WorldWideScience

Sample records for helichrysum obconicum dc

  1. Analysis of Helichrysum oligocephalum DC. essential oil

    N. Ghassemi-Dehkordi

    2015-12-01

    Full Text Available Background and objectives: Helichrysum oligocephalum DC. (Compositae  is an endemic plant in Iran that has been recommended by Iranian traditional and folk medicine practitioners for gastrointestinal complaints. The plant is rich in essential oil and in the present investigation, the volatile composition of the species has been determined. Methods: The light yellow essential oil from the aerial parts of the plant was prepared according to the method which was recommended in British Pharmacopoeia by using hydrodistillation. The chemical composition of the oil was investigated by gas chromatography mass spectroscopy (GC/MS. Results: Thirty-seven compounds were identified; among them β-caryophyllene, α-humulene and epimanoyl oxide were dominant. Sesquiterpenoids were the most dominant compounds in the essential oil while monoterpenoides, fatty acids and diterpenoides were found to be less. These outcomes are a little bit different from what has been reported before. Conclusion: The differences between the results of the present study with previous works could be due to the diversity of variety, polymorphism, stage of plant growth and environmental factors.

  2. Antimicrobial activity of Helichrysum plicatum DC

    Bigović Dubravka J.

    2017-01-01

    Full Text Available Dry flower heads of Helichrysum plicatum were characterized by HPLC-DAD and a detailed antimicrobial assay of its ethanol extract was performed. Identification of phenolic compounds indicated the presence of apigenin, naringenin and kaempferol as free aglycones, glycosides of apigenin, naringenin, quercetin and kaempferol as well as chlorogenic acid and chalcone derivate. Antimicrobial activity of the extract was evaluated against various bacteria and fungi as well as yeast Candida albicans using microdilution method. Grampositive bacteria were more sensitive to the tested extract (MIC values were to 0.02 mg/mL than Gram-negative bacteria (the greatest MIC was 0.055 mg/mL. Regarding pathogenic fungi, our tests demonstrated that fungi were more sensitive to the tested extract than bacteria. The growth of the majority of the tested fungi was inhibited by concentration of 0.005 mg/mL. Moreover, the extract was significantly more active than commercial fungicide, fluconazole. The results of our tests indicate that the extract of H. plicatum has significant antimicrobial activity and may find application in the pharmaceutical and food industry and organic agriculture.

  3. Chemical Diversity in Volatiles of Helichrysum plicatum DC. Subspecies in Turkey

    Bintuğ Öztürk

    2014-07-01

    Full Text Available In the present work three subspecies of Helichrysum plicatum DC. (Helichrysum plicatum DC. subsp. plicatum, Helichrysum plicatum DC. subsp. polyphillum (Ledeb P.H.Davis & Kupicha and Helichrysum plicatum DC. subsp. isauricum Parolly were investigated for the essential oil chemical compositions. The volatiles were obtained by conventional hydrodistillation of aerial parts and microdistillation of inflorescences. Subsequent gas chromatography (GC-FID and gas chromatography coupled to mass spectrometry (GC/MS revealed chemical diversity in compositions of the volatiles analyzed. A total of 199 compounds were identified representing 73.9-98.3% of the volatiles compositions. High abundance of fatty acids and their esters (24.9-70.8% was detected in the herb volatiles of H. plicatum subsp. polyphyllum and H. plicatum subsp. isauricum. The inflorescences of Helichrysum subspecies were found to be rich in monoterpenes (15.0-93.1%, fatty acids (0.1-36.3% and sesquiterpenes (1.1-25.5%. The inflorescence volatiles of H. plicatum subsp. isauricum were distinguished by predomination of monoterpene hydrocarbons (93.1% with fenchene (88.3% as the major constituent

  4. Preliminary phytochemical screening and in vitro antioxidant activities of the aqueous extract of Helichrysum longifolium DC.

    Aiyegoro, Olayinka A; Okoh, Anthony I

    2010-05-14

    Many oxidative stress related diseases are as a result of accumulation of free radicals in the body. A lot of researches are going on worldwide directed towards finding natural antioxidants of plants origins. The aims of this study were to evaluate in vitro antioxidant activities and to screen for phytochemical constituents of Helichrysum longifolium DC. [Family Asteraceae] aqueous crude extract. We assessed the antioxidant potential and phytochemical constituents of crude aqueous extract of Helichrysum longifolium using tests involving inhibition of superoxide anions, DPPH, H2O2, NO and ABTS. The flavonoid, proanthocyanidin and phenolic contents of the extract were also determined using standard phytochemical reaction methods. Phytochemical analyses revealed the presence of tannins, flavonoids, steroids and saponins. The total phenolic content of the aqueous leaf extract was 0.499 mg gallic acid equivalent/g of extract powder. The total flavonoid and proanthocyanidin contents of the plant were 0.705 and 0.005 mg gallic acid equivalent/g of extract powder respectively. The percentage inhibition of lipid peroxide at the initial stage of oxidation showed antioxidant activity of 87% compared to those of BHT (84.6%) and gallic acid (96%). Also, the percentage inhibition of malondialdehyde by the extract showed percentage inhibition of 78% comparable to those of BHT (72.24%) and Gallic (94.82%). Our findings provide evidence that the crude aqueous extract of H. longifolium is a potential source of natural antioxidants, and this justified its uses in folkloric medicines.

  5. Preliminary phytochemical screening and In vitro antioxidant activities of the aqueous extract of Helichrysum longifolium DC

    Okoh Anthony I

    2010-05-01

    Full Text Available Abstract Background Many oxidative stress related diseases are as a result of accumulation of free radicals in the body. A lot of researches are going on worldwide directed towards finding natural antioxidants of plants origins. The aims of this study were to evaluate in vitro antioxidant activities and to screen for phytochemical constituents of Helichrysum longifolium DC. [Family Asteraceae] aqueous crude extract. Methods We assessed the antioxidant potential and phytochemical constituents of crude aqueous extract of Helichrysum longifolium using tests involving inhibition of superoxide anions, DPPH, H2O2, NO and ABTS. The flavonoid, proanthocyanidin and phenolic contents of the extract were also determined using standard phytochemical reaction methods. Results Phytochemical analyses revealed the presence of tannins, flavonoids, steroids and saponins. The total phenolic content of the aqueous leaf extract was 0.499 mg gallic acid equivalent/g of extract powder. The total flavonoid and proanthocyanidin contents of the plant were 0.705 and 0.005 mg gallic acid equivalent/g of extract powder respectively. The percentage inhibition of lipid peroxide at the initial stage of oxidation showed antioxidant activity of 87% compared to those of BHT (84.6% and gallic acid (96%. Also, the percentage inhibition of malondialdehyde by the extract showed percentage inhibition of 78% comparable to those of BHT (72.24% and Gallic (94.82%. Conclusions Our findings provide evidence that the crude aqueous extract of H. longifolium is a potential source of natural antioxidants, and this justified its uses in folkloric medicines.

  6. Helichrysum plicatum DC. subsp. plicatum extract as a preventive agent in experimentally induced urolithiasis model.

    Bayir, Yasin; Halici, Zekai; Keles, Mevlut Sait; Colak, Suat; Cakir, Ahmet; Kaya, Yusuf; Akçay, Fatih

    2011-11-18

    Since ancient times, various herbal preparations have been used in treatment of urolithiasis, which is basically formation of calcium oxalate stones in kidney. The aim of our study is to assess the effects of Helichrysum plicatum DC. subsp. plicatum (HP) as a preventive agent in experimentally induced urolithiasis model in rats. The efficacy of 125, 250, and 500 mg/kg HP extract was studied in 1% ethylene glycol and 1% ammonium chloride-induced urolithiasis for 21 days in rats. The weight difference and the levels of calcium, magnesium, phosphorus, urea nitrogen, creatinine and uric acid in both serum and 24h-urine were measured. The calcium oxalate (CaOx) and pH were defined in urine. Histo-pathological analyses in kidneys were also performed. The rats' weights were higher in HP groups than urolithiasis group. Urolithiasis caused a significant increase in both serum and urine biochemical parameters compared to healthy rats. HP extract decreased levels of these parameters. Urine CaOx level was high in urolithiasis rats, whereas it was decreased by HP extract. Histopathological examinations revealed extensive intratubular crystal depositions and degenerative tubular structures in urolithiasis group, but not in HP treatment groups. More studies will be necessary to elucidate the antiurolithiatic activity of HP. Nonetheless, having a beneficial effect in preventing and eliminating CaOx deposition into kidneys, HP extract may be a potential drug for urolithiasis treatment. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  7. Effect of Helichrysum plicatum DC. subsp. plicatum ethanol extract on gentamicin-induced nephrotoxicity in rats.

    Apaydin Yildirim, Betul; Kordali, Saban; Terim Kapakin, Kubra Asena; Yildirim, Fatih; Aktas Senocak, Esra; Altun, Serdar

    2017-06-01

    The aim of this study was to evaluate the possible therapeutic or protective effects of Helichrysum plicatum DC. subsp. plicatum ethanol extract (HPE) against gentamicin-induced nephrotoxicity. Thirty-six Sprague Dawley male rats weighing between 200 and 250 g were used as live material. They were formed into six groups containing 6 rats each and were allowed to adapt to laboratory conditions for 7 d. Group I: control, 5% DMSO intraperitoneal (i.p.); Group II: HPE 100 mg/(kg·d) i.p.; Group III: HPE 200 mg/(kg·d) i.p.; Group IV: gentamicin as 80 mg/(kg·d) i.p.; Group V: gentamicin as 80 mg/(kg·d) i.p.+HPE 100 mg/(kg·d) i.p.; and Group VI: gentamicin as 80 mg/(kg·d) i.p.+HPE 200 mg/(kg·d) i.p. for 8 d. Following treatment, serum, liver, and kidney tissues were used to assess blood urea nitrogen (BUN), creatinine, enzymatic and non-enzymatic antioxidants, and lipid peroxidation. Gentamicin significantly increased serum BUN, creatinin, and liver and kidney levels of malondialdehyde (MDA). It also decreased the activity of catalase (CAT), glutathione peroxidase (GPx), and superoxide dismutase (SOD). Treatment with the HPE 100 mg/kg reversed gentamicin-induced alterations as evidenced by decreased serum BUN and creatinin, liver and kidney oxidant marker, and tubular necrosis as well as by an increase in antioxidant enzymes. It was found that HPE 200 mg/kg significantly increased liver and kidney tissue MDA levels in nephrotoxicity in rats. As a result, these findings support the proposition that HPE in 100 mg/kg dose demonstrates in the kidney and liver as free radicals and scavenger to prevent the toxic effects of gentamicin in both the biochemical and histopathology parameters.

  8. Anti-inflammatory effect of Helichrysum oligocephalum DC extract on acetic acid - Induced acute colitis in rats

    Mohsen Minaiyan

    2014-01-01

    Full Text Available Background: Helichrysum oligocephalum DC. from Asteraceae family is an endemic plant growing wild in Iran. This study was carried out to investigate the effect of H. oligocephalum hydroalcoholic extract (HOHE on ulcerative colitis (UC induced by acetic acid (AA in rats. Materials and Methods: Rats were grouped (n = 6 and fasted for 24 h before colitis induction. Treatments were started 2 h before the induction of colitis and continued for two consecutive days with different doses of HOHE (100, 200, and 400 mg/kg orally (p.o. and intraperitoneally (i.p.. The colon tissue was removed and tissue damages were scored after macroscopic and histopathologic assessments. Results: Among the examined doses of HOHE, 100 mg/kg was the most effective dose that reduced the extent of UC lesions and resulted in significant alleviation. Weight/length ratio as an index of tissue inflammation and extravasation was also diminished in the treatment group administered HOHE at a dose of 100 mg/kg, and the results showed correlation with macroscopic and histopathologic evaluations. These data suggest that HOHE (100 mg/kg administered either p.o. or i.p. was effective in diminishing inflammation and ulcer indices in this murine model of acute colitis in a non-dose-related manner. Conclusions: H. oligocephalum could be considered as a suitable anticolitis alternative; however, further studies are needed to support this hypothesis for clinical setting.

  9. Anti-inflammatory effect of Helichrysum oligocephalum DC extract on acetic acid — Induced acute colitis in rats

    Minaiyan, Mohsen; Ghassemi-Dehkordi, Nasrollah; Mahzouni, Parvin; Ahmadi, Najme-Sadat

    2014-01-01

    Background: Helichrysum oligocephalum DC. from Asteraceae family is an endemic plant growing wild in Iran. This study was carried out to investigate the effect of H. oligocephalum hydroalcoholic extract (HOHE) on ulcerative colitis (UC) induced by acetic acid (AA) in rats. Materials and Methods: Rats were grouped (n = 6) and fasted for 24 h before colitis induction. Treatments were started 2 h before the induction of colitis and continued for two consecutive days with different doses of HOHE (100, 200, and 400 mg/kg) orally (p.o.) and intraperitoneally (i.p.). The colon tissue was removed and tissue damages were scored after macroscopic and histopathologic assessments. Results: Among the examined doses of HOHE, 100 mg/kg was the most effective dose that reduced the extent of UC lesions and resulted in significant alleviation. Weight/length ratio as an index of tissue inflammation and extravasation was also diminished in the treatment group administered HOHE at a dose of 100 mg/kg, and the results showed correlation with macroscopic and histopathologic evaluations. These data suggest that HOHE (100 mg/kg) administered either p.o. or i.p. was effective in diminishing inflammation and ulcer indices in this murine model of acute colitis in a non–dose-related manner. Conclusions: H. oligocephalum could be considered as a suitable anticolitis alternative; however, further studies are needed to support this hypothesis for clinical setting. PMID:24761395

  10. Biological activities and chemical composition of the stems and roots of Helichrysum oligocephalum DC grown in Iran.

    Esmaeili, Akbar

    2013-05-01

    Helichrysum has long been used medicinally, proving to be beneficial in treatment of acne, asthma, bronchitis and circulatory problems, and lymphatic system diseases. The objective of this research was to study the antioxidant and antibacterial activities and chemical composition of the compounds derived from the stems and roots of cultivated H. oligocephalum using gas chromatography (GC) and gas chromatography-mass spectroscopy (GC-MS). The primary components found in the stem oil were ortho-vanillin (51.0%) and carvacrol (16.0%), and those found in the root oil were 1,8-cineole (30.6%) and isobornyl acetate (13.9%). Stem and root oils of H. oligocephalum demonstrated antibacterial activity, particularly in relation to Gram-positive bacteria. In a β-carotene/linoleic acid bleaching assay, the root oil of H. oligocephalum demonstrated an antioxidant effect. Antioxidant capacity measured with 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay was 1205.0 for the stem oil and 722.8 μg/ml for the root oil.

  11. In Vitro Genotoxic Effects of Four Helichrysum Species in Human Lymphocytes Cultures

    Erhan H Erolu

    2010-01-01

    Full Text Available Helichrysum sanguineum, Helichrysum pamphylicum, Helichrysum orientale, Helichrysum noeanum (Asteraceae are medicinal plants. For centuries, they have been used as tea in Turkey because of their medicinal properties. So far no scientifc evidence has been found in a literature survey regarding the genotoxic effects of these plants. This work evaluated the genotoxic effects on human lymphocyte cultures induced by methanol extracts of these plants, assayed in different concentrations (0.01, 0.05, 0.1, 0.5 and 1 mg/mL. According to the results, Helichrysum noeanum, Helichrysum pamphylicum and Helichrysum sanguineum induced the formation of micronuclei and decreased the mitotic and replication indexes. Helichrysum orientale did not affect these parameters, whereas Helichrysum noeanum, Helichrysum pamphylicum and Helichrysum sanguineum were clearly genotoxic. They should therefore not be used freely in alternative medicine, although their antiproliferative activity may suggest antimitotic and anticarcinogenic properties. Helichrysum orientale could be used in alternative medicine.

  12. In vitro genotoxic effects of four Helichrysum species in human lymphocytes cultures.

    Erolu, Erhan H; Hamzaolu, Ergin; Aksoy, Ahmet; Budak, Ümit; Özkul, Yusuf

    2010-01-01

    Helichrysum sanguineum, Helichrysum pamphylicum, Helichrysum orientale, Helichrysum noeanum (Asteraceae) are medicinal plants. For centuries, they have been used as tea in Turkey because of their medicinal properties. So far no scientific evidence has been found in a literature survey regarding the genotoxic effects of these plants. This work evaluated the genotoxic effects on human lymphocyte cultures induced by methanol extracts of these plants, assayed in different concentrations (0.01, 0.05, 0.1, 0.5 and 1 mg/mL). According to the results, Helichrysum noeanum, Helichrysum pamphylicum and Helichrysum sanguineum induced the formation of micronuclei and decreased the mitotic and replication indexes. Helichrysum orientale did not affect these parameters, whereas Helichrysum noeanum, Helichrysum pamphylicum and Helichrysum sanguineum were clearly genotoxic. They should therefore not be used freely in alternative medicine, although their antiproliferative activity may suggest antimitotic and anticarcinogenic properties. Helichrysum orientale could be used in alternative medicine.

  13. Flavonoids and terpenoids from Helichrysum forskahlii.

    Al-Rehaily, Adnan J; Albishi, Omar A; El-Olemy, Mahmoud M; Mossa, Jaber S

    2008-06-01

    Three new flavonoids, namely helichrysone A (1), helichrysone B (2) and helichrysone C (3) were isolated from the aerial parts of Helichrysum forskahlii, together with 10 known flavonoids, three triterpenes, and one sesquiterpene. The structures of the new flavonoids 1-3 were established by 1D and 2D NMR spectral data. In addition, the antimicrobial activities of the isolated compounds were determined.

  14. Kaempferol, a mutagenic flavonol from Helichrysum simillimum.

    Elgorashi, Ee; van Heerden, Fr; van Staden, J

    2008-11-01

    Helichrysum simillimum is native to South Africa. It is used for the treatment of coughs, colds, fever, infections, headache, and menstrual pain. Extracts of this species showed mutagenic effects in the Salmonella/microsome assay. The aim of this study was to isolate and determine the mutagenic constituents of H. simillimum. Bioassay-guided fractionation of 90% aqueous methanol extracts, using Salmonella typhimurium TA98, led to the isolation of the flavonol kaempferol.

  15. Two new compounds from Helichrysum arenarium (L.).

    Zhang, Yu-Wei; Sun, Wu-Xing; Li, Xian; Zhao, Chun-Chao; Meng, Da-Li; Li, Ning

    2009-01-01

    Two new compounds were isolated from the whole plant of Helichrysum arenarium (L.) Moench. By means of spectroscopic data (IR, UV, 1D and 2D NMR, HR-MS, ESI-MS, and NOESY) and chemical evidence, the structures were established as 6,7-dimethoxy-4-hydroxy-1-naphthoic acid (1) and (Z)-5-hydroxy-7-methoxy-4-[3-methyl-4-(O-beta-D-xylopyranosyl)but-2-enyl]isobenzofuran-1(3H)-one (2).

  16. Helichrysum italicum: from traditional use to scientific data.

    Antunes Viegas, Daniel; Palmeira-de-Oliveira, Ana; Salgueiro, Lígia; Martinez-de-Oliveira, José; Palmeira-de-Oliveira, Rita

    2014-01-01

    Helichrysum italicum (Roth) G. Don fil. (family Asteraceae) has been used for its medicinal properties for a long time and, even nowadays, continues to play an important role in the traditional medicine of Mediterranean countries. Based on this traditional knowledge, its different pharmacological activities have been the focus of active research. This review aims to provide an overview of the current state of knowledge of the pharmacological activities of Helichrysum italicum, as well as its traditional uses, toxicity, drug interactions and safety. The selection of relevant data was made through a search using the keywords "Helichrysum italicum" and "H. italicum" in "Directory of Open Access Journals", "Google Scholar", "ISI Web of Knowledge", "PubMed", "ScienceDirect" and "Wiley Online Library". Information obtained in local and foreign books and other sources was also included. There are reports on the traditional use of Helichrysum italicum in European countries, particularly Italy, Spain, Portugal and Bosnia and Herzegovina. In these countries, its flowers and leaves are the most used parts in the treatment of health disorders such as allergies, colds, cough, skin, liver and gallbladder disorders, inflammation, infections and sleeplessness. In order to validate some of the traditional uses of Helichrysum italicum and highlight other potential applications for its extracts and isolated compounds, several scientific studies have been conducted in the last decades. In vitro studies characterized Helichrysum italicum as an antimicrobial and anti-inflammatory agent. Its flavonoids and terpenes were effective against bacteria (e.g. Staphylococcus aureus), its acetophenones, phloroglucinols and terpenoids displayed antifungal action against Candida albicans and its flavonoids and phloroglucinols inhibited HSV and HIV, respectively. Helichrysum italicum acetophenones, flavonoids and phloroglucinols demonstrated inhibitory action in different pathways of arachidonic

  17. In Vitro Genotoxic Effects of Four Helichrysum Species in Human Lymphocytes Cultures

    Erolu, Erhan H; Hamzaolu, Ergin; Aksoy, Ahmet; Budak, Ümit; Özkul, Yusuf

    2010-01-01

    Helichrysum sanguineum, Helichrysum pamphylicum, Helichrysum orientale, Helichrysum noeanum (Asteraceae) are medicinal plants. For centuries, they have been used as tea in Turkey because of their medicinal properties. So far no scientifc evidence has been found in a literature survey regarding the genotoxic effects of these plants. This work evaluated the genotoxic effects on human lymphocyte cultures induced by methanol extracts of these plants, assayed in different concentrations (0.01, 0.0...

  18. Phloroglucinol derivatives and flavones from Helichrysum paronychioides

    J. Mutanyatta-Comar

    2006-06-01

    Full Text Available Investigation of Helichrysum paronychioides afforded a total of nine compounds: 4 phloroglucinol derivatives, 2 of which are novel natural products, and 5 flavone derivatives. Structures were established by various spectroscopic techniques (NMR, MS, UV, IR, CD and by comparison with literature data for the known compounds. The four phloroglucinols, trans-(2R,3R-5,7-dihydroxy-2,3-dimethyl-4-chromanone (1, 2-butanoyl-4-prenyl-1-methoxy phloroglucinol (2, 2-(2-methylpropanoyl-4-prenylphloroglucinol (3 and 2-(2-methyl- butanoyl-4-prenylphloroglucinol (4 were screened for antioxidant activity against Cu-induced LDL oxidation. Compound 4 was found to be the most active inhibiting LDL oxidation at all concentrations (0.5-10 μM while the other three showed moderate to no activity.

  19. Antimicrobial phenolics and unusual glycerides from Helichrysum italicum subsp. microphyllum.

    Taglialatela-Scafati, Orazio; Pollastro, Federica; Chianese, Giuseppina; Minassi, Alberto; Gibbons, Simon; Arunotayanun, Warunya; Mabebie, Blessing; Ballero, Mauro; Appendino, Giovanni

    2013-03-22

    During a large-scale isolation campaign for the heterodimeric phloroglucinyl pyrone arzanol (1a) from Helichrysum italicum subsp. microphyllum, several new phenolics as well as an unusual class of lipids named santinols (5a-c, 6-8) have been characterized. Santinols are angeloylated glycerides characterized by the presence of branched acyl- or keto-acyl chains and represent a hitherto unreported class of plant lipids. The antibacterial activity of arzanol and of a selection of Helichrysum phenolics that includes coumarates, benzofurans, pyrones, and heterodimeric phloroglucinols was evaluated, showing that only the heterodimers showed potent antibacterial action against multidrug-resistant Staphylococcus aureus isolates. These observations validate the topical use of Helichrysum extracts to prevent wound infections, a practice firmly established in the traditional medicine of the Mediterranean area.

  20. In vitro biological activity and essential oil composition of four indigenous South African Helichrysum species.

    Lourens, A C U; Reddy, D; Başer, K H C; Viljoen, A M; Van Vuuren, S F

    2004-12-01

    Helichrysum species are used widely to treat various medical conditions. In this study, the anti-microbial, anti-oxidant (DPPH assay) and anti-inflammatory activity (5-lipoxygenase assay) of Helichrysum dasyanthum, Helichrysum felinum, Helichrysum excisum and Helichrysum petiolare were investigated. The essential oil compositions of these species were determined. The acetone and methanol extracts as well as the essential oils exhibited activity against Gram-positive bacteria, while both the methanol and acetone extracts of all four species were active in the anti-oxidant assay. The essential oils, on the other hand, displayed activity in the 5-lipoxygenase assay, which was used as an indication of anti-inflammatory activity. Two extracts exhibited promising activity in the anti-microbial assay, the acetone extract of Helichrysum dasyanthum with a MIC value of 15.63 microg/ml and the methanol extract of Helichrysum excisum with a MIC value of 62.5 microg/ml. The acetone extract of Helichrysum dasyanthum was the most active free radical scavenger in the DPPH assay (IC(50) of 9.53 microg/ml) while values for the anti-inflammatory activity of the essential oils ranged between 25 and 32 microg/ml. The essential oil compositions of three species (Helichrysum dasyanthum, Helichrysum excisum and Helichrysum petiolare) were dominated by the presence of monoterpenes such as alpha-pinene, 1,8-cineole and p-cymene. In the oil of Helichrysum felinum, monoterpenes were largely absent. Its profile consisted of a variety of sesquiterpenes in low concentrations with beta-caryophyllene dominating.

  1. Antioxidant properties of Helichrysum pseudoplicatum Nab

    Mohammad Ali Ebrahimzadeh

    2015-01-01

    Full Text Available The genus Helichrysum (Asteraceae is comprised of approximately 500-600 species and used for the treatment of a variety of pathological conditions in folk medicine in many countries. In this study, antioxidant activities of aerial parts of H. pseudoplicatum were investigated employing various in vitro assay systems, i.e. 2,2-diphenyl-1-picrylhydrazyl (DPPH  and nitric oxide radical scavenging, reducing power and hydrogen peroxide scavenging. IC50 for DPPH radical-scavenging activity was 438.9 ± 15.6 µg/ml. The extract exhibited good reducing power at 25 - 400 µg/ml but was not comparable with that of vitamin C. The extract showed good nitric oxide-scavenging activity. IC50 was 474.3 ± 11.8 µg/ml. It was capable of scavenging hydrogen peroxide in a concentration dependent manner. It showed good activity. Its IC50 was 159.8 ± 8.2 µg/ml. The IC50 values for ascorbic acid and BHA were 21.4 and 52.0 µg/ml, respectively. The total amount of phenolic compounds in the extract was determined as gallic acid equivalents (22.7 ± 3.1 mg/g of extract and total flavonoid contents were calculated as quercetin equivalents (9.6 ± 1.3 mg/g of extract from a calibration curve. This plant contained low amount of total flavonoids and phenolic compounds. Its moderate antioxidant activities may be attributed to its low levels of phenols and flavonoids.

  2. Anticancer properties of Thymbra capitata and Helichrysum italicum essential oils

    Juliana Poças

    2014-06-01

    It has long been recognised that some EOs have antimicrobial, antibacterial, antioxidant, antiviral, antimycotic, antiparasitic, insecticidal activities. However, studies into their anti-tumoral activities are scarce. This study, indicates that Thymbra capitata and Helichrysum italicum EOs exhibited antitumor activity against RKO and MCF7 cells, deserving further research into both the mechanism of the observed anti-tumour activity and potential cancer therapeutic applications.

  3. Antioxidant activity of methanol extract of Helichrysum foetidum Moench.

    Tirillini, Bruno; Menghini, Luigi; Leporini, Lidia; Scanu, Nadia; Marino, Stefania; Pintore, Giorgio

    2013-01-01

    Methanol extract of Helichrysum foetidum Moench (Asteraceae) was investigated for antioxidative properties. The antioxidant activities were investigated by 2,2'-azinobis-3-ethylbenzothiazoline-6-sulphonic acid (ABTS) assay, 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical-scavenging, ß-carotene/linoleic acid assay, scavenging of hydrogen peroxide (HRPO test), superoxide anion scavenging (S.A.S. test) and hypochlorous acid scavenging (taurine test). The antioxidant activity was reported as IC50 and reveals Trolox-like antioxidative effects.

  4. Successful treatment of sodium oxalate induced urolithiasis with Helichrysum flowers.

    Onaran, Metin; Orhan, Nilüfer; Farahvash, Amirali; Ekin, Hasya Nazlı; Kocabıyık, Murat; Gönül, İpek Işık; Şen, İlker; Aslan, Mustafa

    2016-06-20

    Helichrysum (Asteraceae) flowers, known as "altın otu, yayla çiçeği, kudama çiçeği" , are widely used to remove kidney stones and for their diuretic properties in Turkey. To determine the curative effect of infusions prepared from capitulums of Helichrysum graveolens (M. Bieb.) Sweet (HG) and H. stoechas ssp. barellieri (Ten.) Nyman (HS) on sodium oxalate induced kidney stones. Infusions prepared from the capitulums of HG and HS were tested for their curative effect on calcium oxalate deposition induced by sodium oxalate (70mg/kg i.p.). Following the injection of sodium oxalate for 5 days, plant extracts were administered to rats at two different doses. Potassium citrate was used as positive control. Water intake, urine volume, body, liver and kidney weights were measured; biochemical and hematological analyses were conducted on urine and blood samples. Additionally, histopathological examinations were done on kidney samples. H. stoechas extract showed prominent effect at 156mg/kg dose (stone formation score: 0.33), whereas number of kidney stones was maximum in sodium oxalate group (stone formation score: 2.33). The reduction in the uric acid and oxalate levels of urine samples and the elevation in the urine citrate levels are significant and promising in extract groups. Some hematological, biochemical and enzymatic markers are also ameliorated by the extracts. This is the first report on the curative effect of immortal flowers. Our preliminary study indicated that Helichrysum extracts may be used for treatment of urolithiasis and Helichrysum extracts are an alternative therapy to potassium citrate for patients suffering from kidney stones. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  5. Cameroonenoside A: A New Antialgal Phenolic Glycoside from Helichrysum cameroonense

    Kakam Zanetsie Antoine

    2011-01-01

    Full Text Available Helichrysum cameroonense is known for its medicinal value . This paper deals with a phytochemical investigation of this species, from which cameroonenoside A (1, a new cinnamic acid glycoside ester has been isolated. Its structure was determined by comprehensive analyses of its 1H and 13C NMR, COSY, HMQC, and HMBC spectroscopic, and HREIMS mass spectrometric data. Preliminary studies showed that cameroonenoside A (1 showed algicidal activity against Chlorella fusca

  6. Antiviral and antituberculous activity of Helichrysum melanacme constituents.

    Lall, N; Hussein, A A; Meyer, J J M

    2006-04-01

    Bioassay guided fractionation of the acetonic extract of Helichrysum melanacme using human Influenza virus type A and a drug-sensitive strain of Mycobacterium tuberculosis in vitro resulted in the isolation of 2 4',6'-trihydroxy-3'-prenylchalcone (1) and 4',6',5''-trihydroxy-6'',6''-dimethyldihydropyrano[2'',3''-2',3'] chalcone (2) as active constituents. 3-O-methylquercetin and quercetin were also isolated but were inactive against the microorganisms tested in this study.

  7. Helichrysum monizii Lowe: phenolic composition and antioxidant potential.

    Gouveia, Sandra; Castilho, Paula C

    2012-01-01

    In Madeira Archipelago there are four endemic Helichyrsum species and three of them are used in the traditional medicine. Helichrysum monizii is a rare endemism with very scarce information available concerning its uses in the local traditional medicine. The aim of this work was to study for the first time Helichrysum monizii in terms of its antioxidant capacity and the identification of the phenolic compounds to which that activity is due. Three different methods of extraction were performed and total phenolic and flavonoid contents of extracts were correlated to radical scavenging and antioxidant capacity by DPPH, ABTS, FRAP and β-carotene assays. An HPLC-DAD-ESI/MS(n) method was employed for the separation and identification of the phenolic and flavonoid components. The results revealed a high antioxidant potential mainly related to the phenolic profile of the plant. Polar components of methanol extracts of Helichrsyum monizii were detected by a high-performance liquid chromatography/electrospray ionisation tandem mass spectrometry (HPLC-DAD-ESI/MS(n) ) method. Thirty-three compounds were identified and 19 of them were identified as quinic acid derivatives. The high antioxidant potential Helichrysum monizii was for the first time established. Dicaffeoylquinic acids are the main responsible for that activity. Copyright © 2011 John Wiley & Sons, Ltd.

  8. Protease-inhibiting, molecular modeling and antimicrobial activities of extracts and constituents from Helichrysum foetidum and Helichrysum mechowianum (compositae).

    Malolo, Fanny-Aimée Essombe; Bissoue Nouga, Achille; Kakam, Antoine; Franke, Katrin; Ngah, Lidwine; Flausino, Otavio; Mpondo Mpondo, Emmanuel; Ntie-Kang, Fidele; Ndom, Jean Claude; Bolzani, Vanderlan da Silva; Wessjohann, Ludger

    2015-01-01

    Helichrysum species are used extensively for stress-related ailments and as dressings for wounds normally encountered in circumcision rites, bruises, cuts and sores. It has been reported that Helichysum species are used to relief abdominal pain, heart burn, cough, cold, wounds, female sterility, menstrual pain. From the extracts of Helichrysum foetidum (L.) Moench, six known compounds were isolated and identified. They were 7, 4'-dihydroxy-5-methoxy-flavanone (1), 6'-methoxy-2',4, 4'-trihydroxychalcone (2), 6'-methoxy-2',4-dihydroxychalcone -4'-O-β-D-glucoside (3), apigenin (4), apigenin-7-O-β-D-glucoside (5), kaur-16-en-18-oic acid (6) while two known compounds 3,5,7-trihydroxy-8-methoxyflavone (12), 4,5-dicaffeoyl quinic acid (13) together with a mixture of phytosterol were isolated from the methanol extract of Helichrysum mechowianum Klatt. All the compounds were characterized by spectroscopic and mass spectrometric methods, and by comparison with literature data. Both extracts and all the isolates were screened for the protease inhibition, antibacterial and antifungal activities. In addition, the phytochemical profiles of both species were investigated by ESI-MS experiments. These results showed that the protease inhibition assay of H. foetidum could be mainly attributed to the constituents of flavonoids glycosides (3, 5) while the compound (13) from H. mechowianum contributes to the stomach protecting effects. In addition, among the antibacterial and antifungal activities of all the isolates, compound (6) was found to possess a potent inhibitor effect against the tested microorganisms. The heterogeneity of the genus is also reflected in its phytochemical diversity. The differential bioactivities and determined constituents support the traditional use of the species. Molecular modelling was carried out by computing selected descriptors related to drug absorption, distribution, metabolism, excretion and toxicity (ADMET). Graphical abstractCompounds isolated

  9. Karyotype and genome size analyses in species of Helichrysum (Asteraceae

    Narjes Azizi

    2014-09-01

    Full Text Available Karyotype studies were performed in 18 populations of eight Helichrysum species in Iran. Those species showed chromosome numbers of 2n = 2x = 14; 2n = 4x = 24, 28 and 32; 2n = 6x = 36; 2n = 7x = 42; 2n = 8x = 48; 2n = 9x = 54; and 2n = 10x = 60. The chromosome numbers of H. davisianum, H. globiferum, H. leucocephalum and H. oocephalum are reported here for the first time. New ploidy levels are reported for H. oligocephalum (2n = 4x = 24 and H. plicatum (2n = 4x = 32. The chromosomes were metacentric and submetacentric. An ANOVA among H. globiferum and H. leucocephalum populations showed significant differences for the coefficient of variation for chromosome size, total form percentage and the asymmetry indices, indicating that changes in the chromosome structure of Helichrysum species occurred during their diversification. Significant positive correlations among the species and populations studied, in terms of the total chromosome length, lengths of the short arms and lengths of the long arms, indicate that these karyotypic features change simultaneously during speciation events. The genome sizes of Helichrysum species are reported here for first time. The 2C DNA content ranged from 8.13 pg (in H. rubicundum to 18.4 pg (in H. leucocephalum and H. davisianum. We found that C-value correlated significantly with ploidy level, total chromosome length, lengths of the long arms and lengths of the short arms (p<0.05, indicating that changes in chromosome structure are accompanied by changes in DNA content.

  10. ANTIBACTERIAL POTENTIAL OF THE CAPITULA OF EIGHT ANATOLIAN HELICHRYSUM SPECIES

    Mustafa ASLAN

    2007-08-01

    Full Text Available Abstract\tSixteen extracts prepared with petroleum ether and ethanol from the capitula obtained from eight Helichrysum species including H. armenium subsp. araxinum, H. armenium subsp. armenium, H. arenarium, H. pallasii, H. stoechas subsp. barrelieri, H. sanguineum, H. plicatum subsp. plicatum and H. graveolens (Asteraceae growing in Turkey were screened for their antibacterial activity against ten different bacteria, six of which are the Gram-positive bacteria; namely Bacillus cereus, B. megaterium, Streptococcus mutans, Micrococcus luteus, Staphylococcus aureus and Listeria monocytogenes as well as four Gram-negative bacteria; Salmonella enteritis, Shigella sonnei, Pseudomonas aeruginosa, and Escherichia coli using disk diffusion method. Ampicilline, chloramphenicol, and erythromycin were employed as the reference drugs. Among the extracts screened, the ethanol extracts of H. pallasii, H. armenium subsp. armenium, H. plicatum subsp. plicatum and H. graveolens were found to be the most active ones with the wider antibacterial spectrum. The Helichrysum species screened herein also displayed remarkable inhibitory activity against the enteric-type of bacteria, S. enteritis and S. sonnei.\tÖzet\tH. armenium subsp. araxinum, H. armenium subsp. armenium, H. arenarium, H. pallasii, H. stoechas subsp. barrelieri, H. sanguineum, H. plicatum subsp. plicatum and H. graveolens (Asteraceae olmak üzere Türkiye’de yetisen 8 Helichrysum türünden petrol eteri ve etanol ile hazirlanan onalti ekstre, 6’si Gram-pozitif (Bacillus cereus, B. megaterium, Streptococcus mutans, Micrococcus luteus, Staphylococcus aureus ve Listeria monocytogenes, 4’ü Gram-negatif (Salmonella enteritis, Shigella sonnei, Pseudomonas aeruginosa ve Escherichia coli olan 10 farkli bakteriye karsi antibakteriyel aktiviteleri açisindan disk diffüzyon yöntemi kullanilarak taranmistir. Ampisilin, kloramfenikol ve eritromisin referans ilaçlar olarak kullanilmistir. Taranan

  11. Flavonoids of Helichrysum compactum and their antioxidant and antibacterial activity.

    Süzgeç, Sevda; Meriçli, Ali H; Houghton, Peter J; Cubukçu, Bayhan

    2005-03-01

    From the capitula of Helichrysum compactum, the flavonoids apigenin, kaempferol, luteolin, naringenin, 3,5-dihydroxy-6,7,8-trimethoxyflavone, kaempferol-3-O-glucoside, luteolin-7-O-glucoside and luteolin-4',7-di-O-glucoside and from the leafy stems apigenin, kaempferol, luteolin, quercetin, apigenin-7-O-glucoside, luteolin-7-O-glucoside, and quercetin-3-O-glucoside were isolated. Extracts of the capitula of H. compactum show antioxidant activity by inhibition of lipid peroxidation and also show antibacterial activity.

  12. Flavonoids in Helichrysum pamphylicum inhibit mammalian type I DNA topoisomerase.

    Topcu, Zeki; Ozturk, Bintug; Kucukoglu, Ozlem; Kilinc, Emrah

    2008-01-01

    DNA topoisomerases are important targets for cancer chemotherapy. We investigated the effects of a methanolic extract of Helichrysum pamphylicum on mammalian DNA topoisomerase I via in vitro plasmid supercoil relaxation assays. The extracts manifested a considerable inhibition of the enzyme's activity in a dose-dependent manner. We also performed a HPLC analysis to identify the flavonoid content of the H. pamphylicum extract and tested the identified flavonoids; luteolin, luteolin-4-glucoside, naringenin, helichrysinA and isoquercitrin, on DNA topoisomerase I activity. The measurement of the total antioxidant capacity of the flavonoid standards suggested that the topoisomerase inhibition might be correlated with the antioxidant capacity of the plant.

  13. Anticarcinogenic compounds in the Uzbek medicinal plant, Helichrysum maracandicum.

    Yagura, Toru; Motomiya, Tomoko; Ito, Michiho; Honda, Gisho; Iida, Akira; Kiuchi, Fumiyuki; Tokuda, Harukuni; Nishino, Hoyoku

    2008-04-01

    An ethanol extract of Helichrysum maracandicum showed antiproliferative activity against cultured cells of SENCAR mouse in an in vitro assay, and activity-guided fractionation of the extract resulted in the isolation of isosalipurposide as an active substance. Naringenin chalcone, the aglycone of isosalipurposide, also showed strong antiproliferative activity. An in vivo assay of two-stage carcinogenesis on mouse skin revealed that epidermal application of isosalipurposide resulted in delayed formation of papillomas. Western blot analysis showed that the expression of p38 mitogen-activated protein kinase was suppressed by the administration of naringenin chalcone or isosalipurposide, which might be related to the anticarcinogenic activity.

  14. South African Helichrysum species: a review of the traditional uses, biological activity and phytochemistry.

    Lourens, A C U; Viljoen, A M; van Heerden, F R

    2008-10-28

    In South Africa, the genus Helichrysum is widely used in traditional medicine. The uses are well documented although renaming of species and the resulting confusing taxonomic nomenclature may cause uncertainty as to which specific species was referred to in some reports. The aim of this paper is to present a collated and coherent overview of the documented traditional uses of Helichrysum species and to update the botanical identity of previously studied species. Databases (Scifinder, ISI Web of Knowledge) and several books were used to collect in information on South African Helichrysum species. The traditional uses, chemistry and biological activity of Helichrysum species have been summarized. It was attempted to give clarity as to exactly which species is refer to in the ethnobotanical literature. Although a large number of ethnopharmacological uses have been documented and the chemistry of the genus has been studied extensively, only a few South African species have been investigated for their biological activity.

  15. A volatolomic approach for studying plant variability: the case of selected Helichrysum species (Asteraceae).

    Giuliani, Claudia; Lazzaro, Lorenzo; Calamassi, Roberto; Calamai, Luca; Romoli, Riccardo; Fico, Gelsomina; Foggi, Bruno; Mariotti Lippi, Marta

    2016-10-01

    The species of Helichrysum sect. Stoechadina (Asteraceae) are well-known for their secondary metabolite content and the characteristic aromatic bouquets. In the wild, populations exhibit a wide phenotypic plasticity which makes critical the circumscription of species and infraspecific ranks. Previous investigations on Helichrysum italicum complex focused on a possible phytochemical typification based on hydrodistilled essential oils. Aims of this paper are three-fold: (i) characterizing the volatile profiles of different populations, testing (ii) how these profiles vary across populations and (iii) how the phytochemical diversity may contribute in solving taxonomic problems. Nine selected Helichrysum populations, included within the H. italicum complex, Helichrysum litoreum and Helichrysum stoechas, were investigated. H. stoechas was chosen as outgroup for validating the method. After collection in the wild, plants were cultivated in standard growing conditions for over one year. Annual leafy shoots were screened in the post-blooming period for the emissions of volatile organic compounds (VOCs) by means of headspace solid phase microextraction coupled with gas-chromatography and mass spectrometry (HS-SPME-GC/MS). The VOC composition analysis revealed the production of overall 386 different compounds, with terpenes being the most represented compound class. Statistical data processing allowed the identification of the indicator compounds that differentiate the single populations, revealing the influence of the geographical provenance area in determining the volatile profiles. These results suggested the potential use of VOCs as valuable diacritical characters in discriminating the Helichrysum populations. In addition, the cross-validation analysis hinted the potentiality of this volatolomic study in the discrimination of the Helichrysum species and subspecies, highlighting a general congruence with the current taxonomic treatment of the genus. The consistency

  16. Helichrysum and grapefruit extracts inhibit carbohydrate digestion and absorption, improving postprandial glucose levels and hyperinsulinemia in rats.

    de la Garza, Ana Laura; Etxeberria, Usune; Lostao, María Pilar; San Román, Belén; Barrenetxe, Jaione; Martínez, J Alfredo; Milagro, Fermín I

    2013-12-11

    Several plant extracts rich in flavonoids have been reported to improve hyperglycemia by inhibiting digestive enzyme activities and SGLT1-mediated glucose uptake. In this study, helichrysum ( Helichrysum italicum ) and grapefruit ( Citrus × paradisi ) extracts inhibited in vitro enzyme activities. The helichrysum extract showed higher inhibitory activity of α-glucosidase (IC50 = 0.19 mg/mL) than α-amylase (IC50 = 0.83 mg/mL), whereas the grapefruit extract presented similar α-amylase and α-glucosidase inhibitory activities (IC50 = 0.42 mg/mL and IC50 = 0.41 mg/mL, respectively). Both extracts reduced maltose digestion in noneverted intestinal sacs (57% with helichrysum and 46% with grapefruit). Likewise, both extracts inhibited SGLT1-mediated methylglucoside uptake in Caco-2 cells in the presence of Na(+) (56% of inhibition with helichrysum and 54% with grapefruit). In vivo studies demonstrated that helichrysum decreased blood glucose levels after an oral maltose tolerance test (OMTT), and both extracts reduced postprandial glucose levels after the oral starch tolerance test (OSTT). Finally, both extracts improved hyperinsulinemia (31% with helichrysum and 50% with grapefruit) and HOMA index (47% with helichrysum and 54% with grapefruit) in a dietary model of insulin resistance in rats. In summary, helichrysum and grapefruit extracts improve postprandial glycemic control in rats, possibly by inhibiting α-glucosidase and α-amylase enzyme activities and decreasing SGLT1-mediated glucose uptake.

  17. THE INFLUENCE OF HELICHRYSUM ARENARIUM FLOWERS INFUSION ON MAST CELLS DEGRANULATION IN VITRO

    N. V. Karazhan

    2018-01-01

    Full Text Available Helichrysum arenarium flowers are medical plant raw materials with a high concentration of flavonoids (2.5– 5.0%. As compounds of this group of biologically active substances often possess antiallergic activity, Helichrysum arenarium flowers are a potential antiallergic medicine. The aim is to study an antiallergic activity of Helichrysum arenarium flowers infusion on the model of mast cells degranulation in vitro. Materials and methods. Helichrysum arenarium flowers infusion was made in accordance with the requirements of the State Pharmacopoeia of the Republic of Belarus. Mast cells were obtained from the abdominal cavity of inbred mice weighing 20–25 g. Experimental animals were divided into three groups of 5 individuals in each. The intact group was not subjected to any manipulation for 14 days. The test group was sensitized with the epidermal allergen from the cat’s fur. The placebo group was subjected to the same manipulations as the test group, by phosphate buffered saline pH 7.4 for sensitization instead of the allergen. Results and discussion. The addition of Helichrysum arenarium flowers infusion to the mast cells of the intact group and the placebo group did not affect the percentage of the mast cells degranulation (p>0.05, indicating that the animals of the intact group and the placebo group did not have a hypersensitivity to the components of the medicine under investigation. In the presence of Helichrysum arenarium flowers the percentage of the mast cells degranulation of the test group decreased in comparison with the percentage of the mast cells degranulation in the presence of the allergen from 23.6±2.1% to 8.1–16.2% (p<0.05. Semi-effective concentration of Helichrysum arenarium flowers infusion was 1.33±0.04 mg / ml. The stabilizing effect on the mast cells degranulation of the Helichrysum arenarium flowers infusion was statistically significantly lower than the stabilizing effect of the Bidens tripartita herb

  18. Cameroonemide A: a new ceramide from Helichrysum cameroonense.

    Antoine, Kakam Zanetsie; Hussain, Hidayat; Dongo, Etienne; Kouam, Simeon F; Schulz, Barbara; Krohn, Karsten

    2010-07-01

    From the extracts of all parts of the plant Helichrysum cameroonense, five compounds were isolated and identified. One of them, a ceramide, named cameroonemide A (1), is reported for the first time as a new natural product. Its structure was determined by comprehensive analyses of their 1D and 2D NMR and HR-EI-MS spectral data. The remaining four known compounds were identified by comparing their spectroscopic data with those reported in the literature as kaurenoic acid (2), 3-acetyloxykaurenoic acid (3), beta-sitosterol (4), and beta-sitosterol glucopyranoside (5). Preliminary studies showed that 3-acetyloxykaurenoic acid (3) inhibited the alga Chlorella fusca, while kaurenoic acid (2) showed strong antibacterial activity against Bacillus megaterium.

  19. Volatiles of Helichrysum italicum (Roth) G. Don from Croatia.

    Zeljković, Sanja Ćavar; Šolić, Marija Edita; Maksimović, Milka

    2015-01-01

    Helichrysum italicum (Roth) G. Don is a flowering plant of the family Asteraceae. It is rich in oil that is used for different medicinal purposes and in fragrance industry. Volatile profile of four populations of H. italicum, collected from natural habitat in Dalmatia (Croatia), was analysed by capillary GC-MS. Sample from BraČ Island had α-trans-bergamotene (10.2%) and β-acoradiene (10.1%) as the majors, whereas sample collected on Biokovo Mt. was rich in neryl acetate (8.1%). β-Acoradiene was also the main constituent of sample collected near Tijarica, whereas rosifoliol (8.5%) was the most abundant constituent in sample collected near Makarska. Presented results show the influence of environmental conditions on chemical differentiation of the volatiles of H. italicum from Croatia.

  20. Advanced DC/DC converters

    Luo, Fang Lin

    2003-01-01

    DC/DC conversion techniques have undergone rapid development in recent decades. With the pioneering work of these authors, DC/DC converters have now moved into their sixth generation. This book offers a concise, practical presentation of DC/DC converters, summarizing the spectrum of conversion tecnologies and presentingmany new ideas and more than 100 new topologies. Nowhere else in the literature are DC/DC converters so logically sorted and systematically introduced, and nowhere else can readers find detailed information on prototype topologies that represent a major contribution to modern power engineering. More than 320 figures, 60 tables, and 500 formulae facilitate understand and provide precise data.

  1. Macrosiphoniella remaudierei, a new species of aphid on Helichrysum in Iran (Hemiptera, Aphididae).

    Barbagallo, Sebastiano; Nieto Nafría, Juan M

    2016-01-01

    A new species of aphid, belonging to the genus Macrosiphoniella Del Guercio, 1911, is described using three samples collected in Iran on Helichrysum armenium (Asteraceae, Inuleae) by the late Prof. G. Remaudière. Both apterous and alate viviparous females of the new taxon, Macrosiphoniella remaudierei sp. n. , are described and compared to corresponding morphs of the closely allied Macrosiphoniella aetnensis and to other congeneric aphid species on Helichrysum in the Palaearctic region. Type specimens are now stored in the Muséum national d'Histoire naturelle in Paris.

  2. Macrosiphoniella remaudierei, a new species of aphid on Helichrysum in Iran (Hemiptera, Aphididae

    Sebastiano Barbagallo

    2017-01-01

    Full Text Available A new species of aphid, belonging to the genus Macrosiphoniella Del Guercio, 1911, is described using three samples collected in Iran on Helichrysum armenium (Asteraceae, Inuleae by the late Prof. G. Remaudière. Both apterous and alate viviparous females of the new taxon, M. remaudierei sp. n., are described and compared to corresponding morphs of the closely allied M. aetnensis and to other congeneric aphid species on Helichrysum in the Palaearctic region. Type specimens are now stored in the Muséum national d’Histoire naturelle in Paris.

  3. Antiradical and cytotoxic activity of different Helichrysum plicatum flower extracts.

    Bigović, Dubravka; Savikin, Katarina; Janković, Teodora; Menković, Nebojsa; Zdunić, Gordana; Stanojković, Tatjana; Djurić, Zorica

    2011-06-01

    Flowers of Helichrysum plicatum were extracted under different experimental conditions, and their antioxidant activity was determined by DPPH radical scavenging assay. Extracts obtained with higher concentration of ethyl acetate (90% or 100%) were found to contain the greatest amount of total phenolics (> 250 mg gallic acid equivalents/g of dried extract), and high correlation between total phenolic content and antiradical activity was observed (r = -0.79). Based on the total phenolic content and antiradical activity, some extracts were selected for investigation of cytotoxic activity toward PC3, HeLa and K562 human cancer cell lines in vitro. All tested extracts exhibited moderate activity against HeLa cells (41.9-42.1 microg/mL), whereas the extract obtained with 100% ethyl acetate was the most active against K562 and PC3 cell lines (25.9 and 39.2 microg/mL, respectively). Statistical analysis revealed significant correlation between total phenolic content and cytotoxic activity against PC3 and K562 cells. HPLC identification of phenolic compounds from the extracts indicated the presence of apigenin, naringenin and kaempferol as free aglycones, and glycosides of apigenin, naringenin, quercetin and kaempferol. Among aglycones, kaempferol displayed moderate cytostatic activity against all cell lines (24.8-64.7 microM).

  4. Antimicrobial acylphloroglucinols and dibenzyloxy flavonoids from flowers of Helichrysum gymnocomum.

    Drewes, Siegfried E; van Vuuren, Sandy F

    2008-05-01

    From the dichloromethane extract of the flowers of Helichrysum gymnocomum (Asteraceae) two known flavonoids, 4 and 5, and a known acylphloroglucinol, 3B, were isolated. In addition to 1 and 2, the 4',6'-dibenzyloxy-2'-hydroxy derivative of 2',4',6'-trihydroxychalcone and 5,7-dibenzyloxy derivative of pinocembrin, respectively, are reported in Nature for the first time. A compound 3A, related to 3B has the structure 2-methyl-1-[2,4,6-trihydroxy-3-(2-hydroxy-3-methyl-3-butenyl)phenyl]-1-propanone. Compounds 1, 2, 3A, 3B, 4 and 5 have MIC values below 64microg/ml against a selection of pathogens, with 3B having the highest sensitivity (6.3-45microg/ml) for eight of the ten pathogens tested, including Staphylococcus aureus (6.3microg/ml) and methicillin and gentamycin resistant strain of S. aureus (7.8microg/ml). With the exception of 2, the other compounds had notable activity (45-63microg/ml) towards Pseudomonas aeruginosa.

  5. Genetic and metabolite diversity of Sardinian populations of Helichrysum italicum.

    Melito, Sara; Sias, Angela; Petretto, Giacomo L; Chessa, Mario; Pintore, Giorgio; Porceddu, Andrea

    2013-01-01

    Helichrysum italicum (Asteraceae) is a small shrub endemic to the Mediterranean Basin, growing in fragmented and diverse habitats. The species has attracted attention due to its secondary metabolite content, but little effort has as yet been dedicated to assessing the genetic and metabolite diversity present in these populations. Here, we describe the diversity of 50 H. italicum populations collected from a range of habitats in Sardinia. H. italicum plants were AFLP fingerprinted and the composition of their leaf essential oil characterized by GC-MS. The relationships between the genetic structure of the populations, soil, habitat and climatic variables and the essential oil chemotypes present were evaluated using Bayesian clustering, contingency analyses and AMOVA. The Sardinian germplasm could be partitioned into two AFLP-based clades. Populations collected from the southwestern region constituted a homogeneous group which remained virtually intact even at high levels of K. The second, much larger clade was more diverse. A positive correlation between genetic diversity and elevation suggested the action of natural purifying selection. Four main classes of compounds were identified among the essential oils, namely monoterpenes, oxygenated monoterpenes, sesquiterpenes and oxygenated sesquiterpenes. Oxygenated monoterpene levels were significantly correlated with the AFLP-based clade structure, suggesting a correspondence between gene pool and chemical diversity. The results suggest an association between chemotype, genetic diversity and collection location which is relevant for the planning of future collections aimed at identifying valuable sources of essential oil.

