Doppler Lidar Vertical Velocity Statistics Value-Added Product

Energy Technology Data Exchange (ETDEWEB)

Newsom, R. K. [DOE ARM Climate Research Facility, Washington, DC (United States); Sivaraman, C. [DOE ARM Climate Research Facility, Washington, DC (United States); Shippert, T. R. [DOE ARM Climate Research Facility, Washington, DC (United States); Riihimaki, L. D. [DOE ARM Climate Research Facility, Washington, DC (United States)

2015-07-01

Accurate height-resolved measurements of higher-order statistical moments of vertical velocity fluctuations are crucial for improved understanding of turbulent mixing and diffusion, convective initiation, and cloud life cycles. The Atmospheric Radiation Measurement (ARM) Climate Research Facility operates coherent Doppler lidar systems at several sites around the globe. These instruments provide measurements of clear-air vertical velocity profiles in the lower troposphere with a nominal temporal resolution of 1 sec and height resolution of 30 m. The purpose of the Doppler lidar vertical velocity statistics (DLWSTATS) value-added product (VAP) is to produce height- and time-resolved estimates of vertical velocity variance, skewness, and kurtosis from these raw measurements. The VAP also produces estimates of cloud properties, including cloud-base height (CBH), cloud frequency, cloud-base vertical velocity, and cloud-base updraft fraction.

Long-Term Athletic Development in Youth Alpine Ski Racing: The Effect of Physical Fitness, Ski Racing Technique, Anthropometrics and Biological Maturity Status on Injuries

Directory of Open Access Journals (Sweden)

Lisa Müller

2017-08-01

Full Text Available Alpine ski racing is known to be a sport with a high risk of injuries. Because most studies have focused mainly on top-level athletes and on traumatic injuries, limited research exists about injury risk factors among youth ski racers. The aim of this study was to determine the intrinsic risk factors (anthropometrics, biological maturity, physical fitness, racing technique for injury among youth alpine ski racers. Study participants were 81 youth ski racers attending a ski boarding school (50 males, 31 females; 9–14 years. A prospective longitudinal cohort design was used to monitor sports-related risk factors over two seasons and traumatic (TI and overuse injuries (OI. At the beginning of the study, anthropometric characteristics (body height, body weight, sitting height, body mass index; biological maturity [status age at peak height velocity (APHV]; physical performance parameters related to jump coordination, maximal leg and core strength, explosive and reactive strength, balance and endurance; and ski racing technique were assessed. Z score transformations normalized the age groups. Multivariate binary logistic regression (dependent variable: injury yes/no and multivariate linear regression analyses (dependent variable: injury severity in total days of absence from training were calculated. T-tests and multivariate analyses of variance were used to reveal differences between injured and non-injured athletes and between injury severity groups. The level of significance was set to p < 0.05. Relatively low rates of injuries were reported for both traumatic (0.63 TI/athlete and overuse injuries (0.21 OI/athlete. Athletes with higher body weight, body height, and sitting height; lower APHV values; better core flexion strength; smaller core flexion:extension strength ratio; shorter drop jump contact time; and higher drop jump reactive strength index were at a lower injury risk or more vulnerable for fewer days of absence from training. However

Determination of the barrier height for acetyl radical dissociation from acetyl chloride photodissociation at 235 nm using velocity map imaging.

Science.gov (United States)

Tang, Xiaonan; Ratliff, Britni J; FitzPatrick, Benjamin L; Butler, Laurie J

2008-12-18

This work uses velocity map imaging to determine the barrier height for acetyl radical, CH3CO, dissociation to CH3 + CO. Photodissociation of acetyl chloride at 235 nm generates acetyl radicals with an internal energy distribution spanning this barrier. We determine the velocity and internal energy distribution of all nascent acetyl radicals, stable and unstable, by measuring the velocities of the Cl(2P3/2) and Cl(2P1/2) cofragments. These Cl cofragments are detected with 2 + 1 resonance-enhanced multiphoton ionization (REMPI) in a spin-orbit branching ratio Cl(2P3/2):Cl(2P1/2) of 3.3 +/- 0.2. Using 157 nm photoionization, we then detect the recoil velocities of the energetically stable acetyl radicals. The radicals and momentum matched Cl atoms evidence parallel angular distributions. Comparison of the total recoil translational energy distribution P(E(T)) for all radicals to that obtained from the detection of stable radicals yields an onset for dissociation at a translational energy of 25.0 +/- 0.4 kcal/mol. From this onset we can calculate the barrier height for CH3CO --> CH3 + CO, but this relies on prior determinations of the C-Cl bond energy of acetyl chloride. Using an experimental bond dissociation energy of 83.4 +/- 0.2 kcal/mol yields a dissociation barrier of 14.2 +/- 0.5 kcal/mol. Our data evidence that a portion of the acetyl radicals formed with total internal energy above the barrier are stable due to the partitioning of energy into rotation during the C-Cl bond fission of the precursor. Thus, the internal energy onset for dissociation is not as sharp as was assumed in prior determinations of the barrier. The experimentally determined onset is compared with that predicted from electronic structure calculations at the G3//B3LYP and CCSD(T) levels of theory.

Effect of firing conditions & release height on terminal performance of submunitions and conditions for optimum height of release

Directory of Open Access Journals (Sweden)

L.K. Gite

2017-06-01

Full Text Available Submunitions should exhibit optimum terminal performance at target end when released from certain pre-determined height. Selection of an optimum height of release of the submunitions depends on the terminal parameters like forward throw, remaining velocity, impact angle and flight time. In this paper, the effects of initial firing conditions and height of release on terminal performance of submunitions discussed in detail. For different height of release, the relation between range and forward throw is also established & validated for a number of firing altitude and rocket configurations.

Changes in Sprint and Jump Performances After Traditional, Plyometric, and Combined Resistance Training in Male Youth Pre- and Post-Peak Height Velocity.

Science.gov (United States)

Lloyd, Rhodri S; Radnor, John M; De Ste Croix, Mark B A; Cronin, John B; Oliver, Jon L

2016-05-01

The purpose of this study was to compare the effectiveness of 6-week training interventions using different modes of resistance (traditional strength, plyometric, and combined training) on sprinting and jumping performances in boys before and after peak height velocity (PHV). Eighty school-aged boys were categorized into 2 maturity groups (pre- or post-PHV) and then randomly assigned to (a) plyometric training, (b) traditional strength training, (c) combined training, or (d) a control group. Experimental groups participated in twice-weekly training programs for 6 weeks. Acceleration, maximal running velocity, squat jump height, and reactive strength index data were collected pre- and postintervention. All training groups made significant gains in measures of sprinting and jumping irrespective of the mode of resistance training and maturity. Plyometric training elicited the greatest gains across all performance variables in pre-PHV children, whereas combined training was the most effective in eliciting change in all performance variables for the post-PHV cohort. Statistical analysis indicated that plyometric training produced greater changes in squat jump and acceleration performances in the pre-PHV group compared with the post-PHV cohort. All other training responses between pre- and post-PHV cohorts were not significant and not clinically meaningful. The study indicates that plyometric training might be more effective in eliciting short-term gains in jumping and sprinting in boys who are pre-PHV, whereas those who are post-PHV may benefit from the additive stimulus of combined training.

Assessment of loaded squat jump height with a free-weight barbell and Smith machine: comparison of the take-off velocity and flight time procedures.

Science.gov (United States)

Pérez-Castilla, Alejandro; McMahon, John J; Comfort, Paul; García-Ramos, Amador

2017-07-31

The aims of this study were to compare the reliability and magnitude of jump height between the two standard procedures of analysing force platform data to estimate jump height (take-off velocity [TOV] and flight time [FT]) in the loaded squat jump (SJ) exercise performed with a free-weight barbell and in a Smith machine. Twenty-three collegiate men (age 23.1 ± 3.2 years, body mass 74.7 ± 7.3 kg, height 177.1 ± 7.0 cm) were tested twice for each SJ type (free-weight barbell and Smith machine) with 17, 30, 45, 60, and 75 kg loads. No substantial differences in reliability were observed between the TOV (Coefficient of variation [CV]: 9.88%; Intraclass correlation coefficient [ICC]: 0.82) and FT (CV: 8.68%; ICC: 0.88) procedures (CV ratio: 1.14), while the Smith SJ (CV: 7.74%; ICC: 0.87) revealed a higher reliability than the free-weight SJ (CV: 9.88%; ICC: 0.81) (CV ratio: 1.28). The TOV procedure provided higher magnitudes of jump height than the FT procedure for the loaded Smith machine SJ (systematic bias: 2.64 cm; Pfree-weight SJ exercise (systematic bias: 0.26 cm; P>0.05). Heteroscedasticity of the errors was observed for the Smith machine SJ (r: 0.177) with increasing differences in favour of the TOV procedure for the trials with lower jump height (i.e. higher external loads). Based on these results the use of a Smith machine in conjunction with the FT more accurately determine jump height during the loaded SJ.

Height profile of particle concentration in an aeolian saltating cloud: A wind tunnel investigation by PIV MSD

Science.gov (United States)

Dong, Zhibao; Wang, Hongtao; Zhang, Xiaohang; Ayrault, Michael

2003-10-01

Attempt is made to define the particle concentration in an aeolian saltating cloud and its variation with height using artificial spherical quartz sand in a wind tunnel. The height profiles of the relative particle concentration in aeolian saltating cloud at three wind velocities were detected by the state of the art PIV (Particle Image Velocimetry) MSD (Mie Scattering Diffusion) technique, and converted to actual concentration based on sand transport rate and the variation with height of velocity of the saltating cloud. The particle concentration was found to decay exponentially with height and to increase with wind velocity. It decayed more rapidly when the wind velocity decreased. The volume/volume concentration in the near-surface layer was at the order of 10-4. The results obtained by PIV MSD technique were in good agreement with those derived from the sand flux and velocity profiles, the former being about 15% greater than the later.

Ethnic Differences in Peripheral Skeletal Development Among Urban South African Adolescents: A Ten-Year Longitudinal pQCT Study.

Science.gov (United States)

Schoenbuchner, Simon M; Pettifor, John M; Norris, Shane A; Micklesfield, Lisa K; Prentice, Ann; Ward, Kate A

2017-12-01

There are no longitudinal pQCT data of bone growth and development from sub-Saharan Africa, where rapid environmental, societal, and economic transitions are occurring, and where fracture rates are predicted to rise. The aim of this study was to compare skeletal development in black and white South African adolescents using longitudinal data from the Birth to Twenty study. The Birth to Twenty Bone Health subcohort consisted of 543 adolescents (261 [178 black] girls, 282 [201 black] boys). Annual pQCT measurements of the radial and tibial metaphysis and diaphysis were obtained between ages 12 and 22 years (distal metaphysis: cross-sectional area [CSA] and trabecular bone mineral density [BMD]; diaphysis: total and cortical CSA, cortical BMD, and polar stress-strain index [SSIp]). Age at peak height velocity (APHV) was calculated to account for differences in maturational timing between ethnic groups and sexes. Mixed-effects models were used to describe trajectories for each pQCT outcome. Likelihood-ratio tests were used to summarize the overall difference in trajectories between black and white participants within each sex. APHV (mean ± SD years) was similar in black (11.8 ± 0.8) and white (12.2 ± 1.0) girls, but delayed in black (14.2 ± 1.0) relative to white boys (13.3 ± 0.8). By 4 years post-APHV, white adolescents had significantly greater cortical CSA and SSIp than black adolescents at the radius. There were no significant differences at the radial metaphysis but there was some divergence, such that black adolescents had greater radial trabecular BMD by the end of follow-up. At the tibia, white adolescents had lower diaphyseal CSA and SSIp, and greater metaphyseal CSA. There was no ethnic difference in tibial trabecular BMD. There are ethnic differences in bone growth and development, independent of maturation, in South African adolescents. This work gives new insights into the possible etiology of childhood fractures, which occur most

Peak height velocity as an alternative for maturational classification associated with motor performance

Directory of Open Access Journals (Sweden)

Leonardo Trevizan Costa

2009-01-01

Full Text Available Adolescence is a phase characterized by important physical and maturational alterations, with individuals of the same chronological age, but who are more mature, may present sportive advantages because of greater force gain and additional muscle mass. Thus, in studies evaluating motor skills of children and adolescents, maturational classification should be an efficient and easily applicable tool in order to facilitate the interpretation of the true relationship between maturation and motor performance. Therefore, the objective of this study was to compare the relationship between motor performance and different types of classification of biological maturation in 209 boys aged to 17 years (11.59 ± 2.57 practicing soccer. Anthropometric variables were obtained according to the ISAK criteria. Biological maturation was determined based on age at peak height velocity (PHV and also by self-assessment of sexual maturation (genitalia and pubic hair. Motor performance was evaluated by sit-and-reach tests, horizontal jump, modified push-ups, 50-m run, and 9/12-min run/walk. The results showed progression in the variables analyzed as the subjects reached maturity. Correlation analysis and the egression values indicated higher consistency for the PHV classification, which better explained motor performance according to maturational status, exceeding the values obtained by comparison according to age or sexual maturation. Thus, the use of PHV as a classification instrument is preferably recommended for youngsters with haracteristics similar to those of the present sample.

Validation of the iPhone app using the force platform to estimate vertical jump height.

Science.gov (United States)

Carlos-Vivas, Jorge; Martin-Martinez, Juan P; Hernandez-Mocholi, Miguel A; Perez-Gomez, Jorge

2018-03-01

Vertical jump performance has been evaluated with several devices: force platforms, contact mats, Vertec, accelerometers, infrared cameras and high-velocity cameras; however, the force platform is considered the gold standard for measuring vertical jump height. The purpose of this study was to validate an iPhone app called My Jump, that measures vertical jump height by comparing it with other methods that use the force platform to estimate vertical jump height, namely, vertical velocity at take-off and time in the air. A total of 40 sport sciences students (age 21.4±1.9 years) completed five countermovement jumps (CMJs) over a force platform. Thus, 200 CMJ heights were evaluated from the vertical velocity at take-off and the time in the air using the force platform, and from the time in the air with the My Jump mobile application. The height obtained was compared using the intraclass correlation coefficient (ICC). Correlation between APP and force platform using the time in the air was perfect (ICC=1.000, PJump, is an appropriate method to evaluate the vertical jump performance; however, vertical jump height is slightly overestimated compared with that of the force platform.

Mathematical model for logarithmic scaling of velocity fluctuations in wall turbulence.

Science.gov (United States)

Mouri, Hideaki

2015-12-01

For wall turbulence, moments of velocity fluctuations are known to be logarithmic functions of the height from the wall. This logarithmic scaling is due to the existence of a characteristic velocity and to the nonexistence of any characteristic height in the range of the scaling. By using the mathematics of random variables, we obtain its necessary and sufficient conditions. They are compared with characteristics of a phenomenological model of eddies attached to the wall and also with those of the logarithmic scaling of the mean velocity.

EFFECTS OF RUN-UP VELOCITY ON PERFORMANCE, KINEMATICS, AND ENERGY EXCHANGES IN THE POLE VAULT

Directory of Open Access Journals (Sweden)

Nicholas P. Linthorne

2012-06-01

Full Text Available This study examined the effect of run-up velocity on the peak height achieved by the athlete in the pole vault and on the corresponding changes in the athlete's kinematics and energy exchanges. Seventeen jumps by an experienced male pole vaulter were video recorded in the sagittal plane and a wide range of run-up velocities (4.5-8.5 m/s was obtained by setting the length of the athlete's run-up (2-16 steps. A selection of performance variables, kinematic variables, energy variables, and pole variables were calculated from the digitized video data. We found that the athlete's peak height increased linearly at a rate of 0.54 m per 1 m/s increase in run-up velocity and this increase was achieved through a combination of a greater grip height and a greater push height. At the athlete's competition run-up velocity (8.4 m/s about one third of the rate of increase in peak height arose from an increase in grip height and about two thirds arose from an increase in push height. Across the range of run-up velocities examined here the athlete always performed the basic actions of running, planting, jumping, and inverting on the pole. However, he made minor systematic changes to his jumping kinematics, vaulting kinematics, and selection of pole characteristics as the run-up velocity increased. The increase in run-up velocity and changes in the athlete's vaulting kinematics resulted in substantial changes to the magnitudes of the energy exchanges during the vault. A faster run-up produced a greater loss of energy during the take-off, but this loss was not sufficient to negate the increase in run-up velocity and the increase in work done by the athlete during the pole support phase. The athlete therefore always had a net energy gain during the vault. However, the magnitude of this gain decreased slightly as run-up velocity increased

The Effect of Plyometric Training Volume on Athletic Performance in Prepubertal Male Soccer Players.

Science.gov (United States)

Chaabene, Helmi; Negra, Yassine

2017-10-01

To assess and compare the effects of 8 wk of in-season (2 sessions/wk) low- and high-volume plyometric training (PT) on measures of physical fitness in prepubertal male soccer players. A total of 25 soccer players were randomly assigned to a low-volume PT group (LPT; n = 13, age 12.68 ± 0.23 y, age at peak height velocity [APHV] 14.25 ± 0.29 y, maturity offset -1.57 ± 0.29 y) or a high-volume PT group (HPT; n = 12, age 12.72 ± 0.27 y, APHV 14.33 ± 0.77 y, maturity offset -1.61 ± 0.76 y). A linear-sprint test (5-m, 10-m, 20-m, and 30-m), change-of-direction (CoD) test, and vertical- (squat-jump [SJ]), countermovement- (CMJ), and horizontal-jump (standing long jump [SLJ]) test were carried out before and after 8 wk of PT. There was a significant main effect of time for sprint outcomes (5-m, P = .005, ES = 0.86; 10-m, P = .006, ES = 0.85; 20-m, P = .03, ES = 0.64, and 30-m, P = .05, ES = 0.57), CoD (P = .002, ES = 0.96), SJ (P = .008, ES = 0.81; CMJ, P = .01, ES = 0.73), and SLJ ability (P = .007, ES = 0.83). There were no significant training group × time interactions in any measured outcomes. After 8 wk of training, results showed similar performance improvement on measures of sprint time, CoD, and jumping ability between LPT and HPT groups. From a time-efficiency perspective, it is recommended to use LPT in prepubertal male soccer players to improve their proxies of athletic performance.

The Role of a Relative Age Effect in the 7 International Children’s Winter Games 2016 and the Influence of Biological Maturity Status on Selection

Directory of Open Access Journals (Sweden)

Lisa Müller, Carolin Hildebrandt, Christian Raschner

2017-06-01

Full Text Available The aim of this study was to analyse the role of a relative age effect (RAE and to investigate the influence of biological maturity status on the RAE at the 7th International Children`s Winter Games. The birth dates of all 572 participants (365 males, 207 females were analysed, and the biological maturity status of 384 athletes (243 males, 141 females was assessed by the age at peak height velocity (APHV method. A RAE was present in the total sample (χ2 = 67.81; p < 0.001, and among both male (χ2 = 49.02; p < 0.001 and female athletes (χ2 = 37.00; p < 0.001 as well as for strength- (χ2 = 56.46; p < 0.001, endurance- (χ2 = 20.48; p = 0.039 and technique-related types of sports (χ2 = 20.48; p = 0.041. No significant differences in biological maturity status were present between the male athletes of single relative age quarters. Among the female athletes a significant difference was present (F = 5.94, p < 0.001; relatively younger female athletes had significantly lower values in the APHV, which indicated that they were maturing earlier. However, when dividing the athletes into normal, early and late maturing athletes, it could be seen that among the relatively younger athletes, hardly any late maturing athletes were present. These findings revealed that relatively younger athletes seemed to only have a chance for selection if they were early maturing, whereas relatively older athletes had an increased likelihood for selection independent of their biological maturity status. In the future, the relative age and the biological maturity status should be considered in the talent development system for various types of winter sport, to contribute to more fairness and to not discriminate against relatively younger and less mature athletes.

Wake interaction and power production of variable height model wind farms

International Nuclear Information System (INIS)

Vested, M H; Sørensen, J N; Hamilton, N; Cal, R B

2014-01-01

Understanding wake dynamics is an ongoing research topic in wind energy, since wakes have considerable effects on the power production when wind turbines are placed in a wind farm. Wind tunnel experiments have been conducted to study the wake to wake interaction in a model wind farm in tandem with measurements of the extracted power. The aim is to investigate how alternating mast height influences the interaction of the wakes and the power production. Via the use of stereo-particle image velocimetry, the flow field was obtained in the first and last rows of the wind turbine array as a basis of comparison. It was found that downstream of the exit row wind turbine, the power was increased by 25% in the case of a staggered height configuration. This is partly due to the fact that the taller turbines reach into a flow area with a softened velocity gradient. Another aspect is that the wake downstream of a tall wind turbine to some extent passes above the standard height wind turbine. Overall the experiments show that the velocity field downstream of the exit row changes considerably when the mast height is alternating

Ten years statistics of wind direction and wind velocity measurements performed at the Karlsruhe Nuclear Research Center

International Nuclear Information System (INIS)

Becker, M.; Dilger, H.

1979-06-01

The measurements of wind direction and wind velocity performed at 60 m and 200 m height were evaluated for one year each and frequency distributions of the measured values were established. The velocity was divided into 1 m/s steps and the direction into 10 0 sectors. The frequency distribution of the wind direction reveals three maxima located in the southwest, northeast and north, respectively. The maximum of the frequency distribution of the wind velocity occurs between 4 and 5 m/s at 200 m height and between 3 and 4 m/s at 60 m height. (orig.) [de

Wind‐gust parametrizations at heights relevant for wind energy: a study based on mast observations

DEFF Research Database (Denmark)

Suomi, I.; Vihma, T.; Gryning, Sven-Erik

2013-01-01

Wind gusts are traditionally observed and reported at the reference height of 10 m and most gust parametrization methods have been developed only for this height. In many practical applications, e.g. in wind energy, the relevant heights are, however, up to a few hundred metres. In this study, mean...... speed, which is parametrized on the basis of the surface friction velocity, the Obukhov length and height and the boundary‐layer height. The new gust parametrization method outperformed the two older methods: the effects of surface roughness, stability and the height above the surface were well...

Doubly Disadvantaged? The Relative Age Effect in Poland’s Basketball Players

Directory of Open Access Journals (Sweden)

Krystian Rubajczyk, Kamil Świerzko, Andrzej Rokita

2017-06-01

Full Text Available The aim of this study was to identify the relative age effect (RAE in young Polish male (n = 3849 and female (n = 3419 basketball players aged 14 to 22 years competing in the elite games of the Polish Youth Championships. The distribution of birth dates, body height, players’ match statistics, and the results of teams participating in championships were identified. The RAE was observed in male and female group, regardless of players age. Nevertheless, the greatest disproportion in the distribution of dates of birth was found in U16 group of boys (V = 0.25, p < 0.0001. Significant differences in body height were identified in U14 and U16 groups of boys (p < 0.0001 and U14 group of girls (p < 0.01. The RAE was the most detrimental in the group of boys from teams ranked 9th or lower (p < 0.0001. The groups of male and female basketball players from the top 3 teams had the highest average body height (p < 0.001. In U14 boys, significantly higher match results and performance index ratings (PIR were observed for players born in the first half of a calendar year. The research results show the impact of the RAE on the success of youth basketball teams in Poland. The month of birth, body height and sex may determine sporting achievements in youth basketball. Coaches should consider the chronological age and pubertal growth acceleration (APHV-age at peak height velocity of players to optimize the process of identifying gifted basketball players, especially among boys of 14 years of age.

Increases of Chamber Height and Base Diameter Have Contrasting Effects on Grazing Rate of Two Cladoceran Species: Implications for Microcosm Studies

Science.gov (United States)

Pan, Ying; Zhang, Yunshu; Peng, Yan; Zhao, Qinghua; Sun, Shucun

2015-01-01

Aquatic microcosm studies often increase either chamber height or base diameter (to increase water volume) to test spatial ecology theories such as “scale” effects on ecological processes, but it is unclear whether the increase of chamber height or base diameter have the same effect on the processes, i.e., whether the effect of the shape of three-dimensional spaces is significant. We orthogonally manipulated chamber height and base diameter and determined swimming activity, average swimming velocity and grazing rates of the cladocerans Daphnia magna and Moina micrura (on two algae Scenedesmus quadricauda and Chlorella vulgaris; leading to four aquatic algae-cladoceran systems in total) under different microcosm conditions. Across all the four aquatic systems, increasing chamber height at a given base diameter significantly decreased the duration and velocity of horizontal swimming, and it tended to increase the duration but decrease the velocity of vertical swimming. These collectively led to decreases in both average swimming velocity and grazing rate of the cladocerans in the tall chambers (at a given base diameter), in accordance with the positive relationship between average swimming velocity and grazing rate. In contrast, an increase of base diameter at a given chamber height showed contrasting effects on the above parameters. Consistently, at a given chamber volume increasing ratio of chamber height to base diameter decreased the average swimming velocity and grazing rate across all the aquatic systems. In general, increasing chamber depth and base diameter may exert contrasting effects on zooplankton behavior and thus phytoplankton-zooplankton interactions. We suggest that spatial shape plays an important role in determining ecological process and thus should be considered in a theoretical framework of spatial ecology and also the physical setting of aquatic microcosm experiments. PMID:26273836

Pulsar velocity observations: Correlations, interpretations, and discussion

International Nuclear Information System (INIS)

Helfand, D.J.; Tademaru, E.

1977-01-01

From an examination of the current sample of 12 pulsars with measured proper motions and the z-distribution of the much larger group of over 80 sources with measured period derivatives, we develop a self-consistent picture of pulsar evolution. The apparent tendency of pulsars to move parallel to the galactic plane is explained as the result of various selection effects. A method for calculating the unmeasurable radial velocity of a pulsar is presented; it is shown that the total space velocities thus obtained are consistent with the assumption of an extreme Population I origin for pulsars which subsequently move away from the plane with a large range of velocities. The time scale for pulsar magnetic field decay is derived from dynamical considerations. A strong correlation of the original pulsar field strength with the magnitude of pulsar velocity is discussed. This results in the division of pulsars into two classes: Class A sources characterized by low space velocities, a small scale height, and low values of P 0 P 0 ; and Class B sources with a large range of velocities (up to 1000 km s -1 ), a much greater scale height, and larger values of initial field strength. It is postulated that Class A sources originate in tight binaries where their impulse acceleration at birth is insufficient to remove them from the system, while the Class B sources arise from single stars or loosely bound binaries and are accelerated to high velocities by their asymmetric radiation force. The evolutionary picture which is developed is shown to be consistent with a number of constraints imposed by supernova rates, the relative frequency of massive binaries and Class A sources, theoretical field-decay times, and the overall pulsar galactic distribution

CUTLASS HF radar observations of high-velocity E-region echoes

Directory of Open Access Journals (Sweden)

M. V. Uspensky

Full Text Available A short event of high-velocity E-region echo observations by the Pykkvibaer HF radar is analysed to study echo parameters and the echo relation to the Farley-Buneman plasma instability. The echoes were detected in several beams aligned closely to the magnetic L-shell direction. Two echo groups were identified: one group corresponded to the classical type 1 echoes with velocities close to the nominal ion-acoustic speed of 400 ms^–1 , while the other group had significantly larger velocities, of the order of 700 ms^–1 . The mutual relationship between the echo power, Doppler velocity, spectral width and elevation angles for these two groups was studied. Plotting of echo parameters versus slant range showed that all ~700 ms^–1 echoes originated from larger heights and distances of 500–700 km, while all ~400 ms^–1 echoes came from lower heights and from farther distances; 700–1000 km. We argue that both observed groups of echoes occurred due to the Farley-Buneman plasma instability excited by strong ( ~70 mVm^–1 and uniformly distributed electric fields. We show that the echo velocities for the two groups were different because the echoes were received from different heights. Such a separation of echo heights occurred due to the differing amounts of ionospheric refraction at short and large ranges. Thus, the ionospheric refraction and related altitude modulation of ionospheric parameters are the most important factors to consider, when various characteristics of E-region decametre irregularities are derived from HF radar measurements.

Key words. Ionosphere (ionospheric irregularities; plasma waves and instabilities; polar ionosphere

Throwing velocity and kinematics in elite male water polo players.

Science.gov (United States)

Melchiorri, G; Padua, E; Padulo, J; D'Ottavio, S; Campagna, S; Bonifazi, M

2011-12-01

Fifty-three members of the Italian Men Water Polo Team were filmed using two synchronized cameras, while they were shooting a goal. Considering the differences in body mass, height, training strategies and the technical-tactical features of the players, the aims of this study were to employ video-analysis techniques in order to investigate selected kinematic parameters in water polo throwing, and to provide comprehensive quantitative information on the throwing movement in relation to the different team player positions. Video analysis was used to estimate the elbow angle at release, the shoulder angle at follow through, the back and head height at ball release, trunk rotation angle and ball velocity at release. Ball release velocities ranged from 21.0 to 29.8 m/s (average value 25.3±1.4 m/s), for field players. Goal keepers show the lowest team values (average 21.7±0.3 m/s). Similar to previous study results, ball release was typically reached just prior to the elbow approaching full extension (151.6±3.6°), and the follow through shoulder angle was 143±5.9°. No significant statistical difference was recorded between injured and non-injured athletes. No positive association was demonstrated between physical characteristics (body mass and height) and ball velocity.

Simulation of three-phase flow and lance height effect on the cavity shape

Science.gov (United States)

Dong, Kai; Zhu, Rong; Gao, Wei; Liu, Fu-hai

2014-06-01

A three-dimensional computational fluid dynamics (CFD) model was developed to simulate a 150-t top-blown converter. The effect of different lance heights on the cavity shape was investigated using the volume of fluid (VOF) method. Numerical simulation results can reflect the actual molten bath surface waves impinged by the supersonic oxygen jets. With increasing lance height, the cavity depth decreases, and the cavity area, varying like a parabola, increases and then decreases. The cavity area maximizes at the lance height of 1.3 m. Under the three different lance heights simulated in this study, all of the largest impact velocities at the molten bath surface are between 50 m/s and 100 m/s.

Relating Time-Dependent Acceleration and Height Using an Elevator

Science.gov (United States)

Kinser, Jason M.

2015-01-01

A simple experiment in relating a time-dependent linear acceleration function to height is explored through the use of a smartphone and an elevator. Given acceleration as a function of time, a(t), the velocity function and position functions are determined through integration as in v(t)=? a(t) dt (1) and x(t)=? v(t) dt. Mobile devices such as…

Sexual Orientation, Objective Height, and Self-Reported Height.

Science.gov (United States)

Skorska, Malvina N; Bogaert, Anthony F

2017-01-01

Studies that have used mostly self-reported height have found that androphilic men and women are shorter than gynephilic men and women, respectively. This study examined whether an objective height difference exists or whether a psychosocial account (e.g., distortion of self-reports) may explain these putative height differences. A total of 863 participants, recruited at a Canadian university, the surrounding region, and through lesbian, gay, bisexual, and transgender (LGBT) events across Canada, self-reported their height and had their height measured. Androphilic men were shorter, on average, than gynephilic men. There was no objective height difference between gynephilic, ambiphilic, and androphilic women. Self-reported height, statistically controlling for objective height, was not related to sexual orientation. These findings are the first to show an objective height difference between androphilic and gynephilic men. Also, the findings suggest that previous studies using self-reported height found part of a true objective height difference between androphilic and gynephilic men. These findings have implications for existing biological theories of men's sexual orientation development.

Analysis of lift-off height and structure of n-heptane tribrachial flames in laminar jet configuration

KAUST Repository

Luca, Stefano

2015-03-30

A set of lifted tribrachial n-heptane flames in a laminar jet configuration are simulated. The simulations are performed using finite rate chemistry and detailed transport, and aim at investigating the propagation of tribrachial flames. Varying the inlet velocity of the fuel, different stabilization heights are obtained, and the dependence of the stabilization height in the inlet velocity is compared with experimental data. A detailed analysis of the flame geometry is performed by comparingthe flame structure to that of unstretched premixed flames. Issues related to differential diffusion effects, flame stretch, and transport of heat and mass from the burnt gases to the flame front are discussed.

Analysis of lift-off height and structure of n-heptane tribrachial flames in laminar jet configuration

KAUST Repository

Luca, Stefano; Bisetti, Fabrizio

2015-01-01

A set of lifted tribrachial n-heptane flames in a laminar jet configuration are simulated. The simulations are performed using finite rate chemistry and detailed transport, and aim at investigating the propagation of tribrachial flames. Varying the inlet velocity of the fuel, different stabilization heights are obtained, and the dependence of the stabilization height in the inlet velocity is compared with experimental data. A detailed analysis of the flame geometry is performed by comparingthe flame structure to that of unstretched premixed flames. Issues related to differential diffusion effects, flame stretch, and transport of heat and mass from the burnt gases to the flame front are discussed.

The importance of postural cues for determining eye height in immersive virtual reality.

Science.gov (United States)

Leyrer, Markus; Linkenauger, Sally A; Bülthoff, Heinrich H; Mohler, Betty J

2015-01-01

In human perception, the ability to determine eye height is essential, because eye height is used to scale heights of objects, velocities, affordances and distances, all of which allow for successful environmental interaction. It is well understood that eye height is fundamental to determine many of these percepts. Yet, how eye height itself is provided is still largely unknown. While the information potentially specifying eye height in the real world is naturally coincident in an environment with a regular ground surface, these sources of information can be easily divergent in similar and common virtual reality scenarios. Thus, we conducted virtual reality experiments where we manipulated the virtual eye height in a distance perception task to investigate how eye height might be determined in such a scenario. We found that humans rely more on their postural cues for determining their eye height if there is a conflict between visual and postural information and little opportunity for perceptual-motor calibration is provided. This is demonstrated by the predictable variations in their distance estimates. Our results suggest that the eye height in such circumstances is informed by postural cues when estimating egocentric distances in virtual reality and consequently, does not depend on an internalized value for eye height.

The importance of postural cues for determining eye height in immersive virtual reality.

Directory of Open Access Journals (Sweden)

Markus Leyrer

Full Text Available In human perception, the ability to determine eye height is essential, because eye height is used to scale heights of objects, velocities, affordances and distances, all of which allow for successful environmental interaction. It is well understood that eye height is fundamental to determine many of these percepts. Yet, how eye height itself is provided is still largely unknown. While the information potentially specifying eye height in the real world is naturally coincident in an environment with a regular ground surface, these sources of information can be easily divergent in similar and common virtual reality scenarios. Thus, we conducted virtual reality experiments where we manipulated the virtual eye height in a distance perception task to investigate how eye height might be determined in such a scenario. We found that humans rely more on their postural cues for determining their eye height if there is a conflict between visual and postural information and little opportunity for perceptual-motor calibration is provided. This is demonstrated by the predictable variations in their distance estimates. Our results suggest that the eye height in such circumstances is informed by postural cues when estimating egocentric distances in virtual reality and consequently, does not depend on an internalized value for eye height.

The influence of retention on the plate height in ion-exchange chromatography

DEFF Research Database (Denmark)

Hansen, Ernst; Mollerup, Jørgen

2004-01-01

The plate heights for the amino acid tyrosine (anion exchange) and the polypeptide aprotinin (cation exchange) were determined on a porous media (Resource 15) and a get filled media (HyperD 20) at salt concentrations ranging from weak to strong retention. At a constant velocity, measurements showed....... In this article, the rate of mass transfer in the particles is described by three different rate mechanisms, pore diffusion, solid diffusion, and parallel diffusion. The van Deemter equation was used to model the data to determine the mass-transfer properties. The development of the plate height with increasing...... retention revealed a characteristic behavior for each rate mechanism. In the pore diffusion model, the plate height increased toward a constant value at strong retention, while the plate height in the solid diffusion model decreased, approaching a constant value at strong retention. In the parallel...

Should tsunami simulations include a nonzero initial horizontal velocity?

Science.gov (United States)

Lotto, Gabriel C.; Nava, Gabriel; Dunham, Eric M.

2017-08-01

Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require initial conditions on sea surface height and depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). Full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor confirm that substantial horizontal momentum is imparted to the ocean. However, almost all of that initial momentum is carried away by ocean acoustic waves, with negligible momentum imparted to the tsunami. We also compare tsunami propagation in each simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial velocity. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves from ocean acoustic and seismic waves at some final time, and backpropagating the tsunami waves to their initial state by solving the

An applied model for the height of the daytime mixed layer and the entrainment zone

DEFF Research Database (Denmark)

Batchvarova, E.; Gryning, Sven-Erik

1994-01-01

A model is presented for the height of the mixed layer and the depth of the entrainment zone under near-neutral and unstable atmospheric conditions. It is based on the zero-order mixed layer height model of Batchvarova and Gryning (1991) and the parameterization of the entrainment zone depth......-layer height: friction velocity, kinematic heat flux near the ground and potential temperature gradient in the free atmosphere above the entrainment zone. When information is available on the horizontal divergence of the large-scale flow field, the model also takes into account the effect of subsidence...

