dimensional benchmark model of BFS-62-3A was created specially for these purposes and experimental values were reduced to it. Benchmark characteristics for this assembly are 1) criticality; 2) central fission rate ratios (spectral indices); and 3) fission rate distributions in stainless steel reflector. The effects of nuclear data libraries have been studied by comparing the results calculated using available modern data libraries - ENDF/B-V, ENDF/B-VI, ENDF/B-VI-PT, JENDL-3.2 and ABBN-93. All results were computed by Monte Carlo method with the continuous energy cross-sections. The checking of the cross sections of major isotopes on wide benchmark criticality collection was made. It was shown that ENDF/B-V data underestimate the criticality of fast reactor systems up to 2% Δk. As for the rest data, the difference between each other in criticality for BFS-62-3A is around 0.6% Δk. However, taking into account the results obtained for other fast reactor benchmarks (and steel-reflected also), it may conclude that the difference in criticality calculation results can achieve 1% Δk. This value is in a good agreement with cross section uncertainty evaluated for BN-600 hybrid core (±0.6% Δk). This work is related to the JNC-IPPE Collaboration on Experimental Investigation of Excess Weapons Grade Pu Disposition in BN-600 Reactor Using BFS-2 Facility. (author)

Comparison of the parameters of the IR-8 reactor with different fuel assembly designs with LEU fuel

International Nuclear Information System (INIS)

Vatulin, A.; Stetsky, Y.; Dobrikova, I.

1999-01-01

The estimation of neutron-physical, heat and hydraulic parameters of the IR-8 research reactor with low enriched uranium (LEU) fuel was performed. Two fuel assembly (FA) designs were reviewed: IRT-4M with the tubular type fuel elements and IRT-MR with the rod type fuel elements. UO 2 -Al dispersion 19.75% enrichment fuel is used in both cases. The results of the calculations were compared with main parameters of the reactor, using the current IRT-3M FA with 90% high enriched uranium (HEU) fuel. The results of these comparisons showed that during the LEU conversion of the reactor the cycle length, excess reactivity and peak power of the IRT-MR type FA are higher than for the IRT-3M type FA and IRT-4M type FA. (author)

Equilibrium polymerization models of re-entrant self-assembly

Science.gov (United States)

Dudowicz, Jacek; Douglas, Jack F.; Freed, Karl F.

2009-04-01

As is well known, liquid-liquid phase separation can occur either upon heating or cooling, corresponding to lower and upper critical solution phase boundaries, respectively. Likewise, self-assembly transitions from a monomeric state to an organized polymeric state can proceed either upon increasing or decreasing temperature, and the concentration dependent ordering temperature is correspondingly called the "floor" or "ceiling" temperature. Motivated by the fact that some phase separating systems exhibit closed loop phase boundaries with two critical points, the present paper analyzes self-assembly analogs of re-entrant phase separation, i.e., re-entrant self-assembly. In particular, re-entrant self-assembly transitions are demonstrated to arise in thermally activated equilibrium self-assembling systems, when thermal activation is more favorable than chain propagation, and in equilibrium self-assembly near an adsorbing boundary where strong competition exists between adsorption and self-assembly. Apparently, the competition between interactions or equilibria generally underlies re-entrant behavior in both liquid-liquid phase separation and self-assembly transitions.

Assembly, alignment and test of the Transiting Exoplanet Survey Satellite (TESS) optical assemblies

Science.gov (United States)

Balonek, Gregory; Brown, Joshua J.; Andre, James E.; Chesbrough, Christian D.; Chrisp, Michael P.; Dalpiaz, Michael; Lennon, Joseph; Richards, B. C.; Clark, Kristin E.

2017-08-01

The Transiting Exoplanet Survey Satellite (TESS) will carry four visible waveband, seven-element, refractive F/1.4 lenses, each with a 34 degree diagonal field of view. This paper describes the methods used for the assembly, alignment and test of the four flight optical assemblies. Prior to commencing the build of the four flight optical assemblies, a Risk Reduction Unit (RRU) was successfully assembled and tested [1]. The lessons learned from the RRU were applied to the build of the flight assemblies. The main modifications to the flight assemblies include the inking of the third lens element stray light mitigation, tighter alignment tolerances, and diamond turning for critical mechanical surfaces. Each of the optical assemblies was tested interferometrically and measured with a low coherence distance measuring interferometer (DMI) to predict the optimal shim thickness between the lens assembly and detector before -75°C environmental testing. In addition to individual test data, environmental test results from prior assemblies allow for the exploration of marginal performance differences between each of the optical assemblies.

The Prompt Fission Neutron Spectrum: From Experiment to the Evaluated Data and its Impact on Critical Assemblies

Energy Technology Data Exchange (ETDEWEB)

Rising, Michael Evan [Los Alamos National Laboratory

2015-06-10

After a brief introduction concerning nuclear data, prompt fission neutron spectrum (PFNS) evaluations and the limited PFNS covariance data in the ENDF/B-VII library, and the important fact that cross section uncertainties ~ PFNS uncertainties, the author presents background information on the PFNS (experimental data, theoretical models, data evaluation, uncertainty quantification) and discusses the impact on certain well-known critical assemblies with regard to integral quantities, sensitivity analysis, and uncertainty propagation. He sketches recent and ongoing research and concludes with some final thoughts.

Method for calculating the critical heat flux in mixed rod assemblies based on the tables of crisis in bundles

International Nuclear Information System (INIS)

Bobkov, V.P.

2000-01-01

The method for calculating the critical heat flux in the mixed rod assemblies, for example RBMK, containing three-four angle and peripheral macrocells, is presented. The method is based on generalization of experimental data in form of tables for the rods beams. It is recommended for the areas of parameters both provided for by experimental data and for others, where the data are absent. The advantages of the table method as follows: it is acceptable within a wide range of parameters and provides for smooth description of dependence of critical heat fluxes on these parameters; it is characterized by clearness, high reliability and accuracy and is easy in application [ru

HEU to LEU fuel conversion. Final report

International Nuclear Information System (INIS)

Mulder, R.U.

1994-10-01

The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG ampersand G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock ampersand Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B ampersand W) and the fuel designer (EG ampersand G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B ampersand W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology

HEU to LEU fuel conversion. Final report

Energy Technology Data Exchange (ETDEWEB)

Mulder, R.U.

1994-10-01

The Nuclear Regulatory Commission issued a ruling, effective March 27, 1986, that all U.S. non-power reactors convert from HEU fuel to LEU fuel. A Reduced Enrichment for Research and Test Reactors Program was conducted by the Department of Energy at Argonne National Laboratory to coordinate the development of the high density LEU fuel and assist in the development of Safety Analysis Reports for the smaller non-power reactors. Several meetings were held at Argonne in 1987 with the non-power reactor community to discuss the conversion and to set up a conversion schedule for university reactors. EG&G at Idaho was assigned the coordination of the fuel element redesigns. The fuel elements were manufactured by the Babcock & Wilcox Company in Lynchburg, Virginia. The University of Virginia was awarded a grant by the DOE Idaho Operations Office in 1988 to perform safety analysis studies for the LEU conversion for its 2 MW UVAR and 100 Watt CAVALIER reactors. The University subsequently decided to shut down the CAVALIER reactor. A preliminary SAR on the UVAR, along with Technical Specification changes, was submitted to the NRC in November, 1990. An updated SAR was approved by the NRC in January, 1991. In September, 1992, representatives from the fuel manufacturer (B&W) and the fuel designer (EG&G, Idaho) came to the UVAR facility to observe trial fittings of new 22 plate LEU mock fuel elements. B&W fabricated two non-fuel bearing elements, a regular 22 plate element and a control rod element. The elements were checked against the drawings and test fitted in the UVAR grid plate. The dimensions were acceptable and the elements fit in the grid plate with no problems. The staff made several suggestions for minor construction changes to the end pieces on the elements, which were incorporated into the final design of the actual fuel elements. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Sulfur activation at the Little Boy-Comet Critical Assembly: a replica of the Hiroshima bomb

International Nuclear Information System (INIS)

Kerr, G.D.; Emery, J.F.; Pace, J.V. III.

1985-04-01

Studies have been completed on the activation of sulfur by fast neutrons from the Little Boy-Comet Critical Assembly which replicates the general features of the Hiroshima bomb. The complex effects of the bomb's design and construction on leakage of sulfur-activation neutrons were investigated both experimentally and theoretically. Our sulfur activation studies were performed as part of a larger program to provide benchmark data for testing of methods used in recent source-term calculations for the Hiroshima bomb. Source neutrons capable of activating sulfur play an important role in determining neutron doses in Hiroshima at a kilometer or more from the point of explosion. 37 refs., 5 figs., 6 tabs

Summary of ORSphere Critical and Reactor Physics Measurements

Energy Technology Data Exchange (ETDEWEB)

Marshall, Margaret A.; Bess, John D.

2016-09-01

In the early 1970s Dr. John T. Mihalczo (team leader), J. J. Lynn, and J. R. Taylor performed experiments at the Oak Ridge Critical Experiments Facility (ORCEF) with highly enriched uranium (HEU) metal (called Oak Ridge Alloy or ORALLOY) to recreate GODIVA I results with greater accuracy than those performed at Los Alamos National Laboratory in the 1950s. The purpose of the Oak Ridge ORALLOY Sphere (ORSphere) experiments was to estimate the unreflected and unmoderated critical mass of an idealized sphere of uranium metal corrected to a density, purity, and enrichment such that it could be compared with the GODIVA I experiments. This critical configuration has been evaluated. Preliminary results were presented at ND2013. Since then, the evaluation was finalized and judged to be an acceptable benchmark experiment for the International Criticality Safety Benchmark Experiment Project (ICSBEP). Additionally, reactor physics measurements were performed to determine surface button worths, central void worth, delayed neutron fraction, prompt neutron decay constant, fission density and neutron importance. These measurements have been evaluated and found to be acceptable experiments and are discussed in full detail in the International Handbook of Evaluated Reactor Physics Benchmark Experiments. The purpose of this paper is summary summarize all the critical and reactor physics measurements evaluations and, when possible, to compare them to GODIVA experiment results.

Neutron spectra in two beam ports of a TRIGA Mark III reactor with HEU fuel

International Nuclear Information System (INIS)

Vega C, H. R.; Hernandez D, V. M.; Paredes G, L.; Aguilar, F.

2012-10-01

Before to change the HEU for Leu fuel of the ININ's TRIGA Mark III nuclear reactor the neutron spectra were measured in two beam ports using 5 and 10 W. Measurements were carried out in a tangential and a radial beam port using a Bonner sphere spectrometer. It was found that neutron spectra are different in the beam ports, in radial beam port the amplitude of thermal and fast neutrons are approximately the same while, in the tangential beam port thermal neutron peak is dominant. In the radial beam port the fluence-to-ambient dose equivalent factors are 131±11 and 124±10 p Sv-cm 2 for 5 and 10 W respectively while in the tangential beam port the fluence-to-ambient dose equivalent factor is 55±4 p Sv-cm 2 for 10 W. (Author)

Critical residues in the PMEL/Pmel17 N-terminus direct the hierarchical assembly of melanosomal fibrils

Science.gov (United States)

Leonhardt, Ralf M.; Vigneron, Nathalie; Hee, Jia Shee; Graham, Morven; Cresswell, Peter

2013-01-01

PMEL (also called Pmel17 or gp100) is a melanocyte/melanoma-specific glycoprotein that plays a critical role in melanosome development by forming a fibrillar amyloid matrix in the organelle for melanin deposition. Although ultimately not a component of mature fibrils, the PMEL N-terminal region (NTR) is essential for their formation. By mutational analysis we establish a high-resolution map of this domain in which sequence elements and functionally critical residues are assigned. We show that the NTR functions in cis to drive the aggregation of the downstream polycystic kidney disease (PKD) domain into a melanosomal core matrix. This is essential to promote in trans the stabilization and terminal proteolytic maturation of the repeat (RPT) domain–containing MαC units, precursors of the second fibrillogenic fragment. We conclude that during melanosome biogenesis the NTR controls the hierarchical assembly of melanosomal fibrils. PMID:23389629

Experimental investigation of critical velocity in a parallel plate research reactor fuel assembly

Energy Technology Data Exchange (ETDEWEB)

Castro, Alfredo J.A.; Scuro, Nikolas L.; Andrade, Delvonei A., E-mail: ajcastro@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNE-SP), Sao Paulo, SP (Brazil)

2017-07-01

The fuel elements of a MTR (Material Testing Reactor) type nuclear reactor are mostly composed of aluminum coated fuel plates containing the core of uranium silica (U{sub 3}Si{sub 2}) dispersed in an aluminum matrix. These plates have a thickness of the order of millimeters and are much longer in relation to their thickness. They are arranged in parallel in the assembly of the fuel element to form channels between them a few millimeters in thickness, through which there is a flow of the coolant. This configuration, combined with the need for a flow at high flow rates to ensure the cooling of the fuel element in operation, may create problems of mechanical failure of fuel plate due to the vibration induced by the flow in the channels. In the case of critical velocity excessive permanent deflections of the plates can cause blockage of the flow channel in the reactor core and lead to overheating in the plates. For this study an experimental bench capable of high volume flows and a test section that simulates a plate-like fuel element with three cooling channels were developed. The dimensions of the test section were based on the dimensions of the Fuel Element of the Brazilian Multipurpose Reactor (RMB), whose project is being coordinated by the National Commission of Nuclear Energy (CNEN). The experiments performed attained the objective of reaching Miller's critical velocity condition. The critical velocity was reached with 14.5 m/s leading to the consequent plastic deformation of the flow channel plates. (author)

The conversion of NRU from HEU to LEU fuel

International Nuclear Information System (INIS)

Sears, D.F.; Atfield, M.D.; Kennedy, I.C.

1990-01-01

The program at Chalk River Nuclear Laboratories (CRNL) to develop and test low-enriched uranium fuel (LEU, 3 Si, USiAl, USi Al and U 3 Si 2 (U-3.96 wt% Si; U-3.5 wt% Si-1.5 wt% AL; U-3.2 wt%; Si-3 wt% Al; U-7.3 wt% Si, respectively). Fuel elements were fabricated with uranium loadings suitable for NRU, 3.15 gU/cm 3 , and for NRX, 4.5 gU/cm 3 , and were irradiated under normal fuel-operating conditions. Eight experimental irradiations involving 100 mini-elements and 84 full-length elements (7X12-element rods) were completed to qualify the LEU fuel and the fabrication technology. Post irradiation examinations confirmed that the performance of the LEU fuel, and that of a medium enrichment uranium (MEU, 45% U-235) alloy fuel tested as a back-up, was comparable to the HEU fuel. The uranium silicide dispersion fuel swelling was approximately linear up to burnups exceeding NRU's design terminal burnup (80 at%). NRU was partially converted to LEU fuel when the first 31 prototype fuel rods manufactured with industrial scale production equipment were installed in the reactor. The rods were loaded in NRU at a fuelling rate of about two rods per week over the period 1988 September to December. This partial LEU core (one third of a full NRU core) has allowed the reactor engineers and physicists to evaluate the bulk effects of the LEU conversion on NRU operations. As expected, the irradiation is proceeding without incident

Long Range Active Detection of HEU Based on Thermal Neutron Multiplication

Energy Technology Data Exchange (ETDEWEB)

Forman L.; Dioszegi I.; Salwen, C.; and Vanier, P.E.

2010-05-24

We report on the results of measurements of proton irradiation on a series of targets at Brookhaven National Laboratory’s (BNL) Alternate Gradient Synchrotron Facility (AGS), in collaboration with LANL and SNL. We examined the prompt radiation environment in the tunnel for the DTRA-sponsored series (E 972), which investigated the penetration of air and subsequent target interaction of 4 GeV proton pulses. Measurements were made by means of an organic scintillator with a 500 MHz bandwidth system. We found that irradiation of a depleted uranium (DU) target resulted in a large gamma-ray signal in the 100-500 µsec time region after the proton flash when the DU was surrounded by polyethylene, but little signal was generated if it was surrounded by boron-loaded polyethylene. Subsequent Monte Carlo (MCNPX) calculations indicated that the source of the signal was consistent with thermal neutron capture in DU. The MCNPX calculations also indicated that if one were to perform the same experiment with a highly enriched uranium (HEU) target there would be a distinctive fast neutron yield in this 100-500 µsec time region from thermal neutron-induced fission. The fast neutrons can be recorded by the same direct current system and differentiated from gamma ray pulses in organic scintillator by pulse shape discrimination.

Commissioning and start-up of RA-8 critical assembly

International Nuclear Information System (INIS)

Lorenzo, N. de; Diaz, C.; Facchini, G.; Fernandez, C.; Fittipaldi, A.; Juracich, R.; Levanon, I.; Manceda, J.; Martinez, J.; Mogdan, R.; Perez, J.; Scarnichia, E.; Blaumann, H.; Gennuso, G.; Scotti, G.

1999-01-01

The RA-8 critical assembly was designed as one of the experimental facilities for the CAREM Reactor Project. This paper describes the activities developed during the cold and hot commissioning, pointing out the difficulties and the solutions applied (some of them original ones). Moreover, this paper will show the main features of the newest nuclear installation of CNEA making a brief description of its characteristics. Among the special circumstances related to the commissioning that are described in the paper we can mention the following: 1. The facility shares the building with the Thermohydraulic Assay Laboratory (L.E.T.), another experimental facility of CAREM, and thus some shared systems have already been working for many years before this start up. Special procedures for these systems were designed to verify the proper functioning under the new requirements. 2. A new driving mechanism, based in hydraulic cylinders, was used to move the control rods. The criteria for acceptance and a validation of the procedure completeness have been carried out. 3. The implementation of a power measurement system based in neutron noise. 4. Measurement of Power Distribution using direct gamma counting from the fuel elements. 5. The commissioning was interrupted for a ten-month period because the personnel involved had to carry out the commissioning of the Egyptian Research Reactor 2. Also, the common activities during a commissioning are described, pointing out the major steps carried out and the results obtained. The following are examples of these activities: 1. Environmental dose survey (before fuel loading and during other stages). 2. Test of equipment and systems isolated from the rest of the plant. 3. Integrated system test (two or more systems working at the same time). 4. Start-up and power operation simulations before fuel loading. 5. Fuel loading strategy during the approximation to criticality by mass. 6. Modification of systems' components to improve the

MCNP and OMEGA criticality calculations

International Nuclear Information System (INIS)

Seifert, E.

1998-04-01

The reliability of OMEGA criticality calculations is shown by a comparison with calculations by the validated and widely used Monte Carlo code MCNP. The criticality of 16 assemblies with uranium as fissionable is calculated with the codes MCNP (Version 4A, ENDF/B-V cross sections), MCNP (Version 4B, ENDF/B-VI cross sections), and OMEGA. Identical calculation models are used for the three codes. The results are compared mutually and with the experimental criticality of the assemblies. (orig.)

Technical investigation of a pyrophoric event involving corrosion products from HEU ZPPR fuel plates

International Nuclear Information System (INIS)

Totemeier, T. C.

2000-01-01

A pyrophoric event recently occurred which involved corrosion products collected from highly-enriched uranium (HEU) fuel plates used in the Zero Power Physics Reactor (ZPPR). This paper summarizes the event and its background, and presents the results of an investigation into its source and mechanism. The investigation focused on characterization of corrosion product samples similar to those involved in the event using thermo-gravimetric analysis (TGA). Burning curve TGA tests were performed to measure the ignition temperature and hydride fractions of corrosion products in several different conditions to assess the effects of passivation treatment and long-term storage on chemical reactivity. The hydride fraction and ignition temperature of the corrosion products were found to be strongly dependent on the corrosion extent of the source metal. The results indicate that the energy source for the event was a considerable quantity of uranium hydride present in the corrosion products, but the specific ignition mechanism could not be identified

Structural characteristics of a graphite moderated critical assembly for a Zero Power reactor at IEA (Brazil)

International Nuclear Information System (INIS)

Almeida Ferreira, A.C. de; Hukai, R.Y.

1975-01-01

The structural characteristics of a graphite moderated core of a critical assembly to be installed in the Zero Power Reactor of IEA have been defined. These characteristics are the graphite block dimensions, the number and dimensions of the holes in the graphite, the pitch, the dimensions of the sticks of fuel and graphite to be inserted in the holes, and the mechanical reproducibility of the system. The composition of the fuel and moderator sticks were also defined. The main boundary conditions were the range of the relation C/U and C/TH used in commercial HTGR and the neutronics homogeneity

The Texts of the Instruments connected with the Agency's Assistance to Mexico in Establishing a Sub-Critical Assembly Project

Energy Technology Data Exchange (ETDEWEB)

NONE

1967-10-25

The texts of the Supply Agreement between the Agency and the Governments of Mexico and the United States of America, and of the Project Agreement between the Agency and the Government of Mexico, connected with the Agency's assistance to the latter Government in establishing a sub-critical assembly project, are reproduced in this document for the information of all Members. Both Agreements entered into force on 23 August 1967.

The Texts of the Instruments connected with the Agency's Assistance to Mexico in Establishing a Sub-Critical Assembly Project

Energy Technology Data Exchange (ETDEWEB)

NONE

1966-07-07

The texts of the Supply Agreement between the Agency and the Governments of Mexico and the United States of America, and of the Project Agreement between the Agency and the Government of Mexico in connection with the Agency's assistance to that Government in establishing a sub-critical assembly project.. are reproduced in this document for the information of all Members. Both Agreements entered into force on 20 June 1966.

The Texts of the Instruments connected with the Agency's Assistance to Mexico in Establishing a Sub-Critical Assembly Project

International Nuclear Information System (INIS)

1966-01-01

The texts of the Supply Agreement between the Agency and the Governments of Mexico and the United States of America, and of the Project Agreement between the Agency and the Government of Mexico in connection with the Agency's assistance to that Government in establishing a sub-critical assembly project.. are reproduced in this document for the information of all Members. Both Agreements entered into force on 20 June 1966

The Texts of the Instruments connected with the Agency's Assistance to Mexico in Establishing a Sub-Critical Assembly Project

International Nuclear Information System (INIS)

1967-01-01

The texts of the Supply Agreement between the Agency and the Governments of Mexico and the United States of America, and of the Project Agreement between the Agency and the Government of Mexico, connected with the Agency's assistance to the latter Government in establishing a sub-critical assembly project, are reproduced in this document for the information of all Members. Both Agreements entered into force on 23 August 1967

Study of neutron noise from reflected, metal assemblies with criticality safety applications in mind

International Nuclear Information System (INIS)

Barnett, C.S.

1985-01-01

The author studied the statistics of detected neutrons that leaked from four subcritical reflected, enriched-uranium assemblies, to explore the feasibility of developing a criticality warning system based on neutron noise analysis. The calculated multiplication factors of the assemblies are 0.59, 0.74, 0.82, and 0.92. The author studied three possible discriminators, i.e., three signatures that might be used to discriminate among assemblies of various multiplications. They are (1) variance-to-mean ratio of the counts in a time bin (V/M), (2) covariance-to-mean ratio of the counts in a common time bin from two different detectors (C/M), (3) covariance-to-mean ratio of the counts from a single detector in two adjacent time bins of equal length, which the author calls the serial-covariance-to-mean ratio (SC/M). The performances of the three discriminators were not greatly different, but a hierarchy did emerge: SC/M greater than or equal to V/M greater than or equal to C/M. An example of some results: in the neighborhood of k = 0.6 the Δk required for satisfactory discrimination varies from about 3% to 7% as detector solid angle varies from 19% to 5%. In the neighborhood of k = 0.8 the corresponding Δks are 1% and 2%. The noise analysis techniques studied performed well enough in deeply subcritical situations to deserve testing in an applications environment. They have a good chance of detecting changes in reactivity that are potentially dangerous. One can expect sharpest results when doing comparison, i.e., when comparing two records, one taken in the past under circumstances known to be normal and one taken now to search for change

Study of neutron noise from reflected, metal assemblies with criticality safety applications in mind

International Nuclear Information System (INIS)

Barnett, C.S.

1985-01-01

The author studied the statistics of detected neutrons that leaked from four subcritical reflected, enriched-uranium assemblies, to explore the feasibility of developing a criticality warning system based on neutron noise analysis. The calculated multiplication factors of the assemblies are 0.59, 0.74, 0.82, and 0.92. The author studied three possible discriminators, i.e., three signatures that might be used to discriminate among assemblies of various multiplications. They are: (1) variance-to-mean ratio of the counts in a time bin (V/M); (2) covariance-to-mean ratio of the counts in a common time bin from two different detectors (C/M); and (3) covariance-to-mean ratio of the counts from a single detector in two adjacent time bins of equal length, which the author calls the serial-covariance-to-mean ratio (SC/M). The performances of the three discriminators were not greatly different, but a hierarchy did emerge: SC/M greater than or equal to V/M greater than or equal to C/M. An example of some results: in the neighborhood of k = 0.6 the Δk required for satisfactory discrimination varies from about 3% to 7% as detector solid angle varies from 19% to 5%. In the neighborhood of k = 0.8 the corresponding Δks are 1% and 2%. The noise analysis techniques studied performed well enough in deeply subcritical situations to deserve testing in an applications environment. They have a good chance of detecting changes in reactivity that are potentially dangerous. One can expect sharpest results when doing comparisons, i.e., when comparing two records, one taken in the past under circumstances known to be normal and one taken now to search for change

Experimental performance and results of the critical pebble bed facility KAHTER

Energy Technology Data Exchange (ETDEWEB)

Krings, F. J.; Drueke, V.; Kirch, N.; Neef, R. D.

1974-10-15

The paper provides a description and results of critical experiments performed in KAHTER fueled with pebbles containing coated particles of HEU/Th oxide with a ratio of uranium-to-thorium of 1.1:5. Core loadings with varying amounts of fuel and solid graphite pebbles were tested with fuel-to-graphite pebble ratios of 3:1, 1:1, and 1:3. Tests included criticality for various fuel loadings with all control rods removed, control rod worths for reflector-mounted control as single rods and in a bank and control worths for a central control rod, reaction rates by flux wire activations (Dy, Mn, In, Au, and U-235) and detector measurements (BF3 and fission chamber), simulated xenon stability testing using the motions of a Cf-252 source and Cd-absorber observed by an externally-located BF3 detector, and the reactivity worth of a Hf burnable absorber. For calculations of the room-temperature zero-power critical experiment, the values for nitrogen and hydrogen contents of the graphite were taken from previous experiments in CESAR.