  6. Genetic and metabolite diversity of Sardinian populations of Helichrysum italicum.

    Sara Melito

    Full Text Available BACKGROUND: Helichrysum italicum (Asteraceae is a small shrub endemic to the Mediterranean Basin, growing in fragmented and diverse habitats. The species has attracted attention due to its secondary metabolite content, but little effort has as yet been dedicated to assessing the genetic and metabolite diversity present in these populations. Here, we describe the diversity of 50 H. italicum populations collected from a range of habitats in Sardinia. METHODS: H. italicum plants were AFLP fingerprinted and the composition of their leaf essential oil characterized by GC-MS. The relationships between the genetic structure of the populations, soil, habitat and climatic variables and the essential oil chemotypes present were evaluated using Bayesian clustering, contingency analyses and AMOVA. KEY RESULTS: The Sardinian germplasm could be partitioned into two AFLP-based clades. Populations collected from the southwestern region constituted a homogeneous group which remained virtually intact even at high levels of K. The second, much larger clade was more diverse. A positive correlation between genetic diversity and elevation suggested the action of natural purifying selection. Four main classes of compounds were identified among the essential oils, namely monoterpenes, oxygenated monoterpenes, sesquiterpenes and oxygenated sesquiterpenes. Oxygenated monoterpene levels were significantly correlated with the AFLP-based clade structure, suggesting a correspondence between gene pool and chemical diversity. CONCLUSIONS: The results suggest an association between chemotype, genetic diversity and collection location which is relevant for the planning of future collections aimed at identifying valuable sources of essential oil.

  7. Medicinal flowers. XXX. Eight new glycosides, everlastosides F-M, from the flowers of Helichrysum arenarium.

    Morikawa, Toshio; Wang, Li-Bo; Ninomiya, Kiyofumi; Nakamura, Seikou; Matsuda, Hisashi; Muraoka, Osamu; Wu, Li-Jun; Yoshikawa, Masayuki

    2009-08-01

    Eight new glycosides, everlastosides F (1), G (2), H (3), I (4), J (5), K (6), L (7), and M (8), were isolated from the methanolic extract of the flowers of Helichrysum arenarium. Their structures were elucidated on the basis of chemical and physicochemical evidence.

  8. Helichrysum yurterianum (Asteraceae, Inuleae), a new species from NE Anatolia, Turkey

    Gemici, Yusuf; Tan, Kit; Yildirim, Hasan

    2008-01-01

    Helichrysum yurterianum Y. Gemici, Kit Tan, H. Yildirim & M. Gemici (Asteraceae, Inuleae) is described and illustrated. It is a serpentine endemic restricted to the province of Erzincan in NE Anatolia, Turkey. Its affinities are with H. arenarium and H. noeanum, which both have a wider distribution...

  9. ELABORATION OF APPROACHES TO THE STANDARTIZ OFATION HELICHRYSUM ARENARIUM (1. MOENCH IN PLANT MIXTURES

    A. B. Goudzenko

    2014-01-01

    Full Text Available Marker for qualitative and quantitative standardization of Helichrysum arenarium (L. Moench. flowers in the plant mixtures was determine. As a marker of Helichrysum arenarium Moench. flowers can be used flavonoid apigenin. HPLC method of determination flavonoid apigenin in raw materials and plant mixtures of flowers Helichrysum arenarium (L. Moench was developed. Contents of apigenin in the raw plant flowers were in the range from 0,1453 ± 0,0068% to 0,1657 ± 0,0085%, in terms of the dried materials. It is shown, that the presence and content of apigenin flowers Helichrysum arenarium (L. Moench can be standardized in the mixtures with the following plant:flowers, leaves and fruits of genus Crataegus L., roots of Althaea officinalis L., roots of Glycyrrhiza glabra L., roots of Cichorium intybus L., roots of Taraxacum officinale Web., cones of Humulus lupulus L., herb of Leonurus cardiaca L., herb of Hypericum perforatum L. and seeds of Linum usitatissimum L.

  10. Pollen morphology and its relationship to the taxonomy of the some taxa of helichrysum gaertner (asteraceae) in turkey

    Elkiran, O.; Bagci, E.

    2017-01-01

    Palynological studies of Helichrysum chionophilum, Helichrysum noeanum, Helichrysum arenarium subsp. aucheri, Helichrysum graveolens, H. plicatum subsp. plicatum and H. plicatum subsp. polyphyllum (Asteraceae) from Turkey have been carried out. H. chionophilum, H. noeanum and H. arenarium subsp. aucheri are endemics to Turkey. Pollen features of both taxa were observed with the Light and Scanning Electron Microscopy (SEM). The pollen type of both taxa were determined as tricolporate, pollen shapes were spheroidal and oblate-spheroidal, reticular pollen ornamentation was observed. The studies show that the pollen of the six taxa are very similar regarding pollen shapes, apertures, and ornamentation, but may be distinguished by colpus length (Clg), pore width (Plt) and pore length (Plg). The findings obtained from the study are discussed with each other and the genus patterns. (author)

  11. Contribution to a Taxonomic Revision of the Sicilian Helichrysum Taxa by PCA Analysis of Their Essential-Oil Compositions.

    Maggio, Antonella; Bruno, Maurizio; Guarino, Riccardo; Senatore, Felice; Ilardi, Vincenzo

    2016-02-01

    The chemical profile of the essential oils in ten populations of the genus Helichrysum Mill. (Asteraceae), collected in the loci classici of the nomenclatural types of the taxa endemic to Sicily, were analyzed. Our results confirm that the analysis of secondary metabolites can be used to fingerprint wild populations of Helichrysum, the chemical profiles being coherent with the systematic arrangement of the investigated populations in three main clusters, referring to the aggregates of H. stoechas, H. rupestre, and H. italicum, all belonging to the section Stoechadina. The correct nomenclatural designation of the investigated populations is discussed and the following two new combinations are proposed: Helichrysum preslianum subsp. compactum (Guss.) Maggio, Bruno, Guarino, Senatore & Ilardi and Helichrysum panormitanum subsp. latifolium Maggio, Bruno, Guarino, Senatore & Ilardi. Copyright © 2016 Verlag Helvetica Chimica Acta AG, Zürich.

  12. Milliwatt dc/dc Inverter

    Mclyman, C. W.

    1983-01-01

    Compact dc/dc inverter uses single integrated-circuit package containing six inverter gates that generate and amplify 100-kHz square-wave switching signal. Square-wave switching inverts 10-volt local power to isolated voltage at another desired level. Relatively high operating frequency reduces size of filter capacitors required, resulting in small package unit.

  13. Microsatellite primers for a species of South African everlasting daisy (Helichrysum odoratissimum; Gnaphalieae, Asteraceae).

    Glennon, Kelsey L; Cron, Glynis V

    2016-05-01

    Microsatellites were developed for the widespread Helichrysum odoratissimum (Asteraceae) to estimate gene flow across diploid populations and to test if gene flow occurs among other closely related lineages within this genus. Ten primer pairs were developed and tested using populations across South Africa; however, only seven primer pairs were polymorphic for the target species. The seven polymorphic primers amplified di- and trinucleotide repeats with up to 16 alleles per locus among 125 diploid individuals used for analyses. These markers can be used to estimate gene flow among populations of known ploidy level of H. odoratissimum to test evolutionary hypotheses. Furthermore, these markers amplify successfully in other Helichrysum species, including the other three taxonomic Group 4 species, and therefore can be used to inform taxonomic work on these species.

  14. Microsatellite primers for a species of South African everlasting daisy (Helichrysum odoratissimum; Gnaphalieae, Asteraceae)1

    Glennon, Kelsey L.; Cron, Glynis V.

    2016-01-01

    Premise of the study: Microsatellites were developed for the widespread Helichrysum odoratissimum (Asteraceae) to estimate gene flow across diploid populations and to test if gene flow occurs among other closely related lineages within this genus. Methods and Results: Ten primer pairs were developed and tested using populations across South Africa; however, only seven primer pairs were polymorphic for the target species. The seven polymorphic primers amplified di- and trinucleotide repeats with up to 16 alleles per locus among 125 diploid individuals used for analyses. Conclusions: These markers can be used to estimate gene flow among populations of known ploidy level of H. odoratissimum to test evolutionary hypotheses. Furthermore, these markers amplify successfully in other Helichrysum species, including the other three taxonomic Group 4 species, and therefore can be used to inform taxonomic work on these species. PMID:27213125

  15. Relaxant effect of the ethanol extract of Helichrysum plicatum (Asteraceae) on isolated rat ileum contractions.

    Bigovic, Dubravka; Brankovic, Suzana; Kitic, Dusanka; Radenkovic, Mirjana; Jankovic, Teodora; Savikin, Katarina; Zivanovic, Slavoljub

    2010-05-10

    Helichrysum plicatum (Turkish Helichrysum) has been used in folk medicine for the treatment of gastric and hepatic disorders. The aim of the present study was to examine the relaxant activity of an extract of H. plicatum flowers on isolated rat ileum. Segments of ileum of rats were suspended in an organ bath. Cumulative concentrations of H. plicatum ethanol extract induced a relaxant effect on spontaneous rat ileum contractions. H. plicatum extract caused a mean contractile response of 81.68 +/- 6.17% (at a dose of 0.01 mg/mL) and 30.08 +/- 9.07% (at a dose of 1 mg/mL). A similar effect was observed with papaverine (0.01-3 microg/mL). H. plicatum extract (0.01-1 mg/mL) relaxed high K+ (80 mM) precontractions, an effect similar to that caused by papaverine (0.01-3 microg/mL). The plant extract (0.03-0.3 mg/mL) also induced a significant depression of the cumulative concentration response curve for acetylcholine (5-1500 nM) (p Helichrysum plicatum flowers on the isolated rat intestine Extract of H. plicatum can inhibit the spontaneous ileum contractions and contractions induced by acetylcholine, histamine, barium and potassium ions.

  16. Helichrysum and Grapefruit Extracts Boost Weight Loss in Overweight Rats Reducing Inflammation.

    de la Garza, Ana Laura; Etxeberria, Usune; Haslberger, Alexander; Aumueller, Eva; Martínez, J Alfredo; Milagro, Fermín I

    2015-08-01

    Obesity is characterized by an increased production of inflammatory markers. High levels of circulating free fatty acids and chronic inflammation lead to increased oxidative stress, contributing to the development of insulin resistance (IR). Recent studies have focused on the potential use of flavonoids for obesity management due to their antioxidant and anti-inflammatory properties. This study was designed to investigate the antioxidant and anti-inflammatory effects of helichrysum and grapefruit extracts in overweight insulin-resistant rats. Thirty-eight male Wistar rats were randomly distributed in two groups: control group (n=8) and high-fat sucrose (HFS) group (n=30). After 22 days of ad libitum water and food access, the rats fed HFS diet changed to standard diet and were reassigned into three groups (n=10 each group): nonsupplemented, helichrysum extract (2 g/kg bw), and grapefruit extract (1 g/kg bw) administered for 5 weeks. Rats supplemented with both extracts gained less body weight during the 5-week period of treatment, showed lower serum insulin levels and liver TBARS levels. Leptin/adiponectin ratio, as an indicator of IR, was lower in both extract-administered groups. These results were accompanied by a reduction in TNFα gene expression in epididymal adipose tissue and intestinal mucosa, and TLR2 expression in intestinal mucosa. Helichrysum and grapefruit extracts might be used as complement hypocaloric diets in weight loss treatment. Both extracts helped to reduce weight gain, hyperinsulinemia, and IR, improved inflammation markers, and decreased the HFS diet-induced oxidative stress in insulin-resistant rats.

  17. In vitro antitumor actions of extracts from endemic plant Helichrysum zivojinii

    Matić Ivana Z

    2013-02-01

    Full Text Available Abstract Background The aim of this research was to determine the intensity and mechanisms of the cytotoxic actions of five extracts isolated from the endemic plant species Helichrysum zivojinii Černjavski & Soška (family Asteraceae against specific cancer cell lines. In order to evaluate the sensitivity of normal immunocompetent cells implicated in the antitumor immune response, the cytotoxicity of extracts was also tested against healthy peripheral blood mononuclear cells (PBMC. Methods The aerial parts of the plants were air-dried, powdered, and successively extracted with solvents of increasing polarity to obtain hexane, dichloromethane, ethyl-acetate, n-butanol and methanol extracts. The cytotoxic activities of the extracts against human cervix adenocarcinoma HeLa, human melanoma Fem-x, human myelogenous leukemia K562, human breast adenocarcinoma MDA-MB-361 cells and PBMC were evaluated by the MTT test. The mode of HeLa cell death was investigated by morphological analysis. Changes in the cell cycle of HeLa cells treated with the extracts were analyzed by flow cytometry. The apoptotic mechanisms induced by the tested extracts were determined using specific caspase inhibitors. Results The investigated Helichrysum zivojinii extracts exerted selective dose-dependent cytotoxic actions against selected cancer cell lines and healthy immunocompetent PBMC stimulated to proliferate, while the cytotoxic actions exerted on unstimulated PBMC were less pronounced. The tested extracts exhibited considerably stronger cytotoxic activities towards HeLa, Fem-x and K562 cells in comparison to resting and stimulated PBMC. It is worth noting that the cytotoxicity of the extracts was weaker against unstimulated PBMC in comparison to stimulated PBMC. Furthermore, each of the five extracts induced apoptosis in HeLa cells, through the activation of both intrinsic and extrinsic signaling pathways. Conclusion Extracts obtained from the endemic plant Helichrysum

  18. In vitro antitumor actions of extracts from endemic plant Helichrysum zivojinii.

    Matić, Ivana Z; Aljančić, Ivana; Žižak, Željko; Vajs, Vlatka; Jadranin, Milka; Milosavljević, Slobodan; Juranić, Zorica D

    2013-02-18

    The aim of this research was to determine the intensity and mechanisms of the cytotoxic actions of five extracts isolated from the endemic plant species Helichrysum zivojinii Černjavski & Soška (family Asteraceae) against specific cancer cell lines. In order to evaluate the sensitivity of normal immunocompetent cells implicated in the antitumor immune response, the cytotoxicity of extracts was also tested against healthy peripheral blood mononuclear cells (PBMC). The aerial parts of the plants were air-dried, powdered, and successively extracted with solvents of increasing polarity to obtain hexane, dichloromethane, ethyl-acetate, n-butanol and methanol extracts. The cytotoxic activities of the extracts against human cervix adenocarcinoma HeLa, human melanoma Fem-x, human myelogenous leukemia K562, human breast adenocarcinoma MDA-MB-361 cells and PBMC were evaluated by the MTT test. The mode of HeLa cell death was investigated by morphological analysis. Changes in the cell cycle of HeLa cells treated with the extracts were analyzed by flow cytometry. The apoptotic mechanisms induced by the tested extracts were determined using specific caspase inhibitors. The investigated Helichrysum zivojinii extracts exerted selective dose-dependent cytotoxic actions against selected cancer cell lines and healthy immunocompetent PBMC stimulated to proliferate, while the cytotoxic actions exerted on unstimulated PBMC were less pronounced. The tested extracts exhibited considerably stronger cytotoxic activities towards HeLa, Fem-x and K562 cells in comparison to resting and stimulated PBMC. It is worth noting that the cytotoxicity of the extracts was weaker against unstimulated PBMC in comparison to stimulated PBMC. Furthermore, each of the five extracts induced apoptosis in HeLa cells, through the activation of both intrinsic and extrinsic signaling pathways. Extracts obtained from the endemic plant Helichrysum zivojinii may represent an important source of novel potential

  19. Antiinflammatory and antioxidant flavonoids from Helichrysum kraussii and H. odoratissimum flowers.

    Legoalea, Percival B; Mashimbyeb, Mahlori J; van Rec, Teunis

    2013-10-01

    Organic extracts of the flowers of Helichrysum kraussii and H. odoratissimum contain several bioactive flavonoids, characterized by 'H NMR, '3C NMR and mass spectrometry. Four flavonoids, 5,6-dihydroxy-3,7,8-trimethoxyflavone, 5,7-dihydroxy-3-methoxyflavone, 3',4',5,7-tetrahydroxy-3-methoxyflavone and 3',4',3,5-tetrahydroxy-7-methoxyflavone, have antioxidant activity by the DPPH free radical assay, while 5,6-dihydroxy-3,7,8-trimethoxyflavone and 3',4',3,5-tetrahydroxy-7-methoxyflavone have promising anti-inflammatory activity.

  20. Phytochemical screening and polyphenolic antioxidant activity of aqueous crude leaf extract of Helichrysum pedunculatum.

    Aiyegoro, Olayinka A; Okoh, Anthony I

    2009-11-13

    We evaluated the in vitro antioxidant property and phytochemical constituents of the aqueous crude leaf extract of Helichrysum pedunculatum. The scavenging activity on superoxide anions, DPPH, H₂O₂, NO and ABTS; and the reducing power were determined, as well as the flavonoid, proanthocyanidin and phenolic contents of the extract. The extract exhibited scavenging activity towards all radicals tested due to the presence of relatively high total phenol and flavonoids contents. Our findings suggest that H. pedunculatum is endowed with antioxidant phytochemicals and could serve as a base for future drugs.

  1. Composition of the essential oil of Helichrysum chasmolycicum growing wild in Turkey.

    Chalchat, J C; Ozcan, M M

    2006-01-01

    The chemical compositions of the essential oil obtained from the aerial parts of Helichrysum chasmolycicum were analyzed by gas chromatography and gas chromatography-mass spectrometry. From the 57 identified constituents, representing 66.55% of the oil, the main constituents of the oil were beta-caryophyllene (27.6%), beta-selinene (8.9%), alpha-selinene (8.4%), caryophyllene oxide (7.3%), and carvacrol (2.4%). The essential oil was almost totally characterized by sesquiterpene hydrocarbons such as beta-caryophyllene and alpha- and beta-selinene.

  2. Phytochemical Screening and Polyphenolic Antioxidant Activity of Aqueous Crude Leaf Extract of Helichrysum pedunculatum

    Anthony I. Okoh

    2009-11-01

    Full Text Available We evaluated the in vitro antioxidant property and phytochemical constituents of the aqueous crude leaf extract of Helichrysum pedunculatum. The scavenging activity on superoxide anions, DPPH, H2O2, NO and ABTS; and the reducing power were determined, as well as the flavonoid, proanthocyanidin and phenolic contents of the extract. The extract exhibited scavenging activity towards all radicals tested due to the presence of relatively high total phenol and flavonoids contents. Our findings suggest that H. pedunculatum is endowed with antioxidant phytochemicals and could serve as a base for future drugs.

  3. On the metal tolerance and resilience capacity of Helichrysum italicum G. Don growing on mine soils

    Maleci, Laura; Tani, Corrado; Bini, Claudio; Wahsha, Mohammad

    2016-04-01

    Heavy metal accumulation produces significant physiological and biochemical responses in vascular plants. Plants growing on abandoned mine sites are of particular interest, since they are genetically tolerant to high metal concentrations. In this work we examined the effects of heavy metals (HM) on the morphology of Helichrysum italicum growing on mine soils, with the following objectives: to determine the fate of HM within the soil-plant system; to highlight morphological modifications at anatomical and cytological level; to ascertain the plant tolerance to heavy metals, and their resilience capacity. Wild specimens of Helichrysum italicum, with their soil clod, were gathered from sites with different contamination levels by heavy metals (Cd, Cu, Fe, Pb, Zn) in the abandoned Niccioleta mine (Tuscany, Italy). Plants were brought to the botanical laboratory of the University of Florence, and appeared macroscopically not affected by toxic signals (e.g. reduced growth, leaf necrosis) induced by soil HM concentration. Leaves and roots taken at the same growing season were observed by light microscopy (LM) and transmission electron microscopy (TEM). Light microscopy observations show a clear difference in the cell organization of not-contaminated and contaminated samples. In particular, the secreting trichomes, which are responsible for the characteristic flavour of the plant, present a different morphology in the polluted specimens with respect to the not-polluted ones. Indeed, the latter present the typical trichomes of the Asteraceae family, with two lines of cells bearing the secretion accumulated on the apical cuticular space. Trichomes of the polluted plants, instead, present a completely different morphology, with a stalk of 3-4 cells and a large secreting apical cell (i.e. they are capitate hairs). Samples from contaminated sites, moreover, present a palisade parenchyma less organized, and a reduction of leaf thickness proportional to HM concentration. The poor

  4. A Unidirectional DC-DC Autotransformer for DC Grid Application

    Meng Zhou

    2018-03-01

    Full Text Available Conventional unidirectional DC-DC converters for DC grid application employ DC-AC-DC two-stage conversion technology and suffer from high converter cost and power loss. To solve these issues, a unidirectional step-up DC-DC autotransformer (UUDAT and a unidirectional step-down DC-DC autotransformer (DUDAT are studied. The UUDAT and DUDAT are composed of a series connection of diode bridges and voltage source converters. Topologies of UUDAT and DUDAT are detailed. The harmonic and un-controllability issues are discussed. Control and possible application scenarios for UUDAT and DUDAT are depicted. DC fault isolation mechanism and the methods of dimensioning the voltage and power ratings of the components in UUDAT and DUDAT are studied. Extensive simulations on power system level and experiments on a UUDAT and DUDAT prototype verified their technical feasibility.

  5. Yield and level of phenolic compounds in the inflorescence of yellow everlasting Helichrysum arenarium (L. Moench collected from natural sites

    Forycka Anna

    2016-12-01

    Full Text Available Introduction: The inflorescence of Helichrysum arenarium (L. Moench shows anti-inflammatory, antioxidant, detoxifying properties and is traditionally used in liver and biliary tract diseases. Because of its difficult and expensive cultivation, the plant raw material is mainly harvested from natural sites.

  6. Studies of South African medicinal plants: Pt. 2. Caespitin, a new phloroglucinol derivative with antimicrobial properties from Helichrysum caespititium

    Dekker, T.G.; Fourie, T.G.; Snyckers, F.O.; Van der Schyf, C.J. (Central Research Laboratory, Noristan Ltd., Silverton, South Africa)

    1983-12-01

    Extracts from Helichrysum caespititium were found to have antimicrobial activity. Structure elucidation of the active compound, 2-(4-methylpentanoyl)-4-(3-methylbuten-2-yl)-phloroglucinol (caespitin), by means of spectroscopic and X-ray crystallographic analyses, is described.

  7. Intestinal antispasmodic effects of Helichrysum italicum (Roth) Don ssp. italicum and chemical identification of the active ingredients.

    Rigano, Daniela; Formisano, Carmen; Senatore, Felice; Piacente, Sonia; Pagano, Ester; Capasso, Raffaele; Borrelli, Francesca; Izzo, Angelo A

    2013-12-12

    In the Mediterranean Area, the flowers of Helichrysum italicum ssp. italicum are a traditional remedy for the treatment of intestinal complaints and are used as herbal tea for curing digestive, stomachic and intestinal diseases. In order to find scientific evidence for the traditional utilization of this plant, the effect of an ethanolic extract of Helichrysum italicum was investigated by using in vivo and in vitro experimental models. Then, through bioassay-guided fractionation procedures, active component(s) were identified. Contractility in vitro was evaluated by stimulating the isolated ileum, in an organ bath, with acetylcholine and barium chloride; motility in vivo was evaluated by measuring upper gastrointestinal transit, both in control mice and in mice with experimental intestinal inflammation induced by croton oil. Chromatographic separation techniques such as HPLC and silica gel columns have yielded the active principles of Helichrysum italicum. We found that the ethanolic extract of Helichrysum italicum ssp. italicum flowers elicited antispasmodic actions in the isolated mouse ileum and inhibited transit preferentially in the inflamed gut. A bioassay guided fractionation of the extract yielded the known compounds 12-acetoxytremetone (1) and 2,3-dihydro-2-[1-(hydroxymethyl)ethenyl]-5-benzofuranyl]-ethanone (2). Present study supported the traditional use of Helichrysum italicum ssp. italicum flowers for intestinal complaints and through bioassay-guided fractionation procedures from the crude extract we showed that 12-acetoxytremetone (1) and 2,3-dihydro-2-[1-(hydroxymethyl)ethenyl]-5-benzofuranyl]-ethanone (2) acted in a synergistic way to produce an intestinal antispasmodic effect. © 2013 Elsevier Ireland Ltd. All rights reserved.

  8. Synergistic interaction of Helichrysum pedunculatum leaf extracts with antibiotics against wound infection associated bacteria

    OLAYINKA A AIYEGORO

    2009-01-01

    Full Text Available The effect of combinations of the crude methanolic extract of the leaves of Helichrysum pedunculatum and eight first-line antibiotics were investigated by time kill assays against a panel of bacterial strains that have been implicated in wound infections. The plant extract showed appreciable antibacterial activities against the test bacteria with zones of inhibition ranging between 18 and 27 mm, and minimum inhibitory concentrations (MICs varying between 0.1 and 5.0 mg/ml. The MICs of the test antibiotics range between 0.001 and 0.412 mg/ml, and combination of the plant extract and the antibiotics resulted in reduction of bacterial counts by between 0 and 6.63 Log10 cfu/ml. At V2 MIC, 56.81% synergy; 43.19% indifference and no antagonism were observed, and at MIC levels, 55.68% synergy; 44.32% indifference and no antagonism were observed when the extracts were combined with eight different antibiotics. In all, 60% of the interactions were synergistic. All combination regimes on Staphylococcus aureus ATCC 6538 yielded no synergy, neither was antagonism detected in any of the assays. We propose that extracts of the leaves of Helichrysum pedunculatum could be of relevance in combination therapy and as a source of resistance modifying principies that could be useful as treatment options for persistent wound infections.

  9. Morphological and genetic evidence of contemporary intersectional hybridisation in Mediterranean Helichrysum (Asteraceae, Gnaphalieae).

    Galbany-Casals, M; Carnicero-Campmany, P; Blanco-Moreno, J M; Smissen, R D

    2012-09-01

    Hybridisation is considered an important evolutionary phenomenon in Gnaphalieae, but contemporary hybridisation has been little explored within the tribe. Here, hybridisation between Helichrysum orientale and Helichrysum stoechas is studied at two different localities in the islands of Crete and Rhodes (Greece). Using three different types of molecular data (AFLP, nrDNA ITS sequences and cpDNA ndhF sequences) and morphological data, the aim is to provide simultaneous and direct comparisons between molecular and morphological variation among the parental species and the studied hybrid populations. AFLP profiles, ITS sequences and morphological data support the existence of hybrids at the two localities studied, shown as morphological and genetic intermediates between the parental species. Chloroplast DNA sequences show that both parental species can act either as pollen donor or as maternal parent. Fertility of hybrids is demonstrated by the viability of seeds produced by hybrids from both localities, and the detection of a backcross specimen to H. orientale. Although there is general congruence of morphological and molecular data, the analysis of morphology and ITS sequences can fail to detect backcross hybrids. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

  10. Synergistic interaction of Helichrysum pedunculatum leaf extracts with antibiotics against wound infection associated bacteria.

    Aiyegoro, Olayinka A; Afolayan, Anthony J; Okoh, Anthony I

    2009-01-01

    The effect of combinations of the crude methanolic extract of the leaves of Helichrysum pedunculatum and eight first-line antibiotics were investigated by time kill assays against a panel of bacterial strains that have been implicated in wound infections. The plant extract showed appreciable antibacterial activities against the test bacteria with zones of inhibition ranging between 18 and 27 mm, and minimum inhibitory concentrations (MICs) varying between 0.1 and 5.0 mg/ml. The MICs of the test antibiotics range between 0.001 and 0.412 mg/ml, and combination of the plant extract and the antibiotics resulted in reduction of bacterial counts by between 0 and 6.63 Log10 cfu/ml. At V2 MIC, 56.81% synergy; 43.19% indifference and no antagonism were observed, and at MIC levels, 55.68% synergy; 44.32% indifference and no antagonism were observed when the extracts were combined with eight different antibiotics. In all, 60% of the interactions were synergistic. All combination regimes on Staphylococcus aureus ATCC 6538 yielded no synergy, neither was antagonism detected in any of the assays. We propose that extracts of the leaves of Helichrysum pedunculatum could be of relevance in combination therapy and as a source of resistance modifying principies that could be useful as treatment options for persistent wound infections.

  11. Characteristic thickened cell walls of the bracts of the 'eternal flower' Helichrysum bracteatum.

    Nishikawa, Kuniko; Ito, Hiroaki; Awano, Tatsuya; Hosokawa, Munetaka; Yazawa, Susumu

    2008-07-01

    Helichrysum bracteatum is called an 'eternal flower' and has large, coloured, scarious bracts. These maintain their aesthetic value without wilting or discoloration for many years. There have been no research studies of cell death or cell morphology of the scarious bract, and hence the aim of this work was to elucidate these characteristics for the bract of H. bracteatum. DAPI (4'6-diamidino-2-phenylindol dihydrochloride) staining and fluorescence microscopy were used for observation of cell nuclei. Light microscopy (LM), transmission electron microscopy (TEM) and polarized light microscopy were used for observation of cells, including cell wall morphology. Cell death occurred at the bract tip during the early stage of flower development. The cell wall was the most prominent characteristic of H. bracteatum bract cells. Characteristic thickened secondary cell walls on the inside of the primary cell walls were observed in both epidermal and inner cells. In addition, the walls of all cells exhibited birefringence. Characteristic thickened secondary cell walls have orientated cellulose microfibrils as well as general secondary cell walls of the tracheary elements. For comparison, these characters were not observed in the petal and bract tissues of Chrysanthemum morifolium. Bracts at anthesis are composed of dead cells. Helichrysum bracteatum bracts have characteristic thickened secondary cell walls that have not been observed in the parenchyma of any other flowers or leaves. The cells of the H. bracteatum bract differ from other tissues with secondary cell walls, suggesting that they may be a new cell type.

  12. Helichrysum arenarium subsp. arenarium: phenolic composition and antibacterial activity against lower respiratory tract pathogens.

    Gradinaru, Adina C; Silion, Mihaela; Trifan, Adriana; Miron, Anca; Aprotosoaie, Ana C

    2014-01-01

    The aim of this study was to investigate the phenolic content and antibacterial activity of the methanol extract from Helichrysum arenarium (L.) Moench subsp. arenarium inflorescences against lower respiratory tract pathogens (standard strains and clinical isolates). The extract was characterised by a total phenolic content of 160.17 mg/g. Several caffeic acid conjugates (chlorogenic acid and dicaffeoylquinic acids) and flavonoids (apigenin, naringenin, apigenin-7-O-glucoside and naringenin-O-hexosides) were identified as major constituents by HPLC-DAD-ESI-MS. Staphylococcus aureus ATCC 25923 was more susceptible to Helichrysum extract than Streptococcus pneumoniae ATCC 49619 (minimum inhibitory concentration [MIC] = 0.62  and 1.25 mg/mL, respectively). The extract exhibited similar antibacterial effects against methicillin-resistant S. aureus and penicillin-resistant S. pneumoniae clinical isolates (MIC = 2.5 mg/mL) displaying a higher activity against ampicillin-resistant Moraxella catarrhalis isolate (MIC = 0.15 mg/mL). The combination with ciprofloxacin exhibited additivity against both standard strains (fractional inhibitory concentration [FIC] index = 0.75 and 0.73) and S. aureus isolates (FIC index = 0.62) and synergy against S. pneumoniae isolates (FIC index = 0.5).

  13. Antihistaminic and antieicosanoid effects of oleanolic and ursolic acid fraction from Helichrysum picardii.

    Santos Rosa, C; García Gimenez, M D; Saenz Rodriguez, M T; De la Puerta Vazquez, R

    2007-06-01

    Helichrysum picardii Boiss. & Reuter is a Mediterranean vegetal species from the Asteraceae family. From the methanolic extract of the aerial flowering parts of this plant, a fraction of two pentacyclic triterpenes has been isolated. Gas chromatography revealed that the triterpene isomers ursolic and oleanolic acids comprised 69% and 29% respectively of the composition of this fraction. The triterpene isomeric fraction was tested in two phagocyte cell systems. It inhibited compound 48/80-induced histamine release from rat peritoneal mast cells in an approximately percentage of 45% at 100 microM and myeloperoxidase secretion from A23187-ionophore-stimulated rat peritoneal leukocytes in a significant manner at doses of 50 and 100 miroM. Furthermore, the triterpene isomers very significantly and dose-dependently inhibited generation of the cyclo-oxygenase metabolite prostaglandin E2 (41% inhibition at 50 miroM) and the 5-lipoxygenase metabolite leukotriene B4 (79% inhibition at 50 microM) from activated rat leukocytes. This anti-eicosanoid activity of the triterpene fraction was more potent than that produced by the pure triterpene oleanolic acid used for comparision, indicating a stronger action of the ursolic acid, the major compound of the isolated triterpene fraction. From these data, it can be suggested that the triterpene isomers oleanolic and ursolic acids present in the medicinal plant Helichrysum picardii contribute to the anti-inflammatory profile of this vegetal species.

  14. Essential Oil Composition and Volatile Profile of Seven Helichrysum Species Grown in Italy.

    Giovanelli, Silvia; De Leo, Marinella; Cervelli, Claudio; Ruffoni, Barbara; Ciccarelli, Daniela; Pistelli, Luisa

    2018-03-06

    Helichrysum genus consists of about 600 species widespread throughout the world, especially in South Africa and in the Mediterranean area. In this study the aroma profile (HS-SPME) and the EO compositions of seven Helichrysum species (H. cymosum, H. odoratissimum, H. petiolare, H. fontanesii, H. saxatile, H. sanguineum, and H. tenax) were evaluated. All the plants were grown in Italy under the same growth conditions. The volatile constituents, particularly monoterpenes, depended by the plant's genotype and ecological adaptation. This study represents the first headspace evaluation on the selected plants and the results evidenced that monoterpenes represented the main class of constituents in five of the seven species analysed (from 59.2% to 95.0%). The higher content in sesquiterpene hydrocarbons was observed in the Mediterranean species of H. sanguineum (68.0%). Only H. saxatile showed relative similar abundance of monoterpenes and sesquiterpene hydrocarbons. The essential oil composition of the majority of examined species are characterised by high percentage of sesquiterpenes (especially β-caryophyllene and δ-cadinene) ranging from 51.3% to 92.0%, except for H. cymosum, H. tenax, and H. sanguineum leaves where monoterpenes predominated (from 51.7% to 74.7%). © 2018 Wiley-VHCA AG, Zurich, Switzerland.

  15. Step-Up DC-DC converters

    Forouzesh, Mojtaba; Siwakoti, Yam P.; Gorji, Saman A.

    2017-01-01

    on the general law and framework of the development of next-generation step-up dc-dc converters, this paper aims to comprehensively review and classify various step-up dc-dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage...

  16. DC Home Appliances for DC Distribution System

    MUHAMMAD KAMRAN

    2017-10-01

    Full Text Available This paper strengthens the idea of DC distribution system for DC microgrid consisting of a building of 50 apartments. Since the war of currents AC system has been dominant because of the paucity of research in the protection of the DC system. Now with the advance research in power electronics material and components, generation of electricity is inherently DC as by solar PV, fuel cell and thermoelectric generator that eliminates the rectification process. Transformers are replaced by the power electronics buck-boost converters. DC circuit breakers have solved the protection problems for both DC transmission and distribution system. In this paper 308V DC microgrid is proposed and home appliances (DC internal are modified to operate on 48V DC from DC distribution line. Instead of using universal and induction motors in rotary appliances, BLDC (Brushless DC motors are proposed that are highly efficient with minimum electro-mechanical and no commutation losses. Proposed DC system reduces the power conversion stages, hence diminishes the associated power losses and standby losses that boost the overall system efficiency. So in view of all this a conventional AC system can be replaced by a DC system that has many advantages by cost as well as by performance

  17. Step-Up DC-DC converters

    Forouzesh, Mojtaba; Siwakoti, Yam P.; Gorji, Saman A.

    2017-01-01

    on the general law and framework of the development of next-generation step-up dc-dc converters, this paper aims to comprehensively review and classify various step-up dc-dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage......DC-DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which......-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc-dc converters are presented and summarized with comparative study of different voltage-boosting techniques....

  18. Interactions of antibiotics and extracts of Helichrysum pedunculatum against bacteria implicated in wound infections.

    Aiyegoro, O A; Afolayan, A J; Okoh, A I

    2010-03-01

    The effect of combinations of the crude acetone and aqueous extracts of Helichrysum pedunculatum leaves and eight antibiotics was determined by means of checkerboard and time-kill methods. In the checkerboard method, synergy of 45.8% was observed, being independent of Gram reaction, with combinations in the aqueous extract yielding largely (18.8%) antagonistic interactions. The time-kill assay detected synergy (45.8%) that was also independent of Gram reaction with a potentiation of more than 3 orders of the bactericidal activity of the test antibiotics. The crude leaf extracts of H. pedunculatum could thus be considered to be potential source of a broad-spectrum antibiotic-resistance-modifying compounds.

  19. Antimicrobial monomeric and dimeric diterpenes from the leaves of Helichrysum tenax var tenax.

    Drewes, Siegfried E; Mudau, K Esther; van Vuuren, Sandy F; Viljoen, Alvaro M

    2006-04-01

    The hexane extract of fresh air-dried leaves of Helichrysum tenax (Asteraceae) afforded ent-beyer-15-en-19-ol (1), its 4-epimer ent-beyer-15-en-18-ol (2), 15beta,16beta-epoxide-ent-beyeran-19-ol (3), as well as (4) consisting of two units of (1) linked as a diester of malonic acid, and (5), a compound. Its constituents are (1) and (3) also linked as a diester of malonic acid. The leaves of the plant are densely covered in fine glandular trichomes. These are extremely sticky and exude a mixture of the above diterpenes. Antimicrobial tests showed that (1), in particular, was highly active (3.1 and 3.6 microg/ml) against Bacillus cereus and Staphylococcus epidermidis, respectively.

  20. The impact of habitat conditions on blooming of Helichrysum arenarium (L. Moench

    Anna K. Sawilska

    2012-12-01

    Full Text Available Helichrysum arenarium (L. Moench is a perennial belonging to the Asteraceae family. It is used as a herb material. The species is under partial protection. The aim of the study was to determine the influence of the community type and weather conditions on blooming of everlasting. Growth and development dynamics vs. habitat factors were analyzed in detail. The results of this study indicate that blooming process of everlasting populations remains under influence of habitat factors, which is evidenced by a decrease of potential fertility paralleled by an increase of number of taxa found in phytocoenosis. Blooming process is also modified by weather conditions: the potential fertility index is significantly correlated with precipitation.

  1. Two structurally distinct chalcone dimers from Helichrysum zivojinii and their activities in cancer cell lines.

    Aljančić, Ivana S; Vučković, Ivan; Jadranin, Milka; Pešić, Milica; Dorđević, Iris; Podolski-Renić, Ana; Stojković, Sonja; Menković, Nebojša; Vajs, Vlatka E; Milosavljević, Slobodan M

    2014-02-01

    Dimers tomoroside A (1) and tomoroside B (2) of the co-occuring known chalcone monomer (3), along with the seven known flavonoid glucosides (4-10), were isolated from the aerial parts of Helichrysum zivojinii Černjavski & Soška. The structures of the isolated compounds were elucidated by spectroscopic techniques. Compound 1 inhibited topo IIα and hif-1α expression and stimulated doxorubicin anticancer effect, while 2 increased the expression of hif-1α, probably acting as antioxidant and redox status modulator. Notably, 2 synergized with Tipifarnib showing potential to improve the action of this new chemotherapeutic involved in the modulation of mitogene activated protein (MAP) kinase signaling pathway. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. DC electric springs with DC/DC converters

    Wang, Qingsong; Cheng, Ming; Jiang, Yunlei

    2016-01-01

    The concept of DC electric spring (DCES) was recently proposed to solve the stability issue caused by integrating intermittent renewable energy sources (RESs) to DC microgrids. In this paper, a new topology of DCES is proposed based on DC/DC converters. The proposed DCES consists of a bi-directio......The concept of DC electric spring (DCES) was recently proposed to solve the stability issue caused by integrating intermittent renewable energy sources (RESs) to DC microgrids. In this paper, a new topology of DCES is proposed based on DC/DC converters. The proposed DCES consists of a bi...... and/or constant discharging for batteries is adopted and four operating modes are analyzed as charging-positive, charging-negative, discharging-positive and discharging-negative modes. An additional mechanism for fast charging or fast discharging is also designed to secure normal operation...... of batteries. With the proposed DCES, the power fluctuations due to intermittent RESs can be passed to non-critical loads (NCLs) and batteries while power on critical loads (CLs) is kept stable. This is possibly the first attempt to design a DCES with only DC/DC converters. The performances of the proposed...

  3. Supercritical Extraction of Scopoletin from Helichrysum italicum (Roth) G. Don Flowers.

    Jokić, Stela; Rajić, Marina; Bilić, Blanka; Molnar, Maja

    2016-09-01

    The increasing popularity of immortelle (Helichrysum italicum (Roth) G. Don) and its products, particularly in the cosmetic industry, is evident nowadays. This plant is a source of coumarins, especially scopoletin, which are highly soluble in supercritical CO2 . The objective of this study was to perform the supercritical CO2 extraction process of Helichrysum italicum flowers at different values of pressure and temperature and to optimise the extraction process using response surface methodology in terms of obtaining the highest extraction yield and yield of extracted scopoletin. Extraction was performed in a supercritical extraction system under different extraction conditions of pressure and temperature determined by central composite rotatable design. The mass of flowers in the extractor of 40 g, extraction time of 90 min and CO2 mass flow rate of 1.94 kg/h were kept constant during experiments. Antioxidant activity was determined using the DPPH (1,1-diphenyl-2-picrylhydrazyl) free radical scavenging assay method. Scopoletin concentration was determined by HPLC. Changes in extraction conditions affect the extracting results remarkably. The greatest extraction yield (6.31%) and the highest yield of scopoletin (1.933 mg/100 g) were obtained under extraction conditions of 20 MPa and 40°C. Extracts have also proven to possess antioxidant activity (44.0-58.1% DPPH scavenging activity) influenced by both temperature and pressure applied within the investigated parameters. The extraction conditions, especially pressure, exhibited significant influence on the extraction yield as well as the yield of extracted scopoletin and antioxidant activity of extracts. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  4. Characteristic Thickened Cell Walls of the Bracts of the ‘Eternal Flower’ Helichrysum bracteatum

    Nishikawa, Kuniko; Ito, Hiroaki; Awano, Tatsuya; Hosokawa, Munetaka; Yazawa, Susumu

    2008-01-01

    Background and Aims Helichrysum bracteatum is called an ‘eternal flower’ and has large, coloured, scarious bracts. These maintain their aesthetic value without wilting or discoloration for many years. There have been no research studies of cell death or cell morphology of the scarious bract, and hence the aim of this work was to elucidate these characteristics for the bract of H. bracteatum. Methods DAPI (4'6-diamidino-2-phenylindol dihydrochloride) staining and fluorescence microscopy were used for observation of cell nuclei. Light microscopy (LM), transmission electron microscopy (TEM) and polarized light microscopy were used for observation of cells, including cell wall morphology. Key Results Cell death occurred at the bract tip during the early stage of flower development. The cell wall was the most prominent characteristic of H. bracteatum bract cells. Characteristic thickened secondary cell walls on the inside of the primary cell walls were observed in both epidermal and inner cells. In addition, the walls of all cells exhibited birefringence. Characteristic thickened secondary cell walls have orientated cellulose microfibrils as well as general secondary cell walls of the tracheary elements. For comparison, these characters were not observed in the petal and bract tissues of Chrysanthemum morifolium. Conclusions Bracts at anthesis are composed of dead cells. Helichrysum bracteatum bracts have characteristic thickened secondary cell walls that have not been observed in the parenchyma of any other flowers or leaves. The cells of the H. bracteatum bract differ from other tissues with secondary cell walls, suggesting that they may be a new cell type. PMID:18436550

  5. Population genetic analysis and evidence of inter-specific introgression in Helichrysum armenium and H. rubicundum (Asteraceae

    Taban Malahat

    2015-01-01

    Full Text Available Helichrysum armenium and H. rubicundum are two medicinally important plants of Iran that are distributed in various regions of the country. They are extensively used by locals as medicinal plants and a great negative selection pressure is applied on them. Therefore, due to importance of these plant species, we performed a population genetic study in both species. For this study, we used 66 randomly collected plants from 24 geographical populations of Helichrysum armenium and H. rubicundu. These species had areas of overlap and contact and we found some intermediate plants that were included in our study too. UPGMA and MDS analyses revealed morphological separation of these closely related species and placed intermediate plants in an intermediate position. ISSR analysis revealed inter-population genetic diversity and K-Means clustering and STRUCTURE analyses revealed populations. Genetic stratification in both species. Genetic difference of the studied populations was not correlated to geographical distance. Triangle plot of Bayesian analysis and NeighborNet plot showed inter-specific gene flow. The studied populations showed plants with 2n = 2x = 14 and 2n = 4x = 28 chromosomes and differed significantly in their meiotic behavior. Therefore, a combination of genetic stratification, and genetic admixture as well as polyploidy and chromosomes structural changes, have played rule in Helichrysum diversification.

  6. Modulation of hyperglycemia and TNFα-mediated inflammation by helichrysum and grapefruit extracts in diabetic db/db mice.

    de la Garza, Ana Laura; Etxeberria, Usune; Palacios-Ortega, Sara; Haslberger, Alexander G; Aumueller, Eva; Milagro, Fermín I; Martínez, J Alfredo

    2014-09-01

    Type-2 diabetes is associated with a chronic low-grade systemic inflammation accompanied by an increased production of adipokines/cytokines by obese adipose tissue. The search for new antidiabetic drugs with different mechanisms of action, such as insulin sensitizers, insulin secretagogues and α-glucosidase inhibitors, has directed the focus on the potential use of flavonoids in the management of type-2 diabetes. Thirty six diabetic male C57BL/6J db/db mice were fed a standard diet and randomly assigned into four experimental groups: non-treated control, (n = 8); acarbose (5 mg per kg bw, n = 8); helichrysum (1 g per kg bw, n = 10) and grapefruit (0.5 g per kg bw, n = 10) for 6 weeks. The mRNA expression in pancreas, liver and epididymal adipose tissue was determined by RT-PCR. DNA methylation was quantified in epididymal fat using pyrosequencing. Mice supplemented with helichrysum and grapefruit extracts showed a significant decrease in fasting glucose levels (p helichrysum and grapefruit extracts improved hyperglycemia through the regulation of glucose metabolism in the liver and reduction of the expression of proinflammatory genes in the liver and visceral fat. The hypermethylation of TNFα in adipose tissue may contribute to reduce the inflammation associated with diabetes and obesity.

  7. Genetic variation in Mediterranean Helichrysum italicum (Asteraceae; Gnaphalieae): do disjunct populations of subsp. microphyllum have a common origin?

    Galbany-Casals, M; Blanco-Moreno, J M; Garcia-Jacas, N; Breitwieser, I; Smissen, R D

    2011-07-01

    The yellow-flowered everlasting daisy Helichrysum italicum (Asteraceae, Gnaphalieae) is widely distributed in the Mediterranean basin, where it grows in continuous and widespread populations in diverse open habitats. Helichrysum italicum subsp. microphyllum has a disjunct distribution in the Balearic Islands (Majorca and Dragonera), Corsica, Sardinia, Crete and Cyprus. Numerous morphological intermediates between subsp. italicum and subsp. microphyllum are known from Corsica, where the two subspecies co-occur. The aims of the study were to investigate if subsp. microphyllum has a common origin, constituting an independent gene pool from subsp. italicum, or if the morphological differences between subsp. microphyllum and subsp. italicum have arisen independently in different locations from a common wider gene pool. Our analyses of AFLP, cpDNA sequences and morphological characters show that there is geographic structure to the genetic variation within H. italicum, with eastern and western Mediterranean groups, which do not correspond with the division into subsp. microphyllum and subsp. italicum as currently circumscribed. Local selection on quantitative trait loci provides sufficient explanation for the morphological divergence observed and is consistent with genetic data. Within the western Mediterranean group of the species we found considerable polymorphism in chloroplast DNA sequences among and within some populations. Comparison with chloroplast DNA sequences from other Helichrysum species showed that some chloroplast haplotypes are shared across species. © 2010 German Botanical Society and The Royal Botanical Society of the Netherlands.

  8. In vivo antidiabetic and antioxidant potential of Helichrysum plicatum ssp. plicatum capitulums in streptozotocin-induced-diabetic rats.

    Aslan, Mustafa; Deliorman Orhan, Didem; Orhan, Nilüfer; Sezik, Ekrem; Yesilada, Erdem

    2007-01-03

    Helichrysum species (Asteraceae) are widely found in Anatolia. Decoction prepared from the capitulums of Helichrysum plicatum ssp. plicatum is used to alleviate the symptoms of diabetes mellitus in folk medicine. In the present study, the hypoglycaemic and antioxidant potential of Helichrysum plicatum ssp. plicatum was evaluated by using in vivo methods in normal and streptozotocin-induced-diabetic rats. After the oral administration of water and ethanolic extracts at doses of 500mg/kg body weight prepared from the capitulums of plant, blood glucose levels were monitored at specific intervals. Tolbutamide was used as a reference drug at a dose of 100mg/kg. The experimental data indicated that water and ethanol extracts of capitulums demonstrate significant antihyperglycaemic and antioxidant activity in streptozotocin-induced rats which confirmed the folkloric utilization. In order to assess the role of polyphenolic components in the relevant activity, phenolic and flavonoid contents of each extract were also determined in terms of total phenols: 113.5+/-8.6mg (gallic acid equivalent/1g extract) and total flavanoids 50.5+/-1.9mg (quercetin equivalent/1g extract) for ethanol extract, total phenols: 75.9+/-3.7, flavonoids: 31.5+/-2.3 for water extract using Folin-Ciocalteu reagent.

  9. A resonant dc-dc power converter assembly

    2015-01-01

    The present invention relates to a resonant DC-DC power converter assembly comprising a first resonant DC-DC power converter and a second resonant DC-DC power converter having identical circuit topologies. A first inductor of the first resonant DC-DC power converter and a second inductor of the s......The present invention relates to a resonant DC-DC power converter assembly comprising a first resonant DC-DC power converter and a second resonant DC-DC power converter having identical circuit topologies. A first inductor of the first resonant DC-DC power converter and a second inductor...... of the second resonant DC-DC power converter are configured for magnetically coupling the first and second resonant DC-DC power converters to each other to forcing substantially 180 degrees phase shift, or forcing substantially 0 degree phase shift, between corresponding resonant voltage waveforms of the first...

  10. Exploration of the wound healing potential of Helichrysum graveolens (Bieb.) Sweet: isolation of apigenin as an active component.

    Süntar, Ipek; Küpeli Akkol, Esra; Keles, Hikmet; Yesilada, Erdem; Sarker, Satyajit D

    2013-08-26

    In Turkish traditional medicine, the flowers of Helichrysum graveolens (Bieb.) Sweet (Asteraceae) have been used for the treatment of jaundice, for wound-healing and as a diuretic. In order to find scientific evidence for the traditional utilization of this plant in wound-healing, the effect of the plant extract was investigated by using in vivo and in vitro experimental models. Then through bioassay-guided fractionation procedures active wound-healing component(s) was isolated and its possible role in the wound-healing process was also determined. The linear incision and the circular excision wound models were applied in order to evaluate in vivo wound-healing potential of Helichrysum graveolens. Anti-inflammatory and antioxidant activities, which are known to involve in wound-healing process, were also assessed by the Whittle method and the DPPH (2,2-diphenyl-1-picrylhydrazyl) radical-scavenging assay, respectively. The total phenolic content of the crude extract and solvent fractions was estimated to find correlation between the phenolic content and the antioxidant activity. Combined application of the chromatographic separation techniques on sephadex and silica gel columns, and bioassay techniques have yielded the active wound-healing principle of Helichrysum graveolens. Moreover, in vitro inhibitory effect of active principle on hyaluronidase, collagenase and elastase enzymes were investigated to explore the activity pathways. The 85% methanol (MeOH) extract of Helichrysum graveolens flowers displayed significant wound-healing, anti-inflammatory and antioxidant activities. Then the crude extract was partitioned by successive solvent extractions, in increasing polarity, to give five solvent fractions. Among the solvent fractions, the ethyl acetate (EtOAc) fraction exerted the highest activity. The EtOAc fraction was further subjected to chromatographic separations to yield active constituent and its structure was elucidated to be apigenin by spectrometric

  11. IGBT Based DC/DC Converter

    M. Akherraz

    1997-12-01

    Full Text Available This paper presents an in-depth analytical and experimental investigation of an indirect DC-DC converter. The DC-AC conversion is a full bridge based on IGBT power modules, and the AC-DC conversion is done via a high  frequency AC link and a first diode bridge. The AC link, which consists of snubbing capacitors and a variable air-gap transformer, is analytically designed to fulfill Zero Voltage commutation requirement. The proposed converter is simulated using PSPICE and a prototype is designed built and tested in the laboratory. PSPICE simulation and experimental results are presented and compared.

  12. A resonant dc-dc power converter assembly

    Madsen, Mickey Pierre

    2015-01-01

    The present invention relates to a resonant DC-DC power converter assembly comprising a first resonant DC-DC power converter and a second resonant DC-DC power converter having identical circuit topologies. A first inductor of the first resonant DC-DC power converter and a second inductor of the second resonant DC-DC power converter are configured for magnetically coupling the first and second resonant DC-DC power converters to each other to forcing substantially 180 degrees phase shift, or fo...

  13. Influence of mycorrhizal fungi on the growth and development of sandy everlasting Helichrysum arenarium (L. Moench.

    Anna K. Sawilska

    2012-12-01

    Full Text Available The significance of root colonization by mycorrhizal fungi for the growth and development of Helichrysum arenarium was investigated in two independent experiments. In the first experiment the association of root colonization level with the pluviothermal conditions within the growing season and the age of a natural plant population was analyzed. In the second one, under controlled conditions, the influence of artificial inoculation with the arbuscular fungus Glomus intraradices on the features of plants raised from achenes was studied. It was shown that hydrothermal conditions during blooming period had a greater influence on reproduction processes of sandy everlasting than both the population age (the secondary succession progress and the level of root colonization by mycorrhizal fungi. High amount of precipitation at plant generative development phase positively influences the potential and actual fertility of ramets. The presence of arbuscular fungus in the soil favors the growth and development of sandy everlasting specimens at their early growing stages: they have a better-developed root system and a greater photosynthetic area.

