Effect of operating temperature on LMFBR core performance

International Nuclear Information System (INIS)

Noyes, R.C.; Bergeron, R.J.; di Lauro, G.F.; Kulwich, M.R.; Stuteville, D.W.

1977-01-01

The purpose of the study is to provide an engineering evaluation of high and low temperature LMFBR core designs. The study was conducted by C-E supported by HEDL expertise in the areas of materials behavior, fuel performance and fabrication/fuel cycle cost. The evaluation is based primarily on designs and analyses prepared by AI, GE and WARD during Phase I of the PLBR studies

Fluid structure interaction in LMFBR cores modelling by an homogenization method

International Nuclear Information System (INIS)

Brochard, D.

1988-01-01

The upper plenum of the internals of PWR, the steam generator bundle, the nuclear reactor core, may be schematically represented by a beam bundle immersed in a fluid. The dynamical study of such a system needs to take into account fluid structure interaction. A refined model at the scale of the tubes can be used but leads to a very difficult problem to solve even on the largest computers. The homogenization method allows to have an approximation of the fluid structure interaction for the global behaviour of the bundle. It consists of replacing the heterogeneous physical medium (tubes and fluid) by an equivalent homogeneous medium whose characteristics are determined from the resolution of a set of problems on the elementary cell. The aim of this paper is to present the main steps of the determination of this equivalent medium in the case of small displacements (acoustic behaviour of the fluid). Then an application to LMFBR core geometry has been realised, which shows the lowering effect on eigenfrequencies due to the fluid. Some comparisons with test results will be presented. 6 refs, 7 figs, 2 tabs

A study on reactor core failure thresholds to safety operation of LMFBR

International Nuclear Information System (INIS)

Kazuo, Haga; Hiroshi, Endo; Tomoko, Ishizu; Yoshihisa, Shindo

2006-01-01

Japan Nuclear Safety Organization (JNES) has been developing the methodology and computer codes for applying level-1 PSA to LMFBR. Many of our efforts have been directed to the judging conditions of reactor core damage and the time allowed to initiate the accident management. Several candidates of the reactor core failure threshold were examined to a typical proto-type LMFBR with MOX fuel based on the plant thermal-hydraulic analyses to the actual progressions leading to the core damage. The results of the present study showed that the judging condition of coolant-boundary integrity failure, 750 degree-C of the boundary temperature, is enough as the threshold of core damage to PLOHS (protected loss-of-heat sink). High-temperature fuel cladding creep failure will not take place before the coolant-boundary reaches the judging temperature and sodium boiling will not occur due to the system pressure rise. In cases of ATWS (anticipated transient without scrum) the accident progression is so fast and the reactor core damage will be inevitable even a realistic negative reactivity insertion due to the temperature rise is considered. Only in the case of ULOHS (unprotected loss-of-heat sink) a relatively long time of 11 min will be allowed till the shut-down of the reactor before the core damage. (authors)

Model-based temperature noise monitoring methods for LMFBR core anomaly detection

International Nuclear Information System (INIS)

Tamaoki, Tetsuo; Sonoda, Yukio; Sato, Masuo; Takahashi, Ryoichi.

1994-01-01

Temperature noise, measured by thermocouples mounted at each core fuel subassembly, is considered to be the most useful signal for detecting and locating local cooling anomalies in an LMFBR core. However, the core outlet temperature noise contains background noise due to fluctuations in the operating parameters including reactor power. It is therefore necessary to reduce this background noise for highly sensitive anomaly detection by subtracting predictable components from the measured signal. In the present study, both a physical model and an autoregressive model were applied to noise data measured in the experimental fast reactor JOYO. The results indicate that the autoregressive model has a higher precision than the physical model in background noise prediction. Based on these results, an 'autoregressive model modification method' is proposed, in which a temporary autoregressive model is generated by interpolation or extrapolation of reference models identified under a small number of different operating conditions. The generated autoregressive model has shown sufficient precision over a wide range of reactor power in applications to artificial noise data produced by an LMFBR noise simulator even when the coolant flow rate was changed to keep a constant power-to-flow ratio. (author)

Seismic behaviour of LMFBR reactor cores. The SYMPHONY program

International Nuclear Information System (INIS)

Broc, Daniel

2001-01-01

As part of a comprehensive program on the seismic behaviour of the LMFBR reactor cores, the SYMPHONY experimental program, performed at the CEA Saclay, is carried out from 1993 up to now. LMFBR reactor cores are composed of fuel assemblies and neutronic shields, immersed in sodium (the primary coolant) or water (for the experimental tests). The main objective of the seismic studies is to evaluate the assembly motions, with consequences on the reactivity and the control rod insertability, and to verify the structural integrity of the assemblies under the impact forces. The experimental program has reached its objectives. Tests have been performed in a satisfying way. Instrumentation allowed to collect displacements, accelerations, and shock forces. All the results constitute a comprehensive base of valuable and reliable data. The interpretation of the tests is based on beam models, taking into account the Fluid Structure Interaction, and the shocks between the assemblies. Theoretical results are in a quite good agreement with the experimental ones. The interpretation of the hexagonal tests in water pointed out very strong coupling between the assemblies and lead to the development of a specific Fluid Structure Interaction, taking into account not only inertial effects, but dissipative effects also. (author)

Development of concept and neutronic calculation method for large LMFBR core

International Nuclear Information System (INIS)

Shirakata, K.; Ishikawa, M.; Ikegami, T.; Sanda, T.; Kaneto, K.; Kawashima, M.; Kaise, Y.; Shirakawa, M.; Hibi, K.

1991-01-01

Presented in this paper is the state of the art of reactor physics R and Ds for the development of concept and neutronic calculation method for large Liquid Metal Fast Breeder Reactor (LMFBR) core. Physics characteristics of concepts for mixed oxide (MOX) fueled large FBR core were investigated by a series of benchmark critical experiments. Next, an adequacy and accuracy of the current neutronic calculation method was assessed by the experiments analyses, and then neutronic prediction accuracies by the method were evaluated for physics characteristics of the large core. Concerns on core development were discussed in terms of neutronics. (author)

SASSYS LMFBR systems analysis code

International Nuclear Information System (INIS)

Dunn, F.E.; Prohammer, F.G.

1982-01-01

The SASSYS code provides detailed steady-state and transient thermal-hydraulic analyses of the reactor core, inlet and outlet coolant plenums, primary and intermediate heat-removal systems, steam generators, and emergency shut-down heat removal systems in liquid-metal-cooled fast-breeder reactors (LMFBRs). The main purpose of the code is to analyze the consequences of failures in the shut-down heat-removal system and to determine whether this system can perform its mission adequately even with some of its components inoperable. The code is not plant-specific. It is intended for use with any LMFBR, using either a loop or a pool design, a once-through steam generator or an evaporator-superheater combination, and either a homogeneous core or a heterogeneous core with internal-blanket assemblies

Experimental studies of 350 Mw(e) heterogeneous LMFBR cores at ZPPR

International Nuclear Information System (INIS)

Collins, P.J.; McFarlane, H.F.; Beck, C.L.; Lineberry, M.J.; Carpenter, S.G.; Ducat, G.A.; Gasidlo, J.M.; Goin, R.W.

1979-01-01

The annular heterogeneous concept has been adopted for the Clinch River Breeder Reactor. To provide verification of design and safety analysis, fourteen core configurations were studied at ZPPR. The results and analysis of the early assemblies, ZPPR-7A, 7B, and 7C, have been previously reported and only the more significant conclusions are summarized here. Later assemblies, 7D to 7H, were designed to provide data on variations of control rod and internal blanket arrangements. Assemblies 8A to 8E provided data on the replacement of uranium by thorium in various blanket subassemblies

LMFBR in-core thermal-hydraulics: the state of the art and US research and development needs

International Nuclear Information System (INIS)

Khan, E.U.

1980-04-01

A detailed critical review is presented of the literature relevant to predicting coolant flow and temperature fields in LMFBR core assemblies for nominal and non-nominal rod bundle geometries and reactor operating conditions. The review covers existing thermal-hydraulic models, computational methods, and experimental data useful for the design of an LMFBR core. The literature search made for this review included publications listed by Nuclear Science Abstracts and Energy Data Base as well as papers presented at key nuclear conferences. Based on this extensive review, the report discusses the accuracy with which the models predict flow and temperature fields in rod assemblies, identifying areas where analytical, experimental, and model development needs exist

Review of pertinent thermal-hydraulic data for LMFBR core natural circulation analyses

International Nuclear Information System (INIS)

Bishop, A.A.; Coffield, R.D. Jr.; Markley, R.A.

1980-01-01

A literature review and summary of significant data is presented relative to LMFBR core natural convection cooling analysis. First, a brief review of computer codes and respective input data needs is made, significant data areas are then addressed and data for verifying the code calculations are described. Recommendations and conclusions with regard to the data are included

SUPERENERGY-2: a multiassembly, steady-state computer code for LMFBR core thermal-hydraulic analysis

Energy Technology Data Exchange (ETDEWEB)

Basehore, K.L.; Todreas, N.E.

1980-08-01

Core thermal-hydraulic design and performance analyses for Liquid Metal Fast Breeder Reactors (LMFBRs) require repeated detailed multiassembly calculations to determine radial temperature profiles and subchannel outlet temperatures for various core configurations and subassembly structural analyses. At steady-state, detailed core-wide temperature profiles are required for core restraint calculations and subassembly structural analysis. In addition, sodium outlet temperatures are routinely needed for each reactor operating cycle. The SUPERENERGY-2 thermal-hydraulic code was designed specifically to meet these designer needs. It is applicable only to steady-state, forced-convection flow in LMFBR core geometries.

SUPERENERGY-2: a multiassembly, steady-state computer code for LMFBR core thermal-hydraulic analysis

International Nuclear Information System (INIS)

Basehore, K.L.; Todreas, N.E.

1980-08-01

Core thermal-hydraulic design and performance analyses for Liquid Metal Fast Breeder Reactors (LMFBRs) require repeated detailed multiassembly calculations to determine radial temperature profiles and subchannel outlet temperatures for various core configurations and subassembly structural analyses. At steady-state, detailed core-wide temperature profiles are required for core restraint calculations and subassembly structural analysis. In addition, sodium outlet temperatures are routinely needed for each reactor operating cycle. The SUPERENERGY-2 thermal-hydraulic code was designed specifically to meet these designer needs. It is applicable only to steady-state, forced-convection flow in LMFBR core geometries

Analysis of hypothetical LMFBR whole-core accidents in the USA

International Nuclear Information System (INIS)

Ferguson, D.R.; Deitrich, L.W.; Brown, N.W.; Waltar, A.E.

1978-01-01

The issue of hypothetical whole-core accidents continues to play a significant role in assessment of the potential risk to the public associated with LMFBR operation in the USA. The paper briefly characterizes the changing nature of this role, with emphasis on the current risk-oriented perspective. It then describes the models and codes used for accident analysis in the USA which have been developed under DOE sponsorship and summarizes some specific applications of the codes to the current generation of fast reactors. An assessment of future trends in this area concludes the paper

SIMMER-I: an S/sub n/, Implicit, Multifield, Multicomponent, Eulerian, Recriticality code for LMFBR disrupted core analysis

International Nuclear Information System (INIS)

Bell, C.R.; Bleiweis, P.B.; Boudreau, J.E.; Parker, F.R.; Smith, L.L.

1976-08-01

Physical models, numerical methods, and program description are presented for SIMMER-I, a computer program which predicts the neutronic and fluid dynamic behavior of an LMFBR during a hypothetical core disruptive accident

Damping of the radial impulsive motion of LMFBR core components separated by fluid squeeze films

International Nuclear Information System (INIS)

Liebe, R.; Zehlein, H.

1977-01-01

The core deformation of a liquid metal cooled fast breeder reactor (LMFBR) due to local pressure propagation from rapid energy releases is a complex three-dimensional fluid-structure-interaction problem. High pressure transients of short duration cause structural deformation of the closely spaced fuel elements, which are surrounded by the flowing coolant. Corresponding relative displacements give rise to squeezing fluid motion in the thin layers between the subassemblies. Therefore significant backpressures are produced and the resulting time and space dependent fluid forces are acting on the structure as additional non-conservative external loads. Realistic LMFBR safety analysis of several clustered fuel elements have to account for such flow induced forces. Several idealized models have been proposed to study some aspects of the complex problem. As part of the core mechanics activities at GfK Karlsruhe this paper describes two fluid flow models (model A, model B), which are shown to be suitable for physically coupled fluid-structure analyses. Important assumptions are discussed in both cases and basic equations are derived for one- and two-dimensional incompressible flow fields. The interface of corresponing computer codes FLUF (model A) and FLOWAX (model B) with structural dynamics programs is outlined. Finally fluid-structure interaction problems relevant to LMFBR design are analyzed; parametric studies indicate a significant cushioning effect, energy dissipation and a strongly nonlinear as well as timedependent damping of the structural response. (Auth.)

Emergency core cooling system for LMFBR type reactors

International Nuclear Information System (INIS)

Tamano, Toyomi; Fukutomi, Shigeki.

1980-01-01

Purpose: To enable elimination of decay heat in an LMFBR type reactor by securing natural cycling force in any state and securing reactor core cooling capacity even when both an external power supply and an emergency power supply are failed in emergency case. Method: Heat insulating material portion for surrounding a descent tube of a steam drum provided at high position for obtaining necessary flow rate for flowing resistance is removed from heat transmitting surface of a recycling type steam generator to provide a heat sink. That is, when both an external power supply and an emergency power supply are failed in emergency, the heat insulator at part of a steam generator recycling loop is removed to produce natural cycling force between it and the heat transmitting portion of the steam generator as a heat source for the heat sink so as to secure the flow rate of the recycling loop. When the power supply is failed in emergency, the heat removing capacity of the steam generator is secured so as to remove the decay heat produced in the reactor core. (Yoshihara, H.)

54Mn release from LMFBR cores

International Nuclear Information System (INIS)

Polley, M.V.

1976-10-01

The inventory of 54 Mn per unit exposed area of stainless steel in LMFBR cores may be calculated using a formula originally derived at HEDL. This treats the simultaneous production by activation and release by corrosion and diffusion of 54 Mn and assumes that the concentration at the steel surface is zero. The inventory per unit exposed area is calculated as a function of temperature and is compared with that calculated simply by assuming stoichiometric corrosion. An effective diffusion coefficient is used in the calculations which include contributions from both lattice and grain boundary diffusion. A general relationship is derived for the effective diffusion coefficient and it is shown how values may be obtained using the Levine-MacCallum and the Fisher theories of grain boundary diffusion. Values of the lattice diffusion coefficient were obtained by analysing data obtained from sodium loop experiments. The effect on the inventory due to the possible formation of a ferrite layers on the exposed surface is discussed and it is also shown how the inventory over several fuel cycles may be calculated. (U.K.)

An internal core catcher for a pool L.M.F.B.R. and connected studies

International Nuclear Information System (INIS)

Le Rigoleur, C.; Kayser, G.

1979-01-01

This paper describes an internal core catcher for a pool LMFBR. Problems related to retention of debris are studied: downward progression of debris from the core to the core catcher, debris bed formation, heat transfer below the core catcher plate and to the main vessel, mechanical resistance. These results are used to estimate the performances of the internal core catcher for a given core melt-down-accident. It is seen that for a uniform thickness layer on the core catcher the retention capabilities are satisfactory. Then the problem of a heap of debris is approached. Dryout is studied. Uncertainties related to the bed characteristics and problems of extended dryout beds are put forward

SASSYS LMFBR systems code

International Nuclear Information System (INIS)

Dunn, F.E.; Prohammer, F.G.; Weber, D.P.

1983-01-01

The SASSYS LMFBR systems analysis code is being developed mainly to analyze the behavior of the shut-down heat-removal system and the consequences of failures in the system, although it is also capable of analyzing a wide range of transients, from mild operational transients through more severe transients leading to sodium boiling in the core and possible melting of clad and fuel. The code includes a detailed SAS4A multi-channel core treatment plus a general thermal-hydraulic treatment of the primary and intermediate heat-transport loops and the steam generators. The code can handle any LMFBR design, loop or pool, with an arbitrary arrangement of components. The code is fast running: usually faster than real time

Neutronic feasibility of an LMFBR super long-life core (SLLC)

International Nuclear Information System (INIS)

Kawashima, Masatoshi; Aoki, Katsutada; Arie, Kazuo; Tsuboi, Yasushi

1988-01-01

The LMFBR Super Long-Life Core (SLLC) concept has evolved over the last few years as one of the targets of innovative approaches for future FBR cost reduction. An idea for SLLC has been developed wherein the core lifetime is extended up to the plant life of about 30 years by applying the radially and axially multi-zoned core concept (the improved homogeneous core concept). The main purpose of the present study is placed on the evaluation of neutronic feasibility of the 1000 MWe class SLLC concept. The core size of the present SLLC, which is approximately 3 to 4 times as large as those of the current 1000 MWe core design, was determined by the limit of the maximum fast neutron fluence level, which was tentatively assumed to be 5-6x10 23 nvt as the target of the future development of advanced cladding materials. Emphasis is placed on the discussion of neutronic performances of cores with oxide fuels rather than metal or carbide fuels. The present study has shown that proper zoning of the different plutonium enrichment fuels at the initial core makes it possible to achieve small enough reactivity loss during 30-year burnup while satisfying mild variation of the subassembly power distributions using a higher fuel volume fraction of about 50%. Effects of important neutronic parameters on the core performances are also discussed. (orig.)

Structural and containment response to LMFBR accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.; Fistedis, S.H.; Baker, L. Jr.; Stepnewski, D.D.; Peak, R.D.; Gluekler, E.L.

1978-01-01

The results of current developments in analysing the response of reactor structures and containment to LMFBR accidents are presented. The current status of analysis of the structural response of LMFBR's to core disruptive accidents, including head response, potential missile generation and the effects of internal structures are presented. The results of recent experiments to help clarify the thermal response of reactor structures to molten core debris are summarized, including the use of this data to calculate the response of the secondary containment. (author)

Bulk coolant cavitation in LMFBR containment loading following a whole-core explosion

International Nuclear Information System (INIS)

Jones, A.V.

1977-01-01

An LMFBR core undergoing an explosion transmits energy to the containment in a series of pressure waves and the containment loading is determined by their cumulative effect. These pressure waves are modified by their interaction with the coolant through which they propagate. It is necessary to model both the induction of bulk cavitation by tension waves and the interaction of pressure waves with cavitated liquid in realistic containment loading calculations. This paper sets out the progress which has been achieved in such modelling and first indications for the effect of bulk coolant cavitation in LMFBR containment loading. Conclusions may be briefly summarised: 1) Bulk cavitation must be included in realistic containment loading calculations. 2) Phenomenological models of cavitated liquid without memory are inappropriate. The best approach is to model bubble dynamics directly, including at least momentum conservation and surface tension. 3) The containment loading resulting from a given explosion is sensitive to the state of preparation of the coolant. The number density of nucleation sites should therfore accompany the results of model tests. (Auth.)

Seismic analysis methods for LMFBR core and verification with mock-up vibration tests

International Nuclear Information System (INIS)

Sasaki, Y.; Kobayashi, T.; Fujimoto, S.

1988-01-01

This paper deals with the vibration behaviors of a cluster of core elements with the hexagonal cross section in a barrel under the dynamic excitation due to seismic events. When a strong earthquake excitation is applied to the core support, the cluster of core elements displace to a geometrical limit determined by restraint rings in the barrel, and collisions could occur between adjacent elements as a result of their relative motion. For these reasons, seismic analysis on LMFBR core elements is a complicated non-linear vibration problem, which includes collisions and fluid interactions. In an actual core design, it is hard to include hundreds of elements in the numerical calculations. In order to study the seismic behaviors of core elements, experiments with single row 29 elements (17 core fuel assemblies, 4 radial blanket assemblies, and 8 neutron shield assemblies) simulated all elements in MONJU core central row, and experiments with 7 cluster rows of 37 core fuel assemblies in the core center were performed in a fluid filled tank, using a large-sized shaking table. Moreover, the numerical analyses of these experiments were performed for the validation of simplified and detailed analytical methods. 4 refs, 18 figs

Heterogeneous gas core reactor

International Nuclear Information System (INIS)

Han, K.I.

1977-01-01

Preliminary investigations of a heterogeneous gas core reactor (HGCR) concept suggest that this potential power reactor offers distinct advantages over other existing or conceptual reactor power plants. One of the most favorable features of the HGCR is the flexibility of the power producing system which allows it to be efficiently designed to conform to a desired optimum condition without major conceptual changes. The arrangement of bundles of moderator/coolant channels in a fissionable gas or mixture of gases makes a truly heterogeneous nuclear reactor core. It is this full heterogeneity for a gas-fueled reactor core which accounts for the novelty of the heterogeneous gas core reactor concept and leads to noted significant advantages over previous gas core systems with respect to neutron and fuel economy, power density, and heat transfer characteristics. The purpose of this work is to provide an insight into the design, operating characteristics, and safety of a heterogeneous gas core reactor system. The studies consist mainly of neutronic, energetic and kinetic analyses of the power producing and conversion systems as a preliminary assessment of the heterogeneous gas core reactor concept and basic design. The results of the conducted research indicate a high potential for the heterogeneous gas core reactor system as an electrical power generating unit (either large or small), with an overall efficiency as high as 40 to 45%. The HGCR system is found to be stable and safe, under the conditions imposed upon the analyses conducted in this work, due to the inherent safety of ann expanding gaseous fuel and the intrinsic feedback effects of the gas and water coolant

CEC activities in the field of LMFBR safety

International Nuclear Information System (INIS)

Balz, W.; Finzi, S.; Klersy, R.

1976-01-01

The aim of the ECC is to reach a common LMFBR Safety strategy in Europe. To this end the Commission promotes collaboration between the different fast reactor projects in the Community through working groups and collaborative arrangements and contributes with a research activity executed in its Joint Research Centre Ispra. A short description is given of the activity in the working groups and of the Ispra programme on LMFBR Safety. This programme covers: LMFBR thermohydraulics, fuel coolant interactions, dynamic structure loading and response, safety related material properties and whole core accident code development

Finite element program ARKAS: verification for IAEA benchmark problem analysis on core-wide mechanical analysis of LMFBR cores

International Nuclear Information System (INIS)

Nakagawa, M.; Tsuboi, Y.

1990-01-01

''ARKAS'' code verification, with the problems set in the International Working Group on Fast Reactors (IWGFR) Coordinated Research Programme (CRP) on the inter-comparison between liquid metal cooled fast breeder reactor (LMFBR) Core Mechanics Codes, is discussed. The CRP was co-ordinated by the IWGFR around problems set by Dr. R.G. Anderson (UKAEA) and arose from the IWGFR specialists' meeting on The Predictions and Experience of Core Distortion Behaviour (ref. 2). The problems for the verification (''code against code'') and validation (''code against experiment'') were set and calculated by eleven core mechanics codes from nine countries. All the problems have been completed and were solved with the core structural mechanics code ARKAS. Predictions by ARKAS agreed very well with other solutions for the well-defined verification problems. For the validation problems based on Japanese ex-reactor 2-D thermo-elastic experiments, the agreements between measured and calculated values were fairly good. This paper briefly describes the numerical model of the ARKAS code, and discusses some typical results. (author)

LMFBR accident delineation study: approach and preliminary results

International Nuclear Information System (INIS)

Williams, D.C.; Sholtis, J.A.; Rios, M.; Worledge, D.H.; Conrad, P.W.; Varela, D.W.; Pickard, P.S.

1979-01-01

Event trees have been constructed for all phases of LMFBR accidents. The trees proved useful for identifying meaningful initiating accident categories and containment responses. In these areas, quantification appears feasible, given an adequate data base. Event trees were also used to represent in-core phenomenological questions governing accident progression and energetics, but here quantification appears impracticable because pervasive phenomenological uncertainties exist. Infrequent accident initiation is the dominant factor in assuring low risk. Nevertheless, containment promises an additional measure of risk reduction provided severe energetics are highly unlikely. The delineation served to systematize LMFBR safety issues and should aid in evaluating LMFBR R and D priorities

Effect of reactor size on the breeding economics of LMFBR blankets

International Nuclear Information System (INIS)

Tagishi, A.; Driscoll, M.J.

1975-02-01

The effect of reactor size on the neutronic and economic performance of LMFBR blankets driven by radially-power-flattened cores has been investigated using both simple models and state-of-the-art computer methods. Reactor power ratings in the range 250 to 3000 MW(e) were considered. Correlations for economic breakeven and optimum irradiation times and blanket thicknesses have been developed for batch-irradiated blankets. It is shown that a given distance from the core-blanket interface the fissile buildup rate per unit volume remains very nearly constant in the radial blanket as (radially-power-flattened, constant-height) core size increases. As a consequence, annual revenue per blanket assembly, and breakeven and optimum irradiation times and optimum blanket dimensions, are the same for all reactor sizes. It is also shown that the peripheral core fissile enrichment, hence neutron leakage spectra, of the (radially-power-flattened, constant-height) cores remains essentially constant as core size increases. Coupled with the preceding observations, this insures that radial blanket breeding performance in demonstration-size LMFBR units will be a good measure of that in much larger commercial LMFBR's

LMFBR fuel analysis. Task A: oxide fuel dynamics. Final report, October 1977--September 1978

International Nuclear Information System (INIS)

Dhir, V.K.; Frank, M.; Kastenberg, W.E.; McKone, T.E.

1979-03-01

Three aspects of LMFBR safety are discussed. The first concerns the potential reactivity effects of whole core fuel motion prior to pin failure in low ramp rate transient overpower accidents. The second concerns the effects of flow blockages following pin failure on the coolability of a core following an unprotected overpower transient. The third aspect concerns the safety related implications of using thorium based fuels in LMFBR's

Bubble behavior in LMFBR core disruptive accidents. Annual report, June 1, 1975--June 30, 1976

International Nuclear Information System (INIS)

Reynolds, A.B.; Erdman, C.A.; Garner, P.L.; Kennedy, M.F.; Rao, S.P.; Refling, J.G.

1976-08-01

The work reported here is part of the Aerosol Release and Transport program for LMFBR safety assessment for the Reactor Safety Research Division of the U.S. Nuclear Regulatory Commission. Six areas were at various stages of investigation during this reporting period. A study of nonequilibrium mass transfer during fuel expansion and a study of the dynamics of fuel expansion into the sodium pool were completed. Studies are underway on condensation on above-core structures and on generation of aerosols from condensation. Studies were initiated on small-particle generation from hydrodynamic fragmentation, on particle kinematics and on particle-surface interaction

Attenuation of airborne debris from LMFBR accidents

International Nuclear Information System (INIS)

Morewitz, H.A.; Johnson, R.P.; Nelson, C.T.; Vaughan, E.U.; Guderjahn, C.A.; Hilliard, R.K.; McCormack, J.D.; Postma, A.K.

1978-01-01

Experimental and theoretical studies have been performed to characterize the behavior of airborne particulates (aerosols) expected to be produced by hypothetical core disassembly accidents (HCDA's) in liquid metal fast breeder reactors (LMFBR's). These aerosol studies include work on aerosol transport in a 20-m high, 850-m 3 closed vessel at moderate concentrations; aerosol transport in a small vessel under conditions of high concentration (approximately 1,000 g/m 3 ), high turbulence, and high temperature (approximately 2000 0 C); and aerosol transport through various leak paths. These studies have shown that tittle, if any, airborne debris from LMFBR HCDA's would reach the atmosphere exterior to an intact reactor containment building. (author)

Liquid-metal fast-breeder reactors: Preliminary safety and environmental information document. Volume VI

International Nuclear Information System (INIS)

1980-01-01

Information is presented concerning LMFBR design characteristics; uranium-plutonium/uranium recycle homogeneous core; uranium-plutonium/uranium spiked recycle heterogeneous core; uranium-plutonium/uranium spiked recycle homogeneous core; uranium-plutonium/thorium spiked recycle heterogeneous core; uranium-plutonium/thorium spiked recycle homogeneous core; thorium-plutonium/thorium spiked recycle homogeneous core; denatured uranium-233/thorium cycle homogeneous core; safety consideration for the LMFBR; and environmental considerations

Overview of core designs and requirements/criteria for core restraint systems

International Nuclear Information System (INIS)

Sutherland, W.H.

1984-09-01

The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System are presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented

Acoustics and voiding dynamics during SLSF simulations of LMFBR undercooling transients

International Nuclear Information System (INIS)

Anderson, T.T.; Kuzay, T.M.; Marr, W.W.; Miles, K.J.; Pedersen, D.R.; Thompson, D.H.; Wilson, R.E.

1978-01-01

The SLSF is the largest U.S. in-reactor test vehicle for steady-state and transient experiments in an environment typical of a LMFBR core. The SLSF experiment program, sponsored by the Department of Energy, contributes to the LMFBR safety assurance program by providing data on key phenomena that occur during postulated reactor accidents. This paper describes completed SLSF experiments, in-core instrumentation used, and methods of data interpretation to determine sodium boiling and voiding dynamics. Boiling inception is shown to be identifiable from several types of in-core instruments. Location of the boiling front and void growth derived from experimental data are compared with analytical predictions. These and other data form the basis to improve understanding of accidents and to validate or guide the development of accident analysis methods

Overview of core designs and requirements/criteria for core restraint systems

International Nuclear Information System (INIS)

Sutherland, W.H.

1984-01-01

The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System is presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented. (author)

LMFBR Blanket Physics Project progress report No. 2

International Nuclear Information System (INIS)

Forbes, I.A.; Driscoll, M.J.; Rasmussen, N.C.; Lanning, D.D.; Kaplan, I.

1971-01-01

This is the second annual report of an experimental program for the investigation of the neutronics of benchmark mock-ups of LMFBR blankets. Work was devoted primarily to measurements on Blanket Mock-Up No. 2, a simulation of a typical large LMFBR radial blanket and its steel reflector. Activation traverses and neutron spectra were measured in the blanket; calculations of activities and spectra were made for comparison with the measured data. The heterogeneous self-shielding effect for 238 U capture was found to be the most important factor affecting the comparison. Optimization and economic studies were made which indicate that the use of a high-albedo reflector material such as BeO or graphite may improve blanket neutronics and economics

Heterogeneous cores for fast breeder reactor

International Nuclear Information System (INIS)

Schroeder, R.; Spenke, H.

1980-01-01

Firstly, the motivation for heterogeneous cores is discussed. This is followed by an outline of two reactor designs, both of which are variants of the combined ring and island core. These designs are presented by means of figures and detailed tables. Subsequently, a description of two international projects at fast critical zero energy facilities is given. Both of them support the nuclear design of heterogeneous cores. In addition to a survey of these projects, a typical experiment is discussed: the measurement of rate distributions. (orig.) [de

Review of advanced core designs for LMFBRs

International Nuclear Information System (INIS)

Yoshida, Kazuo

1986-01-01

It is a matter of great importance for the development of LMFBR to reduce its power cost to the level of the other power generating means. For this purpose, some ideas that use advanced core concepts to reduce LMFBR's power cost by improving its fuel cycle economics have recently been proposed. In this report, two hopeful ideas that use advanced core concepts: (1) Ultra Long Life Core (ULLC) - non-refueling over LMFBR power plant life; (2) Integral Fast Reactor (IFR) concept - metal fueled core and pyrometallurgical reprocessing; are picked up and their economical effect and technical probrems are investigated. (author)

Studies of LMFBR: method of analysis and some results

International Nuclear Information System (INIS)

Ishiguro, Y.; Dias, A.F.; Nascimento, J.A. do.

1983-01-01

Some results of recent studies of LMFBR characteristics are summarized. A two-dimensional model of the LMFBR is taken from a publication and used as the base model for the analysis. Axial structures are added to the base model and a three-dimensional (Δ - Z) calculation has been done. Two dimensional (Δ and RZ) calculations are compared with the three-dimensional and published results. The eigenvalue, flux and power distributions, breeding characteristics, control rod worth, sodium-void and Doppler reactivities are analysed. Calculations are done by CITATION using six-group cross sections collapsed regionwise by EXPANDA in one-dimensional geometries from the 70-group JFS library. Burnup calculations of a simplified thorium-cycle LMFBR have also been done in the RZ geometry. Principal results of the studies are: (1) the JFS library appears adequate for predicting overall characteristics of an LMFBR, (2) the sodium void reactivity is negative within - 25 cm from the outer boundary of the core, (3) the halflife of Pa-233 must be considered explicitly in burnup analyses, and (4) two-dimensional (RZ and Δ) calculations can be used iteratively to analyze three-dimensional reactor systems. (Author) [pt

Neutronic analysis of LMFBRs during severe core disruptive accidents

International Nuclear Information System (INIS)

Tomlinson, E.T.

1979-01-01

A number of numerical experiments were performed to assess the validity of diffusion theory and various perturbation methods for calculating the reactivity state of a severely disrupted liquid metal cooled fast breeder reactor (LMFBR). The disrupted configurations correspond, in general, to phases through which an LMFBR core could pass during a core disruptive accident (CDA). Two-reactor models were chosen for this study, the two zone, homogeneous Clinch River Breeder Reactor and the Large Heterogeneous Reactor Design Study Core. The various phases were chosen to approximate the CDA results predicted by the safety analysis code SAS3D. The calculational methods investigated in this study include the eigenvalue difference technique based on both discrete ordinate transport theory and diffusion theory, first-order perturbation theory, exact perturbation theory, and a new hybrid perturbation theory. Selected cases were analyzed using Monte Carlo methods. It was found that in all cases, diffusion theory and perturbation theory yielded results for the change in reactivity that significantly disagreed with both the discrete ordinate and Monte Carlo results. These differences were, in most cases, in a nonconservative direction

Fission-gas bubble modeling for LMFBR accidents

International Nuclear Information System (INIS)

Ostensen, R.W.

1977-01-01

The behavior of fission-gas bubbles in unrestructured oxide fuel can have a dominant effect on the course of a core disruptive accident in an LMFBR. The paper describes a simplified model of bubble behavior and presents results of that model in analyzing the relevant physical assumptions and predicting gas behavior in molten fuel

Qualification testing program plan for SIMMER. A computer code for LMFBR disrupted core analysis

International Nuclear Information System (INIS)

Basdekas, D.L.; Silberberg, M.; Curtis, R.T.; Kelber, C.N.

1978-07-01

The objective of SIMMER qualification testing program is to assure that the mathematical models and input parameters are derived from experimental data, which, on the basis of criteria still to be established, are representative of the phenomena and processes governing the progression of a CDA in an LMFBR. At the present time, the work to meet this objective can be classified into three general task areas as they relate to the use of SIMMER in CDA analysis: (1) The whole-core energetic disassembly accident, or the ''vessel problem'': The objective here is to predict the partition of the total energy release, by a postulated severe power excursion, between the primary containment and the energy absorbed through nondestructive dissipative processes. (2) Single subassembly accident: The objective here is to determine the pertinent phenomena and to develop the capability to assess the significance and likelihood that such accidents might propagate to involvement of larger fraction of the core. (3) The whole-core transition phase accident: The objective here is to advance the understanding of the phenomena and processes involved, so that reliable predictions can be made of the possible consequences of a CDA and the potential for further nuclear excursions through recriticality

High-density multicore fiber with heterogeneous core arrangement

DEFF Research Database (Denmark)

Amma, Y.; Sasaki, Y.; Takenaga, K.

2015-01-01

A 30-core fiber with heterogeneous cores that achieved large spatial multiplicity and low crosstalk of less than −40 dB at 100 km was demonstrated. The correlation lengths were estimated to be more than 1 m.......A 30-core fiber with heterogeneous cores that achieved large spatial multiplicity and low crosstalk of less than −40 dB at 100 km was demonstrated. The correlation lengths were estimated to be more than 1 m....

Analysis of a postulated accident scenario involving loss of forced flow in a LMFBR

International Nuclear Information System (INIS)

Moreira, M.L.

1985-01-01

A model to analyse a postulated accident scenario involving loss of forced flow in the reactor vessel of a LMFBR is used. Five phases of the accident are analysed: Natural Circulation, Subcooled Boiling, Nucleate Boiling, Core Dryout and Cladding melt. The heat conduction in the fuel cladding, coolant and lower and upper plenum are calculated by a lump-parameter model. Physical data of a prototype LMFBR reactor were used for the calculation. (author)

Heterogeneous gas core reactor

International Nuclear Information System (INIS)

Diaz, N.J.; Dugan, E.T.

1983-01-01

A heterogeneous gas core nuclear reactor is disclosed comprising a core barrel provided interiorly with an array of moderator-containing tubes and being otherwise filled with a fissile and/or fertile gaseous fuel medium. The fuel medium may be flowed through the chamber and through an external circuit in which heat is extracted. The moderator may be a fluid which is flowed through the tubes and through an external circuit in which heat is extracted. The moderator may be a solid which may be cooled by a fluid flowing within the tubes and through an external heat extraction circuit. The core barrel is surrounded by moderator/coolant material. Fissionable blanket material may be disposed inwardly or outwardly of the core barrel

A LMFBR for thorium utilization and for the U233/Th fuel rods specification

International Nuclear Information System (INIS)

Ishiguro, Y.; Dias, A.F.

1982-01-01

The use of U 233 /Th as fuel in the middle part of LMFBR core and the Pu/U in the external part of the core, are proposed. The basic neutronic and safety characteristics and the specifications of fuel rods to be used in the internal core, are presented. (E.G.) [pt

A study of sodium-cooled fast breeder reactor with thorium blanket for supply of U-233 to high temperature gas cooled reactor

International Nuclear Information System (INIS)

Yoshida, H.; Nishimura, H.; Osugi, T.

1978-08-01

Symbiotic energy system between fast breeder reactor and thermal reactor would have a potential merit for nuclear proliferation problem. And when using HTGR as the thermal reactor in the system, the energy system appears to be promising as an energy system self-sufficient in fuels, which can generate both electricity and high temperature process heat. In the system the fast breeder reactor has to supply sufficient amount of fissile plutonium to keep the reactor going, and also produce U-233 necessary to the associated U-233 fuelled process heat production HTGR. Three types of LMFBR concepts with thorium blanket, conventional homogeneous core LMFBR, and axial and radial parfait heterogeneous core LMFBRs, have been investigated to find out suitable configurations of LMFBR for supply of U-233 to the HTGR with relatively high conversion ratio of 0.85, in the symbiotic energy system between LMFBR and HTGR. The investigation on LMFBR has been made on fuel sufficiency of the system, inherent safety such as sodium-void and Doppler coefficients, and fuel cycle cost. The followings were revealed; (1) Conventional homogeneous core LMFBR with thorium radial blanket well satisfies the condition of fuel sufficiency, if adequate radial blanket thickness is chosen. However, the sodium-void coefficient and fuel cycle cost are inferior to the other concepts. (2) Axial parfait heterogeneous core LMFBR can be regarded as one of the best LMFBR concepts installed in the symbiotic energy system, from the viewpoints of fuel sufficiency, inherent safety and fuel cycle cost. However, further investigations should be needed on reliability and operationability of the concept. (3) Radial parfait heterogeneous core LMFBR seems inadequate as the LMFBR in the system, because the configurations based on this concept does not satisfy plutonium and U-233 breedings, simultaneously. This LMFBR concept, however, has excellent breeding performance in the internal radial blanket. So further

LMFBR operational and experimental in-core local-fault experience, primarily with oxide fuel elements

International Nuclear Information System (INIS)

Warinner, D.K.

Case-by-case reviews of selective world experience with severe local faults, particularly fuel failure and fuel degradation, are reviewed for two sodium-cooled thermal reactors, several LMFBRs, and LMFBR-fuels experiments. The review summarizes fuel-failure frequency and illustrates the results of the most damaging LMFBR local-fault experiences of the last 20 years beginning with BR-5 and including DFR, BOR-60, BR2's MFBS-and Mol-loops experiments, Fermi, KNK, Rapsodie, EBR-II, and TREAT-D2. Local-fault accommodation is demonstrated and a need to more thoroughly investigate delayed-neutron and gaseous-fission-product signals is highlighted in view of uranate formation, observed blockages, and slow fuel-element failure-propagation

TRANSENERGY S: computer codes for coolant temperature prediction in LMFBR cores during transient events

International Nuclear Information System (INIS)

Glazer, S.; Todreas, N.; Rohsenow, W.; Sonin, A.

1981-02-01

This document is intended as a user/programmer manual for the TRANSENERGY-S computer code. The code represents an extension of the steady state ENERGY model, originally developed by E. Khan, to predict coolant and fuel pin temperatures in a single LMFBR core assembly during transient events. Effects which may be modelled in the analysis include temporal variation in gamma heating in the coolant and duct wall, rod power production, coolant inlet temperature, coolant flow rate, and thermal boundary conditions around the single assembly. Numerical formulations of energy equations in the fuel and coolant are presented, and the solution schemes and stability criteria are discussed. A detailed description of the input deck preparation is presented, as well as code logic flowcharts, and a complete program listing. TRANSENERGY-S code predictions are compared with those of two different versions of COBRA, and partial results of a 61 pin bundle test case are presented

Comparative analysis of a hypothetical 0.1 $/SEC transient overpower accident in an irradiated LMFBR core using different computer models

International Nuclear Information System (INIS)

Cacciabue, P.C.; Fremont, R. de; Renard, A.

1982-01-01

The Report gives the results of comparative calculations performed by the Whole Core Accident Codes Group which is a subgroup of the Safety Working Group of the Fast Reactor Coordinating Committee for a hypothetical transient overpower accident in an irradiated LMFBR core. Different computer codes from members of the European Community and the United States were used. The calculations are based on a Benchmark problem, using commonly agreed input data for the most important phenomena, such as the fuel pin failure threshold, FCl parameters, etc. Beside this, results with alternative assumptions for theoretical modelling are presented with the scope to show in a parametric way the influence of more advanced modelling capabilities and/or better (so-called best estimate) input data for the most important phenomena on the accident sequences

LMFBR type reactor

International Nuclear Information System (INIS)

Masumi, Ryoji; Kawashima, Katsuyuki; Kurihara, Kunitoshi.

1988-01-01

Purpose: To flatten the power distribution while maintaining the flattening in the axial power distribution in LMFBR type reactors. Constitution: Main system control rods are divided into control rods used for the operation and starting rods used for the starting of the reactor, and the starting rods are disposed in the radial periphery of the reactor core, while the control rods are disposed to the inside of the starting rods. With such a constitution, adjusting rods can be disposed in the region where the radial power peaking is generated to facilitate the flattening of the power distribution even in such a design that the ratio of the number of control rods to that of fuel assemblies is relatively large. That is, in this reactor, the radial power peaking is reduced by about 10% as compared with the conventional reactor core. As a result, the maximum linear power density during operation is reduced by about 10% to increase the thermal margin of the reactor core. If the maximum linear power density is set identical, the number of the fuel assemblies can be decreased by about 10%, to thereby reduce the fuel production cost. (K.M.)

LMFBR design and its evolution. (2) Core design of LMFBR

International Nuclear Information System (INIS)

Uto, Nariaki; Mizuno, Tomoyasu

2003-01-01

Sodium-cooled core design studies are performed. MOX fuel core with axial blanket partial elimination subassembly due to safety consideration is studied. This type of core with high internal conversion ratio possesses capability of achieving 26 months of operation cycle length and 100 GWd/t of burnup averaged over core and blanket, which are superior characteristics in view of reducing cost of power generation. Metal fuel core is also studied, and its higher breeding capability reveals a potential of better core performance such as longer operation cycle length for the same level of electricity generation, though core outlet temperature is limited to lower level due to steel cladding-metal fuel compatibility concerns. Another metal fuel core concept using single Pu enrichment and two radial regions with individual fuel pin diameters achieves 550degC of core outlet temperature identical to that of MOX fuel core, keeping operation cycle length comparable with that of MOX fuel core. This series of study results show that sodium-cooled MOX and metal fuel cores have a high flexibility in satisfying various needs including fuel cycle cost and breeding capability, depending on the stage of introducing commercialized fast reactor cycle system. (author)

LMFBR plant parameters

International Nuclear Information System (INIS)

1979-03-01

This document contains up-to-date data on existing or firmly decided prototype or demonstration LMFBR reactors (Table I), on planned commercial size LMFBR according to the present status of design (Table II) and on experimental fast reactors such as BOR-60, DFR, EBR-II, FERMI, FFTF, JOYO, KNK-II, PEC, RAPSODIE-FORTISSIMO (Table III). Only corrected and revised parameters submitted by the countries participating in the IWGFR are included in this document

Contribution of Clinch River Breeder Reactor plant design and development to the LMFBR fuel cycle

International Nuclear Information System (INIS)

Riley, D.R.; Dickson, P.W.

1981-01-01

This paper describes how the CRBRP development and CRBRP focus of the LMFBR base technology program have led to advances in the state of the art in physics, thermal-hydraulics, structural analysis, core restraint, seismic analysis, and analysis of hypothetical core-disruptive accident energetics, all of which have been incorporated through disciplined engineering into the final CRBRP design. The total development in the US of fuels and materials, the analytical advances made on CRBRP design, and the incorporation of the latest experimental results into that design have put the US technology in general and the CRBRP design in particular at the forefront of technology. This has placed the US in a position to develop the most favorable LMFBR fuel cycle

Crosstalk-Managed Heterogeneous Single-Mode 32-Core Fibre

DEFF Research Database (Denmark)

Sasaki, Y.; Fukumoto, Ryohei; Takenaga, Katsuhiro

2016-01-01

A heterogeneous single-mode 32-core fibre with a cladding diameter of 243 micrometer is designed and fabricated. The highest core count in single-mode multi-core fibres and low worst-case crosstalk of less than -24 dB/1000 km in C-band are achieved simultaneously....

Refractory metal carbide coatings for LMFBR applications: a systems approach

International Nuclear Information System (INIS)

Gotschall, H.L.; Ople, F.S.; Riccardella, P.C.

1975-01-01

The selection, testing and improvement of high density, tightly bonded plasma and detonation gun coatings designed to meet LMFBR core component criteria are described. The process descriptions include a review of the important developments in substrate surface preparation which were required to ensure strong bonding and to minimize interface contamination. Coating finishing techniques which were developed to optimize friction behavior are also described

Tank type LMFBR type reactors

International Nuclear Information System (INIS)

Shimizu, Hiroshi

1985-01-01

Purpose: To detect the abnormality in the suspended body or reactor core supporting structures thereby improve the safety and reliability of tank type LMFBR reactors. Constitution: Upon inspection during reactor operation period, the top end of the gripper sensing rod of a fuel exchanger is abutted against a supporting bed and the position of the reactor core supporting structures from the roof slab is measured by a stroke measuring device. Then, the sensing rod is pulled upwardly to abut against the arm portion and the position is measured by the stroke measuring device. The measuring procedures are carried out for all of the sensing rods and the measured values are compared with a previously determined value at the initial stage of the reactor operation. As a result, it is possible to detect excess distortions and abnormal deformation in the suspended body or reactor core supporting structures. Furthermore, integrity of the suspended body against thermal stresses can be secured by always measuring the coolant liquid level by the level measuring sensor. (Kamimura, M.)

LMFBR Ultra Long Life Cores

International Nuclear Information System (INIS)

Schmidt, J.E.; Doncals, R.A.; Porter, C.A.; Gundy, L.M.

1986-01-01

The Ultra Long Life Core is an attractive and innovative design approach with several extremely beneficial attributes. Long Life cores are applicable to the full range of LMR plant sizes resulting in lifetimes up to 30 years. Core life is somewhat limited for smaller plant sizes, however significant benefits of this approach still exist for all plant sizes. The union of long life cores and the complementary inherent safety technology offer a means of utilizing the well-proven oxide fuel in a system with unsurpassed safety capability. A further benefit is that the uranium fuel cycle can be used in long life cores, especially for initial LMR plant deployment, thereby eliminating the need for reprocessing prior to starting LMR plant construction in the U.S. Finally the long life core significantly reduces power costs. With inherent safety capability designed into an LMR and with the ULLC fuel cycle, power costs competitive with light water plants are achievable while offering improved operational flexibility derived through extending refueling intervals

LMFBR safety criteria: cost-benefit considerations under the constraint of an a priori risk criterion

International Nuclear Information System (INIS)

Hartung, J.

1979-01-01

The role of cost-benefit considerations and a priori risk criteria as determinants of Core Disruptive Accident (CDA)-related safety criteria for large LMFBR's is explored with the aid of quantitative risk and probabilistic analysis methods. A methodology is described which allows a large number of design and siting alternatives to be traded off against each other with the goal of minimizing energy generation costs subject to the constraint of both an a priori risk criterion and a cost-benefit criterion. Application of this methodology to a specific LMFBR design project is described and the results are discussed. 5 refs

Study on the seismic response of reactor vessel of pool type LMFBR including fluid-structure interaction

International Nuclear Information System (INIS)

Tanimoto, K.; Ito, T.; Fujita, K.; Kurihara, C.; Sawada, Y.; Sakurai, A.

1988-01-01

The paper presents the seismic response of reactor vessel of pool type LMFBR with fluid-structure interaction. The reactor vessel has bottom support arrangement, the same core support system as Super-Phenix in France. Due to the bottom support arrangement, the level of core support is lower than that of the side support arrangement. So, in this reactor vessel, the displacement of the core top tends to increase because of the core's rocking. In this study, we investigated the vibration and seismic response characteristics of the reactor vessel. Therefore, the seismic experiments were carried out using one-eighth scale model and the seismic response including FSI and sloshing were investigated. From this study, the effect of liquid on the vibration characteristics and the seismic response characteristics of reactor vessel were clarified and sloshing characteristics were also clarified. It was confirmed that FEM analysis with FSI can reproduce the seismic behavior of the reactor vessel and is applicable to seismic design of the pool type LMFBR with bottom support arrangement. (author). 5 refs, 14 figs, 2 tabs

LMFBR core design analysis

International Nuclear Information System (INIS)

Cho, M.; Yang, J.C.; Yoh, K.C.; Suk, S.D.; Soh, D.S.; Kim, Y.M.

1980-01-01

The design parameters of a commercial-scale fast breeder reactor which is currently under construction by regeneration of these data is preliminary analyzed. The analysis of nuclear and thermal characteristics as well as safety features of this reactor is emphasized. And the evaluation of the initial core mentioned in the system description is carried out in the areas of its kinetics and control system, and, at the same time, the flow distribution of sodium and temperature distribution of the initial FBR core system are calculated. (KAERI INIS Section)

Beacon: A three-dimensional structural analysis code for bowing history of fast breeder reactor cores

International Nuclear Information System (INIS)

Miki, K.

1979-01-01

The core elements of an LMFBR are bowed due to radial gradients of both temperature and neutron flux in the core. Since all hexagonal elements are multiply supported by adjacent elements or the restraint system, restraint forces and bending stresses are induced. In turn, these forces and stresses are relaxed by irradiation enhanced creep of the material. The analysis of the core bowing behavior requires a three-dimensional consideration of the mechanical interactions among the core elements, because the core consists of different kinds of elements and of fuel assemblies with various burnup histories. A new computational code BEACON has been developed for analyzing the bowing behavior of an LMFBR's core in three dimensions. To evaluate mechanical interactions among core elements, the code uses the analytical method of the earlier SHADOW code. BEACON analyzes the mechanical interactions in three directions, which form angles of 60 0 with one another. BEACON is applied to the 60 0 sector of a typical LMFBR's core for analyzing the bowing history during one equilibrium cycle. 120 core elements are treated, assuming the boundary condition of rotational symmetry. The application confirms that the code can be an effective tool for parametric studies as well as for detailed structural analysis of LMFBR's core. (orig.)

Network Coding on Heterogeneous Multi-Core Processors for Wireless Sensor Networks

Science.gov (United States)

Kim, Deokho; Park, Karam; Ro, Won W.

2011-01-01

While network coding is well known for its efficiency and usefulness in wireless sensor networks, the excessive costs associated with decoding computation and complexity still hinder its adoption into practical use. On the other hand, high-performance microprocessors with heterogeneous multi-cores would be used as processing nodes of the wireless sensor networks in the near future. To this end, this paper introduces an efficient network coding algorithm developed for the heterogenous multi-core processors. The proposed idea is fully tested on one of the currently available heterogeneous multi-core processors referred to as the Cell Broadband Engine. PMID:22164053

Theoretical study and experimental investigation of mixed and natural circulation in LMFBR core subassemblies

International Nuclear Information System (INIS)

Leteinturier, D.; Blanc, D.; Menant, B.; Basque, G.

