WorldWideScience

Sample records for hendo ni kansuru

  1. Solidification and transformation behavior of Cr-Ni stainless steel weld metals with ferritic single phase solidification mode. Report 4. Study on solidification and subsequent transformation of Cr-Ni stainless steel weld metals; Feraito tanso de gyokosuru Cr-Ni kei sutenresu ko yosetsu kinzoku no gyoko/hendo kyodo. 4. Cr-Ni kei sutenresu ko yosetsu kinzoku no gyoko/hentai ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, H.; Koseki, T.; Okita, S.; Fuji, M. [Nippon Steel Corp., Tokyo (Japan)

    1997-05-05

    The solidification modes of {gamma} stainless steel that solidifies at initial crystal {delta} are classified into FA mode where solidification at two phase of {delta}+{gamma} takes place after crystallization at {gamma} phase during solidification and F mode where solidification is completed at {delta} single phase, and solidification transformation behaviors of weld metal of FA mode are reported in the previous paper. Hereupon, in this report, solidification and transformation behaviors of stainless steel weld metal of F mode are studied. Cr-Ni stainless steel of F mode consists of two phase stainless steel with two phase base metal structure of {delta}+{gamma} besides {gamma} stainless steel. Further, two phase stainless steel with higher alloy compared to conventional one has been developed. In this report, not only the {gamma} stainless steel but also two phase stainless weld metals with varied amount of alloying metal are studied. The welding method and welding conditions are same as that of previous paper. Observation of structure was carried out by optical microscope, and crystal orientation and element distribution were measured by EBSP and CMA respectively. 11 refs., 18 figs., 1 tab.

  2. Experimental study on the wall jet over a riblet surface. ; Measurement of mean and fluctuating velocities and estimation of drag reduction. Riburetto men ni sou hekimen funryu ni kansuru jikkenteki kenkyu. ; Heikin-hendo sokudoba to teiko gensho no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, S. (Gifu Univ., Gifu (Japan). Faculty of Engineering); Hayashimoto, H. (Gifu Univ., Gifu (Japan). Graduate School); Inoue, Y. (Suzuka National College of Technology, Mie (Japan)); Iwakami, Y.

    1994-04-25

    A wall-jet has a wide range of application such as to control of the boundary layer of a wing of an aeroplane, control of temperature of the vanes of a gas turbine and flow inside a fluid control device. This field of flow comprises a wall layer on the wall side having the characteristics of a boundary layer and an outer layer on the external side which is like a free jet, the two layers being separated by a boundary where the flow is at a maximum speed. This study was carried out to clarify the effect of riblets experimentally using as a base jet a wall jet which was one of basic shearing flows. In particular, studied were the degrees of change in the mean and fluctuating velocities near the wall surface and reduction of drag. The following results were obtained. A significant difference was recognized in the vicinity of the wall in the mean velocity distribution between the mean velocities on the riblet surface and on the smooth surface. The fluctuating velocity component in the x direction on the riblet surface decreased by about a maximum of 20% when compared with that on the smooth surface. In contrast, the fluctuating velocity in the y direction and Reynolds shearing stress both on the riblet and smooth surfaces were substantially in agreement with each other within the range of this experiment. 28 refs., 12 figs., 1 tab.

  3. Erosion due to impingement of a cavitating jet. 4th report. Effects of nozzles shape and upstream pressure pulsation; Kyabiteshon kaishoku ni kansuru kenkyu. 4. Shibori keijo oyobi joryu atsuryoku hendo no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, J.; Wang, Xiongying [Yokohama National Univ. (Japan). Faculty of Engineering; Kazama, T. [Muroran Inst. of Technology, Hokkaido (Japan)

    1997-05-15

    Erosion related to the collision of jet flow including cavitation bubble is one of the factor to verify the limitation of hydrostatic technology. The authors have so far investigated the effect of unsteady flow, up and down stream pressure, cavitation constant, specimen material and form, laboratory conditions, form around the nozzle path and nozzle outlet and so forth on erosion using jet flow collision type cavitation erosion experimental instrument that makes possible the easy handling of the phenomena caused in machines. Further, equation for estimating the amount of erosion was derived and level of effects of main factors was clarified. However, this method was limited to only circular nozzle fixed flow. In this report, comparative study of orifice nozzle and circular nozzle at both constant normal flow and unsteady flow was carried out using same experimental instrument as in the previous report. As a result, as for the nozzle used in this experiment, erosion in case of orifice nozzle was higher than that of circular nozzle. 15 refs., 13 figs.

  4. Basic research on energy conservation in developing countries. Report of the International Conference on Adaptation and Mitigation Technologies for Climate Change; Hatten tojokoku energy shohi koritsuka kiso chosanado jigyo. Kiko hendo ni kansuru tekio kanwa gijutsu kokusai kaigi hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The International Conference on Adaptation and Mitigation Technologies for Climate Change was held based on the 1st Conference of the Parties in 1995 of the United Nations Framework Convention on Climate Change, and the 2nd evaluation report of the Intergovernmental Panel on Climate Change (IPCC). This report carries the outline of this conference and minutes. Japanese government had studied the framework of activities implemented jointly (AIJ) for emission control of greenhouse gases by voluntary workers jointly with developing countries. The government decided the basis of the AIJ Japan program in 1995, and approved the evaluation guidelines of this program including confirmed and considered matters which are necessary for government offices related to this program to evaluate and approve each project. IPCC approved the 2nd evaluation report in its general meeting in 1995. This conference was thus held to discuss strategic technology and international cooperation with participation of writers of the 2nd IPCC report, policy planners of Asian countries, Japanese industries, governmental offices and NGO.

  5. Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

  6. Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, S.; Suzuki, T.; Yamamoto, M. [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

    1997-02-01

    This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

  7. Project for the basic survey of enhancing energy consumption efficiency in developing countries. Summary of the Conference on the Policies and Measures of Climate Change Mitigation; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Kiko hendo kanwasaku no seisaku to sochi ni kansuru kokusai kaigi hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The Conference on the Policies and Measures of Climate Change Mitigation was held in Tokyo on January 28, 1997, with participation in the conference from governments, research institutes, industrial circles, NGO, etc. of ten countries including Japan. In the session `technology transfer,` presentations were made on `the current status of the technology transfer, and the expectation and requests` by Australia and Japan which provide technology and by China which receives technology. As a whole, every country recognized importance of technology transfer of both hardware and software, private sectors` taking leadership, the use of international organizations dealing with fund supply and credit guarantee. In the session `tradable permits/quotas,` Dr. A. Haspel, U.S. Department of Energy reported the structure and effect of U.S. tradable emission permits on sulfur dioxide from thermal power plants, and proposed tradable emission permits against greenhouse effect gas. The proposal needs to be further studied and discussed, and it was regarded as too early to include the proposal in the protocol to be conducted at COP3

  8. Sintering behavior of YSZ/NiO-YSZ two-layer cermics for tubular SOFC fabricated by multilayer slurry casting process. Taso slurry Kyasuto ho ni yotte sakuseishita entogata SOFC yo nisokan no shosei process ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Okuyama, R.; Nomura, E. (Yuasa Corp., Osaka (Japan). Central Lab.)

    1993-09-01

    The multilayer slurry casting process was developed, in which the fuel electrode and the electrolyte of the solid electrolyte fuel cell (SOFC) were simultaneously formed and sintered using slip cast method. The fracture behavior was investigated in the course of sintering the two-layer tube of electrolyte/fuel electrode for SOFC prepared by this method. The comparison was made in NiO content in the fuel electrode and the fracture of the double layer tube between the 3 mol% YSZ electrolyte and 8 mol% YSZ electrolyte. The fracture of the double layer tube was observed when NiO content in the fuel electrode exceeded 80 mol% for the 3 mol% YSZ, and when NiO content exceeded 50 % for the 8 mol% YSZ. The in situ observation of the sample during sintering and the SEM observation of the sample after sintering showed that the fracture occurred around 1200[degree]C owing to the sintering shrinkage. The cracking due to the difference in thermal expansion coefficient between the fuel electrode and the electrolyte was observed in the 8 mol% YSZ, while no cracking took place in the 3 mol% YSZ. 10 refs., 10 figs., 1 tab.

  9. Static rock splitter using shape memory alloy as pressure source. Keijo kioku gokin wo atsuryokugen to shita ganseki seiteki hasaiki ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, K.; Nishida, M. (Kumamoto University, Kumamoto (Japan). Faculty of Engineering); Inaba, T. (Nishimatsu Construction Co. Ltd., Tokyo (Japan)); Yamauchi, K. (Tokin Co., Tokyo (Japan))

    1991-12-25

    Rocks and concretes are split in urban areas or in the vicinity of important structures frequently in the recent years, where a process using blast-free hydraulic splitter or expansive splitter is used. This paper describes a basic study to utilize the recovery force of TiNi shape memory alloy as a pressure source. Experiments were carried out on TiNi alloy for its recovery force and deformation characteristics after a biaxial compressive deformation under various compositions and heat treatment conditions. As a result, it was found that within the range of the experiments the TI-60.5 Ni processed and heat treated material is most suitable as a pressure source under normal temperatures, and its maximum recovery force reaches 600 MPa. Giving considerations on the relation between crack developing conditions and loading angles in the case where a uniaxial compressive loading is performed on a bore hall drilled wall, a rock splitting device using TiNi was fabricated on a trial basis and experimented. The result showed that it has a splitting force capable to break ultra hard rocks with the maximum unit splitting force at 3-5 t/cm and the maximum stroke rate at 2-3%. The device has split the test rock specimens within several minutes. 17 refs., 15 figs., 1 tab.

  10. Study of ceramics having high heat impact resistance by applying the gradient composition technique; Keisha sosei shuho wo oyoshita kotainetsu shogekisei ceramics ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    When symmetrical gradient compositions like ceramics/metal/ceramics are adopted, composites having a large compressive residual stress in the surface ceramics layer can be fabricated. For the symmetrical gradient composition materials, such as Al2O3/TiC/Ni/TiC/Al2O3, it was clarified from the preliminary studies that their toughness was enhanced in 50 to 300%, their hardness in 10 to 20%, and their bending strength in 200 to 300% compared with the usual sintered alumina. In this study, such symmetrical gradient composition structures were designed and fabricated, to intend to enhance the ceramics in the surface layer. For the sintering process, the nitriding reaction heat of Si was utilized in the high pressure nitrogen gas, and the SHS/HIP method was applied, by which inhomogeneous materials with different sintering temperatures in individual parts can be sintered. The heat impact resistant properties of materials fabricated by this process were experimentally evaluated, and the thermal stress analysis was conducted to clarify the improvement mechanism of their heat impact resistant properties. Fundamental data were obtained, as to the development of super high temperature materials, which can be used stably even under the severe conditions. 13 refs., 36 figs., 10 tabs.

  11. Study of selective oxidation of methane catalyzed by solid superacid in unique reaction field; Tokushu hannoba no kotai chokyosan wo mochiiru methane no sentaku sanka hanno ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Misonoo, M.; Tatsumi, T.; Mizuno, T.; Inumaru, T. [The University of Tokyo, Tokyo (Japan)

    1997-02-01

    Selective oxidation of lower alkanes by use of heteropolymeric compounds is studied. Alkanes are activated on Cs2.5H0.5PW12O40 serving as catalyst, and their activity and selectivity improve when the catalyst is developed into a dual function catalyst in which Cs and Pt are combined. A success is reported of the synthesis of a heteropolymeric acid in which two molecules of the coordination element wolfram are replaced with a transition metal of the first period, on which acid the oxidation of cyclohexane is enhanced. Cs2.5Ni0.08H1.34PVMo11O40 as a metal/heteropolymeric acid dual function catalyst enables the direct oxidation (9% recovered at 340{degree}C) of isobutane into a methacrylic acid, which is attributed to the harmonious coordination of the oxidizing work of the catalyst and acidity. It is possible to oxidize propane into the acrylic acid, but not ethane into the acetic acid. In the case of Pd/Cs2.5H1.5PVMo11O40, the formic acid, methanol, etc., are produced upon addition of hydrogen to the system. This reaction in the hydrogen/oxygen system is supposed to take place via activated oxygen seeds as in the case of oxidation by hydrogen peroxide. 10 refs.

  12. Global sea level change and the response of solid earth; Kaisuijun hendo ni taisuru kotai chikyu no yakuwari

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    A review was given on the theory that sea level change having occurred in the past 20,000 years has given a great impact on patterns of upheaval and subsidence of the islands of Japan. Nakada has summarized distribution of underwater remains in the western part of Kyushu and estimated values of sea surface altitude in 6000 years ago, and used this conceptional chart to propose a crust upheaval mechanism by using hydroisostasy. More specifically, this is a model that crust which has subsided due to rise in the sea level has created flows of mantle, causing upheaval of the crust in land areas. This viewpoint requires further accumulation of data and verification of the theory in areas other than the western part of Kyushu. It is important to consider the effect of sea level change also in studying processes of subsidence and sedimentation in sedimentary basins including Osaka Bay. The currently available theories use analysis solutions on stratified ground, but does not consider topographical profiles from land areas to sea areas. As this topographical effect is thought extremely important, it is necessary to develop a two-dimensional cross section analyzing method by using the finite element method. 6 refs., 3 figs.

  13. Studies on silicon nitrides; Chikka keiso ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    Sinters of silicon nitrides have excellent properties as a structural material, but their technological repercussion effect is not as much as has been expected. The cause is in insufficient understanding on the mutual relationship between microstructures and mechanical properties. Therefore, methods of controlling structures were first discussed in the studies on synthesis of high-tenacity ceramics. In order to achieve high reliability in material strength, discussions were given on means to have a structure developed with high reproducibility. Development was performed on {beta} powder which shows no abnormal grain growth and is stable at elevated temperatures. Then, quantitative evaluation was made on factors to manifest a self-compounding structure with columnar particles grown in ultrafine particles. The relationship between its chemical composition, microstructure and mechanical properties was also discussed. Particle shapes of silicon carbides and their fracture tenacity values were considered theoretically by using a drawing model. To evaluate the microstructure, it is important to determine the grain boundary composition, whereas an electric field radiation type high-performance electron microscope was developed. In discussing the fracture mechanism, a model was structured for behavior of covalent binding crystals against external stress. 164 refs., 95 figs., 10 tabs.

  14. Study of white noise; Hakushoku zatsuon ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kano, R.; Tada, R. [Teikoku Oil Co. Ltd., Tokyo (Japan)

    1996-05-01

    A study was made on conditions available for white noise belonging to a finite power function with the use of a power spectrum conception. It was defined that a real variable function with a finite waveform energy was a finite energy function while that with a finite waveform power was a finite power function. A noncorrelative white noise was defined as a real variable function in which an autocorrelation function took a specific value at a certain point; however, the autocorrelation function was different between the finite energy function and the finite power function. In other words, the definition of white noise was such that `an energy spectrum was a fixed value` in the finite energy function, and that `a power spectrum was a fixed value` in the finite power function. It was pointed out, by Matsuyama (1994) with the use of the energy spectrum conception, that the white noise belonging to the finite energy function took only the form of `an arbitrary impulse function that all turned to zero except a certain point`. The same conclusion was obtained with respect to the white noise belonging to the finite power function. 1 ref., 1 tab.

  15. Study on jellyfish treatment. Kurage shori ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sakata, S.; Yoshinobu, N. (The Chugoku Electric Power Co. Inc., Hiroshima (Japan))

    1991-09-20

    Jellyfish assaulting in a great number during summer into water intakes at power plants is disposed of by land filling in plant premises. Discussions on treatment methods and tests using test machines have been carried out over four years to save disposition area and prevent odors. While it is well known that jellyfish melts in fresh water, the basic tests identified that heating and alkali treatment is effective, the fish shrinks and reduces rapidly when boiled to 80{degree}C or higher, it can be cut and crushed easily, and its solute has a high COD. A test machine having a treatment capacity of 5 tons an hour was used. The machine consists of a cutter unit, a supply pump, a draining box, a heating tank, a circulation pump and a mesh conveyer, and is capable of batch and continuous treatments. A full-size based test machine improved of transferring and solid treating functions was tested to a satisfactory result of achieving the initial intention. Installation of a full-size machine is under way. 12 figs., 8 tabs.

  16. Study on cobalt oxide; Sanka kobaruto ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-28

    This is No.91 report of National Institute for Research in Inorganic Materials, concerning cobalt oxide. For the growth of single crystal by the Czochralski method, shape of interface and contamination of impurities are affected by the convection of molten liquid in the atmosphere. Various oxides besides CoO were investigated. Solid solutions of Cr2O3 and Al2O3 into CoO were also studied. Non-linear optic and dielectric properties of single crystals, such as Ba2NaNb5O15 and LiNbO3, were examined. It was considered that the positive electron having positive electric charge can be used for the study on the negative electric charge defect in materials. However, the positive electron itself is rare, which results in the too low efficiency of measurement. Efficiency improvement of 50 times was achieved by introducing a high performance 2D position detector, which was still low efficiency of one-hundredth compared with photoelectron spectroscopy. It was found that the aggregation structure of positive ion defects in CoO is a misunderstanding of phenomenon caused by the electronic state in bulk crystals. As a result of the study on the optical properties of f-electron transition metals, transparent ceramics with addition of various rare earth ions were described. 162 refs., 106 figs., 14 tabs.

  17. Effect of massive transformation on formation of acicular structure in austenitic stainless steel weld metal solidified as ferritic single phase. Report 5. Study on solidification and subsequent transformation of Cr-Ni stainless steel weld metals; Feraito tanso de gyokosuru osutenaito kei sutenresu ko yosetsu kinzoku ni okeru ashikyura jo soshiki no keisei ni oyobosu masshibu hentai no eikyo.5. Cr-Ni kei sutenresu ko yosetsu kinzoku no gyoko/hentai ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, H.; Koseki, T.; Okita, S.; Fuji, M. [Nippon Steel Corp., Tokyo (Japan)

    1997-05-05

    The authors clarified that massive transformation occurs at two phase region under To temperature and there is K-S relation between the massive formation phase and base phase using {gamma} stainless steel that solidifies at F mode and forms acicular structure at room temperature structure. There is a possibility of massive transformation in weld metals because the cooling rate below the high temperature To was high even for normal welding process. Thereupon, in this report, whether the massive transformation effects the formation of acicular structure or not was studied as for {gamma} stainless steel weld metal that solidifies at F mode and room temperature structure becomes acicular form of two {delta} and {gamma} phase. As a result, it was clarified that massive transformation occurs at two phase region with temperature below To, and the room temperature structure was acicular form structure irrespective to massive transformation in case of composition with small Cr/Ni ratio even in case of stainless steel that solidifies at F mode. 20 refs., 15 figs., 1 tab.

  18. Investigation on food sanitation controlling technologies; Shokuhin eisei kanri gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Doi, Y. [Hokkaido Electric Power Co. Inc., Sapporo (Japan); Nishioka, J.

    2000-03-24

    Investigation has been made on the current status of food sanitation controlling technologies. Eighty percent of food poisoning is caused by bacte such as Salmonera, enteritis vibrio, staphylococcus, and pathogenic colibacillus. Putrefaction as the cause for food poisoning occurs from proliferation of different microorganisms. Heating sterilization is the main method being performed, but non-heating method may include sterilization by flash and high voltage pulse discharge in addition to ultra-high pressure and ultraviolet ray sterilization. As a result of the questionnaire survey, what is extracted as the problems in the food sanitation controlling technologies is to establish a rinsing and sterilizing method with large sterilization effect, an effective sterilizing method and thawing of processed marine products, and a cooling method in food processing. Increasingly demanded for the future is to develop a foodstuff sanitation control system using as the core the hazard analysis critical control point (HACCP, a quality control program developed by the U.S. NASA to ensure safety in manufacturing space food), and micro-organism control and sterilizing technologies to support the above system. The flash pulse and high-voltage pulse sterilizing technologies as the non-heating sterilizing technology are more effective than the conventional heating sterilization methods also from the aspect of quality retention after sterilization. More active development thereof is desired. (NEDO)

  19. Proceedings of RITE international workshop on valuation; Total eko balance ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The RITE International Workshop on Valuation was held in Tokyo and Osaka in February 1996, and eight papers on total ecobalance were reported. In The Field of Impact Assessment, described were constitution and methodology about impact assessment in a wide sense. In LCA Yesterday, Today and Tomorrow, discussed were the historical development and future outlook of LCA. In Standardization of Product Life Cycle Assessment, a survey of the present situation of LCA international standardization was made. In the Relationship between Product Life Cycle Assessment Methodology, considered was the relationship between the goal definition of the product life cycle assessment and the methodological choices. In Valuation in LCA, the present study of LCA was reviewed. Besides, reviews of the LCA study in Japan were made public.

  20. Study on intelligent structural materials; Intelligent kozo zairyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-28

    Materials having intelligent properties against fracturing were investigated. Synthesis of materials with high toughness, understanding of elementary process of fracturing, and investigation of intelligent structural materials were selected as research themes. For the experiments, relationship was examined between fracture resistance and crack propagation of the highly tough silicon nitride produced by the newly developed texture control method. As a result, it was found that the crack propagation of this material can be detected by abnormally grown grains, and that the resistance against fracturing increases with crack propagation. It was revealed that the present material is a crack diagnostic intelligent material. The crack edge of these liquid phase sintered materials with high toughness is very active. The cracks can be recovered below the sintering temperature. This means that the strength can be recovered by the proper heat treatment on the way of use. The reliability can be secured by the different method from the conventional investigation aiming at high performance. 140 refs., 82 figs., 8 tabs.

  1. Investigation research on autonomous responsive materials; Jiritsu oto zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was made on autonomous responsive materials as a new material which reversibly change molecular structures and the aggregation state according to external stimuli. Autonomous responsive materials imitate environmental responsibility in the living organism system and have sensing, control and active functions for external stimuli. The materials are highly efficient and environmentally friendly. In biomimetic materials for soft actuators, drastic changes by temperature of elastic modulus of water-swollen hydrogel are used to the motion. In order to molecularly design stimulus-responsible polymer gel, studied are the relation between the micro structure and stimulus responsibility, dynamic correlation between the micro structure and the macro structure, etc. In the biomedical field, new cure and diagnosis using innovative materials are expected, and the application of autonomous responsive materials to the field is studied. For example, using hydrogel responding the temperature and the surface and controlling by temperature the interaction with components of the organism such as protein and cells, drug delivery in the organism is optimized. Also studied is the application of hydrophilic/hydrophobic changes by temperature to the chromatography. 215 refs., 47 figs., 11 tabs.

  2. Systematic analysis on mooring systems of floating structures; Futai keiryuho ni kansuru keitoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, K.; Suzuki, H.; Ide, T. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    Discussed herein are mooring performance requirements of the new types of marine structures now proposed, and characteristic ranges and future expansion potential of the existing mooring systems. The mooring systems studied for floating structures are catenary, single point (multi-leg and single-leg types), fixed structure with fender and tension leg mooring systems. The studied items include extraction of the elements that constitute rigidity of the spring for horizontal mooring, survey on and data collection for each element, determination of element ranges, programs for mooring analysis, assessment of mooring characteristic ranges, and potential development of the characteristic ranges. It is concluded that the existing systems with their current characteristic ranges and future possibility are insufficient for the future marine structures. It is therefore necessary to develop new mooring concepts, instead of expanding the current concepts, in order to meet the mooring performance requirements for the new marine structures. 14 refs., 9 figs., 11 tabs.

  3. Measuring techniques for martensitic transformations; Marutensaito hentai ni kansuru sokutei gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Murakami, Y.; Morito, S. [Univ. of Tsukuba, Tsukuba (Japan). Graduate School; Otsuka, K. [Univ. of Tsukuba, Ibaraki (Japan). Inst. of Materials Science

    1996-03-20

    It is better to measure physical amount that shows significant change during transformation in order to carry out precise detection of martensitic transformations or to decide the transformation temperature. One of it is Differential scanning calorimetry (DSC) method. This method is very easy along with the determination of transformation enthalpy and also specific heat and is used widely. In martensitic transformation, there exist the intrinsic crystal habit face to the alloy system and crystal azimuthal relation between parent phase and martensite, and it is important to decide them correctly as crystallographic parameters. Overhere, method for measuring crystallographic parameters from martensite caused in parent phase single crystal material is introduced. Further, role of electron microscope is extremely large regarding the revelation of martensitic transformation mechanism in atomic scale. In this report, as for what is revealed regarding martensitic transformation when using electron microscope, crystal structure of martensite, form, structure of the interface and so forth are cited. 39 refs., 5 figs.

  4. Recent surveys and researches on pollinosis in Japan; Kafunsho ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shido, T. [The Inst. of Public Health, Tokyo (Japan)

    1998-05-31

    In this paper, recent investigations and researches on pollinosis are summarized as centering on the investigation entrusted by the Ministry of Health and Welfare and executed since 1992, and especially the surveys on Japanese cedar pollinosis during 1995 to 1996. The quantity of pollen surveyed in 1995 is the greatest in the survey history of nationwide flying pollen. Particularly, the quantity of cedar and hinoki pollen is 10 to 40 times as many as that in the year before. Consequently, since the sensitization and onset due to the cedar pollen increased greatly, the objects of the surveys and the researches were mainly in respect to the analysis of onset factors of pollinosis, clarification of its natural process, evaluation on the effectiveness of desensitization therapy, the clinical subjects including the confirmation of pharynx symptom and asthma symptom, and the discovery of naturally sensitizing dog. A fact that the quantity of flying pollen concerns the occurrence and degree of the clinical symptom has already been indicated by a clinical observation carried out for a long period of time. In respect to specific prophylaxis and therapy, for the first time the pollen masks and glasses sold on the market are investigated, and the necessity of the verification thereof is described. 27 refs., 7 figs., 5 tabs.

  5. Research on harmonized molecular materials; Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Harmonized molecular materials (HMM) were researched to create functional materials adaptable to needs such as environmental harmony and high-efficient conversion in post-industrial society and aging society. Superior mechanisms function efficiently in organisms for perception, transmission and processing of information, and transport and conversion of substances. These functions are caused by harmonization between organic molecules, or organic molecule and metal or inorganic substance. HMM is a key substance to realize these functions similar to those of organisms artificially. It is the purpose of this research to develop HMMs, reform production process by innovating separation and conversion technologies, and finally realize molecular chemical plants. This research also develops high-efficient devices to contribute to the information society, and progresses the industry of bio-functional materials such as high-sensitive bio-sensor. The functions, applications and creation technologies of three kinds of HMM such as assembly, mesophase and microporous materials were researched in fiscal 1995. 956 refs., 128 figs., 13 tabs.

  6. Research study on harmonized molecular materials (HMM); Bunshi kyocho zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As functional material to satisfy various needs for environmental harmonization and efficient conversion for information-oriented and aging societies, HMM were surveyed. Living bodies effectively carry out transmission/processing of information, and transport/conversion of substances, and these functions are based on harmonization between organic molecules, and between those and metal or inorganic ones. HMM is a key substance to artificially realize these bio-related functions. Its R & D aims at (1) Making a breakthrough in production process based on innovation of material separation/conversion technology, (2) Contribution to an information-oriented society by high-efficiency devices, and (3) Growth of a functional bio-material industry. HMM is classified into three categories: (1) Assembly materials such as organic ultra-thin films (LB film, self-organizing film), and organic/inorganic hybrid materials for optoelectronics, sensors and devices, (2) Mesophase materials such as functional separation membrane and photo-conductive material, and (3) Microporous materials such as synthetic catalyst using guest/host materials. 571 refs., 88 figs., 21 tabs.

  7. Carbon dioxide fixation in green plants; Shokubutsu no tansan gas kotei ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Onishi, S. [Kansai Electric Power Co. Inc., Osaka (Japan); Kiyota, M. [University of Osaka Prefecture, Osaka (Japan); Nishimura, M. [Kansai Tech Co., Osaka (Japan)

    1997-09-30

    Concerning the effects of carbon dioxide whose level of concentration is on the rise, the short-term effect that works on the amount of exchanged gas and the long-term effect that works on the growth of green plants are studied by use of several kinds of green plants. Changes in the carbon dioxide absorption rate (photosynthetic rate) in saplings in the wake of a rise in carbon dioxide concentration are studied, and it is found that a rise in carbon dioxide concentration results in an increase in the photosynthetic rate and that the rate rises with an increase in the intensity of light. The effect of temperature is stronger when concentration is higher, with the temperature suitable for photosynthesis moving toward the high-temperature side. Growth is investigated of seedlings of Acacia mangium two years after transplantation, and then it is found that seedlings in the 1000ppm carbon dioxide section are greater by 20% in height and by 30% in trunk diameter than those in the 350ppm carbon dioxide section. In addition, the total dry matter weight is heavier by 82%. As for dry matter accumulation, there are noticeable amounts in the branches, trunks, and roots, while there is but a 15% increase in the leaf area. Leaves fall early in the high carbon dioxide environment, and this is supposedly the cause for a slowdown in the rate of the increase of photosynthesis. 6 refs., 7 figs., 2 tabs.

  8. Relationship between stacking process and resolution; Jugo shori to bunkaino ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J.; Rokugawa, S.; Kato, Y. [Geological Survey of Japan, Tsukuba (Japan); Yokota, T.; Miyazaki, T. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1996-10-01

    This paper evaluates influences of stacking of incident angles against the reflecting surface on the resolution. Basic equations for evaluating the influences were deduced. A simple evaluation method has been provided using these equations. The present evaluation method is considered to be useful for acquisition design, processing, and interpretation of data as an indicator. According to the equations introduced in this study, there are some demerits for stacking traces whose incident angles were large. A total reflection region often appears due to the decreased resolution, and the vertical resolution decreases prior to stacking. Occasionally, it is not effective to remove traces having large incident angles from the viewpoint of resolution. In practice, the selection of most suitable trace through trial and error is not easy due to difference in individual regions. An evaluation method must be discussed, by which the optimal trace can be selected automatically during the data processing. 6 refs., 15 figs.

  9. Survey on commercial use of fuel cells; Nenryo denchi ni kansuru jitsuyoka no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The basic survey was carried out for the future approach to R & D of fuel cells. Phosphoric acid fuel cell (PAFC) is in the stage of demonstration research and field test supported by subsidy after the end of Sunshine project. Its reliability and durability problems are being solved, and its cost reduction is only one problem for practical use. Distributed systems or on-site systems will be used utilizing its excellent environmental characteristics. Molten carbonate fuel cell (MCFC), solid oxide one (SOFC) and polymer electrolyte one (PEFC) under development were thus surveyed. The following are surveyed: (1) Contribution to a human society such as improvement of energy demand/supply structure and environmental protection, (2) Technological items such as outlook for R & D, validity of developmental issues, comparison between various R & D and significance in industrial promotion, (3) Economic items such as profitability and feasible period, and (4) Social items such as sociability, compatibility to needs, possibility of locations, international meaning, market scale and promotion scenario. 90 refs., 67 figs., 96 tabs.

  10. Layered multinary lanthanum oxide [La-Mo-O]; Sojo rantan fukugo sankabutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    Studies have been carried out systematically on properties of oxides including representative transition metal, vanadium, and alkali metals. With respect to Ln2CuO4 (Ln is a rare earth element) being a simple and representative rare earth multinary oxide showing superconductivity, and its related compounds, this paper reports thermal chemistry, superconduction, and making them a superconductor by using soft chemical treatment. The paper also reports centrally on synthesis of new copper oxide superconductors under high pressure, the compositions, structures, superconductive properties of the synthetics, and the relationship between them. It describes phase equilibrium, synthesis, and structures of vanadium multinary oxides being the object of continued studies, and also reports the studies related to structure and phase transfer of NaV6O11 which shows especially interesting properties among the oxides. Studies have also been made on NMR of these compounds and copper oxide superconductors by using magnetic resonance. The paper also describes a method to analyze the structure of quasi-crystal having rotary symmetry which is not allowed in crystals, and has special long-distance order phase. 209 refs., 127 figs., 6 tabs.

  11. Medical chemical engineering the research; Iyo kagaku kogaku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sakai, Kiyotaka [Waseda University, Tokyo (Japan)

    1999-03-05

    He taking the chemical-engineering technique as a weapon, it participates in research and education over the perennial in the field of medical chemical engineering, medical engineering, bioengineering, and the excellent research result has been raised. Moreover, leading research result is raised in these research field which are the interdisciplinary field between medicine and chemical engineering, and the considerable contribution in these fields has been done. He enables the new development of the dialysis technology by advancing the research first of all from the viewpoint of hemodialysis film, hemodialyzer and three of the patient pharmacokinetics, in respect of dialysis technology in the artificial kidney, and developing the original dialysis system enables optimum dialysis treatment. Next, he on the oxygen which is the feed which is the most important for the organism, it originally crosses, and the gas is run in figuring hollow yarn lattice in the hollow yarn inside, and it is clarified that the system for washing the blood outside is advantageous, and it has succeeded in the development of the more efficient artificial lung. And, the artificial gill is examined from the original idea, which takes in the oxygen by using of a film in the oxygen carrier (the substitution blood), as intermediary. Next, he some of the phenomenon in the blood plasma viscosity of patient with renal failure or are measured and the relationship between blood plasma viscosity and disease state is clarified, and the knowledge which is useful for the diagnosis has been obtained. And, it is examined that the quantity that the hydrophobic drug is adsorbed in the albumin differs in normal subject and dialysis patient, and the system for deciding chemical administration quantity to the dialysis patient is being found. Next, in research progress of the above, various measuring technique are devised, and remarkably the research advances. For example, the considerable contribution for measurement of diffuse transmission coefficient of hollow yarn dialysis membrane by the optical measurement technology, glucose using the electrochemiluminescence and immunisation center, this advance on development of the continuous measurement method of the endotoxin, etc. of the research of the direction more and more has been done. In the interdisciplinary field of medical chemical engineering and biochemistry engineering, chemical engineering such as the bioengineering as an importance, he will apply chemical-engineering technique, approach in future more and more, while the above, he make the chemical engineering association to be a basis of the activity, many-sided, and various creative research result have been raised, and the result has been evaluated high in domestic and overseas. (translated by NEDO)

  12. Consideration on corrosion fatigue crack life assessment; Fushoku hiro kiretsu hassei jumyo hyoka ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, H.; Yamamoto, M.; Saito, T. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Morita, K. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-10-01

    Discussions were given on corrosion fatigue crack life by using corrosion fatigue crack initiation test and analysis. The test used 13Cr-based stainless steel as a test material, and aquamarine at 60{degree}C as a corrosion environment. The fatigue test was performed under a tension loading condition with a stress ratio of 0.1 and an iterative velocity of 1.7 Hz by using a 10-tonf fatigue testing machine. In the corrosion fatigue crack initiation test, a pit has been generated on a boundary of an exposed part and a painted part for masking, hence direct observation was impossible on pit growth behavior. Therefore, an intrinsic crack model was introduced from pit dimensions as observed from a fracture face, and analysis was made on corrosion fatigue crack growth by using the linear fracture dynamics, wherein clarification was made on a phenomenon occurring after the crack growth passes the pit growth until the test piece is fractured. A proposal was made to define the time when fatigue crack initiates and grows from the bottom of a pit as a result of surpassing the growth of corrosion pit as the corrosion fatigue crack life. 4 refs., 7 figs., 1 tab.

  13. Study on development of adsorbent of acetaldehyde; Acetaldehyde yo kyuchakuzai no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Noda, T. [Nippon Steel Corp., Tokyo (Japan); Suzuki, M. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science

    1997-07-10

    The adsorption of acetaldehyde by porous ceramics impregnated with hydrazinium aluminum sulfate (HAS) is studied. Silicagel, activated alumina, activated clay, and activated carbon are compared, and it is found that silicagel and activated clay are suitable as a substrate for HAS impregnated adsorbent. The adsorption mechanism of acetaldehyde by the adsorbent is believed to be one in which acetaldehyde reacts with hydrazinium and yields acetaldazine. The adsorption capacity of the adsorbent at low acetaldehyde concentration of 0.1 ppm was as large as 1.36 mol/kg. This adsorption capacity at 0.1 ppm acetaldehyde concentration is remarkably larger than that of conventional activated carbon. Hydrazinium decomposes easily in the air because it is a strong reducing agent and reacts with oxygen or carbon dioxide. But hydrazinium impregnated on porous ceramics with HAS becomes more stable and maintains reactivity with acetaldehyde for longer than six months. An adsorbent made of porous ceramics impregnated with HAS is useful as a deodorant for acetaldehyde. 8 refs., 6 figs., 6 tabs.

  14. Study of freshwater red tide control measures; Tansui akashio taisaku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Onishi, M.; Hatamochi, K. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1997-09-30

    Basic research of biological measures for which the accumulation of basic findings is mandatory and the applied research of chemical and physical measures that are higher in feasibility are conducted for the establishment of measures to counter freshwater red tides. In the basic research, natural enemies, algaecidal microbes, conjugation inhibiting substances, and allelopathy are studied, but none of them is found feasible at the current stage. In the basic research, however, factors are discovered that inhibit the multiplication of Peridinium bipes or perish the same. In the applied research, chemical algaecidal methods, UV-aided algaecidal methods, and various red-tide constituent collection methods are studied. Collection methods are compared, and it is concluded that a method of Toray Industries, Inc., efficiently collects red-tide constituents. In this method, red-tide constituents are screened by and condensed on a cloth filter provided on the internal wall of a drum, and are dehydrated and then transferred. The applied research further involves the prediction of red tide outbreak and the raising of fish on a food containing substances extracted from red tides, and it is suggested that these are feasible. 18 refs., 15 figs., 3 tabs.

  15. Research on coal ashes treatment technology. Sekitan bai shori gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Masao; Hotari, Matajuro; Tokuda, Hitoshi; Eto, Yoshitake (Kyushu Electric Power Co., Inc., Fukuoka (Japan))

    1989-03-30

    Effective utilization and reclamation treatment of coal ashs of about 20% in quantity of coal which is produced by coal burning, become big problem. In order to research the treatment technology for coal ashs, the fundamental experiment in laboratory and ash treatment experiment on site were conducted by bench test for two years from the 1987 to 1988 fiscal year, and foundation characteristics of high density slurry, its environmental property, an selection of equipment such as mixer and pump were studied. The high density slurry system is a method that coal ashs are mixed with water at about 40-50% moisture content, placed into undersea and reclaimed. The result of the high density slurry system showed that density was about 10% larger in the value than that of dry system and the density of slurry was much affected by moisture content, and that the lower moisture content at the placing was, the larger moisture content was after the placing. the system was superior in strength and environmental property than those of conventional system, then its availability was able to be confirmed and verified. 9 refs., 71 figs., 15 tabs.

  16. Basic study on intelligent materialization of glass; Glass no intelligent ko zairyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    This is the report No. 98 issued by the Inorganic Material Research Institute. An intelligent material is a substance and/or material which responds intelligently to environmental conditions and exhibits functions. One of the features of amorphous materials including amorphous glass is a large freedom in chemical composition. These materials maintain order in short distance, but have as a whole the turbulent and specific atom orientation. Therefore, high tolerability in selecting the composition, and diverse synthesizing methods are available. A wide range of utilization may be conceived, such as introduction of the state of electrons having different valences in a structure, and the diverse chemical combinations. Patterns of existence of polyhedrons having different orientations, and how they are connected correlate closely with an external environment. Intelligent materials have high freedom against change in the external environment and are suitable to exhibit intelligent functions. Setting heat and light as the external conditions, attempts have been made on search and creation of intelligent materials based on state change induced by interactions between the two factors. Fundamental studies have been made on synthesis of different environment responding glasses and films, and on factors and phenomena for exhibition of the intelligence. 62 refs., 91 figs., 8 tabs.

  17. Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

  18. Investigation into the emission of greenhouse effect gases; Onshitsu koka gas no haishutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper grasped the situation of greenhouse effect gas emissions of advanced countries based on the reports from them. The advanced countries which concluded the U.N. Framework Convention on Climate Change (OECD member countries, the former U.S.S.R., and East European countries) are to be reported to the office concerned with work for the framework the situation of their greenhouse effect gas emissions according to the obligation of the framework. In and after April 1997, they made the second report. The paper summarized changes in emission amount, the future trend, and the policies/measures mainly taken of nine countries which have already presented the second report (the U.S., the U.K., Germany, Holland, Italy, Norway, Sweden, Finland, and New Zealand) and one country (Russia) which has made only the first report. Moreover, the literature was collected and summed up concerning the mechanism and coefficients of the emission of nitrous oxide and methane. The collected literature was classified into all fields/plural number of fields, energy relation, industrial process relation, relation with the use of organic solvent and other products, agricultural relation, relation with changes in land use and forests, and waste relation. 4 figs., 228 tabs.

  19. Studies on ternary silver sulfides; Fukugo gin ryukabutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    Some sulfides containing silver show high ion mobility based on movability of silver, whose application is expected. Studies have been carried out centrally on synthesis of new compounds of ternary silver sulfides by elucidating the relationship among their compositions, structures and properties by means of crystal chemical studies mainly on their phase relationship. A few new compounds have been synthesized, such as the ones having the argyrodite family compound structure including transition metals. The synthesizing process takes a kind of turbulent liquid state structure at elevated temperatures because of movability of silver, but silver is fixed at low temperatures in different sites between skeleton structures made by other atoms. These studies on phase transfer, structures, and silver movability have been based on X-ray diffraction, infrared and Raman spectroscopic measurements, NMR, measurements of electric and thermal characteristics. For the studies related to compositions and structures of ternary metal sulfides which take compound crystalline structure, a structure analyzing method based on multi-dimensional hyperspatial groups was used. This paper reports the summary of the studies in seven chapters, and dwells on the remaining problems and future prospects. 158 refs., 114 figs., 65 tabs.

  20. Studies of coal slurries property; Slurry no seijo ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Kawabata, M.; Aihara, Y.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Sakaki, T.; Shibata, M.; Hirosue, H. [Kyushu National Industrial Research Institute, Saga (Japan)

    1996-10-28

    It was previously found that the increase of slurry temperature provides a significant effect of slurry viscosity reduction for the coal slurry with high concentration of 50 wt%. To investigate the detailed influence of slurry temperature for the coal slurry with concentration of 50 wt%, influence of temperature on the successive change of apparent viscosity was observed at the constant shear rate. When the concentration of coal was increased from 45 wt% to 50 wt%, viscosity of the slurry was rapidly increased. When heated above 70{degree}C, the apparent viscosity decreased during heating to the given temperature, but it increased successively after reaching to the given temperature. The apparent viscosity showed higher value than that of the initial viscosity. The coal slurry with concentration of 50 wt% showed the fluidity of Newtonian fluid at the lower shear rate region, but showed the fluidity of pseudo-plastic fluid at the higher shear rate region. The slurry having high apparent viscosity by the successive change showed higher apparent viscosity with increasing the higher even by changing the shear rate. 1 ref., 4 figs.

  1. Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

  2. Catalytic activity of pyrite for coal liquefaction reaction; Tennen pyrite no shokubai seino ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Hirano, K.; Kozu, M.; Okada, T.; Kobayashi, M. [Nippon Coal Oil Co. Ltd., Tokyo (Japan)

    1996-10-28

    Since natural pyrite is easy to obtain and cheap as coal liquefaction catalyst, it is to be used for the 150 t/d scale NEDOL process bituminous coal liquefaction pilot plant. NEDO and NCOL have investigated the improvement of catalytic activity of pulverized natural pyrite for enhancing performance and economy of the NEDOL process. In this study, coal liquefaction tests were conducted using natural pyrite catalyst pulverized by dry-type bowl mill under nitrogen atmosphere. Mechanism of catalytic reaction of the natural pyrite was discussed from relations between properties of the catalyst and liquefaction product. The natural pyrite provided an activity to transfer gaseous hydrogen into the liquefaction product. It was considered that pulverized pyrite promotes the hydrogenation reaction of asphaltene because pulverization increases its contact rate with reactant and the amount of active points on its surface. It was inferred that catalytic activity of pyrite is affected greatly by the chemical state of Fe and S on its surface. 3 refs., 4 figs., 1 tab.

  3. Research on crystal growth by using pressure as a control parameter; Atsuryoku seigyo ni yoru kessho seicho ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-31

    This research project aims to establish a technique for crystal growth using pressure as a principal control parameter, and combining it with a microgravity condition, to develop a novel process material fabrication. Since the solubility of materials depends on pressure, it is possible to control a supersaturated condition for crystal growth by changing pressure. The growth condition can be controlled precisely, which is not possible by conventional methods that vary temperature and other factors. On the other hand, because a concentration diffusing field is formed autonomically around crystals in association with their growth, density convection is generated under gravity as a result of difference in the concentrations, making the growth conditions severely complex and uncontrollable. Ideal crystal growth condition control may be possible if the pressure control is performed under micro-gravity by which generation of the density convection can be suppressed. Realization has been achieved on in-situ observation by using high-magnification microscope which uses a diamond anvil cell, development of a hydraulic type optic pressure cell, and a high- speed crystal growing technology by means of pressure control utilizing the cell. New findings were also obtained on effects of pressure on crystal forms, and the pressure induced solid phase transfer mechanism. 67 refs., 49 figs., 3 tabs.

  4. Research on environmental bioecosensing technology using ecological information; Seitaikei joho ni yoru kankyo bio eco sensing gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The bioecosensing technology was studied which detects and identifies feeble signals generated by biosystem communication in wide biological environment. The following were reported as current notable environmental biosensing technologies: a quick measurement method of environmental contaminants using immunological measurement method, analysis method of ecological state of microorganism using DNA probes, observation of ecosystem by bioluminescent system, measurement method of environmental changes and contaminants using higher animals and plants, and detection method of chemical contaminants using chemotaxis of microorganism. As a result, the new bioecosensing/monitoring technology in molecular level was suggested for identifying comprehensive environmental changes which could not be measured by previous physical and chemical methods, as changes in ecosystem corresponding to environmental changes. As the wide area remote sensing technology of environmental ecological information, sensing technology on the earth, aircraft and satellite was also discussed. 247 refs., 55 figs., 17 tabs.

  5. Fundamental study that produce hydrogen with solar enregy. ; Property with simulated power source. Taiyo energy ni yoru suiso seizo ni kansuru kiso kenkyu. ; Mogi dengen ni yoru tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ota, H.; Aoki, Y.; Tani, T. (Science University of Tokyo, Tokyo (Japan). Faculty of Engineering)

    1990-12-06

    Mankind is currently confronted by several environmental problems. Among these problems are depletion of fossil fuel reseves, and global warming caused by CO {sub 2} and the consequent environmental damage. These problems demand the most serious consideration and solution. Fuel cell systems are one of the prospective energy systems. Fuel cell systems produce electricity electrochemically, and they produce it most efficiently, and with almost a complete absence of emissions. This basic study concerns the production of hydrogen. Hydrogen is the fuel used by fuel cells. Hydrogen is produced by the electrolysis of water with solar energy. In this paper, as a first step, the hydrogen generator {prime} s properties are measured. These properties are measured by supplying electricity both continuously and intermittently from a DC power source which simulates photovoltaic modules. Our conclusion is that, in the near future, utilization of a hydrogen generator may be feasible if electricity is supplied from photovoltaic modules. 3 refs., 12 figs., 2 tabs.

  6. New finite element method for thermal fluid flows at high Reynolds numbers; Netsuido ni tomonau ranryu no kaiseki ni tekishita yugen yosoho ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanahashi, T.; Nakai, T. [Keio University, Tokyo (Japan). Faculty of Engineering

    1995-12-15

    Generally speaking, finite element methods in the computational fluid dynamics are universal, but not economical. In the present paper in order to overcome this defect ill FEM, we propose a new method using the discrete del operator which is a coordinate-free differential operator in the discrete space. This operator in the discrete space is defined as an element average of the gradient of the shape function and it has three characteristics such as orthogonality, identity and symmetricity. Furthermore the discrete del operator is useful in non-memorizing and in easy coding. As the analytical expression of the discrete del operator is a vector in the two or three dimensions, the natural description of programming becomes objective and compact, which is more understandable for non-specialists of CFD. Here we apply this method to thermal fluid flows at high Reynolds numbers. 10 refs., 5 figs., 1 tab.

  7. Report on research results of the development of high efficient boilers in fiscal 1996. Research development of high efficient industrial furnaces, etc; Koseino boiler no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Out of the developments of high efficient boilers which have been continued since fiscal 1993, the paper reported the result of the development conducted in fiscal 1996. The oxygen combustion (the oxygen enrichment combustion including 100% oxygen combustion) decreases the amount of flue gas and reduces heat loss of the flue gas, and is also effective as NOx reduction measures. The experiment was conducted using testing furnace. The boiler efficiency rapidly increased with the increasing concentration of oxygen enrichment. In the pure oxygen combustion, the overall boiler efficiency of a 106% level (low heating value standard) is expected. Since the boiler wet flue gas is decreased, the NOx emission is reduced. The boiler can raise the combustion temperature with no fear of NOx and can be reduced in size. CO2 decreases in proportion to the energy saving effect. The development of a condensation flue gas heat exchanger is aimed at recovering heat down to the low temperature. Prediction of heat transfer in the steam condensation region becomes possible, and the size reduction can be expected. Dew point corrosion resistant materials were also selected. As to the high speed combustion control, a simple type using micro-processor was developed. Obtained were high speed, compactness, electric power saving, and high controllability. 14 refs., 306 figs., 88 tabs.

  8. Especially the research-biochemistry engineering bioprocess system the research various new development research; Seibutsu kagau kogaku ni kansuru kenkyu-tokuni baio purosesu shisutemu no chinoka ni kansuru kenkyu oyobi shujuno shinki baio riakuta no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, Isamu [The Institute of Physical and Chemical Research, Tokyo (Japan)

    1999-03-05

    The biochemistry engineering, especially research on the intellectualisation of the bioprocess system and development researches of various new bioreactors, is done, and the achievement, which it is very much excellent, is being held. And, function and structure of the new photoreaction enzyme were clarified, and the way of the new sensor development was shown. The achievement can be divided roughly into next three. The research on the intellectualisation of the bioprocess system: Various metabolism activity shown at cellular level of the industry microorganism was estimated in on-line real time, and the computer control system which controlled the process based on physical state of the microorganism was developed. Microorganism concentration laser turbidity sensor, substrate using the ceramic sampler and metabolism product concentration measurements systems, sample liquid automatic transfer line system have been used practically even in the inside in laboratory, factory. In addition, this system developed, and anomaly diagnosis system by the expert system was constructed. And, the maintenance system of next generation bio plant which introduced group intelligent robot is being developed. The development of the new bioreactor: The conventional agitation tank type bioreactor developed, and what is called various new separate type bioreactors in which the biological response could also process the separation of the purpose product simultaneously and concurrently by the identical container were developed. It is a fluidized-bedding bioreactor that the microorganism is made to adhere to porous tube type bioreactor and die child state polyurethane foam which constitute the ceramic filter tube center and that the flow makes it react, and as, drums solid culture reactor-using the polyurethane foam, etc. are them. The utilization is respectively examined these and new bioreactor for apple wine and antibiotics, production of the industrial use enzyme. The research on the correlation between structure and function of the photoresponsivity nitrile-hydratase: It was found that it studied structure and function of photoresponsivity nitrile-hydratase which converts into the amidation conjunction thing with the hydration of the nitryl compound and clarifies the molecular structure of reaction center, and that NO controls the photoactivation. This discovery opens the way for the development of the again new NO sensor. Like this, the result has been evaluated him high using much excellent achievement in the field of the biochemistry engineering in domestic and overseas. (translated by NEDO)

  9. FY 1999 report on the results of the R and D on high performance industrial furnace, etc.; 1999 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the development of high performance industrial furnace, initial targets were achieved such as energy saving of 30%, downsizing of 20%, and a remarkable NOx reduction. To verify the achievement, the test field project is being worked on by NEDO. In FY 1998, 23 heating furnaces, 29 heat treat furnaces and 6 melting furnaces were under the project at energy saving effect of 52,000 kl converted to crude oil. In FY 1999, 18 heating furnaces, 26 heat treat furnaces and 7 melting furnaces are now under the project at energy saving effect of 57,000 kl. The project was awarded 'The 9th Nikkei Global Environmental Technology Prize.' The themes for the R and D are as follows: high efficiency exhaust heat utilization system, self-completion type high temperature/high radiation heating technology, technology to make heat transfer in steel heating suitable under non-stationary state, high efficiency heat transfer technology, technology to optimize the shape of heating furnace, high performance atmosphere heat treat furnace, high efficiency heat transfer technology by high temperature jet flame heating, technology of high efficiency aluminum melting furnace, technology to improve soaking degree in steel heating, high performance tubular heating furnace in oil refining, optimum combustion control technology of regenerative burner furnace, and laser measuring method inside industrial furnace. (NEDO)

  10. Fiscal 1998 research report on development of the advanced industrial furnace (R and D on the advanced industrial furnace). Volume 3; 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the research results of the chapter 4 and 5 (experimental database) from the research report on development of the advanced industrial furnace. The chapter 4 summarizes functions of the temperature performance evaluation simulator of the advanced continuous heating furnace for the database system, and various research results obtained by the simulator. This chapter also summarizes the research result on the applicability of high-temperature air combustion to other industries, the patent research result on heat storage combustion technology, the basic technology research result, and the reaction analysis result by FLUENT. The chapter 5 summarizes the combustion experiment data collection by developing self-completion high-temperature high-radiation heating technology. As for R and D on technology optimizing the profile of heating furnaces, the following data are summarized: measurement data of heat transfer in furnaces and heat flux data at right overhead furnace temperature under cold air and preheated air combustion in conventional furnaces, and heat storage combustion. (NEDO)

  11. Study on automatic tuning of ship`s PID regulators; Hakuyo seigyo system no gain jido chosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakatani, T. [Toyama Mercantile Marine College, Toyama (Japan); Otsu, K.; Moriyoshi, N. [Tokyo Univ. of Mercantile Marine, Tokyo (Japan); Okazaki, T. [Nagoya Institute of Technology, Nagoya (Japan)

    1996-12-31

    Proportional, integral and derivative (PID) controls are used for a steering system and a main engine control unit installed in a vessel. Among them, this paper describes effectiveness of a PID gain tuning method using a limit cycle by means of relay control which is safer and simpler than conventional limit sensitivity methods. The present method was applied to an actual marine control system to conduct an actual vessel experiment. As a result of applying the method to a bow azimuth control system using a rudder, a new azimuth setting was set with an overshoot of 1.6 degrees in a ten-degree azimuth changing experiment. With respect to direction maintaining steering performance, the present method was capable of controlling the direction at a speed loss to about 80% of the ship`s autopilot. As a result of applying the method to a bow azimuth control system using a bow thruster, direction maintaining and changing control was realized in a low speed range in which rudder effect is lost. As a result of applying it to a main engine governor system and performing control of main engine rotation speed, it was found possible to derive control gains in a safe state without applying an excessive load to the main engine both under load and no load conditions. 14 refs., 8 figs., 11 tabs.

  12. Study on molecular controlled mining system of methane hydrate; Methane hydrate no bunshi seigyo mining ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kuriyagawa, M.; Saito, T.; Kobayashi, H.; Karasawa, H.; Kiyono , F.; Nagaoki, R.; Yamamoto, Y.; Komai, T.; Haneda, H.; Takahashi, Y. [National Institute for Resources and Environment, Tsukuba (Japan); Nada, H. [Science and Technology Agency, Tokyo (Japan)

    1997-02-01

    Basic studies are conducted for the collection of methane from the methane hydrate that exists at levels deeper than 500m in the sea. The relationship between the hydrate generation mechanism and water cluster structure is examined by use of mass spectronomy. It is found that, among the stable liquid phase clusters, the (H2O)21H{sup +} cluster is the most stable. Stable hydrate clusters are in presence in quantities, and participate in the formation of hydrate crystal nuclei. For the elucidation of the nucleus formation mechanism, a kinetic simulation is conducted of molecules in the cohesion system consisting of water and methane molecules. Water molecules that array near methane molecules at the normal pressure is disarrayed under a higher pressure for rearray into a hydrate structure. Hydrate formation and breakdown in the three-phase equilibrium state of H2O, CH4, and CO2 at a low temperature and high pressure are tested, which discloses that supercooling is required for formation, that it is possible to extract CH4 first for replacement by guest molecule CO2 since CO2 is stabler than CH4 at a lower pressure or higher temperature, and that formation is easier to take place when the grain diameter is larger at the formation point since larger grain diameters result in a higher formation temperature. 3 figs.

  13. Investigation on vibrational dampers for cables of Tsurumi Tsubasa bridge; Tsurumi tsubasabashi no keburu seishin hoshiki ni kansuru jisho

    Energy Technology Data Exchange (ETDEWEB)

    Takano, H.; Ogasawara, M.; Shimosato, T. [Metropolitan Public Corp., Tokyo (Japan); Yamada, H. [Yokohama National Univ. (Japan)] Murakami, T. [NKK Corp., Tokyo (Japan). Applied Technology Research Center

    1998-03-20

    In a long cable-stayed bridge, countermeasure against wind induced vibration should be often taken at the same time together with the measure against angular bent phenomena (phenomena in which secondary bending stress is generated on the front of fixing socket by live load). The conventional countermeasure is a combined use of buffer rubber and dampers. This study points out problems in the conventional countermeasure on the application to the cables of the Tsurumi Tsubasa Bridge and combination of dampers and angular bending buffer device is examined. The result shows that a combined use of high-damping rubber and oil dampers enables installation of the dampers in a lower position while maintaining the performance and is excellent in the easiness in installation and maintenance and in aesthetic view. This system was applied to the Tsurumi Tsubasa Bridge and the effectiveness on damping and angular bending relaxation was confirmed through the model tests, and vibration tests and field observation on the cables. 9 refs., 20 figs., 7 tabs.

  14. Static behaviors of long-span cable-stayed bridge; Chodai shachokyo no seiteki kyodo ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Xu [Saitama Univ., Saitama (Japan). Graduate School; Yamaguchi, H.; Ito, M. [Saitama Univ., Urawa (Japan). Faculty of Engineering

    1996-04-21

    In this study, incremental equation of cable-stayed bridge is formulated by finite element method taking the geometrical nonlinear analysis into account. Then, as an example of designing a bridge with 1500m span, setting up the initial tension, analysis of in-plane behavior caused by live loads as well as analysis of the behavior against wind caused by out-of-plane wind load that are necessary for designing a bridge with 1500m span are carried out. The main results obtained through the study are as follows. As for the cable stayed bridge with 1500m center super long-span having supplementary supporting points between the side arms, the geometrical non-linearity caused by the in-plane design live loads is not remarkable. The effects of wind which acts on girders on analysis of the behaviors against wind are different depending on the aerodynamic performance of the girder and in the case of high wind speed, strong effects on the behavior against wind of the in-plane and screws generate. As the changing of tension of the cable makes influences on the force of in-plane cross section and on displacement of the girder, if the wind speed is very high, the analysis results of the behaviors against wind of in-plane and screws of the cable-stayed bridge may be different depending on in what manner the wind load on the cable to be treated. 16 refs., 16 figs., 1 tab.

  15. Study on the structural characteristics of extradosed concrete bridges; Ekusutoradozudo kyo no kozo tokusei ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Oka, Y. [Japan Highway Public Corp., Tokyo (Japan); Kasuga, A. [Sumitomo Construction Co. Ltd., Tokyo (Japan); Yamazaki, J. [Nihon Univ., Tokyo (Japan). Coll. of Science and Engineering

    1997-03-31

    Parameters are analyzed to provide data for deciding, in the planning and designing stages, whether a cable stayed bridge or an extradosed bridge should be adopted. Comparative investigation of the vibration properties of both types of bridges is also referred to. The result of the study on the structural properties of the cable stayed road bridge and the extradosed road bridge is introduced. Based on the concept of the extradosed bridge, designers are now able to select without restraint the after load sharing rate of the diagonal members. Parameter analysis of a diagonal member reinforced 3-span continuous beam is performed. By introducing indices showing the load sharing rate of the diagonal member, the cable stayed bridge can be distinguished logically from the extradosed bridge in designing. It is found important that the height of the main tower is set to approximately 10% the length of the center span for the construction of the extradosed bridge. The vibration properties of the cable stayed bridge and the extradosed bridge of the same scale are compared. 7 refs., 18 figs., 6 tabs.

  16. On the relationship between stacking process and resolution. 2; Jugo shori to bunkaino ni kansuru kiso kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J.; Rokugawa, S.; Kato, Y. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T.; Miyazaki, M. [Geological Survey of Japan, Tsukuba (Japan)

    1997-05-27

    With respect to concept of resolution in seismic exploration using the reflection method, detailed considerations were given on processes of forming the resolution as a result of arranging observation points at vibration transmitting and receiving points. In the discussion, numerical experiments were carried out, in which the scattering stacking process is applied in a model having one scatterer existing in homogeneous media. The experiments investigated an imaging formation process of the scatterer when arrangement of the vibration transmitting and receiving points were changed from a coarse condition to a dense condition while the number of transmitting and receiving points is being increased. Resolution is created if waveforms having finite frequencies are used as input, and the imaging is performed by utilizing the limited number of vibration receiving and transmitting points. If the concept of equi-travel plane is used under these conditions, the equi-travel planes perform negation with each other, and it was indicated that visual resolution is expressed by how good the negating effect is. It was discovered that such concept of the resolution is quite ambiguous in terms of engineerings. 2 refs., 17 figs.

  17. Development of coal gas production technology acceptable for fuel cells; Nenryo denchiyo sekitan gas seizo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Kimura, N.; Omata, K. [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    In utilizing coal for high-efficiency direct power generation using fuel cells, it is necessary that coal be fed into the fuel cells after having been made into ash-free gaseous fuel. Research and development works are being carried out with an objective to develop a coal gasification furnace most suitable for fuel cells and establish a system to refine coal up to the one that can be fed into fuel cells. Fiscal 1995 has conducted investigations on coal gasification technologies, air separation technologies, and gas refining technologies as the important element technologies, and a trial design on integrated coal gasification fuel cell (IGFC) systems. This paper reports from among the above items the result of the trial design on an IGFC system using molten carbonate fuel cells. The paper describes system comparison on paths of produced gases and anode waste gas, comparison on refining processes using a wet system and a dry system, and parameter studies on oxygen concentration in gasifying agents. It was made clear that the suitable furnace is an oxygen blown coal gasification furnace, and the power generation efficiency at the system terminal can be higher than 53%. 11 figs., 6 tabs.

  18. Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

  19. Study on torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, N.; Kishimura, K. [Meiji University, Tokyo (Japan)

    1996-10-27

    Discussing the rotor blades of the torsion arc blade type (TABT) wind turbine, difference in windmilling characteristics was determined between elliptic blades and rectangular blades by theoretical analysis and model experiment. Experimental generation of power was carried out using a test wind turbine in the natural wind. First, elliptic blades were bent into arcs and fixed to shaft. The action force was determined calculating the blade area and the wind velocity vertical thereto. Furthermore, the force in the direction to turn the rotor was determined with the effect of the part behind the blade taken into account. The rotation-curbing air resistance in the flank direction that a rotor experiences was subtracted to determine the torque generated. A formula was derived for the elliptic blade. Second, a formula was derived in the same way for the case of rectangular blades. In conclusion, in the case of 6-blade wind turbine, the rate of responsibility for wind turbine rotation of the part behind the blade was approximately 50% of the part in front of the blade. Shape coefficients were introduced into the theory, which resulted in values agreeing well with values obtained from experiments. Elliptic blades yielded more power than rectangular blades at the same wind velocity. High in durability, the TABT wind turbine is expected to be put into practical use as a compact auxiliary power generating device. 2 refs., 14 figs.

  20. Fundamental characteristics on electric system of solar electric vehicle; Solar car no denki keito ni kansuru kiso tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, S.; Sasaki, M.; Kaga, T.; Koyama, N. [Hachinohe Institute of Technology, Aomori (Japan)

    1996-10-27

    The electric system of a solar vehicle was removed and the fundamental characteristics examined in order to carry out a basic experiment on the electric system. Using a basic circuit with panels, batteries and loads connected, the voltage and current were measured in the presence/absence of the trackers, batteries, etc., and then, their effects were examined. Simultaneously, the quantity of solar radiation was also measured. The lowering of the output voltage was somewhat relaxed with the use of the trackers. Further, with the trackers used, the output voltage of the panel was small in spite of a large quantity of solar radiation compared to the case without the trackers, which was due to the restriction of the output voltage by the trackers. When measured without batteries, the output voltage of the panel was such that the load current was also influenced by the variation of insolation, so that, with a large decrease in insolation, the load current was decreased with the supply of current suspended from the panel. 7 figs., 1 tab.

  1. Performance analysis on natural energy autonomous house (HARBEMAN house); Shizen energy jiritsu house (HARBEMAN house) ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujino, T.; Saito, T. [Tohoku University, Sendai (Japan)

    1996-10-27

    To reduce fossil fuel consumption and CO2 emission, this article introduces an actually constructed natural energy autonomous house. It has a solar collector on the south roof for hot water supply and a sky radiator on the north roof for cooling water supply. The sky radiator uses radiation cooling phenomena into the space by electromagnetic wave through the window of atmosphere. This house also has an insulated tank with a capacity of 31 m{sup 3} in its underground. In the long-term heat storage mode, the heat is collected through the solar radiation during the period from summer to spring and is stored in the underground water tank, to use it for heating and hot water supply in winter. The heat can be recovered from the garbage waste incinerator. A gas fired auxiliary boiler is used for the shortage. In the long-term heat regeneration mode, the heat is regenerated through the sky radiator during the period from spring to summer and is stored in the underground water tank, to use it for cooling in summer. For the shortage, the water is cooled using a heat pump operated by the midnight power. The insulating performance is improved by using the pair glass in windows and the glass wool in the walls. Rain water is collected in a tank with a capacity of 2 m{sup 3}, to use it for toilet water. Annual energy and water saving is equivalent to 600,000 yen. 10 refs., 10 figs., 2 tabs.

  2. Demonstrative study for the wind and solar hybrid power system. 2; Furyoku taiyoko hybrid hatsuden system ni kansuru jissho kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kimura, Y.; Sakuma, H.; Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan)

    1996-10-27

    In order to verify the complementary relationship between wind and solar energy, the long-term field test of the hybrid power system was conducted at the natural energy square of Ashikaga Institute of Technology. The solar cell blade windmill composed of a Savonius windmill and flexible solar cells applied to swept buckets was also prepared. As a result, the wind power generation was promising mainly in the winter period including the late fall and early spring, while solar one was stable all the year through although it was slightly poor in winter. Stable power generation was thus achieved by combining wind energy with solar energy. As the whole data of other wind and solar power generation systems at the square were analyzed for every month, the same conclusion as the solar cell blade windmill was obtained as follows: the wind power generation in Ashikaga area is promising in Nov.-March from the field test result for 16 months, solar power generation is stable all the year through, the hybrid power system is effective in Nov.-April, and the solar cell blade windmill is equivalent to the hybrid power system. 3 refs., 5 figs.