  14. Identification and quantitative determination of the polar constituents in Helichrysum italicum flowers and derived food supplements.

    Mari, Angela; Napolitano, Assunta; Masullo, Milena; Pizza, Cosimo; Piacente, Sonia

    2014-08-05

    Helichrysum italicum is widely used in traditional medicine, in cosmetic, in food and pharmaceutical field. In spite of this, very little is known about the chemical composition of its polar extracts. Therefore this study was addressed to the determination of the metabolite profile of the methanol extract of H. italicum flowers, by using LC-ESI(IT)MSMS. This approach oriented the isolation of 14 compounds, whose structures were unambiguously elucidated by NMR as belonging to flavonoid, phenylpropanoid and acylbenzofuran classes. In addition, one novel drimane sesquiterpene was identified. The quantitative determination of the main compounds occurring in the methanol extract of H. italicum flowers was carried out and their content was compared with that of three selected commercial food supplements based on H. italicum, by using LC-ESI(QqQ)MS. In conclusion the wide occurrence, in high amounts, of quinic acid derivatives in all the analyzed samples was highlighted, showing these compounds as chemical markers of the species for standardization procedures. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Dipeptidyl peptidase-IV inhibitory activity of dimeric dihydrochalcone glycosides from flowers of Helichrysum arenarium.

    Morikawa, Toshio; Ninomiya, Kiyofumi; Akaki, Junji; Kakihara, Namiko; Kuramoto, Hiroyuki; Matsumoto, Yurie; Hayakawa, Takao; Muraoka, Osamu; Wang, Li-Bo; Wu, Li-Jun; Nakamura, Seikou; Yoshikawa, Masayuki; Matsuda, Hisashi

    2015-10-01

    A methanol extract of everlasting flowers of Helichrysum arenarium L. Moench (Asteraceae) was found to inhibit the increase in blood glucose elevation in sucrose-loaded mice at 500 mg/kg p.o. The methanol extract also inhibited the enzymatic activity against dipeptidyl peptidase-IV (DPP-IV, IC50 = 41.2 μg/ml), but did not show intestinal α-glucosidase inhibitory activities. From the extract, three new dimeric dihydrochalcone glycosides, arenariumosides V-VII (2-4), were isolated, and the stereostructures were elucidated based on their spectroscopic properties and chemical evidence. Of the constituents, several flavonoid constituents, including 2-4, were isolated, and these isolated constituents were investigated for their DPP-IV inhibitory effects. Among them, chalconaringenin 2'-O-β-D-glucopyranoside (16, IC50 = 23.1 μM) and aureusidin 6-O-β-D-glucopyranoside (35, 24.3 μM) showed relatively strong inhibitory activities.

  16. Antioxidant Capacity, Cytotoxicity and Antimycobacterial Activity of Madeira Archipelago Endemic Helichrysum Dietary and Medicinal Plants

    Sandra C. Gouveia-Figueira

    2014-10-01

    Full Text Available The potential bioactivity of dietary and medicinal endemic Helichrysum plants from Madeira Archipelago was explored, for the first time, in order to supply new information for the general consumer. In vitro antioxidant properties were investigated using DPPH, ABTS•+, FRAP and β-Carotene assays, and the total phenolic content (TPC and total flavonoid content (TFC were also determined. Although the results generally showed a large variation among the three analyzed plants, the methanolic extracts showed the highest antioxidant capacity. Exception is made for H. devium n-hexane extract that showed good radical scavenger capacity associated to compounds with good reducing properties. In the Artemia salina toxicity assay and antimycobaterial activity, H. devium was the most potent plant with the lowest LD50 at 216.7 ± 10.4 and MIC ≤ 50 μg·mL−1. Chemometric evaluation (Principal Component Analysis—PCA showed close interdependence between the ABTS, TPC and TFC methods and allowed to group H. devium samples.

  17. Improved metabolic control and hepatic oxidative biomarkers with the periconception use of Helichrysum plicatum ssp. plicatum.

    Sezik, M; Aslan, M; Orhan, D D; Erdemoglu, E; Pekcan, M; Mungan, T; Sezik, E

    2010-02-01

    Our aim was to investigate the hypoglycaemic and antioxidant effects of the Helichrysum plicatum ssp. plicatum (HPsP) plant extract in the streptozotocin-induced type 1 diabetes rat model during pregnancy. Five groups (n = 8, each) were formed: (1) diabetic non-mated control, (2) non-diabetic mated control, (3) diabetic mated control, (4) diabetic non-mated treatment and (5) diabetic mated treatment. The HPsP extract was administered orally for 15 days (250 mg/kg body weight), beginning 3 days before mating. The extract led to decreased blood glucose, increased serum insulin, and decreased serum triglycerides in pregnant and non-pregnant diabetic animals. Liver thiobarbituric acid reactive substances (TBARS) and reduced glutathione (GSH) measurements in extract-treated diabetics were similar to non-diabetic pregnant controls, indicating probable reversal of increased lipid peroxidation in the liver. The mean pup number tended to increase (p = 0.06) with extract administration. In conclusion, the beneficial effects we encountered with the periconception use of the studied herbal extract warrant further investigation.

  18. A new acetophenone derivative from flowers of Helichrysum italicum (Roth) Don ssp. italicum.

    Rigano, Daniela; Formisano, Carmen; Pagano, Ester; Senatore, Felice; Piacente, Sonia; Masullo, Milena; Capasso, Raffaele; Izzo, Angelo A; Borrelli, Francesca

    2014-12-01

    A new acetophenone derivative named gnaphaliol 9-O-propanoate (1) was isolated from the chloroform fraction of EtOH extract of Helichrysum italicum ssp. italicum flowers along with the five known acetophenones 12-acetoxytremetone (2), 13-(2-methylpropanoyloxy)toxol (3), [2,3-dihydro-2-[1-(hydroxymethyl)ethenyl]-5-benzofuranyl]-ethanone (4), 1-[2-[1-[(acetyloxy)methyl]ethenyl]-2,3-dihydro-3-hydroxy-5-benzofuranyl]-ethanone (5) and gnaphaliol (6). The structures of compounds 1-6 were elucidated by extensive spectroscopic methods including 1D- ((1)H and (13)C) and 2D-NMR (DQF-COSY, HSQC, HMBC, TOCSY and ROESY) experiments as well as ESIMS analysis. The isolated compounds were investigated for their cytotoxicity, anti-inflammatory and antioxidant properties. Biological assays on human colonic epithelial cells showed that compound 2 possessed antioxidant effects reducing reactive oxygen species (ROS) production. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. A new glucosidic phthalide from Helichrysum microphyllum subsp. tyrrhenicum from La Maddalena Island (Sardinia, Italy).

    Venditti, Alessandro; Lattanzi, Claudia; Ornano, Luigi; Maggi, Filippo; Sanna, Cinzia; Ballero, Mauro; Alvino, Antonello; Serafini, Mauro; Bianco, Armandodoriano

    2016-01-01

    In this study, we reported the analysis of the medium polarity fraction obtained from an accession of Helichrysum microphyllum subsp. tyrrhenicum from La Maddalena Island. Besides several compounds already evidenced in this species and related genera, i.e. micropyrone (1), arzanol (2), helipyrone (3), acetyl-bitalin derivatives (4, 5), gnaphaliol (6), caffeic acid (7), ursolic acid (8), 7-O-β-(D-glucopyranosyl)-5-methoxy-1(3H)-isobenzofuranone (9), gnaphaliol-9-O-β-D-glucopyranoside (11) and gnaphaliol-3-O-β-D-glucopyranoside (12), the presence of a new glycosidic phthalide, 6-O-β-(D-glucopyranosyl)-4-methoxy-1(3H)-benzofuranone (10), was evidenced for the first time, which resulted in a structural isomer of compound (9). The occurrence of this new benzofuranone derivative is an additional evidence of the deep intraspecific variability expressed by this species, which was also stated for the non-volatile components, and may be a distinctive trait of the population growing on La Maddalena Island.

  20. Antioxidant Capacity, Cytotoxicity and Antimycobacterial Activity of Madeira Archipelago Endemic Helichrysum Dietary and Medicinal Plants.

    Gouveia-Figueira, Sandra C; Gouveia, Carla A; Carvalho, Maria J; Rodrigues, Ana I; Nording, Malin L; Castilho, Paula C

    2014-10-31

    The potential bioactivity of dietary and medicinal endemic Helichrysum plants from Madeira Archipelago was explored, for the first time, in order to supply new information for the general consumer. In vitro antioxidant properties were investigated using DPPH, ABTS(•+), FRAP and β-Carotene assays, and the total phenolic content (TPC) and total flavonoid content (TFC) were also determined. Although the results generally showed a large variation among the three analyzed plants, the methanolic extracts showed the highest antioxidant capacity. Exception is made for H. devium n-hexane extract that showed good radical scavenger capacity associated to compounds with good reducing properties. In the Artemia salina toxicity assay and antimycobaterial activity, H. devium was the most potent plant with the lowest LD50 at 216.7 ± 10.4 and MIC ≤ 50 μg·mL(-1). Chemometric evaluation (Principal Component Analysis-PCA) showed close interdependence between the ABTS, TPC and TFC methods and allowed to group H. devium samples.

  1. Chemical composition and insecticidal activity of the essential oil from Helichrysum faradifani endemic to Madagascar.

    Benelli, Giovanni; Pavela, Roman; Rakotosaona, Rianasoambolanoro; Randrianarivo, Emmanuel; Nicoletti, Marcello; Maggi, Filippo

    2017-11-03

    Helichrysum faradifani (Asteraceae) is a perennial shrub growing in rocky and sandy places of Madagascar. The plant is used in the Malagasy traditional medicine as a wound-healing agent, disinfectant and for the treatment of syphilis, diarrhea, cough and headache. In the present work, we analysed the chemical composition of the essential oil distilled from the aerial parts of H. faradifani by GC-MS and evaluated its insecticidal activity against 2nd, 3rd and 4th instar larvae of the lymphatic filariasis vector Culex quinquefasciatus by acute toxicity assays. The most sensitive were 2nd instar (LC 50  = 85.7 μL L -1 ) larvae. For the 3rd and 4th instar larvae, the estimated LC 50 were 156.8 and 134.1 μL L -1 , respectively. Monoterpene hydrocarbons (51.6%) were the major fraction of the essential oil, with the bicyclic α-fenchene (35.6%) as the predominant component. Sesquiterpene hydrocarbons (34.0%) were the second major group characterising the oil, with γ-curcumene (17.7%) as the most abundant component.

  2. Constituents of leaves and flowers essential oils of Helichrysum pallasii (Spreng.) Ledeb. growing wild in Lebanon.

    Formisano, Carmen; Mignola, Enrico; Rigano, Daniela; Senatore, Felice; Arnold, Nelly Apostolides; Bruno, Maurizio; Rosselli, Sergio

    2009-02-01

    The chemical compositions of the essential oils obtained from leaves and flowers of Helichrysum pallasii were analyzed by gas chromatography and gas chromatography-mass spectrometry. Among the 102 identified constituents, hexadecanoic acid (16.2%), (Z,Z)-9,12-octadecadienoic acid (6.8%), tetradecanoic acid (2.6%), and (Z)-caryophyllene (4.2%) were the main constituent of the oil from leaves, while in the oil from flowers hexadecanoic acid (14.7%), (Z,Z)-9,12-octadecadienoic acid (14.2%), (Z)-caryophyllene (3.6%), and delta-cadinene (3.1%) predominated. The oils were both characterized by sesquiterpenes (33.4% for leaves and 33.7% for flowers, respectively) and fatty acids and esters (30.3% in leaves and 35% in flowers, respectively). The in vitro activity of the essential oils of the plant against some microorganisms in comparison with chloramphenicol by the broth dilution method was determined. The oils exhibited a weak activity as inhibitors of growth of Staphylococcus epidermidis in vitro (minimum inhibitory concentration = 100 microg/mL).

  3. Identification of anti-HIV active dicaffeoylquinic- and tricaffeoylquinic acids in Helichrysum populifolium by NMR-based metabolomic guided fractionation.

    Heyman, Heino Martin; Senejoux, François; Seibert, Isabell; Klimkait, Thomas; Maharaj, Vinesh Jaichand; Meyer, Jacobus Johannes Marion

    2015-06-01

    South Africa being home to more than 35% of the world's Helichrysum species (c.a. 244) of which many are used in traditional medicine, is seen potentially as a significant resource in the search of new anti-HIV chemical entities. It was established that five of the 30 Helichrysum species selected for this study had significant anti-HIV activity ranging between 12 and 21 μg/mL (IC50) by using an in-house developed DeCIPhR method on a full virus model. Subsequent toxicity tests also revealed little or no toxicity for these active extracts. With the use of NMR-based metabolomics, the search for common chemical characteristics within the plant extract was conducted, which resulted in specific chemical shift areas identified that could be linked to the anti-HIV activity of the extracts. The NMR chemical shifts associated with the activity were identified to be 2.56-3.08 ppm, 5.24-6.28 ppm, 6.44-7.04 ppm and 7.24-8.04 ppm. This activity profile was then used to guide the fractionation process by narrowing down and focusing the fractionation and purification processes to speed up the putative identification of five compounds with anti-HIV activity in the most active species, Helichrysum populifolium. The anti-HIV compounds identified for the first time from H. populifolium were three dicaffeoylquinic acid derivatives, i.e. 3,4-dicaffeoylquinic acid, 3,5-dicaffeoylquinic acid and 4,5-dicaffeoylquinic acid as well as two tricaffeoylquinic acid derivatives i.e. 1,3,5-tricaffeoylquinic acid and either 5-malonyl-1,3,4-tricaffeoylquinic or 3-malonyl-1,4,5-tricaffeoylquinic acid, with the latter being identified for the first time in the genus. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Separation of phytochemicals from Helichrysum italicum: An analysis of different isolation techniques and biological activity of prepared extracts.

    Maksimovic, Svetolik; Tadic, Vanja; Skala, Dejan; Zizovic, Irena

    2017-06-01

    Helichrysum italicum presents a valuable source of natural bioactive compounds. In this work, a literature review of terpenes, phenolic compounds, and other less common phytochemicals from H. italicum with regard to application of different separation methods is presented. Data including extraction/separation methods and experimental conditions applied, obtained yields, number of identified compounds, content of different compound groups, and analytical techniques applied are shown as corresponding tables. Numerous biological activities of both isolates and individual compounds are emphasized. In addition, the data reported are discussed, and the directions for further investigations are proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Chemical composition and in vitro antimicrobial activity of the essential oils of two Helichrysum species from Tanzania.

    Bougatsos, Christos; Ngassapa, Olipa; Runyoro, Deborah K B; Chinou, Ioanna B

    2004-01-01

    The chemical composition of the essential oils obtained from the aerial parts of Helichrysum cymosum and H. fulgidum, from Tanzania, were analyzed by GC and GC/MS. A total of sixty-five compounds, representing 92.4% and 88.2% of the two oils, respectively, were identified. trans-Caryophyllene, caryophyllene oxide, beta-pinene, p-cymene, spathulenol and beta-bourbonene were found to be the main components. Furthermore, the oils were tested against six gram (+/-) bacteria and three pathogenic fungi. It was found that the oil of H. fulgidum exhibited significant antimicrobial activity, while the oil of H. cymosum was not active at all.

  6. Full range ZVS DC-DC converter

    Upadhyay, Rinki; Badapanda, M.K.; Hannurkar, P.R.

    2011-01-01

    A 500 V, 24 Amp DC-DC converter with digital signal processor (DSP) based control and protection has been designed, fabricated and tested. Its power circuit consists of IGBT based single phase inverter bridge, ferrite transformer and diode rectifier. All IGBTs in the inverter bridge are operated in zero voltage switching (ZVS) mode to minimize switching losses thereby increasing the efficiency of the converter significantly. The efficiency of this converter is measured to be greater than 97% at full load. In a conventional full bridge inverter, typically ZVS is achieved under full load condition while at light load ZVS is lost. An auxiliary LC circuit has been intentionally incorporated in this converter to achieve ZVS even at light loaded conditions. Detailed simulation of the converter circuit is carried out and crucial waveforms have been presented in this paper. Microchip make dsPIC30F2020 DSP is employed to provide phase shifted PWMs to IGBTs in the inverter bridge. All the crucial parameters are also monitored by this DSP and in case of any unfavorable conditions, the converter is tripped off. Suitable experiments were carried out in this DC-DC converter under different loaded conditions and a close match between the simulated and experimental results were obtained. Such DC-DC converters can be connected in series or parallel for the development of solid state modular power supplies for various applications. (author)

  7. Biochemical characterization of Helichrysum italicum (Roth) G.Don subsp. italicum (Asteraceae) from Montenegro: phytochemical screening, chemotaxonomy, and antioxidant properties.

    Kladar, Nebojša V; Anačkov, Goran T; Rat, Milica M; Srđenović, Branislava U; Grujić, Nevena N; Šefer, Emilia I; Božin, Biljana N

    2015-03-01

    The chemical composition and antioxidant properties of the essential oil and EtOH extract of immortelle (Helichrysum italicum (Roth) G.Don subsp. italicum, Asteraceae) collected in Montenegro were evaluated. The essential oil was characterized by GC/MS analysis, and the content of total phenolics and flavonoids in the EtOH extract was determined using the FolinCiocalteu reagent. The free-radical-scavenging capacity (RSC) of both the essential oil and the EtOH extract was assessed with the 2,2-diphenyl-1-pycrylhydrazyl (DPPH) method. Moreover, the inhibition of hydroxyl radical ((.) OH) generation by the EtOH extract of immortelle was evaluated for the first time here. Neryl acetate (28.2%) and γ-curcumene (18.8%) were the main compounds in the essential oil, followed by neryl propionate (9.1%) and ar-curcumene (8.3%). The chemical composition of the oils of the examined and additional 16 selected Helichrysum italicum taxa described in literature were compared using principal component (PCA) and cluster (CA) analyses. The results of the statistical analyses implied the occurrence of at least four different main and three subchemotypes of essential oils. Considering the antioxidant properties, the EtOH extract of immortelle exhibited similar potential as propyl gallate and quercetin, while the essential oil exhibited relatively weak DPPH(.) -scavenging capacity. Copyright © 2015 Verlag Helvetica Chimica Acta AG, Zürich.

  8. Re-evaluation of the Helichrysum italicum complex (Compositae: Gnaphalieae: A new species from Majorca (Balearic Islands

    S. Herrando-Moraira

    2016-09-01

    Full Text Available Helichrysum italicum is a widely distributed species in the Mediterranean Basin, which has received controversial taxonomic treatments at infraspecific level owing to its morphological variability. In this paper we perform a detailed multivariate analysis of morphological characters using an exhaustive sampling of H. italicum. Integrating previously published molecular, chorological and newly obtained morphological data, a revised taxonomic treatment for the whole H. italicum complex is provided. On the one hand, the results obtained suggest that the Majorcan mountain populations of H. italicum subsp. microphyllum need to be considered an independent species, newly described here as Helichrysum massanellanum. On the other hand, H. italicum subspecies are recircumscribed. A new combination is proposed, H. italicum subsp. tyrrhenicum, a taxon that comprises populations from Corsica, Sardinia, Majorca coastline and Dragonera islet, whereas subsp. microphyllum is restricted to the island of Crete. With those substantial classification modifications, a complete new taxonomic treatment is presented for this group, including an identification key, synonyms, morphological descriptions, distribution areas and habitat characterization.

  9. Acylphloroglucinol Derivatives from the South African Helichrysum niveum and Their Biological Activities

    Olugbenga K. Popoola

    2015-09-01

    Full Text Available Phytochemical investigation of aerial parts of Helichrysum niveum (H. niveum using different chromatographic methods including semi-preparative HPLC afforded three new (1–3 and six known (4–10 acylphloroglucinols alongside a known dialcohol triterpene (11. The structures of the isolated compounds were characterized accordingly as 1-benzoyl-3 (3-methylbut-2-enylacetate-phloroglucinol (helinivene A, 1, 1-benzoyl-3 (2S-hydroxyl-3-methylbut-3-enyl-phloroglucinol (helinivene B, 2, 8-(2-methylpropanone-3S,5,7-trihydroxyl-2,2-dimethoxychromane (helinivene C, 3, 1-(2-methylbutanone-4-O-prenyl-phloroglucinol (4, 1-(2-methylpropanone-4-O-prennyl-phloroglucinol (5, 1-(butanone-3-prenyl-phloroglucinol (6, 1-(2-methylbutanone-3-prenyl-phloroglucinol (7, 1-butanone-3-(3-methylbut-2-enylacetate-phloroglucinol (8, 1-(2-methylpropanone-3-prenylphloroglucinol (9, caespitate (10, and 3β-24-dihydroxyterexer-14-ene (11. Excellent total antioxidant capacities were demonstrated by helinivenes A and B (1 and 2 when measured as oxygen radicals absorbance capacity (ORAC, ferric-ion reducing antioxidant power (FRAP, trolox equivalent absorbance capacity (TEAC and including the inhibition of Fe2+-induced lipid peroxidation (IC50 = 5.12 ± 0.90; 3.55 ± 1.92 µg/mL, while anti-tyrosinase activity at IC50 = 35.63 ± 4.67 and 26.72 ± 5.05 µg/mL were also observed for 1 and 2, respectively. This is the first chemical and in vitro biological study on H. niveum. These findings underpin new perspectives for the exploitation of these natural phenolic compounds in applications such as in the natural cosmeceutical and pharmaceutical sectors.

  10. Acylphloroglucinol Derivatives from the South African Helichrysum niveum and Their Biological Activities.

    Popoola, Olugbenga K; Marnewick, Jeanine L; Rautenbach, Fanie; Iwuoha, Emmanuel I; Hussein, Ahmed A

    2015-09-18

    Phytochemical investigation of aerial parts of Helichrysum niveum (H. niveum) using different chromatographic methods including semi-preparative HPLC afforded three new (1-3) and six known (4-10) acylphloroglucinols alongside a known dialcohol triterpene (11). The structures of the isolated compounds were characterized accordingly as 1-benzoyl-3 (3-methylbut-2-enylacetate)-phloroglucinol (helinivene A, 1), 1-benzoyl-3 (2S-hydroxyl-3-methylbut-3-enyl)-phloroglucinol (helinivene B, 2), 8-(2-methylpropanone)-3S,5,7-trihydroxyl-2,2-dimethoxychromane (helinivene C, 3), 1-(2-methylbutanone)-4-O-prenyl-phloroglucinol (4), 1-(2-methylpropanone)-4-O-prennyl-phloroglucinol (5), 1-(butanone)-3-prenyl-phloroglucinol (6), 1-(2-methylbutanone)-3-prenyl-phloroglucinol (7), 1-butanone-3-(3-methylbut-2-enylacetate)-phloroglucinol (8), 1-(2-methylpropanone)-3-prenylphloroglucinol (9), caespitate (10), and 3β-24-dihydroxyterexer-14-ene (11). Excellent total antioxidant capacities were demonstrated by helinivenes A and B (1 and 2) when measured as oxygen radicals absorbance capacity (ORAC), ferric-ion reducing antioxidant power (FRAP), trolox equivalent absorbance capacity (TEAC) and including the inhibition of Fe(2+)-induced lipid peroxidation (IC50 = 5.12 ± 0.90; 3.55 ± 1.92) µg/mL, while anti-tyrosinase activity at IC50 = 35.63 ± 4.67 and 26.72 ± 5.05 µg/mL were also observed for 1 and 2, respectively. This is the first chemical and in vitro biological study on H. niveum. These findings underpin new perspectives for the exploitation of these natural phenolic compounds in applications such as in the natural cosmeceutical and pharmaceutical sectors.

  11. Gradient of structural traits drives hygroscopic movements of scarious bracts surrounding Helichrysum bracteatum capitulum.

    Borowska-Wykret, Dorota; Rypien, Aleksandra; Dulski, Mateusz; Grelowski, Michal; Wrzalik, Roman; Kwiatkowska, Dorota

    2017-06-01

    The capitulum of Helichrysum bracteatum is surrounded by scarious involucral bracts that perform hygroscopic movements leading to bract bending toward or away from the capitulum, depending on cell wall water status. The present investigation aimed at explaining the mechanism of these movements. Surface strain and bract shape changes accompanying the movements were quantified using the replica method. Dissection experiments were used to assess the contribution of different tissues in bract deformation. Cell wall structure and composition were examined with the aid of light and electron microscopy as well as confocal Raman spectroscopy. At the bract hinge (organ actuator) longitudinal strains at opposite surfaces differ profoundly. This results in changes of hinge curvature that drive passive displacement of distal bract portions. The distal portions in turn undergo nearly uniform strain on both surfaces and also minute shape changes. The hinge is built of sclerenchyma-like abaxial tissue, parenchyma and adaxial epidermis with thickened outer walls. Cell wall composition is rather uniform but tissue fraction occupied by cell walls, cell wall thickness, compactness and cellulose microfibril orientation change gradually from abaxial to adaxial hinge surface. Dissection experiments show that the presence of part of the hinge tissues is enough for movements. Differential strain at the hinge is due to adaxial-abaxial gradient in structural traits of hinge tissues and cell walls. Thus, the bract hinge of H. bracteatum is a structure comprising gradually changing tissues, from highly resisting to highly active, rather than a bi-layered structure with distinct active and resistance parts, often ascribed for hygroscopically moving organs. © The Author 2017. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  12. High voltage dc cables

    Bjustrom, B

    1965-12-01

    How stress distribution in dc cables varies with temperature and stress level, influence of polarity reversals and space charges, and different types of overvoltage to which dc cable may be subjected are discussed. Design problems, especially as related to corrosion protection and to mechanical stress caused by wire armoring during manufacturing and laying, accessories and work done on test methods, and the possibility of designing 400 to 600 kV dc cables for transmitting 2000 to 4000 MW are described.

  13. Family of multiport bidirectional DC-DC converters

    Tao, H.; Kotsopoulos, A.; Duarte, J.L.; Hendrix, M.A.M.

    2006-01-01

    Multiport DC-DC converters are of potential interest in applications such as generation systems utilising multiple sustainable energy sources. A family of multiport bidirectional DC-DC converters derived from a general topology is presented. The topology shows a combination of DC-link and magnetic

  14. Programmable dc motor controller

    Hopwood, J. E.

    1982-11-01

    A portable programmable dc motor controller, with features not available on commercial instruments was developed for controlling fixtures during welding processes. The controller can be used to drive any dc motor having tachometer feedback and motor requirements not exceeding 30 volts, 3 amperes. Among the controller's features are delayed start time, upslope time, speed, and downslope time.

  15. Multilevel DC link inverter

    Su, Gui-Jia

    2003-06-10

    A multilevel DC link inverter and method for improving torque response and current regulation in permanent magnet motors and switched reluctance motors having a low inductance includes a plurality of voltage controlled cells connected in series for applying a resulting dc voltage comprised of one or more incremental dc voltages. The cells are provided with switches for increasing the resulting applied dc voltage as speed and back EMF increase, while limiting the voltage that is applied to the commutation switches to perform PWM or dc voltage stepping functions, so as to limit current ripple in the stator windings below an acceptable level, typically 5%. Several embodiments are disclosed including inverters using IGBT's, inverters using thyristors. All of the inverters are operable in both motoring and regenerating modes.

  16. Cardiovascular effects of Helichrysum ceres S Moore [Asteraceae] ethanolic leaf extract in some experimental animal paradigms.

    Musabayane, Cephas T; Kamadyaapa, Dave R; Gondwe, Mavuto; Moodley, Kogi; Ojewole, John A O

    2008-01-01

    The aim of this study was to examine some in vivo and in vitro cardiovascular effects of Helichrysum ceres leaf ethanolic extract (HCE) in experimental animal paradigms. The acute effects of HCE on blood pressure were studied in anaesthetised normotensive male Wistar rats challenged with intravenous hypotonic saline infusion after a 3.5-hour equilibration for four hours of one-hour control, 1.5-hour treatment and 1.5-hour recovery periods. HCE was added to the infusate during the treatment period. Sub-chronic hypotensive effects of HCE were examined in weanling Dahl saltsensitive (DSS) genetically hypertensive rats, which progressively develop hypertension with age, treated with HCE (80 mg/kg) every third consecutive day for seven weeks. Isolated atrial muscle strips, portal veins and descending thoracic aortic rings of healthy normotensive Wistar rats were used to investigate the vascular effects of HCE. Acute HCE administration caused a significant (p < 0.05) fall in blood pressure in the normotensive anaesthetised Wistar rats. DSS hypertensive rats treated with HCE displayed low arterial blood pressure and heart rate values from weeks five to seven. HCE produced concentrationdependent negative inotropic and chronotropic effects on rat isolated electrically driven left, and spontaneously beating right atrial muscle preparations, respectively. HCE also evoked concentration-dependent relaxation responses of endothelium-intact aortic rings and portal veins isolated from healthy normotensive Wistar rats. The vasorelaxant effects of HCE in intact aortic rings were significantly reduced, but not completely abolished by adding endothelial- derived factor (EDRF) inhibitor, L-NAME, suggesting that the vasorelaxant effect of the extract is mediated via EDRF-dependent and independent mechanisms. The results of the study suggest that the hypotensive action of HCE is elicited, in part, directly by decreasing myocardial contractile performance and total peripheral vascular

  17. Antifungal activity of Helichrysum italicum (Roth G. Don (Asteraceae essential oil against fungi isolated from cultural heritage objects

    Stupar Miloš

    2014-01-01

    Full Text Available There is considerable interest in the use of essential oils as alternative methods to control micromycetes from cultural heritage objects. We investigated the chemical composition and antifungal activity of the essential oil of Helichrysum italicum. The main components of the oil were γ-curcumene (22.45%, α-pinene (15.91 % and neryl acetate (7.85 %. H. italicum essential oil showed moderate antifungal activity against fungi isolated from cultural heritage objects. The most susceptible fungi to oil treatment were Epicoccum nigrum and Penicillium sp., while the most resistant was Trichoderma viride. The H. italicum essential oil showed demelanizing activity against Aspergillus niger. [Projekat Ministarstva nauke Republike Srbije, br. 173032

  18. Influence of environmental factors on composition of volatile constituents and biological activity of Helichrysum italicum (Roth) Don (Asteraceae).

    Tundis, R; Statti, G A; Conforti, F; Bianchi, A; Agrimonti, C; Sacchetti, G; Muzzoli, M; Ballero, M; Menichini, F; Poli, F

    2005-06-01

    The biovariability of Helichrysum italicum (Roth) Don grown wild in Calabria and Sardinia (Italy) was reported. This species has been characterized through the detection, isolation and quantitative evaluation of chemical markers (alpha-terpinolene, trans-cariophyllene and neryl acetate) by GC and GC-MS. Antioxidant activity of the methanolic H. italicum extracts using DPPH and beta-carotene bleaching test showed that the Calabrian samples were more active than those from Sardinia. The antibacterial activity of all extracts evidenced the best performance on the Gram positive bacteria particularly on Micrococcus luteus. Moreover, antifungal activity of all extracts was also tested evidencing important results particularly on the phytopathogene fungus Pythium ultimum. In general, as regards the antifungal activity, the extracts from Sardinia were more active than those from Calabria. The phytochemical analysis and the biological activity data suggested a possible use of these plant matrices in alimentary, cosmetic and pharmaceutical fields.

  19. Assessment of extracts of Helichrysum arenarium, Crataegus monogyna, Sambucus nigra in photoprotective UVA and UVB; photostability in cosmetic emulsions.

    Jarzycka, Anna; Lewińska, Agnieszka; Gancarz, Roman; Wilk, Kazimiera A

    2013-11-05

    The aim of our study was to investigate the photoprotective activity and photostability efficacy of sunscreen formulations containing Helichrysum arenarium, Sambucus nigra, Crataegus monogyna extracts and their combination. UV transmission of the emulsion films was performed by using diffuse transmittance measurements coupling to an integrating sphere. In vitro photoprotection and photostability efficacy were evaluated according to the following parameters: sun protection factor (SPF), UVA protection factor (PF-UVA), UVA/UVB ratio and critical wavelength (λc) before and after UV irradiation. The results obtained show that the formulations containing polyphenols fulfill the official requirements for sunscreen products due to their broad spectrum of UV protection combined with their high photostability and remarkable antioxidant properties. Therefore H. arenarium, S. nigra, C. monogyna extracts represent useful additives for cosmetic formulation. Copyright © 2013 Elsevier B.V. All rights reserved.

  20. Spectroscopic identification and anti-biofilm properties of polar metabolites from the medicinal plant Helichrysum italicum against Pseudomonas aeruginosa.

    D'Abrosca, Brigida; Buommino, Elisabetta; D'Angelo, Grazia; Coretti, Lorena; Scognamiglio, Monica; Severino, Valeria; Pacifico, Severina; Donnarumma, Giovanna; Fiorentino, Antonio

    2013-11-15

    Two new acylated styrylpyrones, one 5-methoxy-1(3H)-isobenzofuranone glucoside and a hydroxymethyl-orcinol derivative, along with sixteen known aromatic metabolites, including lignans, quinic acid derivatives low-molecular weight phenol glucosides, have been isolated from the methanol extract of Helichrysum italicum, a medicinal plant typical of the Mediterranean vegetation. The structures of these compounds have been elucidated on the basis of extensive 2D-NMR spectroscopic analyses, including COSY, TOCSY, HSQC, CIGAR-HMBC, H2BC and HSQC-TOCSY, along with Q-TOF HRMS(2) analysis. Selected compounds were evaluated for their anti-biofilm properties against Pseudomonas aeruginosa. Copyright © 2013. Published by Elsevier Ltd.

  1. Bidirectional dc-to-dc Power Converter

    Griesbach, C. R.

    1986-01-01

    Solid-state, series-resonant converter uses high-voltage thyristors. Converter used either to convert high-voltage, low-current dc power to lowvoltage, high current power or reverse. Taking advantage of newly-available high-voltage thyristors to provide better reliability and efficiency than traditional converters that use vacuum tubes as power switches. New converter essentially maintenance free and provides greatly increased mean time between failures. Attractive in industrial applications whether or not bidirectional capability is required.

  2. A DC Transformer

    National Aeronautics and Space Administration — The goal of the project was to demonstrate a true direct current (DC) transformer, a new electro-mechanical component with potentially high power applications; in...

  3. Analysis of phenolic compounds from different morphological parts of Helichrysum devium by liquid chromatography with on-line UV and electrospray ionization mass spectrometric detection.

    Gouveia, Sandra C; Castilho, Paula C

    2009-12-01

    A simple and rapid method has been used for the screening and identification of the main phenolic compounds from Helichrysum devium using high-performance liquid chromatography with on-line UV and electrospray ionization mass spectrometric detection (LC-DAD/ESI-MS(n)). The total aerial parts and different morphological parts of the plant, namely leaves, flowers and stems, were analyzed separately. A total of 34 compounds present in the methanolic extract from Helichrysum devium were identified or tentatively characterized based on their UV and mass spectra and retention times. Three of these compounds were positively identified by comparison with reference standards. The phenolic compounds included derivatives of quinic acid, O-glycosylated flavonoids, a caffeic acid derivative and a protocatechuic acid derivative. The characteristic loss of 206 Da from malonylcaffeoyl quinic acid was used to confirm the malonyl linkage to the caffeoyl group. This contribution presents one of the first reports on the analysis of phenolic compounds from Helichrysum devium using LC-DAD/ESI-MS(n) and highlights the prominence of quinic acid derivatives as the main group of phenolic compounds present in these extracts. We also provide evidence that the methanolic extract from the flowers was significantly more complex when compared to that of other morphological parts. Copyright 2009 John Wiley & Sons, Ltd.

  4. Three new DC-to-DC Single-Switch Converters

    Barry W. Williams

    2017-06-01

    Full Text Available This paper presents a new family of three previously unidentified dc-to-dc converters, buck, boost, and buck-boost voltage-transfer-function topologies, which offer advantageous transformer coupling features and low capacitor dc voltage stressing. The three single-switch, single-diode, converters offer the same features as basic dc-to-dc converters, such as the buck function with continuous output current and the boost function with continuous input current. Converter time-domain simulations and experimental results (including transformer coupling support and extol the dc-to-dc converter concepts and analysis presented.

  5. Three-port DC-DC converter with new integrated transformer for DC Distribution Systems

    Ouyang, Ziwei; Andersen, Michael A. E.

    2014-01-01

    A new integrated transformer for three-port dc-dc converter is proposed to overcome the power coupling effect existed in some known multiple inputs dc-dc converters. Orthogonal primary windings arrangement and in series connection of diagonal secondary Windings enables a fully power decoupling...

  6. 75 FR 23571 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

    2010-05-04

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10... amends Sec. 39.13 by adding the following new AD: 2010-09-12 McDonnell Douglas Corporation: Amendment 39... to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A...

  7. Design and Testing of Boost Type DC/DC Converter for DC Motor Control Applications

    Samman, Faizal Arya; Akil, Yusri Syam; Noor, Nirwan A.

    2017-01-01

    in The Proceeding of The 2nd International Symposium on Smart Material and Mechatronics 2015 This paper presents the design and testing of a boost type DC/DC converter circuit, which can be used for DC motor control applications. The Boost converter is designed using DC chopper and DC chopper cascade configurations. The experimental setup was made by connecting the boost converter circuit with four types of DC motor, i.e. self-excited DC motor shunt, series, compound and separately exci...

  8. Control of improved full-bridge three-level DC/DC converter for wind turbines in a DC grid

    Deng, Fujin; Chen, Zhe

    2013-01-01

    transformer in the IFBTL dc/dc converter. A modulation strategy, including two operation modes, is proposed for the IFBTL dc/dc converter. Then, a voltage balancing control strategy is proposed for the IFBTL dc/dc converter. Furthermore, the control of the wind turbine based on the IFBTL dc/dc converter......This paper presents an improved full-bridge three-level (IFBTL) dc/dc converter for a wind turbine in a dc grid by inserting a passive filter into the dc/dc converter to improve the performance of the converter. The passive filter can effectively reduce the voltage stress of the medium frequency...

  9. Overview of Multi-DC-Bus Solutions for DC Microgrids

    Ricchiuto, D.; Mastromauro, R.A.; Liserre, Marco

    2013-01-01

    DC Microgrids have recently received a lot of attention in the last years due to high penetration of renewable energy sources as well as distributed energy storage systems. In the future DC microgrids could be preferable respect to AC microgrids in terms of redundancy since multi-DC-Bus solutions...... could provide a continuative power supply to the loads. An overview of Multi-DC-Bus solutions is presented in this paper. The performances are compared on the basis of possible DC microgrid configurations, redundancy, different DC voltage levels....

  10. Multi Bus DC-DC Converter in Electric Hybrid Vehicles

    Krithika, V.; Subramaniam, C.; Sridharan, R.; Geetha, A.

    2018-04-01

    This paper is cotncerned with the design, simulation and fabrication of the prototype of a Multi bus DC- DC converter operating from 42V DC and delivering 14V DC and 260V DC. As a result, three DC buses are interconnected through a single power electronic circuitry. Such a requirement is energized in the development of a hybrid electric automobile which uses the technology of fuel cell. This is implemented by using a Bidirectional DC-DC converter configuration which is ideally suitable for multiple outputs with mutual electrical isolation. For the sake of reduced size and cost of step-up transformer, selection of a high frequency switching cycle at 10 KHz was done.

  11. dc Arc Fault Effect on Hybrid ac/dc Microgrid

    Fatima, Zahra

    The advent of distributed energy resources (DER) and reliability and stability problems of the conventional grid system has given rise to the wide spread deployment of microgrids. Microgrids provide many advantages by incorporating renewable energy sources and increasing the reliability of the grid by isolating from the main grid in case of an outage. AC microgrids have been installed all over the world, but dc microgrids have been gaining interest due to the advantages they provide over ac microgrids. However the entire power network backbone is still ac and dc microgrids require expensive converters to connect to the ac power network. As a result hybrid ac/dc microgrids are gaining more attention as it combines the advantages of both ac and dc microgrids such as direct integration of ac and dc systems with minimum number of conversions which increases the efficiency by reducing energy losses. Although dc electric systems offer many advantages such as no synchronization and no reactive power, successful implementation of dc systems requires appropriate protection strategies. One unique protection challenge brought by the dc systems is dc arc faults. A dc arc fault is generated when there is a gap in the conductor due to insulation degradation and current is used to bridge the gap, resulting in an arc with very high temperature. Such a fault if it goes undetected and is not extinguished can cause damage to the entire system and cause fires. The purpose of the research is to study the effect of the dc arc fault at different locations in the hybrid ac/dc microgrid and provide insight on the reliability of the grid components when it is impacted by arc faults at various locations in the grid. The impact of dc arc fault at different locations on the performance of the PV array, wind generation, and constant power loads (CPL) interfaced with dc/dc converters is studied. MATLAB/Simulink is used to model the hybrid ac/dc microgrid and arc fault.

  12. Early Oscillation Detection for DC/DC Converter Fault Diagnosis

    Wang, Bright L.

    2011-01-01

    The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

  13. In vitro Investigation of Hydro-alcoholic Extract of Helichrysum leucocephalum on the Inhibition of Streptococcus Mutans Growth

    Motamedifar M

    2017-12-01

    Full Text Available Statement of Problem: Indiscriminate use of antibacterial agents increases the antibiotic resistance, which consequently necessitates seeking alternatives such as herbal remedies. Objectives: The aim of this study was to evaluate the antimicrobial effect of hydroalcoholic extract of Helichrysum leucocephalum (H.leucocephalum on Streptococcus mutans (S. mutans growth as a major cause of dental caries. Materials and Methods: In this study, hydroalcoholic extract of H. leucocephalum was prepared. The antibacterial effects, minimal inhibitory concentration (MIC, and minimal bactericidal concentration (MBC of hydroalcoholic extract of H. leucocephalum and penicillin were assessed. Agar well diffusion method and micro broth dilution assay were used on bacterial suspension adjusted to a 0.5 McFarland standard (equivalent to 1.5×108 CFU/mL.Each test was repeated four times to minimize lab errors. Results: In this study, the inhibitory zone of hydroalcoholic extract of H.leucocephalum in concentration of 100 mg/mL was 34±0.1 mm and for penicillin was 10 mm. The MIC and MBC of H.leucocephalum hydroalcoholic extract were 5.6±6.25, 21.6±6.25 mg/mL, respectively. Conclusions: Hydroalcoholic extract of H. leucocephalum have antibacterial effect on S.mutans at a concentration of 12.5mg/mL, indicating possible application of this extract in prevention of dental caries; however, future researches are necessary.

  14. Phytochemical Analysis, Antioxidant and Antimicrobial Activities of Helichrysum arenarium (L.) Moench. and Antennaria dioica (L.) Gaertn. Flowers.

    Babotă, Mihai; Mocan, Andrei; Vlase, Laurian; Crișan, Ovidiu; Ielciu, Irina; Gheldiu, Ana-Maria; Vodnar, Dan Cristian; Crișan, Gianina; Păltinean, Ramona

    2018-02-13

    Antennaria dioica (L.) Gaertn. and Helichrysum arenarium (L.) Moench. are two species of the Asteraceae family, known in Romanian traditional medicine for their diuretic, choleretic, and anti-inflammatory properties. The aim of the present study was to evaluate the phenolic and sterolic composition of flowers from the two species and to assess their antioxidant, antibacterial and antifungal properties. LC-MS analyses were performed on methanolic, ethanolic and 70% v/v ethanolic extracts, before and after acid hydrolysis, and revealed high amounts of polyphenols. Chlorogenic acid was found as the main compound for the flowers of A. dioica (502.70 ± 25.11 mg/100 g d.w.), while quercitrin was dominant in H. arenarium (424.28 ± 21.21 mg/100 g d.w.) in 70% v / v ethanolic extracts before hydrolysis. Antioxidant capacity assays showed an important antioxidant potential, which can be correlated with the determined polyphenolic compounds, showing the 70% v / v ethanolic extracts of the two species as being the most effective antioxidant samples for the DPPH assay. Antibacterial and antifungal assays confirm a modest biological potential for the same extract of both species. Results obtained in the present study bring important data and offer scientific evidence on the chemical composition and on the biological activities of the flowers belonging to the two species.

  15. Phytochemical Analysis, Antioxidant and Antimicrobial Activities of Helichrysum arenarium (L. Moench. and Antennaria dioica (L. Gaertn. Flowers

    Mihai Babotă

    2018-02-01

    Full Text Available Antennaria dioica (L. Gaertn. and Helichrysum arenarium (L. Moench. are two species of the Asteraceae family, known in Romanian traditional medicine for their diuretic, choleretic, and anti-inflammatory properties. The aim of the present study was to evaluate the phenolic and sterolic composition of flowers from the two species and to assess their antioxidant, antibacterial and antifungal properties. LC-MS analyses were performed on methanolic, ethanolic and 70% v/v ethanolic extracts, before and after acid hydrolysis, and revealed high amounts of polyphenols. Chlorogenic acid was found as the main compound for the flowers of A. dioica (502.70 ± 25.11 mg/100 g d.w., while quercitrin was dominant in H. arenarium (424.28 ± 21.21 mg/100 g d.w. in 70% v/v ethanolic extracts before hydrolysis. Antioxidant capacity assays showed an important antioxidant potential, which can be correlated with the determined polyphenolic compounds, showing the 70% v/v ethanolic extracts of the two species as being the most effective antioxidant samples for the DPPH assay. Antibacterial and antifungal assays confirm a modest biological potential for the same extract of both species. Results obtained in the present study bring important data and offer scientific evidence on the chemical composition and on the biological activities of the flowers belonging to the two species.

  16. Antioxidant activity profiling by spectrophotometric methods of aqueous methanolic extracts of Helichrysum stoechas subsp. rupestre and Phagnalon saxatile subsp. saxatile.

    Haddouchi, Farah; Chaouche, Tarik Mohammed; Ksouri, Riadh; Medini, Faten; Sekkal, Fatima Zohra; Benmansour, Abdelhafid

    2014-06-01

    The aqueous methanolic extracts of two plants from Algeria, Helichrysum stoechas subsp. rupestre and Phagnalon saxatile subsp. saxatile, were investigated for their antioxidant activity. Total phenolics, flavonoids, and tannins were determined by spectrophotometric techniques. In vitro antioxidant and radical scavenging profiling was determined by spectrophotometric methods, through: Total antioxidant capacity, and radical scavenging effects by the DPPH and ABTS methods, reducing and chelating power, and blanching inhibition of the β-carotene. All of the extracts showed interesting antioxidant and radical scavenging activity. The highest contents in phenolics, tannins, and the highest total antioxidant capacity as gallic acid equivalents of 97.5 ± 0.33 mg GAE/g DW was obtained for the flowers of H. stoechas subsp. rupestre extract in the phosphomolybdenum assay. An extract of the leafy stems of P. saxatile subsp. saxatile revealed the highest content of flavonoids, and the highest antioxidant activity by the radical scavenging and β-carotene assays when compared with standards. The best activity was by the scavenging radical DPPH with an IC50 value of 5.65 ± 0.10 μg·mL(-1). The studied medicinal plants could provide scientific evidence for some traditional uses in the treatment of diseases related to the production of reactive oxygen species (ROS) and oxidative stress. Copyright © 2014 China Pharmaceutical University. Published by Elsevier B.V. All rights reserved.

  17. A study of antidiabetic and antioxidant effects of Helichrysum graveolens capitulums in streptozotocin-induced diabetic rats.

    Aslan, Mustafa; Orhan, Didem Deliorman; Orhan, Nilüfer; Sezik, Ekrem; Yeşilada, Erdem

    2007-06-01

    Helichrysum graveolens (Bieb.) Sweet (Asteraceae) grows widely in Turkey. Capitulums of H. graveolens are used in the treatment of many diseases such as jaundice and wound healing and as a diuretic in the rural areas of Anatolia. The decoction from the capitulums of the plant is consumed for the symptoms of diabetes mellitus in folk medicine. In the present study, the hypoglycemic, antihyperglycemic, and antioxidant potentials of water and ethanol extracts of H. graveolens were evaluated by using in vivo methods in normal and streptozotocin-induced diabetic rats. Blood glucose levels of animals were measured by the glucose oxidase method. The antioxidant activity of these extracts was also studied in liver, kidney, and heart tissues. In order to determine antioxidant activity, tissue malondialdehyde and reduced glutathione levels were measured by using spectrophotometric methods. The experimental data obtained from water and ethanol extracts of capitulums confirmed the folkloric utilization. In order to discuss the role of polyphenolic components in the relevant activity, total phenol and flavonoid contents of each extract were also determined using the Folin-Ciocalteu reagent, and a positive correlation was observed.

  18. Arzanol, an anti-inflammatory and anti-HIV-1 phloroglucinol alpha-Pyrone from Helichrysum italicum ssp. microphyllum.

    Appendino, Giovanni; Ottino, Michela; Marquez, Nieves; Bianchi, Federica; Giana, Anna; Ballero, Mauro; Sterner, Olov; Fiebich, Bernd L; Munoz, Eduardo

    2007-04-01

    An acetone extract of Helichrysum italicum ssp. microphyllum afforded the phloroglucinol alpha-pyrone arzanol (1a) as a potent NF-kappaB inhibitor. Arzanol is identical with homoarenol (2a), whose structure should be revised. The phloroglucinol-type structure of arzanol and the 1,2,4-trihydroxyphenyl-type structure of the base-induced fragmentation product of homoarenol could be reconciled in light of a retro-Fries-type fragmentation that triggers a change of the hydroxylation pattern of the aromatic moiety. On the basis of these findings, the structure of arenol, the major constituent of the clinically useful antibiotic arenarin, should be revised from 2b to 1b, solving a long-standing puzzle over its biogenetic derivation. An alpha-pyrone (micropyrone, 7), the monoterpene rac-E-omega-oleoyloxylinalol (10), four known tremetones (9a-d), and the dimeric pyrone helipyrone (8) were also obtained. Arzanol inhibited HIV-1 replication in T cells and the release of pro-inflammatory cytokines in LPS-stimulated primary monocytes, qualifying as a novel plant-derived anti-inflammatory and antiviral chemotype worth further investigation.

  19. Cancer-suppressive potential of extracts of endemic plant Helichrysum zivojinii: effects on cell migration, invasion and angiogenesis.

    Matić, Ivana Z; Aljancić, Ivana; Vajs, Vlatka; Jadranin, Milka; Gligorijević, Nevenka; Milosavljević, Slobodan; Juranić, Zorica D

    2013-09-01

    Helichrysum zivojinii Cernjavski & Soska is an endemic plant species that grows in the National Park Galicica in Macedonia. Five extracts were isolated as fractions from the aerial parts of the plant: a n-hexane extract (1), a dichloromethane extract (2), an ethyl-acetate extract (3), a n-butanol extract (4) and a methanol extract (5). A dose-dependent cytotoxic activity of the extracts on MDA-MB-231 and EA.hy926 cells was observed. Extracts exhibited more pronounced cytotoxic actions on MDA-MB-231 cells than on EA.hy926 cells. The n-hexane extract (1), at a non-toxic concentration, exhibited an inhibitory effect on the migration as well the invasiveness of MDA-MB-231 cells. The dichloromethane extract (2), at a non-toxic concentration, demonstrated inhibition of MDA-MB-231 cells invasion. Each of the five extracts applied at non-toxic concentrations inhibited migration of EA.hy926 cells. The prominent inhibitory effect of the n-hexane extract on EA.hy926 cells migration was associated with a notable anti-angiogenic action of this extract. The other four tested extracts demonstrated mild anti-angiogenic activity. Our data highlight the prominent anticancer potential of n-hexane (1) and dichloromethane (2) extracts, which could be attributed to their very pronounced and selective cytotoxic activities as well as their anti-invasive and anti-angiogenic properties.

  20. Essential-oil composition of Helichrysum italicum (ROTH) G.DON ssp. italicum from Elba Island (Tuscany, Italy).

    Leonardi, Michele; Ambryszewska, Katarzyna E; Melai, Bernardo; Flamini, Guido; Cioni, Pier Luigi; Parri, Federico; Pistelli, Luisa

    2013-03-01

    The composition of 21 essential-oil samples isolated from Helichrysum italicum collected in seven locations of Elba Island (Tuscany, Italy), characterized by different soil types, during three different periods (January, May, and October 2010) was determined by GC-FID and GC/EI-MS analyses. In total, 115 components were identified, representing 96.8-99.8% of the oil composition. The oils were characterized by a high content of oxygenated monoterpenes (38.6-62.7%), while monoterpene and sesquiterpene hydrocarbons accounted for 2.3-41.9 and 5.1-20.1% of the identified constituents, respectively. The main oxygenated derivatives were nerol (2.8-12.8%) and its ester derivative neryl acetate (5.6-45.9%). To compare the chemical variability of the species within Elba Island and between the island and other localities within the Mediterranean area, studied previously, multivariate statistical analysis was performed. The results obtained showed a difference in the composition of the essential oils of H. italicum from Elba Island, mainly due to the environment where the plant grows, and, in particular, to the soil type. These hypotheses were further confirmed by the comparison of these oils with essential oils obtained from H. italicum collected on other islands of the Tuscan archipelago. Copyright © 2013 Verlag Helvetica Chimica Acta AG, Zürich.

  1. The influence of origin of Helichrysum arenarium (L. Moench individuals on their inflorescence yield and germination ability

    Anna K. Sawilska

    2012-12-01

    Full Text Available Helichrysum arenarium (L. Moench is a perennial of the Asteraceae family. The species is partially protected in Poland. Its inflorescence is a source of valuable herbal material. The amount of fresh and dry mass of inflorescences collected from plants growing in natural stands and those obtained from experimental plantations was analyzed. The plants growing in the plantation were obtained from in vitro cultures. Germination ability of achenes was also tested. The number of flowering shoots per plant, the number of plants per area unit as well as the fresh and dry mass of inflorescences depended significantly on the soil conditions and precipitation. Cultivation of H. arenarium gives a significantly higher fresh and dry mass of inflorescences per plant and a higher yield per area unit. The yield of herbal material from a plantation can vastly exceed that from the natural stands. Stratification of achenes prior to their germination resulted in an increase in the number of seedlings by 9.6%. Germination ability markedly decreased with time. Therefore, it is likely that the achenes form a transient seed bank. Achenes from plants obtained by in vitro method exhibited the lowest germination ability, so they should not be used as seed material.

  2. Thyristors for dc transmission

    1966-05-06

    As a first stage towards determining the feasibility of applying thyristors to hvdc converter terminals, the Westinghouse Electric Corporation has built a converter laboratory capable of testing thyristors under conditions similar to those which would have to be met in a 200 kV dc system. The equipment has been designed to test a 5 kV 600 A group of thyrisotrs, elevated 200 kV above earth. This rating has been chosen so that there would be a sufficient number of thyristors in series to enable the gating and voltage division characteristics to be investigated and at the same time the group could be operated at a potential equivalent to a complete 200 kV dc bridge.