Importance of peak height velocity timing in terms of injuries in talented soccer players

NARCIS (Netherlands)

van der Sluis, A; Elferink-Gemser, Marije; Brink, M S; Visscher, C

The purpose of this study was to identify differences in traumatic and overuse injury incidence between talented soccer players who differ in the timing of their adolescent growth spurt. 26 soccer players (mean age 11.9 ± 0.84 years) were followed longitudinally for 3 years around Peak Height

Biological Maturity Status Strongly Intensifies the Relative Age Effect in Alpine Ski Racing.

Directory of Open Access Journals (Sweden)

Lisa Müller

Full Text Available The relative age effect (RAE is a well-documented phenomenon in youth sports. This effect exists when the relative age quarter distribution of selected athletes shows a biased distribution with an over-representation of relatively older athletes. In alpine ski racing, it exists in all age categories (national youth levels up to World Cup. Studies so far could demonstrate that selected ski racers are relatively older, taller and heavier. It could be hypothesized that relatively younger athletes nearly only have a chance for selection if they are early maturing. However, surprisingly this influence of the biological maturity status on the RAE could not be proven, yet. Therefore, the aim of the present study was to investigate the influence of the biological maturity status on the RAE in dependence of the level of competition. The study investigated 372 elite youth ski racers: 234 provincial ski racers (P-SR; high level of competition and 137 national ski racers (N-SR; very high level of competition. Anthropometric characteristics were measured to calculate the age at peak height velocity (APHV as an indicator of the biological maturity status. A significant RAE was present among both P-SR and N-SR, with a larger effect size among the latter group. The N-SR significantly differed in APHV from the P-SR. The distribution of normal, early and late maturing athletes significantly differed from the expected normal distribution among the N-SR, not among the P-SR. Hardly any late maturing N-SR were present; 41.7% of the male and 34% of the female N-SR of the last relative age quarter were early maturing. These findings clearly demonstrate the significant influence of the biological maturity status on the selection process of youth alpine ski racing in dependence of the level of competition. Relatively younger athletes seem to have a chance of selection only if they are early maturing.

CHANG-ES. IX. Radio scale heights and scale lengths of a consistent sample of 13 spiral galaxies seen edge-on and their correlations

Science.gov (United States)

Krause, Marita; Irwin, Judith; Wiegert, Theresa; Miskolczi, Arpad; Damas-Segovia, Ancor; Beck, Rainer; Li, Jiang-Tao; Heald, George; Müller, Peter; Stein, Yelena; Rand, Richard J.; Heesen, Volker; Walterbos, Rene A. M.; Dettmar, Ralf-Jürgen; Vargas, Carlos J.; English, Jayanne; Murphy, Eric J.

2018-03-01

Aim. The vertical halo scale height is a crucial parameter to understand the transport of cosmic-ray electrons (CRE) and their energy loss mechanisms in spiral galaxies. Until now, the radio scale height could only be determined for a few edge-on galaxies because of missing sensitivity at high resolution. Methods: We developed a sophisticated method for the scale height determination of edge-on galaxies. With this we determined the scale heights and radial scale lengths for a sample of 13 galaxies from the CHANG-ES radio continuum survey in two frequency bands. Results: The sample average values for the radio scale heights of the halo are 1.1 ± 0.3 kpc in C-band and 1.4 ± 0.7 kpc in L-band. From the frequency dependence analysis of the halo scale heights we found that the wind velocities (estimated using the adiabatic loss time) are above the escape velocity. We found that the halo scale heights increase linearly with the radio diameters. In order to exclude the diameter dependence, we defined a normalized scale height h˜ which is quite similar for all sample galaxies at both frequency bands and does not depend on the star formation rate or the magnetic field strength. However, h˜ shows a tight anticorrelation with the mass surface density. Conclusions: The sample galaxies with smaller scale lengths are more spherical in the radio emission, while those with larger scale lengths are flatter. The radio scale height depends mainly on the radio diameter of the galaxy. The sample galaxies are consistent with an escape-dominated radio halo with convective cosmic ray propagation, indicating that galactic winds are a widespread phenomenon in spiral galaxies. While a higher star formation rate or star formation surface density does not lead to a higher wind velocity, we found for the first time observational evidence of a gravitational deceleration of CRE outflow, e.g. a lowering of the wind velocity from the galactic disk.

Wake interaction and power production of variable height model wind farms

DEFF Research Database (Denmark)

Vested, Malene Hovgaard; Hamilton, N.; Sørensen, Jens Nørkær

2014-01-01

of comparison. It was found that downstream of the exit row wind turbine, the power was increased by 25% in the case of a staggered height configuration. This is partly due to the fact that the taller turbines reach into a flow area with a softened velocity gradient. Another aspect is that the wake downstream...

Strength and Power Correlates of Throwing Velocity on Subelite Male Cricket Players.

Science.gov (United States)

Freeston, Jonathan L; Carter, Thomas; Whitaker, Gary; Nicholls, Owen; Rooney, Kieron B

2016-06-01

Throwing velocity is an important aspect of fielding in cricket to affect run-outs and reduce the opponent's run-scoring opportunities. Although a relationship between strength and/or power and throwing velocity has been well established in baseball, water polo, and European handball, it has not been adequately explored in cricket. Consequently, this study aimed to determine the relationship between measures of strength and/or power and throwing velocity in cricket players. Seventeen male cricket players (mean ± SD; age, 21.1 ± 1.6 years; height, 1.79 ± 0.06 m; weight, 79.8 ± 6.4 kg) from an elite athlete program were tested for maximal throwing velocity from the stretch position and after a 3-meter shuffle. They were also assessed for strength and power using a range of different measures. Throwing velocity from the stretch position (30.5 ± 2.4 m·s) was significantly related to dominant leg lateral-to-medial jump (LMJ) distance (r = 0.71; p velocity and medicine ball chest pass (MB CP) distance (r = 0.67; p bench press strength (p = 0.90), height (p = 0.33), or weight (p = 0.29). Multiple regression analysis revealed that dominant MB Rot and MB CP explained 66% of the variance. The results were similar for velocity after a shuffle step (31.8 ± 2.1 m·s); however, VJ height reached statistical significance (r = 0.51; p ≤ 0.05). The multiple regression was also similar with MB Rot and MB CP explaining 70% of the variance. The cricketers in this study threw with greater velocity than elite junior and subelite senior cricketers but with lower velocities than elite senior cricketers and collegiate level and professional baseball players. This is the first study to demonstrate a link between strength and/or power and throwing velocity in cricket players and highlight the importance of power development as it relates to throwing velocity. Exercises that more closely simulated the speed (body weight jumps and medicine ball throws) or movement pattern (shoulder IR

Response to growth hormone treatment and final height after cranial or craniospinal irradiation

International Nuclear Information System (INIS)

Sulmont, V.; Brauner, R.; Fontoura, M.; Rappaport, R.

1990-01-01

Growth hormone (GH) deficiency (GHD) induced by cranial irradiation has become a frequent indication of hGH substitutive therapy. This study analyses the growth response to hGH therapy and the factors involved in the decrease in growth velocity observed after cranial irradiation. One hundred children given cranial radiation for pathology distant from the hypothalamo-pituitary area were studied. Fifty-six of them received hGH therapy for GHD resulting in decreased growth velocity. The initial annual height gain in the cranial-irradiated group was comparable to that of patients treated for idiopathic GHD; additional spinal irradiation significantly reduced the growth response. Twenty-eight hGH-treated patients reached final heights which were compared to those of 2 untreated irradiated groups, one with GHD (n=27) and the other with normal GH secretion (n=17). The height SD score changes observed in hGH therapy were +0.3 in the cranial (n=10) and -1.2 SD in the craniospinal (n=18) groups. GH deficiency had contributed to a mean height loss of 1 SD and spinal irradiation to a loss of 1.4SD. The small effect of hGH therapy on final height is probably linked to the small bone age retardation at onset of hGH therapy and to the fact that irradiated children entered puberty at a younger age in terms of chronological age and bone age than the idiopathic GHD patients. These data suggest that the results of gGH therapy in irradiated children might be improved with higher and more fractionated hGH doses and, in some patients, by delaying puberty using luteinizing hormone releasing hormone analogs

Response to growth hormone treatment and final height after cranial or craniospinal irradiation

Energy Technology Data Exchange (ETDEWEB)

Sulmont, V.; Brauner, R.; Fontoura, M.; Rappaport, R. (Hospital des Enfants Malades, Paris (France). Pediatric Endocrinology Unit and INSERM U30)

1990-01-01

Growth hormone (GH) deficiency (GHD) induced by cranial irradiation has become a frequent indication of hGH substitutive therapy. This study analyses the growth response to hGH therapy and the factors involved in the decrease in growth velocity observed after cranial irradiation. One hundred children given cranial radiation for pathology distant from the hypothalamo-pituitary area were studied. Fifty-six of them received hGH therapy for GHD resulting in decreased growth velocity. The initial annual height gain in the cranial-irradiated group was comparable to that of patients treated for idiopathic GHD; additional spinal irradiation significantly reduced the growth response. Twenty-eight hGH-treated patients reached final heights which were compared to those of 2 untreated irradiated groups, one with GHD (n=27) and the other with normal GH secretion (n=17). The height SD score changes observed in hGH therapy were +0.3 in the cranial (n=10) and -1.2 SD in the craniospinal (n=18) groups. GH deficiency had contributed to a mean height loss of 1 SD and spinal irradiation to a loss of 1.4SD. The small effect of hGH therapy on final height is probably linked to the small bone age retardation at onset of hGH therapy and to the fact that irradiated children entered puberty at a younger age in terms of chronological age and bone age than the idiopathic GHD patients. These data suggest that the results of gGH therapy in irradiated children might be improved with higher and more fractionated hGH doses and, in some patients, by delaying puberty using luteinizing hormone releasing hormone analogs.

Application of Displacement Height and Surface Roughness Length to Determination Boundary Layer Development Length over Stepped Spillway

Directory of Open Access Journals (Sweden)

Xiangju Cheng

2014-12-01

Full Text Available One of the most uncertain parameters in stepped spillway design is the length (from the crest of boundary layer development. The normal velocity profiles responding to the steps as bed roughness are investigated in the developing non-aerated flow region. A detailed analysis of the logarithmic vertical velocity profiles on stepped spillways is conducted through experimental data to verify the computational code and numerical experiments to expand the data available. To determine development length, the hydraulic roughness and displacement thickness, along with the shear velocity, are needed. This includes determining displacement height d and surface roughness length z0 and the relationship of d and z0 to the step geometry. The results show that the hydraulic roughness height ks is the primary factor on which d and z0 depend. In different step height, step width, discharge and intake Froude number, the relations d/ks = 0.22–0.27, z0/ks = 0.06–0.1 and d/z0 = 2.2–4 result in a good estimate. Using the computational code and numerical experiments, air inception will occur over stepped spillway flow as long as the Bauer-defined boundary layer thickness is between 0.72 and 0.79.

Effective pollutant emission heights for atmospheric transport modelling based on real-world information.

Science.gov (United States)

Pregger, Thomas; Friedrich, Rainer

2009-02-01

Emission data needed as input for the operation of atmospheric models should not only be spatially and temporally resolved. Another important feature is the effective emission height which significantly influences modelled concentration values. Unfortunately this information, which is especially relevant for large point sources, is usually not available and simple assumptions are often used in atmospheric models. As a contribution to improve knowledge on emission heights this paper provides typical default values for the driving parameters stack height and flue gas temperature, velocity and flow rate for different industrial sources. The results were derived from an analysis of the probably most comprehensive database of real-world stack information existing in Europe based on German industrial data. A bottom-up calculation of effective emission heights applying equations used for Gaussian dispersion models shows significant differences depending on source and air pollutant and compared to approaches currently used for atmospheric transport modelling.

Ballistic transport through graphene nanostructures of velocity and potential barriers

International Nuclear Information System (INIS)

Krstajic, P M; Vasilopoulos, P

2011-01-01

We investigate the electronic properties of graphene nanostructures when the Fermi velocity and the electrostatic potential vary in space. First, we consider the transmission T and conductance G through single and double barriers. We show that G for velocity barriers differs markedly from that for potential barriers for energies below the height of the latter and it exhibits periodic oscillations as a function of the energy for strong velocity modulation. Special attention is given to superlattices (SLs). It is shown that an applied bias can efficiently widen or shrink the allowed minibands of velocity-modulated SLs. The spectrum in the Kronig-Penney limit is periodic in the strength of the barriers. Collimation of an electron beam incident on an SL with velocity and potential barriers is present but it disappears when the potential barriers are absent. The number of additional Dirac points may change considerably if barriers and wells have sufficiently different Fermi velocities.

Memory for target height is scaled to observer height.

Science.gov (United States)

Twedt, Elyssa; Crawford, L Elizabeth; Proffitt, Dennis R

2012-04-01

According to the embodied approach to visual perception, individuals scale the environment to their bodies. This approach highlights the central role of the body for immediate, situated action. The present experiments addressed whether body scaling--specifically, eye-height scaling--occurs in memory when action is not immediate. Participants viewed standard targets that were either the same height as, taller than, or shorter than themselves. Participants then viewed a comparison target and judged whether the comparison was taller or shorter than the standard target. Participants were most accurate when the standard target height matched their own heights, taking into account postural changes. Participants were biased to underestimate standard target height, in general, and to push standard target height away from their own heights. These results are consistent with the literature on eye-height scaling in visual perception and suggest that body scaling is not only a useful metric for perception and action, but is also preserved in memory.

Childhood height, adult height, and the risk of prostate cancer

DEFF Research Database (Denmark)

Bjerregaard, Lise Geisler; Aarestrup, Julie; Gamborg, Michael

2016-01-01

PURPOSE: We previously showed that childhood height is positively associated with prostate cancer risk. It is, however, unknown whether childhood height exerts its effects independently of or through adult height. We investigated whether and to what extent childhood height has a direct effect...... on the risk of prostate cancer apart from adult height. METHODS: We included 5,871 men with height measured at ages 7 and 13 years in the Copenhagen School Health Records Register who also had adult (50-65 years) height measured in the Danish Diet, Cancer and Health study. Prostate cancer status was obtained...... through linkage to the Danish Cancer Registry. Direct and total effects of childhood height on prostate cancer risk were estimated from Cox regressions. RESULTS: From 1996 to 2012, 429 prostate cancers occurred. Child and adult heights were positively and significantly associated with prostate cancer risk...

Velocity loss as an indicator of neuromuscular fatigue during resistance training.

Science.gov (United States)

Sánchez-Medina, Luis; González-Badillo, Juan José

2011-09-01

This study aimed to analyze the acute mechanical and metabolic response to resistance exercise protocols (REP) differing in the number of repetitions (R) performed in each set (S) with respect to the maximum predicted number (P). Over 21 exercise sessions separated by 48-72 h, 18 strength-trained males (10 in bench press (BP) and 8 in squat (SQ)) performed 1) a progressive test for one-repetition maximum (1RM) and load-velocity profile determination, 2) tests of maximal number of repetitions to failure (12RM, 10RM, 8RM, 6RM, and 4RM), and 3) 15 REP (S × R[P]: 3 × 6[12], 3 × 8[12], 3 × 10[12], 3 × 12[12], 3 × 6[10], 3 × 8[10], 3 × 10[10], 3 × 4[8], 3 × 6[8], 3 × 8[8], 3 × 3[6], 3 × 4[6], 3 × 6[6], 3 × 2[4], 3 × 4[4]), with 5-min interset rests. Kinematic data were registered by a linear velocity transducer. Blood lactate and ammonia were measured before and after exercise. Mean repetition velocity loss after three sets, loss of velocity pre-post exercise against the 1-m·s load, and countermovement jump height loss (SQ group) were significant for all REP and were highly correlated to each other (r = 0.91-0.97). Velocity loss was significantly greater for BP compared with SQ and strongly correlated to peak postexercise lactate (r = 0.93-0.97) for both SQ and BP. Unlike lactate, ammonia showed a curvilinear response to loss of velocity, only increasing above resting levels when R was at least two repetitions higher than 50% of P. Velocity loss and metabolic stress clearly differs when manipulating the number of repetitions actually performed in each training set. The high correlations found between mechanical (velocity and countermovement jump height losses) and metabolic (lactate, ammonia) measures of fatigue support the validity of using velocity loss to objectively quantify neuromuscular fatigue during resistance training.

Fall from heights: does height really matter?

Science.gov (United States)

Alizo, G; Sciarretta, J D; Gibson, S; Muertos, K; Romano, A; Davis, J; Pepe, A

2018-06-01

Fall from heights is high energy injuries and constitutes a fraction of all fall-related trauma evaluations while bearing an increase in morbidity and mortality. We hypothesize that despite advancements in trauma care, the overall survivability has not improved in this subset of trauma patients. All adult trauma patients treated after sustaining a fall from heights during a 40-month period were retrospectively reviewed. Admission demographics, clinical data, fall height (ft), injury patterns, ISS, GCS, length of stay, and mortality were reviewed. 116 patients sustained a fall from heights, 90.4% accidental. A mean age of 37± 14.7 years, 86% male, and a fall height of 19 ± 10 ft were encountered. Admission GCS was 13 ± 2 with ISS 10 ± 11. Overall LOS was 6.6 ± 14.9 days and an ICU LOS of 2.8 ± 8.9 days. Falls ≥ 25 ft.(16%) had lower GCS 10.4 ± 5.8, increased ISS 22.6 ± 13.8, a fall height 37.9 ± 13.1 ft and associated increased mortality (p < 0.001). Mortality was 5.2%, a mean distance fallen of 39 ± 22 ft. and an ISS of 31.5 ±16.5. Brain injury was the leading cause of death, 50% with open skull fractures. Level of height fallen is a good predictor of overall outcome and survival. Despite advances in trauma care, death rates remain unchanged. Safety awareness and injury prevention programs are needed to reduce the risk of high-level falls.

Boundary layer height estimation by sodar and sonic anemometer measurements

International Nuclear Information System (INIS)

Contini, D; Cava, D; Martano, P; Donateo, A; Grasso, F M

2008-01-01

In this paper an analysis of different methods for the calculation of the boundary layer height (BLH) using sodar and ultrasonic anemometer measurements is presented. All the methods used are based on single point surface measurements. In particular the automatic spectral routine developed for Remtech sodar is compared with the results obtained with the parameterization of the vertical velocity variance, with the calculation of a prognostic model and with a parameterization based on horizontal velocity spectra. Results indicate that in unstable conditions the different methods provide similar pattern, with BLH relatively low, even if the parameterization of the vertical velocity variance is affected by a large scatter that limits its efficiency in evaluating the BLH. In stable nocturnal conditions the performances of the Remtech routine are lower with respect to the ones in unstable conditions. The spectral method, applied to sodar or sonic anemometer data, seems to be the most promising in order to develop an efficient routine for BLH determination

Rotational Angles and Velocities During Down the Line and Diagonal Across Court Volleyball Spikes

OpenAIRE

Justin R. Brown; Bader J. Alsarraf; Mike Waller; Patricia Eisenman; Charlie A. Hicks-Little

2014-01-01

The volleyball spike is an explosive movement that is frequently used to end a rally and earn a point. High velocity spikes are an important skill for a successful volleyball offense. Although the influence of vertical jump height and arm velocity on spiked ball velocity (SBV) have been investigated, little is known about the relationship of shoulder and hip angular kinematics with SBV. Other sport skills, like the baseball pitch share similar movement patterns and suggest trunk rotation is i...

Effect of Core Training on Male Handball Players’ Throwing Velocity

OpenAIRE

Manchado, Carmen; García-Ruiz, José; Cortell-Tormo, Juan M.; Tortosa Martínez, Juan

2017-01-01

Abstract In handball, throwing velocity is considered to be one of the essential factors in achieving the ultimate aim of scoring a goal. The objective of the present study was to analyze the effect of a core training program on throwing velocity in 30 handball players (age 18.7 ? 3.4 years, body height 179.3 ? 7.0 cm, body mass 78.9 ? 7.7 kg), 16 of whom were in the junior category and 14 of whom were in the senior category. The 30 players were randomly divided into two groups, the control g...

No Effect of Assisted Hip Rotation on Bat Velocity.

Science.gov (United States)

Rivera, Michelle; Leyva, Whitney D; Archer, David C; Munger, Cameron N; Watkins, Casey M; Wong, Megan A; Dobbs, Ian J; Galpin, Andrew J; Coburn, Jared W; Brown, Lee E

2018-01-01

Softball and baseball are games that require multiple skill sets such as throwing, hitting and fielding. Players spend a copious amount of time in batting practice in order to be successful hitters. Variables commonly associated with successful hitting include bat velocity and torso rotation. The concept of overspeed bodyweight assistance (BWA) has shown increases in vertical jump and sprint times, but not hip rotation and batting. The purpose of this study was to examine the effects of assisted hip rotation on bat velocity. Twenty-one male and female recreational softball and baseball players (15 males, age 23.8 ± 3.1yrs; height 177.67 ± 6.71cm; body mass 85.38 ± 14.83kg; 6 females, age 21.5 ± 2.1yrs; height 162.20 ± 9.82cm; body mass 60.28 ± 9.72kg) volunteered to participate. Four different BWA conditions (0%, 10%, 20%, and 30%) were randomly applied and their effects on bat velocity were analyzed. Subjects performed three maximal effort swings under each condition in a custom measurement device and average bat velocity (MPH) was used for analysis. A mixed factor ANOVA revealed no interaction (p=0.841) or main effect for condition, but there was a main effect for sex where males had greater bat velocity (43.82±4.40 - 0% BWA, 41.52±6.09 - 10% BWA, 42.59±7.24 - 20% BWA, 42.69±6.42 - 30% BWA) than females (32.57±5.33 - 0% BWA, 31.69±3.40 - 10% BWA, 32.43±5.06 - 20% BWA, 32.08±4.83 - 30% BWA) across all conditions Using the concept of overspeed training with assisted hip rotation up to 30% BWA did not result in an increase in bat velocity. Future research should examine elastic band angle and hip translation at set-up.

No Effect of Assisted Hip Rotation on Bat Velocity

Science.gov (United States)

RIVERA, MICHELLE; LEYVA, WHITNEY D.; ARCHER, DAVID C.; MUNGER, CAMERON N.; WATKINS, CASEY M.; WONG, MEGAN A.; DOBBS, IAN J.; GALPIN, ANDREW J.; COBURN, JARED W.; BROWN, LEE E.

2018-01-01

Softball and baseball are games that require multiple skill sets such as throwing, hitting and fielding. Players spend a copious amount of time in batting practice in order to be successful hitters. Variables commonly associated with successful hitting include bat velocity and torso rotation. The concept of overspeed bodyweight assistance (BWA) has shown increases in vertical jump and sprint times, but not hip rotation and batting. The purpose of this study was to examine the effects of assisted hip rotation on bat velocity. Twenty-one male and female recreational softball and baseball players (15 males, age 23.8 ± 3.1yrs; height 177.67 ± 6.71cm; body mass 85.38 ± 14.83kg; 6 females, age 21.5 ± 2.1yrs; height 162.20 ± 9.82cm; body mass 60.28 ± 9.72kg) volunteered to participate. Four different BWA conditions (0%, 10%, 20%, and 30%) were randomly applied and their effects on bat velocity were analyzed. Subjects performed three maximal effort swings under each condition in a custom measurement device and average bat velocity (MPH) was used for analysis. A mixed factor ANOVA revealed no interaction (p=0.841) or main effect for condition, but there was a main effect for sex where males had greater bat velocity (43.82±4.40 - 0% BWA, 41.52±6.09 - 10% BWA, 42.59±7.24 - 20% BWA, 42.69±6.42 - 30% BWA) than females (32.57±5.33 - 0% BWA, 31.69±3.40 - 10% BWA, 32.43±5.06 - 20% BWA, 32.08±4.83 - 30% BWA) across all conditions Using the concept of overspeed training with assisted hip rotation up to 30% BWA did not result in an increase in bat velocity. Future research should examine elastic band angle and hip translation at set-up. PMID:29795730

Stress wave velocity patterns in the longitudinal-radial plane of trees for defect diagnosis

Science.gov (United States)

Guanghui Li; Xiang Weng; Xiaocheng Du; Xiping Wang; Hailin Feng

2016-01-01

Acoustic tomography for urban tree inspection typically uses stress wave data to reconstruct tomographic images for the trunk cross section using interpolation algorithm. This traditional technique does not take into account the stress wave velocity patterns along tree height. In this study, we proposed an analytical model for the wave velocity in the longitudinal–...

Effects of pressure drop and superficial velocity on the bubbling fluidized bed incinerator.

Science.gov (United States)

Wang, Feng-Jehng; Chen, Suming; Lei, Perng-Kwei; Wu, Chung-Hsing

2007-12-01

Since performance and operational conditions, such as superficial velocity, pressure drop, particles viodage, and terminal velocity, are difficult to measure on an incinerator, this study used computational fluid dynamics (CFD) to determine numerical solutions. The effects of pressure drop and superficial velocity on a bubbling fluidized bed incinerator (BFBI) were evaluated. Analytical results indicated that simulation models were able to effectively predict the relationship between superficial velocity and pressure drop over bed height in the BFBI. Second, the models in BFBI were simplified to simulate scale-up beds without excessive computation time. Moreover, simulation and experimental results showed that minimum fluidization velocity of the BFBI must be controlled in at 0.188-3.684 m/s and pressure drop was mainly caused by bed particles.

Prenatal influences on size, velocity and tempo of infant growth: findings from three contemporary cohorts.

Directory of Open Access Journals (Sweden)

Costanza Pizzi

Full Text Available Studying prenatal influences of early life growth is relevant to life-course epidemiology as some of its features have been linked to the onset of later diseases.We studied the association between prenatal maternal characteristics (height, age, parity, education, pre-pregnancy body mass index (BMI, smoking, gestational diabetes and hypertension and offspring weight trajectories in infancy using SuperImposition by Translation And Rotation (SITAR models, which parameterize growth in terms of three biologically interpretable parameters: size, velocity and tempo. We used data from three contemporary cohorts based in Portugal (GXXI, n=738, Italy (NINFEA, n=2,925, and Chile (GOCS, n=959.Estimates were generally consistent across the cohorts for maternal height, age, parity and pre-pregnancy overweight/obesity. Some exposures only affected one growth parameter (e.g. maternal height (per cm: 0.4% increase in size (95% confidence interval (CI:0.3; 0.5, others were either found to affect size and velocity (e.g. pre-pregnancy underweight vs normal weight: smaller size (-4.9%, 95% CI:-6.5; -3.3, greater velocity (5.9%, 95% CI:1.9;10.0, or to additionally influence tempo (e.g. pre-pregnancy overweight/obesity vs normal weight: increased size (7.9%, 95% CI:4.9;10.8, delayed tempo (0.26 months, 95% CI:0.11;0.41, decreased velocity (-4.9%, 95% CI: -10.8;0.9.By disentangling the growth parameters of size, velocity and tempo, we found that prenatal maternal characteristics, especially maternal smoking, pre-pregnancy overweight and underweight, parity and gestational hypertension, are associated with different aspects of infant weight growth. These results may offer insights into the mechanisms governing infant growth.

Thumb Ossification Composite Index (TOCI) for Predicting Peripubertal Skeletal Maturity and Peak Height Velocity in Idiopathic Scoliosis: A Validation Study of Premenarchal Girls with Adolescent Idiopathic Scoliosis Followed Longitudinally Until Skeletal Maturity.

Science.gov (United States)

Hung, Alec L H; Chau, W W; Shi, B; Chow, Simon K; Yu, Fiona Y P; Lam, T P; Ng, Bobby K W; Qiu, Y; Cheng, Jack C Y

2017-09-06

Accurate skeletal maturity assessment is important to guide clinical evaluation of idiopathic scoliosis, but commonly used methods are inadequate or too complex for rapid clinical use. The objective of the study was to propose a new simplified staging method, called the thumb ossification composite index (TOCI), based on the ossification pattern of the 2 thumb epiphyses and the adductor sesamoid bone; to determine its accuracy in predicting skeletal maturation when compared with the Sanders simplified skeletal maturity system (SSMS); and to validate its interrater and intrarater reliability. Hand radiographs of 125 girls, acquired when they were newly diagnosed with idiopathic scoliosis prior to menarche and during longitudinal follow-up until skeletal maturity (a minimum of 4 years), were scored with the TOCI and SSMS. These scores were compared with digital skeletal age (DSA) and radius, ulna, and small hand bones (RUS) scores; anthropometric data; peak height velocity; and growth-remaining profiles. Correlations were analyzed with the chi-square test, Spearman and Cramer V correlation methods, and receiver operating characteristic curve analysis. Reliability analysis using the intraclass correlation (ICC) was conducted. Six hundred and forty-five hand radiographs (average, 5 of each girl) were scored. The TOCI staging system was highly correlated with the DSA and RUS scores (r = 0.93 and 0.92, p systems predicted peak height velocity with comparable accuracy, with a strong Cramer V association (0.526 and 0.466, respectively; p 0.97. The new proposed TOCI could provide a simplified staging system for the assessment of skeletal maturity of subjects with idiopathic scoliosis. The index needs to be subjected to further multicenter validation in different ethnic groups.

Effective pollutant emission heights for atmospheric transport modelling based on real-world information

International Nuclear Information System (INIS)

Pregger, Thomas; Friedrich, Rainer

2009-01-01

Emission data needed as input for the operation of atmospheric models should not only be spatially and temporally resolved. Another important feature is the effective emission height which significantly influences modelled concentration values. Unfortunately this information, which is especially relevant for large point sources, is usually not available and simple assumptions are often used in atmospheric models. As a contribution to improve knowledge on emission heights this paper provides typical default values for the driving parameters stack height and flue gas temperature, velocity and flow rate for different industrial sources. The results were derived from an analysis of the probably most comprehensive database of real-world stack information existing in Europe based on German industrial data. A bottom-up calculation of effective emission heights applying equations used for Gaussian dispersion models shows significant differences depending on source and air pollutant and compared to approaches currently used for atmospheric transport modelling. - The comprehensive analysis of real-world stack data provides detailed default parameter values for improving vertical emission distribution in atmospheric modelling

The Measurement of cloud velocity using the pulsed laser and image tracking technique

Energy Technology Data Exchange (ETDEWEB)

Kwon, Seong-Ouk; Baik, Seung-Hoon; Park, Seung-Kyu; Park, Nak-Gyu; Kim, Dong-lyul; Ahn, Yong-Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The height of the clouds is also important for the three dimensional radiative interaction of aerosols and clouds, since the radiative effects vary strongly depending whether the cloud is above, below or even embedded in an aerosol layer. Clouds play an important role in climate change, in the prediction of local weather, and also in aviation safety when instrument assisted flying is unavailable. Presently, various ground-based instruments used for the measurements of the cloud base height or velocity. Lidar techniques are powerful and have many applications in climate studies, including the clouds' temperature measurement, the aerosol particle properties, etc. Otherwise, it is very circumscribed in cloud velocity measurements In this paper, we propose a new method to measure the cloud velocity. In this paper, we presented a method for the measurement of the cloud altitude and velocity using lidar's range detection and the tracking system. For the lidar system, we used an injection-seeded pulsed Nd:YAG laser as the transmitter to measure the distance to the target clouds. We used the DIC system to track the cloud image and calculate the actual displacement per unit time. The configured lidar system acquired the lidar signal of clouds at a distance of about 4 km. The developed fast correlation algorithm of the tracking, which is used to track the fast moving cloud relatively, was efficient for measuring the cloud velocity in real time. The measurement values had a linear distribution.

Validity and reliability of the Myotest accelerometric system for the assessment of vertical jump height.

Science.gov (United States)

Casartelli, Nicola; Müller, Roland; Maffiuletti, Nicola A

2010-11-01

The aim of the present study was to verify the validity and reliability of the Myotest accelerometric system (Myotest SA, Sion, Switzerland) for the assessment of vertical jump height. Forty-four male basketball players (age range: 9-25 years) performed series of squat, countermovement and repeated jumps during 2 identical test sessions separated by 2-15 days. Flight height was simultaneously quantified with the Myotest system and validated photoelectric cells (Optojump). Two calculation methods were used to estimate the jump height from Myotest recordings: flight time (Myotest-T) and vertical takeoff velocity (Myotest-V). Concurrent validity was investigated comparing Myotest-T and Myotest-V to the criterion method (Optojump), and test-retest reliability was also examined. As regards validity, Myotest-T overestimated jumping height compared to Optojump (p 0.98), that is, excellent validity. Myotest-V overestimated jumping height compared to Optojump (p 12 cm), high limits of agreement ratios (>36%), and low ICCs (9 cm). In conclusion, Myotest-T is a valid and reliable method for the assessment of vertical jump height, and its use is legitimate for field-based evaluations, whereas Myotest-V is neither valid nor reliable.

Concurrent validity and reliability of torso-worn inertial measurement unit for jump power and height estimation.

Science.gov (United States)

Rantalainen, Timo; Gastin, Paul B; Spangler, Rhys; Wundersitz, Daniel

2018-09-01

The purpose of the present study was to evaluate the concurrent validity and test-retest repeatability of torso-worn IMU-derived power and jump height in a counter-movement jump test. Twenty-seven healthy recreationally active males (age, 21.9 [SD 2.0] y, height, 1.76 [0.7] m, mass, 73.7 [10.3] kg) wore an IMU and completed three counter-movement jumps a week apart. A force platform and a 3D motion analysis system were used to concurrently measure the jumps and subsequently derive power and jump height (based on take-off velocity and flight time). The IMU significantly overestimated power (mean difference = 7.3 W/kg; P jump heights exhibited poorer concurrent validity (ICC = 0.72 to 0.78) and repeatability (ICC = 0.68) than flight-time-derived jump heights, which exhibited excellent validity (ICC = 0.93 to 0.96) and reliability (ICC = 0.91). Since jump height and power are closely related, and flight-time-derived jump height exhibits excellent concurrent validity and reliability, flight-time-derived jump height could provide a more desirable measure compared to power when assessing athletic performance in a counter-movement jump with IMUs.

Concordant preferences for actual height and facial cues to height

OpenAIRE

Re, Daniel Edward; Perrett, David I.

2012-01-01

Physical height has a well-documented effect on human mate preferences. In general, both sexes prefer opposite-sex romantic relationships in which the man is taller than the woman, while individual preferences for height are affected by a person’s own height. Research in human mate choice has demonstrated that attraction to facial characteristics, such as facial adiposity, may reflect references for body characteristics. Here, we tested preferences for facial cues to height. In general, incre...

Peak power, force, and velocity during jump squats in professional rugby players

OpenAIRE

Turner, Anthony P; Unholz, Cedric N; Potts, Neill; Coleman, Simon

2012-01-01

Training at the optimal load for peak power output (PPO) has been proposed as a method for enhancing power output, although others argue that the force, velocity, and PPO are of interest across the full range of loads. The aim of this study was to examine the influence of load on PPO, peak barbell velocity (BV), and peak vertical ground reaction force (VGRF) during the jump squat (JS) in a group of professional rugby players. Eleven male professional rugby players (age, 26 ± 3 years; height, ...

Leaf temperature and stomatal influences on sap velocity diurnal hysteresis in the Amazon rainforest

Science.gov (United States)

Jardine, K.; Gimenez, B.; Negron Juarez, R. I.; Koven, C.; Powell, T.; Higuchi, N.; Chambers, J.; Varadharajan, C.

2016-12-01

In order to improve our ability to predict terrestrial evapotranspiration fluxes, an understanding of the interactions between plant physiology and environmental conditions is necessary, but remains poorly characterized, especially in tropical ecosystems. In this study we show a tight positive correlation between sap velocity (at 1 m of height) and leaf surface temperature (LST, 20-30 m of height) in canopy dominant trees in two primary rainforest sites in the Amazon basin (Santarém and Manaus, Brazil). As leaf temperatures varied throughout the day, sap velocity responded with little delay (<15 min). Positive sap velocity was often observed at night, but also closely followed night time LSTs. When plotted versus LST, sap velocity showed an exponential increase before reaching a reflection point and a plateau and is characterized as a sigmoidal curve, in all observed trees. Moreover, a clear diurnal hysteresis in sap velocity was evident with morning periods showing higher temperature sensitivities than afternoon and night periods. Diurnal leaf observations showed a morning peak in stomatal conductance ( 10:00-10:30), but a mid-day to afternoon peak in transpiration and leaf temperature (12:00-14:00). Our observations suggest the sap velocity-LST hysteresis pattern arises due to the temporal offset between stomatal conductance and vapor pressure deficits (VPD) and demonstrates the dominating effect of VPD over stomatal conductance in maintaining high transpiration/sap flow rates under elevated temperatures. Our results have important implications for modeling tropical forest transpiration and suggests the possibility of predicting evapotranspiration fluxes at the ecosystem to regional scales based on remote sensed vegetation temperature.