Implementing New Methods of Laser Marking of Items in the Nuclear Material Control and Accountability System at SSC RF-IPPE: An Automated Laser Marking System

International Nuclear Information System (INIS)

Regoushevsky, V.I.; Tambovtsev, S.D.; Dvukhsherstnov, V.G.; Efimenko, V.F.; Ilyantsev, A.I.; Russ, G.P. III

2009-01-01

For over ten years SSC RF-IPPE, together with the US DOE National Laboratories, has been working on implementing automated control and accountability methods for nuclear materials and other items. Initial efforts to use adhesive bar codes or ones printed (painted) onto metal revealed that these methods were inconvenient and lacked durability under operational conditions. For NM disk applications in critical stands, there is the additional requirement that labels not affect the neutron characteristics of the critical assembly. This is particularly true for the many stainless-steel clad disks containing highly enriched uranium (HEU) and plutonium that are used at SSC RF-IPPE for modeling nuclear power reactors. In search of an alternate method for labeling these disks, we tested several technological options, including laser marking and two-dimensional codes. As a result, the method of laser coloring was chosen in combination with Data Matrix ECC200 symbology. To implement laser marking procedures for the HEU disks and meet all the nuclear material (NM) handling standards and rules, IPPE staff, with U.S. technical and financial support, implemented an automated laser marking system; there are also specially developed procedures for NM movements during laser marking. For the laser marking station, a Zenith 10F system by Telesis Technologies (10 watt Ytterbium Fiber Laser and Merlin software) is used. The presentation includes a flowchart for the automated system and a list of specially developed procedures with comments. Among other things, approaches are discussed for human-factor considerations. To date, markings have been applied to numerous steel-clad HEU disks, and the work continues. In the future this method is expected to be applied to other MC and A items.

A neutronic feasibility study for LEU conversion of the SAFARI-1 reactor

International Nuclear Information System (INIS)

Pond, R.B.; Hanan, N.A.; Matos, J.E.; Ball, G.

2000-01-01

A neutronic feasibility study to convert the SAFARI-1 reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with NECSA. Comparisons were made of the reactor performance with the current 90% enriched HEU fuel type (UAl) and two 19.75% enriched LEU fuel types (U 3 Si 2 and U7Mo). The thermal fluxes with the LEU fuels were 3 - 9% lower than with the current HEU fuel. For the same fuel assembly design, a uranium density of approximately 4.5 g/cm 3 was required with U 3 Si 2 -Al fuel and a uranium density of about 4.6 g/cm 3 was required with U7Mo-Al fuel to match the 24.6-day cycle of the UAl-alloy fuel with 0.92 gU/cm 3 . The selection of a suitable LEU fuel and the decision to convert SAFARI-1 will be an economic matter that depends upon the fuel type, fuel assembly design, experiment performance and fuel cycle costs. (author)

Modélisation et automatisation des procédés d’écriture et de production de supports de formation numérisés - Le modèle M.A.Ï.HEU.T.I.C. de la CCI de Paris

Directory of Open Access Journals (Sweden)

José Martin

2005-01-01

Full Text Available Cet article expose les conclusions d’un projet de recherche de la Direction de l’Enseignement de la Chambre de Commerce et d’Industrie de Paris (CCIP, mené de 2003 à 2005, dont l’aboutissement est un modèle didactique de production de contenus de cours numérisés, baptisé M.A.Ï.HEU.T.I.C.[[ M.A.Ï.HEU.T.I.C. : Modèle Appliqué d’Interprétation Heuristique des Technologies de l’Information et de la Communication.

Unattended Monitoring of HEU Production in Gaseous Centrifuge Enrichment Plants using Automated Aerosol Collection and Laser-based Enrichment Assay

International Nuclear Information System (INIS)

Anheier, Norman C.; Bushaw, Bruce A.

2010-01-01

Nuclear power is enjoying rapid growth as government energy policies and public demand shift toward low carbon energy production. Pivotal to the global nuclear power renaissance is the development and deployment of robust safeguards instrumentation that allows the limited resources of the IAEA to keep pace with the expansion of the nuclear fuel cycle. Undeclared production of highly enriched uranium (HEU) remains a primary proliferation concern for modern gaseous centrifuge enrichment plants (GCEPs), due to their massive separative work unit (SWU) processing power and comparably short cascade equilibrium timescale. The Pacific Northwest National Laboratory is developing an unattended safeguards instrument, combining continuous aerosol particulate collection with uranium isotope assay, to provide timely detection of HEU production within a GCEP. This approach is based on laser vaporization of aerosol particulates, followed by laser spectroscopy to characterize the uranium enrichment level. Our prior investigation demonstrated single-shot detection sensitivity approaching the femtogram range and relative isotope ratio uncertainty better than 10% using gadolinium as a surrogate for uranium. In this paper we present measurement results on standard samples containing traces of depleted, natural, and low enriched uranium, as well as measurements on aerodynamic size uranium particles mixed in background materials (e.g., dust, minerals, soils). Improvements and optimizations in the detection electronics, signal timing, calibration, and laser alignment have lead to significant improvements in detection sensitivity and enrichment accuracy, contributing to an overall reduction in the false alarm probability. The sample substrate media was also found to play a significant role in facilitating laser-induced vaporization and the production of energetic plasma conditions, resulting in ablation optimization and further improvements in the isotope abundance sensitivity.

Analysis of measurements for a uranium-free core experiment at the BFS-2 critical assembly

Energy Technology Data Exchange (ETDEWEB)

Hunter, Stuart [Japan Nuclear Cycle Development Inst., Oarai, Ibaraki (Japan). Oarai Engineering Center

1999-04-01

This document describes a series of calculations that were carried out to model various measurements from the BFS-58-1-I1 experiment. BFS-58-1-I1 was a mock-up of a uranium-free, Pu burning core at BFS-2, a Russian critical assembly operated by IPPE. The experiment measured values of Keff, Na void reactivity worth, material sample reactivity worths and reaction rate ratios. The experiments were modelled using a number of different methods. Basic nuclear data was taken from JENDL-3.2, in either 70 or 18 groups. Cross-section data for the various material regions of the assembly were calculated by either SLAROM or CASUP; the heterogeneous structure of the core regions was modelled in these calculations, with 3 different options considered for representing the (essentially 2D) geometry of the assembly components in a 1D cell model. Whole reactor calculations of flux and Keff were done using both a diffusion model (CITATION) and a transport model (TWOTRAN2), both using an RZ geometry. Reactivity worths were calculated both directly from differences in Keff values and by using the exact perturbation calculations of PERKY and SN-PERT (for CITATION and TWOTRAN2, respectively). Initial calculations included a number of inaccuracies in the assembly representation, a result of communication difficulties between JNC and IPPE; these errors were removed for the final calculations that are presented. Calculations for the experiments have also been carried out in Russia (IPPE) and France (CEA) as part of an international comparison exercise, some of those results are also presented here. The calculated value of Keff was 1.1%{delta}k/k higher than the measured value, Na void worth C/E values were {approx}1.06; these results were considered to be reasonable. (Discrepancies in certain Na void values were probably due to experimental causes , though the effect should be investigated in any future experiments.) Several sample worth values were small compared with calculational

SOURCE OF BURNUP VALUES FOR COMMERCIAL SPENT NUCLEAR FUEL ASSEMBLIES

International Nuclear Information System (INIS)

BSC

2004-01-01

Waste packages are loaded with commercial spent nuclear fuel (SNF) that satisfies the minimum burnup requirements of a criticality loading curve. The burnup value assigned by the originating nuclear utility to each SNF assembly (assigned burnup) is used to load waste packages in compliance with a criticality loading curve. The burnup provided by a nuclear utility has uncertainties, so conservative calculation methods are used to characterize those uncertainties for incorporation into the criticality loading curves. Procedural safety controls ensure that the correct assembly is loaded into each waste package to prevent a misload that could create a condition affecting the safety margins. Probabilistic analyses show that procedural safety controls can minimize the chance of a misload but can not completely eliminate the possibility. Physical measurements of burnup with instrumentation in the surface facility are not necessary due to the conservative calculation methods used to produce the criticality loading curves. The reactor records assigned burnup of a commercial SNF assembly contains about two percent uncertainty, which is increased to five-percent to ensure conservatism. This five-percent uncertainty is accommodated by adjusting the criticality loading curve. Also, the record keeping methods of nuclear utilities are not uniform and the level of detail required by the NRC has varied over the last several decades. Thus, some SNF assemblies may have assigned burnups that are averages for a batch of assemblies with similar characteristics. Utilities typically have access to more detailed core-follow records that allow the batch average burnup to be changed to an assembly specific burnup. Alternatively, an additional safety margin is incorporated into the criticality loading curve to accommodate SNF assemblies with batch average burnups or greater uncertainties due to the methodology used by the nuclear utility. The utility records provide the assembly identifier

Neutronic analysis of HEU to LEU conversion calculation for AEOI 5 MW pool-type MTR fuel research reactor core

International Nuclear Information System (INIS)

Pazirandeh, A.; Lutz, D.; Bartsch, G.

1987-07-01

The possibility of converting HEU(93%) fuel to LEU(20%) fuel without or with slight alteration to the fuel element geometry is discussed. The fuel density varies between 1.7 to 4.1 g U-235/cm. In cross section generation a unit cell with an extra zone to account for extra Al and water was considered. In burnup calculations a sequential shuffling pattern was assumed with fixed position control fuel elements. A cross section data set in 45 energy groups were generated using RSYST/CGM system using the cross section library JFET. Then for 2D-diffusion calculations homogenized and condensed 5 energy group cross sections were prepared. (orig./HP)

History of critical experiments at Pajarito Site

International Nuclear Information System (INIS)

Paxton, H.C.

1983-03-01

This account describes critical and subcritical assemblies operated remotely at the Pajarito Canyon Site at the Los Alamos National Laboratory. Earliest assemblies, directed exclusively toward the nuclear weapons program, were for safety tests. Other weapon-related assemblies provided neutronic information to check detailed weapon calculations. Topsy, the first of these critical assemblies, was followed by Lady Godiva, Jezebel, Flattop, and ultimately Big Ten. As reactor programs came to Los Alamos, design studies and mockups were tested at Pajarito Site. For example, nearly all 16 Rover reactors intended for Nevada tests were preceded by zero-power mockups and proof tests at Pajarito Site. Expanded interest and capability led to fast-pulse assemblies, culminating in Godiva IV and Skua, and to the Kinglet and Sheba solution assemblies

History of critical experiments at Pajarito Site

Energy Technology Data Exchange (ETDEWEB)

Paxton, H.C.

1983-03-01

This account describes critical and subcritical assemblies operated remotely at the Pajarito Canyon Site at the Los Alamos National Laboratory. Earliest assemblies, directed exclusively toward the nuclear weapons program, were for safety tests. Other weapon-related assemblies provided neutronic information to check detailed weapon calculations. Topsy, the first of these critical assemblies, was followed by Lady Godiva, Jezebel, Flattop, and ultimately Big Ten. As reactor programs came to Los Alamos, design studies and mockups were tested at Pajarito Site. For example, nearly all 16 Rover reactors intended for Nevada tests were preceded by zero-power mockups and proof tests at Pajarito Site. Expanded interest and capability led to fast-pulse assemblies, culminating in Godiva IV and Skua, and to the Kinglet and Sheba solution assemblies.

Investigation of the neutron detection statistics in fast critical assembly BFS-24-1

International Nuclear Information System (INIS)

Avramov, A.M.; Tyutyunnikov, P.L.; Mikulski, A.T.; Rafalska, E.; Chwaszczewski, S.; Jablonski, K.

1974-01-01

The results of the neutron detection statistics investigation at the fast critical assembly BFS-24-1 are given. The Ross-α measurements were carried out using: digital flash-start unit and 256 channel time analyzer, 10 channel time analyzer, alphameter device. Parallely the measurements using the variable dead time method and zero probability method were performed. The prompt neutron decay constants, the effectiveness of neutron detector and the intensity of external neutron source are determined using the experimental data. The experimental values of prompt neutron decay constant are compared with the calculated ones. The codes used in the calculation are following: one dimensional, diffusion, 26-group code 26-M and EWA-1, one dimensional, multiregion, nonstationary diffusion 3-group code SPECTR, 26-group, diffusion code in buckling approximation, MIXSPECTR. In all codes the 26 group nuclear constants BNAB-26 and BNAB-70 are used. (author)

Critical experiments with mixed oxide fuel

International Nuclear Information System (INIS)

Harris, D.R.

1997-01-01

This paper very briefly outlines technical considerations in performing critical experiments on weapons-grade plutonium mixed oxide fuel assemblies. The experiments proposed would use weapons-grade plutonium and Er 2 O 3 at various dissolved boron levels, and for specific fuel assemblies such as the ABBCE fuel assembly with five large water holes. Technical considerations described include the core, the measurements, safety, security, radiological matters, and licensing. It is concluded that the experiments are feasible at the Rensselaer Polytechnic Institute Reactor Critical Facility. 9 refs

Fuel Management at the Dalat Nuclear Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Pham, V.L.; Nguyen, N.D.; Luong, B.V.; Le, V.V.; Huynh, T.N.; Nguyen, K.C. [Nuclear Research Institute, 01 Nguyen Tu Luc Street, Dalat City (Viet Nam)

2011-07-01

The Dalat Nuclear Research Reactor (DNRR) is a pool type research reactor which was reconstructed in 1982 from the old 250 kW TRIGA-MARK II reactor. The spent fuel storage was newly designed and installed in the place of the old thermalizing column for biological irradiation. The core was loaded by Russian WWR-M2 fuel assemblies (FAs) with 36% enrichment. The reconstructed reactor reached its initial criticality in November 1983 and attained it nominal power of 500 kW in February 1984. The first fuel reloading was executed in April 1994 after more than 10 years of operation with 89 highly enriched uranium (HEU) FAs. The third fuel reloading by shuffling of HEU FAs was executed in June 2004. After the shuffling the working configuration of reactor core kept unchanged of 104 HEU FAs. The fourth fuel reloading was executed in November 2006. The 2 new HEU FAs were loaded in the core periphery, at previous locations of wet irradiation channel and dry irradiation channel. After reloading the working configuration of reactor core consisted of 106 HEU FAs. Contracts for reactor core conversion between USA, Russia, Vietnam and the International Atomic Energy Agency for Nuclear fuel manufacture and supply for DNRR and Return of Russian-origin non-irradiated highly enriched uranium fuel to the Russian Federation have been realized in 2007. According to the results of design and safety analyses performed by the joint study between RERTR Program at Argonne National Laboratory and Vietnam Atomic Energy Institute the mixed core configurations of irradiated HEU and new low enriched uranium (LEU) FAs has been created on 12 September, 2007 and on 20 July, 2009. After reloading in 2009, the 14 HEU FAs with highest burnup were removed from the core and put in the interim storage in reactor pool. The works on full core conversion for the DNRR are being realized in cooperation with the organizations, DOE and IAEA. Contract for Nuclear fuel manufacture and supply of 66 LEU FAs for DNRR

Rapid centriole assembly in Naegleria reveals conserved roles for both de novo and mentored assembly.

Science.gov (United States)

Fritz-Laylin, Lillian K; Levy, Yaron Y; Levitan, Edward; Chen, Sean; Cande, W Zacheus; Lai, Elaine Y; Fulton, Chandler

2016-03-01

Centrioles are eukaryotic organelles whose number and position are critical for cilia formation and mitosis. Many cell types assemble new centrioles next to existing ones ("templated" or mentored assembly). Under certain conditions, centrioles also form without pre-existing centrioles (de novo). The synchronous differentiation of Naegleria amoebae to flagellates represents a unique opportunity to study centriole assembly, as nearly 100% of the population transitions from having no centrioles to having two within minutes. Here, we find that Naegleria forms its first centriole de novo, immediately followed by mentored assembly of the second. We also find both de novo and mentored assembly distributed among all major eukaryote lineages. We therefore propose that both modes are ancestral and have been conserved because they serve complementary roles, with de novo assembly as the default when no pre-existing centriole is available, and mentored assembly allowing precise regulation of number, timing, and location of centriole assembly. © 2016 Wiley Periodicals, Inc.

Burn-up measurements of spent fuel using gamma spectrometry technique

International Nuclear Information System (INIS)

Pereda, C.; Henriquez, C.; Klein, J.; Medel, J.

2005-01-01

Burn-up results obtained for HEU (45% of 235 U) fuel assemblies of the RECH-1 Research Reactor using gamma spectrometry technique are presented. The spectra were got from an in-pool facility built in the reactor to be mainly used to measure the burnup of irradiated fuel assemblies with short cooling time, where 95 Zr is being evaluated as possible fission monitor. A program to measure all spent fuel assemblies of the RECH-1 reactor was initiated in the frame of the Regional Project RLA/4/018: 'Management of Spent Fuel from Research Reactors'. The results presented here were obtained from HEU spent fuel assemblies with cooling time greater than 100 days and 137 Cs was used as fission monitor. The efficiency of the in-pool system was determined using a slightly burnt experimental fuel assembly, which has one fuel plate (one of the outer plates) and the rest are dummy plates. An average burn-up of 2.8% of 235 U was previously measured for the experimental fuel assembly utilizing a facility installed in a hot cell and 137 Cs was used as monitor. (author)

Safety analysis report for packaging, Oak Ridge Y-12 Plant, model DC-1 package with HEU oxide contents. Change pages for Rev.1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-01-18

This Safety Analysis Report for Packaging for the Oak Ridge Y-12 Plant for the Model DC-1 package with highly enriched uranium (HEU) oxide contents has been prepared in accordance with governing regulations form the Nuclear Regulatory Commission and the Department of Transportation and orders from the Department of energy. The fundamental safety requirements addressed by these regulations and orders pertain to the containment of radioactive material, radiation shielding, and nuclear subcriticality. This report demonstrates how these requirements are met.

Safety analysis report for packaging, Oak Ridge Y-12 Plant, model DC-1 package with HEU oxide contents. Change pages for Rev.1

International Nuclear Information System (INIS)

1995-01-01

This Safety Analysis Report for Packaging for the Oak Ridge Y-12 Plant for the Model DC-1 package with highly enriched uranium (HEU) oxide contents has been prepared in accordance with governing regulations form the Nuclear Regulatory Commission and the Department of Transportation and orders from the Department of energy. The fundamental safety requirements addressed by these regulations and orders pertain to the containment of radioactive material, radiation shielding, and nuclear subcriticality. This report demonstrates how these requirements are met

Criticality safety

International Nuclear Information System (INIS)

Walker, G.

1983-01-01

When a sufficient quantity of fissile material is brought together a self-sustaining neutron chain reaction will be started in it and will continue until some change occurs in the fissile material to stop the chain reaction. The quantity of fissile material required is the 'Critical Mass'. This is not a fixed quantity even for a given type of fissile material but varies between quite wide limits depending on a number of factors. In a nuclear reactor the critical mass of fissile material is assembled under well-defined condition to produce a controllable chain reaction. The same materials have to be handled outside the reactor in all stages of fuel element manufacture, storage, transport and irradiated fuel reprocessing. At any stage it is possible (at least in principle) to assemble a critical mass and thus initiate an accidental and uncontrollable chain reaction. Avoiding this is what criticality safety is all about. A system is just critical when the rate of production of neutrons balances the rate of loss either by escape or by absorption. The factors affecting criticality are, therefore, those which effect neutron production and loss. The principal ones are:- type of nuclide and enrichment (or isotopic composition), moderation, reflection, concentration (density), shape and interaction. Each factor is considered in detail. (author)

The effect of grid assembly mixing vanes on critical heat flux values and azimuthal location in fuel assemblies

International Nuclear Information System (INIS)

De Crecy, F.

1994-01-01

Critical heat flux (CHF) is one of the limiting phenomena for a PWR. It has been widely studied for years, but many facts are still not satisfactorily understood. This paper deals with the effect of the grid assembly mixing vanes on both the value of the CHF and the azimuthal location of the departure from nucleate boiling (DNB). A series of experimental studies was performed on electrically heated, 5x5 square pitched, vertical rod bundles. Two specific grid assembly designs were used: with and without mixing vanes. DNB was detected by eight thermocouples welded internally in each rod at the same level in order to determine the azimuthal location. The coolant was Freon-12 flowing upwards to simulate high pressure water (as defined by Stevens). Single-phase flow experiments were also conducted to measure the exit temperature field in order to obtain the mixing coefficients for subchannel analysis.The results show very clearly that the mixing vanes have a significant effect on both the DNB azimuthal location and the CHF value. - Without mixing vanes, DNB occurs mainly on the most central rod and preferentially at the azimuthal location facing the adjacent rod. - With mixing vanes, DNB can occur on any of the nine central rods and is distributed in an apparently random way around the rod. -The effect of the mixing vanes on CHF is dramatic and depends a great deal on the parameter range (pressure, local mass velocity and local quality). Generally speaking, CHF with mixing vanes is significantly higher than without mixing vanes, but this effect can be inverted in some cases.In order to understand this fact more clearly, it is necessary to perform detailed analysis of subchannel behavior. Indeed, the analyses show that the magnitude of this effect is closely related to the mixing coefficients used. These mixing coefficients, estimated from the single-phase flow experiments, are subject to large uncertainties in two-phase flow. ((orig.))

Spectral measurements in critical assemblies: MCNP specifications and calculated results

Energy Technology Data Exchange (ETDEWEB)

Stephanie C. Frankle; Judith F. Briesmeister

1999-12-01

Recently, a suite of 86 criticality benchmarks for the Monte Carlo N-Particle (MCNP) transport code was developed, and the results of testing the ENDF/B-V and ENDF/B-VI data (through Release 2) were published. In addition to the standard k{sub eff} measurements, other experimental measurements were performed on a number of these benchmark assemblies. In particular, the Cross Section Evaluation Working Group (CSEWG) specifications contain experimental data for neutron leakage and central-flux measurements, central-fission ratio measurements, and activation ratio measurements. Additionally, there exists another set of fission reaction-rate measurements performed at the National Institute of Standards and Technology (NIST) utilizing a {sup 252}Cf source. This report will describe the leakage and central-flux measurements and show a comparison of experimental data to MCNP simulations performed using the ENDF/B-V and B-VI (Release 2) data libraries. Central-fission and activation reaction-rate measurements will be described, and the comparison of experimental data to MCNP simulations using available data libraries for each reaction of interest will be presented. Finally, the NIST fission reaction-rate measurements will be described. A comparison of MCNP results published previously with the current MCNP simulations will be presented for the NIST measurements, and a comparison of the current MCNP simulations to the experimental measurements will be presented.

Spectral measurements in critical assemblies: MCNP specifications and calculated results

International Nuclear Information System (INIS)

Frankle, Stephanie C.; Briesmeister, Judith F.

1999-01-01

Recently, a suite of 86 criticality benchmarks for the Monte Carlo N-Particle (MCNP) transport code was developed, and the results of testing the ENDF/B-V and ENDF/B-VI data (through Release 2) were published. In addition to the standard k eff measurements, other experimental measurements were performed on a number of these benchmark assemblies. In particular, the Cross Section Evaluation Working Group (CSEWG) specifications contain experimental data for neutron leakage and central-flux measurements, central-fission ratio measurements, and activation ratio measurements. Additionally, there exists another set of fission reaction-rate measurements performed at the National Institute of Standards and Technology (NIST) utilizing a 252 Cf source. This report will describe the leakage and central-flux measurements and show a comparison of experimental data to MCNP simulations performed using the ENDF/B-V and B-VI (Release 2) data libraries. Central-fission and activation reaction-rate measurements will be described, and the comparison of experimental data to MCNP simulations using available data libraries for each reaction of interest will be presented. Finally, the NIST fission reaction-rate measurements will be described. A comparison of MCNP results published previously with the current MCNP simulations will be presented for the NIST measurements, and a comparison of the current MCNP simulations to the experimental measurements will be presented

The Mailbox Computer System for the IAEA verification experiment on HEU downblending at the Portsmouth Gaseous Diffusion Plant

International Nuclear Information System (INIS)

Aronson, A.L.; Gordon, D.M.

2000-01-01

IN APRIL 1996, THE UNITED STATES (US) ADDED THE PORTSMOUTH GASEOUS DIFFUSION PLANT TO THE LIST OF FACILITIES ELIGIBLE FOR THE APPLICATION OF INTERNATIONAL ATOMIC ENERGY AGENCY (IAEA) SAFEGUARDS. AT THAT TIME, THE US PROPOSED THAT THE IAEA CARRY OUT A ''VERIFICATION EXPERIMENT'' AT THE PLANT WITH RESPECT TO DOOWNBLENDING OF ABOUT 13 METRIC TONS OF HIGHLY ENRICHED URANIUM (HEU) IN THE FORM OF URANIUM HEXAFLUROIDE (UF6). DURING THE PERIOD DECEMBER 1997 THROUGH JULY 1998, THE IAEA CARRIED OUT THE REQUESTED VERIFICATION EXPERIMENT. THE VERIFICATION APPROACH USED FOR THIS EXPERIMENT INCLUDED, AMONG OTHER MEASURES, THE ENTRY OF PROCESS-OPERATIONAL DATA BY THE FACILITY OPERATOR ON A NEAR-REAL-TIME BASIS INTO A ''MAILBOX'' COMPUTER LOCATED WITHIN A TAMPER-INDICATING ENCLOSURE SEALED BY THE IAEA

Microstructure and Physical Metallurgy in Melt-Dilute Treatment Technology for Al-Based Spent Nuclear Fuel

International Nuclear Information System (INIS)

Adams, T.M.; Peacock, H.B.

1998-09-01

Major challenges associated with the direct disposal of research reactor fuel in a repository include nonproliferation and criticality control, both of which may be a concern for HEU Al-SNF. Consideration must be given to the potential desirability and/or regulatory necessity of diluting the HEU SNF to below 20 percent enrichment. The probability for a criticality event as well as the issue of proliferation are greatly decreased by reducing the enrichment. The melt-dilute technology development program is focused on the development and implementation of a treatment technology for diluting HEU Al-SNF to LEU levels and qualifying this LEU Al-SNF form for geologic repository storage. An attribute of the melt-dilute process is its applicability to various types of FRR and DRR SNF

The development of depletion program coupled with Monte Carlo computer code

International Nuclear Information System (INIS)

Nguyen Kien Cuong; Huynh Ton Nghiem; Vuong Huu Tan

2015-01-01

The paper presents the development of depletion code for light water reactor coupled with MCNP5 code called the MCDL code (Monte Carlo Depletion for Light Water Reactor). The first order differential depletion system equations of 21 actinide isotopes and 50 fission product isotopes are solved by the Radau IIA Implicit Runge Kutta (IRK) method after receiving neutron flux, reaction rates in one group energy and multiplication factors for fuel pin, fuel assembly or whole reactor core from the calculation results of the MCNP5 code. The calculation for beryllium poisoning and cooling time is also integrated in the code. To verify and validate the MCDL code, high enriched uranium (HEU) and low enriched uranium (LEU) fuel assemblies VVR-M2 types and 89 fresh HEU fuel assemblies, 92 LEU fresh fuel assemblies cores of the Dalat Nuclear Research Reactor (DNRR) have been investigated and compared with the results calculated by the SRAC code and the MCNP R EBUS linkage system code. The results show good agreement between calculated data of the MCDL code and reference codes. (author)

Storage arrangement for nuclear reactor fuel assemblies

International Nuclear Information System (INIS)

Wade, E.E.

1977-01-01

Said invention is intended for providing an arrangement of spent fuel assembly storage inside which the space is efficiently used without accumulating a critical mass. The storage is provided for long fuel assemblies having along their longitudinal axis an active part containing the fuel and an inactive part empty of fuel. Said storage arrangement comprises a framework constituting some long-shaped cells designed so as each of them can receive a fuel assembly. Means of axial positioning of said assembly in a cell make it possible to support the fuel assemblies inside the framework according to a spacing ratio, along the cell axis, such as the active part of an assembly is adjacent to the inactive part of the adjacent assemblies [fr

Fission reactor critical experiments and analysis

International Nuclear Information System (INIS)

Anon.

