High temperature shock tube experiments and kinetic modeling study of diisopropyl ketone ignition and pyrolysis

KAUST Repository

Barari, Ghazal

2017-03-10

Diisopropyl ketone (DIPK) is a promising biofuel candidate, which is produced using endophytic fungal conversion. In this work, a high temperature detailed combustion kinetic model for DIPK was developed using the reaction class approach. DIPK ignition and pyrolysis experiments were performed using the UCF shock tube. The shock tube oxidation experiments were conducted between 1093K and 1630K for different reactant compositions, equivalence ratios (φ=0.5–2.0), and pressures (1–6atm). In addition, methane concentration time-histories were measured during 2% DIPK pyrolysis in argon using cw laser absorption near 3400nm at temperatures between 1300 and 1400K near 1atm. To the best of our knowledge, current ignition delay times (above 1050K) and methane time histories are the first such experiments performed in DIPK at high temperatures. Present data were used as validation targets for the new kinetic model and simulation results showed fair agreement compared to the experiments. The reaction rates corresponding to the main consumption pathways of DIPK were found to have high sensitivity in controlling the reactivity, so these were adjusted to attain better agreement between the simulation and experimental data. A correlation was developed based on the experimental data to predict the ignition delay times using the temperature, pressure, fuel concentration and oxygen concentration.

Morphological characteristics of waste polyethylene/polypropylene plastics during pyrolysis and representative morphological signal characterizing pyrolysis stages.

Science.gov (United States)

Wang, H; Chen, D; Yuan, G; Ma, X; Dai, X

2013-02-01

In this work, the morphological characteristics of waste polyethylene (PE)/polypropylene (PP) plastics during their pyrolysis process were investigated, and based on their basic image changing patterns representative morphological signals describing the pyrolysis stages were obtained. PE and PP granules and films were used as typical plastics for testing, and influence of impurities was also investigated. During pyrolysis experiments, photographs of the testing samples were taken sequentially with a high-speed infrared camera, and the quantitative parameters that describe the morphological characteristics of these photographs were explored using the "Image Pro Plus (v6.3)" digital image processing software. The experimental results showed that plastics pyrolysis involved four stages: melting, two stages of decomposition which are characterized with bubble formation caused by volatile evaporating, and ash deposition; and each stage was characterized with its own phase changing behaviors and morphological features. Two stages of decomposition are the key step of pyrolysis since they took up half or more of the reaction time; melting step consumed another half of reaction time in experiments when raw materials were heated up from ambient temperatures; and coke-like deposition appeared as a result of decomposition completion. Two morphological signals defined from digital image processing, namely, pixel area of the interested reaction region and bubble ratio (BR) caused by volatile evaporating were found to change regularly with pyrolysis stages. In particular, for all experimental scenarios with plastics films and granules, the BR curves always exhibited a slowly drop as melting started and then a sharp increase followed by a deep decrease corresponding to the first stage of intense decomposition, afterwards a second increase - drop section corresponding to the second stage of decomposition appeared. As ash deposition happened, the BR dropped to zero or very low

Volume reduction of ion exchange resin by a pyrolysis technique

International Nuclear Information System (INIS)

Matsuda, M.; Funabashi, K.; Uchida, S.; Kikuchi, M.

1985-01-01

Volume reduction techniques, such as incineration and acid digestion, of spent ion exchange resins from nuclear power plants are being developed with a view toward reducing radioactive waste volume and also making the final waste form more stable. The authors chose pyrolysis as a technique that can be done at low operating temperatures and low gas flow rates in a reactor vessel. Fundamental experiments were performed to clarify the resin pyrolysis characteristics, and the optimum pyrolysis temperature was determined. Consequently, a pilot plant with a treatment capacity of approx. 50 kg/batch was constructed based on the results. Using the pilot plant, the authors are now performing pyrolysis of the resins and solidification of their residues. This report will give the results of fundamental experiments and pilot plant tests

Thermogravimetric kinetic study of agricultural residue biomass pyrolysis based on combined kinetics.

Science.gov (United States)

Wang, Xun; Hu, Mian; Hu, Wanyong; Chen, Zhihua; Liu, Shiming; Hu, Zhiquan; Xiao, Bo

2016-11-01

Pyrolytic kinetic of an agricultural residue (AR) feedstock, a mixture of plants (cotton, wheat, rich, corn) stems, was investigated based on combined kinetics. The most suitable mechanism for AR one-step pyrolysis was f(α)=(1-α)(1.1816)α(-1.8428) with kinetic parameters of: apparent activation energy 221.7kJ/mol, pre-exponential factor 4.17E16s(-1). Pyrolysis of AR feedstock could not be described by one-step reaction attributes to heterogeneous features of pyrolysis processes. Combined kinetics three-parallel-reaction (CK-TPR) model fitted the pyrolysis experimental data very well. Reaction mechanisms for pseudo hemicelluloses, cellulose, lignin in CK-TPR model was f(α)=(1-α)(1.6244)α(-0.3371)[-ln(1-α)](-0.0515), f(α)=(1-α)(1.0597)α(-0.6909)[-ln(1-α)](0.9026) and f(α)=(1-α)(2.9577)α(-4.7719), respectively. Apparent activation energy of three pseudo components followed the order of Elignin(197.3kJ/mol)>Ecellulose(176.3kJ/mol)>Ehemicelluloses (151.1kJ/mol). Mechanism of hemicelluloses pyrolysis could be further expressed as f(α)=(1-α)(1.4). The pyrolytic mechanism of cellulose met the Nucleation well. However, mechanism of lignin pyrolysis was complex, which possibly was the combined effects of Nucleation, Diffusion, Geometrical contraction, and Power law. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolysis and gasification behavior of black liquor under pressurized conditions

Energy Technology Data Exchange (ETDEWEB)

Whitty, K

1997-11-01

The purpose of this study has been to enhance the understanding of the processes involved in pressurized black liquor gasification. Gasification is known to occur in three stages: drying, pyrolysis and char gasification. The work presented here focuses on the pyrolysis and gasification stages. Experiments were carried out primarily in two laboratory-scale reactors. A pressurized grid heater was used to study black liquor pyrolysis under pressurized conditions. Char yields and the fate of elements in the liquor, as well as the degree of liquor swelling, were measured in this device. A pressurized thermogravimetric reactor was used to measure the rate of the char gasification process under different temperatures and pressures and in various gas atmospheres. Pyrolysis experiments were also carried out in this device, and data on swelling behavior, char yields and component release were obtained 317 refs.

Conventional and microwave pyrolysis of a macroalgae waste from the Agar-Agar industry. Prospects for bio-fuel production.

Science.gov (United States)

Ferrera-Lorenzo, N; Fuente, E; Bermúdez, J M; Suárez-Ruiz, I; Ruiz, B

2014-01-01

A comparative study of the pyrolysis of a macroalgae industrial solid waste (algae meal) in an electrical conventional furnace and in a microwave furnace has been carried out. It was found that the chars obtained from both pyrolyses are similar and show good properties for performing as a solid bio-fuel and as a precursor of activated carbon. Bio-oils from conventional pyrolysis have a greater number of phenolic, pyrrole and alkane compounds whereas benzene and pyridine compounds are more predominant in microwave pyrolysis with a major presence of light compounds. The bio-gas fraction from microwave pyrolysis presents a much higher syngas content (H2+CO), and a lower CO2 and CH4 proportion than that obtained by conventional pyrolysis. Yields are similar for both treatments with a slightly higher gas yield in the case of microwave pyrolysis due to the fact that microwave heating favors heterogeneous reactions between the gases and the char. Copyright © 2013 Elsevier Ltd. All rights reserved.

Fast pyrolysis of linseed. Product yields and compositions

Energy Technology Data Exchange (ETDEWEB)

Acikgoz, C.; Onay, O.; Kockar, O.M. [Department of Chemical Engineering, Faculty of Engineering and Architecture, Iki Eylul Campus, Anadolu University, Eskisehir 26470 (Turkey)

2004-06-01

Fixed-bed fast pyrolysis experiments have been conducted on a sample of linseed (Linum usitatissimum L.) to determine particularly the effect of pyrolysis temperature, heating rate, particle size and sweep gas flow rate on the pyrolysis product yields and their compositions. The maximum oil yield of 57.7wt.% was obtained at a final pyrolysis temperature of 550C, particle size range 0.6mmpyrolysis products were characterised by elemental analysis and various chromatographic and spectroscopic techniques. Chromatographic and spectroscopic studies on oil showed that it can be used as a renewable fuel and chemical feedstock, with a calorific value of 38.45MJ/kg and empirical formula of CH{sub 1.64}O{sub 0.11}N{sub 0.03}.

Scrap tire pyrolysis using a new type two-stage pyrolyzer: Effects of dolomite and olivine on producing a low-sulfur pyrolysis oil

International Nuclear Information System (INIS)

Choi, Gyung-Goo; Oh, Seung-Jin; Kim, Joo-Sik

2016-01-01

Scrap tire pyrolysis was performed using a two-stage pyrolyzer consisting of an auger reactor and a fluidized bed reactor to produce a low-sulfur pyrolysis oil. In the experiments, the effect of the residence time of the feed material in the auger reactor was investigated at ∼300 (auger reactor) and 500 °C (fluidized bed reactor). In addition, natural dolomite and olivine and calcined dolomite and olivine were used as the fluidized bed materials to examine their effects on reducing the sulfur content of pyrolysis oil. In the experiments, the yields of the oil from the auger reactor were 1.4–3.7 wt%, and it was enriched with DL-limonene whose content in the oil was 40–50 wt%. The yields of the oil from the fluidized bed reactor were 42–46 wt%. The optimum residence time of the feed material in the auger reactor turned out to be 3.5 min. Calcined dolomite and olivine significantly decreased the sulfur content of pyrolysis oil. Metal oxides of the additives appeared to react with H_2S to form metal sulfides. The sulfur content of pyrolysis oil obtained with calcined olivine was 0.45 wt%. - Highlights: • Scrap tires were successfully pyrolyzed in a new type two-stage pyrolyzer. • The two-stage pyrolyzer is composed of an auger and fluidized bed reactors. • Calcination of olivine and dolomite led to a strong decrease in sulfur. • The lowest sulfur content of pyrolysis oil was 0.45 wt%. • Pyrolysis oil yields from the fluidized bed reactor were 43–46 wt%.

Biobased alkylphenols from lignins via a two-step pyrolysis - Hydrodeoxygenation approach.

Science.gov (United States)

de Wild, P J; Huijgen, W J J; Kloekhorst, A; Chowdari, R K; Heeres, H J

2017-04-01

Five technical lignins (three organosolv, Kraft and soda lignin) were depolymerised to produce monomeric biobased aromatics, particularly alkylphenols, by a new two-stage thermochemical approach consisting of dedicated pyrolysis followed by catalytic hydrodeoxygenation (HDO) of the resulting pyrolysis oils. Pyrolysis yielded a mixture of guaiacols, catechols and, optionally, syringols in addition to alkylphenols. HDO with heterogeneous catalysts (Ru/C, CoMo/alumina, phosphided NiMO/C) effectively directed the product mixture towards alkylphenols by, among others, demethoxylation. Up to 15wt% monomeric aromatics of which 11wt% alkylphenols was obtained (on the lignin intake) with limited solid formation (<3wt% on lignin oil intake). For comparison, solid Kraft lignin was also directly hydrotreated for simultaneous depolymerisation and deoxygenation resulting in two times more alkylphenols. However, the alkylphenols concentration in the product oil is higher for the two-stage approach. Future research should compare direct hydrotreatment and the two-stage approach in more detail by techno-economic assessments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Extent of pyrolysis impacts on fast pyrolysis biochar properties.

Science.gov (United States)

Brewer, Catherine E; Hu, Yan-Yan; Schmidt-Rohr, Klaus; Loynachan, Thomas E; Laird, David A; Brown, Robert C

2012-01-01

A potential concern about the use of fast pyrolysis rather than slow pyrolysis biochars as soil amendments is that they may contain high levels of bioavailable C due to short particle residence times in the reactors, which could reduce the stability of biochar C and cause nutrient immobilization in soils. To investigate this concern, three corn ( L.) stover fast pyrolysis biochars prepared using different reactor conditions were chemically and physically characterized to determine their extent of pyrolysis. These biochars were also incubated in soil to assess their impact on soil CO emissions, nutrient availability, microorganism population growth, and water retention capacity. Elemental analysis and quantitative solid-state C nuclear magnetic resonance spectroscopy showed variation in O functional groups (associated primarily with carbohydrates) and aromatic C, which could be used to define extent of pyrolysis. A 24-wk incubation performed using a sandy soil amended with 0.5 wt% of corn stover biochar showed a small but significant decrease in soil CO emissions and a decrease in the bacteria:fungi ratios with extent of pyrolysis. Relative to the control soil, biochar-amended soils had small increases in CO emissions and extractable nutrients, but similar microorganism populations, extractable NO levels, and water retention capacities. Corn stover amendments, by contrast, significantly increased soil CO emissions and microbial populations, and reduced extractable NO. These results indicate that C in fast pyrolysis biochar is stable in soil environments and will not appreciably contribute to nutrient immobilization. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Highly time-resolved imaging of combustion and pyrolysis product concentrations in solid fuel combustion: NO formation in a burning cigarette.

Science.gov (United States)

Zimmermann, Ralf; Hertz-Schünemann, Romy; Ehlert, Sven; Liu, Chuan; McAdam, Kevin; Baker, Richard; Streibel, Thorsten

2015-02-03

The highly dynamic, heterogeneous combustion process within a burning cigarette was investigated by a miniaturized extractive sampling probe (microprobe) coupled to photoionization mass spectrometry using soft laser single photon ionization (SPI) for online real-time detection of molecular ions of combustion and pyrolysis products. Research cigarettes smoked by a smoking machine are used as a reproducible model system for solid-state biomass combustion, which up to now is not addressable by current combustion-diagnostic tools. By combining repetitively recorded online measurement sequences from different sampling locations in an imaging approach, highly time- and space-resolved quantitative distribution maps of, e.g., nitrogen monoxide, benzene, and oxygen concentrations were obtained at a near microscopic level. The obtained quantitative distribution maps represent a time-resolved, movie-like imaging of the respective compound's formation and destruction zones in the various combustion and pyrolysis regions of a cigarette during puffing. Furthermore, spatially resolved kinetic data were ascertainable. The here demonstrated methodology can also be applied to various heterogenic combustion/pyrolysis or reaction model systems, such as fossil- or biomass-fuel pellet combustion or to a positional resolved analysis of heterogenic catalytic reactions.

Pyrolysis process for the treatment of food waste.

Science.gov (United States)

Grycová, Barbora; Koutník, Ivan; Pryszcz, Adrian

2016-10-01

Different waste materials were pyrolysed in the laboratory pyrolysis unit to the final temperature of 800°C with a 10min delay at the final temperature. After the pyrolysis process a mass balance of the resulting products, off-line analysis of the pyrolysis gas and evaluation of solid and liquid products were carried out. The gas from the pyrolysis experiments was captured discontinuously into Tedlar gas sampling bags and the selected components were analyzed by gas chromatography (methane, ethene, ethane, propane, propene, hydrogen, carbon monoxide and carbon dioxide). The highest concentration of measured hydrogen (WaCe 61%vol.; WaPC 66%vol.) was analyzed at the temperature from 750 to 800°C. The heating values of the solid and liquid residues indicate the possibility of its further use for energy recovery. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study on the Inference Factors of Huangling Coking Coal Pyrolysis

Science.gov (United States)

Du, Meili; Yang, Zongyi; Fan, Jinwen

2018-01-01

In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

Cooperative and Heterogeneous Indoor Localization - Experiments

DEFF Research Database (Denmark)

Benoît, Denis; Raulefs, Ronald; Fleury, Bernard Henri

2013-01-01

In this paper we present the results of real-life localization experiments performed in an unprecedented cooperative and heterogeneous wireless context. These measurements are based on ZigBee and orthogonal frequency division multiplexing (OFDM) devices, respectively endowed with received signal...

Experimental study of rapid brown coal pyrolysis at high temperature

Energy Technology Data Exchange (ETDEWEB)

Qian, Lin; Sun, Shaozeng; Meng, Shun; Meng, Xianyu; Guo, Yangzhou [Harbin Institute of Technology, Harbin (China). Combustion Engineering Research Inst.

2013-07-01

Rapid coal pyrolysis is a very important step in the early stage of combustion. Rapid pyrolysis experiments of a brown coal at high temperature have been studied on a laminar drop tube furnace. The volatile mass release measured in this study is high for low rank coal. The activation energy and pre-exponential factor of pyrolysis are 19901.22 kJ/mol and 102.71, respectively. The nitrogen distribution between volatile and char is 0.54. With the increase of temperature, the yields of NH{sub 3} decreases, while those of HCN increases, leading the value of HCN/NH{sub 3} to become larger. At high temperature, the main nitrogen- containing species of pyrolysis in volatile is HCN.

Coal pyrolysis and char burnout under conventional and oxy-fuel conditions

Energy Technology Data Exchange (ETDEWEB)

Al-Makhadmeh, L.; Maier, J.; Scheffknecht, G. [Stuttgart Univ. (Germany). Institut fuer Verfahrenstechnik und Dampfkesselwesen

2009-07-01

Coal utilization processes such as combustion or gasification generally involve several steps i.e., the devolatilization of organic materials, homogeneous reactions of volatile matter with the reactant gases, and heterogeneous reactions of the solid (char) with the reactant gases. Most of the reported work about coal pyrolysis and char burnout were performed at low temperatures under environmental conditions related to the air firing process with single particle tests. In this work, coal combustion under oxy-fuel conditions is investigated by studying coal pyrolysis and char combustion separately in practical scales, with the emphasis on improving the understanding of the effect of a CO{sub 2}-rich gas environment on coal pyrolysis and char burnout. Two coals, Klein Kopje a medium volatile bituminous coal and a low-rank coal, Lausitz coal were used. Coal pyrolysis in CO{sub 2} and N{sub 2} environments were performed for both coals at different temperatures in an entrained flow reactor. Overall mass release, pyrolysis gas concentrations, and char characterization were performed. For char characterization ultimate analysis, particle size, and BET surface area were measured. Chars for both coals were collected at 1150 C in both CO{sub 2} and N{sub 2} environments. Char combustion was performed in a once-through 20 kW test facility in O{sub 2}/CO{sub 2} and O{sub 2}/N{sub 2} atmospheres. Besides coal quality, oxygen partial pressure was chosen as a variable to study the effect of the gas environment on char burnout. In general, it is found that the CO{sub 2} environment and coal rank have a significant effect on coal pyrolysis and char burnout. (orig.)

Modelling of biomass pyrolysis

International Nuclear Information System (INIS)

Kazakova, Nadezhda; Petkov, Venko; Mihailov, Emil

2015-01-01

Pyrolysis is an essential preliminary step in a gasifier. The first step in modelling the pyrolysis process of biomass is creating a model for the chemical processes taking place. This model should describe the used fuel, the reactions taking place and the products created in the process. The numerous different polymers present in the organic fraction of the fuel are generally divided in three main groups. So, the multistep kinetic model of biomass pyrolysis is based on conventional multistep devolatilization models of the three main biomass components - cellulose, hemicelluloses, and lignin. Numerical simulations have been conducted in order to estimate the influence of the heating rate and the temperature of pyrolysis on the content of the virgin biomass, active biomass, liquid, solid and gaseous phases at any moment. Keywords: kinetic models, pyrolysis, biomass pyrolysis.

Co-pyrolysis of lignite and sugar beet pulp

International Nuclear Information System (INIS)

Yilgin, M.; Deveci Duranay, N.; Pehlivan, D.

2010-01-01

Today, worldwide studies have been undertaken on the biomass usage and co-conversion of biomass and coal to seek out alternative fuels for supplying energy in an environmental friendly way. The objective of this work is to study co-pyrolysis of lignite and sugar beet pulp in 50/50 (wt./wt.) ratio of blend pellets, to elucidate their thermal behaviour under pyrolysis conditions and to assess major decomposition products in terms of their yields. A special chamber, which has enabled very fast heating rates, was used in the pyrolysis experiments carried at 600 deg. C. The results were interpreted in the light of liquid, solid and gaseous yields, resulting from thermal decomposition, and kinetics of thermogravimetric analysis. Proximate volatile matter and ash contents of the blends were different compared to those found by using individual values. Sugar beet pulp decomposed faster within a relatively narrow temperature range than lignite and underwent a significant shrinkage during pyrolysis. It was found that the chars left behind after the flash pyrolysis of these pellets at 600 deg. C have substantial amounts of volatile matter that would evolve upon further heating.

Evaluation of co-pyrolysis petrochemical wastewater sludge with lignite in a thermogravimetric analyzer and a packed-bed reactor: Pyrolysis characteristics, kinetics, and products analysis.

Science.gov (United States)

Mu, Lin; Chen, Jianbiao; Yao, Pikai; Zhou, Dapeng; Zhao, Liang; Yin, Hongchao

2016-12-01

Co-pyrolysis characteristics of petrochemical wastewater sludge and Huolinhe lignite were investigated using thermogravimetric analyzer and packed-bed reactor coupled with Fourier transform infrared spectrometer and gas chromatography. The pyrolysis characteristics of the blends at various sludge blending ratios were compared with those of the individual materials. Thermogravimetric experiments showed that the interactions between the blends were beneficial to generate more residues. In packed-bed reactor, synergetic effects promoted the release of gas products and left less liquid and solid products than those calculated by additive manner. Fourier transform infrared spectrometer analysis showed that main functional groups in chars gradually disappeared with pyrolysis temperatures increasing, and H 2 O, CH 4 , CO, and CO 2 appeared in volatiles during pyrolysis. Gas compositions analysis indicated that, the yields of H 2 and CO clearly increased as the pyrolysis temperature and sludge blending ratio increasing, while the changes of CH 4 and CO 2 yields were relatively complex. Copyright © 2016 Elsevier Ltd. All rights reserved.

Distribution of sulphur into products from waste tire pyrolysis

International Nuclear Information System (INIS)

Susa, D.; Haydary, J.; Markos, J.

2012-01-01

Tire pyrolysis is getting growing attention as an effective waste tire disposal method in comparison to environmentally less friendly methods like dumping or incineration. But the scrap tire sulphur content can be a potential obstacle to scrap tire utilization as a fuel. In this paper the distribution of sulphur into tire pyrolysis yields, solid (char) and liquid (tar), was investigated. The pyrolysis experiments were carried out under different conditions to determine the partitioning of sulphur into pyrolysis products. The influence of different temperatures and reaction times was investigated in a laboratory flow reactor under nitrogen atmosphere. Solid and liquid residues were collected and analyzed by elemental analysis. The sulphur content in residual char and tar was determined using an elemental analyzer and the sulphur forms in tar were characterized by the X-ray photoelectron spectroscopy (XPS). (Authors)

A pyrolysis study for the thermal and kinetic characteristics of an agricultural waste with two different plastic wastes.

Science.gov (United States)

Çepelioğullar, Özge; Pütün, Ayşe E

2014-10-01

In this study, thermochemical conversion of plastic wastes (PET and PVC) together with an agricultural waste (hazelnut shell) was investigated. In order to determine the thermal and kinetic behaviours, pyrolysis experiments were carried out from room temperature to 800 °C, with a heating rate of 10 °C min(-1) in the presence of a N2 atmosphere in a thermogravimetric analyzer. With the obtained thermogravimetric data, an appropriate temperature was specified for the pyrolysis of biomass-plastic wastes in a fixed-bed reactor. At the second step, pyrolysis experiments were carried out at the same conditions with the thermogravimetric analyzer, except the final temperature which was up to 500 °C in this case. After pyrolysis experiments, pyrolysis yields were calculated and characterization studies for bio-oil were investigated. Experimental results showed that co-pyrolysis has an important role in the determination of the pyrolysis mechanism and the process conditions while designing/implementing a thermochemical conversion method where biomass-plastic materials were preferred as raw materials. © The Author(s) 2014.

Catalytic Hydrotreatment of Fast Pyrolysis Oil : Model Studies on Reaction Pathways for the Carbohydrate Fraction

NARCIS (Netherlands)

Wildschut, J.; Arentz, J.; Rasrendra, C. B.; Venderbosch, R. H.; Heeres, H. J.

2009-01-01

Fast pyrolysis oil can be upgraded by a catalytic hydrotreatment (250-400 degrees C, 100-200 bar) using heterogeneous catalysts such as Ru/C to hydrocarbon-like products that can serve as liquid transportation fuels. Insight into the complex reaction pathways of the various component fractions

Internally Heated Screw Pyrolysis Reactor (IHSPR) heat transfer performance study

Science.gov (United States)

Teo, S. H.; Gan, H. L.; Alias, A.; Gan, L. M.

2018-04-01

1.5 billion end-of-life tyres (ELT) were discarded globally each year and pyrolysis is considered the best solution to convert the ELT into valuable high energy-density products. Among all pyrolysis technologies, screw reactor is favourable. However, conventional screw reactor risks plugging issue due to its lacklustre heat transfer performance. An internally heated screw pyrolysis reactor (IHSPR) was developed by local renewable energy industry, which serves as the research subject for heat transfer performance study of this particular paper. Zero-load heating test (ZLHT) was first carried out to obtain the operational parameters of the reactor, followed by the one dimensional steady-state heat transfer analysis carried out using SolidWorks Flow Simulation 2016. Experiments with feed rate manipulations and pyrolysis products analyses were conducted last to conclude the study.

Studies of pyrolysis kinetics of sewage sludge obtained from dynamic experiments; Estudio cinetico de la pirolisis de fangos mediante experimentos dinamicos

Energy Technology Data Exchange (ETDEWEB)

Arauzo, J; Gonzalo, A; Sanchez, J L [Universidad de Zaragoza, Madrid (Spain). Inst. de Investigacion en Ingenieria de Aragon. Grupo de Procesos Termoquimicos; Resende, F L.P. [University of Michigan, Ann Arbor, MI (United States). Dept. of Chemical Engineering; Rocha, J D [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico (NIPE); Mesa Perez, J M [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Fac. de Engenharia Agricola

2004-07-01

In this work, a pyrolysis model is presented in order to describe the pyrolysis kinetics of sewage sludge. Data were obtained from dynamic experiments, at heating rates of 5 to 20 deg C/min and in a temperature range of 40 to 900 deg C. A simple first order or near first order can predict reasonably well the final conversion reached, but, in what concerns the weight loss rate, a simple model cannot predict the peaks obtained in the weight loss rate. As it is shown, the best fit has been obtained by a model which takes into account four fractions which decompose independently following a first order kinetics. (author)

Thermodynamic analysis for syngas production from volatiles released in waste tire pyrolysis

International Nuclear Information System (INIS)

Martínez, Juan Daniel; Murillo, Ramón; García, Tomás; Arauzo, Inmaculada

2014-01-01

Highlights: • Pyrolysis experiments have been conducted in a continuous auger reactor. • Pyrolysis temperature influence on composition of both volatiles and char was studied. • A process for syngas production has been proposed from the volatiles. • Equivalence ratio down to 0.4 is a practical limit for syngas production. • The results provide essential data prior to perform any experimental campaign. - Abstract: This paper shows the maximum limit on syngas composition obtained from volatiles released in waste tire pyrolysis when they are submitted to an air–steam partial oxidation process. Thus, from mass and energy balances and a stoichiometric equilibrium model, syngas composition and reaction temperature as well as some process parameters were predicted by varying both the equivalence ratio (ER) and the steam to fuel ratio (SF). In addition, pyrolysis experiments were performed using a continuous auger reactor, and the influence of pyrolysis temperature on composition of both volatiles and char was studied. Consequently, the resulting syngas characteristics were correlated with the pyrolysis temperature. The stoichiometric equilibrium model showed that an ER down to 0.4 is a practical limit to perform the air–steam partial oxidation process. When the process is carried out only with air, volatiles obtained at high pyrolysis temperature lead to lower reaction temperature and higher LHV of syngas in comparison with those found at low pyrolysis temperature. The H 2 production is favored between 0.20 and 0.40 of ER and seems to be more influenced by the H/C ratio than by the water gas-shift reaction. On the other hand, the steam addition shows a more notable effect on the H 2 production for volatiles obtained at the highest pyrolysis temperature (600 °C) in agreement with the lower reaction temperature under these experimental conditions. This thermodynamic analysis provides essential data on the optimization of syngas production from volatiles

Thermochemical conversion of biomass in smouldering combustion across scales: The roles of heterogeneous kinetics, oxygen and transport phenomena.

Science.gov (United States)

Huang, Xinyan; Rein, Guillermo

2016-05-01

The thermochemical conversion of biomass in smouldering combustion is investigated here by combining experiments and modeling at two scales: matter (1mg) and bench (100g) scales. Emphasis is put on the effect of oxygen (0-33vol.%) and oxidation reactions because these are poorly studied in the literature in comparison to pyrolysis. The results are obtained for peat as a representative biomass for which there is high-quality experimental data published previously. Three kinetic schemes are explored, including various steps of drying, pyrolysis and oxidation. The kinetic parameters are found using the Kissinger-Genetic Algorithm method, and then implemented in a one-dimensional model of heat and mass transfer. The predictions are validated with thermogravimetric and bench-scale experiments and then analyzed to unravel the role of heterogeneous reaction. This is the first time that the influence of oxygen on biomass smouldering is explained in terms of both chemistry and transport phenomena across scales. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Deactivation and regeneration of ZSM-5 zeolite in catalytic pyrolysis of plastic wastes

International Nuclear Information System (INIS)

Lopez, A.; Marco, I. de; Caballero, B.M.; Adrados, A.; Laresgoiti, M.F.

2011-01-01

Highlights: → Pyrolysis transforms plastic wastes in valuable liquids and gases useful as fuels or source of chemicals. → The use of ZSM-5 zeolite in pyrolysis favours the production of gases and of lighter and more aromatic liquids. → ZSM-5 zeolite is almost completely deactivated after one plastics pyrolysis experiment. → ZSM-5 zeolite used in plastic wastes pyrolysis can be regenerated by burning the deposited coke in an air stream. → Regenerated ZSM-5 recovers its activity and produces liquids and gases equivalent to those obtained with fresh catalyst. - Abstract: In this work, a study of the regeneration and reuse of ZSM-5 zeolite in the pyrolysis of a plastic mixture has been carried out in a semi-batch reactor at 440 deg. C. The results have been compared with those obtained with fresh-catalyst and in non-catalytic experiments with the same conditions. The use of fresh catalyst produces a significant change in both the pyrolysis yields and the properties of the liquids and gases obtained. Gases more rich in C3-C4 and H 2 are produced, as well as lower quantities of aromatic liquids if compared with those obtained in thermal decomposition. The authors have proved that after one pyrolysis experiment the zeolite loses quite a lot of its activity, which is reflected in both the yields and the products quality; however, this deactivation was found to be reversible since after regeneration heating at 550 deg. C in oxygen atmosphere, this catalyst recovered its initial activity, generating similar products and in equivalent proportions as those obtained with fresh catalyst.

Pyrolysis mechanism of microalgae Nannochloropsis sp. based on model compounds and their interaction

International Nuclear Information System (INIS)

Wang, Xin; Tang, Xiaohan; Yang, Xiaoyi

2017-01-01

Highlights: • Pyrolysis experiments were conducted by model compounds of algal components. • Interaction affected little bio-crude yield of model compounds co-pyrolysis. • Some interaction pathways between microalgae components were recommended. • N-heterocyclic compounds were further pyrolysis products of Maillard reaction products. • Surfactant synthesis (lipid-amino acids and lipid-glucose) between algal components. - Abstract: Pyrolysis is one of important pathways to convert microalgae to liquid biofuels and key components of microalgae have different chemical composition and structure, which provides a barrier for large-scale microalgae-based liquid biofuel application. Microalgae component pyrolysis mechanism should be researched to optimal pyrolysis process parameters. In this study, single pyrolysis and co-pyrolysis of microalgal components (model compounds castor oil, soybean protein and glucose) were conducted to reveal interaction between them by thermogrametric analysis and bio-crude evaluation. Castor oil (model compound of lipid) has higher pyrolysis temperature than other model compounds and has the maximum contribution to bio-crude formation. Bio-crude from soybean protein has higher N-heterocyclic compounds as well as phenols, which could be important aromatic hydrocarbon source during biorefineries and alternative aviation biofuel production. Potential interaction pathways based on model compounds are recommended including further decomposition of Maillard reaction products (MRPs) and surfactant synthesis, which indicate that glucose played an important role on pyrolysis of microalgal protein and lipid components. The results should provide necessary information for microalgae pyrolysis process optimization and large-scale pyrolysis reactor design.

Thermogravimetric study and kinetic analysis of dried industrial sludge pyrolysis.

Science.gov (United States)

Liu, Guangrui; Song, Huijuan; Wu, Jinhu

2015-07-01

Thermogravimetric experiments of two different industrial sludge samples were carried out with non-isothermal temperature programs. The results indicated that the pyrolysis process contains three obvious stages and the main decomposition reaction occurred in the range of 200-600°C. The distributed activation energy model (DAEM) was also proposed describing equally well the pyrolysis behavior of the samples. The calculated activation energy was ranged from 170 to 593kJ/mol and 125 to 756kJ/mol for SLYG (sludge sample from chemical fiber factory) and SQD (sludge sample from woody industry), respectively. The reliability of this model not only provided good fit for all experiments, but also allowed accurate extrapolations to relative higher heating rates. Besides, the FTIR measurement was also used to further understand the relationship between pyrolysis behavior and chemical structures for industrial sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pyrolysis gas chromatographic atomic emission detection for sediments, coals and other petrochemical precursors

Energy Technology Data Exchange (ETDEWEB)

Seeley, J.A.; Zeng, Y.D.; Uden, P.C.; Eglinton, T.I.; Ericson, I. (Massachusetts University, Amherst, MA (USA). Dept. of Chemistry)

1992-09-01

On-line flash pyrolysis coupled to a capillary gas chromatograph for the characterization of marine sediments, coals and other heterogeneous solid samples is described. A helium microwave-induced plasma is used for chromatographic detection by atomic emission spectrometry. Simultaneous multi-element detection is achieved with a photodiode array detector. The optical path of the gas chromatographic atomic emission detector is purged with helium, allowing simultaneous, sensitive detection of atomic emission from sulfur 181 nm, phosphorous 186 nm, arsenic 189 nm, selenium 196 nm and carbon 193 nm. Several sediment and coal samples have been analysed for their carbon, nitrogen, sulfur, oxygen, phosphorous, arsenic and selenium content. Qualitative information indicating the occurrence and distribution of these elements in the samples can be used to gauge the relative stage of diagenetic evolution of the samples and provide information on their depositional environment. In some instances the chromatographic behaviour of the compounds produced upon pyrolysis is improved through on-line alkylation. This on-line derivatization is achieved by adding liquid reagents to the pyrolysis probe or by adding liquid reagents to the pyrolysis probe or by adding solid reagents either to the solid sample or by packing the reagent in the injection port of the chromatograph.

Experimental Investigation of Evolution of Pore Structure in Longmaxi Marine Shale Using an Anhydrous Pyrolysis Technique

Directory of Open Access Journals (Sweden)

Zhaodong Xi

2018-05-01

Full Text Available To better understanding the evolutionary characteristics of pore structure in marine shale with high thermal maturity, a natural Longmaxi marine shale sample from south China with a high equivalent vitrinite reflectance value (Ro = 2.03% was selected to conduct an anhydrous pyrolysis experiment (500–750 °C, and six artificial shale samples (pyrolysis products spanning a maturity range from Ro = 2.47% to 4.87% were obtained. Experimental procedures included mercury intrusion, nitrogen adsorption, and carbon dioxide adsorption, and were used to characterize the pore structure. In addition, fractal theory was applied to analyze the heterogeneous pore structure. The results showed that this sample suite had large differences in macropore, mesopore, and micropore volume (PV, as well as specific surface area (SSA and pore size distributions (PSD, at different temperatures. Micropore, mesopore, and macropore content increased, from being unheated to 600 °C, which caused the pore structure to become more complex. The content of small diameter pores (micropores and fine mesopores, <10 nm decreased and pores with large diameters (large mesopores and macropores, >10 nm slightly increased from 600 to 750 °C. Fractal analysis showed that larger pore sizes had more complicated pore structure in this stage. The variance in pore structure for samples during pyrolysis was related to the further transformation of organic matter and PSD rearrangement. According to the data in this study, two stages were proposed for the pore evolution for marine shale with high thermal maturity.

Modeling of biomass pyrolysis

International Nuclear Information System (INIS)

Samo, S.R.; Memon, A.S.; Akhund, M.A.

1995-01-01

The fuels used in industry and power sector for the last two decades have become expensive. As a result renewable energy source have been emerging increasingly important, of these, biomass appears to be the most applicable in the near future. The pyrolysis of biomass plays a key role amongst the three major and important process generally encountered in a gas producer, namely, pyrolysis, combustion and reduction of combustion products. Each biomass has its own pyrolysis characteristics and this important parameters must be known for the proper design and efficient operation of a gasification system. Thermogravimetric analysis has been widely used to study the devolatilization of solid fuels, such as biomass. It provides the weight loss history of a sample heated at a predetermined rate as a function of time and temperature. This paper presents the experimental results of modelling the weight loss curves of the main biomass components i.e. cellulose, hemicellulose and lignin. Thermogravimetric analysis of main components of biomass showed that pyrolysis is first order reaction. Furthermore pyrolysis of cellulose and hemicelluloe can be regarded as taking place in two stages, for while lignin pyrolysis is a single stage process. This paper also describes the Thermogravimetric Analysis (TGA) technique to predict the weight retained during pyrolysis at any temperature, for number of biomass species, such as cotton stalk, bagasse ad graoundnut shell. (author)

Pyrolysis characteristics of typical biomass thermoplastic composites

Directory of Open Access Journals (Sweden)

Hongzhen Cai

Full Text Available The biomass thermoplastic composites were prepared by extrusion molding method with poplar flour, rice husk, cotton stalk and corn stalk. The thermo gravimetric analyzer (TGA has also been used for evaluating the pyrolysis process of the composites. The results showed that the pyrolysis process mainly consists of two stages: biomass pyrolysis and the plastic pyrolysis. The increase of biomass content in the composite raised the first stage pyrolysis peak temperature. However, the carbon residue was reduced and the pyrolysis efficiency was better because of synergistic effect of biomass and plastic. The composite with different kinds of biomass have similar pyrolysis process, and the pyrolysis efficiency of the composite with corn stalk was best. The calcium carbonate could inhibit pyrolysis process and increase the first stage pyrolysis peak temperature and carbon residue as a filling material of the composite. Keywords: Biomass thermoplastic composite, Calcium carbonate, Pyrolysis characteristic

Laser induced pyrolysis techniques

International Nuclear Information System (INIS)

Vanderborgh, N.E.

1976-01-01

The application of laser pyrolysis techniques to the problems of chemical analysis is discussed. The processes occurring during laser pyrolysis are first briefly reviewed. The problems encountered in laser pyrolysis gas chromatography are discussed using the analysis of phenanthrene and binary hydrocarbons. The application of this technique to the characterization of naturally occurring carbonaceous material such as oil shales and coal is illustrated

Modelling solid-convective flash pyrolysis of straw and wood in the Pyrolysis Centrifuge Reactor

DEFF Research Database (Denmark)

Bech, Niels; Larsen, Morten Boberg; Jensen, Peter Arendt

2009-01-01

in the Pyrolysis Centrifuge Reactor, a novel solid-convective flash pyrolysis reactor. The model relies on the original concept for ablative pyrolysis of particles being pyrolysed through the formation of an intermediate liquid compound which is further degraded to form liquid organics, char, and gas. To describe...

Pyrolysis characteristics of typical biomass thermoplastic composites

Science.gov (United States)

Cai, Hongzhen; Ba, Ziyu; Yang, Keyan; Zhang, Qingfa; Zhao, Kunpeng; Gu, Shiyan

The biomass thermoplastic composites were prepared by extrusion molding method with poplar flour, rice husk, cotton stalk and corn stalk. The thermo gravimetric analyzer (TGA) has also been used for evaluating the pyrolysis process of the composites. The results showed that the pyrolysis process mainly consists of two stages: biomass pyrolysis and the plastic pyrolysis. The increase of biomass content in the composite raised the first stage pyrolysis peak temperature. However, the carbon residue was reduced and the pyrolysis efficiency was better because of synergistic effect of biomass and plastic. The composite with different kinds of biomass have similar pyrolysis process, and the pyrolysis efficiency of the composite with corn stalk was best. The calcium carbonate could inhibit pyrolysis process and increase the first stage pyrolysis peak temperature and carbon residue as a filling material of the composite.

Refining fast pyrolysis of biomass

NARCIS (Netherlands)

Westerhof, Roel Johannes Maria

2011-01-01

Pyrolysis oil produced from biomass is a promising renewable alternative to crude oil. Such pyrolysis oil has transportation, storage, and processing benefits, none of which are offered by the bulky, inhomogeneous solid biomass from which it originates. However, pyrolysis oil has both a different

Pyrolysis oil as diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Gros, S [Wartsila Diesel International Ltd., Vaasa (Finland). Diesel Technology

1997-12-31

Wood waste pyrolysis oil is an attractive fuel alternative for diesel engine operation. The main benefit is the sustainability of the fuel. No fossil reserves are consumed. The fact that wood waste pyrolysis oil does not contribute to CO{sub 2} emissions is of utmost importance. This means that power plants utilising pyrolysis oil do not cause additional global warming. Equally important is the reduced sulphur emissions that this fuel alternative implies. The sulphur content of pyrolysis oil is extremely low. The high water content and low heating value are also expected to result in very low NO{sub x} emissions. Utilisation of wood waste pyrolysis oil in diesel engines, however, involves a lot of challenges and problems to be solved. The low heating value requires a new injection system with high capacity. The corrosive characteristics of the fluid also underline the need for new injection equipment materials. Wood waste pyrolysis oil contains solid particles which can clog filters and cause abrasive wear. Wood waste pyrolysis oil has proven to have extremely bad ignition properties. The development of a reliable injection system which is able to cope with such a fuel involves a lot of optimisation tests, redesign and innovative solutions. Successful single-cylinder tests have already been performed and they have verified that diesel operation on wood pyrolysis oil is technically possible. (orig.)

Pyrolysis oil as diesel fuel

Energy Technology Data Exchange (ETDEWEB)

Gros, S. [Wartsila Diesel International Ltd., Vaasa (Finland). Diesel Technology

1996-12-31

Wood waste pyrolysis oil is an attractive fuel alternative for diesel engine operation. The main benefit is the sustainability of the fuel. No fossil reserves are consumed. The fact that wood waste pyrolysis oil does not contribute to CO{sub 2} emissions is of utmost importance. This means that power plants utilising pyrolysis oil do not cause additional global warming. Equally important is the reduced sulphur emissions that this fuel alternative implies. The sulphur content of pyrolysis oil is extremely low. The high water content and low heating value are also expected to result in very low NO{sub x} emissions. Utilisation of wood waste pyrolysis oil in diesel engines, however, involves a lot of challenges and problems to be solved. The low heating value requires a new injection system with high capacity. The corrosive characteristics of the fluid also underline the need for new injection equipment materials. Wood waste pyrolysis oil contains solid particles which can clog filters and cause abrasive wear. Wood waste pyrolysis oil has proven to have extremely bad ignition properties. The development of a reliable injection system which is able to cope with such a fuel involves a lot of optimisation tests, redesign and innovative solutions. Successful single-cylinder tests have already been performed and they have verified that diesel operation on wood pyrolysis oil is technically possible. (orig.)

Fast Pyrolysis of Lignin Using a Pyrolysis Centrifuge Reactor

DEFF Research Database (Denmark)

Trinh, Ngoc Trung; Jensen, Peter Arendt; Sárossy, Zsuzsa

2013-01-01

Fast pyrolysis of lignin from an ethanol plant was investigated on a lab scale pyrolysis centrifuge reactor (PCR) with respect to pyrolysis temperature, reactor gas residence time, and feed rate. A maximal organic oil yield of 34 wt % dry basis (db) (bio-oil yield of 43 wt % db) is obtained...... at temperatures of 500−550 °C, reactor gas residence time of 0.8 s, and feed rate of 5.6 g/min. Gas chromatography mass spectrometry and size-exclusion chromatography were used to characterize the Chemical properties of the lignin oils. Acetic acid, levoglucosan, guaiacol, syringols, and p-vinylguaiacol are found...... components and molecular mass distribution of the lignin oils. The obtained lignin oil has a very different components composition when compared to a beech wood oil....

Characterization of Thermo-Physical Properties of EVA/ATH: Application to Gasification Experiments and Pyrolysis Modeling

Directory of Open Access Journals (Sweden)

Bertrand Girardin

2015-11-01

Full Text Available The pyrolysis of solid polymeric materials is a complex process that involves both chemical and physical phenomena such as phase transitions, chemical reactions, heat transfer, and mass transport of gaseous components. For modeling purposes, it is important to characterize and to quantify the properties driving those phenomena, especially in the case of flame-retarded materials. In this study, protocols have been developed to characterize the thermal conductivity and the heat capacity of an ethylene-vinyl acetate copolymer (EVA flame retarded with aluminum tri-hydroxide (ATH. These properties were measured for the various species identified across the decomposition of the material. Namely, the thermal conductivity was found to decrease as a function of temperature before decomposition whereas the ceramic residue obtained after the decomposition at the steady state exhibits a thermal conductivity as low as 0.2 W/m/K. The heat capacity of the material was also investigated using both isothermal modulated Differential Scanning Calorimetry (DSC and the standard method (ASTM E1269. It was shown that the final residue exhibits a similar behavior to alumina, which is consistent with the decomposition pathway of EVA/ATH. Besides, the two experimental approaches give similar results over the whole range of temperatures. Moreover, the optical properties before decomposition and the heat capacity of the decomposition gases were also analyzed. Those properties were then used as input data for a pyrolysis model in order to predict gasification experiments. Mass losses of gasification experiments were well predicted, thus validating the characterization of the thermo-physical properties of the material.

Characterization of Thermo-Physical Properties of EVA/ATH: Application to Gasification Experiments and Pyrolysis Modeling.

Science.gov (United States)

Girardin, Bertrand; Fontaine, Gaëlle; Duquesne, Sophie; Försth, Michael; Bourbigot, Serge

2015-11-20

The pyrolysis of solid polymeric materials is a complex process that involves both chemical and physical phenomena such as phase transitions, chemical reactions, heat transfer, and mass transport of gaseous components. For modeling purposes, it is important to characterize and to quantify the properties driving those phenomena, especially in the case of flame-retarded materials. In this study, protocols have been developed to characterize the thermal conductivity and the heat capacity of an ethylene-vinyl acetate copolymer (EVA) flame retarded with aluminum tri-hydroxide (ATH). These properties were measured for the various species identified across the decomposition of the material. Namely, the thermal conductivity was found to decrease as a function of temperature before decomposition whereas the ceramic residue obtained after the decomposition at the steady state exhibits a thermal conductivity as low as 0.2 W/m/K. The heat capacity of the material was also investigated using both isothermal modulated Differential Scanning Calorimetry (DSC) and the standard method (ASTM E1269). It was shown that the final residue exhibits a similar behavior to alumina, which is consistent with the decomposition pathway of EVA/ATH. Besides, the two experimental approaches give similar results over the whole range of temperatures. Moreover, the optical properties before decomposition and the heat capacity of the decomposition gases were also analyzed. Those properties were then used as input data for a pyrolysis model in order to predict gasification experiments. Mass losses of gasification experiments were well predicted, thus validating the characterization of the thermo-physical properties of the material.

Modelling of pyrolysis of peat and biomass under combustion and gasification; Pyrolyysimalli turpeen ja biomassan poltolle ja kaasutukselle

Energy Technology Data Exchange (ETDEWEB)

Raiko, R.; Haukka, P.; Vehmaan-Kreula, M. [Tampere Univ. of Technology (Finland). Energy and Process Technology

1997-10-01

In the model developed during the research the chemical kinetics of pyrolysis is described with `the two competing reactions model`. Heat transfer in particle consists of convection and conduction. With the help of the model all the kinetic parameters of the two pyrolysis reactions are fitted with measured values. Also simple correlations for pyrolysis of peat under fluidized bed and pulverised flame conditions are given. The effect of the heating rate can be taken into account by using two competing Arrhenius-type reactions. In this model pyrolysis is modelled by using two reactions; one for the low temperature level and the other for the high temperature level. Both of these reactions consume the same unreacted fuel and this model is able to describe the pyrolysis at different temperature levels. Pyrolysis takes place in the heating stage of the particle before heterogeneous combustion and therefore temperature and density profiles inside the particle have to be solved simultaneously. The energy and mass balance equations of the particle form a set of partial differential equations (PDE), which is solved numerically by using so called method of lines, by converting PDE into a set of ordinary differential equations (ODE). The final solution of ODEs is received by using LSODE algorithm of Hindmash. An user friendly interface for the pyrolysis model is programmed by using Visual Basic enabling convenient variation of the conditions and observation of the results

Investigation of solid organic waste processing by oxidative pyrolysis

Science.gov (United States)

Kolibaba, O. B.; Sokolsky, A. I.; Gabitov, R. N.

2017-11-01

A thermal analysis of a mixture of municipal solid waste (MSW) of the average morphological composition and its individual components was carried out in order to develop ways to improve the efficiency of its utilization for energy production in thermal reactors. Experimental studies were performed on a synchronous thermal analyzer NETZSCH STA 449 F3 Jupiter combined with a quadrupole mass spectrometer QMC 403. Based on the results of the experiments, the temperature ranges of the pyrolysis process were determined as well as the rate of decrease of the mass of the sample of solid waste during the drying and oxidative pyrolysis processes, the thermal effects accompanying these processes, as well as the composition and volumes of gases produced during oxidative pyrolysis of solid waste and its components in an atmosphere with oxygen content of 1%, 5%, and 10%. On the basis of experimental data the dependences of the yield of gas on the moisture content of MSW were obtained under different pyrolysis conditions under which a gas of various calorific values was produced.

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

International Nuclear Information System (INIS)

Babich, I.V.; Hulst, M. van der; Lefferts, L.; Moulijn, J.A.; O'Connor, P.; Seshan, K.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na 2 CO 3 ) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor and characterized for water content and heating value. The oil composition was analyzed by GC-MS. Pretreatment of chlorella with Na 2 CO 3 influences the primary conversion of chlorella by shifting the decomposition temperature to a lower value. In the presence of Na 2 CO 3 , gas yield increased and liquid yield decreased when compared with non-catalytic pyrolysis at the same temperatures. However, pyrolysis oil from catalytic runs carries higher heating value and lower acidity. Lower content of acids in the bio-oil, higher aromatics, combined with higher heating value show promise for production of high-quality bio-oil from algae via catalytic pyrolysis, resulting in energy recovery in bio-oil of 40%. -- Highlights: → The pyrolytic catalytic conversion of chlorella algae to liquid fuel precursor. → Na 2 CO 3 as a catalyst for the primary conversion of chlorella. → Pyrolysis oil from catalytic runs carries higher heating value and lower acidity. → High-quality bio-oil from algae via catalytic pyrolysis with energy recovery in bio-oil of 40%.

Numerical modelling of pyrolysis in normal and reduced oxygen concentration

International Nuclear Information System (INIS)

Kacem, Ahmed

2016-01-01

The predictive capability of computational fluid dynamics (CFD) fire models depends on the accuracy with which the source term due to fuel pyrolysis can be determined. The pyrolysis rate is a key parameter controlling fire behavior, which in turn drives the heat feedback from the flame to the fuel surface. In the present study an in-depth pyrolysis model of a semi-transparent solid fuel (here, clear polymethyl methacrylate or PMMA) with spectrally-resolved radiation and a moving gas/solid interface was coupled with the CFD code ISIS of the IRSN which included turbulence, combustion and radiation for the gas phase. A combined genetic algorithm/pyrolysis model was used with Cone Calorimeter data from a pure pyrolysis experiment to estimate a unique set of kinetic parameters for PMMA pyrolysis. In order to validate the coupled model, ambient air flaming experiments were conducted on square slabs of PMMA with side lengths of 10, 20 and 40 cm. From measurements at the center of the slab, it was found that i) for any sample size, the experimental regression rate becomes almost constant with time, and ii) although the radiative and total heat transfers increase significantly with the sample size, the radiative contribution to the total heat flux remains almost constant (∼80%). Coupled model results show a fairly good agreement with the literature and with current measurements of the heat fluxes, gas temperature and regressing surface rate at the center of the slabs. Discrepancies between predicted and measured total pyrolysis rate are observed, which result from the underestimation of the flame heat flux feedback at the edges of the slab, as confirmed by the comparison between predicted and observed topography of burned samples. Predicted flame heights based on a threshold temperature criterion were found to be close to those deduced from the correlation of Heskestad. Finally, in order to predict the pyrolysis of PMMA under reduced ambient oxygen concentration, a two

The lignin pyrolysis composition and pyrolysis products of palm kernel shell, wheat straw, and pine sawdust

International Nuclear Information System (INIS)

Chang, Guozhang; Huang, Yanqin; Xie, Jianjun; Yang, Huikai; Liu, Huacai; Yin, Xiuli; Wu, Chuangzhi

2016-01-01

Highlights: • The primarily pyrolysis composition of PKS lignin was p-hydroxyphenyl unit. • Higher phenol yield and lower gas energy yield were obtained from PKS pyrolysis. • PKS produced more bio-oil and biochar than WS and PS from pyrolysis at 650–850 °C. • PKS-char had poorer gasification reactivity due to higher ordering carbon degree. - Abstract: The lignin monomer composition of palm kernel shell (PKS) was characterized using pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS), and the characteristics and distributions of products obtained from PKS pyrolysis were investigated using Py-GC/MS, GC, and a specially designed pyrolysis apparatus. The gasification reactivity of PKS biochar was also characterized using thermogravimetry (TG) and Raman spectroscopy. All the results were compared with those obtained from wheat straw (WS) and pine sawdust (PS). The results showed that PKS lignin is primarily composed of p-hydroxyphenyl structural units, while WS and PS lignins are mainly made up of guaiacyl units. Both the mass and energy yields of non-condensable gases from PKS pyrolysis were lower than those obtained from WS and PS pyrolysis at 650–850 °C, owing to the lower volatile content (75.21%) and lack of methoxy groups in PKS. Compared with WS and PS, higher bio-oil productivity was observed during PKS pyrolysis. Phenols were the main component of PKS bio-oil from pyrolysis at 500 °C, and the phenol content of PKS bio-oil (13.49%) was higher than in WS bio-oil (1.62%) and PS bio-oil (0.55%). A higher yield of biochar (on an ash-free basis) was also obtained from PKS pyrolysis. Because of its greater relative degree of ordered carbon, PKS biochar exhibited lower in situ reactivity during CO_2 or H_2O gasification than WS and PS biochars. A longer residence time and addition of steam were found to be beneficial during PKS biochar gasification.

Molten salt pyrolysis of milled beech wood using an electrostatic precipitator for oil collection

Directory of Open Access Journals (Sweden)

Heidi S. Nygård

2015-07-01

Full Text Available A tubular electrostatic precipitator (ESP was designed and tested for collection of pyrolysis oil in molten salt pyrolysis of milled beech wood (0.5-2 mm. The voltage-current (V-I characteristics were studied, showing most stable performance of the ESP when N2 was utilized as inert gas. The pyrolysis experiments were carried out in FLiNaK and (LiNaK2CO3 over the temperature range of 450-600 ℃. The highest yields of pyrolysis oil were achieved in FLiNaK, with a maximum of 34.2 wt% at 500 ℃, followed by a decrease with increasing reactor temperature. The temperature had nearly no effect on the oil yield for pyrolysis in (LiNaK2CO3 (19.0-22.5 wt%. Possible hydration reactions and formation of HF gas during FLiNaK pyrolysis were investigated by simulations (HSC Chemistry software and measurements of the outlet gas (FTIR, but no significant amounts of HF were detected.

Effluent Gas Flux Characterization During Pyrolysis of Chicken Manure

Science.gov (United States)

Clark, S. C.; Ryals, R.; Miller, D. J.; Mullen, C. A.; Pan, D.; Zondlo, M. A.; Boateng, A. A.; Hastings, M. G.

2017-12-01

Pyrolysis is a viable option for the production of agricultural resources from diverted organic waste streams and renewable bioenergy. This high temperature thermochemical process yields material with beneficial reuses, including bio-oil and biochar. Gaseous forms of carbon (C) and nitrogen (N) are also emitted during pyrolysis. The effluent mass emission rates from pyrolysis are not well characterized, thus limiting proper evaluation of the environmental benefits or costs of pyrolysis products. We present the first comprehensive suite of C and N mass emission rate measurements of a biomass pyrolysis process using chicken manure as feedstock to produce biochar and bio-oil. Two chicken manure fast pyrolysis experiments were conducted at controlled temperature ranges of 450 - 485 °C and 550 - 585 °C. Mass emission rates of N2O, NO, CO, CO2, CH4 and NH3 were measured using trace gas analyzers. Based on the system mass balance, 23-25% of the total mass of the manure feedstock was emitted as gas, while 52-55% and 23% were converted to bio-oil and biochar, respectively. CO2 and NH3 were the dominant gaseous species by mass, accounting for 58 - 65% of total C mass emitted and 99% of total reactive N mass emitted, respectively. Our gas flux measurements suggest that 1.4 to 2.7 g NH3 -N would be produced from the pyrolysis of one kg of manure. Conservatively scaling up these NH3 pyrolysis emissions in the Chesapeake Bay Watershed, where an estimated 8.64 billion kg of poultry manure is applied to agricultural soils every year, as much as 1.2 x 107 kg of NH3 could be emitted into the atmosphere annually, increasing the potential impact of atmospheric N deposition without a mechanism to capture the gas exhaust during pyrolysis. However, this is considerably less than the potential emissions from NH3 volatilization of raw chicken manure applications, which can be 20-60% of total N applied, and amount to 3.4 x 107 - 1.0 x 108 kg NH3-N yr-1. Pyrolysis has the potential to

Fast pyrolysis of oil palm shell (OPS)

Science.gov (United States)

Abdullah, Nurhayati; Sulaiman, Fauziah; Aliasak, Zalila

2015-04-01

Biomass is an important renewable source of energy. Residues that are obtained from harvesting and agricultural products can be utilised as fuel for energy generation by conducting any thermal energy conversion technology. The conversion of biomass to bio oil is one of the prospective alternative energy resources. Therefore, in this study fast pyrolysis of oil palm shell was conducted. The main objective of this study was to find the optimum condition for high yield bio-oil production. The experiment was conducted using fixed-bed fluidizing pyrolysis system. The biomass sample was pyrolysed at variation temperature of 450°C - 650°C and at variation residence time of 0.9s - 1.35s. The results obtained were further discussed in this paper. The basic characteristic of the biomass sample was also presented here. The experiment shows that the optimum bio-oil yield was obtained at temperature of 500°C at residence time 1.15s.

Production, properties and utilisation of pyrolysis oil

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K; Oasmaa, A; Arpiainen, V; Solantausta, Y; Leppaemaeki, E; Kuoppala, E; Levander, J; Kleemola, J; Saarimaeki, P [VTT Energy, Jyvaeskylae (Finland). Energy Production Technologies

1997-12-01

In this project VTT Energy co-ordinates the EU JOULE Project `Biofuel oil for power plants and boilers` supporting the development projects of Finnish enterprises, and participates in the Pyrolysis Project of IEA Bioenergy Agreement. Presently two pyrolysis devices with capacities of 150 g/h and 1 kg/h are used for the project. Hot gas filtering tests by using one ceramic candle equipment have been carried out with the 1 kg/h device for pyrolysis oil. The solids and alkali contents of the product oil were reduced clearly. Suitable conditions are being defined for continuous hot gas filtering. A PDU device of 20 kg/h is being commissioned. The main aim of the chemical characterisation of pyrolysis oil was to develop as simple a method as possible for differentiating pyrolysis oils and for finding correlations between the characteristics and behaviour of pyrolysis oils. Pyrolysis oils produced from various raw materials (hardwood, pine, straw) were analysed and compared with each other. VTT Energy participates in the pyrolysis network (EU/PYNE) of EU, the aim of which is to collect and disseminate research results of pyrolysis studies, i.e., through a journal with a wide circulation. VTT also participates in the pyrolysis activity of IEA (PYRA), the other partners being Great Britain, EU, Canada and the United States. I.e., quality criteria and improvement, occupational safety and pyrolysis kinetics are discussed in IEA/PYRA

Catalytic biomass pyrolysis process

Science.gov (United States)

Dayton, David C.; Gupta, Raghubir P.; Turk, Brian S.; Kataria, Atish; Shen, Jian-Ping

2018-04-17

Described herein are processes for converting a biomass starting material (such as lignocellulosic materials) into a low oxygen containing, stable liquid intermediate that can be refined to make liquid hydrocarbon fuels. More specifically, the process can be a catalytic biomass pyrolysis process wherein an oxygen removing catalyst is employed in the reactor while the biomass is subjected to pyrolysis conditions. The stream exiting the pyrolysis reactor comprises bio-oil having a low oxygen content, and such stream may be subjected to further steps, such as separation and/or condensation to isolate the bio-oil.

Experimental investigation of flash pyrolysis oil droplet combustion

DEFF Research Database (Denmark)

Ibrahim, Norazana; Jensen, Peter A.; Dam-Johansen, Kim

2013-01-01

at a temperature ranging between 1000 and 1400°C with an initial gas velocity of 1.6 m/s and oxygen concentration of 3%. The evolution of combustion of bio-oil droplets was recorded by a digital video camera. It was observed that the combustion behaviour of pyrolysis oil droplet differ from the heavy oil in terms......The aim of this work is to investigate and compare the combustion behaviour of a single droplet of pyrolysis oil derived from wheat straw and heavy fossil oil in a single droplet combustion chamber. The initial oil droplet diameters were in between 500 μm to 2500 μm. The experiments were performed...

Kinetic Study on Pyrolysis of Oil Palm Frond

International Nuclear Information System (INIS)

Soon, V S Y; Chin, B L F; Lim, A C R

2016-01-01

The pyrolysis of oil palm frond is studied using thermogravimetric analysis (TGA) equipment. The present study investigates the thermal degradation behaviour and determination of the kinetic parameters such as the activation energy (E A ) and pre-exponential factor (A) values of oil palm frond under pyrolysis condition. The kinetic data is produced based on first order rate of reaction. In this study, the experiments are conducted at different heating rates of 10, 20, 30, 40 and 50 K/min in the temperature range of 323-1173 K under non-isothermal condition. Argon gas is used as an inert gas to remove any entrapment of gases in the TGA equipment. (paper)

Catalytic co-pyrolysis of cellulose and polypropylene over all-silica mesoporous catalyst MCM-41 and Al-MCM-41.

Science.gov (United States)

Chi, Yongchao; Xue, Junjie; Zhuo, Jiankun; Zhang, Dahu; Liu, Mi; Yao, Qiang

2018-08-15

Fast pyrolysis is one of the most economical and efficient technologies to convert biomass to bio-oil and valuable chemical products. Co-pyrolysis with hydrogen rich materials such as plastics over zeolite catalysts is one of the significant solutions to various problems of bio-oil such as high oxygen content, low heat value and high acid content. This paper studied pyrolysis of cellulose and polypropylene (PP) separately and co-pyrolysis of cellulose and PP over MCM-41 and Al-MCM-41. The pyrolysis over different heating rates (10K/min, 20K/min, 30K/min) was studied by Thermogravimetry Analysis (TGA) and kinetic parameters were obtained by Coats-Redfern method and isoconversion method. TG and DTG data shows that the two catalysts advance the pyrolysis reaction of PP significantly and reduce its peak temperature of DTG curve from 458°C to 341°C. The activation energy of pyrolysis of PP also has a remarkable reduction over the two catalysts. Py-GC/MS method was used to obtain the product distribution of pyrolysis of cellulose and PP separately and co-pyrolysis of cellulose and PP over MCM-41 and Al-MCM-41 at constant temperature of 650°C. Experiment results proved that co-pyrolysis with PP bring significant changes to the product distribution of cellulose. Oxygenated compounds such as furans are decreased, while yields of olefins and aromatics increase greatly. The yield of furans increases with the catalysis of MCM-41 as for the pyrolysis of cellulose and co-pyrolysis, while the yield of olefins and aromatics both experience significant growth over Al-MCM-41, which can be explained by the abundant acid centers in Al-MCM-41. Copyright © 2018 Elsevier B.V. All rights reserved.

Pyrolysis of superfine pulverized coal. Part 3. Mechanisms of nitrogen-containing species formation

International Nuclear Information System (INIS)

Liu, Jiaxun; Jiang, Xiumin; Shen, Jun; Zhang, Hai

2015-01-01

Highlights: • NH 3 and NO formation mechanisms during superfine pulverized coal pyrolysis are investigated. • Influences of temperature, heating rate, particle size, atmosphere, and acid wash on the NH 3 and NO formation are analyzed. • Transformations of nitrogen-containing structures in coal/char during pyrolysis are recognized through XPS observation. • Relationships among nitrogen-containing gaseous species during pyrolysis are discussed. - Abstract: With more stringent regulations being implemented, elucidating the formation mechanisms of nitrogen-containing species during the initial pyrolysis step becomes important for developing new NO x control strategies. However, there is a lack of agreement on the origins of NO x precursors during coal pyrolysis, in spite of extensive investigations. Hence, it is important to achieve a more precise knowledge of the formation mechanisms of nitrogen-contain species during coal pyrolysis. In this paper, pyrolysis experiments of superfine pulverized coal were performed in a fixed bed at low heating rates. The influences of temperature, coal type, particle size and atmosphere on the NH 3 and NO evolution were discussed. There is a central theme to develop knowledge of the relationship between particle sizes and evolving behaviors of nitrogen-containing species. Furthermore, the catalytic role of inherent minerals in coal was proved to be effective on the partitioning of nitrogen during coal pyrolysis. In addition, the conversion pathways of heteroaromatic nitrogen structures in coal/char during pyrolysis were recognized through the X-ray photoelectron spectroscopy (XPS) analysis. Large quantities of pyridinic and quanternary nitrogen functionalities were formed during the thermal degradation. Finally, the relationships among the nitrogen-containing gaseous species during coal pyrolysis were discussed. In brief, a comprehensive picture of the volatile-nitrogen partitioning during coal pyrolysis is obtained in this

Yields from pyrolysis of refinery residue using a batch process

Directory of Open Access Journals (Sweden)

S. Prithiraj

2017-12-01

Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

Pyrolysis of spent ion-exchanger resins

International Nuclear Information System (INIS)

Slametschka, Rainer; Braehler, Georg

2012-01-01

Initial tests have shown that ion exchangers (IEX) can be decomposed by pyrolysis with very good results, yielding an inert and chemically resistant product. No additives are necessary. The main constituent of the product, the pyrolysis residues or ash, is carbon. It has been discovered that the entire radioactive inventory remains in the pyrolysis residues during pyrolysis of the IEX. This is achieved by relatively low process temperatures that prevent highly volatile nuclides such as the caesium nuclides from passing into the gaseous phase. Sintered metal filters in pyrolysis plant ensure that even the radioactivity bonded to the dust remains in the pyrolysis residues. In addition to the radionuclides, the main constituents of the residue are carbon from the original polystyrene matrix and sulphur from the functional groups. The pyrolysis residues form a flowable solid material and not a melt. It is thus easy to handle and can be compacted or cemented, depending on the requirements for interim and permanent storage. Any further constituents such as inorganic filter materials or even other organic materials do not interfere with the process, they are dried, calcined or also pyrolysed. (orig.)