  3. TOPOLOGICAL REVIEW AND ANALYSIS OF DC-DC BOOST CONVERTERS

    V. INDRA GANDHI

    2017-06-01

    Full Text Available DC voltage boost up is essential in numerous applications; especially considering Photovoltaic (PV based renewable power generation system. The conventional DC-DC boost converter is the most admired configuration for this scheme, even if the converter efficiency is restricted at duty cycle near to maximum value. In order to find solution to the problem and improve its conversion capability, many converter configurations have been implemented so far. With this circumstance, this research work proposes to give overview of a few most imperative research works related to DC-DC boost converters. Some configurations are covered and classified basically based on the application. The major benefits and disadvantages related to the available techniques are also briefly conveyed. At last, a proper evaluation is recognized among the important types of DC-DC boost converters in terms of efficiency, number of components, and stability.

  4. An Integrated Multifunctional Bidirectional AC/DC and DC/DC Converter for Electric Vehicles Applications

    Liwen Pan; Chengning Zhang

    2016-01-01

    This paper presents an on-board vehicular battery charger that integrates bidirectional AC/DC converter and DC/DC converter to achieve high power density for application in electric vehicles (EVs). The integrated charger is able to transfer electrical energy between the battery pack and the electric traction system and to function as an AC/DC battery charger. The integrated charger topology is presented and the design of passive components is discussed. The control schemes are developed for m...

  5. Chemical composition, plant genetic differences, and antifungal activity of the essential oil of Helichrysum italicum G. Don ssp. microphyllum (Willd) Nym.

    Angioni, Alberto; Barra, Andrea; Arlorio, Marco; Coisson, Jean Daniel; Russo, Maria T; Pirisi, Filippo M; Satta, Maurizio; Cabras, Paolo

    2003-02-12

    The chemical composition of the essential oil of the Sardinian dwarf curry plant [Helichrysum italicum G. Don ssp. microphyllum (Willd) Nym] was studied. Genetic analysis suggested the presence of two chemotypes; morphological and chemical differences confirmed the presence of two chemotypes (A and B). The maximum yields were 0.18 and 0.04% (v/w) for flowering tops and stems, respectively. The concentrations of nerol and its esters (acetate and propionate), limonene, and linalool reach their highest values during the flowering stage both in flowers and in stems. Besides the essential oil, type B showed an interesting antifungal activity.

  6. On and off controlled resonant dc-dc power converter

    2015-01-01

    The present invention relates to a resonant DC-DC power converter comprising an input side circuit comprising a positive and a negative input terminal for receipt of an input voltage or current and an output side circuit comprising positive and negative output terminals for supply of a converter...... output voltage and connection to a converter load. The resonant DC-DC power converter further comprises a rectification circuit connected between an output of a resonant network and the output side circuit. The resonant network is configured for alternatingly being charged from the input voltage...... or current and discharged through the rectification circuit by a first controllable switch arrangement in accordance with a first switch control signal. A second controllable switch arrangement of the resonant DC-DC power converter is configured to select a first impedance characteristic of the resonant...

  7. DC Cable for Railway

    Tomita, Masaru

    The development of a superconducting cable for railways has commenced, assuming that a DC transmission cable will be used for electric trains. The cable has been fabricated based on the results of current testing of a superconducting wire, and various evaluation tests have been performed to determine the characteristics of the cable. A superconducting transmission cable having zero electrical resistance and suitable for railway use is expected to enhance regeneration efficiency, reduce power losses, achieve load leveling and integration of sub-stations, and reduce rail potential.

  8. Auxiliary resonant DC tank converter

    Peng, Fang Z.

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  9. PENGGUNAAN FUZZY LOGIC UNTUK KONTROL PARALLEL CONVERTER DC-DC

    Bambang Prio Hartono

    2012-09-01

    Full Text Available Abstract: Using system fuzzy logic as control  technology have been used on low load dc-dc converter with combined parallel compiled  dc-dc converter can  obtain big load.   With existence of differrence of component parameter and each parallel compiled converter can obtained different current  and voltage output.  Function of controller  for to do adjustment, so that current which is applied  to  load by each converter  can be obtained  difference error as small as possible or same. The object of research is developing design of large signal dc-dc converter which is  combined with using  FLC so that  obtain  better performance.  To get better performance have been made plant model and simulation with CDE method.  The more systematic  system and design is needed to overcome bigger load  on dc-dc converter, so that parallel  compiled current master slave control system on dc-dc converter with using fuzzy logic  controller is used. Result of  research showed that error or difference of  current  which is applied to load can handled by fuzzy logic  controller.  Technic of current and voltage controller co to do adjustment current and voltage distribution  equally to load.  Distribution of iL1,iL2 and  output voltage Vo on dc-dc  converter with load 2,25 until  7,875 and voltage  100  until 120 volt,  load current beetwen  12 until 48, % relatif  error  Vo  0,4% until  0,9%.

  10. Step-Up DC-DC Power Converter

    2015-01-01

    The present invention relates to a step-up DC-DC power converter which comprises a primary side circuit and a secondary side circuit coupled through a galvanic isolation barrier. The primary side circuit comprises a positive and a negative input terminal for receipt of an input voltage and an input...... being charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier in accordance with a switch control signal to produce the converter output voltage. The step-up DC-DC power converter comprises an electrical short-circuit connection across the galvanic...

  11. [CONTENT OF OXIDATIVE STRESS MARKERS IN BLOOD PLASMA UNDER THE ACTION OF EXTRACTS OF GRATIOLA OFFICINALIS L., HELICHRYSUM ARENARIUM (L.) MOENCH, AND ANTHOCYANIN FORMS OF ZEA MAYS L].

    Durnova, N A; Afanas'eva, G A; Kurchatova, M N; Zaraeva, N V; Golikov, A G; Bucharskaya, A B; Golikov, A G; Bucharskaya, A B; Plastun, V O; Andreeva, N V

    2015-01-01

    The effect of aqueous solutions of dry ethanol extracts of Gratiola officinalis L., Helichrysum arenarium (L.) Moench, and anthocyanin forms of Zea mays L. on the dioxidin-induced lipid peroxidation in blood has been studied on rats. It is established that all these extracts are capable of reducing the amount of avera- ge-mass (AM) molecules and malonic dialdehyde (MDA) in rat blood plasma. The extract of Gratiola officinalis L. reduces the concentration of AM and MDA moleules by 43%. The extract of Helichrysum arenarium (L.) Moench reduces the concentration of AM molecules on the average by 18.66% (within 9.22 -34.81%) and MDA by 49.36% (within 34.12-79.75%). The Extract of anthocyanin forms of Zea mays L. does not reduce the concentration of AM mo- lecules, but reduces the amount of MDA in the blood of rats on average by 27.88% (within 21.58-37.82%) (p < 0.01).

  12. Chemical composition and biological activity of the essential oil from Helichrysum microphyllum Cambess. ssp. tyrrhenicum Bacch., Brullo e Giusso growing in La Maddalena Archipelago, Sardinia.

    Ornano, Luigi; Venditti, Alessandro; Sanna, Cinzia; Ballero, Mauro; Maggi, Filippo; Lupidi, Giulio; Bramucci, Massimo; Quassinti, Luana; Bianco, Armandodoriano

    2015-01-01

    Helichrysum microphyllum Cambess. subsp. tyrrhenicum Bacch., Brullo e Giusso (Asteraceae), previously known as Helichrysum italicum ssp. microphyllum (Willd.) Nyman, is one of the many endemic species growing in Sardinia, Corsica and Balearic Islands. In the present work the composition of the essential oil obtained from a population of H. microphyllum ssp. thyrrenicum growing in a littoral location of La Maddalena Archipelago was investigated by GC-FID and CG-MS. The major compounds of the oil were the monoterpene ester neryl acetate (18.2%), the oxygenated sesquiterpene 5-eudesmen-11-ol (rosifoliol, 11.3%), the sequiterpene hydrocarbons δ-cadinene (8.4%) and γ-cadinene (6.7%), showing a peculiar composition in comparison with other Sardinian populations. The oil was tested for cytotoxicity on three human tumor cell lines (MDA-MB 231, HCT116 and A375) by MTT assay showing a strong inhibitory activity on human malignant melanoma cells A375 (IC50 of 16 µg/ml). In addition the oil was assessed for antioxidant activity by DPPH and ABTS assay.

  13. Helichrysum gymnocephalum Essential Oil: Chemical Composition and Cytotoxic, Antimalarial and Antioxidant Activities, Attribution of the Activity Origin by Correlations

    François Couderc

    2011-09-01

    Full Text Available Helichrysum gymnocephalum essential oil (EO was prepared by hydrodistillation of its leaves and characterized by GC-MS and quantified by GC-FID. Twenty three compounds were identified. 1,8-Cineole (47.4%, bicyclosesquiphellandrene (5.6%, γ-curcumene (5.6%, α-amorphene (5.1% and bicyclogermacrene (5% were the main components. Our results confirmed the important chemical variability of H. gymnocephalum. The essential oil was tested in vitro for cytotoxic (on human breast cancer cells MCF-7, antimalarial (Plasmodium falciparum: FcB1-Columbia strain, chloroquine-resistant and antioxidant (ABTS and DPPH assays activities. H. gymnocephalum EO was found to be active against MCF-7 cells, with an IC50 of 16 ± 2 mg/L. The essential oil was active against P. falciparum (IC50 = 25 ± 1 mg/L. However, the essential oil exhibited a poor antioxidant activity in the DPPH (IC50 value > 1,000 mg/L and ABTS (IC50 value = 1,487.67 ± 47.70 mg/L assays. We have reviewed the existing results on the anticancer activity of essential oils on MCF-7 cell line and on their antiplasmodial activity against the P. falciparum. The aim was to establish correlations between the identified compounds and their biological activities (antiplasmodial and anticancer. β-Selinene (R² = 0.76, α-terpinolene (R² = 0.88 and aromadendrene (R² = 0.90 presented a higher relationship with the anti-cancer activity. However, only calamenene (R² = 0.70 showed a significant correlation for the antiplasmodial activity.

  14. Inhibition of Oxidative Stress and Skin Aging-Related Enzymes by Prenylated Chalcones and Other Flavonoids from Helichrysum teretifolium.

    Popoola, Olugbenga K; Marnewick, Jeanine L; Rautenbach, Fanie; Ameer, Farouk; Iwuoha, Emmanuel I; Hussein, Ahmed A

    2015-04-20

    Ten flavonoid-related structures viz. heliteretifolin (1), isoxanthohumol (2), 2',4',6'-trihydroxy-3'-prenylchalcone (3), isoglabranin (4), glabranin (5), 7-methoxy-isoglabranin (6), quercetin (7), 4'-methoxyquercetin (8), 4'-methoxykaempferol (9) and mosloflavone (10) were isolated from a H. teretifolium methanolic extract and identified. One of them (compound 1) is reported for the first time from a natural source, while compounds 6, 8-10 were isolated for the first time from the genus Helichrysum. The total extract of H. teretifolium showed potent antioxidant activity. When tested for total antioxidant capacity compound 3 possesses moderate biological activity compared to 2, which displayed some of the highest TEAC values (4529.01 ± 2.44; 4170.66 ± 6.72) µM TE/g, respectively. Compounds 7 and 8 demonstrated the highest inhibitory activities on Fe2+-induced lipid peroxidation (IC50 = 2.931; 6.449 µg/mL); tyrosinase (8.092; 27.573) and elastase (43.342; 86.548). Additionally, the total antioxidant capacities measured as FRAP (4816.31 ± 7.42; 3584.17 ± 0.54) µM AAE/g, and ORAC for hydroxyl radical (7.265 ± 0.71; 6.779 ± 3.40) × 106 and peroxyl radical (17.836 ± 2.90; 12.545 ± 5.07) × 103 µM TE/g were also observed for compounds 7 and 8, respectively. In conclusion, H. teretifolium total extract represents a rich source of bioactive constituents with potent antioxidant and moderate anti-tyrosinase and anti-elastase activities that can help to avert accumulation of free radicals in the body, and could therefore be good candidates for the prevention and/or treatment of skin-related conditions, such as aging. This is the first scientific report on the chemical and biological profile of H. teretifolium.

  15. Helichrysum gymnocephalum essential oil: chemical composition and cytotoxic, antimalarial and antioxidant activities, attribution of the activity origin by correlations.

    Afoulous, Samia; Ferhout, Hicham; Raoelison, Emmanuel Guy; Valentin, Alexis; Moukarzel, Béatrice; Couderc, François; Bouajila, Jalloul

    2011-09-29

    Helichrysum gymnocephalum essential oil (EO) was prepared by hydrodistillation of its leaves and characterized by GC-MS and quantified by GC-FID. Twenty three compounds were identified. 1,8-Cineole (47.4%), bicyclosesquiphellandrene (5.6%), γ-curcumene (5.6%), α-amorphene (5.1%) and bicyclogermacrene (5%) were the main components. Our results confirmed the important chemical variability of H. gymnocephalum. The essential oil was tested in vitro for cytotoxic (on human breast cancer cells MCF-7), antimalarial (Plasmodium falciparum: FcB1-Columbia strain, chloroquine-resistant) and antioxidant (ABTS and DPPH assays) activities. H. gymnocephalum EO was found to be active against MCF-7 cells, with an IC(50) of 16 ± 2 mg/L. The essential oil was active against P. falciparum (IC(50) = 25 ± 1 mg/L). However, the essential oil exhibited a poor antioxidant activity in the DPPH (IC(50) value > 1,000 mg/L) and ABTS (IC(50) value = 1,487.67 ± 47.70 mg/L) assays. We have reviewed the existing results on the anticancer activity of essential oils on MCF-7 cell line and on their antiplasmodial activity against the P. falciparum. The aim was to establish correlations between the identified compounds and their biological activities (antiplasmodial and anticancer). β-Selinene (R² = 0.76), α-terpinolene (R² = 0.88) and aromadendrene (R² = 0.90) presented a higher relationship with the anti-cancer activity. However, only calamenene (R² = 0.70) showed a significant correlation for the antiplasmodial activity.

  16. Comparative analysis of the oil and supercritical CO(2) extract of Artemisia arborescens L. and Helichrysum splendidum (Thunb.) Less.

    Marongiu, Bruno; Piras, Alessandra; Porcedda, Silvia

    2006-05-10

    Isolation of volatile concentrate from the dried leaves of Artemisia arborescens and of Helichrysum splendidum has been obtained by supercritical extraction with carbon dioxide. To obtain a pure volatile extract devoid of cuticular waxes, the extraction products were fractionated in two separators operating in series. A good extraction process was obtained operating at 90 bar and 50 degrees C in the extraction vessel, at 90 bar and at -5 degrees C in the first separator and at a pressure between 20 and 15 bar and temperatures in the range 10-20 degrees C in the second one. The composition of the volatile concentrate has been analyzed by GC/MS. The volatile concentrate of A. arborescens was found to contain: trans-thujone (13.96%), camphor (6.15%) and chamazulene (5.95%). The main constituents in the extract of H. splendidum were: germacrene D-4-ol (17.08%), germacrene D (9.04%), bicyclogermacrene (8.79%) and delta-cadinene (8.43%). A comparison with the oils obtained by hydrodistillation is also given. The differences observed between the composition of the SFE volatile concentrates and of the hydrodistilled (HD) oils were relevant. Indeed, the HD oils had a blue color whereas the volatile concentrates were pale yellow. The HD oil of H. splendidum had a blue color due to the presence of guaiazulene (0.42% vs 0%), whereas the coloration of HD oil of A. arborecens was due to the high concentration of chamazulene (26.64% vs 3.37%).

  17. DC Distribution Systems and Microgrids

    Dragicevic, Tomislav; Anvari-Moghaddam, Amjad; Quintero, Juan Carlos Vasquez

    2017-01-01

    summarized. Due to its attractive characteristics in terms of compliance with modern generation, storage and electronic load technologies, high reliability and current carrying capacity, as well as simple control, DC systems are already an indispensable part of power systems. Moreover, the existing......A qualitative overview of different hardware topologies and control systems for DC MGs has been presented in this chapter. Some challenges and design considerations of DC protections systems have also been discussed. Finally, applications of DC MGs in emerging smart grid applications have been...... challenges such as protection issues will be effectively resolved in the near future due to fast progress of semiconductor technology which is a key enabler cheap and reliable future DC solid-state protection systems. Therefore, it is the view of the author that more and more DC systems will appear...

  18. Very High Frequency Half Bridge DC/DC Converter

    Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

    2014-01-01

    This paper presents the first, off chip, class DE (resonant half bridge) converter working in the Very High Frequency (VHF) range. The benefits of using half bridge circuits both in the inverter and rectifier part of a VHF resonant dc/dc converter are analyzed and design equations for all...

  19. SCM Handbooks for dc-to-dc Converters

    Lee, F.; Mohmoud, M.; Yu, Y.

    1984-01-01

    Two documents aid in design of control modules for dc-to-dc converters. Features of SCM include: Adaptive stability, power component stress limiting, implementation of various control laws, unified design approach. Analysis and quidelines contained in handbooks enable engineer to design SCM circuit and confidently predict resulting overall performance.

  20. Sheppard-Taylor Isolated High Boost DC-DC Converter

    Chub, Andrii; Siwakoti, Yam Prasad; Vinnikov, Dmitri

    2017-01-01

    This paper presents a new galvanically isolated step-up dc-dc converter intended for low-power but high step-up applications. The proposed converter is capable of regulating output voltage within a wide range of the input voltage or load variations. In contrast to competitors, the converter can...

  1. Dc-To-Dc Converter Uses Reverse Conduction Of MOSFET's

    Gruber, Robert P.; Gott, Robert W.

    1991-01-01

    In modified high-power, phase-controlled, full-bridge, pulse-width-modulated dc-to-dc converters, switching devices power metal oxide/semiconductor field-effect transistors (MOSFET's). Decreases dissipation of power during switching by eliminating approximately 0.7-V forward voltage drop in anti-parallel diodes. Energy-conversion efficiency increased.

  2. A Current-Fed Isolated Bidirectional DC-DC Converter

    Sun, Xiaofeng; Wu, Xiaoying; Shen, Yanfeng

    2017-01-01

    This paper proposes a current-fed isolated bidirectional DC-DC converter (CF-IBDC) which has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes...

  3. Power flow analysis for DC voltage droop controlled DC microgrids

    Li, Chendan; Chaudhary, Sanjay; Dragicevic, Tomislav

    2014-01-01

    This paper proposes a new algorithm for power flow analysis in droop controlled DC microgrids. By considering the droop control in the power flow analysis for the DC microgrid, when compared with traditional methods, more accurate analysis results can be obtained. The algorithm verification is ca...

  4. A DC Transformer

    Youngquist, Robert C.; Ihlefeld, Curtis M.; Starr, Stanley O.

    2013-01-01

    A component level dc transformer is described in which no alternating currents or voltages are present. It operates by combining features of a homopolar motor and a homopolar generator, both de devices, such that the output voltage of a de power supply can be stepped up (or down) with a corresponding step down (or up) in current. The basic theory for this device is developed, performance predictions are made, and the results from a small prototype are presented. Based on demonstrated technology in the literature, this de transformer should be scalable to low megawatt levels, but it is more suited to high current than high voltage applications. Significant development would be required before it could achieve the kilovolt levels needed for de power transmission.

  5. The performance of the DC motor by the PID controlling PWM DC-DC boost converter

    Can, Erol; Sayan, Hasan Hüseyin

    2017-01-01

    This paper presents the PID controlling direct current (DC) to the direct current boost converter feds DC motor which has a 3.68 kW and 240 V of DC voltage input on its characteristics. What is first formed is the boost converter mathematical model at the design stage. Secondly, a mathematical model of the DC motor is created so that the boost converter with the machine can be established and modeled at the Matlab Simulink. The PID controller is considered for arranging a pulse width modulati...

  6. 75 FR 61989 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-8-31, DC-8-32, DC-8-33, DC-8-41...

    2010-10-07

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 8-31, DC-8-32, DC-8-33, DC-8-41, DC-8-42, and... to all of the McDonnell Douglas Corporation airplanes identified above. The existing AD currently... the following new airworthiness directive (AD): 2010-21-03 McDonnell Douglas Corporation: Amendment 39...

  7. Triple voltage dc-to-dc converter and method

    Su, Gui-Jia

    2008-08-05

    A circuit and method of providing three dc voltage buses and transforming power between a low voltage dc converter and a high voltage dc converter, by coupling a primary dc power circuit and a secondary dc power circuit through an isolation transformer; providing the gating signals to power semiconductor switches in the primary and secondary circuits to control power flow between the primary and secondary circuits and by controlling a phase shift between the primary voltage and the secondary voltage. The primary dc power circuit and the secondary dc power circuit each further comprising at least two tank capacitances arranged in series as a tank leg, at least two resonant switching devices arranged in series with each other and arranged in parallel with the tank leg, and at least one voltage source arranged in parallel with the tank leg and the resonant switching devices, said resonant switching devices including power semiconductor switches that are operated by gating signals. Additional embodiments having a center-tapped battery on the low voltage side and a plurality of modules on both the low voltage side and the high voltage side are also disclosed for the purpose of reducing ripple current and for reducing the size of the components.

  8. Bi-Directional DC-DC Converter for PHEV Applications

    Abas Goodarzi

    2011-01-31

    Plug-In Hybrid Electric Vehicles (PHEV) require high power density energy storage system (ESS) for hybrid operation and high energy density ESS for Electric Vehicle (EV) mode range. However, ESS technologies to maximize power density and energy density simultaneously are not commercially feasible. The use of bi-directional DC-DC converter allows use of multiple energy storage, and the flexible DC-link voltages can enhance the system efficiency and reduce component sizing. This will improve fuel consumption, increase the EV mode range, reduce the total weight, reduce battery initial and life cycle cost, and provide flexibility in system design.

  9. Helichrysum italicum growing on metalliferous areas as a potential tool in phytostabilization of metal-contaminated soils.

    Bini, Claudio; Maleci, Laura; Giuliani, Claudia

    2015-04-01

    Plants that colonize metalliferous soils have developed physiological mechanisms that allow to tolerate high metal concentrations. Generally, metal uptake by these plants is not suppressed, but a detoxification process occurs, as a response to different strategies: some plants (accumulators) concentrate metals in the aerial parts, while others (excluders) present low metal concentrations in the aerial parts, since metals are arrested in their roots. In several regions of Italy (e.g. Veneto, Sardinia, Tuscany), numerous abandoned mine sites are present; On these metal-contaminated soils grow both metalliferous (e.g. Silene paradoxa) and non-metalliferous plants (e.g. Taraxacum officinale). Among them, Helichrysum italicum deserved attention since it is known as essential oil producer and is also used as a medicinal plant for its anti-inflammatory properties; for this reason, it must undergo the Drug Master File certifying the absence of chemical impurities and heavy metals. Samples of the whole plant (roots, leaves and flowers) of H. italicum have been collected at various sites, both mined and not mined, in order to ascertain its ability to uptake and translocate metals from roots to the aerial parts. Fresh and embedded material was examined by Light microscopy and Electron Microscopy (Scanning and Transmission) to ascertain possible damages in plant morphology. Dried samples were crushed, digested with HNO3 and analysed by ICP-OE technique for heavy metal (Cu, Fe, Mn, Zn) concentrations. Preliminary observations on the morphology of the different samples do not show significant differences in the leaf structure. The inorganic chemical composition of H. italicum was characterized by high metal content. Preliminary results of our analyses show that H. italicum accumulate metals (Mn, Zn) in roots, but do not translocate metals to the aerial parts; therefore, it may be considered an excluder plant. On the basis of our results, the aerial parts (leaves, flowers) of

  10. Inhibition of Oxidative Stress and Skin Aging-Related Enzymes by Prenylated Chalcones and Other Flavonoids from Helichrysum teretifolium

    Olugbenga K. Popoola

    2015-04-01

    Full Text Available Ten flavonoid-related structures viz. heliteretifolin (1, isoxanthohumol (2, 2',4',6'-trihydroxy-3'-prenylchalcone (3, isoglabranin (4, glabranin (5, 7-methoxy-isoglabranin (6, quercetin (7, 4'-methoxyquercetin (8, 4'-methoxykaempferol (9 and mosloflavone (10 were isolated from a H. teretifolium methanolic extract and identified. One of them (compound 1 is reported for the first time from a natural source, while compounds 6, 8–10 were isolated for the first time from the genus Helichrysum. The total extract of H. teretifolium showed potent antioxidant activity. When tested for total antioxidant capacity compound 3 possesses moderate biological activity compared to 2, which displayed some of the highest TEAC values (4529.01 ± 2.44; 4170.66 ± 6.72 µM TE/g, respectively. Compounds 7 and 8 demonstrated the highest inhibitory activities on Fe2+-induced lipid peroxidation (IC50 = 2.931; 6.449 µg/mL; tyrosinase (8.092; 27.573 and elastase (43.342; 86.548. Additionally, the total antioxidant capacities measured as FRAP (4816.31 ± 7.42; 3584.17 ± 0.54 µM AAE/g, and ORAC for hydroxyl radical (7.265 ± 0.71; 6.779 ± 3.40 × 106 and peroxyl radical (17.836 ± 2.90; 12.545 ± 5.07 × 103 µM TE/g were also observed for compounds 7 and 8, respectively. In conclusion, H. teretifolium total extract represents a rich source of bioactive constituents with potent antioxidant and moderate anti-tyrosinase and anti-elastase activities that can help to avert accumulation of free radicals in the body, and could therefore be good candidates for the prevention and/or treatment of skin-related conditions, such as aging. This is the first scientific report on the chemical and biological profile of H. teretifolium.

  11. RESONANT STEP-DOWN DC-DC POWER CONVERTERS

    2015-01-01

    The present invention relates to a resonant step-down DC-DC power converter which comprises a primary side circuit and a secondary side circuit coupled through a galvanic isolation barrier. The primary side circuit comprises a positive and a negative input terminal for receipt of an input voltage...... charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier by a semiconductor switch arrangement in accordance with a switch control signal to produce the converter output voltage. The resonant step-down DC-DC power converter comprises an electrical short......-circuit connection across the galvanic isolation barrier connecting, in a first case, the second negative electrode of the output capacitor to the positive input terminal of the primary side circuit or, in a second case, connecting the second positive electrode of the output capacitor to the negative input terminal...

  12. Decentralized Interleaving of Paralleled Dc-Dc Buck Converters: Preprint

    Johnson, Brian B [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rodriguez, Miguel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sinha, Mohit [University of Minnesota; Dhople, Sairaj [University of Minnesota; Poon, Jason [University of California at Berkeley

    2017-09-01

    We present a decentralized control strategy that yields switch interleaving among parallel connected dc-dc buck converters without communication. The proposed method is based on the digital implementation of the dynamics of a nonlinear oscillator circuit as the controller. Each controller is fully decentralized, i.e., it only requires the locally measured output current to synthesize the pulse width modulation (PWM) carrier waveform. By virtue of the intrinsic electrical coupling between converters, the nonlinear oscillator-based controllers converge to an interleaved state with uniform phase-spacing across PWM carriers. To the knowledge of the authors, this work represents the first fully decentralized strategy for switch interleaving of paralleled dc-dc buck converters.

  13. Active pre-filters for dc/dc Boost regulators

    Carlos Andrés Ramos-Paja

    2014-05-01

    Full Text Available This paper proposes an active pre-filter to mitigate the current harmonics generated by classical dc/dc Boost regulators, which generate current ripples proportional to the duty cycle. Therefore, high output voltage conditions, i.e., high voltage conversion ratios, produce high current harmonics that must be filtered to avoid damage or source losses. Traditionally, these current components are filtered using electrolytic capacitors, which introduce reliability problems because of their high failure rate. The solution introduced in this paper instead uses a dc/dc converter based on the parallel connection of the Boost canonical cells to filter the current ripples generated by the Boost regulator, improving the system reliability. This solution provides the additional benefits of improving the overall efficiency and the voltage conversion ratio. Finally, the solution is validated with simulations and experimental results.

  14. Linking DC together with TRSL

    Haxthausen, Anne Elisabeth; Yong, X.

    2000-01-01

    in a method for real-time developments. An operational semantics with behavior is specified for TRSL. It is defined what its means for a TRSL process to satisfy a DC requirement, and a method for verifying whether the satisfaction relation holds or not is provided. Our contribution also demonstrates a general......Duration Calculus (DC) is an interval-based real-time logic, which can be used in capturing and eliciting users' real-time requirements. The Timed RAISE Specification Language (TRSL) is an extension of the RAISE Specification Language with real-time features. This paper links DC and TRSL together...

  15. DC Microgrids—Part II

    Dragicevic, Tomislav; Lu, Xiaonan; Quintero, Juan Carlos Vasquez

    2016-01-01

    distribution applications such as traction, telecom, vehicular and distributed power systems can be classified under DC MG framework and ongoing development and expansion of the field is largely influenced by concepts used over there. This paper aims firstly to shed light on the practical design aspects of DC...... MG technology concerning typical power hardware topologies and their suitability for different emerging smart grid applications. Then, an overview of the state of the art in DC MG protection and grounding is provided. Owing to the fact that there is no zero current crossing, an arc that appears upon...

  16. DC-Compensated Current Transformer.

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-20

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component.

  17. DC injection into low voltage AC networks

    NONE

    2005-07-01

    This report summarises the results of a study investigating the impact of levels of injected DC current injections on a low voltage AC distribution network systems in order to recommend acceptable limits of DC from microgeneration. Relevant literature is reviewed, and the impact of DC levels in distribution transformers, transformer modelling, and instrumental transformers are discussed. The impact of DC in residual current devices (RCD) and in domestic electricity watt hour meters is examined along with DC enhanced corrosion, corrosion failure, and the measurement of DC current injection. Sources of DC injection outlined include DC from computer power supplies, network faults, geomagnetic phenomena, lighting circuits/dimmers, and embedded generators.

  18. Isolated step-down DC -DC converter for electric vehicles

    Kukovinets, O. V.; Sidorov, K. M.; Yutt, V. E.

    2018-02-01

    Modern motor-vehicle industrial sector is moving rapidly now towards the electricity-driving cars production, improving their range and efficiency of components, and in particular the step-down DC/DC converter to supply the onboard circuit 12/24V of electric vehicle from the high-voltage battery. The purpose of this article - to identify the best circuitry topology to design an advanced step-down DC/DC converters with the smallest mass, volume, highest efficiency and power. And this will have a positive effect on driving distance of electric vehicle (EV). On the basis of computational research of existing and implemented circuit topologies of step-down DC/DC converters (serial resonant converter, full bridge with phase-shifting converter, LLC resonant converter) a comprehensive analysis was carried out on the following characteristics: specific volume, specific weight, power, efficiency. The data obtained was the basis for the best technical option - LLC resonant converter. The results can serve as a guide material in the process of components design of the traction equipment for electric vehicles, providing for the best technical solutions in the design and manufacturing of converting equipment, self-contained power supply systems and advanced driver assistance systems.

  19. Phytochemical study of Helichrysum italicum (Roth) G. Don: Spectroscopic elucidation of unusual amino-phlorogucinols and antimicrobial assessment of secondary metabolites from medium-polar extract.

    D'Abrosca, Brigida; Buommino, Elisabetta; Caputo, Pina; Scognamiglio, Monica; Chambery, Angela; Donnarumma, Giovanna; Fiorentino, Antonio

    2016-12-01

    Three unusual amino-phloroglucinols, named helichrytalicines A-C, along with seventeen known compounds including acetophenones, tremetrone derivatives, low-molecular weight phenols, flavonol glucosides, have been isolated from the medium-polar extract of Helichrysum italicum (Roth) G. Don, a medicinal plant typical of the Mediterranean vegetation. The structures of the compounds have been elucidated based on extensive 2D-NMR spectroscopic analyses, including COSY, TOCSY, HSQC, CIGAR-HMBC, H2BC and HSQC-TOCSY, along with Q-TOF HRMS 2 analysis. Stereostructure of the new compounds has been elucidated by Mosher's method and NOESY experiment. Antimicrobial properties against Staphylococcus epidermidis of selected compounds have been evaluated. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Partitioning the relative contributions of inorganic plant composition and soil characteristics to the quality of Helichrysum italicum subsp. italicum (Roth) G. Don fil. essential oil.

    Bianchini, Ange; Santoni, François; Paolini, Julien; Bernardini, Antoine-François; Mouillot, David; Costa, Jean

    2009-07-01

    Composition of Helichrysum italicum subsp. italicum essential oil showed chemical variability according to vegetation cycle, environment, and geographic origins. In the present work, 48 individuals of this plant at different development stages and the corresponding root soils were sampled: i) 28 volatile components were identified and measured in essential oil by using GC and GC/MS; ii) ten elements from plants and soils have been estimated using colorimetry in continuous flux, flame atomic absorption spectrometry, or emission spectrometry (FAAS/FAES); iii) texture and acidity (real and potential) of soil samples were also reported. Relationships between the essential-oil composition, the inorganic plant composition, and the soil characteristics (inorganic composition, texture, and acidity) have been established using multivariate analysis such as Principal Component Analysis (PCA) and partial Redundancy Analysis (RDA). This study demonstrates a high level of intraspecific differences in oil composition due to environmental factors and, more particularly, soil characteristics.

  1. Medicinal flowers. XXVII. New flavanone and chalcone glycosides, arenariumosides I, II, III, and IV, and tumor necrosis factor-alpha inhibitors from everlasting, flowers of Helichrysum arenarium.

    Morikawa, Toshio; Wang, Li-Bo; Nakamura, Seikou; Ninomiya, Kiyofumi; Yokoyama, Eri; Matsuda, Hisashi; Muraoka, Osamu; Wu, Li-Jun; Yoshikawa, Masayuki

    2009-04-01

    The methanolic extract from the flowers of Helichrysum arenarium L. MOENCH was found to show inhibitory effect on tumor necrosis factor-alpha (TNF-alpha, 1 ng/ml)-induced cytotoxicity in L929 cells. From the methanolic extract, 50 constituents including four new flavanone and chalcone glycosides named arenariumosides I (1), II (2), III (3), and IV (4) were isolated. The stereostructures of 1-4 were elucidated on the basis of chemical and physicochemical evidence. Among the constituents, naringenin 7-O-beta-D-glucopyranoside (7), apigenin 7-O-beta-D-glucopyranoside (14), apigenin 7-O-gentiobioside (16), and apigenin 7,4'-di-O-beta-D-glucopyranoside (17) significantly inhibited TNF-alpha-induced cytotoxicity in L929 cells at 30 microM.

  2. An evaluation of a new approach to the regeneration of Helichrysum italicum (Roth) G. Don, and the molecular characterization of the variation among sets of differently derived regenerants.

    Perrini, Rosaria; Alba, Vittorio; Ruta, Claudia; Morone-Fortunato, Irene; Blanco, Antonio; Montemurro, Cinzia

    2009-01-01

    A protocol for the induction of regeneration from leaves of Helichrysum italicum was established. Calli were found to form on the basal medium only when it was supplemented with thidiazuron (TDZ) alone or in combination with naphthalene acetic acid (NAA), with a percentage ranking of at least 80%. The hormone-free medium showed the highest percentage of shoot regeneration (62%) even though no callus formed. AFLP markers were employed to verify tissue culture-induced variation in the regenerated plantlets obtained by direct shoot regeneration or the indirect shoot regeneration process (callus formation). Seven out of the eleven AFLP primer pairs yielded polymorphic patterns. The average number of fragments per primer pair was 64.1. Singletons were represented by 12 (2.7%) fragments. Student's T-test was performed both on the average number of shared fragments and on the nucleotide diversity, and no significant statistical difference was observed between the two regeneration treatments.

  3. Borehole DC-12 hydrostratigraphic chart

    Gephart, R.E.

    1981-09-01

    This hydrostratigraphic chart identifies the basic stratigraphy and preliminary hydrologic testing results for Borehole DC-12. This borehole was cored through the Saddle Mountains and Wanapum basalt formations and into the Grande Ronde. Selected zones were hydrologically tested during coring

  4. Borehole DC-14 hydrostratigraphic chart

    Gephart, R.E.

    1981-09-01

    This hydrostratigraphic chart identifies the basic stratigraphy and preliminary hydrologic testing results for Borehole DC-14. This borehole was cored through the Saddle Mountains and Wanapum basalt formations and into the Grande Ronde. Selected zones were hydrologically tested during coring

  5. Borehole DC-15 hydrostratigraphic chart

    Gephart, R.E.

    1981-09-01

    This hydrostratigraphic chart identifies the basic stratigraphy and preliminary hydrologic testing results for Borehole DC-15. This borehole was cored through the Saddle Mountains and Wanapum basalt formations and into the Grande Ronde. Selected zones were hydrologically tested during coring

  6. Five-Level Active-Neutral-Point-Clamped DC/DC Converter for Medium-Voltage DC Grids

    Liu, Dong; Deng, Fujin; Chen, Zhe

    2017-01-01

    This paper proposes a five-level active-neutralpoint- clamped (5L-ANPC) dc/dc converter for applications in medium voltage dc (MVDC) grids. A modulation strategy is proposed for the 5L-ANPC dc/dc converter to generate multilevel voltage waveforms, which can effectively reduce voltage change rate dv...... effectively eliminate high voltage leaps caused by the dead time effect. In addition, a capacitor voltage control strategy is proposed for the 5L-ANPC dc/dc converter to ensure the balanced flying capacitor voltage and desired five-level voltage waveforms. Finally, simulation and experimental studies...

  7. 75 FR 63040 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

    2010-10-14

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10... following new airworthiness directive (AD): 2010-21-13 McDonnell Douglas Corporation: Amendment 39-16473... November 18, 2010. Affected ADs (b) None. Applicability (c) This AD applies to McDonnell Douglas...

  8. 75 FR 68246 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

    2010-11-05

    ...-1044; Directorate Identifier 2010-NM-033-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas..., 2007) and adding the following new AD: McDonnell Douglas Corporation: Docket No. FAA-2010-1044.... Applicability (c) This AD applies to all McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

  9. Pulsewidth modulated DC-to-DC power conversion circuits, dynamics, and control designs

    Choi, Byungcho

    2013-01-01

    This is the definitive reference for anyone involved in pulsewidth modulated DC-to-DC power conversion Pulsewidth Modulated DC-to-DC Power Conversion: Circuits, Dynamics, and Control Designs provides engineers, researchers, and students in the power electronics field with comprehensive and complete guidance to understanding pulsewidth modulated (PWM) DC-to-DC power converters. Presented in three parts, the book addresses the circuitry and operation of PWM DC-to-DC converters and their dynamic characteristics, along with in-depth discussions of control design of PWM DC-to

  10. Atmel Microcontroller Based Soft Switched PWM ZVS Full Bridge DC to DC Converter

    DEEPAK KUMAR NAYAK

    2010-12-01

    Full Text Available This paper deals with the simulation and implementation of soft switched PWM ZVS full bridge DC to DC converter. The 48V DC is efficiently reduced to 12V DC using a DC to DC converter. This converter has advantages like reduced switching losses, stresses and EMI. Input DC is converted into high frequency AC and it is stepped down to 12V level. Later it is rectified using a full wave rectifier. Laboratory model of microcontroller based DC to DC converter is fabricated and tested. The experimental results are compared with the simulation results.

  11. 75 FR 60602 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

    2010-10-01

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10... adding the following new AD: 2010-20-14 McDonnell Douglas Corporation: Amendment 39-16449. Docket No. FAA... the airplanes identified in paragraphs (c)(1) and (c)(2) of this AD. (1) McDonnell Douglas Corporation...

  12. 75 FR 6160 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-15, DC...

    2010-02-08

    ...-0032; Directorate Identifier 2009-NM-213-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas...: McDonnell Douglas Corporation: Docket No. FAA-2010-0032; Directorate Identifier 2009-NM-213-AD. Comments Due... applies to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A...

  13. 75 FR 38943 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-10, DC-10-10F, DC-10-30, DC...

    2010-07-07

    ...-0672; Directorate Identifier 2010-NM-047-AD] RIN 2120-AA64 Airworthiness Directives; McDonnell Douglas...: McDonnell Douglas Corporation: Docket No. FAA-2010-0672; Directorate Identifier 2010-NM-047-AD. Comments Due... applies to McDonnell Douglas Corporation Model DC- 10-10, DC-10-10F, DC-10-30, DC-10-30F (KDC-10), DC-10...

  14. Light-weight DC to very high voltage DC converter

    Druce, R.L.; Kirbie, H.C.; Newton, M.A.

    1998-06-30

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current. 1 fig.

  15. Light-weight DC to very high voltage DC converter

    Druce, Robert L. (Union City, CA); Kirbie, Hugh C. (Dublin, CA); Newton, Mark A. (Livermore, CA)

    1998-01-01

    A DC-DC converter capable of generating outputs of 100 KV without a transformer comprises a silicon opening switch (SOS) diode connected to allow a charging current from a capacitor to flow into an inductor. When a specified amount of charge has flowed through the SOS diode, it opens up abruptly; and the consequential collapsing field of the inductor causes a voltage and current reversal that is steered into a load capacitor by an output diode. A switch across the series combination of the capacitor, inductor, and SOS diode closes to periodically reset the SOS diode by inducing a forward-biased current.

  16. Radiated electromagnetic emissions of DC-DC converters

    Feld, L; Jussen, R; Karpinski, W; Klein, K; Sammet, J; Wlochal, M

    2010-01-01

    For the CMS tracker at SLHC a new powering scheme is considered to be mandatory to allow the detector to provide at least the same performance as today at the LHC. The baseline solution of CMS foresees the use of DC-DC converters to provide larger currents with smaller losses. An important component of most converters are inductors which, however, tend to radiate the switching noise generated by the converter. The emissions of different inductors have been measured and simulated, the coil design has been optimized and noise susceptibility measurements, with present CMS hardware, have been performed. This article summarizes the results.

  17. Pulse-width modulated DC-DC power converters

    Kazimierczuk, Marian K

    2008-01-01

    This book studies switch-mode power supplies (SMPS) in great detail. This type of converter changes an unregulated DC voltage into a high-frequency pulse-width modulated (PWM) voltage controlled by varying the duty cycle, then changes the PWM AC voltage to a regulated DC voltage at a high efficiency by rectification and filtering. Used to supply electronic circuits, this converter saves energy and space in the overall system. With concept-orientated explanations, this book offers state-of-the-art SMPS technology and promotes an understanding of the principle operations of PWM converters,

  18. DESIGN OPTIMIZATION OF RESONANT DC-DC CONVERTERS

    Belqasem Aljafari

    2016-01-01

    Resonant DC/DC converters are the class of converters, which have L-C resonant tank serving as a major part of the power conversion process. The fundamental concept of the resonant converter is that the circulating energy in an L-C resonant circuit is manageable by changing the operating frequency, and therefore the converter can condition the input power to the desired output voltage. The development in power conversion technology is steady demand for high power efficiency and high power den...

  19. DC grid for home applications

    Elangovan, D.; Archana, R.; Jayadeep, V. J.; Nithin, M.; Arunkumar, G.

    2017-11-01

    More than fifty percent Indian population do not have access to electricity in daily lives. The distance between the power generating stations and the distribution centers forms one of the main reasons for lack of electrification in rural and remote areas. Here lies the importance of decentralization of power generation through renewable energy resources. In the present world, electricity is predominantly powered by alternating current, but most day to day devices like LED lamps, computers and electrical vehicles, all run on DC power. By directly supplying DC to these loads, the number of power conversion stages was reduced, and overall system efficiency increases. Replacing existing AC network with DC is a humongous task, but with power electronic techniques, this project intends to implement DC grid at a household level in remote and rural areas. Proposed work was designed and simulated successfully for various loads amounting to 250 W through appropriate power electronic convertors. Maximum utilization of the renewable sources for domestic and commercial application was achieved with the proposed DC topology.

  20. Linking DC together with TRSL

    Haxthausen, Anne; Yong, Xia

    1999-01-01

    In this talk we present a method for linking the Duration Calculus together with the Timed RAISE Specification Language. Duration Calculus (DC) [ZHR91] is an interval-based real time logic, which can be used naturally in capturing and eliciting users' real time requirements in the form of constra......In this talk we present a method for linking the Duration Calculus together with the Timed RAISE Specification Language. Duration Calculus (DC) [ZHR91] is an interval-based real time logic, which can be used naturally in capturing and eliciting users' real time requirements in the form.......TRSL is a real-time extension of the RAISE Specification Language (RSL) [Rlg92] which together with its associated method [Rmg95]and tools has shown to be very useful in the industrial development of software systems. Therefore, a promising approach for the development of real-time systemscould be to use DC...... for high-level specifications of real-time requirementsand TRSL for specifying real-time implementations in the form of timed communicating concurrent processes.In order to link DC and TRSL together in a well-founded way, we formally define what it means for a TRSL process to satisfy a DC requirement...

  1. Modeling and analysis of fractional order DC-DC converter.

    Radwan, Ahmed G; Emira, Ahmed A; AbdelAty, Amr M; Azar, Ahmad Taher

    2017-07-11

    Due to the non-idealities of commercial inductors, the demand for a better model that accurately describe their dynamic response is elevated. So, the fractional order models of Buck, Boost and Buck-Boost DC-DC converters are presented in this paper. The detailed analysis is made for the two most common modes of converter operation: Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM). Closed form time domain expressions are derived for inductor currents, voltage gain, average current, conduction time and power efficiency where the effect of the fractional order inductor is found to be strongly present. For example, the peak inductor current at steady state increases with decreasing the inductor order. Advanced Design Systems (ADS) circuit simulations are used to verify the derived formulas, where the fractional order inductor is simulated using Valsa Constant Phase Element (CPE) approximation and Generalized Impedance Converter (GIC). Different simulation results are introduced with good matching to the theoretical formulas for the three DC-DC converter topologies under different fractional orders. A comprehensive comparison with the recently published literature is presented to show the advantages and disadvantages of each approach. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  2. An Integrated Multifunctional Bidirectional AC/DC and DC/DC Converter for Electric Vehicles Applications

    Liwen Pan

    2016-06-01

    Full Text Available This paper presents an on-board vehicular battery charger that integrates bidirectional AC/DC converter and DC/DC converter to achieve high power density for application in electric vehicles (EVs. The integrated charger is able to transfer electrical energy between the battery pack and the electric traction system and to function as an AC/DC battery charger. The integrated charger topology is presented and the design of passive components is discussed. The control schemes are developed for motor drive system and battery-charging system with a power pulsation reduction circuit. Simulation results in MATLAB/Simulink and experiments on a 30-kW motor drive and 3.3-kW AC/DC charging prototype validate the performance of the proposed technology. In addition, power losses, efficiency comparison and thermal stress for the integrated charger are illustrated. The results of the analyses show the validity of the advanced integrated charger for electric vehicles.

  3. Switching coordination of distributed dc-dc converters for highly efficient photovoltaic power plants

    Agamy, Mohammed; Elasser, Ahmed; Sabate, Juan Antonio; Galbraith, Anthony William; Harfman Todorovic, Maja

    2014-09-09

    A distributed photovoltaic (PV) power plant includes a plurality of distributed dc-dc converters. The dc-dc converters are configured to switch in coordination with one another such that at least one dc-dc converter transfers power to a common dc-bus based upon the total system power available from one or more corresponding strings of PV modules. Due to the coordinated switching of the dc-dc converters, each dc-dc converter transferring power to the common dc-bus continues to operate within its optimal efficiency range as well as to optimize the maximum power point tracking in order to increase the energy yield of the PV power plant.

  4. Application of Distributed DC/DC Electronics in Photovoltaic Systems

    Kabala, Michael

    In a typical residential, commercial or utility grade photovoltaic (PV) system, PV modules are connected in series and in parallel to form an array that is connected to a standard DC/AC inverter, which is then connected directly to the grid. This type of standard installation; however, does very little to maximize the energy output of the solar array if certain conditions exist. These conditions could include age, temperature, irradiance and other factors that can cause mismatch between PV modules in an array that severely cripple the output power of the system. Since PV modules are typically connected in series to form a string, the output of the entire string is limited by the efficiency of the weakest module. With PV module efficiencies already relatively low, it is critical to extract the maximum power out of each module in order to make solar energy an economically viable competitor to oil and gas. Module level DC/DC electronics with maximum power point (MPP) tracking solves this issue by decoupling each module from the string in order for the module to operate independently of the geometry and complexity of the surrounding system. This allows each PV module to work at its maximum power point by transferring the maximum power the module is able to deliver directly to the load by either boosting (stepping up) the voltage or bucking (stepping down) the voltage. The goal of this thesis is to discuss the development of a per-module DC/DC converter in order to maximize the energy output of a PV module and reduce the overall cost of the system by increasing the energy harvest.

  5. Voltage Weak DC Distribution Grids

    Hailu, T.G.; Mackay, L.J.; Ramirez Elizondo, L.M.; Ferreira, J.A.

    2017-01-01

    This paper describes the behavior of voltage weak DC distribution systems. These systems have relatively small system capacitance. The size of system capacitance, which stores energy, has a considerable effect on the value of fault currents, control complexity, and system reliability. A number of

  6. Compact integrated dc SQUID gradiometer

    de Waal, V. J.; Klapwijk, T. M.

    1982-10-01

    An all-niobium integrated system of first-order gradiometer and dc suprconducting quantum interference device (SQUID) has been developed. It is relatively simple to fabricate, has an overall size of 17×12 mm and a sensitivity of 3.5×10-12 T m-1 Hz-1/2.

  7. Compact integrated dc SQUID gradiometer

    de Waal, V.J.; Klapwijk, T.M.

    1982-10-01

    An all-niobium integrated system of first-order gradiometer and dc suprconducting quantum interference device (SQUID) has been developed. It is relatively simple to fabricate, has an overall size of 17 x 12 mm and a sensitivity of 3.5 x 10/sup -12/ T m/sup -1/ Hz/sup -1/2/.

  8. Experiments with a DC Motor

    Kraftmakher, Yaakov

    2010-01-01

    Experiments with an electric motor provide good opportunity to demonstrate some basic laws of electricity and magnetism. The aim of the experiments with a low-power dc motor is to show how the motor approaches its steady rotation and how its torque, mechanical power and efficiency depend on the rotation velocity. The tight relationship between the…

  9. Borehole DC-6 hydrostratigraphic chart

    Gephart, R.E.

    1981-09-01

    This hydrostratigraphic chart for Borehole DC-6 identifies the basic stratigraphy and preliminary hydrologic test results. This borehole was cored for obtaining stratigraphic data and only that portion within the Grande Ronde formation remains open for hydrologic testing. The upper two formations were cased and cemented off

  10. DC motor operation controlled from a DC/DC power converter in pulse mode with low duty cycle

    Stefanov, Goce; Kukuseva, Maja; Citkuseva Dimitrovska, Biljana

    2016-01-01

    In this paper pulse mode of operation of DC motor controlled by DC/DC power converter is analyzed. DC motor operation with time intervals in which the motor operates without output load is of interest. In this mode it is possible the motor to restore energy. Also, in the paper are represented calculations for the amount of the restored energy in the pulse mode operation of the motor for different duty cycles.

  11. DC to DC power converters and methods of controlling the same

    Steigerwald, Robert Louis; Elasser, Ahmed; Sabate, Juan Antonio; Todorovic, Maja Harfman; Agamy, Mohammed

    2012-12-11

    A power generation system configured to provide direct current (DC) power to a DC link is described. The system includes a first power generation unit configured to output DC power. The system also includes a first DC to DC converter comprising an input section and an output section. The output section of the first DC to DC converter is coupled in series with the first power generation unit. The first DC to DC converter is configured to process a first portion of the DC power output by the first power generation unit and to provide an unprocessed second portion of the DC power output of the first power generation unit to the output section.

  12. Analysis of a high power, resonant DC-DC converter for DC wind turbines

    Dincan, Catalin Gabriel; Kjær, Philip Carne; Chen, Yu-Hsing

    2018-01-01

    This paper is introducing a new method of operation for a series resonant converter, with intended application in megawatt high-voltage DC wind turbines. Compared to a frequency controlled series resonant converter operated in sub resonant mode, the method (entitled pulse removal technique) allows...

  13. Dilation and Curettage (D&C)

    ... For Patients About ACOG Dilation and Curettage (D&C) Home For Patients Search FAQs Dilation and Curettage ( ... February 2016 PDF Format Dilation and Curettage (D&C) Special Procedures What is dilation and curettage (D& ...

  14. Hierarchical Power Sharing Control in DC Microgrids

    Peyghami, Saeed; Mokhtari, Hossein; Blaabjerg, Frede

    2016-01-01

    Because of the advances in power electronics, DC-based power systems, have been used in industrial applications such as data centers [18], space applications [10], aircraft [12], offshore wind farms, electric vehicles [56], DC home systems [5, 20], and high-voltage DC transmission systems...

  15. Characterising and modelling extended conducted electromagnetic interference in densely packed DC-DC converter

    Grobler, Inus

    2013-09-01

    Full Text Available . The military specified DC-DC converters are applicable, spanning from 100 W handheld power managers up to 2 kW DC-DC battery chargers. Circuit layout high frequency effects as well as high frequency impedances of the power components were characterised...

  16. Full wave dc-to-dc converter using energy storage transformers

    Moore, E. T.; Wilson, T. G.

    1969-01-01

    Full wave dc-to-dc converter, for an ion thrustor, uses energy storage transformers to provide a method of dc-to-dc conversion and regulation. The converter has a high degree of physical simplicity, is lightweight and has high efficiency.

  17. A DC-DC Conversion Powering Scheme for the CMS Phase-1 Pixel Upgrade

    Feld, Lutz Werner; Marcel Friedrichs; Richard Hensch; Karpinski, Waclaw; Klein, Katja; Sammet, Jan Domenik; Wlochal, Michael

    2012-01-01

    The powering scheme of the CMS pixel detector will be described, and the performance of prototype DC-DC buck converters will be presented, including power efficiency, system tests with DC-DC converters and pixel modules, thermal management, reliability at low temperature, and studies of potential frequency locking betwe...

  18. Characterization of phenolic compounds in Helichrysum melaleucum by high-performance liquid chromatography with on-line ultraviolet and mass spectrometry detection.

    Gouveia, Sandra C; Castilho, Paula C

    2010-07-15

    Helicrysum melaleucum is a medicinal plant traditionally used in the islands of the Macaronesia region for the treatment of respiratory diseases. In this work, the phenolic compounds of Helicrysum melaleucum plants collected in different geographical locations of Madeira Island and their morphological parts (total aerial parts, leaves, flowers and stems) were extracted and analyzed separately by high-performance liquid chromatography/electrospray ionization tandem mass spectrometry (HPLC-DAD/ESI-MS(n)). A total of 68 compounds were characterized based mainly on their UV and mass spectra. These included derivatives of O-glycosylated flavonoids (flavonol and flavones type), quinic acid, caffeic acid, lignans and polyphenols. The flowers were found to be the morphological part with higher variety of phenolic compounds. The large differences in the phenolic composition of plants collected from different geographical locations allowed the identification of a few components, such as pinoresinol and methoxylated flavone derivatives, likely to be useful as geographical markers. Also, these results promote further comparison of the bioactivities of the different samples analyzed. This paper marks the first report on the chemical analysis of Helichrysum melaleucum species. Copyright 2010 John Wiley & Sons, Ltd.