1980-02-01

A presentation is made of theoretical and experimental studies carried out in France on mixed and natural convection in LMFBR wire wrapped bundles. Two codes are described, one for mixed convection THERNAT and the other for natural convection BACCHUS. THe related experimental program FETUNA, with electrically heated bundles in sodium loops, is also presented

Issues in the selection of the LMFBR steam cycle

International Nuclear Information System (INIS)

Buschman, H.W.; McConnell, R.J.

1983-01-01

Unlike the light-water reactor, the liquid-metal fast breeder reactor (LMFBR) allows the designer considerable latitude in the selection of the steam cycle. This latitude in selection has been exercised by both foreign and domestic designers, and thus, despite the fact that over 25 LMFBR's have been built or are under construction, a consensus steam cycle has not yet evolved. This paper discusses the LMFBR steam cycles of interest to the LMFBR designer, reviews which of these cycles have been employed to date, discusses steam-cycle selection factors, discusses why a consensus has not evolved, and finally, concludes that the LMFBR steam-cycle selection is primarily one of technical philosophy with several options available

Dynamic response of single hexagonal LMFBR core subassembly wrappers

Energy Technology Data Exchange (ETDEWEB)

Ash, J. E.; Marciniak, T. J.; (Argonne National Lab., IL (United States))

1977-07-01

To analyze the dynamic structural response of the LMFBR core subassembly hexagonal wrappers to postulated local energy releases and the sensitivity of the response to variations in both the pressure loading and the material properties of the stainless steel, a finite-element computer code STRAW has been developed. A series of experiments was performed to study the effects of variations in material properties. The amount of coldworking to which the Type 316 stainless steel is subjected has a strong influence upon the ductility and the elastic yield point. The usual fabrication process produced a nominally 20% coldworking with a yield point of about 680 MPa. By designing a special set of dies for the drawing process, a very low ductility hexcan was produced for which the yield point was raised to 820 MPa. Conversely, the yield point was lowered to 170 MPa by a solution annealing process producing a highly ductile test hexcan. A metallurgical study was conducted to find a representative brittle simulant material for the irradiated end-of-life steel properties. An aging treatment for Type 446 stainless steel was developed which reproduced the expected tensile-flow behavior of the in-pile subassembly. Further study is underway to investigate the fracture properties of the simulant material. The pressure pulses were generated by the controlled expansion of high-pressure detonation poducts from low-density explosives detonated inside a vented steel cannister. The orifice configuration of the cannister and the charge mixture ratio were designed to produce two specified pulse shapes. A charge containing 37,7 g PETN mixed with 35 wt % inert, hollow-glass microballoons developed a pressure pulse peak of 9.5 MPa at 1.0 ms. Increasing the PETN to 41 g resulted in a 14.6 MPa peak pressure, and increasing the explosive concentration to 90 wt % in the mixture increased the burning rate and the pulse risetime, so that the peak occurred at 0.6 ms.

Component design for LMFBR's

International Nuclear Information System (INIS)

Fillnow, R.H.; France, L.L.; Zerinvary, M.C.; Fox, R.O.

1975-01-01

Just as FFTF has prototype components to confirm their design, FFTF is serving as a prototype for the design of the commercial LMFBR's. Design and manufacture of critical components for the FFTF system have been accomplished primarily using vendors with little or no previous experience in supplying components for high temperature sodium systems. The exposure of these suppliers, and through them a multitude of subcontractors, to the requirements of this program has been a necessary and significant step in preparing American industry for the task of supplying the large mechanical components required for commercial LMFBR's

Water tests for determining post voiding behavior in the LMFBR

International Nuclear Information System (INIS)

Hinkle, W.D.

1976-06-01

The most serious of the postulated accidents considered in the design of the Liquid Metal Cooled Fast Breeder Reactor (LMFBR) is the Loss of Pipe Integrity (LOPI) accident. Analysis models used to calculate the consequences of this accident assume that once boiling is initiated film dryout occurs in the hot assembly as a result of rapid vapor bubble growth and consequent flow stoppage or reversal. However, this assumption has not been put to any real test. Once boiling is initiated in the hot assembly during an LMFBR LOPI accident, a substantial gravity pressure difference would exist between this assembly and other colder assemblies in the core. This condition would give rise to natural circulation flow boiling accompanied by pressure and flow oscillations. It is possible that such oscillations could prevent or delay dryout and provide substantial post-voiding heat removal. The tests described were conceived with the objective of obtaining basic information and data relating to this possibility

Confirmatory simulation of safety and operational transients in LMFBR systems

International Nuclear Information System (INIS)

Guppy, J.G.; Agrawal, A.K.

1978-01-01

Operational and safety transients (anticipated, unlikely, or extremely unlikely) that may originate anywhere in a liquid-metal fast breeder reactor (LMFBR) system must be adequately simulated to assist in safety evaluation and plant design efforts. An advanced thermohydraulic transient code, the Super System Code (SSC), is described that may be used for confirmatory safety evaluations of plant-wide events, such as assurance of adequate decay heat removal capability under natural circulation conditions. Results obtained with SSC illustrating the degree of modeling detail present in the code as well as the computing efficiency are presented. A version of the SSC code, SSC-L, applicable to any loop-type LMFBR design, has been developed at Brookhaven. The scope of SSC-L is to enable the simulation of all plant-wide transients covered by Plant Protection System (PPS) action, including sodium pipe rupture and coastdown to natural circulation conditions. The computations are stopped when loss of core integrity (i.e., clad melting temperature exceeded) is indicated

The state of art of the methods for thermohydraulics design of LMFBR fuel elements

International Nuclear Information System (INIS)

Fernandez y Fernandez, E.; Carajilescov, P.

1981-09-01

The present (experimental and analytical) state of art of the methods for thermohydraulics design of LMFBR fuel elements is analyzed. A development program is suggested, in order to obtain a computer code for modelling the distribution of coolant enthalpy in reactor core. This computer code is in development. (Author) [pt

Comparative analysis of a hypothetical loss-of-flow accident in an irradiated LMFBR core using different computer models for a common benchmark problem

International Nuclear Information System (INIS)

Wider, H.U.; Devos, J.; Nguyen, H.; Goethem, G. Van.; Miles, K.J.; Tentner, A.M.; Pizzica, P.

1989-01-01

This report summarizes the results of an international exercise to compare whole-core accident calculations of the initiation phase of an unprotected LOF accident in a large irradiated LMFBR. The results for the accident phase before pin failure are in rather good agreement except for the fuel pin mechanics predictions. There are also some differences in the sodium boiling calculations but the voiding rates which are of key importance are very similar. The post - failure fuel motion and sodium voiding predictions show significant differences. However, the majority of these calculations agree that temporary fuel accumulations occur which increase the power beyond that caused by sodium voiding alone

Validation study of the COBRA-WC computer program for LMFBR core thermal-hydraulic analysis

International Nuclear Information System (INIS)

Khan, E.U.; Bates, J.M.

1982-01-01

The COBRA-WC (Whole Core) computer program has been developed as a benchmark code to predict flow and temperature fields in LMFBR rod bundles. Consequently, an extensive validation study has been conducted to reinforce its credibility. A set of generalized parameters predicts data well for a wide range of geometries and operating conditions which include conventional (current generation LMFBRs) fuel and blanket assembly geometry in the forced, mixed, and natural convection regimes. The data base used for validating COBRA-WC was obtained from out-of-pile and in-pile tests. Most of the data was obtained in fully heated bundles with bundle power skew across flats up to 3:1 (max:min), Reynolds number between 500 and 80,000, and coolant mixed-mean temperature rise (δ anti T) in the range, 78 0 F less than or equal to δ anti T less than or equal to 340 0 F. Within the bundle, 95% of the predicted coolant temperature data points fall within +-25 0 F for 150 0 F less than or equal to δ anti T less than or equal to 340 0 F and within +-17 0 F for 78 0 F less than or equal to δ anti T less than or equal to 150 0 F

Ferritic steels for French LMFBR steam generators

International Nuclear Information System (INIS)

Aubert, M.; Mathieu, B.; Petrequin, P.

1983-06-01

Austenitic stainless steels have been widely used in many components of the French LMFBR. Up to now, ferritic steels have not been considered for these components, mainly due to their relatively low creep properties. Some ferritic steels are usable when the maximum temperatures in service do not exceed about 530 0 C. It is the case of the steam generators of the Phenix plant, where the exchange tubes of the evaporator are made of 2,25% Cr-1% Mo steel, stabilized or not by addition of niobium. These ferritic alloys have worked successfully since the first steam production in October 1973. For the SuperPhenix power plant, an ''all austenitic stainless alloy'' apparatus has been chosen. However, for the future, ferritic alloys offer potential for use as alternative materials in the evaporators: low alloys steels type 2,25% Cr-1% Mo (exchange tubes, tube-sheets, shells), or at higher chromium content type 9% Cr-2% Mo NbV (exchange tubes) or 12M Cr-1% Mo-V (tube-sheets). Most of these steels have already an industrial background, and are widely used in similar applications. The various potential applications of these steels are reviewed with regards to the French LMFBR steam generators, indicating that some points need an effort of clarification, for instance the properties of the heterogeneous ferritic/austenitic weldments

Applicability of the Reactor Safety Study (WASH-1400) to LMFBR risk assessments

International Nuclear Information System (INIS)

El-Sheikh, K.A.; Feller, K.G.; Fleischer, L.; Greebler, P.; McDonald, A.; Sultan, P.; Temme, M.I.; Fullwood, R.R.

1976-01-01

The feasibility of applying the WASH-1400 methods and data to LMFBR risk assessment is evaluated using the following approach for a selected LMFBR: (1) Structuring the LMFBR risk assessment problem in a modular form similar to WASH-1400; (2) Comparing the predictive tools applicable to each module; (3) Comparing the dependencies among the various modules. It is concluded that the WASH-1400 applicability is limited due to LWR-LMFBR differences in operating environments and accident phenomena. WASH-1400 and LMFBR specific methods applicable to LMFBR risk assessments are indicated

Axial heterogeneous core concept applied for super phoenix reactor

International Nuclear Information System (INIS)

Batista, J.L.; Renke, C.A.C.; Waintraub, M.; Santos Bastos, W. dos; Brito Aghina, L.O. de.

1991-11-01

Always maintaining the current design rules, this paper presents a parametric study on the type of axial heterogeneous core concept (CHA), utilizing a core of fast reactor Super Phenix type, reaching a maximum thermal burnup rate of 150000 M W d/t and being managed in single batch. (author)

Damping in LMFBR pipe systems

International Nuclear Information System (INIS)

Anderson, M.J.; Barta, D.A.; Lindquist, M.R.; Renkey, E.J.; Ryan, J.A.

1983-06-01

LMFBR pipe systems typically utilize a thicker insulation package than that used on water plant pipe systems. They are supported with special insulated pipe clamps. Mechanical snubbers are employed to resist seismic loads. Recent laboratory testing has indicated that these features provide significantly more damping than presently allowed by Regulatory Guide 1.61 for water plant pipe systems. This paper presents results of additional in-situ vibration tests conducted on FFTF pipe systems. Pipe damping values obtained at various excitation levels are presented. Effects of filtering data to provide damping values at discrete frequencies and the alternate use of a single equivalent modal damping value are discussed. These tests further confirm that damping in typical LMFBR pipe systems is larger than presently used in pipe design. Although some increase in damping occurred with increased excitation amplitude, the effect was not significant. Recommendations are made to use an increased damping value for both the OBE and DBE seismic events in design of LMFBR pipe systems

Low cycle fatigue of irradiated LMFBR materials

International Nuclear Information System (INIS)

Blackburn, L.D.

1976-01-01

A review of low cycle fatigue data on irradiated LMFBR materials was conducted and extensive graphical representations of available data are presented. Representative postirradiation tensile properties of annealed 304 and 316 SS are selected and employed in several predictive methods to estimate irradiated material fatigue curves. Experimental fatigue data confirm the use of predictive methods for establishing conservative design curves over the range of service conditions relevant to such CRBRP components as core former, fixed radial shielding, core barrel, lower inlet module and upper internals structures. New experimental data on fatigue curves and creep-fatigue interaction in irradiated 20 percent cold worked (CW) 316 SS and Alloy 718 would support the design of removable radial shielding and upper internals in CRBRP. New experimental information on notched fatigue behavior and cyclic stress-strain curves of all these materials in the irradiated condition could provide significant design data

A miniature inductive temperature sensor to monitor temperature noise in the coolant of an LMFBR

International Nuclear Information System (INIS)

Dean, S.A.; Sandham, C.W.

1980-01-01

A description is given of the design and performance of miniature inductive sensors developed to monitor fast temperature fluctuations in the sodium coolant above the core of a LMFBR. These instruments, designed to be installed within existing thermocouple containment thimbles, also provide a steady-state temperature indication for reactor control purposes. (author)

CQPSO scheduling algorithm for heterogeneous multi-core DAG task model

Science.gov (United States)

Zhai, Wenzheng; Hu, Yue-Li; Ran, Feng

2017-07-01

Efficient task scheduling is critical to achieve high performance in a heterogeneous multi-core computing environment. The paper focuses on the heterogeneous multi-core directed acyclic graph (DAG) task model and proposes a novel task scheduling method based on an improved chaotic quantum-behaved particle swarm optimization (CQPSO) algorithm. A task priority scheduling list was built. A processor with minimum cumulative earliest finish time (EFT) was acted as the object of the first task assignment. The task precedence relationships were satisfied and the total execution time of all tasks was minimized. The experimental results show that the proposed algorithm has the advantage of optimization abilities, simple and feasible, fast convergence, and can be applied to the task scheduling optimization for other heterogeneous and distributed environment.

Strategies in development of advanced fuels for LMFBR

International Nuclear Information System (INIS)

Handa, Muneo

1976-12-01

Overseas strategies in development of advanced fuels for LMFBR are reviewed. Recent irradiation experiment and out-of-pile test data of the fuels are given in detail. The present status of development of oxide fueled LMFBR is also treated. (auth.)

Performance analysis of LMFBR control rods

International Nuclear Information System (INIS)

Pitner, A.L.; Birney, K.R.

1975-01-01

Control rods in the FFTF and LMFBR's will consist of pin bundles of stainless steel-clad boron carbide pellets. In the FFTF reference design, sixty-one pins of 0.474-inch diameter each containing a 36-inch stack of 0.362-inch diameter boron carbide pellets comprise a control rod. Reactivity control is provided by the 10 B (n,α) 7 Li reaction in the boron carbide. This reaction is accompanied by an energy release of 2.8 MeV, and heating from this reaction typically approaches 100 watts/cm 3 for natural boron carbide pellets in an LMFBR flux. Performance analysis of LMFBR control rods must include an assessment of the thermal performance of control pins. In addition, irradiation performance with regard to helium release, pellet swelling, and reactivity worth depletion as a function of service time must be evaluated

Whole-core thermal-hydraulic transient code development and verification for LMFBR analysis

International Nuclear Information System (INIS)

Spencer, D.R.

1979-04-01

Predicted performance during both steady state and transient reactor operation determines the steady state operating limits on LMFBRs. Unnecessary conservatism in performance predictions will not contribute to safety, but will restrict the reactor to more conservative, less economical steady state operation. The most general method for reducing analytical conservatism in LMFBR's without compromising safety is to develop, validate and apply more sophisticated computer models to the limiting performance analyses. The purpose of the on-going Natural Circulation Verification Program (NCVP) is to develop and validate computer codes to analyze natural circulation transients in LMFBRs, and thus, replace unnecessary analytical conservatism with demonstrated calculational capability

Core mechanics and configuration behavior of advanced LMFBR core restraint concepts

International Nuclear Information System (INIS)

Fox, J.N.; Wei, B.C.

1978-02-01

Core restraint systems in LMFBRs maintain control of core mechanics and configuration behavior. Core restraint design is complex due to the close spacing between adjacent components, flux and temperature gradients, and irradiation-induced material property effects. Since the core assemblies interact with each other and transmit loads directly to the core restraint structural members, the core assemblies themselves are an integral part of the core restraint system. This paper presents an assessment of several advanced core restraint system and core assembly concepts relative to the expected performance of currently accepted designs. A recommended order for the development of the advanced concepts is also presented

Comparison of different LMFBR primary containment codes applied to a Benchmark problem

International Nuclear Information System (INIS)

Benuzzi, A.

1986-01-01

The Cont Benchmark calculation exercise is a project sponsored by the Containment Loading and Response Group, a subgroup of the Safety Working Group of the Fast Reactor Coordinating Committee - CEC. A full-size typical Pool type LMFBR undergoing a postulated Core Disruptive Accident (CDA) has been defined by Belgonucleaire-Brussels under a study contract financed by the CEC and has been submitted to seven containment code calculations. The results of these calculations are presented and discussed in this paper

Monte-Carlo validation of secondary sodium activation in a pool-type LMFBR

International Nuclear Information System (INIS)

Plamiotti, G.; Rado, V.; Salvatores, M.

1980-09-01

The secondary sodium activation in a pool-type LMFBR is the main parameter to be accurately evaluated in the shield design. In the present work a complete two dimensional description of the system, including core, shielding and sodium up to Heat Exchangers, is coupled to local Heat Exchanger Monte-Carlo calculations. This refined calculation is used to deduce a simplified method to take into account the coupling of radial propagation in the Heat Exchanger and its finite cylindrical structure

LMFBR plant parameters

International Nuclear Information System (INIS)

1985-07-01

This document has been prepared on the basis of information compiled by the members of the IAEA International Working Group on Fast Reactors (IWGFR). It contains parameters of 25 experimental, prototype and commercial size liquid metal fast breeder reactors (LMFBR). Most of the reactors are currently in operation, under construction or in an advanced planning stage. Parameters of the Clinch River Breeder Reactor (USA) are presented because its design was nearly finished and most of the components were fabricated at the time when the project was terminated. Three reactors (RAPSODIE (France), DFR (UK) and EFFBR (USA)) have been shut down. However, they are included in the report because of their important role in the development of LMFBR technology from first LMFBRs to the prototype size fast reactors. The first LMFBRs (CLEMENTINE (USA), EBR-1 (USA), BR-2 (USSR), BR-5 (USSR)) and very special reactors (LAMPRE (USA), SEFOR (USA)) were not recommended by the members of the IWGFR to be included in the report

Efficient Support for Matrix Computations on Heterogeneous Multi-core and Multi-GPU Architectures

Energy Technology Data Exchange (ETDEWEB)

Dong, Fengguang [Univ. of Tennessee, Knoxville, TN (United States); Tomov, Stanimire [Univ. of Tennessee, Knoxville, TN (United States); Dongarra, Jack [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2011-06-01

We present a new methodology for utilizing all CPU cores and all GPUs on a heterogeneous multicore and multi-GPU system to support matrix computations e ciently. Our approach is able to achieve the objectives of a high degree of parallelism, minimized synchronization, minimized communication, and load balancing. Our main idea is to treat the heterogeneous system as a distributed-memory machine, and to use a heterogeneous 1-D block cyclic distribution to allocate data to the host system and GPUs to minimize communication. We have designed heterogeneous algorithms with two di erent tile sizes (one for CPU cores and the other for GPUs) to cope with processor heterogeneity. We propose an auto-tuning method to determine the best tile sizes to attain both high performance and load balancing. We have also implemented a new runtime system and applied it to the Cholesky and QR factorizations. Our experiments on a compute node with two Intel Westmere hexa-core CPUs and three Nvidia Fermi GPUs demonstrate good weak scalability, strong scalability, load balance, and e ciency of our approach.

Comments on US LMFBR steam generator base technology

International Nuclear Information System (INIS)

Simmons, W.R.

1984-01-01

The development of steam generators for the LMFBR was recognized from the onset by the AEC, now DOE, as a difficult, challenging, and high-priority task. The highly reactive nature of sodium with water/steam requires that the sodium-water/steam boundaries of LMFBR steam generators possess a degree of leak-tightness reliability not normally attempted on a commercial scale. In addition, the LMFBR steam generator is subjected to high fluid temperatures and severe thermal transients. These requirements place great demand on materials, fabrication processes, and inspection methods; and even greater demands on the designer to provide steam generators that can meet these demanding requirements, be fabricated without unreasonable shop requirements, and tolerate off-normal effects

Preliminary review of critical shutdown heat removal items for common cause failure susceptibility on LMFBR's. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Allard, L.T.; Elerath, J.G.

1976-02-01

This document presents a common cause failure analysis for Critical LMFBR Shutdown Heat Removal Systems. The report is intended to outline a systematic approach to defining areas with significant potential for common causes of failure, and ultimately provide inputs to the reliability prediction model. A preliminary evaluation of postulatd single initiating causes resulting in multiple failures of LMFBR-SHRS items is presented in Appendix C. This document will be periodically updated to reflect new information and activity.

MIT LMFBR blanket research project. Final summary report

International Nuclear Information System (INIS)

Driscoll, M.J.

1983-08-01

This is a final summary report on an experimental and analytical program for the investigation of LMFBR blanket characteristics carried out at MIT in the period 1969 to 1983. During this span of time, work was carried out on a wide range of subtasks, ranging from neutronic and photonic measurements in mockups of blankets using the Blanket Test Facility at the MIT Research Reactor, to analytic/numerical investigations of blanket design and economics. The main function of this report is to serve as a resource document which will permit ready reference to the more detailed topical reports and theses issued over the years on the various aspects of project activities. In addition, one aspect of work completed during the final year of the project, on doubly-heterogeneous blanket configurations, is documented for the record

Analysis of a homogenous and heterogeneous stylized half core of a CANDU reactor

Energy Technology Data Exchange (ETDEWEB)

EL-Khawlani, Afrah [Physics Department, Sana' a (Yemen); Aziz, Moustafa [Nuclear and radiological regulatory authority, Cairo (Egypt); Ismail, Mahmud Yehia; Ellithi, Ali Yehia [Cairo Univ. (Egypt). Faculty of Science

2015-03-15

The MCNPX (Monte Carlo N-Particle Transport Code System) code has been used for modeling and simulation of a half core of CANDU (CANada Deuterium-Uranium) reactor, both homogenous and heterogeneous model for the reactor core are designed. The fuel is burnt in normal operation conditions of CANDU reactors. Natural uranium fuel is used in the model. The multiplication factor for homogeneous and heterogeneous reactor core is calculated and compared during fuel burnup. The concentration of both uranium and plutonium isotopes are analysed in the model. The flux and power distributions through channels are calculated.

NALAP: an LMFBR system transient code

International Nuclear Information System (INIS)

Martin, B.A.; Agrawal, A.K.; Albright, D.C.; Epel, L.G.; Maise, G.

1975-07-01

NALAP is a LMFBR system transient code. This code, adapted from the light water reactor transient code RELAP 3B, simulates thermal-hydraulic response of sodium cooled fast breeder reactors when subjected to postulated accidents such as a massive pipe break as well as a variety of other upset conditions that do not disrupt the system geometry. Various components of the plant are represented by control volumes. These control volumes are connected by junctions some of which may be leak or fill junctions. The fluid flow equations are modeled as compressible, single-stream flow with momentum flux in one dimension. The transient response is computed by integrating the thermal-hydraulic conservation equations from user-initialized operating conditions by an implicit numerical scheme. Point kinetics approximation is used to represent the time dependent heat generation in the reactor core

Safety research needs for carbide and nitride fueled LMFBR's. Final report

International Nuclear Information System (INIS)

Kastenberg, W.E.

1975-01-01

The results of a study initiated at UCLA during the academic year 1974--1975 to evaluate and review the potential safety related research needs for carbide and nitride fueled LMFBR's are presented. The tasks included the following: (1) Review Core and primary system designs for any significant differences from oxide fueled reactors, (2) Review carbide (and nitride) fuel element irradiation behavior, (3) Review reactor behavior in postulated accidents, (4) Examine analytical methods of accident analysis to identify major gaps in models and data, and (5) Examine post accident heat removal. (TSS)

Immersed acoustical transducers and their potential uses in LMFBR

International Nuclear Information System (INIS)

Argous, J.P.; Brunet, M.; Baron, J.; Lhuillier, C.; Segui, J.L.

1980-04-01

Six years satisfactory operation in PHENIX has proved the reliability and effectivness of under-sodium viewing (VISUS) and Acoustic Detection. This fact has been strong incentive to maintain, on the future LMFBR the visus as well as the Acoustic Detection functions. These two functions are performed on SUPER PHENIX, by two sets of distinct systems using the well-known solution. Taking into account of recent improvements in sodium immersible acoustic transducers technology, CEA decided to undertake the development of a multi-functions instrument. This paper gives an outline of this new concept, which should be able to reduce the cost and the complexity of core instrumentation

Use of reliability in the LMFBR industry

International Nuclear Information System (INIS)

Penland, J.R.; Smith, A.M.; Goeser, D.K.

1977-01-01

This mission of a Reliability Program for an LMFBR should be to enhance the design and operational characteristics relative to safety and to plant availability. Successful accomplishment of this mission requires proper integration of several reliability engineering tasks--analysis, testing, parts controls and program controls. Such integration requires, in turn, that the program be structured, planned and managed. This paper describes the technical integration necessary and the management activities required to achieve mission success for LMFBR's

Safety criteria for the future LMFBR's in France and main safety issues for the rapide 1500 project

International Nuclear Information System (INIS)

Justin, F.; Natta, M.; Orzoni, G.

1985-04-01

The main safety criteria for future LMFBR in France and the related issues for the RAPIDE 1500 project are presented and discussed. The evolutions with respect to SUPERPHENIX options and requirements are emphasized, in particular for the concerns of the prevention of core melt accidents, fuel damage limits and related required performances of the protection system, since one main option is not to consider whole core melt accidents in the containment design. One shall also point out the advantages of some mitigating features which were nevertheless added in the containment design, although without any explicit consideration for core melt accidents

Summary of treat experiments on oxide core-disruptive accidents

International Nuclear Information System (INIS)

Dickerman, C.E.; Rothman, A.B.; Klickman, A.E.; Spencer, B.W.; DeVolpi, A.

1979-02-01

A program of transient in-reactor experiments is being conducted by Argonne National Laboratory in the Transient Reactor Test (TREAT) facility to guide and support analyses of hypothetical core-disruptive accidents (HCDA) in liquid-metal fast breeder reactors (LMFBR). Test results provide data needed to establish the response of LMFBR cores to hypothetical accidents producing fuel failure, coolant boiling, and the movement of coolant, molten fuel, and molten cladding. These data include margins to fuel failure, the modes of failure and movements, and evidence for identification of the mechanisms which determine the failure and movements. A key element in the program is the fast-neutron hodoscope, which detects fuel movement as a function of time during experiments

Automated Integration of Dedicated Hardwired IP Cores in Heterogeneous MPSoCs Designed with ESPAM

Directory of Open Access Journals (Sweden)

Ed Deprettere

2008-06-01

Full Text Available This paper presents a methodology and techniques for automated integration of dedicated hardwired (HW IP cores into heterogeneous multiprocessor systems. We propose an IP core integration approach based on an HW module generation that consists of a wrapper around a predefined IP core. This approach has been implemented in a tool called ESPAM for automated multiprocessor system design, programming, and implementation. In order to keep high performance of the integrated IP cores, the structure of the IP core wrapper is devised in a way that adequately represents and efficiently implements the main characteristics of the formal model of computation, namely, Kahn process networks, we use as an underlying programming model in ESPAM. We present details about the structure of the HW module, the supported types of IP cores, and the minimum interfaces these IP cores have to provide in order to allow automated integration in heterogeneous multiprocessor systems generated by ESPAM. The ESPAM design flow, the multiprocessor platforms we consider, and the underlying programming (KPN model are introduced as well. Furthermore, we present the efficiency of our approach by applying our methodology and ESPAM tool to automatically generate, implement, and program heterogeneous multiprocessor systems that integrate dedicated IP cores and execute real-life applications.

FBR core mock-up RAPSODIE I - experimental analysis

International Nuclear Information System (INIS)

Brochard, D.; Buland, P.; Gantenbein, F.

1990-01-01

The main phenomena which influence the LMFBR core response to a seismic excitation are the fluid structure interaction and the impacts between subassemblies. To study the core behaviour, seismic tests have been performed on the core mock-up RAPSODIE with and without fluid and restraint ring and for different levels of excitation. This paper summarizes the results of these tests. (author)

Efficient Execution of Video Applications on Heterogeneous Multi- and Many-Core Processors

NARCIS (Netherlands)

Pereira de Azevedo Filho, A.

2011-01-01

In this dissertation we present methodologies and evaluations aiming at increasing the efficiency of video coding applications for heterogeneous many-core processors composed of SIMD-only, scratchpad memory based cores. Our contributions are spread in three different fronts: thread-level parallelism

Transient analysis of LMFBR reinforced/prestressed concrete containment

International Nuclear Information System (INIS)

Marchertas, A.H.; Belytschko, T.B.; Bazant, Z.P.

1979-01-01

The use of prestressed concrete reactor vessels (PCRVs) for LMFBR containment creates a need for analytical methods for treating the transient response of such structures, for LMFBR containments must be capable of sustaining the dynamic effects which arise in a hypothetical core disruptive accident (HCDA). These analyses require several unique features: a model of concrete which includes tensile cracking, a methodology for representing the prestressing tendons and for simulating the prestressing operation, and an efficient computational tool for treating the transient response. Furthermore, for the sake of convenience, all of these features should be available in a single computer code. For the purpose of treating the transient response, a finite element program with explicit time integration was chosen. The use of explicit time integration has the advantage that it can easily treat the complicated constitutive model which arises from the considerations of concrete cracking and it can handle the slip between reinforcing tendons and the concrete through the use of the well known sliding interface options. However, explicit time integration programs are usually not well suited to the simulation of static processes such as prestressing. Nevertheless, explicit time integration programs can handle static processes through the introduction of damping by what is known as a dynamic relaxation procedure. For this reason, the dynamic relaxation procedure was refined through the introduction of lumped mass, viscous damping. This provision made the prestressing operation of the concrete structures by means of the explicit formulation rather convenient. (orig.)

Energy-aware Thread and Data Management in Heterogeneous Multi-core, Multi-memory Systems

Energy Technology Data Exchange (ETDEWEB)

Su, Chun-Yi [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

2014-12-16

By 2004, microprocessor design focused on multicore scaling—increasing the number of cores per die in each generation—as the primary strategy for improving performance. These multicore processors typically equip multiple memory subsystems to improve data throughput. In addition, these systems employ heterogeneous processors such as GPUs and heterogeneous memories like non-volatile memory to improve performance, capacity, and energy efficiency. With the increasing volume of hardware resources and system complexity caused by heterogeneity, future systems will require intelligent ways to manage hardware resources. Early research to improve performance and energy efficiency on heterogeneous, multi-core, multi-memory systems focused on tuning a single primitive or at best a few primitives in the systems. The key limitation of past efforts is their lack of a holistic approach to resource management that balances the tradeoff between performance and energy consumption. In addition, the shift from simple, homogeneous systems to these heterogeneous, multicore, multi-memory systems requires in-depth understanding of efficient resource management for scalable execution, including new models that capture the interchange between performance and energy, smarter resource management strategies, and novel low-level performance/energy tuning primitives and runtime systems. Tuning an application to control available resources efficiently has become a daunting challenge; managing resources in automation is still a dark art since the tradeoffs among programming, energy, and performance remain insufficiently understood. In this dissertation, I have developed theories, models, and resource management techniques to enable energy-efficient execution of parallel applications through thread and data management in these heterogeneous multi-core, multi-memory systems. I study the effect of dynamic concurrent throttling on the performance and energy of multi-core, non-uniform memory access

F.B.R. Core mock-up RAPSODIE - II - numerical models

International Nuclear Information System (INIS)

Brochard, D.; Hammami, L.; Gantenbein, F.

1990-01-01

To study the behaviour of LMFBR cores excited by a seism, tests have been performed on the RAPSODIE core mock-up. The aim of this paper is to present the numerical models used to interprete these tests and the comparisons between calculations and experimental results

Energetics of LMFBR core disruptive accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.

1979-01-01

In general, in the design of fast reactor systems, containment design margins are specified by investigating the response of the containment to core disruptive accidents. The results of these analyses are then translated into criteria which the designers must meet. Currently, uniform and agreed upon criteria are lacking, and in this time while they are being developed, the designer should be aware of the considerations which go into the particular criteria he must work with, and participate in their development. This paper gives an overview of the current state of the art in assessing core disruptive accidents and the design implications of this process. (orig.)

Hydrogen formation and control under postulated LMFBR accident conditions

International Nuclear Information System (INIS)

Armstrong, G.R.; Wierman, R.W.

1976-09-01

The objective of this study is to experimentally investigate the potential for autoignition and combustion of hydrogen-sodium mixtures which may be produced in LMFBR accidents. The purpose and ultimate usefulness of this work is to provide data that will establish the validity and acceptability of mechanisms inherent to the LMFBR that could either prevent or delay the accumulation of hydrogen gas to less than 4 percent (V) in the Reactor Containment Building (RCB) under accident conditions. The results to date indicate that sodium and sodium-hydrogen mixtures such as may be expected during LMFBR postulated accidents will ignite upon entering an air atmosphere and that the hydrogen present will be essentially all consumed until such time that the oxygen concentration is depleted

Effects of governing parameters on steady-state inter-wrapper flow in an LMFBR

International Nuclear Information System (INIS)

Moriya, Shoichi

2001-01-01

Hydraulic experiments were performed using a 1/8th scale rectangular model, based on a Japanese demonstration fast breeder reactor design, in order to study fundamental characteristics of interwrapper flows occurring under steady state conditions in an LMFBR. The steady state interwrapper flow of which direction was downward in the center region and upward in the peripheral region of a core barrel was observed because of the radial static pressure gradient in the upper part of the core barrel, produced by a core blockage effect resulting from an above core structure with a perforated skirt. Thermal stratification phenomena were moreover observed in the interwrapper region, created by the hot steady state interwrapper flow from an upper plenum and the cold leakage flow through the separated plate of the core barrel. The thermal interface was generated in higher part of the core barrel when the core blockage effect was smaller and Richardson number and the leakage flow rate ratio were larger. Significant temperature fluctuations occurred in the peripheral region of the core barrel, when the difference between the interface elevations in the center and peripheral regions of the core barrel was enough large. (author)

A Preliminary Design Study of Ultra-Long-Life SFR Cores having Heterogeneous Fuel Assemblies

Energy Technology Data Exchange (ETDEWEB)

Jung, GeonHee; You, WuSeung; Hong, Ser Gi [Kyung Hee University, Yongin (Korea, Republic of)

2016-10-15

The PWR and CANDU reactors have provided electricity for several decades in our country but they have produced lots of spent fuels and so the safe and efficient disposal of these spent fuels is one of the main issues in nuclear industry. This type ultra-long-life cores are quite efficient in terms of the amount of spent fuel generation per electricity production and they can be used as an interim storage for PWR or CANDU spent fuel over several tens of years if they use the PWR or CANDU spent fuel as the initial fuel. Typically, the previous works have considered radially homogeneous fuel assemblies in which only blanket or driver fuel rods are employed and they considered axially or radially heterogeneous core configurations with the radially homogeneous fuel assemblies. These core configurations result in the propagation of the power distribution which can lead to the significant temperature changes for each fuel assembly over the time. In this work, the radially heterogeneous fuel assemblies are employed in new ultra-long-life SFR (Sodium-cooled Fast Reactor) cores to minimize the propagation of power distribution by allowing the power propagation in the fuel assemblies. In this work, new small ultra-long life SFR cores were designed with heterogeneous fuel assemblies having both blanket and driver fuel rods to minimize the propagation of power distribution over the core by allowing power propagation from driver rods to blanket rods in fuel assemblies. In particular, high fidelity depletion calculation coupled with heterogeneous Monte Carlo neutron transport calculation was performed to assess the neutronic feasibility of the ultralong life cores. The results of the analysis showed that the candidate core has the cycle length of 77 EFPYs, a small burnup reactivity swing of 1590 pcm and acceptably small SVRs both at BOC and EOC.

Fueling method in LMFBR type reactors

International Nuclear Information System (INIS)

Kawashima, Katsuyuki; Inoue, Kotaro.

1985-01-01

Purpose: To extend the burning cycle and decrease the number of fuel exchange batches without increasing the excess reactivity at the initial stage of burning cycles upon fuel loading to an LMFBR type reactor. Method: Each of the burning cycles is divided into a plurality of burning sections. Fuels are charged at the first burning section in each of the cycles such that driver fuel assemblies and blanket assemblies or those assemblies containing neutron absorbers such as boron are distributed in mixture in the reactor core region. At the final stage of the first burning section, the blanket assemblies or neutron absorber-containing assemblies present in mixture are partially or entirely replaced with driver fuel assemblies depending on the number of burning sections such that all of them are replaced with the driver fuel assemblies till the start of the final burning section of the abovementioned cycle. The object of this invention can thus be attained. (Horiuchi, T.)

Status of LMFBR development project in Japan

International Nuclear Information System (INIS)

Nagane, G.; Akebi, M.; Matsuno, Y.

1987-01-01

Initiation of the LMFBR development project in Japan was decided by the Atomic Energy Commission of Japan in 1966. In 1967, the Power Reactor and Nuclear Fuel Development Corporation (PNC) was established to realize the project as a part of its tasks of a wide scope covering all the reseatch and development activities concerning fuel cycle. In the present paper the status of experimental fast reactor (Joyo), which is the first milestone of the LMFBR project, prototype fast reactor (Monju) and R and D activities supporting the project including that for larger LMFBRs in the future is described. (author)

Conceptual design study of LMFBR core with carbide fuel

International Nuclear Information System (INIS)

Tezuka, H.; Hojuyama, T.; Osada, H.; Ishii, T.; Hattori, S.; Nishimura, T.

1987-01-01

Carbide fuel is a hopeful candidate for demonstration FBR(DFBR) fuel from the plant cost reduction point of view. High thermal conductivity and high heavy metal content of carbide fuel lead to high linear heat rate and high breeding ratio. We have analyzed carbide fuel core characteristics and have clarified the concept of carbide fuel core. By survey calculation, we have obtained a correlation map between core parameters and core characteristics. From the map, we have selected a high efficiency core whose features are better than those of an oxide core, and have obtained reactivity coefficients. The core volume and the reactor fuel inventory are approximately 20% smaller, and the burn-up reactivity loss is 50% smaller compared with the oxide fuel core. These results will reduce the capital cost. The core reactivity coefficients are similar to the conventional oxide DFBR's. Therefore the carbide fuel core is regarded as safe as the oxide core. Except neutron fluence, the carbide fuel core has better nuclear features than the oxide core

LMFBR safety. 3. Review of current issues and bibliography of literature (1972--1974)

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1977-01-01

The report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1972 through 1974. The bibliography consists of approximately 1380 abstracts covering research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included

LMFBR safety. 5. Review of current issues and bibliography of literature (1975--1976)

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1977-01-01

The current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA), are discussed. Bibliographic information on worldwide LMFBRs relative to the development and safety of the breeder reactor is presented for the period 1975 through 1976. The bibliography consists of approximately 1618 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Keyword, author, and permuted-title indexes are included for completeness

LMFBR safety. 3. Review of current issues and bibliography of literature (1972--1974)

Energy Technology Data Exchange (ETDEWEB)

Buchanan, J.R.; Keilholtz, G.W.

1977-02-24

The report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1972 through 1974. The bibliography consists of approximately 1380 abstracts covering research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included.

LMFBR safety. 5. Review of current issues and bibliography of literature (1975--1976)

Energy Technology Data Exchange (ETDEWEB)

Buchanan, J.R.; Keilholtz, G.W.

1977-06-08

The current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA), are discussed. Bibliographic information on worldwide LMFBRs relative to the development and safety of the breeder reactor is presented for the period 1975 through 1976. The bibliography consists of approximately 1618 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Keyword, author, and permuted-title indexes are included for completeness.

LMFBR safety. 1. Review of current issues and bibliography of literature, 1960--1969

Energy Technology Data Exchange (ETDEWEB)

Buchanan, J.R.; Keilholtz, G.W.

1976-08-16

This report discusses the current status of liquid-metal fast breeder (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1960 through 1969. The bibliography consists of 1560 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness.

LMFBR safety. 1. Review of current issues and bibliography of literature, 1960--1969

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1976-01-01

This report discusses the current status of liquid-metal fast breeder (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1960 through 1969. The bibliography consists of 1560 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness

A technique for computing bowing reactivity feedback in LMFBR's

International Nuclear Information System (INIS)

Finck, P.J.

1987-01-01

During normal or accidental transients occurring in a LMFBR core, the assemblies and their support structure are subjected to important thermal gradients which induce differential thermal expansions of the walls of the hexcans and differential displacement of the assembly support structure. These displacements, combined with the creep and swelling of structural materials, remain quite small, but the resulting reactivity changes constitute a significant component of the reactivity feedback coefficients used in safety analyses. It would be prohibitive to compute the reactivity changes due to all transients. Thus, the usual practice is to generate reactivity gradient tables. The purpose of the work presented here is twofold: develop and validate an efficient and accurate scheme for computing these reactivity tables; and to qualify this scheme

F.B.R. Core mock-up RAPSODIE- I: Experimental analysis

International Nuclear Information System (INIS)

Brochard, D.; Buland, P.; Gantenbein, F.

1990-01-01

The main phenomena which influence the LMFBR core response to a seismic excitation are the fluid structure interaction and the impacts between subassemblies. To study the core behaviour, seismic tests have been performed on the core mock-up RAPSODIE with or without fluid and restraint ring and for different levels of excitation. This paper summarizes the results of these tests

A study on the core characteristics of the fact breed reactor

International Nuclear Information System (INIS)

Cho, M.; Ryu, K.G.; Soh, D.S.; Kim, Y.C.; Lee, K.W.; Kim, Y.I.; Lim, J.C.; Oh, K.B.

1983-01-01

In order to investigate equilibrium core characteristics of a large LMFBR, nuclear-thermal hydraulic and safety-related characteristics are considered for the equilbrium core of Super-Phenix 1. Using the nuclear computational system for a large LMFBR (KAERI-26G cross section library/1DX/2DB), bias factor of the effective multiplication factor, refueling pattern and enrichments of refueled fuel assemblies are determined. Nuclear characteristics such as criticality, power distribution, and breeding gain are also obtained for the initial core to the equilibrium core. Based on the assembly power distribution of the equilibrium core, coolant flow distributions are determined with the use of THI3D code. Temperature fields within the core assemblies and pressure drop across the core assemblies are also analyzed. In addition, the subchannel analysis of the hottest assembly under the steady state is performed with COBRA-IV-I code. Finally, transient behaviors of reactivity, power, and temperature due to the loss of flow accident without scram are considered and the boiling initiation time of coolant in the fuel assembly is determined for the equilibrium core with SACO code. (Author)

Pipe supports and anchors - LMFBR applications

International Nuclear Information System (INIS)

Anderson, M.J.

1983-06-01

Pipe design and support design can not be treated as separate disciplines. A coordinated design approach is required if LMFBR pipe system adequacy is to be achieved at a reasonable cost. It is particularly important that system designers understand and consider those factors which influence support train flexibility and thus the pipe system dynamic stress levels. The system approach must not stop with the design phase but should continue thru the erection and acceptance test procedures. The factors that should be considered in the design of LMFBR pipe supports and anchors are described. The various pipe support train elements are described together with guidance on analysis, design and application aspects. Post erection acceptance and verification test procedures are then discussed

Detailed design consideration on wire-spaced LMFBR fuel subassemblies under the effects of uncertainties and non-nominal geometries

International Nuclear Information System (INIS)

Hishida, H.

1979-01-01

This paper explains some analytical methods for evaluating the effects of deviation in subchannel coolant flow rate from the nominal value due to fuel pin bundle deflection and manufacturing tolerances and of inter-sub-channel coolant mixing and local temperature rise due to a wire-spacer on the hot spot temperature. Numerical results are given in each chapter with respect to a prototype LMFBR core. (author)

Work plan: transient release from LMFBR fuel

International Nuclear Information System (INIS)

Kress, T.S.; Parker, G.W.; Fontana, M.H.

1975-09-01

The proposed LMFBR Transient Release Program at ORNL is designed to investigate, by means of ex-reactor experiments and analytical modeling, the release and transport of fuel, fission products, and transuranic elements from fast reactor cores in the event of certain hypothetical accidents. It is desired to experimentally produce energy depositions that are characteristic of severe hypothetical reactor transients by the application of direct electrical current to mixed-oxide fuels under sodium. The experimental program includes tests with and without sodium, investigations of alternative methods of generating fuel and sodium aerosols, the use of UO 2 as a fuel simulant, additions of tracers as fission product simulants, effects of radiation, and under-water and under-sodium efforts to study the behavior of the vapor bubble itself. Analytical modeling will accompany all phases of the program, and the data will be correlated with models developed. 21 references. (auth)

Heterogeneous recycling in SFR core periphery

International Nuclear Information System (INIS)

Varaine, Frederic; Buiron, Laurent; Boucher, Lionel; Chabert, Christine

2008-01-01

development, based on the one hand on the solutions offered by the existing fleet (reprocessing, fabrication and NPP) and on the other hand on the solutions offered by the future reactors of fourth generation. The scenario study considers the French nuclear park with a constant nuclear energy demand at 430 TWhe / year. The current nuclear park is replaced between 2020 and 2050 by a mixed nuclear park: 66 % of Generation III EPR reactors and 33% of Generation IV SFR. From 2080 to 2100, the EPR are replaced by SFR. The Plutonium is recycled in the fissile part of the SFR core. The separation of the minor actinides at the reprocessing step starts in 2038. The minor actinides are recycled in the radial blankets of the SFR from 2040 (10% content of MA). Those calculations are performed by the COSI code. The results indicate that the minor actinides inventory can be stabilized with the heterogeneous mode of transmutation using minor actinides in the radial blankets of the SFR. A minor actinides rate around 10% in the radial blankets is sufficient with the condition to involve 100 % of the SFR in the transmutation process. The minor actinides multi-recycling on a depleted uranium oxide matrix in radial blankets of SFR showed good results in terms of transmutation performances. This heterogeneous model allows a massive minor actinides loading while having almost no consequence on the core safety parameters and core fuel management. Two MA enrichment targets have been studied: an ambitious 40% case and a more realistic 10% case. The design of such assembly has to deal with criteria implying multi-physics analysis. The 10% MA content seems a good balance between transmutation performances and back/front end impact (neutrons source, decay heat,..) compared to the 40% content. Investigations, such as dedicated experimental material and fuel irradiation programs, are under process at CEA to set a global vision of an optimized system that can answer all these problems. (authors)

Hypothetical core disruptive accident analysis of a 2000 MWsub(e) liquid metal cooled fast breeder reactor

International Nuclear Information System (INIS)

Struwe, D.

1977-12-01

A structural phase diagram for hypothetical core disruptive accidents (HCDA) has been developed based on a variety of analyses for different LMFBR's. The intention was to identify the strategic phases of HCDA's important with regard to safety aspects of the plant. These phases are investigated in detail for a 2,000 MWsub(e) LMFBR (SNR-2,000). Characteristic data of SNR-2,000 are discussed concerning their influence on safety analysis. Reasons for the choice of model parameters for special phenomena as fuel coolant interaction, fuel pin failure mechanisms and sodium voiding are given. The results of calculations with CAPRI-2, HOPE and KADIS are analyzed for possibilities to enter energetic core disassembly with consequences, making power values below 2,000 MWsub(e) necessary. Investigation of these results shows that the expected consequences do not lead to design requirements, restricting the magnitude of the electrical power output of LMFBR's to values below 2,000 MWsub(e). Therefore, consequences of HCDA's are principal not expected to limit the feasibility of conventional core design of this order of magnitude. (orig.) [de

Chemical factors affecting fission product transport in severe LMFBR accidents

International Nuclear Information System (INIS)

Wichner, R.P.; Jolley, R.L.; Gat, U.; Rodgers, B.R.

1984-10-01

This study was performed as a part of a larger evaluation effort on LMFBR accident, source-term estimation. Purpose was to provide basic chemical information regarding fission product, sodium coolant, and structural material interactions required to perform estimation of fission product transport under LMFBR accident conditions. Emphasis was placed on conditions within the reactor vessel; containment vessel conditions are discussed only briefly

An homogeneization method applied to the seismic analysis of LMFBR cores

International Nuclear Information System (INIS)

Brochard, D.; Hammami, L.

1991-01-01

Important structures like nuclear reactor cores, steam generator bundle, are schematically composed by a great number of beams, immersed in a fluid. The fluid structure interaction is an important phenomenon influencing the dynamical response of bundle. The study of this interaction through classical methods would need a refined modelisation at the scale of the beams and lead to important size of problems. The homogeneization method constitutes an alternative approach if we are mainly interested by the global behaviour of the bundle. Similar approaches have been already used for other types of industrial structures (Sanchez-Palencia 1980, Bergman and al. 1985, Theodory 1984, Benner and al. 1981). This method consists in replacing the physical heterogeneous medium by an homogeneous medium, which characteristics are determined from the resolution of a set problems on the elementary cell. In the first part of this paper the main assumptions of the method will be summarized. Moreover, other important phenomena may contribute to the dynamical behaviour of the industrial above mentioned structures: those are the impacts between the beams. These impacts could be due to supports limiting the displacements of the beams or to differences in the vibratory characteristics of the various beams. The second part of the paper will concern the way of taking into account the impacts in the linear hemogeneous formalism. Finally an application to the seismic analysis of the FBR core mock-up RAPSODIE will be presented

Automated and Assistive Tools for Accelerated Code migration of Scientific Computing on to Heterogeneous MultiCore Systems

Science.gov (United States)

2017-04-13

AFRL-AFOSR-UK-TR-2017-0029 Automated and Assistive Tools for Accelerated Code migration of Scientific Computing on to Heterogeneous MultiCore Systems ...2012, “ Automated and Assistive Tools for Accelerated Code migration of Scientific Computing on to Heterogeneous MultiCore Systems .” 2. The objective...2012 - 01/25/2015 4. TITLE AND SUBTITLE Automated and Assistive Tools for Accelerated Code migration of Scientific Computing on to Heterogeneous

HardwareSoftware Co-design for Heterogeneous Multi-core Platforms The hArtes Toolchain

CERN Document Server

2012-01-01

This book describes the results and outcome of the FP6 project, known as hArtes, which focuses on the development of an integrated tool chain targeting a heterogeneous multi core platform comprising of a general purpose processor (ARM or powerPC), a DSP (the diopsis) and an FPGA. The tool chain takes existing source code and proposes transformations and mappings such that legacy code can easily be ported to a modern, multi-core platform. Benefits of the hArtes approach, described in this book, include: Uses a familiar programming paradigm: hArtes proposes a familiar programming paradigm which is compatible with the widely used programming practice, irrespective of the target platform. Enables users to view multiple cores as a single processor: the hArtes approach abstracts away the heterogeneity as well as the multi-core aspect of the underlying hardware so the developer can view the platform as consisting of a single, general purpose processor. Facilitates easy porting of existing applications: hArtes provid...

Measurements of dynamic shape factors of LMFBR aggregate aerosols

International Nuclear Information System (INIS)

Allen, M.D.; Moss, O.R.; Briant, J.K.

1980-01-01

Dynamic shape factors for branched, chain-like aggregates of LMFBR mixed-oxide fuels have been measured with a LAPS spiral-duct centrifuge. The aerosol was generated by repeatedly pulsing a focused laser beam onto the surface of a typical LMFBR fuel pellet. The measured values of the dynamic shape factor, corrected for slip, vary between kappa = 3.60 at D/sub ae/ = 0.5 μm, and kappa = 2.23 at D/sub ae/ = 1.5 μm

Accident considerations in LMFBR design

International Nuclear Information System (INIS)

Simpson, D.E.; Alter, H.; Fauske, H.K.; Hikido, K.; Keaten, R.W.; Stevenson, M.G.; Strawbridge, L.