Pyrolysis of Cigarette Ingredients Labelled with Stable Isotopes

Directory of Open Access Journals (Sweden)

Stotesbury S

2014-12-01

Full Text Available It is important to know how tobacco additives behave when cigarettes are smoked, whether they transfer intact to the smoke or whether there is any decomposition during smoking. Pyrolysis-GC-MS is a technique that can be focussed upon the effects of combustion from a single material free from interference from the complex mixture of different components present in the smoke. However, because pyrolysis is a model technique, the results need to be validated by comparison with cigarette smoke chemistry. In a previous paper we presented such a method for modelling the smoke chemistry from a burning cigarette using pyrolysis-GC-MS. The transfer and the extent of degradation of anisole, p-anisaldehyde, benzaldehyde, isoamylisovalerate, methyl trans-cinnamate and vanillin within a burning cigarette were estimated using this pyrolysis method. When these data were compared with results from smoke studies from 14C-analogues of the materials, the high levels of transfer predicted by pyrolysis were found to be generally consistent with the smoke chemistry data. However, there were still two outstanding issues. Firstly, there was some ambiguity in the labelled study about whether vanillin actually transferred without degradation or not. Furthermore, the results from the 14C-labelled study showed a greater extent of degradation for p-anisaldehyde than that indicated from the pyrolysis experiments. The purpose of the current study was to present some new information obtained to address these questions by better understanding the effect upon the smoke chemistry from adding vanillin and p-anisaldehyde, and the relationship between the smoke chemistry and the pyrolysis results. Components were identified in the smoke from cigarettes loaded with p-anisaldehyde and vanillin labelled with 18O and 13C. The extent of degradation from each additive was estimated by identifying labelled degradation products in the smoke. Because there was a clear distinction between the

Evaluating the susceptibility of pyrolysis of monosaccharide, disaccharide, and polysaccharide to CO_2

International Nuclear Information System (INIS)

Lee, Jechan; Tsang, Yiu Fai; Oh, Jeong-Ik; Lee, Sang-Ryong; Kwon, Eilhann E.

2017-01-01

Highlights: • Two-stage pyrolyzer gives a deep insight into sensitivity of biomass structure to CO_2. • The influence of CO_2 in pyrolysis of biomass occurs selectively. • Hemicellulose and lignin are highly sensitive to CO_2 in pyrolysis. • Thermal cracking of VOCs can be expedited by using CO_2 in pyrolysis. - Abstract: This study is aiming at exploring the genuine role of CO_2 in pyrolysis of lignocellulosic biomass by investigating the susceptibility of pyrolysis of monosaccharide (e.g., xylose and glucose), disaccharide (e.g., sucrose), and polysaccharide (e.g., woody biomass) to CO_2. To do this, the thermal degradation of these four biomass samples was characterized in N_2 and CO_2. The thermal characterization results reveal that the physical aspects of biomass decomposition (i.e., thermal degradation rate and residual mass difference) associated with CO_2 were nearly the same; however, the chemical aspects were significantly different. In other words, CO_2 enhanced thermal cracking of volatile organic compounds (VOCs) generated from thermal degradation of biomass. In addition, our experiment results show that xylose (a major constituent of hemicellulose) and lignin exhibited a high sensitivity to CO_2 in pyrolysis.

Release of Chlorine and Sulfur during Biomass Torrefaction and Pyrolysis

DEFF Research Database (Denmark)

Saleh, Suriyati Binti; Flensborg, Julie Pauline; Shoulaifar, Tooran Khazraie

2014-01-01

The release of chlorine (Cl) and sulfur (S) during biomass torrefaction and pyrolysis has been investigated via experiments in two laboratory-scale reactors: a rotating reactor and a fixed bed reactor. Six biomasses with different chemical compositions covering a wide range of ash content and ash...... reporting that biomasses with a lower chlorine content release a higher fraction of chlorine during the pyrolysis process. A significant sulfur release (about 60%) was observed from the six biomasses investigated at 350 degrees C. The initial sulfur content in the biomass did not influence the fraction...

Fractional condensation of biomass pyrolysis vapors

NARCIS (Netherlands)

Westerhof, Roel Johannes Maria; Brilman, Derk Willem Frederik; Garcia Perez, M.; Wang, Zhouhong; Oudenhoven, Stijn; van Swaaij, Willibrordus Petrus Maria; Kersten, Sascha R.A.

2011-01-01

In this paper, we have investigated the possibilities to steer the composition and, thus, the quality of pyrolysis liquids by the reactor temperature and the pyrolysis vapor condenser temperature. Pine wood was pyrolyzed in a 1 kg/h fluidized-bed pyrolysis reactor operated at 330 or 480 °C. The

Application of heterogeneous method for the interpretation of exponential experiments

International Nuclear Information System (INIS)

Birkhoff, G.; Bondar, L.

1977-01-01

The present paper gives a brief review of a work which was executed mainly during 1967 and 1968 in the field of the application of heterogeneous methods for the interpretation of exponential experiments with ORGEL type lattices (lattices of natural uranium cluster elements with organic coolants moderated by heavy water). In the frame of this work a heterogeneous computer program, in (r,γ) geometry was written which is based on the NORDHEIM method using a uniform moderator, three energy groups and monopol and dipol sources. This code is especially adapted for regular square lattices in a cylindrical tank. Full use of lattice symmetry was made for reducing the numerical job of the theory. A further reduction was obtained by introducing a group averaged extrapolation distance at the external boundary. Channel parameters were evaluated by the PINOCCHIO code. Comparisons of calculated and measured thermal neutron flux showed good agreement. Equivalence of heterogeneous and homogeneous theory was found in cases of lattices comprising a minimum of 32, 24 and 16 fuel elements for respectively under-, well-, and over-moderated lattices. Heterogeneous calculations of high leakage lattices suffered the lack of good methods for the computation of axial and radial streaming parameters. Interpretation of buckling measurements in the subcritical facility EXPO requires already more accurate evaluation of the streaming effects than we made. The potential of heterogeneous theory in the field of exponential experiments is thought to be limited by the precision by which the streaming parameters can be calculated

Pyrolysis of wastes generated through saccharification of oak tree by using CO2 as reaction medium

International Nuclear Information System (INIS)

Kim, Jieun; Lee, Jechan; Kim, Ki-Hyun; Ok, Yong Sik; Jeon, Young Jae; Kwon, Eilhann E.

2017-01-01

Highlights: • Potential utilization of biomass waste generated from bioethanol production. • Enhanced generation of syngas from pyrolysis of oak tree waste by using CO 2 . • Reduction of tar formation in pyrolysis of oak tree waste. • Modification of morphology of oak tree waste biochar by using CO 2 in pyrolysis. - Abstract: In this study, the production of bioethanol was evaluated through a series of saccharification and fermentation of lignocellulosic biomass (e.g., oak tree) pre-treated with H 2 SO 4 , NH 3 , or NaOH using a yeast (Pichia stipitis). In addition, it was investigated the effects of CO 2 on pyrolysis of the biomass wastes remaining after saccharification of the three pre-treated oak tree (BWs: BW-H 2 SO 4 , BW-NH 3 , and BW-NaOH). Thus, this work emphasizes the mechanistic understanding of CO 2 in pyrolysis of BWs. The effect of CO 2 was most noticeable in syngas, as the ratio of CO and H 2 exhibited a 20 to 30-fold increase at >550 °C. The CO/H 2 ratio of pyrolysis of the waste in CO 2 is ∼1100% of that of pyrolysis of the waste in N 2 at 720 °C. Such proliferation of syngas led to the subsequent reduction of tar since the substantial amount of tar was consumed as a precursor of syngas: CO 2 not only expedited the thermal cracking of volatile organic compounds (VOCs), but also reacted with those VOCs. The morphologic modification of biochars also occurred in the presence of CO 2 via heterogeneous reaction between CO 2 and surface of BWs. In summary, this study shows a utilization of an oak tree waste generated from saccharification for bioethanol production as a pyrolysis feedstock to recover energy (i.e., syngas production). The use of CO 2 as pyrolysis medium not only enhanced syngas production from oak tree waste but also reduced tar formation by thermal decomposition of VOCs and reaction between VOCs and CO 2 . The process shown in this study can be used as a potential high energy recovery from a biomass waste by utilizing potent

Pyrolysis technologies for municipal solid waste: A review

Energy Technology Data Exchange (ETDEWEB)

Chen, Dezhen, E-mail: chendezhen@tongji.edu.cn [Thermal and Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); Yin, Lijie; Wang, Huan [Thermal and Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); He, Pinjing [State Key Laboratory of Pollution Control and Resource Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China)

2014-12-15

Highlights: • MSW pyrolysis reactors, products and environmental impacts are reviewed. • MSW pyrolysis still has to deal with flue gas emissions and products’ contamination. • Definition of standardized products is suggested to formalize MSW pyrolysis technology. • Syngas is recommended to be the target product for single MSW pyrolysis technology. - Abstract: Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO{sub 2} and NH{sub 3}, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.

Pyrolysis Process and Characteristics of Products from Sawdust Briquettes

Directory of Open Access Journals (Sweden)

Hua Yang

2016-01-01

Full Text Available The pyrolysis of briquettes made from biomass is an available and economic technological route for the production of briquette charcoal, but by-products (tar and gas cannot be brought into full utilization, leading to the waste of resources and the addition of environmental concerns. Temperature is the most important parameter that affects the distributions and properties of briquette charcoal. This work investigated the three kinds of products of the pyrolysis of sawdust briquette in a fixed bed across a wide temperature range (250 to 950 °C. The purpose of this experiment was to study the pyrolysis process and the properties of the resulting products (briquette charcoal, liquid, and gas of sawdust briquettes and explore the optimum operating temperature to generate good quality briquette charcoal, liquid, and gaseous products simultaneously. According to the results, the optimum pyrolysis temperature range was 450 to 650 °C, for which the briquette charcoal produced within this range had the highest calorific value (2,9.14 to 30.21 MJ/kg. Meanwhile, the liquid product is considered to be useful for liquid fuels or valuable chemical materials, and the low heating value of the gaseous product was 11.79 to 14.85 MJ/Nm3 in this temperature range.

Pyrolysis characteristics and pyrolysis products separation for recycling organic materials from waste liquid crystal display panels

Energy Technology Data Exchange (ETDEWEB)

Wang, Ruixue; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

2016-01-25

Highlights: • Pyrolysis characteristics are conducted for a better understanding of LCDs pyrolysis. • Optimum design is developed which is significant to guide the further industrial process. • Acetic acid and TPP are recycled and separated. - Abstract: Waste liquid crystal display (LCD) panels mainly contain inorganic materials (glass substrate with indium-tin oxide film), and organic materials (polarizing film and liquid crystal). The organic materials should be removed beforehand since the organic matters would hinder the indium recycling process. In the present study, pyrolysis process is used to remove the organic materials and recycle acetic as well as and triphenyl phosphate (TPP) from waste LCD panels in an environmental friendly way. Several highlights of this study are summarized as follows: (i) Pyrolysis characteristics and pyrolysis kinetics analysis are conducted which is significant to get a better understanding of the pyrolysis process. (ii) Optimum design is developed by applying Box–Behnken Design (BBD) under response surface methodology (RSM) for engineering application which is significant to guide the further industrial recycling process. The oil yield could reach 70.53 wt% and the residue rate could reach 14.05 wt% when the pyrolysis temperature is 570 °C, nitrogen flow rate is 6 L min{sup −1} and the particle size is 0.5 mm. (iii) Furthermore, acetic acid and TPP are recycled, and then separated by rotary evaporation, which could reduce the consumption of fossil energy for producing acetic acid, and be reused in electronics manufacturing industry.

Pyrolysis characteristics and pyrolysis products separation for recycling organic materials from waste liquid crystal display panels

International Nuclear Information System (INIS)

Wang, Ruixue; Xu, Zhenming

2016-01-01

Highlights: • Pyrolysis characteristics are conducted for a better understanding of LCDs pyrolysis. • Optimum design is developed which is significant to guide the further industrial process. • Acetic acid and TPP are recycled and separated. - Abstract: Waste liquid crystal display (LCD) panels mainly contain inorganic materials (glass substrate with indium-tin oxide film), and organic materials (polarizing film and liquid crystal). The organic materials should be removed beforehand since the organic matters would hinder the indium recycling process. In the present study, pyrolysis process is used to remove the organic materials and recycle acetic as well as and triphenyl phosphate (TPP) from waste LCD panels in an environmental friendly way. Several highlights of this study are summarized as follows: (i) Pyrolysis characteristics and pyrolysis kinetics analysis are conducted which is significant to get a better understanding of the pyrolysis process. (ii) Optimum design is developed by applying Box–Behnken Design (BBD) under response surface methodology (RSM) for engineering application which is significant to guide the further industrial recycling process. The oil yield could reach 70.53 wt% and the residue rate could reach 14.05 wt% when the pyrolysis temperature is 570 °C, nitrogen flow rate is 6 L min"−"1 and the particle size is 0.5 mm. (iii) Furthermore, acetic acid and TPP are recycled, and then separated by rotary evaporation, which could reduce the consumption of fossil energy for producing acetic acid, and be reused in electronics manufacturing industry.

TG study on pyrolysis of biomass and its three components under syngas

Energy Technology Data Exchange (ETDEWEB)

Gang Wang; Wen Li; Baoqing Li; Haokan Chen [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

2008-04-15

Pyrolysis of sawdust and its three components (cellulose, hemicellulose and lignin) were performed in a thermogravimetric analyzer (TGA92) under syngas and hydrogen. The effect of different heating rates (5, 10, 15 and 20{sup o}C/min) on the pyrolysis of these samples were examined. The pyrolysis tests of the synthesized samples (a mixture of the three components with different ratios) were also done under syngas. The distributed activation energy model (DAEM) was used to study the pyrolysis kinetics. It is found that syngas could replace hydrogen in hydropyrolysis process of biomass. Among the three components, hemicellulose would be the easiest one to be pyrolyzed and then would be cellulose, while lignin would be the most difficult one. Heating rate could not only affect the temperature at which the highest weight loss rate reached, but also affect the maximum value of weight loss rate. Both lignin and hemicellulose used in the experiments could affect the pyrolysis characteristic of cellulose while they could not affect each other obviously in the pyrolysis process. Values of k{sub 0} (frequency factor) change very greatly with different E (activation energy) values. The E values of sawdust range from 161.9 to 202.3 kJ/mol, which is within the range of activation energy values for cellulose, hemicellulose and lignin. 22 refs., 4 figs., 2 tabs.

Effect of the Presence of Chlorates and Perchlorates on the Pyrolysis of Organic Compounds: Implications for Measurements Done with the SAM Experiment Onboard the Curiosity Rover

Science.gov (United States)

Millan, M.; Szopa, C.; Buch, A.; Belmahdi, I.; Coll, P.; Glavin, D. P.; Freissinet, C.; Archer, P. D., Jr.; Sutter, B.; Summons, R. E.;

Effects of heating rate on slow pyrolysis behavior, kinetic parameters and products properties of moso bamboo.

Science.gov (United States)

Chen, Dengyu; Zhou, Jianbin; Zhang, Qisheng

2014-10-01

Effects of heating rate on slow pyrolysis behaviors, kinetic parameters, and products properties of moso bamboo were investigated in this study. Pyrolysis experiments were performed up to 700 °C at heating rates of 5, 10, 20, and 30 °C/min using thermogravimetric analysis (TGA) and a lab-scale fixed bed pyrolysis reactor. The results show that the onset and offset temperatures of the main devolatilization stage of thermogravimetry/derivative thermogravimetry (TG/DTG) curves obviously shift toward the high-temperature range, and the activation energy values increase with increasing heating rate. The heating rate has different effects on the pyrolysis products properties, including biochar (element content, proximate analysis, specific surface area, heating value), bio-oil (water content, chemical composition), and non-condensable gas. The solid yields from the fixed bed pyrolysis reactor are noticeably different from those of TGA mainly because the thermal hysteresis of the sample in the fixed bed pyrolysis reactor is more thorough. Copyright © 2014 Elsevier Ltd. All rights reserved.

Co-pyrolysis characteristics and kinetics of coal and plastic blends

International Nuclear Information System (INIS)

Zhou Limin; Luo Taian; Huang Qunwu

2009-01-01

Co-pyrolysis behaviors of different plastics (high density polyethylene, low density polyethylene and polypropylene), low volatile coal (LVC) and their mixtures were investigated by TGA. Experiments were conducted under N 2 atmosphere at heating rate of 20 deg. C/min from room temperature to 750 deg. C. The results showed that the thermal degradation temperature range of plastic was 438-521 deg. C, while that of coal (LVC) was 174-710 deg. C. Plastics showed similar pyrolysis characteristics due to similar chemical bonds in their molecular structures. The overlapping degradation temperature interval between coal and plastic provide an opportunity for free radicals from coal pyrolysis to participate in the reactions of plastic decomposition. The difference of weight loss percent (ΔW) between experimental and theoretical ones, calculated as an algebraic sum of those from each separated component, ΔW is 2.0-2.7% at the pyrolysis temperature higher than 530 deg. C, which indicates that the synergistic effect during pyrolysis occurs mainly in the high temperature region. The kinetic studies were performed according to Coats and Redfern method for first-order reaction. It was found that for plastics (HDPE, LDPE and PP), the pyrolysis process can be described by one first-order reaction. However, for LVC and LVC/plastic blends, this process can be described by three and four consecutive first-order reactions, respectively. The estimated kinetic parameters viz., activation energies and pre-exponential factors for coal, plastic and their blends, were found to be in the range of 35.7-572.8 kJ/mol and 27-1.7 x 10 38 min -1 , respectively

Pyrolysis and catalytic pyrolysis as a recycling method of waste CDs originating from polycarbonate and HIPS

Energy Technology Data Exchange (ETDEWEB)

Antonakou, E.V. [Department of Chemistry, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Kalogiannis, K.G.; Stephanidis, S.D. [Chemical Process Engineering Research Institute, 57001 Thermi, Thessaloniki (Greece); Triantafyllidis, K.S. [Department of Chemistry, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece); Chemical Process Engineering Research Institute, 57001 Thermi, Thessaloniki (Greece); Lappas, A.A. [Chemical Process Engineering Research Institute, 57001 Thermi, Thessaloniki (Greece); Achilias, D.S., E-mail: axilias@chem.auth.gr [Department of Chemistry, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece)

2014-12-15

Highlights: • Thermal and catalytic pyrolysis is a powerful method for recycling of WEEEs. • Liquid products obtained from the pyrolysis of PC or HIPS found in waste CDs are very different. • Mainly phenols are obtained from pyrolysis PC based wastes while aromatics from HIPS. • Use of MgO catalyst increases the amount of phenols from CD recycling compared to ZSM-5. • Use of MgO or ZSM-5 catalysts reduces the amount of styrene recovered from HIPS. - Abstract: Pyrolysis appears to be a promising recycling process since it could convert the disposed polymers to hydrocarbon based fuels or various useful chemicals. In the current study, two model polymers found in WEEEs, namely polycarbonate (PC) and high impact polystyrene (HIPS) and their counterparts found in waste commercial Compact Discs (CDs) were pyrolysed in a bench scale reactor. Both, thermal pyrolysis and pyrolysis in the presence of two catalytic materials (basic MgO and acidic ZSM-5 zeolite) was performed for all four types of polymers. Results have shown significant recovery of the monomers and valuable chemicals (phenols in the case of PC and aromatic hydrocarbons in the case of HIPS), while catalysts seem to decrease the selectivity towards the monomers and enhance the selectivity towards other desirable compounds.

Time resolved pyrolysis of char

DEFF Research Database (Denmark)

Egsgaard, H.; Ahrenfeldt, J.; Henriksen, U.B.

pyrolysis, and slow heating in direct combination with mass spectrometry, gas chromatography/mass spectrometry and flame ionization detection, respectively. Characteristic ions derived from the flash pyrolysis-gas chromatography/mass spectrometry data enable the release of volatiles to be time and, hence...

Pyrolysis of fibre residues with plastic contamination from a paper recycling mill: Energy recoveries

International Nuclear Information System (INIS)

Brown, Logan Jeremy; Collard, François-Xavier; Görgens, Johann

2017-01-01

Highlights: • Pyrolysis of fibre-plastics residues from paper recycling mill into fuel products. • Product with remarkable energy content up to 42.8 MJ/kg. • Influence of temperature on the product yields and fuel properties. • Effect of plastic composition on product properties. - Abstract: Pyrolysis is a promising technology for the production of marketable energy products from waste mixtures, as it decomposes heterogeneous material into homogenous fuel products. This research assessed the ability of slow pyrolysis to convert three waste streams, composed of fibre residues contaminated with different plastic mixtures, into char and tarry phase products at three different temperatures (300, 425 and 550 °C). The products were characterised in terms of mass yield, higher heating value (HHV) and gross energy conversion (EC). Significant amounts of hydrocarbon plastics in the feed materials increased the calorific values of the char (up to 32.9 MJ/kg) and tarry phase (up to 42.8 MJ/kg) products, comparable to high volatile bituminous A coal and diesel respectively. For all three waste streams converted at 300 °C, the majority of the energy in the feedstock was recovered in the char product (>80%), while deoxygenation of fibre component resulted in char with increased calorific value (up to 31.6 MJ/kg) being produced. Pyrolysis at 425 °C for two of the waste streams containing significant amounts of plastic produced both a valuable char and tarry phase, which resulted in an EC greater than 74%. Full conversion of plastic at 550 °C increased the tarry phase yield but dramatically decreased the char HHV. The influence of temperature on product yield and HHV was discussed based on the pyrolysis mechanisms and in relation to the plastic composition of the waste streams.

Geochemical characterization of the hydrous pyrolysis products from a recent cyanobacteria-dominated microbial mat

Energy Technology Data Exchange (ETDEWEB)

Franco, N.; Mendoça-Filho, J.G.; Silva, T.F.; Stojanovic, K.; Fontana, L.F.; Carvalhal-Gomes, S.B.V.; Silva, F.S.; Furukawa, G.G.

2016-07-01

Hydrous pyrolysis experiments were performed on a recent microbial mat sample from Lagoa Vermelha, Brazil, to determine whether crude oil can be generated and expelled during artificial maturation of the Organic Matter (OM). The experiments were conducted at 280ºC, 330ºC and 350ºC during 20h. Two types of liquid pyrolysis products, assigned as free oil and bitumen, were isolated and analyzed. Free oil represents free organic phase released by hydrous pyrolysis, whereas bitumen was obtained by extraction from the solid pyrolysis residue with dichloromethane. Changes in the OM maturity were determined using Rock-Eval parameters and biomarker maturity ratios of original sample and pyrolysis products. Biomarker compositions of original sample extract and liquid pyrolysates were used for determination of dominant bacterial source. The yields of free oil and bitumen showed that a microbial mat OM has a high liquid hydrocarbons generation potential. Rock-Eval maturity parameters, biopolymer and biomarker compositions indicate a significant increase of the OM maturity during hydrous pyrolysis. At 280ºC the release of free, adsorbed and occluded compounds was observed; however, without a cracking of the OM. At 330ºC the generation of bitumen and free oil is mostly related to the OM cracking. The highest yield of free oil was recorded at this temperature. Distribution of biomarkers in the extract of original sample and liquid pyrolysates confirms cyanobacteria-dominated microbial mats, whereas the identification of long chain n-alkane series, with maximum at C26, and prominent C30 hop-17(21)-ene additionally suggest the presence of sulfate reducing bacteria. (Author)

Thermogravimetric characteristics of typical municipal solid waste fractions during co-pyrolysis.

Science.gov (United States)

Zhou, Hui; Long, YanQiu; Meng, AiHong; Li, QingHai; Zhang, YanGuo

2015-04-01

The interactions of nine typical municipal solid waste (MSW) fractions during pyrolysis were investigated using the thermogravimetric analyzer (TGA). To compare the mixture results with the calculation results of superposition of single fractions quantitatively, TG overlap ratio was introduced. There were strong interactions between orange peel and rice (overlap ratio 0.9736), and rice and poplar wood (overlap ratio 0.9774). The interactions of mixture experiments postponed the peak and lowered the peak value. Intense interactions between PVC and rice, poplar wood, tissue paper, wool, terylene, and rubber powder during co-pyrolysis were observed, and the pyrolysis at low temperature was usually promoted. The residue yield was increased when PVC was blended with rice, poplar wood, tissue paper, or rubber powder; while the residue yield was decreased when PVC was blended with wool. Copyright © 2014 Elsevier Ltd. All rights reserved.

The Search for Hesperian Organic Matter on Mars: Pyrolysis Studies of Sediments Rich in Sulfur and Iron.

Science.gov (United States)

Lewis, James M T; Najorka, Jens; Watson, Jonathan S; Sephton, Mark A

2018-04-01

Jarosite on Mars is of significant geological and astrobiological interest, as it forms in acidic aqueous conditions that are potentially habitable for acidophilic organisms. Jarosite can provide environmental context and may host organic matter. The most common extraction technique used to search for organic compounds on the surface of Mars is pyrolysis. However, thermal decomposition of jarosite releases oxygen into pyrolysis ovens, which degrades organic signals. Jarosite has a close association with the iron oxyhydroxide goethite in many depositional/diagenetic environments. Hematite can form by dehydration of goethite or directly from jarosite under certain aqueous conditions. Goethite and hematite are significantly more amenable than jarosite for pyrolysis experiments employed to search for organic matter. Analysis of the mineralogy and organic chemistry of samples from a natural acidic stream revealed a diverse response for organic compounds during pyrolysis of goethite-rich layers but a poor response for jarosite-rich or mixed jarosite-goethite samples. Goethite units that are associated with jarosite, but do not contain jarosite themselves, should be targeted for organic detection pyrolysis experiments on Mars. These findings are extremely timely, as exploration targets for Mars Science Laboratory include Vera Rubin Ridge (formerly known as "Hematite Ridge"), which may have formed from goethite precursors. Key Words: Mars-Pyrolysis-Jarosite-Goethite-Hematite-Biosignatures. Astrobiology 18, 454-464.

Pyrolysis model for an alpha waste incinerator prototype

International Nuclear Information System (INIS)

Orloff, D.I.

1978-01-01

The development of a theoretical model of the pyrolysis stage of an SRL prototype alpha waste incinerator is discussed. Pyrolysis rates for single component porous beds of Teflon (Registered trademark of Du Pont) and natural rubber have been measured on a bench-scale furnace. Experimental pyrolysis rates compare favorably to the predictions of a quasi-steady regression model. In addition, the pyrolysis rate is shown to be a weak function of the thermal diffusivity of the porous polymer bed. As a consequence, pyrolysis is controlled by thermal degradation kinetics rather than by diffusion or conduction

Pyrolysis of a waste from the grinding of scrap tyres.

Science.gov (United States)

Fernández, A M; Barriocanal, C; Alvarez, R

2012-02-15

The fibres that are used to reinforce tyres can be recovered as a waste in the process of grinding of scrap tyres. In this paper beneficiation through pyrolysis is studied since the fibres are made up of polymers with a small amount of rubber because the latter is difficult to separate. The experiments were performed at three temperatures (400, 550 and 900°C) in a horizontal oven. The three products - gas, oil and char - obtained from the pyrolysis were investigated. The composition of the gas was analyzed by means of gas chromatography. The oil was studied by gas chromatography and infrared spectroscopy. The char porous structure was determined by N(2) adsorption. In addition, the topography of the chars was studied by means of scanning electron microscopy (SEM). The products resulting from the pyrolysis of the fibres were compared with those obtained from scrap rubber. Copyright © 2011 Elsevier B.V. All rights reserved.

Exploratory studies on fast pyrolysis oil upgrading

NARCIS (Netherlands)

Mahfud, Farchad Husein

2007-01-01

Pyrolysis oil is a dark brown liquid which can be produced in high yield from different kind of biomass sources by means of fast pyrolysis. Pyrolysis oil is considered as a promising second generation energy carrier and may play an important role in the future of "biobased economies". The energy

Production and characterization of bio-oil from catalytic biomass pyrolysis

Directory of Open Access Journals (Sweden)

Antonakou Eleni V.

2006-01-01

Full Text Available Biomass flash pyrolysis is a very promising thermochemical process for the production of bio-fuels and/or chemicals. However, large-scale applications are still under careful consideration, because of the high bio-liquid upgrading cost. In this paper the production of bio-liquids from biomass flash pyrolysis in a single stage catalytic process is being investigated using a novel once through fluid bed reactor. This biomass pyrolysis unit was constructed in Chemical Process Engineering Research Institute and comprises of a catalyst regenerator, a biomass-vibrating hopper, a fluidization reactor (that consists of an injector and a riser reactor, a product stripper along with a hot cyclone and a filter housing and finally a product condensation/recovery section. The unit can process up to 20 g/min. of biomass (50-800 mm and can circulate up to 300 g/min. of catalyst or inert material. The experiments performed in the pilot plant showed that the unit operates without problems and with satisfactory mass balances in a wide range of experimental conditions both in the absence and presence of catalyst. With the incorporation of an FCC catalyst in the pyrolysis, the physical properties of the bio-oil produced changed, while more stable bio-oil was produced. .

Biomass pyrolysis for chemicals

Energy Technology Data Exchange (ETDEWEB)

De Wild, P.

2011-07-15

The problems associated with the use of fossil fuels demand a transition to renewable sources (sun, wind, water, geothermal, biomass) for materials and energy where biomass provides the only renewable source for chemicals. In a biorefinery, biomass is converted via different technologies into heat, power and various products. Here, pyrolysis (thermal degradation without added oxygen) of lignocellulosic biomass can play an important role, because it leads to an array of useful chemicals. Examples are furfural and acetic acid from hemicellulose, levoglucosan from cellulose and phenols and biochar from lignin. Since the three major biomass polymers hemicellulose, cellulose and lignin possess dissimilar thermal stabilities and reactivities, type and amount of degradation products are tunable by proper selection of the pyrolysis conditions. To determine if step-wise pyrolysis would be suitable for the production of chemicals, staged degasification of lignocellulosic biomass was studied. Due to limited yields, a hot pressurized water pre-treatment (aquathermolysis) followed by pyrolysis was subsequently developed as an improved version of a staged approach to produce furfural and levoglucosan from the carbohydrate fraction of the biomass. Lignin is the only renewable source for aromatic chemicals. Lignocellulosic biorefineries for bio-ethanol produce lignin as major by-product. The pyrolysis of side-streams into valuable chemicals is of prime importance for a profitable biorefinery. To determine the added-value of lignin side-streams other than their use as fuel for power, application research including techno-economic analysis is required. In this thesis, the pyrolytic valorisation of lignin into phenols and biochar was investigated and proven possible.

Thermal and catalytic pyrolysis of plastic waste

Directory of Open Access Journals (Sweden)

Débora Almeida

2016-02-01

Full Text Available Abstract The amount of plastic waste is growing every year and with that comes an environmental concern regarding this problem. Pyrolysis as a tertiary recycling process is presented as a solution. Pyrolysis can be thermal or catalytical and can be performed under different experimental conditions. These conditions affect the type and amount of product obtained. With the pyrolysis process, products can be obtained with high added value, such as fuel oils and feedstock for new products. Zeolites can be used as catalysts in catalytic pyrolysis and influence the final products obtained.

Fuels Combustion Research: Supercritical Fuel Pyrolysis

National Research Council Canada - National Science Library

Glassman, Irvin

2001-01-01

.... The focus during the subject period was directed to understanding the pyrolysis and combustion of endothermic fuels under subcritical conditions and the pyrolysis of these fuels under supercritical conditions...

Fuels Combustion Research: Supercritical Fuel Pyrolysis

National Research Council Canada - National Science Library

Glassman, Irvin

2000-01-01

.... The focus during the subject period was directed to understanding the pyrolysis and combustion of endothermic fuels under subcritical conditions and the pyrolysis of these fuels under supercritical conditions...

Flash pyrolysis of linseed (Linum usitatissimum L.) for production of liquid fuels

Energy Technology Data Exchange (ETDEWEB)

Acikgoz, C. [Department of Chemical Technology, Bilecik Higher Vocational School, GueluembeCampus, Anadolu University, 11030 Bilecik (Turkey); Kockar, O.M. [Department of Chemical Engineering, Faculty of Engineering and Architecture, iki Eyluel Campus, Anadolu University, 26470 Eskisehir (Turkey)

2007-03-15

Flash pyrolysis experiments of linseed (Linum usitatissimum L.) were performed in a tubular transport reactor at atmospheric pressure under nitrogen atmosphere. The effects of pyrolysis temperature and particle size on the yields of products were investigated with the sweep gas flow rate of 100 cm{sup 3} min{sup -1}. The temperature of pyrolysis and particle size were varied in the ranges 400-700 C and 0.6 mm < D{sub p} < 1.25 mm, 1.25 mm < D{sub p} < 1.8 mm, D{sub p} > 1.8 mm, respectively. The maximum oil yield of 68.8% was obtained at a pyrolysis temperature of 550 C, and the particle size of D{sub p} > 1.8 mm. The char and liquid product were analyzed to determine their elemental composition and calorific value. In particular, the chemical composition of the oil was investigated using chromatographic and spectroscopic techniques ({sup 1}H NMR, IR, column chromatography and GC). The chemical characterization has shown that the oil obtained from linseed can be used as a renewable fuel and chemical feedstock. (author)

The catalytic cracking mechanism of lignite pyrolysis char on tar

International Nuclear Information System (INIS)

Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

2017-01-01

The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

Thermal and catalytic pyrolysis of a mixture of plastics from small waste electrical and electronic equipment (WEEE).

Science.gov (United States)

Santella, Chiara; Cafiero, Lorenzo; De Angelis, Doina; La Marca, Floriana; Tuffi, Riccardo; Vecchio Ciprioti, Stefano

2016-08-01

Pyrolysis seems a promising route for recycling of heterogeneous, contaminated and additives containing plastics from waste electrical and electronic equipment (WEEE). This study deals with the thermal and catalytic pyrolysis of a synthetic mixture containing real waste plastics, representative of polymers contained in small WEEE. Two zeolite-based catalysts were used at 400°C: HUSY and HZSM-5 with a high silica content, while three different temperatures were adopted for the thermal cracking: 400, 600 and 800°C. The mass balance showed that the oil produced by pyrolysis is always the main product regardless the process conditions selected, with yields ranging from 83% to 93%. A higher yield was obtained when pyrolysis was carried out with HZSM-5 at 400°C and without catalysts, but at 600 and 800°C. Formation of a significant amount of solid residue (about 13%) is observed using HUSY. The oily liquid product of pyrolysis, analysed by GC-MS and GC-FID, as well as by elemental analysis and for energy content, appeared lighter, less viscous and with a higher concentration of monoaromatics under catalytic condition, if compared to the liquid product derived from thermal degradation at the same temperature. HZSM-5 led to the production of a high yield of styrene (17.5%), while HUSY favoured the formation of ethylbenzene (15%). Energy released by combustion of the oil was around 39MJ/kg, thus suggesting the possibility to exploit it as a fuel, if the recovery of chemical compounds could not be realised. Elemental and proximate analysis of char and GC-TCD analysis of the gas were also performed. Finally, it was estimated to what extent these two products, showing a relevant ability to release energy, could fulfil the energy demand requested in pyrolysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluating the effect of potassium on cellulose pyrolysis reaction kinetics

International Nuclear Information System (INIS)

Trendewicz, Anna; Evans, Robert; Dutta, Abhijit; Sykes, Robert; Carpenter, Daniel; Braun, Robert

2015-01-01

This paper proposes modifications to an existing cellulose pyrolysis mechanism in order to include the effect of potassium on product yields and composition. The changes in activation energies and pre-exponential factors due to potassium were evaluated based on the experimental data collected from pyrolysis of cellulose samples treated with different levels of potassium (0–1% mass fraction). The experiments were performed in a pyrolysis reactor coupled to a molecular beam mass spectrometer (MBMS). Principal component analysis (PCA) performed on the collected data revealed that cellulose pyrolysis products could be divided into two groups: anhydrosugars and other fragmentation products (hydroxyacetaldehyde, 5-hydroxymethylfurfural, acetyl compounds). Multivariate curve resolution (MCR) was used to extract the time resolved concentration score profiles of principal components. Kinetic tests revealed that potassium apparently inhibits the formation of anhydrosugars and catalyzes char formation. Therefore, the oil yield predicted at 500 ° C decreased from 87.9% from cellulose to 54.0% from cellulose with 0.5% mass fraction potassium treatment. The decrease in oil yield was accompanied by increased yield of char and gases produced via a catalyzed dehydration reaction. The predicted char and gas yield from cellulose were 3.7% and 8.4%, respectively. Introducing 0.5% mass fraction potassium treatment resulted in an increase of char yield to 12.1% and gas yield to 33.9%. The validation of the cellulose pyrolysis mechanism with experimental data from a fluidized-bed reactor, after this correction for potassium, showed good agreement with our results, with differences in product yields of up to 5%

Catalytic partial oxidation of pyrolysis oils

Science.gov (United States)

Rennard, David Carl

2009-12-01

This thesis explores the catalytic partial oxidation (CPO) of pyrolysis oils to syngas and chemicals. First, an exploration of model compounds and their chemistries under CPO conditions is considered. Then CPO experiments of raw pyrolysis oils are detailed. Finally, plans for future development in this field are discussed. In Chapter 2, organic acids such as propionic acid and lactic acid are oxidized to syngas over Pt catalysts. Equilibrium production of syngas can be achieved over Rh-Ce catalysts; alternatively mechanistic evidence is derived using Pt catalysts in a fuel rich mixture. These experiments show that organic acids, present in pyrolysis oils up to 25%, can undergo CPO to syngas or for the production of chemicals. As the fossil fuels industry also provides organic chemicals such as monomers for plastics, the possibility of deriving such species from pyrolysis oils allows for a greater application of the CPO of biomass. However, chemical production is highly dependent on the originating molecular species. As bio oil comprises up to 400 chemicals, it is essential to understand how difficult it would be to develop a pure product stream. Chapter 3 continues the experimentation from Chapter 2, exploring the CPO of another organic functionality: the ester group. These experiments demonstrate that equilibrium syngas production is possible for esters as well as acids in autothermal operation with contact times as low as tau = 10 ms over Rh-based catalysts. Conversion for these experiments and those with organic acids is >98%, demonstrating the high reactivity of oxygenated compounds on noble metal catalysts. Under CPO conditions, esters decompose in a predictable manner: over Pt and with high fuel to oxygen, non-equilibrium products show a similarity to those from related acids. A mechanism is proposed in which ethyl esters thermally decompose to ethylene and an acid, which decarbonylates homogeneously, driven by heat produced at the catalyst surface. Chapter 4

Coal pyrolysis under hydrogen-rich gases

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

1998-04-01

To improve the economy of the pyrolysis process by reducing the hydrogen cost, it is suggested to use cheaper hydrogen-rich gases such as coke-oven gas (COG) or synthesis gas (SG) instead of pure hydrogen. The pyrolysis of Chinese Xianfeng lignite which was carried out with real COG and SG at 3-5 MPa, a final temperature of 650{degree}C and a heating rate of 5{degree}C/min in a 10g fixed-bed reactor is compared with coal pyrolysis with pure hydrogen and nitrogen under the same conditions. The results indicate that compared with hydropyrolysis at the same total pressure, the total conversion and tar yields from coal pyrolysis with COG and SG decreases while the unwanted water increases. However, at the same H{sub 2} partial pressure, the tar yields and yields of BBTX, PCX and naphthalene from the pyrolysis of coal with COG and SG are all significantly higher than those of hydropyrolysis. Therefore, it is possible to use COG and SG instead of pure hydrogen. 8 refs., 3 figs., 6 tabs.

Influence of Oxychlorine Phases During the Pyrolysis of Organic Molecules: Implications for the Quest of Organics on Mars with the SAM Experiment Onboard the Curiosity Rover

Science.gov (United States)

Millan, M.; Szopa, C.; Buch, A.; Belmahdi, I.; Glavin, D. P.; Freissinet, C.; Eigenbrode, J. L.; Archer, P. D., Jr,; Sutter, B.; Mahaffy, P.

2017-01-01

One among the main objectives of the Sample Analysis at Mars (SAM) experiment is the in situ molecular analysis of gases evolving from solid samples heated up to approximately 850 degrees Centigrade, and collected by Curiosity on Mars surface/sub-surface in Gale crater. With this aim, SAM uses a gas-chromatograph coupled to a quadrupole mass spectrometer (GC-QMS) devoted to separate, detect and identify both volatile inorganic and organic compounds. SAM detected chlorinated organic molecules produced in evolved gas analysis (EGA) experiments. Several of these were also detected by the Viking experiments in 1976. SAM also detected oxychlorine compounds that were present at the Phoenix landing site. The oxychlorines may be prevelant over much of the martian surface. The C1 to C3 aliphatic chlorohydrocarbons (chloromethane and di- and trichloromethane) detected by SAM were attributed to reaction products occurring between the oxychlorines phases and the organic compounds coming from SAM instrument background. But SAM also showed the presence of a large excess of chlorobenzene and C2 to C4 dichloroalkanes among the volatile species released by the Cumberland sample of the Sheepbed mudstone. For the first time in the history of the Mars exploration, this proved the presence of Mars indigenous organic material at the Mars' surface. However, the identification of the precursor organic compounds of these chlorohydrocarbons is difficult due to the complexity of the reactions occurring during the sample pyrolysis. Laboratory pyrolysis experiments have demonstrated that oxychlorines phases such as perchlorates and chlorates, decomposed into dioxygen and volatile chlorine bearing molecules (HCl and/or Cl2) during the pyrolysis. These chemical species can then react with the organic molecules present in the martian solid samples through oxidation, chlorination and oxychlorination processes.

Mass spectrometric studies of fast pyrolysis of cellulose

Energy Technology Data Exchange (ETDEWEB)

Degenstein, John; Hurt, Matt; Murria, Priya; Easton, McKay; Choudhari, Harshavardhan; Yang, Linan; Riedeman, James; Carlsen, Mark; Nash, John; Agrawal, Rakesh; Delgass, W.; Ribeiro, Fabio; Kenttämaa, Hilkka

2015-01-01

A fast pyrolysis probe/linear quadrupole ion trap mass spectrometer combination was used to study the primary fast pyrolysis products (those that first leave the hot pyrolysis surface) of cellulose, cellobiose, cellotriose, cellotetraose, cellopentaose, and cellohexaose, as well as of cellobiosan, cellotriosan, and cellopentosan, at 600°C. Similar products with different branching ratios were found for the oligosaccharides and cellulose, as reported previously. However, identical products (with the exception of two) with similar branching ratios were measured for cellotriosan (and cellopentosan) and cellulose. This result demonstrates that cellotriosan is an excellent small-molecule surrogate for studies of the fast pyrolysis of cellulose and also that most fast pyrolysis products of cellulose do not originate from the reducing end. Based on several observations, the fast pyrolysis of cellulose is suggested to initiate predominantly via two competing processes: the formation of anhydro-oligosaccharides, such as cellobiosan, cellotriosan, and cellopentosan (major route), and the elimination of glycolaldehyde (or isomeric) units from the reducing end of oligosaccharides formed from cellulose during fast pyrolysis.

Catalytic Hydrotreatment of Fast Pyrolysis Oil: Model Studies on Reaction Pathways for the Carbohydrate Fraction

OpenAIRE

Wildschut, J.; Arentz, J.; Rasrendra, C. B.; Venderbosch, R. H.; Heeres, H. J.

2009-01-01

Fast pyrolysis oil can be upgraded by a catalytic hydrotreatment (250-400 degrees C, 100-200 bar) using heterogeneous catalysts such as Ru/C to hydrocarbon-like products that can serve as liquid transportation fuels. Insight into the complex reaction pathways of the various component fractions during hydrotreatment is desirable to reduce the formation of by-products such as char and gaseous components. This paper deals with the catalytic hydrotreatment of representative model components for t...

Influence of Pyrolysis Parameters on the Performance of CMSM

Directory of Open Access Journals (Sweden)

Marta C. Campo

2009-01-01

Full Text Available Carbon hollow fiber membranes have been prepared by pyrolysis of a P84/S-PEEK blend. Proximate analysis of the precursor was performed using thermogravimetry (TGA, and a carbon yield of approximately 40% can be obtained. This study aimed at understanding the influence of pyrolysis parameters—end temperature, quenching effect, and soaking time—on the membrane properties. Permeation experiments were performed with N2, He, and CO2. Scanning electron microscopy (SEM has been done for all carbon hollow fibers. The highest permeances were obtained for the membrane submitted to an end temperature of 750°C and the highest ideal selectivities for an end temperature of 700°C. In both cases, the membranes were quenched to room temperature.

Vacuum pyrolysis of waste tires with basic additives

International Nuclear Information System (INIS)

Zhang Xinghua; Wang Tiejun; Ma Longlong; Chang Jie

2008-01-01

Granules of waste tires were pyrolyzed under vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na 2 CO 3 , NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 deg. C to 600 deg. C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 deg. C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 deg. C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) ∼205 deg. C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt%, which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na 2 CO 3 addition. Pyrolysis gas was mainly composed of H 2 , CO, CH 4 , CO 2 , C 2 H 4 and C 2 H 6 . Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher

Chemical recycling of mixed waste plastics by selective pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Tatsumoto, K.; Meglen, R.; Evans, R. [National Renewable Energy Laboratory, Golden, CO (United States)

1995-05-01

The goal of this work is to use selective pyrolysis to produce high-value chemicals from waste plastics mixtures. Selectivity is achieved by exploiting differences in reaction rates, catalysis, and coreactants. Target wastes are molecular mixtures such as; blends or composites, or mixtures from manufactured products such as; carpets and post-consumer mixed-plastic wastes. The experimental approach has been to use small-scale experiments using molecular beam mass spectrometry (MBMS), which provides rapid analysis of reaction products and permits rapid screening of process parameters. Rapid screening experiments permit exploration of many potential waste stream applications for the selective pyrolysis process. After initial screening, small-scale, fixed-bed and fluidized-bed reactors are used to provide products for conventional chemical analysis, to determine material balances, and to test the concept under conditions that will be used at a larger scale. Computer assisted data interpretation and intelligent chemical processing are used to extract process-relevant information from these experiments. An important element of this project employs technoeconomic assessments and market analyses of durables, the availability of other wastes, and end-product uses to identify target applications that have the potential for economic success.

Influence of fast pyrolysis temperature on biochar labile fraction and short-term carbon loss in a loamy soil

DEFF Research Database (Denmark)

Bruun, Esben; Hauggaard-Nielsen, Henrik; Ibrahim, Norazana

2011-01-01

Production of bio-oil, gas and biochar from pyrolysis of biomass is considered a promising technology for combined production of bioenergy and recalcitrant carbon (C) suitable for sequestration in soil. Using a fast pyrolysis centrifuge reactor (PCR) the present study investigated the relation...... between fast pyrolysis of wheat straw at different reactor temperatures and the short-term degradability of biochar in soil. After 115 days incubation 3–12% of the added biochar-C had been emitted as CO2. On average, 90% of the total biochar-C loss occurred within the first 20 days of the experiment......, emphasizing the importance of knowing the biochar labile fraction when evaluating a specific biochars C sequestration potential. The pyrolysis temperature influenced the outputs of biochar, bio-oil and syngas significantly, as well as the stability of the biochar produced. Contrary to slow pyrolysis a fast...

Effects of smectite on the oil-expulsion efficiency of the Kreyenhagen Shale, San Joaquin Basin, California, based on hydrous-pyrolysis experiments

Science.gov (United States)

Lewan, Michael D.; Dolan, Michael P.; Curtis, John B.

2014-01-01

illite. As a result, illitization only reaches 35% to 40% at 310°C for 72 hr and remains unchanged to 365°C for 72 hr. Bitumen generation before or during early illitization in these experiments emphasizes the importance of knowing when and to what degree illitization occurs in natural maturation of a smectite-rich source rock to determine its expulsion efficiency. Complete illitization prior to bitumen generation is common for Paleozoic source rocks (e.g., Woodford Shale and Retort Phosphatic Shale Member of the Phosphoria Formation), and expulsion efficiencies can be determined on immature samples by hydrous pyrolysis. Conversely, smectite is more common in Cenozoic source rocks like the Kreyenhagen Shale, and expulsion efficiencies determined by hydrous pyrolysis need to be made on samples that reflect the level of illitization at or near bitumen generation in the subsurface.

Pyrolysis model for an alpha waste incinerator prototype

International Nuclear Information System (INIS)

Orloff, D.I.

1979-01-01

The development of a theoretical model of the pyrolysis stage of a Savnnah River Laboratory prototype alpha waste incinerator is discussed. pyrolysis rates for single-component porous bed of Teflon (registered trademark of Du Pont de Nemours and Co.) have been measured on a bench-scale furnace. Experimental pyrolysis rates compare favorably to the predictions of a quasisteady regression model. In addition, the pyrolysis rate is shown to be a weak function of the thermal diffusivity of the porous polymer bed. 13 refs

Pyrolysis of flax straw: Characterization of char, liquid, and gas as fuel

Science.gov (United States)

Tushar, Mohammad Shahed Hasan Khan

The demand for energy continues to outstrip its supply and necessitates the development of renewable energy options. Biomass has been recognized as a major renewable energy source to supplement the declining fossil fuel source of energy. It is the most popular form of renewable energy and, currently, biofuel production is becoming more promising. Being carbon neutral, readily available, and low in sulphur content makes biomass a very promising source of renewable energy. In the present research, both the isothermal and non-isothermal pressurized pyrolysis of flax straw is studied for the first time. In case of isothermal pyrolysis, the influence of pyrolysis temperature and reaction time on char yield and morphology was investigated. The applied pyrolysis temperature was varied between 300 and 500°C. The reaction time was varied from 15 to 60 min. The char yield was found to decrease as pyrolysis temperature and reaction time increased. The char structure and surface morphology were thoroughly investigated by means of x-ray diffraction (XRD), temperature-programmed oxidation (TPO), and scanning electron microscopy (SEM). The degree of porosity and graphitization increased as pyrolysis temperature and time increased. In fact, the experiment performed at 500°C for 1h duration did not yield any char; only residual ash could be obtained. The TPO studies on the char samples corroborated the XRD findings and showed the presence of two types of carbon, namely, amorphous filamentous carbon and graphitic carbon. A thermogravimetric analysis (TGA) of the char was performed to gain an understanding of combustion kinetics and reactivity. It implied that the reactivity of the char decreases as temperature increases, and this finding is well supported by the TPO, TGA, SEM, and XRD characterization data. Furthermore, an empirical global model was devised based on the power law to estimate activation energy and other kinetic parameters. For the non-isothermal pressurized

Pyrolysis of Medium Density Fiberboard (MDF) wastes in a screw reactor

International Nuclear Information System (INIS)

Ferreira, Suelem Daiane; Altafini, Carlos Roberto; Perondi, Daniele; Godinho, Marcelo

2015-01-01

Highlights: • Medium Density Fiberboard wastes were pirolized in an auger reactor. • Experiments were carried out at two reaction temperatures and three solid residence times. • Yields were influenced by pyrolysis temperature, as well as by solid residence time. • Higher temperature produced more bio-oil rather than char generation. • Chars superficial area were compatibles with those of commercial activated carbons. - Abstract: Medium Density Fiberboard (MDF) wastes were undergoes via a thermal treatment through of a pyrolysis process. Pyrolysis was carried out in a pilot scale reactor with screw conveyor at two reaction temperatures (450 and 600 °C) and, for each one, three solid residence times (9, 15 and 34 min) were evaluated. Products (char/bio-oil/fuel gas) of the pyrolysis process were characterized and quantified. Results revealed that the products yields were influenced by pyrolysis temperature, as well as by solid residence time. Char yield ranged between 17.3 and 39.7 (wt.%), the bio-oil yield ranged between 23.9 and 40.0 (wt.%), while the fuel gas yield ranged between 34.6 and 50.7 (wt.%). The samples surface area at 450 and 600 °C in 15-min residence time were surprisingly high, 415 and 593 m 2 g −1 , respectively, which are compatible with the superficial area of commercial activated carbons. Energetic efficiency of process was estimated from energetic content present in the reaction products and the energetic content of MDF wastes, and the following results were obtained: 41.4% (fuel gas), 35.5% (char) and 29.2% (bio-oil). The contribution of this work is the development of a detailed study of the MDF pyrolysis in a pilot reactor with screw conveyor that supports the biorefineries concept

Rates and Mechanisms of Oil Shale Pyrolysis: A Chemical Structure Approach

Energy Technology Data Exchange (ETDEWEB)

Fletcher, Thomas; Pugmire, Ronald

2015-01-01

Three pristine Utah Green River oil shale samples were obtained and used for analysis by the combined research groups at the University of Utah and Brigham Young University. Oil shale samples were first demineralized and the separated kerogen and extracted bitumen samples were then studied by a host of techniques including high resolution liquid-state carbon-13 NMR, solid-state magic angle sample spinning 13C NMR, GC/MS, FTIR, and pyrolysis. Bitumen was extracted from the shale using methanol/dichloromethane and analyzed using high resolution 13C NMR liquid state spectroscopy, showing carbon aromaticities of 7 to 11%. The three parent shales and the demineralized kerogens were each analyzed with solid-state 13C NMR spectroscopy. Carbon aromaticity of the kerogen was 23-24%, with 10-12 aromatic carbons per cluster. Crushed samples of Green River oil shale and its kerogen extract were pyrolyzed at heating rates from 1 to 10 K/min at pressures of 1 and 40 bar and temperatures up to 1000°C. The transient pyrolysis data were fit with a first-order model and a Distributed Activation Energy Model (DAEM). The demineralized kerogen was pyrolyzed at 10 K/min in nitrogen at atmospheric pressure at temperatures up to 525°C, and the pyrolysis products (light gas, tar, and char) were analyzed using 13C NMR, GC/MS, and FTIR. Details of the kerogen pyrolysis have been modeled by a modified version of the chemical percolation devolatilization (CPD) model that has been widely used to model coal combustion/pyrolysis. This refined CPD model has been successful in predicting the char, tar, and gas yields of the three shale samples during pyrolysis. This set of experiments and associated modeling represents the most sophisticated and complete analysis available for a given set of oil shale samples.

Reprint of: Pyrolysis technologies for municipal solid waste: A review

Energy Technology Data Exchange (ETDEWEB)

Chen, Dezhen, E-mail: chendezhen@tongji.edu.cn [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); Yin, Lijie; Wang, Huan [Thermal & Environmental Engineering Institute, Tongji University, Shanghai 200092 (China); He, Pinjing [State Key Laboratory of Pollution Control and Resource Reuse, College of Environmental Science and Engineering, Tongji University, Shanghai 200092 (China)

2015-03-15

Highlights: • MSW pyrolysis reactors, products and environmental impacts are reviewed. • MSW pyrolysis still has to deal with flue gas emissions and products’ contamination. • Definition of standardized products is suggested to formalize MSW pyrolysis technology. • Syngas is recommended to be the target product for single MSW pyrolysis technology. - Abstract: Pyrolysis has been examined as an attractive alternative to incineration for municipal solid waste (MSW) disposal that allows energy and resource recovery; however, it has seldom been applied independently with the output of pyrolysis products as end products. This review addresses the state-of-the-art of MSW pyrolysis in regards to its technologies and reactors, products and environmental impacts. In this review, first, the influence of important operating parameters such as final temperature, heating rate (HR) and residence time in the reaction zone on the pyrolysis behaviours and products is reviewed; then the pyrolysis technologies and reactors adopted in literatures and scale-up plants are evaluated. Third, the yields and main properties of the pyrolytic products from individual MSW components, refuse-derived fuel (RDF) made from MSW, and MSW are summarised. In the fourth section, in addition to emissions from pyrolysis processes, such as HCl, SO{sub 2} and NH{sub 3}, contaminants in the products, including PCDD/F and heavy metals, are also reviewed, and available measures for improving the environmental impacts of pyrolysis are surveyed. It can be concluded that the single pyrolysis process is an effective waste-to-energy convertor but is not a guaranteed clean solution for MSW disposal. Based on this information, the prospects of applying pyrolysis technologies to dealing with MSW are evaluated and suggested.

Desulfurized gas production from vertical kiln pyrolysis

Science.gov (United States)

Harris, Harry A.; Jones, Jr., John B.

1978-05-30

A gas, formed as a product of a pyrolysis of oil shale, is passed through hot, retorted shale (containing at least partially decomposed calcium or magnesium carbonate) to essentially eliminate sulfur contaminants in the gas. Specifically, a single chambered pyrolysis vessel, having a pyrolysis zone and a retorted shale gas into the bottom of the retorted shale zone and cleaned product gas is withdrawn as hot product gas near the top of such zone.

Biomass fast pyrolysis for bio-oil production in a fluidized bed reactor under hot flue atmosphere.

Science.gov (United States)

Li, Ning; Wang, Xiang; Bai, Xueyuan; Li, Zhihe; Zhang, Ying

2015-10-01

Fast pyrolysis experiments of corn stalk were performed to investigate the optimal pyrolysis conditions of temperature and bed material for maximum bio-oil production under flue gas atmosphere. Under the optimized pyrolysis conditions, furfural residue, xylose residue and kelp seaweed were pyrolyzed to examine their yield distributions of products, and the physical characteristics of bio-oil were studied. The best flow rate of the flue gas at selected temperature is obtained, and the pyrolysis temperature at 500 degrees C and dolomite as bed material could give a maximum bio-oil yield. The highest bio-oil yield of 43.3% (W/W) was achieved from corn stalk under the optimal conditions. Two main fractions were recovered from the stratified bio-oils: light oils and heavy oils. The physical properties of heavy oils from all feedstocks varied little. The calorific values of heavy oils were much higher than that of light oils. The pyrolysis gas could be used as a gaseous fuel due to a relatively high calorific value of 6.5-8.5 MJ/m3.

Effects of the cellulose, xylan and lignin constituents on biomass pyrolysis characteristics and bio-oil composition using the Simplex Lattice Mixture Design method

International Nuclear Information System (INIS)

Fan, Yongsheng; Cai, Yixi; Li, Xiaohua; Jiao, Lihua; Xia, Jisheng; Deng, Xiuli

2017-01-01

Highlights: • Simplex Lattice Mixture Design was firstly applied to study biomass pyrolysis process. • Interactions between the constituents had effects on the biomass pyrolysis behavior. • Biomass pyrolysis behavior can be predicted based on the ratios of three constituents. • Bio-oil composition was affected by the constituents and their pyrolysis products. - Abstract: In order to clarify the relationships between biomass pyrolysis mechanism and its main constituents. The effects of main constituents on biomass pyrolysis characteristics were firstly determined by thermo-gravimetric analysis based on the Simplex Lattice Mixture Design to investigate that whether the prediction of the pyrolysis behavior of a certain lignocellulosic biomass is possible when its main constituent contents are known. The results showed that there are constituent interactions in the pyrolysis process, which can be intuitively reflected through the change laws of kinetics parameters. The mathematical models for calculating kinetics values were established, and the models were proved to be valid for predicting lignocellulosic biomass pyrolysis behavior. In addition, the effects of biomass constituents on bio-oil compositions were explored by subsequent vacuum pyrolysis experiments. The xylan pyrolysis had a certain inhibitory effect on the pyrolysis of cellulose, and the pyrolysis products of lignin might promote the further decomposition of sugars from cellulose pyrolysis, while the interaction between xylan and lignin had a little effect on the bio-oil composition.

Catalytic pyrolysis of microalgae to high-quality liquid bio-fuels

NARCIS (Netherlands)

Babych, Igor V.; van der Hulst, M.; Lefferts, Leonardus; Moulijn, J.A.; Seshan, Kulathuiyer; O'Connor, P.

2011-01-01

The pyrolytic conversion of chlorella algae to liquid fuel precursor in presence of a catalyst (Na2CO3) has been studied. Thermal decomposition studies of the algae samples were performed using TGA coupled with MS. Liquid oil samples were collected from pyrolysis experiments in a fixed-bed reactor

Thermal behavior of the major constituents of some agricultural biomass residues during pyrolysis and combustion

Energy Technology Data Exchange (ETDEWEB)

Yaman, S.; Haykiri-Acma, H. [Istanbul Technical Univ., Istanbul (Turkey). Dept. of Chemical Engineering, Chemical and Metallurgical Engineering Faculty

2006-07-01

The importance of woody agricultural waste as a renewable energy source was discussed with reference to its low cost, abundance, and carbon dioxide neutrality. Direct combustion of biomass waste fuels is not recommended due to its low density, high moisture content and low calorific energy. Rather, thermal conversion processes such as pyrolysis, gasification or carbonization are preferred for biomass. The performance and the energy recovery potentials of these processes depend on the process conditions as well as the physical and chemical properties of the biomass species. Therefore, the structure and components of biomass must be known. In this study, agricultural biomass samples of almond shell, walnut shell, hazelnut shell, rapeseed, olive residue, and tobacco waste were first analytically treated to remove extractive matter to obtain extractive-free samples. Specific analytic procedures were then applied to biomass samples in order to isolate their individual biomass constituents such as lignin and holocellulose. Untreated biomass samples and their isolated constituents were exposed to non-isothermal pyrolysis and combustion processes in a thermogravimetric analyzer. Pyrolysis experiments were conducted under dynamic nitrogen atmospheres of 40 mL-min, while dynamic dry air atmosphere with the same flow rate was applied in the combustion experiments. The study showed that the pyrolysis and combustion characteristics of the biomass samples differed depending on their properties. Aliphatic and oxygen rich holocellulose and cellulose were found to be the reactive components in biomass. Lignin was more stable during thermal processes. When extractive matter from the biomass samples was removed, pyrolysis at lower temperatures was terminated. 10 refs., 4 tabs., 3 figs.

Thermal and kinetic behaviors of biomass and plastic wastes in co-pyrolysis

International Nuclear Information System (INIS)

Çepelioğullar, Özge; Pütün, Ayşe E.

2013-01-01

Graphical abstract: - Highlights: • Co-pyrolysis of biomass together with the plastic wastes in thermogravimetric analyzer. • Investigations into thermal and kinetic behaviors at high temperature regions. • Determination of the kinetic parameters. - Abstract: In this study, co-pyrolysis characteristics and kinetics of biomass-plastic blends were investigated. Cotton stalk, hazelnut shell, sunflower residue, and arid land plant Euphorbia rigida, were blended in definite ratio (1:1, w/w) with polyvinyl chloride (PVC) and polyethylene terephthalate (PET). Experiments were conducted with a heating rate of 10 °C min −1 from room temperature to 800 °C in the presence of N 2 atmosphere with a flow rate of 100 cm 3 min −1 . After thermal decomposition in TGA, a kinetic analysis was performed to fit thermogravimetric data and a detailed discussion of co-pyrolysis mechanism was achieved. Experimental results demonstrated that the structural differences between biomass and plastics directly affect their thermal decomposition behaviors. Biomass pyrolysis generally based on three main steps while plastic material’s pyrolysis mechanism resulted in two steps for PET and three steps for PVC. Also, the required activation energies needed to achieve the thermal degradation for plastic were found higher than the biomass materials. In addition, it can be concluded that the evaluation of plastic materials together with biomass created significant changes not only for the thermal behaviors but also for the kinetic behaviors

The use of design of experiments for the evaluation of the production of surface rich activated carbon from sewage sludge via microwave and conventional pyrolysis

International Nuclear Information System (INIS)

Simões dos Reis, Glaydson; Wilhelm, Michaela; Silva, Thamires Canuto de Almeida; Rezwan, Kurosch; Sampaio, Carlos Hoffmann; Lima, Eder Claudio; Guelli Ulson de Souza, Selene M.A.

2016-01-01

Highlights: • Using of DOE for preparation of AC by conventional and microwave pyrolysis. • The significant parameters in producing activated carbon were investigated. • Conventional pyrolysis AC had better textural development than microwave AC. • Temperature and holding time had significant influence on the S_B_E_T. • Reduction of production cost of activated carbon. - Abstract: Experimental design and response surface methodology were used for the preparation and comparison of activated carbon produced from sewage sludge by two types of pyrolysis: conventional furnace and microwave. The preparation method was performed following a full fractional factorial design (2"3), including pyrolysis temperature or power radiation, holding time and chemical activation agent, and specific surface area (S_B_E_T) of prepared activated carbon. The influence of these factors on the S_B_E_T of obtained carbon was investigated using an analysis of variance. Samples made by conventional pyrolysis showed overall higher S_B_E_T values than samples synthesised by the microwave method. The optimum parameters for the preparation of activated carbon using the conventional pyrolysis have been identified as: pyrolysis temperature of 500 °C, holding time of 15 min, and a ratio of ZnCl_2:sludge of 0.5. Microwave pyrolysis is found to be optimal when operating at 980 W for 12 min. Under these conditions, S_B_E_T values of 679 and 501 m"2g"−"1, respectively, have been obtained. The analysis of nitrogen adsorption/desorption isotherms revealed the presence of micro and mesopores in the activated carbon. The most important significant factor, according statistical analysis, in the variance in S_B_E_T for the conventional pyrolysis samples were the pyrolysis temperature and interaction between pyrolysis temperature, holding time and ratio of ZnCl_2:sludge were the most important factors. The highest impact parameters for the microwave method were found for the interaction

A Novel Energy-Efficient Pyrolysis Process: Self-pyrolysis of Oil Shale Triggered by Topochemical Heat in a Horizontal Fixed Bed

Science.gov (United States)

Sun, You-Hong; Bai, Feng-Tian; Lü, Xiao-Shu; Li, Qiang; Liu, Yu-Min; Guo, Ming-Yi; Guo, Wei; Liu, Bao-Chang

2015-02-01

This paper proposes a novel energy-efficient oil shale pyrolysis process triggered by a topochemical reaction that can be applied in horizontal oil shale formations. The process starts by feeding preheated air to oil shale to initiate a topochemical reaction and the onset of self-pyrolysis. As the temperature in the virgin oil shale increases (to 250-300°C), the hot air can be replaced by ambient-temperature air, allowing heat to be released by internal topochemical reactions to complete the pyrolysis. The propagation of fronts formed in this process, the temperature evolution, and the reaction mechanism of oil shale pyrolysis in porous media are discussed and compared with those in a traditional oxygen-free process. The results show that the self-pyrolysis of oil shale can be achieved with the proposed method without any need for external heat. The results also verify that fractured oil shale may be more suitable for underground retorting. Moreover, the gas and liquid products from this method were characterised, and a highly instrumented experimental device designed specifically for this process is described. This study can serve as a reference for new ideas on oil shale in situ pyrolysis processes.