  3. Study on the self-compacting property of high fluidity concrete; Koryudo concrete no jiko jutensei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, H.; Dozono, A.; Obatake, A. [Nihon Cement Co. Ltd., Tokyo (Japan); Nagataki, S. [Niigata University, Niigata (Japan). Faculty of Engineering

    1997-08-20

    Mechanized work of high fluidity concrete is possible because of its self-compactability (SC), however, it requires both high fluidity and non-separability of materials as basic conditions, and yield strengths over a certain value. Unlike Newtonian fluid, the SC is thus restrained. For improving the reliability of the SC of high fluidity concrete, the predicting method of the SC was proposed on the basis of a self-compacting mechanism model. It was assumed that the SC is dependent on a surface resistance of formworks, internal friction angle of concrete, and resistance due to steel bars. The estimation equation of the frictional resistance of formworks was derived from formwork material properties and coarse aggregate bulk concentrations. The equation of the internal friction angle of high fluidity concrete was also derived from coarse aggregate bulk concentrations. The validity of this model was confirmed by verifying the SC with a model formwork and real structures. Prediction of the SC by this method before placing can improve work reliability. 4 refs., 24 figs., 15 tabs.

  4. Investigation on development of advanced materials by solvothermal technique; Sorubo thermal hanno riyo senshin zairyo kaihatsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Solvothermal reaction is reaction under high temperature and high pressure, which is expected to fabricate new functional materials. In this study, the materials are classified into two fields, i.e., inorganic materials, metals and their composites and organic materials and their composites. The current status of R and D of production and processing technology in each field is surveyed and the prospect of it is discussed. For the inorganic materials, metals and their composites, it is explained that very fine metal oxide particles, complex oxides, single crystals, whiskers, compounds with layer structure, metastable compounds, ion conductors and catalysts with high ability could be produced only by controlling the solvothermal reactions in atomic order. For the organic materials and their composites, surveyed results of the solvothermal technique using non-aqueous solutions are mainly provided. The necessity of a national project for researches on the solvothermal reactions is proposed from the viewpoint of resource, environment and energy. 777 refs., 38 figs., 26 tabs.

  5. Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

  6. Indoor environment and allergy except housedust mite; Jukankyo to allergy ni kansuru dani igai no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakao, F.; Nishima, S.

    1998-05-31

    Pathopoiesis factors of allergic diseases include immune antibody productivity sthenia reacting with antigens such as mite or the like in allergy reaction which is regarded as based on genetic fact (atopic diathesis), and environmental factors as external factors. The environmental factors are further classified into specific factors (antigens) and nonspecific factors. The former factors include the indoor factors such as mite, mould, animals bred indoor, etc., and outdoor factors such as pollen and so on. The latter factors include indoor factors such as passive smoking, carbon monoxide, nitrogen oxides, formaldehyde, etc., and outdoor factors such as sulfur oxides, nitrogen oxides, airborne particles and so on. In this paper, the environmental factors in relation to allergic diseases expect mite are introduced. Besides mould, cockroach/insect, fur dust and dandruff of animals, adjustment of room temperature/humidity, smoking, indoor and outdoor air pollution are mentioned as the environmental factors expect mite, and the cause-effect relations thereof are explained. 24 refs., 3 figs., 7 tabs.

  7. Fiscal 1995 investigation on biological fixation of carbon dioxide; 1995 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To cope with the global warming caused by CO2, an investigation was conducted into biological fixation. It is necessary to make a many-sided and comprehensive study on the mechanism of CO2 fixation, the scale (area and carbon holding density), the rate and the environmental impact of the introduction of the technology and the technical problems, and to make a quantitative evaluation of each of the methods in order to make them practical proposals. The global ecosystem is classified into the land biota and ocean biota, and each typical ecosystem was surveyed in terms of the surface area, the carbon holding amount (presently existing amount), the net primary production amount, the required nutrient salt amount, the transpiration rate, etc. Next, a discussion was made on the increasing effect of the carbon fixation amount by changing the present ecosystem from the aspect of scale and rate. At the same time, a study was carried out of energy efficiency, economical efficiency and problems. Last, elementary technology was taken up which seems to be important for implementing measures for the biological carbon fixation. As to the ocean, it is necessary to obtain information, which is not sufficient to utilize marine biota for CO2 fixation, especially on the mechanism of depth-direction transfer of organism and its quantitative grasp. As to the land, one of the measures is conversion of the ecosystem where the amount of carbon fixed is small to the ecosystem where the amount is large. 249 refs., 58 figs., 51 tabs.

  8. Survey on bio-chemical complex harmonized with global environment. 3; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    A survey was conducted of bio-chemical complex harmonized with the global environment for the purpose of constructing the material production process harmonized with the environment by the process fusion between biological conversion and chemical reaction. Palm oil was taken up as renewable raw material plant resource. The process utilizing bio-chemical reaction advances at normal temperature and pressure and is high in reaction specificity and selectivity. This is a recycling, circulation and environmental harmony type production technology which brings high yield, energy conservation, resource conservation, and low environmental loads. Waste water treatment and production of useful substances from sludge were thought as elementary technology. A possibility was studied of enzyme production by culturing solid waste, and the enzyme was applied to the hydrolysis process. The paper indicated trace components in the palm oil and the extraction method and proposed the production process of new derivatives for adding value to hydrolysate. A study was also made of the overall process flow which integrated these new processes and the material balance. The comprehensive evaluation of this new process was made from the aspect of the product structure, the market, construction cost, economical efficiency, and the environment. 133 refs., 65 figs., 56 tabs.

  9. Research and development of jellyfish compaction technology; Kurage gen'yoka shori gijutsu ni kansuru kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Uemura, N. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1999-12-10

    An on-site test is conducted of devices for reducing in a short time the volume of jellyfish that flow into power plants. There are three methods to reduce the volume of jellyfish by separating water from them, which are heating, pressing, and chemical. The chemical treatment is not an object of this test because it is expected that the volume reduction rate by this method will be too low. For the achievement of a reduction rate of 80%, the two methods, physical and crushing, are compared at the laboratory level. It is found that the crushing method is superior because it can dispose of jellyfish in a shorter time. Using this method, the crushed jellyfish is separated into drain and bubbles, the latter containing jellyfish fragments. An on-site test is conducted using a general-purpose crusher. The relationship between the filter diameter (1-5mm) and the separation rate is investigated, and it is found that separation proceeds more rapidly when the filter diameter is smaller. It is found that the addition of a certain chemical accelerates the separation. COD (chemical oxygen demand) is 300-490mg/l in the drain, and BOD (biological oxygen demand) 400-500mg/l, with COD having increased by approximately 20%. A study is scheduled to be conducted using an experimental apparatus. (NEDO)

  10. Study on seepage water circulation in landfill waste disposal site. Haikibutsu umetate shobunchi shinshutsusui no kankyo ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Hosomi, M.; Nakasugi, O. (National Institute for Environmental Studies, Tsukuba (Japan))

    1990-10-29

    The report presents a study on the treatment of seepage water discharged from the waste layer in a landfill waste disposal site and on seepage water circulation as a method for accelerating the stabilization of waste in a landfill site. Seepage water circulation is intended to feed seepage water back onto or into the waste layer so that water is distibuted uniformly over the waste layer. Study results show that seepage water circulation can effectively remove those organic substances which are associated with BOD and COD. In Japan, seepage water circulation is mainly performed by spreading water over the landfill site with the aim of reducing the amount of seepage water through evaporation. Circulation also serves to accelerate the generation of gas such as methane and carbon dioxide. Circulation causes a depression, which acts as a total index reflecting not only biological and chemical reactions but also physical processes. It is also found that the acidic fermentation which occurs during the landfill stabilization process can be promoted by properly controlling the pH value. 2 tabs.

  11. Fiscal 2000 study on technology and marketability concerning phytoremediation; 2000 nendo phytoremediation ni kansuru gijutsu oyobi shijosei no chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigative study was conducted on phytoremediation with the purpose of correcting soil contamination caused by heavy metals and the like. In Japan, in connection with the cadmium pollution along the Jintsugawa River region in Toyama Prefecture, a growth of botanical colony such as Athyrium ykoscense was confirmed having a high capacity in absorbing/accumulating heavy metals, with a possibility suggested that they may be utilized for phytoremediation. In a technological research for restoring the environment sustainingly in a wide area, feasibility has been proven to remove polluting agricultural chemicals in farmlands and toxic substance in old industrial sites by making forest trees like poplars, lawns and herbage function. In a project for the cleanup of oil contaminated soil after Gulf War, a demonstrative test of bioremediation for one hectare was performed and, after 15 month experiment, 80 to 90% of aliphatic compounds and 50 to 60% aromatic compounds were degraded. In EU Framework Program in Europe, phytoremediation projects have been implemented across the member countries. (NEDO)

  12. Numerical simulation on streaming potentials in a wellbore; Koseinai no ryudo den`i ni kansuru suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, N. [Kyushu University, Fukuoka (Japan)

    1996-05-01

    This paper reports numerical computation of streaming potentials which are generated by transient pressure waves propagating the vicinity of wellbore wall immediately after a mud cake formed on the wellbore wall has been removed. One existing analysis solution on heat conduction was utilized upon changing the parameters in order to derive fluid pressure inside the ground bed. Calculations were carried out by using the existing three-dimensional finite difference method (partly re-written) based on the relationship constituted between the fluid pressure and the streaming potential. This paper presents results of calculating the streaming potentials in wellbores on models having wellbores filled with mud water in a cubic ground bed existing with ground bed water at saturation of 100%. The calculations have been conducted on the following cases: a case where permeability of the ground bed is small with the fluid under two conditions of low electric resistivity and high electric resistivity, a case where the permeability is large with the fluid under the above conditions, and a case where a small area of bore wall is covered with a rubber pad having high electric resistivity under a low electric resistivity condition. 8 refs., 5 figs.

  13. Report on Asian Environment Information Network; 'Asia kankyo joho network' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The goal is the construction of Asian Environment Information Network (AEInet) in accordance with a contract signed between Indonesia's LIPI (Indonesian Institute of Science) and NEDO under NEDO's Research Cooperation Project Concerning the Development of Environment Measuring Laser Radar (LR). The network is so designed and constituted as to operate on a private line between Indonesia and Japan via IP (Internet protocol) and to enable the exchange on the Internet network of the data collected/analyzed by the Indonesian LR system and of articles of e-mail between scientists of the two countries. The AEInet will be utilized for the collection/analysis of LR-collected data; exchange of observed data and the result of processing; provision of support to environment information scientists in exchanging e-mail and information; and the search of databases for the implementation of the project. In this paper, the outline and functions of the system, network system design, WWW server construction, network operating status, joint researches with Indonesia, etc., are described. (NEDO)

  14. Study on a method to set design hydrographic conditions; Sekkei kaisho no setteiho ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Toki, N. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1996-10-01

    Analyses were performed recently on results of observations having been carried out by the U.S. National Oceanic and Atmospheric Administration (NOAA) and the Japanese Meteorological Agency by using wave observation buoys. Wave observation database with high reliability has become publicized in the same format as the conventional wave generation frequency data. In order to obtain rational base for a method to set hazardous sea areas, the present study has attempted to express as a function of the average wave cycle a maximum value of significant wave heights which can be generated based on these data. What were derived include observations by the NOAA over large areas, such as Alaskan coasts, Mexico Bay and Five Great Lakes, the results of discussions by the Meteorological Agency on data including wave observations at five locations in neighboring waters in Japan, and the relationship between the maximum value of significant wave heights that can be generated and the average cycle. Deriving the standard deviation per unit wave height by computing short time estimation from the above data, and deriving combination of the average cycle with angles of encounter can present the design hydrographic conditions (hazardous hydrographic conditions). The future would require not only investigations and discussions from the viewpoint of the maximum value that can occur, but also from the viewpoint of determination of limitations of vessel operations. 5 refs., 5 figs.

  15. Consideration on fatigue strength of corroded steel plates; Fushoku suimo koban no hiro kyodo ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Iwata, M.; Yajima, H.; Yamamoto, M.; Saito, T. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-10-01

    Discussions were given on fatigue strength of corroded steel plates taken from a hull of a ship seventeen years old after construction. The steel plates have had their original thickness of 13 mm reduced to 5.3 to 8.3 mm. After having been cut by a machine, the steel plates were used for tests as ground plates after going through grinding and as corroded plates with rust remaining on them. The fatigue test was performed in artificially made sea water at a temperature of 25{degree}C and in air with axial power pulsating tensile load and at iterative loading velocities of 3 to 5 Hz. The corroded material test verified that corrosion pits exist innumerably on the test piece surface and fatigue cracks have been developed and grown from bottoms of the pits. The stress concentration coefficient of the corrosion pits was about 1.9. Good agreement with the test result was found in the S-N chart in which the number of iteration of fracture was regarded as the number of iteratively generated cracks, and notch coefficient was estimated as 1.9. These results proved that the fatigue strength assessing method for virgin materials can be applied also to steel plates which have been exposed to corrosive environment for extended periods of time. 5 refs., 7 figs., 1 tab.

  16. Experimental consideration on control of a ROV for lifting objects. Suichu sagyo sensuitei no seigyo ni kansuru jikkenteki kento

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Yoshida, K.; Nagai, H. (Univ of Tokyo, Tokyo (Japan). Faculty of Engineering); Tanaka, H. (Central Japan Railway Co., Nagoya (Japan))

    1991-12-01

    In the control of ROVs with a position sensor (by means of under sea accoustics) and computer aided trajectory controlling function, it is only necessary to provide an information on the orbit to follow. In order for reducing the burden for the operators it will be frequently used in the future under-sea operations. Especially, in addition to such conventional operations as inspection and examination, materials transportation will be an important role. In this study, in order to apply an orbit trajectory control using a sliding mode to ROVs, a basic system was constructed which contained an ultrasonic location detecting system. Confirmation of basic actions of the orbit trajectory control control to follow a three-dimensional orbit. Maximum error to the preset orbit was within 5 m. It was found that the ROVs could hoist an object of 530 g mass (60 g in water) corresponding to 10% of the weight of the vehicle and transferred in a changed dynamic conditions. 10 refs., 18 figs., 3 tabs.

  17. Study about the effect of microgravity on biofunctions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A study is made for the elucidation of the effect of microgravity on biofunctions. The protoplast of shiitake is exposed to microgravity and then cultured, and a significant difference occurs. The rate of colony formation by cell fusion in the test sector is found to be two times higher than that in the control sector. When swimming ciliates which are unicellular are suddenly exposed to microgravity, their swimming speeds changed differently according to the direction of swimming. When a mouse subjected to acupuncture for three days is exposed to microgravity, its water metabolism and excretory function are enhanced. A mouse treated with Chinese medicine reacts in the similar way. The change due to microgravity in the amount of acetylcholine in the hypothalamus is found characteristically time dependent. Mice infected with lethal herpes viruses just after exposure to microgravity die at a rate in proportion to the number of exposures and to the amount of viruses given. The migration speed of chemical stripes in case of a gel-base BZ (Belousov-Zhabotinsky) reaction under microgravity is equal to that on the ground. The trigger wave migration speed in case of a water solution-base BZ reaction under microgravity is reduced to approximately 80% of the speed on the ground. 12 refs., 31 figs., 3 tabs.

  18. Investigational study on construction of the physical function database; Shintai kino data base no kochiku ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was carried out on construction of the physical function database which can supply data useful for planning, design and production when companies provide products and barrier-free environment for the aged society. Up to now, the final image of database was studied as to the visual function. In addition, this study is aimed at constructing the physical function database. In the literature survey, basic data on physical characteristics of the aged which have lain scattered were collected and systematically sorted in relation to the exercise function in order to make an analysis of the data and measuring technology in terms of reliability, importance, and applied values. In the survey of corporate needs, an examination of concrete needs for the exercise function and auditory function was made for general companies and companies related to the medical and welfare apparatus field. As to the visual function, a study was conducted on selection of new items for visual measurement and measuring methods. In the study of the database structure, a pilot database was constructed and subjects were extracted. 529 refs., 57 figs., 15 tabs.

  19. Consideration on AC loss evaluation of oxide superconducting wires (1); Sankabutsu chodendo senzai no koryu sonshitsu hyokaho ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, H.; Terasawa, Y.; Kajikawa, K.; Iwakuma, M.; Funaki, K. [Kyushu Univ., Fukuoka (Japan)

    2000-05-29

    In the oxide superconducting wire rod, the gradient of the E-J characteristics compares it with metal system superconducting wire rod, and in the gentle sake, the evaluation of the ac loss using critical current may contain large error. And, it is also possible E-J characteristics n value model numerical calculation loss. It needs the considerable labor in this case for the calculation. It evaluated this junction current numerically under various conditions this time, and it tried the formulation of the junction current. And, it also did the prediction of the energization loss using got evaluation system. (NEDO)

  20. Studies on Stirling engine with pendulum-type displacer; Furikoshiki displacer puresa wo yusuru stirling engine ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Isshiki, N. [Nihon University, Fukushima (Japan). College of Engineering; Igawa, Y. [Shiroki Corp., Yokohama (Japan); Isshiki, S.

    1995-12-25

    This paper describes in detail the experimental and theoretical results of a new type of Stirling engine with a pendulum-type displacer (PDSE) that is suspended by a hinge shaft and swings in a displacer space. The main features of PDSE are its simplicity, ease of outside gas sealing, and lower mechanical friction than that of the conventional-type Stirling engine. However, gas leakage inside the displacer is larger than that of the conventional type. The power required to induce a pendulum-type displacer motion, which consists of flow loss powers of multiple fin gas passage and regenerator wire mesh, is analyzed using a simple equation. It has been clarified that the calculated theoretical power output agreed well with the experimental power output. It has also been clarified that the measured Nusselt number of the regenerator agreed with that of a previous study. It is hoped that PDSE can be employed to utilize natural heat energy sources in the future. 8 refs., 10 figs., 2 tabs.

  1. Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-10

    Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

  2. Survey on bio-chemical complex harmonized with global environment. 2; Kankyo chowagata seibutsu kagaku konbinato ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The technical background was investigated for the purpose of making an effective use of the environmentally harmonized type production process and biomass resource, and the concept was indicated of a biochemical complex using vegetable fat and oil as a raw material. The vegetable fat and oil used were mainly palm oil and coconut oil. As to the production of commodity chemicals from palm oil, investigations were made on the outlook of the production amount and the composition of fat and oil, and a study was made on a possibility of substituting palm oil for beef fallow as a raw material of fatty acid. Relating to a large amount of the waste of biomass left after collecting the useful part of plants with fat and oil, a process was studied and proposed of producing useful enzymes by the solid culture method in which the biomass waste was used as a raw material. The enzymes produced here were made to be used for conversion of fat and oil and production of bioplastics, etc. Also, as to the plastics produced by microorganism, results of the recent research were examined on fungus bodies and the culture medium, bioreactors, separation and refining after producing fungus bodies, physical properties of the plastics, etc. 178 refs., 77 figs., 68 tabs.

  3. Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-04-20

    Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

  4. Basic study on CO2 solidification by haptophycean algae (phytoplankton). Haputoso no tansan gas kotei ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, M. (The Kasai Electric Power Co. Inc., Osaka (Japan))

    1994-06-25

    A basic study was made on CO2 solidification by haptophycean algae as phytoplankton. Haptophycean algae have functions of not only carbon dioxide assimilation but also of CO2 calcification. By using Gephyrocapsa oceanica and Pleurochrysis haptonemofera as haptophycean algae, optosynthesis velocity and calcification velocity were measured by a carbon isotope method, the CO2 solidification capacity of both algae was compared, CO2 partial pressure changes in the culture process and changes in the amount of inorganic and organic carbon by alga culture in high concentration CO2 were measured. As a result, it was revealed that carbon solidification increased in alga culture in high CO2 concentration. It was also revealed that acceleration of calcification velocity required high photosynthesis velocity. There is a possibility that CO2 may be solidified by culturing haptophycean algae. The solidification ability of Pleurochrysis haptonemofera is about the same as that of chlorella algae. It was calculated that an area of 2.8 [times] 10[sup 4] ha. was required for 7.4 [times] 10[sup 9] kg CO2 emitted from a power plant. 16 figs., 1 tab.

  5. International Workshop on Carbon Cycling and Coral Reef Metabolism; Sangosho no tanso junkan ni kansuru kokusai workshop hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-16

    The paper described the International Workshop on Carbon Cycling and Coral Reef Metabolism which was held at Miyako-jima, Okinawa Pref. on October 17-24, 1995. In the workshop, researchers got together which are involved in marine chemistry, marine biology, coral ecology, and environmental science, and discussed the carbon cycling and metabolism of coral reef. Discussions were made on what the coral reef ecosystem is, and what the definition of a sink or a source for CO2 is. Also discussed were scales of how much time and space should be considered to make these issues clear. Further, it was proposed that it was necessary to investigate carbon balance of both the whole system and the components of the system and to keep track of mass transfer among neighboring components of the system. Seventeen presentations were given. The workshop obtained a definite consensus on carbon balance of the coral reef system. 123 refs., 39 figs., 9 tabs.

  6. Research on application of heat pump on cyclamen culture. Shikuramen saibai eno heat pump tekiyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nada, Hidetoshi (Kyushu Electric Power Co., Inc., Fukuoka (Japan))

    1989-03-30

    The culture test by introduction of heat pump was conducted for the culture process of cyclamen. As the result of the test, cultivating technology which was capable to deliver cyclamen twice a year, in September and December, together with the reliable technology to cultivate it in large pots (No 7, 8 flower pots) to deliver it at the end of year, were established. Disease and outbreak of injurious insects such as wilt and grey mold were capable to be almost prevented by air-conditioning and dehumidifying system, therefore superior quality cyclamen with beautiful flowers was grown. Further, under-bench culture test which has never been examined, was applied to Daimonji-so, then much interest supplemented by its running cost, was attained. Beside the above, the profitability of heat pump was verified, and energy conservation and labor saving were realized by the automation on opening and closing of green house windows and curtains, on starting and stopping of heat pump which was operated in compliance with set temperature, humidity and quantuty of solar radiation. 7 figs., 10 tabs.

  7. FY1995 basic research for neuroactive materials; 1995 nendo shinkei kino zairyo kaihatsu ni kansuru kiban kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Development of nenroactive materials to improve neuronal defects is one of the most important subjects in Japan that will soon become a aging society. In this project, basic research for neuroactive molecule was performed to develop technology for neuronal regeneration, regulation of synaptic activity and interface between artificial surface and living neurons. A novel neurite promoting factor was discovered and its cDNA was cloned. Mutagenesis in vitro showed that a functional region of this factor located in a polypeptide of less than 50 aminoacids. Using neuronal culture, synapse formation was found to depend on two modes of activities and long-lasting synaptic potentiation was demonstrated to depend on a macromolecules released from pre- or postsynaptic neurons. To regulate nervous activities, photoactivated caged-peptide was developed and confirmed to change in affinity to its receptor. Neurons were cultured on substrates paterned by microlithography. (NEDO)

  8. Outline and summary of research for a database of unused energy technologies; Miriyo energy ni kansuru data shu sakusei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For effective promotion of the new energy utilization project of NEDO and preparation of the future new energy vision, the data on unused energy were systematically arranged. The definition of heat supply systems using unused energy was clarified, and the kind and property of unused energy were arranged. Some typical systems of heat supply facilities using unused energy were presented. The data were classified by energy source, temperature level and region, and the detailed database was prepared for the typical systems. The overseas database was prepared, in particular, for European and American systems. Domestic and overseas policies, laws and subsidy systems were arranged. The introduction effect of two heat supply facilities using unused energy was surveyed, and their operation costs were analyzed. Basic terminology related to unused energy was compiled and explained. Related organizations, in particular, manufacturers were surveyed and arranged. The main manufacturers of a heat recovery refrigerator and waste heat boiler as typical equipment, and the number of these equipment shipped were arranged. 51 figs., 116 tabs.

  9. Filtration coefficients and physical properties of fluids for osmotic action; Shinto gensho ni kansuru roka keisu oyobi busseichi

    Energy Technology Data Exchange (ETDEWEB)

    Ipposhi, S.; Imura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Konya, K. [Oji Paper Co. Ltd., Tokyo (Japan); Aoyama, N. [Kumamoto University, Kumamoto (Japan)

    1998-04-25

    In this study, filtration coefficients of tubular type osmosis membranes made of acetyl cellulose are measured by two methods. Effects of temperature and concentration on physical properties of fluids needed for study on osmotic action are also investigated using sodium chloride, potassium chloride, sucrose and polyethylene glycol 600 aqueous solutions as the testing fluids. As a result, a new method for measuring the filtration coefficient is proposed by making use of osmosis and it is clarified that there is no difference between filtration coefficients for osmosis and reverse osmosis processes. In addition, equations for mass diffusivity, permeability, viscosity and density of the above fluids are presented. 11 refs., 21 figs., 2 tabs.

  10. Study on the effect of measurement points upon reduced added mass matrix; Shukusho fuka shitsuryo matrix ni okeru kansokuten no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

    1996-12-31

    It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. A parameter calculation was performed on node vibration in the vertical direction of a rotating elliptic body such as a ship to investigate the effect of an arranging method of the measurement points upon the result of the analysis. As a result, it is thought that equivalent interval arrangement of 21 measurement points would be sufficient in a lower order side mode of vibrations with less than four nodes. An analysis of calculations performed by arranging measurement points in experimental measurement points revealed that analysis accuracy would not increase even if the number of measurement points is increased if it is done so without considering rotation vector. An experiment was carried out with the number of measurement points increased to verify the above fact, with which the analysis was verified correct. Therefore, as has been forecasted in the previous report, the cause for the analysis accuracy deterioration in a high order mode may be estimated as the effect of the rotation vector. However, since it is not the situation that an analysis considering the rotation vector has been conducted, it cannot be concluded yet that the effect of the rotation vector is the sole cause. 4 refs., 14 figs., 7 tabs.

  11. Studies on carbon dioxide emission control. With an emphasis placed on Korean industrial structure; Nisanka tanso haishutsu kisoku ni kansuru kenkyu. Kankoku no sangyo kozo wo chushin ni

    Energy Technology Data Exchange (ETDEWEB)

    Ishitani, H.; Matsuhashi, T. [The University of Tokyo, Tokyo (Japan); Moriguchi, Y.; Kondo, Y.; Shimizu, H. [National Inst. for Environmental Studies, Tsukuba (Japan)

    1996-02-01

    An examination was made on the structures of CO2 emission in the Korean manufacturing sector for the purpose of drafting measures for regulating and controlling CO2 emission. With the use of a list of interactive industries, the emission was determined on the assumption that CO2 was discharged by the consumption of fossil fuel. 1985 and 1990 were chosen as the years to be examined. The industries with a large quantity of emission were construction, transportation, storage, communication and metal products/machinery. The largest factor that influenced the increase in the emission was the growth of the ultimate domestic demand, and the next factor was export. On the other hand, a factor worked in the direction of reducing the emission was the change in the emission coefficient and technical changes. It would be important that measures for CO2 emission control be centered for a short term on regulating the industry that has a high induced coefficient (using products from other industries having a high CO2 emission coefficient as intermediate products), and for a long term on regulating the ultimate domestic demand and export. The changes in the emission coefficient and the changes in technology would also be important in reducing the emission as well as the reform of the industrial structure. 2 refs., 3 figs., 2 tabs.

  12. Basic studies on application of vegetable factory in Tohoku region; Tohoku chiho ni okeru yasai kojo no jitsuyoka ni kansuru kiso kento

    Energy Technology Data Exchange (ETDEWEB)

    Okano, T.; Terazoe, H.; Shoji, K.; Nakaya, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan); Tanaka, M.; Miura, K. [Tohoku Electric Power Co. Inc., Sendai (Japan)

    1995-08-01

    To construct vegetable factories in the Touhoku region, items of information have been collected with respect to items to be cultured and market conditions. Experimental discussions have also been given on new culture items and methods for utilizing snow. Using the results of investigations on the market conditions and weather environments, the following three kinds of spicy vegetables were selected: water cress which grows in about 46 culture days after seeding and in about 36 days by herbaceous cutting to a harvest of about 700 g/m{sup 2}, green perilla which grows in about 85 culture days to a number of salable leaves of 100 per stock, with an average leaf area of about 55 cm{sup 2}, and trefoil which grows in about 56 culture days to a harvest of about 5100 g/m{sup 2}. According to a storage experiment using snow, lettuce packed with snow in a box retained at a temperature of 5{degree}C and a humidity of 100%, pre-cooled for one day and then stored for six days in a refrigerator at 5{degree}C presented very little decrease in fresh weight and no decrease in freshness. The same result was obtained also for the Sunny Lettuce. 9 refs., 19 figs., 9 tabs.

  13. Fundamental study on leak detection of underground gas pipeline using passive acoustic method; Judogata onkyo keisoku ni yoru maisetsu gas dokan hason kasho no kenshutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Jinguji, M.; Imaizumi, H.; Kunimatsu, S.; Isei, T. [National Institute for Resources and Environment, Tsukuba (Japan)

    1997-05-27

    With an objective to detect gas leaking from an underground gas pipeline, discussions have been given on a method which utilizes acoustic characteristics of leakage. On leaking sound generated from damaged portions, the form of damaging was hypothesized as pinholes, and spectra of leaking sounds from holes with different diameters were measured. The dominant frequency decreases as the hole diameter increases, while it is in a region of relatively high frequency of 1 kHz or higher. However, detection from the ground surface was impossible when cover soil has thickness from 0.5 to 1.5 m. In an experiment to measure leaking sound inside the pipe, pressure in the pipe was adjusted to 0.02 atm which is a standard pressure for a low-pressure pipe, and the sound was measured when the hole diameters were varied. In any of the results obtained by varying the hole diameter, spectra having the dominant frequency in the region of 1 kHz or higher were measured. In addition, it was found that sound pressure difference of as much as 50 dB at maximum is generated as compared with a case of no sound leakage. The above results verified that monitoring the high frequency of 1 kHz or higher is effective in detecting leakage from small damages. 2 refs., 4 figs.

  14. Study on estimating fluid force acting on a hull during maneuvering movement; Soju undoji no sentai ni sayosuru ryutairyoku no suitei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yukawa, K.; Kijima, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    With types of general cargo vessel and VLCC vessel as the object of discussion, a method was discussed to estimate fluid force acting theoretically on a hull during maneuvering movement, taking frame line shape into consideration. A vortex model was improved by giving consideration of time-based decay on intensity of discrete vortex lines based on the Rankine vortex. Modeling of flow fields around a hull was attempted to deal with movements in which width and draft are small as compared with the ship length, and turning angle speed and deviation angle are small. It was assumed that the ship speed is slow and effects of waves can be disregarded. Specular images of the hull were taken with regard to free surface, and handled as a double body model. Speed potential to express flow fields around a hull is required to satisfy the following five boundary conditions of Laplace, substance surface, free vortex layers, infinity and exfoliation. The potential may be handled as a two-dimensional problem in a field near the hull by using assumption of a slender and long body and conformal mapping. It was found possible to estimate hull fluid force with relatively good accuracy. Fine linear coefficients derived from the estimation were used to have performed highly accurate determination on course stabilization. 5 refs., 6 figs., 2 tabs.

  15. Investigations on an environment friendly chemical reaction process (eco-chemistry). 2; Kankyo ni yasashii kagaku hanno process (eko chemistry) ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In order to structure a chemical reaction process that does not discharge a large amount of waste by-products or harmful chemical substances, or so-called environment friendly process, investigations and discussions were given based on the results derived in the previous fiscal year. A proposal was made to reduce environmental load on development of oxidized and dehydrogenated catalysts that can produce selectively ethylene, propylene and isobutylene in an oxidation process. In liquid phase oxidation, redox-based oxidation and solid catalyzation of automatic oxidation reaction were enumerated. In acid base catalyst reaction, development of ultra strong solid acid was described to structure no pollution discharging process. In the fine chemical and pharmaceutical fields, the optical active substance method and the position-selective aromatics displacement reaction were evaluated to reduce environmental load. A questionnaire survey performed on major chemical corporations inside and outside the country revealed the following processes as the ones that can cause hidden environmental problems: processes discharging large amount of wastes, processes treating dangerous materials, and processes consuming large amount of energy. Development of catalysts is important that can realize high yield, high selectivity and reactions under mild conditions as a future environment harmonizing chemical process. 117 refs., 23 figs., 22 tabs.

  16. Studies on surface tension effect for free surface flow around floating models; Futai mokei mawari no jiyu hyomenryu ni oyobosu hyomen choryoku no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K. [Yokohama National Univ., Yokohama (Japan). Faculty of Engineering; Akiba, H. [Toyo Construction Co. Ltd., Tokyo (Japan)

    1996-12-31

    The effect of surface tension on free surface flow around floating models is discussed experimentally and numerically. Three-dimensional free surface flow around vertical circular cylinders floating in a circulating water channel was visually observed, where a surface-active agent was added to water. The results are analyzed using Weber number. The numerical analysis was done for vertical cylinder and CY100 models using the Rankine source method. Weber number of at least around 120 is necessary to eliminate the effect of surface tension from free surface flow around the CY100 model. The numerical analysis for the cylinder model needs simulation with wavelength shorter than that of free surface wave used by the Rankine source method. The model for the resistance test should be at least around 7m long to eliminate the effect of surface tension at Froude number of 0.1 or higher. 15 refs., 12 figs., 2 tabs.

  17. Topographical effects on wave exciting forces on huge floating structure. 2; Ogata futaishiki kaiyo kozobutsu ni sayosuru haryoku ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Imai, Y. [Hiroshima University, Hiroshima (Japan); Okusu, M. [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1996-12-31

    A method to predict drift force acting on a floating structure has been developed for a marine structure consisting of a number of floating elements, positioned in a region having a slope at the sea bottom. When a huge marine structure, such as floating air port, is located in a coastal area, scale of the overall structure is very large, of the order of scale of water depth change. The new method assumes that a marine structure consisting of an infinite number of cylindrical floating elements is installed in parallel to the seashore, where symmetrical nature of the configuration allows to predict behavior of the whole system by analyzing one element. Integration of pressures acting on structure surfaces determines the horizontal component of the drift force acting on the structure. Being influenced by topography, drift force predicted peaks at a frequency different from that for the level predicted on the assumption of constant water depth. This indicates the necessity for consideration of seabottom slope and effects of broken waves at the seashore. 6 refs., 12 figs.

  18. On the estimation method of hydrodynamic forces acting on a huge floating structure; Choogata futai ni hataraku haryoku ryutairyoku no suiteiho ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kagemoto, H.; Fujino, M.; Zhu, T. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    A floating structure such as an international airport is anticipated to have a length of about 5,000 m and a width of about 1,000 m. A singular point method may be used as a method to estimate force that such a floating body is subjected to from waves. In order to derive a solution with practically sufficient accuracy, 1250 elements are required in the length direction and 250 elements in the width direction, or a total of 312,500 elements. Calculating this number of elements should use finally a linear equation system handling complex coefficients comprising 312,500 elements, which would require a huge amount of calculation time. This paper proposes a method to derive solution on wave forces acting on a super-large floating structure or fluid force coefficients such as added mass coefficients and decay coefficients at a practically workable calculation amount and still without degrading the accuracy. The structure was assumed to be a box-shaped structure. Strengths of the singular points to be distributed on each element were assumed to be almost constant except for edges in lateral, oblique and longitudinal waves. Under this assumption, the interior of the floating structure excepting its edges was represented by several large elements to have reduced the number of elements. A calculation method proposed based on this conception was verified of its effectiveness. 2 refs., 25 figs., 3 tabs.

  19. Questionnaire investigation for the earthquake in Honjo city and Yazawa city, Akita Prefecture; Jishin ni kansuru ishiki chosa (Akitaken Honjoshi oyobi Yuzawashi ni okeru anketo kara)

    Energy Technology Data Exchange (ETDEWEB)

    Nogoshi, M. [Akita University, Akita (Japan). College of Education; Kabutoya, S.

    1996-05-01

    Consciousness for the earthquake was investigated by questionnaire surveys made in Honjo City and Yuzawa City, Akita Pref. in October 1995 twelve years after the Nihonkai Chubu Earthquake (M=7.7) in May 1983. The survey was conducted in terms of 27 items including personality, memory, knowledge/interest, psychology/action, mental attitude/preparations, wishes for researchers and administration, etc. Also included were the items on the Great Hanshin-Awaji Earthquake and the earthquake blank areas. The number of distributed questionnaires and the recovery rate of them are 1500 and 79.2% in Honjo City, and 1700 and 84.7% in Yuzawa City. From the survey, it was found that people have a lot of knowledge of and high interest in the earthquake and well remember it, and a lot of people know of tsunami, liquefaction phenomena, and the earthquake blank area. Further, they are afraid of earthquakes and think of their actions to be taken in case of earthquake. However, most people are little prepared for earthquakes. Important future subjects were suggested for the study of disaster prevention measures. 13 figs.

  20. Evaluation for characteristics of around the Nojima fault; Butsuri tansa ni yoru `Nojima jishin danso` shuhen no jiban bussei ni kansuru ichihyoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K.; Tsuji, T. [Newjec Inc., Osaka (Japan); Tsuji, M. [OYO Corp., Tokyo (Japan)

    1996-05-01

    Various surveys were conducted for the area around the Nojima fault, including ground surface, two-dimensional electrical and boring surveys and elastic wave tomography, in order to grasp properties of the ground around the `Nojima earthquake fault.` The resistivity image method as one of the two-dimensional electrical methods was used to grasp fault shapes over a wide range of the 1.6km long section extending between Esaki and Hirabayashi. The courses of traverse were set in the direction almost perpendicular to the fault. Boreholes were excavated and elastic wave tomography was conducted between the boreholes on the 9th and 17th courses of traverse, to confirm ground/mountain conditions and to compare the results with observed elastic wave velocities. Very low resistivities are observed at places where granite is distributed, suggesting that the fault-induced changes are not limited to the area around the fault. The zone in which elastic wave velocity decreases is narrow, 10m at the longest, at a velocity of 2.4km/s or lower, which is a low velocity for that propagating in granite. 5 refs., 4 figs.

  1. Investigational study on the development, production and wide spread of welfare apparatus in north Europe; Hokuo ni okeru fukushi yogu no kaihatsu seisan fukyu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of grasping the present situation of the development/production/spread of welfare apparatus in north Europe, an investigation was conducted paying visits to Sweden and Denmark. Basically in the Swedish policy for handicapped persons, disablement is defined not only as features which belong to each individual, but as problems arising when the environment surrounding each individual touches one another. Moreover, characteristics of their policies on welfare apparatus are that major welfare apparatus can be provided for the disabled free of charge, and that the government and public organs play a major role in each step of the development, evaluation, distribution and provision of welfare apparatus. Features of the market of welfare apparatus are that users and buyers of the apparatus are different persons, that a public corporation called SUB participates in determining selling prices, etc., and that the market reflects needs and requests from users comparatively naturally. The needs for welfare apparatus at the Research Institute of Handicapped Persons are grasped through opinion exchanges with groups of handicapped persons or information exchanges with the technical aid center. 3 refs., 11 figs., 10 tabs.

  2. Numerical simulation and experiment of supersonic jet impingement on a plate; Heiban ni shototsu suru choonsoku funryu ni kansuru suchi kaiseki oyobi jikken

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N. [Tokyo Univ. (Japan)] Hayashi, K. [Aoyama Gakuin Univ., Tokyo (Japan)] Fujiwara, T. [Nagoya Univ. (Japan)] Arashi, K. [Kumamoto Inst. of Tech., Kumamoto (Japan); Kodama, M. [Mitsubishi Heavy Industries Ltd., Tokyo (Japan)

    1998-09-05

    A large-sized rocket, such as the H-II rocket used in recent years ejects a high-temperature high-pressure jet from the jet nozzle of the rocket to obtain a required level of thrust at the launching. Therefore, the protection of objects such as the rocket body, reflectors and the launcher against the high-temperature high-pressure jet is a problem. In this study, the clarification of the physical phenomenon is attempted by both numerical analysis and experiments in regard to the problem of the impingement of the axisymmetric supersonic jet upon the plate under the atmospheric and non-high-temperature underexpansion conditions. In this report, and analysis of a non-viscous flow which was made so as to examine the effect of the compressibility of a shock wave structure is described. Experiments were then conducted so as to qualitatively and quantitatively examine the results of the numerical analysis. A stagnation bubble forming and breaking mechanism and a complicated structure of the shock-shock interaction were then studied by a numerical analysis by changing the position of the plate. 14 refs., 20 figs., 2 tabs.

  3. Study on the development of flood control techniques in the Niigata plain. Niigata heiya ni okeru chisui gijutsu no henkan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Chino, Y. (Nigata Univ., Nigata (Japan). Graduate School); Okuma, T. (Nigata Univ., Nigata (Japan). Faculty of Engineering)

    1992-01-20

    There are 14 floodways built from the mid-Tokygawa era up to now in the Nigata Plain and the most important and large-scaled one in these is the Okozu floodway. The plan of the Okozu floodway which is playing its wonderful role to control flood may be considered to begin in 1730s, Edo era, but it was not practiced by Tokugawa. The necessity for the Okozu floodway to control flood in the Nigata Plain had been confirmed by the floods happening continuously in the 1880s. The excavation construction was begun in 1909, about 200 years after the plan. The work started by using modern flood control techniques and the floodway came into practical use in 1922. In the present paper, the history of flood control in the Nigata Plain from 1730s to the modern times has been traced. Using the results, the development of the modernization of flood control technique centered at weirs and gates has been studied. 44 refs., 5 figs., 1 tab.

  4. Various discussions on feminine adaptive capability in high-tech labors. (2). Haiteku rodo ni okeru josei no tekiono ni kansuru shokento. (2)

    Energy Technology Data Exchange (ETDEWEB)

    Jindai, M.; Miyake, S.; Hataya, T.; Sato, N.; Matsui, M.; Matsumani, M. (Univ. of Occupational and Environmental Health, Kitakyushu (Japan). Institute of Industrial Ecological Sciences)

    1991-01-01

    The Japanese industrial society is transforming into a post industrial society, accompanying a noticeable orientation to an information society as a result of introduction of the highly advanced technologies (hi-techs) and a rapid change in the labor structure as a result of more entry of women into the society. Therefore, a study was made on the contacts with the hi-techs of women in their labor scenes through an image survey and two kinds of experiment. One of the experiments was conducted on their work burdens and work adaptability when female workers manipulate industrial robots. Another experiment was on effects of feminine physiological periods on image judging work using as a model an inspection work that uses a CRT. As a result, it was revealed that the degree of friendly feeling in female workers toward hi-techs is affected largely by operating duration of hi-tech devices. The result of work and the degree of skillfulness in robot manipulations were higher in men than in women. Very little effects were observed on the feminine physiological periods giving on the image judging work. 36 refs., 5figs., 2 tabs.

  5. Model experiments on imaging subsurface fracture permeability by pulsed Doppler borehole televiewer; Pulse doppler borehole televiewer ni yoru kiretsu tosuisei hyoka ni kansuru model jikken

    Energy Technology Data Exchange (ETDEWEB)

    Inagaki, Y.; Niitsuma, H. [Tohoku University, Sendai (Japan). Faculty of Engineering

    1996-05-01

    This paper reports model experiments to evaluate flow rates of fluids passing through a fracture by using a Doppler borehole televiewer (DBHTV). A supersonic transducer disposed on a well axis transmits transmission pulses, and a transducer receives scattered waves generated by particulates in water and waves reflected on a well wall. This signal is applied with time gating to extract only the scattered waves from particulates in the vicinity of the well wall. Deriving spectra in the recorded Doppler signal obtains flow velocity components in the direction of the well radius. A model was made with a polyvinylchloride pipe with a diameter of 14.6 cm to simulate a well, to which an aluminum pipe with an inner diameter of 2 mm is connected to be used as a simulated fracture, and mud water is circulated in the pipe. The result of deriving a passed flow volume in this model by integrating flow rate distribution derived by using the above method to a predetermined range in the vicinity of the fracture showed a good proportional relationship with actual flow rate in the simulated fracture. 1 ref., 7 figs.

  6. Future subjects on earthquake research in the Geological Survey of Japan; Chishitsu chosasho ni okeru jishin ni kansuru chosa kenkyu no kongo

    Energy Technology Data Exchange (ETDEWEB)

    Kinugasa, Y. [Geological Survey of Japan, Tsukuba (Japan)

    1998-03-01

    For the study of earthquake occurrence potentials attributable to active faults, etc., researches are being made concerning the assessment of hazard due to active faults, monitoring of underground water, explanation of fault shapes and rock fracture mechanism, geological surveys, and the development of methods for evaluating active faults in the sea. As the results, active fault structural charts have been compiled; underground water monitor data have been collected; relations have been disclosed between the occurrence of plural events, change in the number of events, and the sectional shapes of faults, these thanks to fault simulation using rock specimens; part has been completed of geological maps; profiles have been obtained through application of a high-resolution sound source-aided seismic reflection method to active faults in the sea; and a 2-dimensional extensive distortion analysis program has been substantiated. Studies in the future will deal with the disclosure of the history of activities of active faults, paleoseismological surveys, establishment of methods for evaluating the activity of active faults in the sea and for analyzing earthquake-produced sediments, development of technologies for exploring seismic bedrocks in the flatland, preparation of geological charts for observation-enhanced areas and monitoring of underground water in the same, and the basic research into the process of earthquake occurrence

  7. Theoretical study on seaquake loads acting on a two-dimensional floating body; Nijigen futai ni hataraku kaishin kaju ni kansuru rironteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Higo, Y.; Ueno, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Koda, M. [Asahi Glass Co. Ltd., Tokyo (Japan); Nakamori, K. [Nippon Denro MFG. Co. Ltd., Osaka (Japan)

    1996-10-01

    Analyses and discussions were given on characteristics of loads as a result of seaquake acting on a floating body. In the present study, propagation of pressure waves due to vibration in sea bottom ground as propagation of underwater sound waves, and pressures in wave motion fields and loads due to seaquake acting on the floating body were derived by using the Green function which satisfies free surface conditions and sea bottom conditions. In addition, the boundary element method was used to conduct similar calculations to verify the methodological reasonability. As a result of discussions, the following results were obtained: a seaquake load has a resonant point which corresponds to an intrinsic value of the boundary value problem in a closed region; the resonant point moves according to width of the floating body, and the frequency moves to higher frequency side when water depth is shallower; compressibility of fluid cannot be ignored in the vicinity of the frequency for the resonant point; the seaquake load is proportional to width of a vibrating ground on the sea bottom, and the load in the vertical direction decreases when the center of the floating body is separated from the vibrating ground; a load in the horizontal direction presents no problems in a floating body with a shallow draft; and a moment in the lateral direction may present a larger problem than in the load in the vertical direction. 8 refs., 8 figs.

  8. Experimental studies on performance of tandem hydrofoils in high speed regions; Kosokuiki ni okeru tandem suichuyoku no seino ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakatake, K.; Oda, K.; Kataoka, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Okada, S. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Mizuno, S. [Hitachi Zosen Corp., Osaka (Japan)

    1996-10-01

    With an objective to clarify basic performance of hydrofoils, a towing experiment was carried out on single hydrofoil and tandem hydrofoils, whose results are reported in this paper. In the experiment, the tandem hydrofoils are supported on two stays on the left and right sides, and the whole lifting power and the whole drag including those of the stays were measured by using strain gauges placed on four plate springs. Results of the experiment may be summarized as follows: in the case of the single hydrofoil, the lifting power constant varied as a result of strong impact on free surface as the shallower the hydrofoil, but corresponds to the size of the lifting power coefficient in high speed regions; in the case of the tandem hydrofoils, the smaller the submersion depth, the effects grew larger on the lifting power coefficient and the drag coefficient, similarly to the case of the single hydrofoil; and the lifting power coefficient for the leading hydrofoils changes very little as a result of change in horizontal distance between the tandem hydrofoils, but the lifting power coefficient of the rear hydrofoils vibrates due to influence from the leading hydrofoils, with the peak of the value thereof transferring to the higher speed side as the horizontal distance increases. 3 refs., 10 figs., 2 tabs.

  9. Magnetic behavior of HTS bulk in Ac Magnetic Field; Koryu jibachu ni okeru chodendo barukutai no furumai ni kansuru kiso shiken

    Energy Technology Data Exchange (ETDEWEB)

    Oyama, T.; Susa, T.; Tsuda, M.; Ishiyama, A. [Waseda Univ., Tokyo (Japan); Kohayashi, S.; Haseyama, S. [Dowa Mining Co., Ltd., Tokyo (Japan)

    1999-11-10

    As example of the utilization in applying the high-temperature superconductivity bulk body to electrical machinery and apparatus, by magnetizing, the trial used as a permanent magnet has been made the bulk body. However, a capture magnetic flux after the magnetizing of the bulk body receives the effect from the externally applied magnetic field and changes. Therefore, it is considered that that the effect from the variable magnetic field is grasped becomes indispensable for the design of the bulk body application equipment. Then, the result of testing the magnetization characteristic, especially characteristics for frequency and peak value of alternating current external magnetic field, is reported. (NEDO)

  10. Investigational study of the CO2 balance in high temperature CO2 separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    An investigational study was conducted to clarify the adaptable environment and effectivity of technologies of high temperature separation/recovery/reutilization of CO2. In the study, data collection, arrangement and comparison were made of various separation technologies such as the membrane method, absorption method, adsorption method, and cryogenic separation method. With the LNG-fired power generation as an example, the adaptable environment and effectivity were made clear by making models by a process simulator, ASPEN PLUS. Moreover, using this simulator, effects of replacing the conventional steam reforming of hydrocarbon with the CO2 reforming were made clear with the methanol synthesis as an example. As to the rock fixation treatment of high temperature CO2, collection/arrangement were made of the data on the fixation treatment of the CO2 separated at high temperature into basic rocks such as peridotite and serpentinite in order to clarify the adaptable environment and effectivity of the treatment. Besides, a potentiality of the fixation to concrete waste was made clear. 57 refs., 57 figs., 93 tabs.

  11. Hydraulic mechanism of siltation in approach channels and harbors. Siltation ni yoru koroter dot hakuchi maibotsu no suiri kiko ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Irie, I. (Kyushu Univ., Fukuoka (Japan). Faculty of Engineering); Murakami, K.; Tsuruya, H. (Ministry of Transportation, Tokyo (Japan). Port and Harbour Research Inst.)

    1991-11-20

    The phenomena that clay or mud is carried away by waves or currents and deposited in approach channels and harbors are called siltation, and hinder often seriously the navigation of vessels and their arrival at as well as departure from wharves, etc.. In this paper, the hydraulic mechanism of siltation in harbors and approach channels in the sea area is chozen in particular, and waves and currents as the external force governing the travel of bottom mud, the properties of sunken mud, the supply source of sunken mud in approach channels, and grasping of the mud sinking mechanism as well as countermeasures against mud sinking are stated mainly centering around the results obtained from the in situ observations at Kumamoto Port and Banjarmasin Port and their mathematical calculations. The bottom mud traveling mechanism has been accepted as a study subject respectively from such wide viewpoints as river engineering, agriculture, environmental engineering, sanitary engineering, chemical engineering and mechanical engineering, and in addition, it has been under study by coastal engineering. Siltation under the wave actions is still in the state of research even in advanced countries in America and Europe. The siltation research in Japan has a short history, but this is the field which must be coped with positively. 19 refs., 17 figs.

  12. Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

  13. Survey on weather changes associated with large-scale tree-planting. 2; Daikibo ryokuka ni tomonau kiko henka ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    An investigational study was made for large-scale tree-planting aiming at CO2 fixation. Water resource and precipitation relating to tree-planting were determined from NASA data and arranged into the global distribution map. It was found that Australia and the Chinese continent are under the relatively favorable condition. As for the soil condition, nutrition resource is short in the desert and unused zone. From the vegetation data obtained from meteorological satellite NOAA, developed was a method for estimating net primary productivity of terrestrial ecosystem and obtained was a global distribution map for the amount of CO2 fixed under the present terrestrial vegetation. At the same time, areas which have great potentiality of tree-planting were selected from the map for estimating potentiality of the global tree-planting. To study the promotion of rainfall as a means of expanding the potential tree-planting area, the conventional meteorological and physical model was improved, and more realistic simulation was made possible. Also as to the water utilization technology, the modeling method was developed. As the area having a potentiality of expanding tree-planting, Australia (especially the west) was cited as the first candidate, and China the second candidate. 108 refs., 128 figs., 49 tabs.

  14. Global environmental benefits of industrial heat pumps (fiscal 1993); 1993 nendo koon heat pumping gijutsu ni yoru chikyu ondanka keigen koka ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    An investigational study was conducted aiming at making a quantitative grasp of effects of the spread of industrial heat pumps on energy conservation and greenhouse gas reduction and at promoting the spread. Finally, the following eight countries joined this international joint research: Canada, France, Japan, Holland, Norway, Sweden, the U.K. and the U.S. Each country share the work and expenses for the research with each other. Japan made investigational researches on the application of heat pumps to processes of the chemical industry, oil refining industry, food industry, paper/pulp industry, and dyeing/weaving industry, and on the effects of greenhouse gas reduction. As procedures taken, values up to 2010 were estimated of energy prices in each country, energy supply/demand, rates of the heat source configuration for electric power supply, etc., the heat flow of the above-mentioned process was made clear, and analyses were conducted of annual profits, energy consumption, and depreciation period in the case of adopting heat pumps. Moreover, the energy conservation amount and greenhouse effect gas reduction amount were estimated based on the result of the analyses. 69 figs., 196 tabs.

  15. Research of environmental bioecosensing technology using ecological information. Part 2; Seitaikei joho ni yoru kankyo bio ecosencing gijutsu ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Basic considerations of exploring and cultivating environmental reporter organisms are summarized. Mechanism of genetic engineering amplification and molecular biological amplification, and approach to combining them to a hardware as a bioindicator system are investigated. For the current status of molecular biological measurement technology for measuring ecological environment and its application, environmental diagnosis from a phyropathological viewpoint, environmental diagnosis using microorganisms, test fabrication of genetic sensor, and overseas examples of environmental monitoring network are described. For the application of ecological information and functions for developing innovative environmental remediation technology, issues and potential areas for research and development regarding the bioremediation technology in which the US has achieved a progress for the benefit of soil environment remediation are summarized. For the phytoremediation, an area of bioremediation, the metabolism of microorganisms which live in the rhizosphere, and the technology for controlling the microorganisms in the soil through plants are investigated. 66 refs., 50 figs., 17 tabs.

  16. Research on giving antibacteria activity of tailored dental materials; Gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The secondary dental caries easily occur by breeding of bacteria in cavities between living body and composite resin, false tooth or root of tailored tooth as tooth repairing materials. The antibacteria activity of tailored dental materials was thus studied by implanting Ag ion. The antibacteria effect with time after culture of caries bacteria was studied by implanting Ag ion into SiO2 powder, PMMA samples and Ti alloy samples at 20 and 200keV in energy of ion. In addition, the antibacteria activity of SiO2 powder as composite material was found at 25keV which was previously effective for the antibacteria activity. This SiO2 filler (Ag{sup +} filler) showed the antibacteria activity on every bacteria sample after 2h, and in particular, could kill all of 3 kinds of bacteria obtained from a composite resin surface after 12h. The number of living S. salivarius was reduced by half after 12h. The application of the composite resin filler implanted with Ag{sup +} is significant to prevent recurrence of caries. 5 refs., 27 figs., 7 tabs.

  17. Study on recent research trends in the chemical fields; Kagaku bun`ya ni okeru saikin no kenkyu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This research is conducted to search study themes of chemistry expected towards the 21st century. The complex compound in the fundamental chemistry field and the bio-medical materials in the applied chemistry field are taken up. Bio-medical materials are used for the restoration, rehabilitation, and treatment of the organ and the improvement of its functions. For implants such as hearts, anti-thrombin and anti-calcium precipitation effects and high endurance are required. In this field, special copolymers and bio-membrane-emulating surfaces are studied. For artificial organs, hybrid type materials combining cells, and physiologically active and artificial materials are also studied. There are studies on the missile therapy of drugs and DDS (drug delivery system). The complex compounds contain metallic elements, such as Fe, Mn, Co and Cu, and groups known as ligands which combine these metal elements. They can have a variety of stereo-structures and physical properties. They also exhibit a diversity of functions including electron donor bonding, molecular recognition, chemical substitution, and pharmaceutical activity. These features open up a promising potential for their prospective use as physiologically active substances, cancerostats, new materials, artificial photosynthesis, memory elements, and complex catalysts. 88 refs., 35 figs., 6 tabs.

  18. Study on solar and human power hybrid drive system applied to electric wheelchair; Dendosha isu ni tekiyosuru taiyo denchi jinriki hybrid kudo system ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, Y.; Uchijima, T.; Saijo, T. [Shibaura Institute of Technology, Tokyo (Japan)

    1994-12-08

    In order to control, with high efficiency, the solar and human power hybrid drive system, the solar cell capacity and condenser capacitance were studied for the brushless DC motor. As an energy storage source, condensers were used in parallel in lieu of battery. In the steady state, the energy generated by the solar cells is used for the driving, while its shortage is compensated from the condensers against the start-up and other cases of much energy required. If the condenser capacitance is small, the start-up is delayed. If it is extremely large, the required time is prolonged for the charging and discharging, the weight increases, and the follow-up performance falls. Judging from the working points (voltage and current) required for the solar cells during the rated operation, 13 modules gave an appropriate capacity, while the appropriate condenser capacitance was 2424 micron F. When a rotational frequency of 2500rpm was inputted, sufficiently smooth torque characteristics were given as start-up characteristics with a good follow-up performance and appropriate condenser capacitance. Judging from the working points during the rated operation, the solar cell capacity was also appropriate. 2 refs., 10 figs., 2 tabs.

  19. Coal liquefaction in early stage of NEDOL process 1t/d PSU; 1t/d PSU ni okeru ekika shoki hanno ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, K.; Kawabata, M.; Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

    1996-10-28

    To investigate the behavior of coal liquefaction reaction in early stage as a part of studies on the coal liquefaction characteristics using NEDOL process 1 t/d process supporting unit (PSU), coal slurry sample was taken from the outlet of slurry preheater located in the upflow of liquefaction reactors, and was tested. Tanito Harum coal was used for liquefaction. Preheater was operated under the condition of pressure of 170 kg/cm{sup 2}, gas flow rate of 64 Nm{sup 3}/hr, and at temperature up to 410{degree}C at the outlet, in response to the standard test condition. The slurry sample was discharged into a high temperature separator with temperature of 250{degree}C. Liquefaction was not proceeded at the outlet of preheater. Solid residue yielded around 80%, and liquid yielded around 15%. Gases, CO and CO2, and water yielded also small amount around 3%. The solid sample contained much IOM fraction (tetrahydrofuran-insoluble and ash), and the liquid contained much heavy oil fraction. Hydrogenation was not proceeded, and the hydrogen consumption was very low showing below one-tenth of that at the usual operation. Hydrogen sulfide gas was formed at early stage, which suggested that the change of iron sulfide catalyst occur at early stage of liquefaction. 1 ref., 5 figs., 2 tabs.

  20. Investigation of the deposit formation in pipelines connecting liquefaction reactors; 1t/d PSU ni okeru ekika hanno tokan fuchakubutsu no seisei yoin ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Y.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-28

    The liquefaction reaction system of an NEDOL process coal liquefaction 1t/d PSU was opened and checked to investigate the cause of the rise of differential pressure between liquefaction reactors of the PSU. The liquefaction test at a coal concentration of 50 wt% using Tanito Harum coal was conducted, and it was found that the differential pressure between reactors was on the increase. By the two-phase flow pressure loss method, deposition thickness of deposit in pipelines was estimated at 4.4mm at the time of end operation, which agreed with a measuring value obtained from a {gamma} ray. The rise of differential pressure was caused by deposit formation in pipelines connecting reactors. The main component of the deposit is calcite (CaCO3 60-70%) and is the same as the usual one. It is also the same type as the deposit on the reactor wall. Ca in coal ash is concerned with this. To withdraw solid matters deposited in the reactor, there are installed pipelines for the withdrawal at the reactor bottom. The solid matters are regularly purged by reverse gas for prevention of clogging. As the frequency of purge increases, the deposit at the reactor bottom decreases, but the deposit attaches strongly to pipelines connecting reactors. It is presumed that this deposit is what Ca to be discharged out of the system as a form of deposition solid matter naturally in the Ca balance precipitated as calcite in the pipeline connecting the reactor. 3 refs., 5 figs., 4 tabs.

  1. Ni hombres ni mujeres providenciales

    OpenAIRE

    Montaño Virreira, Sonia

    2000-01-01

    Debo advertir a la y el lector de este texto que lo que a continuación se presenta no es, ni de lejos, una propuesta realista, si por ella entendemos la traducción, enclave mujer, de las actuales tendencias de liderazgo político vigentes en la región. Por el contrario, intento argumentaren favor de un liderazgo que supere el caudillismo como estilo y se aproxime al máximo hacia el respeto de las formas, entendiendo que sin ellas no es posible construir la democracia. Para hacerlo reviso rápid...

  2. Fluctuation of the accumulation rate of aerosol in the Hess rise, North pacific, during the last 200 kyr: estimation of aerosol effect to carbon cycle; Kitataiheiyo chu ido iki no Hesu kaibo ni okeru kako 20mannen no fusojin no chinseki hendo to tanso junkan ni ataeta eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kawahata, h. [Geological Survey of Japan, Tsukuba, Ibaraki (Japan); Matsumoto, E. [Nagoya Univ., Nagoya (Japan). Water Research Inst., Nagoya; Ito, Y. [Univ. of the Ryukyus, Okinawa (Japan). Lab. of Oceanography

    1997-05-15

    A sedimentary core recovered from the Hess Rise underlying directly below the westerly wind system in the mid-latitude of the North Pacific provides a detailed record of terrestrial and marine environments during the last 20kyr. Most of the aluminosilicate in the sediments are considered to have been transported through the atmosphere by wind. The mass accumulation rates (MARs) of aerosol quarts increased during stage 2 and middle stage 6, and showed maximal during stage 4. A little terrestrial organic substances must have been transported accompanying aerosol quarts, but most of the organic substances seem to be mostly of marine origin because Corg/N ratio of the organic substances contained in the sediments is 7.4. The phosphorus supply to the sea surface transported by aerosol quarts can be presumed to have a large latent potential to the accumulation of organic carbon. The effect of calcium carbonate supply into the sea surface by aerosol quartz on diminishing CO2 partial pressure in the surface water is found to be only less than 1{mu}atom/year. 55 refs., 6 figs.

  3. Study on the optimal control of the ground thermal storage system in the greenhouse. Part 4; Onshitsu ni okeru taiyo energy dochu chikunetsu system ni okeru saiteki seigyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, M. [Sanko Air Conditioning Co. Ltd., Osaka (Japan); Nakahara, N. [Kanagawa University, Yokohama (Japan)

    1996-10-27

    Three types of weight in both energy saving and optimum room temperature environment were changed to obtain the optimal control solution of the ground thermal storage system in a greenhouse. The relation diagram between the optimal solution of a performance function, and the state constraints and control function constraints was created in consideration of the energy term in a control function value area and the room temperature environment. As a result, the whole image of the performance function could be grasped in consideration of the energy term with inequality constraints and the room temperature environmental term in this study. The rate of a weighting factor in the performance function significantly influences the optimal solution. The influence on the optimal solution also changes when the optimal room temperature schedule differs. The influence that three types of rising algorithm exert on the convergence and converging speed was investigated. Superiority or inferiority occurs according to the space properties of a performance function. A zigzag method is most disadvantageous. The constraints can be converged to the optimal solution using an SUMT outer point method irrespective of the initial value. 6 refs., 6 figs., 4 tabs.

  4. Studies on reduction of fluid drag for athlete swimming suit by boundary layer control; Kyoeiyo mizugi ni kansuru kenkyu (kyokaiso seigyo ni yoru mizugi teiko no sakugen ni tsuite)

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Y. [Mie University, Mie (Japan). Faculty of Engineering; Suzuki, T. [Mie University, Mie (Japan); Mori, K. [Mizuno Corp., Osaka (Japan)

    1998-09-25

    Sport science progresses step by step in the world. The paper describes, the first, the relationships between fluid drag for a model of woman swimmer and the flow around it. The flow around the model swimmer is very complicated, and includes, for example, wave, some kinds of vortices, hydraulic jumping and so on. The complicated flows are visualized by the surface tufts method and so on. Second, the possibility of the reduction of fluid drag for a woman athlete swimming suit is challenged. The boundary layer control is applied to reduce the fluid drag. The separation occurs around the breast of a woman swimmer. The separation can be suppressed by the boundary layer control. Many beads are distributed on the breast area of a woman swimming suit. As the result, it is found that the fluid drag for the model swimmer can be reduced in a range of 1.5%--2% by the suit with the boundary layer control, which is carried out by many beads. 2 refs., 12 figs., 3 tabs.