The new double energy-velocity spectrometer VERDI

Science.gov (United States)

Jansson, Kaj; Frégeau, Marc Olivier; Al-Adili, Ali; Göök, Alf; Gustavsson, Cecilia; Hambsch, Franz-Josef; Oberstedt, Stephan; Pomp, Stephan

2017-09-01

VERDI (VElocity foR Direct particle Identification) is a fission-fragment spectrometer recently put into operation at JRC-Geel. It allows measuring the kinetic energy and velocity of both fission fragments simultaneously. The velocity provides information about the pre-neutron mass of each fission fragment when isotropic prompt-neutron emission from the fragments is assumed. The kinetic energy, in combination with the velocity, provides the post-neutron mass. From the difference between pre- and post-neutron masses, the number of neutrons emitted by each fragment can be determined. Multiplicity as a function of fragment mass and total kinetic energy is one important ingredient, essential for understanding the sharing of excitation energy between fission fragments at scission, and may be used to benchmark nuclear de-excitation models. The VERDI spectrometer design is a compromise between geometrical efficiency and mass resolution. The spectrometer consists of an electron detector located close to the target and two arrays of silicon detectors, each located 50 cm away from the target. In the present configuration pre-neutron and post-neutron mass distributions are in good agreement with reference data were obtained. Our latest measurements performed with spontaneously fissioning 252Cf is presented along with the developed calibration procedure to obtain pulse height defect and plasma delay time corrections.

Love and fear of heights: the pathophysiology and psychology of height imbalance.

Science.gov (United States)

Salassa, John R; Zapala, David A

2009-01-01

Individual psychological responses to heights vary on a continuum from acrophobia to height intolerance, height tolerance, and height enjoyment. This paper reviews the English literature and summarizes the physiologic and psychological factors that generate different responses to heights while standing still in a static or motionless environment. Perceptual cues to height arise from vision. Normal postural sway of 2 cm for peripheral objects within 3 m increases as eye-object distance increases. Postural sway >10 cm can result in a fall. A minimum of 20 minutes of peripheral retinal arc is required to detect motion. Trigonometry dictates that a 20-minute peripheral retinal arch can no longer be achieved in a standing position at an eye-object distance of >20 m. At this distance, visual cues conflict with somatosensory and vestibular inputs, resulting in variable degrees of imbalance. Co-occurring deficits in the visual, vestibular, and somatosensory systems can significantly increase height imbalance. An individual's psychological makeup, influenced by learned and genetic factors, can influence reactions to height imbalance. Enhancing peripheral vision and vestibular, proprioceptive, and haptic functions may improve height imbalance. Psychotherapy may improve the troubling subjective sensations to heights.

PROPERTIES OF BULGELESS DISK GALAXIES. II. STAR FORMATION AS A FUNCTION OF CIRCULAR VELOCITY

Energy Technology Data Exchange (ETDEWEB)

Watson, Linda C. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Martini, Paul; Wong, Man-Hong [Department of Astronomy, Ohio State University, 140 West 18th Avenue, Columbus, OH 43210 (United States); Lisenfeld, Ute [Departamento de Fisica Teorica y del Cosmos, Universidad de Granada, 18071 Granada (Spain); Boeker, Torsten [European Space Agency, Keplerlaan 1, 2200 AG Noordwijk (Netherlands); Schinnerer, Eva, E-mail: lwatson@cfa.harvard.edu [Max-Planck-Institut fuer Astronomie, Koenigstuhl 17, D-69117 Heidelberg (Germany)

2012-06-01

We study the relation between the surface density of gas and star formation rate in 20 moderately inclined, bulgeless disk galaxies (Sd-Sdm Hubble types) using CO(1-0) data from the IRAM 30 m telescope, H I emission line data from the VLA/EVLA, H{alpha} data from the MDM Observatory, and polycyclic aromatic hydrocarbon emission data derived from Spitzer IRAC observations. We specifically investigate the efficiency of star formation as a function of circular velocity (v{sub circ}). Previous work found that the vertical dust structure and disk stability of edge-on, bulgeless disk galaxies transition from diffuse dust lanes with large scale heights and gravitationally stable disks at v{sub circ} < 120 km s{sup -1} (M{sub *} {approx}< 10{sup 10} M{sub Sun }) to narrow dust lanes with small scale heights and gravitationally unstable disks at v{sub circ} > 120 km s{sup -1}. We find no transition in star formation efficiency ({Sigma}{sub SFR}/{Sigma}{sub Hi+H{sub 2}}) at v{sub circ} = 120 km s{sup -1} or at any other circular velocity probed by our sample (v{sub circ} = 46-190 km s{sup -1}). Contrary to previous work, we find no transition in disk stability at any circular velocity in our sample. Assuming our sample has the same dust structure transition as the edge-on sample, our results demonstrate that scale height differences in the cold interstellar medium of bulgeless disk galaxies do not significantly affect the molecular fraction or star formation efficiency. This may indicate that star formation is primarily affected by physical processes that act on smaller scales than the dust scale height, which lends support to local star formation models.

EVALUATION OF THE RE LATIONSHIP BETWEEN L EG STRENGTH AND VELOCITY VALUES IN AMATEUR FOOTBALL PLAYERS

Directory of Open Access Journals (Sweden)

İsmail G Ö K H A N

2015-08-01

Full Text Available The purpose of this study is to analyse the relationship between conditional parameters ( leg strength, back strength, velocity 30 Mt, flexibility by measuring some physical (height, body w eight and physiological (systole, diastole, KAH characteristics of male football players of Karakopru Belediyespor and Harran University. According to the results obtained from the measurements, mean age was 23, 46±3,50 /years; as a part of physical cha racteristics ,mean height was 176,20±5,10 (cm and mean body weight was 70,16±5,21 (kg . As a part of physiological characteristics, mean Systolic Blood Pressure was 123,87±14,23 (mmhg , mean Diastolic Blood Pressure was 73,60±16,42 (mmhg and mean Resting Heart Rate was 64,50±10,48 (beats/min . As a part of conditional parameters, mean leg strength was 101,83±40,48 (kg, back strength was 75,83±19,43 (kg, flexibility was 34,16±6,65 (cm and mean velocity in 30 Mt. was 4,15± 0,20 (sec. It was observed that there was a relationship between 30 meters velocity and leg strength parameters (r= - , 407 . There was no relationship between 30 meters velocity and back strength parameters (r=, 429; and between 30 meters velocity and flexibility param eters (r=, 659 . As a result, while the relationship between velocity and back strength values of the amateur football players was not significant (p>0.05 ; the relationship between velocity and leg strength values was found to be significant (p<0.05.

Should tsunami models use a nonzero initial condition for horizontal velocity?

Science.gov (United States)

Nava, G.; Lotto, G. C.; Dunham, E. M.

2017-12-01

Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require two initial conditions: one on sea surface height and another on depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). We run several full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor, using both idealized structures and a more realistic Tohoku structure. Substantial horizontal momentum is imparted to the ocean, but almost all momentum is carried away in the form of ocean acoustic waves. We compare tsunami propagation in each full-physics simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial conditions. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves (from ocean acoustic and seismic waves) at some final time, and backpropagating the tsunami

Effects of instability versus traditional resistance training on strength, power and velocity in untrained men.

Science.gov (United States)

Maté-Muñoz, José Luis; Monroy, Antonio J Antón; Jodra Jiménez, Pablo; Garnacho-Castaño, Manuel V

2014-09-01

The purpose of this study was compare the effects of a traditional and an instability resistance circuit training program on upper and lower limb strength, power, movement velocity and jumping ability. Thirty-six healthy untrained men were assigned to two experimental groups and a control group. Subjects in the experimental groups performed a resistance circuit training program consisting of traditional exercises (TRT, n = 10) or exercises executed in conditions of instability (using BOSU® and TRX®) (IRT, n = 12). Both programs involved three days per week of training for a total of seven weeks. The following variables were determined before and after training: maximal strength (1RM), average (AV) and peak velocity (PV), average (AP) and peak power (PP), all during bench press (BP) and back squat (BS) exercises, along with squat jump (SJ) height and counter movement jump (CMJ) height. All variables were found to significantly improve (p velocity and jumping ability. Key PointsSimilar adaptations in terms of gains in strength, power, movement velocity and jumping ability were produced in response to both training programs.Both the stability and instability approaches seem suitable for healthy, physically-active individuals with or with limited experience in resistance training.RPE emerged as a useful tool to monitor exercise intensity during instability strength training.

CRITICAL HEIGHT FOR THE DESTABILIZATION OF SOLAR PROMINENCES: STATISTICAL RESULTS FROM STEREO OBSERVATIONS

Energy Technology Data Exchange (ETDEWEB)

Liu Kai; Wang Yuming; Wang Shui; Shen Chenglong, E-mail: ymwang@ustc.edu.cn [CAS Key Laboratory of Geospace Environment, Department of Geophysics and Planetary Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2012-01-10

At which height is a prominence inclined to be unstable, or where is the most probable critical height for the prominence destabilization? This question was statistically studied based on 362 solar limb prominences well recognized by Solar Limb Prominence Catcher and Tracker from 2007 April to the end of 2009. We found that there are about 71% disrupted prominences (DPs), among which about 42% of them did not erupt successfully and about 89% of them experienced a sudden destabilization process. After a comprehensive analysis of the DPs, we discovered the following: (1) Most DPs become unstable at a height of 0.06-0.14 R{sub Sun} from the solar surface, and there are two most probable critical heights at which a prominence is very likely to become unstable, the first one is 0.13 R{sub Sun} and the second one is 0.19 R{sub Sun }. (2) An upper limit for the erupting velocity of eruptive prominences (EPs) exists, which decreases following a power law with increasing height and mass; accordingly, the kinetic energy of EPs has an upper limit too, which decreases as the critical height increases. (3) Stable prominences are generally longer and heavier than DPs, and not higher than 0.4 R{sub Sun }. (4) About 62% of the EPs were associated with coronal mass ejections (CMEs); but there is no difference in apparent properties between EPs associated with CMEs and those that are not.

CRITICAL HEIGHT FOR THE DESTABILIZATION OF SOLAR PROMINENCES: STATISTICAL RESULTS FROM STEREO OBSERVATIONS

International Nuclear Information System (INIS)

Liu Kai; Wang Yuming; Wang Shui; Shen Chenglong

2012-01-01

At which height is a prominence inclined to be unstable, or where is the most probable critical height for the prominence destabilization? This question was statistically studied based on 362 solar limb prominences well recognized by Solar Limb Prominence Catcher and Tracker from 2007 April to the end of 2009. We found that there are about 71% disrupted prominences (DPs), among which about 42% of them did not erupt successfully and about 89% of them experienced a sudden destabilization process. After a comprehensive analysis of the DPs, we discovered the following: (1) Most DPs become unstable at a height of 0.06-0.14 R ☉ from the solar surface, and there are two most probable critical heights at which a prominence is very likely to become unstable, the first one is 0.13 R ☉ and the second one is 0.19 R ☉ . (2) An upper limit for the erupting velocity of eruptive prominences (EPs) exists, which decreases following a power law with increasing height and mass; accordingly, the kinetic energy of EPs has an upper limit too, which decreases as the critical height increases. (3) Stable prominences are generally longer and heavier than DPs, and not higher than 0.4 R ☉ . (4) About 62% of the EPs were associated with coronal mass ejections (CMEs); but there is no difference in apparent properties between EPs associated with CMEs and those that are not.

DeepVel: Deep learning for the estimation of horizontal velocities at the solar surface

Science.gov (United States)

Asensio Ramos, A.; Requerey, I. S.; Vitas, N.

2017-07-01

Many phenomena taking place in the solar photosphere are controlled by plasma motions. Although the line-of-sight component of the velocity can be estimated using the Doppler effect, we do not have direct spectroscopic access to the components that are perpendicular to the line of sight. These components are typically estimated using methods based on local correlation tracking. We have designed DeepVel, an end-to-end deep neural network that produces an estimation of the velocity at every single pixel, every time step, and at three different heights in the atmosphere from just two consecutive continuum images. We confront DeepVel with local correlation tracking, pointing out that they give very similar results in the time and spatially averaged cases. We use the network to study the evolution in height of the horizontal velocity field in fragmenting granules, supporting the buoyancy-braking mechanism for the formation of integranular lanes in these granules. We also show that DeepVel can capture very small vortices, so that we can potentially expand the scaling cascade of vortices to very small sizes and durations. The movie attached to Fig. 3 is available at http://www.aanda.org

Effects of Instability Versus Traditional Resistance Training on Strength, Power and Velocity in Untrained Men

Directory of Open Access Journals (Sweden)

José Luis Maté-Muñoz

2014-09-01

Full Text Available The purpose of this study was compare the effects of a traditional and an instability resistance circuit training program on upper and lower limb strength, power, movement velocity and jumping ability. Thirty-six healthy untrained men were assigned to two experimental groups and a control group. Subjects in the experimental groups performed a resistance circuit training program consisting of traditional exercises (TRT, n = 10 or exercises executed in conditions of instability (using BOSU® and TRX® (IRT, n = 12. Both programs involved three days per week of training for a total of seven weeks. The following variables were determined before and after training: maximal strength (1RM, average (AV and peak velocity (PV, average (AP and peak power (PP, all during bench press (BP and back squat (BS exercises, along with squat jump (SJ height and counter movement jump (CMJ height. All variables were found to significantly improve (p <0.05 in response to both training programs. Major improvements were observed in SJ height (IRT = 22.1%, TRT = 20.1%, CMJ height (IRT = 17.7%, TRT = 15.2%, 1RM in BS (IRT = 13.03%, TRT = 12.6%, 1RM in BP (IRT = 4.7%, TRT = 4.4%, AP in BS (IRT = 10.5%, TRT = 9.3%, AP in BP (IRT = 2.4%, TRT = 8.1%, PP in BS (IRT=19.42%, TRT = 22.3%, PP in BP (IRT = 7.6%, TRT = 11.5%, AV in BS (IRT = 10.5%, TRT = 9.4%, and PV in BS (IRT = 8.6%, TRT = 4.5%. Despite such improvements no significant differences were detected in the posttraining variables recorded for the two experimental groups. These data indicate that a circuit training program using two instability training devices is as effective in untrained men as a program executed under stable conditions for improving strength (1RM, power, movement velocity and jumping ability.

Agreement between measured height, and height predicted from ...

African Journals Online (AJOL)

lower limb measurements, such as knee height, as well as upper limb measures ... had with bone injuries/fractures affecting height or ulna length; and n = 1 had a ... and heels, buttocks and upper back in contact with the vertical surface of the .... found striking similarity in linear growth of infants to five-year- olds among all ...

Accuracy of recumbent height measurement.

Science.gov (United States)

Gray, D S; Crider, J B; Kelley, C; Dickinson, L C

1985-01-01

Since many patients requiring specialized nutritional support are bedridden, measurement of height for purposes of nutritional assessment or prescription must often be done with the patient in bed. This study examined the accuracy of measuring body height in bed in the supine position. Two measurements were performed on 108 ambulatory inpatients: (1) standing height using a standard height-weight scale, and (2) bed height using a flexible tape. Patients were divided into four groups based on which of two researchers performed each of the two measurements. Each patient was also weighed and self-reported height, weight, sex, and age were recorded. Bed height was significantly longer than standing height by 3.68 cm, but the two measurements were equally precise. It was believed, however, that this 2% difference was probably not clinically significant in most circumstances. Bed height correlated highly with standing height (r = 0.95), and the regression equation was standing height = 13.82 +/- 0.09 bed height. Patients overestimated their heights. Heights recorded by nurses were more accurate when patients were measured than when asked about their heights, but the patients were more often asked than measured.

Development and Validity of a Scale of Perception of Velocity in Resistance Exercise

OpenAIRE

Bautista, Iker J.; Chirosa, Ignacio J.; Chirosa, Luis J.; Martín, Ignacio; González, Andrés; Robertson, Robert J.

2014-01-01

This aims of this study were twofold; 1) to development a new scale of perceived velocity in the bench press exercise and 2) to examine the scales concurrent validity. Twenty one physically active males with mean ±SD age, height and weights of: 27.5 ± 4.7 years, 1.77 ± 0.07 m, and 79.8 ± 10.3 kg respectively, took part in the study. The criterion variable used to test the validity of the new scale was the mean execution velocity (Velreal) of the bench press exercise. Three intensities (light ...

The Relationship Between Maximum Isometric Strength and Ball Velocity in the Tennis Serve.

Science.gov (United States)

Baiget, Ernest; Corbi, Francisco; Fuentes, Juan Pedro; Fernández-Fernández, Jaime

2016-12-01

The aims of this study were to analyze the relationship between maximum isometric strength levels in different upper and lower limb joints and serve velocity in competitive tennis players as well as to develop a prediction model based on this information. Twelve male competitive tennis players (mean ± SD; age: 17.2 ± 1.0 years; body height: 180.1 ± 6.2 cm; body mass: 71.9 ± 5.6 kg) were tested using maximum isometric strength levels (i.e., wrist, elbow and shoulder flexion and extension; leg and back extension; shoulder external and internal rotation). Serve velocity was measured using a radar gun. Results showed a strong positive relationship between serve velocity and shoulder internal rotation (r = 0.67; p isometric strength level in shoulder internal rotation was strongly related to serve velocity, and a large part of the variability in serve velocity was explained by the maximum isometric strength levels in shoulder internal rotation and shoulder flexion.

Rate effects on timing, key velocity, and finger kinematics in piano performance.

Science.gov (United States)

Bella, Simone Dalla; Palmer, Caroline

2011-01-01

We examined the effect of rate on finger kinematics in goal-directed actions of pianists. In addition, we evaluated whether movement kinematics can be treated as an indicator of personal identity. Pianists' finger movements were recorded with a motion capture system while they performed melodies from memory at different rates. Pianists' peak finger heights above the keys preceding keystrokes increased as tempo increased, and were attained about one tone before keypress. These rate effects were not simply due to a strategy to increase key velocity (associated with tone intensity) of the corresponding keystroke. Greater finger heights may compensate via greater tactile feedback for a speed-accuracy tradeoff that underlies the tendency toward larger temporal variability at faster tempi. This would allow pianists to maintain high temporal accuracy when playing at fast rates. In addition, finger velocity and accelerations as pianists' fingers approached keys were sufficiently unique to allow pianists' identification with a neural-network classifier. Classification success was higher in pianists with more extensive musical training. Pianists' movement "signatures" may reflect unique goal-directed movement kinematic patterns, leading to individualistic sound.

Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis.

Science.gov (United States)

Knijnenburg, S L; Raemaekers, S; van den Berg, H; van Dijk, I W E M; Lieverst, J A; van der Pal, H J; Jaspers, M W M; Caron, H N; Kremer, L C; van Santen, H M

2013-04-01

Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of 573 CCS. Multivariable regression analyses were carried out to estimate the influence of different determinants on height SDS at follow-up. Overall, survivors had a normal height SDS at cancer diagnosis. However, at follow-up in adulthood, 8.9% had a height ≤-2 SDS. Height SDS at diagnosis was an important determinant for adult height SDS. Children treated with (higher doses of) radiotherapy showed significantly reduced final height SDS. Survivors treated with total body irradiation (TBI) and craniospinal radiation had the greatest loss in height (-1.56 and -1.37 SDS, respectively). Younger age at diagnosis contributed negatively to final height. Height at diagnosis was an important determinant for height SDS at follow-up. Survivors treated with TBI, cranial and craniospinal irradiation should be monitored periodically for adequate linear growth, to enable treatment on time if necessary. For correct interpretation of treatment-related late effects studies in CCS, pre-treatment data should always be included.

Effects of Instability Versus Traditional Resistance Training on Strength, Power and Velocity in Untrained Men

Science.gov (United States)

Maté-Muñoz, José Luis; Monroy, Antonio J. Antón; Jodra Jiménez, Pablo; Garnacho-Castaño, Manuel V.

2014-01-01

The purpose of this study was compare the effects of a traditional and an instability resistance circuit training program on upper and lower limb strength, power, movement velocity and jumping ability. Thirty-six healthy untrained men were assigned to two experimental groups and a control group. Subjects in the experimental groups performed a resistance circuit training program consisting of traditional exercises (TRT, n = 10) or exercises executed in conditions of instability (using BOSU® and TRX®) (IRT, n = 12). Both programs involved three days per week of training for a total of seven weeks. The following variables were determined before and after training: maximal strength (1RM), average (AV) and peak velocity (PV), average (AP) and peak power (PP), all during bench press (BP) and back squat (BS) exercises, along with squat jump (SJ) height and counter movement jump (CMJ) height. All variables were found to significantly improve (p <0.05) in response to both training programs. Major improvements were observed in SJ height (IRT = 22.1%, TRT = 20.1%), CMJ height (IRT = 17.7%, TRT = 15.2%), 1RM in BS (IRT = 13.03%, TRT = 12.6%), 1RM in BP (IRT = 4.7%, TRT = 4.4%), AP in BS (IRT = 10.5%, TRT = 9.3%), AP in BP (IRT = 2.4%, TRT = 8.1%), PP in BS (IRT=19.42%, TRT = 22.3%), PP in BP (IRT = 7.6%, TRT = 11.5%), AV in BS (IRT = 10.5%, TRT = 9.4%), and PV in BS (IRT = 8.6%, TRT = 4.5%). Despite such improvements no significant differences were detected in the posttraining variables recorded for the two experimental groups. These data indicate that a circuit training program using two instability training devices is as effective in untrained men as a program executed under stable conditions for improving strength (1RM), power, movement velocity and jumping ability. Key Points Similar adaptations in terms of gains in strength, power, movement velocity and jumping ability were produced in response to both training programs. Both the stability and instability approaches

Differences in physical fitness and throwing velocity among elite and amateur male handball players.

Science.gov (United States)

Gorostiaga, E M; Granados, C; Ibáñez, J; Izquierdo, M

2005-04-01

This study compared physical characteristics (body height, body mass [BM], body fat [BF], and free fatty mass [FFM]), one repetition maximum bench-press (1RM (BP)), jumping explosive strength (VJ), handball throwing velocity, power-load relationship of the leg and arm extensor muscles, 5- and 15-m sprint running time, and running endurance in two handball male teams: elite team, one of the world's leading teams (EM, n = 15) and amateur team, playing in the Spanish National Second Division (AM, n = 15). EM had similar values in body height, BF, VJ, 5- and 15-m sprint running time and running endurance than AM. However, the EM group gave higher values in BM (95.2 +/- 13 kg vs. 82.4 +/- 10 kg, p vs. 72.4 +/- 7 kg, p vs. 83 +/- 10 kg, p vs. 21.8 +/- 1.6 m . s (-1), p vs. 22.9 +/- 1.4 m . s (-1), p individual values of velocity at 30 % of 1RM (BP) and individual values of ball velocity during a standing throw. Significant correlations were observed in EM, but not in AM, between the individual values of velocity during 3-step running throw and the individual values of velocity at 30 % of 1RM (BP) (r = 0.72, p individual values of power at 100 % of body mass during half-squat actions (r = 0.62, p < 0.05). The present results suggest that more muscular and powerful players are at an advantage in handball. The differences observed in free fatty mass could partly explain the differences observed between groups in absolute maximal strength and muscle power. In EM, higher efficiency in handball throwing velocity may be associated with both upper and lower extremity power output capabilities, whereas in AM this relationship may be different. Endurance capacity does not seem to represent a limitation for elite performance in handball.

Study of natural convection heat transfer characteristics. (1) Influence of ventilation duct height

International Nuclear Information System (INIS)

Wakamatsu, Mitsuo; Iwaki, Chikako; Ikeda, Tatsumi; Morooka, Shinichi; Ikeda, Hiroshi; Nakada, Kotaro; Masaki, Yoshikazu

2008-01-01

Natural cooling system has been investigated in waste storage. It is important to evaluate the flow by natural draft enough to removal the decay heat from the waste. In this study, we carried out the fundamental experiment of ventilation duct height effect for natural convection on vertical cylindrical heater in atmospheric air. The scale of test facility is about 4m height with single heater. The heating value is varied in the range of 33-110W, where Rayleigh number is over 10 10 . Natural convection flow rate were calculated by measured velocity with thermo anemometer in the inlet duct. The temperature of the cylindrical heater wall and fluid were measured with thermocouples. It was found that the heat transfer coefficient difference between long duct and short duct is small in this experiment. (author)

Validity of Hip-worn Inertial Measurement Unit Compared to Jump Mat for Jump Height Measurement in Adolescents.

Science.gov (United States)

Rantalainen, T; Hesketh, K D; Rodda, C; Duckham, R L

2018-06-16

Jump tests assess lower body power production capacity, and can be used to evaluate athletic ability and development during growth. Wearable inertial measurement units (IMU) seem to offer a feasible alternative to laboratory-based equipment for jump height assessments. Concurrent validity of these devices for jump height assessments has only been established in adults. Therefore, the purpose of this study was to evaluate the concurrent validity of IMU-based jump height estimate compared to contact mat-based jump height estimate in adolescents. Ninety-five adolescents (10-13 years-of-age; girls N=41, height = 154 (SD 9) cm, weight = 44 (11) kg; boys N=54, height=156 (10) cm, weight = 46 (13) kg) completed three counter-movement jumps for maximal jump height on a contact mat. Inertial recordings (accelerations, rotations) were concurrently recorded with a hip-worn IMU (sampling at 256 Hz). Jump height was evaluated based on flight time. The mean IMU-derived jump height was 27.1 (SD 3.8) cm, and the corresponding mean jump-mat-derived value was 21.5 (3.4) cm. While a significant 26% mean difference was observed between the methods (5.5 [95% limits of agreement 2.2 to 8.9] cm, p = 0.006), the correspondence between methods was excellent (ICC = 0.89). The difference between methods was weakly positively associated with jump height (r = 0.28, P = 0.007). Take-off velocity derived jump height was also explored but produced only fair congruence. In conclusion, IMU-derived jump height exhibited excellent congruence to contact mat-based jump height and therefore presents a feasible alternative for jump height assessments in adolescents. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Social inequalities in height: persisting differences today depend upon height of the parents.

Directory of Open Access Journals (Sweden)

Bruna Galobardes

Full Text Available Substantial increases in height have occurred concurrently with economic development in most populations during the last century. In high-income countries, environmental exposures that can limit genetic growth potential appear to have lessened, and variation in height by socioeconomic position may have diminished. The objective of this study is to investigate inequalities in height in a cohort of children born in the early 1990s in England, and to evaluate which factors might explain any identified inequalities.12,830 children from The Avon Longitudinal Study of Parents and Children (ALSPAC, a population based cohort from birth to about 11.5 years of age, were used in this analysis. Gender- and age-specific z-scores of height at different ages were used as outcome variables. Multilevel models were used to take into account the repeated measures of height and to analyze gender- and age-specific relative changes in height from birth to 11.5 years. Maternal education was the main exposure variable used to examine socioeconomic inequalities. The roles of parental and family characteristics in explaining any observed differences between maternal education and child height were investigated. Children whose mothers had the highest education compared to those with none or a basic level of education, were 0.39 cm longer at birth (95% CI: 0.30 to 0.48. These differences persisted and at 11.5 years the height difference was 1.4 cm (95% CI: 1.07 to 1.74. Several other factors were related to offspring height, but few changed the relationship with maternal education. The one exception was mid-parental height, which fully accounted for the maternal educational differences in offspring height.In a cohort of children born in the 1990s, mothers with higher education gave birth to taller boys and girls. Although height differences were small they persisted throughout childhood. Maternal and paternal height fully explained these differences.

Neutron Star Population Dynamics. II. Three-dimensional Space Velocities of Young Pulsars

Science.gov (United States)

Cordes, J. M.; Chernoff, David F.

1998-09-01

We use astrometric, distance, and spindown data on pulsars to (1) estimate three-dimensional velocity components, birth distances from the Galactic plane, and ages of individual objects; (2) determine the distribution of space velocities and the scale height of pulsar progenitors; (3) test spindown laws for pulsars; (4) test for correlations between space velocities and other pulsar parameters; and (5) place empirical requirements on mechanisms than can produce high-velocity neutron stars. Our approach incorporates measurement errors, uncertainties in distances, deceleration in the Galactic potential, and differential Galactic rotation. We focus on a sample of proper motion measurements of young (case-by-case basis assuming that the actual age equals the conventional spindown age for a braking index n = 3, no torque decay, and birth periods much shorter than present-day periods. Every sample member could have originated within 0.3 kpc of the Galactic plane while still having reasonable present-day peculiar radial velocities. For the 49 object sample, the scale height of the progenitors is ~0.13 kpc, and the three-dimensional velocities are distributed in two components with characteristic speeds of 175+19-24 km s-1 and 700+300-132 km s-1, representing ~86% and ~14% of the population, respectively. The sample velocities are inconsistent with a single-component Gaussian model and are well described by a two-component Gaussian model but do not require models of additional complexity. From the best-fit distribution, we estimate that about 20% of the known pulsars will escape the Galaxy, assuming an escape speed of 500 km s-1. The best-fit, dual-component model, if augmented by an additional, low-velocity (The best three-component models do not show a preference for filling in the probability distribution at speeds intermediate to 175 and 700 km s-1 but are nearly degenerate with the best two-component models. We estimate that the high-velocity tail (>1000 km s-1) may

The Numerical Study on the Influence of Prandtl Number and Height of the Enclosure

International Nuclear Information System (INIS)

Moon, Je-Young; Chung, Bum-Jin

2016-01-01

This study investigated numerically the internal flow depending on Prandtl number of fluid and height of enclosure. The two-dimensional numerical simulations were performed for several heights of enclosure in the range between 0.01 m and 0.074 m. It corresponds to the aspect ratio (H/L) ranged from 0.07 to 0.5. Prandtl number was 0.2, 0.7 and 7. Rayleigh number based on the height of enclosure ranged between 8.49x10 3 and 1.20x10 8 . The numerical calculations were carried out using FLUENT 6.3. In order to confirm the influence of Prandtl number and height of side walls on the internal flow and heat transfer of the horizontal enclosure, the numerical study is carried out using the FLUENT 6.3. The numerical results for the condition of top cooling only agree well with Rayleigh-Benard natural convection. When the top and side walls were cooled, the internal flow of enclosure is more complex. The thickness of thermal and velocity boundary layer varies with Prandtl number. For Pr>1 the behavior of cells is unstable and irregular owing to the entrained plume, whereas the internal flow for Pr<1 is stable and regular. Also, the number of cells increases depending on decrease of height. As a result, the heat exchange increases

Modeling of velocity field for vacuum induction melting process

Institute of Scientific and Technical Information of China (English)

CHEN Bo; JIANG Zhi-guo; LIU Kui; LI Yi-yi

2005-01-01

The numerical simulation for the recirculating flow of melting of an electromagnetically stirred alloy in a cylindrical induction furnace crucible was presented. Inductive currents and electromagnetic body forces in the alloy under three different solenoid frequencies and three different melting powers were calculated, and then the forces were adopted in the fluid flow equations to simulate the flow of the alloy and the behavior of the free surface. The relationship between the height of the electromagnetic stirring meniscus, melting power, and solenoid frequency was derived based on the law of mass conservation. The results show that the inductive currents and the electromagnetic forces vary with the frequency, melting power, and the physical properties of metal. The velocity and the height of the meniscus increase with the increase of the melting power and the decrease of the solenoid frequency.

A study of acoustic halos in active region NOAA 11330 using multi-height SDO observations

Science.gov (United States)

Tripathy, S. C.; Jain, K.; Kholikov, S.; Hill, F.; Rajaguru, S. P.; Cally, P. S.

2018-01-01

We analyze data from the Helioseismic Magnetic Imager (HMI) and the Atmospheric Imaging Assembly (AIA) instruments on board the Solar Dynamics Observatory (SDO) to characterize the spatio-temporal acoustic power distribution in active regions as a function of the height in the solar atmosphere. For this, we use Doppler velocity and continuum intensity observed using the magnetically sensitive line at 6173 Å as well as intensity at 1600 Å and 1700 Å. We focus on the power enhancements seen around AR 11330 as a function of wave frequency, magnetic field strength, field inclination and observation height. We find that acoustic halos occur above the acoustic cutoff frequency and extends up to 10 mHz in HMI Doppler and AIA 1700 Å observations. Halos are also found to be strong functions of magnetic field and their inclination angle. We further calculate and examine the spatially averaged relative phases and cross-coherence spectra and find different wave characteristics at different heights.

Influence of fall height on high impact polystyrene deformation and characteristics of drop weight test

Directory of Open Access Journals (Sweden)

Mizera Ales

2017-01-01

Full Text Available This study deals with high impact polystyrene (HIPS which was subjected the drop-weight test. HIPS is a polymer produced by the reaction between butadiene synthetic elastomer and styrene (5–14 % which contains the crystal polymer in certain amounts and is commonly used in mechanical engineering applications where machine parts are exposed to impact loading. The injection moulded HIPS samples were subjected the penetration test at different fall heights and the results were subsequently evaluated and discussed. It was found out that all fall heights are suitable for HIPS penetration, but the optimal one is 50 J because of the smallest variation range. Higher heights are not needed because of increasing power consumption of the test device. From the results, it is clear, that HIPS is not so highly impact resistant material as for example HDPE, because of that is this material suitable for applications where is not often exposed to too big impacts at high velocities.

Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis

NARCIS (Netherlands)

Knijnenburg, S. L.; Raemaekers, S.; van den Berg, H.; van Dijk, I. W. E. M.; Lieverst, J. A.; van der Pal, H. J.; Jaspers, M. W. M.; Caron, H. N.; Kremer, L. C.; van Santen, H. M.

2013-01-01

Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of

Do Assimilated Drifter Velocities Improve Lagrangian Predictability in an Operational Ocean Model?

Science.gov (United States)

2015-05-01

extended Kalman filter . Molcard et al. (2005) used a statistical method to cor- relate model and drifter velocities. Taillandier et al. (2006) describe the... temperature and salinity observations. Trajectory angular differ- ences are also reduced. 1. Introduction The importance of Lagrangian forecasts was seen... Temperature , salinity, and sea surface height (SSH, measured along-track by satellite altimeters) observa- tions are typically assimilated in

Height premium for job performance.

Science.gov (United States)

Kim, Tae Hyun; Han, Euna

2017-08-01

This study assessed the relationship of height with wages, using the 1998 and 2012 Korean Labor and Income Panel Study data. The key independent variable was height measured in centimeters, which was included as a series of dummy indicators of height per 5cm span (wages to assess the heterogeneity in the height-wage relationship, across the conditional distribution of monthly wages. We found a non-linear relationship of height with monthly wages. For men, the magnitude of the height wage premium was overall larger at the upper quantile of the conditional distribution of log monthly wages than at the median to low quantile, particularly in professional and semi-professional occupations. The height-wage premium was also larger at the 90th quantile for self-employed women and salaried men. Our findings add a global dimension to the existing evidence on height-wage premium, demonstrating non-linearity in the association between height and wages and heterogeneous changes in the dispersion and direction of the association between height and wages, by wage level. Copyright © 2017 Elsevier B.V. All rights reserved.

Diffuse Ceiling Ventilation and the Influence of Room Height and Heat Load Distribution

DEFF Research Database (Denmark)

Nielsen, Peter Vilhelm; Vilsbøll, Rasmus W; Liu, Li

2015-01-01

Diffuse ceiling (inlet) ventilation is an air distribution system that supplies air from the entire ceiling surface, giving a low supply velocity. The flow pattern in the room is controlled by the heat sources. The system generates high mixing flow and the air velocities in the room are expected...... to be not much influenced by the flow rate to the room but dependent on the heat load. Previous studies have shown that diffuse ceiling ventilation has an ability to remove large heat loads without compromising the indoor climate. However, recent experiments indicate that the maximum accepted heat load decreases...... with a large room height and it decreases in connection with certain heat load distributions. Room geometries and heat load distributions that are optimal for diffuse ceiling ventilation are discussed. A simplified design procedure is introduced....

The effect of step height on the performance of three-dimensional ac electro-osmotic microfluidic pumps.