Rapid habitability assessment of Mars samples by pyrolysis-FTIR

Science.gov (United States)

Gordon, Peter R.; Sephton, Mark A.

2016-02-01

Pyrolysis Fourier transform infrared spectroscopy (pyrolysis FTIR) is a potential sample selection method for Mars Sample Return missions. FTIR spectroscopy can be performed on solid and liquid samples but also on gases following preliminary thermal extraction, pyrolysis or gasification steps. The detection of hydrocarbon and non-hydrocarbon gases can reveal information on sample mineralogy and past habitability of the environment in which the sample was created. The absorption of IR radiation at specific wavenumbers by organic functional groups can indicate the presence and type of any organic matter present. Here we assess the utility of pyrolysis-FTIR to release water, carbon dioxide, sulfur dioxide and organic matter from Mars relevant materials to enable a rapid habitability assessment of target rocks for sample return. For our assessment a range of minerals were analyzed by attenuated total reflectance FTIR. Subsequently, the mineral samples were subjected to single step pyrolysis and multi step pyrolysis and the products characterised by gas phase FTIR. Data from both single step and multi step pyrolysis-FTIR provide the ability to identify minerals that reflect habitable environments through their water and carbon dioxide responses. Multi step pyrolysis-FTIR can be used to gain more detailed information on the sources of the liberated water and carbon dioxide owing to the characteristic decomposition temperatures of different mineral phases. Habitation can be suggested when pyrolysis-FTIR indicates the presence of organic matter within the sample. Pyrolysis-FTIR, therefore, represents an effective method to assess whether Mars Sample Return target rocks represent habitable conditions and potential records of habitation and can play an important role in sample triage operations.

Bio-oil production through pyrolysis of blue-green algae blooms (BGAB): Product distribution and bio-oil characterization

International Nuclear Information System (INIS)

Hu, Zhiquan; Zheng, Yang; Yan, Feng; Xiao, Bo; Liu, Shiming

2013-01-01

Pyrolysis experiments of blue-green algae blooms (BGAB) were carried out in a fixed-bed reactor to determine the effects of pyrolysis temperature, particle size and sweep gas flow rate on pyrolysis product yields and bio-oil properties. The pyrolysis temperature, particle size and sweep gas flow rate were varied in the ranges of 300–700 °C, below 0.25–2.5 mm and 50–400 mL min −1 , respectively. The maximum oil yield of 54.97% was obtained at a pyrolysis temperature of 500 °C, particle size below 0.25 mm and sweep gas flow rate of 100 mL min −1 . The elemental analysis and calorific value of the oil were determined, and the chemical composition of the oil was investigated using gas chromatography–mass spectroscopy (GC–MS) technique. The analysis of bio-oil composition showed that bio-oil from BGAB could be a potential source of renewable fuel with a heating value of 31.9 MJ kg −1 . - Highlights: ► Bio-oil production from pyrolysis of blue-green algae blooms in fixed bed reactor. ► Effects of pyrolysis conditions on product distribution were investigated. ► The maximum bio-oil yield reached 54.97 wt %. ► The bio-oil has high heating value and may be suitable as renewable fuel. ► Pyrolysis of algal biomass beneficial for energy recovery, eutrophication control

Optimization of process parameters in flash pyrolysis of waste tyres to liquid and gaseous fuel in a fluidized bed reactor

International Nuclear Information System (INIS)

Edwin Raj, R.; Robert Kennedy, Z.; Pillai, B.C.

2013-01-01

Highlights: ► Non-recyclable, hazards, under-utilized waste tyre was converted to useful fuel. ► Design of experiment was used to optimize the process parameters. ► Fuel compatibility for IC engines was tested by standard fuel testing procedures. ► Optimized process parameters were tested and the empirical model validated. - Abstract: Pyrolysis process offers solution to utilize huge quantity of worn out automobile tyres to produce fuel for energy needs. Shredded tyre wastes were subjected to pyrolysis at atmospheric pressure under inert gas atmosphere in a fluidized bed combustion setup. The shredded tyre particle size, the feed rate of the feed stock, and the pyrolysis temperature were varied systematically as per the designed experiment to study their influence on product yield. Maximizing the oil yield and subduing the gas and char yield is the objective to optimize the process parameters. A low pyrolysis temperature of 440 °C with low feed rate increases the residence time in the combustion reactor yielding maximum oil. The physical properties of raw pyrolysis oil, distilled oil and the evolved gases were done to find its suitability to utilize them as alternatives to the conventional fuels

Catalytic pyrolysis using UZM-39 aluminosilicate zeolite

Science.gov (United States)

Nicholas, Christpher P; Boldingh, Edwin P

2013-12-17

A new family of coherently grown composites of TUN and IMF zeotypes has been synthesized and show to be effective catalysts for catalytic pyrolysis of biomass. These zeolites are represented by the empirical formula. Na.sub.nM.sub.m.sup.n+R.sub.rQ.sub.qAl.sub1-xE.sub.xSi.sub.yO.s- ub.z where M represents zinc or a metal or metals from Group 1, Group 2, Group 3 or the lanthanide series of the periodic table, R is an A,.OMEGA.-dihalosubstituted paraffin such as 1,4-dibromobutane, Q is a neutral amine containing 5 or fewer carbon atoms such as 1-methylpyrrolidine and E is a framework element such as gallium. The process involves contacting a carbonaceous biomass feedstock with UZM-39 at pyrolysis conditions to produce pyrolysis gases comprising hydrocarbons. The catalyst catalyzes a deoxygenation reaction converting oxygenated hyrdocarbons into hydrocarbons removing the oxygen as carbon oxides and water. A portion of the pyrolysis gases is condensed to produce low oxygen biomass-derived pyrolysis oil.

Pyrolysis of rubber gloves in integral pyrolysis test plant

International Nuclear Information System (INIS)

Norasalwa Zakaria; Mohd Noor Muhd Yunus; Mohd Annuar Assadat Husain; Farid Nasir Ani

2010-01-01

Previously, pyrolysis of rubber gloves in laboratory study was described. In order to visualize the practical application of rubber gloves pyrolysis in terms of treating rubber gloves in medical waste, a new test plant was designed and constructed. The semi-continuous test plant was designed to accommodate rubber gloves that were not cut or shredded. The test plant has a capacity of 2kg/ hr and employed auxiliary fuel instead of the conventional electrical power for heating. The concept was based on moving bed reactor, but additional feature of sand jacket feature was also introduced in the design. Pyrolysis of the gloves was conducted at three temperatures, namely 350 degree Celsius, 400 degree Celsius and 450 degree Celsius. Oxygen presents inside of the reactor due to the combined effect of imperfect sealing and suction effect. This study addresses the performance of this test plant covering the time temperature profile, gas evolution profile and product yield. Comparison between the yield of the liquid, gas and char pyrolyzate was made against the laboratory study. It was found that the oil yield was less than the one obtained from bench scale study. Water formation was more pronounced. The presence of the oxygen also altered the tail gas composition but eliminate the sticky nature of solid residue, making it easier to handle. The chemical composition of the oil was determined and the main compounds in the oil were esters and phtalic acid. (author)

Using vacuum pyrolysis and mechanical processing for recycling waste printed circuit boards

International Nuclear Information System (INIS)

Long Laishou; Sun Shuiyu; Zhong Sheng; Dai Wencan; Liu Jingyong; Song Weifeng

2010-01-01

The constant growth in generation of waste printed circuit boards (WPCB) poses a huge disposal problem because they consist of a heterogeneous mixture of organic and metallic chemicals as well as glass fiber. Also the presence of heavy metals, such as Pb and Cd turns this scrap into hazardous waste. Therefore, recycling of WPCB is an important subject not only from the recovery of valuable materials but also from the treatment of waste. The aim of this study was to present a recycling process without negative impact to the environment as an alternative for recycling WPCB. In this work, a process technology containing vacuum pyrolysis and mechanical processing was employed to recycle WPCB. At the first stage of this work, the WPCB was pyrolyzed under vacuum in a self-made batch pilot-scale fixed bed reactor to recycle organic resins contained in the WPCB. By vacuum pyrolysis the organic matter was decomposed to gases and liquids which could be used as fuels or chemical material resources, however, the inorganic WPCB matter was left unaltered as solid residues. At the second stage, the residues obtained at the first stage were investigated to separate and recover the copper through mechanical processing such as crushing, screening, and gravity separation. The copper grade of 99.50% with recovery of 99.86% based on the whole WPCB was obtained. And the glass fiber could be obtained by calcinations in a muffle furnace at 600 deg. C for 10 min. This study had demonstrated the feasibility of vacuum pyrolysis and mechanical processing for recycling WPCB.

Multi-scale Multi-dimensional Imaging and Characterization of Oil Shale Pyrolysis

Science.gov (United States)

Gao, Y.; Saif, T.; Lin, Q.; Al-Khulaifi, Y.; Blunt, M. J.; Bijeljic, B.

2017-12-01

The microstructural evaluation of fine grained rocks is challenging which demands the use of several complementary methods. Oil shale, a fine-grained organic-rich sedimentary rock, represents a large and mostly untapped unconventional hydrocarbon resource with global reserves estimated at 4.8 trillion barrels. The largest known deposit is the Eocene Green River Formation in Western Colorado, Eastern Utah, and Southern Wyoming. An improved insight into the mineralogy, organic matter distribution and pore network structure before, during and after oil shale pyrolysis is critical to understanding hydrocarbon flow behaviour and improving recovery. In this study, we image Mahogany zone oil shale samples in two dimensions (2-D) using scanning electron microscopy (SEM), and in three dimensions (3-D) using focused ion beam scanning electron microscopy (FIB-SEM), laboratory-based X-ray micro-tomography (µCT) and synchrotron X-ray µCT to reveal a complex and variable fine grained microstructure dominated by organic-rich parallel laminations which are tightly bound in a highly calcareous and heterogeneous mineral matrix. We report the results of a detailed µCT study of the Mahogany oil shale with increasing pyrolysis temperature. The physical transformation of the internal microstructure and evolution of pore space during the thermal conversion of kerogen in oil shale to produce hydrocarbon products was characterized. The 3-D volumes of pyrolyzed oil shale were reconstructed and image processed to visualize and quantify the volume and connectivity of the pore space. The results show a significant increase in anisotropic porosity associated with pyrolysis between 300-500°C with the formation of micron-scale connected pore channels developing principally along the kerogen-rich lamellar structures.

Pyrolysis and reutilization of plant residues after phytoremediation of heavy metals contaminated sediments: For heavy metals stabilization and dye adsorption.

Science.gov (United States)

Gong, Xiaomin; Huang, Danlian; Liu, Yunguo; Zeng, Guangming; Wang, Rongzhong; Wei, Jingjing; Huang, Chao; Xu, Piao; Wan, Jia; Zhang, Chen

2018-04-01

This study aimed to investigate the effect of pyrolysis on the stabilization of heavy metals in plant residues obtained after phytoremediation. Ramie residues, being collected after phytoremediation of metal contaminated sediments, were pyrolyzed at different temperatures (300-700 °C). Results indicated that pyrolysis was effective in the stabilization of Cd, Cr, Zn, Cu, and Pb in ramie residues by converting the acid-soluble fraction of metals into residual form and decreasing the TCLP-leachable metal contents. Meanwhile, the reutilization potential of using the pyrolysis products generated from ramie residues obtained after phytoremediation as sorbents was investigated. Adsorption experiments results revealed that the pyrolysis products presented excellent ability to adsorb methylene blue (MB) with a maximum adsorption capacity of 259.27 mg/g. This study demonstrated that pyrolysis could be used as an efficient alternative method for stabilizing heavy metals in plant residues obtained after phytoremediation, and their pyrolysis products could be reutilized for dye adsorption. Copyright © 2018 Elsevier Ltd. All rights reserved.

Pyrolysis Recovery of Waste Shipping Oil Using Microwave Heating

Directory of Open Access Journals (Sweden)

Wan Adibah Wan Mahari

2016-09-01

Full Text Available This study investigated the use of microwave pyrolysis as a recovery method for waste shipping oil. The influence of different process temperatures on the yield and composition of the pyrolysis products was investigated. The use of microwave heating provided a fast heating rate (40 °C/min to heat the waste oil at 600 °C. The waste oil was pyrolyzed and decomposed to form products dominated by pyrolysis oil (up to 66 wt. % and smaller amounts of pyrolysis gases (24 wt. % and char residue (10 wt. %. The pyrolysis oil contained light C9–C30 hydrocarbons and was detected to have a calorific value of 47–48 MJ/kg which is close to those traditional liquid fuels derived from fossil fuel. The results show that microwave pyrolysis of waste shipping oil generated an oil product that could be used as a potential fuel.

Release of K, Cl, and S during Pyrolysis and Combustion of High-Chlorine Biomass

DEFF Research Database (Denmark)

Johansen, Joakim Myung; Jakobsen, Jon Geest; Frandsen, Flemming

2011-01-01

The release of critical ash-forming elements during the pyrolysis and combustion of corn stover has been investigated through controlled lab-scale experiments supported by multicomponent and multiphase thermodynamic equilibrium calculations. Fuel samples were treated under isothermal conditions...... ranging from 500 to 1150 °C, under both pyrolysis and combustion atmospheres. The volatilized material was quantified by means of mass balances based on char and ash elemental analysis, compared to a corresponding feedstock fuel analysis. Close relations between the observed K and Cl release are found...

Optimization of fuel recovery through the stepwise co-pyrolysis of palm shell and scrap tire

International Nuclear Information System (INIS)

Abnisa, Faisal; Wan Daud, Wan Mohd Ashri

2015-01-01

Highlights: • The co-pyrolysis of palm shell and scrap tire was studied. • The effect of stepwise co-pyrolysis temperature was investigated. • Co-pyrolysis successfully improved the quantity and quality of product yields. • Stepwise co-pyrolysis slightly increased oil and gas, and decreased char. • The co-pyrolysis of 50% biomass and 50% scrap tire is recommended. - Abstract: This study optimized the use of biomass waste to generate fuel through co-pyrolysis. In this paper, the effects of stepwise co-pyrolysis temperature and different ratios between palm shells and scrap tires in feedstock were studied to observe any improvements in the quantity and quality of the liquid yield and its byproduct. The ratio of palm shells and scrap tires varied at 100:0, 75:25, 50:50, 25:75, and 0:100. The experiment was conducted in a fixed-bed reactor. The study was divided into two scenarios. The first scenario was performed at the optimum temperature of 500 °C with a reaction time of 60 min. In the second scenario, the temperature was set at 500 °C for 60 min before the temperature was increased to 800 °C with a high heating rate. After the temperature reached 800 °C, the condition was maintained for approximately 45 min. Results showed that an increase in the liquid and gas yields was achieved when the temperature increased after optimum conditions. Increased yield was also obtained when the proportion of scrap tire was increased in the feedstock. Several other important findings are discussed in this paper, including the phases of pyrolysis oil, features of the liquid product, and characteristics of the byproducts. All products from both scenarios were analyzed by various methods to understand their fuel characteristics

Development of secondary chamber for tar cracking-improvement of wood pyrolysis performance in pre-vacuum chamber

Science.gov (United States)

Siahaan, S.; Homma, H.; Homma, H.

2018-02-01

Energy crisis and global warming, in other words, climate change are critical topics discussed in various parts of the world. Global warming primarily result from too much emission of carbon dioxide (CO2) in the atmosphere. To mitigate global warming, or climate change and improve electrification in rural areas, wood pyrolysis technology is developed in a laboratory scale, of which gases are directly applicable to the gas engine generator. Our laboratory has developed a prototype of wood pyrolysis plant with a pre-vacuum chamber. However, tar yield was around 40 wt% of feedstock. This research aims to reduce tar yield by secondary tar cracking. For the secondary tar cracking, a secondary pre-vacuum chamber is installed after primary pre-vacuum chamber. Gases generated in the primary pre-vacuum chamber are lead into the secondary chamber that is heated up to 1000 K. This paper reports performance of the secondary chamber for secondary tar cracking in homogeneous mode and heterogeneous mode with char.

Kinetics of pyrolysis and combustion of spherical wood particles in a fluidized bed

International Nuclear Information System (INIS)

Mazziotti di Celso, Giuseppe; Rapagnà, Sergio; Prisciandaro, Marina; Zanoelo, Everton Fernando

2014-01-01

Highlights: • H 2 , CO 2 , CO and CH 4 released during wood pyrolysis were experimentally monitored. • CO 2 formed by burning the residual tar/char mixture was experimentally determined. • The kinetics of species production was reproduced with two simplified models. • The increase of the bed reactor temperature statistically enhanced the gas yield. • The pyrolysis time is statistically reduced by decreasing the particle size. - Abstract: The kinetics of wood pyrolysis and combustion of residual fuel at different particle diameters and temperatures was investigated. A known mass of wooden spheres was fed at the top of a fluidized bed reactor filled with olivine particles and fluidized with nitrogen. The concentration of H 2 , CO 2 , CO and CH 4 was on-line monitored with gas analyzers. An irreversible first order reaction was applied to describe the biomass pyrolysis. The rate constant was dependent on the average temperature of wood particle, obtained by solving the transient one-dimensional problem of heat conduction in a sphere. The rate for an irreversible second order reaction between the residual fuel and oxygen at the fluid–solid interface, which takes a finite resistance to mass transfer into account, was adopted to describe the combustion. The semi-empirical kinetic models for pyrolysis and combustion were able to describe, with certain limitations inherent to model simplifications, the experimental transient results of molar flow rates of major released species. A statistical model based on the results of the factorial design of experiments (3 2 ) confirmed a statistical significant effect of temperature and wood particle diameter on the gas yield and time of pyrolysis, respectively

Investigating and modeling the pyrolysis kinetic of leaves and stems of pistachio trees for biofuel production

Directory of Open Access Journals (Sweden)

M Ostad Hoseini

2016-09-01

Full Text Available Introduction The lignocelluloses materials have high potential for producing various types of biofuels. These materials include various parts of plants, especially leaves and stems that are left without a specific usage after annual pruning. These residues can be used through slow or fast pyrolysis process for production of liquid and gaseous biofuels. The slow pyrolysis is taking place at temperatures below 500°C while fast pyrolysis process takes place at a temperature above 700°C. Various studies on production of biofuels from plant residues have shown that the temperature, heating rate and the resident time of pyrolysis process are the main factors that affect the final product quality. At present time, in Iran, there are more than 360 thousands hectares of pistachio growing fields which annually produce over 215 thousands metric tons residues which are mainly leaves and stems. The main objective of this study was to measure the heating properties of the powders prepared from the leaves and the stem of pistachio trees. These properties include higher heating value (HHV, lower heating value (LHV and thermal gravimetric analysis (TGA of the powders. Then the powders were separately pyrolysed and the kinetic of the pyrolysis process for producing charcoal from them was investigated. Materials and Methods In this research, leaves and stems of pistachio trees were initially analyzed to determine their chemical constituents including moisture content, volatile compounds, carbon (C, hydrogen (H, nitrogen (N, sulfur (S and oxygen (O content. Using these constituents the height heating value and low heating value for the leaves and the stems were determined. The thermal gravimetric analysis (TGA of the powders was made to select a proper heating temperature for pyrolysis of the powders. In each experiment about 10 g of powder powders were pyrolyzed to produce char. Based on TGA results, the pyrolysis experiments were performed at 350, 400, 450 and

Quality improvement of pyrolysis oil from waste rubber by adding sawdust

International Nuclear Information System (INIS)

Wang, Wen-liang; Chang, Jian-min; Cai, Li-ping; Shi, Sheldon Q.

2014-01-01

Highlights: • Rubber-pyrolysis oil is difficult to be fuel due to high proportion of PAHs. • The efficiency of pyrolysis was increased as the percentage of sawdust increased. • The adding of sawdust improved pyrolysis oil quality by reducing the PAHs content. • Adding sawdust reduced nitrogen/sulfur in oil and was easier to convert to diesel. - Abstract: This work was aimed at improving the pyrolysis oil quality of waste rubber by adding larch sawdust. Using a 1 kg/h stainless pyrolysis reactor, the contents of sawdust in rubber were gradually increased from 0%, 50%, 100% and 200% (wt%) during the pyrolysis process. Using a thermo-gravimetric (TG) analyzer coupled with Fourier transform infrared (FTIR) analysis of evolving products (TG–FTIR), the weight loss characteristics of the heat under different mixtures of sawdust/rubber were observed. Using the pyrolysis–gas chromatography (GC)–mass spectrometry (Py–GC/MS), the vapors from the pyrolysis processes were collected and the compositions of the vapors were examined. During the pyrolysis process, the recovery of the pyrolysis gas and its composition were measured in-situ at a reaction temperature of 450 °C and a retaining time of 1.2 s. The results indicated that the efficiency of pyrolysis was increased and the residual carbon was reduced as the percentage of sawdust increased. The adding of sawdust significantly improved the pyrolysis oil quality by reducing the polycyclic aromatic hydrocarbons (PAHs) and nitrogen and sulfur compounds contents, resulting in an improvement in the combustion efficiency of the pyrolysis oil

Quality improvement of pyrolysis oil from waste rubber by adding sawdust

Energy Technology Data Exchange (ETDEWEB)

Wang, Wen-liang [MOE Key Laboratory of Wooden Material Science and Application, College of Material Science and Technology, Wood Science and Technology, Beijing Forestry University, 100083 Beijing (China); Chang, Jian-min, E-mail: cjianmin@bjfu.edu.cn [MOE Key Laboratory of Wooden Material Science and Application, College of Material Science and Technology, Wood Science and Technology, Beijing Forestry University, 100083 Beijing (China); Cai, Li-ping [Mechanical and Energy Engineering Department, University of North Texas, 3940 N. Elm, Denton 72076, TX (United States); Shi, Sheldon Q., E-mail: Sheldon.Shi@unt.edu [Mechanical and Energy Engineering Department, University of North Texas, 3940 N. Elm, Denton 72076, TX (United States)

2014-12-15

Highlights: • Rubber-pyrolysis oil is difficult to be fuel due to high proportion of PAHs. • The efficiency of pyrolysis was increased as the percentage of sawdust increased. • The adding of sawdust improved pyrolysis oil quality by reducing the PAHs content. • Adding sawdust reduced nitrogen/sulfur in oil and was easier to convert to diesel. - Abstract: This work was aimed at improving the pyrolysis oil quality of waste rubber by adding larch sawdust. Using a 1 kg/h stainless pyrolysis reactor, the contents of sawdust in rubber were gradually increased from 0%, 50%, 100% and 200% (wt%) during the pyrolysis process. Using a thermo-gravimetric (TG) analyzer coupled with Fourier transform infrared (FTIR) analysis of evolving products (TG–FTIR), the weight loss characteristics of the heat under different mixtures of sawdust/rubber were observed. Using the pyrolysis–gas chromatography (GC)–mass spectrometry (Py–GC/MS), the vapors from the pyrolysis processes were collected and the compositions of the vapors were examined. During the pyrolysis process, the recovery of the pyrolysis gas and its composition were measured in-situ at a reaction temperature of 450 °C and a retaining time of 1.2 s. The results indicated that the efficiency of pyrolysis was increased and the residual carbon was reduced as the percentage of sawdust increased. The adding of sawdust significantly improved the pyrolysis oil quality by reducing the polycyclic aromatic hydrocarbons (PAHs) and nitrogen and sulfur compounds contents, resulting in an improvement in the combustion efficiency of the pyrolysis oil.

Fates of Chemical Elements in Biomass during Its Pyrolysis.

Science.gov (United States)

Liu, Wu-Jun; Li, Wen-Wei; Jiang, Hong; Yu, Han-Qing

2017-05-10

Biomass is increasingly perceived as a renewable resource rather than as an organic solid waste today, as it can be converted to various chemicals, biofuels, and solid biochar using modern processes. In the past few years, pyrolysis has attracted growing interest as a promising versatile platform to convert biomass into valuable resources. However, an efficient and selective conversion process is still difficult to be realized due to the complex nature of biomass, which usually makes the products complicated. Furthermore, various contaminants and inorganic elements (e.g., heavy metals, nitrogen, phosphorus, sulfur, and chlorine) embodied in biomass may be transferred into pyrolysis products or released into the environment, arousing environmental pollution concerns. Understanding their behaviors in biomass pyrolysis is essential to optimizing the pyrolysis process for efficient resource recovery and less environmental pollution. However, there is no comprehensive review so far about the fates of chemical elements in biomass during its pyrolysis. Here, we provide a critical review about the fates of main chemical elements (C, H, O, N, P, Cl, S, and metals) in biomass during its pyrolysis. We overview the research advances about the emission, transformation, and distribution of elements in biomass pyrolysis, discuss the present challenges for resource-oriented conversion and pollution abatement, highlight the importance and significance of understanding the fate of elements during pyrolysis, and outlook the future development directions for process control. The review provides useful information for developing sustainable biomass pyrolysis processes with an improved efficiency and selectivity as well as minimized environmental impacts, and encourages more research efforts from the scientific communities of chemistry, the environment, and energy.

Co-pyrolysis of rice straw and polypropylene using fixed-bed pyrolyzer

Science.gov (United States)

Izzatie, N. I.; Basha, M. H.; Uemura, Y.; Mazlan, M. A.; Hashim, M. S. M.; Amin, N. A. M.; Hamid, M. F.

2016-11-01

The present work encompasses the impact of temperature (450, 500, 550, 600 °C) on the properties of pyrolysis oil and on other product yield for the co-pyrolysis of Polypropylene (PP) plastics and rice straw. Co-pyrolysis of PP plastic and rice straw were conducted in a fixed-bed drop type pyrolyzer under an inert condition to attain maximum oil yield. Physically, the pyrolysis oil is dark-brown in colour with free flowing and has a strong acrid smell. Copyrolysis between these typically obtained in maximum pyrolysis oil yields up to 69% by ratio 1:1 at a maximum temperature of 550 °C. From the maximum yield of pyrolysis oil, characterization of pyrolysis product and effect of biomass type of the composition were evaluated. Pyrolysis oil contains a high water content of 66.137 wt.%. Furfural, 2- methylnaphthalene, tetrahydrofuran (THF), toluene and acetaldehyde were the major organic compounds found in pyrolysis oil of rice straw mixed with PP. Bio-char collected from co-pyrolysis of rice straw mixed with PP plastic has high calorific value of 21.190 kJ/g and also carbon content with 59.02 wt.% and could contribute to high heating value. The non-condensable gases consist of hydrogen, carbon monoxide, and methane as the major gas components.

Quality improvement of pyrolysis oil from waste rubber by adding sawdust.

Science.gov (United States)

Wang, Wen-liang; Chang, Jian-min; Cai, Li-ping; Shi, Sheldon Q

2014-12-01

This work was aimed at improving the pyrolysis oil quality of waste rubber by adding larch sawdust. Using a 1 kg/h stainless pyrolysis reactor, the contents of sawdust in rubber were gradually increased from 0%, 50%, 100% and 200% (wt%) during the pyrolysis process. Using a thermo-gravimetric (TG) analyzer coupled with Fourier transform infrared (FTIR) analysis of evolving products (TG-FTIR), the weight loss characteristics of the heat under different mixtures of sawdust/rubber were observed. Using the pyrolysis-gas chromatography (GC)-mass spectrometry (Py-GC/MS), the vapors from the pyrolysis processes were collected and the compositions of the vapors were examined. During the pyrolysis process, the recovery of the pyrolysis gas and its composition were measured in-situ at a reaction temperature of 450 °C and a retaining time of 1.2s. The results indicated that the efficiency of pyrolysis was increased and the residual carbon was reduced as the percentage of sawdust increased. The adding of sawdust significantly improved the pyrolysis oil quality by reducing the polycyclic aromatic hydrocarbons (PAHs) and nitrogen and sulfur compounds contents, resulting in an improvement in the combustion efficiency of the pyrolysis oil. Copyright © 2014 Elsevier Ltd. All rights reserved.

Reaction mechanisms in cellulose pyrolysis: a literature review

Energy Technology Data Exchange (ETDEWEB)

Molton, P.M.; Demmitt, T.F.

1977-08-01

A bibliographic review of 195 references is presented outlining the history of the research into the mechanisms of cellulose pyrolysis. Topics discussed are: initial product identification, mechanism of initial formation of levoglucosan, from cellulose and from related compounds, decomposition of cellulose to other compounds, formation of aromatics, pyrolysis of levoglucosan, crosslinking of cellulose, pyrolytic reactions of cellulose derivatives, and the effects of inorganic salts on the pyrolysis mechanism. (JSR)

An experimental and kinetic modeling study of glycerol pyrolysis

International Nuclear Information System (INIS)

Fantozzi, F.; Frassoldati, A.; Bartocci, P.; Cinti, G.; Quagliarini, F.; Bidini, G.; Ranzi, E.M.

2016-01-01

Highlights: • Glycerol pyrolysis can produce about 44–48%v hydrogen at 750–800 °C. • A simplified 452 reactions kinetic model of glycerol pyrolysis has been developed. • The model has good agreement with experimental data. • Non condensable gas yields can reach 70%. - Abstract: Pyrolysis of glycerol, a by-product of the biodiesel industry, is an important potential source of hydrogen. The obtained high calorific value gas can be used either as a fuel for combined heat and power (CHP) generation or as a transportation fuel (for example hydrogen to be used in fuel cells). Optimal process conditions can improve glycerol pyrolysis by increasing gas yield and hydrogen concentration. A detailed kinetic mechanism of glycerol pyrolysis, which involves 137 species and more than 4500 reactions, was drastically simplified and reduced to a new skeletal kinetic scheme of 44 species, involved in 452 reactions. An experimental campaign with a batch pyrolysis reactor was properly designed to further validate the original and the skeletal mechanisms. The comparisons between model predictions and experimental data strongly suggest the presence of a catalytic process promoting steam reforming of methane. High pyrolysis temperatures (750–800 °C) improve process performances and non-condensable gas yields of 70%w can be achieved. Hydrogen mole fraction in pyrolysis gas is about 44–48%v. The skeletal mechanism developed can be easily used in Computational Fluid Dynamic software, reducing the simulation time.

THE EFFECT OF AMOUNT OF NATURAL ZEOLIT CATALYST IN PRODUCT OF POLYPROPILENE (PP PLASTIC WASTE PYROLYSIS

Directory of Open Access Journals (Sweden)

khalimatus sa'diyah

2015-12-01

Full Text Available To overcome the waste problem, especially plastic waste , environmental concerned scientists from various disciplines have conducted various research and actions. Catalytic pyrolysis processes was chosen as an alternative method to recycle plastic waste. The purpose of this experiment was to determine the effect of natural zeolit catalyst on the pyrolysis process with oxygen-free conditions to obtain maximum hydrocarbon compounds (gasoline fraction in C5-C9. The process of pyrolysis was conducted in 3.5 dm3 unstirred stainless steel semi-batch reactor. This process operated at atmospheric pressure with nitrogen injection. Plastic waste that used in this particular paper was 50 grams of polypropylene (PP. In pyrolysis process, natural zeolite catalysts was added 2,5 gram (5% weight of natural zeolite per weight of plastic waste samples, 5 gram (10% , and 10 gram (20%. Temperature of pyrolysis was 450°C and were maintained until 30 minutes. Steam that produced from pyrolisis was condensed and analysed by gas chromatography–mass spectrometry (GC-MS to determine yield of hydrocarbons produced. From the analysis of GC-MS, liquid products of pyrolysis contained lots of aromatic hydrocarbons. The optimal amount of catalyst that produce liquid with hydrocarbon compound that has the quality of gasoline was 10 gram (20% with ≤C9 composition as 29,16% n-paraffin, 9,22% cycloparaffin, and 61,64% aromatics.

Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants.

Science.gov (United States)

Adrados, A; De Marco, I; Lopez-Urionabarrenechea, A; Caballero, B M; Laresgoiti, M F

2013-01-01

In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm(3) reactor, swept with 1 L min(-1) N(2), at 500°C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33-40 MJ kg(-1)). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO(2); their HHV is in the range of 18-46 MJ kg(-1). The amount of COCO(2) increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char. Copyright © 2012 Elsevier Ltd. All rights reserved.

From biomass to advanced bio-fuel by catalytic pyrolysis/hydro-processing: hydrodeoxygenation of bio-oil derived from biomass catalytic pyrolysis.

Science.gov (United States)

Wang, Yuxin; He, Tao; Liu, Kaituo; Wu, Jinhu; Fang, Yunming

2012-03-01

Compared hydrodeoxygenation experimental studies of both model compounds and real bio-oil derived from biomass fast pyrolysis and catalytic pyrolysis was carried out over two different supported Pt catalysts. For the model compounds, the deoxygenation degree of dibenzofuran was higher than that of cresol and guaiacol over both Pt/Al(2)O(3) and the newly developed Pt supported on mesoporous zeolite (Pt/MZ-5) catalyst, and the deoxygenation degree of cresol over Pt/MZ-5 was higher than that over Pt/Al(2)O(3). The results indicated that hydrodeoxygenation become much easier upon oxygen reduction. Similar to model compounds study, the hydrodeoxygenation of the real bio-oil derived from catalytic pyrolysis was much easier than that from fast pyrolysis over both Pt catalysts, and the Pt/MZ-5 again shows much higher deoxygenation ability than Pt/Al(2)O(3). Clearly synergy between catalytic pyrolysis and bio-oil hydro-processing was found in this paper and this finding will lead an advanced biofuel production pathway in the future. Copyright © 2012 Elsevier Ltd. All rights reserved.

Carbon Isotope Characterization of Organic Intermediaries in Hydrothermal Hydrocarbon Synthesis by Pyrolysis-GC-MS-C-IRMS

Science.gov (United States)

Socki, Richard A.; Fu, Qi; Niles, Paul B.

2010-01-01

We report results of experiments designed to characterize the carbon isotope composition of intermediate organic compounds produced as a result of mineral surface catalyzed reactions. The impetus for this work stems from recently reported detection of methane in the Martian atmosphere coupled with evidence showing extensive water-rock interaction during Martian history. Abiotic formation by Fischer-Tropsch-type (FTT) synthesis during serpentinization reactions may be one possible process responsible for methane generation on Mars, and measurement of carbon and hydrogen isotopes of intermediary organic compounds can help constrain the origin of this methane. Of particular interest within the context of this work is the isotopic composition of organic intermediaries produced on the surfaces of mineral catalysts (i.e. magnetite) during hydrothermal experiments, and the ability to make meaningful and reproducible isotope measurements. Our isotope measurements utilize a unique analytical technique combining Pyrolysis-Gas Chromatograph-Mass Spectrometry-Combustion-Isotope Ratio Mass Specrometry (Py-GC-MS-C-IRMS). Others have conducted similar pyrolysis-IRMS experiments on low molecular weight organic acids (Dias, et al, Organic Geochemistry, 33 [2002]). Our technique differs in that it carries a split of the pyrolyzed GC-separated product to a Thermo DSQ-II quadrupole mass spectrometer as a means of making qualitative and semi-quantitative compositional measurements of the organic compounds. A sample of carboxylic acid (mixture of C1 through C6) was pyrolyzed at 100 XC and passed through the GC-MS-C-IRMS (combusted at 940 XC). In order to test the reliability of our technique we compared the _13C composition of different molecular weight organic acids (from C1 through C6) extracted individually by the traditional sealed-tube cupric oxide combustion (940 XC) method with the _13C produced by our pyrolysis technique. Our data indicate that an average 4.3. +/-0.5. (V

Pyrolysis of waste tyres: a review.

Science.gov (United States)

Williams, Paul T

2013-08-01

Approximately 1.5 billion tyres are produced each year which will eventually enter the waste stream representing a major potential waste and environmental problem. However, there is growing interest in pyrolysis as a technology to treat tyres to produce valuable oil, char and gas products. The most common reactors used are fixed-bed (batch), screw kiln, rotary kiln, vacuum and fluidised-bed. The key influence on the product yield, and gas and oil composition, is the type of reactor used which in turn determines the temperature and heating rate. Tyre pyrolysis oil is chemically very complex containing aliphatic, aromatic, hetero-atom and polar fractions. The fuel characteristics of the tyre oil shows that it is similar to a gas oil or light fuel oil and has been successfully combusted in test furnaces and engines. The main gases produced from the pyrolysis of waste tyres are H(2), C(1)-C(4) hydrocarbons, CO(2), CO and H(2)S. Upgrading tyre pyrolysis products to high value products has concentrated on char upgrading to higher quality carbon black and to activated carbon. The use of catalysts to upgrade the oil to a aromatic-rich chemical feedstock or the production of hydrogen from waste tyres has also been reported. Examples of commercial and semi-commercial scale tyre pyrolysis systems show that small scale batch reactors and continuous rotary kiln reactors have been developed to commercial scale. Copyright © 2013 Elsevier Ltd. All rights reserved.

Pyrolysis temperature influences ameliorating effects of biochars on acidic soil.

Science.gov (United States)

Wan, Qing; Yuan, Jin-Hua; Xu, Ren-Kou; Li, Xing-Hui

2014-02-01

The biochars were prepared from straws of canola, corn, soybean, and peanut at different temperatures of 300, 500, and 700 °C by means of oxygen-limited pyrolysis.Amelioration effects of these biochars on an acidic Ultisol were investigated with incubation experiments, and application rate of biochars was 10 g/kg. The incorporation of these biochars induced the increase in soil pH, soil exchangeable base cations, base saturation, and cation exchange capacity and the decrease in soil exchangeable acidity and exchangeable Al. The ameliorating effects of biochars on acidic soil increased with increase in their pyrolysis temperature. The contribution of oxygen-containing functional groups on the biochars to their ameliorating effects on the acidic soil decreased with the rise in pyrolysis temperature, while the contribution from carbonates in the biochars changed oppositely. The incorporation of the biochars led to the decrease in soil reactive Al extracted by 0.5mol/L CuCl2, and the content of reactive Al was decreased with the increase in pyrolysis temperature of incorporated biochars. The biochars generated at 300 °C increased soil organically complexed Al due to ample quantity of oxygen-containing functional groups such as carboxylic and phenolic groups on the biochars, while the biochars generated at 500 and 700 °C accelerated the transformation of soil exchangeable Al to hydroxyl-Al polymers due to hydrolysis of Al at higher pH. Therefore, the crop straw-derived biochars can be used as amendments for acidic soils and the biochars generated at relatively high temperature have great ameliorating effects on the soils.

Research on pyrolysis behavior of Camellia sinensis branches via the Discrete Distributed Activation Energy Model.

Science.gov (United States)

Zhou, Bingliang; Zhou, Jianbin; Zhang, Qisheng

2017-10-01

This study aims at investigating the pyrolysis behavior of Camellia sinensis branches by the Discrete Distributed Activation Energy Model (DAEM) and thermogravimetric experiments. Then the Discrete DAEM method is used to describe pyrolysis process of Camellia sinensis branches dominated by 12 characterized reactions. The decomposition mechanism of Camellia sinensis branches and interaction with components are observed. And the reaction at 350.77°C is a significant boundary of the first and second reaction range. The pyrolysis process of Camellia sinensis branches at the heating rate of 10,000°C/min is predicted and provides valuable references for gasification or combustion. The relationship and function between four typical indexes and heating rates from 10 to 10,000°C/min are revealed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Change of physical and chemical properties of the solid phase during biomass pyrolysis; Aenderung der physikalisch-chemischen Eigenschaften des Feststoffs waehrend der Biomassepyrolyse

Energy Technology Data Exchange (ETDEWEB)

Klose, Wolfgang [Kassel Univ. (Germany). Inst. fuer Thermische Energietechnik; Rincon, Sonia; Gomez, Alexander [Universidad Nacional de Colombia, Bogota (Colombia). Dept. de Ingenieria Mecanica y Mecatronica

2009-01-15

The effects of the final pyrolysis temperature on the development of the chemical composition and on the porosity of biomass undergoing pyrolysis are investigated through experiments in a thermobalance at laboratory scale of grams. Changes in the grain size of individual particles of biomass during pyrolysis are also investigated as a function of temperature in a microscope equipped with heating and camera. Oil palm shells are selected as raw materials due to their availability as biomass residue and their physical and chemical characteristics. These experiments are important for reactor design purposes in the field of thermochemical conversion, offering important information for the mathematical modelling of the processes. (orig.)

Pyrolysis-GCMS Analysis of Solid Organic Products from Catalytic Fischer-Tropsch Synthesis Experiments

Science.gov (United States)

Locke, Darren R.; Yazzie, Cyriah A.; Burton, Aaron S.; Niles, Paul B.; Johnson, Natasha M.

2015-01-01

Abiotic synthesis of complex organic compounds in the early solar nebula that formed our solar system is hypothesized to occur via a Fischer-Tropsch type (FTT) synthesis involving the reaction of hydrogen and carbon monoxide gases over metal and metal oxide catalysts. In general, at low temperatures (less than 200 C), FTT synthesis is expected to form abundant alkane compounds while at higher temperatures (greater than 200 C) it is expected to product lesser amounts of n-alkanes and greater amounts of alkene, alcohol, and polycyclic aromatic hydrocarbons (PAHs). Experiments utilizing a closed-gas circulation system to study the effects of FTT reaction temperature, catalysts, and number of experimental cycles on the resulting solid insoluble organic products are being performed in the laboratory at NASA Goddard Space Flight Center. These experiments aim to determine whether or not FTT reactions on grain surfaces in the protosolar nebula could be the source of the insoluble organic matter observed in meteorites. The resulting solid organic products are being analyzed at NASA Johnson Space Center by pyrolysis gas chromatography mass spectrometry (PY-GCMS). PY-GCMS yields the types and distribution of organic compounds released from the insoluble organic matter generated from the FTT reactions. Previously, exploratory work utilizing PY-GCMS to characterize the deposited organic materials from these reactions has been reported. Presented here are new organic analyses using magnetite catalyst to produce solid insoluble organic FTT products with varying reaction temperatures and number of experimental cycles.

Formation of nitrogen-containing compounds during microwave pyrolysis of microalgae: Product distribution and reaction pathways.

Science.gov (United States)

Huang, Feng; Tahmasebi, Arash; Maliutina, Kristina; Yu, Jianglong

2017-12-01

The formation of nitrogen-containing compounds in bio-oil during microwave pyrolysis of Chlorella and Spirulina microalgae has been investigated in this study. Activated carbon (AC) and magnetite (Fe 3 O 4 ) were used as microwave receptors during microwave pyrolysis experiments. It has been found that the use of Fe 3 O 4 increased the total yield of bio-oil. The use of different microwave receptors did not seem to have affected the total yield of nitrogen-containing compounds in the bio-oil. However, Fe 3 O 4 promoted the formation of nitrogen-containing aliphatics, thereby reducing the formation of nitrogen-containing aromatics. The use of AC promoted the dehydration reactions during amino acid decomposition, thereby enhancing the formation of nitrogen-containing aromatics during pyrolysis. From the gas chromatography-mass spectrometry (GC-MS) analysis results, the major high-value nitrogen-containing compounds in the pyrolysis bio-oil of Chlorella and Spirulina were identified as indole and dodecamide. The formation mechanisms of nitrogen-containing compounds were proposed and discussed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Catalytic pyrolysis of woody biomass in a fluidized bed reactor: influence of the zeolite structure

Energy Technology Data Exchange (ETDEWEB)

A. Aho; N. Kumar; K. Eranen; T. Salmi; M. Hupa; D.Yu. Murzin [Aabo Akademi University, Aabo/Turku (Finland). Process Chemistry Centre, Laboratory of Industrial Chemistry and Reaction Engineering

2008-09-15

Catalytic pyrolysis of biomass from pine wood was carried out in a fluidized bed reactor at 450{sup o}C. Different structures of acidic zeolite catalysts were used as bed material in the reactor. Proton forms of Beta, Y, ZSM-5, and Mordenite were tested as catalysts in the pyrolysis of pine, while quartz sand was used as a reference material in the non-catalytic pyrolysis experiments. The yield of the pyrolysis product phases was only slightly influenced by the structures, at the same time the chemical composition of the bio-oil was dependent on the structure of acidic zeolite catalysts. Ketones and phenols were the dominating groups of compounds in the bio-oil. The formation of ketones was higher over ZSM-5 and the amount of acids and alcohols lower than over the other bed materials tested. Mordenite and quartz sand produced smaller quantities of polyaromatic hydrocarbons than the other materials tested. It was possible to successfully regenerate the spent zeolites without changing the structure of the zeolite. 12 refs., 9 figs., 5 tabs.

Hot char-catalytic reforming of volatiles from MSW pyrolysis

International Nuclear Information System (INIS)

Wang, Na; Chen, Dezhen; Arena, Umberto; He, Pinjing

2017-01-01

Highlights: • Volatile from MSW pyrolysis is reformed with hot char from the same pyrolysis process. • The yields of syngas increase evidently with H 2 being the main contributor and the major component of the syngas. • Pyrolysis oil becomes light and its composition distribution is narrowed. • The HHV, volatile elements and alkali metals contents in the char decrease. • The emissions including SO 2 , NO, NO 2 and HCN changed after reforming process. - Abstract: Volatile products obtained from pyrolysis of municipal solid waste (MSW), including syngas and pyrolysis oil, were forced to contact the hot char from the same pyrolysis process at 500–600 °C in a fixed bed reactor to be reformed. The yields and properties of syngas, char and pyrolysis liquid were investigated; and the energy re-distribution among the products due to char reforming was quantified. The preliminary investigation at lab scale showed that hot char-catalytic reforming of the volatiles leads to an increase in the dry syngas yield from 0.25 to 0.37 N m 3 kg −1 MSW at 550 °C. Accordingly, the carbon conversion ratio into syngas increases from 29.6% to 35.0%; and the MSW chemical energy transferred into syngas increased from 41.8% to 47.4%. The yield of pyrolysis liquid products, including pyrolysis oil and water, decreased from 27.3 to 16.5 wt%, and the molecular weight of the oil becoming lighter. Approximately 60% of the water vapour contained in the volatiles converted into syngas. After reforming, the concentrations of SO 2 and HCN in the syngas decreases, while those of NO and NO 2 increase. The char concentrations of N, H, C and alkali metal species decreased and its higher heating value decreased too.

Rotor for a pyrolysis centrifuge reactor

DEFF Research Database (Denmark)

2015-01-01

The present invention relates to a rotor for a pyrolysis centrifuge reactor, said rotor comprising a rotor body having a longitudinal centre axis, and at least one pivotally mounted blade being adapted to pivot around a pivot axis under rotation of the rotor body around the longitudinal centre axis....... Moreover, the present invention relates to a pyrolysis centrifuge reactor applying such a rotor....

Pyrolysis of Municipal Green Waste: A Modelling, Simulation and Experimental Analysis

Directory of Open Access Journals (Sweden)

Mohammed J. Kabir

2015-07-01

Full Text Available Pyrolysis is the thermo-chemical conversion of carbonaceous feedstock in the absence of oxygen to produce bio-fuel (bio-oil, bio-char and syn-gas. Bio-fuel production from municipal green waste (MGW through the pyrolysis process has attracted considerable attention recently in the renewable energy sector because it can reduce greenhouse gas emissions and contribute to energy security. This study analyses properties of MGW feedstock available in Rockhampton city of Central Queensland, Australia, and presents an experimental investigation of producing bio-fuel from that MGW through the pyrolysis process using a short sealed rotary furnace. It was found from the experiment that about 19.97% bio-oil, 40.83% bio-char and 29.77% syn-gas can be produced from the MGW. Then, a four-stage steady state simulation model is developed for pyrolysis process performance simulation using Aspen Plus software. In the first stage, the moisture content of the MGW feed is reduced. In the second stage, the MGW is decomposed according to its elemental constituents. In the third stage, condensate material is separated and, finally, the pyrolysis reactions are modelled using the Gibbs free energy minimisation approach. The MGW’s ultimate and proximate analysis data were used in the Aspen Plus simulation as input parameters. The model is validated with experimentally measured data. A good agreement between simulation and experimental results was found. More specifically, the variation of modelling and experimental elemental compositions of the MGW was found to be 7.3% for carbon, 15.82% for hydrogen, 7.04% for nitrogen and 5.56% for sulphur. The validated model is used to optimise the biofuel production from the MGW as a function of operating variables such as temperature, moisture content, particle size and process heat air–fuel ratio. The modelling and optimisation results are presented, analysed and discussed.

Historical Developments of Pyrolysis Reactors : A Review

NARCIS (Netherlands)

Garcia-Nunez, J. A.; Pelaez-Samaniego, M.R.; Garcia-Perez, M. E.; Fonts, I.; Abrego, J.; Westerhof, R. J.M.; Garcia Perez, M.

2017-01-01

This paper provides a review of pyrolysis technologies, focusing on reactor designs and companies commercializing these technologies. The renewed interest in pyrolysis is driven by the potential to convert lignocellulosic materials into bio-oil and biochar and the use of these intermediates for the

Experimental study of Coal Pyrolysis 2.: Experimental characterisation of volatile matter

International Nuclear Information System (INIS)

Hugony, F.; Migliavacca, G.

2008-01-01

In this paper considerations about experiments conducted through T G-Ftir are reported, in order to study the gas composition coming from coal pyrolysis. In particular qualitative and semi-qualitative evaluation of hydrocarbon evolution rate, as CH4, C2H4 and C3H6 are reported. It has been observed a strict relation between the evolution rate of the listed compounds, the coal rank and their elementary composition. The reported data constitute a good support to the validation of the predictive models of coal devolatilization. To complete the study two papers will be published in the next months: one containing experimental data from pyrolysis process in a fixed bed reactor and another one concerning the NMR analysis of the produced char. [it

Novel technique for coal pyrolysis and hydrogenation product analysis

Energy Technology Data Exchange (ETDEWEB)

Pfefferle, L.D.; Boyle, J.

1993-03-15

A microjet reactor coupled to a VUV photoionization time-of-flight mass spectrometer has been used to obtain species measurements during high temperature pyrolysis and oxidation of a wide range of hydrocarbon compounds ranging from allene and acetylene to cyclohexane, benzene and toluene. Initial work focused on calibration of the technique, optimization of ion collection and detection and characterization of limitations. Using the optimized technique with 118 nm photoionization, intermediate species profiles were obtained for analysis of the hydrocarbon pyrolysis and oxidation mechanisms. The soft'' ionization, yielding predominantly molecular ions, allowed the study of reaction pathways in these high temperature systems where both sampling and detection challenges are severe. Work has focused on the pyrolysis and oxidative pyrolysis of aliphatic and aromatic hydrocarbon mixtures representative of coal pyrolysis and hydropyrolysis products. The detailed mass spectra obtained during pyrolysis and oxidation of hydrocarbon mixtures is especially important because of the complex nature of the product mixture even at short residence times and low primary reactant conversions. The combustion community has advanced detailed modeling of pyrolysis and oxidation to the C4 hydrocarbon level but in general above that size uncertainties in rate constant and thermodynamic data do not allow us to a priori predict products from mixed hydrocarbon pyrolyses using a detailed chemistry model. For pyrolysis of mixtures of coal-derived liquid fractions with a large range of compound structures and molecular weights in the hundreds of amu the modeling challenge is severe. Lumped models are possible from stable product data.

Cell heterogeneity problems in the analysis of zero power experiments

International Nuclear Information System (INIS)

Grimstone, M.J.; Stevenson, J.M.

1979-01-01

Methods are described for treating plate and pin cell heterogeneity in the preparation of broad group cross-sections used in the analysis of zero power fast reactor experiments. Methods used at Karlsruhe and Winfrith are summarised and compared, with particular reference to the treatment of resonance shielding, the calculation of broad group spatial fine structure, the treatment of leakage and the calculation of anisotropic diffusion coefficients. The problems of cells near boundaries such as core-breeder interfaces and of singularities such as control rods are also considered briefly. Numerical studies carried out to investigate approximations in the methods are described. These include tests of the accuracy of one-dimensional cell modelling techniques, and the validation by Monte Carlo of methods for treating streaming in the calculation of diffusion coefficients. Comparisons are shown between the heterogeneity effects calculated by the Karlsruhe and Winfrith methods for typical pin and plate cells used in the BIZET experimental programme, and their effect in a whole reactor calculation is indicated. Comparisons are given with measurements which provide tests of the heterogeneity calculations. These include reaction rate scans within pin and plate cells, and reaction rate measurements across sectors of pin and plate fuel, where the flux tilt is determined by the relative reactivity of the pin and plate cells. Finally, the heterogeneity problems arising in the interpretation of reaction rate measurements are discussed. (author)

Photocatalytic Desulfurization of Waste Tire Pyrolysis Oil

Directory of Open Access Journals (Sweden)

Napida Hinchiranan

2011-11-01

Full Text Available Waste tire pyrolysis oil has high potential to replace conventional fossil liquid fuels due to its high calorific heating value. However, the large amounts of sulfurous compounds in this oil hinders its application. Thus, the aim of this research was to investigate the possibility to apply the photo-assisted oxidation catalyzed by titanium dioxide (TiO2, Degussa P-25 to partially remove sulfurous compounds in the waste tire pyrolysis oil under milder reaction conditions without hydrogen consumption. A waste tire pyrolysis oil with 0.84% (w/w of sulfurous content containing suspended TiO2 was irradiated by using a high-pressure mercury lamp for 7 h. The oxidized sulfur compounds were then migrated into the solvent-extraction phase. A maximum % sulfur removal of 43.6% was achieved when 7 g/L of TiO2 was loaded into a 1/4 (v/v mixture of pyrolysis waste tire oil/acetonitrile at 50 °C in the presence of air. Chromatographic analysis confirmed that the photo-oxidized sulfurous compounds presented in the waste tire pyrolysis oil had higher polarity, which were readily dissolved and separated in distilled water. The properties of the photoxidized product were also reported and compared to those of crude oil.

Reactions of oxygen containing structures in coal pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Hodek, W.; Kirschstein, J.; Van Heek, K.-H. (DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany, F.R.))

1991-03-01

In coal pyrolysis O-containing structures such as ether bridges and phenolic groups play an important role. Their reactions were studied by non-isothermal pyrolysis of a high volatile bituminous coal and some model polymers with gas chromatographic detection of the gaseous pyrolysis products. The coal was separated into the maceral groups vitrinite, exinite and inertinite, which showed markedly different pyrolysis behaviour. The formation of CO, methane and benzene was measured versus temperature. By comparison with polyphenyleneoxide and phenol-formaldehyde resins, it was found that the main volatilization, during which most of the tar is evolved, is initiated by cleavage of alkyl-aryl-ethers. Rearrangements of the primarily formed radicals lead to the formation of CO and methane at higher temperatures. 5 refs., 8 figs., 1 tab.

Studies on Pyrolysis Kinetic of Newspaper Wastes in a Packed Bed Reactor: Experiments, Modeling, and Product Characterization

Directory of Open Access Journals (Sweden)

Aparna Sarkar

2015-01-01

Full Text Available Newspaper waste was pyrolysed in a 50 mm diameter and 640 mm long reactor placed in a packed bed pyrolyser from 573 K to 1173 K in nitrogen atmosphere to obtain char and pyro-oil. The newspaper sample was also pyrolysed in a thermogravimetric analyser (TGA under the same experimental conditions. The pyrolysis rate of newspaper was observed to decelerate above 673 K. A deactivation model has been attempted to explain this behaviour. The parameters of kinetic model of the reactions have been determined in the temperature range under study. The kinetic rate constants of volatile and char have been determined in the temperature range under study. The activation energies 25.69 KJ/mol, 27.73 KJ/mol, 20.73 KJ/mol and preexponential factors 7.69 min−1, 8.09 min−1, 0.853 min−1 of all products (solid reactant, volatile, and char have been determined, respectively. A deactivation model for pyrolysis of newspaper has been developed under the present study. The char and pyro-oil obtained at different pyrolysis temperatures have been characterized. The FT-IR analyses of pyro-oil have been done. The higher heating values of both pyro-products have been determined.

Application of pyrolysis models in COCOSYS

International Nuclear Information System (INIS)

Klein-Hessling, W.; Roewekamp, M.; Allelein, H.J.

2001-01-01

For the assessment of the efficiency of severe accident management measures the simulation of severe accident development, progression and potential consequences in containments of nuclear power plants is required under conditions as realistic as possible. Therefore, the containment code item (COCOSYS) has been developed by GRS. The main objective is to provide a code system on the basis of mechanistic models for the comprehensive simulation of all relevant processes and plant states during severe accidents in the containment of light water reactors also covering the design basis accidents. In this context the simulation of oil and cable fires is of high priority. These processes strongly depend on the thermal hydraulic boundary conditions. An input-definition of the pyrolysis rate by the user is not consistent with the philosophy of COCOSYS. Therefore, a first attempt has been made for the code internal simulation of the pyrolysis rate and the following combustion process for oil and cable fires. The oil fire model used has been tested against the HDR E41.7 experiment. Because the cable fire model is still under development, a so-called 'simplified cable burning' model has been implemented in COCOSYS and tested against the HDR E42 cable fire experiments. Furthermore, in the frame of the bilateral (between German and Ukrainian government) project INT9131 in the field of fire safety at nuclear power plants (NPP), an exemplary fire hazard analysis (FHA) has been carried out for the cable spreading rooms below the unit control room of a VVER-1000/W-320 type reference plant. (authors)

Controlled air pyrolysis incinerator

International Nuclear Information System (INIS)

Dufrane, K.H.; Wilke, M.

1982-01-01

An advanced controlled air pyrolysis incinerator has been researched, developed and placed into commercial operation for both radioactive and other combustible wastes. Engineering efforts cocentrated on providing an incinerator which emitted a clean, easily treatable off-gas and which produced a minimum amount of secondary waste. Feed material is continuously fed by gravity into the system's pyrolysis chamber without sorting, shredding, or other such pretreatment. Metal objects, liquids such as oil and gasoline, or solid products such as resins, blocks of plastic, tire, animal carcasses, or compacted trash may be included along with normal processed waste. The temperature of the waste is very gradually increased in a reduced oxygen atmosphere. Volatile pyrolysis gases are produced, tar-like substances are cracked and the resulting product, a relatively uniform, easily burnable material, is introduced into the combustion chamber. Steady burning is thus accomplished under easily controlled excess air conditions with the off-gasthen passing through a simple dry clean-up system. Gas temperatures are then reduced by air dilution before passing through final HEPA filters. Both commercial and nuclear installations have been operated with the most recent application being the central incinerator to service West Germany's nuclear reactors

Influence of fast pyrolysis temperature on biochar labile fraction and short-term carbon loss in a loamy soil

International Nuclear Information System (INIS)

Bruun, Esben W.; Hauggaard-Nielsen, Henrik; Ibrahim, Norazana; Egsgaard, Helge; Ambus, Per; Jensen, Peter A.; Dam-Johansen, Kim

2011-01-01

Production of bio-oil, gas and biochar from pyrolysis of biomass is considered a promising technology for combined production of bioenergy and recalcitrant carbon (C) suitable for sequestration in soil. Using a fast pyrolysis centrifuge reactor (PCR) the present study investigated the relation between fast pyrolysis of wheat straw at different reactor temperatures and the short-term degradability of biochar in soil. After 115 days incubation 3-12% of the added biochar-C had been emitted as CO 2 . On average, 90% of the total biochar-C loss occurred within the first 20 days of the experiment, emphasizing the importance of knowing the biochar labile fraction when evaluating a specific biochars C sequestration potential. The pyrolysis temperature influenced the outputs of biochar, bio-oil and syngas significantly, as well as the stability of the biochar produced. Contrary to slow pyrolysis a fast pyrolysis process may result in incomplete conversion of biomass due to limitations to heat transfer and kinetics. In our case chemical analysis of the biochars revealed unconverted cellulosic and hemicellulosic fractions, which in turn were found to be proportional with the short-term biochar degradation in soil. As these labile carbohydrates are rapidly mineralized, their presence lowers the biochar-C sequestration potential. By raising the pyrolysis temperature, biochar with none or low contents of these fractions can be produced, but this will be on the expense of the biochar quantity. The yield of CO 2 neutral bio-oil is the other factor to optimize when adjusting the pyrolysis temperature settings to give the overall greatest climate change mitigation effect.

Vacuum pyrolysis of swine manure : biochar production and characteristics

Energy Technology Data Exchange (ETDEWEB)

Verma, M. [Inst. de recherche et de developpement en agroenvironnement Inc., Quebec City, PQ (Canada); Centre de recherche industrielle du Quebec, Quebec City, PQ (Canada); Godbout, S.; Larouche, J.P.; Lemay, S.P.; Pelletier, F. [Inst. de recherche et de developpement en agroenvironnement Inc., Quebec City, PQ (Canada); Solomatnikova, O. [Centre de recherche industrielle du Quebec, Quebec City, PQ (Canada); Brar, S.K. [Inst. national de la recherche scientifique, eau, terre et environnement, Quebec City, PQ (Canada)

2010-07-01

Quebec accounts for nearly 25 per cent of swine production in Canada. The issue of swine manure is addressed through land spreading and conversion into fertilizer. However, current regulations restrict the use of swine manure as fertilizer on most farmlands due to the problem of surplus phosphorus and nitrogen. Although many technologies exist to separate phosphorus and nitrogen from the organic-rich dry matter in swine manure, about 40 per cent of the treated waste matter must still be disposed in an environmentally sound manner. This study investigated the technical feasibility of pretreating the swine manure solids into biofuels on a farm-scale basis using vacuum pyrolysis process. A custom built stainless steel pressure vessel was used to carry out pyrolysis reaction of swine manure biomass at a temperature range between 200 to 600 degrees C under vacuum. The pyrolytic vapour was condensed in 2 glass condensers in series. The biochar was collected directly from the pyrolysis vessel following completion of the pyrolysis batch. The non condensable vapour and gases were considered as losses. Biochar, bio-oil, an aqueous phase and a gas mixture were the 4 products of the pyrolysis process. A thermogravimetric analysis of the swine manure samples was conducted before the pyrolysis tests. The study showed that 238 degrees C is the optimal pyrolysis temperature for biochar production.

Demonstration of the waste tire pyrolysis process on pilot scale in a continuous auger reactor

International Nuclear Information System (INIS)

Martínez, Juan Daniel; Murillo, Ramón; García, Tomás; Veses, Alberto

2013-01-01

Highlights: • The continuous pyrolysis of waste tire has been demonstrated at pilot scale in an auger reactor. • More than 500 kg of waste tires were processed in 100 operational hours. • The yields and characteristics of the pyrolysis products remained constant. • Mass and energy balances for an industrial scale plant are provided. • The reaction enthalpy necessary to perform the waste tire pyrolysis was determined. -- Abstract: This work shows the technical feasibility for valorizing waste tires by pyrolysis using a pilot scale facility with a nominal capacity of 150 kW th . A continuous auger reactor was operated to perform thirteen independent experiments that conducted to the processing of more than 500 kg of shredded waste tires in 100 h of operation. The reaction temperature was 550 °C and the pressure was 1 bar in all the runs. Under these conditions, yields to solid, liquid and gas were 40.5 ± 0.3, 42.6 ± 0.1 and 16.9 ± 0.3 wt.% respectively. Ultimate and proximate analyses as well as heating value analysis were conducted for both the solid and liquid fraction. pH, water content, total acid number (TAN), viscosity and density were also assessed for the liquid and compared to the specifications of marine fuels (standard ISO 8217). Gas chromatography was used to calculate the composition of the gaseous fraction. It was observed that all these properties remained practically invariable along the experiments without any significant technical problem. In addition, the reaction enthalpy necessary to perform the waste tire pyrolysis process (907.1 ± 40.0 kJ/kg) was determined from the combustion and formation enthalpies of waste tire and conversion products. Finally, a mass balance closure was performed showing an excellent reliability of the data obtained from the experimental campaign

Demonstration of the waste tire pyrolysis process on pilot scale in a continuous auger reactor

Energy Technology Data Exchange (ETDEWEB)

Martínez, Juan Daniel, E-mail: juand.martinez@upb.edu.co [Instituto de Carboquímica, ICB-CSIC, Miguel Luesma Castán 4, 50018, Zaragoza (Spain); Grupo de Investigaciones Ambientales, Instituto de Energía, Materiales y Medio Ambiente, Universidad Pontificia Bolivariana, Circular 1 N°70-01, Bloque 11, piso 2, Medellín (Colombia); Murillo, Ramón; García, Tomás; Veses, Alberto [Instituto de Carboquímica, ICB-CSIC, Miguel Luesma Castán 4, 50018, Zaragoza (Spain)

2013-10-15

Highlights: • The continuous pyrolysis of waste tire has been demonstrated at pilot scale in an auger reactor. • More than 500 kg of waste tires were processed in 100 operational hours. • The yields and characteristics of the pyrolysis products remained constant. • Mass and energy balances for an industrial scale plant are provided. • The reaction enthalpy necessary to perform the waste tire pyrolysis was determined. -- Abstract: This work shows the technical feasibility for valorizing waste tires by pyrolysis using a pilot scale facility with a nominal capacity of 150 kW{sub th}. A continuous auger reactor was operated to perform thirteen independent experiments that conducted to the processing of more than 500 kg of shredded waste tires in 100 h of operation. The reaction temperature was 550 °C and the pressure was 1 bar in all the runs. Under these conditions, yields to solid, liquid and gas were 40.5 ± 0.3, 42.6 ± 0.1 and 16.9 ± 0.3 wt.% respectively. Ultimate and proximate analyses as well as heating value analysis were conducted for both the solid and liquid fraction. pH, water content, total acid number (TAN), viscosity and density were also assessed for the liquid and compared to the specifications of marine fuels (standard ISO 8217). Gas chromatography was used to calculate the composition of the gaseous fraction. It was observed that all these properties remained practically invariable along the experiments without any significant technical problem. In addition, the reaction enthalpy necessary to perform the waste tire pyrolysis process (907.1 ± 40.0 kJ/kg) was determined from the combustion and formation enthalpies of waste tire and conversion products. Finally, a mass balance closure was performed showing an excellent reliability of the data obtained from the experimental campaign.

Thermal pyrolysis characteristics of macroalgae Cladophora glomerata.

