Motorcycle helmet use laws

Science.gov (United States)

2006-01-01

The National Highway Traffic Safety Administration (NHTSA) encourages States to enact legislation that requires all motorcycle riders to wear helmets. Motorcycle helmets provide the best protection from head injury for motorcyclists involved in traff...

The Ability of American Football Helmets to Manage Linear Acceleration With Repeated High-Energy Impacts.

Science.gov (United States)

Cournoyer, Janie; Post, Andrew; Rousseau, Philippe; Hoshizaki, Blaine

2016-03-01

Football players can receive up to 1400 head impacts per season, averaging 6.3 impacts per practice and 14.3 impacts per game. A decrease in the capacity of a helmet to manage linear acceleration with multiple impacts could increase the risk of traumatic brain injury. To investigate the ability of football helmets to manage linear acceleration with multiple high-energy impacts. Descriptive laboratory study. Laboratory. We collected linear-acceleration data for 100 impacts at 6 locations on 4 helmets of different models currently used in football. Impacts 11 to 20 were compared with impacts 91 to 100 for each of the 6 locations. Linear acceleration was greater after multiple impacts (91-100) than after the first few impacts (11-20) for the front, front-boss, rear, and top locations. However, these differences are not clinically relevant as they do not affect the risk for head injury. American football helmet performance deteriorated with multiple impacts, but this is unlikely to be a factor in head-injury causation during a game or over a season.

Towards reducing impact-induced brain injury: lessons from a computational study of army and football helmet pads.

Science.gov (United States)

Moss, William C; King, Michael J; Blackman, Eric G

2014-01-01

We use computational simulations to compare the impact response of different football and U.S. Army helmet pad materials. We conduct experiments to characterise the material response of different helmet pads. We simulate experimental helmet impact tests performed by the U.S. Army to validate our methods. We then simulate a cylindrical impactor striking different pads. The acceleration history of the impactor is used to calculate the head injury criterion for each pad. We conduct sensitivity studies exploring the effects of pad composition, geometry and material stiffness. We find that (1) the football pad materials do not outperform the currently used military pad material in militarily relevant impact scenarios; (2) optimal material properties for a pad depend on impact energy and (3) thicker pads perform better at all velocities. Although we considered only the isolated response of pad materials, not entire helmet systems, our analysis suggests that by using larger helmet shells with correspondingly thicker pads, impact-induced traumatic brain injury may be reduced.

The evaluation of speed skating helmet performance through peak linear and rotational accelerations.

Science.gov (United States)

Karton, Clara; Rousseau, Philippe; Vassilyadi, Michael; Hoshizaki, Thomas Blaine

2014-01-01

Like many sports involving high speeds and body contact, head injuries are a concern for short track speed skating athletes and coaches. While the mandatory use of helmets has managed to nearly eliminate catastrophic head injuries such as skull fractures and cerebral haemorrhages, they may not be as effective at reducing the risk of a concussion. The purpose of this study was to evaluate the performance characteristics of speed skating helmets with respect to managing peak linear and peak rotational acceleration, and to compare their performance against other types of helmets commonly worn within the speed skating sport. Commercially available speed skating, bicycle and ice hockey helmets were evaluated using a three-impact condition test protocol at an impact velocity of 4 m/s. Two speed skating helmet models yielded mean peak linear accelerations at a low-estimated probability range for sustaining a concussion for all three impact conditions. Conversely, the resulting mean peak rotational acceleration values were all found close to the high end of a probability range for sustaining a concussion. A similar tendency was observed for the bicycle and ice hockey helmets under the same impact conditions. Speed skating helmets may not be as effective at managing rotational acceleration and therefore may not successfully protect the user against risks associated with concussion injuries.

Application of Auxetic Foam in Sports Helmets

Directory of Open Access Journals (Sweden)

Leon Foster

2018-03-01

Full Text Available This investigation explored the viability of using open cell polyurethane auxetic foams to augment the conformable layer in a sports helmet and improve its linear impact acceleration attenuation. Foam types were compared by examining the impact severity on an instrumented anthropomorphic headform within a helmet consisting of three layers: a rigid shell, a stiff closed cell foam, and an open cell foam as a conformable layer. Auxetic and conventional foams were interchanged to act as the helmet’s conformable component. Attenuation of linear acceleration was examined by dropping the combined helmet and headform on the front and the side. The helmet with auxetic foam reduced peak linear accelerations (p < 0.05 relative to its conventional counterpart at the highest impact energy in both orientations. Gadd Severity Index reduced by 11% for frontal impacts (38.9 J and 44% for side impacts (24.3 J. The conformable layer within a helmet can influence the overall impact attenuating properties. The helmet fitted with auxetic foam can attenuate impact severity more than when fitted with conventional foam, and warrants further investigation for its potential to reduce the risk of traumatic brain injuries in sport specific impacts.

Examination of the protective roles of helmet/faceshield and directionality for human head under blast waves.

Science.gov (United States)

Sarvghad-Moghaddam, Hesam; Jazi, Mehdi Salimi; Rezaei, Asghar; Karami, Ghodrat; Ziejewski, Mariusz

2015-01-01

A parametric study was conducted to delineate the efficacy of personal protective equipment (PPE), such as ballistic faceshields and advanced combat helmets, in the case of a blast. The propagations of blast waves and their interactions with an unprotected head, a helmeted one, and a fully protected finite element head model (FEHM) were modeled. The biomechanical parameters of the brain were recorded when the FEHM was exposed to shockwaves from the front, back, top, and bottom. The directional dependent tissue response of the brain and the variable efficiency of PPE with respect to the blast orientation were two major results of this study.

The protective effect of helmet use in motorcycle and bicycle accidents: a propensity score-matched study based on a trauma registry system.

Science.gov (United States)

Kuo, Spencer C H; Kuo, Pao-Jen; Rau, Cheng-Shyuan; Chen, Yi-Chun; Hsieh, Hsiao-Yun; Hsieh, Ching-Hua

2017-08-07

Transportation by motorcycle and bicycle has become popular in Taiwan, this study was designed to investigate the protective effect of helmet use during motorcycle and bicycle accidents by using a propensity score-matched study based on trauma registry system data. Data of adult patients hospitalized for motorcycle or bicycle accidents between January 1, 2009 and December 31, 2015 were retrieved from the Trauma Registry System. These included 7735 motorcyclists with helmet use, 863 motorcyclists without helmet use, 76 bicyclists with helmet use, and 647 bicyclists without helmet use. The primary outcome measurement was in-hospital mortality. Secondary outcomes were the hospital length of stay (LOS), intensive care unit (ICU) admission rate, and ICU LOS. Normally distributed continuous data were analyzed by the unpaired Student t-test, and non-normally distributed data were compared using the Mann-Whitney U-test. Two-sided Fisher exact or Pearson chi-square tests were used to compare categorical data. Propensity score matching (1:1 ratio using optimal method with a 0.2 caliper width) was performed using NCSS software, adjusting for the following covariates: sex, age, and comorbidities. Further logistic regression was used to evaluate the effect of helmet use on mortality rates of motorcyclists and bicyclists, respectively. The mortality rate for motorcyclists with helmet use (1.1%) was significantly lower than for motorcyclists without helmet use (4.2%; odds ratio [OR] 0.2; 95% confidence interval [CI]: 0.17-0.37; p Motorcycle helmets provide protection to adult motorcyclists involved in traffic accidents and their use is associated with a decrease in mortality rates and the risk of head injuries. However, no such protective effect of helmet use was observed for bicyclists involved in collisions.

Children and cycle helmets -- the case against.

Science.gov (United States)

McCarthy, M

1996-03-01

Much of the literature on child cycling accidents appears to blame the child as a victim, as though children's activities of playing and travelling were somehow wrong and that children are at fault when an adult drives a car over them. This adult-centred approach then leads to the idea that children should protect themselves with helmets, and that they are to blame if they are injured. However, adults who continue to hold the fantasy that helmets might be of value should know that the British Standard for cycle helmets protects only in a vertical fall of 1 m -- certainly not motor vehicle crashes. Thicker motor cycle helmets would give better protection but, of course, are heavier (and therefore unsaleable). Yet even with compulsory wearing helmets, more motor cyclists still die of head injuries than pedal cyclists. In the Newcastle study, five times as many child pedestrians died of road accidents as child cyclists. Convinced helmeteers should recommend all children playing or travelling in the streets to wear helmets (presumably heavy motor-cycle helmets). Slightly more sceptical proponents might prefer half of them -- in a randomized controlled trial. Car driving appears to have as serious health consequences as tobacco, alcohol and drugs, and to be as addictive (McCarthy 1992). Helmets are similar to filters in cigarettes -- they give the illusion of safety to both consumer and producer of the product, but the illusion is fatal. Yet, for their cardiovascular and mental health, children should have the freedom to cycle in safety around where they live. A profound change in the habits of adults is needed, rather than suits of armour for children.

The impact of mandatory helmet law on the outcome of maxillo facial trauma: a comparative study in kerala.

Science.gov (United States)

Usha, M; Ravindran, V; Soumithran, C S; Ravindran Nair, K S

2014-06-01

Motorcyclists comprise the majority of road-traffic victims in low and middle income countries,and consequently, the majority of the road-traffic victims globally. Simple measures can be taken to make safer on the roads, which include enforcement of safety measures like seat belt and helmets. The compulsory Helmet law was enforced in Kerala on 18/06/07. Resistance to legislation on motorcycle helmets still coexists world wide with debate on the effectiveness of helmets. In an attempt to analyze the protective effect of helmets on facial injuries a comparative study was conducted in Government Dental College, Calicut, which is a major trauma centre in northern Kerala. Data for the present study was obtained from the patients who have reported to the Emergency Department of Oral and Maxillofacial Surgery, Government Dental College, Calicut, for a period of 6 months immediately after the implementation of strict helmet rule in Kerala. For the study all patients with a history of nonfatal motor cycle accident sustaining facial injuries were included. The results were compared with the study conducted in the same institution in the pre law period. The study demonstrates the protective effect of motorcycle helmets in decreasing the morbidity of maxillofacial trauma.There was a marked decrease in incidence of motorcycle-related injuries, remarkable increase in helmet usage and better outcome in helmeted individuals in the post law period. Road traffic injury control is a public health problem. Health and medical professionals have an ethical responsibility to educate and arrange for the safety of individuals. Helmets are effective in preventing or reducing the severity of motorcycle-related injuries and in a developing country like India, enforced mandatory motor cycle helmet law is potentially one of the most cost effective interventions available.

Bikes, helmets, and public health: decision-making when goods collide.

Science.gov (United States)

Bateman-House, Alison

2014-06-01

How ought public officials address policy choices that entail trade-offs between desirable public health goods? Increasing cycling improves public health both by promoting physical activity and by decreasing vehicle use, thus reducing vehicular emissions. Proponents of bicycle helmets argue that, used properly, they protect individual cyclists; however, there is concern that mandating helmet use may result in a decrease in cycling. In 2012, New York City Mayor Michael Bloomberg opposed a bicycle helmet mandate, concerned that it would have a negative impact on the city's cycling rate, which he had sought to increase. The mayor did not explain his rationale, leaving constituents unsure why he opposed the proposal. This case study underscores the challenge of creating public policy in the context of competing public health goods.

Impact response of US Army and National Football League helmet pad systems

Energy Technology Data Exchange (ETDEWEB)

Moss, W C; King, M J

2011-02-18

Lawrence Livermore National Laboratory [LLNL] was tasked to compare the impact response of NFL helmet pad systems and U.S. Army pad systems compatible with an Advanced Combat Helmet [ACH] at impact velocities up to 20 ft/s. This was a one-year study funded by the U.S. Army and JIEDDO. The Army/JIEDDO point of contact is COL R. Todd Dombroski, DO, JIEDDO Surgeon. LLNL was chosen by committee to perform the research based on prior published computational studies of the mechanical response of helmets and skulls to blast. Our collaborators include the U.S. Army Aeromedical Research Laboratory [USAARL] (a DoD laboratory responsible for impact testing helmets), Team Wendy and Oregon Aero (current and former ACH pad manufacturers), Riddell and Xenith (NFL pad manufacturers), and d3o (general purpose sports pad manufacturer). The manufacturer-supplied pad systems that were studied are shown in the figure below. The first two are the Army systems, which are bilayer foam pads with both hard and soft foam and a water-resistant airtight wrapper (Team Wendy) or a water-resistant airtight coating (Oregon Aero). The next two are NFL pad systems. The Xenith system consists of a thin foam pad and a hollow air-filled cylinder that elastically buckles under load. The Riddell system is a bilayer foam pad that is encased in an inflatable airbag with relief channels to neighboring pads in the helmet. The inflatable airbag is for comfort and provides no enhancement to impact mitigation. The d3o system consists of a rate-sensitive homogeneous dense foam. LLNL performed experiments to characterize the material properties of the individual foam materials and the response of the complete pad systems, to obtain parameters needed for the simulations. LLNL also performed X-ray CT scans of an ACH helmet shell that were used to construct a geometrically accurate computational model of the helmet. Two complementary sets of simulations were performed. The first set of simulations reproduced the

Helmet Use and Head Injury in Homer's Iliad.

Science.gov (United States)

Swinney, Christian

2016-06-01

Homer's detailed descriptions of head injuries inflicted during the Trojan War are of particular interest to individuals in the medical community. Although studies have examined the prevalence of such injuries, none have examined the preventive measures taken to avoid them. An in-depth review of helmet use in Homer's Iliad was conducted to address this previously unexplored facet of the epic. An English translation of Homer's text was reviewed for all references to helmet use. The number of helmet references in each book was recorded, along with other pertinent details for each reference. There were 87 references to helmets (40 combat, 47 noncombat). The helmet belonged to a Greek warrior in 41 cases (47.1%), a Trojan warrior in 38 cases (43.6%), a divinity in 5 cases (5.7%), and a general group of warriors in 3 cases (3.4%). Helmet use provided protective benefit to Greek warriors at a rate of 30.0% (3 of 10) and Trojan warriors at a rate of 11.1% (2 of 18). This difference was not statistically significant (P = 0.23). The overall combined protective benefit of helmet use in the text was 17.9% (5 of 28). Helmets belonging to 15 specific Greek warriors and 18 specific Trojan warriors were referenced in the text. Helmets belonging to Hector (n = 12) and Achilles (n = 8) were most frequently mentioned. Helmet use and head injury both play a prominent role in Homer's Iliad. Helmets are frequently used in combat settings but with relatively little success. Helmets are also used in various noncombat settings. Copyright © 2016 Elsevier Inc. All rights reserved.

How Satisfied are Soldiers with their Ballistic Helmets? A Comparison of Soldiers' Opinions about the Advanced Combat Helmet and the Personal Armor System for Ground Troops

National Research Council Canada - National Science Library

Ivins, Brian J; Schwab, Karen; Crowley, John S; McEntire, B. J; Trumble, Christopher C; Brown, Fred H; Warden, Deborah L

2008-01-01

.... These factors affect Soldiers' decisions about helmet use; therefore, rigorous research about Soldiers' real-life experiences with helmets is critical to assessing a helmet's overall protective efficacy...

29 CFR 1926.100 - Head protection.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Head protection. 1926.100 Section 1926.100 Labor... § 1926.100 Head protection. (a) Employees working in areas where there is a possible danger of head... protected by protective helmets. (b) Helmets for the protection of employees against impact and penetration...

Observation of motorcycle helmet use rates in Michigan after partial repeal of the universal motorcycle helmet law.

Science.gov (United States)

Buckley, Lisa; Bingham, C Raymond; Flannagan, Carol A; Carter, Patrick M; Almani, Farideh; Cicchino, Jessica B

2016-10-01

Motorcycle crashes result in a significant health burden, including many fatal injuries and serious non-fatal head injuries. Helmets are highly effective in preventing such trauma, and jurisdictions that require helmet use of all motorcyclists have higher rates of helmet use and lower rates of head injuries among motorcyclists. The current study examines helmet use and characteristics of helmeted operators and their riding conditions in Michigan, following a weakening of the state's universal motorcycle helmet use law in April 2012. Data on police-reported crashes occurring during 2012-14 and from a stratified roadside observational survey undertaken in Southeast Michigan during May-September 2014 were used to estimate statewide helmet use rates. Observed helmet use was more common among operators of sports motorcycles, on freeways, and in the morning, and least common among operators of cruisers, on minor arterials, and in the afternoon. The rate of helmet use across the state was estimated at 75%, adjusted for roadway type, motorcycle class, and time of day. Similarly, the helmet use rate found from examination of crash records was 73%. In the observation survey, 47% of operators wore jackets, 94% wore long pants, 54% wore boots, and 80% wore gloves. Protective clothing of jackets and gloves was most often worn by sport motorcycle operators and long pants and boots most often by riders of touring motorcycles. Findings highlight the much lower rate of helmet use in Michigan compared with states that have a universal helmet use law, although the rate is higher than observed in many states with partial helmet laws. Targeted interventions aimed at specific groups of motorcyclists and situations where helmet use rates are particularly low should be considered to increase helmet use. Copyright © 2016 Elsevier Ltd. All rights reserved.

The mystery of the missing Viking helmets.

Science.gov (United States)

Wester, K

2000-11-01

Based on archaeological finds and old Norse literature, this study describes the Scandinavian helmet tradition from the Bronze Age to the Viking Age, as well as the Viking culture, with special emphasis on weaponry and head protection. Contrary to what is commonly believed, the study shows that metal helmets must have been used very infrequently by the Vikings. In fact, only one Viking helmet has been retrieved in Scandinavia. Possible reasons for the widespread misconception that the Vikings wore helmets are discussed, and the responsibility for not correcting this misunderstanding is placed with the archaeological profession.

Investigation on the applicability of dust protection helmets in the mining industry. Untersuchungen ueber die Einsatzmoeglichkeiten von Staubschutzhelmen im Bergbau

Energy Technology Data Exchange (ETDEWEB)

Bauer, H.D.; Werner, W.; Fuerst, E.

1984-10-01

In case of static ambient air, leakages for volumes of 25 x 1,5 l/min and air supplies >= 120 l/min or 25 x 2,0 l/min and >= 160 l/min do not occur. The increasing flow rate of moving ambient air leads to an increase of leakages. They show their largest extensions in case of lateral flow. In addition, they expand together with increasing physiological load. Therefore, the inherent air supply should not be below 160 l/min. The comparison of the dust protection helmet 'Airstream AH 1' with two respirators revealed the lowest additional physiological load for the dust protection helmet. Applicability tests in situ resulted in the following principal objections: contamination and scratches on the visor leading to visibility restriction of the wearer, bad fit, weight distribution and helmet dimensions, pressure sores and chafes of sealing parts and edges, lamp installation. Air supply and movement were felt as too high in case of low ambient temperatures, and in case of high temperatures and physiological strain it was considered as too low. There were only few objections against fan noise, weight and impediment by cable and battery. Based on the results, a specification including monitoring and maintenance of the helmet was made and additional tests for DIN design 58 645, item 7, were induced. Furthermore, a proposal regarding helmet optimisation was made.

Helmet Sensor - Transfer Function and Model Development

Science.gov (United States)

2010-09-01

that helmets be examined forensically when estimating the impact direction and location and the electronic HMSS data not be used in that determination... forensic analysis of the helmet itself is therefore recommended to determine the direction and severity of the ballistic impact 5. The helmet shell does...ot83 HTI l ot 8J HT1 lot S ,HTt IOt S , HTI l otiH HTt lotSS HTt l vt85 HTI l o)t 85 HT1 Front Level Acceleration ~~,--~----~--,30’p~g

The Economic Impact of Helmet Use on Motorcycle Accidents: A Systematic Review and Meta-analysis of the Literature from the Past 20 Years.

Science.gov (United States)

Kim, Chang-Yeon; Wiznia, Daniel H; Averbukh, Leon; Dai, Feng; Leslie, Michael P

2015-01-01

The incidence and cost of motorcycle accidents are projected to increase. Motorcycle helmets are accepted as an effective strategy for reducing the morbidity and therefore the cost of motorcycle accidents. Despite this, states have continued to repeal helmet laws in the past 20 years. In addition, variations in the methodologies and outcomes of published reports have contributed to uncertainty regarding the health care dollars saved due to motorcycle helmet use. The purpose of this systematic review and meta-analysis is to clarify the economic impact of motorcycle helmet use. Our primary source was Medline. Search terms included "motorcycle," "motorbike," "motorcycle helmet," "head protective devices," and "cost and cost analysis." The review only included articles that were primary studies, written in English, evaluations of periods after 1994, and published in a peer-reviewed journal. Two independent authors extracted data using predefined data fields. Meta-analysis was done using the R-metafor package. Twelve papers met the criteria for inclusion. Meta-analysis demonstrated that nonhelmeted patients required $12,239 more in hospital costs per patient. Nonhelmeted patients also required more postdischarge care and were more likely to use publicly funded insurance. Studies also found lower injury severity and better hospital course in the helmeted population. Study limitations included selection bias, unclear statistical assumptions, lack of precision measures, confounding variables, and lack of standardization to a common year. Meta-analysis demonstrated an I2 of 67%, attributing a significant proportion of outcome variation to study differences. Motorcycle helmet use reduces morbidity and contributes to significant health care cost savings. Continuing antihelmet legislation will impose a substantial economic burden to the health care system, the government, and the public.

Effects of repealing the motorcycle helmet law in Michigan.

Science.gov (United States)

Hothem, Zachary; Simon, Robert; Barnes, Wesley; Mohammad, Azmath; Sevak, Shruti; Ziegler, Kathryn; Iacco, Anthony; Janczyk, Randy

2017-09-01

In 2012, Michigan repealed its universal helmet law. Our study assessed the clinical impact of this repeal. Our trauma database was queried retrospectively for 2 motorcycle riding seasons before and 3 seasons after repeal. On-scene death data was obtained from the Medical Examiner. Helmet use in hospitalized patients decreased after the helmet law repeal. Non-helmeted patients had a significant increased rate of head injury. Non-helmeted patients were more likely to die during hospitalization. While, helmet use and drugs/alcohol status significantly affected the risk for head injury, only drug/alcohol had a significant effect on overall mortality. Following helmet law repeal, helmet use has decreased. Helmet status and drug/alcohol use was found to significantly increase risk of head injury. Although overall mortality was only affected by drug/alcohol use, non-helmeted patients did have a higher inpatient mortality. These findings deserve furthermore study and may provide a basis for reinstating the universal helmet law. Copyright © 2016 Elsevier Inc. All rights reserved.

Novel Method of Weighting Cumulative Helmet Impacts Improves Correlation with Brain White Matter Changes After One Football Season of Sub-concussive Head Blows.

Science.gov (United States)

Merchant-Borna, Kian; Asselin, Patrick; Narayan, Darren; Abar, Beau; Jones, Courtney M C; Bazarian, Jeffrey J

2016-12-01

One football season of sub-concussive head blows has been shown to be associated with subclinical white matter (WM) changes on diffusion tensor imaging (DTI). Prior research analyses of helmet-based impact metrics using mean and peak linear and rotational acceleration showed relatively weak correlations to these WM changes; however, these analyses failed to account for the emerging concept that neuronal vulnerability to successive hits is inversely related to the time between hits (TBH). To develop a novel method for quantifying the cumulative effects of sub-concussive head blows during a single season of collegiate football by weighting helmet-based impact measures for time between helmet impacts. We further aim to compare correlations to changes in DTI after one season of collegiate football using weighted cumulative helmet-based impact measures to correlations using non-weighted cumulative helmet-based impact measures and non-cumulative measures. We performed a secondary analysis of DTI and helmet impact data collected on ten Division III collegiate football players during the 2011 season. All subjects underwent diffusion MR imaging before the start of the football season and within 1 week of the end of the football season. Helmet impacts were recorded at each practice and game using helmet-mounted accelerometers, which computed five helmet-based impact measures for each hit: linear acceleration (LA), rotational acceleration (RA), Gadd Severity Index (GSI), Head Injury Criterion (HIC 15 ), and Head Impact Technology severity profile (HITsp). All helmet-based impact measures were analyzed using five methods of summary: peak and mean (non-cumulative measures), season sum-totals (cumulative unweighted measures), and season sum-totals weighted for time between hits (TBH), the interval of time from hit to post-season DTI assessment (TUA), and both TBH and TUA combined. Summarized helmet-based impact measures were correlated to statistically significant changes in

Capabilities of Helmets for Preventing Head Injuries Induced by Ballistic Impacts

Directory of Open Access Journals (Sweden)

D.V. Balandin

2004-01-01

Full Text Available The limiting performance of ballistically loaded helmets designed to reduce head injuries is studied analytically. The projectile does not penetrate the helmet. This analysis evaluates the absolute minimum of the peak displacement of the helmet shell relative to the head, provided that criteria measuring the severity of head injuries lie within prescribed limits. Rather than optimize a specific design configuration, e.g. a viscoelastic foam liner, characteristics of a time-dependent force representing the helmet liner are calculated. The formulation reduces the limiting performance analysis to an optimal control problem.

Viet Nam’s mandatory motorcycle helmet law and its impact on children

Science.gov (United States)

Pervin, Aaron; Sidik, Mirjam; McKinley, Tyler; Tu, Nguyen Thi Hong; Nam, Nguyen Phuong

2009-01-01

Abstract Objective To measure the use of motorcycle helmets in children and to determine the reasons why children wear helmets less often than adults. Methods The frequency of helmet wearing among adults and children was ascertained by trained roadside observers, and randomized road user surveys were completed in four major centres in Viet Nam: Hanoi, Ho Chi Minh City, Can Tho and Da Nang. Survey data on key questions were cross tabulated, and χ² was calculated for significant differences between parents and non-parents (0.05). Findings The frequency of helmet use in the four study locations ranged from 90–99% among adults, from 15–53% among children ≤ 7 years of age, and from 38–53% among children > 7 but ≤ 14. Of the parents surveyed, 67% said the fear of neck injury was the most important reason their children did not wear a helmet. Conclusion Children wear motorcycle helmets much less often than adults. Legislation to penalize adults whose children do not wear motorcycle helmets has been proposed in Viet Nam. Furthermore, ongoing advocacy and social marketing efforts are being made to disseminate information about the safety benefits of helmets to combat erroneous public perceptions. PMID:19551255

Brain response to primary blast wave using validated finite element models of human head and advanced combat helmet

Directory of Open Access Journals (Sweden)

Liying eZhang

2013-08-01

Full Text Available Blast-induced traumatic brain injury has emerged as a signature injury in combat casualty care. Present combat helmets are designed primarily to protect against ballistic and blunt impacts, but the current issue with helmets is protection concerning blasts. In order to delineate the blast wave attenuating capability of the Advanced Combat Helmet (ACH, a finite element (FE study was undertaken to evaluate the head response against blast loadings with and without helmet using a partially validated FE model of the human head and ACH. Four levels of overpressures (0.27-0.66 MPa from the Bowen’s lung iso-damage threshold curves were used to simulate blast insults. Effectiveness of the helmet with respect to head orientation was also investigated. The resulting biomechanical responses of the brain to blast threats were compared for human head with and without the helmet. For all Bowen’s cases, the peak intracranial pressures (ICP in the head ranged from 0.68-1.8 MPa in the coup cortical region. ACH was found to mitigate ICP in the head by 10-35%. Helmeted head resulted in 30% lower average peak brain strains and product of strain and strain rate. Among three blast loading directions with ACH, highest reduction in peak ICP (44% was due to backward blasts whereas the lowest reduction in peak ICP and brain strains was due to forward blast (27%. The biomechanical responses of a human head to primary blast insult exhibited directional sensitivity owing to the different geometry contours and coverage of the helmet construction and asymmetric anatomy of the head. Thus, direction-specific tolerances are needed in helmet design in order to offer omni-directional protection for the human head. The blasts of varying peak overpressures and durations that are believed to produce the same level of lung injury produce different levels of mechanical responses in the brain, and hence "iso-damage" curves for brain injury are likely different than the Bowen curves

The Effects of the Personal Armor System for Ground Troops (PASGT) and the Advanced Combat Helmet (ACH) with and without PVS-14 Night Vision Goggles (NVG) on Neck Biomechanics During Dismounted Soldier Movements

National Research Council Canada - National Science Library

LaFiandra, Michael; Harman, Everett; Cornelius, Nancy; Frykman, Peter; Gutekunst, David; Nelson, Gabe

2007-01-01

Kevlar helmets provide the soldier with basic ballistic and impact protection. However, the helmet has recently become a mounting platform for devices such as night-vision goggles, drop down displays, weapon-aiming systems, etc...

Characteristics of helmet or knit cap use in head injury of snowboarders.

Science.gov (United States)

Fukuda, Osamu; Hirashima, Yutaka; Origasa, Hideki; Endo, Shunro

2007-11-01

The rate of head injury is 1.86-6 times higher for snowboarding than for skiing. Detailed data about the usefulness of a helmet or knit cap for protecting against serious head injuries have not been reported. The present study evaluated the use of a helmet or knit cap for preventing head injuries. Questionnaire data were collected from 1,190 consecutive patients in a hospital during the 1999/2000-2002/2003 winter seasons at Uonuma ski resort, Niigata, Japan. Patients were divided into the helmet, knit cap, and no cap groups. Upper technical level was highest and jumping as the cause of injury was most frequent in the helmet group. After adjustment for other confounders, there was a significant negative association between the occurrence of serious head injury during snowboarding and female sex (adjusted odds ratio 0.55, 95% confidence interval 0.421-0.718, p jumping (adjusted odds ratio 2.25, 95% confidence interval 1.48-3.43, p = 0.0001). Among snowboarding maneuvers, only jumping showed a significant negative association between wearing of a helmet or knit cap and the occurrence of serious head injury (p = 0.036). Snowboarders who wear helmets might attempt dangerous maneuvers causing injuries. Wearing of a helmet or knit cap protected against serious head injuries on jumping. Every snowboarder should wear a helmet or knit cap on jumping to prevent head injury.

Paternalism & Its Discontents: Motorcycle Helmet Laws, Libertarian Values, and Public Health

Science.gov (United States)

Jones, Marian Moser; Bayer, Ronald

2007-01-01

The history of motorcycle helmet legislation in the United States reflects the extent to which concerns about individual liberties have shaped the public health debate. Despite overwhelming epidemiological evidence that motorcycle helmet laws reduce fatalities and serious injuries, only 20 states currently require all riders to wear helmets. During the past 3 decades, federal government efforts to push states toward enactment of universal helmet laws have faltered, and motorcyclists’ advocacy groups have been successful at repealing state helmet laws. This history raises questions about the possibilities for articulating an ethics of public health that would call upon government to protect citizens from their own choices that result in needless morbidity and suffering. PMID:17194856

High School Football Players Use Their Helmets to Tackle Other Players Despite Knowing the Risks.

Science.gov (United States)

Kuriyama, Andrew M; Nakatsuka, Austin S; Yamamoto, Loren G

2017-03-01

There is greater attention to head-related injuries and concussions in American football. The helmet's structural safety and the way that football players use their helmets are important in preventing head injuries. Current strategies include penalizing players for high-risk behavior such as leading with their helmet or hitting an opposing player above the shoulder. Passive strategies include helmet modification to better protect the head of the players or to change the playing style of the players. Hawai'i high school varsity football players were surveyed to determine how they use their helmets and how a new helmet design would affect their style of play. One hundred seventy-seven surveys were completed; 79% said that they used their helmet to hit an opposing player during a tackle and 46% said they made this contact intentionally. When asked about modifying helmets with a soft material on the outside, 48% said they thought putting a soft cover over a regular helmet would protect their head better. However, many participants said that putting a soft cover over their regular helmet was a bad idea for various reasons. Most young football players use their helmets to block or tackle despite being taught they would be penalized or potentially injured if they did so. By gaining a better understanding of why and how players use their helmets and how they would respond to new helmet designs, steps can be taken to reduce head injuries for all levels of play.

Impact of Helmet Use on Injury and Financial Burden of Motorcycle and Moped Crashes in Hawai‘i: Analysis of a Linked Statewide Database

Science.gov (United States)

Castel, Nikki A; Wong, Linda L; Steinemann, Susan

2016-01-01

Helmet use reduces injury severity, disability, hospital length of stay, and hospital charges in motorcycle riders. The public absorbs billions of dollars annually in hospital charges for unhelmeted, uninsured motorcycle riders. We sought to quantify, on a statewide level, the healthcare burden of unhelmeted motorcycle and moped riders. We examined 1,965 emergency medical service (EMS) reports from motorcycle and moped crashes in Hawai‘i between 2007–2009. EMS records were linked to hospital medical records to assess associations between vehicle type, helmet use, medical charges, diagnoses, and final disposition. Unhelmeted riders of either type of vehicle suffered more head injuries, especially skull fractures (adjusted odds ratio (OR) of 4.48, P motorcycle and moped riders, with a significant (P = .006) difference between helmeted ($27,176) and unhelmeted ($40,217) motorcycle riders. Unhelmeted riders were twice as likely to self-pay (19.3%, versus 9.8% of helmeted riders), and more likely to have Medicaid or a similar income-qualifying insurance plan (13.5% versus 5.0%, respectively). Protective associations with helmet use are stronger among motorcyclists than moped riders, suggesting the protective effect is augmented in higher speed crashes. The public financial burden is higher from unhelmeted riders who sustain more severe injuries and are less likely to be insured. PMID:27980882

Dynamic Response and Residual Helmet Liner Crush Using Cadaver Heads and Standard Headforms.

Science.gov (United States)

Bonin, S J; Luck, J F; Bass, C R; Gardiner, J C; Onar-Thomas, A; Asfour, S S; Siegmund, G P

2017-03-01

Biomechanical headforms are used for helmet certification testing and reconstructing helmeted head impacts; however, their biofidelity and direct applicability to human head and helmet responses remain unclear. Dynamic responses of cadaver heads and three headforms and residual foam liner deformations were compared during motorcycle helmet impacts. Instrumented, helmeted heads/headforms were dropped onto the forehead region against an instrumented flat anvil at 75, 150, and 195 J. Helmets were CT scanned to quantify maximum liner crush depth and crush volume. General linear models were used to quantify the effect of head type and impact energy on linear acceleration, head injury criterion (HIC), force, maximum liner crush depth, and liner crush volume and regression models were used to quantify the relationship between acceleration and both maximum crush depth and crush volume. The cadaver heads generated larger peak accelerations than all three headforms, larger HICs than the International Organization for Standardization (ISO), larger forces than the Hybrid III and ISO, larger maximum crush depth than the ISO, and larger crush volumes than the DOT. These significant differences between the cadaver heads and headforms need to be accounted for when attempting to estimate an impact exposure using a helmet's residual crush depth or volume.

Correlates and Barriers Associated with Motorcycle Helmet Use in Wa, Ghana.

Science.gov (United States)

Akaateba, Millicent Awialie; Yakubu, Ibrahim; Akanbang, Bernard Afiik Akanpabadai

2015-01-01

This study was conducted to investigate the correlates and barriers to helmet use among motorcycle riders in Wa, a motorcycle-predominant town in Ghana. An additional objective was to determine the association between helmet use and riders' knowledge, attitudes, and beliefs toward helmets. Cross-sectional surveys including both observation of helmet use and interviews were conducted among motorcycle riders at 6 randomly selected fuel stations and 4 motorcycle service centers within and outside the Central Business District of Wa. Questions covered riders' sociodemographic and riding characteristics, helmet use, reasons for use or nonuse of helmets, and knowledge, attitudes, and beliefs about helmets. Analyses were based on frequencies and testing of strength of association using adjusted odds ratios (with 95% confidence intervals) in binary logistic regression. The prevalence of helmet use among the 271 sampled riders was 46% (95% confidence interval [CI], 40.2-52.0). Gender, age, marital status, and occupation were significant sociodemographic correlates of helmet use in Wa. Compared to currently married riders, unmarried riders were 5 times less likely to use a helmet. No significant association existed between riders' educational attainment and helmet use. Helmet use was also positively correlated with helmet ownership and license holding. The leading reasons stated for helmet nonuse among nonusers were not traveling a long distance and helmets block vision and hearing. Protection from injury, legal requirement, and coping with the police for fear of being accosted for helmet nonuse were identified as common reasons for helmet use. Positive attitudes and beliefs were also significantly correlated with helmet use. Despite the existence of a legislation mandating the use of helmets on all roads as well as the high level of awareness among riders on this legislation and the benefits of helmets, the incidence of helmet use among motorists continue to be low in Wa

Paternalism and its discontents: motorcycle helmet laws, libertarian values, and public health.

Science.gov (United States)

Jones, Marian Moser; Bayer, Ronald

2007-02-01

The history of motorcycle helmet legislation in the United States reflects the extent to which concerns about individual liberties have shaped the public health debate. Despite overwhelming epidemiological evidence that motorcycle helmet laws reduce fatalities and serious injuries, only 20 states currently require all riders to wear helmets. During the past 3 decades, federal government efforts to push states toward enactment of universal helmet laws have faltered, and motorcyclists' advocacy groups have been successful at repealing state helmet laws. This history raises questions about the possibilities for articulating an ethics of public health that would call upon government to protect citizens from their own choices that result in needless morbidity and suffering.

The effects of motorcycle helmets on hearing and the detection of warning signals

Science.gov (United States)

Van Moorhem, W. K.; Shepherd, K. P.; Magleby, T. D.; Torian, G. E.

1981-07-01

Measurements of the at-ear helmet-generated aerodynamic noise and helmet insertion loss were carried out for the two major types of motorcycle helmets. From these data and existing information on noise generation by flow around a bare head it was found that for quiet motorcycles at typical operating speeds a significant part of the riders at-ear noise is generated by the air flow. An assessment of the possibility of hearing damage was then carried out. It was found that only with extremely high usage would there be a significant risk of hearing damage for either the bare headed or helmeted rider. Helmets did, however, give significant protection. Detection of warning signals was then considered. It was found that under none of the conditions investigated here did the helmet put its wearer at a disadvantage compared with the bare headed rider, and at typical constant speeds the helmet gave a rider an advantage in the detection of warning signals.

Methodologies for Blunt Trauma Assessment in Military Helmets

Science.gov (United States)

2010-09-13

Assessment; Monorail Drop Tower 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER OF PAGES 10 19a. NAME OF RESPONSIBLE...Laboratory Test Procedure for Motorcycle Helmets (TP-218-06) [8]. TP-218-06 specifies a guided monorail drop and provides requirements for how helmets...a hemispherical anvil. The monorail restricts movement to control the impact location, and acceleration is measured using a uniaxial accelerometer

Ballistic Characterization Of A Typical Military Steel Helmet

Directory of Open Access Journals (Sweden)

Mohamed Ali Maher

2017-08-01

Full Text Available In this study the ballistic limit of a steel helmet against a FMJ 919 mm caliber bullet is estimated. The helmet model is the typical polish helmet wz.31.The helmet material showed high strength low alloy steel material of 0.28 carbon content and 9.125 kgm2 areal density. The tensile test according to ASTM E8 showed a tensile strength of 1236.4 MPa .The average hardness value was about HV550. First shooting experiment has been executed using a 9 mm pistol based on 350 ms muzzle velocity at 5m against the simply supported helmet complete penetrations rose in this test were in the form of cracks on the helmet surface and partial penetrations were in the form of craters on the surface whose largest diameter and depth were 43 mm and 20.2 mm consequently .The second experiment was on a rifled gun arrangement 13 bullets of 919 mm caliber were shot on the examined simply supported steel helmet at a zero obliquity angle at different velocities to determine the ballistic limit velocity V50 according to MIL-STD-662F. Three major outcomes were revealed 1 the value V50 which found to be about 390 ms is higher than the one found in literature 360 ms German steel helmet model 1A1. 2 The smallest the standard deviation of the mixed results zone data the most accurate the ballistic limit is. 3Similar to the performance of blunt-ended projectiles impacting overmatching targets tD near 11 or larger It was found that the dominating failure mode of the steel helmet stuck by a hemispherical-nose projectile was plugging mode despite of having tD ratio of about 19 undermatching.

In defence of mandatory bicycle helmet legislation: response to Hooper and Spicer.

Science.gov (United States)

Biegler, Paul; Johnson, Marilyn

2015-08-01

We invoke a triple rationale to rebut Hooper and Spicer's argument against mandatory helmet laws. First, we use the laws of physics and empirical studies to show how bicycle helmets afford substantial protection to the user. We show that Hooper and Spicer erroneously downplay helmet utility and that, as a result, their attack on the utilitarian argument for mandatory helmet laws is weakened. Next, we refute their claim that helmet legislation comprises unjustified paternalism. We show the healthcare costs of bareheaded riding to pose significant third party harms. It follows, we argue, that a utilitarian case for helmet laws can be sustained by appeal to Mill's Harm Principle. Finally, we reject Hooper and Spicer's claim that helmet laws unjustly penalise cyclists for their own health-affecting behaviour. Rather, we show their argument to suffer by disanalogy with medical cases where injustice may be more evident, for example, denial of bypass surgery to smokers. We conclude that mandatory helmet laws offer substantial utility and are entirely defensible within the framework of a liberal democracy. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The Effects of Motorcycle Helmet Legislation on Craniomaxillofacial Injuries.

Science.gov (United States)

Adams, Nicholas S; Newbury, Patrick A; Eichhorn, Mitchell G; Davis, Alan T; Mann, Robert J; Polley, John W; Girotto, John A

2017-06-01

Motorcycle helmet legislation has been a contentious topic for over a half-century. Benefits of helmet use in motorcycle trauma patients are well documented. In 2012, Michigan repealed its universal motorcycle helmet law in favor of a partial helmet law. The authors describe the early clinical effects on facial injuries throughout Michigan. Retrospective data from the Michigan Trauma Quality Improvement Program trauma database were evaluated. Included were 4643 motorcycle trauma patients presenting to 29 Level I and II trauma centers throughout Michigan 3 years before and after the law repeal (2009 to 2014). Demographics, external cause of injury codes, International Classification of Diseases, Ninth Revision diagnosis codes, and injury details were gathered. The proportion of unhelmeted trauma patients increased from 20 percent to 44 percent. Compared with helmeted trauma patients, unhelmeted patients were nearly twice as likely to sustain craniomaxillofacial injuries (relative risk, 1.90), including fractures (relative risk, 2.02) and soft-tissue injuries (relative risk, 1.94). Unhelmeted patients had a lower Glasgow Coma Scale score and higher Injury Severity Scores. Patients presenting after helmet law repeal were more likely to sustain craniomaxillofacial injuries (relative risk, 1.46), including fractures (relative risk, 1.28) and soft-tissue injuries (relative risk, 1.56). No significant differences were observed for age, sex, Injury Severity Score, or Glasgow Coma Scale score (p > 0.05). This study highlights the significant negative impact of relaxed motorcycle helmet laws leading to an increase in craniomaxillofacial injuries. The authors urge state and national legislators to reestablish universal motorcycle helmet laws.

Laminated helmet materials characterization by terahertz kinetics spectroscopy

Science.gov (United States)

Rahman, Anis; Rahman, Aunik K.

2015-05-01

High speed acquisition of reflected terahertz energy constitutes a kinetics spectrum that is an effective tool for layered materials' deformation characterization under ballistic impact. Here we describe utilizing the kinetics spectrum for quantifying a deformation event due to impact in material used for Soldier's helmet. The same technique may be utilized for real-time assessment of trauma by measuring the helmet wore by athletes. The deformation of a laminated material (e.g., a helmet) is dependent on the nature of impact and projectile; thus can uniquely characterize the impact condition leading to a diagnostic procedure based on the energy received by an athlete during an impact. We outline the calibration process for a given material under ballistic impact and then utilize the calibration for extracting physical parameters from the measured kinetics spectrum. Measured kinetics spectra are used to outline the method and rationale for extending the concept to a diagnosis tool. In particular, captured kinetics spectra from multilayered plates subjected to ballistic hit under experimental conditions by high speed digital acquisition system. An algorithm was devised to extract deformation and deformation velocity from which the energy received on the skull was estimated via laws of nonrelativistic motion. This energy is assumed to be related to actual injury conditions, thus forming a basis for determining whether the hit would cause concussion, trauma, or stigma. Such quantification may be used for diagnosing a Soldier's trauma condition in the field or that of an athlete's.

Additional helmet and pack loading reduce situational awareness during the establishment of marksmanship posture.

Science.gov (United States)

Lim, Jongil; Palmer, Christopher J; Busa, Michael A; Amado, Avelino; Rosado, Luis D; Ducharme, Scott W; Simon, Darnell; Van Emmerik, Richard E A

2017-06-01

The pickup of visual information is critical for controlling movement and maintaining situational awareness in dangerous situations. Altered coordination while wearing protective equipment may impact the likelihood of injury or death. This investigation examined the consequences of load magnitude and distribution on situational awareness, segmental coordination and head gaze in several protective equipment ensembles. Twelve soldiers stepped down onto force plates and were instructed to quickly and accurately identify visual information while establishing marksmanship posture in protective equipment. Time to discriminate visual information was extended when additional pack and helmet loads were added, with the small increase in helmet load having the largest effect. Greater head-leading and in-phase trunk-head coordination were found with lighter pack loads, while trunk-leading coordination increased and head gaze dynamics were more disrupted in heavier pack loads. Additional armour load in the vest had no consequences for Time to discriminate, coordination or head dynamics. This suggests that the addition of head borne load be carefully considered when integrating new technology and that up-armouring does not necessarily have negative consequences for marksmanship performance. Practitioner Summary: Understanding the trade-space between protection and reductions in task performance continue to challenge those developing personal protective equipment. These methods provide an approach that can help optimise equipment design and loading techniques by quantifying changes in task performance and the emergent coordination dynamics that underlie that performance.

Evaluation of possible head injuries ensuing a cricket ball impact.

Science.gov (United States)

Mohotti, Damith; Fernando, P L N; Zaghloul, Amir

2018-05-01

The aim of this research is to study the behaviour of a human head during the event of an impact of a cricket ball. While many recent incidents were reported in relation to head injuries caused by the impact of cricket balls, there is no clear information available in the published literature about the possible threat levels and the protection level of the current protective equipment. This research investigates the effects of an impact of a cricket ball on a human head and the level of protection offered by the existing standard cricket helmet. An experimental program was carried out to measure the localised pressure caused by the impact of standard cricket balls. The balls were directed at a speed of 110 km/h on a 3D printed head model, with and without a standard cricket helmet. Numerical simulations were carried out using advanced finite element package LS-DYNA to validate the experimental results. The experimental and numerical results showed approximately a 60% reduction in the pressure on the head model when the helmet was used. Both frontal and side impact resulted in head acceleration values in the range of 225-250 g at a ball speed of 110 km/h. There was a 36% reduction observed in the peak acceleration of the brain when wearing a helmet. Furthermore, numerical simulations showed a 67% reduction in the force on the skull and a 95% reduction in the skull internal energy when introducing the helmet. (1) Upon impact, high localised pressure could cause concussion for a player without helmet. (2) When a helmet was used, the acceleration of the brain observed in the numerical results was at non-critical levels according to existing standards. (3) A significant increase in the threat levels was observed for a player without helmet, based on force, pressure, acceleration and energy criteria, which resulted in recommending the compulsory use of the cricket helmet. (4) Numerical results showed a good correlation with experimental results and hence, the

Inadequate Helmet Fit Increases Concussion Severity in American High School Football Players.

Science.gov (United States)

Greenhill, Dustin A; Navo, Paul; Zhao, Huaqing; Torg, Joseph; Comstock, R Dawn; Boden, Barry P

2016-05-01

There is limited information on the relationship between football helmet fit and concussion severity. Poor helmet fit may predispose football players to a more severe concussion. Descriptive epidemiology study. Level 3. Data from concussion injury reports were obtained from the National High School Sports-Related Injury Surveillance System over a 9-year period. Symptoms, duration, and helmet parameters (fit, interior padding) were analyzed for all first-time concussions. Data from 4580 concussions were analyzed. Patients who suffered concussions with a helmet that did not fit properly (3.22%), as determined by an athletic trainer, had higher rates of drowsiness (RR, 1.46; P = 0.005), hyperexcitability (RR, 2.38; P = 0.047), and sensitivity to noise (RR, 1.88; P football helmet is a risk factor for a concussion with more symptoms and of longer duration. Concussions of longer duration are also more common in players with an air bladder-lined helmet. Current high school football rules should mandate supervision and maintenance of helmet fit throughout the season, prior to impact. Team physicians, athletic trainers, coaches, and high school officials should ensure proper oversight of helmet fit in high school athletes to decrease concussion severity and duration. © 2016 The Author(s).

Noise-Canceling Helmet Audio System

Science.gov (United States)

Seibert, Marc A.; Culotta, Anthony J.

2007-01-01

A prototype helmet audio system has been developed to improve voice communication for the wearer in a noisy environment. The system was originally intended to be used in a space suit, wherein noise generated by airflow of the spacesuit life-support system can make it difficult for remote listeners to understand the astronaut s speech and can interfere with the astronaut s attempt to issue vocal commands to a voice-controlled robot. The system could be adapted to terrestrial use in helmets of protective suits that are typically worn in noisy settings: examples include biohazard, fire, rescue, and diving suits. The system (see figure) includes an array of microphones and small loudspeakers mounted at fixed positions in a helmet, amplifiers and signal-routing circuitry, and a commercial digital signal processor (DSP). Notwithstanding the fixed positions of the microphones and loudspeakers, the system can accommodate itself to any normal motion of the wearer s head within the helmet. The system operates in conjunction with a radio transceiver. An audio signal arriving via the transceiver intended to be heard by the wearer is adjusted in volume and otherwise conditioned and sent to the loudspeakers. The wearer s speech is collected by the microphones, the outputs of which are logically combined (phased) so as to form a microphone- array directional sensitivity pattern that discriminates in favor of sounds coming from vicinity of the wearer s mouth and against sounds coming from elsewhere. In the DSP, digitized samples of the microphone outputs are processed to filter out airflow noise and to eliminate feedback from the loudspeakers to the microphones. The resulting conditioned version of the wearer s speech signal is sent to the transceiver.

Helmet wearing in Kenya: prevalence, knowledge, attitude, practice and implications.

Science.gov (United States)

Bachani, A M; Hung, Y W; Mogere, S; Akunga, D; Nyamari, J; Hyder, A A

2017-03-01

many did not always wear a helmet because they found it inconvenient/uncomfortable. Analysis of trauma registry data showed that helmet wearing was associated with a significant reduction in head injuries among motorcyclists (adjusted odds ratio: 0.472, 95% CI: 0.327-0.684). This study highlights the low prevalence of helmet use and documents the potential reduction in the risk of head injuries to motorcyclists if this risk factor was addressed. The passage of a traffic amendment bill showed negligible impact on helmet use. This highlights the need for a multi-faceted strategy that includes media campaigns and widespread enforcement in addition to legislative change for improving helmet use. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Sustainable Product: Personal Protective Equipment Manufactured with Green Plastic

Directory of Open Access Journals (Sweden)

Hamilton Aparecido Boa Vista

2015-04-01

Full Text Available This study analyzed the case of manufacturing of Personal Protective Equipment (PPE using as raw material biopolymers produced from ethanol from sugar cane, known as green polypropylene, produced since 2008 by BRASKEM. This article studied the PPE for the employee’s head protection, named helmet by NR 6, which is used in situations of exposure to weather and work scenarios in places where there is risk of impact from falling or projecting objects, burns, electric shock, and solar radiation. The MSA, green helmet manufacturer, made an inventory of greenhouse gas emissions into the atmosphere by comparing the two manufacturing processes of the helmet shell, covering the January 1 to December 31, 2011 period. It concluded that the sustainable helmet (green polyethylene and pigments robs 231g of CO2 from the atmosphere per produced unit, while the helmet’s production with traditional raw materials (polyethylene and petrochemical pigments found that, for each unit produced, 1029g of CO2 are emitted into the atmosphere. The study showed that substitution of raw materials has led to reduction in the impact generated in the helmets’ production.

Build Your Own Equiluminance Helmet

OpenAIRE

Connolly, Salammbo; Connolly, Denis; Cleary, Anne; Herman, Laura; Cavanagh, Patrick

2017-01-01

A wearable ?helmet? version of the S cone isolating technique was constructed to explore vision at equiluminance. For my high school summer science project, I visited parks and streets while wearing the helmet and report that the helmet appears to have captured the main properties described for the large-scale, more cumbersome stage version.

Materials and design issues for military helmets - Chapter 6

OpenAIRE

Hamouda, A.M.S.; Sohaimi, R.M.; Zaidi, A.M.A.; Abdullah, S.

2012-01-01

Abstract: As weaponry technology has advanced, the ballistic threat to humans has increased significantly. As well as the military, civilians who are exposed to these threats as part of their everyday work require adequate protective equipment. This increasing demand for body armour and ballistic helmets is driving the protective equipment industry to create lightweight, reliable protection adapted for specific applications and marketable to a wide range of consumers. This chapter focuses on ...

Helmet blastometer

Energy Technology Data Exchange (ETDEWEB)

Moss, William C; King, Michael J

2015-03-24

A helmet blastometer for characterizing the direction, speed, magnitude, and duration of a blast event to determine the likelihood of blast-induced traumatic brain injury (biTBI). Time of arrival (TOA) gage sensors are mounted on a rigid outer shell of the helmet each producing a TOA signal in response to a fast rising blast induced positive pressure change above a predetermined threshold. A receiver analyzes the positive pressure changes from the gages to determine direction, speed, and magnitude of a blast. Other TOA gauge sensors can be used to produce a TOA signal in response to a negative pressure change below a predetermined threshold. The positive and negative pressure change TOA signals are used to determine blast duration. A second set of internal contact pressure sensors is connected to an inner liner of the helmet to detect contact pressure on a user's head to determine if biTBI has been sustained.

Federally mandating motorcycle helmets in the United States.

Science.gov (United States)

Eltorai, Adam E M; Simon, Chad; Choi, Ariel; Hsia, Katie; Born, Christopher T; Daniels, Alan H

2016-03-09

Motorcycle helmets reduce both motorcycle-related fatalities and head injuries. Motorcycle crashes are a major public health concern which place economic stress on the U.S. healthcare system. Although statewide universal motorcycle helmet laws effectively increase helmet use, most state helmet laws do not require every motorcycle rider to wear a helmet. Herein, we propose and outline the solution of implementing federal motorcycle helmet law, while addressing potential counterarguments. The decision to ride a motorcycle without a helmet has consequences that affect more than just the motorcyclist. In an effort to prevent unnecessary healthcare costs, injuries, and deaths, public health efforts to increase helmet use through education and legislation should be strongly considered. Helmet use on motorcycles fits squarely within the purview of the federal government public health and economic considerations.

The implementation of a municipal indoor ice skating helmet policy: effects on helmet use, participation and attitudes.

Science.gov (United States)

O'Mahony-Menton, Colleen; Willmore, Jacqueline; Russell, Katherine

2015-12-01

In Ottawa, between 2005 and 2009 there was an annual average of 47.2 head injuries due to ice skating in children and youth (1-19 years of age) requiring a visit to the emergency department, with the highest rates among those aged 5-14 years. Between 2002 and 2007, only 6% of children were wearing a helmet during ice skating when the head injury occurred. During indoor public skating sessions, 93% of children (skating helmet policy coupled with education and promotional activities on helmet use, participation and attitudes towards helmet use. An ice skating helmet policy for children (skating experience at indoor rinks during public skating sessions was developed, implemented and evaluated. Supportive activities such as discount coupons, promotional materials, a media launch, social marketing and staff training are described. The helmet policy was associated with increased helmet use for young children and for older children, youth and adults not included in the policy, without decreasing attendance to public skating sessions. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Inadequate Helmet Fit Increases Concussion Severity in American High School Football Players

Science.gov (United States)

Greenhill, Dustin A.; Navo, Paul; Zhao, Huaqing; Torg, Joseph; Comstock, R. Dawn; Boden, Barry P.