1977-01-01

Work accomplished in support of nonweapons programs by LASL Group Q-14 is described. Included are efforts in basic critical measurements, nuclear criticality safety, a plasma core critical assembly, and reactivity coefficient measurements

Self-assembly of coiled coil peptides into nanoparticles vs 2-d plates: effects of assembly pathway

Science.gov (United States)

Kim, Kyunghee; Pochan, Darrin

Molecular solution assembly, or self-assembly, is a process by which ordered nanostructures or patterns are formed by non-covalent interactions during assembly. Biomimicry, the use of bioinspired molecules or biologically relevant materials, is an important area of self-assembly research with peptides serving a critical role as molecular tools. The morphology of peptide assemblies can be controlled by adjusting solution conditions such as the concentration of peptides, the temperature, and pH. Herein, spherical nanostructures, which have potential for creating an encapsulation system, are formed by self-assembly when coiled coil peptides are combined in solution. These peptides are homotrimeric and heterodimeric coiled-coil bundles and the homotrimer is connected with each of heterodimer through their external surfaces via disulfide bonds. The resultant covalent constructs could co-assemble into complementary trimeric hubs, respectively. The two peptide constructs are directly mixed and assembled in solution in order to produce either spherical particles or 2-d plates depending on the solution conditions and kinetic pathway of assembly. In particular, structural changes of the self-assembled peptides are explored by control of the thermal history of the assembly solution.

Existing experimental criticality data applicable to nuclear-fuel-transportation systems

International Nuclear Information System (INIS)

Bierman, S.R.

1983-02-01

Analytical techniques are generally relied upon in making criticality evaluations involving nuclear material outside reactors. For these evaluations to be accepted the calculations must be validated by comparison with experimental data for a known set of conditions having physical and neutronic characteristics similar to those conditions being evaluated analytically. The purpose of this report is to identify those existing experimental data that are suitable for use in verifying criticality calculations on nuclear fuel transportation systems. In addition, near term needs for additional data in this area are identified. Of the considerable amount of criticality data currently existing, that are applicable to non-reactor systems, those particularly suitable for use in support of nuclear material transportation systems have been identified and catalogued into the following groups: (1) critical assemblies of fuel rods in water; (2) critical assemblies of fuel rods in water containing soluble neutron absorbers; (3) critical assemblies containing solid neutron absorber; (4) critical assemblies of fuel rods in water with heavy metal reflectors; and (5) critical assemblies of fuel rods in water with irregular features. A listing of the current near term needs for additional data in each of the groups has been developed for future use in planning criticality research in support of nuclear fuel transportation systems. The criticality experiments needed to provide these data are briefly described and identified according to priority and relative cost of performing the experiments

Critical heat flux tests for a 12 finned-element assembly

Energy Technology Data Exchange (ETDEWEB)

Yang, J., E-mail: Jun.Yang@cnl.ca; Groeneveld, D.C.; Yuan, L.Q.

2017-03-15

Highlights: • CHF tests for a 12 finned-fuel-element assembly at highly subcooled conditions. • Test approach to maximize experimental information and minimize heater failures. • Three series of tests were completed in vertical upward light water flow. • Bundle simulators of two axial power profiles and three heated lengths were tested. • Results confirm that the prediction method predicts lower CHF values than measured. - Abstract: An experimental study was undertaken to provide relevant data to validate the current critical heat flux (CHF) prediction method of the NRU driver fuel for safety analysis, i.e., to confirm no CHF occurrence below the predicted values. The NRU driver fuel assembly consists of twelve finned fuel elements arranged in two rings – three in the inner ring and nine in the outer ring. To satisfy the experimental objective tests at very high heat fluxes, very high mass velocities, and high subcoolings were conducted where the CHF mechanism is the departure from nucleate boiling (DNB). Such a CHF experiment can be very difficult, costly and time consuming since failure of the heating surface due to rupture or melting (physical burnout) is expected when the DNB type of CHF is reached. A novel experimental approach has been developed to maximize the amount of relevant experimental information on safe operating conditions in the tests, and to minimize any possible heater failures that inherently accompany the CHF occurrence at these conditions. Three series of tests using electrically heated NRU driver fuel simulators with three heated lengths and two axial power profiles (or axial heat flux distribution (AFD)) were completed in vertical upward light water flow. Each series of tests covered two mass flow rates, several heat flux levels, and local subcoolings that bound the ranges of interest for the analysis of postulated slow loss-of-regulation accident (LORA) and loss-of-flow accident (LOFA) scenarios. Tests for each mass flow rate of

Self assembly of anisotropic particles with critical Casimir forces

NARCIS (Netherlands)

Nguyễn, Trúc Anh

2016-01-01

Building new materials with structures on the micron and nanoscale presents a grand challenge currently. It requires fine control in the assembly of well-designed building blocks, and understanding of the mechanical, thermodynamic, and opto-electronic properties of the resulting structures. Patchy

A neutronic feasibility study for LEU conversion of the High Flux Beam Reactor (HFBR)

International Nuclear Information System (INIS)

Pond, R.B.; Hanan, N.A.; Matos, J.E.

1997-01-01

A neutronic feasibility study for converting the High Flux Beam Reactor at Brookhaven National Laboratory from HEU to LEU fuel was performed at Argonne National Laboratory. The purpose of this study is to determine what LEU fuel density would be needed to provide fuel lifetime and neutron flux performance similar to the current HEU fuel. The results indicate that it is not possible to convert the HFBR to LEU fuel with the current reactor core configuration. To use LEU fuel, either the core needs to be reconfigured to increase the neutron thermalization or a new LEU reactor design needs to be considered. This paper presents results of reactor calculations for a reference 28-assembly HEU-fuel core configuration and for an alternative 18-assembly LEU-fuel core configuration with increased neutron thermalization. Neutronic studies show that similar in-core and ex-core neutron fluxes, and fuel cycle length can be achieved using high-density LEU fuel with about 6.1 gU/cm 3 in an altered reactor core configuration. However, hydraulic and safety analyses of the altered HFBR core configuration needs to be performed in order to establish the feasibility of this concept. (author)

Fast Neutron Spectrum Potassium Worth for Space Power Reactor Design Validation

Energy Technology Data Exchange (ETDEWEB)

Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Marshall, Margaret A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Briggs, J. Blair [Idaho National Lab. (INL), Idaho Falls, ID (United States); Tsiboulia, Anatoli [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rozhikhin, Yevgeniy [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mihalczo, John T. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-03-01

A variety of critical experiments were constructed of enriched uranium metal (oralloy ) during the 1960s and 1970s at the Oak Ridge Critical Experiments Facility (ORCEF) in support of criticality safety operations at the Y-12 Plant. The purposes of these experiments included the evaluation of storage, casting, and handling limits for the Y-12 Plant and providing data for verification of calculation methods and cross-sections for nuclear criticality safety applications. These included solid cylinders of various diameters, annuli of various inner and outer diameters, two and three interacting cylinders of various diameters, and graphite and polyethylene reflected cylinders and annuli. Of the hundreds of delayed critical experiments, one was performed that consisted of uranium metal annuli surrounding a potassium-filled, stainless steel can. The outer diameter of the annuli was approximately 13 inches (33.02 cm) with an inner diameter of 7 inches (17.78 cm). The diameter of the stainless steel can was 7 inches (17.78 cm). The critical height of the configurations was approximately 5.6 inches (14.224 cm). The uranium annulus consisted of multiple stacked rings, each with radial thicknesses of 1 inch (2.54 cm) and varying heights. A companion measurement was performed using empty stainless steel cans; the primary purpose of these experiments was to test the fast neutron cross sections of potassium as it was a candidate for coolant in some early space power reactor designs.The experimental measurements were performed on July 11, 1963, by J. T. Mihalczo and M. S. Wyatt (Ref. 1) with additional information in its corresponding logbook. Unreflected and unmoderated experiments with the same set of highly enriched uranium metal parts were performed at the Oak Ridge Critical Experiments Facility in the 1960s and are evaluated in the International Handbook for Evaluated Criticality Safety Benchmark Experiments (ICSBEP Handbook) with the identifier HEU MET FAST 051. Thin

A neutronics feasibility study for the LEU conversion of Poland's Maria research reactor

International Nuclear Information System (INIS)

Bretscher, M. M.

1998-01-01

The MARIA reactor is a high-flux multipurpose research reactor which is water-cooled and moderated with both beryllium and water. Standard HEU (80% 235 U)fuel assemblies consist of six concentric fuel tubes of a U-Al alloy clad in aluminum. Although the inventory of HEU (80%) fuel is nearly exhausted, a supply of highly-loaded 36%-enriched fuel assemblies is available at the reactor site. Neutronic equilibrium studies have been made to determine the relative performance of fuels with enrichments of 80%, 36% and 19.7%. These studies indicate that LEU (19.7%) densities of about 2.5 gU/cm 3 and 3.8 gU/cm 3 are required to match the performance of the MARIA reactor with 80%-enriched and with 36%-enriched fuels, respectively

Critical seeding density improves properties and translatability of self-assembling anatomically shaped knee menisci

Science.gov (United States)

Hadidi, Pasha; Yeh, Timothy C.; Hu, Jerry C.; Athanasiou, Kyriacos A.

2014-01-01

A recent development in the field of tissue engineering is the rise of all-biologic, scaffold-free engineered tissues. Since these biomaterials rely primarily upon cells, investigation of initial seeding densities constitutes a particularly relevant aim for tissue engineers. In this study, a scaffold-free method was used to create fibrocartilage in the shape of the rabbit knee meniscus. The objectives of this study were: (i) to determine the minimum seeding density, normalized by an area of 44 mm2, necessary for the self-assembling process of fibrocartilage to occur, (ii) examine relevant biomechanical properties of engineered fibrocartilage, such as tensile and compressive stiffness and strength, and their relationship to seeding density, and (iii) identify a reduced, or optimal, number of cells needed to produce this biomaterial. It was found that a decreased initial seeding density, normalized by the area of the construct, produced superior mechanical and biochemical properties. Collagen per wet weight, glycosaminoglycans per wet weight, tensile properties, and compressive properties were all significantly greater in the 5 million cells per construct group as compared to the historical 20 million cells per construct group. Scanning electron microscopy demonstrated that a lower seeding density results in a denser tissue. Additionally, the translational potential of the self-assembling process for tissue engineering was improved though this investigation, as fewer cells may be used in the future. The results of this study underscore the potential for critical seeding densities to be investigated when researching scaffold-free engineered tissues. PMID:25234157

Evaluation of remote monitoring at the Oak Ridge HEU storage vault -- First thoughts and final application

International Nuclear Information System (INIS)

Sheely, K.B.; Whitaker, J.M.

1996-01-01

Remote monitoring provides a more timely and comprehensive way to meet national and international requirements for monitoring nuclear material inventories. Unattended monitoring technologies could be used to meet national needs for nuclear material safety, protection, control and accountability. Unattended systems possessing a remote data transmission capability could be used to meet international requirements for nuclear material safeguards and transparency. Even though more enhancements are required to improve system reliability, remote monitoring''s future potential seems great. The key questions are: (1) how will remote monitoring systems be used (configuration and operation); (2) how effective will the system be (vs. current activities); and (3) how much will it cost. This paper provides preliminary answers to these questions based on the experience gained from a joint IAEA-United States Support Program (USSP) task to evaluate remote monitoring at the Oak Ridge HEU Storage vault. This paper also draws on experience gained from US involvement in other remote monitoring projects

Numerical investigations on the effect of the axial interval between intensifying spacer grids on the critical heat flux value for fuel assemblies with non-uniform axial power distribution

International Nuclear Information System (INIS)

Kireeva, D.; Oleksyuk, D.

2015-01-01

In this paper a number of numerical studies on intensifying heat exchange conducted by NRC 'Kurchatov Institute' are presented. A standardised heat exchange intensifying spacer grid (UDRI) can be installed at any height along the fuel assembly (FA) heat-generating section. When installed at the bottom of a fuel assembly, the UDRI facilitates intensive coolant mixing; the UDRI mounted at the top of a FA provides better mixing and the enhancement in heat exchange. The application of the heat exchange intensifying spacer grids results in better flattening of the coolant parameters along the cross-section and higher critical heat flux ratio. The investigations were carried out by means of numerical code SC-INT using mesh generation that have been specially designed by NRC 'Kurchatov Institute' to perform calculations for fuel assemblies equipped with the intensifying spacer grids. The effect of the axial interval between UDRI grids on the critical heat flux value for two typical axial power shapes has been investigated. The derived optimal solutions for the positioning of intensifying grids are also presented

Numerical verification/validation of the theory of coupled reactors for deuterium critical assembly, using MCNP5 and Serpent codes

International Nuclear Information System (INIS)

Hussein, M.S; Lewis, B.J.; Bonin, H.W.

2013-01-01

The theory of multipoint coupled reactors developed by multi-group transport is verified by using the probabilistic transport code MCNP5 and the continuous-energy Monte Carlo reactor physics burnup calculation Serpent code. The verification was performed by calculating the multiplication factors (or criticality factors) and coupling coefficients for a two-region test reactor known as the Deuterium Critical Assembly, DCA. The multiplication factors k eff calculated numerically and independently from simulations of the DCA by MCNP5 and Serpent codes are compared with the multiplication factors k eff calculated based on the coupled reactor theory. Excellent agreement was obtained between the multiplication factors k eff calculated with the Serpent code, with MCNP5, and from the coupled reactor theory. This analysis demonstrates that the Serpent code is valid for the multipoint coupled reactor calculations. (author)

Numerical verification/validation of the theory of coupled reactors for deuterium critical assembly, using MCNP5 and Serpent codes

Energy Technology Data Exchange (ETDEWEB)

Hussein, M.S, E-mail: mohamed.hussein@rmc.ca [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada); Lewis, B.J., E-mail: Brent.Lewis@uoit.ca [Univ. of Ontario Inst. of Technology, Faculty of Energy Systems and Nuclear Science, Oshawa, Ontario (Canada); Bonin, H.W., E-mail: bonin-h@rmc.ca [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada)

2013-07-01

The theory of multipoint coupled reactors developed by multi-group transport is verified by using the probabilistic transport code MCNP5 and the continuous-energy Monte Carlo reactor physics burnup calculation Serpent code. The verification was performed by calculating the multiplication factors (or criticality factors) and coupling coefficients for a two-region test reactor known as the Deuterium Critical Assembly, DCA. The multiplication factors k{sub eff} calculated numerically and independently from simulations of the DCA by MCNP5 and Serpent codes are compared with the multiplication factors k{sub eff} calculated based on the coupled reactor theory. Excellent agreement was obtained between the multiplication factors k{sub eff} calculated with the Serpent code, with MCNP5, and from the coupled reactor theory. This analysis demonstrates that the Serpent code is valid for the multipoint coupled reactor calculations. (author)

Measurement of the ^235mU Production Cross Section Using a Critical Assembly*

Science.gov (United States)

Macri, Robert; Authier, Nicolas; Becker, John; Belier, Gilbert; Bond, Evelyn; Bredeweg, Todd; Glover, S.; Meot, Vincent; Rundberg, Robert; Vieira, David; Wilhelmy, Jerry

2006-10-01

Measurements of the creation and destruction cross sections for actinide nuclei constitute an important experimental effort in support of Stockpile Stewardship. In this talk I will give a progress report on the effort to measure the production cross section of the ^235mU isomer integrated over a fission neutron spectrum. This ongoing experiment is fielded at CEA in Valduc, France, taking advantage of the CALIBAN critical assembly. This effort is performed in collaboration with LANL, LLNL, Bruyeres le Chatel, and Valduc staff. This experiment utilizes a technique to measure internal conversion electrons from the ^235mU isomer with the French BIII detector (Bruyeres le Chatel), and involves a substantial chemistry effort (LANL) to prepare targets for irradiation and counting, as well as to remove fission fragments after irradiation. Experimental techniques will be discussed and preliminary data presented. *Work performed under the auspices of the U.S. Department of Energy by Los Alamos National Laboratory (W-7405-ENG-36) and Lawrence Livermore National Laboratory (W-7405-ENG-48), and CEA-DAM under CEA-DAM NNSA-DOE agreement.

OECD/NEA burnup credit criticality benchmarks phase IIIA: Criticality calculations of BWR spent fuel assemblies in storage and transport

Energy Technology Data Exchange (ETDEWEB)

Okuno, Hiroshi; Naito, Yoshitaka [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Ando, Yoshihira [Toshiba Corp., Kawasaki, Kanagawa (Japan)

2000-09-01

The report describes the final results of Phase IIIA Benchmarks conducted by the Burnup Credit Criticality Calculation Working Group under the auspices of the Nuclear Energy Agency of the Organization for Economic Cooperation and Development (OECD/NEA). The benchmarks are intended to confirm the predictive capability of the current computer code and data library combinations for the neutron multiplication factor (k{sub eff}) of a layer of irradiated BWR fuel assembly array model. In total 22 benchmark problems are proposed for calculations of k{sub eff}. The effects of following parameters are investigated: cooling time, inclusion/exclusion of FP nuclides and axial burnup profile, and inclusion of axial profile of void fraction or constant void fractions during burnup. Axial profiles of fractional fission rates are further requested for five cases out of the 22 problems. Twenty-one sets of results are presented, contributed by 17 institutes from 9 countries. The relative dispersion of k{sub eff} values calculated by the participants from the mean value is almost within the band of {+-}1%{delta}k/k. The deviations from the averaged calculated fission rate profiles are found to be within {+-}5% for most cases. (author)

Characterization of the CALIBAN Critical Assembly Neutron Spectra using Several Adjustment Methods Based on Activation Foils Measurement

Science.gov (United States)

Casoli, Pierre; Grégoire, Gilles; Rousseau, Guillaume; Jacquet, Xavier; Authier, Nicolas

2016-02-01

CALIBAN is a metallic critical assembly managed by the Criticality, Neutron Science and Measurement Department located on the French CEA Center of Valduc. The reactor is extensively used for benchmark experiments dedicated to the evaluation of nuclear data, for electronic hardening or to study the effect of the neutrons on various materials. Therefore CALIBAN irradiation characteristics and especially its central cavity neutron spectrum have to be very accurately evaluated. In order to strengthen our knowledge of this spectrum, several adjustment methods based on activation foils measurements are being studied for a few years in the laboratory. Firstly two codes included in the UMG package have been tested and compared: MAXED and GRAVEL. More recently, the CALIBAN cavity spectrum has been studied using CALMAR, a new adjustment tool currently under development at the CEA Center of Cadarache. The article will discuss and compare the results and the quality of spectrum rebuilding obtained with the UMG codes and with the CALMAR software, from a set of activation measurements carried out in the CALIBAN irradiation cavity.

Characterization of the CALIBAN Critical Assembly Neutron Spectra using Several Adjustment Methods Based on Activation Foils Measurement

Directory of Open Access Journals (Sweden)

Casoli Pierre

2016-01-01

Full Text Available CALIBAN is a metallic critical assembly managed by the Criticality, Neutron Science and Measurement Department located on the French CEA Center of Valduc. The reactor is extensively used for benchmark experiments dedicated to the evaluation of nuclear data, for electronic hardening or to study the effect of the neutrons on various materials. Therefore CALIBAN irradiation characteristics and especially its central cavity neutron spectrum have to be very accurately evaluated. In order to strengthen our knowledge of this spectrum, several adjustment methods based on activation foils measurements are being studied for a few years in the laboratory. Firstly two codes included in the UMG package have been tested and compared: MAXED and GRAVEL. More recently, the CALIBAN cavity spectrum has been studied using CALMAR, a new adjustment tool currently under development at the CEA Center of Cadarache. The article will discuss and compare the results and the quality of spectrum rebuilding obtained with the UMG codes and with the CALMAR software, from a set of activation measurements carried out in the CALIBAN irradiation cavity.

Low enrichment fuel conversion for Iowa State University. Final report

International Nuclear Information System (INIS)

Bullen, D.B.; Wendt, S.E.

1996-01-01

The UTR-10 research and teaching reactor at Iowa State University (ISU) has been converted from high-enriched fuel (HEU) to low- enriched fuel (LEU) under Grant No. DE-FG702-87ER75360 from the Department of Energy (DOE). The original contract period was August 1, 1987 to July 31, 1989. The contract was extended to February 28, 1991 without additional funding. Because of delays in receiving the LEU fuel and the requirement for disassembly of the HEU assemblies, the contract was renewed first through May 31, 1992, then through May 31, 1993 with additional funding, and then again through July 31, 1994 with no additional funding. In mid-August the BMI cask was delivered to Iowa State. Preparations are underway to ship the HEU fuel when NRC license amendments for the cask are approved

ENS RRFM '99. Transactions. Oral presentations and posters

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The presentations covered the following topics: neutron sources; fissile material supply, fuel fabrication and licensing procedures; research reactors operation and fuel safety issues; back-end options and spent fuel transportation. One of the most significant topics was the conversion from highly enriched uranium (HEU) fuel to low enriched uranium (LEU). The qualification of U{sub 3} Si{sub 2} is well advanced, and the validation of the newly designed U-Mo fuel assemblies, that should enable new conversions, is in progress. Concerning reprocessing the LEU appears to be more difficult to reprocess than HEU (silicide fuel). That is why research and development is conducted to produce LEU fuel with performance characteristics approximating HEU fuel. The issue of transportation of radioactive materials, above all spent fuel elements, from environmental and public acceptance point of view was of significant interest.

ENS RRFM '99. Transactions. Oral presentations and posters

International Nuclear Information System (INIS)

1999-01-01

The presentations covered the following topics: neutron sources; fissile material supply, fuel fabrication and licensing procedures; research reactors operation and fuel safety issues; back-end options and spent fuel transportation. One of the most significant topics was the conversion from highly enriched uranium (HEU) fuel to low enriched uranium (LEU). The qualification of U 3 Si 2 is well advanced, and the validation of the newly designed U-Mo fuel assemblies, that should enable new conversions, is in progress. Concerning reprocessing the LEU appears to be more difficult to reprocess than HEU (silicide fuel). That is why research and development is conducted to produce LEU fuel with performance characteristics approximating HEU fuel. The issue of transportation of radioactive materials, above all spent fuel elements, from environmental and public acceptance point of view was of significant interest

Criticality impacts on LWR fuel storage efficiency

International Nuclear Information System (INIS)

Napolitano, D.

1992-01-01

This presentation discusses the criticality impacts throughout storage of fuel onsite including new fuel storage, spent fuel storage, consolidation, and dry storage. The general principles for criticality safety are also be discussed. There is first an introduction which explains today's situation for criticality safety concerns. This is followed by a discussion of criticality safety Regulatory Guides, safety limits and fundamental principles. Design objectives for criticality safety in the 1990's include higher burnups, longer cycles, and higher enrichments which impact the criticality safety design. Criticality safety for new fuel storage, spent fuel storage, fuel consolidation, and dry storage are followed by conclusions. Today's situation is one in which the US does not reprocess, and does not have an operating MRS facility or repository. High density fuel storage rack designs of the 1980s, are filling up. Dry cask storage systems for spent fuel storage are being utilized. Enrichments continue to increase PWR fuel assemblies with enrichments of 4.5 to 5.0 weight percent U-235 and BWR fuel assemblies with enrichments of 3.25 to 3.5 weight percent U-235 are common. Criticality concerns affect the capacity and the economics of light water reactor (LWR) fuel storage arrays by dictating the spacing of fuel assemblies in a storage system, or the use of poisons or exotic materials in the storage system design

Neutron Activation and Thermoluminescent Detector Responses to a Bare Pulse of the CEA Valduc SILENE Critical Assembly

Energy Technology Data Exchange (ETDEWEB)

Miller, Thomas Martin [ORNL; Isbell, Kimberly McMahan [ORNL; Lee, Yi-kang [French Atomic Energy Commission (CEA), Centre de Saclay, Gif sur Yvette; Gagnier, Emmanuel [French Atomic Energy Commission (CEA), Centre de Saclay, Gif sur Yvette; Authier, Nicolas [French Atomic Energy Commission (CEA), Centre de Valduc, Is-sur-Tille; Piot, Jerome [French Atomic Energy Commission (CEA), Centre de Valduc, Is-sur-Tille; Jacquet, Xavier [French Atomic Energy Commission (CEA), Centre de Valduc, Is-sur-Tille; Rousseau, Guillaume [French Atomic Energy Commission (CEA), Centre de Valduc, Is-sur-Tille; Reynolds, Kevin H. [Y-12 National Security Complex

2016-09-01

This benchmark experiment was conducted as a joint venture between the US Department of Energy (DOE) and the French Commissariat à l'Energie Atomique (CEA). Staff at the Oak Ridge National Laboratory (ORNL) in the US and the Centre de Valduc in France planned this experiment. The experiment was conducted on October 11, 2010 in the SILENE critical assembly facility at Valduc. Several other organizations contributed to this experiment and the subsequent evaluation, including CEA Saclay, Lawrence Livermore National Laboratory (LLNL), the Y-12 National Security Complex (NSC), Babcock International Group in the United Kingdom, and Los Alamos National Laboratory (LANL). The goal of this experiment was to measure neutron activation and thermoluminescent dosimeter (TLD) doses from a source similar to a fissile solution critical excursion. The resulting benchmark can be used for validation of computer codes and nuclear data libraries as required when performing analysis of criticality accident alarm systems (CAASs). A secondary goal of this experiment was to qualitatively test performance of two CAAS detectors similar to those currently and formerly in use in some US DOE facilities. The detectors tested were the CIDAS MkX and the Rocky Flats NCD-91. These detectors were being evaluated to determine whether they would alarm, so they were not expected to generate benchmark quality data.

Monte Carlo analysis of Pu-H2O and UO2-PuO2-H2O critical assemblies with ENDF/B-IV data

International Nuclear Information System (INIS)

Hardy, J. Jr.; Ullo, J.J.

1981-04-01

A set of critical experiments, comprising thirteen homogeneous Pu-H 2 O assemblies and twelve UO 2 -PuO 2 lattices, was analyzed with ENDF/B-IV data and the RCPO1 Monte Carlo program, which modeled the experiments explicitly. Some major data sensitivities were also evaluated. For the Pu-H 2 O assemblies, calculated K/sub eff/ averaged 1.011. The large (2.7%) scatter of K/sub eff/ values for these assemblies was attributed mostly to uncertainties in physical specifications since no clear trends of K/sub eff/ were evident and data sensitivities were insignificant. The UO 2 -PuO 2 lattices showed just one trend of K/sub eff/, which indicated an overprediction of U238 capture consistent with that observed for uranium-H 2 O experiments. There was however a approx. 1% discrepancy in calculated K/sub eff/ between the two sets of UO 2 -PuO 2 lattices studied

Plutonium assemblies in reload 1 of the Dodewaard Reactor

International Nuclear Information System (INIS)

Bairiot, H.; Deramaix, P.; Vandenberg, C.; Leenders, L.; Mostert, P.