  19. Evaluation of the antioxidant and cytotoxic activity of arzanol, a prenylated alpha-pyrone-phloroglucinol etherodimer from Helichrysum italicum subsp.microphyllum.

    Rosa, Antonella; Deiana, Monica; Atzeri, Angela; Corona, Giulia; Incani, Alessandra; Melis, M Paola; Appendino, Giovanni; Dessì, M Assunta

    2007-01-30

    Various phenolics and (mero)terpenoids from Helichrysum italicum subsp. microphyllum, a plant endemic to Sardinia, were investigated for their capacity to inhibit non-enzymatic lipid peroxidation. These compounds were studied in simple in vitro systems, under conditions of autoxidation and of iron (EDTA)-mediated oxidation of linoleic acid at 37 degrees C. Arzanol, a pyrone-phloroglucinol etherodimer, and helipyrone, a dimeric pyrone, showed antioxidant activity, and could protect linoleic acid against free radical attack in assays of autoxidation and EDTA-mediated oxidation. Methylarzanol, as well as the sesquiterpene alcohol rosifoliol, showed a decreased, but still significant, protective effect against linoleic acid oxidation. Arzanol and helipyrone were also tested in an assay of thermal (140 degrees C) autoxidation of cholesterol, where arzanol showed significant antioxidant activity. The cytotoxicity of arzanol was further evaluated in VERO cells, a line of fibroblasts derived from monkey kidney. Arzanol, at non-cytotoxic concentrations, showed a strong inhibition of TBH-induced oxidative stress in VERO cells. The results of the present work suggest that the natural compound arzanol exerts useful antioxidant properties in different in vitro systems of lipid peroxidation.

  20. Contribution to the analysis of the essential oil of Helichrysum italicum (Roth) G. Don. Determination of ester bonded acids and phenols.

    Mastelić, Josip; Politeo, Olivera; Jerković, Igor

    2008-04-07

    The essential oil of Helichrysum italicum (Roth) G. Don (everlasting or Immortelle essential oil) was isolated by hydrodistillation and analysed by GC and GCMS. Forty four compounds were identified. The main components were alpha-pinene(12.8%), 2-methyl-cyclohexyl pentanoate (11.1 %), neryl acetate (10.4%), 1,7-di-epi-alpha-cedrene (6.8%) and other compounds. The oil was fractionated and ester-containing fraction was hydrolysed with KOH/H(2)SO(4). The liberated volatiles were analysed by GC and GC-MS: three phenols and twenty seven volatile carboxylic acids were identified[70% low fatty acids (C(2)-C(5)), 15% C(10)-C(12) acids and 15% other acids]. The main acids were acetic acid (24.3%) propanoic acid (17.2%), 2-methylpropanoic acid (11.4%),dodecanoic acid (8.7%), 2-methylbutanoic acid (8.3%), (Z)-2-methylbutenoic acid(5.1%) and decanoic acid (4.6%). With respect to the identified bonded carboxylic acids,the minimal number of esters in the oil was twenty seven, but their overall quantity was probably larger due to different possible combinations of alcohols with acids to form esters. On the other hand, only six main esters were identified in the oil before fractionation and hydrolysis.

  1. Contribution to the Analysis of the Essential Oil of Helichrysum italicum (Roth G. Don. – Determination of Ester Bonded Acids and Phenols

    Igor Jerković

    2008-04-01

    Full Text Available The essential oil of Helichrysum italicum (Roth G. Don (everlasting orImmortelle essential oil was isolated by hydrodistillation and analysed by GC and GCMS.Forty four compounds were identified. The main components were α-pinene(12.8%, 2-methyl-cyclohexyl pentanoate (11.1 %, neryl acetate (10.4%, 1,7-di-epi-α-cedrene (6.8% and other compounds. The oil was fractionated and ester-containingfraction was hydrolysed with KOH/H2SO4. The liberated volatiles were analysed by GCand GC-MS: three phenols and twenty seven volatile carboxylic acids were identified[70% low fatty acids (C2-C5, 15% C10-C12 acids and 15% other acids]. The main acidswere acetic acid (24.3% propanoic acid (17.2%, 2-methylpropanoic acid (11.4%,dodecanoic acid (8.7%, 2-methylbutanoic acid (8.3%, (Z-2-methylbutenoic acid(5.1% and decanoic acid (4.6%. With respect to the identified bonded carboxylic acids,the minimal number of esters in the oil was twenty seven, but their overall quantity wasprobably larger due to different possible combinations of alcohols with acids to formesters. On the other hand, only six main esters were identified in the oil beforefractionation and hydrolysis.

  2. Transformerless dc-Isolated Converter

    Rippel, Wally E.

    1987-01-01

    Efficient voltage converter employs capacitive instead of transformer coupling to provide dc isolation. Offers buck/boost operation, minimal filtering, and low parts count, with possible application in photovoltaic power inverters, power supplies and battery charges. In photovoltaic inverter circuit with transformerless converter, Q2, Q3, Q4, and Q5 form line-commutated inverter. Switching losses and stresses nil because switching performed when current is zero.

  3. AC-DC PFC Converter Using Combination of Flyback Converter and Full-bridge DC-DC Converter

    Moh. Zaenal Efendi

    2014-06-01

    Full Text Available This paper presents a combination of power factor correction converter using Flyback converter and Full-bridge dc-dc converter in series connection. Flyback converter is operated in discontinuous conduction mode so that it can serve as a power factor correction converter and meanwhile Full-bridge dc-dc converter is used for dc regulator. This converter system is designed to produce a 86 Volt of output voltage and 2 A of output current. Both simulation and experiment results show that the power factor of this converter achieves up to 0.99 and meets harmonic standard of IEC61000-3-2. Keywords: Flyback Converter, Full-bridge DC-DC Converter, Power Factor Correction.

  4. A Feed-Forward Control Realizing Fast Response for Three-Branch Interleaved DC-DC Converter in DC Microgrid

    Haojie Wang

    2016-07-01

    Full Text Available It is a common practice for storage batteries to be connected to DC microgrid buses through DC-DC converters for voltage support on islanded operation mode. A feed-forward control based dual-loop constant voltage PI control for three-branch interleaved DC-DC converters (TIDC is proposed for storage batteries in DC microgrids. The working principle of TIDC is analyzed, and the factors influencing the response rate based on the dual-loop constant voltage control for TIDC are discussed, and then the method of feed-forward control for TIDC is studied to improve the response rate for load changing. A prototype of the TIDC is developed and an experimental platform is built. The experiment results show that DC bus voltage sags or swells caused by load changing can be reduced and the time for voltage recovery can be decreased significantly with the proposed feed-forward control.

  5. A Feed-Forward Control Realizing Fast Response for Three-Branch Interleaved DC-DC Converter in DC Microgrid

    Wang, Haojie; Han, Minxiao; Yan, Wenli

    2016-01-01

    It is a common practice for storage batteries to be connected to DC microgrid buses through DC-DC converters for voltage support on islanded operation mode. A feed-forward control based dual-loop constant voltage PI control for three-branch interleaved DC-DC converters (TIDC) is proposed...... for storage batteries in DC microgrids. The working principle of TIDC is analyzed, and the factors influencing the response rate based on the dual-loop constant voltage control for TIDC are discussed, and then the method of feed-forward control for TIDC is studied to improve the response rate for load...... changing. A prototype of the TIDC is developed and an experimental platform is built. The experiment results show that DC bus voltage sags or swells caused by load changing can be reduced and the time for voltage recovery can be decreased significantly with the proposed feed-forward control....

  6. FLYWHEEL AND A DC MACHINE

    IVAN ALCALÁ

    2014-01-01

    Full Text Available Este artículo describe el análisis, modelado y simulación de un vehículo eléctrico (EV enfocado al desarrollo de un banco de pruebas para reproducir la dinámica del EV. El banco está formado por un drive de motor de inducción (IM acoplado directamente a una máquina de DC y a un volante de inercia a través de una transmisión. El volante de inercia y la máquina de DC reproducen la dinámica y las fuerzas que actúan en el vehículo. Se propone una metodología para diseñar un banco de pruebas de EV para estudiar el comportamiento de vehículos eléctricos cercano a las condiciones de operación reales. El análisis de las fuerzas en el EV en conjunto con la máquina DC define las condiciones de operación del EV. El modelado y la simulación son desarrollados en MATLAB/Simulink, el banco de pruebas implementado es controlado por un DSP. Finalmente, los resultados de simulación y experimentales obtenidos validan el funcionamiento del banco de prueba.

  7. Quasi-Z-Source Half-Bridge DC-DC Converter for Photovoltaic Applications

    Vinnikov, D; Chub, A; Husev, O; Zaķis, J

    2015-01-01

    This paper presents a novel quasi-Z-source halfbridge galvanically isolated DC-DC converter intended for the photovoltaic applications. The topology could be envisioned as an alternative to the boost half-bridge DC-DC converter but the benefit of its symmetric structure reduces the threat of transformer saturation due to the dc flux. The proposed converter features the continuous input current and could be used either with one or two input voltage sources.

  8. Control of the DC-DC Converter used into Energy Generation System

    Bizon, Nicu; Oproescu, Mihai

    2006-01-01

    This paper presents an investigation of the DC-DC Converter controller used into Energy Generation System. The full bridge is used into an Energy Generation System (EGS) as second power interface between the energy source and the high DC bus. The simulation results show that the DC-DC Converter behavior can be improved using a well designed PI control surface. The used Simulink models for the EGS blocks and some design considerations are presented, too. (authors)

  9. ZVS Operating Region of Multiresonant DC/DC Boost Conveter

    Elzbieta Szychta

    2007-01-01

    Full Text Available Electromagnetic phenomena that occur during stable operation in resonant circuits of multiresonant ZVS boost converter are described, which can be applied in many fields of the needs of DC voltage electricity. The operating region of the converter is defined which assures the circuit’s operation in which semiconductor elements are switched at zero voltage (ZVS. Conditions delimiting the ZVS operating region are provided. Analysis of the circuit’s operation is based on results of simulation testing by means of Simplorer software.

  10. A Feedback Passivation Design for DC Microgrid and Its DC/DC Converters

    Feifan Ji

    2016-12-01

    Full Text Available There are difficulties in analyzing the stability of microgrids since they are located on various network structures. However, considering that the network often consists of passive elements, the passivity theory is applied in this paper to solve the above-mentioned problem. It has been formerly shown that when the network is weakly strictly positive real (WSPR, the DC microgrid is stable if all interfaces between the microgrid and converters are made to be passive, which is called interface passivity. Then, the feedback passivation method is proposed for the controller design of various DC–DC converters to achieve the interface passivity. The interface passivity is different from the passivity of closed-loop systems on which the passivity based control (PBC concentrates. The feedback passivation design is detailed for typical buck converters and boost converters in terms of conditions that the controller parameters should satisfy. The theoretical results are verified by a hardware-in-loop real-time labotray (RTLab simulation of a DC microgrid with four generators.

  11. Artificial neural network control of sab dc/dc converter

    Mahar, M.A.; Abro, M.R.; Larik, A.S.

    2009-01-01

    The latest development of power semiconductor devices enable the modern power electronic converters to withstand high voltage and high power applications. Power electronic converters are mostly periodic variable structure systems due to their switched operations. The main drawback of these converters is the generation of oscillations which are developed during the operation of the converters under nonlinear situations. To handle these nonlinearities, various researchers have proposed different control techniques. Power electronic designers are devoting in the further development of converter topologies and their control techniques. SAB (Single Active Bridge) DC/DC converter is a new topology recently introduced by Demetriades. This topology is used in high voltage and high power applications. Because of its smart features, SAB converter has recently drawn attention of many researchers. However, during the operation of SAB converter severe oscillations are generated. In this research work, a novel NNC (Neural Network Controller) model is developed for SAB converter to minimize oscillations generated during its operation. NNC is believed to be an advanced nonlinear and robust controller which has the ability to map the nonlinear behaviour in a negligible response time. The performance of SAB converter with NNC is tested under dynamic region by considering the reference voltage variation and duty ratio variation. The SAB converter is implemented and simulated in MATLAB/Simulink. The simulated results are presented. (author)

  12. Experiments with a dc motor

    Kraftmakher, Yaakov

    2010-01-01

    Experiments with an electric motor provide good opportunity to demonstrate some basic laws of electricity and magnetism. The aim of the experiments with a low-power dc motor is to show how the motor approaches its steady rotation and how its torque, mechanical power and efficiency depend on the rotation velocity. The tight relationship between the mechanical and electrical parameters of the motor is clearly seen. The measurements are carried out with the ScienceWorkshop data-acquisition system and the DataStudio software from PASCO scientific. The experiments are well related to university courses of electricity and magnetism and can be used in undergraduate laboratories or for lecture demonstrations.

  13. Using PBL to Improve Educational Outcomes and Student Satisfaction in the Teaching of DC/DC and DC/AC Converters

    Martinez-Rodrigo, Fernando; Herrero-De Lucas, Luis Carlos; de Pablo, Santiago; Rey-Boue, Alexis B.

    2017-01-01

    This paper examines the question of how to use project-based learning to increase student performance and satisfaction in a power electronics course addressing the topics of dc/dc and dc/ac converters, the assembly of a dc/dc converter, and the use of a commercial speed drive. A detailed presentation of the methodology is shown, and the results…

  14. Hierarchical Velocity Control Based on Differential Flatness for a DC/DC Buck Converter-DC Motor System

    R. Silva-Ortigoza

    2014-01-01

    Full Text Available This paper presents a hierarchical controller that carries out the angular velocity trajectory tracking task for a DC motor driven by a DC/DC Buck converter. The high level control is related to the DC motor and the low level control is dedicated to the DC/DC Buck converter; both controls are designed via differential flatness. The high level control provides a desired voltage profile for the DC motor to achieve the tracking of a desired angular velocity trajectory. Then, a low level control is designed to ensure that the output voltage of the DC/DC Buck converter tracks the voltage profile imposed by the high level control. In order to experimentally verify the hierarchical controller performance, a DS1104 electronic board from dSPACE and Matlab-Simulink are used. The switched implementation of the hierarchical average controller is accomplished by means of pulse width modulation. Experimental results of the hierarchical controller for the velocity trajectory tracking task show good performance and robustness against the uncertainties associated with different system parameters.

  15. The Topologies Research of a Soft Switching Bidirectional DC/DC Converter

    Zhang, Qi; Zhang, Yongping; Sun, Xiangdong

    2017-01-01

    A soft-switching solution implemented to the traditional bidirectional DC/DC converter is developed. The soft-switching cell, which composed of three auxiliary switches, one resonant capacitor and one resonant inductor, is equipped in the traditional bidirectional DC/DC converter to realize circuit...... circle. And the proposed topology of bidirectional soft-switching dc-dc converter(TASBC) performs ideal soft switching at boost operations. The characteristics of the proposed converter has been verified by MATLAB simulations and experimental results....

  16. Elimination of output voltage oscillations in DC-DC converter using PWM with PI controller

    Sreenivasappa Veeranna Bhupasandra

    2010-01-01

    Full Text Available In this paper the SIMULINK model of a PWM controlled DC-DC converter is modeled using switching function concept to control the speed of the DC motor. The presence of the voltage oscillation cycles due to higher switching frequency in the DC-DC converter is identified. The effect of these oscillations on the output voltage of the converter, Armature current, Developed torque and Speed of the DC motor is analyzed. In order to minimize the oscillation cycles the PI controller is proposed in the PWM controller.

  17. Chaos analysis and chaotic EMI suppression of DC-DC converters

    Zhang, Bo

    2014-01-01

    Introduces chaos theory, its analytical methods and the means to apply chaos to the switching power supply design DC-DC converters are typical switching systems which have plenty of nonlinear behaviors, such as bifurcation and chaos. The nonlinear behaviors of DC-DC converters have been studied heavily over the past 20 years, yet researchers are still unsure of the practical application of bifurcations and chaos in switching converters. The electromagnetic interference (EMI), which resulted from the high rates of changes of voltage and current, has become a major design criterion in DC-DC co

  18. Anti-atherosclerotic activities of flavonoids from the flowers of Helichrysum arenarium L. MOENCH through the pathway of anti-inflammation.

    Mao, Zhonghua; Gan, Chunli; Zhu, Jiuxin; Ma, Nan; Wu, Lijun; Wang, Libo; Wang, Xiaobo

    2017-06-15

    We have successfully established AS model using thoracic aortas vascular ring which evaluated by the morphological changes of blood vessels, the proliferation of VSMC, and the expression of inflammation factors VEGF, CRP, JNK2 and p38. This AS model has the advantages of low cost, convenient and short period of established time. Moreover, we investigated the anti-AS activities of 7 flavonoids Narirutin (1), Naringin (2), Eriodictyol (3), Luteolin (4), Galuteolin (5), Astragalin (6), Kaempferol (7) from flowers of Helichrysum arenarium L. MOENCH by examining the vascular morphology, the inhibition on the expression of inflammation factors CRP, VEGF, JNK2, p38. In addition, we investigated the anti-AS activities of these 7 flavonoids by examining NO secretion of RAW264.7 cells in response to LPS. All above inflammation factors have been proved to be involved in the formation of AS. After comprehensive analysis of all results to discuss the structure-activity relationship, we summarized the conclusions at follow: compounds 1-7 could inhibit the expression of VEGF, CRP, JNK2, p38 and NO at different level, and we evaluated that flavonol aglycone have more significant anti-inflammation than it's glycoside, and the anti-AS activity of flavonols were stronger than flavanones and flavones, which means that 3-group might be the effective group. Eventually, we supposed the main anti-inflammatory mechanism of these compounds was to reduce the expression of CRP, inhibit the kinases activity of JNK2 and p38, and then the MAPK pathway was suppressed, which resulted in the decrease of NO synthesis, VEGF expression and endothelial adhesion factor expression. And eventually, the scar tissue and vascular stenosis formations were prevented. This conclusion suggested flavonoids have the potential of preventing AS formation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Simultaneous distribution of AC and DC power

    Polese, Luigi Gentile

    2015-09-15

    A system and method for the transport and distribution of both AC (alternating current) power and DC (direct current) power over wiring infrastructure normally used for distributing AC power only, for example, residential and/or commercial buildings' electrical wires is disclosed and taught. The system and method permits the combining of AC and DC power sources and the simultaneous distribution of the resulting power over the same wiring. At the utilization site a complementary device permits the separation of the DC power from the AC power and their reconstruction, for use in conventional AC-only and DC-only devices.

  20. Drilling history core hole DC-8

    1978-10-01

    Core hole DC-8 was completed in August, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Scisson, Inc. furnished the engineering, daily supervision of the core drilling activities, and geologic core logging for hole DC-8. Core hole DC-8 is located on the Hanford Site near the Wye Barricade and 50 feet northwest of rotary hole DC-7. The Hanford Site vation coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 mean sea level. The purpose of core hole DC-8 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing and cross-hole seismic shear and pressure wave velocity studies with rotary hole DC-7. The total depth of core hole DC-8 was 4100.5 feet. Core recovery exceeded 97 percent of the total footage cored

  1. Drilling history core hole DC-8

    1978-10-01

    Core hole DC-8 was completed in August, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Scisson, Inc. furnished the engineering, daily supervision of the core drilling activities, and geologic core logging for hole DC-8. Core hole DC-8 is located on the Hanford Site near the Wye Barricade and 50 feet northwest of rotary hole DC-7. The Hanford Site vation coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 coordinates for DC-8 are North 14,955.94 feet and West 14,861.92 mean sea level. The purpose of core hole DC-8 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing and cross-hole seismic shear and pressure wave velocity studies with rotary hole DC-7. The total depth of core hole DC-8 was 4100.5 feet. Core recovery exceeded 97 percent of the total footage cored.

  2. Wide Temperature Range DC-DC Boost Converters for Command/Control/Drive Electronics, Phase I

    National Aeronautics and Space Administration — We shall develop wide temperature range DC-DC boost converters that can be fabricated using commercial CMOS foundries. The boost converters will increase the low...

  3. Modular Power System Configured with Standard Product Hybrid DC-DC Converters, Phase II

    National Aeronautics and Space Administration — VPT proposes an innovative concept whereby complex NASA space power electronic systems can be configured using a small number of qualified hybrid DC-DC converter and...

  4. Development of a DC-DC conversion powering scheme for the CMS Phase-1 pixel upgrade

    Feld, Lutz Werner; Karpinski, Waclaw; Klein, Katja; Lipinski, Martin; Preuten, Marius; Max Rauch; Rittich, David Michael; Sammet, Jan Domenik; Wlochal, Michael

    2014-01-01

    A novel powering scheme based on the DC-DC conversion technique will be exploited to power the CMS Phase-1 pixel detector. DC-DC buck converters for the CMS pixel project have been developed, based on the AMIS5 ASIC designed by CERN. The powering system of the Phase-1 pixel detector is described and the performance of the converter prototypes is detailed, including power efficiency, stability of the output voltage, shielding, and thermal management. Results from a test of the magnetic field tolerance of the DC-DC converters are reported. System tests with pixel modules using many components of the future pixel barrel system are summarized. Finally first impressions from a pre-series of 200 DC-DC converters are presented.

  5. DIAGNOSTIC/PROGNOSTIC EXPERIMENTS FOR CAPACITOR DEGRADATION AND HEALTH MONITORING IN DC-DC CONVERTERS

    National Aeronautics and Space Administration — Studying and analyzing the ageing mechanisms of electronic components avionics in systems such as the GPS and INAV are of critical importance. In DC-DC power...

  6. Digitally intensive DC-DC converter for extreme space environments, Phase I

    National Aeronautics and Space Administration — The Space Micro –Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator core...

  7. Digitally intensive DC-DC converter for extreme space environments, Phase II

    National Aeronautics and Space Administration — The Space Micro-Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator core...

  8. 75 FR 61352 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-10-30, DC-10-30F, DC-10-30F (KC...

    2010-10-05

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 10-30, DC-10-30F, DC-10-30F (KC-10A and KDC-10...-13 McDonnell Douglas Corporation: Amendment 39-16448; Docket No. FAA-2010-0553; Directorate.... Applicability (c) This AD applies to McDonnell Douglas Corporation Model DC- 10-30, DC-10-30F, DC-10-30F (KC-10A...

  9. 75 FR 27401 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-30, DC-9-40, and DC-9-50...

    2010-05-17

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 9-30, DC-9-40, and DC-9-50 Series Airplanes... airworthiness directive (AD) for certain Model DC-9-30, DC-9-40, and DC-9-50 series airplanes. This AD requires... this AD to detect and correct the potential for an arc/spark condition to occur within the fuel boost...

  10. Novel composite resonance DC-DC converter with voltage doubler rectifier

    Kato, Hisatsugu; Matsuo, Hirohumi; Eguchi, Masaki; Sakamoto, Yukitaka; Nakaishi, Masaki

    2009-01-01

    This paper deals with a novel composite resonance DC-DC converter with the voltage doubler rectifier, which is developed to be applied to the power conditioner of the photovoltaic generation system. The proposed DC-DC converter has the current and voltage resonance functions. Therefore, the output voltage regulation can be achieved for the large variations of the input voltage and load. Also, this converter has the high power efficiency. The maximum power efficiency 96.1% can be realized.

  11. Regulation of DC development and DC-mediated T-cell immunity via CISH

    Miah, Mohammad Alam; Bae, Yong-Soo

    2013-01-01

    Cytokine inducible SH2-containing protein (CISH) plays a crucial role in type 1 dendritic cell (DC) development as well as in the DC-mediated activation of cytotoxic T lymphocytes (CTLs). CISH expression at late DC developmental stages shuts down the proliferation of DC progenitors by negatively regulating signal transducer and activator of transcription 5 (STAT5) and facilitates the differentiation of DCs into potent stimulators of CTLs.

  12. Regulation of DC development and DC-mediated T-cell immunity via CISH.

    Miah, Mohammad Alam; Bae, Yong-Soo

    2013-03-01

    Cytokine inducible SH2-containing protein (CISH) plays a crucial role in type 1 dendritic cell (DC) development as well as in the DC-mediated activation of cytotoxic T lymphocytes (CTLs). CISH expression at late DC developmental stages shuts down the proliferation of DC progenitors by negatively regulating signal transducer and activator of transcription 5 (STAT5) and facilitates the differentiation of DCs into potent stimulators of CTLs.

  13. Design and Analysis of Two-Phase Boost DC-DC Converter

    Taufik Taufik; Tadeus Gunawan; Dale Dolan; Makbul Anwari

    2010-01-01

    Multiphasing of dc-dc converters has been known to give technical and economical benefits to low voltage high power buck regulator modules. A major advantage of multiphasing dc-dc converters is the improvement of input and output performances in the buck converter. From this aspect, a potential use would be in renewable energy where power quality plays an important factor. This paper presents the design of a 2-phase 200W boost converter for battery charging application. Analysis of results fr...

  14. A Fixed-Frequency Bidirectional Resonant DC-DC Converter Suitable for Wide Voltage Gain Range

    Shen, Yanfeng; Wang, Huai; Blaabjerg, Frede

    2017-01-01

    This paper proposes a new bidirectional resonant dc-dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant DC-DC converters, and meanwhile achieves high efficiency...... and characteristics of the proposed converter are analyzed. Finally, a 1-kW converter prototype is built and the experimental results verify the theoretical analyses....

  15. Development of a green mode DC/DC converter available to portable nuclear instrument

    Gao Feiyan; Wu Longxiong; Tan Wei; Tang Yaogeng

    2010-01-01

    A green mode DC/DC converter was developed which suitable to the portable nuclear instrument which is powered by battery and is sometime at stand-by mode. Some updated control approaches such as pseudo-resonant type power supply control and synchronous rectification were adopted to makethe DC/DC converter operate with low power consumption and high efficiency. The test results the battery can be prolonged with this converter. (authors)

  16. Superconducting dc fault current limiter

    Cointe, Y.

    2007-12-01

    Within the framework of the electric power market liberalization, DC networks have many interests compared to alternative ones, but their protections need to use new systems. Superconducting fault current limiters enable by an overstepping of the critical current to limit the fault current to a preset value, lower than the theoretical short-circuit current. For these applications, coated conductors offer excellent opportunities. We worked on the implementation of these materials and built a test bench. We carried out limiting experiments to estimate the quench homogeneity at various short-circuit parameters. An important point is the temperature measurement by deposited sensors on the ribbon, results are in good correlation with the theoretical models. Improved quench behaviours for temperatures close to the critical temperature have been confirmed. Our results enable to better understand the limitation mechanisms of coated conductors. (author)

  17. The possibility of detecting DC

    Witte, N.S.; Brown, R.D.

    1977-01-01

    IRC + 10216, a bright infrared late type carbon star, is observed to have millimetre range line emission of the species 12 CO, 13 CO, CS, C 2 H, HC 3 N, CN, HCN, SiS and SiO in an extended envelope around the central infrared sources. A model explaining the line emission in terms of infrared pumping between the two lowest vibrational levels, first proposed for IRC + 10216, was used to calculate antenna temperatures for various rotational transitions of HC 3 N; since there is a prima facie agreement between the calculated and observed values for HC 3 N we have attempted the same calculation for DC 3 N. (J.R.)

  18. Superconducting energy stabilizer with charging and discharging DC-DC converters

    Kim, S.H.; Kostecki, E.L.; DeWinkel, C.C.

    1992-01-01

    This patent describes a superconducting energy stabilizer having multiple load connections and employing DC-DC conversion for storing energy in a superconducting inductive energy storage device having a first end and a second end, and for releasing the stored energy from the superconducting inductive energy storage device to a load or loads or to a utility or an industrial electrical distribution system, the superconducting energy stabilizer having multiple load connections and employing DC-DC conversion. It comprises: energy storage cell means for supplying energy to the load, discharging DC-DC converter means for releasing energy from the superconducting inductive energy storage device to the energy storage cell means, the discharging DC-DC converter means having input terminals, output terminals, and a discharging control line means for carrying signals controlling the operation of the discharging DC-DC converter means, one of the input terminals of the discharging DC-DC converter means coupled to the first end of the superconducting energy storage device

  19. Dual wound dc brush motor gearhead

    Henson, Barrie W.

    1986-01-01

    The design requirements, the design, development tests and problems, the qualification and life test and the findings of the strip examination of a dual wound DC brushed motor gearhead are described. It is the only space qualified dual wound dc brushed motor gearhead in Europe.

  20. Electronic DC transformer with high power density

    Pavlovský, M.

    2006-01-01

    This thesis is concerned with the possibilities of increasing the power density of high-power dc-dc converters with galvanic isolation. Three cornerstones for reaching high power densities are identified as: size reduction of passive components, reduction of losses particularly in active components

  1. DC/DC converters for integration of double-layer condensers in onboard power supply; DC/DC-Wandler zur Einbindung von Doppelschichtkondensatoren in das Fahrzeugenergiebordnetz

    Polenov, Dieter

    2010-01-15

    The paper discusses DC/DC converters for integration of double layer condensers into the onboard power system. First, requirements on DC/DC converters are listed and compared on the basis of three exemplary applications. A DC/DC converter concept is developed for decoupling transient high-power loads like electric steering systems. Three different topologies are compared using a specially developed method in order to find the best solution for the given application. In order to establish adequate criteria for selecting the switching frequency and inductivities of storage throttles, the influence of the trottle power change on the switching characteristics of the MOSFETs and on certain ranges of EMP interference emissions is investigated. As methods of optimising the operation of the synchronous rectifiers, parallel connection of Schottky diodes and synchronous rectifiers as well as the variation of the shut-off dead times of synchronous rectifiers were investigated. Further, a concept for converter control was developed in consideration of the intended application and topology. Finally, selected aspects for implementation of the DC/DC converter concept are presented as well as the results of experimental investigations.

  2. Modelling of flow phenomena during DC casting

    Zuidema, J.

    2005-01-01

    Modelling of Flow Phenomena during DC Casting Jan Zuidema The production of aluminium ingots, by semi-continuous casting, is a complex process. DC Casting stands for direct chill casting. During this process liquid aluminium transforms to solid aluminium while cooling down. This is not an

  3. DC KIDS COUNT e-Databook Indicators

    DC Action for Children, 2012

    2012-01-01

    This report presents indicators that are included in DC Action for Children's 2012 KIDS COUNT e-databook, their definitions and sources and the rationale for their selection. The indicators for DC KIDS COUNT represent a mix of traditional KIDS COUNT indicators of child well-being, such as the number of children living in poverty, and indicators of…

  4. A Component-Reduced Zero-Voltage Switching Three-Level DC-DC Converter

    Qin, Zian; Pang, Ying; Wang, Huai

    2016-01-01

    The basic Zero-Voltage Switching (ZVS) three-level DC-DC converter has one clamping capacitor to realize the ZVS of the switches, and two clamping diodes to clamp the voltage of the clamping capacitor. In order to reduce the reverse recovery loss of the diode as well as its cost, this paper...... proposes to remove one of the clamping diodes in basic ZVS three-level DC-DC converter. With less components, the proposed converter can still have a stable clamping capacitor voltage, which is clamped at half of the dc link voltage. Moreover, the ZVS performance will be influenced by removing the clamping...

  5. Improved Control Strategy for T-type Isolated DC/DC Converters

    Liu, Dong; Deng, Fujin; Wang, Yanbo

    2017-01-01

    T-type isolated DC/DC converters have recently attracted attention due to their numerous advantages, including few components, low cost, and symmetrical operation of transformers. This study proposes an improved control strategy for increasing the efficiency of T-type isolated DC/DC converters....... Under the proposed strategy, the primary circulating current flows through the auxiliary switches (metal–oxide–semiconductor field-effect transistors) instead of their body diodes in free-wheeling periods. Such feature can reduce conduction losses, thereby improving the efficiency of T-type isolated DC...

  6. DC Voltage Droop Control Implementation in the AC/DC Power Flow Algorithm: Combinational Approach

    Akhter, F.; Macpherson, D.E.; Harrison, G.P.

    2015-01-01

    of operational flexibility, as more than one VSC station controls the DC link voltage of the MTDC system. This model enables the study of the effects of DC droop control on the power flows of the combined AC/DC system for steady state studies after VSC station outages or transient conditions without needing...... to use its complete dynamic model. Further, the proposed approach can be extended to include multiple AC and DC grids for combined AC/DC power flow analysis. The algorithm is implemented by modifying the MATPOWER based MATACDC program and the results shows that the algorithm works efficiently....

  7. Design of PI Controlled Non Isolated Bidirectional DC to DC Converter for Electric Vehicle Application

    Geetha, A.; Subramani, C.; Thamizh Thentral, T. M.; Krithika, V.; Usha, S.

    2018-04-01

    Non isolated Bidirectional DC-DC Converter (NIBDDC) is a good interface between DC source and inverter Fed induction motor drive. This paper deals with comparison between open loop and PI controlled Bidirectional DC to DC Converter Inverter System (BDDCIS). The modelling and control of BDDC is becomes an important issue. Open loop BDDCIS and closed loop PI controlled BDDCIS are designed, modelled and simulated using Matlab- simulink and their results are presented. The investigations indicate superior performance of PI controlled BDDCIS. The proposed BDDCIS has advantages like bidirectional power transfer ability, reduced hardware count and improved dynamic response.

  8. Drilling history core hole DC-4

    1978-12-01

    Core hole DC-4 was completed at a depth of 3998 feet in December, 1978 by Boyles Brothers Drilling Company, Spokane, Washington, under subcontract to Fenix and Scission, Inc. The hole was cored for the US Department of Energy and the Rockwell Hanford Operations' Basalt Waste Isolation Program. Fenix and Sicsson, Inc. furnished the engineering, daily supervision of the cable tool and core drilling activities, and geological core logging for DC-4. Core hole DC-4 is located on the Hanford Site about 3 miles east of the Yakima Barricade and approximately 103 feet southwest of rotary hole DC-5, which was completed to 3990 feet in February, 1978. Hanford Site coordinates reported for hole DC-4 are north 49,385.62 feet and west 85,207.63 feet, and Washington State coordinates are north 454,468.73 feet and east 2,209,990.87 feet. No elevation survey is available for hole DC-4, but it is approximately 745 feet above mean sea level based upon the survey of hole DC-5, which has a reported elevation of 745.16 feet on the top of the 3-inch flange. The purpose of core hole DC-4 was to core drill vertically through the basalt and interbed units for stratigraphic depth determination and core collection, and to provide a borehole for hydrologic testing, cross-hole seismic shear, and pressure wave velocity studies with rotary hole DC-5. Hole DC-4 was drilled through the overburden into basalt bedrock by cable tool methods (0-623 feet) and continuously cored through the final interval (623 to 3998 feet).Core recovery was 95.8 percent of the total footage cored

  9. Controlling DC-DC converters by chaos-based pulse width modulation to reduce EMI

    Li Hong; Zhang Bo; Li Zhong; Halang, Wolfgang A.; Chen Guanrong

    2009-01-01

    In this paper, periodic and chaotic behaviors of DC-DC converters under certain parametric conditions are simulated, experimentally verified, and analyzed. Motivated by the work of J.H.B. Deane and D.C. Hamill in 1996, where chaotic phenomena are useful in suppressing electromagnetic interference (EMI) by adjusting the parameters of the DC-DC converter and making it operate in chaos, a chaos-based pulse width modulation (CPWM) is proposed to distribute the harmonics of the DC-DC converters continuously and evenly over a wide frequency range, thereby reducing the EMI. The output waves and spectral properties of the EMI are simulated and analyzed as the carrier frequency or amplitude changes with regard to different chaotic maps. Simulation and experimental results are given to illustrate the effectiveness of the proposed CPWM, which provides a good example of applying chaos theory in engineering practice.

  10. A Dual-Buck–Boost AC/DC Converter for DC Nanogrid With Three Terminal Outputs

    Wu, Weimin; Wang, Houqing; Liu, Yuan

    2017-01-01

    Due to the widely used dc characterized loads and more distributed power generation sources, the dc nanogrid becomes more and more popular, and it is seen as an alternative to the ac grid. For safety considerations, the dc nanogrid should provide reliable grounding for the residential loads...... such as the low-voltage ac power system. There are three typical grounding configurations for a dc nanogrid: the united grounding, the unidirectional grounding, and the virtual isolated grounding. Each grounding configuration has its own specifications to ac/dc converters. In this paper, a dual-buck-boost ac/dc...... converter for use in the united-grounding-configuration-based dc nanogrid with three terminal outputs is proposed. The working principle of this converter is presented in detail through analyzing the equivalent circuits. Experiments are carried out to verify the theoretical analysis....

  11. A high voltage ratio and low ripple interleaved DC-DC converter for fuel cell applications.

    Chang, Long-Yi; Chao, Kuei-Hsiang; Chang, Tsang-Chih

    2012-01-01

    This paper proposes a high voltage ratio and low ripple interleaved boost DC-DC converter, which can be used to reduce the output voltage ripple. This converter transfers the low DC voltage of fuel cell to high DC voltage in DC link. The structure of the converter is parallel with two voltage-doubler boost converters by interleaving their output voltages to reduce the voltage ripple ratio. Besides, it can lower the current stress for the switches and inductors in the system. First, the PSIM software was used to establish a proton exchange membrane fuel cell and a converter circuit model. The simulated and measured results of the fuel cell output characteristic curve are made to verify the correctness of the established simulation model. In addition, some experimental results are made to validate the effectiveness in improving output voltage ripple of the proposed high voltage ratio interleaved boost DC-DC converters.

  12. Improved DC Gun Insulator Assembly

    Neubauer, M.L.; Dudas, A.; Sah, R.; Poelker, M.; Surles-Law, K.E.L.

    2010-01-01

    Many user facilities such as synchrotron radiation light sources and free electron lasers require accelerating structures that support electric fields of 10-100 MV/m, especially at the start of the accelerator chain where ceramic insulators are used for very high gradient DC guns. These insulators are difficult to manufacture, require long commissioning times, and often exhibit poor reliability. Two technical approaches to solving this problem will be investigated. Firstly, inverted ceramics offer solutions for reduced gradients between the electrodes and ground. An inverted design will be presented for 350 kV, with maximum gradients in the range of 5-10 MV/m. Secondly, novel ceramic manufacturing processes will be studied, in order to protect triple junction locations from emission, by applying a coating with a bulk resistivity. The processes for creating this coating will be optimized to provide protection as well as be used to coat a ceramic with an appropriate gradient in bulk resistivity from the vacuum side to the air side of an HV standoff ceramic cylinder. Example insulator designs are being computer modelled, and insulator samples are being manufactured and tested

  13. Investigations of dc breakdown fields

    Ramsvik, Trond; Reginelli, Alessandra; Taborelli, Mauro

    2006-01-01

    The need for high accelerating gradients for the future 30 GHz multi-TeV e+e- Compact Linear Collider (CLIC) at CERN has triggered a comprehensive study of DC breakdown fields of metals in UHV. The study shows that molybdenum (Mo), tungsten (W), titanium (Ti) and TiVAl reach high breakdown fields, and are thus good candidates for the iris material of CLIC structures. A significant decrease in the saturated breakdown field (Esat) is observed for molybdenum and tungsten when exposed to air. Specifically, at air pressures of 10-5 mbar, the decrease in Esat is found to be 50% and 30% for molybdenum and tungsten, respectively. In addition, a 30% decrease is found when molybdenum is conditioned with a CO pressure of ~1-10-5 mbar. Surface analysis measurements and breakdown conditioning in O2 ambience imply that the origin of the decrease in Esat is closely linked to oxide formation on the cathode surface. "Ex-situ" treatments by ion bombardment of molybdenum effectively reduce the oxide layers, and improve the brea...

  14. A THREE-PHASE BOOST DC-AC CONVERTER

    dc-ac converter (inverter) based on the dc-dc boost converters. ... Sliding mode controllers are designed to perform a robust control for the ... Computer simulations and spectral analysis demon- ... the conventional three-phase buck inverter,.

  15. 75 FR 75872 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-30, DC-9-40, and DC-9-50...

    2010-12-07

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 9-30, DC-9-40, and DC-9-50 Series Airplanes...: We are adopting a new airworthiness directive (AD) for the McDonnell Douglas Corporation airplanes... to include an airworthiness directive (AD) that would apply to certain McDonnell Douglas Model DC-9...

  16. Chemical constituents of Helichrysum italicum (Roth G. Don essential oil and their antimicrobial activity against Gram-positive and Gram-negative bacteria, filamentous fungi and Candida albicans

    Bouzid Djihane

    2017-07-01

    Full Text Available The aerial parts of Helichrysum italicum (Roth G. Don were subjected to hydrodistillation to obtain essential oils which had been analyzed by gas chromatography and gas chromatography coupled with mass spectrometry and tested for antimicrobial activity against 12 bacteria, two yeasts and four fungi by agar diffusion method. The essential oil yielded 0.44% (v/w and 67 compounds accounting for 99.24% of the oil were identified with a high content of oxygenated sesquiterpenes (61.42%. The most oxygenated sesquiterpene compounds were α-Cedrene (13.61%, α-Curcumene (11.41%, Geranyl acetate (10.05%, Limonene (6.07%, Nerol (5.04%, Neryl acetate (4.91% and α-Pinene (3.78%. The antimicrobial activity of the essential oil was assayed by using the disk diffusion method on Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 6538, Micrococcus luteus ATCC 4698, Klebsiella pneumonia ATCC 4352, Enterococcus cereus ATCC 2035, Bacillus cereus ATCC 10876, Staphylococcus epidermidis ATCC 12228, Bacillus subtilis ATCC 9372, Pseudomonas aeruginosa ATCC 27853, Enterococcus faecalis ATCC 49452, Proteus mirabilis ATCC 35659, Listeria monocytogenes ATCC 15313 and yeasts Candida albicans ATCC 10231, Saccharomyces cerevisiae ATCC 9763 and fungi, Fusarium solani var. coeruleum, Aspergillus niger, Alternaria alternata, Ascochyta rabiei. H. italicum inhibited the growth of all the tested microorganisms except three bacteria, E. coli ATCC 25922, K. pneumonia ATCC 4352 and L. monocytogenes ATCC 15313. The most sensitive bacterium was E. cereus ATCC 2035 with minimum inhibitory and bactericidal concentrations of 0.79 μg ml−1. A minimum fungistatic and fungicide concentration of 6.325 μg ml−1 and 12.65 μg ml−1 respectively was obtained with C. albicans ATCC 10231 and S. cerevisiae ATCC 9763. However the four fungi were more resistant with fungistatic minimum concentration ranging from 6.325 μg ml−1 to 50.6 μg ml−1 and a fungicide minimum

  17. Quantitative mapping of elemental distribution in leaves of the metallophytes Helichrysum candolleanum, Blepharis aspera, and Blepharis diversispina from Selkirk Cu–Ni mine, Botswana

    Koosaletse-Mswela, Pulane, E-mail: pulane.mswela@mopipi.ub.bw [Environmental Sciences Department, University of Botswana, Private Bag 00704, Gaborone (Botswana); Przybyłowicz, Wojciech J., E-mail: przybylowicz@tlabs.ac.za [iThemba Laboratory for Accelerator Based Sciences, National Research Foundation, PO Box 722, 7129 Somerset West (South Africa); AGH University of Science and Technology, Faculty of Physics & Applied Computer Science, Al. A. Mickiewicza 30, 30-059 Krakow (Poland); Cloete, Karen J., E-mail: kcloete@tlabs.ac.za [iThemba Laboratory for Accelerator Based Sciences, National Research Foundation, PO Box 722, 7129 Somerset West (South Africa); Barnabas, Alban D., E-mail: alban@tlabs.ac.za [iThemba Laboratory for Accelerator Based Sciences, National Research Foundation, PO Box 722, 7129 Somerset West (South Africa); Torto, Nelson, E-mail: ntorto@bitri.co.bw [Department of Chemistry, Rhodes University, PO Box 94, Grahamstown 6140 (South Africa); Mesjasz-Przybyłowicz, Jolanta, E-mail: mesjasz@tlabs.ac.za [iThemba Laboratory for Accelerator Based Sciences, National Research Foundation, PO Box 722, 7129 Somerset West (South Africa)

    2015-11-15

    Multi-element profiling is essential in understanding the metal-tolerant behavior of metallophytes. Although previous reports using multi-elemental analyses show that the metallophytes Blepharis aspera, Blepharis diversispina (Acanthaceae) and Helichrysum candolleanum (Asteraceae) take up metals, no information exists on elemental spatial distribution and concentrations in specific tissues of these plants. The aim of this study therefore was to assess the spatial distribution and concentration of copper, nickel and other elements in leaf tissues of these plants using micro-PIXE. Whole plants were collected with soil in pots from an operational copper and nickel mine (i.e., a copper and nickel mineralized area), Selkirk, about 40 km north-east of Francistown, Botswana. On the same day the samples were transported by air to iThemba LABS in South Africa. Leaf specimens were cryofixed in liquid propane cooled by LN2. Parallel samples were embedded in resin for anatomical studies to facilitate interpretation of elemental maps. The distribution and concentration of copper, nickel, and other elements in leaf tissues were determined using micro-PIXE and proton backscattering spectrometry. Data evaluation was performed using GeoPIXE II software. Micro-PIXE showed that H. candolleanum had the highest whole leaf content of copper (70 ± 3 μg g{sup −1} DW) and nickel (168 ± 5 μg g{sup −1} DW), followed by B. aspera (Cu: 25 ± 1 μg g{sup −1} DW; Ni: 166 ± 4 μg g{sup −1} DW) and B. diversispina (Cu: 3 ± 1 μg g{sup −1} DW; Ni, below detection limit). For specific leaf tissues, the highest levels of copper were found in the vascular bundle for H. candolleanum (167 ± 7 μg g{sup −1} DW) and the lower epidermis for B. aspera (70 ± 9 μg g{sup −1} DW). The highest levels of nickel were present in the vascular bundle of B. aspera (479 ± 10 μg g{sup −1} DW) and H. candolleanum (90 ± 5 μg g{sup −1} DW). Elemental maps showed a similar distribution pattern

  18. Quantitative mapping of elemental distribution in leaves of the metallophytes Helichrysum candolleanum, Blepharis aspera, and Blepharis diversispina from Selkirk Cu-Ni mine, Botswana

    Koosaletse-Mswela, Pulane; Przybyłowicz, Wojciech J.; Cloete, Karen J.; Barnabas, Alban D.; Torto, Nelson; Mesjasz-Przybyłowicz, Jolanta

    2015-11-01

    Multi-element profiling is essential in understanding the metal-tolerant behavior of metallophytes. Although previous reports using multi-elemental analyses show that the metallophytes Blepharis aspera, Blepharis diversispina (Acanthaceae) and Helichrysum candolleanum (Asteraceae) take up metals, no information exists on elemental spatial distribution and concentrations in specific tissues of these plants. The aim of this study therefore was to assess the spatial distribution and concentration of copper, nickel and other elements in leaf tissues of these plants using micro-PIXE. Whole plants were collected with soil in pots from an operational copper and nickel mine (i.e., a copper and nickel mineralized area), Selkirk, about 40 km north-east of Francistown, Botswana. On the same day the samples were transported by air to iThemba LABS in South Africa. Leaf specimens were cryofixed in liquid propane cooled by LN2. Parallel samples were embedded in resin for anatomical studies to facilitate interpretation of elemental maps. The distribution and concentration of copper, nickel, and other elements in leaf tissues were determined using micro-PIXE and proton backscattering spectrometry. Data evaluation was performed using GeoPIXE II software. Micro-PIXE showed that H. candolleanum had the highest whole leaf content of copper (70 ± 3 μg g-1 DW) and nickel (168 ± 5 μg g-1 DW), followed by B. aspera (Cu: 25 ± 1 μg g-1 DW; Ni: 166 ± 4 μg g-1 DW) and B. diversispina (Cu: 3 ± 1 μg g-1 DW; Ni, below detection limit). For specific leaf tissues, the highest levels of copper were found in the vascular bundle for H. candolleanum (167 ± 7 μg g-1 DW) and the lower epidermis for B. aspera (70 ± 9 μg g-1 DW). The highest levels of nickel were present in the vascular bundle of B. aspera (479 ± 10 μg g-1 DW) and H. candolleanum (90 ± 5 μg g-1 DW). Elemental maps showed a similar distribution pattern for copper and nickel in B. aspera and B diversispina, with these

  19. Chemical constituents of Helichrysum italicum (Roth) G. Don essential oil and their antimicrobial activity against Gram-positive and Gram-negative bacteria, filamentous fungi and Candida albicans.

    Djihane, Bouzid; Wafa, Nouioua; Elkhamssa, Soltani; Pedro, De Haro Juan; Maria, Angeles Esteban; Mohamed Mihoub, Zerroug

    2017-07-01

    The aerial parts of Helichrysum italicum (Roth) G. Don were subjected to hydrodistillation to obtain essential oils which had been analyzed by gas chromatography and gas chromatography coupled with mass spectrometry and tested for antimicrobial activity against 12 bacteria, two yeasts and four fungi by agar diffusion method. The essential oil yielded 0.44% (v/w) and 67 compounds accounting for 99.24% of the oil were identified with a high content of oxygenated sesquiterpenes (61.42%). The most oxygenated sesquiterpene compounds were α-Cedrene (13.61%), α-Curcumene (11.41%), Geranyl acetate (10.05%), Limonene (6.07%), Nerol (5.04%), Neryl acetate (4.91%) and α-Pinene (3.78%). The antimicrobial activity of the essential oil was assayed by using the disk diffusion method on Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 6538, Micrococcus luteus ATCC 4698, Klebsiella pneumonia ATCC 4352, Enterococcus cereus ATCC 2035, Bacillus cereus ATCC 10876, Staphylococcus epidermidis ATCC 12228, Bacillus subtilis ATCC 9372, Pseudomonas aeruginosa ATCC 27853, Enterococcus faecalis ATCC 49452, Proteus mirabilis ATCC 35659, Listeria monocytogenes ATCC 15313 and yeasts Candida albicans ATCC 10231, Saccharomyces cerevisiae ATCC 9763 and fungi, Fusarium solani var. coeruleum , Aspergillus niger , Alternaria alternata , Ascochyta rabiei . H. italicum inhibited the growth of all the tested microorganisms except three bacteria, E. coli ATCC 25922, K. pneumonia ATCC 4352 and L. monocytogenes ATCC 15313. The most sensitive bacterium was E. cereus ATCC 2035 with minimum inhibitory and bactericidal concentrations of 0.79 μg ml -1 . A minimum fungistatic and fungicide concentration of 6.325 μg ml -1 and 12.65 μg ml -1 respectively was obtained with C. albicans ATCC 10231 and S. cerevisiae ATCC 9763. However the four fungi were more resistant with fungistatic minimum concentration ranging from 6.325 μg ml -1 to 50.6 μg ml -1 and a fungicide minimum concentration of 50

  20. Quantitative mapping of elemental distribution in leaves of the metallophytes Helichrysum candolleanum, Blepharis aspera, and Blepharis diversispina from Selkirk Cu–Ni mine, Botswana

    Koosaletse-Mswela, Pulane; Przybyłowicz, Wojciech J.; Cloete, Karen J.; Barnabas, Alban D.; Torto, Nelson; Mesjasz-Przybyłowicz, Jolanta

    2015-01-01

    Multi-element profiling is essential in understanding the metal-tolerant behavior of metallophytes. Although previous reports using multi-elemental analyses show that the metallophytes Blepharis aspera, Blepharis diversispina (Acanthaceae) and Helichrysum candolleanum (Asteraceae) take up metals, no information exists on elemental spatial distribution and concentrations in specific tissues of these plants. The aim of this study therefore was to assess the spatial distribution and concentration of copper, nickel and other elements in leaf tissues of these plants using micro-PIXE. Whole plants were collected with soil in pots from an operational copper and nickel mine (i.e., a copper and nickel mineralized area), Selkirk, about 40 km north-east of Francistown, Botswana. On the same day the samples were transported by air to iThemba LABS in South Africa. Leaf specimens were cryofixed in liquid propane cooled by LN2. Parallel samples were embedded in resin for anatomical studies to facilitate interpretation of elemental maps. The distribution and concentration of copper, nickel, and other elements in leaf tissues were determined using micro-PIXE and proton backscattering spectrometry. Data evaluation was performed using GeoPIXE II software. Micro-PIXE showed that H. candolleanum had the highest whole leaf content of copper (70 ± 3 μg g"−"1 DW) and nickel (168 ± 5 μg g"−"1 DW), followed by B. aspera (Cu: 25 ± 1 μg g"−"1 DW; Ni: 166 ± 4 μg g"−"1 DW) and B. diversispina (Cu: 3 ± 1 μg g"−"1 DW; Ni, below detection limit). For specific leaf tissues, the highest levels of copper were found in the vascular bundle for H. candolleanum (167 ± 7 μg g"−"1 DW) and the lower epidermis for B. aspera (70 ± 9 μg g"−"1 DW). The highest levels of nickel were present in the vascular bundle of B. aspera (479 ± 10 μg g"−"1 DW) and H. candolleanum (90 ± 5 μg g"−"1 DW). Elemental maps showed a similar distribution pattern for copper and nickel in B. aspera

  1. Pulsed-DC selfsputtering of copper

    Wiatrowski, A; Posadowski, W M; Radzimski, Z J

    2008-01-01

    At standard magnetron sputtering conditions (argon pressure ∼0.5 Pa) inert gas particles are often entrapped in the formed films. Inert gas contamination can be eliminated by using the self-sustained magnetron sputtering process because it is done in the absence of the inert gas atmosphere. The self-sustained sputtering (SSS) gives also a unique condition during the transport of sputtered particles to the substrate. It is especially useful for filling high aspect ratio submicron scale structures for microelectronics. So far it has been shown that the self-sputtering process can be sustained in the DC operation mode (DC-SSS) only. The main disadvantage of DC-SSS process is instability related to possible arc formation. Usage of pulsed sputtering, similarly to reactive pulsed magnetron sputtering, could eliminate this problem. In this paper results of pulsed-DC self-sustained magnetron sputtering (pulsed DC-SSS) of copper are presented for the first time. The planar magnetron equipped with a 50 mm in diameter and 6 mm thick copper target was powered by DC-power supply modulated by power switch. The maximum target power was about 11 kW (∼550W/cm 2 ). The magnetron operation was investigated as a function of pulsing frequency (20-100 kHz) and duty factor (50-90%). The discharge extinction pressure was determined for these conditions. The plasma emission spectra (400-410nm range) and deposition rates were observed for both DC and pulsed DC sustained self-sputtering processes. The presented results illustrate that stable pulsed DC-SSS process can be obtained at pulsing frequency in the range of 60-100 kHz and duty factor of 70-90%

  2. Pulsed-DC selfsputtering of copper

    Wiatrowski, A.; Posadowski, W. M.; Radzimski, Z. J.