2016-01-01

Background: There is limited information on the relationship between football helmet fit and concussion severity. Hypothesis: Poor helmet fit may predispose football players to a more severe concussion. Study Design: Descriptive epidemiology study. Level of Evidence: Level 3. Methods: Data from concussion injury reports were obtained from the National High School Sports-Related Injury Surveillance System over a 9-year period. Symptoms, duration, and helmet parameters (fit, interior padding) were analyzed for all first-time concussions. Results: Data from 4580 concussions were analyzed. Patients who suffered concussions with a helmet that did not fit properly (3.22%), as determined by an athletic trainer, had higher rates of drowsiness (RR, 1.46; P = 0.005), hyperexcitability (RR, 2.38; P = 0.047), and sensitivity to noise (RR, 1.88; P < 0.001); had more symptoms (5.34 vs 4.54, P = 0.004); and had longer symptom duration (P = 0.04). Athletes with helmets lined with an air bladder had greater rates of sensitivity to light (RR, 1.13; P = 0.02), sensitivity to noise (RR, 1.25; P = 0.009), and longer symptom duration (P = 0.004) compared with foam or gel liners. Conclusion: An improperly fitted football helmet is a risk factor for a concussion with more symptoms and of longer duration. Concussions of longer duration are also more common in players with an air bladder–lined helmet. Current high school football rules should mandate supervision and maintenance of helmet fit throughout the season, prior to impact. Clinical Relevance: Team physicians, athletic trainers, coaches, and high school officials should ensure proper oversight of helmet fit in high school athletes to decrease concussion severity and duration. PMID:27005467

Preventive Effects of Safety Helmets on Traumatic Brain Injury after Work-Related Falls

Directory of Open Access Journals (Sweden)

Sang Chul Kim

2016-10-01

Full Text Available Introduction: Work-related traumatic brain injury (TBI caused by falls is a catastrophic event that leads to disabilities and high socio-medical costs. This study aimed to measure the magnitude of the preventive effect of safety helmets on clinical outcomes and to compare the effect across different heights of fall. Methods: We collected a nationwide, prospective database of work-related injury patients who visited the 10 emergency departments between July 2010 and October 2012. All of the adult patients who experienced work-related fall injuries were eligible, excluding cases with unknown safety helmet use and height of fall. Primary and secondary endpoints were intracranial injury and in-hospital mortality. We calculated adjusted odds ratios (AORs of safety helmet use and height of fall for study outcomes, and adjusted for any potential confounders. Results: A total of 1298 patients who suffered from work-related fall injuries were enrolled. The industrial or construction area was the most common place of fall injury occurrence, and 45.0% were wearing safety helmets at the time of fall injuries. The safety helmet group was less likely to have intracranial injury comparing with the no safety helmet group (the adjusted odds ratios (ORs (95% confidence interval (CI: 0.42 (0.24–0.73, however, there was no statistical difference of in-hospital mortality between two groups (the adjusted ORs (95% CI: 0.83 (0.34–2.03. In the interaction analysis, preventive effects of safety helmet on intracranial injury were significant within 4 m height of fall. Conclusions: A safety helmet is associated with prevention of intracranial injury resulting from work-related fall and the effect is preserved within 4 m height of fall. Therefore, wearing a safety helmet can be an intervention for protecting fall-related intracranial injury in the workplace.

Offsetting or Enhancing Behavior: An Empirical Analysis of Motorcycle Helmet Safety Legislation.

Science.gov (United States)

Lee, Jonathan M

2015-10-01

This study uses state-level panel data from a 33-year period to test the hypotheses of offsetting and enhancing behavior with regards to motorcycle helmet legislation. Results presented in this article find no evidence of offsetting behavior and are consistent with the presence of enhancing behavior. State motorcycle helmet laws are estimated to reduce motorcycle crashes by 18.4% to 31.9%. In the absence of any behavioral adaptations among motorcyclists mandatory helmet laws are not expected to have any significant impact on motorcycle crash rates. The estimated motorcycle crash reductions do not appear to be driven by omitted variable bias or nonclassical measurement error in reported crashes. Overall, the results strongly suggest that mandatory helmet laws yield significant changes in motorcycle mobility in the form of reduced risk taking and/or decreased utilization. © 2015 Society for Risk Analysis.

Motorcycle helmets in Vietnam: ownership, quality, purchase price, and affordability.

Science.gov (United States)

Hung, Dang Viet; Stevenson, Mark R; Ivers, Rebecca Q

2008-06-01

This study investigated motorcycle helmet ownership, quality, purchase price, and affordability in Vietnam. A random sample of motorcyclists was interviewed to investigate aspects of helmet ownership, the purchase price, and affordability of a motorcycle helmet. Multivariate modeling conducted to determine factors associated with the purchase price and affordability of motorcycle helmets. Helmet quality was assessed based on current legal requirements in Vietnam. The prevalence of helmet use in Vietnam remains low (23.3%) despite a high level of helmet ownership (94%), indicating that this is an important area for public health intervention. Overall the quality of helmets appeared to be good; however, few helmets displayed legally required information. Motorcyclists with a high income purchase more helmets for their household rather than more expensive helmets. To ensure that helmets are accessible to the community, policy-makers need to consider pricing motorcycle helmets at a price indicated by the results of this study. Prior to universal motorcycle helmet legislation, the government will also need to ensure that standard helmets are available and that enforcement is at a level to ensure that motorcycle helmets are actually used.

SAFETY ALERT: Electrical insulation defect on safety helmets

CERN Multimedia

HSE Unit

2013-01-01

Contrarily to the information provided until 31 May 2013, some “Euro Protection” safety helmets do not respect any of the requirements for electrical insulation.   This alert concerns the safety helmets identified under the following SCEM numbers: 50.43.30.050.4 white 50.43.30.060.2 yellow 50.43.30.070.0 blue This amounts up to several hundreds of helmets on the CERN site. People who need to wear an electrically insulated safety helmet for their activities, must from now on acquire a duly insulated item to be found on the CERN store under the following SCEM numbers: 50.43.30.210.6: Petzl Vertex ST Helmet (without vent) 50.43.30.300.1: IDRA Helmet with a visor for electrical work As for the people who do not need to wear an electrically insulated helmet for their activities, they can continue working with the aforementioned helmets. For your information, please take note of the maximum use limit of each helmet: “Euro Protection” Safety Helme...

Applying the health action process approach to bicycle helmet use and evaluating a social marketing campaign.

Science.gov (United States)

Karl, Florian M; Smith, Jennifer; Piedt, Shannon; Turcotte, Kate; Pike, Ian

2017-08-05

Bicycle injuries are of concern in Canada. Since helmet use was mandated in 1996 in the province of British Columbia, Canada, use has increased and head injuries have decreased. Despite the law, many cyclists do not wear a helmet. Health action process approach (HAPA) model explains intention and behaviour with self-efficacy, risk perception, outcome expectancies and planning constructs. The present study examines the impact of a social marketing campaign on HAPA constructs in the context of bicycle helmet use. A questionnaire was administered to identify factors determining helmet use. Intention to obey the law, and perceived risk of being caught if not obeying the law were included as additional constructs. Path analysis was used to extract the strongest influences on intention and behaviour. The social marketing campaign was evaluated through t-test comparisons after propensity score matching and generalised linear modelling (GLM) were applied to adjust for the same covariates. 400 cyclists aged 25-54 years completed the questionnaire. Self-efficacy and Intention were most predictive of intention to wear a helmet, which, moderated by planning, strongly predicted behaviour. Perceived risk and outcome expectancies had no significant impact on intention. GLM showed that exposure to the campaign was significantly associated with higher values in self-efficacy, intention and bicycle helmet use. Self-efficacy and planning are important points of action for promoting helmet use. Social marketing campaigns that remind people of appropriate preventive action have an impact on behaviour. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Helmet "tang" from the Metropolitan Museum of Art (New York City, United States. Features of Construction, Design and Operational Use

Directory of Open Access Journals (Sweden)

Leonid A. Bobrov

2016-12-01

Full Text Available The article discusses iron helmet (No. 36.25.115, which is stored in the Metropolitan Museum of art (New York City, United States. For the first time this helmet was published and analyzed by American scientists G. C. Stone and D.G. Alexander. The analysis showed that the Bowl was made by Turkish masters of the XVII century and backplate and the hoop is added to the helmet in 1781–1782 D.G. Alexander speculated that the helmet belonged to the Warrior of the Crimean Khanate. Dating the helmet does not raise objections. However, the attribution of a helmet requires some clarification. Analysis of the design of the helmet and decoration revealed that backplate, hoop and Aventail from iron rings added to Bowl in 1781–1782, were manufactured by Circassian craftsmen living in the Northern Caucasus or in Crimea. For the decoration of the helmet has been used typical Circassian ornaments: "sieve", cherkessian floral pattern, geometric shapes, triangular in shape, "gear", etc. During Assembly of the helmet were applied characteristic of Circassian gunsmiths technological solutions: using as a basis the bowl old-style helmet, tapered Finial with a ring for a decorative plume, hoop with four plates, ringed with aventail lip to protect the forehead, etc. In Circassia similar headgear worn were known as tang (from the Arabic. "Taj", i.e., the "Crown". In the XVII–XVIII centuries. they willingly purchased representatives of Crimean Tatar nobility. Similar in design and system design helmets Circassian production belonged to the highest aristocracy of the Crimean Khanate, are stored in Museum and private collections in Poland, Turkey and the United States. The inscription "Bekmurun" on the hoop from the Metropolitan helmet suggests that it was manufactured on request of Kabardian Bekmur princely heir (Bekmurziny, which moved from Circassia in Crimea, 1737. The popularity of tang type helmets among the aristocracy of North Caucasus and Crimea were due not

Factors Influencing Helmet Use, Head Injury, and Hospitalization Among Children Involved in Skateboarding and Snowboarding Accidents.

Science.gov (United States)

Sadeghian, Homa; Nguyen, Brian; Huynh, Nhan; Rouch, Joshua; Lee, Steven L; Bazargan-Hejazi, Shahrzad

2017-01-01

Up to 75% of skateboarders and snowboarders admitted to the hospital sustain head injuries. It is unclear why not all children and teenagers wear helmets while snowboarding and skateboarding given the protection they afford. To report on the prevalence of, and factors associated with, skateboarding and snowboarding in injured children and to explore factors that influence helmet use, head injury, and hospitalization in this sample. A cross-sectional study of skateboard- and snowboard-associated injuries from 2003 to 2012 among individuals younger than age 18 years using National Electronic Injury Surveillance System (NEISS) data from approximately 100 hospitals. Helmet use, head injury, and hospitalization. Of 1742 patients in the study, 852 (48.9%) and 890 (51.1%) were skateboarders and snowboarders, respectively. Overall, 907 (52.1%) did not use helmets, and 704 (40.4%) sustained head injuries. Multiple logistic regression analysis showed that age, race/ethnicity, location of boarding, and engaging in skateboarding influenced helmet use. Sex, race/ethnicity, helmet use, and skateboarding predicted head injury. Age, sex, skateboarding, and head injury predicted hospital admission. Statistically significant differences exist in helmet use, head injury, and hospitalization rates between skateboarders and snowboarders. Our findings suggest that injury prevention and outreach programs are needed to increase helmet use and reduce the risk of head injury and hospitalization in skateboarders and other at-risk groups. Further studies are needed to clarify the association between race/ethnicity and helmet use among skateboarders and snowboarders.

Helmet-based physiological signal monitoring system.

Science.gov (United States)

Kim, Youn Sung; Baek, Hyun Jae; Kim, Jung Soo; Lee, Haet Bit; Choi, Jong Min; Park, Kwang Suk

2009-02-01

A helmet-based system that was able to monitor the drowsiness of a soldier was developed. The helmet system monitored the electrocardiogram, electrooculogram and electroencephalogram (alpha waves) without constraints. Six dry electrodes were mounted at five locations on the helmet: both temporal sides, forehead region and upper and lower jaw strips. The electrodes were connected to an amplifier that transferred signals to a laptop computer via Bluetooth wireless communication. The system was validated by comparing the signal quality with conventional recording methods. Data were acquired from three healthy male volunteers for 12 min twice a day whilst they were sitting in a chair wearing the sensor-installed helmet. Experimental results showed that physiological signals for the helmet user were measured with acceptable quality without any intrusions on physical activities. The helmet system discriminated between the alert and drowsiness states by detecting blinking and heart rate variability (HRV) parameters extracted from ECG. Blinking duration and eye reopening time were increased during the sleepiness state compared to the alert state. Also, positive peak values of the sleepiness state were much higher, and the negative peaks were much lower than that of the alert state. The LF/HF ratio also decreased during drowsiness. This study shows the feasibility for using this helmet system: the subjects' health status and mental states could be monitored without constraints whilst they were working.

The neurosurgeon as baseball fan and inventor: Walter Dandy and the batter's helmet.

Science.gov (United States)

Brewster, Ryan; Bi, Wenya Linda; Smith, Timothy R; Gormley, William B; Dunn, Ian F; Laws, Edward R

2015-07-01

Baseball maintains one of the highest impact injury rates in all athletics. A principal causative factor is the "beanball," referring to a pitch thrown directly at a batter's head. Frequent morbidities elicited demand for the development of protective gear development in the 20th century. In this setting, Dr. Walter Dandy was commissioned to design a "protective cap" in 1941. His invention became widely adopted by professional baseball and inspired subsequent generations of batting helmets. As a baseball aficionado since his youth, Walter Dandy identified a natural partnership between baseball and medical practice for the reduction of beaning-related brain injuries. This history further supports the unique position of neurosurgeons to leverage clinical insights, inform innovation, and expand service to society.

Injuries and helmet use related to non-motorized wheeled activities among pediatric patients.

Science.gov (United States)

Lindsay, H; Brussoni, M

2014-07-01

Patients presenting to emergency departments (ED) for injuries resulting from recreational activities represent a unique source of information on important directions for injury prevention efforts. We describe the epidemiology of non-motorized wheeled activity-related injury in pediatric patients presenting to Canadian EDs as well as patients' helmet use. Data for the years 2004 to 2009 were abstracted from the Canadian Hospitals Injury Reporting and Prevention Program (CHIRPP), a national ED injury surveillance program in fifteen hospitals. Most of the 28 618 children aged 1 to 16 years injured during non-motorized wheeled activities were injured while cycling, followed by skateboarding. Most injuries occurred among boys. Children injured on scooters tended to be younger whereas skateboarders were the oldest. On average, the number of all injuries decreased by 6% over the time period. Falls were the most common mechanism of injury; 8.3% of patients had head injuries, which were seen more often among cyclists than other wheeled-activity users. Helmet use was greatest among cyclists (62.2%) and lowest among skateboarders (32.9%). Injured patients presenting to EDs in jurisdictions with legislation mandating helmet use had 2.12 greater odds of helmet use and 0.86 lesser odds of head injury compared with those presenting in jurisdictions without helmet laws. These results provide further evidence that legislation mandating helmet use may be an effective way of reducing injury among all wheeled-activity users. The small number of patients who presented with helmet use and protective gear (59.4% overall) suggests that this remains an area for intervention.

Auditory and visual reaction time and peripheral field of vision in helmet users

Directory of Open Access Journals (Sweden)

Abbupillai Adhilakshmi

2016-12-01

Full Text Available Background: The incidence of fatal accidents are more in two wheeler drivers compared to four wheeler drivers. Head injury is of serious concern when recovery and prognosis of the patients are warranted, helmets are being used for safety purposes by moped, scooters and motorcycle drivers. Although, helmets are designed with cushioning effect to prevent head injuries but there are evidences of increase risk of neck injuries and reduced peripheral vision and hearing in helmet users. A complete full coverage helmets provide about less than 3 percent restrictions in horizontal peripheral visual field compared to rider without helmet. The standard company patented ergonomically designed helmets which does not affect the peripheral vision neither auditory reaction time. Objective: This pilot study aimed to evaluate the peripheral field of vision and auditory and visual reaction time in a hypertensive, diabetic and healthy male and female in order to have a better insight of protective characteristics of helmet in health and disease. Method: This pilot study carried out on age matched male of one healthy, one hypertensive and one diabetic and female subject of one healthy, one hypertensive and one diabetics. The field of vision was assessed by Lister’s perimeter whereas auditory and visual reaction time was recorded with response analyser. Result : Gender difference was not noted in peripheral field of vision but mild difference was found in auditory reaction time for high frequency and visual reaction time for both red and green colour in healthy control. But lateral and downward peripheral visual field was found reduced whereas auditory and visual reaction time was found increased in both hypertensive and diabetic subject in both sexes. Conclusion: Peripheral vision, auditory reaction time and visual reaction time in hypertensive and diabetics may lead to vulnerable accident. Helmet use has proven to reduce extent of injury in motorcyclist and

Motorcycle helmets: What about their coating?

Science.gov (United States)

Schnegg, Michaël; Massonnet, Geneviève; Gueissaz, Line

2015-07-01

In traffic accidents involving motorcycles, paint traces can be transferred from the rider's helmet or smeared onto its surface. These traces are usually in the form of chips or smears and are frequently collected for comparison purposes. This research investigates the physical and chemical characteristics of the coatings found on motorcycles helmets. An evaluation of the similarities between helmet and automotive coating systems was also performed.Twenty-seven helmet coatings from 15 different brands and 22 models were considered. One sample per helmet was collected and observed using optical microscopy. FTIR spectroscopy was then used and seven replicate measurements per layer were carried out to study the variability of each coating system (intravariability). Principal Component Analysis (PCA) and Hierarchical Cluster Analysis (HCA) were also performed on the infrared spectra of the clearcoats and basecoats of the data set. The most common systems were composed of two or three layers, consistently involving a clearcoat and basecoat. The coating systems of helmets with composite shells systematically contained a minimum of three layers. FTIR spectroscopy results showed that acrylic urethane and alkyd urethane were the most frequent binders used for clearcoats and basecoats. A high proportion of the coatings were differentiated (more than 95%) based on microscopic examinations. The chemical and physical characteristics of the coatings allowed the differentiation of all but one pair of helmets of the same brand, model and color. Chemometrics (PCA and HCA) corroborated classification based on visual comparisons of the spectra and allowed the study of the whole data set at once (i.e., all spectra of the same layer). Thus, the intravariability of each helmet and its proximity to the others (intervariability) could be more readily assessed. It was also possible to determine the most discriminative chemical variables based on the study of the PCA loadings. Chemometrics

Concussion Characteristics in High School Football by Helmet Age/Recondition Status, Manufacturer, and Model: 2008-2009 Through 2012-2013 Academic Years in the United States.

Science.gov (United States)

Collins, Christy L; McKenzie, Lara B; Ferketich, Amy K; Andridge, Rebecca; Xiang, Huiyun; Comstock, R Dawn

2016-06-01

Football helmets used by high school athletes in the United States should meet the National Operating Committee on Standards for Athletic Equipment performance standards. Despite differences in interior padding and exterior shells, all football helmets should provide comparable protection against concussions. Yet, debate continues on whether differences in the rates or severity of concussions exist based on helmet age/recondition status, manufacturer, or model. To investigate whether high school football concussion characteristics varied by helmet age/recondition status, manufacturer, and model. Descriptive epidemiological study. High school football concussion and helmet data were collected from academic years 2008-2009 through 2012-2013 as part of the National High School Sports-Related Injury Surveillance Study. The certified athletic trainers of participating schools submitted athlete-exposure (AE) and injury information weekly. Participating schools reported 2900 football concussions during 3,528,790 AEs for an overall rate of 8.2 concussions per 10,000 AEs. Concussion rates significantly increased from 2008-2009 through 2012-2013 overall (P = .006) as well as in competition (P = .027) and practice (P = .023). Characteristics of concussed football players (ie, mean number of symptoms, specific concussion symptoms, symptom resolution time, and time until return to play) were similar among players wearing new helmets when compared with reconditioned helmets. Fewer players wearing an old/not reconditioned helmet had concussion symptoms resolve within 1 day compared with players wearing a new helmet. Despite differences in the manufacturers and models of helmets worn by all high school football players compared with players who sustained a concussion, the mean number of concussion symptoms, specific concussion symptoms, symptom resolution time, and time until return to play were similar for concussions sustained by football players wearing the most common helmet

Advanced Extravehicular Helmet Assembly, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The current NASA spacesuit community is focusing on utilizing a 13" hemispherical helmet for the next generation of extravehicular activity spacesuits. This helmet...

Effects of ventilated safety helmets in a hot environment

Science.gov (United States)

G.A. Davis; E.D. Edmisten; R.E. Thomas; R.B. Rummer; D.D. Pascoe

2001-01-01

Forest workers are likely to remove head protection in hot and humid conditions because of thermal discomfort. However, a recent Occupational Safety and Health Administration (OSHA) regulation revision requires all workers in logging operations to wear safety helmets, thus creating a compliance problem. To determine which factors contribute to forest workers’ thermal...

Motorcycle helmet use and the risk of head, neck, and fatal injury: Revisiting the Hurt Study.

Science.gov (United States)

Rice, Thomas M; Troszak, Lara; Ouellet, James V; Erhardt, Taryn; Smith, Gordon S; Tsai, Bor-Wen

2016-06-01

Most studies find strong evidence that motorcycle helmets protect against injury, but a small number of controversial studies have reported a positive association between helmet use and neck injury. The most commonly cited paper is that of Goldstein (1986). Goldstein obtained and reanalyzed data from the Hurt Study, a prospective, on-scene investigation of 900 motorcycle collisions in the city of Los Angeles. The Goldstein results have been adopted by the anti-helmet community to justify resistance to compulsory motorcycle helmet use on the grounds that helmets may cause neck injuries due to their mass. In the current study, we replicated Goldstein's models to understand how he obtained his unexpected results, and we then applied modern statistical methods to estimate the association of motorcycle helmet use with head injury, fatal injury, and neck injury among collision-involved motorcyclists. We found Goldstein's analysis to be critically flawed due to improper data imputation, modeling of extremely sparse data, and misinterpretation of model coefficients. Our new analysis showed that motorcycle helmets were associated with markedly lower risk of head injury (RR 0.40, 95% CI 0.31-0.52) and fatal injury (RR 0.44, 95% CI 0.26-0.74) and with moderately lower but statistically significant risk of neck injury (RR 0.63, 95% CI 0.40-0.99), after controlling for multiple potential confounders. Copyright © 2016 Elsevier Ltd. All rights reserved.

Injury outcome among helmeted and non-helmeted motorcycle ...

African Journals Online (AJOL)

users are vulnerable on the road and are at high risk of death resulting from head ..... time of injury sustained head injury reflecting its importance in prevention of head .... WHO (2006) Helmets: A Road Safety Manual for Decision-makers and ...

A study of emergency American football helmet removal techniques.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Decoster, Laura C; Hernandez, Adam E

2012-09-01

The purpose was to compare head kinematics between the Eject Helmet Removal System and manual football helmet removal. This quasi-experimental study was conducted in a controlled laboratory setting. Thirty-two certified athletic trainers (sex, 19 male and 13 female; age, 33 ± 10 years; height, 175 ± 12 cm; mass, 86 ± 20 kg) removed a football helmet from a healthy model under 2 conditions: manual helmet removal and Eject system helmet removal. A 6-camera motion capture system recorded 3-dimensional head position. Our outcome measures consisted of the average angular velocity and acceleration of the head in each movement plane (sagittal, frontal, and transverse), the resultant angular velocity and acceleration, and total motion. Paired-samples t tests compared each variable across the 2 techniques. Manual helmet removal elicited greater average angular velocity in the sagittal and transverse planes and greater resultant angular velocity compared with the Eject system. No differences were observed in average angular acceleration in any single plane of movement; however, the resultant angular acceleration was greater during manual helmet removal. The Eject Helmet Removal System induced greater total head motion. Although the Eject system created more motion at the head, removing a helmet manually resulted in more sudden perturbations as identified by resultant velocity and acceleration of the head. The implications of these findings relate to the care of all cervical spine-injured patients in emergency medical settings, particularly in scenarios where helmet removal is necessary. Copyright © 2012 Elsevier Inc. All rights reserved.

A series of student design projects for improving and modernizing safety helmets

NARCIS (Netherlands)

Beurden, van K.M.M. (Karin); Boer, de J. (Johannes); Stilma, M. (Margot); Teeuw, W.B. (Wouter)

2014-01-01

The Saxion Research Centre for Design and Technology employs many students during research projects. This paper discusses a series of student design projects on safety helmets in the Safety@Work project. At construction sites workers are required to wear personal protective equipment during their

77 FR 48105 - Federal Motor Vehicle Safety Standards; Motorcycle Helmets

Science.gov (United States)

2012-08-13

... [Docket No. NHTSA-2012-0112] Federal Motor Vehicle Safety Standards; Motorcycle Helmets AGENCY: National... Vehicle Safety Standard for motorcycle helmets. Specifically, the final rule amended the helmet labeling... compliance test procedures of FMVSS No. 218, Motorcycle helmets, in order to make it more difficult to...

Head and Helmet Biodynamics and Tracking Performance in Vibration Environments

National Research Council Canada - National Science Library

Smith, Suzanne D; Smith, Jeanne A

2006-01-01

...) and Up (40" elevation, 0" azimuth)], and three helmet CCs were tested. The overall head, helmet, and helmet slippage displacement rotations, and rms tracking error and percent time-on-target were evaluated...

Associations between drug use and motorcycle helmet use in fatal crashes.

Science.gov (United States)

Rossheim, Matthew E; Wilson, Fernando; Suzuki, Sumihiro; Rodriguez, Mayra; Walters, Scott; Thombs, Dennis L

2014-01-01

Helmet use reduces mortality risk for motorcyclists, regardless of drug and alcohol use. However, the association between drug use and motorcycle helmet utilization is not well known. This study examines the relationship between drug use and motorcycle helmet use among fatally injured motorcycle riders. Using data from the 2005-2009 Fatality Analysis Reporting System (FARS), we examined the association between drug use and motorcycle helmet use in a multivariable logistic regression analysis of 9861 fatally injured motorcycle riders in the United States. For fatally injured motorcycle riders, use of alcohol, marijuana, or other drugs was associated with increased odds of not wearing a motorcycle helmet, controlling for the effects of state motorcycle helmet laws and other confounding variables. Predicted probabilities indicate that helmet use substantially decreases among fatally injured riders mixing alcohol with marijuana and other drugs. Furthermore, the likelihood of helmet use between marijuana-only users and other drug users is virtually the same across all blood alcohol content (BAC) levels. This study provides evidence that alcohol, marijuana, and other drug use is associated with not wearing a motorcycle helmet in fatal motorcycle crashes. There is a clear need for additional prevention and intervention efforts that seek to change helmet and drug use norms among motorcycle riders.

What do we know about bicycle helmets?

NARCIS (Netherlands)

Bogerd, C.P. Halldin, P. Houtenbos, M. Otte, D. Rossi, R.M. Walker, L. Willinger, R. & Shinar, D.

2012-01-01

Cycling is an excellent sustainable alternative to driving for many journeys. But cyclists have fewer safety options than car-users, with a helmet being the main safety device that is available. However, there are indications that increasing bicycle helmet usage through legislation causes

The physiological demands of horseback mustering when wearing an equestrian helmet.

Science.gov (United States)

Taylor, Nigel A S; Caldwell, Joanne N; Dyer, Rodd

2008-09-01

The hottest months on northern Australian cattle stations are from September to November, and it is during these months that horseback cattle mustering occurs. Stockmen wear clothing that restricts heat loss, and protective helmets have recently been introduced. Anecdotal evidence points to the possibility that helmets may increase the probability of developing heat illness, or reducing workplace performance. In this project, we quantified the working (thermal) environment on such cattle stations, and measured the metabolic demands on, and concurrent physiological strain in stockmen during mustering, whilst wearing an equestrian helmet. During horseback work, the average heart rate was 102.0 beats min(-1) (SD 14.0), with almost 90% of the time (238 min) spent working at intensities <50% of the heart rate reserve. The projected metabolic heat production during mustering ranged between 178 and 333 W (women), and between 212 and 542 W (men). The average core temperature was 37.6 degrees C, while the mean skin temperature averaged 34.1 degrees C. It was concluded that the working environment is, on average, thermally uncompensable during the mustering season. However, horseback mustering per se is a relatively low-intensity activity, interspersed with short periods of high-intensity work. This activity level was reflected within core temperatures, which rarely climbed above values associated with light-moderate exercise. Thus, whilst the climatic state was uncompensable, stockmen used behavioural strategies to minimise the risk of heat illness. Finally, it was observed that the helmet, though unpleasant to wear, did not appear to increase thermal strain in a manner that would disadvantage stockmen.

Helmet-induced headache among Danish military personnel.

Science.gov (United States)

Rahmani, Zakia; Kochanek, Aneta; Astrup, Jesper Johnsen; Poulsen, Jeppe Nørgaard; Gazerani, Parisa

2017-12-01

External compression headache is defined as a headache caused by an external physical compression applied on the head. It affects about 4% of the general population; however, certain populations (e.g. construction workers and military personnel) with particular needs of headwear or helmet are at higher risk of developing this type of headache. External compression headache is poorly studied in relation to specific populations. This study aimed to investigate the prevalence and pattern of helmet-induced external compression headache among Danish military personnel of the Northern Jutland region in Denmark. Data acquisition was based on a custom-made questionnaire delivered to volunteers who used helmets in the Danish military service and who agreed to participate in this study. The military of the Northern Jutland region of Denmark facilitated recruitment of the participants. The questionnaires were delivered on paper and the collected (anonymous) answers (total 279) were used for further analysis. About 30% of the study participants reported headache in relation to wearing a military helmet. Headache was defined as a pressing pain predominantly in the front of the head with an average intensity of 4 on a visual analogue scale of 0 (no pain) to 10 (worst pain imaginable). It was also found that helmets with different designs influenced both the occurrence of headache and its characteristics. This study is the first to demonstrate the prevalence and pattern of compression headache among military personnel in North Jutland, Denmark. The findings of this study call for further attention to helmet-induced external compression headache and strategies to minimize the burden.

Examination of factors associated with use rates after transition from a universal to partial motorcycle helmet use law.

Science.gov (United States)

Russo, Brendan J; Barrette, Timothy P; Morden, Jeffery; Savolainen, Peter T; Gates, Timothy J

2017-01-02

the short-term reduction in helmet use following transition from a universal to partial motorcycle helmet law. The reduction in use is somewhat less pronounced than has been experienced in other states, which may be reflective of general differences among Michigan motorcyclists because the state has also generally exhibited higher use rates of seat belts and other forms of occupant protection. The study results also highlight potential target areas for subsequent education and public awareness initiatives aimed at increasing helmet use.

Universal Motorcycle Helmet Laws to Reduce Injuries: A Community Guide Systematic Review.

Science.gov (United States)

Peng, Yinan; Vaidya, Namita; Finnie, Ramona; Reynolds, Jeffrey; Dumitru, Cristian; Njie, Gibril; Elder, Randy; Ivers, Rebecca; Sakashita, Chika; Shults, Ruth A; Sleet, David A; Compton, Richard P

2017-06-01

Motorcycle crashes account for a disproportionate number of motor vehicle deaths and injuries in the U.S. Motorcycle helmet use can lead to an estimated 42% reduction in risk for fatal injuries and a 69% reduction in risk for head injuries. However, helmet use in the U.S. has been declining and was at 60% in 2013. The current review examines the effectiveness of motorcycle helmet laws in increasing helmet use and reducing motorcycle-related deaths and injuries. Databases relevant to health or transportation were searched from database inception to August 2012. Reference lists of reviews, reports, and gray literature were also searched. Analysis of the data was completed in 2014. A total of 60 U.S. studies qualified for inclusion in the review. Implementing universal helmet laws increased helmet use (median, 47 percentage points); reduced total deaths (median, -32%) and deaths per registered motorcycle (median, -29%); and reduced total injuries (median, -32%) and injuries per registered motorcycle (median, -24%). Repealing universal helmet laws decreased helmet use (median, -39 percentage points); increased total deaths (median, 42%) and deaths per registered motorcycle (median, 24%); and increased total injuries (median, 41%) and injuries per registered motorcycle (median, 8%). Universal helmet laws are effective in increasing motorcycle helmet use and reducing deaths and injuries. These laws are effective for motorcyclists of all ages, including younger operators and passengers who would have already been covered by partial helmet laws. Repealing universal helmet laws decreased helmet use and increased deaths and injuries. Published by Elsevier Inc.

Measurement of Gamma Knife registered helmet factors using MOSFETs

International Nuclear Information System (INIS)

Kurjewicz, Laryssa; Berndt, Anita

2007-01-01

The relative dose rate for the different Gamma Knife registered helmets (4, 8, 14, and 18 mm) is characterized by their respective helmet factors. Since the plateau of the dose profile for the 4 mm helmet is at most 1 mm wide, detector choices are limited. Traditionally helmet factors have been measured using 1x1x1 mm 3 thermoluminescent dosimeters (TLDs). However, these are time-consuming, cumbersome measurements. This article investigates the use of metal-oxide-semiconductor field effect transistors (MOSFETs) (active area of 0.2x0.2 mm 2 ) as a more accurate and convenient dosimeter. Their suitability for these measurements was confirmed by basic characterization measurements. Helmet factors were measured using both MOSFETs and the established TLD approach. A custom MOSFET cassette was designed in analogy to the Elekta TLD cassette (Elekta Instruments AB) for use with the Elekta dosimetry sphere. Although both dosimeters provided values within 3% of the manufacturer's suggestion, MOSFETs provided superior accuracy and precision, in a fraction of the time required for the TLD measurements. Thus, MOSFETs proved to be a reasonable alternative to TLDs for performing helmet factor measurements

Passengers' attitudes and behaviour towards motorcycle helmet use ...

African Journals Online (AJOL)

Passengers' attitudes and behaviour towards motorcycle helmet use in Ilorin, ... Remember me ... The purpose of this study was to examine the attitudes, knowledge, and behavior of motorcycle passengers to helmet use in Ilorin metropolis, ...

How motorcycle helmets affect trauma mortality: Clinical and policy implications.

Science.gov (United States)

Lee, Jwo-Leun; Chen, Tzu-Chun; Huang, Hung-Chang; Chen, Ray-Jade

2017-08-18

Motorcycles are the most popular vehicles in Taiwan, where more than 14.8 million motorcycles (1 motorcycle per 1.6 people) are in service. Despite the mandatory helmet law passed in 1997, less than 80% of motorcyclists in Taiwan wear helmets. The objective of this study was to analyze the effect of using motorcycle helmets on fatality rates. A clinical data set including 2,868 trauma patients was analyzed; the cross-sectional registration database was administered by a university medical center in Central Taiwan. A path analysis framework and multiple logistic regressions were used to estimate the marginal effect of helmet use on mortality. Using a helmet did not directly reduce the mortality rate but rather indirectly reduced the mortality rate through intervening variables such as the severity of head injuries, number of craniotomies, and complications during therapeutic processes. Wearing a helmet can reduce the fatality rate by 1.3%, the rate of severe head injury by 34.5%, the craniotomy rate by 7.8%, and the rate of complications during therapeutic processes by 1.5%. These rates comprise 33.3% of the mortality rate for people who do not wear helmets, 67.3% of the severe head injury rate, 60.0% of the craniotomy rate, and 12.2% of the rate of complications during therapeutic processes. Wearing a helmet and trauma system designation are crucial factors that reduce the fatality rate.

Does law enforcement awareness affect motorcycle helmet use? evidence from urban cities in Thailand.

Science.gov (United States)

Jiwattanakulpaisarn, Piyapong; Kanitpong, Kunnawee; Ponboon, Sattrawut; Boontob, Nuttapong; Aniwattakulchai, Pakorn; Samranjit, Supattra

2013-09-01

Although helmet use has been compulsory for motorcycle drivers and passengers in Thailand since the enactment of the Helmet Act in 1994, recent surveys show that the prevalence of helmet usage remains low, particularly among passengers. This paper has sought to explore motorcyclists' awareness of helmet law enforcement in Thailand and examine whether it affects their helmet use behaviour. A total of 2,429 drivers and 1,328 passengers in urban cities nationwide were interviewed in 2009, and the data were analysed using a multivariate ordered logit regression technique. About 60% of the drivers and only 28% of the passengers reported that they always wore a motorcycle helmet. Apart from basic demographics (i.e. age and gender) and riding frequency, our analysis reveals that the awareness of helmet law enforcement was among the contributing factors influencing the use of motorcycle helmets in Thailand. Regardless of riding position, the prevalence of helmet use tended to be greater among those frequently observing the police's checkpoints for helmet wearing and those perceiving the high risk of being caught for non-helmet use. However, the use of helmets appeared to be lower among drivers who perceived the checkpoints to take place at the same times and locations, which were likely predicted. For motorcycle passengers, it was found that the low prevalence of helmet use was potentially attributable to the absence of knowledge on the compulsory helmet law for passengers and the perception that the law was not enforced by the police. Thus, if motorcycle helmet use in Thailand is to be increased, considerable efforts need to be given to increasing the perceived risk of apprehension for non-helmet use (e.g. more police presence and random scheduling of enforcement activities), improving the awareness of the existing helmet law for passengers, and ensuring that helmet wearing by passengers is more strictly enforced.

Helmet Ownership and Use among Skateboarders: Utilisation of the Health Belief Model

Science.gov (United States)

Peachey, Andrew A.; Sutton, Debra L.; Cathorall, Michelle L.

2016-01-01

Introduction: The purpose of this study was to determine the proportion of skateboarders who owned and who wore a helmet and which constructs from the Health Belief Model predicted helmet ownership and helmet use among undergraduate skateboarders. Methods: From March 2013 through March 2014, 83 skateboarders completed a helmet attitude and use…

Camouflage design and head measurement characteristic of Indonesian armoured vehicle helmet

Science.gov (United States)

Sya'bana, Yukhi Mustaqim Kusuma; Sanjaya, K. H.

2017-01-01

In this paper discussed camouflage design helmet for armored vehicles with comparing head measurement of Indonesian anthropometric. Design process conduct with considering of design aspects involves function, materials, operational, technology, user, and appearance (camouflage). As an application of Indonesian National Army that qualifies factors needs: safety, comfort, practical and service. MIL-H-44099A Military Specification: Helmet, Ground Troops And Parachutists is minimum limitation standard of military helmet production. Head measurement for product design process guide is presented. Model simulation and helmet measurement using the design for ego and design for more types ergonomics concept. Appearance shape concept is engaging camouflage towards background and environment to deceive enemy viewpoint. Helmet prototype has tested ergonomically to an Indonesian National Army soldier and stated that the helmet size is a comfort and fitted on the head when in use.

Long-term use of neonatal helmet-CPAP: a case report.

Science.gov (United States)

Doglioni, N; Micaglio, M; Zanardo, V; Trevisanuto, D

2009-12-01

In a recent short-term physiological study, we demonstrated a new continuous positive airway pressure (CPAP) system (neonatal helmet-CPAP) that could be a feasible device for managing preterm infants needing continuous distending pressure with better tolerability than nasal-CPAP. However, its application for a long-term period has never been reported in neonates. Here, we describe the use of neonatal helmet-CPAP in a neonate with persistent pulmonary hypertension of the newborn. Twenty minutes after neonatal helmet-CPAP placement, the baseline post-ductal tcSaO2 (66%) and alveolar-arterial gradient O2 improved from 66% and 648 mmHg to 100% and 465 mmHg, respectively. The neonatal helmet-CPAP was applied for 48 hours and was well-tolerated by the patient without complications. Long-term use of neonatal helmet-CPAP appears feasible and well-tolerated. Comparative trials are needed.

X-ray, synchrotron, and neutron diffraction analysis of Roman cavalry parade helmet fragment

Czech Academy of Sciences Publication Activity Database

Smrcok, L.; Petrik, I.; Langer, V.; Filinchuk, Y.; Beran, Přemysl

2010-01-01

Roč. 45, č. 10 (2010), s. 1025-1031 ISSN 0232-1300 Institutional research plan: CEZ:AV0Z10480505 Keywords : archaeometry * Roman helmet * phase analysis Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 0.946, year: 2010

Head impact in a snowboarding accident.

Science.gov (United States)

Bailly, N; Llari, M; Donnadieu, T; Masson, C; Arnoux, P J

2017-09-01

To effectively prevent sport traumatic brain injury (TBI), means of protection need to be designed and tested in relation to the reality of head impact. This study quantifies head impacts during a typical snowboarding accident to evaluate helmet standards. A snowboarder numerical model was proposed, validated against experimental data, and used to quantify the influence of accident conditions (speed, snow stiffness, morphology, and position) on head impacts (locations, velocities, and accelerations) and injury risk during snowboarding backward falls. Three hundred twenty-four scenarios were simulated: 70% presented a high risk of mild TBI (head peak acceleration >80 g) and 15% presented a high risk of severe TBI (head injury criterion >1000). Snow stiffness, speed, and snowboarder morphology were the main factors influencing head impact metrics. Mean normal head impact speed (28 ± 6 km/h) was higher than equivalent impact speed used in American standard helmet test (ASTM F2040), and mean tangential impact speed, not included in standard tests, was 13.8 (±7 km/h). In 97% of simulated impacts, the peak head acceleration was below 300 g, which is the pass/fail criteria used in standard tests. Results suggest that initial speed, impacted surface, and pass/fail criteria used in helmet standard performance tests do not fully reflect magnitude and variability of snowboarding backward-fall impacts. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

42 CFR 84.135 - Half-mask facepieces, full facepieces, hoods, and helmets; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods, and... OF RESPIRATORY PROTECTIVE DEVICES Supplied-Air Respirators § 84.135 Half-mask facepieces, full facepieces, hoods, and helmets; fit; minimum requirements. (a) Half-mask facepieces and full facepieces shall...

Helmet use and associated factors among motorcyclists in the ...

African Journals Online (AJOL)

opperwjj

in Malaysia and the highest (10) in Brunei Duressalam. Stricter .... in line with the global findings that the introduction and enforcement of legislation on helmet .... Motorcycle helmet wearing behavior among Naresuan university students.

Prehospital emergency removal of football helmets using two techniques.

Science.gov (United States)

Swartz, Erik E; Hernandez, Adam E; Decoster, Laura C; Mihalik, Jason P; Burns, Matthew F; Reynolds, Cathryn

2011-01-01

To compare the Eject Helmet Removal (EHR) System with manual football helmet removal. This quasiexperimental counterbalanced study was conducted in a controlled laboratory setting. Thirty certified athletic trainers (17 men and 13 women; mean ± standard deviation age: 33.03 ± 10.02 years; height: 174.53 ± 12.04 cm; mass: 85.19 ± 19.84 kg) participated after providing informed consent. Participants removed a Riddell Revolution IQ football helmet from a healthy model two times each under two conditions: manual helmet removal (MHR) and removal with the EHR system. A six-camera, three-dimensional motion capture system was used to record range of motion (ROM) of the head. A digital stopwatch was used to time trials and to record a split time associated with EHR system bladder insertion. A modified Borg CR10 scale was used to measure the rating of perceived exertion (RPE). Mean values were created for each variable. Three pairwise t-tests with Bonferroni-corrected alpha levels tested for differences between time for removal, split time, and RPE. A 2 x 3 (condition x plane) totally within-subjects repeated-measures design analysis of variance (ANOVA) tested for differences in head ROM between the sagittal, frontal, and transverse planes. Analyses were performed using SPSS (version 18.0) (alpha = 0.05). There was no statistically significant difference in perceived difficulty between EHR (RPE = 2.73) and MHR (RPE = 2.55) (t(29) = 0.76; p = 0.45; d = 0.20). Manual helmet removal was, on average, 28.95 seconds faster than EHR (t(29) = 11.44; p football helmets and in helmets used in other sports such as lacrosse, motorsports, and ice hockey.

Aircrew helmet design and manufacturing enhancements through the use of advanced technologies

Science.gov (United States)

Cadogan, David P.; George, Alan E.; Winkler, Edward R.

1993-12-01

With the development of helmet mounted displays (HMD) and night vision systems (NVS) for use in military and civil aviation roles, new methods of helmet development need to be explored. The helmet must be designed to provide the user with the most lightweight, form fitting system, while meeting other system performance requirements. This can be achieved through a complete analysis of the system requirements. One such technique for systems analysis, a quality function deployment (QFD) matrix, is explored for this purpose. The advanced helmet development process for developing aircrew helmets includes the utilization of several emerging technologies such as laser scanning, computer aided design (CAD), computer generated patterns from 3-D surfaces, laser cutting of patterns and components, and rapid prototyping (stereolithography). Advanced anthropometry methods for helmet development are also available for use. Besides the application of advanced technologies to be used in the development of helmet assemblies, methods of mass reduction are also discussed. The use of these advanced technologies will minimize errors in the development cycle of the helmet and molds, and should enhance system performance while reducing development time and cost.

Evaluation of the Effects of Variable Helmet Weight on Human Response During Lateral +Gy Impact

National Research Council Canada - National Science Library

Perry, Chris

2003-01-01

.... A series of tests was conducted by AFRL/HEPA on a horizontal impulse accelerator using human subjects to investigate the effects of helmet inertial properties on human response to short duration...

The European, Japanese and US protective helmet, gloves and boots for firefighters: thermoregulatory and psychological evaluations.

Science.gov (United States)

Lee, Joo-Young; Yamamoto, Yota; Oe, Riichi; Son, Su-Young; Wakabayashi, Hitoshi; Tochihara, Yutaka

2014-01-01

The purpose of this study was to investigate the physiological and subjective responses of the European, Japanese (JPN) and US firefighters' helmet, gloves and boots for international standardisation. Three experimental conditions were evaluated (clothing mass: 9.4, 8.2 and 10.1 kg for the three conditions, respectively) at the air temperature of 32°C and 60% relative humidity. The results showed that there was no significant difference among the three conditions in oxygen consumption, heart rate, total sweat rate, rectal temperature and mean skin temperature, whereas peripheral temperatures and subjective perceptions were lower in the JPN condition than in the other conditions (P < 0.05). These results indicate that a 0.5-kg reduction in helmet mass and a 1.1-kg reduction in boot mass during exercise resulted in a significant decrease in head and leg temperatures and subjective perceptions, while a 1.9-kg reduction in total clothing mass had insignificant influences on the metabolic burden and overall body temperature.

42 CFR 84.198 - Half-mask facepieces, full facepieces, mouthpieces, hoods, and helmets; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, mouthpieces... APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Chemical Cartridge Respirators § 84.198 Half-mask facepieces, full facepieces, mouthpieces, hoods, and helmets; fit; minimum requirements. (a) Half-mask facepieces...

Power Measurements for Microvision, Inc., Aircrew Integrated Helmet System Scanning Laser Helmet-Mounted Display

National Research Council Canada - National Science Library

Rash, Clarence

2002-01-01

...) technology based on scanning lasers. Under this program, Microvision, Inc., Bothell, Washington, has developed a scanning laser HMD prototype for use with the Aircrew Integrated Helmet System (AIHS...

The problem of the pillion rider: India's helmet law and New Delhi's exemption.

Science.gov (United States)

Swaroop, Mamta; Marie Siddiqui, Selma; Sagar, Sushma; Crandall, Marie L

2014-05-01

In India, motorized two-wheeler (MTW) road traffic accidents injure or kill 72,000 women annually. Before the Motor Vehicle Act of 1988, which required mandatory helmet use for MTW riders, a study found 0.6% of all MTW pillions (backseat passengers) were helmeted. Citing religious protests to the legislation, Delhi's high court exempted the city's 12 million women from the law. We hypothesize that currently male pillions use helmets more frequently than females, and that overall pillion helmet usage has increased over the last 20 y. Continuous video was recorded in half-hour blocks at four locations in Delhi on separate days, totaling 8 hours of high- and low-volume traffic. Videos were reviewed with at least two reviewers extracting the number of MTW pillions, as well as their gender, approximate age, and helmet usage. Of 4010 pillions identified, 63.8% were male, 32.4% female, and 3.3% children. Among males, there were significantly more helmeted pillions (88.4%, P < 0.001); among females, there were significantly more unhelmeted pillions (99.4%, P < 0.001). Among unhelmeted pillions, significantly more were female (81.4%) than male (P < 0.001). Current overall pillion helmet use is significantly higher than historical rate (P < 0.001). The significantly higher male pillion helmet usage compared with females indicates Delhi's helmet law is associated with increased compliance among those who fall under its jurisdiction. This augments the growing body of evidence that mandatory helmet laws are efficacious, thus repealing the exemption of women is an important step in increasing female pillion helmet usage. Copyright © 2014 Elsevier Inc. All rights reserved.

Neck Muscle Fatigue Resulting from Prolonged Wear of Weighted Helmets

National Research Council Canada - National Science Library

Gallagher, Hilary L; Caldwell, Erin; ALbery, Christopher B

2008-01-01

.... While these systems undoubtedly increase a pilot's capabilities, one obvious drawback to putting all this equipment on the pilot's helmet is the increase in helmet weight that shifts the combined...

The Influence of Friction Between Football Helmet and Jersey Materials on Force: A Consideration for Sport Safety.

Science.gov (United States)

Rossi, Anthony M; Claiborne, Tina L; Thompson, Gregory B; Todaro, Stacey

2016-09-01

The pocketing effect of helmet padding helps to dissipate forces experienced by the head, but if the player's helmet remains stationary in an opponent's shoulder pads, the compressive force on the cervical spine may increase. To (1) measure the coefficient of static friction between different football helmet finishes and football jersey fabrics and (2) calculate the potential amount of force on a player's helmet due to the amount of friction present. Cross-sectional study. Laboratory. Helmets with different finishes and different football jersey fabrics. The coefficient of friction was determined for 2 helmet samples (glossy and matte), 3 football jerseys (collegiate, high school, and youth), and 3 types of jersey numbers (silkscreened, sublimated, and stitched on) using the TAPPI T 815 standard method. These measurements determined which helmet-to-helmet, helmet-to-jersey number, and helmet-to-jersey material combination resulted in the least amount of static friction. The glossy helmet versus glossy helmet combination produced a greater amount of static friction than the other 2 helmet combinations (P = .013). The glossy helmet versus collegiate jersey combination produced a greater amount of static friction than the other helmet-to-jersey material combinations (P < .01). The glossy helmet versus silkscreened numbers combination produced a greater amount of static friction than the other helmet-to-jersey number combinations (P < .01). The force of static friction experienced during collisions can be clinically relevant. Conditions with higher coefficients of static friction result in greater forces. In this study, the highest coefficient of friction (glossy helmet versus silkscreened number) could increase the forces on the player's helmet by 3553.88 N when compared with other helmet-to-jersey combinations. Our results indicate that the makeup of helmet and uniform materials may affect sport safety.

Brain injury in sports.

Science.gov (United States)

Lloyd, John; Conidi, Frank

2016-03-01

Helmets are used for sports, military, and transportation to protect against impact forces and associated injuries. The common belief among end users is that the helmet protects the whole head, including the brain. However, current consensus among biomechanists and sports neurologists indicates that helmets do not provide significant protection against concussion and brain injuries. In this paper the authors present existing scientific evidence on the mechanisms underlying traumatic head and brain injuries, along with a biomechanical evaluation of 21 current and retired football helmets. The National Operating Committee on Standards for Athletic Equipment (NOCSAE) standard test apparatus was modified and validated for impact testing of protective headwear to include the measurement of both linear and angular kinematics. From a drop height of 2.0 m onto a flat steel anvil, each football helmet was impacted 5 times in the occipital area. Skull fracture risk was determined for each of the current varsity football helmets by calculating the percentage reduction in linear acceleration relative to a 140-g skull fracture threshold. Risk of subdural hematoma was determined by calculating the percentage reduction in angular acceleration relative to the bridging vein failure threshold, computed as a function of impact duration. Ranking the helmets according to their performance under these criteria, the authors determined that the Schutt Vengeance performed the best overall. The study findings demonstrated that not all football helmets provide equal or adequate protection against either focal head injuries or traumatic brain injuries. In fact, some of the most popular helmets on the field ranked among the worst. While protection is improving, none of the current or retired varsity football helmets can provide absolute protection against brain injuries, including concussions and subdural hematomas. To maximize protection against head and brain injuries for football players of

Predictions of Helmet Pad Suspension System Performance using Isolated Pad Impact Results

Science.gov (United States)

2010-09-13

Equation 2 and Equation 3, respectively. 3. METHOD The primary method of data collection for this report is detailed in the 2008 Joint Live Fire ...tests and the helmet system tests (see Figure 3). All testing was performed with a monorail drop tower (see Figure 4) at three conditioning...right) and system test setup (right and center left) Figure 5. MEP monorail drop test setup with a hemispherical impactor (left and center left

Implementation of an all-ages mandatory helmet policy for ice skating.

Science.gov (United States)

Thibault-Halman, Ginette; Fenerty, Lynne; Wheadon-Hore, Kathie; Walling, Simon; Cusimano, Michael D; Clarke, David B

2015-12-01

Ice skaters sustain a significant number of head injuries each winter. We are the first to implement an all-ages helmet policy at a university-based Canadian arena. We report our experience from a cross-sectional observational study as well as the policy's consequences on helmet use and skating participation. Educational programming was provided prior to policy implementation. Observations of helmet use, falls and skater demographics were conducted prior to education/implementation and after policy implementation. The number of skaters observed was essentially unchanged by the policy; 361 skaters were observed pre-implementation, while 358 were observed post-implementation during the same number of observation-hours. Pre-implementation, helmet use ranged from 97% among children under 12 to 10% among adults; post-implementation use in all skaters was 99%. Falls were observed among all age groups, with preponderance among those aged 4-12. An all-ages helmet policy was successful both in achieving helmet use among all skaters and in maintaining participation rates. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Helmet Use and Associated Factors among Thai Motorcyclists during Songkran Festival

Science.gov (United States)

Siviroj, Penprapa; Peltzer, Karl; Pengpid, Supa; Morarit, Sompong

2012-01-01

The aim of this study was to assess helmet use and associated factors among motorcycle riders during Songkran festival in Thailand. A cross-sectional survey was conducted to determine the prevalence of helmet use among Thai motorcycle riders (sample size = 18,998) during four days of the Songkran festival. For this sample, the population of motorcycle riders was consecutively selected using quota sampling from 12 petrol stations in four provinces from each of the four main geographical regions of Thailand. The study was conducted at petrol stations at roads in town, outside town and highway at different time intervals when trained field staff administered a structured questionnaire and performed an observation checklist. Results indicate that 44.2% of the motorcycle riders and 72.5% of the motorcycle passengers had not been using a helmet. In multivariable analysis demographics, environmental factors, helmet use experiences and attitudes and recalling a lower exposure to road safety awareness (RSA) campaign were associated with non-helmet use among motorcyclists. It appears that the RSA campaign may have some positive effect on reducing non-helmet use among motorcycle riders during the Songkran festival. PMID:23202686

DETECTION OF MOTORCYCLISTS WITHOUT HELMET AND FINEPAYMENT USING OPEN CV

OpenAIRE

Stemy Simon, Divya Kumaran A.K.

2018-01-01

The helmet is the main safety equipment of motorcyclists, but many drivers do not use it. The main aim of this project is to construct an automatic detection of the motorcyclist without helmet from video using OpenCV library tools. If they are not wearing the helmet, the license plate of the motorcycle is focused automatically. By using Computer Vision technique we can detect and recognize the license plate number. We make the training set of different characters of different sizes. Based on ...

Psychological models for development of motorcycle helmet use among students in Vietnam

Science.gov (United States)

Kumphong, J.; Satiennam, T.; Satiennam, W.; Trinh, Tu Anh

2018-04-01

A helmet can reduce head accident severity. The aim of this research study was to study the intention for helmet use of students who ride motorcycles in Vietnam, by Structural Equation Modeling (SEM). Questionnaires developed by several traffic psychology modules, including the Theory of Planned Behaviour (TPB), Traffic Locus of Control (T-LOC), and Health Belief Model (HBM), were distributed to students at Ton Thang University and University of Architecture, Ho Chi Minh City. SEM was used to explain helmet use behaviour. The results indicate that TPB, T-LOC and HBM could explain the variance in helmet use behaviour. However, TPB can explain behaviour (helmet use intention) better than T-LOC and HBM. The outcome of this study is useful for the agencies responsible to improve motorcycle safety.

Modular liquid-cooled helmet liner for thermal comfort

Science.gov (United States)

Williams, B. A.; Shitzer, A.

1974-01-01

A modular liquid-cooled helmet liner made of eight form-fitting neoprene patches was constructed. The liner was integrated into the sweatband of an Army SPH-4 helicopter aircrew helmet. This assembly was tested on four subjects seated in a hot (47 C), humid (40%) environment. Results indicate a marked reduction in the rate of increase of physiological body functions. Rectal temperature, weight loss, heart rate, and strain indices are all reduced to approximately 50% of uncooled levels. The cooling liner removed from 10% to 30% of total metabolic heat produced. This study also demonstrated the technical feasilibity of using a cooling liner in conjunction with a standard hard helmet. Potential applications of the cooling liner in thermally stressful environments are numerous, notably for helicopter and other aircrews.

A cross-sectional observational study of helmet use among motorcyclists in Wa, Ghana.

Science.gov (United States)

Akaateba, Millicent Awialie; Amoh-Gyimah, Richard; Yakubu, Ibrahim

2014-03-01

Motorcyclists' injuries and fatalities are a major public health concern in many developing countries including Ghana. This study therefore aimed to investigate the prevalence of helmet use among motorcyclists in Wa, Ghana. The method used involved a cross-sectional roadside observation at 12 randomly selected sites within and outside the CBD of Wa. A total of 14,467 motorcyclists made up of 11,360 riders and 3107 pillion riders were observed during the study period. Most observed riders (86.5%) and pillion riders (61.7%) were males. The overall prevalence of helmet use among the observed motorcyclists was 36.9% (95% CI: 36.1-37.7). Helmet use for riders was 45.8% (95% CI: 44.8-46.7) whilst that for pillion riders was 3.7% (95 CI: 3.0-4.4). Based on logistic regression analysis, higher helmet wearing rates were found to be significantly associated with female gender, weekdays, morning periods and at locations within the CBD. Riders at locations outside the CBD were about 7 times less likely to wear a helmet than riders within the CBD (48.9% compared to 42.3%; χ(2)(1)=49.526; plegislation that mandates the use of helmets by both riders and pillion riders on all roads in Ghana, helmet use is generally low in Wa. This suggests that all stakeholders in road safety should jointly intensify education on helmet use and pursue rigorous enforcement on all road types especially at locations outside the CBD to improve helmet use in Wa. Copyright © 2013 Elsevier Ltd. All rights reserved.