Science.gov (United States)

Gao, Wenhua; Chen, Kefu; Zeng, Jinsong; Xu, Jun; Wang, Bin

2017-11-01

The Cladophora glomerata (C. glomerata) is a kind of widely distributed macroalgae in the freshwater ecosystems. It primarily consists of carbohydrates that can be converted into biofuel by pyrolysis. In this study, thermogravimetric analysis (TGA) was used to investigate the thermal behavior and kinetics of C. glomerata during the pyrolysis process. The results showed that heating rates slightly affect the decomposition properties of C. glomerata; with the heating rates increasing, the maximum peak of weight loss rate shifted to higher temperatures. The activation energies of C. glomerata pyrolysis reaction were 244.25 and 238.07kJ/mol, respectively, as calculated by Friedman and Kissinger-Akahira-Sunose (KAS) methods. The pre-exponential factor and reaction order were determined by Coats-Redfern model, and applied to simulate the pyrolysis process of C. glomerata. The model calculated data and experimental data were consistent. This study could provide theoretical supports for designing C. glomerata conversion processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Coal pyrolysis. VII. Economic viability of pyrolysis. Pirolisis del carbon. VII. Viabilidad economica de la pirolisis

Energy Technology Data Exchange (ETDEWEB)

Molinar, R.; Adanez, J.; Miranda, J.L.; Ibarra, J.V. (Instituto de Carboquimica, Zaragoza (Spain))

1989-04-01

Analyses the most important economic parameters of the main pyrolysis processes. Considers the markets available for semi-coke and tars. Concludes that no single technology or process has clear advantages over the others because all depends on the type of coal being used and the purpose for which the end product is to be used. Refers to studies carried out in Canada and the USA on the same subject and reports their findings. Concludes optimistically that coal pyrolysis shows promise of being economically viable in the future because although initially, costs reflect the high financial outlay necessary to begin operations, after a certain period, these costs fall and the end product can be sold at a lower price. A further point in favour of pyrolysis is that coal prices are likely to rise more slowly than oil prices. 5 refs., 8 tabs.

Temperature Jump Pyrolysis Studies of RP 2 Fuel

Science.gov (United States)

2017-01-09

Briefing Charts 3. DATES COVERED (From - To) 15 December 2016 – 11 January 2017 4. TITLE AND SUBTITLE Temperature Jump Pyrolysis Studies of RP-2 Fuel...Rev. 8- 98) Prescribed by ANSI Std. 239.18 1 TEMPERATURE JUMP PYROLYSIS STUDIES OF RP-2 FUEL Owen Pryor1, Steven D. Chambreau2, Ghanshyam L...17026 7 Temperature Jump Pyrolysis at AFRL Edwards Rapid heating of a metal filament at a rate of 600 – 800 K/s, and the set temperature is held for

Experimental investigation of pyrolysis process of corn straw

OpenAIRE

Lei Wang; Shengqiang Shen; Shuhua Yang; Xinguang Shi

2010-01-01

The present paper was performed to analyze the pyrolysis process of corn straw. Based on the thermogravimetric analysis, the component of pyrolysis gas of corn straw was tested using the gas chromatograph analyzer. Experimental results showed that, as the reaction temperature increases, the component of H 2 and CH 4 increases, whereas the component of CO and CO 2 decreases. Finally, the mechanism of pyrolysis process of corn straw was revealed from the point of view of the molecular structure...

Rapid quantification of biomarkers during kerogen microscale pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Stott, A.W.; Abbott, G.D. [Fossil Fuels and Environmental Geochemistry NRG, The University, Newcastle-upon-Tyne (United Kingdom)

1995-02-01

A rapid, reproducible method incorporating closed system microscale pyrolysis and thermal desorption-gas chromatography/mass spectrometry has been developed and applied to the quantification of sterane biomarkers released during pyrolysis of the Messel oil shale kerogen under confined conditions. This method allows a substantial experimental concentration-time data set to be collected at accurately controlled temperatures, due to the low thermal inertia of the microscale borosilicate glass reaction vessels, which facilitates kinetic studies of biomarker reactions during kerogen microscale pyrolysis

Sustainable Production of Bio-Combustibles from Pyrolysis of Agro-Industrial Wastes

Directory of Open Access Journals (Sweden)

Maurizio Volpe

2014-11-01

Full Text Available Evaluation of the sustainability of biomass pyrolysis requires a thorough assessment of the product yields and energy densities. With this purpose, a laboratory scale fixed bed reactor (FBR was adapted from the standard Gray-King (GK assay test on coal to conduct fixed bed pyrolysis experiments on agricultural and agro-industrial by-products. The present study provides results on the pyrolysis of two types of biomass: chipped olive tree trimmings (OT and olive pomace (OP. Solid (char and liquid (tar product yields are reported. Mass yields are determined and compared with values obtained in similar works. Results indicate that char yield decreases from 49% (OT-db and 50% (OP-db at 325 °C to 26% (OT db and 30% (OP-db at 650 °C. Tar yield is almost constant (42% at different reaction temperatures for OT, while it decreases slightly from 42% to 35% for OP. Energy density of the products at different peak temperatures is almost constant for OT (1.2, but slightly increases for OP (from a value of 1.3 to a value of 1.4.

Volatile organic emissions from the distillation and pyrolysis of vegetation

Directory of Open Access Journals (Sweden)

J. P. Greenberg

2006-01-01

Full Text Available Leaf and woody plant tissue (Pinus ponderosa, Eucalyptus saligna, Quercus gambelli, Saccharum officinarum and Oriza sativa were heated from 30 to 300°C and volatile organic compound (VOC emissions were identified and quantified. Major VOC emissions were mostly oxygenated and included acetic acid, furylaldehyde, acetol, pyrazine, terpenes, 2,3-butadione, phenol and methanol, as well as smaller emissions of furan, acetone, acetaldehyde, acetonitrile and benzaldehyde. Total VOC emissions from distillation and pyrolysis were on the order of 10 gC/kgC dry weight of vegetation, as much as 33% and 44% of CO2 emissions (gC(VOC/gC(CO2 measured during the same experiments, in air and nitrogen atmospheres, respectively. The emissions are similar in identity and quantity to those from smoldering combustion of woody tissue and of different character than those evolved during flaming combustion. VOC emissions from the distillation of pools and endothermic pyrolysis under low turbulence conditions may produce flammable concentrations near leaves and may facilitate the propagation of wildfires. VOC emissions from charcoal production are also related to distillation and pyrolysis; the emissions of the highly reactive VOCs from production are as large as the carbon monoxide emissions.

Insights into pyrolysis and co-pyrolysis of biomass and polystyrene: Thermochemical behaviors, kinetics and evolved gas analysis

International Nuclear Information System (INIS)

Özsin, Gamzenur; Pütün, Ayşe Eren

2017-01-01

Highlights: • TGA/MS/FT-IR was used to explore effect of polystyrene on pyrolytic decomposition of biomass. • The model-free iso-conversional methods were used for kinetic analysis. • Interactions occurred depending on the characteristics of the biomass. • TGA/MS and TGA/FT-IR coupling were used for gas analysis of co-pyrolysis for the first time. - Abstract: The purpose of this study was to investigate the effect on polystyrene (PS) during co-pyrolysis with biomass through thermal decomposition. The model-free iso-conversional methods (Kissinger, Friedman, Flynn-Wall-Ozawa, Kissinger-Akahira-Sunose, Starink and Vyazovkin) were adopted to calculate activation energy of the pyrolysis and co-pyrolysis process of two biomass samples (walnut shell: WS and peach stones: PST) with PS. It is found that biomass blending to PS decreased activation energy values and resulted in multi-step reaction mechanisms. Furthermore, changes in the evolution profiles of methyl, water, methoxy, carbon dioxide, benzene and styrene was monitored through evolved gas analysis via TGA/FT-IR and TGA/MS. Detection of temperature dependent release of volatiles indicated the differences occur as a result of compositional differences of biomass.

Pyrolysis of Spent Ion Exchange Resins

International Nuclear Information System (INIS)

Braehler, Georg; Slametschka, Rainer

2012-09-01

and is disposed of as medium level waste. The organic components pass into the pyrolysis gas which is burnt. The flue gas is further cleaned. TBP pyrolysis facilities have been built in France (La Hague), Belgium (Mol) and in Japan (Rokkashomura). The Belgian plant has recently ceased operating as all the TBP arising from Eurochemic operations had been successfully processed. The facility in Japan is in the commissioning stage. Many experiments have been carried out at the existing facilities, and also in corresponding pilot plants including NUKEM's own, to extend the range of waste that can be processed. Initial tests have shown that IEX can be decomposed by pyrolysis with very good results, yielding an inert and chemically resistant product. No additives are necessary. The main constituent of the product, the pyrolysate or ash, is carbon. It has been discovered that the entire radioactive inventory remains in the pyrolysate during pyrolysis of the IEX. This is achieved by relatively low process temperatures that prevent highly volatile nuclides such as the cesium nuclides from passing into the gaseous phase. Sintered metal filters in pyrolysis plant ensure that even the radioactivity bonded to the dust remains in the pyrolysate. In addition to the radionuclides, the main constituents of the residue are carbon from the original polystyrene matrix and sulphur from the functional groups. The pyrolysate occurs as a flowable solid material and not as a melt. It is thus easy to handle and can be compressed or cemented, depending on the requirements for interim and permanent storage. Any further constituents such as inorganic filter materials or even other organic materials do not interfere with the process, they are dried, calcined or also pyrolyzed. Hydrocarbons such as methane or propene, steam and low volumes of ammonia are the products in gaseous form. The pyrolysis gas generated must be burnt in a burner and then passed to the emission control system and the

Pyrolysis Strategies for Effective Utilization of Lignocellulosic and Algal Biomass

Science.gov (United States)

Maddi, Balakrishna

-of-concept micro-pyrolyser (Pyroprobe) and lab-scale fixed-bed experiments were performed using oleaginous algae (Chlorella Sp.) to establish pyrolytic fractionation technique and also to determine the yields of triglyceride-specific bio-oils. As expected, triglyceride-specific bio-oils have hydrocarbons and free fatty acids that were nearly free of water, organic acids and carbohydrate degradation products. Another unique feature of the fractional pyrolysis method is that it allows upgrading of the triglyceride-specific bio-oil vapors via in situ gas-phase hydro-deoxygenation to drop-in fuels (hydrocarbons), without the need to condense the vapors. Similarly, these vapors can also be converted to other value-added products such as fatty acid methyl esters and amides though efficient catalytic and non-catalytic in situ gas-phase conversion methods. Energy requirements for this new pyrolytic fractionation method were also assessed, using energy estimates for the individual steps obtained via differential scanning calorimetry experiments. A comparison of these energy needs against those of alternative thermal processing methods of algae (hydro-thermal processing) proposed in the literature established the viability of this new method. Finally, a new TGA-based analytical method was developed in this thesis for rapid quantification of the triglyceride content of oleaginous feed stocks, by exploiting the non-overlapping thermal degradation range of triglycerides and the other major components.

NMR spectroscopy of coal pyrolysis products

Energy Technology Data Exchange (ETDEWEB)

Polonov, V.M.; Kalabin, G.A.; Kushnarev, D.F.; Shevchenko, G.G.

1985-12-01

The authors consider the scope for using H 1 and C 13 NMR spectroscopy to describe the products from coal pyrolysis and hydrogenization. The accuracy of the structural information provided by the best NMR methods is also considered. The stuctural parameters derived from H 1 and C 13 NMR spectra are presented. Results demonstrate the high accuracy and sensitivity of the structural information provided by H 1 AND C 13 NMR spectra for coal products. There are substantial structural differences between the soluble products from medium-temperature coking of Cheremkhov coal and high-speed pyrolysis of Kan-Acha coal, and also differences in behavior during hydrogenation. These differences are related to the structure of the organic matter in the initial coal and to differences in the pyrolysis mechanisms.

Evaluation of pyrolysis curves for volatile elements in aqueous standards and carbon-containing matrices in electrothermal vaporization inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Silva, A.F. [Delft University of Technology, Faculty of Applied Sciences, DelftChemTech, Julianalaan 136, 2628 BL Delft (Netherlands); Universidade Federal de Santa Catarina, Departamento de Quimica, 88040-900 Florianopolis, SC (Brazil); Welz, B. [Universidade Federal de Santa Catarina, Departamento de Quimica, 88040-900 Florianopolis, SC (Brazil); Loos-Vollebregt, M.T.C. de [Delft University of Technology, Faculty of Applied Sciences, DelftChemTech, Julianalaan 136, 2628 BL Delft (Netherlands)], E-mail: m.t.c.deloos-vollebregt@tudelft.nl

2008-07-15

Pyrolysis curves in electrothermal atomic absorption spectrometry (ET AAS) and electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) have been compared for As, Se and Pb in lobster hepatopancreas certified reference material using Pd/Mg as the modifier. The ET AAS pyrolysis curves confirm that the analytes are not lost from the graphite furnace up to a pyrolysis temperature of 800 deg. C. Nevertheless, a downward slope of the pyrolysis curve was observed for these elements in the biological material using ETV-ICP-MS. This could be related to a gain of sensitivity at low pyrolysis temperatures due to the matrix, which can act as carrier and/or promote changes in the plasma ionization equilibrium. Experiments with the addition of ascorbic acid to the aqueous standards confirmed that the higher intensities obtained in ETV-ICP-MS are related to the presence of organic compounds in the slurry. Pyrolysis curves for As, Se and Pb in coal and coal fly ash were also investigated using the same Pd/Mg modifier. Carbon intensities were measured in all samples using different pyrolysis temperatures. It was observed that pyrolysis curves for the three analytes in all slurry samples were similar to the corresponding graphs that show the carbon intensity for the same slurries for pyrolysis temperatures from 200 deg. C up to 1000 deg. C.

Low oxygen biomass-derived pyrolysis oils and methods for producing the same

Science.gov (United States)

Marinangeli, Richard; Brandvold, Timothy A; Kocal, Joseph A

2013-08-27

Low oxygen biomass-derived pyrolysis oils and methods for producing them from carbonaceous biomass feedstock are provided. The carbonaceous biomass feedstock is pyrolyzed in the presence of a catalyst comprising base metal-based catalysts, noble metal-based catalysts, treated zeolitic catalysts, or combinations thereof to produce pyrolysis gases. During pyrolysis, the catalyst catalyzes a deoxygenation reaction whereby at least a portion of the oxygenated hydrocarbons in the pyrolysis gases are converted into hydrocarbons. The oxygen is removed as carbon oxides and water. A condensable portion (the vapors) of the pyrolysis gases is condensed to low oxygen biomass-derived pyrolysis oil.

Pyrolysis and Gasification

DEFF Research Database (Denmark)

Astrup, Thomas; Bilitewski, B.

2011-01-01

a waste management perspective, pyrolysis and gasification are of relatively little importance as an overall management option. Today, gasification is primarily used on specific waste fractions as opposed to mixed household wastes. The main commercial activity so far has been in Japan, with only limited....... Today gasification is used within a range of applications, the most important of which are conversion of coal into syngas for use as chemical feedstock or energy production; but also gasification of biomass and waste is gaining significant interest as emerging technologies for sustainable energy. From...... success in Europe and North America (Klein et al., 2004). However, pyrolysis and gasification of waste are generally expected to become more widely used in the future. A main reason for this is that public perceptions of waste incineration in some countries is a major obstacle for installing new...

[Influence of impurities on waste plastics pyrolysis: products and emissions].

Science.gov (United States)

Zhao, Lei; Wang, Zhong-Hui; Chen, De-Zhen; Ma, Xiao-Bo; Luan, Jian

2012-01-01

The study is aimed to evaluate the impact of impurities like food waste, paper, textile and especially soil on the pyrolysis of waste plastics. For this purpose, emissions, gas and liquid products from pyrolysis of waste plastics and impurities were studied, as well as the transfer of element N, Cl, S from the substrates to the pyrolysis products. It was found that the presence of food waste would reduce the heat value of pyrolysis oil to 27 MJ/kg and increase the moisture in the liquid products, therefore the food residue should be removed from waste plastics; and the soil, enhance the waste plastics' pyrolysis by improving the quality of gas and oil products. The presence of food residue, textile and paper leaded to higher gas emissions.

Oxidative desulfurization of tire pyrolysis oil

OpenAIRE

Ahmad Shahzad; Ahmad Muhammad Imran; Naeem Khawar; Humayun Muhammad; Sebt-E-Zaeem; Faheem Farrukh

2016-01-01

This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure a...

Self-activation of biochar from furfural residues by recycled pyrolysis gas.

Science.gov (United States)

Yin, Yulei; Gao, Yuan; Li, Aimin

2018-04-17

Biochar samples with controllable specific surface area and mesopore ratio were self-activated from furfural residues by recycled pyrolysis gas. The objective of this study was to develop a new cyclic utilization method for the gas produced by pyrolysis. The influences of preparation parameters on the resulting biochar were studied by varying the pyrolysis-gas flow rate, activation time and temperature. Structural characterization of the produced biochar was performed by analysis of nitrogen adsorption isotherms at 77 K and scanning electron microscope (SEM). The pyrolysis gas compositions before and after activation were determined by a gas chromatograph. The results indicated that the surface area of the biochar was increased from 167 m 2 /g to 567 m 2 /g, the total pore volume increased from 0.121 cm 3 /g to 0.380 cm 3 /g, and the ratio of the mesopore pore volume to the total pore volume increased 17-39.7%. The CO volume fraction of the pyrolysis gas changed from 34.66 to 62.29% and the CO 2 volume fraction decreased from 48.26% to 12.17% under different conditions of pyrolysis-gas flow rate, activation time and temperature. The calorific values of pyrolysis gas changed from 8.82 J/cm 3 to 14.00 J/cm 3 , which were higher than those of conventional pyrolysis gases. The slower pyrolysis-gas flow rate and higher activation time increased the efficiency of the reaction between carbon and pyrolysis gas. These results demonstrated the feasibility of treatment of the furfural residues to produce microporous and mesoporous biochar. The pyrolysis gas that results from the activation process could be used as fuel. Overall, this new self-activation method meets the development requirements of cyclic economy and cleaner production. Copyright © 2018. Published by Elsevier Ltd.

Bacterial transport in heterogeneous porous media: Observations from laboratory experiments

Science.gov (United States)

Silliman, S. E.; Dunlap, R.; Fletcher, M.; Schneegurt, M. A.

2001-11-01

Transport of bacteria through heterogeneous porous media was investigated in small-scale columns packed with sand and in a tank designed to allow the hydraulic conductivity to vary as a two-dimensional, lognormally distributed, second-order stationary, exponentially correlated random field. The bacteria were Pseudomonas ftuorescens R8, a strain demonstrating appreciable attachment to surfaces, and strain Ml, a transposon mutant of strain R8 with reduced attachment ability. In bench top, sand-filled columns, transport was determined by measuring intensity of fluorescence of stained cells in the effluent or by measuring radiolabeled cells that were retained in the sand columns. Results demonstrated that strain Ml was transported more efficiently than strain R8 through columns packed with either a homogeneous silica sand or a more heterogeneous sand with iron oxide coatings. Two experiments conducted in the tank involved monitoring transport of bacteria to wells via sampling from wells and sample ports in the tank. Bacterial numbers were determined by direct plate count. At the end of the first experiment, the distribution of the bacteria in the sediment was determined by destructive sampling and plating. The two experiments produced bacterial breakthrough curves that were quite similar even though the similarity between the two porous media was limited to first- and second-order statistical moments. This result appears consistent with the concept of large-scale, average behavior such as has been observed for the transport of conservative chemical tracers. The transported bacteria arrived simultaneously with a conservative chemical tracer (although at significantly lower normalized concentration than the tracer). However, the bacterial breakthrough curves showed significant late time tailing. The concentrations of bacteria attached to the sediment surfaces showed considerably more spatial variation than did the concentrations of bacteria in the fluid phase. This

Flash pyrolysis properties of algae and lignin residue

DEFF Research Database (Denmark)

Trinh, Ngoc Trung; Jensen, Peter Arendt; Sørensen, Hanne Risbjerg

of macroalgae showed a promising result with on yield of 54 wt% dry ash free basis (daf) and 78% energy recovery in the bio-oil. The physiochemical properties of the bio-oils were characterized with respect to higher heating value, molecular mass distribution, viscosity, pH, density and elemental compositions......A fast pyrolysis study on lignin and macroalgae (non-conventional biomass) and wood and straw (conventional biomass) were carried out in a pyrolysis centrifugal reactor. The product distributions and energy recoveries were measured and compared among these biomasses. The fast pyrolysis...

Catalytic pyrolysis using UZM-44 aluminosilicate zeolite

Science.gov (United States)

Nicholas, Christopher P; Boldingh, Edwin P

2013-12-17

A new family of aluminosilicate zeolites designated UZM-44 has been synthesized. These zeolites are represented by the empirical formula Na.sub.nM.sub.m.sup.k+T.sub.tAl.sub.1-xE.sub.xSi.sub.yO.sub.z where "n" is the mole ratio of Na to (Al+E), M represents a metal or metals from zinc, Group 1, Group 2, Group 3 and or the lanthanide series of the periodic table, "m" is the mole ratio of M to (Al+E), "k" is the average charge of the metal or metals M, T is the organic structure directing agent or agents, and E is a framework element such as gallium. The process involves contacting a carbonaceous biomass feedstock with UZM-44 at pyrolysis conditions to produce pyrolysis gases comprising hydrocarbons. The catalyst catalyzes a deoxygenation reaction converting oxygenated hydrocarbons into hydrocarbons and removing the oxygen as carbon oxides and water. A portion of the pyrolysis gases is condensed to produce low oxygen biomass-derived pyrolysis oil.

Enhancing biochar yield by co-pyrolysis of bio-oil with biomass: impacts of potassium hydroxide addition and air pretreatment prior to co-pyrolysis.

Science.gov (United States)

Veksha, Andrei; Zaman, Waheed; Layzell, David B; Hill, Josephine M

2014-11-01

The influence of KOH addition and air pretreatment on co-pyrolysis (600 °C) of a mixture of bio-oil and biomass (aspen wood) was investigated with the goal of increasing biochar yield. The bio-oil was produced as a byproduct of the pyrolysis of biomass and recycled in subsequent runs. Co-pyrolysis of the biomass with the recycled bio-oil resulted in a 16% mass increase in produced biochar. The yields were further increased by either air pretreatment or KOH addition prior to co-pyrolysis. Air pretreatment at 220 °C for 3 h resulted in the highest mass increase (32%) compared to the base case of pyrolysis of biomass only. No synergistic benefit was observed by combining KOH addition with air pretreatment. In fact, KOH catalyzed reactions that increased the bed temperature resulting in carbon loss via formation of CO and CO2. Copyright © 2014 Elsevier Ltd. All rights reserved.

Thermodynamic analyses of hydrogen production from sub-quality natural gas. Part I: Pyrolysis and autothermal pyrolysis

Science.gov (United States)

Huang, Cunping; T-Raissi, Ali

Sub-quality natural gas (SQNG) is defined as natural gas whose composition exceeds pipeline specifications of nitrogen, carbon dioxide (CO 2) and/or hydrogen sulfide (H 2S). Approximately one-third of the U.S. natural gas resource is sub-quality gas [1]. Due to the high cost of removing H 2S from hydrocarbons using current processing technologies, SQNG wells are often capped and the gas remains in the ground. We propose and analyze a two-step hydrogen production scheme using SQNG as feedstock. The first step of the process involves hydrocarbon processing (via steam-methane reformation, autothermal steam-methane reformation, pyrolysis and autothermal pyrolysis) in the presence of H 2S. Our analyses reveal that H 2S existing in SQNG is stable and can be considered as an inert gas. No sulfur dioxide (SO 2) and/or sulfur trioxide (SO 3) is formed from the introduction of oxygen to SQNG. In the second step, after the separation of hydrogen from the main stream, un-reacted H 2S is used to reform the remaining methane, generating more hydrogen and carbon disulfide (CS 2). Thermodynamic analyses on SQNG feedstock containing up to 10% (v/v) H 2S have shown that no H 2S separation is required in this process. The Part I of this paper includes only thermodynamic analyses for SQNG pyrolysis and autothermal pyrolysis.

Upgrading biomass pyrolysis bio-oil to renewable fuels.

Science.gov (United States)

2015-01-01

Fast pyrolysis is a process that can convert woody biomass to a crude bio-oil (pyrolysis oil). However, some of these compounds : contribute to bio-oil shelf life instability and difficulty in refining. Catalytic hydrodeoxygenation (HDO) of the bio-o...

Rapid and slow pyrolysis of pistachio shell: effect of pyrolysis conditions on the product yields and characterization of the liquid product

Energy Technology Data Exchange (ETDEWEB)

Putun, Ayse E [Department of Chemical Engineering, Anadolu University, Eskisehir 26470, (Turkey); Ozbay, Nurgul [Bozuyuk Vocational School, Anadolu University, Bozuyuk/Bilecik, (Turkey); Varol, Esin Apaydin; Uzun, Basak B; Ates, Fuda [Department of Chemical Engineering, Anadolu University, Eskisehir 26470, (Turkey)

2006-10-30

This study reports the experimental results for the pyrolysis of pistachio shell under different conditions in a tubular reactor under a nitrogen flow. For the different conditions of pyrolysis temperature, nitrogen flow rate and heating rate, pyrolysis temperature of 773 K gave the highest bio-oil yield with a value of 27.7% when the heating rate and carrier gas flow rate were chosen as 300 K min{sup -1} and 100 cm{sup 3} min{sup -1}, respectively. Column chromatography was applied to this bio-oil and its subfractions were characterized by elemental analysis, FT-IR and 1H-NMR. Aliphatic subfraction was conducted to gas chromatography-mass spectroscopy for further characterization. The results for the characterization show that using pistachio shell as a renewable source to produce valuable liquid products is applicable via pyrolysis. (Author)

Combustion Properties of Biomass Flash Pyrolysis Oils: Final Project Report

Energy Technology Data Exchange (ETDEWEB)

C. R. Shaddix; D. R. Hardesty

1999-04-01

Thermochemical pyrolysis of solid biomass feedstocks, with subsequent condensation of the pyrolysis vapors, has been investigated in the U.S. and internationally as a means of producing a liquid fuel for power production from biomass. This process produces a fuel with significantly different physical and chemical properties from traditional petroleum-based fuel oils. In addition to storage and handling difficulties with pyrolysis oils, concern exists over the ability to use this fuel effectively in different combustors. The report endeavors to place the results and conclusions from Sandia's research into the context of international efforts to utilize pyrolysis oils. As a special supplement to this report, Dr. Steven Gust, of Finland's Neste Oy, has provided a brief assessment of pyrolysis oil combustion research efforts and commercialization prospects in Europe.

Bacterial Transport in Heterogeneous Porous Media: Laboratory and Field Experiments

Science.gov (United States)

Fuller, M. E.

2001-12-01

A fully instrumented research site for examining field-scale bacterial transport has been established on the eastern shore of Virginia. Studies employing intact sediment cores from the South Oyster site have been performed to examine the effects of physical and chemical heterogeneity, to derive transport parameters, and to aid in the selection of bacterial strains for use in field experiments. A variety of innovative methods for tracking bacteria were developed and evaluated under both laboratory and field conditions, providing the tools to detect target cell concentrations in groundwater down to effects of physical and chemical heterogeneity on field-scale bacterial transport. The results of this research not only contribute to the development of more effective bioremediation strategies, but also have implications for a better understanding of bacterial movement in the subsurface as it relates to public health microbiology and general microbial ecology.

Bio-Oil Production from Fast Pyrolysis of Corn Wastes and Eucalyptus Wood in a Fluidized Bed Reactor

Directory of Open Access Journals (Sweden)

M.A Ebrahimi-Nik

2014-09-01

Full Text Available Fast pyrolysis is an attractive technology for biomass conversion, from which bio-oil is the preferred product with a great potential for use in industry and transport. Corn wastes (cob and stover and eucalyptus wood are widely being produced throughout the world. In this study, fast pyrolysis of these two materials were examined under the temperature of 500 °C; career gas flow rate of 660 l h-1; particle size of 1-2 mm; 80 and 110 g h-1 of feed rate. The experiments were carried out in a continuous fluidized bed reactor. Pyrolysis vapor was condensed in 3 cooling traps (15, 0 and -40 °C plus an electrostatic one. Eucalyptus wood was pyrolyised to 12.4, 61.4, and 26.2 percent of bio-char, bio-oil and gas, respectively while these figures were as 20.15, 49.9, and 29.95 for corn wastes. In all experiments, the bio-oil obtained from electrostatic trap was a dark brown and highly viscose liquid.

Design of an automated solar concentrator for the pyrolysis of scrap rubber

International Nuclear Information System (INIS)

Zeaiter, Joseph; Ahmad, Mohammad N.; Rooney, David; Samneh, Bechara; Shammas, Elie

2015-01-01

Highlights: • Design of a solar concentrator with high focal-point temperatures. • Development of an automated continuous solar tracking system. • Catalytic pyrolysis to convert waste rubber tire to gas and liquid products. • The liquid components had high yields of C 10 –C 29 hydrocarbons. • The gaseous components were mainly propene and cyclobutene. - Abstract: An automated solar reactor system was designed and built to carry out catalytic pyrolysis of scrap rubber tires at 550 °C. To maximize solar energy concentration, a two degrees-of-freedom automated sun tracking system was developed and implemented. Both the azimuth and zenith angles were controlled via feedback from six photo-resistors positioned on a Fresnel lens. The pyrolysis of rubber tires was tested with the presence of two types of acidic catalysts, H-beta and H-USY. Additionally, a photoactive TiO 2 catalyst was used and the products were compared in terms of gas yields and composition. The catalysts were characterized by BET analysis and the pyrolysis gases and liquids were analyzed using GC–MS. The oil and gas yields were relatively high with the highest gas yield reaching 32.8% with H-beta catalyst while TiO 2 gave the same results as thermal pyrolysis without any catalyst. In the presence of zeolites, the dominant gasoline-like components in the gas were propene and cyclobutene. The TiO 2 and non-catalytic experiments produced a gas containing gasoline-like products of mainly isoprene (76.4% and 88.4% respectively). As for the liquids they were composed of numerous components spread over a wide distribution of C 10 to C 29 hydrocarbons of naphthalene and cyclohexane/ene derivatives

Modeling of the pyrolysis of biomass under parabolic and exponential temperature increases using the Distributed Activation Energy Model

International Nuclear Information System (INIS)

Soria-Verdugo, Antonio; Goos, Elke; Arrieta-Sanagustín, Jorge; García-Hernando, Nestor

2016-01-01

Highlights: • Pyrolysis of biomass under parabolic and exponential temperature profiles is modeled. • The model is based on a simplified Distributed Activation Energy Model. • 4 biomasses are analyzed in TGA with parabolic and exponential temperature increases. • Deviations between the model prediction and TGA measurements are under 5 °C. - Abstract: A modification of the simplified Distributed Activation Energy Model is proposed to simulate the pyrolysis of biomass under parabolic and exponential temperature increases. The pyrolysis of pine wood, olive kernel, thistle flower and corncob was experimentally studied in a TGA Q500 thermogravimetric analyzer. The results of the measurements of nine different parabolic and exponential temperature increases for each sample were employed to validate the models proposed. The deviation between the experimental TGA measurements and the estimation of the reacted fraction during the pyrolysis of the four samples under parabolic and exponential temperature increases was lower than 5 °C for all the cases studied. The models derived in this work to describe the pyrolysis of biomass with parabolic and exponential temperature increases were found to be in good agreement with the experiments conducted in a thermogravimetric analyzer.

Co-pyrolysis of low rank coals and biomass: Product distributions

Energy Technology Data Exchange (ETDEWEB)

Soncini, Ryan M.; Means, Nicholas C.; Weiland, Nathan T.

2013-10-01

Pyrolysis and gasification of combined low rank coal and biomass feeds are the subject of much study in an effort to mitigate the production of green house gases from integrated gasification combined cycle (IGCC) systems. While co-feeding has the potential to reduce the net carbon footprint of commercial gasification operations, the effects of co-feeding on kinetics and product distributions requires study to ensure the success of this strategy. Southern yellow pine was pyrolyzed in a semi-batch type drop tube reactor with either Powder River Basin sub-bituminous coal or Mississippi lignite at several temperatures and feed ratios. Product gas composition of expected primary constituents (CO, CO{sub 2}, CH{sub 4}, H{sub 2}, H{sub 2}O, and C{sub 2}H{sub 4}) was determined by in-situ mass spectrometry while minor gaseous constituents were determined using a GC-MS. Product distributions are fit to linear functions of temperature, and quadratic functions of biomass fraction, for use in computational co-pyrolysis simulations. The results are shown to yield significant nonlinearities, particularly at higher temperatures and for lower ranked coals. The co-pyrolysis product distributions evolve more tar, and less char, CH{sub 4}, and C{sub 2}H{sub 4}, than an additive pyrolysis process would suggest. For lignite co-pyrolysis, CO and H{sub 2} production are also reduced. The data suggests that evolution of hydrogen from rapid pyrolysis of biomass prevents the crosslinking of fragmented aromatic structures during coal pyrolysis to produce tar, rather than secondary char and light gases. Finally, it is shown that, for the two coal types tested, co-pyrolysis synergies are more significant as coal rank decreases, likely because the initial structure in these coals contains larger pores and smaller clusters of aromatic structures which are more readily retained as tar in rapid co-pyrolysis.

PYROLYSIS OF ISOCHRYSIS MICROALGAE WITH METAL OXIDE CATALYSTS FOR BIO-OIL PRODUCTION

Directory of Open Access Journals (Sweden)

TEVFİK AYSU

2016-12-01

Full Text Available Pyrolysis of Isochrysis microalgae was carried out in a fixed-bed reactor without and with metal oxide catalysts (CeO2, TiO2, Al2O3 at the temperatures of 450, 500 and 550 oC with a constant heating rate of 40 oC/min. The pyrolysis conditions including catalyst and temperature were studied in terms of their effects on the yields of pyrolysis products and quality. The amount of bio-char, bio-oil and gas products was calculated. The composition of the produced bio-oils was determined by Elemental analysis (EA, Fourier transform infrared spectroscopy (FT-IR, proton nuclear magnetic resonance (1H NMR and Gas chromatography/mass spectrometry (GC–MS techniques. As a result of the pyrolysis experiments, it is shown that there have been significant effects of both catalyst and temperature on the conversion of Isochrysis microalgae into solid, liquid (bio-oil and gas products. The highest bio-oil yield (24.30 % including aqueous phase was obtained in the presence of TiO2 (50% as catalyst at 500 °C. 98 different compounds were identified by GC-MS in bio-oils obtained at 500 oC. According to 1H NMR analysis, bio-oils contained ∼60-64 % aliphatic and ∼17-19 % aromatic structural units. EA showed that the bio-oils contained ∼66-69 % C and having 31-34 MJ/kg higher heating values.

Toxicity of pyrolysis gases from polyether sulfone

Science.gov (United States)

Hilado, C. J.; Olcomendy, E. M.

1979-01-01

A sample of polyether sulfone was evaluated for toxicity of pyrolysis gases, using the toxicity screening test method developed at the University of San Francisco. Animal response times were relatively short at pyrolysis temperatures of 600 to 800 C, with death occurring within 6 min. The principal toxicant appeared to be a compound other than carbon monoxide.

Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants

Energy Technology Data Exchange (ETDEWEB)

Adrados, A., E-mail: aitziber.adrados@ehu.es [Chemical and Environmental Engineering Department, School of Engineering of Bilbao, Alameda. Urquijo s/n, 48013 Bilbao (Spain); De Marco, I.; Lopez-Urionabarrenechea, A.; Caballero, B.M.; Laresgoiti, M.F. [Chemical and Environmental Engineering Department, School of Engineering of Bilbao, Alameda. Urquijo s/n, 48013 Bilbao (Spain)

2013-01-15

Highlights: Black-Right-Pointing-Pointer Study of the influence of materials in the pyrolysis of real plastic waste samples. Black-Right-Pointing-Pointer Inorganic compounds remain unaltered. Black-Right-Pointing-Pointer Cellulosic components give rise to an increase in char formation. Black-Right-Pointing-Pointer Cellulosic components promote the production of aqueous phase. Black-Right-Pointing-Pointer Cellulosic components increase CO and CO{sub 2} contents in the gases. - Abstract: In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm{sup 3} reactor, swept with 1 L min{sup -1} N{sub 2}, at 500 Degree-Sign C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33-40 MJ kg{sup -1}). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO{sub 2}; their HHV is in the range of 18-46 MJ kg{sup -1}. The amount of CO-CO{sub 2} increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char.

Method of pyrolysis for spent ion-exchange resins

International Nuclear Information System (INIS)

Aoyama, Yoshiyuki; Matsuda, Masami; Kawamura, Fumio; Yusa, Hideo.

1985-01-01

Purpose: To prevent the generation of noxious sulfur oxide and ammonia on the pyrolysis for spent ion-exchange resins discharged from nuclear power plants. Method: In the case where the pyrolysis is made for the cationic exchange resins having sulfonic acids as the ion-exchange group, alkali metals or alkaline earth metals capable of reacting with sulfonic acid groups to form solid sulfates are previously deposited by way of ion-exchange reactions prior to the pyrolysis. In another case of the anionic exchange resins having quarternary ammonium groups as the ion-exchange groups, halogenic elements capable of reacting with the ammonium groups to form solid ammonium salts are deposited to the ion-exchange resins through ion-exchange reactions prior to the pyrolysis. As a result, the amount of the binders used can be reduced, and this method can be used in a relatively simple processing facility. (Horiuchi, T.)

Renewable hydrocarbons for jet fuels from biomass and plastics via microwave-induced pyrolysis and hydrogenation processes

Science.gov (United States)

Zhang, Xuesong

This dissertation aims to enhance the production of aromatic hydrocarbons in the catalytic microwave-induced pyrolysis, and maximize the production of renewable cycloalkanes for jet fuels in the hydrogenation process. In the process, ZSM-5 catalyst as the highly efficient catalyst was employed for catalyzing the pyrolytic volatiles from thermal decomposition of cellulose (a model compound of lignocellulosic biomass). A central composite experiment design (CCD) was used to optimize the product yields as a function of independent factors (e.g. catalytic temperature and catalyst to feed mass ratio). The low-density polyethylene (a mode compound of waste plastics) was then carried out in the catalytic microwave-induced pyrolysis in the presence of ZSM-5 catalyst. Thereafter, the catalytic microwave-induced co-pyrolysis of cellulose with low-density polyethylene (LDPE) was conducted over ZSM-5 catalyst. The results showed that the production of aromatic hydrocarbons was significantly enhanced and the coke formation was also considerably reduced comparing with the catalytic microwave pyrolysis of cellulose or LDPE alone. Moreover, practical lignocellulosic biomass (Douglas fir sawdust pellets) was converted into aromatics-enriched bio-oil by catalytic microwave pyrolysis. The bio-oil was subsequently hydrogenated by using the Raney Ni catalyst. A liquid-liquid extraction step was implemented to recover the liquid organics and remove the water content. Over 20% carbon yield of liquid product regarding lignocellulosic biomass was obtained. Up to 90% selectivity in the liquid product belongs to jet fuel range cycloalkanes. As the integrated processes was developed, catalytic microwave pyrolysis of cellulose with LDPE was conducted to improve aromatic production. After the liquid-liquid extraction by the optimal solvent (n-heptane), over 40% carbon yield of hydrogenated organics based on cellulose and LDPE were achieved in the hydrogenation process. As such, real

Pyrolysis of D-Glucose to Acrolein

Science.gov (United States)

Shen, Chong; Zhang, Igor Ying; Fu, Gang; Xu, Xin

2011-06-01

Despite of its great importance, the detailed molecular mechanism for carbohydrate pyrolysis remains poorly understood. We perform a density functional study with a newly developed XYG3 functional on the processes for D-glucose pyrolysis to acrolein. The most feasible reaction pathway starts from an isomerization from D-glucose to D-fructose, which then undergoes a cyclic Grob fragmentation, followed by a concerted electrocyclic dehydration to yield acrolein. This mechanism can account for the known experimental results.

Theoretical study of the pyrolysis of vanillin as a model of secondary lignin pyrolysis

Science.gov (United States)

Wang, Meng; Liu, Chao; Xu, Xiaoxiao; Li, Qibin

2016-06-01

The unimolecular and bimolecular decomposition reactions in processes of vanillin pyrolysis were theoretically investigated by employing density functional theory (DFT) method at M06-2X/6-31 G+(d,p) level. The result shows that the homolytic cleavage of O-CH3 bond could be the dominant initial step in the pyrolysis of vanillin. The hydrogen abstractions from functional groups of vanillin by the formed radicals play important roles in the formation of main products. Both formyl, hydroxyl and methoxyl group contribute to the formation of CO. Benzene is formed from the hydrogen addition reaction between hydrogen radical and phenol at high temperature.

Bio-oil from Flash Pyrolysis of Agricultural Residues

DEFF Research Database (Denmark)

Ibrahim, Norazana

This thesis describes the production of bio-oils from flash pyrolysis of agricultural residues, using a pyrolysis centrifugal reactor (PCR). By thermal degradation of agricultural residues in the PCR, a liquid oil, char and non-condensable gases are produced. The yield of each fraction...

Fast pyrolysis of hardwood residues using a fixed bed drop-type pyrolyzer

International Nuclear Information System (INIS)

Mazlan, Mohammad Amir Firdaus; Uemura, Yoshimitsu; Osman, Noridah B.; Yusup, Suzana

2015-01-01

Highlights: • Pyrolysis of rubber and Meranti wood was conducted by using a drop-type pyrolyzer. • As temperature increase, char yield decrease, but bio-oil and gas yield increase. • Maximum pyrolysis temperature for pyrolysis of RWS is 550 °C and 600 °C for MWS. • Calorific value of bio-char is very high and potential to be used as a solid fuel. • CO and CO 2 are the major gas components in the non-condensable gases by-product. - Abstract: In this research, rubber wood sawdust (RWS) and Meranti wood sawdust (MWS) were pyrolyzed in a fixed bed drop-type pyrolyzer under an inert condition. The first part of the study is to determine the influence of pyrolysis temperature (450, 500, 550, 600, 650 °C) on the yield of pyrolysis products. Pyrolysis of these different residues generate an almost identical maximum amount of bio-oil close to 33 wt.%, but at different maximum temperature (550 °C for pyrolysis of RWS and 600 °C for pyrolysis of MWS). To evaluate the effect of biomass type on the composition and characterization of pyrolysis products, the second part involves the analyses of pyrolysis products from the maximum pyrolysis temperature. Acetic acid, tetrahydrofuran, and benzene were the main bio-oil components. The bio-oil contained high percentage of oxygen and hydrogen, indicating high water content in the bio-oil. High amount of water in bio-oil significantly reduced its calorific value. Under extensive heating, particle size of the bio-char from SEM images decreased due to breakage and shrinkage mechanisms. The major components of non-condensable gases were CO and CO 2

Solar coal gasification reactor with pyrolysis gas recycle

Science.gov (United States)

Aiman, William R.; Gregg, David W.

1983-01-01

Coal (or other carbonaceous matter, such as biomass) is converted into a duct gas that is substantially free from hydrocarbons. The coal is fed into a solar reactor (10), and solar energy (20) is directed into the reactor onto coal char, creating a gasification front (16) and a pyrolysis front (12). A gasification zone (32) is produced well above the coal level within the reactor. A pyrolysis zone (34) is produced immediately above the coal level. Steam (18), injected into the reactor adjacent to the gasification zone (32), reacts with char to generate product gases. Solar energy supplies the energy for the endothermic steam-char reaction. The hot product gases (38) flow from the gasification zone (32) to the pyrolysis zone (34) to generate hot char. Gases (38) are withdrawn from the pyrolysis zone (34) and reinjected into the region of the reactor adjacent the gasification zone (32). This eliminates hydrocarbons in the gas by steam reformation on the hot char. The product gas (14) is withdrawn from a region of the reactor between the gasification zone (32) and the pyrolysis zone (34). The product gas will be free of tar and other hydrocarbons, and thus be suitable for use in many processes.

Effects of carbon dioxide on pyrolysis of peat

International Nuclear Information System (INIS)

Lee, Jechan; Yang, Xiao; Song, Hocheol; Ok, Yong Sik; Kwon, Eilhann E.

2017-01-01

This study focuses on the mechanistic understanding of effects of CO 2 on pyrolysis of peat. To do this, three pyrolytic products (i.e., syngas: H 2 and CO, pyrolytic oil (tar), and biochar) were characterized. Thermal cracking of volatile organic carbons (VOCs) generated from pyrolysis of peat was enhanced in the presence of CO 2 . Besides the enhanced thermal cracking of VOCs, unknown reaction between CO 2 and VOCs was also identified. Accordingly, CO 2 played a role in enhancing syngas production and in reducing tar formation in pyrolysis of peat. This study also reveals that peat-biochar produced in CO 2 exhibited a larger surface area than that produced in N 2 . The results shown in this paper would be used for various applications such as energy recovery from peat using a potent greenhouse gas (for example, CO 2 ). - Highlights: • More CO can be produced from pyrolysis of peat in CO 2 than in N 2 . • Less amount of tar produced from pyrolysis of peat in CO 2 than in N 2 . • Surface area of peat-biochar made in CO 2 is larger than that made in N 2 . • CO 2 can modify the quantity/quality of pyrolytic products from peat.

Fluorocarbon thin film with superhydrophobic property prepared by pyrolysis of hexafluoropropylene oxide

International Nuclear Information System (INIS)

Wang Jun; Song Xue; Li Rui; Shen Jinpeng; Yang Guangcheng; Huang Hui

2012-01-01

Highlights: ► We successfully prepared nanostructured fluorocarbon thin films using CVD method without any catalysts at low pyrolysis temperature (200–300 °C) of HFPO. ► The films show disparate morphology, high content of CF 2 (>90%), which are also characteristic of bulk PTFE. ► The film deposited at 300 °C shows superhydrophobic property (water contact angle of 172.7°). - Abstract: A fluorocarbon thin film with superhydrophobic property was prepared by chemical vapor deposition (CVD) method at low temperature (200–300 °C) via pyrolysis hexafluoropropylene oxide (HFPO). The experiment results indicated the morphology and structure of fluorocarbon films were strongly dependent on the pyrolysis temperature. As shown through atomic force microscope (AFM), the surface morphology of the films ranged from rodlike grains to sheets. Fourier transform infrared (FTIR) spectroscopy revealed that all the films contained the vibrational frequencies of linear CF 2 chains, which were also characteristic of bulk poly tetrafluoroethylene (PTFE). X-ray photoelectron spectroscopy (XPS) analysis showed that CF 2 structures were predominant in the films with high order. The film deposited at 300 °C exhibited a superhydrophobic surface with contact angle up to 172.7°.

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; MacPhee, J.A.; Vancea, L.; Ciavaglia, L.A.; Nandi, B.N.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500 C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by N.M.R. and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars. (19 refs.)

Effect of oxidation on the chemical nature and distribution of low-temperature pyrolysis products from bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Ciavaglia, L.A.; MacPhee, J.A.; Nandi, B.N.; Vancea, L.

1983-04-01

Two bituminous coals, a high volatile Eastern Canadian and a medium volatile Western Canadian, were used to investigate the effect of oxidation on yields and chemical composition of gases, liquids and chars produced during coal pyrolysis. Pyrolysis experiments were performed at 500/sup 0/C using the Fischer assay method. Mild oxidation of coals resulted in a decrease of liquid hydrocarbon yields. Further coal oxidation increased the proportion of aromatic carbon in liquid products as determined by n.m.r., and also increased the content of oxygen in liquid products. The content of oxygen in chars was markedly lower than in corresponding coals. An attempt is made to explain reactions occurring during oxidation and subsequent pyrolysis of coal on the basis of differences in chemical composition of gases, liquids and chars.

Novel technique for coal pyrolysis and hydrogenation product analysis

Energy Technology Data Exchange (ETDEWEB)

Pfefferle, L.D.

1992-01-01

This report covers the last quarter of the last year of the three-year grant period. In the final project year, we concentrated on the pyrolysis and oxidative pyrolysis of large hydrocarbons and mixtures of large and small hydrocarbons in order to develop the VUV-MS technique for compounds more representative of those in coal pyrolysis applications. Special focus was directed at the pyrolysis and oxidative pyrolysis of benzene and benzene acetylene mixtures. The acetylene/benzene mixtures were used to gain a better understanding of the mechanisms of molecular growth in such systems specifically to look at the kinetics of aryl-aryl reactions as opposed to small molecule addition to phenyl radicals. Sarofim and coworkers at MIT have recently demonstrated the importance of these reactions in coal processing environments. In the past, the growth mechanism for the formation of midsized PAH has been postulated to involve primarily successive acetylene additions to phenyl-type radicals, our work confmns this as an important mechanism especially for smaller PAH but also investigates conditions where biaryl formation can play an important role in higher hydrocarbon formation.

Simulating Biomass Fast Pyrolysis at the Single Particle Scale

Energy Technology Data Exchange (ETDEWEB)

Ciesielski, Peter [National Renewable Energy Laboratory (NREL); Wiggins, Gavin [ORNL; Daw, C Stuart [ORNL; Jakes, Joseph E. [U.S. Forest Service, Forest Products Laboratory, Madison, Wisconsin, USA

2017-07-01

Simulating fast pyrolysis at the scale of single particles allows for the investigation of the impacts of feedstock-specific parameters such as particle size, shape, and species of origin. For this reason particle-scale modeling has emerged as an important tool for understanding how variations in feedstock properties affect the outcomes of pyrolysis processes. The origins of feedstock properties are largely dictated by the composition and hierarchical structure of biomass, from the microstructural porosity to the external morphology of milled particles. These properties may be accounted for in simulations of fast pyrolysis by several different computational approaches depending on the level of structural and chemical complexity included in the model. The predictive utility of particle-scale simulations of fast pyrolysis can still be enhanced substantially by advancements in several areas. Most notably, considerable progress would be facilitated by the development of pyrolysis kinetic schemes that are decoupled from transport phenomena, predict product evolution from whole-biomass with increased chemical speciation, and are still tractable with present-day computational resources.

The coke formation during the pyrolysis of 1,2-dichloroethane - results of radiotracer experiments

International Nuclear Information System (INIS)

Kopinke, F.D.; Zychlinski, W.; Rodewald, D.

1990-01-01

The formation of coke-like deposits during the pyrolysis of dichloroethane has been investigated by means of 14 C-labelled compounds. Starting from industrial feedstocks coke is formed from dichloroethane and its primary reaction products as well as from trace impurities with comparable rates. Chloroprene has been revealed as an effective coke precursor. The coke formation from industrial feedstocks can be reduced significantly by suitable purification methods. (author)

Development of advanced technologies for biomass pyrolysis

Science.gov (United States)

Xu, Ran

The utilization of biomass resources as a renewable energy resource is of great importance in responding to concerns over the protection of the environment and the security of energy supply. This PhD research focuses on the investigation of the conversion of negative value biomass residues into value-added fuels through flash pyrolysis. Pyrolysis Process Study. A pilot plant bubbling fluidized bed pyrolyzer has been set up and extensively used to thermally crack various low or negative value agricultural, food and biofuel processing residues to investigate the yields and quality of the liquid [bio-oil] and solid (bio-char] products. Another novel aspect of this study is the establishment of an energy balance from which the thermal self-sustainability of the pyrolysis process can be assessed. Residues such as grape skins and mixture of grape skins and seeds, dried distiller's grains from bio-ethanol plants, sugarcane field residues (internal bagasse, external and whole plant) have been tested. The pyrolysis of each residue has been carried out at temperatures ranging from 300 to 600°C and at different vapor residence times, to determine its pyrolysis behavior including yields and the overall energy balance. The thermal sustainability of the pyrolysis process has been estimated by considering the energy contribution of the product gases and liquid bio-oll in relation to the pyrolysis heat requirements. The optimum pyrolysis conditions have been identified in terms of maximizing the liquid blo-oil yield, energy density and content of the product blo-oil, after ensuring a self-sustainable process by utilizing the product gases and part of char or bio-oil as heat sources. Adownflow pyrolyzer has also been set up. Preliminary tests have been conducted using much shorter residence times. Bio-oil Recovery. Bio-oil recovery from the pyrolysis unit includes condensation followed by demisting. A blo-oil cyclonic condensing system is designed A nearly tangential entry forces

Cheap carbon sorbents produced from lignite by catalytic pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, B.N.; Schchipko, M.L. [Inst. of Chemistry of Natural Organic Materials, Akademgorodok, Krasnoyarsk (Russian Federation)

1995-12-01

Some data are presented describing the new technology of carbon sorbent production from powdered lignite in the installation with fluidized bed of catalyst. It was shown the different types of char products with extended pore structure and high sorption ability can be produced from cheap and accessible lignite of Kansk-Achinsk coal pit in pilot installation with fluidized bed of Al-Cu-Cr oxide catalyst or catalytically active slag materials. In comparison with the conventional technologies of pyrolysis the catalytic pyrolysis allows to increase by 3-5 times the process productivity and to decrease significantly the formation of harmful compounds. The latter is accomplished by complete oxidation of gaseous pyrolysis products in the presence of catalysts and by avoiding the formation of pyrolysis tars - the source of cancerogenic compounds. The technology of cheap powdered sorbent production from lignites makes possible to obtain from lignite during the time of pyrolysis only a few seconds char products with porosity up to 0.6 cm{sup 3} /g, and specific surface area more than 400 m{sup 3} /g. Some methods of powdered chars molding into carbon materials with the different shape were proved for producing of firmness sorbents. Cheap carbon sorbents obtained by thermocatalytic pyrolysis can be successfully used in purification of different industrial pollutants as one-time sorbent or as adsorbents of long-term application with periodic regeneration.

The Study of Kinetic Properties and Analytical Pyrolysis of Coconut Shells

Directory of Open Access Journals (Sweden)

Mahir Said

2015-01-01

Full Text Available The kinetic properties of coconut shells during pyrolysis were studied to determine its reactivity in ground form. The kinetic parameters were determined by using thermogravimetric analyser. The activation energy was 122.780 kJ/mol. The pyrolysis products were analyzed using pyrolysis gas chromatography/mass spectrometry (Py-GC/MS. The effects of pyrolysis temperature on the distribution of the pyrolytic products were assessed in a temperature range between 673 K and 1073 K. The set time for pyrolysis was 2 s. Several compounds were observed; they were grouped into alkanes, acids, ethers and alcohols, esters, aldehydes and ketones, furans and pyrans, aromatic compounds, and nitrogen containing compounds. The product compositions varied with temperature in that range. The highest gas proportion was observed at high temperature while the acid proportion was observed to be highest in coconut shells, thus lowering the quality of bio-oil. It has been concluded that higher pyrolysis temperature increases the amount of pyrolysis products to a maximum value. It has been recommended to use coconut shell for production of gas, instead of production of bio-oil due to its high proportion of acetic acid.

Pyrolysis of tyre powder using microwave thermogravimetric analysis: Effect of microwave power.

Science.gov (United States)

Song, Zhanlong; Yang, Yaqing; Zhou, Long; Zhao, Xiqiang; Wang, Wenlong; Mao, Yanpeng; Ma, Chunyuan

2017-02-01

The pyrolytic characteristics of tyre powder treated under different microwave powers (300, 500, and 700 W) were studied via microwave thermogravimetric analysis. The product yields at different power levels were studied, along with comparative analysis of microwave pyrolysis and conventional pyrolysis. The feedstock underwent preheating, intense pyrolysis, and final pyrolysis in sequence. The main and secondary weight loss peaks observed during the intense pyrolysis stage were attributed to the decomposition of natural rubbers and synthetic rubbers, respectively. The total mass loss rates, bulk temperatures, and maximum temperatures were distinctively higher at higher powers. However, the maximum mass loss rate (0.005 s -1 ), the highest yields of liquid product (53%), and the minimum yields of residual solid samples (43.83%) were obtained at 500 W. Compared with conventional pyrolysis, microwave pyrolysis exhibited significantly different behaviour with faster reaction rates, which can decrease the decomposition temperatures of both natural and synthetic rubber by approximately 110 °C-140 °C.

Fast Pyrolysis of Four Lignins from Different Isolation Processes Using Py-GC/MS

Directory of Open Access Journals (Sweden)

Xiaona Lin

2015-06-01

Full Text Available Pyrolysis is a promising approach that is being investigated to convert lignin into higher value products including biofuels and phenolic chemicals. In this study, fast pyrolysis of four types of lignin, including milled Amur linden wood lignin (MWL, enzymatic hydrolysis corn stover lignin (EHL, wheat straw alkali lignin (AL and wheat straw sulfonate lignin (SL, were performed using pyrolysis gas-chromatography/mass spectrometry (Py-GC/MS. Thermogravimetric analysis (TGA showed that the four lignins exhibited widely different thermolysis behaviors. The four lignins had similar functional groups according to the FTIR analysis. Syringyl, guaiacyl and p-hydroxyphenylpropane structural units were broken down during pyrolysis. Fast pyrolysis product distributions from the four lignins depended strongly on the lignin origin and isolation process. Phenols were the most abundant pyrolysis products from MWL, EHL and AL. However, SL produced a large number of furan compounds and sulfur compounds originating from kraft pulping. The effects of pyrolysis temperature and time on the product distributions from corn stover EHL were also studied. At 350 °C, EHL pyrolysis mainly produced acids and alcohols, while phenols became the main products at higher temperature. No obvious influence of pyrolysis time was observed on EHL pyrolysis product distributions.

Thermal-maturity limit for primary thermogenic-gas generation from humic coals as determined by hydrous pyrolysis

Science.gov (United States)

Lewan, Michael; Kotarba, M.J.

2014-01-01

Hydrous-pyrolysis experiments at 360°C (680°F) for 72 h were conducted on 53 humic coals representing ranks from lignite through anthracite to determine the upper maturity limit for hydrocarbon-gas generation from their kerogen and associated bitumen (i.e., primary gas generation). These experimental conditions are below those needed for oil cracking to ensure that generated gas was not derived from the decomposition of expelled oil generated from some of the coals (i.e., secondary gas generation). Experimental results showed that generation of hydrocarbon gas ends before a vitrinite reflectance of 2.0%. This reflectance is equivalent to Rock-Eval maximum-yield temperature and hydrogen indices (HIs) of 555°C (1031°F) and 35 mg/g total organic carbon (TOC), respectively. At these maturity levels, essentially no soluble bitumen is present in the coals before or after hydrous pyrolysis. The equivalent kerogen atomic H/C ratio is 0.50 at the primary gas-generation limit and indicates that no alkyl moieties are remaining to source hydrocarbon gases. The convergence of atomic H/C ratios of type-II and -I kerogen to this same value at a reflectance of indicates that the primary gas-generation limits for humic coal and type-III kerogen also apply to oil-prone kerogen. Although gas generation from source rocks does not exceed vitrinite reflectance values greater than , trapped hydrocarbon gases can remain stable at higher reflectance values. Distinguishing trapped gas from generated gas in hydrous-pyrolysis experiments is readily determined by of the hydrocarbon gases when a -depleted water is used in the experiments. Water serves as a source of hydrogen in hydrous pyrolysis and, as a result, the use of -depleted water is reflected in the generated gases but not pre-existing trapped gases.

Bitumen pyrolysis

International Nuclear Information System (INIS)

Braehler, G.; Noll, T.

2014-01-01

In the past bitumen was a preferred matrix for the embedding of low and intermediate level radioactive waste: its geological history promised long term stability in final repositories. A great variety of waste has been embedded: technological waste, spent ion exchange resins, concrete, rubble, etc. Liquid waste like evaporator concentrates can be dried and embedded simultaneously in extruders, allowing simple processes and equipment. Unfortunately, during long term intermediate storage the bituminized waste drums proved out being not as stable as expected: a significant number turned out to be no longer acceptable for final disposal, and some of them even needed repacking to enable further intermediate storage. A method to rework such drums with bituminized radioactive waste seems to be urgently needed. Pyrolysis and pyro-hydrolysis (= pyrolysis with water steam added) have a long history for the treatment of organic waste: spent solvent (TBP), spent ion exchange resins, alpha waste (predominantly PVC), etc. Due to its low process temperature and the endothermic character, such processes offer significant safety advantages, as compared to incineration or dissolving in organic solvents. Results of lab-scale investigations and concepts for facilities are presented. (authors)

Perspectives for pyrolysis oil production and market in Scandinavia

International Nuclear Information System (INIS)

Sipilae, K.; Oasmaa, A.; Solantausta, Y.; Arpiainen, V.; Nyroenen, T.

1999-01-01

Commercial power production from biomass is mainly based on various combustion technologies, new gasification technologies being on pilot and demonstration scale in Europe. From the market viewpoint, there will be an attractive and large market volume for small and medium-scale combined heat and power production (CHP) and for liquid bioenergy products in order to meet the Kyoto challenges in Europe by the year 2010. Biomass pyrolysis technology offers a novel method of converting solid biomass to a liquid product which can easily be transported, stored and utilised for electricity production by diesel engines and gas turbines. The overall efficiency in pyrolysis oil production can be increased from 65 to 90 % (LHV) by integrating the big-oil production to a conventional boiler plant, the-system identified by VTT. A modern diesel power plant has an efficiency of 40 - 44 % with a high power-to-heat ratio. Parallel to diesel power plants, the big-oil can be used in existing heating oil boilers with minor burner modifications. The paper comprises an overview of market assessments in Scandinavia and a summary of pyrolysis oil production, stability and properties tests. The challenge of today is to understand and improve the properties of pyrolysis oils in order to reach a 12-month storage time without any changes in the homogeneity of pyrolysis oils. Reliable operation of oil-fired boilers and diesel power plants has to be demonstrated. As soon as these problems have been solved, biomass pyrolysis technologies will offer new attractive bioenergy market opportunities where a huge potential can be reached by conversing existing petroleum-fired boilers, 0.1 - 10 MW to big-oils and followed by combined heat and power production with high-efficiency diesel power plants in 0.1 - 10 MW scale. Pyrolysis technology is clearly the most attractive method for producing liquid biofuels, compared to bioalcohols and biodiesel. With the present price structure, pyrolysis oil can be

Pyrolysis of Rubber in a Screw Reactor

Science.gov (United States)

Lozhechnik, A. V.; Savchin, V. V.

2016-11-01

On the basis of an analysis of thermal methods described in the literature and from the results of experimental investigations of steam conversion, the authors have developed and created a facility for thermal processing of rubber waste. Rubber crumb was used as the raw material; the temperature in the reactor was 500°C; nitrogen, steam, and a mixture of light hydrocarbons (noncondensable part of pyrolysis products) represented the working medium. The pyrolysis yielded 36-38% of a solid fraction, 54-56% of a liquid hydrocarbon fraction, and 6-9% of noncondensable gases. Changes in the composition of the gas mixture have been determined at different stages of processing. Gas chromatography of pyrolysis gases has shown that the basic gases produced by pyrolysis are H2 and hydrocarbons C2H4, C3H6, C3H8, C4H8, C2H6, C3H6O2, and C4H10, and a small amount of H2S, CO, and CO2. Noncondensable gases will be used as a fuel to heat the reactor and to implement the process.

A Comparison of Lignin, Macroalgae, Wood and Straw Fast Pyrolysis

DEFF Research Database (Denmark)

Trinh, Ngoc Trung; Jensen, Peter Arendt; Dam-Johansen, Kim

2013-01-01

these biomasses. The fast pyrolysis of macroalgae showed a promising result with a bio-oil yield of 65 wt% dry ash free basis (daf) and 76 % energy recovery in the bio-oil while the lignin fast pyrolysis provides a bio-oil yield of 47 wt% daf and energy recovery in bio-oil of 45 %. The physiochemical properties...... of the bio-oils were characterized with respect to higher heating value (HHV), molecular mass distribution, viscosity, pH, density, thermal behaviors, elemental concentrations, phase separation and aging. The lignin and macroalgae oil properties were different compared to those of the wood and straw oils......A fast pyrolysis study on lignin and macroalgae (non-conventional biomass) and wood and straw (conventional biomass) were carried out in a pyrolysis centrifugal reactor at pyrolysis temperature of 550 ºC. The product distributions and energy recoveries were measured and compared among...

Hydrogen assisted catalytic biomass pyrolysis for green fuels

DEFF Research Database (Denmark)

Stummann, Magnus Zingler; Høj, Martin; Gabrielsen, Jostein

2017-01-01

due to coking of the catalyst is an inhibitive problem for this technology. The objective of the present work is to produce oxygen free gasoline and diesel from biomass by hydrogen assisted catalytic fast pyrolysis. Fast pyrolysis of beech wood has been performed in high-pressure hydrogen atmosphere...

Identification of Synthetic Polymers and Copolymers by Analytical Pyrolysis-Gas Chromatography/Mass Spectrometry

Science.gov (United States)

Kusch, Peter

2014-01-01

An experiment for the identification of synthetic polymers and copolymers by analytical pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS) was developed and performed in the polymer analysis courses for third-year undergraduate students of chemistry with material sciences, and for first-year postgraduate students of polymer sciences. In…

Analysis of small molecular phase in coal involved in pyrolysis and solvent extraction by PGC

Energy Technology Data Exchange (ETDEWEB)

Jie Feng; Wen-Ying Li; Ke-Chang Xie [Taiyuan University of Technology, Taiyuan (China). Key Laboratory of Coal Science and Technology

2004-06-01

The small molecular phase, which strongly affects coal's reactivity, is the main part of the structure unit in coal. At present, its composition and structure features have not been clearly understood. In this paper, a flash pyrolysis technique with on-line GC (PGC) was used to investigate the properties of the small molecular phase from six kinds of rank coal in China. Experiments were divided into two parts: one is PGC of parent coal; another is PGC of coal extracts from NMP + CS{sub 2} (75:1) solvent extraction at 373 K. Results show that the small molecular phase mainly consists of C12-C16 compounds that could be integrally released when the heating rate was greater than 10 K/ms and the final pyrolysis temperature was 1373 K; other compounds may be the products of decomposition and polymerization from this small molecular phase during pyrolysis. 13 refs., 7 figs., 1 tab.