Science.gov (United States)

Urbanski, John Paul; Levitan, Jeremy A; Burch, Damian N; Thorsen, Todd; Bazant, Martin Z

2007-05-15

Recent numerical and experimental studies have investigated the increase in efficiency of microfluidic ac electro-osmotic pumps by introducing nonplanar geometries with raised steps on the electrodes. In this study, we analyze the effect of the step height on ac electro-osmotic pump performance. AC electro-osmotic pumps with three-dimensional electroplated steps are fabricated on glass substrates and pumping velocities of low ionic strength electrolyte solutions are measured systematically using a custom microfluidic device. Numerical simulations predict an improvement in pump performance with increasing step height, at a given frequency and voltage, up to an optimal step height, which qualitatively matches the trend observed in experiment. For a broad range of step heights near the optimum, the observed flow is much faster than with existing planar pumps (at the same voltage and minimum feature size) and in the theoretically predicted direction of the "fluid conveyor belt" mechanism. For small step heights, the experiments also exhibit significant flow reversal at the optimal frequency, which cannot be explained by the theory, although the simulations predict weak flow reversal at higher frequencies due to incomplete charging. These results provide insight to an important parameter for the design of nonplanar electro-osmotic pumps and clues to improve the fundamental theory of ACEO.

Rate effects on timing, key velocity, and finger kinematics in piano performance.

Directory of Open Access Journals (Sweden)

Simone Dalla Bella

Full Text Available We examined the effect of rate on finger kinematics in goal-directed actions of pianists. In addition, we evaluated whether movement kinematics can be treated as an indicator of personal identity. Pianists' finger movements were recorded with a motion capture system while they performed melodies from memory at different rates. Pianists' peak finger heights above the keys preceding keystrokes increased as tempo increased, and were attained about one tone before keypress. These rate effects were not simply due to a strategy to increase key velocity (associated with tone intensity of the corresponding keystroke. Greater finger heights may compensate via greater tactile feedback for a speed-accuracy tradeoff that underlies the tendency toward larger temporal variability at faster tempi. This would allow pianists to maintain high temporal accuracy when playing at fast rates. In addition, finger velocity and accelerations as pianists' fingers approached keys were sufficiently unique to allow pianists' identification with a neural-network classifier. Classification success was higher in pianists with more extensive musical training. Pianists' movement "signatures" may reflect unique goal-directed movement kinematic patterns, leading to individualistic sound.

Height-Deterministic Pushdown Automata

DEFF Research Database (Denmark)

Nowotka, Dirk; Srba, Jiri

2007-01-01

We define the notion of height-deterministic pushdown automata, a model where for any given input string the stack heights during any (nondeterministic) computation on the input are a priori fixed. Different subclasses of height-deterministic pushdown automata, strictly containing the class...... of regular languages and still closed under boolean language operations, are considered. Several of such language classes have been described in the literature. Here, we suggest a natural and intuitive model that subsumes all the formalisms proposed so far by employing height-deterministic pushdown automata...

Study on lumbar kinematics and the risk of low back disorder in female university students by using shoes of different heel heights.

Science.gov (United States)

Iqbal, Rauf; De, Amitabha; Mishra, Wricha; Maulik, Shreya; Chandra, A M

2012-01-01

The study was taken up to investigate the effects of heel heights on lumbar kinematics and the risk of Low Back Disorder (LBD) in females. Nineteen female university students (24.5 ± 3.36 yrs) volunteered in the study. Lumbar kinematics was measured by using Industrial Lumbar Motion Monitor (iLMM). The volunteers were asked to walk for a distance of 50 meters in 3 different given conditions i.e bare foot (Heel 0), with flat heels (Heel 1) and with high heels (Heel 2). Heights of Heel 1 and Heel 2 were 1.5 ± 0.84 cm and 5.5 ± 1.70 cm respectively. The Lumbar kinematic parameters studied were- Average Twisting Velocity (ATV), Maximum Sagital Flexion (MSF) and Maximum Lateral Velocity (MLV). It was observed that all the above mentioned Lumbar kinematics - ATV, MSF and MLV increases with increase of heel heights, which in turn increases the risk of LBD. As a result of increase in Lumbar kinematic values with increase in heel heights, LBD risk has also increased. Mean and SD of the LBD risk with Heel 0, Heel 1 and Heel 2 were 16.79 ± 6.04%, 19.00 ± 7.38% and 22.11 ± 6.98% respectively. Lower stature with high heels showed higher risk of LBD than the higher stature with high heels.

Interpreting Power-Force-Velocity Profiles for Individualized and Specific Training.

Science.gov (United States)

Morin, Jean-Benoît; Samozino, Pierre

2016-03-01

Recent studies have brought new insights into the evaluation of power-force-velocity profiles in both ballistic push-offs (eg, jumps) and sprint movements. These are major physical components of performance in many sports, and the methods the authors developed and validated are based on data that are now rather simple to obtain in field conditions (eg, body mass, jump height, sprint times, or velocity). The promising aspect of these approaches is that they allow for more individualized and accurate evaluation, monitoring, and training practices, the success of which is highly dependent on the correct collection, generation, and interpretation of athletes' mechanical outputs. The authors therefore wanted to provide a practical vade mecum to sports practitioners interested in implementing these power-force-velocity-profiling approaches. After providing a summary of theoretical and practical definitions for the main variables, the authors first detail how vertical profiling can be used to manage ballistic push-off performance, with emphasis on the concept of optimal force-velocity profile and the associated force-velocity imbalance. Furthermore, they discuss these same concepts with regard to horizontal profiling in the management of sprinting performance. These sections are illustrated by typical examples from the authors' practice. Finally, they provide a practical and operational synthesis and outline future challenges that will help further develop these approaches.

Experimental determination of deflagration velocity and blue cone height for natural gases from Guajira and Cusiana

International Nuclear Information System (INIS)

Fernandez Martinez, Alejandro; Piza Molina, Carlos Andres; Vanegas Jaramillo, Gilmar Adoni

2001-01-01

In this project the conical flame method was implemented to measure deflagration rate and a direct photography method to measure the height of blue cone for to natural gases with Guajira and Cusiana composition. Besides of these the existent relation between both variables was determined. The information obtained in this work is fundamental, as long as it provides an experimental method that applied to real conditions, allows the characterization of the natural gases of Guajira and Cusiana, witch will be of utility to define criterions of de sing and interchange ability in the commercial and industrial combustion systems

Jumping Abilities and Power-Velocity Relationship in Judo Athletes: Comparative Analysis Among Age Categories

Directory of Open Access Journals (Sweden)

Buśko Krzysztof

2015-06-01

Full Text Available Purpose. The aim of the study was to examine age differences in the maximal power and height of rise of the body mass centre measured in spike jump (SPJ and counter-movement jump (CMJ, and power-velocity relationship of lower extremities between cadet and U23 age class judo athletes. Methods. Seven cadets (age 16.6 ± 0.7 years and eight U23 age class (21.3 ± 1.4 years Polish judoists took part in the study. The maximal power and height of jump were measured at SPJ and CMJ jumps. Power- velocity relations (P-v were determined from 5 maximal cycle ergometer exercise bouts at increasing external loads equal to 2.5, 5.0, 7.5, 10.0 and 12.5% of body weight (BW. Results. Cadet judoists had a significantly smaller maximal power output (11.56 ± 1.21 W ・ kg-1 than U23 athletes (12.69 ± 0.67 W ・ kg-1. The optimal velocity was similar in both group (119.3 ± 16.0 rpm and 119.6 ± 15.5 rpm, respectively. Significant age differences were founded between the cadet and U23 athletes for power output at external load equal 12.5% BW. Cadet judoists generated insignificantly lower maximal power in CMJ and SPJ than U23 judo athletes with except of the absolute maximal power in SPJ. The age difference was observed in height of CMJ. Conclusions. Based on the characteristics of F-v curve we can see in which direction follow the effects of training. Application of CMJ and SPJ in jumping test allows to assess changes in neuromuscular coordination. The use of the both methods give better information to optimal training control.

The role of intrinsic muscle properties for stable hopping-stability is achieved by the force-velocity relation

International Nuclear Information System (INIS)

Haeufle, D F B; Grimmer, S; Seyfarth, A

2010-01-01

A reductionist approach was presented to investigate which level of detail of the physiological muscle is required for stable locomotion. Periodic movements of a simplified one-dimensional hopping model with a Hill-type muscle (one contractile element, neither serial nor parallel elastic elements) were analyzed. Force-length and force-velocity relations of the muscle were varied in three levels of approximation (constant, linear and Hill-shaped nonlinear) resulting in nine different hopping models of different complexity. Stability of these models was evaluated by return map analysis and the performance by the maximum hopping height. The simplest model (constant force-length and constant force-velocity relations) outperformed all others in the maximum hopping height but was unstable. Stable hopping was achieved with linear and Hill-shaped nonlinear characteristic of the force-velocity relation. The characteristics of the force-length relation marginally influenced hopping stability. The results of this approach indicate that the intrinsic properties of the contractile element are responsible for stabilization of periodic movements. This connotes that (a) complex movements like legged locomotion could benefit from stabilizing effects of muscle properties, and (b) technical systems could benefit from the emerging stability when implementing biological characteristics into artificial muscles.

Using IR Imaging of Water Surfaces for Estimating Piston Velocities

Science.gov (United States)

Gålfalk, M.; Bastviken, D.; Arneborg, L.

2013-12-01

The transport of gasses dissolved in surface waters across the water-atmosphere interface is controlled by the piston velocity (k). This coefficient has large implications for, e.g., greenhouse gas fluxes but is challenging to quantify in situ. At present, empirical k-wind speed relationships from a small number of studies and systems are often extrapolated without knowledge of model performance. It is therefore of interest to search for new methods for estimating k, and to compare the pros and cons of existing and new methods. Wind speeds in such models are often measured at a height of 10 meters. In smaller bodies of water such as lakes, wind speeds can vary dramatically across the surface through varying degrees of wind shadow from e.g. trees at the shoreline. More local measurements of the water surface, through wave heights or surface motion mapping, could give improved k-estimates over a surface, also taking into account wind fetch. At thermal infrared (IR) wavelengths water has very low reflectivity (depending on viewing angle) than can go below 1%, meaning that more than 99% is heat radiation giving a direct measurement of surface temperature variations. Using an IR camera at about 100 frames/s one could map surface temperature structures at a fraction of a mm depth even with waves present. In this presentation I will focus on IR imaging as a possible tool for estimating piston velocities. Results will be presented from IR field measurements, relating the motions of surface temperature structures to k calculated from other simultaneous measurements (flux chamber and ADV-Based Dissipation Rate), but also attempting to calculate k directly from the IR surface divergence. A relation between wave height and k will also be presented.

The Relationship between Repeated Sprint Performance and Velocity Values during Loaded-Squat Jump Exercise

Science.gov (United States)

Can, Ibrahim; Sadik, Seda; Bayrakdaroglu, Serdar

2018-01-01

The purpose of this study is to investigate the relationship between repeated sprint performance and velocity values during loaded-squat jump exercise. In accordance with this purpose, 23 kickboxing athletes (age: 21,1 ± 2,10 years; height: 178,7 ± 5,01 cm; weight: 70,8 ± 7,85 kg) participated voluntarily in this study. Participants were performed…

Unified height systems after GOCE

Science.gov (United States)

Rummel, Reiner; Gruber, Thomas; Sideris, Michael; Rangelova, Elena; Woodworth, Phil; Hughes, Chris; Ihde, Johannes; Liebsch, Gunter; Rülke, Axel; Gerlach, Christian; Haagmans, Roger

2015-04-01

The objectives of global height unification are twofold, (1) the realization of accurate geopotential numbers C together with their standard deviation σ(C) at a selected set of stations (datum points of national height systems, geodetic fundamental stations (IERS), primary tide gauges (PSMSL) and primary reference clocks (IERS)) and (2) the determination of height off-sets between all existing regional/national height systems and one global height reference. In the future the primary method of height determination will be GPS-levelling with very stringent requirements concerning the consistency of the positioning and the gravity potential difference part. Consistency is required in terms of the applied standards (ITRF, zero tide system, geodetic reference system). Geopotential differences will be based on a next generation geopotential model combining GOCE and GRACE and a best possible collection of global terrestrial and altimetric gravity and topographic data. Ultimately, the envisaged accuracy of height unification is about 10 cm2/s2 (or 1cm). At the moment, in well surveyed regions, an accuracy of about 40 to 60 cm2/s2 (or 4 to 6cm) is attainable. Objective One can be realized by straight forward computation of geopotential numbers C, i.e. geopotential differences relative to an adopted height reference. No adjustment is required for this. Objective Two, the unification of existing height systems is achieved by employing a least-squares adjustment based on the GBVP-approach. In order to attain a non-singular solution, this requires for each included datum zone at least one geo-referenced station per zone, i.e. its ellipsoidal height h and, in addition, the corresponding physical height H (geopotential number, normal height, orthometric height, etc.). Changes in geopotential numbers of consecutive realizations reflect (1) temporal changes of station heights, (2) improvements or changes of the applied geopotential (or geoid) model and (3) improvements of the

Global effects of income and income inequality on adult height and sexual dimorphism in height.

Science.gov (United States)

Bogin, Barry; Scheffler, Christiane; Hermanussen, Michael

2017-03-01

Average adult height of a population is considered a biomarker of the quality of the health environment and economic conditions. The causal relationships between height and income inequality are not well understood. We analyze data from 169 countries for national average heights of men and women and national-level economic factors to test two hypotheses: (1) income inequality has a greater association with average adult height than does absolute income; and (2) neither income nor income inequality has an effect on sexual dimorphism in height. Average height data come from the NCD-RisC health risk factor collaboration. Economic indicators are derived from the World Bank data archive and include gross domestic product (GDP), Gross National Income per capita adjusted for personal purchasing power (GNI_PPP), and income equality assessed by the Gini coefficient calculated by the Wagstaff method. Hypothesis 1 is supported. Greater income equality is most predictive of average height for both sexes. GNI_PPP explains a significant, but smaller, amount of the variation. National GDP has no association with height. Hypothesis 2 is rejected. With greater average adult height there is greater sexual dimorphism. Findings support a growing literature on the pernicious effects of inequality on growth in height and, by extension, on health. Gradients in height reflect gradients in social disadvantage. Inequality should be considered a pollutant that disempowers people from the resources needed for their own healthy growth and development and for the health and good growth of their children. © 2017 Wiley Periodicals, Inc.

Encounter Probability of Individual Wave Height

DEFF Research Database (Denmark)

Liu, Z.; Burcharth, H. F.

1998-01-01

wave height corresponding to a certain exceedence probability within a structure lifetime (encounter probability), based on the statistical analysis of long-term extreme significant wave height. Then the design individual wave height is calculated as the expected maximum individual wave height...... associated with the design significant wave height, with the assumption that the individual wave heights follow the Rayleigh distribution. However, the exceedence probability of such a design individual wave height within the structure lifetime is unknown. The paper presents a method for the determination...... of the design individual wave height corresponding to an exceedence probability within the structure lifetime, given the long-term extreme significant wave height. The method can also be applied for estimation of the number of relatively large waves for fatigue analysis of constructions....

Influence of the height of the vegetation cover in the variation of the kinetic energy of raindrops intercepted; Influencia de la altura de la cubierta vegetal en la variacion de la energia cinetica de las gotas de lluvia interceptadas

Energy Technology Data Exchange (ETDEWEB)

Roldan Soriano, M.

2009-07-01

The erosive capacity of raindrops is function of mass (size) and terminal velocity. Drop mass and velocity govern the inherent erosivity of rainfall through kinetic energy. Kinetic energy is a very important property of the rainfall because it is one of the sources of energy in the process of water erosion. Vegetative canopy intercepts the raindrops and causes a variation on this rainfall kinetic energy due to modification of diameters and velocities distributions. If the height of canopy is enough, the bigger intercepted drops could achieve high velocities and their kinetic energies can increases. In this paper a quantitative evaluation of the increase of kinetic energy of intercepted drops is obtained and it is showed that this kinetic energy increases exponentially with vegetation height. (Author) 9 refs.

Encounter Probability of Significant Wave Height

DEFF Research Database (Denmark)

Liu, Z.; Burcharth, H. F.

The determination of the design wave height (often given as the significant wave height) is usually based on statistical analysis of long-term extreme wave height measurement or hindcast. The result of such extreme wave height analysis is often given as the design wave height corresponding to a c...

Low-bias flat band-stop filter based on velocity modulated gaussian graphene superlattice

Science.gov (United States)

Sattari-Esfahlan, S. M.; Shojaei, S.

2018-05-01

Transport properties of biased planar Gaussian graphene superlattice (PGGSL) with Fermi velocity barrier is investigated by transfer matrix method (TMM). It is observed that enlargement of bias voltage over miniband width breaks the miniband to WSLs leads to suppressing resonant tunneling. Transmission spectrum shows flat wide stop-band property controllable by external bias voltage with stop-band width of near 200 meV. The simulations demonstrate that strong velocity barriers prevent tunneling of Dirac electrons leading to controllable enhancement of stop-band width. By increasing ratio of Fermi velocity in barriers to wells υc stop-band width increase. As wide transmission stop-band width (BWT) of filter is tunable from 40 meV to 340 meV is obtained by enhancing ratio of υc from 0.2 to 1.5, respectively. Proposed structure suggests easy tunable wide band-stop electronic filter with a modulated flat stop-band characteristic by height of electrostatic barrier and structural parameters. Robust sensitivity of band width to velocity barrier intensity in certain bias voltages and flat band feature of proposed filter may be opens novel venue in GSL based flat band low noise filters and velocity modulation devices.

Long-Term Athletic Development in Youth Alpine Ski Racing: The Effect of Physical Fitness, Ski Racing Technique, Anthropometrics and Biological Maturity Status on Injuries

Science.gov (United States)

Müller, Lisa; Hildebrandt, Carolin; Müller, Erich; Fink, Christian; Raschner, Christian

2017-01-01

Alpine ski racing is known to be a sport with a high risk of injuries. Because most studies have focused mainly on top-level athletes and on traumatic injuries, limited research exists about injury risk factors among youth ski racers. The aim of this study was to determine the intrinsic risk factors (anthropometrics, biological maturity, physical fitness, racing technique) for injury among youth alpine ski racers. Study participants were 81 youth ski racers attending a ski boarding school (50 males, 31 females; 9–14 years). A prospective longitudinal cohort design was used to monitor sports-related risk factors over two seasons and traumatic (TI) and overuse injuries (OI). At the beginning of the study, anthropometric characteristics (body height, body weight, sitting height, body mass index); biological maturity [status age at peak height velocity (APHV)]; physical performance parameters related to jump coordination, maximal leg and core strength, explosive and reactive strength, balance and endurance; and ski racing technique were assessed. Z score transformations normalized the age groups. Multivariate binary logistic regression (dependent variable: injury yes/no) and multivariate linear regression analyses (dependent variable: injury severity in total days of absence from training) were calculated. T-tests and multivariate analyses of variance were used to reveal differences between injured and non-injured athletes and between injury severity groups. The level of significance was set to p jump contact time; and higher drop jump reactive strength index were at a lower injury risk or more vulnerable for fewer days of absence from training. However, significant differences between injured and non-injured athletes were only observed with respect to the drop jump reactive strength index. Regular documentation of anthropometric characteristics, biological maturity and physical fitness parameters is crucial to help to prevent injury in youth ski racing. The present

Long-Term Athletic Development in Youth Alpine Ski Racing: The Effect of Physical Fitness, Ski Racing Technique, Anthropometrics and Biological Maturity Status on Injuries.

Science.gov (United States)

Müller, Lisa; Hildebrandt, Carolin; Müller, Erich; Fink, Christian; Raschner, Christian

2017-01-01

Alpine ski racing is known to be a sport with a high risk of injuries. Because most studies have focused mainly on top-level athletes and on traumatic injuries, limited research exists about injury risk factors among youth ski racers. The aim of this study was to determine the intrinsic risk factors (anthropometrics, biological maturity, physical fitness, racing technique) for injury among youth alpine ski racers. Study participants were 81 youth ski racers attending a ski boarding school (50 males, 31 females; 9-14 years). A prospective longitudinal cohort design was used to monitor sports-related risk factors over two seasons and traumatic (TI) and overuse injuries (OI). At the beginning of the study, anthropometric characteristics (body height, body weight, sitting height, body mass index); biological maturity [status age at peak height velocity (APHV)]; physical performance parameters related to jump coordination, maximal leg and core strength, explosive and reactive strength, balance and endurance; and ski racing technique were assessed. Z score transformations normalized the age groups. Multivariate binary logistic regression (dependent variable: injury yes/no) and multivariate linear regression analyses (dependent variable: injury severity in total days of absence from training) were calculated. T -tests and multivariate analyses of variance were used to reveal differences between injured and non-injured athletes and between injury severity groups. The level of significance was set to p core flexion strength; smaller core flexion:extension strength ratio; shorter drop jump contact time; and higher drop jump reactive strength index were at a lower injury risk or more vulnerable for fewer days of absence from training. However, significant differences between injured and non-injured athletes were only observed with respect to the drop jump reactive strength index. Regular documentation of anthropometric characteristics, biological maturity and physical fitness

The Relationship Between Maximum Isometric Strength and Ball Velocity in the Tennis Serve

Directory of Open Access Journals (Sweden)

Baiget Ernest

2016-12-01

Full Text Available The aims of this study were to analyze the relationship between maximum isometric strength levels in different upper and lower limb joints and serve velocity in competitive tennis players as well as to develop a prediction model based on this information. Twelve male competitive tennis players (mean ± SD; age: 17.2 ± 1.0 years; body height: 180.1 ± 6.2 cm; body mass: 71.9 ± 5.6 kg were tested using maximum isometric strength levels (i.e., wrist, elbow and shoulder flexion and extension; leg and back extension; shoulder external and internal rotation. Serve velocity was measured using a radar gun. Results showed a strong positive relationship between serve velocity and shoulder internal rotation (r = 0.67; p < 0.05. Low to moderate correlations were also found between serve velocity and wrist, elbow and shoulder flexion – extension, leg and back extension and shoulder external rotation (r = 0.36 – 0.53; p = 0.377 – 0.054. Bivariate and multivariate models for predicting serve velocity were developed, with shoulder flexion and internal rotation explaining 55% of the variance in serve velocity (r = 0.74; p < 0.001. The maximum isometric strength level in shoulder internal rotation was strongly related to serve velocity, and a large part of the variability in serve velocity was explained by the maximum isometric strength levels in shoulder internal rotation and shoulder flexion.

The Effect of Backward-Facing Step Height on Instability Growth and Breakdown in Swept Wing Boundary-Layer Transition

Science.gov (United States)

Eppink, Jenna L.; Wlezien, Richard W.; King, Rudolph A.; Choudhari, Meelan

2015-01-01

A low-speed experiment was performed on a swept at plate model with an imposed pressure gradient to determine the effect of a backward-facing step on transition in a stationary-cross flow dominated flow. Detailed hot-wire boundary-layer measurements were performed for three backward-facing step heights of approximately 36, 45, and 49% of the boundary-layer thickness at the step. These step heights correspond to a subcritical, nearly-critical, and critical case. Three leading-edge roughness configurations were tested to determine the effect of stationary-cross flow amplitude on transition. The step caused a local increase in amplitude of the stationary cross flow for the two larger step height cases, but farther downstream the amplitude decreased and remained below the baseline amplitude. The smallest step caused a slight local decrease in amplitude of the primary stationary cross flow mode, but the amplitude collapsed back to the baseline case far downstream of the step. The effect of the step on the amplitude of the primary cross flow mode increased with step height, however, the stationary cross flow amplitudes remained low and thus, stationary cross flow was not solely responsible for transition. Unsteady disturbances were present downstream of the step for all three step heights, and the amplitudes increased with increasing step height. The only exception is that the lower frequency (traveling crossflow-like) disturbance was not present in the lowest step height case. Positive and negative spikes in instantaneous velocity began to occur for the two larger step height cases and then grew in number and amplitude downstream of reattachment, eventually leading to transition. The number and amplitude of spikes varied depending on the step height and cross flow amplitude. Despite the low amplitude of the disturbances in the intermediate step height case, breakdown began to occur intermittently and the flow underwent a long transition region.

Analysis of non-thermal velocities in the solar corona

Directory of Open Access Journals (Sweden)

L. Contesse

2004-09-01

Full Text Available We describe new ground-based spectroscopic observations made using a 40-cm aperture coronagraph over a whole range of radial distances (up to heights of 12' above the limb and along four different heliocentric directions N, E, S and W. The analysis is limited to the study of the brightest forbidden emission line of Fe XIV at 530.3nm, in order to reach the best possible signal-to-noise ratio. To make the results statistically more significant, the extracted parameters are averaged over the whole length of the slit, and measurements are repeated fives times at each position; the corresponding dispersions in the results obtained along the slit are given. Central line profile intensities and full line widths (FWHM are plotted and compared to measurements published by other authors closer to the limb. We found widths and turbulent (non-thermal velocities of significantly higher values above the polar regions, especially when a coronal hole is present along the line of sight. We do not see a definitely decreasing behaviour of widths and turbulent velocities in equatorial directions for larger radial distances, as reported in the literature, although lower values are measured compared to the values in polar regions. The variation in the high corona is rather flat and a correlation diagram indicates that it is different for different regions and different radial distances. This seems to be the first analysis of the profiles of this coronal line, up to large heights above the limb for both equatorial and polar regions.

Physiological pattern of lumbar disc height

International Nuclear Information System (INIS)

Biggemann, M.; Frobin, W.; Brinckmann, P.

1997-01-01

Purpose of this study is to present a new method of quantifying objectively the height of all discs in lateral radiographs of the lumbar spine and of analysing the normal craniocaudal sequence pattern of lumbar disc heights. Methods: The new parameter is the ventrally measured disc height corrected for the dependence on the angle of lordosis by normalisation to mean angles observed in the erect posture of healthy persons. To eliminate radiographic magnification, the corrected ventral height is related to the mean depth of the cranially adjoining vertebra. In this manner lumbar disc heights were objectively measured in young, mature and healthy persons (146 males and 65 females). The craniocaudal sequence pattern was analysed by mean values from all persons and by height differences of adjoining discs in each individual lumbar spine. Results: Mean normative values demonstrated an increase in disc height between L1/L2 and L4/L5 and a constant or decreasing disc height between L4/L5 and L5/S1. However, this 'physiological sequence of disc height in the statistical mean' was observed in only 36% of normal males and 55% of normal females. Conclusion: The radiological pattern of the 'physiological sequence of lumbar disc height' leads to a relevant portion of false positive pathological results especially at L4/L5. An increase of disc height from L4/L5 to L5/S1 may be normal. The recognition of decreased disc height should be based on an abrupt change in the heights of adjoining discs and not on a deviation from a craniocaudal sequence pattern. (orig.) [de

Adult height, nutrition, and population health

Science.gov (United States)

Perkins, Jessica M.; Subramanian, S.V.; Davey Smith, George

2016-01-01

In this review, the potential causes and consequences of adult height, a measure of cumulative net nutrition, in modern populations are summarized. The mechanisms linking adult height and health are examined, with a focus on the role of potential confounders. Evidence across studies indicates that short adult height (reflecting growth retardation) in low- and middle-income countries is driven by environmental conditions, especially net nutrition during early years. Some of the associations of height with health and social outcomes potentially reflect the association between these environmental factors and such outcomes. These conditions are manifested in the substantial differences in adult height that exist between and within countries and over time. This review suggests that adult height is a useful marker of variation in cumulative net nutrition, biological deprivation, and standard of living between and within populations and should be routinely measured. Linkages between adult height and health, within and across generations, suggest that adult height may be a potential tool for monitoring health conditions and that programs focused on offspring outcomes may consider maternal height as a potentially important influence. PMID:26928678

Transport properties of Dirac electrons in graphene based double velocity-barrier structures in electric and magnetic fields

International Nuclear Information System (INIS)

Liu, Lei; Li, Yu-Xian; Liu, Jian-Jun

2012-01-01

Using transfer matrix method, transport properties in graphene based double velocity-barrier structures under magnetic and electric fields are numerically studied. It is found that velocity barriers for the velocity ratio (the Fermi velocity inside the barrier to that outside the barrier) less than one (or for the velocity ratio greater than one) have properties similar to electrostatic wells (or barriers). The velocity barriers for the velocity ratio greater than one significantly enlarge the resonant tunneling region of electrostatic barriers. In the presence of magnetic field, the plateau width of the Fano factor with a Poissonian value shortens (or broadens) for the case of the velocity ratio less than one (or greater than one). When the Fermi energy is equal to the electrostatic barrier height, for different values of the velocity ratio, both the conductivities and the Fano factors remain fixed. -- Highlights: ► We model graphene based velocity-barrier structures in electric and magnetic fields. ► Velocity barrier for ξ 1) have property similar to electrostatic well (barrier). ► Velocity barrier for ξ>1 enlarge the resonant tunneling region of electrostatic barrier. ► The plateau width of Fano factor shortens (or broadens) for the case of ξ 1). ► The conductivity remains fixed at the point of E F =U 0 for different values of ξ.

In defense of the classical height system

Science.gov (United States)

Foroughi, Ismael; Vaníček, Petr; Sheng, Michael; Kingdon, Robert William; Santos, Marcelo C.

2017-11-01

In many European countries, normal heights referred to the quasi-geoid as introduced by Molodenskij in the mid-20th century are preferred to the classical height system that consists of orthometric heights and the geoid as a reference surface for these heights. The rationale for this choice is supposed to be that in the classical height system, neither the geoid, nor the orthometric height can be ever known with centimetre level accuracy because one would need to know the topographical mass density to a level that can never be achieved. The aim of this paper is to question the validity of this rationale. The common way of assessing the congruency of a local geoid model and the orthometric heights is to compare the geoid heights with the difference between orthometric heights provided by leveling and geodetic heights provided by GNSS. On the other hand, testing the congruency of a quasi-geoidal model with normal height a similar procedure is used, except that instead of orthometric heights, normal heights are employed. For the area of Auvergne, France, which is now a more or less standard choice for precise geoid or quasi-geoid testing, only the normal heights are supplied by the Institute Geographic National, the provider of the data. This is clearly the consequence of the European preference for the Molodenskij system. The quality of the height system is to be judged by the congruency of the difference of the geoid/quasi-geoid heights subtracted from the geodetic heights and orthometric/normal heights. To assess the congruency of the classical height system, the Helmert approximation of orthometric heights is typically used as the transformation between normal and Helmert's heights is easily done. However, the evaluation of the differences between Helmert's and the rigorous orthometric heights is somewhat more involved as will be seen from the review in this paper. For the area of interest, the differences between normal and Helmert's heights at the control

On the Extreme Wave Height Analysis

DEFF Research Database (Denmark)

Burcharth, H. F.; Liu, Zhou

1994-01-01

The determination of the design wave height is usually based on the statistical analysis of long-term extreme wave height measurements. After an introduction to the procedure of the extreme wave height analysis, the paper presents new development concerning various aspects of the extreme wave...... height analysis. Finally, the paper gives a practical example based on a data set of the hindcasted wave heights for a deep water location in the Mediterranean Sea....

Anticipatory Postural Control of Stability during Gait Initiation Over Obstacles of Different Height and Distance Made Under Reaction-Time and Self-Initiated Instructions.

Science.gov (United States)

Yiou, Eric; Artico, Romain; Teyssedre, Claudine A; Labaune, Ombeline; Fourcade, Paul

2016-01-01

Despite the abundant literature on obstacle crossing in humans, the question of how the central nervous system (CNS) controls postural stability during gait initiation with the goal to clear an obstacle remains unclear. Stabilizing features of gait initiation include anticipatory postural adjustments (APAs) and lateral swing foot placement. To answer the above question, 14 participants initiated gait as fast as possible in three conditions of obstacle height, three conditions of obstacle distance and one obstacle-free (control) condition. Each of these conditions was performed with two levels of temporal pressure: reaction-time (high-pressure) and self-initiated (low-pressure) movements. A mechanical model of the body falling laterally under the influence of gravity and submitted to an elastic restoring force is proposed to assess the effect of initial (foot-off) center-of-mass position and velocity (or "initial center-of-mass set") on the stability at foot-contact. Results showed that the anticipatory peak of mediolateral (ML) center-of-pressure shift, the initial ML center-of-mass velocity and the duration of the swing phase, of gait initiation increased with obstacle height, but not with obstacle distance. These results suggest that ML APAs are scaled with swing duration in order to maintain an equivalent stability across experimental conditions. This statement is strengthened by the results obtained with the mechanical model, which showed how stability would be degraded if there was no adaptation of the initial center-of-mass set to swing duration. The anteroposterior (AP) component of APAs varied also according to obstacle height and distance, but in an opposite way to the ML component. Indeed, results showed that the anticipatory peak of backward center-of-pressure shift and the initial forward center-of-mass set decreased with obstacle height, probably in order to limit the risk to trip over the obstacle, while the forward center-of-mass velocity at foot

ANTICIPATORY POSTURAL CONTROL OF STABILITY DURING GAIT INITIATION OVER OBSTACLES OF DIFFERENT HEIGHT AND DISTANCE MADE UNDER REACTION-TIME AND SELF-INITIATED INSTRUCTIONS

Directory of Open Access Journals (Sweden)

Eric Yiou

2016-09-01

Full Text Available Despite the abundant literature on obstacle crossing in humans, the question of how the central nervous system (CNS controls postural stability during gait initiation with the goal to clear an obstacle remains unclear. Stabilizing features of gait initiation include anticipatory postural adjustments (APAs and lateral swing foot placement. To answer the above question, fourteen participants initiated gait as fast as possible in three conditions of obstacle height, three conditions of obstacle distance, and one obstacle-free (control condition. Each of these conditions was performed with two levels of temporal pressure: reaction-time (high-pressure and self-initiated (low-pressure movements. A mechanical model of the body falling laterally under the influence of gravity and submitted to an elastic restoring force is proposed to assess the effect of initial (foot-off center-of-mass position and velocity (or initial center-of-mass set on stability at foot-contact. Results showed that the anticipatory peak of mediolateral center-of-pressure shif, the initial mediolateral center-of-mass velocity and the duration of the swing phase of gait initiation increased with obstacle height, but not with obstacle distance. These results suggest that mediolateral APAs are scaled with swing duration in order to maintain an equivalent stability across experimental conditions. This statement is strengthened by the results obtained with the mechanical model, which showed how stability would be degraded if there was no adaptation of the initial center-of-mass set to swing duration. The anteroposterior component of APAs varied also according to obstacle height and distance, but in an opposite way to the mediolateral component. Indeed, results showed that the anticipatory peak of backward center-of-pressure shift and the initial forward center-of-mass set decreased with obstacle height, probably in order to limit the risk to trip over the obstacle, while the forward

Real group velocity in a medium with dissipation

International Nuclear Information System (INIS)

Muschietti, L.; Dum, C.T.

1993-01-01

When a medium is dissipative, the classic expression for the group velocity, dω/dk, is complex with an imaginary part often being far from negligible. To clarify the role of this imaginary term, the motion of a wave packet in a dissipative, homogeneous medium is examined. The integral representation of the packet is analyzed by means of a saddle-point method. It is shown that in a moving frame attached to its maximum the packet looks self-similar. A Gaussian packet keeps its Gaussian identity, as is familiar for the case of a nondissipative medium. However, the central wave number of the packet slowly changes because of a differential damping among the Fourier components: Im(dω/dk)=dγ/dk≠0, where ω≡ω r +iγ. The packet height can be computed self-consistently as integrated damping (or growth). The real group velocity becomes a time-dependent combination of Re(dω/dk) and Im(dω/dk). Only where the medium is both homogeneous and loss free, does the group velocity remain constant. Simple ''ray-tracing equations'' are derived to follow the packet centers in coordinate and Fourier spaces. The analysis is illustrated with a comparison to geometric optics, and by two applications: the case of a medium with some resonant damping (or growth) and the propagation of whistler waves in a collisional plasma

Measurement of Aortic Pulse Wave Velocity With a Connected Bathroom Scale.

Science.gov (United States)

Campo, David; Khettab, Hakim; Yu, Roger; Genain, Nicolas; Edouard, Paul; Buard, Nadine; Boutouyrie, Pierre

2017-09-01

Measurement of arterial stiffness should be more available. Our aim was to show that aortic pulse wave velocity can be reliably measured with a bathroom scale combining the principles of ballistocardiography (BCG) and impedance plethysmography on a single foot. The calibration of the bathroom scale was conducted on a group of 106 individuals. The aortic pulse wave velocity was measured with the SphygmoCor in the supine position. Three consecutive measurements were then performed on the Withings scale in the standing position. This aorta-leg pulse transit time (alPTT) was then converted into a velocity with the additional input of the height of the person. Agreement between the SphygmoCor and the bathroom scale so calibrated is assessed on a separate group of 86 individuals, following the same protocol. The bias is 0.25 m·s-1 and the SE 1.39 m·s-1. This agreement with Sphygmocor is "acceptable" according to the ARTERY classification. The alPTT correlated well with cfPTT with (Spearman) R = 0.73 in pooled population (cal 0.79, val 0.66). The aorta-leg pulse wave velocity correlated with carotid-femoral pulse wave velocity with R = 0.76 (cal 0.80, val 0.70). Estimation of the aortic pulse wave velocity is feasible with a bathroom scale. Further investigations are needed to improve the repeatability of measurements and to test their accuracy in different populations and conditions. © The Author 2017. Published by Oxford University Press on behalf of American Journal of Hypertension.