1975-12-01

LMFBR safety design criteria are discussed from the standpoints of accident severity classification and damage criteria, and the following design events are considered: fuel failure propagation, reactivity addition faults, heat transport system events, steam generator faults, sodium spills, fuel handling and storage faults, and external events

Fuel pin response to an overpower transient in an LMFBR

International Nuclear Information System (INIS)

Grosberg, A.J.; Head, J.L.

1979-01-01

This paper describes a method by which the ability of a whole-core code accurately to predict the time and location of the first fuel pin failures may be tested. The method involves the use of a relatively simple whole-core code to 'drive' a sophisticated fuel pin code, which is far too complex to be used within a whole-core code but which is potentially capable of modelling reliably the response of an individual fuel pin. The method cannot follow accurately the subsequent course of the transient because the simple whole-core code does not model the reactivity effects of events which may follow pin failure. The codes used were the simple whole-core code FUTURE and the fuel pin behaviour code FRUMP. The paper describes an application of the method to analyse a hypothetical LMFBR accident in which the control rods were assumed to be driven from the core at maximum speed, with all trip circuits failed. Taking 0.5% clad strain as a clad failure criterion, failure was predicted to occur at the top of the active core at about 10s into the transient. A repeat analysis, using an alternative clad yield criterion which is thought to be more realistic, indicated failure at the same position but 24s into the transient. This is after the onset of sodium boiling. Pin failure at the top of the core are likely to cause negative reactivity changes. In this hypothetical accident, pin failures are likely, therefore, to have a moderating effect on the course of the transient. (orig.)

LMFBR: safety aspects

International Nuclear Information System (INIS)

Natta, M.

1990-01-01

This presentation of LMFBR safety is limited at Super Phenix reactor. After a brief description of the reactor, some details on safety systems, in normal or accidental conditions, are given. The main functions studied are: chain reaction trip, residual power evacuation, reactor containment. In heavy accident the behaviour of Super Phenix is studied which its particular characteristics and the possibilities of operators reactions. The probability of appearance and the maximum consequences of heavy accidents are given [fr

Safety consequences of local initiating events in an LMFBR

Energy Technology Data Exchange (ETDEWEB)

Crawford, R.M.; Marr, W.W.; Padilla, A. Jr.; Wang, P.Y.

1975-12-01

The potential for fuel-failure propagation in an LMFBR at or near normal conditions is examined. Results are presented to support the conclusion that although individual fuel-pin failure may occur, rapid failure-propagation spreading among a large number of fuel pins in a subassembly is unlikely in an operating LMFBR. This conclusion is supported by operating experience, mechanistic analyses of failure-propagation phenomena, and experiments. In addition, some of the consequences of continued operation with defected fuel are considered.

Safety consequences of local initiating events in an LMFBR

International Nuclear Information System (INIS)

Crawford, R.M.; Marr, W.W.; Padilla, A. Jr.; Wang, P.Y.

1975-12-01

The potential for fuel-failure propagation in an LMFBR at or near normal conditions is examined. Results are presented to support the conclusion that although individual fuel-pin failure may occur, rapid failure-propagation spreading among a large number of fuel pins in a subassembly is unlikely in an operating LMFBR. This conclusion is supported by operating experience, mechanistic analyses of failure-propagation phenomena, and experiments. In addition, some of the consequences of continued operation with defected fuel are considered

Using PKiKP coda to study heterogeneity in the top layer of the inner core's western hemisphere

Science.gov (United States)

Wu, Wenbo; Irving, Jessica C. E.

2017-05-01

Significant lateral and depth variations of the inner core's properties, such as the large-scale hemispherical pattern, have been confirmed by a variety of seismological observations. However it is still unclear which dynamic processes in the core are responsible for these variations. Small-scale volumetric heterogeneity has been detected in the top layer of the inner core by PKiKP coda observations. Studies of these small-scale heterogeneities can provide critical information, such as the degree of alignment of iron crystals, the presence of possible partial melt and the grain size of iron crystals, all of which can be used to constrain the dynamic processes of the inner core. However, most previous observations sampled the inner core beneath the Pacific Ocean and Asia, often in the inner core's 'eastern hemisphere'. We use seismic stations in the North America, including the Earthscope Transportable Array, to look at PKiKP and its coda waves. We find 21 events with clear signals. In agreement with previous studies, inner core scattering (ICS), resulting in clear PKiKP coda, is found at epicentral distances of 60°-95°. However, the ICS we observe in these 21 western hemisphere events is weaker than previously reported for the eastern hemisphere. Comparing our observations with numerical simulations, we conclude that this relatively weak ICS indicates small-scale heterogeneity in at least the top layer of the inner core beneath Central America. Combining our clear observations with previous studies suggests either a hemispherical difference, or a regional variation, of small-scale heterogeneity in the inner core.

LMFBR safety. 2. Review of current issues and bibliography of literature, 1970--1972

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1976-01-01

This report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1970 through 1972. The bibliography consists of approximately 1620 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness

LMFBR safety. 4. Review of current issues and bibliography of literature (1974--1975)

Energy Technology Data Exchange (ETDEWEB)

Buchanan, J.R.; Keilholtz, G.W.

1977-03-21

This report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1974 through 1975. The bibliography consists of approximately 1554 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness.

LMFBR safety. 4. Review of current issues and bibliography of literature (1974--1975)

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1977-01-01

This report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1974 through 1975. The bibliography consists of approximately 1554 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness

LMFBR safety. 2. Review of current issues and bibliography of literature, 1970--1972

Energy Technology Data Exchange (ETDEWEB)

Buchanan, J.R.; Keilholtz, G.W.

1976-11-22

This report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development and one of the principal safety issues, a hypothetical core-disruptive accident (HCDA). Bibliographic information on worldwide LMFBRs relative to the development of the breeder reactor as a safe source of nuclear power is presented for the period 1970 through 1972. The bibliography consists of approximately 1620 abstracts covering early research and development and operating experiences leading up to the present design practices that are necessary for the licensing of breeder reactors. Key-word, author, and permuted-title indexes are included for completeness.

System seismic analysis of an innovative primary system for a large pool type LMFBR plant

International Nuclear Information System (INIS)

Pan, Y.C.; Wu, T.S.; Cha, B.K.; Burelbach, J.; Seidensticker, R.

1984-01-01

The system seismic analysis of an innovative primary system for a large pool type liquid metal fast breeder reactor (LMFBR) plant is presented. In this primary system, the reactor core is supported in a way which differs significantly from that used in previous designs. The analytical model developed for this study is a three-dimensional finite element model including one-half of the primary system cut along the plane of symmetry. The model includes the deck and deck mounted components,the reactor vessel, the core support structure, the core barrel, the radial neutron shield, the redan, and the conical support skirt. The sodium contained in the primary system is treated as a lumped mass appropriately distributed among various components. The significant seismic behavior as well as the advantages of this primary system design are discussed in detail

Studies of spatial decoupling in heterogeneous LMFBR critical assemblies

International Nuclear Information System (INIS)

Brumbach, S.B.; Goin, R.W.; Carpenter, S.G.

1984-01-01

Recent measurements at the Zero Power Plutonium Reactor have studied the spatial decoupling in large, heterogeneous assemblies. These assemblies exhibited a significantly greater degree of decoupling than previous homogeneous assemblies of similar size. The flux distributions in these heterogeneous assemblies were very sensitive reactivity perturbations, and perturbed flux distributions were achieved relatively slowly. Decoupling was investigated using rod-drop, boron-oscillator and noise-coherence techniques which emphasized different times following the perturbations. Reactivity changes could be measured by analyzing the power history from a single detector using inverse kinetics methods with the assumption of an instantaneous efficiency change for the detector. For assemblies more decoupled than ZPPR-13, the instantaneous efficiency change assumption begins to be invalid

Development of 2-D/1-D fusion method for three-dimensional whole-core heterogeneous neutron transport calculations

International Nuclear Information System (INIS)

Lee, Gil Soo

2006-02-01

To describe power distribution and multiplication factor of a reactor core accurately, it is necessary to perform calculations based on neutron transport equation considering heterogeneous geometry and scattering angles. These calculations require very heavy calculations and were nearly impossible with computers of old days. From the limitation of computing power, traditional approach of reactor core design consists of heterogeneous transport calculation in fuel assembly level and whole core diffusion nodal calculation with assembly homogenized properties, resulting from fuel assembly transport calculation. This approach may be effective in computation time, but it gives less accurate results for highly heterogeneous problems. As potential for whole core heterogeneous transport calculation became more feasible owing to rapid development of computing power during last several years, the interests in two and three dimensional whole core heterogeneous transport calculations by deterministic method are increased. For two dimensional calculation, there were several successful approaches using even parity transport equation with triangular meshes, S N method with refined rectangular meshes, the method of characteristics (MOC) with unstructured meshes, and so on. The work in this thesis originally started from the two dimensional whole core heterogeneous transport calculation by using MOC. After successful achievement in two dimensional calculation, there were efforts in three-dimensional whole-core heterogeneous transport calculation using MOC. Since direct extension to three dimensional calculation of MOC requires too much computing power, indirect approach to three dimensional calculation was considered.Thus, 2D/1D fusion method for three dimensional heterogeneous transport calculation was developed and successfully implemented in a computer code. The 2D/1D fusion method is synergistic combination of the MOC for radial 2-D calculation and S N -like methods for axial 1

Airborne effluent control for LMFBR fuel reprocessing plants

International Nuclear Information System (INIS)

Yarbro, O.O.; Groenier, W.S.; Stephenson, M.J.

1976-01-01

A significant part of the LMFBR fuel reprocessing development program has been devoted to the development of efficient removal systems for the volatile fission products, including 131 I, krypton, tritium, 129 I, and most recently 14 C. Flowsheet studies have indicated that very significant reductions of radioactive effluents can be achieved by integrating advanced effluent control systems with new concepts of containment and ventilation; however, the feasibility of such has not yet been established, nor have the economics been examined. This paper presents a flowsheet for the application of advanced containment systems to the processing of LMFBR fuels and summarizes the status and applicability of specific fission product removal systems

Hydrogen jet recombination under postulated LMFBR accident conditions

International Nuclear Information System (INIS)

Wierman, R.W.

1977-01-01

Certain conditions may be postulated in LMFBR risk assessments for which the potential of hydrogen release to the reactor containment building needs to be evaluated. The inherent self-ignition characteristics of hydrogen jets entering the air atmosphere of the reactor containment building should be understood for such analyses. If hydrogen jets were to self-ignite (recombine) at the source where they enter the reactor containment building, then undesirable hydrogen accumulation would not occur. Therefore, experiments have been conducted investigating the phenomena associated with the recombination of hydrogen jets under conditions similar to those postulated for LMFBR studies. The data presented define the conditions required for self-ignition of the hydrogen jets

Status of gamma-ray heating characterization in LMFBR

International Nuclear Information System (INIS)

Gold, R.

1975-11-01

Efforts to define gamma-ray heating in Liquid Metal Fast Breeder Reactor (LMFBR) environments have been surveyed. Emphasis is placed on both current practice for the Experimental Breeder Reactor-II (EBR-II) and future needs of the Fast Flux Test Facility (FFTF). Experimental and theoretical work are included in this preliminary survey for both high and low power environments. Current ''state-of-the-art'' accuracies and limitations are assessed. On this basis, it is concluded that a broad and sustained effort be initiated to meet requested FFTF goal accuracies. To this end, recommendations are advanced for improving the current status of gamma heating characterization and temperature measurements in LMFBR

ZPR-6 assembly 7 high {sup 240}Pu core experiments : a fast reactor core with mixed (Pu,U)-oxide fuel and a centeral high{sup 240}Pu zone.

Energy Technology Data Exchange (ETDEWEB)

Lell, R. M.; Morman, J. A.; Schaefer, R.W.; McKnight, R.D.; Nuclear Engineering Division

2009-02-23

ZPR-6 Assembly 7 (ZPR-6/7) encompasses a series of experiments performed at the ZPR-6 facility at Argonne National Laboratory in 1970 and 1971 as part of the Demonstration Reactor Benchmark Program (Reference 1). Assembly 7 simulated a large sodium-cooled LMFBR with mixed oxide fuel, depleted uranium radial and axial blankets, and a core H/D near unity. ZPR-6/7 was designed to test fast reactor physics data and methods, so configurations in the Assembly 7 program were as simple as possible in terms of geometry and composition. ZPR-6/7 had a very uniform core assembled from small plates of depleted uranium, sodium, iron oxide, U{sub 3}O{sub 8} and Pu-U-Mo alloy loaded into stainless steel drawers. The steel drawers were placed in square stainless steel tubes in the two halves of a split table machine. ZPR-6/7 had a simple, symmetric core unit cell whose neutronic characteristics were dominated by plutonium and {sup 238}U. The core was surrounded by thick radial and axial regions of depleted uranium to simulate radial and axial blankets and to isolate the core from the surrounding room. The ZPR-6/7 program encompassed 139 separate core loadings which include the initial approach to critical and all subsequent core loading changes required to perform specific experiments and measurements. In this context a loading refers to a particular configuration of fueled drawers, radial blanket drawers and experimental equipment (if present) in the matrix of steel tubes. Two principal core configurations were established. The uniform core (Loadings 1-84) had a relatively uniform core composition. The high {sup 240}Pu core (Loadings 85-139) was a variant on the uniform core. The plutonium in the Pu-U-Mo fuel plates in the uniform core contains 11% {sup 240}Pu. In the high {sup 240}Pu core, all Pu-U-Mo plates in the inner core region (central 61 matrix locations per half of the split table machine) were replaced by Pu-U-Mo plates containing 27% {sup 240}Pu in the plutonium

PBDOWN - a computer code for simulating core material discharge and thermal to mechanical energy conversion in LMFBR hypothetical accidents

International Nuclear Information System (INIS)

Royl, P.

1981-01-01

PBDOWN is a computer code that simulates the blowdown of confined boiling materials ('pools') into a colder upper coolant plenum as time dependent ejection and expansion with consideration of a few selected exchange processes. Its application is restricted to situations resulting from hypothetical loss of flow (LOF) accidents in LMFBR's, where enough voiding has occured, that in core sodium vapor pressures become negligible. PBDOWN considers one working fluid for the discharge process (either fuel or steel) and a maximum of two working fluids (either fuel and sodium or steel and sodium) for the expansion process in the upper coolant plenum. Entrainment of sodium at the accelerated bubble liquid interfaces is mechanistically calculated by a Taylor instability entrainment model. Simulation of a hemispherical expansion form together with this mechanistic entrainment model gives a new integrated calculation of the time dependent sodium mass in the bubble. The paper summarizes the basic equations and assumptions of this computer model. Sample results compare different heat transfer and Na entrainment models during steel and fuel driven discharge processes. Mechanistic sodium entrainment simulation for SNR-type reactors coupled with a realistic heat transfer model is shown to reduce the integral mechanical work potential by a factor of 1.3 to 2.0 over the isentropic energy of the discharge working fluids. (orig.)

Role of fuel bubble phenomenology in assessment of LMFBR source term

International Nuclear Information System (INIS)

Cho, D.H.; Condiff, D.W.; Chan, S.H.

1985-01-01

Phenomenological aspects of a fuel vapor bubble formed in the sodium pool in a hypothetical severe accident are considered. The potential for fuel bubble collapse in the sodium pool is analyzed. It appears that for a wide range of hypothetical LMFBR accidents involving core vaporization, the fuel vapor bubble would likely be quenched and collapse prior to migration to the cover gas region. Such rapid quenching is due mainly to radiative heat transfer from the fuel bubble, coupled with the inherent capability of the sodium pool (large subcooling and high thermal conductivity) to dissipate thermal energy. Major uncertainty in the analysis concerns fuel vapor condensation phenomena at the sodium interface and its effect on the sodium surface radiation absorptivity. This is discussed in detail

Safety evaluation for the LMFBR plant using probabilistic risk assessment techniques

International Nuclear Information System (INIS)

Kani, Y.; Aizawa, K.

1987-01-01

This paper presents an application of probabilistic risk assessment techniques to a typical loop-type liquid metal fast breeder reactor (LMFBR) plant in the detailed design stage. A comprehensive systems analysis has been performed to identify event sequences leading to core damage and provide insights into the importance of accident contributors. While traditional event tree/fault tree modeling was used for the analysis, this study involved a thorough investigation of initiating events and of support system faults. The qualification of accident sequences has been conducted by combining the fault trees based on the event trees and obtaining sequence cut sets with the use of the SETS code. This study also attempted to quantify the potential for operator recovery actions in the course of each accident sequence. (author)

Compendium of computer codes for the safety analysis of LMFBR's

International Nuclear Information System (INIS)

1975-06-01

A high level of mathematical sophistication is required in the safety analysis of LMFBR's to adequately meet the demands for realism and confidence in all areas of accident consequence evaluation. The numerical solution procedures associated with these analyses are generally so complex and time consuming as to necessitate their programming into computer codes. These computer codes have become extremely powerful tools for safety analysis, combining unique advantages in accuracy, speed and cost. The number, diversity and complexity of LMFBR safety codes in the U. S. has grown rapidly in recent years. It is estimated that over 100 such codes exist in various stages of development throughout the country. It is inevitable that such a large assortment of codes will require rigorous cataloguing and abstracting to aid individuals in identifying what is available. It is the purpose of this compendium to provide such a service through the compilation of code summaries which describe and clarify the status of domestic LMFBR safety codes. (U.S.)

Power DRAC for rapid LMFBR deployment and consequent CO2 mitigation

International Nuclear Information System (INIS)

Schenewerk, W.E.

2006-01-01

A metallic-sodium LMFBR (Liquid Metal Fast Breeder Reactor) can control fuel temperature after a full power SCRAM using natural convection. A 3 percent nominal DRAC (Direct Reactor Auxiliary Cooling) does this without moving parts. DRAC is promoted from tertiary to primary decay heat removal, resulting in what is referred to as a Power DRAC. Power DRAC operates continuously before and after SCRAM, rejecting 3 per cent pile power. Power DRAC operability is validated by having it reject 75 MWt from a 2500 MWt pile at all times. IHX (Intermediate Heat Exchanger) is not required to be operable for primary, secondary, or tertiary core over temperature protection. Original DRAC concept (venturi DRAC) was a 1 per cent nominal tertiary decay heat removal system. Tertiary DRAC patent has expired. Power DRAC rejects 75 MWt through its own secondary sodium heat transfer loop to power a 25 MWe air Brayton cycle. Power DRAC eliminates requiring steam plant operability for decay heat removal. Intermediate sodium heat transfer system and steam plant can be optimized for maximum thermal efficiency. 2.5 GWt pile makes 1.0 GWe net power. Power DRAC maintains pile inlet and outlet temperatures while going from power to post-SCRAM conditions. Steam pressure is maintained post-SCRAM to mitigate SCRAM thermal transient. Not requiring steam plant operability for decay heat removal eases licensing and allows early LMFBR deployment. Each GWe atomic power delays Co2 doubling one week. (author)

Computer simulation of LMFBR piping systems

International Nuclear Information System (INIS)

A-Moneim, M.T.; Chang, Y.W.; Fistedis, S.H.

1977-01-01

Integrity of piping systems is one of the main concerns of the safety issues of Liquid Metal Fast Breeder Reactors (LMFBR). Hypothetical core disruptive accidents (HCDA) and water-sodium interaction are two examples of sources of high pressure pulses that endanger the integrity of the heat transport piping systems of LMFBRs. Although plastic wall deformation attenuates pressure peaks so that only pressures slightly higher than the pipe yield pressure propagate along the system, the interaction of these pulses with the different components of the system, such as elbows, valves, heat exchangers, etc.; and with one another produce a complex system of pressure pulses that cause more plastic deformation and perhaps damage to components. A generalized piping component and a tee branching model are described. An optional tube bundle and interior rigid wall simulation model makes such a generalized component model suited for modelling of valves, reducers, expansions, and heat exchangers. The generalized component and the tee branching junction models are combined with the pipe-elbow loop model so that a more general piping system can be analyzed both hydrodynamically and structurally under the effect of simultaneous pressure pulses

A Heterogeneous Multi-core Architecture with a Hardware Kernel for Control Systems

DEFF Research Database (Denmark)

Li, Gang; Guan, Wei; Sierszecki, Krzysztof

2012-01-01

Rapid industrialisation has resulted in a demand for improved embedded control systems with features such as predictability, high processing performance and low power consumption. Software kernel implementation on a single processor is becoming more difficult to satisfy those constraints. This pa......Rapid industrialisation has resulted in a demand for improved embedded control systems with features such as predictability, high processing performance and low power consumption. Software kernel implementation on a single processor is becoming more difficult to satisfy those constraints......). Second, a heterogeneous multi-core architecture is investigated, focusing on its performance in relation to hard real-time constraints and predictable behavior. Third, the hardware implementation of HARTEX is designated to support the heterogeneous multi-core architecture. This hardware kernel has...... several advantages over a similar kernel implemented in software: higher-speed processing capability, parallel computation, and separation between the kernel itself and the applications being run. A microbenchmark has been used to compare the hardware kernel with the software kernel, and compare...

THE LMFBR, key to the future

International Nuclear Information System (INIS)

Chipman, G.L. Jr.

1982-01-01

This survey explains the United States prospects for utilizing the LMFBR as a mean of meeting future energy demands. Nuclear option will represent a good financial investment only when breeder will be proved as a cost-effective option. International cooperation and combined programs are very helpful to develop breeder reactor power resource

Operating conditions of steam generators for LMFBR's

Energy Technology Data Exchange (ETDEWEB)

Ratzel, W

1975-07-01

Operating conditions considered to be appropriate for a LMFBR steam generator are discussed on the example of the SNR 300. The areas covered are steady state and transient conditions, upset and emergency temperature transients, and requirements due to sodium-water reactions. (author)

Operating conditions of steam generators for LMFBR's

International Nuclear Information System (INIS)

Ratzel, W.

1975-01-01

Operating conditions considered to be appropriate for a LMFBR steam generator are discussed on the example of the SNR 300. The areas covered are steady state and transient conditions, upset and emergency temperature transients, and requirements due to sodium-water reactions. (author)

Some characteristics of two heterogeneous cores and their experimental confirmation

International Nuclear Information System (INIS)

Giese, H.; Henneges, G.; Pilate, S.

1979-01-01

Heterogeneous core geometries have been investigated at the zero power facility ZEBRA with the objective of developing an improved understanding of the basic physics parameters of future non-conventional fast breeder reactors. Three assemblies were investigated, comprising similar fissile volumes and numbers of in-core fertile elements. First, BZC, a Salt-and-Pepper Core with fertile elements arranged in groups of sizes ranging from about one to eight power reactor subassemblies. Second, BZD, a Single Annular Core with the fertile elements collected to form a large central island of about 95 cm diameter, equivalent to about 36 subassemblies. Third, BZD/1A, a modified version of assembly BZD with a central island diameter of about 67 cm and an additional thin breeder ring. All assemblies used 24% Pu/Pu + U enriched fuel, with a core height of about 90 cm and a core diameter of about 200 cm. Extensive sodium voiding, flux-tilt and reactivity-interaction measurements have been carried out. The results indicate that relative to homogeneous designs a Single Annular arrangement yields a more marked improvement in sodium voiding performance than a Salt-and-Pepper arrangement, at the expense, however, of an increased sensitivity of the flux distribution to local reactivity perturbations. First analysis-level calculations on sodium-void yield C/E values with a significantly wider dispersion than in previous homogeneous assemblies. (author)

A heterogeneous multi-core platform for low power signal processing in systems-on-chip

DEFF Research Database (Denmark)

Paker, Ozgun; Sparsø, Jens; Haandbæk, Niels

2002-01-01

is based on message passing. The mini-cores are designed as parameterized soft macros intended for a synthesis based design flow. A 520.000 transistor 0.25µm CMOS prototype chip containing 6 mini-cores has been fabricated and tested. Its power consumption is only 50% higher than a hardwired ASIC and more......This paper presents a low-power and programmable DSP architecture - a heterogeneous multiprocessor platform consisting of standard CPU/DSP cores, and a set of simple instruction set processors called mini-cores each optimized for a particular class of algorithm (FIR, IIR, LMS, etc.). Communication...

Licensing decisions and safety research related to LMFBR accidents

International Nuclear Information System (INIS)

Denise, R.P.; Speis, T.P.; Kelber, C.N.; Curtis, R.T.

1977-01-01

The licensing approach which ensures adequate protection of the public health and safety against serious accidents is described. This paper describes the role of core melt and core disruptive accidents in the design, safety research, and licensing processes, using the Clinch River Breeder Reactor (CRBR) as a focal point. Major design attention is placed on the prevention of these accidents so that the probability of core melt accidents is reduced to a sufficiently low level that they are not treated as design basis accidents. Additional requirements are placed upon the design to further reduce residual risk. This licensing process is supported by a confirmatory research program designed to provide an independent basis for licensing judgements. It has as a goal the resolution of generic safety issues prior to the establishment of a commercial LMFBR industry. The program includes accident analysis, experiments in materials interactions, aerosol transport and system integrity and planning for new safety test facilities. The problems are approached in a multi-disciplinary functional manner that identifies key safety issues and centralizes efforts to resolve them. The near term objectives of the program support the licensing of the Clinch River Breeder Reactor (CRBR) and the proposed Prototype Large Breeder Reactor (PLBR). The long term objectives of the program support the licensing of commercial LMFBRs during the late 1980's and beyond. This safety research is designed to provide an independent basis for the licensing judgements which must be made by the Nuclear Regulatory Commission

Operational-safety advantages of LMFBR's: the EBR-II experience and testing program

International Nuclear Information System (INIS)

Sackett, J.I.; Lindsay, R.W.; Golden, G.H.

1982-01-01

LMFBR's contain many inherent characteristics that simplify control and improve operating safety and reliability. The EBR-II design is such that good advantage was taken of these characteristics, resulting in a vary favorable operating history and allowing for a program of off-normal testing to further demonstrate the safe response of LMFBR's to upsets. The experience already gained, and that expected from the future testing program, will contribute to further development of design and safety criteria for LMFBR's. Inherently safe characteristics are emphasized and include natural convective flow for decay heat removal, minimal need for emergency power and a large negative reactivity feedback coefficient. These characteristics at EBR-II allow for ready application of computer diagnosis and control to demonstrate their effectiveness in response to simulated plant accidents. This latter testing objective is an important part in improvements in the man-machine interface

Seismic response and damping tests of small bore LMFBR piping and supports

International Nuclear Information System (INIS)

Barta, D.A.; Anderson, M.J.; Severud, L.K.; Lindquist, M.R.

1984-01-01

Seismic testing and analysis of a prototypical Liquid Metal Fast Breeder Reactor (LMFBR) small bore piping system is described. Measured responses to simulated seismic excitations are compared with analytical predictions based on NRC Regulatory Guide 1.61 and measured system damping values. The test specimen was representative of a typical LMFBR insulated small bore piping system, and it was supported from a rigid test frame by prototypic dead weight supports, mechanical snubbers and pipe clamps

ISP: an optimal out-of-core image-set processing streaming architecture for parallel heterogeneous systems.

Science.gov (United States)

Ha, Linh Khanh; Krüger, Jens; Dihl Comba, João Luiz; Silva, Cláudio T; Joshi, Sarang

2012-06-01

Image population analysis is the class of statistical methods that plays a central role in understanding the development, evolution, and disease of a population. However, these techniques often require excessive computational power and memory that are compounded with a large number of volumetric inputs. Restricted access to supercomputing power limits its influence in general research and practical applications. In this paper we introduce ISP, an Image-Set Processing streaming framework that harnesses the processing power of commodity heterogeneous CPU/GPU systems and attempts to solve this computational problem. In ISP, we introduce specially designed streaming algorithms and data structures that provide an optimal solution for out-of-core multiimage processing problems both in terms of memory usage and computational efficiency. ISP makes use of the asynchronous execution mechanism supported by parallel heterogeneous systems to efficiently hide the inherent latency of the processing pipeline of out-of-core approaches. Consequently, with computationally intensive problems, the ISP out-of-core solution can achieve the same performance as the in-core solution. We demonstrate the efficiency of the ISP framework on synthetic and real datasets.

Feasibility study on large pool-type LMFBR

International Nuclear Information System (INIS)

1984-01-01

A feasibility study has been conducted from 1981 FY to 1983 FY, in order to evaluate the feasibility of a large pool-type LMFBR under the Japanese seismic design condition and safety design condition, etc. This study was aimed to establish an original reactor structure concept which meets those design conditions especially required in Japan. In the first year, preceding design concepts had been reviewed and several concepts were originated to be suitable to Japan. For typical two of them being selected by preliminary analysis, test programs were planned. In the second year, more than twenty tests with basic models had been conducted under severe conditions, concurrently analytical approaches were promoted. In the last year, larger model tests were conducted and analytical methods have been verified concerning hydrodynamic effects on structure vibration, thermo-hydraulic behaviours in reactor plena and so on. Finally the reactor structure concepts for a large pool-type LMFBR have been acknowledged to be feasible in Japan. (author)

ORNL experiments to characterize fuel release from the reactor primary containment in severe LMFBR accidents

International Nuclear Information System (INIS)

Wright, A.L.; Kress, T.S.; Smith, A.M.

1980-01-01

This paper presents results from aerosol source term experiments performed in the ORNL Aerosol Release and Transport (ART) Program sponsored by the US NRC. The tests described were performed to provide information on fuel release from an LMFBR primary containment as a result of a hypothetical core-disruptive accident (HCDA). The release path investigated in these tests assumes that a fuel/sodium bubble is formed after disassembly that transports fuel and fission products through the sodium coolant and cover gas to be relased into the reactor secondary containment. Due to the excellent heat transfer characteristics of the sodium, there is potential for large attenuation of the maximum release

Development of hybrid core calculation system using 2-D full-core heterogeneous transport calculation and 3-D advanced nodal calculation

International Nuclear Information System (INIS)

Sugimura, Naoki; Mori, Masaaki; Hijiya, Masayuki; Ushio, Tadashi; Arakawa, Yasushi

2004-01-01

This paper presents the Hybrid Core Calculation System which is a very rigorous but a practical calculation system applicable to best estimate core design calculations taking advantage of the recent remarkable progress of computers. The basic idea of this system is to generate the correction factors for assembly homogenized cross sections, discontinuity factors, etc. by comparing the CASMO-4 and SIMULATE-3 2-D core calculation results under the consistent calculation condition and then apply them for SIMULATE-3 3-D calculation. The CASMO-4 2-D heterogeneous core calculation is performed for each depletion step with the core conditions previously determined by ordinary SIMULATE-3 core calculation to avoid time consuming iterative calculations searching for the critical boron concentrations while treating the thermal hydraulic feedback. The final SIMULATE-3 3-D calculation using the correction factors is performed with iterative calculations searching for the critical boron concentrations while treating the thermal hydraulic feedback. (author)

A wet, heterogeneous lunar interior: Lower mantle and core dynamo evolution

Science.gov (United States)

Evans, A. J.; Zuber, M. T.; Weiss, B. P.; Tikoo, S. M.

2014-05-01

While recent analyses of lunar samples indicate the Moon had a core dynamo from at least 4.2-3.56 Ga, mantle convection models of the Moon yield inadequate heat flux at the core-mantle boundary to sustain thermal core convection for such a long time. Past investigations of lunar dynamos have focused on a generally homogeneous, relatively dry Moon, while an initial compositionally stratified mantle is the expected consequence of a postaccretionary lunar magma ocean. Furthermore, recent re-examination of Apollo samples and geophysical data suggests that the Moon contains at least some regions with high water content. Using a finite element model, we investigate the possible consequences of a heterogeneously wet, compositionally stratified interior for the evolution of the Moon. We find that a postoverturn model of mantle cumulates could result in a core heat flux sufficiently high to sustain a dynamo through 2.5 Ga and a maximum surface, dipolar magnetic field strength of less than 1 μT for a 350-km core and near ˜2 μT for a 450-km core. We find that if water was transported or retained preferentially in the deep interior, it would have played a significant role in transporting heat out of the deep interior and reducing the lower mantle temperature. Thus, water, if enriched in the lower mantle, could have influenced core dynamo timing by over 1.0 Gyr and enhanced the vigor of a lunar core dynamo. Our results demonstrate the plausibility of a convective lunar core dynamo even beyond the period currently indicated by the Apollo samples.

FBR type reactor core

International Nuclear Information System (INIS)

Tamiya, Tadashi; Kawashima, Katsuyuki; Fujimura, Koji; Murakami, Tomoko.

1995-01-01

Neutron reflectors are disposed at the periphery of a reactor core fuel region and a blanket region, and a neutron shielding region is disposed at the periphery of them. The neutron reflector has a hollow duct structure having a sealed upper portion, a lower portion opened to cooling water, in which a gas and coolants separately sealed in the inside thereof. A driving pressure of a primary recycling pump is lowered upon reduction of coolant flow rate, then the liquid level of coolants in the neutron reflector is lowered due to imbalance between the driving pressure and a gas pressure, so that coolants having an effect as a reflector are eliminated from the outer circumference of the reactor core. Therefore, the amount of neutrons leaking from the reactor core is increased, and negative reactivity is charged to the reactor core. The negative reactivity of the neutron reflector is made greater than a power compensation reactivity. Since this enables reactor scram by using an inherent performance of the reactor core, the reactor core safety of an LMFBR-type reactor can be improved. (I.N.)

Proceedings of the first analysis meeting on JUPITER-II Program

Energy Technology Data Exchange (ETDEWEB)

Shiradata, Keisho; Yamamoto, Masaaki [comps.

1984-12-31

The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.

Proceedings of the first analysis meeting on JUPITER-II Program

Energy Technology Data Exchange (ETDEWEB)

Shiradata, Keisho; Yamamoto, Masaaki [comps.

1985-12-31

The JUPITER-II Program is the Joint Physics Large Heterogeneous Core Critical Experiments Program between the U.S. Department of Energy (US DOE) and PNC, Japan. The experiments began in May 1982 and ended in April 1984, as a part of the ZPPR-13 program. The ZPPR-13 is a series of critical assemblies designed to study the fundamental neutronic behavior of large, radially-heterogeneous LMFBR cores. This report describes the results of analysis of ZPPR-13A and preliminary analysis of ZPPR-13B, and some topics of recent activities in fast reactor physics.

Hydrodynamic analysis of the LMFBR prompt burst excursion (PBE) experiment

International Nuclear Information System (INIS)

Young, M.F.

1977-01-01

A series of in-pile experiments has been conducted at Sandia Laboratories to provide information on pressure levels and conversion of thermal energy into mechanical work in LMFBR cores during hypothetical, superprompt-critical excursions. Pressures generated in these experiments are recorded by a pressure transducer located at the top and bottom of a sodium channel surrounding a single, fresh UO 2 fuel pin. Work energy conversion is measured by a linear motion transducer connected to a piston at the top of the sodium column. Since the pressure transducers are located fairly far from the location of pin failure, it becomes necessary to determine the effect of channel geometry and piston motion on the observed pressure data. A two-dimensional, hydrodynamic analysis of pressure pulse propagation in the fuel pin-coolant channel geometry was therefore performed using the CSQII computer code. The initial series of PBE experiments consists of single, fresh UO 2 pins surrounded by a sodium-filled or dry-coolant channel contained in a closed test capsule. The capsule is subjected to a maximum pulse in the Annular Core Pulse Reactor (ACPR) resulting in an energy deposition of from 2350 to 2900 J/g (14 and 20 percent enriched pins). The pulse width at half maximum (PWHM) is about 5 ms

LMFBR fuel-design environment for endurance testing, primarily of oxide fuel elements with local faults

International Nuclear Information System (INIS)

Warinner, D.K.

1980-01-01

The US Department of Energy LMFBR Lines-of-Assurance are briefly stated and local faults are given perspective with an historical review and definition to help define the constraints of LMFBR fuel-element designs. Local-fault-propagation (fuel-element failure-propagation and blockage propagation) perceptions are reviewed. Fuel pin designs and major LMFBR parameters affecting pin performance are summarized. The interpretation of failed-fuel data is aided by a discussion of the effects of nonprototypicalities. The fuel-pin endurance expected in the US, USSR, France, UK, Japan, and West Germany is outlined. Finally, fuel-failure detection and location by delayed-neutron and gaseous-fission-product monitors are briefly discussed to better realize the operational limits

Development of a simple estimation tool for LMFBR construction cost

International Nuclear Information System (INIS)

Yoshida, Kazuo; Kinoshita, Izumi

1999-01-01

A simple tool for estimating the construction costs of liquid-metal-cooled fast breeder reactors (LMFBRs), 'Simple Cost' was developed in this study. Simple Cost is based on a new estimation formula that can reduce the amount of design data required to estimate construction costs. Consequently, Simple cost can be used to estimate the construction costs of innovative LMFBR concepts for which detailed design has not been carried out. The results of test calculation show that Simple Cost provides cost estimations equivalent to those obtained with conventional methods within the range of plant power from 325 to 1500 MWe. Sensitivity analyses for typical design parameters were conducted using Simple Cost. The effects of four major parameters - reactor vessel diameter, core outlet temperature, sodium handling area and number of secondary loops - on the construction costs of LMFBRs were evaluated quantitatively. The results show that the reduction of sodium handling area is particularly effective in reducing construction costs. (author)

Simulation of LMFBR pump transients and comparison to LOF that occurred at EBR-II

International Nuclear Information System (INIS)

Koenig, F.F.; Dean, E.M.

1985-01-01

In a large LMFBR plant design, a number of pumps in parallel will feed the core. It must be demonstrated that the plant can continue to operate with the loss of one of the primary pumps. It is desirable not to have check valves in the loop from a reliability and economic standpoint. Simulations have been made to determine the consequences of a loss of one pump in a four-loop pool plant in which no plant protection action is taken. This analysis would be used to determine the required power rundown that would accompany pump loss. The two primary centrifugal pumps in EBR-II feed the core and blanket plenums in two parallel flow paths. The loss of one pump will result in decrease core flow and reverse flow through the down pump since no check valves are present in the system. For a large pool plant with four primary pumps, the loss of one pump will also result in reverse flow through the down pump if check valves of flow diodes are not included. The resulting flow transient has been modeled for EBR-II and the large plant using the DNSP program

Evaluation of Selected Resource Allocation and Scheduling Methods in Heterogeneous Many-Core Processors and Graphics Processing Units

Directory of Open Access Journals (Sweden)

Ciznicki Milosz

2014-12-01

Full Text Available Heterogeneous many-core computing resources are increasingly popular among users due to their improved performance over homogeneous systems. Many developers have realized that heterogeneous systems, e.g. a combination of a shared memory multi-core CPU machine with massively parallel Graphics Processing Units (GPUs, can provide significant performance opportunities to a wide range of applications. However, the best overall performance can only be achieved if application tasks are efficiently assigned to different types of processor units in time taking into account their specific resource requirements. Additionally, one should note that available heterogeneous resources have been designed as general purpose units, however, with many built-in features accelerating specific application operations. In other words, the same algorithm or application functionality can be implemented as a different task for CPU or GPU. Nevertheless, from the perspective of various evaluation criteria, e.g. the total execution time or energy consumption, we may observe completely different results. Therefore, as tasks can be scheduled and managed in many alternative ways on both many-core CPUs or GPUs and consequently have a huge impact on the overall computing resources performance, there are needs for new and improved resource management techniques. In this paper we discuss results achieved during experimental performance studies of selected task scheduling methods in heterogeneous computing systems. Additionally, we present a new architecture for resource allocation and task scheduling library which provides a generic application programming interface at the operating system level for improving scheduling polices taking into account a diversity of tasks and heterogeneous computing resources characteristics.

Monte-Carlo modeling of parameters of a subcritical cascade reactor based on MSBR and LMFBR technologies

International Nuclear Information System (INIS)

Bznuni, S.A.; Zhamkochyan, V.M.; Khudaverdyan, A.G.; Barashenkov, V.S.; Sosnin, A.N.; Polanski, A.

2001-01-01

Parameters are investigated of a subcritical cascade reactor driven by a proton accelerator and based on a primary lead-bismuth target, main reactor constructed analogously to the molten salt breeder (MSBR) reactor core and a booster-reactor analogous to the core of the BN-350 liquid metal cooled fast breeder reactor (LMFBR). It is shown by means of Monte-Carlo modeling that the reactor under study provides safe operation modes (k eff = 0.94 - 0.98), is capable to transmute effectively radioactive nuclear waste and reduces by an order of magnitude the requirements on the accelerator beam current. Calculations show that the maximal neutron flux in the thermal zone is 10 14 cm 12 · s -1 , in the fast booster zone is 5.12 · 10 15 cm 12 · s -1 at k eff = 0.98 and proton beam current I = 2.1 mA. (author)

Monte-Carlo Modeling of Parameters of a Subcritical Cascade Reactor Based on MSBR and LMFBR Technologies

CERN Document Server

Bznuni, S A; Zhamkochyan, V M; Polanski, A; Sosnin, A N; Khudaverdyan, A H

2001-01-01

Parameters of a subcritical cascade reactor driven by a proton accelerator and based on a primary lead-bismuth target, main reactor constructed analogously to the molten salt breeder (MSBR) reactor core and a booster-reactor analogous to the core of the BN-350 liquid metal cooled fast breeder reactor (LMFBR). It is shown by means of Monte-Carlo modeling that the reactor under study provides safe operation modes (k_{eff}=0.94-0.98), is apable to transmute effectively radioactive nuclear waste and reduces by an order of magnitude the requirements on the accelerator beam current. Calculations show that the maximal neutron flux in the thermal zone is 10^{14} cm^{12}\\cdot s^_{-1}, in the fast booster zone is 5.12\\cdot10^{15} cm^{12}\\cdot s{-1} at k_{eff}=0.98 and proton beam current I=2.1 mA.

Design considerations for epithermal pulse reactors

International Nuclear Information System (INIS)

Ostensen, R.W.

1978-01-01

Simplified design criteria were developed for scoping analyses of epithermal pulse reactors for use in LMFBR safety testing. By using these criteria, materials and designs were investigated to determine performance limits of moderately sized reactor cores. Several designs are suggested for further study. These are a gas-cooled core fueled with a heterogeneous mixture of Fe-UO 2 cermet and BeO-UO 2 ceramic fuels, and a heavy-water-cooled core fueled with an Fe-UO 2 cermet

A review of ANL base technology studies in support of the U.S. LMFBR vibration program

International Nuclear Information System (INIS)

Wambsganss, M.W.; Chen, S.S.; Mulcahy, T.M.; Shin, Y.S.

1977-01-01

Argonne National Laboratory (ANL) is the center for base technology studies of flow induced vibration for the U.S. LMFBR Program. This paper reviews and summarizes published results, reports on the status of ongoing programs, and discusses future needs as outlined in the U.S. LMFBR Vibrations Program Plan. (author)

A review of ANL base technology studies in support of the U.S. LMFBR vibration program

Energy Technology Data Exchange (ETDEWEB)

Wambsganss, M W; Chen, S S [Components Technology Division, Argonne National Laboratory, Argonne, IL (United States); Mulcahy, T M; Shin, Y S

1977-12-01

Argonne National Laboratory (ANL) is the center for base technology studies of flow induced vibration for the U.S. LMFBR Program. This paper reviews and summarizes published results, reports on the status of ongoing programs, and discusses future needs as outlined in the U.S. LMFBR Vibrations Program Plan. (author)

A study on cell heterogeneity effects in the Monju core. Evaluation using the continuous energy Monte Carlo code MVP

International Nuclear Information System (INIS)

Morohashi, Yuko; Ishibashi, Junichi; Nishi, Hiroshi

2002-03-01

The criticality analysis of the MONJU initial critical core was conducted based on conventional methods developed by the JUPITER program. Effective cross sections were created, considering self-shielding effects, from the JAERI Fast Set (JFS-3-J3.2); group constants in 70 energy groups, which were processed from the Japanese Evaluated Nuclear Data Library (JENDL-3.2). These were used in the standard calculation method: a 3-Dimensional Hexagonal-Z whole core calculation by diffusion theory. This standard calculation, however, involves several approximations. The continuous neutron energy spectrum is divided into 70 discrete energy groups and continuous spatial coordinates are represented by assembly-wise spatial meshes. Original transport equations are solved by diffusion theory (isotropic scattering) approximation and fine structures in fuel assemblies, such as fuel pins or wrapper tubes, are processed into cell-wise homogeneous mixture. To improve the accuracy of the results, these approximations are compensated for by applying corresponding correction factors. Cell heterogeneity effects, among them, were evaluated to be 0.3-0.4% Δk/kk' by diffusion calculations based on the group constants, obtained by heterogeneous cell model calculations. This method, however, has the drawback that it assumes that there is no interdependency of the related approximations; energy grouping, diffusion approximation, etc. A study on cell heterogeneity effects has been conducted using the continuous energy Monte Carlo method to validate the adequacy of this non-interdependency assumption. As a result, cell heterogeneity effects slightly larger than those from conventional methods have been obtained: 0.54% Δk/kk' for the initial critical core, and 0.50% Δk/kk' for the initial full power core. Dependency on plutonium enrichment and fuel temperature has also been identified, which implies the dependency of the cell heterogeneity effects on the specific core conditions. Grouping

Core level photoelectron spectroscopy probed heterogeneous xenon/neon clusters

International Nuclear Information System (INIS)

Pokapanich, Wandared; Björneholm, Olle; Öhrwall, Gunnar; Tchaplyguine, Maxim

2017-01-01

Binary rare gas clusters; xenon and neon which have a significant contrariety between sizes, produced by a co-expansion set up and have been studied using synchrotron radiation based x-ray photoelectron spectroscopy. Concentration ratios of the heterogeneous clusters; 1%, 3%, 5% and 10% were controlled. The core level spectra were used to determine structure of the mixed cluster and analyzed by considering screening mechanisms. Furthermore, electron binding energy shift calculations demonstrated cluster aggregation models which may occur in such process. The results showed that in the case of low mixing ratios of 3% and 5% of xenon in neon, the geometric structures exhibit xenon in the center and xenon/neon interfaced in the outer shells. However, neon cluster vanished when the concentration of xenon was increased to 10%. - Highlights: • Co-expansion setup is suitable for producing binary Xe/Ne clusters. • Appropriate temperature, pressure, and mixing ratios should be strictly controlled. • Low mixing ratio, Xe formed in the core and Xe/Ne interfacing in the outer shell. • High mixing ratio, only pure Xe clusters were detected.

Analytical model for transient fluid mixing in upper outlet plenum of an LMFBR

International Nuclear Information System (INIS)

Yang, J.W.; Agrawal, A.K.

1976-01-01

A two-zone mixing model based on the lumped-parameter approach was developed for the analysis of transient thermal response in the outlet plenum of an LMFBR. The maximum penetration of core flow is used as the criterion for dividing the sodium region into two mixing zones. The model considers the transient sodium temperature affected by the thermal expansion of sodium, heat transfer with cover gas, heat capacity of different sections of metal and the addition of by-pass flow into the plenum. The results of numerical calculations indicate that effects of flow stratification, chimney height, metal heat capacity and by-pass flow are important for transient sodium temperature calculation. Thermal expansion of sodium and heat transfer with the cover gas do not play any significant role on sodium temperature

LMFBR subassembly response to local pressure loadings: an experimental approach

International Nuclear Information System (INIS)

Marciniak, T.J.; Ash, J.E.; Marchertas, A.H.; Cagliostro, D.J.

1975-01-01

An experimental program to determine the response of LMFBR-type subassemblies to local subassembly accidents caused by pressure loadings is described. Some results are presented and compared with computer calculations

Development of 3-D FBR heterogeneous core calculation method based on characteristics method

International Nuclear Information System (INIS)

Takeda, Toshikazu; Maruyama, Manabu; Hamada, Yuzuru; Nishi, Hiroshi; Ishibashi, Junichi; Kitano, Akihiro

2002-01-01

A new 3-D transport calculation method taking into account the heterogeneity of fuel assemblies has been developed by combining the characteristics method and the nodal transport method. In the axial direction the nodal transport method is applied, and the characteristics method is applied to take into account the radial heterogeneity of fuel assemblies. The numerical calculations have been performed to verify 2-D radial calculations of FBR assemblies and partial core calculations. Results are compared with the reference Monte-Carlo calculations. A good agreement has been achieved. It is shown that the present method has an advantage in calculating reaction rates in a small region

Materials engineering issues, LMFBR steam generators

International Nuclear Information System (INIS)

Spalaris, C.N.; Challenger, K.D.; Day, R.A.; Dutina, D.; Ring, P.J.

1976-01-01

Selection of 2-1/4 Cr-1 Mo as the reference construction material for LMFBR steam generators assumed a balance between its known intrinsic properties and our ability to accommodate certain of its deficiencies through design allowance. A comprehensive development program was undertaken to define base data needed, confirm assumptions made relative to desired performance, minimize defects by optimization of melting, fabrication and heat treatment processes, and prepare specifications for purchasing reactor components

LMFBR safety experiment facility planning and analysis

International Nuclear Information System (INIS)

Stevenson, M.G.; Scott, J.H.

1976-01-01

In the past two years considerable effort has been placed on the planning and design of new facilities for the resolution of LMFBR safety issues. The paper reviews the key issues, the experiments needed to resolve them, and the design aspects of proposed new facilities. In addition, it presents a decision theory approach to selecting an optimal combination of modified and new facilities

Cover gas seals. 11 - FFTF-LMFBR seal-test program, January-March 1974

International Nuclear Information System (INIS)

Kurzeka, W.; Oliva, R.; Welch, F.

1974-01-01

The objectives of this program are to: (1) conduct static and dynamic tests to demonstrate or determine the mechanical performance of full-size (cross section) FFTF fuel transfer machine and reactor vessel head seals intended for use in a sodium vapor - inert gas environment, (2) demonstrate that these FFTF seals or new seal configuration provide acceptable fission product and cover gas retention capabilities at LMFBR Clinch River Plant operating environmental conditions other than radiation, and (3) develop improved seals and seal technology for the LMFBR Clinch River Plant to support the national objective to reduce all atmospheric contaminations to low levels

Upper shielding body in LMFBR type reactors

International Nuclear Information System (INIS)

Shoji, Koichi.

1986-01-01

Purpose: Preference is given to the strength and thermal insulation of a roof slab thereby ensuring axial size and improving the operationability upon inserting the control rod in the upper shielding body of LMFBR type reactors. Constitution: In an upper shielding body in which a large rotational plug is rotatably mounted to a circular hole formed at an eccentric position of a roof slab, while a small rotational plug is rotatably mounted to a circular hole disposed at an eccentric position of the large rotational plug and the reactor core upper mechanisms are supported on the small rotational plug, heat insulation layers are attached to the inside of the inner circumferential wall of the roof slab and the outer circumferential wall of the large rotational plug. By attaching the heat insulation layers, the heat conduction between the roof slab and the large rotational plug can be suppressed remarkably, by which occurrence of specific heat pass or local generation of large thermal stresses can be avoided even if difference is resulted to the temperature distribution between them. In this way, functions taking advantage of respective features of the roof slab and the small rotational plug can be obtained to achieve the purpose. (Kamimura, M.)

Some reliability targets affecting the necessary provisions for in-service inspection and monitoring of LMFBR engineering components

International Nuclear Information System (INIS)

Bolt, P.R.