Co pyrolysis of biomass and PP

International Nuclear Information System (INIS)

Heo, Hyeon Su; Kim, Jung Hwan; Cho, Hye Jung; Ko, Jeong Huy; Park, Hye Jin; Bae, Yoon Ju; Park, Young Kwon

2010-01-01

Full text: While bio-oil has received considerable attention both as a source of energy and as an organic feedstock, its stability as fuel is very low due to high oxygen content. Therefore, there are many efforts to upgrade it. Among them, co pyrolysis with polyolefin can be a method to obtain stable bio-oil. Because polyolefins contain higher hydrogen and carbon content than biomass and no oxygen, plastic/ biomass co pyrolysis may upgrade the bio-oil properties by increasing the carbon and hydrogen contents while reducing oxygen content. In this study, wood biomass was mixed with PP and then co pyrolysis was carried out in a batch reactor. The produced oil and gas was analyzed using GC and GC-MS. Also elemental analysis was performed to know the hydrogen, carbon and oxygen content of bio-oil. The effect of various reaction conditions on bio-oil properties were presented in detail. (author)

Oxidative desulfurization of tire pyrolysis oil

Directory of Open Access Journals (Sweden)

Ahmad Shahzad

2016-01-01

Full Text Available This paper presents a low cost method for the purification of oils obtained from the pyrolysis of used tires. Oxidative desulfurization is a promising route for purification of tire pyrolysis oils as hydro-desulfurization may not be affordable for small scale industries. Different additives and acids have been employed for the enhancement of properties of pyrolytic oils. The experimental conditions were kept identical throughout, i.e. atmospheric pressure and 50°C temperature for comparison of performance of various additives. The use of hydrogen peroxide-acetic acid mixture (10 wt.% was found more economical and effective in desulfurization and improvement of fuel properties of sample oils. The contribution of sulfuric acid in desulfurization and decreasing viscosity was also satisfactory but due to high price of concentrated sulfuric acid its use may not be economical. Calcium oxide and Fuller’s earth was not found to be effective in desulfurization. Results indicate that oxidative desulfurization could render tire pyrolysis oils suitable for blending as heating fuel.

Co-pyrolysis characteristics and kinetic analysis of organic food waste and plastic.

Science.gov (United States)

Tang, Yijing; Huang, Qunxing; Sun, Kai; Chi, Yong; Yan, Jianhua

2018-02-01

In this work, typical organic food waste (soybean protein (SP)) and typical chlorine enriched plastic waste (polyvinyl chloride (PVC)) were chosen as principal MSW components and their interaction during co-pyrolysis was investigated. Results indicate that the interaction accelerated the reaction during co-pyrolysis. The activation energies needed were 2-13% lower for the decomposition of mixture compared with linear calculation while the maximum reaction rates were 12-16% higher than calculation. In the fixed-bed experiments, interaction was observed to reduce the yield of tar by 2-69% and promote the yield of char by 13-39% compared with linear calculation. In addition, 2-6 times more heavy components and 61-93% less nitrogen-containing components were formed for tar derived from mixtures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of acid washing on pyrolysis of Cladophora socialis alga in microtubing reactor

International Nuclear Information System (INIS)

Ly, Hoang Vu; Kim, Seung-Soo; Kim, Jinsoo; Choi, Jae Hyung; Woo, Hee Chul

2015-01-01

Highlights: • Pyrolysis of macroalgae Cladophora socialis was conducted in micro tubular reactor. • Acid washing affected the pyrolysis behavior of Cladophora socialis. • Pyrolysis of raw and acid washed C. socialis produced bio-oils with different compositions. • Pyrolysis reaction pathway was from C. socialis to liquid and then to gas (C_1–C_4). - Abstract: Cladophora socialis is a unique macroalga that is widely grown in the coastal regions of Vietnam. In this work, the pyrolysis characteristics of C. socialis were evaluated using thermogravimetric analysis (TGA) and pyrolysis in a tubing reactor. Macroalgae have a high content of inorganic compounds. These compounds result in high char content during pyrolysis of the macroalgae, which degrades the quality of the product bio-oil. In order to study this effect, C. socialis was demineralized by acid washing to remove the inorganic compounds. The effect of acid washing on the pyrolysis product distribution and the selectivity of composition in pyrolysis oil was carefully investigated. The kinetic parameters and the primary reaction pathways were also determined based on experimental data using nonlinear least-squares regression assuming a first-order kinetics model.

The role of alkenes produced during hydrous pyrolysis of a shale

Energy Technology Data Exchange (ETDEWEB)

Leif, R.N.; Simoneit, B.R.T. [Oregon State Univ., Corvallis, OR (United States). College of Oceanic and Atmospheric Sciences

2000-07-01

Hydrous pyrolysis experiments conducted on Messel shale with D{sub 2}O demonstrated that a large amount of deuterium becomes incorporated into the hydrocarbons generated from the shale kerogen. In order to understand the pathway of deuterium (and protium) exchange and the role of water during hydrous pyrolysis, we conducted a series of experiments using aliphatic compounds (1,13-tetradecadiene, 1-hexadecene, eicosane and dotriacontane) as probe molecules. These compounds were pyrolyzed in D{sub 2}O, shale/D{sub 2}O, and shale/H{sub 2}O and the products analyzed by GC-MS. In the absence of powdered shale, the incorporation of deuterium from D{sub 2}O occurred only in olefinic compounds via double bond isomerization. The presence of shale accelerated deuterium incorporation into the olefins and resulted in a minor amount of deuterium incorporation in the saturated n-alkanes. The pattern of deuterium substitution of the diene closely matched the deuterium distribution observed in the n-alkanes generated from the shale kerogen in the D{sub 2}O/shale pyrolyses. The presence of the shale also resulted in reduction (hydrogenation) of olefins to saturated n-alkanes with concomitant oxidation of olefins to ketones. These results show that under hydrous pyrolysis conditions, kerogen breakdown generates n-alkanes and terminal n-alkenes by free radical hydrocarbon cracking of the aliphatic kerogen structure. The terminal n-alkenes rapidly isomerize to internal alkenes via acid-catalyzed isomerization under hydrothermal conditions, a significant pathway of deuterium (and protium) exchange between water and the hydrocarbons. These n-alkenes simultaneously undergo reduction to n-alkanes (major) or oxidation to ketones (minor) via alcohols formed by the hydration of the alkenes. (Author)

Pyrolysis responses of kevlar/epoxy composite materials on laser irradiating

Science.gov (United States)

Liu, Wei-ping; Wei, Cheng-hua; Zhou, Meng-lian; Ma, Zhi-liang; Song, Ming-ying; Wu, Li-xiong

2017-05-01

The pyrolysis responses of kevlar/epoxy composite materials are valuable to study in a case of high temperature rising rate for its widely application. Distinguishing from the Thermal Gravimetric Analysis method, an apparatus is built to research the pyrolysis responses of kevlar/epoxy composite materials irradiated by laser in order to offer a high temperature rising rate of the sample. By deploying the apparatus, a near real-time gas pressure response can be obtained. The sample mass is weighted before laser irradiating and after an experiment finished. Then, the gas products molecular weight and the sample mass loss evolution are derived. It is found that the pressure and mass of the gas products increase with the laser power if it is less than 240W, while the molecular weight varies inversely. The variation tendency is confusing while the laser power is bigger than 240W. It needs more deeper investigations to bring it to light.

Modelling solute dispersion in periodic heterogeneous porous media: Model benchmarking against intermediate scale experiments

Science.gov (United States)

Majdalani, Samer; Guinot, Vincent; Delenne, Carole; Gebran, Hicham

2018-06-01

This paper is devoted to theoretical and experimental investigations of solute dispersion in heterogeneous porous media. Dispersion in heterogenous porous media has been reported to be scale-dependent, a likely indication that the proposed dispersion models are incompletely formulated. A high quality experimental data set of breakthrough curves in periodic model heterogeneous porous media is presented. In contrast with most previously published experiments, the present experiments involve numerous replicates. This allows the statistical variability of experimental data to be accounted for. Several models are benchmarked against the data set: the Fickian-based advection-dispersion, mobile-immobile, multirate, multiple region advection dispersion models, and a newly proposed transport model based on pure advection. A salient property of the latter model is that its solutions exhibit a ballistic behaviour for small times, while tending to the Fickian behaviour for large time scales. Model performance is assessed using a novel objective function accounting for the statistical variability of the experimental data set, while putting equal emphasis on both small and large time scale behaviours. Besides being as accurate as the other models, the new purely advective model has the advantages that (i) it does not exhibit the undesirable effects associated with the usual Fickian operator (namely the infinite solute front propagation speed), and (ii) it allows dispersive transport to be simulated on every heterogeneity scale using scale-independent parameters.

Pyrolysis of Pinus pinaster in a two-stage gasifier: Influence of processing parameters and thermal cracking of tar

Energy Technology Data Exchange (ETDEWEB)

Fassinou, Wanignon Ferdinand; Toure, Siaka [Laboratoire d' Energie Solaire-UFR-S.S.M.T. Universite de Cocody, 22BP582 Abidjan 22 (Ivory Coast); Van de Steene, Laurent; Volle, Ghislaine; Girard, Philippe [CIRAD-Foret, TA 10/16, 73, avenue J.-F. Breton, 34398 Montpellier, Cedex 5 (France)

2009-01-15

A new two-stage gasifier with fixed-bed has recently been installed on CIRAD facilities in Montpellier. The pyrolysis and the gasifier units are removable. In order to characterise the pyrolysis products before their gasification, experiments were carried out, for the first time only with the pyrolysis unit and this paper deals with the results obtained. The biomass used is Pinus pinaster. The parameters investigated are: temperature, residence time and biomass flow rate. It has been found that increasing temperature and residence time improve the cracking of tars, gas production and char quality (fixed carbon rate more than 90%, volatile matter rate less than 4%). The increase of biomass flow rate leads to a bad char quality. The efficiency of tar cracking, the quality and the heating value of the charcoal and the gases, indicate that: temperature between 650 C and 750 C, residence time of 30 min, biomass flow rate between 10 and 15 kg/h should be the most convenient experimental conditions to get better results from the experimental device and from the biomass pyrolysis process. The kinetic study of charcoal generation shows that the pyrolysis process, in experimental conditions, is a first-order reaction. The kinetic parameters calculated are comparable with those found by other researchers. (author)

Acoustic and Petrophysical Evolution of Organic-Rich Chalk Following Maturation Induced by Unconfined Pyrolysis

Science.gov (United States)

Shitrit, Omri; Hatzor, Yossef H.; Feinstein, Shimon; Vinegar, Harold J.

2017-12-01

Thermal maturation is known to influence the rock physics of organic-rich rocks. While most studies were performed on low-porosity organic-rich shales, here we examine the effect of thermal maturation on a high-porosity organic-rich chalk. We compare the physical properties of native state immature rock with the properties at two pyrolysis-simulated maturity levels: early-mature and over-mature. We further evaluate the applicability of results from unconfined pyrolysis experiments to naturally matured rock properties. Special attention is dedicated to the elastic properties of the organic phase and the influence of bitumen and kerogen contents. Rock physics is studied based on confined petrophysical measurements of porosity, density and permeability, and measurements of bedding-normal acoustic velocities at estimated field stresses. Geochemical parameters like total organic carbon (TOC), bitumen content and thermal maturation indicators are used to monitor variations in density and volume fraction of each phase. We find that porosity increases significantly upon pyrolysis and that P wave velocity decreases in accordance. Solids density versus TOC relationships indicate that the kerogen increases its density from 1.43 to 1.49 g/cc at the immature and early-mature stages to 2.98 g/cc at the over-mature stage. This density value is unusually high, although increase in S wave velocity and backscatter SEM images of the over-mature samples verify that the over-mature kerogen is significantly denser and stiffer. Using the petrophysical and acoustic properties, the elastic moduli of the rock are estimated by two Hashin-Shtrikman (HS)-based models: "HS + BAM" and "HS kerogen." The "HS + BAM" model is calibrated to the post-pyrolysis measurements to describe the mechanical effect of the unconfined pyrolysis on the rock. The absence of compaction in the pyrolysis process causes the post-pyrolysis samples to be extremely porous. The "HS kerogen" model, which simulates a

Effects of feedstock and pyrolysis temperature on biochar adsorption of ammonium and nitrate.

Science.gov (United States)

Gai, Xiapu; Wang, Hongyuan; Liu, Jian; Zhai, Limei; Liu, Shen; Ren, Tianzhi; Liu, Hongbin

2014-01-01

Biochar produced by pyrolysis of biomass can be used to counter nitrogen (N) pollution. The present study investigated the effects of feedstock and temperature on characteristics of biochars and their adsorption ability for ammonium N (NH4(+)-N) and nitrate N (NO3(-)-N). Twelve biochars were produced from wheat-straw (W-BC), corn-straw (C-BC) and peanut-shell (P-BC) at pyrolysis temperatures of 400, 500, 600 and 700°C. Biochar physical and chemical properties were determined and the biochars were used for N sorption experiments. The results showed that biochar yield and contents of N, hydrogen and oxygen decreased as pyrolysis temperature increased from 400°C to 700°C, whereas contents of ash, pH and carbon increased with greater pyrolysis temperature. All biochars could sorb substantial amounts of NH4(+)-N, and the sorption characteristics were well fitted to the Freundlich isotherm model. The ability of biochars to adsorb NH4(+)-N followed: C-BC>P-BC>W-BC, and the adsorption amount decreased with higher pyrolysis temperature. The ability of C-BC to sorb NH4(+)-N was the highest because it had the largest cation exchange capacity (CEC) among all biochars (e.g., C-BC400 with a CEC of 38.3 cmol kg(-1) adsorbed 2.3 mg NH4(+)-N g(-1) in solutions with 50 mg NH4(+) L(-1)). Compared with NH4(+)-N, none of NO3(-)-N was adsorbed to biochars at different NO3(-) concentrations. Instead, some NO3(-)-N was even released from the biochar materials. We conclude that biochars can be used under conditions where NH4(+)-N (or NH3) pollution is a concern, but further research is needed in terms of applying biochars to reduce NO3(-)-N pollution.

Effects of feedstock and pyrolysis temperature on biochar adsorption of ammonium and nitrate.

Directory of Open Access Journals (Sweden)

Xiapu Gai

Full Text Available Biochar produced by pyrolysis of biomass can be used to counter nitrogen (N pollution. The present study investigated the effects of feedstock and temperature on characteristics of biochars and their adsorption ability for ammonium N (NH4(+-N and nitrate N (NO3(--N. Twelve biochars were produced from wheat-straw (W-BC, corn-straw (C-BC and peanut-shell (P-BC at pyrolysis temperatures of 400, 500, 600 and 700°C. Biochar physical and chemical properties were determined and the biochars were used for N sorption experiments. The results showed that biochar yield and contents of N, hydrogen and oxygen decreased as pyrolysis temperature increased from 400°C to 700°C, whereas contents of ash, pH and carbon increased with greater pyrolysis temperature. All biochars could sorb substantial amounts of NH4(+-N, and the sorption characteristics were well fitted to the Freundlich isotherm model. The ability of biochars to adsorb NH4(+-N followed: C-BC>P-BC>W-BC, and the adsorption amount decreased with higher pyrolysis temperature. The ability of C-BC to sorb NH4(+-N was the highest because it had the largest cation exchange capacity (CEC among all biochars (e.g., C-BC400 with a CEC of 38.3 cmol kg(-1 adsorbed 2.3 mg NH4(+-N g(-1 in solutions with 50 mg NH4(+ L(-1. Compared with NH4(+-N, none of NO3(--N was adsorbed to biochars at different NO3(- concentrations. Instead, some NO3(--N was even released from the biochar materials. We conclude that biochars can be used under conditions where NH4(+-N (or NH3 pollution is a concern, but further research is needed in terms of applying biochars to reduce NO3(--N pollution.

Production of an alternative fuel by the co-pyrolysis of landfill recovered plastic wastes and used lubrication oils.

Science.gov (United States)

Breyer, Sacha; Mekhitarian, Loucine; Rimez, Bart; Haut, B

2017-02-01

This work is a preliminary study for the development of a co-pyrolysis process of plastic wastes excavated from a landfill and used lubrication oils, with the aim to produce an alternative liquid fuel for industrial use. First, thermogravimetric experiments were carried out with pure plastics (HDPE, LDPE, PP and PS) and oils (a motor oil and a mixture of used lubrication oils) in order to highlight the interactions occurring between a plastic and an oil during their co-pyrolysis. It appears that the main decomposition event of each component takes place at higher temperatures when the components are mixed than when they are alone, possibly because the two components stabilize each other during their co-pyrolysis. These interactions depend on the nature of the plastic and the oil. In addition, co-pyrolysis experiments were led in a lab-scale reactor using a mixture of excavated plastic wastes and used lubrication oils. On the one hand, the influence of some key operating parameters on the outcome of the process was analyzed. It was possible to produce an alternative fuel for industrial use whose viscosity is lower than 1Pas at 90°C, from a plastic/oil mixture with an initial plastic mass fraction between 40% and 60%, by proceeding at a maximum temperature included in the range 350-400°C. On the other hand, the amount of energy required to successfully co-pyrolyze, in lab conditions, 1kg of plastic/oil mixture with an initial plastic mass fraction of 60% was estimated at about 8MJ. That amount of energy is largely used for the thermal cracking of the molecules. It is also shown that, per kg of mixture introduced in the lab reactor, 29MJ can be recovered from the combustion of the liquid resulting from the co-pyrolysis. Hence, this co-pyrolysis process could be economically viable, provided heat losses are addressed carefully when designing an industrial reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microwave-assisted pyrolysis of biomass for liquid biofuels production

DEFF Research Database (Denmark)

Yin, Chungen

2012-01-01

Production of 2nd-generation biofuels from biomass residues and waste feedstock is gaining great concerns worldwide. Pyrolysis, a thermochemical conversion process involving rapid heating of feedstock under oxygen-absent condition to moderate temperature and rapid quenching of intermediate products......, is an attractive way for bio-oil production. Various efforts have been made to improve pyrolysis process towards higher yield and quality of liquid biofuels and better energy efficiency. Microwave-assisted pyrolysis is one of the promising attempts, mainly due to efficient heating of feedstock by ‘‘microwave...

Suspension Combustion of Wood: Influence of Pyrolysis Conditions on Char Yield, Morphology, and Reactivity

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo; Jensen, Peter Arendt; Jensen, Anker Degn

2008-01-01

Chars from pine and beech wood were produced by fast pyrolysis in an entrained flow reactor and by slow pyrolysis in a thermogravimetric analyzer. The influence of pyrolysis temperature, heating rate and particle size on char yield and morphology was investigated. The applied pyrolysis temperature...... varied in the range 673−1673 K for slow pyrolysis and between 873 and 1573 K for fast pyrolysis. The chars were oxidized in a thermogravimetric analyzer and the mass loss data were used to determine char oxidation reactivity. Char yield from fast pyrolysis (104−105 K/s) was as low as 1 to 6% on a dry ash......, char oxidation reactivity decreased as pyrolysis temperature increased. The amount and composition of the ash forming matter of the wood fuels seems to play an important role in determining the differences in char yield, morphology and reactivity....

Pyrolysis Kinetic Modelling of Wheat Straw from the Pannonian Region

Directory of Open Access Journals (Sweden)

Ivan Pešenjanski

2016-01-01

Full Text Available The pyrolysis/devolatilization is a basic step of thermochemical processes and requires fundamental characterization. In this paper, the kinetic model of pyrolysis is specified as a one-step global reaction. This type of reaction is used to describe the thermal degradation of wheat straw samples by measuring rates of mass loss of solid matter at a linear increase in temperature. The mentioned experiments were carried out using a derivatograph in an open-air environment. The influence of different factors was investigated, such as particle size, humidity levels, and the heating rate in the kinetics of devolatilization. As the measured values of mass loss and temperature functions transform in Arrhenius coordinates, the results are shown in the form of saddle curves. Such characteristics cannot be approximated with one equation in the form of Arrhenius law. For use in numerical applications, transformed functions can be approximated by linear regression for three separate intervals. Analysis of measurement resulting in granulation and moisture content variations shows that these factors have no significant influence. Tests of heating rate variations confirm the significance of this impact, especially in warmer regions. The influence of this factor should be more precisely investigated as a general variable, which should be the topic of further experiments.

Study of mobilization and speciation of trace elements in coal pyrolysis

International Nuclear Information System (INIS)

Ting, B.T.G.

1979-01-01

Various types of coal contain high levels of a number of trace elements. Little is known of the fates of these trace elements during the conversion of coal to liquid and gaseous products. Studies were undertaken of mobilization and speciation of trace elements in coal pyrolysis, one of the major coal conversion processes. The bituminous coal was pyrolyzed to produce liquid and gaseous products. The pyrolysis products were collected in traps in an inert gas stream. In addition mildly hydrogenated coal was prepared by mixing with tetralin, a hydrogen donor solvent, at boiling temperature. In order to characterize each element specifically during pyrolysis, base samples of coal and mildly hydrogenated coal (H-coal) were spiked with heavy metal sulfides, trace metals bound to partially oxidized coal (coal humates), and halide salts prior to carrying out pyrolysis. Eight elements were investigated in this research. They are As, Br, Cl, Co, Cr, Mn, Se, and V. Pre-spiked hydrogenated coal, i.e., pulverized coal spiked with halide salts and heavy metal sulfides then hydrogenated with tetralin, was prepared and studied for the fates of these elements during pyrolysis. Chlorinated and brominated coals were also prepared to compare the volatility differences between organically and inorganically bound halogens during the pyrolysis reaction. These products and the coal char residues were analyzed for the spiked elements mainly by neutron activation analysis for the spiked elements to determine their degree of volatility. Volatility and recovery (mass balance) will be discussed for those elements that appeared highly volatile during pyrolysis. In order to understand the halogenated compounds in the pyrolysis products, gas chromatograms were taken to the collected pyrolysis products of coal, hydrogenated coal, NaCl spiked coal, NaBr spiked coal, chlorinated coal, and brominated coal

Discernment of synergism in pyrolysis of biomass blends using thermogravimetric analysis.

Science.gov (United States)

Mallick, Debarshi; Poddar, Maneesh Kumar; Mahanta, Pinakeswar; Moholkar, Vijayanand S

2018-04-12

This study reports pyrolysis kinetics of biomass blends using isoconversional methods, viz. Friedman, FWO and KAS. Blends of three biomasses, viz. saw dust, bamboo dust and rice husk, were used. Extractives and volatiles in biomass and minerals in ash had marked influence on enhancement of reaction kinetics during co-pyrolysis, as indicated by reduction in activation energy and increase in decomposition intensity. Pyrolysis kinetics of saw dust and rice husk accelerated (positive synergy), while that of bamboo dust decelerated after blending (negative synergy). Predominant reaction mechanism of all biomass blends was 3-D diffusion in lower conversion range (α ≤ 0.5), while for α ≥ 0.5 pyrolysis followed random nucleation (or nucleation and growth mechanism). Higher reaction order for pyrolysis of blends of rice husk with saw dust and bamboo dust was attributed to catalytic effect of minerals in ash. Positive ΔH and ΔG was obtained for pyrolysis of all biomass blends. Copyright © 2018 Elsevier Ltd. All rights reserved.

Catalytic fast pyrolysis of biomass impregnated with potassium phosphate in a hydrogen atmosphere for the production of phenol and activated carbon

Science.gov (United States)

Lu, Qiang; Zhang, Zhen-xi; Wang, Xin; Guo, Hao-qiang; Cui, Min-shu; Yang, Yong-ping

2018-02-01

A new technique was proposed to co-produce phenol and activated carbon (AC) from catalytic fast pyrolysis of biomass impregnated with K3PO4 in a hydrogen atmosphere, followed by activation of the pyrolytic solid residues. Lab-scale catalytic fast pyrolysis experiments were performed to quantitatively determine the pyrolytic product distribution, as well as to investigate the effects of several factors on the phenol production, including pyrolysis atmosphere, catalyst type, biomass type, catalytic pyrolysis temperature, and catalyst impregnation content. In addition, the pyrolytic solid residues were activated to prepare ACs with high specific surface areas. The results indicated that phenol could be obtained due to the synergistic effects of K3PO4 and hydrogen atmosphere, with the yield and selectivity reaching 5.3 wt% and 17.8% from catalytic fast pyrolysis of poplar wood with 8 wt% K3PO4 at 550 oC in a hydrogen atmosphere. This technique was adaptable to different woody materials for phenol production. Moreover, gas product generated from the pyrolysis process was feasible to be recycled to provide the hydrogen atmosphere, instead of extra hydrogen supply. In addition, the pyrolytic solid residue was suitable for AC preparation, using CO2 activation method, the specific surface area was as high as 1605 m2/g.

Short-Term Effect of Feedstock and Pyrolysis Temperature on Biochar Characteristics, Soil and Crop Response in Temperate Soils

DEFF Research Database (Denmark)

Nelissen, Victoria; Ruysschaert, Greet; Müller-Stöver, Dorette Sophie

2014-01-01

At present, there is limited understanding of how biochar application to soil could be beneficial to crop growth in temperate regions and which biochar types are most suitable. Biochar’s (two feedstocks: willow, pine; three pyrolysis temperatures: 450 °C, 550 °C, 650 °C) effect on nitrogen (N......) availability, N use efficiency and crop yield was studied in northwestern European soils using a combined approach of process-based and agronomic experiments. Biochar labile carbon (C) fractions were determined and a phytotoxicity test, sorption experiment, N incubation experiment and two pot trials were...... conducted. Generally, biochar caused decreased soil NO3−availability and N use efficiency, and reduced biomass yields compared to a control soil. Soil NO3−concentrations were more reduced in the willow compared to the pine biochar treatments and the reduction increased with increasing pyrolysis temperatures...

Reaction-transport simulations of non-oxidative methane conversion with continuous hydrogen removal: Homogeneous-heterogeneous methane reaction pathways

International Nuclear Information System (INIS)

Li, Lin; Borry, Richard W.; Iglesia, Enrique

2000-01-01

Detailed kinetic-transport models were used to explore thermodynamic and kinetic barriers in the non-oxidative conversion of CH4 via homogeneous and homogeneous-heterogeneous pathways and the effects of continuous hydrogen removal and of catalytic sites on attainable yields of useful C2-C10 products. The homogeneous kinetic model combines separately developed models for low-conversion pyrolysis and for chain growth to form large aromatics and carbon. The H2 formed in the reaction decreases CH4 pyrolysis rates and equilibrium conversions and it favors the formation of lighter products. The removal of H2 along tubular reactors with permeable walls increases reaction rates and equilibrium CH4 conversions. C2-C10 yields reach values greater than 90 percent at intermediate values of dimensionless transport rates (delta=1-10), defined as the ratio hydrogen transport and methane conversion rates. Homogeneous reactions require impractical residence times, even with H2 removal, because of slow initiation and chain transfer rates. The introduction of heterogeneous chain initiation pathways using surface sites that form methyl radicals eliminates the induction period without influencing the homogeneous product distribution. Methane conversion, however, occurs predominately in the chain transfer regime, within which individual transfer steps and the formation of C2 intermediates become limited by thermodynamic constraints. Catalytic sites alone cannot overcome these constraints. Catalytic membrane reactors with continuous H2 removal remove these thermodynamic obstacles and decrease the required residence time. Reaction rates become limited by homogeneous reactions of C2 products to form C6+ aromatics. Higher delta values lead to subsequent conversion of the desired C2-C10 products to larger polynuclear aromatics. We conclude that catalytic methane pyrolysis at the low temperatures required for restricted chain growth and the elimination of thermodynamics constraints via

Biotechnological Perspectives of Pyrolysis Oil for a Bio-Based Economy.

Science.gov (United States)

Arnold, Stefanie; Moss, Karin; Henkel, Marius; Hausmann, Rudolf

2017-10-01

Lignocellulosic biomass is an important feedstock for a potential future bio-based economy. Owing to its compact structure, suitable decomposition technologies will be necessary to make it accessible for biotechnological conversion. While chemical and enzymatic hydrolysis are currently established methods, a promising alternative is provided by fast pyrolysis. The main resulting product thereof, referred to as pyrolysis oil, is an energy-rich and easily transportable liquid. Many of the identified constituents of pyrolysis oil, however, have previously been reported to display adverse effects on microbial growth. In this Opinion we discuss relevant biological, biotechnological, and technological challenges that need to be addressed to establish pyrolysis oil as a reliable microbial feedstock for a bio-based economy of the future. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal analysis of charring materials based on pyrolysis interface model

Directory of Open Access Journals (Sweden)

Huang Hai-Ming

2014-01-01

Full Text Available Charring thermal protection systems have been used to protect hypersonic vehicles from high heat loads. The pyrolysis of charring materials is a complicated physical and chemical phenomenon. Based on the pyrolysis interface model, a simulating approach for charring ablation has been designed in order to obtain one dimensional transient thermal behavior of homogeneous charring materials in reentry capsules. As the numerical results indicate, the pyrolysis rate and the surface temperature under a given heat flux rise abruptly in the beginning, then reach a plateau, but the temperature at the bottom rises very slowly to prevent the structural materials from being heated seriously. Pyrolysis mechanism can play an important role in thermal protection systems subjected to serious aerodynamic heat.

Application, Deactivation, and Regeneration of Heterogeneous Catalysts in Bio-Oil Upgrading

Directory of Open Access Journals (Sweden)

Shouyun Cheng

2016-12-01

Full Text Available The massive consumption of fossil fuels and associated environmental issues are leading to an increased interest in alternative resources such as biofuels. The renewable biofuels can be upgraded from bio-oils that are derived from biomass pyrolysis. Catalytic cracking and hydrodeoxygenation (HDO are two of the most promising bio-oil upgrading processes for biofuel production. Heterogeneous catalysts are essential for upgrading bio-oil into hydrocarbon biofuel. Although advances have been achieved, the deactivation and regeneration of catalysts still remains a challenge. This review focuses on the current progress and challenges of heterogeneous catalyst application, deactivation, and regeneration. The technologies of catalysts deactivation, reduction, and regeneration for improving catalyst activity and stability are discussed. Some suggestions for future research including catalyst mechanism, catalyst development, process integration, and biomass modification for the production of hydrocarbon biofuels are provided.

Formation of Methoxybenzenes from Cellulose in the Presence of Tetramethylammonium Hydroxide by Pyrolysis

International Nuclear Information System (INIS)

Choi, Sungseen; Kim, Minchul; Kim, Yunki

2013-01-01

Pyrolysis-gas chromatography/mass spectrometry (Pyrolysis-GC/MS) has been extensively used for characterizing the structural information of various macromolecules such as humic substances, woods, and synthetic polymers. Challinor improved the technique by introducing simultaneous pyrolysis and methylation with tetramethylammonium hydroxide (TMAH). As the technique offers a number of advantages over conventional pyrolysis, it has been used widely for the characterization of a wide variety of macro-organic molecules such as polysaccharides. Thermally assisted hydrolysis and methylation of carbohydrates by TMAH has been investigated. This approach has improved the separation by methylation of acidic functional group. Several researchers have demonstrated that the role of TMAH is not only the methylation of the pyrolysis products but also assisting in bond cleavage. Because TMAH possesses a strong basicity, highly basic conditions are likely to induce a variety of reactions. Pyrolysis technique using TMAH renders polar pyrolysis products volatile enough to be eluted from the GC column by subsequent online methylation

Pyrolysis oil from carbonaceous solid wastes in Malaysia

International Nuclear Information System (INIS)

Islam, M.N.; Jamil, M.K.; Ani, F.N.; Zailani, R.

2000-01-01

The agro-industrial sector of Malaysia produces a huge amount of oil palm and paddy rice. These generate a significant amount of renewable biomass solid wastes in the forms of oil palm shell and rice husk. Apart from this a huge quantity of scrap tyre is generated from the country's faster increasing usage of transportation vehicles like motorcycle, car, bus and lorries. These wastes are producing pollution and disposal problems affecting the environment. Besides energy is not recovered efficiently from these waste resources. From the elemental composition and thermogravimetric analysis (TGA) studies of the wastes, it appeared that the wastes could be used for pyrolysis liquid oil production. Pyrolysis at present is deemed to be a potential method for the conversion of carbonaceous solid wastes into upgraded liquid products which can either be tried for liquid fuel or value-added chemical. A fluidized bed bench scale fast pyrolysis system was employed for this thermochemical conversion process of solid wastes. Silica sand was used as fluidized bed material and nitrogen gas as the fluidising medium. The products obtained were liquid oil, solid char and gas. The liquid oil and solid char were collected separately while the gas was flared. The maximum liquid product yield was found to vary with feedstock material fluidized bed temperature. The maximum liquid product yield was found to be 58, 53 and 40 wt. % of biomass fed at fluidized bed temperature at 500, 525 and 450 0 C respectively for oil palm shell, scrap tyre and rice husk. The solid char yield was 25, 36 and 53 wt. % of biomass fed at the condition of maximum liquid product yield for oil palm shell, scrap tyre and rice husk respectively. The oil products were subjected to FTIR, GC and GC/MS analysis for their group composition and detailed chemical compositions. The pyrolysis oil from scrap tyre was found to contain highest percentage of pure hydrocarbons (25 wt. % of total feed) with esters and oxygenated

Catalytic flash pyrolysis of oil-impregnated-wood and jatropha cake using sodium based catalysts

NARCIS (Netherlands)

Ali Imran, A.; Bramer, Eduard A.; Seshan, Kulathuiyer; Brem, Gerrit

2016-01-01

Catalytic pyrolysis of wood with impregnated vegetable oil was investigated and compared with catalytic pyrolysis of jatropha cake making use of sodium based catalysts to produce a high quality bio-oil. The catalytic pyrolysis was carried out in two modes: in-situ catalytic pyrolysis and post

A novel integrated process of coal pyrolysis and methane CO{sub 2} reforming

Energy Technology Data Exchange (ETDEWEB)

Jing Wang; Pengfei Wang; Lijun Jin; Haoquan Hu [Dalian University of Technology, Dalian (China)

2007-07-01

In the paper, a novel pyrolysis method, namely coal pyrolysis coupling with CO{sub 2} reforming of methane (CRMP) or catalytic pyrolysis of coal coupling with CO{sub 2} reforming of methane (CRMCP), for improving the tar yield of coal pyrolysis was introduced. The behaviours of YM coal in both processes were investigated and compared with pyrolysis under N{sub 2} and H{sub 2}. The results show that the tar yield of coal pyrolysis in both processes obviously increase compared with that in N{sub 2} or H{sub 2}. When YM coal pyrolysis was carried out in stream of mixture gas CH{sub 4}/CO{sub 2} (1:1) with the existence of the catalyst at 0.1 MPa and 800{sup o}C, the tar yield is 2.8 times for CRMP and 4.3 times for CRMCP as that of pyrolysis under N{sub 2} and 1.7 and 2.6 times as that of hydropyrolysis at the same conditions, respectively. Sulfur content of char obtained from CRMP and CRMCP process are lower, especially in CRMP process, than that from N{sub 2} or H{sub 2}. 16 refs., 4 figs., 1 tab.

An economic analysis of mobile pyrolysis for northern New Mexico forests.

Energy Technology Data Exchange (ETDEWEB)

Brady, Patrick D.; Brown, Alexander L.; Mowry, Curtis Dale; Borek, Theodore Thaddeus, III

2011-12-01

In the interest of providing an economically sensible use for the copious small-diameter wood in Northern New Mexico, an economic study is performed focused on mobile pyrolysis. Mobile pyrolysis was selected for the study because transportation costs limit the viability of a dedicated pyrolysis plant, and the relative simplicity of pyrolysis compared to other technology solutions lends itself to mobile reactor design. A bench-scale pyrolysis system was used to study the wood pyrolysis process and to obtain performance data that was otherwise unavailable under conditions theorized to be optimal given the regional problem. Pyrolysis can convert wood to three main products: fixed gases, liquid pyrolysis oil and char. The fixed gases are useful as low-quality fuel, and may have sufficient chemical energy to power a mobile system, eliminating the need for an external power source. The majority of the energy content of the pyrolysis gas is associated with carbon monoxide, followed by light hydrocarbons. The liquids are well characterized in the historical literature, and have slightly lower heating values comparable to the feedstock. They consist of water and a mix of hundreds of hydrocarbons, and are acidic. They are also unstable, increasing in viscosity with time stored. Up to 60% of the biomass in bench-scale testing was converted to liquids. Lower ({approx}550 C) furnace temperatures are preferred because of the decreased propensity for deposits and the high liquid yields. A mobile pyrolysis system would be designed with low maintenance requirements, should be able to access wilderness areas, and should not require more than one or two people to operate the system. The techno-economic analysis assesses fixed and variable costs. It suggests that the economy of scale is an important factor, as higher throughput directly leads to improved system economic viability. Labor and capital equipment are the driving factors in the viability of the system. The break

The effect of pyrolysis temperature of palm oil shell on quantity and quality of liquid smoke

International Nuclear Information System (INIS)

Ratnawati; Singgih Hartanto

2010-01-01

Palm oil shell can be processed into carbon and liquid smoke through pyrolysis reaction where liquid smoke was obtained by condensation of smoke produced. In this research, liquid smoke was produced by pyrolysis of 5 kg palm oil shell at temperature of 200 °C, 300 °C, and 400 °C for 4 hours and the composition of liquid smoke was analyzed with Gas Chromatography -Mass Spectrometry (GC-MS). The pyrolysis processes at 200°C, 300 °C, and 400 °C produced 460 mL, 510 mL, and 550 mL of liquid smoke and 3.98, 3.24 and 1.49 kg of carbon respectively. The result of liquid smoke with pyrolysis process at 200 °C were 30.73 %(w/w) of antioxidant and food flavor component (guaiacol, 2,3 - butanedione, furfural and 2-methyl-2-cyclopentanone), and 34.31 %(w/w) of harmful components (phenol , 2-propanone, 2-butanone and cyclopentanone). At 400 °C, 27.39 %(w/w) of components can be used in food products and 26.51 %(w/w) of components was harmful for health. Liquid smoke produced from this experiment cannot yet be used as food preservative because it still contains harmful components which are dangerous for health, therefore it needs further separation. (author)

Microwave pyrolysis using self-generated pyrolysis gas as activating agent: An innovative single-step approach to convert waste palm shell into activated carbon

Science.gov (United States)

Yek, Peter Nai Yuh; Keey Liew, Rock; Shahril Osman, Mohammad; Chung Wong, Chee; Lam, Su Shiung

2017-11-01

Waste palm shell (WPS) is a biomass residue largely available from palm oil industries. An innovative microwave pyrolysis method was developed to produce biochar from WPS while the pyrolysis gas generated as another product is simultaneously used as activating agent to transform the biochar into waste palm shell activated carbon (WPSAC), thus allowing carbonization and activation to be performed simultaneously in a single-step approach. The pyrolysis method was investigated over a range of process temperature and feedstock amount with emphasis on the yield and composition of the WPSAC obtained. The WPSAC was tested as dye adsorbent in removing methylene blue. This pyrolysis approach provided a fast heating rate (37.5°/min) and short process time (20 min) in transforming WPS into WPSAC, recording a product yield of 40 wt%. The WPSAC was detected with high BET surface area (≥ 1200 m2/g), low ash content (< 5 wt%), and high pore volume (≥ 0.54 cm3/g), thus recording high adsorption efficiency of 440 mg of dye/g. The desirable process features (fast heating rate, short process time) and the recovery of WPSAC suggest the exceptional promise of the single-step microwave pyrolysis approach to produce high-grade WPSAC from WPS.

Pyrolysis of forestry biomass by-products in Greece

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A. [Aristotle Univ. of Thessaloniki (Greece). Dept. of Chemical Engineering

1999-06-01

This article summarizes the technical characteristics of a biomass pyrolysis pilot plant recently constructed in central Greece. It highlights the considerations involved in achieving successful pyrolysis technology and environmental and developmental goals, by reviewing technical and nontechnical barriers associated with biomass treatment technology in Greece. Data from the start-up phase of the plant operation are presented and some aspects of the process are outlined. The capacity of the plant is 1200--1450 kg/hr, based on wet biomass (Arbutus Unedo) and the pyrolysis temperature is approximately 400 C. Char yield is 14--18% weight on dry basis and is of good quality consisting of 76% C with heat content 6760 kcal/kg. Bio-oil includes 64% C and its heat content is 6250 kcal/kg.

Pyrolysis Characteristics and Kinetics of Phoenix Tree Residues as a Potential Energy

Directory of Open Access Journals (Sweden)

H. Li

2015-09-01

Full Text Available By using a thermogravimetric analyser under argon atmosphere, the pyrolysis process and the kinetic model of phoenix tree residues (the little stem, middle stem, and leaf at a 30 °C min−1 heating rate and the phoenix tree mix at three different heating rates (10 °C min−1, 30 °C min−1, and 50 °C min−1 were examined. The catalyst and the co-pyrolysis samples were at a 30 °C min−1 heating rate. The catalysts were Na2CO3, ZnCl2 and CaO in a mass fraction of 5 %. The experimental results revealed that the phoenix tree residues pyrolysis process consisted of three stages: dehydration stage, main pyrolysis stage, and the slow decomposition of residues. As the heating rate increased, the pyrolysis characteristic temperature of the phoenix tree grew, there was a backward-shift of the pyrolysis rate curve, and the mass loss rate gradually increased. The phoenix tree residues’ activation energy changed throughout the whole pyrolysis process, and the pyrolysis temperature ranges of the three main components (cellulose, hemicellulose, and lignin existed in overlapping phenomenon. As compared to the little stem, middle stem, and leaf, the phoenix tree mix was more likely to be pyrolysed under the same heating rate. Different catalysts had a different impact on the pyrolysis: ZnCl2 moved the start point of the reaction to the lower temperatures, but did not speed up the reaction; Na2CO3 speeded up the reaction without changing the start point of the reaction; CaO speeded up the reaction, moved the start point of the reaction to higher temperatures.

Pyrolysis and hydropyrolysis performance of Shendong and Pingshuo coal

Energy Technology Data Exchange (ETDEWEB)

Shiping Huang; Bo Wu; Yunpeng Zhao; Lijun Jin; Haoquan Hu [Dalian University of Technology, Dalian (China). Institute of Coal Chemical Engineering

2007-07-01

Pyrolysis and hydropyrolysis of Shendong (SD) and Pingshuo (PS) coal were performed from 500 to 700{sup o}C in a fixed-bed reactor and the product distribution and gas evolution of both processes were analyzed. The results show that, the tar yields of both PS coal and SD coal reach the highest value, about 17 wt% and 13 wt% respectively at temperature 650{sup o}C for pyrolysis. However, the tar yields of PS coal get to the highest value, about 20 wt% at temperature 650{sup o}C, and the tar yields of SD coal are improving with temperature increasing, about 12 wt% at temperature 700{sup o}C for hydropyrolysis. The tar yields of PS coal are higher than those of SD coal at the same conditions for both pyrolysis and hydropyrolysis. The total gas yield of PS coal is higher than that of SD coal for pyrolysis, but lower for hydropyrolysis.

Fast pyrolysis of lignin, macroalgae and sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Trinh, N.T.

2013-04-15

Non-conventional biomass feedstock may also be applicable for fast pyrolysis processes. Among the forms of non-conventional biomasses, macroalgae, lignin (industrial residue) and sewage sludge may be attractive materials due to their low price, non-competitiveness with food crops and the possible utilization of solid wastes. Besides, a fast pyrolysis process can be used as a process to densify the biomass and produce bioslurry, a mixture of bio-oil and pyrolytic char. The bioslurry is found to be a possible feedstock for pressurized gasification plants. Thus, the aims of this project are to investigate fast pyrolysis properties of lignin, sewage sludge and macroalgae on a lab scale PCR and characterize their bio-oil properties. Bioslurry properties with respect to use as a feedstock for pressurized gasification is also investigated. Lignin and sewage sludge PCR pyrolysis provided bio-oil yields of 47 and 54 wt% daf, and oil energy recovery of 45 and 50 %, respectively. While the macroalgae PCR pyrolysis showed promising results with an organic oil yield of 65 wt% daf and an oil energy recovery of 76 %. The HHV of the lignin, sewage sludge and macroalgae oils were 29.7, 25.7 and 25.5 MJ/kg db respectively, and that are higher than that of typical bioiv oil from conventional biomasses (23-24 MJ/kg db). Almost all metals feedstock contents were contained in the chars at temperatures of 550 - 575 deg. C for lignin, sewage sludge and macroalgae PCR pyrolysis. Due to high feedstock nitrogen and sulfur contents, also a high level of nitrogen and sulfur of macroalgae and sewage sludge oils were observed compared to conventional bio-oil and this may limit their further industrial applications. The lignin char had a high proportion of small size particles, a HHV of 21 MJ/kg db and were almost free of chloride and sulfur, thus it is considered as a promising fuel for gasification or combustion; whereas macroalgae and sewage sludge chars containing high amounts of

Economics of pyrolysis-based energy production and biochar utilization: A case study in Taiwan

International Nuclear Information System (INIS)

Kung, Chih-Chun; McCarl, Bruce A.; Cao, Xiaoyong

2013-01-01

Pyrolysis is an alternative form of renewable energy production and a potential source of greenhouse gas emissions mitigation. This study examines how poplar-based biochar can be applied in Taiwan for electricity generation and for soil improvement and to what extent it brings economic and environmental benefits. It is a preliminary study and focuses on the balances of different economic and environmental items. This paper reports on a case study examination of the economic and greenhouse gas implications of pyrolysis plus biochar utilization. The case study involves using poplar grown on set-aside land in Taiwan with the biochar applied to rice fields. We examine both fast and slow forms of pyrolysis and find how the profitability varies under different price structures. The results show that fast pyrolysis is more profitable than slow pyrolysis under current electricity price, GHG price and crop yield as the slow pyrolysis generates relatively less electricity but lower value product—biochar. We also find that fast pyrolysis and slow pyrolysis offset about 1.4 t and 1.57 t of CO 2 equivalent per ton of raw material, respectively. - Highlights: • Profitability varies due to sales revenue from electricity generation. • Neither fast pyrolysis nor slow pyrolysis is profitable under current electricity price. • Both systems offset about 1.4 t to 1.57 t of CO 2 equivalent per ton of raw material

EFFECT OF AQUEOUS PRETREATMENT ON PYROLYSIS CHARACTERISTICS OF NAPIER GRASS

Directory of Open Access Journals (Sweden)

ISAH YAKUB MOHAMMED

2015-11-01

Full Text Available Effect of non-catalytic aqueous pretretment on pyrolysis characteristics of Napier grass was investigated using thermogravimetric analyser. Increasing pretreatment severity (0.0-2.0 improved pyrolysis process. The residual mass at the end of pyrolysis for the pretreated sample was about 50% less compared to the untreated sample. Kinetics of the process was evaluated using order based model and both pretreated and untreated samples followed first order reaction. The activation energy of the pretreated samples was similar and higher than that of the raw sample which was attributed to faster rate of decomposition due removal of hetromaterials (ash, extractives and some hemicellulose in the pretreatment stage. Finally, this pretreatment method has demonstrated effectiveness for the removal of pyrolysis retardants and will improve the quantity and quality of bio-oil yield.

Fixed-bed hydrogen pyrolysis of rapeseed: product yields and compositions

International Nuclear Information System (INIS)

Onay, O.; Kockar, O.M.; Gaines, A.F.; Snape, C.E.

2006-01-01

The fixed-bed hydro pyrolysis tests have been conducted on a sample of rapeseed to investigate the effect of hydro pyrolysis on the yields and chemical structures of bio-oils, with a view to improving overall product quality. A ammonium dioxydithiomolybdenate catalyst has been used in some tests to further increase conversion. The maximum bio-oil yield of 84% was obtained in hydrogen atmosphere (with catalyst) at hydrogen pressure of 15 MPa, hydrogen flow rate of 10 dm 3 min -1 , hydro pyrolysis temperature of 520 degree C, and heating rate of 5 o Cmin -1 . Then this bio-oil was characterized by elemental analysis and some spectroscopic and chromatographic techniques. And finally, this bio-oil yield and chemical composition compared with oil obtained from fast pyrolysis condition

High temperature SU-8 pyrolysis for fabrication of carbon electrodes

DEFF Research Database (Denmark)

Hassan, Yasmin Mohamed; Caviglia, Claudia; Hemanth, Suhith

2017-01-01

In this work, we present the investigation of the pyrolysis parameters at high temperature (1100 °C) for the fabrication of two-dimensional pyrolytic carbon electrodes. The electrodes were fabricated by pyrolysis of lithographically patterned negative epoxy based photoresist SU-8. A central...... composite experimental design was used to identify the influence of dwell time at the highest pyrolysis temperature and heating rate on electrical, electrochemical and structural properties of the pyrolytic carbon: Van der Pauw sheet resistance measurements, cyclic voltammetry, electrochemical impedance...... spectroscopy and Raman spectroscopy were used to characterize the pyrolytic carbon. The results show that the temperature increase from 900 °C to 1100 °C improves the electrical and electrochemical properties. At 1100 °C, longer dwell time leads to lower resistivity, while the variation of the pyrolysis...

Heterogeneous computation tests of both substitution and reactivity worth experiments in the RB-3 reactor

International Nuclear Information System (INIS)

Broccoli, U.; Cambi, G.; Vanossi, A.; Zapellini, G.

1977-01-01

This report presents the results of several experiments carried out in the D 2 O-moderated RB-3 reactors at the CNEN's Laboratory of Montecuccolino, Bologna. The experiments referred to are either fuel-element substitution experiments or interstitial absorber experiments and were performed during the period 1972-1974. The results of measurements are compared with those obtained by means of computational procedure based on some ''cell'' codes coupled with heterogeneous codes. (authors)

Chemistry of decomposition of freshwater wetland sedimentary organic material during ramped pyrolysis

Science.gov (United States)

Williams, E. K.; Rosenheim, B. E.

2011-12-01

Ramped pyrolysis methodology, such as that used in the programmed-temperature pyrolysis/combustion system (PTP/CS), improves radiocarbon analysis of geologic materials devoid of authigenic carbonate compounds and with low concentrations of extractable authochthonous organic molecules. The approach has improved sediment chronology in organic-rich sediments proximal to Antarctic ice shelves (Rosenheim et al., 2008) and constrained the carbon sequestration potential of suspended sediments in the lower Mississippi River (Roe et al., in review). Although ramped pyrolysis allows for separation of sedimentary organic material based upon relative reactivity, chemical information (i.e. chemical composition of pyrolysis products) is lost during the in-line combustion of pyrolysis products. A first order approximation of ramped pyrolysis/combustion system CO2 evolution, employing a simple Gaussian decomposition routine, has been useful (Rosenheim et al., 2008), but improvements may be possible. First, without prior compound-specific extractions, the molecular composition of sedimentary organic matter is unknown and/or unidentifiable. Second, even if determined as constituents of sedimentary organic material, many organic compounds have unknown or variable decomposition temperatures. Third, mixtures of organic compounds may result in significant chemistry within the pyrolysis reactor, prior to introduction of oxygen along the flow path. Gaussian decomposition of the reaction rate may be too simple to fully explain the combination of these factors. To relate both the radiocarbon age over different temperature intervals and the pyrolysis reaction thermograph (temperature (°C) vs. CO2 evolved (μmol)) obtained from PTP/CS to chemical composition of sedimentary organic material, we present a modeling framework developed based upon the ramped pyrolysis decomposition of simple mixtures of organic compounds (i.e. cellulose, lignin, plant fatty acids, etc.) often found in sedimentary

Modelling heterogeneous ice nucleation on mineral dust and soot with parameterizations based on laboratory experiments

Science.gov (United States)

Hoose, C.; Hande, L. B.; Mohler, O.; Niemand, M.; Paukert, M.; Reichardt, I.; Ullrich, R.

2016-12-01

Between 0 and -37°C, ice formation in clouds is triggered by aerosol particles acting as heterogeneous ice nuclei. At lower temperatures, heterogeneous ice nucleation on aerosols can occur at lower supersaturations than homogeneous freezing of solutes. In laboratory experiments, the ability of different aerosol species (e.g. desert dusts, soot, biological particles) has been studied in detail and quantified via various theoretical or empirical parameterization approaches. For experiments in the AIDA cloud chamber, we have quantified the ice nucleation efficiency via a temperature- and supersaturation dependent ice nucleation active site density. Here we present a new empirical parameterization scheme for immersion and deposition ice nucleation on desert dust and soot based on these experimental data. The application of this parameterization to the simulation of cirrus clouds, deep convective clouds and orographic clouds will be shown, including the extension of the scheme to the treatment of freezing of rain drops. The results are compared to other heterogeneous ice nucleation schemes. Furthermore, an aerosol-dependent parameterization of contact ice nucleation is presented.

Pyrolysis oil production, properties, and utilization; Pyrolyysioeljyn valmistus, ominaisuudet ja kaeyttoe

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K.; Oasmaa, A.; Arpiainen, V.; Kuoppala, E.; Leppaemaeki, E.; Solantausta, Y.; Levander, J. VTT Energia

1995-12-31

The main tasks for 1995 were: design and assembling of experimental reactors, and physical and chemical characterisation of pyrolysis oils. A PDU-unit (20 kg/h) has been designed and it will be assembled in April 1996. A 1 kg/h pyrolyzer has been constructed with a hot-filtration system (a ceramic candle filter) and direct quenching with a hydrocarbon oil. The equipment has worked well. Pine saw dust has been used as a feed and a good-quality solids-free product oil has been obtained. In addition to this, a smaller (150 g/h) pyrolyzer has been bought from Canada (University of Waterloo). The small equipment will be used for example for catalytic upgrading of pyrolysis vapours. Chemical characterisation of pyrolysis oil has been carried out 1995. Water extraction has been developed for a fractionation method. Pyrolysis oil samples produced from mixed hardwood, eucalyptus and straw have been employed. The objective of the study has been to develop a simple characterisation method for comparison of different pyrolysis oils. For example reactive compounds have been identified. Main analytical method for analysing the water-soluble fraction has been GC-MS. The research will be continued 1996. A literature review of chemical and physical characterization of pyrolysis oils has been published 1995. Testing of fuel oil analyses has been continued within the IEA pyrolysis project. VTT Energy is responsible for fuel oil analytical methods

Pyrolysis oil production, properties, and utilization; Pyrolyysioeljyn valmistus, ominaisuudet ja kaeyttoe

Energy Technology Data Exchange (ETDEWEB)

Sipilae, K; Oasmaa, A; Arpiainen, V; Kuoppala, E; Leppaemaeki, E; Solantausta, Y; Levander, J. VTT Energia

1996-12-31

The main tasks for 1995 were: design and assembling of experimental reactors, and physical and chemical characterisation of pyrolysis oils. A PDU-unit (20 kg/h) has been designed and it will be assembled in April 1996. A 1 kg/h pyrolyzer has been constructed with a hot-filtration system (a ceramic candle filter) and direct quenching with a hydrocarbon oil. The equipment has worked well. Pine saw dust has been used as a feed and a good-quality solids-free product oil has been obtained. In addition to this, a smaller (150 g/h) pyrolyzer has been bought from Canada (University of Waterloo). The small equipment will be used for example for catalytic upgrading of pyrolysis vapours. Chemical characterisation of pyrolysis oil has been carried out 1995. Water extraction has been developed for a fractionation method. Pyrolysis oil samples produced from mixed hardwood, eucalyptus and straw have been employed. The objective of the study has been to develop a simple characterisation method for comparison of different pyrolysis oils. For example reactive compounds have been identified. Main analytical method for analysing the water-soluble fraction has been GC-MS. The research will be continued 1996. A literature review of chemical and physical characterization of pyrolysis oils has been published 1995. Testing of fuel oil analyses has been continued within the IEA pyrolysis project. VTT Energy is responsible for fuel oil analytical methods

Behenic acid pyrolysis to produce diesel-like hydrocarbons

International Nuclear Information System (INIS)

Xu, Zhi-Xiang; Liu, Peng; Xu, Gui-Sheng; He, Zhi-Xia; Ji, Heng-Song; Wang, Qian

2017-01-01

Highlights: • Behenic acid is a suitable bio-renewable resource to produce bio-fuel oil using catalytic cracking. • Little fraction of aromatic compounds presented in bio-fuel oil. • Carbon chain of fatty acid was cracked to form short carbon chain carboxyl firstly. • ESI FT-ICR MS experiment was an effective method to analyze bio-fuel oil heavy compounds. - Abstract: In order to obtain diesel-like bio-fuel oil, behenic acid was selected to carry out fast pyrolysis. The decomposition temperature of behenic acid was in the range of 250–450 °C at 20 k/min according to TG experiment. The bio-fuel oil mainly contained alkane, alkene and fatty acid. Components of products were C_1_3–C_2_0 hydrocarbon. Little fraction of aromatic compounds was found in bio-fuel oil. According to ESI FT-ICR MS analysis results, the oxygen containing compounds in bio-fuel oil were mainly O_2–O_4 classes, with the O_3 being the major class. According to GC–MS and ESI FT-ICR MS results, it was found that the carbon chain of behenic acid was cracked to form short carbon chain carboxyl firstly. And then decarboxylation reaction carried out. In other means carboxyl groups were more stable than carbon chain of fatty acid. The probable mechanism of O_4 species was free radical reaction. The recommended pyrolysis path was also proposed. Diesel-like bio-fuel oil can be obtained using behenic acid catalytic cracking.

Spray pyrolysis process for preparing superconductive films

International Nuclear Information System (INIS)

Hsu, H.M.; Yee, I.Y.

1991-01-01

This paper describes a spray pyrolysis method for preparing thin superconductive film. It comprises: preparing a spray pyrolysis solution comprising Bi,Sr,Ca and Cu metals in a solvent; heating a substrate to a first temperature; spraying the solution onto the heated substrate to form a film thereon; heating the film and substrate to a second temperature of about 700 degrees-825 degrees C, the second temperature being higher than the first temperature; heating the film and substrate to a third temperature of about 870 degrees-890 degrees C to melt the film; once the film and substrate reach the third temperature, further heat treating the film and substrate; cooling the film and substrate to ambient temperature. This patent also describes a spray pyrolysis method for preparing thin superconductive films. It comprises: preparing a spray pyrolysis solution comprising Bi, Ca and Cu metals and fluxing agent in a solvent; heating a substrate to a first temperature; spraying the solution onto the heated substrate to form a film thereon; heating the film and substrate to a second temperature about 700 degrees-825 degrees C, the second temperature being higher than the first temperature; heating the film and substrate at a third temperature about 840 degrees-860 degrees C; and cooling the film and substrate to ambient temperature

Co-pyrolysis of coal with organic solids

Energy Technology Data Exchange (ETDEWEB)

Straka, P.; Buchtele, J. [Inst. of Rock Structure and Mechanics, Prague (Czechoslovakia)

1995-12-01

The co-pyrolysis of high volatile A bituminous coal with solid organic materials (proteins, cellulose, polyisoprene, polystyrene, polyethylene-glycolterephtalate-PEGT) at a high temperature conditions was investigated. Aim of the work was to evaluate, firstly, the changes of the texture and of the porous system of solid phase after high temperature treatment in presence of different types of macromolecular solids, secondly, properties and composition of the tar and gas. Considered organic solids are important waste components. During their co-pyrolysis the high volatile bituminous coal acts as a hydrogen donor in the temperature rank 220-480{degrees}C. In the rank 500- 1000{degrees}C the solid phase is formed. The co-pyrolysis was carried out at heating rate 3 K/min. It was found that an amount of organic solid (5-10%) affects important changes in the optical texture forms of solid phase, in the pore distribution and in the internal surface area. Transport large pores volume decreases in presence of PEGT, polystyrene and cellulose and increases in presence of proteins and polyisoprene. (image analysis measurements show that the tendency of coal to create coarse pores during co-pyrolysis is very strong and increases with increasing amount of organic solid in blend). An addition of considered materials changes the sorption ability (methylene blue test, iodine adsorption test), moreover, the reactivity of the solid phase.

Processing of maize plants by rotary kiln pyrolysis; Veredlung von Maispflanzen durch Pyrolyse im Drehrohrreaktor

Energy Technology Data Exchange (ETDEWEB)

Klose, W; Wiest, W [Kassel Univ. (Gesamthochschule) (Germany). Inst. fuer Thermische Energietechnik

1997-12-31

The fuel quality of maize plants is to be characterized by short, elementary and thermonalysis. The plants will be pyrolyzed in order to facilitate transport and storage. The formal kinetic parameters of three parallel reactions describing solid matter decomposition are defined by means of TG-DSC, and the reaction enthalpy is measured. Pyrolysis experiments in a rotary kiln converter in the kg range show a strong dependence of the product spectrum on process temperature. In particular, the pyrolysis gas yield increases with temperature at the expense of pyrolysis oil and water. (orig) [Deutsch] Zur energetischen Nutzung von Kulturpflanzen wird die brennstofftechnische Charakterisierung von Maispflanzen durch Kurz-, Elementar- und Thermoanalyse durchgefuehrt. Zur Reduzierung des Aufwands fuer Transport und Lagerung sollen die Pflanzen pyrolysiert weren. Mit Hilfe der TG-DSC werden formalkinetische Parameter von drei Parallelreaktionen zur Beschreibung der Feststoffzersetzung bestimmt und die Reaktionsenthalpie gemessen. Pyrolyseversuche in einem Drehrohrreaktor im Kilogramm-Massstab ergeben eine starke Abhaengigkeit des Produktspektrums von der Prozesstemperatur. Insbesondere steigt die Pyrolysegasausbeute auf Kosten der Bildung von Pyrolyseoel und Wasser mit der Temperatur stark an. (orig)

Processing of maize plants by rotary kiln pyrolysis; Veredlung von Maispflanzen durch Pyrolyse im Drehrohrreaktor

Energy Technology Data Exchange (ETDEWEB)

Klose, W.; Wiest, W. [Kassel Univ. (Gesamthochschule) (Germany). Inst. fuer Thermische Energietechnik

1996-12-31

The fuel quality of maize plants is to be characterized by short, elementary and thermonalysis. The plants will be pyrolyzed in order to facilitate transport and storage. The formal kinetic parameters of three parallel reactions describing solid matter decomposition are defined by means of TG-DSC, and the reaction enthalpy is measured. Pyrolysis experiments in a rotary kiln converter in the kg range show a strong dependence of the product spectrum on process temperature. In particular, the pyrolysis gas yield increases with temperature at the expense of pyrolysis oil and water. (orig) [Deutsch] Zur energetischen Nutzung von Kulturpflanzen wird die brennstofftechnische Charakterisierung von Maispflanzen durch Kurz-, Elementar- und Thermoanalyse durchgefuehrt. Zur Reduzierung des Aufwands fuer Transport und Lagerung sollen die Pflanzen pyrolysiert weren. Mit Hilfe der TG-DSC werden formalkinetische Parameter von drei Parallelreaktionen zur Beschreibung der Feststoffzersetzung bestimmt und die Reaktionsenthalpie gemessen. Pyrolyseversuche in einem Drehrohrreaktor im Kilogramm-Massstab ergeben eine starke Abhaengigkeit des Produktspektrums von der Prozesstemperatur. Insbesondere steigt die Pyrolysegasausbeute auf Kosten der Bildung von Pyrolyseoel und Wasser mit der Temperatur stark an. (orig)

Method for Hot Real-Time Sampling of Pyrolysis Vapors

Energy Technology Data Exchange (ETDEWEB)

Pomeroy, Marc D [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-29

Biomass Pyrolysis has been an increasing topic of research, in particular as a replacement for crude oil. This process utilizes moderate temperatures to thermally deconstruct the biomass which is then condensed into a mixture of liquid oxygenates to be used as fuel precursors. Pyrolysis oils contain more than 400 compounds, up to 60 percent of which do not re-volatilize for subsequent chemical analysis. Vapor chemical composition is also complicated as additional condensation reactions occur during the condensation and collection of the product. Due to the complexity of the pyrolysis oil, and a desire to catalytically upgrade the vapor composition before condensation, online real-time analytical techniques such as Molecular Beam Mass Spectrometry (MBMS) are of great use. However, in order to properly sample hot pyrolysis vapors, many challenges must be overcome. Sampling must occur within a narrow range of temperatures to reduce product composition changes from overheating or partial condensation or plugging of lines from condensed products. Residence times must be kept at a minimum to reduce further reaction chemistries. Pyrolysis vapors also form aerosols that are carried far downstream and can pass through filters resulting in build-up in downstream locations. The co-produced bio-char and ash from the pyrolysis process can lead to plugging of the sample lines, and must be filtered out at temperature, even with the use of cyclonic separators. A practical approach for considerations and sampling system design, as well as lessons learned are integrated into the hot analytical sampling system of the National Renewable Energy Laboratory's (NREL) Thermochemical Process Development Unit (TCPDU) to provide industrially relevant demonstrations of thermochemical transformations of biomass feedstocks at the pilot scale.

Pyrolysis and dehalogenation of plastics from waste electrical and electronic equipment (WEEE): a review.

Science.gov (United States)

Yang, Xiaoning; Sun, Lushi; Xiang, Jun; Hu, Song; Su, Sheng

2013-02-01

Plastics from waste electrical and electronic equipment (WEEE) have been an important environmental problem because these plastics commonly contain toxic halogenated flame retardants which may cause serious environmental pollution, especially the formation of carcinogenic substances polybrominated dibenzo dioxins/furans (PBDD/Fs), during treat process of these plastics. Pyrolysis has been proposed as a viable processing route for recycling the organic compounds in WEEE plastics into fuels and chemical feedstock. However, dehalogenation procedures are also necessary during treat process, because the oils collected in single pyrolysis process may contain numerous halogenated organic compounds, which would detrimentally impact the reuse of these pyrolysis oils. Currently, dehalogenation has become a significant topic in recycling of WEEE plastics by pyrolysis. In order to fulfill the better resource utilization of the WEEE plastics, the compositions, characteristics and dehalogenation methods during the pyrolysis recycling process of WEEE plastics were reviewed in this paper. Dehalogenation and the decomposition or pyrolysis of WEEE plastics can be carried out simultaneously or successively. It could be 'dehalogenating prior to pyrolysing plastics', 'performing dehalogenation and pyrolysis at the same time' or 'pyrolysing plastics first then upgrading pyrolysis oils'. The first strategy essentially is the two-stage pyrolysis with the release of halogen hydrides at low pyrolysis temperature region which is separate from the decomposition of polymer matrixes, thus obtaining halogenated free oil products. The second strategy is the most common method. Zeolite or other type of catalyst can be used in the pyrolysis process for removing organohalogens. The third strategy separate pyrolysis and dehalogenation of WEEE plastics, which can, to some degree, avoid the problem of oil value decline due to the use of catalyst, but obviously, this strategy may increase the cost of

Magnesium Sulfate as a Key Mineral for the Detection of Organic Molecules on Mars Using Pyrolysis

Science.gov (United States)

Francois, P.; Szopa, C.; Buch, A.; Coll, P.; McAdam, A. C.; Mahaffy, P. R.; Freissinet, C.; Glavin, D. P.; Navarro-Gonzalez, R.; Cabane, M.

2016-01-01

Pyrolysis of soil or rock samples is the preferred preparation technique used on Mars to search for organic molecules up today. During pyrolysis, oxichlorines present in the soil of Mars release oxidant species that alter the organic molecules potentially contained in the samples collected by the space probes.This process can explain the difficulty experienced by in situ exploration probes to detect organic materials in Mars soil samples until recently. Within a few months, the Curiosity rover should reach and analyze for the first time soils rich in sulfates which could induce a different behavior of the organics during the pyrolysis compared with the types of soils analyzed up today. For this reason, we systematically studied the pyrolysis of organic molecules trapped in magnesium sulfate, in the presence or absence of calcium perchlorate. Our results show that organics trapped in magnesium sulfate can undergo some oxidation and sulfuration during the pyrolysis. But these sulfates are also shown to protect organics trapped inside the crystal lattice and/or present in fluid inclusions from the oxidation induced by the decomposition of calcium perchlorate and probably other oxychlorine phases currently detected on Mars. Trapped organics may also be protected from degradation processes induced by other minerals present in the sample, at least until these organics are released from the pyrolyzed sulfate mineral (700C in our experiment). Hence, we suggest magnesium sulfate as one of the minerals to target in priority for the search of organic molecules by the Curiosity and ExoMars 2018 rovers.