  5. Report on the achievements in fiscal 1999. Technology to use gas hydrate as a resource (Research and development for exploration, research and development on drilling technologies, investigative research on an environment influence evaluation method, and investigative research on a utilization system); 1999 nendo gas hydrate shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansa nado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The contents of the research and development performed in the current fiscal year are as follows: (1) research and development for exploration, (2) research and development on drilling technologies, (3) investigative research on an environment influence evaluation method, and (4) investigative research on a utilization system. In Item (1), element analysis data are used to study a method to estimate production environment of hydrate ore beds by using an inorganic ion analyzer and a trace amount element analyzer, the crust thermal flow measuring method is used to discuss a method to analyze the hydrate stability zones together with the data of sea area exploration records, and conceptual design is made on a resource potential evaluation system. In Item (2), experiments and analytical discussions are performed on decomposition control of the gas hydrate solid-liquid interface according to such conditions for the drilling fluid as temperatures and flow rates. Elucidation is given on the initial process of bubble generation for behavior of decomposed gas bubbles. Observation and elucidation are made on two-phase flow behavior of non-Newtonian fluid. In Item (3), conceptual design is carried out on a system to detect elements of shape change in each bed due to fluid movement in a gas hydrate bed and an upper bed. In Item (4), discussions are given on the optimizing conditions for generation and dissociation of gas hydrates. Investigation is made also on a possibility of the transportation and storage system. (NEDO)

  6. FY 1998 annual report on the preliminary research and development of techniques for developing resources from gas-hydrate. Studies on gas-hydrate exploration, excavation techniques, methods for assessing environmental impacts, and gas hydrate handling systems; 1998 nendo gas hydrate shigenka gijutsu sendoken kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu nado ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no kenkyu kaihatsu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D project is for the preliminary studies on development of the following 4 types of techniques for developing resources from gas-hydrates (GH): (1) gas-hydrate exploration, (2) excavation techniques, (3) methods for assessing environmental impacts, and (4) gas hydrate handling systems. The FY 1988 R and D results are described. For gas-hydrate exploration, the methods for analyzing inorganic ions and trace quantities of elements, which are necessary for accurately estimating the offshore GH around Japan, are established; and case studies are conducted for methods of predicting GH deposit forming mechanisms, and stability fields of GH, based on terrestrial heat flow and seismic data. For excavation techniques, GH decomposition rate is analyzed using a laboratory system which reproduces conditions of excavation of GH layers. For methods for assessing environmental impacts, a geo-hazard predicting model is established, to study ground displacement and gas leakage sensing systems and data transmission systems to cope with the hazards. For gas hydrate handling systems, an overall system is studied, and storage and transportation systems are outlined. (NEDO)

  7. Achievement report for fiscal 1997 on the research and development to lead to gas hydrate using technology. Research and development on exploration, research and development on drilling technologies, survey and research on a method to evaluate environmental impact, and survey and research on a utilization system; 1997 nendo gas haidoreto shigenka gijutsu sendo kenkyu kaihatsu seika hokokusho. Tansanado ni kansuru kenkyu kaihatsu, kussaku gijutsu ni kansuru kenkyu kaihatsu, kankyo eikyo hyokaho no chosa kenkyu, riyo system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    The present study is intended to analyze comprehensively geophysical, geological and geochemical data, and establish a technology to estimate distribution of gas hydrate (GH) in sea areas around Japan. It is also intended to develop a high-accuracy resource amount calculating method utilizing the result of excavation of GH planned in the future. In order to achieve these goals, the following activities are performed: (1) study on a method to estimate production environment of GH deposits, (2) development of a method to estimate GH stability areas by using the crust thermal flow measuring method, and (3) study on estimation of GH distribution and wide-area potential. For the study (1), an inorganic element analyzer was introduced, and calibration of devices was performed in fiscal 1997. A survey was carried out on literatures related to distribution of inorganic elements and process of GH deposit production. In the study (2), design and trial fabrication were executed on a high-accuracy crust thermal flow measuring device, capable of long-term continuous observation. In the study (3), re-processing focusing on BSR was implemented by using the latest computer and analysis software on the data in which BSR has been confirmed in the surveys done in the past on sea areas around Japan. (NEDO)

  8. Studies on the air distribution and thermal performance of the air circulation wall. Part 4. Study on the thermal emissivity of the air circulation layer`s surfaces; Gaidannetsu tsuki koho ni okeru tsuki sonai no netsu tsuki tokusei ni kansuru kenkyu. 4. Tsuki sonai hyomen no hosha tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kamimori, K.; Sakai, K.; Ishihara, O. [Kumamoto University, Kumamoto (Japan)

    1996-10-27

    The thermal and air distribution characteristics of the air circulation wall in a heat-insulated system were grasped using an experimental model. In this paper, the difference in the heat exchange between the wall and air was confirmed based on the radiation on the circulation layer`s surface. In this system, thin air circulation layers with ventilating holes at the top and bottom are attached to the south and north outer walls of a wooden building. This system is a kind of passive solar house that achieves the insolation screening effect and the temperature rising effect based on solar collection. The heat flow in a circulation layer is eliminated by the natural convection heat transfer on the outer wall. The heat flow passing through insulating materials is the heat transfer by radiation. The heat flow based on the in-layer natural convection is increasingly eliminated by the decrease in temperature on the air circulation layer`s surface. The decrease in room surface temperature using aluminum foil and the reflective heat-insulated effect showed that the heat passing through the wall surface decreases as the convection heat transfer in an air circulation layer increases. 6 refs., 20 figs., 3 tabs.

  9. Study on accident reconstruction model. Validation of the model; Shototsu jiko saigen no kaiseki moderu ni kansuru kenkyu. Moderu no kensho

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, H.; Wei, Lang [Japan Automobile Research Inst., Tokyo (Japan); Nakatsuji, T. [Hokkaido Univ., Sapporo (Japan). Faculty of Engineering

    1995-10-01

    In a vehicle collision accident analysis, the behavior of the vehicle immediately before and after the occurrence of the accident is presumed from the situation of the accident site such as the tire marks remaining at the site, the condition of the body deformation, the last position of the vehicle`s stoppage, etc.. The vehicle collision accident analysis is called also the accident reconstruction, and various analytic models have been proposed, but many of them are analytic models to presume, prior to the collision, the situation after it, and models which analyze the pre-collision situation from the situation after it are not many. In this study, an accident analytic model has been prepared which can reconstruct the vehicle`s speed prior to the collision and its behavior after it only from the stoppage position of the vehicle after the collision and the position of the vehicle at the point of collision by adapting the law of conservation of momentum and the Gim`s tire model. In other words, each analytic equation of the momentum analytic model immediately after the collision, the two-dimensional vehicle movement, the dynamic model, and the verification model of the speed immediately before the collision have been roughly explained and by comparing 5 examples of the experimental results of actual vehicles` collisions with the analytic calculation results of the above model, the validity of the above model has been verified. 4 refs., 6 figs., 1 tab.

  10. Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, K.; Sawada, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

  11. Bayesian reliability analysis for non-periodic inspection with estimation of uncertain parameters; Bayesian shinraisei kaiseki wo tekiyoshita hiteiki kozo kensa ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Itagaki, H. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Asada, H.; Ito, S. [National Aerospace Laboratory, Tokyo (Japan); Shinozuka, M.

    1996-12-31

    Risk assessed structural positions in a pressurized fuselage of a transport-type aircraft applied with damage tolerance design are taken up as the subject of discussion. A small number of data obtained from inspections on the positions was used to discuss the Bayesian reliability analysis that can estimate also a proper non-periodic inspection schedule, while estimating proper values for uncertain factors. As a result, time period of generating fatigue cracks was determined according to procedure of detailed visual inspections. The analysis method was found capable of estimating values that are thought reasonable and the proper inspection schedule using these values, in spite of placing the fatigue crack progress expression in a very simple form and estimating both factors as the uncertain factors. Thus, the present analysis method was verified of its effectiveness. This study has discussed at the same time the structural positions, modeling of fatigue cracks generated and develop in the positions, conditions for destruction, damage factors, and capability of the inspection from different viewpoints. This reliability analysis method is thought effective also on such other structures as offshore structures. 18 refs., 8 figs., 1 tab.

  12. FY 1998 report on the results of the technology development on the integration of nerve information; 1998 nendo shinkei joho togo ni kansuru gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This R and D aims at developing the interface system including 2D multipoint high density electrode elements which measure and analyze the information processing process of cranial nerves at high speed and in minute detail. The R and D were carried out on the following 4 subjects: 1) development of 2D high density multipoint electrode; 2) development of alignment/bonding technology; 3) development of technology for existence maintenance/activation of nerve cells; 4) study of performance evaluation and applicability of the system. In 1), an electrode is developed in which the high density multipoint platinum electrode was built on glass substrate, and the following are conducted: making a pattern of alignment of this electrode, making the shape of electrode 3D, and technical development of surface composition. In 2), the following are developed: technology to align cells on the patterned electrode element correctly and technology to bond cells on the element for a long time. In 3), the following are developed: functional materials to hold living nerve cells/nerve systems on the electrode element for a long time, nutrition system, and technology to monitor the state of cells/systems on the substrate. In 4), conducted are the evaluation of performance of the developmental system and the applicability to the screening in nervous function molecular search, etc. (NEDO)

  13. Studies on surface structures and mechanism of photocatalytic action of semiconductor oxides; Handotai hikari shokubai no hyomen kozo seigyo to sayo kiko kaimei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, H.; Sona, S.; Koike, H.; Hori, H.; Negishi, N.; Kohara, H.; Ibusuki, A. [National Institute for Resources and Environment, Tsukuba (Japan); Vakhtin, A.; Borovkov, V. [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Studies are made to define the working mechanism of semiconductor photocatalysts such as TiO2 and to establish designing guidelines for improving on their activity and functions. TiO2 in the air actively produces oxygen seeds for the oxidation and removal of NOx, etc. It is desired that a catalyst have a specific surface area large enough to retain the product of its action. To meet the need, a thin-film photocatalyst which is an aggregate of TiO2 crystals is produced by burning a film of a sol/gel system of reaction doped with macromolecules. This product has a larger specific surface area and is higher in pollutant-removing performance, and may be put into practical use. In another experiment, metal-carrying particles TiO2 suspended in water are employed for the reduction of CO2. Though the main product of catalysts carrying Pt or Pd is methane, a photocatalyst carrying RuO2 produces acetic acid mainly and loses less activity with the passage of time. A hybrid photocatalyst is composed of an organic pigment and inorganic semiconductor, synthesized through a covalent bond between a sililated-surface thin TiO2 film and porphyrin. It is confirmed that the newly developed process brings about an increase in electron migration efficiency. 3 figs.

  14. Study on property-gradient polymer electrolyte for rechargeable lithium batteries; Lithium niji denchi no tame no keisha tokusei kobunshi denkaishitsu no sosei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kokumi, Z.; Kanemura, S.; Inaba, M.; Takehara, Z.; Yao, K.; Uchimoto, Y. [Kyoto University, Kyoto (Japan)

    1997-02-01

    This paper describes the fundamental experiments for creating property-gradient polymer electrolyte for rechargeable lithium batteries. The rechargeable lithium battery is composed of an anodic composite agent section with high ion conductivity, a separator equivalent section with high mechanical strength (high bridging degree), and a section surpressing the precipitation of metal lithium by contacting with it. The continuous property-gradient polymer electrolyte was tried to be synthesized by means of the plasma polymerization method. As a result, plasma polymerization electrolyte with high ion conductivity could be prepared from the liquid phase by using a monomer with low vapor pressure. Porous material simulating the anodic composite agent was impregnated by the monomer, which was plasma-polymerized. As a result, it was found that the bridging degree decreased from the surface towards the inside of the plasma-polymerized porous material. In addition, polymer was prepared using fluorine-base monomer. Thus, LiF thin film could be prepared through the reaction between the polymer and metal lithium. 3 figs.

  15. Survey of pollution-resistant plants and their cultivating techniques; Osen busshitsu taisei shokubutsu to sono shokusai gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The reduction of forests due to environmental pollution has been surveyed, to investigate the pollution-resistant plants and solid microorganisms. In Japan, the blight of needle-leaf trees (pine and momi fir) and of Japanese oak has occurred, and blight of some other trees, such as wild cherry trees, Japanese apricot trees, birch, Japanese cedar, cypress and bamboo, has been reported from various regions. In this article, plants reported to be resistant to pollutants are listed, and the physiological features of these plants are described. Furthermore, to develop pollution-resistant plants, reports relating to clarification of the mechanism of resistance development and the genes involved are reviewed. Microorganisms which symbioses for roots support these root functions. They also suppress the activity of pathogenic microorganisms and improve the environment around the roots, thus helping plants to grow normally. The roles played by symbiotic microorganisms and how to utilize these organisms are discussed. Their functions in coping with acid rain and heavy metal pollution, and how to utilize such functions are also discussed. 707 refs., 13 figs., 13 tabs.

  16. Research and development of system to utilize photovoltaic energy. Survey on the specific purpose modules; Taiyoko hatsuden riyo system no kenkyu kaihatsu. Taiyoto module ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the survey results on the specific purpose modules for photovoltaic power generation in fiscal 1994. (1) On the feasibility survey on new application fields, it was clarified that photovoltaic power generation is applicable to extensive areas such as farmland, road, railway and public facility as latent demand sites. (2) On the optimum modules for various specific purposes, the structure, production method, cost estimation and issues of various modules were studied for desert, wasteland, coast, ocean, river, embankment, railway, road, mobile facility and arcade. (3) On the survey on new materials and material development, various conventional materials and materials promising for required performance were surveyed for every application. (4) On the survey on technology trends, the survey members participated in the first international photovoltaic energy conversion conference and the photovoltaic power generation workshop, while the members held the 1st-5th specific purpose module subcommittees. 1 tab.

  17. FY 1998 annual report on the research and development of superhigh-sensitivity photocurrent conversion devices; 1998 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are research and development of superhigh-sensitivity photocurrent conversion devices. The huge photocurrent multiplication effect exhibited by a thin film of organic pigment semiconductor is expected to be applicable to various new devices, e.g., superhigh-sensitivity, intelligent optical sensor families and photocurrent devices. Photocurrent multiplier thin films of perylene is prepared by an ionized cluster beam method, to evaluate their structures and photocurrent characteristics as the basic knowledge for controlling their characteristics by the ion engineering procedures. Photocurrent multiplier thin films of new, two-layer structure are developed, and improvement and stabilization of their characteristics are studied. Increasing sensing sensitivity by, e.g., introduction of p-n junction and reducing dark current resulting from the light memory effect are found to be effective to improve the S/N ratio. An organic EL light-emitting layer capable of positive/negative feedback, as one of the elementary techniques for realizing intelligent devices, is made on a trial basis and evaluated for its characteristics, and studied for its application to photocurrent multiplier thin films. Functional devices in which the arithmetic and controlling functions of the thin films are utilized are also studied. (NEDO)

  18. Studies on hollow spherical aluminum silicate cluster. Synthesis of environment friendly materials; Chuku kyujo aluminium keisan`en cluster ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ohashi, F.; Maeda, M.; Suzuki, M.; Watamura, S. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

    1999-01-25

    Synthesis of microfine particles of nanometer size, their surface adulteration and control of microstructure take an important position in different areas, such as electronics, chemical, machine and metal industries. However, reports on the established methods for synthesizing hollow spherical particles of nanometer size, which may be applied to micro capsules, cannot be found except for fullerene composed of carbon. This paper introduces a new method for synthesizing hollow spherical amorphous aluminum silicate cluster called allophane as an earth environmental material, and the derived properties of allophane. (translated by NEDO)

  19. Investigational research on CO2 isolation technology in fiscal 1995; 1995 nendo nisanka tanso no kakuri gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper studied present technical subjects and future study subjects of the CO2 isolation technology in order to clarify technical and social problems and the developmental subjects of the CO2 isolation technology and related technologies for separating/concentrating CO2 emitted in relation to quantity consumption of fossil fuel and storing it in ocean or underground. Main items for the study were: (1) investigational study of the technology of CO2 ocean storage, (2) investigational study of environmental effect assessment in storing CO2 in ocean, (3) investigational study of the technology of CO2 ocean storage, etc. Technologies required for the ocean isolation were arranged such as CO2 storage, injection, dispersion technique, CO2 behavior simulation, and the developmental subjects were extracted. Further, in the deep-sea bottom storage method, a simulation to calculate the range of PH effects was conducted presuming the specified amount of CO2 and applying known physical values, and evaluation of the CO2 ocean discharge/solution method was made. A method was also studied for experiments on water bacteria and benthos. 127 refs., 102 figs., 81 tabs.

  20. Studies on connecting structure between steel shell and steel reinforced concrete; Kokaku to tekkotsu tekkin concrete tono ketsugo kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Morimoto, A. [Kinki University, Osaka (Japan). Faculty of Science and Engineering; Morikawa, H.; Ito, N. [Metropolitan Expressway Public Corp., Tokyo (Japan)

    1996-02-15

    On the insert reinforcing bar structure for the connecting part of the main tower of cable stayed bridges, this paper reports verification results on a load resistant safety with a full-scale model, structure analysis and construction work. The basic structure was composed of a drilled steel shell, inserted reinforcing bars, fixing structure of bars in lining concrete of the shell and a pressure bearing plate. As an experimental result, the connecting part had a sufficient load carrying capacity against both tensile and compressive loads. The shear stress of the insert reinforcing bar structure was estimated successfully under von Mises`s condition. The shear spring constant in deformation characteristics was linearly proportional to an inserted reinforcing bar ratio. In earthquake, nearly 60% of an allowable compressive load was transferred to concrete through the pressure bearing plate. The analytical results of load resistant deformation characteristics of the connecting part well agreed with experimental ones, and the proposed analytical model was applicable to estimation of a dynamic behavior. 5 refs., 22 figs., 4 tabs.

  1. Some studies on structural planning of long-span cable stayed bridge; Choshikan shachokyo no kozo keikaku ni kansuru 2,3 no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Endo, T. [NKK Corp., Tokyo (Japan)

    1997-06-20

    Feasibility of cabled-stayed bridges with 1000m-grade spans is discussed while re-examining the plan for constructing a Great Tatara Bridge to connect Honshu and Shikoku, Japan, and in this process various tasks and questions are isolated. Some which will be problems in designing the new bridge structure are taken up, including the load-bearing capability of the bridge as a whole, vibration of long cables, resistance to long-period earthquakes, and accuracy management during the construction work. Findings are stated below. A cable-stayed bridge is not significantly different from a suspension bridge and is sufficiently feasible until the span exceeds 1500m. When the span is longer, however, the bridge beam cross section needs be designed very prudently in view of the great axial force and wind load to be imposed on it. Effective for the assurance of load-bearing capability for a long-span cabled-stayed bridge is a structure in which load is elastically confined in the direction of the bridge axis. In connection with vibration damping for very long cables, it is verified that a new dimpled cable suits the purpose of suppressing wind load from increasing without reduction in damping effect. 28 refs., 23 figs., 7 tabs.

  2. Proposal of self-anchored cable-supported bridge with main span length of 500m; Chuo span 500m kibo no jiteishiki tsurigatashiki kyoryo ni kansuru teian

    Energy Technology Data Exchange (ETDEWEB)

    Fukasawa, Y.; Sugiyama, T. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering; Kaneko, S.; Mukoyama, T.; Iwaki, T. [Pacific Consultants K.K., Tokyo (Japan)

    1995-12-15

    In order to investigate the feasibility of construction of cable-supported bridge at the site where ground condition is poor and/or air route restriction shoed be considered the static and dynamic characteristics of both self-anchored cable-stayed bridge with relatively low tower and self-anchored suspension bridge have been discussed. The main span length of bridge considered here is about 500 m because of the fact that stress resultant of main girder caused by design loads is considerably lower than its design strength in the existing cable-supported bridges of this scale. The result shows that the application of both types of cable-supported bridges to the above described site may be possible as enough static safety and economy are ensured. It has been also revealed that no problem may occur from both wind and earthquake resistant viewpoints. 10 refs., 24 figs., 8 tabs.

  3. Experimental study on buckling and ultimate strength of thin-walled box stub columns; Usuniku hakogata danmen buzai no zakutsu / shukyoku kyodo tokusei ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Nakai, H.; Kitada, T. [Osaka City Univ. (Japan); Oryu, T. [Kawasaki Heavy Industries Ltd., Kobe (Japan)

    1998-10-21

    Thin-walled box stub columns such as beams of cable-stayed bridge, suspension bridge tower, arch rib of arch bridge and steel piers and so forth can also bear torsion at the same time besides compression and bending. These thin-walled box stub columns may achieve ultimate condition before reaching to plastic condition due to the effect of local buckling and so forth. Accordingly, it is the important topic to study the properties regarding ultimate strength of thin-walled box members in order to evaluate correctly the effect on load bearing resistance of local buckling. In this report, validity of load bearing resistance curve and ultimate strength interaction curve proposed by authors was studied using load bearing capacity experiment results. As a result, all ultimate strengths obtained by the experiment were higher than the ultimate strengths estimated by load bearing capacity curve and ultimate strength interaction curve. Further, it was revealed that the specimens subjected to torsion or subjected to bending and torsion and so forth exceeded the plastic strength due to the effect of strain hardening. 12 refs., 14 figs., 4 tabs.

  4. Ultimate strength analysis of long-span cable-stayed bridges; Chodai chachokyo no shukyoku kyodo kaiseki to kyodo ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Xie, X.; Yamaguchi, H. [Saitama Univ., Urawa (Japan)] Nagai, M. [Nagaoka Technical Coll., Niigata (Japan)

    1998-07-21

    Recently, span of cable-stayed bridges has been getting loner and longer, present situation is that cable-stayed bridges with span 600 to 800m class have been built inside and outside the country, and accurate determination of its ultimate strength has been an important problem statistically. However, concrete design method for evaluating load bearing stress of long-span cable-stayed bridge. Particularly of the main beam whose axial stress is dominating, has not been established so far. As for cable-stayed bridge, even for long-span, effect of plasticization of cross section on ultimate strength is severe because there is little effect of geometric nonlinearity and it is thought that accurate evaluation of ultimate strength only by elastic finite potential analysis is difficult. Accordingly, it is necessary to study the behavior by using combined nonlinear analysis considering the nonlinearity of the material in order to evaluate the safety and economy to long-span cable-stayed bridge. In this report, 3 dimensional analysis method was formularized taking into account the combine nonlinearity of multi-box girder and analysis program of ultimate strength behavior of long-span cable-stayed bridge was developed. 19 refs., 17 figs., 2 tabs.

  5. Evaluation of damping property of long-span prestressed concrete cable-stayed bridges; Chodai PC shachokyo no gensui tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamanobe, S.; Niihara, Y.; Minami, H.; Kono, T. [Kajima Corp., Tokyo (Japan)

    1999-09-30

    As to the dynamic design in the antiseismic design of PC cable-stayed bridges, evaluation of damping is important. Since it is difficult to evaluate damping property theoretically and analytically, a lot of studies have not been made about how to set up damping coefficients. In this study, using analytical models of existing long-span PC cable-stayed bridges, to clarify causes of damping of long-span PC cable-stayed bridge, the rate of strain energy in each member was examined. Equivalent damping coefficients of each member, effects of friction in movable bearing, and effects of basically radiational damping were studied. The correspondence with the results of the vibration experiments conventionally made were studied. (translated by NEDO)

  6. Analysis and model-tests on vortex-induced oscillation of bridges; Kyoryo no uzu reishin ni kansuru sanjigen oto kaiseki to fudo jikken

    Energy Technology Data Exchange (ETDEWEB)

    Yamamura, N. [Hitachi Zosen Corp., Osaka (Japan); Ogasawara, M. [Kansai Electric Power Co. Inc., Osaka (Japan); Shiraishi, N. [Maizuru College of Technology, Kyoto (Japan); Nanjo, M.

    1996-07-21

    In order to predict the three-dimensional response to vortex-induced oscillation of bridges, a model was investigated using the aerodynamic force coefficient including vortex-induced and self-excited forces, and the nonlinear response coefficient expressing constancy of response to vortex-induced oscillation. In the analysis, change of frequency in wind by the self-excited force, aerodynamic damping term, effect of the mode, and correlation of the vortex-induced force along member axis were taken into account. The aerodynamic force and nonlinear response coefficients were identified from the homogeneous and turbulent flow results of wind tunnel tests using a two-dimensional spring support rigid body model with varied damping factor. The aerodynamic damping term can be estimated from the nonlinear aerodynamic force coefficient, but it was enough to calculate it from the quasi-stationary coefficient in general bridge profiles. The correlation of the vortex-induced force was obtained from measurements of the vertical variation components of trailing flow under the resonance state, or the pressure distribution of the member surface. When comparing to the wind tunnel test of three-dimensional model of cable-stayed bridge, the response amplitude by the present analysis method was consistent well with the test results rather than by the method in which the amplitude of two-dimensional model was corrected. 10 refs., 4 figs., 3 tabs.

  7. Investigational study of optical function materials for two-dimensional data processing; Nijigen joho shoriyo hikari kino zairyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper investigated/studied `space light modulation materials,` `dynamic hologram/memory materials,` `optical waveguide path materials,` etc. which become key materials in the high speed two dimensional processing. As to electrooptical materials proposed in this investigational study, the external electric field and the electric charges generated make quality of molecules themselves directly change to memory strong/weak signals of light. Therefore, the response velocity becomes less than a millionth of that of the liquid crystal display, and high speed which is needed for realtime moving image processing is anticipated. Hologram includes the phase information in addition to information on light strength. Therefore, it is a large capacity record medium and at the same time a record medium which can read/write two dimensional information as it is. With optical fiber, images cannot be transmitted as they are. Light waveguide path materials are those that accumulate roles of mirror and lens in a sheet of the material and construct a system which is strong in vibration, as optical parts connecting among materials for two dimensional data processing. 273 refs., 107 figs., 17 tabs.

  8. Feasibility design of a floating airport and estimation of environmental forces on it; Futaishiki kuko no sekkei to kankyo gairyoku no suitei ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, Y.; Tabeta, S.; Takei, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering

    1996-12-31

    A rough design was performed on a floating airport. On this floating structure, environmental external force was estimated, mooring design was carried out, and discussions was given on the position retaining performance important for airport functions and behavior of the floating structure. The discussion was given on cases that the airport is surrounded and not surrounded by floating breakwaters. A floating structure which becomes super-large in size requires considerations on force due to sea level gradient as a result of a tide. Deriving flow condition changes and force acting on the floating structure simultaneously by using numerical calculations makes it possible to estimate current force given with considerations on influence of the flow conditions created by installing the floating airport. Estimation was carried out by using a zone dividing method on wave drifting force acting upon the floating airport. As a result, it was found that installing floating and permeating type breakwaters can reduce the wave drifting force acting on the floating airport. The wave drifting force working on the floating airport can be reduced by installing the floating and permeating type breakwaters to lower levels than when no such breakwaters are installed. The airport may be moored with less number of fenders when the fenders of the same type are used. 18 refs., 10 figs., 5 tabs.

  9. Survey on the feasibility of high-efficiency gas turbine power generation system; Kokoritsu gas turbine hatsuden system ni kansuru jitsuyo kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For higher-efficiency power generation cycle plants with less restrained conditions for a location, the conceptual design of an inter-cooled regenerative two-fluid cycle plant (ISTIG) was attempted using a modified aircraft gas turbine. A high-performance turbo fan engine is used for middle-class power generation. The first stage combustion gas drives the first stage turbine, and its exhaust gas is used for the second stage combustion. Because of two-axial type of high and low pressure, improvement of thermal efficiency is expected by easy-to-install inter-cooler. ISTIG superior in operability is suitable for medium load or distributed power generation facilities, and aims at higher efficiency of a 60% level. ISTIG includes a large amount of water vapor in combustion air by adopting a diffusion type combustor eliminating back fire, and can reduce exergy loss by preheating fuel gas. Since load of the high-pressure turbine shifts toward low-pressure one by the inter-cooler, some considerations are necessary for low-pressure side cooling together with reheating cycle. Because of unnecessary steam turbine, the construction cost per kW can be reduced by 20%. 41 refs., 64 figs., 27 tabs.

  10. Experimental study on the response of very large floating structures (VLFS) in wave; Choogata futaishiki kaiyo kozobutsu no harochu oto ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ota, M.; Ikegami, H.; Yamaguchi, Y. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan)

    1997-10-01

    The elastic response of VLFS of 1200m long in wave was studied experimentally using a water tank and integral elastic model of 1/80 scale. As offshore airport, a ultra- thin box type floating structure of 5km long, 1km wide and several meter thick is used, and the effect of elasticity is not negligible for such a structure. The experiment used a water tank of 160m long, 30m wide and 3.1m deep. Supposing a water depth of 20m for real VLFSs, the experiment was carried out mainly in a local shallow water area prepared with a temporary bottom together with that in a deep water area. A simple mooring equipment with a linear spring equivalent to real VLFSs was used. The integral floating model was prepared by not mechanical but welded junction to obtain uniform elasticity. The response in wave showed a complicated 3-D behavior, offering useful data for verification of a behavior estimation method. The response was nearly equal between shallow and deep water areas at the same wave length, and the response amplitude in regular waves was equivalent to the significant amplitude in long and short crested irregular waves. 7 refs., 8 figs., 3 tabs.

  11. Required grades of hull steel plates in consideration of fracture toughness; Hakai jinsei wo koryoshita sentaiyo koban shiyo kubun ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, H.; Yamamoto, M.; Ogaki, Y. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    This paper discusses the required grades of hull steel plates based on the steel ship rule of Nippon Kaiji Kyokai (NK). The minimum value of the allowable crack length in NK rule (critical safety crack length at 0degC just before brittle unstable crack causing fatal fracture) was estimated. In the case where the estimated crack tip exists in a matrix, the crack length was a minimum of 200-210mm, while nearly 60mm in a fusion line at high-heat-input welded joint. The allowable crack lengths estimated from a specified value in the NK rule were fairly different. The allowable crack length at 0degC was also estimated from the minimum value in V-notch Charpy impact test. The private proposal on the required grades of hull steel plates in consideration of fracture toughness was discussed. Thirty-five percent of crack lengths found in real ships is 100mm or less, however, cracks of 250-400mm long are frequently found suggesting the allowable crack length of 400mm. The required grade integrally considering required values and design conditions is demanded to secure the reliability of hull strength. 5 refs., 5 figs., 2 tabs.

  12. FY 1996 annual report of investigation on biological fixation of carbon dioxide. 2; 1996 nendo seibutsuteki CO2 kotei ni kansuru chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Various kinds of biological fixation processes of CO2 were evaluated from the various viewpoints. Afforestation of tropical and temperate areas, greening of desert, biomass energy production in these areas by energy plantation, coastal mangrove plantation, fertilization with nitrogen and phosphate to outer ocean and coastal, upwelling zone fertilization with iron, and coral reef expansion combined with OTEC (ocean thermal energy conversion) were comparatively investigated as the selected measures. As a result, the cost of CO2 fixation by cultivation of sea weed and plankton was much higher than that of afforestation. The iron fertilization method which was considered to be one of the high CO2 reduction potentials might be economical. However, its effect could not be quantitatively evaluated. The afforestation of tropical and temperate areas seemed to be most feasible in a short term from the viewpoints of economy and environment. It was suggested that the establishment of a systematic water management technology could make greening and afforestation of desert. 76 refs., 27 figs., 28 tabs.

  13. Research cooperation project on conservation and sustainable use of tropical bioresources; Seibutsu tayosei hozen to jizokuteki riyonado ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Research cooperation has been conducted on the conservation of biological species inhabiting in the tropical rainforest in developing countries in tropic zone and the sustainable use of genetic resources using biotechnologies. For the research cooperation with Thailand in FY 1996, research of the food acquisition strategy of the Primates has been conducted. A total of 19 species of animals and plants, i.e., 7 species of arbors, 7 species of herbs, and 5 species of insects, were newly confirmed for pig-tailed monkey. In Indonesia, a feasibility study was conducted on the information center of Indonesian tropical bioresources. For the research of culture collection of bacteria, 113 strains of acetic acid bacteria and 85 strains of lactic acid bacteria were separated from Indonesian specimens, and they were identified. An agreement was concluded with Malaysia, and discussions were conducted for the concrete implementation plan. For the project, construction of a database was investigated for bioresources including bacteria and higher animals useful for industries. Maintenance of gene bank was also investigated. 391 refs., 61 figs., 93 tabs.

  14. FY 1998 annual report on the surveys on high-efficiency power generation techniques of the next generation; 1998 nendo jisedai kokoritsu hatsuden gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Comprehensive surveys on and assessment of seeds of the high-efficiency power generation techniques of the next generation, both domestic and overseas, are conducted to help propose preliminary national research themes. In FY 1998, the survey efforts are directed not only to the trends of those for industrial power generation under development, e.g., combined cycle, coal-gasification combined cycle and pressurized fluidized bed combined cycle, but also to the trends of newly proposed systems, e.g., humid air combined cycle, methane reforming combined cycle, fuel reforming/humid air combined cycle, fuel reforming/fuel cell combined cycle and micro gas turbine, to further enhance efficiency by integration with a gas turbine power generation system. The efforts are also directed to (new power generation techniques in the basic research stage) being studied mainly by academic and research organizations, and to development trends of new power generation techniques under development by private enterprises, mainly based on the patent survey. (NEDO)

  15. International symposium on environmental impacts of advanced alternative to CFC; CFC shinki daitai busshitsu no kankyo eikyo ni kansuru kokusai symposium hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-07

    The international symposium on environmental effects of new CFC substitutes was held in Tsukuba City, Ibaraki Pref. on February 7-9, 1996, and 19 papers were made public. In Session 1 (Plenary lecture), reports were made on Global warming and climate change: a review of recent studies; Stratospheric ozone, CFCs, and CFC-substitutes: an update, etc. In Session 2, Measurements of OH rate constants for advanced refrigerants as well as HCFCs and HFCs; The reaction rate of CFC alternatives with OH radical; Experimental and estimated rate constants: reactions of hydroxyl radicals with several halocarbons, etc. In Session 3, Measurement of uptake coefficients of some acetyl halides and fluorinated ethers into water; Mass transfer at the air/water interface: removal processes of halocarbonyl compounds; Heterogeneous reactions of fluorinated ethers on allophane or titanium dioxide, etc. In Session 4, papers were reported on model calculations relating to the global warming.

  16. Study on the detached house plan using of a maximum natural energy. Part 1; Shizen energy fukugo riyo no keikaku ni kansuru kenkyu. 1

    Energy Technology Data Exchange (ETDEWEB)

    Wada, I.; Mino, M.; Miyata, T.; Okawa, M. [Nihon University, Tokyo (Japan)

    1996-10-27

    The geographical position or environment is set on the assumption that the natural energy of a detached house is used in a hybrid state. Moreover, the energy consumption of the house and the natural energy supply obtained from the geographical position were compared and investigated. As a result, the energy consumption is 10,617 kWh, and the energy supply is 8,236 kWh. About 78% of the whole consumption can be theoretically made from natural energy. The energy supply is calculated on the low side during prediction. Therefore, an increase in the energy supply is expected by installing a solar collector based on solar energy, expanding the solar panel area, and increasing the number of wind mills. However, this energy is partially lost via an inverter while it is supplied to the general domestic equipment. At the six main points in Tokyo and its districts, the adaptability of natural energy used based on the regional characteristics is investigated presently and the installation of a system is examined. 13 refs., 2 figs., 6 tabs.

  17. Application of photovoltaic generating system to electric power in large ship; Taiyoko hatsuden system no ogata senpaku eno oyo ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Katagi, T.; Ogawa, S.; Nishikawa, E.; Hashimoto, T. [Kobe University of Mercantile Marine, Kobe (Japan); Ishida, K.

    1996-10-27

    This paper describes the design of electric power system in a ship with photovoltaic power generating system, to examine applicability of the photovoltaic power generating system to the inboard power source. It also discusses effectiveness of the system for sea environment. At first, the actual route of a car carrier, meteorological data, and quantity of power consumption were picked up from the deck logbook and engine logbook. Then, the installation area of photovoltaic arrays, the quantity of photovoltaic power generation derived from the quantity of solar radiation, and the capacities of batteries and inverters were calculated, to design the electric power system in the ship with photovoltaic power generation system. Moreover, the NOx and SOx emissions were compared between the present power system and the usual power system using diesel power generator, to discuss the effectiveness of the present system for sea environment. Consequently, it was found that the emission of NOx was reduced by about 33% and the emission of SOx was reduced by about 28% compared to the usual power system. The effectiveness for sea environment was confirmed. 9 refs., 5 figs., 4 tabs.

  18. Features of vertical axis wind turbine and development of airfoils sections; Chokusen yokugata suichoku jiku fusha no tokucho to yokugata ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Seki, K.; Shimizu, Y.; Yasui, T. [Tokai University, Tokyo (Japan); Nakayama, H. [Oriental Kiden Company, Osaka (Japan)

    1996-10-27

    Features of a straight wing type vertical axis wind turbine (VAW) and its airfoil sections were studied. The wind turbine in which various aerodynamic work components are mounted on the rotation axis normal to the ground surface is named VAW. Like the airfoil section of aircraft, in lift type VAW, wind turbines were driven by lift 70-90 times as large as drag in some cases. Features of the VAW airfoil section which is a straight wing in plan and a fixed pitch wing (with a fixed angle to a blade support arm) in cross section, and those of wind turbines were studied. Some factors affecting the features, work principle and performance of VAW were clarified. On airfoil sections, products of each weight function and each corresponding aerodynamic factor (lift, drag and pitching moment factors) were plotted on an attack angle ({alpha}) axis. From the conditions for increasing the total sum of areas drawn by the products on the {alpha} axis, various characteristics required for airfoil sections were clarified. Such characteristics nearly agreed between an airfoil section for favorable starting characteristics and that for high efficiency. 3 refs., 7 figs.

  19. Performance analysis on utilization of sky radiation cooling energy for space cooling. Part 2; Hosha reikyaku riyo reibo system ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Marushima, S.; Saito, T. [Tohoku University, Sendai (Japan)

    1996-10-27

    Studies have been made about a heat accumulation tank type cooling system making use of radiation cooling that is a kind of natural energy. The daily operating cycle of the cooling system is described below. A heat pump air conditioner performs cooling during the daytime and the exhaust heat is stored in a latent heat accumulation tank; the heat is then used for the bath and tapwater in the evening; at night radiation cooling is utilized to remove the heat remnant in the tank for the solidification of the phase change material (PCM); the solidified PCM serves as the cold heat source for the heat pump air conditioner to perform cooling. The new system decelerates urban area warming because it emits the cooler-generated waste heat not into the atmosphere but into space taking advantage of radiation cooling. Again, the cooler-generated waste heat may be utilized for energy saving and power levelling. For the examination of nighttime radiation cooling characteristics, CaCl2-5H2O and Na2HPO4-12H2O were tested as the PCM. Water was used as the heating medium. In the case of a PCM high in latent heat capacity, some work has to be done for insuring sufficient heat exchange for it by, for instance, rendering the flow rate low. The coefficient of performance of the system discussed here is three times higher than that of the air-cooled type heat pump system. 8 refs., 5 figs., 4 tabs.

  20. Study on the living environment of semi-underground room with attached green house; Fusetsu onshitsu no aru hanchikashitsu no kyojusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, T.; Tsukayama, N. [Ochanomizu University, Tokyo (Japan)

    1996-10-27

    In response to demand for the expansion of living space, the living environment of semi-underground room has been investigated. An attached green house (passive solar house) is adjacent to the semi-underground room. This is reinforced concrete construction, having flat type solar collector on its roof and lighting window in its north side. It does not have artificial air conditioners. Based on the measurements of daylight factor, artificial lighting is not required at the window in the daytime, but it is desirable to use daylight and artificial lighting together at the center. The performance of sound insulation depends on the high performance soundproof sash level. There is less daily temperature variation due to its large heat capacity, and less yearly temperature variation than the outside. By shielding the solar radiation, the insolation in the green house in summer can be restricted in the same as in winter. The insolation can be easily received in winter due to its large vertical intensity of solar radiation. The green house in the south side is useful for improving the living environment of semi-underground room. The temperature rise in the semi-underground room can be restricted by opening window in summer. It is desirable for the comfortable living to use artificial cooling to reduce the daytime temperature by 3 to 4{degree}C. In winter, it is comfortable to heat by 4 to 5{degree}C. 2 refs., 7 figs.

  1. Study of dynamic creep of SBR/NR blended rubber. SBR/NR blend kei gomu no doteki creep gensho ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, K.; Takane, K. (Shibaura Institute of Technoloyg, Tokyo (Japan)); Mifune, N. (Railway Technical research Institute, Tokyo (Japan))

    1991-10-25

    Dynamic creeping phenomena aere investigated using natural rubber NR, solution-polymerized SBR, and a single system rubber filled with carbon black in the modified SBR{sup {asterisk}} added with functional froups into the end of its rubber molecules, and their blended rubbres of SBR/NR and SBR{sup {asterisk}}/NR. The following conclusions were obtained: The amount of dynamic creep is expressed as the sum of the creep {epsilon}{sub 1} induced by broken physical bonding due to interactions between polymer chains, the creep {epsilon}{sub 2} induced by the transformation of filled particle structure into a stable structure, and the creep {epsilon}{sub 3} induced by phase separation of a blended structure. The SBR{sup {asterisk}} blended system has small amount of physical bond, and the filled particles form a stably oriented structure, without an NR phase separation phenomenon observed during the creep process. Thus, this system was found to have much smaller dynamic creep than the SBR blended system. 4 refs., 16 fugs., 4 tabs.

  2. Study on three-dimentionally stressed fatigue of NB/SBR blended rubber. NR/SBR blend gomu no sanzigen oryoku hiro ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, K.; Imura, Y. (Shibaura Inst. of Technology Tokyo (Japan). Faculty of Engineering)

    1992-01-15

    The purpose of this study is to investigate fatigue processes, fatigue life times and fatigue fracture patterns by three-dimentional stresses on carbon black filled blended rubbers of solution-polymerized SBR and SBR{sup *} modified at the end of SBR polymer chains by functional groups with NR. In the experiment, specimens consisting of 7 kinds of NR/SBR{sup *} blended rubber and 3 kinds of NR/SBR blended rubber were put to the three-dimentional stresses test. The average value of physical properties as well as characteristic values of anisotropy and fatigue fractures were measured. As a result, the following conclusions have been derived: In rubber phases of NR and SBR,or SBR{sup *}, compatible structures were formed by polymer chains of NR and SBR(SBR{sup *}) at their boundaries and they became obstacles to the propagations of micro-cracks generated by fatigue. Fracture patterns were controlled by velocities of a formation process of anisotropic layer structures and a generation process of surface cracks. Fractures grew in lateral direction in NR system,because the formation of anisotropic layer structures was faster. Fractures grew in radial direction in blended rubber systems,because the formation of surface cracks was faster. 6 refs., 26 figs., 2 tabs.

  3. Integrated interpretation of AE clusters and fracture system in Hijiori HDR artificial reservoir; Hijiori koon gantai jinko choryuso no AE cluster to kiretsu system ni kansuru togoteki kaishaku

    Energy Technology Data Exchange (ETDEWEB)

    Tezuka, K. [Japan Petroleum Exploration Corp., Tokyo (Japan); Niitsuma, H. [Tohoku University, Sendai (Japan)

    1997-05-27

    With regard to a fracture system in the Hijiori hot dry rock artificial reservoir, an attempt was made on an interpretation which integrates different data. Major factors that characterize development and performance of an artificial reservoir are composed of a fracture system in rocks, which acts as circulating water paths, a heat exchange face and a reservoir space. The system relates not only with crack density distribution, but also with cracks activated by water pressure fracturing, cracks generating acoustic emission (AE), and cracks working as major flow paths, all of which are characterized by having respective behaviors and roles. Characteristics are shown on AE cluster distribution, crack distribution, production zone and estimated stress fields. Mutual relationship among these elements was discussed based on the Coulomb`s theory. The most important paths are characterized by distribution of slippery cracks. Directions and appearance frequencies of the slippery cracks affect strongly directionality of the paths, which are governed by distribution of the cracks (weak face) and stress field. Among the slippery cracks, cracks that generate AE are cracks that release large energy when a slip occurs. Evaluation on slippery crack distribution is important. 7 refs., 8 figs.

  4. Evaluation report on research and development of a subsea petroleum production system; Kaitei sekiyu seisan system no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-01

    In order to assure stable supply of oil and natural gas resources, and achieve enhancement in ocean development technologies in general, development has been made on the subsea petroleum production system (SBPPS), which is effective in ocean floor petroleum production from oil fields at great depths (300 m or deeper), and can be applicable to continental shelves and continental slopes around Japan. The SBPPS consists of four sub-systems of shafts, pipelines, manifolds, and riser and oil storage, whose basic development targets were established for the total system. The system was given a conceptual design for the total system, and the above four sub-systems were designed according to the conceptual design. The experimenting devices of each system were fabricated on a trial basis while fundamental studies are being made on component technologies, and experiments were performed to verify basic functions of the sub-systems. Developments were made on such operation technologies as the system operation technology, production control technology, safety control technology, and maintenance and repair technology required to operate the SBPPS. On-shore and general off-shore experiments were carried out to verify the functions of the experimenting devices of each system, the comprehensive functions and the operation technology. Comprehensive evaluation was given on the above achievements from the technical, economic and social viewpoints. (NEDO)

  5. Application of two-phase mixture model to the unsaturated vertical flow through snow; Niso kongotai model no sekisetsunai fuhowa enchoku shinto eno tekiyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yatomi, C.; Ishida, H. [Kanazawa University, Ishikawa (Japan). Faculty of Engineering; Hata, T. [Ishikawa College of Technology, Ishikawa (Japan)

    1995-02-15

    The unsaturated vertical flow through snow was analyzed with a model prepared to rationally express the progression of moisture movement through porous media. For the model, the moisture existing in the two-phase mixture was assumed to be composed of free phase and trapping phase. It was then presumed that the aqueous behavior complied with the conservation law of moisture in both phases and Darcy law expanded to the aqueous transfer in the free phase. The thus derived basic equation was analytically solved by linear approximation. The result of calculation was applied to the experimental result on the granulated snow samples which had considerably progressed in metamorphosis. As a result of application, it was known that the present model correctly reproduces the run-off from the snow sample, when it is more or less abundant after its rising. Pertaining to the parameters to structure the model, it was indicated that K, {alpha} and {beta} express the starting time of run-off, damping part of run-off, and trapping mechanism and flow characteristics, respectively. 8 refs., 5 figs., 2 tabs.

  6. Survey of implementation plan constructed for `the New Earth 21 Project`; Chikyu saisei keikaku no jisshi keikaku sakusei ni kansuru chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    It is necessary to establish scenarios for reducing CO2 emissions and for developing CO2 emission control technologies to obtain a global consensus, using appropriate analytical models. For modification of the DNE-21 (Dynamic New Earth 21) model, it has a category designated as innovative technologies not involving CO2 emission and an optional consideration for the absorption of atmospheric CO2 by biomass. A global carbon circulation model, including vegetation in its scope, is also incorporated. Major results of the simulation are shown. When 20% reduction in CO2 emissions is required for only OECD countries after the year 2020, it has been demonstrated that CO2 concentration in the atmosphere will reach as high as about 900 ppm in 2100 due to CO2 emission by developing countries, and will not be a tolerable level. Under the condition that CO2 concentration in the atmosphere is controlled at 450 ppm in 2100, the amount of renewable source of energy from photovoltaic power generation and biomass will increase and technologies of CO2 recovery and storage will decrease. Research and development of the production of methanol from recovered CO2 will be adopted as innovative technology for CO2 measures. 69 refs., 112 figs., 79 tabs.

  7. Study on the effect of micro-gravity on bio-functions; Seitai kino eno bisho juryoku no eikyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The effect of micro-gravity on bio-functions and vital reaction was studied using the facility of Underground Gravity-free Experiment Center Co. On the effect on osteoblast shape and gene expression, although fluorochrome reacting with Ca was well taken into cells, no significant difference in Ca content in cells was observed before/after falling. Expression of genes related to cell propagation was controlled under micro-gravity. Protoplast fusion of Lentinus was unaffected by micro-gravity. The mRNA fragments of gravity sensitive mutant of rice plant were affected by micro-gravity. Paramecium was set swimming in solutions with different specific gravities. The reaction behavior of Paramecium was affected by the difference in specific gravity between cell bodies and solutions. The water content metabolism functions of a mouse with needle stimulus, in particular excretory, were slightly promoted by micro- gravity. The cortisol level in blood of a falling mouse group rose showing strong stress. As the preliminary study on the geotaxis of insects, motion of bagworm was observed. 12 refs., 38 figs., 4 tabs.

  8. Research report of fiscal 1997. Basic research on the commercialization of innovative energy technologies; 1997 nendo chosa hokokusho. Kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper summarizes the research result in fiscal 1997 from the basic research results on the commercialization of innovative energy technologies. The target of a photovoltaic power generation market includes isolated power sources (several kWp) for distant places or developing countries, and those (several tens kWp) for personal residences or public facilities. Although the former is mainly promoted in the West, while the latter over the world, their profitability is unsolved. Power plants over several hundreds kWp are in demonstration test. Solar heat power generation of several tens to hundreds MWp is most profitable, however, small-scale one is poor in feasibility. Australia takes an interest in distributed photovoltaic power generation directly connected with actual lives of residents, and has a dominant opinion that desert is useless as large-scale site. This country lays emphasis on protection and maintenance rather than positive use of desert based on a basic cognition that desert is easily changed and broken. The Australian government announced power company`s obligation to use renewable energy by 2%, and a strong organization is scheduled to be newly established. 59 figs., 57 tabs.

  9. Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, R.; Tsuru, T. [Tech. Research Center, Japan National Oil Corp., Tokyo (Japan); Matsuoka, T. [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-05-01

    The Physical Modeling System introduced into the Technology Research Center, Japan National Oil Corporation, and data collected by use of the system are presented. The Physical Modeling System is 10,000 times smaller than the real one, comprising a water tub section, measuring device section, and control section, etc. The water tub section comprises a tub for housing the model, transducers for transmitting and receiving vibration, controllers, etc. The water tub measures 1.8{times}1.2{times}0.9m. The model used in the experiment is an `inclined multilayer model` with each of its six layers pinching out toward the top, and is usable for the comparison of various migration methods. In one case in the records, reception was made at 184 reception points deployed at intervals of 3mm, when the minimum offset was 15mm and the maximum offset 564mm. Nothing very obvious was observed when the ordinary overlapping of DMO and CDP was applied to this record, which suggests that pre-overlapping migration treatment is required. 5 figs.

  10. Study on search for antioxidant peptides in unused protein resources and their production; Miriyo tanpaku shigen kara no kosanka pepuchido no tansaku to seisan ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the development of antioxidants that are high in use value, peptides are produced in a bioreactor from so-far-unused or little-used protein resources originating in marine organisms collected along the Sanriku coast, and antioxidants that they may contain are searched for. Three kinds of red alga, eight kinds of brown alga, and internal organs of processed fish are treated in the bioreactor. The bioreactor is a rotary membrane type especially built for the effective decomposition of proteins in this study. Reaction solutions containing proteins and enzymes are let through an ultrafiltration membrane module in rotation at a high speed, and the products with their molecules reduced in weight are effectively taken out of the system (free of clogging). The specimens checked for antioxidant features are all found to be positive when subjected to the iron rhodanide method or carotene method, the two methods determining the change in the amount of oxygen in hydroperoxide and {beta}-carotene that are produced when the linolic acid is oxidized. Every one of the specimens prepared for this study exhibits antioxidant features in plural, different mechanisms. It is necessary to collect further basic findings about oxidation inhibiting mechanisms for the development of more active antioxidant peptides. 39 refs., 46 figs., 8 tabs.

  11. Basic research on the development of 'intelligent-type' humidity control materials; Intelligent gata choshitsu zairyo no kaihatsu ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tomura, S.; Maeda, M.; Inukai, K.; Ohashi, F.; Suzuki, M.; Suzuki, K.; Shibasaki, Y. [National Industrial Research Institute of Nagoya,Nagoya (Japan)

    2000-10-25

    The water vapor adsorption desorption isotherms of purified and/or synthesized sepiolite, allophane, diatomite, selectively leached kaolin and mesoporous silica were measured to develop humidity control materials in living environments. Based on Kelvin's capillary condensation theory, suitable pore diameters for controlling relative humidity at 40 and 70% were calculated to be 3.2 and 7.4 nm, respectively. Wakkanai diatomite, purified allophane, selectively leached kaolin and mesoporous silica have suitable pore diameters and high water adsorptivity, and were considered as candidates for humidity self-control materials. Among these materials, mesoporous silica formed as a tile showed the best performance as a humidity control material in desiccator and model house levels. (author)

  12. Study of seismic data acquisition using physical modeling system; Butsuri model jikken sochi wo mochiita data shutoku gijutsu ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Tsukui, R.; Tsuru, T. [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

    1996-10-01

    For the physical modeling system of Technology Research Center, Japan National Oil Corporation, data acquisition on the ocean and ground can be simulated using models. This system can provide data for verification of the data processing and elastic wave simulation algorithm. This can also provide data for decision of experiment specifications by making a model simulating the underground structure of the given test field. The model used for the physical modeling system is a gradient multilayer model with six-layer structure. Depth migration before stacking was conducted using data obtained through two acquisition methods, i.e., up-dip acquisition and down-dip acquisition. The depth migration before stacking was performed for data obtained by up-dip acquisition in addition to the records obtained by down-dip acquisition. Consequently, a definite reflection surface was observed, which has not been observed from the processing results of down-dip acquisition data. 9 figs.

  13. Control system for platooning. Comparison between sliding control and PID control; Jidosha unten seigyo system ni kansuru kenkyu. Sliding to PID control

    Energy Technology Data Exchange (ETDEWEB)

    Fujioka, T.; Banba, J. [The University of Tokyo, Tokyo (Japan)

    1995-04-20

    The difference in result of control by the control system was studied by designing the vehicle follow-up control for the platooning of automobile. A comparison was made between the sliding control based on the non-linear control theory, and PID control which is judged to be the most primitive. A two-wheel model of four-wheel vehicle was used as a vehicle model, while the automobile model was composed of non-linear factors, which were an engine, torque converter, gear shift map and tires. When the initial figure of both distance between and speed of vehicles is close to their target figure (less than {plus_minus}8m and {plus_minus}5km/h, respectively), a good result of control can be given by both the sliding control and PID control, so that the former control was known to be as very effective as the latter control. When the initial figure of both distance between cars and speed of vehicles is less close to their target figure (less than {plus_minus}20m and {plus_minus}5km/h, respectively), the sliding control is higher in convergency than the PID control. It was thus known that the former control gives an effective result of control even if the inititial value is far. 6 refs., 16 figs., 1 tab.

  14. Research and development cooperation project on environmental measurement using laser radar (environmental network) in fiscal 1993; Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the purpose of contributing to the research cooperation project on the development of a laser radar for environmental measurement, the paper surveyed the present and future trend of the environment related information network in Indonesia. The survey was conducted in terms of a name of the network, the main administration body, the number of users, the utilization status, the use protocol, details of service, domestic mode installation sites and the main administration body, accounting system, types of the network used, reliability and stability of network, limitations on the use and details of the limitation, etc. The plan for expanding telecommunication equipment is being advanced in a very quick tempo. However, there are many problems in digitalization, and it is feared that the plan will be delayed. As to telecommunication quality and connection quality, the telecommunication completion rate, SCR, is very low, approximately 24% on average, which is equal to that around 1990 in Japan. The business service for users is all bureaucratic since they have a lot of applications for the installation piling up with no exception to the rule of developing countries. 23 figs., 10 tabs.

  15. Report of 'Survey on Asian environmental information networks'; 'Asia kankyo joho network chosa' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is implemented to survey the current statuses and future trends of the Asian district environment-related information networks, for the (research cooperation project for development of environmental condition measuring laser radar systems), being promoted by NEDO. First, current statuses of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, major domestic nodes and internationally connected conditions are surveyed mainly for internet-connected networks, for surveying the current statuses and future trends of the research networks in Asian countries. Second, current statuses in Indonesia of the network names, managing organizations, user numbers, conditions of use, protocols for use, service conditions, domestic node sites and managing organizations, charge systems and institutions, types/reliability/ stability of the circuits, and conditions of restriction of use, if any, for surveying the current statuses and future trends in Indonesia. Third, conditions of and needs for network utilization by researchers for Asian district environments. (NEDO)

  16. Fiscal 1999 survey report. Survey and research concerning development of next-generation chemical process technologies; 1999 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To further enhance resource/energy conservation and environmental impact reduction, it is necessary to develop innovative chemical reaction process technologies. It is for this reason that 'development of next-generation chemical reaction process technologies' is being carried out under the New Sunshine Program. The survey and research, for the fulfilment of the above goal, aim to select important technologies and put in a easy-to-study order the problems contained in associated technologies for picking out tasks for future studies for the purpose of suggesting some subjects to be taken up for future development. In addition, studies are made about how a comprehensive technology assessment system should be. In this fiscal year, propositions are compiled for research and development projects on five subjects. Studies of subjects other than these five will also continue to eventually build concrete propositions on them. The said five subjects involve 1) the development and application of nonaqueous biotechnologies, 2) biotechnology-aided polymeric material creation processes, 3) construction of high-efficiency energy conservation processes using innovative grain handling technologies in the high-temperature reaction field, 4) manufacture of high-performance polymeric materials for batteries and development of battery fabrication processes, and 5) the development of an energy conservation process maximally utilizing environmentally-friendly polyolefin. (NEDO)

  17. Research and development cooperation project on environmental measurement using laser radar in fiscal 1995 (environmental network); Kankyo keisokuyo laser radar no kaihatsu ni kansuru kenkyu kyoryoku (kankyo network)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the cooperative work with Indonesia of R and D of a laser radar for environmental measurement, the paper described the development of an environmental network. The field survey was conducted in April, July and December 1995 and in March 1996. For the investigational research, five meetings of the committee and four times of group work were held. The Asian environmental network was studied in terms of its arrangement, operation and management, and the overall network/path control design were being prepared. To make the persons concerned abroad and in Japan understood the APEC Osaka Conference held in November 1995, a homepage APEC `95 Kansai was opened using WWW (World Wide Web, a decentralized hyper media system which can dispatch information to the whole world by network using hyper text). Moreover, in connection with this, a homepage was opened of CICC (Center of the International Cooperation for Computerization, a center controlling the whole Asian environmental information network system where E-mail and data are exchangeable with Indonesia via Tokyo NOC (Network Operation Center)). 49 figs., 8 tabs.

  18. Trend of research on future development of new biocatalysts. 2; Shinki bio shokubai no sosei ni kansuru kenkyu doko chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Creation of new biocatalysts was surveyed to convert chemical reactions into environment-friendly processes. Biocatalysts are characterized by their high catalytic activity, uniqueness of reactions, and non-pollution under mild conditions. Stability is required for them, such as heat resistance, solvent resistance, acid resistance and alkali resistance, under severe conditions. For the development of new biocatalysts, it is necessary to multiply utilize the techniques containing enzymes, ribozymes, mold synthetic polymers, chemical modification, and non-natural proteins. Natural enzymes have been conventionally improved through the search, imitation and modification. Hereafter, new biocatalysts with functions required for the reactions should be created by integrating information regarding functions, structures and activation of these enzymes. It is indispensable to cooperate closely with supporting techniques, such as gene engineering, organic synthesis, biophysics and computer chemistry. 35 refs., 26 figs., 1 tab.

  19. Study on buckling and ultimate strength of a rectangular plate under combined inplane load; Kumiawase mennai kaju wo ukeru kukeiban no zakutsu saishu kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Fujikubo, M.; Yao, T.; Varghese, B. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1996-10-01

    Elasto-plasticity analysis by using the finite element method was performed on a case that bi-axial compression and shear act on a thick rectangular plate, and applicability of the plasticity correction method was discussed. In the discussion, an investigation was made on effect of the loading method of a load on correlation between initial yield strength and ultimate strength of a rectangular plate under bi-axial compression. The analytical result from the finite element method was compared with estimated values derived by using the plasticity correction method with regard to the buckling strength. The result obtained may be summarized as follows: the effect of the loading method for combined load on the correlation between the initial yield strength and the ultimate strength is small; an approximation expression was derived for the upper limit of maximum initial bend of a deck panel of an actual vessel; the plasticity correction method for buckling strength as specified by classification societies has a certain applicability as a method to estimate ultimate strength on the safety side against plate thickness in a range of the upper limit of initial bend of an actual vessel; however, this method may estimate strength higher than the actual value depending on load ratio, hence attention is required. 5 refs., 8 figs.

  20. Study on mechanical behavior of the deep embeded steel sheet pile cellular bulkhead. Neire no fukai hagane yaita cell shiki gogan no rikigaku teki kyodo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Higashigawa, T.; Achiwa, F. (The Chubu Electric Power Co. Inc., Nagoya (Japan)); Matsuo, M. (Nagoya Univ., Nagoya (Japan). Faculty of Engineering); Sunami, S. (Nikken Sekkei, Osaka (Japan))

    1991-09-20

    At the Hekinan coal-burning thermal power station of Chubu Electric Power Company, there is a plan to construct its ash dump by closing the neighboring sea area with bulkheads. This bulkhead is deeply embeded steel sheet piles to be struck into a soft clay layer. Since it is necessary to improve the ground in a wide area for stabilization of soft clay, the specifications as well as the scope of improvement of the basic design plan were noticed, a qualitative study of the bulkhead was done by a numerical analysis aiming at realization of a rational and economical bulkhead and an execution plan which modified the above was prepared. In this execution plan, the reduction as much as about 9% became possible for the construction cost of about 1km long bulkheads. In order to demonstrate the adequacy of this execution plan, loading tests were conducted on full-size cellular bulkheads corresponding to the basic plan as well as the execution plan. As a result, the tested values agreed very well with the analytical results and upon comparison between them, the displacement at the tip of the cellular bulkhead and other measured values showed no meaningful difference, thereby it was confirmed that the execution plan had the same level of stability as the basic plan. 5 refs., 26 figs., 5 tabs.

  1. Fiscal 1998 research report. Survey on the international standardization of top technologies; 1998 nendo chosa hokokusho. Sentan gijutsu no kokusai hyojunka ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made on the trend of the international standardization of top technologies in developed countries. With a recent progress of technology business beyond boundaries, the interrelation between technology and industry is becoming complex increasingly. For construction of industrial technology policies, the factor analysis of the international standardization of top technologies is important. Recently, public standardization (promoted by public organizations) and de- facto standardization (formed in market competition) have been promoted in a top technology field. International comparison was made on the basis of the report on international comparison of technical competitive powers by the US government or non-profit organizations. Survey was made on the trend of international unification of standards and positioning of standards in enterprise strategy, and approaches of ISO, IEC, ITU and developed countries to standards. Case study was made on digital mobile telephone, IC card, OS for PCs, electric vehicle and fine ceramics. (NEDO)

  2. Basic investigation on deflection wave propagation and strength of very large floating structures; Choogata futai kozo no tawami hado denpa kyodo to kyodo ni kansuru kisoteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    The response strength in which deflection waves propagating in the elastic body of a large floating structure with an order of km in length and width was investigated. Attention was paid to the waves propagating the place fully away from the boundary of a very large floating body so as to obtain the dispersion relation of waves and the relation between incident waves and deflection waves. Next, the frequency response was checked from the aspect of the displacement amplitude and strength for beams and plates. The dispersion relation of waves propagating the place fully away from the boundary of a very large floating body and the relation between the waves and infinite-point incident waves were represented by an expression. Similarly, the waves propagates more than the infinite-point incident waves in frequency, wavelength, and speed. A lower-limit value exists in the propagation speed. The displacement and stress amplitudes are represented by a relational expression. For plates, the displacement amplitude increases when the wave direction coincides with the small-rigidity direction. The stress amplitude is maximized when the waves corresponding to the ``wave below a floating body = size of a characteristic wave number`` reach the large-rigidity direction. 10 refs., 10 figs., 2 tabs.

  3. Survey report on an environmental harmony type production system of chemical products; Kankyo chowagata kagaku seihin seizo system ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As part of establishing an environmental harmony type production system of chemical products, study and survey were made on PET bottles. Using the life cycle analysis method (LCA), a study was made for proposing a material recycle (MR) method which is environmentally and economically excellent in the stage of recycling waste PET bottles. The total cost of recycling can be reduced by 34% supported by a decrease in equipment cost and improvement in yield if there is no mixture of foreign substances such as aluminum caps and PVC bottles. However, the ratio of the amount obtained from the reduction to the total production cost is small, and it is necessary to take measures from a viewpoint of the cost in a total production process and environmental loads. In a survey in Kawaguchi city, PET bottles discharged from the business sector occupied 41% of all the discharge amount. In a survey in Yokohama city, very important data were obtained on PET bottles appointed as the second type under the recycle law. The quality of PET bottles to be brought to the recycling plant is important for effectively processing PET bottles in MR method. For achievement of MR which is low in cost and small in environmental load, needed were cooperation by citizens, the shipping management system in autonomous government, and changes in design and material quality to be made by the industrial circle. 8 refs., 64 figs., 68 tabs.

  4. Studies on reducing the thermal loads of solar-pumped solid state lasers; Taiyoko reiki laser no netsufuka teigen ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, K.; Yugami, H.; Naito, H.; Arashi, H. [Tohoku University, Sendai (Japan)

    1997-11-25

    It was intended to reduce the thermal loads of solar-pumped solid state lasers (highly densified solar light is irradiated directly onto a laser medium to cause excitation. No electric power is required for the excitation.). For this purpose, experiments were performed by using a selective permeation film. Solar light includes wavelengths not effective for excitation, which causes heat generation and thermal loads such as lens heating effect and thermal stress compounded refraction, degrading the laser beam quality. The Nd:YAG was used as a laser medium, and a multi-layered film (composed of SiO2 and TiO2) which cuts wavelength below 500 nm as a selective permeation film to cut light having wavelengths not required for excitation. A laser transmitting experiment revealed that the slope efficiency is improved by 27% as compared to not using the film. Beam fluctuation was improved to 45%. Using the selective permeation film has realized more efficient conversion of the solar light into a beam with better quality. The results for calculation of heat lens effect by using temperature distribution simulation showed good agreement with experimental values. Using the selective permeation film can suppress the maximum temperature of a laser rod to 68%, as well as the thermal stress. 9 figs., 2 tabs.

  5. Fiscal 1993 study of engineering for making areas prosperous using natural energy; 1993 nendo kankyo chowagata green techno system no kokusai kyoryoku model ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper studied the engineering for activating areas using natural energy. A system has started in which electric power companies purchase surplus electric power from the natural energy use power generation such as the wind power and photovoltaic power generation, etc., and a lot of local self-governing bodies in the country plan `projects to promote town` using the system. However, few engineers and makers can plan `a project to promote town,` making effective use of natural energy which is fickle. Therefore, first, the paper arranged the actual status mostly of the cases of `the projects` using natural energy which have been carried out in the country. Next, the trend of the natural energy utilization technology in countries including the U.S. was described. Moreover, assuming model areas in Japan for working out a concept of model projects on the natural energy utilization and town promotion, a concept was proposed making full use of the utilization technology which has now usability. Arrangement is being made for conditions for the full scale spread as seen in the subsidy system for general users. 3 refs., 176 figs., 61 tabs.

  6. Survey of subjects on the geothermal technology development aiming at marked improvement of economical efficiency; Keizaisei no hiyakuteki kojo to mezashita chinetsu gijutsu kaihatsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of reducing the geothermal development cost and increasing the amount of developable resource, the paper reviewed the geothermal developmental technology. Approximately 30 MW as a scale per unit is economical. The development cost is lowered by 2% if the period for development is shortened by two years, by 11% if the utilization rate is increased by 10%, and by 3% if the success rate is increased by 10%. The cost is reduced by 10% if the steam amount per 1 pit is increased to 1.5 times, and by 4% if the reduction amount is increased to 1.5 times. Improvement of survey/exploration/evaluation technology and improvement of power generation/management technology contribute largely to making the above possible. The drilling depth also corresponds with increases in the amount of steam obtained and the cost. The construction cost including the drilling cost is also an important factor, indicating a cost reduction of 15% if the unit price is reduced by 20%. If a 30% reduction of the power generation cost at a 30MW plant can be made, a 10 yen/kWh is realized, which shows that a geothermal power plant can be competitive with a thermal power plant. When thinking of it without subsidies, the geothermal power generation is most economical of all the renewable energy. In the light of the environment, the CO2 issue, etc., the geothermal power generation is much more advantageous than the thermal power generation. 7 refs., 28 figs., 8 tabs.