1980-01-01

The possible consequences of failure of primary and secondary sodium circuit components are discussed with particular reference to post incident fault diagnosis, remedial procedures and outage durations. The core support structures and steam generator units are identified as particularly important components in terms of economic consequence of their failure. Important safety considerations may also apply. Levels of reliability for core support and steam generator integrity, necessary to meet economic and certain safety criteria, are discussed and quantitative data is given. Possible failure and deterioration mechanisms which could result in unacceptable reductions in reliability are then identified for the core support and steam generator units. Following a consideration of the reliability targets and possible causes of loss of reliability, an appraisal is made of the necessary extent of in-service data to be obtained on component behaviour and condition. In-service inspection and monitoring methods that could be used to obtain this data are described. Consideration is given to UK and overseas inspection experience on LMFBR and other nuclear plant. (author)

Some reliability targets affecting the necessary provisions for in-service inspection and monitoring of LMFBR engineering components

Energy Technology Data Exchange (ETDEWEB)

Bolt, P R [Fast Reactor Engineering, Plant Engineering Department, CEGB, Barnwood, Gloucester (United Kingdom)

1980-11-01

The possible consequences of failure of primary and secondary sodium circuit components are discussed with particular reference to post incident fault diagnosis, remedial procedures and outage durations. The core support structures and steam generator units are identified as particularly important components in terms of economic consequence of their failure. Important safety considerations may also apply. Levels of reliability for core support and steam generator integrity, necessary to meet economic and certain safety criteria, are discussed and quantitative data is given. Possible failure and deterioration mechanisms which could result in unacceptable reductions in reliability are then identified for the core support and steam generator units. Following a consideration of the reliability targets and possible causes of loss of reliability, an appraisal is made of the necessary extent of in-service data to be obtained on component behaviour and condition. In-service inspection and monitoring methods that could be used to obtain this data are described. Consideration is given to UK and overseas inspection experience on LMFBR and other nuclear plant. (author)

Flow-induced vibration in LMFBR steam generators: a state-of-the-art review

International Nuclear Information System (INIS)

Shin, Y.S.; Wambsganss, M.W.

1975-05-01

This state-of-the-art review identifies and discusses existing methods of flow-induced vibration analysis applicable to steam generators, their limitations, and base-technology needs. Also included are discussions of five different LMFBR steam-generator configurations and important design considerations, failure experiences, possible flow-induced excitation mechanisms, vibration testing, and available methods of vibration analysis. The objectives are to aid LMFBR steam-generator designers in making the best possible evaluation of potential vibration in steam-generator internals, and to provide the basis for development of design guidelines to avoid detrimental flow-induced vibration

Status of the LMFBR thermo- and fluid-dynamic activities at KFK

International Nuclear Information System (INIS)

Hoffmann, H.; Hofmann, F.; Rehme, K.

1979-01-01

The aim of the thermo- and fluiddynamic analysis is to determine the spatial velocity and temperature distributions in LMFBR-core elements with high accuracy. Knowledge of these data is a necessary prerequisite for determining the mechanical behavior of fuel rods and of structural material. Three cases are distinguished: Nominal geometry and steady state conditions; non-nominal geometry and quasi-steady state conditions; nominal geometry and non-steady state conditions. The present situation for the design calculations of fuel elements is based mainly on undisturbed normal operation. Most of the thermo- and fluiddynamic activities performed under the Fast Breeder Programme at KFK are related to this case. The present status of theoretical and experimental research work briefly presented in this paper, can be subdivided into the following main topics: 1. Physical and mathematical modelling of single phase rod bundle thermo- and fluiddynamics, 2. Experimental investigations on heat transfer and fluid flow in rod bundles

Neutronics characteristics of micro-heterogeneous ThO2-UO2 PWR cores

International Nuclear Information System (INIS)

Zhao, X.; Driscoll, M.J.; Kazimi, S.

2001-01-01

A new fuel concept, axially-micro-heterogeneous ThO 2 -UO 2 fuel, where ThO 2 fuel pellets and UO 2 fuel pellets are stacked in separate layers in the fuel rods, is being studied at MIT as an option to reduce plutonium production in LWR fuel. Very interesting neutronic behavior is observed: (1) A reactivity increase of 3% to 4% at EOL for a given 235 U inventory which results in a 20-30% increase in average core discharge burnup; (2) For certain configurations, a ''burnable poison'' effect is observed. Analysis shows that these effects are achieved due to a combination of changes in self-shielding, local fissile worth, and conversion ratio, among which self-shielding is the dominant effect at the end of a reactivity-limited burnup. Other variations of micro-heterogeneous UO 2 -ThO 2 fuel including duplex pellets, checkerboard pin distribution, and checkerboard-axial combinations have also been investigated, and their neutronic performance compared. It is concluded that the axial fuel micro-heterogeneity provides the largest gain in reactivity-limited burnup. (author)

LMFBR with booster pump in pumping loop

International Nuclear Information System (INIS)

Rubinstein, H.J.

1975-01-01

A loop coolant circulation system is described for a liquid metal fast breeder reactor (LMFBR) utilizing a low head, high specific speed booster pump in the hot leg of the coolant loop with the main pump located in the cold leg of the loop, thereby providing the advantages of operating the main pump in the hot leg with the reliability of cold leg pump operation

Control rod experiments in Racine

International Nuclear Information System (INIS)

Stanculescu, A.; Humbert, G.

1981-09-01

A survey of the control-rod experiments planned within the joint CEA/CNEN-DeBeNe critical experiment RACINE is given. The applicability to both heterogeneous and homogeneous large power LMFBR-cores is discussed. Finally, the most significant results of the provisional design calculations performed on behalf of the RACINE control-rod programme are presented

LMFBR post accident heat removal testing needs and conceptual design of a test facility

International Nuclear Information System (INIS)

Kleefeldt, K.; Kuechle, M.; Royl, P.; Werle, H.; Boenisch, G.; Heinzel, V.; Mueller, R.A.; Schramm, K.; Smidt, D.

1977-03-01

A study has been carried out in which the needs and requirements for a test facility were derived, enabling detailed investigation of key phenomena anticipated during the post accident heat removal (PAHR) phase as a consequence of a postulated LMFBR whole core accident. Part I of the study concentrates on demonstrating the PAHR phenomena and related testing needs. Three types of experiments were identified which require in-pile testing, ranging from 10 to 70 cm test bed diameter and correspondingly, 30 to 5 W/g minimum power density in the test fuel. In part II a conceptual design for a test facility is presented, emphasizing the capability for accomodating large test beds. This is achieved by a below-reactor-vessel testing device, neutronically coupled to a 100 MWt sodium cooled fast reactor. (orig.) [de

Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients. Progress report, March 1, 1977--May 31, 1977

International Nuclear Information System (INIS)

Todreas, N.E.; Golay, M.W.; Wolf, L.

1977-01-01

Progress is summarized in the following tasks: (1) bundle flow studies (wrapped and bare rods); (2) subchannel flow studies (bare rods); (3) LMFBR outlet plenum flow mixing; and (4) theoretical determination of local temperature fields in LMFBR fuel rod bundles

German position paper on structural analysis for LMFBR applications

International Nuclear Information System (INIS)

Angerbauer, A.; Link, F.

1983-01-01

During the design period of the German LMFBR, the SNR-300, extensive work had been done in the field of elastic and inelastic analysis. Furthermore, special design rules have been developed. A review of these activities and their state-of-the art is outlined in this paper

Design features affecting dynamic behaviour of fast reactor cores

International Nuclear Information System (INIS)

Kayser, G.; Gouriou, A.

1981-06-01

The study of dynamic response of an LMFBR to normal and accidental transients needs first of all a simulation code taking into account all the important effects. The DYN-1 code aims at this target. It represents with a sufficiently accurate meshing the core in a 20 geometry for the thermal and reactivity effects, while the kinetics of this core are calculated with a point model. The primary pool, secondary loops, steam generator are also represented, as well as the control and protective systems. We give a short description of this code. Simpler codes are sometimes good enough for parametric studies

Hardware concepts for a large low-energetics LMFBR core. Final report

International Nuclear Information System (INIS)

Hutter, E.; Batch, R.V.

1980-12-01

A design study was made to identify a practical set of hardware configurations that would embody the requirements developed in the numerical study of a low-energetics core and blanket for a prototype large breeder reactor. Dimensioned drawings are presented for fuel, blanket, reflector/shield, and control rod subassemblies. A horizontal cross section drawing shows how these subassemblies are arranged in the total core/blanket assembly. A core support is illustrated showing a dual plenums arrangement

LMFBR operational safety: the EBR-II experience

International Nuclear Information System (INIS)

Sackett, J.I.; Allen, N.L.; Dean, E.M.; Fryer, R.M.; Larson, H.A.; Lehto, W.K.

1978-01-01

The mission of the Experimental Breeder Reactor II (EBR-II) has evolved from that of a small LMFBR demonstration plant to a major irradiation-test facility. Because of that evolution, many operational-safety issues have been encountered. The paper describes the EBR-II operational-safety experience in four areas: protection-system design, safety-document preparation, tests of off-normal reactor conditions, and tests of elements with breached cladding

Heterogeneity of PTEN and ERG expression in prostate cancer on core needle biopsies: implications for cancer risk stratification and biomarker sampling.

Science.gov (United States)

Shah, Rajal B; Bentley, James; Jeffery, Zach; DeMarzo, Angelo M

2015-05-01

ERG and PTEN biomarkers are increasingly being analyzed on prostate core biopsies (NBXs); ERG as a marker of clonality and number of separately arising tumor foci and PTEN for prognostic information. Yet, in patients with multiple biopsy cores positive for cancer (PCa), there is no standardized approach for interrogation of these biomarkers in terms of the number of positive cores to evaluate. A total of 194 NBX cases containing more than one positive core with cancer were evaluated for ERG overexpression and PTEN loss by immunostaining (immunohistochemistry) of all positive cores. ERG overexpression or PTEN loss in at least one cancer core was present in 111 (57%) and 69 (36%) cases respectively. ERG overexpression was significantly associated with PTEN loss (P < .0001), and PTEN loss was associated with a high Gleason score (P < .0001). Inter- and intra-tumor core staining heterogeneity for ERG overexpression occurred in 42% and 5% cases and for PTEN loss both intra- and inter-tumor core heterogeneity was 68%. PTEN staining was highly discordant between PCa sites regardless of laterality. When the Gleason score was non-uniform across PCa sites, the combination of cores showing the highest Gleason score and largest tumor volume provided the best representation of ERG overexpression (92%) and PTEN loss (98%). When grades were uniform across cancer sites, the highest tumor volume core was generally representative of ERG overexpression (90%) but was less representative for PTEN loss (76%). Our results suggest that knowledge of this heterogeneity is critical for developing optimal yet cost-effective strategies to identify these underlying molecular abnormalities. Copyright © 2015 Elsevier Inc. All rights reserved.

Upon local blockage formations in LMFBR fuel rod bundles with wire-wrapped spacers

International Nuclear Information System (INIS)

Minden, C. v.; Schultheiss, G.F.

1982-01-01

A theoretical and experimental study, to improve understanding of local particle depositions in a wire-wrapped LMFBR fuel bundle, has been performed. Theoretical considerations show, that a preferentially axial process of particle depositions occurs. The experiments confirm this and clarify that the blockages arise near the particle source and settle at the spatially arranged minimum gaps in the bundle. The results suggest that, considering flow reduction, cooling and DND-detection, such fuel particle blockages are less dangerous. With reference to these safety-relevant factors, wire-wrapped LMFBR fuel bundles seem to gain advantages compared to the grid design. (orig.) [de

Input parameters to codes which analyze LMFBR wire-wrapped bundles

International Nuclear Information System (INIS)

Hawley, J.T.; Chan, Y.N.; Todreas, N.E.

1980-12-01

This report provides a current summary of recommended values of key input parameters required by ENERGY code analysis of LMFBR wire wrapped bundles. This data is based on the interpretation of experimental results from the MIT and other available laboratory programs

Determination of temperature distributions in fast reactor core coolants

International Nuclear Information System (INIS)

Tillman, M.

1975-04-01

An analytical method of determination of a temperature distribution in the coolant medium in a fuel assembly of a liquid-metal-fast-breeder-reactor (LMFBR) is presented. The temperature field obtained is applied for a constant velocity (slug flow) fluid flowing, parallel to the fuel pins of a square and hexagonal array assembly. The coolant subchannels contain irregular boundaries. The geometry of the channel due to the rod adjacent to the wall (edge rod) differs from the geometry of the other channels. The governing energy equation is solved analytically, assuming series solutions for the Poisson and diffusion equations, and the total solution is superposed by the two. The boundary conditions are specified by symmetry considerations, assembly wall insulation and a continuity of the temperature field and heat fluxes. The initial condition is arbitrary. The method satisfies the boundary conditions on the irregular boundaries and the initial condition by a least squares technique. Computed results are presented for various geometrical forms, with ratio of rod pitch-to-diameter typical for LMFBR cores. These results are applicable for various fast-reactors, and thus the influence of the transient solution (which solves the diffusion equation) on the total depends on the core parameters. (author)

LMFBR operational and experimental local-fault experience, primarily with oxide fuel elements

International Nuclear Information System (INIS)

Warinner, D.K.

1980-01-01

Case-by-case reviews of selective world experience with severe local faults, particularly fuel failure and fuel degradation, are reviewed for two sodium-cooled thermal reactors, several LMFBRs, and LMFBR-fuels experiments. The review summarizes fuel-failure frequency and illustrates the results of the most damaging LMFBR local-fault experiences of the last 20 years beginning with BR-5 and including DFR, BOR-60, BR2's MFBS- and Mol-loops experiments, Fermi, KNK, Rapsodie, EBR-II, and TREAT-D2. Local-fault accommodation is demonstrated and a need to more thoroughly investigate delayed-neutron and gaseous-fission-product signals is highlighted in view of uranate formation, observed blockages, and slow fuel-element failure-propagation

LMFBR Emergency Deployment Assuming 45 year Time-Delay Excess CO2 Removal

International Nuclear Information System (INIS)

Schenewerk, William Ernest

2008-01-01

Atmospheric CO 2 is presently increasing 2.25% per year in proportion to 2.25% per year exponential fossil fuel consumption increase. CO 2 removal is modeled as being proportional to 45-year-earlier CO 2 amount above 280 ppmV-C. This is: Exp (-0.0225/year * 45 years) = 0.36 fraction CO 2 removed from anthropological emissions, apparently by seawater. LMFBRs use 15 year doubling time. Deploying 30000 GWe atomic power by year-2080 results in CO 2 doubling year-2065 if World primary energy consumption continues increasing 2.25% per year. CO 2 remains roughly twice pre-industrial until year-2100. Beginning year-2080, CO 2 declines at 2.25% per year. CO 2 will presumably decline back to roughly the year-2000 value by year-2200 if the 45-year-delay sink remains effective. LMFBR and GCFR fleet expands to 30000 GWe by 2080. 1000 GWe LWR fleet consumes 5 Mt HM (Heavy Metal). Breeder first cores require 1 Mt HM. (author)

LMFBR technology. FFTF cover-gas leakage calculation

International Nuclear Information System (INIS)

Deboi, H.

1974-01-01

The FFTF LMFBR is intended to have a near zero release of radioactive gases during normal reactor operation with 1% failed fuel. This report presents calculations which provide an approximation of these cover gas leakages. Data from ongoing static and dynamic seal leak tests at AI are utilized. Leakage through both elastomeric and metallic seals in all sub-assemblies and penetrations comprising the reactor cover gas containment during reactor operation system are included

Core design methods for advanced LMFBRs

International Nuclear Information System (INIS)

Chandler, J.C.; Marr, D.R.; McCurry, D.C.; Cantley, D.A.

1977-05-01

The multidiscipline approach to advanced LMFBR core design requires an iterative design procedure to obtain a closely-coupled design. HEDL's philosophy requires that the designs should be coupled to the extent that the design limiting fuel pin, the design limiting duct and the core reactivity lifetime should all be equal and should equal the fuel residence time. The design procedure consists of an iterative loop involving three stages of the design sequence. Stage 1 consists of general mechanical design and reactor physics scoping calculations to arrive at an initial core layout. Stage 2 consists of detailed reactor physics calculations for the core configuration arrived at in Stage 1. Based upon the detailed reactor physics results, a decision is made either to alter the design (Stage 1) or go to Stage 3. Stage 3 consists of core orificing and detailed component mechanical design calculations. At this point, an assessment is made regarding design adequacy. If the design is inadequate the entire procedure is repeated until the design is acceptable

Implications and control of fuel-cladding chemical interaction for LMFBR fuel pin design

International Nuclear Information System (INIS)

Roake, W.E.

1977-01-01

Fuel-cladding-chemical-interaction (FCCI) is typically incorporated into the design of an LMFBR fuel pin as a wastage allowance. Several interrelated factors are considered during the evolution of an LMFBR fuel pin design. Those which are indirectly affected by FCCI include: allowable pin power, fuel restructuring, fission gas migration and release from the fuel, fuel cracking, fuel swelling, in-reactor cladding creep, cladding swelling, and the cladding mechanical strain. Chemical activity of oxygen is the most readily controlled factor in FCCI. Two methods are being investigated: control of total oxygen inventory by limiting fuel O/M, and control of oxygen activity with buffer metals

Implications and control of fuel-cladding chemical interaction for LMFBR fuel pin design

Energy Technology Data Exchange (ETDEWEB)

Roake, W E [Westinghouse-Hanford Co., Richland, WA (United States)

1977-04-01

Fuel-cladding-chemical-interaction (FCCI) is typically incorporated into the design of an LMFBR fuel pin as a wastage allowance. Several interrelated factors are considered during the evolution of an LMFBR fuel pin design. Those which are indirectly affected by FCCI include: allowable pin power, fuel restructuring, fission gas migration and release from the fuel, fuel cracking, fuel swelling, in-reactor cladding creep, cladding swelling, and the cladding mechanical strain. Chemical activity of oxygen is the most readily controlled factor in FCCI. Two methods are being investigated: control of total oxygen inventory by limiting fuel O/M, and control of oxygen activity with buffer metals.

Long-Haul Dense Space Division Multiplexed Transmission over Low-Crosstalk Heterogeneous 32-Core Transmission Line Using Partial Recirculating Loop System

DEFF Research Database (Denmark)

Mizuno, Takayuki; Shibahara, Kohki; Ye, Feihong

2017-01-01

In this paper, we present long-haul 32-core dense space division multiplexed (DSDM) unidirectional transmission over a single-mode multicore transmission line. We developed a low-crosstalk heterogeneous 32-core fiber with a square lattice arrangement, and a novel partial recirculating loop system...

Shielding plug for LMFBR type reactors

International Nuclear Information System (INIS)

Hashiguchi, Ko.

1979-01-01

Purpose: To enable effective removal of liquid metals deposited, if any, in the gaps between a rotary plug and a fixed plug in LMFBR type reactors. Constitution: A plate incorporated with a heater and capable of projecting in a gap between a rotary plug and a fixed plug, and a scraper connected in perpendicular to it are provided to the rotary plug. Solidified liquid metals such as sodium deposited in the gap are effectively removed by the heating with the heater and the scraping action due to the rotation. (Horiuchi, T.)

Future development LMFBR-steam generators SNR2

International Nuclear Information System (INIS)

Essebaggers, J.; Pors, J.G.

1975-01-01

The development work for steam generators for large LMFBR plants by Neratoom will be reviewed consisting of: 1. Development engineering information. 2. Concept select studies followed by conceptual designs of selected models. 3. Development manufacturing techniques. 4. Detail design of a prototype unit. 5. Testing of sub-constructions for prototype steam generators. In this presentation item 1 and 2 above will be high lighted, identifying the development work for the SNR-2 steam generators on short term basis. (author)

Single-phase sodium pump model for LMFBR thermal-hydraulic analysis

International Nuclear Information System (INIS)

Madni, I.K.; Cazzoli, E.G.; Agrawal, A.K.

1979-01-01

A single-phase, homologous pump model has been developed for simulation of safety-related transients in LMFBR systems. Pump characteristics are modeled by homologous head and torque relations encompassing all regimes of operation. These relations were derived from independent model test results with a centrifugal pump of specific speed equal to 35 (SI units) or 1800 (gpm units), and are used to analyze the steady-state and transient behavior of sodium pumps in a number of LMFBR plants. Characteristic coefficients for the polynomials in all operational regimes are provided in a tabular form. The speed and flow dependence of head is included through solutions of the impeller and coolant dynamic equations. Results show the model to yield excellent agreement with experimental data in sodium for the FFTF prototype pump, and with vendor calculations for the CRBR pump. A sample pipe rupture calculation is also performed to demonstrate the necessity for modeling the complete pump characteristics

Fuel penetration of intersubassembly gaps in LMFBRs: a calculational method with the SIMMER-II code

International Nuclear Information System (INIS)

DeVault, G.P.

1983-01-01

Early fuel removal from the active core of a liquid-metal-cooled fast breeder reactor (LMFBR) undergoing a core-disruptive accident may reduce the potential for large energetics resulting from recriticalities. A possible avenue for early fuel removal in heterogeneous core LMFBRs is the failure of duct walls in disrupted driver subassemblies followed by fuel penetration into the gaps between blanket subassemblies. The SIMMER-II code was modified to simulate flow between subassembly gaps. Calculations with the modified SIMMER-II code indicate the capabilities of the method and the potential for fuel mass reduction in the active core

In-core fuel disruption experiments simulating LOF accidents for homogeneous and heterogeneous core LMFBRs: FD2/4 series

International Nuclear Information System (INIS)

Wright, S.A.; Mast, P.K.; Schumacher, Gustav; Fischer, E.A.

1982-01-01

A series of Fuel Disruption (FD) experiments simulating LOF accidents transients for homogeneous- and heterogeneous-core LMFBRs is currently being performed in the Annular Core Research Reactor at SNL. The test fuel is observed with high-speed cinematography to determine the timing and the mode of the fuel disruption. The five experiments performed to date show that the timing and mode of fuel disruption depend on the power level, fuel temperature (after preheat and at disruption), and the fuel temperature gradient. Two basic modes of fuel disruption were observed; solid-state disruption and liquid-state swelling followed by slumping. Solid-state dispersive fuel behavior (several hundred degrees prior to fuel melting) is only observed at high power levels (6P 0 ), low preheat temperatures (2000 K), and high thermal gradients (2800 K/mm). The swelling/slumping behavior was observed in all cases near the time of fuel melting. Computational models have been developed that predict the fuel disruption modes and timing observed in the experiments

PHOEBUS/UHTREX: a preliminary study of a low-cost facility for transient tests of LMFBR fuel

International Nuclear Information System (INIS)

Kirk, W.L.

1976-08-01

The results of a brief preliminary design study of a facility for transient nuclear tests of fast breeder reactor fuel are described. The study is based on the use of a reactor building originally built for the UHTREX reactor, and the use of some reactor hardware and reactor design and fabrication technology remaining from the Phoebus-2 reactor of the Rover nulcear rocket propulsion program. The facility is therefore currently identified as the PHOEBUS/UHTREX facility. This facility is believed capable of providing early information regarding fast reactor core accident energetics issues which will be very valuable to the overall LMFBR safety program. Facility performance in conjunction with a reference 127-fuel pin experiment is described. Low cost and early availability of the facility were emphasized in the selection of design features and parameters

PHOEBUS/UHTREX: a preliminary study of a low-cost facility for transient tests of LMFBR fuel

Energy Technology Data Exchange (ETDEWEB)

Kirk, W.L. (comp.)

1976-08-01

The results of a brief preliminary design study of a facility for transient nuclear tests of fast breeder reactor fuel are described. The study is based on the use of a reactor building originally built for the UHTREX reactor, and the use of some reactor hardware and reactor design and fabrication technology remaining from the Phoebus-2 reactor of the Rover nulcear rocket propulsion program. The facility is therefore currently identified as the PHOEBUS/UHTREX facility. This facility is believed capable of providing early information regarding fast reactor core accident energetics issues which will be very valuable to the overall LMFBR safety program. Facility performance in conjunction with a reference 127-fuel pin experiment is described. Low cost and early availability of the facility were emphasized in the selection of design features and parameters.

An appreciation of the events, models and data used for LMFBR radiological source term estimations

International Nuclear Information System (INIS)

Keir, D.; Clough, P.N.

1989-01-01

In this report, the events, models and data currently available for analysis of accident source terms in liquid metal cooled fast neutron reactors are reviewed. The types of hypothetical accidents considered are the low probability, more extreme types of severe accident, involving significant degradation of the core and which may lead to the release of radionuclides. The base case reactor design considered is a commercial scale sodium pool reactor of the CDFR type. The feasibility of an integrated calculational approach to radionuclide transport and speciation (such as is used for LWR accident analysis) is explored. It is concluded that there is no fundamental obstacle, in terms of scientific data or understanding of the phenomena involved, to such an approach. However this must be regarded as a long-term goal because of the large amount of effort still required to advance development to a stage comparable with LWR studies. Particular aspects of LMFBR severe accident phenomenology which require attention are the behaviour of radionuclides during core disruptive accident bubble formation and evolution, and during the less rapid sequences of core melt under sodium. The basic requirement for improved thermal hydraulic modelling of core, coolant and structural materials, in these and other scenarios, is highlighted as fundamental to the accuracy and realism of source term estimations. The coupling of such modelling to that of radionuclide behaviour is seen as the key to future development in this area

Review of PRA methodology for LMFBR

International Nuclear Information System (INIS)

Yang, J. E.

1999-02-01

Probabilistic Risk Assessment (PRA) has been widely used as a tool to evaluate the safety of NPPs (Nuclear Power Plants), which are in the design stage as well as in operation. Recently, PRA becomes one of the licensing requirements for many existing and new NPPs. KALIMER is a Liquid Metal Fast Breeder Reactor (LMFBR) being developed by KAERI. Since the design concept of KALIMER is similar to that of the PRISM plant developed by GE, it would be appropriate to review the PRA methodology of PRISM as the first step of KALIMER PRA. Hence, in this report summarizes the PRA methodology of PRISM plant, and the required works for the PSA of KALIMER based on the reviewed results. The PRA technology of PRISM plant consists of following five major tasks: (1) development of initiating event list, (2) development of system event tree, (3) development of core response event tree, (4) development of containment response event tree, and (5) consequences and risk estimation. The estimated individual and societal risk measures show that the risk from a PRISM module is substantially less than the NRC goal. Each task is compared to the PRA methodology of Light Water Reactor (LWR)/Pressurized Heavy Water Reactor (PHWR). In the report, each task of PRISM PRA methodology is reviewed and compared to the corresponding part of LWR/PHWR PSA performed in Korea. The parts that are not modeled appropriately in PRISM PRA are identified, and the recommendations for KALIMER PRA are stated. (author). 14 refs., 9 tabs., 4 figs

Design approaches to achieve competitive LMFBR capital costs

International Nuclear Information System (INIS)

Arnold, W.H.; Ehrman, C.S.; Sharbaugh, J.E.; Young, W.H.

1982-01-01

Through analysis of the essential functional elements of an LMFBR, numerous ways were found to simplify system design, reduce the size of components and equipment, and eliminate some components and systems. The projected capital cost per net kW of this design is competitive with that of current PWRs. RandD programs and the construction and operation of CRBRP now are needed to prove out the features of this new design

LMBFR and LWR in-core thermal-hydraulic codes: the state-of-the-art and research and development needs

International Nuclear Information System (INIS)

Khan, E.U.; Coomes, E.P.; Rowe, D.S.; Trent, D.S.

1981-04-01

A review of analytical design methods used for predicting reactor core flow and temperature distributions is presented with emphasis on LMFBR's. The paper also briefly describes and contrasts the methods used for LWR's. These methods are global analysis, subchannel analysis, distributed parameter, and hybrid analysis. The evolution of the local and subchannel analysis methods is presented. Data used for code validation are also presented. Current research and development needs are identified and discussed. Areas identified for future research and development include methods and expermental data for analysis of distorted bundles and natural convection. Methods that have been developed for predicting the safety performance of LMFBR's and LWR's are not within the scope of this paper

Post-accident fuel relocation and heat removal in the LMFBR

International Nuclear Information System (INIS)

Kazimi, M.S.; Tsai, S.S.; Gasser, R.D.

1976-08-01

Assessment of the dynamics of post-accident fuel relocation and heat removal is an important aspect of the evaluation of the consequences of a hypothetical accident in an LMFBR. Such an assessment is of particular importance in the evaluation of the post-accident radiological doses around the reactor site. In the present evaluation particular attention is given to the design features of the Clinch River Breeder Reactor Plant (CRBR). Fuel relocation and heat removal, assuming certain conditions have resulted in core disruption, are discussed. The discussion of events and phenomena involved in the relocation processes is centered around the resulting patterns of heat source distribution. The factors influencing fuel relocation and distribution in the inlet and outlet plena of the reactor vessel are discussed. The current technology of in-vessel heat removal is applied to the design of the CRBR reactor. Both fuel debris cooling limits and overall coolant flow in the reactor under natural convection conditions are explored. Some of the uncertainties in ex-vessel fuel behavior are addressed. In particular, the effect of melting the cavity bed on the rate of growth of a molten fuel pool is investigated

Finite element analysis of irradiation-induced dilation of the fuel subassembly duct in LMFBR

International Nuclear Information System (INIS)

Gao Fuhai; Fu Hao; Li Nan; Yang Kongli; Wang Mingzhen

2013-01-01

Background: The calculation of irradiation-induced dilation of the fuel subassembly duct in LMFBR is important for fast reactor core design.. Purpose: To investigate how to calculate the dilation by using finite element method (FEM). Methods: First, irradiation-induced creep and swelling material models are introduced. Then, a theoretical solution based on a simplified bending plate model is briefly given. Finally, a stress update scheme for the adopted material models is presented and furthermore embedded into ABAQUS user interface UMAT to conduct finite element analysis. Both solutions are compared and discussed. Results: FEM successfully predicts the duct dilation and its solution agrees well with theoretical one in small deformation. Conclusions: The proposed stress update scheme is effective, The accuracy of the theory solution declines when dilation becomes larger. The maximum stress occurs at the duct corner point, and the location has stress relaxation effect. (authors)

LMFBR flexible pipe joint development program. Annual technical progress report, government fiscal year 1977

International Nuclear Information System (INIS)

1978-01-01

Currently, the ASME Boiler and Pressure Vessel Code does not allow the use of flexible pipe joints (bellows) in Section III, Class 1 reactor primary piping systems. Studies have shown that the primary piping loops of LMFBR's could be simplified by using these joints. This simplification translates directly into shorter primary piping runs and reduced costs for the primary piping system. Further cost savings result through reduced vault sizes and reduced containment building diameter. In addition, the use of flexible joints localizes the motions from thermally-induced piping growth into components which are specifically designed to accommodate this motion. This reduces the stress levels in the piping system and its components. It is thus economically and structurally important that flexible piping joints be available to the LMFBR designer. The overall objective of the Flexible Joint Program is to provide this availability. This will be accomplished through the development of ASME rules which allow the appropriate use of such joints in Section III, Class 1 piping systems and through the development and demonstration of construction methods which satisfy these rules. The rule development includes analytic and testing methodology formulations which will be supported by subscale bellows testing. The construction development and demonstration encompass the design, fabrication, and in-sodium testing of prototypical LMFBR plant-size flexible pipe joints which meet all ASME rule requirements. The satisfactory completion of these developmental goals will result in an approved flexible pipe joint design for the LMFBR. Progress is summarized in the following efforts undertaken during 1977 to accomplish these goals: (1) code case support, (2) engineering and design, (3) material development, (4) testing, and (5) manufacturing development

Study of structural attachments of a pool type LMFBR vessel through seismic analysis of a simplified three dimensional finite element model

International Nuclear Information System (INIS)

Ahmed, H.; Ma, D.

1979-01-01

A simplified three dimensional finite element model of a pool type LMFBR in conjunction with the computer program ANSYS is developed and scoping results of seismic analysis are produced. Through this study various structural attachments of a pool type LMFBR like the reactor vessel skirt support, the pump support and reactor shell-support structure interfaces are studied. This study also provides some useful results on equivalent viscous damping approach and some improvements to the treatment of equivalent viscous damping are recommended. This study also sets forth pertinent guidelines for detailed three dimensional finite element seismic analysis of pool type LMFBR

Specialists' meeting on maintenance and repair of LMFBR steam generators. Summary report

International Nuclear Information System (INIS)

2002-01-01

The purpose of the meeting was to review and discuss the experience accumulated in various countries on the general design philosophy of LMFBR steam generators from the view point of maintenance and repair, in-service inspection of steam generator tube bundles, identification and inspection of failed tubes and the cleaning and repairing of failed steam generators. The following main topic areas were discussed by participants: National review presentations on maintenance and repair of LMFBR steam generators - design philosophy for maintenance and repair; Research and Development work on maintenance and repair; Experience on steam generator maintenance and repair. During the meeting papers were presented by the participants on behalf of their countries and organizations. A final discussion session was held and summaries, general conclusions and recommendations were approved by consensus

Heterogeneous NiCo2O4@polypyrrole core/sheath nanowire arrays on Ni foam for high performance supercapacitors

Science.gov (United States)

Hu, Jing; Li, Minchan; Lv, Fucong; Yang, Mingyang; Tao, Pengpeng; Tang, Yougen; Liu, Hongtao; Lu, Zhouguang

2015-10-01

A novel heterogeneous NiCo2O4@PPy core/sheath nanowire arrays are directly grown on Ni foam involving three facile steps, hydrothermal synthesis and calcination of NiCo2O4 nanowire arrays and subsequent in-situ oxidative polymerization of polypyrrole (PPy). When investigated as binder- and conductive additive-free electrodes for supercapacitors (SCs) in 6 M KOH, the NiCo2O4@PPy core/sheath nanowire arrays exhibit high areal capacitance of 3.49 F cm-2 at a discharge current density of 5 mA cm-2, which is almost 1.5 times as much as the pristine NiCo2O4 (2.30 F cm-2). More importantly, it can remain 3.31 F cm-2 (94.8% retention) after 5000 cycles. The as-obtained electrode also displays excellent rate capability, whose areal capacitance can still remain 2.79 F cm-2 while the discharge current density is increased to 50 mA cm-2. The remarkable electrochemical performance is mainly attributed to the unique heterogeneous core/sheath nanowire-array architectures.

Cover-gas seals: 11-LMFBR seal-test program

International Nuclear Information System (INIS)

Steele, O.P. III; Horton, P.H.

1977-01-01

The objective of the Cover Gas Seal Material Development Program is to perform the engineering development required to provide reliable seals for LMFBR application. Specific objectives are to verify the performance of commercial solid cross-section and inflatable seals under reactor environments including radiation, to develop advanced materials and configurations capable of achieving significant improvement in radioactive gas containment and seal temperature capabilities, and to optimize seal geometry for maximum reliability and minimal gas permeation

Development of acidic processes for decontaminating LMFBR components

Energy Technology Data Exchange (ETDEWEB)

Hill, E F [Rockwell International, Atomics International Division, Canoga Park (United States); Colburn, R P; Lutton, J M; Maffei, H P [Hanford Engineering Development Laboratory, Richland (United States)

1978-08-01

The objective of the DOE decontamination program is to develop a well characterized chemical decontamination process for application to LMFBR primary system components that subsequently permits contact maintenance and allows requalification of the components for reuse in reactors. The paper describes the subtasks of deposit characterization, development of requalification and process acceptance criteria, development of process evaluation techniques and studies which led to a new acidic process for decontaminating 304 stainless steel hot leg components.

Analytical work on local faults in LMFBR subassembly

International Nuclear Information System (INIS)

Yoshikawa, H.; Miyaguchi, K.; Hirata, N.; Kasahara, F.

1979-01-01

Analytical codes have been developed for evaluating various severe but highly unlikely events of local faults in the LMFBR subassembly (S/A). These include: (1) local flow blockage, (2) two-phase thermohydraulics under fission gas release, and (3) inter-S/A failure propagation. A simple inter-S/A thermal failure propagation analysis code, FUMES, is described that allows an easy parametric study of propagation potential of fuel fog in a S/A. 7 refs

Route survey for LMFBR spent fuel transportation analysis

International Nuclear Information System (INIS)

Foley, J.T.

1977-05-01

Descriptions are given of surveys that were made along segments of interstate highways to obtain information on objects near the right-of-ways and on highway features that constitute hazards in the event of transportation accidents. Data collected during the surveys are summarized. The work was done in support of the LMFBR Hazards Analysis which was being performed for the Division of Reactor Development and Demonstration of the U.S. Energy Research and Development Administration

Development of acidic processes for decontaminating LMFBR components

International Nuclear Information System (INIS)

Hill, E.F.; Colburn, R.P.; Lutton, J.M.; Maffei, H.P.

1978-01-01

The objective of the DOE decontamination program is to develop a well characterized chemical decontamination process for application to LMFBR primary system components that subsequently permits contact maintenance and allows requalification of the components for reuse in reactors. The paper describes the subtasks of deposit characterization, development of requalification and process acceptance criteria, development of process evaluation techniques and studies which led to a new acidic process for decontaminating 304 stainless steel hot leg components

Computation system for nuclear reactor core analysis. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Vondy, D.R.; Fowler, T.B.; Cunningham, G.W.; Petrie, L.M.

1977-04-01

This report documents a system which contains computer codes as modules developed to evaluate nuclear reactor core performance. The diffusion theory approximation to neutron transport may be applied with the VENTURE code treating up to three dimensions. The effect of exposure may be determined with the BURNER code, allowing depletion calculations to be made. The features and requirements of the system are discussed and aspects common to the computational modules, but the latter are documented elsewhere. User input data requirements, data file management, control, and the modules which perform general functions are described. Continuing development and implementation effort is enhancing the analysis capability available locally and to other installations from remote terminals.

LMFBR thermal-striping evaluation

International Nuclear Information System (INIS)

Brunings, J.E.

1982-10-01

Thermal striping is defined as the fluctuating temperature field that is imposed on a structure when fluid streams at different temperatures mix in the vicinity of the structure surface. Because of the uncertainty in structural damage in LMFBR structures subject to thermal striping, EPRI has funded an effort for the Rockwell International Energy Systems Group to evaluate this problem. This interim report presents the following information: (1) a Thermal Striping Program Plan which identifies areas of analytic and experimental needs and presents a program of specific tasks to define damage experienced by ordinary materials of construction and to evaluate conservatism in the existing approach; (2) a description of the Thermal Striping Test Facility and its operation; and (3) results from the preliminary phase of testing to characterize the fluid environment to be applied in subsequent thermal striping damage experiments

Comparative analysis of LMFBR licensing in the United States and other countries - notably France. Executive summary

International Nuclear Information System (INIS)

Golay, M.W.; Castillo, M.

1981-01-01

The safety-related design aspects and licensing experiences of LMFBR projects in other democratic countries have been studied and contrasted to those in the United States in order to understand the importance of different approaches to safety, and also to understand better the system of the United States. The regulatory systems and LMFBR programs of France and the United States are contrasted in detail, and that of West Germany is also studied. The programs of Japan and the United Kingdom receive considerably less attention, and that of the Soviet Union is ignored

Analytical approach for confirming the achievement of LMFBR reliability goals

International Nuclear Information System (INIS)

Ingram, G.E.; Elerath, J.G.; Wood, A.P.

1981-01-01

The approach, recommended by GE-ARSD, for confirming the achievement of LMFBR reliability goals relies upon a comprehensive understanding of the physical and operational characteristics of the system and the environments to which the system will be subjected during its operational life. This kind of understanding is required for an approach based on system hardware testing or analyses, as recommended in this report. However, for a system as complex and expensive as the LMFBR, an approach which relies primarily on system hardware testing would be prohibitive both in cost and time to obtain the required system reliability test information. By using an analytical approach, results of tests (reliability and functional) at a low level within the specific system of interest, as well as results from other similar systems can be used to form the data base for confirming the achievement of the system reliability goals. This data, along with information relating to the design characteristics and operating environments of the specific system, will be used in the assessment of the system's reliability

A new approach to the design of LMFBR liners

International Nuclear Information System (INIS)

Polentz, L.M.

1980-01-01

An advance in the state-of-the-art of LMFBR liners which permits notable savings in construction costs without any sacrifice of safety is described. The application of the new design concept to the rework of the upper reactor vault liner of the FFTF is discussed. Factors which affect the application of the new design approach to other LMFBRs are delineated and discussed. (author)

The Influence of Heat Flux Boundary Heterogeneity on Heat Transport in Earth's Core

Science.gov (United States)

Davies, C. J.; Mound, J. E.

2017-12-01

Rotating convection in planetary systems can be subjected to large lateral variations in heat flux from above; for example, due to the interaction between the metallic cores of terrestrial planets and their overlying silicate mantles. The boundary anomalies can significantly reorganise the pattern of convection and influence global diagnostics such as the Nusselt number. We have conducted a suite of numerical simulations of rotating convection in a spherical shell geometry comparing convection with homogeneous boundary conditions to that with two patterns of heat flux variation at the outer boundary: one hemispheric pattern, and one derived from seismic tomographic imaging of Earth's lower mantle. We consider Ekman numbers down to 10-6 and flux-based Rayleigh numbers up to 800 times critical. The heterogeneous boundary conditions tend to increase the Nusselt number relative to the equivalent homogeneous case by altering both the flow and temperature fields, particularly near the top of the convecting region. The enhancement in Nusselt number tends to increase as the amplitude and wavelength of the boundary heterogeneity is increased and as the system becomes more supercritical. In our suite of models, the increase in Nusselt number can be as large as 25%. The slope of the Nusselt-Rayleigh scaling also changes when boundary heterogeneity is included, which has implications when extrapolating to planetary conditions. Additionally, regions of effective thermal stratification can develop when strongly heterogeneous heat flux conditions are applied at the outer boundary.

Benchmark calculation programme concerning typical LMFBR structures

International Nuclear Information System (INIS)

Donea, J.; Ferrari, G.; Grossetie, J.C.; Terzaghi, A.

1982-01-01

This programme, which is part of a comprehensive activity aimed at resolving difficulties encountered in using design procedures based on ASME Code Case N-47, should allow to get confidence in computer codes which are supposed to provide a realistic prediction of the LMFBR component behaviour. The calculations started on static analysis of typical structures made of non linear materials stressed by cyclic loads. The fluid structure interaction analysis is also being considered. Reasons and details of the different benchmark calculations are described, results obtained are commented and future computational exercise indicated

Thermal analysis methods for LMFBR wire wrapped bundles

International Nuclear Information System (INIS)

Todreas, N.E.

1976-11-01

A note is presented which was written to stimulate an awareness and discussion of the fundamental differences in the formulation of certain existing analysis codes for LMFBR wire wrap bundles. The contention of the note is that for those array types where data exists (one wire per pin, equal start angles), the ENERGY method results for coolant temperature under forced convection conditions provide benchmarks of reliability equal to the results of codes COBRA and TH1-3D

Axial migratin of cesium in LMFBR fuel pins

International Nuclear Information System (INIS)

Karnesky, R.A.; Bridges, A.E.; Jost, J.W.

1981-11-01

A correlated model for quantitatively predicting the behavior of cesium in LMFBR fuel pins has been developed. This correlation was shown to be in good agreement with experimental data. It has been used to predict the behavior of cesium in the FFTF driver fuel and as the result of this analysis it has been shown that the accumulation of cesium in the insulator pellets at the ends of the fuel column will not be life limiting

Biological behavior of mixed LMFBR-fuel-sodium aerosols

International Nuclear Information System (INIS)

Mahlum, D.D.; Hackett, P.L.; Hess, J.O.; Allen, M.D.

1979-01-01

Immediately after exposure of rats to mixed aerosols of sodium-LMFBR fuel, about 80 to 90% of the body burden of 239 Pu is in the gastrointestinal tract; 1.5 to 4% is in the lungs. With fuel-only aerosols, less of the body burden was in the GI tract and more in the lung and the head. Blood and urine values suggest an increased absorption of 239 Pu from sodium-fuel than from fuel-only aerosols

Technical considerations relative to removal of sodium from LMFBR components

Energy Technology Data Exchange (ETDEWEB)

McDonald, J S; Asquith, J G

1975-07-01

Reviewed in this paper are technical considerations which are of importance in choosing between an alcohol process and a moist nitrogen process for the removal of sodium from LMFBR components. Results observed in laboratory tests and in the cleaning of large scale components (e.g. a 28 MWt Modular Steam Generator Test Unit) are presented and discussed. (author)

32-core Dense SDM Unidirectional Transmission of PDM-16QAM Signals Over 1600 km Using Crosstalk-managed Single-mode Heterogeneous Multicore Transmission Line

DEFF Research Database (Denmark)

Mizuno, Takayuki; Shibahara, K.; Ono, Hirotaka

2016-01-01

We demonstrate 32-core dense space-division multiplexed (DSDM) unidirectional transmission of PDM-16QAM 20-WDM signals over 1644.8 km employing a low-crosstalk single-mode heterogeneous 32-core fiber in a partial recirculating-loop system....

LARA: Expert system for acoustic localization of robot in a LMFBR

International Nuclear Information System (INIS)

Lhuillier, C.; Malvache, P.

1986-12-01

The expert system LARA (Acoustic Localization of Autonomic Robot) has been developed to show the interest of introducing artificial intelligency for fine automatic positioning of refuelling machine in a LMFBR reactor. LARA which is equipped with an acoustic detector gives rapidly a good positioning on the fuel [fr

LMFBR subassembly response to simulated local pressure loadings

International Nuclear Information System (INIS)

Marciniak, T.J.; Ash, J.E.; Marchertas, A.H.; Cagliostro, D.J.

1976-01-01

The structural response of liquid metal fast breeder reactor (LMFBR) subassemblies to local accidental events is of interest in assessing the safety of such systems. Problems to be resolved include failure propagation modes from pin to pin and from subassembly to subassembly. Factors which must be considered include: (a) the geometry of the structure, (b) uncertainty of the pressure-energy source, (c) uncertainty of materials properties under reactor operating conditions, and (d) the difficulty in performing in-pile or out-of-pile experiments which would simulate the above conditions. The main effort in evaluating the subassembly response has been centered around the development of appropriate analyses based on the finite element technique. Analysis has been extended to include not only the subassembly duct structure itself, but also the fluid environment, both within subassemblies and between them. These models and codes have been devised to cover a wide range of accident loading conditions, and can treat various materials as their properties become known. The effort described here is centered mainly around an experimental effort aimed at verfying, modifying or extending the models used in treating subassembly damage propagation. To verify the finite element codes under development, a series of out-of-pile room temperature experiments has been performed on LMFBR-type subassembly ducts under various loading conditions. (Auth.)

Research on SEU hardening of heterogeneous Dual-Core SoC

Science.gov (United States)

Huang, Kun; Hu, Keliu; Deng, Jun; Zhang, Tao

2017-08-01

The implementation of Single-Event Upsets (SEU) hardening has various schemes. However, some of them require a lot of human, material and financial resources. This paper proposes an easy scheme on SEU hardening for Heterogeneous Dual-core SoC (HD SoC) which contains three techniques. First, the automatic Triple Modular Redundancy (TMR) technique is adopted to harden the register heaps of the processor and the instruction-fetching module. Second, Hamming codes are used to harden the random access memory (RAM). Last, a software signature technique is applied to check the programs which are running on CPU. The scheme need not to consume additional resources, and has little influence on the performance of CPU. These technologies are very mature, easy to implement and needs low cost. According to the simulation result, the scheme can satisfy the basic demand of SEU-hardening.

Influence of fission product transport on delayed neutron precursors and decay heat sources in LMFBR accidents

International Nuclear Information System (INIS)

Apperson, C.E. Jr.

1981-01-01

A method is presented for studying the influence of fission product transpot on delayed neutron precursors and decay heat sources during Liquid Metal Fast Breeder Reactor (LMFBR) unprotected accidents. The model represents the LMFBR core as a closed homogeneous cell. Thermodynamic phase equilibrium theory is used to predict fission product mobility. Reactor kinetics behavior is analyzed by an extension of point kinetics theory. Group dependent delayed neutron precursor and decay heat source retention factors, which represent the fraction of each group retained in the fuel, are developed to link the kinetics and thermodynamics analysis. Application of the method to a highly simplified model of an unprotected loss-of-flow accident shows a time delay on the order of 10 ms is introduced in the predisassembly power history if fission product motion is considered when compared to the traditional transient solution. The post-transient influence of fission product transport calculated by the present model is a 24 percent reduction in the decay heat level in the fuel material which is similar to traditional approximations. Isotopes of the noble gases, Kr and Xe, and the elements I and Br are shown to be very mobile and are responsible for a major part of the observed effects. Isotopes of the elements Cs, Se, Rb, and Te were found to be moderately mobile and contribute to a lesser extent to the observed phenomena. These results obtained from the application of the described model confirm the initial hypothesis that sufficient fission product transport can occur to influence a transient. For these reasons, it is concluded that extension of this model into a multi-cell transient analysis code is warranted

Impact of LMFBR operating experience on PFBR design

International Nuclear Information System (INIS)

Bhoje, S.B.; Chetal, S.C.; Chellapandi, P.; Govindarajan, S.; Lee, S.M.; Kameswara Rao, A.S.L.; Prabhakar, R.; Raghupathy, S.; Sodhi, B.S.; Sundaramoorthy, T.R.; Vaidyanathan, G.

2000-01-01

PFBR is a 500 MWe, sodium cooled, pool type, fast breeder reactor currently under detailed design. It is essential to reduce the capital cost of PFBR in order to make it competitive with thermal reactors. Operating experience of LMFBRs provides a vital input towards simplification of the design, improving its reliability, enhancing safety and achieving overall cost reduction. This paper includes a summary of LMFBR operating experience and details the design features of PFBR as influenced by operating experience of LMFBRs. (author)

Feasibility study for adapting ITREC plant to reprocessing LMFBR fuels

International Nuclear Information System (INIS)

Moccia, A.; Rolandi, G.

1976-05-01

The report evaluates the feasibility of adapting ITREC plant to the reprocessing LMFBR fuels, with the double purpose of: 1) recovering valuable Pu contained in these fuels and recycling it to the fabrication plant; 2) trying, on a pilot scale, the chemical process technology to be applied in a future industrial plant for reprocessing the fuel elements discharged from fast breeder power reactors

Small leak shutdown, location, and behavior in LMFBR steam generators

International Nuclear Information System (INIS)

Sandusky, D.W.

1976-01-01

The paper summarizes an experimental study of small leaks tested under LMFBR steam generator conditions. Defected tubes were exposed to flowing sodium and steam. The observed behavior of the defected tubes is reported along with test results of shutdown methods. Leak location methods were investigated. Methods were identified to open plugged defects for helium leak testing and detect plugged leaks by nondestructive testing

A survey of the French creep-fatigue design rules for LMFBR

International Nuclear Information System (INIS)

Tribout, J.; Cordier, G.; Moulin, D.

1987-01-01

The paper provides a survey of the creep-fatigue design rules for the LMFBR in France. These rules are the ones currently implemented in French component manufacturing. The background of each item is discussed and the trends for improvements currently investigated are described. The creep-fatigue rules apply to elastic analysis only. (orig.)

The water vapor nitrogen process for removing sodium from LMFBR components

Energy Technology Data Exchange (ETDEWEB)

Crippen, M D; Funk, C W; Lutton, J M [Hanford Engineering Development Laboratory, Richland (United States)

1978-08-01

Application and operation of the Water Vapor-Nitrogen Process for removing sodium from LMFBR components is reviewed. Emphasis is placed on recent efforts to verify the technological bases of the process, to refine the values of process parameters and to ensure the utility of the process for cleaning and requalifying components. (author)

A probabilistic design method for LMFBR fuel rods

International Nuclear Information System (INIS)

Peck, S.O.; Lovejoy, W.S.

1977-01-01

Fuel rod performance analyses for design purposes are dependent upon material properties, dimensions, and loads that are statistical in nature. Conventional design practice accounts for the uncertainties in relevant parameters by designing to a 'safety factor', set so as to assure safe operation. Arbitrary assignment of these safety factors, based upon a number of 'worst case' assumptions, may result in costly over-design. Probabilistic design methods provide a systematic way to reflect the uncertainties in design parameters. PECS-III is a computer code which employs Monte Carlo techniques to generate the probability density and distribution functions for time-to-failure and cumulative damage for sealed plenum LMFBR fuel rods on a single rod or whole core basis. In Monte Carlo analyses, a deterministic model (that maps single-valued inputs into single-valued outputs) is coupled to a statistical 'driver'. Uncertainties in the input are reflected by assigning probability densities to the input parameters. Dependent input variables are considered multivariate normal. Independent input variables may be arbitrarily distributed. Sample values are drawn from these input densities, and a complete analysis is done by the deterministic model to generate a sample point in the output distribution. This process is repeated many times, and the number of times each output value occurs is accumulated. The probability that some measure of rod performance will fall within given limits is estimated by the relative frequency with which the Monte Carlo samples fall within tho

Retention of gaseous fission products in reprocessing LMFBR fuels

International Nuclear Information System (INIS)

Burch, W.D.; Yarbro, O.O.; Groenier, W.S.; Stephenson, M.J.