A comprehensive study of methyl decanoate pyrolysis

International Nuclear Information System (INIS)

Pyl, Steven P.; Van Geem, Kevin M.; Puimège, Philip; Sabbe, Maarten K.; Reyniers, Marie-Françoise; Marin, Guy B.

2012-01-01

The thermal decomposition of methyl decanoate (MD) was studied in a bench-scale pyrolysis set-up equipped with a dedicated on-line analysis section including a GC × GC-FID/(TOF-MS). This analysis section enables quantitative and qualitative on-line analyses of the entire reactor effluent with high level of detail including measurement of formaldehyde and water. The reactor temperature was varied from 873 K to 1123 K at a fixed pressure of 1.7 bar and a fixed residence time of 0.5 s, for both high (10mol N 2 /mol MD ) and low (0.6mol N 2 /mol MD ) nitrogen dilution. Thus covering a wide conversion range in both dilution regimes. In these experiments, significant amounts of large linear olefins and unsaturated esters were observed at lower temperatures, the amounts of which decreased at higher temperatures in favor of permanent gasses (CO, CO 2 , CH 4 ) and light olefins. At the highest temperatures more than 5 wt% of mono-aromatic and poly-aromatic components were observed. The acquired dataset was used to validate 3 recently published microkinetic models which were developed to model oxidation and/or pyrolysis of methyl decanoate. The results showed that these models accurately predict the product distribution, although important discrepancies were observed for some major products such as certain unsaturated esters, CO 2 and H 2 O. Reaction path analyses and CBS-QB3 quantum-chemical calculations are presented and discussed in order to explain the observed differences. -- Highlights: ► New extensive experimental dataset for the pyrolysis of methyl decanoate in a tubular reactor. ► A dedicated separation section including on-line GC × GC allows to obtain quantitative data for over 150 components. ► High level ab-initio calculations for important reactions of the methyl decanoate decomposition. ► Identification of missing reactions/reaction families/inaccurate kinetics in the presently available kinetic models.

Pyrolysis Model Development for a Multilayer Floor Covering

Directory of Open Access Journals (Sweden)

Mark B. McKinnon

2015-09-01

Full Text Available Comprehensive pyrolysis models that are integral to computational fire codes have improved significantly over the past decade as the demand for improved predictive capabilities has increased. High fidelity pyrolysis models may improve the design of engineered materials for better fire response, the design of the built environment, and may be used in forensic investigations of fire events. A major limitation to widespread use of comprehensive pyrolysis models is the large number of parameters required to fully define a material and the lack of effective methodologies for measurement of these parameters, especially for complex materials. The work presented here details a methodology used to characterize the pyrolysis of a low-pile carpet tile, an engineered composite material that is common in commercial and institutional occupancies. The studied material includes three distinct layers of varying composition and physical structure. The methodology utilized a comprehensive pyrolysis model (ThermaKin to conduct inverse analyses on data collected through several experimental techniques. Each layer of the composite was individually parameterized to identify its contribution to the overall response of the composite. The set of properties measured to define the carpet composite were validated against mass loss rate curves collected at conditions outside the range of calibration conditions to demonstrate the predictive capabilities of the model. The mean error between the predicted curve and the mean experimental mass loss rate curve was calculated as approximately 20% on average for heat fluxes ranging from 30 to 70 kW·m−2, which is within the mean experimental uncertainty.

Coal pyrolysis under synthesis gas, hydrogen and nitrogen

Energy Technology Data Exchange (ETDEWEB)

Ariunaa, A.; Li Bao-Qing; Li Wen; Purevsuren, B. (and others) [Chinese Academy of Sciences, Taiyuan (China)

2007-02-15

Chinese Xundian, Mongolian Shiveeovoo lignites and Khoot oil shale are pyrolyzed under synthesis gas (SG) at temperature range from 400 to 800{sup o}C for lignite and from 300 to 600{sup o}C for oil shale with heating rate of 10{sup o}C/min in a fixed bed reactor. The results were compared with those obtained by pyrolysis under hydrogen and nitrogen. The results showed that unlike pyrolysis at high pressure, there are only slight different in the yields of char and tar among pyrolyses under various gases at room pressure for lignite, while higher liquid yield with lower yields of char and gas was obtained in pyrolysis of oil shale under SG and H{sub 2} than under N{sub 2}. It is found that the pyrite S can be easily removed to partially convert to organic S under various gaseous atmosphere and the total sulfur removal for oil shale is much less than lignite, which might be related to its high ash content. The higher total sulfur removal and less organic S content in the presence of SG in comparison with those under N{sub 2} and even under H{sub 2} in pyrolysis of Xundian lignite might result from the action of CO in SG. However, CO does not show its function in pyrolysis of Khoot oil shale, which might also be related to the high ash content. The results reported show the possibility of using synthesis gas instead of pure hydrogen as the reactive gas for coal hydropyrolysis. 11 refs., 4 figs., 6 tabs.

Catalytic Fast Pyrolysis of Biomass Impregnated with Potassium Phosphate in a Hydrogen Atmosphere for the Production of Phenol and Activated Carbon

Science.gov (United States)

Lu, Qiang; Zhang, Zhen-xi; Wang, Xin; Guo, Hao-qiang; Cui, Min-shu; Yang, Yong-ping

2018-01-01

A new technique was proposed to co-produce phenol and activated carbon (AC) from catalytic fast pyrolysis of biomass impregnated with K3PO4 in a hydrogen atmosphere, followed by activation of the pyrolytic solid residues. Lab-scale catalytic fast pyrolysis experiments were performed to quantitatively determine the pyrolytic product distribution, as well as to investigate the effects of several factors on the phenol production, including pyrolysis atmosphere, catalyst type, biomass type, catalytic pyrolysis temperature, and catalyst impregnation content. In addition, the pyrolytic solid residues were activated to prepare ACs with high specific surface areas. The results indicated that phenol could be obtained due to the synergistic effects of K3PO4 and hydrogen atmosphere, with the yield and selectivity reaching 5.3 wt% and 17.8% from catalytic fast pyrolysis of poplar wood with 8 wt% K3PO4 at 550°C in a hydrogen atmosphere. This technique was adaptable to different woody materials for phenol production. Moreover, gas product generated from the pyrolysis process was feasible to be recycled to provide the hydrogen atmosphere, instead of extra hydrogen supply. In addition, the pyrolytic solid residue was suitable for AC preparation, using CO2 activation method, the specific surface area was as high as 1,605 m2/g. PMID:29515994

The structure and pyrolysis product distribution of lignite from different sedimentary environment

International Nuclear Information System (INIS)

Liu, Peng; Zhang, Dexiang; Wang, Lanlan; Zhou, Yang; Pan, Tieying; Lu, Xilan

2016-01-01

Highlights: • Carbon structure of three lignites was measured by solid "1"3C NMR. • Effect of carbon structure on pyrolysis product distribution was studied. • Tar yield is influenced by aliphatic carbon and oxygen functional group. • C1–C4 content of pyrolysis gas is related to CH_2/CH_3 ratio. - Abstract: Low-temperature pyrolysis is an economically efficient method for lignite to obtain coal tar and improve its combustion calorific value. The research on the distribution of pyrolysis product (especially coal tar yield) plays an important role in energy application and economic development in the now and future. Pyrolysis test was carried out in a tube reactor at 873 K for 15 min. The structure of the lignite was measured by solid "1"3C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR). The thermal analysis was analyzed by thermo-gravimetric (TG) analyzer. The results show that the pyrolysis product distribution is related to the breakage of branch structures of aromatic ring in lignites from different sedimentary environment. The gas yield and composition are related to the decomposition of carbonyl group and the breakage of aliphatic carbon. The tar yield derived from lignite pyrolysis follows the order: Xianfeng lignite (XF, 13.67 wt.%) > Xiaolongtan lignite (XLT, 7.97 wt.%) > Inner Mongolia lignite (IM, 6.30 wt.%), which is mainly influenced by the aliphatic carbon contents, the CH_2/CH_3 ratio and the oxygen functional groups in lignite. The pyrolysis water yield depends on the decomposition of oxygen functional groups. IM has the highest content of oxygen-linked carbon so that the pyrolysis water yield derived from IM is the highest (9.20 wt.%), and is far more than that from the other two lignites.

Well-to-wheels analysis of fast pyrolysis pathways with the GREET model.

Energy Technology Data Exchange (ETDEWEB)

Han, J.; Elgowainy, A.; Palou-Rivera, I.; Dunn, J.B.; Wang, M.Q. (Energy Systems)

2011-12-01

The pyrolysis of biomass can help produce liquid transportation fuels with properties similar to those of petroleum gasoline and diesel fuel. Argonne National Laboratory conducted a life-cycle (i.e., well-to-wheels [WTW]) analysis of various pyrolysis pathways by expanding and employing the Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. The WTW energy use and greenhouse gas (GHG) emissions from the pyrolysis pathways were compared with those from the baseline petroleum gasoline and diesel pathways. Various pyrolysis pathway scenarios with a wide variety of possible hydrogen sources, liquid fuel yields, and co-product application and treatment methods were considered. At one extreme, when hydrogen is produced from natural gas and when bio-char is used for process energy needs, the pyrolysis-based liquid fuel yield is high (32% of the dry mass of biomass input). The reductions in WTW fossil energy use and GHG emissions relative to those that occur when baseline petroleum fuels are used, however, is modest, at 50% and 51%, respectively, on a per unit of fuel energy basis. At the other extreme, when hydrogen is produced internally via reforming of pyrolysis oil and when bio-char is sequestered in soil applications, the pyrolysis-based liquid fuel yield is low (15% of the dry mass of biomass input), but the reductions in WTW fossil energy use and GHG emissions are large, at 79% and 96%, respectively, relative to those that occur when baseline petroleum fuels are used. The petroleum energy use in all scenarios was restricted to biomass collection and transportation activities, which resulted in a reduction in WTW petroleum energy use of 92-95% relative to that found when baseline petroleum fuels are used. Internal hydrogen production (i.e., via reforming of pyrolysis oil) significantly reduces fossil fuel use and GHG emissions because the hydrogen from fuel gas or pyrolysis oil (renewable sources) displaces that from fossil fuel

Enhancing biogas production of corn stover by fast pyrolysis pretreatment.

Science.gov (United States)

Wang, Fang; Zhang, Deli; Wu, Houkai; Yi, Weiming; Fu, Peng; Li, Yongjun; Li, Zhihe

2016-10-01

A new thermo-chemical pretreatment by a lower temperature fast pyrolysis (LTFP) was applied to promote anaerobic digestion (AD) efficiency of corn stover (CS). The pretreatment experiment was performed by a fluidized bed pyrolysis reactor at 180, 200 and 220°C with a carrier gas flow rate of 4 and 3m(3)/h. The components characteristics, Scanning Electron Microscope (SEM) images and Crystal Intensity (CrI) of the pretreated CS were tested to explore effectiveness of the pretreatment. The results showed that the cumulative methane production at 180°C for 4 and 3m(3)/h were 199.8 and 200.3mL/g TS, respectively. As compared to the untreated CS, the LTFP pretreatment significantly (a<0.05) increased the methane production by 18.07% and 18.33%, respectively. Methane production was well fitted by the Gompertz models, and the maximum methane potential and AD efficiency was obtained at 180°C for 3m(3)/h. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyrolysis of forestry biomass by-products in Greece

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A.

1999-06-01

This article summarizes the technical characteristics of a biomass pyrolysis pilot plant recently constructed in central Greece. It highlights the considerations involved in achieving successful pyrolysis technology and environmental and developmental goals, by reviewing technical and nontechnical barriers associated with biomass treatment technology in Greece. Data from the start-up phase of the plant operation are presented and some aspects of the process are outlined. The capacity of the plant is 1200 1450 kg hr, based on wet biomass (Arbutus Unedo) and the pyrolysis temperature is approximately 400{sup o}C. Char yield is 1418 % weight on dry basis and is of good quality consisting of 76{sup o}C with heat content 6760 kcal kg. Bio-oil includes 63% C and its heat content is 6250 kcal kg. (author)

Fuel production from microwave assisted pyrolysis of coal with carbon surfaces

International Nuclear Information System (INIS)

Mushtaq, Faisal; Mat, Ramli; Ani, Farid Nasir

2016-01-01

Highlights: • MW heating of coal was carried out with uniformly distributed carbon surfaces. • The effects of carbon loading, MW power and N 2 flow rate were investigated. • Heating profile, pyrolysis products are influenced by the process variables. • Highest coal-tar obtained when final temperature sustained for longer duration. • Coal-tar is mainly composed of aromatics and saturated aliphatics hydrocarbons. - Abstract: In this study, coal solids were subjected to Microwave (MW) pyrolysis conditions. Coconut Activated Carbon (CAC) solids used as a MW absorber was distributed uniformly over coal solids to reduce hotspots. Three process parameters; CAC loading, MW power and N 2 flow rate were studies on pyrolysis heating performance. The highest coal-tar yield of 18.59 wt% was obtained with 600 W, 75 wt% CAC loading and 4 Liter per Minute (LPM) of N 2 flow rate. This improved coal-tar yield is mainly of the fact that higher MW power and CAC loading produced sustained pyrolysis conditions for longer duration for the complete conversion of pyrolysis solids. The coal-tar was composed mainly of aromatics (naphthalenes, benzenes and xylene) and saturated aliphatics (alkanes and alkenes) hydrocarbons. The gas produced from pyrolysis of coal is mainly of H 2 40.23–65.22 vol%.

Thermo-Catalytic Pyrolysis of Waste Plastics from End of Life Vehicle

Directory of Open Access Journals (Sweden)

Miskolczi Norbert

2016-01-01

Full Text Available Pyrolysis of waste plastics is widely used recycling method. Owing to the end-of-life vehicles regulations, 95% of passenger cars and vehicles must reused/recovered after the dismantling. Pyrolysis of waste polyethylene and polypropylene obtained from end-of-life vehicles was investigated in a continuously stirred batch reactor using 500 and 600°C temperatures. To ensure the pyrolysis reactions the tested catalysts (5% of ZSM-5, HZSM-5, Ni-ZSM-5 and Fe-ZSM-5 were added directly to the mixtures of raw materials. Products of pyrolysis were separated into gases, pyrolysis oil and heavy oil, which was further analyzed by gas-chromatography, Fourier transformed infrared spectroscopy and other standardized methods. Based on the results it was concluded, that the catalysts significantly increase the yields of volatile products, and modify their composition. Especially the alkane/alkene ratio, the methane concentration and the concentration of branched hydrocarbon could be affected by the applied catalysts. Ni-ZSM-5 catalyst had the highest activity in methane production, while HZSM-5 catalyst proved effective in isomerization reactions. Using H-ZSM-5, Ni-ZSM-5, and Fe-ZSM-5 catalyst notably decreased average molecular weight of pyrolysis oils and significantly higher aromatic content was observed.

Novel technique for coal pyrolysis and hydrogenation product analysis. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Pfefferle, L.D.; Boyle, J.

1993-03-15

A microjet reactor coupled to a VUV photoionization time-of-flight mass spectrometer has been used to obtain species measurements during high temperature pyrolysis and oxidation of a wide range of hydrocarbon compounds ranging from allene and acetylene to cyclohexane, benzene and toluene. Initial work focused on calibration of the technique, optimization of ion collection and detection and characterization of limitations. Using the optimized technique with 118 nm photoionization, intermediate species profiles were obtained for analysis of the hydrocarbon pyrolysis and oxidation mechanisms. The ``soft`` ionization, yielding predominantly molecular ions, allowed the study of reaction pathways in these high temperature systems where both sampling and detection challenges are severe. Work has focused on the pyrolysis and oxidative pyrolysis of aliphatic and aromatic hydrocarbon mixtures representative of coal pyrolysis and hydropyrolysis products. The detailed mass spectra obtained during pyrolysis and oxidation of hydrocarbon mixtures is especially important because of the complex nature of the product mixture even at short residence times and low primary reactant conversions. The combustion community has advanced detailed modeling of pyrolysis and oxidation to the C4 hydrocarbon level but in general above that size uncertainties in rate constant and thermodynamic data do not allow us to a priori predict products from mixed hydrocarbon pyrolyses using a detailed chemistry model. For pyrolysis of mixtures of coal-derived liquid fractions with a large range of compound structures and molecular weights in the hundreds of amu the modeling challenge is severe. Lumped models are possible from stable product data.

Thermogravimetric and calorimetric characteristics during co-pyrolysis of municipal solid waste components.

Science.gov (United States)

Ansah, Emmanuel; Wang, Lijun; Shahbazi, Abolghasem

2016-10-01

The thermogravimetric and calorimetric characteristics during pyrolysis of wood, paper, textile and polyethylene terephthalate (PET) plastic in municipal solid wastes (MSW), and co-pyrolysis of biomass-derived and plastic components with and without torrefaction were investigated. The active pyrolysis of the PET plastic occurred at a much higher temperature range between 360°C and 480°C than 220-380°C for the biomass derived components. The plastic pyrolyzed at a heating rate of 10°C/min had the highest maximum weight loss rate of 18.5wt%/min occurred at 420°C, followed by 10.8wt%/min at 340°C for both paper and textile, and 9.9wt%/min at 360°C for wood. At the end of the active pyrolysis stage, the final mass of paper, wood, textile and PET was 28.77%, 26.78%, 21.62% and 18.31%, respectively. During pyrolysis of individual MSW components at 500°C, the wood required the least amount of heat at 665.2J/g, compared to 2483.2J/g for textile, 2059.4J/g for paper and 2256.1J/g for PET plastic. The PET plastic had much higher activation energy of 181.86kJ/mol, compared to 41.47kJ/mol for wood, 50.01kJ/mol for paper and 36.65kJ/mol for textile during pyrolysis at a heating rate of 10°C/min. H2O and H2 peaks were observed on the MS curves for the pyrolysis of three biomass-derived materials but there was no obvious H2O and H2 peaks on the MS curves of PET plastic. There was a significant interaction between biomass and PET plastic during co-pyrolysis if the biomass fraction was dominant. The amount of heat required for the co-pyrolysis of the biomass and plastic mixture increased with the increase of plastic mass fraction in the mixture. Torrefaction at a proper temperature and time could improve the grindability of PET plastic. The increase of torrefaction temperature and time did not affect the temperature where the maximum pyrolytic rates occurred for both biomass and plastic but decreased the maximum pyrolysis rate of biomass and increased the maximum pyrolysis

PYROLYSIS OF ZINC CONTAMINATED BIOMASS FROM PHYTOREMEDIATION

OpenAIRE

Özkan, Aysun; Günkaya, Zerrin; Banar, Müfide; Kulaç, Alev; Yalçın, Gülser; Taşpınar, Kadriye; Altay, Abdullah

2015-01-01

The objective of this study was to stabilize of zinc (Zn) from soil to pyrolysis solid product. For this aim, phytoremediation and pyrolysis were sequentially applied. In the first stage of the study, phytoremediation was first applied to zinc contaminated soil via  sunflower (Helianthus annuus), corn (Zea mays) and rape (Brassica napus), After harvesting, the plants were pyrolyzed at 500°C with the heating rate of 35 °C/min in a fixed bed stainless steel (380 S) 240 cm3 reactor. The phytorem...

Olive bagasse (Olea europa L.) pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Sensoz, S.; Demiral, I. [Osmangazi Univ., Eskisehir (Turkey). Dept. of Chemical Engineering; Gercel, H.F. [Anadolu Univ., Eskisehir (Turkey). Dept. of Chemical Engineering

2006-02-15

Olive bagasse (Olea europea L.) was pyrolysed in a fixed-bed reactor. The effects of pyrolysis temperature, heating rate, particle size and sweep gas flow rates on the yields of the products were investigated. Pyrolysis runs were performed using pyrolysis temperatures between 350 and 550 {sup o}C with heating rates of 10 and 50 {sup o}C min{sup -} {sup 1}. The particle size and sweep gas flow rate varied in the ranges 0.224-1.8 mm and 50-200 cm{sup 3} min {sup -1}, respectively. The bio-oil obtained at 500 {sup o}C was analysed and at this temperature the liquid product yield was the maximum. The various characteristics of bio-oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of the bio-oil with heating value of 31.8 MJ kg{sup -1} was established as CH{sub 1.65}O{sub 0.25}N{sub 0.03}. The chemical characterization showed that the bio-oil obtained from olive bagasse may be potentially valuable as a fuel and chemical feedstock. (author)

Investigation of waste biomass co-pyrolysis with petroleum sludge using a response surface methodology.

Science.gov (United States)

Hu, Guangji; Li, Jianbing; Zhang, Xinying; Li, Yubao

2017-05-01

The treatment of waste biomass (sawdust) through co-pyrolysis with refinery oily sludge was carried out in a fixed-bed reactor. Response surface method was applied to evaluate the main and interaction effects of three experimental factors (sawdust percentage in feedstock, temperature, and heating rate) on pyrolysis oil and char yields. It was found that the oil and char yields increased with sawdust percentage in feedstock. The interaction between heating rate and sawdust percentage as well as between heating rate and temperature was significant on the pyrolysis oil yield. The higher heating value of oil originated from sawdust during co-pyrolysis at a sawdust/oily sludge ratio of 3:1 increased by 5 MJ/kg as compared to that during sawdust pyrolysis alone, indicating a synergistic effect of co-pyrolysis. As a result, petroleum sludge can be used as an effective additive in the pyrolysis of waste biomass for improving its energy recovery. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of additives on the co-pyrolysis of municipal solid waste and paper sludge by using thermogravimetric analysis.

Science.gov (United States)

Fang, Shiwen; Yu, Zhaosheng; Lin, Yan; Lin, Yousheng; Fan, Yunlong; Liao, Yanfen; Ma, Xiaoqian

2016-06-01

By using thermogravimetric analysis (TGA), the effects of different additives (MgO, Al2O3 and ZnO) on the pyrolysis characteristics and activation energy of municipal solid waste (MSW), paper sludge (PS) and their blends in N2 atmosphere had been investigated in this study. The experiments resulted that these additives were effective in reducing the initial temperature and activation energy. However, not all the additives were beneficial to reduce the residue mass and enhance the index D. For the different ratios of MSW and PS, the same additive even had the different influences. The catalytic effects of additives were not obvious and the pyrolysis became difficult with the increase of the proportion of PS. Based on all the contrast of the pyrolysis characteristics, MgO was the best additive and 70M30P was the best ratio, respectively. Copyright © 2016 Elsevier Ltd. All rights reserved.

Low-temperature pyrolysis of oily sludge: roles of Fe/Al-pillared bentonites

Directory of Open Access Journals (Sweden)

Jia Hanzhong

2017-09-01

Full Text Available Pyrolysis is potentially an effective treatment of oily sludge for oil recovery, and the addition of a catalyst is expected to affect its pyrolysis behavior. In the present study, Fe/Al-pillared bentonite with various Fe/Al ratios as pyrolysis catalyst is prepared and characterized by XRD, N2 adsorption, and NH3-TPD. The integration of Al and Fe in the bentonite interlayers to form pillared clay is evidenced by increase in the basal spacing. As a result, a critical ratio of Fe/Al exists in the Fe/Al-pillared bentonite catalytic pyrolysis for oil recovery from the sludge. The oil yield increases with respect to increase in Fe/Al ratio of catalysts, then decreases with further increasing of Fe/Al ratio. The optimum oil yield using 2.0 wt% of Fe/Al 0.5-pillared bentonite as catalyst attains to 52.46% compared to 29.23% without catalyst addition in the present study. In addition, the addition of Fe/Al-pillared bentonite catalyst also improves the quality of pyrolysis-produced oil and promotes the formation of CH4. Fe/Al-pillared bentonite provides acid center in the inner surface, which is beneficial to the cracking reaction of oil molecules in pyrolysis process. The present work implies that Fe/Al-pillared bentonite as addictive holds great potential in industrial pyrolysis of oily sludge.

Pyrolysis behaviors and kinetic studies on Eucalyptus residues using thermogravimetric analysis

International Nuclear Information System (INIS)

Chen, Zhihua; Zhu, Quanjie; Wang, Xun; Xiao, Bo; Liu, Shiming

2015-01-01

Highlights: • The first study on pyrolysis characteristics and kinetic of Eucalyptus residues. • Pyrolysis process can be divided into three stages using differential DTG method. • A new modified discrete DAEM showed better than Gaussian DAEM for kinetic studies. • Variations of activation energy reveal the mechanism change during pyrolysis process. - Abstract: The pyrolysis behaviors and kinetics of Eucalyptus leaves (EL), Eucalyptus bark (EB) and Eucalyptus sawdust (ESD) were investigated by using thermogravimetric analysis (TGA) technique. Three stages for EL, EB and ESD pyrolysis have been divided using differential derivative thermogravimetric (DDTG) method and the second stage is the main pyrolysis process with approximately 86.93% (EL), 88.96% (EB) and 97.84% (ESD) weight loss percentages. Kinetic parameters of Gaussian distributed activation energy model (DAEM) for EL, EB and ESD pyrolysis are: distributed centers (E_0) of 141.15 kJ/mol (EL), 149.21 kJ/mol (EB), 175.79 kJ/mol (ESD), standard deviations (σ) of 18.35 kJ/mol (EL), 18.37 kJ/mol (EB), 14.41 kJ/mol (ESD) and pre-exponential factors (A) of 1.15E+10 s"−"1 (EL), 4.34E+10 s"−"1 (EB), 7.44E+12 s"−"1 (ESD). A new modified discrete DAEM was performed and showed excellent fits to experimental data than Gaussian DAEM. According to the modified discrete DAEM, the activation energies are in ranges of 122.67–308.64 kJ/mol, 118.72–410.80 kJ/mol and 108.39–192.93 kJ/mol for EL, EB and ESD pyrolysis, respectively. The pre-exponential factors of discrete DAEM have wide ranges of 4.84E+13–6.12E+22 s"−"1 (EL), 1.91E+12–4.51E+25 s"−"1 (EB) and 63.43–4.36E+11 s"−"1 (ESD). The variation of activation energy versus conversion reveals the mechanism change during pyrolysis process. The kinetic data would be of immense benefit to model, design and develop suitable thermo-chemical systems for the application of Eucalyptus residues.

Pyrolysis oil upgrading for Co-processing in standard refinery units

NARCIS (Netherlands)

De Miguel Mercader, F.

2010-01-01

This thesis considers the route that comprises the upgrading of pyrolysis oil (produced from lingo-cellulosic biomass) and its further co-processing in standard refineries to produce transportation fuels. In the present concept, pyrolysis oil is produced where biomass is available and then

Pyrolysis of polystyrene waste in the presence of activated carbon in conventional and microwave heating using modified thermocouple.

Science.gov (United States)

Prathiba, R; Shruthi, M; Miranda, Lima Rose

2018-06-01

Pyrolysis process was experimented using two types of heating source, namely conventional and microwave. Polystyrene (PS) plastic waste was used as feedstock in a batch reactor for both the conventional (slow pyrolysis) and microwave pyrolysis. The effect of activated carbon to polystyrene ratio on (i) yield of oil, gas and residues (ii) reaction temperature (iii) reaction time were studied. Quality of oil from pyrolysis of polystyrene were assessed for the possible applicability in fuel production. Microwave power of 450 W and polymer to activated carbon ratio of 10:1, resulted in the highest oil yield of 93.04 wt.% with a higher heating value of 45 MJ kg -1 and a kinematic viscosity of 2.7 cSt. Microwave heating when compared to conventional heating method, exhibits a reaction temperature and time of 330 °C in 5.5 min, whereas in conventional heating system it was 418 °C in 60 min. The gas chromatography-mass spectrometry analysis of liquid oil from microwave pyrolysis predominantly yields alkenes of 8.44 wt.%, α-methyl styrene 0.96 wt.%, condensed ring aromatics 23.21 wt.% and benzene derivatives 26.77 wt.% when the polystyrene to activated carbon ratio was 10:1. Significant factor of using microwave heating is the amount of energy converted (kWh) is lesser than conventional heating. Copyright © 2018 Elsevier Ltd. All rights reserved.

Pyrolysis of Pine Wood

DEFF Research Database (Denmark)

Fjellerup, Jan Søren; Ahrenfeldt, Jesper; Henriksen, Ulrik Birk

2005-01-01

In this study, pinewood has been pyrolyzed using a fixed heating rate with a variable end-temperature. The pyrolysis process has been simulated using a mechanism with three parallel reactions for the formation of char, gas and tar. First order irreversible kinetics is assumed. This kind of model ...

THE ROLE OF INTRAMOLECULAR TIES ENERGY IN THE PYROLYSIS PROCESS OF PET

Directory of Open Access Journals (Sweden)

P. Iu. Salikov

2014-01-01

Full Text Available Summary. Recycling plastic waste to focus on. The main type of used products made of polyethylene terephthalate (PET is a container from the various types of beverages. There was considered a possibility of waste of PET (bottles, bottles, packaging containers by pyrolysis. Most of the proposed methods are not suitable for recycling (recycling of waste consumption contamination. Purpose - to develop technological foundations and optimum modes waste PET to obtain useful secondary products, taking into account the energy of chemical intramolecular bonds. Applied scientific basis of recycling PET into useful forms of secondary products, in particular the establishment of the collapse of the intramolecular bonds, depending on the temperature of the pyrolysis method of mathematical processing - differentiation of polynomial equations change in the degree of pyrolysis temperature-dependent. The optimum modes of processing. The block diagram of apparatus for processing contaminated waste PET pyrolysis methods of control processing in accordance with the specified composition of secondary products. The possibility of controlling the amount and types of fuel components of secondary products due to measurable parameters of the pyrolysis process. The effective temperature pyrolysis of waste PET with the CCA-tures energy intramolecular bonds.

Kinetic studies of co-pyrolysis of rubber seed shell with high density polyethylene

International Nuclear Information System (INIS)

Chin, Bridgid Lai Fui; Yusup, Suzana; Al Shoaibi, Ahmed; Kannan, Pravin; Srinivasakannan, Chandrasekar; Sulaiman, Shaharin Anwar

2014-01-01

Highlights: • Co-pyrolysis of biomass and plastic waste in thermogravimetric analyzer. • Investigation of thermal degradation behavior in different feedstocks. • Synergistic effect of the biomass and plastic waste mixture is investigated. • Kinetic parameters using one step integral method are determined. - Abstract: This paper investigates the thermal degradation behavior of rubber seed shell (RSS), high density polyethylene (HDPE), and the HDPE/RSS mixtures (0.2:0.8 weight ratio) using thermogravimetric analyzer under non-isothermal condition in argon atmosphere at flowrate of 100 ml min −1 . Cellulose, hemicellulose, and lignin are also analyzed in this study for comparison of pyrolysis behavior with RSS. The experiments were conducted at different heating rates of 10, 20, 30, and 50 K min −1 in the temperature range of 323–1173 K. The kinetic data is generated based on first order rate of reaction. It is observed that the thermal degradation behavior of the main components in biomass such as hemicellulose, cellulose, and lignin differs during pyrolysis process due to the structural differences that leads to distinctive pathways of degradation of feedstock. It is found that there are one, two, and three stages of decomposition occurring in HDPE, RSS, and HDPE/RSS mixtures respectively during the pyrolysis process. The remaining solid residue increases with an increase in heating rate regardless of the type of samples used. The activation energies (E A ) for RSS, HDPE, HDPE/RSS mixtures are 46.94–63.21, 242.13–278.14, and 49.14–83.11 kJ mol −1 respectively for the range of heating rate studied

Comparison of ethanol production from corn cobs and switchgrass following a pyrolysis-based biorefinery approach.

Science.gov (United States)

Luque, Luis; Oudenhoven, Stijn; Westerhof, Roel; van Rossum, Guus; Berruti, Franco; Kersten, Sascha; Rehmann, Lars

2016-01-01

One of the main obstacles in lignocellulosic ethanol production is the necessity of pretreatment and fractionation of the biomass feedstocks to produce sufficiently pure fermentable carbohydrates. In addition, the by-products (hemicellulose and lignin fraction) are of low value, when compared to dried distillers grains (DDG), the main by-product of corn ethanol. Fast pyrolysis is an alternative thermal conversion technology for processing biomass. It has recently been optimized to produce a stream rich in levoglucosan, a fermentable glucose precursor for biofuel production. Additional product streams might be of value to the petrochemical industry. However, biomass heterogeneity is known to impact the composition of pyrolytic product streams, as a complex mixture of aromatic compounds is recovered with the sugars, interfering with subsequent fermentation. The present study investigates the feasibility of fast pyrolysis to produce fermentable pyrolytic glucose from two abundant lignocellulosic biomass sources in Ontario, switchgrass (potential energy crop) and corn cobs (by-product of corn industry). Demineralization of biomass removes catalytic centers and increases the levoglucosan yield during pyrolysis. The ash content of biomass was significantly decreased by 82-90% in corn cobs when demineralized with acetic or nitric acid, respectively. In switchgrass, a reduction of only 50% for both acids could be achieved. Conversely, levoglucosan production increased 9- and 14-fold in corn cobs when rinsed with acetic and nitric acid, respectively, and increased 11-fold in switchgrass regardless of the acid used. After pyrolysis, different configurations for upgrading the pyrolytic sugars were assessed and the presence of potentially inhibitory compounds was approximated at each step as double integral of the UV spectrum signal of an HPLC assay. The results showed that water extraction followed by acid hydrolysis and solvent extraction was the best upgrading strategy

Ecotoxicological characterization of biochars: role of feedstock and pyrolysis temperature.

Science.gov (United States)

Domene, X; Enders, A; Hanley, K; Lehmann, J

2015-04-15

Seven contrasting feedstocks were subjected to slow pyrolysis at low (300 or 350°C) and high temperature (550 or 600°C), and both biochars and the corresponding feedstocks tested for short-term ecotoxicity using basal soil respiration and collembolan reproduction tests. After a 28-d incubation, soil basal respiration was not inhibited but stimulated by additions of feedstocks and biochars. However, variation in soil respiration was dependent on both feedstock and pyrolysis temperature. In the last case, respiration decreased with pyrolysis temperature (r=-0.78; pmanagement recommendations. Copyright © 2014 Elsevier B.V. All rights reserved.

Modernized Approach for Generating Reproducible Heterogeneity Using Transmitted-Light for Flow Visualization Experiments

Science.gov (United States)

Jones, A. A.; Holt, R. M.

2017-12-01

Image capturing in flow experiments has been used for fluid mechanics research since the early 1970s. Interactions of fluid flow between the vadose zone and permanent water table are of great interest because this zone is responsible for all recharge waters, pollutant transport and irrigation efficiency for agriculture. Griffith, et al. (2011) developed an approach where constructed reproducible "geologically realistic" sand configurations are deposited in sandfilled experimental chambers for light-transmitted flow visualization experiments. This method creates reproducible, reverse graded, layered (stratified) thin-slab sand chambers for point source experiments visualizing multiphase flow through porous media. Reverse-graded stratification of sand chambers mimic many naturally occurring sedimentary deposits. Sandfilled chambers use light as nonintrusive tools for measuring water saturation in two-dimensions (2-D). Homogeneous and heterogeneous sand configurations can be produced to visualize the complex physics of the unsaturated zone. The experimental procedure developed by Griffith, et al. (2011) was designed using now outdated and obsolete equipment. We have modernized this approach with new Parker Deadel linear actuator and programed projects/code for multiple configurations. We have also updated the Roper CCD software and image processing software with the latest in industry standards. Modernization of transmitted-light source, robotic equipment, redesigned experimental chambers, and newly developed analytical procedures have greatly reduced time and cost per experiment. We have verified the ability of the new equipment to generate reproducible heterogeneous sand-filled chambers and demonstrated the functionality of the new equipment and procedures by reproducing several gravity-driven fingering experiments conducted by Griffith (2008).

Catalytic flash pyrolysis of oil-impregnated-wood and jatropha cake using sodium based catalysts

KAUST Repository

Imran, Ali

2015-11-24

Catalytic pyrolysis of wood with impregnated vegetable oil was investigated and compared with catalytic pyrolysis of jatropha cake making use of sodium based catalysts to produce a high quality bio-oil. The catalytic pyrolysis was carried out in two modes: in-situ catalytic pyrolysis and post treatment of the pyrolysis vapors. The in-situ catalytic pyrolysis was carried out in an entrained flow reactor system using a premixed feedstock of Na2CO3 and biomass and post treatment of biomass pyrolysis vapor was conducted in a downstream fixed bed reactor of Na2CO3/γ-Al2O3. Results have shown that both Na2CO3 and Na2CO3/γ-Al2O3 can be used for the production of a high quality bio-oil from catalytic pyrolysis of oil-impregnated-wood and jatropha cake. The catalytic bio-oil had very low oxygen content, water content as low as 1wt.%, a neutral pH, and a high calorific value upto 41.8MJ/kg. The bio-oil consisted of high value chemical compounds mainly hydrocarbons and undesired compounds in the bio-oil were either completely removed or considerably reduced. Increasing the triglycerides content (vegetable oil) in the wood enhanced the formation of hydrocarbons in the bio-oil. Post treatment of the pyrolysis vapor over a fixed bed of Na2CO3/γ-Al2O3 produced superior quality bio-oil compared to in-situ catalytic pyrolysis with Na2CO3. This high quality bio-oil may be used as a precursor in a fractionating process for the production of alternative fuels. © 2015 Elsevier B.V.

Sugarcane Bagasse Pyrolysis in a Carbon Dioxide Atmosphere with Conventional and Microwave-Assisted Heating

Energy Technology Data Exchange (ETDEWEB)

Lin, Bo-Jhih; Chen, Wei-Hsin, E-mail: weihsinchen@gmail.com [Department of Aeronautics and Astronautics, National Cheng Kung University, Tainan, Taiwan (China)

2015-02-04

Pyrolysis is an important thermochemical method to convert biomass into bio-oil. In this study, the pyrolysis of sugarcane bagasse in a CO{sub 2} atmosphere under conventional and microwave-assisted heating is investigated to achieve CO{sub 2} utilization. In the microwave pyrolysis, charcoal is used as the microwave absorber to aid in pyrolysis reactions. The results indicate that the yields of pyrolysis products are greatly influenced by the heating modes. In the conventional heating, the prime product is bio-oil and its yield is in the range of 51–54 wt%, whereas biochar is the major product in microwave-assisted heating and its yield ranges from 61 to 84 wt%. Two different absorber blending ratios of 0.1 and 0.3 are considered in the microwave pyrolysis. The solid yield decreases when the absorber blending ratio decreases from 0.3 to 0.1, while the gas and liquid yields increase. This is attributed to more energy consumed for bagasse pyrolysis at the lower blending ratio. Hydrogen is produced under the microwave pyrolysis and its concentration is between 2 and 12 vol%. This arises from the fact that the secondary cracking of vapors and the secondary decomposition of biochar in an environment with microwave irradiation is easier than those with conventional heating.

Catalytic pyrolysis of LDPE using modified vermiculite as a catalyst

International Nuclear Information System (INIS)

Bezerra, Franciel Aureliano; Figueiredo, Aneliese Lunguinho; Araujo, Antonio Souza de; Guedes, Ana Paula de Melo Alves

2016-01-01

Low density polyethylene (LDPE) is one of the most commonly-used polymers currently, and the great quantity of this polymer produced results in tons of waste that must be treated. We studied the thermocatalytic pyrolysis of LDPE with a modified clay vermiculite catalyst as an alternative for treatment of waste. The clay was treated with a solution of nitric acid at different concentrations and calcined at 400 °C. The materials were characterized by X-ray diffraction, thermogravimetry, nitrogen adsorption, and energy dispersive spectroscopy. Thermal and thermocatalytic pyrolysis were carried out in a microreactor coupled with GC/MS at 500 °C. The aim of the polymeric waste pyrolysis is the obtainment of light hydrocarbons (C<16), which can be used in the chemical and petrochemical industry, through breaks in the polymer chain. The results were satisfactory, with an increase in yield for light hydrocarbons by using catalysts reaching up to 71.4% of products with C<16, whereas thermal pyrolysis resulted in only 25.8%. (author)

Safety analysis report for the Hanford Critical Mass Laboratory: Supplement No. 2. Experiments with heterogeneous assemblies

International Nuclear Information System (INIS)

Gore, B.F.; Davenport, L.C.

1981-04-01

Factors affecting the safety of criticality experiments using heterogeneous assemblies are described and assessed. It is concluded that there is no substantial change in safety from experiments already being routinely performed at the Critical Mass Laboratory (CML), and that laboratory and personnel safety are adequately provided by the combination of engineered and administrative safety limits enforced at the CML. This conclusion is based on the analysis of operational controls, potential hazards, and the consequences of accidents. Contingencies considered that could affect nuclear criticality include manual changes in fuel loadings, water flooding, fire, explosion, loss of services, earthquake, windstorm, and flood. Other potential hazards considered include radiation exposure to personnel, and potential releases within the Assembly Room and outside to the environment. It is concluded that the Maximum Credible Nuclear Burst of 3 x 10 18 fissions (which served as the design basis for the CML) is valid for heterogeneous assemblies as well as homogeneous assemblies. This is based upon examination of the results of reactor destructive tests and the results of the SL-1 reactor destructive accident. The production of blast effects which might jeopardize the CML critical assembly room (of thick reinforced concrete) is not considered credible due to the extreme circumstances required to produce blast effects in reactor destructive tests. Consequently, it is concluded that, for experiments with heterogeneous assemblies, the consequences of the Maximum Credible Burst are unchanged from those previously estimated for experiments with homogeneous systems

Co-pyrolysis of rice straw and Polyethylene Terephthalate (PET) using a fixed bed drop type pyrolyzer

Science.gov (United States)

Izzatie, N. I.; Basha, M. H.; Uemura, Y.; Hashim, M. S. M.; Amin, N. A. M.; Hamid, M. F.

2017-10-01

In this work, co-pyrolysis of rice straw and polyethylene terephthalate (PET) was carried out at different temperatures (450,500,550, and 600°C) at ratio 1:1 by using fixed bed drop-type pyrolyzer. The purpose of this work is to determine the effect of pyrolysis temperature on the product yield. As the temperature increased, the pyrolysis oil increased until it reaches certain high temperature (600°C), the pyrolysis oil decreased as of more NCG were produced. The temperature 550°C is considered as the optimum pyrolysis temperature since it produced the highest amount of pyrolysis oil with 36 wt.%. In pyrolysis oil, the calorific value (13.98kJ/g) was low because of the presence of high water content (52.46 wt.%). Main chemicals group from pyrolysis oil were an aldehyde, ketones, acids, aromatics, and phenol and all compound have abundant of hydrogen and carbon were identified. Co-pyrolysis of rice straw and PET produced a higher amount of carbon oxides and recycling back the NCG could increase liquid and char yields.

Catalytic flash pyrolysis of oil-impregnated-wood and jatropha cake using sodium based catalysts

KAUST Repository

Imran, Ali; Bramer, Eddy A.; Seshan, Kulathuiyer; Brem, Gerrit

2015-01-01

Catalytic pyrolysis of wood with impregnated vegetable oil was investigated and compared with catalytic pyrolysis of jatropha cake making use of sodium based catalysts to produce a high quality bio-oil. The catalytic pyrolysis was carried out in two

Catalytic oxidative pyrolysis of spent organic ion exchange resins from nuclear power plants

International Nuclear Information System (INIS)

Sathi Sasidharan, N.; Deshingkar, D.S.; Wattal, P.K.; Shirsat, A.N.; Bharadwaj, S.R.

2005-08-01

The spent IX resins from nuclear power reactors are highly active solid wastes generated during operations of nuclear reactors. Catalytic oxidative pyrolysis of these resins can lead to high volume reduction of these wastes. Low temperature pyrolysis of transition metal ion loaded IX resins in presence of nitrogen was carried out in order to optimize catalyst composition to achieve maximum weight reduction. Thermo gravimetric analysis of the pyrolysis residues was carried out in presence of air in order to compare the oxidative characteristics of transition metal oxide catalysts. Copper along with iron, chromium and nickel present in the spent IX resins gave the most efficient catalyst combination for catalytic and oxidative pyrolysis of the residues. During low temperature catalytic pyrolysis, 137 Cesium volatility was estimated to be around 0.01% from cationic resins and around 0.1% from anionic resins. During oxidative pyrolysis at 700 degC, nearly 10 to 40% of 137 Cesium was found to be released to off gases depending upon type of resin and catalyst loaded on to it. The oxidation of pyrolytic residues at 700 degC gave weight reduction of 15% for cationic resins and 93% for anionic resins. Catalytic oxidative pyrolysis is attractive for reducing weight and volume of spent cationic resins from PHWRs and VVERs. (author)

FAST PYROLYSIS PROCESS OF ORANGE SOLID WASTE. FACTORS INFLUENCE IN THE PROCESS

Directory of Open Access Journals (Sweden)

Leonardo Aguiar Trujillo

2015-04-01

Full Text Available The orange processing industry generates high volumes of solid residue. This residue has been used in animal feeding and biochemical processes. A possible energy use of the waste can be thermochemical fast pyrolysis process. The objective was to determine the influence of the heating rate and temperature in the process of rapid pyrolysis of orange solid residue. In the process a design, 2k full factorial experiment was used, evaluating the influence of the independent variables and its interactions on the answers, using a 95 % significance level. We found that temperature is the most significant influence on the responses parameter having significant influence on the yields to: gas, coal, tar and the calorific value of the gas and the heating rate does not influence the answers. Finally, the interaction affects the gas yield. The results obtained in this study are: Rgas (19 – 38 %, Rchar (25 – 42 %, Ralq (6 – 12 %, PCIgas entre (140 – 1050 kJ/m3N.

Microwave pyrolysis for conversion of materials to energy : A review

International Nuclear Information System (INIS)

Mokhtar, M.; Omar, R.; MOhammad Salleh, M.A.; Idris, A.

2009-01-01

Full text: The disposal of wastes in Malaysia is becoming a serious problem in many industrialized and public sectors. This is due to the high production of waste such as municipal solid waste, sludge from waste water treatment plants, agricultural waste and other used non-biodegradable products such as plastics and tyres. These wastes although are reused as compost, fuel, recycled and so on, there are still abundant left. These leftovers pose problems such as heavy metal leaching, leachates, green house gas emissions and mosquito breeding grounds. The disposal cost of these wastes sometimes can be costly at up to RM 2,200/ ton such as petroleum sludge by Kualiti Alam. Several methods have been used to convert these residues to energy via thermal treatment such as combustion, incineration and gasification. However, pyrolysis becomes one of the popular methods as the alternative to the wastes disposal recently. Not only energy (as gas) is produced, by-products such as chemical feedstock and solid absorbent can be produced. The use of microwave for pyrolysis, although relatively new for waste treatment, has several advantages compared to conventional heating. This includes easy control of the heating process, time saving, higher heating efficiency, etc. Tyre microwave pyrolysis plant in UK is known as the earliest plant using microwave technology to breakdown polymer in used tyres. Since 1990s, there are many patents for microwave pyrolysis. The processes are based on microwave pyrolysis of waste include coffee hulls, wood, coal, sewage sludge, hospital waste, plastic wastes, corn cobs and rice straw. The most important factors influencing the yield of product during the pyrolysis is temperature in range from 500 to 1000 degree Celsius according to product preference. High temperature favors gas products; whereas lower temperature favors liquid products. Comparatively, microwave pyrolysis produced gas with higher hydrogen and carbon monoxide (syngas) content compared

Pyrolysis of softwood carbohydrates in a fluidized bed reactor.

Science.gov (United States)

Aho, Atte; Kumar, Narendra; Eränen, Kari; Holmbom, Bjarne; Hupa, Mikko; Salmi, Tapio; Murzin, Dmitry Yu

2008-09-01

In the present work pyrolysis of pure pine wood and softwood carbohydrates, namely cellulose and galactoglucomannan (the major hemicellulose in coniferous wood), was conducted in a batch mode operated fluidized bed reactor. Temperature ramping (5 degrees C/min) was applied to the heating until a reactor temperature of 460 degrees C was reached. Thereafter the temperature was kept until the release of non-condensable gases stopped. The different raw materials gave significantly different bio-oils. Levoglucosan was the dominant product in the cellulose pyrolysis oil. Acetic acid was found in the highest concentrations in both the galactoglucomannan and in the pine wood pyrolysis oils. Acetic acid is most likely formed by removal of O-acetyl groups from mannose units present in GGM structure.

Thermogravimetric analysis and fast pyrolysis of Milkweed.

Science.gov (United States)

Kim, Seung-Soo; Agblevor, Foster A

2014-10-01

Pyrolysis of Milkweed was carried out in a thermogravimetric analyzer and a bubbling fluidized bed reactor. Total liquid yield of Milkweed pyrolysis was between 40.74% and 44.19 wt% between 425 °C and 550 °C. The gas yield increased from 27.90 wt% to 33.33 wt% with increasing reaction temperature. The higher heating values (HHV) of the Milkweed bio-oil were relatively high (30.33-32.87 MJ/kg) and varied with reaction temperature, feeding rate and fluidization velocity. The selectivity for CO2 was highest within non-condensable gases, and the molar ratio of CO2/CO was about 3 at the different reaction conditions. The (13)C NMR analysis, of the bio-oil showed that the relative concentration carboxylic group and its derivatives was higher at 425 °C than 475 °C, which resulted in slightly higher oxygen content in bio-oil. The pH of aqueous phase obtained at 475 °C was 7.37 which is the highest reported for any lignocellulosic biomass pyrolysis oils. Copyright © 2014 Elsevier Ltd. All rights reserved.

Production of bio-oils from wood by flash pyrolysis; Herstellung von Bio-Oelen aus Holz in einer Flash-Pyrolyseanlage

Energy Technology Data Exchange (ETDEWEB)

Meier, D; Ollesch, T [Bundesforschungsanstalt fuer Forst- und Holzwirtschaft, Hamburg (Germany). Inst. fuer Holzchemie und Chemische Technologie des Holzes; Gerdes, C; Kaminsky, W [Hamburg Univ. (Germany). Inst. fuer Technische und Makromolekulare Chemie (ITMCh)

1998-09-01

Flash pyrolysis is a medium-temperature process (around 475 C) in which biomass is heated up rapidly in the absence of oxygen. The pyrolysis products are cooled down rapidly, condensing into a reddish-brown liquid with around half the calorific value of a conventional heating oil. In contrast to conventional charcoal production, flash pyrolysis is a modern process whose process parameters enure high liquid yields. Modern fluidized-bed reactors for flash pyrolysis of biomass tend to have high heating rates and short times of residue. In the `Hamburg process`, fluidized-bed reactors are used successfully for pyrolysis of plastics. A flash pyrolysis plant for biomass treatment was constructed in cooperation with Hamburg University with funds provided by the `Bundesstiftung Umwelt`. This contribution describes the first series of experiments, mass balances and oil analyses using beech wood as material to be pyrolyzed. (orig./SR) [Deutsch] Flash-Pyrolyse ist ein Mitteltemperatur-Prozess (ca. 475 C), in dem Biomasse unter Sauerstoffausschluss sehr schnell erhitzt wird. Die entstehenden Pyrolyseprodukte werden schnell abgekuehlt und kondensieren zu einer roetlich-braunen Fluessigkeit, die etwa die Haelfte des Heizwertes eines konventionellen Heizoeles besitzt. Flash-Pyrolyse ist, im Gegensatz zur konventionellen Holzverkohlung, ein modernes Verfahren, dessen spezielle Verfahrensparameter hohe Fluessigausbeuten ermoeglichen. Hohe Aufheizraten, verbunden mit kurzen Verweilzeiten, werden mit stationaeren Wirbelbettreaktoren erzielt die gegenwaertig vorwiegend fuer die Flash-Pyrolyse von Biomasse eingesetzt werden. Im `Hamburger Verfahren` haben sich Wirbelbettreaktoren im Bereich der Kunststoffpyrolyse bewaehrt. Daher wurde in Zusammenarbeit mit der Universitaet Hamburg und finanzieller Foerderung der Bundesstiftung Umwelt eine Flash-Pyrolyseanlage fuer Biomasse gebaut: In dieser Arbeit werden erste Versuchsreihen, Massenbilanzen und Oelanalysen aus der Pyrolyse von

Life cycle assessment of gasoline and diesel produced via fast pyrolysis and hydroprocessing

International Nuclear Information System (INIS)

Hsu, David D.

2012-01-01

Pyrolysis of biomass followed by hydroprocessing may provide infrastructure-compatible transportation fuels. In this work, a life cycle assessment (LCA) of the production of gasoline and diesel from forest residues via fast pyrolysis and hydroprocessing, from production of the feedstock to end use of the fuel in a vehicle, is performed. The fast pyrolysis and subsequent hydrotreating and hydrocracking processes are based on a Pacific Northwest National Laboratory design report. Stages other than biofuels conversion, including forest residue production and harvesting, preprocessing, feedstock transportation, fuel distribution, and vehicle operation, are based on previous work. Probability distribution functions are assumed for parameters involved in the pyrolysis process for Monte Carlo uncertainty analysis. This LCA for the production of gasoline and diesel via pyrolysis and upgrading assumes grid electricity is used and supplemental natural gas is supplied to the hydrogen plant. Gasoline and diesel produced via pyrolysis are estimated to have greenhouse gas (GHG) emissions of CO 2 equivalent of 117 g km −1 and 98 g km −1 , respectively, and net energy value (NEV) of 1.09 MJ km −1 and 0.92 MJ km −1 , respectively. All values from the uncertainty analysis have lower GHG emissions and higher NEV than conventional gasoline in 2005. Grid electricity and natural gas used account for 81% of the net GHG emissions in the base case. An evaluation of a case with biomass-derived electricity shows significant improvement in GHG emissions. -- Highlights: ► We conduct a life cycle assessment of a biomass-to-fuels pyrolysis pathway. ► Pyrolysis fuels are estimated to emit fewer greenhouse gases than conventional gasoline. ► Fewer greenhouse gases would be emitted if the pyrolysis process generated its own electricity from biomass.

Specialists' workshop on fast pyrolysis of biomass

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

This workshop brought together most of those who are currently working in or have published significant findings in the area of fast pyrolysis of biomass or biomass-derived materials, with the goal of attaining a better understanding of the dominant mechanisms which produce olefins, oxygenated liquids, char, and tars. In addition, background papers were given in hydrocarbon pyrolysis, slow pyrolysis of biomass, and techniques for powdered-feedstock preparation in order that the other papers did not need to introduce in depth these concepts in their presentations for continuity. In general, the authors were requested to present summaries of experimental data with as much interpretation of that data as possible with regard to mechanisms and process variables such as heat flux, temperatures, partial pressure, feedstock, particle size, heating rates, residence time, etc. Separate abstracts have been prepared of each presentation for inclusion in the Energy Data Base. (DMC)

Slow pyrolysis of pistachio shell

Energy Technology Data Exchange (ETDEWEB)

Apaydin-Varol, Esin; Putun, Ersan; Putun, Ayse E [Anadolu University, Eskisehir (Turkey). Department of Chemical Engineering

2007-08-15

In this study, pistachio shell is taken as the biomass sample to investigate the effects of pyrolysis temperature on the product yields and composition when slow pyrolysis is applied in a fixed-bed reactor at atmospheric pressure to the temperatures of 300, 400, 500, 550, 700{sup o}C. The maximum liquid yield was attained at about 500-550{sup o}C with a yield of 20.5%. The liquid product obtained under this optimum temperature and solid products obtained at all temperatures were characterized. As well as proximate and elemental analysis for the products were the basic steps for characterization, column chromatography, FT-IR, GC/MS and SEM were used for further characterization. The results showed that liquid and solid products from pistachio shells show similarities with high value conventional fuels. 31 refs., 9 figs., 1 tab.

A review of the toxicity of biomass pyrolysis liquids formed at low temperatures

Energy Technology Data Exchange (ETDEWEB)

Diebold, J P [Thermalchemie, Inc., Lakewood, CO (United States)

1997-04-01

The scaleup of biomass fast pyrolysis systems to large pilot and commercial scales will expose an increasingly large number of personnel to potential health hazards, especially during the evaluation of the commercial use of the pyrolysis condensates. Although the concept of fast pyrolysis to optimize liquid products is relatively new, low-temperature pyrolysis processes have been used over the aeons to produce charcoal and liquid by-products, e.g., smoky food flavors, food preservatives, and aerosols containing narcotics, e.g., nicotine. There are a number of studies in the historical literature that concern the hazards of acute and long-term exposure to smoke and to the historical pyrolysis liquids formed at low temperatures. The reported toxicity of smoke, smoke food flavors, and fast pyrolysis oils is reviewed. The data found for these complex mixtures suggest that the toxicity may be less than that of the individual components. It is speculated that there may be chemical reactions that take place that serve to reduce the toxicity during aging. 81 refs.

Microwave-assisted co-pyrolysis of brown coal and corn stover for oil production.

Science.gov (United States)

Zhang, Yaning; Fan, Liangliang; Liu, Shiyu; Zhou, Nan; Ding, Kuan; Peng, Peng; Anderson, Erik; Addy, Min; Cheng, Yanling; Liu, Yuhuan; Li, Bingxi; Snyder, John; Chen, Paul; Ruan, Roger

2018-07-01

The controversial synergistic effect between brown coal and biomass during co-pyrolysis deserves further investigation. This study detailed the oil production from microwave-assisted co-pyrolysis of brown coal (BC) and corn stover (CS) at different CS/BC ratios (0, 0.33, 0.50, 0.67, and 1) and pyrolysis temperatures (500, 550, and 600 °C). The results showed that a higher CS/BC ratio resulted in higher oil yield, and a higher pyrolysis temperature increased oil yield for brown coal and coal/corn mixtures. Corn stover and brown coal showed different pyrolysis characteristics, and positive synergistic effect on oil yield was observed only at CS/BC ratio of 0.33 and pyrolysis temperature of 600 °C. Oils from brown coal mainly included hydrocarbons and phenols whereas oils from corn stover and coal/corn mixtures were dominated by ketones, phenols, and aldehydes. Positive synergistic effects were observed for ketones, aldehydes, acids, and esters whereas negative synergistic effects for hydrocarbons, phenols and alcohols. Copyright © 2018 Elsevier Ltd. All rights reserved.

Polycyclic aromatic hydrocarbons (PAHs) and volatile organic compounds (VOCs) mitigation in the pyrolysis process of waste tires using CO₂ as a reaction medium.

Science.gov (United States)

Kwon, Eilhann E; Oh, Jeong-Ik; Kim, Ki-Hyun

2015-09-01

Our work reported the CO2-assisted mitigation of PAHs and VOCs in the thermo-chemical process (i.e., pyrolysis). To investigate the pyrolysis of used tires to recover energy and chemical products, the experiments were conducted using a laboratory-scale batch-type reactor. In particular, to examine the influence of the CO2 in pyrolysis of a tire, the pyrolytic products including C1-5-hydrocarbons (HCs), volatile organic carbons (VOCs), and polycyclic aromatic hydrocarbons (PAHs) were evaluated qualitatively by gas chromatography (GC) with mass spectroscopy (MS) as well as with a thermal conductivity detector (TCD). The mass balance of the pyrolytic products under various pyrolytic conditions was established on the basis of their weight fractions of the pyrolytic products. Our experimental work experimentally validated that the amount of gaseous pyrolytic products increased when using CO2 as a pyrolysis medium, while substantially altering the production of pyrolytic oil in absolute content (7.3-17.2%) and in relative composition (including PAHs and VOCs). Thus, the co-feeding of CO2 in the pyrolysis process can be considered an environmentally benign and energy efficient process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Flash pyrolysis fuel oil: BIO-POK

Energy Technology Data Exchange (ETDEWEB)

Gust, S. [Neste Oy, Porvoo (Finland)

1995-12-31

Flash pyrolysis oil from Ensyn Tech., Canada and Union Fenosa, Spain was combusted with simple pressure atomisation equipment commonly used with light fuel oils in intermediate size (0.1-1 MW) boilers. With a number of modifications to the combustion system, carbon monoxide (CO) and nitrous oxide (NO{sub x}) could be reduced to acceptable levels: CO < 30 ppm and NO{sub x} < 140 ppm. Particulate emissions which were initially very high (Bacharach 4-5) were reduced (Bach. 2-3) by system changes but are still higher than from light fuel oil (Bach. <1). The modifications to the combustion system were: acid resistant progressive cavity pump, higher oil preheat temperature and higher oil pressure than for light fuel oils, refractory section between burner and boiler warmed up to at least 800 deg C. In addition, it was necessary to store pyrolysis oil samples under inert conditions to prevent oxidation and to rinse nozzles with alcohol after shutdown to prevent coking. The complexity and cost of these system modifications are considered to be too great for current grades of flash pyrolysis oil to be sold as a light fuel oil replacement. Improvements to fuel quality will be necessary. The main improvements are lowering of viscosity and improving of stability

Flash pyrolysis fuel oil: BIO-POK

Energy Technology Data Exchange (ETDEWEB)

Gust, S [Neste Oy, Porvoo (Finland)

1996-12-31

Flash pyrolysis oil from Ensyn Tech., Canada and Union Fenosa, Spain was combusted with simple pressure atomisation equipment commonly used with light fuel oils in intermediate size (0.1-1 MW) boilers. With a number of modifications to the combustion system, carbon monoxide (CO) and nitrous oxide (NO{sub x}) could be reduced to acceptable levels: CO < 30 ppm and NO{sub x} < 140 ppm. Particulate emissions which were initially very high (Bacharach 4-5) were reduced (Bach. 2-3) by system changes but are still higher than from light fuel oil (Bach. <1). The modifications to the combustion system were: acid resistant progressive cavity pump, higher oil preheat temperature and higher oil pressure than for light fuel oils, refractory section between burner and boiler warmed up to at least 800 deg C. In addition, it was necessary to store pyrolysis oil samples under inert conditions to prevent oxidation and to rinse nozzles with alcohol after shutdown to prevent coking. The complexity and cost of these system modifications are considered to be too great for current grades of flash pyrolysis oil to be sold as a light fuel oil replacement. Improvements to fuel quality will be necessary. The main improvements are lowering of viscosity and improving of stability

Catalytic Pyrolysis of Waste Plastic Mixture

Science.gov (United States)

Sembiring, Ferdianta; Wahyu Purnomo, Chandra; Purwono, Suryo

2018-03-01

Inorganic waste especially plastics still become a major problem in many places. Low biodegradability of this materials causes the effort in recycling become very difficult. Most of the municipal solid waste (MSW) recycling facilities in developing country only use composting method to recover the organic fraction of the waste, while the inorganic fraction is still untreated. By pyrolysis, plastic waste can be treated to produce liquid fuels, flammable gas and chars. Reduction in volume and utilization of the liquid and gas as fuel are the major benefits of the process. By heat integration actually this process can become a self-sufficient system in terms of energy demand. However, the drawback of this process is usually due to the diverse type of plastic in the MSW creating low grade of liquid fuel and harmful gases. In this study, the mixture of plastics i.e. polypropylene (PP) and polyethylene terephthalate (PET) is treated using pyrolysis with catalyst in several operating temperature. PET is problematic to be treated using pyrolysis due to wax-like byproduct in liquid which may cause pipe clogging. The catalyst is the mixture of natural zeolite and bentonite which is able to handle PP and PET mixture feed to produce high grade liquid fuels in terms of calorific value and other fuel properties.

A steady state model of agricultural waste pyrolysis: A mini review.

Science.gov (United States)

Trninić, M; Jovović, A; Stojiljković, D

2016-09-01

Agricultural waste is one of the main renewable energy resources available, especially in an agricultural country such as Serbia. Pyrolysis has already been considered as an attractive alternative for disposal of agricultural waste, since the technique can convert this special biomass resource into granular charcoal, non-condensable gases and pyrolysis oils, which could furnish profitable energy and chemical products owing to their high calorific value. In this regard, the development of thermochemical processes requires a good understanding of pyrolysis mechanisms. Experimental and some literature data on the pyrolysis characteristics of corn cob and several other agricultural residues under inert atmosphere were structured and analysed in order to obtain conversion behaviour patterns of agricultural residues during pyrolysis within the temperature range from 300 °C to 1000 °C. Based on experimental and literature data analysis, empirical relationships were derived, including relations between the temperature of the process and yields of charcoal, tar and gas (CO2, CO, H2 and CH4). An analytical semi-empirical model was then used as a tool to analyse the general trends of biomass pyrolysis. Although this semi-empirical model needs further refinement before application to all types of biomass, its prediction capability was in good agreement with results obtained by the literature review. The compact representation could be used in other applications, to conveniently extrapolate and interpolate these results to other temperatures and biomass types. © The Author(s) 2016.

Energy and resource utilization of deinking sludge pyrolysis

International Nuclear Information System (INIS)

Lou, Rui; Wu, Shubin; Lv, Gaojin; Yang, Qing

2012-01-01

The thermochemical conversion technique was applied in deinking sludge from the pulp and papermaking industrial to indagate the utilization of sludge biomass to energy, and the pyrolysis characteristics and pyrolytic products of deinking sludge were studied with thermogravimetric analysis (TGA) and pyrolysis coupled with gas chromatograph–mass spectrometer (Py-GC/MS). The static tubular furnace as an applied industrial research was used to study deinking sludge pyrolysis. The solid, gas and liquid of products was characterized by electron probe microanalysis (EPMA), gas chromatograph (GC) and gas chromatograph–mass (GC/MS), respectively. The results revealed that the weight-loss process of deinking sludge was a non-isothermal reaction and composed of four stages, i.e. dewater stage, volatile releasing stage, carbon burnout stage and some calcium carbonate decomposition. Pyrolytic products from deinking sludge in the static tubular furnace were comprised of the gaseous (29.78%), condensed liquid (bio-oil, 24.41%) and solid residues (45.81%). The volatiles from deinking sludge pyrolyzing were almost aromatic hydrocarbons, i.e. styrene, toluene and benzene and few acids and the solid was calcium carbonate (CaCO 3 ) that can be reused as paper filler. Deinking sludge was converted into high-grade fuel and chemicals by means of thermochemical conversion techniques, hence, pyrolysis of paper deinking sludge had a promising development on the comprehensive utilization.