Neck muscle strain when wearing helmet and NVG during acceleration on a trampoline.

Science.gov (United States)

Sovelius, Roope; Oksa, Juha; Rintala, Harri; Huhtala, Heini; Siitonen, Simo

2008-02-01

The helmet-mounted equipment worn by military pilots increases the weight of the helmet system and shifts its center of gravity, increasing the loads on neck structures, especially during acceleration. The aim of this study was to determine neck muscle strain with different head-loads during trampoline-induced G loads (0 to +4 G). Under three conditions [no helmet, helmet, helmet with night vision goggles (NVG)], 14 subjects performed trampoline exercises including basic, hand-and-knee, and back bouncing. EMG activity was measured for the sternocleidomastoid (SCM), cervical erector spinae (CES), trapezoid (TRA), and thoracic erector spinae (TES) muscles. Muscle strain was determined as a percentage of maximal voluntary contraction (%MVC). For the three exercises combined, the following significant changes were found: compared to control, the helmet increased muscle strain by 18%, 28%, and 18% in the SCM, CES, and TRA, respectively; NVG produced a further increase of 11% in the SCM and 6% in the CES. During back bouncing, the helmet increased muscle strain by 14% in the SCM and 19% in the CES, and NVG further increased this strain by 14% in the SCM. Hand-and-knee bouncing loaded extensors: the helmet caused increases of 46% in the CES and 29% in the TES, while NVG produced a further 13% increase in CES activation. Helmet weight alone had a large effect on muscular workload. The additional frontal weight of the NVG caused a further increase in the activity of cervical muscles that were already subjected to high strain.

Helmets or not? Use science correctly.

Science.gov (United States)

Trégouët, Paul

2015-08-01

In a recent article, Hooper and Spicer make several arguments against legislation that would mandate the use of bicycle helmets. While they present reasonable objections to the utilitarian as well as the justice defence of such legislation, their review of the empirical evidence contains inaccuracies, omissions and a bias in the selection of empirical data. While there are legitimate reasons to argue against mandating helmet legislation, these arguments should still be based on clinically and scientifically sound evidence. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

The influence of ski helmets on sound perception and sound localisation on the ski slope

Directory of Open Access Journals (Sweden)

Lana Ružić

2015-04-01

Full Text Available Objectives: The aim of the study was to investigate whether a ski helmet interferes with the sound localization and the time of sound perception in the frontal plane. Material and Methods: Twenty-three participants (age 30.7±10.2 were tested on the slope in 2 conditions, with and without wearing the ski helmet, by 6 different spatially distributed sound stimuli per each condition. Each of the subjects had to react when hearing the sound as soon as possible and to signalize the correct side of the sound arrival. Results: The results showed a significant difference in the ability to localize the specific ski sounds; 72.5±15.6% of correct answers without a helmet vs. 61.3±16.2% with a helmet (p < 0.01. However, the performance on this test did not depend on whether they were used to wearing a helmet (p = 0.89. In identifying the timing, at which the sound was firstly perceived, the results were also in favor of the subjects not wearing a helmet. The subjects reported hearing the ski sound clues at 73.4±5.56 m without a helmet vs. 60.29±6.34 m with a helmet (p < 0.001. In that case the results did depend on previously used helmets (p < 0.05, meaning that that regular usage of helmets might help to diminish the attenuation of the sound identification that occurs because of the helmets. Conclusions: Ski helmets might limit the ability of a skier to localize the direction of the sounds of danger and might interfere with the moment, in which the sound is firstly heard.

Achieving all-age helmet use compliance for snow sports: strategic use of education, legislation and enforcement.

Science.gov (United States)

Fenerty, Lynne; Heatley, Jennifer; Young, Julian; Thibault-Halman, Ginette; Kureshi, Nelofar; Bruce, Beth S; Walling, Simon; Clarke, David B

2016-06-01

Nova Scotia is the first jurisdiction in the world to mandate ski and snowboard helmet use for all ages at ski hills in the province. This study represents a longitudinal examination of the effects of social marketing, educational campaigns and the introduction of helmet legislation on all-age snow sport helmet use in Nova Scotia. A baseline observational study was conducted to establish the threshold of ski and snowboarding helmet use. Based on focus groups and interviews, a social marketing campaign was designed and implemented to address factors influencing helmet use. A prelegislation observational study assessed the effects of social marketing and educational promotion on helmet use. After all-age snow sport helmet legislation was enacted and enforced, a postlegislation observational study was conducted to determine helmet use prevalence. Baseline data revealed that 74% of skiers and snowboarders were using helmets, of which 80% were females and 70% were males. Helmet use was high in children (96%), but decreased with increasing age. Following educational and social marketing campaigns, overall helmet use increased to 90%. After helmet legislation was enacted, 100% compliance was observed at ski hills in Nova Scotia. Results from this study demonstrate that a multifaceted approach, including education, legislation and enforcement, was effective in achieving full helmet compliance among all ages of skiers and snowboarders. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Helmet-Induced Occipital Neuralgia in a Military Aviator.

Science.gov (United States)

Chalela, Julio A

2018-04-01

Headaches among military personnel are very common and headgear wear is a frequently identified culprit. Helmet wear may cause migrainous headaches, external compression headache, other primary cranial neuralgias, and occipital neuralgia. The clinical features and the response to treatment allow distinction between the different types of headaches. Headaches among aviators are particularly concerning as they may act as distractors while flying and the treatment options are often incompatible with flying status. A 24-yr-old door gunner presented with suboccipital pain associated with the wear of his helmet. He described the pain as a paroxysmal stabbing sensation coming in waves. The physical exam and history supported the diagnosis of primary occipital neuralgia. Systemic pharmacological options were discussed with the soldier, but rejected due to his need to remain in flying status. An occipital nerve block was performed with good clinical results, supporting the diagnosis of occipital neuralgia and allowing him to continue as mission qualified. Occipital neuralgia can be induced by helmet wear in military personnel. Occipital nerve block can be performed in the deployed setting, allowing the service member to remain mission capable and sparing him/her from systemic side effects.Chalela JA. Helmet-induced occipital neuralgia in a military aviator. Aerosp Med Hum Perform. 2018; 89(4):409-410.

An Analysis of Technology-Related Distracted Biking Behaviors and Helmet Use Among Cyclists in New York City.

Science.gov (United States)

Ethan, Danna; Basch, Corey H; Johnson, Glen D; Hammond, Rodney; Chow, Ching Man; Varsos, Victoria

2016-02-01

Bicycling is becoming an increasingly utilized mode of transportation in New York City. Technology-related distracted bicycling and helmet use are behaviors that can impact bike safety. The aims of this study were twofold: (1) to determine rates and types of technology-related distracted behaviors among bicyclists in the borough of Manhattan in New York City; and (2) to assess the rate of bicycle helmet use among these cyclists. Bicyclists in five popular riding areas in Manhattan were observed for a total of 50 h using a digital video camera during summer months in 2014. Videos were coded and enumerated for the total number and gender of cyclists, type of bicycle, number wearing headphones/earbuds and/or using a mobile phone, and whether the cyclist was wearing a helmet. Almost 25,000 cyclists were observed across the five selected locations (n = 24,861). Riders were almost four times more likely not to wear a helmet on rental bikes as compared with non-rentals (Citi Bike(®) OR 3.8; 95% CI 2.5, 5.9: other rental OR 3.8; 95% CI 3.0, 4.9). Significantly increased odds of not wearing a helmet were observed for females relative to males (OR 1.4; 95% CI 1.1, 1.8) across varied times and locations. Overall, rates of technology-related distraction were low, with headphone use being most prevalent. Males were more likely to wear headphones/earbuds (OR 2.0; 95% CI 1.4, 2.9), as were cyclists on Citi Bikes relative to other rental bikes (OR 2.2; 95% CI 1.3, 3.6). Findings from this study contribute to the growing literature on distracted biking and helmet use among bike share program riders and other cyclists and can inform policymakers and program planners aiming to improve bicycle safety in urban settings.

[Prevalence of helmet use in children and adolescents in Germany and preventable bicycle-related head injuries].

Science.gov (United States)

Gutsche, J; Hintzpeter, B; Neuhauser, H; Schlaud, M

2011-08-01

Head injuries are the main cause of death in bicycle-related accidents among children and adolescents. According to a Cochrane Review, the risk of head injury (OR 0.31; 95% CI 0.26-0.37) or brain injury (OR 0.31; 95% CI 0.23-0.42) decreases by 69% if a helmet is worn. This study presents the prevalence of helmet use in cycling children and adolescents in Germany and the proportion of head injuries that could be prevented by wearing helmets. The potential effects of increased helmet wearing rates on the population attributable risk percentage for head injuries (PAR%) are demonstrated. The prevalence of helmet use in children aged 3-17 years was analysed using data from the German Health Interview and Examination Survey for Children and Adolescents (KiGGS). The percentage of head injuries preventable by helmet use in this group is estimated by calculating PAR%. Prevalence rates of helmet use and odds ratios from a Cochrane Review about the effectiveness of bicycle helmets for the prevention of head injuries were used for analysis. The potential effect of increased helmet use is shown in 3 scenarios by means of differences of PAR% values in the most relevant age groups. The older the children, the less likely they are to wear a helmet: 89.5% (95% CI 88.0%-90.8%) of the 3- to 6-year-old children wear a helmet when cycling but only 11.0% (95% CI 9.3%-12.9%) of 14- to 17-year-old adolescents do. In the youngest group (3-6 years) 19% of bicycle-related head injuries are attributable to the non-use of helmets, but this proportion rises to 67% in the oldest group (14-17 years). The PAR% of head injuries associated with not wearing a helmet may be reduced by more than a third by increasing the helmet wearing rate to 67% (2 out of 3) among adolescents, and may be reduced to half if 75% of adolescents wore a helmet. Particularly older children and adolescents hardly use bicycle helmets, hence the rate of preventable head injury is high. Efforts towards increasing helmet use

A Thermal Test System for Helmet Cooling Studies

Directory of Open Access Journals (Sweden)

Shaun Fitzgerald

2018-02-01

Full Text Available One of the primary causes of discomfort to both irregular and elite cyclists is heat entrapment by a helmet resulting in overheating and excessive sweating of the head. To accurately assess the cooling effectiveness of bicycle helmets, a heated plastic thermal headform has been developed. The construction consists of a 3D-printed headform of low thermal conductivity with an internal layer of high thermal mass that is heated to a constant uniform temperature by an electrical heating element. Testing is conducted in a wind tunnel where the heater power remains constant and the resulting surface temperature distribution is directly measured by 36 K-type thermocouples embedded within the surface of the head in conjunction with a thermal imaging camera. Using this new test system, four bicycle helmets were studied in order to measure their cooling abilities and to identify ‘hot spots’ where cooling performance is poor.

Evaluation of a promotional strategy to increase bicycle helmet use by children.

Science.gov (United States)

Parkin, P C; Spence, L J; Hu, X; Kranz, K E; Shortt, L G; Wesson, D E

1993-04-01

Bicycle-related head injuries are an important cause of death and disability, despite the availability of helmets. The objective of this study was to evaluate the effectiveness of a school-based bicycle helmet promotion program in increasing helmet use by children while controlling for secular trends. Two high-income and two low-income schools in an urban Canadian community were selected to receive a bicycle helmet promotion intervention, with the remaining 18 schools serving as controls. Approximately 1800 observations of bicycling children were made at randomly selected observational sites 2 to 5 months after the intervention to assess changes in behavior. Helmet use at all observation sites tripled from 3.4% (1990, preintervention) to 16% (1991, postintervention). In the high-income intervention area, observed helmet use rose dramatically from 4% to 36% in contrast to the more modest increase in the high-income control area from 4% to 15%. In the low-income intervention area, there was a modest increase from 1% to 7%, but it did not differ from the increase in the low-income control area from 3% to 13%. The program was highly successful in children of high-income families but not in children of low-income families. Developing strategies for low-income families remains a priority.

Does listening to music with an audio ski helmet impair reaction time to peripheral stimuli?

Science.gov (United States)

Ruedl, G; Pocecco, E; Wolf, M; Schöpf, S; Burtscher, M; Kopp, M

2012-12-01

With the recent worldwide increase in ski helmet use, new market trends are developing, including audio helmets for listening to music while skiing or snowboarding. The aim of this study was to evaluate whether listening to music with an audio ski helmet impairs reaction time to peripheral stimuli. A within-subjects design study using the Compensatory-Tracking-Test was performed on 65 subjects (36 males and 29 females) who had a mean age of 23.3 ± 3.9 years. Using repeated measures analysis of variance, we found significant differences in reaction times between the 4 test conditions (p=0.039). The lowest mean reaction time (± SE) was measured for helmet use while listening to music (507.9 ± 13.2 ms), which was not different from helmet use alone (514.6 ± 12.5 ms) (p=0.528). However, compared to helmet use while listening to music, reaction time was significantly longer for helmet and ski goggles used together (535.8 ± 14.2 ms, p=0.005), with a similar trend for helmet and ski goggles used together while listening to music (526.9 ± 13.8 ms) (p=0.094). In conclusion, listening to music with an audio ski helmet did not increase mean reaction time to peripheral stimuli in a laboratory setting. © Georg Thieme Verlag KG Stuttgart · New York.

Face mask removal is safer than helmet removal for emergent airway access in American football.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Beltz, Nora M; Day, Molly A; Decoster, Laura C

2014-06-01

In cases of possible cervical spine injury, medical professionals must be prepared to achieve rapid airway access while concurrently restricting cervical spine motion. Face mask removal (FMR), rather than helmet removal (HR), is recommended to achieve this. However, no studies have been reported that compare FMR directly with HR. The purpose of this study was to compare motion, time, and perceived difficulty in two commonly used American football helmets between FMR and HR techniques, and when helmet air bladders were deflated before HR compared with inflated scenarios. The study incorporated a repeated measures design and was performed in a controlled laboratory setting. Participants included 22 certified athletic trainers (15 men and seven women; mean age, 33.9±10.5 years; mean experience, 11.4±10.0 years; mean height, 172±9.4 cm; mean mass, 76.7±14.9 kg). All participants were free from upper extremity or central nervous system pathology for 6 months and provided informed consent. Dependent variables included head excursion in degrees (computed by subtracting the minimum position from the maximum position) in each of the three planes (sagittal, frontal, transverse), time to complete the required task, and ratings of perceived exertion. To address our study purposes, we used two-by-two repeated-measures analysis of variance (removal technique×helmet type, helmet type×deflation status) for each dependent variable. Independent variables consisted of removal technique (FMR and HR), helmet type (Riddell Revolution IQ [RIQ] and VSR4), and helmet deflation status (deflated [D], inflated, [I]). After familiarization, participants conducted two successful trials for each of six conditions in random order (RIQ-FMR, VSR4-FMR, RIQ-HR-D, VSR4-HR-D, RIQ-HR-I, and VSR4-HR-I). Face masks, helmets, and shoulder pads were removed from a live model wearing a properly fitted helmet and shoulder pads. The participant and an investigator stabilized the model's head. A six

Head and face injuries and helmet use among injured motorcyclists with road accidents in Isfahan, Iran

Directory of Open Access Journals (Sweden)

Azam Dadkhah

2015-10-01

Full Text Available BACKGROUND AND AIM: The study aimed to assess the frequency of head and face injuries in motorcyclists who had an accident and to find out the relationship between helmet use and frequency of these injuries. METHODS: A cross-sectional study with multi-stage sampling method provides data on the injured motorcyclists with road accidents. Data came from a registration form which has documented information of each injured person who had a road accident and hospitalized in the biggest hospital of Isfahan University of Medical Sciences, Iran (Al-Zahra. All the registration forms were surveyed for hospitalization period, treatment costs, severity of injury, and date of accident during 2010 (n = 1626. Later, among the list of injured motorcyclists during the last 3 months of the registration form, 125 cases were randomly selected and interviewed by phone regarding occurrence of the head and face injuries and whether wearing helmet during the accident. Confidence intervals (CI, Chi-square, and Phi and Cramer’s correlation coefficient were applied. The ethical approval was provided. RESULTS: Accident by motorcycle was 31.0% of all road accidents. The frequency of motorcycle accidents was higher in the autumn and among 21-25 year olds. The mean period of hospitalization was 4.3 days and the mean of hospital costs was about 9000000 Rials [about 8200 United States dollar (USD, in 2010]. Of motorcyclist, 35.0% reported they were helmeted when they had the accident. The frequency of head and face injuries was 51.0% among all the injured motorcyclists, 22.0% and 78.0% among the helmeted and non-helmeted motorcyclists, respectively (P = 0.009, r = -0.267. CONCLUSION: Motorcycle accidents comprise a large number of road accidents and cause substantial morbidity and financial impact for the community members. Head and face injuries are the most common trauma in motorcyclists, and the injury rate is higher among non-helmeted motorcyclists.

Acceleration-based methodology to assess the blast mitigation performance of explosive ordnance disposal helmets

Science.gov (United States)

Dionne, J. P.; Levine, J.; Makris, A.

2018-01-01

To design the next generation of blast mitigation helmets that offer increasing levels of protection against explosive devices, manufacturers must be able to rely on appropriate test methodologies and human surrogates that will differentiate the performance level of various helmet solutions and ensure user safety. Ideally, such test methodologies and associated injury thresholds should be based on widely accepted injury criteria relevant within the context of blast. Unfortunately, even though significant research has taken place over the last decade in the area of blast neurotrauma, there currently exists no agreement in terms of injury mechanisms for blast-induced traumatic brain injury. In absence of such widely accepted test methods and injury criteria, the current study presents a specific blast test methodology focusing on explosive ordnance disposal protective equipment, involving the readily available Hybrid III mannequin, initially developed for the automotive industry. The unlikely applicability of the associated brain injury criteria (based on both linear and rotational head acceleration) is discussed in the context of blast. Test results encompassing a large number of blast configurations and personal protective equipment are presented, emphasizing the possibility to develop useful correlations between blast parameters, such as the scaled distance, and mannequin engineering measurements (head acceleration). Suggestions are put forward for a practical standardized blast testing methodology taking into account limitations in the applicability of acceleration-based injury criteria as well as the inherent variability in blast testing results.

Noise exposure is increased with neonatal helmet CPAP in comparison with conventional nasal CPAP.

Science.gov (United States)

Trevisanuto, D; Camiletti, L; Doglioni, N; Cavallin, F; Udilano, A; Zanardo, V

2011-01-01

in adults, noninvasive ventilation via a helmet is associated with significantly greater noise than nasal and facial masks. We hypothesized that noise exposure could be increased with neonatal helmet continuous positive airway pressure (CPAP) in comparison with conventional nasal CPAP (nCPAP). Our primary objective was to compare the noise intensity produced by a neonatal helmet CPAP and a conventional nCPAP system. Furthermore, we aimed to evaluate the effect of the gas flow rate and the presence of the humidifier and the filter on noise levels during neonatal helmet CPAP treatment. in this bench study, noise intensity was measured in the following settings: helmet CPAP, nCPAP, incubator and the neonatal intensive care unit. In helmet CPAP, noise measurements were performed at different gas flow rates (8, 10 and 12 l/min), while in nCPAP, the flow rate was 8 l/min. For both CPAP systems, the level of pressure was maintained constant at 5 cmH(2) O. during neonatal helmet CPAP, the median (interquartile range) noise levels were significantly higher than those during nCPAP: 70.0 dB (69.9-70.4) vs. 62.7 dB (62.5-63.0); PCPAP, the noise intensities changed with increasing flow rate and with the presence of a humidifier or a filter. noise intensities generated by the neonatal helmet CPAP were significantly higher than those registered while using a conventional nCPAP system. In the helmet, the noise intensity depends on the gas flow rate, and the presence of a humidifier and a filter in the system. 2010 The Acta Anaesthesiologica Scandinavica Foundation.

Head position in the MEG helmet affects the sensitivity to anterior sources.

Science.gov (United States)

Marinkovic, K; Cox, B; Reid, K; Halgren, E

2004-11-30

Current MEG instruments derive the whole-head coverage by utilizing a helmet-shaped opening at the bottom of the dewar. These helmets, however, are quite a bit larger than most people's heads so subjects commonly lean against the back wall of the helmet in order to maintain a steady position. In such cases the anterior brain sources may be too distant to be picked up by the sensors reliably. Potential "invisibility" of the frontal and anterior temporal sources may be particularly troublesome for the studies of cognition and language, as they are subserved significantly by these areas. We examined the sensitivity of the distributed anatomically-constrained MEG (aMEG) approach to the head position ("front" vs. "back") secured within a helmet with custom-tailored bite-bars during a lexical decision task. The anterior head position indeed resulted in much greater sensitivity to language-related activity in frontal and anterior temporal locations. These results emphasize the need to adjust the head position in the helmet in order to maximize the "visibility" of the sources in the anterior brain regions in cognitive and language tasks.

North Caucasian helmets from the Crimean Tatar Nobility from the Museum of Topkapi Palace (Istanbul, Turkey. Design Features, Design and Combat Use

Directory of Open Access Journals (Sweden)

Leonid A. Bobrov

2016-06-01

Full Text Available The article describes the helmets of the Crimean Tatar nobility stored in the Museum of Topkapi Palace (Istanbul, Republic of Turkey. Based on the analysis of design and system design determined that hats were made of Circassian masters of the XVIII century. Helmet No. 1/810 in shape of the dome relates to the type of bevel. Forged a gilded crown complemented by ornamented Hoop, pads, conical pommel, and ringed barmitsa Persian type. In Cherkessia similar hats were known as Tang (from the Arab. "the Taj", i.e. "crown". It is most likely that the owner of the helmet was the last Noureddine Crimean khanate, Bahadir Giray (1789-1792 was the son of MuminGirei (?-1747 and grandson of Khan Saadet Giray IV (1717-1724. Helmet No. 1/812по the shape of a dome refers to the type of conal. Forged iron gilded crown complemented by ornamented Hoop, plates and funnel-shaped topping. Dome placed on the manufacture date of the helmet – "1180 of the Hijra" (i.e., 1766-1767 in the Gregorian calendar, as well as the inscription: "Owner Sultan Ali", "Muhammad Giray", "Mansour". Helmet No. 1/811по the shape of a dome refers to the type of cylindrical. Faceted iron supplemented gilt crown ornamented Hoop, conical pommel and Aventail Persian type. On the front of hats placed the inscription, "Sultan Mohammed Ibn AdilGiray". This suggests that the owner of the helmet could be the son of Nureddin (1718, serasker Budjaka and Editcol (1727-1728 Adil Ibn Selim I Giray or seraskier EditcolAdil Ibn Selim III Giray (1766-1767. In the framework of the interdisciplinary research were made copies of these helmets, which have become the object of scientific experiments aimed at the study of the functional properties of the considered hats. According to the results of the experimental tests it was found that all three of the helmet provide very reliable protection of the head and neck of the warrior from the cutting and cut-and-cutting blows of the enemy. The saber blade

Clinical review: Helmet and non-invasive mechanical ventilation in critically ill patients.

Science.gov (United States)

Esquinas Rodriguez, Antonio M; Papadakos, Peter J; Carron, Michele; Cosentini, Roberto; Chiumello, Davide

2013-04-25

Non-invasive mechanical ventilation (NIV) has proved to be an excellent technique in selected critically ill patients with different forms of acute respiratory failure. However, NIV can fail on account of the severity of the disease and technical problems, particularly at the interface. The helmet could be an alternative interface compared to face mask to improve NIV success. We performed a clinical review to investigate the main physiological and clinical studies assessing the efficacy and related issues of NIV delivered with a helmet. A computerized search strategy of MEDLINE/PubMed (January 2000 to May 2012) and EMBASE (January 2000 to May 2012) was conducted limiting the search to retrospective, prospective, nonrandomized and randomized trials. We analyzed 152 studies from which 33 were selected, 12 physiological and 21 clinical (879 patients). The physiological studies showed that NIV with helmet could predispose to CO₂ rebreathing and increase the patients' ventilator asynchrony. The main indications for NIV were acute cardiogenic pulmonary edema, hypoxemic acute respiratory failure (community-acquired pneumonia, postoperative and immunocompromised patients) and hypercapnic acute respiratory failure. In 9 of the 21 studies the helmet was compared to a face mask during either continous positive airway pressure or pressure support ventilation. In eight studies oxygenation was similar in the two groups, while the intubation rate was similar in four and lower in three studies for the helmet group compared to face mask group. The outcome was similar in six studies. The tolerance was better with the helmet in six of the studies. Although these data are limited, NIV delivered by helmet could be a safe alternative to the face mask in patients with acute respiratory failure.

A Discussion of the Issue of Football Helmet Removal in Suspected Cervical Spine Injuries

Science.gov (United States)

Segan, Ross D.; Cassidy, Christine; Bentkowski, Jamie

1993-01-01

In some areas, it is a commonly accepted emergency medical technician protocol to remove a helmet during the initial management of suspected cervical spine injures. After a comprehensive survey of relevant literature, four primary reasons why Emergency Medical Services professionals would desire to remove a helmet emerge. Sources suggest that the presence of a helmet might: 1) interfere with immobilization of the athlete; 2) interfere with the ability to visualize injuries; 3) cause hyperflexion of the cervical spine; and 4) prevent proper airway management during a cardiorespiratory emergency. Many available protocols are designed for the removal of closed chamber motorcycle helmets that do not have removable face masks. There are a great number of differing viewpoints regarding this issue. The varying viewpoints are results of the failure of many emergency medical technician management protocols to address the unique situation presented by a football helmet. We: 1) demonstrate that football helmet removal is potentially dangerous and unnecessary, 2) suggest that cardiorespiratory emergencies can be effectively managed without removing the helmet, and 3) provide sports medicine professional with information that may be used to establish a joint Emergency Medical Services/Sports Medicine emergency action plan. ImagesFig. 1.Fig 2.Fig 3.Fig 4.Fig 5.Fig 6. PMID:16558244

40° image intensifier tubes in an integrated helmet system

Science.gov (United States)

Schreyer, Herbert; Boehm, Hans-Dieter V.; Svedevall, B.

1993-12-01

EUROCOPTER has been under contract to the French and German ministries of defence for five years to develop the TIGER, a second generation anti-tank helicopter. A piloting thermal imager has been installed on a steerable platform in the helicopter nose in order to achieve the possibility of flying round the clock. In addition to this sensor, which is sensitive at a wavelength of 10 micrometers , the German side has proposed using an Integrated Helmet System in the PAH 2. This helmet, manufactured by GEC-Marconi Avionics, incorporates two cathode ray tubes (CRT) and two image intensifier tubes which allow the pilot to use an additional sensor in the visible and near infrared spectrum. The electronic part will be built by Teldix. EUROCOPTER DEUTSCHLAND has received the first demonstrator of this helmet for testing in the EUROCOPTER Visionics Laboratory. Later, the C-prototype will be integrated into a BK 117 helicopter (AVT Avionik Versuchstrager). This new helmet has a field of view of 40 degree(s), and exit pupil of 15 mm and improved possibilities of adjusting the optical part. Laboratory tests have been carried out to test important parameters like optical resolution under low light level conditions, field of view, eye relief or exit pupil. The CRT channels have been tested for resolution, distortion, vignetting and homogeneity. The requirements and the properties of the helmet, test procedures and the results of these tests are presented in the paper.

Prevalence and determinants of non-standard motorcycle safety helmets amongst food delivery workers in Selangor and Kuala Lumpur.

Science.gov (United States)

Kulanthayan, S; See, Lai Git; Kaviyarasu, Y; Nor Afiah, M Z

2012-05-01

Almost half of the global traffic crashes involve vulnerable groups such as pedestrian, cyclists and two-wheeler users. The main objective of this study was to determine the factors that influence standard of the safety helmets used amongst food delivery workers by presence of Standard and Industrial Research Institute of Malaysia (SIRIM) certification label. A cross sectional study was conducted amongst 150 food delivery workers from fast food outlets in the vicinity of Selangor and Kuala Lumpur. During observation, safety helmets were classified as standard safety helmet in the presence of SIRIM label and non-standard in the absence of the label. They were approached for questionnaire participation once consent was obtained and were requested to exchange their safety helmet voluntarily with a new one after the interview. Data analysis was carried out using SPSS. Chi square and logistic regression analysis was applied to determine the significance and odds ratio of the variables studied, respectively (penetration test, age, education level, knowledge, crash history, types of safety helmet, marital status and years of riding experience) against the presence of SIRIM label. The response rate for this study was 85.2%. The prevalence of non-standard helmets use amongst fast food delivery workers was 55.3%. Safety helmets that failed the penetration test had higher odds of being non-standard helmets compared with safety helmets passing the test. Types of safety helmet indicated half-shell safety helmets had higher odds to be non-standard safety helmets compared to full-shell safety helmets. Riders with more years of riding experience were in high odds of wearing non-standard safety helmets compared to riders with less riding experience. Non-standard (non-SIRIM approved) helmets were more likely to be half-shell helmets, were more likely to fail the standards penetration test, and were more likely to be worn by older, more experienced riders. The implications of these

Impact of mandatory motorcycle helmet wearing legislation on head injuries in Viet Nam: results of a preliminary analysis.

Science.gov (United States)

Passmore, Jonathon; Tu, Nguyen Thi Hong; Luong, Mai Anh; Chinh, Nguyen Duc; Nam, Nguyen Phuong

2010-04-01

To compare estimated prevalence of head injuries among road traffic injury patients admitted to hospitals, before and after the introduction of a mandatory helmet law in the Socialist Republic of Viet Nam. Before and after study of all road traffic injury patients with head injuries admitted to 20 provincial and central hospitals 3 months before and after the new law came into effect on 15 December 2007. Relative risk was computed and comparison made for the periods of 3 months before and after the new law. The study found a 16 percent reduction in the risk of road traffic head injuries (4683 to 3522; relative risk [RR] 0.84; 95% confidence interval [CI] 0.81-0.87) and an 18 percent reduction in the risk of road traffic death (deaths in hospital plus injured patients discharged to die at home; 566 to 417; RR 0.82; 95% CI 0.73-0.93). Over the first 3 months of the comprehensive mandatory helmet legislation there has been a significant reduction in the risk of road traffic head injuries among patients admitted to 20 hospitals. The Viet Nam Government's decision to require all motorcycle riders and passengers to wear helmets is suspected of leading to positive road safety benefits and should be seen as a policy example for other low- and middle-income countries with a high utilization of motorcycles for transport.

Changes in motorcycle-related injuries and deaths after mandatory motorcycle helmet law in a district of Vietnam.

Science.gov (United States)

Ha, Ninh Thi; Ederer, David; Vo, Van Anh Ha; Pham, An Van; Mounts, Anthony; Nolen, Leisha D; Sugerman, David

2018-01-02

Our study measured the change in head injuries and deaths among motorcycle users in Cu Chi district, a suburban district of Ho Chi Minh City. Hospital records for road traffic injuries (RTIs) were collected from the Cu Chi Trauma Centre and motorcycle-related death records were obtained from mortality registries in commune health offices. Head injury severity was categorized using the Abbreviated Injury Score (AIS). Rate ratios (RRs) were used to compare rates pre- and post-law (2005/2006-2009/2010). Cu Chi's population, stratified by year, age, and sex, was used as the denominator. Of records identifying the transportation mode at the time of injury, motorcyclists accounted for most injuries (3,035, 87%) and deaths (238, 90%). Head injuries accounted for 70% of motorcycle-related hospitalizations. Helmet use was not recorded in any death records and not in 97% of medical records. Males accounted for most injuries (73%) and deaths (88%). The median age was 28 years and 32 years for injuries and deaths, respectively. Compared to the pre-law period, rates of motorcycle injuries (RR = 0.53; 95% confidence interval [CI], 0.49-0.58), head injuries (RR = 0.35; 95% CI, 0.31-0.39), severe head injuries (RR = 0.47; 95% CI, 0.34-0.63), and deaths (RR = 0.69; 95% CI, 0.53-0.89) significantly decreased in the post-law period. Rates of head injuries and deaths among motorcycle riders decreased significantly after implementation of the mandatory helmet law in Vietnam. To further examine the impact of the motorcycle helmet law, including compliance and helmet quality, further emphasis should be placed on gathering helmet use data from injured motorcyclists.

The Theory of Planned Behavior and Helmet Use among College Students

Science.gov (United States)

Ross, Lisa Thomson; Ross, Thomas P.; Farber, Sarah; Davidson, Caroline; Trevino, Meredith; Hawkins, Ashley

2011-01-01

Objectives: To assess undergraduate helmet use attitudes and behaviors in accordance with the theory of planned behavior (TPB). We predicted helmet wearers and nonwearers would differ on our subscales. Methods: Participants (N = 414, 69% female, 84% white) completed a survey. Results: Principal component analysis and reliability analysis guided…

Comparative Outcomes of Traumatic Brain Injury from Biking Accidents With or Without Helmet Use.

Science.gov (United States)

Dagher, Jehane H; Costa, Camille; Lamoureux, Julie; de Guise, Elaine; Feyz, Mitra

2016-01-01

To determine if health outcomes and demographics differ according to helmet status between persons with cycling-related traumatic brain injuries (TBI). This is a retrospective study of 128 patients admitted to the Montreal General Hospital following a TBI that occurred while cycling from 2007-2011. Information was collected from the Quebec trauma registry and the coroner's office in cases of death from cycling accidents. The independent variables collected were socio-demographic, helmet status, clinical and neurological patient information. The dependent variables evaluated were length of stay (LOS), extended Glasgow outcome scale (GOS-E), injury severity scale (ISS), discharge destination and death. 25% of cyclists wore a helmet. The helmet group was older, more likely to be university educated, married and retired. Unemployment, longer intensive care unit (ICU) stay, severe intracranial bleeding and neurosurgical interventions were more common in the no helmet group. There was no significant association between the severity of the TBI, ISS scores, GOS-E or death and helmet wearing. The median age of the subjects who died was higher than those who survived. Cyclists without helmets were younger, less educated, single and unemployed. They had more severe TBIs on imaging, longer LOS in ICU and more neurosurgical interventions. Elderly cyclists admitted to the hospital appear to be at higher risk of dying in the event of a TBI.

29 CFR 1915.155 - Head protection.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Head protection. 1915.155 Section 1915.155 Labor... helmets. (1) Head protection must comply with any of the following consensus standards: (i) ANSI Z89.1... as head protection devices that are constructed in accordance with one of the above consensus...

Rates of motorcycle helmet use and reasons for non-use among adults and children in Luang Prabang, Lao People's Democratic Republic.

Science.gov (United States)

Fong, Michelle C; Measelle, Jeffrey R; Dwyer, Jessica L; Taylor, Yvonne K; Mobasser, Arian; Strong, Theresa M; Werner, Susanne; Ouansavanh, Siamphone; Mounmingkham, Amphone; Kasuavang, Mai; Sittiphone, Dalika; Phoumesy, Khamhak; Sysaythong, Keo; Khantysavath, Khauphan; Bounnaphone, Somchit; Vilaysom, Amphone; Touvachao, Sengchanh; Mounmeuangxam, Siviengxam; Souralay, Somchittana; Lianosay, Baoher; Lia, Thongher; Spector, Jonathan M

2015-09-28

Motorcycles make up 81 % of the total vehicle population and 74 % of road traffic deaths in Lao PDR. Helmets reduce the risk and severity of injuries resulting from motorcycle accidents by 72 %. Although Lao law mandates motorcycle helmet use among drivers and passengers, the prevalence of helmet use in Luang Prabang, Lao PDR is unknown. This project aimed to measure the prevalence of motorcycle helmet use among riders (i.e., drivers and passengers) in Luang Prabang. An observational survey in Luang Prabang was conducted in February 2015 to measure the prevalence of motorcycle helmet use among drivers and passengers. Additionally, non-helmet wearing riders were surveyed to identify the reasons for helmet non-use. Of 1632 motorcycle riders observed, only 16.2 % wore helmets. Approximately 29 % of adults wore helmets while less than 1 % of all children wore helmets. When surveyed about attitudes towards helmet use, the majority of adult drivers indicated that they did not like how adult helmets feel or made them look. Additionally, almost half of motorcyclists who did not own child helmets reported that their child was too young to wear a helmet. Our finding that children wear helmets at significantly lower rates compared to adults is consistent with findings from neighboring countries in Southeast Asia. Results of this study have implications for public health campaigns targeting helmet use, especially among children.

Maintaining neutral sagittal cervical alignment after football helmet removal during emergency spine injury management.

Science.gov (United States)

Decoster, Laura C; Burns, Matthew F; Swartz, Erik E; Murthi, Dinakar S; Hernandez, Adam E; Vailas, James C; Isham, Linda L

2012-04-15

Descriptive laboratory study. To determine whether the placement of padding beneath the occiput after helmet removal is an effective intervention to maintain neutral sagittal cervical spine alignment in a position comparable with the helmeted condition. Current on-field recommendations for managing football athletes with suspected cervical spine injuries call for face mask removal, rather than helmet removal, because the combination of helmet and shoulder pads has been shown to maintain neutral cervical alignment. Therefore, in cases when helmet removal is required, recommendations also call for shoulder pad removal. Because removal of equipment causes motion, any technique that postpones the need to remove the shoulder pads would reduce prehospital motion. Four lateral radiographs of 20 male participants were obtained (age = 23.6 ± 2.7 years). Radiographs of participants wearing shoulder pads and helmet were first obtained. The helmet was removed and radiographs of participants with occipital padding were obtained immediately and 20 minutes later and finally without occipital padding. Cobb angle measurements for C2-C6 vertebral segments were determined by an orthopedic spine surgeon blinded to the study's purpose. Intraobserver reliability was determined using intraclass coefficient analysis. Measurements were analyzed using a 1×4 repeated-measures analysis of variance and post hoc pairwise comparisons with Bonferroni correction. Intraobserver analysis showed excellent reliability (intraclass correlation = 1.0; 95% confidence interval [CI], 0.999-1.0). Repeated-measures analysis of variance detected significant differences (F(3,17) = 13.34; P football helmet in the field, occipital padding (along with full body/head immobilization techniques) may be used to limit cervical lordosis, allowing safe delay of shoulder pad removal.

Experimental investigations on the cooling of a motorcycle helmet with phase change material (PCM

Directory of Open Access Journals (Sweden)

Fok S.C.

2011-01-01

Full Text Available The thermal comfort of motorcycle helmet during hot weather is important as it can affect the physiological and psychological condition of the rider. This paper examines the use of phase change material (PCM to cool a motorcycle helmet and presents the experimental investigations on the influences of the simulated solar radiation, wind speed, and heat generation rate on the cooling system. The result shows that the PCM-cooled helmet is able to prolong the thermal comfort period compared to a normal helmet. The findings also indicate that the heat generation from the head is the predominant factor that will affect the PCM melting time. Simulated solar radiation and ram-air due to vehicle motion under adiabatic condition can have very little influences on the PCM melting time. The results suggested that the helmet usage time would be influenced by the amount of heat generated from the head. Some major design considerations based on these findings have been included. Although this investigation focuses on the cooling of a motorcyclist helmet, the findings would also be useful for the development of PCM-cooling systems in other applications.

Investigation of the reasons for not using helmet among motorcyclists in Kerman, Iran.

Science.gov (United States)

Maghsoudi, Aliasghar; Boostani, Dariush; Rafeiee, Manoochehr

2018-03-01

This study was carried out to investigate reasoning and interpretation of motorcyclists for not using helmet utilizing qualitative methodology of 'grounded theory'. The field of the study was Kerman, a cultural-historical city at the south-east of Iran. Participants were 21 young male motorcyclists. Two sampling strategies were used: maximum variation and snowball sampling. To collect data, in-depth, open-ended interviews were conducted. Data analysis yielded seven categories: fatalism; a barrier to social relationships; peer group pressure and negative labelling; messing up the appearance; disturbance in hearing and vision; barrier to normal breathing; and heaviness and superfluity of helmet. Based on the findings of the current study, it could be concluded that socio-cultural contexts, motorcyclists' worldview and partly helmet-related problems are of the main factors which affect motorcycling. Therefore, the studies, policy-makings, and intervening programmes to control injury and to promote safety among motorcyclists should be focused on socio-cultural barriers to helmet use in general and changing the motorcyclists' standpoints toward fatalism in particular. Helmet-related problems should be considered, too.

Aerodynamic study of time-trial helmets in cycling racing using CFD analysis.

Science.gov (United States)

Beaumont, F; Taiar, R; Polidori, G; Trenchard, H; Grappe, F

2018-01-23

The aerodynamic drag of three different time-trial cycling helmets was analyzed numerically for two different cyclist head positions. Computational Fluid Dynamics (CFD) methods were used to investigate the detailed airflow patterns around the cyclist for a constant velocity of 15 m/s without wind. The CFD simulations have focused on the aerodynamic drag effects in terms of wall shear stress maps and pressure coefficient distributions on the cyclist/helmet system. For a given head position, the helmet shape, by itself, obtained a weak effect on a cyclist's aerodynamic performance (CFD results have also shown that both helmet shape and head position significantly influence drag forces, pressure and wall shear stress distributions on the whole cyclist's body due to the change in the near-wake behavior and in location of corresponding separation and attachment areas around the cyclist. Copyright © 2017 Elsevier Ltd. All rights reserved.

Astronauts Parise and Jernigan check helmets prior to training session

Science.gov (United States)

1994-01-01

Attired in training versions of the Shuttle partial-pressure launch and entry suits, payload specialist Dr. Ronald A Parise (left) and astronaut Tamara E. Jernigan, payload commander, check over their helmets prior to a training session. Holding the helmets is suit expert Alan M. Rochford, of NASA. The two were about to join their crew mates in a session of emergency bailout training at JSC's Weightless Environment Training Facility (WETF).

Methods of estimating the effect of integral motorcycle helmets on physiological and psychological performance.

Science.gov (United States)

Bogdan, Anna; Sudoł-Szopińska, Iwona; Luczak, Anna; Konarska, Maria; Pietrowski, Piotr

2012-01-01

This article proposes a method for a comprehensive assessment of the effect of integral motorcycle helmets on physiological and cognitive responses of motorcyclists. To verify the reliability of commonly used tests, we conducted experiments with 5 motorcyclists. We recorded changes in physiological parameters (heart rate, local skin temperature, core temperature, air temperature, relative humidity in the space between the helmet and the surface of the head, and the concentration of O(2) and CO(2) under the helmet) and in psychological parameters (motorcyclists' reflexes, fatigue, perceptiveness and mood). We also studied changes in the motorcyclists' subjective sensation of thermal comfort. The results made it possible to identify reliable parameters for assessing the effect of integral helmets on performance, i.e., physiological factors (head skin temperature, internal temperature and concentration of O(2) and CO(2) under the helmet) and on psychomotor factors (reaction time, attention and vigilance, work performance, concentration and a subjective feeling of mood and fatigue).

Facial asymmetry correction with moulded helmet therapy in infants with deformational skull base plagiocephaly.

Science.gov (United States)

Kreutz, Matthias; Fitze, Brigitte; Blecher, Christoph; Marcello, Augello; Simon, Ruben; Cremer, Rebecca; Zeilhofer, Hans-Florian; Kunz, Christoph; Mayr, Johannes

2018-01-01

The recommendation issued by the American Academy of Pediatrics in the early 1990s to position infants on their back during sleep to prevent sudden infant death syndrome (SIDS) has dramatically reduced the number of deaths due to SIDS but has also markedly increased the prevalence of positional skull deformation in infants. Deformation of the base of the skull occurs predominantly in very severe deformational plagiocephaly and is accompanied by facial asymmetry, as well as an altered ear position, called ear shift. Moulded helmet therapy has become an accepted treatment strategy for infants with deformational plagiocephaly. The aim of this study was to determine whether facial asymmetry could be corrected by moulded helmet therapy. In this retrospective, single-centre study, we analysed facial asymmetry of 71 infants with severe deformational plagiocephaly with or without deformational brachycephaly who were undergoing moulded helmet therapy between 2009 and 2013. Computer-assisted, three-dimensional, soft-tissue photographic scanning was used to record the head shape before and after moulded helmet therapy. The distance between two landmarks in the midline of the face (i.e., root of the nose and nasal septum) and the right and left tragus were measured on computer-generated indirect and objective 3D photogrammetry images. A quotient was calculated between the two right- and left-sided distances to the midline. Quotients were compared before and after moulded helmet therapy. Infants without any therapy served as a control group. The median age of the infants before onset of moulded helmet therapy was 5 months (range 3-16 months). The median duration of moulded helmet therapy was 5 months (range 1-16 months). Comparison of the pre- and post-treatment quotients of the left vs. right distances measured between the tragus and root of the nose (n = 71) and nasal septum (n = 71) revealed a significant reduction of the asymmetry (Tragus-Nasion-Line Quotient: 0

Assessing women's lacrosse head impacts using finite element modelling.

Science.gov (United States)

Clark, J Michio; Hoshizaki, T Blaine; Gilchrist, Michael D

2018-04-01

Recently studies have assessed the ability of helmets to reduce peak linear and rotational acceleration for women's lacrosse head impacts. However, such measures have had low correlation with injury. Maximum principal strain interprets loading curves which provide better injury prediction than peak linear and rotational acceleration, especially in compliant situations which create low magnitude accelerations but long impact durations. The purpose of this study was to assess head and helmet impacts in women's lacrosse using finite element modelling. Linear and rotational acceleration loading curves from women's lacrosse impacts to a helmeted and an unhelmeted Hybrid III headform were input into the University College Dublin Brain Trauma Model. The finite element model was used to calculate maximum principal strain in the cerebrum. The results demonstrated for unhelmeted impacts, falls and ball impacts produce higher maximum principal strain values than stick and shoulder collisions. The strain values for falls and ball impacts were found to be within the range of concussion and traumatic brain injury. The results also showed that men's lacrosse helmets reduced maximum principal strain for follow-through slashing, falls and ball impacts. These findings are novel and demonstrate that for high risk events, maximum principal strain can be reduced by implementing the use of helmets if the rules of the sport do not effectively manage such situations. Copyright © 2018 Elsevier Ltd. All rights reserved.

A DESCRIPTIVE STUDY OF PATTERN OF FATAL HEAD INJURY IN HELMETED AND NONHELMETED VICTIMS OF TWO WHEELER ACCIDENTS

Directory of Open Access Journals (Sweden)

P. A. Sheeju

2016-07-01

Full Text Available BACKGROUND Motor vehicle crashes are a major cause of fatality all over the world. By 2020, motor vehicle injury is projected to become the third leading contributor to the global burden of disease in the world. Motor cyclists are about 25 times more likely than car occupants to die in Road Traffic Accidents. Data on the incidence and types of crashes is required to guide safety policy. Knowledge of how injuries are caused and of what type they are of valuable instrument for identifying interventions and monitoring the effectiveness of intervention. The present study was done to find out the factors that contribute for motor cycle crashes and to study the injury pattern seen in helmeted and non-helmeted victims. MATERIAL AND METHODS Victims of two wheeler accidents brought for autopsy in a Govt. Medical College were studied from October 2010 to August 2011. Two wheelers include motor cycles, scooters and mopeds. Bicycles were excluded from the study. Accidents include all types; against all types of vehicles running on the road, collision with any object, surface or any animal or fall from vehicle. The details of the accident were collected in a printed proforma from relative/witnesses and from police officials. The injuries were entered in the specific columns of proforma. Data was analysed with MS Excel. RESULTS Death due to head injury is more in non-helmeted (52.5% compared to helmeted drivers (43.8 % whereas injury to chest and abdomen and limbs are more in helmeted. Combination of injuries (Head+Chest+Abdomen predominated in helmeted drivers (18.8% compared to 5% in non-helmeted drivers. Spinal injuries were more in helmeted than in non-helmeted. CONCLUSION The pattern of head injury was analysed in detail in helmeted and non-helmeted drivers. This will help in detailing of pattern of head injury in both groups.

The Association Between Risk-taking Behavior and Helmet Use Among Motorcyclist

Science.gov (United States)

Trinh, Tu Anh; Phuong Linh Le, Thi

2018-04-01

The central aim of the research was to examine speeding behavior without helmet wearing among motorcycle riders in Ho Chi Minh City. The research model expanded the Theory of Planned Behavior by both psychological flow theory and sensation-seeking. 268 motorcyclists were involved in the research. A Confirmatory factor analysis and a Structural equation modeling were employed for model specification. The findings indicated a significant effect between predictors and the intention of speeding without helmet wearing. In addition, there was direct relation between intention and actual behavior. Also, sensation-seeking proved to be important in moderating predictors between the low-sensation-seeking motorcyclists and high-sensation-seeking ones. A deeper understanding of why motorcycle riders exceed the speed limit without wearing helmet played key role in changing their behavior.

[Comfort and noise level in infants with helmet interface].

Science.gov (United States)

Medina, A; Alvarez Fernández, P; Rey Galán, C; Álvarez Mendiola, P; Álvarez Blanco, S; Vivanco Allende, A

2015-10-01

To evaluate comfort and noise intensity using the COMFORT scale in infants who receive respiratory support with a helmet interface. An observational descriptive study was conducted on all infants (1 to 12 months of age) admitted to a PICU from November 1st 2013 to March 31st 2014 and who received non-invasive ventilation with a helmet interface. Tolerance to the interface was assessed by use of the COMFORT scale. The intensity of the noise to which the infants were exposed was measured with a TES1350A HIBOK 412 sound-level meter. Three measurements were made every day. Twenty seven patients with bronchiolitis (median age: 54 days; range: 10 to 256) were included. Median COMFORT score in the first day was 21 points (14 - 28). An increase in patient comfort was found with a gradual decrease in the scores, with a maximum reduction of 22% from the first hours (score of 22) to the fifth day (score of 18). The minimum sound intensity registered was 42dB, and the maximum was 78dB. Background noise intensity was associated with noise intensity in the helmet. No differences were observed in COMFORT score and noise intensity between ventilator devices. Helmet interface was well tolerated by infants. COMFORT score results are an indicator that infants were comfortable or very comfortable. The measured noise intensity was in the safe range permitted by World Health Organization. Copyright © 2014 Asociación Española de Pediatría. Published by Elsevier España, S.L.U. All rights reserved.

Automatic helmet-wearing detection for law enforcement using CCTV cameras

Science.gov (United States)

Wonghabut, P.; Kumphong, J.; Satiennam, T.; Ung-arunyawee, R.; Leelapatra, W.

2018-04-01

The objective of this research is to develop an application for enforcing helmet wearing using CCTV cameras. The developed application aims to help law enforcement by police, and eventually resulting in changing risk behaviours and consequently reducing the number of accidents and its severity. Conceptually, the application software implemented using C++ language and OpenCV library uses two different angle of view CCTV cameras. Video frames recorded by the wide-angle CCTV camera are used to detect motorcyclists. If any motorcyclist without helmet is found, then the zoomed (narrow-angle) CCTV is activated to capture image of the violating motorcyclist and the motorcycle license plate in real time. Captured images are managed by database implemented using MySQL for ticket issuing. The results show that the developed program is able to detect 81% of motorcyclists on various motorcycle types during daytime and night-time. The validation results reveal that the program achieves 74% accuracy in detecting the motorcyclist without helmet.

Practice type effects on head impact in collegiate football.

Science.gov (United States)

Reynolds, Bryson B; Patrie, James; Henry, Erich J; Goodkin, Howard P; Broshek, Donna K; Wintermark, Max; Druzgal, T Jason

2016-02-01

OBJECT IVE: This study directly compares the number and severity of subconcussive head impacts sustained during helmet-only practices, shell practices, full-pad practices, and competitive games in a National Collegiate Athletic Association (NCAA) Division I-A football team. The goal of the study was to determine whether subconcussive head impact in collegiate athletes varies with practice type, which is currently unregulated by the NCAA. Over an entire season, a cohort of 20 collegiate football players wore impact-sensing mastoid patches that measured the linear and rotational acceleration of all head impacts during a total of 890 athletic exposures. Data were analyzed to compare the number of head impacts, head impact burden, and average impact severity during helmet-only, shell, and full-pad practices, and games. Helmet-only, shell, and full-pad practices and games all significantly differed from each other (p ≤ 0.05) in the mean number of impacts for each event, with the number of impacts being greatest for games, then full-pad practices, then shell practices, and then helmet-only practices. The cumulative distributions for both linear and rotational acceleration differed between all event types (p football players.

Influence of humidification on comfort during noninvasive ventilation with a helmet.

Science.gov (United States)

Ueta, Kazuyoshi; Tomita, Toshiji; Uchiyama, Akinori; Ohta, Noriyuki; Iguchi, Naoya; Goto, Yukiko; Fujino, Yuji

2013-05-01

To evaluate optimal humidifier water temperature when using a helmet for noninvasive ventilation. Twenty-eight healthy individuals underwent 8 cm H2O CPAP ventilation with FIO2 of 0.21 and 0.5. Each was sequentially tested in the following order: using the helmet without humidification at ambient temperature; with humidification with unheated chamber water; and with humidification with the chamber water at 31°C, 34°C, and 37°C. At each setting, after a 20 min stabilization period, measurements were taken. Comfort level at each setting was evaluated using a visual analog scale rated zero (least comfortable) to 10 (most comfortable). Temperature and relative and absolute humidity inside the helmet increased; however, the comfort scores significantly decreased as the humidification chamber water temperature increased. Regardless of the FIO2, statistically significantly highest comfort scores were obtained when humidification water, with and without active humidification, was at ambient temperature. Unacceptable absolute humidity was obtained only without humidification at room temperature when FIO2 was 0.5. With the clinical use of a helmet, for patient comfort and mucosal humidification during CPAP, the most desirable conditions are likely to be obtained by humidifying without heating, that is by leaving the water in the humidifier chamber at room temperature.

Children should wear helmets while ice-skating: a comparison of skating-related injuries.

Science.gov (United States)

McGeehan, Jennifer; Shields, Brenda J; Smith, Gary A

2004-07-01

This study compares injuries, especially head injuries, among ice-skaters with those among skateboarders, rollerskaters, and in-line skaters, to determine the need for helmet use during recreational ice-skating by children. A comparative study of a consecutive series of patients. The emergency department of a large, urban, academic, children's hospital. Children treated for injuries related to recreational ice-skating, skateboarding, rollerskating, and in-line skating. During a 31-month period, 419 consecutive children were evaluated in the emergency department for skating-related injuries. Children were predominantly male (53.9%), with a mean age of 10.0 years (SD: 3.0 years; median: 10.0 years; range: 1-18 years). The most frequent mechanism of injury was a fall. Overall, 76.5% of children (215 of 281 children) were reported to be wearing no protective equipment, such as a helmet or padding on the elbows or knees, at the time of injury. Ice-skaters were more likely to have adult supervision than were skateboarders (relative risk [RR]: 5.16; 95% confidence interval [CI]: 2.13-12.46), rollerskaters (RR: 1.21; 95% CI: 1.09-1.35), and in-line skaters (RR: 2.08; 95% CI: 1.72-2.51). Ice-skaters were at greater risk of injury to the head (20.0%) than were in-line skaters (4.9%) (RR: 4.09; 95% CI: 1.81-9.23); a weak difference was noted between ice-skaters and rollerskaters (9.9%) (RR: 2.18; 95% CI: 1.04-4.57), with no significant difference in head injuries between ice-skaters and skateboarders (15.9%) (RR: 1.60; 95% CI: 0.54-2.93). Ice-skaters demonstrated lacerations to the head in 68.8% of abnormal head examinations, compared with 37.0% for rollerskaters (RR: 1.86; 95% CI: 1.08-3.20) and 50.0% for in-line skaters (RR: 2.06; 95% CI: 1.35-3.16); however, there was no significant difference in lacerations to the head between ice-skaters and skateboarders (53.3%) (RR: 1.29; 95% CI: 0.76-2.19). Injuries to ice-skaters occurred more often in an indoor skating facility (92

HElmet therapy Assessment in infants with Deformed Skulls (HEADS: protocol for a randomised controlled trial

Directory of Open Access Journals (Sweden)

van Wijk Renske M

2012-07-01

Full Text Available Abstract Background In The Netherlands, helmet therapy is a commonly used treatment in infants with skull deformation (deformational plagiocephaly or deformational brachycephaly. However, evidence of the effectiveness of this treatment remains lacking. The HEADS study (HElmet therapy Assessment in Deformed Skulls aims to determine the effects and costs of helmet therapy compared to no helmet therapy in infants with moderate to severe skull deformation. Methods/design Pragmatic randomised controlled trial (RCT nested in a cohort study. The cohort study included infants with a positional preference and/or skull deformation at two to four months (first assessment. At 5 months of age, all children were assessed again and infants meeting the criteria for helmet therapy were asked to participate in the RCT. Participants were randomly allocated to either helmet therapy or no helmet therapy. Parents of eligible infants that do not agree with enrolment in the RCT were invited to stay enrolled for follow up in a non-randomisedrandomised controlled trial (nRCT; they were then free to make the decision to start helmet therapy or not. Follow-up assessments took place at 8, 12 and 24 months of age. The main outcome will be head shape at 24 months that is measured using plagiocephalometry. Secondary outcomes will be satisfaction of parents and professionals with the appearance of the child, parental concerns about the future, anxiety level and satisfaction with the treatment, motor development and quality of life of the infant. Finally, compliance and costs will also be determined. Discussion HEADS will be the first study presenting data from an RCT on the effectiveness of helmet therapy. Outcomes will be important for affected children and their parents, health care professionals and future treatment policies. Our findings are likely to influence the reimbursement policies of health insurance companies. Besides these health outcomes, we will be able to

Determinants of helmet use behaviour among employed motorcycle riders in Yazd, Iran based on theory of planned behaviour.