1977-01-01

Since 1963, Belgonucleaire has been developing the design of plutonium assemblies of the island type (i.e., plutonium rods inserted in the control zone of the assembly and enriched uranium rods at the periphery) for light water reactors. The application to boiling water reactors (BWRs) led to the introduction, in April 1971, of two prototype plutonium island assemblies in the Dodewaard BWR (The Netherlands): Those assemblies incorporating plutonium in 42 percent of the rods are interchangeable with standard uranium assemblies of the same reload. Their design, which had to meet these criteria, was performed using the routine order in use at Belgonucleaire; experimental checks included a mock-up configuration simulated in the VENUS critical facility at Mol and open-vessel cold critical experiments performed in the Dodewaard core. The pelleted plutonium rods were fabricated and controlled by Belgonucleaire following the manufacturing procedures developed at the production plant. In one of the assemblies, three vibrated plutonium fuel rods with a lower fuel density were introduced in the three most highly rated positions to reduce the power rating. Those plutonium assemblies experienced peak pellet ratings up to 535 W/cm and were discharged in April 1974 after having reached a mean burnup of approximately 21,000 MWd/MT. In-core instrumentation during operation, visual examinations, and reactivity substitution experiments during reactor shutdown did not indicate any special feature for those assemblies compared to the standard uranium assemblies, thereby demonstrating their interchangeability

Critical Configuration and Physics Measurements for Beryllium Reflected Assemblies of U(93.15)O₂ Fuel Rods (1.506-cm Pitch and 7-Tube Clusters)

Energy Technology Data Exchange (ETDEWEB)

Marshall, Margaret A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bess, John D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Briggs, J. Blair [Idaho National Lab. (INL), Idaho Falls, ID (United States); Murphy, Michael F. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mihalczo, John T. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-03-01

Cadmium ratios were measured with enriched uranium metal foils at various locations in the assembly with the fuel tube at the 1.506-cm spacing. They are described in the following subsections. The experiment configuration was the same as the first critical configuration described in HEU-COMP-FAST-004 (Case 1). The experimenter placed 0.75-cm-diameter × 0.010-cm-thick 93.15%-235U-enriched uranium metal foils with and without 0.051-cm-thick cadmium covers at various locations in the core and top reflector. One part of the cadmium cover was cupshape and contained the uranium foil. The other part was a lid that fit over the exposed side of the foil when it was in the cup shaped section of the cover. As can be seen in the logbook, two runs were required to obtain all the measurements necessary for the cadmium ratio. The bare foil measurements within the top reflector were run first as part of the axial foil activation measurements. The results of this run are used for both the axial activation results and the cadmium ratios. Cadmium covered foils were then placed at the same location through the top reflector in a different run. Three pairs of bare and cadmium covered foils were also placed through the core tank. One pair was placed at the axial center of a fuel tube 11.35 cm from the center of the core. Two pairs of foils were placed on top of fuel tubes 3.02 and 12.06 cm from the center of the core. The activation of the uranium metal foils was measured after removal from the assembly using two lead shielded NaI scintillation detectors as follows. The NaI scintillators were carefully matched and had detection efficiencies for counting delayed-fission-product gamma rays with energies above 250 KeV within 5%. In all foil activation measurements, one foil at a specific location was used as a normalizing foil to remove the effects of the decay of fission products during the counting measurements with the NaI detectors. The normalization foil was placed on one Na

Equation of State for Phospholipid Self-Assembly

DEFF Research Database (Denmark)

Marsh, Derek

2016-01-01

Phospholipid self-assembly is the basis of biomembrane stability. The entropy of transfer from water to self-assembled micelles of lysophosphatidylcholines and diacyl phosphatidylcholines with different chain lengths converges to a common value at a temperature of 44°C. The corresponding enthalpies...... of transfer converge at ∼-18°C. An equation of state for the free energy of self-assembly formulated from this thermodynamic data depends on the heat capacity of transfer as the sole parameter needed to specify a particular lipid. For lipids lacking calorimetric data, measurement of the critical micelle...

A neutronic feasibility study for LEU conversion of the WWR-M reactor at Gatchina

International Nuclear Information System (INIS)

Petrov, Yu. V.; Erykalov, A.N.; Onegin, M.S.

2000-01-01

In this report we present the results of computations of the full scale reactor core with HEU (90%), MEU (36%) and LEU (19.75%) fuel. The reactor computer model for the MCU RFFI Monte Carlo code includes all peculiarities of the core. Calculations show that a uranium density of 3.3gU/cm 3 of MEU (36%) fuel and 8/25gU/cm 3 of LEU (19.75%) in WWR-M5 fuel assembly (FA) geometry is required to match the fuel cycle length of the HEU (90%) case with the same end of cycle (EOEC) excess reactivity. For the equilibrium fuel cycle the fuel burnup and poisoning, the fast and thermal neutron fluxes, the reactivity worth of control rods were calculated for the reference case with HEU (90%) FA and for the MEU and LEU FA. The relative accuracy of this neutronic feasibility study of fuel enrichment reduction of the WWR-M reactor in Gatchina is sufficient to start the fabrication feasibility study of MEU (36%) WWR-M5 fuel assemblies. At the present stage of technology it seems hardly possible to manufacture LEU (19.75%) fuel elements in WWR-M5 geometry due to too high uranium density. Only a future R and D can solve the problem. (author)

Altered Toll-Like Receptor-4 Response to Lipopolysaccharides in Infants Exposed to HIV-1 and Its Preventive Therapy

Directory of Open Access Journals (Sweden)

Anicet Christel Maloupazoa Siawaya

2018-02-01

Full Text Available Pathogen sensing and recognition through pattern recognition receptors, and subsequent production of pro-inflammatory cytokines, is the cornerstone of the innate immune system. Despite the fact that HIV-exposed uninfected (HEU infants are prone to serious bacterial infections, no study has focused on the functionality of their bacteria recognition system. This is the first study to investigate baseline levels of three critically important immune response molecules in this population: complement component (C-3, toll-like receptor (TLR-4, and C-reactive protein (CRP. We enrolled 16 HEU and 6 HIV-unexposed (HU infants. TLR4 function was investigated by stimulating whole blood with increasing concentrations of TLR4-agonist ultrapure lipopolysaccharides. TLR4/TLR4-agonist dose response were assessed by measuring IL-6 secretion. Complement C3 and CRP were measured by photo spectrometry. Data showed no significant differences in baseline concentration of CRP between HEU and HU infants. Complement C3 was significantly higher in HEU infants than HU infants. TLR4 anergy was observed in 7 of 12 HEU infants, whereas the rest of HEU infants (n = 4 and the control HU infants tested (n = 3 showed responsive TLR4. None of the HEU infants investigated in this study had severe infections in the year after their birth. In conclusion, TLR4 anergy can occur in HEU infants without necessarily translating to increased vulnerability to infectious diseases.

Risk management for operations of the LANL Critical Experiments Facility

International Nuclear Information System (INIS)

Paternoster, R.; Butterfield, K.

1998-01-01

The Los Alamos Critical Experiments Facility (LACEF) currently operates two burst reactors (Godiva-IV and Skua), one solution assembly [the Solution High-Energy Burst Assembly (SHEBA)], two fast-spectrum benchmark assemblies (Flattop and Big Ten), and five general-purpose remote assembly machines that may be configured with nuclear materials and assembled by remote control. Special nuclear materials storage vaults support these and other operations at the site. With this diverse set of operations, several approaches are possible in the analysis and management of risk. The most conservative approach would be to write a safety analysis report (SAR) for each assembly and experiment. A more cost-effective approach is to analyze the probability and consequences of several classes of operations representative of operations on each critical assembly machine and envelope the bounding case accidents. Although the neutron physics of these machines varies widely, the operations performed at LACEF fall into four operational modes: steady-state mode, approach-to-critical mode, prompt burst mode, and nuclear material operations, which can include critical assembly fuel loading. The operational sequences of each mode are very nearly identical, whether operated on one assembly machine or another. The use of an envelope approach to accident analysis is facilitated by the use of classes of operations and the use of bounding case consequence analysis. A simple fault tree analysis of operational modes helps resolve which operations are sensitive to human error and which are initiated by hardware of software failures. Where possible, these errors and failures are blocked by TSR LCOs. Future work will determine the probability of accidents with various initiators

Technical specifications for the Oak Ridge Critical Experiments Facility

International Nuclear Information System (INIS)

Stinnett, R.M.

1986-01-01

These Technical Specifications for the Oak Ridge Critical Experiments Facility (CEF) delineate limiting conditions of operation for the facility. The CEF is used primarily for testing the High Flux Isotope Reactor (HFIR) fuel assemblies. Specifically, the Criticality Testing Unit, Liquid (CTUL), located in the CEF, is used for the HFIR fuel assembly test. The test is performed to satisfy the surveillance requirements of the HFIR Technical Specifications. The test is used to determine the water-submerged shutdown margin for each fuel assembly. 11 refs

SNEAK assembly 12B - Construction and experimental program

International Nuclear Information System (INIS)

Helm, F.

1982-10-01

The assembly SNEAK 12A is the second SNEAK assembly in which the neutron physics of disturbed material configurations, as they might occur in a postulated fast reactor accident, is investigated. The core is characterized by a central zone with fuel rods containing PuO 2 UO 2 mixed oxide pellets. This zone is cylindrically surrounded by a buffer zone for spectral adaptation, a driver zone sufficiently reactive to maintain criticality and a radial depleted uranium blanket. The purpose of the experiments is to test calculational methods of neutron physics which are used in the accident analysis of fast breeder reactors. The report describes the construction of the core and its assemblies and their content and outlines the foreseen experimental program. It includes measurements in the clean critical core and investigations of vertical and horizontal fuel relocations and steel blockages

Risk management for operations of the Los Alamos critical experiments facility

International Nuclear Information System (INIS)

Paternoster, R.; Butterfield, K.

1998-01-01

The Los Alamos Critical Experiments Facility (LACEF) currently operates two burst reactors (Godiva-IV and Skua), one solution assembly (SHEBA 2--Solution high-Energy Burst Assembly), two fast-spectrum benchmark assemblies (Flattop and Big Ten), and five general-purpose remote assembly machines which may be configured with nuclear materials and assembled by remote control. SNM storage vaults support these and other operations at the site. With this diverse set of operations, several approaches are possible in the analysis and management of risk. The most conservative approach would be to write a safety analysis report (SAR) for each assembly and experiment. A more cost-effective approach is to analyze the probability and consequences of several classes of operations representative of operations on each critical assembly machine and envelope the bounding case accidents. Although the neutron physics of these machines varies widely, the operations performed at LACEF fall into four operational modes: steady-state mode, approach-to-critical mode, prompt burst mode, and nuclear material operations which can include critical assembly fuel loading. The operational sequences of each mode are very nearly the same, whether operated on one assembly machine or another. The use of an envelope approach to accident analysis is facilitated by the use of classes of operations and the use of bounding case consequence analysis. A simple fault tree analysis of operational modes helps resolve which operations are sensitive to human error and which are initiated by hardware of software failures. Where possible, these errors and failures are blocked by TSR LCOs

A modification design and adjusting test for instruments and control system of critical assembly

International Nuclear Information System (INIS)

Wu Manrong; Li Guangjian

1996-12-01

A more reliable and safe control system and it's instruments for HFETRCA (high flux engineering test reactor critical assembly) have been built. In the system high performance CMOS unit was used, which has high integration, strong anti-interference and high trigger threshold. In the design of control rod driving circuit, the speed negative feedback principle was applied that results in more stable rotating rate of motors of transmission mechanism and more flexibility of adjusting rod speed. In order to improve reactor safety in accident, additional control circuit is equipped, by which not only control rods with electromagnet will rapidly drop but also other control rods will insert at the speed of 2∼6 times faster than the normal inserting speed. The key technique in the adjustment and new method of anti-interference are also introduced. After more than 40 times physical experiments with (4 x 4 - 4) fuel element in HFETRC, it is proved that the design and adjustment of the system is successful and they can be used as a reference to others. (3 figs., 2 tabs.)

Repository emplacement costs for Al-clad high enriched uranium spent fuel

International Nuclear Information System (INIS)

McDonell, W.R.; Parks, P.B.

1994-01-01

A range of strategies for treatment and packaging of Al-clad high-enriched uranium (HEU) spent fuels to prevent or delay the onset of criticality in a geologic repository was evaluated in terms of the number of canisters produced and associated repository costs incurred. The results indicated that strategies in which neutron poisons were added to consolidated forms of the U-Al alloy fuel generally produced the lowest number of canisters and associated repository costs. Chemical processing whereby the HEU was removed from the waste form was also a low cost option. The repository costs generally increased for isotopic dilution strategies, because of the substantial depleted uranium added. Chemical dissolution strategies without HEU removal were also penalized because of the inert constituents in the final waste glass form. Avoiding repository criticality by limiting the fissile mass content of each canister incurred the highest repository costs

Nondeterministic self-assembly of two tile types on a lattice.

Science.gov (United States)

Tesoro, S; Ahnert, S E

2016-04-01

Self-assembly is ubiquitous in nature, particularly in biology, where it underlies the formation of protein quaternary structure and protein aggregation. Quaternary structure assembles deterministically and performs a wide range of important functions in the cell, whereas protein aggregation is the hallmark of a number of diseases and represents a nondeterministic self-assembly process. Here we build on previous work on a lattice model of deterministic self-assembly to investigate nondeterministic self-assembly of single lattice tiles and mixtures of two tiles at varying relative concentrations. Despite limiting the simplicity of the model to two interface types, which results in 13 topologically distinct single tiles and 106 topologically distinct sets of two tiles, we observe a wide variety of concentration-dependent behaviors. Several two-tile sets display critical behaviors in the form of a sharp transition from bound to unbound structures as the relative concentration of one tile to another increases. Other sets exhibit gradual monotonic changes in structural density, or nonmonotonic changes, while again others show no concentration dependence at all. We catalog this extensive range of behaviors and present a model that provides a reasonably good estimate of the critical concentrations for a subset of the critical transitions. In addition, we show that the structures resulting from these tile sets are fractal, with one of two different fractal dimensions.

The Impact of Climatological Conditions on Low Enriched Uranium Loading Station Operations for the HEU Blend Down Project

International Nuclear Information System (INIS)

Chang, R.C.

2002-01-01

A computer model was developed using COREsim to perform a time motion study for the Low Enriched Uranium (LEU) Loading Station operations. The project is to blend Highly Enriched Uranium (HEU) with Natural Uranium (NU) to produce LEU to be shipped to Tennessee Valley Authority (TVA) for further processing. To cope with a project cost reduction, the LEU Loading Station concept has changed from an enclosed building with air-conditioning to a partially enclosed building without air conditioning. The LEU Loading Station is within a radiological contaminated area; two pairs of coveralls and negative pressure respirator are required. As a result, inclement weather conditions, especially heat stress, will affect and impact the LEU loading operations. The purposes of the study are to determine the climatological impacts on LEU Loading operations, resources required for committed throughputs, and to find out the optimum process pathways for multi crews working simultaneously in the space-lim ited LEU Loading Station

A programme for Euratom safeguards inspectors, used in the assay of high enriched (H.E.U.) and low enriched (L.E.U.) uranium fuel materials by active neutron interrogation

International Nuclear Information System (INIS)

Vocino, V.; Farese, N.; Maucq, T.; Nebuloni, M.

1991-01-01

The programme AECC (Active Euratom Coincidence Counters) has been developed at the Joint Research Center, Ispra by the Euratom Safeguards Directorate, Luxembourg and the Safety Technology Institute, Ispra for the acquisition, evaluation, management and storage of measurement data originating from active neutron interrogation of HEU and LEU fuel materials. The software accommodates the implementation of the NDA (Non Destructive Assay) procedures for the Active Well Coincidence Counters and Active Neutron Coincidence Counters deployed by the Euratom Safeguards Directorate, Luxembourg

Production, inventories and HEU in the world uranium market: Production's vital role

International Nuclear Information System (INIS)

Underhill, D.H.

1997-01-01

This paper analyses recent uranium supply and demand relationship and projects supply through 2010. The extremely depressed record low market prices have led to the ongoing annual inventory drawdown of over 25,000 t U resulting from the current 45% world production shortfall. The policy of the European Union and anti-dumping related activities in the USA are restricting imports of uranium from CIS producers to a majority of the world's nuclear utilities. These factors are reducing low priced uranium supply and forcing buyers to again obtain more of their requirements from producers. It discusses how the sale of Low Enriched Uranium (LEU) produced from of 550 t High Enriched Uranium (HEU) from Russia and Ukraine could potentially supply about 15% of world requirements through 2010. However, legislation currently being developed by the US Congress may ration the sale of this material, extending the LEU supply well into the next century. Nuclear generation capacity and its uranium requirements are projected to grow at about 1.5% through 2010. Demand for new uranium purchases is however, increasing at the much higher rate of 25-30% over the next 10-15 years. This increasing demand in the face of decreasing supply is resulting in a market recovery in which the spot price for non-CIS produced uranium has risen over 25% since October 1994. Prices will continue to increase as the market equilibrium shifts from a balance with alternative excess low priced supply to an equilibrium between production and demand. 19 refs, 14 figs, 2 tabs

Self assembly of rectangular shapes on concentration programming and probabilistic tile assembly models.

Science.gov (United States)

Kundeti, Vamsi; Rajasekaran, Sanguthevar

2012-06-01

Efficient tile sets for self assembling rectilinear shapes is of critical importance in algorithmic self assembly. A lower bound on the tile complexity of any deterministic self assembly system for an n × n square is [Formula: see text] (inferred from the Kolmogrov complexity). Deterministic self assembly systems with an optimal tile complexity have been designed for squares and related shapes in the past. However designing [Formula: see text] unique tiles specific to a shape is still an intensive task in the laboratory. On the other hand copies of a tile can be made rapidly using PCR (polymerase chain reaction) experiments. This led to the study of self assembly on tile concentration programming models. We present two major results in this paper on the concentration programming model. First we show how to self assemble rectangles with a fixed aspect ratio ( α:β ), with high probability, using Θ( α + β ) tiles. This result is much stronger than the existing results by Kao et al. (Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008) and Doty (Randomized self-assembly for exact shapes. In: proceedings of the 50th annual IEEE symposium on foundations of computer science (FOCS), IEEE, Atlanta. pp 85-94, 2009)-which can only self assembly squares and rely on tiles which perform binary arithmetic. On the other hand, our result is based on a technique called staircase sampling . This technique eliminates the need for sub-tiles which perform binary arithmetic, reduces the constant in the asymptotic bound, and eliminates the need for approximate frames (Kao et al. Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008). Our second result applies staircase sampling on the equimolar concentration programming model (The tile complexity of linear assemblies. In: proceedings of the 36th international colloquium automata, languages and programming: Part I on ICALP '09, Springer-Verlag, pp 235

Structural Aspects of Bacterial Outer Membrane Protein Assembly.

Science.gov (United States)

Calmettes, Charles; Judd, Andrew; Moraes, Trevor F

2015-01-01

The outer membrane of Gram-negative bacteria is predominantly populated by β-Barrel proteins and lipid anchored proteins that serve a variety of biological functions. The proper folding and assembly of these proteins is essential for bacterial viability and often plays a critical role in virulence and pathogenesis. The β-barrel assembly machinery (Bam) complex is responsible for the proper assembly of β-barrels into the outer membrane of Gram-negative bacteria, whereas the localization of lipoproteins (Lol) system is required for proper targeting of lipoproteins to the outer membrane.

Critical experiments AT Pacific Northwest Laboratory

International Nuclear Information System (INIS)

Clayton, E.D.; Bierman, S.R.

1984-01-01

After a short description of the facility, a brief listing of the principal types of fuel forms and assembly geometries is provided. A number of experiments have recently been performed on plain fissionable units, or isolated assemblies of single units, that include measurements on solutions composed of Pu-U mixtures and critical experiment data on lattices of low enriched uranium in water. Experiments have been performed on planar arrays of containers with Pu solutions because of the lack of data in this field concerning the safe storage of nuclear fuel; others have been conducted on arrays of low enriched U lattice assemblies. Neutronic measurements to date have shown they can be used to provide additional benchmark data for improvement and validation of criticality codes. Studies have previously been made to ascertain the need for critical experiments in support of fuel recycle operations. The result of an effort to update the list of needed critical experiments is summarized in this section. Experiments are listed in support of uranium based fuels and fast breeder reactor fuels. An effort is made to identify those areas within the fuel cycle wherein the critical experiment data would be applied and to identify the experiments (and data) required to fulfill the needs in each of these areas. The type and form of fuel on which the data would be obtained also are identified. In presenting this information, no attempt is made to describe the experiments in detail, or to define the actual number of critical experiments that might be needed to provide the required data

Critical experiments simulating accidental water immersion of highly enriched uranium dioxide fuel elements

International Nuclear Information System (INIS)

Ponomarev-Stepnoi, N.N.; Glushkov, L.S.

2003-01-01

The paper focuses on experimental analysis of nuclear criticality safety at accidental water immersion of fuel elements of the Russian TOPAZ-2 space nuclear power system reactor. The structure of water-moderated heterogeneous critical assemblies at the NARCISS facility is described in detail, including sizes, compositions, densities of materials of the main assembly components for various core configurations. Critical parameters of the assemblies measured for varying number of fuel elements, height of fuel material in fuel elements and their arrangement in the water moderator with a uniform or variable spacing are presented. It has been found from the experiments that at accidental water immersion of fuel elements involved, the minimum critical mass equal to approximately 20 kg of uranium dioxide is achieved at 31-37 fuel elements. The paper gives an example of a physical model of the water-moderated heterogeneous critical assembly with a detailed characterization of its main components that can be used for calculations using different neutronic codes, including Monte Carlo ones. (author)

Network spandrels reflect ecological assembly.

Science.gov (United States)

Maynard, Daniel S; Serván, Carlos A; Allesina, Stefano

2018-03-01

Ecological networks that exhibit stable dynamics should theoretically persist longer than those that fluctuate wildly. Thus, network structures which are over-represented in natural systems are often hypothesised to be either a cause or consequence of ecological stability. Rarely considered, however, is that these network structures can also be by-products of the processes that determine how new species attempt to join the community. Using a simulation approach in tandem with key results from random matrix theory, we illustrate how historical assembly mechanisms alter the structure of ecological networks. We demonstrate that different community assembly scenarios can lead to the emergence of structures that are often interpreted as evidence of 'selection for stability'. However, by controlling for the underlying selection pressures, we show that these assembly artefacts-or spandrels-are completely unrelated to stability or selection, and are instead by-products of how new species are introduced into the system. We propose that these network-assembly spandrels are critically overlooked aspects of network theory and stability analysis, and we illustrate how a failure to adequately account for historical assembly can lead to incorrect inference about the causes and consequences of ecological stability. © 2018 John Wiley & Sons Ltd/CNRS.

The Experience of Storage and Shipment for Reprocessing of HEU Nuclear Fuel Irradiated in the IRT-M Research Reactor and Pamir-630 Mobile Reactor

Energy Technology Data Exchange (ETDEWEB)

Sikorin, S. N.; Polazau, S. A.; Luneu, A. N.; Hrigarovich, T. K. [Joint Institute for Power and Nuclear Research–Sosny of the National Academy of Sciences of Belarus, Minsk (Belarus)

2014-08-15

At the end of 2010 under the Global Threat Reduction Initiative (GTRI), the Joint Institute for Power and Nuclear Research–“Sosny” (JIPNR–Sosny) of the National Academy of Sciences of the Republic of Belarus repatriated HEU spent nuclear fuel to the Russian Federation. The spent nuclear fuel was from the decommissioned Pamir-630D mobile reactor and IRT-M research reactor. The paper discusses the Pamir-630D spent nuclear fuel; experience and problems of spent nuclear fuel storage; and various aspects of the shipment including legal framework, preparation activities and shipment logistics. The conceptual project of a new research reactor for Belarus is also presented.

Nuclear criticality safety calculations for a K-25 site vacuum cleaner

International Nuclear Information System (INIS)

Shor, J.T.; Haire, M.J.

1997-02-01

A modified Nilfisk model GSJ dry vacuum cleaner is used throughout the K-25 Site to collect dry forms of highly enriched uranium (HEU). When vacuuming, solids are collected in a cyclone-type separator vacuum cleaner body. Calculations were done with the SCALE (KENO V.a) computer code to establish conditions at which a nuclear criticality event might occur if the vacuum cleaner was filled with fissile solution. Conditions evaluated included full (12-in. water) reflection and nominal (1-in. water) reflection, and full (100%) and 20% 235 U enrichment. Validation analyses of SCALE/KENO and the SCALE 27-group cross sections for nuclear criticality safety applications indicate that a calculated k eff + 2σ eff + 2σ ≥ 0.9605 is considered unsafe and may be critical. Critical conditions were calculated to be 70 g U/L for 100% 235 U and full 12-in. water reflection. This corresponds to a minimum critical mass of approximately 1,400 g 235 U for the approximate 20.0-L volume of the vacuum cleaner. The actual volume of the vacuum cleaner is smaller than the modeled volume because some internal materials of construction were assumed to be fissile solution. The model was an overestimate, for conservatism, of fissile solution occupancy. At nominal reflection conditions, the critical concentration in a vacuum cleaner full of UO 2 F 2 solution was calculated to be 100 g 235 U/L, or 2,000 g mass of 100% 235 U. At 20% 235 U for the 20.0-L volume of the vacuum cleaner. At 15% 235 U enrichment and full reflection, critical conditions were not reached at any possible concentration of uranium as a uranyl fluoride solution. At 17.5% 235 U enrichment, criticality was reached at approximately 1,300 g U/L which is beyond saturation at 25 C

Development of uranium metal targets for 99Mo production

International Nuclear Information System (INIS)

Wiencek, T.C.; Hofman, G.L.

1993-10-01

A substantial amount of high enriched uranium (HEU) is used for the production of medical-grade 99 Mo. Promising methods of producing irradiation targets are being developed and may lead to the reduction or elimination of this HEU use. To substitute low enriched uranium (LEU) for HEU in the production of 99 Mo, the target material may be changed to uranium metal foil. Methods of fabrication are being developed to simplify assembly and disassembly of the targets. Removal of the uranium foil after irradiation without dissolution of the cladding is a primary goal in order to reduce the amount of liquid radioactive waste material produced in the process. Proof-of-concept targets have been fabricated. Destructive testing indicates that acceptable contact between the uranium foil and the cladding can be achieved. Thermal annealing tests, which simulate the cladding/uranium diffusion conditions during irradiation, are underway. Plans are being made to irradiate test targets

Conversion (Utilizing LEU instead HEU) of research reactors in Czech Republic

International Nuclear Information System (INIS)

Matejka, K.; Sklenka, L.; Listik, E.; Ernest, J.

1998-01-01

This paper shortly describes some advantages on the RERTR-programme in the Czech Republic. Further calculations and experimental measurements finished on the VR-1 training reactor Sparrow. Paper brings results and its evaluation as well as one-year operation experiences with the Russian fuel assemblies IRT-3M and also operation experiments with mixed Core configuration (the Russian fuel assemblies IRT-2M with enrichment 80% 235 U and 36% 235 U) on the LVR-15 research reactor. (author)

30 CFR 7.45 - Critical characteristics

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Critical characteristics 7.45 Section 7.45 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND... characteristics The following critical characteristics shall be inspected or tested on each battery assembly to...

30 CFR 7.305 - Critical characteristics.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Critical characteristics. 7.305 Section 7.305 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR TESTING, EVALUATION, AND... characteristics. The following critical characteristics shall be inspected on each motor assembly to which an...