The influence of heel height on utilized coefficient of friction during walking.

Science.gov (United States)

Blanchette, Mark G; Brault, John R; Powers, Christopher M

2011-05-01

Wearing high heel shoes has been associated with an increased potential for slips and falls. The association between wearing high heels and the increased potential for slipping suggests that the friction demand while wearing high heels may be greater when compared to wearing low heel shoes. The purpose of this study was to determine if heel height affects utilized friction (uCOF) during walking. A secondary purpose of this study was to compare kinematics at the ankle, knee, and hip that may explain uCOF differences among shoes with varied heel heights. Fifteen healthy women (mean age 24.5±2.5yrs) participated. Subjects walked at self-selected velocity under 3 different shoe conditions that varied in heel height (low: 1.27cm, medium: 6.35cm, and high: 9.53cm). Ground reaction forces (GRFs) were recorded using a force platform (1560Hz). Kinematic data were obtained using an 8 camera motion analysis system (120Hz). Utilized friction was calculated as the ratio of resultant shear force to vertical force. One-way repeated measures ANOVAs were performed to test for differences in peak uCOF, GRFs at peak uCOF and lower extremity joint angles at peak uCOF. On average, peak uCOF was found to increase with heel height. The increased uCOF observed in high heel shoes was related to an increase in the resultant shear force and decrease in the vertical force. Our results signify the need for proper public education and increased footwear industry awareness of how high heel shoes affect slip risk. Copyright © 2011 Elsevier B.V. All rights reserved.

On The Ion Drift Contribution To The Phase Velocity of Electrojet Irregularities

Science.gov (United States)

Uspensky, M.; Koustov, A.; Janhunen, P.; Pellinen, R.; Danskin, D.; Nozawa, S.

The ion drift effect is often ignored in the interpretation of VHF Doppler measure- ments. For example, in the STARE experiment it is assumed that the line-of-sight velocity measured at large flow angles is simply a cosine component of the true elec- tron drift. Previous studies seem to support this assumption, though only to a certain degree. In this study we consider a 3.5-hour morning event of joint STARE-EISCAT observa- tions for which the STARE-Finland radar velocity was mainly larger than the EISCAT convection component. A moderate 5-20 deg offset between the EISCAT convection azimuth and its STARE estimate was also observed. We show that both the STARE- Finland radar velocity "over-speed" and the azimuthal offset between the EISCAT and STARE convection vectors can be explained by fluid plasma theory arguments if the ion drift contribution to the irregularity phase velocity under the condition of moder- ate backscatter off-orthogonality is taken into account. The ion effects were enhanced because of a lifting up of the entire E-region seen by the EISCAT. It perhaps resulted in an increase of the STARE echo heights and aspect angles. The latter are of the order of 1 deg at the top of the electrojet layer. We also compare STARE convection magni- tudes and true velocities measured by the EISCAT to study the potential impact of the ion motions on the STARE velocity estimates.

Maximum range of a projectile launched from a height h: a non-calculus treatment

International Nuclear Information System (INIS)

Ganci, S; Lagomarsino, D

2014-01-01

The classical example of problem solving, maximizing the range of a projectile launched from height h with velocity v over the ground level, has received various solutions. In some of these, one can find the maximization of the range R by differentiating R as a function of an independent variable or through the implicit differentiation in Cartesian or polar coordinates. In other papers, various elegant non-calculus solutions can be found. In this paper, this problem is revisited on the basis of the elementary analytical geometry and the trigonometry only. (papers)

Maximum range of a projectile launched from a height h: a non-calculus treatment

Science.gov (United States)

Ganci, S.; Lagomarsino, D.

2014-07-01

The classical example of problem solving, maximizing the range of a projectile launched from height h with velocity v over the ground level, has received various solutions. In some of these, one can find the maximization of the range R by differentiating R as a function of an independent variable or through the implicit differentiation in Cartesian or polar coordinates. In other papers, various elegant non-calculus solutions can be found. In this paper, this problem is revisited on the basis of the elementary analytical geometry and the trigonometry only.

Effect of Core Training on Male Handball Players' Throwing Velocity.

Science.gov (United States)

Manchado, Carmen; García-Ruiz, José; Cortell-Tormo, Juan Manuel; Tortosa-Martínez, Juan

2017-02-01

In handball, throwing velocity is considered to be one of the essential factors in achieving the ultimate aim of scoring a goal. The objective of the present study was to analyze the effect of a core training program on throwing velocity in 30 handball players (age 18.7 ± 3.4 years, body height 179.3 ± 7.0 cm, body mass 78.9 ± 7.7 kg), 16 of whom were in the junior category and 14 of whom were in the senior category. The 30 players were randomly divided into two groups, the control group (n = 15) and the experimental group (n = 15). For a period of ten weeks, both groups attended their regular handball training sessions (four per week), but in addition, the experimental group participated in a program specifically aimed at progressively strengthening the lumbo-pelvic region and consisting of seven exercises performed after the general warm-up in each regular session. Pre- and post-tests were carried out to analyze each player's throwing velocity from different throwing positions and thus assess the effects of this specific training program. Statistically significant differences (p ≤ 0.05) in throwing velocity were observed between the experimental group, which presented a percentage improvement of 4.5%, and the control group, which did not show any improvement. The results seem to indicate that an increase in the strength and stability of the lumbo-pelvic region can contribute to an improvement in the kinetic chain of the specific movement of throwing in handball, thus, increasing throwing velocity.

Effect of Core Training on Male Handball Players’ Throwing Velocity

Science.gov (United States)

García-Ruiz, José; Cortell-Tormo, Juan Manuel; Tortosa-Martínez, Juan

2017-01-01

Abstract In handball, throwing velocity is considered to be one of the essential factors in achieving the ultimate aim of scoring a goal. The objective of the present study was to analyze the effect of a core training program on throwing velocity in 30 handball players (age 18.7 ± 3.4 years, body height 179.3 ± 7.0 cm, body mass 78.9 ± 7.7 kg), 16 of whom were in the junior category and 14 of whom were in the senior category. The 30 players were randomly divided into two groups, the control group (n = 15) and the experimental group (n = 15). For a period of ten weeks, both groups attended their regular handball training sessions (four per week), but in addition, the experimental group participated in a program specifically aimed at progressively strengthening the lumbo-pelvic region and consisting of seven exercises performed after the general warm-up in each regular session. Pre- and post-tests were carried out to analyze each player’s throwing velocity from different throwing positions and thus assess the effects of this specific training program. Statistically significant differences (p ≤ 0.05) in throwing velocity were observed between the experimental group, which presented a percentage improvement of 4.5%, and the control group, which did not show any improvement. The results seem to indicate that an increase in the strength and stability of the lumbo-pelvic region can contribute to an improvement in the kinetic chain of the specific movement of throwing in handball, thus, increasing throwing velocity. PMID:28469756

Scaling properties of velocity and temperature spectra above the surface friction layer in a convective atmospheric boundary layer

Directory of Open Access Journals (Sweden)

K. G. McNaughton

2007-06-01

Full Text Available We report velocity and temperature spectra measured at nine levels from 1.42 meters up to 25.7 m over a smooth playa in Western Utah. Data are from highly convective conditions when the magnitude of the Obukhov length (our proxy for the depth of the surface friction layer was less than 2 m. Our results are somewhat similar to the results reported from the Minnesota experiment of Kaimal et al. (1976, but show significant differences in detail. Our velocity spectra show no evidence of buoyant production of kinetic energy at at the scale of the thermal structures. We interpret our velocity spectra to be the result of outer eddies interacting with the ground, not "local free convection".

We observe that velocity spectra represent the spectral distribution of the kinetic energy of the turbulence, so we use energy scales based on total turbulence energy in the convective boundary layer (CBL to collapse our spectra. For the horizontal velocity spectra this scale is (z_i ε_o^2/3, where z_i is inversion height and ε_o is the dissipation rate in the bulk CBL. This scale functionally replaces the Deardorff convective velocity scale. Vertical motions are blocked by the ground, so the outer eddies most effective in creating vertical motions come from the inertial subrange of the outer turbulence. We deduce that the appropriate scale for the peak region of the vertical velocity spectra is (z ε_o^2/3 where z is height above ground. Deviations from perfect spectral collapse under these scalings at large and small wavenumbers are explained in terms of the energy transport and the eddy structures of the flow.

We find that the peaks of the temperature spectra collapse when wavenumbers are scaled using (z^1/2 z_i^1/2. That is, the lengths of the thermal structures depend on both the lengths of the

Estimation of blood velocity vectors using transverse ultrasound beam focusing and cross-correlation

DEFF Research Database (Denmark)

Jensen, Jørgen Arendt; Lacasa, Isabel Rodriguez

1999-01-01

program. Simulations are shown for a parabolic velocity profile for flow-to-beam angles of 30, 45, 60, and 90 degrees using a 64 elements linear array with a center frequency of 3 MHz, a pitch of 0.3 mm, and an element height of 5 mm. The peak velocity in the parabolic flow was 0.5 m/s, and the pulse...... repetition frequency was 3.5 kHz. Using four pulse-echo lines, the parabolic flow profile was found with a standard deviation of 0.028 m/s at 60 degrees and 0.092 m/s at 90 degrees (transverse to the ultrasound beam), corresponding to accuracies of 5.6% and 18.4%. Using ten lines gave standard deviations...

Impact of Assimilating Surface Velocity Observations on the Model Sea Surface Height Using the NCOM-4DVAR

Science.gov (United States)

2016-09-26

the ensemble Kalman filter and the ensemble Kalman smoother: A comparison study using a nonlinear reduced gravity ocean model.OceanModell., 12, 378...using local ensemble transform Kalman filter and optimum-interpolation assimilation schemes. Ocean Modell., 69, 22–38, doi:10.1016/j.ocemod.2013.05.002...observations are assimi- lated. This gives a sense of the added value from the inclusion of velocity observations with the standard set of temperature

Height outcome of the recombinant human growth hormone treatment in Turner syndrome: a meta-analysis

Directory of Open Access Journals (Sweden)

Ping Li

2018-04-01

Full Text Available Objective: This study sought to determine the effect of the recombinant human growth hormone (rhGH treatment of Turner syndrome (TS on height outcome. Methods: We searched in MEDLINE, EMBASE and Cochrane Central Register of Controlled Trials and Cochrane Database of Systematic Reviews. A literature search identified 640 records. After screening and full-text assessment, 11 records were included in the systematic review. Methodological quality was assessed using the Cochrane Risk of Bias tool. RevMan 5.3 software was used for meta-analysis. We also assessed the quality of evidence with the GRADE system. Results: Compared with controls, rhGH therapy led to increased final height (MD = 7.22 cm, 95% CI 5.27–9.18, P < 0.001, I2 = 4%; P = 0.18, height standard deviation (HtSDS (SMD = 1.22, 95% CI 0.88–1.56, P < 0.001, I2 = 49%; P = 0.14 and height velocity (HV (MD 2.68 cm/year; 95% CI 2.34, 3.02; P < 0.001, I2 = 0%; P = 0.72. There was a small increase in bone age (SMD 0.32 years; 95% CI 0.1, 0.54; P = 0.004, I2 = 73%; P = 0.02 after rhGH therapy for 12 months. What is more, the rhGH/oxandrolone combination therapy suggested greater final height (MD 2.46 cm; 95% CI 0.73, 4.18; P = 0.005, I2 = 32%; P = 0.22, increase and faster HV (SMD 1.67 cm/year; 95% CI 1.03, 2.31; P < 0.03, I2 = 80%; P < 0.001, with no significant increase in HtSDS and bone maturation compared with rhGH therapy alone. Conclusions: For TS patients, rhGH alone or with concomitant use of oxandrolone treatment had advantages on final height.

Investigations into the influence of the tup velocity and the heat treatment on the dynamic fracture toughness of Inconel 625

International Nuclear Information System (INIS)

Krompholz, K.; Tipping, P.; Ullrich, G.

1983-09-01

Experiments were performed with an instrumented impact machine using different drop heights, on the nickel base alloy Inconel 625 in the as received state and after heat treatment for about 1000 h at 923 K. The absorbed impact energy can be obtained either by the direct dial reading, by the integration of the load versus load point displacement diagram or by the integration of the load versus time diagram, knowing the initial impact velocity of the tup. In all cases the agreement was excellent. It is shown that, (i) the dynamic fracture toughness is dependent on the tup velocity and as a consequence on the total energy of the hammer at the different drop heights; (ii) the embrittlement during heat treatment is not combined with a decrease in the fracture toughness although a strong decrease in the absorbed impact energy is observed; (iii) defining a dynamic stress from the velocity dependence of the fracture toughness, the stress is higher for the embrittled material - a tendency verified by tensile tests; (iv) the dynamic fracture toughness can be correlated with the absorbed impact energy up to the load maximum for the heat treated material while the as received material exhibits no such dependency. The change in the tup velocity during the impact process is only small for this type of material. (Auth.)

More practical critical height sampling.

Science.gov (United States)

Thomas B. Lynch; Jeffrey H. Gove

2015-01-01

Critical Height Sampling (CHS) (Kitamura 1964) can be used to predict cubic volumes per acre without using volume tables or equations. The critical height is defined as the height at which the tree stem appears to be in borderline condition using the point-sampling angle gauge (e.g. prism). An estimate of cubic volume per acre can be obtained from multiplication of the...

Blanking Clearance and Punch Velocity Effects on The Sheared Edge Characteristic in Micro-Blanking of Commercially Pure Copper Sheet

Directory of Open Access Journals (Sweden)

Didin Zakaria Lubis

2017-11-01

Full Text Available This study aims to identify the influences between clearance and punch velocity on the part edge quality of blanked parts. Experiments have been conducted using material copper, punch-die clearance and punch velocity variations. In order to determine the reachable punch-die clearance and punch velocity required for blanking. The quality of the part-edge characteristics shows that higher punch velocity and decreases clearance value can improve the part-edge quality, resulting in smaller burr height and rollover, and a larger shear zone. Furthermore, it could be observed that the part-edge quality improvement when blanking with high punch velocity is much more distinct for stele than for copper. According to blanking theory, this improvement was expected because copper have much higher heat conduction coefficients. Therefore, the heat dissipates faster and the desired stress relief effect does not take place to the same degree as for stele.

Imagery and fear influence height perception.

Science.gov (United States)

Clerkin, Elise M; Cody, Meghan W; Stefanucci, Jeanine K; Proffitt, Dennis R; Teachman, Bethany A

2009-04-01

The current study tested whether height overestimation is related to height fear and influenced by images of falling. To assess perceptual biases, participants high (n=65) versus low (n=64) in height fear estimated the vertical extents of two balconies using a visual matching task. On one of the balconies, participants engaged in an imagery exercise designed to enhance the subjective sense that they were acting in a dangerous environment by picturing themselves falling. As expected, we found that individuals overestimated the balcony's height more after they imagined themselves falling, particularly if they were already afraid of heights. These findings suggest that height fear may serve as a vulnerability factor that leads to perceptual biases when triggered by a stressor (in this case, images of falling).

Development and validity of a scale of perception of velocity in resistance exercise.

Science.gov (United States)

Bautista, Iker J; Chirosa, Ignacio J; Chirosa, Luis J; Martín, Ignacio; González, Andrés; Robertson, Robert J

2014-09-01

This aims of this study were twofold; 1) to development a new scale of perceived velocity in the bench press exercise and 2) to examine the scales concurrent validity. Twenty one physically active males with mean ±SD age, height and weights of: 27.5 ± 4.7 years, 1.77 ± 0.07 m, and 79.8 ± 10.3 kg respectively, took part in the study. The criterion variable used to test the validity of the new scale was the mean execution velocity (Velreal) of the bench press exercise. Three intensities (light loads [ 70% 1RM]) were measured randomly during 5 days of testing. Perceived velocity (Velscale) was measured immediately after each exercise set using the new scale. A positive linear correlation (r range = 0.69 to 0.81) was found in all three intensities, analyzed individually, between the Velreal and Velscale. Pearson correlations showed a greater frequency of scale use resulted higher correlation values (range r = 0.88 to 0.96). This study provides evidence of the concurrent validity of a new scale of perceived velocity in the bench press exercise in trained adult males. These results suggest the exercise intensity of the bench press can be quantified quickly and effective using this new scale of perceived velocity, particularly when training for maximum power. Key PointsMeasurement of perception of velocity can complement other scales of perception such as the 15 category Borg scale or the OMNI-RES.The results obtained in this study show that there was a positive correlation between the perceived velocity measured by the scale and actual velocityRegular use of the new scale of perceived velocity in external resistance training provides athletes with continuous feedback of execution velocity in each repetition and set, especially with high power loads.

Genetic determinants of height growth assessed longitudinally from infancy to adulthood in the northern Finland birth cohort 1966.

Directory of Open Access Journals (Sweden)

Ulla Sovio

2009-03-01

Full Text Available Recent genome-wide association (GWA studies have identified dozens of common variants associated with adult height. However, it is unknown how these variants influence height growth during childhood. We derived peak height velocity in infancy (PHV1 and puberty (PHV2 and timing of pubertal height growth spurt from parametric growth curves fitted to longitudinal height growth data to test their association with known height variants. The study consisted of N = 3,538 singletons from the prospective Northern Finland Birth Cohort 1966 with genotype data and frequent height measurements (on average 20 measurements per person from 0-20 years. Twenty-six of the 48 variants tested associated with adult height (p<0.05, adjusted for sex and principal components in this sample, all in the same direction as in previous GWA scans. Seven SNPs in or near the genes HHIP, DLEU7, UQCC, SF3B4/SV2A, LCORL, and HIST1H1D associated with PHV1 and five SNPs in or near SOCS2, SF3B4/SV2A, C17orf67, CABLES1, and DOT1L with PHV2 (p<0.05. We formally tested variants for interaction with age (infancy versus puberty and found biologically meaningful evidence for an age-dependent effect for the SNP in SOCS2 (p = 0.0030 and for the SNP in HHIP (p = 0.045. We did not have similar prior evidence for the association between height variants and timing of pubertal height growth spurt as we had for PHVs, and none of the associations were statistically significant after correction for multiple testing. The fact that in this sample, less than half of the variants associated with adult height had a measurable effect on PHV1 or PHV2 is likely to reflect limited power to detect these associations in this dataset. Our study is the first genetic association analysis on longitudinal height growth in a prospective cohort from birth to adulthood and gives grounding for future research on the genetic regulation of human height during different periods of growth.

Genetic Determinants of Height Growth Assessed Longitudinally from Infancy to Adulthood in the Northern Finland Birth Cohort 1966

Science.gov (United States)

Sovio, Ulla; Bennett, Amanda J.; Millwood, Iona Y.; Molitor, John; O'Reilly, Paul F.; Timpson, Nicholas J.; Kaakinen, Marika; Laitinen, Jaana; Haukka, Jari; Pillas, Demetris; Tzoulaki, Ioanna; Molitor, Jassy; Hoggart, Clive; Coin, Lachlan J. M.; Whittaker, John; Pouta, Anneli; Hartikainen, Anna-Liisa; Freimer, Nelson B.; Widen, Elisabeth; Peltonen, Leena; Elliott, Paul; McCarthy, Mark I.; Jarvelin, Marjo-Riitta

2009-01-01

Recent genome-wide association (GWA) studies have identified dozens of common variants associated with adult height. However, it is unknown how these variants influence height growth during childhood. We derived peak height velocity in infancy (PHV1) and puberty (PHV2) and timing of pubertal height growth spurt from parametric growth curves fitted to longitudinal height growth data to test their association with known height variants. The study consisted of N = 3,538 singletons from the prospective Northern Finland Birth Cohort 1966 with genotype data and frequent height measurements (on average 20 measurements per person) from 0–20 years. Twenty-six of the 48 variants tested associated with adult height (p<0.05, adjusted for sex and principal components) in this sample, all in the same direction as in previous GWA scans. Seven SNPs in or near the genes HHIP, DLEU7, UQCC, SF3B4/SV2A, LCORL, and HIST1H1D associated with PHV1 and five SNPs in or near SOCS2, SF3B4/SV2A, C17orf67, CABLES1, and DOT1L with PHV2 (p<0.05). We formally tested variants for interaction with age (infancy versus puberty) and found biologically meaningful evidence for an age-dependent effect for the SNP in SOCS2 (p = 0.0030) and for the SNP in HHIP (p = 0.045). We did not have similar prior evidence for the association between height variants and timing of pubertal height growth spurt as we had for PHVs, and none of the associations were statistically significant after correction for multiple testing. The fact that in this sample, less than half of the variants associated with adult height had a measurable effect on PHV1 or PHV2 is likely to reflect limited power to detect these associations in this dataset. Our study is the first genetic association analysis on longitudinal height growth in a prospective cohort from birth to adulthood and gives grounding for future research on the genetic regulation of human height during different periods of growth. PMID:19266077

Low-velocity Impact Response of a Nanocomposite Beam Using an Analytical Model

Directory of Open Access Journals (Sweden)

Mahdi Heydari Meybodi

Full Text Available AbstractLow-velocity impact of a nanocomposite beam made of glass/epoxy reinforced with multi-wall carbon nanotubes and clay nanoparticles is investigated in this study. Exerting modified rule of mixture (MROM, the mechanical properties of nanocomposite including matrix, nanoparticles or multi-wall carbon nanotubes (MWCNT, and fiber are attained. In order to analyze the low-velocity impact, Euler-Bernoulli beam theory and Hertz's contact law are simultaneously employed to govern the equations of motion. Using Ritz's variational approximation method, a set of nonlinear equations in time domain are obtained, which are solved using a fourth order Runge-Kutta method. The effect of different parameters such as adding nanoparticles or MWCNT's on maximum contact force and energy absorption, stacking sequence, geometrical dimensions (i.e., length, width and height, and initial velocity of the impactor have been studied comprehensively on dynamic behavior of the nanocomposite beam. In addition, the result of analytical model is compared with Finite Element Modeling (FEM.The results reveal that the effect of nanoparticles on energy absorption is more considerable at higher impact energies.

Combined Treatment with Gonadotropin-releasing Hormone Analog and Anabolic Steroid Hormone Increased Pubertal Height Gain and Adult Height in Boys with Early Puberty for Height.

Science.gov (United States)

Tanaka, Toshiaki; Naiki, Yasuhiro; Horikawa, Reiko

2012-04-01

Twenty-one boys with a height of 135 cm or less at onset of puberty were treated with a combination of GnRH analog and anabolic steroid hormone, and their pubertal height gain and adult height were compared with those of untreated 29 boys who enter puberty below 135 cm. The mean age at the start of treatment with a GnRH analog, leuprorelin acetate depot (Leuplin(®)) was 12.3 yr, a mean of 1.3 yr after the onset of puberty, and GnRH analog was administered every 3 to 5 wk thereafter for a mean duration of 4.1 yr. The anabolic steroid hormone was started approximately 1 yr after initiation of treatment with the GnRH analog. The mean pubertal height gain from onset of puberty till adult height was significantly greater in the combination treatment group (33.9 cm) than in the untreated group (26.4 cm) (ppenis and pubic hair is promoted by the anabolic steroid hormone, no psychosocial problems arose because of delayed puberty. No clinically significant adverse events appeared. Combined treatment with GnRH analog and anabolic steroid hormone significantly increased height gain during puberty and adult height in boys who entered puberty with a short stature, since the period until epiphyseal closure was extended due to deceleration of the bone age maturation by administration of the GnRH analog and the growth rate at this time was maintained by the anabolic steroid hormone.

Maternal Height and Child Growth Patterns

OpenAIRE

Addo, O. Yaw; Stein, Aryeh D.; Fall, Caroline H.; Gigante, Denise P.; Guntupalli, Aravinda M.; Horta, Bernardo L.; Kuzawa, Christopher W.; Lee, Nanette; Norris, Shane A.; Prabhakaran, Poornima; Richter, Linda M.; Sachdev, Harshpal S.; Martorell, Reynaldo

2013-01-01

OBJECTIVE:\\ud To examine associations between maternal height and child growth during 4 developmental periods: intrauterine, birth to age 2 years, age 2 years to mid-childhood (MC), and MC to adulthood.\\ud \\ud STUDY DESIGN:\\ud Pooled analysis of maternal height and offspring growth using 7630 mother-child pairs from 5 birth cohorts (Brazil, Guatemala, India, the Philippines, and South Africa). We used conditional height measures that control for collinearity in height across periods. We estim...

Development and Validity of a Scale of Perception of Velocity in Resistance Exercise

Directory of Open Access Journals (Sweden)

Iker J. Bautista

2014-09-01

Full Text Available This aims of this study were twofold; 1 to development a new scale of perceived velocity in the bench press exercise and 2 to examine the scales concurrent validity. Twenty one physically active males with mean ±SD age, height and weights of: 27.5 ± 4.7 years, 1.77 ± 0.07 m, and 79.8 ± 10.3 kg respectively, took part in the study. The criterion variable used to test the validity of the new scale was the mean execution velocity (Velreal of the bench press exercise. Three intensities (light loads [ 70% 1RM] were measured randomly during 5 days of testing. Perceived velocity (Velscale was measured immediately after each exercise set using the new scale. A positive linear correlation (r range = 0.69 to 0.81 was found in all three intensities, analyzed individually, between the Velreal and Velscale. Pearson correlations showed a greater frequency of scale use resulted higher correlation values (range r = 0.88 to 0.96. This study provides evidence of the concurrent validity of a new scale of perceived velocity in the bench press exercise in trained adult males. These results suggest the exercise intensity of the bench press can be quantified quickly and effective using this new scale of perceived velocity, particularly when training for maximum power.

Standardizing Scale Height Computation of Maven Ngims Neutral Data and Variations Between Exobase and Homeopause Scale Heights

Science.gov (United States)

Elrod, M. K.; Slipski, M.; Curry, S.; Williamson, H. N.; Benna, M.; Mahaffy, P. R.

2017-12-01

The MAVEN NGIMS team produces a level 3 product which includes the computation of Ar scale height an atmospheric temperatures at 200 km. In the latest version (v05_r01) this has been revised to include scale height fits for CO2, N2 O and CO. Members of the MAVEN team have used various methods to compute scale heights leading to significant variations in scale height values depending on fits and techniques within a few orbits even, occasionally, the same pass. Additionally fitting scale heights in a very stable atmosphere like the day side vs night side can have different results based on boundary conditions. Currently, most methods only compute Ar scale heights as it is most stable and reacts least with the instrument. The NGIMS team has chosen to expand these fitting techniques to include fitted scale heights for CO2, N2, CO, and O. Having compared multiple techniques, the method found to be most reliable for most conditions was determined to be a simple fit method. We have focused this to a fitting method that determines the exobase altidude of the CO2 atmosphere as a maximum altitude for the highest point for fitting, and uses the periapsis as the lowest point and then fits the altitude versus log(density). The slope of altitude vs log(density) is -1/H where H is the scale height of the atmosphere for each species. Since this is between the homeopause and the exobase, each species will have a different scale height by this point. This is being released as a new standardization for the level 3 product, with the understanding that scientists and team members will continue to compute more precise scale heights and temperatures as needed based on science and model demands. This is being released in the PDS NGIMS level 3 v05 files for August 2017. Additionally, we are examining these scale heights for variations seasonally, diurnally, and above and below the exobase. The atmosphere is significantly more stable on the dayside than on the nightside. We have also found

Degeneration and height of cervical discs classified from MRI compared with precise height measurements from radiographs

International Nuclear Information System (INIS)

Kolstad, Frode; Myhr, Gunnar; Kvistad, Kjell Arne; Nygaard, Oystein P.; Leivseth, Gunnar

2005-01-01

Study design: Descriptive study comparing MRI classifications with measurements from radiographs. Objectives: 1.Define the relationship between MRI classified cervical disc degeneration and objectively measured disc height. 2.Assess the level of inter- and intra-observer errors using MRI in defining cervical disc degeneration. Summary of background data: Cervical spine degeneration has been defined radiologically by loss of disc height, decreased disc and bone marrow signal intensity and disc protrusion/herniation on MRI. The intra- and inter-observer error using MRI in defining cervical degeneration influences data interpretation. Few previous studies have addressed this source of error. The relation and time sequence between cervical disc degeneration classified by MRI and cervical disc height decrease measured from radiographs is unclear. Methods: The MRI classification of degeneration was based on nucleus signal, prolaps identification and bone marrow signal. Two neuro-radiologists evaluated the MR-images independently in a blinded fashion. The radiographic disc height measurements were done by a new computer-assisted method compensating for image distortion and permitting comparison with normal level-, age- and gender-appropriate disc height. Results/conclusions: 1.Progressing disc degeneration classified from MRI is on average significantly associated with a decrease of disc height as measured from radiographs. Within each MRI defined category of degeneration measured disc heights, however, scatter in a wide range. 2.The inter-observer agreement between two neuro-radiologists in both defining degeneration and disc height by MRI was only moderate. Studies addressing questions related to cervical disc degeneration should take this into consideration

Degeneration and height of cervical discs classified from MRI compared with precise height measurements from radiographs

Energy Technology Data Exchange (ETDEWEB)

Kolstad, Frode [National Centre of Spinal Disorders, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway)]. E-mail: frode.kolstad@medisin.ntnu.no; Myhr, Gunnar [Department of Radiology, University Hospital of Trondheim, 7006 Trondheim (Norway); Kvistad, Kjell Arne [Department of Radiology, University Hospital of Trondheim, 7006 Trondheim (Norway); Nygaard, Oystein P. [National Centre of Spinal Disorders, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway); Leivseth, Gunnar [Department of Neuromedicine, Faculty of Medicine, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway)

2005-09-01

Study design: Descriptive study comparing MRI classifications with measurements from radiographs. Objectives: 1.Define the relationship between MRI classified cervical disc degeneration and objectively measured disc height. 2.Assess the level of inter- and intra-observer errors using MRI in defining cervical disc degeneration. Summary of background data: Cervical spine degeneration has been defined radiologically by loss of disc height, decreased disc and bone marrow signal intensity and disc protrusion/herniation on MRI. The intra- and inter-observer error using MRI in defining cervical degeneration influences data interpretation. Few previous studies have addressed this source of error. The relation and time sequence between cervical disc degeneration classified by MRI and cervical disc height decrease measured from radiographs is unclear. Methods: The MRI classification of degeneration was based on nucleus signal, prolaps identification and bone marrow signal. Two neuro-radiologists evaluated the MR-images independently in a blinded fashion. The radiographic disc height measurements were done by a new computer-assisted method compensating for image distortion and permitting comparison with normal level-, age- and gender-appropriate disc height. Results/conclusions: 1.Progressing disc degeneration classified from MRI is on average significantly associated with a decrease of disc height as measured from radiographs. Within each MRI defined category of degeneration measured disc heights, however, scatter in a wide range. 2.The inter-observer agreement between two neuro-radiologists in both defining degeneration and disc height by MRI was only moderate. Studies addressing questions related to cervical disc degeneration should take this into consideration.

Remote determination of the velocity index and mean streamwise velocity profiles

Science.gov (United States)

Johnson, E. D.; Cowen, E. A.

2017-09-01

When determining volumetric discharge from surface measurements of currents in a river or open channel, the velocity index is typically used to convert surface velocities to depth-averaged velocities. The velocity index is given by, k=Ub/Usurf, where Ub is the depth-averaged velocity and Usurf is the local surface velocity. The USGS (United States Geological Survey) standard value for this coefficient, k = 0.85, was determined from a series of laboratory experiments and has been widely used in the field and in laboratory measurements of volumetric discharge despite evidence that the velocity index is site-specific. Numerous studies have documented that the velocity index varies with Reynolds number, flow depth, and relative bed roughness and with the presence of secondary flows. A remote method of determining depth-averaged velocity and hence the velocity index is developed here. The technique leverages the findings of Johnson and Cowen (2017) and permits remote determination of the velocity power-law exponent thereby, enabling remote prediction of the vertical structure of the mean streamwise velocity, the depth-averaged velocity, and the velocity index.

An antithetic variate to facilitate upper-stem height measurements for critical height sampling with importance sampling

Science.gov (United States)

Thomas B. Lynch; Jeffrey H. Gove

2013-01-01

Critical height sampling (CHS) estimates cubic volume per unit area by multiplying the sum of critical heights measured on trees tallied in a horizontal point sample (HPS) by the HPS basal area factor. One of the barriers to practical application of CHS is the fact that trees near the field location of the point-sampling sample point have critical heights that occur...

Effects of balance ability and handgrip height on kinematics of the gait, torso, and pelvis in elderly women using a four-wheeled walker.

Science.gov (United States)

Choi, Hyuk-Jae; Ko, Chang-Yong; Kang, Sungjae; Ryu, Jeicheong; Mun, Museong; Jeon, Hye-Seon

2015-02-01

Numerous elderly individuals use the four-wheeled walker (FWW) as a gait-assistive device. The walker's handgrip height is important for correct use. However, few clinical studies have investigated the biomechanical effects of the FWW's handgrip height on balance. Therefore, the present study assessed kinematic features of the gait, torso and pelvis during use of the FWW at two levels of handgrip height (48% vs 55% of the subject's height) while assessing balance in older adults. A total of 20 older adults were allocated into two groups according to the Berg Balance Scale (BBS): good balance (GB; BBS≥46) versus poor balance (PB; BBS<45). Participants walked with the FWW at 48% or 55% handgrip height for 10 m. Our study showed that the double-support period and stance phase significantly increased at 55% handgrip height, but the swing phase significantly decreased in the GB group. In the PB group, velocity and stride length significantly increased at 55% handgrip height. Tilt angle of the torso in the GB group was significantly lower at 55% than at 48% handgrip height, but no differences were observed in the PB group. In the pelvis, initial contact and toe-off angles of tilt were lower in the GB group at 55% handgrip height, but no differences were observed in the PB group. These results showed that kinematic features of the gait, torso, and pelvis in older adults using the FWW might be dependent on the handgrip height of the FWW and the patient's balance. Additionally, greater than 48% of the body height might be appropriate for older adults with poor balance. © 2014 Japan Geriatrics Society.

Height perception influenced by texture gradient.

Science.gov (United States)

Tozawa, Junko

2012-01-01

Three experiments were carried out to examine whether a texture gradient influences perception of relative object height. Previous research implicated texture cues in judgments of object width, but similar influences have not been demonstrated for relative height. In this study, I evaluate a hypothesis that the projective ratio of the number of texture elements covered by the objects combined with the ratio of the retinal object heights determines percepts of relative object height. Density of texture background was varied: four density conditions ranged from no-texture to very dense texture. In experiments 1 and 2, participants judged the height of comparison bar compared to the standard bar positioned on no-texture or textured backgrounds. Results showed relative height judgments differed with texture manipulations, consistent with predictions from a hypothesised combination of the number of texture elements with retinal height (experiment 1), or partially consistent with this hypothesis (experiment 2). In experiment 2, variations in the position of a comparison object showed that comparisons located far from the horizon were judged more poorly than in other positions. In experiment 3 I examined distance perception; relative distance judgments were found to be also affected by textured backgrounds. Results are discussed in terms of Gibson's relational theory and distance calibration theory.

Improved boundary layer height measurement using a fuzzy logic method: Diurnal and seasonal variabilities of the convective boundary layer over a tropical station

Science.gov (United States)

Allabakash, S.; Yasodha, P.; Bianco, L.; Venkatramana Reddy, S.; Srinivasulu, P.; Lim, S.

2017-09-01

This paper presents the efficacy of a "tuned" fuzzy logic method at determining the height of the boundary layer using the measurements from a 1280 MHz lower atmospheric radar wind profiler located in Gadanki (13.5°N, 79°E, 375 mean sea level), India, and discusses the diurnal and seasonal variations of the measured convective boundary layer over this tropical station. The original fuzzy logic (FL) method estimates the height of the atmospheric boundary layer combining the information from the range-corrected signal-to-noise ratio, the Doppler spectral width of the vertical velocity, and the vertical velocity itself, measured by the radar, through a series of thresholds and rules, which did not prove to be optimal for our radar system and geographical location. For this reason the algorithm was tuned to perform better on our data set. Atmospheric boundary layer heights obtained by this tuned FL method, the original FL method, and by a "standard method" (that only uses the information from the range-corrected signal-to-noise ratio) are compared with those obtained from potential temperature profiles measured by collocated Global Positioning System Radio Sonde during years 2011 and 2013. The comparison shows that the tuned FL method is more accurate than the other methods. Maximum convective boundary layer heights are observed between 14:00 and 15:00 local time (LT = UTC + 5:30) for clear-sky days. These daily maxima are found to be lower during winter and postmonsoon seasons and higher during premonsoon and monsoon seasons, due to net surface radiation and convective processes over this region being more intense during premonsoon and monsoon seasons and less intense in winter and postmonsoon seasons.