Science.gov (United States)

Ali, Mehri; Saeed, Mazloomy Mahmoodabad Seyed; Ali, Morowatisharifabad Mohammad; Haidar, Nadrian

2011-09-01

This paper reports on predictors of helmet use behaviour, using variables based on the theory of planned behaviour model among the employed motorcycle riders in Yazd-Iran, in an attempt to identify influential factors that may be addressed through intervention efforts. In 2007, a cluster random sample of 130 employed motorcycle riders in the city of Yazd in central Iran, participated in the study. Appropriate instruments were designed to measure the variables of interest (attitude, subjective norms, perceived behaviour control, intention along with helmet use behaviour). Reliability and validity of the instruments were examined and approved. The statistical analysis of the data included descriptive statistics, bivariate correlations, and multiple regression. Based on the results, 56 out of all the respondents (43.1%) had history of accident by motorcycle. Of these motorcycle riders only 10.7% were wearing their helmet at the time of their accident. Intention and perceived behavioural control showed a significant relationship with helmet use behaviour and perceived behaviour control was the strongest predictor of helmet use intention, followed by subjective norms, and attitude. It was found that that helmet use rate among motorcycle riders was very low. The findings of present study provide a preliminary support for the TPB model as an effective framework for examining helmet use in motorcycle riders. Understanding motorcycle rider's thoughts, feelings and beliefs about helmet use behaviour can assist intervention specialists to develop and implement effective programs in order to promote helmet use among motorcycle riders. Copyright © 2010 Elsevier Ltd. All rights reserved.

Motorcycle helmet type and the risk of head injury and neck injury during motorcycle collisions in California.

Science.gov (United States)

Erhardt, Taryn; Rice, Thomas; Troszak, Lara; Zhu, Motao

2016-01-01

The use of novelty motorcycle helmets is often prompted by beliefs that wearing a standard helmet can contribute to neck injury during traffic collisions. The goal of this analysis was to examine the association between helmet type and neck injury risk and the association between helmet type and head injury. Data were collected during the investigation of motorcycle collisions of any injury severity by the California Highway Patrol (CHP) and 83 local law enforcement agencies in California between June 2012 and July 2013. We estimated head injury and neck injury risk ratios from data on 7051 collision-involved motorcyclists using log-binomial regression. Helmet type was strongly associated with head injury occurrence but was not associated with the occurrence of neck injury. Rider age, rider alcohol use, and motorcycle speed were strong, positive predictors of both head and neck injury. Interventions to improve motorcycle helmet choice and to counteract misplaced concerns surrounding neck injury risk are likely to lead to reductions in head injury, brain injury, and death. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of socioeconomic status on the effectiveness of bicycle helmet legislation for children: a prospective observational study.

Science.gov (United States)

Parkin, Patricia C; Khambalia, Amina; Kmet, Leanne; Macarthur, Colin

2003-09-01

To evaluate the influence of average family income in a geographic area on the effectiveness of helmet legislation on observed helmet use by children (5-14 years). The study was conducted in East York, a health district of Metropolitan Toronto, in collaboration with the East York Health Unit. In 1996, the total population was 107 822, 11 340 of which were children 5 to 14 years. Census data were used to group the 21 census tracts in East York into 7 geographically distinct areas. The boundaries of these areas are natural barriers to travel, such as expressways, ravines, railway tracks, and hydroelectric power lines. The areas were also ranked according to average family income (based on Statistics Canada data). For analytical purposes, areas were defined as low-, mid-, and high-income areas. Census data profiles of the areas have been previously described. For each consecutive year from 1990 to 1997 inclusive, direct observations of children riding bicycles in East York during the months of April through October were made. In 1995, observations were completed before the introduction of the law on October 1, 1995. Only children who were between 5 and 14 years of age and riding a 2-wheeled bicycle were included in the study. In total, 111 sites across all 7 areas were selected for observation. Observational sites included school yards of all elementary and middle schools (kindergarten to grade 8) and all parks in East York. In addition, 5 major intersections and 5 residential streets from each area were randomly selected. Observers were trained and used a standardized data collection form. A pilot study showed that the data collected by observers were reliable and valid. Observers remained at each site for 1 hour and collected data on helmet use and sex. Ethical approval for the study was obtained from the Hospital for Sick Children Research Ethics Board, the East York Board of Education, and the Metropolitan Separate School Board. The proportion of children who were

Feasibility of nitric oxide administration by neonatal helmet-CPAP: a bench study.

Science.gov (United States)

Trevisanuto, Daniele; Doglioni, Nicoletta; Micaglio, Massimo; Zanardo, Vincenzo

2007-09-01

Inhaled nitric oxide (NO) may have a role in the treatment of preterm infants with respiratory failure. We evaluated the feasibility of administering NO therapy by a new continuous positive airway pressure (CPAP) system (neonatal helmet-CPAP). While maintaining a constant total flow of 8, 10, and 12 l.min(-1), NO concentrations were progressively increased to 5, 10, 20, and 40 p.p.m. in the neonatal helmet-CPAP pressure chamber (5 cmH2O). NO, NO2, and O2 concentrations were measured in the pressure chamber and the immediate external environment. In the chamber, NO2 levels remained low (neonatal helmet-CPAP system. This method allows the delivery of accurate NO levels and high O2 concentrations avoiding NO2 accumulation. Further experimental and clinical studies are needed.

Joint Service Aircrew Mask (JSAM) - Tactical Aircraft (TA) A/P22P-14A Respirator Assembly (V)5: Speech Intelligibility Performance with Double Hearing Protection, HGU-84/P Flight Helmet

Science.gov (United States)

2017-04-06

data does not license the holder or any other person or corporation; or convey any rights or permission to manufacture , use, or sell any patented...airworthiness. The JSAM-TA Respirator Assembly (V)5 (Figure 2) is a chemical, biological, and radiological respirator assembly manufactured by Cam Lock...Classic™ sizing matrix for speech intelligibility Subject ID# Gender HGU- 84/P Helmet Helmet Liner (inches) Earcup Spacers (centered behind

Societal cost of traumatic brain injury: A comparison of cost-of-injuries related to biking with and without helmet use.

Science.gov (United States)

Costa, Camille K; Dagher, Jehane H; Lamoureux, Julie; de Guise, Elaine; Feyz, Mitra

2015-01-01

The goal of this study is to determine if a difference in societal costs exists from traumatic brain injuries (TBI) in patients who wear helmets compared to non-wearers. This is a retrospective cost-of-injury study of 128 patients admitted to the Montreal General Hospital (MGH) following a TBI that occurred while cycling between 2007-2011. Information was collected from Quebec Trauma Registry. The independent variables collected were socio-demographic, helmet status, clinical and neurological patient information. The dependent variables evaluated societal costs. The median costs of hospitalization were significantly higher (p = 0.037) in the no helmet group ($7246.67 vs. $4328.17). No differences in costs were found for inpatient rehabilitation (p = 0.525), outpatient rehabilitation (p = 0.192), loss of productivity (p = 0.108) or death (p = 1.000). Overall, the differences in total societal costs between the helmet and no helmet group were not significantly different (p = 0.065). However, the median total costs for patients with isolated TBI in the non-helmet group ($22, 232.82) was significantly higher (p = 0.045) compared to the helmet group ($13, 920.15). Cyclists sustaining TBIs who did not wear helmets in this study were found to cost society nearly double that of helmeted cyclists.

The effect of helmet use on injury severity and crash circumstances in skiers and snowboarders.

Science.gov (United States)

Hagel, Brent; Pless, I Barry; Goulet, Claude; Platt, Robert; Robitaille, Yvonne

2005-01-01

The aim of this study was to examine the effect of helmet use on non-head-neck injury severity and crash circumstances in skiers and snowboarders. We used a matched case-control study over the November 2001 to April 2002 winter season. 3295 of 4667 injured skiers and snowboarders reporting to the ski patrol at 19 areas in Quebec with non-head, non-neck injuries agreed to participate. Cases included those evacuated by ambulance, admitted to hospital, with restriction of normal daily activities (NDAs) >6 days, with non-helmet equipment damage, fast self-reported speed, participating on a more difficult run than usual, and jumping-related injury. Controls were injured participants without severe injuries or high-energy crash circumstances and were matched to cases on ski area, activity, day, age, and sex. Conditional logistic regression was used to relate each outcome to helmet use. There was no evidence that helmet use increased the risk of severe injury or high-energy crash circumstances. The results suggest that helmet use in skiing and snowboarding is not associated with riskier activities that lead to non-head-neck injuries.

Development and testing of a flexible ballistic neck protection

NARCIS (Netherlands)

Roebroeks, G.H.J.J.; Rensink, P.

2016-01-01

Sufficient ballistic protection of the neck area would significantly reduce the vulnerability of an infantry soldier. So far this protection is offered by extensions on the ballistic vest or combat helmet. However, the requirements for head agility and the various body to head positions combined

Respiratory Protection Performance: Impact of Helmet Integration

Science.gov (United States)

2016-09-01

usage. In addition, NVG usage did not result in significant differences within the integrated or nonintegrated configurations. Figure 4 illustrates the...DISTRIBUTION LIST The following individuals and organizations were provided with one Adobe portable document format (pdf) electronic

Public bike sharing in New York City: helmet use behavior patterns at 25 Citi Bike™ stations.

Science.gov (United States)

Basch, Corey H; Ethan, Danna; Zybert, Patricia; Afzaal, Sarah; Spillane, Michael; Basch, Charles E

2015-06-01

Urban public bicycle sharing programs are on the rise in the United States. Launched in 2013, NYC's public bicycle share program, Citi Bike™ is the fastest growing program of its kind in the nation, with nearly 100,000 members and more than 330 docking stations across Manhattan and Brooklyn. The purpose of this study was to assess helmet use behavior among Citi Bike™ riders at 25 of the busiest docking stations. The 25 Citi Bike™ Stations varied greatly in terms of usage: total number of cyclists (N = 96-342), commute versus recreation (22.9-79.5% commute time riders), weekday versus weekend (6.0-49.0% weekend riders). Helmet use ranged between 2.9 and 29.2% across sites (median = 7.5 %). A total of 4,919 cyclists were observed, of whom 545 (11.1%) were wearing helmets. Incoming cyclists were more likely to wear helmets than outgoing cyclists (11.0 vs 5.9%, p = .000). NYC's bike share program endorses helmet use, but relies on education to encourage it. Our data confirm that, to date, this strategy has not been successful.

Electrostatic Properties of Selected Personal Protective Equipment Regarding Explosion Hazard

Directory of Open Access Journals (Sweden)

Marcin Jachowicz

2013-01-01

Full Text Available In industries such as the mining, petrochemistry or power industries, personal protective equipment is often used in explosive atmospheres. What causes the occurrence of explosive hazards is ever-present in the work environment they include, electrostatic phenomena as well as the build-up of electrical charges on the surface of the protective equipment used. This paper presents the results of studies which were aimed at determining the fundamental electrostatic parameters of protective helmets as well as eye and face protection, surface resistance and the voltage of electrostatic fields. Examinations on the typical structure of the above mentioned equipment was conducted including the variable values of ambient humidity, which can occur in the working environment and with the use of various types of materials used to generate a charge. The adopted methods and testing equipment have been presented. Using the current, general requirements regarding the electrostatic properties of materials, the examined helmets and eye protection were assessed for their use in explosive atmospheres.

The formulation and implementation of a national helmet law: a case study from Viet Nam.

Science.gov (United States)

Passmore, Jonathon W; Nguyen, Lan Huong; Nguyen, Nam Phuong; Olivé, Jean-Marc

2010-10-01

Road traffic injuries are a leading cause of death and disability in Viet Nam. In 2008, official data reported 11 243 deaths and 7771 serious injuries on the roads, of which an estimated 60% of fatalities occur in motorcycle riders and passengers. In recognition of this problem, Viet Nam has had partial motorcycle helmet legislation since 1995. However, for a variety of reasons, implementation and enforcement have been limited. On 15 December 2007, Viet Nam's first comprehensive mandatory helmet law came into effect, covering all riders and passengers on all roads nationwide. Penalties increased ten-fold and cohorts of police were mobilized for enforcement. The Viet Nam national helmet legislation was developed and implemented by the National Traffic Safety Committee. Despite past barriers to enforcement, increased policing in 2008 led to 680 000 infringements being issued for non-helmet wearing. While changes in helmet wearing were not nationally observed, significant increases were documented in selected provinces in the first six months of the law's introduction. In Da Nang, helmet wearing increased from 27 to 99%. In the first three months after the law took effect, surveillance data from 20 urban and rural hospitals, found the risk of road traffic head injuries and deaths decreased by 16% and 18% respectively. Political leadership, intensive advanced public education and stringent enforcement have contributed to the successful implementation of the new law. Through continual monitoring of the legislation, loopholes detrimental to the effectiveness of the law have been identified and addressed.

The Influence of Various Factors on High School Football Helmet Face Mask Removal: A Retrospective, Cross-Sectional Analysis

Science.gov (United States)

Swartz, Erik E; Decoster, Laura C; Norkus, Susan A; Cappaert, Thomas A

2007-01-01

Context: Most research on face mask removal has been performed on unused equipment. Objective: To identify and compare factors that influence the condition of helmet components and their relationship to face mask removal. Design: A cross-sectional, retrospective study. Setting: Five athletic equipment reconditioning/recertification facilities. Participants: 2584 helmets from 46 high school football teams representing 5 geographic regions. Intervention(s): Helmet characteristics (brand, model, hardware components) were recorded. Helmets were mounted and face mask removal was attempted using a cordless screwdriver. The 2004 season profiles and weather histories were obtained for each high school. Main Outcome Measure(s): Success and failure (including reason) for removal of 4 screws from the face mask were noted. Failure rates among regions, teams, reconditioning year, and screw color (type) were compared. Weather histories were compared. We conducted a discriminant analysis to determine if weather variables, region, helmet brand and model, reconditioning year, and screw color could predict successful face mask removal. Metallurgic analysis of screw samples was performed. Results: All screws were successfully removed from 2165 (84%) helmets. At least 1 screw could not be removed from 419 (16%) helmets. Significant differences were found for mean screw failure per helmet among the 5 regions, with the Midwest having the lowest failure rate (0.08 ± 0.38) and the Southern (0.33 ± 0.72), the highest. Differences were found in screw failure rates among the 46 teams (F1,45 = 9.4, P < .01). Helmets with the longest interval since last reconditioning (3 years) had the highest failure rate, 0.47 ± 0.93. Differences in success rates were found among 4 screw types (χ21,4 = 647, P < .01), with silver screws having the lowest percentage of failures (3.4%). A discriminant analysis (Λ = .932, χ214,n=2584 = 175.34, P < .001) revealed screw type to be the strongest predictor of

Elevated Extravascular Lung Water Index (ELWI) as a Predictor of Failure of Continuous Positive Airway Pressure Via Helmet (Helmet-CPAP) in Patients With Acute Respiratory Failure After Major Surgery.

Science.gov (United States)

Redondo Calvo, Francisco Javier; Bejarano Ramirez, Natalia; Uña Orejon, Rafael; Villazala Garcia, Ruben; Yuste Peña, Ana Sofia; Belda, Francisco Javier

2015-11-01

NIV is increasingly used for prevention and treatment of respiratory complications and failure. Some of them are admitted to the PACU with advanced hemodynamic monitors which allow quantification of Extravascular Lung Water (EVLW) by transpulmonary thermodilution technique (TPTD) and Pulmonary Vascular Permeability (PVP) providing information on lung edema. The objective of this study was to ascertain if EVLW Index and PVP Index may predict failure (intubation) or success (non-intubation) in patients developing acute respiratory failure (ARF) in the postoperative period following major abdominal surgery, where the first line of treatment was non-invasive continuous positive airway pressure via a helmet. Hemodynamic variables, EVLWI and PVPI were monitored with a transpulmonary thermodilution hemodynamic monitor device (PiCCO™) before and after the application of CPAP. Avoidance of intubation was observed in 66% of patients with Helmet-CPAP. In these patients after the first hour of application of CPAP, PaO2/FiO2 ratio significantly increased (303.33±65.2 vs. 141.6±14.6, P<.01). Before starting Helmet-CPAP values of EVLWI and PVPI were significantly lower in non-intubated patients (EVLWI 8.6±1.08 vs. 11.8±0.99ml/kg IBW, P<.01 and PVPI 1.7±0.56 vs. 3.0±0.88, P<.01). An optimal cut-off value for EVLWI was established at 9.5, and at 2.45 for PVPI (sensitivity of 0.7; specificity of 0.9, P<.01). In this type of patient the physiological parameters that predict the failure of Helmet-CPAP with the greatest accuracy were the value of the EVLWI and PVPI before Helmet-CPAP institution and the PaO2/FiO2 ratio and the respiratory rate after one hour of CPAP. Copyright © 2014 SEPAR. Published by Elsevier Espana. All rights reserved.

Dynamic simulation and finite element analysis of the human mandible injury protected by polyvinyl alcohol sponge

Energy Technology Data Exchange (ETDEWEB)

Karimi, Alireza; Navidbakhsh, Mahdi, E-mail: mnavid@iust.ac.ir; Razaghi, Reza

2014-09-01

There have been intensive efforts to find a suitable kinetic energy absorbing material for helmet and bulletproof vest design. Polyvinyl alcohol (PVA) sponge is currently in extensive use as scaffolding material for tissue engineering applications. PVA can also be employed instead of commonly use kinetic energy absorbing materials to increase the kinetic energy absorption capacity of current helmet and bulletproof vest materials owing to its excellent mechanical properties. In this study, a combined hexahedral finite element (FE) model is established to determine the potential protection ability of PVA sponge in controlling the level of injury for gunshot wounds to the human mandible. Digital computed tomography data for the human mandible are used to establish a three-dimensional FE model of the human mandible. The mechanism by which a gunshot injures the protected mandible by PVA sponge is dynamically simulated using the LS-DYNA code under two different shot angles. The stress distributions in different parts of the mandible and sponge after injury are also simulated. The modeling results regardless of shot angle reveal that the substantial amount of kinetic energy of the steel ball (67%) is absorbed by the PVA sponge and, consequently, injury severity of the mandible is significantly decreased. The highest energy loss (170 J) is observed for the impact at entry angle of 70°. The results suggest the application of the PVA sponge as an alternative reinforcement material in helmet and bulletproof vest design to absorb most of the impact energy and reduce the transmitted load. - Highlights: • The ability of PVA sponge to control the injury to the human mandible is computed. • A hexahedral FE model for gunshot wounds to the human mandible is established. • The kinetic energy and injury severity of the mandible is minimized by the sponge. • The highest energy loss (170 J) is observed for the impact at entry angle of 70°. • PVA suggests as an alternative

A Materials Approach in the Development of Multi-Threat Warfighter Head Protection

Science.gov (United States)

2008-12-01

TUSJp TYSlp ’--- --"IO,,5083-="" H13 .’ (AI) ’AZ31B-H2’",(~",),,-- __ Figure 6. Specific Strength of Mg vs. Al Alloy Armor Plate of current interest because...perfonnance in metal alloys, and higher stiffness typically contributes to enhanced energy absorption upon ballistic impact ; therefore, one would predict...Helmets, and ballistic helmets in particular. have not been dominated by stiffness requirements but rather other properties (e.g., crash, impact

The burden of motorcycle-related neuro-trauma in Ireland and associated helmet usage.

LENUS (Irish Health Repository)

Murphy, R K J

2009-04-01

Motorcycles represent less than 2% of the licensed vehicles but motorcyclists account for 12% of road deaths in Ireland. The British Road Safety Authority has introduced the Sharp programme, which hopes to save 50 lives in the U.K. each year alone by helping riders to choose the best-fitting and safest helmets. We evaluated the pattern of head injuries sustained by motorcyclists referred to the two neurosurgical centres Beaumont Hospital and Cork University Hospital in Ireland and ascertained if the new SHARP guidelines could be of benefit in reducing the burden of motorcycle related neurotrauma and disability in Ireland. Despite Ireland having mandatory helmet laws almost a quarter of our motorcyclists with traumatic brain injury were unhelmeted. A significant reduction in mortality and morbidity is predicted if all motorcyclists in Ireland were to wear helmets that satisfied the SHARP criteria.

Self-Powered Safety Helmet Based on Hybridized Nanogenerator for Emergency.

Science.gov (United States)

Jin, Long; Chen, Jun; Zhang, Binbin; Deng, Weili; Zhang, Lei; Zhang, Haitao; Huang, Xi; Zhu, Minhao; Yang, Weiqing; Wang, Zhong Lin

2016-08-23

The rapid development of Internet of Things and the related sensor technology requires sustainable power sources for their continuous operation. Scavenging and utilizing the ambient environmental energy could be a superior solution. Here, we report a self-powered helmet for emergency, which was powered by the energy converted from ambient mechanical vibration via a hybridized nanogenerator that consists of a triboelectric nanogenerator (TENG) and an electromagnetic generator (EMG). Integrating with transformers and rectifiers, the hybridized nanogenerator can deliver a power density up to 167.22 W/m(3), which was demonstrated to light up 1000 commercial light-emitting diodes (LEDs) instantaneously. By wearing the developed safety helmet, equipped with rationally designed hybridized nanogenerator, the harvested vibration energy from natural human motion is also capable of powering a wireless pedometer for real-time transmitting data reporting to a personal cell phone. Without adding much extra weight to a commercial one, the developed wearing helmet can be a superior sustainable power source for explorers, engineers, mine-workers under well, as well as and disaster-relief workers, especially in remote areas. This work not only presents a significant step toward energy harvesting from human biomechanical movement, but also greatly expands the applicability of TENGs as power sources for self-sustained electronics.

Football helmet drop tests on different fields using an instrumented Hybrid III head.

Science.gov (United States)

Viano, David C; Withnall, Chris; Wonnacott, Michael

2012-01-01

An instrumented Hybrid III head was placed in a Schutt ION 4D football helmet and dropped on different turfs to study field types and temperature on head responses. The head was dropped 0.91 and 1.83 m giving impacts of 4.2 and 6.0 m/s on nine different football fields (natural, Astroplay, Fieldturf, or Gameday turfs) at turf temperatures of -2.7 to 23.9 °C. Six repeat tests were conducted for each surface at 0.3 m (1') intervals. The Hybrid III was instrumented with triaxial accelerometers to determine head responses for the different playing surfaces. For the 0.91-m drops, peak head acceleration varied from 63.3 to 117.1 g and HIC(15) from 195 to 478 with the different playing surfaces. The lowest response was with Astroplay, followed by the engineered natural turf. Gameday and Fieldturf involved higher responses. The differences between surfaces decreased in the 1.83 m tests. The cold weather testing involved higher accelerations, HIC(15) and delta V for each surface. The helmet drop test used in this study provides a simple and convenient means of evaluating the compliance and energy absorption of football playing surfaces. The type and temperature of the playing surface influence head responses.

Continuous positive airway pressure with helmet versus mask in infants with bronchiolitis: an RCT.

Science.gov (United States)

Chidini, Giovanna; Piastra, Marco; Marchesi, Tiziana; De Luca, Daniele; Napolitano, Luisa; Salvo, Ida; Wolfler, Andrea; Pelosi, Paolo; Damasco, Mirco; Conti, Giorgio; Calderini, Edoardo

2015-04-01

Noninvasive continuous positive airway pressure (CPAP) is usually applied with a nasal or facial mask to treat mild acute respiratory failure (ARF) in infants. A pediatric helmet has now been introduced in clinical practice to deliver CPAP. This study compared treatment failure rates during CPAP delivered by helmet or facial mask in infants with respiratory syncytial virus-induced ARF. In this multicenter randomized controlled trial, 30 infants with respiratory syncytial virus-induced ARF were randomized to receive CPAP by helmet (n = 17) or facial mask (n = 13). The primary endpoint was treatment failure rate (defined as due to intolerance or need for intubation). Secondary outcomes were CPAP application time, number of patients requiring sedation, and complications with each interface. Compared with the facial mask, CPAP by helmet had a lower treatment failure rate due to intolerance (3/17 [17%] vs 7/13 [54%], P = .009), and fewer infants required sedation (6/17 [35%] vs 13/13 [100%], P = .023); the intubation rates were similar. In successfully treated patients, CPAP resulted in better gas exchange and breathing pattern with both interfaces. No major complications due to the interfaces occurred, but CPAP by mask had higher rates of cutaneous sores and leaks. These findings confirm that CPAP delivered by helmet is better tolerated than CPAP delivered by facial mask and requires less sedation. In addition, it is safe to use and free from adverse events, even in a prolonged clinical setting. Copyright © 2015 by the American Academy of Pediatrics.

The Cyclists Helmet Study in Juba, Southern Sudan, 2006

African Journals Online (AJOL)

Ann Burgess

Juba has a poor road network and few public transport options, with an increasing number of people riding ... The conclusion is that cyclists need information on the importance of wearing a helmet. ... Leading safety advocates recommend the.

Development and field performance of indy race car head impact padding.

Science.gov (United States)

Melvin, J W; Bock, H; Anderson, K; Gideon, T

2001-11-01

The close-fitting cockpit of the modern Indy car single seat race car has the potential to provide a high level of head and neck impact protection in rear and side impacts. Crash investigation has shown that a wide variety of materials have been used as the padding for these cockpits and, as a result, produced varying outcomes in crashes. Additionally, these pads have not always been positioned for optimal performance. The purpose of this study was to investigate the head impact performance of a variety of energy-absorbing padding materials under impact conditions typical of Indy car rear impacts and to identify superior materials and methods of improving their performance as race car head pads. An extensive series of tests with the helmeted Hybrid III test dummy head and neck on an impact mini-sled was conducted to explore head padding concepts. Following this, a performance specification for a simplified impact test using a rigid headform that simulates the helmeted head was developed and recommendations for performance levels of head padding based on biomechanical data on helmeted head impacts were made. In 1997, during the time that the head pad research was being performed, the Indy Racing League introduced a new chassis specification for their cars. There were a number of rear- and side-impact crashes during that season that resulted in seven severe head injuries. Examples of the head padding in those cars were included in the experimental study. The results of the head pad research were used to specify new padding materials that met the new biomechanical criteria. The placement of the head pads was also changed for better location of the padding. These changes instituted in 1998 have reduced the number of head injuries in crashes similar to or more severe than those of 1997 and have resulted in only occasional moderate head injuries (concussions) in the 1998 and 1999 seasons.

Guardian Caps: What's the Impact?

Science.gov (United States)

Jenny, Seth E.; Rouse, Wardell; Seibles, Ashlie

2017-01-01

Reported sport-related concussion rates have dramatically increased recently. In response, the Guardian company has emerged as a leading manufacturer of soft-shell helmet covers. The "Guardian Cap" is a foam padded covering that fits over a helmet that aims to reduce the impact of collisions and lessen the chance of a concussion. The…

Structural Equation Modelling in Behavioral Intention to Use Safety Helmet Reminder System

Directory of Open Access Journals (Sweden)

Rosli Naida

2016-01-01

Full Text Available Motorcycle is one of private transportation which has been widely used in many countries including Malaysia. However, motorcycles are the most dangerous form of motorized transport. Royal Malaysian Police (PDRM statistics recorded that motorcycle is the highest vehicle (45.9% involved in traffic accident compared to other vehicles. The potential cause of the death to the motorcyclist was due to the head injury. One of strategy to mitigate this problem is through proper usage of safety helmet. Therefore, this paper was introduce a new approach on motorcyclist safety by using the Technology Acceptance Model (TAM with additional determinants that contribute to behavioral intention and to increase the proper usage of safety helmets among Malaysian motorcyclists. The Structural Equation Modelling (SEM was used to test the structural TAM proposed. The evaluation for structural model showed the goodness of fit indices are excellent fit. This study found that perceived ease of use, perceived usefulness and social norm are significant towards behavioral intention to use Safety Helmet Reminder System (SHR.

Effect of Filters on the Noise Generated by Continuous Positive Airway Pressure Delivered via a Helmet

Directory of Open Access Journals (Sweden)

Ricardo Hernández-Molina

2017-01-01

Full Text Available Introduction: One of the problems that the delivery of continuous positive airway pressure (CPAP via a helmet poses is the generation of noise. The objective of our study was to assess the effect that the use of filter has on sound pressure levels generated by the delivery of positive airway pressure at different gas flow rates. Materials and Methods: Sound pressure levels generated by neonatal helmet CPAP delivery were measured at different gas flows (20, 30, and 40 l/min with and without a breathing filter. Noise intensity was measured by installing microphones in the inner ear of dummy heads wearing helmets. Results: The sound pressure level increased by 38% at a gas flow of 40 l/min, as compared to a gas flow of 20 l/min {74 dBA [interquartile range (IQR 2,2] vs 52 dBA (IQR 5,9, respectively}. Using the breathing filter as a diffuser has a variety of effects on sound pressure levels according to the gas flow rate. Conclusion: The intensity of the noise generated by helmet delivery of positive airway pressure depends on the type of helmet used, gas flow, and use or not of a diffuser filter. Breathing filters with gas flows over 30 l/min might not be recommended since they would not attenuate but will rather amplify sound pressure.

Simulation study comparing the helmet-chin PET with a cylindrical PET of the same number of detectors

Science.gov (United States)

Ahmed, Abdella M.; Tashima, Hideaki; Yoshida, Eiji; Nishikido, Fumihiko; Yamaya, Taiga

2017-06-01

There is a growing interest in developing brain PET scanners with high sensitivity and high spatial resolution for early diagnosis of neurodegenerative diseases and studies of brain functions. Sensitivity of the PET scanner can be improved by increasing the solid angle. However, conventional PET scanners are designed based on a cylindrical geometry, which may not be the most efficient design for brain imaging in terms of the balance between sensitivity and cost. We proposed a dedicated brain PET scanner based on a hemispheric shape detector and a chin detector (referred to as the helmet-chin PET), which is designed to maximize the solid angle by increasing the number of lines-of-response in the hemisphere. The parallax error, which PET scanners with a large solid angle tend to have, can be suppressed by the use of depth-of-interaction detectors. In this study, we carry out a realistic evaluation of the helmet-chin PET using Monte Carlo simulation based on the 4-layer GSO detector which consists of a 16  ×  16  ×  4 array of crystals with dimensions of 2.8  ×  2.8  ×  7.5 mm3. The purpose of this simulation is to show the gain in imaging performance of the helmet-chin PET compared with the cylindrical PET using the same number of detectors in each configuration. The sensitivity of the helmet-chin PET evaluated with a cylindrical phantom has a significant increase, especially at the top of the (field-of-view) FOV. The peak-NECR of the helmet-chin PET is 1.4 times higher compared to the cylindrical PET. The helmet-chin PET provides relatively low noise images throughout the FOV compared to the cylindrical PET which exhibits enhanced noise at the peripheral regions. The results show the helmet-chin PET can significantly improve the sensitivity and reduce the noise in the reconstructed images.

16 CFR 1203.11 - Marking the impact test line.

Science.gov (United States)

2010-01-01

... Section 1203.11 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT... (HPI), with the brow parallel to the basic plane. Place a 5-kg (11-lb) preload ballast on top of the... helmet coinciding with the intersection of the surface of the helmet with the impact line planes defined...

Protective Equipment and Player Characteristics Associated With the Incidence of Sport-Related Concussion in High School Football Players

Science.gov (United States)

McGuine, Timothy A.; Hetzel, Scott; McCrea, Michael; Brooks, M. Alison

2015-01-01

Background The incidence of sport-related concussion (SRC) in high school football is well documented. However, limited prospective data are available regarding how player characteristics and protective equipment affect the incidence of SRC. Purpose To determine whether the type of protective equipment (helmet and mouth guard) and player characteristics affect the incidence of SRC in high school football players. Design Cohort study; Level of evidence, 2. Methods Certified athletic trainers (ATs) at each high school recorded the type of helmet worn (brand, model, purchase year, and recondition status) by each player as well as information regarding players’ demographics, type of mouth guard used, and history of SRC. The ATs also recorded the incidence and days lost from participation for each SRC. Incidence of SRC was compared for various helmets, type of mouth guard, history of SRC, and player demographics. Results A total of 2081 players (grades 9–12) enrolled during the 2012 and/or 2013 football seasons (2287 player-seasons) and participated in 134,437 football (practice or competition) exposures. Of these players, 206 (9%) sustained a total of 211 SRCs (1.56/1000 exposures). There was no difference in the incidence of SRC (number of helmets, % SRC [95% CI]) for players wearing Riddell (1171, 9.1% [7.6%–11.0%]), Schutt (680, 8.7% [6.7%–11.1%]), or Xenith (436, 9.2% [6.7%–12.4%]) helmets. Helmet age and recondition status did not affect the incidence of SRC. The rate of SRC (hazard ratio [HR]) was higher in players who wore a custom mouth guard (HR = 1.69 [95% CI, 1.20–2.37], P football players. Players who had sustained an SRC within the previous 12 months were more likely to sustain an SRC than were players without a history of SRC. Sports medicine providers who work with high school football players need to realize that factors other than the type of protective equipment worn affect the risk of SRC in high school players. PMID:25060072

Sir Hugh Cairns: The neurosurgeon who introduced crash helmets

Directory of Open Access Journals (Sweden)

Shahsivadhanan Sundaravadhanan

2017-01-01

Full Text Available Statistics prove that more Indians die in Road traffic related accidents than in wars. Prior to World War II, the death toll across the world used to be very high. It was at this juncture that a Military Neurosurgeon named Hugh Cairns introduced the compulsory wearing of crash helmets and brought about a reduction in mortality by more than 50%. Within a decade of introduction of crash helmets in Britain, the entire world followed suit. The results of his efforts are here for all of us to see. This innovative military neurosurgeon is credited as the one who introduced the concept of mobile neurosurgical units during world war and also the first proponent of usage of penicillin in war. His concepts in war surgery are still followed by militaries across the world. This article comes as a tribute to this great Neurosurgeon who helped in saving millions of lives.

Outcome analysis after helmet therapy using 3D photogrammetry in patients with deformational plagiocephaly: the role of root mean square.

Science.gov (United States)

Moghaddam, Mahsa Bidgoli; Brown, Trevor M; Clausen, April; DaSilva, Trevor; Ho, Emily; Forrest, Christopher R

2014-02-01

Deformational plagiocephaly (DP) is a multifactorial non-synostotic cranial deformity with a reported incidence as high as 1 in 7 infants in North America. Treatment options have focused on non-operative interventions including head repositioning and the use of an orthotic helmet device. Previous studies have used linear and two dimensional outcome measures to assess changes in cranial symmetry after helmet therapy. Our objective was to demonstrate improvement in head shape after treatment with a cranial molding helmet by using Root Mean Square (RMS), a measure unique to 3D photogrammetry, which takes into account both changes in volume and shape over time. Three dimensional photographs were obtained before and after molding helmet treatment in 40 infants (4-10 months old) with deformational plagiocephaly. Anatomical reference planes and measurements were recorded using the 3dMD Vultus(®) analysis software. RMS was used to quantify symmetry by superimposing left and right quadrants and calculating the mean value of aggregate distances between surfaces. Over 95% of the patients demonstrated an improvement in symmetry with helmet therapy. Furthermore, when the sample of infants was divided into two treatment subgroups, a statistically significant correlation was found between the age at the beginning of treatment and the change in the RMS value. When helmet therapy was started before 7 months of age a greater improvement in symmetry was seen. This work represents application of the technique of RMS analysis to demonstrate the efficacy of treatment of deformational plagiocephaly with a cranial molding helmet. Copyright © 2014. Published by Elsevier Ltd.

Randomized Comparison of Helmet CPAP Versus High-Flow Nasal Cannula Oxygen in Pediatric Respiratory Distress.

Science.gov (United States)

Vitaliti, Giovanna; Vitaliti, Maria Concetta; Finocchiaro, Maria Carla; Di Stefano, Vita Antonella; Pavone, Piero; Matin, Nassim; Motamed-Gorji, Nazgol; Lubrano, Riccardo; Falsaperla, Raffaele

2017-08-01

The current study aimed to compare the efficacy and safety of 2 noninvasive respiratory support methods, which included helmet CPAP and high-flow nasal cannula (HFNC) in children with respiratory distress admitted to a pediatric intermediate care unit. This study was a prospective observational study conducted on children with respiratory distress (age 1-24 months) who were admitted to our acute and emergency operative unit. All included subjects were randomly treated with helmet CPAP or HFNC in a 1:1 fashion until their clinical picture, oxygen saturation, and arterial blood gas (ABG) parameters resolved. The efficiencies of helmet CPAP and HFNC were evaluated by breathing frequency, S pO 2 , ABG pH, ABG P aCO 2 , ABG P aO 2 , and P aO 2 /F IO 2 , recorded once at baseline and then after 1 and 6 h of treatment. Both noninvasive respiratory support modalities were compared with a control group of subjects with respiratory distress under standard therapeutic pharmaceutical protocols. We found that both helmet CPAP and HFNC were efficient in improving the clinical conditions of subjects with mild-to-moderate respiratory distress, although clinical response to helmet CPAP was more efficient and rapid compared with HFNC. Children who received respiratory support had a better clinical course in terms of hospitalization, days of intravenous rehydration therapy, and days of drug administration compared with the control group ( P CPAP and HFNC in respiratory distress resolution in a pediatric intermediate care setting. It aims to identify the most efficient treatment to avoid pediatric ICU admissions and endotracheal intubation and reduce the administration of drugs and days of hospitalization. Copyright © 2017 by Daedalus Enterprises.

Defining Constellation Suit Helmet Field of View Requirements Employing a Mission Segment Based Reduction Process

Science.gov (United States)

McFarland, Shane

2009-01-01

Field of view has always been a design feature paramount to helmets, and in particular space suits, where the helmet must provide an adequate field of view for a large range of activities, environments, and body positions. For Project Constellation, a different approach to helmet requirement maturation was utilized; one that was less a direct function of body position and suit pressure and more a function of the mission segment in which the field of view will be required. Through taxonimization of various parameters that affect suited field of view, as well as consideration for possible nominal and contingency operations during that mission segment, a reduction process was employed to condense the large number of possible outcomes to only six unique field of view angle requirements that still captured all necessary variables while sacrificing minimal fidelity.

Further Analysis of Motorcycle Helmet Effectiveness Using CODES Linked Data

Science.gov (United States)

1998-01-01

Linked data from the Crash Outcome Data Evaluation System (CODES) in seven : states was used by the National Highway Traffic Safety Administration as the : basis of a 1996 Report to Congress on the Benefits of Safety Belts and : Motorcycle Helmets (D...

SYMPATHETIC FILAMENT ERUPTIONS FROM A BIPOLAR HELMET STREAMER IN THE SUN

International Nuclear Information System (INIS)

Yang Jiayan; Jiang Yunchun; Zheng Ruisheng; Bi Yi; Hong Junchao; Yang Bo

2012-01-01

On 2005 August 5, two solar filaments erupted successively from different confined arcades underlying a common overarching multiple-arcade bipolar helmet streamer. We present detailed observations of these two events and identify them as sympathetic filament eruptions. The first (F1) is a small active-region filament located near the outskirts of the streamer arcade. It underwent a nonradial eruption, initially moving in the interior of the streamer arcade and resulting in an over-and-out coronal mass ejection. The second filament (F2), a larger quiescent one far away from F1, was clearly disturbed during the F1 eruption. It then underwent a very slow eruption and finally disappeared completely and permanently. Because two belt-shaped diffuse dimmings formed along the footprints of the streamer arcade in the first eruption and persisted throughout the complete disappearance of F2, the eruption series are interpreted as sympathetic: the simple expansion of the common streamer arcade forced by the F1 eruption weakened magnetic flux overlying F2 and thus led to its slow eruption, with the dimming formation indicating their physical connection. Our observations suggest that multiple-arcade bipolar helmet-streamer configurations are appropriate to producing sympathetic eruptions. Combined with the recent observations of unipolar-streamer sympathetic events, it appears that a multiple-arcade unipolar or bipolar helmet streamer can serve as a common magnetic configuration for sympathetic eruptions.

GPK helmet for protection from gas and dust

Energy Technology Data Exchange (ETDEWEB)

Ilinskiy, E.G.; Kogan, Yu.A.; Mazanenko, V.P.

1983-01-01

An examination is made of the purpose, area of application, operating principle, technical characteristics, and also results of testing a new device for individual protection of miners from gas and dust are examined.

Similarities and differences between on-scalp and conventional in-helmet magnetoencephalography recordings.

Directory of Open Access Journals (Sweden)

Lau M Andersen

Full Text Available The development of new magnetic sensor technologies that promise sensitivities approaching that of conventional MEG technology while operating at far lower operating temperatures has catalysed the growing field of on-scalp MEG. The feasibility of on-scalp MEG has been demonstrated via benchmarking of new sensor technologies performing neuromagnetic recordings in close proximity to the head surface against state-of-the-art in-helmet MEG sensor technology. However, earlier work has provided little information about how these two approaches compare, or about the reliability of observed differences. Herein, we present such a comparison, based on recordings of the N20m component of the somatosensory evoked field as elicited by electric median nerve stimulation. As expected from the proximity differences between the on-scalp and in-helmet sensors, the magnitude of the N20m activation as recorded with the on-scalp sensor was higher than that of the in-helmet sensors. The dipole pattern of the on-scalp recordings was also more spatially confined than that of the conventional recordings. Our results furthermore revealed unexpected temporal differences in the peak of the N20m component. An analysis protocol was therefore developed for assessing the reliability of this observed difference. We used this protocol to examine our findings in terms of differences in sensor sensitivity between the two types of MEG recordings. The measurements and subsequent analysis raised attention to the fact that great care has to be taken in measuring the field close to the zero-line crossing of the dipolar field, since it is heavily dependent on the orientation of sensors. Taken together, our findings provide reliable evidence that on-scalp and in-helmet sensors measure neural sources in mostly similar ways.

Factors associated with the enactment of safety belt and motorcycle helmet laws.

Science.gov (United States)

Law, Teik Hua; Noland, Robert B; Evans, Andrew W

2013-07-01

It has been shown that road safety laws, such as motorcycle helmet and safety belt laws, have a significant effect in reducing road fatalities. Although an expanding body of literature has documented the effects of these laws on road safety, it remains unclear which factors influence the likelihood that these laws are enacted. This study attempts to identify the factors that influence the decision to enact safety belt and motorcycle helmet laws. Using panel data from 31 countries between 1963 and 2002, our results reveal that increased democracy, education level, per capita income, political stability, and more equitable income distribution within a country are associated with the enactment of road safety laws. © 2012 Society for Risk Analysis.

Ballistic Impact Resistance of Plain Woven Kenaf/Aramid Reinforced Polyvinyl Butyral Laminated Hybrid Composite

Directory of Open Access Journals (Sweden)

Suhad D. Salman

2016-07-01

Full Text Available Traditionally, the helmet shell has been used to provide protection against head injuries and fatalities caused by ballistic threats. In this study, because of the high cost of aramid fibres and the necessity for environmentally friendly alternatives, a portion of aramid was replaced with plain woven kenaf fibre, with different arrangements and thicknesses, without jeopardising the requirements demanded by U.S. Army helmet specifications. Furthermore, novel helmets were produced and tested to reduce the dependency on the ballistic resistance components. Their use could lead to helmets that are less costly and more easily available than conventional helmet armour. The hybrid materials subjected to ballistic tests were composed of 19 layers and were fabricated by the hot press technique using different numbers and configurations of plain woven kenaf and aramid layers. In the case of ballistic performance tests, a positive effect was found for the hybridisation of kenaf and aramid laminated composites.

Helmets: A Threat to the Preservation of Women's Lacrosse

Science.gov (United States)

Bull, Ashley; Cavanaugh, Lauren

2016-01-01

A recent debate has raised controversy over the implementation of helmets in the game of women's lacrosse. Women have been participating in this game of finesse and skill without the need for safety equipment, yet in the past decade goggles have been mandated to compensate for the technological advancements in equipment that has increased the…

Brain tissue strains vary with head impact location: A possible explanation for increased concussion risk in struck versus striking football players.

Science.gov (United States)

Elkin, Benjamin S; Gabler, Lee F; Panzer, Matthew B; Siegmund, Gunter P

2018-03-29

On-field football helmet impacts over a large range of severities have caused concussions in some players but not in other players. One possible explanation for this variability is the struck player's helmet impact location. We examined the effect of impact location on regional brain tissue strain when input energy was held constant. Laboratory impacts were performed at 12 locations distributed over the helmet and the resulting head kinematics were simulated in two finite element models of the brain: the Simulated Injury Monitor and the Global Human Body Model Consortium brain model. Peak kinematics, injury metrics and brain strain varied significantly with impact location. Differences in impact location explained 33 to 37% of the total variance in brain strain for the whole brain and cerebrum, considerably more than the variance explained by impact location for the peak resultant head kinematics (8 to 23%) and slightly more than half of the variance explained by the difference in closing speed (57 to 61%). Both finite element models generated similar strain results, with minor variations for impacts that generated multi-axial rotations, larger variations in brainstem strains for some impact locations and a small bias for the cerebellum. Based on this experimental and computational simulation study, impact location on the football helmet has a large effect on regional brain tissue strain. We also found that the lowest strains consistently occurred in impacts to the crown and forehead, helmet locations commonly associated with the striking player. Copyright © 2018 Elsevier Ltd. All rights reserved.

Confinement lowers fertility rate of helmeted guinea fowl ( Numida ...

African Journals Online (AJOL)

... common game bird in Africa and there have been efforts to domesticate it for use as a source of human food. An important obstacle in successful domestication of guinea fowl is their low fertility rate.We studied the effects of semi-confinement on the fertility rates of helmeted guinea fowl by comparing egg fertility, hatch rate ...

Protective Eyewear

Science.gov (United States)

... that’s attached to a helmet. Are you a football player? Always wear your helmet with an attached ... Media Policies and Other Important Links NEI Employee Emergency Information NEI Intranet (Employees Only) *PDF files require ...

Increasing the Usage of Personal Protective Equipments in Constructing Subway Stations: An Application of Social Marketing Model

Directory of Open Access Journals (Sweden)

M Shams

2013-10-01

Full Text Available Abstract Background & aim: Although the relationship between the use of personal protective equipment and the reduction of workplace injuries is well-known the use of these devices during operation by the staff is not so desirable. This study was based on a model of social marketing interventions to increase the use of safety devices and personal protection on the subway-station staff. Methods: The present quasi-experimental study was based on the results of a formative research consisted of a qualitative (exploring employees’ views through focus group discussions and a quantitative study (measuring attitudes and behaviors by questionnaire and checklist. Based on the formative research findings, a free package includes a helmet with a label containing the message, an anti-cut safety gloves, a dust mask, and an educational pamphlet were delivered to intervention group. After four weeks, the check list of observational behaviors in two constructing stations was completed and the results were compared with before intervention. The data were analyzed by paired t-test, t-test and logistic regression. Results: Three common behaviors were observed among staff not using caps, masks and gloves. The odds ratio for helmet and mask usage in the intervention group was more than other groups. After the intervention, the use of safety helmets and masks significantly increased (p < 0.05. The odds ratio for the use of helmets and masks after intervention in the intervention group was significantly higher than other groups (p < 0.05. Conclusion: The experimental basis of the safety devices and personal protection needs and demands of the audience, material and immaterial costs of the equipment, supplies, and promoting their use in the right place, can encourage the staff to continuously use the safety devices at workplace. Key Words: Workplace, Injuries, Personal Protective Equipment, Social Marketing

Does helmet CPAP reduce cerebral blood flow and volume by comparison with Infant Flow driver CPAP in preterm neonates?

Science.gov (United States)

Zaramella, Patrizia; Freato, Federica; Grazzina, Nicoletta; Saraceni, Elisabetta; Vianello, Andrea; Chiandetti, Lino

2006-10-01

We compared neonatal helmet continuous positive airway pressure (CPAP) and the conventional nasal Infant Flow driver (IFD) CPAP in the noninvasive assessment of absolute cerebral blood flow (CBF) and relative cerebral blood volume changes (DeltaCBV) by near-infrared spectroscopy. A randomized crossover study in a tertiary referral NICU. Assessment of CBF and DeltaCBV in 17 very low birth weight infants with respiratory distress (median age 5 days) treated with two CPAP devices at a continuous distending pressure of 4 mbar. Neonates were studied for two consecutive 60-min periods with helmet CPAP and with IFD CPAP. Basal chromophore traces enabled DeltaCBV changes to be calculated. CBF was calculated in milliliters per 100 grams per minute from the saturation rise integral and rate of rise O(2)Hb-HHb. Median (range) CBF with helmet CPAP was 27.37 (9.47-48.20) vs. IFD CBF 34.74 (13.59-60.10)(p=0.049) and DeltaCBV 0.15 (0.09-0.28) with IFD and 0.13 (0.07-0.27) with helmet CPAP (NS). Using helmet and IFD CPAP, the neonates showed no difference in mean physiological parameters (transcutaneous carbon dioxide and oxygen tension, pulse oximetry saturation, heart rate, breathing rate, mean arterial blood pressure, desaturation rate, axillary temperature). Assessing CBF and DeltaCBV measured by near-infrared spectroscopy with two CPAP devices revealed no differences in relative blood volume, but CBF was lower with helmet CPAP. Greater active vasoconstriction and/or passive capillary and/or venous vessel compression seem the most likely reason, due to a positive pressure around the head, neck, and shoulders by comparison with the airway pressure.

The differences between storms driven by helmet streamer CIRs and storms driven by pseudostreamer CIRs

OpenAIRE

Borovsky, Joseph E.; Denton, Michael

2013-01-01

A corotating interaction region (CIR) is formed when fast coronal hole origin solar wind overtakes slow solar wind and forms a region of compressed plasma and magnetic field. The slow wind upstream of the coronal hole fast wind can be either of helmet streamer origin or pseudostreamer origin. For a collection of 125 CIR-driven geomagnetic storms, the slow wind ahead of each CIR is examined; for those storm not containing ejecta, each CIR is categorized as a helmet streamer CIR (74 of the 125 ...

Protective equipment and player characteristics associated with the incidence of sport-related concussion in high school football players: a multifactorial prospective study.

Science.gov (United States)

McGuine, Timothy A; Hetzel, Scott; McCrea, Michael; Brooks, M Alison

2014-10-01

The incidence of sport-related concussion (SRC) in high school football is well documented. However, limited prospective data are available regarding how player characteristics and protective equipment affect the incidence of SRC. To determine whether the type of protective equipment (helmet and mouth guard) and player characteristics affect the incidence of SRC in high school football players. Cohort study; Level of evidence, 2. Certified athletic trainers (ATs) at each high school recorded the type of helmet worn (brand, model, purchase year, and recondition status) by each player as well as information regarding players' demographics, type of mouth guard used, and history of SRC. The ATs also recorded the incidence and days lost from participation for each SRC. Incidence of SRC was compared for various helmets, type of mouth guard, history of SRC, and player demographics. A total of 2081 players (grades 9-12) enrolled during the 2012 and/or 2013 football seasons (2287 player-seasons) and participated in 134,437 football (practice or competition) exposures. Of these players, 206 (9%) sustained a total of 211 SRCs (1.56/1000 exposures). There was no difference in the incidence of SRC (number of helmets, % SRC [95% CI]) for players wearing Riddell (1171, 9.1% [7.6%-11.0%]), Schutt (680, 8.7% [6.7%-11.1%]), or Xenith (436, 9.2% [6.7%-12.4%]) helmets. Helmet age and recondition status did not affect the incidence of SRC. The rate of SRC (hazard ratio [HR]) was higher in players who wore a custom mouth guard (HR = 1.69 [95% CI, 1.20-2.37], P football players. Players who had sustained an SRC within the previous 12 months were more likely to sustain an SRC than were players without a history of SRC. Sports medicine providers who work with high school football players need to realize that factors other than the type of protective equipment worn affect the risk of SRC in high school players. © 2014 The Author(s).

Comparison of an in-helmet temperature monitor system to rectal temperature during exercise.

Science.gov (United States)

Wickwire, P Jason; Buresh, Robert J; Tis, Laurie L; Collins, Mitchell A; Jacobs, Robert D; Bell, Marla M

2012-01-01

Body temperature monitoring is crucial in helping to decrease the amount and severity of heat illnesses; however, a practical method of monitoring temperature is lacking. In response to the lack of a practical method of monitoring the temperature of athletes, Hothead Technologies developed a device (HOT), which continuously monitors an athlete's fluctuations in body temperature. HOT measures forehead temperature inside helmets. The purpose of this study was to compare HOT against rectal temperature (Trec). Male volunteers (n = 29, age = 23.5 ± 4.5 years, weight = 83.8 ± 10.4 kg, height = 180.1 ± 5.8 cm, body fat = 12.3 ± 4.5%) exercised on a treadmill at an intensity of 60-75% heart rate reserve (HRR) (wet bulb globe temperature [WBGT] = 28.7° C) until Trec reached 38.7° C. The correlation between Trec and HOT was 0.801 (R = 0.64, standard error of the estimate (SEE) = 0.25, p = 0.00). One reason for this relatively high correlation is the microclimate that HOT is monitoring. HOT is not affected by the external climate greatly because of its location in the helmet. Therefore, factors such as evaporation do not alter HOT temperature to a great degree. HOT was compared with Trec in a controlled setting, and the exercise used in this study was moderate aerobic exercise, very unlike that used in football. In a controlled laboratory setting, the relationship between HOT and Trec showed favorable correlations. However, in applied settings, helmets are repeatedly removed and replaced forcing HOT to equilibrate to forehead temperature every time the helmet is replaced. Therefore, future studies are needed to mimic how HOT will be used in field situations.

Influence of an Enforcement Campaign on Seat-Belt and Helmet Wearing, Karachi-Hala Highway, Pakistan

Science.gov (United States)

Bhatti, Junaid A.; Ejaz, Kiran; Razzak, Junaid A.; Tunio, Israr Ali; Sodhar, Irshad

2011-01-01

This study assessed to what extent an enforcement campaign influenced seat-belt and helmet wearing on a Pakistani highway. The study setting was the Karachi-Hala highway where a traffic enforcement campaign was conducted from Dec 2009 to Feb 2010. Seat-belt and helmet wearing were observed in Nov 2009 and Apr 2010 at Karachi toll plaza. Differences in wearing rates as a function of occupants’ age, sex, and vehicle type were compared between the two periods. On average, 9 119 (Standard deviation=1 896) traffic citations were issued per month from Aug 2009 to Feb 2010; 4.2% of which were for not wearing helmet. A 22.5% increase in citations was observed for Dec 2009 to Feb 2010 periods compared with Aug 2009 to Oct 2009 periods. Nearly six thousand four-wheeled and four hundred two-wheeled motorized vehicle occupants were observed in Nov 2009 and Apr 2010. Overall, two of the five drivers and one of the five front seat occupants wore seat belts. This proportion was significantly higher in drivers and front-seat occupants of cars than those of heavier vehicles. Similarly, one of two motorcyclists used a helmet but this proportion was 5.8% for pillion riders in Nov 2009. The increased enforcement had a limited influence on belt wearing in drivers (+4.0%; 95% Confidence Interval [95%CI]=1.8–6.1) and occupants (+6.2%; 95%CI=4.2–8.2). A higher increase was observed for motorcyclists (+9.8%; 95%CI=2.6–16.8) and pillion riders (+12.8%; 95%CI=5.4, 20.5). These results suggested that serious efforts are required to increase seat-belt and helmet use on Pakistani highways. Improving enforcement resources, increased fines, not allowing such vehicles on roads, and awareness campaigns targeting drivers of heavy vehicles might increase wearing rates in Pakistan. PMID:22105384

Protective garment ventilation system

Science.gov (United States)

Lang, R. (Inventor)

1970-01-01

A method and apparatus for ventilating a protective garment, space suit system, and/or pressure suits to maintain a comfortable and nontoxic atmosphere within is described. The direction of flow of a ventilating and purging gas in portions of the garment may be reversed in order to compensate for changes in environment and activity of the wearer. The entire flow of the ventilating gas can also be directed first to the helmet associated with the garment.