Some neutronics of innovative subcritical assembly with fast neutron spectrum

International Nuclear Information System (INIS)

Kiyavitskaya, H.; Fokov, Yu.; Rutkovskaya, Ch.; Sadovich, S.; Kasuk, D.; Gohar, Y.; Bolshinsky, I.

2013-01-01

Conclusion: • New assembly can be used to: • develop the experimental techniques and adapt the existing ones for monitoring the sub-criticality level, neutron spectra measurements, etc; • study the spatial kinetics of sub-critical and critical systems with fast neutron spectra; • measure the transmutation reaction rates of minor-actinides etc

Fuel assembly design for APR1400 with low CBC

Energy Technology Data Exchange (ETDEWEB)

Hah, Chang Joo, E-mail: changhah@kings.ac.kr [Department of NPP Engineering, KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2015-04-29

APR 1400 is a PWR (Pressurized Water Reactor) with rated power of 3983 MWth and 241 assemblies. Recently, demand for extremely longer cycle up to 24 months is increasing with challenge of higher critical boron concentration (CBC). In this paper, assembly design method of selecting Gd-rods is introduced to reduce CBC. The purpose of the method is to lower the critical boron concentration of the preliminary core loading pattern (PLP), and consequently to achieve more negative or less positive moderator temperature coefficient (MTC). In this method, both the ratio of the number of low-Gd rod to the number of high-Gd rod (r) and assembly average Gd wt% (w) are the decision variables. The target function is the amount of soluble boron concentration reduction, which can be converted to Δk{sub TARGET}. A set of new designed fuel assembly satisfies an objective function, min [f=∑{sub i}(Δk{sub FA}−Δk{sub i})], and enables a final loading pattern to reach a target CBC. The constraints required to determine a set of Δk are physically realizable pair, (r,w), and the sum of Δk of new designed assemblies as close to Δk{sub TARGET} as possible. New Gd-bearing assemblies selected based on valid pairs of (r,w) are replaced with existing assemblies in a PLP. This design methodology is applied to Shin-Kori Unit 3 Cycle 1 used as a reference model. CASMO-3/MASTER code is used for depletion calculation. CASMO-3/MASTER calculations with new designed assemblies produce lower CBC than the expected CBC, proving that the proposed method works successful.

Use of an oscillation technique to measure effective cross-sections of fissionable samples in critical assemblies

International Nuclear Information System (INIS)

Tretiakoff, O.; Vidal, R.; Carre, J.C.; Robin, M.

1964-01-01

The authors describe the technique used to measure the effective absorption and neutron-yield cross-sections of a fissionable sample. These two values are determined by analysing the signals due to the variation in reactivity (over-all signal) and the local perturbation in the flux (local signal) produced by the oscillating sample. These signals are standardized by means of a set of samples containing quantities of fissionable material ( 235 U) and an absorber, boron, which are well known. The measurements are made for different neutron spectra characterized by lattice parameters which constitute the central zone within which the sample moves. This technique is used to study the effective cross-sections of uranium-plutonium alloys for different heavy-water and graphite lattices in the MINERVE and MARIUS critical assemblies. The same experiments are carried out on fuel samples of different irradiations in order to determine the evolution of effective cross-sections as a function of the spectrum and the irradiations. (authors) [fr

Measurements in Los Alamos benchmark criticals and the central reactivity discrepancy

International Nuclear Information System (INIS)

Davey, W.G.; Hansen, G.E.; Koelling, J.J.; McLaughlin, T.P.

1978-01-01

Measurements in seven Los Alamos fast critical facilities are described; all are related to elucidating the causes of the central reactivity discrepancy in fast reactors. Specific capabilities of these specialized assemblies permit measurements well-above delayed critical and these confirm the validity of the delayed neutron data used for calibration; there is therefore no reactivity-scale error. Reactivity measurements in these homogeneous assemblies exhibit no discrepancy. It is concluded that nuclear data should not be adjusted to eliminate the discrepancy found in other, heterogeneous assemblies

Research reactor preparations for the air shipment of highly enriched uranium from Romania

International Nuclear Information System (INIS)

Bolshinsky, I.; Allen, K.J.; Biro, L.L.; Budu, M.E.; Zamfir, N.V.; Dragusin, M.; Paunoiu, C.; Ciocanescu, M.

2010-01-01

In June 2009 two air shipments transported both unirradiated (fresh) and irradiated (spent) Russian-origin highly enriched uranium (HEU) nuclear fuel from two research reactors in Romania to the Russian Federation (RF) for conversion to low enriched uranium (LEU). The Institute for Nuclear Research at Pitesti (SCN Pitesti) shipped 30.1 kg of HEU fresh fuel pellets to Dimitrovgrad, Russia and the Horia Hulubei National Institute of Physics and Nuclear Engineering (IFIN-HH) shipped 23.7 kilograms of HEU spent fuel assemblies from the VVR-S research reactor at Magurele, Romania, to Ozersk, Russia. Both HEU shipments were coordinated by the Russian Research Reactor Fuel Return Program (RRRFR) as part of the U.S. Department of Energy Global Threat Reduction Initiative (GTRI), were managed in Romania by the National Commission for Nuclear Activities Control (CNCAN), and were conducted in cooperation with the Russian Federation State Corporation for Atomic Energy Rosatom and the International Atomic Energy Agency (IAEA). Both shipments were transported by truck to and from respective commercial airports in Romania and the Russian Federation and stored at secure nuclear facilities in Russia until the material is converted into low enriched uranium. These shipments resulted in Romania becoming the 3rd country under the RRRFR program and the 14th country under the GTRI program to remove all HEU. This paper describes the research reactor preparations and license approvals that were necessary to safely and securely complete these air shipments of nuclear fuel. (author)

OECD/NEA burnup credit criticality benchmarks phase IIIB: Burnup calculations of BWR fuel assemblies for storage and transport

International Nuclear Information System (INIS)

Okuno, Hiroshi; Naito, Yoshitaka; Suyama, Kenya

2002-02-01

The report describes the final results of the Phase IIIB Benchmark conducted by the Expert Group on Burnup Credit Criticality Safety under the auspices of the Nuclear Energy Agency (NEA) of the Organization for Economic Cooperation and Development (OECD). The Benchmark was intended to compare the predictability of current computer code and data library combinations for the atomic number densities of an irradiated PWR fuel assembly model. The fuel assembly was irradiated under specific power of 25.6 MW/tHM up to 40 GWd/tHM and cooled for five years. The void fraction was assumed to be uniform throughout the channel box and constant, at 0, 40 and 70%, during burnup. In total, 16 results were submitted from 13 institutes of 7 countries. The calculated atomic number densities of 12 actinides and 20 fission product nuclides were found to be for the most part within a range of ±10% relative to the average, although some results, esp. 155 Eu and gadolinium isotopes, exceeded the band, which will require further investigation. Pin-wise burnup results agreed well among the participants. The results in the infinite neutron multiplication factor k ∞ also accorded well with each other for void fractions of 0 and 40%; however some results deviated from the averaged value noticeably for the void fraction of 70%. (author)

OECD/NEA burnup credit criticality benchmarks phase IIIB. Burnup calculations of BWR fuel assemblies for storage and transport

Energy Technology Data Exchange (ETDEWEB)

Okuno, Hiroshi; Naito, Yoshitaka; Suyama, Kenya [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-02-01

The report describes the final results of the Phase IIIB Benchmark conducted by the Expert Group on Burnup Credit Criticality Safety under the auspices of the Nuclear Energy Agency (NEA) of the Organization for Economic Cooperation and Development (OECD). The Benchmark was intended to compare the predictability of current computer code and data library combinations for the atomic number densities of an irradiated PWR fuel assembly model. The fuel assembly was irradiated under specific power of 25.6 MW/tHM up to 40 GWd/tHM and cooled for five years. The void fraction was assumed to be uniform throughout the channel box and constant, at 0, 40 and 70%, during burnup. In total, 16 results were submitted from 13 institutes of 7 countries. The calculated atomic number densities of 12 actinides and 20 fission product nuclides were found to be for the most part within a range of {+-}10% relative to the average, although some results, esp. {sup 155}Eu and gadolinium isotopes, exceeded the band, which will require further investigation. Pin-wise burnup results agreed well among the participants. The results in the infinite neutron multiplication factor k{sub {infinity}} also accorded well with each other for void fractions of 0 and 40%; however some results deviated from the averaged value noticeably for the void fraction of 70%. (author)

Critical factors for assembling a high volume of DNA barcodes

Science.gov (United States)

Hajibabaei, Mehrdad; deWaard, Jeremy R; Ivanova, Natalia V; Ratnasingham, Sujeevan; Dooh, Robert T; Kirk, Stephanie L; Mackie, Paula M; Hebert, Paul D.N

2005-01-01

Large-scale DNA barcoding projects are now moving toward activation while the creation of a comprehensive barcode library for eukaryotes will ultimately require the acquisition of some 100 million barcodes. To satisfy this need, analytical facilities must adopt protocols that can support the rapid, cost-effective assembly of barcodes. In this paper we discuss the prospects for establishing high volume DNA barcoding facilities by evaluating key steps in the analytical chain from specimens to barcodes. Alliances with members of the taxonomic community represent the most effective strategy for provisioning the analytical chain with specimens. The optimal protocols for DNA extraction and subsequent PCR amplification of the barcode region depend strongly on their condition, but production targets of 100K barcode records per year are now feasible for facilities working with compliant specimens. The analysis of museum collections is currently challenging, but PCR cocktails that combine polymerases with repair enzyme(s) promise future success. Barcode analysis is already a cost-effective option for species identification in some situations and this will increasingly be the case as reference libraries are assembled and analytical protocols are simplified. PMID:16214753

Directed Self-Assembly of Nanodispersions

Energy Technology Data Exchange (ETDEWEB)

Furst, Eric M [University of Delaware

2013-11-15

Directed self-assembly promises to be the technologically and economically optimal approach to industrial-scale nanotechnology, and will enable the realization of inexpensive, reproducible and active nanostructured materials with tailored photonic, transport and mechanical properties. These new nanomaterials will play a critical role in meeting the 21st century grand challenges of the US, including energy diversity and sustainability, national security and economic competitiveness. The goal of this work was to develop and fundamentally validate methods of directed selfassembly of nanomaterials and nanodispersion processing. The specific aims were: 1. Nanocolloid self-assembly and interactions in AC electric fields. In an effort to reduce the particle sizes used in AC electric field self-assembly to lengthscales, we propose detailed characterizations of field-driven structures and studies of the fundamental underlying particle interactions. We will utilize microscopy and light scattering to assess order-disorder transitions and self-assembled structures under a variety of field and physicochemical conditions. Optical trapping will be used to measure particle interactions. These experiments will be synergetic with calculations of the particle polarizability, enabling us to both validate interactions and predict the order-disorder transition for nanocolloids. 2. Assembly of anisotropic nanocolloids. Particle shape has profound effects on structure and flow behavior of dispersions, and greatly complicates their processing and self-assembly. The methods developed to study the self-assembled structures and underlying particle interactions for dispersions of isotropic nanocolloids will be extended to systems composed of anisotropic particles. This report reviews several key advances that have been made during this project, including, (1) advances in the measurement of particle polarization mechanisms underlying field-directed self-assembly, and (2) progress in the

Critical eigenvalue in LMFBRs: a physics assessment

International Nuclear Information System (INIS)

McKnight, R.D.; Collins, P.J.; Olsen, D.N.

1984-01-01

This paper summarizes recent work to put the analysis of past critical eigenvalue measurements from the US critical experiments program on a consistent basis. The integral data base includes 53 configurations built in 11 ZPPR assemblies which simulate mixed oxide LMFBRs. Both conventional and heterogeneous designs representing 350, 700, and 900 MWe sizes and with and without simulated control rods and/or control rod positions have been studied. The review of the integral data base includes quantitative assessment of experimental uncertainties in the measured excess reactivity. Analyses have been done with design level and higher-order methods using ENDF/B-IV data. Comparisons of these analyses with the experiments are used to generate recommended bias factors for criticality predictions. Recommended methods for analysis of LMFBR fast critical assemblies and LMFBR design calculations are presented. Unresolved issues and areas which require additional experimental or analytical study are identified

Micellar Self-Assembly of Recombinant Resilin-/Elastin-Like Block Copolypeptides.

Science.gov (United States)

Weitzhandler, Isaac; Dzuricky, Michael; Hoffmann, Ingo; Garcia Quiroz, Felipe; Gradzielski, Michael; Chilkoti, Ashutosh

2017-08-14

Reported here is the synthesis of perfectly sequence defined, monodisperse diblock copolypeptides of hydrophilic elastin-like and hydrophobic resilin-like polypeptide blocks and characterization of their self-assembly as a function of structural parameters by light scattering, cryo-TEM, and small-angle neutron scattering. A subset of these diblock copolypeptides exhibit lower critical solution temperature and upper critical solution temperature phase behavior and self-assemble into spherical or cylindrical micelles. Their morphologies are dictated by their chain length, degree of hydrophilicity, and hydrophilic weight fraction of the ELP block. We find that (1) independent of the length of the corona-forming ELP block there is a minimum threshold in the length of the RLP block below which self-assembly does not occur, but that once that threshold is crossed, (2) the RLP block length is a unique molecular parameter to independently tune self-assembly and (3) increasing the hydrophobicity of the corona-forming ELP drives a transition from spherical to cylindrical morphology. Unlike the self-assembly of purely ELP-based block copolymers, the self-assembly of RLP-ELPs can be understood by simple principles of polymer physics relating hydrophilic weight fraction and polymer-polymer and polymer-solvent interactions to micellar morphology, which is important as it provides a route for the de novo design of desired nanoscale morphologies from first principles.

Spatio-temporal Dynamics and Mechanisms of Stress Granule Assembly.

Directory of Open Access Journals (Sweden)

Daisuke Ohshima

2015-06-01

Full Text Available Stress granules (SGs are non-membranous cytoplasmic aggregates of mRNAs and related proteins, assembled in response to environmental stresses such as heat shock, hypoxia, endoplasmic reticulum (ER stress, chemicals (e.g. arsenite, and viral infections. SGs are hypothesized as a loci of mRNA triage and/or maintenance of proper translation capacity ratio to the pool of mRNAs. In brain ischemia, hippocampal CA3 neurons, which are resilient to ischemia, assemble SGs. In contrast, CA1 neurons, which are vulnerable to ischemia, do not assemble SGs. These results suggest a critical role SG plays in regards to cell fate decisions. Thus SG assembly along with its dynamics should determine the cell fate. However, the process that exactly determines the SG assembly dynamics is largely unknown. In this paper, analyses of experimental data and computer simulations were used to approach this problem. SGs were assembled as a result of applying arsenite to HeLa cells. The number of SGs increased after a short latent period, reached a maximum, then decreased during the application of arsenite. At the same time, the size of SGs grew larger and became localized at the perinuclear region. A minimal mathematical model was constructed, and stochastic simulations were run to test the modeling. Since SGs are discrete entities as there are only several tens of them in a cell, commonly used deterministic simulations could not be employed. The stochastic simulations replicated observed dynamics of SG assembly. In addition, these stochastic simulations predicted a gamma distribution relative to the size of SGs. This same distribution was also found in our experimental data suggesting the existence of multiple fusion steps in the SG assembly. Furthermore, we found that the initial steps in the SG assembly process and microtubules were critical to the dynamics. Thus our experiments and stochastic simulations presented a possible mechanism regulating SG assembly.

Criticality Safety Evaluation for the TACS at DAF

Energy Technology Data Exchange (ETDEWEB)

Percher, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heinrichs, D. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-06-10

Hands-on experimental training in the physical behavior of multiplying systems is one of ten key areas of training required for practitioners to become qualified in the discipline of criticality safety as identified in DOE-STD-1135-99, Guidance for Nuclear Criticality Safety Engineer Training and Qualification. This document is a criticality safety evaluation of the training activities and operations associated with HS-3201-P, Nuclear Criticality 4-Day Training Course (Practical). This course was designed to also address the training needs of nuclear criticality safety professionals under the auspices of the NNSA Nuclear Criticality Safety Program1. The hands-on, or laboratory, portion of the course will utilize the Training Assembly for Criticality Safety (TACS) and will be conducted in the Device Assembly Facility (DAF) at the Nevada Nuclear Security Site (NNSS). The training activities will be conducted by Lawrence Livermore National Laboratory following the requirements of an Integrated Work Sheet (IWS) and associated Safety Plan. Students will be allowed to handle the fissile material under the supervision of an LLNL Certified Fissile Material Handler.

Development of an Advanced Recycle Filter Tank Assembly for the ISS Urine Processor Assembly

Science.gov (United States)

Link, Dwight E., Jr.; Carter, Donald Layne; Higbie, Scott

2010-01-01

Recovering water from urine is a process that is critical to supporting larger crews for extended missions aboard the International Space Station. Urine is collected, preserved, and stored for processing into water and a concentrated brine solution that is highly toxic and must be contained to avoid exposure to the crew. The brine solution is collected in an accumulator tank, called a Recycle Filter Tank Assembly (RFTA) that must be replaced monthly and disposed in order to continue urine processing operations. In order to reduce resupply requirements, a new accumulator tank is being developed that can be emptied on orbit into existing ISS waste tanks. The new tank, called the Advanced Recycle Filter Tank Assembly (ARFTA) is a metal bellows tank that is designed to collect concentrated brine solution and empty by applying pressure to the bellows. This paper discusses the requirements and design of the ARFTA as well as integration into the urine processor assembly.

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 8 AND 9 CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wilson, Michael L.

2001-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 8 and 9 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Toward superconducting critical current by design

OpenAIRE

Sadovskyy, I. A.; Jia, Y.; Leroux, M.; Kwon, J.; Hu, H.; Fang, L.; Chaparro, C.; Zhu, S.; Welp, U.; Zuo, J. -M.; Zhang, Y.; Nakasaki, R.; Selvamanickam, V.; Crabtree, G. W.; Koshelev, A. E.

2015-01-01

We present the new paradigm of critical current by design. Analogous to materials by design, it aims at predicting the optimal defect landscape in a superconductor for targeted applications by elucidating the vortex dynamics responsible for the bulk critical current. To highlight this approach, we demonstrate the synergistic combination of critical current measurements on commercial high-temperature superconductors containing self-assembled and irradiation tailored correlated defects by using...

Criticality Calculations of Fresh LEU and MOX Assemblies for Transport and Storage at the Balakovo Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Goluoglu, S.

2001-01-11

Transportation of low-enriched uranium (LEU) and mixed-oxide (MOX) assemblies to and within the VVER-1000-type Balakovo Nuclear Power Plant is investigated. Effective multiplication factors for fresh fuel assemblies on the railroad platform, fresh fuel assemblies in the fuel transportation vehicle, and fresh fuel assemblies in the spent fuel storage pool are calculated. If there is no absorber between the units, the configurations with all MOX assemblies result in higher effective multiplication factors than the configurations with all LEU assemblies when the system is dry. When the system is flooded, the configurations with all LEU assemblies result in higher effective multiplication factors. For normal operating conditions, effective multiplication factors for all configurations are below the presumed upper subcritical limit of 0.95. For an accident condition of a fully loaded fuel transportation vehicle that is flooded with low-density water (possibly from a fire suppression system), the presumed upper subcritical limit is exceeded by configurations containing LEU assemblies.

Criticality safety concerns of uranium deposits in cascade equipment

International Nuclear Information System (INIS)

Plaster, M.J.

1996-01-01

The Paducah and Portsmouth Gaseous Diffusion Plants enrich uranium in the 235 U isotope by diffusing gaseous uranium hexafluoride (UF 6 ) through a porous barrier. The UF 6 gaseous diffusion cascade utilized several thousand open-quotes stagesclose quotes of barrier to produce highly enriched uranium (HEU). Historically, Portsmouth has enriched the Paducah Gaseous Diffusion Plant's product (typically 1.8 wt% 235 U) as well as natural enrichment feed stock up to 97 wt%. Due to the chemical reactivity of UF 6 , particularly with water, the formation of solid uranium deposits occur at a gaseous diffusion plant. Much of the equipment operates below atmospheric pressure, and deposits are formed when atmospheric air enters the cascade. Deposits may also be formed from UF 6 reactions with oil, UF 6 reactions with the metallic surfaces of equipment, and desublimation of UF 6 . The major deposits form as a result of moist air in leakage due to failure of compressor casing flanges, blow-off plates, seals, expansion joint convolutions, and instrument lines. This report describes criticality concerns and deposit disposition

Toward high throughput optical metamaterial assemblies.

Science.gov (United States)

Fontana, Jake; Ratna, Banahalli R

2015-11-01

Optical metamaterials have unique engineered optical properties. These properties arise from the careful organization of plasmonic elements. Transitioning these properties from laboratory experiments to functional materials may lead to disruptive technologies for controlling light. A significant issue impeding the realization of optical metamaterial devices is the need for robust and efficient assembly strategies to govern the order of the nanometer-sized elements while enabling macroscopic throughput. This mini-review critically highlights recent approaches and challenges in creating these artificial materials. As the ability to assemble optical metamaterials improves, new unforeseen opportunities may arise for revolutionary optical devices.

A neutronic feasibility study for LEU conversion of the Brookhaven Medical Research Reactor (BMRR).

Energy Technology Data Exchange (ETDEWEB)

Hanan, N. A.

1998-01-14

A neutronic feasibility study for converting the Brookhaven Medical Research Reactor from HEU to LEU fuel was performed at Argonne National Laboratory in cooperation with Brookhaven National Laboratory. Two possible LEU cores were identified that would provide nearly the same neutron flux and spectrum as the present HEU core at irradiation facilities that are used for Boron Neutron Capture Therapy and for animal research. One core has 17 and the other has 18 LEU MTR-type fuel assemblies with uranium densities of 2.5g U/cm{sup 3} or less in the fuel meat. This LEU fuel is fully-qualified for routine use. Thermal hydraulics and safety analyses need to be performed to complete the feasibility study.

Current status and future trends of the Russian RERTR program

International Nuclear Information System (INIS)

Bezzubtsev, V.; Arkhangelsky, N.; Aden, V.; Chernyshov, V.; Vatulin, A.

2003-01-01

The Russian program started at the end of 70's. The final goal of the program was to minimize and in perspective to eliminate using of HEU in fuel elements and assemblies supplied to foreign research reactors with the minimum of penalties for the experimenters. Later officials, scientists and engineers began political and scientific discussion about reducing enrichment domestic reactors as well as return of fresh and spent HEU fuel. Important issues of the Russian program is concerned with cooperation with USA, especially related to new types of LEU fuel elements development and fabrication to be used in Russian designed foreign research reactors. According to present results this goal will be achieved by 2006

Isotope Enrichment Detection by Laser Ablation - Laser Absorption Spectrometry: Automated Environmental Sampling and Laser-Based Analysis for HEU Detection

International Nuclear Information System (INIS)

Anheier, Norman C.; Bushaw, Bruce A.

2010-01-01

The global expansion of nuclear power, and consequently the uranium enrichment industry, requires the development of new safeguards technology to mitigate proliferation risks. Current enrichment monitoring instruments exist that provide only yes/no detection of highly enriched uranium (HEU) production. More accurate accountancy measurements are typically restricted to gamma-ray and weight measurements taken in cylinder storage yards. Analysis of environmental and cylinder content samples have much higher effectiveness, but this approach requires onsite sampling, shipping, and time-consuming laboratory analysis and reporting. Given that large modern gaseous centrifuge enrichment plants (GCEPs) can quickly produce a significant quantity (SQ ) of HEU, these limitations in verification suggest the need for more timely detection of potential facility misuse. The Pacific Northwest National Laboratory (PNNL) is developing an unattended safeguards instrument concept, combining continuous aerosol particulate collection with uranium isotope assay, to provide timely analysis of enrichment levels within low enriched uranium facilities. This approach is based on laser vaporization of aerosol particulate samples, followed by wavelength tuned laser diode spectroscopy to characterize the uranium isotopic ratio through subtle differences in atomic absorption wavelengths. Environmental sampling (ES) media from an integrated aerosol collector is introduced into a small, reduced pressure chamber, where a focused pulsed laser vaporizes material from a 10 to 20-(micro)m diameter spot of the surface of the sampling media. The plume of ejected material begins as high-temperature plasma that yields ions and atoms, as well as molecules and molecular ions. We concentrate on the plume of atomic vapor that remains after the plasma has expanded and then cooled by the surrounding cover gas. Tunable diode lasers are directed through this plume and each isotope is detected by monitoring absorbance

The initial criticality and nuclear commissioning test program at HANARO

Energy Technology Data Exchange (ETDEWEB)

Lee, Choong-Sung; Seo, Chul-Gyo; Jun, Byung-Jin [Korea Atomic Energy Research Institute, Dukjin-Dong 150, Yusung-Ku, Taejon, 305-353 (Korea, Republic of)

1995-07-01

The construction of the Korea Multipurpose Research Reactor - HANARO of 3MW, developed by Korea Atomic Energy Research Institute, was completed at the beginning of this year. The first fuel loading began on February 2 1995, and initial criticality was achieved on February 8, when the core had four 18-element assemblies and thirteen 36-element assemblies. The critical control rod position was 600.8 mm which represents excess reactivity of 0.71 $. Currently the nuclear commissioning test is on going under the zero power range. This paper describes the initial criticality approach of the HANARO, and its nuclear commissioning test program. (author)

Status and future program of reactor physics experiments in JAERI Critical facilities, FCA and TCA

International Nuclear Information System (INIS)

Okajima, Shigeaki; Osugi, Toshitaka; Nakajima, Ken; Suzaki, Takenori; Miyoshi, Yoshinori

1999-01-01

The critical facilities in JAERI, FCA (Fast Critical Assembly) and TCA (Tank-type Critical Assembly), have been used to provide integral data for evaluation of nuclear data as well as for development of various types of reactor since they went critical in 1960's. In this paper a review is presented on the experimental programs in both facilities. And the experimental programs in next 5 years are also shown. (author)

Current status of operation and utilization of the Dalat Research Reactor

International Nuclear Information System (INIS)

Dien, Nguyen Nhi

2006-01-01

The Dalat Nuclear Research Reactor (DNRR) is a 500 kW pool-type reactor using the HEU (36% enrichment) WWR-M2 fuel assemblies. It was renovated and upgraded from the USA 250 kW TRIGA Mark-II reactor. The first criticality of the renovated reactor was in the 1st November 1983 and its regular operation at nominal power of 500 kW has been since March 1984. The DNRR is operated mainly in continuous runs of 100 hrs, once every 4 weeks, for radioisotope production, neutron activation analysis, scientific research and training. The remaining time between two continuous runs is devoted to maintenance activities and also to short run for reactor physics and thermal hydraulics experiments. From the first start-up to the end of December 2004, it totaled about 27,253 hrs of operation and the total energy released was about 543 MWd. The first fuel reloading was executed in April 1994 after more than 10 years of operation with 89 fuel assemblies (FA). The 11 new FAs were added in the core periphery, at previous beryllium element locations. After reloading the working configuration of reactor core consisted of 100 FAs. The second fuel reloading was executed in March 2002. The 4 new FAs were added in the core periphery, at previous beryllium element locations. The working configuration of 104 FAs ensured efficient exploitation of the DNRR at nominal power for about 3000 hrs since March 2002. In order to provide excess reactivity for the reactor operation without the need to discharge high burned FAs, in June 2004, the fuel shuffling of the reactor core was done. 16 FAs with low burn-up from the core periphery were moved toward the core center and 16 FAs with high-burn-up from the core center were moved toward the core periphery. This operation provided additional reactivity of about 0.85 β eff that the current reactor configuration using re-shuffled HEU fuel is expected to allow normal operation until June 2006. In 1999, the request of returning to Russia HEU fuels from foreign

ANL Critical Assembly Covariance Matrix Generation - Addendum

Energy Technology Data Exchange (ETDEWEB)

McKnight, Richard D. [Argonne National Lab. (ANL), Argonne, IL (United States); Grimm, Karl N. [Argonne National Lab. (ANL), Argonne, IL (United States)

2014-01-13

In March 2012, a report was issued on covariance matrices for Argonne National Laboratory (ANL) critical experiments. That report detailed the theory behind the calculation of covariance matrices and the methodology used to determine the matrices for a set of 33 ANL experimental set-ups. Since that time, three new experiments have been evaluated and approved. This report essentially updates the previous report by adding in these new experiments to the preceding covariance matrix structure.