1976-05-01

The report is devoted to status of the development programme at the Oak Ridge National Laboratory on methods for retaining iodine-131 and 129, Krypton-85, Tritium and Carbon-14 in reprocessing LMFBR fuels. The Iodox process, Fluorocarbon absorption process and Voloxidation process are described for retention of iodine, Krypton-85 and Tritium, respectively. Flowsheets for the different processes are given and results of experimental runs in small engineering-scale equipment are reported

Thermal interactions of a molten core debris pool with surrounding structural materials

International Nuclear Information System (INIS)

Baker, L. Jr.; Cheung, F.B.; Farhadieh, R.; Stein, R.P.; Gabor, J.D.; Bingle, J.D.

1979-01-01

Analytical and experimental results on individual aspects of the overall problem of the interaction of a large mass of LMFBR core debris with concrete or other materials are reviewed. Results of recent heat transfer experiments with molten UO 2 have indicated the importance of internal thermal radiation and methods to take account of this are developed. Effects of gas release and density difference are considered. The GROWS-2 Code is used to illustrate the effects of various assumptions

Problems of heat transfer within the containing vessel of high performance LMFBR spent fuel shipping casks

International Nuclear Information System (INIS)

Pope, R.B.; Gartling, D.K.; Schimmel, W.P. Jr.; Larson, D.W.

1976-01-01

A preliminary assessment of heat transfer problems internal to a LMFBR spent fuel shipping cask is reported. The assessment is based upon previous results obtained in full-scale, electrically heated mockups of an LMFBR assembly located in a containing pipe, and also upon analytical and empirical studies presented in this paper. It is shown that a liquid coolant will be required to adequately distribute the decay heat of short-cooled assemblies from the fuel region to the containing cask structure. Liquid sodium apparently provides the best heat transfer, and sufficient data are available to adequately model the heat transfer processes involved. Dowtherm A is the most efficient organic evaluated to date and presented in the open literature. Since the organic materials have high Prandtl and usually high Rayleigh numbers, natural convection is the predominant mode of heat transfer. It is shown that a more comprehensive understanding of the convective processes will be required before heat transfer with an organic coolant can be adequately modeled. However, in view of systems considerations, Dowtherm A should be further considered as an alternative to sodium for use as a LMFBR spent fuel shipping cask coolant

Evaluation of air cleaning system concepts for emergency use in LMFBR plants

International Nuclear Information System (INIS)

Hilliard, R.K.; McCormack, J.D.; Postma, A.K.

1976-12-01

Nineteen different air cleaning concepts are arranged into twenty-four systems and evaluated for use as accident mitigating systems in LMFBR plants. Both single, low-leakage containment plants and once-through operation applicable to containment/confinement plants are considered. Plant characteristics affecting air cleaning requirements are defined for 1000 MW(e) plants and a sodium and radiological release term is postulated. The accident conditions under which the emergency air cleaning system (EACS) must function is established by use of SOFIRE-II and HAA-3B computer codes. Criteria are developed for evaluating the various systems and for assigning comparative ratings. The numerical ratings are combined with information on cost and development potential to arrive at recommendations for the most promising systems. The conclusion is made that reliable and effective systems are feasible for use as engineered safety features for LMFBR plants, but that development effort is required for all the air cleaning concepts evaluated

Overview of current activities relevant to structural analysis on LMFBR in Japan

International Nuclear Information System (INIS)

Ichimiya, Masakazu

1983-01-01

This paper presents the structural analysis activities on LMFBR in Japan. The structural analysis activities on LMFBR in Japan have been made mainly toward the validation of the rules of high temperature structural design guide which is to be used for the design of Class 1 components for elevated temperature service of the prototype fast breeder reactor, Monju. Main features of these analyses are as follows. (1) Since the design by elastic analysis is intended in the high temperature structural design guide of Monju, a large progress has been made in the bounding technique for high temperature inelastic behaviors, particularly the elastic follow-up. (2) There has been a progress in the clarification of the creep behavior in order to evaluate creep damage adequately. (3) Analysis techniques and design rules for piping have been developed with considerable emphasis. In addition, buckling analyses were performed considering the thin structures with low internal pressure in Monju components. Further test and analysis were made on ratcheting. (author)

Microprocessor-based integrated LMFBR core surveillance. Pt. 2

International Nuclear Information System (INIS)

Elies, V.

1985-12-01

This report is the result of the KfK part of a joint study of KfK and INTERATOM. The aim of this study is to explore the advantages of microprocessors and microelectronics for a more sophisticated core surveillance, which is based on the integration of separate surveillance techniques. After a description of the experimental results gained with the different surveillance techniques so far, it is shown which kinds of correlation can be done using the evaluation results obtained from the single surveillance systems. The main part of this report contains the systems analysis of a microcomputer-based system integrating different surveillance methods. After an analysis of the hardware requirements a hardware structure for the integrated system is proposed. The software structure is then described for the subsystem performing the different surveillance algorithms as well as for the system which does the correlation thus deriving additional information from the single results. (orig.) [de

The RCC-MR design code for LMFBR components. A useful basis for fusion reactor design tools development

International Nuclear Information System (INIS)

Acker, D.; Chevereau, G.

1986-01-01

LMFBR and fusion reactors exhibit common features with regard to structural materials, temperature service level, loading types. So, design and construction rules used in France for LMFBR, that is to say RCC-MR Code, can constitute a good basis for fusion reactors design. Some original aspects of RCC-MR design rules are described, relating to unsignificant creep, ratchetting effect, fatigue and creep damage limits, creep damage evaluation, fatigue damage evaluation, buckling. The main originality of RCC-MR consists to propose comprehensive simplified rules based on elastic calculations and extended from classical cold temperatures to the elevated temperature domain. (author)

LMFBR models for the ORIGEN2 computer code

International Nuclear Information System (INIS)

Croff, A.G.; McAdoo, J.W.; Bjerke, M.A.

1981-10-01

Reactor physics calculations have led to the development of nine liquid-metal fast breeder reactor (LMFBR) models for the ORIGEN2 computer code. Four of the models are based on the U-Pu fuel cycle, two are based on the Th-U-Pu fuel cycle, and three are based on the Th- 238 U fuel cycle. The reactor models are based on cross sections taken directly from the reactor physics codes. Descriptions of the reactor models as well as values for the ORIGEN2 flux parameters THERM, RES, and FAST are given

Welding development for LMFBR applications

International Nuclear Information System (INIS)

Slaughter, G.M.; Edmonds, D.P.; Goodwin, G.M.; King, J.F.; Moorhead, A.J.

1976-01-01

High-quality welds with suitable properties for long-time elevated-temperature nuclear service are among the most critical needs in today's welding technology. Safe, reliable, and economic generation of future power depends on welded construction in systems such as Liquid Metal Fast Breeder Reactors (LMFBRs). Rapid thermal transients in LMFBR systems at coolant temperatures around 590 to 650 0 C (1000 to 1200 0 F) could cause creep and creep-fatigue damage that is not encountered in lower temperature reactor systems. The undesirable consequences of interaction between the two working fluids - sodium and steam - in the steam generators are also of major concern. Thus sound welds that have excellent reliability over a 30-year service life are essential. Several programs are actively underway at ORNL to satisfy this critical need and selected portions of three of these programs are discussed briefly

Analysis of transient thermal response in the outlet plenum of an LMFBR

International Nuclear Information System (INIS)

Yang, J.W.

1976-05-01

A two-zone mixing model based on the lumped-parameter approach was developed for the analysis of transient thermal response in the upper outlet plenum of an LMFBR. The one-dimensional turbulent jet flow equations were solved to determine the maximum penetration of the core flow. The maximum penetration is used as the criterion for dividing the sodium region into two mixing zones. The lumped-parameter model considers the transient sodium temperature affected by the thermal expansion of sodium, heat transfer with cover gas, heat capacity of different sections of metal and the addition of bypass flow into the plenum. Numerical calculations were performed for two cases. The first case corresponds to a normal scram followed by flow coast-down. The second case represents the double-ended pipe rupture at the inlet of cold leg followed by reactor scram. The results indicate that effects of flow stratification, chimney height, metal heat capacity and bypass flow are important for transient sodium temperature calculation. Thermal expansion of sodium and heat transfer with the cover gas does not play any significant role on sodium temperature. This two-zone mixing model will be a part of the thermohydraulic transient code SSC

Calculation of pressure drop and flow redistribution in the LMFBR core

International Nuclear Information System (INIS)

Morgado, O.J.

1984-01-01

The flow redistribution through fuel assemblies of LMFBRs: for the correct calculation of mass flow rates and pressure drop, are studied. Using a quasi-static formulation of conservation equations of mass and energy, a computer program was developed to simulate any arbitrary number of flow channels, operating at different linear power levels. Therefore f flow channels, operating at different linear power levels. Therefore, it was possible to perform thermal transient calculations for the Clinch River reactor core. The results of the calculations agree with the data found in the literature and supply accurate information about flow redistribution, average temperature, and pressure drop in the core, when the reactor is operated at conditions from the designed flow conditions, as is always the case in a load changing operation, or during transients. (Autor) [pt

Shielding design method for LMFBR validation on the Phenix factor

International Nuclear Information System (INIS)

Cabrillat, J.C.; Crouzet, J.; Misrakis, J.; Salvatores, M.; Rado, V.; Palmiotti, G.

1983-05-01

Shielding design methods, developed at CEA for shielding calculations find a global validation by the means of Phenix power reactor (250 MWe) measurements. Particularly, the secondary sodium activation of pool type LMFBR such as Super Phenix (1200 MWe) which is subject to strict safety limitation is well calculated by the adapted scheme, i.e. a two dimension transport calculation of shielding coupled to a Monte-Carlo calculation of secondary sodium activation

LMFBR safety program. Annual technical progress report. Government fiscal year, 1977

International Nuclear Information System (INIS)

1977-01-01

Information is presented concerning the development of the SOMIX-1 computer code for sodium drop burning analysis; experimental analysis of burning sodium drops; aerosol leakage from containment buildings; high-temperature-concentration aerosols; aerosol source term from vaporized fuel; properties of high-temperature fuel mixtures; and development of the COMRADEX computer code for analysis of radiological doses in the environment from LMFBR accidents

Structural analysis for elevated temperature design of the LMFBR

International Nuclear Information System (INIS)

Griffin, D.S.

1976-02-01

In the structural design of LMFBR components for elevated temperature service it is necessary to take account of the time-dependent, creep behavior of materials. The accommodation of creep to assure design reliability has required (1) development of new design limits and criteria, (2) development of more detailed representations of material behavior, and (3) application of the most advanced analysis techniques. These developments are summarized and examples are given to illustrate the current state of technology in elevated temperature design

The RCC-MR design code for LMFBR components. A useful basic for fusion reactor design tools development

International Nuclear Information System (INIS)

Acker, D.; Chevereau, G.

1985-11-01

LMFBR and fusion reactors exhibit common features with regard to structural materials (Stainless steels), temperature service level (550-600 0 C), loading types. So, design and construction rules used in France for LMFBR, that is to say RCC-MR Code, can constitute a good basis for fusion reactors design. Some original aspects of RCC-MR design rules are described, relating to unsignificant creep, ratchetting effect, fatigue and creep damage limits, creep damage evaluation, fatigue damage evaluation, buckling. The main originality of RCC-MR consists to propose comprehensive simplified rules based on elastic calculations and extended from classical cold temperatures to the elevated temperature domain

Status of the LMFBR development

Energy Technology Data Exchange (ETDEWEB)

Taylor, J J

1975-01-01

The development of any new power generation system which can make a major contribution to our energy needs is a multi-faceted task involving the utilization of major human and material resources. The LMFBR development, which has the potential for supplying abundant energy for generations, is therefore a large, multi-faceted program. This summary will cover (1) the need for the liquid metal fast breeder reactor, (2) an overall perspective of its development throughout the world, (3) a brief look at the in-depth technological development program in the United States, (4) a description and status of the two major projects now under way in the program, the Fast Flux Test Facility and the Clinch River Breeder Reactor Plant, and (5) a review of the plans for continued development to achieve a reliable, safe and economic power generation system for practical commercial use on the utility networks of the country.

LMFBR plant parameters 1991

International Nuclear Information System (INIS)

1991-03-01

The document has been prepared on the basis of information provided by the members of the IAEA International Working Group on Fast Reactors (IWGFR). It contains updated parameters of 27 experimental, prototype and commercial size liquid metal fast breeder reactors (LMFBRs). Most of the reactors are currently in operation, under construction or in an advanced planning stage. Parameters of the Clinch River Breeder Reactor (USA), PEC (Italy), RAPSODIE (France), DFR (UK) and EFFBR (USA) are included in the report because of their important role in the development of LMFBR technology from first LMFBRs to the prototype size fast reactors. Two more reactors appeared in the list: European Fast Reactor (EFR) and PRISM (USA). Parameters of these reactors included in this publication are based on the data from the papers presented at the 23rd Annual Meeting of the IWGFR. All in all more than four hundred corrections and additions have been made to update the document. The report is intended for specialists and institutions in industrialized and developing countries who are responsible for the design and operation of liquid metal fast breeder reactors

Seismic analysis of a large LMFBR with fluid-structure interactions

International Nuclear Information System (INIS)

Ma, D.C.

1985-01-01

The seismic analysis of a large LMFBR with many internal components and structures is presented. Both vertical and horizontal seismic excitations are considered. The important hydrodynamic phenomena such as fluid-structure interaction, sloshing, fluid coupling and fluid inertia effects are included in the analysis. The results of this study are discussed in detail. Information which is useful to the design of future reactions under seismic conditions is also given. 4 refs., 12 figs

Maintenance and repair of LMFBR steam generators: specialists` meeting, O-Arai Engineering Center, Japan, 4-8 June 1984. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-07-01

The Specialists` Meeting on "Maintenance and Repair of LMFBR Steam Generators" was held in Oarai, Japan, from 4-8 June 1984. The meeting was sponsored by the International Atomic Energy Agency on the recommendation of the IAEA International Working Group on Fast Reactors and was hosted by the Power Reactor and Nuclear Fuel Development Corporation of Japan. The purpose of the meeting was to review and discuss the experience accumulated in various countries on the general design philosophy of LMFBR steam generators from the view point of maintenance and repair, in-service inspection of steam generator tube bundles, identification and inspection of failed tubes and the cleaning and repairing of failed steam generators. The following main topical areas were discussed by participants: national review presentations on maintenance and repair of LMFBR steam generators - design philosophy for maintenance and repair; research and development work on maintenance and repair; and experience on steam generator maintenance and repair.

Advances in methods of commercial FBR core characteristics analyses. Investigations of a treatment of the double-heterogeneity and a method to calculate homogenized control rod cross sections

Energy Technology Data Exchange (ETDEWEB)

Sugino, Kazuteru [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center; Iwai, Takehiko

1998-07-01

A standard data base for FBR core nuclear design is under development in order to improve the accuracy of FBR design calculation. As a part of the development, we investigated an improved treatment of double-heterogeneity and a method to calculate homogenized control rod cross sections in a commercial reactor geometry, for the betterment of the analytical accuracy of commercial FBR core characteristics. As an improvement in the treatment of double-heterogeneity, we derived a new method (the direct method) and compared both this and conventional methods with continuous energy Monte-Carlo calculations. In addition, we investigated the applicability of the reaction rate ratio preservation method as a advanced method to calculate homogenized control rod cross sections. The present studies gave the following information: (1) An improved treatment of double-heterogeneity: for criticality the conventional method showed good agreement with Monte-Carlo result within one sigma standard deviation; the direct method was consistent with conventional one. Preliminary evaluation of effects in core characteristics other than criticality showed that the effect of sodium void reactivity (coolant reactivity) due to the double-heterogeneity was large. (2) An advanced method to calculate homogenize control rod cross sections: for control rod worths the reaction rate ratio preservation method agreed with those produced by the calculations with the control rod heterogeneity included in the core geometry; in Monju control rod worth analysis, the present method overestimated control rod worths by 1 to 2% compared with the conventional method, but these differences were caused by more accurate model in the present method and it is considered that this method is more reliable than the conventional one. These two methods investigated in this study can be directly applied to core characteristics other than criticality or control rod worth. Thus it is concluded that these methods will

Simulation of heat and mass transfer processes in molten core debris-concrete systems. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Felde, D K

1979-01-01

The heat and mass transport phenomena taking place in volumetrically-heated fluids have become of interest in recent years due to their significance in assessments of fast reactor safety and post-accident heat removal (PAHR). Following a hypothetical core disruptive accident (HCDA), the core and reactor internals may melt down. The core debis melting through the reactor vessel and guard vessel may eventually contact the concrete of the reactor cell floor. The interaction of the core debris with the concrete as well as the melting of the debris pool into the concrete will significantly affect efforts to prevent breaching of the containment and the resultant release of radioactive effluents to the environment.

State of the art review of degradation processes in LMFBR materials. Volume II. Corrosion behavior

International Nuclear Information System (INIS)

Dillon, R.D.

1975-01-01

Degradation of materials exposed to Na in LMFBR service is reviewed. The degradation processes are discussed in sections on corrosion and mass transfer, erosion, wear and self welding, sodium--water reactions, and external corrosion. (JRD)

Comprehensive method of common-mode failure analysis for LMFBR safety systems

International Nuclear Information System (INIS)

Unione, A.J.; Ritzman, R.L.; Erdmann, R.C.

1976-01-01

A technique is demonstrated which allows the systematic treatment of common-mode failures of safety system performance. The technique uses log analysis in the form of fault and success trees to qualitatively assess the sources of common-mode failure and quantitatively estimate the contribution to the overall risk of system failure. The analysis is applied to the secondary control rod system of an early sized LMFBR

A survey of LMFBR cavitation technology in the U.S.A

International Nuclear Information System (INIS)

Cha, Y.S.; Huebotter, P.R.; Hopenfeld, J.

1976-01-01

Several experimental programmes of a basic and applied nature were established in the USA in order to develop guidelines to ensure design and operation of LMFBR hydraulic components free from cavitation and/or cavitation damage. As of March 1976, most of these experimental programs are still in progress. Each programme is briefly described. The available interium data are presented. References that are relevant are provided

Status of U.S. LMFBR programme

International Nuclear Information System (INIS)

Yevich, J.

1978-01-01

The determents of the decision for deterrence of commercial reprocessing and further demonstration of the plutonium breeder were based on two premises: time is needed to establish the programme for non-proliferating fuel cycle and there is a lessened sense of urgency for the USA to establish a commercial breeder in the near future. A strong, well funded base technology effort remains and will continue until institutional and technical solutions can be found to minimize or eliminate the proliferation risk. An LMFBR option will be maintained. The FFTF will be coming on line providing a powerful tool in breeder fuel and materials development and a baseline from which to scale up heat transfer systems and components. Sodium system hardware development and testing will continue to have high priority

Simple LMFBR axial-flow friction-factor correlation

International Nuclear Information System (INIS)

Chan, Y.N.; Todreas, N.E.

1981-09-01

Complicated LMFBR axial lead-length averaged friction factor correlations are reduced to an easy, ready-to-use function of bundle Reyonlds number for wire-wrapped bundles. The function together with the power curves to calculate the associated constants are incorporated in a computer pre-processor, EZFRIC. The constants required for the calculation of the subchannels and bundle friction factors are derived and correlated into power curves of geometrical parameters. A computer program, FRIC, which can alternatively be used to accurately calculate these constants is also included. The accuracte values of the constants and the corresponding values predicted by the power curves and percentage error of prediction are tabulated for a wide variety of geometries of interest

Whole core calculations of power reactors by Monte Carlo method

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Mori, Takamasa

1993-01-01

Whole core calculations have been performed for a commercial size PWR and a prototype LMFBR by using vectorized Monte Carlo codes. Geometries of cores were precisely represented in a pin by pin model. The calculated parameters were k eff , control rod worth, power distribution and so on. Both multigroup and continuous energy models were used and the accuracy of multigroup approximation was evaluated through the comparison of both results. One million neutron histories were tracked to considerably reduce variances. It was demonstrated that the high speed vectorized codes could calculate k eff , assembly power and some reactivity worths within practical computation time. For pin power and small reactivity worth calculations, the order of 10 million histories would be necessary. Required number of histories to achieve target design accuracy were estimated for those neutronic parameters. (orig.)

Sodium water reaction R and D for French LMFBR

International Nuclear Information System (INIS)

Cambillard, E.; Finck, P.; Lapicore, A.; Simeon, C.

1985-01-01

This paper presents the research and development which is underway for the French LMFBR steam generator safety study. The program comprises three major areas: (1) the analysis of realistic leaks, which includes the leak evolution and its consequences; (2) the response time of leak detection systems compared to leak propagation phenomena; and (3) the guillotine rupture (DBA) studies relative to source term evaluation by experimental/calculational approach and mechanical calculations. This program has provided information for the demonstrations of the steam generator safety in respect to a sodium-water reaction

Designing Domain-Specific Heterogeneous Architectures from Dataflow Programs

Directory of Open Access Journals (Sweden)

Süleyman Savas

2018-04-01

Full Text Available The last ten years have seen performance and power requirements pushing computer architectures using only a single core towards so-called manycore systems with hundreds of cores on a single chip. To further increase performance and energy efficiency, we are now seeing the development of heterogeneous architectures with specialized and accelerated cores. However, designing these heterogeneous systems is a challenging task due to their inherent complexity. We proposed an approach for designing domain-specific heterogeneous architectures based on instruction augmentation through the integration of hardware accelerators into simple cores. These hardware accelerators were determined based on their common use among applications within a certain domain.The objective was to generate heterogeneous architectures by integrating many of these accelerated cores and connecting them with a network-on-chip. The proposed approach aimed to ease the design of heterogeneous manycore architectures—and, consequently, exploration of the design space—by automating the design steps. To evaluate our approach, we enhanced our software tool chain with a tool that can generate accelerated cores from dataflow programs. This new tool chain was evaluated with the aid of two use cases: radar signal processing and mobile baseband processing. We could achieve an approximately 4 × improvement in performance, while executing complete applications on the augmented cores with a small impact (2.5–13% on area usage. The generated accelerators are competitive, achieving more than 90% of the performance of hand-written implementations.

Basic analysis and a comparison of the characteristics GCFRs and the LMFBR with the thorium cycle in one-group diffusion theory

International Nuclear Information System (INIS)

Sabundjian, G.; Ishiguro, Y.

1991-09-01

A preliminary study of neutronics of thorium cycle fast breeder reactor has been done using simplified reactor models and analyses methods with the aim of finding a type of breeder reactor suitable for an efficient utilization of thorium that is abundant in Brazil. Basic methods of cross section processing and reactor calculation are studied and applied to analyse breeding characteristics of GCFRs and LMFBRs. The GCFR is fueled with oxide pins and cooled with helium. The LMFBR is fueled with thin metallic pins to achieve high power densities. Neutronics characteristics are determined as functions of the average power density and the fuel volume fraction. Results show that a high power density and a high fuel volume fraction are desirable to achieve short doubling times, that the GCFR is inferior to the LMFBR in regard to the doubling time and that the LMFBR can achieve reactor doubling times ten years with an average power density of ∼ 600MW/m 3 and fuel volume fraction of 40%. (author)

LMFBR safety. 6. Review of current issues and bibliography of literature (1977)

International Nuclear Information System (INIS)

Buchanan, J.R.; Keilholtz, G.W.

1978-01-01

This report discusses the current status of liquid-metal fast breeder reactor (LMFBR) development. Selected bibliographic information on LMFBRs relative to the development and safety of the breeder reactor is presented for the year 1977. The bibliography consists of approximately 198 abstracts covering research and development, operating experience, and design practices. Keyword, author, and permuted-title indexes are included for completeness

Component mode synthesis methods applied to 3D heterogeneous core calculations, using the mixed dual finite element solver MINOS

Energy Technology Data Exchange (ETDEWEB)

Guerin, P.; Baudron, A. M.; Lautard, J. J. [Commissariat a l' Energie Atomique, DEN/DANS/DM2S/SERMA/LENR, CEA Saclay, 91191 Gif sur Yvette (France)

2006-07-01

This paper describes a new technique for determining the pin power in heterogeneous core calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions: in the first one (Component Mode Synthesis method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (Factorized Component Mode Synthesis method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well-fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher order angular approximations - particularly easily to a SPN approximation - the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with UOX and MOX assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

Component mode synthesis methods applied to 3D heterogeneous core calculations, using the mixed dual finite element solver MINOS

International Nuclear Information System (INIS)

Guerin, P.; Baudron, A. M.; Lautard, J. J.

2006-01-01

This paper describes a new technique for determining the pin power in heterogeneous core calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions: in the first one (Component Mode Synthesis method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (Factorized Component Mode Synthesis method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well-fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher order angular approximations - particularly easily to a SPN approximation - the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with UOX and MOX assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

Investigation on generalized Variational Nodal Methods for heterogeneous nodes

International Nuclear Information System (INIS)

Wang, Yongping; Wu, Hongchun; Li, Yunzhao; Cao, Liangzhi; Shen, Wei

2017-01-01

Highlights: • We developed two heterogeneous nodal methods based on the Variational Nodal Method. • Four problems were solved to evaluate the two heterogeneous nodal methods. • The function expansion method is good at treating continuous-changing heterogeneity. • The finite sub-element method is good at treating discontinuous-changing heterogeneity. - Abstract: The Variational Nodal Method (VNM) is generalized for heterogeneous nodes and applied to four kinds of problems including Molten Salt Reactor (MSR) core problem with continuous cross section profile, Pressurized Water Reactor (PWR) control rod cusping effect problem, PWR whole-core pin-by-pin problem, and heterogeneous PWR core problem without fuel-coolant homogenization in each pin cell. Two approaches have been investigated for the treatment of the nodal heterogeneity in this paper. To concentrate on spatial heterogeneity, diffusion approximation was adopted for the angular variable in neutron transport equation. To provide demonstrative numerical results, the codes in this paper were developed in slab geometry. The first method, named as function expansion (FE) method, expands nodal flux by orthogonal polynomials and the nodal cross sections are also expressed as spatial depended functions. The second path, named as finite sub-element (FS) method, takes advantage of the finite-element method by dividing each node into numbers of homogeneous sub-elements and expanding nodal flux into the combination of linear sub-element trial functions. Numerical tests have been carried out to evaluate the ability of the two nodal (coarse-mesh) heterogeneous VNMs by comparing with the fine-mesh homogeneous VNM. It has been demonstrated that both heterogeneous approaches can handle heterogeneous nodes. The FE method is good at continuous-changing heterogeneity as in the MSR core problem, while the FS method is good at discontinuous-changing heterogeneity such as the PWR pin-by-pin problem and heterogeneous PWR core

Nuclear welding, application for an LMFBR

International Nuclear Information System (INIS)

Patriarca, P.; Goodwin, G.M.

1975-01-01

Fabrication of an LMFBR system is discussed, with emphasis on areas where joint welding innovations have been introduced. Each major component of the system, including reactor vessel, intermediate heat exchanger, steam generator, and sodium-containment piping, is treated separately. Developmet of special filler metals to avoid the low elevated-temperature creep ductility obtained with conventional austenitic stainless steel weldments is reported. Bore-side welding of steam generator tube-to-tubesheet joints with and without filler metal is desirable to improve inspectability and eliminate the crevice inherent with face-side weld design, thus minimizing corrosion problems. Automated welding methods for sodium-containment piping are summarized which iminimize and control distortion and ensure welds of high integrity. Selection of materials for the various components is discussed for plants presently under construction, and materials predictions are made for future concepts. (U.S.)

Safety issues for LMFBR: important features drawn from the assessments of Superphenix

International Nuclear Information System (INIS)

Natta, M.

2002-01-01

Superphenix, which is built on the site of Creys-Malville, is still the biggest LMFBR plant that has been in operation. It is a pool type reactor, as Phenix and the RNR 1 500 and EFR projects. After the analysis of the preliminary safety (1974-1975), the construction was authorised by decree of the Prime Minister in 1977, the authorization for fuel loading and star-up to 3% was given by the minister of industry in July 1985 and full power was achieved in December 1986. The plant was operated until the end of December 1996, producing the equivalent of 320 EFPD, corresponding to half of the maximum barn-up of the first core. The plant was definitively stopped on the 20. of April 1998 by a decision of the French government. During this period of 25 years of licensing, construction and operation of Superphenix, others discussions and preliminary licensing procedures were started for new projects, mainly the RNR 1500 French project and the EFR European project. The operation of Superphenix was also marked by several incidents, which led to additional licensing procedures and important modifications. This period was also marked by an important work of research and development in the safety field, mostly related to the issues concerning hypothetical core disruptive accidents (HCDA) and sodium fires; further, this period was marked by the Three Mile Island accident in 1979 and the Chernobyl accident in 1986. The purpose of this paper is to present some items which were discussed during this period of 25 years and which should be of interest for future LMFBRs. In this presentation, we shall discuss the key issues concerning the safety criteria and options taken with respect to severe accidents, i.e. core melt accidents, giving details on some specific which are less known since they were assessed only lately for Superphenix, sometimes in connection with the on-going safety researches. (author)

Report of the IAEA advisory group meeting on LMFBR fuel reprocessing

International Nuclear Information System (INIS)

1976-05-01

A summary of the papers and discussions of the meeting is presented, reviewing the status of development in LMFBR fuel reprocessing and focusing attention on important problem areas. The following topics are discussed: Transport, storage and removal of sodium; decladding and shearing; dissolution; Purex process; fluoride volatility method; off-gas purification; waste disposal. Status reports of national programmes of Belgium, France, Federal Republic of Germany, Italy, Japan, United Kingdom, USSR and USA are included

Specialists meeting on LMFBR flow induced vibrations. Summary report

International Nuclear Information System (INIS)

1977-12-01

A Specialists' Meeting on LMFBR Flow-Induced Vibrations was held at ANL in the United States which was sponsored by the International Atomic Energy Agency (IAEA) on the recommendations of the International Working Group on Fast Reactors (IWGFR). It was attended by participants from France, the Federal Republic of Germany, Italy, Japan, Netherlands, the United Kingdom, the Union of Soviet Socialist Republics, the United States and the IAEA. The purpose of the meeting was to provide, for the first time, a common forum for the exchange of information on flow-induced vibration programs of the member countries. As this was a first meeting, information was sought in the broad areas of: 1. Design Criteria and Problem Areas in LMFBR Design; 2. Current Design Procedures; and 3. Ongoing Research. A session was devoted to each of the above topics wherein papers were presented and discussed followed by open discussions on the session topic. The objective of the open discussions was to identify, from a review of specific reactor designs, (a) flow induced vibration problem areas (expected and observed) and their potential for occurrence; (b) failure modes and associated design criteria; (c) specific components that are susceptible to flow induced vibration; and (d) probable excitation mechanisms. It was aimed to assess the current state-of-the-art in designing to avoid flow induced vibration with consideration of licensing requirements; to evaluate existing methods of analysis, testing, and surveillance, along with their limitations and to identify areas requiring research and review ongoing research programmes relative to these research needs

Specialists meeting on LMFBR flow induced vibrations. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-12-01

A Specialists' Meeting on LMFBR Flow-Induced Vibrations was held at ANL in the United States which was sponsored by the International Atomic Energy Agency (IAEA) on the recommendations of the International Working Group on Fast Reactors (IWGFR). It was attended by participants from France, the Federal Republic of Germany, Italy, Japan, Netherlands, the United Kingdom, the Union of Soviet Socialist Republics, the United States and the IAEA. The purpose of the meeting was to provide, for the first time, a common forum for the exchange of information on flow-induced vibration programs of the member countries. As this was a first meeting, information was sought in the broad areas of: 1. Design Criteria and Problem Areas in LMFBR Design; 2. Current Design Procedures; and 3. Ongoing Research. A session was devoted to each of the above topics wherein papers were presented and discussed followed by open discussions on the session topic. The objective of the open discussions was to identify, from a review of specific reactor designs, (a) flow induced vibration problem areas (expected and observed) and their potential for occurrence; (b) failure modes and associated design criteria; (c) specific components that are susceptible to flow induced vibration; and (d) probable excitation mechanisms. It was aimed to assess the current state-of-the-art in designing to avoid flow induced vibration with consideration of licensing requirements; to evaluate existing methods of analysis, testing, and surveillance, along with their limitations and to identify areas requiring research and review ongoing research programmes relative to these research needs.

Superalloy applications in the fast breeder reactor

International Nuclear Information System (INIS)

Powell, R.W.

1976-01-01

The economics of the LMFBR are dependent on the breeding of new fuel in the reactor core and this can be improved by the use of advanced alloys as core structural components. The environment of the core makes superalloys a natural choice for these components, but phenomena related directly to neutron irradiation necessitate extensive testing. Consequently, commercially-available superalloys, together with a number of developmental alloys are being tested in existing LMFBR's and by simulation techniques to determine the best alloy for use in the LMFBR core. It presently appears that such materials will indeed be capable of the performance required, and will greatly facilitate the commercial realization of the fast breeder reactor

Confirmatory simulation of safety and operational transients in LMFBR systems

International Nuclear Information System (INIS)

Guppy, J.G.; Agrawal, A.K.

1978-01-01

Operational and safety transients that may originate anywhere in an LMFBR system must be adequately simulated to assist in safety evaluation and plant design efforts. This paper describes an advanced thermohydraulic transient code, the Super System Code (SSC), that may be used for confirmatory safety evaluations of plant wide events, such as assurance of adequate decay heat removal capability under natural circulation conditions, and presents results obtained with SSC illustrating the degree of modelling detail present in the code as well as the computing efficiency. (author)

Preparation of computer codes for analyzing sensitivity coefficients of burnup characteristics (2) (Contract research, translated document)

International Nuclear Information System (INIS)

Hanaki, Hiroshi; Sanda, Toshio; Ohashi, Masahisa

2008-10-01

To develop nuclear design of LMFBR cores, they are important subjects of research and development to improve the accuracy in nuclear design of large LMFBR cores and to design highly efficient core more rationally. The adjusted nuclear cross-sections library has been made by being reflected the result of critical experiment of the JUPITER, etc. effectively as much as possible. And the distinct improvement of the accuracy in nuclear design of large LMFBR cores has been achieved. In the design of large LMFBR cores, however, it is important to accurately estimate not only nuclear characteristics, for example, reaction rate distribution and control rod worth but also burnup characteristics, for example, burnup reactivity loss, breeding ratio and so on. Therefore, it is thought to improve the prediction accuracy for burnup characteristics using many burnup data of 'Joyo' effectively. It is thought the best way to adjust cross sections using sensitivity coefficients of burnup characteristics to utilize burnup data of 'Joyo'. It is able to know the accuracy quantitatively for burnup characteristics of large LMFBR by analyzing the sensitivity coefficients. Therefore in this work computer codes for analyzing sensitivity coefficients of burnup characteristics had been prepared since 1992. In 1992 cross-section adjustment was done by using the data of 'Joyo' and the effect was studied. In this year the adequacy of the codes was studied with a view of applying of design of large LMFBR cores. The results are as follows: (1) The computer codes which could analyze sensitivity coefficients of burnup characteristics taking into consideration plural cycles and refueling were prepared, therefore it came of be able to adjust cross sections using burnup data and to estimate the accuracy for design of large LMFBR cores. The characteristics are not only burnup reactivity loss, breeding ratio but also number density, criticality, reactivity worth, reaction rate ratio, and reaction rate

Users' guide to CACECO containment analysis code. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Peak, R.D.

1979-06-01

The CACECO containment analysis code was developed to predict the thermodynamic responses of LMFBR containment facilities to a variety of accidents. The code is included in the National Energy Software Center Library at Argonne National Laboratory as Program No. 762. This users' guide describes the CACECO code and its data input requirements. The code description covers the many mathematical models used and the approximations used in their solution. The descriptions are detailed to the extent that the user can modify the code to suit his unique needs, and, indeed, the reader is urged to consider code modification acceptable.

Creep strain accumulation in a typical LMFBR piperun

International Nuclear Information System (INIS)

Johnstone, T.L.

1975-01-01

The analysis described allows the strain concentrations in typical LMFBR two anchor point uniplanar piperuns to be calculated. Account is taken of the effect of pipe elbows in attracting creep strain to themselves as well as possible movements of the thrust line due to strain redistribution. The influence of the initial load conditions is also examined. The stress relaxation analysis is facilitated by making the assumption that a cross-sectional stress distribution determined by the asymptotic fully developed state of creep exists at all times. Use is then made of Hoff(s) analogy between materials with a creep law of the Norton type and those with a corresponding non-linear elastic stress strain law, to determine complementary strain energy rates for straight pipes and bends. Ovalisation of the latter produces an increased strain energy rate which can be simply calculated by comparison with an equal length of straight pipe through employing a creep flexibility factor due to Spence. Deflection rates at any location in the pipework can then be evaluated in terms of the thermal restraint forces at that location by an application of Castigliano's principle. In particular for an anchor point the deflection rates are identically zero and this leads to the generation of 3 simultaneous differential equations determining the relaxation of the anchor reactions. Indicative results are presented for the continuous relaxation at 570 deg C of the thermally induced stress in a planar approximation to a typical LMFBR pipe run chosen to have peak elbow stresses close to the code maximum. The results indicate a ratio, after 10 5 hours, of 3 for creep strain concentration relative to initial peak strain (calculated on the assumption of fully elastic behavior) in the most severely affected elbow, when either austenitic 316 or 321 creep properties are employed

Seismic criteria studies and analyses. Quarterly progress report No. 3. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

1975-01-03

Information is presented concerning the extent to which vibratory motions at the subsurface foundation level might differ from motions at the ground surface and the effects of the various subsurface materials on the overall Clinch River Breeder Reactor site response; seismic analyses of LMFBR type reactors to establish analytical procedures for predicting structure stresses and deformations; and aspects of the current technology regarding the representation of energy losses in nuclear power plants as equivalent viscous damping.

LMFBR conceptual design study: an overview of environmental and safety concerns

International Nuclear Information System (INIS)

Brenchley, D.L.

1981-06-01

The US Department of Energy (DOE) initiated the Liquid Metal Fast Breeder (LMFBR) Conceptual Design Study (CDS) with the objective of maintaining a viable breeder option. The project is scheduled to be completed in FY-1981 but decisions regarding plant construction will be delayed until at least 1985. This report provides a review of the potential environmental and safety engineering concerns for the CDS and recommends specific action for the Environmental and Safety Engineering Division of DOE

LMFBR conceptual design study: an overview of environmental and safety concerns

Energy Technology Data Exchange (ETDEWEB)

Brenchley, D.L.

1981-06-01

The US Department of Energy (DOE) initiated the Liquid Metal Fast Breeder (LMFBR) Conceptual Design Study (CDS) with the objective of maintaining a viable breeder option. The project is scheduled to be completed in FY-1981 but decisions regarding plant construction will be delayed until at least 1985. This report provides a review of the potential environmental and safety engineering concerns for the CDS and recommends specific action for the Environmental and Safety Engineering Division of DOE.

Emergency air cleaning system development for LMFBR containments

International Nuclear Information System (INIS)

McCormack, J.D.; Hilliard, R.K.; Postma, A.K.; Muhlestein, L.D.

1975-01-01

Criteria for evaluating the various types of Emergency Air Cleaning Systems which may be used in LMFBR plants have been established for both single containment and containment-confinement arrangements. These two plant arrangements have quite different air cleaning requirements for postulated design base accident conditions. Work is currently in progress to select from a list of candidate air cleaning systems those which best meet the criteria requirements. By means of a weighted rating system, areas of strength or weakness can be found and the conceptual system design then optimized. The final system arrangements will be ranked and several of the most promising systems selected for large-scale tests in the former CSE vessel at Hanford. 8 references. (U.S.)

Structural analysis for LMFBR applications

International Nuclear Information System (INIS)

Vaze, M.K.K.

1983-01-01

The use of elastic analysis for structural design of LMFBR components is discussed. The elastic analysis methods have been used for structural design of the Fast Breeder Test Reactor as well as the proposed Prototype Fast Breeder Reactor. The design of Fast Breeder Test Reactor which is nearing completion is same as that of Rapsodie. Nevertheless, the design had to be checked against the latest design codes available, namely the ASME Code case 1592. This paper however, is confined to Structural analysis of PFBR components. The problems faced in the design of some of the components, in particular, the inner vessel (plenum separator) are discussed. As far as design codes are concerned, ASME Code Section III and the Code Case N-47 are used for high temperature design. The problems faced in the use of these rules are also described along with the description of analysis. Studies in the field of cyclic loading include extension of Bree's shakedown and plastic cycling criteria for ratchet free operation to biaxial stress fields

ARKAS: A three-dimensional finite element code for the analysis of core distortions and mechanical behaviour

International Nuclear Information System (INIS)

Nakagawa, M.

1984-01-01

Computer program ARKAS has been developed for the purpose of predicting core distortions and mechanical behaviour in a cluster of subassemblies under steady state conditions in LMFBR cores. This report describes the analytical models and numerical procedures employed in the code together with some typical results of the analysis made on large LMFBR cores. ARKAS is programmed in the FORTRAN-IV language and is capable of treating up to 260 assemblies in a cluster with flexible boundary conditions including mirror and rotational symmetry. The nonlinearity of the problem due to contact and separation is solved by the step iterative procedure based on the Newton-Raphson method. In each step iterative procedure, the linear matrix equation must be reconstructed and then solved directly. To save computer time and memory, the substructure method is adopted in the step of reconstructing the linear matrix equation, and in the step of solving the linear matrix equation, the block successive over-relaxation method is adopted. The program ARKAS computes, at every time step, 3-dimensional displacements and rotations of the subassemblies in the core and the interduct forces including at the nozzle tips and nozzle bases with friction effects. The code also has an ability to deal with the refueling and shuffling of subassemblies and to calculate the values of withdrawal forces. For the qualitative validation of the code, sample calculations were performed on the several bundle arrays. In these calculations, contact and separation processes under the influences of friction forces, off-center loading, duct rotations and torsion, thermal expansion and irradiation induced swelling and creep were analyzed. These results are quite reasonable in the light of the expected behaviour. This work was performed under the sponsorship of Toshiba Corporation

A fundamental study on sodium-water reaction in the double pool LMFBR, (3)

International Nuclear Information System (INIS)

Uotani, Masaki; Kumagai, Hiromichi; Nishi, Yoshihisa; Yoshida, Kazuo

1989-01-01

The double pool LMFBR is an innovative reactor that Central Research Institute of Electric Power Industry proposed for the purpose of reducing the construction cost of FBRs, and it is characterized by immersing steam generators in the annular plenum formed between the primary vessel and the outer secondary vessel. Therefore, it is expected that the pressure behavior at the time of sodium-water reaction due to the breaking of heating tubes is largely different from the case of steam generators of conventional FBRs. In order to ensure the soundness of the primary vessel that containes the reactor core, it is necessary to sufficiently grasp the pressure behavior in the plenum, and this basic experiment and analysis are related to the pressure behavior due to piston motion that arises in the initial period of quasi-steady pressure. About 1/10 scale annular plenum was used, and the generation of reaction product gas was simulated by the release of nitrogen. When gas was released in the plenum, the highest pressure rise occurred in the initial period of release, and thereafter, periodic variation arose. The pressure waveform and the value of pressure rise as the results of the model analysis agreed well with the measured results. (K.I.)

Deposition of inhaled LMFBR-fuel-sodium aerosols in beagle dogs

International Nuclear Information System (INIS)

Hackett, P.L.; Mahlum, D.D.; Briant, J.K.; Catt, D.L.; Peters, L.R.; Clary, A.J.

1980-01-01

Initial alveolar deposition of LMFBR-fuel aerosols in beagle dogs amounted to 30% of the inhaled activity, but only 5% of the total inhaled activity was deposited in dogs exposed to sodium-fuel aerosols. Aerosol deposition in the gastrointestinal tract amounted to 4% of the initial body burden of fuel-aerosol exposed dogs and 24% of the burden of animals receiving sodium-fuel aerosols. Preliminary analytical data for the dog exposures appear to agree with rodent data for deposition and distribution patterns of aerosols of similar sodium: fuel ratios

LMFBR steam generator leak detection development in the United States

Energy Technology Data Exchange (ETDEWEB)

Magee, P M; Gerrels, E E; Greene, D A [General Electric Company, Sunnyvale, CA (United States); McKee, J [Argonne National Laboratory, Argonne, IL (United States)

1978-10-01

Leak detection for Liquid Metal Fast Breeder Reactor steam generators is an important economic factor in the shutdown, repair and restart of a plant. Development of leak detection systems in the U.S. has concentrated on four areas: (1) chemical (H{sub 2} and O{sub 2}) leak detection meters; (2) acoustic leak detection/location techniques; (3) investigation of leak behavior (enlargement, damage effects, plugging and unplugging); and (4) data management for plant operations. This paper discusses the status, design aspects, and applications of leak detection technology for LMFBR plants. (author)

CAPRICORN subchannel code for sodium boiling in LMFBR fuel bundles

International Nuclear Information System (INIS)

Padilla, A. Jr.; Smith, D.E.; O'Dell, L.D.

1983-01-01

The CAPRICORN computer code analyzes steady-state and transient, single-phase and boiling problems in LMFBR fuel bundles. CAPRICORN uses the same type of subchannel geometry as the COBRA family of codes and solves a similar system of conservation equations for mass, momentum, and energy. However, CAPRICORN uses a different numerical solution method which allows it to handle the full liquid-to-vapor density change for sodium boiling. Results of the initial comparison with data (the W-1 SLSF pipe rupture experiment) are very promising and provide an optimistic basis for proceeding with further development

LMFBR steam generator leak detection development in the United States

International Nuclear Information System (INIS)

Magee, P.M.; Gerrels, E.E.; Greene, D.A.; McKee, J.

1978-01-01

Leak detection for Liquid Metal Fast Breeder Reactor steam generators is an important economic factor in the shutdown, repair and restart of a plant. Development of leak detection systems in the U.S. has concentrated on four areas: (1) chemical (H 2 and O 2 ) leak detection meters; (2) acoustic leak detection/location techniques; (3) investigation of leak behavior (enlargement, damage effects, plugging and unplugging); and (4) data management for plant operations. This paper discusses the status, design aspects, and applications of leak detection technology for LMFBR plants. (author)

Ultra-low velocity zone heterogeneities at the core-mantle boundary from diffracted PKKPab waves

Science.gov (United States)

Ma, Xiaolong; Sun, Xinlei

2017-08-01

Diffracted waves around Earth's core could provide important information of the lowermost mantle that other seismic waves may not. We examined PKKPab diffraction waves from 52 earthquakes occurring at the western Pacific region and recorded by USArray to probe the velocity structure along the core-mantle boundary (CMB). These diffracted waves emerge at distances up to 10° past the theoretical cutoff epicentral distance and show comparable amplitudes. We measured the ray parameters of PKKPab diffraction waves by Radon transform analysis that is suitable for large-aperture arrays. These ray parameters show a wide range of values from 4.250 to 4.840 s/deg, suggesting strong lateral heterogeneities in sampling regions at the base of the mantle. We further estimated the P-wave velocity variations by converting these ray parameters and found the CMB regions beneath the northwestern edge of African Anomaly (Ritsma et al. in Science 286:1925-1928, 1999) and southern Sumatra Islands exhibit velocity reductions up to 8.5% relative to PREM. We suggest that these low velocity regions are Ultra-low velocity zones, which may be related to partial melt or iron-enriched solids.[Figure not available: see fulltext.

Standardization of the methodology used for fuel pressure drop evaluation to improve hydraulic calculation of heterogeneous cores

International Nuclear Information System (INIS)

Le Borgne, E.; Mattei, A.

1994-01-01

Continuous searching for safer and more efficient fuel, and diversification of fuel supply have as a consequence a possible change in the characteristics of the fuel assemblies used in nuclear reactors. By partially refueling cores with new assemblies, nuclear power plant operators are confronted with the problem of heterogeneous cores. The complexity of the problem increases as products diversify in isotopic concentration, types of alloy, size and shape of structure components. This document will focus strictly on the differences in hydraulic resistance related to the modifications in grid structures having no effect on DNB correlations. Although this is an extremely simplified approach to the problem, establishing data to evaluate the hydraulic compatibility between two different assemblies can be difficult, and if not controlled closely, can lead to false conclusions that may affect the operation and safety of the reactor. (authors). 2 figs

LMFBR source term experiments in the Fuel Aerosol Simulant Test (FAST) facility

International Nuclear Information System (INIS)

Petrykowski, J.C.; Longest, A.W.

1985-01-01

The transport of uranium dioxide (UO 2 ) aerosol through liquid sodium was studied in a series of ten experiments in the Fuel Aerosol Simulant Test (FAST) facility at Oak Ridge National Laboratory (ORNL). The experiments were designed to provide a mechanistic basis for evaluating the radiological source term associated with a postulated, energetic core disruptive accident (CDA) in a liquid metal fast breeder reactor (LMFBR). Aerosol was generated by capacitor discharge vaporization of UO 2 pellets which were submerged in a sodium pool under an argon cover gas. Measurements of the pool and cover gas pressures were used to study the transport of aerosol contained by vapor bubbles within the pool. Samples of cover gas were filtered to determine the quantity of aerosol released from the pool. The depth at which the aerosol was generated was found to be the most critical parameter affecting release. The largest release was observed in the baseline experiment where the sample was vaporized above the sodium pool. In the nine ''undersodium'' experiments aerosol was generated beneath the surface of the pool at depths varying from 30 to 1060 mm. The mass of aerosol released from the pool was found to be a very small fraction of the original specimen. It appears that the bulk of aerosol was contained by bubbles which collapsed within the pool. 18 refs., 11 figs., 4 tabs

Subassembly faults diagnostic of an LMFBR type reactor by the measurement of temperature noise

International Nuclear Information System (INIS)

Kokorev, B.V.; Palkin, I.I.; Turchin, N.M.; Pallagi, D.; Horanyi, S.

1979-09-01

The subassembly faults detection possibility by temperature noise analysis of an LMFBR is described. The paper contains the results of diagnostical examinations obtained on electrically heated NaK test rigs. On the basis of these results the measurement of temperature noise RMS value seems to be a practicable method to detect local blockages in an early phase. (author)

Intrafocal heterogeneity of ERG protein expression and gene fusion pattern in prostate cancer.

Science.gov (United States)

Suh, Ja Hee; Park, Jeong Hwan; Lee, Cheol; Moon, Kyung Chul

2017-10-01

Prostate cancer is considered to be highly heterogeneous, with various morphologic features and biologic behaviors. The TMPRSS2-ERG gene fusion is the most frequently observed genetic aberration in prostate cancer. The aim of this study was to elucidate the intrafocal heterogeneity of ERG gene fusion status. ERG immunohistochemistry (IHC) was performed in samples from 168 prostate cancer patients who had undergone radical prostatectomy, and 40 cases showing ERG-positive IHC staining were selected for tissue microarray (TMA) construction. Two to six representative cores were selected from each tumor focus. In the cases with heterogeneous ERG IHC staining intensity, the areas showing different intensities were separately selected. Using the TMA blocks, IHC and fluorescence in situ hybridization (FISH) were conducted to evaluate the heterogeneity of ERG protein expression and ERG fusion gene patterns, respectively, in a single tumor focus. Heterogeneity of ERG IHC staining was defined as the simultaneous presence of negative and positive cores in the same tumor focus. Heterogeneity of ERG FISH was defined by the presence of cores with positive and negative FISH signals or cores with break-apart and interstitial deletion FISH signals in the same tumor focus. A total of 202 TMA cores were isolated from 40 ERG-positive cases. Of the 202 total cores, 19 were negative for ERG IHC staining, and 46 showed 1+, 52 showed 2+, and 85 showed 3+ ERG staining intensity. Eleven cores were negative for ERG FISH signal, 119 cores showed ERG break-apart FISH signals, and the remaining 72 cores revealed interstitial deletion. Intrafocal heterogeneity of ERG IHC staining was found in 20% (8/40) of cases, and intrafocal heterogeneity of ERG gene fusion pattern was found in 32.5% (13/40) of cases. In summary, this study showed significantly frequent intrafocal heterogeneity of ERG protein expression, gene fusion status and fusion pattern. This heterogeneity can be caused by the development

Corrosion critique of the 2 1/4 Cr--1 Mo steel for LMFBR steam generation system applications

International Nuclear Information System (INIS)

Zima, G.E.