  7. Evaluation report on research and development of an ultra-advanced processing system. 3; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-08-01

    This paper describes comprehensive evaluation on the following technologies as the ultra-advanced processing system: (1) large output excimer laser, (2) high-density ion beam, (3) an ultra-precision machining device, (4) ultra-advanced processing, (5) measurement and evaluation, and (6) comprehensive test. In the item (1), research and development was performed on such technologies as output increasing, output stabilization and beam formation, having achieved the targets. In the item (2), research and development was performed on such technologies as beam convergence, plasma control, ion transportation, high-frequency quadruple pole acceleration, and large-capacity class ion beam, having achieved the targets. In the item (3), research and development was performed on form creation and ultra-precision machining, having achieved the targets. In the item (4), research and development was performed on formation of high function thin films to apply the laser abrasion process to large area, ion surface modification, wide band area optics, high reflectance optics, ion injection, dynamic mixing, and modification of ultra high-grade metal surface, having achieved the targets. In the item (5), research and development was performed on high-accuracy roughness measurement, shape measurement, optical property evaluation, a wavelength meter, ultra advanced processing standard measurement, and environment correction technology, having achieved the targets. In the item (6), comprehensive demonstration was carried out on the component technologies. (NEDO)

  8. Survey on the construction of realization scenario of large-scale revegetation of arid regions; Daikibo ryokuka no jitsugenka scenario sakusei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In order to fix carbon dioxide as a measure to mitigate global warming, research of large-scale revegetation of arid regions has been conducted toward the ultimate goals of systematizing revegetation technologies centered on securing and using water resources, evaluating the feasibility of arid revegetation by extending the viewpoint to examine even rainfall increase by artificial means, and establishing a strategic program for large-scale revegetation. A trial revegetation feasibility map was made for a selected target region in Western Australia, and rough revegetation steps were formulated. Selection of proper region, introduction of technology, and planning were conducted by grasping environment of the target revegetation region. As a result, it was found that growth of plants is vigorous at the catchment areas due to the surface water transfer along the topography of surface in spite of poor rainfall. Obstruction of plant growth is partly caused by the corrosion of soil and accumulation of salt, but mainly caused by the shortage of water. Based on these data, ranking of proper regions was evaluated. When the technology is introduced in the region with A-rank, several times of water can be collected. 60 refs., 61 figs., 30 tabs.

  9. Research on improvement of indoor air quality and prevention of fungi; Shitsunai kuki kankyo no kaizen to kabi boshi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Tatsuaki [Ochanomizu University, Tokyo (Japan). Faculty of Human Life and Environmental Sciences

    1998-12-16

    An epidemiological survey survey was performed to elucidate the fungal flora of a dwelling house. The measurements were carried out in an apartment in Yokohama from Jul. 1996 to Dec. 1997. Fungi were isolated from 106 sampling points (the surface of the walls, floors, etc.) with sterile stamps. It was proved that Cladsporium, Penicillium, Eurotium, and Yeasts showed characteristic distribution. Especially Cladsporium was not isolated from the spring to the summer, but increased in the autumn. In addition to the survey, experiments on fungal growth temperature (13, 20, 25, 30, 36, 42 degree C) and water activity (A w 0.75{approx}0.97) were carried out. Cladsporium grew well in 13, 20, 25 and 30 degree C, but didn't grow in 36 and 42 degree C. In addition, the growth activity of Cladsporium was down below Aw 0.91. Eurotium was isolated from under Tatami, where it has an unchanging temperature and relative humidity. Yeasts preferred very high humidity. It was concluded that environmental factors such as temperature and relative humidity related to the growth of fungi. (author)

  10. Research report of fiscal 1997. Study on profitability evaluation technique for waste power generation; 1997 nendo chosa hokokusho. Haikibutsu hatsuden ni kansuru keizaisei hyoka shuho no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For diffusion of waste power generation, cost reduction is important. As the profitability evaluation technique for conventional waste power systems, a simple recovery year method, total waste treatment cost method, generation cost method, and evaluation method by accumulated balance sheet are presented along with their principles. For the generation cost method, trial calculation results are presented based on documents reported. From methods for the study in Institute of Applied Energy, some estimation methods of construction cost are presented, and generation cost and profitability evaluation were studied by parametric accumulation method. The profitability was calculated for RDF power systems, and it was clarified that although as a whole this system is more efficient than a simple refuse incineration system, the balance sheet of local governments is dependent on a responsibility range for the facility. In a combined type (super refuse power generation), generally municipalities bear a combustor and boiler, while a prefecture bears generation facilities. Because of large scale generation, the profitability is dependent on a selling price of electricity. 37 refs., 36 figs., 24 tabs.

  11. Report on `Survey of commercialization of intellectual ownership such as patent rights`; `Tokkyoken nado chiteki shoyuken no jitsuyoka ni kansuru chosa` hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A survey was conducted on research results in industrial circles, universities, etc. in the U.S., Europe and Japan, especially the state of how intellectual ownership such as patent rights is handled and the present situation of the commercialization of intellectual ownership, proposing problems and measures to be taken for promotion of practical use of excellent research results in Japan. The most important thing obtained from the survey is that study jointly by industrial circles and universities in the U.S. and Europe is much more advancing than that in Japan and is firmly established not only in industrial circles, universities and national research institutes, but in the whole society, actually producing a lot of favorable results. For Japan to catch up with the U.S. and Europe, needed is not only accumulation of the ideas in the past, but drastic measures to be taken from a new point of view. Concretely, it was proposed that by belonging intellectual properties such as patent rights to universities/research institutes and transferring their disposal rights to them, royalties of licenses are given back to inventors as incentives, and that as a body promoting the transfer to the industrial circle, `management organization` to which private vitality is introduced is established in universities/research institutes in order to promote interconnection between the industrial circle and universities. 15 refs., 35 figs., 36 tabs.

  12. Research report for fiscal 1998. Research into the recycling of plastic wastes into resources; 1998 nendo hai plastic no saishigenka ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The actualities in Japan are investigated of the types and quantities of plastic wastes, collection and recovery systems, and recycling technologies. Plastic wastes exceeded 9-million tons in 1996, of which 39% was effectively utilized while 61% was merely incinerated or used for reclamation. The 61% of the plastic wastes which are equivalent to oil resources in terms of the energy they contain is found dealt with in such ways, for which additional energy has to be consumed. Some problems are mentioned that occur in the CO2 gas reduction effort in the process of plastic waste recycling for each of its stages of production, distribution, assortment, recovery, and reuse. The problems involve the required reform into production designs and systems with the greatest importance attached to recyclability; share of the expenses between the producing and distributing parties and financial support to assortment/recovery systems; reform of consciousness of both people at large and the administrative organizations, mutual collaboration between them, and reasonable share of expenses between them; construction of a unified assortment/recovery system; expansion of the scope of use of recycled products and the building of environments that encourage their use; diversification of recycling methods and establishment of technologies therefor; and limits on the use of materials and products that generate heavy impacts on environments during their life cycles. (NEDO)

  13. FY1998 report on the surveys and studies on developing next generation chemical process technologies; 1998 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For further resource and energy conservation and environmental load reduction, development is necessary on innovative chemical reaction technologies. This paper describes surveys on next generation chemical processes. As non-halogen processes subject to development of new catalysts, new processes were investigated and searching experiments and discussions were given on isocyanate, propylene oxide, and phenol. Technological progress in the C1 chemistry was investigated. Problems in hydrocarbon compound oxidation, hydroxylation, and decomposition by utilizing microorganisms were put into order as application of environmentally friendly technologies. Marine biotechnical possibilities were surveyed. The surveys were given on new processes utilizing the phase transfer catalyst forming a third phase, manufacture of biodegradable plastics, and a novel reaction system combined with self-separation process using molecular assembly. Possibilities were searched on designing a truly simple production system of highly energy saving type. Such fundamental common technologies as structure analysis, property control and reaction engineering were investigated for methods to manufacture functional micro-powder chemical materials. Development was discussed on a system for technology assessment over whole product life cycle to structure a technology assessment basis. (NEDO)

  14. Study on application of flat plate structure to high-rise buildings; Flat plate kozo no koso tatemono eno tekiyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takata, K.; Tsuda, K.; Eto, H. [Obayashi Corp., Tokyo (Japan)

    1999-01-10

    In this study, an improved flat plate structure was developed by an attempt to shift the critical section (the bending yield position) from the column surface towards the span center by increasing the amount of main reinforcement near the column joint. Performance testing of the improved flat plate structure to clarify its basic properties, it showed that its hysteresis characteristics were superior to those of the conventional type (the amount of main reinforcement is uniform in the direction of the axis of member). Based on the experimental results, the appraisal of hysteresis characteristics and the method of section computing were established as the design methods. These newly established design methods were applied to the existing 26-story high-rise building of RC construction, and a simulation was performed to analyze the effectiveness of the improved flat plate structure. The response results satisfied the design criteria for general high-rise buildings, thus confirming the feasibility of constructing high-rise buildings incorporating the flat plate structure. (author)

  15. Fiscal 2000 research report on the study on management program for comprehensive assessment of chemical materials; 2000 nendo kagaku busshitsu sogo hyoka kanri program ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the realization of environmentally friendly, sound economic activities and the assurance of a safe and peaceful daily life for people, studies were conducted about comprehensive risk assessment and management techniques to use in dealing with chemical substances. Concerning the above-named management program, a workshop was called, where panel discussion and exchange of views and opinions were held. In the study of overseas technological trends, visits were paid to interested institutes and corporations in Denmark, Sweden, and Germany, where hearings were held over the management and manufacture of chemical substances. Concerning the control of chemical substances, surveys were conducted of the control in Japan and abroad and of the methods that businesses and other organizations followed in meeting the control. It was found that the control was being dealt with earnestly in every country and that chemical substances would stay managed under international collaborative conditions. Efforts were being positively exerted by businesses and other organizations to properly manage and reduce chemical substances and to develop and use substitutes. It was found that measures for handling chemical substances were closely knit into business management. (NEDO)

  16. Report of international workshop on technical elements for aviation safety; Koku anzensei kojo no tame no gijutsu kadai ni kansuru kokusai kaigi wo kaisaishite

    Energy Technology Data Exchange (ETDEWEB)

    Terada, H. [National Aerospace Laboratory, Tokyo (Japan)

    1999-06-05

    The international workshop on technical elements for aviation safety was opened in Tokyo on March 15-17, 1999 with 75 domestic and overseas participants, and 18 reports. On aircraft operation, report was made on the research of a practical visual sense supporting equipment for cockpits to reduce workload of crew at takeoff and landing, and improve a safety. On human factor, report was made on the managers` recognition of their responsibility on safety in Titanic accident. On aircraft passenger cabin safety and emergency escape, discussion was made on the order of priority of 30 factors effective for improving a survival rate in crush accidents, and report was made on current R & D of flame retardant interior materials with less toxicity for passenger cabins. On aircraft body structure, report was made on the research on growth and propagation of fatigue cracks by more than 10{sup 8} cycle loading, and the simulation of complex loading to estimate residual lives of body structure. (NEDO)

  17. Research on elaboration of the action plan for the New Earth 21; `Chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Elaboration of the action plan for the New Earth 21 plan proposed by Japan in Houston Summit was researched. In fiscal 1995 three types of energy supply/demand scenarios, sensitivity analysis under various conditions, and cases presupposing CO2 emission regulations or not were evaluated by analysis toward 2050 using the New Earth 21 Model (NE 21 Model). Energy-saving is important, and CO2 recovery/treatment technology is introduced according to CO2 emission regulations, while attention is focussed on biomass energy. The issue of solar and wind power generation is cost reduction. In a presupposed horizontally integrated energy system, methanol represents an important intermediate energy. As a whole, CO2 reduction can be achieved by various combinations of energy-saving, introduction of regenerative energy, and CO2 recovery/treatment technology. Case studies of the action plan were conducted by unifying the evaluation criterion on coal IGCC, photovoltaic generation and biomass. The NE 21 Model was useful for elaboration of the reduction scenarios of CO2 emission. 26 refs., 84 figs., 28 tabs.

  18. Study on the performance improvement of multiblade fans. Effects of suction cones; Tayoku fan no seino kaizen ni kansuru kenkyu. Suction cone no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Kuratani, F.; Ogawa, T. [Hyogo University of Teacher Education, Hyogo (Japan); Yamamoto, S.

    1999-07-25

    In order to improve the performance of a multiblade fan, the effects of three types of suction cones of the fan casing on the fan efficiency and noise are investigated experimentally. The first type of the suction cone is the insertion type, which is inserted into the inside of the fan impeller. The second type is the extrusion type, which extrudes outside from the casing surface. The third type is the combination type of two types. The results of those three types are compared with those of the commonly used suction cone. The followings are made clear: (1) The insertion type and the extrusion type are effective in improving the efficiency and reducing noise. (2) The optimal lengths of the insertion and the extrusion exist. (3) The combination type is more effective in improving the efficiency. (4) The combination type with the skewed cutoff of the fan casing shows the best effect. (author)

  19. Investigation of nitrous oxide (N2O) abatement technologies. 2; Asanka chisso (N2O) no teigen taisaku ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Emission amount of nitrous oxide (N2O) from anthropogenic sources is analyzed, and reduction effects by the abatement technologies are evaluated. The concentration of nitrous oxide in the atmosphere continues to increase and emissions from agricultural and ecosystem sources are drawing particular attention. For the emission of N2O in Japan, 8.28 Gg-N2O per year is emitted from fossil fuel combustion facilities, 6.95 from waste incineration facilities, 22.5 from transportation vehicles including automobiles, 26.7 from the chemical industry including establishments engaged in adipic acid production, 2.1 from sewage treatment facilities including septic tanks, 6.3 from farmland, and 7.1 from livestock excrement. For the N2O abatement technologies for different sources, fuel improvement, high temperature combustion, acceleration of reduction decomposition reaction, and development of catalysts are significant for the combustion technologies. In connection with N2O discharged in the process of adipic acid production, major businesses have internationally committed to up to 99% abatement of the N2O emissions by 1998. With regard to wastewater and sewage treatment facilities and septic tanks, improvement in COD/NO-N ratio, retention period, pH level, and reduction process is pointed out. 204 refs., 70 figs., 53 tabs.

  20. Investigations on measures to reduce nitrous oxide (N2O); Asanka chisso (N2O) no teigen taisaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Discussions were given on measures to reduce N2O as part of the measures to prevent global warming. Nitrous oxide has a long atmospheric lifetime of 150 years, and its greenhouse warming potential will increase by 310 times that of CO2 after 100 years. It can also be a cause of ozone layer destruction. Nitrous oxide is estimated to have influence of about 10% as compared with CO2 even under the present conditions. Discharge of N2O from manufacturing process of adipic acid is aimed to be eliminated totally by 1998. Improvement in efficiency of combustion of fossil fuels and wastes serves most effectively to reduce not only N2O but also CO2. Nitrous oxide generated in sewage treatment as in sewage purifier may be reduced if the batch process is turned into a continuous process, but assistance from policy side would be required for wider adoption of the process conversion. No environmental regulations are applicable to N2O, whereas a problem is present that the number of system installation would not grow because of economic reasons even if the system is feasible technically. Another problem is that the N2O reducing technology is in trade-off relation with other warming gases such as NOx and methane. Comprehensive technological evaluations aimed at optimization must be moved forward in the future. 236 refs., 102 figs., 78 tabs.

  1. Survey on the technological development issues for large-scale methanol engine power generation plant; Ogata methanol engine hatsuden plant ni kansuru gijutsu kaihatsu kadai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Based on the result of `Survey on the feasibility of large-scale methanol engine power generation plant` in fiscal 1992, concrete technological development issues were studied for its practical use, and the technological R & D scheme was prepared for large-scale methanol engine power plant featured by low NOx and high efficiency. Technological development issues of this plant were as follows: improvement of thermal efficiency, reduction of NOx emission, improvement of the reliability and durability of ignition and fuel injection systems, and reduction of vibration. As the economical effect of the technological development, the profitability of NOx control measures was compared between this methanol engine and conventional heavy oil diesel engines or gas engines. As a result, this engine was more economical than conventional engines. It was suggested that development of the equipment will be completed in nearly 4 years through every component study, single-cylinder model experiment and real engine test. 21 refs., 43 figs., 19 tabs.

  2. Theoretical study on composition of gas produced by coal gasification; Sekitan gas ka de seiseisuru gas no sosei ni kansuru kosatsu (HYCOL data no doteki kaiseki)

    Energy Technology Data Exchange (ETDEWEB)

    Kaiho, M.; Yasuda, H.; Kobayashi, M.; Yamada, O.; Soneda, Y.; Makino, M. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In relation to considerations on composition of gas produced by coal gasification, the HYCOL hydrogen generation process data were analyzed. From the fact that CO concentration (Y) decreases linearly with CO2 concentration (X), element balance of gasification of reacted coal was used to introduce a reaction analysis equation. The equation includes a term of oxygen excess {Delta}(amount of oxygen consumed for combustion of CO and H2 in excess of the theoretical amount), derived by subtracting the stoichiometric oxygen amount used to gasify coal into CO and H2 from the consumed oxygen amount. The {Delta} can be used as a reference to oxygen utilization efficiency. An equation for the {Delta} was introduced. Also introduced was a term for steam decomposition amount derived by subtracting the generated steam from the supplied steam. These terms may be used as a clue to permeate into the gasifying reaction process. This suggestion was discussed by applying the terms to gas composition value during operation. According to the HYCOL analysis, when a gasification furnace is operated at higher than the reference oxygen amount, coal supply variation is directly reflected to the combustion reaction, making the {Delta} distribution larger. In an inverse case, unreacted carbon remains in the furnace due to oxygen shortage, and shift reaction may occur more easily even if oxygen/coal supply ratio varies. 6 figs., 1 ref.

  3. Report on investigations and studies on development of materials for hydrogen absorbing alloys; Suiso kyuzo gokin no zairyo no kaihatsu ni kansuru chosa kenkyu hokokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper describes investigations and studies on hydrogen absorbing alloy materials and the technologies to utilize them. In the investigations and studies, literatures were collected and put into order, questionnaire surveys were performed and analyzed, lecture meetings and panel discussions were held, and the discussion results were summarized. In the present status of developing hydrogen absorbing alloys, the current status of and problems in developing such hydrogen absorbing alloys as Ti-based, Mg-based, and rare earth-based alloys were put into order. Discussions were given on prospects of possibilities of developing new alloys, making them amorphous, and putting them into mass production. In the current status of developing the utilizing technologies, such technologies as hydrogen storage systems and heat pumps were put into order and discussed. With regard to problems in hydrogen absorbing alloys, discussions were given on alloy weight, pulverization, activation, heat conductivity, and alloy costs. In discussing the safety, discussions were given on the safety and compliance with related laws and regulations relative to hydrogen transportation using a great amount of hydrogen absorbing alloys, their storage, and heat storage systems. In addition, questionnaire surveys were carried out with an objective to identify the status of developing hydrogen absorbing alloys and needs from the industries. (NEDO)

  4. Study of initial stage in coal liquefaction. Increase in oil yield with suppression of retrogressive reaction during initial stage; Ekika hanno no shoki katei ni kansuru kenkyu. 1.

    Energy Technology Data Exchange (ETDEWEB)

    Uesugi, K.; Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogen transfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic effect between the improvement of liquefaction by suppressing polymerization/condensation at the initial stage of reaction through the prethermal treatment and the effective hydrogen transfer accompanied with the improvement of contact efficiency of coal/catalyst by the concentration of slurry at the stage of liquefaction. 4 refs., 8 figs.

  5. Bridging exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Rinaldi-Montes, Natalia, E-mail: nataliarin@gmail.com [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain); Gorria, Pedro [Departamento de Física & IUTA, EPI, Universidad de Oviedo, E-33203 Gijón (Spain); Martínez-Blanco, David [Servicios Científico-Técnicos, Universidad de Oviedo, E-33006 Oviedo (Spain); Fuertes, Antonio B. [Instituto Nacional del Carbón, CSIC, E-33080 Oviedo (Spain); Fernández Barquín, Luis [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, E-39005 Santander (Spain); Puente-Orench, Inés [Instituto de Ciencia de Materiales de Aragón, CSIC-Universidad de Zaragoza and Institut Laue-Langevin, BP 156, F-38042 Grenoble Cedex 9 (France); Blanco, Jesús A. [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain)

    2016-02-15

    Among all bi-magnetic core(transition metal)@shell(transition metal oxide) nanoparticles (NPs), Ni@NiO ones show an onset temperature for the exchange bias (EB) effect far below the Néel temperature of bulk antiferromagnetic NiO. In this framework, the role played by the magnetism of NiO at the nanoscale is investigated by comparing the microstructure and magnetic properties of NiO and Ni@NiO NPs. With the aim of bridging the two systems, the diameter of the NiO NPs (~4 nm) is chosen to be comparable to the shell thickness of Ni@NiO ones (~2 nm). The EB effect in Ni@NiO NPs is attributed to the exchange coupling between the core and the shell, with an interfacial exchange energy of ΔE~0.06 erg cm{sup −2}, thus comparable to previous reports on Ni/NiO interfaces both in thin film and NP morphologies. In contrast, the EB detected in NiO NPs is explained in a picture where uncompensated spins located on a magnetically disordered surface shell are exchange coupled to the antiferromagnetic core. In all the studied NPs, the variation of the EB field as a function of temperature is described according to a negative exponential law with a similar decay constant, yielding a vanishing EB effect around T~40–50 K. In addition, the onset temperature for the EB effect in both NiO and Ni@NiO NPs seems to follow a universal dependence with the NiO crystallite size. - Highlights: • Comparison of the exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles. • Universal temperature dependence of the exchange bias effect. • Suggested similar physical origin of the effect in both systems. • Size and crystallinity of the NiO shell hold the key for exchange bias properties.

  6. ZnNi data

    Science.gov (United States)

    2014-11-01

    information only) BE AMERICA’S BEST STRENGTH AND HONOR Additional LHE Zn-Ni Hydrogen Re-Embrittlement Testing  The original LHE Zn-Ni test...follows:  LHE Zn-Ni tank contamination • Spring ‘09 Lab analysis showed organic contamination • The PVC tank liner had begun to break down and had...to be replaced in the Summer ‘09 with a more robust grade of PVC liner • Two years operating with new liner with no problems  Inconsistent plating

  7. OpenNI cookbook

    CERN Document Server

    Falahati, Soroush

    2013-01-01

    This is a Cookbook with plenty of practical recipes enriched with explained code and relevant screenshots to ease your learning curve. If you are a beginner or a professional in NIUI and want to write serious applications or games, then this book is for you. Even OpenNI 1 and OpenNI 1.x programmers who want to move to new versions of OpenNI can use this book as a starting point. This book uses C++ as the primary language but there are some examples in C# and Java too, so you need to have about a basic working knowledge of C or C++ for most cases.

  8. Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

  9. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

  10. Research achievement report for fiscal 1998 on the development of high-performance industrial furnaces. Research and development of high-performance industrial furnaces and the like (2); 1998 nendo koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusho. Koseino kogyoro nado ni kansuru kenkyu kaihatsu (2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Volume 2 named above contains part of research achievement reports and individual research achievement reports. The aluminum melting furnace working group research achievement report covers aluminum melting furnace operating patterns, concentrated impinging flame mode and dispersed impinging flame mode, and honeycomb and ball structures in heat storing bodies. The tubular heater working group report mentions the application of this facility to oil heating furnaces, studies and investigations for the embodiment of real systems using the tubular heater, and tests conducted in a furnace with plural heating tube lines. The individual research achievement reports elaborate on the development of technologies of heat transfer optimization under unsteady conditions in the steel material heating process, research and development of high-efficiency heat transfer technologies, development of heating furnace geometry optimization technologies, research and development of a high-performance controlled atmosphere heat treatment furnace, development of high-efficiency heat transfer technologies in high-temperature jet flame heating, development of heat uniformity improvement technologies for example for the steel material heating process, construction of optimum combustion control technologies for the regenerative burner furnace, research concerning laser-aided measurement in industrial furnaces, etc. (NEDO)

  11. Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

  12. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

  13. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

  14. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

  15. Fiscal 1996 survey of potential international cooperation for a long-term scenario on CO2 reduction; 1996 nendo CO2 sakugen ni kakawaru choki shinario ni kansuru kokusai kyoryoku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of working out a CO2 reduction scenario and a CO2 policy introduction scenario, a survey was conducted of comparisons between ten and several models which are world-known and models of the New Earth 21, potential international cooperation to be carried out in the future, etc. The survey included organizations which are developing CO2 policy evaluation models, survey reports made in the past, details of literature for the analysis and arrangement. From the result, details of the questionnaire survey and organizations to be surveyed were decided on for the questionnaire survey. Objects for the survey were 7 countries and 22 organizations, and survey items were places for information exchange, sending/receiving of researchers, exchange of input data, comparative calculation based on the common database, joint research work, economy, the carbon tax, impact, renewable energy, how to handle and think of the carbon isolation, etc. As a result of the survey, proposed were a workshop on CO2 reduction, a comparative study of simulation models, etc. 25 refs., 50 figs., 12 tabs.

  16. Study on the characteristics of earthquake ground motion in the Hanshin area based on microtremor measurements; Bido kansoku ni motozuku Hanshin chiiki no jiban shindo tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H.; Seo, K.; Yamanaka, H. [Tokyo Institute of Technology, Tokyo (Japan)

    1997-05-27

    The Hyogoken-nanbu earthquake in 1995 was a local earthquake that has hit directly a large urban area, having caused damages the greatest since the War mainly in the city of Kobe. The present study has noticed the areas of Sumiyoshi, Nada Ward, Kobe City and Nanbu, Nishinomiya City where damages show different distribution; elucidated the characteristics of earthquake ground motion based on microtremor measurements; and discussed the relation thereof with the earthquake damage distribution. It was verified that microtremors and seismic motions are in rough agreement in the Sumiyoshi area, by comparing and discussing the spectrum ratio between the microtremors and the seismic motions. No correspondence was recognized in the Sumiyoshi area between distribution of the average microtremor spectrum ratio with cycles of 0.2 to 0.8 second and distribution of damages caused by the Hyogoken-nanbu earthquake. The ground characteristics evaluation alone is insufficient to explain distribution of the damages in a relatively wide range in the city of Nishinomiya, for which effects of distance decay should be taken into consideration. 6 refs., 7 figs.

  17. Considerations on FEM modeling in analyzing buckling and plastic collapse of a detection control; Boto panel no zakutsu sosei hokai kaiseki ni okeru FEM model ka ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yao, T.; Fujikubo, M.; Yanagihara, D.; Irisawa, M. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    Buckling and plastic collapse of upper decks and bottom outer plates of a hull results directly in longitudinal bending collapse of the hull. Therefore, discussions were given on analysis for pressure destruction strength of a detection control panel which assumes an upper deck and a bottom outer plate. Pressure destruction behavior of the panting panel is a complex phenomenon accompanying non-linearity and geometrical non-linearity of the materials. Its whole phenomenon may be analyzed by using the finite element method (FEM) as a principle, but the analysis is not efficient. Therefore, considerations were given in relation to modeling when using the FEM. The considerations were given on a panel attached with flat steel panting members with respect to the modeling scope which considers the buckling mode according to the aspect ratio of the panel partitioned by the deflection control members. If the local buckling mode of the panel is an even number wave mode in the longitudinal direction, a triple span model is required. A modeling scope for a case of being subjected to water pressure and in-plane compression was considered on a panel attached with angle-type steel members having non-symmetric cross section. In this case, a triple bay model is more preferable to reproduce the behavior under water pressure loading. 1 ref., 6 figs.

  18. Report on the research cooperation promoting project in fiscal 1998. Research cooperation related to the mine waste water treatment technology utilizing biomass; 1998 nendo kenkyu kyoryoku suishin jigyo hokokusho. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes the achievement in relation with the mine waste water treatment technology utilizing biomass, from among the promotion projects for research cooperation with China. Waste water is converted into ferric iron (Fe{sup 3+}), which precipitates at low pH, by utilizing iron oxidizing bacteria which use ferrous iron (Fe{sup 2+}) in the waste water as the energy source, and is precipitated and removed by using low-cost calcium carbonate as a neutralizing agent. Fiscal 1998 has performed eight site surveys with 47 persons in total. The main survey items are the study and guidance of pilot plant operation and the survey on measures to prevent occurrence of contamination by heavy metals in Wushan Mine. Additional site surveys were made at Dexing Mine and Yinshan Lead/Zinc Mine. Continued from fiscal 1997, consumables required for the pilot plant were purchased, and items of the bench-scale testing equipment used by Japan for domestic researches (an oxidation and neutralization testing equipment and a copper recovering and testing equipment) were transported to China. The operation research data of the pilot plant were put in order and analyzed. This paper summarizes the concept design of the shaft waste water treatment facilities for the north mine in Wushan Mine, and the surveys on measures for heavy metal contamination sources. (NEDO)

  19. Report on research cooperation for bio-aided treatment of waste water from mining pits, conducted in FY1996. Data edition; 1996 nendo bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku hokokusho. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report carries the results of (1) surveys on properties of waste water discharged from pits in Wushan Mine in Province of Jiangxi, China, (2) monitoring the environments around the mine, (3) monitoring the environments around the mine (photographs) and (4) surveys on properties of waste water discharged from pits in other mines, and also outlines (5) the Chinese research activities. More specifically, it carries (1) water analysis results of pH and heavy metals at -40mL and -160mL pits and raw water pit on the earth's surface, (2) analysis results of pH and heavy metals for water discharged from the mine at 15 points, 7 at the north of the mine, 4 at the south of the mine, 2 at the tailings, 1 at Chihu, and 1 at the eastern tailings, (4) the data regarding waste water discharged from pits in 5 mines in the same province, including copper, copper-sulfur and copper-zinc mines, and (5) results of the (bacteria-culturing tests for high-efficiency oxidation of iron) carried out in Wushan Mine. The tests comprised the nutrient addition, raw water load and residence time tests, and the results of each test are reported. Fe (II) is oxidized to 95 to 98% at a residence time of 0.75 hours. (NEDO)

  20. FY1998 report on a survey related to joint utilization of welfare device development data using an international network; 1998 nendo kokusai network ni yoru fukushi kiki kaihatsu data no kyodo riyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey was made in relation with joint utilization of welfare device development data using an international network. Developing welfare devices requires data from ergonomic and medical systems, while the cope of the objects is wide, and the kinds are various. For proliferation of welfare devices, system compatibility evaluation including that on using environment is important, including living environments that are different by countries. The present survey has identified how data for aged, handicapped and help-needing persons are accumulated and utilized in research organizations in America and Europe for both of the ergonomic and medical areas. The survey also investigated major academic societies in overseas countries, and collected database and academic network information that support the advanced research and development. At the same time, investigations were also made on organizations and corporations who are moving forward the efficient data utilization. Welfare device and service information providing systems in Japan were investigated to compare them with the trends in other countries. Conceptions and methods were compiled to utilize data internationally and jointly. Database models for device development were considered, and a proposal was made on structuring a research and development supporting database, and the operation method thereof. (NEDO)

  1. Study on heat collector of the solar system utilizing outdoor air. Experimental results in cases of cold and warm regions; Gaiki donyushiki solar system no shunetsubu ni kansuru kenkyu. Kanreichi to ondanchi ni okeru shunetsu jikken to kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Komano, S.; Ebara, Y. [OM Solar Association, Shizuoka (Japan); Wada, H. [Wada Building Constructors Co. Ltd., Hokkaido (Japan)

    1996-10-27

    An experiment on heat collection was made in the heat collector of a solar system utilizing outdoor air in cold and warm regions. In this system, outdoor air is heated by the air circulation layer on the roof exposed to solar radiation. The heated air is supplied to the object space for heating and ventilation. In the experiment in a cold region, the heat collection characteristics can be adjusted by putting a baffle plate in the air duct according to the experiment of a glass heat collector. The heat collecting air layer on only the iron roof may leak or freeze in the region subject to coldness or heavy snowfall. Therefore, preheat forms the space of a garret, and the preheat temperature comparatively becomes low. The data in which the heat collection characteristics can be adjusted using only a glass heat collector is required corresponding to the regional situation. In the experiment in a warm region, an experiment was made inclusive of the preheat for which outdoor air is absorbed at the eaves. As a result, the heat collection characteristics of preheat were improved. Moreover, a heat collection temperature of about 60{degree}C was obtained on the heat collection surface including the preheat. 1 ref., 12 figs., 3 tabs.

  2. Model experiment on change of seismic properties of a fracture caused by injecting/draining water; Chusui/haisui ni yoru kison kiretsu no dansei denpa tokusei no henka ni kansuru model jikken

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Koizumi, T.; Sassa, K. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1997-05-27

    Effect of water injection/draining on elastic waves penetrating through cracks is examined by measuring elastic waves before, during, and after the injection/draining of water into/from cracks in presence in granite. Two blocks of rock, with their crack-containing surfaces in contact with each other, are placed in a vessel, and water injection/draining is done through a hole on a vessel bottom side so that water will penetrate into the cracks. When the blocks are dry, there is almost no contact between the cracks, and so no crack penetrating waves are observed. Crack penetrating waves are produced when water is injected, and the position of the receiver sensing the penetrating waves changes as the water level rises. When the water level is lowered from the high water level, the waveform changes again as the level changes. The change in waveform is not so remarkable, however, as that observed during water injection thanks to the water residual in the cracks. It is now inferred that crack investigation is more effective when it is carried out with water being injected into dry cracks. The difference produced between the dry state and wet state when water is injected into dry cracks is used to detect the presence of cracks in this experiment, and this may be applied also to the investigation of cracks in the shallow part of the ground. 4 refs., 11 figs.

  3. Study on the evaluation method of debris flow and the hillside landslide scale of debris flow in nazardous torrent; Dosekiryu kiken keiryu ni okeru hokai kibo no hyoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, S. [National Defense Academy, Kanagawa (Japan); Ishikawa, Y. [Public Works Research Inst., Tsukuba (Japan); Mizuyama, T. [Kyoto Univ., Kyoto (Japan). Faculty of Agriculture; Furukawa, K. [Yamaguchi Univ., Yamaguchi (Japan). Faculty of Engineering; Araki, Y. [Chuden Engineering Consultants Co. Ltd., Hiroshima (Japan)

    1995-09-20

    Among natural disasters, earth and sand disaster, such as landslide, landslip, and so forth, including debris flow occurs all over the country every year. Among the earth and sand disasters, debris flow disaster presents the most large destructive power phenomenon, producting the most mass of earth and sand. The debris flow has a following characteristics, translation distance of earth and sand is long and the mass of earth and sand is carried away owing to take in unstable earth and sand deposited on torrent floor with flowing, therefore, the damage is very wide rangs to downstream area. An investigation of debris flow in hazardous torrent was conducted all over the country which estimated the degree of risk in debris flow. From the investigation, debris flow was evident in a lot of mountain torrents. In this study, the present evaluation on the degree of risk in debris flow was examined and the evaluation method of debris flow and hillside landslide scale which was used land map as the only factor, for example, the east area of Nagasaki City that was mostly damaged by debris flow in July, 1982, were proposed. 13 refs., 13 figs., 7 tabs.

  4. Research cooperation project in fiscal 1998. General report on research cooperation related to mine waste water treatment technology by utilizing biotechnology; 1998 nendo kenkyu kyoryoku jigyo. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kenkyu kyoryoku sokatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes cooperative development of bio-treatment technology for mine waste water generated by operating mines in China. Certain types of bacteria have capability to oxidize ferrous iron in the waste water into ferric iron ions. The bacteria cause ferric iron oxides in low pH regions to get deposited, and can remove them from sedimentation by using cheap calcium carbonate as a neutralizer. Volumetric reduction in waste sediments may also be achieved during removing heavy metals in a pretreatment process. Great advance may be expected in taking actions to prevent water quality contamination. This paper summarizes activities taken in fiscal 1998. Eight site surveys in total were carried out using 47 persons in total. Major activities included operation study guidance of a pilot plant, and surveys for measures on heavy metal generation sources in Wushan Mine. In addition, site surveys were performed at Dexing Mine and Yinshan Zinc Mine. Subsequently from fiscal 1997, a bench scale testing equipment used in Japan and consumables were transported to China. The operation study data on the pilot plant were put into order and analyzed. Concept design was also made on a waste water treatment facility for Wushan Mine. (NEDO)

  5. Study on vapor film collapse behavior on high temperature particle surface. 2nd Report. Effect of subcooling on micro-mechanism; Koon ryushi hyomenjo no jokimaku hokai ni kansuru kenkyu. 2. Bishiteki hokai kyodo ni oyobosu subcooling no eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Abe, Y.; Tochio, D. [Yamagata University, Yamagata (Japan). Faculty of Engineering

    2000-02-25

    Thermal detonation model is proposed to describe vapor explosion. According to this model, vapor film on pre-mixed high temperature droplet surface should be collapsed for the trigger of the vapor explosion. It is pointed out that the vapor film collapse behavior is significantly affected by the subcooling of low temperature liquid. However, the effect of subcooling on micro-mechanism of vapor film collapse behavior is not experimentally well identified. The objective of the present research is to experimentally investigate the effect of subcooling on micro-mechanism of film boiling collapse behavior. As the results, it is experimentally clarified that the vapor film collapse behavior in low subcool condition is qualitatively different from the vapor film collapse behavior in high subcool condition. In high subcool condition, instability of the vapor film dominates the vapor film collapse on the particle surface. On the other hand, micro-mechanism at the interface between vapor and liquid such as micro-jet is dominant in low subcool condition in case of vapor film collapse by pressure pulse. (author)

  6. Study on construction of temporary dwellings and problems caused by living long time on Hanshin-Awaji Great Earthquake; Hanshin / Awaji daishinsai ni okeru okyu kasetsu jutaku no secchi to chokikan shiyo suru baai no kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Nakamura, Y. [Nagasaki Univ. (Japan)] Shimizu, Y. [Kumagai Gumi Co. Ltd., Tokyo (Japan)

    1998-10-20

    Two years after the above-titled earthquake, an examination was performed on inhabitants in the temporary dwelling houses in Kobe, center of the calamity, and problems caused by a long stay there were clarified together with a grasp of the evolving problems by comparing the result of survey carried out immediately after the disaster. The number of such temporary dwelling houses amounted to 29,128 within Kobe City and 3,168 outside of the city. According to the room arrangement, they were either one f 4 types : 2-rooms with a kitchen, 1 room with a kitchen, dormitory and those specifically for aged persons. There were 59,449 applications at the first offer of 2,702 houses. The priority of their assignments and so on are explained. As for the housing structure, numerous complaints concerned with the room temperature, noise and so forth. As for the living environment, lack of nearby commodity shop, omission of transportation access, ill drainage of the housing sites were pointed out and the matters of demand to the local authorities included the installation of mail post and street lights. As for the health management, insomnia, stiff shoulder, lumbago and other bad physical conditions were revealed. The financial difficulty and the high house rent were obstacles to migrate to other places. The prolonged temporary lives worsened the apprehension of dwellers for the earthquake, typhoon, fire and alike. Some features for the calamity are described in comparison with the result of survey on those who were compelled to live under similar conditions by the eruption of Mr. Fugen. 6 refs., 13 figs., 15 tabs.

  7. FY 1997 report on the modification of dental materials with Ag for improvement of antibacterial activity; 1997 nendo chosa hokokusho (gin ion ni yoru shikayo zairyo no kokinsei fuyo ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Improvement of an antibacterial activity is one of the issues in modification of artificial teeth for an aged society. Study was made on improvement technique of an antibacterial activity with Ag ion as secondary corrosion measures. Partial gaps of dental materials themselves and gaps between materials and peripheral tissues causes bad breath or bad teeth through propagation of disease germs. Ag ion is harmless and has an antibacterial activity for bio-tissues from a macro-viewpoint, however, only corrosion germ causing bad teeth in mouths should be sterilized by controlling an elution rate of Ag properly. The antibacterial activity was controlled by controlling Ag ion implantation depth and rate, and Ag elution rate for dental materials. Experiment was made on an IMZ twinplus specimen implanted with Ag ion and an Ag thin film-coated specimen using beagle dog in comparison with an unmodified specimen. As a result, the very favorable antibacterial activity was obtained. Ag ion is effective for prevention of endogenous infectious disease due to mouth germs in dental surgery. 3 refs., 47 figs., 10 tabs.

  8. Fiscal 1997 survey of the overseas coal import base preparation/improvement. Survey of a coal flow in China; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. Chugoku ni okeru coal flow ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper surveyed the preparation of the coal transportation infrastructure, status of its running, economical efficiency, etc. in terms mainly of the trend of coal production/consumption in China, and coal railroad/water transportation and electric power transportation by mine-mouth power generation. From the survey, the following conclusions were obtained. As to the coal which China uses as a main energy for maintaining the present high economic growth as targeted, there will remain the coal transportation problem between production site (north and west) and consumption site (east and south) still in the future (in 2000 and 2010). China is now facing with a big turning point in a socioeconomic aspect. The advancing opening market policy brought steep rises in energy prices such as coal and electric power, which is affecting various fields. Further, the energy related laws, which were unprepared, are abruptly being prepared, and the environment for the introduction of foreign investment, which is expected to be accelerated, is being prepared. In the future, attention should be paid to environmental problems such as air pollution, acid rain and global warming. 48 figs., 96 tabs.

  9. Research and survey report of FY 1997 on the CO2 balance for high-temperature CO2 fixation and utilization technology; 1997 nendo chosa hokokusho (nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this research is to clarify the application condition and effectiveness of high-temperature CO2 fixation and utilization technology. To evaluate the present process, it was compared with others, such as separation using a polymer membrane, physico-chemical absorption process, adsorption process, hydrogen contact reduction process, and biological fixation. The development trends of absorption, membrane, adsorption, and cryogenic separation were investigated. The questionnaire was carried out about the separation technologies which are in the stage of performance test using actual gas, to arrange and compare the data and information. The current trends of chemical and biological CO2 fixation and utilization technology were also investigated for arranging the subjects. High-temperature CO2 disposal by the carbonation in concrete waste has been studied, to clarify its application conditions and effectiveness. In order to compare the separation technologies, treatment processes of CO2 in the exhaust gas from boilers of LNG power generation and coal fired power generation were simulated. These processes were simulated by ASPEN PLUS for the modeling. Trends of application of ASPEN PLUS and collection of information were surveyed by participating in the ASPEN WORLD. 103 refs., 51 figs., 55 tabs.

  10. Ab initio calculations for a relationship between impact sensitivity and molecular structure in HMX polymorphs. HMX kessho takei no shogeki kando to bunshi kozo tono sokan ni kansuru hi keikenteki bunshi kidoho ni yoru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kono, Y.; Tsuchioka, T.; Hashizume, T. (Chugoku Kayaku Co. Ltd., Hiroshima (Japan)); Azuma, N. (Ehime Univ., Ehime (Japan). Faculty of General Education); Maekawa, K.; Imamura, A. (Hiroshima Univ. (Japan). Faculty of Science)

    1992-10-31

    HMX, nitramine-based high performance explosive, is a ring nitramine compound called chemically octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine, and has 4 kinds of crystal polymorphs, [alpha], [beta], [gamma] and [delta]. Values of impact sensitivity of these four crystal polymorphs are different each other and the most stable [beta] is being produced. In this paper, ab initio [beta] calculations (STO-3G) based on the molecular structure in the crystal have been conducted on all of the above HMX crystal polymorphs and the X-ray structural analysis has also been done on the molecular structure of [beta]. As a result, 0.032 has been obtained as the ultimate R index for 734 independent reflections. Concerning the crystal, it is single crystal, its space group is P2[sub 1] /n, and its lattice constants are [alpha] = 6.5347(4), b=11.0296(6),c=7.3549(5), [angstrom] [beta] =102.689(5) [degree], and Zeta=2. When calculations are made on these bases, all energy and impact sensitivity correlate except[gamma]. 21 refs., 6 figs., 7 tabs.

  11. FY1995 high techniques of measuring for sensation, cognition arid behavior in the man-products-environment interface; 1995 nendo seihin kankyo interface ni okeru kankaku ninchi kodo keisoku kodoka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    We measure the distribution of activation locus of brain cortex area and its time-sequence against various kinds of stimulus by using the fMRI that can visualize directly brain activities. Next, we try to make a simulation model of the information processing system of brain, and aim at establishment of new evaluation index for environment-human interface based objectively or quantitatively on brain activity data. we challenged to examining quantitatively brain activities by using functional MRI instrumentation technique. We made a effort to acquire functional MRI technique by repetition of pilot studies, and were successful in visualization of visual cortex (primary sensory area). In the latter period, sensory areas whose function had not been studied sufficiently and higher functional areas of brain which related to memory, attention and emotion were studied. The identification of action locus of gustatory area was tried using functional MRI studies. In studies about the ability of spatial attention, experiments elucidating locus participating in space perception and attention and its function were advanced. It was suggested that activation locus of brain was different between a color-form matched stimulus and a mismatched stimulus. The MRI measurement added the information of musculoskeletal system to the current analysis of human body configuration and gesture character, and a more detailed analysis of human body became possible. This is, an useful analysis was suggested by a plan of shoes pattern. (NEDO)

  12. Fiscal 1998 research report on the metal thin film formation by UV laser photodecomposition of adsorbed organic metal compounds; Kyuchaku yuki kinzoku kagobutsu no shigai laser ko bunkai ni yoru usumaku sakuseiho ni kansuru kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research was made on the new thin film formation method depositing metal or metal compound thin films by excimer laser photodecomposition of organic metal compounds condensed onto substrates at lower temperature. The organic metal compound was condensed onto cooled substrates (glass, semiconductor Si) from gas-phase iron pentacarbonyl below 250K in vacuum. KrF excimer laser was used as UV laser. The thin films with electric conductivity and metallic luster were deposited onto the laser irradiation areas of both substrates below 250K. The thin films were deposited only by proper laser pulse irradiation fluence (energy/unit area), and are composed of iron or its oxide. The deposition rate is estimated to be nearly 0.5nm/s, and precise control of film thicknesses is possible. Formation of pure metal and metal oxide thin films with various film thicknesses and compositions is probably possible by controlling thin film formation conditions. The iron thin film with characteristics of magnetic thin films is applicable to various fields, and is also important as the base for forming alloy films and multi-layered films. (NEDO)

  13. Investigation on the dynamic response and strength of very long floating structures by beam modeling on an elastic foundation; Dansei shishojo no hari model ni yoru chodai futai kozo no doteki tawami kyodo tokusei ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tsubogo, T.; Okada, H. [University of Osaka Prefecture, Osaka (Japan). Faculty of Engineering

    1997-08-01

    A very large floating structure was replaced with the beam on an elastic foundation to examine the response characteristics in waves. Another evidence was regularly and numerically given for the basic characteristics of a very large floating body Suzuki found. New information was also obtained. The frequency response is mainly classified into a wave number control area and proper frequency control area when buoyancy elasticity exists. When the buoyancy structure is long and flexible, the proper frequency becomes continuous and the frequency control area becomes a resonance area. In the wave number control area, the Suzuki`s characteristic wave number becomes a control parameter, and various characteristic values are indicated by characteristic wave numbers. The response in the wave number control area becomes quasi-static when the distribution mass of buoyancy is fully small. The design in which the distribution mass of buoyancy is fully large must be avoided. In the displacement amplitude, the mass on the free end is severest. The proper frequency of vertical vibration relatively moves to the high-frequency side when buoyancy is considered as an elastic foundation. Attention must be thus paid to the proper frequency of vibration on the horizontal surface. 9 refs., 12 figs., 3 tabs.

  14. Study of vortex dislocation in the wake of a flat plate with finite thickness; Yugen atsusa heiban koryu ni okeru uzu ten'i kozo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Abe, S.; Maekawa, H. [University of Electronic-Communication, Tokyo (Japan)

    2000-09-25

    Wake structures of a flat plate with finite thickness are studied using the rake of X-wires techniques. Parallel and oblique shedding modes in the wake flow are investigated. These modes depend on the flat plate end conditions. In the present paper, we demonstrate that manipulation of the end conditions yields a vortex dislocation that appears periodically at the same location. Vortex linkup dynamics phenomena in the dislocations are observed with smoke-wire flow visualization. Flow patterns of dislocation are analyzed by mean of the pseudo-flow visualization of the rake data. The linkup structure due to a misfit of two oblique shedding vortices appears periodically in the flow patterns. Evolutions of the power spectra of velocity fluctuations explain the generation of large-scale turbulent structure downstream due to the growth of a low-frequency mode and the cascade process of low/high frequency components. (author)

  15. Fiscal 1993 investigational study of a model of international cooperation for an environmentally harmony type green technosystem; 1993 nendo Oshu ni okeru haikibutsu shori oyobi recycle no doko ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    For the natural environment preservation, effective utilization of resources, and maintenance of the ecosystem, an international cooperation model was proposed for the environmental harmony type green technosystem. A comprehensive evaluating analysis of a green forest resource, etc. as the global resource, and an intensive extraction of subjects and needs was made. The analysis was conducted of technical possibility and abstract business development effects toward the industrialization with high values added which is in harmony with the environment. As a case study, the Papua New Guinea area, Malaysia was selected and re-evaluated. For this typical tropical forest area, a new technical system was studied based on the natural environment, industry/economy, social/cultural assessment, etc., and a model for industrializing new international cooperation was proposed. For the model making for industrialization, various steps to be taken and conditions to be prepared were studied and arranged for the realization. Upon going ahead with the international technical cooperation, Japan, a large lumber consuming country, needs to always consider the fostering and effective use of lumber resource in particular. 27 refs., 28 figs., 30 tabs.

  16. Study of a fuel injection quantity sensor in diesel engine. Part 3. Experimental evaluation of the improved type micro turbine sensor; Diesel kikan ni okeru nenryo funsharyo sensor no kenkyu. 3. Funsharyo keisoku no seido kojo ni kansuru jikken hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Maehara, H.; Iwasaki, T.; Kobayashi, T. [Zexel Corp., Tokyo (Japan)

    1997-10-01

    A Micro Turbine Sensor has been developed to measure fuel injection quantity and injection rate. Previous reports described results of experiments on the MTS which were carried out under steady and unsteady flow conditions. The MTS has been improved in shape of a holder tip and a detecting procedure for rotating speed of a turbine. As a result revolution speed of the turbine increased 18% over the conventional type holder under steady flow condition. Furthermore the measurement resolution of the MTS came up to about 2(mm{sup 3}/pulse) at 20(mm{sup 3}/stroke) under intermittent spray conditions using fuel injection pump. 11 refs., 11 figs., 1 tab.

  17. Study of solute incorporation into ice-layer on freeze concentration with ice-lining; Ice lining toketsu noshukuho ni okeru hyosho sochu eno yoshitsu torikomi ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, Y.; Shinozaki, K. [Fujisawa Pharmaceutical Co. Ltd., Osaka (Japan); Hirata, Y. [Osaka University, Osaka (Japan)

    1997-07-10

    The mechanism of solute incorporation into an ice-layer in freeze concentration with ice-lining was studied by changing the impeller speed N and the difference between the brine temperature and the freezing point of the feed solution {Delta}T in 10 kg/m{sup 3} CCNa solution. The effect of N on the apparent partition coefficient of the solute K, is more serious than that of {Delta}T. The growth rate of the ice layer is 10{sup -7} - 10{sup -6}m/s under the condition of {Delta}T=2.8 - 7.9degC and N = 20-400 min{sup -1}. The growth rate had a little effect on solute incorporation into the ice-layer. K values depended on the surface condition of the ice layer, which is effected by the mixing speed of the impeller. The ice layer formed at low mixing speed has a complex rough shape, and has much solute because of adhesion to a large surface area. Therefore, it is recommended that freeze concentration is performed by making an ice layer with smooth surface at high mixing speed. 9 refs., 6 figs.

  18. Reports on 1981 result of Sunshine Project. Research on conditioning required for industrialization of new energy technology; 1981 nendo shin energy gijutsu kigyoka ni hitsuyona joken seibi ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    This research was intended to establish foundation for the coming new energy era, by clarifying all interfering elements and taking counter measures, in further spreading and promoting the new phase of new energy technology development under the Sunshine Project. With the public section as the main body, studies were made in the technological aspect as well as the legal/institutional aspects, and also an investigation was conducted of the cases of introducing new energy from overseas. In the subject research, with 1990 set as the target year, the following examinations were carried out for the purpose of concretely estimating the situation of introducing new energy into the society in Japan at such point in time. The examinations were to study the feasibility of substitution with new energy in fiscal 1990 on the present level of oil consumption; to extract problems on the basis of the results and examining a policy of introducing and promoting new energy; and, to investigate on the spot, as a case study in building a coal liquefaction plant in a coal production area overseas, a relation with the energy policy of the producing country in implementing the overseas operation and importation of liquefied oil so produced, etc. (NEDO)

  19. Research report of fiscal 1997. Survey on creation of high-efficiency renewable resources, and bioconversion technology; 1997 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabi ni bioconversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Survey was made on material production technology using creation technology of high-efficiency renewable resources (photosynthesis reaction of plants). Industrially usable plant resources in overseas countries and Japan were arranged, and plant resources unused for food were also surveyed. The present state of genetic engineering necessary for metabolic engineering of higher plants such as fit and high-expression technology of genes, plant cell cultivation, and control technology of plant cell multiplication is described, and elementary technologies required for future gene-recombined plants are predicted. Survey was also made on the trend of creation technology of industrial plants for fat and oil, biodegradable polyester, amino acid, cellulose, fiber (cotton) and forest wood. A patent list on plant biotechnology was prepared, and study on bioconversion of plant resources was also surveyed. Overseas R & D trends on conversion and effective use technologies of renewable bio- resources are reported, and process design and its profitability were evaluated through a case study. 414 refs., 87 figs., 55 tabs.

  20. Survey on actual status of R and D fund assistance in the U.S.A.; Beikoku ni okeru kenkyu kaihatsu shikin enjo no jittai nado ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    As a basic survey to serve for establishment of science and technology policies, a survey was carried out on the actual status of R and D fund assistance in the U.S.A., roles of the government and civil sectors, and how they are interrelated. The survey was performed in detail on the following items: the assistance and cooperation measures taken by the U.S. government, and technological policies of the U.S. government; fund subsidies and policies toward technological research and development provided by the U.S. government; research and development plans and projects being the object of the subsidies given by the U.S. government; assistance and cooperation of private organizations for financing research and development activities in the U.S.A.; cooperation and joint works among industries, the government and universities (research consortiums) in the research and development activities; legal assistance policies for research and development in the U.S.A., the favorable tax system for research and development, the 1984 National Joint Research Act, and the actual status and analysis of the legal assistance policies in the U.S.A. for aiding research and development tests. (NEDO)

  1. Fiscal 1999 research result report. Research on improvement of boiling heat transfer characteristics by photocatalyst wall; 1999 nendo hikari shokubai hekimen ni yoru futto netsu dentatsu tokusei kaizen ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research was made on improvement of the wettability and boiling heat transfer characteristics of a photocatalyst wall. Measurement experiment of the wettability was made for anatase type titan oxide-coated Al, SUS and Pb plates, rutil type titan oxide-flame coated SUS plate, raw plate, and oxide-plasma coated titan plate. In the ground experiment, the contact angles of distilled water and oil on specimen surfaces were measured. In the microgravity experiment, falling droplet images were recorded by using the facility of Japan Microgravity Center (JAMIC). For obtaining the effect of radioactive emission, UV irradiation, {gamma} ray and neutron beam irradiation by nuclear reactor, and {gamma} ray irradiation by Co-60 were carried out. As the experiment result, the rutil type titan oxide-flame coated SUS plate, nonconductor-coated titan plate, and zircaloy plate showed large improvement of the wettability by {gamma} ray irradiation with Co-60. It was also confirmed that in particular, titan shows the large effect of radioactive emission, and the wettability deteriorates rapidly after {gamma} ray irradiation. (NEDO)

  2. On dynamic response analysis of base-isolated structures for the Northridge earthquake and the Hyogo-ken Nanbu earthquake; Chokka jishin ni taisuru nenshin kozo no oto kyodo ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takayama, M.; Morita, K. [Fukuoka University, Fukuoka (Japan). Faculty of Engineering

    1995-09-01

    The January 17, 1995, Hyogo-ken Nanbu earthquake was occurred. This earthquake was the most damaging earthquake to have struck Japan since the great Kanto earthquake. In Los Angela area, the Northridge earthquake was occurred at January 17, 1994. In this earthquake, the large acceleration over 1G was observed. Two base-isolated buildings (computer center and research facility) in Kobe-city, and USC Hospice (base-isolated building) in Los Angeles survived these big earthquakes. In this paper, the observed response of these base-isolated buildings was introduced and the performance of base-isolated buildings was discussed. And the dynamic response analysis was carried out using the observed ground motions during the two big earthquakes. As the results, the acceleration response of base-isolated buildings which isolated period Tf is over 4 sec was below 0.1-0.2G, and the relative displacement of isolated story was under 30-50cm. 13 figs., 4 tabs.

  3. Study on the reaction mechanism of oxygen-added enzyme for effective use of unused seaweeds; Miriyo kaiso no shigenka ni shisuru sanso tenka koso no hanno kiko ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For effective use of unused seaweeds, efficient search of available microorganism systems and their conversion for effective use were studied. Since generally found Phaeophyceae includes a large amount of polyphenol such as phlorotannin, it is refused by plant-eating animals, inhibits protein from effective absorption, and is inadequate for livestock feed because of tasteless. Bacteria Rhodococcus sp. PG7-2 was isolated which can be effectively increased using phloroglucinol as substrate. Participation of oxygen- adding enzyme was suggested in the initial stage of decomposition which adds molecular oxygen to aromatic rings. In the experiment using combinations of extracted and isolated enzymes and various coenzymes, no significant decomposition was observed. Since phlorotannin of Phaeophyceae is the polymer which shows a matrix-like extent through difficult-to-decompose bond such as biphenyl bond and phenyl ether bond, its decomposition by one kind of bacterium is extremely difficult. Search of decomposition systems of polymer remains as the future issue. 15 refs., 30 figs., 5 tabs.

  4. Experimental consideration on the contact resistance caused by the distribution of contact spots with the contact model using electrolyte bath; Denkai yokuso wo mochiita sesshoku model ni yoru sesshokuten no bunpu to sesshoku teiko tokusei ni kansuru jikkenteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Aichi, H. [Daido Institute of Technology, Aichi (Japan); Miyachi, I. [Aichi Institute of Technology, Aichi (Japan)

    1996-09-20

    Electric contact members are classified by the form such as a point, a line, and a plane. Particularly, the point contact member which makes a small circular contact spot is basis of the contact form. Also, the plane contact member will make many contact spots which are different in size and distributing over the contacting portion. Authors have been developing the contact model to measure the contact resistance. In this model, it is available to select the size, the number, and the arrangement of contact spots by the macroscopical contact spots which are formed with some metal electrodes arranged in electrolyte solution of dilute sulfuric acid. In this paper, the fundamental characteristics of the contact resistance caused by the construction of current are investigated with 1 to 3 contact spot models. Then the relations between the contact resistance and the distribution of the contact spots are examined with 2 to 9 multi-contact spot models. As the results, it is cleared that the proposed contact model presents the successful experimental method for the analysis of the contact resistance. 9 refs., 8 tabs.

  5. Numerical calculation of gas and liquid velocities along a vertical flat plate immersed in turbulent tow-phase bubbly flow. Kihoryuchu ni okareta suichoku heiban mawari no ranryu kieki 2 soryu ni kansuru suchi kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Matsuura, A.; Nakamura, H. (Daido Inst. of Technology, Nagoya (Japan)); Hiraoka, S.; Tada, Y.; Kato, Y. (Nagoya Inst. of Tech. (Japan))

    1993-11-10

    A numerical calculation was made on the bubbly flow using the Prandtl's mixing length theory. The calculation results agreed well with the experimental results in the turbulent flow rather than in the laminar flow. The necessity of discussion on the turbulent flow analysis was clarified. It was elucidated that the experimental results could be explained sufficiently even by the simplest mixing model. The liquid phase velocity vector was aligned on the same direction when the bubbly flow length exceeded 1 cm, and little change took place in the velocity distribution shape. In the analysis of laminar flow, the velocity boundary layer was developed together with tie bubbly flow length, while in the analysis of turbulent flow, such change did not take place. The liquid phase velocity in the vicinity of the inlet had a velocity component which directed to the outside of the wall at the wall side. It was quite different from the analytical result of the laminar flow. The gas phase velocity vector behaved in the similar way to the liquid phase. The velocity direction at the periphery of the velocity distribution in the vicinity of tie inlet was toward the wall surface, and the inlet velocity was rapidly accelerated. 12 refs., 4 figs.

  6. Experiments on the injection of a circular jet into a wake of an airfoil. Mean flow properties; Tsubasa no koryuchu ni fukidasareru enkei funryu ni kansuru jikken. Heikinryu no tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, H.; Komori, N. [Daido Institute of Technology, Nagoya (Japan); Nakamura, I. [Nagoya University, Nagoya (Japan). Faculty of Engineering

    1995-01-25

    This paper reports the result obtained when a circular jet was injected into a wake of a two-dimensional symmetrical airfoil in a uniform air current and when the three-dimensional mixing process in the jet was examined. In these experiments, the attack angle ({alpha}) of the airfoil was set to 0{degree} and 5{degree}, and the circular jet was injected from near the trailing edge of the airfoil to the airfoil surface. The relative velocity distribution of the mean jet velocity to the wake is axisymmetric and almost coincides with the Gaussian distribution (reported by Mr. Ishigaki) for a two-dimensional free jet. The maximum relative velocity of the jet and the state of attenuation vary depending on the ambient wake field. In relative velocity distribution, the half-value width in the Y direction (perpendicular to the uniform flow direction and airfoil width direction) and Z direction (perpendicular to the uniform flow direction and Y direction) has hardly any difference when {alpha} is 0{degree}. The half-value width in the Z direction is slightly higher than that in the Y direction when {alpha} is 5{degree}. In this case, the jet is extended near the center in the Z direction. 15 refs., 14 figs.

  7. Investigations and researches on CO2 balance in a high-temperature carbon dioxide separation technology; Nisanka tanso koon bunri gijutsu ni okeru CO2 balance ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to select a promising process by comparing application environments and effectiveness of a high-temperature carbon dioxide separation, recovery and re-utilization technology with other methods, investigations were performed on reducible amount of carbon dioxide discharge by using material balance and system introduction. A large number of chemical and physical technologies are being developed for the separation and refining methods. This paper discusses the technologies for their application to iron and steel making, oil refining, and petrochemical industries, the so-called heavy and large product industries. As a possibility of utilizing the high-temperature separated CO2 in iron and steel making, an investigation was given on the direct iron ore smelting reduction process. It would be unreasonable to use CO2 in oil refining as a substitute to air to regenerate a catalytic decomposition and reformation catalyst because of decline in the catalytic activity. A discussion was given on a case to replace steam with CO2 in steam reformation and pyrolysis of hydrocarbons. The discussion requires the objective to be focused on such items as C/H ratio at a reformer outlet and relationship of balance in decomposition products. The C1 chemical and others were reviewed to search possibilities for their use as raw materials of chemicals used in chemical industries. Possibilities were discussed to fix high-temperature CO2 into peridotite and serpentine. 42 refs., 32 figs., 11 tabs.

  8. Seismic tomography inversion in the case that sources and receivers are distributed out of a 2-D plane; Shingen jushinten ga nijigen heimennai ni nai baai no danseiha tomography kaiseki ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yokota, T.; Miyazaki, T. [Geological Survey of Japan, Tsukuba (Japan); Rokugawa, S.; Matsushima, J. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Ashida, Y. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-01

    In the case where sources and receivers are not distributed on a 2-D plane, seismic tomography inversion was studied. In tomography experiments, the existing wells are generally used. In such case, sources and receivers are frequently not distributed on a 2-D plane. The 2.5-D analysis method including 2-D structure and 3-D ray-tracing was thus developed. This method is featured by less memory necessary for ray-tracing calculation, and the same algorithm for velocity determination as 2-D analysis method. In previous methods, since analysis is generally carried out by projecting sources and receivers on a certain assumed 2-D plane, it can derive correct results in the case of constant velocity and straight ray, however, in the other case, it derives incorrect results. Application of 3-D tomography requires a large amount of memory, and falls into poor convergence because of various parameters. The 2.5-D analysis method can avoid these demerits. This analysis method was applied to the data obtained in Ogiri area, Kagoshima prefecture. 5 refs., 3 figs., 2 tabs.

  9. Computer simulation analysis on EEVC pedestrian subsystem impact test. Evaluation of impact energy in upper legform test; EEVC hokosha hogo shikenhoan ni kansuru computer simulation kaiseki. Daitaibu shikenhoan de teiansareta shototsu energy no datosei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Konosu, A.; Ishikawa, H. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

    1999-11-01

    EEVC upper legform test conditions are determined exclusively from car-front shapes, bonnet leading edge (LEH) and bumper lead (BL), without considering car-front stiffness. However, the car-front stiffness may affect the test conditions significantly. Furthermore, it seems that the EEVC test condition was obtained from computer simulation using a dummy-like pedestrian model, instead of a human-like pedestrian model. Our computer simulation results indicated that car-front-stiffness varied impact energy 300 J at maximum, and impact energy obtained using the dummy-like pedestrian model was 93 to 384 J higher as compared to those obtained from the human-like pedestrian model. In order to evaluate vehicle safety performance in car-pedestrian accidents appropriately, the current EEVC impact energy curve of upper legform test should be reconsidered. (author)

  10. Fiscal 1998 research report on the development trends of natural gas conversion technologies into liquefied fuel in Russia; 1998 nendo Roshia ni okeru tennen gas no ekitai nenryoka gijutsu no kaihatsu doko nado ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Russia having natural gas resources largest in the world is actively promoting the basic research on liquefaction technology of natural gas such as Fischer-Tropsch (FT) synthetic catalyst, and its research potential is extremely high. This 3-year research project surveys the R and D trends of catalyst technology for liquefaction of natural gas, and fabricates the prototype FT synthetic catalyst based on the idea of Russian researchers to evaluate its feasibility experimentally. This report summarizes the following to clarify the research background: (1) The technology system for liquefaction of natural gas, and its future R and D trend, (2) The R and D trends of liquefaction technology of natural gas in the world, (3) The R and D trends of liquefaction technology of natural gas in Russia, (4) The research system of catalyses in Russia, (5) The activities of Russian catalysis research institutes, (6) The fuel liquefaction technologies of Russian major research institutes, and (7) The proposals from Russian research institutes. (NEDO)

  11. Study on heat transport rate of an osmotic heat pipe. 2nd Report. Flow in a membrane module; Shinto heat pipe no netsuyuso ni kansuru kenkyu. 2. Maku module nai no ryudo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Ipposhi, S.; Imura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

    1998-05-25

    An osmotic heat pipe is a top beat mode heat pipe driven by an osmotic force. Therefore, a concentration and a solution flow rate in a membrane module of the osmotic heat pipe are especially of great importance for the heat transport. Thus, the flow in the membrane module is7investigated in detail. As a result, with a ratio of a concentration on the membrane wall to a mixed mean concentration derived semi-theoretically, correlations for the mixed mean concentration, the concentration on the wall and the solution flow rate along the channel in the membrane module were proposed, which can correlate the experimental data from reference (2) within {+-}20% errors. In addition, a method of increasing in the osmotic pumping rate and heat transport rate was proposed. 3 refs., 10 figs., 1 tab.