Material property determination of the lining layers of a versatile helmet

Directory of Open Access Journals (Sweden)

Kottner Radek

2018-01-01

Full Text Available This paper deals with material property identification of a helmet lining consisting of an outer layer of an expanded polystyrene (EPS and inner layer of an open-closed cell foam (OCCF. A combined numerical simulation and experimental testing was used for the material property identification. Compression and drop tests were performed. The ABAQUS finite element commercial code was used for numerical simulations in which the OOCF was modelled as a rate dependent viscoelastic material, while the EPS as a crushable foam. The reaction force time histories coming from the numerical simulation and the experiment have been used as a criterion for material parameter determination. After the identification of the material properties, numerical drop-tests were used to study the behaviour of a plate and a conical composite OOCF and EPS liners to decide which of them suits more for the helmet.

Determination of the 4 mm Gamma Knife helmet relative output factor using a variety of detectors

International Nuclear Information System (INIS)

Tsai, J.-S.; Rivard, Mark J.; Engler, Mark J.; Mignano, John E.; Wazer, David E.; Shucart, William A.

2003-01-01

Though the 4 mm Gamma Knife helmet is used routinely, there is disagreement in the Gamma Knife users community on the value of the 4 mm helmet relative output factor. A range of relative output factors is used, and this variation may impair observations of dose response and optimization of prescribed dose. To study this variation, measurements were performed using the following radiation detectors: silicon diode, diamond detector, radiographic film, radiochromic film, and TLD cubes. To facilitate positioning of the silicon diode and diamond detector, a three-dimensional translation micrometer was used to iteratively determine the position of maximum detector response. Positioning of the films and TLDs was accomplished by manufacturing custom holders for each technique. Results from all five measurement techniques indicate that the 4 mm helmet relative output factor is 0.868±0.014. Within the experimental uncertainties, this value is in good agreement with results obtained by other investigators using diverse techniques

Optimisation of energy absorbing liner for equestrian helmets. Part II: Functionally graded foam liner

International Nuclear Information System (INIS)

Cui, L.; Forero Rueda, M.A.; Gilchrist, M.D.

2009-01-01

The energy absorbing liner of safety helmets was optimised using finite element modelling. In this present paper, a functionally graded foam (FGF) liner was modelled, while keeping the average liner density the same as in a corresponding reference single uniform density liner model. Use of a functionally graded foam liner would eliminate issues regarding delamination and crack propagation between interfaces of different density layers which could arise in liners with discrete density variations. As in our companion Part I paper [Forero Rueda MA, Cui L, Gilchrist MD. Optimisation of energy absorbing liner for equestrian helmets. Part I: Layered foam liner. Mater Des [submitted for publication

Work of breathing using different interfaces in spontaneous positive pressure ventilation: helmet, face-mask, and endotracheal tube.

Science.gov (United States)

Oda, Shinya; Otaki, Kei; Yashima, Nozomi; Kurota, Misato; Matsushita, Sachiko; Kumasaka, Airi; Kurihara, Hutaba; Kawamae, Kaneyuki

2016-08-01

Noninvasive positive pressure ventilation (NPPV) using a helmet is expected to cause inspiratory trigger delay due to the large collapsible and compliant chamber. We compared the work of breathing (WOB) of NPPV using a helmet or a full face-mask with that of invasive ventilation by tracheal intubation. We used a lung model capable of simulating spontaneous breathing (LUNGOO; Air Water Inc., Japan). LUNGOO was set at compliance (C) = 50 mL/cmH2O and resistance (R) = 5 cmH2O/L/s for normal lung simulation, C = 20 mL/cmH2O and R = 5 cmH2O/L/s for restrictive lung, and C = 50 mL/cmH2O and R = 20 cmH2O/L/s for obstructive lung. Muscle pressure was fixed at 25 cmH2O and respiratory rate at 20 bpm. Pressure support ventilation and continuous positive airway pressure were performed with each interface placed on a dummy head made of reinforced plastic that was connected to LUNGOO. We tested the inspiratory WOB difference between the interfaces with various combinations of ventilator settings (positive end-expiratory pressure 5 cmH2O; pressure support 0, 5, and 10 cmH2O). In the normal lung and restrictive lung models, WOB decreased more with the face-mask than the helmet, especially when accompanied by the level of pressure support. In the obstructive lung model, WOB with the helmet decreased compared with the other two interfaces. In the mixed lung model, there were no significant differences in WOB between the three interfaces. NPPV using a helmet is more effective than the other interfaces for WOB in obstructive lung disease.

Sonographic Analysis of Changes in Skull Shape After Cranial Molding Helmet Therapy in Infants With Deformational Plagiocephaly.

Science.gov (United States)

Kwon, Dong Rak

2016-04-01

-The purpose of this study was to investigate the changes in skull shape on sonography after cranial molding helmet therapy in infants with deformational plagiocephaly. -Twenty-six infants who were treated with cranial molding helmet therapy were recruited. Caliper and sonographic measurements were performed. The lateral length of the affected and unaffected sides of the skull and cranial vault asymmetry index were measured with calipers. The occipital angle, defined as the angle between lines projected along the lambdoid sutures of the skull, was calculated by sonography. The occipital angle difference and occipital angle ratio were also measured. All caliper and sonographic measurements were performed in each infant twice before and twice after treatment. -The study group included 12 male and 14 female infants with a mean age ± SD of 6.2 ± 3.5 months. The mean treatment duration was 6.0 ± 2.5 months. The difference in lateral length before and after helmet therapy was significantly greater on the affected skull than the unaffected skull (16.7 ± 12.7 versus 9.0 ± 13.4 mm; P skull than the unaffected skull (-5.7° ± 7.3° versus 4.2° ± 7.9°; P < .01). The cranial vault asymmetry index and occipital angle ratio were significantly reduced after helmet therapy (cranial vault asymmetry index, 9.3% ± 2.3% versus 3.5% ± 3.0%; occipital angle ratio, 1.07 ± 0.05 versus 1.01 ± 0.01; P < .05). -These results suggest that occipital angle measurements using sonography, combined with cephalometry, could provide a better understanding of the therapeutic effects of cranial molding helmet therapy in infants with deformational plagiocephaly. © 2016 by the American Institute of Ultrasound in Medicine.

A fractionation of the physiological burden of the personal protective equipment worn by firefighters.

Science.gov (United States)

Taylor, Nigel A S; Lewis, Michael C; Notley, Sean R; Peoples, Gregory E

2012-08-01

Load carriage increases physiological strain, reduces work capacity and elevates the risk of work-related injury. In this project, the separate and combined physiological consequences of wearing the personal protective equipment used by firefighters were evaluated. The overall impact upon performance was first measured in 20 subjects during a maximal, job-related obstacle course trial and an incremental treadmill test to exhaustion (with and without protective equipment). The fractional contributions of the thermal protective clothing, helmet, breathing apparatus and boots were then separately determined during steady-state walking (4.8 km h(-1), 0% gradient) and bench stepping (20 cm at 40 steps min(-1)). The protective equipment reduced exercise tolerance by 56% on a treadmill, with the ambulatory oxygen consumption reserve (peak minus steady-state walking) being 31% lower. For the obstacle course, performance declined by 27%. Under steady-state conditions, the footwear exerted the greatest relative metabolic impact during walking and bench stepping, being 8.7 and 6.4 times greater per unit mass than the breathing apparatus. Indeed, the relative influence of the clothing on oxygen cost was at least three times that of the breathing apparatus. Therefore, the most efficient way to reduce the physiological burden of firefighters' protective equipment, and thereby increase safety, would be to reduce the mass of the boots and thermal protective clothing.

Effects of videogame distraction and a virtual reality type head-mounted display helmet on cold pressor pain in young elementary school-aged children.

Science.gov (United States)

Dahlquist, Lynnda M; Weiss, Karen E; Law, Emily F; Sil, Soumitri; Herbert, Linda Jones; Horn, Susan Berrin; Wohlheiter, Karen; Ackerman, Claire Sonntag

2010-07-01

This study examined the effects of videogame distraction and a virtual reality (VR) type head-mounted display helmet for children undergoing cold pressor pain. Fifty children between the ages of 6 and 10 years underwent a baseline cold pressor trial followed by two cold pressor trials in which interactive videogame distraction was delivered via a VR helmet or without a VR helmet in counterbalanced order. As expected, children demonstrated significant improvements in pain threshold and pain tolerance during both distraction conditions. However, the two distraction conditions did not differ in effectiveness. Using the VR helmet did not result in improved pain tolerance over and above the effects of interactive videogame distraction without VR technology. Clinical implications and possible developmental differences in elementary school-aged children's ability to use VR technology are discussed.

Socioeconomic Inequalities in Nonuse of Seatbelts in Cars and Helmets on Motorcycles among People Living in Kurdistan Province, Iran.

Science.gov (United States)

Moradi, Ghobad; Malekafzali Ardakani, Hossein; Majdzadeh, Reza; Bidarpour, Farzam; Mohammad, Kazem; Holakouie-Naieni, Kourosh

2014-09-01

The aim of this study was to determine the socioeconomic inequalities in nonuse of seatbelts in cars and helmets on motorcycles in Kurdistan Province, west of Iran, 2009. The data used in this study was collected from the data gathered in non-communicable disease surveillance system (NCDSS) in 2009 in Kurdistan. A total of 1000 people were included in this study. The outcome variable of this study was the nonuse of seatbelts and helmets. The socio-economic status (SES) was calculated based on participants' residential area and assets using Principal Component Analysis (PCA) method. The concentration index, concentration curve, and comparison of Odds Ratio (OR) in different SES groups were used to measure the socioeconomic inequalities using logistic regression. In order to determine the contribution of determinants of inequality, decomposition analysis was used. The prevalence of nonuse of seatbelts in cars and helmets on motorcycles were 47.5%, 95%CI [44%, 55%], respectively. The Concentration index was -0.097, CI [-0.148, -0.046]. The OR of nonuse of seatbelts in cars and helmets on motorcycles in the richest group compared with the poorest group was 0.39, 95%CI [0.23, 0.68]. The results of the decomposition analysis showed that 34% of inequalities were due to SES, 47% were due to residential area, and 12% were due to unknown factors. There is a reverse association between SES and nonuse of seatbelts in cars and helmets on motorcycles. This issue must be considered while planning to reduce traffic accidents injuries.

Investigation of the optimal detector arrangement for the helmet-chin PET – A simulation study

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Abdella M., E-mail: abdellanur@gmail.com; Tashima, Hideaki; Yoshida, Eiji; Yamaya, Taiga, E-mail: yamaya.taiga@qst.go.jp

2017-06-21

High sensitivity and high spatial resolution dedicated brain PET scanners are in high demand for early diagnosis of neurodegenerative diseases and studies of brain functions. To meet the demand, we have proposed the helmet-chin PET geometry which has a helmet detector and a chin detector. Our first prototype scanner used 54 4-layer depth-of-interaction (DOI) detectors. The helmet detector of the scanner had three detector rings with different radii arranged on a surface of a hemisphere (with a radius of 126.5 mm) and a top cover detector. Therefore, in this study, for our next development, we propose a spherical arrangement, in which the central axis of each detector points toward the center of the hemisphere, and we optimize the size of the detector crystal block to be arranged on the helmet detector. We simulate the spherical arrangement with the optimized crystal block size and compare its imaging performance with the multi-ring arrangement, which has a similar detector arrangement to that of our first prototype. We conduct Monte Carlo simulation to model the scanners having the 4-layer DOI detectors which consist of LYSO crystals. A dead space of 2 mm is assumed on each side of the crystal blocks such as for wrapping. The size of the crystal block is varied from 4×4 mm{sup 2} to 54×54 mm{sup 2} while fixing the thickness of the crystal block to 20 mm. We find that the crystal block sized at 42×42 mm{sup 2} has the highest sensitivity for a hemispherical phantom. The comparison of the two arrangements with the optimized crystal blocks show that, for the same number of crystal blocks, the spherical arrangement has 17% higher sensitivity for the hemispherical phantom than the multi-ring arrangement. We conclude that the helmet-chin PET with the spherical arrangement constructed from the crystal block sized at 42×42×20 mm{sup 3} has better imaging performance especially at the upper part of the brain compared to the multi-ring arrangement while keeping similar

Plasma processing of fibre materials for enhanced impact protection

NARCIS (Netherlands)

Creyghton, Y.L.M.; Simor, M.

2009-01-01

The performance of lightweight impact protective clothing depends on the constituting materials, their assembly in a system and interaction under various dynamic impact conditions. In this paper an overview of options for improved impact protective clothing systems based on a new plasma technology

Predicting bicycle helmet stage-of-change among middle school, high school, and college cyclists from demographic, cognitive, and motivational variables.

Science.gov (United States)

Weiss, Jeffrey; Okun, Morris; Quay, Nancy

2004-09-01

To apply Prochaska's Transtheoretical model of behavior change to bicycle helmet use among middle school, high school, and college students. A battery of questionnaires was administered to cyclists in the seventh and ninth grades and to college students in Phoenix, Arizona (N=797). The battery included: (1) a question to determine respondent's stage of behavior change in Prochaska's Transtheoretical model; (2) items assessing the perceived pros and cons of helmet use; (3) a bicycle safety knowledge test; and (4) demographic information. Forty-three percent of the students were in "Precontemplation," 17% were in either "Contemplation" or "Preparation," 16% were in either "Action" or "Maintenance," and 24% were in the "Relapse" stage of change. Grade, Sex, Knowledge, Pros, and Cons, and the Grade by sex and the Grade by knowledge interactions were significant predictors of helmet use stages. Compared with students in Precontemplation, students in the Contemplation stage were disproportionately younger and had higher Pro scores, lower Con scores, and more knowledge (except in the ninth grade). The Transtheoretical model of behavior change is a viable theoretical framework for designing interventions aimed at increasing bicycle helmet use in children and adolescents.

Analysis of linear head accelerations from collegiate football impacts.

Science.gov (United States)

Brolinson, P Gunnar; Manoogian, Sarah; McNeely, David; Goforth, Mike; Greenwald, Richard; Duma, Stefan

2006-02-01

Sports-related concussions result in 300,000 brain injuries in the United States each year. We conducted a study utilizing an in-helmet system that measures and records linear head accelerations to analyze head impacts in collegiate football. The Head Impact Telemetry (HIT) System is an in-helmet system with six spring-mounted accelerometers and an antenna that transmits data via radio frequency to a sideline receiver and laptop computer system. A total of 11,604 head impacts were recorded from the Virginia Tech football team throughout the 2003 and 2004 football seasons during 22 games and 62 practices from a total of 52 players. Although the incidence of injury data are limited, this study presents an extremely large data set from human head impacts that provides valuable insight into the lower limits of head acceleration that cause mild traumatic brain injuries.

Cognitive considerations for helmet-mounted display design

Science.gov (United States)

Francis, Gregory; Rash, Clarence E.

2010-04-01

Helmet-mounted displays (HMDs) are designed as a tool to increase performance. To achieve this, there must be an accurate transfer of information from the HMD to the user. Ideally, an HMD would be designed to accommodate the abilities and limitations of users' cognitive processes. It is not enough for the information (whether visual, auditory, or tactual) to be displayed; the information must be perceived, attended, remembered, and organized in a way that guides appropriate decision-making, judgment, and action. Following a general overview, specific subtopics of cognition, including perception, attention, memory, knowledge, decision-making, and problem solving are explored within the context of HMDs.

Effects of Videogame Distraction using a Virtual Reality Type Head-Mounted Display Helmet on Cold Pressor Pain in Children

OpenAIRE

Dahlquist, Lynnda M.; Weiss, Karen E.; Dillinger Clendaniel, Lindsay; Law, Emily F.; Ackerman, Claire Sonntag; McKenna, Kristine D.

2008-01-01

Objective To test whether a head-mounted display helmet enhances the effectiveness of videogame distraction for children experiencing cold pressor pain. Method Forty-one children, aged 6–14 years, underwent one or two baseline cold pressor trials followed by two distraction trials in which they played the same videogame with and without the helmet in counterbalanced order. Pain threshold (elapsed time until the child reported pain) and pain tolerance (total time the child kept the hand submer...

Effects of videogame distraction using a virtual reality type head-mounted display helmet on cold pressor pain in children.

Science.gov (United States)

Dahlquist, Lynnda M; Weiss, Karen E; Clendaniel, Lindsay Dillinger; Law, Emily F; Ackerman, Claire Sonntag; McKenna, Kristine D

2009-06-01

To test whether a head-mounted display helmet enhances the effectiveness of videogame distraction for children experiencing cold pressor pain. Forty-one children, aged 6-14 years, underwent one or two baseline cold pressor trials followed by two distraction trials in which they played the same videogame with and without the helmet in counterbalanced order. Pain threshold (elapsed time until the child reported pain) and pain tolerance (total time the child kept the hand submerged in the cold water) were measured for each cold pressor trial. Both distraction conditions resulted in improved pain tolerance relative to baseline. Older children appeared to experience additional benefits from using the helmet, whereas younger children benefited equally from both conditions. The findings suggest that virtual reality technology can enhance the effects of distraction for some children. Research is needed to identify the characteristics of children for whom this technology is best suited.

Full-color wide field-of-view holographic helmet-mounted display for pilot/vehicle interface development and human factors studies

Science.gov (United States)

Burley, James R., II; LaRussa, Joseph A.

1990-10-01

A Helmet-Mounted Display (HMD) which utilizes highly efficient trichromatic holographic elements has been designed to support pilot vechicle interface development and human factors studies at the NASA-Langley Research Center. While the optics are fully color corrected, the miniature CRT's are monochromatic. This design provides an upgrade path to full-color when miniature display technology matures to color. The optical design conforms to the helmet shape and provides a 50 degree field-of-view (FOV) to each eye. Built-in adjustments allow each ocular to be independently moved so that the overall horizontal FOV may be varied from 50 degrees to 100 degrees with a corresponding change in the stereo overlap region. The helmet design and interpupillary adjustment allow for the 5th through 95th percentile male and female wearer. Total head-borne weight is approximately 4.2 pounds. The high-resolution monochromatic CRTs are driven by a set of multisync electronics with a maximum video bandwidth of 88 Mhz and supports bith raster and stroke modes. The electronics are designed to be compatiable with the Silicon Graphics IRIS 4D graphics workstations and the ADAGE 340 stroke graphics computer. A Polhemus magnetic tracking device is used to determine the helmet line-of-sight. The helmet will be used to develop innovative new display concepts for the F- 1 8 High-Alpha Research Vehicle (HARV) which make use of the unique display properties of the HMD. Pictorial displays, which convey the appropriate information intuitively, are envisioned. Human factors studies are also planned to evaluate the utility of stereopsis and determine the FOV requirements for different tasks. Concepts proven in the simulator will be carried to flight test in 1993 with a lighter weight, "hardened" version of this HMD design.

Neutron and X-ray characterisation of the metallurgical properties of a 7th century BC Corinthian-type bronze helmet

Science.gov (United States)

Pantos, E.; Kockelmann, W.; Chapon, L. C.; Lutterotti, L.; Bennet, S. L.; Tobin, M. J.; Mosselmans, J. F. W.; Pradell, T.; Salvado, N.; Butí, S.; Garner, R.; Prag, A. J. N. W.

2005-09-01

Neutron and synchrotron X-ray diffraction, X-ray fluorescence and FTIR were used to examine a Corinthian-type bronze helmet which is now on display at The Manchester Museum, UK. This type of helmet was manufactured out of a single piece of bronze, probably on a rod-anvil, and like all body-armour it was made to measure. Neutron diffraction sampling of the bronze volume in different areas was used to study the composition, microstructure and crystallographic texture of the alloy in order to draw conclusions about the manufacturing processes. The neutron data revealed the presence of microstrains and non-random distributions of bronze grains hinting at annealing-hammering working cycles in order to harden and shape the alloy. X-ray fluorescence showed that the main body of the helmet is a copper-tin alloy, while the noseguard contains zinc in high abundance. This key compositional difference confirms that the noseguard is not the original but is a modern substitute fabricated for restoration purposes. SR XRD and FTIR from several spots on the head and noseguard identified several surface corrosion products and showed a variation of the Cu-Sn or Cu-Zn percentage compositions, and of the mineral phases. Small samples of corrosion flakes extracted from the outside and inside of the helmet were used to obtain powder XRD patterns.

Spectrum of acute clinical characteristics of diagnosed concussions in college athletes wearing instrumented helmets: clinical article.

Science.gov (United States)

Duhaime, Ann-Christine; Beckwith, Jonathan G; Maerlender, Arthur C; McAllister, Thomas W; Crisco, Joseph J; Duma, Stefan M; Brolinson, P Gunnar; Rowson, Steven; Flashman, Laura A; Chu, Jeffrey J; Greenwald, Richard M

2012-12-01

Concussive head injuries have received much attention in the medical and public arenas, as concerns have been raised about the potential short- and long-term consequences of injuries sustained in sports and other activities. While many student athletes have required evaluation after concussion, the exact definition of concussion has varied among disciplines and over time. The authors used data gathered as part of a multiinstitutional longitudinal study of the biomechanics of head impacts in helmeted collegiate athletes to characterize what signs, symptoms, and clinical histories were used to designate players as having sustained concussions. Players on 3 college football teams and 4 ice hockey teams (male and female) wore helmets instrumented with Head Impact Telemetry (HIT) technology during practices and games over 2-4 seasons of play. Preseason clinical screening batteries assessed baseline cognition and reported symptoms. If a concussion was diagnosed by the team medical staff, basic descriptive information was collected at presentation, and concussed players were reevaluated serially. The specific symptoms or findings associated with the diagnosis of acute concussion, relation to specific impact events, timing of symptom onset and diagnosis, and recorded biomechanical parameters were analyzed. Data were collected from 450 athletes with 486,594 recorded head impacts. Forty-eight separate concussions were diagnosed in 44 individual players. Mental clouding, headache, and dizziness were the most common presenting symptoms. Thirty-one diagnosed cases were associated with an identified impact event; in 17 cases no specific impact event was identified. Onset of symptoms was immediate in 24 players, delayed in 11, and unspecified in 13. In 8 cases the diagnosis was made immediately after a head impact, but in most cases the diagnosis was delayed (median 17 hours). One diagnosed concussion involved a 30-second loss of consciousness; all other players retained

Effects of Videogame Distraction using a Virtual Reality Type Head-Mounted Display Helmet on Cold Pressor Pain in Children

Science.gov (United States)

Weiss, Karen E.; Dillinger Clendaniel, Lindsay; Law, Emily F.; Ackerman, Claire Sonntag; McKenna, Kristine D.

2009-01-01

Objective To test whether a head-mounted display helmet enhances the effectiveness of videogame distraction for children experiencing cold pressor pain. Method Forty-one children, aged 6–14 years, underwent one or two baseline cold pressor trials followed by two distraction trials in which they played the same videogame with and without the helmet in counterbalanced order. Pain threshold (elapsed time until the child reported pain) and pain tolerance (total time the child kept the hand submerged in the cold water) were measured for each cold pressor trial. Results Both distraction conditions resulted in improved pain tolerance relative to baseline. Older children appeared to experience additional benefits from using the helmet, whereas younger children benefited equally from both conditions. The findings suggest that virtual reality technology can enhance the effects of distraction for some children. Research is needed to identify the characteristics of children for whom this technology is best suited. PMID:18367495

46 CFR 169.717 - Fireman's outfit.

Science.gov (United States)

2010-10-01

... helmet that provides effective protection against impact; and (8) Protective clothing. (b) Each vessel... 46 Shipping 7 2010-10-01 2010-10-01 false Fireman's outfit. 169.717 Section 169.717 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel...

Successful Removal of Football Helmet Face-Mask Clips After 1 Season of Use

Science.gov (United States)

Scibek, Jason S.; Gatti, Joseph M.; McKenzie, Jennifer I.

2012-01-01

Context Whereas many researchers have assessed the ability to remove loop straps in traditional face-mask attachment systems after at least 1 season of use, research in which the effectiveness of the Riddell Quick Release (QR) Face Guard Attachment System clip after 1 season has been assessed is limited. Objective To examine the success rate of removing the QR clips after 1 season of use at the Football Championship Subdivision level. We hypothesized that 1 season of use would negatively affect the removal rate of the QR clip but repeated clip-removal trials would improve the removal rate. Design Retrospective, quasi-experimental design. Setting Controlled laboratory study. Patients or Other Participants Sixty-three football helmets from a National Collegiate Athletic Association Division I university located in western Pennsylvania used during the 2008 season were tested. Intervention(s) Three certified athletic trainers (2 men, 1 woman; age = 31.3 ± 3.06 years, time certified = 9.42 ± 2.65 years) attempted to remove the QR clips from each helmet with the tool provided by the manufacturer. Helmets then were reassembled to allow each athletic trainer to attempt clip removal. Main Outcome Measure(s) The dependent variables were total left clips removed (TCR-L), total right clips removed (TCR-R), and total clips removed (TCR). Success rate of clip removal (SRCR) also was assessed. Results Percentages for TCR-L, TCR-R, and TCR were 100% (189 of 189), 96.30% (182 of 189), and 98.15% (371 of 378), respectively. A paired-samples t test revealed a difference between TCR-R and TCR-L (t188 = −2.689, P = .008, μd = 0.037, 95% confidence interval [CI] = −0.064, −0.010). The percentage for SRCR was 96.30% (n = 182), whereas SRCR percentages for trials 1, 2, and 3 were 95.24% (n = 60), 98.41% (n = 62), and 95.24% (n = 60), respectively, and did not represent a difference (F2,186 = 0.588, P = .56, 95% CI = 0.94, 0.99). Conclusions Our results indicated favorable and

Louisiana motorcycle fatalities in the wake of governmentally implemented change: a retrospective analysis of the motorcycle morbidity and mortality before, during, and after the repeal of a statewide helmet mandate.

Science.gov (United States)

Strom, Shane F; Ambekar, Sudheer; Madhugiri, Venkatesh S; Nanda, Anil

2013-06-01

On August 15, 2004, Louisiana's universal motorcycle helmet mandate was reinstated. Previous studies have shown that mortality and morbidity of motorcycle riders who crashed had increased during the 5 years the mandate was repealed. The objective of this study was to discern whether the reinstatement of the universal helmet mandate has resulted in a subsequent decrease in motorcycle-related mortality and morbidity in the state of Louisiana. A retrospective analysis was performed observing the regularity of helmet use and the associated morbidity and mortality of motorcycle traffic accidents from the time before, during, and after the universal motorcycle helmet mandate was repealed in the state of Louisiana. Fatality statistics were obtained through the National Highway Safety Traffic Association. Injury, helmet use, and collision data were obtained from the Louisiana Highway Safety Commission. Motorcycle registration data were obtained from the Federal Highway Administration. Motorcycle crash-related fatalities increased significantly when the statewide helmet mandate was repealed, and interestingly, after reinstatement, these fatality rates never returned to their previous lows. Motorcycle fatalities have increased out of proportion to the increase in motorbike registrations, even when yearly fatalities are normalized to fatalities per 10,000 registered bikes. An all-time high in fatalities was seen in 2006, a year subsequent to the mandate's reinstatement. Fatalities per collision were elevated significantly after the mandate's repeal but did not return to prerepeal lows after the mandate's reinstatement. Although helmet use after reinstatement has reached all-time highs, fatality rates have remained elevated since the original mandate repeal in 1999. Other achievable changes in state policy and law enforcement should be explored to quell this heightened risk to motorcycle enthusiasts in Louisiana, and states considering changing their own motorcycle helmet

Implications of heterogeneous impacts of protected areas on deforestation and poverty.

Science.gov (United States)

Hanauer, Merlin M; Canavire-Bacarreza, Gustavo

2015-11-05

Protected areas are a popular policy instrument in the global fight against loss of biodiversity and ecosystem services. However, the effectiveness of protected areas in preventing deforestation, and their impacts on poverty, are not well understood. Recent studies have found that Bolivia's protected-area system, on average, reduced deforestation and poverty. We implement several non-parametric and semi-parametric econometric estimators to characterize the heterogeneity in Bolivia's protected-area impacts on joint deforestation and poverty outcomes across a number of socioeconomic and biophysical moderators. Like previous studies from Costa Rica and Thailand, we find that Bolivia's protected areas are not associated with poverty traps. Our results also indicate that protection did not have a differential impact on indigenous populations. However, results from new multidimensional non-parametric estimators provide evidence that the biophysical characteristics associated with the greatest avoided deforestation are the characteristics associated with the potential for poverty exacerbation from protection. We demonstrate that these results would not be identified using the methods implemented in previous studies. Thus, this study provides valuable practical information on the impacts of Bolivia's protected areas for conservation practitioners and demonstrates methods that are likely to be valuable to researchers interested in better understanding the heterogeneity in conservation impacts. © 2015 The Author(s).

29 CFR Appendix B to Subpart I to... - Non-mandatory Compliance Guidelines for Hazard Assessment and Personal Protective Equipment...

Science.gov (United States)

2010-07-01

... velocities, masses, projectile shape, radiation intensities, with the capabilities of the available... selecting head protection, knowledge of potential electrical hazards is important. Class A helmets, in... required, the duration, frequency, and degree of exposure of the hazard, and the physical stresses that...

Emergency Face-Mask Removal Effectiveness: A Comparison of Traditional and Nontraditional Football Helmet Face-Mask Attachment Systems

Science.gov (United States)

Swartz, Erik E.; Belmore, Keith; Decoster, Laura C.; Armstrong, Charles W.

2010-01-01

Abstract Context: Football helmet face-mask attachment design changes might affect the effectiveness of face-mask removal. Objective: To compare the efficiency of face-mask removal between newly designed and traditional football helmets. Design: Controlled laboratory study. Setting: Applied biomechanics laboratory. Participants: Twenty-five certified athletic trainers. Intervention(s): The independent variable was face-mask attachment system on 5 levels: (1) Revolution IQ with Quick Release (QR), (2) Revolution IQ with Quick Release hardware altered (QRAlt), (3) traditional (Trad), (4) traditional with hardware altered (TradAlt), and (5) ION 4D (ION). Participants removed face masks using a cordless screwdriver with a back-up cutting tool or only the cutting tool for the ION. Investigators altered face-mask hardware to unexpectedly challenge participants during removal for traditional and Revolution IQ helmets. Participants completed each condition twice in random order and were blinded to hardware alteration. Main Outcome Measure(s): Removal success, removal time, helmet motion, and rating of perceived exertion (RPE). Time and 3-dimensional helmet motion were recorded. If the face mask remained attached at 3 minutes, the trial was categorized as unsuccessful. Participants rated each trial for level of difficulty (RPE). We used repeated-measures analyses of variance (α  =  .05) with follow-up comparisons to test for differences. Results: Removal success was 100% (48 of 48) for QR, Trad, and ION; 97.9% (47 of 48) for TradAlt; and 72.9% (35 of 48) for QRAlt. Differences in time for face-mask removal were detected (F4,20  =  48.87, P  =  .001), with times ranging from 33.96 ± 14.14 seconds for QR to 99.22 ± 20.53 seconds for QRAlt. Differences were found in range of motion during face-mask removal (F4,20  =  16.25, P  =  .001), with range of motion from 10.10° ± 3.07° for QR to 16.91° ± 5.36° for TradAlt. Differences also were detected

Emergency face-mask removal effectiveness: a comparison of traditional and nontraditional football helmet face-mask attachment systems.

Science.gov (United States)

Swartz, Erik E; Belmore, Keith; Decoster, Laura C; Armstrong, Charles W

2010-01-01

Football helmet face-mask attachment design changes might affect the effectiveness of face-mask removal. To compare the efficiency of face-mask removal between newly designed and traditional football helmets. Controlled laboratory study. Applied biomechanics laboratory. Twenty-five certified athletic trainers. The independent variable was face-mask attachment system on 5 levels: (1) Revolution IQ with Quick Release (QR), (2) Revolution IQ with Quick Release hardware altered (QRAlt), (3) traditional (Trad), (4) traditional with hardware altered (TradAlt), and (5) ION 4D (ION). Participants removed face masks using a cordless screwdriver with a back-up cutting tool or only the cutting tool for the ION. Investigators altered face-mask hardware to unexpectedly challenge participants during removal for traditional and Revolution IQ helmets. Participants completed each condition twice in random order and were blinded to hardware alteration. Removal success, removal time, helmet motion, and rating of perceived exertion (RPE). Time and 3-dimensional helmet motion were recorded. If the face mask remained attached at 3 minutes, the trial was categorized as unsuccessful. Participants rated each trial for level of difficulty (RPE). We used repeated-measures analyses of variance (α  =  .05) with follow-up comparisons to test for differences. Removal success was 100% (48 of 48) for QR, Trad, and ION; 97.9% (47 of 48) for TradAlt; and 72.9% (35 of 48) for QRAlt. Differences in time for face-mask removal were detected (F(4,20)  =  48.87, P  =  .001), with times ranging from 33.96 ± 14.14 seconds for QR to 99.22 ± 20.53 seconds for QRAlt. Differences were found in range of motion during face-mask removal (F(4,20)  =  16.25, P  =  .001), with range of motion from 10.10° ± 3.07° for QR to 16.91° ± 5.36° for TradAlt. Differences also were detected in RPE during face-mask removal (F(4,20)  =  43.20, P  =  .001), with participants reporting average

The motivational safety helmet : Redesign suggestions improving the intrinsic motivation of construction site workers

NARCIS (Netherlands)

Beldman, T. (Teunis); Boer, de J. (Johannes); Lemmens, P. (Pim); Stilma, M. (Margot)

2014-01-01

In reaction to the lack of intrinsic motivation of construction site workers, to wear their safety helmets at all times, a series of research projects studied causes and possible solutions. Goal is to gain an inspirational discussion to get the design onto the next level. This paper describes a

Use of protective equipment by adolescents in inline skating, skateboarding, and snowboarding.

Science.gov (United States)

Kroncke, Erica L; Niedfeldt, Mark W; Young, Craig C

2008-01-01

Determine the frequency of personal protective equipment (PPE) use in adolescent inline skaters, skateboarders, and snowboarders; explore factors influencing PPE use; identify factors that would influence use; and examine the association of high-risk behaviors and PPE use. Cross-sectional survey. Central/southeast Wisconsin. Participants 13-18 years-old. None. Independent variables = age, gender, sport. None. Dependent variables = PPE use, factors influencing use, and frequency of other high-risk behaviors. The mean age of 333 participiants was 14.9 years. Adolescents wore considerably less PPE than recommended. Inline skaters wore the most; snowboarders the least. The most common reasons adolescents wore PPE were parents, peers, and rule/requirement. Younger adolescents cited parents more often than older adolescents as a factor for PPE use. Discomfort and lack of perceived need were the most common reasons for nonuse. Sustaining/witnessing an accident was the most common reason that would convince adolescents to wear PPE. Almost half of adolescents reported nothing would convince them to wear PPE. Younger adolescents wore more PPE than older adolescents. An association was seen between PPE use in all sports and bicycle helmets. An inverse relationship was found for tobacco and helmet use among skaters, as well as alcohol and helmet use in skateboarders. Adolescents underuse PPE. PPE reinforcement by parents/peers, encouraging bike helmets, manufacturing more comfortable gear, educating adolescents, and instituting PPE requirements in public areas may increase compliance. This could lead to decreased injuries. Physicians should discuss PPE with their patients/families. There may be an association between PPE use in extreme sports and decreased high-risk health behaviors.

Effect of impact surface in equestrian falls

OpenAIRE

Clark, J. Michio; Post, Andrew; Connor, Thomas A.; Hoshizaki, Thomas Blaine; Gilchrist, M. D.

2016-01-01

This study examines the effect of impact surface on head kinematic response and maximum principal strain (MPS) for equestrian falls. A helmeted Hybrid III headform was dropped unrestrained onto three impact surfaces of different stiffness (steel, turf and sand) and three locations. Peak resultant linear acceleration, rotational acceleration and duration of the impact events were measured. A finite element brain model was used to calculate MPS. The results revealed that drops onto steel produc...

Helmet-mounted displays: why haven't they taken off?

Science.gov (United States)

Havig, P.; Goff, C.; McIntire, J.; Franck, D.

2009-05-01

Helmet-Mounted Display (HMD) technologies have been developing for over 3 decades and have been studied for multiple applications ranging from military aircraft, to virtual reality, augmented reality, entertainment and a host of other ideas. It would not be unreasonable to assume that after this much time they would be employed in our daily lives as ubiquitously as the common desktop monitor. However, this is simply not the case. How can this be when they can be used in so many ways for so many tasks? Throughout this work we will look at some of the reasons why as well of some of the ways they can be used.

International funding agencies: potential leaders of impact evaluation in protected areas?

Science.gov (United States)

Craigie, Ian D; Barnes, Megan D; Geldmann, Jonas; Woodley, Stephen

2015-11-05

Globally, protected areas are the most commonly used tools to halt biodiversity loss. Yet, some are failing to adequately conserve the biodiversity they contain. There is an urgent need for knowledge on how to make them function more effectively. Impact evaluation methods provide a set of tools that could yield this knowledge. However, rigorous outcome-focused impact evaluation is not yet used as extensively as it could be in protected area management. We examine the role of international protected area funding agencies in facilitating the use of impact evaluation. These agencies are influential stakeholders as they allocate hundreds of millions of dollars annually to support protected areas, creating a unique opportunity to shape how the conservation funds are spent globally. We identify key barriers to the use of impact evaluation, detail how large funders are uniquely placed to overcome many of these, and highlight the potential benefits if impact evaluation is used more extensively. © 2015 The Author(s).

Advanced Helmet Mounted Display (AHMD) for simulator applications

Science.gov (United States)

Sisodia, Ashok; Riser, Andrew; Bayer, Michael; McGuire, James P.

2006-05-01

The Advanced Helmet Mounted Display (AHMD), augmented reality visual system first presented at last year's Cockpit and Future Displays for Defense and Security conference, has now been evaluated in a number of military simulator applications and by L-3 Link Simulation and Training. This paper presents the preliminary results of these evaluations and describes current and future simulator and training applications for HMD technology. The AHMD blends computer-generated data (symbology, synthetic imagery, enhanced imagery) with the actual and simulated visible environment. The AHMD is designed specifically for highly mobile deployable, minimum resource demanding reconfigurable virtual training systems to satisfy the military's in-theater warrior readiness objective. A description of the innovative AHMD system and future enhancements will be discussed.

Digital Image Processing Overview For Helmet Mounted Displays

Science.gov (United States)

Parise, Michael J.

1989-09-01

Digital image processing provides a means to manipulate an image and presents a user with a variety of display formats that are not available in the analog image processing environment. When performed in real time and presented on a Helmet Mounted Display, system capability and flexibility are greatly enhanced. The information content of a display can be increased by the addition of real time insets and static windows from secondary sensor sources, near real time 3-D imaging from a single sensor can be achieved, graphical information can be added, and enhancement techniques can be employed. Such increased functionality is generating a considerable amount of interest in the military and commercial markets. This paper discusses some of these image processing techniques and their applications.

Reassessing the forest impacts of protection: the challenge of nonrandom location and a corrective method.

Science.gov (United States)

Joppa, Lucas; Pfaff, Alexander

2010-01-01

Protected areas are leading tools in efforts to slow global species loss and appear also to have a role in climate change policy. Understanding their impacts on deforestation informs environmental policies. We review several approaches to evaluating protection's impact on deforestation, given three hurdles to empirical evaluation, and note that "matching" techniques from economic impact evaluation address those hurdles. The central hurdle derives from the fact that protected areas are distributed nonrandomly across landscapes. Nonrandom location can be intentional, and for good reasons, including biological and political ones. Yet even so, when protected areas are biased in their locations toward less-threatened areas, many methods for impact evaluation will overestimate protection's effect. The use of matching techniques allows one to control for known landscape biases when inferring the impact of protection. Applications of matching have revealed considerably lower impact estimates of forest protection than produced by other methods. A reduction in the estimated impact from existing parks does not suggest, however, that protection is unable to lower clearing. Rather, it indicates the importance of variation across locations in how much impact protection could possibly have on rates of deforestation. Matching, then, bundles improved estimates of the average impact of protection with guidance on where new parks' impacts will be highest. While many factors will determine where new protected areas will be sited in the future, we claim that the variation across space in protection's impact on deforestation rates should inform site choice.

Præventiv effekt af cykelhjelme

DEFF Research Database (Denmark)

Nielsen, C T; Larsen, C F; Nordentoft, E

1990-01-01

%. Several investigations from abroad and from Denmark have demonstrated that protection of the head can reduce the number of deaths and of acute brain injuries due to bicycle accidents. On the basis of the literature, it is concluded that bicycle helmets provide good protection of the head in connection......The total number of persons injured following bicycle accidents in Denmark is estimated to be more than 50,000 annually. In half of the injured cyclists, lesions localized to the region of the head occur. Bicycle helmets provide considerable protection against brain injuries which constitute 13...... with bicycle accidents. When a bicycle helmet is purchased, it is important to ensure that the helmet fits the head, that vision is not impeded and that the chinstrap secures the helmet correctly. Legislation is necessary to ensure that bicycle helmets sold in Denmark fulfill the minimum safety requirements....

42 CFR 84.1135 - Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods... Air-Purifying High Efficiency Respirators and Combination Gas Masks § 84.1135 Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements. (a) Half-mask facepieces...

Impacts of tourism in the Křivoklátsko Protected Landscape Area

OpenAIRE

Opička, Tomáš

2013-01-01

This thesis deals with tourism and impacts of tourism on the geographic environment. The main purpose is detection of impacts of tourism character, their concentration and intensity in protected area. In this research, author chose the region of the Křivoklatsko protected landscape area. Other aspect this thesis is detection of attandance evolution in confrontation with the proposed Křivoklátsko national park. Key words: tourism, impacts of tourism, the Křivoklátsko protected landscape area, ...

42 CFR 84.175 - Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods....175 Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements. (a) Half-mask facepieces and full facepieces shall be designed and constructed to fit persons with...

Multiscale Analysis of Head Impacts in Contact Sports

Science.gov (United States)

Guttag, Mark; Sett, Subham; Franck, Jennifer; McNamara, Kyle; Bar-Kochba, Eyal; Crisco, Joseph; Blume, Janet; Franck, Christian

2012-02-01

Traumatic brain injury (TBI) is one of the world's major causes of death and disability. To aid companies in designing safer and improved protective gear and to aid the medical community in producing improved quantitative TBI diagnosis and assessment tools, a multiscale finite element model of the human brain, head and neck is being developed. Recorded impact data from football and hockey helmets instrumented with accelerometers are compared to simulated impact data in the laboratory. Using data from these carefully constructed laboratory experiments, we can quantify impact location, magnitude, and linear and angular accelerations of the head. The resultant forces and accelerations are applied to a fully meshed head-form created from MRI data by Simpleware. With appropriate material properties for each region of the head-form, the Abaqus finite element model can determine the stresses, strains, and deformations in the brain. Simultaneously, an in-vitro cellular TBI criterion is being developed to be incorporated into Abaqus models for the brain. The cell-based injury criterion functions the same way that damage criteria for metals and other materials are used to predict failure in structural materials.

Radiation protection and communication. Sociology and communication impact in radiation protection

International Nuclear Information System (INIS)

Berne, G.; Bicheron, G.; Franco, P.

2000-01-01

Communication about nuclear energy was the subject of this conference. Different examples of communications are detailed in fields as different as impact of iodine 131 release in waste waters or public information about radiation protection, the north Cotentin radioecology group or what information to give to the patients in nuclear medicine. (N.C.)

Helmet-mounted displays in long-range-target visual acquisition

Science.gov (United States)

Wilkins, Donald F.

1999-07-01

Aircrews have always sought a tactical advantage within the visual range (WVR) arena -- usually defined as 'see the opponent first.' Even with radar and interrogation foe/friend (IFF) systems, the pilot who visually acquires his opponent first has a significant advantage. The Helmet Mounted Cueing System (HMCS) equipped with a camera offers an opportunity to correct the problems with the previous approaches. By utilizing real-time image enhancement technique and feeding the image to the pilot on the HMD, the target can be visually acquired well beyond the range provided by the unaided eye. This paper will explore the camera and display requirements for such a system and place those requirements within the context of other requirements, such as weight.

Socioeconomic Impacts of Protection Status on Residents of National Parks

Directory of Open Access Journals (Sweden)

Järv Henri

2016-06-01

Full Text Available Rural population ageing and decline is a serious problem throughout Europe resulting in a deterioration of the socioeconomic situation in rural areas. This leads to land abandonment, and consequently the loss of valuable cultural landscapes. Protected areas are no exception and inhabitants also face restrictions arising from the protection status. The aim of this study is to identify the existence, extent and nature of the socioeconomic impacts derived from the protection status on the local population. Population and socioeconomic indicators were compared with the results of in-depth interviews with local stakeholders within 2 Estonian national parks and contextualised with recent social change. It was concluded that protected areas have a considerable socioeconomic impact and in order to preserve cultural landscapes, achieve conservation objectives and contribute to balanced regional development, measures must be taken.

Correlating cumulative sub-concussive head impacts in football with player performance - biomed 2009.

Science.gov (United States)

Rowson, Steven; Goforth, Mike W; Dietter, Dave; Brolinson, P Gunnar; Duma, Stefanan M

2009-01-01

The objective of this study was to investigate the effect of cumulative sub-concussive head impacts on football player performance. The helmets of three Virginia Tech football players were instrumented with a six accelerometer sensor capable of measuring head acceleration. Helmets were instrumented for every game during the 2006 and 2007 football seasons. Each time the head was impacted during a game, the sensor recorded the impact and wirelessly transmitted the data to a sideline computer. Furthermore, the coaching staff at Virginia Tech reviewed post-game film and evaluated each player's performance based on strict criteria. Players were awarded positive points for good plays and negative points for bad plays. Their performance scores were then normalized to a per play basis. Correlations of player performance with cumulative peak linear acceleration and cumulative head injury criterion (HIC) were evaluated. No consistent head acceleration-based measure showed a strong correlation with significance. In addition, relationship trends varied on a position basis. There are many factors other than head impacts that can affect a player's performance and more research is needed to further quantify such effects.

75 FR 22723 - Stream Protection Rule; Environmental Impact Statement

Science.gov (United States)

2010-04-30

..., 784, 816, and 817 RIN 1029-AC63 Stream Protection Rule; Environmental Impact Statement AGENCY: Office... streams from the adverse impacts of surface coal mining operations. We are requesting comments for the... mining activities may be conducted in or near perennial or intermittent streams. That rule, which this...

Helmet-mounted display requirements: just another head-up display (HUD) or a different animal altogether?

Science.gov (United States)

Newman, Richard L.; Haworth, Loran A.

1994-06-01

The helmet-mounted display (HMD) presents flight, navigation, and weapon information in the pilot's line of sight. The HMD was developed to allow the pilot to retain aircraft and weapon information while looking off boresight. The present study reviewed the state-of-the-art in HMDs and identified a number of issues applying to HMDs. Several are identical to head-up display (HUD) issues: symbol standardization, excessive clutter, and the need for integration with other cockpit displays and controls. Other issues are unique to the head-mounted display: symbol stabilization, inadequate definitions, undefined symbol drive laws, helmet considerations, and field-of-view (FOV) vs. resolution tradeoff requirements. Symbol stabilization is critical. In the Apache helicopter, the lack of compensation for pilot head motion creates excessive workload during hovering and nap-of-the-earth (NOE) flight. This high workload translates into excessive training requirements. At the same time, misleading symbology makes interpretation of the height of obstructions impossible. The underlying cause is the absence of design criteria for HMDs. The existing military standard does not reflect the current state of technology. In addition, there are inadequate test and evaluation guidelines. The situation parallels the situation for HUDs several years ago.

Passive Attenuating Communication Earphone (PACE): Noise Attenuation and Speech Intelligibility Performance When Worn in Conjunction with the HGU-56/P and HGU-55/P Flight Helmets

Science.gov (United States)

2013-10-16

right) eartips The purpose of this study was to integrate the HGU-56/P and HGU-55/P flight helmets with PACE to measure the noise attenuation and...55/P flight helmet integrated with PACE 2.0 METHODS 2.1 Subjects Twenty paid volunteer subjects (9 male, 11 female) participated in the study ...Pan Pad Pat Path Pack Pass Buff Bus But Bug Buck Bun Sat Sag Sass Sack Sad Sap Run Sun Bun Gun Fun Nun 8 Distribution A: Approved for

Evolving protected-area impacts in Panama: impact shifts show that plans require anticipation

International Nuclear Information System (INIS)

Haruna, Akiko; Pfaff, Alexander; Van den Ende, Sander; Joppa, Lucas

2014-01-01

Protected areas (PAs) are the leading forest conservation policy, so accurate evaluation of future PA impact is critical in conservation planning. Yet by necessity impact evaluations use past data. Here we argue that forward-looking plans should blend such evaluations with anticipation of shifts in threats. Applying improved methods to evaluate past impact, we provide rigorous support for that conceptual approach by showing that PAs’ impacts on deforestation shifted with land use. We study the Republic of Panama, where species-dense tropical forest faces real pressure. Facing variation in deforestation pressure, the PAs’ impacts varied across space and time. Thus, if shifts in pressure levels and patterns could be anticipated, that could raise impact. (paper)

Laboratory Evaluation of Low-Cost Wearable Sensors for Measuring Head Impacts in Sports.

Science.gov (United States)

Tyson, Abigail M; Duma, Stefan M; Rowson, Steven

2018-04-03

Advances in low-cost wearable head impact sensor technology provide potential benefits regarding sports safety for both consumers and researchers. However, previous laboratory evaluations are not directly comparable and don't incorporate test conditions representative of unhelmeted impacts. This study addresses those limitations. The xPatch by X2 Biosystems and the SIM-G by Triax Technologies were placed on a NOCSAE headform with a Hybrid III neck which underwent impacts tests using a pendulum. Impact conditions included helmeted, padded impactor to bare head, and rigid impactor to bare head to represent long and short-duration impacts seen in helmeted and unhelmeted sports. The wearable sensors were evaluated on their kinematic accuracy by comparing results to reference sensors located at the headform center of gravity. Statistical tests for equivalence were performed on the slope of the linear regression between wearable sensors and reference. The xPatch gave equivalent measurements to the reference in select longer-duration impacts whereas the SIM-G had large variance leading to no equivalence. For the short-duration impacts, both wearable sensors underpredicted the reference. This error can be improved with increases in sampling rate from 1 to 1.5 kHz. Follow-up evaluations should be performed on the field to identify error in vivo. (197/200).

Study of efficiency and current use of respiratory protective devices

International Nuclear Information System (INIS)

Linauskas, S.H.; Kalos, F.

1984-12-01

The efficiency of a helmet-type powered air-purifying respirator was studied in the work environment of an underground uranium mine. Workplace protection factors (WPF) were measured, using approximately 30-minute air sampling periods and repeated sampling throughout the work shifts for six miners during three shifts each. The WPF of the modified Racal AH-5 helmet was 17.8 (geometric mean) with new filters in the respirator; the WPF dropped to 5.3 when four-day-old filters were used. The WPF results were lognormally distributed. The test population appeared to be a homogeneous set: there was no significant difference in the mean WPFs of individual test subjects. The study could not resolve any effect of elapsed time within the work shift or of ambient Working Level on the WPF. The actual use levels and the problems associated with respirator use were studied at the same time, principally via a user survey. The respirators have a high level of acceptance among the user population of underground uranium miners and 72.5 percent of the 207 survey respondents stated six or more hours use with the visor in the correct 'down' position per shift

Protected Areas' Impacts on Brazilian Amazon Deforestation: Examining Conservation-Development Interactions to Inform Planning.

Directory of Open Access Journals (Sweden)

Alexander Pfaff

Full Text Available Protected areas are the leading forest conservation policy for species and ecoservices goals and they may feature in climate policy if countries with tropical forest rely on familiar tools. For Brazil's Legal Amazon, we estimate the average impact of protection upon deforestation and show how protected areas' forest impacts vary significantly with development pressure. We use matching, i.e., comparisons that are apples-to-apples in observed land characteristics, to address the fact that protected areas (PAs tend to be located on lands facing less pressure. Correcting for that location bias lowers our estimates of PAs' forest impacts by roughly half. Further, it reveals significant variation in PA impacts along development-related dimensions: for example, the PAs that are closer to roads and the PAs closer to cities have higher impact. Planners have multiple conservation and development goals, and are constrained by cost, yet still conservation planning should reflect what our results imply about future impacts of PAs.

Protected Areas' Impacts on Brazilian Amazon Deforestation: Examining Conservation-Development Interactions to Inform Planning.

Science.gov (United States)

Pfaff, Alexander; Robalino, Juan; Herrera, Diego; Sandoval, Catalina

2015-01-01

Protected areas are the leading forest conservation policy for species and ecoservices goals and they may feature in climate policy if countries with tropical forest rely on familiar tools. For Brazil's Legal Amazon, we estimate the average impact of protection upon deforestation and show how protected areas' forest impacts vary significantly with development pressure. We use matching, i.e., comparisons that are apples-to-apples in observed land characteristics, to address the fact that protected areas (PAs) tend to be located on lands facing less pressure. Correcting for that location bias lowers our estimates of PAs' forest impacts by roughly half. Further, it reveals significant variation in PA impacts along development-related dimensions: for example, the PAs that are closer to roads and the PAs closer to cities have higher impact. Planners have multiple conservation and development goals, and are constrained by cost, yet still conservation planning should reflect what our results imply about future impacts of PAs.

Greater Focus Needed on Alien Plant Impacts in Protected Areas

Czech Academy of Sciences Publication Activity Database

Hulme, P. E.; Pyšek, Petr; Pergl, Jan; Jarošík, Vojtěch; Schaffner, U.; Vila, M.

2014-01-01

Roč. 7, č. 5 (2014), s. 459-466 ISSN 1755-263X R&D Projects: GA ČR(CZ) GAP504/11/1028 Institutional support: RVO:67985939 Keywords : plant invasions * impact * protected areas Subject RIV: EF - Botanics Impact factor: 7.241, year: 2014

Impact Testing of Orbiter Thermal Protection System Materials

Science.gov (United States)

Kerr, Justin

2006-01-01

This viewgraph presentation reviews the impact testing of the materials used in designing the shuttle orbiter thermal protection system (TPS). Pursuant to the Columbia Accident Investigation Board recommendations a testing program of the TPS system was instituted. This involved using various types of impactors in different sizes shot from various sizes and strengths guns to impact the TPS tiles and the Leading Edge Structural Subsystem (LESS). The observed damage is shown, and the resultant lessons learned are reviewed.

Cost Analysis of Noninvasive Helmet Ventilation Compared with Use of Noninvasive Face Mask in ARDS

Directory of Open Access Journals (Sweden)

Kwadwo Kyeremanteng

2018-01-01

Full Text Available Intensive care unit (ICU costs have doubled since 2000, totalling 108 billion dollars per year. Acute respiratory distress syndrome (ARDS has a prevalence of 10.4% and a 28-day mortality of 34.8%. Noninvasive ventilation (NIV is used in up to 30% of cases. A recent randomized controlled trial by Patel et al. (2016 showed lower intubation rates and 90-day mortality when comparing helmet to face mask NIV in ARDS. The population in the Patel et al. trial was used for cost analysis in this study. Projections of cost savings showed a decrease in ICU costs by $2527 and hospital costs by $3103 per patient, along with a 43.3% absolute reduction in intubation rates. Sensitivity analysis showed consistent cost reductions. Projected annual cost savings, assuming the current prevalence of ARDS, were $237538 in ICU costs and $291682 in hospital costs. At a national level, using yearly incidence of ARDS cases in American ICUs, this represents $449 million in savings. Helmet NIV, compared to face mask NIV, in nonintubated patients with ARDS, reduces ICU and hospital direct-variable costs along with intubation rates, LOS, and mortality. A large-scale cost-effectiveness analysis is needed to validate the findings.

Identifying and assessing ecotourism visitor impacts at selected protected areas in Costa Rica and Belize

Science.gov (United States)

Farrell, T.A.; Marion, J.L.

2001-01-01

Protected area visitation is an important component of ecotourism, and as such, must be sustainable. However, protected area visitation may degrade natural resources, particularly in areas of concentrated visitor activities like trails and recreation sites. This is an important concern in ecotourism destinations such as Belize and Costa Rica, because they actively promote ecotourism and emphasize the pristine qualities of their natural resources. Research on visitor impacts to protected areas has many potential applications in protected area management, though it has not been widely applied in Central and South America. This study targeted this deficiency through manager interviews and evaluations of alternative impact assessment procedures at eight protected areas in Belize and Costa Rica. Impact assessment procedures included qualitative condition class systems, ratings systems, and measurement-based systems applied to trails and recreation sites. The resulting data characterize manager perceptions of impact problems, document trail and recreation site impacts, and provide examples of inexpensive, efficient and effective rapid impact assessment procedures. Interview subjects reported a variety of impacts affecting trails, recreation sites, wildlife, water, attraction features and other resources. Standardized assessment procedures were developed and applied to record trail and recreation site impacts. Impacts affecting the study areas included trail proliferation, erosion and widening, muddiness on trails, vegetation cover loss, soil and root exposure, and tree damage on recreation sites. The findings also illustrate the types of assessment data yielded by several alternative methods and demonstrate their utility to protected area managers. The need for additional rapid assessment procedures for wildlife, water, attraction feature and other resource impacts was also identified.