    2008-03-01

    At standard magnetron sputtering conditions (argon pressure ~0.5 Pa) inert gas particles are often entrapped in the formed films. Inert gas contamination can be eliminated by using the self-sustained magnetron sputtering process because it is done in the absence of the inert gas atmosphere. The self-sustained sputtering (SSS) gives also a unique condition during the transport of sputtered particles to the substrate. It is especially useful for filling high aspect ratio submicron scale structures for microelectronics. So far it has been shown that the self-sputtering process can be sustained in the DC operation mode (DC-SSS) only. The main disadvantage of DC-SSS process is instability related to possible arc formation. Usage of pulsed sputtering, similarly to reactive pulsed magnetron sputtering, could eliminate this problem. In this paper results of pulsed-DC self-sustained magnetron sputtering (pulsed DC-SSS) of copper are presented for the first time. The planar magnetron equipped with a 50 mm in diameter and 6 mm thick copper target was powered by DC-power supply modulated by power switch. The maximum target power was about 11 kW (~550W/cm2). The magnetron operation was investigated as a function of pulsing frequency (20-100 kHz) and duty factor (50-90%). The discharge extinction pressure was determined for these conditions. The plasma emission spectra (400-410nm range) and deposition rates were observed for both DC and pulsed DC sustained self-sputtering processes. The presented results illustrate that stable pulsed DC-SSS process can be obtained at pulsing frequency in the range of 60-100 kHz and duty factor of 70-90%.

  3. Superconducting DC homopolar motors for ship propulsion

    Heiberger, M.; Reed, M.R.; Creedon, W.P.; O' Hea, B.J. [General Atomic (United States)

    2000-07-01

    Superconducting DC homopolar motors have undergone recent advances in technology, warranting serious consideration of their use for ship propulsion. Homopolar motor propulsion is now practical because of two key technology developments: cryogen-free superconducting refrigeration and high performance motor fiber brushes. These compact motors are ideal for podded applications, where reduced drag and fuel consumption are predicted. In addition, the simple DC motor controller is more efficient and reliable compared with AC motor controllers. Military ships also benefit from increased stealth implicit in homopolar DC excitation, which also allows the option for direct hull or pod mounting. (authors)

  4. DC-Compensated Current Transformer †

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-01

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component. PMID:26805830

  5. High power density dc/dc converter: Selection of converter topology

    Divan, Deepakraj M.

    1990-01-01

    The work involved in the identification and selection of a suitable converter topology is described. Three new dc/dc converter topologies are proposed: Phase-Shifted Single Active Bridge DC/DC Converter; Single Phase Dual Active Bridges DC/DC Converter; and Three Phase Dual Active Bridges DC/DC Converter (Topology C). The salient features of these topologies are: (1) All are minimal in structure, i.e., each consists of an input and output bridge, input and output filter and a transformer, all components essential for a high power dc/dc conversion process; (2) All devices of both the bridges can operate under near zero-voltage conditions, making possible a reduction of device switching losses and hence, an increase in switching frequency; (3) All circuits operate at a constant frequency, thus simplifying the task of the magnetic and filter elements; (4) Since, the leakage inductance of the transformer is used as the main current transfer element, problems associated with the diode reverse recovery are eliminated. Also, this mode of operation allows easy paralleling of multiple modules for extending the power capacity of the system; (5) All circuits are least sensitive to parasitic impedances, infact the parasitics are efficently utilized; and (6) The soft switching transitions, result in low electromagnetic interference. A detailed analysis of each topology was carried out. Based on the analysis, the various device and component ratings for each topology operating at an optimum point, and under the given specifications, are tabulated and discussed.

  6. CISH is induced during DC development and regulates DC-mediated CTL activation.

    Miah, Mohammad Alam; Yoon, Cheol-Hee; Kim, Joonoh; Jang, Jinah; Seong, Young-Rim; Bae, Yong-Soo

    2012-01-01

    The cytokine inducible SH2-domain protein (CISH) is a well-known STAT5 target gene, but its role in the immune system remains uncertain. In this study, we found that CISH is predominantly induced during dendritic cell (DC) development from mouse bone marrow (BM) cells and plays a crucial role in type 1 DC development and DC-mediated CTL activation. CISH knockdown reduced the expression of MHC class I, co-stimulatory molecules and pro-inflammatory cytokines in BMDCs. Meanwhile, the DC yield was markedly enhanced by CISH knockdown via cell-cycle activation and reduction of cell apoptosis. Down-regulation of cell proliferation at the later stage of DC development was found to be associated with CISH-mediated negative feedback regulation of STAT5 activation. In T-cell immunity, OT-1 T-cell proliferation was significantly reduced by CISH knockdown in DCs, whereas OT-2 T-cell proliferation was not affected by CISH knockdown. CTLs generated by DC vaccination were also markedly reduced by CISH knockdown, followed by significant impairment of DC-based tumor immunotherapy. Taken together, our data suggest that CISH expression at the later stage of DC development triggers the shutdown of DC progenitor cell proliferation and facilitates DC differentiation into a potent stimulator of CTLs. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Study on the Control Algorithm of Two-Stage DC-DC Converter for Electric Vehicles

    Changhao Piao

    2014-01-01

    Full Text Available The fast response, high efficiency, and good reliability are very important characteristics to electric vehicles (EVs dc/dc converters. Two-stage dc-dc converter is a kind of dc-dc topologies that can offer those characteristics to EVs. Presently, nonlinear control is an active area of research in the field of the control algorithm of dc-dc converters. However, very few papers research on two-stage converter for EVs. In this paper, a fixed switching frequency sliding mode (FSFSM controller and double-integral sliding mode (DISM controller for two-stage dc-dc converter are proposed. And a conventional linear control (lag is chosen as the comparison. The performances of the proposed FSFSM controller are compared with those obtained by the lag controller. In consequence, the satisfactory simulation and experiment results show that the FSFSM controller is capable of offering good large-signal operations with fast dynamical responses to the converter. At last, some other simulation results are presented to prove that the DISM controller is a promising method for the converter to eliminate the steady-state error.

  8. Studi Komparasi Fungsi Keanggotaan Fuzzy sebagai Kontroler Bidirectional DC-DC Converter pada Sistem Penyimpan Energi

    Eka Prasetyono

    2015-09-01

    Full Text Available Bidirectional DC-DC converter is needed in the energy storage system. The converter topology used in this paper was a non-isolated bidirectional DC-DC buck-boost converter. This converter worked in two ways, which the charging mode stored energy into battery when load current was less than nominal main DC current (set point and discharging mode transferred energy from battery to the load when its current exceeded set point value. Both of these modes worked automatically according to the load current. The charging and discharging currents were controlled by fuzzy logic controller which was implemented on microcontroller ARM Cortex-M4F STM32F407VG. This paper compares two types of fuzzy membership function (triangular and sigmoid in controlling bidirectional DC-DC converter. The results showed that fuzzy logic controller with triangle membership function and sigmoid as control bidirectional DC-DC converter had no significant different response, both had an average error for charging and discharging process under 4% with ripple current on the main DC bus around 0.5%. The computing time of program for fuzzy logic controller with triangular membership functions had 19.01% faster than sigmoid, and fuzzy logic computation time on a microcontroller with hardware floating point was 60% faster than software floating point.

  9. NAMMA DC-8 DROPSONDE V1

    National Aeronautics and Space Administration — The DC-8 dropsonde system uses an integrated, highly accurate, GPS-located atmospheric profiling dropsonde, which measures and records current atmospheric conditions...

  10. dc power system for deuteron accelerator

    Creek, K.O.; Liska, D.J.

    1981-01-01

    The Fusion Materials Irradiation Test (FMIT) Facility dc power system provides excitation current for all linac and High-Energy Beam Transport (HEBT) quadrupole and bending magnets, excitation for horizontal and vertical beam steering, and current-bypass shunts.

  11. Determination of input/output characteristics of full-bridge AC/DC/DC converter for arc welding

    Stefanov, Goce; Karadzinov, Ljupco; Sarac, Vasilija; Cingoski, Vlatko; Gelev, Saso

    2016-01-01

    This paper describes the design and practical implementation of AC/DC/DC converter in mode of arc welding. An analysis of the operation of AC/DC/DC converter and its input/output characteristics are determined with computer simulations. The practical part is consisted of AC/DC/DC converter prototype for arc welding with output power of 3 kW and switching frequency of 64 kHz. The operation of AC/DC/DC converter is validated with experimental measurements.

  12. Ultra-high Efficiency DC-DC Converter using GaN Devices

    Ramachandran, Rakesh

    2016-01-01

    properties of GaN devices can be utilized in power converters to make them more compact and highly efficient. This thesis entitled “Ultra-high Efficiency DC-DC Converter using GaN devices” focuses on achieving ultra-high conversion efficiency in an isolated dc-dc converter by the optimal utilization of Ga...... for many decades. However, the rate of improvement slowed as the silicon power materials asymptotically approached its theoretical bounds. Compared to Si, wideband gap materials such as Silicon Carbide (SiC) and Gallium Nitride (GaN) are promising semiconductors for power devices due to their superior...... in this thesis. Efficiency measurements from the hardware prototype of both the topologies are also presented in this thesis. Finally, the bidirectional operation of an optimized isolated dc-dc converter is presented. The optimized converter has achieved an ultra-high efficiency of 98.8% in both directions...

  13. Modeling, Analysis and Control of Different DC-DC Converter Topologies for Photo Voltaic Emulator

    Mohammad Tauquir Iqbal

    2016-05-01

    Full Text Available This paper presents the modeling, analysis and control of different DC-DC converter topologies to emulate the photovoltaic (PV system. A PV emulator is basically a DC-DC converter having same electrical characteristics that of solar PV panel.  The emulator helps to achieve real characteristics of PV system in a better way in an environment where using actual PV systems can produce inconsistent results due to variation in weather conditions. The paper describes different types of DC-DC converters like buck, Resonant and Quasi Resonant Converter. The complete system is modelled in MATLAB® Simulink SimPowerSystem software package. The Simulation results obtained from the MATLAB® Simulink SimPowerSystem software package for different topologies under steady and dynamic conditions are analyzed and presented. An evaluation table is also presented at the end of the paper, presenting the effectiveness of each topology.

  14. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-01-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  15. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-04-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  16. Test Results of Selected Commercial DC/DC Converters under Cryogenic Temperatures - A Digest

    Patterson, Richard; Hammoud, Ahmad

    2010-01-01

    DC/DC converters are widely used in space power systems in the areas of power management and distribution, signal conditioning, and motor control. Design of DC/DC converters to survive cryogenic temperatures will improve the power system performance, simplify design, and reduce development and launch costs. In this work, the performance of nine COTS modular, low-tomedium power DC/DC converters was investigated under cryogenic temperatures. The converters were evaluated in terms of their output regulation, efficiency, and input and output currents. At a given temperature, these properties were obtained at various input voltages and at different load levels. A summary on the performance of the tested converters was given. More comprehensive testing and in-depth analysis of performance under long-term exposure to extreme temperatures are deemed necessary to establish the suitability of these and other devices for use in the harsh environment of space exploration missions.

  17. Precharge strategies for isolated modular DC-DC converters under two different start-up conditions

    Zhang, Yi; Wang, Huai; Li, Binbin

    2017-01-01

    The isolated modular DC-DC converter (IMDCC) is a new topology designed to connect high-voltage direct current (HVDC) lines with different voltage levels, which ties two DC grids by using two modular multilevel converters (MMCs) via a medium-frequency transformer. Due to the large value of capaci......The isolated modular DC-DC converter (IMDCC) is a new topology designed to connect high-voltage direct current (HVDC) lines with different voltage levels, which ties two DC grids by using two modular multilevel converters (MMCs) via a medium-frequency transformer. Due to the large value...... of capacitance in the IMDCC, proper precharge strategies before the start-up are significant for the safety and reliability of the whole system. This paper presents two closed-loop precharge control strategies to fully charge the sub-module (SM) capacitors of the IMDCC, considering two different start...

  18. Kingsnorth-London dc transmission link

    1966-03-11

    The hvdc transmission link between one of the 500 MW generators at Kingsnorth Power Station and two receiving stations in London will use a three-wire dc cable system rated to carry 1200 A at +- 266 kV. This 51-mile system will be the first dc link in the world to be used as an integral part of a complex interconnected ac network.

  19. Hole history, rotary hole DC-3

    1977-10-01

    Purpose of hole DC-3 was to drill into the Umtanum basalt flow using both conventional rotary and core drilling methods. The borehole is to be utilized for geophysical logging, future hydrological testing, and the future installation of a borehole laboratory for long-term pressure, seismic, and moisture migration or accumulation recording in the Umtanum basalt flow in support of the Basalt Waste Isolation Program. Hole DC-3 is located east of the 200 West barricaded area on the Hanford reservation

  20. DC-8 MTP calibration for SOLVE-2

    Mahoney, M. J.

    2003-01-01

    The Jet Propulsion Laboratory (JPL) Microwave Temperature Profiler (MTP) was the only instrument making temperature measurements at and below flight level on the DC-8 during the SOLVE-2 campaign. Many years of careful comparison of MTP measurements with radiosondes near the DC-8 flight track have shown that the flight level temperature can be determined to an accuracy of 0.2K relative to radiosondes.

  1. dc illusion and its experimental verification

    Liu, Min; Lei Mei, Zhong; Ma, Xiang; Cui, Tie Jun

    2012-07-01

    Based on the transformation optics method, we propose a dc illusion device, which can transform a metallic object into a magnified dielectric object using anisotropic conducting materials. Utilizing the analogy between electric conductivities and resistor networks, we design and fabricate the device using metal film resistors. The practical measurement data agree very well with simulation results. The proposed dc illusion device is easy to process and measure, and thus has potential applications in various sectors.

  2. Characterization of diode valve in medium voltage dc/dc converter for wind turbines

    Dincan, Catalin Gabriel; Kjær, Philip Carne

    2016-01-01

    This paper proposes a methodology for characterization of medium voltage (MV), medium frequency (MF) rectifier diode valve. The intended application is for 10MW dc/dc converters used in DC offshore wind turbines. Sensitivity to semiconductor component parameter variation, snubber component tolera...... tolerance, influence of temperature and stray capacitance are analyzed. It is concluded that the largest impact on sensitivity is given by reverse recovery charge variation and differences of temperature between adjacent devices....

  3. Computer Simulation of Phase Shifted Series Resonant DC to DC Converter

    P. PARVATHY

    2016-01-01

    Full Text Available This paper deals with digital simulation of phase shifted series resonant DC to DC converter using Matlab Simulink. The Simulink models for open loop and closed loop systems are developed and they are used for simulation studies. This converter is capable of producing ripple free DC output. Switching losses and switching stresses are reduced by using soft switching. This converter has advantages like high power density and low switching losses. Theoretical predictions are well supported by the simulation results.

  4. DC-Link Compensation Method for Slim DC Link Drives Fed by Soft Grid

    Mathe, Laszlo; Rosendahl Andersen, Henrik; Lazar, Radu

    2010-01-01

    Slim DC-link PWM (AC) drives for lowperformance applications are emerging on the market. Such drives equipped with a small DC-link capacitance exhibit instability tendencies, if installed on a soft line, giving a degraded performance. The total harmonic distortion (THD) and the partially weighted...... harmonic distortion (PWHD) of the line current are degraded, if resonance between the line impedance and the DC-link capacitance occurs. Likewise, the motor performance is affected negatively giving extra torque ripple, vibration and acoustic-noise emission. This paper proposes a novel DC-link compensation...

  5. Egr2 induced during DC development acts as an intrinsic negative regulator of DC immunogenicity.

    Miah, Mohammad Alam; Byeon, Se Eun; Ahmed, Md Selim; Yoon, Cheol-Hee; Ha, Sang-Jun; Bae, Yong-Soo

    2013-09-01

    Early growth response gene 2 (Egr2), which encodes a zinc finger transcription factor, is rapidly and transiently induced in various cell types independently of de novo protein synthesis. Although a role for Egr2 is well established in T-cell development, Egr2 expression and its biological function in dendritic cells (DCs) have not yet been described. Here, we demonstrate Egr2 expression during DC development, and its role in DC-mediated immune responses. Egr2 is expressed in the later stage of DC development from BM precursor cells. Even at steady state, Egr2 is highly expressed in mouse splenic DCs. Egr2-knockdown (Egr2-KD) DCs showed increased levels of major histocompatability complex (MHC) class I and II and co-stimulatory molecules, and enhanced antigen uptake and migratory capacities. Furthermore, Egr2-KD abolished SOCS1 expression and signal transducer and activator of transcription 5 (STAT5) activation during DC development, probably resulting in the enhancement of IL-12 expression and Th1 immunogenicity of a DC vaccine. DC-mediated cytotoxic T lymphocyte (CTL) activation and antitumor immunity were significantly enhanced by Egr2-KD, and impaired by Egr2 overexpression in antigen-pulsed DC vaccines. These data suggest that Egr2 acts as an intrinsic negative regulator of DC immunogenicity and can be an attractive molecular target for DC vaccine development. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Analysis of high voltage step-up nonisolated DC-DC boost converters

    Alisson Alencar Freitas, Antônio; Lessa Tofoli, Fernando; Junior, Edilson Mineiro Sá; Daher, Sergio; Antunes, Fernando Luiz Marcelo

    2016-05-01

    A high voltage step-up nonisolated DC-DC converter based on coupled inductors suitable to photovoltaic (PV) systems applications is proposed in this paper. Considering that numerous approaches exist to extend the voltage conversion ratio of DC-DC converters that do not use transformers, a detailed comparison is also presented among the proposed converter and other popular topologies such as the conventional boost converter and the quadratic boost converter. The qualitative analysis of the coupled-inductor-based topology is developed so that a design procedure can be obtained, from which an experimental prototype is implemented to validate the theoretical assumptions.

  7. High-Voltage DC-DC Converter Topology for PV Energy Utilization - Investigation and Implementation

    Sanjeevikumar, Padmanaban; Blaabjerg, Frede; Wheeler, Patrick

    2017-01-01

    This paper exploited the utilization of photovoltaic (PV) energy system with high-voltage (HV) output DC-DC converter. Classical boost converters are used for both renewable energy integration and HV applications, but limited by reducing output/efficiency in performance. Moreover, as parasitic...... elements suppress the power transfer ratio, converter needs to maximize the PV energy utilization. This investigation study focused to include additional parasitic elements (voltage-lift technique) to a standard DC-DC buck converter and to overcome all the above drawbacks to maximize the PV power...

  8. Digital peak current mode control with adaptive slope compensation for DC-DC converters

    Andersen, Karsten Holm; Nymand, Morten

    2017-01-01

    performance and stability of current mode control. The presented method adapt to DC-DC converter operating conditions by estimating the rising and falling inductor current slopes, to apply a current slope compensation value to obtain a constant quality factor. The experimental results verifies the theoretical......This paper presents an adaptive slope compensation method for peak current mode control of digital controlled DC-DC converters, which controls the quality factor of the complex conjugated poles at half the switching frequency. Using quality factor control enables optimization of the dynamic...

  9. A Novel PPFHB Bidirectional DC-DC Converter for Supercapacitor Application

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

    2009-01-01

    This paper presents a novel bidirectional DC-DC converter for the supercapacitor application. In the proposed converter, push-pull forward with half bridge (PPFHB) voltage doubler structure is used to reduce the number of the power switches and get higher voltage gain. Based on phase-shift modula......This paper presents a novel bidirectional DC-DC converter for the supercapacitor application. In the proposed converter, push-pull forward with half bridge (PPFHB) voltage doubler structure is used to reduce the number of the power switches and get higher voltage gain. Based on phase...

  10. The application of standardized control and interface circuits to three dc to dc power converters.

    Yu, Y.; Biess, J. J.; Schoenfeld, A. D.; Lalli, V. R.

    1973-01-01

    Standardized control and interface circuits were applied to the three most commonly used dc to dc converters: the buck-boost converter, the series-switching buck regulator, and the pulse-modulated parallel inverter. The two-loop ASDTIC regulation control concept was implemented by using a common analog control signal processor and a novel digital control signal processor. This resulted in control circuit standardization and superior static and dynamic performance of the three dc-to-dc converters. Power components stress control, through active peak current limiting and recovery of switching losses, was applied to enhance reliability and converter efficiency.

  11. Laboratory manual for pulse-width modulated DC-DC power converters

    Kazimierczuk, Marian K

    2015-01-01

    Designed to complement a range of power electronics study resources, this unique lab manual helps students to gain a deep understanding of the operation, modeling, analysis, design, and performance of pulse-width modulated (PWM) DC-DC power converters.  Exercises focus on three essential areas of power electronics: open-loop power stages; small-signal modeling, design of feedback loops and PWM DC-DC converter control schemes; and semiconductor devices such as silicon, silicon carbide and gallium nitride. Meeting the standards required by industrial employers, the lab manual combines program

  12. A Bidirectional Multi-Port DC-DC Converter Integrating Voltage Equalizer

    Chen, Jianfei; Hou, Shiying; Deng, Fujin

    2015-01-01

    A novel bidirectional multi-port dc-dc converter integrating voltage equalizer based on switched-capacitor voltage accumulator (SCVA) is proposed. It has two operating modes of charging and discharging for battery modules. All battery modules are connected in series indirectly and can be equalize...... battery modules with different voltages. Simulation results has shown the feasibility of the proposed converter.......A novel bidirectional multi-port dc-dc converter integrating voltage equalizer based on switched-capacitor voltage accumulator (SCVA) is proposed. It has two operating modes of charging and discharging for battery modules. All battery modules are connected in series indirectly and can be equalized...

  13. A Bidirectional Resonant DC-DC Converter Suitable for Wide Voltage Gain Range

    Shen, Yanfeng; Wang, Huai; Al-Durra, Ahmed

    2018-01-01

    This paper proposes a new bidirectional resonant dc-dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc-dc converters, and meanwhile achieves high efficiency...... losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology...... and analysis are verified with experimental results obtained from a 1-kW converter prototype....

  14. Design of the DC-DC power stage of the capacitor charger for MAXIDISCAP power converters

    Cravero, Jean-Marc

    2013-01-01

    This technical report presents the design of the DC-DC power stage of the capacitor charger for MAXIDISCAP power converters. The power stage is based on a half bridge series resonant converter in Discontinuous Conduction Mode (DCM). This simple and robust topology allows obtaining a current source behavior with a low switching losses power stage. The associated control stage is implemented using a commercial controller which has differenti nternal circuits that allows a high integration of the converter control system. The report presents the design and tuning criteria for the DC-DC converter, including the power stage and the control system.

  15. Analysis and Design of Bi-Directional DC-DC Converter in the Extended Run Time DC UPS System Based on Fuel Cell and Supercapacitor

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2009-01-01

    Abstract-In this paper, an extended run time DC UPS system structure with fuel cell and supercapacitor is investigated. A wide input range bi-directional dc-dc converter is described along with the phase-shift modulation scheme and phase-shift with duty cycle control, in different modes. The deli......Abstract-In this paper, an extended run time DC UPS system structure with fuel cell and supercapacitor is investigated. A wide input range bi-directional dc-dc converter is described along with the phase-shift modulation scheme and phase-shift with duty cycle control, in different modes...

  16. Impact of Faults and Protection Methods on DC Microgrids Operation

    Bayati, Navid; Hajizadeh, Amin; N. Soltani, Mohsen

    2018-01-01

    with the DC Microgrid. This paper evaluates and presents a comprehensive review on the most recent studies in the DC Microgrids protection. Moreover, the fault behavior and characteristics of DC Microgrids, the effect of Constant Power Load (CPL) , and recent DC Microgrid protection methods are reviewed. Also...

  17. Zero-voltage DC/DC converter with asymmetric pulse-width modulation for DC micro-grid system

    Lin, Bor-Ren

    2018-04-01

    This paper presents a zero-voltage switching DC/DC converter for DC micro-grid system applications. The proposed circuit includes three half-bridge circuit cells connected in primary-series and secondary-parallel in order to lessen the voltage rating of power switches and current rating of rectifier diodes. Thus, low voltage stress of power MOSFETs can be adopted for high-voltage input applications with high switching frequency operation. In order to achieve low switching losses and high circuit efficiency, asymmetric pulse-width modulation is used to turn on power switches at zero voltage. Flying capacitors are used between each circuit cell to automatically balance input split voltages. Therefore, the voltage stress of each power switch is limited at Vin/3. Finally, a prototype is constructed and experiments are provided to demonstrate the circuit performance.

  18. Ultrahigh-density trench cpacitors in silicon and their application to integrated DC-DC conversion

    Roozeboom, F.; Bergveld, H.J.; Nowak, K.; Le Cornec, F.; Guiraud, L.; Bunel, C.; Iochem, S.; Ferreira, J.; Ledain, S.; Pieraerts, E.; Pommier, M.

    2009-01-01

    This paper addresses silicon-based integration of passive components applied to 3D integration with dies of other technologies within one package. Particularly, the development of high-density trench capacitors has enabled the realization of small-formfactor DC-DC converters. As illustration, an

  19. Reliability study of high gain DC-DC converters based on RRPP I-IIA ...

    J DIVYA NAVAMANI

    2018-05-10

    May 10, 2018 ... Energy Storage Modules (ESM), Propulsion Motor Mod- ules (PMM) and ... All Electric Ship (AES) is the best way to power all the loads in the ship ... also used to derive quadratic step down DC-DC converters. [6]. The attractive ...... Exhibition on Ecological Vehicles and Renewable Energies,. TamilNadu ...

  20. Investigation of DC-DC Boost Converter for Reliability of Operational Planning

    Khazraj, Hesam; Ashouri, Mani; Silva, Filipe Miguel Faria da

    2018-01-01

    of the interests related to reliability is the power semiconductor switches, which are the most vulnerable elements. The failure of one-power switches can reduce the system reliability. Interleaved technique for DC-DC converters is a redundant strategy to improve the reliability, but at the cost of increasing...

  1. A New Sliding Mode Controller for DC/DC Converters in Photovoltaic Systems

    M. Sarvi

    2013-01-01

    Full Text Available DC/DC converters are widely used in many industrial and electrical systems. As DC/DC converters are nonlinear and time-variant systems, the application of linear control techniques for the control of these converters is not suitable. In this paper, a new sliding mode controller is proposed as the indirect control method and compared to a simple direct control method in order to control a buck converter in photovoltaic applications. The solar arrays are dependent power sources with nonlinear voltage-current characteristics under different environmental conditions (insolation and temperature. From this point of view, the DC/DC converter is particularly suitable for the application of the sliding mode control in photovoltaic application, because of its controllable states. Simulations are performed in Matlab/Simulink software. The simulation results are presented for a step change in reference voltage and input voltage as well as step load variations. The simulations results of proposed method are compared with the conventional PID controller. The results show the good performance of the proposed sliding mode controller. The proposed method can be used for the other DC/DC converter.

  2. Switched capacitor DC-DC converter with switch conductance modulation and Pesudo-fixed frequency control

    Larsen, Dennis Øland; Vinter, Martin; Jørgensen, Ivan Harald Holger

    A switched capacitor dc-dc converter with frequency-planned control is presented. By splitting the output stage switches in eight segments the output voltage can be regulated with a combination of switching frequency and switch conductance. This allows for switching at predetermined frequencies, 31...

  3. Spectral shaping of a randomized PWM DC-DC converter using maximum entropy probability distributions

    Dove, Albert

    2017-01-01

    Full Text Available maintaining constraints in a DC-DC converter is investigated. A probability distribution whose aim is to ensure maximal harmonic spreading and yet mainaint constraints is presented. The PDFs are determined from a direct application of the method of Maximum...

  4. Common mode noise in three-level DC-DC converters

    Grobler, Inus

    2009-09-01

    Full Text Available that three-level buck DC-DC converters in general generate much lower common mode currents than conventional two-level buck converters. Further, reductions in common mode currents are achieved by using the improved three-level topologies that have been...

  5. Y-Source Boost DC/DC Converter for Distributed Generation

    Siwakoti, Yam P.; Loh, Poh Chiang; Blaabjerg, Frede

    2015-01-01

    This paper introduces a versatile Y-source boost dc/dc converter intended for distributed power generation, where high gain is often demanded. The proposed converter uses a Y-source impedance network realized with a tightly coupled three-winding inductor for high voltage boosting that is presently...

  6. Experimental study of dynamic behaviors and routes to chaos in DC-DC boost converters

    Cafagna, D.; Grassi, G.

    2005-01-01

    This paper illustrates an experimental study of a current-programmed DC-DC boost converter, with the aim of investigating possible pathways through which the converter may enter chaos. In particular, based on experimental measurements, it is shown that variations of input voltage and reference current can generate periodic, subharmonic, quasi-periodic and chaotic behaviors

  7. Magnetically integrated high step-up resonant DC-DC converter for distributed photovoltaic systems

    Vinnikov, Dmitri; Chub, Andrii; Liivik, Elizaveta

    2017-01-01

    In this paper magnetically integrated resonant single-switch quasi-Z-source DC-DC converter is evaluated as a candidate topology for the low-cost photovoltaic microconverter. The derivation of the topology and its basic operation principle are explained. Generalized design guidelines...

  8. Quasiperiodicity and Torus Breakdown in a Power Electronic DC/DC Converter

    Zhusubaliyev, Zhanybai; Soukhoterin, Evgeniy; Mosekilde, Erik

    2007-01-01

    This paper discusses the mechanisms of torus formation and torus destruction in a dc/dc converter with relay control and hysteresis. We establish a chart of the dynamical modes in the input voltage versus load resistance parameter plane. This chart displays several different torus bifurcations...

  9. A DC-DC Converter with Wide Input Voltage Range for Fuel Cell and Supercapacitor Application

    Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael Andreas E.

    2009-01-01

    This paper proposes a novel phase-shift plus duty cycle controlled hybrid bi-directional DC-DC converter based on fuel cells and supercapacitors. The described converter employs two high frequency transformers to couple the half-bridge and full-bridge circuits together in the primary side...

  10. Modelling, Simulation and Construction of a DC/DC Boost Power Converter: A School Experimental System

    Silva-Ortigoza, R.; Silva-Ortigoza, G.; Hernandez-Guzman, V. M.; Saldana-Gonzalez, G.; Marcelino-Aranda, M.; Marciano-Melchor, M.

    2012-01-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders…

  11. High-power three-port three-phase bidirectional DC-DC converter

    Tao, H.; Duarte, J.L.; Hendrix, M.A.M.

    2007-01-01

    This paper proposes a three-port three-phase bidirectional dc-dc converter suitable for high-power applications. The converter combines a slow primary source and a fast storage to power a common load (e.g., an inverter). Since this type of system is gaining popularity in sustainable energy

  12. Floating high step-down stacked dc-dc converter based on buck-boost cells

    Tibola, G.; Duarte, J.L.; Blinov, A.

    2015-01-01

    In some high power dc-dc applications, where high voltage is present, a converter with high step-down ratio is required in order to provide an isolated low power auxiliary supply. This requirement represents a challenge and many topologies are currently being researched. The analysis of a

  13. Magnetically coupled high-gain Y-source isolated DC/DC converter

    Siwakoti, Yam P.; Loh, Poh Chiang; Blaabjerg, Frede

    2014-01-01

    A new form of magnetically coupled DC/DC converter is proposed for medium power applications (250 W to 2 kW), requiring a high-voltage gain, short inductive charging time and galvanic isolation. The proposed converter can be realised using a unique Y-source impedance network and a two-switch push...

  14. Modelling, simulation and construction of a dc/dc boost power converter: a school experimental system

    Silva-Ortigoza, R; Marciano-Melchor, M; Silva-Ortigoza, G; Hernández-Guzmán, V M; Saldaña-González, G; Marcelino-Aranda, M

    2012-01-01

    We introduce a dc/dc boost power converter as a didactic prototype intended to support courses on electric circuit analysis experimentally. The corresponding mathematical model is obtained, the converter is designed and an experimental setup is described, constructed and tested. Simplicity of construction as well as low cost of components renders the feasible introduction of this equipment in undergraduate laboratories. (paper)

  15. Comparative evaluation of bidirectional dual active bridge DC-DC converter variants

    Sfakianakis, G.; Everts, J.; Huisman, H.; Lomonova, E.A.

    2016-01-01

    For the realization of DC-DC converters in automotive industry, the Dual Active Bridge (DAB) converter seems to be a promising choice because of its soft-switching and high-power-density capability. Contrary to the traditional 3 level - 3 level (3-3L) DAB, a 3 level - 5 level (3-5L) DAB can operate

  16. A Novel Single Switch Transformerless Quadratic DC/DC Buck-Boost Converter

    Mostaan, Ali; A. Gorji, Saman; N. Soltani, Mohsen

    2017-01-01

    A novel quadratic buck-boost DC/DC converter is presented in this study. The proposed converter utilizes only one active switch and can step-up/down the input voltage, while the existing single switch quadratic buck/boost converters can only work in step-up or step-down mode. First, the proposed ...

  17. Single Event Burnout in DC-DC Converters for the LHC Experiments

    Claudio H. Rivetta et al.

    2001-09-24

    High voltage transistors in DC-DC converters are prone to catastrophic Single Event Burnout in the LHC radiation environment. This paper presents a systematic methodology to analyze single event effects sensitivity in converters and proposes solutions based on de-rating input voltage and output current or voltage.

  18. Design and Implementation of Digital Current Mode Controller for DC-DC Converters

    Taeed, Fazel

    to be regulated by a closed-loop controller. The Peak Current Mode Control (PCMC) is one of the most promising control methods for dc-dc converters. It has been known for high bandwidth (speed), and inherent current protection. Increasing the controller bandwidth decreases the output filter size and cost. Analog...

  19. Selection of DC/DC converter for offshore wind farms with MVDC power collection

    Dincan, Catalin Gabriel; Kjær, Philip Carne; Chen, Yu-Hsing

    2017-01-01

    Four DC/DC converters are analyzed and compared with respects to availability, efficiency, ratings, repair costs and power density. Intended application is offshore wind farms with MVDC power collection. The selected topology is a new series resonant converter, which offers 99% efficiency across...

  20. Area-Efficiency Trade-Offs in Integrated Switched-Capacitor DC-DC Converters

    Spliid, Frederik Monrad; Larsen, Dennis Øland; Knott, Arnold

    2016-01-01

    This paper analyzes the relationship between efficiency and chip area in a fully integrated switched capacitor voltage divider dc-dc converter implemented in 180nm-technology and a 1/2 topology. A numerical algorithm for choosing the optimal sizes of individual components, in terms of power loss...

  1. Research on Two-channel Interleaved Two-stage Paralleled Buck DC-DC Converter for Plasma Cutting Power Supply

    Yang, Xi-jun; Qu, Hao; Yao, Chen

    2014-01-01

    As for high power plasma power supply, due to high efficiency and flexibility, multi-channel interleaved multi-stage paralleled Buck DC-DC Converter becomes the first choice. In the paper, two-channel interleaved two- stage paralleled Buck DC-DC Converter powered by three-phase AC power supply...

  2. Pulsed dc self-sustained magnetron sputtering

    Wiatrowski, A.; Posadowski, W. M.; Radzimski, Z. J.

    2008-01-01

    The magnetron sputtering has become one of the commonly used techniques for industrial deposition of thin films and coatings due to its simplicity and reliability. At standard magnetron sputtering conditions (argon pressure of ∼0.5 Pa) inert gas particles (necessary to sustain discharge) are often entrapped in the deposited films. Inert gas contamination can be eliminated during the self-sustained magnetron sputtering (SSS) process, where the presence of the inert gas is not a necessary requirement. Moreover the SSS process that is possible due to the high degree of ionization of the sputtered material also gives a unique condition during the transport of sputtered particles to the substrate. So far it has been shown that the self-sustained mode of magnetron operation can be obtained using dc powering (dc-SSS) only. The main disadvantage of the dc-SSS process is its instability related to random arc formation. In such case the discharge has to be temporarily extinguished to prevent damaging both the magnetron source and power supply. The authors postulate that pulsed powering could protect the SSS process against arcs, similarly to reactive pulsed magnetron deposition processes of insulating thin films. To put this concept into practice, (i) the high enough plasma density has to be achieved and (ii) the type of pulsed powering has to be chosen taking plasma dynamics into account. In this article results of pulsed dc self-sustained magnetron sputtering (pulsed dc-SSS) are presented. The planar magnetron equipped with a 50 mm diameter and 6 mm thick copper target was used during the experiments. The maximum target power was about 11 kW, which corresponded to the target power density of ∼560 W/cm 2 . The magnetron operation was investigated as a function of pulse frequency (20-100 kHz) and pulse duty factor (50%-90%). The discharge (argon) extinction pressure level was determined for these conditions. The plasma emission spectra (400-410 nm range) and deposition

  3. Modeling, Control and Protection of Low-Voltage DC Microgrids

    Salomonsson, Daniel

    2008-01-01

    Current trends in electric power consumption indicate an increasing use of dc in end-user equipment, such as computers and other electronic appliances used in households and offices. With a dc power system, ac/dc conversion within these loads can be avoided, and losses reduced. AC/DC conversion is instead centralized, and by using efficient, fully controllable power-electronic interfaces, high power quality for both ac and dc systems during steady state and ac grid disturbances can be obtaine...

  4. Operation and control of a DC-grid offshore wind farm under DC transmission system faults

    Deng, Fujin; Chen, Zhe

    2013-01-01

    . Consequently, the protection and control strategies of dc systems need to be established. This paper studies a dc-grid offshore wind farm, where the wind power collection system and power transmission system adopt dc technology. In this paper, the redundancy of the HVDC transmission system under faults...... is studied, and a fault ridethrough strategy for the dc-grid offshore wind farm is proposed. The proposed strategy can effectively minimize the impacts of the power transmission system disturbance on the offshore wind farm, and on the ac grid. A dc-grid offshore wind farm example is simulated with PSCAD....../EMTDC, and the results validate the feasibility of the presented redundancy configuration and operation approach, and the fault ridethrough control strategy....

  5. A suitable model plant for control of the set fuel cell-DC/DC converter

    Andujar, J.M.; Segura, F.; Vasallo, M.J. [Departamento de Ingenieria Electronica, Sistemas Informaticos y Automatica, E.P.S. La Rabida, Universidad de Huelva, Ctra. Huelva - Palos de la Frontera, S/N, 21819 La Rabida - Palos de la Frontera Huelva (Spain)

    2008-04-15

    In this work a state and transfer function model of the set made up of a proton exchange membrane (PEM) fuel cell and a DC/DC converter is developed. The set is modelled as a plant controlled by the converter duty cycle. In addition to allow setting the plant operating point at any point of its characteristic curve (two interesting points are maximum efficiency and maximum power points), this approach also allows the connection of the fuel cell to other energy generation and storage devices, given that, as they all usually share a single DC bus, a thorough control of the interconnected devices is required. First, the state and transfer function models of the fuel cell and the converter are obtained. Then, both models are related in order to achieve the fuel cell+DC/DC converter set (plant) model. The results of the theoretical developments are validated by simulation on a real fuel cell model. (author)

  6. Analysis of DC/DC Converter Efficiency for Energy Storage System Based on Bidirectional Fuel Cells

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    interface to the grid. In power electronics, the converter efficiency is characterized at fixed operating voltage for various output power. This type of characterization is not suitable for fuel cells, since as the power from the fuel cell increases, the cell voltage decreases. This paper analyses how......Renewable energy sources are fluctuating depending on the availability of the energy source. For this reason, energy storage is becoming more important and bidirectional fuel cells represent an attractive technology. Fuel cells require highcurrent low-voltage dc-dc or dc-ac converters as power...... the fuel cell I-V characteristics influences the power electronics converter efficiency and their consequence on the overall system. A loaddependent efficiency curve is presented based on experimental results from a 6 kW dc-dc converter prototype including the most suitable control strategy which maximizes...

  7. Research borehole drilling activity for boreholes DH-18, DH-19, DC-12, DC-13, DC-14, DC-15, and deepening of existing borehole DC-7

    1979-09-01

    This report is an environmental evaluation of the impacts of proposed borehole drilling activities at the Hanford Site, northwest of Richland, Washington. The proposed action is to drill six research boreholes ranging in depth from 137 to 1372 meters (m) [250 to 4500 +- feet (ft)]. In addition, an existing borehole (DC-7) will be extended from 1249 to 1524 m (4099 to 5000 +- ft). The purpose of the US Department of Energy's (DOE) borehole drilling activities is to collect data on in situ rock formations that are considered potentialy suitable for nuclear waste repositories. The technical program efforts necessary to identify and qualify specific underground waste facility sites in candidate rock formations include geologic and hydrologic studies (seismicity and tectonics, rock structure and stratigraphy, lithology, etc.). Borehole drilling is an integral part of the geological studies and is essential to a thorough understanding of potentially suitable geologic formations. The purpose of the proposed drilling activities is to obtain data for evaluating Columbia River basalts that are being evaluated by the National Waste Terminal Storage (NWTS) Program to determine their suitability potential for nuclear waste repositories. Unavoidable impact to the environment is limited primarily to the clearing of land needed for access and drilling operations. Considerations exercised during site preparation, drilling, and subsequent site restoration will limit modification of the natural environment to the minimum required for accomplishment of test objectives

  8. Three phase full wave dc motor decoder

    Studer, P. A. (Inventor)

    1977-01-01

    A three phase decoder for dc motors is disclosed which employs an extremely simple six transistor circuit to derive six properly phased output signals for fullwave operation of dc motors. Six decoding transistors are coupled at their base-emitter junctions across a resistor network arranged in a delta configuration. Each point of the delta configuration is coupled to one of three position sensors which sense the rotational position of the motor. A second embodiment of the invention is disclosed in which photo-optical isolators are used in place of the decoding transistors.

  9. DCMF: DC & Microformats, a good marriage

    Méndez Rodríguez, Eva María; Siches, Arnau; López, Leandro M.; Bravo, Alejandro G.

    2008-01-01

    This report introduces the Dublin Core Microformats (DCMF) project, a new way to use the DC element set within X/HTML. The DC microformats encode explicit semantic expressions in an X/HTML webpage, by using a specific list of terms for values of the attributes “rev” and “rel” for and elements, and “class” and “id” of other elements. Microformats can be easily processed by user agents and software, enabling a high level of interoperability. These characteristics are crucial for the growing n...

  10. Implementation of hierarchical control in DC microgrids

    Jin, Chi; Wang, Peng; Xiao, Jianfang

    2014-01-01

    of Technology, Singapore. The coordination control among multiple dc sources and energy storages is implemented using a novel hierarchical control technique. The bus voltage essentially acts as an indicator of supply-demand balance. A wireless control is implemented for the reliable operation of the grid....... A reasonable compromise between the maximum power harvest and effective battery management is further enhanced using the coordination control based on a central energy management system. The feasibility and effectiveness of the proposed control strategies have been tested by a dc microgrid in WERL....

  11. RF and dc desensitized electroexplosive device

    Krainiak, John W.; Speaks, Paul D.; Cornett, Michael S.

    1989-07-01

    This patent application relates to electroexplosive devices (EEDs) such as detonators, blasting caps and squibs, in particular to a method and device for desensitizing EEDs to electromagnetic radiation and electrostatic charges with the added ability to desensitize the device to essentially dc currents. An insensitive electroexplosive device to electrically ignite explosive is disclosed. This device is inherently immune to radio frequency (RF) radiation, and also provides protection against dc or very low frequency RF induced by arcing. A central feature is use of zeners and capacitors to form a reactively balanced bridge circuit. When constructed in semiconductor form, as described in this application, the device is capable of incorporation in small caliber ordnance.

  12. DC Motor Drive with PFC Rectifier

    Lascu Mihaela

    2008-05-01

    Full Text Available The goal of this work is to study theperformances of a hybrid controller used to controlDC Motor drive with a single-phase power factorcorrection rectifier. This study is made usingcomputer simulation (Simulink. The first part isdevoted to the control system of the DC Motors. Inthe second part, the design of the hybrid controllerwill be presented. The third part is the design ofthe fast response single-phase boost power factorcorrection rectifier. The last parts are devoted tosimulation and experimental results.

  13. Stability analysis of a high-step-Up DC grid-connected two-stage boost DC-DC converter

    El Aroudi A.

    2014-01-01

    Full Text Available High conversion ratio switching converters are used whenever there is a need to step-up dc source voltage level to a much higher output dc voltage level such as in photovoltaic systems, telecommunications and in some medical applications. A simple solution for achieving this high conversion ratio is by cascading different stages of dc-dc boost converters. The individual converters in such a cascaded system are usually designed separately applying classical design criteria. However these criteria may not be applicable for the complete cascaded system . This paper first presents a glimpse on the bifurcation behavior that a cascade connection of two boost converters can exhibit. It is shown that the desired periodic orbit can undergo period doubling leading to subharmonic oscillations and chaotic regimes. Then, in order to simplify the analysis the second stage is considered as constant current sink and design-oriented analysis is carried out to obtain stability boundaries in the parameter space by taking into account slope interactions between the state variables in the two-different stages.

  14. Design and modelling of high gain DC-DC converters for fuel cell hybrid electric vehicles

    Elangovan, D.; Karthigeyan, V.; Subhanu, B.; Ashwin, M.; Arunkumar, G.

    2017-11-01

    Transportation (Diesel and petrol internal combustion engine vehicles) approximately contributes to 25.5% of total CO2 emission. Thus diesel and petrol engine vehicles are the most dominant contributors of CO2 emission which leads global warming which causes climate change. The problem of CO2 emission and global warming can be reduced by focusing on renewable energy vehicles. Out of the available renewable energy sources fuel cell is the only source which has reasonable efficiency and can be used in vehicles. But the main disadvantage of fuel cell is its slow response time. So energy storage systems like batteries and super capacitors are used in parallel with the fuel cell. Fuel cell is used during steady state vehicle operation while during transient conditions like starting, acceleration and braking batteries and super capacitors can supply or absorb energy. In this paper a unidirectional fuel cell DC-DC converter and bidirectional energy storage system DC-DC converter is proposed, which can interface dc sources at different voltage levels to the dc bus and also it can independently control the power flow from each energy source to the dc bus and vice versa. The proposed converters are designed and simulated using PSIM version 9.1.1 and gate pulse pattern, input and output voltage waveforms of the converters for steady state operation are studied.

  15. Homopolar dc motor and trapped flux brushless dc motor using high temperature superconductor materials

    Crapo, Alan D.; Lloyd, Jerry D.

    1991-03-01

    Two motors have been designed and built for use with high-temperature superconductor (HTSC) materials. They are a homopolar dc motor that uses HTSC field windings and a brushless dc motor that uses bulk HTSC materials to trap flux in steel rotor poles. The HTSC field windings of the homopolar dc motor are designed to operate at 1000 A/sq cm in a 0.010-T field. In order to maximize torque in the homopolar dc motor, an iron magnetic circuit with small air gaps gives maximum flux for minimum Ampere turns in the field. A copper field winding version of the homopolar dc motor has been tested while waiting for 575 A turn HTSC coils. The trapped flux brushless dc motor has been built and is ready to test melt textured bulk HTSC rings that are currently being prepared. The stator of the trapped flux motor will impress a magnetic field in the steel rotor poles with warm HTSC bulk rings. The rings are then cooled to 77 K to trap the flux in the rotor. The motor can then operate as a brushless dc motor.

  16. Comparison of solar panel cooling system by using dc brushless fan and dc water

    Irwan, Y M; Leow, W Z; Irwanto, M; M, Fareq; Hassan, S I S; Amelia, A R; Safwati, I

    2015-01-01

    The purpose of this article is to discuss comparison of solar panel cooling system by using DC brushless fan and DC water pump. Solar photovoltaic (PV) power generation is an interesting technique to reduce non-renewable energy consumption and as a renewable energy. The temperature of PV modules increases when it absorbs solar radiation, causing a decrease in efficiency. A solar cooling system is design, construct and experimentally researched within this work. To make an effort to cool the PV module, Direct Current (DC) brushless fan and DC water pump with inlet/outlet manifold are designed for constant air movement and water flow circulation at the back side and front side of PV module representatively. Temperature sensors were installed on the PV module to detect temperature of PV. PIC microcontroller was used to control the DC brushless fan and water pump for switch ON or OFF depend on the temperature of PV module automatically. The performance with and without cooling system are shown in this experiment. The PV module with DC water pump cooling system increase 3.52%, 36.27%, 38.98%in term of output voltage, output current, output power respectively. It decrease 6.36 °C compare than to PV module without DC water pump cooling system. While DC brushless fan cooling system increase 3.47%, 29.55%, 32.23%in term of output voltage, output current, and output power respectively. It decrease 6.1 °C compare than to PV module without DC brushless fan cooling system. The efficiency of PV module with cooling system was increasing compared to PV module without cooling system; this is because the ambient temperature dropped significantly. The higher efficiency of PV cell, the payback period of the system can be shorted and the lifespan of PV module can also be longer. (paper)

  17. Transition towards DC micro grids: From an AC to a hybrid AC and DC energy infrastructure

    Evi Ploumpidou

    2017-12-01

    Full Text Available Our electricity is predominantly powered by alternating current (AC, ever since the War of Currents ended in the favor of Nicola Tesla at the end of the 19th century. However, lots of the appliances we use, such as electronics and lights with light-emitting diode (LED technology, work internally on direct current (DC and it is projected that the number of these appliances will increase in the near future. Another contributor to the increase in DC consumption is the ongoing electrification of mobility (Electric Vehicles (EVs. At the same time, photovoltaics (PV generate DC voltages, while the most common storage technologies also use DC. In order to integrate all these appliances and technologies to the existing AC grid, there is a need for converters which introduce power losses. By distributing DC power to DC devices instead of converting it to AC first, it is possible to avoid substantial energy losses that occur every time electricity is converted. This situation initiated the concept for the implementation of the DC-Flexhouse project. A prototype DC installation will be developed and tested in one of the buildings of the developing living lab area called the District of Tomorrow (De Wijk van Morgen which is located in Heerlen, the Netherlands. A neighborhood cooperative (Vrieheide cooperatie is also part of the consortium in order to address the aspect of social acceptance. Although DC seems to be a promising solution for a more sustainable energy system, the business case is still debatable due to both technology- and market-related challenges. The current energy infrastructure is predominantly based on AC, manufacturers produce devices based on AC standards and people are using many AC products across a long life span. This Smart Energy Buildings & Cities (SEB&C PDEng project is a contribution to the DC-Flexhouse project. The aim is to analyze the challenges in the transition to DC micro grids, assess the market potential of DC

  18. Properties of DLC coatings deposited by dc and dc with superimposed pulsed vacuum arc

    Zavaleyev, V.; Walkowicz, J.; Aksyonov, D.S.; Luchaninov, A.A.; Reshetnyak, E.N.; Strel'nitskij, V.E.

    2014-01-01

    Comparative studies of the structure, mechanical and tribological properties of DLC coatings deposited in DC and DC with superimposed high current pulse modes of operation vacuum-arc plasma source with the graphite cathode are presented. Imposition the pulses of high current on DC vacuum-arc discharge allows both increase the deposition rate of DLC coating and reduce the residual compressive stress in the coatings what promotes substantial improvement the adhesion to the substrate. Effect of vacuum arc plasma filtration with Venetian blind filter on the deposition rate and tribological characteristics of the coatings analyzed.

  19. Hierarchical Control for Multiple DC-Microgrids Clusters

    Shafiee, Qobad; Dragicevic, Tomislav; Vasquez, Juan Carlos

    2014-01-01

    DC microgrids (MGs) have gained research interest during the recent years because of many potential advantages as compared to the ac system. To ensure reliable operation of a low-voltage dc MG as well as its intelligent operation with the other DC MGs, a hierarchical control is proposed in this p......DC microgrids (MGs) have gained research interest during the recent years because of many potential advantages as compared to the ac system. To ensure reliable operation of a low-voltage dc MG as well as its intelligent operation with the other DC MGs, a hierarchical control is proposed...

  20. Modeling and simulation for micro DC motor based on simulink

    Shen, Hanxin; Lei, Qiao; Chen, Wenxiang

    2017-09-01

    The micro DC motor has a large market demand but there is a lack of theoretical research for it. Through detailed analysis of the commutation process of micro DC motor commutator, based on micro DC motor electromagnetic torque equation and mechanical torque equation, with the help of Simulink toolkit, a triangle connection micro DC motor simulation model is established. By using the model, a sample micro DC motor are simulated, and an experimental measurements has been carried on the sample micro DC motor. It is found that the simulation results are consistent with theoretical analysis and experimental results.

  1. Power Quality in DC Power Distribution Systems and Microgrids

    Stephen Whaite

    2015-05-01

    Full Text Available This review paper discusses power quality considerations for direct current (DC electric power distribution systems, particularly DC microgrids. First, four selected sample DC architectures are discussed to provide motivation for the consideration of power quality in DC systems. Second, a brief overview of power quality challenges in conventional alternating current (AC distribution systems is given to establish the field of power quality. Finally, a survey of literature addressing power quality issues in DC systems is presented, and necessary power quality considerations in DC distribution system design and operation are discussed.

  2. Halbach array DC motor/generator

    Merritt, B.T.; Dreifuerst, G.R.; Post, R.F.

    1998-01-06

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An ``inside-out`` design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then ``switched`` or ``commutated`` to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives. 17 figs.

  3. Double-barrier junction based dc SQUID

    Bartolomé, M.E.; Brinkman, Alexander; Flokstra, Jakob; Golubov, Alexandre Avraamovitch; Rogalla, Horst

    2000-01-01

    dc SQUIDs based on double-barrier Nb/Al/AlOx/Al/AlOx/Al/Nb junctions (DBSQs) have been fabricated and tested for the first time. The current–voltage curves have been measured at temperatures down to 1.4 K. The critical current, Ic, dependence on the temperature T is partially described by the

  4. What should your DC default be?

    Cui, J.

    2009-01-01

    As reported, most DC pension scheme participants simply follow proposed defaults, even though they have the freedom to choose. Consequently, default designs have dramatic impacts on individuals’retirement saving outcomes. Given the fact that the default design matters, this paper evaluates

  5. Hierarchical Control for Multiple DC Microgrids Clusters

    Shafiee, Qobad; Dragicevic, Tomislav; Vasquez, Juan Carlos

    2014-01-01

    This paper presents a distributed hierarchical control framework to ensure reliable operation of dc Microgrid (MG) clusters. In this hierarchy, primary control is used to regulate the common bus voltage inside each MG locally. An adaptive droop method is proposed for this level which determines...

  6. Voltage control of DC islanded microgrids

    Tucci, Michele; Riverso, Stefano; Quintero, Juan Carlos Vasquez

    2015-01-01

    We propose a new decentralized control scheme for DC Islanded microGrids (ImGs) composed by several Distributed Generation Units (DGUs) with a general interconnection topology. Each local controller regulates to a reference value the voltage of the Point of Common Coupling (PCC...

  7. Halbach array DC motor/generator

    Merritt, Bernard T.; Dreifuerst, Gary R.; Post, Richard F.

    1998-01-01

    A new configuration of DC motor/generator is based on a Halbach array of permanent magnets. This motor does not use ferrous materials so that the only losses are winding losses and losses due to bearings and windage. An "inside-out" design is used as compared to a conventional motor/generator design. The rotating portion, i.e., the rotor, is on the outside of the machine. The stationary portion, i.e., the stator, is formed by the inside of the machine. The rotor contains an array of permanent magnets that provide a uniform field. The windings of the motor are placed in or on the stator. The stator windings are then "switched" or "commutated" to provide a DC motor/generator much the same as in a conventional DC motor. The commutation can be performed by mechanical means using brushes or by electronic means using switching circuits. The invention is useful in electric vehicles and adjustable speed DC drives.