  12. Experimental study on penetration of chloride ions into concrete and corrosion of reinforcing bars in various marine environments; Shuju no kaiyo kankyo joken ni okeru concrete no enbun shinto to tekkin fushoku ni kansuru jikkenteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, N.; Sogo, S. [Obayashigumi Research Inst., Tokyo (Japan)] Sakoda, S. [Tokai Univ., Tokyo (Japan)] Idemitsu, T. [Kyushu Inst. of Tech., Kitakyushu, Fukuoka (Japan)

    1998-08-20

    Moreover the various environmental conditions in the ocean, the conditions varies with a region, the construction position of the structures, a part and so on. Therefore, it makes difficult to grasp the effects of the difference of environmental conditions on the penetration rate of salinity and the advance of corrosion in reinforcing bars. In this study, exposure tests of concrete in marine environments were conducted over a period ten years to establish the rational design considered durability of concrete structures. In this tests, penetration of chloride ions, corrosion of reinforcing bar and quality change of concrete were investigated. As a result, chloride ion distribution can be predicted by using the chloride ion diffusion coefficient (Dc) and surface chloride ion density (Co) obtained from exposure tests. It was clarified that the rate of chloride ion penetration in marine environments is fastest in the splash zone, followed by submerged and atmospheric zones and so forth. 20 refs., 31 figs., 7 tabs.

  13. Study on heat transport rate of an osmotic heat pipe. Effects of the initial concentration on the heat transport limits; Shinto heat pipe no netsu yuso ni kansuru kenkyu. 1. Shoki nodo no netsu yuso genkai ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Ipposhi, S.; Imura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering

    1998-01-25

    This paper describes an experimental study on. the effects of an initial concentration on a maximum heat transport rate of an osmotic heat pipe operated under the atmospheric pressure. The working fluid was aqueous polyethylene glycol 600 solution and the 18 tubular-type osmosis membranes made of acetyl cellulose were used. The initial concentration was varied from 0.1 to 1.0 kmol/ m{sup 3} with 0.1 kmol/m{sup 3} step. As a result, it is shown that the optimum initial concentration exists for the maximum heat transport rate in the osmotic heat pipe. In addition, the concentrations in the solution riser and downcomer are related to the initial concentration. 11 refs., 11 figs., 2 tabs.

  14. RESISTENCIA CHIMILA: NI ANIQUILADOS, NI VENCIDOS

    Directory of Open Access Journals (Sweden)

    Edgar Rey Sinning

    2009-08-01

    Full Text Available En este artículo se examina de forma sucinta la respuesta que los Chimilas dieron al proceso de usurpación de su territorio, mostrando cómo lograron resistir y lucharon por recuperar su espacio social, al tiempo que se señalan los efectos que tuvo sobre ellos el último proceso de ocupación territorial que, con fines capitalistas, el Estado colombiano y las economías privadas llevaron a cabo, pese al cual no fueron “ni aniquilados ni vencidos”. Finalizaremos este artículo señalando las características de las últimas fundaciones en territorio Chimila y su lucha por la supervivencia. Para su elaboración se reunió una variada información, a partir de diversos documentos históricos recolectados en archivos nacionales y regionales, diarios, cartas y crónicas de viajeros, además de las diversas reflexiones que han elaborado, antropólogos, sociólogos e historiadores sobre la temática.

  15. and ni(ii)

    African Journals Online (AJOL)

    userpc

    with nickel(II) and cobalt(II) chloride in 2:1 mole ratio yielded Ni(II) and Co(II) complexes respectively. The synthesized compounds were characterized based on melting point/decomposition temperature, solubility, molar conductance, magnetic susceptibility and infrared spectral analyses. The complexes have low molar ...

  16. SOVRAŽNI GOVOR

    OpenAIRE

    Ajtnik, Mojca

    2015-01-01

    Pojem sovražnega govora izhaja iz anglosaškega sveta in temelji na prepričanju o manjvrednosti nekaterih ljudi, zaradi njihove pripadnosti določeni skupini. Sovražni govor je eden ključnih trenutkov v vzbujanju sovraštva do določenih skupin ljudi. Takšen govor je neizogibno povezan s predsodki, diskriminacijo in stereotipi. Je stalni spremljevalec človeške družbe, vedno večja prisotnost sovražnega govora v današnji družbi pa je posledica potrošniško in kapitalistično naravnane družbe. Na pora...

  17. Ni landsbyer i Danmark

    DEFF Research Database (Denmark)

    Larsen, Jacob Norvig

    Denne rapport beskriver en evaluering af statsstøttede forsøg med at styrke og udvikle mindre lokalsamfund. Forsøgene er gennemført i ni kommuner. Da der i disse år er stor opmærksomhed om de små byers og samfunds udviklingsmuligheder, har erfaringerne fra forsøgsprojekterne bred interesse. Forsø...

  18. Submicron particles of Co, Ni and Co–Ni alloys

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 24; Issue 5 ... Magnetic Materials Volume 24 Issue 5 October 2001 pp 515-521 ... Magnetic sub-micron sized particles (with diameters in the range 100–600 nm) of Co, Ni and Co–Ni alloys, protected with polyvinylpyrrolidone have been prepared in gram quantities ...

  19. Niños investigadores

    Directory of Open Access Journals (Sweden)

    Manfred Liebel

    2007-12-01

    Full Text Available EN LA SOCIOLOGÍA INFANTIL, EL PRINCIPIO DE HACER PARTICIPAR A NIÑAS Y NIÑOS en los procesos de investigación está ampliamente reconocido. Tomando como punto de partida ese principio de participación, el presente aporte analiza la pregunta de en qué medida y de qué manera los niños mismos pueden actuar como investigadores. A fin de apreciar en lo justo la perspectiva de los niños, el presente trabajo aboga por que –con el debido acompañamiento de personas adultas– la investigación esté en manos de los niños. Por medio de varios ejemplos de países del Sur, se muestra cómo poner en práctica esta forma de investigación encabezada por niños. Tomando en cuenta la desigualdad en las relaciones entre niñas, niños y personas adultas, el trabajo hace referencia a problemas de ética y práctica investigativa que surgen en el proceso de investigación y también en el tema del uso de los resultados. Finalmente, se explican los beneficios que niñas y niños pueden obtener de sus propias investigaciones.

  20. Oxidation behavior of Ni powder and Ni powder compact; Ni fun oyobi Ni fun atsufuntai no sanka kyodo

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, M.; Ochiai, S.; Watanabe, Y. [Teikyo Univ., Tokyo (Japan)

    1997-09-15

    With an objective to investigate reactions of metal powder and metal powder compact having open pores with gases, their oxidation behavior was elucidated by taking Ni powder and Ni powder compact as examples. Oxidation rate of the Ni powder can be expressed by the Jander equation, and activation energy for the oxidation was 0.948 times 10 {sup 5} J/mol. Oxidation rate of the Ni powder compact is equal to that of powder not made into compact in the initial stage of the oxidation, but it decreases as time elapses because of occurrence of packing of oxide. Difference in oxidation rate inside and outside the powder compact is very little. The oxidation rate of the powder compact was analyzed by using an improved Jander model. More specifically, a model was used, in which concentration difference of diffused components in the oxides decreases with progress of the oxidation, whereas 1.113 times 10 {sup 5} J/mol was derived as the activation energy of the oxidation. The cause for the activation energy for the oxidation of the powder and powder compact being about half of that for bulk Ni is because of low temperature oxidation of the powder, and tensile stress generated between metal particles and spherical shell shaped oxides, which make production of Ni {sup 2+} more difficult. 5 refs., 4 figs., 1 tab.

  1. Nitriding behavior of Ni and Ni-based binary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Fonovic, Matej

    2015-01-15

    Gaseous nitriding is a prominent thermochemical surface treatment process which can improve various properties of metallic materials such as mechanical, tribological and/or corrosion properties. This process is predominantly performed by applying NH{sub 3}+H{sub 2} containing gas atmospheres serving as the nitrogen donating medium at temperatures between 673 K and 873 K (400 C and 600 C). NH{sub 3} decomposes at the surface of the metallic specimen and nitrogen diffuses into the surface adjacent region of the specimen whereas hydrogen remains in the gas atmosphere. One of the most important parameters characterizing a gaseous nitriding process is the so-called nitriding potential (r{sub N}) which determines the chemical potential of nitrogen provided by the gas phase. The nitriding potential is defined as r{sub N} = p{sub NH{sub 3}}/p{sub H{sub 2}{sup 3/2}} where p{sub NH{sub 3}} and p{sub H{sub 2}} are the partial pressures of the NH{sub 3} and H{sub 2} in the nitriding atmosphere. In contrast with nitriding of α-Fe where the nitriding potential is usually in the range between 0.01 and 1 atm{sup -1/2}, nitriding of Ni and Ni-based alloys requires employing nitriding potentials higher than 100 atm{sup -1/2} and even up to ∞ (nitriding in pure NH{sub 3} atmosphere). This behavior is compatible with decreased thermodynamic stability of the 3d-metal nitrides with increasing atomic number. Depending on the nitriding conditions (temperature, nitriding potential and treatment time), different phases are formed at the surface of the Ni-based alloys. By applying very high nitriding potential, formation of hexagonal Ni{sub 3}N at the surface of the specimen (known as external nitriding) leads to the development of a compound layer, which may improve tribological properties. Underneath the Ni{sub 3}N compound layer, two possibilities exist: (i) alloying element precipitation within the nitrided zone (known as internal nitriding) and/or (ii) development of metastable and

  2. Abnormal Intermetallic Compound Evolution in Ni/Sn/Ni and Ni/Sn-9Zn/Ni Micro Solder Joints Under Thermomigration

    Science.gov (United States)

    Zhao, N.; Deng, J. F.; Zhong, Y.; Huang, M. L.; Ma, H. T.

    2017-04-01

    Interfacial reactions in Ni/Sn/Ni and Ni/Sn-9Zn/Ni micro solder joints during thermomigration (TM) have been studied by reflowing solder joints on a hot plate. Asymmetrical growth and transformation of interfacial intermetallic compounds (IMCs) were clearly observed. The growth of the Ni3Sn4 IMC in the Ni/Sn/Ni solder joints was always fast at the cold end and relatively slow at the hot end. Only asymmetrical growth of the Ni5Zn21 IMC in the Ni/Sn-9Zn/Ni solder joints occurred at the beginning because Zn was the dominant TM species; however, asymmetrical transformation of the Ni5Zn21 IMC also occurred under the combined effect of Zn depletion and Ni dissolution and migration, resulting in formation of a thin τ-phase layer at the hot end and a thick τ-phase/Ni5Zn21/τ-phase sandwich structure at the cold end. TM of Ni and Zn atoms was identified towards the cold end, being responsible for the abnormal IMC evolution. Addition of Zn was found to slow the TM-induced IMC growth and Ni dissolution.

  3. Electronic structure of Ni/sub 3/Al and Ni/sub 3/Ga alloys

    CERN Document Server

    Pong, W F; Chang, Y K; Tsai, M H; Hsieh, H H; Pieh, J Y; Tseng, P K; Lee, J F; Hsu, L S

    1999-01-01

    This work investigates the charge transfer and Al(Ga) p-Ni d hybridization effects in the intermetallic Ni/sub 3/Al(Ni/sub 3/Ga) alloy using the NiL/sub 3.2/- and K-edge and Al(Ga)K X-ray absorption near edge structure (XANES) measurements. We find that the intensity of white-line features at the NiL/sub 3.2/-edge in the Ni/sub 3/Al(Ni /sub 3/Ga) alloy decreased in comparison with that of pure Ni, which can be attributed to the enhancement of Ni3d states filling and the depletion of the density of Ni 3d unoccupied states in the Ni/sub 3 /Al(Ni/sub 3/Ga) alloy. Two clear features are also observed in the Ni/sub 3/Al(Ni/sub 3/Ga) XANES spectrum at the Al(Ga) K-edge, which can be assigned to the Al(Ga) unoccupied 3p (4p) states and their hybridized states with the Ni 3d/4sp states above the Fermi level in Ni/sub 3/Al(Ni/sub 3/Ga). The threshold at Al K-edge XANES for Ni/sub 3/Al clearly shifts towards higher photon energies relative to that of pure Al, indicating that Al loses charges upon forming Ni/sub 3 /Al. ...

  4. Measurement of 59Ni and 63Ni by accelerator mass spectrometry at CIAE

    Science.gov (United States)

    Wang, Xiaoming; He, Ming; Ruan, Xiangdong; Xu, Yongning; Shen, Hongtao; Du, Liang; Xiao, Caijin; Dong, Kejun; Jiang, Shan; Yang, Xuran; Lan, Xiaoxi; Wu, Shaoyong; Zhao, Qingzhang; Cai, Li; Pang, Fangfang

    2015-10-01

    The long lived isotopes 59Ni and 63Ni can be used in many areas such as radioactive waste management, neutron dosimetry, cosmic radiation study, and so on. Based on the large accelerator and a big Q3D magnetic spectrometer, the measurement method for 59Ni and 63Ni is under development at the AMS facility at China Institute of Atomic Energy (CIAE). By using the ΔE-Q3D technique with the Q3D magnetic spectrometer, the isobaric interferences were greatly reduced in the measurements of 59Ni and 63Ni. A four anode gas ionization chamber was then used to further identify isobars. With these techniques, the abundance sensitivities of 59Ni and 63Ni measurements are determined as 59Ni/Ni = 1 × 10-13 and 63Ni/Ni = 2 × 10-12, respectively.

  5. Accident reconstruction to analyze impact of injured drivers during the collision. Ankle fracture in the car-to-car offset frontal collision; Join no jusho jokyo ni kansuru jiko saigen. Joyosha doshi no offset zenmen shototsuji no ashi kansetsu kossetsu

    Energy Technology Data Exchange (ETDEWEB)

    Sakurai, M. [Japan Automobile Research Institute Inc., Tsukuba (Japan)

    1997-10-01

    An accident reconstruction test of car-to-car crash was conducted in order to analyze the impact on the driver in the offset head-on collision. The ankle fracture of the driver resulting from the accident was examined with the test results and the accident data. The test results of the car-to-car crashes indicated that the belted driver`s ankle would have fractured in the early stage of the crash. The detailed information from the accident data, especially the cars` interior deformation and the driver`s X-ray photographs, was also very important in analyzing injury mechanisms of the ankle/foot region. The above results suggested an injury mechanism that the ankle joint fracture was due to dorsiflexion and valgus resulting from the impact and intrusion of the toeboard in the early stage of the crash. 12 refs., 11 figs.

  6. Interim report on the research development of high combustion technology using the microgravity environment; Bisho juryoku kankyo wo riyoshita kodo nensho gijutsu soshutsu ni kansuru kenkyu kaihatsu chukan hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    There are problems on diversification of energy from a viewpoint of energy stabilized supply and reduction of environmental pollutant in fuel exhaust gas. For the solution, combustion phenomena are elucidated using microgravity equipment, and a combustor which enables high combustion technology is studied. For it, a field survey is conducted on implementation of international joint research with the U.S.` NASA, and at the same time experiments and analyses of the experimental data are carried out using microgravity experimental equipment. For experiments using microgravity experimental equipment and analysis/evaluation of experimental data, the following were conducted: (1) evaluation of combustion properties of various fuels, (2) fabrication of equipment needed for experiments for analysis/evaluation of combustion parameters, and combustion/evaporation evaluation experiments of fuel droplet/droplet group using microgravity experimental equipment, evaluation experiment to elucidate combustion property of solid particle mixed fuel, evaluation experiment of combustion limit, etc. In fiscal 1993, experimental data are being acquired for establishing a target experimental method. 42 refs., 151 figs., 1 tab.

  7. Fiscal 1998 research report on the basic research on the practical application of innovative technologies. 2; 1998 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report is composed of the part 1 'Estimation of fossil energy resources and preliminary preparation of the super- long-term view of energy supply and demand', and the part 2 'Research on concrete conditions for introducing renewable energy (RES)'. In the part 1, estimation was made on the amount of non-conventional fossil energy resources such as oil sand, oil shale, coal bed methane and methane hydrate. Study was also made on the role of nuclear power, fast breeder reactor and nuclear fusion in the world energy supply and demand in the 21st century. In addition, as preliminary study on the super-long-term view of energy supply and demand in the next fiscal year, study was made on a scenario and measuring model considering energy supply restriction and CO{sub 2} problem. In the part 2, research was made on the amount of resources, applicable fields and cost estimation for various RESs such as solar energy, wind power, biomass, oceanic energy, geothermal energy and hydraulic power. Several technical issues on transport, storage, conversion and use for every energy were arranged toward real introduction, efficient use and stable supply of such RESs. (NEDO)

  8. Achievement report for fiscal 1997 on investigative research on society compatibility of development of coal hydrogasification technology; 1997 nendo sekitan suiso tenka gas ka gijutsu kaihatsu shakai tekigosei ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In view of possibility of the future tightness in natural gas supply, establishment of coal gasification technology was set as the final objective, which can supply cheaply and stably the substitution natural gas of high quality by using coal existing affluently over the world as the raw material. An investigative research is carried out under a five-year plan on society compatibility required to assess the possibility of the practical application thereof. Fiscal 1997 has performed in continuation from the previous year the 'survey on process level elevation' and 'survey on the society compatibility'. This report summarizes the achievements thereon. In the investigative research on the process level elevation, the Shell's methane synthesis process based on an oxygen blown and dry feed coal gasifier was evaluated, and the calculation process was pursued on material balance in a hydrogasification reactor as having been performed in the 'survey on developing the coal hydrogasification technology' in which its reasonability was verified. In the survey on the society compatibility of the process, a survey was carried out on natural gas (including non-conventional methane hydrate and coal bed methane) and coals as raw materials for hydrogasification. (NEDO)

  9. Fiscal 2000 technical trend survey report on the surveys of technical trends regarding development of microminiature high-density power source technology; 2000 nendo chokogata komitsudo power gen gijutsu no kaihatsu ni kansuru gijutsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys are conducted of technical trends of, and needs for, versatile microminiature high-density power sources, and research and development projects are proposed for micro fuel cells, combustion type micro power generation, environmental micro power generation, and micro rockets. Assumed in the research and development of micro fuel cells are a direct methanol method, chemical hydride method, micro combustion reformer method, and a hydrogen method using advanced hydrogen absorbing materials. Assumed in the research and development of combustion type micro power generators are a micro engine power generator (gas turbine power generation, steam cycle power generation), thermophotovoltaic micro power generator, catalyst-aided combustion thermophotovoltaic micro power generator, and so forth. Assumed in the research and development of environmental micro power generators are an environmental micro vibration power generator, environmental micro thermal power generator, environmental electromagnetic power generator, non-contact power feeding system, and so forth. Assumed in the research and development of micro rockets are a solid micro rocket array, micro PPT (pulsed plasma thruster), card type electric propulsion system, and so forth. (NEDO)

  10. Studies of technology of mass production and quality control in road base material using coal ash; Sekitanbai wo genryo to suru robanzai no ryosan hinshitsu kanri gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, Y. [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Ozasa, K. [Center for Coal Utilization, Tokyo (Japan); Tsuzura, K. [Naruto Salt Mfg. Ltd., Tokushima (Japan); Izumi, H. [Nippon Hodo Co. Ltd., Tokyo (Japan)

    1998-05-10

    Use of granular solidified coal ash as a road base material has been studied to facilitate the large scale utilization of powdered material. The proposed technology of producing granular solidified coal ash includes steam curing combined with different unit operations. Investigations on the technological and quality control aspects make clear the followings: (1) A proper technology for large scale processing may consists of the following steps: kneading of coal ash with water around its plastic limit, low pressure molding, steam curing and crushing. (2) A road base material of good quality can be produced in large qualities from coal ash of fixed CaO content and unburnt carbon content. Further processing includes mixing with the amount of water based on the size and the time change degree of the consuming power in kneader, kneading and molding. The temperature of the kneading water should be adjusted to the ambient conditions. 4 refs., 7 figs., 3 tabs.

  11. FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

  12. Study of reaction and heat release from solid combustion in strong magnetic field; Kyojiba wo riyoshita hikinshitsu kotai nensho shori no hanno to netsu no seigy ni kansuru kiso kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, K.; Fujita, O.; Iiya, M.; Kudo, K. [Hokkaido University, Sapporo (Japan)

    1997-02-01

    To establish the inhomogeneous solid combustion control technology, effects of the strong magnetic field on the solid combustion were examined. When applying the sufficiently strong magnetic field, it is possible to control the air flow in combustion field by utilizing the force applying to constituent oxygen with large susceptibility. Based on this possibility, combustion experiments of expanded polystyrene plates were conducted between the magnetic poles of electro-magnet having the maximum flux density of 1 T and the maximum magnetic field gradient of 0.5 T/cm. To observe the effects of magnetic field without the effects of natural convection, combustion experiments of acrylic sheets were conducted between the magnetic poles of electro-magnet having the maximum flux density of 0.6 T and the magnetic field gradient of about 0.1 T/cm under the microgravity conditions between 10{sup -4} and 10{sup -5}g using a microgravity test facility. Consequently, prospective combustion results could be obtained, in which the force of flame received from the magnetic field is almost equivalent to the buoyancy of flame. It was demonstrated that combustion can be controlled by the magnetic field. 1 ref., 3 figs., 1 tab.

  13. Study of thermodynamic properties of HFC refrigerant mixtures for Loretz-cycled niew generation air-conditioning equipment; Lorentz cycle ka shinsedai kucho kikiyo HFC kei kongo reibai no netsu rikigaku seishitsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, K.; Sato, H. [Keio University, Tokyo (Japan). Faculty of Science and Technology

    1997-02-01

    This paper describes thermodynamic properties of HFC refrigerant mixtures for Lorentz-cycled new generation air-conditioning equipment. Equipment has been completed for simultaneous measurement of density and vapor-liquid equilibrium property, accurate measurement of latent heat of vaporization, and accurate measurement of specific heat at constant pressure in liquid phase. Final adjustment and preliminary measurements are currently conducted. Through analytical investigation using actually measured data of thermodynamic properties of HFC refrigerant mixtures, five state equations were obtained, i.e., modified Peng-Robinson state equation which can reproduce the vapor-liquid equilibrium property of refrigerant mixtures, modified Patel-Teja state equation, Helmholtz function type state equation which is applicable in the whole fluid region of refrigerant mixtures, and so on. An evaluation test equipment has been fabricated as a trial for Lorentz-cycled air-conditioning equipments using HFC refrigerant mixtures, and demonstration test is conducted to confirm the validity. 9 refs., 5 figs.

  14. Introduction of report of the investigation into deflagration and fire accident (1992) at a British Corporation, Hickson and Welch Co. Ltd.; Eikoku HICKSON and WELCH sha no bakunen kasai jiko (1992 nen) ni kansuru chosa hokokusho no shokai

    Energy Technology Data Exchange (ETDEWEB)

    Sato, K. [The High Pressure Gas Safefy Institute of Japan, Tokyo (Japan)

    1995-09-01

    A deflagration and fire accident broke out at Hickson and Welch Co., Ltd., Castleford, West Yorkshire, England at two p.m. September 21, 1992, and five persons were killed, 14 persons were injured, and the factory facilities were also seriously damaged. This article summarizes the accident based on the final report recently issued by the Health and Safety Executive (HSE) of Britain. This accident broke out during operation for removing sludge accumulating in a still for separating and purifying process positioned on the downstream side of a nitrotoluene production plant in the Hickson Co., Ltd.`s factory. Ignoring manager`s individual responsibility, the HSE used the company for its general management mistake. In regard to this, the court judged that Hickson Co., Ltd. must pay a penalty of 250 thousand pounds for violating general duty items for protection of the health and safety of the employees and also pay for the investigating costs of 150 thousand pounds incurred by the HSE. 2 refs., 2 figs.

  15. Study on the selection of steel or prestressed concrete cable stayed bridge by using diaggregate behavioral model; Hishukei rojitto model wo mochiita koshachokyo to PC shachokyo no kyoshiki sentaku ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Araki, Y.; Furuta, H.; Maeda, E.; Furukawa, K. [Yamaguchi University, Yamaguchi (Japan). Faculty of Engineering

    1994-09-15

    A discussion was given to make clear the selection factors in selecting bridge types (steel cable stayed bridge and prestressed concrete cable stayed bridge). The discussion is intended to consider the future development of both bridges. Quoting a cable stayed bridge with a span length of 250 m that can be selected from either bridge, an evaluation was made by using calculations that uses the disaggregate behavioral model theory based on questionnaire responses from engineers. The analysis uses the following procedure: utility function values of the two term behavioral model (having two choices) are specified and the characteristics variables are selected; the data are prepared according to the specifications, which are used to estimate parameters by a maximum likelihood estimation method; and estimation amount is estimated by using the covariance matrix, which is given a `t` value verification. The conclusions: what gives the large effect to the selection is the engineering capacity and sociality; the result contains vocational consciousness; the economy is measured by the large weight of construction cost for the upper part structures and cost required for large repairs; materials affect largely the reliability, and so does the technological level the constructibility; the comprehensive technical capability, freedom in design and the experience attained by Japan have great effects in terms of technological capability. 10 refs., 10 figs., 11 tabs.

  16. Some considerations on special spacers with damping device for suppressing wake galloping in tandem cables of cable-stayed bridges; Heiretsu cable yo gensui kino tsuki supesa no gensui fuka tokusei ni kansuru 2,3 no kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yoneda, M. [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology] Setouchi, H. [Kawada Industries Inc., Osaka (Japan)

    1998-03-20

    Cable vibration called wake galloping appears on cable-stayed bridges with parallel arranged cables and its suppression is an important problem. Various methods have been proposed for spacers with damping device for suppressing wake galloping in tandem cables of cable-stayed bridges. But, comparison of damping performances of various methods have not been discussed sufficiently. This paper deals with a type in which dampers are equipped on the midway of the tandem cables through the spacer jig and a type in which dampers are equipped on each surface of the tandem cables to generate shear deformation between them and circular spacer jig moiety and complex eigenvalue analyses are carried out on the two types with changing center spacing and diameters of the cables. The results clarify the relation between the structural damping characteristics and the cable spacing and the effect of torsional rigidity of the cables and also clarify of damping characteristics of the two types. 16 refs., 14 figs., 4 tabs.

  17. Study on the ultra-high speed LAN corresponding to the ultra-high speed IP network of Kansai Electric Power Co.; LAN no chokosokuka ni kansuru kenkyu. Tosha IP network no chokosokuka eno taio hoho

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, R. [Kansai Electaric Power Co. Inc., Osaka (Japan)

    2000-04-01

    This study was made on survey and evaluation of high-speed network technology and routing protocol based on IP (Internet protocol) network. This paper outlines the evaluation result, and explains the performance verification test result on the routing protocol OSPF (open shortest pass fast) used for the IP network of Kansai Electric Power Co. High-speed LAN using Giga-Bit Ethernet instead of Ethernet was confirmed to be more profitable than ATM-LAN from the viewpoint of cost reduction, operation control, and affinity with the existing IP network. POS (packet over synchronous digital hierarchy) system was adopted as high-speed WAN (wide area network) from the viewpoint of cost reduction, and affinity with the existing IP network. OSPF system was adopted as routing protocol for the next-generation IP network because of its affinity with loop type topology and shorter circuit switching time. The verification test result of OSPF showed such features as short circuit switching time, optimization of a communication route by selecting the widest-band route, and flexible modification of topology. (NEDO)

  18. Fiscal 1998 research report. Research on the possibility of promoting CDM project through technology transfer with plant exports; 1998 nendo chosa hokokusho. Plant yushutsugata gijutsu iten wo tsujita CDM project suishin kanosei ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on promotion of CDM (clean development mechanism) project through technology transfer with plant exports. Although CDM system was provided in COP3 on climate change held in Kyoto in 1997, its detailed rules including project approval are yet undecided, and only the schedule to provide the detailed rules until COP6 in 2000 was decided in COP4 in 1998. The common recognition that the CDM project with plant exports produces various merits for both Japan and the partner country is increasing. However, from the viewpoint of forming concrete CDM projects, most Japanese enterprises are passive in approach to the CDM project because of no detailed design of CDM, uncertain profitability and procedures, and avoidance of additional burdens. Plant export is also difficult because of the fact that assessment of a new project is difficult. Enterprises' deeper recognition on the CDM project, and a governmental integrated support system are desirable. (NEDO)

  19. Study on the change of aspect ratios of small surface cracks emanated from a toe of corner boxing; Mawashi yosetsudome tanbu kara hassei denpasuru bishi bisho hyomen kiretsu no aspect hi henka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Toyosada, M.; Yamaguchi, K.; Takeda, K.; Watanabe, Y. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

    1997-10-01

    The fatigue test of specimens with a stiffener was carried out to examine the change in aspect ratio (crack depth/length) of fatigue cracks in a stress concentration field and residual stress field. The aspect ratio of surface cracks just after generation can be represented with the single virtual surface crack with the same value as K value at the deepest point considering an interference effect from near cracks. No discontinuous change in K value is found at the deepest point even during growth and combination of cracks on a surface. The change in K value at the deepest point is thus the criterion to represent growth and combination of surface cracks considering the interference effect. The change in aspect ratio of the typical single virtual surface crack linearly decreases with an increase in crack depth. The shape of surface cracks generating and growing in a residual stress field is more flat than that in no residual stress field. In addition, in a residual stress field, surface cracks are longer at the same crack depth, and fatigue lives are shorter. 7 refs., 12 figs.

  20. Study on practical application of a longitudinal hull strength theory considering camber in cross section; Yokodanmen no sori wo koryoshita sentai tate kyodo riron no jitsuyoka ni kansuru kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    Nose, M.; Suzuki, K.; Furuno, H. [Nagasaki Institute of Applied Science, Nagasaki (Japan); Suzuki, K.

    1997-10-01

    Discussions were given on practical application of a stress analyzing method for thin-wall deformed cross-sectional beam considering cross section camber in longitudinal bending. The non-static calculation method described in the previous report can be applied to a box-type cross section having multi-connected cells, bulk cargo transport vessels and container ships with dual hull structure, and oil tankers with dual hull structure of medium size. The calculation method was capable of achieving remarkable enhancement in efficiency over that of conventional calculation methods. The present study is intended to make the method applicable also to multi-connected cross section shapes having more than one longitudinal partitions as used in dual hull VLCC and ULCC. As a result, an expanded non-static calculation system was developed, which has introduced into the conception described in the previous report a new conception of triple point and independent start point members. As a result of applying the method to dual hull bulk cargo transport vessels, container ships, dual hull oil tankers of medium size, VLCC and ULCC, it was verified that the system operated properly. Remarkable efficiency improvement has been made possible as compared with conventional analysis methods applied to individual ships. The system is capable of automatic calculation, and makes possible the practical application of the hull strength theory considering cross section camber. 3 refs., 10 figs., 1 tab.

  1. Fiscal 2000 research report on the energy consumption survey for popularizing stationary fuel cell systems; 2000 nendo teichiyo nenryo denchi no fukyu wo mokutekito shita energy no shohi ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A survey was conducted about the current state of domestic energy consumption for studying the feasibility of a stationary energy system using the polymer electrolyte fuel cell. A study relative to domestic energy consumption dealt with transition in the energy consumption rate, dependence on locality, and the effect of the makeup of residences. The monthly and hourly patterns of demand for heat for hot-water supply were referred to power consumption data broken down by time zone, and it was found that approximately 1kW output would be suitable for this purpose. A study was made about the pattern of operation that such a fuel cell system should follow, and it was learned that a pattern in which 'the system operates according to the imposed load starting at seven o'clock in the morning when the electricity rate switches to the higher and the output does not exceed what is necessary to meet the daily demand for heat.' This method was found to assure the most efficient way of operation covering more than 80% of the need for hot water and electricity. In a study of consumption of energy for business, feasibility was suggested to exist in the installation of systems of 30kW or less at small hotels, barber shops and beauty parlors, restaurants, schools equipped with minor-scale food service, small hospitals, clinics, and the like. (NEDO)

  2. Fiscal 1997 report on the survey project on planning to execute `The New Earth 21`; 1997 nendo chosa hokokusho (`chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Japan proposed in the Houston Summit the New Earth 21 to be carried out with technology development and technology transfer, and to make a concrete development of the project, Japan also proposed in the Tokyo Summit a TREE Plan for working out comprehensive strategies of the innovative technology development. In the CO3 Kyoto Conference in 1997, numerical targets for developed countries were determined which have legal binding force for control/reduction of greenhouse gas emissions in the term of 2008-2012. It was agreed to urge developing countries also to play a certain part in the project through the clean development. Therefore, the paper made quantitative analysis of important CO2 prevention technologies, technology transfer costs, and economical assessment by energy conservation. As a model, the DNE 21 model was upgraded and used into which CO2 prevention technologies, energy, economy and climate changes were integrated. In fiscal 1997, the following were carried out: collection of data on important CO2 prevention technologies and systems and analytical assessment using the DNE 21 model, CO2 reduction and selection of energy technology, assessment of energy system costs, construction of the unified DNE 21 model, and opening of the international workshop. 62 refs., 98 figs., 34 tabs.

  3. Investigations on a global environment improving technology utilizing biological functions. 2. Structuring a ligno-bioprocess; Seibutsu kino wo riyoshita chikyu kankyo kaizen gijutsu ni kansuru chosa. 2. Riguno bio process no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Discussions were given to reserve global environments on reducing dependence on fossil resources and more effectively utilizing wood resources. Economically utilizable amount of wastes from lumbering factories reaches about five million tons annually. Discussions were made on a ligno-bioprocess that uses these wastes. The current quantitative production efficiency of cellulase by means of bacterial breeding is very high. A problem is production of ligninolytic enzymes, to which application of the recombinant DNA method is indispensable. Combination of steam explosion with biological decomposition or the organosolv process is an effective method for lignin decomposition. Decomposition of cellulose by using the ultra critical water method is worth noticing. With respect to hemicellulose utilization, production of cellulose derivatives, biodegradable polymers and oligosaccharides would be conceivable by means of esterification and etherification. Vanillinic acid, adhesives, resins and lignin-based polymer materials could be manufactured from lignin. Material cost for these products accounts for about 35% of the product price, thus making the lignochemicals promising commercial products. 301 refs., 71 figs., 39 tabs.

  4. Fiscal 1997 international cooperation project. Report on the results of the research on environmental harmony type combustion technology; 1997 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Out of the R and D on the environmental harmony type combustion technology, the results of the project carried out in fiscal 1997 were summed up. In the site survey, etc., visits were paid to France, Spain, Greek, Germany, the U.K. and the U.S. to have discussions and examine the trend of research on the NOx removal catalyst and catalyst combustion. In the actual R and D, the R and D were conducted on zeolite base NOx removal catalyst, oxide composite base NOx removal catalyst, alumina base NOx removal catalyst, direct decomposition type NOx removal catalyst, catalyst combustion, etc. In the R and D of the catalyst combustion, durability under high gas flow flux was examined of PdO-Pt/Ba-Al203 catalyst developed for low temperature use, which indicated that durability and low temperature activity were heightened. As high temperature use catalyst, high temperature durability was examined of the developed Pd0-La/Gd-ZrO2 catalyst, which showed that the durability was favorable. 322 refs., 261 figs., 55 tabs.

  5. Fiscal 1996 report on the investigational research on the construction of a database of physical functions; 1996 nendo chosa hokokusho (shintai kino database no kochiku ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of realizing `the affluence` sought in the Japanese economic society, the supply and preparation of products, service and environments friendly to human beings seem to be important. In the future, the development of products which are fully considered also of aged and handicapped people is more expected than the conventional manufacturing of products added with value. Especially in accordance with the rapid aging, from a viewpoint that the lowering of physical functions caused by aging has an exactly close relation with the response to products and the environment, development of the database of physical functions for the aged which is useful for the design is urgently promoted. First, the data to be supplied for database were selected. As to the selection method, the data required for database were defined by collection/analysis of the existing data, examination of the needs of enterprise designers, and analysis of daily activities. In the study of the database, the structure by which data can be effectively supplied was studied and verified by pilot database for extraction of the subjects and solution to the problems. 6 refs., 57 figs., 26 tabs.

  6. Investigation of robust control for oil hydraulic servo system. Positioning control of proportional control valve-oil hydraulic cylinder system; Denki yuatsu servo kei no robust seigyo ni kansuru kenkyu. Hireiben yuatsu culiner kei no ichi seigyo

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, Y. [Akita University, Akita (Japan). Faculty of Engineering and Resouce and Science; Nakamura, T.; Takahashi, Y. [Akita University, Akita (Japan). Faculty of System Science and Technology

    2000-03-15

    In order to eliminate the steady state tracking error, it is common to employ integral compensators in servo Systems for constant reference signals. The LQ optimization technique is extensively used for the stabilization, and the obtained feedback control system has been applied choose to an optimal servo system. However, if the dynamic response of an identical model is unequal to that of the real plant and there is disturbance to the plant, accurate control using the LQ optimization control method is difficult. In this paper, several robust control system designs for a reference model are introduced in the following and robust stability and transient behavior are considered. We propose such robust control systems based on an optimal control method that has a two-degree-of-freedom (2DOF) system. First design of the robust optimal servo system is by a 2DOF optimal control with disturbance observer. Second is designed by a 2DOF optimal control with H controller with consideration to the mixed sensitivity problem. The experiments are carried out under several conditions, and we discuss the difference of control performance by L{sub 2} norm. As a result, the 2DOF optimal control with disturbance observer has shown good control performance in the robust and stable positioning of the oil hydraulic cylinder. (author)

  7. Research cooperation project on the development of easy injection molding control technology for engineering plastics; Engineering plastic no seikei joken kan`i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In order to enhance the industries which supply assembly parts to Japan`s assembly industries in Thailand, research cooperation project on the plastic parts production technology has started. For the research cooperation, the mold design is effectively conducted using simulation technique of CAE (computer aided engineering), and an international easy injection molding control system is made using the molding support software for injection molding machines. In FY 1996, actual situations of plastic parts and assembly industries in Thailand have been investigated through the cooperation with the counterpart of Thailand. Demand and supply of engineering plastics, receive and inspection of parts, and current circumstances of molding processing makers in Thailand have been grasped. Based on the results of this investigation, proposal of basic plan, time schedule, and delivery plan of molding machines and testing equipment have been discussed, to make the basic plan. 18 refs., 4 figs., 23 tabs.

  8. Hydroelastic responses of pontoon type very large floating offshore structures. 2nd Report. Effect of the water depth and the drift forces; Pontoon gata choogata futaishiki kaiyo kozobutsu no harochu chosei oto ni kansuru kenkyu. 2. Senkai eikyo to hyoryuryoku

    Energy Technology Data Exchange (ETDEWEB)

    Maeda, H.; Miyajima, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Masuda, K.; Ikoma, T. [Nihon University, Tokyo (Japan). College of Science and Technology

    1996-12-31

    Steady-state drift force in regular waves is theoretically analyzed. It is also studied under combined external force experimentally using a two-dimensional water tank. The fluid forces are analyzed by the pressure distribution method based on the potential theory, in which the effects of water depth are taken into account to discuss the effects of elastic deformation of the floating structure on the drift characteristics of steady-state waves. The tests were carried out using a wave-making circulating water tank equipped with a wind duct to create wind, waves and tidal flow. Drift force under a combined external force by wind, wave and/or tidal flow cannot be accurately predicted by arithmetically adding these components. For predicting drift force by tidal flow, it is necessary to take into account drag force in current at the floating structure bottom as well as that in wind at the front face. Drift force by tidal flow is affected by shallowness of water, which should be taken into account for drag forces. The floating structure will be deformed along the wave face as its stiffness decreases, basically decreasing steady-state drift force. 9 refs., 14 figs.

  9. Hybrid utilization of solar energy. Part 2. Performance analyses of heating system with air hybrid collector; Taiyo energy no hybrid riyo ni kansuru kenkyu. 2. Kuki shunetsu hybrid collector wo mochiita danbo system no seino hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Yoshinaga, M.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1996-10-27

    For the effective utilization of solar energy at houses, a heating system using an air hybrid collector (capable of simultaneously performing heat collection and photovoltaic power generation). As the specimen house, a wooden house of a total floor area of 120m{sup 2} was simulated. Collected air is fanned into a crushed stone heat accumulator (capable of storing one day`s collection) or into a living room. The output of solar cell arrays is put into a heat pump (capable of handling a maximum hourly load of 36,327kJ/h) via an inverter so as to drive the fan (corresponding to average insolation on the heat collecting plate of 10.7MJ/hm{sup 2} and heat collecting efficiency of 40%), and shortage in power if any is supplied from the system interconnection. A hybrid collector, as compared with the conventional air collector, is lower in thermal efficiency but the merit that it exhibits with respect to power generation is far greater than what is needed to counterbalance the demerit. When the hybrid system is in heating operation, there is an ideal heat cycle of collection, accumulation, and radiation when the load is light, but the balance between accumulation and radiation is disturbed when the load is heavy. 4 refs., 8 figs., 3 tabs.

  10. Study on an optimum ratio of PV output energy to WG output energy in PV/WG hybrid system; Taiyoko/furyoku hybrid hatsuden system no saiteki yoryohi ni kansuru kento

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, S. [Kandenko Co. Ltd., Tokyo (Japan)

    1996-10-27

    A photovoltaic power (PV) and wind generated power (WG) are an unlimited clean energy source, yet their output is unstable depending on the fluctuation of weather conditions such as solar radiation and wind velocity. Consequently, a large-scale power storage equipment is necessitated leading to a high cost especially in an independent system. As a solution, a method is available in which PV and WG are combined so that the effect may be utilized for stabilizing the output of a system as a whole, at a site where a fluctuation pattern is different between photovoltaic energy and wind energy. In building a hybrid system by PV and WG, sites with such supplementary effect existing were selected from the viewpoint of stabilizing the fluctuation of the power generation in the long run; and then, an examination was made on the optimum PV capacity ratio (%Ppo) in each site. As a result, it revealed that the %Ppo had great bearing on a ratio of PV energy fluctuation to WG, which was converted to a numerical formula. A comparatively simple examination by means of meteorological data also indicated that the share ratio was possibly optimized between the quantities of PV and WG energy. 4 refs., 2 figs., 2 tabs.

  11. Study on wave power generation of electricity using torsion arc blade type horizontal axis wind turbine; Nejire enko yokugata suihei jiku fusha wo mochiita haryoku hatsuden ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, N.; Kishimura, K. [Meiji University, Tokyo (Japan)

    1996-10-27

    Windmilling characteristics of a combination of a torsion arc blade type (TABT) horizontal axis wind turbine and a reverse torsion arc blade type (RTABT) horizontal axis wind turbine were evaluated in a wave activated power generation experiment. The TABT wind turbine had six blades, and the front and rear parts of the blade were twisted in the same direction, which caused the direction of rotor rotation to change as the direction of wind along the shaft changed. The RTABT wind turbine had twelve blades, and the front and rear parts of the blade were twisted reverse to each other, which allowed the direction of rotor rotation to stay constant even in the presence of wind direction reversal. To keep the direction of rotor rotation unchanged in the presence of flow direction reversal along the power generating turbine shaft, a single-stage type RTABT wind turbine and a double-stage type were used, the double-stage type being a series connection of a first-stage RTABT (for blowout and suction) and second-stage TABT (for blowout only). Both single-type and double-type rotated in the same direction irrespective of the direction of air flow. The output of the double type was obtained by adding up the values obtained from the individual turbines. The double type was two to three times higher in efficiency than the single type in turbine revolution and power output. 2 refs., 13 figs.

  12. Evaluation report on research and development of an ultra-advanced processing system. Sections 1 and 2; Chosentan kako system no kenkyu kaihatsu ni kansuru hyoka hokokusho. 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-08-01

    The ultra-advanced processing system is intended to develop an ultra-advanced processing device technology and an ultra-advanced processing technology. These technologies are indispensable to create such new processing technologies as ultra-precision and ultra-micro processing, and ultra high-grade surface modification processing, which have been impossible by the processing technologies having been available to date. It is also intended to develop a measuring and evaluating technology to support the above technologies. The intended system makes it possible to produce 21st century electronic components and ultra-high grade environment resistant materials. In order to achieve these goals, research and development has been performed on the excited beam technologies such as large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology to assure the reliability of these technologies as the fundamental technologies. This project has begun in fiscal 1986, where fiscal 1987 has achieved development of component technologies related to the large output excimer laser and high-density ion beams, the ultra-precision machining device technology, the ultra-advanced processing technology using the above technologies, and the measuring and evaluating technology, and completed the device technology, having achieved the final target. (NEDO)

  13. Report on the FY 1999 study of the decomposition/removal of environmental pollutants using laser induced chemical reaction; 1999 nendo laser yuki kagaku hanno wo mochiita kankyo osen busshitsu no bunkai jokyo ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the cleavage of carbon-chlorine connection and decomposition of benzene rings which are hazardous causes of the environmental pollutants represented by dioxins, the photolysis of gaseous phase chlorobenzene used as a model compound was made using KrF and ArF excimer laser. The decomposition is high efficiency, and ArF shorter in wavelength can be compounded twice-four times as fast as KrF. It was found out that in the system where oxygen exists, carbon monoxide, carbon dioxide, acetylene, hydrogen chloride, etc. are produced as decomposition products. From the results of the gaschromatographical analysis, chlorine compounds were detected as solid phase decomposition products. However, by the oxygen existence effect and laser shorter wavelength effect, the formation of polychlorinated aromatics was controlled, and chlorine compounds were made non-pollutant together with the composition. It was indicated that the environmental clean-up technology using laser is effective for making low-concentration environmental pollutants non-pollutant, and it is a method to clean up the environment which has a wide range of the application field. (NEDO)

  14. Fiscal 1995 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1995 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The research and development were conducted jointly with Europe of an environmental harmony type high efficient catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. In the research and development of NOx removal catalyst such as zeolite base, reformation of mostly mordenite was done by ion exchange, ion implantation, skeleton element substitution, etc. A possibility was found out of applying the membrane formation method except ion implantation as reforming means. In the R and D of the complex oxide base NOx removal catalyst, it was found that the catalyst carrying copper and silver on silica and layer clay compound under optimum conditions shows peculiarly high activity, and there is little decrease in the activity, but rather increase in it even under vapor existence. An evaluation was made of NO resolution of direct resolution element carrying noble metal electrolyte on solid electrolyte, finding out that the highest NO selectivity is shown with Pd as electrolyte and at a baking temperature of about 1300degC. Development of high- and low-temperature catalysts was also made. 417 refs., 286 figs., 63 tabs.

  15. Factor endowments and foreign trade. Empirical evidence of the Leontief paradox for G5 countries; Boeki pattern no henka to yoso chikuseki. G5 shokoku ni kansuru Leontief paradox no kensho

    Energy Technology Data Exchange (ETDEWEB)

    Sakurai, N. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-01

    The standard trade theory, the Hecksher-Ohlin-Vanek (HOV) model, was used to verify and analyze the relationship between comparative priority patterns in Japan and other industrialized nations and existence amount of each production factor (labor, material capitals, human capitals, and knowledge capitals) for the period between 1970 and the early 1990`s. Variation in the comparative priority in one country relates closely with the state of accumulation of each production factor. When the postwar economic growth in Japan is viewed, gradual level elevation has been realized from the developing country type economy mainly composed of simple labor to heavy chemical industrialization using material capitals as its axis, prosperity in machine industries based on skilled labor and human capitals (mainly in the 1970`s) and to the high-tech scene supported by active R&D investments (after the 1980`s). However, in order to maintain international competition edge into the future among the intensifying high-tech competitions between the nations of the world, improvement is indispensable in basics of knowledge capitals (scientific and fundamental researches and intelligent laborers), which is weaker than what it is in the United States. Japan is consistent with forecast of the HOV theorem in terms of a country blessed with skilled labor as of 1990, where the Leontief paradox may be dissolved, however partial it is. 50 refs., 1 fig., 10 tabs.

  16. FY1998 report on the survey on total energy and material control. Pt. 2. Survey on feasibility to structure a circulation type society; 1998 nendo total energy and material control ni kansuru chosa hokokusho. 2. Junkangata shakai kochiku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes a survey on feasibility to structure a circulation type society. The TEMCOS is a technology to contribute to structuring a circulation type society by controlling energy and materials totally. In order for the technology to develop into one that fuses with districts, survey and research were made on specific possibility of inter-process linking. Particularly discussions were given on zero emission of wastes (by-products) by means of inter-process linking of the metal industries with the chemical and petroleum industries. Therefore, the actual status of by-products was investigated and narrowed down, utilization possibilities were proposed, and the future possibilities and development themes were put into order. In order to structure a sustainable circulation type society, it is indispensable to perform step-wise cascade utilization considering quality of the energy, not only recycling energies and resources. Focusing on recovery of waste heat of low-middle temperatures which is difficult to recover latent heat, plans were established on research themes. The plans include chemical utilization of low-middle temperature heat utilizing ammonia gas, storage of heat in cryogenic temperature waste gas to iron particles, and transfer and utilization thereof. (NEDO)

  17. Evaluation report on research and development of 'seawater purification and byproduct utilization'; 'Kaisui Tansuika to fukusanbutsu riyo' no kenkyu kaihatsu ni kansuru hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    Research, development, and evaluation were made on seawater purification for the purpose of supplying inexpensive city water stably in the future. In the research of the high flow rate long-tube type multi-stage flash process, basic characteristics were identified by studying fluidity, heat transfer, deaeration, and decarburization by using a test plant with a capacity of 3,000 m{sup 3}/d. A number of findings were derived in carrying out demonstration studies by using a test module with a capacity of 100,000 m{sup 3}/d. Research on heat transfer pipe materials covered a wide area including copper alloys, titanium and aluminum alloys, and ferrous materials, where a prospect was obtained on materials which may be practically usable in the future as transfer pipes in large seawater purifying equipment. Research on a concrete evaporator body proved that it is more economical than steel evaporators, and has sufficient corrosion resistance even against high-temperature brine. Other activities included researches on effects of contaminated seawater, brine diffusion, byproduct utilization, and total systems. Social and economic evaluations were also performed. (NEDO)

  18. FY1995 study of thermodynamic properties of HFC refrigerant mixtures for Lorentz-cycled new generation air-conditioning equipments; 1995 nendo Lorentz cycle ka shinsedai kucho kikiyo HFC kei kongo reibai no netsurikigaku seishitsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A hydrochlorofluorocarbon (HCFC) refrigerant, R-22, is currently being used almost exclusively as a refrigerant for conventional air-conditioning equipments. Since HCFCs are expected to be banned shortly, it is considered a crucial issue to support R and D of the air-conditioning system Lorentz-cycled with hydrofluorocarbon (HFC) refrigerants mixtures. In the present research project, therefore, it is aimed to reveal some of the essential thermodynamic properties of HFC refrigerant mixtures systematically. On the basis of a series of achievements for the last several years by the present research coordinator and his group regarding thermodynamic properties of single-component and blended HFC refrigerants, we have conducted following three major research programs rather systematically on which no challenges have ever been reported worldwide. Throughout a series of experimental as well as analytical researches performed so as to meet the objectives mentioned above, some novel knowledge and valuable outcomes could be obtained in the present study. (1) Precise measurements of vapor-liquid equilibrium properties with simultaneous determination of densities, latent heats of vaporization, and isobaric specific heat capacities in liquid phase. (2) Analytical studies to establish thermodynamic property modeling. (3) Feasibility study of evaluating the Lorentz-cycled performance. (NEDO)

  19. Desing of multivariable controller for the cement grinding process. A study on the robust control in closed grinding circuit. 3rd report; Cement funsai heikairo no tahensu seigyo kei no sekkei. Funsai heikairo no robust seigyo ni kansuru kenkyu ( 3 )

    Energy Technology Data Exchange (ETDEWEB)

    Matsuo, S.; Okano, Y. [Tokyo Univ. (Japan). Faculty of Engineering

    1998-04-25

    Study regarding the establishment of transfer function model and control strategy for cement grinding process has been carried out so far. Particularly, as for control strategy, establishment of hierarchy control or necessity of adding cut size control also in assistant control were proposed. In this report, design of multivariable controller considering the dynamic characteristics of the systems proposed above was studied. In the design of this report, application of H{sub infinity} robust control considering the corresponding nonlinearity or variation was investigated. Further, design of two-degree of freedom for improving quick-responsibility, or corresponding non-coherence were studied side by side. As a result, it was understood that the establishment of multivariable control system is effective for improving quick-responsibility and to maintain set value for fine particles regarding the grindability of worsened raw material, and also, as for the design of the H{sub infinity} robust control, the corresponding variable was identified quantitatively using the established model. 11 refs., 10 figs., 1 tab.

  20. Study on direct measurement of diesel exhaust gas flow rate. Development of ultrasonic exhaust gas flowmeter; Diesel hai gas ryuryo no chokusetsu sokuteiho ni kansuru kenkyu. Choonpa hai gas ryuryokeino kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, A.; Takamoto, M.; Yamzaki, H. [National Research Laboratory of Meteology, Tsukuba (Japan); Hosoi, K. [Japan Automobile Research Institute Inc., Tsukuba (Japan); Arai, S.; Shimizu, K. [Kaijo Corp., Tokyo (Japan)

    2000-02-25

    The partial flow dilution method is one of the typical measurement methods for particulate matter emission from diesel engines. In this method, exhaust gas at a transient flow rate should be transferred to a dilution tunnel at a constant ratio of exhaust gas. The present partial flow dilution method is used under steady-state engine operating conditions in lieu of direct flow rate measurement of exhaust gas. A more practical control of exhaust emission is, however, required world widely; therefore development of an exhaust gas flowmeter is indispensable in the partial flow dilution method for transient engine operating conditions. An ultrasonic exhaust gas flowmeter has been developed and been demonstrated to be capable of measuring the exhaust gas flow rate with sufficient accuracy. (author)

  1. Achievement report for fiscal 2000 on the fundamental research on functional sectional imaging system using optical interference; 2000 nendo hikari kansho riyo kokino danso gazo sokutei sytsem ni kansuru kiban kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-16

    This project promotes the fundamental research on the conventional OCT technology to make it applicable to wider clinical applications of diagnoses and therapies by greatly improving the technology in view of higher spatial resolution, smaller size, and functional diversification. The research is supported by the medical and engineering cooperative research that utilizes the medical and engineering knowledge. Furthermore, as the fundamental technologies for the next generation, the sectional image measuring technology is established that makes possible to measure the three-dimensional flow and movement such as blood flow distribution in very small blood vessels, and performs the basic research on high-speed sectional image measurement to measure moving images of sectional images. The research contents for the current fiscal year may be summarized as follows: in the research on a small integrated optical element to make diagnostic application possible for skin cancers, retinal detachment, and cataract, research on trial production of a small OCT has been performed, and research on high spatial resolution has been implemented; furthermore, research was carried out on an endoscope integrated type OCT system intended of textural diagnoses of gastric cancer, hemorrhoidal cancer, and colic cancer, and on a sectional image measuring system intended of extracting biochemical information, and on a high-precision absorptive spectrum measuring technology for biogenic structures. (NEDO)

  2. FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

  3. Fiscal 1998 research cooperation project. Research cooperation on diversity preservation and sustainable use for living organisms; 1998 nendo seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report describes the titled research cooperation. Joint R and D with Thailand, Indonesia and Malaysia was made on collection and preservation of bio-resources such as tropical rain forest, and sustainable use of them by developing countries themselves. The project includes the simple identification and preservation technology of biospecies such as microorganism, assessment and monitoring technology of ecosystem, search of useful functions of biospecies, and construction of a bio-resource information network. This project promotes conversion of excessive hunting into resource conservation in agriculture, forestry and fisheries industries, and establishment of the basis of new product development in chemical and pharmaceutical industries. This project also contributes to preparation of the basic scheme of developed countries including Japan to countries holding bio-resources in addition to industrial basis preparation of every country. Until 1997, basis establishment has been made such as training of researchers, preparation of equipment and technical guidance, and in the final 1998, various results such as extraction of promising samples from microorganisms were obtained. (NEDO)

  4. FY 2000 study report on the study on technological development of the chemical processes of the next generation; 2000 nendo jisedai kagaku process gijutsu kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The technological development of the innovative chemical reaction processes is studied, in order to accomplish further energy saving, and reduction of resource consumption and environmental loads. Described herein are the FY 2000 study results. The program for systematization of the next-generation chemical processes systematically pigeonholes the undergoing projects and subjects to be studied, based on the principles of simplification, and sets the study fields of organic bulk chemicals, organic fine chemicals, highpolymer materials and inorganic materials. The program for investigation on next-generation chemical processes reviews creation and technological use of tailor-made biocatalysts, polymer materials which utilize wood resources, tailor-made reaction process engineering for handling fine particles in high-temperature reaction fields, production and processing of materials for high-performance polymer batteries, and extreme energy saving process for polyolefins, and proposes the revisions. The newly proposed study themes include novel C1 catalytic processes toward minimal wastes, and high utilization of biotechnology for novel processes to create materials. (NEDO)

  5. Fiscal 1998 research cooperation project on development of the easy-to-operate electronic design/production support system; 1998 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes 'Research cooperation on the easy-to- operate electronic design/production support system' which was promoted together with Asian countries as a part of the international research projects. This project is promoted by joint research with research organizations in China, Indonesia, Malaysia, Singapore and Thailand. The project promotes the interexchange and cooperation of researchers along the memoranda on MATIC (Manufacturing Technology International Cooperation) concluded between NEDO and research organizations every country. The project is implemented by CICC (Center of the International Cooperation for Computerization) through the contract with NEDO. CICC is promoting this project with the production system future integrated information system committee, MATIC committee, and automobile, home appliance, fiber and apparel working groups. The project has been promoted by the survey in fiscal 1994, the basic planning in fiscal 1995-1996, and development of the prototype information system in fiscal 1996-1998. The final demonstration test is scheduled in fiscal 1998. (NEDO)

  6. Leading research in FY 1995. Research of product evaluation and advanced measurements - Part 1 (product evaluation); 1995 nendo sendo kenkyu. Seihin hyoka kodo keisoku bunseki gijutsu ni kansuru chosa kenkyu - 1 (seihin hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Product evaluation has been investigated from a viewpoint of compatibility with human life by considering human being as the subject of life. This report describes the investigation results. Product evaluation is defined as evaluating products on a consumer-oriented viewpoint and informing consumers of the evaluation results. According to a questionnaire survey with regard to daily living products, products in the low degree of satisfaction in their usage were electric tooth brush, video camera, electric rice jar, vacuum cleaner, and electric iron. Contents of dissatisfaction with these products were classified by aspect, i.e., human aspect regarding human body/recognition, life aspect regarding functions of products and how to use them, and sensitivity aspect such as appearance of products. Thus, points at issue were clarified. As regards the human aspect, incompatibility between the size/form of products and human body/posture, and recognition psychological incompatibility such as difficulty in understanding function or operation of products were pointed out. Establishment of a method for measuring and evaluating the human`s body functions and the compatibility with products, and necessity of the acquisition of human`s body characteristic data and the consolidation positions are also described. 4 refs., 42 figs., 30 tabs.

  7. Report on follow-up for joint research of valuable resources recovery techniques from brackish water; Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku follow up hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes follow-up for research and development on the recovery of valuable resources, such as magnesium, bromine and boron, contained in the brackish water for manufacture of common salt in the coastal region of Mexico. For the field survey, salt garden, irrigation plant and manufacturing plant of dinning salt were inspected. The optimum site was examined by assuming desalination plant and solar pond. The groundwater in coastal regions is progressively salified. Since the coastal region is a tourist resort with an round-trip area of whales, environmental protection is indispensable. For the joint research with invited researchers, the solar pond system and fresh water generation were studied. As a result, it was found that the solar pond system is an excellent method for keeping thermal energy in a low cost at the salt garden with abundant solar energy, and that the desalination system combined with distilling is the most suitable method. 7 refs., 8 figs., 1 tab.

  8. Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

  9. Survey on the present state, policy and future view of power demand/supply in Sichuan province, China; Chugoku Shisensho no denryoku jukyu no jittai oyobi sono seisaku doko narabini kongo no tenbo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The Chinese government is carrying out various promotion measures of the interior region for the disparity correction between the interior and coastal regions, and development of China as a whole. Sichuan province is a major province for the promotion policy of the interior region which is located in the western part of China, and has an area of 570,000 square km, a population of 111.62 million, abundant natural resources, and the established industrial base. Based on the above situation, the present and future of energy situation and power demand/supply, and the policy trend and environmental measures of Sichuan province were analyzed to plan the cooperation policy on energy between Japan and China. The theoretical power generation capacity of water resources in Sichuan province is 150 million kW, and it is estimated that development of 1,062 power stations of 500kW class or more (91.67 million kW in total generator capacity and 515.3 billion kWh in annual generation output) is possible. Although Sichuan province has abundant hydraulic energy resources, it is largely dependent on coal-fired power generation. 4 figs., 34 tabs.

  10. Experimental study on the effect of fiber reinforced rubber-rolled pin of the bridge restrainer plate system; Gomu dansho pin wo mochiita rakkyo boshi renketsuban no seiteki oyobi doteki oto tokusei ni kansuru jikkenteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sonoda, Y.; Hikosaka, H. [Kyushu Univ., Fukuoka (Japan); Ishikawa, N. [Defence Academy, Yokosuka, Kanagawa (Japan)] Ikoma, N. [Shibata Industrial Co. Ltd., Osaka (Japan)

    1998-07-21

    As for the big earthquake like Hyogo Ken southern Earthquake, accident like collapsing of bridge girder is extremely difficult to prevent by only one bridge restrainer device. However, there exist considerable many spots not having enough space such as urban roads and so forth or the spots where the renewal of the existing restrainer device is difficult and as for these spots, it is thought that improvement of earthquake resistance performance is necessary by using the restrainer system based o the simple reformation of existing bridge restrainer plate system. In this report, under such condition, rolled pin winding the fiber reinforced rubber surrounding the connected pin was proposed as a technique for improving earthquake resistance by easy reformation of bridge restrainer of Spectacle type bridges which has many construction findings. In order to carry out characteristic and quantitative evaluation of the effect of rubber-rolled pin, two stages, o use level and ultimate level, were considered and static behavior and impact load characteristics for each level were studied experimentally, and comparison was made with the conventional steel pin. 13 refs., 19 figs., 6 tabs.

  11. Fiscal 2000 survey report. Research on bone-forming dental material capable of reducing plaque adhesion; 2000 nendo shiko fuchaku boshigata hone keisei shika zairyo ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development efforts are exerted to produce advanced dental materials equipped with such functions as plaque reduction, bactericidal effect, and early formation of hydroxyapatite (HAP). In the study of fluorine ion implantation for plaque reduction, it is found that in a specimen implanted with fluorine ions the adhesion of carius streptococci is reduced to 1/3-1/10 for the achievement of remarkable improvement. In particular, carious streptococcus multiplication is suppressed when the metal shield layer is replaced with a titanium mesh. For the realization of a thin film formation method for osteoblast multiplication through reforming the material surface in the study of bone-forming dental materials, film formation conditions under which a P/Ca rate which is quite near that of ameloblast are achieved by use of a high frequency magnetron sputtering device. A titanium plate coated with a thus-formed film is annealed for a great increase in its wet contact angle, and then adhesion of bacteria is reduced and an osteoblast multiplication rate is increased by 20% or more, as compared with the case of no treatment in a petri dish. (NEDO)

  12. Fiscal 1997 report on the survey of biological CO2 fixation using arid land and oligotrophic waters; 1997 nendo chosa hokokusho (kansochi, hin`eiyo kaiiki wo riyoshita seibutsuteki CO2 kotei ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This survey is aimed to investigate various measures to be taken for biological CO2 fixation, to synthetically study feasibilities of the measures from various aspects of CO2 fixation mechanism, scale, speed, and environmental effects and technical problems in case of introducing those, and to assess the measures quantitatively. In this fiscal year, a study was proceeded with of possibilities of carbon fixation by afforestation and that by fertilization into ocean. The paper defined significance of afforestation in arid land, and especially advantages in conducting researches in West Australia. Relationships were examined among afforestation, precipitation and topography. The result of the survey was described of water- and salt-transfer simulation methods. Studies of arid land were made in terms of photosynthetic speed, transpiration speed, soil characteristics, measuring methods for precipitation and vaporization amount, and the examples. Seven places of Leonora where water source and water quality were examined were selected, and the measuring results were described. The paper summed up the state of utilization of biomass energy obtained from forest and commented on a scenario on tree-planting. Finally, a possibility was stated of the carbon fixation by fermentation into ocean. 178 refs., 121 figs., 53 tabs.

  13. Consideration on buckling and plastic breakdown strength characteristics of a steel plate with surface layers of ultra fine grain microstructure (SUF); Hyoso chosairyu koban no zakutsu sosei hokai kyodo tokusei ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, M.; Yao, T.; Yajima, H.; Miyamoto, H.; Morita, S. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Ogihara, Y.; Ishikawa, T. [Nippon Steel Corp., Tokyo (Japan)

    1996-10-01

    Buckling and plastic breakdown strength characteristics of a structure fabricated by using new steel plates with surface layer made into ultra fine grain structure were analyzed and discussed by using a belt plate buckling and plasticity test and the finite element method. The tested steel plate has a thickness of 25 mm, and was fabricated for ocean vessel use, with surface layers on both sides of about 1/6 of the whole thickness having been made an ultra fine grain structure. As a result of a belt steel buckling and plasticity test on a steel plate with surface ratio of 29%, both of the initial yield stress and the buckling stress were found increased by about 4 to 10% as compared with a steel plate having surface ratio of 0%. An analysis by using the finite element method was made on square steel plates with a length of 80 cm, a width of 100 cm, and thicknesses of 12 mm and 24 mm. A result was obtained that, in the case of surface layer ratio of 33%, both of the initial yield stress and the maximum load withstanding force were higher by 5 to 16% than the case of surface ratio of 0%. Similar rise in strength was shown also in bend preventing plates which are basic constituting members of a vessel. 6 refs., 10 figs., 2 tabs.

  14. FY 1997 report on the study on the formation condition of hetero-structure of single-crystalline semiconductor thin films; 1997 nendo chosa hokokusho (tankessho no handotai usumaku hetero kozo no keisei joken ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Since ion implantation causes material degradation by formation of crystalline defects, and hydrogen embrittlement deteriorates material strength, reduction of such defects has been positively studied. Study was made on a new active application of hydrogen separation into ion implantation defects. After H ion implantation of a proper depth into single-crystalline Si and SiC and successive annealing, single-crystalline films of sub-micron to several micron thick were obtained by hydrogen-induced delamination at the implantation depth due to hydrogen embrittlement in crystalline defects. The implantation depth is dependent on implantation energy. H atom forms (111) face defect through connection with dangling bond of crystalline defects. This crystal face defect forms a delamination plane through (100) face cleavage. This hydrogen embrittlement delamination by ion implantation is applicable to production of light-weight high-efficiency single-crystalline Si solar cells, and large single-crystalline SiC wafers as new resource saving process. 33 refs., 19 figs., 2 tabs.