Maxillofacial and dental injuries sustained in hurling.

LENUS (Irish Health Repository)

Murphy, C

2010-06-01

The incidence of facial injuries in hurling has decreased since the introduction of helmets with facial protection. The aim of this study was to identify the incidence of facial and dental injuries sustained in hurling training or matches and compliance with wearing helmets, with or without modified or unmodified faceguards. This prospective study included all patients who attended the Mid Western Regional Hospital Limerick, with injuries sustained while playing hurling during 2007 and 2008 seasons. The study population included 70 patients. Forty two (60%) injuries occurred during practice and 28(40%) during matches. Fifty two players (75%) sustained facial injuries whilst no helmet was worn. Eighteen injuries (25%) were sustained by players wearing helmets. Th study demonstrates that 60% of injuries occur during training when players do not wear helmets. We support the recent introduction by the GAA making it compulsory to wear helmets with faceguard protection from January 1st 2010.

Crumple zone design for pedestrian protection using impact analysis

Energy Technology Data Exchange (ETDEWEB)

Moon, Hyung Il; Jeon, Young Eun; Kim, Dae Young; Kim, Heon Young [Kangwon National Univ., Chuncheon si (Korea, Republic of); Kim, Yong Soo [Product Development Team, Gyeongsan si (Korea, Republic of)

2012-08-15

This paper describes the design process for an automobile crumple zone for pedestrian protection. The impact load and bending moments predicted by impact analysis were used to design a plastic structure that may help reduce pedestrian injuries to the thigh area. The fracture effect was incorporated into the model by calculating the damage to the plastic material during impact, and the analysis was conducted under the European New Car Assessment Program (Euro NCAP) test conditions, using the upper legform developed by ESI Corporation. In addition, the values predicted by the analysis were validated by comparison with results of actual impact tests.

Crumple zone design for pedestrian protection using impact analysis

International Nuclear Information System (INIS)

Moon, Hyung Il; Jeon, Young Eun; Kim, Dae Young; Kim, Heon Young; Kim, Yong Soo

2012-01-01

This paper describes the design process for an automobile crumple zone for pedestrian protection. The impact load and bending moments predicted by impact analysis were used to design a plastic structure that may help reduce pedestrian injuries to the thigh area. The fracture effect was incorporated into the model by calculating the damage to the plastic material during impact, and the analysis was conducted under the European New Car Assessment Program (Euro NCAP) test conditions, using the upper legform developed by ESI Corporation. In addition, the values predicted by the analysis were validated by comparison with results of actual impact tests

Protected Area Reconfiguration Project. Environmental Assessment and Finding of No Significant Impact

International Nuclear Information System (INIS)

1995-12-01

DOE has decided to consolidate, process, and store Category I and II Special Nuclear Material (SNM) in Building 371 at Rocky Flats, in order to improve safeguards and security and to reduce baseline facility and personnel costs. Once all SNM in consolidated into this building, maintaining the full 200-acre protected area would no longer be necessary, and the protected area (PA) could be reconfigured to include only the protection requirements necessary for Building 371. DOE Environmental Assessment 1132 has been written to evaluate options for reconfiguration of the PA; it addressed potential environmental impacts resulting from construction of fence alternatives. Possible routes for the new fence section were examined for environmental impact, feasibility, cost, and complexity. A number of the alternatives, including the proposed action, would impact wetlands

Persuasion to use personal protective equipment in constructing subway stations: application of social marketing.

Science.gov (United States)

Shamsi, Mahmoud; Pariani, Abbas; Shams, Mohsen; Soleymani-nejad, Marzieh

2016-04-01

To study the effects of an intervention based on social marketing to persuade workers to use personal protective equipment (PPE) in constructing subway stations in Isfahan, Iran. This was a quasi-experimental study. Two stations were selected as intervention and control groups. Intervention was designed based on results of a formative research. A free package containing a safety helmet with a tailored message affixed to it, mask and gloves and an educational pamphlet was delivered to the intervention group. After 6 weeks, behaviours in the intervention and control stations were measured using an observational checklist. After the intervention, the percentage of workers who used PPE at the intervention station increased significantly. OR for helmet and mask usage was 7.009 and 2.235, respectively, in the intervention group. Social marketing can be used to persuade workers to use PPE in the workplace. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Persistent, Long-term Cerebral White Matter Changes after Sports-Related Repetitive Head Impacts

Science.gov (United States)

Bazarian, Jeffrey J.; Zhu, Tong; Zhong, Jianhui; Janigro, Damir; Rozen, Eric; Roberts, Andrew; Javien, Hannah; Merchant-Borna, Kian; Abar, Beau; Blackman, Eric G.

2014-01-01

Introduction Repetitive head impacts (RHI) sustained in contact sports are thought to be necessary for the long-term development of chronic traumatic encephalopathy (CTE). Our objectives were to: 1) characterize the magnitude and persistence of RHI-induced white matter (WM) changes; 2) determine their relationship to kinematic measures of RHI; and 3) explore their clinical relevance. Methods Prospective, observational study of 10 Division III college football players and 5 non-athlete controls during the 2011-12 season. All subjects underwent diffusion tensor imaging (DTI), physiologic, cognitive, and balance testing at pre-season (Time 1), post-season (Time 2), and after 6-months of no-contact rest (Time 3). Head impact measures were recorded using helmet-mounted accelerometers. The percentage of whole-brain WM voxels with significant changes in fractional anisotropy (FA) and mean diffusivity (MD) from Time 1 to 2, and Time 1 to 3 was determined for each subject and correlated to head impacts and clinical measures. Results Total head impacts for the season ranged from 431–1,850. No athlete suffered a clinically evident concussion. Compared to controls, athletes experienced greater changes in FA and MD from Time 1 to 2 as well as Time 1 to 3; most differences at Time 2 persisted to Time 3. Among athletes, the percentage of voxels with decreased FA from Time 1 to 2 was positively correlated with several helmet impact measures. The persistence of WM changes from Time 1 to 3 was also associated with changes in serum ApoA1 and S100B autoantibodies. WM changes were not consistently associated with cognition or balance. Conclusions A single football season of RHIs without clinically-evident concussion resulted in WM changes that correlated with multiple helmet impact measures and persisted following 6 months of no-contact rest. This lack of WM recovery could potentially contribute to cumulative WM changes with subsequent RHI exposures. PMID:24740265

Minimising visitor impacts to protected areas: The efficacy of low impact education programmes

Science.gov (United States)

Marion, J.L.; Reid, S.E.

2007-01-01

Protected area managers, tourism providers, and other organisations commonly employ education programmes to address visitation-related impairment of natural and cultural resources, social conditions, and neighbouring communities. These programmes have different names (Leave No Trace, Codes of Conduct, Environmental Guidelines for Tourists) but share common objectives: to sustain opportunities for high quality visitor experiences while avoiding or minimising associated negative impacts to protected area resources, visitor experiences, and park neighbours. Theoretical and empirical research studies in the United States are reviewed to evaluate the efficacy of educational efforts that seek to encourage adoption of low impact behaviours. Findings reveal that most of the visitor education efforts evaluated did effectively alter visitor knowledge, behaviour and/or resource and social conditions in the intended direction. These findings, including discussions of message content, delivery, audience characteristics and theoretical grounding, provide insights for improving the efficacy of future educational efforts.

Protection of mechanized timberings on beds dangerous for mine impacts

Energy Technology Data Exchange (ETDEWEB)

Budirsky, S

1982-01-01

In some stoping faces on beds which are dangerous for mine impacts, mechanized timbering is successfully used which is not equipped with protection from the effect of these dynamic phenomena. This generated the idea that in the indicated conditions, mechanized timbering may not be equipped with protective devices against dynamic loads. Theoretical studies have shown that the effects of mine impacts depends on the total energy of the impact, distance of this stoping face from the epicenter of the impact, as well as the capacity of the rock massif to transmit and absorb energy of the mine impact. This means that the effect of the mine impact under different conditions is not the same, the mine impacts of lower energy under definite conditions can result in greater damages to the mechanized timbering than mine impact with higher energy. It is believed that the effect of absorption of energy of the mine impact depends on the method of control of the roofing in the stoping face, the presence of hydraulic fill quarantees absorption of up to 80% of its energy. The experience of working beds which are dangerous for mine impacts in the upper Silesia coal basin indicated that the designs of the mechanized timbering, especially shield, in which the stands are not rigidly connected to the roof timber, during operation on beds with thickness 2.5-4 m withstand mine impacts with energy 10/sup 7/ J without significant disorders (mine impacts with this energy occur very frequently . For energy of mine impact of 108 J (impacts with this energy are observed comparatively rarely), the mechanized timberings are considerably damaged.

A data protection impact assessment methodology for cloud

NARCIS (Netherlands)

Stefanatou, Dimitra; Dalla Corte, Lorenzo; Leenes, Ronald

2016-01-01

We propose a data protection impact assessment (DPIA) method based on suc-cessive questionnaires for an initial screening and for a full screening for a given project. These were tailored to satisfy the needs of Small and Medium Enterprises (SMEs) that intend to process personal data in the cloud.

Protected Areas’ Impacts on Brazilian Amazon Deforestation: Examining Conservation – Development Interactions to Inform Planning

Science.gov (United States)

Pfaff, Alexander; Robalino, Juan; Herrera, Diego; Sandoval, Catalina

2015-01-01

Protected areas are the leading forest conservation policy for species and ecoservices goals and they may feature in climate policy if countries with tropical forest rely on familiar tools. For Brazil's Legal Amazon, we estimate the average impact of protection upon deforestation and show how protected areas’ forest impacts vary significantly with development pressure. We use matching, i.e., comparisons that are apples-to-apples in observed land characteristics, to address the fact that protected areas (PAs) tend to be located on lands facing less pressure. Correcting for that location bias lowers our estimates of PAs’ forest impacts by roughly half. Further, it reveals significant variation in PA impacts along development-related dimensions: for example, the PAs that are closer to roads and the PAs closer to cities have higher impact. Planners have multiple conservation and development goals, and are constrained by cost, yet still conservation planning should reflect what our results imply about future impacts of PAs. PMID:26225922

The impacts of distributed generators on protections and some solutions

Energy Technology Data Exchange (ETDEWEB)

Ciufo, J.; Cooperberg, A. [Hydro One Networks Inc., Toronto, ON (Canada)

2010-07-01

A significant proportion of the new generation capacity planned for Ontario's Hydro One utility will include distributed generation (DG). The Ontario Power Authority (OPA) has approved the connection of 252 DG facilities. It is expected that the high penetration of DG systems will have an impact on load-connected stations and distribution feeders in the region. This power point presentation discussed potential challenges and solutions for connecting the DG systems to the Hydro One network. An overview of the existing DG system was presented. Potential impacts to the network included an increase in fault current magnitudes, variations in fault currents, and islanding. The installation of DGs may also introduce issues related to automatic reclosing. The use of DG systems may also result in over-voltage and lead to the desensitization of protection equipment. Solutions to the potential problems included the development of a feeder protection system with phase and ground distance elements for instantaneous protection and line protection devices with all relay elements. The multiple setting groups used in the system will be used to facilitate smart grid options in the future. tabs., figs.

Forensic reconstruction of two military combat related shooting incidents using an anatomically correct synthetic skull with a surrogate skin/soft tissue layer.

Science.gov (United States)

Mahoney, Peter; Carr, Debra; Harrison, Karl; McGuire, Ruth; Hepper, Alan; Flynn, Daniel; Delaney, Russ J; Gibb, Iain

2018-03-07

Six synthetic head models wearing ballistic protective helmets were used to recreate two military combat-related shooting incidents (three per incident, designated 'Incident 1' and 'Incident 2'). Data on the events including engagement distances, weapon and ammunition types was collated by the Defence Science and Technology Laboratory. The models were shot with 7.62 × 39 mm ammunition downloaded to mean impact velocities of 581 m/s (SD 3.5 m/s) and 418 m/s (SD 8 m/s), respectively, to simulate the engagement distances. The damage to the models was assessed using CT imaging and dissection by a forensic pathologist experienced in reviewing military gunshot wounds. The helmets were examined by an MoD engineer experienced in ballistic incident analysis. Damage to the helmets was consistent with that seen in real incidents. Fracture patterns and CT imaging on two of the models for Incident 1 (a frontal impact) were congruent with the actual incident being modelled. The results for Incident 2 (a temporoparietal impact) produced realistic simulations of tangential gunshot injury but were less representative of the scenario being modelled. Other aspects of the wounds produced also exhibited differences. Further work is ongoing to develop the models for greater ballistic injury fidelity.

Environmental and Physiological Factors Affect Football Head Impact Biomechanics.

Science.gov (United States)

Mihalik, Jason P; Sumrall, Adam Z; Yeargin, Susan W; Guskiewicz, Kevin M; King, Kevin B; Trulock, Scott C; Shields, Edgar W

2017-10-01

Recent anecdotal trends suggest a disproportionate number of head injuries in collegiate football players occur during preseason football camp. In warmer climates, this season also represents the highest risk for heat-related illness among collegiate football players. Because concussion and heat illnesses share many common symptoms, we need 1) to understand if environmental conditions, body temperature, and hydration status affect head impact biomechanics; and 2) to determine if an in-helmet thermistor could provide a valid measure of gastrointestinal temperature. A prospective cohort of 18 Division I college football players (age, 21.1 ± 1.4 yr; height, 187.7 ± 6.6 cm; mass, 114.5 ± 23.4 kg). Data were collected during one control and three experimental sessions. During each session, the Head Impact Telemetry System recorded head impact biomechanics (linear acceleration, rotational acceleration, and severity profile) and in-helmet temperature. A wet bulb globe device recorded environmental conditions, and CorTemp™ Ingestible Core Body Temperature Sensors recorded gastrointestinal temperature. Our findings suggest that linear acceleration (P = 0.57), rotational acceleration (P = 0.16), and Head Impact Technology severity profile (P = 0.33) are not influenced by environmental or physiological conditions. We did not find any single or combination of predictors for impact severity. Rotational acceleration was approaching significance between our early experimental sessions when compared with our control session. More research should be conducted to better understand if rotational accelerations are a component of impact magnitudes that are affected due to changes in environmental conditions, body temperature, and hydration status.

A universal and smart helmet-mounted display of large FOV

Science.gov (United States)

Zhang, Nan; Weng, Dongdong; Wang, Yongtian; Li, Xuan; Liu, Youhai

2011-11-01

HMD (head-mounted display) is an important virtual reality device, which has played a vital role in VR application system. Compared with traditional HMD which cannot be applied in the daily life owing to their disadvantage on the price and performance, a new universal and smart Helmet-Mounted Display of large FOV uses excellent performance and widespread popularity as its starting point. By adopting simplified visual system and transflective system that combines the transmission-type and reflection-type display system with transflective glass based on the Huggens-Fresnel principle, we have designed a HMD with wide field of view, which can be easy to promote and popularize. Its resolution is 800*600, and field of view is 36.87°(vertical)* 47.92°(horizontal). Its weight is only 1080g. It has caught up with the advanced world levels.

Measuring impact of protected area management interventions: current and future use of the Global Database of Protected Area Management Effectiveness.

Science.gov (United States)

Coad, Lauren; Leverington, Fiona; Knights, Kathryn; Geldmann, Jonas; Eassom, April; Kapos, Valerie; Kingston, Naomi; de Lima, Marcelo; Zamora, Camilo; Cuardros, Ivon; Nolte, Christoph; Burgess, Neil D; Hockings, Marc

2015-11-05

Protected areas (PAs) are at the forefront of conservation efforts, and yet despite considerable progress towards the global target of having 17% of the world's land area within protected areas by 2020, biodiversity continues to decline. The discrepancy between increasing PA coverage and negative biodiversity trends has resulted in renewed efforts to enhance PA effectiveness. The global conservation community has conducted thousands of assessments of protected area management effectiveness (PAME), and interest in the use of these data to help measure the conservation impact of PA management interventions is high. Here, we summarize the status of PAME assessment, review the published evidence for a link between PAME assessment results and the conservation impacts of PAs, and discuss the limitations and future use of PAME data in measuring the impact of PA management interventions on conservation outcomes. We conclude that PAME data, while designed as a tool for local adaptive management, may also help to provide insights into the impact of PA management interventions from the local-to-global scale. However, the subjective and ordinal characteristics of the data present significant limitations for their application in rigorous scientific impact evaluations, a problem that should be recognized and mitigated where possible. © 2015 The Authors.

Measuring the impact of child protection through Activation States

OpenAIRE

Pawlaczek, Z; Bringer, JD; Cockburn, C; Nutt, G; Pitchford, A; Russell, K; Brackenridge, CH

2005-01-01

Child protection (CP) has risen to the top of the UK sports policy agenda in the past four years and the Football Association has invested in this major strategy as part of its commitment to “use the power of football to build a better future” (FA, 2000a). Evidencing the impact of child protection is, however, a complex task, exacerbated by the dearth of measurement tools that exist for this purpose in sport. This article presents a new model of ‘Activation States’ that has been designed and...

Produto Sustentável: Equipamento de Proteção Individual Fabricado com Plástico Verde

OpenAIRE

Boa Vista, Hamilton Aparecido; Universidade Nove de Julho - UNINOVE/GeAS, São Paulo; dos Santos, Mário Roberto; Universidade Nove de Julho - Uninove?PPGA, São Paulo; Shibao, Fábio Ytoshi; Universidade Nove de Julho - UNINOVE/GeAS, São Paulo

2015-01-01

This study analyzed the case of manufacturing of Personal Protective Equipment (PPE) using as raw material biopolymers produced from ethanol from sugar cane, known as green polypropylene, produced since 2008 by BRASKEM. This article studied the PPE for the employee’s head protection, named helmet by NR 6, which is used in situations of exposure to weather and work scenarios in places where there is risk of impact from falling or projecting objects, burns, electric shock, and solar radiation. ...

Radiation protection and communication. Sociology and communication impact in radiation protection; Radioprotection et Communication. Sociologie et impact de la communication en radioprotection

Energy Technology Data Exchange (ETDEWEB)

Berne, G [CEA/Cadarache, Service de Protection contre les Rayonnements, 13 - Saint Paul lez Durance (France); Bicheron, G; Franco, P [CEA/Fontenay aux Roses, Inst. de Protection et de Surete Nucleaire, IPSN, 92 (France); and others

2000-07-01

Communication about nuclear energy was the subject of this conference. Different examples of communications are detailed in fields as different as impact of iodine 131 release in waste waters or public information about radiation protection, the north Cotentin radioecology group or what information to give to the patients in nuclear medicine. (N.C.)

Injury protection and accident causation parameters for vulnerable road users based on German In-Depth Accident Study GIDAS.

Science.gov (United States)

Otte, Dietmar; Jänsch, Michael; Haasper, Carl

2012-01-01

Within a study of accident data from GIDAS (German In-Depth Accident Study), vulnerable road users are investigated regarding injury risk in traffic accidents. GIDAS is the largest in-depth accident study in Germany. Due to a well-defined sampling plan, representativeness with respect to the federal statistics is also guaranteed. A hierarchical system ACASS (Accident Causation Analysis with Seven Steps) was developed in GIDAS, describing the human causation factors in a chronological sequence. The accordingly classified causation factors - derived from the systematic of the analysis of human accident causes ("7 steps") - can be used to describe the influence of accident causes on the injury outcome. The bases of the study are accident documentations over ten years from 1999 to 2008 with 8204 vulnerable road users (VRU), of which 3 different groups were selected as pedestrians n=2041, motorcyclists n=2199 and bicyclists n=3964, and analyzed on collisions with cars and trucks as well as vulnerable road users alone. The paper will give a description of the injury pattern and injury mechanisms of accidents. The injury frequencies and severities are pointed out considering different types of VRU and protective measures of helmet and clothes of the human body. The impact points are demonstrated on the car, following to conclusion of protective measures on the vehicle. Existing standards of protection devices as well as interdisciplinary research, including accident and injury statistics, are described. With this paper, a summarization of the existing possibilities on protective measures for pedestrians, bicyclists and motorcyclists is given and discussed by comparison of all three groups of vulnerable road users. Also the relevance of special impact situations and accident causes mainly responsible for severe injuries are pointed out, given the new orientation of research for the avoidance and reduction of accident patterns. 2010 Elsevier Ltd. All rights reserved.

Impact of the probability of causation on the radiation protection program

International Nuclear Information System (INIS)

Meinhold, C.B.

1988-01-01

Although the probability of causation approach is the only scientific basis on which a given cancer can be judged to be causally related to a given exposure, the impact of this concept on the radiation safety program could be counter-productive. As health physicists, the practices and the concepts we employ have been developed to protect the worker. Effective dose equivalent and committed dose equivalent are protective concepts but useless for probability of causation analysis. Perhaps extensive records will be the only way that good radiation protection and probability of causation analysis can coexist

Assessing impacts of intensified biomass production and biodiversity protection on ecosystem services provided by European forests

NARCIS (Netherlands)

Verkerk, P.J.; Mavsar, R.; Giergiczny, M.; Lindner, M.; Edwards, D.; Schelhaas, M.J.

2014-01-01

To develop viable strategies for intensifying the use of forest biomass and for increasing forest protection, impacts on ecosystem services need to be assessed. We investigated the biophysical and economic impacts of increased forest biomass production and biodiversity protection on forest ecosystem

Making parks make a difference: poor alignment of policy, planning and management with protected-area impact, and ways forward.

Science.gov (United States)

Pressey, Robert L; Visconti, Piero; Ferraro, Paul J

2015-11-05

Policy and practice around protected areas are poorly aligned with the basic purpose of protection, which is to make a difference. The difference made by protected areas is their impact, defined in program evaluation as the outcomes arising from protection relative to the counterfactual of no protection or a different form of protection. Although impact evaluation of programs is well established in fields such as medicine, education and development aid, it is rare in nature conservation. We show that the present weak alignment with impact of policy targets and operational objectives for protected areas involves a great risk: targets and objectives can be achieved while making little difference to the conservation of biodiversity. We also review potential ways of increasing the difference made by protected areas, finding a poor evidence base for the use of planning and management 'levers' to better achieve impact. We propose a dual strategy for making protected areas more effective in their basic role of saving nature, outlining ways of developing targets and objectives focused on impact while also improving the evidence for effective planning and management. © 2015 The Authors.

Impact of VSC Control Strategies and Incorporation of Synchronous Condensers on Distance Protection under Unbalanced Faults

DEFF Research Database (Denmark)

Jia, Jundi; Yang, Guangya; Nielsen, Arne Hejde

2018-01-01

on distance protection are evaluated using a commercial relay through hardware-in-the-loop (HIL) tests. Based on the test results, we propose to avoid using constant reactive power control strategy. It poses an adverse impact on the reliability and speed of distance protection regardless of the presence of SC....... This might bring up challenges to the protection system of a converter-dominated power system. This paper derives a generic converter peak current limitation method for three different VSC control strategies. The impact of the control strategies and the combined impact of a VSC with a synchronous condenser...... at the point of common coupling (PCC), while constant active power and balanced current control strategies favor the performances of distance protection....

Wearable nanosensor system for monitoring mild traumatic brain injuries in football players

Science.gov (United States)

Ramasamy, Mouli; Varadan, Vijay K.

2016-04-01

Football players are more to violent impacts and injuries more than any athlete in any other sport. Concussion or mild traumatic brain injuries were one of the lesser known sports injuries until the last decade. With the advent of modern technologies in medical and engineering disciplines, people are now more aware of concussion detection and prevention. These concussions are often overlooked by football players themselves. The cumulative effect of these mild traumatic brain injuries can cause long-term residual brain dysfunctions. The principle of concussion is based the movement of the brain in the neurocranium and viscerocranium. The brain is encapsulated by the cerebrospinal fluid which acts as a protective layer for the brain. This fluid can protect the brain against minor movements, however, any rapid movements of the brain may mitigate the protective capability of the cerebrospinal fluid. In this paper, we propose a wireless health monitoring helmet that addresses the concerns of the current monitoring methods - it is non-invasive for a football player as helmet is not an additional gear, it is efficient in performance as it is equipped with EEG nanosensors and 3D accelerometer, it does not restrict the movement of the user as it wirelessly communicates to the remote monitoring station, requirement of individual monitoring stations are not required for each player as the ZigBee protocol can couple multiple transmitters with one receiver. A helmet was developed and validated according to the above mentioned parameters.

Wireless nanosensors for monitoring concussion of football players

Science.gov (United States)

Ramasamy, Mouli; Harbaugh, Robert E.; Varadan, Vijay K.

2015-04-01

Football players are more to violent impacts and injuries more than any athlete in any other sport. Concussion or mild traumatic brain injuries were one of the lesser known sports injuries until the last decade. With the advent of modern technologies in medical and engineering disciplines, people are now more aware of concussion detection and prevention. These concussions are often overlooked by football players themselves. The cumulative effect of these mild traumatic brain injuries can cause long-term residual brain dysfunctions. The principle of concussion is based the movement of the brain in the neurocranium and viscerocranium. The brain is encapsulated by the cerebrospinal fluid which acts as a protective layer for the brain. This fluid can protect the brain against minor movements, however, any rapid movements of the brain may mitigate the protective capability of the cerebrospinal fluid. In this paper, we propose a wireless health monitoring helmet that addresses the concerns of the current monitoring methods - it is non-invasive for a football player as helmet is not an additional gear, it is efficient in performance as it is equipped with EEG nanosensors and 3D accelerometer, it does not restrict the movement of the user as it wirelessly communicates to the remote monitoring station, requirement of individual monitoring stations are not required for each player as the ZigBee protocol can couple multiple transmitters with one receiver. A helmet was developed and validated according to the above mentioned parameters.

Impacts of cathodic protection on waste package performance

International Nuclear Information System (INIS)

Atkins, J.E.; Lee, J.H.; Andrews, R.W.

1996-01-01

The current design concept for a multi-barrier waste container for the potential repository at Yucca Mountain, Nevada, calls for an outer barrier of 100 mm thick corrosion-allowance material (CAM) (carbon steel) and an inner barrier of 20 mm thick corrosion-resistant material (CRM) (Alloy 825). Fulfillment of the NRC subsystem requirements (10 CFR 60.113) of substantially complete containment and controlled release of radionuclides from the engineered barrier system (EBS) will rely mostly upon the robust waste container design, among other EBS components. In the current waste container design, some degree of cathodic protection of CRM will be provided by CAM. This paper discusses a sensitivity case study for the impacts of cathodic protection of the inner barrier by the outer barrier on the performance of waste package

Computational Model for Impact-Resisting Critical Thickness of High-Speed Machine Outer Protective Plate

Science.gov (United States)

Wu, Huaying; Wang, Li Zhong; Wang, Yantao; Yuan, Xiaolei

2018-05-01

The blade or surface grinding blade of the hypervelocity grinding wheel may be damaged due to too high rotation rate of the spindle of the machine and then fly out. Its speed as a projectile may severely endanger the field persons. Critical thickness model of the protective plate of the high-speed machine is studied in this paper. For easy analysis, the shapes of the possible impact objects flying from the high-speed machine are simplified as sharp-nose model, ball-nose model and flat-nose model. Whose front ending shape to represent point, line and surface contacting. Impact analysis based on J-C model is performed for the low-carbon steel plate with different thicknesses in this paper. One critical thickness computational model for the protective plate of high-speed machine is established according to the damage characteristics of the thin plate to get relation among plate thickness and mass, shape and size and impact speed of impact object. The air cannon is used for impact test. The model accuracy is validated. This model can guide identification of the thickness of single-layer outer protective plate of a high-speed machine.

Protected area types, strategies and impacts in Brazil's Amazon: public protected area strategies do not yield a consistent ranking of protected area types by impact

Science.gov (United States)

Pfaff, Alexander; Robalino, Juan; Sandoval, Catalina; Herrera, Diego

2015-01-01

The leading policy to conserve forest is protected areas (PAs). Yet, PAs are not a single tool: land users and uses vary by PA type; and public PA strategies vary in the extent of each type and in the determinants of impact for each type, i.e. siting and internal deforestation. Further, across regions and time, strategies respond to pressures (deforestation and political). We estimate deforestation impacts of PA types for a critical frontier, the Brazilian Amazon. We separate regions and time periods that differ in their deforestation and political pressures and document considerable variation in PA strategies across regions, time periods and types. The siting of PAs varies across regions. For example, all else being equal, PAs in the arc of deforestation are relatively far from non-forest, while in other states they are relatively near. Internal deforestation varies across time periods, e.g. it is more similar across the PA types for PAs after 2000. By contrast, after 2000, PA extent is less similar across PA types with little non-indigenous area created inside the arc. PA strategies generate a range of impacts for PA types—always far higher within the arc—but not a consistent ranking of PA types by impact. PMID:26460126

Protected area types, strategies and impacts in Brazil's Amazon: public protected area strategies do not yield a consistent ranking of protected area types by impact.

Science.gov (United States)

Pfaff, Alexander; Robalino, Juan; Sandoval, Catalina; Herrera, Diego

2015-11-05

The leading policy to conserve forest is protected areas (PAs). Yet, PAs are not a single tool: land users and uses vary by PA type; and public PA strategies vary in the extent of each type and in the determinants of impact for each type, i.e. siting and internal deforestation. Further, across regions and time, strategies respond to pressures (deforestation and political). We estimate deforestation impacts of PA types for a critical frontier, the Brazilian Amazon. We separate regions and time periods that differ in their deforestation and political pressures and document considerable variation in PA strategies across regions, time periods and types. The siting of PAs varies across regions. For example, all else being equal, PAs in the arc of deforestation are relatively far from non-forest, while in other states they are relatively near. Internal deforestation varies across time periods, e.g. it is more similar across the PA types for PAs after 2000. By contrast, after 2000, PA extent is less similar across PA types with little non-indigenous area created inside the arc. PA strategies generate a range of impacts for PA types--always far higher within the arc--but not a consistent ranking of PA types by impact. © 2015 The Author(s).

Measuring the difference made by conservation initiatives: protected areas and their environmental and social impacts.

Science.gov (United States)

Ferraro, Paul J; Pressey, Robert L

2015-11-05

Success in conservation depends on our ability to reduce human pressures in areas that harbour biological diversity and ecosystem services. Legally protecting some of these areas through the creation of protected areas is a key component of conservation efforts globally. To develop effective protected area networks, practitioners need credible, scientific evidence about the degree to which protected areas affect environmental and social outcomes, and how these effects vary with context. Such evidence has been lacking, but the situation is changing as conservation scientists adopt more sophisticated research designs for evaluating protected areas' past impacts and for predicting their future impacts. Complementing these scientific advances, conservation funders and practitioners are paying increasing attention to evaluating their investments with more scientifically rigorous evaluation designs. This theme issue highlights recent advances in the science of protected area evaluations and explores the challenges to developing a more credible evidence base that can help societies achieve their goals of protecting nature while enhancing human welfare. © 2015 The Author(s).

Improving social impact assessment of protected areas: A review of the literature and directions for future research

Energy Technology Data Exchange (ETDEWEB)

Jones, Nikoleta, E-mail: nikoleta.jones@anglia.ac.uk [Global Sustainability Institute, Anglia Ruskin University, Cambridge (United Kingdom); McGinlay, James, E-mail: jimmcginlay@hotmail.com [School of Water, Energy & Environment, Cranfield University, Cranfield (United Kingdom); Dimitrakopoulos, Panayiotis G., E-mail: pdimi@env.aegean.gr [Biodiversity Conservation Laboratory, Department of Environment, University of the Aegean, 81100 Mytilene, Lesbos Island (Greece)

2017-05-15

Protected areas are the most widely applied policy tool for biodiversity conservation. However, effective management of protected areas is often obstructed by conflicts mainly associated with the social impacts imposed on local communities and other users by their establishment. Despite the importance of these social impacts they remain significantly under-researched. There is now an increasing need to incorporate social impacts in decision making processes by providing accurate estimations and develop ways to forecast their change in the future. Considering the increase of studies identifying this need, the present paper aims to indicate three main directions that will assist in designing effective tools for measuring and most importantly understanding social impacts: a) perceptions on social impacts of individuals who are directly affected by protected areas need to be incorporated in management evaluation techniques in a meaningful and accurate way and be combined with objective measurements of impact; b) understanding the factors determining the actual and perceived levels of social impacts is a key step for the design of effective management frameworks of protected areas and c) social impacts should not be seen as static concepts but should be seen as a dynamic and long-term factor which needs to be incorporated in decision-making processes.

Improving social impact assessment of protected areas: A review of the literature and directions for future research

International Nuclear Information System (INIS)

Jones, Nikoleta; McGinlay, James; Dimitrakopoulos, Panayiotis G.

2017-01-01

Protected areas are the most widely applied policy tool for biodiversity conservation. However, effective management of protected areas is often obstructed by conflicts mainly associated with the social impacts imposed on local communities and other users by their establishment. Despite the importance of these social impacts they remain significantly under-researched. There is now an increasing need to incorporate social impacts in decision making processes by providing accurate estimations and develop ways to forecast their change in the future. Considering the increase of studies identifying this need, the present paper aims to indicate three main directions that will assist in designing effective tools for measuring and most importantly understanding social impacts: a) perceptions on social impacts of individuals who are directly affected by protected areas need to be incorporated in management evaluation techniques in a meaningful and accurate way and be combined with objective measurements of impact; b) understanding the factors determining the actual and perceived levels of social impacts is a key step for the design of effective management frameworks of protected areas and c) social impacts should not be seen as static concepts but should be seen as a dynamic and long-term factor which needs to be incorporated in decision-making processes.

A conservation planning approach to mitigate the impacts of leakage from protected area networks.

Science.gov (United States)

Bode, Michael; Tulloch, Ayesha I T; Mills, Morena; Venter, Oscar; Ando, Amy W

2015-06-01

Protected area networks are designed to restrict anthropogenic pressures in areas of high biodiversity. Resource users respond by seeking to replace some or all of the lost resources from locations elsewhere in the landscape. Protected area networks thereby perturb the pattern of human pressures by displacing extractive effort from within protected areas into the broader landscape, a process known as leakage. The negative effects of leakage on conservation outcomes have been empirically documented and modeled using homogeneous descriptions of conservation landscapes. Human resource use and biodiversity vary greatly in space, however, and a theory of leakage must describe how this heterogeneity affects the magnitude, pattern, and biodiversity impacts of leakage. We combined models of household utility, adaptive human foraging, and biodiversity conservation to provide a bioeconomic model of leakage that accounts for spatial heterogeneity. Leakage had strong and divergent impacts on the performance of protected area networks, undermining biodiversity benefits but mitigating the negative impacts on local resource users. When leakage was present, our model showed that poorly designed protected area networks resulted in a substantial net loss of biodiversity. However, the effects of leakage can be mitigated if they are incorporated ex-ante into the conservation planning process. If protected areas are coupled with nonreserve policy instruments such as market subsidies, our model shows that the trade-offs between biodiversity and human well-being can be further and more directly reduced. © 2014 Society for Conservation Biology.

Modelling of Ballistic Impact over a Ceramic-Metal Protection System

Directory of Open Access Journals (Sweden)

Leandro Neckel

2013-01-01

Full Text Available The behavior of ceramic-metal protection against a projectile impact is modeled. The model takes into account the mass and velocity for each stage of the phenomenon. A former model was modified considering more realistic parameters such as geometries and deformation profile. To analyze the model, simulations on different parameters have been run. The impact results of different ballistic projectiles were simulated, and the movement was plotted. In addition, a deterministic simulation on the mechanical properties of the back metal plate properties was done.

A study on ship impacting a flexible crashworthy device for protecting bridge pier

Directory of Open Access Journals (Sweden)

Yang Liming

2015-01-01

Full Text Available As the accident of a vessel impacting a bridge pier will cause serious disaster, such as destroyed bridge, sinking ship and polluting environment, the technology and method to protect bridge pier from ship collision have been widely investigated recently. Due to the huge kinetic energy of large-tonnage ship and the short time duration in the collision, the studies involve impact mechanics. A developed flexible crashworthy device has been developed to protect bridges, which consists of an outer steel-periphery, an inner steel-periphery and the rubber coating SWRCs(soft elements installed between them. When the SWRC crashworthy device is installed, the collision duration under low impact force is prolonged due to its high compliance, which results in the ship having enough time to turn its navigation direction and most of the remainder kinetic energy being carried off by the turned away ship. Consequently, both impact forces on the ship and on the bridge pier decrease markedly. This is the key reason as to why the SWRC crashworthy device can avoid the destruction of both the bridge and the ship. Based on our results of theoretical studies and numerical simulations, the present paper will propose an experiment-adopted a real ship to impact a flexible crashworthy device. The collision test has been performed 12 times with different speed, carrying capacity, and impact angle of the ship. After the experiments, the ship, flexible crashworthy device and the pier are not damaged. The experiments show that the flexible crashworthy device can turn away the impact ship, so that the ship moves along the outer part of the device, which reduces the ship impact force on the bridge pier obviously. It not only protects bridges but also avoids the damage to ships.

Land-use and land-cover change shape the sustainability and impacts of protected areas.

Science.gov (United States)

Tesfaw, Anteneh T; Pfaff, Alexander; Golden Kroner, Rachel E; Qin, Siyu; Medeiros, Rodrigo; Mascia, Michael B

2018-02-27

Protected areas (PAs) remain the dominant policy to protect biodiversity and ecosystem services but have been shown to have limited impact when development interests force them to locations with lower deforestation pressure. Far less known is that such interests also cause widespread tempering, reduction, or removal of protection [i.e., PA downgrading, downsizing, and degazettement (PADDD)]. We inform responses to PADDD by proposing and testing a bargaining explanation for PADDD risks and deforestation impacts. We examine recent degazettements for hydropower development and rural settlements in the state of Rondônia in the Brazilian Amazon. Results support two hypotheses: ( i ) ineffective PAs (i.e., those where internal deforestation was similar to nearby rates) were more likely to be degazetted and ( ii ) degazettement of ineffective PAs caused limited, if any, additional deforestation. We also report on cases in which ineffective portions were upgraded. Overall our results suggest that enhancing PAs' ecological impacts enhances their legal durability.

Integrated conservation and development: evaluating a community-based marine protected area project for equality of socioeconomic impacts

Science.gov (United States)

Gurney, Georgina G.; Pressey, Robert L.; Cinner, Joshua E.; Pollnac, Richard; Campbell, Stuart J.

2015-01-01

Despite the prevalence of protected areas, evidence of their impacts on people is weak and remains hotly contested in conservation policy. A key question in this debate is whether socioeconomic impacts vary according to social subgroup. Given that social inequity can create conflict and impede poverty reduction, understanding how protected areas differentially affect people is critical to designing them to achieve social and biological goals. Understanding heterogeneous responses to protected areas can improve targeting of management activities and help elucidate the pathways through which impacts of protected areas occur. Here, we assessed whether the socioeconomic impacts of marine protected areas (MPAs)—designed to achieve goals for both conservation and poverty alleviation—differed according to age, gender or religion in associated villages in North Sulawesi, Indonesia. Using data from pre-, mid- and post-implementation of the MPAs for control and project villages, we found little empirical evidence that impacts on five key socioeconomic indicators related to poverty differed according to social subgroup. We found suggestive empirical evidence that the effect of the MPAs on environmental knowledge differed by age and religion; over the medium and long terms, younger people and Muslims showed greater improvements compared with older people and Christians, respectively. PMID:26460130

Integrated conservation and development: evaluating a community-based marine protected area project for equality of socioeconomic impacts.

Science.gov (United States)

Gurney, Georgina G; Pressey, Robert L; Cinner, Joshua E; Pollnac, Richard; Campbell, Stuart J

2015-11-05

Despite the prevalence of protected areas, evidence of their impacts on people is weak and remains hotly contested in conservation policy. A key question in this debate is whether socioeconomic impacts vary according to social subgroup. Given that social inequity can create conflict and impede poverty reduction, understanding how protected areas differentially affect people is critical to designing them to achieve social and biological goals. Understanding heterogeneous responses to protected areas can improve targeting of management activities and help elucidate the pathways through which impacts of protected areas occur. Here, we assessed whether the socioeconomic impacts of marine protected areas (MPAs)-designed to achieve goals for both conservation and poverty alleviation-differed according to age, gender or religion in associated villages in North Sulawesi, Indonesia. Using data from pre-, mid- and post-implementation of the MPAs for control and project villages, we found little empirical evidence that impacts on five key socioeconomic indicators related to poverty differed according to social subgroup. We found suggestive empirical evidence that the effect of the MPAs on environmental knowledge differed by age and religion; over the medium and long terms, younger people and Muslims showed greater improvements compared with older people and Christians, respectively. © 2015 The Author(s).

Fuelwood collection and its impacts on a protected tropical mountain forest in Uganda

NARCIS (Netherlands)

Sassen, M.; Sheil, D.; Giller, K.E.

2015-01-01

Local communities who live close to protected tropical forests often depend on them for woodfuel, their main source of energy. The impacts of fuelwood extraction in humid forests are rarely studied, yet the extraction of wood for fuel can impact forest structure, function and biodiversity. We

Impacts of recreation and tourism on plant biodiversity and vegetation in protected areas in Australia.

Science.gov (United States)

Pickering, Catherine Marina; Hill, Wendy

2007-12-01

This paper reviews recent research into the impact of recreation and tourism in protected areas on plant biodiversity and vegetation communities in Australia. Despite the international significance of the Australian flora and increasing visitation to protected areas there has been limited research on recreational and tourism impacts in Australia. As overseas, there are obvious direct impacts of recreation and tourism such as clearing of vegetation for infrastructure or damage from trampling, horse riding, mountain biking and off road vehicles. As well, there are less obvious but potentially more severe indirect impacts. This includes self-propagating impacts associated with the spread of some weeds from trails and roads. It also includes the severe impact on native vegetation, including many rare and threatened plants, from spread of the root rot fungus Phytopthora cinnamomi. This review highlights the need for more recreational ecology research in Australia.

A Dosimetric Evaluation of Conventional Helmet Field Irradiation Versus Two-Field Intensity-Modulated Radiotherapy Technique

International Nuclear Information System (INIS)

Yu, James B.; Shiao, Stephen L.; Knisely, Jonathan

2007-01-01

Purpose: To compare dosimetric differences between conventional two-beam helmet field irradiation (external beam radiotherapy, EBRT) of the brain and a two-field intensity-modulated radiotherapy (IMRT) technique. Methods and Materials: Ten patients who received helmet field irradiation at our institution were selected for study. External beam radiotherapy portals were planned per usual practice. Intensity-modulated radiotherapy fields were created using the identical field angles as the EBRT portals. Each brain was fully contoured along with the spinal cord to the bottom of the C2 vertebral body. This volume was then expanded symmetrically by 0.5 cm to construct the planning target volume. An IMRT plan was constructed using uniform optimization constraints. For both techniques, the nominal prescribed dose was 3,000 cGy in 10 fractions of 300 cGy using 6-MV photons. Comparative dose-volume histograms were generated for each patient and analyzed. Results: Intensity-modulated radiotherapy improved dose uniformity over EBRT for whole brain radiotherapy. The mean percentage of brain receiving >105% of dose was reduced from 29.3% with EBRT to 0.03% with IMRT. The mean maximum dose was reduced from 3,378 cGy (113%) for EBRT to 3,162 cGy (105%) with IMRT. The mean percent volume receiving at least 98% of the prescribed dose was 99.5% for the conventional technique and 100% for IMRT. Conclusions: Intensity-modulated radiotherapy reduces dose inhomogeneity, particularly for the midline frontal lobe structures where hot spots occur with conventional two-field EBRT. More study needs to be done addressing the clinical implications of optimizing dose uniformity and its effect on long-term cognitive function in selected long-lived patients

Detection of impact damage on thermal protection systems using thin-film piezoelectric sensors for integrated structural health monitoring

Science.gov (United States)

Na, Jeong K.; Kuhr, Samuel J.; Jata, Kumar V.

2008-03-01

Thermal Protection Systems (TPS) can be subjected to impact damage during flight and/or during ground maintenance and/or repair. AFRL/RXLP is developing a reliable and robust on-board sensing/monitoring capability for next generation thermal protection systems to detect and assess impact damage. This study was focused on two classes of metallic thermal protection tiles to determine threshold for impact damage and develop sensing capability of the impacts. Sensors made of PVDF piezoelectric film were employed and tested to evaluate the detectability of impact signals and assess the onset or threshold of impact damage. Testing was performed over a range of impact energy levels, where the sensors were adhered to the back of the specimens. The PVDF signal levels were analyzed and compared to assess damage, where digital microscopy, visual inspection, and white light interferometry were used for damage verification. Based on the impact test results, an assessment of the impact damage thresholds for each type of metallic TPS system was made.

Protection against external impacts and missiles - Load assumption and effects on the plant design of a 1300 MW PWR-Plant

International Nuclear Information System (INIS)

Gremm, O.; Orth, K.H.

1978-01-01

The load assumptions and effects of the external impacts are given. The fundamental properties of the KWU standard design according to these impacts and the consequences for the engineering safeguards are explained. The protection against external impacts includes the protection against all external missiles. The basic measure of protection against internal missiles is the strict separation of redundancies. (author)

Determination of Acreage Thermal Protection Foam Loss From Ice and Foam Impacts

Science.gov (United States)

Carney, Kelly S.; Lawrence, Charles

2015-01-01

A parametric study was conducted to establish Thermal Protection System (TPS) loss from foam and ice impact conditions similar to what might occur on the Space Launch System. This study was based upon the large amount of testing and analysis that was conducted with both ice and foam debris impacts on TPS acreage foam for the Space Shuttle Project External Tank. Test verified material models and modeling techniques that resulted from Space Shuttle related testing were utilized for this parametric study. Parameters varied include projectile mass, impact velocity and impact angle (5 degree and 10 degree impacts). The amount of TPS acreage foam loss as a result of the various impact conditions is presented.

Spectacle-related eye injuries, spectacle-impact performance and eye protection.

Science.gov (United States)

Hoskin, Annette K; Philip, Swetha; Dain, Stephen J; Mackey, David A

2015-05-01

The aim was to review the prevalence of spectacle-related ocular trauma and the performance of currently available spectacle materials and to identify the risk factors associated with spectacle-related ocular trauma. A literature review was conducted using Medline, Embase and Google with the keywords 'eyeglasses' OR 'spectacles' AND 'ocular injury' / 'eye injury'/ 'eye trauma' / 'ocular trauma'. Articles published prior to 1975 were excluded from this review because of advances in spectacle lens technology and Food and Drug Administration legislative changes requiring impact resistance of all prescription spectacle lenses in the United States. Six hundred and ninety-five individual ocular traumas, for which spectacles contributed to or were the main cause of injury, were identified in the literature. Eye injuries occurred when spectacles were worn in sports, in which medium- to high-impact energies were exerted from balls, racquets or bats and/or as a result of a collision with another player. Frame, lens design and product material choice were found to be associated with ocular injury, with polycarbonate lenses cited as the material of choice in the literature. International, regional and national standards for spectacle lenses had a wide range of impact requirements for prescription spectacle lenses, sports eye protection and occupational eye protection. Spectacle-related injury represents a small but preventable cause of ocular injury. With the increasing numbers of spectacle wearers and calls to spend more time outdoors to reduce myopia, spectacle wearers need to be made aware of the potential risks associated with wearing spectacles during medium- to high-risk activities. At particular risk are those prone to falls, the functionally one-eyed, those who have corneal thinning or have had previous eye surgery or injury. With increased understanding of specific risk factors, performance guidelines can be developed for prescription spectacle eye-protection

The use of environmental impact assessment in protecting the built cultural heritage

DEFF Research Database (Denmark)

Flynn, Errol David

2004-01-01

This article examines the application of the environmental impact assessment as a means of protecting the built and cultural heritage during and after the construction of the new national opera house in the Holmen area of Copenhagen. It assesses the affect the new building has had...... on the surrounding built and cultural heritage and examines how the environmental impact assessment was used during the development process....

Cykelhjelm forebygger hjerneskade

DEFF Research Database (Denmark)

Forsse, Axel; Eskesen, Vagn; Springborg, Jacob Bertram

2015-01-01

that there is scientific evidence of bicycle helmet efficacy with a protective effect on serious brain injury of 63-88%. There is no consensus in favour of the effect of bicycle helmet legislation, although a Cochrane review from 2007 showed a significant reduction of injuries among children....

Determining spherical lens correction for astronaut training underwater.

Science.gov (United States)

Porter, Jason; Gibson, C Robert; Strauss, Samuel

2011-09-01

To develop a model that will accurately predict the distance spherical lens correction needed to be worn by National Aeronautics and Space Administration astronauts while training underwater. The replica space suit's helmet contains curved visors that induce refractive power when submersed in water. Anterior surface powers and thicknesses were measured for the helmet's protective and inside visors. The impact of each visor on the helmet's refractive power in water was analyzed using thick lens calculations and Zemax optical design software. Using geometrical optics approximations, a model was developed to determine the optimal distance spherical power needed to be worn underwater based on the helmet's total induced spherical power underwater and the astronaut's manifest spectacle plane correction in air. The validity of the model was tested using data from both eyes of 10 astronauts who trained underwater. The helmet's visors induced a total power of -2.737 D when placed underwater. The required underwater spherical correction (FW) was linearly related to the spectacle plane spherical correction in air (FAir): FW = FAir + 2.356 D. The mean magnitude of the difference between the actual correction worn underwater and the calculated underwater correction was 0.20 ± 0.11 D. The actual and calculated values were highly correlated (r = 0.971) with 70% of eyes having a difference in magnitude of astronauts. The model accurately predicts the actual values worn underwater and can be applied (more generally) to determine a suitable spectacle lens correction to be worn behind other types of masks when submerged underwater.

Fatal Cervical Spine Injury Following a Bicycle Crash

Directory of Open Access Journals (Sweden)

Uhrenholt Lars

2017-06-01

Full Text Available Spinal injury following direct loading of the head and neck is a rare sequel of bicycle crashes. Fatal head injuries following bicycle crashes have been described in great detail and safety measures such as bicycle helmets have been developed accordingly. Less frequently, however, potentially severe cervical spine injuries have been described. We present the case of a middle-aged female who sustained an ultimately fatal cervical spine injury following a collision with a car whilst biking wearing a helmet. We discuss the literature regarding the protective effects of bicycle helmets, the relevance to cervical spine injury and legislation on mandatory use of helmets for injury prevention.

Analysis of NPP protection structure reliability under impact of a falling aircraft

International Nuclear Information System (INIS)

Shul'man, G.S.

1996-01-01

Methodology for evaluation of NPP protection structure reliability by impact of aircraft fall down is considered. The methodology is base on the probabilistic analysis of all potential events. The problem is solved in three stages: determination of loads on structural units, calculation of local reliability of protection structures by assigned loads and estimation of the structure reliability. The methodology proposed may be applied at the NPP design stage and by determination of reliability of already available structures

Impact of vaccine herd-protection effects in cost-effectiveness analyses of childhood vaccinations. A quantitative comparative analysis.

Science.gov (United States)

Holubar, Marisa; Stavroulakis, Maria Christina; Maldonado, Yvonne; Ioannidis, John P A; Contopoulos-Ioannidis, Despina

2017-01-01

Inclusion of vaccine herd-protection effects in cost-effectiveness analyses (CEAs) can impact the CEAs-conclusions. However, empirical epidemiologic data on the size of herd-protection effects from original studies are limited. We performed a quantitative comparative analysis of the impact of herd-protection effects in CEAs for four childhood vaccinations (pneumococcal, meningococcal, rotavirus and influenza). We considered CEAs reporting incremental-cost-effectiveness-ratios (ICERs) (per quality-adjusted-life-years [QALY] gained; per life-years [LY] gained or per disability-adjusted-life-years [DALY] avoided), both with and without herd protection, while keeping all other model parameters stable. We calculated the size of the ICER-differences without vs with-herd-protection and estimated how often inclusion of herd-protection led to crossing of the cost-effectiveness threshold (of an assumed societal-willingness-to-pay) of $50,000 for more-developed countries or X3GDP/capita (WHO-threshold) for less-developed countries. We identified 35 CEA studies (20 pneumococcal, 4 meningococcal, 8 rotavirus and 3 influenza vaccines) with 99 ICER-analyses (55 per-QALY, 27 per-LY and 17 per-DALY). The median ICER-absolute differences per QALY, LY and DALY (without minus with herd-protection) were $15,620 (IQR: $877 to $48,376); $54,871 (IQR: $787 to $115,026) and $49 (IQR: $15 to $1,636) respectively. When the target-vaccination strategy was not cost-saving without herd-protection, inclusion of herd-protection always resulted in more favorable results. In CEAs that had ICERs above the cost-effectiveness threshold without herd-protection, inclusion of herd-protection led to crossing of that threshold in 45% of the cases. This impacted only CEAs for more developed countries, as all but one CEAs for less developed countries had ICERs below the WHO-cost-effectiveness threshold even without herd-protection. In several analyses, recommendation for the adoption of the target

Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

International Nuclear Information System (INIS)

Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

2008-01-01

The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

The Impact of the Protection of Human Subjects on Research. Working Paper No. 70.

Science.gov (United States)

Halpern, Andrew S.

The author discusses the experimenter's responsibility for the protection of human subjects (such as the handicapped) in research and the impact of this responsibility on methods of doing research. Considered are the types of human rights that are most frequently in need of protection within a research setting (such as the right to privacy); the…

An evaluation of the impact of 'Lifeskills' training on road safety, substance use and hospital attendance in adolescence.

Science.gov (United States)

Teyhan, Alison; Cornish, Rosie; Macleod, John; Boyd, Andy; Doerner, Rita; Sissons Joshi, Mary

2016-01-01

To evaluate if attendance at Lifeskills, a safety education centre for children in Year 6 (10-11 years), is associated with engagement in safer behaviours, and with fewer accidents and injuries, in adolescence. The sample are participants in the Avon Longitudinal Study of Parents and Children who attended school in the Lifeskills catchment area in Year 6; 60% attended Lifeskills. At 14-15 years, participants (n approximately 3000, varies by outcome) self-reported road safety behaviours and accidents, and perceived health effects and use of alcohol, cannabis, and tobacco. Additional outcomes from linkage to Hospital Episodes Statistics were available for a sub-sample (n=1768): hospital admittance (for accident-related reason, from 11-16 years) and A&E attendance (for any reason, from approximately 14-16 years). Children who attended Lifeskills were more likely to report using pedestrian crossings on their way to school than children who did not attend (59% versus 52%). Lifeskills attendance was unrelated to the ownership of cycle helmets, or the use of cycle helmets, seat belts, or reflective/fluorescent clothing, or to A&E attendance. Use of cycle helmets (37%) and reflective/fluorescent clothing (<4%) on last cycle was low irrespective of Lifeskills attendance. Lifeskills attendance was associated with less reported smoking and cannabis use, but was generally unrelated to perceptions of the health impact of substance use. Lifeskills attendance was associated with some safer behaviours in adolescence. The overall low use of cycle helmets and reflective/fluorescent clothing evidences the need for powerful promotion of some safer behaviours at Lifeskills and at follow-up in schools. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Impacts of human recreation on carnivores in protected areas.

Science.gov (United States)

Baker, Angela Darnell; Leberg, Paul L

2018-01-01

Mammalian carnivores can be particularly sensitive to human disturbance, even within protected areas (PAs). Our objective was to understand how human disturbance affects carnivore communities in southern Arizona, USA by studying habitat occupancy based on data collected using non-invasive methods in three PAs with different levels of human disturbance. Carnivore occupancy varied based on human disturbance variables (i.e., roads, trails, etc.). Common carnivore species (coyotes, gray foxes, and bobcats) had high occupancy probability in highly disturbed sites, while all other carnivore species had a higher probability of occupancy in low disturbance protected areas. Additionally, overall carnivore diversity was higher in PAs with low human disturbance. Edges of PAs appeared to negatively impact occupancy of nearly all carnivore species. We also found the presence of roads and trails, and not necessarily how much they are used, had a significant negative impact on the occupancy of most carnivore species. Furthermore, the overall level of disturbance within a PA influenced how sensitive carnivores were to human disturbance variables. Carnivores were more sensitive in PAs with higher levels of disturbance and were relatively unaffected by disturbance variables in a PA with low base levels of disturbance. Increased visitation to PAs, expected with the region's high level of population growth, is likely to cause shifts in the carnivore communities favoring species that are less sensitive to disturbance.