Rotational Angles and Velocities During Down the Line and Diagonal Across Court Volleyball Spikes

Directory of Open Access Journals (Sweden)

Justin R. Brown

2014-05-01

Full Text Available The volleyball spike is an explosive movement that is frequently used to end a rally and earn a point. High velocity spikes are an important skill for a successful volleyball offense. Although the influence of vertical jump height and arm velocity on spiked ball velocity (SBV have been investigated, little is known about the relationship of shoulder and hip angular kinematics with SBV. Other sport skills, like the baseball pitch share similar movement patterns and suggest trunk rotation is important for such movements. The purpose of this study was to examine the relationship of both shoulder and hip angular kinematics with ball velocity during the volleyball spike. Methods: Fourteen Division I collegiate female volleyball players executed down the line (DL and diagonally across-court (DAC spikes in a laboratory setting to measure shoulder and hip angular kinematics and velocities. Each spike was analyzed using a 10 Camera Raptor-E Digital Real Time Camera System.  Results: DL SBV was significantly greater than for DAC, respectively (17.54±2.35 vs. 15.97±2.36 m/s, p<0.05.  The Shoulder Hip Separation Angle (S-HSA, Shoulder Angular Velocity (SAV, and Hip Angular Velocity (HAV were all significantly correlated with DAC SBV. S-HSA was the most significant predictor of DAC SBV as determined by regression analysis.  Conclusions: This study provides support for a relationship between a greater S-HSA and SBV. Future research should continue to 1 examine the influence of core training exercise and rotational skill drills on SBV and 2 examine trunk angular velocities during various types of spikes during play.

Development of an optimal velocity selection method with velocity obstacle

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Geuk; Oh, Jun Ho [KAIST, Daejeon (Korea, Republic of)

2015-08-15

The Velocity obstacle (VO) method is one of the most well-known methods for local path planning, allowing consideration of dynamic obstacles and unexpected obstacles. Typical VO methods separate a velocity map into a collision area and a collision-free area. A robot can avoid collisions by selecting its velocity from within the collision-free area. However, if there are numerous obstacles near a robot, the robot will have very few velocity candidates. In this paper, a method for choosing optimal velocity components using the concept of pass-time and vertical clearance is proposed for the efficient movement of a robot. The pass-time is the time required for a robot to pass by an obstacle. By generating a latticized available velocity map for a robot, each velocity component can be evaluated using a cost function that considers the pass-time and other aspects. From the output of the cost function, even a velocity component that will cause a collision in the future can be chosen as a final velocity if the pass-time is sufficiently long enough.

Height and Tilt Geometric Texture

DEFF Research Database (Denmark)

Andersen, Vedrana; Desbrun, Mathieu; Bærentzen, Jakob Andreas

2009-01-01

compromise between functionality and simplicity: it can efficiently handle and process geometric texture too complex to be represented as a height field, without having recourse to full blown mesh editing algorithms. The height-and-tilt representation proposed here is fully intrinsic to the mesh, making...

Final height and intrauterine growth retardation.

Science.gov (United States)

Tauber, Maïthé

2017-06-01

Approximately 10% of small for gestational age (SGA) children maintain a small body size throughout childhood and often into adult life with a decreased pubertal spurt. Growth hormone (GH) therapy increases short-term growth in a dose-dependent manner and adult height had now been well documented. Shorter children might benefit from a higher dose at start (50μg/kg/day). The response to GH treatment was similar for both preterm and term short SGA groups and the effect of GH treatment on adult height showed a wide variation in growth response. As a whole, mean adult height is higher than -2 SDS in 60% of patients and 70% reached an adult height in their target height with better results with higher doses and combined GnRH analog therapy in those who were short at onset of puberty. Copyright © 2017. Published by Elsevier Masson SAS.

Validity of a Simple Method for Measuring Force-Velocity-Power Profile in Countermovement Jump.

Science.gov (United States)

Jiménez-Reyes, Pedro; Samozino, Pierre; Pareja-Blanco, Fernando; Conceição, Filipe; Cuadrado-Peñafiel, Víctor; González-Badillo, Juan José; Morin, Jean-Benoît

2017-01-01

To analyze the reliability and validity of a simple computation method to evaluate force (F), velocity (v), and power (P) output during a countermovement jump (CMJ) suitable for use in field conditions and to verify the validity of this computation method to compute the CMJ force-velocity (F-v) profile (including unloaded and loaded jumps) in trained athletes. Sixteen high-level male sprinters and jumpers performed maximal CMJs under 6 different load conditions (0-87 kg). A force plate sampling at 1000 Hz was used to record vertical ground-reaction force and derive vertical-displacement data during CMJ trials. For each condition, mean F, v, and P of the push-off phase were determined from both force-plate data (reference method) and simple computation measures based on body mass, jump height (from flight time), and push-off distance and used to establish the linear F-v relationship for each individual. Mean absolute bias values were 0.9% (± 1.6%), 4.7% (± 6.2%), 3.7% (± 4.8%), and 5% (± 6.8%) for F, v, P, and slope of the F-v relationship (S Fv ), respectively. Both methods showed high correlations for F-v-profile-related variables (r = .985-.991). Finally, all variables computed from the simple method showed high reliability, with ICC >.980 and CV push-off distance, and jump height are known.

Challenges in Defining Tsunami Wave Height

Science.gov (United States)

Stroker, K. J.; Dunbar, P. K.; Mungov, G.; Sweeney, A.; Arcos, N. P.

2017-12-01

The NOAA National Centers for Environmental Information (NCEI) and co-located World Data Service for Geophysics maintain the global tsunami archive consisting of the historical tsunami database, imagery, and raw and processed water level data. The historical tsunami database incorporates, where available, maximum wave heights for each coastal tide gauge and deep-ocean buoy that recorded a tsunami signal. These data are important because they are used for tsunami hazard assessment, model calibration, validation, and forecast and warning. There have been ongoing discussions in the tsunami community about the correct way to measure and report these wave heights. It is important to understand how these measurements might vary depending on how the data were processed and the definition of maximum wave height. On September 16, 2015, an 8.3 Mw earthquake located 48 km west of Illapel, Chile generated a tsunami that was observed all over the Pacific region. We processed the time-series water level data for 57 tide gauges that recorded this tsunami and compared the maximum wave heights determined from different definitions. We also compared the maximum wave heights from the NCEI-processed data with the heights reported by the NOAA Tsunami Warning Centers. We found that in the near field different methods of determining the maximum tsunami wave heights could result in large differences due to possible instrumental clipping. We also found that the maximum peak is usually larger than the maximum amplitude (½ peak-to-trough), but the differences for the majority of the stations were Warning Centers. Since there is currently only one field in the NCEI historical tsunami database to store the maximum tsunami wave height, NCEI will consider adding an additional field for the maximum peak measurement.

Combined Treatment with Gonadotropin-releasing Hormone Analog and Anabolic Steroid Hormone Increased Pubertal Height Gain and Adult Height in Boys with Early Puberty for Height

OpenAIRE

Tanaka, Toshiaki; Naiki, Yasuhiro; Horikawa, Reiko

2012-01-01

Twenty-one boys with a height of 135 cm or less at onset of puberty were treated with a combination of GnRH analog and anabolic steroid hormone, and their pubertal height gain and adult height were compared with those of untreated 29 boys who enter puberty below 135 cm. The mean age at the start of treatment with a GnRH analog, leuprorelin acetate depot (Leuplin?) was 12.3 yr, a mean of 1.3 yr after the onset of puberty, and GnRH analog was administered every 3 to 5 wk thereafter for a mean d...

Development Characteristics of Velocity Transports in An Isothermal Heated Drag-Reducing Surfactant Solution Flow

Science.gov (United States)

Zhang, Hongxia; Wang, Dezhong; Chen, Hanping; Wang, Yanping

2007-06-01

The development characteristics, turbulence transports for stresses and kinetic energy of a cetyltrimethyl ammonium chloride (CTAC) surfactant solution for a two-dimensional channel flow have been experimentally investigated. Time mean velocity and fluctuating velocity are measured using a Phase Doppler Anemometry (PDA) at the Reynolds number 1.78×104 and isothermal heated temperature 31°C. Although mean velocity profiles at three cross sections show that the fluid is almost fully developed, the peak location of fluctuating intensity for the CTAC solution is slightly away from the wall downstream from the fluid and the peak location of fluctuating intensity is observed at far away from the wall than that of water. The location where the velocity gradient has its maximum, the fluctuating intensity does not get the high value. The elastic shear stress contribution to the total shear stress is 15 percents to 36 percents and it gets to the maximum near to the wall. The surfactant elastic shear stress is almost a liner function of the height of the channel, which means that the elastic stress contribution of the different cross locations is approximately the same. The fluctuating surfactant stress work is negative and the fluctuating elastic shear stresses produce rather than dissipate kinetic energy.

Height predicts jealousy differently for men and women

NARCIS (Netherlands)

Buunk, Abraham P.; Park, Justin H.; Zurriaga, Rosario; Klavina, Liga; Massar, Karlijn

Because male height is associated with attractiveness, dominance, and reproductive success, taller men may be less jealous. And because female height has a curvilinear relationship with health and reproductive success (with average-height females having the advantages), female height may have a

The association between adult attained height and sitting height with mortality in the European Prospective Investigation into Cancer and Nutrition (EPIC.

Directory of Open Access Journals (Sweden)

Norie Sawada

Full Text Available Adult height and sitting height may reflect genetic and environmental factors, including early life nutrition, physical and social environments. Previous studies have reported divergent associations for height and chronic disease mortality, with positive associations observed for cancer mortality but inverse associations for circulatory disease mortality. Sitting height might be more strongly associated with insulin resistance; however, data on sitting height and mortality is sparse. Using the European Prospective Investigation into Cancer and Nutrition study, a prospective cohort of 409,748 individuals, we examined adult height and sitting height in relation to all-cause and cause-specific mortality. Height was measured in the majority of participants; sitting height was measured in ~253,000 participants. During an average of 12.5 years of follow-up, 29,810 deaths (11,931 from cancer and 7,346 from circulatory disease were identified. Hazard ratios (HR with 95% confidence intervals (CI for death were calculated using multivariable Cox regression within quintiles of height. Height was positively associated with cancer mortality (men: HRQ5 vs. Q1 = 1.11, 95%CI = 1.00-1.24; women: HRQ5 vs. Q1 = 1.17, 95%CI = 1.07-1.28. In contrast, height was inversely associated with circulatory disease mortality (men: HRQ5 vs. Q1 = 0.63, 95%CI = 0.56-0.71; women: HRQ5 vs. Q1 = 0.81, 95%CI = 0.70-0.93. Although sitting height was not associated with cancer mortality, it was inversely associated with circulatory disease (men: HRQ5 vs. Q1 = 0.64, 95%CI = 0.55-0.75; women: HRQ5 vs. Q1 = 0.60, 95%CI = 0.49-0.74 and respiratory disease mortality (men: HRQ5 vs. Q1 = 0.45, 95%CI = 0.28-0.71; women: HRQ5 vs. Q1 = 0.60, 95%CI = 0.40-0.89. We observed opposing effects of height on cancer and circulatory disease mortality. Sitting height was inversely associated with circulatory disease and respiratory disease mortality.

Experimental investigations on frictional resistance and velocity distribution of rough wall with regularly distributed triangular ribs

International Nuclear Information System (INIS)

Motozawa, Masaaki; Ito, Takahiro; Iwamoto, Kaoru; Kawashima, Hideki; Ando, Hirotomo; Senda, Tetsuya; Tsuji, Yoshiyuki; Kawaguchi, Yasuo

2013-01-01

Highlights: • Flow over the regularly distributed triangular ribs was investigated. • Simultaneous measurement of flow resistance and velocity profile was performed. • Flow resistance was measured directly and velocity profile was measured by LDV. • Flow resistance was estimated by the information of the velocity field. • Estimated flow resistance has good agreement with the measured flow resistance. -- Abstract: The relationship between the flow resistance of a turbulent flow over triangular ribs regularly distributed on a wall surface and the velocity distribution around the ribs was investigated experimentally. A concentric cylinder device composed of an inner test cylinder and an outer cylinder was employed to measure the flow resistance using the torque of the shaft of the inner cylinder and the velocity distribution of the flow around a rib by laser Doppler velocimetry (LDV) simultaneously. We prepared four inner test cylinders having 4, 8, 12 and 16 triangular ribs on the surface with the same interval between them. Each rib had an isosceles right triangle V-shape and a height of 2 mm. To investigate the relationship between flow resistance and velocity distribution, we estimated the frictional drag and pressure drag acting on the surface of the ribs separately using the velocity distribution. Therefore, we could also estimate the total flow resistance using the velocity distribution. As a result of the experiment, the flow resistance and the attachment point downstream of the rib were shown to depend on the distance between ribs. Moreover, the flow resistance estimated using the velocity distribution had good agreement with the flow resistance measured using the torque of the inner cylinder

Biomechanics of Thoracolumbar Burst and Chance-Type Fractures during Fall from Height

Science.gov (United States)

Ivancic, Paul C.

2014-01-01

Study Design In vitro biomechanical study. Objective To investigate the biomechanics of thoracolumbar burst and Chance-type fractures during fall from height. Methods Our model consisted of a three-vertebra human thoracolumbar specimen (n = 4) stabilized with muscle force replication and mounted within an impact dummy. Each specimen was subjected to a single fall from an average height of 2.1 m with average velocity at impact of 6.4 m/s. Biomechanical responses were determined using impact load data combined with high-speed movie analyses. Injuries to the middle vertebra of each spinal segment were evaluated using imaging and dissection. Results Average peak compressive forces occurred within 10 milliseconds of impact and reached 40.3 kN at the ground, 7.1 kN at the lower vertebra, and 3.6 kN at the upper vertebra. Subsequently, average peak flexion (55.0 degrees) and tensile forces (0.7 kN upper vertebra, 0.3 kN lower vertebra) occurred between 43.0 and 60.0 milliseconds. The middle vertebra of all specimens sustained pedicle and endplate fractures with comminution, bursting, and reduced height of its vertebral body. Chance-type fractures were observed consisting of a horizontal split fracture through the laminae and pedicles extending anteriorly through the vertebral body. Conclusions We hypothesize that the compression fractures of the pedicles and vertebral body together with burst fracture occurred at the time of peak spinal compression, 10 milliseconds. Subsequently, the onset of Chance-type fracture occurred at 20 milliseconds through the already fractured and weakened pedicles and vertebral body due to flexion-distraction and a forward shifting spinal axis of rotation. PMID:25083357

Genetically Determined Height and Coronary Artery Disease

NARCIS (Netherlands)

Nelson, Christopher P.; Hamby, Stephen E.; Saleheen, Danish; Hopewell, Jenna C.; Zeng, Lingyao; Assimes, Themistocles L.; Kanoni, Stavroula; Willenborg, Christina; Burgess, Stephen; Amouyel, Phillipe; Anand, Sonia; Blankenberg, Stefan; Boehm, Bernhard O.; Clarke, Robert J.; Collins, Rory; Dedoussis, George; Farrall, Martin; Franks, Paul W.; Groop, Leif; Hall, Alistair S.; Hamsten, Anders; Hengstenberg, Christian; Hovingh, G. Kees; Ingelsson, Erik; Kathiresan, Sekar; Kee, Frank; König, Inke R.; Kooner, Jaspal; Lehtimäki, Terho; März, Winifred; McPherson, Ruth; Metspalu, Andres; Nieminen, Markku S.; O'Donnell, Christopher J.; Palmer, Colin N. A.; Peters, Annette; Perola, Markus; Reilly, Muredach P.; Ripatti, Samuli; Roberts, Robert; Salomaa, Veikko; Shah, Svati H.; Schreiber, Stefan; Siegbahn, Agneta; Thorsteinsdottir, Unnur; Veronesi, Giovani; Wareham, Nicholas; Willer, Cristen J.; Zalloua, Pierre A.; Erdmann, Jeanette

2015-01-01

BACKGROUND The nature and underlying mechanisms of an inverse association between adult height and the risk of coronary artery disease (CAD) are unclear. METHODS We used a genetic approach to investigate the association between height and CAD, using 180 height-associated genetic variants. We tested

The effect of ratio between rigid plant height and water depth on the manning’s coefficient in open channel

Science.gov (United States)

Rizalihadi, M.; Ziana; Shaskia, Nina; Asharly, H.

2018-05-01

One of the important factors in channel dimension is the Manning’s coefficient ( n ). This coefficient is influenced not only by the channel roughness but also by the presence of plants in the channel. The aim of the study is to see the effect of the ratio between the height of the rigid plant and water depth on the Manning’s coefficient (n) in open channel. The study was conducted in open channel with 15.5 m long, 0.5 m wide and 1.0 m high, in which at the center of the channel is planted with the rigid plants with a density of 42 plants/m2. The flow was run with a discharge of 0.013 m3/s at 6 ratios of Hplants/Hwater, namely: 0; 0.2; 0.6; 0.8; 1,0 and 1,2, to obtain the velocity and water profiles. Then the value of n is analyzed using Manning’s equation. The results showed that the mean velocity becomes decrease 17.81-34.01% as increase the ratio of Hplants/Hwater. This results in increasing n value to become 1.22-1.52 times compared to the unplanted channel ( no =0.038). So, it can be concluded that the ratio between the rigid plant’s height and water depth in the open channel can affect the value of Manning coefficient.

The height increments and BMI values of elite Central European children and youth in the second half of the 19th century.

Science.gov (United States)

Komlos, John

2006-01-01

Longitudinal height measurements on children and youth are very rare prior to the 20th century, as are BMI values. Growth increments and BMI values were determined among elite (select) Habsburg children and youth in the late 19th century and compared with other extant historical and contemporary data. Archival data on height and weight were collected for approximately 3500 students attending Habsburg Military schools. The students were measured once a year for 4 years. Because of the minimum height requirement, truncated regression was used in order to estimate height trends, but standard procedures were used to determine height increments and BMI values. Heights increased at most 0.9-1.6 cm between the birth cohorts of circa 1870s and 1900. These future officers were about the same size as their counterparts in the USA and France, but smaller than those attending the Royal Military Academy in Sandhurst, England, who were taller and probably the tallest in the world at the time. Height increments were markedly smaller than those experienced by German students in the 18th century after age 15. Central European BMI values were above those obtained in the USA in the 19th century but well below modern values. Although peak height velocity was experienced as early as ages 13 and 14, the height increments were very small compared even to other historical populations. The military academy selected mainly precocious applicants (with probably larger height increments at younger ages and smaller increments at older ages). BMI values in this sample were well below modern standards, but they were unexpectedly as high as those of contemporary US West Point cadets, a well nourished group. There were significant differences in the height of elites in Central Europe in the 19th century, pointing to substantial socio-economic inequality, but at least the elites were as well nourished as the US population.

Wuthering Heights

NARCIS (Netherlands)

Bronte, Emily

2005-01-01

Wuthering Heights tells the story of a romance between two youngsters: Catherine Earnshaw and an orphan boy, Heathcliff. After she rejects him for a boy from a better background he develops a lust for revenge that takes over his life. In attempting to win her back and destroy those he blames for his

Increased height standard deviation scores in response to growth hormone therapy to near-adult height in older children with delayed skeletal maturation: results from the ANSWER Program.

Science.gov (United States)

Ross, Judith L; Lee, Peter A; Gut, Robert; Germak, John

2015-01-01

A primary goal of recombinant human growth hormone therapy (GHT) in children is attaining normal adult height. In this study, children with growth hormone deficiency (GHD) (including isolated idiopathic growth hormone deficiency [IGHD] and multiple pituitary hormone deficiency [MPHD]), idiopathic short stature (ISS), and Turner syndrome (TS) were evaluated for near-adult height (NAH) and percent achieving NAH within the normal range after approximately 4 years of GHT. Data from the American Norditropin® Web-Enabled Research (ANSWER) Program were analyzed for NAH from age at treatment start (ATS) (i.e., referral age as defined by age at enrollment in the study) to last clinic visit using one of the following two criteria: 1) age ≥18 years, or 2) if male: ≥16 years and height velocity (HV) standard deviation score (HSDS) ≤ -2, and either GHD (n = 201), ISS (n = 19), or TS (n = 41). The main outcome measures included HSDS and corrected HSDS (HSDS-target HSDS) in response to GH treatment, and correlation of ATS with NAH HSDS. Mean (± SD) chronological and bone ages at baseline were 14.0 ± 2.1 years and 11.7 ± 2.0 years, respectively, and mean GHT duration was 4.0 ± 1.6 years. Mean HSDS (baseline to NAH; GHD: -2.7 to -1.0; ISS: -2.8 to -1.4; TS: -3.0 to -1.8) and mean corrected HSDS (baseline to NAH; GHD: -2.1 to -0.3; ISS: -2.1 to -0.6; TS: -1.8 to -0.6) increased across diagnostic indications. Percentages of patients reaching near-adult HSDS > -2 were GHD: 87.6%; ISS: 78.9%; TS: 65.8%. Significant negative correlations were found between ATS and NAH HSDS when analyzed by sex. Despite a relatively advanced childhood age, the majority of GH-treated patients attained mean near-adult HSDS within the normal range (HSDS > -2). Negative correlations of ATS with near-adult HSDS indicate that an earlier age at treatment start would likely have resulted in greater adult height achieved in both male and female patients.

Mixing height measurements from UHF wind profiling radar

Energy Technology Data Exchange (ETDEWEB)

Angevine, W.M.; Grimsdell, A.W. [CIRES, Univ. of Colorado, and NOAA Aeronomy Lab., Boulder, Colorado (United States)

1997-10-01

Mixing height in convective boundary layers can be detected by wind profiling radars (profilers) operating at or near 915 MHZ. We have made such measurements in a variety of settings including Alabama in 1992; Nova Scotia, Canada, during the North Atlantic Regional Experiment (NARE) 1993; Tennessee during the Southern Oxidant Study (SOS) 1994; near a 450 m tower in Wisconsin in 1995; and extensively in Illinois during the Flatland95, `96, and `97 experiments, as well as continuous operations at the Flatland Atmospheric Observatory. Profiler mixing height measurements, like all measurements, are subject to some limitations. The most important of these are due to rainfall, minimum height, and height resolution. Profilers are very sensitive to rain, which dominates the reflectivity and prevents the mixing height from being detected. Because the best height resolution is currently 60 m and the minimum height is 120-150 m AGL, the profiler is not suited for detecting mixing height in stable or nocturnal boundary layers. Problems may also arise in very dry or cold environments. (au) 12 refs.

Characterization of wind velocities in the upstream induction zone of a wind turbine using scanning continuous-wave lidars

DEFF Research Database (Denmark)

Simley, Eric; Angelou, Nikolas; Mikkelsen, Torben Krogh

2016-01-01

As a wind turbine generates power, induced velocities, lower than the freestream velocity, will be present upstream of the turbine due to perturbation of the flow by the rotor. In this study, the upstream induction zone of a 225kW horizontal axis Vestas V27 wind turbine located at the Danish...... Technical University’s Risø campus is investigated using a scanning Light Detection and Ranging (lidar) system. Three short-range continuous-wave “WindScanner” lidars are positioned in the field around the V27 turbine allowing detection of all three components of the wind velocity vectors within...... the induction zone. The time-averaged mean wind speeds at different locations in the upstream induction zone are measured by scanning a horizontal plane at hub height and a vertical plane centered at the middle of the rotor extending roughly 1.5 rotor diameters (D) upstream of the rotor. Turbulence statistics...

Auditory velocity discrimination in the horizontal plane at very high velocities.

Science.gov (United States)

Frissen, Ilja; Féron, François-Xavier; Guastavino, Catherine

2014-10-01

We determined velocity discrimination thresholds and Weber fractions for sounds revolving around the listener at very high velocities. Sounds used were a broadband white noise and two harmonic sounds with fundamental frequencies of 330 Hz and 1760 Hz. Experiment 1 used velocities ranging between 288°/s and 720°/s in an acoustically treated room and Experiment 2 used velocities between 288°/s and 576°/s in a highly reverberant hall. A third experiment addressed potential confounds in the first two experiments. The results show that people can reliably discriminate velocity at very high velocities and that both thresholds and Weber fractions decrease as velocity increases. These results violate Weber's law but are consistent with the empirical trend observed in the literature. While thresholds for the noise and 330 Hz harmonic stimulus were similar, those for the 1760 Hz harmonic stimulus were substantially higher. There were no reliable differences in velocity discrimination between the two acoustical environments, suggesting that auditory motion perception at high velocities is robust against the effects of reverberation. Copyright © 2014 Elsevier B.V. All rights reserved.

Fluctuations in Schottky barrier heights

International Nuclear Information System (INIS)

Mahan, G.D.

1984-01-01

A double Schottky barrier is often formed at the grain boundary in polycrystalline semiconductors. The barrier height is shown to fluctuate in value due to the random nature of the impurity positions. The magnitude of the fluctuations is 0.1 eV, and the fluctuations cause the barrier height measured by capacitance to differ from the one measured by electrical conductivity

14 CFR 27.87 - Height-speed envelope.

Science.gov (United States)

2010-01-01

... applicable power failure condition in paragraph (b) of this section, a limiting height-speed envelope must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Height-speed envelope. 27.87 Section 27.87... STANDARDS: NORMAL CATEGORY ROTORCRAFT Flight Performance § 27.87 Height-speed envelope. (a) If there is any...

Birth order progressively affects childhood height.

Science.gov (United States)

Savage, Tim; Derraik, José G B; Miles, Harriet L; Mouat, Fran; Cutfield, Wayne S; Hofman, Paul L

2013-09-01

There is evidence suggesting that first-born children and adults are anthropometrically different to later-borns. Thus, we aimed to assess whether birth order was associated with changes in growth and metabolism in childhood. We studied 312 healthy prepubertal children: 157 first-borns and 155 later-borns. Children were aged 3-10 years, born 37-41 weeks gestation, and of birth weight appropriate-for-gestational-age. Clinical assessments included measurement of children's height, weight, fasting lipid and hormonal profiles and DEXA-derived body composition. First-borns were taller than later-borns (P < 0·0001), even when adjusted for parents' heights (0·31 vs 0·03 SDS; P = 0·001). There was an incremental height decrease with increasing birth order, so that first-borns were taller than second-borns (P < 0·001), who were in turn taller than third-borns (P = 0·007). Further, among sibling pairs both height SDS (P = 0·009) and adjusted height SDS (P < 0·0001) were lower in second- vs first-born children. Consistent with differences in stature, first- (P = 0·043) and second-borns (P = 0·003) had higher IGF-I concentrations than third-borns. Both first- (P < 0·001) and second-borns (P = 0·004) also had reduced abdominal adiposity (lower android fat to gynoid fat ratio) when compared with third-borns. Other parameters of adiposity and blood lipids were unaffected by birth order. First-borns were taller than later-born children, with an incremental height reduction from first to third birth order. These differences were present after correction for genetic height, and associated to some extent with alterations in plasma IGF-I. Our findings strengthen the evidence that birth order is associated with phenotypic changes in childhood. © 2013 John Wiley & Sons Ltd.

An analysis of the relationship between bodily injury severity and fall height in victims of fatal falls from height

Directory of Open Access Journals (Sweden)

Grzegorz Teresiński

2017-03-01

Full Text Available Aim of the study : One of the basic issues discussed in forensic literature regarding falls from a height is determination of fall heights and differentiation between suicidal and accidental falls. The aim of the study was to verify the usefulness of the available methods for the purposes of forensic expertises. Material and methods : The study encompassed fatalities of falls from a height whose autopsies were performed in the Department of Forensic Medicine in Lublin. Results : Similarly to other authors, the severity of injuries was assessed using the Abbreviated Injury Scale (AIS and injury severity score (ISS. The study findings demonstrated a statistically significant correlation between the fall height and the severity of injuries according to ISS and a statistically significant difference in fall heights between the groups of accidents and suicides.

Introducing a novel gravitation-based high-velocity compaction analysis method for pharmaceutical powders.

Science.gov (United States)

Tanner, Timo; Antikainen, Osmo; Ehlers, Henrik; Yliruusi, Jouko

2017-06-30

With modern tableting machines large amounts of tablets are produced with high output. Consequently, methods to examine powder compression in a high-velocity setting are in demand. In the present study, a novel gravitation-based method was developed to examine powder compression. A steel bar is dropped on a punch to compress microcrystalline cellulose and starch samples inside the die. The distance of the bar is being read by a high-accuracy laser displacement sensor which provides a reliable distance-time plot for the bar movement. In-die height and density of the compact can be seen directly from this data, which can be examined further to obtain information on velocity, acceleration and energy distribution during compression. The energy consumed in compact formation could also be seen. Despite the high vertical compression speed, the method was proven to be cost-efficient, accurate and reproducible. Copyright © 2017 Elsevier B.V. All rights reserved.

A Simple Method for Assessing Upper-Limb Force-Velocity Profile in Bench Press.

Science.gov (United States)

Rahmani, Abderrahmane; Samozino, Pierre; Morin, Jean-Benoit; Morel, Baptiste

2018-02-01

To analyze the reliability and validity of a field computation method based on easy-to-measure data to assess the mean force ([Formula: see text]) and velocity ([Formula: see text]) produced during a ballistic bench-press movement and to verify that the force-velocity profile (F-v) obtained with multiple loaded trials is accurately described. Twelve participants performed ballistic bench presses against various lifted mass from 30% to 70% of their body mass. For each trial, [Formula: see text] and [Formula: see text] were determined from an accelerometer (sampling rate 500 Hz; reference method) and a simple computation method based on upper-limb mass, barbell flight height, and push-off distance. These [Formula: see text] and [Formula: see text] data were used to establish the F-v relationship for each individual and method. A strong to almost perfect reliability was observed between the 2 trials (ICC > .90 for [Formula: see text] and .80 for [Formula: see text], CV%  .80, P push-off distance).

Superconducting RF for Low-Velocity and Intermediate-Velocity Beams

CERN Document Server

Grimm, Terry L

2005-01-01

Existing superconducting radio frequency (SRF) linacs are used to accelerate ions (protons through uranium) with velocities less than about 15% the speed of light, or electrons with velocities approximately equal to the speed of light. In the last ten years, prototype SRF cavities have completely covered the remaining range of velocities. They have demonstrated that SRF linacs will be capable of accelerating electrons from rest up to the speed of light, and ions from less than 1% up to the speed of light. When the Spallation Neutron Source is operational, SRF ion linacs will have covered the full range of velocities except for v/c ~ 0.15 to v/c ~ 0.5. A number of proposed projects (RIA, EURISOL) would span the latter range of velocities. Future SRF developments will have to address the trade-offs associated with a number of issues, including high gradient operation, longitudinal and transverse acceptance, microphonics, Lorentz detuning, operating temperature, cryogenic load, number of gaps or cells per cavity...

Height and Breast Cancer Risk

DEFF Research Database (Denmark)

Zhang, Ben; Shu, Xiao-Ou; Delahanty, Ryan J

2015-01-01

BACKGROUND: Epidemiological studies have linked adult height with breast cancer risk in women. However, the magnitude of the association, particularly by subtypes of breast cancer, has not been established. Furthermore, the mechanisms of the association remain unclear. METHODS: We performed a meta......-analysis to investigate associations between height and breast cancer risk using data from 159 prospective cohorts totaling 5216302 women, including 113178 events. In a consortium with individual-level data from 46325 case patients and 42482 control patients, we conducted a Mendelian randomization analysis using...... a genetic score that comprised 168 height-associated variants as an instrument. This association was further evaluated in a second consortium using summary statistics data from 16003 case patients and 41335 control patients. RESULTS: The pooled relative risk of breast cancer was 1.17 (95% confidence...

Comparison of Power, Velocity and Force Parameters during Loaded Squat Jump Exercise in the Handball and Arm Wrestling Players

Science.gov (United States)

Can, Ibrahim

2017-01-01

The purpose of this study was to compare power, velocity and force parameters during loaded squat jump (SJ) exercise in the handball and arm wrestling players. In accordance with this purpose, ten arm wrestling athletes from the Turkish National Team (age: 20,7 ± 3,05 years; height: 175,2 ± 5,55 cm; weight: 71,7 ± 8,17 kg) who had ranks in…

Critical velocities in He II for independently varied superfluid and normal fluid velocities

International Nuclear Information System (INIS)

Baehr, M.L.

1984-01-01

Experiments were performed to measure the critical velocity in pure superflow and compare to the theoretical prediction; to measure the first critical velocity for independently varied superfluid and normal fluid velocities; and to investigate the propagation of the second critical velocity from the thermal counterflow line through the V/sub n/,-V/sub s/ quadrant. The experimental apparatus employed a thermal counterflow heater to adjust the normal fluid velocity, a fountain pump to vary the superfluid velocity, and a level sensing capacitor to measure the superfluid velocity. The results of the pure superfluid critical velocity measurements indicate that this velocity is temperature independent contrary to Schwarz's theory. It was found that the first critical velocity for independently varied V/sub n/ and V/sub s/ could be described by a linear function of V/sub n/ and was otherwise temperature independent. It was found that the second critical velocity could only be distinguished near the thermal counterflow line

Mean Velocity vs. Mean Propulsive Velocity vs. Peak Velocity: Which Variable Determines Bench Press Relative Load With Higher Reliability?

Science.gov (United States)

García-Ramos, Amador; Pestaña-Melero, Francisco L; Pérez-Castilla, Alejandro; Rojas, Francisco J; Gregory Haff, G

2018-05-01

García-Ramos, A, Pestaña-Melero, FL, Pérez-Castilla, A, Rojas, FJ, and Haff, GG. Mean velocity vs. mean propulsive velocity vs. peak velocity: which variable determines bench press relative load with higher reliability? J Strength Cond Res 32(5): 1273-1279, 2018-This study aimed to compare between 3 velocity variables (mean velocity [MV], mean propulsive velocity [MPV], and peak velocity [PV]): (a) the linearity of the load-velocity relationship, (b) the accuracy of general regression equations to predict relative load (%1RM), and (c) the between-session reliability of the velocity attained at each percentage of the 1-repetition maximum (%1RM). The full load-velocity relationship of 30 men was evaluated by means of linear regression models in the concentric-only and eccentric-concentric bench press throw (BPT) variants performed with a Smith machine. The 2 sessions of each BPT variant were performed within the same week separated by 48-72 hours. The main findings were as follows: (a) the MV showed the strongest linearity of the load-velocity relationship (median r = 0.989 for concentric-only BPT and 0.993 for eccentric-concentric BPT), followed by MPV (median r = 0.983 for concentric-only BPT and 0.980 for eccentric-concentric BPT), and finally PV (median r = 0.974 for concentric-only BPT and 0.969 for eccentric-concentric BPT); (b) the accuracy of the general regression equations to predict relative load (%1RM) from movement velocity was higher for MV (SEE = 3.80-4.76%1RM) than for MPV (SEE = 4.91-5.56%1RM) and PV (SEE = 5.36-5.77%1RM); and (c) the PV showed the lowest within-subjects coefficient of variation (3.50%-3.87%), followed by MV (4.05%-4.93%), and finally MPV (5.11%-6.03%). Taken together, these results suggest that the MV could be the most appropriate variable for monitoring the relative load (%1RM) in the BPT exercise performed in a Smith machine.

Experimental investigation on effect of inlet velocity ratios for 3-D temperature fluctuation caused by coaxial-jet flow

International Nuclear Information System (INIS)

Cao Qiong; Lu Daogang; Zhang Pan; Shi Wenbo; Tian Lu

2012-01-01

An experiment was performed to study the effect of inlet velocity ratios for 3-D temperature fluctuation caused by coaxial-jet flows based on the 3-D temperature and 2-D velocity fields. The experiment results show that the mixing behavior is completed at the bottom of test section in R<1 condition. The averaged temperatures at the bottom of the flow field are asymmetric in Rvelocity ratios, the gradients of cold fluid temperatures decrease in height direction, while those of hot fluid temperatures increase. In R>1 condition, the intensities of temperature fluctuations are less than those in R≤1 conditions. The strong temperature fluctuations occur in the regions between the hot and cold flow, as well as between the hot flow and environmental flow in this case. The frequencies of temperature fluctuations are less than 7 Hz. (authors)

Evolutionary perspectives on human height variation

NARCIS (Netherlands)

Stulp, Gert; Barrett, Louise

Human height is a highly variable trait, both within and between populations, has a high heritability, and influences the manner in which people behave and are treated in society. Although we know much about human height, this information has rarely been brought together in a comprehensive,

The association between adult attained height and sitting height with mortality in the European prospective investigation into cancer and nutrition (EPIC)

NARCIS (Netherlands)

Sawada, Norie; Wark, Petra A.; Merritt, Melissa A.; Tsugane, Shoichiro; Ward, Heather A.; Rinaldi, Sabina; Weiderpass, Elisabete; Dartois, Laureen; His, Mathilde; Boutron-Ruault, Marie Christine; Turzanski-Fortner, Renée; Kaaks, Rudolf; Overvad, Kim; Redondo, María Luisa; Travier, Noemie; Molina-Portillo, Elena; Dorronsoro, Miren; Cirera, Lluis; Ardanaz, Eva; Perez-Cornago, Aurora; Trichopoulou, Antonia; Lagiou, Pagona; Valanou, Elissavet; Masala, Giovanna; Pala, Valeria; Peeters, Petra H M; Van Der Schouw, Yvonne T.; Melander, Olle; Manjer, Jonas; Silva, Marisa Da; Skeie, Guri; Tjønneland, Anne; Olsen, Anja; Gunter, Marc J.; Riboli, Elio; Cross, Amanda J.