1977-07-01

The unstabilized ferritic steel of nominal composition, 2 1 / 4 Cr-1Mo, has been proposed for critical structural assignments in LMFBR powerplants, specifically: the tubing, tubesheet and shell of the evaporator and superheater components. The interest in this steel has been based on a presumably favorable general corrosion property spectrum, acceptable mechanical properties and fabricability, and certain economies associated with the low alloy content. This report is an attempt at a general corrosion assessment for the 2 1 / 4 Cr-1Mo steel and an identification of corrosion problem areas potential to this steel from the sodium and water/steam systems of the proposed working environment. There is a considerable area of uncertainty in the sodium-side response of 2 1 / 4 Cr-1Mo steel, centered in the loss and redisposition of carbon during long-term exposure to sodium of various impurity backgrounds. It is submitted that present evidence relating to the water/steam-side corrosion behavior of the 2 1 / 4 Cr-1Mo steel, under nominal and conceivable perturbed environmental conditions, constitutes the principal concern for the proposed LMFBR powerplant applications of this steel. It is suggested that this unfavorable corrosion aspect represents an inherent limitation of the low alloy content of this steel, probably largely independent of melting and processing recourses, and it is a sufficient basis to question the incentive for a continuation of the collateral studies of this steel for the proposed LMFBR steam generation system assignments

Evaluation of integrally finned cladding for LMFBR fuel pins

International Nuclear Information System (INIS)

Cantley, D.A.; Sutherland, W.H.

1975-01-01

An integral fin design effectively reduces the coolant temperature gradients within an LMFBR subassembly by redistributing coolant flow so as to reduce the maximum cladding temperature and increase the duct wall temperature. The reduced cladding temperatures are offset by strain concentrations resulting from the fin geometry, so there is little net effect on predicted fuel pin performance. The increased duct wall temperatures, however, significantly reduce the duct design lifetime so that the final conclusion is that the integral fin design is inferior to the standard wire wrap design. This result, however, is dependent upon the material correlations used. Advanced alloys with improved irradiation properties could alter this conclusion

Acoustic leak detection of LMFBR steam generator

International Nuclear Information System (INIS)

Kumagai, Hiromichi; Yoshida, Kazuo

1993-01-01

The development of a water leak detector with short response time for LMFBR steam generators is required to prevent the failure propagation caused by the sodium-water reaction and to maintain structural safety in steam generators. The development of an acoustic leak detector assuring short response time has attracted. The purpose of this paper is to confirm the basic detection feasibility of the active acoustic leak detector, and to investigate the leak detection method by erasing the background noise by spectrum analysis of the passive acoustic leak detector. From a comparison of the leak detection sensitivity of the active and the passive method, the active method is not influenced remarkably by the background noise, and it has possibility to detect microleakage with short response time. We anticipate a practical application of the active method in the future. (author)

Fatigue of LMFBR piping due to flow stratification

International Nuclear Information System (INIS)

Woodward, W.S.

1983-01-01

Flow stratification due to reverse flow was simulated in a 1/5-scale water model of a LMFBR primary pipe loop. The stratified flow was observed to have a dynamic interface region which oscillated in a wave pattern. The behavior of the interface was characterized in terms of location, local temperature fluctuation and duration for various reverse flow conditions. A structural assessment was performed to determine the effects of stratified flow on the fatigue life of the pipe. Both the static and dynamic aspects of flow stratification were examined. The dynamic interface produces thermal striping on the inside of the pipe wall which is shown to have the most deleterious effect on the pipe wall and produce significant fatigue damage relative to a static interface

Fatigue of LMFBR piping due to flow stratification

Energy Technology Data Exchange (ETDEWEB)

Woodward, W.S.

1983-01-01

Flow stratification due to reverse flow was simulated in a 1/5-scale water model of a LMFBR primary pipe loop. The stratified flow was observed to have a dynamic interface region which oscillated in a wave pattern. The behavior of the interface was characterized in terms of location, local temperature fluctuation and duration for various reverse flow conditions. A structural assessment was performed to determine the effects of stratified flow on the fatigue life of the pipe. Both the static and dynamic aspects of flow stratification were examined. The dynamic interface produces thermal striping on the inside of the pipe wall which is shown to have the most deleterious effect on the pipe wall and produce significant fatigue damage relative to a static interface.

85,000-GPM, single-stage, single-suction LMFBR intermediate centrifugal pump

International Nuclear Information System (INIS)

Fair, C.E.; Cook, M.E.; Huber, K.A.; Rohde, R.

1983-01-01

The mechanical and hydraulic design features of the 85,000-gpm, single-stage, single-suction pump test article, which is designed to circulate liquid-sodium coolant in the intermediate heat-transport system of a Large-Scale Liquid Metal Fast Breeder Reactor (LS-LMFBR), are described. The design and analytical considerations used to satisfy the pump performance and operability requirements are presented. The validation of pump hydraulic performance using a hydraulic scale-model pump is discussed, as is the featute test for the mechanical-shaft seal system

Design considerations for large heterogeneous liquid-metal fast breeder reactors

International Nuclear Information System (INIS)

Tzanos, C.P.; Barthold, W.P.

1977-01-01

A systematic method for designing heterogeneous configurations having a near-zero value of sodium void reactivity is presented. It is based on the following principles: (a) the thickness of the internal blanket zones should be such that the reactivity change resulting from voiding any core zone is practically independent of any further increase in the thickness of these zones, and (b) the sodium void reactivity of each core zone must have a near-zero value. Neutronic coupling among the core zones of heterogeneous configurations decreases as the thickness of the internal blanket zones increases. To quantify coupling, Avery's coupling coefficients are used. Reduced coupling among the core zones of a heterogeneous design, compared to a homogeneous design, results in (a) increased sensitivity of the power distribution to enrichment distribution perturbations, (b) reduced reactivity worth of local perturbations, and (c) higher cladding temperatures during operational transients initiated by local perturbations. Heterogeneous designs compared to equivalent homogeneous designs have (a) lower core Doppler coefficient values, (b) larger fuel compaction reactivities, and (c) higher maximum cladding temperatures

Fission and corrosion products behavior in primary circuits of LMFBR's

International Nuclear Information System (INIS)

Feuerstein, H.; Thorley, A.W.

1987-08-01

Most of the 20 presented papers report items belonging to more than one session. The equipment results of primary circuits of LMFBR's relative to corrosion and fission products, release and chemistry of fuel, measurement techniques and analytical procedures of sodium sampling, difficulties with radionuclides and particles, reactor experiences with EBR-II, FFTF, BR10, BOR60, BN350, BN600, JOYO, and KNK-II, DFR, PFR, RAPSODIE, PHENIX, and SUPERPHENIX, and at least the verification of codes for calculation models of radioactive products accumulation and distribution are described. All 20 papers presented at the meeting are separately indexed in the database. (DG)

Study of thermal-hydraulic characteristics in an LMFBR intermediate plenum

International Nuclear Information System (INIS)

Uotani, M.; Naohara, N.; Kinoshita, I.

1985-01-01

Experimental studies using water and liquid metal were conducted in order to investigate the thermal-hydraulic characteristics of an LMFBR intermediate plenum. The present study is an attempt to evaluate the effect of natural convection on the temperature field and to validate the prediction method of temperature profile in a thermally stratified cavity. The experimental results indicated that the effect of the natural convection on flow velocity and heat transfer in the cavity is reduced with increasing the modified stratification parameter. The calculation by FEM code and a simple 1-D model are effective to predict the temperature profile in the cavity

Sodium mists behavior in cover gas space of an LMFBR

International Nuclear Information System (INIS)

Himeno, Y.; Takahashi, J.

1978-03-01

This paper present the sodium mist behavior in Argon cover gas space of an LMFBR experimentally using a test vessel of 1,400 mm in axial length, 305.5 mm in inner diameter and about 100 l in volume. Experiments are consisted with measurements of the mist concentration and the mist gravitational settling flux between the sodium pool temperature range of 290 0 to 520 0 C. The results are discussed under the monosize assumption of the particles, and the particle sizes and evaporation rate are derived. Transient and steady state mist concentration behavior were also investigated. (author)

Techniques for the thermal/hydraulic analysis of LMFBR check valves

International Nuclear Information System (INIS)

Cho, S.M.; Kane, R.S.

1979-01-01

A thermal/hydraulic analysis of the check valves in liquid sodium service for LMFBR plants is required to provide temperature data for thermal stress analysis of the valves for specified transient conditions. Because of the complex three-dimensional flow pattern within the valve, the heat transfer analysis techniques for less complicated shapes could not be used. This paper discusses the thermal analysis techniques used to assure that the valve stress analysis is conservative. These techniques include a method for evaluating the recirculating flow patterns and for selecting appropriately conservative heat transfer correlations in various regions of the valve

LMFBR system-wide transient analysis: the state of the art and US validation needs

International Nuclear Information System (INIS)

Khatib-Rahbar, M.; Guppy, J.G.; Cerbone, R.J.

1982-01-01

This paper summarizes the computational capabilities in the area of liquid metal fast breeder reactor (LMFBR) system-wide transient analysis in the United States, identifies various numerical and physical approximations, the degree of empiricism, range of applicability, model verification and experimental needs for a wide class of protected transients, in particular, natural circulation shutdown heat removal for both loop- and pool-type plants

Specialists meeting on leak detection and location in LMFBR steam generators. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1978-10-01

The following topics covered at the meeting were: with leak detection and location methods and equipment, including concentration measurements, helium tests, and electromagnetic methods; acoustic leak detection and related equipment; techniques and experiences in ensuring and measuring steam generator tightness during manufacturing, installation and repair, tube inspection methods for periodic control and damage assessment following leaks, influence of these methods on design of steam generators for LMFBR type reactors.

Specialists meeting on leak detection and location in LMFBR steam generators. Summary report

International Nuclear Information System (INIS)

1978-10-01

The following topics covered at the meeting were: with leak detection and location methods and equipment, including concentration measurements, helium tests, and electromagnetic methods; acoustic leak detection and related equipment; techniques and experiences in ensuring and measuring steam generator tightness during manufacturing, installation and repair, tube inspection methods for periodic control and damage assessment following leaks, influence of these methods on design of steam generators for LMFBR type reactors

Research report on design allowable values of structural materials for LMFBR

International Nuclear Information System (INIS)

1978-11-01

The present report is composed of following two main parts. i) review and re-evaluation on test results by FCI Sub-committee studies, performed from 1973 to 1976, ii) review on procedures for determining design allowable values of structural materials for LMFBR components. Re-evaluation works have been made on monotonic tensile properties at elevated temperatures, creep and creep rupture properties, creep-fatigue properties (strain rate and tensile strain hold time effects on strain fatigue properties at elevated temperatures) of Types 316 and 304 stainless steel and 2 1/4Cr-1Mo steel (base and weld metals) produced in Japan. In the first half of the present report, creep-fatigue test results obtained by FCI Sub-committee studies are subjected to re-evaluation by the present P-FCI Sub-committee. Reviews have been made on testing methods on FCI's-creep-fatigue experiments with other test data of the test materials; high temperature monotonic tensile data, creep and creep rupture data, and origin of the test materials. The data of FCI studies are compared with other reference data obtained by several Japanese laboratories. In the latter half of the present report, procedures including ASME's are reviewed for setting design allowable values for LMFBR components on the basis of high temperature strength properties obtained with materials produced in Japan. A creep rupture data of Japanese steels are issued and examined to make proposal for a design allowable stress of S sub(t) through parameter survey. (author)

Effects of entrained gas on the acoustic detection of sodium boiling in a simulated LMFBR fuel bundle

International Nuclear Information System (INIS)

Leavell, W.H.; Sides, W.H.

1975-01-01

The relationship between acoustic intensity of nucleate boiling and void fraction was studied in a simulated LMFBR fuel bundle. Results indicate that as the void fraction increases the detected intensity of nucleate boiling decreased until it was indistinguishable from background noise. (JWR)

Structural analysis for LMFBR applications

International Nuclear Information System (INIS)

1983-01-01

Firstly, we discuss the use of elastic analysis for structural design of LMFBR components. The elastic analysis methods have been used for structural design of the Fast Breeder Test Reactor as well as the proposed prototype Test Breeder Reactor. The design of Fast Breeder Test Reactor which is nearing completion is the same as that of Rapsodie. Nevertheless, the design had to he checked against the latest design codes available, namely the ASME Code case 1592. This paper however, is confined to Structural analysis of PFBR components. The problems faced in the design of some of the components, in particular, the inner vessel (plenum separator) are discussed. As far as design codes are concerned, we make use of ASME Code Section III and the Code Case N-47, for high temperature design. The problem faced in the use of these rules are also described along with the description of analysis. Studies in the field of cyclic loading include extension of Bree's breakdown and plastic cycling criteria for ratchet free operation to biaxial stress fields. In other fields, namely, inelastic analysis, piping analysis in the creep regime etc. we are only at a start

The radiological significance of transuranium radioisotopes released to the environment during operation of the LMFBR fuel cycle

International Nuclear Information System (INIS)

Barr, N.F.

1976-01-01

Estimates based on current knowledge and conservative assumptions indicate that release of transuranium elements from the Liquid Metal Fast Breeder Reactor (LMFBR) fuel cycle are likely to proaduce population dose commitments small compared to those produced by naturally occurring alpha emitters and globally dispersed transuranium radioisotopes from tests of nuclear weapons in the atmosphere. Potential health consequences of these releases to current and future generations are estimated to be very small compared to risks associated with the production of energy by fossil fuels. The estimates are subject to a number of uncertainties imposed by lack of knowledge. Some of the uncertainties are not likely to be greatly reduced until LMFBR facilities are designed and operated. Others may be significantly reduced prior to facility design and operation. The paper discusses the sensitivity of the estimates to uncertainties and approches to reducing those uncertainties that strongly influence the estimates. (author)

PNC status report on leak detector development for LMFBR steam generators

International Nuclear Information System (INIS)

Kuroha, M.; Sato, M.

1984-01-01

Chemical and acoustic type leak detectors have been developed for detecting a small sodium-water reaction in an LMFBR steam generator. This paper presents a summary of the development. (1) Test results on PNC type in-sodium hydrogen meters including a description of the structure, the long-term reliability and the durability, and the improved meter with an orifice, (2) Development of in-cover gas hydrogen meters, (3) Hydrogen detection tests and analyses, (4) Operating experiences of electrochemical in-sodium oxygen meters, and (5) Basic studies on acoustic characteristics of the sodium-water reaction. (author)

LMFBR steam generator development: duplex bayonet tube steam generator. Volume II

International Nuclear Information System (INIS)

DeFur, D.D.

1975-04-01

This report represents the culmination of work performed in fulfillment of ERDA Contract AT(11-1)-2426, Task Agreement 2, in which alternate steam generator designs were developed and studied. The basic bayonet tube generator design previously developed by C-E under AEC Contract AT(11-1)-3031 was expanded by incorporating duplex heat transfer tubes to enhance the unit's overall safety and reliability. The effort consisted of providing and evaluating conceptual designs of the evaporator, superheater and reheater components for a large plant LMFBR steam generator (950 MWt per heat transport loop)

Fast reactor core concepts to improve transmutation efficiency

International Nuclear Information System (INIS)

Fujimura, Koji; Kawashima, Katsuyuki; Itooka, Satoshi

2015-01-01

Fast Reactor (FR) core concepts to improve transmutation efficiency were conducted. A heterogeneous MA loaded core was designed based on the 1000MWe-ABR breakeven core. The heterogeneous MA loaded core with Zr-H loaded moderated targets had a better transmutation performance than the MA homogeneous loaded core. The annular pellet rod design was proposed as one of the possible design options for the MA target. It was shown that using annular pellet MA rods mitigates the self-shielding effect in the moderated target so as to enhance the transmutation rate

Reactor core in FBR type reactor

International Nuclear Information System (INIS)

Masumi, Ryoji; Kawashima, Katsuyuki; Kurihara, Kunitoshi.

1989-01-01

In a reactor core in FBR type reactors, a portion of homogenous fuels constituting the homogenous reactor core is replaced with multi-region fuels in which the enrichment degree of fissile materials is lower nearer to the axial center. This enables to condition the composition such that a reactor core having neutron flux distribution either of a homogenous reactor core or a heterogenous reactor core has substantially identical reactivity. Accordingly, in the transfer from the homogenous reactor core to the axially heterogenous reactor core, the average reactivity in the reactor core is substantially equal in each of the cycles. Further, by replacing a portion of the homogenous fuels with a multi-region fuels, thereby increasing the heat generation near the axial center, it is possiable to reduce the linear power output in the regions above and below thereof and, in addition, to improve the thermal margin in the reactor core. (T.M.)

Overview of the fast reactors fuels program. [LMFBR

Energy Technology Data Exchange (ETDEWEB)

Evans, E.A.; Cox, C.M.; Hayward, B.R.; Rice, L.H.; Yoshikawa, H.H.

1980-04-01

Each nation involved in LMFBR development has its unique energy strategies which consider energy growth projections, uranium resources, capital costs, and plant operational requirements. Common to all of these strategies is a history of fast reactor experience which dates back to the days of the Manhatten Project and includes the CLEMENTINE Reactor, which generated a few watts, LAMPRE, EBR-I, EBR-II, FERMI, SEFOR, FFTF, BR-1, -2, -5, -10, BOR-60, BN-350, BN-600, JOYO, RAPSODIE, Phenix, KNK-II, DFR, and PFR. Fast reactors under design or construction include PEC, CRBR, SuperPhenix, SNR-300, MONJU, and Madras (India). The parallel fuels and materials evolution has fully supported this reactor development. It has involved cermets, molten plutonium alloy, plutonium oxide, uranium metal or alloy, uranium oxide, and mixed uranium-plutonium oxides and carbides.

Statistical mechanical analysis of LMFBR fuel cladding tubes

International Nuclear Information System (INIS)

Poncelet, J.-P.; Pay, A.

1977-01-01

The most important design requirement on fuel pin cladding for LMFBR's is its mechanical integrity. Disruptive factors include internal pressure from mixed oxide fuel fission gas release, thermal stresses and high temperature creep, neutron-induced differential void-swelling as a source of stress in the cladding and irradiation creep of stainless steel material, corrosion by fission products. Under irradiation these load-restraining mechanisms are accentuated by stainless steel embrittlement and strength alterations. To account for the numerous uncertainties involved in the analysis by theoretical models and computer codes statistical tools are unavoidably requested, i.e. Monte Carlo simulation methods. Thanks to these techniques, uncertainties in nominal characteristics, material properties and environmental conditions can be linked up in a correct way and used for a more accurate conceptual design. (Auth.)

Fretting and wear of stainless and ferritic steels in LMFBR steam generators

International Nuclear Information System (INIS)

Lewis, M.W.J.; Campbell, C.S.

1981-01-01

Steam generators for LMFBR's may be subject to both fretting wear as a result of flow-induced vibrations and to wear from larger amplitude sliding movements from thermal changes. Results of tests simulating the latter are given for stainless and ferritic steels. For the assessment of fretting wear damage, vibration assessments must be combined with data on specific wear rates. Test mechanisms used to study fretting in sodium covering impact, impact-slide and pure rubbing are described and results presented. (author)

In-pile TREAT Test L04: simulating a lead sub-assembly in an unprotected LMFBR loss-of-coolant accident

International Nuclear Information System (INIS)

Tylka, J.P.; Bauer, T.H.; Wright, A.E.; Davies, A.L.; Herbert, R.; Woods, W.J.

1983-01-01

Test L04 in the PFR/TREAT series is the first multi-pin, in-pile simulation of a LMFBR transient undercooling/overpower (TUCOP) accident using full length prototypic fuel irradiated in a fast reactor. L04 is a gridded 7-pin bundle test performed in the ANL Mk-III integral loop in a flowing sodium environment and uses prototypic, bottom plenum, UK reactor fuel, preirradiated in the PFR to an axial peak burn-up of 4.2 a/o. The objective of L04 was the study, by simulation, of coolant voiding and fuel motion during the initiating phase of a hypothetical TUCOP accident in a large LMFBR. Test L04 is intended to study the behavior of a centrally located, lead subassembly with the highest power-to-flow ratio

Acoustic detection for water/steam leak from a tube of LMFBR steam generator

International Nuclear Information System (INIS)

Sonoda, Masataka; Shindo, Yoshihisa

1989-01-01

Acoustic leak detector is useful for detecting more quickly intermediate leak than the existing hydrogen detector and is available for identification of leak location on the accident of water/steam leak from a tube of LMFBR steam generator. This paper presents the overview of HALD (High frequency Acoustics Leak Detection) system, which is more sensitive for leak detection and lower cost of equipment for identification of leak location than a low frequency type detector. (author)

Internal fuel motion as an inherent shutdown mechanism for LMFBR accidents: PINEX-3, PINEX-2, and HUT 5-2A experiments

International Nuclear Information System (INIS)

Ferrell, P.C.; Porten, D.R.; Martin, F.J.

1981-01-01

The PINEX-2 experiment verified the concept of axial internal molten fuel motion within annular fuel, representing an inherent shutdown mechanism for hypothetical transient overpower excursions on the order of 5$/s. The PINEX-3 experiment, simulating a 50 cents/s transient overpower, showed that limitations on the effectiveness of fuel motion may arise from freezing of the fuel and blockage of the internal movement. Analysis of these experiments was performed to assess the physical processes that dominate fuel relocation potential and to apply them to prototypic LMFBR pin conditions. Results indicate that internal fuel motion should be reliable as a shutdown mechanism in LMFBR's for a range of reactivity insertion rates beyond presently available experimental data

Complementary role of critical integral experiment and power reactor start-up experiments for LMFBR neutronics data and method validation

International Nuclear Information System (INIS)

Salvatores, M.

1986-09-01

Both critical experiments and power reactor results play at present a complementary role in reducing the uncertainties in Key design parameters for LMFBR, which can be relevant for the economic performances of this type of reactors

Benchmark physics experiment of metallic-fueled LMFBR at FCA. 2

International Nuclear Information System (INIS)

Iijima, Susumu; Oigawa, Hiroyuki; Ohno, Akio; Sakurai, Takeshi; Nemoto, Tatsuo; Osugi, Toshitaka; Satoh, Kunio; Hayasaka, Katsuhisa; Bando, Masaru.

1993-10-01

An availability of data and method for a design of metallic-fueled LMFBR is examined by using the experiment results of FCA assembly XVI-1. Experiment included criticality and reactivity coefficients such as Doppler, sodium void, fuel shifting and fuel expansion. Reaction rate ratios, sample worth and control rod worth were also measured. Analysis was made by using three-dimensional diffusion calculations and JENDL-2 cross sections. Predictions of assembly XVI-1 reactor physics parameters agree reasonably well with the measured values, but for some reactivity coefficients such as Doppler, large zone sodium void and fuel shifting further improvement of calculation method was need. (author)

Transient behaviour and inherent safety research of LMFBR power plants

International Nuclear Information System (INIS)

Zhu Jizhou; Wang Ping; Yu Baoan

1995-06-01

Fast Breeder Reactor will be the next generation reactor for nuclear electricity production, the development of FBR will give the profits of efficient utilization of nuclear resources. The fast reactor safety analysis is the foundation and key of FBR research work. Therefore, a block-oriented mathematical model for the primary system of LMFBRs was constructed, and the dynamic simulating results which have been carried out on micro-computer are presented for various transients, i.e. TOP, LOFS, LOHS. The results agree well with the corresponding results of the code NATDEMO and experiment results of EBR-II. Based on previous analysis, various methods are discussed to confirm the inherent safety of LMFBR

LMFBR fuel cycle studies progress report, August 1972, No. 42

International Nuclear Information System (INIS)

Unger, W.E.; Blanco, R.E.; Crouse, D.J.; Irvine, A.R.; Watson, C.D.

1972-10-01

This report continues a series outlining progress in the development of methods for reprocessing of LMFBR fuels. Development work is reported on problems of irradiated fuel transport to the processing facility, the dissolution of the fuel and the chemical recovery of PuO 2 --UO 2 values, the containment of volatile fission products, product purification, conversion of fuel processing plant product nitrate solutions to solids suitable for shipping and for subsequent fuel fabrication. Pertinent experimental results are presented for the information of those immediately concerned with the field. Detailed description of experimental work and data are included in the topical reports and in the Chemical Technology Division Annual Reports

Component mode synthesis methods for 3-D heterogeneous core calculations applied to the mixed-dual finite element solver MINOS

International Nuclear Information System (INIS)

Guerin, P.; Baudron, A.M.; Lautard, J.J.; Van Criekingen, S.

2007-01-01

This paper describes a new technique for determining the pin power in heterogeneous three-dimensional calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis (CMS) technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions. In the first one (the CMS method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (factorized CMS method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher-order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher-order angular approximations-particularly easily to an SPN approximation-the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with uranium dioxide and mixed oxide assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

Sodium fire studies in France safety tests and applications on an LMFBR

International Nuclear Information System (INIS)

Fruchard, Y.; Colome, J.; Malet, J.C.; Berlin, M.; de Cuy, G.D.; Justin, J.; Duco, J.; Fourest, B.

1976-01-01

The risk of sodium fires in an LMFBR requires thorough analysis, and the possible consequences of an accidental fire must be accurately determined. Not only must means of prevention and detection be perfected, but techniques must be developed to limit the damage caused by a fire: extinguishment, aerosol containment, protection of reactor structures. The program currently undertaken by the CEA's Nuclear Safety Department covering these problems is described. The major results obtained as well as their application to the SUPER-PHENIX reactor are included

Estimation of the mechanical effects of a core disruptive accident on a LMFBR

International Nuclear Information System (INIS)

Robbe, M.F.; Lepareux, M.; Treille, E.

2001-01-01

In case of a Hypothetical Core Disruptive Accident (HCDA) in a Liquid Metal Reactor, the interaction between fuel and liquid sodium creates a high pressure gas bubble in the core. The violent expansion of this bubble loads the vessel and the internal structures, whose deformation is important. In order to demonstrate the CASTEM-PLEXUS capability to predict the behaviour of real reactors], axisymmetric computations of the MARA series were confronted with the experimental results. The computations performed at the beginning of the years 90 showed a rather good agreement between the experimental and computed results for the MARA 8 and MARA 10 tests even if there were some discrepancies which might be eliminated by increasing the fineness of the mesh. On the contrary, the prediction of the MARS structure displacements and strains was overestimated. This conservatism was supposed to come from the fact that several MARS non axisymmetric structures like core elements, pumps and heat exchangers were not represented in the CASTEM-PLEXUS model. These structures, acting as porous barriers, had a protective effect on the containment by absorbing energy and slowing down the fluid impacting the containment. For these reasons, we developed in CASTEM-PLEXUS a new HCDA constitutive law taking into account the presence of the internal structures (without meshing them) by means of an equivalent porosity method and we simulated the MARS test another time with the new HCDA constitutive law. This paper presents the numerical results relative to the structure behaviour during the accident. The results are described through the evolution of several variables versus time: deformed shape of the structures and the mesh, displacements, stresses and plastic strains. (author)

SIMMER-II: A computer program for LMFBR disrupted core analysis

Energy Technology Data Exchange (ETDEWEB)

Bohl, W.R.; Luck, L.B.

1990-06-01

SIMMER-2 (Version 12) is a computer program to predict the coupled neutronic and fluid-dynamics behavior of liquid-metal fast reactors during core-disruptive accident transients. The modeling philosophy is based on the use of general, but approximate, physics to represent interactions of accident phenomena and regimes rather than a detailed representation of specialized situations. Reactor neutronic behavior is predicted by solving space (r,z), energy, and time-dependent neutron conservation equations (discrete ordinates transport or diffusion). The neutronics and the fluid dynamics are coupled via temperature- and background-dependent cross sections and the reactor power distribution. The fluid-dynamics calculation solves multicomponent, multiphase, multifield equations for mass, momentum, and energy conservation in (r,z) or (x,y) geometry. A structure field with nine density and five energy components; a liquid field with eight density and six energy components; and a vapor field with six density and on energy component are coupled by exchange functions representing a modified-dispersed flow regime with a zero-dimensional intra-cell structure model.

SIMMER-II: A computer program for LMFBR disrupted core analysis

International Nuclear Information System (INIS)

Bohl, W.R.; Luck, L.B.

1990-06-01

SIMMER-2 (Version 12) is a computer program to predict the coupled neutronic and fluid-dynamics behavior of liquid-metal fast reactors during core-disruptive accident transients. The modeling philosophy is based on the use of general, but approximate, physics to represent interactions of accident phenomena and regimes rather than a detailed representation of specialized situations. Reactor neutronic behavior is predicted by solving space (r,z), energy, and time-dependent neutron conservation equations (discrete ordinates transport or diffusion). The neutronics and the fluid dynamics are coupled via temperature- and background-dependent cross sections and the reactor power distribution. The fluid-dynamics calculation solves multicomponent, multiphase, multifield equations for mass, momentum, and energy conservation in (r,z) or (x,y) geometry. A structure field with nine density and five energy components; a liquid field with eight density and six energy components; and a vapor field with six density and on energy component are coupled by exchange functions representing a modified-dispersed flow regime with a zero-dimensional intra-cell structure model

Noise and DC balanced outlet temperature signals for monitoring coolant flow in LMFBR fuel elements

International Nuclear Information System (INIS)

Edelmann, M.

1977-01-01

Local cooling disturbances in LMFBR fuel elements may have serious safety implications for the whole reactor core. They have to be detected reliably in an early stage of their formation therefore. This can be accomplished in principle by individual monitoring of the coolant flow rate or the coolant outlet temperature of the sub-assemblies with high precision. In this paper a method is proposed to increase the sensitivity of outlet temperature signals to cooling disturbances. Using balanced temperature signals provides a means for eliminating the normal variations from the original signals which limit the sensitivity and speed of response to cooling disturbances. It is shown that a balanced signal can be derived easily from the original temperature signal by subtracting an inlet temperature and a neutron detector signal with appropriate time shift. The method was tested with tape-recorded noise signals of the KNK I reactor at Karlsruhe. The experimental results confirm the theoretical predictions. A significant reduction of the uncertainty of measured outlet temperatures was achieved. This enables very sensitive and fast response monitoring of coolant flow. Furthermore, it was found that minimizing the variance of the balanced signal offers the possibility for a rough determination of the heat transfer coefficient of the fuel rods during normal reactor operation at power. (author)

Recent development of a CEC'S elasto-plastic-creep cyclic benchmark programme relevant to LMFBR structural integrity

International Nuclear Information System (INIS)

Corsi, F.; Terzaghi, A.

1984-01-01

It's presented the programme of elasto-plastic benchmark calculations relevant to LMFBr, which started in 1977 with the support and coordination of the Commission of the European Communities (CEC) and the participation of nuclear engineering and manufacturing companies as well as nuclear research centers of France, Germany, Italy and the United Kingdom. (E.G.) [pt

Steam generating system in LMFBR type reactors

International Nuclear Information System (INIS)

Kurosawa, Katsutoshi.

1984-01-01

Purpose: To suppress the thermal shock loads to the structures of reactor system and secondary coolant system, for instance, upon plant trip accompanying turbine trip in the steam generation system of LMFBR type reactors. Constitution: Additional feedwater heater is disposed to the pipeway at the inlet of a steam generator in a steam generation system equipped with a closed loop extended from a steam generator by way of a gas-liquid separator, a turbine and a condensator to the steam generator. The separated water at high temperature and high pressure from a gas-liquid separator is heat exchanged with coolants flowing through the closed loop of the steam generation system in non-contact manner and, thereafter, introduced to a water reservoir tank. This can avoid the water to be fed at low temperature as it is to the steam generator, whereby the thermal shock loads to the structures of the reactor system and the secondary coolant system can be suppressed. (Moriyama, K.)

A fundamental study on sodium-water reaction in the double-pool-type LMFBR

International Nuclear Information System (INIS)

Yoshida, Kazuo; Akimoto, Tokuzo

1987-01-01

In order to evaluate the pressure rise by large sodium-water reaction in the Double-Pool LMFBR, basic tests on pressure wave celerity in rectangular tube are carried out. The initial spike pressure in rectangular-shelled steam generator of the Double Pool reactor, strongly depends on pressure wave celerity. In this study, celerity was measured as a function of pressure wave rising time and pulse height, and influence of water around the test section on celerity was investigated. (author)

Development of an 85,000 gpm (19,303 m3/h) LMFBR primary pump

International Nuclear Information System (INIS)

Zerinvary, M.C.; Wagner, E.W.

1984-01-01

The development of an 85,000 gpm two-stage primary pump for liquid metal fast breeder reactor (LMFBR) applications is described. The design was supported by air and cavitation model testing of the hyraulics, and development and feature testing of the level control system and the adjustable frequency solid state power supply. Important fabrication and water test items are also discussed, along with some unique assembly tooling requirements

LOA-1: prevent accidents. Quarterly technical progress report, FRSP program - July through September 1981

International Nuclear Information System (INIS)

1981-01-01

Information related to LMFBR reactor safety is presented concerning common cause failures; shutdown by self-activated system; shutdown heat removal system operation; sodium burning; core catcher material interactions; accident release of sodium oxide aerosol; and LMFBR risk assessment

Analytical methods to characterize heterogeneous raw material for thermal spray process: cored wire Inconel 625

Science.gov (United States)

Lindner, T.; Bonebeau, S.; Drehmann, R.; Grund, T.; Pawlowski, L.; Lampke, T.

2016-03-01

In wire arc spraying, the raw material needs to exhibit sufficient formability and ductility in order to be processed. By using an electrically conductive, metallic sheath, it is also possible to handle non-conductive and/or brittle materials such as ceramics. In comparison to massive wire, a cored wire has a heterogeneous material distribution. Due to this fact and the complex thermodynamic processes during wire arc spraying, it is very difficult to predict the resulting chemical composition in the coating with sufficient accuracy. An Inconel 625 cored wire was used to investigate this issue. In a comparative study, the analytical results of the raw material were compared to arc sprayed coatings and droplets, which were remelted in an arc furnace under argon atmosphere. Energy-dispersive X-ray spectroscopy (EDX) and X-ray fluorescence (XRF) analysis were used to determine the chemical composition. The phase determination was performed by X-ray diffraction (XRD). The results were related to the manufacturer specifications and evaluated in respect to differences in the chemical composition. The comparison between the feedstock powder, the remelted droplets and the thermally sprayed coatings allows to evaluate the influence of the processing methods on the resulting chemical and phase composition.

LMFBR type reactors

International Nuclear Information System (INIS)

Sakurai, Akio; Matsushita, Kazuo.

1985-01-01

Purpose: To surely prevent the vibrational displacement of a rector core, and remove the sliding portions so as to avoid sticking or localized load concentration. Constitution: Cylindrical vibration-damping walls are protruded from the inner surface at the bottom of the main vessel. The vibration-damping walls constituted with outer and inner walls defining a coolant passage surround the reactor core support structures with small gaps between the inner surface of the inner wall and the outer circumferential surface of the core support structures. If the core support structures tend to displace horizontally due to earthquakes or the likes, the small gaps are varied and the coolants flow through the gap. Vibration-damping for the core support structures can be obtained by the flowing resistance to the coolants. (Yoshino, Y.)

Measurement and analysis of neutron flux distribution of STACY heterogeneous core by position sensitive proportional counter. Contract research

CERN Document Server

Murazaki, M; Uno, Y

2003-01-01

We have measured neutron flux distribution around the core tank of STACY heterogeneous core by position sensitive proportional counter (PSPC) to develop the method to measure reactivity for subcritical systems. The neutron flux distribution data in the position accuracy of +-13 mm have been obtained in the range of uranium concentration of 50g/L to 210g/L both in critical and in subcritical state. The prompt neutron decay constant, alpha, was evaluated from the measurement data of pulsed neutron source experiments. We also calculated distribution of neutron flux and sup 3 He reaction rates at the location of PSPC by using continuous energy Monte Carlo code MCNP. The measurement data was compared with the calculation results. As results of comparison, calculated values agreed generally with measurement data of PSPC with Cd cover in the region above half of solution height, but the difference between calculated value and measurement data was large in the region below half of solution height. On the other hand, ...

Quasi-steady state boiling downstream of a central blockage in a 19-rod simulated LMFBR subassembly (FFM bundle 3B)

International Nuclear Information System (INIS)

Hanus, N.; Fontana, M.H.; Gnadt, P.A.; MacPherson, R.E.; Smith, C.M.; Wantland, J.L.

1976-01-01

Results of sodium boiling tests in a centrally blocked 19-rod simulated LMFBR subassembly are discussed. The tests were part of the experimental series conducted with bundle 3B in the Fuel Failure Mockup (FFM) at ORNL

Study on the phenomena of natural circulation in LMFBR

International Nuclear Information System (INIS)

Takeda, Hirofumi; Koga, Tomonari

1993-01-01

Decay heat removal with natural circulation is to be introduced to the LMFBR operation under loss of the electric power supply. The natural circulation is highly reliable, but the phenomenon is essentially unstable and subtle, which makes fine prediction difficult. The difficulties of experimental prediction are explained by facts that the phenomena are ruled by the delicate balance between the buoyancy force and the low pressure loss and are influenced by the various parameters such as local geometry, heat capacity and so on. Therefore the similarity rule for the natural circulation has not been fully understood. This study has been conducted to establish the simulation method for the natural circulation phenomena and the detailed phenomena have been reviewed. For the natural circulation in an LMFBR plant, there are no readily available reference velocity and temperature. These values are related only with the heating and cooling rate, the characteristic length and physical properties of the testing fluid. Basic equations were transformed by these values, and dimensionless equations were derived and then two dimensionless numbers, the Gr' number and the Bo' number, were identified. In order to examine the similarity rule for natural circulation we performed experiments using the different scale water models, a 1/20th and a 1/6th model. The temperatures and velocities at typical points were measured in the transient condition with various heating rate as a parameter. Measured temperatures and velocities were transformed to dimensionless forms for comparison and the effects of the Bo' number and the Gr' number were examined. As a result, it was clarified that the effect of the Gr' number is negligibly small but the effect of Bo' number still remained in our experimental range. The Bo' number of an actual plant is within the range of this experiment. Accordingly similitude of the Bo' number becomes important in an experiment to simulate an actual plant. (author)

Performance improvement of the Annular Core Pulse Reactor for reactor safety experiments

International Nuclear Information System (INIS)

Reuscher, J.A.; Pickard, P.S.

1976-01-01

The Annular Core Pulse Reactor (ACPR) is a TRIGA type reactor which has been in operation at Sandia Laboratories since 1967. The reactor is utilized in a wide variety of experimental programs which include radiation effects, neutron radiography, activation analysis, and fast reactor safety. During the past several years, the ACPR has become an important experimental facility for the United States Fast Reactor Safety Research Program and questions of interest to the safety of the LMFBR are being addressed. In order to enhance the capabilities of the ACPR for reactor safety experiments, a project to improve the performance of the reactor was initiated. It is anticipated that the pulse fluence can be increased by a factor of 2.0 to 2.5 utilizing a two-region core concept with high heat capacity fuel elements around the central irradiation cavity. In addition, the steady-state power of the reactor will be increased by about a factor of two. The new features of the improvements are described

Validation of turbulence models for LMFBR outlet plenum flows

International Nuclear Information System (INIS)

Chen, Y.B.; Golay, M.W.

1977-01-01

Small scale experiments involving water flows are used to provide mean flow and turbulence field data for LMFBR outlet plenum flows. Measurements are performed at Reynolds number (Re) values of 33000 and 70000 in a 1/15 - scale FFTF geometry and at Re = 35000 in a 3/80-scale CRBR geometry. The experimental behavior is predicted using two different two-equation turbulence model computer programs, TEACH-T and VARR-II. It is found that the qualitative nature of the flow field within the plenum depends strongly upon the distribution of the mean inlet flow field, importantly also upon the degree of inlet turbulence, and also upon the turbulent momentum exchange model used in the calculations. In the FFTF geometry, the TEACH-T predictions agree well with the experiments. 7 refs

Wire-wrapped rod-bundle heat-transfer analysis for LMFBR

International Nuclear Information System (INIS)

Wong, C.N.C.; Todreas, N.E.

1982-07-01

Helical wire wraps are widely used in the LMFBR fuel and blanket assemblies to provide coolant mixing and maintain proper spacing between fuel pins. The presence of the helical wire, however, may possibly induce heat transfer problems, such as the uncertainty of the maximum clad temperature as a result of the contact between the wires and the pins. In this study, the detailed transient three dimensional velocity and temperature distributions for the coolant around the pin will be determined by solving the governing momentum and energy equation numerically. A computer code HEATRAN has been developed to perform this calculation. Before the computer code HEATRAN is applied to the wire wrapped rod bundle problem, it is used to analyze a wide range of fluid and heat transfer problem to verify its capabilities

Analysis of structural heterogeneities on drilled cores: a reservoir modeling oriented methodology; Analyse des heterogeneites structurales sur carottes: une methodologie axee vers la modelisation des reservoirs

Energy Technology Data Exchange (ETDEWEB)

Cortes, P.; Petit, J.P. [Montpellier-2 Univ., Lab. de Geophysique, Tectonique et Sedimentologie, UMR CNRS 5573, 34 (France); Guy, L. [ELF Aquitaine Production, 64 - Pau (France); Thiry-Bastien, Ph. [Lyon-1 Univ., 69 (France)

1999-07-01

The characterization of structural heterogeneities of reservoirs is of prime importance for hydrocarbons recovery. A methodology is presented which allows to compare the dynamic behaviour of fractured reservoirs and the observation of microstructures on drilled cores or surface reservoir analogues. (J.S.)

Computational Hydrodynamics: How Portable and Scalable Are Heterogeneous Programming Paradigms?

DEFF Research Database (Denmark)

Pawlak, Wojciech; Glimberg, Stefan Lemvig; Engsig-Karup, Allan Peter

New many-core era applications at the interface of mathematics and computer science adopt modern parallel programming paradigms and expose parallelism through proper algorithms. We present new performance results for a novel massively parallel free surface wave model suitable for advanced......-device system sizes from desktops to large HPC systems such as superclusters and in the cloud utilizing heterogeneous devices like multi-core CPUs, GPUs, and Xeon Phi coprocessors. The numerical efficiency is evaluated on heterogeneous devices like multi-core CPUs, GPUs and Xeon Phi coprocessors to test...

Intelligent type sodium instrumentations for LMFBR

International Nuclear Information System (INIS)

Chen Daolong

1996-07-01

The constructions and performances of lots of newly developed intelligent type sodium instrumentations are described. The graduation characteristic equations for corresponding transducer using the medium temperature as the parameter are given. These intelligent type sodium instrumentations are possessed of good linearity. The accurate measurement data of sodium process parameters (flowrate, pressure and level) can be obtained by means of their on-line compensation function of the temperature effect. Moreover, these intelligent type sodium instrumentations are possessed of the self-inspection, the electric shutoff protection, the setting of full-scale, the setting of alarm limits (two upper limits and two lower limits alarms), the thermocouple breaking alarm, mutual isolative the 0∼10 V direct-current analogue output and the CENTRONICS standard digital output, and the alarm relay contact output. Theses intelligent type sodium instrumentations are suitable particularly for the instrument, control and protective systems of LMFBR by means of these excellent functions based on microprocessor. The basic errors of the intelligent type sodium flowmeter, immersed sodium flowmeter, sodium manometer and sodium level gauge are +-2%, +-2.3%, +-0.3% and +-1.9% of measuring ranges respectively. (9 figs.)

Analytical treatment of large leak pressure behavior in LMFBR steam generators

International Nuclear Information System (INIS)

Hori, Masao; Miyake, Osamu

1980-07-01

Simplified analytical methods applicable to the estimation of initial pressure spike in case of a large leak accident in LMFBR steam generators were devised as follows; (i) Estimation of the initial water leak rate by the centered rarefaction wave method, (ii) Estimation of the initial pressure spike by the one-dimensional compressible method with either the columnar bubble growth model or the spherical bubble growth model. These methods were compared with relevant experimental data or other more elaborate analyses and validated to be usable in simple geometry and limited time span cases. Application of these methods to an actual steam generator case was explained and demonstrated. (author)

Transference of advanced LMFBR control technology to the aerospace power system program

International Nuclear Information System (INIS)

Chisholm, G.H.

1984-01-01

Much recent R and D has been devoted to the safety of liquid metal fast breeder reactors (LMFBR's). Part of the resulting technology, especially advanced control systems, appears to be directly transferable to the space nuclear power program. Some of the ideas described herein have been already culminated in successful products that are available for application, e.g. analytical redundancy and fault-tolerant computers. Others, in various stages of R and D, are being developed as elements to support the design goals outlined in the following section, e.g. automated software verification, automated hardware verification, and system validation

1982 annual status report: reactor safety

International Nuclear Information System (INIS)

1982-01-01

This report presents the projects of the Reactor Safety Program at the JRC: 1) Reliability and risk evolution; 2) LWR loss of coolant accident studies; 3) Primary system integrity; 4) LMFBR core accident initiation and transition phase; and, 5) LMFBR accident post disassembly phase

O4.04‘FROM THE CORE TO BEYOND THE MARGIN’: A GENOMIC PICTURE OF GLIOBLASTOMA INTRATUMOR HETEROGENEITY

Science.gov (United States)

Aubry, M.; de Tayrac, M.; Etcheverry, A.; Clavreul, A.; Saikali, S.; Menei, P.; Mosser, J.

2014-01-01

INTRODUCTION: Glioblastoma (GB) is a very agressive brain tumor that almost systematically recurs. This recurrence is linked to the highly invasive behavior of this tumor. Major challenges in therapy of GB are therefore associated with controlling this infiltration sustained by a strong heterogeneous biology of GB tumors. In the past decade, molecular studies of GB have been focused on inter-individual heterogeneity. These studies have identified gene mutations and molecular signatures with putative prognostic or predictive significance. However, accumulating evidence suggests that intratumor heterogeneity is the key to understanding treatment failure. MATERIAL AND METHOD: To explore GB intratumor heterogeneity we developed a surgical multisampling scheme to collect tumor fragments from 10 GB patients in four spatially distinct areas defined on 3D MRI ‘from the core to beyond the margin’: necrotic zone, tumor zone, interface, and peripheral brain zone. These samples were studied genome-wide at three molecular levels: genome, transcriptome and methylome. We used Principal Component Analysis (PCA) to classify the samples and to select genes. We constructed a co-expression network on the basis of the expression data of the most informative genes related to the data structure revealed by PCA. RESULTS AND DISCUSSION: At the genome level, we identified common GB alterations (loss/partial loss of chromosome 10, polysomy of chromosome 7, focal deletion of the CDKN2A/B and focal high-level amplifications of EGFR) and a strong inter-individual molecular heterogeneity. Transcriptome analysis highlighted a pronounced intratumor architecture reflecting the surgical sampling plan of the study and identified gene modules associated with hallmarks of cancer. We provide a master gene signature highly correlated with the intratumor gradient and associated with the tumor infiltrative behavior. In this signature, the percentage of genes presenting an anti-correlation between

Trip report: United States LMFBR Steam Generator Team. IAEA symposium, Bensberg, Germany, October 14--17, 1974

International Nuclear Information System (INIS)

1974-01-01

Information is presented concerning steam generator design characteristics for the AFR reactor, SNR reactor, PHENIX reactor, SUPER PHENIX reactor, MONJU reactor, and BN-350 reactor; steam generator development programs for West Germany, France, Japan, U. K., and the U. S. S. R.; and the fabrication and inspection of steam generator components. Steam generator performance and maintenance requirements for operating LMFBR reactors are reviewed. (U.S.)

Compatibility of niobium, titanium, and vanadium metals with LMFBR cladding

International Nuclear Information System (INIS)

Wilson, C.N.

1975-10-01

A series of laboratory capsule annealing experiments were conducted to assess the compatibility of niobium, vanadium, and titanium with 316 stainless steel cladding in the temperature range of 700 to 800 0 C. Niobium, vanadium, and titanium are cantidate oxygen absorber materials for control of oxygen chemistry in LMFBR fuel pins. Capsule examination indicated good compatibility between niobium and 316 stainless steel at 800 0 C. Potential compatibility problems between cladding and vanadium or titanium were indicated at 800 0 C under reducing conditions. In the presence of Pu/sub 0.25/U/sub 0.75/O/sub 1.98/ fuel (Δanti G 02 congruent to -160 kcal/mole) no reaction was observed between vanadium or titanium and cladding at 800 0 C

Composition heterogeneity analysis for DUPIC fuel(I) - Statistical analysis

Energy Technology Data Exchange (ETDEWEB)

Choi, Hang Bok [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-08-01

The fuel composition heterogeneity effect on reactor performance parameters was assessed by refueling simulations for three DUPIC fuel options of fuel composition heterogeneity control: the fissile content adjustment, the reactivity control by slightly enriched and depleted uranium, and the reactivity control by natural uranium. For each DUPIC fuel option, the simulations were performed using 30 heterogeneous fuel types which were determined by the agglomerative hierarchical clustering method. The heterogeneity effect was considered during the refueling simulation by randomly selecting fuel types for the refueling operation. The refueling simulations of the heterogeneous core have shown that the key performance parameters such as the maximum channel power (MCP), maximum bundle power (MBP), and channel power peaking factor (CPPF) are close to those of the core that has single fuel type. For the three DUPIC fuel options, the uncertainties of MCP, MBP, and CPPF due to the fuel composition heterogeneity are less than 0.6, 1.5 and 0.8%, respectively, including the uncertainty of the group-average fuel property. This study has shown that the three DUPIC fuel options reduces the composition heterogeneity effectively and the zone power control system has a sufficient margin to adjust the perturbations cased by the fuel composition heterogeneity. 15 refs., 28 figs.,10 tabs. (Author)

Evaluation of high-pressure containment buildings for LMFBR's

International Nuclear Information System (INIS)

Armstrong, G.R.

1981-01-01

A study was conducted on the use of High Pressure LMFBR Containment Buildings for 1000 MW(e) LMFBRs. Two principal aspects were investigated: accident consequence mitigation and cost. Two types of hypothetical accidents were analyzed to establish consequence mitigation: melt-through and energetic expulsion. Three Containment Building (CB) design pressures were investigated: 69 kPa (10 psig), 207 kPa (30 psig), and 414 kPa (60 psig). Four types of design structures were analyzed to establish cost: steel, steel with confinement building, reinforced concrete, and prestressed/post-tensioned concrete. Results show that: it is within reason that a high pressure containment for a 1000 MW(e) reactor can be fabricated that will retain its integrity during postulated severe hypothetical accidents, if available measures are taken to reduce or prevent hydrogen production and the cost differential between basic high (414 kPa) and low (69 kPa) pressure containments is $10 x 10 6 or less

Residual stress effects in LMFBR fracture assessment procedures

International Nuclear Information System (INIS)

Hooton, D.G.

1984-01-01

Two post-yield fracture mechanics methods, which have been developed into fully detailed failure assessment procedures for ferritic structures, have been reviewed from the point of view of the manner in which as-welded residual stress effects are incorporated, and comparisons then made with finite element and theoretical models of centre-cracked plates containing residual/thermal stresses in the form of crack-driving force curves. Applying the procedures to austenitic structures, comparisons are made in terms of failure assessment curves and it is recommended that the preferred method for the prediction of critical crack sizes in LMFBR austenitic structures containing as-welded residual stresses is the CEGB-R6 procedure based on a flow stress defined at 3% strain in the parent plate. When the prediction of failure loads in such structures is required, it is suggested that the CEGB-R6 procedure be used with residual/thermal stresses factored to give a maximum total stress of flow stress magnitude

Heterogeneous Recycle of Transuranics Fuels in Fast Reactors

International Nuclear Information System (INIS)

Hoffman, Edward; Taiwo, Temitope; Hill, Robert

2008-01-01

A preliminary physics evaluation of the impacts of heterogeneous recycle using Pu+Np driver and minor actinide target fuel assemblies in fast reactor cores has been performed by comparing results to those obtained for a reference homogeneous recycle core using driver assemblies containing grouped transuranic (TRU) fuel. Parametric studies are performed on the reference heterogeneous recycle core to evaluate the impacts of variations in the pre- and post-separation cooling times, target material type (uranium and non-uranium based), target amount and location, and other parameters on the system performance. This study focused on startup, single-pass cores for the purpose of quantifying impacts and also included comparisons to the option of simply storing the LWR spent nuclear fuel over a 50-year period. An evaluation of homogeneous recycle cores with elevated minor actinide contents is presented to illustrate the impact of using progressively higher TRU content on the core and transmutation performance, as a means of starting with known fuel technology with the aim of ultimately employing grouped TRU fuel in such cores. Reactivity coefficients and safety parameters are presented to indicate that the cores evaluated appear workable from a safety perspective, though more detailed safety and systems evaluations are required. (authors)

TRIO a general computer code for reactor 3-D flows analysis. Application to a LMFBR hot plenum

International Nuclear Information System (INIS)

Magnaud, J.P.; Rouzaud, P.