  8. Gravity Compensation Technique Uses Small dc Motor

    Hollow, Richard

    1988-01-01

    Small dc servomotor powered by simple constant-current source and with suitable gearing used to cancel effect of gravity upon load. Lead-screw positioning system has load counterbalanced by small supplementary motor powered by constant current source. Motor lighter and more compact alternative to counterbalance. Used in variety of mechanical systems where load positioned or accelerated in vertical plane.

  9. Computerized Torque Control for Large dc Motors

    Willett, Richard M.; Carroll, Michael J.; Geiger, Ronald V.

    1987-01-01

    Speed and torque ranges in generator mode extended. System of shunt resistors, electronic switches, and pulse-width modulation controls torque exerted by large, three-phase, electronically commutated dc motor. Particularly useful for motor operating in generator mode because it extends operating range to low torque and high speed.

  10. DC photoemission electron guns as ERL sources

    Sinclair, Charles K.

    2006-01-01

    Very-high-voltage DC electron guns, delivering moderate duration bunches from photoemission cathodes, and followed by conventional drift bunching and acceleration, offer a practical solution for an ERL injector. In a variant of this scheme, a DC gun is placed in close proximity to a superconducting RF accelerator cavity, with few or no active elements between the gun and cavity. The principal technical challenge with such electron guns arises from field emission from the cathode electrode and its support structure. Field emission may result in voltage breakdown across the cathode-anode gap, or a punch-through failure of the insulator holding off the cathode potential, as well as lesser though still serious problems. Various means to mitigate these problems are described. The operational lifetime of high quantum efficiency photocathodes in these guns is determined by the vacuum conditions, through phenomena such as chemical poisoning and ion back-bombardment. Minimization of the field strength on electrode structures pushes high-voltage DC guns toward large dimensions and, correspondingly, large outgassing loads, but it is also true that these guns offer many opportunities for achieving excellent vacuum conditions. Good solutions to vacuum problems that had previously limited cathode lifetime have been demonstrated in recent years. Designs for DC guns presently in use and planned for the near future will be described. The parameters necessary for a 100 mA average current, very-high-voltage DC gun with a photocathode operational lifetime greater than 100 h appear to be within reach, but have yet to be demonstrated. A 1 A average current source with good cathode operational lifetime will require developments beyond the present state-of-the-art

  11. Current Mode Control for LLC Series Resonant DC-to-DC Converters

    Jinhaeng Jang

    2015-06-01

    Full Text Available Conventional voltage mode control only offers limited performance for LLC series resonant DC-to-DC converters experiencing wide variations in operational conditions. When the existing voltage mode control is employed, the closed-loop performance of the converter is directly affected by unavoidable changes in power stage dynamics. Thus, a specific control design optimized at one particular operating point could become unacceptable when the operational condition is varied. This paper presents a new current mode control scheme which could consistently provide good closed-loop performance for LLC resonant converters for the entire operational range. The proposed control scheme employs an additional feedback from the current of the resonant tank network to overcome the limitation of the existing voltage mode control. The superiority of the proposed current mode control over the conventional voltage mode control is verified using an experimental 150 W LLC series resonant DC-to-DC converter.

  12. DC-DC power converter research for Orbiter/Station power exchange

    Ehsani, M.

    1993-01-01

    This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented.

  13. Differential Mode EMI Filter Design for Isolated DC-DC Boost Converter

    Makda, Ishtiyaq Ahmed; Nymand, Morten

    2014-01-01

    A Differential Mode EMI filter for a low input voltage high-current isolated dc-dc boost converter is designed and presented in this paper. The primary side Differential Mode noise voltage is low due to the high transformer turn ratio, however, the input current is very high and since the EMI limit...... also does not change for such converters, it requires greatly optimized design approach for the filter including the correct sizing of the filter components. A complete analytical filter design process is carried out such a way that the Differential Mode noise voltage source in the converter...... is identified first. The DM noise model is then established and based on the harmonic analysis of the noise source voltage waveform, the complete Differential Mode EMI filter, including the filter resonance damping branch, is designed for a 3kW isolated dc-dc boost converter. The noise model and its theoretical...

  14. Multi-level cascaded DC/DC converters for PV applications

    Ahmed A.A. Hafez

    2015-12-01

    Full Text Available A robust multi-level cascaded DC/DC system for Photovoltaic (PV application is advised in this article. There are three PV generators, each is coupled to a half-bridge buck cell. Each PV-generator–buck-converter channel is controlled such that maximum power is captured independently under different irradiation and temperature levels. The system operation under normal and abnormal conditions was comprehensively investigated. Internal Model Control (IMC technique was adopted for tuning the controllers. An elaborate switching modulation strategy was used to reduce the current ripple and inductor size, while maintaining high efficiency. Annotative, simple and robust remedial strategies were proposed to mitigate different anticipated faults. Comprehensive simulation results in Matlab environment were illustrated for corroborating the performance of the advised cascaded DC/DC system under normal/abnormal conditions. The proposed system enjoys the merits of independency, reduced volumetric dimensions and improved efficiency. Furthermore, the system is inherently fault-tolerant.

  15. High Voltage Coil Current Sensor for DC-DC Converters Employing DDCC

    M. Drinovsky

    2015-12-01

    Full Text Available Current sensor is an integral part of every switching converter. It is used for over-current protection, regulation and in case of multiphase converters for balancing. A new high voltage current sensor for coil-based current sensing in DC-DC converters is presented. The sensor employs DDCC with high voltage input stage and gain trimming. The circuit has been simulated and implemented in 0.35 um BCD technology as part of a multiphase DC-DC converter where its function has been verified. The circuit is able to sustain common mode voltage on the input up to 40 V, it occupies 0.387*0.345 mm2 and consumes 3.2 mW typically.

  16. Analysis of the Coupling Behavior of PEM Fuel Cells and DC-DC Converters

    Achim Kienle

    2009-03-01

    Full Text Available The connection between PEM fuel cells and common DC-DC converters is examined. The analysis is model-based and done for boost, buck and buck-boost converters. In a first step, the effect of the converter ripples upon the PEM fuel cell is shown. They introduce oscillations in the fuel cell. Their appearance is explained, discussed and possibilities for their suppression are given. After that, the overall behaviors of the coupled fuel cell-converter systems are analyzed. It is shown, that neither stationary multiplicities nor oscillations can be introduced by the couplings and therefore separate control approaches for both the PEMFC and the DC-DC converters are applicable.

  17. Integrated Three-Port DC-DC Converter for Photovoltaic (PV) Battery Stand-alone Systems

    Ouyang, Ziwei; Andersen, Michael A. E.

    2016-01-01

    of solar energy. Moreover, a novel transformer configuration enables variable turns ratio controlled by the phase between the two current excitations subjected to the primary windings, allowing a wider input/output range. 1 kW experimental prototype has been built to demonstrate a wellmanaged power flow......Several power sources such as PV solar arrays and battery are often used to manage the power flow for a photovoltaic (PV) based stand-alone power system due to the fluctuation nature of solar energy resource, and deliver a continuous power to the users in an appropriate form. Traditionally, three...... different single-input single-output (SISO) dc/dc converters would have been used. To reduce the cost and improve the power density of the system, an integrated three-port isolated dc/dc converter is proposed in this paper. It can realize all functions of the energy delivery due to the fluctuation nature...

  18. single-phase dc phase dc-ac boost converter ac boost converter

    User

    systems, need to step-up the DC input voltage. increase the ... design also makes for extra parts, greater system and weight, [1-3]. ... proposes a new design for high performance sin ... SYSTEM ANALYSIS. 2. ..... from the simulation study.

  19. Y-source impedance-network-based isolated boost DC/DC converter

    Siwakoti, Yam P.; Town, Graham; Loh, Poh Chiang

    2014-01-01

    A dc-dc converter with very high voltage gain is proposed in this paper for any medium-power application requiring a high voltage boost with galvanic isolation. The proposed converter topology can be realized using only two switches. With this topology a very high voltage boost can be achieved even...... with a relatively low duty cycle of the switches, and the gain obtainable is presently not matched by any existing impedance network based converter operated at the same duty ratio. The proposed converter has a Y-source impedance network to boost the voltage at the intermediate dc-link side and a push......-pull transformer for square-wave AC inversion and isolation. The voltage-doubler rectifier provides a constant dc voltage at the output stage. A theoretical analysis of the converter is presented, supported by simulation and experimental results. A 250 W down-scaled prototype was implemented in the laboratory...

  20. SUBCONTRACT REPORT: DC-DC Converter for Fuel Cell and Hybrid Vehicles

    Marlino, Laura D [ORNL; Zhu, Lizhi [Ballard Power Systems/Siemens VDO

    2007-07-01

    The goal of this project is to develop and fabricate a 5kW dc-dc converter with a baseline 14V output capability for fuel cell and hybrid vehicles. The major objectives for this dc-dc converter technology are to meet: Higher efficiency (92%); High coolant temperature,e capability (105 C); High reliability (15 Years/150,000miles); Smaller volume (5L); Lower weight (6kg); and Lower cost ($75/kW). The key technical challenge for these converters is the 105 C coolant temperatures. The power switches and magnetics must be designed to sustain these operating temperatures reliably, without a large cost/mass/volume penalty.

  1. Washington DC Metropolitan Area Drug Study Household and Non-Household Populations (DC-MADSH-1991)

    U.S. Department of Health & Human Services — The DC Metropolitan Area Drug Study (DCMADS) was conducted in 1991, and included special analyses of homeless and transient populations and of women delivering live...

  2. Circuit description of unipolar DC-to-DC converters for APS storage ring quadrupoles and sextupoles

    McGhee, D.G.

    1993-01-01

    This paper describes the control, interlock, and power circuits for 680 unipolar switch mode DC-to-DC converters used to regulate the Advanced Photon Sources (APS's) storage ring quadrupole and sextupole magnet currents. Quadrupole current stability is ± 6x10 -5 and the sextupole current stability is ±3x10 -4 . The stability is obtained with pulse width modulation, operating at a switching frequency of 20kHz with full current switching. The converters are housed in 200 cabinets located on top of the storage ring tunnel. Raw DC power is distributed from 80 AC-to-DC power supplies, four at each of 20 locations around the storage ring. Voltages, currents, and temperatures are computer monitored and logged for the converters and magnets. All converters and magnets are water cooled with the flow and pressure monitored at the inlet and outlet of groups. Water is interlocked with the raw power supplies and not the individual converters

  3. Research of digital controlled DC/DC converter based on STC12C5410AD

    Chen, Dan-Jiang; Jin, Xin; Xiao, Zhi-Hong

    2010-02-01

    In order to study application of digital control technology on DC/DC converter, principle of increment mode PID control algorithm was analyzed in the paper. Then, a SCM named STC12C5410AD was introduced with its internal resources and characteristics. The PID control algorithm can be implemented easily based on it. The output of PID control was used to change the value of a variable that is 255 times than duty cycle, and this reduced the error of calculation. The valid of the presented algorithm was verified by an experiment for a BUCK DC/DC converter. The experimental results indicated that output voltage of the BUCK converter is stable with low ripple.

  4. Washington DC Metropolitan Area Drug Study Homeless and Transient Population (DC-MADST-1991)

    U.S. Department of Health & Human Services — The DC Metropolitan Area Drug Study (DCMADS) was conducted in 1991, and included special analyses of homeless and transient populations and of women delivering live...

  5. Improvement of burst-mode control of piezoelectric transformer based DC/DC converter

    Vasic, Dejan; Liu, Yuan-Ping; Costa, François; Schwander, Denis; Wu, Wen-Jong

    2013-01-01

    Burst-mode operation is adopted sometimes in piezoelectric transformer based converters for two major purposes: (1) to achieve voltage regulation in DC/DC converters and (2) to achieve dimming control in backlight inverters. Burst-mode control enables the converter to operate at a constant switching frequency as well as to maintain good efficiency at light load conditions. However, in practice, the piezoelectric transformer cannot instantly stop vibrating in the burst-mode due to its high quality factor. The delay in the output voltage change resulting from this behavior influences the accuracy of the regulation. This paper proposes a control strategy to make the piezoelectric transformer stop more quickly so as to enhance the accuracy of burst-mode control. The proposed method only modifies the control signal of the burst-mode driving circuit. The proposed control strategy is verified by experiments in a step-down 9 W DC/DC converter. (paper)

  6. Current Mode Control for LLC Series Resonant DC-to-DC Converters

    Jinhaeng Jang; Syam Kumar Pidaparthy; Byungcho Choi

    2015-01-01

    Conventional voltage mode control only offers limited performance for LLC series resonant DC-to-DC converters experiencing wide variations in operational conditions. When the existing voltage mode control is employed, the closed-loop performance of the converter is directly affected by unavoidable changes in power stage dynamics. Thus, a specific control design optimized at one particular operating point could become unacceptable when the operational condition is varied. This paper presents a...

  7. LPV model for PV cell and fractional control of DC/DC converter for photovoltaic systems

    Martínez González, Rubén; Bolea Monte, Yolanda; Grau Saldes, Antoni; Martínez García, Herminio

    2011-01-01

    This paper deals with the fractional modelling of a DC-DC converter, suitable in solar-powered electrical generation systems, and the design of a fractional controller for the aforementioned switching converter. A new model for PV cells is proposed in order to obtain a linear equation for V-I characteristic via scheduling dependence of temperature and irradiance. Due to the fractional nature of the ultracapacitors this kind of controller gives a suitable and good performance. Peer Reviewed

  8. LPV model for PV cells and fractional control of DC/DC converter for photovoltaic systems

    Martínez González, Rubén; Bolea Monte, Yolanda; Grau Saldes, Antoni; Martínez García, Herminio

    2011-01-01

    This paper deals with the fractional modelling of a DC-DC converter, suitable in solar-powered electrical generation systems, and the design of a fractional controller for the aforementioned switching converter. A new model for PV cells is proposed in order to obtain a linear equation for VI characteristic via scheduling dependence of temperature and irradiance. Due to the fractional nature of the ultracapacitors this kind of controller gives a suitable and good performance. Peer Rev...

  9. Distributed maximum power point tracking in photovoltaic applications: active bypass DC/DC converter

    Carlos Andrés Ramos-Paja

    2012-01-01

    Full Text Available Se propone una estructura de desvío activo para maximizar la producción de potencia en sistemas fotovoltaicos bajo condiciones irregulares de operación, comparando su eficiencia con soluciones individuales y distribuidas basadas en convertidores DC/DC convencionales. Los análisis y simulaciones realistas demuestran las ventajas del nuevo convertidor de desvío activo sobre soluciones basadas en convertidores Boost, Buck y Buck-Boost.

  10. Analisa Perbandingan Efisiensi Motor Dc Kompon Pendek Dengan Motor Dc Kompon Panjang Akibat Penambahan Kutub

    Sitompul, Fuad Rahim

    2015-01-01

    Motor listrik merupakan perangkat elekromagnetis yang mengubah energi listrik menjadi energi mekanik. Motor DC memerlukan tegangan searah pada kumparan medan untuk diubah menjadi energi mekanik. Energi mekanik ini digunakan sebagai penggerak peralatan listrik seperti pompa,penggerak kipas angin, lift dan lain-lain. Karena penggunaannya yang cukup luas maka kinerjanya harus baik. Kinerja suatu motor DC dikatakan baik jika efisiensi motor tersebut tinggi. Hal itu dapat dicapai dengan mengatur b...

  11. Soft switching bidirectional DC-DC converter for ultracapacitor-batteries interface

    Adib, Ehsan; Farzanehfard, Hosein

    2009-01-01

    In this paper a new soft switching bidirectional DC-DC converter is introduced which can be applied as the interface circuit between ultracapacitors and batteries or fuel cells. All semiconductor devices in the proposed converter are soft switched while the control circuit remains PWM. Due to achieved soft switching condition, the energy conversion through the proposed converter is highly efficient. The proposed converter is analyzed and a prototype converter is implemented. The presented experimental results confirm the theoretical analysis.

  12. Soft switching bidirectional DC-DC converter for ultracapacitor-batteries interface

    Adib, Ehsan; Farzanehfard, Hosein [Dept. of Electrical and Computer Engineering, Isfahan Univ. of Technology (Iran)

    2009-12-15

    In this paper a new soft switching bidirectional DC-DC converter is introduced which can be applied as the interface circuit between ultracapacitors and batteries or fuel cells. All semiconductor devices in the proposed converter are soft switched while the control circuit remains PWM. Due to achieved soft switching condition, the energy conversion through the proposed converter is highly efficient. The proposed converter is analyzed and a prototype converter is implemented. The presented experimental results confirm the theoretical analysis. (author)

  13. Comparative efficiency evaluation of buck and hybrid buck DC-DC converters for automotive applications

    Pelan, Ovidiu; Cornea, Octavian; Muntean, Nicolae

    2014-01-01

    This paper presents and discusses design considerations and efficiency investigation of a conventional step-down and a hybrid switched-capacitor DC-DC converter. Three MOSFETs with low on-resistance have been tested for each converter in order to find the most adequate switch for this application....... The experimental results and comparative efficiency graphs were obtained with a 1kW laboratory prototype dedicated for a 42/14V dual voltage automotive system....

  14. Simulating and Testing a DC-DC Half-Bridge SLR Converter

    2013-06-01

    future pulse power demands with ship power, a large bank of capacitors or similar rapid discharge source is required. If capacitors are charged...Single Pulsed Avalanche Energy (j) I" Avalanche Current (i) E,, Repetilive Avalanche Energy (i) dv/dt Peak Diode Recovery dv/dt ® Po Total Power...SLR), battery charging, DC-DC, pulse power, power electronics, SLR converter 15. NUMBER OF PAGES 119 16. PRICE CODE 17. SECURITY CLASSIFICATION

  15. Sliding-mode control of single input multiple output DC-DC converter

    Zhang, Libo; Sun, Yihan; Luo, Tiejian; Wan, Qiyang

    2016-10-01

    Various voltage levels are required in the vehicle mounted power system. A conventional solution is to utilize an independent multiple output DC-DC converter whose cost is high and control scheme is complicated. In this paper, we design a novel SIMO DC-DC converter with sliding mode controller. The proposed converter can boost the voltage of a low-voltage input power source to a controllable high-voltage DC bus and middle-voltage output terminals, which endow the converter with characteristics of simple structure, low cost, and convenient control. In addition, the sliding mode control (SMC) technique applied in our converter can enhance the performances of a certain SIMO DC-DC converter topology. The high-voltage DC bus can be regarded as the main power source to the high-voltage facility of the vehicle mounted power system, and the middle-voltage output terminals can supply power to the low-voltage equipment on an automobile. In the respect of control algorithm, it is the first time to propose the SMC-PID (Proportion Integration Differentiation) control algorithm, in which the SMC algorithm is utilized and the PID control is attended to the conventional SMC algorithm. The PID control increases the dynamic ability of the SMC algorithm by establishing the corresponding SMC surface and introducing the attached integral of voltage error, which endow the sliding-control system with excellent dynamic performance. At last, we established the MATLAB/SIMULINK simulation model, tested performance of the system, and built the hardware prototype based on Digital Signal Processor (DSP). Results show that the sliding mode control is able to track a required trajectory, which has robustness against the uncertainties and disturbances.

  16. Informational model verification of ZVS Buck quasi-resonant DC-DC converter

    Vakovsky, Dimiter; Hinov, Nikolay

    2016-12-01

    The aim of the paper is to create a polymorphic informational model of a ZVS Buck quasi-resonant DC-DC converter for the modeling purposes of the object. For the creation of the model is applied flexible open standards for setting, storing, publishing and exchange of data in distributed information environment. The created model is useful for creation of many and different by type variants with different configuration of the composing elements and different inner model of the examined object.

  17. ITAR Free Commercial-of-the-Shelf DC/DC Converter

    Denzinger, Wolfgang; Hintze, Thomas

    2014-08-01

    A commercial-of-the-shelf (COTS) DC/DC converter for digital space equipment has been developed by ASP under ESA contract with special emphasis on low cost, no use of ITAR listed EEE parts like Mosfets, minimum number of rad-hard digital IC's and a design tolerance against single event effects by appropriate filtering. However, the intention to qualify this discrete converter design for a low cost FM series production was difficult due to the high up-sceening cost of EEE-parts with one lot guarantee and minimum-by. To overcome this problem, in a next step a redesign of the DC/DC converter was performed with all semiconductors like bipolar transistors, rectifiers and zener diodes packaged into hybrids. With this approach it was possible to buy a high number of less expensive wafers or dies from one lot, to perform a lot acceptance test and to integrate the dies into hybrid packages with further up- screening for FM use. The semiconductors have been packaged into three signal hybrids with 44 pins and one power hybrid with 24 pins for the dissipating transistors and rectifiers. The design of the hybrids is such, that all integrated semiconductors can be tested individually. The qualification of four EQM DC/DC converters with different combinations of output voltages has been successfully performed and two FM's have been manufactured and tested.

  18. Design and implementation of current fed DC-DC converter for PHEV application using renewable source

    Milind Metha, Manish; Tutki, Sanjay; Rajan, Aju; Elangovan, D.; Arunkumar, G.

    2017-11-01

    As the fossil fuels are depleting day by day, the use of renewable energy sources came into existence and they evolved a lot lately. To increase efficiency and productivity in the hybrid vehicles, the existence less efficient petroleum and diesel IC engines need to be replaced with the new and efficient converters with renewable energy sources. This has to be done in such a way that impacts three factors mainly: cost, efficiency and reliability. The PHEVs that have been launched and the upcoming PHEVs using converters with voltage range around 380V to 400V generated with power ranges between 2.4KW to 2.8KW. The basic motto of this paper is to design a prolific converter while considering the factor such as cost and size. In this paper, a two stage DC-DC converter is proposed and the proposed DC-DC converter is utilized to endeavour voltage from 24V (photovoltaic source) to a yield voltage of 400V and to meet the power demand of 250W, since only one panel is being used for this proposed paper. This paper discuss in detail about why and how the current fed DC-DC converter is utilized along with a voltage doubler, thus reducing transformer turns and thereby reducing overall size of the product. Simulation and hardware results have been presented along with calculations for duty cycle required for firing sequence for different values of transformer turns.

  19. CAMEX-4 DC-8 DROPSONDE SYSTEM V1

    National Aeronautics and Space Administration — The CAMEX-4 DC-8 Dropsonde System dataset was collected by the DC-8 Dropsonde System (D8D) uses dropwindsonde and Global Positioning System (GPS) receivers to...

  20. control of a dc motor using fuzzy logic control algorithm

    user

    controller in the control performance of an industrial type DC motor using MATLAB. The fuzzy logic .... controlled separately excited permanent magnet DC motor (PMDC). ... When the field current is constant, the flux induced by the field ...

  1. Brushless dc motor uses electron beam switching tube as commutator

    Studer, P.

    1965-01-01

    Electron beam switching tube eliminates physical contact between rotor and stator in brushless dc motor. The tube and associated circuitry control the output of a dc source to sequentially energize the motor stator windings.

  2. Trends and determinants of cycling in the Washington, DC region.

    2011-01-01

    This report analyzes cycling trends, policies, and commuting in the Washington, DC area. The analysis is divided into two parts. : Part 1 focuses on cycling trends and policies in Washington (DC), Alexandria (VA), Arlington County (VA), Fairfax Count...

  3. Design of an Input-Parallel Output-Parallel LLC Resonant DC-DC Converter System for DC Microgrids

    Juan, Y. L.; Chen, T. R.; Chang, H. M.; Wei, S. E.

    2017-11-01

    Compared with the centralized power system, the distributed modularized power system is composed of several power modules with lower power capacity to provide a totally enough power capacity for the load demand. Therefore, the current stress of the power components in each module can then be reduced, and the flexibility of system setup is also enhanced. However, the parallel-connected power modules in the conventional system are usually controlled to equally share the power flow which would result in lower efficiency in low loading condition. In this study, a modular power conversion system for DC micro grid is developed with 48 V dc low voltage input and 380 V dc high voltage output. However, in the developed system control strategy, the numbers of power modules enabled to share the power flow is decided according to the output power at lower load demand. Finally, three 350 W power modules are constructed and parallel-connected to setup a modular power conversion system. From the experimental results, compared with the conventional system, the efficiency of the developed power system in the light loading condition is greatly improved. The modularized design of the power system can also decrease the power loss ratio to the system capacity.

  4. DC-DC Type High-Frequency Link DC for Improved Power Quality of Cascaded Multilevel Inverter

    Sadikin, Muhammad; Senjyu, Tomonobu; Yona, Atsushi

    2013-06-01

    Multilevel inverters are emerging as a new breed of power converter options for power system applications. Recent advances in power switching devices enabled the suitability of multilevel inverters for high voltage and high power applications because they are connecting several devices in series without the need of component matching. Usually, a transformerless battery energy storage system, based on a cascaded multilevel inverter, is used as a measure for voltage and frequency deviations. System can be reduced in size, weight, and cost of energy storage system. High-frequency link circuit topology is advantageous in realizing compact and light-weight power converters for uninterruptible power supply systems, new energy systems using photovoltaic-cells, fuel-cells and so on. This paper presents a DC-DC type high-frequency link DC (HFLDC) cascaded multilevel inverter. Each converter cell is implemented a control strategy for two H-bridge inverters that are controlled with the same multicarrier pulse width modulation (PWM) technique. The proposed cascaded multilevel inverter generates lower voltage total harmonic distortion (THD) in comparison with conventional cascaded multilevel inverter. Digital simulations are carried out using PSCAD/EMTDC to validate the performance of the proposed cascaded multilevel inverter.

  5. Unregulated Series Resonant Converter for Interlinking DC Nanogrids

    Tomas Manez, Kevin; Zhang, Zhe; Ouyang, Ziwei

    2017-01-01

    bidirectional converter to interlink a 400V DC bus with a 48V DC bus ispresented. The proposed converter is based on a LLC resonant converter operating as a DC transformer at a fixed frequency and duty cycle without any complex control strategy. A clearand simplified design procedure for high efficiency...

  6. Controller design and stability analysis of grid connected DC microgrid

    Chauhan, Rajeev Kumar; Chauhan, Kalpana; Guerrero, Josep M.

    2018-01-01

    DC microgrids are desired to provide the electricity for the remote areas which are far from the main grid. The microgrid gets popularity because DC power sources such as photovoltaics (PVs), battery banks, and fuel cells can be interconnected without AC/DC converters. The stochastic nature of PV...

  7. Active superconducting DC fault current limiter based on flux compensation

    Shi Jing; Tang Yuejin; Wang, Chen; Zhou Yusheng; Li Jingdong; Ren Li; Chen Shijie

    2006-01-01

    With the extensive application of DC power systems, suppression of DC fault current is an important subject that guarantees system security. This paper presents an active superconducting DC fault current limiter (DC-SFCL) based on flux compensation. The DC-SFCL is composed of two superconducting windings wound on a single iron core, the primary winding is in series with DC power system, and the second winding is connected with AC power system through a PWM converter. In normal operating state, the flux in the iron core is compensated to zero, and the SFCL has no influence on DC power system. In the case of DC system accident, through regulating the active power exchange between the SFCL's second winding and the AC power system, the current on the DC side can be limited to different level complying with the system demand. Moreover, the PWM converter that interface the DC system and AC system can be controlled as a reactive power source to supply voltage support for the AC side, which has little influence on the performance of SFCL. Using MATLAB SIMULINK, the mathematic model of the DC-SFCL is created, simulation results validate the dynamics of system, and the performance of DC-SFCL is confirmed

  8. Overvoltage protection in DC power systems; Ueberspannungsschutz in Gleichstromanlagen

    Birkl, Josef; Zahlmann, Peter [Dehn + Soehne GmbH + Co.KG, Neumarkt (Germany)

    2012-02-15

    The utilisation of DC power systems has increased dramatically in the recent years. In addition to traditional DC applications such as in telecommunications and railway engineering a variety of DC applications arise due to a rapid spread of photovoltaic systems. Current projects for the e-mobility expand the scope of application.

  9. On the modelling of linear-assisted DC-DC voltage regulators for photovoltaic solar energy systems

    Martínez-García, Herminio; García-Vílchez, Encarna

    2017-11-01

    This paper shows the modelling of linear-assisted or hybrid (linear & switching) DC/DC voltage regulators. In this kind of regulators, an auxiliary linear regulator is used, which objective is to cancel the ripple at the output voltage and provide fast responses for load variations. On the other hand, a switching DC/DC converter, connected in parallel with the linear regulator, allows to supply almost the whole output current demanded by the load. The objective of this topology is to take advantage of the suitable regulation characteristics that series linear voltage regulators have, but almost achieving the high efficiency that switching DC/DC converters provide. Linear-assisted DC/DC regulators are feedback systems with potential instability. Therefore, their modelling is mandatory in order to obtain design guidelines and assure stability of the implemented power supply system.

  10. First Implementation of a Two-Stage DC-DC Conversion Powering Scheme for the CMS Phase-2 Outer Tracker

    Feld, Lutz Werner; Karpinski, Waclaw; Klein, Katja; Lipinski, Martin; Pauls, Alexander Josef; Preuten, Marius; Rauch, Max Philip; Wangelik, Frederik; Wlochal, Michael

    2017-01-01

    The 2S silicon strip modules for the CMS Phase-2 tracker upgrade will require two operating voltages. These will be provided via a two-step DC-DC conversion powering scheme, in which one DC-DC converter delivers 2.5\\,V while the second DC-DC converter receives 2.5\\,V at its input and converts it to 1.2\\,V. The DC-DC converters will be mounted on a flex PCB, the service hybrid, together with an opto-electrical converter module (VTRx+) and a serializer (LP-GBT). The service hybrid will be mounted directly on the 2S module. A prototype service hybrid has been developed and its performance has been evaluated, including radiative and conductive noise emissions, and efficiency. In addition system tests with a prototype module have been performed. In this report the service hybrid will be described and the test results will be summarized.

  11. All Digital Switch-Mode DC/DC Converters with BIST Functionality for Harsh Space Environments, Phase I

    National Aeronautics and Space Administration — The Space Micro Arizona State University (ASU) team will develop an all-digitally controlled, wide temperature range point-of-load switch-mode DC-DC regulator core...

  12. DC-Voltage Fluctuation Elimination Through a DC-Capacitor Current Control for DFIG Converters Under Unbalanced Grid Voltage Conditions

    Liu, Changjin; Xu, Dehong; Zhu, Nan

    2013-01-01

    Unbalanced grid voltage causes a large second-order harmonic current in the dc-link capacitors as well as dc-voltage fluctuation, which potentially will degrade the lifespan and reliability of the capacitors in voltage source converters. This paper proposes a novel dc-capacitor current control...... method for a grid-side converter (GSC) to eliminate the negative impact of unbalanced grid voltage on the dc-capacitors. In this method, a dc-capacitor current control loop, where a negative-sequence resonant controller is used to increase the loop gain, is added to the conventional GSC current control...... loop. The rejection capability to the unbalanced grid voltage and the stability of the proposed control system are discussed. The second-order harmonic current in the dc capacitor as well as dc-voltage fluctuation is very well eliminated. Hence, the dc capacitors will be more reliable under unbalanced...

  13. Next-Generation Shipboard DC Power System

    Jin, Zheming; Sulligoi, Giorgio; Cuzner, Rob

    2016-01-01

    sources (RES) are commonly recognized as the major driven force of the revolution, the outburst of customer electronics and new kinds of household electronics is also powering this change. In this context, dc power distribution technologies have made a comeback and keep gaining a commendable increase...... in research interests and industrial applications. In addition, the concept of flexible and smart distribution has also been proposed, which tends to exploit distributed generation and pack the distributed RESs and local electrical loads as an independent and self-sustainable entity, namely microgrid....... At present, the research of dc microgrid has investigated and developed a series of advanced methods in control, management and objective-oriented optimization, which would found the technical interface enabling the future applications in multiple industrial areas, such as smart buildings, electric vehicles...

  14. Artificial noise due to DC electric trains

    Senanayake, W.E.

    1987-08-01

    The current distribution in a DC railway and the resulting magnetic effects have been modelled using the parameters of the DC railway networks in Italy. The results show that the magnetic perturbations are substantially high in the vicinity of electrified railway lines. The order of magnitude of the induced field can be as significant as ∼ 40nT at a distance of ≅ 2km from the railway line indicating that geophysical techniques that employ natural magnetic anomalies can be badly effected, within this range. The magnetic effects rapidly decay with increasing distance, but the noise level could be significant even at a range of ∼ 10km. Also, these induced anomalies vary significantly with the conductivity of the ground. When the conductivity is high it is possible that the railway currents dispersed through the ground interact with those induced in the earth, causing a severe disruption to the telluric measurements. (author). 11 refs, 10 figs, 1 tab

  15. Macroscopic quantum tunneling in a dc SQUID

    Chen, Y.C.

    1986-01-01

    The theory of macroscopic quantum tunneling is applied to a current-biased dc SQUID whose dynamics can be described by a two-dimensional mechanical system with a dissipative environment. Based on the phenomenological model proposed by Caldeira and Leggett, the dissipative environment is represented by a set of harmonic oscillators coupling to the system. After integrating out the environmental degrees of freedom, an effective Euclidean action is found for the two-dimensional system. The action is used to provide the quantum tunneling rate formalism for the dc SQUID. Under certain conditions, the tunneling rate reduces to that of a single current-biased Josephson junction with an adjustable effective critical current

  16. Universality of DC electrical conductivity from holography

    Ge, Xian-Hui, E-mail: gexh@shu.edu.cn [Shanghai Key Laboratory of High Temperature Superconductors, Department of Physics, Shanghai University, Shanghai, 200444 (China); Department of Physics, University of California, San Diego, CA92122 (United States); Sin, Sang-Jin, E-mail: sjsin@hangyang.ac.kr [Department of Physics, Hanyang University, Seoul 133-791 (Korea, Republic of); Wu, Shao-Feng, E-mail: sfwu@shu.edu.cn [Department of Physics, Shanghai University, Shanghai, 200444 (China)

    2017-04-10

    We propose a universal formula of dc electrical conductivity in rotational- and translational-symmetries breaking systems via the holographic duality. This formula states that the ratio of the determinant of the dc electrical conductivities along any spatial directions to the black hole area density in zero-charge limit has a universal value. As explicit illustrations, we give several examples elucidating the validation of this formula: We construct an anisotropic black brane solution, which yields linear in temperature for the in-plane resistivity and insulating behavior for the out-of-plane resistivity; We also construct a spatially isotropic black brane solution that both the linear-T and quadratic-T contributions to the resistivity can be realized.

  17. A comprehensive analysis and hardware implementation of control strategies for high output voltage DC-DC boost power converter

    Padmanaban, Sanjeevikumar; Grandi, Gabriele; Blaabjerg, Frede; Wheeler, Patrick; Siano, Pierluigi; Hammami, Manel

    2017-01-01

    Classical DC-DC converters used in high voltage direct current (HVDC) power transmission systems, lack in terms of efficiency, reduced transfer gain and increased cost with sensor (voltage/current) numbers. Besides, the internal self-parasitic behavior of the power components reduces the output voltage and efficiency of classical HV converters. This paper deals with extra high-voltage (EHV) dc-dc boost converter by the application of voltage-lift technique to overcome the aforementioned defic...

  18. Power Oscillations Damping in DC Microgrids

    Hamzeh, Mohsen; Ghafouri, Mohsen; Karimi, Houshang

    2016-01-01

    This paper proposes a new control strategy for damping of power oscillations in a multi-source dc microgrid. A parallel combination of a fuel cell (FC), a photovoltaic (PV) system and a supercapacitor (SC) are used as a hybrid power conversion system (HPCS). The SC compensates for the slow transi...... of the proposed control scheme is verified using hardware-in-the-loop (HIL) simulations carried out in OPAL-RT technologies....

  19. Circuit Regulates Speed Of dc Motor

    Weaver, Charles; Padden, Robin; Brown, Floyd A., Jr.

    1990-01-01

    Driving circuit regulates speed of small dc permanent-magnet motor in tape recorder. Two nested feedback loops maintain speed within 1 percent of constant value. Inner loop provides coarse regulation, while outer loop removes most of variation in speed that remains in the presence of regulation by the inner loop. Compares speed of motor with commanded speed and adjusts current supplied to motor accordingly.

  20. DC Characterization of Different Advanced MOSFET Architectures

    Jomaah, J.; Fadlallah, M.; Ghibaudo, G.

    2011-01-01

    A review of recent results concerning the DC characterization of FD- and Double Gate SOI MOSFET's and FinFETs in modern CMOS technologies is given. By proper extraction techniques, distinction between the different interaction mechanisms is done. Parameter extraction conducted at room and low temperature clearly indicates that the mobility is directly impacted by shrinking the gate length in sub 100nm architectures. (author)

  1. Development of a smart DC grid model

    Dalimunthe, Amty Ma’rufah Ardhiyah; Mindara, Jajat Yuda; Panatarani, Camellia; Joni, I. Made, E-mail: imadejoni@phys.unpad.ac.id [Lab. of Instrumentation System and Functional Material Processing, Physics Department, Faculty of Mathematics and Natural Sciences, Padjadjaran University, Jl. Raya Bandung-Sumedang KM21, Jatinangor 45363, Jawa Barat (Indonesia)

    2016-03-11

    Smart grid and distributed generation should be the solution of the global climate change and the crisis energy of the main source of electrical power generation which is fossil fuel. In order to meet the rising electrical power demand and increasing service quality demands, as well as reduce pollution, the existing power grid infrastructure should be developed into a smart grid and distributed power generation which provide a great opportunity to address issues related to energy efficiency, energy security, power quality and aging infrastructure systems. The conventional of the existing distributed generation system is an AC grid while for a renewable resources requires a DC grid system. This paper explores the model of smart DC grid by introducing a model of smart DC grid with the stable power generation give a minimal and compressed circuitry that can be implemented very cost-effectively with simple components. The PC based application software for controlling was developed to show the condition of the grid and to control the grid become ‘smart’. The model is then subjected to a severe system perturbation, such as incremental change in loads to test the performance of the system again stability. It is concluded that the system able to detect and controlled the voltage stability which indicating the ability of power system to maintain steady voltage within permissible rangers in normal condition.

  2. Development of a smart DC grid model

    Dalimunthe, Amty Ma’rufah Ardhiyah; Mindara, Jajat Yuda; Panatarani, Camellia; Joni, I. Made

    2016-01-01

    Smart grid and distributed generation should be the solution of the global climate change and the crisis energy of the main source of electrical power generation which is fossil fuel. In order to meet the rising electrical power demand and increasing service quality demands, as well as reduce pollution, the existing power grid infrastructure should be developed into a smart grid and distributed power generation which provide a great opportunity to address issues related to energy efficiency, energy security, power quality and aging infrastructure systems. The conventional of the existing distributed generation system is an AC grid while for a renewable resources requires a DC grid system. This paper explores the model of smart DC grid by introducing a model of smart DC grid with the stable power generation give a minimal and compressed circuitry that can be implemented very cost-effectively with simple components. The PC based application software for controlling was developed to show the condition of the grid and to control the grid become ‘smart’. The model is then subjected to a severe system perturbation, such as incremental change in loads to test the performance of the system again stability. It is concluded that the system able to detect and controlled the voltage stability which indicating the ability of power system to maintain steady voltage within permissible rangers in normal condition.

  3. Frequency analysis of DC tolerant current transformers

    Mlejnek, P; Kaspar, P

    2013-01-01

    This article deals with wide frequency range behaviour of DC tolerant current transformers that are usually used in modern static energy meters. In this application current transformers must comply with European and International Standards in their accuracy and DC tolerance. Therefore, the linear DC tolerant current transformers and double core current transformers are used in this field. More details about the problems of these particular types of transformers can be found in our previous works. Although these transformers are designed mainly for power distribution network frequency (50/60 Hz), it can be interesting to understand their behaviour in wider frequency range. Based on this knowledge the new generations of energy meters with measuring quality of electric energy will be produced. This solution brings better measurement of consumption of nonlinear loads or measurement of non-sinusoidal voltage and current sources such as solar cells or fuel cells. The determination of actual power consumption in such energy meters is done using particular harmonics component of current and voltage. We measured the phase and ratio errors that are the most important parameters of current transformers, to characterize several samples of current transformers of both types

  4. Ac-dc converter firing error detection

    Gould, O.L.

    1996-01-01

    Each of the twelve Booster Main Magnet Power Supply modules consist of two three-phase, full-wave rectifier bridges in series to provide a 560 VDC maximum output. The harmonic contents of the twelve-pulse ac-dc converter output are multiples of the 60 Hz ac power input, with a predominant 720 Hz signal greater than 14 dB in magnitude above the closest harmonic components at maximum output. The 720 Hz harmonic is typically greater than 20 dB below the 500 VDC output signal under normal operation. Extracting specific harmonics from the rectifier output signal of a 6, 12, or 24 pulse ac-dc converter allows the detection of SCR firing angle errors or complete misfires. A bandpass filter provides the input signal to a frequency-to-voltage converter. Comparing the output of the frequency-to-voltage converter to a reference voltage level provides an indication of the magnitude of the harmonics in the ac-dc converter output signal

  5. Marvel and DC Characters Inspired by Arachnids

    Elidiomar Ribeiro Da-Silva

    2014-12-01

    Full Text Available This article compares arachnid-based Marvel and DC comics characters. The composition of a comic book character often has interesting ‘real-life’ influences. Given the strong connection between arachnids (especially spiders, scorpions and mites, all belonging to the zoological class 'Arachnida' and human beings it is not surprising that they have inspired many fictional characters. We recorded 84 Marvel Comics characters and 40 DC Comics characters, detailed in the dataset that accompanies the article (Da-Silva 2014. Most characters have been created recently, since the 1990s. Marvel has significantly more arachnid characters than DC. As for taxonomic classification, the characters were based mostly on spiders (zoological order 'Araneae'. Of the total characters, the majority are human beings, but an overwhelming number have at least some typical arachnid features. Villains (60.91% of total are significantly more numerous, considering the sum of the two publishers. Arachnids have bad reputation for being dangerous (Thorp and Woodson 1976; Ruppert and Barnes 1996. Since the public usually considers spiders, scorpions and mites “harmful” in general, we expected a larger contingent of villains. However, there was no statistical difference between the amount of villains and heroes in Marvel characters. It did not happen probably due to the success of one character: the Amazing Spider-Man.

  6. Performance of 22.4-kW nonlaminated-frame dc series motor with chopper controller. [a dc to dc voltage converter

    Schwab, J. R.

    1979-01-01

    Performance data obtained through experimental testing of a 22.4 kW traction motor using two types of excitation are presented. Ripple free dc from a motor-generator set for baseline data and pulse width modulated dc as supplied by a battery pack and chopper controller were used for excitation. For the same average values of input voltage and current, the motor power output was independent of the type of excitation. However, at the same speeds, the motor efficiency at low power output (corresponding to low duty cycle of the controller) was 5 to 10 percentage points lower on chopped dc than on ripple free dc. The chopped dc locked-rotor torque was approximately 1 to 3 percent greater than the ripple free dc torque for the same average current.

  7. Digital DC beam current measurement on SSRF storage ring

    Xiong Liang; Yin Chongxian; Liu Ming; Chen Jianfeng

    2011-01-01

    Both DC current transformer (DCCT) and integrating current transformer (ICT) can be used in DC beam current measurement. The ICT has strong capability of resisting electromagnetic interference, but its measurement accuracy cannot satisfy the DC beam current measurement requirement when using traditional high speed A/D. With high resolution A/D and equivalent sampling system, DC beam current measuring system based on ICT can reach high accuracy compared with DCCT system. In this paper, the ICT-based DC beam current measurement, equivalent sampling method and testing results at Shanghai Synchrotron Radiation Facility(SSRF) is described. (authors)

  8. Controlling DC permeability in cast steels

    Sumner, Aaran; Gerada, Chris; Brown, Neil; Clare, Adam

    2017-01-01

    Annealing (at multiple cooling rates) and quenching (with tempering) was performed on specimens of cast steel of varying composition. The aim was to devise a method for selecting the steel with the highest permeability, from any given range of steels, and then increasing the permeability by heat treatment. Metallographic samples were imaged using optical microscopy to show the effect of the applied heat treatments on the microstructure. Commonly cast steels can have DC permeability altered by the careful selection of a heat treatment. Increases of up to 381% were achieved by annealing using a cooling rate of 6.0 °C/min. Annealing was found to cause the carbon present in the steel to migrate from grain boundaries and from within ferrite crystals into adjacent pearlite crystals. The migration of the carbon resulted in less carbon at grain boundaries and within ferrite crystals reducing the number of pinning sites between magnetic domains. This gives rise to a higher permeability. Quenching then tempering was found to cause the formation of small ferrite crystals with the carbon content of the steel predominately held in the martensitic crystal structures. The results show that with any given range of steel compositions the highest baseline DC permeability will be found with the steel that has the highest iron content and the lowest carbon content. For the samples tested in this paper a cooling rate of 4.5 °C/min resulted in the relative permeability of the sample with the highest baseline permeability, AS4, increasing from 783 to 1479 at 0.5 T. This paper shows how heat treatments commonly applied to hypoeutectoid cast steels, to improve their mechanical performance, can be used to also enhance electromagnetic properties of these alloys. The use of cast steels allows the creation of DC components for electrical machines not possible by the widely used method of stacking of electrical grade sheet steels. - Highlights: • A range of structural steels had their

  9. Controlling DC permeability in cast steels

    Sumner, Aaran, E-mail: aaran.sumner@nottingham.ac.uk [University of Nottingham, Nottingham University Park Campus, Nottingham NG7 2RD, England (United Kingdom); Gerada, Chris, E-mail: chris.gerada@nottingham.ac.uk [Electrical Machines, University of Nottingham, Tower Building, Nottingham NG7 2RD, England (United Kingdom); Brown, Neil, E-mail: neil.brown@cummins.com [Advanced Electrical Machines Research and Technology at Cummins Power Generation, Peterborough PE2 6FZ, England (United Kingdom); Clare, Adam, E-mail: adam.clare@nottingham.ac.uk [Advanced Manufacturing, University of Nottingham, University Park Campus, Nottingham NG7 2RD, England (United Kingdom)

    2017-05-01

    Annealing (at multiple cooling rates) and quenching (with tempering) was performed on specimens of cast steel of varying composition. The aim was to devise a method for selecting the steel with the highest permeability, from any given range of steels, and then increasing the permeability by heat treatment. Metallographic samples were imaged using optical microscopy to show the effect of the applied heat treatments on the microstructure. Commonly cast steels can have DC permeability altered by the careful selection of a heat treatment. Increases of up to 381% were achieved by annealing using a cooling rate of 6.0 °C/min. Annealing was found to cause the carbon present in the steel to migrate from grain boundaries and from within ferrite crystals into adjacent pearlite crystals. The migration of the carbon resulted in less carbon at grain boundaries and within ferrite crystals reducing the number of pinning sites between magnetic domains. This gives rise to a higher permeability. Quenching then tempering was found to cause the formation of small ferrite crystals with the carbon content of the steel predominately held in the martensitic crystal structures. The results show that with any given range of steel compositions the highest baseline DC permeability will be found with the steel that has the highest iron content and the lowest carbon content. For the samples tested in this paper a cooling rate of 4.5 °C/min resulted in the relative permeability of the sample with the highest baseline permeability, AS4, increasing from 783 to 1479 at 0.5 T. This paper shows how heat treatments commonly applied to hypoeutectoid cast steels, to improve their mechanical performance, can be used to also enhance electromagnetic properties of these alloys. The use of cast steels allows the creation of DC components for electrical machines not possible by the widely used method of stacking of electrical grade sheet steels. - Highlights: • A range of structural steels had their

  10. Series-Connected High Frequency Converters in a DC Microgrid System for DC Light Rail Transit

    Bor-Ren Lin

    2018-01-01

    Full Text Available This paper studies and presents a series-connected high frequency DC/DC converter connected to a DC microgrid system to provide auxiliary power for lighting, control and communication in a DC light rail vehicle. Three converters with low voltage and current stresses of power devices are series-connected with single transformers to convert a high voltage input to a low voltage output for a DC light rail vehicle. Thus, Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs with a low voltage rating and a turn-on resistance are adopted in the proposed circuit topology in order to decrease power losses on power switches and copper losses on transformer windings. A duty cycle control with an asymmetric pulse-width modulation is adopted to control the output voltage at the desired voltage level. It is also adopted to reduce switching losses on MOSFETs due to the resonant behavior from a leakage inductor of an isolated transformer and output capacitor of MOSFETs at the turn-on instant. The feasibility and effectiveness of the proposed circuit have been verified by a laboratory prototype with a 760 V input and a 24 V/60 A output.

  11. RF-superimposed DC and pulsed DC sputtering for deposition of transparent conductive oxides

    Stowell, Michael; Mueller, Joachim; Ruske, Manfred; Lutz, Mark; Linz, Thomas

    2007-01-01

    Transparent conductive oxide films are widely used materials for electronic applications such as flat panel displays and solar cells. The superposition of DC and pulsed DC power by a certain fraction of RF power was applied to deposit indium tin oxide films. This technique allows an additional tuning of different parameters relevant to film growth, and yields high quality films even under kinetically limited conditions. A long-term stable RF/DC process could be realized by using different combinations of standard power supply components, which includes a fully reliable arc handling system for both the RF and DC generators. The effectiveness of the arc handling system is illustrated by the current and voltage behavior recorded for actual arcing events. The resistivity of indium tin oxide films is strongly influenced by the respective sputtering mode. The best resistivity values of 145-148 μΩ cm were obtained by RF-superimposed pulsed DC sputtering at a pulse frequency between 100 and 200 kHz and a substrate temperature as low as 140 deg. C. In addition, the films were extremely smooth with a surface roughness of 1-2.5 nm

  12. Guest Editorial Special Issue on Structured DC Microgrids

    Guerrero, Josep M.; Tan, Don F. D.

    2017-01-01

    With the development of dc coupled devices, such as photovoltaic generations, batteries, supercapacitors, LEDs, computers, and electronics equipment, low-voltage dc distribution networks, structured dc microgrids are emerging as a natural platform to integrate renewable energy sources. However...... in either series/parallel, forming a number of dc busses with different voltage levels. Recently, with the advance of new dc power technologies, several ongoing standards, alliances, and initiatives are bringing the possibility of developing future homes, offices, buildings, campuses, datacenters, ships......, satellites, aircrafts, and other electrical power systems to operate totally or dominantly in dc. Research is being carried out in both the system and component levels of modeling, control, and stability of structured dc microgrids. New high-efficiency topologies and protections are also key nontrivial...

  13. A Decentralized Current-Sharing Controller Endows Fast Transient Response to Parallel DC-DC Converters

    Wang, Haojie; Han, Minxiao; Han, Renke

    2018-01-01

    This paper proposes a decentralized current-sharing control strategy to endow fast transient response to paralleled DC-DC converters systems, such as DC microgrids or distributed power systems. The proposed controller consist of two main control loops: an external voltage droop control for current......-sharing proposes and an internal current loop. The external droop control loop is designed as a voltage loop with embedded virtual impedance, which avoids the use of a slow voltage loop and a separate extra virtual impedance loop that may limit the system bandwidth. The internal current loop, thanks...... and the proposed embedded-virtual-impedance based I-V droop. In order to compare the dynamic response performances between two droop controllers, their state-space models have been developed and analyzed in this paper. The results show that the dynamic response of the I-V droop control is faster than...

  14. Integrating DC/DC Conversion with Possible Reconfiguration within Submodule Solar Photovoltaic Systems

    Huang, Peter Jen-Hung

    This research first proposes a method to merge photovoltaic (PV) cells or PV panels within the internal components DC-DC converters. The purpose of this merged structure is to reconfigure the PV modules between series and parallel connections using high switching frequencies (hundreds of kHz). This leads to multi-levels of voltages and currents that become applied to the output filter of the converter. Further, this research introduces a concept of a switching cell that utilizes the reconfiguration of series and parallel connections in DC-DC converters. The switching occurs at high switching frequency and the switches can be integrated to be within the solar panels or in between the solar cells. The concept is generalized and applied to basic buck and boost topologies. As examples of the new types of converters: reconfigurable PV-buck and PV-boost converter topologies are presented. It is also possible to create other reconfigurable power converters: non-isolated and isolated topologies. Analysis, simulation and experimental verification for the reconfigurable PV-buck and PV-boost converters are presented extensively to illustrate proof of concept. Benefits and drawbacks of the new approach are discussed. The second part of this research proposes to utilize the internal solar cell capacitance and internal solar module wire parasitic inductances to replace the input capacitor and filter inductor in boost derived DC-DC converters for energy harvesting applications. High switching frequency (MHz) hard switched and resonant boost converters are proposed. Their analysis, simulation and experimental prototypes are presented. A specific proof-of-concept application is especially tested for foldable PV panels, which are known for their high internal wire inductance. The experimental converters successfully boost solar module voltage without adding any external input capacitance or filter inductor. Benefits and drawbacks of new proposed PV submodule integrated boost

  15. Efficient Visible Light Communication Transmitters Based on Switching-Mode dc-dc Converters

    2018-01-01

    Visible light communication (VLC) based on solid-state lighting (SSL) is a promising option either to supplement or to substitute existing radio frequency (RF) wireless communication in indoor environments. VLC systems take advantage of the fast modulation of the visible light that light emitting diodes (LEDs) enable. The switching-mode dc-to-dc converter (SMCdc-dc) must be the cornerstone of the LED driver of VLC transmitters in order to incorporate the communication functionality into LED lighting, keeping high power efficiency. However, the new requirements related to the communication, especially the high bandwidth that the LED driver must achieve, converts the design of the SMCdc-dc into a very challenging task. In this work, three different methods for achieving such a high bandwidth with an SMCdc-dc are presented: increasing the order of the SMCdc-dc output filter, increasing the number of voltage inputs, and increasing the number of phases. These three strategies are combinable and the optimum design depends on the particular VLC application, which determines the requirements of the VLC transmitter. As an example, an experimental VLC transmitter based on a two-phase buck converter with a fourth-order output filter will demonstrate that a bandwidth of several hundred kilohertz (kHz) can be achieved with output power levels close to 10 W and power efficiencies between 85% and 90%. In conclusion, the design strategy presented allows us to incorporate VLC into SSL, achieving high bit rates without damaging the power efficiency of LED lighting. PMID:29642455

  16. A Novel Quasi-SEPIC High-Voltage Boost DC-DC Converter

    Siwakoti, Yam Prasad; N. Soltani, Mohsen; Blaabjerg, Frede

    2017-01-01

    This paper proposes a modified coupled-inductor SEPIC dc-dc converter for low power and high voltage gain applications such as for piezoelectric drive systems. The converter uses the same components as of SEPIC converter with an additional diode. Compared to conventional topologies with similar...... voltage gain expression, the proposed topology uses less components to achieve same or even higher voltage gain. This helps to design a very compact and light weight converter with higher power density at lower cost. Due to brevity, the principle of operation, theoretical analysis and comparison supported...