2017-01-01

Adult height and sitting height may reflect genetic and environmental factors, including early life nutrition, physical and social environments. Previous studies have reported divergent associations for height and chronic disease mortality, with positive associations observed for cancer mortality

Visual guidance of forward flight in hummingbirds reveals control based on image features instead of pattern velocity.

Science.gov (United States)

Dakin, Roslyn; Fellows, Tyee K; Altshuler, Douglas L

2016-08-02

Information about self-motion and obstacles in the environment is encoded by optic flow, the movement of images on the eye. Decades of research have revealed that flying insects control speed, altitude, and trajectory by a simple strategy of maintaining or balancing the translational velocity of images on the eyes, known as pattern velocity. It has been proposed that birds may use a similar algorithm but this hypothesis has not been tested directly. We examined the influence of pattern velocity on avian flight by manipulating the motion of patterns on the walls of a tunnel traversed by Anna's hummingbirds. Contrary to prediction, we found that lateral course control is not based on regulating nasal-to-temporal pattern velocity. Instead, birds closely monitored feature height in the vertical axis, and steered away from taller features even in the absence of nasal-to-temporal pattern velocity cues. For vertical course control, we observed that birds adjusted their flight altitude in response to upward motion of the horizontal plane, which simulates vertical descent. Collectively, our results suggest that birds avoid collisions using visual cues in the vertical axis. Specifically, we propose that birds monitor the vertical extent of features in the lateral visual field to assess distances to the side, and vertical pattern velocity to avoid collisions with the ground. These distinct strategies may derive from greater need to avoid collisions in birds, compared with small insects.

Diffraction imaging and velocity analysis using oriented velocity continuation

KAUST Repository

Decker, Luke

2014-08-05

We perform seismic diffraction imaging and velocity analysis by separating diffractions from specular reflections and decomposing them into slope components. We image slope components using extrapolation in migration velocity in time-space-slope coordinates. The extrapolation is described by a convection-type partial differential equation and implemented efficiently in the Fourier domain. Synthetic and field data experiments show that the proposed algorithm is able to detect accurate time-migration velocities by automatically measuring the flatness of events in dip-angle gathers.

Instrument modifications that produced reduced plate heights supercritical fluid chromatography.

Science.gov (United States)

Berger, Terry A

2016-04-29

The concept of peak fidelity was shown to be helpful in modeling tubing and detector cell dimensions. Connection tubing and flow cell variances were modeled to determine appropriate internal ID's, lengths, and volumes. A low dispersion plumbing configuration, based on these calculations, was assembled to replace the standard plumbing and produced the reported results. The modifications made were straightforward using commercially available parts. The full theoretical efficiency of a 3×100 mm column packed with 1.8 μm totally porous particles was achieved for the first time in supercritical fluid chromatography (SFC). Peak fidelity of >0.95 was maintained to below k=2. A reduced plate height as low as 1.87 was measured. Thus, true "ultra high performance" SFC was achieved, with the results a major improvement from all previous SFC reports. Since there were no efficiency losses, none could be attributed to thermal gradients caused by the expansion of the fluid over large pressure drops, under the conditions used. Similarly, changes in diffusion coefficients caused by significant decreases in density during expansion are apparently balanced by the increase in linear velocity, keeping the ratio between the diffusion coefficient and the linear velocity a constant. Changing modifier concentration to change retention was shown to not be a significant problem. All these issues have been a concern in the past. Diffusion coefficients, and viscosity data needs to be collected at high pressures before the actual limits of SFC can be discovered. Copyright © 2016 Elsevier B.V. All rights reserved.

Height, selected genetic markers and prostate cancer risk

DEFF Research Database (Denmark)

Lophatananon, Artitaya; Stewart-Brown, Sarah; Kote-Jarai, Zsofia

2017-01-01

Background:Evidence on height and prostate cancer risk is mixed, however, recent studies with large data sets support a possible role for its association with the risk of aggressive prostate cancer.Methods:We analysed data from the PRACTICAL consortium consisting of 6207 prostate cancer cases...... and 6016 controls and a subset of high grade cases (2480 cases). We explored height, polymorphisms in genes related to growth processes as main effects and their possible interactions.Results:The results suggest that height is associated with high-grade prostate cancer risk. Men with height >180 cm...... are at a 22% increased risk as compared to men with height prostate cancer risk. The aggregate scores of the selected variants identified a significantly increased risk of overall prostate cancer...

Differences in vertical jumping and mae-geri kicking velocity between international and national level karateka

Directory of Open Access Journals (Sweden)

Carlos Balsalobre-Fernández

2013-04-01

Full Text Available Aim: Lower limb explosive strength and mae-geri kicking velocity are fundamental in karate competition; although it is unclear whether these variables could differentiate the high-level athletes. The objective of this research is to analyze the differences in the mae-geri kicking velocity and the counter-movement jump (CMJ between a group of international top level karateka and another group of national-level karateka.Methods: Thirteen international-level karateka and eleven national-level karateka participated in the study. After a standard warm-up, CMJ height (in cm and mae-geri kicking velocity (in m/s was measured using an IR-platform and a high-speed camera, respectively.Results: Proceeding with MANCOVA to analyze the differences between groups controlling the effect of age, the results show that the international-level karateka demonstrated significantly higher levels of CMJ than national-level competitors (+22.1%, F = 9.47, p = 0.006, η2 = 0.311. There were no significant differences between groups in the mae-geri kicking velocity (+5,7%, F=0.80; p=0.38; η2=0.03.Conclusion: Our data shows, first, the importance of CMJ assessment as a tool to detect talent in karate and, second, that to achieve international-level in karate it may be important to increase CMJ levels to values ​​similar to those offered here.

14 CFR 29.1517 - Limiting height-speed envelope.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limiting height-speed envelope. 29.1517... Operating Limitations § 29.1517 Limiting height-speed envelope. For Category A rotorcraft, if a range of... following power failure, the range of heights and its variation with forward speed must be established...

Referencing geostrophic velocities using ADCP data Referencing geostrophic velocities using ADCP data

Directory of Open Access Journals (Sweden)

Isis Comas-Rodríguez

2010-06-01

Full Text Available Acoustic Doppler Current Profilers (ADCPs have proven to be a useful oceanographic tool in the study of ocean dynamics. Data from D279, a transatlantic hydrographic cruise carried out in spring 2004 along 24.5°N, were processed, and lowered ADCP (LADCP bottom track data were used to assess the choice of reference velocity for geostrophic calculations. The reference velocities from different combinations of ADCP data were compared to one another and a reference velocity was chosen based on the LADCP data. The barotropic tidal component was subtracted to provide a final reference velocity estimated by LADCP data. The results of the velocity fields are also shown. Further studies involving inverse solutions will include the reference velocity calculated here.

Free-surface velocity measurements using an optically recording velocity interferometer

International Nuclear Information System (INIS)

Lu Jianxin; Wang Zhao; Liang Jing; Shan Yusheng; Zhou Chuangzhi; Xiang Yihuai; Lu Ze; Tang Xiuzhang

2006-01-01

An optically recording velocity interferometer system (ORVIS) was developed for the free-surface velocity measurements in the equation of state experiments. The time history of free-surface velocity could be recorded by the electronic streak camera. In the experiments, ORVIS got a 179 ps time resolution, and a higher time resolution could be got by minimizing the delay time. The equation of state experiments were carried out on the high power excimer laser system called 'Heaven I' with laser wavelength of 248.4 nm, pulse duration of 25 ns and maximum energy 158 J. Free-surface velocity of 20 μm thick iron got 3.86 km/s with laser intensity of 6.24 x 10 11 W·cm -2 , and free-surface velocity of 100 μm thick aluminum with 100 μm CH foil at the front got 2.87 km/s with laser intensity 7.28 x 10 11 W·cm -2 . (authors)

Non-invasive aortic systolic pressure and pulse wave velocity estimation in a primary care setting: An in silico study.

Science.gov (United States)

Guala, Andrea; Camporeale, Carlo; Ridolfi, Luca; Mesin, Luca

2017-04-01

Everyday clinical cardiovascular evaluation is still largely based on brachial systolic and diastolic pressures. However, several clinical studies have demonstrated the higher diagnostic capacities of the aortic pressure, as well as the need to assess the aortic mechanical properties (e.g., by measuring the aortic pulse wave velocity). In order to fill this gap, we propose to exploit a set of easy-to-obtain physical characteristics to estimate the aortic pressure and pulse wave velocity. To this aim, a large population of virtual subjects is created by a validated mathematical model of the cardiovascular system. Quadratic regressive models are then fitted and statistically selected in order to obtain reliable estimations of the aortic pressure and pulse wave velocity starting from the knowledge of the subject age, height, weight, brachial pressure, photoplethysmographic measures and either electrocardiogram or phonocardiogram. The results are very encouraging and foster clinical studies aiming to apply a similar technique to a real population. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

On linear relationship between shock velocity and particle velocity

International Nuclear Information System (INIS)

Dandache, H.

1986-11-01

We attempt to derive the linear relationship between shock velocity U s and particle velocity U p from thermodynamic considerations, taking into account an ideal gas equation of state and a Mie-Grueneisen equation of state for solids. 23 refs

Entrapment investigations of water-droplet behavior in a hot tin melt with varying discharge velocities and orifices

International Nuclear Information System (INIS)

Froehlich, G.; Mueller, K.

1983-10-01

Experiments were performed in which water was pressed through a thermally isolated tube into a clyindrical crucible (diameter 5 cm, height 7,5 cm both measured inside) filled with molten tin (600 K). The diameter of the circular water outlet was varied from 0.5 up to 10 mm and the discharge velocity of the water was in the range of 0.05 up to 20 m/s. In the tin melt the water divides into single drops, which emerged on the melt surface, if an interaction between water and tin melt did not occur. The probability for an interaction increased in experiments with higher discharge velocities of the water and smaller diameters of the water outlet. In experiments with discharge velocities ≥ 5 m/s and outlet diameters ≤ 2 mm one or more interactions occured in each case. At these interactions of water drops entrapped in the tin melt (called entrapment interactions) a portion of the melt was ejected from the crucible. The moment of the interaction and the pulse of the force toward the crucible bottom were recorded. (orig.) [de

Soft computing methods for geoidal height transformation

Science.gov (United States)

Akyilmaz, O.; Özlüdemir, M. T.; Ayan, T.; Çelik, R. N.

2009-07-01

Soft computing techniques, such as fuzzy logic and artificial neural network (ANN) approaches, have enabled researchers to create precise models for use in many scientific and engineering applications. Applications that can be employed in geodetic studies include the estimation of earth rotation parameters and the determination of mean sea level changes. Another important field of geodesy in which these computing techniques can be applied is geoidal height transformation. We report here our use of a conventional polynomial model, the Adaptive Network-based Fuzzy (or in some publications, Adaptive Neuro-Fuzzy) Inference System (ANFIS), an ANN and a modified ANN approach to approximate geoid heights. These approximation models have been tested on a number of test points. The results obtained through the transformation processes from ellipsoidal heights into local levelling heights have also been compared.

The Sine Method: An Alternative Height Measurement Technique

Science.gov (United States)

Don C. Bragg; Lee E. Frelich; Robert T. Leverett; Will Blozan; Dale J. Luthringer

2011-01-01

Height is one of the most important dimensions of trees, but few observers are fully aware of the consequences of the misapplication of conventional height measurement techniques. A new approach, the sine method, can improve height measurement by being less sensitive to the requirements of conventional techniques (similar triangles and the tangent method). We studied...

Determination of the filtration velocities and mean velocity in ground waters using radiotracers

International Nuclear Information System (INIS)

Duran P, Oscar; Diaz V, Francisco; Heresi M, Nelida

1994-01-01

An experimental method to determine filtration, or, Darcy velocity and mean velocity in underground waters using radiotracers, is described. After selecting the most appropriate tracers, from 6 chemical compounds, to measure water velocity, a method to measure filtration velocity was developed. By fully labelling the water column with 2 radioisotopes, Br and tritium, almost identical values were obtained for the aquifer filtration velocity in the sounding S1. This value was 0.04 m/d. Field porosity was calculated at 11% and mean velocity at 0.37 m.d. With the filtration velocity value and knowing the hydraulic variation between the soundings S1 and S2 placed at 10 meters, field permeability was estimated at 2.4 x 10 m/s. (author)

Radial velocity asymmetries from jets with variable velocity profiles

International Nuclear Information System (INIS)

Cerqueira, A. H.; Vasconcelos, M. J.; Velazquez, P. F.; Raga, A. C.; De Colle, F.

2006-01-01

We have computed a set of 3-D numerical simulations of radiatively cooling jets including variabilities in both the ejection direction (precession) and the jet velocity (intermittence), using the Yguazu-a code. In order to investigate the effects of jet rotation on the shape of the line profiles, we also introduce an initial toroidal rotation velocity profile. Since the Yguazu-a code includes an atomic/ionic network, we are able to compute the emission coefficients for several emission lines, and we generate line profiles for the Hα, [O I]λ6300, [S II]λ6716 and [N II]λ6548 lines. Using initial parameters that are suitable for the DG Tau microjet, we show that the computed radial velocity shift for the medium-velocity component of the line profile as a function of distance from the jet axis is strikingly similar for rotating and non-rotating jet models

Relationship between Leg Mass, Leg Composition and Foot Velocity on Kicking Accuracy in Australian Football

Directory of Open Access Journals (Sweden)

Nicolas H. Hart, Jodie L. Cochrane, Tania Spiteri, Sophia Nimphius, Robert U. Newton

2016-06-01

Full Text Available Kicking a ball accurately over a desired distance to an intended target is arguably the most important skill to acquire in Australian Football. Therefore, understanding the potential mechanisms which underpin kicking accuracy is warranted. The aim of this study was to examine the relationship between leg mass, leg composition and foot velocity on kicking accuracy in Australian Football. Thirty-one Australian Footballers (n = 31; age: 22.1 ± 2.8 years; height: 1.81 ± 0.07 m; weight: 85.1 ± 13.0 kg; BMI: 25.9 ± 3.2 each performed ten drop punt kicks over twenty metres to a player target. Athletes were separated into accurate (n = 15 and inaccurate (n = 16 kicking groups. Leg mass characteristics were assessed using whole body DXA scans. Foot velocity was determined using a ten-camera optoelectronic, three-dimensional motion capture system. Interactions between leg mass and foot velocity evident within accurate kickers only (r = -0.670 to -0.701. Relative lean mass was positively correlated with kicking accuracy (r = 0.631, while no relationship between foot velocity and kicking accuracy was evident in isolation (r = -0.047 to -0.083. Given the evident importance of lean mass, and its interaction with foot velocity for accurate kickers; future research should explore speed-accuracy, impulse-variability, limb co-ordination and foot-ball interaction constructs in kicking using controlled with-in subject studies to examine the effects of resistance training and skill acquisition programs on the development of kicking accuracy.

Agreement between estimated and measured heights and weights ...

African Journals Online (AJOL)

index (BMI = kg/m2) and require accurate recording of a patient's height and weight.1. In reality, however, patients often cannot stand up straight for accurate height measurement, or are unable to step on a scale. In such cases, height and weight values are often obtained from the patient or their relatives, who either do not ...

Differences in anthropometric characteristics in relation to throwing velocity and competitive level in professional male team handball: a tool for talent profiling.

Science.gov (United States)

Fieseler, Georg; Hermassi, Souhail; Hoffmeyer, Birgit; Schulze, Stephan; Irlenbusch, Lars; Bartels, Thomas; Delank, Karl-Stefan; Laudner, Kevin G; Schwesig, René

2017-01-01

The primary aim of the study was to examine the anthropometric characteristics as well as throwing and sprinting performance of professional handball players classified by playing position and competition level. 21 male players (age: 25.2±5.1 years) from the first German handball league (FGL) and 34 male players (age: 26.1±4.1 years) from the third German handball league (TGL) were categorized as backs, pivots, wings and goalkeepers. Measurements included anthropometric data (height, mass and body mass index (BMI)), throwing and sprinting performance selected out of a complex handball test (HBCT), which was conducted twice (2 rounds). During the HBCT, the subjects performed two sprints (10, 20 m), two standing throws with run-up (ST) and four vertical jump throws (VJT) over a hurdle (20 cm) with and without precision for goal shot. The anthropometric data revealed a significantly (P=0.038 and η2=0.079) shorter body height for TGL than for FGL players. In the cohort of first league athletes the pivots were the tallest (1.98±0.04 m), backs in the third league showed the maximum body height (1.90±0.05 m). Regarding body mass, pivots were the heaviest players independent from the league membership. The FGL players showed a significantly (P0.10) higher throwing velocity in all type of throws. Body height was significantly related to ST (r=0.53) and VJT (r=0.52) in the first round of HBCT but only for the FGL athletes. Throwing velocity was also correlated with BMI (r=-0.50) among the TGL players. Substantial differences of body characteristics, throwing and sprinting performance between playing positions and competitive levels underline the importance of a careful scouting and position-specific training for professional handball players.

Estimation of seasonal atmospheric stability and mixing height by using different schemes

International Nuclear Information System (INIS)

Essa, K.S.M.; Embaby, M.; Mubarak, F.; Kamel, I.

2007-01-01

Different atmospheric stability schemes were used to characterize the plume growth (dispersion coefficients σ) in the lateral and vertical directions to determine the concentration distribution of pollutants through the PBL. The PBL is the region in which surface friction has a large effect on the mixing of pollutants. It is also suffer large fluctuation in temperature and wind and its depth (mixing depth) changes over a diurnal cycle. In this study, four months of surface meteorological parameters were used (to represent different seasons) to determine seasonal stability, classification. Five different stability schemes were estimated based on temperature gradient, standard deviation of the horizontal wind direction fluctuation, gradient and Bulk Richardson numbers and Monin-Obukhov length. Friction velocity, (u * ) for each stability scheme was estimated for characterizing the hourly, mixing height for each stability class. Also, plume rise was estimated for each stability class depending on the availability of meteorological parameters

Total body height estimation using sacrum height in Anatolian Caucasians: multidetector computed tomography-based virtual anthropometry

International Nuclear Information System (INIS)

Karakas, Hakki Muammer; Celbis, Osman; Harma, Ahmet; Alicioglu, Banu

2011-01-01

Estimation of total body height is a major step when a subject has to be identified from his/her skeletal structures. In the presence of decomposed skeletons and missing bones, estimation is usually based on regression equation for intact long bones. If these bones are fragmented or missing, alternative structures must be used. In this study, the value of sacrum height (SH) in total body height (TBH) estimation was investigated in a contemporary population of adult Anatolian Caucasians. Sixty-six men (41.6 ± 14.9 years) and 43 women (41.1 ± 14.2 years) were scanned with 64-row multidetector computed tomography (MDCT) to obtain high-resolution anthropometric data. SH of midsagittal sections was electronically measured. The technique and methodology were validated on a standard skeletal model. Sacrum height was 111.2 ± 12.6 mm (77-138 mm) in men and 104.7 ± 8.2 (89-125 mm) in women. The difference between the two sexes regarding SH was significant (p < 0.0001). SH did not significantly correlate with age in men, whereas the correlation was significant in women (p < 0.03). The correlation between SH and the stature was significant in men (r = 0.427, p < 0.0001) and was insignificant in women. For men the regression equation was [Stature = (0.306 x SH)+137.9] (r = 0.54, SEE = 56.9, p < 0.0001). Sacrum height is not susceptible to sex, or to age in men. In the presence of incomplete male skeletons, SH helps to determine the stature. This study is also one of the initial applications of MDCT in virtual anthropometric research. (orig.)

Total body height estimation using sacrum height in Anatolian Caucasians: multidetector computed tomography-based virtual anthropometry

Energy Technology Data Exchange (ETDEWEB)

Karakas, Hakki Muammer [Inonu University Medical Faculty, Turgut Ozal Medical Center, Department of Radiology, Malatya (Turkey); Celbis, Osman [Inonu University Medical Faculty Turgut Ozal Medical Center, Department of Forensic Medicine, Malatya (Turkey); Harma, Ahmet [Inonu University Medical Faculty Turgut Ozal Medical Center, Department of Orthopaedics and Traumatology, Malatya (Turkey); Alicioglu, Banu [Trakya University Medical Faculty, Department of Radiology, Edirne (Turkey); Trakya University Health Sciences Institute, Department of Anatomy, Edirne (Turkey)

2011-05-15

Estimation of total body height is a major step when a subject has to be identified from his/her skeletal structures. In the presence of decomposed skeletons and missing bones, estimation is usually based on regression equation for intact long bones. If these bones are fragmented or missing, alternative structures must be used. In this study, the value of sacrum height (SH) in total body height (TBH) estimation was investigated in a contemporary population of adult Anatolian Caucasians. Sixty-six men (41.6 {+-} 14.9 years) and 43 women (41.1 {+-} 14.2 years) were scanned with 64-row multidetector computed tomography (MDCT) to obtain high-resolution anthropometric data. SH of midsagittal sections was electronically measured. The technique and methodology were validated on a standard skeletal model. Sacrum height was 111.2 {+-} 12.6 mm (77-138 mm) in men and 104.7 {+-} 8.2 (89-125 mm) in women. The difference between the two sexes regarding SH was significant (p < 0.0001). SH did not significantly correlate with age in men, whereas the correlation was significant in women (p < 0.03). The correlation between SH and the stature was significant in men (r = 0.427, p < 0.0001) and was insignificant in women. For men the regression equation was [Stature = (0.306 x SH)+137.9] (r = 0.54, SEE = 56.9, p < 0.0001). Sacrum height is not susceptible to sex, or to age in men. In the presence of incomplete male skeletons, SH helps to determine the stature. This study is also one of the initial applications of MDCT in virtual anthropometric research. (orig.)

Propagation of the Semidiurnal Internal Tide: Phase Velocity Versus Group Velocity

Science.gov (United States)

Zhao, Zhongxiang

2017-12-01

The superposition of two waves of slightly different wavelengths has long been used to illustrate the distinction between phase velocity and group velocity. The first-mode M2 and S2 internal tides exemplify such a two-wave model in the natural ocean. The M2 and S2 tidal frequencies are 1.932 and 2 cycles per day, respectively, and their superposition forms a spring-neap cycle in the semidiurnal band. The spring-neap cycle acts like a wave, with its frequency, wave number, and phase being the differences of the M2 and S2 internal tides. The spring-neap cycle and energy of the semidiurnal internal tide propagate at the group velocity. Long-range propagation of M2 and S2 internal tides in the North Pacific is observed by satellite altimetry. Along a 3,400 km beam spanning 24°-54°N, the M2 and S2 travel times are 10.9 and 11.2 days, respectively. For comparison, it takes the spring-neap cycle 21.1 days to travel over this distance. Spatial maps of the M2 phase velocity, the S2 phase velocity, and the group velocity are determined from phase gradients of the corresponding satellite observed internal tide fields. The observed phase and group velocities agree with theoretical values estimated using the World Ocean Atlas 2013 annual-mean ocean stratification.

Reliability of the Load-Velocity Relationship Obtained Through Linear and Polynomial Regression Models to Predict the One-Repetition Maximum Load.

Science.gov (United States)

Pestaña-Melero, Francisco Luis; Haff, G Gregory; Rojas, Francisco Javier; Pérez-Castilla, Alejandro; García-Ramos, Amador

2017-12-18

This study aimed to compare the between-session reliability of the load-velocity relationship between (1) linear vs. polynomial regression models, (2) concentric-only vs. eccentric-concentric bench press variants, as well as (3) the within-participants vs. the between-participants variability of the velocity attained at each percentage of the one-repetition maximum (%1RM). The load-velocity relationship of 30 men (age: 21.2±3.8 y; height: 1.78±0.07 m, body mass: 72.3±7.3 kg; bench press 1RM: 78.8±13.2 kg) were evaluated by means of linear and polynomial regression models in the concentric-only and eccentric-concentric bench press variants in a Smith Machine. Two sessions were performed with each bench press variant. The main findings were: (1) first-order-polynomials (CV: 4.39%-4.70%) provided the load-velocity relationship with higher reliability than second-order-polynomials (CV: 4.68%-5.04%); (2) the reliability of the load-velocity relationship did not differ between the concentric-only and eccentric-concentric bench press variants; (3) the within-participants variability of the velocity attained at each %1RM was markedly lower than the between-participants variability. Taken together, these results highlight that, regardless of the bench press variant considered, the individual determination of the load-velocity relationship by a linear regression model could be recommended to monitor and prescribe the relative load in the Smith machine bench press exercise.

Modelling foot height and foot shape-related dimensions.

Science.gov (United States)

Xiong, Shuping; Goonetilleke, Ravindra S; Witana, Channa P; Lee Au, Emily Yim

2008-08-01

The application of foot anthropometry to design good-fitting footwear has been difficult due to the lack of generalised models. This study seeks to model foot dimensions so that the characteristic shapes of feet, especially in the midfoot region, can be understood. Fifty Hong Kong Chinese adults (26 males and 24 females) participated in this study. Their foot lengths, foot widths, ball girths and foot heights were measured and then evaluated using mathematical models. The results showed that there were no significant allometry (p > 0.05) effects of foot length on ball girth and foot width. Foot height showed no direct relationship with foot length. However, a normalisation with respect to foot length and foot height resulted in a significant relationship for both males and females with R(2) greater than 0.97. Due to the lack of a direct relationship between foot height and foot length, the current practice of grading shoes with a constant increase in height or proportionate scaling in response to foot length is less than ideal. The results when validated with other populations can be a significant way forward in the design of footwear that has an improved fit in the height dimension.

Imaging height fluctuations in free-standing graphene membranes

Science.gov (United States)

Dorsey, Kyle; Miskin, Marc; Barnard, Arthur; Rose, Peter; Cohen, Itai; McEuen, Paul

We present a technique based on multi-wavelength interference microscopy to measure the heights of observed ripples in free-standing graphene membranes. Graphene membranes released from a transparent substrate produce interference fringes when viewed in the reflection mode of an inverted microscope(Blees et. al. Nature 524 (7564): 204-207 (2015)). The fringes correspond to corrugation of the membrane as it floats near an interface. A single set of fringes is insufficient to uniquely determine the height profile, as a given fringe spacing can correspond to an increase or decrease in height by λ / 2 . Imaging at multiple wavelengths resolves the ambiguities in phase, and enables unique determination of the height profile of the membrane (Schilling et. al.Phys. Rev. E, 69:021901, 2004). We utilize this technique to map out the height fluctuations in free-standing graphene membranes to answer questions about fundamental mechanical properties of two-dimensional materials.

Footprint parameters as a measure of arch height.

Science.gov (United States)

Hawes, M R; Nachbauer, W; Sovak, D; Nigg, B M

1992-01-01

The human foot has frequently been categorized into arch height groups based upon analysis of footprint parameters. This study investigates the relationship between directly measured arch height and many of the footprint parameters that have been assumed to represent arch height. A total of 115 male subjects were measured and footprint parameters were calculated from digitized outlines. Correlation and regression analyses were used to determine the relationship between footprint measures and arch height. It may be concluded from the results that footprint parameters proposed in the literature (arch angle, footprint index, and arch index) and two further parameters suggested in this study (arch length index and truncated arch index) are invalid as a basis for prediction or categorization of arch height. The categorization of the human foot according to the footprint measures evaluated in this paper represent no more than indices and angles of the plantar surface of the foot itself.

Influence of micro-topography and crown characteristics on tree height estimations in tropical forests based on LiDAR canopy height models

Science.gov (United States)

Alexander, Cici; Korstjens, Amanda H.; Hill, Ross A.

2018-03-01

Tree or canopy height is an important attribute for carbon stock estimation, forest management and habitat quality assessment. Airborne Laser Scanning (ALS) based on Light Detection and Ranging (LiDAR) has advantages over other remote sensing techniques for describing the structure of forests. However, sloped terrain can be challenging for accurate estimation of tree locations and heights based on a Canopy Height Model (CHM) generated from ALS data; a CHM is a height-normalised Digital Surface Model (DSM) obtained by subtracting a Digital Terrain Model (DTM) from a DSM. On sloped terrain, points at the same elevation on a tree crown appear to increase in height in the downhill direction, based on the ground elevations at these points. A point will be incorrectly identified as the treetop by individual tree crown (ITC) recognition algorithms if its height is greater than that of the actual treetop in the CHM, which will be recorded as the tree height. In this study, the influence of terrain slope and crown characteristics on the detection of treetops and estimation of tree heights is assessed using ALS data in a tropical forest with complex terrain (i.e. micro-topography) and tree crown characteristics. Locations and heights of 11,442 trees based on a DSM are compared with those based on a CHM. The horizontal (DH) and vertical displacements (DV) increase with terrain slope (r = 0.47 and r = 0.54 respectively, p tree height are up to 16.6 m on slopes greater than 50° in our study area in Sumatra. The errors in locations (DH) and tree heights (DV) are modelled for trees with conical and spherical tree crowns. For a spherical tree crown, DH can be modelled as R sin θ, and DV as R (sec θ - 1). In this study, a model is developed for an idealised conical tree crown, DV = R (tan θ - tan ψ), where R is the crown radius, and θ and ψ are terrain and crown angles respectively. It is shown that errors occur only when terrain angle exceeds the crown angle, with the

Determination of velocity correction factors for real-time air velocity monitoring in underground mines.

Science.gov (United States)

Zhou, Lihong; Yuan, Liming; Thomas, Rick; Iannacchione, Anthony

2017-12-01

When there are installations of air velocity sensors in the mining industry for real-time airflow monitoring, a problem exists with how the monitored air velocity at a fixed location corresponds to the average air velocity, which is used to determine the volume flow rate of air in an entry with the cross-sectional area. Correction factors have been practically employed to convert a measured centerline air velocity to the average air velocity. However, studies on the recommended correction factors of the sensor-measured air velocity to the average air velocity at cross sections are still lacking. A comprehensive airflow measurement was made at the Safety Research Coal Mine, Bruceton, PA, using three measuring methods including single-point reading, moving traverse, and fixed-point traverse. The air velocity distribution at each measuring station was analyzed using an air velocity contour map generated with Surfer ® . The correction factors at each measuring station for both the centerline and the sensor location were calculated and are discussed.

A first comparison of irregularity and ion drift velocity measurements in the E-region

Directory of Open Access Journals (Sweden)

R. A. Makarevich

2006-09-01

Full Text Available E-region irregularity velocity measurements at large flow angles with the STARE Finland coherent VHF radar are considered in context of the ion and electron velocity data provided by the EISCAT tristatic radar system, CUTLASS Finland coherent HF radar, and IMAGE fluxgate magnetometers. The data have been collected during a special experiment on 27 March 2004 during which EISCAT was scanning between several E- and one F-region altitudes along the magnetic field line. Within the E-region, the EISCAT measurements at two altitudes of 110 and 115 km are considered while the electron velocity is inferred from the EISCAT ion velocity measurements at 278 km. The line-of-sight (l-o-s VHF velocity measured by STARE _{VHF los} is compared to the ion and electron velocity components (V_{i0 comp} and V_{e0 comp} along the STARE l-o-s direction. The comparison with V_{e0 comp} for the entire event shows that the measurements exhibit large scatter and small positive correlation. The correlation with V_{e0 comp} was substantial in the first half of the interval under study when V_{e0 comp} was larger in magnitude. The comparison with V_{i0 comp} at 110 and 115 km shows a considerable positive correlation, with VHF velocity being typically larger (smaller in magnitude than V_{i0 comp} at 110 km (115 km so that V_{VHF los} appears to be bounded by the ion velocity components at two altitudes. It is also demonstrated that the difference between V_{VHF los} and V_{i0 comp} at 110 km can be treated, in the first approximation, as a linear function of the effective backscatter height h_eff also counted from 110 km; h_eff varies in the range 108–114 km due to the altitude integration effects in the scattering cross-section. Our results are consistent with the notion that VHF

The Role of a Relative Age Effect in the 7th International Children’s Winter Games 2016 and the Influence of Biological Maturity Status on Selection

Science.gov (United States)

Müller, Lisa; Hildebrandt, Carolin; Raschner, Christian

2017-01-01

The aim of this study was to analyse the role of a relative age effect (RAE) and to investigate the influence of biological maturity status on the RAE at the 7th International Children`s Winter Games. The birth dates of all 572 participants (365 males, 207 females) were analysed, and the biological maturity status of 384 athletes (243 males, 141 females) was assessed by the age at peak height velocity (APHV) method. A RAE was present in the total sample (χ2 = 67.81; p < 0.001), and among both male (χ2 = 49.02; p < 0.001) and female athletes (χ2 = 37.00; p < 0.001) as well as for strength- (χ2 = 56.46; p < 0.001), endurance- (χ2 = 20.48; p = 0.039) and technique-related types of sports (χ2 = 20.48; p = 0.041). No significant differences in biological maturity status were present between the male athletes of single relative age quarters. Among the female athletes a significant difference was present (F = 5.94, p < 0.001); relatively younger female athletes had significantly lower values in the APHV, which indicated that they were maturing earlier. However, when dividing the athletes into normal, early and late maturing athletes, it could be seen that among the relatively younger athletes, hardly any late maturing athletes were present. These findings revealed that relatively younger athletes seemed to only have a chance for selection if they were early maturing, whereas relatively older athletes had an increased likelihood for selection independent of their biological maturity status. In the future, the relative age and the biological maturity status should be considered in the talent development system for various types of winter sport, to contribute to more fairness and to not discriminate against relatively younger and less mature athletes. Key points The relative age strongly influenced the participation rate at the 7th ICG in 2016. A highly significant RAE was present among male and female participants and among athletes of all three groups of sport

Velocity profile of water vapor inside a cavity with two axial inlets and two outlets

Science.gov (United States)

Guadarrama-Cetina, José; Ruiz Chavarría, Gerardo

2014-03-01

To study the dynamics of Breath Figure phenomenon, a control of both the rate of flow and temperature of water vapor is required. The experimental setup widely used is a non hermetically closed chamber with cylindrical geometry and axial inlets and outlets. In this work we present measurements in a cylindrical chamber with diameter 10 cm and 1.5 cm height, keeping a constant temperature (10 °C). We are focused in the velocity field when a gradient of the temperatures is produced between the base plate and the vapor. With a flux of water vapor of 250 mil/min at room temperature (21 °C), the Reynolds number measured in one inlet is 755. Otherwise, the temperatures of water vapor varies from 21 to 40 °C. The velocity profile is obtained by hot wire anemometry. We identify the stagnations and the possibly instabilities regions for an empty plate and with a well defined shape obstacle as a fashion sample. Facultad de Ciencias, UNAM.

On the Flame Height Definition for Upward Flame Spread

OpenAIRE

Consalvi, Jean L; Pizzo, Yannick; Porterie, Bernard; Torero, Jose L

2007-01-01

Flame height is defined by the experimentalists as the average position of the luminous flame and, consequently is not directly linked with a quantitative value of a physical parameter. To determine flame heights from both numerical and theoretical results, a more quantifiable criterion is needed to define flame heights and must be in agreement with the experiments to allow comparisons. For wall flames, steady wall flame experiments revealed that flame height may be define...