Performance evaluation of converted and upgraded PARR-1

International Nuclear Information System (INIS)

Pervez, Showket; Iqbal, Masood

1998-01-01

Pakistan Research Reactor-1 (PARR-1), a swimming pool MTR type research reactor which attained full power of 5 MW in June, 1996, with 93% high enriched uranium (HEU) fuel was converted to ,20% Low Enriched Uranium (LEU) fuel in october, 1991. The reactor power was also upgraded from 5 MW to 9 MW and then to 10 MW. Different critical and full power operational core configurations were assembled with the new fuel. The final equilibrium core was assembled with 27 standard fuel elements and five control fuel elements having a central flux trap facility for high neutron flux. detailed neutronics and thermal-hydraulic design calculations were made for the core conversion programme. After achieving the initial criticality several critical and power experiments were performed on the new core for the verification of design data and to determine the nuclear performance of the reactor. a comparison of the measured and the calculated results was also made. the results of the characteristics tests indicate that the performance of the new reactor is within the design limits. In flux trap thermal neutron flux is about 2x10 14 n.cm - 2. s - 1 which is five times higher than the average neutron flux of the core, seven standard and two control fuel elements have achieved designed burnup of 35%. Their physical inspection predicts excellent condition. (author)

SCALE-4 Analysis of LaSalle Unit 1 BWR Commercial Reactor Critical Configurations

International Nuclear Information System (INIS)

Gauld, I.C.

2000-01-01

Five commercial reactor criticals (CRCs) for the LaSalle Unit 1 boiling-water reactor have been analyzed using KENO V.a, the Monte Carlo criticality code of the SCALE 4 code system. The irradiated fuel assembly isotopics for the criticality analyses were provided by the Waste Package Design team at the Yucca Mountain Project in the US, who performed the depletion calculations using the SAS2H sequence of SCALE 4. The reactor critical measurements involved two beginning-of-cycle and three middle-of-cycle configurations. The CRCs involved relatively low-cycle burnups, and therefore contained a relatively high gadolinium poison content in the reactor assemblies. This report summarizes the data and methods used in analyzing the critical configurations and assesses the sensitivity of the results to some of the modeling approximations used to represent the gadolinium poison distribution within the assemblies. The KENO V.a calculations, performed using the SCALE 44GROUPNDF5 ENDF/B-V cross-section library, yield predicted k eff values within about 1% Δk/k relative to reactor measurements for the five CRCs using general 8-pin and 9-pin heterogeneous gadolinium poison pin assembly models

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Criticality calculations of a generic fuel container for fuel assemblies PWR, by means of the code MCNP

International Nuclear Information System (INIS)

Vargas E, S.; Esquivel E, J.; Ramirez S, J. R.

2013-10-01

The purpose of the concept of burned consideration (Burn-up credit) is determining the capacity of the calculation codes, as well as of the nuclear data associates to predict the isotopic composition and the corresponding neutrons effective multiplication factor in a generic container of spent fuel during some time of relevant storage. The present work has as objective determining this capacity of the calculation code MCNP in the prediction of the neutrons effective multiplication factor for a fuel assemblies arrangement type PWR inside a container of generic storage. The calculations are divided in two parts, the first, in the decay calculations with specified nuclide concentrations by the reference for a pressure water reactor (PWR) with enriched fuel to 4.5% and a discharge burned of 50 GW d/Mtu. The second, in criticality calculations with isotopic compositions dependent of the time for actinides and important fission products, taking 30 time steps, for two actinide groups and fission products. (Author)

A new flooding correlation development and its critical heat flux predictions under low air-water flow conditions in Savannah River Site assembly channels

International Nuclear Information System (INIS)

Lee, S.Y.

1993-01-01

The upper limit to countercurrent flow, namely, flooding, is important to analyze the reactor coolability during an emergency cooling system (ECS) phase as a result of a large-break loss-of-coolant accident (LOCA) such as a double-ended guillotine break in the Savannah River Site (SRS) reactor system. During normal operation, the reactor coolant system utilizes downward flow through concentric heated tubes with ribs, which subdivided each annular channel into four subchannels. In this paper, a new flooding correlation has been developed based on the analytical models and literature data for adiabatic, steady-state, one-dimensional, air-water flow to predict flooding phenomenon in the SRS reactor assembly channel, which may have a counter-current air-water flow pattern during the ECS phase. In addition, the correlation was benchmarked against the experimental data conducted under the Oak Ridge National Laboratory multislit channel, which is close to the SRS assembly geometry. Furthermore, the correlation has also been used as a constitutive relationship in a new two-component two-phase thermal-hydraulics code FLOWTRAN-TF, which has been developed for a detailed analysis of SRS reactor assembly behavior during LOCA scenarios. Finally, the flooding correlation was applied to the predictions of critical heat flux, and the results were compared with the data taken by the SRS heat transfer laboratory under a single annular channel with ribs and a multiannular prototypic test rig

Tests of the RBMK-1500 reactor fuel assemblies in the Leningrad reactor

International Nuclear Information System (INIS)

Aden, V.C.; Varovin, I.A.; Vorontsov, B.A.

1981-01-01

Test of fuel assemblies of the RBMK-1500 reactor is conducted in the reactor of the Leningrad NPP unit 2 for proving the calculational values of critical power of the RBMK-1500 reactor fuel assemblies adopted in design. The experiment presupposes the maximal approximation of the fuel assembly operation parameters to the calculational critical parameters without bringing into the mode of heat transfer crisis. The experiments are carried out at 500, 850 and 900 MW(el) of the reactor. The maximal channel power made up 472 kW at 20.5 t/h coolant flow rate and 49% mass steam content at the outlet of the channel. It was concluded that there was supply up to the heat transfer crisis in all the investigated modes. Data of temperature measurings of the fuel element cans, readings of the devices of the failure control system of the fuel element cans and external inspection of the assemblies after the tests testify to it [ru

Accident Analysis of High Density Storage Rack for Fresh Fuel Assemblies

International Nuclear Information System (INIS)

Jang, K. J.; Lee, M. J.; Jin, H. U.; Park, J. H.; Shin, S. Y.

2009-01-01

Recently KONES and KNF have developed the so called suspension-type High Density Storage Rack (HDSR) for fresh fuel assemblies. The USNRC OT position paper specifies that the design of the rack must ensure the functional integrity of the fuel racks under all credible fuel assembly drop events. In this context the functional integrity means the criticality safety. That is to say, the drop events must not bring any danger to the criticality safety of HDSR. This paper shows the results of the analysis carried out to demonstrate the regulatory compliance of the proposed racks under postulated accidental drop events

Reactivity accident analysis in MTR cores

International Nuclear Information System (INIS)

Waldman, R.M.; Vertullo, A.C.

1987-01-01

The purpose of the present work is the analysis of reactivity transients in MTR cores with LEU and HEU fuels. The analysis includes the following aspects: the phenomenology of the principal events of the accident that takes place, when a reactivity of more than 1$ is inserted in a critical core in less than 1 second. The description of the accident that happened in the RA-2 critical facility in September 1983. The evaluation of the accident from different points of view: a) Theoretical and qualitative analysis; b) Paret Code calculations; c) Comparison with Spert I and Cabri experiments and with post-accident inspections. Differences between LEU and HEU RA-2 cores. (Author)

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-07-30

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

Critical Assessment of Metagenome Interpretation

DEFF Research Database (Denmark)

Sczyrba, Alexander; Hofmann, Peter; Belmann, Peter

2017-01-01

Methods for assembly, taxonomic profiling and binning are key to interpreting metagenome data, but a lack of consensus about benchmarking complicates performance assessment. The Critical Assessment of Metagenome Interpretation (CAMI) challenge has engaged the global developer community to benchma...

Measuring method for effective neutron multiplication factor upon containing irradiated fuel assembly

International Nuclear Information System (INIS)

Ueda, Makoto; Mitsuhashi, Ishi; Sasaki, Tomoharu.

1993-01-01

A portion of irradiated fuel assemblies at a place where a reactivity effect is high, that is, at a place where neutron importance is high is replaced with standard fuel assemblies having a known composition to measure neutron fluxes at each of the places. An effective composition at the periphery of the standard fuel assemblies is determined by utilizing a calibration curve determined separately based on the composition and neutron flux values of the standard assemblies. By using the calibration curve determined separately based on this composition and the known composition of the standard fuel assemblies, an effective neutron multiplication factor for the fuel containing portion containing the irradiated fuel assemblies is recognized. Then, subcriticality is ensured and critical safety upon containing the fuel assemblies can be secured quantitatively. (N.H.)

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 1, 2, AND 3 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 1, 2, and 3 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Self-assembly behaviours of peptide-drug conjugates: influence of multiple factors on aggregate morphology and potential self-assembly mechanism

Science.gov (United States)

Fan, Qin; Ji, Yujie; Wang, Jingjing; Wu, Li; Li, Weidong; Chen, Rui; Chen, Zhipeng

2018-04-01

Peptide-drug conjugates (PDCs) as self-assembly prodrugs have the unique and specific features to build one-component nanomedicines. Supramolecular structure based on PDCs could form various morphologies ranging from nanotube, nanofibre, nanobelt to hydrogel. However, the assembly process of PDCs is too complex to predict or control. Herein, we investigated the effects of extrinsic factors on assembly morphology and the possible formation of nanostructures based on PDCs. To this end, we designed a PDC consisting of hydrophobic drug (S)-ketoprofen (Ket) and valine-glutamic acid dimeric repeats peptide (L-VEVE) to study their assembly behaviour. Our results showed that the critical assembly concentration of Ket-L-VEVE was 0.32 mM in water to form various nanostructures which experienced from micelle, nanorod, nanofibre to nanoribbon. The morphology was influenced by multiple factors including molecular design, assembly time, pH and hydrogen bond inhibitor. On the basis of experimental results, we speculated the possible assembly mechanism of Ket-L-VEVE. The π-π stacking interaction between Ket molecules could serve as an anchor, and hydrogen bonded-induced β-sheets and hydrophilic/hydrophobic balance between L-VEVE peptide play structure-directing role in forming filament-like or nanoribbon morphology. This work provides a new sight to rationally design and precisely control the nanostructure of PDCs based on aromatic fragment.

Tabular method of critical heat flux description in square packing rod bundles

International Nuclear Information System (INIS)

Bobkov, V.P.; Smogalev, I.P.

2003-01-01

Elaborations of harnessing tabular method for the description and calculation of critical heat fluxes in square packing rod bundles are presented. The tabular method for fuel rod triangular assemblies derived from using basic table for critical heat fluxes in triangular fuel assemblies demonstrates good results. For the harnessing tabular method in square packing rod bundles correction functions reflecting specific geometry were found. Comparative evaluations of calculated values for the critical heat fluxes with experimental ones are presented. Good agreement of calculations with experiments is noted in all range of parameters [ru

Neutron Activation Foil and Thermoluminescent Dosimeter Responses to a Lead Reflected Pulse of the CEA Valduc SILENE Critical Assembly

International Nuclear Information System (INIS)

Miller, Thomas Martin; Celik, Cihangir; Isbell, Kimberly McMahan; Lee, Yi-kang; Gagnier, Emmanuel; Authier, Nicolas; Piot, Jerome; Jacquet, Xavier; Rousseau, Guillaume; Reynolds, Kevin H.

2016-01-01

This benchmark experiment was conducted as a joint venture between the US Department of Energy (DOE) and the French Commissariat à l'Energie Atomique (CEA). Staff at the Oak Ridge National Laboratory (ORNL) in the US and the Centre de Valduc in France planned this experiment. The experiment was conducted on October 13, 2010 in the SILENE critical assembly facility at Valduc. Several other organizations contributed to this experiment and the subsequent evaluation, including CEA Saclay, Lawrence Livermore National Laboratory (LLNL), the Y-12 National Security Complex (NSC), Babcock International Group in the United Kingdom, and Los Alamos National Laboratory (LANL). The goal of this experiment was to measure neutron activation and thermoluminescent dosimeter (TLD) doses from a source similar to a fissile solution critical excursion. The resulting benchmark can be used for validation of computer codes and nuclear data libraries as required when performing analysis of criticality accident alarm systems (CAASs). A secondary goal of this experiment was to qualitatively test performance of two CAAS detectors similar to those currently and formerly in use in some US DOE facilities. The detectors tested were the CIDAS MkX and the Rocky Flats NCD-91. The CIDAS detects gammas with a Geiger-Muller tube, and the Rocky Flats detects neutrons via charged particles produced in a thin 6 LiF disc, depositing energy in a Si solid-state detector. These detectors were being evaluated to determine whether they would alarm, so they were not expected to generate benchmark quality data.

Neutron Activation Foil and Thermoluminescent Dosimeter Responses to a Polyethylene Reflected Pulse of the CEA Valduc SILENE Critical Assembly

International Nuclear Information System (INIS)

Miller, Thomas Martin; Celik, Cihangir; McMahan, Kimberly L.; Lee, Yi-kang; Gagnier, Emmanuel; Authier, Nicolas

2016-01-01

This benchmark experiment was conducted as a joint venture between the US Department of Energy (DOE) and the French Commissariat à l'Energie Atomique (CEA). Staff at the Oak Ridge National Laboratory (ORNL) in the US and the Centre de Valduc in France planned this experiment. The experiment was conducted on October 19, 2010 in the SILENE critical assembly facility at Valduc. Several other organizations contributed to this experiment and the subsequent evaluation, including CEA Saclay, Lawrence Livermore National Laboratory (LLNL), the Y-12 National Security Complex (NSC), Babcock International Group in the United Kingdom, and Los Alamos National Laboratory (LANL). The goal of this experiment was to measure neutron activation and thermoluminescent dosimeter (TLD) doses from a source similar to a fissile solution critical excursion. The resulting benchmark can be used for validation of computer codes and nuclear data libraries as required when performing analysis of criticality accident alarm systems (CAASs). A secondary goal of this experiment was to qualitatively test performance of two CAAS detectors similar to those currently and formerly in use in some US DOE facilities. The detectors tested were the CIDAS MkX and the Rocky Flats NCD-91. The CIDAS detects gammas with a Geiger-Muller tube and the Rocky Flats detects neutrons via charged particles produced in a thin "6LiF disc depositing energy in a Si solid state detector. These detectors were being evaluated to determine whether they would alarm, so they were not expected to generate benchmark quality data.

Neutron Activation Foil and Thermoluminescent Dosimeter Responses to a Polyethylene Reflected Pulse of the CEA Valduc SILENE Critical Assembly

Energy Technology Data Exchange (ETDEWEB)

Miller, Thomas Martin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Celik, Cihangir [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McMahan, Kimberly L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lee, Yi-kang [French Atomic Energy Commission (CEA), Saclay (France); Gagnier, Emmanuel [French Atomic Energy Commission (CEA), Centre de Saclay, Gif sur Yvette; Authier, Nicolas [French Atomic Energy Commission (CEA), Salives (France). Valduc Centre for Nuclear Studies; Piot, Jerome [French Atomic Energy Commission (CEA), Salives (France). Valduc Centre for Nuclear Studies; Jacquet, Xavier [French Atomic Energy Commission (CEA), Salives (France). Valduc Centre for Nuclear Studies; Rousseau, Guillaume [French Atomic Energy Commission (CEA), Salives (France). Valduc Centre for Nuclear Studies; Reynolds, Kevin H. [Y-12 National Security Complex, Oak Ridge, TN (United States)

2016-09-01

This benchmark experiment was conducted as a joint venture between the US Department of Energy (DOE) and the French Commissariat à l'Energie Atomique (CEA). Staff at the Oak Ridge National Laboratory (ORNL) in the US and the Centre de Valduc in France planned this experiment. The experiment was conducted on October 19, 2010 in the SILENE critical assembly facility at Valduc. Several other organizations contributed to this experiment and the subsequent evaluation, including CEA Saclay, Lawrence Livermore National Laboratory (LLNL), the Y-12 National Security Complex (NSC), Babcock International Group in the United Kingdom, and Los Alamos National Laboratory (LANL). The goal of this experiment was to measure neutron activation and thermoluminescent dosimeter (TLD) doses from a source similar to a fissile solution critical excursion. The resulting benchmark can be used for validation of computer codes and nuclear data libraries as required when performing analysis of criticality accident alarm systems (CAASs). A secondary goal of this experiment was to qualitatively test performance of two CAAS detectors similar to those currently and formerly in use in some US DOE facilities. The detectors tested were the CIDAS MkX and the Rocky Flats NCD-91. The CIDAS detects gammas with a Geiger-Muller tube and the Rocky Flats detects neutrons via charged particles produced in a thin ⁶LiF disc depositing energy in a Si solid state detector. These detectors were being evaluated to determine whether they would alarm, so they were not expected to generate benchmark quality data.

Neutron Activation Foil and Thermoluminescent Dosimeter Responses to a Lead Reflected Pulse of the CEA Valduc SILENE Critical Assembly

Energy Technology Data Exchange (ETDEWEB)

Miller, Thomas Martin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Celik, Cihangir [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Isbell, Kimberly McMahan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lee, Yi-kang [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Gagnier, Emmanuel [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Authier, Nicolas [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Piot, Jerome [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Jacquet, Xavier [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Rousseau, Guillaume [Commissariat a l' Energie Atomique et aux Energies Alternatives (CEA-Saclay), Gif-sur-Yvette (France); Reynolds, Kevin H. [Y-12 National Security Complex, Oak Ridge, TN (United States)

2016-09-01

This benchmark experiment was conducted as a joint venture between the US Department of Energy (DOE) and the French Commissariat à l'Energie Atomique (CEA). Staff at the Oak Ridge National Laboratory (ORNL) in the US and the Centre de Valduc in France planned this experiment. The experiment was conducted on October 13, 2010 in the SILENE critical assembly facility at Valduc. Several other organizations contributed to this experiment and the subsequent evaluation, including CEA Saclay, Lawrence Livermore National Laboratory (LLNL), the Y-12 National Security Complex (NSC), Babcock International Group in the United Kingdom, and Los Alamos National Laboratory (LANL). The goal of this experiment was to measure neutron activation and thermoluminescent dosimeter (TLD) doses from a source similar to a fissile solution critical excursion. The resulting benchmark can be used for validation of computer codes and nuclear data libraries as required when performing analysis of criticality accident alarm systems (CAASs). A secondary goal of this experiment was to qualitatively test performance of two CAAS detectors similar to those currently and formerly in use in some US DOE facilities. The detectors tested were the CIDAS MkX and the Rocky Flats NCD-91. The CIDAS detects gammas with a Geiger-Muller tube, and the Rocky Flats detects neutrons via charged particles produced in a thin ⁶LiF disc, depositing energy in a Si solid-state detector. These detectors were being evaluated to determine whether they would alarm, so they were not expected to generate benchmark quality data.

Calculated characteristics of subcritical assembly with anisotropic transport of neutrons

International Nuclear Information System (INIS)

Gorin, N.V.; Lipilina, E.N.; Lyutov, V.D.; Saukov, A.I.

2003-01-01

There was considered possibility of creating enough sub-critical system that multiply neutron fluence from a primary source by many orders. For assemblies with high neutron tie between parts, it is impossible. That is why there was developed a construction consisting of many units (cascades) having weak feedback with preceding cascades. The feedback attenuation was obtained placing layers of slow neutron absorber and moderators between the cascades of fission material. Anisotropy of fast neutron transport through the layers was used. The system consisted of many identical cascades aligning one by another. Each cascade consists of layers of moderator, fissile material and absorber of slow neutrons. The calculations were carried out using the code MCNP.4a with nuclear data library ENDF/B5. In this construction neutrons spread predominantly in one direction multiplying in each next fissile layer, and they attenuate considerably in the opposite direction. In a calculated construction, multiplication factor of one cascade is about 1.5 and multiplication factor of whole construction composed of n cascades is 1.5 n . Calculated keff value is 0.9 for one cascade and does not exceed 0.98 for a system containing any number of cascades. Therefore the assembly is always sub-critical and therefore it is safe in respect of criticality. There was considered using such a sub-critical assembly to create a powerful neutron fluence for neutron boron-capturing therapy. The system merits and demerits were discussed. (authors)

The Zeus Copper/Uranium Critical Experiment at NCERC

International Nuclear Information System (INIS)

Sanchez, Rene G.; Hayes, David K.; Bounds, John Alan; Jackman, Kevin R.; Goda, Joetta M.

2012-01-01

A critical experiment was performed to provide nuclear data in a non-thermal neutron spectrum and to reestablish experimental capability relevant to Stockpile Stewardship and Technical Nuclear Forensic programs. Irradiation foils were placed at specific locations in the Zeus all oralloy critical experiment to obtain fission ratios. These ratios were compared with others from other critical assemblies to assess the degree of softness in the neutron spectrum. This critical experiment was performed at the National Criticality Experiments Research Center (NCERC) in Nevada.

Maximum thermal loading test of BWR fuel assembly

International Nuclear Information System (INIS)

Nakajima, Yoshitaka; Yoshimura, Kunihiro; Nakamura, Satoshi; Ishizuka, Takao.

1987-01-01

Various proving tests on the reliability of nuclear power plants have been conducted at the Nuclear Power Engineering Test Center and at the Japan Power Plant Engineering and Inspection Corporation. The tests were initiated at the request of the Ministry of International Trade and Industry (MITI). Toshiba undertook one of the proving tests on the reliability of nuclear fuel assembly; the maximum thermal loading test of BWR fuel assembly from the Nuclear Power Engineering Test Center. These tests are part of the proving tests mentioned above, and their purpose is to confirm the reliability of the thermal hydraulic engineering techniques. Toshiba has been engaged for the past nine years in the design, fabrication and testing of the equipment. For the project, a test model fuel assembly was used to measure the critical power of the BWR fuel assembly and the void and fluidity of the coolant. From the test results, it has been confirmed that the heat is transferred safely from the fuel assembly to the coolant in the BWR nuclear power plant. In addition, the propriety and reliability of the thermal hydraulic engineering techniques for the fuel assembly have been proved. (author)

Neutron data error estimate of criticality calculations for lattice in shielding containers with metal fissionable materials

International Nuclear Information System (INIS)

Vasil'ev, A.P.; Krepkij, A.S.; Lukin, A.V.; Mikhal'kova, A.G.; Orlov, A.I.; Perezhogin, V.D.; Samojlova, L.Yu.; Sokolov, Yu.A.; Terekhin, V.A.; Chernukhin, Yu.I.

1991-01-01

Critical mass experiments were performed using assemblies which simulated one-dimensional lattice consisting of shielding containers with metal fissile materials. Calculations of the criticality of the above assemblies were carried out using the KLAN program with the BAS neutron constants. Errors in the calculations of the criticality for one-, two-, and three-dimensional lattices are estimated. 3 refs.; 1 tab

The congressional assault on RERTR

International Nuclear Information System (INIS)

Lyman, Edwin

2003-01-01

Since 9/11, there is a growing appreciation of the importance of the RERTR program and the effort to eliminate HEU commerce. That is why US DOE supports the 'Accelerated RERTR program'. But some legislative developments run contrary to this trend. This could result in loopholes that block completion of RERTR agenda. Current attempt in Congress si to weaken US HEU export controls by modifying the 'Schumer Amendment' - Right-wing criticism of DOE plan to convert US research reactors in the House of Representatives

ORALLOY (93.15 235U) METAL ANNULI WITH BERYLLIUM CORE

International Nuclear Information System (INIS)

Bess, John D.; Montierth, Leland M.; Reed, Raymond L.; Mihalczo, John T.

2010-01-01

A variety of critical experiments were constructed of enriched uranium metal during the 1960s and 1970s at the Oak Ridge Critical Experiments Facility (ORCEF) in support of criticality safety operations at the Y-12 Plant. The purposes of these experiments included the evaluation of storage, casting, and handling limits for the Y-12 Plant and providing data for verification of calculation methods and cross-sections for nuclear criticality safety applications. These included solid cylinders of various diameters, annuli of various inner and outer diameters, two and three interacting cylinders of various diameters, and graphite and polyethylene reflected cylinders and annuli. Of the hundreds of delayed critical experiments, two were performed that consisted of uranium metal annuli with a solid beryllium metal core. The outer diameter of the annuli was approximately 13 or 15 inches with an inner diameter of 7 inches. The diameter of the core was approximately 7 inches. The critical height of the configurations was approximately 5 and 4 inches, respectively. The uranium annuli consisted of multiple stacked rings with diametral thicknesses of approximately 2 inches apiece and varying heights. The 15-inch experiment was performed on June 4, 1963, and the 13-inch experiment on July 12, 1963 by J. T. Mihalczo and R. G. Taylor (Ref. 1) with accompanying logbook. Both detailed and simplified model specifications are provided in this evaluation. Both of these fast-spectra experiments were determined to represent acceptable benchmarks. The calculated eigenvalues for both the detailed and simple models are within approximately 0.6% of the benchmark values, but significantly greater than 3s from the benchmark value because the uncertainty in the benchmark is very small: eff of ∼0.67%. Unreflected and unmoderated experiments with the same highly enriched uranium metal parts were performed at the Oak Ridge Critical Experiments Facility in the 1960s and are evaluated in HEU MET

A Systematic Method of Assessing the Durability of Wood-Frame Wall Assemblies

DEFF Research Database (Denmark)

Lacasse, Michael A.; Morelli, Martin

2016-01-01

The long-term performance in respect to moisture management within any wall assembly depends on the hygrothermal response of the wall. Critical factors in estimating the longevity of wood-frame structures include limiting the temperature range, wood moisture content, and time of exposure to condi......The long-term performance in respect to moisture management within any wall assembly depends on the hygrothermal response of the wall. Critical factors in estimating the longevity of wood-frame structures include limiting the temperature range, wood moisture content, and time of exposure...... to the effects of moisture accumulation in wall cavities. Several approaches to assessing the vulnerability of wood-frame structures to deterioration have been developed in recent years, some of which suggest applying a limit-states design approach to the performance assessment of the assembly. In this paper......, a limit-states design approach is described that forms the basis of a performance assessment method for wood-frame wall assemblies. The approach is based on the requirements set out in ISO 13823. The approach, developed for the Moisture Management of Exterior Wall Systems (MEWS) project, is described...