1985-09-01

TRIO is a code developed at CEA to investigate general incompressible 2D and 3D viscous flows. Two calculations are presented: the lid driven cubic cavity at Re=400; steady state (velocity and temperature field) of a LMFBR hot plenum, carried out in order to prepare the calculation of a cold shock consecutive to a reactor scram. 8 refs., 26 figs.

An Innovative Three-Dimensional Heterogeneous Coarse-Mesh Transport Method for Advanced and Generation IV Reactor Core Analysis and Design

International Nuclear Information System (INIS)

Rahnema, Farzad

2009-01-01

This project has resulted in a highly efficient method that has been shown to provide accurate solutions to a variety of 2D and 3D reactor problems. The goal of this project was to develop (1) an accurate and efficient three-dimensional whole-core neutronics method with the following features: based solely on transport theory, does not require the use of cross-section homogenization, contains a highly accurate and self-consistent global flux reconstruction procedure, and is applicable to large, heterogeneous reactor models, and to (2) create new numerical benchmark problems for code cross-comparison.

Measurement and analysis of neutron flux distribution of STACY heterogeneous core by position sensitive proportional counter. Contract research

Energy Technology Data Exchange (ETDEWEB)

Murazaki, Minoru; Uno, Yuichi; Miyoshi, Yoshinori [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

We have measured neutron flux distribution around the core tank of STACY heterogeneous core by position sensitive proportional counter (PSPC) to develop the method to measure reactivity for subcritical systems. The neutron flux distribution data in the position accuracy of {+-}13 mm have been obtained in the range of uranium concentration of 50g/L to 210g/L both in critical and in subcritical state. The prompt neutron decay constant, {alpha}, was evaluated from the measurement data of pulsed neutron source experiments. We also calculated distribution of neutron flux and {sup 3}He reaction rates at the location of PSPC by using continuous energy Monte Carlo code MCNP. The measurement data was compared with the calculation results. As results of comparison, calculated values agreed generally with measurement data of PSPC with Cd cover in the region above half of solution height, but the difference between calculated value and measurement data was large in the region below half of solution height. On the other hand, calculated value agreed well with measurement data of PSPC without Cd cover. (author)

Structural consideration for hot and cold pipe clamps in LMFBR applications

International Nuclear Information System (INIS)

Anderson, M.J.; Huang, S.N.; Kappauf, H.; Wagner, S.E.; Wirtz, K.H.

1983-01-01

A series of analytical studies are described which evaluate stress levels induced in a 600 mm high temperature, thin-wall sodium pipeline by two alternate clamp designs. The first design consists of a band mounted directly on the pipe and is called the hot clamp. The second design consists of a band mounted using insulation standoffs and is called the cold clamp. Pipe stress levels induced by transient thermal dead weight and seismic loads are discussed. Pipe stress levels and system dynamic spring rates are presented. Procedures utilized to combine clamp induced pipe stress with other short and long term pipe system stresses are detailed. Recommendations for practical application in LMFBR pipe systems are made

Structural considerations for hot and cold pipe clamps in LMFBR applications

International Nuclear Information System (INIS)

Anderson, M.J.; Huang, S.N.; Wagner, S.E.; Kappauf, H.; Wirtz, K.H.

1983-01-01

A series of analytical studies are described which evaluate stress levels induced in a 600 mm high temperature, thin-wall sodium pipeline by two alternate clamp designs. The first design consists of a band mounted directly on the pipe and is called the hot clamp. The second design consists of a band mounted using insulation standoffs and is called the cold clamp. Pipe stress levels induced by transient thermal dead weight and seismic loads are discussed. Pipe stress levels and system dynamic spring rates are presented. Procedures utilized to combine clamp induced pipe stress with other short and long term pipe system stresses are detailed. Recommendations for practical application in LMFBR pipe systems are made

Advanced LMFBR fuel cladding susceptability to stress corrosion due to reprocessing impurities

International Nuclear Information System (INIS)

Henslee, S.P.

1987-03-01

The potential degradation of LMFBR fuel cladding alloys by chlorides, when used in metallic fuel systems, was evaluated. The alloys tested were D-9 and HT-9 stainless steels, austenitic and ferritic alloys respectively. These two alloys were tested in parallel with and their performance compared to the austenitic stainless steel Type 316. All alloys were tested for 7400 hours in a stress rupture environment with chloride exposure at either 550/degree/C 650/degree/C. None of the alloys tested were found to exhibit any degradation in time-to-rupture by the presence of chlorides under the conditions imposed during testing. 8 refs., 4 figs., 2 tabs

Wave propagation simulation in the upper core of sodium-cooled fast reactors using a spectral-element method for heterogeneous media

Science.gov (United States)

Nagaso, Masaru; Komatitsch, Dimitri; Moysan, Joseph; Lhuillier, Christian

2018-01-01

ASTRID project, French sodium cooled nuclear reactor of 4th generation, is under development at the moment by Alternative Energies and Atomic Energy Commission (CEA). In this project, development of monitoring techniques for a nuclear reactor during operation are identified as a measure issue for enlarging the plant safety. Use of ultrasonic measurement techniques (e.g. thermometry, visualization of internal objects) are regarded as powerful inspection tools of sodium cooled fast reactors (SFR) including ASTRID due to opacity of liquid sodium. In side of a sodium cooling circuit, heterogeneity of medium occurs because of complex flow state especially in its operation and then the effects of this heterogeneity on an acoustic propagation is not negligible. Thus, it is necessary to carry out verification experiments for developments of component technologies, while such kind of experiments using liquid sodium may be relatively large-scale experiments. This is why numerical simulation methods are essential for preceding real experiments or filling up the limited number of experimental results. Though various numerical methods have been applied for a wave propagation in liquid sodium, we still do not have a method for verifying on three-dimensional heterogeneity. Moreover, in side of a reactor core being a complex acousto-elastic coupled region, it has also been difficult to simulate such problems with conventional methods. The objective of this study is to solve these 2 points by applying three-dimensional spectral element method. In this paper, our initial results on three-dimensional simulation study on heterogeneous medium (the first point) are shown. For heterogeneity of liquid sodium to be considered, four-dimensional temperature field (three spatial and one temporal dimension) calculated by computational fluid dynamics (CFD) with Large-Eddy Simulation was applied instead of using conventional method (i.e. Gaussian Random field). This three-dimensional numerical

How to program 122,400 heterogeneous cores and retain your sanity

International Nuclear Information System (INIS)

Patkin, Scott

2010-01-01

Current technology trends favor hybrid architectures, typically with each node in a cluster containing both general-purpose and specialized 'accelerator' processors. The typical model for programming such systems is host-centric: The general-purpose processor orchestrates the computation, offloading performance-critical work to the accelerator, and data is communicated only among general-purpose processors. In this talk we propose a radically different hybrid-programming approach, which we call the 'reverse-acceleration model'. In this model the accelerators orchestrate the computation, offloading unacceleratable work to the general-purpose processors. Data is communicated among accelerators, not among general-purpose processors. We present the Cell Messaging Layer (CML), an implementation of the reverse-acceleration model for Los Alamos National Laboratory's Roadrunner supercomputer, a complex conglomerate of 122,400 processor cores of various types, multiple memory domains, and multiple network types, all with radically different performance characteristics but which together make Roadrunner the world's second-fastest supercomputer. CML demonstrates a new messaging-layer implementation technique called 'receiver-initiated message passing', which reduces communication latency by up to a third. Our thesis is that the reverse-acceleration model simplifies porting codes to heterogeneous systems and facilitates performance optimization. We present a case study of a legacy neutron-transport code that we modified to use reverse acceleration. Performance results from running this code across the full Roadrunner system indicate a substantial performance improvement over the unaccelerated version of the code.

Spatial connectivity in a highly heterogeneous aquifer: From cores to preferential flow paths

Science.gov (United States)

Bianchi, M.; Zheng, C.; Wilson, C.; Tick, G.R.; Liu, Gaisheng; Gorelick, S.M.

2011-01-01

This study investigates connectivity in a small portion of the extremely heterogeneous aquifer at the Macrodispersion Experiment (MADE) site in Columbus, Mississippi. A total of 19 fully penetrating soil cores were collected from a rectangular grid of 4 m by 4 m. Detailed grain size analysis was performed on 5 cm segments of each core, yielding 1740 hydraulic conductivity (K) estimates. Three different geostatistical simulation methods were used to generate 3-D conditional realizations of the K field for the sampled block. Particle tracking calculations showed that the fastest particles, as represented by the first 5% to arrive, converge along preferential flow paths and exit the model domain within preferred areas. These 5% fastest flow paths accounted for about 40% of the flow. The distribution of preferential flow paths and particle exit locations is clearly influenced by the occurrence of clusters formed by interconnected cells with K equal to or greater than the 0.9 decile of the data distribution (10% of the volume). The fraction of particle paths within the high-K clusters ranges from 43% to 69%. In variogram-based K fields, some of the fastest paths are through media with lower K values, suggesting that transport connectivity may not require fully connected zones of relatively homogenous K. The high degree of flow and transport connectivity was confirmed by the values of two groups of connectivity indicators. In particular, the ratio between effective and geometric mean K (on average, about 2) and the ratio between the average arrival time and the arrival time of the fastest particles (on average, about 9) are consistent with flow and advective transport behavior characterized by channeling along preferential flow paths. ?? 2011 by the American Geophysical Union.

Quantifying spatial heterogeneity from images

International Nuclear Information System (INIS)

Pomerantz, Andrew E; Song Yiqiao

2008-01-01

Visualization techniques are extremely useful for characterizing natural materials with complex spatial structure. Although many powerful imaging modalities exist, simple display of the images often does not convey the underlying spatial structure. Instead, quantitative image analysis can extract the most important features of the imaged object in a manner that is easier to comprehend and to compare from sample to sample. This paper describes the formulation of the heterogeneity spectrum to show the extent of spatial heterogeneity as a function of length scale for all length scales to which a particular measurement is sensitive. This technique is especially relevant for describing materials that simultaneously present spatial heterogeneity at multiple length scales. In this paper, the heterogeneity spectrum is applied for the first time to images from optical microscopy. The spectrum is measured for thin section images of complex carbonate rock cores showing heterogeneity at several length scales in the range 10-10 000 μm.

Research and development of bellows for LMFBR in Japan

International Nuclear Information System (INIS)

Takahashi, T.; Mukai, K.; Yamamoto, K.

1980-01-01

Bellows are employed as useful mechanical elements with their flexibility and imperviousness to liquid and gas in the system in which such chemically active substances as sodium are handled. Since the early time of development of Japanese LMFBR, bellows have been used e.g. for the shaft seal of small sodium valves. Bellows are employed in the fast experimental reactor JOYO which is now in operation and the fast prototype reactor MONJU whose design program is in final stage at the following parts: control rod drive mechanism; intermediate heat exchanger; small valve; mechanical penetration assembly of the containment boundary; outer piping of the double-walled primary system (for JOYO only). In addition, the application of bellows as thermal expansion joint to the main piping system is under consideration for future FBRs. This paper outlines the research and development work on bellows for FBR use in Japan. (author)

Research and development of bellows for LMFBR in Japan

International Nuclear Information System (INIS)

Takahashi, Tadao; Mukai, Kazuo; Yamamoto, Ken.

1979-11-01

The bellows is employed as a useful mechanical element with its flexibility and imperviousness to liquid and gas in the system in which such chemically active substance as sodium is handled. Since the early time of development of Japanese LMFBR, bellows have been used e.g. for the shaft seal of small sodium valves. Bellows are employed in the fast experimental reactor JOYO which is now in operation and the fast prototype reactor MONJU whose design program is in final stage at the following parts: - control rod drive mechanism, - intermediate heat exchanger, - small valve, - mechanical penetration assembly of the containment boundary, - outer piping of the double-walled primary system (for JOYO only). In addition, the application of bellows as thermal expansion joint to the main piping system is under consideration for future FBRs. This paper outlines the research and development work on bellows for the FBR use in Japan. (author)

Probabilistic assessment of critically flawed LMFBR PHTS piping elbows

International Nuclear Information System (INIS)

Balkey, K.R.; Wallace, I.T.; Vaurio, J.K.

1982-01-01

One of the important functions of the Primary Heat Transport System (PHTS) of a large Liquid Metal Fast Breeder Reactor (LMFBR) plant is to contain the circulating radioactive sodium in components and piping routed through inerted areas within the containment building. A significant possible failure mode of this vital system is the development of cracks in the piping components. This paper presents results from the probabilistic assessment of postulated flaws in the most-critical piping elbow of each piping leg. The criticality of calculated maximum sized flaws is assessed against an estimated material fracture toughness to determine safety factors and failure probability estimates using stress-strength interference theory. Subsequently, a different approach is also employed in which the randomness of the initial flaw size and loading are more-rigorously taken into account. This latter approach yields much smaller probability of failure values when compared to the stress-strength interference analysis results

Parallelizing Compiler Framework and API for Power Reduction and Software Productivity of Real-Time Heterogeneous Multicores

Science.gov (United States)

Hayashi, Akihiro; Wada, Yasutaka; Watanabe, Takeshi; Sekiguchi, Takeshi; Mase, Masayoshi; Shirako, Jun; Kimura, Keiji; Kasahara, Hironori

Heterogeneous multicores have been attracting much attention to attain high performance keeping power consumption low in wide spread of areas. However, heterogeneous multicores force programmers very difficult programming. The long application program development period lowers product competitiveness. In order to overcome such a situation, this paper proposes a compilation framework which bridges a gap between programmers and heterogeneous multicores. In particular, this paper describes the compilation framework based on OSCAR compiler. It realizes coarse grain task parallel processing, data transfer using a DMA controller, power reduction control from user programs with DVFS and clock gating on various heterogeneous multicores from different vendors. This paper also evaluates processing performance and the power reduction by the proposed framework on a newly developed 15 core heterogeneous multicore chip named RP-X integrating 8 general purpose processor cores and 3 types of accelerator cores which was developed by Renesas Electronics, Hitachi, Tokyo Institute of Technology and Waseda University. The framework attains speedups up to 32x for an optical flow program with eight general purpose processor cores and four DRP(Dynamically Reconfigurable Processor) accelerator cores against sequential execution by a single processor core and 80% of power reduction for the real-time AAC encoding.

The role of high temperature heterogeneous reaction kinetics in the rate of radionuclide vaporisation during core-concrete interactions

International Nuclear Information System (INIS)

Raymond, D.P.; Clough, P.N.

1989-09-01

Heterogeneous reactions may cause enhanced release of radionuclides during the core-concrete interaction (CCl) stage of a PWR severe accident. The VANESA computer code models these CCI releases using chemical equilibrium assumptions; however, the possibility that chemical kinetics could prevent equilibrium from being achieved is considered in this report. Direct experimental evidence is lacking on these reactions. Therefore, some analogues studies are reviewed, including examples of Eyring's surface reaction rate theory; sequential vaporisation-oxidation processes; iron and steelmaking chemistry; radionuclide evaporation from solid UO 2 . This circumstantial evidence appeared to agree with the current assumptions, in VANESA and some UK modelling studies, that mass transfer, rather than chemical kinetics will limit the rate at which equilibrium is attained. (author)

HIGH TEMPERATURE, HIGH POWER HETEROGENEOUS NUCLEAR REACTOR

Science.gov (United States)

Hammond, R.P.; Wykoff, W.R.; Busey, H.M.

1960-06-14

A heterogeneous nuclear reactor is designed comprising a stationary housing and a rotatable annular core being supported for rotation about a vertical axis in the housing, the core containing a plurality of radial fuel- element supporting channels, the cylindrical empty space along the axis of the core providing a central plenum for the disposal of spent fuel elements, the core cross section outer periphery being vertically gradated in radius one end from the other to provide a coolant duct between the core and the housing, and means for inserting fresh fuel elements in the supporting channels under pressure and while the reactor is in operation.

Heterogeneous composite bodies with isolated lenticular shaped cermet regions

Science.gov (United States)

Sherman, Andrew J [Cirtland Hills, OH

2009-12-22

A heterogeneous body having ceramic rich cermet regions in a more ductile metal matrix. The heterogeneous bodies are formed by thermal spray operations on metal substrates. The thermal spray operations apply heat to a cermet powder and project it onto a solid substrate. The cermet powder is composed of complex composite particles in which a complex ceramic-metallic core particle is coated with a matrix precursor. The cermet regions are generally comprised of complex ceramic-metallic composites that correspond approximately to the core particles. The cermet regions are approximately lenticular shaped with an average width that is at least approximately twice the average thickness. The cermet regions are imbedded within the matrix phase and generally isolated from one another. They have obverse and reverse surfaces. The matrix phase is formed from the matrix precursor coating on the core particles. The amount of heat applied during the formation of the heterogeneous body is controlled so that the core particles soften but do not become so fluid that they disperse throughout the matrix phase. The force of the impact on the surface of the substrate tends to flatten them. The flattened cermet regions tend to be approximately aligned with one another in the body.

BN-600 hybrid core benchmark analyses

International Nuclear Information System (INIS)

Kim, Y.I.; Stanculescu, A.; Finck, P.; Hill, R.N.; Grimm, K.N.

2003-01-01

Benchmark analyses for the hybrid BN-600 reactor that contains three uranium enrichment zones and one plutonium zone in the core, have been performed within the frame of an IAEA sponsored Coordinated Research Project. The results for several relevant reactivity parameters obtained by the participants with their own state-of-the-art basic data and codes, were compared in terms of calculational uncertainty, and their effects on the ULOF transient behavior of the hybrid BN-600 core were evaluated. The comparison of the diffusion and transport results obtained for the homogeneous representation generally shows good agreement for most parameters between the RZ and HEX-Z models. The burnup effect and the heterogeneity effect on most reactivity parameters also show good agreement for the HEX-Z diffusion and transport theory results. A large difference noticed for the sodium and steel density coefficients is mainly due to differences in the spatial coefficient predictions for non fuelled regions. The burnup reactivity loss was evaluated to be 0.025 (4.3 $) within ∼ 5.0% standard deviation. The heterogeneity effect on most reactivity coefficients was estimated to be small. The heterogeneity treatment reduced the control rod worth by 2.3%. The heterogeneity effect on the k-eff and control rod worth appeared to differ strongly depending on the heterogeneity treatment method. A substantial spread noticed for several reactivity coefficients did not give a significant impact on the transient behavior prediction. This result is attributable to compensating effects between several reactivity effects and the specific design of the partially MOX fuelled hybrid core. (author)

VENUS-2, Reactor Kinetics with Feedback, 2-D LMFBR Disassembly Excursions

International Nuclear Information System (INIS)

Jackson, J.F.; Nicholson, R.B.; Weber, D.P.

1980-01-01

1 - Description of problem or function: VENUS-2 is an improved edition of the VENUS fast-reactor disassembly program. It is a two- dimensional (r-z) coupled neutronics-hydrodynamics code that calculates the dynamic behavior of an LMFBR during a prompt-critical disassembly excursion. It calculates the power history and fission energy release as well as the space-time histories of the fuel temperatures, core material pressures, and core material motions. Reactivity feedback effects due to Doppler broadening and reactor material motion are taken into account. 2 - Method of solution: The power and energy release are calculated using a point-kinetics formulation with up to six delayed neutron groups. The reactivity is a combination of an input driving function and feedback effects due to Doppler broadening and material motion. An adiabatic model is used to calculate the temperature increase throughout the reactor based on an initial temperature distribution and power profile provided as input data. These temperatures are, in turn, converted to fuel pressures through one of several equation of state options provided. The material motion that results from the pressure buildup is calculated by a direct finite difference solution of a set of two-dimensional (r-z) hydrodynamics equations. This is done in Lagrangian coordinates. The reactivity change associated with this motion is calculated by first-order perturbation theory. The displacements are also used to adjust the fuel densities as required for the density dependent equation-of- state option. An automatic time-step-size selection scheme is provided. 3 - Restrictions on the complexity of the problem: VENUS-2 is written so that the dimensions of the storage arrays can be readily changed to accommodate a broad range of problem sizes. In the base version, the total number of mesh intervals is restricted such that (NR+3)*(NZ+3) is less than 700, where NR and NZ are the total number of mesh intervals in the r and z

Finite element elastic-plastic analysis of LMFBR components

International Nuclear Information System (INIS)

Levy, A.; Pifko, A.; Armen, H. Jr.

1978-01-01

The present effort involves the development of computationally efficient finite element methods for accurately predicting the isothermal elastic-plastic three-dimensional response of thick and thin shell structures subjected to mechanical and thermal loads. This work will be used as the basis for further development of analytical tools to be used to verify the structural integrity of liquid metal fast breeder reactor (LMFBR) components. The methods presented here have been implemented into the three-dimensional solid element module (HEX) of the Grumman PLANS finite element program. These methods include the use of optimal stress points as well as a variable number of stress points within an element. This allows monitoring the stress history at many points within an element and hence provides an accurate representation of the elastic-plastic boundary using a minimum number of degrees of freedom. Also included is an improved thermal stress analysis capability in which the temperature variation and corresponding thermal strain variation are represented by the same functional form as the displacement variation. Various problems are used to demonstrate these improved capabilities. (Auth.)

Two-dimensional steady-state thermal and hydraulic analysis code for prediction of detailed temperature fields around distorted fuel pin in LMFBR assembly: SPOTBOW

International Nuclear Information System (INIS)

Shimizu, T.

1983-01-01

SPOTBOW computer program has been developed for predicting detailed temperature and turbulent flow velocity fields around distorted fuel pins in LMFBR fuel assemblies, in which pin to pin and pin to wrapper tube contacts may occur. The present study started from the requirement of reactor core designers to evaluate local hot spot temperature due to the wire contact effect and the pin bowing effect on cladding temperature distribution. This code calculates for both unbaffled and wire-wrapped pin bundles. The Galerkin method and iterative procedure were used to solve the basic equations which govern the local heat and momentum transfer in turbulent fluid flow around the distorted pins. Comparisons have been made with cladding temperatures measured in normal and distorted pin bundle mockups to check the validity of this code. Predicted peak temperatures in the vicinity of wire contact point were somewhat higher than the measured values, and the shape of the peaks agreed well with measurement. The changes of cladding temperature due to the decrease of gap width between bowing pin and adjacent pin were predicted well

Gravitational agglomeration of post-HCDA LMFBR aerosols: nonspherical particles

International Nuclear Information System (INIS)

Tuttle, R.F.; Loyalka, S.K.

1982-12-01

Aerosol behavior analysis computer programs have shown that temporal aerosol size distributions in nuclear reactor containments are sensitive to shape factors. This research investigates shape factors by a detailed theoretical analysis of hydrodynamic interactions between a nonspherical particle and a spherical particle undergoing gravitational collisions in an LMFBR environment. First, basic definitions and expressions for settling speeds and collisional efficiencies of nonspherical particles are developed. These are then related to corresponding quantities for spherical particles through shape factors. Using volume equivalent diameter as the defining length in the gravitational collision kernel, the aerodynamic shape factor, the density correction factor, and the gravitational collision shape factor, are introduced to describe the collision kernel for collisions between aerosol agglomerates. The Navier-Stokes equation in oblate spheroidal coordinates is solved to model a nonspherical particle and then the dynamic equations for two particle motions are developed. A computer program (NGCEFF) is constructed, and the dynamical equations are solved by Gear's method

Irradiation effects on low-friction coatings for LMFBR applications

International Nuclear Information System (INIS)

Ward, A.L.; Johnson, R.N.; Guthrie, G.L.; Aungst, R.C.

1975-11-01

A variety of wear-resistant low-friction materials has been irradiated in the EBR-II in order to assess their reponse to LMFBR environments. Pre- and postirradiation testing and examination efforts have concentrated on candidate materials for application to the wear pads on FTR ducts (fuel, control, and reflector assemblies), and a significant result has been qualification of a proprietary detonation-gun-applied chromium carbide coating which employs a Ni Cr binder. Additional materials such as Inconel-718, Haynes-273, aluminides, and various chromium carbide/binder combinations, and other application processes such as plasma-spray, weld-overlays, diffusion bonding and explosive bonding, have also been studied. The most detailed examinations were conducted on selected chromium carbide coatings and included visual inspection, weight and dimensional measurements, metallography, electron microprobe, epoxy-lift-off, and x-ray diffraction analysis. Chromium carbide coatings applied by the detonation-gun process have demonstrated a marked superiority to those applied by plasma-spray techniques

Dynamical links between small- and large-scale mantle heterogeneity: Seismological evidence

Science.gov (United States)

Frost, Daniel A.; Garnero, Edward J.; Rost, Sebastian

2018-01-01

We identify PKP • PKP scattered waves (also known as P‧ •P‧) from earthquakes recorded at small-aperture seismic arrays at distances less than 65°. P‧ •P‧ energy travels as a PKP wave through the core, up into the mantle, then scatters back down through the core to the receiver as a second PKP. P‧ •P‧ waves are unique in that they allow scattering heterogeneities throughout the mantle to be imaged. We use array-processing methods to amplify low amplitude, coherent scattered energy signals and resolve their incoming direction. We deterministically map scattering heterogeneity locations from the core-mantle boundary to the surface. We use an extensive dataset with sensitivity to a large volume of the mantle and a location method allowing us to resolve and map more heterogeneities than have previously been possible, representing a significant increase in our understanding of small-scale structure within the mantle. Our results demonstrate that the distribution of scattering heterogeneities varies both radially and laterally. Scattering is most abundant in the uppermost and lowermost mantle, and a minimum in the mid-mantle, resembling the radial distribution of tomographically derived whole-mantle velocity heterogeneity. We investigate the spatial correlation of scattering heterogeneities with large-scale tomographic velocities, lateral velocity gradients, the locations of deep-seated hotspots and subducted slabs. In the lowermost 1500 km of the mantle, small-scale heterogeneities correlate with regions of low seismic velocity, high lateral seismic gradient, and proximity to hotspots. In the upper 1000 km of the mantle there is no significant correlation between scattering heterogeneity location and subducted slabs. Between 600 and 900 km depth, scattering heterogeneities are more common in the regions most remote from slabs, and close to hotspots. Scattering heterogeneities show an affinity for regions close to slabs within the upper 200 km of the

Structural dynamics in LMFBR containment analysis. A brief survey of computational methods and codes

International Nuclear Information System (INIS)

Chang, Y.W.

1977-01-01

This paper gives a brief survey of the computational methods and codes available for LMFBR containment analysis. The various numerical methods commonly used in the computer codes are compared. It provides the reactor engineers to up-to-date information on the development of structural dynamics in LMFBR containment analysis. It can also be used as a basis for the selection of the numerical method in the future code development. First, the commonly used finite-difference expressions in the Lagrangian codes will be compared. Sample calculations will be used as a basis for discussing and comparing the accuracy of the various finite-difference representations. The distortion of the meshes will also be compared; the techniques used for eliminating the numerical instabilities will be discussed and compared using examples. Next, the numerical methods used in the Eulerian formulation will be compared, first among themselves and then with the Lagrangian formulations. Special emphasis is placed on the effect of mass diffusion of the Eulerian calculation on the propagation of discontinuities. Implicit and explicit numerical integrations will be discussed and results obtained from these two techniques will be compared. Then, the finite-element methods are compared with the finite-difference methods. The advantages and disadvantages of the two methods will be discussed in detail, together with the versatility and ease of application of the method to containment analysis having complex geometries. It will also be shown that the finite-element equations for a constant-pressure fluid element is identical to the finite-difference equations using contour integrations. Finally, conclusions based on this study will be given

International Atomic Energy Agency specialist meeting on advances in structural analysis for LMFBR applications. Summary report

Energy Technology Data Exchange (ETDEWEB)

Perez, M A; Roche, R L [eds.

1983-05-01

After the first session on review of national positions in the subject field, the meeting was divided into five technical sections as follows: General methods of Structural Analysis for Elevated Temperatures; Inelastic Analysis Methods for Elevated Temperature; Effects of Cyclic loading; Design Codes and Criteria; Instability and Buckling - Piping Analysis in the Creep Range. The conclusions of the Meeting were summarised as follows. In view of the complexity of material behaviour and the variability of properties from cast to cast, continuing work is needed to develop simple constitutive relations which ensure an acceptable level of conservatism for design evaluations. It is recognized that simplified design methods require further development for the assessment of ratchetting and shakedown of high temperature structures. More development work is required in the areas of buckling elastic follow up weld factors and these developments should take account of the imperfections inherent in welded fabrications. There is a need for realistic tests on welded structural features to validate design methods. It is proposed that this subject would be the topic of a future specialists meeting. In several countries, organisations are now preparing Guides and Codes concerning Structural Assessment for LMFBR components. It seems that some of these Codes could be drafted within a few years. In order to make a more realistic assessment of LMFBR structures, defect assessment in elevated temperature range must be considered.

International Atomic Energy Agency specialist meeting on advances in structural analysis for LMFBR applications. Summary report

International Nuclear Information System (INIS)

Perez, M.A.; Roche, R.L.

1983-05-01

After the first session on review of national positions in the subject field, the meeting was divided into five technical sections as follows: General methods of Structural Analysis for Elevated Temperatures; Inelastic Analysis Methods for Elevated Temperature; Effects of Cyclic loading; Design Codes and Criteria; Instability and Buckling - Piping Analysis in the Creep Range. The conclusions of the Meeting were summarised as follows. In view of the complexity of material behaviour and the variability of properties from cast to cast, continuing work is needed to develop simple constitutive relations which ensure an acceptable level of conservatism for design evaluations. It is recognized that simplified design methods require further development for the assessment of ratchetting and shakedown of high temperature structures. More development work is required in the areas of buckling elastic follow up weld factors and these developments should take account of the imperfections inherent in welded fabrications. There is a need for realistic tests on welded structural features to validate design methods. It is proposed that this subject would be the topic of a future specialists meeting. In several countries, organisations are now preparing Guides and Codes concerning Structural Assessment for LMFBR components. It seems that some of these Codes could be drafted within a few years. In order to make a more realistic assessment of LMFBR structures, defect assessment in elevated temperature range must be considered

Advanced core-analyses for subsurface characterization

Science.gov (United States)

Pini, R.

2017-12-01

The heterogeneity of geological formations varies over a wide range of length scales and represents a major challenge for predicting the movement of fluids in the subsurface. Although they are inherently limited in the accessible length-scale, laboratory measurements on reservoir core samples still represent the only way to make direct observations on key transport properties. Yet, properties derived on these samples are of limited use and should be regarded as sample-specific (or `pseudos'), if the presence of sub-core scale heterogeneities is not accounted for in data processing and interpretation. The advent of imaging technology has significantly reshaped the landscape of so-called Special Core Analysis (SCAL) by providing unprecedented insight on rock structure and processes down to the scale of a single pore throat (i.e. the scale at which all reservoir processes operate). Accordingly, improved laboratory workflows are needed that make use of such wealth of information by e.g., referring to the internal structure of the sample and in-situ observations, to obtain accurate parameterisation of both rock- and flow-properties that can be used to populate numerical models. We report here on the development of such workflow for the study of solute mixing and dispersion during single- and multi-phase flows in heterogeneous porous systems through a unique combination of two complementary imaging techniques, namely X-ray Computed Tomography (CT) and Positron Emission Tomography (PET). The experimental protocol is applied to both synthetic and natural porous media, and it integrates (i) macroscopic observations (tracer effluent curves), (ii) sub-core scale parameterisation of rock heterogeneities (e.g., porosity, permeability and capillary pressure), and direct 3D observation of (iii) fluid saturation distribution and (iv) the dynamic spreading of the solute plumes. Suitable mathematical models are applied to reproduce experimental observations, including both 1D and 3D

Heterogeneous computing with OpenCL

CERN Document Server

2013-01-01

Heterogeneous Computing with OpenCL teaches OpenCL and parallel programming for complex systems that may include a variety of device architectures: multi-core CPUs, GPUs, and fully-integrated Accelerated Processing Units (APUs) such as AMD Fusion technology. Designed to work on multiple platforms and with wide industry support, OpenCL will help you more effectively program for a heterogeneous future. Written by leaders in the parallel computing and OpenCL communities, this book will give you hands-on OpenCL experience to address a range of fundamental parallel algorithms. The authors explore memory spaces, optimization techniques, graphics interoperability, extensions, and debugging and profiling. Intended to support a parallel programming course, Heterogeneous Computing with OpenCL includes detailed examples throughout, plus additional online exercises and other supporting materials.

Experimental investigation of flow dynamics in the SNR-upper-core structure

International Nuclear Information System (INIS)

Meyer, L.

1985-03-01

This report describes the results of a simulant-material experimental investigation of flow dynamics in the upper-core (UCS) during a HCDA of a LMFBR. The experiments were designed to verify some of the thermal-hydraulic models in SIMMER-II. Four different liquids were used to simulate the flashing U0 2 ; and numerous parameter variations were made regarding initial pressure, temperature, and configurations of the test apparatus. The experiments showed the large effect of the heat transfer in the UCS and the relatively small effect of friction. The reduction in final kinetic energy by the presence of the UCS is shown as a function of the initial pressure and the temperature difference between core and UCS. Calculations with SIMMER-II for the wide range of experiments produced results for the kinetic energy within a factor of 2 of the experimental results without changing the crucial input parameters. The minimum droplet size during the flashing process and the structure-side heat transfer coefficient were determined to be the crucial and most sensitive parameters. This reflects deficiencies in modeling of both the flashing process and the transient heat conduction in the structure. (orig./HP) [de

Coolant mixing in the LMFBR outlet plenum

International Nuclear Information System (INIS)

Chen, Y.B.; Golay, M.W.

1977-06-01

Small scale experiments involving water flows are used to provide mean flow and turbulence field data for LMFBR outlet plenum flows. Measurements are performed at Reynolds Number (Re) values of 33000 and 70000 in a 1/15-scale FFTF geometry and at Re = 35000 in a 3/80-scale CRBR geometry. The experimental behavior is predicted using two different turbulence model computer programs, TEACH-T and VARR-II. It is found that the qualitative nature of the flow field within the plenum depends strongly upon the distribution of the mean inlet velocity field, upon the degree of inlet turbulence, and upon the turbulence momentum exchange model used in the calculations. It is found in the FFTF geometry that the TEACH-T predictions are better than that of VARR-II, and in the CRBR geometry neither code provides a good prediction of the observed behavior. From the sensitivity analysis, it is found that the production and dissipation of turbulence are the dominant terms in the transport equations for turbulent kinetic energy and turbulent energy dissipation rate, and the diffusion terms are relatively small. From the same study a new set of empirical constants for the turbulence model is evolved for the prediction of plenum flows

CAT reconstruction and potting comparison of a LMFBR fuel bundle

International Nuclear Information System (INIS)

Betten, P.R.; Tow, D.M.

1984-04-01

A standard Liquid Metal Fast Breeder Reactor (LMFBR) subassembly used in the Experimental Breeder Reactor II (EBR-II) was investigated, by remote techniques, for fuel bundle distortion by both nondestructive and destructive methods, and the results from both methods were compared. The non-destructive method employed neutron tomography to reconstruct the locations of fuel elements through the use of a maximum entropy reconstruction algorithm known as MENT. The destructive method consisted of ''potting'' (a technique that embeds and permanently fixes the fuel elements in a solid matrix) the subassembly, and then cutting and polishing the individual sections. The comparison indicated that the tomography reconstruction provided good results in describing the bundle geometry and spacer-wire locations, with the overall resolution being on the order of a spacer-wire diameter. A dimensional consistency check indicated that the element and spacer-wire dimensions were accurately reproduced in the reconstruction

Incorporation of phenomenological uncertainties in probabilistic safety analysis - application to LMFBR core disruptive accident energetics

Energy Technology Data Exchange (ETDEWEB)

Najafi, B; Theofanous, T G; Rumble, E T; Atefi, B

1984-08-01

This report describes a method for quantifying frequency and consequence uncertainty distribution associated with core disruptive accidents (CDAs). The method was developed to estimate the frequency and magnitude of energy impacting the reactor vessel head of the Clinch River Breeder Plant (CRBRP) given the occurrence of hypothetical CDAs. The methodology is illustrated using the CRBR example.

Effects of low heterogeneity in fast critical assemblies

International Nuclear Information System (INIS)

Belov, S.P.; Dulin, V.A.; Zhukov, A.V.; Kuzin, E.N.; Mozhaev, V.K.; Sitnikov, V.I.; Tsibulya, A.M.; Shapar', A.V.; Zayfert, E.; Kuntsman, B.; Khayntsel'man, B.

1989-01-01

The problem of the low heterogeneity of fast critical assemblies, which are used to simulate fast reactors that are under design, has begun to assume increasing importance as the errors in nuclear data and group constants decrease and the capabilities of design codes improve. The design of the fuel channels of the fast critical assemblies of a BFS differs from that of the fuel subassemblies of a power reactor. The principal difference is that critical assemblies have a more heterogeneous structure than a reactor core does. As a result, the effects of this heterogeneity turn out to be appreciable for a number of functionals. Of particular interest was the measurement of the main neutronic characteristics of a fast reactor in its actual design and in the mockup produced by using BFS facilities. The authors measured and calculated the most important functionals (the ratios of the average cross sections of the main absorbing and fissioning elements, etc.) for both a homogeneous medium (fuel assemblies) and a heterogeneous medium (slugs, tubes) of practically identical composition. The objective of this work was to compare the discrepancy between experiment and calculations for the central functionals in the homogeneous and heterogeneous cases after corrections. This is a check of the accuracy of the simulation of homogeneous cores in fast power reactors by using the tools of the BFS fast critical assembly

Key technological issues in LMFBR high-temperature structural design - the US perspective

International Nuclear Information System (INIS)

Corum, J.M.

1984-01-01

The purpose of this paper is: (1) to review the key technological issues in LMFBR high-temperature structural design, particularly as they relate to cost reduction; and (2) to provide an overview of activities sponsored by the US Department of Energy to resolve the issues and to establish stable, standardized, and defensible structural design methods and criteria. Specific areas of discussion include: weldments, structural validation tests, simplified design analysis procedures, design procedures for piping, validation of the methodology for notch-like geometries, improved life assessment procedures, thermal striping, extension of the methodology to new materials, and ASME high-temperature Code reform needs. The perceived problems and needs in each area are discussed, and the current status of related US activities is given

Structural analysis for LMFBR applications[Indian position paper

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-05-01

Firstly, we discuss the use of elastic analysis for structural design of LMFBR components. The elastic analysis methods have been used for structural design of the Fast Breeder Test Reactor as well as the proposed prototype Test Breeder Reactor. The design of Fast Breeder Test Reactor which is nearing completion is the same as that of Rapsodie. Nevertheless, the design had to he checked against the latest design codes available, namely the ASME Code case 1592. This paper however, is confined to Structural analysis of PFBR components. The problems faced in the design of some of the components, in particular, the inner vessel (plenum separator) are discussed. As far as design codes are concerned, we make use of ASME Code Section III and the Code Case N-47, for high temperature design. The problem faced in the use of these rules are also described along with the description of analysis. Studies in the field of cyclic loading include extension of Bree's breakdown and plastic cycling criteria for ratchet free operation to biaxial stress fields. In other fields, namely, inelastic analysis, piping analysis in the creep regime etc. we are only at a start.

Heterogeneous skills and homogeneous land: segmentation and agglomeration

OpenAIRE

Matthias Wrede

2013-01-01

This paper analyzes the impact of skill heterogeneity on regional patterns of production and housing in the presence of pecuniary externalities within a general-equilibrium framework assuming monopolistic competition at intermediate good markets. It shows that the interplay of heterogeneous skills and relatively homogeneous land demand triggers skill segmentation and agglomeration. The core region, being more attractive to high skilled workers, has a disproportionately large share of producti...

An experimental study on sodium-water reaction in the double pool LMFBR, (4)

International Nuclear Information System (INIS)

Kumagai, Hiromichi; Yoshida, Kazuo; Uotani, Masaki; Akimoto, Tokuzo

1989-01-01

Double Pool type LMFBR set the rectangular cross-sectional steam generator (SGs) inside a secondary vessel. The initial spike pressure rise caused by large sodium-water reaction in SGs might be radiated into a large sodium pool in the secondary vessel. Therefore basic experiments on pressure wave propagation were carried out by generating pressure wave in water by mean of a set of drop hummer and piston. But the experimental apparatus in water was not convenience to simulate the structure near the bottom end of the SGs shell. In this reports, experiments were carried out by generating pulse sound pressure in air, and compared with the results pressure waves in water. (author)

An improved one-and-a-half group BWR core simulator for a new-generation core management system

International Nuclear Information System (INIS)

Iwamoto, Tatsuya; Yamamoto, Munenari

2000-01-01

An improved one-and-a-half group core simulator method for a next-generation BWR core management system is presented. In the improved method, intranodal spectral index (thermal to fast flux ratio) is expanded with analytic solutions to the diffusion equation, and the nodal power density and the interface net current are calculated, taking the intranodal flux shape into consideration. A unique method was developed for assembly heterogeneity correction. Thus eliminating the insufficiencies of the conventional one-and-a-half group method, we can have accurate power distributions as well as local peaking factors for cores having large spectral mismatch between fuel assemblies. The historical effects of spectral mismatch are also considered in both nodal power and local peaking calculations. Although reflectors are not solved explicitly, there is essentially no need for core dependent adjustable parameters, since boundary conditions are derived in the same manner as in the interior nodes. Calculation time for nodal solutions is comparable to that for the conventional method, and is less than 1/10 of a few-group nodal simulator. Verifications of the present method were made by comparing the results with those obtained by heterogeneous fine-mesh multi-group core depletion calculations, and the accuracy was shown to be fairly good. (author)

Calculation of pressure drop and flow redistribution in the core of LMFBR type reactors

International Nuclear Information System (INIS)

Botelho, D.A.; Morgado, O.J.

1985-01-01

It is studied the flow redistribution through of fuel elements to the pressure drop calculation in the core of sodium cooled reactors. Using the quasi-static formulation of equations of the conservation of mass, energy and momentum, it was developed a computer program to flow redistribution calculations and pressure drop for different power levels and total flow simulating an arbitrary number of channels for sodium flowing . An optimization of the number of sufficient channels for calculations of this nature is done. The method is applied in studies of transients in the same reactor. (M.C.K.) [pt

LMFBR plant design features for sodium spill and fire protection

International Nuclear Information System (INIS)

Palm, R.E.

1982-01-01

Design features have been developed for an LMFBR plant to protect the concrete structures from potential liquid spills and fires and prevent sodium-concrete reactions. The inclusion of these features in the plant design reduces the severity of design basis accident conditions imposed on containment and other critical plant structures. Steel liners are provided in cells containing radioactive sodium systems, and catch pans are located in non-radioactive sodium system cells. The design requirements and descriptions of each of these protective features are presented. The loading conditions, analytical approach and numerical results are also included. Design of concrete cell structures that are subject to high temperature effects from sodium spills is discussed. The structural design considers the influence of high temperature on design properties of concrete and carbon steel materials based on results of a comprehensive test program. The development of these design features and high temperature design considerations for the Clinch River Breeder Reactor Plant (CRBRP) are presented in this paper

Heat transfer performance of multilayer insulation system under roof slab of pool-type LMFBR

International Nuclear Information System (INIS)

Kinoshita, Izumi; Naohara, Nobuyuki; Uotani, Masaki

1986-01-01

To cope with thermal expansion of stainless steel plate, about 90 insulation structures are installed under the roof-slab of pool-type LMFBR. The objective of this study is to evaluate from heat transfer experiment and visualized experiment, the effect of distance between each thermal insulation structure on heat transfer characteristics of insulation system under roof-slab. Two types of insulation structures are selected, one is open type and the other is closed type. Distance between each thermal insulation structure and hot surface temperatures are varied as a parameter. Furthermore, heat flux of the roof-slab insulation system of reactor are estimated from the results of heat transfer experiment. (author)

Evaluation of the LMFBR cover gas source term and synthesis of the associated R and D

International Nuclear Information System (INIS)

Balard, F.; Carluec, B.

1996-01-01

At the end of the seventies and the beginning of the eighties, there appeared a pressing need of experimental results to assess the LMFBR's safety level. Because of the urgency, analytical studies were not systematically undertaken and maximum credible cover gas instantaneous source terms (radionuclides core release fraction) were got directly from crude out-of-pile experiment interpretations. Two types of studies and mock-ups were undertaken depending on the timescale of the phenomena: instantaneous source terms (corresponding to an unlikely energetic core disruptive accident CDA), and delayed ones (tens of minutes to some hours). The experiments performed in this frame are reviewed in this presentation: 1) instantaneous source term: - FAUST experiments: I, Cs, UO2 source terms (FzK, Germany), - FAST experiments : pool depth influence on non volatile source term (USA), - CARAVELLE experiments: nonvolatile source term in SPX1 geometry (CEA, France); 2) delayed source term: - NALA experiments: I, Cs, Sr, UO2 source term (FzK, Germany), - PAVE experiments: I source term (CEA, France), - NACOWA experiments: cover gas aerosols enrichment in I and Cs (FzK, Germany) - other French experiments in COPACABANA and GULLIVER facilities. The volatile fission products release is tightly bound to sodium evaporation and a large part of the fission products is dissolved in the liquid sodium aerosols present in the cover gas. Thus the knowledge of the amount of aerosol release to the cover gas is important for the evaluation of the source term. The maximum credible cover gas instantaneous source terms deduced from the experiments have led to conservative source terms to be taken into account in safety analysis. Nevertheless modelling attempts of the observed (in-pile or out-of-pile) physico-chemical phenomena have been undertaken for extrapolation to the reactor case. The main topics of this theoretical research are as follows: fission products evaporation in the cover gas (Fz

An axially and radially two-zoned large liquid-metal fast breeder reactor core concept

International Nuclear Information System (INIS)

Kamei, T.; Arie, K.; Moriki, Y.; Suzuki, M.; Yamaoka, M.

1985-01-01

A new core concept that has advantages over conventional homogeneous cores in neutronics characteristics such as power peaking factor, burnup reactivity loss, and reactivity response to the movement of control rods in earthquakes has been evolved. Two options of the new core concept are feasible. One is the so-called axially heterogeneous core, with the internal blanket placed at the lower part of the core. The other concept is similar to the conventional homogeneous core, but has two different plutonium-enriched zones in the axial as well as in the radial direction, so it is a hybrid type of the conventional homogeneous core and the axially heterogeneous core. The new design concept is described and the way that the core characteristics are improved by the chosen key parameters is shown

Influence of leakage flow on the behaviour of gas behind a blockage in LMFBR subassembly geometry

International Nuclear Information System (INIS)

Fukuzawa, Y.

1980-07-01

Observations were made of the behaviour of gas behind a uniform porous 21% corner blockage within a pin-bundle of LMFBR subassembly geometry. The main parameter of the experiment was the leakage flow rate through the blockage. The behaviour of gas is significantly influenced by the leakage flow rate. The measured size and residence time of a gas cavity formed behind the blockage are shown and the mechanisms of the gas cavity dispersion by the leakage flow discussed by using a simple model of the liquid flow distribution behind the blockage. (orig.) [de

Comparative analysis of quality assurance requirements for selected LMFBR components of classes 1, 2 and 3

International Nuclear Information System (INIS)

Kleinert, K.P.

1992-01-01

The study analyses and compares German, French, British and Italian practices and procedures applied for various LMFBR projects both related to the quality assurance system and related to the particular type of class of component:Class 1: primary reactor vessel; Class 2: Secondary sodium pump; Class 3: Primary cold trap. Various areas of analysis and comparison were selected to identify the underlying concepts of grading of requirements and measures, to identify the similarities and differences, and to give recommendations for further actions concerning quality assurance requirements 60 refs., 21 tabs., 6 figs

Technical assessment study on pool-type LMFBR

International Nuclear Information System (INIS)

1986-01-01

Technical assessment study on pool-type LMFBR was started in 1984 FY, inheriting the products from the Feasibility study, in order to accomplish cost reduction of reactor structure and enhanced structural reliability. This study consists of four major subjects; aseismic design development, component design optimization, high temperature structural design optimization and thermal hydraulics design optimization. In 1985 FY numbers of large model tests and analytical evaluations have been performed based on the prospects obtained in the first year's study. These tests and analyses have produced a lot of findings in each subject. They are concerning; (1) the effect of various building structures and analysis methods on floor response reduction, and data for evaluation of aseismic design concepts and structural integrity to seismic loading in the aseismic design development study. (2) data for evaluation of size reduction of main components in the reactor vessel, and heat transfer data required for structural integrity evaluation in the component design optimization study. (3) data for verification of inelastic analysis method, and assurance of technical applicability of disimilar weld in the high temperature structural design optimization study. (4) the effect of component size and location on thermal hydraulic characteristics, and data of thermal hydraulic similarity in thermal hydraulic design optimization study. This report summarizes the results obtained in 1985 FY. (author)

Cesium vapor cycle for an advanced LMFBR

International Nuclear Information System (INIS)

Fraas, A.P.

1975-01-01

A review indicates that a cesium vapor topping cycle appears attractive for use in the intermediate fluid circuit of an advanced LMFBR designed for a reactor outlet temperature of 1250 0 F or more and would have the following advantages: (1) it would increase the thermal efficiency by about 5 to 10 points (from approximately 40 percent to approximately 45 to 50 percent) thus reducing the amount of waste heat rejected to the environment by 15 to 30 percent. (2) the higher thermal efficiency should reduce the overall capital cost of the reactor plant in dollars per kilowatt. (3) the cesium can be distilled out of the intermediate fluid circuit to leave it bone-dry, thus greatly reducing the time and cost of maintenance work (particularly for the steam generator). (4) the large volume and low pressure of the cesium vapor region in the cesium condenser-steam generator greatly reduces the magnitude of pressure fluctuations that might occur in the event of a leak in a steam generator tube, and the characteristics inherent in a condenser make it easy to design for rapid concentration of any noncondensibles that may form as a consequence of a steam leak into the cesium region so that a steam leak can be detected easily in the very early stages of its development

Proceedings of the ANS/ASME/NRC international topical meeting on nuclear reactor thermal-hydraulics: LMFBR and HTGR advanced reactor concepts and analysis methods

International Nuclear Information System (INIS)

1980-01-01

Separate abstracts are included for each of the papers presented concerning the thermal-hydraulics of LMFBR type reactors; mathematical methods in nuclear reactor thermal-hydraulics; heat transfer in gas-cooled reactors; and thermal-hydraulics of pebble-bed reactors. Two papers have been previously abstracted and input to the data base

I(Re2-WiNoC: Exploring scalable wireless on-chip micronetworks for heterogeneous embedded many-core SoCs

Directory of Open Access Journals (Sweden)

Dan Zhao

2015-02-01

In this work, an irregular and reconfigurable WiNoC platform is proposed to tackle ever increasing complexity, density and heterogeneity challenges. A flexible RF infrastructure is established where RF nodes are properly distributed and IP cores are clustered. Consequently, a performance-cost effective topology is formed. A region-aided routing scheme is further deigned and implemented to realize loop-free, minimum path cost and high scalability for irregular WiNoC infrastructure. To implement the data transmission protocol, the RF microarchitecture of WiNoC is developed where the RF nodes are designed to fulfill the functions of distributed table routing, multi-channel arbitration, virtual output queuing, and distributed flow control. Our simulation studies based on synthetic traffics demonstrate the network efficiency and scalability of WiNoC.