  15. Fiscal 1998 research report. Study on the feasibility of microorganism biotechnology for effective use of environmental pollutants. Pt. 2; 1998 nendochosa hokokusho. Kankyo osen busshitsu no shigenka no tame no biseibutsu bio technology riyo kanosei ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Study was made on the feasibility of microorganism biotechnology for effective use of environmental pollutants and unused resources. Microorganisms and microorganism enzymes for decomposing lignocellulose were viewed, and uses of hydrolysis products were summarized. Production of microorganisms applicable to fodder, composting, and production of energy sources (methane, hydrogen, ethanol) were studied. Use of vegetable fiber residues such as beer lees as fungus cultivation medium and conversion to valuable substances were also studied. Microorganisms treatment (MT) of wastes in fats and oils industry was summarized. Effective use of MT of protein waste from marine products was studied. MT of manures with the greatest impact on environment as livestock waste was summarized. The necessity of separate collection of domestic wastes, and composting and methane fermentation of kitchen garbage were reported. The feasibility of MT of plastic wastes, and decomposition of halogenated methane with high toxicity were also studied. (NEDO)

  16. Fiscal 1997 report on the cooperative research on the preservation and sustainable utilization of biological diversification; Seibutsu tayosei hozen to jizokuteki riyo nado ni kansuru kenkyu kyoryoku (1997 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Cooperative researches were conducted between Japan and Thailand, Indonesia and Malaysia for the purpose of the technology development to make developing countries themselves preserve bioresources existing in tropical forests and use those sustainably. The research subjects for Thailand are a strategical study on eating of the primates, improvement of a microorganism culture collection system, preservation of biological diversification using an artificial ecosystem, bioresource utilization, etc. The subjects for Indonesia are a study of a microorganism culture collection system, study of plant preservation technology, study of microorganism utilization technology, study of plant utilization technology, promotion of the founding of the Indonesia tropical bioresource information center, etc. The subjects for Malaysia are biological diversification database and gene bank, assessment/monitoring of the ocean ecosystem, assessment and inventory of the ecosystem using hi-tech technology, search/separation of bioactive substances originated from microorganism/plant, etc. 26 refs., 24 figs., 81 tabs.

  17. Research report of fiscal 1997. Study on total energy and material control (feasibility study on circulating society); 1997 nendo chosa hokokusho. Total energy and material control ni kansuru chosa (junkangata shakai kochiku kanosei chosa) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to construct real sustainable global environment and human society in the 21st century called the century of environment, not only the innovation of manufacturing processes technically supporting such the construction but also the conception including the innovation of the whole society from a wide viewpoint are essential. As a total energy and material control system (TEMCOS) concept, the view of an energy-saving circulating society is attempted which minimizes a total energy and material flow in Japan, and the role and issue of manufacturing industry, in particular, material industry are extracted. As one of the targets of such a concept, the conception of an eco-town is also described. Paying attention on some important material industries including a mass material flow and consuming a large amount of energy such as metal, plastics and automobile industries, the study result on a material flow for every industry is arranged, and some effective issues contributing to minimize a material flow and control energy consumption and CO2 emission are extracted. 80 refs., 67 figs., 30 tabs.

  18. Research of the elastic waves generated by a pulse laser. Excitation mechanism of elastic waves and application to nondestructive testing; Pulse laser de reikishita danseiha ni kansuru kenkyu. Danseiha reiki no mechanism to hihakai kensa eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Cho, H.; Takemoto, M. [Aoyama Gakuin University, Tokyo (Japan). College of Science and Engineering

    1994-07-20

    A bulk wave is generated when a pulse laser is irradiated to the material, and the characteristics of a Young`s modulus and Poisson`s ratio can be nondestructively estimated from the bulk wave. The generation mechanism of laser ultrasonic waves must be first clarified for such application. In this paper, fundamental research was conducted to study the generation mechanism of the elastic waves excited by a Q-switched Nd-YAG laser, and the generation method and characteristics of Rayleigh waves. The following result was obtained. A bulk wave is generated by the disk-like adiabatic expansion near the surface if the laser power is small when a spot-shape pulse laser was irradiated. A bulk wave is generated by the thin disk-like adiabatic expansion beneath the surface due to the thermal diffusion in the depth direction of a base material when the laser power becomes large. Moreover, a bulk wave is generated by the impact force due to abrasion and plasma when the power becomes still larger. The information on the bulk wave characteristics and Rayleigh wave was also obtained. 25 refs., 15 figs., 1 tab.

  19. Study on the annular leakage-flow-induced vibrations. 1st Report. Stability for translational and rotational single-degree-of-freedom systems; Kanjo sukimaryu reiki shindo ni kansuru kenkyu. 1. Heishin oyobi kaiten 1 jiyudokei no anteise

    Energy Technology Data Exchange (ETDEWEB)

    Li, D.W. [Hitachi, Ltd., Tokyo (Japan); Kaneko, S. [The University of Tokyo, Tokyo (Japan); Hayama, S. [Toyama Prefectural University, Toyama (Japan)

    1999-07-25

    This study reports the stability of annular leakage-flow-induced vibrations. The pressure distribution of fluid between a fixed outer cylinder and a vibrating inner cylinder was obtained in the case of a translationally and rotationally coupled motion of the inner cylinder. The unsteady fluid force acting on the inner cylinder in the case of translational and rotational single-degree-of-freedom vibrations was then expressed in terms proportional to the acceleration, velocity, and displacement. Then the critical flow rate (at which stability was lost) was determined for an annular leakage-flow-induced vibration. Finally, the stability was investigated theoretically. It is known that instability will occur in the case of a divergent passage, but the critical flow rate depends on the passage increment in a limited range: the eccentricity of the passage and the pressure loss factor at the inlet of the passage lower the stability. (author)

  20. Theoretical research relating to excitation spectrum of furan. Application of integral direct coupled cluster linear response (direct CCLR) method; Furan no reiki supekutoru ni kansuru ronriteki kenkyu. Integral-direct Coupled Cluster Linear Response (direct CCLR) ho no tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Shigemitsu, Yasuhiro. [Nagasaki Industrial Technology Center, Nagasaki (Japan)

    1999-07-01

    heoretical researches relating to excitation spectrum of furan have been carried out for many years, and they reveal the problems that should be solved in order to predict highly reliable excitation energy. In general, it is difficult to uniformly obtain highly reliable calculation results for all excitation states since different excitation states show different electronic correlative effects. Means for obtaining the electron states in ground state and excited state and calculating the energy difference thereof is the mainstream of the theoretical calculation of the excitation energy. CASSCF/CASPT 2 developed by Roos et al. is a typical method excellent in quantitative description. Recently, the comparison between direct CCLR and CASSCF/CASPT 2 as examples for calculating the excitation spectrum of furan was carried out by using the same ground function. For Rydberg excitation, CC3, CAS, CASPT 2 show good agreement with each other. (NEDO)

  1. Fiscal 1996 report on the survey of making models for introducing petroleum substituting energy systems. 3; 1996 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In the introduction of new energy and promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with courses for how to construct infrastructures of towns or cities and features of facilities in case of regional development, arrangement of facilities, etc. In fiscal 1996, each of the petroleum substituting energy systems which were invented in fiscal 1996 was arranged, and the main systems were shown in image in pamphlets. Namely, those are related to photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of unused energy, cogeneration, load levelling, wide-area energy supply, etc. Characteristics of each of the petroleum substituting energy systems were arranged from viewpoints of introducibility, scale, features of supply power/heat, economical efficiency and environmental characteristics, and subjects. Typical examples of the introduction in the country were outlined in terms of introduction sites, actual operational results, and effects. 7 figs., 4 tabs.

  2. Report for fiscal 1998. Joint research of environment-friendly system for effectively utilizing water resources; 1998 nendo hokokusho. Kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The research is conducted in cooperation with Industrial Technology Development Institute of the Philippines, and aims to solve water related problems such as unstable water supply and water quality pollution though developing a waste water treatment and recycling system which is easy to operate and maintain, low in cost, and usable in the Philippines. Fiscal 1998 is the second year of the project. Statistics are studied about the load that each industrial branch imposes on water for its pollution, and it is found that food manufacturers, paper pulp mills, and fiber dyeing plants are heavily responsible for water pollution. A method consisting of single-tower UASB anaerobic treatment and activated sludge treatment is applied as a water treatment process to Ram Food Products Corporation, and its optimization is studied. A removal rate 60% is achieved after a 12-hour treatment period at a COD (chemical oxygen demand) rate of 8g/liter/day. A method consisting of coagulating sedimentation and activated sludge treatment is applied to the waste water from a Solid Mill Corporation dyeing plant, when it is found that the water after ultimate treatment is almost colorless and that COD is 76mg/liter and BOD (biological oxygen demand) 13mg/liter, and these suggest that the waste water is recyclable. Since it is low in COD removing rate, the application of anaerobic treatment to high-concentration water after washing is not appropriate. (NEDO)

  3. Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

  4. 1998 research cooperation project. Research cooperation on environment-compatible type water resource effective-utilization system; 1998 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the purpose of securing water stably and preventing water pollution in the Philippines, R and D were carried out on a wastewater treatment and water reclamation and reuse system which is easy to operate and maintain and low in cost through the research cooperation between the Philippine Industrial Technology Development Institute and Japan. According to the survey result of statistical data concerning water pollution load structure by industrial wastewater classified by the industry in the Philippines, enumerated are the food manufacturing industry, paper pulp manufacturing industry, and the textile dyeing industry as those greatly affecting water pollution in BOD exhaust and wastewater, etc. Consequently, with Ram Food Product Co. of vegetable processing and Solid Mill Co., of textile dyeing as plants to be studied, a wastewater treatment test was performed in a laboratory scale. From the result of the test, the pilot plant was basically designed to have 'anaerobic + aerobic treatment + tertiary treatment' for the treatment process, with an one-tank type UASB method used as the anaerobic treatment, with a sand filtration + activated charcoal treatment as the tertiary treatment, and with the cost effectiveness for water reuse set to be examined. (NEDO)

  5. Reports on research achievements in developing high-performance industrial furnaces in fiscal 1998 (Research and development of high-performance industrial furnaces). Volume 1; 1998 nendo koseino kogyoro nado ni kansuru kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    From the reports on research achievements in developing high-performance industrial furnaces in fiscal 1998, the report volume 1 was prepared as a research achievement report of each working group, detailing fundamental researches, heating furnaces, and heat treatment furnaces. The fundamental researches have researched combustion evaluating technology, characteristics of the area in the vicinity of a combustor, characteristics of combustion of high-temperature air, heating characteristics of a furnace to investigate effect of local heat absorption, and combustion evaluation. For the heating furnaces, the following subjects were studied: development of an in-furnace combustion model, summary of an experiment for evaluating high-temperature air combustion, furnace height relative to combustion heat transfer characteristics, heat loss minimizing technology, combustion heat transfer characteristics of liquid fuels, optimal operation of the high-temperature air combustion, basic control in heating control, and steel piece heating control. Studies were performed for the heat treatment furnaces on the case of a direct firing furnace in evaluating the heat transfer characteristics, the case of a radiant tube furnace, application of thermal fluid simulation technology, furnace averaging technology, soot reducing technology, control technology, and trial design on a high-performance heat treatment furnace. (NEDO)

  6. Thermodynamics on the formation of non-metallic inclusion of spinel (MgO-Al2O3) in liquid steel; Yokochu deno spinel (MgO/Al2O3) hikinzoku kaizaibutsu seisei ni kansuru netsurikigaku

    Energy Technology Data Exchange (ETDEWEB)

    Ito, H.; Hino, M.; Banya, S. [Tohoku University, Sendai (Japan)

    1998-01-25

    Spinel in liquid steel is an issue as a non-metallic inclusion in steel, and its producing conditions were discussed thermodynamically. Consideration was given that Mg will elute due to MgO refractories and Al in liquid steel, whereas Mg reacts with dissolved oxygen and deoxidation product Al2O3 to produce spinel. The appearing oxidation product phases include MgO, MgO-Al2O3 and Al2O3. Spinel production was handled as composite deoxidizing reaction of an Al-Mg-O system or an Mg-Al-Ca-O system, and an experiment was performed. An experiment using a dolomite crucible derived at 1873 K the cross product terms related to Mg, Al, Ca and O. These values and previously reported values on Mg, Ca and Al deoxidation equilibrium were used to prepare a phase stability chart which specifies kinds of deoxidation products produced when Al is deoxidized in an MgO-based refractory container. The subject systems are Mg/ MgO-Al2O3/Al2O3 and MgO/ MgO-Al2O3/ CaO-2Al2O3. It was verified that the phase stability chart agrees with the experimental results. 17 refs., 8 figs.

  7. Fiscal 1997 report on the results of the international standardization R and D. International standards for computers/manikins; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Computer manikin ni kansuru kokusai hyojun kikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Through the development of computer manikins (CM) which assess human adaptability to products and environments, a draft for international standardization was worked out to propose to ISO. A draft for the international standardization was presented to ISO through a development of `a structure model` changing based on human attributes, a study of `a motion model` enabling changes in posture and movement, a study of `an evaluation model` evaluating attainment ranges and ecodynamic loads, and a development of `computer functions` realizing the above-mentioned functions. The development of CM having the following characteristics: a function to reproduce `the structure model` based on the ISO7250 human body dimensional measuring values which were regulated in items for the human body dimensional measuring, a function to change posture/movement based on the joint movable range data, a function to evaluate geometrical human adaptability such as attainment ranges. As a plug-in to Autodesk Mechanical Desktop 2.0, the above-mentioned functions were realized, and the modular structure platform was constructed which enables the wide-range cross-industry option and functional expansion by the advance of CM. 7 refs., 41 figs., 18 tabs.

  8. Fiscal 1997 survey report on the trend of global warming protection measures of substituting freons; 1997 nendo chosa hokokusho (daitai freon no chikyu ondanka taisaku doko ni kansuru chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The trend survey was conducted of global warming protection measures by participation in international conferences, scientific society meetings and lecture meetings, and by literature surveys. We participated in the international conference on ozonosphere protection measures. In the 9th meeting of the nations which concluded the Montreal Protocol, the strengthening of restrictions on methyl bromide was decided on. In the UNEP solvent technology selection conference and the OORG conference of the World Bank, reports were made on substituting solvents in Japan, activities supporting developing countries, and the developmental trend of urethane use foaming agent. In the international conference on ozonosphere protection measures, introduced were the present status of Japan`s ODA for developing countries and examples of success of the substitution in the solvent field. The paper included nine reports on CFC destruction technology related literature made public in the past one year. The paper also introduced a comparative study of de-HCFC substituting technology at U.S. Oak Ridge National Laboratory, U.S. EPA`s prediction of emission of fluorine 3 gas, the predicted value of HFC emission and trial calculation of contributing rate in all greenhouse gases by IIR, Green Peace and Elf Atochem, and NOAA`s measured data on SF6 in the atmosphere. 49 refs., 46 figs., 26 tabs.

  9. JUDGE project: a continental scientific drilling into plate subduction zone. 8. On archives of data and information of JUDGE; Shizumikomitai eno kussaku keikaku JUDGE. 8. Kussaku shishiryo archive ni kansuru kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miyazaki, T. [Geological Survey of Japan, Tsukuba (Japan); Tomizawa, N. [Schlumberger K.K., Tokyo (Japan)

    1997-04-28

    Systems for managing the data expected to be generated during the implementation of JUDGE (Japanese Ultra-deep Drilling and Geoscientific Experiments) Project are discussed from a viewpoint of archive construction. An archive system describes data in a computer system in compliance with grammar called a data model, and this enables efficient presentation and retrieval of information. Object data that is various in kind is classified by such categories as the class and the attribute. A data model means a format. The archive system conceptual design in this report consists of three layers for the user and four subspaces for data operation. This conceptual design is subjected to evaluation using actual data and existing systems, and it is found that the conceptual design is equipped with functions of storing and managing data and presenting information to the user. The AssetDB is an application that manages data of various types and functions (data relative to seismic exploration, logging, excavation, etc.). The function of the data processing, analytic subspaces is quite important in constructing archive systems. 7 refs., 3 figs., 3 tabs.

  10. Wind-resistant design for high-rise buildings. Pt. 1. Vertical distribution of strong wind in typhoons captured by Doppler sodar; Chokoso kenchikubutsu no taifu sekkei ni kansuru kenkyu. 1. Kyofuji no fusoku no enchoku bunpu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Goto, A.; Kawaguchi, A. [Obayashi Corp., Tokyo (Japan)

    1999-07-10

    Wind structure in the lower atmosphere is studied observationally by using Doppler sodar. Observations have been carried out in Okinawa since 1994, focusing on the vertical profiles of the mean wind speed under strong wind conditions and comparing the differences of characteristics of wind structures between typhoon and non-typhoon conditions. It is found that the lower atmosphere tends to have a two-layered structure on typhoon days, where the layer with nearly constant wind speed is embedded in the other layer and has a vertical distribution of wind speed that is represented well by power laws. In the layer of nearly constant wind speed, the mean wind speed observed by the Doppler sodar corresponds well with that observed by rawin sonde. At the same time, it shows a good correspondence with the gradient wind speed derived from a theoretical typhoon model. Vertical profiles of mean wind speed under strong, but non-typhoon conditions, have similar profiles to those of the AIJ recommendation, while the lower boundary of the constant velocity layer often has an altitude of less than one hundred meters under typhoon conditions, which is significantly lower than the empirically known gradient height. Application of the results of this study to wind-resistant design of high-rise buildings is also discussed. (author)

  11. FY 1998 Report on development of large-scale wind power generation systems. Research on the future prospects of wind power generation systems; 1998 nendo ogata furyoku hatsuden system kaihatsu. Furyoku hatsuden system no shorai tenbo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Current status of wind power generation in Japan and situations in foreign countries ahead of Japan are surveyed, in order to clarify the prospects for the future diffusion and expansion of wind power generation systems in Japan. The surveyed trends of wind power generation in Japan include those related to mandatory laws and regulations, e.g., the Electricity Enterprises Act, introductory and operation situations in local autonomies and electric power companies, and R and D efforts by academic and research organizations. The surveyed wind power generation situations in foreign countries include trends of international standardization for wind power generation, and global situations of introducing these systems. The on-the-spot oversea surveys include location/wind conditions in Greece's islands, cyclone-caused damages in India, World Renewable Energy Congress in Perth and advanced technologies in Europe for wind power generation systems, and the survey results are reported in detail. The surveyed R and D projects in Japan include the basic technological R and D plans (draft) for, e.g., wind power generation systems for isolated islands. (NEDO)

  12. Research cooperation project on manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC); Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To support the advancement of basic industries including machine industry in Asian countries, research cooperation has been conducted for developing the manufacturing technology supported by advanced and integrated information system suitable for actual circumstances of individual countries. For the automotive and the parts industries, it is significant for the preparation works of manufacturing in overseas factories to possess common information between Japan and overseas factories. In this project, a system is constructed, which can be used in industries surrounding automotive industry, such as parts and facility industries, as well as in the automotive industry. In FY 1996, a primary system has been developed, and the demonstration tests were carried out. For the home electric machine and the parts industries, the technology applicable to the design of printed board circuit was developed, and the catalog of electronic parts was constructed. In FY 1996, a preliminary prototype system of the electronic parts catalog system was designed and developed. For the textile and apparel industries, the EDI, exchange system of CAD/CAM data, and construction of data bank were investigated. 87 figs., 19 tabs.

  13. Report on evaluation on endocrine disturbing effect of chemicals and development of test methods; 1999 nendo kagaku busshitsu no naibunpi kakuran koka ni kansuru hyoka oyobi shikenho no kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With regard to endocrine disturbing effect being the new deleteriousness of chemicals, data were collected and evaluated by using the existing testing methods, data were collected by using the screening test, the testing methods were developed, and international investigation was carried out to establish the risk evaluation methods. In the evaluation by using the existing test methods, seven substance groups deficient in deleteriousness data qualitatively and quantitatively were given reproduction toxicity tests to evaluate availability of the endocrine activity. Development of the screening test method has been carried out by participating the validation test by OECD to make the uterotrophic assay method and the Hershberger assay method a test guideline having international matching property. International investigations to establish the risk evaluation were executed on the molecular mechanism of nuclear receptors, the chemical, metabolic and environmental behaviors of endocrine active substances, the effects of the endocrine active substances on experimental animals and human, the utilization thereof for risk assessment in human, and the effects of endocrine disturbance acting substances in wildlife species. (NEDO)

  14. FY 1998 annual report on the exploration and production of functional peptide from unutilized protein resources; 1998 nendo miriyo tanpakushitsugen kara no kinosei pepuchido no tansaku to seisan ni kansuru kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project is aimed at promotion of effective utilization of unutilized resources by transforming histidine-containing peptide (anserine), enzymatically hydrolyzed muscle protein present in lean salmon swimming off the Sanriku District in the spawning season, into functional peptide. A reactor system, comprising an enzyme-immobilized column and rotary bioreactor, is investigated to efficiently produce peptide by enzymatically hydrolyzing the water-insoluble muscle protein. Anserine is isolated by ethanol extraction, ion-exchanging and partition chromatography. The TPTZ and ABTS methods are developed for speeding up measurement of the antioxidant activity. The salmon muscle protein is hydrolyzed by 3 types of enzymes, to measure the free radical erasing activity by the ABTS method. The enzymatically hydrolyzed protein is fractionated by gel permeation chromatography. The fractions having a molecular weight of 10,000 or less show strong antioxidant activity. The hydrolyzed protein shows improved activity by the iron rhodanide method when it has histidine at the center of tripeptide, and strong radical erasing function when it has thyrosine or tryptophan at the carboxyl terminal. (NEDO)

  15. Study on electrical monitoring of fill-up improvement. Utilization of resistivity data for soil compaction management; Hiteiko mitsudo kanri ni kansuru kisoteki kenkyu. Moritsuchi seko kanri eno hiteiko yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, N.; Hiramatsu, W. [Dai Nippon Construction, Gifu (Japan); Sugano, T. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1996-10-01

    At present, measurement of wet density and water content by radio isotope (RI method) is used for filling management. It is supposed for filling in road construction that putting-out thickness of banking material reaches nearly 1m in the future rapid construction, however, use of RI method is difficult because of inserting and installing of a radiation source rod, large measuring apparatus, and the legal regulation on radioactivity intensity. Application of resistivity measurement was thus considered. Since resistivity has the same parameter as compaction curve, and monotonously decreases with an increase in water content by volume, it is applicable as construction management index. The management reference of resistivity (Rm) is set by plotting of a compaction curve and corresponding resistivity curve, determination of the reference resistivity (Ro) corresponding to a maximum dry density and optimum water content ratio, and setting of the allowance to Ro according to soil or application. It was clarified that Rm is applicable as set for every filling material. 1 ref., 10 figs., 2 tabs.

  16. Research cooperation report for fiscal 1997 on the environment-friendly system for effectively utilizing water resources; 1997 nendo kankyo taiogata mizushigen yuko riyo system ni kansuru kenkyu kyoryoku itaku gyomu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This effort exerted in cooperation with the Philippines aims to solve problems related to water resources such as stable supply and pollution of water through developing a waste water treatment/water reuse system which is easy to operate and maintain, and low in price. The ultimate goal includes (1) the construction of a waste water treatment/water reuse system comprising an anaerobic reaction tank and activated charcoal absorption tower, easy to operate and maintain, and low in price, (2) the employment of goods procurable in the Philippines, the goods including carriers for use in the anaerobic reaction tank, microbes for use in both aerobic and anaerobic reaction tanks, and activated charcoal for use in waste water reutilization, and (3) the establishment of optimum operating conditions for the waste water treatment/water reuse system by use of a pilot plant and the transfer of operating and managing techniques to the Filipino counterpart. In this fiscal year, investigations are conducted to disclose the actualities of waste water treatment and water consumption by primary industries in the vicinity of Laguna de Bay, and the waste water to be the object of study and the place of pilot plant installation have been selected. Also conducted are investigations into the carrier, microbe, activated charcoal, etc., for use in the anaerobic reaction tank. (NEDO)

  17. Study on heat transfer of an osmotic heat pipe with a two-phase solution loop. 1st Report. Fundamental study; Niso yoeki junkan shinto heat pipe no netsu yuso ni kansuru kenkyu. 1. Kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ipposhi, S.; Imura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Ogata, A. [Kumamoto University, Kumamoto (Japan)

    1999-12-25

    In the prior paper, a loop-type osmotic beat pipe was investigated on the heat transport rate from the upper position to the lower. The beat transport rate of this osmotic heat pipe, however, was very small because of small driving force for the solution circulation. Therefore, the osmotic heat pipe with the higher driving force is devised. The larger driving force is produced by a two-phase flow taking place in the solution riser. For the sake of that, a vopor-liquid separator is installed at the top of the apparatus and a heated section is attached as some distance below the separator, so that buoyant force caused by density difference between the fluids in the solution riser and downcomer increases. This osmotic heat pipe with the two-phase solution circulation loop indicates the higher heat transport rate than that of the osmotic heat pipe shown in the prior paper. (author)

  18. Study on heat transfer rate of an osmotic heat pipe. 3rd Report. Estimation of heat transport limits; Shinto heat pipe no netsuyuso ni kansuru kenkyu. 3. Netsuyuso genkai no yosoku

    Energy Technology Data Exchange (ETDEWEB)

    Ipposhi, S.; Imura, H. [Kumamoto University, Kumamoto (Japan). Faculty of Engineering; Konya, K. [Oji Paper Co. Ltd., Tokyo (Japan); Yamamura, H. [Kyushu University, Fukuoka (Japan)

    1998-07-25

    This paper describes an experimental and theoretical study on the heat transport limits of an osmotic heat pipe operated under the atmospheric pressure, using aqueous polyethylene glycol 600 solution (0.1 - 1.0 kmol/m{sup 3}) as the working fluid and 18 tubular-type acetyl cellulose osmotic membranes. As a result, the correlation between the heat transport rate and the osmotic area was revealed, and the effects of the physical properties of the solution and the geometry (i.e. inside diameters of the flow lines, etc.) of the osmotic heat pipe on the heat transport rate were theoretically investigated. Also, the heat transport rate of the present osmotic heat pipe is about 85% compared with that under such an ideal condition that the solution of the average concentration is assumed to be filled in the solution loop. 4 refs., 9 figs., 1 tab.

  19. Studies of initial stage in coal liquefaction. Effect of decomposition of oxygen-functional groups on coal liquefaction; Ekika hanno no shoki katei ni kansuru kenkyu. 3. Gansanso kannoki no bunkai kyodo to ekika hanno eno eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Komeiji, A.; Kaneko, T.; Shimazaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    Pretreatment of brown coal in oil was conducted using 1-methyl naphthalene or mixture of tetralin and 1-methyl naphthalene as solvent at temperatures ranging from 300 to 430{degree}C under nitrogen atmosphere. Effects of the solvent properties on the structural change of oxygen-functional groups (OFG) and coal liquefaction were investigated by means of quantitative analysis of OFG and solid state {sup 13}C-NMR measurement. When hydrogen transfer from solvent was insufficient, it was suggested that brown coal molecules loose their hydrogen to be aromatized. While, at lower temperatures ranging from 300 to 350{degree}C, hydrogen contained in brown coal molecules was consumed for the stabilization of pyrolytic radicals, and the deterioration of liquefaction was not observed. When hydrogen transfer from solvent was insufficient at higher temperatures above 400{degree}C in nitrogen atmosphere during pretreatment in oil, crosslinking like benzofuran type was formed by dehydration condensation of hydroxyl group in brown coal, to deteriorate the liquefaction, remarkably. The addition of donor solvent like tetralin decreased the formation of crosslinking like benzofuran type, which suppressed the deterioration of liquefaction. 8 refs., 5 figs.

  20. Fiscal 1997 report on the results of the research on the development of high-performance industrial furnaces. Volume 3; 1997 nendo seika hokokusho (koseino kogyoro no kaihatsu ni kansuru kenkyu seika hokokusto)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A R and D was conducted for the purpose of developing remarkable energy conservation/CO2 reduction technologies. In fiscal 1997, the five working groups about the following were formed to have animated discussions: the basic research, heating furnace, heat treatment furnace, melting furnace, and tubular heating furnace. The research subjects are the pursuit/deepening of the base study on flame structures in high temperature air combustion, critical heat recovery of the system in high temperature air combustion, examination of the basic common technology on the ultimate optimization of the material heat transfer, construction of general-purpose experimental database, setting-up of design standards for general-purpose high-performance industrial furnaces, presentation of examples of the actual trial design based on the design standards and feasibility study of the practical application, preparatory support of the field test project on high-performance industrial furnaces for commercialization/diffusion/spread, etc. Further, how to arrange the developmental results was studied to make the results of the project useful for study of the prompt commercialization. 442 refs., 1444 figs., 311 tabs.

  1. Studies of initial stage in coal liquefaction. Effect of prethermal treatment condition with process solvent to increase oil yields; Ekika hanno no shoki katei ni kansuru kenkyu. Sekitan no maeshori joken to yozai koka

    Energy Technology Data Exchange (ETDEWEB)

    Shindo, T.; Komatsu, N.; Kishimoto, M.; Okui, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. ltd., Tokyo (Japan)

    1996-10-28

    Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogen transfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of THF-insoluble using high hydrogen-donor solvent and/or by adding catalyst. It was also found that the use of high hydrogen-donor solvent and highly active catalyst at the stage of prethermal treatment before the successive liquefaction was effective for improving the HS yield, i.e., liquefied oil yield. 2 refs., 5 figs., 1 tab.

  2. Studies on fluid drag measurement and fluid drag reduction of woman athlete swimming suit; Kyoeiyo mizugi no teiko sokutei ni kansuru kenkyu. Jintai mokei oyobi mizugi no ryutai teiko

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Y. [Mie University, Mie (Japan). Faculty of Engineering; Suzuki, T.; Suzuki, K. [Mie University, Mie (Japan); Kiyokawa, H. [Mizuno Corp., Osaka (Japan)

    1997-12-25

    Sport science progresses step by step in the world. This work is a challenge to develop the athlete woman swimming suit with low fluid drag. To begin with, the fluid drag of the woman swimming suit is very small. It is very difficult to measure the several percent difference in the fluid drag of the swimming suit. Special experimental apparatus is developed to measure the fluid drag, precisely. It can successfully measure the fluid drag of athlete woman swimming suits at the precision 1-2%. As a result, the cloth with low fluid drag is found. It is worked water repellent into every other stripe on the cloth. The cloth is woven of thin threads (polyester 80% and polyurethane 20%). Also, the relationship between fluid drag for the model body and the water depth from the water surface to the model body is investigated in details. 2 refs., 16 figs.

  3. ni potni list

    Directory of Open Access Journals (Sweden)

    Ana Krajnc

    1996-12-01

    Full Text Available Decembra 1994 je bila v Rimu velika mednarodna konferenca o permanentnem ali vse življenje trajajočem izobraževanju. Široki strokovni javnosti sta bila takrat prvič predstavljena tudi dva nova pojma: osebni učni načrt in učni potni list. Pri priči sta se prijela v teoriji in praksi - očitno sta bila oba predloga odsev potreb.

  4. Relation between shape of Ni-particles and Ni migration in Ni-YSZ electrodes – a hypothesis

    DEFF Research Database (Denmark)

    Mogensen, Mogens Bjerg; Hauch, Anne; Sun, Xiufu

    2016-01-01

    pressure (pH2O) gradient as previously observed [1], but in the present cases Ni seems to migrate up the pH2O gradient. However, it is also observed that there is a preceding phase in this Ni-YSZ electrode degradation, namely that the Ni-particles closest to the YSZ electrolyte loose contact to each other...

  5. Comprehensive theoretical studies on the low-lying electronic states of NiF, NiCl, NiBr, and NiI.

    Science.gov (United States)

    Zou, Wenli; Liu, Wenjian

    2006-04-21

    The low-lying electronic states of the nickel monohalides, i.e., NiF, NiCl, NiBr, and NiI, are investigated by using multireference second-order perturbation theory with relativistic effects taken into account. For the energetically lowest 11 lambda-S states and 26 omega states there into, the potential energy curves and corresponding spectroscopic constants (vertical and adiabatic excitation energies, equilibrium bond lengths, vibrational frequencies, and rotational constants) are reported. The calculated results are grossly in very good agreement with those solid experimental data. In particular, the ground state of NiI is shown to be different from those of NiF, NiCl, and NiBr, being in line with the recent experimental observation. Detailed analyses are provided on those states that either have not been assigned or have been incorrectly assigned by previous experiments.

  6. CONFIGURATION-INTERACTION IN NI METAL AND NI-ALLOYS AND HIGH-ENERGY SPECTROSCOPY

    NARCIS (Netherlands)

    TANAKA, A; JO, T; SAWATZKY, GA

    We discuss the electronic state of Ni atoms in Ni metal and of Ni impurity in Cu and Au metals from the viewpoint of 3d configuration interaction (CI) using the Anderson impurity model including atomic multiplets. On the basis of the discussion, we give an interpretation for the Ni 2p-core X-ray

  7. Laser alloyed Al-Ni-Fe coatings

    CSIR Research Space (South Africa)

    Pityana, SL

    2008-10-01

    Full Text Available The aim of this work was to produce crack-free thin surface layers consisting of binary (Al-Ni, Al-Fe) and ternary (Al-Ni-Fe) intermetallic phases by means of a high power laser beam. The laser surface alloying was carried out by melting Fe and Ni...

  8. Kinetics of Ni2Si growth from pure Ni and Ni(V) films on (111) and (100) Si

    Science.gov (United States)

    Harith, M. A.; Zhang, J. P.; Campisano, S. U.; Klaar, H.-J.

    1987-01-01

    The kinetics of Ni2Si growth from pure Ni and from Ni0.93V0.07 films on (111) and (100) silicon has been studied by the combination of He+ backscattering, x-ray diffraction, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM) techniques. The activation energies are 1.5 and 1.0 eV for pure Ni and Ni(V) films, respectively while the pre-exponential factors in Ni(V) are 4 5 orders of magnitude smaller than in the pure Ni case. The variations in the measured rates are related to the different grain size of the growing suicide layers. The vanadium is rejected from the silicide layer and piles up at the metalsilicide interface.

  9. Synthesis and catalytic performance of SiO2@Ni and hollow Ni microspheres

    Science.gov (United States)

    Liu, Xin; Liu, Yanhua; Shi, Xueting; Yu, Zhengyang; Feng, Libang

    2016-11-01

    Nickel (Ni) catalyst has been widely used in catalytic reducing reactions such as catalytic hydrogenation of organic compounds and catalytic reduction of organic dyes. However, the catalytic efficiency of pure Ni is low. In order to improve the catalytic performance, Ni nanoparticle-loaded microspheres can be developed. In this study, we have prepared Ni nanoparticle-loaded microspheres (SiO2@Ni) and hollow Ni microspheres using two-step method. SiO2@Ni microspheres with raspberry-like morphology and core-shell structure are synthesized successfully using SiO2 microsphere as a template and Ni2+ ions are adsorbed onto SiO2 surfaces via electrostatic interaction and then reduced and deposited on surfaces of SiO2 microspheres. Next, the SiO2 cores are removed by NaOH etching and the hollow Ni microspheres are prepared. The NaOH etching time does no have much influence on the crystal structure, shape, and surface morphology of SiO2@Ni; however, it can change the phase composition evidently. The hollow Ni microspheres are obtained when the NaOH etching time reaches 10 h and above. The as-synthesized SiO2@Ni microspheres exhibit much higher catalytic performance than the hollow Ni microspheres and pure Ni nanoparticles in the catalytic reduction of methylene blue. Meanwhile, the SiO2@Ni catalyst has high stability and hence it can be recycled for reuse.

  10. Study on unified fatigue strength assessment method for welded structure. Hot spot stress evaluating method for various combinations of plate thickness and weld leg length; Yosetsu kozo no toitsutekina hiro kyodo hyokaho ni kansuru kenkyu. Itaatsu to yosetsu ashinaga no kumiawase ni taisuru hot spot oryoku sanshutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Nihei, K.; Inamura, F.; Koe, S. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-12-31

    There has been tried to apply unified assessment method using hot spot stress, which is effective to evaluate fatigue strength of fillet welded structures for ships and marine structures. This method can be applied to complicated structures and is independent of welding processes. In this study, first, stress analysis has been conducted for two-dimensional fillet welded joint models with various combinations of plate thickness and weld leg length of general fillet structures by means of boundary element method. Then, critical position, which is not affected by local stress concentration due to bead, was determined from the detailed stress distribution in the vicinity of weld toe. As a result, a general equation has been proposed to estimate the hot spot stress by one-point representative method. Second, the fatigue tests of typical fillet welded joints have been conducted by applying this method. Consequently, it was demonstrated that the unified fatigue strength can be evaluated by the S-N data based on hot spot stress range determined from the proposed equation, independent of structural stress concentration. 22 refs., 14 figs.

  11. Fundamental study on the new method to estimate vibration level on a ship. Formulation of the damping matrix based on dissipation energy caused by fluid viscosity; Senpaku no shindo level suitei ni kansuru kisoteki kenkyu. Ryutai no nensei ni yoru san`itsu energy ni motozuku gensui matrix no teishikika

    Energy Technology Data Exchange (ETDEWEB)

    Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering

    1996-12-31

    It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. In order to analyze the compound vibration therein, a method was proposed, which estimates vibration levels without using the finite element method. However, the problem of mode decay ratio has not been solved. Therefore, this paper first describes a method to introduce an equivalent linear decay matrix. The paper then mentions difference in the decay effects due to fluid viscosity in a shallow and deep water regions. Furthermore, vibration levels in the deep water region were estimated in a model experiment to verify the estimation result. Under a hypothesis that two-node vibration in a rotating ellipse has displacement distributions in the deep and shallow water regions equivalent, and when a case of vibration in a layer flow condition is calculated, dissipation energy in the shallow region is larger than that in the deep region by about 26%. About 5% of the total dissipation energy is consumed at bottom of the sea. According to a frequency response calculation, estimated values for the response levels still differ from experimental values, although the trend that the vibration levels change can be reproduced. 6 refs., 15 figs., 2 tabs.

  12. Study on premixed combustion of diesel spray with high pressure fuel injection and a micro-hole nozzle using a rapid compression machine. 2nd Report. Improvement of combustion using low cetane number fuel; Kyusoku asshuku sochi wo mochiita bisaiko koatsu diesel funmu no yokongoteki nensho ni kansuru kenkyu. 2. Tei setan nenryo ni yori chakka okure wo jubun ni kakuhoshita baai

    Energy Technology Data Exchange (ETDEWEB)

    Lee, J.; Akiyama, H.; Iida, N. [Keio University, Tokyo (Japan). Faculty of Science and Technology

    1999-10-25

    This study was aimed at reducing Soot and NO{sub X} by uniform and lean distribution of fuel in diesel spray using high-pressure fuel injection and a micro-hole nozzle. But this injection system made ignition delay shorter. So that, it couldn't completely make uniform and lean distribution of fuel in diesel spray. Then, in addition to this injection system, using low cetane number of fuel, which can not easily ignited, we made ignition delay longer, and attempted to make complete uniform and lean distribution of fuel in diesel spray. The combustion event was observed by high-speed direct photography, ignition and combustion was analyzed by the combustion chamber pressure history, and KL values and flame temperatures was analyzed by the two-color method from the two dimensional flame image. (author)

  13. Study to take environmental symbiosis into consideration on housing construction. No.2. Experimental study on the thermal performance of K house in winter season; Kankyo kyosei ni hairyoshita sumai zukuri ni kansuru kenkyu. 2. Amagishi ni tatsu K tei no toki no onnetsu kankyo keisoku kekka

    Energy Technology Data Exchange (ETDEWEB)

    Nishikawa, K.; Ishihara, O. [Kumamoto University, Kumamoto (Japan)

    1996-10-27

    For the construction of houses that effectively utilize natural energy and impose less load on environments, an example of house building respecting environmental symbiosis is described. Reported herein are a heating system and the measurements of thermal environment in winter. In winter, the floor is heated by warm water from solar heat collectors circulating in pipes buried in downstair underfloor RC foundation. For the verification of the heating effect, comparison was made between the heater-provided southeast (SE) room and heater-unprovided northeast (NE) room, both downstairs. Warm water circulated in the underfloor pipes only in the daytime, the pipe surface recording the maximum of 32{degree}C in the daytime and the minimum of 17{degree}C early in the morning. At midnight, the SE room was warmer than the NE room by 2{degree}C. The slab surface in the SE room recorded 28{degree}C at the maximum and 17{degree}C at the minimum, but the temperature remained constant at 10{degree}C in the NE room. The rubble temperature was 17.5-20{degree}C in the SE room and approximately 11{degree}C in the NE room. It was noted that the SE room floor slab was capable of heat accumulation. The resident is a devotee of environmental symbiosis with mindset for enhancing natural energy utilization, burning an oil heater and a fireplace but intermittently. 1 ref., 12 figs., 1 tab.

  14. Comparative analysis of thermal storage cooling and storage battery cooling using photovoltaic generation. Part 2. Research on architectural systematization of energy conversion devices; Taiyoko hatsuden ni yoru chikunetsu reibo to chikuden reibo ni tsuite. 2. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, N.; Kimura, G.; Fukao, S.; Shimizu, T.; Sunaga, N.; Tsunoda, M.; Muro, K.; Yamanaka, S. [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    For use in energy self-sufficient buildings, a system was studied capable of retaining for its own use the excess of power produced by a photovoltaic power generation system without releasing it to the commercial system. Summertime cooling was considered. The storage battery cooling system was provided with two solar cell systems and, in the daytime, one was used for cooling and the other for charging batteries for nighttime cooling. In the cold heat storage cooling system, cold heat accumulators (red bricks) were provided in the wall and floor, and under the floor, and the floor was a grating for proper ventilation between the room and underfloor space. With the solar cell-driven air conditioner out of operation, cold heat was fed to the room from the underfloor cold heat accumulators by a fan. In storage battery cooling, solar power covered 60% of what the air conditioner used. In the presence of sufficient power in storage, the air conditioner stayed on at night without buying commercial power, when the room temperature was 25{degree}C. In the cold heat accumulation cooling, 50% of the air conditioner power consumption was covered by solar power. It is recommended to install cold heat accumulators not in the room but in a separate space, such as the underfloor space, where they are exposed to the cooling cold air direct from an air conditioner for future retrieval of cold heat. 2 refs., 9 figs., 3 tabs.

  15. FY 1999 report on the results of the introductory study on the global environmental industry technology. Investigational study on the environmental creation technology by the application of ecosystem information functions; 1999 nendo chikyu kankyo sangyo gijutsu ni kakawaru sendo kenkyu seika hokokusho. Seitaikei joho kino oyo ni yoru kankyo sozo gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To know the state of environmental pollution before it clearly exists, an investigational study was made on the technology to measure environmental stress at high sensitivity, in wide range and at high speed using functions to respond chemical substances, etc. which living organisms have. The FY 1999 results were outlined. As to the application of ecosystem information functions, survey was conduced paying attention to the environmental stress response of each of the bacteria, algae, plants and animals, responses viewed from the manifestation of immunity antibodies which occurs inside living organisms and changes at genetic level, and responses of algae and plants in case of specifying environmental pollutants. In relation to the application of the biological amplification mechanism, survey was carried out on environmental stress signals sent from plants, selection of environmental stress index plants, detection of environmental pollutants using bacteria, high sensitivity detection using animal (nematode), etc. Concerning the standardization of the environmental measuring technology by the application of ecosystem information functions, survey was conducted on artificial molecular recognition sensor, antibody device sensor, biochips, system construction, etc. (NEDO)

  16. Formation of NiCrAlY/NiAl multi-layered coating by low pressure plasma spraying; Genatsu plasma yosha ni yoru NiCrAlY/NiAl tasomaku no seisei

    Energy Technology Data Exchange (ETDEWEB)

    Takizawa, H. [Industrial Res. Inst. of Nagano Pref., Nagano (Japan).; Yonehama, K.; Sugimoto, K.; Kobayashi, M. [Shinshu Univ., Nagano (Japan). Faculty of Education

    1997-12-15

    NiCrAlY/NiAl multi-layered coating was produced on SUS310S steel by means of mutual low pressure plasma spraying of NiCrAlY and Al powders which was accompanied with self-propagating high-temperature synthesis (SHS) reaction of metal deposits. The NiAl layer contained Ni3Al particles and Cr2Al phase along the fine grain boundary. Also, Ni3Al was detected in the NiCrAlY layer with a small amount of NiAl particles. As the result, high hardness was obtained in both the layers, i.e., 650HV in NiAl layer and 450HV in NiCrAlY one at 673K. The structure of the multilayered coating changed hardly during annealing lower than 973K because enriched Cr at NiCrAlY/NiAl interface suppressed NiAl + Ni3Al{yields}Ni5Al3 peritectoid reaction. The SHS reaction time of an compressed Al droplet in diameter of 50{mu}m was calculated as 4.17times10{sup -3} second. 20 refs., 9 figs., 3 tabs.

  17. niños preescolares

    Directory of Open Access Journals (Sweden)

    Claudia Rosario Portilla Ramírez

    2007-01-01

    Full Text Available Este estudio explora la relación entre la escritura y la comprensión de la referencia a través de una tarea de sinonimia en niños entre 5 y 6 años de edad, de origen latinoamericano, escolarizados en Barcelona (España. Las variables relacionadas con la tarea de sinonimia fueron (a la comprensión de la entidad lingüística nombre y (b el nivel de conceptualización de la escritura de los niños y la presencia de etiquetas escritas durante la tarea. Para la tarea de sinonimia se utilizaron pares de sinónimos dialectales del español (de Latinoamérica y de la Península Ibérica. Los resultados mostraron una diferenciación en el razonamiento de los niños, la cual dependía de la comparación entre lenguaje oral y lenguaje escrito en el desarrollo de la tarea, evidenciando una mayor aceptación de la sinonimia en la modalidad de lenguaje oral que en la modalidad de lenguaje escrito.

  18. Exclusive study of Ni+Ni and Ni+Au central collisions: phase coexistence and spinodal decomposition; Etude exclusive des collisions centrales Ni+Ni et Ni+Au: coexistence de phase et decomposition spinodale

    Energy Technology Data Exchange (ETDEWEB)

    Guiot, B

    2002-12-01

    The INDRA multidetector allowed us to study the Ni+Ni collisions at 32A MeV and the Ni+Au collisions at 52,4 MeV. Central collisions leading to 'quasi-fused' systems were isolated using multidimensional analysis techniques: the Discriminant Analysis and the Principal Component Analysis. Comparison with a statistical model shows that the selected events are compatible with thermodynamical equilibrium. The average thermal excitation energy is 5A MeV for both systems. Calculations of heat capacities show that the deexcitation of the hot sources are akin to a liquid-gas phase transition of nuclear matter. Indeed heat capacities exhibit a negative branch as expected for a phase transition of a finite system. The dynamics of this phase transition has been investigated by applying the charge correlation method. An enhanced production of events with equal-sized fragments has been evidenced for Ni+Au at 52A MeV. No signal was found for Ni+Ni at 32A MeV. Finally this method was improved by taking into account the total charge conservation. The signal is seen more clearly for Ni+Au at 52A MeV, but is ambiguous for Ni+Ni at 32A MeV. The path followed in the state diagram, or the involved time scales, seem to be different for these systems. (authors)

  19. Effect of air annealing on structural and magnetic properties of Ni/NiO nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Nadeem, K., E-mail: kashif.nadeem@iiu.edu.pk [Nanomagnetism and Nanotechnology Laboratory, International Islamic University, Islamabad (Pakistan); Ullah, Asmat; Mushtaq, M.; Kamran, M.; Hussain, S.S. [Nanomagnetism and Nanotechnology Laboratory, International Islamic University, Islamabad (Pakistan); Mumtaz, M. [Materials Research Laboratory, Department of Physics, International Islamic University, Islamabad (Pakistan)

    2016-11-01

    We reported systematic study on structural and magnetic properties of nickel/nickel oxide (Ni/NiO) nanoparticles annealed under air atmosphere at different temperatures in the range 400–800 °C. The XRD spectra revealed two phases such as Ni and NiO. The average crystallite size increases with increasing annealing temperature. A phase diagram was developed between two phases versus annealing temperature using XRD analysis. At lower annealing temperatures, Ni phase is dominant which does not easily undergo oxidation to form NiO. The NiO phase increases with increasing annealing temperature. FTIR spectroscopy revealed an increase in the NiO phase content at higher annealing temperature, which is in agreement with the XRD analysis. SEM images showed that nanoparticles are well separated at lower annealing temperatures but get agglomerated at higher annealing temperatures. The ferromagnetic (FM) Ni phase content and saturation magnetization (M{sub s}) showed nearly the same trend with increasing annealing temperature. The nanoparticles annealed at 500 °C and 800 °C revealed highest and lowest M{sub s} values, respectively, which is in accordance with the XRD phase diagram. Coercivity showed an overall decreasing trend with increasing annealing temperature due to decreased concentration of FM Ni phase and increasing average crystallite size. All these measurements indicate that the structural and magnetic properties of Ni/NiO nanoparticles are strongly influenced by the annealing temperature. - Highlights: • Air annealing effects on structural and magnetic properties of Ni/NiO nanoparticles have been studied. • The XRD spectra revealed two phases such as Ni and NiO. • A phase diagram was developed between two phases versus annealing temperature using XRD analysis. • The magnetic properties are well governed by ferromagnetic Ni phase.

  20. A threonine stabilizes the NiC and NiR catalytic intermediates of [NiFe]-hydrogenase.

    Science.gov (United States)

    Abou-Hamdan, Abbas; Ceccaldi, Pierre; Lebrette, Hugo; Gutiérrez-Sanz, Oscar; Richaud, Pierre; Cournac, Laurent; Guigliarelli, Bruno; De Lacey, Antonio L; Léger, Christophe; Volbeda, Anne; Burlat, Bénédicte; Dementin, Sébastien

    2015-03-27

    The heterodimeric [NiFe] hydrogenase from Desulfovibrio fructosovorans catalyzes the reversible oxidation of H2 into protons and electrons. The catalytic intermediates have been attributed to forms of the active site (NiSI, NiR, and NiC) detected using spectroscopic methods under potentiometric but non-catalytic conditions. Here, we produced variants by replacing the conserved Thr-18 residue in the small subunit with Ser, Val, Gln, Gly, or Asp, and we analyzed the effects of these mutations on the kinetic (H2 oxidation, H2 production, and H/D exchange), spectroscopic (IR, EPR), and structural properties of the enzyme. The mutations disrupt the H-bond network in the crystals and have a strong effect on H2 oxidation and H2 production turnover rates. However, the absence of correlation between activity and rate of H/D exchange in the series of variants suggests that the alcoholic group of Thr-18 is not necessarily a proton relay. Instead, the correlation between H2 oxidation and production activity and the detection of the NiC species in reduced samples confirms that NiC is a catalytic intermediate and suggests that Thr-18 is important to stabilize the local protein structure of the active site ensuring fast NiSI-NiC-NiR interconversions during H2 oxidation/production. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

  1. Microstructural investigations of Ni and Ni2Al3 coatings exposed in biomass power plants

    DEFF Research Database (Denmark)

    Wu, D. L.; Dahl, K. V.; Christiansen, T. L.

    2017-01-01

    temperature pack cementation. After exposure, microstructural investigations were performed by light optical and electron microscopy (SEM-EDS). Electroplated Ni coatings were not protective in straw firing power plants and exhibited similar corrosion morphology as uncoated tubes. For Ni2Al3 coatings......The present work investigates the corrosion resistance of Ni and Ni2Al3 coated austenitic stainless steel (TP347H) tubes, which were exposed in a biomass-fired boiler with an outlet steam temperature of 540 °C for 6757 h. The Ni2Al3 coating was produced by electroplating Ni followed by low......, the nickel aluminide layer was no longer adherent to the tube and was only found within the deposit. However, Ni2Al3 coatings had provided some protection compared to uncoated and Ni coated tubes. The formation of nickel chloride binds aggressive chlorine and slows down the active oxidation mechanism...

  2. Adherencia al tratamiento en niñas y niños con VIH

    OpenAIRE

    Ana María Ruiz Navia; Sandra Liliana Enríquez Lara; Paula Andrea Hoyos Hernández

    2009-01-01

    Este artículo describe y determina el grado de adherencia al tratamiento en niños y niñas con VIH/ SIDA teniendo en cuenta los comportamientos y las variables asociadas a ésta. La muestra estuvo conformada por 1 niño y 5 niñas, diagnosticados con VIH, y su respectivo cuidador primario, quienes respondieron a la entrevista semiestructurada de evaluación de adherencia para niños y niñas con VIH/ SIDA ad hoc y a la entrevista semiestructurada de evaluación de adherencia para niños y niñas con VI...

  3. The Ni-Al-Hf Multiphase Diffusion

    Directory of Open Access Journals (Sweden)

    Romanowska J.

    2016-06-01

    Full Text Available The generalized Darken method was applied to simulate the diffusion between γ-Ni| γ’-Ni3Al and γ’-Ni3Al|β-NiAl interfaces. The results of calculations were compared with the experimental concentration’s profiles of nickel, aluminum and hafnium in aluminide and hafnium doped aluminide coatings deposited by the CVD and PVD methods on pure nickel. The method deals with the Wagner’s integral diffusion coefficients and thermodynamic data - activities of components. The experimental results agree with the simulated ones.

  4. Laser welding of NiTi wires

    Energy Technology Data Exchange (ETDEWEB)

    Gugel, H. [Institute for Materials, Materials Technology, Ruhr-University Bochum, Bochum (Germany)], E-mail: hajo.gugel@rub.de; Schuermann, A.; Theisen, W. [Institute for Materials, Materials Technology, Ruhr-University Bochum, Bochum (Germany)

    2008-05-25

    The special properties of nickel-titanium shape memory alloys are currently used in micro-engineering and medical technology. In order to integrate NiTi components into existing parts and modules, they often need to be joined to other materials. For this reason, the present contribution deals with the laser welding of thin pseudoelastic NiTi wires (100 {mu}m) with an Nd:YAG laser. Based on extensive parameter studies, faultless joints were produced. This study deals with the structural changes occurring in the fusion and heat-affected zones, the performance of the joints in static tensile tests and their functional fatigue. It can be shown that NiTi/NiTi joints reach about 75% of the ultimate tensile strength of pure NiTi wires. For welding NiTi to steel, no interlayer was used. The dissimilar NiTi/steel joints provide a bonding strength in the fusion and heat-affected zones higher than the plateau stress level. NiTi/steel joints of thin wires, as a new aspect, enable the possibility to benefit from the pseudoelastic properties of the NiTi component.

  5. Effects of Ni vacancy, Ni antisite, Cr and Pt on the third-order elastic constants and mechanical properties of NiAl

    KAUST Repository

    Wu, Shaohua

    2014-12-01

    Effects of Ni vacancy, Ni antisite in Al sublattice, Cr in Al sublattice, Pt in Ni sublattice on the second-order elastic constants (SOECs) and third-order elastic constants (TOECs) of the B2 NiAl have been investigated using the first-principles methods. Lattice constant and the SOECs of NiAl are in good agreement with the previous results. The brittle/ductile transition map based on Pugh ratio G/B and Cauchy pressure Pc shows that Ni antisite, Cr, Pt and pressure can improve the ductility of NiAl, respectively. Ni vacancy and lower pressure can enhance the Vickers hardness Hv of NiAl. The density of states (DOS) and the charge density difference are also used to analysis the effects of vacancy, Ni antisite, Cr and Pt on the mechanical properties of NiAl, and the results are in consistent with the transition map. © 2014 Elsevier Ltd. All rights reserved.

  6. Continuum mechanics simulations of NiO/Ni-YSZ composites during reduction and re-oxidation

    DEFF Research Database (Denmark)

    Pihlatie, Mikko; Frandsen, Henrik Lund; Kaiser, Andreas

    2010-01-01

    expansion, diffusional creep, grain boundary sliding (GBS) and microcracking due to excessive stress. In the Ni/NiO phase, nonelastic strains in terms of diffusional and power law creep were implemented, and additionally for NiO deformation due to microcracking and/or pseudoplasticity. Semi...

  7. Preparation and characterization of Cu(111)-Ni and Cu(110)-Ni surface alloys

    NARCIS (Netherlands)

    Geus, John W.; Mesters, C.M.A.M.; Wermer, G.; Gijzeman, O.L.J.

    1984-01-01

    The interaction of Ni(CO)4/CO gas mixtures with Cu(111) and Cu(110) single crystal surfaces has been studied with ellipsometry. Auger electron spectroscopy, LEED and argon ion depth profiling. At room temperature Ni atoms with some CO ligands remain at the surface. The amount of Ni that can be

  8. Contexto Familiar: Diferencias Conductuales entre Niños y Niñas

    Directory of Open Access Journals (Sweden)

    María Aurelia Ramírez Castillo

    2005-01-01

    Full Text Available En este trabajo se investigan las diferencias por género en problemas de conducta. En una muestra de 200 sujetos (niños y niñas en tre 5 y 18 años de Granada (España, los resultados concluyen que los niños tienen más problemas de conducta delictiva que las niñas. Cuando existen conflictos matrimoniales y prácticas de crianza negativas, de nuevo los niños tienen más problemas externos que las niñas. En este trabajo se investigan las diferencias por género en problemas de conducta. En una muestra de 200 sujetos (niños y niñas en tre 5 y 18 años de Granada (España, los resultados concluyen que los niños tienen más problemas de conducta delictiva que las niñas. Cuando existen conflictos matrimoniales y prácticas de crianza negativas, de nuevo los niños tienen más problemas externos que las niñas.

  9. Structure-activity relations for Ni-containing zeolites during NO reduction. II. Role of the chemical state of Ni

    NARCIS (Netherlands)

    Mosqueda Jimenez, B.I.; Jentys, A.; Seshan, Kulathuiyer; Lercher, J.A.

    2003-01-01

    The influence of the metal in Ni-containing zeolites used as catalysts for the reduction of NO with propane and propene was studied. In the fresh catalysts, Ni is located in ion exchange positions for Ni/MOR, Ni/ZSM-5, and Ni/MCM-22. The formation of carbonaceous deposits, the removal of Al from

  10. Analysis for probability of irradiance fluctuation; Nissha hendo kakuritsu no bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Minowa, J.; Kurokawa, K. [Tokyo University of Agriculture and Technology, Tokyo (Japan); Otani, K.; Sakuta, K. [Electrochemical Laboratory, Tsukuba (Japan)

    1996-10-27

    Distribution of probabilities of solar radiation fluctuation was examined to learn the fluctuation in photovoltaic power generation efficiency for the purpose of improving on the generation system. The measuring setup comprised one base station and nine terminal stations. The terminal stations were arrayed in lattice so that a 4km{times}4km-large area would be covered. The standard deviation in solar radiation fluctuation at an observation spot ANNE stayed constant at approximately 0.1kW/m{sup 2} at all observation hours. In the vicinity of a clearness index range of 0.5-0.6 (a higher index showing a clearer weather) in the daytime, the index fluctuated very much, predicting a half-clear sky with scattered cloud. In the range of 0.2-0.3, fluctuation was small. In the range of 0.6-0.7, fluctuation was small and solar radiation was stable under the clear sky. The scope of fluctuation in the areal average is smaller than that in the average at each of the terminal stations, which is explained by the even-out effect. This means that, if multiple PV systems concentratedly introduced into one region are appropriately coordinated, the outputs from the individual PV systems that are naturally inconsistent are evened out and that the reliability of the network as a whole is consequently enhanced. 5 refs., 7 figs., 1 tab.

  11. Measurement of carbon dioxid and the fluctuation of its concentration. Nisankatanso no keisoku to nodo hendo

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, M. (Tohoku Univ., Sendai (Japan). Faculty of Science)

    1990-07-10

    Accompanied with the issue of the global waming, it has become very important to measure the concentrations of the gases which bring about greenhouse effects in order to find out the annual increases and the concentration distributions of the gases. This report explains the measuring method, fluctuation and circulation of CO {sub 2} which is especially important among the gases which bring about greenhouse effects. The standard measuring instrument used is a nondispersive infrared analyzer (NDIR). This analyzer converts the luminosity difference of the infrared ray to electric generating power. As this is relative measurement with standard gas, the adjustment of carrier gas and standard gas is very important for the accuracy. The nondispersive infrared analyzer of highest accuracy in the world uses dry air as carrier gas, and its relative accuracy is 0.01ppmv (ppmv is volume parts per million) and its absolute accuracy is 0.1ppmv. It is possible to analyze the factors of nature and the factors of human activities from the distribution of CO {sub 2} concentration, its daily change, seasonal fluctuation and long-term trends. 10 refs., 8 figs.

  12. Morphological control of Ni/NiO core/shell nanoparticles and production of hollow NiO nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, Nitin [University of Alabama, Department of Metallurgical and Materials Engineering, Center for Materials for Information Technology (MINT) (United States); Claypoole, Leslie [Fairmont State University (United States); Bachas, Leonidas G., E-mail: bachas@uky.ed [University of Kentucky, Department of Chemistry (United States)

    2010-10-15

    Chemical synthesis coupled with a microwave irradiation process allowed for the control of size (6-40 nm), shape, and shell thickness of Ni/NiO core/shell nanoparticles. In this unique synthetic route, the size of Ni nanoparticles (NiNPs) was strongly influenced by the nickel salt-to-stabilizer ratio and the amount of the stabilizer. Interestingly, it was observed that the shape of the nanoparticles was altered by varying the reaction time, where longer reaction times resulted in annealing effects and rupture of the stabilizer micelle leading to distinct shapes of Ni/NiO core/shell nanostructures. Product cooling rate was another important parameter identified in this study that not only affected the shape, but also the crystal structure of the core/shell nanoparticles. In addition, a simple and cost-effective method of microwave irradiation of NiNPs led to the formation of distinctly shaped hollow NiO nanoparticles. These high surface area core/shell nanoparticles with well-controlled morphologies are important and can lead to significant advancement in the design of improved fuel cells, electrochromic display devices, and catalysis systems.

  13. .';.:NI~

    African Journals Online (AJOL)

    nag was die terugtog van die Skotte, oor die woestyn, vir myle sigbaar soos die een ou krok na die ander opgegaan het in ligte laaie. Geen wonder dat luisteraars die volgende aand oor. Zeesenradio gehoor het hoe 8 Leer verslaan is dat hulle, in hulle dolIe vaart na die Delta, besig was om hulle voertuie te verband.

  14. Thermal neutron capture γ-ray spectroscopy of59Ni and61Ni

    Science.gov (United States)

    Harder, A.; Michaelsen, S.; Lieb, K. P.; Williams, A. P.

    1993-06-01

    The γ-radiation emitted after thermal neutron capture in isotopically enriched58Ni and60Ni was measured at the ILL high flux reactor by means of Ge/NaI detectors operated in Compton suppression and pair spectrometer mode. The neutron binding energies were determined as B n (59Ni)=8999.15(23) keV and Bn(61Ni)=7820.07(20) keV; some 95% of the total γ-ray fluxes through59,61Ni were assigned. The γ-ray strength functions of the primary transitions and the level densities are discussed.

  15. Who is El Niño?

    Science.gov (United States)

    Philander, S. George

    It is a curious story, about a phenomenon we first welcomed as a blessing but now view with dismay, if not horror [Philander, 1998]. We named it El Niño for the child Jesus, provided it with relatives—La Niña and ENSO—and are devoting innumerable studies to the description and idealization of this family. These scriptures provide such a broad spectrum of historical, cultural, and scientific perspectives that there is now confusion about the identity of El Niño. Trenberth [1997] summarizes the situation as follows.The atmospheric component tied to El Niño is termed the “Southern Oscillation.” Scientists often call the phenomenon where the atmosphere and ocean collaborate ENSO, short for El Niño-Southern Oscillation. El Niño then corresponds to the warm phase of ENSO. The opposite “La Niña” (“the girl” in Spanish) phase consists of a basinwide cooling of the tropical Pacific and thus the cold phase of ENSO. However, for the public, the term for the whole phenomenon is “El Niño.”

  16. nière's Disease

    Science.gov (United States)

    ... disease. Why do people get Ménière’s disease? Many theories exist about what happens to cause Ménière’s disease, ... changes. Some people claim that caffeine, chocolate, and alcohol make their symptoms worse and either avoid or ...

  17. Capture of Hydrogen Using ZrNi

    Science.gov (United States)

    Patton, Lisa; Wales, Joshua; Lynch, David; Parrish, Clyde

    2005-01-01

    Water, as ice, is thought to reside in craters at the lunar poles along with CH4 and H2 . A proposed robotic mission for 2012 will utilize metal/metal hydrides for H2 recovery. Specifications are 99% capture of H2 initially at 5 bar and 100C (or greater), and degassing completely at 300C. Of 47-systems examined using the van't Hoff equation, 4 systems, Mg/MgH2, Mg2Ni/Mg2NiH4, ZrNi/ZrNiH2.8, and Pd/PdH0.77, were considered likely candidates for further examination. It is essential, when selecting a system, to also examine questions regarding activation, kinetics, cyclic stability, and gas impurity effects. After considering those issues, ZrN1 was selected as the most promising candidate, as it is easily activated and rapidly forms ZrNiH 2.8 . In addition, it resists oxide poisoning by CO2, and H2O, while some oxidation by O2 is recommended for improved activation . The presence of hydrogen in the as received Zr-Ni alloy from Alfa Aesar posed additional technical problems. X-ray diffraction of the Zr-Ni powder (-325 mesh), with a Zr:Ni wt% ratio of 70:30, was found to consist of ZrH2, ZrNiH2.8, and ZrNi. ZrH2 in the alloy presented the risk that after degassing that both Zr and ZrNi would be present, and thus lead to erroneous results regarding the reactivity of ZrNi with H2 . Fortunately, ZrH2 is a highly stable hydride that does not degas H2 to any significant extent at temperatures below 300C. Based on equilibrium calculations for the decomposition of ZrH2, only 1 millionth of the hydride decomposed at 300C under a N2 atmosphere flowing at 25 ccm for 64 hours, the longest time for pretreatment employed in the investigation. It was possible, from the X-ray results and knowledge of the Zr:Ni ratio, to compute the composition of a pretreated specimen as being 76 wt% ZrNi and the balance ZrH2.

  18. Water dissociation on Ni(100), Ni(110), and Ni(111) surfaces: Reaction path approach to mode selectivity.

    Science.gov (United States)

    Seenivasan, H; Jackson, Bret; Tiwari, Ashwani K

    2017-02-21

    A comparative study of mode-selectivity of water dissociation on Ni(100), Ni(110), and Ni(111) surfaces is performed at the same level of theory using a fully quantum approach based on the reaction path Hamiltonian. Calculations show that the barrier to water dissociation on the Ni(110) surface is significantly lower compared to its close-packed counterparts. Transition states for this reaction on all three surfaces involve the elongation of one of the O-H bonds. A significant decrease in the symmetric stretching and bending mode frequencies near the transition state is observed in all three cases and in the vibrational adiabatic approximation, excitation of these softened modes results in a significant enhancement in reactivity. Inclusion of non-adiabatic couplings between modes results in the asymmetric stretching mode showing a similar enhancement of reactivity as the symmetric stretching mode. Dissociation probabilities calculated at a surface temperature of 300 K showed higher reactivity at lower collision energies compared to that of the static surface case, underlining the importance of lattice motion in enhancing reactivity. Mode selective behavior is similar on all the surfaces. Molecules with one-quantum of vibrational excitation in the symmetric stretch, at lower energies (up to ∼0.45 eV), are more reactive on Ni(110) than the Ni(100) and Ni(111) surfaces. However, the dissociation probabilities approach saturation on all the surfaces at higher incident energy values. Overall, Ni(110) is found to be highly reactive toward water dissociation among the low-index nickel surfaces owing to a low reaction barrier resulting from the openness and corrugation of the surface. These results show that the mode-selective behavior does not vary with different crystal facets of Ni qualitatively, but there is a significant quantitative effect.