Nuclear material attractiveness: an assessment of used-fuel assemblies

International Nuclear Information System (INIS)

Bathke, Charles Gary; Edelman, Paul G.; Hase, Kevin R.; Ebbinghaus, Bartley B.; Sleaford, Brad W.; Robel, Martin; Collins, B.A.; Prichard, Andrew W.; Smith, B Brian W.

2011-01-01

This paper examines the material attractiveness of used-fuel assemblies in a hypothetical scenario in which terrorists steal one or more assemblies in order to use the special nuclear materials (SNM) within an assembly in a nuclear explosive device. For assessing material attractiveness, this paper uses the Figure of Merit (FOM) that was used in earlier studies to examine the attractiveness of the SNM associated with the reprocessing of used light water reactor (LWR) fuel by various reprocessing schemes. However, for a theft scenario the mass used in the Acquisition Factor of the FOM is the mass of the stolen object conta ining SNM ; whereas the mass used for analyzing the material attractiveness of the products of various reprocessing schemes in the earlier studies was a fraction of the bare critical mass in recognition that a successful proliferator must avoid a criticality accident. This paper will indicate how long after discharge the radiation emanating from a cooling assembly is no longer self-protecting. Additionally, this paper will give the time scale for the SNM within the assembly to become more attractive. These studies were performed at the request of the United States Department of Energy (DOE), and are based on the calculation of ''attractiveness levels'' that has been couched in terms chosen for consistency with those normally used for nuclear materials in DOE nuclear facilities. The methodology and key findings will be presented. Additionally, this paper discusses how the results presented herein impact the application of safeguards and the securitization of SNM, and how they could be used to help inform policy makers.

2009 Community College Futures Assembly Focus: Leading Change--Leading in an Uncertain Environment

Science.gov (United States)

Campbell, Dale F.; Morris, Phillip A.

2009-01-01

The Community College Futures Assembly has served as a national, independent policy thinktank since 1995. Its purpose is to articulate the critical issues facing American community colleges and recognize innovative programs. Convening annually in January in Orlando, Florida, the Assembly offers a learning environment where tough questions are…

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-09-03

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies.

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies

Research project on accelerator-driven subcritical system using FFAG accelerator and Kyoto University critical assembly

International Nuclear Information System (INIS)

Mishima, Kaichiro; Unesaki, Hironobu; Misawa, Tsuyoshi; Tanigaki, Minoru; Mori, Yoshiharu; Shiroya, Seiji; Inoue, Makoto; Ishi, Y.; Fukumoto, Shintaro

2005-01-01

The KART (Kumatori Accelerator-driven Reactor Test facility) project started in Research Reactor Institute, Kyoto University in fiscal year 2002 with the grant by the Japanese Ministry of Education, Culture, Sports, Science and Technology. The purpose of this research project is to demonstrate the basis feasibility of accelerator driven system (ADS), studying the effect of incident neutron energy on the effective multiplication factor in a subcritical nuclear fuel system. For this purpose, a variable-energy FFAG (Fixed Field Alternating Gradient) accelerator complex is being constructed to be coupled with the Kyoto University Critical Assembly (KUCA). The FFAG proton accelerator complex consists of ion-beta, booster and main rings. This system aims to attain 1 μA proton beam with energy range from 20 to 150 MeV with a repetition rate of 120 Hz. The first beam from the FFAG complex is expected to be available by the end of FY 2005, and the experiment on ADS with KUCA and the FFAG complex (FFAG-KUCA experiment) will start in FY 2006. Before the FFAG-KUCA experiment starts, preliminary experiments with 14 MeV neutrons are currently being performed using a Cockcroft-Walton type accelerator coupled with the KUCA. Experimental data are analyzed using continuous energy Monte-Carlo codes MVP, MCNP and MNCP-X. (author)

Fellowship at orita: A critical analysis of the leadership crisis in the Assemblies of God, Nigeria

Directory of Open Access Journals (Sweden)

Williams O. Mbamalu

2016-07-01

Full Text Available This article is a critical analysis of the present crisis in the Assemblies of God, Nigeria (AGN. A background history of the church is given to show how growth had taken place and how decline had set in. Doing this involves analysing the factors responsible for the present crisis that has brought the church to its knees. The article finds that the AGN’s membership and leadership are dominated by the Igbo ethnic group whose worldviews are known to be highly competitive, individualistic and ‘pantomimic’. The AGN’s constitution and bye-laws do not include a clause that prevents pastors from the same ethnic group from holding the two top-most positions of the General Superintendent and the Assistant General Superintendent at the same time. Therefore the article submits that the AGN should amend its constitution to deal with these pertinent issues. The significance of the article is that it calls the attention of other Pentecostal denominations in Nigeria and the rest of Africa to the crisis-ridden AGN, whose eschatological and Pentecostal persuasion is at orita [the crossroads] and urges them to learn from it.

Reactor laboratory course for students majoring in nuclear engineering with the Kyoto University Critical Assembly (KUCA)

International Nuclear Information System (INIS)

Nishihara, H.; Shiroya, S.; Kanda, K.

1996-01-01

With the use of the Kyoto University Critical Assembly (KUCA), a joint reactor laboratory course of graduate level is offered every summer since 1975 by nine associated Japanese universities (Hokkaido University, Tohoku University, Tokyo Institute of Technology, Musashi Institute of Technology, Tokai University, Nagoya University, Osaka University, Kobe University of Mercantile Marine and Kyushu University) in addition to a reactor laboratory course of undergraduate level for Kyoto University. These courses are opened for three weeks (two weeks for the joint course and one week for the undergraduate course) to students majoring in nuclear engineering and a total of 1,360 students have taken the course in the last 21 years. The joint course has been institutionalized with the background that it is extremely difficult for a single university in Japan to have her own research or training reactor. By their effort, the united faculty team of the joint course have succeeded in giving an effective, unique one-week course, taking advantage of their collaboration. Last year, an enquete (questionnaire survey) was conducted to survey the needs for the educational experiments of graduate level and precious data have been obtained for promoting reactor laboratory courses. (author)

Safe operation of critical assemblies and research reactors. Code of practice and Technical appendix. 1971 ed

International Nuclear Information System (INIS)

Cox, J.

1971-01-01

This book is in two parts. The first is a Code of Practice for the Safe Operation of Critical Assemblies and Research Reactors, prepared as a result of a meeting of experts which took place in Vienna on 20-24 May 1968. The Code has been prepared by the International Atomic Energy Agency in co-operation with the World Health Organization, and its publication is sponsored by both organizations. In addition, the Code was approved by the Board of Governors of the International Atomic Energy Agency on 16 December 1968 as part of the Agency's safety standards, which are applied to operations undertaken by Member States with the assistance of the Agency. The Board, in approving the publication of the present book, also recommended Member States to take the Code into account in the formulation of national regulations and recommendations. The second part of the book is a Technical Appendix to give information and illustrative samples that would be helpful in implementing the Code of Practice. This second part, although published under the same cover, is not part of the Code. An extensive Bibliography, amplifying the Technical Appendix, is included at the end.

Construction of STACY (Static Experiment Critical Facility)

International Nuclear Information System (INIS)

Murakami, Kiyonobu; Onodera, Seiji; Hirose, Hideyuki

1998-08-01

Two critical assemblies, STACY (Static Experiment Critical Facility) and TRACY (Transient Experiment Critical Facility), were constructed in NUCEF (Nuclear Fuel Cycle Safety Engineering Research Facility) to promote researches on the criticality safety at a reprocessing facility. STACY aims at providing critical data of uranium nitrate solution, plutonium nitrate solution and their mixture while varying concentration of solution fuel, core tank shape and size and neutron reflecting condition. STACY achieved first criticality in February 1995, and passed the licensing inspection by STA (Science and Technology Agency of Japan) in May. After that a series of critical experiments commenced with 10 w/o enriched uranium solution. This report describes the outline of STACY at the end of FY 1996. (author)

Russian nuclear criticality experiments. Status and prospects

International Nuclear Information System (INIS)

Gagarinski, A.Yu.

2003-01-01

After the nuclear criticality had been reached on a uranium-graphite assembly for the first time in the Soviet Union on December 25, 1946, by I.V. Kurchatov and his team (1), the critical conditions in a great variety of multiplying media have been realized only in the Kurchatov Institute for at least several thousand times. Even the first Russian critical experiments carried out by Igor Kurchatov confirmed the unique merits of zero-power reactors: the most practically convenient range of parameters of kinetic response for variation of critical conditions, as well as invariability, over a wide range of the most important functions of neutron flux to reactor power. Neutron physics experiments have become a necessary stage in creation and improvement of nuclear reactors. Most critical experiments were performed mainly as a necessary stage of reactor design in the 60ies and 70ies, which has been the reactor 'golden age', when most of the total of over thousand nuclear reactors of various type and destination have been created worldwide. Though the ways of conducting critical measurements were very diversified, there are two main types of experiments. The first is so-called mock-up or prototype experiments when an exact (to the extent possible) simulation of the core is constructed to minimize the error in forecasting the operating reactor characteristics. Such experiments, which often represent the quality control of the core manufacturing and adjustment of core parameters to the design requirements, were carried out in Russia on critical assemblies of several plants, in design institutions (OKBM, Nizhni Novgorod; Electrostal and others), as well as in research centers (RRC 'Kurchatov Institute', etc.). Their results, which prevail today in the criticality database, even taking into account the capabilities provided by present-day calculation codes, are not well suited for new applications. It is hard to expect that the error resulting from inevitable idealization of

Cooperative effects of fibronectin matrix assembly and initial cell-substrate adhesion strength in cellular self-assembly.

Science.gov (United States)

Brennan, James R; Hocking, Denise C

2016-03-01

The cell-dependent polymerization of intercellular fibronectin fibrils can stimulate cells to self-assemble into multicellular structures. The local physical cues that support fibronectin-mediated cellular self-assembly are largely unknown. Here, fibronectin matrix analogs were used as synthetic adhesive substrates to model cell-matrix fibronectin fibrils having different integrin-binding specificity, affinity, and/or density. We utilized this model to quantitatively assess the relationship between adhesive forces derived from cell-substrate interactions and the ability of fibronectin fibril assembly to induce cellular self-assembly. Results indicate that the strength of initial, rather than mature, cell-substrate attachments correlates with the ability of substrates to support fibronectin-mediated cellular self-assembly. The cellular response to soluble fibronectin was bimodal and independent of the integrin-binding specificity of the substrate; increasing soluble fibronectin levels above a critical threshold increased aggregate cohesion on permissive substrates. Once aggregates formed, continuous fibronectin polymerization was necessary to maintain cohesion. During self-assembly, soluble fibronectin decreased cell-substrate adhesion strength and induced aggregate cohesion via a Rho-dependent mechanism, suggesting that the balance of contractile forces derived from fibronectin fibrils within cell-cell versus cell-substrate adhesions controls self-assembly and aggregate cohesion. Thus, initial cell-substrate attachment strength may provide a quantitative basis with which to build predictive models of fibronectin-mediated microtissue fabrication on a variety of substrates. Cellular self-assembly is a process by which cells and extracellular matrix (ECM) proteins spontaneously organize into three-dimensional (3D) tissues in the absence of external forces. Cellular self-assembly can be initiated in vitro, and represents a potential tool for tissue engineers to

Self-assembly via anisotropic interactions : Modeling association kinetics of patchy particle systems and self-assembly induced by critical Casimir forces

NARCIS (Netherlands)

Newton, A.C.

2017-01-01

Self-assembly, the non-dissipative spontaneous formation of structural order spans many length scales, from amphiphilic molecules forming micelles to stars forming galaxies. This thesis mainly deals with systems on the colloidal length scale where the size of a particle is between a nanometer and a

JCO criticality accident termination operation

OpenAIRE

金盛 正至

2010-01-01

In 2001, we summarized the circumstances surrounding termination of the JCO criticality accident based on testimony in the Mito District Court on December 17, 2001. JCO was the company for uranium fuels production in Japan. That document was assembled based on actual testimony in the belief that a description of the work involved in termination of the accident would be useful in some way for preventing nuclear disasters in the future. This year is the tenth year of the JCO criticality acciden...

Ultrasonic Examination of Jet Pump Diffuser Assemblies

International Nuclear Information System (INIS)

Hacker, M.; Levesque, M.; Whitman, G.

1998-01-01

In October 1997 the Boiling Water REactor Vessel and Internals Project (BWRVIP) issued the BWR Jet Pump Assembly Inspection and Flaw Evaluation Guidelines (BWRVIP-41). This document identified several welds on the jet pump diffuser assembly that are susceptible to Intergranular Stress Corrosion Cracking (IGSCC) or fatigue, and whose failure could result in jet pump disassembly. Based on the potential for failures, the document recommends inspection of 50% of the high priority welds at the next refueling outage for each BWR, with 100% expansion if flaws are identified. Because each diffuser assembly contains as many as six high priority welds, and access to these welds from the annulus is very restricted, implementing these recommendations can have a significant impact on outage critical path. In an effort to minimize the impact of implementing these recommendations, Framatome Technologies, Inc (FTI) developed a method to perform ultrasonic examinations of the jet pump diffuser assembly welds utilizing remotely operated equipment from the inner diameter (ID) of the diffuser assembly. This paper will discuss the tooling, ultrasonic methods, and delivery techniques used to perform the examinations, as well as the results obtained from a spring 1998 deployment of the system at a U.S. Nuclear Generating Plant. (Author)

Criticality evaluation of long term for spent fuel, using Scale

International Nuclear Information System (INIS)

Esquivel E, J.; Vargas E, S.; Ramirez S, J. R.

2013-10-01

Once carried out the spent fuel discharge, of the reactor core, this continues generating decay heat and diverse fission products, reason why is important to store this fuel inside containers able to dissipate the heat generated by the isotopes decay of the fuel and to maintain the fuels arrangement in subcritical condition. This means that: is necessary to assure the sub-criticality of those fuel assemblies in the time. This work, presents a criticality evaluation of fuel assemblies type PWR in a storage generic container. For this purpose have been used two codes: GeeWiz, to carry out the geometric model of the container with the fuel assemblies, and Keno, with which, the criticality of the full container with fuel is determined until a 10 6 years period. These codes are part of the package Scale. The specifications for each one of the analyzed components are based on a Benchmark document of the Nea/OECD, of where, the results that reports are compared with the obtained results by the realized analysis. (Author)

INTEGRATION OF SHIP HULL ASSEMBLY SEQUENCE PLANNING, SCHEDULING AND BUDGETING

Directory of Open Access Journals (Sweden)

Remigiusz Romuald Iwańkowicz

2015-02-01

Full Text Available The specificity of the yard work requires the particularly careful treatment of the issues of scheduling and budgeting in the production planning processes. The article presents the method of analysis of the assembly sequence taking into account the duration of individual activities and the demand for resources. A method of the critical path and resource budgeting were used. Modelling of the assembly was performed using the acyclic graphs. It has been shown that the assembly sequences can have very different feasible budget regions. The proposed model is applied to the assembly processes of large-scale welded structures, including the hulls of ships. The presented computational examples have a simulation character. They show the usefulness of the model and the possibility to use it in a variety of analyses.

ORALLOY (93.2 235U) METAL CYLINDER WITH BERYLLIUM TOP REFLECTOR

International Nuclear Information System (INIS)

Bess, John D.; Montierth, Leland M.; Reed, Raymond L.; Mihalczo, John T.

2010-01-01

A variety of critical experiments were constructed of enriched uranium metal during the 1960s and 1970s at the Oak Ridge Critical Experiments Facility (ORCEF) in support of criticality safety operations at the Y-12 Plant. The purposes of these experiments included the evaluation of storage, casting, and handling limits for the Y-12 Plant and providing data for verification of calculation methods and cross-sections for nuclear criticality safety applications. These included solid cylinders of various diameters, annuli of various inner and outer diameters, two and three interacting cylinders of various diameters, and graphite and polyethylene reflected cylinders and annuli. Of the hundreds of delayed critical experiments, one experiment was comprised of a stack of approximately 7-inch-diameter metal discs. The bottom of the stack consisted of uranium with an approximate height of 4-1/8 inches. The top of the stack consisted of beryllium with an approximate height of 5-9/16 inches. This experiment was performed on August 20, 1963 by J. T. Mihalczo and R. G. Taylor (Ref. 1) with accompanying logbook. Both detailed and simplified model specifications are provided in this evaluation. This fast-spectra experiment was determined to represent an acceptable benchmark. The calculated eigenvalues for both the detailed and simple models are within approximately 0.5% of the benchmark values, but significantly greater than 3s from the benchmark value because the uncertainty in the benchmark is very small: ±0.0002 (1s). There is significant variability between results using different neutron cross section libraries, the greatest being a k eff of ∼0.65% . Unreflected and unmoderated experiments with the same highly enriched uranium metal parts were performed at the Oak Ridge Critical Experiments Facility in the 1960s and are evaluated in HEU MET FAST 051. Thin graphite reflected (2 inches or less) experiments also using the same highly enriched uranium metal parts are evaluated

Safety analysis of the Los Alamos critical experiments facility: burst operation of Skua

International Nuclear Information System (INIS)

Orndoff, J.D.; Paxton, H.C.; Wimett, T.F.

1979-05-01

A detailed consideration of the Skua burst assembly is presented, thereby supplementing the facility safety analysis report covering the operation of other critical assemblies at Los Alamos. As with these assemblies the small fission-product inventory, ambient pressure, and moderate temperatures in Skua are amenable to straightforward measures to ensure the protection of the public

The first critical experiment with a new type of fuel assemblies IRT-3M on the training reactor VR-I

International Nuclear Information System (INIS)

Matejka, Karel; Sklenka, Lubomir

1997-01-01

The paper 'The first critical experiment with a new type of fuel assemblies IRT-3M on training reactor VR-1 presents basic information about the replacement of fuel on the reactor VR-1 run on FJFI CVUT in Prague. In spring 1997 the IRT-2M fuel type used till then was replaced by the IRT-3M type. When the fuel was replaced, no change in its enrichment was made, i.e. its level remained as 36% 235 U. The replacement itself was carried out in tight co-operation with the Nuclear Research Institute Rez plc., as related to the operation of the research reactor LVR-15. The fuel replacement on the VR-I reactor is a part of the international program RERTR (Reduced Enrichment for Research and Test Reactors) in which the Czech Republic participates. (author)

Pressure effects on lipids and bio-membrane assemblies

Directory of Open Access Journals (Sweden)

Nicholas J. Brooks

2014-11-01

Full Text Available Membranes are amongst the most important biological structures; they maintain the fundamental integrity of cells, compartmentalize regions within them and play an active role in a wide range of cellular processes. Pressure can play a key role in probing the structure and dynamics of membrane assemblies, and is also critical to the biology and adaptation of deep-sea organisms. This article presents an overview of the effect of pressure on the mesostructure of lipid membranes, bilayer organization and lipid–protein assemblies. It also summarizes recent developments in high-pressure structural instrumentation suitable for experiments on membranes.

A short review of critical experiments performed at the Kurchatov Institute

International Nuclear Information System (INIS)

Gagarinski, A.Yu.; Glushkov, Y.S.; Ponomarev-Stepnoi, N.N.

1997-01-01

Since the 1950s, the Institute of Atomic Energy (now the Russian Research Center Kurchatov Institute) has investigated nuclear reactors intended for various purposes. A summary of the present state of these assemblies is given in an attachment to the paper. A second attachment provides a brief description of critical experiments for small nuclear power systems intended for decentralized power generation. The critical assemblies for these experiments were moderated by water and zirconium hydride, and fuel elements ranged in enrichment from 5% to 95% uranium 235. 7 refs

A short review of critical experiments performed at the Kurchatov Institute

Energy Technology Data Exchange (ETDEWEB)

Gagarinski, A.Yu.; Glushkov, Y.S.; Ponomarev-Stepnoi, N.N. [Kurchatov Institute (Russian Federation)

1997-06-01

Since the 1950s, the Institute of Atomic Energy (now the Russian Research Center Kurchatov Institute) has investigated nuclear reactors intended for various purposes. A summary of the present state of these assemblies is given in an attachment to the paper. A second attachment provides a brief description of critical experiments for small nuclear power systems intended for decentralized power generation. The critical assemblies for these experiments were moderated by water and zirconium hydride, and fuel elements ranged in enrichment from 5% to 95% uranium 235. 7 refs.

Safety analysis of the Los Alamos critical experiments facility: burst operation of Skua

International Nuclear Information System (INIS)

Orndoff, J.D.; Paxton, H.C.; Wimett, T.F.

1980-12-01

Detailed consideration of the Skua burst assembly is provided, thereby supplementing the facility Safety Analysis Report covering the operation of other critical assemblies at the Los Alamos Scientific Laboratory. As with these assemblies the small fission-product inventory, ambient pressure, and moderate temperatures in Skua are amenable to straightforward measures to ensure the protection of the public

Improving transcriptome assembly through error correction of high-throughput sequence reads

Directory of Open Access Journals (Sweden)

Matthew D. MacManes

2013-07-01

Full Text Available The study of functional genomics, particularly in non-model organisms, has been dramatically improved over the last few years by the use of transcriptomes and RNAseq. While these studies are potentially extremely powerful, a computationally intensive procedure, the de novo construction of a reference transcriptome must be completed as a prerequisite to further analyses. The accurate reference is critically important as all downstream steps, including estimating transcript abundance are critically dependent on the construction of an accurate reference. Though a substantial amount of research has been done on assembly, only recently have the pre-assembly procedures been studied in detail. Specifically, several stand-alone error correction modules have been reported on and, while they have shown to be effective in reducing errors at the level of sequencing reads, how error correction impacts assembly accuracy is largely unknown. Here, we show via use of a simulated and empiric dataset, that applying error correction to sequencing reads has significant positive effects on assembly accuracy, and should be applied to all datasets. A complete collection of commands which will allow for the production of Reptile corrected reads is available at https://github.com/macmanes/error_correction/tree/master/scripts and as File S1.

Highly enriched uranium, a dangerous substance that should be eliminated

Energy Technology Data Exchange (ETDEWEB)

Schaper, Annette

2013-07-01

Research and Test Reactor (RERTR) program, new denser fuels for research reactors have successfully been developed. In many research reactors it was possible to replace the previous HEU fuel with a new fuel type without affecting performance. Only a few exceptions are left. The hope was, and is, that the remaining reactors will reach the end of their useful life so that in future no more HEU will be needed for this application. Indeed, there was a moratorium for two decades during which no new HEU-fuelled research reactor was constructed. The first reactor that breached this moratorium was the FRM-II in Garching near Munich. It made use of the newly developed fuels but in a way that resorted to HEU again. The decision-making on the reactor design neglected the political disadvantages for a long time, but stressed some technical advantages which, however, are disputed. Critics claim that a somewhat different design would have enabled the same applications. Discussions took place on both a domestic and international level. The lesson that can be learned is that proliferation danger criteria and foreign policy issues need to be made a part of the decision-making process at an early stage. A campaign has been initiated to convert medical targets in order to avoid the use of HEU. It is showing promising first results but will be successful only when an international consensus and commitment is reached. Only a few countries use HEU as fuel for naval reactors. The question arises why such reactors cannot be converted to different fuels. The most prominent opponents of banning the future production of HEU for naval fuel purposes are the U.S. and the UK. Their existing naval reactors could consume the huge excess quantities of HEU that these states possess. It would be sufficient for many decades. During this time, new naval reactors could be designed that use the new modern fuels based on LEU instead of HEU. Several states, including nuclear weapon states, use naval fuel made

Highly enriched uranium, a dangerous substance that should be eliminated

International Nuclear Information System (INIS)

Schaper, Annette

2013-01-01

Research and Test Reactor (RERTR) program, new denser fuels for research reactors have successfully been developed. In many research reactors it was possible to replace the previous HEU fuel with a new fuel type without affecting performance. Only a few exceptions are left. The hope was, and is, that the remaining reactors will reach the end of their useful life so that in future no more HEU will be needed for this application. Indeed, there was a moratorium for two decades during which no new HEU-fuelled research reactor was constructed. The first reactor that breached this moratorium was the FRM-II in Garching near Munich. It made use of the newly developed fuels but in a way that resorted to HEU again. The decision-making on the reactor design neglected the political disadvantages for a long time, but stressed some technical advantages which, however, are disputed. Critics claim that a somewhat different design would have enabled the same applications. Discussions took place on both a domestic and international level. The lesson that can be learned is that proliferation danger criteria and foreign policy issues need to be made a part of the decision-making process at an early stage. A campaign has been initiated to convert medical targets in order to avoid the use of HEU. It is showing promising first results but will be successful only when an international consensus and commitment is reached. Only a few countries use HEU as fuel for naval reactors. The question arises why such reactors cannot be converted to different fuels. The most prominent opponents of banning the future production of HEU for naval fuel purposes are the U.S. and the UK. Their existing naval reactors could consume the huge excess quantities of HEU that these states possess. It would be sufficient for many decades. During this time, new naval reactors could be designed that use the new modern fuels based on LEU instead of HEU. Several states, including nuclear weapon states, use naval fuel made

Critical experiments at Sandia National Laboratories

International Nuclear Information System (INIS)

Harms, Gary A.; Ford, John T.; Barber, Allison Delo

2010-01-01

Sandia National Laboratories (SNL) has conducted radiation effects testing for the Department of Energy (DOE) and other contractors supporting the DOE since the 1960's. Over this period, the research reactor facilities at Sandia have had a primary mission to provide appropriate nuclear radiation environments for radiation testing and qualification of electronic components and other devices. The current generation of reactors includes the Annular Core Research Reactor (ACRR), a water-moderated pool-type reactor, fueled by elements constructed from UO2-BeO ceramic fuel pellets, and the Sandia Pulse Reactor III (SPR-III), a bare metal fast burst reactor utilizing a uranium-molybdenum alloy fuel. The SPR-III is currently defueled. The SPR Facility (SPRF) has hosted a series of critical experiments. A purpose-built critical experiment was first operated at the SPRF in the late 1980's. This experiment, called the Space Nuclear Thermal Propulsion Critical Experiment (CX), was designed to explore the reactor physics of a nuclear thermal rocket motor. This experiment was fueled with highly-enriched uranium carbide fuel in annular water-moderated fuel elements. The experiment program was completed and the fuel for the experiment was moved off-site. A second critical experiment, the Burnup Credit Critical Experiment (BUCCX) was operated at Sandia in 2002. The critical assembly for this experiment was based on the assembly used in the CX modified to accommodate low-enriched pin-type fuel in water moderator. This experiment was designed as a platform in which the reactivity effects of specific fission product poisons could be measured. Experiments were carried out on rhodium, an important fission product poison. The fuel and assembly hardware for the BUCCX remains at Sandia and is available for future experimentation. The critical experiment currently in operation at the SPRF is the Seven Percent Critical Experiment (7uPCX). This experiment is designed to provide benchmark

Results of the critical experiments concerning OTTO loading at the critical HTR-test facility KAHTER

International Nuclear Information System (INIS)

Drueke, V.; Litzow, W.; Paul, N.