Projected impacts of climate change on a continent-wide protected area network

DEFF Research Database (Denmark)

Hole, David G; Willis, Stephen G; Pain, Deborah J

2009-01-01

Despite widespread concern, the continuing effectiveness of networks of protected areas under projected 21st century climate change is uncertain. Shifts in species' distributions could mean these resources will cease to afford protection to those species for which they were originally established...... species). Persistence of suitable climate space across the network as a whole, however, is notably high, with 88-92% of priority species retaining suitable climate space in >or= 1 IBA(s) in which they are currently found. Only 7-8 priority species lose climatic representation from the network. Hence......, despite the likelihood of significant community disruption, we demonstrate that rigorously defined networks of protected areas can play a key role in mitigating the worst impacts of climate change on biodiversity....

[Prevention of injuries associated with horseback riding].

Science.gov (United States)

ten Kate, Chantal A; de Kooter, Tabitha A; Kramer, William L M

2015-01-01

Each year 9,900 equestrians present at Accident and Emergency Departments, 40% of them 10-19 year old females. The most common horse-riding injuries are to the head, brain, neck and face, torso and extremities. Because of the relatively larger head, children more often fall on their head. Wearing a helmet gives considerable protection. Despite the common use of a helmet by horseback riders, serious head injury still occurs regularly. Further research into improvement of the protective function of the helmet is indicated. The current safety vest (body protector) does not significantly reduce the risk of torso injury. Improvement of its protective function is necessary. Injury to the lower extremities is caused when they become trapped in the stirrup in a fall from or with the horse. Safety stirrups and sturdy footwear are possible preventive measures. Investment in the quality and promotion of preventive measures could reduce the frequency and severity of equestrian injuries.

Is protective equipment useful in preventing concussion? A systematic review of the literature.

Science.gov (United States)

Benson, B W; Hamilton, G M; Meeuwisse, W H; McCrory, P; Dvorak, J

2009-05-01

To determine if there is evidence that equipment use reduces sport concussion risk and/or severity. 12 electronic databases were searched using a combination of Medical Subject Headings and text words to identify relevant articles. Specific inclusion and exclusion criteria were used to select studies for review. Data extracted included design, study population, exposure/outcome measures and results. The quality of evidence was assessed based on epidemiologic criteria regarding internal and external validity (ie, strength of design, sample size/power calculation, selection bias, misclassification bias, control of potential confounding and effect modification). In total, 51 studies were selected for review. A comparison between studies was difficult due to the variability in research designs, definition of concussion, mouthguard/helmet/headgear/face shield types, measurements used to assess exposure and outcomes, and variety of sports assessed. The majority of studies were observational, with 23 analytical epidemiologic designs related to the subject area. Selection bias was a concern in the reviewed studies, as was the lack of measurement and control for potentially confounding variables. There is evidence that helmet use reduces head injury risk in skiing, snowboarding and bicycling, but the effect on concussion risk is inconclusive. No strong evidence exists for the use of mouthguards or face shields to reduce concussion risk. Evidence is provided to suggest that full facial protection in ice hockey may reduce concussion severity, as measured by time loss from competition.

Hiking trails and tourism impact assessment in protected area: Jiuzhaigou Biosphere Reserve, China.

Science.gov (United States)

Li, Wenjun; Ge, Xiaodong; Liu, Chunyan

2005-09-01

More and more visitors are attracted to protected areas nowadays, which not only bring about economic increase but also seriously adverse impacts on the ecological environment. In protected areas, trails are linkage between visitors and natural ecosystem, so they concentrate most of the adverse impacts caused by visitors. The trampling problems on the trails have been received attentions in the tremendous researches. However, few of them have correlated the environmental impacts to trail spatial patterns. In this project, the trails were selected as assessment objective, the trampling problems trail widening, multiple trail, and root exposure were taken as assessment indicators to assess ecological impacts in the case study area Jiuzhaigou Biosphere Reserve, and two spatial index, connectivity and circularity, were taken to indicate the trail network spatial patterns. The research results showed that the appearing frequency of the trampling problems had inverse correlation with the circularity and connectivity of the trail network, while the problem extent had no correlation with the spatial pattern. Comparing with the pristine trails, the artificial maintenance for the trails such as wooden trails and flagstone trails could prohibit vegetation root from exposure effectively. The research finds will be useful for the future trail design and tourism management.

A multiscale method for assessing vegetation baseline of Environmental Impact Assessment (EIA) in protected areas of Chile

Science.gov (United States)

Anibal Pauchard; Eduardo Ugarte; Jaime Millan

2000-01-01

The exponential growth of recreation and tourism or ecotourism activities is affecting ecological processes in protected areas of Chile. In order to protect protected areas integrity, all projects inside their boundaries must pass through the Environmental Impact Assessment (EIA). The purpose of this research was to design a multiscale method to assess vegetation for...

Ship impact against protection islands

DEFF Research Database (Denmark)

Pedersen, Preben Terndrup

1997-01-01

The five most exposed piers and the anchor blocks on the East Bridge shall be protected by aritificial islands. Extensive analytical and experimental investitations were carried out to verify the efficiency of how these protection works....

Designing physical protection technology for insider protection

International Nuclear Information System (INIS)

Trujillo, A.A.; Waddoups, I.G.

1986-01-01

Since its inception, the nuclear industry has been engaged in providing protection against an insider threat. Although insider protection activities have been fairly successful in the past, present societal conditions require increased protection to further minimize the existence of an insider or the consequences of an insider-perpetrated incident. Integration of insider protection techniques into existing administrative and operational procedures has resulted in economic and operational impacts. Future increases in insider protection may result in even greater impacts, so we must proceed wisely as new approaches are developed. Increased emphasis on background investigations, security clearances, human reliability programs, security awareness activities, and the development of technology to address the insider threat are evidence of continuing concern in this area. Experience ranging from operational test and evaluation of developmental equipment to conceptual designs for new facilities has led to the development of general principles and conclusions for mitigating the insider threat while minimizing adverse impacts on site operations. Important principles include real-time monitoring of personnel and material and requiring that the physical protection and material control and accounting systems to be much more coordinated and integrated than in the past

Exercise and Prebiotics Produce Stress Resistance: Converging Impacts on Stress-Protective and Butyrate-Producing Gut Bacteria.

Science.gov (United States)

Mika, A; Rumian, N; Loughridge, A B; Fleshner, M

2016-01-01

The gut microbial ecosystem can mediate the negative health impacts of stress on the host. Stressor-induced disruptions in microbial ecology (dysbiosis) can lead to maladaptive health effects, while certain probiotic organisms and their metabolites can protect against these negative impacts. Prebiotic diets and exercise are feasible and cost-effective strategies that can increase stress-protective bacteria and produce resistance against the detrimental behavioral and neurobiological impacts of stress. The goal of this review is to describe research demonstrating that both prebiotic diets and exercise produce adaptations in gut ecology and the brain that arm the organism against inescapable stress-induced learned helplessness. The results of this research support the novel hypothesis that some of the stress-protective effects of prebiotics and exercise are due to increases in stress-protective gut microbial species and their metabolites. In addition, new evidence also suggests that prebiotic diet or exercise interventions are most effective if given early in life (juvenile-adolescence) when both the gut microbial ecosystem and the brain are plastic. Based on our new understanding of the mechanistic convergence of these interventions, it is feasible to propose that in adults, both interventions delivered in combination may elevate their efficacy to promote a stress-resistant phenotype. © 2016 Elsevier Inc. All rights reserved.

[Application of classified protection of information security in the information system of air pollution and health impact monitoring].

Science.gov (United States)

Hao, Shuxin; Lü, Yiran; Liu, Jie; Liu, Yue; Xu, Dongqun

2018-01-01

To study the application of classified protection of information security in the information system of air pollution and health impact monitoring, so as to solve the possible safety risk of the information system. According to the relevant national standards and requirements for the information system security classified protection, and the professional characteristics of the information system, to design and implement the security architecture of information system, also to determine the protection level of information system. Basic security measures for the information system were developed in the technical safety and management safety aspects according to the protection levels, which effectively prevented the security risk of the information system. The information system established relatively complete information security protection measures, to enhanced the security of professional information and system service, and to ensure the safety of air pollution and health impact monitoring project carried out smoothly.

Descriptive Characteristics of Concussions in National Football League Games, 2010-2011 to 2013-2014.

Science.gov (United States)

Clark, Michael D; Asken, Breton M; Marshall, Stephen W; Guskiewicz, Kevin M

2017-03-01

Despite a high reported incidence rate of concussion, little is known about the on-field characteristics of injurious head impacts in National Football League (NFL) games. To characterize on-field features (location, player position, and time during game) and biomechanical features (anticipation status, closing distance, impact location and type) associated with concussions in NFL games over a 4-season period (2010-2011 to 2013-2014). Descriptive epidemiology study. We analyzed video of a subset of reported, in-game concussions for the 2010-2011 to 2013-2014 seasons. These videos represented a sample of injuries that were diagnosed and reported on the same day and that could be clearly associated with an in-game collision as captured on video. We determined anticipation status, closing distance, impact location on the injured player's helmet, and impact type (helmet-to-helmet, helmet-to-body, or helmet-to-ground). Associations between these variables were analyzed by use of descriptive statistics and tests of association. A total of 871 diagnosed concussions were reported as occurring during NFL preseason, regular season, and postseason games for the 2010-2011, 2011-2012, 2012-2013, and 2013-2014 seasons. A total of 1324 games were played during this period, giving a concussion incidence rate of 0.658 per game (95% CI, 0.61-0.70). From the video-reviewed subset (n = 429; 49.3%), the majority of injurious impacts occurred with good anticipation (57.3%) and concussions in the NFL occurred through a diverse variety of mechanisms, surprisingly tended to be well-anticipated, and, also surprisingly, occurred with concussion were broadly distributed over the helmet. More concussions occurred during the second half of game play, but we do not have evidence to explain this finding.

Assessment of Light Pollution Impact on Protected Areas in China

Science.gov (United States)

Jiang, W.; He, G.; Ni, Y.

2017-09-01

The Protected Areas (PAs) with natural, ecological and cultural value play important role in biological processes, biodiversity and ecosystem service. During the past years of rapid urban expansion in China, the spatial range and intensity of light pollution unprecedented increase. Historically, optical remote sensing and field survey data had been used to reveal that human activities impacted on PAs for individual areas and few papers documented the issue of light pollution impact on PAs at national scale. Here, time series night-time light satellite images of Defense Meteorological Satellite Program Operational Linescan System (DMSP-OLS) were selected to assess the light pollution impacted on PAs in China. The method we proposed can be effectively applied to assess the impact of light pollution on PAs and the percent of dark PAs decreased by 35.38 % from 1992 to 2012 at nationwide. The trend of light pollution of most PAs in stable, however, light pollution of the local area is increase significantly, especially in northern Xinjiang, Gansu, Xizang, Yunnan, Jiangsu and Shandong. Considering the current status of light pollution encroach into PAs, two strategies of appropriate buffer zone and wide measured for light pollution are also recommend.

Motorcycle protective clothing: protection from injury or just the weather?

Science.gov (United States)

de Rome, Liz; Ivers, Rebecca; Fitzharris, Michael; Du, Wei; Haworth, Narelle; Heritier, Stephane; Richardson, Drew

2011-11-01

Apart from helmets, little is known about the effectiveness of motorcycle protective clothing in reducing injuries in crashes. The study aimed to quantify the association between usage of motorcycle clothing and injury in crashes. Cross-sectional analytic study. Crashed motorcyclists (n=212, 71% of identified eligible cases) were recruited through hospitals and motorcycle repair services. Data was obtained through structured face-to-face interviews. The main outcome was hospitalization and motorcycle crash-related injury. Poisson regression was used to estimate relative risk (RR) and 95% confidence intervals for injury adjusting for potential confounders. Motorcyclists were significantly less likely to be admitted to hospital if they crashed wearing motorcycle jackets (RR=0.79, 95% CI: 0.69-0.91), pants (RR=0.49, 95% CI: 0.25-0.94), or gloves (RR=0.41, 95% CI: 0.26-0.66). When garments included fitted body armour there was a significantly reduced risk of injury to the upper body (RR=0.77, 95% CI: 0.66-0.89), hands and wrists (RR=0.55, 95% CI: 0.38-0.81), legs (RR=0.60, 95% CI: 0.40-0.90), feet and ankles (RR=0.54, 95% CI: 0.35-0.83). Non-motorcycle boots were also associated with a reduced risk of injury compared to shoes or joggers (RR=0.46, 95% CI: 0.28-0.75). No association between use of body armour and risk of fracture injuries was detected. A substantial proportion of motorcycle designed gloves (25.7%), jackets (29.7%) and pants (28.1%) were assessed to have failed due to material damage in the crash. Motorcycle protective clothing is associated with reduced risk and severity of crash related injury and hospitalization, particularly when fitted with body armour. The proportion of clothing items that failed under crash conditions indicates a need for improved quality control. While mandating usage of protective clothing is not recommended, consideration could be given to providing incentives for usage of protective clothing, such as tax exemptions for safety

Framework for Proliferation Resistance and Physical Protection for Nonproliferation Impact Assessments

International Nuclear Information System (INIS)

Bari, R.

2008-01-01

This report describes a framework for proliferation resistance and physical protection evaluation for the fuel cycle systems envisioned in the expansion of nuclear power for electricity generation. The methodology is based on an approach developed as part of the Generation IV technical evaluation framework and on a qualitative evaluation approach to policy factors similar to those that were introduced in previous Nonproliferation Impact Assessments performed by DOE

Space Shuttle Thermal Protection System Repair Flight Experiment Induced Contamination Impacts

Science.gov (United States)

Smith, Kendall A.; Soares, Carlos E.; Mikatarian, Ron; Schmidl, Danny; Campbell, Colin; Koontz, Steven; Engle, Michael; McCroskey, Doug; Garrett, Jeff

2006-01-01

NASA s activities to prepare for Flight LF1 (STS-114) included development of a method to repair the Thermal Protection System (TPS) of the Orbiter s leading edge should it be damaged during ascent by impacts from foam, ice, etc . Reinforced Carbon-Carbon (RCC) is used for the leading edge TPS. The repair material that was developed is named Non- Oxide Adhesive eXperimental (NOAX). NOAX is an uncured adhesive material that acts as an ablative repair material. NOAX completes curing during the Orbiter s descent. The Thermal Protection System (TPS) Detailed Test Objective 848 (DTO 848) performed on Flight LF1 (STS-114) characterized the working life, porosity void size in a micro-gravity environment, and the on-orbit performance of the repairs to pre-damaged samples. DTO 848 is also scheduled for Flight ULF1.1 (STS-121) for further characterization of NOAX on-orbit performance. Due to the high material outgassing rates of the NOAX material and concerns with contamination impacts to optically sensitive surfaces, ASTM E 1559 outgassing tests were performed to determine NOAX condensable outgassing rates as a function of time and temperature. Sensitive surfaces of concern include the Extravehicular Mobility Unit (EMU) visor, cameras, and other sensors in proximity to the experiment during the initial time after application. This paper discusses NOAX outgassing characteristics, how the amount of deposition on optically sensitive surfaces while the NOAX is being manipulated on the pre-damaged RCC samples was determined by analysis, and how flight rules were developed to protect those optically sensitive surfaces from excessive contamination where necessary.

Impacts of Community Forest Management and Strictly Protected Areas on Deforestation and Human Well-Being in Madagascar

DEFF Research Database (Denmark)

Rasolofoson, Ranaivo Andriarilala

they contain) and human well-being. However, while scientifically rigorous impact evaluation of programs is well advanced in fields such as development, health and education, it is rare in nature conservation. The rare existing studies focus mostly on protected areas and other interventions, such as CFM......, conditional on household proximity to forest and education level. In conclusion, the impacts of CFM vary with household characteristics: some may lose while others may gain. iii) The potential of the Global Person Generated Index (GPGI) for evaluating the perceived impact of conservation interventions......Protected areas and Community Forest Management (CFM) are among the most widespread interventions to conserve forests in tropical countries. In addition to their impacts on forests and the biodiversity they contain, these interventions also affect human well-being, particularly that of the local...

Determining the Impact of Steady-State PV Fault Current Injections on Distribution Protection

Energy Technology Data Exchange (ETDEWEB)

Seuss, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Reno, Matthew J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Broderick, Robert Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grijalva, Santiago [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

This report investigates the fault current contribution from a single large PV system and the impact it has on existing distribution overcurrent protection devices. Assumptions are made about the modeling of the PV system under fault to perform exhaustive steady - state fault analyses throughout distribution feeder models. Each PV interconnection location is tested to determine how the size of the PV system affects the fault current measured by each protection device. This data is then searched for logical conditions that indicate whether a protection device has operated in a manner that will cause more customer outages due to the addition of the PV system. This is referred to as a protection issue , and there are four unique types of issues that have been identified in the study. The PV system size at which any issues occur are recorded to determine the feeder's PV hosting capacity limitations due to interference with protection settings. The analysis is carried out on six feeder models. The report concludes with a discussion of the prevalence and cause of each protection issue caused by PV system fault current.

The impact of parental knowledge and tanning attitudes on sun protection practice for young children in Germany.

Science.gov (United States)

Gefeller, Olaf; Li, Jiang; Uter, Wolfgang; Pfahlberg, Annette B

2014-05-05

Public health campaigns have improved knowledge on UVR-associated skin cancer risk and increased sun protection awareness. However, tanned skin is still a common beauty ideal. The relationship between knowledge, attitudes and protective behavior is not fully understood yet. A population-based survey was thus performed in the district of Erlangen involving 2,619 parents of 3- to 6-year old children. By means of a self-administered standardized questionnaire parental knowledge about risk factors for skin cancer, their attitudes towards tanning and details of protective measures taken for their children were assessed. The study analyzed specifically the impact of parental tanning attitudes on sun-protective measures for their children while controlling for parental knowledge about skin cancer risk factors. While parental knowledge was significantly (inversely) associated with agreement to the statement "Tanned skin is healthy skin", this was not the case for "Tanning makes me look better". Overall, tanning affirmative attitudes were inversely associated with protective measures taken for the children, whereas parental knowledge had a positive impact on sun protection at the beach only. Multivariable analyses provided evidence for an effect of parental attitude on protective behavior independent of parental knowledge. Tanning attitudes and tanned skin as the misguided ideal of beauty need to be addressed in future public health campaigns to enhance the effectiveness of preventive activities in changing sun protective behavior.

The Impact of Parental Knowledge and Tanning Attitudes on Sun Protection Practice for Young Children in Germany

Directory of Open Access Journals (Sweden)

Olaf Gefeller

2014-05-01

Full Text Available Public health campaigns have improved knowledge on UVR-associated skin cancer risk and increased sun protection awareness. However, tanned skin is still a common beauty ideal. The relationship between knowledge, attitudes and protective behavior is not fully understood yet. A population-based survey was thus performed in the district of Erlangen involving 2,619 parents of 3- to 6-year old children. By means of a self-administered standardized questionnaire parental knowledge about risk factors for skin cancer, their attitudes towards tanning and details of protective measures taken for their children were assessed. The study analyzed specifically the impact of parental tanning attitudes on sun-protective measures for their children while controlling for parental knowledge about skin cancer risk factors. While parental knowledge was significantly (inversely associated with agreement to the statement “Tanned skin is healthy skin”, this was not the case for “Tanning makes me look better”. Overall, tanning affirmative attitudes were inversely associated with protective measures taken for the children, whereas parental knowledge had a positive impact on sun protection at the beach only. Multivariable analyses provided evidence for an effect of parental attitude on protective behavior independent of parental knowledge. Tanning attitudes and tanned skin as the misguided ideal of beauty need to be addressed in future public health campaigns to enhance the effectiveness of preventive activities in changing sun protective behavior.

When is protection from impact needed for the face as well as the eyes in occupational environments?

Science.gov (United States)

Dain, Stephen J; Huang, Rose; Tiao, Aimee; Chou, B Ralph

2018-05-01

The most commonly identified reason for requiring or using occupational eye and face protection is for protection against flying objects. Standards vary on what risk may require protection of the eyes alone and what requires protection for the whole face. Information on the minimum energy transfer for face damage to occur is not well-established. The heads of pigs were used as the common model for human skin. A 6 mm steel ball projected at velocities between 45 and 135 m/s was directed at the face area. Examples of impacts were filmed with a high-speed camera and the resulting damage was rated visually on a scale from 1 (no visible damage) to 5 (penetrated the skin and embedded in the flesh). The results for the cheek area indicate that 85 m/s is the velocity above which damage is more likely to occur unless the skin near the lip is included. For damage to the lip area to be avoided, the velocity needs to be 60 m/s or less. The present data support a maximum impact velocity of 85 m/s, provided the thinner and more vulnerable skin of the lids and orbital adnexa is protected. If the coverage area does not extend to the orbital adnexa, then the absolute upper limit for the velocity is 60 m/s. At this stage, eye-only protection, as represented by the lowest level of impact test in the standards in the form of a drop ball test, is not in question. © 2017 Optometry Australia.

Exploring the impacts of protected area tourism on local communities using a resilience approach

Directory of Open Access Journals (Sweden)

Jennifer Strickland-Munro

2014-06-01

Full Text Available As the protected area mandate expands to include social equity, the impacts of parks and their tourism on neighbouring indigenous and local communities is receiving growing practical and theoretical interest. This article reported on one such study, which explored the impacts of protected area tourism on communities bordering the iconic Kruger National Park in South Africa and Purnululu National Park in Australia. The study drew on interviews with park staff, tourism operators and community members. Guided by a conceptual framework grounded in resilience thinking, interactions amongst the parks, tourism and local communities were revealed as complex, contested and multi-scalar. Underlying drivers included cultural norms and values based on nature, entrenched poverty, poor Western education and economic opportunities associated with tourism. Park tourism offered intrinsic opportunities and benefits from nature conservation and associated intangible cultural values. More tangible benefits arose through employment. Damage-causing animals and visitation difficulties were negative impacts. Interaction with tourists was limited, with a sense of disconnect evident. Findings indicated the need for multifaceted, carefully considered policy responses if social equity and benefits for local communities are to be achieved. Framing the impacts of protected area tourism through the resilience framework provided a useful way to access local community perceptions whilst retaining awareness of the broader multi-scalar context in which interactions occur. Conservation implications: Perceptions of separation and lack of education to engage in economic opportunities are major issues. Intrinsic appreciation of parks is an important platform for building future opportunities. Accrual of future benefits for local communities from park tourism depends on developing diverse economic opportunities, building community capacity and managing expectations and addressing

Hybrid III anthropomorphic test device (ATD) response to head impacts and potential implications for athletic headgear testing.

Science.gov (United States)

Bartsch, Adam; Benzel, Edward; Miele, Vincent; Morr, Douglas; Prakash, Vikas

2012-09-01

The Hybrid III 50th percentile male anthropomorphic test device (ATD) is the most widely used human impact testing surrogate and has historically been used in automotive or military testing. More recently, this ATD is finding use in applications evaluating athletic helmet protectivity, quantifying head impact dosage and estimating injury risk. But ATD head-neck response has not been quantified in omnidirectional athletic-type head impacts absent axial preload. It is probable that headgear injury reduction that can be quantified in a laboratory, including in American football, boxing, hockey, lacrosse and soccer, is related to a number of interrelated kinetic and kinematic factors, such as head center of gravity linear acceleration, head angular acceleration, head angular velocity, occipito-cervical mechanics and neck stiffness. Therefore, we characterized ATD head-neck dynamic response to direct head impacts in a series of front, oblique front and lateral head impacts. Key findings were: (1) impacts producing highest ATD resultant center of gravity linear acceleration resulted in the lowest resultant occipito-cervical spine bending moment/force. (2) Resultant ATD head angular velocity and angular acceleration did not appear coupled to impact direction at lower impact energy levels; these parameters were coupled at higher energy levels. (3) The ATD had progressively increasing occipito-cervical stiffness in extension, torsion and lateral bending, respectively. Because the ATD neck influenced head and neck impact dosage parameters, testing agencies, manufacturers and researchers should consider using the Hybrid III head form attached to a neck as a means to quantify head and neck injury risks as opposed to systems that do not utilize a neck. This heightened understanding of Hybrid III ATD head-neck response, and consideration of order of stiffest axes in the lateral, oblique and extension directions, respectively, should aid in the development of head and neck injury

The impact of faulty response of overload protection systems on the reliability of electricity supply

International Nuclear Information System (INIS)

Schweigert, J.; Schnuerer, G.

1988-01-01

Protection equipment of the engineered safety system which is to prevent the triggering of actions via signals from the reactor protection system is to be made so reliable that it has no impact on the non-availability of the supplied systems. Design and functional mode of the various overload protection equipment and the relevant switching device and combinations are explained together with the requirements such as choice, design, and adjustment of the protection equipment, followed by a survey of possible causes of faulty response of overload protection device and of the means and measures available for improvement. The now presented version of September 1987 of the 'overload protection report deals basically with all main topics of the Juli 1985 version, but has been updated and extended by material taking into account practice-oriented data on the new developments in convoy power plant design. (orig./HP) [de

A Comprehensive Approach to Motorcycle-Related Head Injury Prevention: Experiences from the Field in Vietnam, Cambodia, and Uganda.

Science.gov (United States)

Craft, Greig; Van Bui, Truong; Sidik, Mirjam; Moore, Danielle; Ederer, David J; Parker, Erin M; Ballesteros, Michael F; Sleet, David A

2017-11-30

Motorcyclists account for 23% of global road traffic deaths and over half of fatalities in countries where motorcycles are the dominant means of transport. Wearing a helmet can reduce the risk of head injury by as much as 69% and death by 42%; however, both child and adult helmet use are low in many countries where motorcycles are a primary mode of transportation. In response to the need to increase helmet use by all drivers and their passengers, the Global Helmet Vaccine Initiative (GHVI) was established to increase helmet use in three countries where a substantial portion of road users are motorcyclists and where helmet use is low. The GHVI approach includes five strategies to increase helmet use: targeted programs, helmet access, public awareness, institutional policies, and monitoring and evaluation. The application of GHVI to Vietnam, Cambodia, and Uganda resulted in four key lessons learned. First, motorcyclists are more likely to wear helmets when helmet use is mandated and enforced. Second, programs targeted to at-risk motorcyclists, such as child passengers, combined with improved awareness among the broader population, can result in greater public support needed to encourage action by decision-makers. Third, for broad population-level change, using multiple strategies in tandem can be more effective than using a single strategy alone. Lastly, the successful expansion of GHVI into Cambodia and Uganda has been hindered by the lack of helmet accessibility and affordability, a core component contributing to its success in Vietnam. This paper will review the development of the GHVI five-pillar approach in Vietnam, subsequent efforts to implement the model in Cambodia and Uganda, and lessons learned from these applications to protect motorcycle drivers and their adult and child passengers from injury.

Protecting individuals against the negative impact of big data : The potential and limitations of the privacy and data protection law approach

NARCIS (Netherlands)

Oostveen, M.A.A.

2018-01-01

This thesis is about the protection of individuals against the negative impact that big data may have on their private lives. Many positive and promising developments result from big data, but the massive collection and use of data also raise a host of issues. In the European Union, the rights to

Flexible pressure sensors for smart protective clothing against impact loading

International Nuclear Information System (INIS)

Wang, Fei; Zhu, Bo; Shu, Lin; Tao, Xiaoming

2014-01-01

The development of smart protective clothing will facilitate the quick detection of injuries from contact sports, traffic collisions and other accidents. To obtain real-time information like spatial and temporal pressure distributions on the clothing, flexible pressure sensor arrays are required. Based on a resistive fabric strain sensor we demonstrate all flexible, resistive pressure sensors with a large workable pressure range (0–8 MPa), a high sensitivity (1 MPa −1 ) and an excellent repeatability (lowest non-repeatability ±2.4% from 0.8 to 8 MPa) that can be inexpensively fabricated using fabric strain sensors and biocompatible polydimethylsiloxane (PDMS). The pressure sensitivity is tunable by using elastomers with different elasticities or by the pre-strain control of fabric strain sensors. Finite element simulation further confirms the sensor design. The simple structure, large workable pressure range, high sensitivity, high flexibility, facile fabrication and low cost of these pressure sensors make them promising candidates for smart protective clothing against impact loading. (paper)

The Effect of a Monocular Helmet-Mounted Display on Aircrew Health: A Longitudinal Cohort Study of Apache AH Mk 1 Pilots -(Vision and Handedness)

Science.gov (United States)

2015-05-19

the day, night, and in adverse weather through the use of nose-mounted, forward-looking infrared (FLIR) pilotage and targeting sensors that provide a...sensor video and/or symbology to each crewmember via a helmet display unit (HDU). The HDU contains a 1-inch (in.) diameter cathode ray tube (CRT...American Association for Pediatric Ophthalmology and Strabismus, 12(4): 365–369. Sale, D. F., and Lund, G. J. 1993. AH-64 Apache program update

Progress on Protection Strategies to Mitigate the Impact of Renewable Distributed Generation on Distribution Systems

Directory of Open Access Journals (Sweden)

Mohamad Norshahrani

2017-11-01

Full Text Available The benefits of distributed generation (DG based on renewable energy sources leads to its high integration in the distribution network (DN. Despite its well-known benefits, mainly in improving the distribution system reliability and security, there are challenges encountered from a protection system perspective. Traditionally, the design and operation of the protection system are based on a unidirectional power flow in the distribution network. However, the integration of distributed generation causes multidirectional power flows in the system. Therefore, the existing protection systems require some improvement or modification to address this new feature. Various protection strategies for distribution system have been proposed so that the benefits of distributed generation can be fully utilized. This paper reviews the current progress in protection strategies to mitigate the impact of distributed generation in the distribution network. In general, the reviewed strategies in this paper are divided into: (1 conventional protection systems and (2 modifications of the protection systems. A comparative study is presented in terms of the respective benefits, shortcomings and implementation cost. Future directions for research in this area are also presented.

Prenatal forehead edema in 4p- deletion: the 'Greek warrior helmet' profile revisited.

Science.gov (United States)

Levaillant, J M; Touboul, C; Sinico, M; Vergnaud, A; Serero, S; Druart, L; Blondeau, J R; Abd Alsamad, I; Haddad, B; Gérard-Blanluet, M

2005-12-01

Deletion of short arm of chromosome 4 is difficult to ascertain prenatally, and can be missed. A prenatal suspicion of 4p- syndrome was thoroughly investigated by using two-dimensional and three-dimensional sonography, with a description of the fetal face dysmorphological pattern. The cytogenetic confirmation, obtained by karyotype and FISH technique, allowed a precise description of the prenatal abnormalities. Post-termination tridimensional helicoidal scanner of the fetal face was performed. The main anomaly discovered using two-dimensional sonography was the presence of a strikingly thick prefrontal edema (8 mm, twice the normal values, at 22 weeks: 3.81 +/- 0.62 mm). Three-dimensional sonography showed the classical postnatal profile, with the phenotypic aspect of a 'Greek warrior helmet'. Nasal bones were normal in size and placement, confirmed by helicoidal scanner. Prenatal diagnosis of 4p deletion syndrome can be difficult, and it is the presence of prefrontal edema, associated with more subtle facial anomalies (short philtrum, microretrognathia) which should trigger cytogenetic investigation for 4p- deletion, even with only borderline growth retardation. Copyright 2005 John Wiley & Sons, Ltd

The impact of immersion protection requirements on hair dryer electrocutions in the USA.

Science.gov (United States)

Rodgers, Gregory B; Garland, Sarah

2012-12-01

To evaluate the effectiveness of the immersion protection requirements of a voluntary safety standard for portable handheld hair dryers in preventing electrocution deaths in the USA. The present work was an interrupted time series study design. Data on annual hair dryer-related electrocution deaths resulting from water contact were developed for the 1980-2007 study period. A multivariate Poisson regression model for rate data was used to evaluate the impact of the immersion protection requirements during the post-intervention period. The analysis controlled for the estimated number of hair dryers in use and the estimated number of US homes equipped with ground fault circuit interrupters, safety devices that would address hair dryer electrocutions even in the absence of the immersion protection requirements of the voluntary standard. The implementation of the 1987 and 1991 immersion protection requirements of the voluntary standard for portable handheld hair dryers was the intervention studied. The main outcome measure was the estimated reduction in the hair dryer electrocution rate associated with the immersion protection requirements of the voluntary standard. After controlling for covariates, the immersion protection requirements were estimated to reduce the rate of hair dryer immersion electrocution deaths by 96.6% (95% CI, 90.8% to 98.8%). This suggests the prevention of about 280 immersion electrocution deaths involving hair dryers during the post-intervention period (1987-2007). The immersion protection requirements of the voluntary safety standard for hair dryers have been highly effective in reducing hair dryer electrocutions.

Bike Helmets and Black Riders: Experiential Approaches to Helping Students Understand Natural Hazard Assessment and Mitigation Issues

Science.gov (United States)

Stein, S. A.; Kley, J.; Hindle, D.; Friedrich, A. M.

2014-12-01

Defending society against natural hazards is a high-stakes game of chance against nature, involving tough decisions. How should a developing nation allocate its budget between building schools for towns without ones or making existing schools earthquake-resistant? Does it make more sense to build levees to protect against floods, or to prevent development in the areas at risk? Would more lives be saved by making hospitals earthquake-resistant, or using the funds for patient care? These topics are challenging because they are far from normal experience, in that they involve rare events and large sums. To help students in natural hazard classes conceptualize them, we pose tough and thought-provoking questions about complex issues involved and explore them together via lectures, videos, field trips, and in-class and homework questions. We discuss analogous examples from the students' experiences, drawing on a new book "Playing Against Nature, Integrating Science and Economics to Mitigate Natural Hazards in an Uncertain World". Asking whether they wear bicycle helmets and why or why not shows the cultural perception of risk. Individual students' responses vary, and the overall results vary dramatically between the US, UK, and Germany. Challenges in hazard assessment in an uncertain world are illustrated by asking German students whether they buy a ticket on public transportation - accepting a known cost - or "ride black" - not paying but risking a heavy fine if caught. We explore the challenge of balancing mitigation costs and benefits via the question "If you were a student in Los Angeles, how much more would you pay in rent each month to live in an earthquake-safe building?" Students learn that interdisciplinary thinking is needed, and that due to both uncertainties and sociocultural factors, no unique or right strategies exist for a particular community, much the less all communities. However, we can seek robust policies that give sensible results given

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Sadhana. Praveen Kumar Pinnoji. Articles written in Sadhana. Volume 32 Issue 4 August 2007 pp 445-458. Finite element modelling of helmeted head impact under frontal loading · Praveen Kumar Pinnoji Puneet Mahajan · More Details Abstract Fulltext PDF. Finite element models of the head and helmet ...

Research in biomechanics of occupant protection.

Science.gov (United States)

King, A I; Yang, K H

1995-04-01

This paper discusses the biomechanical bases for occupant protection against frontal and side impact. Newton's Laws of Motion are used to illustrate the effect of a crash on restrained and unrestrained occupants, and the concept of ride down is discussed. Occupant protection through the use of energy absorbing materials is described, and the mechanism of injury of some of the more common injuries is explained. The role of the three-point belt and the airbag in frontal protection is discussed along with the potential injuries that can result from the use of these restraint systems. Side impact protection is more difficult to attain but some protection can be derived from the use of padding or a side impact airbag. It is concluded that the front seat occupants are adequately protected against frontal impact if belts are worn in an airbag equipped vehicle. Side impact protection may not be uniform in all vehicles.

Strengthening the composite protective shield of light-weight ship against ballistic impacts: analytical and experimental

Directory of Open Access Journals (Sweden)

I. Jalili

Full Text Available Light and medium protection for small naval vessels guarantees their high performance and safety during the guard duties. In this study, a protective shield fabricated from Dyneema HB25 fibers has been utilized as an add-on layer on the coast guard boat hull. Finite element analyses have been conducted using Chocron's model. Two standards of gun-fire were employed and various thicknesses of the composite layers were examined by ballistic impacts. Afterward, numerical simulations results compared with experiments and revealed a good consistency. Finally, some graphs have been presented to help designers for choosing more convenient shield based on protection and weight characteristics after judgment of vessel requirements.

Client Violence and Its Negative Impacts on Work Attitudes of Child Protection Workers Compared to Community Service Workers

Science.gov (United States)

Shin, Junseob

2011-01-01

This study investigated the prevalence of client violence toward child protection workers and its negative impacts on the work attitudes of those workers compared with community service workers in South Korea. This study is based on the assumption that child protection workers are more vulnerable to violence than are community service workers…

Social protection and the employment contract: the impact on work absence.

Science.gov (United States)

Tompa, Emile; Scott-Marshall, Heather; Fang, Miao

2010-01-01

This study investigates the impact of temporary employment on all-cause sickness absence of one week or more with a focus on how this relationship is moderated by factors related to social protection (job tenure, union membership and firm size). A sample of 5,307 individuals who experienced 9,574 distinct job episodes was drawn from a longitudinal Canadian labour market survey (2000-2004). Duration analysis was undertaken to model the time from the start of a job to the first sickness absence. Specifically, a proportional hazard model was estimated using a complementary log-log function for continuous time processes. Findings showed that temporary employment was associated with a lower rate of sickness absence after controlling for tenure, prior health status, and several other individual and job characteristics. The results suggest that the lack of social protection in temporary jobs is a powerful determinant of absence taking, even in the case of serious health conditions that require an absence of one week or more.

Characterization of viscoelastic materials for low-magnitude blast mitigation

Science.gov (United States)

Bartyczak, S.; Mock, W.

2014-05-01

Recent research indicates that exposure to low amplitude blast waves, such as IED detonation or multiple firings of a weapon, causes damage to brain tissue resulting in Traumatic Brain Injury (TBI) and Post Traumatic Stress Disorder (PTSD). Current combat helmets are not sufficiently protecting warfighters from this danger and the effects are debilitating, costly, and long-lasting. The objective of the present work is to evaluate the blast mitigating behavior of current helmet materials and new materials designed for blast mitigation using a test fixture recently developed at the Naval Surface Warfare Center Dahlgren Division for use with an existing gas gun. The 40-mm-bore gas gun was used as a shock tube to generate blast waves (ranging from 0.5 to 2 bar) in the test fixture mounted on the gun muzzle. A fast opening valve was used to release helium gas from the breech which formed into a blast wave and impacted instrumented targets in the test fixture. Blast attenuation of selected materials was determined through the measurement of stress data in front of and behind the target. Materials evaluated in this research include polyurethane foam from currently fielded US Army and Marine Corps helmets, polyurea 1000, and three hardnesses of Sorbothane (48, 58, and 70 durometer, Shore 00). Polyurea 1000 and 6061-T6 aluminum were used to calibrate the stress gauges.

More strictly protected areas are not necessarily more protective: evidence from Bolivia, Costa Rica, Indonesia, and Thailand

International Nuclear Information System (INIS)

Ferraro, Paul J; Hanauer, Merlin M; Miteva, Daniela A; Pattanayak, Subhrendu K; Canavire-Bacarreza, Gustavo Javier; Sims, Katharine R E

2013-01-01

National parks and other protected areas are at the forefront of global efforts to protect biodiversity and ecosystem services. However, not all protection is equal. Some areas are assigned strict legal protection that permits few extractive human uses. Other protected area designations permit a wider range of uses. Whether strictly protected areas are more effective in achieving environmental objectives is an empirical question: although strictly protected areas legally permit less anthropogenic disturbance, the social conflicts associated with assigning strict protection may lead politicians to assign strict protection to less-threatened areas and may lead citizens or enforcement agents to ignore the strict legal restrictions. We contrast the impacts of strictly and less strictly protected areas in four countries using IUCN designations to measure de jure strictness, data on deforestation to measure outcomes, and a quasi-experimental design to estimate impacts. On average, stricter protection reduced deforestation rates more than less strict protection, but the additional impact was not always large and sometimes arose because of where stricter protection was assigned rather than regulatory strictness per se. We also show that, in protected area studies contrasting y management regimes, there are y 2 policy-relevant impacts, rather than only y, as earlier studies have implied. (letter)

Solar energy development impacts on land cover change and protected areas.

Science.gov (United States)

Hernandez, Rebecca R; Hoffacker, Madison K; Murphy-Mariscal, Michelle L; Wu, Grace C; Allen, Michael F

2015-11-03

Decisions determining the use of land for energy are of exigent concern as land scarcity, the need for ecosystem services, and demands for energy generation have concomitantly increased globally. Utility-scale solar energy (USSE) [i.e., ≥ 1 megawatt (MW)] development requires large quantities of space and land; however, studies quantifying the effect of USSE on land cover change and protected areas are limited. We assessed siting impacts of >160 USSE installations by technology type [photovoltaic (PV) vs. concentrating solar power (CSP)], area (in square kilometers), and capacity (in MW) within the global solar hot spot of the state of California (United States). Additionally, we used the Carnegie Energy and Environmental Compatibility model, a multiple criteria model, to quantify each installation according to environmental and technical compatibility. Last, we evaluated installations according to their proximity to protected areas, including inventoried roadless areas, endangered and threatened species habitat, and federally protected areas. We found the plurality of USSE (6,995 MW) in California is sited in shrublands and scrublands, comprising 375 km(2) of land cover change. Twenty-eight percent of USSE installations are located in croplands and pastures, comprising 155 km(2) of change. Less than 15% of USSE installations are sited in "Compatible" areas. The majority of "Incompatible" USSE power plants are sited far from existing transmission infrastructure, and all USSE installations average at most 7 and 5 km from protected areas, for PV and CSP, respectively. Where energy, food, and conservation goals intersect, environmental compatibility can be achieved when resource opportunities, constraints, and trade-offs are integrated into siting decisions.

Emergent Access to the Airway and Chest in American Football Players.

Science.gov (United States)

Swartz, Erik E; Mihalik, Jason P; Decoster, Laura C; Al-Darraji, Sossan; Bric, Justin

2015-07-01

American football has the highest rate of fatalities and catastrophic injuries of any US sport. The equipment designed to protect athletes from these catastrophic events challenges the ability of medical personnel to obtain neutral spine alignment and immobilization during airway and chest access for emergency life-support delivery. To compare motion, time, and difficulty during removal of American football helmets, face masks, and shoulder pads. Quasi-experimental, crossover study. Controlled laboratory. We recruited 40 athletic trainers (21 men, 19 women; age = 33.7 ± 11.2 years, height = 173.1 ± 9.2 cm, mass = 80.7 ± 17.1 kg, experience = 10.6 ± 10.4 years). Paired participants conducted 16 trials in random order for each of 4 helmet, face-mask, and shoulder-pad combinations. An 8-camera, 3-dimensional motion-capture system was used to record head motion in live models wearing properly fitted helmets and shoulder pads. Time and perceived difficulty (modified Borg CR-10). Helmet removal resulted in greater motion than face-mask removal, respectively, in the sagittal (14.88°, 95% confidence interval [CI] = 13.72°, 16.04° versus 7.04°, 95% CI = 6.20°, 7.88°; F(1,19) = 187.27, P football players must eventually be removed for imaging and medical treatment. Our results fill a gap in the evidence to support current recommendations for prehospital emergent management in patients wearing protective football equipment. Helmet face masks and shoulder pads with quick-release designs allow for clinically acceptable removal times without inducing additional motion or difficulty.

Possible impacts of forest decline on the protection functions of forests in the Bavarian Alps

Energy Technology Data Exchange (ETDEWEB)

Suda, M

1989-01-01

In context with the forest decline phenomenon the question arises on how the protection function of forests will be affected and how possible impacts can be evaluated. First, a solution model based on a feedback-circle system is presented, which allows to assess possible impacts of forest decline on massmovements. The application of this approach to the avalanche and flooding phenomena is presented and demonstrated by model calculations for different examples in the country of Traunstein/Bavaria Alps. Finally, a model is presented which gives an answer to the question, what impacts on the tourism industry are possible due to forest decline and how these influences can be evaluated.

Skeletal muscle contraction in protecting joints and bones by absorbing mechanical impacts

Science.gov (United States)

Rudenko, O. V.; Tsyuryupa, S.; Sarvazyan, A.

2016-09-01

We have previously hypothesized that the dissipation of mechanical energy of external impact is a fundamental function of skeletal muscle in addition to its primary function to convert chemical energy into mechanical energy. In this paper, a mathematical justification of this hypothesis is presented. First, a simple mechanical model, in which the muscle is considered as a simple Hookean spring, is considered. This analysis serves as an introduction to the consideration of a biomechanical model taking into account the molecular mechanism of muscle contraction, kinetics of myosin bridges, sarcomere dynamics, and tension of muscle fibers. It is shown that a muscle behaves like a nonlinear and adaptive spring tempering the force of impact and increasing the duration of the collision. The temporal profiles of muscle reaction to the impact as functions of the levels of muscle contraction, durations of the impact front, and the time constants of myosin bridges closing, are obtained. The absorption of mechanical shock energy is achieved due to the increased viscoelasticity of the contracting skeletal muscle. Controlling the contraction level allows for the optimization of the stiffness and viscosity of the muscle necessary for the protection of the joints and bones.

Large-Scale Trade in Legally Protected Marine Mollusc Shells from Java and Bali, Indonesia.

Science.gov (United States)

Nijman, Vincent; Spaan, Denise; Nekaris, K Anne-Isola

2015-01-01

Tropical marine molluscs are traded globally. Larger species with slow life histories are under threat from over-exploitation. We report on the trade in protected marine mollusc shells in and from Java and Bali, Indonesia. Since 1987 twelve species of marine molluscs are protected under Indonesian law to shield them from overexploitation. Despite this protection they are traded openly in large volumes. We collected data on species composition, origins, volumes and prices at two large open markets (2013), collected data from wholesale traders (2013), and compiled seizure data by the Indonesian authorities (2008-2013). All twelve protected species were observed in trade. Smaller species were traded for Java and Bali, but the trade involves networks stretching hundreds of kilometres throughout Indonesia. Wholesale traders offer protected marine mollusc shells for the export market by the container or by the metric ton. Data from 20 confiscated shipments show an on-going trade in these molluscs. Over 42,000 shells were seized over a 5-year period, with a retail value of USD700,000 within Indonesia; horned helmet (Cassis cornuta) (>32,000 shells valued at USD500,000), chambered nautilus (Nautilus pompilius) (>3,000 shells, USD60,000) and giant clams (Tridacna spp.) (>2,000 shells, USD45,000) were traded in largest volumes. Two-thirds of this trade was destined for international markets, including in the USA and Asia-Pacific region. We demonstrated that the trade in protected marine mollusc shells in Indonesia is not controlled nor monitored, that it involves large volumes, and that networks of shell collectors, traders, middlemen and exporters span the globe. This impedes protection of these species on the ground and calls into question the effectiveness of protected species management in Indonesia; solutions are unlikely to be found only in Indonesia and must involve the cooperation of importing countries.

Large-Scale Trade in Legally Protected Marine Mollusc Shells from Java and Bali, Indonesia

Science.gov (United States)

Nijman, Vincent; Spaan, Denise; Nekaris, K. Anne-Isola

2015-01-01

Background Tropical marine molluscs are traded globally. Larger species with slow life histories are under threat from over-exploitation. We report on the trade in protected marine mollusc shells in and from Java and Bali, Indonesia. Since 1987 twelve species of marine molluscs are protected under Indonesian law to shield them from overexploitation. Despite this protection they are traded openly in large volumes. Methodology/Principal Findings We collected data on species composition, origins, volumes and prices at two large open markets (2013), collected data from wholesale traders (2013), and compiled seizure data by the Indonesian authorities (2008–2013). All twelve protected species were observed in trade. Smaller species were traded for trade involves networks stretching hundreds of kilometres throughout Indonesia. Wholesale traders offer protected marine mollusc shells for the export market by the container or by the metric ton. Data from 20 confiscated shipments show an on-going trade in these molluscs. Over 42,000 shells were seized over a 5-year period, with a retail value of USD700,000 within Indonesia; horned helmet (Cassis cornuta) (>32,000 shells valued at USD500,000), chambered nautilus (Nautilus pompilius) (>3,000 shells, USD60,000) and giant clams (Tridacna spp.) (>2,000 shells, USD45,000) were traded in largest volumes. Two-thirds of this trade was destined for international markets, including in the USA and Asia-Pacific region. Conclusions/Significance We demonstrated that the trade in protected marine mollusc shells in Indonesia is not controlled nor monitored, that it involves large volumes, and that networks of shell collectors, traders, middlemen and exporters span the globe. This impedes protection of these species on the ground and calls into question the effectiveness of protected species management in Indonesia; solutions are unlikely to be found only in Indonesia and must involve the cooperation of importing countries. PMID:26717021

Prevention of child injuries during tornadoes: cases from the 2011 tornado outbreak in Alabama.

Science.gov (United States)

Campbell, Christine M; Baker, Mark D; Monroe, Kathy W

2012-12-01

Tornadoes and violent weather pose a hazard to children, yet little is known about the use of personal protective devices during storms. An outbreak of tornadoes on April 27, 2011, resulted in the deaths of 23 children in Alabama. Records from 60 patients seen in a pediatric emergency department for tornado-related injuries were reviewed to identify the use of injury prevention devices. Three children directly exposed to a violent tornado (Enhanced Fujita Scale 4) were using safety equipment, specifically, a helmet and infant car seats. These 3 children sustained only minor injuries. Personal protective devices may have played a role in preventing child injuries from tornadoes. To our knowledge, this is the first report in the medical literature on helmet and infant car seat use as child protective devices during tornadoes.

Indicators and protocols for monitoring impacts of formal and informal trails in protected areas

Science.gov (United States)

Marion, Jeffrey L.; Leung, Yu-Fai

2011-01-01

Trails are a common recreation infrastructure in protected areas and their conditions affect the quality of natural resources and visitor experiences. Various trail impact indicators and assessment protocols have been developed in support of monitoring programs, which are often used for management decision-making or as part of visitor capacity management frameworks. This paper reviews common indicators and assessment protocols for three types of trails, surfaced formal trails, unsurfaced formal trails, and informal (visitor-created) trails. Monitoring methods and selected data from three U.S. National Park Service units are presented to illustrate some common trail impact indicators and assessment options.

Environmental protection

International Nuclear Information System (INIS)

Klinda, J.; Lieskovska, Z.

1998-01-01

In this chapter environmental protection in the Slovak Republic in 1997 are reviewed. The economics of environmental protection, state budget, Slovak state environmental fund, economic instruments, environmental laws, environmental impact assessment, environmental management systems, and environmental education are presented

Drivers and socioeconomic impacts of tourism participation in protected areas.

Directory of Open Access Journals (Sweden)

Wei Liu

Full Text Available Nature-based tourism has the potential to enhance global biodiversity conservation by providing alternative livelihood strategies for local people, which may alleviate poverty in and around protected areas. Despite the popularity of the concept of nature-based tourism as an integrated conservation and development tool, empirical research on its actual socioeconomic benefits, on the distributional pattern of these benefits, and on its direct driving factors is lacking, because relevant long-term data are rarely available. In a multi-year study in Wolong Nature Reserve, China, we followed a representative sample of 220 local households from 1999 to 2007 to investigate the diverse benefits that these households received from recent development of nature-based tourism in the area. Within eight years, the number of households directly participating in tourism activities increased from nine to sixty. In addition, about two-thirds of the other households received indirect financial benefits from tourism. We constructed an empirical household economic model to identify the factors that led to household-level participation in tourism. The results reveal the effects of local households' livelihood assets (i.e., financial, human, natural, physical, and social capitals on the likelihood to participate directly in tourism. In general, households with greater financial (e.g., income, physical (e.g., access to key tourism sites, human (e.g., education, and social (e.g., kinship with local government officials capitals and less natural capital (e.g., cropland were more likely to participate in tourism activities. We found that residents in households participating in tourism tended to perceive more non-financial benefits in addition to more negative environmental impacts of tourism compared with households not participating in tourism. These findings suggest that socioeconomic impact analysis and change monitoring should be included in nature-based tourism

Drivers and Socioeconomic Impacts of Tourism Participation in Protected Areas

Science.gov (United States)

Liu, Wei; Vogt, Christine A.; Luo, Junyan; He, Guangming; Frank, Kenneth A.; Liu, Jianguo

2012-01-01

Nature-based tourism has the potential to enhance global biodiversity conservation by providing alternative livelihood strategies for local people, which may alleviate poverty in and around protected areas. Despite the popularity of the concept of nature-based tourism as an integrated conservation and development tool, empirical research on its actual socioeconomic benefits, on the distributional pattern of these benefits, and on its direct driving factors is lacking, because relevant long-term data are rarely available. In a multi-year study in Wolong Nature Reserve, China, we followed a representative sample of 220 local households from 1999 to 2007 to investigate the diverse benefits that these households received from recent development of nature-based tourism in the area. Within eight years, the number of households directly participating in tourism activities increased from nine to sixty. In addition, about two-thirds of the other households received indirect financial benefits from tourism. We constructed an empirical household economic model to identify the factors that led to household-level participation in tourism. The results reveal the effects of local households' livelihood assets (i.e., financial, human, natural, physical, and social capitals) on the likelihood to participate directly in tourism. In general, households with greater financial (e.g., income), physical (e.g., access to key tourism sites), human (e.g., education), and social (e.g., kinship with local government officials) capitals and less natural capital (e.g., cropland) were more likely to participate in tourism activities. We found that residents in households participating in tourism tended to perceive more non-financial benefits in addition to more negative environmental impacts of tourism compared with households not participating in tourism. These findings suggest that socioeconomic impact analysis and change monitoring should be included in nature-based tourism management systems

Drivers and socioeconomic impacts of tourism participation in protected areas.

Science.gov (United States)

Liu, Wei; Vogt, Christine A; Luo, Junyan; He, Guangming; Frank, Kenneth A; Liu, Jianguo

2012-01-01

Nature-based tourism has the potential to enhance global biodiversity conservation by providing alternative livelihood strategies for local people, which may alleviate poverty in and around protected areas. Despite the popularity of the concept of nature-based tourism as an integrated conservation and development tool, empirical research on its actual socioeconomic benefits, on the distributional pattern of these benefits, and on its direct driving factors is lacking, because relevant long-term data are rarely available. In a multi-year study in Wolong Nature Reserve, China, we followed a representative sample of 220 local households from 1999 to 2007 to investigate the diverse benefits that these households received from recent development of nature-based tourism in the area. Within eight years, the number of households directly participating in tourism activities increased from nine to sixty. In addition, about two-thirds of the other households received indirect financial benefits from tourism. We constructed an empirical household economic model to identify the factors that led to household-level participation in tourism. The results reveal the effects of local households' livelihood assets (i.e., financial, human, natural, physical, and social capitals) on the likelihood to participate directly in tourism. In general, households with greater financial (e.g., income), physical (e.g., access to key tourism sites), human (e.g., education), and social (e.g., kinship with local government officials) capitals and less natural capital (e.g., cropland) were more likely to participate in tourism activities. We found that residents in households participating in tourism tended to perceive more non-financial benefits in addition to more negative environmental impacts of tourism compared with households not participating in tourism. These findings suggest that socioeconomic impact analysis and change monitoring should be included in nature-based tourism management systems

GIS-based analysis of tourist impact in mid-mountain protected natural area, Gorce National Park, Poland

Science.gov (United States)

Tomczyk, Aleksandra

2010-05-01

Many of the middle mountain areas are especially valuable due to high bio- and geo-diversity. Therefore, this areas are often protected by law in form of National or Landscape Park, as well as Natura 2000 Network. Moreover, mountain areas usually attract significant amount of tourist. Hence, environment is subject to combination of different forces including human impact (tourism, forest management, pasture) as well as natural processes. Usually areas with low environmental resiliency are, simultaneously, very valuable from ecological point of view and attractive as tourist regions. Hiking, biking and horse riding on the tourist trails are one of the basic forms of exploration of protected areas. Apart from a tourist function, trails have a significant ecological role - they limit walking to prepared paths and prevent dispersing of visitors. Thus the terrains, which for ecological reasons have to be excluded from direct human impact, are isolated. On the other hand using of tourist trials can have negative effect on the environment. The most important manifestation of this type of impacts is destroying of plant cover by trampling and running over. It leads to expose of a bare soil and, in consequence, to initialize and accelerate of natural erosion process. Improperly using of tourist trails and forest roads may lead to develop of gullies and significant degradation of environment. Hence, reasonable management of tourist activities, forestry and pasture is necessary for sustainable development in the mid-mountain areas. Study of tourist impact together with the assessment of susceptibility of the environment to degradation can be very helpful for planning and conservation activities. Analysis of spatial data within geographic information system (GIS) supply a very useful tool for estimating, modeling and establishing the relationships between tourist impact and environmental resiliency. This study presents implementation of the GIS analysis within one of the Polish

New safety systems for better impact shock protection of pedestrians; Neue Sicherheitssysteme fuer besseren Fussgaengerschutz

Energy Technology Data Exchange (ETDEWEB)

Buechling, J.

2005-06-01

From October 2005, new vehicles in the European Union must be equipped successively with impact shock protection systems for pedestrians. There are many different concepts and solutions, from optimised front ends and flexible hoods to outside airbags, flexible shock absorbers and systems to prevent rolling over pedestrians. (orig.)