  19. The Ni-YSZ interface

    DEFF Research Database (Denmark)

    Jensen, Karin Vels

    the samples with impure nickel electrodes showed an initial increase toward a high constant polarisation resistance, whereas the samples with pure nickel electrodes showed a considerable decrease to a low constant polarisation resistance with time. For both types of nickel the polarisation resistance dropped......The anode/electrolyte interface in solid oxide fuel cells (SOFC) is known to cause electrical losses. Geometrically simple Ni/yttria-stabilised zirconia (YSZ) interfaces were examined to gain information on the structural and chemical changes occurring during experiments at 1000°C in an atmosphere...... of 97% H2/3% H2O. Electrochemical impedance spectroscopy at open circuit voltage (OCV) and at anodic and cathodic polarisations (100 mV) was performed. A correlation of the electrical data with the structure development and the chemical composition was attempted. Nickel wires with different impurity...

  20. Niño maltratado

    Directory of Open Access Journals (Sweden)

    Ana Ivis Crespo Barrios

    1996-12-01

    Full Text Available Se presentan 200 niños maltratados que acuden al Hospital Pediátrico Docente "Juan Manuel Márquez" en el período comprendido de diciembre de 1990 a enero de 1992; éstos fueron seleccionados teniendo en cuenta los criterios de maltrato, y era el objetivo fundamental del estudio conocer cómo se comporta en nuestro medio. En los resultados se muestra que la forma más frecuente fue el tipo no intencional; la ingestión de tóxicos fue la forma de negligencia física más frecuente dentro del maltrato no intencional, ésta es más usual en los niños menores de 5 años; los trastornos psiquiátricos y el alcoholismo son favorecedores del maltrato intencional, la madre es la que más maltrata; la mortalidad por esta causa no fue elevada (5 fallecidos y los criterios de riesgo de maltrato tienen utilidad para su identificación.200 mistreated children who were seen at the "Juan Manual Márquez" Pediatric Teaching Hospital from December, 1990 to January, 1992, are presented. These patients were selected taking into consideration the abuse criteria. The main objective of this paper was to know how these criteria behave in our enviroment. According to the results, the most common form was the non-intentional type. The ingestion of toxic agents was the most frequent form of physical neglect within the non-intentional mistreatment, and it is the most usual among children under 5. Psychiatric disorders and alcoholism favor the intentional mistreatment, and the mother mistreats the most. Mortality due to this cause was not high (5 deaths, and the abuse risk criteria are useful for its identification.

  1. Nonenzymatic Glucose Sensor Based on In Situ Reduction of Ni/NiO-Graphene Nanocomposite

    Directory of Open Access Journals (Sweden)

    Xiaohui Zhang

    2016-10-01

    Full Text Available Ni/NiO nanoflower modified reduced graphene oxide (rGO nanocomposite (Ni/NiO-rGO was introduced to screen printed electrode (SPE for the construction of a nonenzymatic electrochemical glucose biosensor. The Ni/NiO-rGO nanocomposite was synthesized by an in situ reduction process. Graphene oxide (GO hybrid Nafion sheets first chemical adsorbed Ni ions and assembled on the SPE. Subsequently, GO and Ni ions were reduced by hydrazine hydrate. The electrochemical properties of such a Ni/NiO-rGO modified SPE were carefully investigated. It showed a high activity for electrocatalytic oxidation of glucose in alkaline medium. The proposed nonenzymatic sensor can be utilized for quantification of glucose with a wide linear range from 29.9 μM to 6.44 mM (R = 0.9937 with a low detection limit of 1.8 μM (S/N = 3 and a high sensitivity of 1997 μA/mM∙cm−2. It also exhibited good reproducibility as well as high selectivity.

  2. Asymmetry of inter-El Niño and -La Niña diversity

    Science.gov (United States)

    Kim, S.; Kug, J. S.

    2016-12-01

    Over the North Pacific, there is a distinctive asymmetry of inter-El Niño and -La Niña diversity in atmospheric teleconnection patterns, indicating a strong diversity during La Niña events. Recent studies suggested that the typical patterns of the extratopical teleconnections associated with El Niño-Southern Oscillation (ENSO) are predominantly explained by the relative roles of the equatorial central Pacific (CP) and western North Pacific (WNP) precipitation anomalies. We find that the diversity of WNP precipitation anomalies is greater during La Niña events than during El Niño events. It also implies that the diversity of WNP precipitation anomalies during La Niña events is responsible for the diversity in the extratropical teleconnection. Since the relationship of anomalous sea surface temperature (SST) to precipitation is quite sensitive for SST in the range of 27-28°C, the WNP precipitation differences located over the warm pool among La Niña events lead to considerable teleconnection changes. In addition, we find here that the CMIP5 models well simulate the overall diversity in the tropical precipitation and extratropical teleconnection patterns during La Niña events, but it fails to reproduce a detailed pattern difference of atmospheric teleconnection in inter-La Niña events.

  3. Engineering NiS/Ni2P Heterostructures for Efficient Electrocatalytic Water Splitting.

    Science.gov (United States)

    Xiao, Xin; Huang, Dekang; Fu, Yongqing; Wen, Ming; Jiang, Xingxing; Lv, Xiaowei; Li, Man; Gao, Lin; Liu, Shuangshuang; Wang, Mingkui; Zhao, Chuan; Shen, Yan

    2018-01-23

    Developing high-active and low-cost bifunctional materials for catalyzing the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) holds a pivotal role in water splitting. Therefore, we present a new strategy to form NiS/Ni2P heterostructures. The as-obtained NiS/Ni2P/carbon cloth (CC) requires overpotentials of 111 mV for the HER and 265 mV for the OER to reach a current density of 20 mA cm-2, outperforming their counterparts such as NiS and Ni2P under the same conditions. Additionally, the NiS/Ni2P/CC electrode requires a 1.67 V cell voltage to deliver 10 mA cm-2 in a two-electrode electrolysis system, which is comparable to the cell using the benchmark Pt/C||RuO2 electrode. Detailed characterizations reveal that strong electronic interactions between NiS and Ni2P, abundant active sites, and smaller charge-transfer resistance contribute to the improved HER and OER activity.

  4. Study of the central collisions in the reactions Ni + Al and Ni + Ni at 28 A.MeV; Etude des collisions centrales dans les reactions Ni + Al et Ni + Ni a 28 A.MeV

    Energy Technology Data Exchange (ETDEWEB)

    Lebreton, L.

    1995-12-01

    The work is in characterisation of mechanisms in the energy range of onset of multifragmentation (excitation energy of composed nucleus around 4 - 5 AMeV). This work focused on an experiment performed at the SARA facility, in Grenoble, using the AMPHORA multi detection array. I have been particularly interested in central collisions in the Ni + Al and Ni + Ni systems. The possibility to detect complete events for Ni + Al, and quasi-complete events for the Ni + Ni case, is the reason of this choice. Furthermore Ni + Ni presents the interest of a symmetrical system, for which the excitation energy per nucleon is maximum. The study of these reactions has been focused on the quasi-complete events (events for which at least 80 % of the total charge has been detected). Heavy ions produced in peripheral collisions are very likely emitted along the beam line or stopped in the plastic detectors, energy thresholds are too high for the quasi-target products detection, consequently by requiring complete or quasi-complete measurement of the total charge, we are able to detect mostly central events. The knowledge of informations like charge, energy or detection angles allows to isolate the source(s) and to reconstruct the size and the excitation energy of the source(s). Comparisons with simulations like sequential emission (GEMINI code), very deep inelastic collision or instantaneous emission (Berliner code) allows to characterise the first stage of the collision (binary collisions or central collisions) and the type of deexcitation of the source(s). Some calculations was also performed with the statistical model code MODGAN. Indeed azimuthal correlations seem to be a good tool in getting more information about involved reaction mechanisms. Comparisons with MODGAN provide information about angular momentum of the source and time delay between emissions of the two particles (separation between sequential or instantaneous process). (author). 69 refs.

  5. Ääniä tiloissa

    OpenAIRE

    Rehn, Nicolas

    2014-01-01

    Opinnäytetyössäni esittelen keväällä 2013 Pop & Jazz Konservatorion lounasravintolan WC:ssä toteuttamani liveinstallaation Ääniä tiloissa. Analysoin teokseni kautta taiteen ja musiikin tekemisen motiiveja ja symboliikkaa, sekä tilan funktiota paikkana jossa toteuttaa musiikkia ja taidetta. Tavoitteenani opinnäytetyössäni oli toteuttaa performatiivinen esitys joka on vahvasti sidoksissa tiettyyn paikkaan, tilaan ja aikaan, ja jonka äänimateriaali saa muotonsa tässä nimenomaisessa tilassa ...

  6. Ni{sub 3}Al aluminide alloys

    Energy Technology Data Exchange (ETDEWEB)

    Liu, C.T.

    1993-10-01

    This paper provides a brief review of the recent progress in research and development of Ni{sub 3}Al and its alloys. Emphasis has been placed on understanding low ductility and brittle fracture of Ni{sub 3}Al alloys at ambient and elevated temperatures. Recent studies have resulted in identifying both intrinsic and extrinsic factors governing the fracture behavior of Ni{sub 3}Al alloys. Parallel efforts on alloy design using physical metallurgy principles have led to properties for structural use. Industrial interest in these alloys is high, and examples of industrial involvement in processing and utilization of these alloys are briefly mentioned.

  7. New developments in Ni/Ti multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, I.; Hoghoj, P. [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France)

    1997-04-01

    It is now 20 years since super-mirrors were first used as a neutron optical element. Since then the field of multilayer neutron-optics has matured with multilayers finding their way to application in many neutron scattering instruments. However, there is still room for progress in terms of multilayer quality, performance and application. Along with work on multilayers for neutron polarisation Ni/Ti super-mirrors have been optimised. The state-of-the-art Ni/Ti super-mirror performance and the results obtained in two neutron-optics applications of Ni/Ti multilayers are presented. (author).

  8. Binary Ni-Nb bulk metallic glasses

    Science.gov (United States)

    Xia, L.; Li, W. H.; Fang, S. S.; Wei, B. C.; Dong, Y. D.

    2006-01-01

    We studied the glass forming ability of Ni-Nb binary alloys and found that some of the alloys can be prepared into bulk metallic glasses by a conventional Cu-mold casting. The best glass former within the compositional range studied is off-eutectic Ni62Nb38 alloy, which is markedly different from those predicted by the multicomponent and deep eutectic rules. The glass formation mechanism for binary Ni-Nb alloys was studied from the thermodynamic point of view and a parameter γ* was proposed to approach the ability of glass formation against crystallization.

  9. Nickel Release, ROS Generation and Toxicity of Ni and NiO Micro- and Nanoparticles.

    Directory of Open Access Journals (Sweden)

    Siiri Latvala

    Full Text Available Occupational exposure to airborne nickel is associated with an elevated risk for respiratory tract diseases including lung cancer. Therefore, the increased production of Ni-containing nanoparticles necessitates a thorough assessment of their physical, chemical, as well as toxicological properties. The aim of this study was to investigate and compare the characteristics of nickel metal (Ni and nickel oxide (NiO particles with a focus on Ni release, reactive oxygen species (ROS generation, cellular uptake, cytotoxicity and genotoxicity. Four Ni-containing particles of both nano-size (Ni-n and NiO-n and micron-size (Ni-m1 and Ni-m2 were tested. The released amount of Ni in solution was notably higher in artificial lysosomal fluid (e.g. 80-100 wt% for metallic Ni than in cell medium after 24h (ca. 1-3 wt% for all particles. Each of the particles was taken up by the cells within 4 h and they remained in the cells to a high extent after 24 h post-incubation. Thus, the high dissolution in ALF appeared not to reflect the particle dissolution in the cells. Ni-m1 showed the most pronounced effect on cell viability after 48 h (alamar blue assay whereas all particles showed increased cytotoxicity in the highest doses (20-40 μg cm2 when assessed by colony forming efficiency (CFE. Interestingly an increased CFE, suggesting higher proliferation, was observed for all particles in low doses (0.1 or 1 μg cm-2. Ni-m1 and NiO-n were the most potent in causing acellular ROS and DNA damage. However, no intracellular ROS was detected for any of the particles. Taken together, micron-sized Ni (Ni-m1 was more reactive and toxic compared to the nano-sized Ni. Furthermore, this study underlines that the low dose effect in terms of increased proliferation observed for all particles should be further investigated in future studies.

  10. Ni nanoparticles prepared by simple chemical method for the synthesis of Ni/NiO-multi-layered graphene by chemical vapor deposition

    Science.gov (United States)

    Ali, Mokhtar; Remalli, Nagarjuna; Gedela, Venkataramana; Padya, Balaji; Jain, Pawan Kumar; Al-Fatesh, Ahmed; Rana, Usman Ali; Srikanth, Vadali V. S. S.

    2017-02-01

    A new chemical method was used to obtain a high yield of nickel nanoparticles (Ni-NPs). The effect of solvent (distilled water, ethylene glycol, and ethanol) and surfactant (oleic acid and polyvinyl pyrrolidinone) on the morphology and crystallinity of the synthesized Ni-NPs has been investigated. The experimental results revealed that among the solvents mentioned above, ethanol gives the best results in terms of complete reduction, controlled morphology and size distribution of Ni-NPs. The surfactants played an important role in impeding the agglomeration and surface oxidation of Ni-NPs. The surfactants also affected the morphology of the Ni-NPs. The synthesized Ni-NPs are found to be quite stable in air. The best of the synthesized Ni-NPs were effectively used as catalysts for the synthesis of Ni/NiO-multi-layered graphene using catalytic chemical vapor deposition technique.

  11. Synthesis of Supported NiPt Bimetallic Nanoparticles, Methods for Controlling the Surface Coverage of Ni Nanoparticles With Pt, Methods Of Making NiPt Multilayer Core-Shell Structures and Application of the Supported Catalysts for CO2 Reforming

    KAUST Repository

    Li, Lidong

    2015-06-25

    Embodiments of the present disclosure provide for supported Ni/Pt bimetallic nanoparticles, compositions including supported NiPt nanoparticles, methods of making supported NiPt nanoparticles, methods of using supported NiPt nanoparticles, and the like.

  12. Fine Structure in Multi-Phase Zr8Ni21-Zr7Ni10-Zr2Ni7 Alloy Revealed by Transmission Electron Microscope

    Directory of Open Access Journals (Sweden)

    Haoting Shen

    2015-07-01

    Full Text Available The microstructure of an annealed alloy with a Zr8Ni21 composition was studied by both scanning electron microscopy (SEM and transmission electron microscopy (TEM. The presence of three phases, Zr8Ni21, Zr2Ni7, and Zr7Ni10, was confirmed by SEM/X-ray energy dispersive spectroscopy compositional mapping and TEM electron diffraction. Distribution of the phases and their morphology can be linked to a multi-phase structure formed by a sequence of reactions: (1 L → Zr2Ni7 + L’; (2 peritectic Zr2Ni7 + L’ → Zr2Ni7 + Zr8Ni21 + L”; (3 eutectic L” → Zr8Ni21 + Zr7Ni10. The effect of annealing at 960 °C, which was intended to convert a cast structure into a single-phase Zr8Ni21 structure, was only moderate and the resulting alloy was still multi-phased. TEM and crystallographic analysis of the Zr2Ni7 phase show a high density of planar (001 defects that were explained as low-energy boundaries between rotational variants and stacking faults. The crystallographic features arise from the pseudo-hexagonal structure of Zr2Ni7. This highly defective Zr2Ni7 phase was identified as the source of the broad X-ray diffraction peaks at around 38.4° and 44.6° when a Cu-K was used as the radiation source.

  13. Incorporation of alumina particles into reactively sintered Ni{sub 3}Al; Hanno shoketsu ni yoru Ni{sub 3}Al eno alumina no fukugoka

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, M.; Ochiai, S.; Arai, T. [Teikyo Univ. of Science and Tech., Yamanashi (Japan); Sakamoto, Y. [Teikyo Univ. of Science and Tech., Yamanashi (Japan)]|[NIKKOSHI Co. Ltd., Tokyo (Japan); Koyama, M. [Japan Space Utilization Promotion Center, Tokyo (Japan)

    1998-08-15

    The Ni3Al having the structure of L1{sub 2} is attracting the attention of the people. As methods for preparing it, the reactive sintering method according to which Ni powders and Al powders are mixed first and then reacted at 700 degC to prepare the Ni2Al, and the combustion composition method are expected as the hopeful method. In this study, several processes for composing alumina while preparing the Ni3Al by reactively sintering Ni powders and Al powders, are compared. While dispersing alumina powders into Ni powders beforehand by mechanical dispersing (MD), the Ni3Al can be produced under the conditions as they are. As another method for producing the Ni3Al according to which NiO powders are mixed into Ni powders to oxidize surfaces of the Ni powders and then they react with the Al powders, the reactive sintering of the Ni3Al and the alumina generation by the thermit reaction progress simultaneously, but dispersion of the alumina is the worst and the void is too much. As for the method according to which the NiO powders in the Ni powders are mechanically dispersed and then reacted with Al powders, the resultant reactions hardly occur. 9 refs., 4 figs.

  14. An Ultrastable and High-Performance Flexible Fiber-Shaped Ni-Zn Battery based on a Ni-NiO Heterostructured Nanosheet Cathode.

    Science.gov (United States)

    Zeng, Yinxiang; Meng, Yue; Lai, Zhengzhe; Zhang, Xiyue; Yu, Minghao; Fang, Pingping; Wu, Mingmei; Tong, Yexiang; Lu, Xihong

    2017-11-01

    Currently, the main bottleneck for the widespread application of Ni-Zn batteries is their poor cycling stability as a result of the irreversibility of the Ni-based cathode and dendrite formation of the Zn anode during the charging-discharging processes. Herein, a highly rechargeable, flexible, fiber-shaped Ni-Zn battery with impressive electrochemical performance is rationally demonstrated by employing Ni-NiO heterostructured nanosheets as the cathode. Benefiting from the improved conductivity and enhanced electroactivity of the Ni-NiO heterojunction nanosheet cathode, the as-fabricated fiber-shaped Ni-NiO//Zn battery displays high capacity and admirable rate capability. More importantly, this Ni-NiO//Zn battery shows unprecedented cyclic durability both in aqueous (96.6% capacity retention after 10 000 cycles) and polymer (almost no capacity attenuation after 10 000 cycles at 22.2 A g-1 ) electrolytes. Moreover, a peak energy density of 6.6 µWh cm-2 , together with a remarkable power density of 20.2 mW cm-2 , is achieved by the flexible quasi-solid-state fiber-shaped Ni-NiO//Zn battery, outperforming most reported fiber-shaped energy-storage devices. Such a novel concept of a fiber-shaped Ni-Zn battery with impressive stability will greatly enrich the flexible energy-storage technologies for future portable/wearable electronic applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Investigation of Characteristics of Sprayed Ni-Cr and Ni-Cr-Wc Coatings

    Directory of Open Access Journals (Sweden)

    Ovidijus Jarašūnas

    2017-01-01

    Full Text Available The article deals with the flame sprayed Ni-Cr and Ni-Cr-WC coatings on construction S235 steel substrates. Before spraying, the surfaces of substrates were treated mechanically. Using the different chemical composition of Ni-Cr and Ni-Cr-WC spraying powder and additional substrate heating till 250–290 °C, were sprayed coatings. The microstructure, porosity, hardness, elastic modulus, wear resistance of the Ni-Cr and Ni-Cr-WC coatings were investigated in the work. The influence of the chemical composition and WC content of the coatings on the various physical and tribological properties of the coatings were evaluated. Also the dependence of these coatings characteristics was investigated.

  16. Structural analysis of Ni/NiO-water interface using X-ray reflectivity

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Jin; Kim, Seung Hyun; Kim, Ji Hyun [Ulsan National Institute of Science and technology, Ulsan (Korea, Republic of); Bahn, Chi Bum [Argonne National Laboratory, Illinois (United States)

    2013-10-15

    These test revealed the epitaxial relationship between Ni substrate and the oxide layer as well as those structures. However, still the resolution of the initial structural data of interface between water and pre oxidized Ni(110) surface is not clear. Therefore, the objective in this study was to obtain detailed structural data between pre-oxidized Ni(110) and water interfaces to investigate the mechanism of growth the passive film formed on Ni(110) by In-situ high energy X-ray reflectivity study and simulated atomistic model. The surface treatment procedure to increase the surface crystallinity was developed to surface x-ray reflectivity measurement. The CTR data shows the surface pre-treatment procedure developed for Ni(110) was suitable for the surface X-ray study. Synchrotron X-ray experiments and analyses will be continued to identify the surface interface between Ni(110), water, and solution contained lead.

  17. Contexto Familiar: Diferencias Conductuales entre Niños y Niñas

    OpenAIRE

    María Aurelia Ramírez Castillo

    2005-01-01

    En este trabajo se investigan las diferencias por género en problemas de conducta. En una muestra de 200 sujetos (niños y niñas) en tre 5 y 18 años de Granada (España), los resultados concluyen que los niños tienen más problemas de conducta delictiva que las niñas. Cuando existen conflictos matrimoniales y prácticas de crianza negativas, de nuevo los niños tienen más problemas externos que las niñas. En este trabajo se investigan las diferencias por género en problemas de condu...

  18. Ni Mineralization and PGE Characterization in the Kabanga and ...

    African Journals Online (AJOL)

    ... indicate that the Luhuma is also potential for Ni-Cu sulfide deposits particularly on drill holes LUH05 and LUH13 where these samples were taken. In other words, if TiO2 increases then Ni-Cu sulfide increases and hence the potential for Ni-Cu mineralization. Key words: Tanzania, Kabanga, Luhuma, PGE, Ni-Cu sulfides ...

  19. Crystallographic Orientation Effect on Electromigration in Ni-Sn Microbump

    Science.gov (United States)

    Huang, Yi-Ting; Chen, Chih-Hao; Chakroborty, Subhendu; Wu, Albert T.

    2017-09-01

    This article addresses the reliability challenges regarding electromigration in developing three-dimensional integrated circuits (3D-ICs). The line-type sandwich structure of Ni/Sn3.5Ag(15 μm)/Ni was used to simulate microbumps to examine the reliability of electromigration in 3D-IC technology. The solder strip of Ni/Sn3.5Ag(15 μm)/Ni was stressed with a current density of 1.0 × 104 A/cm2 at 150°C. The current stressing enhanced the reaction between the solder and Ni to form Ni3Sn4, which occupied the entire joint and transformed into a Ni/Ni3Sn4/Ni structure when the solder was completely consumed. Electron backscatter diffraction was used to analyze the crystallographic characteristics of Sn and Ni3Sn4 as related to the electromigration effect. The results indicated that the crystallographic orientation of Sn plays a significant role in the Ni/Sn3.5Ag/Ni, whereas the orientation of Ni3Sn4 is the dominant factor of diffusion behavior in the Ni/Ni3Sn4/Ni.

  20. Site occupancy of Fe in ternary Ni 75-x

    Indian Academy of Sciences (India)

    The results of a detailed structural and magnetic study clearly indicate that regardless of the thermal history of the samples, Fe has a strong preference for the Ni sites in Ni-poor (non-stoichiometric) Ni75Al25 alloys. Fe substitution has a profound effect on the nature of magnetism in Ni75Al25.

  1. Synthesis of stochastic open cell Ni-based foams

    Energy Technology Data Exchange (ETDEWEB)

    Queheillalt, Douglas T.; Katsumura, Yasushi; Wadley, Haydn N.G

    2004-02-15

    Open cell, stochastic Ni-based foams have been synthesized on carbon foam templates by transient liquid phase bonding nickel based superalloy (Ni-21Cr-9Mo-4Nb) and Ni-25Cr-10P powders. The mechanical properties of these Ni-based foams were similar to those of other lower temperature metal foams of similar topology.

  2. Studies on the valence electronic structure of Fe and Ni in Fe Ni ...

    Indian Academy of Sciences (India)

    -to- X-ray intensity ratios of Fe and Ni in pure metals and in FeNi1- alloys ( = 0.20, 0.50, 0.58) exhibiting similar crystalline structure have been measured following excitation by 59.54 keV -rays from a 241Am point source, to understand as to why the properties of permalloy Fe0.2Ni0.8 is distinct from other alloy ...

  3. Directional Solidification and Mechanical Properties of NiAl-NiAlTa Alloys

    Science.gov (United States)

    Johnson, D. R.; Chen, X. F.; Oliver, B. F.; Noebe, R. D.; Whittenberger, J. D.

    1995-01-01

    Directional solidification of eutectic alloys is a promising technique for producing in-situ composite materials exhibiting a balance of properties. Consequently, the microstructure, creep strength and fracture toughness of directionally solidified NiAl-NiAlTa alloys were investigated. Directional solidification was performed by containerless processing techniques to minimize alloy contamination. The eutectic composition was found to be NiAl-15.5 at% Ta and well-aligned microstructures were produced at this composition. A near-eutectic alloy of NiAl-14.5Ta was also investigated. Directional solidification of the near-eutectic composition resulted in microstructures consisting of NiAl dendrites surrounded by aligned eutectic regions. The off-eutectic alloy exhibited promising compressive creep strengths compared to other NiAl-based intermetallics, while preliminary testing indicated that the eutectic alloy was competitive with Ni-base single crystal superalloys. The room temperature toughness of these two-phase alloys was similar to that of polycrystalline NiAl even with the presence of the brittle Laves phase NiAlTa.

  4. Modeling and simulation of NiO dissolution and Ni deposition in molten carbonate fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Suk Woo; Choi, Hyung-Joon; Lim, Tae Hoon [Korea Institute of Science & Technology, Seoul (Korea, Republic of)] [and others

    1996-12-31

    Dissolution of NiO cathode into the electrolyte matrix is an important phenomena limiting the lifetime of molten carbonate fuel cell (MCFC). The dissolved nickel diffuses into the matrix and is reduced by dissolved hydrogen leading to the formation of metallic nickel films in the pores of the matrix. The growth of Ni films in the electrolyte matrix during the continuous cell operation results eventually in shorting between cathode and anode. Various mathematical and empirical models have been developed to describe the NiO dissolution and Ni deposition processes, and these models have some success in estimating the lifetime of MCFC by correlating the amount of Ni deposited in the matrix with shorting time. Since the exact mechanism of Ni deposition was not well understood, deposition reaction was assumed to be very fast in most of the models and the Ni deposition region was limited around a point in the matrix. In fact, formation of Ni films takes place in a rather broad region in the matrix, the location and thickness of the film depending on operating conditions as well as matrix properties. In this study, we assumed simple reaction kinetics for Ni deposition and developed a mathematical model to get the distribution of nickel in the matrix.

  5. Metallic Ni3 P/Ni Co-Catalyst To Enhance Photocatalytic Hydrogen Evolution.

    Science.gov (United States)

    Zhao, Jun Jie; Liu, Peng Fei; Wang, Yu Lei; Li, Yu Hang; Zu, Meng Yang; Wang, Chong Wu; Wang, Xue Lu; Fang, Li Jun; Zeng, Hui Dan; Yang, Hua Gui

    2017-11-27

    Metallic Ni3 P/Ni can be used as a co-catalyst to replace noble metal Pt for efficient photocatalytic hydrogen evolution, due to its excellent trapping-electron ability. The applications of metallic Ni3 P/Ni co-catalyst on CdS, Zn0.5 Cd0.5 S, TiO2 (Degussa P25) and g-C3 N4 are further confirmed, indicating its versatile applicability nature like Pt. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Actitudes afectivas hacia niños y niñas con necesidades educativas especiales

    OpenAIRE

    Cárdenas Leitón, Helvetia

    2013-01-01

    En este artículo se analizan las actitudes afectivas de los compañeros de clase hacia niños y niñas con necesidades educativas especiales, integrados en el sistema de educación regular. Se parte de una investigación cualitativa realizada en cuatro secciones de I y II Ciclos de la Enseñanza General Básica, en Escuelas Urbano Marginales, donde se encontraban niños con necesidades educativas especiales. Se encontró que el tipo de relaciones que se suscitan con los niños integrados, están marcada...

  7. Niños y Violencia

    OpenAIRE

    International Child Development Centre

    1997-01-01

    Este Innocenti Digest explora la violencia de los niños y hacia los niños, usando el marco de la Convención de los Derechos del Niño de las Naciones Unidas. Se centra en la violencia interpersonal, tanto intrafamiliar como extrafamiliar. Se incluye el abuso sexual y la explotación ya que a pesar de no implicar obligatoriamente violencia o coerción, la mayor parte de la evidencia demuestra su efectos dañinos tanto físicos como psicológicos. También se discute la implicación de los niños en los...

  8. Ni adsorption and Ni-Al LDH precipitation in a sandy aquifer: An experimental and mechanistic modeling study

    NARCIS (Netherlands)

    Regelink, I.C.; Temminghoff, E.J.M.

    2011-01-01

    Mining activities and industries have created nickel (Ni) contaminations in many parts of the world. The objective of this study is to increase our understanding of Ni adsorption and Nickel-Aluminium Layered Double Hydroxide (Ni-Al LDH) precipitation to reduce Ni mobility in a sandy soil aquifer. At

  9. Consequences of Surface Oxophilicity of Ni, Ni-Co, and Co Clusters on Methane Activation.

    Science.gov (United States)

    Tu, Weifeng; Ghoussoub, Mireille; Singh, Chandra Veer; Chin, Ya-Huei Cathy

    2017-05-24

    This study describes a new C-H bond activation pathway during CH4-CO2 reactions on oxophilic Ni-Co and Co clusters, unlike those established previously on Ni clusters. The initial C-H bond activation remains as the sole kinetically relevant step on Ni-Co, Ni, and Co clusters, but their specific reaction paths vary. On Ni clusters, C-H bond activation occurs via an oxidative addition step that involves a three-center (H3C···*···H)⧧ transition state, during which a Ni-atom inserts into the C-H bond and donates its electron density into the C-H bond's antibonding orbital. Ni-Co clusters are more oxophilic than Ni; thus, their surfaces are covered with oxygen adatoms. An oxygen adatom and a vicinal Co-atom form a metal-oxygen site-pair that cleaves the C-H bond via a σ bond metathesis reaction, during which the Co inserts into the C-H bond while the oxygen abstracts the leaving H-atom in a concerted, four-center (H3C···*···H···O*)⧧ transition state. Similarly, Co clusters also catalyze the σ bond metathesis step, but much less effectively because of their higher oxophilicities, much stronger binding to oxygen, and less effective hydrogen abstraction than Ni-Co clusters. On Ni-Co and Co clusters, the pseudo-first-order rate coefficients are single-valued functions of the CO2-to-CO ratio (or H2O-to-H2 ratio), because this ratio prescribes the oxygen chemical potentials and the relative abundances of metal-oxygen site-pairs through the water-gas shift equilibrium. The direct involvement of reactive oxygen in the kinetically relevant step leads to more effective CH4 turnovers and complete elimination of coke deposition on Ni-Co bimetallic clusters.

  10. Study of thermal threshold and counter-measures for human body in oceanic working environment. 1st Report. Heat balance model and heat storage index; Shonetsu kankyoka no kaiyo sagyo ni okeru netsuteki genkai to onnetsu taisaku ni kansuru kenkyu. 1. Netsu shushi model to onnetsu shisu

    Energy Technology Data Exchange (ETDEWEB)

    Fukuchi, N. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Nakamura, M. [Tokyo Gakugei University, Tokyo (Japan); Murayama, M.

    1996-12-31

    Identification was intended on effects of such thermal factors as metabolic amount, environmental temperature and humidity, and clothing resistance on human body temperatures during works under hot environments. Therefore, measurements were carried out on human skin temperatures, rectum temperatures and humidity inside clothing, while amount of motion, environmental temperature, and clothing are changed in a constant temperature room and under a sun irradiation environment. Furthermore, a heat balance model was prepared, which divides the objects into an outer shell layer whose temperature changes depending on the result of this experiment and into a core having constant temperature characteristics. An equation to derive skin temperatures was introduced from the model. The equation formulated a calculation formula for heat accumulation in human body, which can be used as a hot heat index. Relationship between thermal factors and heat storage amount was investigated to consider a thermal limit for a physical work. An equation to derive skin temperatures was confirmed capable of expressing general change in skin temperatures, being proved by comparison with experiments. Calculation formulas for amount of heat stored in human body were shown capable of expressing influence of different thermal factors, the expression being useful as a hot heat index. Calculating the human body heat storage is very largely affected by effect of sweat to dissipate heat, hence it is necessary to improve the accuracy including that for body temperature adjusting reactions. 17 refs., 17 figs., 5 tabs.

  11. Aerodynamic stability study of a long-span prestressed concrete cable-stayed bridge. Aerodynamic behavior of edge box girder under uniform flow; Chodai PC shachokyo no taifu anteisei ni kansuru kenkyu. Ichiyoryuchu ni okeru edge girder keishiki no kuriki tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Nomura, T. [Obayashi Corp., Tokyo (Japan)

    1999-01-10

    In recent years, the construction of long-span bridges is on the increase. Prestressed concrete cable-stayed bridges are dynamically very efficient structures of relatively low cost that blend in well with the landscape. Maintenance is also easy. Consequently, the adoption of edge box girders for cable-stayed bridges is increasing worldwide, but problems related to the aerodynamic stability of the structure have emerged. The aerodynamic stability of edge box girders for a prestressed concrete cable-stayed bridge was investigated under uniform flow conditions by conducting several wind tunnel experiments. As a result, the section of the bridge deck was optimized to prevent torsional flutter within an angle of attack varying from -5 to +5 degrees. It is therefore possible to guarantee the aerodynamic stability of long-span prestressed concrete cable-stayed bridges. (author)

  12. Survey report for fiscal 1997 on the survey report on the actual state of technical cooperation on industrial technologies by European countries in the South-eastern Asian region; 1997 nendo Tonan Asia chiiki ni okeru Obei shokoku no sangyo gijutsu ni kansuru gijutsu kyoryoku jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The actual state was surveyed on the technical cooperation by European countries in the South-eastern Asian region. The U.S.A. is making research cooperation with Thailand on ethylene molecule structures to enhance productivity in rubber production, France on molecule markers for high production rubber clone selection, and Australia on grain storing and drying methods. For the Philippines, America is giving assistance on management of reproducible resources, France on climate information communications systems for local areas, Australia on grain storing and drying methods, and Germany on waste oil recovery and reutilization, and development of pollution-free energy resources. For Malaysia, the Great Britain is cooperating on building engineering research centers, Australia on search for plant patheology genetic organics available in the Pacific region, and Germany on investigative researches on pollution prevention for tin mines and processing areas, and forestry and plant information systems. With respect to the ASEAN, this paper reports its activities placing importance on biology and electronics engineering, while the organization is taking actions in the areas of foodstuffs, animals, electronics, information and material science, energy exploration, marine and earth physics, and resource development. (NEDO)

  13. Fiscal 1997 survey report. Investigational study on the cascade utilization of thermal energy (cold heat and hot heat) (feasibility study by the off-line system); 1997 nendo chosa hokokusho. Netsu energy (reinetsu to onnetsu) no cascade riyo ni kansuru chosa kenkyu (off-line hoshiki ni yoru feasibility study)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper studied a system to effectively use unused and low-grade thermal energy (cold heat and hot heat) in the Tokyo-Yokohama seaside area. For transportation of thermal energy, the batch transportation, that is, off-line system was discussed which uses insulated tank loaded barges and railroad freight trains. Thermal energy supply sources are 1) 0.3 million kW class thermal power plant, and 2) LNG storage base of 3 million ton/year class. Thermal energy users are Tokyo (Haneda) Airport D.H.C. (District Heating/Cooling Co.), MM 21 D.H.C. and Shin-Kawasaki D.H.C. The cold heat energy supplied to these three is about 1.5 million Mcal/daytimes300 days/year, and the hot heat energy supplied is about 1.33 million Mcal/daytimes150 days/year. Cold heat is obtained from seawater after the LNG vaporization, and hot heat from heat extracted from thermal turbine. Subcooled ice was selected for cold heat medium, and PCM-120A for hot heat medium. For batch transportation, an STL heat storage system is used which transports plastic capsules sealed with heat medium. Oil saving of 62,000 tons/year and CO2 reduction of about 53,000 tons/year can be expected. 85 figs., 98 tabs.

  14. Fundamental sutdy of aluminothermic reduction of niobium oxide and zirconium oxide. 1st Report. ; Production of Nb-Zr alloy by aluminothermic reduction-electron beam refining. Samka niobium oyobi sanka zirconium no aluminium thermit kangen ni kansuru kiso kenkyu. 1. ; Aluminium thermit kangen-denshi beam yokai seirenho ni yoru Nb-Zr Kei gokin no seizo

    Energy Technology Data Exchange (ETDEWEB)

    Uejo, S.; Numa, K. (Nippon Mining Co. Ltd., Tokyo (Japan))

    1991-10-25

    Noting on the Nb{sub 2}O{sub 5} aluminothermic reduction (ATR) regarded as an efficient method of refining Nb, a small ATR experiment was carried out on mixed oxide of Nb{sub 2}O{sub 5} and Nb{sub 2}O{sub 5}/ZnO{sub 2}. A good separation of metal from slag was obtained by means of performing an ATR with the method of heating the entire reaction system or compensating the heat by adding KC10{sub 3} into the material. The Al, Zr and oxygen concentrations in the metal obtained from an ATR method are related with each other. To raise the Zr concentration in the metal, the Al concentration in the metal must be raised. It was found in the ATR of the Nb{sub 2}O{sub 5}/ZrO{sub 2} mixed oxide that the Zr concentration in the metal can be increased by increasing the excess Al and raising the ZrO{sub 2} mix. It was revealed from the above result that the ATR of mixed oxide of Nb{sub 2}O{sub 5}/ZrO{sub 2} can manufacture Nb-Zr containing Zr at more than 1%. 13 refs., 7 figs., 6 tabs.

  15. Experimental model for architectural systematization and its basic thermal performance. Part 1. Research on architectural systematization of energy conversion devices; Kenchiku system ka model no gaiyo to kihon seino ni tsuite. 1. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sunaga, N.; Ito, N.; Kimura, G.; Fukao, S.; Shimizu, T.; Tsunoda, M.; Muro, K. [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    The outline of a model for architectural systematization of natural energy conversion and the experiment result on the basic thermal performance in winter are described. The model is about 20 m{sup 2} in floor space. Foam polystyrene of 100 mm and 200 mm thick was used for the outer wall as heat insulating materials. The model has a solar battery and air conditioner and uses red brick as a heat reservoir. An experiment was made on seven modes obtained when three elements (heating, heat storage, and night insulated door) are combined. The information obtained by the experiment showed that a model for architectural systematization has high heat insulation and tightness and can be used as an energy element or an evaluation model for architectural systematization. In this model for architectural systematization, the power consumption of an air conditioner in winter can be fully supplied by only the power generation based on a solar battery. In an architectural element, the heating energy consumption can be remarkably reduced and the indoor thermal environment can be greatly improved, by the combination of a heat reservoir and night heat insulated door. 1 ref., 6 figs., 3 tabs.

  16. Annual cycle solar energy utilization with seasonal storage. Part 7. Examination on design and control of the system partially recovering exhaust heat of heat pump; Kisetsukan chikunetsu ni yoru nenkan cycle taiyo energy riyo system ni kansuru kenkyu. 7. Bubuntekina hainetsu kaishu wo koryoshita baai no sekkei seigyoho no kento

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1996-10-27

    The capacity and performance of the existing system that recovers the overall heating and cooling exhaust heat completely into a seasonal storage tank and the system that discharges the exhaust heat slightly to the outside and recovers it partially were compared and investigated. The system uses a central single-duct discharge system as an air-conditioning system. A heat pump and a flat-plate solar collector installed on the roof of a building are used as the heat source. The seasonal storage tank in the ground just under the building is a cylindrical water tank of 5 m deep with the concrete used as body. The upper surface of a storage tank is heat-insulated by a stylo-platform of 200 mm, and the lower side surface by a stylo-platform of 100 mm. Calculation when the difference in temperature used in a seasonal storage tank is set to 35{degree}C and 25{degree}C was performed for the system that has two control methods. The overall exhaust heat recovery system is almost the same in energy performance as the partial exhaust heat recovery system. The partial exhaust heat recovery system is more advantageous on the economic side. 4 refs., 6 figs., 3 tabs.

  17. Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Survey on the environmentally friendly type coal utilization system in the coal preparation sector in China; Kankyo chowagata sekitan riyo system kanosei chosa. Chugoku no sentan bumon ni okeru kankyo chowagata sekitan riyo system ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Specifying the coal preparation technology among clean coal technologies (CCT) in China, the paper investigated governmental policies, plans, standards of coal preparation technology, subjects, etc. toward the introduction/spread of coal preparation technology, and studied decision, introduction and spread of the coal preparation system suitable for the coal utilization status in China. The survey was conducted in Shanxi and Henan Provinces which are main provinces of coal production, and field survey was made at some selected coal preparation plants having different operational conditions. In the field survey, problems on the operation were extracted, and points of improvement were studied at the same time. Further, to grasp the positioning of coal preparation in CCT in China, survey was carried out on laws and regulation on coal preparation in terms of energy and environmental policies. Finally, the result of the field survey was analyzed, a coal preparation system of which the introduction/spread in medium- and long-term are enabled was proposed considering the coal utilization status and economic situation in China, and how to introduce/spread it was studied. 35 figs., 42 tabs.

  18. Numerical model for gas-liquid-solid three-phase mixture flow in a lifting pipe. 2nd Report. Fundamental study on lifting system for mixing marine mineral resources; Yoko kannai wo joshosuru kokieki sanso ryutai no ryudo ni kansuru suchi model. 2. Air lift hoshiki ni yoru shinkaitei shigen no yoko system no kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hatta, N.; Ishii, R. [Kyoto University, Kyoto (Japan). Faculty of Engineering

    1995-08-25

    This paper is concerned with constructing the numerical model for steady gas-liquid-solid three-phase mixture flow in a lifting pipe. Air lift pumps are regarded as one of the convenient means of lifting flurries and solid particles such as manganese nodules from the deep-sea bed of about 5,000 m to the sea surface. Here, the case is treated where the three-phase fluid is the slurry consisting of very small air bubble phase and solid particle phase mixed in water phase. The equations governing the gas-liquid-solid three-phase slurry flow are formed by three continuity equations, only one momentum equation, a gas equation of state and an equation for three-phase volume fractions. These six equations are cooperated into the only one equation to find the change in the gas-phase volume fraction according to the vertical position. Thereby, the remaining flow parameters can quantitatively be determined in the present model. Again, some numerical experiments are performed using this model. When the gas-phase volume fraction is given at the deep-sea bed, the corresponding solid-phase volume fraction can be determined between the upper and lower limits. It is shown that the solid-phase volume fraction near tee lower limits leads to increasing the lifting efficiency of the solid-phase. Furthermore, it is demonstrated that there is a limiting curve to predict the maximum solid-phase mass flux against the solid-phase volume fraction at tee deep sea bed. 16 refs., 4 figs., 1 tab.

  19. Survey report for fiscal 1998. Survey of the current state and tasks of research and development of technologies for effectively utilizing CO{sub 2} fixation by higher vegetation; 1998 nendo chosa hokokusho. Koto shokubutsu ni okeru nisanka tanso koteika yuko riyo gijutsu no kenkyu kaihatsu no genjo to kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations and studies are conducted seeking for a CO2 fixation method improved by utilizing the photosynthesizing function of higher vegetation. Details of higher vegetation genes are being disclosed thanks to the rapid progress of studies making use of molecular biological techniques, and the application of the genetic mechanism to scientific and technological fields is becoming increasingly feasible. In particular, the role of the CO2 fixation enzyme RuBisCO has been elucidated almost completely. It has been learned that, in terms of photosynthesizing capability, the C{sub 4} plants (corn etc.) are 2-3 times higher than the C{sub 3} plants (rice, wheat, etc.), and 5-10 times higher than the CAM plants (cactuses etc.). Studies are also under way about the rice genome so that a photosynthesizing capability so high as that of the C{sub 4} plants may be endowed the rice plant. The metabolism and control of useful substances produced in the CO2 fixation process etc. in the higher vegetation are being investigated, and it is now expected that some day such useful substances will be produced and utilized efficiently. Researches are under way into the relationship between the green leaf that is the organ that performs photosynthesis and the organ (sink) that stores and utilizes starch and sugar is in progress, and now a new field is going to open where vegetables will be fully utilized. (NEDO)

  20. FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

  1. Achievement report for fiscal 1998 on the preceding research related to global environment industry technologies. Survey and research on reduction of nitrogen monoxide; 1998 nendo chikyu sangyo gijutsu ni kakawaru sendo kenkyu asanka chisso no haishutsu teigen ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Nitrogen monoxide is a strong greenhouse effect gas having warming up index per molecule 300 times greater than that of CO2, and is designated as the object of reduction in the Kyoto Conference. The present preceding research discusses necessity of performing research and development works related to reducing the emission of nitrogen monoxide, and if it is necessary, places the final objective on proposition of what researches should be planned. Fiscal 1997 being the first fiscal year of the preceding research has surveyed emission amount from different emission sources, and enumerated the research and development assignments. Fiscal 1998 falling under the final fiscal year summarizes the emission amount including the future trends, surveys the feasibility of the promising technological measures through experiments, and proposed finally a research and development plan desired of implementation in the future. The proposal contains a research plan placing development of nitrogen monoxide decomposing catalysts and automobile catalysts as the main objectives. Among the domestic nitrogen monoxide generating sources, about 2/3 is the man-made generation sources, hence catalysts, if developed, may be applied to such facilities as combustion furnaces. (NEDO)

  2. FY 2000 research cooperation project on the comprehensive research cooperation for environmental technology. Research cooperation for technology for prevention of the water pollution caused by plant waste water in Vietnam; 2000 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku (Betonamu koku kojo haisui ni yoru suishitsu osen boshi taisaku gijutsu ni kansuru kenkyu hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of increasing the research capability of the Center for Consultancy, Training and Technology Transfer in Vietnam, research cooperation for prevention of water pollution was given for plants of the local industry located in the suburbs of Hanoi city. In the survey of the actual state of the water pollution in the industrial area in the suburbs of Hanoi city, the following was found out: In the area, approximately 110 companies of the production industry such as livestock feed, papermaking, dyeing, brewing, construction materials, etc. are in operation and are discharging the untreated waste water into rivers and waterways because waste water treatment facilities are not prepared yet. In this research cooperation, the following were carried out: detailed survey of specified plants and proposal for improvement, training of Vietnamese researchers/engineers in charge of water pollution prevention technology, invitation to/training at Japan of Vietnamese managers/researchers, seminar to be held on the site, equipment to be given that is needed to measure water quality. The equipment to be given is a portable multi-item water quality meter and analytical equipment such as spectrometer, atomic absorption spectrophotometer and gas chromatograph. (NEDO)

  3. Research on acoustic characteristics of materials. Development of sound absorbing materials of an automobile engine undercover using a small sized reverberation chamber; Zairyo no onkyo tokusei ni kansuru kenkyu. Kan`i zankyoshitsu ni yoru jidoshayo undercover no kyuonzai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, K.; Yugami, T.; Wakabayashi, F.; Kitagawa, T.; Hasegawa, K. [Shizuoka Industrial Research Institute of Shizuoka Prefecture, Shizuoka (Japan); Terajima, Y.; Ajioka, D.; Kondo, H.; Watanabe, H.; Fujii, H.

    1996-09-01

    Japan Automobile Research Institute (JARI) has test equipment with a 36m{sup 3} reverberance chamber and uses a 3.3m{sup 2} test piece. In the titled test, however, a simpler 9.9m{sup 3} system and a smaller 0.82m{sup 2} piece were used. To evaluate the difference in characteristics between the two systems, comparison was made in point of reverberation box dark noise level, reverberation time, diffusion of the sound field, and absorption rate, and any difference in measured value between the two was examined and remedial actions were taken. As the result, it was learned that, in point of the random incidence absorption rate, the value collected from this smaller system agreed well with that of the larger reverberation chamber system. The same was true of the transmission loss measurement. This smaller system performed better than a reverberation chamber of JISA1409 in absorption rate measurement or a JISA1416 laboratory in sound transmission measurement. This system, excellent in the ease of specimen preparation, experimenting cost, and time required for measuring, will be a useful tool for the development of acoustical materials. 1 ref, 17 figs.

  4. Electron attachment coefficient in low E/N regions and a discussion of discharge-instability in KrF laser. ; Analysis by logarithm transformed Boltzmann equation. Tei E/N ryoiki no denshi fuchaku keisu to KrF laser reiki hoden no fuanteisei ni kansuru ichi kosatsu. ; Tai su henkan Boltzmann hoteishiki ni yoru kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, H.; Urabe, J.; Yukimura, K. (Doshisha Univ., Kyoto (Japan))

    1991-03-20

    In a discharge excitation rare gas halide excima laser, uniform generation and stable maintenance of the excited discharge determines the laser characteristics. In this report, an approximate solution was obtained on the Boltzmann equation (frequently used for the theoretical analysis of this laser) to examine the nature of the solution. By optimizing the conversion of the variables, calculation of an electron swarm parameter in the hitherto uncertain range of the low conversion electric field was made possible, giving a generation mechanism of the uncertainty of the excited dischareg. The results are summarized as below. (1) The Boltzmann equation gives a linear solution for a logarithmic value of an electron energy in the range of low conversion electric field. (2) Time-wise responce ability between the measured voltage, current characteristics of the excitation discharge was clarified and the attachment and ionization coefficients calculated by Boltzmann equation. (3) Dependency of the attachment coefficient on the partial pressure of fluorine and kripton was examined, and the attachment coefficient was found to increase with the increase of the partial pressure for the both cases. 20 refs., 9 figs., 2 tabs.

  5. Theoretical study on instability mechanism of jet-induced sloshing. Model development using Orr-Sommerfeld equation generalized for non-parallel flow; Funryu reiki sloshing gensho no hassei kiko ni kansuru rironteki kenkyu. Hiheiko nagare ni ippankashita Orr-Sommerfeld hoteishiki wo mochiita model ka

    Energy Technology Data Exchange (ETDEWEB)

    Eguchi, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1998-07-25

    A theoretical model was developed to study the mechanism of free surface sloshing in a vessel induced by a steady vertical jet flow. In the model, jet deflection is calculated with eigen values of the generalized Orr-Sommerfeld equation which is applicable to slightly non-parallel jet. Instability criteria employed in the model are (1) resonace condition between sloshing and jet frequencies and (2) {pi} phase relation between jet displacement at an inlet and global jet deflection. Numerical results of the mathematical model have shown good agreement with experimental ones, which justifies that the inherent instability of free jet itself and edge tone feedback are the main causes of the self-excited sloshing. 9 refs., 10 figs.

  6. Combustion characteristics of stratified mixture. 1st Report. Measurement of mixture distribution in a constant-volume combustion chamber using laser-induced NO2 fluorescence; Sojo kongoki no nensho tokusei ni kansuru kenkyu. 1. Laser reiki NO2 keikoho ni yoru teiyo nenshokinai kongoki bunpu no keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, M.; Nishida, K.; Hiroyasu, H. [Hiroshima University, Hiroshima (Japan). Faculty of Engineering; Tabata, M. [Mazda Motor Corp., Hiroshima (Japan)

    1996-06-25

    Laser-induced fluorescence from nitrogen dioxide (NO2) as gas fuel tracer was applied to determine mixture stratification in a pancake-type constant-volume combustion chamber using propane and hydrogen fuels. The second-harmonic output of a pulsed Nd: YAG laser was used as a light source for fluorescence excitation. The fluorescence images were corrected by a gated image-intensified CCD camera. The quantitative analysis of fuel concentration was made possible by the application of linearity between fluorescence intensity and NO2 concentration at a low trace level. The stratified mixture (center-rich or center-lean) was concentrically formed in the central region of the chamber by a jet flow from a tangentially oriented port. The concentration difference in the radial direction of the chamber decreased with time from the start of injection. The rate of decrease was faster for hydrogen than for propane. After 300 ms from start of injection, however, the time histories of the concentration difference were nearly constant for both fuels regardless of overall concentration. 10 refs., 16 figs., 1 tab.

  7. FY 1997 report on the study on cryogenic aggregate target PLD process by multi-laser excitation for using gaseous materials; 1997 nendo chosa hokokusho (kitai genryo riyo no tame no taju laser reiki ni yoru gokuteion gyoshutai target PLD process ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the result in fiscal 1995 of the study on PLD (pulse laser deposition) thin film formation process having been made since 1993. In fiscal 1995, the effect of irradiation of excimer laser and YGA(SHG) on ablation of aggregates of N2, CH4, Ar, Kr and Xe, and the effect of time-delayed irradiation of YGA(SHG) and KrF excimer laser on ablation of N2 aggregate were studied aiming at exciting ablation by cryogenic aggregate alone. Experimental results by a newly developed multi-laser excitation experiment equipment are as follows. Ablation was not caused by KrF excimer laser irradiation, while caused by YGA(SHG) irradiation. Ablation was caused by 1mm thick N2 or CH4 aggregate alone. Kr target was the most promising among rare gas solid targets expected as seed of ablation occurrence. Multi-irradiation showed a different ablation behavior as compared with single YGA(SHG) irradiation, and in some cases, multi-irradiation not increased scattering of particles. Time-delayed multi- irradiation (YGA(SHG) excitation after excimer excitation) was effective. 23 figs., 4 tabs.

  8. Studies on the utilization of by-products in food manufactures by methods of biotechnology (8). Development of lactic acid beverage using white rice flour; Baio tekunoroji ni yoru shokuhin fukusanbutsu no kodo riyo ni kansuru kenkyu (8). Hakko wo genryo toshita nyusankin inryo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sugano, N.; Uehigashi, H.; Moriyama, H.; Hisatake, M. [Kochi Prefectural Industrial Technology Center, Kochi (Japan)

    1999-11-25

    The lactic acid bacteria beverage under alcohol 1% is reported, because lactic acid and yeast were added to saccharification liquid that made and enzymegenationed white rice flour which is a by-product of sake brewing to be raw material, and because the fermentation was done and was produced. The lactic bacteria selected 2 stocks on 7 kinds of strain from breeding and living acidity and sensory of fermented liquor in the white rice flour saccharification liquid. In the drink, a balance of sourness and sweetness is important. The optimum onset sugar concentration is estimated from the sensory test for the drink of which sugar content differs from the acidity. In Lactobacillus lactis subsplactis IAM1198 of which sugar content of 22.5 and living acidity were low in Lactobacillus acidophilus IAM10074 of which the living acidity is high, the fermentation was done in sugar content of 20.0, and it produced the drink with the good flavor. (NEDO)

  9. Recent energy situation in the U.S. and Europe. Trend of discussions on energy safety security and energy policies in the E.U. and CIS (commonwealth of independent states) countries; Obei ni okeru saikin no energy jijo. Energy anzen hosho ni kansuru giron no doko to EU oyobi CIS shokoku no energy seisaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The E.U. intends to establish the stabilized new partnership and economic area, based on free trades and tighter economic cooperation with Mediterranean countries. For the purpose of establishing the effective cooperative relationship in the energy field, the E.U. committee taking the short- and medium-term initiative prepares as follows: The establishment of the European/Mediterranean Energy Forum is thought of. This is for the joint management of cooperation in the energy field and the organization of the conferences and meetings of information exchanges between partners. The discussion is started for the final joining in the organization of partners of Mediterranean countries who do not participate in the Pan-European Energy Charter conference. They study options adoptable for easing investments. They cooperate with the related countries for carrying out the project having common interest in the TENs (Trans-European energy networks) field. The working-out of plans and projects is promoted for coordinating energy projects according to the purposes and procedures of MEDA. 59 refs.

  10. Fiscal 1998 research report. Survey on development and application of membranes with pores of micron to nano-meter sizes; 1998 nendo chosa kenkyu hokokusho. Makuro kara mikuro (nano mezo dai) size wo motsu, menburenmaku no kaihatsu narabi ni oyo ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Researches on preparation of membranes of various materials have been promoted by not systematic technique but separate techniques according to needs of concerned fields. To establish the efficient technique for membranes with pores of required uniform size according to needs of various industries, survey and study were made on process optimization and low-cost production method. Porous membrane is the leading candidate for new separation systems as separation medium in chemical industry, hot gas filtration for energy production and environmental purification engineering. The electrode, separator and gas storage medium of fuel cell vehicles and next-generation batteries require effective porous materials. The workshop on engineering porous materials held in May 1993 confirmed the time of following materials: High-efficiency gas separation membrane, chemical catalytic membrane, fuel cell electrode and absorbent for environmental purification. Development of inorganic membranes more excellent in high-temperature stability, strength, catalytic activity and corrosion resistance than previous polymer membranes is important. (NEDO)

  11. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research on energy (Research and development of biofuel production using highly functional bioreactor - 2nd year); 1999 nendo kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu seika hokokusho (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Microbes capable of a high biodiesel fuel (BDF) yield from moisture-containing oils assumedly waste oil are investigated. Lipase attributed to Rhizopus oryzae exhibits a high reaction rate of not lower than 90%. The process functions even when microbes are immobilized by BSPs. BDF does not affect driving performance, and black smoke is reduced. A process basic to industrial production is developed by use of a fixed bed reactor. In the production of ethanol from starch thanks to plural kinds of glucoamylase producing yeast, ethanol is produced at a rate of 7-8% under microaerophilic conditions in both proliferation and fermentation periods, which means a success achieved in growing arming yeast equipped with enhanced functions. A 20-liter class bench plant is installed and immobilization by BSPs is tested, when no problem is detected. In a reaction involving these immobilized microbes, a reaction rate near 16% is achieved. In the production of ethanol by yeast immobilized by BSPs, use of a fuzzy control system is studied, and it is found that prolonged stability is available when glucose concentration is sustained at 10-20g/liter. (NEDO)

  12. Study on solidification of carbon dioxide by using cold energy of LNG. 2nd Report. Solidification characteristics of CO2 around gas feed nozzle; LNG no reinetsu wo riyoshita tansan gas no koka ni kansuru kiso kenkyu. 2. Gas fukikomi nozzle shuhen ni okeru CO2 koka tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, Y.; Hironaka, S. [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Shimada, Y.; Tokumasa, K. [Chugoku Electric Power Co. Inc., Hiroshima (Japan)

    1998-08-25

    The present paper deals with solidification characteristics of carbon dioxide around gas feed nozzle of the flue gas from thermal energy power plant. The present experiment was carried out under condition of dioxide content for 3-50 volume percents. The results obtained indicated that the solidification fraction of carbon dioxide increased with a decrease in cooling temperature. The solidification fraction of carbon dioxide was expressed as the function of non-dimensional tempera true and concentration of carbon dioxide. 6 refs., 15 figs.

  13. Achievement report for fiscal 1998 on area consortium research and development business, 1st year. Area consortium energy research and development (biofuel production by advanced function bioreactor); 1998 nendo chiiki consortium energy bun'ya. Kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Studies were made to produce ethanol directly from starch and cellulose and to collect biodiesel fuels from waste oil by an enzymatic method. For an increase in the yield of biodiesel fuel production, lipase enzymes were explored and optimum reaction conditions were sought for. Starch decomposition was quick for conversion into the target material in a system with the co-expression of amylase and glucoamylase present on the yeast cell surface layer. There was dramatically rapid progress in the increase of enzymatic activity in the cell, although dependent on cell membrane surface treatment conditions. In the generation of acetaminophen by recombinant cohesive yeasts, highly active and expressive yeasts were automatically fixed in the porous support (intelligent bioreactor) while those deactivated or dead were automatically removed. For the construction of a fuzzy control system for this reaction, basic models were investigated, built on the basis of the enzymatic model of reaction and substance balance. A high-precision structural analysis was conducted for the exploration of secondary structure stabilizing factors in protein and peptide and for the elucidation of correlations between structure and function. (NEDO)

  14. Fiscal 1997 report on the results of the international standardization R and D. Study on optimizing design/evaluation technology using quality engineering; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Hinshitsu kogaku ni yoru saitekika sekkei hyoka gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To take up methodology of quality engineering as ISO standards, the basic document was worked out which regulates general items for the method to evaluate the operation of various systems as function for proposal to ISO. A method is developed for evaluating the design quality by function and predicting/optimizing the quality of finished products. For the evaluation of slippage from ideal function, the SN ratio and Maharanobis`s distance are used. In the two basic working groups (WG), a document on general methods to evaluate function was made. To reinforce the basic document, WGs divided into five by content/business were set up. Each WG collected examples from the past, studied methods to evaluate function in each field, and recorded them in the document. Five experiments for each WG were conducted to verify effectiveness of the above-mentioned method to evaluate function recorded in the document. As a result, the draft to present to ISO was worked out since the experimental WGs proved the effectiveness of the method to evaluate function in each field. 85 refs., 147 figs., 185 tabs.

  15. Achievement report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansru kenkyu kyoryoku' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The subject project is implemented in the fields of automobiles and their parts, electrical home appliances and their parts, and textile and apparel. In the field of automobiles and their parts, a prototype is developed of an integrated information management system which is to serve between corporation head offices and assembling businesses overseas, and another prototype is developed of an inter-business technical data serving system which is to serve between overseas assembling businesses and supporting businesses, both involving Japan, Indonesia, and Thailand. In the field of electrical home appliances and their parts, a prototype is developed of an electronic catalog system in a joint endeavor with research institutes of Indonesia, Malaysia, Singapore, and Thailand, and a demonstration test is conducted. A design concurrent engineering system is developed by Japan and Malaysian research institutes. In the field of textile and apparel, prototypes are developed, by Japanese, Chinese, and Indonesian apparel manufactures, of an apparel manufacturing specification system, international EDI (electronic data interchange) system, translation system, and a CAD (computer-aided design)/CAM (computer-aided manufacturing) data interchange system. (NEDO)

  16. Microstructure and mechanical properties of sputter deposited Ni/Ni{sub 3}Al multilayer films at elevated temperature

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Chao [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Feng, Kai, E-mail: fengkai@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Li, Zhuguo, E-mail: lizg@sjtu.edu.cn [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China); Lu, Fenggui; Huang, Jian; Wu, Yixiong [Shanghai Key Laboratory of Materials Laser Processing and Modification, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Collaborative Innovation Center for Advanced Ship and Deep-Sea Exploration, Shanghai 200240 (China)

    2016-08-15

    Highlights: • Ni/Ni{sub 3}Al multilayers are prepared by magnetron sputtering. • Both grain size and phase constitution of annealed Ni/Ni{sub 3}Al multilayers are dependent on individual layer thickness. • The hardness of annealed Ni/Ni{sub 3}Al multilayers varies with individual layer thickness and annealing temperature. • 40 nm Ni/Ni{sub 3}Al multilayer exhibits excellent hardness at elevated temperature. - Abstract: Nano-structured Ni/Ni{sub 3}Al multilayer was prepared by magnetron sputtering, with individual layer thicknesses h varying from 10 to 160 nm. The microstructure and hardness of Ni/Ni{sub 3}Al multilayer were investigated by X-ray diffraction, transmission electron microscopy and nanoindentation. The results show that the hardness increases with decreasing h for as-deposited and 500 °C annealed multilayers. When annealed at 700 °C, the hardness approach a peak value at h = 40 nm with followed by softening at smaller h. The influence of individual layer thickness, grain size as well as formation of ordered Ni{sub 3}Al on strengthening mechanisms of Ni/Ni{sub 3}Al multilayers at elevated temperature are discussed.

  17. Direct versus hydrogen-assisted CO dissociation over stepped Ni and Ni3Fe surfaces: a computational investigation.

    Science.gov (United States)

    Yang, Kuiwei; Zhang, Minhua; Yu, Yingzhe

    2015-11-28

    The adsorption and dissociation of CO over stepped Ni and Ni3Fe surfaces were systematically studied using density functional theory slab calculations. Both (211)-like surface structure terminations (NiNi step and NiFe step, denoted as Ni3Fe(211)-AA and Ni3Fe(211)-AB) are considered for Ni3Fe. Direct scission of the C-O bond in CO is identified as the least likely one among the three proposed dissociation pathways and CO dissociation via a CHO intermediate appears to be most feasible at low CO coverage on pure and alloyed Ni(211) surfaces. The priority of H-assisted CO dissociation might originate from the more activated C-O bond in COH and CHO. Compared to Ni(211), the Ni3Fe(211)-AB surface could facilitate CO activation especially for the most possible CHO intermediate mechanism, whose rate-limiting step is found to be altered. The d-band center theory and Mulliken charge analysis are also employed to explain the activity difference between Ni3Fe(211)-AB and Ni3Fe(211)-AA. The significant structural sensitivity of CO dissociation highlights the importance of Fe locating in the step edge and the high reactivity of Ni3Fe(211)-AB is largely ascribed to the synergistic effect between Ni and Fe at the step edge.

  18. Single-crystalline Ni2Ge/Ge/Ni2Ge nanowire heterostructure transistors.

    Science.gov (United States)

    Tang, Jianshi; Wang, Chiu-Yen; Xiu, Faxian; Hong, Augustin J; Chen, Shengyu; Wang, Minsheng; Zeng, Caifu; Yang, Hong-Jie; Tuan, Hsing-Yu; Tsai, Cho-Jen; Chen, Lih Juann; Wang, Kang L

    2010-12-17

    In this study, we report on the formation of a single-crystalline Ni(2)Ge/Ge/Ni(2)Ge nanowire heterostructure and its field effect characteristics by controlled reaction between a supercritical fluid-liquid-solid (SFLS) synthesized Ge nanowire and Ni metal contacts. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies reveal a wide temperature range to convert the Ge nanowire to single-crystalline Ni(2)Ge by a thermal diffusion process. The maximum current density of the fully germanide Ni(2)Ge nanowires exceeds 3.5 × 10(7) A cm(-2), and the resistivity is about 88 μΩ cm. The in situ reaction examined by TEM shows atomically sharp interfaces for the Ni(2)Ge/Ge/Ni(2)Ge heterostructure. The interface epitaxial relationships are determined to be [Formula: see text] and [Formula: see text]. Back-gate field effect transistors (FETs) were also fabricated using this low resistivity Ni(2)Ge as source/drain contacts. Electrical measurements show a good p-type FET behavior with an on/off ratio over 10(3) and a one order of magnitude improvement in hole mobility from that of SFLS-synthesized Ge nanowire.

  19. Eutectic superalloys strengthened by delta Ni3Cb lamellae, and gamma prime, Ni3Al precipitates.

    Science.gov (United States)

    Lemkey, F. D.; Thompson, E. R.

    1972-01-01

    Bivariant eutectic alloys, located on a liquidus surface within the Ni-Cb-Cr-Al quaternary, were identified which permitted the production of aligned delta Ni3Cb lamellae within a nichrome matrix containing the fcc precipitate gamma prime Ni3Al. The volume fraction of delta and gamma prime could be varied significantly by compositional changes. After directional solidification certain alloys possessed improved ductility and corrosion resistance with respect to the Ni3Al-Ni3Cb eutectic, while their values of tensile and creep strength approached or exceeded those for the Ni3Al-Ni3Cb pseudobinary system. The mechanical properties of the directionally solidified alloy, Ni-19.7 wt % Cb-6.0 wt % Cr-2.5 wt % Al, were evaluated. Its longitudinal strength in tension and creep was found to be superior to all advanced nickel base superalloys. It is thus demonstrated that useful properties for gas turbine airfoil applications can be achieved by reinforcing a strong and tough gamma nichrome matrix containing precipitated gamma prime by a strong lamellar intermetallic compound having greater strength at elevated temperature.