  17. A high voltage gain quasi Z-source isolated DC/DC converter

    Siwakoti, Yam P.; Blaabjerg, Frede; Loh, Poh Chiang

    2014-01-01

    A compact quasi-Z-source DC/DC converter is presented with high voltage gain, isolated output, and improved efficiency. The improvements in size and performance were achieved by using a square wave inverter with only two output switches driving an isolating transformer in push-pull mode, followed...... by a voltage doubling output rectifier. The converter is well-suited to applications requiring a high voltage gain, especially renewable energy sources such as photovoltaic and fuel-cell power supplies. To demonstrate the converter's performance a prototype designed to output 400 V at 500 W was constructed...

  18. Ultra-Step-Up DC-DC Converter with Integrated Autotransformer and Coupled Inductor

    Siwakoti, Yam Prasad; Blaabjerg, Frede; Loh, Poh Chiang

    2016-01-01

    This paper introduces a new single-switch nonisolated dc-dc converter with very high voltage transfer ratio and reduced semiconductor voltage stress. The converter utilizes an integrated autotransformer and a coupled inductor on the same core to achieve a high step-up voltage gain without extreme...... duty cycle. Further, an integrated passive regenerative circuit recycles the leakage energy of the coupled magnetics and transfer the leakage energy to the load, which helps to avoid high voltage spikes across the switch. This feature along with low stress on the switching device enables the designer...

  19. Modified High Voltage Conversion Inverting Cuk DC-DC Converter for Renewable Energy Application

    Maroti, Pandav Kiran; Padmanaban, Sanjeevikumar; Wheeler, Patrick

    2017-01-01

    controlled device DC-DC topology. The voltage conversion ratio of proposed converter has increased by ten times of the conventional Cuk converterat a duty ratio of 90%. The detailed analysis of the voltage conversion ratio and losses occur due to internal resistance of components is done in the paper......The proposed exertion represents the modified high voltage conversion Cuk converter for renewable energy application. The proposed Cuk converter is a combination of the conventional boost converter and Cuk converter. The arrangement of the proposed converter make, such as, it becomes the single...

  20. High-Efficiency Photovoltaic System Using Partially-Connected DC-DC Converter

    Uno, Masatoshi; Kukita, Akio; Tanaka, Koji

    Power conversion electronics for photovoltaic (PV) systems are desired to operate as efficiently as possible to exploit the power generated by PV modules. This paper proposes a novel PV system in which a dc-dc converter is partially connected to series-connected PV modules. The proposed system achieves high power-conversion efficiency by reducing the passing power and input/output voltages of the converter. The theoretical operating principle was experimentally validated. Resultant efficiency performances of the proposed and conventional systems demonstrated that the proposed system was more efficient in terms of power conversion though the identical converter was used for the both systems.

  1. Four Quadrants Integrated Transformers for Dual-input Isolated DC-DC Converters

    Ouyang, Ziwei; Zhang, Zhe; Andersen, Michael A. E.

    2012-01-01

    A common limitation of power coupling effect in some known multiple-input dc-dc converters has been addressed in many literatures. In order to overcome this limitation, a new concept for decoupling the primary windings in the integrated multiple-winding transformers based on 3-dimensional (3D...... perpendicular primary windings, a name of “four quadrants integrated transformers” (FQIT) is therefore given to the proposed construction. Since the two primary windings are uncoupled, the FQIT allows the two input power stages to transfer the energy into the output load simultaneously or at any...

  2. State-plane analysis of zero-voltage-switching resonant dc/dc power converters

    Kazimierczuk, Marian K.; Morse, William D.

    The state-plane analysis technique for the zero-voltage-switching resonant dc/dc power converter family of topologies, namely the buck, boost, buck-boost, and Cuk converters is established. The state plane provides a compression of information that allows the designer to uniquely examine the nonlinear dynamics of resonant converter operation. Utilizing the state plane, resonant converter modes of operation are examined and the switching frequencies are derived for the boundaries between these modes, including the boundary of energy conversion.

  3. DC-DC Converter Topology Assessment for Large Scale Distributed Photovoltaic Plant Architectures

    Agamy, Mohammed S; Harfman-Todorovic, Maja; Elasser, Ahmed; Sabate, Juan A; Steigerwald, Robert L; Jiang, Yan; Essakiappan, Somasundaram

    2011-07-01

    Distributed photovoltaic (PV) plant architectures are emerging as a replacement for the classical central inverter based systems. However, power converters of smaller ratings may have a negative impact on system efficiency, reliability and cost. Therefore, it is necessary to design converters with very high efficiency and simpler topologies in order not to offset the benefits gained by using distributed PV systems. In this paper an evaluation of the selection criteria for dc-dc converters for distributed PV systems is performed; this evaluation includes efficiency, simplicity of design, reliability and cost. Based on this evaluation, recommendations can be made as to which class of converters is best fit for this application.

  4. GaN-based High Efficiency Bidirectional DC-DC Converter with 10 MHz Switching Frequency

    Kruse, Kristian; Zhang, Zhe; Elbo, Mads

    2017-01-01

    -isolated bidirectional DC-DC converter equipped with Gallium Nitride (GaN) semiconductor transistors is presented. The converter’s operation principles, zero-voltage switching (ZVS) constraints and dead-time effects are studied. Moreover, the optimization and tradeoffs on the adopted high-frequency inductor...... are achieved. Moreover, the measured losses can match the theoretically calculated counterparts well, therefore the design and analysis are verified. However, from the experimental test carried out, it can also be seen, that making a compact converter, even for a GaN-based one, operate at 10 MHz and 100 W...

  5. Deadbeat control of power leveling unit with bidirectional buck/boost DC/DC converter

    Hamasaki, Shin-ichi; Mukai, Ryosuke; Yano, Yoshihiro; Tsuji, Mineo

    2014-01-01

    As a distributed generation system increases, a stable power supply becomes difficult. Thus control of power leveling (PL) unit is required to maintain the balance of power flow for irregular power generation. The unit is required to respond to change of voltage and bidirectional power flow. So the bidirectional buck/boost DC/DC converter is applied for the control of PL unit in this research. The PL unit with Electric double-layer capacitor (EDLC) is able to absorb change of power, and it is...

  6. Comparison of two different high performance mixed signal controllers for DC/DC converters

    Jakobsen, Lars Tønnes; Andersen, Michael Andreas E.

    2006-01-01

    This paper describes how mixed signal controllers combining a cheap microcontroller with a simple analogue circuit can offer high performance digital control for DC/DC converters. Mixed signal controllers have the same versatility and performance as DSP based controllers. It is important to have...... an engineer experienced in microcontroller programming write the software algorithms to achieve optimal performance. Two mixed signal controller designs based on the same 8-bit microcontroller are compared both theoretically and experimentally. A 16-bit PID compensator with a sampling frequency of 200 k......Hz implemented in the 16 MIPS, 8-bit ATTiny26 microcontroller is demonstrated....

  7. Very High Frequency Resonant DC/DC Converters for LED Lighting

    Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

    2013-01-01

    This paper presents a very high frequency DC/DC converter for LED lighting. Several resonant topologies are compared and their usability discussed. At the end the resonant SEPIC converter is chosen based on the achievable power density and total bill of material. Simulations of a 51 MHz converter...... with 40 V input and 15 V output are made. The simulation shows possibility of achieving efficiency up to 87 % even with a HEXFET Power MOSFET. Three prototypes of the simulated converter are implemented showing good correlation with simulations. The prototypes have efficiencies up to 84 % and power...

  8. State trajectories used to observe and control dc-to-dc converters

    Burns, W. W., III; Wilson, T. G.

    1976-01-01

    State-plane analysis techniques are employed to study the voltage stepup energy-storage dc-to-dc converter. Within this framework, an example converter operating under the influence of a constant on-time and a constant frequency controller is examined. Qualitative insight gained through this approach is used to develop a conceptual free-running control law for the voltage stepup converter which can achieve steady-state operation in one on/off cycle of control. Digital computer simulation data are presented to illustrate and verify the theoretical discussions presented.

  9. 75 FR 47199 - Airworthiness Directives; McDonnell Douglas Corporation Model DC-9-10 Series Airplanes, DC-9-30...

    2010-08-05

    ... Airworthiness Directives; McDonnell Douglas Corporation Model DC- 9-10 Series Airplanes, DC-9-30 Series... existing airworthiness directive (AD), which applies to all McDonnell Douglas Model DC-9-10 series..., 2010). That AD applies to all McDonnell Douglas Corporation Model DC-9-10 series airplanes, DC-9-30...

  10. Feasibility analysis of the application and positioning of DC HTS FCL in a DC microgrid through modeling and simulation using Simulink and SimPowerSystem

    Khan, U.A.; Shin, W.J.; Seong, J.K.; Oh, S.H.; Lee, S.H.; Lee, B.W.

    2011-01-01

    We modeled DC SFCL by use of SimPowerSystem blocks. We examine the DC fault current limitation in low voltage DC distribution networks. SFCL's affects at critical points were measured. SFCL installed at the substation rectifier branch resulted in abnormal increase of fault current. The strategic location of SFCL is the point of integration of the PV plant with the power grid. DC fault current limitation in DC distribution network is one of the critical issues which need to be taken care of before they can be practically implemented. High temperature superconductors could be efficiently installed to cope with the problem of DC fault currents. In this paper, a generalized DC high temperature superconducting fault current limiter (SFCL) is modeled by integrating Simulink and SimPowerSystem blocks. This model is designed for limiting DC fault currents in low voltage DC distribution networks. A DC microgrid having a low voltage DC distribution network, an integrated photovoltaic plant and domestic customer load is modeled. Transient analysis of the DC microgrid is performed by generating fault and measuring DC fault currents at critical points. The designed DC SFCL is placed at different strategic locations in DC microgrid and fault current limitation performance of DC SFCL in DC microgrid has been analyzed. Moreover, the affects of rapid impedance changing in the distribution network due to the fault followed by DC SFCL activation is investigated. Finally, the best suitable position and affects of DC SFCL in a DC microgrid along with suggestions for implementation have been proposed.

  11. Improved DC Gun and Insulator Assembly

    Neubauer, Michael [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2015-01-11

    Many user facilities such as synchrotron radiation light sources and free electron lasers rely on DC high voltage photoguns with internal field gradients as high as 10 to 15 MV/m. These high gradients often lead to field emission which poses serious problems for the photocathode used to generate the electron beam and the ceramic insulators used to bias the photocathode at high voltage. Ceramic insulators are difficult to manufacture, require long commissioning times, and have poor reliability, in part because energetic electrons bury themselves in the ceramic causing a buildup of charge and eventual puncture, and also because large diameter ceramics are difficult to braze reliably. The lifetimes of photo cathodes inside high current DC guns exhibiting field emission are limited to less than a hundred hours. Reducing the surface gradients on the metals reduces the field emission, which serves to maintain the required ultrahigh vacuum condition. A novel gun design with gradients around 5 MV/m and operating at 350 kV, a major improvement over existing designs, was proposed that allows for the in-situ replacement of photo cathodes in axially symmetric designs using inverted ceramics. In this project, the existing JLAB CEBAF asymmetric gun design with an inverted ceramic support was modeled and the beam dynamics characterized. An improved structure was designed that reduces the surface gradients and improves the beam optics. To minimize the surface gradients, a number of electrostatic gun designs were studied to determine the optimum configuration of the critical electrodes within the gun structure. Coating experiments were carried out to create a charge dissipative coating for cylindrical ceramics. The phase II proposal, which was not granted, included the design and fabrication of an axially symmetric DC Gun with an inverted ceramic that would operate with less than 5 MV/m at 350 kV and would be designed with an in-situ replaceable photo-cathode.

  12. Protection of AC and DC Microgrids

    Beheshtaein, Siavash; Savaghebi, Mehdi; Quintero, Juan Carlos Vasquez

    2015-01-01

    and DC microgrids, and then investigates the existing and promising solutions for the corresponding challenges. To the authors’ knowledge, three parts of smart grids are required to be developed to facilitate implementation of protection scheme in microgrids. The main requirements and open issues......In future, distributed energy resources (RESs) will be utilized at consumption points. As a consequence, power flow and fault current would be bidirectional and topologydependent; and hence the conventional protection strategies would be inefficient. This paper categorizes the main challenges in AC...

  13. Intelligent Power Control of DC Microgrid

    Hajizadeh, Amin; N. Soltani, Mohsen; Norum, Lars

    2017-01-01

    In this paper, an intelligent power management strategy is proposed for hybrid DC microgrid, including wind turbine, fuel cell and battery energy storage. The considered wind turbine has a permanent magnet synchronous generator (PMSG). In the considered structure, wind turbine operates as the main...... condition and fuel cell will not generate excessive power. The proposed control scheme is based on the fuzzy algorithm. All simulations in variant operational modes are performed by MATLAB/Simulink and results show the effectiveness of the proposed control strategy....

  14. Modelling of dc characteristics for granular semiconductors

    Varpula, Aapo; Sinkkonen, Juha; Novikov, Sergey

    2010-01-01

    The dc characteristics of granular n-type semiconductors are calculated analytically with the drift-diffusion theory. Electronic trapping at the grain boundaries (GBs) is taken into account. The use of quadratic and linear GB potential profiles in the calculation is compared. The analytical model is verified with numerical simulation performed by SILVACO ATLAS. The agreement between the analytical and numerical results is excellent in a large voltage range. The results show that electronic trapping at the GBs has a remarkable effect on the highly nonlinear I-V characteristics of the material.

  15. Modelling of dc characteristics for granular semiconductors

    Varpula, Aapo; Sinkkonen, Juha; Novikov, Sergey, E-mail: aapo.varpula@tkk.f [Department of Micro and Nanosciences, Aalto University, PO Box 13500, FI-00076 Aalto, Espoo (Finland)

    2010-11-01

    The dc characteristics of granular n-type semiconductors are calculated analytically with the drift-diffusion theory. Electronic trapping at the grain boundaries (GBs) is taken into account. The use of quadratic and linear GB potential profiles in the calculation is compared. The analytical model is verified with numerical simulation performed by SILVACO ATLAS. The agreement between the analytical and numerical results is excellent in a large voltage range. The results show that electronic trapping at the GBs has a remarkable effect on the highly nonlinear I-V characteristics of the material.

  16. Krmiljenje DC motorja z mikrokrmilnikom ESP32

    Pleterski, Jan

    2017-01-01

    Sodobni mikrokrmilniki z integriranimi brezžičnimi komunikacijskimi moduli omogočajo razvoj novih aplikacij interneta stvari (ang. Internet of Things), kjer do komunikacije pride brez neposrednega človeškega posredovanja. Cilj zaključne naloge je preizkusiti mikrokrmilnik ESP32 Thing, še posebej njegove nove zmožnosti brezžične povezave. Mikrokrmilnik je preizkušan s PID krmiljenjem DC motorja s programiranjem v programskih okoljih Arduino in ESP-IDF. Zaključno delo je osredotočeno predvse...

  17. Power Oscillations Damping in DC Microgrids

    Hamzeh, Mohsen; Ghafouri, Mohsen; Karimi, Houshang; Sheshyekani, Keyhan; Guerrero, Josep M.

    2016-01-01

    This paper proposes a new control strategy for damping of power oscillations in a multi-source dc microgrid. A parallel combination of a fuel cell (FC), a photovoltaic (PV) system and a supercapacitor (SC) are used as a hybrid power conversion system (HPCS). The SC compensates for the slow transient response of the FC stack. The HPCS controller comprises a multi-loop voltage controller and a virtual impedance loop for power management. The virtual impedance loop uses a dynamic droop gain to a...

  18. Classification of electrical discharges in DC Accelerators

    Banerjee, Srutarshi, E-mail: sruban.stephens@gmail.com [Accelerator and Pulse Power Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Deb, A.K. [Department of Electrical Engineering, Indian Institute of Technology Kharagpur, Kharagpur 721302 (India); Rajan, Rehim N. [Accelerator and Pulse Power Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Kishore, N.K. [Department of Electrical Engineering, Indian Institute of Technology Kharagpur, Kharagpur 721302 (India)

    2016-08-11

    Controlled electrical discharge aids in conditioning of the system while uncontrolled discharges damage its electronic components. DC Accelerator being a high voltage system is no exception. It is useful to classify electrical discharges according to the severity. Experimental prototypes of the accelerator discharges are developed. Photomultiplier Tubes (PMTs) are used to detect the signals from these discharges. Time and Frequency domain characteristics of the detected discharges are used to extract features. Machine Learning approaches like Fuzzy Logic, Neural Network and Least Squares Support Vector Machine (LSSVM) are employed to classify the discharges. This aids in detecting the severity of the discharges.

  19. Distributed Grid Experiences in CMS DC04

    Fanfani, A; Grandi, C; Legrand, I; Suresh, S; Campana, S; Donno, F; Jank, W; Sinanis, N; Sciabà, A; García-Abia, P; Hernández, J; Ernst, M; Anzar, A; Fisk, I; Giacchetti, L; Graham, G; Heavey, A; Kaiser, J; Kuropatine, N; Perelmutov, T; Pordes, R; Ratnikova, N; Weigand, J; Wu, Y; Colling, D J; MacEvoy, B; Tallini, H; Wakefield, L; De Filippis, N; Donvito, G; Maggi, G; Bonacorsi, D; Dell'Agnello, L; Martelli, B; Biasotto, M; Fantinel, S; Corvo, M; Fanzago, F; Mazzucato, M; Tuura, L; Martin, T; Letts, J; Bockjoo, K; Prescott, C; Rodríguez, J; Zahn, A; Bradley, D

    2005-01-01

    In March-April 2004 the CMS experiment undertook a Data Challenge (DC04). During the previous 8 months CMS undertook a large simulated event production. The goal of the challenge was to run CMS reconstruction for sustained period at 25Hz in put rate, distribute the data to the CMS Tier-1 centers and analyze them at remote sites. Grid environments developed in Europe by the LHC Computing Grid (LCG) and in the US with Grid2003 were utilized to complete the aspects of the challenge. A description of the experiences, successes and lessons learned from both experiences with grid infrastructure is presented.

  20. In vitro propagation of lnula royleana DC

    Anna Stojakowska

    2011-01-01

    Full Text Available A micropropagation method, through axillary shoot proliferation, was elaborated for Inula royleana DC. (Asteraceae, a medicinal plant native of Himalaya. Primary explants (cotyledonary node explants and secondary explants (node explants of in vitro regenerated shoots of the plant, inoculated on MS medium supplemented with 0.1 μM NAA and 5.0 μM kinetin, regenerated 3.4 ± 1.2 and 5.1 ± 1.9 axillary shoots per explant, respectively. The regenerated shoots were easily rooting and adapting to growth in soil.

  1. Advances in DC photocathode electron guns

    Dunham M, Bruce; Heartmann, P.; Reza Kazimi; Hongxiu Liu; Poelker, B.M.; Price, J.S.; Rutt, P.M.; Schneider, W.J.; Sinclair K, Charles

    1998-01-01

    At Jefferson Lab, a DC photoemission gun using GaAs and GaAs-like cathodes provides a source of polarized electrons for the main accelerator. The gun is required to produce high average current with long operational lifetimes and high system throughout. Recent work has shown that careful control of the parameters affecting cathode lifetime lead to dramatic improvements in source operation. These conditions include vacuum and the related effect of ion back-bombardment, and precise control of all of the electrons emitted from the cathode. In this paper, the authors will review recent results and discuss implications for future photocathode guns

  2. Advances in DC photocathode electron guns

    Dunham, B. M.; Hartmann, P.; Kazimi, R.; Liu, H.; Poelker, B. M.; Price, J. S.; Rutt, P. M.; Schneider, W. J.; Sinclair, C. K.

    1999-01-01

    At Jefferson Lab, a DC photoemission gun using GaAs and GaAs-like cathodes provides a source of polarized electrons for the main accelerator. The gun is required to produce high average current with long operational lifetimes and high system throughput. Recent work has shown that careful control of the parameters affecting cathode lifetime lead to dramatic improvements in source operation. These conditions include vacuum and the related effect of ion backbombardment, and precise control of all of the electrons emitted from the cathode. In this paper, we will review recent results and discuss implications for future photocathode guns

  3. Advances in DC photocathode electron guns

    Dunham, B.M.; Hartmann, P.; Kazimi, R.; Liu, H.; Poelker, B.M.; Price, J.S.; Rutt, P.M.; Schneider, W.J.; Sinclair, C.K.

    1999-01-01

    At Jefferson Lab, a DC photoemission gun using GaAs and GaAs-like cathodes provides a source of polarized electrons for the main accelerator. The gun is required to produce high average current with long operational lifetimes and high system throughput. Recent work has shown that careful control of the parameters affecting cathode lifetime lead to dramatic improvements in source operation. These conditions include vacuum and the related effect of ion backbombardment, and precise control of all of the electrons emitted from the cathode. In this paper, we will review recent results and discuss implications for future photocathode guns. copyright 1999 American Institute of Physics

  4. Electronically commutated DC motor. Elektronisch kommutierter Gleichstrommotor

    Gruenleitner, H; Schalk, K; Koegler, G

    1981-08-13

    The purpose of the invention is to create a controlled and electronically commutated DC motor, so that the braking current regulator does not act with the frequency motor current regulator, where an additional switch is not required to decouple the braking current transistor while running, and where the reference value of braking current need not be greater than the reference value of motor current. According to the invention, this problem is solved by a connection, by which, while running, the braking current regulator is interlocked out by means of the output signal of the motor current regulator. A cheap diode and the associated wiring are all that is required for the interlock.

  5. Bifurcation Analysis of a DC-DC Bidirectional Power Converter Operating with Constant Power Loads

    Cristiano, Rony; Pagano, Daniel J.; Benadero, Luis; Ponce, Enrique

    Direct current (DC) microgrids (MGs) are an emergent option to satisfy new demands for power quality and integration of renewable resources in electrical distribution systems. This work addresses the large-signal stability analysis of a DC-DC bidirectional converter (DBC) connected to a storage device in an islanding MG. This converter is responsible for controlling the balance of power (load demand and generation) under constant power loads (CPLs). In order to control the DC bus voltage through a DBC, we propose a robust sliding mode control (SMC) based on a washout filter. Dynamical systems techniques are exploited to assess the quality of this switching control strategy. In this sense, a bifurcation analysis is performed to study the nonlinear stability of a reduced model of this system. The appearance of different bifurcations when load parameters and control gains are changed is studied in detail. In the specific case of Teixeira Singularity (TS) bifurcation, some experimental results are provided, confirming the mathematical predictions. Both a deeper insight in the dynamic behavior of the controlled system and valuable design criteria are obtained.

  6. Direct switching control of DC-DC power electronic converters using hybrid system theory

    Zhao, J.; Lin, F. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wang, C. [Wayne State Univ., Detroit, MI (United States). Dept. of Electrical and Computer Engineering; Wayne State Univ., Detroit, MI (United States). Div. of Engineering Technology

    2010-07-01

    A direct switching control (DSC) scheme for power electronics converters was described. The system was designed for use in both traditional and renewable energy applications as well as in electric drive vehicles. The proposed control scheme was based on a detailed hybrid system converter model that used model predictive control (MPC), piecewise affine (PWA) approximations and constrained optimal control methods. A DC-DC converter was modelled as a hybrid machine. Switching among different modes of the DC-DC converter were modelled as discrete events controlled by the hybrid controller. The modelling scheme was applied to a Buck converter. The DSC was used to control the switch of the power converter based on a hybrid machine model. Results of the study showed that the method can be used to regulate output voltage and inductor currents. The method also provides fast transient responses and effectively regulates both currents and voltage. The controller can be used to provide immediate responses to dynamic disturbances and output voltage fluctuations. 23 refs., 7 figs.

  7. A review on DC/DC converter architectures for power fuel cell applications

    Kolli, Abdelfatah; Gaillard, Arnaud; De Bernardinis, Alexandre; Bethoux, Olivier; Hissel, Daniel; Khatir, Zoubir

    2015-01-01

    Highlights: • Different DC/DC power converter topologies for Fuel Cell systems are presented. • Advantages and drawbacks of the DC/DC power converter topologies are detailed. • Wide-BandGap semiconductors are attractive candidates for design of converters. • Wide-BandGap semiconductors improve efficiency and thermal limits of converters. • Different semiconductor technologies are assessed. - Abstract: Fuel cell-based power sources are attractive devices. Through multi-stack architecture, they offer flexibility, reliability, and efficiency. Keys to accessing the market are simplifying its architecture and each components. These include, among others, the power converter enabling the output voltage regulation. This article focuses on this specific component. The present paper gives a comprehensive overview of the power converter interfaces potentially favorable for the automotive, railways, aircrafts and small stationary domains. First, with respect to the strategic development of a modular design, it defines the specifications of a basic interface. Second, it inventories the best architecture opportunities with respect to these requirements. Based on this study, it fully designs a basic module and points out the outstanding contribution of the new developed silicon carbide switch technology. In conclusion, this review article exhibits the importance of choosing the right power converter architecture and the related technology. In this context it is highlighted that the output power interface can be efficient, compact and modular. In addition, its features enable a thermal compatibility with many ways of integrating this component in the global fuel cell based power source.

  8. Control and modulation for loss minimization for dc/dc converters in wind farm

    Dincan, Catalin Gabriel; Kjær, Philip Carne

    2016-01-01

    For a DC wind turbine, a single phase series-resonant converter for unidirectional power is studied. This paper aims to identify and compare impact on electrical losses and component ratings from the choice of three candidate control strategies. The evaluation is purely based on circuit simulatio...

  9. A Four-Phase High Voltage Conversion Ratio Bidirectional DC-DC Converter for Battery Applications

    Li-Kun Xue

    2015-06-01

    Full Text Available This study presents a four-phase interleaved high voltage conversion ratio bidirectional DC-DC converter circuit based on coupled inductors and switched capacitors, which can eliminate the defects of conventional high voltage conversion ratio bidirectional DC-DC converters in terms of high-voltage/current stress, less efficiency and low-power limitation. Parallel channels are used to reduce current stress at the low-voltage side and series connected switched capacitors are used to enlarge voltage conversion ratio, reduce voltage stress and achieve auto current sharing. This paper proposes the operation principle, feature analysis and optimization design considerations. On this basis the objectives of high voltage conversion ratio, low voltage/current stress, high power density, high efficiency and high-power applications can be achieved. Some experimental results based on a 500 W prototype converter (24 V to 48 V at low-voltage side, 400 V at high-voltage side are given to verify the theoretical analysis and the effectiveness of the proposed converter.

  10. Static and Dynamic Characteristics of DC-DC Converter Using a Digital Filter

    Kurokawa, Fujio; Okamatsu, Masashi

    This paper presents the regulation and dynamic characteristics of the dc-dc converter with digital PID control, the minimum phase FIR filter or the IIR filter, and then the design criterion to improve the dynamic characteristics is discussed. As a result, it is clarified that the DC-DC converter using the IIR filter method has superior performance characteristics. The regulation range is within 1.3%, the undershoot against the step change of the load is less than 2% and the transient time is less than 0.4ms with the IIR filter method. In this case, the switching frequency is 100kHz and the step change of the load R is from 50 Ω to 10 Ω. Further, the superior characteristics are obtained when the first gain, the second gain and the second cut-off frequency are relatively large, and the first cut-off frequency and the passing frequency are relatively low. Moreover, it is important that the gain strongly decreases at the second cut-off frequency because the upper band pass frequency range must be always less than half of the sampling frequency based on the sampling theory.

  11. Exploration of Charge Recycling DC-DC Conversion Using a Switched Capacitor Regulator

    Mircea R. Stan

    2013-07-01

    Full Text Available The increasing popularity of DVFS (dynamic voltage frequency scaling schemes for portable low power applications demands highly efficient on-chip DC-DC converters. The primary aim of this work is to enable increased efficiency of on-chip DC-DC conversion for near-threshold operation of multicore chips. The idea is to supply nominal (high off-chip voltage to the cores which are then “voltage-stacked” to generate the near-threshold (low voltages based on Kirchhoff’s voltage law through charge recycling. However, the effectiveness of this implicit down-conversion is affected by the current imbalance among the cores. The paper presents a design methodology and optimization strategy for highly efficient charge recycling on-chip regulation using a push-pull switched capacitor (SC circuit. A dual-boundary hysteretic feedback control circuit has been designed for stacked loads. A stacked-voltage domain with its self-regulation capability combined with a SC converter has shown average efficiency of 78%–93% for 2:1 down-conversion with ILoad (max of 200 mA and workload imbalance varying from 0–100%.

  12. Design of interleaved multilayer rosen type piezoelectric transformer for high voltage dc/dc applications

    Rødgaard, Martin Schøler; Andersen, Thomas; Meyer, Kaspar Sinding

    2012-01-01

    Research and development within piezoelectric transformer (PT) based converters are rapidly increasing as the technology is maturing and starts to prove its capabilities. Especially for high voltage and high step-up applications, PT based converters have demonstrated good performance and DC...

  13. High Current Planar Transformer for Very High Efficiency Isolated Boost DC-DC Converters

    Pittini, Riccardo; Zhang, Zhe; Andersen, Michael A. E.

    2014-01-01

    This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac-resistance a......This paper presents a design and optimization of a high current planar transformer for very high efficiency dc-dc isolated boost converters. The analysis considers different winding arrangements, including very high copper thickness windings. The analysis is focused on the winding ac......-resistance and transformer leakage inductance. Design and optimization procedures are validated based on an experimental prototype of a 6 kW dcdc isolated full bridge boost converter developed on fully planar magnetics. The prototype is rated at 30-80 V 0-80 A on the low voltage side and 700-800 V on the high voltage side...... with a peak efficiency of 97.8% at 80 V 3.5 kW. Results highlights that thick copper windings can provide good performance at low switching frequencies due to the high transformer filling factor. PCB windings can also provide very high efficiency if stacked in parallel utilizing the transformer winding window...

  14. Light weight, high power, high voltage dc/dc converter technologies

    Kraus, Robert; Myers, Ira; Baumann, Eric

    1990-01-01

    Power-conditioning weight reductions by orders of magnitude will be required to enable the megawatt-power-level space systems envisioned by the Strategic Defense Initiative, the Air Force, and NASA. An interagency program has been initiated to develop an 0.1-kg/kW dc/dc converter technology base for these future space applications. Three contractors are in the first phase of a competitive program to develop a megawatt dc/dc converter. Researchers at NASA Lewis Research Center are investigating innovative converter topology control. Three different converter subsystems based on square wave, resonant, and super-resonant topologies are being designed. The components required for the converter designs cover a wide array of technologies. Two different switches, one semiconductor and the other gas, are under development. Issues related to thermal management and material reliability for inductors, transformers, and capacitors are being investigated in order to maximize power density. A brief description of each of the concepts proposed to meet the goals of this program is presented.

  15. Model Based Optimization of Integrated Low Voltage DC-DC Converter for Energy Harvesting Applications

    Jayaweera, H. M. P. C.; Muhtaroğlu, Ali

    2016-11-01

    A novel model based methodology is presented to determine optimal device parameters for the fully integrated ultra low voltage DC-DC converter for energy harvesting applications. The proposed model feasibly contributes to determine the maximum efficient number of charge pump stages to fulfill the voltage requirement of the energy harvester application. The proposed DC-DC converter based power consumption model enables the analytical derivation of the charge pump efficiency when utilized simultaneously with the known LC tank oscillator behavior under resonant conditions, and voltage step up characteristics of the cross-coupled charge pump topology. The verification of the model has been done using a circuit simulator. The optimized system through the established model achieves more than 40% maximum efficiency yielding 0.45 V output with single stage, 0.75 V output with two stages, and 0.9 V with three stages for 2.5 kΩ, 3.5 kΩ and 5 kΩ loads respectively using 0.2 V input.

  16. Directly coupled YBCO dc SQUID magnetometers

    Petersen, P.R.E.; Shen, Y.Q.; Holst, T.; Larsen, B.H.; Sager, M.P.; Bindslev Hansen, J.

    1999-01-01

    YBa 2 Cu 3 O 7- x magnetometers have been made on 10mmx10mm MgO substrates by directly coupling the magnetometer pick-up loop to a dc SQUID with narrow strip lines. The dc SQUIDs were made with YBa 2 Cu 3 O 7-x step-edge Josephson junctions. The layout of the magnetometer pick-up loop was chosen as a compromise between maximizing the loop effective area and minimizing the loop inductance. The SQUID was designed to have L S ∼100 pH in order to obtain β L =2I 0 L S /Φ 0 approx.= 1 with the single-junction critical current I 0 ∼10 μA. We have made magnetometers with white noise levels down to 55 fT Hz -1/2 and a 1/f knee at 1 Hz (ac biased). Noise measurements were made on a field-cooled magnetometer. The noise measured at 1 Hz when cooled in 'zero field' was 175 fT Hz -1/2 . When cooled in magnetic fields of B = 50 μT and B = 100 μT we measured the noise at 1 Hz to be 430 fT Hz -1 2 and 1.3 pT Hz -1/2 , respectively. (author)

  17. Process of DC-SC photoinjector

    Xiang Rong; Zhao Kui; Quan Shengwen; Ding Yuantao; Zhang Baocheng; Lu Xiangyang; Lin Lin; Wang Lifang; Chen Jiaer

    2004-01-01

    The DC-SC photoinjector at Beijing University is designed to provide an electron beam of average current 1 mA with the energy of 2-3 MeV and normalized rms transverse emittance of 3πmm-mrad at an 81.25 MHz repetition rate. The test facility has been completely installed in our lab. In this paper some of the ongoing experimental activities are summarized. First results from the cold test of superconducting cavity have been presented. According to the results, authors have improved the main coupler to repress the multipacting. The beam test of 100 μA on the DC gun has been done, photocathode preparation chamber can produce Cs 2 Te cathodes, and the laser system can provide laser pulse with 266 nm wavelength. The time synchronization between laser and RF power has been achieved by a timing stabilizer. A new method using 'due image pattern' of Cherenkov radiation will be commissioned to measure beam emittance. The next step is under way, to prepare all the equipment for the beam tests. (authors)

  18. Discussion - a high voltage DC generator

    Bhagwat, P.V.; Singh, Jagir; Hattangadi, V.A.

    1993-01-01

    One of the requirements for a high power ion source is a high voltage, high current DC generator. The high voltage, high current generator, DISCATRON, presently under development in our laboratory is a rotating disc type electrostatic generator similar in design to the one reported by A. Isoya et al. (1985). It is compact and rugged electrostatic DC generator based on the principle of induction charging by pellet chains used in the pelletron accelerator. It is, basically, a constant-current device with little stored energy, so that, in case of a breakdown, damage to the equipment connected to the output terminals is minimal. Since the present generator is only a proto-type, meant for a study of the practical difficulties that would be encountered in its manufacture, the output voltage and current specified has been kept quite modest viz., 300 kV at 500 μA, maximum. Some results of the preliminary tests carried out with this generator are described. (author). 4 figs

  19. Ac and dc motor flooding times

    Crowley, D.A.; Hinton, J.H.

    1988-01-01

    Reactor safety studies, such as the emergency cooling system (ECS) limits analyses and the probabilistic risk assessment, require that the flood-out times be calculated for the ac and dc motors at the -40 foot level. New calculations are needed because dams of an improved design have been installed between the pump room and motor room, and because updated leak rate calculations have shown that the maximum possible leak rate is larger than that which had been previously calculated. The methodology for calculating the motor flood-out times has also been improved. A computer program has been written to calculate flood-out times for various leak rates and sump pump operabilities. For ECS limits analyses, the worst case dc motor flood-out times are 161 and 297 seconds in LKC and P-areas, respectively. These times are for a 135,468 gpm leak that first flows to the motor room and all of the sump pumps are off

  20. Development of innovative superconducting DC power cable

    Matsushita, Teruo; Kiuchi, Masaru [Dept. of Computer Science and Electronics Kyushu Institute of Technology, Iizuka (Japan)

    2017-09-15

    It is required to reduce the cost of superconducting cable to realize a superconducting DC power network that covers a wide area in order to utilize renewable energy. In this paper a new concept of innovative cable is introduced that can enhance the current-carrying capacity even though the same superconducting tape is used. Such a cable can be realized by designing an optimal winding structure in such a way that the angle between the tape and magnetic field becomes small. This idea was confirmed by preliminary experiments for a single layer model cable made of Bi-2223 tapes and REBCO coated conductors. Experiments of three and four layer cables of practical sizes were also done and it was found that the current-carrying capacity increased as theoretically predicted. If the critical current properties of commercial superconducting tapes are further improved in a parallel magnetic field, the enhancement will become pronounced and this technology will surely contribute to realization of superconducting DC power network.

  1. Voltage Control System of A DC Generator Using PLC

    Subrata CHATTOPADHYAY; Sagarika PAL

    2008-01-01

    The voltage control system of a DC generator may suffer from high frequency oscillations without offset or low frequency oscillation with offset. A PID controller can eliminate both these errors. In the present paper, the voltage control system of a DC generator using a PLC based PID controller has been designed. Operation of PLC as a continuous controller has been described and the load characteristic of DC generator with and without controller have been determined experimentally and reporte...

  2. Treatment of hazardous wastes by DC thermal plasma arc discharge

    Toru, Iwao; Yafang, Liu; Furuta, N.; Tsuginori, Inaba

    2001-01-01

    The temperature of the DC thermal plasma arc discharge is discussed, and examples of the waste treatment for the inorganic compounds such as fly ash, asbestos, and for the organic compounds such as the toxic dioxines and TBT by using the DC plasma arc discharge are shown. In addition, the plasma treatment by using a radiant power emitted from the DC plasma arc discharge is also shown as another new kind of ones. (authors)

  3. Fundamental characteristics of the QFP measured by the dc SQUID

    Shimizu, N.; Harada, Y.; Miyamoto, N.; Hosoya, M.; Goto, E.

    1989-01-01

    This paper describes the fundamental characteristics of the Quantum Flux Parametron (QFP) measured by a new method in which the output signals of the QFP are detected with a dc SQUID. The dc SQUID linearly and continuously converts the output current of the QFP to voltage, allowing the output signal of the QFP to be measured as the voltage of the dc SQUID. Thus, the fundamental characteristics of the QFP have been experimentally confirmed in detail

  4. Brushless DC motor speed control strategy of simulation research

    Xiang Wen

    2017-01-01

    Full Text Available In view of the brushless DC motor speed regulation problem, an ideal control strategy is designed. Through the model and analysis of Brushless DC motor, the mathematical model of the brushless DC motor is obtained. By comparing three control strategies of PID control strategy, fuzzy control strategy and fuzzy PID control strategy, PID controller, fuzzy controller and fuzzy PID controller are designed respectively for simulation test. The simulation results show that the fuzzy PID controller has good control effect.

  5. Geometry Optimization of DC/RF Photoelectron Gun

    Chen Ping; Yu, David

    2005-01-01

    Pre-acceleration of photoelectrons in a pulsed, high voltage, short, dc gap and its subsequent injection into an rf gun is a promising method to improve electron beam emittance in rf accelerators. Simulation work has been performed in order to optimize the geometric shapes of a dc/rf gun and improve electron beam properties. Variations were made on cathode and anode shapes, dc gap distance, and inlet shape of the rf cavity. Simulations showed that significant improvement on the normalized emittance (< 1 mm-mrad), compared to a dc gun with flat cathode, could be obtained after the geometric shapes of the gun were optimized.

  6. Troubleshooting of Modulator DC power supply at KOMAC

    Jeong, Hae Seong; Kim, Han Sung; Kwon, Hyeok Jung; Kim, Seong Gu; Kim, Dae Il; Lee, Seok Geun; Kim, Jae Ha; Seol, Kyeong Tae; Cho, Yong Sub [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    The process of solving problems to operate the 2nd converter modulator will be introduced. Also, the PSpice simulation result about the 12-pulse rectifier will be compared with the measurement result. KOMAC (KOrea Multi-purpose Accelerator Complex) has four HVCMs (High Voltage Converter Modulator) which are the power source of nine klystrons. Four HVCMs are already operated since 2013 for operating the 100 MeV linear proton accelerator at KOMAC. This HVCM system includes the 12-pulse rectifier (ac-dc), capacitors bank (dc-link, Pos, Neg) and converter modulator (dc-dc). Especially, the 12-pulse rectifier system receives the power from the utility and converts 3,300 ac voltage to 2,200 dc voltage for supplying the dc power to the capacitors bank. This rectifier system used twelve thyristors for the rectification and applied RC snubber networks to protect the semiconductor switches (thyristors). Since the 2nd modulator dc power supply has troubled, the troubleshooting process conducted by the staves of KOMAC. It takes 3 months to solve the problems because it is not easy to find the faulty wiring. Nevertheless, our staves found the faulty point with a hope to operate the modulator system and the PSpice simulation helps to solve the problems. Using PSpice which is tool for simulating the circuit, the dc power supply abnormal phenomenon was simulated exactly. After corrected the faulty wiring, the modulator dc power supply operated.

  7. Stability of DC Voltage Droop Controllers in VSC HVDC Systems

    Thams, Florian; Suul, Jon Are; D’Arco, Salvatore

    2015-01-01

    Future multi-terminal HVDC systems are expected to utilize dc voltage droop controllers and several control implementations have been proposed in literature. This paper first classifies possible dc droop implementations in a simple framework. Then, the small-signal stability of a VSC-based conver......Future multi-terminal HVDC systems are expected to utilize dc voltage droop controllers and several control implementations have been proposed in literature. This paper first classifies possible dc droop implementations in a simple framework. Then, the small-signal stability of a VSC...

  8. Chemical profiling of infusions and decoctions of Helichrysum italicum subsp. picardii by UHPLC-PDA-MS and in vitro biological activities comparatively with green tea (Camellia sinensis) and rooibos tisane (Aspalathus linearis).

    Pereira, Catarina Guerreiro; Barreira, Luísa; Bijttebier, Sebastiaan; Pieters, Luc; Neves, Vanessa; Rodrigues, Maria João; Rivas, Ricardo; Varela, João; Custódio, Luísa

    2017-10-25

    Several medicinal plants are currently used by the food industry as functional additives, for example botanical extracts in herbal drinks. Moreover, the scientific community has recently begun focusing on halophytes as sources of functional beverages. Helichrysum italicum subsp. picardii (everlasting) is an aromatic halophyte common in southern Europe frequently used as spice and in traditional medicine. In this context, this work explored for the first time H. italicum subsp. picardii as a potential source of innovative herbal beverages with potential health promoting properties. For that purpose, infusions and decoctions were prepared from roots, vegetative aerial-organs (stems and leaves) and flowers and evaluated for in vitro antioxidant and anti-diabetic activities. Samples were also assessed for toxicity in different mammalian cell lines and chemically characterized by spectrophotometric methods and ultra-high performance liquid chromatography-photodiode array-mass-spectrometry (UHPLC-PDA-MS). Results were expressed relating to 'a cup-of-tea' and compared with those obtained with green tea (Camellia sinensis) and rooibos tisane (Aspalathus linearis). Tisanes from the everlasting's above-ground organs, particularly flowers, have high polyphenolic content and several phenolics were identified; the main compounds were chlorogenic and quinic acids, dicaffeoylquinic-acid isomers and gnaphaliin-A. The antioxidant activity of beverages from the everlasting's above-ground organs matched or surpassed that of green tea and rooibos. Its anti-diabetic activity was moderate and toxicity low. Overall, our results suggest that the everlasting is a potential source of innovative and functional herbal beverages. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Design and Implementation of Anti-windup PI Control on DC-DC Bidirectional Converter for Hybrid Vehicle Applications

    Muh. Zakiyullah Romdlony

    2012-07-01

    Full Text Available Well-regulated DC bus voltage is the important point to guarantee the power demand in hybrid vehicle applications. Voltage regulation can be achieved with control method that build switching signal on DC-DC converter. This paper describes design and small scale experimental results of bus voltage regulation control of the DC-DC bidirectional converter with battery and supercapacitor as energy source. The control system consists of two control loops, the outer loop that get DC bus voltage feedback using PI anti-windup back calculation control method. This outer loop will generate a reference current for the inner loop that implement hysteresis control. The inner control loop will compare that reference curent with the source current obtained from the current sensor. Simulation and experimental results show that bus voltage is well-regulated under the load changes with 1% voltage ripple.

  10. The Chaotic-Based Control of Three-Port Isolated Bidirectional DC/DC Converters for Electric and Hybrid Vehicles

    Zheng Wang

    2016-01-01

    Full Text Available Three-port isolated (TPI bidirectional DC/DC converters have three energy ports and offer advantages of large voltage gain, galvanic isolation ability and high power density. For this reason this kind of converters are suitable to connect different energy sources and loads in electric and hybrid vehicles. The purpose of this paper is to propose chaotic modulation and the related control scheme for TPI bidirectional DC/DC converters, in such a way that the switching harmonic peaks can be suppressed in spectrum and the conducted electromagnetic interference (EMI is reduced. Two chaotic modulation strategies, namely the continuously chaotic modulation and the discretely chaotic modulation are presented. These two chaotic modulation strategies are applied for TPI bidirectional DC/DC converters with shifted-phase angle based control and phase-shifted PWM control. Both simulation and experiments are given to verify the validity of the proposed chaotic modulation-based control schemes.

  11. PI and Fuzzy Control Strategies for High Voltage Output DC-DC Boost Power Converter - Hardware Implementation and Analysis

    Padmanaban, Sanjeevi Kumar; Blaabjerg, Frede; Siano, Pierluigi

    2016-01-01

    This paper presents the control strategies by Proportional-Integral (P-I) and Fuzzy Logic (FL) for a DC-DC boost power converter for high output voltage configuration. Standard DC-DC converters are traditionally used for high voltage direct current (HVDC) power transmission systems. But, lack its...... converter with inbuilt voltage-lift technique and overcome the aforementioned deficiencies. Further, the control strategy is adapted based on proportional-integral (P-I) and fuzzy logic, closed-loop controller to regulate the outputs and ensure the performances. Complete hardware prototype of EHV converter...... performances in terms of efficiency, reduced transfer gain and increased cost with sensor units. Moreover, the internal self-parasitic components reduce the output voltage and efficiency of classical high voltage converters (HVC). This investigation focused on extra high-voltage (EHV) DC-DC boost power...

  12. UNJUK KERJA PENGUBAH TEGANGAN DC-DC TOPOLOGI BOOST DENGAN NILAI INDUKTANSI DAN KAPASITANSI YANG DIOPTIMASI PADA KEADAAN TRANSIEN

    I Wayan Arta Wijaya

    2009-05-01

    Full Text Available Pengubah daya DC-DC topologi boost dapat menghasilkan tegangan yang lebih tinggi dari tegangan input dengan riak (ripple yang kecil dan efisiensi yang cukup tinggi. Nilai dari sebuah induktansi dan kapasitansi dari pengubah daya DC-DC dengan menggunakan topologi boost dioptimalkan menggunakan analisa transien. Fungsi ini diatur berdasarkan pada analisa dari pengubah daya selama kondisi transien. Nilai induktansi dan kapasitansi yang telah dioptimalkan dengan perhitungan dibandingkan dalam simulasi pada pengubah daya DC-DC dan hasilnya akan dibuktikan dengan menggunakan hasil percobaan. Nilai optimal untuk kapasitor dan induktor pada frekuensi 666,7 Hz, siklus kerja (duty cycle 66,7 %, resistansi output 36 Ώ dan tegangan input 12 volt adalah 1038 μF dan 11,9 mH

  13. Sliding-Mode Control of a Charger/Discharger DC/DC Converter for DC-Bus Regulation in Renewable Power Systems

    Sergio Ignacio Serna-Garcés

    2016-03-01

    Full Text Available Stand-alone power systems based on renewable energy sources are used to replace generators based on fossil fuels. Those renewable power systems also require Energy Storage Devices (ESD interfaced by a charger/discharger power converter, which consist of a bidirectional DC/DC converter, and a DC bus. This paper proposes a single sliding-mode controller (SMC for the charger/discharger DC/DC converter to provide a stable DC bus voltage in any operation condition: charging or discharging the ESD, or even without any power exchange between the ESD and the DC bus. Due to the non-linear nature of the power converter, the SMC parameters are adapted on-line to ensure global stability in any operation condition. Such stability of the adaptive SMC is mathematically demonstrated using analytical expressions for the transversality, reachability and equivalent control conditions. Moreover, a design procedure for the adaptive SMC parameters is provided in order to ensure the dynamic response required for the correct operation of the load. Finally, simulations and experimental tests validate the proposed controller and design procedure.

  14. Hybrid Non-Isolated and Non Inverting Nx Interleaved DC-DC Multilevel Boost Converter for Renewable Energy Applications

    Bhaskar, Mahajan Sagar; Kulkarni, Rishi M.; Padmanaban, Sanjeevi Kumar

    2016-01-01

    In this paper hybrid non isolated/ non inverting Nx interleaved DC-DC multilevel Boost Converter for renewable energy applications is presented. The presented hybrid topology is derived from the conventional interleaved converter and the Nx Multilevel boost converter. In renewable energy...... applications, generated energy cannot be directly used at application end. In most of the cases it needs to be stepped up with DC-DC converter at operating voltage levels as per the requirement of the application. Though conventional boost converter can theoretically be used for this purpose, but obtaining...

  15. Novel Step-Up DC/DC Converter with No Right Half Plane Zero and Reduced Switched Voltage Stress Characteristics

    Mostaan, Ali; Alizadeh, Ebrahim; Soltani, Mohsen

    2014-01-01

    and the voltage transfer gain is obtained. It is also demonstrated that the voltage stress on all semiconductor devices is restricted to input voltage which allows the utilization of a power switch with lower drain source resistance. In order to further increase the voltage gain another switched capacitor voltage......Novel step-up DC/DC converter is introduced in this paper. This converter is realized with adding the switched capacitor voltage multiplier cell to the three switch step-down DC/DC converter that has been proposed in the literature. The proposed converter is analyzed in the steady state...

  16. DC Rocks! Using Place-Based Learning to Introduce Washington DC's K-12 Students to the Geosciences

    Mayberry, G. C.; Mattietti, G. K.

    2017-12-01

    The Washington DC area has interesting geology and a multitude of agencies that deal with the geosciences, yet K-12 public school students in DC, most of whom are minorities, have limited exposure to the geosciences. Geoscience agencies in the DC area have a unique opportunity to address this by introducing the geosciences to local students who otherwise may not have such an opportunity, by highlighting the geology in the students' "backyard," and by leveraging partnerships among DC-based geoscience-related agencies. The USGS and George Mason University are developing a project called DC Rocks, which will give DC's students an exciting introduction into the world of geoscience with place-based learning opportunities that will make geoscience relevant to their lives and their futures. Both the need in DC and the potential for lasting impact are great; the geosciences have the lowest racial diversity of all the science, technology, engineering, and math (STEM) fields, 89% of students in DC public schools are minorities, and there is no dedicated geoscience curriculum in DC. DC Rocks aims to give these students early exposure to the earth sciences, and encourage them to consider careers in the profession. DC Rocks will work with partner agencies to apply several methods that are recommended by researchers to increase the participation of minority students in the geosciences, including providing profoundly positive experiences that spark interest in the geosciences (Levine et al., 2007); increasing students' sense of belonging in the geosciences (Huntoon, et al, 2016); and place-based teaching practices that emphasize the study of local sites (Semken, 2005), such as DC's Rock Creek Park. DC Rocks will apply these methods by coordinating local geoscientists and resources to provide real-world examples of the geosciences' impact on students' lives. Through the DC Rocks website, educators will be able to request geoscience-related resources such as class presentations by

  17. A Markovian Approach Applied to Reliability Modeling of Bidirectional DC-DC Converters Used in PHEVs and Smart Grids

    M. Khalilzadeh

    2016-12-01

    Full Text Available In this paper, a stochastic approach is proposed for reliability assessment of bidirectional DC-DC converters, including the fault-tolerant ones. This type of converters can be used in a smart DC grid, feeding DC loads such as home appliances and plug-in hybrid electric vehicles (PHEVs. The reliability of bidirectional DC-DC converters is of such an importance, due to the key role of the expected increasingly utilization of DC grids in modern Smart Grid. Markov processes are suggested for reliability modeling and consequently calculating the expected effective lifetime of bidirectional converters. A three-leg bidirectional interleaved converter using data of Toyota Prius 2012 hybrid electric vehicle is used as a case study. Besides, the influence of environment and ambient temperature on converter lifetime is studied. The impact of modeling the reliability of the converter and adding reliability constraints on the technical design procedure of the converter is also investigated. In order to investigate the effect of leg increase on the lifetime of the converter, single leg to five-leg interleave DC-DC converters are studied considering economical aspect and the results are extrapolated for six and seven-leg converters. The proposed method could be generalized so that the number of legs and input and output capacitors could be an arbitrary number.

  18. Well coupled, low noise, dc SQUIDS

    Muhlfelder, B.; Beall, J.A.; Cromar, M.W.; Johnson, W.W.; Ono, R.H.

    1985-01-01

    The authors have designed, fabricated, and tested a Double Transformer (DT) coupled dc SQUID (Superconducting Quantum Interference Device) with low noise, an input inductance of 1μH and a smooth input-output characteristic. A transmission line model is presented to explain a resonance in the input-output characteristic of early versions of this device. Guided by the results of numerical simulations a new version of this device has been built and tested. Experimental results are presented that show that the resonance can be moved to a higher voltage by reducing the area of the SQUID loop. The voltage-external flux characteristic of some of these new devices agrees to within 10% with computer simulations. The minimum detectable energy per unit bandwidth (MDE) referred to the SQUID loop, is 10h, where h is Planck's constant. Computer simulations indicate an MDE of 6h

  19. Electronically commutated dc motors for electric vehicles

    Maslowski, E. A.

    1981-01-01

    A motor development program to explore the feasibility of electronically commutated dc motors (also known as brushless) for electric cars is described. Two different design concepts and a number of design variations based on these concepts are discussed. One design concept is based on a permanent magnet, medium speed, machine rated at 7000 to 9000 rpm, and powered via a transistor inverter power conditioner. The other concept is based on a permanent magnet, high speed, machine rated at 22,000 to 26,000 rpm, and powered via a thyristor inverter power conditioner. Test results are presented for a medium speed motor and a high speed motor each of which have been fabricated using samarium cobalt permanent magnet material.

  20. dc glow-discharge cleaning for accelerator

    Chou, T.S.; Hseuh, H.C.

    1982-01-01

    Average pressure of 1 x 10 -11 torr and vacuum stability are necessary for the successful operation of the proton storage rings such as ISABELLE. Vacuum degassing at high temperature and in situ bake-out will reduce the thermoout-gassing rate of the beam tubes to approx. 10 -13 Tl/cm 2 sec, therefore achieving the required static pressure. The vacuum instability caused by beam-induced ion desorption can be solved by dc glow discharge cleaning. With evidence from this study, the present understanding of glow discharge in a cylindrically symmetric geometry is reviewed. Argon and argon/oxygen mixture serve as plasmas in the glow. The role of oxygen in cleaning the beam tubes during the glow discharge is demonstrated experimentally. Glow discharge cleaning with and without bake-out is also studied