Analysis of head impacts during sub-elite hurling practice sessions.

Science.gov (United States)

O'Sullivan, D; Roe, M; Blake, C

2018-06-01

The reported incidence of head and neck injuries in hurling is 0.12 per 1000 hours, but no previous research has quantified head impact characteristics in this sport. Here, a wireless accelerometer and gyroscope captured head impacts, in 20 senior club level hurling players. Peak linear and rotational acceleration and impact location were recorded during three hurling training sessions, each player participating once. A mean of 27.9 impacts (linear acceleration >10g) per player, per session were recorded; 1314 impacts during a total exposure time of 247 minutes. Only 2.6% impacts had peak linear acceleration of >70g and 6.2% had peak rotational acceleration >7900 rad/s 2 . There were significant differences in the number and magnitude of impacts, quantified by the accelerometer, between three training sessions of differing intensity (ŋ2 0.03-0.09, p impacts during hurling, demonstrating the feasibility of this technology in the field. The sensors were able to discriminate between sessions of varying intensity. These data can be used to develop athlete monitoring protocols and may be useful in developing innovative helmet-testing standards for hurling. The potential for this technology to provide feedback has clinical utility for team medical personnel.

The influence of personal protection equipment, occupant body size, and restraint system on the frontal impact responses of Hybrid III ATDs in tactical vehicles.

Science.gov (United States)

Zaseck, Lauren Wood; Orton, Nichole Ritchie; Gruber, Rebekah; Rupp, Jonathan; Scherer, Risa; Reed, Matthew; Hu, Jingwen

2017-08-18

Although advanced restraint systems, such as seat belt pretensioners and load limiters, can provide improved occupant protection in crashes, such technologies are currently not utilized in military vehicles. The design and use of military vehicles presents unique challenges to occupant safety-including differences in compartment geometry and occupant clothing and gear-that make direct application of optimal civilian restraint systems to military vehicles inappropriate. For military vehicle environments, finite element (FE) modeling can be used to assess various configurations of restraint systems and determine the optimal configuration that minimizes injury risk to the occupant. The models must, however, be validated against physical tests before implementation. The objective of this study was therefore to provide the data necessary for FE model validation by conducting sled tests using anthropomorphic test devices (ATDs). A secondary objective of this test series was to examine the influence of occupant body size (5th percentile female, 50th percentile male, and 95th percentile male), military gear (helmet/vest/tactical assault panels), seat belt type (3-point and 5-point), and advanced seat belt technologies (pretensioner and load limiter) on occupant kinematics and injury risk in frontal crashes. In total, 20 frontal sled tests were conducted using a custom sled buck that was reconfigurable to represent both the driver and passenger compartments of a light tactical military vehicle. Tests were performed at a delta-V of 30 mph and a peak acceleration of 25 g. The sled tests used the Hybrid III 5th percentile female, 50th percentile male, and 95th percentile male ATDs outfitted with standard combat boots and advanced combat helmets. In some tests, the ATDs were outfitted with additional military gear, which included an improved outer tactical vest (IOTV), IOTV and squad automatic weapon (SAW) gunner with a tactical assault panel (TAP), or IOTV and rifleman with

Defining Indicators and Standards for Tourism Impacts in Protected Areas: Cape Range National Park, Australia

Science.gov (United States)

Moore, Susan A.; Polley, Amanda

2007-03-01

Visitors’ perceptions of impacts and acceptable standards for environmental conditions can provide essential information for the sustainable management of tourist destinations, especially protected areas. To this end, visitor surveys were administered during the peak visitor season in Cape Range National Park, on the northwest coast of Western Australia and adjacent to the iconic Ningaloo Reef. The central focus was visitors’ perceptions regarding environmental conditions and standards for potential indicators. Conditions considered of greatest importance in determining visitors’ quality of experience included litter, inadequate disposal of human waste, presence of wildlife, levels of noise, and access to beach and ocean. Standards were determined, based on visitors’ perceptions, for a range of site-specific and non-site-specific indicators, with standards for facilities (e.g., acceptable number of parking bays, signs) and for negative environmental impacts (e.g., levels of littering, erosion) sought. The proposed standards varied significantly between sites for the facilities indicators; however, there was no significant difference between sites for environmental impacts. For the facilities, the standards proposed by visitors were closely related to the existing situation, suggesting that they were satisfied with the status quo. These results are considered in the context of current research interest in the efficacy of visitor-derived standards as a basis for protected area management.

Defining indicators and standards for tourism impacts in protected areas: Cape Range National Park, Australia.

Science.gov (United States)

Moore, Susan A; Polley, Amanda

2007-03-01

Visitors' perceptions of impacts and acceptable standards for environmental conditions can provide essential information for the sustainable management of tourist destinations, especially protected areas. To this end, visitor surveys were administered during the peak visitor season in Cape Range National Park, on the northwest coast of Western Australia and adjacent to the iconic Ningaloo Reef. The central focus was visitors' perceptions regarding environmental conditions and standards for potential indicators. Conditions considered of greatest importance in determining visitors' quality of experience included litter, inadequate disposal of human waste, presence of wildlife, levels of noise, and access to beach and ocean. Standards were determined, based on visitors' perceptions, for a range of site-specific and non-site-specific indicators, with standards for facilities (e.g., acceptable number of parking bays, signs) and for negative environmental impacts (e.g., levels of littering, erosion) sought. The proposed standards varied significantly between sites for the facilities indicators; however, there was no significant difference between sites for environmental impacts. For the facilities, the standards proposed by visitors were closely related to the existing situation, suggesting that they were satisfied with the status quo. These results are considered in the context of current research interest in the efficacy of visitor-derived standards as a basis for protected area management.

Validity and sensitivity of a model for assessment of impacts of river floodplain reconstruction on protected and endangered species

International Nuclear Information System (INIS)

Nooij, R.J.W. de; Lotterman, K.M.; Sande, P.H.J. van de; Pelsma, T.; Leuven, R.S.E.W.; Lenders, H.J.R.

2006-01-01

Environmental Impact Assessment (EIA) must account for legally protected and endangered species. Uncertainties relating to the validity and sensitivity of EIA arise from predictions and valuation of effects on these species. This paper presents a validity and sensitivity analysis of a model (BIO-SAFE) for assessment of impacts of land use changes and physical reconstruction measures on legally protected and endangered river species. The assessment is based on links between species (higher plants, birds, mammals, reptiles and amphibians, butterflies and dragon- and damselflies) and ecotopes (landscape ecological units, e.g., river dune, soft wood alluvial forests), and on value assignment to protected and endangered species using different valuation criteria (i.e., EU Habitats and Birds directive, Conventions of Bern and Bonn and Red Lists). The validity of BIO-SAFE has been tested by comparing predicted effects of landscape changes on the diversity of protected and endangered species with observed changes in biodiversity in five reconstructed floodplains. The sensitivity of BIO-SAFE to value assignment has been analysed using data of a Strategic Environmental Assessment concerning the Spatial Planning Key Decision for reconstruction of the Dutch floodplains of the river Rhine, aimed at flood defence and ecological rehabilitation. The weights given to the valuation criteria for protected and endangered species were varied and the effects on ranking of alternatives were quantified. A statistically significant correlation (p < 0.01) between predicted and observed values for protected and endangered species was found. The sensitivity of the model to value assignment proved to be low. Comparison of five realistic valuation options showed that different rankings of scenarios predominantly occur when valuation criteria are left out of the assessment. Based on these results we conclude that linking species to ecotopes can be used for adequate impact assessments

Protective Skins for Composite Airliners

Science.gov (United States)

Johnson, Vicki S.; Boone, Richard L.; Jones, Shannon; Pendse, Vandana; Hayward, Greg

2014-01-01

Traditional composite aircraft structures are designed for load bearing and then overdesigned for impact damage and hot humid environments. Seeking revolutionary improvement in the performance and weight of composite structures, Cessna Aircraft Company, with sponsorship from the NASA Fundamental Aeronautics Program/Subsonic Fixed Wing Project, has developed and tested a protective skin concept which would allow the primary composite structure to carry only load and would meet the impact, hot and humid, and other requirements through protective skins. A key requirement for the protective skins is to make any impact damage requiring repair visible. Testing from the first generation of skins helped identify the most promising materials which were used in a second generation of test articles. This report summarizes lessons learned from the first generation of protective skins, the design and construction of the second-generation test articles, test results from the second generation for impact, electromagnetic effects, aesthetics and smoothing, thermal, and acoustic (for the first time), and an assessment of the feasibility of the protective skin concept.

Comparison of helmet-mounted display designs in support of wayfinding

Science.gov (United States)

Kumagai, Jason K.; Massel, Lisa; Tack, David; Bossi, Linda

2003-09-01

The Canadian Soldier Information Requirements Technology Demonstration (SIREQ TD) soldier modernization research and development program has conducted experiments to help determine the types and amount of information needed to support wayfinding across a range of terrain environments, the most effective display modality for providing the information (visual, auditory or tactile) that will minimize conflict with other infantry tasks, and to optimize interface design. In this study, seven different visual helmet-mounted display (HMD) designs were developed based on soldier feedback from previous studies. The displays and an in-service compass condition were contrasted to investigate how the visual HMD interfaces influenced navigation performance. Displays varied with respect to their information content, frame of reference, point of view, and display features. Twelve male infantry soldiers used all eight experimental conditions to locate bearings to waypoints. From a constant location, participants were required to face waypoints presented at offset bearings of 25, 65, and 120 degrees. Performance measures included time to identify waypoints, accuracy, and head misdirection errors. Subjective measures of performance included ratings of ease of use, acceptance for land navigation, and mental demand. Comments were collected to identify likes, dislikes and possible improvements required for HMDs. Results underlined the potential performance enhancement of GPS-based navigation with HMDs, the requirement for explicit directional information, the desirability of both analog and digital information, the performance benefits of an egocentric frame of reference, the merit of a forward field of view, and the desirability of a guide to help landmark. Implications for the information requirements and human factors design of HMDs for land-based navigational tasks are discussed.

CPAP by helmet for treatment of acute respiratory failure after pediatric liver transplantation.

Science.gov (United States)

Chiusolo, F; Fanelli, V; Ciofi Degli Atti, M L; Conti, G; Tortora, F; Pariante, R; Ravà, L; Grimaldi, C; de Ville de Goyet, J; Picardo, S

2018-02-01

ARF after pediatric liver transplantation accounts for high rate of morbidity and mortality associated with this procedure. The role of CPAP in postoperative period is still unknown. The aim of the study was to describe current practice and risk factors associated with the application of helmet CPAP. In this retrospective observational cohort study, 119 recipients were divided into two groups based on indication to CPAP after extubation. Perioperative variables were studied, and determinants of CPAP application were analyzed in a multivariate logistic model. Sixty patients (60/114) developed ARF and were included in the CPAP group. No differences were found between the two groups for primary disease, graft type, and blood product transfused. At multivariate analysis, weight 148 mL/kg (OR = 4.0; 95% CI = 1.6-10.1; P = .004) were the main determinants of CPAP application. In the CPAP group, five patients (8.4%) needed reintubation. Pediatric liver recipients with lower weight, higher need of inotropes/vasopressors, higher positive fluid balance after surgery, and lower PaO 2 /FiO 2 before extubation were at higher odds of developing ARF needing CPAP application. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Cross-sectional evaluation of visuomotor tracking performance following subconcussive head impacts.

Science.gov (United States)

Brokaw, E B; Fine, M S; Kindschi, K E; Santago Ii, A C; Lum, P S; Higgins, M

2018-01-01

Repeated mild traumatic brain injury (mTBI) has been associated with increased risk of degenerative neurological disorders. While the effects of mTBI and repeated injury are known, studies have only recently started examining repeated subconcussive impacts, impacts that do not result in a clinically diagnosed mTBI. In these studies, repeated subconcussive impacts have been connected to cognitive performance and brain imaging changes. Recent research suggests that performance on a visuomotor tracking (VMT) task may help improve the identification of mTBI. The goal of this study was to investigate if VMT performance is sensitive to the cumulative effect of repeated subconcussive head impacts in collegiate men's lacrosse players. A cross-sectional, prospective study was completed with eleven collegiate men's lacrosse players. Participants wore helmet-mounted sensors and completed VMT and reaction time assessments. The relationship between cumulative impact metrics and VMT metrics were investigated. In this study, VMT performance correlated with repeated subconcussive head impacts; individuals approached clinically diagnosed mTBI-like performance as the cumulative rotational velocity they experienced increased. This suggests that repeated subconcussive impacts can result in measurable impairments and indicates that visuomotor tracking performance may be a useful tool for monitoring the effects of repeated subconcussive impacts.

Protective Factors Against the Impact of School Bullying Perpetration and Victimization on Young Adult Externalizing and Internalizing Problems

OpenAIRE

Hemphill, Sheryl A.; Tollit, Michelle; Herrenkohl, Todd I.

2014-01-01

School-based bullying perpetration and victimization is common worldwide and has profound impacts on student behavior and mental health. However, few studies have examined young adult outcomes of bullying perpetration or victimization. Research on factors that protect students who have bullied or been bullied is also lacking. This study examined young adult externalizing and internalizing problems (aged 18-19 years) and adolescent protective factors related to self-reported bullying perpetrat...

The Impacts of Human Visitation on Mussel Bed Communities Along the California Coast: Are Regulatory Marine Reserves Effective in Protecting These Communities?

Science.gov (United States)

Smith, Jayson R.; Fong, Peggy; Ambrose, Richard F.

2008-04-01

Rocky intertidal habitats frequently are used by humans for recreational, educational, and subsistence-harvesting purposes, with intertidal populations damaged by visitation activities such as extraction, trampling, and handling. California Marine Managed Areas, particularly regulatory marine reserves (MRs), were established to provide legal protection and enhancement of coastal resources and include prohibitions on harvesting intertidal populations. However, the effectiveness of MRs is unclear as enforcement of no-take laws is weak and no regulations protect intertidal species from other detrimental visitor impacts such as trampling. The goal of this study was two-fold: (1) to determine impacts from human visitation on California mussel populations ( Mytilus californianus) and mussel bed community diversity; and (2) to investigate the effectiveness of regulatory MRs in reducing visitor impacts on these populations. Surveys of mussel populations and bed-associated diversity were compared: (1) at sites subjected to either high or low levels of human use, and (2) at sites either unprotected or with regulatory protection banning collecting. At sites subjected to higher levels of human visitation, mussel populations were significantly lower than low-use sites. Comparisons of mussel populations inside and outside of regulatory MRs revealed no consistent pattern suggesting that California no-take regulatory reserves may have limited effectiveness in protecting mussel communities. In areas where many people visit intertidal habitats for purposes other than collecting, many organisms will be affected by trampling, turning of rocks, and handling. In these cases, effective protection of rocky intertidal communities requires an approach that goes beyond the singular focus on collecting to reduce the full suite of impacts.

Assessment of the Effectiveness of Combat Eyewear Protection Against Blast Overpressure.

Science.gov (United States)

Sundaramurthy, A; Skotak, M; Alay, E; Unnikrishnan, G; Mao, H; Duan, X; Williams, S T; Harding, T H; Chandra, N; Reifman, J

2018-07-01

It is unclear whether combat eyewear used by U. S. Service members is protective against blast overpressures (BOPs) caused by explosive devices. Here, we investigated the mechanisms by which BOP bypasses eyewear and increases eye surface pressure. We performed experiments and developed three-dimensional (3D) finite element (FE) models of a head form (HF) equipped with an advanced combat helmet (ACH) and with no eyewear, spectacles, or goggles in a shock tube at three BOPs and five head orientations relative to the blast wave. Overall, we observed good agreement between experimental and computational results, with average discrepancies in impulse and peak-pressure values of less than 15% over 90 comparisons. In the absence of eyewear and depending on the head orientation, we identified three mechanisms that contributed to pressure loading on the eyes. Eyewear was most effective at 0 deg orientation, with pressure attenuation ranging from 50 (spectacles) to 80% (goggles) of the peak pressures observed in the no-eyewear configuration. Spectacles and goggles were considerably less effective when we rotated the HF in the counter-clockwise direction around the superior-inferior axis of the head. Surprisingly, at certain orientations, spectacles yielded higher maximum pressures (80%) and goggles yielded larger impulses (150%) than those observed without eyewear. The findings from this study will aid in the design of eyewear that provides better protection against BOP.

Numerical differential protection

CERN Document Server

Ziegler, Gerhard

2012-01-01

Differential protection is a fast and selective method of protection against short-circuits. It is applied in many variants for electrical machines, trans?formers, busbars, and electric lines.Initially this book covers the theory and fundamentals of analog and numerical differential protection. Current transformers are treated in detail including transient behaviour, impact on protection performance, and practical dimensioning. An extended chapter is dedicated to signal transmission for line protection, in particular, modern digital communication and GPS timing.The emphasis is then pla

Mentoring Interventions and the Impact of Protective Assets on the Reproductive Health of Adolescent Girls and Young Women.

Science.gov (United States)

Plourde, Kate F; Ippoliti, Nicole B; Nanda, Geeta; McCarraher, Donna R

2017-08-01

Adolescent girls and young women (AGYW) are disproportionately affected by HIV and AIDS and other negative reproductive health (RH) outcomes. Emerging evidence suggests that programs to build AGYW's assets can help reduce their vulnerability to poor RH. Mentoring interventions have demonstrated a positive impact on a variety of youth development outcomes, including the protective assets needed to circumvent poor RH outcomes. The purpose of this review was to understand the types of mentoring programs for AGYW that have demonstrated effectiveness in improving protective assets, and/or, RH knowledge, intentions, behaviors, or outcomes themselves. Interventions were identified through an electronic search of the peer-reviewed and the gray literature. Studies were excluded in stages based on reviews of titles, abstracts, and full text. A review of 491 publications yielded a total of 19 articles that were included in the final review. The majority of the publications examined the impact of the one-to-one mentoring model in the United States. However, a good proportion examined the impact of both one-on-one and group-based interventions globally. The few interventions that followed a group-based model demonstrated more promise; evaluations of this model demonstrated a positive impact on RH knowledge and behavior, academic achievement, financial behavior, and social networks, as well as reductions in the experience of violence. Group-based mentoring programs demonstrated the most promise in building AGYW's protective assets and improving their RH outcomes. The most successful interventions consisted of multiple components, including mentoring, that sought to directly improve AGYW's protective assets and met with more frequency over a longer duration. Despite the promising evidence, more research is needed to better understand the relationship between assets and RH; the characteristics of successful mentoring programs; and the influence mentoring alone has on RH outcomes

Application of the ICRP approach for radiological protection of the marine environment in generic impact assessments

Energy Technology Data Exchange (ETDEWEB)

Kliaus, Viktoryia [Republican Scientific-Practical Centre of Hygiene, Laboratory of Radiation Safety, Akademicheskaya str. 8, 220012, Minsk (Belarus); Telleria, Diego M. [IAEA-Assessment and Management of Environmental Releases Unit, Wagramer Strasse 5 - PO Box 100, A-1400, Vienna (Austria); Cabianca, Tiberio [Centre for Radiation, Chemical and Environmental Hazards, PHE, Chilton, Didcot, Oxfordshire OX11 0RQ (United Kingdom)

2014-07-01

This paper presents a way to use the ICRP approach for protection of the environment in generic assessments of the radiological impact of radioactive releases to the marine environment. Generic assessments of radiological impact to the environment are needed in certain circumstances, for example, when input data are limited or when the likely radiological consequences are expected to be not significant. Under these circumstances the effort in performing the assessment must be commensurate with the potential radiological consequences. The generic assessment described in this paper is a simple tool which provides reasonable and cautious results and is applicable to multiple exposure scenarios associated with the assessment of the radiological impact of releases to the marine the environment. This generic assessment can be also used to provide preliminary results which, when compared to radiological criteria, may determine the need of further specific assessments. The ICRP based its approach to protect the environment in the definition of a set of reference animals and plants and the use of related radiological criteria, in the form of derived consideration reference levels. The paper discusses selection and exposure conditions of the reference animals and plants, methods to estimate their doses and the use of the radiological criteria, for the purpose of a generic assessment. The IAEA is elaborating applications of these generic impact assessments presented in the paper to be included in international guidance under development. (authors)

PROTECTIVE COATINGS OF FIBER BRAGG GRATING FOR MINIMIZING OF MECHANICAL IMPACT ON ITS WAVELENGTH CHARACTERISTICS

Directory of Open Access Journals (Sweden)

A. S. Munko

2015-03-01

Full Text Available The paper deals with the scheme for the study of the Bragg wavelength shift dependence on the applied tensile force. Samples of fiber Bragg gratings with different coatings have been studied: the restored acrylate coating, the heatshrinkable fusion splice protection sleeve without metal rod, the heat-shrinkable fusion splice protection sleeve with a metal rod, the metal capillary, polyvinylchloride tube. For different coatings of diffractive structure, dependences of wavelength shift for the Bragg grating resonance have been obtained on the tensile strength applied to the ends of an optical fiber. It was determined that the studied FBG coatings give the possibility to reduce the mechanical impact on the Bragg wavelength shift for 1.1-15 times as compared to an uncoated waveguide. The most effective version of coated fiber Bragg grating is the heatshrinkable fusion splice protection sleeve with a metal rod. When the force (equal to 6 N is applied to the 100 mm optical fiber area with the inscribed diffractive structure, the Bragg wavelength shift is 7.5 nm for the unprotected sample and 0.5 nm for the one coated with the heat-shrinkable fusion splice protection sleeve.

Pediatric craniomaxillofacial injuries after road traffic crashes: characteristics of injuries and protective equipment use.

Science.gov (United States)

Yunus, Siti Salmiah Mohd; Ngeow, Wei Cheong; Ramli, Roszalina

2015-09-01

A cross-sectional study to determine the pattern of craniomaxillofacial (CMF) injuries among children involved in road traffic crashes was performed. The association of protective equipment use with the CMF injuries was evaluated. Retrospective records of children treated in the University Malaya Medical Centre, Kuala Lumpur, Malaysia, after road traffic crashes between January 1, 2008 and December 31, 2012 were reviewed, and, after that, telephone interviews were made. Seventy-one children were included in this study. Fifty-two (73.6%) were involved in a motorcycle injury and 19 (23.4%) in a car crash. Their mean age was 6.02 years; SD, 3.46 (range between 0 to 13 years old). More male children were observed (52.1%) compared with females (47.9%). Thirty-nine point four percent of the children sustained CMF injuries, 33.8% body injuries, and 23.9% had both CMF and other body parts injuries. The highest injury severity score was 26, whereas the lowest was 0. Many children did not use protective equipment during traveling, 44.2% of children among motorcycle pillion riders, and 78.9% among car passengers. The association between helmet use and CMF injuries was shown to be statistically significant (P belt. Copyright © 2015 Elsevier Inc. All rights reserved.

Information booklet on personal protective equipment: arm and hand protection

International Nuclear Information System (INIS)

1992-01-01

Fire, heat, cold, electro-magnetic and ionising radiation, electricity, chemicals, impacts, cuts, abrasion, etc. are the common hazards for arms and hands at work. The gloves chosen for protection of the arm and hand should cover those parts adequately and the material of the gloves should be capable of offering protection against the specific hazard involved. Criteria for choosing arm and hand protection equipment will be based on their shape and part of the arm and hand protected. Guide lines for choosing such personal protection equipment for nuclear facilities are given. (M.K.V.). 3 annexures, 1 appendix

Environmental Performance and Financing Decisions Impact on Sustainable Financial Development of Chinese Environmental Protection Enterprises

Directory of Open Access Journals (Sweden)

Kai Quan Zhang

2017-12-01

Full Text Available Environmental protection firms need to improve their ability to access financing while maintaining good economic performance under mounting environmental pressures. After the integration of trade-off and stakeholder theories, we have constructed a number of mathematical models to investigate the relationship among financing decisions, environmental performance (EP, and economic performance. Unbalanced panel data from environmental protection companies listed on Chinese stock exchanges from 2007 to 2016 were collected and analyzed. Our results have confirmed that debt financing has a significant impact on short- and long-term economic performance. Firms prefer long-term debt over short-term debt to improve their financial sustainability. Internal financing is positively related to performance because the cost of financing is lower. Environmental performance can cause extra financial burden in the short run, but will improve stakeholder relations and profitability in the long run. Our study suggests that environmental performance affects the relationship between financing decisions and economic performance. When EP initiatives are high, debt financing has a greater negative influence on short-term performance, and the effect on long-term performance is mitigated. High EP also reduces the impact of internal financing on performance.

Factors Controlling Vegetation Fires in Protected and Non-Protected Areas of Myanmar

Science.gov (United States)

Biswas, Sumalika; Vadrevu, Krishna Prasad; Lwin, Zin Mar; Lasko, Kristofer; Justice, Christopher O.

2015-01-01

Fire is an important disturbance agent in Myanmar impacting several ecosystems. In this study, we quantify the factors impacting vegetation fires in protected and non-protected areas of Myanmar. Satellite datasets in conjunction with biophysical and anthropogenic factors were used in a spatial framework to map the causative factors of fires. Specifically, we used the frequency ratio method to assess the contribution of each causative factor to overall fire susceptibility at a 1km scale. Results suggested the mean fire density in non-protected areas was two times higher than the protected areas. Fire-land cover partition analysis suggested dominant fire occurrences in the savannas (protected areas) and woody savannas (non-protected areas). The five major fire causative factors in protected areas in descending order include population density, land cover, tree cover percent, travel time from nearest city and temperature. In contrast, the causative factors in non-protected areas were population density, tree cover percent, travel time from nearest city, temperature and elevation. The fire susceptibility analysis showed distinct spatial patterns with central Myanmar as a hot spot of vegetation fires. Results from propensity score matching suggested that forests within protected areas have 11% less fires than non-protected areas. Overall, our results identify important causative factors of fire useful to address broad scale fire risk concerns at a landscape scale in Myanmar. PMID:25909632

Factors controlling vegetation fires in protected and non-protected areas of myanmar.

Directory of Open Access Journals (Sweden)

Sumalika Biswas

Full Text Available Fire is an important disturbance agent in Myanmar impacting several ecosystems. In this study, we quantify the factors impacting vegetation fires in protected and non-protected areas of Myanmar. Satellite datasets in conjunction with biophysical and anthropogenic factors were used in a spatial framework to map the causative factors of fires. Specifically, we used the frequency ratio method to assess the contribution of each causative factor to overall fire susceptibility at a 1km scale. Results suggested the mean fire density in non-protected areas was two times higher than the protected areas. Fire-land cover partition analysis suggested dominant fire occurrences in the savannas (protected areas and woody savannas (non-protected areas. The five major fire causative factors in protected areas in descending order include population density, land cover, tree cover percent, travel time from nearest city and temperature. In contrast, the causative factors in non-protected areas were population density, tree cover percent, travel time from nearest city, temperature and elevation. The fire susceptibility analysis showed distinct spatial patterns with central Myanmar as a hot spot of vegetation fires. Results from propensity score matching suggested that forests within protected areas have 11% less fires than non-protected areas. Overall, our results identify important causative factors of fire useful to address broad scale fire risk concerns at a landscape scale in Myanmar.

Factors controlling vegetation fires in protected and non-protected areas of myanmar.

Science.gov (United States)

Biswas, Sumalika; Vadrevu, Krishna Prasad; Lwin, Zin Mar; Lasko, Kristofer; Justice, Christopher O

2015-01-01

Fire is an important disturbance agent in Myanmar impacting several ecosystems. In this study, we quantify the factors impacting vegetation fires in protected and non-protected areas of Myanmar. Satellite datasets in conjunction with biophysical and anthropogenic factors were used in a spatial framework to map the causative factors of fires. Specifically, we used the frequency ratio method to assess the contribution of each causative factor to overall fire susceptibility at a 1km scale. Results suggested the mean fire density in non-protected areas was two times higher than the protected areas. Fire-land cover partition analysis suggested dominant fire occurrences in the savannas (protected areas) and woody savannas (non-protected areas). The five major fire causative factors in protected areas in descending order include population density, land cover, tree cover percent, travel time from nearest city and temperature. In contrast, the causative factors in non-protected areas were population density, tree cover percent, travel time from nearest city, temperature and elevation. The fire susceptibility analysis showed distinct spatial patterns with central Myanmar as a hot spot of vegetation fires. Results from propensity score matching suggested that forests within protected areas have 11% less fires than non-protected areas. Overall, our results identify important causative factors of fire useful to address broad scale fire risk concerns at a landscape scale in Myanmar.

Impact of Publicly Financed Health Insurance Schemes on Healthcare Utilization and Financial Risk Protection in India: A Systematic Review.

Science.gov (United States)

Prinja, Shankar; Chauhan, Akashdeep Singh; Karan, Anup; Kaur, Gunjeet; Kumar, Rajesh

2017-01-01

Several publicly financed health insurance schemes have been launched in India with the aim of providing universalizing health coverage (UHC). In this paper, we report the impact of publicly financed health insurance schemes on health service utilization, out-of-pocket (OOP) expenditure, financial risk protection and health status. Empirical research studies focussing on the impact or evaluation of publicly financed health insurance schemes in India were searched on PubMed, Google scholar, Ovid, Scopus, Embase and relevant websites. The studies were selected based on two stage screening PRISMA guidelines in which two researchers independently assessed the suitability and quality of the studies. The studies included in the review were divided into two groups i.e., with and without a comparison group. To assess the impact on utilization, OOP expenditure and health indicators, only the studies with a comparison group were reviewed. Out of 1265 articles screened after initial search, 43 studies were found eligible and reviewed in full text, finally yielding 14 studies which had a comparator group in their evaluation design. All the studies (n-7) focussing on utilization showed a positive effect in terms of increase in the consumption of health services with introduction of health insurance. About 70% studies (n-5) studies with a strong design and assessing financial risk protection showed no impact in reduction of OOP expenditures, while remaining 30% of evaluations (n-2), which particularly evaluated state sponsored health insurance schemes, reported a decline in OOP expenditure among the enrolled households. One study which evaluated impact on health outcome showed reduction in mortality among enrolled as compared to non-enrolled households, from conditions covered by the insurance scheme. While utilization of healthcare did improve among those enrolled in the scheme, there is no clear evidence yet to suggest that these have resulted in reduced OOP expenditures or

Science and values in radiological protection: impact on radiological protection decision making

International Nuclear Information System (INIS)

Salomaa, Sisko; Pinak, Miroslav

2008-01-01

Full text: This work summarises the main ideas and achievements of the Science and Values in Radiological Protection Workshop that was held on 15-17 January 2008 in Helsinki, Finland. In the view of developing of new radiological applications and emerging scientific phenomena it has been recognized a need to develop a shared understanding of emerging challenges for radiological protection among scientific and regulatory communities, public and other concerned stake holders. In response to this the Committee of Radiation Protection and Public Health of the OECD Nuclear Energy Agency and Radiation and Nuclear Safety Authority of Finland tried to initiate a process of longer-term reflection on scientific and societal issues that might challenge radiological protection in the coming years. Among general issues like radiological policy issues, improvement of understanding between research and policy communities, sharing views on emerging scientific issues, there were addressed several scientific issues, like non-targeted effects, individual sensitivity; and circulatory diseases. The main focus of these discussions was to elaborate potential 'what if' scenarios and propose feasible solutions at various levels. These discussions addressed effects that are not direct and evident consequence of the initial lesions produced at the cellular and DNA level like bystander responses, genomic instability, gene induction, adaptive responses and low dose. Particular interest was paid to an extrapolation of risk estimates to low doses and role of Linear Non-Threshold theory in setting regulatory principles. Individual radio-sensitivity and identification of genes that are suspected of having an influence on it were also discussed in one of the Breakout Sessions. Another Breakout Session addressed circulatory diseases. There is emerging evidence in the A-bomb survivors and in other exposed groups that ionising radiation also causes other diseases than cancer, such as circulatory

Measures of the EU Agri-Environmental Protection Scheme (GAEPS) and their impacts on the visual acceptability of Finnish agricultural landscapes.

Science.gov (United States)

Tahvanainen, Liisa; Ihalainen, Marjut; Hietala-Koivu, Reija; Kolehmainen, Osmo; Tyrväinen, Liisa; Nousiainen, Ismo; Helenius, Juha

2002-11-01

As a member of the European Union, Finland has committed itself to creating an environmental policy for agriculture. The aims of this study were to evaluate visual impacts of the General Agri-Environmental Protection Scheme (GAEPS) and Supplementary Protection Scheme (SPS) and general attitudes towards some activities in those policies and furthermore to examine the suitability of the method of Alho et al. (2001) for the scenic beauty assessment. The study areas consisted of three original, untreated, and 15 modified rural landscapes representing a variety of different activities. The scenic beauty of the landscapes was evaluated through pairwise comparisons of the responses of 68 people. Furthermore, attitudes towards environmental values, water protection, buffer strips and subsidies to agriculture were obtained. The respondents found the maintained buffer strips more pleasing than unmaintained strips and considered that the quality of watercourses was increased by buffer strips along them. A suitable width for the buffer strip along main ditches, brooks and waterways was regarded, on average, to be wider than the current recommendations. Although the opinions of farmers were basically in line with the existing recommendations, farmers' opininons on the second and third most important effects of buffer strips, an increase in weeds and a decrease in cultivated land, clearly differed from those of the other respondents. Afforestation, lack of building maintenance and abandoned fields were considered to be the most important factors impacting rural landscapes. This study indicates that the Finnish Agri-Environmental Protection Schemes have had positive impacts on the visual quality of landscapes. Attitudes towards other impacts are contradictory. This study also showed the improvement of the Alho et al. (2001) method in these kinds of studies relative to other methods of pairwise comparisons.

Analysis of costs for compliance with Federal Radiation Protection Guidance for Occupational Exposure. Volume 2: case study analysis of the impacts of proposed radiation protection guidance for workers

International Nuclear Information System (INIS)

1983-11-01

This report contains the writeups of case studies conducted in support of an effort to estimate costs and economic impacts of proposed Federal Radiation Protection Guidance for Occupational Exposures. The purpose of the case studies was to develop background information on representative organizations necessary to determine the impact of the proposed guidelines on selected industries. This information was used, together with other data, to estimate the aggregate costs of compliance with the proposed guidelines. The cost estimates are contained in a companion report

29 CFR 1915.34 - Mechanical paint removers.

Science.gov (United States)

2010-07-01

... injury by using goggles or face shields in accordance with the requirements of subpart I of this part. (2... shall be protected by hoods and air line respirators, or by air helmets of a positive pressure type in... blast by appropriate protective clothing, including gloves. (v) Since surges from drops in pressure in...

Going with the Flow of Nosebleeds

Science.gov (United States)

... wearing protective gear, such as helmets for hockey, football, and baseball and any other sport or activity ... need to see the doctor or visit the emergency department: You feel dizzy, weak, or faint (like ...

Environmental protection

International Nuclear Information System (INIS)

Martinez, A.S.

1987-01-01

The question of environment protection related to the use of nuclear energy aiming to power generation, based on the harmonic concept of economic and industrial development, preserving the environment, is discussed. A brief study of environmental impacts for some energy sources, including nuclear energy, to present the systems of a nuclear power plant which aim at environmental protection, is done. (M.C.K.) [pt

An ecotoxicological approach to evaluate the effects of tourism impacts in the Marine Protected Area of La Maddalena (Sardinia, Italy).

Science.gov (United States)

Moschino, V; Schintu, M; Marrucci, A; Marras, B; Nesto, N; Da Ros, L

2017-09-15

In the Marine Protected Area of La Maddalena Archipelago, environmental protection rules and safeguard measures for nautical activities have helped in reducing anthropogenic pressure; however, tourism related activities remain particularly significant in summer. With the aim of evaluating their impacts, the biomarker approach using transplanted Mytilus galloprovincialis as sentinel organisms coupled with POCIS deployment was applied. Mussels, translocated to four marine areas differently impacted by tourism activities, were sampled before, during and after the tourist season. Moreover, endocrine disruptors in passive samplers POCIS and the cellular toxicity of whole POCIS extracts on mussel haemocytes were evaluated to integrate ecotoxicological information. Lysosomal biomarkers, condition index and mortality rate, as well as metals in tissues suggested an alteration of the health status of mussels transplanted to the most impacted sites. The cellular toxicity of POCIS extracts was pointed out, notwithstanding the concentrations of the examined compounds were always below the detection limits. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ear Injuries (For Parents)

Science.gov (United States)

... pressure isn't equalized, the higher air pressure pushes on one side of the eardrum and causes ... protective equipment every time they practice or play sports — helmets for baseball, softball, hockey, and football; headgear ...

Preventing Children's Sports Injuries

Science.gov (United States)

... well. For example, they should wear helmets for baseball , softball, bicycle riding , and hockey . They also should wear ... padding. For racquet sports, field hockey, lacrosse, basketball , softball, and baseball, ask about any protective eyewear, like ...

Impact of payments for environmental services and protected areas on local livelihoods and forest conservation in northern Cambodia.

Science.gov (United States)

Clements, Tom; Milner-Gulland, E J

2015-02-01

The potential impacts of payments for environmental services (PES) and protected areas (PAs) on environmental outcomes and local livelihoods in developing countries are contentious and have been widely debated. The available evidence is sparse, with few rigorous evaluations of the environmental and social impacts of PAs and particularly of PES. We measured the impacts on forests and human well-being of three different PES programs instituted within two PAs in northern Cambodia, using a panel of intervention villages and matched controls. Both PES and PAs delivered additional environmental outcomes relative to the counterfactual: reducing deforestation rates significantly relative to controls. PAs increased security of access to land and forest resources for local households, benefiting forest resource users but restricting households' ability to expand and diversify their agriculture. The impacts of PES on household well-being were related to the magnitude of the payments provided. The two higher paying market-linked PES programs had significant positive impacts, whereas a lower paying program that targeted biodiversity protection had no detectable effect on livelihoods, despite its positive environmental outcomes. Households that signed up for the higher paying PES programs, however, typically needed more capital assets; hence, they were less poor and more food secure than other villagers. Therefore, whereas the impacts of PAs on household well-being were limited overall and varied between livelihood strategies, the PES programs had significant positive impacts on livelihoods for those that could afford to participate. Our results are consistent with theories that PES, when designed appropriately, can be a powerful new tool for delivering conservation goals whilst benefiting local people. © 2014 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Bicycle-Related Shoulder Injuries: Etiology and the Need for Protective Gear.

Science.gov (United States)

Goldstein, Yariv; Dolkart, Oleg; Kaufman, Ehud; Amar, Eyal; Sharfman, Zachary T; Rath, Ehud; Mozes, Gavriel; Maman, Eran

2016-01-01

The popularity of bicycle riding for recreation, exercise and transportation has grown enormously in recent years, which has led to an increased incidence of bicycle-related injuries. While these injuries involve mainly the musculoskeletal system, data on shoulder-specific injuries incurred while bike riding are lacking. Classifying these shoulder injuries may provide insight and assistance in the creation and implementation of effective protective gear and measures. To investigate the types and mechanisms of shoulder injuries among cyclists. This study retrospectively examined all cyclists who incurred shoulder injuries while riding and were admitted to the emergency department and shoulder clinic between January 2008 and November 2013. The study included 157 subjects with various bicycle-related shoulder injuries treated with either conservative or surgical measures. Eighty-four percent of injuries were caused by a direct blow to the shoulder, 7% by falling on an outstretched hand, 6% were traction injuries, and 3% were due to hyperabduction. Nine different clinical types of injury were observed; the most common injuries were clavicle fractures (32%), followed by acromioclavicular joint dislocations (22%), rotator cuff tears (22%), and humeral fractures (8%). Fifty-one percent of subjects were managed with conservative care and the remaining patients required surgical interventions. Shoulder injuries incurred while riding a bicycle span the entire spectrum of shoulder injuries and often result in debilitating conditions. Although the use of helmets is increasing, there is currently no effective protective gear or measures to prevent riders from suffering shoulder injuries.

Biomechanics of Concussion: The Importance of Neck Tension

Science.gov (United States)

Jadischke, Ronald

Linear and angular velocity and acceleration of the head are typically correlated to concussion. Despite improvements in helmet performance to reduce accelerations, a corresponding reduction in the incidence of concussion has not occurred (National Football League [NFL] 1996-present). There is compelling research that forces on and deformation to the brain stem are related to concussion. The brain stem is the center of control for respiration, blood pressure and heart rate and is the root of most cranial nerves. Injury to the brain stem is consistent with most symptoms of concussion reported in the National Football League and the National Hockey League, such as headaches, neck pain, dizziness, and blurred vision. In the Hybrid III anthropomorphic test device (ATD), the upper neck load cell is in close proximity to the human brain stem. This study found that the additional mass of a football helmet onto the Hybrid III headform increases the upper neck forces and moments in response to helmet-to-helmet impact and helmet-to-chest impacts. A new laboratory impactor device was constructed to simulate collisions using two moving Hybrid III ATDs. The impactor was used to recreate on-field collisions (n = 20) in American football while measuring head, neck and upper torso kinematics. A strong correlation between upper neck forces, upper neck power and the estimated strains and strain rates along the axis of the upper cervical spinal cord and brain stem and concussion was found. These biomechanical responses should be added to head kinematic responses for a more comprehensive evaluation of concussion.

Impact of protective factors on resilience of grandparent carers fostering orphans and non-orphans in Zimbabwe.

Science.gov (United States)

Mhaka-Mutepfa, Magen; Mpofu, Elias; Cumming, Robert

2015-04-01

This study sought to explore the impact of protective factors, health, and well-being on resilience of grandparents fostering orphans. Data were collected from grandparents (N = 327; M age = 62.4; SD = 11.2) in Zimbabwe using a survey instrument comprising the Resilience Scale and World Health Organization Quality of Life Questionnaire (WHOQOL-BREF). Data were analyzed using hierarchical regression, predicting resilience from demographics, personal and social assets, health, and well-being. Protective factors associated with resilience were personal assets (high self-esteem, problem-solving skills, and mastery) and social assets (social networks and spirituality). Grandparents with higher coping skills, younger age, and high socioeconomic status (SES) had superior personal competences for resilience than peers with lower self-rated personal attributes. Grandparents with good physical and mental health had higher resilience profiles. Positive emotions and good health experienced by resilient grandparent carers function as protective factors to reduce the magnitude of adversity to individuals and assist them to cope well with caregiving. © The Author(s) 2014.

A Novel Instrumented Human Head Surrogate for the Impact Evaluation of Helmets

Directory of Open Access Journals (Sweden)

Nicola Petrone

2018-02-01

Full Text Available A novel Human Head Surrogate was obtained from available MRI scans of a 50th percentile male human head. Addictive manufacturing was used to produce the skull, the brain and the skin. All original MRI geometries were partially smoothed and adjusted to provide the best biofidelity compatible with printing and molding technology. The skull was 3D-printed in ABS and ten pressure sensors were placed into it. The brain surrogate was cast from silicon rubber in the 3D-printed plastic molds. Nine tri-axial accelerometers (placed at the tops of the lobes, at the sides of the lobes, in the cerebellum and in the center of mass and a three-axis gyroscope (at the center of mass were inserted into the silicon brain during casting. The cranium, after assembly with brain, was filled with silicon oil mimicking the cerebral fluid. Silicon rubber was cast in additional 3D-printed molds to form the skin surrounding the cranium. The skull base was adapted to be compatible with the Hybrid-III neck and allow the exit of brain sensors cabling. Preliminary experiments were carried out proving the functionality of the surrogate. Results showed how multiple accelerometers and pressure sensors allowed a better comprehension of the head complex motion during impacts.

Assessing the impacts of distributed generation on the protection ...

African Journals Online (AJOL)

There is the refore, a need for a protection scheme to be adopted whose devices can “coordinate” as well as offer a reliable protection to the network. This paper proposes a protection scheme design using coordinated behaviours of relay - operated reclosers and sectionalizers, as well as manages the effect distributed ...

Manual work in cold environments and its impact on selection of materials for protective gloves based on workplace observations.

Science.gov (United States)

Irzmańska, Emilia; Wójcik, Paulina; Adamus-Włodarczyk, Agnieszka

2018-04-01

This article presents a workplace observations on manual work in cold environments and its impact on the selection of materials for protective gloves. The workplace observations was conducted on 107 workers in 7 companies and involved measurements of the temperature of air and objects in the workplaces; in addition the type of surface and shape of the objects was determined. Laboratory tests were also carried out on 11 materials for protective gloves to be used in cold environments. Protective characteristics, including mechanical properties (wear, cut, tear, and puncture resistance), insulation properties (thermal resistance), functional parameters, and hygienic properties (resistance to surface wetting, material stiffness) were evaluated. Appropriate levels of performance and quality, corresponding to the protective and functional properties of the materials, were determined. Based on the results of manual work and laboratory tests, directions for the selection of materials for the construction of protective gloves were formulated with a view to improving work ergonomics. Copyright © 2017 Elsevier Ltd. All rights reserved.

PROFILE: Environmental Impact Assessment Under the National Environmental Policy Act and the Protocol on Environmental Protection to the Antarctic Treaty.

Science.gov (United States)

Ensminger; McCold; Webb

1999-07-01

/ Antarctica has been set aside by the international community for protection as a natural reserve and a place for scientific research. Through the Antarctic Treaty of 1961, the signing nations agreed to cooperate in protecting the antarctic environment, in conducting scientific studies, and in abstaining from the exercise of territorial claims. The 1991 signing of the Protocol on Environmental Protection to the Antarctic Treaty (Protocol) by representatives of the 26 nations comprising the Antarctic Treaty Consultative Parties (Parties) significantly strengthened environmental protection measures for the continent. The Protocol required ratification by each of the governments individually prior to official implementation. The US government ratified the Protocol by passage of the Antarctic Science, Tourism, and Conservation Act of 1997. Japan completed the process by ratifying the Protocol on December 15, 1997. US government actions undertaken in Antarctica are subject to the requirements of both the Protocol and the US National Environmental Policy Act (NEPA). There are differences in the scope and intent of the Protocol and NEPA; however, both require environmental impact assessment (EIA) as part of the planning process for proposed actions that have the potential for environmental impacts. In this paper we describe the two instruments and highlight key similarities and differences with particular attention to EIA. Through this comparison of the EIA requirements of NEPA and the Protocol, we show how the requirements of each can be used in concert to provide enhanced environmental protection for the antarctic environment. NEPA applies only to actions of the US government; therefore, because NEPA includes certain desirable attributes that have been refined and clarified through numerous court cases, and because the Protocol is just entering implementation internationally, some recommendations are made for strengthening the procedural requirements of the Protocol

Susceptibility of modern relay protection: Will protection from cyber attacks help?

Directory of Open Access Journals (Sweden)

Gurevich Vladimir

2014-01-01

Full Text Available Modern trends in relay protection (RP based on the substitution of electromechanical protection relays (EMPR by digital protective relays (DPR have resulted in the emergence of an absolutely new problem, which was not known before. This problem is the possibility of an intentional remote destructive impact (IRDI on relay protection in order to put it out of action or make it perform functions that have nothing to do with the current operational mode of protected electric equipment. Traditional and well-known methods ensuring information safety cannot fully prevent unauthorized actions of RP. The article describes a new way for the problem solution.

Protecting the Amazon with protected areas

Science.gov (United States)

Walker, Robert; Moore, Nathan J.; Arima, Eugenio; Perz, Stephen; Simmons, Cynthia; Caldas, Marcellus; Vergara, Dante; Bohrer, Claudio

2009-01-01

This article addresses climate-tipping points in the Amazon Basin resulting from deforestation. It applies a regional climate model to assess whether the system of protected areas in Brazil is able to avoid such tipping points, with massive conversion to semiarid vegetation, particularly along the south and southeastern margins of the basin. The regional climate model produces spatially distributed annual rainfall under a variety of external forcing conditions, assuming that all land outside protected areas is deforested. It translates these results into dry season impacts on resident ecosystems and shows that Amazonian dry ecosystems in the southern and southeastern basin do not desiccate appreciably and that extensive areas experience an increase in precipitation. Nor do the moist forests dry out to an excessive amount. Evidently, Brazilian environmental policy has created a sustainable core of protected areas in the Amazon that buffers against potential climate-tipping points and protects the drier ecosystems of the basin. Thus, all efforts should be made to manage them effectively. PMID:19549819

Impact of End-of-Life manoeuvres on the collision risk in protected regions

Science.gov (United States)

Frey, Stefan; Lemmens, Stijn; Bastida Virgili, Benjamin; Flohrer, Tim; Gass, Volker

2017-09-01

The Inter-Agency Space Debris Coordination Committee (IADC) Space Debris Mitigation Guidelines, issued in 2002 and revised in 2007, address the post mission disposal of objects in orbit. After their mission, objects crossing the Low Earth Orbit (LEO) should have a remaining lifetime in orbit not exceeding 25 years. Objects near the Geostationary Orbit (GEO) region should be placed in an orbit that remains outside of the GEO protected region. In this paper, the impact of satellites and rocket bodies performing End-of-Life (EOL) orbital manoeuvres on the collision risk in the LEO and GEO protected regions is investigated. The cases of full or partial compliance with the IADC post mission disposal guideline are studied. ESA's Meteoroid and Space Debris Terrestrial Environment Reference (MASTER) model is used to compare the space debris flux rate of the object during the remaining lifetime estimated for the pre-EOL-manoeuvre and for the post-EOL-manoeuvre orbit. The study shows that, on average, the probability of collision can be significantly decreased by performing an EOL-manoeuver.

Fetal protection and potential liability: judicial application of the Pregnancy Discrimination Act and the disparate impact theory.

Science.gov (United States)

Moelis, L S

1985-01-01

"Fetal vulnerability programs," which are employer attempts to protect employees' unborn fetuses from harm caused by the mothers' exposure to hazardous material in the workplace, have been challenged as a form of employment discrimination. This Note analyzes the recent judicial application of the Pregnancy Discrimination Act (PDA) and the disparate impact theory to fetal vulnerability cases. The Note also examines the business necessity defense's accommodation of legitimate employer interests. The Note concludes that a more potent business necessity defense, a stricter standard for evaluating alternative protective measures, and a judicial interpretation of the PDA which is more consistent with congressional intent are necessary for fair and reasonable resolution of these cases.

Proposal for evaluation methodology on impact resistant performance and construction method of tornado missile protection net structure

International Nuclear Information System (INIS)

Namba, Kosuke; Shirai, Koji

2014-01-01

In nuclear power plants, the necessity of the Tornado Missile Protection Structure is becoming a technical key issue. Utilization of the net structure seems to be one of the realistic counter measures from the point of the view of the mitigation wind and seismic loads. However, the methodology for the selection of the net suitable materials, the energy absorption design method and the construction method are not sufficiently established. In this report, three materials (high-strength metal mesh, super strong polyethylene fiber net and steel grating) were selected for the candidate material and the material screening tests, the energy absorption tests by free drop test using the heavy weight and the impact tests with the small diameter missile. As a result, high-strength metal mesh was selected as a suitable material for tornado missile protection net structure. Moreover, the construction method to obtain the good energy absorption performance of the material and the practical design method to estimate the energy absorption of the high-strength metal mesh under tornado missile impact load were proposed. (author)

Joint Service Aircrew Mask (JSAM) Rotary Wing (RW): MPU-5 Noise Attenuation Performance

Science.gov (United States)

2016-06-09

Flight helmets have been required to protect the pilot from potentially hazardous noise exposure and provide effective speech communication...hearing loss and hearing related disabilities and provide effective speech communication capabilities. Chemical/biological (CB) protective equipment has...distribution unlimited. 88ABW Cleared 08/24/2016; 88ABW-2016-4122. earcups attached to the retention with Velcro for adjustability

The efficiency of state protection of participants in criminal proceedings from the impact of organized crime

Directory of Open Access Journals (Sweden)

Silchenko V.V.

2014-12-01

Full Text Available Illegal impact on victims and witnesses has acquired “epidemic” character and is the most dangerous form of counteraction to crimes investigation and solution. Based on his own experience of ensuring the safety of persons being the subject to state protection, the author proves the relevance and usefulness of such security measures when investigating the crimes committed by organized criminal groups (particularly grave and especially grave crimes. The problem of lack of confidence of participants in criminal proceedings in their own safety and their close persons’ safety is considered. Often the police officers themselves negatively affect this situation in case they don’t know how to implement the professional solutions in ensuring these persons’ security. A direct connection of public trust in the police with their ability to provide security of criminal proceedings participants is proved. The most effective security measures are: temporary placement in a safe place, personal protection (bodyguard, home and property protection. The mass media role in covering the positive results of law enforcement agencies activities on applying security measures for criminal proceedings participants and their close relatives is shown. The expediency of applying appropriate security measures for crimes committed by organized groups and criminal networks is emphasized: 1 it contributes to the realization of the criminal law objectives and principles, minimizes the possibility of avoiding criminal liability by criminals by unlawful impact on participants in criminal proceedings; 2 confidence in one’s own and close people’s safety favorably affects criminal investigations and excludes refusals to participate in criminal proceedings.

Dynamic response of aircraft impact of a reactor building with protective shell on independent foundation

International Nuclear Information System (INIS)

Constantopoulos, I.V.; Vardanega, C.; Attalla, I.

1981-01-01

Aircraft impact loading can penalize significantly the design of the equipment in a conventional containment building. An alternative scheme was developed in an attempt to reduce the aircraft impact response. A preliminary study was carried out to investigate the feasibility of the alternative scheme. This study was made in such perspective and for the purpose of comparing the response to aircraft impact of a standard reactor building, to that of a reactor building having an independently founded outer shell. In the second scheme, the outer shell is meant to receive the aircraft impact, so that the load will be transmitted to the reactor building internals only by way of the structure-soil-structure system. In both cases, the aircraft impact was postulated to occur on a linear single degree of freedom oscillator which modeled, approximately, the plastification of the impact area. The soil was considered as a half-space with properties corresponding to a medium stiff soil, and modeled by lumped soil springs and dashpots. The reactor internals, inner shell and protective outer shell were modeled with beam elements and concentrated inertias. In modeling the coupled system, soil-structure interaction and structure-to-structure interaction through the soil were represented by a global stiffness matrix corresponding to the three degrees the freedom of each foundation, i.e. horizontal, vertical and rocking. (orig./HP)

From Dalek half balls to Daft Punk helmets: Mimetic fandom and the crafting of replicas

Directory of Open Access Journals (Sweden)

Matt Hills

2014-06-01

Full Text Available Mimetic fandom is a surprisingly understudied mode of (culturally masculinized fan activity in which fans research and craft replica props. Mimetic fandom can be considered as (inauthentic and (immaterial, combining noncommercial status with grassroots marketing or brand reinforcement as well as fusing an emphasis on material artifacts with Web 2.0 collective intelligence. Simply analyzing mimetic fandom as part of fannish material culture fails to adequately assess the nonmaterial aspects of this collaborative creativity. Two fan cultures are taken as case studies: Dalek building groups and Daft Punk helmet constructors. These diverse cases indicate that mimetic fandom has a presence and significance that moves across media fandoms and is not restricted to the science fiction, fantasy, and horror followings with which it is most often associated. Mimetic fandom may be theorized as an oscillatory activity that confuses binaries and constructions of (academic/fan authenticity. This fan practice desires and pursues a kind of ontological bridging or unity—from text to reality—that is either absent or less dominant in many other fan activities such as cosplay, screen-used prop collecting, and geographical pilgrimage. Fan studies may benefit from reassessing the place of mimesis, especially in order to theorize fan practices that are less clearly transformative in character.

Nature protection and socio-economic development in selected protected landscape areas

Czech Academy of Sciences Publication Activity Database

Kušová, Drahomíra; Těšitel, Jan; Matějka, K.; Bartoš, Michael

2005-01-01

Roč. 24, č. 1 (2005), s. 109-123 ISSN 1335-342X R&D Projects: GA MŽP(CZ) SM/610/3/03 Institutional research plan: CEZ:AV0Z60870520 Keywords : protected landscape areas * nature protection * biosphere reserves * socio-economic development Subject RIV: DO - Wilderness Conservation Impact factor: 0.085, year: 2005

Managing ecotourism visitation in protected areas

Science.gov (United States)

Marion, J.L.; Farrell, T.A.; Lindberg, Kreg; Wood, Megan Epler; Engeldrum, David

1998-01-01

Ecotourism management seeks to integrate and balance several potentially conflicting objectives: protection of natural and cultural resources, provision of recreation opportunities and generation of economic benefits. In the absence of effective planning and management, ecotourism can lead to significant negative impacts on vegetation, soil, water, wildlife, historic resources, cultures, and visitor experiences. This chapter reviews visitor-related natural resource and experience impacts associated with ecotourism within protected areas. The influence of factors that control the nature and extent of impacts are also reviewed, including type and amount of use, the variable resistance and resilience of environmental attributes such as vegetation and soil types, and the role of management in shaping visitation, resources and facilities to support visitation while minimizing associated impacts. Implications for managing the effects of protected area visitation are highlighted, including carrying capacity decision frameworks and selecting management strategies and tactics.

Aging assessment for active fire protection systems