1982-12-01

Critical experiments concerning OTTO loading are described. In the KAHTER facility an OTTO loading has been simulated, therefore the original KAHTER assembly was reconstructed. The determination of critical masses and reactivity worths of control rods and of additional absorber rods in the top reflector and in the upper cavity was of main interest for comparison with reactor following calculations. Besides this, reaction rates in different energy regions were measured in the upper part of the core, in the cavity and top reflector. (orig.) [de

Temperature variation of criticality of thermal reactor lattices

International Nuclear Information System (INIS)

Velner, S.; Rothenstein, W.

1975-01-01

Departures from the asymptotic mode in the experimental setup have been examined in detail for two assemblies, one exponential, the other critical. It was found that the flux shape differed noticeably from the asymptotic mode in the core region especially for the exponential assemblies. On the other hand the departure from the fundamental mode has very little effect on the change of material buckling with temperature. Results of the calculations and their comparison with experiment are presented. The variation of material buckling with temperature is the same for ENDF/B-II and for ENDF/B-IV data, both for asymptotic reactor theory and for the buckling values derived from the flux calculated with the SN code. The results obtained with ENDF/B-IV data for both lattices are shown. In the small exponential assembly the results derived from S-4 calculations are compared with experiment. In the critical assembly the ratio of U-238 to U-235 fissions delta 28 and the relative conversion ratio - the ratio of U-238 captures to U-235 fissions in the lattice compared with the same quantity in a thermal column - are also shown. In both cases the experimental change of buckling with temperature is smaller than the calculated change. (B.G.)

A spent fuel assemblies monitoring device by nondestructive analysis 'PYTHON'

International Nuclear Information System (INIS)

Saad, M.; Broeskamp, M.; Hahn, H.; Bignan, G.; Boisset, M.; Silie, P.

1995-01-01

The monitoring of spent fuel assemblies (16 x 16 UOX) in KWG-reactor pool with the use of non-destructive methods (total Gamma and neutron counting) allow the control of average burn-up and the extremity burn-up. The measurements allow a safety-criticality control before loading the fuel assemblies into the transport casks. A device called PYTHON has been tested and qualified in France. This paper presents a description of the industrial PYTHON device and the results of the measurements. (orig.)

EXPERIMENTAL ANALYSES OF SPALLATION NEUTRONS GENERATED BY 100 MEV PROTONS AT THE KYOTO UNIVERSITY CRITICAL ASSEMBLY

Directory of Open Access Journals (Sweden)

CHEOL HO PYEON

2013-02-01

Full Text Available Neutron spectrum analyses of spallation neutrons are conducted in the accelerator-driven system (ADS facility at the Kyoto University Critical Assembly (KUCA. High-energy protons (100 MeV obtained from the fixed field alternating gradient accelerator are injected onto a tungsten target, whereby the spallation neutrons are generated. For neutronic characteristics of spallation neutrons, the reaction rates and the continuous energy distribution of spallation neutrons are measured by the foil activation method and by an organic liquid scintillator, respectively. Numerical calculations are executed by MCNPX with JENDL/HE-2007 and ENDF/B-VI libraries to evaluate the reaction rates of activation foils (bismuth and indium set at the target and the continuous energy distribution of spallation neutrons set in front of the target. For the reaction rates by the foil activation method, the C/E values between the experiments and the calculations are found around a relative difference of 10%, except for some reactions. For continuous energy distribution by the organic liquid scintillator, the spallation neutrons are observed up to 45 MeV. From these results, the neutron spectrum information on the spallation neutrons generated at the target are attained successfully in injecting 100 MeV protons onto the tungsten target.

Control and interpretation of criticality experiments on metallic assemblies

International Nuclear Information System (INIS)

Long, J.J.

1984-01-01

This paper deals with the principle of criticality experiment control with approach machines; to follow the reactivity evolution, one uses the classical method of the inverses of counting rates, then one shows how it is possible to extrapolate the approach curves that have been obtained [fr

DOE/NNSA introduction

International Nuclear Information System (INIS)

Black, S.

2005-01-01

The evolving threat of international terrorism and nuclear proliferation has manifested itself in a very compelling way in recent years. That' is why it is so important that experts continue to work together to minimize and eventually eliminate the use of HEU in civil nuclear applications, throughout the world, and as soon as possible. The most common civil use of HEU is in research and test reactors, either as fuel or targets. About 150 such reactors currently use HEU fuels. Research reactors and the use of uranium as targets in reactors play indispensable roles in the production of medical radioisotopes, radiation therapy, nuclear training, material testing, and scientific research. However, in nearly all cases, these missions can be accomplished without significant penalties using low enriched uranium fuels and targets, which would avoid the proliferation risk associated with HEU. To date, the RERTR program has made possible the partial or full conversion to LEU fuel of 39 reactors in 22 countries - reducing civil commerce in HEU by about 4 metric tons, sufficient material to manufacture over 100 nuclear weapons. In addition, since the start of the RERTR program in 1978, 21 research reactors in 16 countries have been built using an LEU fuel. This trend indicates that we are having an effect, that we are changing the way people think about research reactors. The focus for new construction is almost exclusively on LEU designs using fuels developed by the RERTR program. This has been a very interesting year for the RERTR program in terms of milestones and, regrettably, setbacks. Some serious fuel performance problems were encountered with the uranium-molybdenum dispersion fuel this year. On a more positive note, however, we had a major nonproliferation breakthrough with Libya and are now cooperating with Libyan experts to convert their research reactor and critical assembly to LEU fuel. As the global proliferation threat continues to evolve, we need a more

Block copolymer self-assembly-directed synthesis of mesoporous gyroidal superconductors.

Science.gov (United States)

Robbins, Spencer W; Beaucage, Peter A; Sai, Hiroaki; Tan, Kwan Wee; Werner, Jörg G; Sethna, James P; DiSalvo, Francis J; Gruner, Sol M; Van Dover, Robert B; Wiesner, Ulrich

2016-01-01

Superconductors with periodically ordered mesoporous structures are expected to have properties very different from those of their bulk counterparts. Systematic studies of such phenomena to date are sparse, however, because of a lack of versatile synthetic approaches to such materials. We demonstrate the formation of three-dimensionally continuous gyroidal mesoporous niobium nitride (NbN) superconductors from chiral ABC triblock terpolymer self-assembly-directed sol-gel-derived niobium oxide with subsequent thermal processing in air and ammonia gas. Superconducting materials exhibit a critical temperature (T c) of about 7 to 8 K, a flux exclusion of about 5% compared to a dense NbN solid, and an estimated critical current density (J c) of 440 A cm(-2) at 100 Oe and 2.5 K. We expect block copolymer self-assembly-directed mesoporous superconductors to provide interesting subjects for mesostructure-superconductivity correlation studies.

Critical experiments supporting close proximity water storage of power reactor fuel. Technical progress report

International Nuclear Information System (INIS)

Baldwin, M.N.; Hoovler, G.S.; Eng, R.L.; Welfare, F.G.

1979-07-01

Close-packed storage of LWR fuel assemblies is needed in order to expand the capacity of existing underwater storage pools. This increased capacity is required to accommodate the large volume of spent fuel produced by prolonged onsite storage. To provide benchmark criticality data in support of this effort, 20 critical assemblies were constructed that simulated a variety of close-packed LWR fuel storage configurations. Criticality calculations using the Monte Carlo KENO-IV code were performed to provide an analytical basis for comparison with the experimental data. Each critical configuration is documented in sufficient detail to permit the use of these data in validating calculational methods according to ANSI Standard N16.9-1975

Highly Enriched Uranium Metal Annuli and Cylinders with Polyethylene Reflectors and/or Internal Polyethylene Moderator

International Nuclear Information System (INIS)

Tyler Sumner; J. Blair Briggs; Leland Montierth

2007-01-01

A variety of critical experiments were constructed of enriched uranium metal during the 1960s and 1970s at the Oak Ridge Critical Experiments Facility in support of criticality safety operations at the Y-12 Plant. The purposes of these experiments included the evaluation of storage, casting, and handling limits for the Y-12 Plant and providing data for verification of calculation methods and cross-sections for nuclear criticality safety applications. These included solid cylinders of various diameters, annuli of various inner and outer diameters, two and three interacting cylinders of various diameters, and graphite and polyethylene reflected cylinders and annuli. Of the hundreds of delayed critical experiments, experiments of uranium metal annuli with and without polyethylene reflectors and with the central void region either empty or filled with polyethylene were evaluated under ICSBEP Identifier HEU-MET-FAST-076. The outer diameter of the uranium annuli varied from 9 to 15 inches in two-inch increments. In addition, there were uranium metal cylinders with diameters varying from 7 to 15 inches with complete reflection and reflection on one flat surface to simulate floor reflection. Most of the experiments were performed between February 1964 and April 1964. Five partially reflected (reflected on the top only) experiments were assembled in November 1967, but are judged by the evaluators not to be of benchmark quality. Twenty-four of the twenty-five experiments have been determined to have fast spectra. The only exception has a mixed spectrum. Analyses were performed in which uncertainty associated with five different parameters associated with the uranium parts and three associated with the polyethylene parts was evaluated. Included were uranium mass, height, diameter, isotopic content, and impurity content and polyethylene mass, diameter, and impurity content. There were additional uncertainties associated with assembly alignment, support structure, and the value

IRT - Sofia conversion feasibility study experience 2002-2009

Energy Technology Data Exchange (ETDEWEB)

Belousov, S.I.; Apostolov, T.G. [Institute for Nuclear Research and Nuclear Energy of Bulgarian Academy of Science, Tsarigradsko 72, 1784 Sofia (Bulgaria)

2010-07-01

A joint conversion feasibility study concerning the IRT - Sofia research reactor between INRNE and the RERTR Program at ANL was initiated in 2002. The initial steps studies (up to 2006) were mainly focused on neutronics properties significant for reactor application and safety analyses. Thermal hydraulic, accident analyses as well as additional neutronics study required were performed after that (up to 2010). The obtained results show that the IRT-4M LEU fuel assemblies (19.75% {sup 235}U enrichment) are appropriate for IRT-Sofia conversion (IRT-Sofia was initially designed for the IRT-2M HEU fuel assemblies with 36% {sup 235}U enrichment). The results obtained in the frames of the joint study show that the IRT-Sofia operation even with usage of only one pump in the primary circuit meets all safety requirements at power level up to 1000 kW and that safety is maintained for accident transients. Presented results of analyses (neutronics, thermal hydraulic, and accident) and accumulated experience for the IRT-Sofia will be useful for other research reactors where conversion from IRT-2M (HEU) to IRT-4M (LEU) fuel is underway and/or foreseen. (authors)

Cadmium verification measurements of HFIR shroud assembly 22

International Nuclear Information System (INIS)

Chapman, J.A.; Schultz, F.J.

1994-04-01

This report discusses radiation-based nondestructive examination methods which have been used to successfully verify the presence of cadmium in High Flux Isotope Reactor (HFIR) spent-fuel shroud assembly number 22 (SA22). These measurements show, in part, that SA22 is certified to meet the criticality safety specifications for a proposed reconfiguration of the HFIR spent-fuel storage array. Measurement of the unique 558.6-keV gamma-ray from neutron radiative capture on cadmium provided conclusive evidence for the presence of cadmium in the outer shroud of the assembly. Cadmium verification in the center post and outer shroud was performed by measuring the degree of neutron transmission in SA22 relative to two calibration shroud assemblies. Each measurement was performed at a single location on the center post and outer shroud. These measurements do not provide information on the spatial distribution or uniformity of cadmium within an assembly. Separate measurements using analog and digital radiography were performed to (a) globally map the continuity of cadmium internal mass, and (b) locally determine the thickness of cadmium. Radiography results will be reported elsewhere. The measurements reported here should not be used to infer the thickness of cadmium in either the center post or outer shroud of an assembly

Examination of Successful Modal Analysis Techniques Used for Bladed-Disk Assemblies

National Research Council Canada - National Science Library

Orsagh, R

2002-01-01

Modal testing of bladed-disk assemblies in turbomachines is used to identify the critical natural frequencies and mode shape information used for avoiding the per-rev resonant conditions that cause high cycle fatigue (HCF...

Feasibility study on heterogeneous method in criticality calculations

International Nuclear Information System (INIS)

Prati, A.

1977-01-01

The criticality of finite heterogeneous assemblies is analysed by the heterogeneous methods employing the Eigen-function analysis. The moderation is treated by the Fermi age theory. The system is analysed in two dimensional rectangular coordinates. The criticality and the fluxes are determined for systems with small and large number of fuel rods. The convergence and the residual error in the modal analysis are discussed. (author)

Critical experiments at Sandia National Laboratories

International Nuclear Information System (INIS)

Harms, G.A.; Ford, J.T.; Barber, A.D.

2011-01-01

Sandia National Laboratories (SNL) has conducted radiation effects testing for the Department of Energy (DOE) and other contractors supporting the DOE since the 1960's. Over this period, the research reactor facilities at Sandia have had a primary mission to provide appropriate nuclear radiation environments for radiation testing and qualification of electronic components and other devices. The current generation of reactors includes the Annular Core Research Reactor (ACRR), a water-moderated pool-type reactor, fueled by elements constructed from UO2-BeO ceramic fuel pellets, and the Sandia Pulse Reactor III (SPR-III), a bare metal fast burst reactor utilizing a uranium-molybdenum alloy fuel. The SPR-III is currently defueled. The SPR Facility (SPRF) has hosted a series of critical experiments. A purpose-built critical experiment was first operated at the SPRF in the late 1980's. This experiment, called the Space Nuclear Thermal Propulsion Critical Experiment (CX), was designed to explore the reactor physics of a nuclear thermal rocket motor. This experiment was fueled with highly-enriched uranium carbide fuel in annular water-moderated fuel elements. The experiment program was completed and the fuel for the experiment was moved off-site. A second critical experiment, the Burnup Credit Critical Experiment (BUCCX) was operated at Sandia in 2002. The critical assembly for this experiment was based on the assembly used in the CX modified to accommodate low-enriched pin-type fuel in water moderator. This experiment was designed as a platform in which the reactivity effects of specific fission product poisons could be measured. Experiments were carried out on rhodium, an important fission product poison. The fuel and assembly hardware for the BUCCX remains at Sandia and is available for future experimentation. The critical experiment currently in operation at the SPRF is the Seven Percent Critical Experiment (7uPCX). This experiment is designed to provide benchmark

Critical experiments at Sandia National Laboratories

Energy Technology Data Exchange (ETDEWEB)

Harms, G.A.; Ford, J.T.; Barber, A.D., E-mail: gaharms@sandia.gov [Sandia National Laboratories, Albuquerque, NM (United States)

2011-07-01

Sandia National Laboratories (SNL) has conducted radiation effects testing for the Department of Energy (DOE) and other contractors supporting the DOE since the 1960's. Over this period, the research reactor facilities at Sandia have had a primary mission to provide appropriate nuclear radiation environments for radiation testing and qualification of electronic components and other devices. The current generation of reactors includes the Annular Core Research Reactor (ACRR), a water-moderated pool-type reactor, fueled by elements constructed from UO2-BeO ceramic fuel pellets, and the Sandia Pulse Reactor III (SPR-III), a bare metal fast burst reactor utilizing a uranium-molybdenum alloy fuel. The SPR-III is currently defueled. The SPR Facility (SPRF) has hosted a series of critical experiments. A purpose-built critical experiment was first operated at the SPRF in the late 1980's. This experiment, called the Space Nuclear Thermal Propulsion Critical Experiment (CX), was designed to explore the reactor physics of a nuclear thermal rocket motor. This experiment was fueled with highly-enriched uranium carbide fuel in annular water-moderated fuel elements. The experiment program was completed and the fuel for the experiment was moved off-site. A second critical experiment, the Burnup Credit Critical Experiment (BUCCX) was operated at Sandia in 2002. The critical assembly for this experiment was based on the assembly used in the CX modified to accommodate low-enriched pin-type fuel in water moderator. This experiment was designed as a platform in which the reactivity effects of specific fission product poisons could be measured. Experiments were carried out on rhodium, an important fission product poison. The fuel and assembly hardware for the BUCCX remains at Sandia and is available for future experimentation. The critical experiment currently in operation at the SPRF is the Seven Percent Critical Experiment (7uPCX). This experiment is designed to provide

Experimental study of flow induced vibration of the planar fuel assembly

International Nuclear Information System (INIS)

Wang Jinhua; Bo Hanliang; Jiang Shengyao; Jia Haijun; Zheng Wenxiang; Min Gang; Qu Xinxing

2005-01-01

The paper studied the flow-induced vibration of the planar fuel assembly under scour of coolant through experiments, the study includes: the characteristics of the inherent vibration, the response to the flow-induced vibration in rating condition and the confirmation of the critical flow velocity's scope of the flow flexible instability. The velocity distributions in different flow channels formed by fuel plates in the assembly were measured, and the velocity distribution in the same flow channel was also measured. The experimental conclusions includes: the inherent vibration frequency of the planar fuel assembly is different for a little in each direction. The damp ratio corresponding to the assembly each rank's inherent frequency is small, and the damp ratio decreased with the increase of the corresponding inherent frequency. The velocity in different flow channels decreased from outside to inside, and the velocity in the middle channel was the least; the velocity in the same channel decreased from inside to outside, and the velocity in the middle position was the most. The vibration swing of the fuel assembly was small at rating condition, and the vibration swing of the fuel plates was larger than side plates. The vibration of the fuel assembly increased with the increase of the velocity, the vibration of the middle fuel plate were larger than the border fuel plate, and the vibration of the border fuel plate was larger than the side plate. The large scale vibration of the flow flexible instability didn't occur in the velocity scope of 0-18.8 m/s in the experiment, so the critical flow velocity of the flow flexible instability was not in the flow velocity scope of the experiment. (authors)

Conceptual design of a digital control system for nuclear criticality experiments

International Nuclear Information System (INIS)

Rojas, S.P.

1994-04-01

Nuclear criticality is a concern in many areas of nuclear engineering including waste management, nuclear weapons testing and design, basic nuclear research, and nuclear reactor design and analysis. As in many areas of science and engineering, experimental work conducted in this field has provided a wealth of data and insight essential to the formulation of theory and the advancement in knowledge of fissioning systems. In light of the many diverse applications of nuclear criticality, there is a continuing interest to learn and understand more about the fundamental physical processes through continued experimentation. This thesis addresses the problem of setting up and programming a microprocessor-based digital control system (PLC) for a proposed critical experiment using, among other devices, a stepper motor, a joystick control mechanism, and switches. This experiment represents a revised configuration to test cylindrical nuclear waste packages. A Monte Carlo numerical study for the proposed critical assembly has been performed in order to illustrate how results from numerical calculations are used in the process of assembling the control system and to corroborate previous experimental data. In summary, a control system utilizing some common devices necessary to perform a critical experiment (stepper motor, push-buttons, etc.) has been assembled. Control components were sized using the results of a probabilistic computer code (MCNP). Finally, a program was written that illustrates the coupling between the hardware and the devices being controlled in the new test fixture

The ORR Whole-Core LEU Fuel Demonstration

International Nuclear Information System (INIS)

Bretscher, M.M.; Snelgrove, J.L.

1990-01-01

The ORR Whole-Core LEU Fuel Demonstration, conducted as part of the US Reduced Enrichment Research and Test Reactor Program, has been successfully completed. Using commercially-fabricated U 3 Si 2 -Al 20%-enriched fuel elements (4.8 g U/cc) and fuel followers (3.5 g U/cc), the 30-MW Oak Ridge Research Reactor was safely converted from an all-HEU core, through a series of HEU/LEU mixed transition cores, to an all-LEU core. There were no fuel element failures and average discharge burnups were measured to be as high as 50% for the standard elements and 75% for the fuel followers. Experimental results for burnup-dependent critical configurations, cycle-averaged fuel element powers, and fuel-element-averaged 235 U burnups validated predictions based on three-dimensional depletion calculations. Calculated values for plutonium production and isotopic mass ratios as functions of 235 U burnup support the corresponding measured quantities. In general, calculations for reaction rate distributions, control rod worths, prompt neutron decay constants, and isothermal temperature coefficients were found to agree with corresponding measured values. Experimentally determined critical configurations for fresh HEU and LEU cores radially reflected with water and with beryllium are well-predicted by both Monte Carlo and diffusion calculations. 17 refs

Subcritical Multiplication Parameters of the Accelerator-Driven System with 100 MeV Protons at the Kyoto University Critical Assembly

Directory of Open Access Journals (Sweden)

Jae-Yong Lim

2012-01-01

Full Text Available Basic experiments on the accelerator-driven system (ADS at the Kyoto University Critical Assembly are carried out by combining a solid-moderated and -reflected core with the fixed-field alternating gradient accelerator. The reaction rates are measured by the foil activation method to obtain the subcritical multiplication parameters. The numerical calculations are conducted with the use of MCNPX and JENDL/HE-2007 to evaluate the reaction rates of activation foils set in the core region and at the location of the target. Here, a comparison between the measured and calculated eigenvalues reveals a relative difference of around 10% in C/E values. A special mention is made of the fact that the reaction rate analyses in the subcritical systems demonstrate apparently the actual effect of moving the tungsten target into the core on neutron multiplication. A series of further ADS experiments with 100 MeV protons needs to be carried out to evaluate the accuracy of subcritical multiplication parameters.

Criticality experiments with low enriched UO2 fuel rods in water containing dissolved gadolinium

International Nuclear Information System (INIS)

Bierman, S.R.; Murphy, E.S.; Clayton, E.D.; Keay, R.T.

1984-02-01

The results obtained in a criticality experiments program performed for British Nuclear Fuels, Ltd. (BNFL) under contract with the United States Department of Energy (USDOE) are presented in this report along with a complete description of the experiments. The experiments involved low enriched UO 2 and PuO 2 -UO 2 fuel rods in water containing dissolved gadolinium, and are in direct support of BNFL plans to use soluble compounds of the neutron poison gadolinium as a primary criticality safeguard in the reprocessing of low enriched nuclear fuels. The experiments were designed primarily to provide data for validating a calculation method being developed for BNFL design and safety assessments, and to obtain data for the use of gadolinium as a neutron poison in nuclear chemical plant operations - particularly fuel dissolution. The experiments program covers a wide range of neutron moderation (near optimum to very under-moderated) and a wide range of gadolinium concentration (zero to about 2.5 g Gd/l). The measurements provide critical and subcritical k/sub eff/ data (1 greater than or equal to k/sub eff/ greater than or equal to 0.87) on fuel-water assemblies of UO 2 rods at two enrichments (2.35 wt % and 4.31 wt % 235 U) and on mixed fuel-water assemblies of UO 2 and PuO 2 -UO 2 rods containing 4.31 wt % 235 U and 2 wt % PuO 2 in natural UO 2 respectively. Critical size of the lattices was determined with water containing no gadolinium and with water containing dissolved gadolinium nitrate. Pulsed neutron source measurements were performed to determine subcritical k/sub eff/ values as additional amounts of gadolinium were successively dissolved in the water of each critical assembly. Fission rate measurements in 235 U using solid state track recorders were made in each of the three unpoisoned critical assemblies, and in the near-optimum moderated and the close-packed poisoned assemblies of this fuel

Fast assembly of ordered block copolymer nanostructures through microwave annealing.

Science.gov (United States)

Zhang, Xiaojiang; Harris, Kenneth D; Wu, Nathanael L Y; Murphy, Jeffrey N; Buriak, Jillian M

2010-11-23

Block copolymer self-assembly is an innovative technology capable of patterning technologically relevant substrates with nanoscale precision for a range of applications from integrated circuit fabrication to tissue interfacing, for example. In this article, we demonstrate a microwave-based method of rapidly inducing order in block copolymer structures. The technique involves the usage of a commercial microwave reactor to anneal block copolymer films in the presence of appropriate solvents, and we explore the effect of various parameters over the polymer assembly speed and defect density. The approach is applied to the commonly used poly(styrene)-b-poly(methyl methacrylate) (PS-b-PMMA) and poly(styrene)-b-poly(2-vinylpyridine) (PS-b-P2VP) families of block copolymers, and it is found that the substrate resistivity, solvent environment, and anneal temperature all critically influence the self-assembly process. For selected systems, highly ordered patterns were achieved in less than 3 min. In addition, we establish the compatibility of the technique with directed assembly by graphoepitaxy.

Critical experiments analysis by ABBN-90 constant system

Energy Technology Data Exchange (ETDEWEB)

Tsiboulia, A.; Nikolaev, M.N.; Golubev, V. [Institute of Physics and Power Engineering, Obninsk (Russian Federation)] [and others

1997-06-01

The ABBN-90 is a new version of the well-known Russian group-constant system ABBN. Included constants were calculated based on files of evaluated nuclear data from the BROND-2, ENDF/B-VI, and JENDL-3 libraries. The ABBN-90 is intended for the calculation of different types of nuclear reactors and radiation shielding. Calculations of criticality safety and reactivity accidents are also provided by using this constant set. Validation of the ABBN-90 set was made by using a computerized bank of evaluated critical experiments. This bank includes the results of experiments conducted in Russia and abroad of compact spherical assemblies with different reflectors, fast critical assemblies, and fuel/water-solution criticalities. This report presents the results of the calculational analysis of the whole collection of critical experiments. All calculations were produced with the ABBN-90 group-constant system. Revealed discrepancies between experimental and calculational results and their possible reasons are discussed. The codes and archives INDECS system is also described. This system includes three computerized banks: LEMEX, which consists of evaluated experiments and their calculational results; LSENS, which consists of sensitivity coefficients; and LUND, which consists of group-constant covariance matrices. The INDECS system permits us to estimate the accuracy of neutronics calculations. A discussion of the reliability of such estimations is finally presented. 16 figs.

Compendium on neutron spectra in criticality accident dosimetry

International Nuclear Information System (INIS)

Ing, H.

1978-01-01

Graphical and tabulated neutron spectra are presented: from selected critical assemblies; from critical solutions; of fission neutrons through shielding; of H 2 O-moderated fission neutrons through shielding; of D 2 O-moderated fission neutrons through shielding; of fission neutrons reflected from various materials; from the D(T, 4 He)n reaction (''14 MeV'' neutrons) through shielding and of ''14 MeV'' neutrons reflected from various materials

Performance of PARR-1 with LEU Fuel

International Nuclear Information System (INIS)

Pervez, S.; Latif, M.; Bokhari, I.H.; Bakhtyar, S.

2005-01-01

Pakistan Research Reactor (PARR-1) went critical in 1965 with HEU fuel. The reactor core was converted to LEU fuel with power upgradation from 5 MW to 10 MW in 1992. The reactor has been operated with LEU fuel for about 10,000 hours and has produced about 66,000 MWh energy up to now. Average burn up of the irradiated fuel is about 42 %. The fuel performance during the last 12 years has been excellent. Post irradiation visual inspection of the fuel has revealed no abnormality. During operation there have been no signs of releases in the pool water establishing the full integrity of this fuel. The reactor has been mainly utilized for radioisotope production, beam tube experiments including neutron diffraction studies, neutron radiography etc. Studies have been completed to operate the reactor with a mixed core (HEU + LEU) to utilize the less burned HEU fuel elements. A major project of production of fission Moly using PARR-1 is in the final stages. (author)

Regulation of corneal stroma extracellular matrix assembly.

Science.gov (United States)

Chen, Shoujun; Mienaltowski, Michael J; Birk, David E

2015-04-01