  20. Ni(salen): a system that forms many solvates with interacting Ni atoms

    NARCIS (Netherlands)

    Siegler, M.A.M.|info:eu-repo/dai/nl/31411744X; Lutz, M.|info:eu-repo/dai/nl/304828971

    2009-01-01

    Recrystallization of [N,N’-Ethylene-bis(salicylideneiminato)]-nickel(II) [Ni(salen)] has been carried out from a large selection of solvents. Crystals can be either solvent free or solvates. This study is based on X-ray crystal structure determinations, which include the redetermination of Ni(salen)

  1. Enhanced Electrocatalytic Activity for Water Splitting on NiO/Ni/Carbon Fiber Paper

    Directory of Open Access Journals (Sweden)

    Ruoyu Zhang

    2016-12-01

    Full Text Available Large-scale growth of low-cost, efficient, and durable non-noble metal-based electrocatalysts for water splitting is crucial for future renewable energy systems. Atomic layer deposition (ALD provides a promising route for depositing uniform thin coatings of electrocatalysts, which are useful in many technologies, including the splitting of water. In this communication, we report the growth of a NiO/Ni catalyst directly on carbon fiber paper by atomic layer deposition and report subsequent reduction and oxidation annealing treatments. The 10–20 nm NiO/Ni nanoparticle catalysts can reach a current density of 10 mA·cm−2 at an overpotential of 189 mV for hydrogen evolution reactions and 257 mV for oxygen evolution reactions with high stability. We further successfully achieved a water splitting current density of 10 mA·cm−2 at 1.78 V using a typical NiO/Ni coated carbon fiber paper two-electrode setup. The results suggest that nanoparticulate NiO/Ni is an active, stable, and noble-metal-free electrocatalyst, which facilitates a method for future water splitting applications.

  2. Adherencia al tratamiento en niñas y niños con VIH

    Directory of Open Access Journals (Sweden)

    Ana María Ruiz Navia

    2009-01-01

    Full Text Available Este artículo describe y determina el grado de adherencia al tratamiento en niños y niñas con VIH/ SIDA teniendo en cuenta los comportamientos y las variables asociadas a ésta. La muestra estuvo conformada por 1 niño y 5 niñas, diagnosticados con VIH, y su respectivo cuidador primario, quienes respondieron a la entrevista semiestructurada de evaluación de adherencia para niños y niñas con VIH/ SIDA ad hoc y a la entrevista semiestructurada de evaluación de adherencia para niños y niñas con VIH/SIDA versión cuidador primario ad hoc, respectivamente. Los resultados muestran la presencia de conductas de adherencia en los participantes del estudio, evidenciando la influencia de una serie de variables determinantes para este comportamiento. Cinco de los participantes cumplieron más del 95% de adherencia, mientras que uno se ubicó por debajo de este porcentaje. Como aspectos centrales se destacan la influencia de los estados emocionales en la toma del medicamento y la importancia del rol del cuidador primario en la adherencia.

  3. Magnetic properties of monodispersed Ni/NiO core-shell nanoparticles.

    Science.gov (United States)

    Seto, Takafumi; Akinaga, Hiroyuki; Takano, Fumiyoshi; Koga, Kenji; Orii, Takaaki; Hirasawa, Makoto

    2005-07-21

    We have recently developed a method to fabricate monodispersed Ni/NiO core-shell nanoparticles by pulsed laser ablation. In this report, the size-dependent magnetic properties of monodispersed Ni/NiO core-shell nanoparticles were investigated. These nanoparticles were formed in two steps. The first was to fabricate a series of monodispersed Ni nanoparticles of 5 to 20 nm in diameter using a combination of laser ablation and size classification by a low-pressure differential mobility analyzer (DMA). The second step was to oxidize the surfaces of the Ni particles in situ to form core-shell structures. A superconducting quantum interference device (SQUID) magnetometer was used to measure the magnetic properties of nanostructured films prepared by depositing the nanoparticles at room temperature. Ferromagnetism was observed in the magnetic hysteresis loop of the nanostructured films composed of core-shell nanoparticles with core diameters smaller than the superparamagnetic limit, which suggests the spin of Ni core was weakly exchange coupled with antiferromagnetic NiO shell. In contrast, smaller nanoparticles with core diameters of 3.0 nm exhibited superparamagnetism. The drastic change in the hysteresis loops between field-deposited and zero-field-deposited samples was attributable to the strong anisotropy that developed during the magnetic-field-assisted nanostructuring process.

  4. Ab initio phonon calculations for Ll(2) Ni3Al and B2NiAl

    NARCIS (Netherlands)

    Isaeva, E.I.; Lichtenstein, A.I.; Vekilov, Y.K.; Smirnova, E.A.; Abrikosov, I.A.; Simak, S.I.; Ahuja, R.; Johansson, B.

    2004-01-01

    The phonon spectra and phonon density of states of the Ni3Al and NiAl intermetallic compounds are calculated from first principles using the linear response method in conjunction with ultrasoft pseudopotentials. The calculated phonon dispersion curves are in good agreement with available

  5. Reactivity and wettability of SiC by Ni and Ni-Si alloys

    Energy Technology Data Exchange (ETDEWEB)

    Rado, C. [INPG, 38 - Saint Martin d`Heres (France). LTPCM; Kalogeropoulou, S. [INPG, 38 - Saint Martin d`Heres (France). LTPCM; Eustathopoulos, N. [INPG, 38 - Saint Martin d`Heres (France). LTPCM

    1996-08-01

    Wettability of SiC by Ni and Ni-Si alloys was studied at 1633K by the sessile drop technique under high vacuum or pure He. It is shown that reactivity in this system can be controlled and even nearly suppressed while obtaining good wetting and strong interface. (orig.)

  6. Probing the semi-magicity of $^{68}$Ni via the $^{3}$H($^{66}$Ni,$^{68}$Ni)p two-neutron transfer reaction in inverse kinematics

    CERN Multimedia

    Reiter, P; Blazhev, A A; Kruecken, R; Franchoo, S; Mertzimekis, T; Darby, I G; Van de walle, J; Raabe, R; Elseviers, J; Gernhaeuser, R A; Sorlin, O H; Georgiev, G P; Bree, N C F; Habs, D; Chapman, R; Gaudefroy, L; Diriken, J V J; Jenkins, D G; Kroell, T; Axiotis, M; Huyse, M L; Patronis, N

    We propose to perform the two-neutron transfer reaction $^{3}$H($^{66}$Ni, $^{68}$Ni)$p$ using the ISOLDE radioactive ion beam at 2.7 $A$ MeV and the MINIBALL + T-REX setup to characterize the 0$^{+}$ and 2$^{+}$ states in $^{68}$Ni.

  7. Ni(OH){sub 2} and NiO nano structures: Synthesis, characterization and electrochemical performance

    Energy Technology Data Exchange (ETDEWEB)

    Saghatforoush, Lotf Ali; Sanati, Soheila; Mehdizadeh, Robabeh [Payam Noor Univ., Tehran (Iran, Islamic Republic of); Hasanzadeh, Mohammad [Tabriz Univ. of Medical Sciences, Tabriz (Iran, Islamic Republic of)

    2012-04-15

    Hydrothermal route have been used in different conditions for preparation of Ni(OH){sub 2} nano structures. The NiO nanoparticles were obtained by calcining the Ni(OH){sub 2} precursor at 450 .deg. C for 2 h. The effect of sodium dodecyl sulfonate (SDS) as surfactant on the morphology and size of Ni(OH){sub 2} nanoparticles were discussed in detail. X-ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) spectroscopy were used to characterize the products. The growth mechanism of the as-synthesized nano structures was also discussed in detail based on the experimental results. Coming up, the NiO nanoparticle modified carbon paste electrode was applied to the determination of captopril in aqueous solution.

  8. NiO Nanoparticles: Synthesis and Characterization

    Directory of Open Access Journals (Sweden)

    A. Rahdar

    2015-04-01

    Full Text Available In the current paper,Nanostructured Nickel oxide (NiO were synthesized by co-precipitation method using Nickel(II Chloride Hexahydrate (NiCl2.6H2O and sodium hydroxide (NaOH as starting material. Structural, optical and magnetic properties of nanostructures were characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, Atomic force microscope (AFM, UV–Vis absorption; Fourier transformed infrared (FTIR and vibrating sample magnetometer (VSM technique. The X-ray diffraction pattern studies revealed the NiO have a  face-centered cubic (FCC structure and confirmed the presence of high degree of crystallinity nature NiO nanoparticles that their average size is found to be 26 nm. The composition of nanostructures confirmed by analysis of FTIR spectra. The average size of the NiO nanoparticle observed from scanning electron microscopy images is found to be dimensions about 24 nm. Magnetic measurement confirmed the Nickel Oxide nanostructures superparamagnetic behavior at room temperature (RT after calcinations.

  9. Hydrothermal synthesis of α-Ni(OH){sub 2} and its conversion to NiO with electrochemical properties

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Yong; Ma, Jianmin, E-mail: nanoelechem@hnu.edu.cn; Wang, Taihong, E-mail: thwang@hnu.edu.cn

    2014-01-05

    Highlights: • α-Ni(OH){sub 2} microspheres have been synthesized with triethanolamine. • The formation mechanism of α-Ni(OH){sub 2} microspheres is suggested. • NiO deriving from α-Ni(OH){sub 2} microspheres exhibits better electrochemical performances. -- Abstract: The paper reports the fabrication of microscale NiO matrixes with enhanced electrochemical properties through annealing the corresponding chrysanthemum-like α-Ni(OH){sub 2} microspheres. The precursor α-Ni(OH){sub 2} can be synthesized by a hydrothermal method using triethanolamine as the alkaline source. The formation mechanism of chrysanthemum-like α-Ni(OH){sub 2} microspheres is properly discussed. Furthermore, the electrochemical experiments demonstrate that the microscale NiO matrixes show superior electrochemical behavior in lithium-ion batteries due to their unique structures.

  10. Exchange bias effect in polycrystalline NiO/NiMn{sub 2}O{sub 4} composite

    Energy Technology Data Exchange (ETDEWEB)

    Freitas Cabral, A.J. [Instituto de Ciências Exatas e Naturais, Universidade Federal do Pará (UFPA), Belém, PA (Brazil); Peña Serna, J.; Rache Salles, B.; Novak, M.A. [Instituto de Física, Universidade Federal do Rio de janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Pinto, A.L. [Centro Brasileiro de Pesquisas Físicas (CBPF), Rio de Janeiro, RJ (Brazil); Rocha Remédios, C.M. [Instituto de Ciências Exatas e Naturais, Universidade Federal do Pará (UFPA), Belém, PA (Brazil)

    2015-05-05

    Highlights: • Antiferromagnetic NiO/ferrimagnetic NiMn{sub 2}O{sub 4} oxide composites. • Grains are well faceted, indicating that the specimen was well crystallized. • The micrographs suggests that NiO and NiMn{sub 2}O{sub 4} may be stuck to each other. • EB effect in NiO/NiMn{sub 2}O{sub 4} oxide composites. • EB effect increases with the amount of NiO. - Abstract: Calcination of aqueous solutions formed by different molar ratios between the nickel and manganese chlorides led to the formation of antiferromagnetic NiO/ferrimagnetic NiMn{sub 2}O{sub 4} oxide composites, as determined by X-ray powder diffraction technique and Rietveld refinement. Low temperature zero field cooled and field cooled magnetic hysteresis cycles show an exchange bias effect, presumably due to interaction at the interfaces between the antiferromagnetic and ferrimagnetic materials.

  11. Hydrogenation of Amorphous and Crystalline RE-Ni Alloys

    OpenAIRE

    AOKI, Kiyoshi; Shirakawa, Kiwamu; MASUMOTO, Tsuyoshi

    1985-01-01

    Amorphous alloys with the combination of a rare earth metal(RE=Y, La, Ce, Pr and Sm) and nickel were prepared around the composition at an eutectic point by the melt-quenching technique. Amorphous Y-Ni and Sm-Ni alloys absorbed a large amount of hydrogen even in the amorphous state, while the the other alloys in La-Ni, Ce-Ni and Pr-Ni systems were decomposed to a mixture of crystalline phase and hydride during hydrogenation at 323 K. An amorphous SmNi_2 phase was also synthesized by reaction ...

  12. Reduction of a Ni/Spinel Catalyst for Methane Reforming

    DEFF Research Database (Denmark)

    Kehres, Jan; Andreasen, Jens Wenzel; Fløystad, Jostein Bø

    2015-01-01

    A nickel/spinel (Ni/MgAl2O4) catalyst, w(Ni) = 22 wt%, was investigated in situ during reduction with wide angle X-ray scattering (WAXS) in a laboratory setup and with anomalous small angle X-ray scattering (ASAXS) at a synchrotron source. Complementary high resolution transmission electron...... microscopy (HRTEM) was performed on the fresh catalyst sample. The Ni particles in the fresh catalyst sample were observed to exhibit a Ni/NiO core/shell structure. A decrease of the Ni lattice parameter is observed during the reduction in a temperature interval from 413 – 453 K, which can be related...

  13. Evolution of Ni nanofilaments and electromagnetic coupling in the resistive switching of NiO

    Science.gov (United States)

    Luo, Yuxiang; Zhao, Diyang; Zhao, Yonggang; Chiang, Fu-Kuo; Chen, Pengcheng; Guo, Minghua; Luo, Nannan; Jiang, Xingli; Miao, Peixian; Sun, Ying; Chen, Aitian; Lin, Zhu; Li, Jianqi; Duan, Wenhui; Cai, Jianwang; Wang, Yayu

    2014-12-01

    Resistive switching effect in conductor/insulator/conductor thin-film stacks is promising for resistance random access memory with high-density, fast speed, low power dissipation and high endurance, as well as novel computer logic architectures. NiO is a model system for the resistive switching effect and the formation/rupture of Ni nanofilaments is considered to be essential. However, it is not clear how the nanofilaments evolve in the switching process. Moreover, since Ni nanofilaments should be ferromagnetic, it provides an opportunity to explore the electromagnetic coupling in this system. Here, we report a direct observation of Ni nanofilaments and their specific evolution process for the first time by a combination of various measurements and theoretical calculations. We found that multi-nanofilaments are involved in the low resistance state and the nanofilaments become thin and rupture separately in the RESET process with subsequent increase of the rupture gaps. Theoretical calculations reveal the role of oxygen vacancy amount in the evolution of Ni nanofilaments. We also demonstrate electromagnetic coupling in this system, which opens a new avenue for multifunctional devices.Resistive switching effect in conductor/insulator/conductor thin-film stacks is promising for resistance random access memory with high-density, fast speed, low power dissipation and high endurance, as well as novel computer logic architectures. NiO is a model system for the resistive switching effect and the formation/rupture of Ni nanofilaments is considered to be essential. However, it is not clear how the nanofilaments evolve in the switching process. Moreover, since Ni nanofilaments should be ferromagnetic, it provides an opportunity to explore the electromagnetic coupling in this system. Here, we report a direct observation of Ni nanofilaments and their specific evolution process for the first time by a combination of various measurements and theoretical calculations. We found

  14. La niña proletaria

    Directory of Open Access Journals (Sweden)

    Cartabia, Sabrina A.

    2011-12-01

    Full Text Available El presente trabajo se propone trazar un paralelo entre el cuento de Osvaldo Lamborghini “El niño proletario”, el cual, según la autora del ensayo, introduce al lector en la lucha de clases y el sometimiento de los/as proletarios/as, que sufren las mujeres, en particular a través de la violencia sexual. De esa forma la autora se pregunta si el poder que ciertas clases detentan sobre otras no influye también sobre el sometimiento de la mujer. El ensayo analiza además cómo la violencia sexual es una herramienta que constituye la base de la desigualdad, el sometimiento y la degradación de la mujer, al igual que constituye una herramienta de opresión de otros grupos vulnerables como los niños y niñas.

  15. [NiFeSe]-hydrogenase chemistry.

    Science.gov (United States)

    Wombwell, Claire; Caputo, Christine A; Reisner, Erwin

    2015-11-17

    The development of technology for the inexpensive generation of the renewable energy vector H2 through water splitting is of immediate economic, ecological, and humanitarian interest. Recent interest in hydrogenases has been fueled by their exceptionally high catalytic rates for H2 production at a marginal overpotential, which is presently only matched by the nonscalable noble metal platinum. The mechanistic understanding of hydrogenase function guides the design of synthetic catalysts, and selection of a suitable hydrogenase enables direct applications in electro- and photocatalysis. [FeFe]-hydrogenases display excellent H2 evolution activity, but they are irreversibly damaged upon exposure to O2, which currently prevents their use in full water splitting systems. O2-tolerant [NiFe]-hydrogenases are known, but they are typically strongly biased toward H2 oxidation, while H2 production by [NiFe]-hydrogenases is often product (H2) inhibited. [NiFeSe]-hydrogenases are a subclass of [NiFe]-hydrogenases with a selenocysteine residue coordinated to the active site nickel center in place of a cysteine. They exhibit a combination of unique properties that are highly advantageous for applications in water splitting compared with other hydrogenases. They display a high H2 evolution rate with marginal inhibition by H2 and tolerance to O2. [NiFeSe]-hydrogenases are therefore one of the most active molecular H2 evolution catalysts applicable in water splitting. Herein, we summarize our recent progress in exploring the unique chemistry of [NiFeSe]-hydrogenases through biomimetic model chemistry and the chemistry with [NiFeSe]-hydrogenases in semiartificial photosynthetic systems. We gain perspective from the structural, spectroscopic, and electrochemical properties of the [NiFeSe]-hydrogenases and compare them with the chemistry of synthetic models of this hydrogenase active site. Our synthetic models give insight into the effects on the electronic properties and reactivity of

  16. Two-proton radioactivity of 48Ni

    Science.gov (United States)

    Miernik, Krzysztof

    2011-10-01

    In experiment performed at NSCL facility we studied the decay of extremely neutron deficient isotope of 48Ni. Ions were implanted into a gaseuos detector, the Optical Time Projection Chamber which allows to record tracks of charged particles. Six events of 48Ni were observed, the two-proton radioactivity (four events) and the β-decay (two events) channels were clearly indentified. The half-life of 48Ni is determined to be T1 / 2 = 2.1-0. 4 + 1 . 4 ms. The results of three-dimensional events reconstruction as well as comparison of results with theoretical models will be presented. Research performed as a Eugene P. Wigner Fellow and staff member at the Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the U.S. Department of Energy under Contract DE-AC05-00OR22725.

  17. Voz del niño

    OpenAIRE

    Urra-Barandiarán, A. (Ainhoa); Vázquez-de-la-Iglesia, F. (Francisco); Fernandez-Gonzalez, S. (Secundino); Molina, M.T.

    2006-01-01

    En el curso de la vida la voz sufre diferentes cambios que obedecen a factores de desarrollo y en los que intervienen de manera decisiva el sistema nervioso y el sistema hormonal. La voz del niño y, por tanto la disfonía en el niño requiere una evaluación precisa y específica, no sólo desde el punto de vista instrumental sino también perceptual y en evaluación logopédica. Se insiste en la protocolización de elaboración de trastornos de voz en el niño, la revisión de los f...

  18. Microstructure evolution of electroless Ni P and Ni Cu P deposits on Cu in the presence of additives

    Science.gov (United States)

    Lin, Kwang-Lung; Chang, Yu-Lan; Huang, Chiao-Chan; Li, Fang-I.; Hsu, Jen-Che

    2001-09-01

    The microstructures of electroless Ni-P and Ni-Cu-P deposits were investigated in the presence of thiourea and saccharin with AFM. The phosphorus contents and crystallinity of the deposits were investigated. Saccharin was found to refine the nodular structure of the Ni-Cu-P deposit, while not affecting the P% of the Ni-P and Ni-Cu-P deposits. On the other hand, thiourea was found to affect the P% and surface roughness of the Ni-P deposit. Thiourea does not exhibit nodular refining effect on the deposit.

  19. The acceleration intermediate phase (NiS and Ni3S2) evolution by nanocrystallization in Li/NiS2 thermal batteries with high specific capacity

    Science.gov (United States)

    Jin, Chuanyu; Zhou, Lingping; Fu, Licai; Zhu, Jiajun; Li, Deyi; Yang, Wulin

    2017-06-01

    The intermediate phase of NiS2 is thought to be a bottleneck currently to improve the overall performance of Li/NiS2 thermal batteries because of its low conductivity and close formation enthalpy between NiS2 and the intermediate phase (NiS, Ni3S2, etc). For improving the discharge performances of Li/NiS2 thermal batteries, the nano NiS2 with an average size of 85 ± 5 nm is designated as a cathode material. The electrochemical measurements show that the specific capacity of nano NiS2 cathode is higher than micro NiS2. The nano NiS2 cathode exhibits excellent electrochemical performances with high specific capacities of 794 and 654 mAh g-1 at current density of 0.1 and 0.5 A cm-2 under a cut-off voltage of 0.5 V, respectively. These results show that the rapid intermediate phase evolution from the nanocrystallization can obviously enhance use efficiency of NiS2 and improve discharge performances of thermal batteries.

  20. Hierarchical NiCo2 S4 Nanotube@NiCo2 S4 Nanosheet Arrays on Ni Foam for High-Performance Supercapacitors.

    Science.gov (United States)

    Chen, Haichao; Chen, Si; Shao, Hongyan; Li, Chao; Fan, Meiqiang; Chen, Da; Tian, Guanglei; Shu, Kangying

    2016-01-01

    Hierarchical NiCo2 S4 nanotube@NiCo2 S4 nanosheet arrays on Ni foam have been successfully synthesized. Owing to the unique hierarchical structure, enhanced capacitive performance can be attained. A specific capacitance up to 4.38 F cm(-2) is attained at 5 mA cm(-2) , which is much higher than the specific capacitance values of NiCo2 O4 nanosheet arrays, NiCo2 S4 nanosheet arrays and NiCo2 S4 nanotube arrays on Ni foam. The hierarchical NiCo2 S4 nanostructure shows superior cycling stability; after 5000 cycles, the specific capacitance still maintains 3.5 F cm(-2) . In addition, through the morphology and crystal structure measurement after cycling stability test, it is found that the NiCo2 S4 electroactive materials are gradually corroded; however, the NiCo2 S4 phase can still be well-maintained. Our results show that hierarchical NiCo2 S4 nanostructures are suitable electroactive materials for high performance supercapacitors. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Radiation damage buildup and dislocation evolution in Ni and equiatomic multicomponent Ni-based alloys

    Science.gov (United States)

    Levo, E.; Granberg, F.; Fridlund, C.; Nordlund, K.; Djurabekova, F.

    2017-07-01

    Single-phase multicomponent alloys of equal atomic concentrations (;equiatomic;) have proven to exhibit promising mechanical and corrosion resistance properties, that are sought after in materials intended for use in hazardous environments like next-generation nuclear reactors. In this article, we investigate the damage production and dislocation mobility by simulating irradiation of elemental Ni and the alloys NiCo, NiCoCr, NiCoFe and NiFe, to assess the effect of elemental composition. We compare the defect production and the evolution of dislocation networks in the simulation cells of two different sizes, for all five studied materials. We find that the trends in defect evolution are in good agreement between the different cell sizes. The damage is generally reduced with increased alloy complexity, and the dislocation evolution is specific to each material, depending on its complexity. We show that increasing complexity of the alloys does not always lead to decreased susceptibility to damage accumulation under irradiation. We show that, for instance, the NiCo alloy behaves very similarly to Ni, while presence of Fe or Cr in the alloy even as a third component reduces the saturated level of damage substantially. Moreover, we linked the defect evolution with the dislocation transformations in the alloys. Sudden drops in defect number and large defect fluctuations from the continuous irradiation can be explained from the dislocation activity.

  2. Tipos especiales de niños

    Directory of Open Access Journals (Sweden)

    Mercedes Rodrigo Bellido

    1946-09-01

    Full Text Available En las tres últimas lecciones han sido expuestas algunas consideraciones referentes a niños y adolescentes desde el nacimiento hasta el dintel de la juventud. En todas ellas hemos procurado poner de relieve la necesidad de individualizar el conocimiento de cada niño para obtener mejores resultados en su adaptación a su futura vida de adultos, En todas ellas  nos hemos referido al llamado niño normal. Nos corresponde en la lección de hoy ocuparnos can la superficialidad característica de estas charlas tipo-muestrario, de otras categorías de niños muy dignos de interés.. quienes unas por exceso, otros por defecto, otros por dificultades de adaptación por diferentes causas, se desvían de la línea media de la normalidad. Consideramos que no está fuera del lugar, aquí, el tema de los niños excepcionales y por el contrario que es necesario intensificar el estudio de los trastornos de la vida mental y emocional de los niños en la preparación de los estudiantes de Medicina. Y no es nuestra solo esta opinión; no hace mucho tiempo en la Medical School de Ia Universidad de Minnessota hemos sabido que se ha hecho un intento de considerar y evaluar factores emocionales ambientales sobre las mismas bases que los descubrimientos fisiológicos.

  3. Ni Foam-Ni3 S2 @Ni(OH)2 -Graphene Sandwich Structure Electrode Materials: Facile Synthesis and High Supercapacitor Performance.

    Science.gov (United States)

    Wang, Xiaobing; Hu, Jiangjiang; Su, Yichang; Hao, Jin; Liu, Fanggang; Han, Shuang; An, Jian; Lian, Jianshe

    2017-03-23

    A novel Ni foam-Ni3 S2 @Ni(OH)2 -graphene sandwich-structured electrode (NF-NN-G) with high areal mass loading (8.33 mg cm(-2) ) has been developed by sulfidation and hydrolysis reactions. The conductivity of Ni3 S2 and Ni(OH)2 were both improved. The upper layer of Ni(OH)2 , covered with a thin graphene film, is formed in situ from the surface of the lower layer of Ni3 S2 , whereas the Ni3 S2 grown on Ni foam substrate mainly acts as a rough support bridging the Ni(OH)2 and Ni foam. The graphene stabilized the Ni(OH)2 and the electrochemical properties were effectively enhanced. The as-synthesized NF-NN-G-5mg electrode shows a high specific capacitance (2258 F g(-1) at 1 A g(-1) or 18.81 F cm(-2) at 8.33 mA cm(-2) ) and an outstanding rate property (1010 F g(-1) at 20 Ag(-1) or 8.413 F cm(-2) at 166.6 mA cm(-2) ). This result is around double the capacitance achieved in previous research on Ni3 S2 @Ni(OH)2 /3DGN composites (3DGN=three-dimensional graphene network). In addition, the as-fabricated NF-NN-G-5mg composite electrode has an excellent cycle life with no capacitance loss after 3000 cycles, indicating a potential application as an efficient electrode. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. NiTi Expansion in Operated Unilateral Cleft Palate Patients

    Directory of Open Access Journals (Sweden)

    K Y Poornima

    2011-01-01

    Conclusion : NiTi expansion in operated cleft patients, showed mainly orthodontic expansion. The significant change in the maxillary inter- molar region is due to the direct placement of NiTi palatal expander to 16, 26.

  5. Funciones cognoscitivas en niños y niñas con trastorno disocial comparados con niños y niñas sin el trastorno

    OpenAIRE

    Urazán Torres, Gina Rocio

    2011-01-01

    Este proyecto de investigación tuvo como objetivo evaluar y caracterizar las funciones cognoscitivas de un grupo de niños y niñas con Trastorno Disocial (TD), comparándolas con las de un grupo de niños y niñas normales. Se utilizó un diseño de casos y controles con una muestra de 39 niños y niñas entre 6 y 12 años de edad con TD y 39 niños y niñas del mismo rango de edades y los mismos estratos socioeconómicos. Los participantes fueron seleccionados de diferentes instituciones educativas de B...

  6. Enhancement of porous silicon photoluminescence using (Ni) treatment

    Science.gov (United States)

    Nabil, M.; Elnouby, M.; Gayeh, N.; Sakr, A. H.; Motaweh, H. A.

    2017-10-01

    A new method has been developed to improve the photoluminescence intensity of porous silicon (PS). Self-organized (PS) can be used in various fields. The deposition of metal nanoparticles (Ni) allows utilizing the obtained nano-composite for numerous applications such as sensor technology, biomedicine, and many more. (Ni/PS) nano-composite powders are prepared using Ni deposition on the PS powder surface. The (Ni/PS) powders became hydrophilic by the deposited Ni nanoparticles. At the different percentages of (Ni: PS), at a higher percentage than (3:1) the values of the crystallite size of Ni and PS are nearly equivalent which suggests the saturation case of PS surface by Ni particles. It also depends on the deposition time value. In this study, that is the commercialization of nanostructured materials, it is important that the manufacturing costs are appropriate and inexpensive for large scale production, in addition, the enhancement of the photoluminescence intensity of (PS).

  7. Hydrogenation of Ethyl Acetate to Ethanol over Ni-Based Catalysts Obtained from Ni/Al Hydrotalcite-Like Compounds

    Directory of Open Access Journals (Sweden)

    Longfei Jiang

    2010-07-01

    Full Text Available A series of Ni-based catalysts were prepared using hydrogen reduction of Ni/Al hydrotalcite-like compounds (Ni/Al HTlcs synthesized by coprecipitation. The physico-chemical properties of Ni/Al hydrotalcite-like compounds and the corresponding Ni-based catalysts were characterized using inductively coupled plasma (ICP, BET surface areas, X-ray diffraction (XRD, Fourier transform infrared (FTIR spectroscopy and scanning electron microscopy (SEM techniques. The results indicated that Ni/Al HTlcs with layered structures could be successfully prepared by the coprecipitation method, and the characteristic HTlcs reflections were also observed in the XRD analysis. The NiO and Ni0 phases were identified in all Ni-based catalysts, which displayed randomly interconnected pores and no layer structures. In addition, the studies also found the Ni/Al HTlcs and Ni-based catalysts had high specific surface areas, low pore volumes and low pore diameters. The catalytic hydrogenation of ethyl acetate to ethanol with Ni-based catalysts was also investigated. Among the studied catalysts, RE1NASH-110-3 showed the highest selectivity and yield of ethyl acetate to ethanol, which were 68.2% and 61.7%, respectively. At the same time, a major by-product, butyl acetate, was formed due to an ester-exchange reaction. A proposed hydrogenation pathway for ethyl acetate over Ni-based catalysts was suggested.

  8. Structural study of radiolytic catalysts Ni-Ce/Al2O3 and Ni-Pt/Al2O3

    Science.gov (United States)

    Seridi, F.; Chettibi, S.; Keghouche, N.; Beaunier, P.; Belloni, J.

    2017-01-01

    Ni-Ce and Ni-Pt bimetallic catalysts supported over α-Al2O3 are synthesized by using co-impregnation method, and then reduced, each via radiolytic process or thermal H2-treatment. For Ni-Ce/Al2O3, the structural study reveals that Ce is alloyed with Ni as Ce2Ni7 nanoparticles in the radiation-reduced catalysts, while it segregates to the surface in the form of CeO2 in the H2-reduced catalysts. For Ni-Pt/Al2O3 radiolytic catalysts, Ni, Pt, NiPt and Ni3Pt nanoparticles, which size is 3.5 nm, are observed. When the radiation-reduced samples are tested in the benzene hydrogenation, they both display high conversion rate. However, the Ni-Pt/Al2O3 is more efficient than Ni-Ce/Al2O3. The performance of the catalysts is correlated with the high dispersion of the metal and the presence of intermetallic Ni-Pt and Ni-Ce phases. It is compared to that of other radiolytic monometallic/oxide catalysts of the literature.

  9. Melting in the Fe-Ni system

    Science.gov (United States)

    Lord, O. T.; Walter, M. J.; Vocadlo, L.; Wood, I. G.; Dobson, D. P.

    2012-12-01

    The melting temperature of the Fe-rich core alloy at the inner core boundary (ICB) condition of 330 GPa is a key geophysical parameter because it represents an anchor point on the geotherm. An accurate knowledge of the melting curves of candidate alloys is therefore highly desirable. In spite of this, there is still considerable uncertainty in the melting point even of pure Fe at these conditions; estimates range from as low as 4850K based on one laser heated diamond anvil cell (LHDAC) study [1] to as high as 6900K based on recent quantum Monte Carlo calculations [2]. In reality we expect that the bulk core alloy may contain 5-10 wt% Ni (based on cosmochemical and meteoritic arguments) and up to 10 wt% of an as yet undetermined mix of light elements (with Si, S, C and O being the most likely candidates). While some recent studies have looked at the effects of light elements on the melting curve of Fe [e.g.: 3,4] with some of these studies including a small amount of Ni in their starting material, to date there has been no systematic study of melting temperatures in the Fe-Ni system. To address this issue, we have embarked upon just such a study. Using the LHDAC we have determined the melting curve of the pure Ni end-member to 180 GPa, and that of pure Fe to 50 GPa, using perturbations in the power vs. temperature function as the melting criterion [5]. Ar or NaCl were employed as pressure media while temperature was measured using standard spectroradiometric techniques [6]. In the case of Ni, perturbations were observed for both the sample and the Ar medium, allowing us to determine the melting curve of Ar and Ni simultaneously. Our results thus far for Ni and Ar agree closely with all of the available data, while extending the melting curves by a factor of two in pressure. In the case of Fe, our current dataset is also in good agreement with previous studies [2,7]. The agreement of all three melting curves with the literature data as well as other materials

  10. NiO Nanofibers as a Candidate for a Nanophotocathode

    Directory of Open Access Journals (Sweden)

    Thomas J. Macdonald

    2014-04-01

    Full Text Available p-type NiO nanofibers have been synthesized from a simple electrospinning and sintering procedure. For the first time, p-type nanofibers have been electrospun onto a conductive fluorine doped tin oxide (FTO surface. The properties of the NiO nanofibers have been directly compared to that of bulk NiO nanopowder. We have observed a p-type photocurrent for a NiO photocathode fabricated on an FTO substrate.

  11. Facile synthesis of monodisperse thermally immiscible Ag–Ni alloy ...

    Indian Academy of Sciences (India)

    Administrator

    to their synergistic effects. Using Ag–Ni ANPs, at the same time, is more economical than pure silver ANPs. According to the literature, metal-catalyst decoration can .... 1451. Figure 7. Schematic representation of the Ag–Ni ANP forma- tion. M stands for a metal element. Schematic representation of the Ag–Ni ANP formation.

  12. Fabrication of micro-Ni arrays by electroless and electrochemical ...

    Indian Academy of Sciences (India)

    Nickel micro-arrays were fabricated by electroless and electrochemical deposition in an etched porous aluminum membrane. The aluminum membrane with metal characteristic could be fabricated from high-purity aluminium by electrochemical method. The aluminum reduced Ni2+ into Ni and the formed Ni nuclei served as ...

  13. Optimization of process parameters for synthesis of silica–Ni ...

    Indian Academy of Sciences (India)

    The optimumcombination of experimental variable, temperature, time of heat treatment under nitrogen atmosphere and amount of Ni-salt was delineated to find out the maximum yield of nanophase Ni in the silica gel matrix. The size of Ni in the silica gel was found to be 34 and 45 nm for the two chosen compositions, ...

  14. Energetic Mapping of Ni Catalysts by Detailed Kinetic Modeling

    DEFF Research Database (Denmark)

    Bjørgum, Erlend; Chen, De; Bakken, Mari G.

    2005-01-01

    Temperature-programmed desorption (TPD) of CO has been performed on supported and unsupported nickel catalysts. The unsupported Ni catalyst consists of a Ni(14 13 13) single crystal which has been studied under ultrahigh vacuum conditions. The desorption energy for CO at low CO surface coverage w...... nicely with literature values, providing useful information for identifying active sites on supported Ni catalysts....

  15. New route for synthesis of electrocatalytic Ni (OH) 2 modified ...

    Indian Academy of Sciences (India)

    Immobilization of redox species like Ni(OH)2 onto the electrode surface is important in the application areas such as super capacitor, electrochromic displays and electrocatalysis. Nickel hexacyanoferrate (NiHCF) modified glassy carbon could be further derivatized with Ni(OH)2 by electrochemical cycling in alkali.

  16. Synthesis and characterization of Co–Ni and Fe–Ni alloy nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Solanki, Vandana [Discipline of Natural Sciences, Indian Institute of Information Technology, Design & Manufacturing Jabalpur, Dumna Airport Road, Madhya Pradesh 482005 (India); Lebedev, Oleg I. [Laboratoire CRISMAT, ENSICAEN UMR6508, 6 Bd Maréchal Juin, Cedex 4, Caen 14050 (France); ITMO University, 49 Kronverksky Pr., St. Petersburg 197101 (Russian Federation); Seikh, Md. Motin [Department of Chemistry, Visva-Bharati University, Santiniketan, West Bengal 731235 (India); Mahato, Nihar K. [Discipline of Natural Sciences, Indian Institute of Information Technology, Design & Manufacturing Jabalpur, Dumna Airport Road, Madhya Pradesh 482005 (India); Raveau, Bernard [Laboratoire CRISMAT, ENSICAEN UMR6508, 6 Bd Maréchal Juin, Cedex 4, Caen 14050 (France); Kundu, Asish K., E-mail: asish.k@gmail.com [Discipline of Natural Sciences, Indian Institute of Information Technology, Design & Manufacturing Jabalpur, Dumna Airport Road, Madhya Pradesh 482005 (India)

    2016-12-15

    The magnetic alloy nanoparticles have been synthesized by sol-gel method with a stable Pm-3m cubic structure. The Co–Ni and Fe–Ni alloy nanoparticles are highly crystalline and exhibit preferential low index <111> faceting as determined from HRTEM investigation. TEM images and EDX elemental mapping also confirm the nano-dimensional structure with core-shell structure, where the alloy forms the core and the shell is formed by amorphous carbon. The magnetization results of the alloy nanoparticles confirm the ferromagnetic nature at room temperature akin to their bulk metals with a significant value of field dependent isothermal magnetization at high temperature (390 K). - Highlights: • Synthesis of Co–Ni and Fe–Ni alloy nanoparticles by exploiting low temperature sol–gel process. • The nanoparticles are core–shell type with core ferromagnetic alloys and graphitic carbon shell. • Electron microscope study explains the higher stability at ambient conditions of the nanoparticles.

  17. Thermal stability of electrodeposited Ni and Ni-Co layers; an EBSD-study

    DEFF Research Database (Denmark)

    Rasmussen, Anette Alsted; Gholinia, A.; Trimby, P.W.

    2004-01-01

    The influence of heat treatment on the microstructure and the microtexture of electrodeposited Ni and Ni-Co layers was investigated with Electron Backscatter Diffraction (EBSD) with high resolution. Samples were annealed for 1 hour at 523 K and 673 K, the temperature region wherein recrystallisat......The influence of heat treatment on the microstructure and the microtexture of electrodeposited Ni and Ni-Co layers was investigated with Electron Backscatter Diffraction (EBSD) with high resolution. Samples were annealed for 1 hour at 523 K and 673 K, the temperature region wherein...... recrystallisation occurs. The results are discussed in relation to the resolution of EBSD for the very fine grained electrodeposits and previous X-ray diffracton investigations....

  18. Modelling of rechargeable NiMH batteries

    NARCIS (Netherlands)

    Ledovskikh, A.; Verbitskiy, E.; Ayeb, A.; Notten, P.H.L.

    2003-01-01

    A new mathematical model has been developed for rechargeable NiMH batteries, which is based on the occurring physical–chemical processes inside. This model enables one to simultaneously simulate the battery voltage, internal gas pressures (both PO2 and PH2) and temperature during battery operation.

  19. Ni (II) decorated nano silicoaluminophosphate molecular sieves ...

    Indian Academy of Sciences (India)

    Ni(II) decorated nano silicoaluminophosphate molecular sieves-modified carbon paste electrode as an electrocatalyst for electrooxidation of methanol ... of Science, Babol University of Technology, Babol 47148-71167, Iran; Biofuel & Renewable Energy Research Center, Faculty of Chemical Engineering, Babol University ...

  20. Cancer en los niños

    OpenAIRE

    Pereira, Fabio; Ramírez Wurttenberger, Óscar; Lotero, Viviana; Fundación Valle de Lili

    2004-01-01

    Epidemiología/ ¿Por qué se presenta el cáncer en los niños?/ ¿Cómo se realiza el diagnóstico?/ ¿Cómo es el tratamiento?/ ¿Resultados del tratamiento?/Recomendaciones/Otras formas de tratamiento: El trasplante de médula ósea.

  1. (ii) and ni (ii) complexes with n

    African Journals Online (AJOL)

    DR. AMINU

    II) complexes with a. Schiff base derived from. 4-dimetylamino benzaldehyde and primary amines. The chemical analysis data showed the formation of (1:1) metal - ligand ratio and a square planar geometry was suggested for Co(II) and Ni(II) ...

  2. Dissociative chemisorption of methane on Ni(111)

    NARCIS (Netherlands)

    Krishna Mohan, Gangadharan Prasanna

    2010-01-01

    In this thesis we attempt to understand several aspects of the gas-surface physics/chemistry of (a) the dissociative chemisorption of CH4 on the Ni(111) surface and (b) N2 dissociation over the Ru(0001) surface. Apart from their industrial importance, these systems are regarded as prototypes for

  3. Preparing of Ni-Cu-P Coating

    Science.gov (United States)

    Shumei, Kang

    Ni-Cu-P coating by chemical plating has excellent corrosion resistance,wear resistance, thermal stability and electrical conductivity. In this paper, Ni-Cu-P was prepared by chemical deposition methods, the optimum process of chemical plating Ni-Cu-P. By using scanning electron microscopy(SEM), spectrum analyzer, Autolab workstation on the corrosion resistance of the coating. The results showed that: (1)after the specimen surface chemical plating nickelcopper phosphorus treatment, in the same corrosion potential, the corrosion current density was lower than that of Ni-P coating and substrate materials; (2)had a significant effect on corrosion resistance of quantity of citric acid sodium on nickel copper phosphorus alloy plating, coating corrosion resistance with increasing citric acid sodium content first increased and then decreased, and inaddition level of sodium citrate is 40g/L, the corrosion current density reaches a minimum, 14.51×10-6A/cm2; (3)under the same conditions, the Ni-Cu-P alloy coating pH impact is the biggest,the maximum impedance 1268.05Ω; (4)in the 3.5%NaCl solution, with the change of copper content, the main trend of the corrosion current is decreased first and then increased, and the content of copper in Energy spectrum analysis within 5.18Wt% corrosion current density of a minimum of 14.51×10-6A/cm2, the corrosion resistance. With the increase of Cu content in the coatings, the P content first increased and then decreased in the coating, the content of Ni decreased first and then increased; (5)the best technology:NiSO46H2O, CuSO4 25g/L, 5H2O 0.15g/L, C6H5Na3O7•2H2O 40g/L, NaH2PO2H2O 25g/L, CH3COONa 15g/L, KIO3 0.03g/L, C12H25NaO4SO3 0.01g/L, pH4.75 ± 0.01,temperature 80 ± 1 °C, deposition time of 2h.

  4. Elastic scattering of sup 58 Ni+ sup 64 Ni near the Coulomb barrier

    Energy Technology Data Exchange (ETDEWEB)

    Stefanini, A.M.; Xu Jincheng; Corradi, L.; Montagnoli, G.; Moreno, H.; Nagashima, Y.; Mueller, L.; Narayanasamy, M.; Napoli, D.R.; Spolaore, P. (Istituto Nazionale di Fisica Nucleare, Padua (Italy). Lab. di Legnaro); Beghini, S.; Scarlassara, F.; Segato, G.F.; Soramel, F. (Padua Univ. (Italy). Dipt. di Fisica Istituto Nazionale di Fisica Nucleare, Padua (Italy)); Signorini, C. (Salerno Univ. (Italy). Dipt. di Fisica Istituto Nazionale di Fisica Nucleare, Padua (Italy)); Esbensen, H.; Landowne, S. (Argonne National Lab., IL (USA). Physics Div.); Pollarolo, G. (Turin Univ. (Italy). Dipt. di Fisica Istituto Nazionale di Fisica Nucleare, Turin (Italy))

    1990-04-26

    Elastic scattering angular distributions have been measured for {sup 58}Ni+{sup 64}Ni at three energies around the Coulomb barrier employing a new kinematic coincidence technique. The data are compared with the results of coupled-channels calculations including inelastic excitations as well as one- and two-neutron transfer reactions. The agreement is good and the calculations also agree well with the available transfer and fusion reaction data. (orig.).

  5. Geometric structures of thin film: Pt on Pd(110) and NiO on Ni(100)

    Energy Technology Data Exchange (ETDEWEB)

    Warren, Oden L. [Iowa State Univ., Ames, IA (United States)

    1993-07-01

    This thesis is divided into 3 papers: dynamical low-energy electron- diffraction investigation of lateral displacements in topmost layer of Pd(110); determination of (1x1) and (1x2) structures of Pt thin films on Pd(110) by dynamical low-energy electron-diffraction analysis; and structural determination of a NiO(111) film on Ni(100) by dynamical low-energy electron-diffraction analysis.

  6. Effect of deposition technique of Ni on the perpendicular magnetic anisotropy in Co/Ni multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Akbulut, S., E-mail: sakbulut@gtu.edu.tr [Gebze Technical University, Physics Department, Istanbul Cad, PK 41400 Gebze/Kocaeli (Turkey); Akbulut, A. [Gebze Technical University, Physics Department, Istanbul Cad, PK 41400 Gebze/Kocaeli (Turkey); Özdemir, M. [Marmara University, Physics Department, Göztepe, Istanbul (Turkey); Yildiz, F., E-mail: fyildiz@gtu.edu.tr [Gebze Technical University, Physics Department, Istanbul Cad, PK 41400 Gebze/Kocaeli (Turkey)

    2015-09-15

    The perpendicular magnetic anisotropy (PMA) of Si/Pt 3.5/(Co 0.3/Ni 0.6){sub n} /Co 0.3/ Pt 3 (all thicknesses are nm) multilayers were investigated for two different sample sets by using ferromagnetic resonance (FMR) and magnetooptic Kerr effect (MOKE) techniques. In the first sample set all layers (buffer, cap, Co and Ni) were grown by magnetron sputtering technique while in the second sample set Ni sub-layers were grown by molecular beam epitaxy (MBE) at high vacuum. Apart from deposition technique of Ni, all other parameters like thicknesses and growth rates of each layers are same for both sample sets. Multilayers in these two sample sets display PMA in the as grown state until a certain value of bilayer repetition (n) and the strength of PMA decreases with increasing n. Magnetic easy axis's of the multilayered samples switched from film normal to the film plane when n is 9 and 5 for the first and second sample sets, respectively. The reason for that, PMA was decreased due to increasing roughness with increasing n. This was confirmed by X Ray Reflectivity (XRR) measurements for both sample sets. Moreover, in the first sample set coercive field values are smaller than the second sample set, which means magnetic anisotropy is lower than the latter one. This stronger PMA is arising due to existence of stronger Pt (111) and Co/Ni (111) textures in the second sample set. - Highlights: • Effect of deposition techniques for Ni sub-layers on magnetic properties in [Co/Ni]{sub n} multilayered films was studied. • Ni sub-layers were deposited by two different techniques, molecular beam epitaxy (MBE) and magnetron sputtering. • Spin reorientation thickness and magnitude of the anisotropy are strongly depending on growing techniques.

  7. Epitaxial NiWO4 films on Ni(110): Experimental and theoretical study of surface stability

    Science.gov (United States)

    Doudin, N.; Pomp, S.; Blatnik, M.; Resel, R.; Vorokhta, M.; Goniakowski, J.; Noguera, C.; Netzer, F. P.; Surnev, S.

    2017-05-01

    Despite the application potential of nickel tungstate (NiWO4) in heterogeneous catalysis, humidity and gas sensing, etc, its surfaces have essentially remained unexplored. In this work, NiWO4 nanoparticles and films with the wolframite structure have been grown via a solid-state reaction of (WO3)3 clusters and a NiO(100) film on a Ni(110) crystal surface and characterized by a variety of experimental techniques, including x-ray photoelectron spectroscopy (XPS), scanning tunneling microscopy (STM) and x-ray diffraction (XRD), combined with ab-initio density functional theory (DFT) calculations. NiWO4 grows initially as three-dimensional (3D) crystalline nanoparticles displaying mainly two crystalline facets vicinal to the (100) surface, which merge with increasing the (WO3)3 coverage into a quasi-continuous epitaxial film. The DFT results provide an account of the energetics of NiWO4 low index surfaces and highlight the role of faceting in the stabilization of extended polar (100) terraces. These combined experimental and theoretical results show that interaction with a metal substrate and vertical confinement may stabilize oxide nano-objects with high energy facets, able to enhance their reactivity.

  8. Weldability of spheroidal graphite ductile cast iron using Ni / Ni-Fe electrodes

    Directory of Open Access Journals (Sweden)

    Pascual, M.

    2009-10-01

    Full Text Available Weldability of spheroidal graphite ductile cast iron was established using a cheap Ni-Fe and a high purity Ni electrode. A preheating treatment at 350 °C and an annealing treatment at 850 °C were carried out to improve mechanical properties of welded pieces. The pure Ni electrode showed graphite diffusion in the bead with a uniform distribution of phases, improving weldability and decreasing fragility. Preheating and annealing treatments increased ductility and improved weldability.

    Se establece la soldabilidad de funciones dúctiles de grafito según las características mecánicas alcanzadas, utilizando un electrodo puro de Ni mientras se compara con uno más económico de Ni-Fe. Diferentes tratamientos t��rmicos son propuestos y analizados. El electrodo de Ni puro mostró difusión de grafito desde el material original al cordón de soldadura, dando como resultado una fase homogénea que mejoró la soldabilidad y redujo la fragilidad. Un pre tratamiento a 350 °C y un recocido a 850 °C incrementaron la ductilidad y mejoró la soldabilidad.

  9. Cold Spray Deposition of Ni and WC-Reinforced Ni Matrix Composite Coatings

    Science.gov (United States)

    Alidokht, S. A.; Vo, P.; Yue, S.; Chromik, R. R.

    2017-09-01

    Ni-WC composites are ideal protective coatings against wear and are often fabricated using laser cladding and thermal spray processes, but the high temperatures of these processes result in decarburization, which deteriorates the performance of the coating. Cold spray has the potential to deposit Ni-WC composite coatings and retain the composition of the initial WC feedstock. However, the insignificant plastic deformation of hard WC particles makes it difficult to build up a high WC content coating by cold spray. By using three different WC powder sizes, the effect of feedstock powder size on WC retention was tested. To improve WC retention, a WC/Ni composite powder in mixture with Ni was also sprayed. Microstructural characterization, including the deformed structure of Ni splats, retention, distribution, and fragmentation of WC, was performed by scanning electron microscopy. An improvement in WC retention was achieved using finer WC particles. Significant improvement in WC particles retention was achieved using WC/Ni composite powder, with the WC content in the coating being close to that of the feedstock.

  10. Interfacial reaction of Ni{sub 3}Sn{sub 4} intermetallic compound in Ni/SnAg solder/Ni system under thermomigration

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yi-Shan; Yang, Chia-Jung; Ouyang, Fan-Yi, E-mail: fyouyang@ess.nthu.edu.tw

    2016-07-25

    The growth of Ni{sub 3}Sn{sub 4} intermetallic compound (IMC) between liquid–solid interface in micro-scale Ni/SnAg/Ni system was investigated under a temperature gradient of 160 °C/cm at 260 °C on a hot plate. In contrast to a symmetrical growth of Ni{sub 3}Sn{sub 4} on both interfaces under isothermally annealed at 260 °C, the interfacial Ni{sub 3}Sn{sub 4} IMC exhibited asymmetric growth under a temperature gradient; the growth of Ni{sub 3}Sn{sub 4} at cold interface was faster than that at hot side because of temperature gradient induced mass migration of Ni atoms from the hot end toward the cold end. It was found that two-stage growth behavior of Ni{sub 3}Sn{sub 4} IMC under a temperature gradient. A growth model was established and growth kinetic analysis suggested that the chemical potential gradient controlled the growth of Ni{sub 3}Sn{sub 4} at stage I (0–120 min) whereas the dynamic equilibrium between chemical potential gradient and temperature gradient forces was attained at the hot end at stage II (120–210 min). When dynamic equilibrium was achieved at 260 °C, the critical length-temperature gradient product at the hot end was experimentally estimated to be 489.18 μm × °C/cm and the moving velocity of Ni{sub 3}Sn{sub 4} interface due to Ni consumption was calculated to be 0.134 μm/h. The molar heat of transport (Q*) of Ni atoms in molten SnAg solder was calculated to be +0.76 kJ/mol. - Highlights: • Interfacial reaction in Ni/SnAg solder/Ni system under thermal gradient. • Growth rate of Ni{sub 3}Sn{sub 4} at cold end is faster than that at hot end. • Critical length-temperature gradient product at hot end is 489.2 μm°C/cm at 260 °C. • Velocity of Ni{sub 3}Sn{sub 4} moving interface is 0.134 μm/h during dynamic equilibrium. • Molar heat of transport (Q*) of Ni in molten SnAg was +0.76 kJ/mol.

  11. Microstructure, Mechanical Property, and Phase Transformation of Quaternary NiTiFeNb and NiTiFeTa Shape Memory Alloys

    National Research Council Canada - National Science Library

    Yulong Liang; Shuyong Jiang; Yanqiu Zhang; Junbo Yu

    2017-01-01

    Based on ternary Ni45Ti51.8Fe3.2 (at %) shape memory alloy (SMA), Nb and Ta elements are added to an NiTiFe SMA by replacing Ni element, and consequently quaternary Ni44Ti51.8Fe3.2Nb1 and Ni44Ti51.8Fe3.2Ta1...

  12. Evaluation of the Antitumor Activity by Ni Nanoparticles with Verbascoside

    Directory of Open Access Journals (Sweden)

    Mingyue Chen

    2013-01-01

    Full Text Available Verbascoside (VB has attracted a great deal of attention due to ITS pharmacological properties. In our study, we synthesized a multifunctional verbascoside coated Ni nanoparticles (VB-Ni. Transmission electron microscopy (TEM and high performance liquid chromatography (HPLC display the characteristics of VB-Ni nanoparticles. Compared with VB, VB-Ni has been proven to induce apoptosis and resist the growth of doxorubicin-resistant K562 cells in vitro and in vivo. Thus, VB-Ni nanoparticles can be thought of as an ideal mode of cancer treatment.

  13. Atomistic modeling of ternary additions to NiTi and quaternary additions to Ni-Ti-Pd, Ni-Ti-Pt and Ni-Ti-Hf shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Mosca, H.O., E-mail: hmosca@cnea.gov.ar [Gcia. Investigacion y Aplicaciones, CNEA, Av. Gral Paz 1499, B1650KNA San Martin (Argentina); GCMM, UTN, FRG Pacheco, Av. H. Yrigoyen 288, Gral. Pacheco (Argentina); Bozzolo, G. [Loyola University Maryland, 4501 N. Charles St., Baltimore, MD 21210 (United States); Grosso, M.F. del [Gcia. Investigacion y Aplicaciones, CNEA, Av. Gral Paz 1499, B1650KNA San Martin (Argentina); GCMM, UTN, FRG Pacheco, Av. H. Yrigoyen 288, Gral. Pacheco (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas, CONICET (Argentina)

    2012-08-15

    The behavior of ternary and quaternary additions to NiTi shape memory alloys is investigated using a quantum approximate method for the energetics. Ternary additions X to NiTi and quaternary additions to Ni-Ti-Pd, Ni-Ti-Pt, and Ni-Ti-Hf alloys, for X=Au, Pt, Ir, Os, Re, W, Ta,Ag, Pd, Rh, Ru, Tc, Mo, Nb, Zr, Zn, Cu, Co, Fe, Mn, V, Sc, Si, Al and Mg are considered. Bulk properties such as lattice parameter, energy of formation, and bulk modulus of the B2 alloys are studied for variations due to the presence of one or two simultaneous additives.

  14. Nanoporous PdNi/C electrocatalyst prepared by dealloying high-Ni-content PdNi alloy for formic acid oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Wei; Wang, Hui; Wang, Rongfang [Key Laboratory of Eco-Environment-Related Polymer Materials, Ministry of Education of China, Key Laboratory of Gansu Polymer Materials, College of Chemistry and Chemical Engineering, Northwest Normal University, Lanzhou 730070 (China); Ji, Shan [South African Institute for Advanced Materials Chemistry, University of the Western Cape, Cape Town 7535 (South Africa)

    2012-12-15

    To improve the electrochemical performance of Pd-based catalysts for formic acid oxidation, a carbon supported nanoporous PdNi catalyst is prepared by dealloying high-Ni-content PdNi alloy nanoparticles in acid solution. The structure of nanoporous PdNi/C catalyst is characterized by X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy. The electrocatalytic results show that the activity of the nanoporous PdNi/C catalyst is higher than that of nonporous Pd/C catalyst. The results demonstrate that the carbon-supported nanoporous PdNi catalyst has a potential for application in direct formic acid fuel cells. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  15. State of Supported Nanoparticle Ni during Catalysis in Aqueous Media

    Energy Technology Data Exchange (ETDEWEB)

    Chase, Zizwe; Vjunov, Aleksei; Fulton, John; Camaioni, Donald; Balasubramanian, Mahalingam; Lercher, Johannes

    2015-11-09

    The state of Ni supported on HZSM-5 zeolite, silica, and sulfonated carbon was studied during aqueous-phase catalysis of phenol hydrodeoxygenation using in situ extended X-ray absorption fine structure spectroscopy. On sulfonated carbon and HZSM-5 supports, NiO and Ni(OH)(2) were readily reduced to Ni-0 under reaction conditions (approximate to 35bar H-2 in aqueous phenol solutions containing up to 0.5wt.% phosphoric acid at 473K). In contrast, Ni supported on SiO2 was not stable in a fully reduced Ni-0 state. Water enables the formation of Ni-II phyllosilicate, which is more stable, that is, difficult to reduce, than either -Ni(OH)(2) or NiO. Leaching of Ni from the supports was not observed over a broad range of reaction conditions. Ni-0 particles on HZSM-5 were stable even in presence of 15wt.% acetic acid at 473K and 35bar H-2.

  16. Intra-specific variation in Ni tolerance, accumulation and translocation patterns in the Ni-hyperaccumulator Alyssum lesbiacum.

    Science.gov (United States)

    Adamidis, G C; Aloupi, M; Kazakou, E; Dimitrakopoulos, P G

    2014-01-01

    A hydroponic experiment was conducted to investigate inter-population variation in Ni tolerance, accumulation and translocation patterns in Alyssum lesbiacum. The in vitro results were compared to field data (soil bioavailable and leaf Ni concentrations) so as to examine any potential relationship between hydroponic and natural conditions. Seeds from the four major existing populations of A. lesbiacum were used for the cultivation of plantlets in solution cultures with incrementally increasing Ni concentrations (ranging from 0 to 250 μmol L(-1) NiSO4). Ni accumulation and tolerance of shoots and roots, along with initial seed Ni concentration for each population were measured. The ratio of root or shoot length of plantlets grown in NiSO4 solutions to root or shoot lengths of plantlets grown in the control solution was used as tolerance index. For the range of metal concentrations used, A. lesbiacum presented significant inter-population variation in Ni tolerance, accumulation and translocation patterns. Initial seed Ni concentration was positively correlated to shoot Ni accumulation. A significant positive relationship between tolerance and accumulation was demonstrated. Initial seed Ni concentration along with physiological differences in xylem loading and Ni translocation of each population, appear to be the determining factors of the significant inter-population variation in Ni tolerance and accumulation. Our results highlight the inter-population variation in Ni tolerance and accumulation patterns in the Ni-hyperaccumulator A. lesbiacum and give support to the suggestion that the selection of metal hyperaccumulator species with enhanced phytoremediation efficiency should be considered at the population level. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. NiCo2S4 nanosheet-decorated 3D, porous Ni film@Ni wire electrode materials for all solid-state asymmetric supercapacitor applications.

    Science.gov (United States)

    Saravanakumar, Balasubramaniam; Jayaseelan, Santhana Sivabalan; Seo, Min-Kang; Kim, Hak-Yong; Kim, Byoung-Suhk

    2017-12-07

    Wire type supercapacitors with high energy and power densities have generated considerable interest in wearable applications. Herein, we report a novel NiCo2S4-decorated 3D, porous Ni film@Ni wire electrode for high performance supercapacitor application. In this work, a facile method is introduced to fabricate a 3D, porous Ni film deposited on a Ni wire as a flexible electrode, followed by decoration with NiCo2S4 as an electroactive material. The fabricated NiCo2S4-decorated 3D, porous Ni film@Ni wire electrode displays a superior performance with an areal and volumetric capacitance of 1.228 F cm-2 and 199.74 F cm-3, respectively, at a current density of 0.2 mA cm-1 with a maximum volumetric energy and power density (EV: 6.935 mW h cm-3; PV: 1.019 W cm-3). Finally, the solid state asymmetric wire type supercapacitor is fabricated using the fabricated NiCo2S4-decorated 3D, porous Ni film@Ni wire as a positive electrode and N-doped reduced graphene oxide (N-rGO) as a negative electrode and this exhibits good areal and volumetric capacitances of CA: 0.12 F cm-2 and CV: 19.57 F cm-2 with a higher rate capability (92%). This asymmetric wire type supercapacitor demonstrates a low leakage current and self-discharge with a maximum volumetric energy (EV: 5.33 mW h cm-3) and power (PV: 855.69 mW cm-3) density.

  18. Martensitic Transformation in Ni-Mn-Sn-Co Heusler Alloys

    Directory of Open Access Journals (Sweden)

    Alexandre Deltell

    2015-04-01

    Full Text Available Thermal and structural austenite to martensite reversible transition was studied in melt spun ribbons of Ni50Mn40Sn5Co5, Ni50Mn37.5Sn7.5Co5 and Ni50Mn35Sn10Co5 (at. % alloys. Analysis of X-ray diffraction patterns confirms that all alloys have martensitic structure at room temperature: four layered orthorhombic 4O for Ni50Mn40Sn5Co5, four layered orthorhombic 4O and seven-layered monoclinic 14M for Ni50Mn37.5Sn7.5Co5 and seven-layered monoclinic 14M for Ni50Mn35Sn5Co5. Analysis of differential scanning calorimetry scans shows that higher enthalpy and entropy changes are obtained for alloy Ni50Mn37.5Sn7.5Co5, whereas transition temperatures increases as increasing valence electron density.

  19. Structural and magnetic properties of Ni-Zn and Ni-Zn-Co ferrites

    Energy Technology Data Exchange (ETDEWEB)

    Knyazev, A.V., E-mail: knyazevav@gmail.com [N.I. Lobachevsky State University of Nizhni Novgorod, Gagarin Prospekt 23/2, 603950 Nizhni Novgorod (Russian Federation); Zakharchuk, I.; Lähderanta, E. [Lappeenranta University of Technology, P.O. Box 20, FI-53851 Lappeenranta (Finland); Baidakov, K.V.; Knyazeva, S.S. [N.I. Lobachevsky State University of Nizhni Novgorod, Gagarin Prospekt 23/2, 603950 Nizhni Novgorod (Russian Federation); Ladenkov, I.V. [Joint-stock Company “Research and Production Company “Salut”, Nizhni Novgorod (Russian Federation)

    2017-08-01

    Highlights: • Ni-Zn and Ni-Zn-Co ferrite powders were prepared by the solid-state reaction at 1073 K. • The room temperature saturation magnetizations are 59.7 emu/g for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 57.1 emu/g for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. • The coercivity of the samples is found to be much larger than that of bulk ferrites and increases with Co introduction. • The temperature dependences of magnetization exhibit large spin frustration and spin-glass-like behavior. - Abstract: Ni-Zn and Ni-Zn-Co ferrite powders with nominal compositions Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4} were prepared by the solid-state reaction synthesis with periodic regrinding during the calcination at 1073 K. The structure of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4} was refined assuming space group F d-3m. Scanning electron microscopy revealed the average sizes of the crystalline ferrite particles are 130–630 nm for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 140–350 nm for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. The room temperature saturation magnetizations are 59.7 emu/g for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 57.1 emu/g for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. The coercivity of the samples is found to be much larger than that of bulk ferrites and increases with Co introduction. The Curie temperature tends to increase upon Zn substitution by Co, as well. The temperature dependences of magnetization measured using zero-field cooled and field cooled protocols exhibit large spin frustration and spin-glass-like behavior.

  20. Peculiarities of thermoelectric half-Heusler phase formation in Gd-Ni-Sb and Lu-Ni-Sb ternary systems

    Energy Technology Data Exchange (ETDEWEB)

    Romaka, V.V., E-mail: romakav@lp.edu.ua [Department of Applied Material Science and Materials Engineering, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Romaka, L.; Horyn, A. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya str. 6, 79005 Lviv (Ukraine); Rogl, P. [Institute of Materials Chemistry and Research, University of Vienna, Währingerstrasse 42, A-1090 Wien (Austria); Stadnyk, Yu; Melnychenko, N. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya str. 6, 79005 Lviv (Ukraine); Orlovskyy, M.; Krayovskyy, V. [Department of Applied Material Science and Materials Engineering, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine)

    2016-07-15

    The phase equilibria in the Gd–Ni–Sb and Lu-Ni-Sb ternary systems were studied at 873 K by X-ray and metallographic analyses in the whole concentration range. The interaction of the elements in the Gd–Ni–Sb system results the formation of five ternary compounds at investigated temperature: Gd{sub 5}Ni{sub 2}Sb (Mo{sub 5}SiB{sub 2}-type), Gd{sub 5}NiSb{sub 2} (Yb{sub 5}Sb{sub 3}-type), GdNiSb (MgAgAs-type), Gd{sub 3}Ni{sub 6}Sb{sub 5} (Y{sub 3}Ni{sub 6}Sb{sub 5}-type), and GdNi{sub 0.72}Sb{sub 2} (HfCuSi{sub 2}-type). At investigated temperature the Lu-Ni-Sb system is characterized by formation of the LuNiSb (MgAgAs-type), Lu{sub 5}Ni{sub 2}Sb (Mo{sub 5}SiB{sub 2}-type), and Lu{sub 5}Ni{sub 0.56}Sb{sub 2.44} (Yb{sub 5}Sb{sub 3}-type) compounds. The disordering in the crystal structure of half-Heusler GdNiSb and LuNiSb was revealed by EPMA and studied by means of Rietveld refinement and DFT modeling. The performed electronic structure calculations are in good agreement with electrical transport property studies. - Graphical abstract: Crystal structure model and electron localization function of Lu{sub 5}Ni{sub 2}Sb. Display Omitted - Highlights: • Gd-Ni-Sb and Lu-Ni-Sb phase diagrams were constructed at 873 K. • GdNiSb and LuNiSb are characterized by disordered crystal structure. • Crystal structure optimization with DFT calculations confirmed crystal structure disorder in GdNiSb and LuNiSb.