Bottom-up control of geomagnetic secular variation by the Earth's inner core

DEFF Research Database (Denmark)

Aubert, Julien; Finlay, Chris; Fournier, Alexandre

2013-01-01

of geomagnetic secular variation. Here we show that it can be reproduced provided that two mechanisms relying on the inner core are jointly considered. First, gravitational coupling5 aligns the inner core with the mantle, forcing the flow of liquid metal in the outer core into a giant, westward drifting, sheet...... release in the outer core which in turn distorts the gyre, forcing it to become eccentric, in agreement with recent core flow inversions6, 10, 11. This bottom-up heterogeneous driving of core convection dominates top-down driving from mantle thermal heterogeneities, and localizes magnetic variations......Temporal changes in the Earth’s magnetic field, known as geomagnetic secular variation, occur most prominently at low latitudes in the Atlantic hemisphere1, 2 (that is, from −90 degrees east to 90 degrees east), whereas in the Pacific hemisphere there is comparatively little activity...

Experimental plans for LMFBR cavity liner sodium spill test LT-1

International Nuclear Information System (INIS)

Hilliard, R.K.; Newell, G.A.

1976-01-01

Reinforced concrete is an important material of construction in LMFBR cavities and cells. Steel liners are often installed on the concrete surfaces to provide a gastight seal for minimizing air inleakage to inerted cell atmospheres and to protect the concrete from direct contact with sodium in the event of a sodium spill. In making safety assessment analyses, it is of interest to determine the adequacy of the liners to maintain their leaktightness during postulated accidents involving large sodium spills. However, data for basing analytical assessments of cell liners are very meager and an experimental program is underway at HEDL to provide some of the needed information. The HEDL cell liner evaluation program consists of both bench-scale feature tests and large-scale sodium spill demonstration tests. The plans for the first large-scale sodium spill test (LT-1) are the subject of this paper

Homogenization technique for strongly heterogeneous zones in research reactors

International Nuclear Information System (INIS)

Lee, J.T.; Lee, B.H.; Cho, N.Z.; Oh, S.K.

1991-01-01

This paper reports on an iterative homogenization method using transport theory in a one-dimensional cylindrical cell model developed to improve the homogenized cross sections fro strongly heterogeneous zones in research reactors. The flux-weighting homogenized cross sections are modified by a correction factor, the cell flux ratio under an albedo boundary condition. The albedo at the cell boundary is iteratively determined to reflect the geometry effects of the material properties of the adjacent cells. This method has been tested with a simplified core model of the Korea Multipurpose Research Reactor. The results demonstrate that the reaction rates of an off-center control shroud cell, the multiplication factor, and the power distribution of the reactor core are close to those of the fine-mesh heterogeneous transport model

TREAT experimental data base regarding fuel dispersals in LMFBR loss-of-flow accidents

International Nuclear Information System (INIS)

Simms, R.; Fink, C.L.; Stanford, G.S.; Regis, J.P.

1981-01-01

The reactivity feedback from fuel relocation is a central issue in the analysis of loss-of-flow (LOF) accidents in LMFBRs. Fuel relocation has been studied in a number of LOF simulations in the TREAT reactor. In this paper the results of these tests are analyzed, using, as the principal figure of merit, the changes in equivalent fuel worth associated with the fuel motion. The equivalent fuel worth was calculated from the measured axial fuel distributions by weighting the data with a typical LMFBR fuel-worth function. At nominal power, the initial fuel relocation resulted in increases in equivalent fuel worth. Above nominal power the fuel motion was dispersive, but the dispersive driving forces could not unequivocally be identified from the experimental data

Critical experiments on enriched uranium graphite moderated cores

International Nuclear Information System (INIS)

Kaneko, Yoshihiko; Akino, Fujiyoshi; Kitadate, Kenji; Kurokawa, Ryosuke

1978-07-01

A variety of 20 % enriched uranium loaded and graphite-moderated cores consisting of the different lattice cells in a wide range of the carbon to uranium atomic ratio have been built at Semi-Homogeneous Critical Experimental Assembly (SHE) to perform the critical experiments systematically. In the present report, the experimental results for homogeneously or heterogeneously fuel loaded cores and for simulation core of the experimental reactor for a multi-purpose high temperature reactor are filed so as to be utilized for evaluating the accuracy of core design calculation for the experimental reactor. The filed experimental data are composed of critical masses of uranium, kinetic parameters, reactivity worths of the experimental control rods and power distributions in the cores with those rods. Theoretical analyses are made for the experimental data by adopting a simple ''homogenized cylindrical core model'' using the nuclear data of ENDF/B-III, which treats the neutron behaviour after smearing the lattice cell structure. It is made clear from a comparison between the measurement and the calculation that the group constants and fundamental methods of calculations, based on this theoretical model, are valid for the homogeneously fuel loaded cores, but not for both of the heterogeneously fuel loaded cores and the core for simulation of the experimental reactor. Then, it is pointed out that consideration to semi-homogeneous property of the lattice cells for reactor neutrons is essential for high temperature graphite-moderated reactors using dispersion fuel elements of graphite and uranium. (author)

Reactivity analysis of core distortion effects in the FFTF

International Nuclear Information System (INIS)

Knutson, B.J.

1982-01-01

An improved technique for evaluating core distortion reactivity effects was developed using reactivity analyses of two core geometry models (R-Z and HEX). This technique is incorporated into a new processor code called CORDIS. The advantages of this technique over existing reactivity models are that is preserves core heterogeneity, provides a control rod insertion effect model, uses row-dependent axial shape functions, and provides a flexible and cost efficient core distortion reactivity analysis method

Seismic Wave Velocity in Earth's Shallow Core

Science.gov (United States)

Alexandrakis, C.; Eaton, D. W.

2008-12-01

Studies of the outer core indicate that it is composed of liquid Fe and Ni alloyed with a ~10% fraction of light elements such as O, S or Si. Recently, unusual features, such as sediment accumulation, immiscible fluid layers or stagnant convection, have been predicted in the shallow core region. Secular cooling and compositional buoyancy drive vigorous convection that sustains the geodynamo, although critical details of light-element composition and thermal regime remain uncertain. Seismic velocity models can provide important constraints on the light element composition, however global reference models, such as Preliminary Reference Earth Model (PREM), IASP91 and AK135 vary significantly in the 200 km below the core-mantle boundary. Past studies of the outermost core velocity structure have been hampered by traveltime uncertainties due to lowermost mantle heterogeneities. The recently published Empirical Transfer Function (ETF) method has been shown to reduce the uncertainty using a waveform stacking approach to improve global observations of SmKS teleseismic waves. Here, we apply the ETF method to achieve a precise top-of-core velocity measurement of 8.05 ± 0.03 km/s. This new model accords well with PREM. Since PREM is based on the adiabatic form of the Adams-Williamson equation, it assumes a well mixed (i.e. homogeneous) composition. This result suggests a lack of heterogeneity in the outermost core due to layering or stagnant convection.

Computing effective properties of random heterogeneous materials on heterogeneous parallel processors

Science.gov (United States)

Leidi, Tiziano; Scocchi, Giulio; Grossi, Loris; Pusterla, Simone; D'Angelo, Claudio; Thiran, Jean-Philippe; Ortona, Alberto

2012-11-01

In recent decades, finite element (FE) techniques have been extensively used for predicting effective properties of random heterogeneous materials. In the case of very complex microstructures, the choice of numerical methods for the solution of this problem can offer some advantages over classical analytical approaches, and it allows the use of digital images obtained from real material samples (e.g., using computed tomography). On the other hand, having a large number of elements is often necessary for properly describing complex microstructures, ultimately leading to extremely time-consuming computations and high memory requirements. With the final objective of reducing these limitations, we improved an existing freely available FE code for the computation of effective conductivity (electrical and thermal) of microstructure digital models. To allow execution on hardware combining multi-core CPUs and a GPU, we first translated the original algorithm from Fortran to C, and we subdivided it into software components. Then, we enhanced the C version of the algorithm for parallel processing with heterogeneous processors. With the goal of maximizing the obtained performances and limiting resource consumption, we utilized a software architecture based on stream processing, event-driven scheduling, and dynamic load balancing. The parallel processing version of the algorithm has been validated using a simple microstructure consisting of a single sphere located at the centre of a cubic box, yielding consistent results. Finally, the code was used for the calculation of the effective thermal conductivity of a digital model of a real sample (a ceramic foam obtained using X-ray computed tomography). On a computer equipped with dual hexa-core Intel Xeon X5670 processors and an NVIDIA Tesla C2050, the parallel application version features near to linear speed-up progression when using only the CPU cores. It executes more than 20 times faster when additionally using the GPU.

Two-phase flow visualization under reservoir conditions for highly heterogeneous conglomerate rock: A core-scale study for geologic carbon storage.

Science.gov (United States)

Kim, Kue-Young; Oh, Junho; Han, Weon Shik; Park, Kwon Gyu; Shinn, Young Jae; Park, Eungyu

2018-03-20

Geologic storage of carbon dioxide (CO 2 ) is considered a viable strategy for significantly reducing anthropogenic CO 2 emissions into the atmosphere; however, understanding the flow mechanisms in various geological formations is essential for safe storage using this technique. This study presents, for the first time, a two-phase (CO 2 and brine) flow visualization under reservoir conditions (10 MPa, 50 °C) for a highly heterogeneous conglomerate core obtained from a real CO 2 storage site. Rock heterogeneity and the porosity variation characteristics were evaluated using X-ray computed tomography (CT). Multiphase flow tests with an in-situ imaging technology revealed three distinct CO 2 saturation distributions (from homogeneous to non-uniform) dependent on compositional complexity. Dense discontinuity networks within clasts provided well-connected pathways for CO 2 flow, potentially helping to reduce overpressure. Two flow tests, one under capillary-dominated conditions and the other in a transition regime between the capillary and viscous limits, indicated that greater injection rates (potential causes of reservoir overpressure) could be significantly reduced without substantially altering the total stored CO 2 mass. Finally, the capillary storage capacity of the reservoir was calculated. Capacity ranged between 0.5 and 4.5%, depending on the initial CO 2 saturation.

Assessment of inspectability of LMFBR designs. Final report

International Nuclear Information System (INIS)

1981-09-01

This two-volume report provides a comprehensive review of the inspectability of specific portions of loop- and pool-type LMFBR (1000-MWe) designs selected by EPRI. The designs were developed during the mid to late 1970s by three independent design teams (General Electric Co., Rockwell International, and Westinghouse) under the sponsorship of DOE (formerly ERDA) and EPRI. The requirements for normal, contingency, and post-repair inspections, addressed in this report, were established from Draft 12 of the ASME Boiler and Pressure Vessel Code, Section XI Division 3, issued in September 1979. These requirements, the intrinsic characteristics of the designs, the environmental (radiation, thermal, and atmospheric) aspects, and the available (present and near-term) inspection techniques, formed the basis for assessing the selected portions of the design or (1) accessibility, (2) feasibility, (3) practicality, and (4) costs to perform the above-specified inspections. Changes and additions fly ash has been as a concrete additive; however, extensive pilot scale development is underway to advance ash use in the TVA region in such areas as mineral and magnetite recovery, and mineral wool insulation. Recommended studies include: (1) the feasibility of converting existing wet fly d by the fuels include: residential (which includes residential and commercial), elthodology will be developed and verified in Phase II

Scoping Analysis on Core Disruptive Accident in PGSFR (2015 Results)

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Won; Chang, Won-Pyo; Ha, Kwi-Seok; Ahn, Sang June; Kang, Seok Hun; Choi, Chi-Woong; Lee, Kwi Lim; Jeong, Jae-Ho; Kim, Jin Su; Jeong, Taekyeong [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In general, the severe accident is classified by three phases. The first phase is the initiation (pre-disassembly) phase that occurs the gradual core meltdown from accident initiation to the point of neutronic shutdown with an intact geometry. The second phase is the transition phase that happens the fuel transition from a solid to a liquid phase. Fuel and cladding can melt to form a molten pool and core can boil, then criticality conditions can recur. The third phase is the disassembly phase. In other words, this phase is Core Disruptive Accident (CDA). Power excursion is followed until the core is disassembled in this phase. In the early considerations of Liquid Metal Fast Breeder Reactor (LMFBR) energetics, the term Hypothetical Core Disruptive Accidents (HCDAs) was in common use. This was not only to connote the extremely low probability of initiation of such accidents, but also the tentative nature of our understanding of their behavior and resulting consequences. A numerical analysis is conducted to estimate the energy release, pressure behavior and core expansion behavior induced by CDA of PGSFR using CDA-ER and CDA-CEME codes. Conservatively, the calculated results of energy release and pressure behavior induced by CDA without Doppler effect in PGSFR when whole cores were melted (100 $/s) were 7.844 GJ and 4.845 GPa, respectively. With Doppler effect, the analyzed maximum energy release and pressure were 6.696 GJ and 3.449 GPa, respectively. The calculated results of the core expansion behavior during 0.015 seconds after the explosion without Doppler effect in PGSFR when whole cores were melted (100 $/s) were as follows: The total energy is calculated to be 1.87 GJ. At 0.01 s, the kinetic energy of the sodium is 1.85 GJ, while the expansion work and internal energy of the bubble are 19.7 MJ and 0.98 J, respectively. With Doppler effect, the total energy is calculated to be 1.33 GJ. At 0.01 s, the kinetic energy of the sodium is 1.31 GJ, while the expansion

Local heterogeneity effects on small-sample worths

International Nuclear Information System (INIS)

Schaefer, R.W.

1986-01-01

One of the parameters usually measured in a fast reactor critical assembly is the reactivity associated with inserting a small sample of a material into the core (sample worth). Local heterogeneities introduced by the worth measurement techniques can have a significant effect on the sample worth. Unfortunately, the capability is lacking to model some of the heterogeneity effects associated with the experimental technique traditionally used at ANL (the radial tube technique). It has been suggested that these effects could account for a large portion of what remains of the longstanding central worth discrepancy. The purpose of this paper is to describe a large body of experimental data - most of which has never been reported - that shows the effect of radial tube-related local heterogeneities

Seismic isolation structure for pool-type LMFBR - isolation building with vertically isolated floor for NSSS

International Nuclear Information System (INIS)

Sakurai, A.; Shiojiri, H.; Aoyagi, S.; Matsuda, T.; Fujimoto, S.; Sasaki, Y.; Hirayama, H.

1987-01-01

The NSSS isolation floor vibration characteristics were made clear. Especially, the side support bearing (rubber bearing) is effective for horizontal floor motion restraint and rocking motion control. Seismic isolation effects for responses of the reactor components can be sufficiently expected, using the vertical seismic isolation floor. From the analytical and experimental studies, the following has been concluded: (1) Seismic isolation structure, which is suitable for large pool-type LMFBR, were proposed. (2) Seismic response characteristics of the seismic isolation structure were investigated. It was made clear that the proposed seismic isolation (Combination of the isolated building and the isolated NSSS floor) was effective. (orig./HP)

Material properties requirements for LMFBR structural design: General considerations and data needs

Energy Technology Data Exchange (ETDEWEB)

Pugh, C E [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Purdy, C M [U.S. Energy Research and Development Administration (United States)

1977-07-01

A statement is given of material properties information needed in connection with the structural design technology for liquid-metal fast breeder reactor (LMFBR) primary circuit components. Implementation of current analysis methods and criteria is considered with an emphasis on data and data correlations for performing elastic-plastic and creep analyses, for establishing allowable stress limits, and for computing creep-fatigue damage. Further development of the technology is discussed in relation to properties information. Emphasis is placed on improved constitutive equations for representing inelastic material behavior, on procedures for treating time-dependent fatigue, and on criteria for creep rupture. The properties are generally discussed without regard to specific alloys, since most categories of information are needed for each major structural material. Some sample experimental results are given for type 304 stainless steel and 2 1/4 Cr-1 Mo steel. (author)

Material properties requirements for LMFBR structural design: general considerations and data needs

International Nuclear Information System (INIS)

Pugh, C.E.; Purdy, C.M.

1977-01-01

A statement is given of material properties information needed in connection with the structural design technology for liquid-metal fast breeder reactor (LMFBR) primary circuit components. Implementation of current analysis methods and criteria is considered with an emphasis on data and data correlations for performing elastic-plastic and creep analyses, for establishing allowable stress limits, and for computing creep-fatigue damage. Further development of the technology is discussed in relation to properties information. Emphasis is placed on improved constitutive equations for representing inelastic material behavior, on procedures for treating time-dependent fatigue, and on criteria for creep rupture. The properties are generally discussed without regard to specific alloys, since most categories of information are needed for each major structural material. Some sample experimental results are given for type 304 stainless steel and 2 1 / 4 Cr-1 Mo steel

Experience on detection of leakages in LMFBR-steam generators

International Nuclear Information System (INIS)

Smit, C.C.

1975-01-01

One of the advantages of long time on full size LMFBR-components is that experience is gained nut only or, the behaviour of components at normal conditions, but also on the operational consequences (real or imaginary) disturbances. One of the most difficult situations that do occur during steam generator operation is the sudden appearance of a leak indication on the hydrogen detectors. It is possible to connect an automatic trip action to the hydrogen detector however, there are reasons not to do so. Spurious signals, which unfortunately do occur rather frequently, can cause unnecessary shut downs. In the case of a very small leak it can be very difficult to locate the leaking steam generator module and to get an impression of the size of the leak. The time available to confirm the leak, locate the component and to take the proper measures is strongly dependent on the leaking rate or translated into a visual signal, on the rate of rise of the hydrogen level shown on the instrument. During the operation of the 50 MW-SCTF at Hengelo experience was obtained with leak indications caused by real and imaginary leaks

Experience on detection of leakages in LMFBR-steam generators

Energy Technology Data Exchange (ETDEWEB)

Smit, C C

1975-07-01

One of the advantages of long time on full size LMFBR-components is that experience is gained nut only or, the behaviour of components at normal conditions, but also on the operational consequences (real or imaginary) disturbances. One of the most difficult situations that do occur during steam generator operation is the sudden appearance of a leak indication on the hydrogen detectors. It is possible to connect an automatic trip action to the hydrogen detector however, there are reasons not to do so. Spurious signals, which unfortunately do occur rather frequently, can cause unnecessary shut downs. In the case of a very small leak it can be very difficult to locate the leaking steam generator module and to get an impression of the size of the leak. The time available to confirm the leak, locate the component and to take the proper measures is strongly dependent on the leaking rate or translated into a visual signal, on the rate of rise of the hydrogen level shown on the instrument. During the operation of the 50 MW-SCTF at Hengelo experience was obtained with leak indications caused by real and imaginary leaks.

Large-scale tests of aqueous scrubber systems for LMFBR vented containment

International Nuclear Information System (INIS)

McCormack, J.D.; Hilliard, R.K.; Postma, A.K.

1980-01-01

Six large-scale air cleaning tests performed in the Containment Systems Test Facility (CSTF) are described. The test conditions simulated those postulated for hypothetical accidents in an LMFBR involving containment venting to control hydrogen concentration and containment overpressure. Sodium aerosols were generated by continously spraying sodium into air and adding steam and/or carbon dioxide to create the desired Na 2 O 2 , Na 2 CO 3 or NaOH aerosol. Two air cleaning systems were tested: (a) spray quench chamber, educator venturi scrubber and high efficiency fibrous scrubber in series; and (b) the same except with the spray quench chamber eliminated. The gas flow rates ranged up to 0.8 m 3 /s (1700 acfm) at temperatures to 313 0 C (600 0 F). Quantities of aerosol removed from the gas stream ranged up to 700 kg per test. The systems performed very satisfactorily with overall aerosol mass removal efficiencies exceeding 99.9% in each test

Single-phase pump model for analysis of LMFBR heat transport systems

International Nuclear Information System (INIS)

Madni, I.K.; Cazzoli, E.

1978-05-01

A single-phase pump model for transient and steady-state analysis of LMFBR heat transport systems is presented. Fundamental equations of the model are angular momentum balance to determine transient impeller speed and mass balance (including thermal expansion effects) to determine the level of sodium in the pump tank. Pump characteristics are modeled by homologous head and torque relations. All regions of pump operation are represented with reverse rotation allowed. The model also includes option for enthalpy rise calculations and pony motor operation. During steady state, the pump operating speed is determined by matching required head with total load in the circuit. Calculated transient results are presented for pump coastdown and double-ended pipe break accidents. The report examines the influence of frictional torque and specific speed on predicted response for the pump coastdown to natural circulation transient. The results for a double-ended pipe break accident indicate the necessity of including all regions of operation for pump characteristics

Laminar/transition sweeping flow-mixing model for wire-wrapped LMFBR assemblies

International Nuclear Information System (INIS)

Burns, K.F.; Rohsenow, W.M.; Todreas, N.E.

1980-07-01

Recent interest in analyzing the thermal hydraulic characteristics of LMFBR assemblies operating in the mixed convection regime motivates the extension of the aforementioned turbulent sweeping flow model to low Reynolds number flows. The accuracy to which knowledge of the mixing parameters is required has not been well determined, due to the increased influence of conduction and buoyancy effects with respect to energy transport at low Reynolds numbers. This study represents a best estimate attempt to correlate the existing low Reynolds number sweeping flow data. The laminar/transition model which is presented is expected to be useful in anayzing mixed convection conditions. However, the justification for making additional improvemements is contingent upon two factors. First, the ability of the proposed laminar/transition model to predict additional low Reynolds number sweeping flow data for other geometries needs to be investigated. Secondly, the sensitivity of temperature predictions to uncertainties in the values of the sweeping flow parameters should be quantified

The experiment study of the thermal insulation of the roof-slab of the main vessel of a LMFBR

International Nuclear Information System (INIS)

Wang Zhifeng; Wang Zhou; Yang Xianyong

1995-01-01

The effects of composition of insulation, i.e., reflective multi-plate thermal insulator, protecting the roof-slab of the vessel of the LMFBR on the heat transfer performance has been studied experimentally for CEFR. A economical form of the thermal insulation is suggested for CEFR. In addition, the scheme without reflective thermal insulator which has only a forced convection cooling system has been studied experimentally and a formula to calculate the average Nusselt number of the flow channel, which is valuable for CEFR design, has been raised

Density Anomalies in the Mantle and the Gravitational Core-Mantle Interaction

Science.gov (United States)

Kuang, Weijia; Liu, Lanbo

2003-01-01

Seismic studies suggest that the bulk of the mantle is heterogeneous, with density variations in depth as well as in horizontal directions (latitude and longitude). This density variation produces a three- dimensional gravity field throughout the Earth. On the other hand, the core density also varies in both time and space, due to convective core flow. Consequently, the fluid outer core and the solid mantle interact gravitationally due to the mass anomalies in both regions. This gravitational core-mantle interaction could play a significant role in exchange of angular momentum between the core and the mantle, and thus the change in Earth's rotation on time scales of decades and longer. Aiming at estimating the significance of the gravitational core-mantle interaction on Earth's rotation variation, we introduce in our MoSST core dynamics model a heterogeneous mantle, with a density distribution derived from seismic results. In this model, the core convection is driven by the buoyancy forces. And the density variation is determined dynamically with the convection. Numerical simulation is carried out with different parameter values, intending to extrapolate numerical results for geophysical implications.

Coolant mixing in LMFBR rod bundles and outlet plenum mixing transients. Final report

International Nuclear Information System (INIS)

Todreas, N.E.; Cheng, S.K.; Basehore, K.

1984-08-01

This project principally undertook the investigation of the thermal hydraulic performance of wire wrapped fuel bundles of LMFBR configuration. Results obtained included phenomenological models for friction factors, flow split and mixing characteristics; correlations for predicting these characteristics suitable for insertion in design codes; numerical codes for analyzing bundle behavior both of the lumped subchannel and distributed parameter categories and experimental techniques for pressure velocity, flow split, salt conductivity and temperature measurement in water cooled mockups of bundles and subchannels. Flow regimes investigated included laminar, transition and turbulent flow under forced convection and mixed convection conditions. Forced convections conditions were emphasized. Continuing efforts are underway at MIT to complete the investigation of the mixed convection regime initiated here. A number of investigations on outlet plenum behavior were also made. The reports of these investigations are identified

Modeling heterogeneous unsaturated porous media flow at Yucca Mountain

International Nuclear Information System (INIS)

Robey, T.H.

1994-01-01

Geologic systems are inherently heterogeneous and this heterogeneity can have a significant impact on unsaturated flow through porous media. Most previous efforts to model groundwater flow through Yucca Mountain have used stratigraphic units with homogeneous properties. However, modeling heterogeneous porous and fractured tuff in a more realistic manner requires numerical methods for generating heterogeneous simulations of the media, scaling of material properties from core scale to computational scale, and flow modeling that allows channeling. The Yucca Mountain test case of the INTRAVAL project is used to test the numerical approaches. Geostatistics is used to generate more realistic representations of the stratigraphic units and heterogeneity within units is generated using sampling from property distributions. Scaling problems are reduced using an adaptive grid that minimizes heterogeneity within each flow element. A flow code based on the dual mixed-finite-element method that allows for heterogeneity and channeling is employed. In the Yucca Mountain test case, the simulated volumetric water contents matched the measured values at drill hole USW UZ-16 except in the nonwelded portion of Prow Pass

MIT LMFBR blanket physics project progress report No. 7, July 1, 1975--September 30, 1976

International Nuclear Information System (INIS)

Driscoll, M.J.

1976-01-01

Work during the period was devoted primarily to a range of analytical/numerical investigations, including evaluation of means to improve external blanket designs, beneficial attributes of the use of internal blankets, improved methods for the calculation of heterogeneous self-shielding and parametric studies of calculated spectral indices. Experimental work included measurements of the ratio of U-238 captures to U-235 fissions in a standard blanket mockup, and completion of development work on the radiophotoluminescent readout of LiF thermoluminescent detectors. The most significant findings were that there is very little prospect for substantial improvement in the breeding performance of external blankets, but internal blankets continue to show promise, particularly if they are used in such a way as to increase the volume fraction of fuel inside the core envelope. An improved equivalence theorem was developed which may allow use of fast reactor methods to calculate heterogeneously self-shielded cross sections in both fast and thermal reactors

Thermochemical aspects of fuel-cladding and fuel-coolant interactions in LMFBR oxide fuel pins

International Nuclear Information System (INIS)

Adamson, M.G.; Aitken, E.A.; Caputi, R.W.; Potter, P.E.; Mignanelli, M.A.

1979-01-01

This paper examines several thermochemical aspects of the fuel-cladding, fuel-coolant and fuel-fission product interactions that occur in LMFBR austenitic stainless steel-clad mixed (U,Pu)-oxide fuel pins during irradiation under normal operating conditions. Results are reported from a variety of high temperature EMF cell experiments in which continuous oxygen activity measurements on reacting and equilibrium mixtures of metal oxides and (excess) liquid alkali metal (Na, K, Cs) were performed. Oxygen potential and 0:M thresholds for Na-fuel reactions are re-evaluated in the light of new measurements and newly-assessed thermochemical data, and the influence on oxygen potential of possible U-Pu segregation between oxide and urano-plutonate (equilibrium) phases has been analyzed. (orig./RW) [de

Detection of oscillatory components in noise signals and its application to fast detection of sodium boiling in LMFBR's

International Nuclear Information System (INIS)

Ehrhardt, J.

1975-09-01

In general, the surveillance of technical plants is performed by observating the mean value of measured signals. In this method not all information included in these signals is used. On the other hand - for example in a reactor - disturbances are possible which generate small oscillatory components in the measured signals. In general, these oscillatory components do not influence the mean value of the signals and consequently do not activate the conventional control system; however they can be found by analysis of the signal's noise component. For the detection of these oscillatory signals the observation of the frequency spectra of the noise signals is particularly advantageous because they produce peaks at the oscillation frequencies. In this paper a new detection system for the fast detection of suddenly appearing peaks in the frequency spectra of noise signals is presented. The prototype of a compact detection unit was developed which continuously computes the power spectral density (PSD) of noise signals and simultaneously supervises the PSD for peaks in the relevant frequency range. The detection method is not affected by the frequency dependance of the PSD and is applicable to any noise signal. General criteria were developed to enable the determination of the optimal detection system and its sensitivity. The upper limits of false alarm rate and detection time were taken into account. The detection criteria are applicable to all noise signals with approximately normally distributed amplitudes. Theoretical results were confirmed in a number of experiments; special experimental and theoretical parameter studies were done for the optimal detection of sodium boiling in LMFBR's. Computations based on these results showed that local and integral sodium boiling can be detected in a wide core range of SNR 300 by observing fluctuations of the neutron flux. In this connection it is important to point out that no additional core instrumentation is necessary because the

FAST: framework for heterogeneous medical image computing and visualization.

Science.gov (United States)

Smistad, Erik; Bozorgi, Mohammadmehdi; Lindseth, Frank

2015-11-01

Computer systems are becoming increasingly heterogeneous in the sense that they consist of different processors, such as multi-core CPUs and graphic processing units. As the amount of medical image data increases, it is crucial to exploit the computational power of these processors. However, this is currently difficult due to several factors, such as driver errors, processor differences, and the need for low-level memory handling. This paper presents a novel FrAmework for heterogeneouS medical image compuTing and visualization (FAST). The framework aims to make it easier to simultaneously process and visualize medical images efficiently on heterogeneous systems. FAST uses common image processing programming paradigms and hides the details of memory handling from the user, while enabling the use of all processors and cores on a system. The framework is open-source, cross-platform and available online. Code examples and performance measurements are presented to show the simplicity and efficiency of FAST. The results are compared to the insight toolkit (ITK) and the visualization toolkit (VTK) and show that the presented framework is faster with up to 20 times speedup on several common medical imaging algorithms. FAST enables efficient medical image computing and visualization on heterogeneous systems. Code examples and performance evaluations have demonstrated that the toolkit is both easy to use and performs better than existing frameworks, such as ITK and VTK.

Workload Balancing on Heterogeneous Systems: A Case Study of Sparse Grid Interpolation

KAUST Repository

Muraraşu, Alin

2012-01-01

Multi-core parallelism and accelerators are becoming common features of today’s computer systems, as they allow for computational power without sacrificing energy efficiency. Due to heterogeneity, tuning for each type of compute unit and adequate load balancing is essential. This paper proposes static and dynamic solutions for load balancing in the context of an application for visualizing high-dimensional simulation data. The application relies on the sparse grid technique for data compression. Its performance critical part is the interpolation routine used for decompression. Results show that our load balancing scheme allows for an efficient acceleration of interpolation on heterogeneous systems containing multi-core CPUs and GPUs.

Performance of LMFBR fuel pins with (Pu,Th)O/sub 2-x/ and UO2

International Nuclear Information System (INIS)

Lawrence, L.A.

1983-09-01

The irradiation performance of (Pu,Th)O/sub 2-x/ and UO 2 fueled pins for breeder reactor application were compared to the extensive performance data base for the (U,Pu)O/sub 2-x/ fuel system. Th-Pu and 238 U- 233 U based fuel systems were candidate fuel fertile/fissile isotopic combinations for development of alternatives to the current LMFBR fuel cycle. Initial screening tests were conducted in the EBR-II to obtain comparative performance data because of the limited experience with these fuel systems. In some cases, 235 U was used as a substitute for 233 U because of the difficulties in fabrication of available 233 U due to its high gamma ray emission rate

Materials properties utilization in a cumulative mechanical damage function for LMFBR fuel pin failure analysis

International Nuclear Information System (INIS)

Jacobs, D.C.

1977-01-01

An overview is presented of one of the fuel-pin analysis techniques used in the CRBRP program, the cumulative mechanical damage function. This technique, as applied to LMFBR's, was developed along with the majority of models used to describe the mechanical properties and environmental behavior of the cladding (i.e., 20 percent cold-worked, 316 stainless steel). As it relates to fuel-pin analyses the Cumulative Mechanical Damage Function (CDF) continually monitors cladding integrity through steady state and transient operation; it is a time dependent function of temperature and stress which reflects the effects of both the prior mechanical history and the variations in mechanical properties caused by exposure to the reactor environment

French experimental facilities for measurements of transverse flows and assessment of the corresponding risk of vibrations in heterogeneous cores

International Nuclear Information System (INIS)

Le Borgne, E.; Mattei, A.; Oceraies, Y.; Fardeau, P.

1994-01-01

Due to insertion of a limited number of new assemblies at each cycle, the cores in Pressurized Water Reactors are not homogeneous. Referring only to the impact on coolant flow, these differences can range from variable hydraulic resistances in the assembly, which depend on the geometric changes occurring during preceding cycles, to coexistence of assemblies with new design structures. Deviations in resistance between neighboring fuel assemblies causes the flow rates to be distributed differently between the assembly rods. This results in development of transverse flows from the main axial flow, and changes in the axial velocity gradients. These particularities of coolant flow have an effect on both vibration levels and cooling of the fuel rods, and also on the axial forces exerted on the assemblies in the core cavity. Since 1985, French Atomic Energy Commission (CEA) has gradually acquired experimental and measuring facilities that have allowed it to engage in research and development programs in these areas, in cooperation with industry partners in the nuclear field. Two complementary test loops have been constructed, called ARIANE and HERMES T. Use of these experimental facilities allows to obtain complete and detailed information on the hydraulic and vibratory phenomena specific to heterogeneous cores. In particular it is possible to establish a direct assessment of the actual compatibility between two different assemblies. By making a few specific changes, these facilities can also be used as a unique tool for assembly behaviour studies under seismic conditions with simulation of the flow effects. Also, a source of information in thus made available for qualification of computation codes for vibratory mechanics and multidimensional fluid mechanics under development at CEA and also used in the field of nuclear fuel. (authors). 6 figs., 1 ref

Statistical mechanical analysis of LMFBR fuel cladding tubes

International Nuclear Information System (INIS)

Poncelet, J.-P.; Pay, A.

1977-01-01

The most important design requirement on fuel pin cladding for LMFBR's is its mechanical integrity. Disruptive factors include internal pressure from mixed oxide fuel fission gas release, thermal stresses and high temperature creep, neutron-induced differential void-swelling as a source of stress in the cladding and irradiation creep of stainless steel material, corrosion by fission products. Under irradiation these load-restraining mechanisms are accentuated by stainless steel embrittlement and strength alterations. To account for the numerous uncertainties involved in the analysis by theoretical models and computer codes statistical tools are unavoidably requested, i.e. Monte Carlo simulation methods. Thanks to these techniques, uncertainties in nominal characteristics, material properties and environmental conditions can be linked up in a correct way and used for a more accurate conceptual design. First, a thermal creep damage index is set up through a sufficiently sophisticated clad physical analysis including arbitrary time dependence of power and neutron flux as well as effects of sodium temperature, burnup and steel mechanical behavior. Although this strain limit approach implies a more general but time consuming model., on the counterpart the net output is improved and e.g. clad temperature, stress and strain maxima may be easily assessed. A full spectrum of variables are statistically treated to account for their probability distributions. Creep damage probability may be obtained and can contribute to a quantitative fuel probability estimation

Scale modelling in LMFBR safety

International Nuclear Information System (INIS)

Cagliostro, D.J.; Florence, A.L.; Abrahamson, G.R.

1979-01-01

This paper reviews scale modelling techniques used in studying the structural response of LMFBR vessels to HCDA loads. The geometric, material, and dynamic similarity parameters are presented and identified using the methods of dimensional analysis. Complete similarity of the structural response requires that each similarity parameter be the same in the model as in the prototype. The paper then focuses on the methods, limitations, and problems of duplicating these parameters in scale models and mentions an experimental technique for verifying the scaling. Geometric similarity requires that all linear dimensions of the prototype be reduced in proportion to the ratio of a characteristic dimension of the model to that of the prototype. The overall size of the model depends on the structural detail required, the size of instrumentation, and the costs of machining and assemblying the model. Material similarity requires that the ratio of the density, bulk modulus, and constitutive relations for the structure and fluid be the same in the model as in the prototype. A practical choice of a material for the model is one with the same density and stress-strain relationship as the operating temperature. Ni-200 and water are good simulant materials for the 304 SS vessel and the liquid sodium coolant, respectively. Scaling of the strain rate sensitivity and fracture toughness of materials is very difficult, but may not be required if these effects do not influence the structural response of the reactor components. Dynamic similarity requires that the characteristic pressure of a simulant source equal that of the prototype HCDA for geometrically similar volume changes. The energy source is calibrated in the geometry and environment in which it will be used to assure that heat transfer between high temperature loading sources and the coolant simulant and that non-equilibrium effects in two-phase sources are accounted for. For the geometry and flow conitions of interest, the

Theory and use of GIRAFFE for analysis of decay characteristics of delayed-neutron precursors in an LMFBR

International Nuclear Information System (INIS)

Gross, K.C.

1980-07-01

The application of the computer code GIRAFFE (General Isotope Release Analysis For Failed Elements) written in FORTRAN IV is described. GIRAFFE was designed to provide parameter estimates of the nonlinear discrete-measurement models that govern the transport and decay of delayed-neutron precursors in a liquid-metal fast breeder reactor (LMFBR). The code has been organized into a set of small, relatively independent and well-defined modules to facilitate modification and maintenance. The program logic, the numerical techniques, and the methods of solution used by the code are presented, and the functions of the MAIN program and of each subroutine are discussed

Anisotropic structure of the Inner Core and its uncertainty from transdimensional body-wave tomography

Science.gov (United States)

Burdick, S.; Waszek, L.; Lekic, V.

2017-12-01

Studies of body waves and normal modes have revealed strong quasi-hemispheric variations in seismic velocity, anisotropy and attenuation in the inner core. A rigorous mapping of the hemispheric boundaries and smaller scale heterogeneity within the hemispheres is crucial for distinguishing between hypotheses about inner core formation and evolution. However, the relatively sparse and heterogeneous distribution of paths piercing the inner core creates difficulties in constraining the boundaries and sub-hemispheric variations with body wave tomography. Damped tomographic inversions tend to smooth out strong structural gradients and risk carrying the imprint of sparse path coverage, while under-parametrized models can miss pertinent small-scale variations. For these reasons, we apply a probabilistic and transdimensional (THB) tomography method on core-sensitive differential P-wave traveltimes. The THB approach is well-suited to the problem of inner core tomography since 1) it remains parsimonious by allowing the parametrization to be determined the requirements of the data and 2) it preserves sharp boundaries in seismic properties, allowing it to capture both short-wavelength structure and the strong hemispheric dichotomy. Furthermore, the approach yields estimates of uncertainty in isotropic and anisotropic velocity, hemispheric boundary geometry, anisotropy axis and the tradeoffs between these properties. We quantify the effects of mantle heterogeneity with inner core structure and place constraints on inner core dynamics and minerology.

Coordinated Energy Management in Heterogeneous Processors

Directory of Open Access Journals (Sweden)

Indrani Paul

2014-01-01

Full Text Available This paper examines energy management in a heterogeneous processor consisting of an integrated CPU–GPU for high-performance computing (HPC applications. Energy management for HPC applications is challenged by their uncompromising performance requirements and complicated by the need for coordinating energy management across distinct core types – a new and less understood problem. We examine the intra-node CPU–GPU frequency sensitivity of HPC applications on tightly coupled CPU–GPU architectures as the first step in understanding power and performance optimization for a heterogeneous multi-node HPC system. The insights from this analysis form the basis of a coordinated energy management scheme, called DynaCo, for integrated CPU–GPU architectures. We implement DynaCo on a modern heterogeneous processor and compare its performance to a state-of-the-art power- and performance-management algorithm. DynaCo improves measured average energy-delay squared (ED2 product by up to 30% with less than 2% average performance loss across several exascale and other HPC workloads.

THEHYCO-3DT: Thermal hydrodynamic code for the 3 dimensional transient calculation of advanced LMFBR core

Energy Technology Data Exchange (ETDEWEB)

Vitruk, S.G.; Korsun, A.S. [Moscow Engineering Physics Institute (Russian Federation); Ushakov, P.A. [Institute of Physics and Power Engineering, Obninsk (R)] [and others

1995-09-01

The multilevel mathematical model of neutron thermal hydrodynamic processes in a passive safety core without assemblies duct walls and appropriate computer code SKETCH, consisted of thermal hydrodynamic module THEHYCO-3DT and neutron one, are described. A new effective discretization technique for energy, momentum and mass conservation equations is applied in hexagonal - z geometry. The model adequacy and applicability are presented. The results of the calculations show that the model and the computer code could be used in conceptual design of advanced reactors.

THEHYCO-3DT: Thermal hydrodynamic code for the 3 dimensional transient calculation of advanced LMFBR core

International Nuclear Information System (INIS)

Vitruk, S.G.; Korsun, A.S.; Ushakov, P.A.

1995-01-01

The multilevel mathematical model of neutron thermal hydrodynamic processes in a passive safety core without assemblies duct walls and appropriate computer code SKETCH, consisted of thermal hydrodynamic module THEHYCO-3DT and neutron one, are described. A new effective discretization technique for energy, momentum and mass conservation equations is applied in hexagonal - z geometry. The model adequacy and applicability are presented. The results of the calculations show that the model and the computer code could be used in conceptual design of advanced reactors

The Role of Node Heterogeneity in the Coupled Spreading of Epidemics and Awareness.

Science.gov (United States)

Guo, Quantong; Lei, Yanjun; Xia, Chengyi; Guo, Lu; Jiang, Xin; Zheng, Zhiming

2016-01-01

Exploring the interplay between information spreading and epidemic spreading is a topic that has been receiving increasing attention. As an efficient means of depicting the spreading of information, which manifests as a cascade phenomenon, awareness cascading is utilized to investigate this coupled transmission. Because in reality, different individuals facing the same epidemic will exhibit distinct behaviors according to their own experiences and attributes, it is important for us to consider the heterogeneity of individuals. Consequently, we propose a heterogeneous spreading model. To describe the heterogeneity, two of the most important but radically different methods for this purpose, the degree and k-core measures, are studied in this paper through three models based on different assumptions. Adopting a Markov chain approach, we succeed in predicting the epidemic threshold trend. Furthermore, we find that when the k-core measure is used to classify individuals, the spreading process is robust to these models, meaning that regardless of the model used, the spreading process is nearly identical at the macroscopic level. In addition, the k-core measure leads to a much larger final epidemic size than the degree measure. These results are cross-checked through numerous simulations, not only of a synthetic network but also of a real multiplex network. The presented findings provide a better understanding of k-core individuals and reveal the importance of considering network structure when investigating various dynamic processes.

Transition phase in LMFBR hypothetical accidents

International Nuclear Information System (INIS)

Ostensen, R.W.; Henninger, R.J.; Jackson, J.F.

1976-01-01

Mechanistic analyses of transient-under-cooling accidents have led in some cases to a mild initiating phase instead of a direct hydrodynamic disassembly of the core. The fuel is then trapped in the core by the strong mechanical surroundings and blockages formed by refrozen cladding steel and/or fuel. The formation of fuel blockages has been verified experimentally. The bottled-up core will boil on fission and decay heat, with steel as the working fluid. Boil-up in a churn turbulent flow regime may prevent recriticality due to fuel recompaction. Ultimate fuel removal from the core is probably by a two-phase blow-down after permanent leakage paths are opened. However, a vigorous recriticality can not be precluded. Reactors with void coefficients larger than that in CRBR are more likely to disassemble in the initiating phase, so the transition phase may be unique to small cores

Specialists' meeting on theoretical modelling of LMFBR fuel pin behaviour. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-12-01

The purpose of the meeting was to provide an opportunity for exchanging views of theoretical modelling of LMFBR fuel pin behaviour and to summarise the IWGFR member countries' knowledge in this field. The special emphasis was placed on normal operating conditions. The technical part of the meeting was divided into six sessions, as follows: An overview of fuel modelling studies; Key factors and basic phenomena relevant to fuel pin behaviour modelling; Application to steady state operation and normal transients; Experimental validation through pins in service and specific irradiation experiments; Advanced fuels; and Brief review of existing codes. During the meeting, papers were presented by the delegates on behalf of their countries or organization. The papers, which are included in this report, were either in the form of a general survey of the subject, or on specific technical subjects. In each subject area presentations appropriate to the subject were made from the submitted papers. The presentations were followed by discussions of the questions raised and summary is made.

LIMBO computer code for analyzing coolant-voiding dynamics in LMFBR safety tests

International Nuclear Information System (INIS)

Bordner, G.L.

1979-10-01

The LIMBO (liquid metal boiling) code for the analysis of two-phase flow phenomena in an LMFBR reactor coolant channel is presented. The code uses a nonequilibrium, annular, two-phase flow model, which allows for slip between the phases. Furthermore, the model is intended to be valid for both quasi-steady boiling and rapid coolant voiding of the channel. The code was developed primarily for the prediction of, and the posttest analysis of, coolant-voiding behavior in the SLSF P-series in-pile safety test experiments. The program was conceived to be simple, efficient, and easy to use. It is particularly suited for parametric studies requiring many computer runs and for the evaluation of the effects of model or correlation changes that require modification of the computer program. The LIMBO code, of course, lacks the sophistication and model detail of the reactor safety codes, such as SAS, and is therefore intended to compliment these safety codes

Specialists' meeting on theoretical modelling of LMFBR fuel pin behaviour. Summary report

International Nuclear Information System (INIS)

1979-12-01

The purpose of the meeting was to provide an opportunity for exchanging views of theoretical modelling of LMFBR fuel pin behaviour and to summarise the IWGFR member countries' knowledge in this field. The special emphasis was placed on normal operating conditions. The technical part of the meeting was divided into six sessions, as follows: An overview of fuel modelling studies; Key factors and basic phenomena relevant to fuel pin behaviour modelling; Application to steady state operation and normal transients; Experimental validation through pins in service and specific irradiation experiments; Advanced fuels; and Brief review of existing codes. During the meeting, papers were presented by the delegates on behalf of their countries or organization. The papers, which are included in this report, were either in the form of a general survey of the subject, or on specific technical subjects. In each subject area presentations appropriate to the subject were made from the submitted papers. The presentations were followed by discussions of the questions raised and summary is made

Results of tests under normal and abnormal operating conditions concerning LMFBR fuel element behaviour

International Nuclear Information System (INIS)

Languille, A.; Bergeonneau, P.; Essig, C.; Guerin, Y.

1985-04-01

The objective of this paper is to improve the knowledge on LMFBR fuel element behaviour during protected and unprotected transients in RAPSODIE and PHENIX reactors in order to evaluate its reliability. The range of the tests performed in these reactors is sufficiently large to cover normal and also extreme off normal conditions such as fuel melting. Results of such tests allow to better establish transient design limits for reactor structural components in particular for fuel pin cladding which play a lead role in controlling the accident sequence. Three main topics are emphasized in this paper: fuel melting during slow over-power excursions; influence of the fuel element geometrical evolution on reactivity feedback effects and reactor dynamic behaviour; clad damage evaluation during a transient (essentially very severe loss of flow)

Developments in gaseous core reactor technology

International Nuclear Information System (INIS)

Diaz, N.J.; Dugan, E.T.

1979-01-01

An effort to characterize the most promising concepts for large, central-station electrical generation was done under the auspices of the Nonproliferation Alternative Systems Assessment Program (NASAP). The two leading candidates were identified from this effort: The Mixed-Flow Gaseous Core Reactor (MFGCR) and the Heterogeneous Gas Core Reactor (HGCR). Key advantages over other nuclear concepts are weighed against the disadvantages of an unproven technology and the cost-time for deployment to make a sound decision on RandD support for these promising reactor alternatives. 38 refs

Studies of flow stratification in the hot plenum of an LMFBR

Energy Technology Data Exchange (ETDEWEB)

Jones, P; Hickmott, S [Central Electricity Generating Board, Berkeley Nuclear Laboratories, Berkeley, Gloucestershire (United Kingdom)

1983-07-01

The paper reviews work at Berkeley Nuclear Laboratories on the extent and effects of buoyancy in the hot plenum of an LMFBR. It summarizes the experimental, theoretical and numerical work has has been conducted to aid the understanding of the complex transient flows which occur following a reactor trip. The experimental work has been conducted in small-scale idealised geometries which isolate the essential features of the reactor flows and is not intended to provide detailed design data. An integral theory has been devised to describe the thermal hydraulics of negatively-buoyant jets. The predictions are shown to be in good agreement with the experimental results and emphasize the need to correctly represent the inlet velocity and temperature profiles. Some preliminary calculations with a transient, two-dimensional, finite-element code are compared with the experimental results. These calculations reproduce the overall features of the flows but not the details of the stratified interface. The development of turbulence models for stratified flows is seen as a fruitful area for further research. (author)

Incorporating the Impacts of Small Scale Rock Heterogeneity into Models of Flow and Trapping in Target UK CO2 Storage Systems

Science.gov (United States)

Jackson, S. J.; Reynolds, C.; Krevor, S. C.

2017-12-01

Predictions of the flow behaviour and storage capacity of CO2 in subsurface reservoirs are dependent on accurate modelling of multiphase flow and trapping. A number of studies have shown that small scale rock heterogeneities have a significant impact on CO2flow propagating to larger scales. The need to simulate flow in heterogeneous reservoir systems has led to the development of numerical upscaling techniques which are widely used in industry. Less well understood, however, is the best approach for incorporating laboratory characterisations of small scale heterogeneities into models. At small scales, heterogeneity in the capillary pressure characteristic function becomes significant. We present a digital rock workflow that combines core flood experiments with numerical simulations to characterise sub-core scale capillary pressure heterogeneities within rock cores from several target UK storage reservoirs - the Bunter, Captain and Ormskirk sandstone formations. Measured intrinsic properties (permeability, capillary pressure, relative permeability) and 3D saturations maps from steady-state core flood experiments were the primary inputs to construct a 3D digital rock model in CMG IMEX. We used vertical end-point scaling to iteratively update the voxel by voxel capillary pressure curves from the average MICP curve; with each iteration more closely predicting the experimental saturations and pressure drops. Once characterised, the digital rock cores were used to predict equivalent flow functions, such as relative permeability and residual trapping, across the range of flow conditions estimated to prevail in the CO2 storage reservoirs. In the case of the Captain sandstone, rock cores were characterised across an entire 100m vertical transect of the reservoir. This allowed analysis of the upscaled impact of small scale heterogeneity on flow and trapping. Figure 1 shows the varying degree to which heterogeneity impacted flow depending on the capillary number in the

Critical experiment program of heterogeneous core composed for LWR fuel rods and low enriched uranyl nitrate solution

International Nuclear Information System (INIS)

Miyoshi, Yoshinori; Yamamoto, Toshihiro; Watanabe, Shouichi; Nakamura, Takemi

2003-01-01

In order to stimulate the criticality characteristics of a dissolver in a reprocessing plant, a critical experiment program of heterogeneous cores is under going at a Static Critical Experimental Facility, STACY in Japan Atomic Energy Research Institute, JAERI. The experimental system is composed of 5w/o enriched PWR-type fuel rod array immersed in 6w/o enriched uranyl nitrate solution. First series of experiments are basic benchmark experiments on fundamental critical data in order to validate criticality calculation codes for 'general-form system' classified in the Japanese Criticality Safety Handbook, JCSHB. Second series of experiments are concerning the neutron absorber effects of fission products related to the burn-up credit Level-2. For demonstrating the reactivity effects of fission products, reactivity effects of natural elements such as Sm, Nd, Eu and 103 Rh, 133 Cs, solved in the nitrate solution are to be measured. The objective of third series of experiments is to validate the effect of gadolinium as a soluble neutron poison. Properties of temperature coefficients and kinetic parameters are also studied, since these parameters are important to evaluate the transient behavior of the criticality accident. (author)

Active acoustic leak detection for LMFBR steam generator. Sound attenuation due to bubbles

International Nuclear Information System (INIS)

Kumagai, Hiromichi; Sakuma, Toshio

1995-01-01

In the steam generators (SG) of LMFBR, it is necessary to detect the leakage of water from tubes of heat exchangers as soon as it occurs. The active acoustic detection method has drawn general interest owing to its short response time and reduction of the influence of background noise. In this paper, the application of the active acoustic detection method for SG is proposed, and sound attenuation by bubbles is investigated experimentally. Furthermore, using the SG sector model, sound field characteristics and sound attenuation characteristics due to injection of bubbles are studied. It is clarified that the sound attenuation depends upon bubble size as well as void fraction, that the distance attenuation of sound in the SG model containing heat transfer tubes is 6dB for each two-fold increase of distance, and that emitted sound attenuates immediately upon injection of bubbles. (author)