Production of brown algae pyrolysis oils for liquid biofuels depending on the chemical pretreatment methods

International Nuclear Information System (INIS)

Choi, Joonhyuk; Choi, Jae-Wook; Suh, Dong Jin; Ha, Jeong-Myeong; Hwang, Ji Won; Jung, Hyun Wook; Lee, Kwan-Young; Woo, Hee-Chul

2014-01-01

Highlights: • Pyrolysis of Saccharina japonica, brown algae to produce hydrocarbons. • Sulfuric acid pretreatment of macroalgae to remove inorganic elements. • CaCl 2 treatment of macroalgae to remove valuable fucoidan. • Sulfuric acid pretreatment suppressed the formation of large biochar chunks. • The pretreatment methods allowed the continuous operation of pyrolysis. - Abstract: Based on observations of rapidly growing biochar in fluidization beds, kelp (Saccharina japonica), a species of brown algae, was pretreated for the efficient operation of pyrolysis processes to produce pyrolysis oils. The removal of catalytically active inorganic minerals and the softening of polymeric seaweed structures were performed by means of chemical treatments, including a CaCl 2 treatment to isolate valuable and sticky fucoidan and a sulfuric acid treatment to remove catalytically active minerals. The sulfuric acid pretreatment significantly reduced the inorganic elements but did not significantly affect the properties of the pyrolysis oil compared to the non-treated kelp pyrolysis oil. Whereas the non-treated kelp produced significantly large chunks of biochar, which hindered the continuous operation of pyrolysis, the kelp treated with sulfuric acid did not produce aggregated large particles of biochar, thereby offering a means of developing reliable continuous pyrolysis processes

High-pressure pyrolysis and oxidation of ethanol

DEFF Research Database (Denmark)

Hashemi, Hamid; Christensen, Jakob M.; Glarborg, Peter

2018-01-01

against the present data as well as ignition delay times and flame speed measurements from literature. The model predicted the onset of fuel conversion and the composition of products from the flow reactor experiments fairly well. It also predicted well ignition delays above 900 K whereas it overpredicted...... reported flame speeds slightly. The results of sensitivity analyses revealed the importance of the reaction between ethanol and the hydroperoxyl radical for ignition at high pressure and intermediate temperatures. An accurate determination of the rate coefficients for this reaction is important to improve......The pyrolysis and oxidation of ethanol has been investigated at temperatures of 600–900 K, a pressure of 50 bar and residence times of 4.3–6.8 s in a laminar flow reactor. The experiments, conducted with mixtures highly diluted in nitrogen, covered fuel-air equivalence ratios (Φ) of 0.1, 1.0, 43...

Production of phenolic-rich bio-oil from catalytic fast pyrolysis of biomass using magnetic solid base catalyst

International Nuclear Information System (INIS)

Zhang, Zhi-bo; Lu, Qiang; Ye, Xiao-ning; Li, Wen-tao; Hu, Bin; Dong, Chang-qing

2015-01-01

Highlights: • Phenolic-rich bio-oil was selectively produced from catalytic fast pyrolysis of biomass using magnetic solid base catalyst. • The actual yield of twelve major phenolic compounds reached 43.9 mg/g. • The peak area% of all phenolics reached 68.5% at the catalyst-to-biomass ratio of 7. • The potassium phosphate/ferroferric oxide catalyst possessed promising recycling properties. - Abstract: A magnetic solid base catalyst (potassium phosphate/ferroferric oxide) was prepared and used for catalytic fast pyrolysis of poplar wood to selectively produce phenolic-rich bio-oil. Pyrolysis–gas chromatography/mass spectrometry experiments were conducted to investigate the effects of pyrolysis temperature and catalyst-to-biomass ratio on the product distribution. The actual yields of important pyrolytic products were quantitatively determined by the external standard method. Moreover, recycling experiments were performed to determine the re-utilization abilities of the catalyst. The results showed that the catalyst exhibited promising activity to selectively produce phenolic-rich bio-oil, due to its capability of promoting the decomposition of lignin to generate phenolic compounds and meanwhile inhibiting the devolatilization of holocellulose. The maximal phenolic yield was obtained at the pyrolysis temperature of 400 °C and catalyst-to-biomass ratio of 2. The concentration of the phenolic compounds increased monotonically along with the increasing of the catalyst-to-biomass ratio, with the peak area% value increasing from 28.1% in the non-catalytic process to as high as 68.5% at the catalyst-to-biomass ratio of 7. The maximal total actual yield of twelve quantified major phenolic compounds was 43.9 mg/g, compared with the value of 29.0 mg/g in the non-catalytic process. In addition, the catalyst could be easily recovered and possessed promising recycling properties.

Pyrolysis of aseptic packages (tetrapak) in a laboratory screw type reactor and secondary thermal/catalytic tar decomposition

Energy Technology Data Exchange (ETDEWEB)

Haydary, J., E-mail: juma.haydary@stuba.sk [Institute of Chemical and Environmental Engineering, Faculty of Chemical and Food Technology, Slovak University of Technology, Radlinského 9, 812 37 Bratislava (Slovakia); Susa, D.; Dudáš, J. [Institute of Chemical and Environmental Engineering, Faculty of Chemical and Food Technology, Slovak University of Technology, Radlinského 9, 812 37 Bratislava (Slovakia)

2013-05-15

Highlights: ► Pyrolysis of aseptic packages was carried out in a laboratory flow reactor. ► Distribution of tetrapak into the product yields was obtained. ► Composition of the pyrolysis products was estimated. ► Secondary thermal and catalytic decomposition of tars was studied. ► Two types of catalysts (dolomite and red clay marked AFRC) were used. - Abstract: Pyrolysis of aseptic packages (tetrapak cartons) in a laboratory apparatus using a flow screw type reactor and a secondary catalytic reactor for tar cracking was studied. The pyrolysis experiments were realized at temperatures ranging from 650 °C to 850 °C aimed at maximizing of the amount of the gas product and reducing its tar content. Distribution of tetrapak into the product yields at different conditions was obtained. The presence of H{sub 2}, CO, CH{sub 4}, CO{sub 2} and light hydrocarbons, HCx, in the gas product was observed. The Aluminum foil was easily separated from the solid product. The rest part of char was characterized by proximate and elemental analysis and calorimetric measurements. The total organic carbon in the tar product was estimated by elemental analysis of tars. Two types of catalysts (dolomite and red clay marked AFRC) were used for catalytic thermal tar decomposition. Three series of experiments (without catalyst in a secondary cracking reactor, with dolomite and with AFRC) at temperatures of 650, 700, 750, 800 and 850 °C were carried out. Both types of catalysts have significantly affected the content of tars and other components in pyrolytic gases. The effect of catalyst on the tetrapack distribution into the product yield on the composition of gas and on the total organic carbon in the tar product is presented in this work.

Kinetic study of corn straw pyrolysis: comparison of two different three-pseudocomponent models.

Science.gov (United States)

Li, Zhengqi; Zhao, Wei; Meng, Baihong; Liu, Chunlong; Zhu, Qunyi; Zhao, Guangbo

2008-11-01

With heating rates of 20, 50 and 100 K min(-1), the thermal decomposition of corn straw samples (corn stalks skins, corn stalks cores, corn bracts and corn leaves) were studied using thermogravimetric analysis. The maximum pyrolysis rates increased with the heating rate increasing and the temperature at the peak pyrolysis rate also increased. Assuming the addition of three independent parallel reactions, corresponding to three pseudocomponents linked to the hemicellulose, cellulose and lignin, two different three-pseudocomponent models were used to simulate the corn straw pyrolysis. Model parameters of pyrolysis were given. It was found that the three-pseudocomponent model with n-order kinetics was more accurate than the model with first-order kinetics at most cases. It showed that the model with n-order kinetics was more accurate to describe the pyrolysis of the hemicellulose.

A Heterogeneous Distributed Virtual Geographic Environment—Potential Application in Spatiotemporal Behavior Experiments

Directory of Open Access Journals (Sweden)

Shen Shen

2018-02-01

Full Text Available Due to their strong immersion and real-time interactivity, helmet-mounted virtual reality (VR devices are becoming increasingly popular. Based on these devices, an immersive virtual geographic environment (VGE provides a promising method for research into crowd behavior in an emergency. However, the current cheaper helmet-mounted VR devices are not popular enough, and will continue to coexist with personal computer (PC-based systems for a long time. Therefore, a heterogeneous distributed virtual geographic environment (HDVGE could be a feasible solution to the heterogeneous problems caused by various types of clients, and support the implementation of spatiotemporal crowd behavior experiments with large numbers of concurrent participants. In this study, we developed an HDVGE framework, and put forward a set of design principles to define the similarities between the real world and the VGE. We discussed the HDVGE architecture, and proposed an abstract interaction layer, a protocol-based interaction algorithm, and an adjusted dead reckoning algorithm to solve the heterogeneous distributed problems. We then implemented an HDVGE prototype system focusing on subway fire evacuation experiments. Two types of clients are considered in the system: PC, and all-in-one VR. Finally, we evaluated the performances of the prototype system and the key algorithms. The results showed that in a low-latency local area network (LAN environment, the prototype system can smoothly support 90 concurrent users consisting of PC and all-in-one VR clients. HDVGE provides a feasible solution for studying not only spatiotemporal crowd behaviors in normal conditions, but also evacuation behaviors in emergency conditions such as fires and earthquakes. HDVGE could also serve as a new means of obtaining observational data about individual and group behavior in support of human geography research.

Bio-flex obtained from pyrolysis of biomass as fuel; Bio-flex obtido da pirolise de biomassa como combustivel

Energy Technology Data Exchange (ETDEWEB)

Mesa Perez, Juan Miguel; Viltre Rodriguez, Roberto Alfonso; Marin Mesa, Henry Ramon [Bioware Tecnologia, Campinas, SP (Brazil); Rocha, Jose Dilcio [Universidade Estadual de Campinas (NIPE/UNICAMP), SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico; Samaniego, Manuel Raul Pelaez [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Planejamento de Sistemas Energeticos; Cortez, Luis Augusto Barbosa [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola

2006-07-01

This paper describes the BIOWARE experience in the bio fuel production from biomass residues. Fast pyrolysis of a mixture of sugar cane trash and elephant grass carried out in a fluidized bed reactor with capacity of 200 kg/h dry feed (12% w/w). The co-products particulate charcoal, acid extract, and bio-oil were obtained. The fast pyrolysis pilot plant PPR-200 belonged to UNICAMP and is operated by BIOWARE personnel. This paper presents the chemical rote to bio-flex production (a kind of bio diesel from acid esterification) from pyrolytic carboxylic acids. Both ethanol and methanol were used as reactant but higher yields were found with methanol. (author)

Mixtures of rubber tyre and plastic wastes pyrolysis: A kinetic study

International Nuclear Information System (INIS)

Miranda, Miguel; Cabrita, I.; Pinto, Filomena; Gulyurtlu, I.

2013-01-01

The study performed aimed at analysing possible routes for pyrolysis reaction mechanisms of polymeric materials namely RT (rubber tyre) and plastic wastes (PE (polyethylene), PP (polypropylene) and PS (polystyrene)). Consequently, and seeking sustainable transformation of waste streams into valuable chemicals and renewable liquid fuels, mixture of 30% RT, 20% PE, 30% PP and 20% PS was subjected to pyrolysis. Different kinetic models were studied using experimental data. None of the mechanisms found in literature led to a numerical adjustment and different pathways were investigated. Kinetic studies were performed aiming to evaluate direct conversions into new solid, liquid and gaseous products and if parallel reactions and/or reversible elementary steps should be included. Experiments were performed in batch system at different temperatures and reaction times. Kinetic models were evaluated and reaction pathways were proposed. Models reasonably fit experimental data, allow explaining wastes thermal degradation. Kinetic parameters were estimated for all temperatures and dependence of Ea and pre-exponential factor on temperature was evaluated. The rate constant of some reactions exhibited nonlinear temperature dependence on the logarithmic form of Arrhenius law. This fact strongly suggests that temperature has a significant effect on reaction mechanism of pyrolysis of mixtures of rubber tyre and plastic wastes. - Highlights: • Kinetic study of rubber tyre (RT) and different plastic wastes (PE, PP and PS) was performed in batch reactor. • Definition of possible pathways taken into account for the formation of final products. • Kinetic parameters were estimated. • The effect of reaction temperature and reaction time on liquid composition was performed

Pyrolysis in Groningen, Netherlands. Feasibility study on a transition coalition

International Nuclear Information System (INIS)

Siemons, R.V.

2005-01-01

Results of a study on the technical, economical and financial feasibility of a pyrolysis factory for the processing and energetic application of biomass wastes in the Dutch province Groningen are presented and discussed. Also, attention is paid to the implementation of the planned pyrolysis factory in one or more transition programmes. [nl

Chemical yields from low-temperature pyrolysis of CCA-treated wood

Science.gov (United States)

Qirong Fu; Dimitris Argyropolous; Lucian Lucia; David Tilotta; Stan Lebow

2009-01-01

Low-temperature pyrolysis offers a feasible option for wood-waste management and the recovery of a variety of useful chemicals. The effect of chromated copper arsenate (CCA) wood preservative on the yield and composition of various pyrolysis products was investigated in the present research. A novel quantitative 31P nuclear magnetic resonance (...

Pyrolysis of Softwood Carbohydrates in a Fluidized Bed Reactor

Directory of Open Access Journals (Sweden)

Dmitry Yu. Murzin

2008-09-01

Full Text Available In the present work pyrolysis of pure pine wood and softwood carbohydrates, namely cellulose and galactoglucomannan (the major hemicellulose in coniferous wood, was conducted in a batch mode operated fluidized bed reactor. Temperature ramping (5°C/min was applied to the heating until a reactor temperature of 460 °C was reached. Thereafter the temperature was kept until the release of non-condensable gases stopped. The different raw materials gave significantly different bio-oils. Levoglucosan was the dominant product in the cellulose pyrolysis oil. Acetic acid was found in the highest concentrations in both the galactoglucomannan and in the pine wood pyrolysis oils. Acetic acid is most likely formed by removal of O-acetyl groups from mannose units present in GGM structure.

Experimental study of co-pyrolysis of polyethylene/sawdust mixtures

Directory of Open Access Journals (Sweden)

Berrueco Cesar

2004-01-01

Full Text Available A study of the behavior of the thermal decomposition of mixtures of biomass and thermoplastics, such as polyethylene, is of interest for processes for the thermal recovery of industrial and urban wastes such as pyrolysis or gasification. No solid residue is formed during the thermal degradation of pure polyethylene. However, the addition of biomass, which generates char can vary the product distribution and increase the heating value of the gas obtained. A study of the thermal degradation of pine sawdust, polyethylene and mixtures of polyethylene and pine sawdust has been carried out in a fluidized bed reactor. Experiments were carried out at five different temperatures: 640, 685, 730, 780, and 850 ºC. The yields and composition of the derived oil, wax, and gas were determined. The addition of polyethylene increases the gas production and decreases the production of waxes and liquids for the different temperatures tested. The main gases produced from the co-pyrolysis process were, at low temperatures, carbon monoxide ethylene, carbon dioxide, propylene, butadiene, methane and pentadiene while at high temperatures the gas composition changed drastically, the main components being carbon monoxide (more than 33 wt.%, ethylene, methane benzene and hydrogen. The analysis of the liquid fraction shows a decrease of the concentration of oxygenated and aliphatic compounds.

Pyrolysis and oxy-fuel combustion characteristics and kinetics of petrochemical wastewater sludge using thermogravimetric analysis.

Science.gov (United States)

Chen, Jianbiao; Mu, Lin; Cai, Jingcheng; Yao, Pikai; Song, Xigeng; Yin, Hongchao; Li, Aimin

2015-12-01

The pyrolysis and oxy-fuel combustion characteristics of petrochemical wastewater sludge (PS) were studied in air (O2/N2) and oxy-fuel (O2/CO2) atmospheres using non-isothermal thermogravimetric analysis (TGA). Pyrolysis experiments showed that the weight loss profiles were almost similar up to 1050K in both N2 and CO2 atmospheres, while further weight loss took place in CO2 atmosphere at higher temperatures due to char-CO2 gasification. Compared with 20%O2/80%N2, the drying and devolatilization stage of PS were delayed in 20%O2/80%CO2 due to the differences in properties of the diluting gases. In oxy-fuel combustion experiments, with O2 concentration increasing, characteristic temperatures decreased, while characteristic combustion rates and combustion performance indexes increased. Kinetic analysis of PS decomposition under various atmospheres was performed using Coats-Redfern approach. The results indicated that, with O2 concentration increasing, the activation energies of Step 1 almost kept constant, while the values of subsequent three steps increased. Copyright © 2015 Elsevier Ltd. All rights reserved.

Kinetic study and syngas production from pyrolysis of forestry waste

International Nuclear Information System (INIS)

Hu, Mian; Wang, Xun; Chen, Jian; Yang, Ping; Liu, Cuixia; Xiao, Bo; Guo, Dabin

2017-01-01

Highlights: • Pyrolysis process can be divided into three stages using differential DTG method. • A modified discrete DAEM model fitted experimental data well. • Fe/biochar catalyst showed a good performance on catalytic reforming process. - Abstract: Kinetic study and syngas production from pyrolysis of forestry waste (pine sawdust (PS)) were investigated using a thermogravimetric analyzer (TGA) and a fixed-bed reactor, respectively. In TGA, it was found that the pyrolysis of PS could be divided into three stages and stage II was the major mass reduction stage with mass loss of 73–74%. The discrete distributed activation energy model (DAEM) with discrete 200 first-order reactions was introduced to study the pyrolysis kinetic. The results indicated that the DAEM with 200 first-order reactions could approximate the pyrolysis process with an excellent fit between experimental and calculated data. The apparent activation energies of PS ranged from 147.86 kJ·mol −1 to 395.76 kJ·mol −1 , with corresponding pre-exponential factors of 8.30 × 10 13 s −1 to 3.11 × 10 25 s −1 . In the fixed-bed reactor, char supported iron catalyst was prepared for tar cracking. Compared with no catalyst which the gas yield and tar yield were 0.58 N m 3 /kg biomass and 201.23 g/kg biomass, the gas yield was markedly increased to 1.02 N m 3 /kg biomass and the tar yield was decreased to only 26.37 g/kg biomass in the presence of char supported iron catalyst. These results indicated that char supported iron catalyst could potentially be used to catalytically decompose tar molecules in syngas generated via biomass pyrolysis.

Catalytic Fast Pyrolysis: A Review

Directory of Open Access Journals (Sweden)

Theodore Dickerson

2013-01-01

Full Text Available Catalytic pyrolysis is a promising thermochemical conversion route for lignocellulosic biomass that produces chemicals and fuels compatible with current, petrochemical infrastructure. Catalytic modifications to pyrolysis bio-oils are geared towards the elimination and substitution of oxygen and oxygen-containing functionalities in addition to increasing the hydrogen to carbon ratio of the final products. Recent progress has focused on both hydrodeoxygenation and hydrogenation of bio-oil using a variety of metal catalysts and the production of aromatics from bio-oil using cracking zeolites. Research is currently focused on developing multi-functional catalysts used in situ that benefit from the advantages of both hydrodeoxygenation and zeolite cracking. Development of robust, highly selective catalysts will help achieve the goal of producing drop-in fuels and petrochemical commodities from wood and other lignocellulosic biomass streams. The current paper will examine these developments by means of a review of existing literature.

Kinetic Study of the Catalytic Pyrolysis of Oil-Containing Waste

Directory of Open Access Journals (Sweden)

Kirill Chalov

2016-10-01

Full Text Available Basing on the experimental data the optimal parameters of the pyrolysis of heavy and residual hydrocarbons of oil were defined as follows: temperature of 500 °С; catalyst  of CoCl2 with the catalyst loading 5% (wt. of the substrate weight. Under the optimal conditions the kinetic investigation of the pyrolysis process was carried out using the thermogravimetric method. According to the investigation, it was found that the activation energy of the catalytic pyrolysis of oil-containing waste decreased by 20-30 kJ/mol in comparison to non-catalytic process. Copyright © 2016 BCREC GROUP. All rights reserved Received: 13th July 2015; Revised: 25th March 2016; Accepted: 1st April 2016 How to Cite: Chalov, K., Lugovoy, Y., Kosivtsov, Y., Sulman, M., Sulman, E., Matveeva, V., Stepacheva, A. (2016. Kinetic Study of the Catalytic Pyrolysis of Oil-Containing Waste. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (3: 330-338 (doi:10.9767/bcrec.11.3.572.330-338 Permalink/DOI: http://doi.org/10.9767/bcrec.11.3.572.330-338

Structural investigations of neuromelanin by pyrolysis-gas chromatography/mass spectrometry

International Nuclear Information System (INIS)

Dzierzega-Lecznar, A.; Kurkiewicz, S.; Stepien, K.; Chodurek, E.; Riederer, P.; Gerlach, M.

2006-01-01

Pyrolysis combined with gas chromatography and mass spectrometry (Py-GC/MS) was applied for structural investigations of the human substantia nigra neuromelanin. Using synthetic neuromelanins, we have demonstrated that Py-GC/MS is suitable for identification and differentiation of both eumelanin (dopamine-derived) and pheomelanin (cysteinyldopamine-derived) component of the pigment. Structural information on melanin monomers was inferred from their pyrolytic markers. When the human neuromelanin was subjected to pyrolysis, none of the heterocyclic, sulfur-containing markers of pheomelanin component was detected among the thermal degradation products. We have concluded that nigral pigment isolated from normal brain tissue does not contain benzothiazine-type monomers, and that cysteinyldopamine-originated units may be incorporated into the polymer in uncyclized form. The most abundant pyrolysis product was identified as limonene, which indicates that nigral pigment is tightly associated with an isoprenoid-type compound. Pyrolysis in the presence of the methylating reagent allowed identification of high levels of saturated and monounsaturated straight-chain C14-C18 fatty acid species chemically bound to the pigment macromolecule. (author)

Pyrolysis characteristics and kinetics of aquatic biomass using thermogravimetric analyzer.

Science.gov (United States)

Wu, Kejing; Liu, Ji; Wu, Yulong; Chen, Yu; Li, Qinghai; Xiao, Xin; Yang, Mingde

2014-07-01

The differences in pyrolysis process of three species of aquatic biomass (microalgae, macroalgae and duckweed) were investigated by thermogravimetric analysis (TGA). Three stages were observed during the pyrolysis process and the main decomposition stage could be divided further into three zones. The pyrolysis characteristics of various biomasses were different at each zone, which could be attributed to the differences in their components. A stepwise procedure based on iso-conversional and master-plots methods was used for the kinetic and mechanism analysis of the main decomposition stage. The calculation results based on the kinetic model was in good agreement with the experimental data of weight loss, and each biomass had an increasing activation energy of 118.35-156.13 kJ/mol, 171.85-186.46 kJ/mol and 258.51-268.71 kJ/mol in zone 1, 2 and 3, respectively. This study compares the pyrolysis behavior of various aquatic biomasses and provides basis for further applications of the biomass thermochemical conversion. Copyright © 2014. Published by Elsevier Ltd.

The IPRP (Integrated Pyrolysis Regenerated Plant) technology: From concept to demonstration

International Nuclear Information System (INIS)

D’Alessandro, Bruno; D’Amico, Michele; Desideri, Umberto; Fantozzi, Francesco

2013-01-01

Highlights: ► IPRP technology development for distributed conversion of biomass and wastes. ► IPRP demonstrative unit combines a rotary kiln pyrolyzer to a 80 kWe microturbine. ► Main performances and critical issues are pointed out for different residual fuels. -- Abstract: The concept of integrated pyrolysis regenerated plant (IPRP) is based on a Gas Turbine (GT) fuelled by pyrogas produced in a rotary kiln slow pyrolysis reactor, where waste heat from GT is used to sustain the pyrolysis process. The IPRP plant provides a unique solution for microscale (below 250 kW) power plants, opening a new and competitive possibility for distributed biomass or wastes to energy conversion systems. The paper summarizes the state of art of the IPRP technology, from preliminary numerical simulation to pilot plant facility, including some new available data on pyrolysis gas from laboratory and pilot plants.

Preparation, characterization and environmental/electrochemical energy storage testing of low-cost biochar from natural chitin obtained via pyrolysis at mild conditions

Science.gov (United States)

Magnacca, Giuliana; Guerretta, Federico; Vizintin, Alen; Benzi, Paola; Valsania, Maria C.; Nisticò, Roberto

2018-01-01

Chitin (a biopolymer obtained from shellfish industry) was used as precursor for the production of biochars obtained via pyrolysis treatments performed at mild conditions (in the 290-540 °C range). Biochars were physicochemical characterized in order to evaluate the pyrolysis-induced effects in terms of both functional groups and material structure. Moreover, such carbonaceous materials were tested as adsorbent substrates for the removal of target molecules from aqueous environment as well as in solid-gas experiments, to measure the adsorption capacities and selectivity toward CO2. Lastly, biochars were also investigated as possible cathode materials in sustainable and low-cost electrochemical energy storage devices, such as lithium-sulphur (Li-S) batteries. Interestingly, experimental results evidenced that such chitin-derived biochars obtained via pyrolysis at mild conditions are sustainable, low-cost and easy scalable alternative materials suitable for both environmental and energetic applications.

Potential pyrolysis pathway assessment for microalgae-based aviation fuel based on energy conversion efficiency and life cycle

International Nuclear Information System (INIS)

Guo, Fang; Wang, Xin; Yang, Xiaoyi

2017-01-01

Highlights: • High lipid content in microalgae increases energy conversion efficiency. • Indirect pathway has the highest mass ratio, energy ratio and energy efficiency. • The Isochrysis indirect pathway produces most kerosene component precursor. • The Isochrysis indirect pyrolysis pathway shows the best performance in LCA. - Abstract: Although the research of microalgae pyrolysis has been conducted for many years, there is a lack of investigations on energy efficiency and life cycle assessment. In this study, we investigated the biocrude yield and energy efficiency of direct pyrolysis, microalgae residue pyrolysis after lipid extraction (indirect pyrolysis), and different microalgae co-pyrolysis. This research also investigated the life cycle assessment of the three different pyrolysis pathways. A system boundary of Well-to-Wake (WTWa) was defined and included sub-process models, such as feedstock production, fuel production and pump-to-wheels (PTW) stages. The pathway of Isochrysis indirect pyrolysis shows the best performance in the mass ratio and energy ratio, produces the most kerosene component precursor, has the lowest WTWa total energy input, fossil fuel consumption and greenhouse gas emissions, and resultes in the best energy efficiency. All the evidence indicates that Isochrysis R2 pathway is a potential and optimal pyrolysis pathway to liquid biofuels. The mass ratio of pyrolysis biocrude is shown to be the decisive factor for different microalgae species. The sensitivity analysis results also indicates that the life cycle indicators are particularly sensitive to the mass ratio of pyrolysis biocrude for microalgae-based hydrotreated pyrolysis aviation fuel.

Co-pyrolysis of swine manure with agricultural plastic waste: laboratory-scale study.

Science.gov (United States)

Ro, Kyoung S; Hunt, Patrick G; Jackson, Michael A; Compton, David L; Yates, Scott R; Cantrell, Keri; Chang, SeChin

2014-08-01

Manure-derived biochar is the solid product resulting from pyrolysis of animal manures. It has considerable potential both to improve soil quality with high levels of nutrients and to reduce contaminants in water and soil. However, the combustible gas produced from manure pyrolysis generally does not provide enough energy to sustain the pyrolysis process. Supplementing this process may be achieved with spent agricultural plastic films; these feedstocks have large amounts of available energy. Plastic films are often used in soil fumigation. They are usually disposed in landfills, which is wasteful, expensive, and environmentally unsustainable. The objective of this work was to investigate both the energetics of co-pyrolyzing swine solids with spent plastic mulch films (SPM) and the characteristics of its gas, liquid, and solid byproducts. The heating value of the product gas from co-pyrolysis was found to be much higher than that of natural gas; furthermore, the gas had no detectable toxic fumigants. Energetically, sustaining pyrolysis of the swine solids through the energy of the product gas could be achieved by co-pyrolyzing dewatered swine solids (25%m/m) with just 10% SPM. If more than 10% SPM is used, the co-pyrolysis would generate surplus energy which could be used for power generation. Biochars produced from co-pyrolyzing SPM and swine solid were similar to swine solid alone based on the surface area and the (1)H NMR spectra. The results of this study demonstrated the potential of using pyrolysis technology to manage two prominent agricultural waste streams (SPM and swine solids) while producing value-added biochar and a power source that could be used for local farm operations. Published by Elsevier Ltd.

Crime and Young Men: The Role of Arrest, Criminal Experience, and Heterogeneity

OpenAIRE

Susumu Imai; Hajime Katayama; Kala Krishna

2006-01-01

Using National Youth Survey (NYS) data, we examine the relationship of current criminal activity and past arrests using an ordered probit model with unobserved heterogeneity. Past arrests raise current criminal activity only for the non-criminal type, while past criminal experience raises current criminal activity for both types. Also, the age crime profile peaks at age 18 for non-criminal type individuals, but for criminal type individuals, it continues to rise with age. Past research indica...

Experimental and Chemical Kinetic Modeling Study of Dimethylcyclohexane Oxidation and Pyrolysis

KAUST Repository

Eldeeb, Mazen A.

2016-08-30

A combined experimental and chemical kinetic modeling study of the high-temperature ignition and pyrolysis of 1,3-dimethylcyclohexane (13DMCH) is presented. Ignition delay times are measured behind reflected shock waves over a temperature range of 1049–1544 K and pressures of 3.0–12 atm. Pyrolysis is investigated at average pressures of 4.0 atm at temperatures of 1238, 1302, and 1406 K. By means of mid-infrared direct laser absorption at 3.39 μm, fuel concentration time histories are measured under ignition and pyrolytic conditions. A detailed chemical kinetic model for 13DMCH combustion is developed. Ignition measurements show that the ignition delay times of 13DMCH are longer than those of its isomer, ethylcyclohexane. The proposed chemical kinetic model predicts reasonably well the effects of equivalence ratio and pressure, with overall good agreement between predicted and measured ignition delay times, except at low dilution levels and high pressures. Simulated fuel concentration profiles agree reasonably well with the measured profiles, and both highlight the influence of pyrolysis on the overall ignition kinetics at high temperatures. Sensitivity and reaction pathway analyses provide further insight into the kinetic processes controlling ignition and pyrolysis. The work contributes toward improved understanding and modeling of the oxidation and pyrolysis kinetics of cycloalkanes.

Solar Assisted Fast Pyrolysis: A Novel Approach of Renewable Energy Production

Directory of Open Access Journals (Sweden)

Mohammad U. H. Joardder

2014-01-01

Full Text Available Biofuel produced by fast pyrolysis from biomass is a promising candidate. The heart of the system is a reactor which is directly or indirectly heated to approximately 500°C by exhaust gases from a combustor that burns pyrolysis gas and some of the by-product char. In most of the cases, external biomass heater is used as heating source of the system while internal electrical heating is recently implemented as source of reactor heating. However, this heating system causes biomass or other conventional forms of fuel consumption to produce renewable energy and contributes to environmental pollution. In order to overcome these, the feasibility of incorporating solar energy with fast pyrolysis has been investigated. The main advantages of solar reactor heating include renewable source of energy, comparatively simpler devices, and no environmental pollution. A lab scale pyrolysis setup has been examined along with 1.2 m diameter parabolic reflector concentrator that provides hot exhaust gas up to 162°C. The study shows that about 32.4% carbon dioxide (CO2 emissions and almost one-third portion of fuel cost are reduced by incorporating solar heating system. Successful implementation of this proposed solar assisted pyrolysis would open a prospective window of renewable energy.

Product Characterization and Kinetics of Biomass Pyrolysis in a Three-Zone Free-Fall Reactor

Directory of Open Access Journals (Sweden)

Natthaya Punsuwan

2014-01-01

Full Text Available Pyrolysis of biomass including palm shell, palm kernel, and cassava pulp residue was studied in a laboratory free-fall reactor with three separated hot zones. The effects of pyrolysis temperature (250–1050°C and particle size (0.18–1.55 mm on the distribution and properties of pyrolysis products were investigated. A higher pyrolysis temperature and smaller particle size increased the gas yield but decreased the char yield. Cassava pulp residue gave more volatiles and less char than those of palm kernel and palm shell. The derived solid product (char gave a high calorific value of 29.87 MJ/kg and a reasonably high BET surface area of 200 m2/g. The biooil from palm shell is less attractive to use as a direct fuel, due to its high water contents, low calorific value, and high acidity. On gas composition, carbon monoxide was the dominant component in the gas product. A pyrolysis model for biomass pyrolysis in the free-fall reactor was developed, based on solving the proposed two-parallel reactions kinetic model and equations of particle motion, which gave excellent prediction of char yields for all biomass precursors under all pyrolysis conditions studied.

Evaluation of Integrated Time-Temperature Effect in Pyrolysis Process of Historically Contaminated Soils with Cadmium (Cd and Lead (Pb

Directory of Open Access Journals (Sweden)

Bulmău C

2013-04-01

Full Text Available It is already known that heavy metals pollution causes important concern to human and ecosystem health. Heavy metals in soils at the European level represents 37.3% between main contaminates affecting soils (EEA, 2007. This paper illustrates results obtained in the framework of laboratory experiments concerning the evaluation of integrated time-temperature effect in pyrolysis process applied to contaminated soil by two different ways: it is about heavy metals historically contaminated soil from one of the most polluted areas within Romania, and artificially contaminated with PCB-containing transformer oil. In particular, the authors focused on a recent evaluation of pyrolysis efficiency on removing lead (Pb and cadmium (Cd from the contaminated soil. The experimental study evaluated two important parameters related to the studied remediation methodology: thermal process temperature and the retention time in reactor of the contaminated soils. The remediation treatments were performed in a rotary kiln reactor, taking into account three process temperatures (400°C, 600°C and 800°C and two retention times: 30 min. and 60 min. Completed analyses have focused on pyrolysis solids and gas products. Consequently, both ash and gas obtained after pyrolysis process were subjected to chemical analyses.

Comparative study on pyrolysis of lignocellulosic and algal biomass using a thermogravimetric and a fixed-bed reactor.

Science.gov (United States)

Yuan, Ting; Tahmasebi, Arash; Yu, Jianglong

2015-01-01

Pyrolysis characteristics of four algal and lignocellulosic biomass samples were studied by using a thermogravimetric analyzer (TGA) and a fixed-bed reactor. The effects of pyrolysis temperature and biomass type on the yield and composition of pyrolysis products were investigated. The average activation energy for pyrolysis of biomass samples by FWO and KAS methods in this study were in the range of 211.09-291.19kJ/mol. CO2 was the main gas component in the early stage of pyrolysis, whereas H2 and CH4 concentrations increased with increasing pyrolysis temperature. Bio-oil from Chlorellavulgaris showed higher content of nitrogen containing compounds compared to lignocellulosic biomass. The concentration of aromatic organic compounds such as phenol and its derivatives were increased with increasing pyrolysis temperature up to 700°C. FTIR analysis results showed that with increasing pyrolysis temperature, the concentration of OH, CH, CO, OCH3, and CO functional groups in char decreased sharply. Copyright © 2014 Elsevier Ltd. All rights reserved.

Economic assessment of flash co-pyrolysis of short rotation coppice and biopolymer waste streams.

Science.gov (United States)

Kuppens, T; Cornelissen, T; Carleer, R; Yperman, J; Schreurs, S; Jans, M; Thewys, T

2010-12-01

The disposal problem associated with phytoextraction of farmland polluted with heavy metals by means of willow requires a biomass conversion technique which meets both ecological and economical needs. Combustion and gasification of willow require special and costly flue gas treatment to avoid re-emission of the metals in the atmosphere, whereas flash pyrolysis mainly results in the production of (almost) metal free bio-oil with a relatively high water content. Flash co-pyrolysis of biomass and waste of biopolymers synergistically improves the characteristics of the pyrolysis process: e.g. reduction of the water content of the bio-oil, more bio-oil and less char production and an increase of the HHV of the oil. This research paper investigates the economic consequences of the synergistic effects of flash co-pyrolysis of 1:1 w/w ratio blends of willow and different biopolymer waste streams via cost-benefit analysis and Monte Carlo simulations taking into account uncertainties. In all cases economic opportunities of flash co-pyrolysis of biomass with biopolymer waste are improved compared to flash pyrolysis of pure willow. Of all the biopolymers under investigation, polyhydroxybutyrate (PHB) is the most promising, followed by Eastar, Biopearls, potato starch, polylactic acid (PLA), corn starch and Solanyl in order of decreasing profits. Taking into account uncertainties, flash co-pyrolysis is expected to be cheaper than composting biopolymer waste streams, except for corn starch. If uncertainty increases, composting also becomes more interesting than flash co-pyrolysis for waste of Solanyl. If the investment expenditure is 15% higher in practice than estimated, the preference for flash co-pyrolysis compared to composting biopolymer waste becomes less clear. Only when the system of green current certificates is dismissed, composting clearly is a much cheaper processing technique for disposing of biopolymer waste. Copyright © 2010 Elsevier Ltd. All rights reserved.

Kinetic study of the catalytic pyrolysis of elephant grass using Ti-MCM-41

Energy Technology Data Exchange (ETDEWEB)

Fontes, Maria do Socorro Braga; Melo, Dulce Maria de Araujo; Rodrigues, Glicelia, E-mail: socorro.fontes@yahoo.com.br [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Barros, Joana Maria de Farias [Universidade Federal de Campina Grande (UFCG), Cuite, PB (Brazil). Dept. de Quimica; Braga, Renata Martins [Universidade Federal da Paraiba (UFPB/CEAR/DEER), Joao Pessoa, PB (Brazil). Centro de Energias Alternativas e Renovaveis. Dept. de Engenharia de Energia Renovaveis

2014-08-15

This work aimed to study the kinetics of thermal and catalytic pyrolysis using Ti-MCM-41 as catalyst in order to assess the catalytic pyrolysis efficiency compared to thermal pyrolysis of elephant grass. Ti-MCM-41 molecular sieve was synthesized by hydrothermal method from hydrogel with the following molar composition: 1.00 CTMABr: 4.00 SiO{sub 2}:X TiO{sub 2}: 1 + X Na{sub 2}O: 200.00 H{sub 2}O, which structure template used was cetyltrimethylammonium bromide (CTMABr). The materials synthesized were characterized by X-ray diffraction, IR spectroscopy, thermogravimetric analysis and specific area by the BET method, for subsequent application in the biomass pyrolysis process. The kinetic models proposed by Vyazovkin and Flynn-Wall were used to determine the apparent activation energy involved in the thermal and catalytic pyrolysis of elephant grass and the results showed that the catalyst used was effective in reducing the apparent activation energy involved in the thermal decomposition of elephant grass. (author)

Factors affecting the yield of bio-oil from the pyrolysis of coconut shell.

Science.gov (United States)

Gao, Yun; Yang, Yi; Qin, Zhanbin; Sun, Yi

2016-01-01

Coconut is a high-quality agricultural product of the Asia-Pacific region. In this paper, coconut shell which mainly composed of cellulose, hemicellulose, lignin was used as a raw material for coconut shell oil from coconut shell pyrolysis. The influence of the pyrolysis temperature, heating rate and particle size on coconut oil yield was investigated, and the effect of heating rate on coconut oil components was discussed. Experimental results show that the maximum oil yield of 75.74 wt% (including water) were obtained under the conditions that the final pyrolysis temperature 575 °C, heating rate 20 °C/min, coconut shell diameter about 5 mm. Thermal gravimetric analysis was used and it can be seen that coconut shell pyrolysis process can be divided into three stages: water loss, pyrolysis and pyrocondensation. The main components of coconut-shell oil are water (about 50 wt%), aromatic, phenolic, acid, ketone and ether containing compounds.

Effects of biopretreatment on pyrolysis behaviors of corn stalk by methanogen.

Science.gov (United States)

Wang, Tipeng; Ye, Xiaoning; Yin, Jun; Lu, Qiang; Zheng, Zongming; Dong, Changqing

2014-07-01

The study investigated the effects of methanogen pretreatment on pyrolysis behaviors of corn stalk (CS) by using Py-GC/MS analysis and thermogravimetric analysis. Results indicated that biopretreatment changed considerably the pyrolysis behaviors of CS from four weight loss stages to two weight loss stages. Increasing biopretreatment time from 5 days to 25 days enhanced the kinds and contents of chemicals in volatile products. In pyrolysis products, the contents of sugars, linear ketones and furans decreased from 1.43%, 12.60% and 7.38% to 1.25%, 10.22% and 3.25%, respectively, and the contents of phenols increased from 15.08% to 27.84%. The most content change from 6.83% to 13.63% indicated that methanogen pretreatment improved the pyrolysis selectivity of CS to product the 4-VP, but it was disadvantageous to 5-hydroxymethyl furfural, levoglucose and furfural. The changes of chemical compositions and structure of CS after biopretreatment were the main reason of the differences. Copyright © 2014 Elsevier Ltd. All rights reserved.

Correlation Between Pyrolysis Atmosphere and Carbon Molecular Sieve Membrane Performance Properties

KAUST Repository

Kiyono, Mayumi; Koros, William J.; Williams, Paul J.

2011-01-01

Carbon molecular sieve (CMS) membranes have attractive separation performance properties, greatly exceeding an "upper bound" trade-off curve of polymeric membrane performance. CMS membranes are prepared by pyrolyzing polymers, well above their glass transition temperatures. Multiple factors, such as polymer precursor and pyrolysis protocol, are known to affect the separation performance. In this study, a correlation observed between pyrolysis atmosphere and CMS separation performance properties is discussed. Specifically, oxygen exposure during the pyrolysis process is the focus. The theory and details of the oxygen exposure and development of a new CMS preparation method using oxygen as a "dopant" will be described with a strong correlation observed with separation performance for CMS membranes prepared with various polymer precursors. In addition, study of possible mass transfer limitations on the oxygen "doping" process will be described to clarify the basis for the equilibrium-based interpretation of doping data. The method is also explored by changing the pyrolysis temperature. © 2011 Elsevier B.V.

Pyrolysis characteristics and kinetics of microalgae via thermogravimetric analysis (TGA): A state-of-the-art review.

Science.gov (United States)

Bach, Quang-Vu; Chen, Wei-Hsin

2017-12-01

Pyrolysis is a promising route for biofuels production from microalgae at moderate temperatures (400-600°C) in an inert atmosphere. Depending on the operating conditions, pyrolysis can produce biochar and/or bio-oil. In practice, knowledge for thermal decomposition characteristics and kinetics of microalgae during pyrolysis is essential for pyrolyzer design and pyrolysis optimization. Recently, the pyrolysis kinetics of microalgae has become a crucial topic and received increasing interest from researchers. Thermogravimetric analysis (TGA) has been employed as a proven technique for studying microalgae pyrolysis in a kinetic control regime. In addition, a number of kinetic models have been applied to process the TGA data for kinetic evaluation and parameters estimation. This paper aims to provide a state-of-the art review on recent research activities in pyrolysis characteristics and kinetics of various microalgae. Common kinetic models predicting the thermal degradation of microalgae are examined and their pros and cons are illustrated. Copyright © 2017 Elsevier Ltd. All rights reserved.

Studies on liquefaction and pyrolysis of peat and biomass at KTH

International Nuclear Information System (INIS)

Bjoernbom, E.; Sjoestrom, K.; Hoernel, C.; Zanzi, R.; Bjoernbom, P.

1996-01-01

A brief review of the study on thermochemical conversion of solid fuels is done. The study have been performed in the Royal Institute of Technology, Stockholm, since the outbreak of energy crisis in the seventies. The main problems connected with utilisation of peat for energy are: 90% moisture content in the deposits and 35-40% oxygen content in the dry substance. Simultaneous dewatering and liquefaction of peat have been achieved by the Bjoerbom method. The wet peat has been treated with CO and H 2 O without preliminary drying, using water as a medium agent. After treatment water has been phase-separated from the heavy oil product. Another approach is de-oxygenation of peat prior to liquefaction. A significant part of oxygen in peat and biomass can be removed by thermal decomposition of the fuels prior to liquefaction and removal of carbon dioxide and water from the organic matter in them. The products obtained after de-oxygenation demand low consumption of external hydrogenation agent because they are rich in hydrogen. Some criteria for selection of peat as a raw material for liquefaction are given. The equipment and experimental procedure for pyrolysis of peat and biomass are described. A free fall tubular reactor with max operating pressure of 5 MPa and temperature of 1100 o C has been used. The effect of treatment conditions under the rapid pyrolysis in the free fall reactor on the yield and the reactivity of char obtained after the final pyrolysis is shown. Peat and wood are transformed into pyrolysis products for less than 1 second; 35-50% of the moisture- and ash-free peat and 70% of the wood have been converted into gaseous products.The char obtained in the rapid pyrolysis contains a fraction which can be further de-volatilized by slow pyrolysis for a few minutes - time much longer than the time for formation of primary products. High reactivity of char is favoured by lower pyrolysis temperature, shorter residence time and larger particle size of the fuel

Heterogeneity in pineapple fruit quality results from plant heterogeneity at flower induction

NARCIS (Netherlands)

Fassinou Hotegni, V.N.; Lommen, W.J.M.; Agbossou, E.K.; Struik, P.C.

2014-01-01

Heterogeneity in fruit quality constitutes a major constraint in agri-food chains. In this paper the sources of the heterogeneity in pineapple in the field were studied in four experiments in commercial pineapple fields. The aims were to determine (a) whether differences in pineapple fruit quality

Total recovery of nitrogen and phosphorus from three wetland plants by fast pyrolysis technology.

Science.gov (United States)

Liu, Wu-Jun; Zeng, Fan-Xin; Jiang, Hong; Yu, Han-Qing

2011-02-01

Fast pyrolysis of three wetland plants (Alligator weed, Oenanthe javanica and Typha angustifolia) in a vertical drop fixed bed reactor was investigated in this study. The experiments were carried out at different pyrolysis temperatures, and the maximum bio-oil yields achieved were 42.3%, 40.2% and 43.6% for Alligator weed, Oenanthe javanica and Typha angustifolia, respectively. The elemental composition of the bio-oil and char were analyzed, and the results show that a low temperature was appropriate for the nitrogen and phosphorus enrichment in char. GC-MS analysis shows that nitrogenous compounds, phenols and oxygenates were the main categories in the bio-oil. A series of leaching tests were carried out to examine the recovery of the nitrogen and phosphorus in the char, and the results indicate that significant fractions of nitrogen and phosphorus could be recovered by leaching process. Copyright © 2010 Elsevier Ltd. All rights reserved.

Controllable production of liquid and solid biofuels by doping-free, microwave-assisted, pressurised pyrolysis of hemicellulose

International Nuclear Information System (INIS)

Li, T.; Remón, J.; Shuttleworth, P.S.; Jiang, Z.; Fan, J.; Clark, J.H.; Budarin, V.L.

2017-01-01

Highlights: • Microwave pyrolysis of xylan in the absence of any external microwave absorber. • High energy-efficient and controllable production of biochar and bio-oil from xylan. • Water in liquid phase is needed for fast microwave pyrolysis. • Production of bio-oil and bio-char with HHVs 52% and 19% greater than that of xylan. - Abstract: Batch, pressurised microwave-assisted pyrolysis of hemicellulose in the absence of any external microwave absorber was found to be a promising route for the production of bio-based chemicals and biofuels. The experiments were conducted in a 10 mL batch reactor using a fixed power of 200 W employing different initial masses of xylan (0.1–0.7 g) for a maximum time, temperature and pressure of 10 min, 250 °C and 200 psi, respectively. The gas, bio-oil and solid (char) yields varied by 16–40%, 2–21% and 40–82%, respectively. Char production is preferential using a low amount of xylan (<0.25 g), while bio-oil production is favoured using a high amount of xylan (0.25–0.7 g). The effect of the sample mass is accounted for by the different physical state of the volatiles released during pyrolysis depending on the pressure attained during the experiment. This permits the process to be easily customised for the selective production of liquid (bio-oil) or solid (bio-char). Regarding the bio-oil, it is composed of a mixture of platform chemicals such as aldehydes, alkenes, phenols, polyaromatic hydrocarbons (PAHC), cyclic ketones and furans, with the composition varying depending on the initial mass of xylan. The char had a higher proportion of C together with a lower proportion of O than the original feedstock. Energy efficiencies of 100 and 26% were achieved for char and bio-oil production, respectively; thus leading to an increase in the HHV of the products (with respect to the original feedstock) of 52% for char and 19% for bio-oil.

Use of palm oil decanter cake as a new substrate for the production of bio-oil by vacuum pyrolysis

International Nuclear Information System (INIS)

Dewayanto, Nugroho; Isha, Ruzinah; Nordin, Mohd Ridzuan

2014-01-01

Highlights: • Vacuum pyrolysis has been employed to produce bio-oil from palm oil waste. • Effect of the pyrolysis temperature was investigated in this study. • Bio-oil properties of cellulosic and oily based material were determined. • Bio-oil from decanter cake has potential to be used as fuel. - Abstract: The present study was carried out to investigate the potential of palm oil decanter cake (PDC) for bio-oil production at various temperatures by vacuum pyrolysis. PDC was first dried in oven at 105 °C for 24 h to remove moisture and ground to particle size of 0.85–2 mm. Pyrolysis experiments were carried out at 400, 450, 500, 550 and 600 °C, with heating rate of 15 °C/min. The highest yield of bio-oil (22.12 wt%) was obtained at pyrolysis temperature of 500 °C. The chemical characterization of bio-oil was studied using 1 H NMR, FTIR, CHNS analyzer and GC–MS. The other properties like pH, calorific value and thermal volatilization were also determined. The pH value recorded to be 6.38, which is found to be higher as compared to other bio-oils. The calorific value of PDC bio-oil found to be 36.79 MJ/kg, which is slightly lower than that of conventional liquid fuel such as gasoline and diesel fuel. However, the bio-oil obtained from PDC has better fuel characteristics than that of bio-oil derived from palm kernel shell (PKS)

Performance of rotary kiln reactor for the elephant grass pyrolysis.

Science.gov (United States)

De Conto, D; Silvestre, W P; Baldasso, C; Godinho, M

2016-10-01

The influence of process conditions (rotary speed/temperature) on the performance of a rotary kiln reactor for non-catalytic pyrolysis of a perennial grass (elephant grass) was investigated. The product yields, the production of non-condensable gases as well as the biochar properties were evaluated. The maximum H2 yield was close to that observed for catalytic pyrolysis processes, while the bio-oil yield was higher than reported for pyrolysis of other biomass in rotary kiln reactors. A H2/CO ratio suitable for Fischer-Tropsch synthesis (FTS) was obtained. The biochars presented an alkaline pH (above 10) and interesting contents of nutrients, as well as low electrical conductivity, indicating a high potential as soil amendment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biomass pyrolysis/gasification for product gas production: the overall investigation of parametric effects

International Nuclear Information System (INIS)

Chen, G.; Andries, J.; Luo, Z.; Spliethoff, H.

2003-01-01

The conventional biomass pyrolysis/gasification process for production of medium heating value gas for industrial or civil applications faces two disadvantages, i.e. low gas productivity and the accompanying corrosion of downstream equipment caused by the high content of tar vapour contained in the gas phase. The objective of this paper is to overcome these disadvantages, and therefore, the effects of the operating parameters on biomass pyrolysis are investigated in a laboratory setup based on the principle of keeping the heating value of the gas almost unchanged. The studied parameters include reaction temperature, residence time of volatile phase in the reactor, physico-chemical pretreatment of biomass particles, heating rate of the external heating furnace and improvement of the heat and mass transfer ability of the pyrolysis reactor. The running temperature of a separate cracking reactor and the geometrical configuration of the pyrolysis reactor are also studied. However, due to time limits, different types of catalysts are not used in this work to determine their positive influences on biomass pyrolysis behaviour. The results indicate that product gas production from biomass pyrolysis is sensitive to the operating parameters mentioned above, and the product gas heating value is high, up to 13-15 MJ/N m 3

Experimental and modeling study on pyrolysis of n-decane initiated by nitromethane

KAUST Repository

Jia, Zhenjian

2016-01-15

Initiator could accelerate the rate of hydrocarbon pyrolysis and reduce the required material temperatures for a hypersonic aircraft heat exchanger/reactor. Nitroalkanes were proposed as the effective initiator because of the lower CN bond dissociation energy. In order to investigate the initiation mechanism of nitroalkanes on hydrocarbon pyrolysis, the pyrolysis of n-decane, nitromethane and their binary mixture were carried out at 30, 150 and 760 Torr in a flow reactor with synchrotron vacuum ultraviolet photoionization mass spectrometry (SVUV-PIMS). The identified and quantified pyrolysis species include C1C2 alkanes, C2C10 alkenes, C3C6 dialkenes, C2C3 alkynes, nitrogen oxides such as NO and NO2, benzene, and radicals including CH3, C3H3, and C3H5, which shed light on the mechanism of n-decane and nitromethane pyrolysis, as well as the interactions of these two fuels. The experimental results indicate that the addition of nitromethane decreases the initial decomposition temperature of n-decane, and a stronger promotion effect could be obtained as the experimental pressure increases. The distributions of alkanes, alkenes, dialkenes, alkynes and benzene are also influenced by the addition of nitromethane. A detailed kinetic model with 266 species and 1648 reactions was developed and validated against the mole fraction profiles of reactants, major products and important intermediates during the pyrolysis of each fuel and their binary mixture. The satisfactory model prediction to the experimental measurements permits the analysis of the kinetic effect of nitromethane initiation on the pyrolysis of n-decane. So that, the increase of the conversion rate at a lower temperature, the selectivity of decomposition products, and reduction of benzene formation are better understood.

Sewage sludge pyrolysis for thermal utilisation in furnaces; Pyrolyse von Klaerschlamm als Aufbereitungsverfahren zur thermischen Nutzung in Feuerungsanlagen

Energy Technology Data Exchange (ETDEWEB)

Storm, C; Spliethoff, H; Hein, K R.G. [Stuttgart Univ. (Germany). Inst. fuer Verfahrenstechnik und Dampfkesselwesen

1998-09-01

The degassing rate of sewage sludges increases with the pyrolysis temperature. Already at 900 degrees centigrade, the glow loss wil be less than 5 percent. The gas composition changes with increasing temperatures, and there are larger fractions of light gases like hydrogen and carbon monoxide. Non-volatile inorganic compounds are not released during pyrolysis. Volatile inorganic components behave differently: Eluation experiments with sewage sludge pyrolysis residues showed that all components under investigation are immobilized in the residue matrix and there is now washout. When the product gases were used as reduction fuels in coal furnaces, nitric oxide emissions will be reduced to less than 200 mg per cubic metre. The pyrolysis temperature was found to have an effect only at low fuel/air ratios, when gases produced at high pyrolysis temperatures resulted in lower emissions. (orig./SR) [Deutsch] Mit steigender Pyrolysetemperatur steigt die Entgasungsrate der Klaerschlaemme. Bei der Klaerschlammpyrolyse wird schon bei Temperaturen ab 900 C ein Gluehverlust von unter 5% erreicht. Die Pyrolysegaszusammensetzung aendert sich mit steigender Temperatur zugunsten von leichten Gasen wie Wasserstoff und Kohlenmonoxid. Schwerfluechtige anorganische Verbindungen werden waehrend der Pyrolyse nicht freigesetzt. Leichtfluechtige anorganische Bestandteile zeigen ein unterschiedliches Verhalten. Bei Eluierungsversuchen von Klaerschlammpyrolyseresten wurde festgestellt, dass alle untersuchten Komponenten fest in die Reststoffmatrix eingebunden werden und keine Auswaschung erfolgte. Bei der thermischen Nutzung von Gasen aus der Klaerschlammpyrolyse als Reduktionsbrennstoff in Kohlefeuerungen koennen NO{sub x} Emissionen von unter 200 mg/m{sup 3} erreicht werden. Ein Einfluss der Pyrolysetemperatur auf die NO{sub x} Emissionen konnte nur bei niedrigen Luftzahlen festgestellt werden. Hier wiesen Gase, die bei hohen Pyrolysetemperaturen entstanden, geringere Emissionen auf. (orig./SR)

Grid heterogeneity in in-silico experiments: an exploration of drug screening using DOCK on cloud environments.

Science.gov (United States)

Yim, Wen-Wai; Chien, Shu; Kusumoto, Yasuyuki; Date, Susumu; Haga, Jason

2010-01-01

Large-scale in-silico screening is a necessary part of drug discovery and Grid computing is one answer to this demand. A disadvantage of using Grid computing is the heterogeneous computational environments characteristic of a Grid. In our study, we have found that for the molecular docking simulation program DOCK, different clusters within a Grid organization can yield inconsistent results. Because DOCK in-silico virtual screening (VS) is currently used to help select chemical compounds to test with in-vitro experiments, such differences have little effect on the validity of using virtual screening before subsequent steps in the drug discovery process. However, it is difficult to predict whether the accumulation of these discrepancies over sequentially repeated VS experiments will significantly alter the results if VS is used as the primary means for identifying potential drugs. Moreover, such discrepancies may be unacceptable for other applications requiring more stringent thresholds. This highlights the need for establishing a more complete solution to provide the best scientific accuracy when executing an application across Grids. One possible solution to platform heterogeneity in DOCK performance explored in our study involved the use of virtual machines as a layer of abstraction. This study investigated the feasibility and practicality of using virtual machine and recent cloud computing technologies in a biological research application. We examined the differences and variations of DOCK VS variables, across a Grid environment composed of different clusters, with and without virtualization. The uniform computer environment provided by virtual machines eliminated inconsistent DOCK VS results caused by heterogeneous clusters, however, the execution time for the DOCK VS increased. In our particular experiments, overhead costs were found to be an average of 41% and 2% in execution time for two different clusters, while the actual magnitudes of the execution time

Formation of N{sub 2} during the fixed-bed pyrolysis of coals

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhiheng; Ohtsuka, Yasuo [Tohoku Univ., Sendai (Japan); Furimsky, E. [Natural Resources Canada, Ottawa, Ontario (Canada)

1995-12-31

Research on the fate of the nitrogen in coal during pyrolysis has attracted increased attention, since it is related with the NO{sub x} and N{sub 2}O emissions during subsequent combustion. It has been reported that coal nitrogen is initially released as tar, which is then converted to HCN and NH{sub 3} through secondary decomposition reactions. However, little attention to N{sub 2} has been paid so far. We have recently found that N{sub 2} is the dominant product in slow heating rate pyrolysis of a subbituminous coal, and that the finely dispersed iron catalyst promotes drastically the formation of N{sub 2} from a brown coal. If coal nitrogen can be removed efficiently as N{sub 2} during pyrolysis, this method would contribute to the reduction of the NO{sub x} and N{sub 2}O emissions, since such pollutants originate mostly from coal nitrogen. Therefore the present study aims at making clear the influence of coal type, pyrolysis conditions, demineralization, and iron catalyst on the formation of N{sub 2} during the fix-bed pyrolysis of several coals with different ranks.

High-speed pyrolysis with circulating heat carriers; Schnell-Pyrolyse mit zirkulierenden Waermetraegern

Energy Technology Data Exchange (ETDEWEB)

Schmalfeld, J; Albrecht, J; Solmaz, S; Zentner, U [Lurgi Energie und Umwelt GmbH, Frankfurt am Main (Germany)

1998-09-01

Yields and product compositions of pyrolysis reactions depend on the mode of heat supply, the temperature level, and the time of residue at reaction temperature. Using hot circulating granular materials mixed with solid or liquid materials (e.g. biogenic or hydrocarbon-rich residues and waste materials or refinery residues), the following important processes can be investigated: Separation of pyrolysis reaction and heat supply - accurate, optimal temperature levels for pyrolysis, e.g. between 5000 and 850 degrees centigrade - undiluted, unmixed pyrolysis gas - short times of residue of the pyrolysis gas for suppression of secondary reactions. (orig.) [Deutsch] Ausbeuten und Produktzusammensetzung von Pyrolyse-Reaktionen werden weitestgehend durch die Art und Weise der Waermezufuhr, das Temperaturniveau und die Verweilzeit bei Reaktionstemperatur bestimmt. Mit Hilfe des Prinzips heisser, umlaufender, koerniger Waermetraeger in Vermischung - fuer die Pyrolyse-Reaktion - mit festen oder fluessigen Einsatzstoffen (z.B. biogene oder kohlenwasserstoffreiche Rest-/Abfallstoffe, Raffinerie-Rueckstaende) lassen sich folgende wichtige, haeufig gewuenschte Vorgaenge realisieren: - Trennung von Pyrolyse-Reaktion und Waermeversorgung - Temperaturgenaue Pyrolyse-Reaktion auf gewuenschtem, optimalem Niveau waehlbar zwischen z.B. 5000 C und 850 C - Erhalt eines unverduennten, unvermischten Pyrolysegases - Kurze Verweilzeiten des Pyrolysegases zur Unterdrueckung von Sekundaerreaktionen. (orig.)

Calcium-rich biochar from the pyrolysis of crab shell for phosphorus removal.

Science.gov (United States)

Dai, Lichun; Tan, Furong; Li, Hong; Zhu, Nengmin; He, Mingxiong; Zhu, Qili; Hu, Guoquan; Wang, Li; Zhao, Jie

2017-08-01

Calcium-rich biochars (CRB) prepared through pyrolysis of crab shell at various temperatures were characterized for physicochemical properties and P removal potential. Elemental analysis showed that CRB was rich in calcium (22.91%-36.14%), while poor in carbon (25.21%-9.08%). FTIR, XRD and TG analyses showed that calcite-based CRB was prepared at temperature ≤600 °C, while lime-based CRB was prepared at temperature ≥700 °C. Phosphorus removal experiment showed that P removal efficiencies in 80 mg P/L phosphate solution and biogas effluent ranged from 26% to 11%, respectively, to about 100% and 63%, respectively, depending on the pyrolysis temperature of the resulting biochar. Specifically, compared to common used CaCO 3 and Ca(OH) 2 , P removal potential of calcite-based CRB was much higher than that of CaCO 3 ; while that of lime-based CRB was close to that of Ca(OH) 2 . These results suggested that CRB was competent for P removal/recovery from wastewater. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fast Pyrolysis of Four Lignins from Different Isolation Processes Using Py-GC/MS

OpenAIRE

Lin, Xiaona; Sui, Shujuan; Tan, Shun; Pittman, Charles; Sun, Jianping; Zhang, Zhijun

2015-01-01

Pyrolysis is a promising approach that is being investigated to convert lignin into higher value products including biofuels and phenolic chemicals. In this study, fast pyrolysis of four types of lignin, including milled Amur linden wood lignin (MWL), enzymatic hydrolysis corn stover lignin (EHL), wheat straw alkali lignin (AL) and wheat straw sulfonate lignin (SL), were performed using pyrolysis gas-chromatography/mass spectrometry (Py-GC/MS). Thermogravimetric analysis (TGA) showed that the...

Treatment of Lignin and Waste residues by Flash Pyrolysis

DEFF Research Database (Denmark)

Jensen, Peter Arendt; Trinh, Ngoc Trung; Dam-Johansen, Kim

pyrolysis properties were compared with the pyrolysis properti es of wood and straw. The PCR treatment of sewage sludge provides an oil that can be used for energy pur poses and a solid residue rich in in organic nutrients that may be used as fertilizer product. By fast pyroly sis of lignin from the IBUS...... be operated at low rotational speed was constructed. The new rotor systems should make it easier to make an up-scaling of the process....

Simultaneous measurements of acetylene and soot during the pyrolysis of ethylene and benzene in a shock tube

KAUST Repository

KC, Utsav

2016-10-12

Acetylene is one of the most important precursors of soot and contributes to soot growth by the hydrogen-abstraction acetylene-addition (HACA) mechanism. In this work, we undertake time-resolved simultaneous measurements of acetylene and soot behind reflected shock waves at temperatures of 1600-2200. K and pressures of 3-5. bar. Acetylene mole fraction time-histories are measured from the absorption of a quantum-cascade laser operating around 13.6. μm. The soot volume fraction, particle size and number densities are calculated from the extinction and scattering of a cw Nd:Yag laser at 532. nm. Acetylene and soot are generated from the pyrolysis of 1% benzene in argon, 2.35% ethylene in argon, and binary mixtures of ethylene with propane/methane in argon. We note that acetylene time-histories exhibit a two-stage growth during the pyrolysis of benzene, which can be correlated to the initial rapid increase of soot volume fraction and a later plateauing. In comparison to ethylene pyrolysis, the pyrolysis of benzene results in larger values of the soot volume fraction, particle diameter and number density. We compare the measured data against the values simulated using the method-of-moments routine in Chemkin-Pro and a detailed PAH mechanism based on KM2 [1] and AramcoMech 1.3 [2]. Large discrepancies are observed between the measured and predicted values of the soot parameters. The data obtained from our experiments may assist future validation and development of soot mechanisms.

The Evritania (Greece) demonstration plant of biomass pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Zabaniotou, A.A.; Karabela, A.J. [Aristotle University of Thessaloniki (Greece). Dept. of Chemical Engineering and Chemical Process Engineering Research Institute

1999-06-01

This paper is focused on describing the Evritania demonstration plant for pyrolysis of forestry biomass. This plant was constructed in the village of Voulpi, district of Evritania, in central Greece, in 1995, with a threefold purpose; development of know-how, forest fire prevention and rural development. The products are charcoal and bio-oil. The plant capacity is 1200-1450 kg/h of wet biomass and the pyrolysis temperature is approx. 400 deg C. The raw material used is Arbutus unedo, which is an evergreen broad-leaf tree which covers the area. Other agricultural waste could also be used, such as olive pits and cuttings, almond shells and cotton kernels. The paper includes the conceptual process flow sheet, the changes and improvements made during the trial phase, data from the start-up phase, and product characteristics. Comparison of the process with the Alten process is presented. Additionally, comparisons are made of product characteristics with those from other pyrolysis processes. In general, the results obtained are encouraging even though several improvements of the pilot plant are required. (author)

Method for Hot Real-Time Analysis of Pyrolysis Vapors at Pilot Scale

Energy Technology Data Exchange (ETDEWEB)

Pomeroy, Marc D [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-29

Pyrolysis oils contain more than 400 compounds, up to 60% of which do not re-volatilize for subsequent chemical analysis. Vapor chemical composition is also complicated as additional condensation reactions occur during quenching and collection of the product. Due to the complexity of the pyrolysis oil, and a desire to catalytically upgrade the vapor composition before condensation, online real-time analytical techniques such as Molecular Beam Mass Spectrometry (MBMS) are of great use. However, in order to properly sample hot pyrolysis vapors at the pilot scale, many challenges must be overcome.

Effect of operating parameters on production of bio-oil from fast pyrolysis of maize stalk in bubbling fluidized bed reactor

Directory of Open Access Journals (Sweden)

Ali Najaf

2016-09-01

Full Text Available The yield and composition of pyrolysis products depend on the characteristics of feed stock and process operating parameters. Effect of particle size, reaction temperature and carrier gas flow rate on the yield of bio-oil from fast pyrolysis of Pakistani maize stalk was investigated. Pyrolysis experiments were performed at temperature range of 360-540°C, feed particle size of 1-2 mm and carrier gas fl ow rate of 7.0-13.0 m3/h (0.61.1 m/s superficial velocity. Bio-oil yield increased with the increase of temperature followed by a decreasing trend. The maximum yield of bio-oil obtained was 42 wt% at a temperature of 490°C with the particle size of around 1.0 mm and carrier gas flow rate of 11.0 m3/h (0.9 m/s superficial velocity. High temperatures resulted in the higher ratios of char and non-condensable gas.

Aerosol processing: a wind of innovation in the field of advanced heterogeneous catalysts.

Science.gov (United States)

Debecker, Damien P; Le Bras, Solène; Boissière, Cédric; Chaumonnot, Alexandra; Sanchez, Clément

2018-04-16

Aerosol processing is long known and implemented industrially to obtain various types of divided materials and nanomaterials. The atomisation of a liquid solution or suspension produces a mist of aerosol droplets which can then be transformed via a diversity of processes including spray-drying, spray pyrolysis, flame spray pyrolysis, thermal decomposition, micronisation, gas atomisation, etc. The attractive technical features of these aerosol processes make them highly interesting for the continuous, large scale, and tailored production of heterogeneous catalysts. Indeed, during aerosol processing, each liquid droplet undergoes well-controlled physical and chemical transformations, allowing for example to dry and aggregate pre-existing solid particles or to synthesise new micro- or nanoparticles from mixtures of molecular or colloidal precursors. In the last two decades, more advanced reactive aerosol processes have emerged as innovative means to synthesise tailored-made nanomaterials with tunable surface properties, textures, compositions, etc. In particular, the "aerosol-assisted sol-gel" process (AASG) has demonstrated tremendous potential for the preparation of high-performance heterogeneous catalysts. The method is mainly based on the low-cost, scalable, and environmentally benign sol-gel chemistry process, often coupled with the evaporation-induced self-assembly (EISA) concept. It allows producing micronic or submicronic, inorganic or hybrid organic-inorganic particles bearing tuneable and calibrated porous structures at different scales. In addition, pre-formed nanoparticles can be easily incorporated or formed in a "one-pot" bottom-up approach within the porous inorganic or hybrid spheres produced by such spray drying method. Thus, multifunctional catalysts with tailored catalytic activities can be prepared in a relatively simple way. This account is an overview of aerosol processed heterogeneous catalysts which demonstrated interesting performance in

Pyrolysis of Waste Castor Seed Cake: A Thermo-Kinetics Study

Directory of Open Access Journals (Sweden)

Abdullahi Muhammad Sokoto

2018-03-01

Full Text Available Biomass pyrolysis is a thermo-chemical conversion process that is of both industrial and ecological importance. The efficient chemical transformation of waste biomass to numerous products via pyrolysis reactions depends on process kinetic rates; hence the need for kinetic models to best design and operate the pyrolysis. Also, for an efficient design of an environmentally sustainable pyrolysis process of a specific lignocellulosic waste, a proper understanding of its thermo-kinetic behavior is imperative. Thus, pyrolysis kinetics of castor seed de-oiled cake (Ricinus communis using thermogravimetric technique was studied. The decomposition of the cake was carried out in a nitrogen atmosphere with a flow rate of 100mL min-1 from ambient temperature to 900 °C. The results of the thermal profile showed moisture removal and devolatilization stages, and maximum decomposition of the cake occurred at a temperature of 200-400 °C. The kinetic parameters such as apparent activation energy, pre-exponential factor, and order of reaction were determined using Friedman (FD, Kissinger-Akahira-Sunose (KAS, and Flynn-Wall-Ozawa (FWO kinetic models. The average apparent activation energy values of 124.61, 126.95 and 129.80 kJmol-1 were calculated from the slopes of the respective models. The apparent activation energy values obtained depends on conversion, which is an evidence of multi-step kinetic process during the pyrolytic decomposition of the cake. The kinetic data would be of immense benefit to model, design and develop a suitable thermo-chemical system for the conversion of waste de-oil cake to energy carrier.

Catalytic fast pyrolysis of durian rind using silica-alumina catalyst: Effects of pyrolysis parameters.

Science.gov (United States)

Tan, Y L; Abdullah, A Z; Hameed, B H

2018-05-18

Silica-alumina catalyst was prepared and used in the catalytic fast pyrolysis of durian rind in a drop-type two-stage reactor. The effects of catalytic temperature (400 °C-600 °C) and catalyst-to-durian rind ratio (1:30-3:30) were evaluated. Bio-oil yield was increased with increased catalytic temperature due to considerable dehydration process, but it was reduced with high catalyst loading due to the overcracking of organics into light gases. Silica-alumina catalyst possessed good selectivity and the products changed according to the temperature. The major components in bio-oil were hydrocarbons, furan derivatives, and aromatic compounds at 400 °C, 500 °C, and 600 °C, respectively. The hydrogen and carbon contents of bio-oil were reduced with high catalyst loading due to the overcracking of organics, and the deoxygenation process became unfavorable. The silica-alumina catalyst worked well in catalytic fast pyrolysis of durian rind, and the condition may be adjusted based on the desired products. Copyright © 2018 Elsevier Ltd. All rights reserved.

The study of catalytic properties and phase composition of pyrolysis products of molybdophosphoric heteropolyacid. Communication 3. Environmental effect on the HPA pyrolysis

International Nuclear Information System (INIS)

Bondareva, V.M.; Andrushkevich, T.V.; Maksimovskaya, R.I.; Plyasova, L.M.; Litvak, G.S.; Burgina, E.B.

1997-01-01

Character of pyrolysis of molybdophosphonic heteropolyacid (HPA) (H 3 PMo 12 O 40 x13H 2 O) in different media (air, hydrogen, oxygen, helium, water vapour, as well reactive mixture containing acrolein) is studied within the temperature range of 200-700 deg C. With application of methods of X-ray analysis in situ, NMR 31 R and IR-spectroscopy it is shown that phase formation by HPA pyrolysis depends on the media, oxidation-reduction properties and availability of water vapour therein. 27 refs.; 5 figs

Production of bran castor biochar through slow pyrolysis

Science.gov (United States)

Pissinati de Rezende, E. I.; Mangrich, A. S.; Batista, M. G. F.; Toledo, J. M. S.; Novotny, E. H.

2012-04-01

Pyrolysis is a thermal process of great importance in the present context, since it constitutes a significant alternative to adequate use of organic waste. The principal products obtained in the pyrolysis of discarded biomass are bio-oil, biogas and biochar. Biochar, in turn, may play a relevant role when applied to the soil to sequester carbon and as a soil conditioner, a material comparable to organic matter of Indians Black Earths from the Amazon Region [1]. Seeking to determine the best methods of preparation of biochar, we studied the pyrolysis of bran castor residue of the Brazilian biodiesel industry. Eight samples, from FM1 to FM8, were prepared in a factorial design 23 using two temperature (300 and 350 °C), two heating velocity (5 and 10 °C min-1) and two period of heating (30 and 60 min). The eight samples were studied using the spectroscopy: EPR, FTIR, RMN, XPS, and elemental analysis. By elemental analysis, the samples that keep for lower temperature of pyrolysis, 300 °C, showed H/C and N/C ratios greater than the samples of 350 °C. That higher value can be attributed to chemical structure more aliphatic than aromatic mainly in the FM7 sample (V = 10 °C min-1, T = 300 °C, P = 30 min). The greater N/C ratio correlated with a superior amount of nitrogenous functions, presenting by both FM7 and FM4 samples, as determined by 13C NMR spectroscopy with absorptions in 175 ppm (amide) and 55 ppm (N-alkyl).

Pyrolysis of rice husk and corn stalk in auger reactor:Part 1. Characterization of char and gas at various temperatures

OpenAIRE

Yu, Yang; Yang, Yang; Cheng, Zhicai; Blanco, Paula H.; Liu, Ronghou; Bridgwater, A.V.; Cai, Junmeng

2016-01-01

In this study, rice husk and corn stalk have been pyrolyzed in an auger pyrolysis reactor at pyrolysis temperatures of 350, 400, 450, 500, 550, and 600 °C in order to investigate the effect of the pyrolysis temperature on the pyrolysis performance of the reactor and physicochemical properties of pyrolysis products (this paper focuses on char and gas). The results have shown that the pyrolysis temperature significantly affects the mass yields and properties of the pyrolysis products. The mass ...

In line wood plastic composite pyrolyses and HZSM-5 conversion of the pyrolysis vapors

International Nuclear Information System (INIS)

Lin, Xiaona; Zhang, Zhijun; Tan, Shun; Wang, Fengqiang; Song, Yongming; Wang, Qingwen; Pittman, Charles U.

2017-01-01

Graphical abstract: HZSM-5 can be used to catalytic convert Wood Fiber-Polypropylene or Wood Fiber-Polypropylene pyrolysis vapors into aromatic compounds in reasonable selectivities. This provides a recycling utilization WPCs wastes method. - Highlights: • Converting wood/plastic composites (WPC) wastes into aromatics. • Recycling WPC by fast pyrolysis coupled with vapor catalytic cracking. • Selective production of aromatics from WPCs and their components over HZSM-5. • Acid site concentration inside zeolite was critical for maximizing aromatic yield. • Synergistic effects between wood and plastics enhanced aromatics production. - Abstract: Wood powder-high density polyethylene (WPE) and wood powder-polypropylene (WPP) composites were pyrolyzed at 550 °C in the presence of HZSM-5 catalysts using analytical pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). Immediately passing the pyrolysis vapors through the HZSM-5 changed the product distribution by producing aromatic hydrocarbons and eliminating tar formation. Zeolite HZSM-5 was employed with three different silica-to-alumina ratios (25, 50, 260). The influence of catalysts on the yields of aliphatic and aromatic hydrocarbons, furan derivatives, lignin-derived compounds and acetic acid was studied. High yields of aliphatic hydrocarbons formed in WPE or WPP pyrolysis alone. The highest yields of aromatic hydrocarbons from WPE or WPP pyrolysis vapors over HZSM-5 occurred with a zeolite framework Si/Al ratio of 25 (more acid sites), suggesting that the concentration of acid sites inside the zeolite was critical for maximizing aromatic yield. Exposing vapors to HZSM-5 increased the hydrocarbon yields and reduced the amount of acetic acid produced, resulting in increased calorific value. The yields of typical aromatics from catalytic pyrolysis of WPP mixture and composites were higher than those of the calculated values of poplar wood and PP catalytic pyrolysis individually, indicating that a

Oyster Shell Recycling and Bone Waste Treatment Using Plasma Pyrolysis

International Nuclear Information System (INIS)

Chae, Jae Ou; Knak, S P; Knak, A N; Koo, H J; Ravi, V

2006-01-01

Investigations on the recycling of oyster shells and bone waste treatment using the plasma pyrolysis technique are presented in this paper. A arc based plasma torch operated at 25 kW was employed for the experiments. Fresh oyster shells were recycled using the plasma torch to convert them to a useful product such as CaO. Bone waste was treated to remove the infectious organic part and to vitrify the inorganic part. The time required for treatment in both cases was significantly short. Significant reduction in the weight of the samples was observed in both cases

Oyster Shell Recycling and Bone Waste Treatment Using Plasma Pyrolysis

Science.gov (United States)

Jae, Ou Chae; Knak, S. P.; Knak, A. N.; Koo, H. J.; Ravi, V.

2006-11-01

Investigations on the recycling of oyster shells and bone waste treatment using the plasma pyrolysis technique are presented in this paper. A arc based plasma torch operated at 25 kW was employed for the experiments. Fresh oyster shells were recycled using the plasma torch to convert them to a useful product such as CaO. Bone waste was treated to remove the infectious organic part and to vitrify the inorganic part. The time required for treatment in both cases was significantly short. Significant reduction in the weight of the samples was observed in both cases.

Controlled catalytic and thermal sequential pyrolysis and hydrolysis of polycarbonate and plastic waste to recover monomers

Science.gov (United States)

Evans, R.J.; Chum, H.L.

1994-06-14

A process is described using fast pyrolysis to convert a plastic waste feed stream containing polycarbonate and ABS to high value monomeric constituents prior to pyrolysis of other plastic components therein comprising: selecting a first temperature program range to cause pyrolysis of a given polymer to its high value monomeric constituents prior to a temperature range that causes pyrolysis of other plastic components; selecting an acid or base catalysts and an oxide or carbonate support for treating the feed stream to affect acid or base catalyzed reaction pathways to maximize yield or enhance separation of the high value monomeric constituents of polycarbonate and ABS in the first temperature program range; differentially heating the feed stream at a heat rate within the first temperature program range to provide differential pyrolysis for selective recovery of optimum quantities of the high value monomeric constituents prior to pyrolysis or other plastic components; separating the high value monomeric constituents from the polycarbonate to cause pyrolysis to a different high value monomeric constituent of the plastic waste and differentially heating the feed stream at the second higher temperature program range to cause pyrolysis of different high value monomeric constituents; and separating the different high value monomeric constituents. 68 figs.

Controlled catalystic and thermal sequential pyrolysis and hydrolysis of polycarbonate and plastic waste to recover monomers

Science.gov (United States)

Evans, Robert J.; Chum, Helena L.

1994-01-01

A process of using fast pyrolysis to convert a plastic waste feed stream containing polycarbonate and ABS to high value monomeric constituents prior to pyrolysis of other plastic components therein comprising: selecting a first temperature program range to cause pyrolysis of a given polymer to its high value monomeric constituents prior to a temperature range that causes pyrolysis of other plastic components; selecting an acid or base catalysts and an oxide or carbonate support for treating the feed stream to affect acid or base catalyzed reaction pathways to maximize yield or enhance separation of the high value monomeric constituents of polycarbonate and ABS in the first temperature program range; differentially heating the feed stream at a heat rate within the first temperature program range to provide differential pyrolysis for selective recovery of optimum quantities of the high value monomeric constituents prior to pyrolysis or other plastic components; separating the high value monomeric constituents from the polycarbonate to cause pyrolysis to a different high value monomeric constituent of the plastic waste and differentially heating the feed stream at the second higher temperature program range to cause pyrolysis of different high value monomeric constituents; and separating the different high value monomeric constituents.

Results of the International Energy Agency Round Robin on Fast Pyrolysis Bio-oil Production

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.; Meier, Dietrich; Oasmaa, Anja; van de Beld, Bert; Bridgwater, Anthony V.; Marklund, Magnus

2017-04-06

An international round robin study of the production of fast pyrolysis bio-oil was undertaken. Fifteen institutions in six countries contributed. Three biomass samples were distributed to the laboratories for processing in fast pyrolysis reactors. Samples of the bio-oil produced were transported to a central analytical laboratory for analysis. The round robin was focused on validating the pyrolysis community understanding of production of fast pyrolysis bio-oil by providing a common feedstock for bio-oil preparation. The round robin included: •distribution of 3 feedstock samples from a common source to each participating laboratory; •preparation of fast pyrolysis bio-oil in each laboratory with the 3 feedstocks provided; •return of the 3 bio-oil products (minimum 500 ml) with operational description to a central analytical laboratory for bio-oil property determination. The analyses of interest were: density, viscosity, dissolved water, filterable solids, CHN, S, trace element analysis, ash, total acid number, pyrolytic lignin, and accelerated aging of bio-oil. In addition, an effort was made to compare the bio-oil components to the products of analytical pyrolysis through GC/MS analysis. The results showed that clear differences can occur in fast pyrolysis bio-oil properties by applying different reactor technologies or configurations. The comparison to analytical pyrolysis method suggested that Py-GC/MS could serve as a rapid screening method for bio-oil composition when produced in fluid-bed reactors. Furthermore, hot vapor filtration generally resulted in the most favorable bio-oil product, with respect to water, solids, viscosity, and total acid number. These results can be helpful in understanding the variation in bio-oil production methods and their effects on bio-oil product composition.

Effect of precursor concentration and spray pyrolysis temperature upon hydroxyapatite particle size and density.

Science.gov (United States)

Cho, Jung Sang; Lee, Jeong-Cheol; Rhee, Sang-Hoon

2016-02-01

In the synthesis of hydroxyapatite powders by spray pyrolysis, control of the particle size was investigated by varying the initial concentration of the precursor solution and the pyrolysis temperature. Calcium phosphate solutions (Ca/P ratio of 1.67) with a range of concentrations from 0.1 to 2.0 mol/L were prepared by dissolving calcium nitrate tetrahydrate and diammonium hydrogen phosphate in deionized water and subsequently adding nitric acid. Hydroxyapatite powders were then synthesized by spray pyrolysis at 900°C and at 1500°C, using these calcium phosphate precursor solutions, under the fixed carrier gas flow rate of 10 L/min. The particle size decreased as the precursor concentration decreased and the spray pyrolysis temperature increased. Sinterability tests conducted at 1100°C for 1 h showed that the smaller and denser the particles were, the higher the relative densities were of sintered hydroxyapatite disks formed from these particles. The practical implication of these results is that highly sinterable small and dense hydroxyapatite particles can be synthesized by means of spray pyrolysis using a low-concentration precursor solution and a high pyrolysis temperature under a fixed carrier gas flow rate. © 2015 Wiley Periodicals, Inc.

Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

Energy Technology Data Exchange (ETDEWEB)

Boerresen, Knut Arne

1996-12-31

Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

Energy Technology Data Exchange (ETDEWEB)

Boerresen, Knut Arne

1997-12-31

Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

Estimation of apparent kinetic parameters of polymer pyrolysis with complex thermal degradation behavior

International Nuclear Information System (INIS)

Srimachai, Taranee; Anantawaraskul, Siripon

2010-01-01

Full text: Thermal degradation behavior during polymer pyrolysis can typically be described using three apparent kinetic parameters (i.e., pre-exponential factor, activation energy, and reaction order). Several efficient techniques have been developed to estimate these apparent kinetic parameters for simple thermal degradation behavior (i.e., single apparent pyrolysis reaction). Unfortunately, these techniques cannot be directly extended to the case of polymer pyrolysis with complex thermal degradation behavior (i.e., multiple concurrent reactions forming single or multiple DTG peaks). In this work, we proposed a deconvolution method to determine the number of apparent reactions and estimate three apparent kinetic parameters and contribution of each reaction for polymer pyrolysis with complex thermal degradation behavior. The proposed technique was validated with the model and experimental pyrolysis data of several polymer blends with known compositions. The results showed that (1) the number of reaction and (2) three apparent kinetic parameters and contribution of each reaction can be estimated reasonably. The simulated DTG curves with estimated parameters also agree well with experimental DTG curves. (author)

Development of slow pyrolysis business operations in Finland - Hidaspyro

Energy Technology Data Exchange (ETDEWEB)

Fagernas, L. [VTT Technical Research Centre of Finland, Espoo (Finland)], email: leena.fagernas@vtt.fi

2012-07-01

Birch distillate, a by-product in slow pyrolysis process of charcoal production, was found to be a promising source for biological pesticides. However, product commercialization was problematic, for EU registration is costly, and composition, active ingredients and ecotoxicological properties were not known. In addition, constant quality and process optimisation were needed. More collaboration between SMEs and research institutes was required. The primary aim was to support and develop slow pyrolysis business operations of SMEs in Finland by generating knowledge that was needed.

Techno-economic evaluation of high temperature pyrolysis processes for mixed plastic waste.

NARCIS (Netherlands)

Westerhout, R.W.J.; Westerhout, R.W.J.; van Koningsbruggen, M.P.; van der Ham, Aloysius G.J.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

1998-01-01

Three pyrolysis processes for Mixed Plastic Waste (MPW) with different reactors (Bubbling Fluidized Bed, Circulating Fluidized Bed and Rotating Cone Reactor, respectively BFB, CFB and RCR) were designed and evaluated. The estimated fixed capital investment for a 50 kton/year MPW pyrolysis plant

Equilibrium and non-equilibrium controls on the abundances of clumped isotopologues of methane during thermogenic formation in laboratory experiments: Implications for the chemistry of pyrolysis and the origins of natural gases

Science.gov (United States)

Shuai, Yanhua; Douglas, Peter M. J.; Zhang, Shuichang; Stolper, Daniel A.; Ellis, Geoffrey S.; Lawson, Michael; Lewan, Michael D.; Formolo, Michael; Mi, Jingkui; He, Kun; Hu, Guoyi; Eiler, John M.

2018-02-01

Multiply isotopically substituted molecules ('clumped' isotopologues) can be used as geothermometers because their proportions at isotopic equilibrium relative to a random distribution of isotopes amongst all isotopologues are functions of temperature. This has allowed measurements of clumped-isotope abundances to be used to constrain formation temperatures of several natural materials. However, kinetic processes during generation, modification, or transport of natural materials can also affect their clumped-isotope compositions. Herein, we show that methane generated experimentally by closed-system hydrous pyrolysis of shale or nonhydrous pyrolysis of coal yields clumped-isotope compositions consistent with an equilibrium distribution of isotopologues under some experimental conditions (temperature-time conditions corresponding to 'low,' 'mature,' and 'over-mature' stages of catagenesis), but can have non-equilibrium (i.e., kinetically controlled) distributions under other experimental conditions ('high' to 'over-mature' stages), particularly for pyrolysis of coal. Non-equilibrium compositions, when present, lead the measured proportions of clumped species to be lower than expected for equilibrium at the experimental temperature, and in some cases to be lower than a random distribution of isotopes (i.e., negative Δ18 values). We propose that the consistency with equilibrium for methane formed by relatively low temperature pyrolysis reflects local reversibility of isotope exchange reactions involving a reactant or transition state species during demethylation of one or more components of kerogen. Non-equilibrium clumped-isotope compositions occur under conditions where 'secondary' cracking of retained oil in shale or wet gas hydrocarbons (C2-5, especially ethane) in coal is prominent. We suggest these non-equilibrium isotopic compositions are the result of the expression of kinetic isotope effects during the irreversible generation of methane from an alkyl

TG-FTIR analysis of biomass pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Bassilakis, R.; Carangelo, R.M.; Wojtowicz, M.A. [Advanced Fuel Research Inc., Hartford, CT (United States)

2001-10-09

A great need exists for comprehensive biomass-pyrolysis models that could predict yields and evolution patterns of selected volatile products as a function of feedstock characteristics and process conditions. A thermogravimetric analyzer coupled with Fourier transform infrared analysis of evolving products (TG-FTIR) can provide useful input to such models in the form of kinetic information obtained under low heating rate conditions. In this work, robust TG-FTIR quantification routes were developed for infrared analysis of volatile products relevant to biomass pyrolysis. The analysis was applied to wheat straw, three types of tobacco (Burley, Oriental, and Bright) and three biomass model compounds (xylan, chlorogenic acid, and D-glucose). Product yields were compared with literature data, and species potentially quantifiable by FT-IR are reviewed. Product-evolution patterns are reported for all seven biomass samples. 41 refs., 7 figs., 2 tabs.

Model-free pyrolysis kinetics of sunflower seed and its de-oiled cake

International Nuclear Information System (INIS)

Özsin, Gamzenur; Kilic, Murat; Pütün, Ersan; Pütün, Ayşe E.

2015-01-01

Sunflower seed wastes from oil production are a potential biomass source for bio- energy production due to extensive and excessive oil production from sunflower seeds. Considering global energy requirement, pyrolysis seems a promising route for utilisation of such industrial biomass wastes. To develop, scale-up and operate pyrolysis plants efficiently, a fundamental understanding of pyrolysis behaviour and kinetics is essential. In this study, sunflower seeds and their waste cakes after extraction were evaluated as a potential biomass feedstock in pyrolysis process. In order to enlighten pyrolytic degradation behaviours, samples were pyrolysed under dynamic conditions from room temperature to 1000 °C using multiple heating rates. The main degradation regimes of the structures were characterized by high weight loss rates. Reaction kinetics was investigated with respect to conversion degree. It is anticipated that this study will be beneficial in optimizing the thermochemical processes, which may be utilize industrial biomass wastes. (full text)

Characterisation and properties of homo- and heterogenously phosphorylated nanocellulose.

Science.gov (United States)

Kokol, Vanja; Božič, Mojca; Vogrinčič, Robert; Mathew, Aji P

2015-07-10

Nano-sized cellulose ester derivatives having phosphoryl side groups were synthesised by phosphorylation of nanofibrilated cellulose (NFC) and nanocrystaline cellulose (NCC), using different heterogeneous (in water) and homogeneous (in molten urea) processes with phosphoric acid as phosphoryl donor. The phosphorylation mechanism, efficacy, stability, as well as its influence on the NC crystallinity and thermal properties, were evaluated using ATR-FTIR and (13)C NMR spectroscopies, potentiometric titration, capillary electrophoresis, X-ray diffraction, colorimetry, thermogravimmetry and SEM. Phosphorylation under both processes created dibasic phosphate and monobasic tautomeric phosphite groups at C6 and C3 positioned hydroxyls of cellulose, yielded 60-fold (∼1,173 mmol/kg) and 2-fold (∼1.038 mmol/kg) higher surface charge density for p-NFC and p-NCC, respectively, under homogenous conditions. None of the phosphorylations affected neither the NC crystallinity degree nor the structure, and noticeably preventing the derivatives from weight loss during the pyrolysis process. The p-NC showed high hydrolytic stability to water at all pH mediums. Reusing of the treatment bath was examined after the heterogeneous process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Estimation of risks by chemicals produced during laser pyrolysis of tissues

Science.gov (United States)

Weber, Lothar W.; Spleiss, Martin

1995-01-01

Use of laser systems in minimal invasive surgery results in formation of laser aerosol with volatile organic compounds of possible health risk. By use of currently identified chemical substances an overview on possibly associated risks to human health is given. The class of the different identified alkylnitriles seem to be a laser specific toxicological problem. Other groups of chemicals belong to the Maillard reaction type, the fatty acid pyrolysis type, or even the thermally activated chemolysis. In relation to the available different threshold limit values the possible exposure ranges of identified substances are discussed. A rough estimation results in an exposure range of less than 1/100 for almost all substances with given human threshold limit values without regard of possible interactions. For most identified alkylnitriles, alkenes, and heterocycles no threshold limit values are given for lack of, until now, practical purposes. Pyrolysis of anaesthetized organs with isoflurane gave no hints for additional pyrolysis products by fragment interactions with resulting VOCs. Measurements of pyrolysis gases resulted in detection of small amounts of NO additionally with NO2 formation at plasma status.

Fast pyrolysis of sugarcane and cassava residues in a free-fall reactor

International Nuclear Information System (INIS)

Pattiya, Adisak; Sukkasi, Sittha; Goodwin, Vituruch

2012-01-01

Fast pyrolysis of agricultural residues from sugarcane and cassava plantations was carried out in a laboratory-scale free-fall reactor unit. The objectives of this work were to investigate the effects of biomass types and pyroysis conditions, such as reactor temperature, condensation temperature, nitrogen flow rate and run duration, on pyrolysis product distribution, as well as to study the basic properties of the products. The results showed that all of the parameters affected the product distribution. The optimum reactor temperatures for maximising bio-oil yield were in the range of 350–450 °C. About 70 wt% of bio-oil yield could be obtained by pyrolysis of cassava stalk at a reactor temperature of 450 °C and a primary condensation temperature of 10 °C. It was also found that the minimum flow rate of nitrogen for obtaining high bio-oil yield was 1.5 l/min. The product characterisation showed that the bio-oil and char produced from the agricultural residues with the free-fall reactor unit were to a certain extent similar to those produced from different types of biomass with different types of pyrolysis reactor configurations. -- Highlights: ► Fast pyrolysis of sugarcane and cassava agricultural residues was carried out in a laboratory-scale free-fall reactor unit. ► The effects of process parameters on product yields were investigated. ► The process parameters included reactor temperature, condensation temperature, nitrogen flow rate and run duration. ► Basic properties of pyrolysis products were examined.

The use of tyre pyrolysis oil in diesel engines.

Science.gov (United States)

Murugan, S; Ramaswamy, M C; Nagarajan, G

2008-12-01

Tests have been carried out to evaluate the performance, emission, and combustion characteristics of a single cylinder direct injection diesel engine fueled with 10%, 30%, and 50% of tyre pyrolysis oil (TPO) blended with diesel fuel (DF). The TPO was derived from waste automobile tyres through vacuum pyrolysis. The combustion parameters such as heat release rate, cylinder peak pressure, and maximum rate of pressure rise also analysed. Results showed that the brake thermal efficiency of the engine fueled with TPO-DF blends increased with an increase in blend concentration and reduction of DF concentration. NO(x), HC, CO, and smoke emissions were found to be higher at higher loads due to the high aromatic content and longer ignition delay. The cylinder peak pressure increased from 71 bars to 74 bars. The ignition delays were longer than with DF. It is concluded that it is possible to use tyre pyrolysis oil in diesel engines as an alternate fuel in the future.

Co-pyrolysis of biomass and plastic wastes: investigation of apparent kinetic parameters and stability of pyrolysis oils

Science.gov (United States)

Fekhar, B.; Miskolczi, N.; Bhaskar, T.; Kumar, J.; Dhyani, V.

2018-05-01

This work is dedicated to the co-pyrolysis of real waste high density polyethylene (HDPE) and biomass (rice straw) obtained from agriculture. Mixtures of raw materials were pyrolyzed in their 0%/100%, 30%/70%, 50%/50%, 70%/30%, 100%/0% ratios using a thermograph. The atmosphere was nitrogen, and a constant heating rate was used. Based on weight loss and DTG curves, the apparent reaction kinetic parameters (e.g., activation energy) were calculated using first-order kinetic approach and Arrhenius equation. It was found that decomposition of pure plastic has approximately 280 kJ/mol activation energy, while that of was considerably less in case of biomass. Furthermore, HDPE decomposition takes by one stage, while that of biomass was three stages. The larger amount of raw materials (100 g) were also pyrolyzed in the batch rig at 550°C to obtain products for analysis focussing to their long-term application. Pyrolysis oils were investigated by Fourier transformed infrared spectroscopy and standardized methods, such as density, viscosity, boiling range determination. It was concluded, that higher plastic ratio in raw material had the advantageous effect to the pyrolysis oil long-term application. E.g., the concentration of oxygenated compounds, such as aldehydes, ketones, carboxylic acids or even phenol and its derivate could be significantly decreased, which had an advantageous effect to their corrosion property. Lower average molecular weight, viscosity, and density were measured as a function of plastic content.

CHARACTERISTICS OF CORN STALK HEMICELLULOSE PYROLYSIS IN A TUBULAR REACTOR

OpenAIRE

Gao-Jin Lv; Shu-Bin Wu; Rui Lou

2010-01-01

Pyrolysis characteristics of corn stalk hemicellulose were investigated in a tubular reactor at different temperatures, with focus mainly on the releasing profiles and forming behaviors of pyrolysis products (gas, char, and tar). The products obtained were further identified using various approaches (including GC, SEM, and GC-MS) to understand the influence of temperature on product properties and compositions. It was found that the devolatilization of hemicellulose mainly occurred at low tem...

Effect of hydrothermal carbonization on migration and environmental risk of heavy metals in sewage sludge during pyrolysis.

Science.gov (United States)

Liu, Tingting; Liu, Zhengang; Zheng, Qingfu; Lang, Qianqian; Xia, Yu; Peng, Nana; Gai, Chao

2018-01-01

The heavy metals distribution during hydrothermal carbonization (HTC) of sewage sludge, and pyrolysis of the resultant hydrochar was investigated and compared with raw sludge pyrolysis. The results showed that HTC reduced exchangeable/acid-soluble and reducible fraction of heavy metals and lowered the potential risk of heavy metals in sewage sludge. The pyrolysis favored the transformation of extracted/mobile fraction of heavy metals to residual form especially at high temperature, immobilizing heavy metals in the chars. Compared to the chars from raw sludge pyrolysis, the chars derived from hydrochar pyrolysis was more alkaline and had lower risk and less leachable heavy metals, indicating that pyrolysis imposed more positive effect on immobilization of heavy metals for the hydrochar than for sewage sludge. The present study demonstrated that HTC is a promising pretreatment prior to pyrolysis from the perspective of immobilization of heavy metals in sewage sludge. Copyright © 2017 Elsevier Ltd. All rights reserved.

Catalytic hydrotreatment of pyrolysis liquids and fractions : Catalyst Development and Process Studies

NARCIS (Netherlands)

Yin, Wang

2017-01-01

The use of sustainable and renewable lignocellulosic biomass is of particular interest to (partly) replace fossil resources. Fast pyrolysis is a promising technology to convert lignocellulosic biomass to a liquid energy carrier. The products, also known as fast pyrolysis liquids (PLs), have a higher

Production of Lunar Oxygen Through Vacuum Pyrolysis

National Research Council Canada - National Science Library

Matchett, John

2006-01-01

.... The vacuum pyrolysis method of oxygen production from lunar regolith presents a viable option for in situ propellant production because of its simple operation involving limited resources from earth...

Catalytic pyrolysis of Laminaria japonica over nanoporous catalysts using Py-GC/MS

Directory of Open Access Journals (Sweden)

Jeon Jong-Ki

2011-01-01

Full Text Available Abstract The catalytic pyrolysis of Laminaria japonica was carried out over a hierarchical meso-MFI zeolite (Meso-MFI and nanoporous Al-MCM-48 using pyrolysis gas chromatography/mass spectrometry (Py-GC/MS. The effect of the catalyst type on the product distribution and chemical composition of the bio-oil was examined using Py-GC/MS. The Meso-MFI exhibited a higher activity in deoxygenation and aromatization during the catalytic pyrolysis of L. japonica. Meanwhile, the catalytic activity of Al-MCM-48 was lower than that of Meso-MFI due to its weak acidity.

Characterization of Hydrotreated Fast Pyrolysis Liquids

NARCIS (Netherlands)

Oasmaa, A.; Kuoppala, E.; Ardiyanti, A.; Venderbosch, R. H.; Heeres, H. J.

This paper focuses on analytical methods to determine the composition of hydrotreated fast pyrolysis liquids. With this information, it is possible to gain insights in the chemical transformations taking place during catalytic hydrotreatment (hydrogenation and/or hydrodeoxygenation, H DO) of

Chapter 8: Pyrolysis Mechanisms of Lignin Model Compounds Using a Heated Micro-Reactor

Energy Technology Data Exchange (ETDEWEB)

Robichaud, David J.; Nimlos, Mark R.; Ellison, G. Barney

2015-10-03

Lignin is an important component of biomass, and the decomposition of its thermal deconstruction products is important in pyrolysis and gasification. In this chapter, we investigate the unimolecular pyrolysis chemistry through the use of singly and doubly substituted benzene molecules that are model compounds representative of lignin and its primary pyrolysis products. These model compounds are decomposed in a heated micro-reactor, and the products, including radicals and unstable intermediates, are measured using photoionization mass spectrometry and matrix isolation infrared spectroscopy. We show that the unimolecular chemistry can yield insight into the initial decomposition of these species. At pyrolysis and gasification severities, singly substituted benzenes typically undergo bond scission and elimination reactions to form radicals. Some require radical-driven chain reactions. For doubly substituted benzenes, proximity effects of the substituents can change the reaction pathways.

Selective Hydrodeoxygenation of 5-Hydroxymethylfurfural to 2,5-Dimethylfuran over Heterogeneous Iron Catalysts.

Science.gov (United States)

Li, Jiang; Liu, Jun-Ling; Liu, He-Yang; Xu, Guang-Yue; Zhang, Jun-Jie; Liu, Jia-Xing; Zhou, Guang-Lin; Li, Qin; Xu, Zhi-Hao; Fu, Yao

2017-04-10

This work provided the first example of selective hydrodeoxygenation of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) over heterogeneous Fe catalysts. A catalyst prepared by the pyrolysis of an Fe-phenanthroline complex on activated carbon at 800 °C was demonstrated to be the most active heterogeneous Fe catalyst. Under the optimal reaction conditions, complete conversion of HMF was achieved with 86.2 % selectivity to DMF. The reaction pathway was investigated thoroughly, and the hydrogenation of the C=O bond in HMF was demonstrated to be the rate-determining step during the hydrodeoxygenation, which could be accelerated greatly by using alcohol solvents as additional H-donors. The excellent stability of the Fe catalyst, which was probably a result of the well-preserved active species and the pore structure of the Fe catalyst in the presence of H 2 , was demonstrated in batch and continuous flow fixed-bed reactors. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Flash pyrolysis of coal-solvent slurry prepared from the oxidized coal and the coal dissolved in solvent; Ichibu yokaishita sanka kaishitsutan slurry no jinsoku netsubunkai

Energy Technology Data Exchange (ETDEWEB)

Maki, T.; Mae, K.; Okutsu, H.; Miura, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1996-10-28

In order to develop a high-efficiency coal pyrolysis method, flash pyrolysis was experimented on slurry prepared by using liquid-phase oxidation reformed coal and a methanol-based solvent mixture. Australian Morwell coal was used for the experiment. The oxidized coal, into which carboxyl groups have been introduced, has the condensation structure relaxed largely, and becomes highly fluid slurry by means of the solvent. Char production can be suppressed by making the oxidation-pretreated coal into slurry, resulting in drastically improved pyrolytic conversion. The slurry was divided into dissolved solution, dried substance, extracted residue, and residual slurry, which were pyrolized independently. The dissolved solution showed very high conversion. Improvement in the conversion is contributed by separating the dissolved substances (coal macromolecules) at molecular levels, coagulating the molecules, suppressing cross-link formation, and reducing molecular weight of the dissolved substances. Oxidized coal can be dissolved to 80% or higher by using several kinds of mixed solvents. As a result of the dissolution, a possibility was suggested on pyrolysis which is easy in handling and high in conversion. 7 refs., 6 figs., 2 tabs.

A Comparison of Flame Spread Characteristics over Solids in Concurrent Flow Using Two Different Pyrolysis Models

Directory of Open Access Journals (Sweden)

Ya-Ting Tseng

2011-01-01

Full Text Available Two solid pyrolysis models are employed in a concurrent-flow flame spread model to compare the flame structure and spreading characteristics. The first is a zeroth-order surface pyrolysis, and the second is a first-order in-depth pyrolysis. Comparisons are made for samples when the spread rate reaches a steady value and the flame reaches a constant length. The computed results show (1 the mass burning rate distributions at the solid surface are qualitatively different near the flame (pyrolysis base region, (2 the first-order pyrolysis model shows that the propagating flame leaves unburnt solid fuel, and (3 the flame length and spread rate dependence on sample thickness are different for the two cases.

Mixed-waste pyrolysis of biomass and plastics waste – A modelling approach to reduce energy usage

International Nuclear Information System (INIS)

Oyedun, Adetoyese Olajire; Gebreegziabher, Tesfaldet; Ng, Denny K.S.; Hui, Chi Wai

2014-01-01

Thermal co-processing of waste mixtures had gained a lot of attention in the last decade. This is largely due to certain synergistic effects such as higher quantity and better quality of oil, limited supply of certain feedstock and improving the overall pyrolysis process. Many experiments have been conducted via TGA analysis and different reactors to achieve the stated synergistic effects in co-pyrolysis of biomass and plastic wastes. The thermal behaviour of plastics during pyrolysis is different from that of biomass because its decomposition happens at a high temperature range with sudden release of volatile compared to biomass which have a wide range of thermal decomposition. A properly designed recipe and operational strategy of mixing feedstock can ease the operational difficulties and at the same time decrease energy consumption and/or improve the product yield. Therefore it is worthwhile to study the possible synergistic effects on the overall energy used during co-pyrolysis process. In this work, two different modelling approaches were used to study the energy related synergistic effect between polystyrene (PS) and bamboo waste. The mass loss and volatile generation profiles show that significant interactions between the two feedstocks exist. The results also show that both modelling approaches give an appreciable synergy effect of reduction in overall energy when PS and bamboo are co-pyrolysed together. However, the second approach which allows interaction between the two feedstocks gives a more reduction in overall energy usage up to 6.2% depending on the ratio of PS in the mixed blend. - Highlights: • Proposed the mixed-waste pyrolysis modelling via two modelling approaches. • Study the energy related synergistic effects when plastics and biomass are pyrolysed together. • Mass loss and volatile generation profiles show the existence of significant interactions. • Energy usage can be reduced by up to 6.2% depending on the percentage of the plastic

High quality bio-oil from catalytic flash pyrolysis of lignocellulosic biomass over alumina-supported sodium carbonate

NARCIS (Netherlands)

Ali Imran, A.; Bramer, Eduard A.; Seshan, Kulathuiyer; Brem, Gerrit

2014-01-01

Performance of a novel alumina-supported sodium carbonate catalyst was studied to produce a valuable bio-oil from catalytic flash pyrolysis of lignocellulosic biomass. Post treatment of biomass pyrolysis vapor was investigated in a catalyst fixed bed reactor at the downstream of the pyrolysis

High quality bio-oil from catalytic flash pyrolysis of lignocellulosic biomass over alumina-supported sodium carbonate

KAUST Repository

Imran, Ali

2014-11-01

Performance of a novel alumina-supported sodium carbonate catalyst was studied to produce a valuable bio-oil from catalytic flash pyrolysis of lignocellulosic biomass. Post treatment of biomass pyrolysis vapor was investigated in a catalyst fixed bed reactor at the downstream of the pyrolysis reactor. In-situ catalytic upgrading of biomass pyrolysis vapor was conducted in an entrained flow pyrolysis reactor by feeding a premixed feedstock of the catalyst and biomass. Na2CO3/gamma-Al2O3 was very effective for de-oxygenation of the pyrolysis liquid and oxygen content of the bio-oil was decreased from 47.5 wt.% to 16.4 wt.%. An organic rich bio-oil was obtained with 5.8 wt.% water content and a higher heating value of 36.1 MJ/kg. Carboxylic acids were completely removed and the bio-oil had almost a neutral pH. This bio-oil of high calorific low, low water and oxygen content may be an attractive fuel precursor. In-situ catalytic upgrading of biomass pyrolysis vapor produced a very similar quality bio-oil compared to post treatment of pyrolysis vapors, and shows the possible application of Na2CO3/gamma-Al2O3 in a commercial type reactor system such as a fluidized bed reactor. (C) 2014 Elsevier B.V. All rights reserved.

Co-pyrolysis of swine manure with agricultural plastic waste: Laboratory-scale study

Science.gov (United States)

Manure-derived biochar is the solid product resulting from pyrolysis of animal manures. It has considerable potential both to improve soil quality with high levels of nutrients and to reduce contaminants in water and soil. However, the combustible gas produced from manure pyrolysis generally does no...

Slow and pressurized co-pyrolysis of coal and agricultural residues

International Nuclear Information System (INIS)

Aboyade, Akinwale O.; Carrier, Marion; Meyer, Edson L.; Knoetze, Hansie; Görgens, Johann F.

2013-01-01

Highlights: ► Evaluation of co-pyrolysis of coal and biomass in pressurized packed bed reactor. ► Relative influence of coal–biomass mix ratio, temperature and pressure also investigated. ► Results show significant synergy or chemical interactions in the vapor phase. ► Synergistic interactions did not influence distribution of lumped solid liquid and gas products. - Abstract: The distribution of products from the slow heating rate pyrolysis of coal, corn residues (cobs and stover), sugarcane bagasse and their blends were investigated by slow pressurized pyrolysis in a packed bed reactor. A factorial experimental design was implemented to establish the relative significance of coal–biomass mix ratio, temperature and pressure on product distribution. Results showed that the yield and composition of tar and other volatile products were mostly influenced by mix ratio, while temperature and pressure had a low to negligible significance under the range of conditions investigated. Analysis of the composition of condensates and gas products obtained showed that there was significant synergy or chemical interactions in the vapor phase during co-pyrolysis of coal and biomass. However, the interactions did not significantly affect the relative distribution of the lumped solid, liquid and gas products obtained from the blends, beyond what would be expected assuming additive behavior from the contributing fuels.

Thermogravimetric-Mass Spectrometric Study of the Pyrolysis Behavior of PVC

Institute of Scientific and Technical Information of China (English)

SUN Qing-lei; SHI Xin-gang; LIN Yun-liang; ZHU He; WANG Xiao; CHENG Chuan-ge; LIU Jian-hua

2007-01-01

The pyrolysis characteristics of PVC were systematically investigated using a Netzschne TG thermo-balance coupled to a quadrupole mass spectrometer. The pyrolysis conditions were 0.1 MPa of Ar, a heating rate of 10 ℃/min and a final temperature of 1000 ℃. Both the thermogravimetric properties and the simultaneous evolution of gaseous products during pyrolysis were studied. The TG/DTG results showed that as the pyrolysis temperature increases the weight loss and weight loss rate of PVC increases. Near 412 ℃ the weight loss rate attained its peak value. At higher temperatures the rate of loss gradually decreases. The gases evolved during thermogravimetric analysis were analyzed by a mass spectrometer, monitoring the relative intensity of HCl, C6H6, light hydrocarbon and chlorine-containing gases. The evolution curves showed that HCl, C6H6, light hydrocarbon and chlorine-containing gases all peak at about 416 ℃. This is consistent with the fact that the weight loss curves also peak at about 412 ℃. The extensive HCl evolution is consistent with the high chlorine content of PVC. The formation of these gases can be explained by considering these reactions: dehydrochlorination, intramolecular cyclization and the addition of HCl to unsaturated hydrocarbons.

Hybrid-renewable processes for biofuels production: concentrated solar pyrolysis of biomass residues

Energy Technology Data Exchange (ETDEWEB)

George, Anthe [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Geier, Manfred [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dedrick, Daniel E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2014-10-01

The viability of thermochemically-derived biofuels can be greatly enhanced by reducing the process parasitic energy loads. Integrating renewable power into biofuels production is one method by which these efficiency drains can be eliminated. There are a variety of such potentially viable "hybrid-renewable" approaches; one is to integrate concentrated solar power (CSP) to power biomass-to-liquid fuels (BTL) processes. Barriers to CSP integration into BTL processes are predominantly the lack of fundamental kinetic and mass transport data to enable appropriate systems analysis and reactor design. A novel design for the reactor has been created that can allow biomass particles to be suspended in a flow gas, and be irradiated with a simulated solar flux. Pyrolysis conditions were investigated and a comparison between solar and non-solar biomass pyrolysis was conducted in terms of product distributions and pyrolysis oil quality. A novel method was developed to analyse pyrolysis products, and investigate their stability.

Production of activated carbon by using pyrolysis process in an ammonia atmosphere

Science.gov (United States)

Indayaningsih, N.; Destyorini, F.; Purawiardi, R. I.; Insiyanda, D. R.; Widodo, H.

2017-04-01

Activated carbon is materials that have wide applications, including supercapacitor materials, absorbent in chemical industry, and absorbent material in the chemical industry. This study has carried out for the manufacturing of activated carbon from inexpensive materials through efficient processes. Carbon material was made from coconut fibers through pyrolysis process at temperature of 650, 700, 750 and 800°C. Aim of this study was to obtain carbon material that has a large surface area. Pyrolysis process is carried out in an inert atmosphere (N2 gas) at a temperature of 450°C for 30 minutes, followed by pyrolysis process in an ammonia atmosphere at 800°C for 2 hours. The pyrolysis results showed that the etching process in ammonia is occurred; as it obtained some greater surface area when compared with the pyrolisis process in an atmosphere by inert gas only. The resulted activated carbon also showed to have good properties in surface area and total pore volume.

Thermogravimetric study on pyrolysis kinetics of Chlorella pyrenoidosa and bloom-forming cyanobacteria.

Science.gov (United States)

Hu, Mian; Chen, Zhihua; Guo, Dabin; Liu, Cuixia; Xiao, Bo; Hu, Zhiquan; Liu, Shiming

2015-02-01

The pyrolysis process of two microalgae, Chlorella pyrenoidosa (CP) and bloom-forming cyanobacteria (CB) was examined by thermo-gravimetry to investigate their thermal decomposition behavior under non-isothermal conditions. It has found that the pyrolysis of both microalgae consists of three stages and stage II is the major mass reduction stage with mass loss of 70.69% for CP and 64.43% for CB, respectively. The pyrolysis kinetics of both microalgae was further studied using single-step global model (SSGM) and distributed activation energy model (DAEM). The mean apparent activation energy of CP and CB in SSGM was calculated as 143.71 and 173.46 kJ/mol, respectively. However, SSGM was not suitable for modeling pyrolysis kinetic of both microalgae due to the mechanism change during conversion. The DAEM with 200 first-order reactions showed an excellent fit between simulated data and experimental results. Copyright © 2014 Elsevier Ltd. All rights reserved.

Pyrolysis of olive residue/low density polyethylene mixture:Part I Thermogravimetric kinetics

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

This paper demonstrates the thermal pyrolysis of olive residue, low density polyethylene (LDPE) and olive residue/LDPE mixture in an inert atmosphere of N2 using thermogravimetric analysis (TGA). Measurements were carried out in the temperature range 300K~973K at heating rates of 2K/min, 10K/min, 20K/min and 50K/min. Based on the results obtained, three temperature regimes were selected for studying the non-isothermal kinetics of olive residue/LDPE mixture. The first two were dominated by the olive residue pyrolysis, while the third was linked to the LDPE pyrolysis, which occurred at much higher temperatures. Discrepancies between the experimental and calculated TG/DTG profiles were considered as a measurement of the extent of interactions occurring on co-pyrolysis. The maximum degradation temperatures of each component in the mixture were higher than those the individual components;thus an increase in thermal stability was expected. The kinetic parameters associated with thermal degradation were determined using Friedman isoconversional method.

Measurements of temperature of the tungsten hexa-ethoxide pyrolysis flame using IR camera

CSIR Research Space (South Africa)

Mudau, AE

2010-09-01

Full Text Available In laser pyrolysis, temperature measurement and control plays a vital role during the development of nanoparticles. Authors present the results of temperature measurements using infrared camera on a tungsten hexa-ethoxide pyrolysis flame used...

The release of nitrogen in coal combustion and pyrolysis

International Nuclear Information System (INIS)

Varey, J.E.; Hindmarsh, C.J.; Thomas, K.M.

1994-01-01

Environmental aspects of coal utilization are a major concern. Recent advances in the development of low NO x burners and the emerging technologies of fluidized bed combustion have led to the identification of coal char nitrogen as the major contributor to the nitrogen oxides released during combustion. The temperature programmed combustion and pyrolysis of a series of coals covering a wide range of rank have been investigated. In addition, maceral concentrates have been investigated to assess the variation in the combustion behavior and the release of nitrogen in the pyrolysis and combustion of macerals. This investigation has involved the use of thermogravimetric analysis - mass spectrometry (TG-MS) with two sampling options: (1) ∼1cm from the sample and (2) at the exit of the TG. The former allows reactive species to be identified in the combustion of the coals. These temperature programmed combustion results have been compared with similar measurements carried out at the exit of the TG where the products are at equilibrium. In addition, pyrolysis studies have been carried out under similar conditions. The results show that reactive intermediate species such as HCN, (CN) 2 , COS etc. can be detected in the combustion products. The evolution of these species during combustion are compared with the pyrolysis products of the coal. The results are discussed in relation to the structure of the coals and the conversion of volatile species and char nitrogen to nitrogen oxides

Pore Scale Analysis of Oil Shale/Sands Pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Lin, Chen-Luh [Univ. of Utah, Salt Lake City, UT (United States); Miller, Jan [Univ. of Utah, Salt Lake City, UT (United States)

2011-03-01

There are important questions concerning the quality and volume of pore space that is created when oil shale is pyrolyzed for the purpose of producing shale oil. In this report, 1.9 cm diameter cores of Mahogany oil shale were pyrolyzed at different temperatures and heating rates. Detailed 3D imaging of core samples was done using multiscale X-ray computed tomography (CT) before and after pyrolysis to establish the pore structure. The pore structure of the unreacted material was not clear. Selected images of a core pyrolyzed at 400oC were obtained at voxel resolutions from 39 microns (Οm) to 60 nanometers (nm). Some of the pore space created during pyrolysis was clearly visible at these resolutions and it was possible to distinguish between the reaction products and the host shale rock. The pore structure deduced from the images was used in Lattice Boltzmann simulations to calculate the permeability in the pore space. The permeabilities of the pyrolyzed samples of the silicate-rich zone were on the order of millidarcies, while the permeabilities of the kerogen-rich zone after pyrolysis were very anisotropic and about four orders of magnitude higher.

Technical and environmental assessment of the scrap tire vacuum pyrolysis process

International Nuclear Information System (INIS)

Roy, C.; Caumia, B. de; Lebrecque, B.; Blanchette, D.; Pakdel, H.; Roy, V.

1991-01-01

Tire recycling has become a necessity because of the huge piles of tires which represent a threat to the environment. There is about one worn tire produced per year and per person in the developed countries. The used tires represent a source of energy and valuable chemical products. By thermal decomposition of rubber under reduced pressure, it is possible to recover the useful compounds. A step by step approach has been used, from bench-scale batch systems, to process development and finally pilot plant, to experiment and develop vacuum pyrolysis of used tires. Yields are: 55% oil, 25% carbon black, 9% steel, 5% fiber and 6% gas. The maximum recovery of oil was performed at 415 degree C below 2 kPa abs. The specific gravity of this oil was 0.95, its gross heating value was 43 MJ/kg and total sulfur content about 0.8%. It was rich in limonene, benzol and other petrochemical components. The carbon black favorably compared with the low standard grades and may find an application in low grade rubber goods following further research and development. From an environmental point of view, the quality of the gas emissions was found to be acceptable based on the province of Quebec regulations. The aqueous phase contains toxic substances which will be eliminated after blending and burning it with pyrolysis oils used to heat up the reactor. The heat of pyrolysis for the reactions is low, estimated around 700 kJ/kg. The process has been tested in a 200 kg/h pilot plant, which positively demonstrated the possibility of continuously feeding large chunks of rubber under a vacuo. The process feasibility is promising, with returns on the investment of 31% after three years of operation. 9 refs., 4 figs., 8 tabs

Pyrolysis and Gasification Kinetics of Large Biomass Particles

Energy Technology Data Exchange (ETDEWEB)

Svenson, Jenny; Hagstroem, Magnus; Andersson, Patrik U.; Loenn, Benny; Pettersson, Jan B.C. [Goteborg Univ. (Sweden). Dep. of Chemistry, Atmospheric Science; Davidsson, Kent O. [Chalmers Univ. of Technology, Goeteborg (Sweden). Energy Conversion

2004-05-01

The aim of the project is to provide experimental data on single biomass particle pyrolysis that have an applied as well as a fundamental bearing. Transport phenomena and kinetics on the single particle level are characterized, including heat and mass transport processes. New experimental techniques and methods are applied and developed within the project. A single-particle reactor has been developed for the investigations, and several detection techniques including fast thermogravimetric analysis, molecular beam mass spectrometry, laser spectroscopy, video recording and pyrometry are applied. The experimental data are used to develop robust models for pyrolysis and gasification, which are essential components in the design of gasification and combustion reactors.

Life Cycle Assessment of Gasoline and Diesel Produced via Fast Pyrolysis and Hydroprocessing

Energy Technology Data Exchange (ETDEWEB)

Hsu, D. D.

2011-03-01

In this work, a life cycle assessment (LCA) estimating greenhouse gas (GHG) emissions and net energy value (NEV) of the production of gasoline and diesel from forest residues via fast pyrolysis and hydroprocessing, from production of the feedstock to end use of the fuel in a vehicle, is performed. The fast pyrolysis and hydrotreating and hydrocracking processes are based on a Pacific Northwest National Laboratory (PNNL) design report. The LCA results show GHG emissions of 0.142 kg CO2-equiv. per km traveled and NEV of 1.00 MJ per km traveled for a process using grid electricity. Monte Carlo uncertainty analysis shows a range of results, with all values better than those of conventional gasoline in 2005. Results for GHG emissions and NEV of gasoline and diesel from pyrolysis are also reported on a per MJ fuel basis for comparison with ethanol produced via gasification. Although pyrolysis-derived gasoline and diesel have lower GHG emissions and higher NEV than conventional gasoline does in 2005, they underperform ethanol produced via gasification from the same feedstock. GHG emissions for pyrolysis could be lowered further if electricity and hydrogen are produced from biomass instead of from fossil sources.

Jobs and Economic Development Impact (JEDI) User Reference Guide: Fast Pyrolysis Biorefinery Model

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yimin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldberg, Marshall [MRG and Associates, Nevada City, CA (United States)

2015-02-01

This guide -- the JEDI Fast Pyrolysis Biorefinery Model User Reference Guide -- was developed to assist users in operating and understanding the JEDI Fast Pyrolysis Biorefinery Model. The guide provides information on the model's underlying methodology, as well as the parameters and data sources used to develop the cost data utilized in the model. This guide also provides basic instruction on model add-in features and a discussion of how the results should be interpreted. Based on project-specific inputs from the user, the JEDI Fast Pyrolysis Biorefinery Model estimates local (e.g., county- or state-level) job creation, earnings, and output from total economic activity for a given fast pyrolysis biorefinery. These estimates include the direct, indirect and induced economic impacts to the local economy associated with the construction and operation phases of biorefinery projects.Local revenue and supply chain impacts as well as induced impacts are estimated using economic multipliers derived from the IMPLAN software program. By determining the local economic impacts and job creation for a proposed biorefinery, the JEDI Fast Pyrolysis Biorefinery Model can be used to field questions about the added value biorefineries might bring to a local community.

Hydrodeoxygenation of pyrolysis oil fractions: process understanding and quality assessment through co-processing in refinery units

NARCIS (Netherlands)

De Miguel Mercader, F.; de Miguel Mercader, Ferran; Groeneveld, M.J.; Kersten, Sascha R.A.; Geantet, Christophe; Toussaint, Guy; Way, Nico W.J.; Schaverien, Colin J.; Hogendoorn, Kees

2011-01-01

Hydrodeoxygenation (HDO) of pyrolysis oil fractions was studied to better understand the HDO of whole pyrolysis oil and to assess the possibility to use individual upgrading routes for these fractions. By mixing pyrolysis oil and water in a 2:1 weight ratio, two fractions were obtained: an oil

TECHNO-ECONOMIC ANALYSIS: PRELIMINARY ASSESSMENT OF PYROLYSIS OIL PRODUCTION COSTS AND MATERIAL ENERGY BALANCE ASSOCIATED WITH A TRANSPORTABLE FAST PYROLYSIS SYSTEM

Directory of Open Access Journals (Sweden)

Phil Badger

2011-02-01

Full Text Available A techno-economic analysis was performed for a 100 dry-ton/day (90,719 kg/day fast pyrolysis transportable plant. Renewable Oil International® LLC provided the life cycle cost of operating a 100 dry-ton/day fast pyrolysis system using southern pine wood chips as feedstock. Since data was not available from an actual large-scale plant, the study examined data obtained from an actual 15 dry-ton/day pilot plant and from several smaller plants. These data were used to obtain base figures to aid in the development of models to generate scaled-up costs for a larger 100 dry-ton/day facility. Bio-oil represented 60% of mass of product yield. The cost for the bio-oil from fast pyrolysis was valued at $0.94/gal. Energy cost bio-oil and char was valued at $6.35/MMBTU. Costs associated with purchasing feedstocks can drastically influence the final cost of the bio-oil. The assumed cost of feedstocks was $25/wet ton or $50/dry ton. This paper is part of a larger study investigating the economic and environmental impacts for producing bio-oil / biocide wood preservatives.

Properties and Beneficial Uses of (BioChars, with Special Attention to Products from Sewage Sludge Pyrolysis

Directory of Open Access Journals (Sweden)

Arianna Callegari

2018-03-01

Full Text Available Residual sludge disposal costs may constitute up to, and sometimes above, 50% of the total cost of operation of a Wastewater Treatment Plant (WWTP and contribute approximately 40% of the total greenhouse gas (GHG emissions associated with its operation. Traditionally, wastewater sludges are processed for: (a reduction of total weight and volume to facilitate their transfer and subsequent treatments; (b stabilization of contained organic material and destruction of pathogenic microorganisms, elimination of noxious odors, and reduction of putrefaction potential and, at an increasing degree; (c value addition by developing economically viable recovery of energy and residual constituents. Among several other processes, pyrolysis of sludge biomass is being experimented with by some researchers. From the process, oil with composition not dissimilar to that of biodiesels, syngas, and a solid residue can be obtained. While the advantage of obtaining sludge-derived liquid and gaseous fuels is obvious to most, the solid residue from the process, or char (also indicated as biochar by many, may also have several useful, initially unexpected applications. Recently, the char fraction is getting attention from the scientific community due to its potential to improve agricultural soils’ productivity, remediate contaminated soils, and supposed, possible mitigation effects on climate change. This paper first discusses sludge-pyrolysis-derived char production fundamentals (including relationships between char, bio-oil, and syngas fractions in different process operating conditions, general char properties, and possible beneficial uses. Then, based on current authors’ experiments with microwave-assisted sludge pyrolysis aimed at maximization of liquid fuel extraction, evaluate specific produced char characteristics and production to define its properties and most appropriate beneficial use applications in this type of setting.

Sulfur emission from Victorian brown coal under pyrolysis, oxy-fuel combustion and gasification conditions.

Science.gov (United States)

Chen, Luguang; Bhattacharya, Sankar

2013-02-05

Sulfur emission from a Victorian brown coal was quantitatively determined through controlled experiments in a continuously fed drop-tube furnace under three different atmospheres: pyrolysis, oxy-fuel combustion, and carbon dioxide gasification conditions. The species measured were H(2)S, SO(2), COS, CS(2), and more importantly SO(3). The temperature (873-1273 K) and gas environment effects on the sulfur species emission were investigated. The effect of residence time on the emission of those species was also assessed under oxy-fuel condition. The emission of the sulfur species depended on the reaction environment. H(2)S, SO(2), and CS(2) are the major species during pyrolysis, oxy-fuel, and gasification. Up to 10% of coal sulfur was found to be converted to SO(3) under oxy-fuel combustion, whereas SO(3) was undetectable during pyrolysis and gasification. The trend of the experimental results was qualitatively matched by thermodynamic predictions. The residence time had little effect on the release of those species. The release of sulfur oxides, in particular both SO(2) and SO(3), is considerably high during oxy-fuel combustion even though the sulfur content in Morwell coal is only 0.80%. Therefore, for Morwell coal utilization during oxy-fuel combustion, additional sulfur removal, or polishing systems will be required in order to avoid corrosion in the boiler and in the CO(2) separation units of the CO(2) capture systems.

Pyrolysis bio-oil upgrading to renewable fuels.

Science.gov (United States)

2014-01-01

This study aims to upgrade woody biomass pyrolysis bio-oil into transportation fuels by catalytic hydrodeoxygenation : (HDO) using nanospring (NS) supported catalyst via the following research objectives: (1) develop nanospring-based : catalysts (nan...

Waste processing by pyrolysis; Posibilidades de la pirolisis en el tratamiento de los residuos

Energy Technology Data Exchange (ETDEWEB)

Elias, X.

2002-07-01

The present work starts reminding the beginnings of pyrolysis and its applications. Nevertheless the Directive 2000/76/CE talks about it and gasification calling them intermediate systems for waste to energy. Of all it, the conclusions is that both gasification and particularly pyrolysis alone cannot solve the environmental challenges that the treatment of the present waste supposes. Thus it is precise to refer to a larger set of technologies. Of the industrial applications it is inferred that both gasification and pyrolysis generate a minimum amount of gases, in comparison with the conventional incineration, so they are more advanced technologies of treatment. Pyrolysis allows a larger treatment of waste because, depending on an organic/inorganic relation present in the waste, provides a better fitting to the treatment. (Author)

Biomass pyrolysis liquid to citric acid via 2-step bioconversion.

Science.gov (United States)

Yang, Zhiguang; Bai, Zhihui; Sun, Hongyan; Yu, Zhisheng; Li, Xingxing; Guo, Yifei; Zhang, Hongxun

2014-12-31

The use of fossil carbon sources for fuels and petrochemicals has serious impacts on our environment and is unable to meet the demand in the future. A promising and sustainable alternative is to substitute fossil carbon sources with microbial cell factories converting lignocellulosic biomass into desirable value added products. However, such bioprocesses require tolerance to inhibitory compounds generated during pretreatment of biomass. In this study, the process of sequential two-step bio-conversion of biomass pyrolysis liquid containing levoglucosan (LG) to citric acid without chemical detoxification has been explored, which can greatly improve the utilization efficiency of lignocellulosic biomass. The sequential two-step bio-conversion of corn stover pyrolysis liquid to citric acid has been established. The first step conversion by Phanerochaete chrysosporium (P. chrysosporium) is desirable to decrease the content of other compounds except levoglucosan as a pretreatment for the second conversion. The remaining levoglucosan in solution was further converted into citric acid by Aspergillus niger (A. niger) CBX-209. Thus the conversion of cellulose to citric acid is completed by both pyrolysis and bio-conversion technology. Under experimental conditions, levoglucosan yield is 12% based on the feedstock and the citric acid yield can reach 82.1% based on the levoglucosan content in the pyrolysis liquid (namely 82.1 g of citric acid per 100 g of levoglucosan). The study shows that P. chrysosporium and A. niger have the potential to be used as production platforms for value-added products from pyrolyzed lignocellulosic biomass. Selected P. chrysosporium is able to decrease the content of other compounds except levoglucosan and levoglucosan can be further converted into citric acid in the residual liquids by A. niger. Thus the conversion of cellulose to citric acid is completed by both pyrolysis and bio-conversion technology.

A novel approach of solid waste management via aromatization using multiphase catalytic pyrolysis of waste polyethylene.

Science.gov (United States)

Gaurh, Pramendra; Pramanik, Hiralal

2018-01-01

A new and innovative approach was adopted to increase the yield of aromatics like, benzene, toluene and xylene (BTX) in the catalytic pyrolysis of waste polyethylene (PE). The BTX content was significantly increased due to effective interaction between catalystZSM-5 and target molecules i.e., lower paraffins within the reactor. The thermal and catalytic pyrolysis both were performed in a specially designed semi-batch reactor at the temperature range of 500 °C-800 °C. Catalytic pyrolysis were performed in three different phases within the reactor batch by batch systematically, keeping the catalyst in A type- vapor phase, B type- liquid phase and C type- vapor and liquid phase (multiphase), respectively. Total aromatics (BTX) of 6.54 wt% was obtained for thermal pyrolysis at a temperature of 700 °C. In contrary, for the catalytic pyrolysis A, B and C types reactor arrangement, the aromatic (BTX) contents were progressively increased, nearly 6 times from 6.54 wt% (thermal pyrolysis) to 35.06 wt% for C-type/multiphase (liquid and vapor phase). The pyrolysis oil were characterized using GC-FID, FT-IR, ASTM distillation and carbon residue test to evaluate its end use and aromatic content. Copyright © 2017 Elsevier Ltd. All rights reserved.

Novel technique for coal pyrolysis and hydrogenation product analysis. Quarterly report, June 1, 1992

Energy Technology Data Exchange (ETDEWEB)

Pfefferle, L.D.

1992-12-31