Uncertainty assessment of 3D instantaneous velocity model from stack velocities

Science.gov (United States)

Emanuele Maesano, Francesco; D'Ambrogi, Chiara

2015-04-01

3D modelling is a powerful tool that is experiencing increasing applications in data analysis and dissemination. At the same time the need of quantitative uncertainty evaluation is strongly requested in many aspects of the geological sciences and by the stakeholders. In many cases the starting point for 3D model building is the interpretation of seismic profiles that provide indirect information about the geology of the subsurface in the domain of time. The most problematic step in the 3D modelling construction is the conversion of the horizons and faults interpreted in time domain to the depth domain. In this step the dominant variable that could lead to significantly different results is the velocity. The knowledge of the subsurface velocities is related mainly to punctual data (sonic logs) that are often sparsely distributed in the areas covered by the seismic interpretation. The extrapolation of velocity information to wide extended horizons is thus a critical step to obtain a 3D model in depth that can be used for predictive purpose. In the EU-funded GeoMol Project, the availability of a dense network of seismic lines (confidentially provided by ENI S.p.A.) in the Central Po Plain, is paired with the presence of 136 well logs, but few of them have sonic logs and in some portion of the area the wells are very widely spaced. The depth conversion of the 3D model in time domain has been performed testing different strategies for the use and the interpolation of velocity data. The final model has been obtained using a 4 layer cake 3D instantaneous velocity model that considers both the initial velocity (v0) in every reference horizon and the gradient of velocity variation with depth (k). Using this method it is possible to consider the geological constraint given by the geometries of the horizons and the geo-statistical approach to the interpolation of velocities and gradient. Here we present an experiment based on the use of set of pseudo-wells obtained from the

Evidence of inbreeding depression on human height.

Directory of Open Access Journals (Sweden)

Ruth McQuillan

Full Text Available Stature is a classical and highly heritable complex trait, with 80%-90% of variation explained by genetic factors. In recent years, genome-wide association studies (GWAS have successfully identified many common additive variants influencing human height; however, little attention has been given to the potential role of recessive genetic effects. Here, we investigated genome-wide recessive effects by an analysis of inbreeding depression on adult height in over 35,000 people from 21 different population samples. We found a highly significant inverse association between height and genome-wide homozygosity, equivalent to a height reduction of up to 3 cm in the offspring of first cousins compared with the offspring of unrelated individuals, an effect which remained after controlling for the effects of socio-economic status, an important confounder (χ(2 = 83.89, df = 1; p = 5.2 × 10(-20. There was, however, a high degree of heterogeneity among populations: whereas the direction of the effect was consistent across most population samples, the effect size differed significantly among populations. It is likely that this reflects true biological heterogeneity: whether or not an effect can be observed will depend on both the variance in homozygosity in the population and the chance inheritance of individual recessive genotypes. These results predict that multiple, rare, recessive variants influence human height. Although this exploratory work focuses on height alone, the methodology developed is generally applicable to heritable quantitative traits (QT, paving the way for an investigation into inbreeding effects, and therefore genetic architecture, on a range of QT of biomedical importance.

Velocity Feedback Experiments

Directory of Open Access Journals (Sweden)

Chiu Choi

2017-02-01

Full Text Available Transient response such as ringing in a control system can be reduced or removed by velocity feedback. It is a useful control technique that should be covered in the relevant engineering laboratory courses. We developed velocity feedback experiments using two different low cost technologies, viz., operational amplifiers and microcontrollers. These experiments can be easily integrated into laboratory courses on feedback control systems or microcontroller applications. The intent of developing these experiments was to illustrate the ringing problem and to offer effective, low cost solutions for removing such problem. In this paper the pedagogical approach for these velocity feedback experiments was described. The advantages and disadvantages of the two different implementation of velocity feedback were discussed also.

[Influence of disc height on outcome of posterolateral fusion].

Science.gov (United States)

Drain, O; Lenoir, T; Dauzac, C; Rillardon, L; Guigui, P

2008-09-01

Experimentally, posterolateral fusion only provides incomplete control of flexion-extension, rotation and lateral inclination forces. The stability deficit increases with increasing height of the anterior intervertebral space, which for some warrants the adjunction of an intersomatic arthrodesis in addition to the posterolateral graft. Few studies have been devoted to the impact of disc height on the outcome of posterolateral fusion. The purpose of this work was to investigate the spinal segment immobilized by the posterolateral fusion: height of the anterior intervertebral space, the clinical and radiographic impact of changes in disc height, and the short- and long-term impact of disc height measured preoperatively on clinical and radiographic outcome. In order to obtain a homogeneous group of patients, the series was limited to patients undergoing posterolateral arthrodesis for degenerative spondylolisthesis, in combination with radicular release. This was a retrospective analysis of a consecutive series of 66 patients with mean 52 months follow-up (range 3-63 months). A dedicated self-administered questionnaire was used to collect data on pre- and postoperative function, the SF-36 quality of life score, and patient satisfaction. Pre- and postoperative (early, one year, last follow-up) radiographic data were recorded: olisthesic level, disc height, intervertebral angle, intervertebral mobility (angular, anteroposterior), and global measures of sagittal balance (thoracic kyphosis, lumbar lordosis, T9 sagittal tilt, pelvic version, pelvic incidence, sacral slope). SpineView was used for all measures. Univariate analysis searched for correlations between variation in disc height and early postoperative function and quality of fusion at last follow-up. Multivariate analysis was applied to the following preoperative parameters: intervertebral angle, disc height, intervertebral mobility, sagittal balance parameters, use of osteosynthesis or not. At the olisthesic

Comparison of mixing height parameterizations with profiles measurements

Energy Technology Data Exchange (ETDEWEB)

Jaquier, A.; Stuebi, R.; Tercier, P. [Swiss Meteorological Inst., SMI - MeteoSwiss, Payerne (Switzerland)

1997-10-01

Different meteorological pre-processors for dispersion studies are available to derive the atmospheric boundary layer mixing height (MH). The analysis of their performances has been reviewed in the framework of the European COST Action 710. In this project, the computed mixing height values have been compared with data derived mostly from aero-logical sounding analysis and Sodar measurements. Since then, a new analysis of a low-tropospheric wind profiler (WP) data has been performed taking advantage of its high data sampling ({delta}t {approx} 30 sec.). The comparison between these recent results and aero-logical sounding, Sodar data, as well as to meteorological pre-processors calculations are reported for three periods of several days corresponding to different meteorological situations. In convective conditions, the pre-processors give reasonable level, the mixing height growing rate is in fair agreement with the measured one. In stable cloudy daytime conditions, the modeled mixing height does not correspond to any measured height. (LN)

Planetary boundary layer height over the Indian subcontinent: Variability and controls with respect to monsoon

Science.gov (United States)

Sathyanadh, Anusha; Prabhakaran, Thara; Patil, Chetana; Karipot, Anandakumar

2017-10-01

Planetary boundary layer (PBL) height characteristics over the Indian sub-continent at diurnal to seasonal scales and its controlling factors in relation to monsoon are investigated. The reanalysis (Modern Era Retrospective analysis for Research and Applications, MERRA) PBL heights (PBLH) used for the study are validated against those derived from radiosonde observations and radio occultation air temperature and humidity profiles. The radiosonde observations include routine India Meteorological Department observations at two locations (coastal and an inland) for one full year and campaign based early afternoon radiosonde observations at six inland locations over the study region for selected days from May-September 2011. The temperature and humidity profiles from radio occultations spread over the sub-continent at irregular timings during the year 2011. The correlations and root mean square errors are in the range 0.74-0.83 and 407 m-643 m, respectively. Large pre-monsoon, monsoon and post-monsoon variations in PBL maximum height (1000 m-4000 m), time of occurrence of maximum height (11:00 LST-17:00 LST) and growth rate (100 to 400 m h- 1) are noted over the land, depending on geographical location and more significantly on the moisture availability which influences the surface sensible and latent heat fluxes. The PBLH variations associated with active-break intra-seasonal monsoon oscillations are up to 1000 m over central Indian locations. Inter relationship between the PBLH and the controlling factors, i.e. Evaporative Fraction, net radiation, friction velocity, surface Richardson number, and scalar diffusivity fraction, show significant variation between dry and wet PBL regimes, which also varies with geographical location. Evaporative fraction has dominant influence on the PBLH over the region. Enhanced entrainment during monsoon contributes to reduction in PBLH, whereas the opposite effect is noted during dry period. Linear regression, cross wavelet and

The velocity of sound

International Nuclear Information System (INIS)

Beyer, R.T.

1985-01-01

The paper reviews the work carried out on the velocity of sound in liquid alkali metals. The experimental methods to determine the velocity measurements are described. Tables are presented of reported data on the velocity of sound in lithium, sodium, potassium, rubidium and caesium. A formula is given for alkali metals, in which the sound velocity is a function of shear viscosity, atomic mass and atomic volume. (U.K.)

Measuring perceived ceiling height in a visual comparison task.

Science.gov (United States)

von Castell, Christoph; Hecht, Heiko; Oberfeld, Daniel

2017-03-01

When judging interior space, a dark ceiling is judged to be lower than a light ceiling. The method of metric judgments (e.g., on a centimetre scale) that has typically been used in such tasks may reflect a genuine perceptual effect or it may reflect a cognitively mediated impression. We employed a height-matching method in which perceived ceiling height had to be matched with an adjustable pillar, thus obtaining psychometric functions that allowed for an estimation of the point of subjective equality (PSE) and the difference limen (DL). The height-matching method developed in this paper allows for a direct visual match and does not require metric judgment. It has the added advantage of providing superior precision. Experiment 1 used ceiling heights between 2.90 m and 3.00 m. The PSE proved sensitive to slight changes in perceived ceiling height. The DL was about 3% of the physical ceiling height. Experiment 2 found similar results for lower (2.30 m to 2.50 m) and higher (3.30 m to 3.50 m) ceilings. In Experiment 3, we additionally varied ceiling lightness (light grey vs. dark grey). The height matches showed that the light ceiling appeared significantly higher than the darker ceiling. We therefore attribute the influence of ceiling lightness on perceived ceiling height to a direct perceptual rather than a cognitive effect.

Variability of the Mixed-Layer Height Over Mexico City

Science.gov (United States)

García-Franco, J. L.; Stremme, W.; Bezanilla, A.; Ruiz-Angulo, A.; Grutter, M.

2018-02-01

The diurnal and seasonal variability of the mixed-layer height in urban areas has implications for ground-level air pollution and the meteorological conditions. Measurements of the backscatter of light pulses with a commercial lidar system were performed for a continuous period of almost six years between 2011 and 2016 in the southern part of Mexico City. The profiles were temporally and vertically smoothed, clouds were filtered out, and the mixed-layer height was determined with an ad hoc treatment of both the filtered and unfiltered profiles. The results are in agreement when compared with values of mixed-layer height reconstructed from, (i) radiosonde data, and (ii) surface and vertical column densities of a trace gas. The daily maxima of the mean mixed-layer height reach values > 3 km above ground level in the months of March-April, and are clearly lower (pollution episodes and the height of the mixed layer. The growth rate of the convective mixed-layer height has a seasonal behaviour, which is characterized together with the mixed-layer-height anomalies. A clear residual layer is evident from the backscattered signals recorded in days with specific atmospheric conditions, but also from the cloud-filtered mean diurnal profiles. The occasional presence of a residual layer results in an overestimation of the reported mixed-layer height during the night and early morning hours.

Estimating Mixing Heights Using Microwave Temperature Profiler

Science.gov (United States)

Nielson-Gammon, John; Powell, Christina; Mahoney, Michael; Angevine, Wayne

2008-01-01

A paper describes the Microwave Temperature Profiler (MTP) for making measurements of the planetary boundary layer thermal structure data necessary for air quality forecasting as the Mixing Layer (ML) height determines the volume in which daytime pollution is primarily concentrated. This is the first time that an airborne temperature profiler has been used to measure the mixing layer height. Normally, this is done using a radar wind profiler, which is both noisy and large. The MTP was deployed during the Texas 2000 Air Quality Study (TexAQS-2000). An objective technique was developed and tested for estimating the ML height from the MTP vertical temperature profiles. In order to calibrate the technique and evaluate the usefulness of this approach, estimates from a variety of measurements during the TexAQS-2000 were compared. Estimates of ML height were used from radiosondes, radar wind profilers, an aerosol backscatter lidar, and in-situ aircraft measurements in addition to those from the MTP.

Weighting of field heights for sharpness and noisiness

Science.gov (United States)

Keelan, Brian W.; Jin, Elaine W.

2009-01-01

Weighting of field heights is important in cases when a single numerical value needs to be calculated that characterizes an attribute's overall impact on perceived image quality. In this paper we report an observer study to derive the weighting of field heights for sharpness and noisiness. One-hundred-forty images were selected to represent a typical consumer photo space distribution. Fifty-three sample points were sampled per image, representing field heights of 0, 14, 32, 42, 51, 58, 71, 76, 86% and 100%. Six observers participated in this study. The field weights derived in this report include both: the effect of area versus field height (which is a purely objective, geometric factor); and the effect of the spatial distribution of image content that draws attention to or masks each of these image structure attributes. The results show that relative to the geometrical area weights, sharpness weights were skewed to lower field heights, because sharpness-critical subject matter was often positioned relatively near the center of an image. Conversely, because noise can be masked by signal, noisiness-critical content (such as blue skies, skin tones, walls, etc.) tended to occur farther from the center of an image, causing the weights to be skewed to higher field heights.

Falls from height: A retrospective analysis.

Science.gov (United States)

Turgut, Kasim; Sarihan, Mehmet Ediz; Colak, Cemil; Güven, Taner; Gür, Ali; Gürbüz, Sükrü

2018-01-01

Emergency services manage trauma patients frequently and falls from height comprise the main cause of emergency service admissions. In this study, we aimed to analyse the demographic characteristics of falls from height and their relationship to the mortality. A total of 460 patients, who admitted to the Emergency Department of Inonu University between November 2011 and November 2014 with a history of fall from height, were examined retrospectively. Demographic parameters, fall characteristics and their effect to mortality were evaluated statistically. The study comprised of 292 (63.5%) men and 168 (36.5%) women patients. The mean age of all patients was 27±24.99 years. Twenty-six (5.6%) patients died and the majority of them were in ≥62 years old group. The highest percentage of falls was at 0-5 years age group (28.3%). People fell mainly from 1.1-4 metres(m) level (46.1%). The causes of falls were ordered as unintentional (92.2%), workplace (8.1%) and suicidal (1.7%). Skin and soft tissue injuries (37.4%) were the main traumatic lesions. Age, fall height, fall place, lineer skull fracture, subarachnoidal hemorrhage, cervical fracture, thoracic vertebra fracture and trauma scores had statistically significant effect on mortality. The casualties died because of subarachnoid hemorrhage mostly.

Development and Evaluation of Models for the Relationship between Tree Height and Diameter at Breast Height for Chinese-Fir Plantations in Subtropical China.

Science.gov (United States)

Li, Yan-qiong; Deng, Xiang-wen; Huang, Zhi-hong; Xiang, Wen-hua; Yan, Wen-de; Lei, Pi-feng; Zhou, Xiao-lu; Peng, Chang-hui

2015-01-01

Tree diameter at breast height (dbh) and height are the most important variables used in forest inventory and management as well as forest carbon-stock estimation. In order to identify the key stand variables that influence the tree height-dbh relationship and to develop and validate a suit of models for predicting tree height, data from 5961 tree samples aged from 6 years to 53 years and collected from 80 Chinese-fir plantation plots were used to fit 39 models, including 33 nonlinear models and 6 linear models, were developed and evaluated into two groups. The results showed that composite models performed better in height estimate than one-independent-variable models. Nonlinear composite Model 34 and linear composite Model 6 were recommended for predicting tree height in Chinese fir plantations with a dbh range between 4 cm and 40 cm when the dbh data for each tree and the quadratic mean dbh of the stand (Dq) and mean height of the stand (Hm) were available. Moreover, Hm could be estimated by using the formula Hm = 11.707 × l n(Dq)-18.032. Clearly, Dq was the primary stand variable that influenced the height-dbh relationship. The parameters of the models varied according to stand age and site. The inappropriate application of provincial or regional height-dbh models for predicting small tree height at local scale may result in larger uncertainties. The method and the recommended models developed in this study were statistically reliable for applications in growth and yield estimation for even-aged Chinese-fir plantation in Huitong and Changsha. The models could be extended to other regions and to other tree species only after verification in subtropical China.

The height of watermelons with wall

International Nuclear Information System (INIS)

Feierl, Thomas

2012-01-01

We derive asymptotics for the moments as well as the weak limit of the height distribution of watermelons with p branches with wall. This generalizes a famous result of de Bruijn et al (1972 Graph Theory and Computing (New York: Academic) pp 15–22) on the average height of planted plane trees, and results by Fulmek (2007 Electron. J. Combin. 14 R64) and Katori et al (2008 J. Stat. Phys. 131 1067–83) on the expected value and higher moments, respectively, of the height distribution of watermelons with two branches. The asymptotics for the moments depend on the analytic behaviour of certain multidimensional Dirichlet series. In order to obtain this information, we prove a reciprocity relation satisfied by the derivatives of one of Jacobi’s theta functions, which generalizes the well-known reciprocity law for Jacobi’s theta functions. (paper)

Physical growth of the shuar: Height, Weight, and BMI references for an indigenous amazonian population.

Science.gov (United States)

Urlacher, Samuel S; Blackwell, Aaron D; Liebert, Melissa A; Madimenos, Felicia C; Cepon-Robins, Tara J; Gildner, Theresa E; Snodgrass, J Josh; Sugiyama, Lawrence S

2016-01-01

Information concerning physical growth among small-scale populations remains limited, yet such data are critical to local health efforts and to foster basic understandings of human life history and variation in childhood development. Using a large dataset and robust modeling methods, this study aims to describe growth from birth to adulthood among the indigenous Shuar of Amazonian Ecuador. Mixed-longitudinal measures of height, weight, and body mass index (BMI) were collected from Shuar participants (n = 2,463; age: 0-29 years). Centile growth curves and tables were created for each anthropometric variable of interest using Generalized Additive Models for Location, Scale, and Shape (GAMLSS). Pseudo-velocity and Lambda-Mu-Sigma curves were generated to further investigate Shuar patterns of growth and to facilitate comparison with United States Center for Disease Control and Prevention and multinational World Health Organization growth references. The Shuar are small throughout life and exhibit complex patterns of growth that differ substantially from those of international references. Similar to other Amazonians, Shuar growth in weight compares more favorably to references than growth in height, resulting in BMI curves that approximate international medians. Several additional characteristics of Shuar development are noteworthy, including large observed variation in body size early in life, significant infant growth faltering, extended male growth into adulthood, and a markedly early female pubertal growth spurt in height. Phenotypic plasticity and genetic selection in response to local environmental factors may explain many of these patterns. Providing a detailed reference of growth for the Shuar and other Amazonian populations, this study possesses direct clinical application and affords valuable insight into childhood health and the ecology of human growth. © 2015 Wiley Periodicals, Inc.

Predicting human height by Victorian and genomic methods.

Science.gov (United States)

Aulchenko, Yurii S; Struchalin, Maksim V; Belonogova, Nadezhda M; Axenovich, Tatiana I; Weedon, Michael N; Hofman, Albert; Uitterlinden, Andre G; Kayser, Manfred; Oostra, Ben A; van Duijn, Cornelia M; Janssens, A Cecile J W; Borodin, Pavel M

2009-08-01

In the Victorian era, Sir Francis Galton showed that 'when dealing with the transmission of stature from parents to children, the average height of the two parents, ... is all we need care to know about them' (1886). One hundred and twenty-two years after Galton's work was published, 54 loci showing strong statistical evidence for association to human height were described, providing us with potential genomic means of human height prediction. In a population-based study of 5748 people, we find that a 54-loci genomic profile explained 4-6% of the sex- and age-adjusted height variance, and had limited ability to discriminate tall/short people, as characterized by the area under the receiver-operating characteristic curve (AUC). In a family-based study of 550 people, with both parents having height measurements, we find that the Galtonian mid-parental prediction method explained 40% of the sex- and age-adjusted height variance, and showed high discriminative accuracy. We have also explored how much variance a genomic profile should explain to reach certain AUC values. For highly heritable traits such as height, we conclude that in applications in which parental phenotypic information is available (eg, medicine), the Victorian Galton's method will long stay unsurpassed, in terms of both discriminative accuracy and costs. For less heritable traits, and in situations in which parental information is not available (eg, forensics), genomic methods may provide an alternative, given that the variants determining an essential proportion of the trait's variation can be identified.

Water polo throwing velocity and kinematics: differences between competitive levels in male players.

Science.gov (United States)

Melchiorri, G; Viero, V; Triossi, T; De Sanctis, D; Padua, E; Salvati, A; Galvani, C; Bonifazi, M; Del Bianco, R; Tancredi, V

2015-11-01

In water polo, throwing is one of the most important and frequently used technical skills for the player. There is no scientific literature that provides information about differences in throwing between elite and sub-elite water polo players. The aim of our study was to study differences in throwing velocities and kinematic variables in elite and sub-elite level male water polo players. We considered the variables under standardized conditions during a typical motion, the five-meter shot (penalty). Thirty-four athletes from the Men's First Division Water Polo Championship and forty-two players participating in the National Fourth Division League, took part in the study. Video analysis measures were taken with high-speed digital cameras and the videos were analyzed offline with Dartfish 5.0 Pro. No correlation was found between body mass, height and throwing velocity. Elite players had higher values ​for ball speed (22.8±2.4 m/s for elite team and 18.4±1.7 m/s for sub-elite team; P=0.002) and greater elbow angle (157.5±10.3 degree for elite team versus 146.7±8.9 degree for sub-elite team; P=0.002). In elite team the throwing time was lower (165.6±22.2 and 188.6±23.9 ms, respectively; P=0.05) and the shoulder angle was smaller (115.1±10.3 and 123.8±12.4 degree, respectively; P=0.03) than in sub-elite team. Head height was significantly greater in elite players (elite players 71.1±8.7 cm, sub-elite players 65.6±6.2 cm; P=0.03). Differences in kinematic characteristics between elite and sub-elite players were showed. Differences in elbow and shoulder action must be considered both in training and injury prevention.

Nerve conduction velocity

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/003927.htm Nerve conduction velocity To use the sharing features on this page, please enable JavaScript. Nerve conduction velocity (NCV) is a test to see ...

ANALYSIS AND CORRECTION OF SYSTEMATIC HEIGHT MODEL ERRORS

Directory of Open Access Journals (Sweden)

K. Jacobsen

2016-06-01

Full Text Available The geometry of digital height models (DHM determined with optical satellite stereo combinations depends upon the image orientation, influenced by the satellite camera, the system calibration and attitude registration. As standard these days the image orientation is available in form of rational polynomial coefficients (RPC. Usually a bias correction of the RPC based on ground control points is required. In most cases the bias correction requires affine transformation, sometimes only shifts, in image or object space. For some satellites and some cases, as caused by small base length, such an image orientation does not lead to the possible accuracy of height models. As reported e.g. by Yong-hua et al. 2015 and Zhang et al. 2015, especially the Chinese stereo satellite ZiYuan-3 (ZY-3 has a limited calibration accuracy and just an attitude recording of 4 Hz which may not be satisfying. Zhang et al. 2015 tried to improve the attitude based on the color sensor bands of ZY-3, but the color images are not always available as also detailed satellite orientation information. There is a tendency of systematic deformation at a Pléiades tri-stereo combination with small base length. The small base length enlarges small systematic errors to object space. But also in some other satellite stereo combinations systematic height model errors have been detected. The largest influence is the not satisfying leveling of height models, but also low frequency height deformations can be seen. A tilt of the DHM by theory can be eliminated by ground control points (GCP, but often the GCP accuracy and distribution is not optimal, not allowing a correct leveling of the height model. In addition a model deformation at GCP locations may lead to not optimal DHM leveling. Supported by reference height models better accuracy has been reached. As reference height model the Shuttle Radar Topography Mission (SRTM digital surface model (DSM or the new AW3D30 DSM, based on ALOS

Influence of wind velocity fluctuation on air temperature difference between the fan and ground levels and the effect of frost protective fan operation

International Nuclear Information System (INIS)

Araki, T.; Matsuo, K.; Miyama, D.; Sumikawa, O.; Araki, S.

2008-01-01

We invested the influence of wind velocity fluctuation on air temperature difference between the fan (4.8 m) and ground levels (0.5 m) and the effect of frost protective fan operation in order to develop a new method to reduce electricity consumption due to frost protective fan operation. The results of the investigations are summarized as follows: (1) Air temperature difference between the fan (4.8 m) and ground levels (0.5 m) was decreased following an increase in wind velocity, and the difference was less than 1°C for a wind velocity more than 3.0 m/s at a height of 6.5 m. (2) When the wind velocity was more than 2-3 m/s, there was hardly any increase in the temperature of the leaves. In contrast, when the wind velocity was less than 2-3 m/s, an increase in the temperature of the leaves was observed. Based on these results, it is possible that when the wind velocity is greater than 2-3 m, it prevents thermal inversion. Therefore, there would be no warmer air for the frost protective fan to return to the tea plants and the air turbulence produced by the frost protective fan would not reach the plants under the windy condition

Anterior Face Height Values in a Nigerian Population | Folaranmi ...

African Journals Online (AJOL)

... Anterior Upper Face Height 47.7 (4) mm, Anterior Total Face Height (ATFH) 108.5 (5) mm, ratio of ALFH to ATFH ALFH: ATFH 56 (4)%. Conclusion: This study provides anterior face height measurements, which will be of great significance in evaluating facial proportions andesthetics in orthodontics, orthognathic surgery, ...

Dominant height-based height-diameter equations for trees in southern Indiana

Science.gov (United States)

John A., Jr. Kershaw; Robert C. Morrissey; Douglass F. Jacobs; John R. Seifert; James B. McCarter

2008-01-01

Height-diameter equations are developed based on dominant tree data collected in 1986 in 8- to 17-year-old clearcuts and the phase 2 Forest Inventory and Analysis plots on the Hoosier National Forest in south central Indiana. Two equation forms are explored: the basic, three-parameter Chapman-Richards function, and a modification of the three-parameter equation...

Do centimetres matter? Self-reported versus estimated height measurements in parents.

Science.gov (United States)

Gozzi, T; Flück, Ce; L'allemand, D; Dattani, M T; Hindmarsh, P C; Mullis, P E

2010-04-01

An impressive discrepancy between reported and measured parental height is often observed. The aims of this study were: (a) to assess whether there is a significant difference between the reported and measured parental height; (b) to focus on the reported and, thereafter, measured height of the partner; (c) to analyse its impact on the calculated target height range. A total of 1542 individual parents were enrolled. The parents were subdivided into three groups: normal height (3-97th Centile), short (97%) stature. Overall, compared with men, women were far better in estimating their own height (p Women of normal stature underestimated the short partner and overestimated the tall partner, whereas male partners of normal stature overestimated both their short as well as tall partners. Women of tall stature estimated the heights of their short partners correctly, whereas heights of normal statured men were underestimated. On the other hand, tall men overestimated the heights of their female partners who are of normal and short stature. Furthermore, women of short stature estimated the partners of normal stature adequately, and the heights of their tall partners were overestimated. Interestingly, the short men significantly underestimated the normal, but overestimated tall female partners. Only measured heights should be used to perform accurate evaluations of height, particularly when diagnostic tests or treatment interventions are contemplated. For clinical trails, we suggest that only quality measured parental heights are acceptable, as the errors incurred in estimates may enhance/conceal true treatment effects.

The determination of the mixing height. Current progress and problems

Energy Technology Data Exchange (ETDEWEB)

Gryning, S.E.; Beyrich, F.; Batchvarova, E. [eds.

1997-10-01

This report contains extended abstracts of presentations given at a EURASAP Workshop on The Determination of the Mixing Height - Current Progress and Problems. The Workshop, initiated from discussions with Peter Builtjes, was held at Risoe National Laboratory 1-3 October 1997 within the framework of EURASAP (European Association for the Sciences of Air Pollution). The specific topics and chairpersons of the Workshop were: Theoretical Considerations (Sven-Erik Gryning), Mixing Height Estimation from Turbulence Measurements and In-Situ Soundings (Douw Steyn), Mixing Height Determination from NWP-Models (Han van Dop), Climatology and Global Aspects (Werner Klug), Mixing Height Determination from Remote Systems (Werner Klug), Verification of Mixing Height Parameterizations and Models (Frank Beyrich), Mixing Height over Complex Terrain (Ekaterina Batchvarova), Internal Boundary Layers: Mixing Height in Coastal Areas and Over Cities (Allen White). The discussion at the end of the Workshop was chaired by Robert Bornstein. (au)

Determination of velocity correction factors for real-time air velocity monitoring in underground mines

OpenAIRE

Zhou, Lihong; Yuan, Liming; Thomas, Rick; Iannacchione, Anthony

2017-01-01

When there are installations of air velocity sensors in the mining industry for real-time airflow monitoring, a problem exists with how the monitored air velocity at a fixed location corresponds to the average air velocity, which is used to determine the volume flow rate of air in an entry with the cross-sectional area. Correction factors have been practically employed to convert a measured centerline air velocity to the average air velocity. However, studies on the recommended correction fac...

Practical application of the geometric geoid for heighting over ...

African Journals Online (AJOL)

This is because a geoid model is required to convert ellipsoidal heights to orthometric heights that are used in practice. A local geometric geoid ... The geoid height is expressed as a function of the local plane coordinates through a biquadratic surface polynomial, using 14 GPS/levelling points. Five points have been used ...

Adult height, dietary patterns, and healthy aging.

Science.gov (United States)

Ma, Wenjie; Hagan, Kaitlin A; Heianza, Yoriko; Sun, Qi; Rimm, Eric B; Qi, Lu

2017-08-01

Background: Adult height has shown directionally diverse associations with several age-related disorders, including cardiovascular disease, cancer, decline in cognitive function, and mortality. Objective: We investigated the associations of adult height with healthy aging measured by a full spectrum of health outcomes, including incidence of chronic diseases, memory, physical functioning, and mental health, among populations who have survived to older age, and whether lifestyle factors modified such relations. Design: We included 52,135 women (mean age: 44.2 y) from the Nurses' Health Study without chronic diseases in 1980 and whose health status was available in 2012. Healthy aging was defined as being free of 11 major chronic diseases and having no reported impairment of subjective memory, physical impairment, or mental health limitations. Results: Of all eligible study participants, 6877 (13.2%) were classified as healthy agers. After adjustment for demographic and lifestyle factors, we observed an 8% (95% CI: 6%, 11%) decrease in the odds of healthy aging per SD (0.062 m) increase in height. Compared with the lowest category of height (≤1.57 m), the OR of achieving healthy aging in the highest category (≥1.70 m) was 0.80 (95% CI: 0.73, 0.87; P -trend healthy aging ( P -interaction = 0.005), and among the individual dietary factors characterizing the prudent dietary pattern, fruit and vegetable intake showed the strongest effect modification ( P -interaction = 0.01). The association of greater height with reduced odds of healthy aging appeared to be more evident among women with higher adherence to the prudent dietary pattern rich in vegetable and fruit intake. Conclusions: Greater height was associated with a modest decrease in the likelihood of healthy aging. A prudent diet rich in fruit and vegetables might modify the relation. © 2017 American Society for Nutrition.

Relationships between diameter and height of trees in natural ...

African Journals Online (AJOL)

Relationships between diameter and height of trees in natural tropical forest in Tanzania. Wilson A Mugasha, Ole M Bollandsås, Tron Eid. Abstract. The relationship between tree height (h) and tree diameter at breast height (dbh) is an important element describing forest stands. In addition, h often is a required variable in ...

Gradient-Based Optimization of Wind Farms with Different Turbine Heights

Energy Technology Data Exchange (ETDEWEB)

Stanley, Andrew P. J.; Thomas, Jared; Ning, Andrew; Annoni, Jennifer; Dykes, Katherine; Fleming, Paul

2017-01-09

Turbine wakes reduce power production in a wind farm. Current wind farms are generally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine hub heights. Results indicate that when a farm is optimized for layout and height with two separate height groups, COE can be lowered by as much as 5%-9%, compared to a similar layout and height optimization where all the towers are the same. The COE has the best improvement in farms with high turbine density and a low wind shear exponent.

Maternal and Paternal Height and the Risk of Preeclampsia.

Science.gov (United States)

Lee, Yunsung; Magnus, Per

2018-04-01

The etiology of preeclampsia is unknown. Tall women have been found to have lower incidence of preeclampsia. This points to a possible biological causal effect but may be because of socioeconomic confounding. We used paternal height as an unexposed control to examine confounding. The MoBa (Norwegian Mother and Child Cohort Study) was used to extract data on parental heights, maternal prepregnancy weight, other background factors, and pregnancy outcomes for 99 968 singleton births. Multiple logistic regression was used to estimate odds ratios for preeclampsia according to parental height. The adjusted odds ratio for preeclampsia was 0.74 (95% CI, 0.66-0.82) for women >172 cm as compared with women 186 cm was 1.03 (95% CI, 0.93-1.15) compared with men <178 cm. The association between maternal height and preeclampsia is unlikely to be because of confounding by familial, socioeconomic factors or by fetal genes related to height. The observed association between maternal height and preeclampsia merits further investigation. © 2018 American Heart Association, Inc.

Calculations of shape and stability of menisci in Czochralski growth with tables to determine meniscus heights, maximum heights and capillary constants

International Nuclear Information System (INIS)

Uelhoff, W.; Mika, K.

1975-05-01

The shape and stability of menisci occurring during Czochralski growth have been studied by means of numerical methods for the case of the free surface. The existence of minimal joining angles is shown, beyond which the growing crystal will separate from the melt. The dependence of the interface height on the joining angle for different crystal diameters was calculated. The maximum stable heights and the corresponding joining angles were determined as a function of crystal diameter. A method for measuring the capillary constant of the melt during Czochralski growth is proposed. The results are compared with known analytical approximations. Limitations of the applications caused by a finite crucible radius or low g values are pointed out. For practical use the following functions have been tabulated: 1) meniscus height in dependence on joining angle and crystal radius, 2) the radius-height-ratio in dependence on radius and angle for the calculation of the capillary constant, 3) the maximum stable height and the corresponding growth angle as a function of crystal radius. (orig.) [de

Height among Women is Curvilinearly Related to Life History Strategy

Directory of Open Access Journals (Sweden)

Abraham P. Buunk

2009-10-01

Full Text Available It was hypothesized that women of medium height would show a more secure, long-term mating pattern characterized by less jealousy, less intrasexual competition and a “slower” life history strategy. In three samples of female undergraduate students clear support was found for these hypotheses. In Study 1, among 120 participants, height was curvilinearly related to well-established measures of possessive and reactive jealousy, with women of medium height being less jealous than tall as well as short women. In Study 2, among 40 participants, height was curvilinearly related to intrasexual competition, with women of medium height being less competitive towards other women than tall as well as short women. In Study 3, among 299 participants, height was curvilinearly related to the Mini-K, a well-validated measure of “slower” life history strategy, with women of medium height having a slower life history strategy than tall as well as short women. The results suggest that women of medium height tend to follow a different mating strategy than either tall or short women. Various explanations and implications of these results are discussed.

Collective cell migration without proliferation: density determines cell velocity and wave velocity

Science.gov (United States)

Tlili, Sham; Gauquelin, Estelle; Li, Brigitte; Cardoso, Olivier; Ladoux, Benoît; Delanoë-Ayari, Hélène; Graner, François

2018-05-01

Collective cell migration contributes to embryogenesis, wound healing and tumour metastasis. Cell monolayer migration experiments help in understanding what determines the movement of cells far from the leading edge. Inhibiting cell proliferation limits cell density increase and prevents jamming; we observe long-duration migration and quantify space-time characteristics of the velocity profile over large length scales and time scales. Velocity waves propagate backwards and their frequency depends only on cell density at the moving front. Both cell average velocity and wave velocity increase linearly with the cell effective radius regardless of the distance to the front. Inhibiting lamellipodia decreases cell velocity while waves either disappear or have a lower frequency. Our model combines conservation laws, monolayer mechanical properties and a phenomenological coupling between strain and polarity: advancing cells pull on their followers, which then become polarized. With reasonable values of parameters, this model agrees with several of our experimental observations. Together, our experiments and model disantangle the respective contributions of active velocity and of proliferation in monolayer migration, explain how cells maintain their polarity far from the moving front, and highlight the importance of strain-polarity coupling and density in long-range information propagation.

Sensitivity of the urban airshed model to mixing height profiles

Energy Technology Data Exchange (ETDEWEB)

Rao, S.T.; Sistla, G.; Ku, J.Y.; Zhou, N.; Hao, W. [New York State Dept. of Environmental Conservation, Albany, NY (United States)

1994-12-31

The United States Environmental Protection Agency (USEPA) has recommended the use of the Urban Airshed Model (UAM), a grid-based photochemical model, for regulatory applications. One of the important parameters in applications of the UAM is the height of the mixed layer or the diffusion break. In this study, we examine the sensitivity of the UAM-predicted ozone concentrations to (a) a spatially invariant diurnal mixing height profile, and (b) a spatially varying diurnal mixing height profile for a high ozone episode of July 1988 for the New York Airshed. The 1985/88 emissions inventory used in the EPA`s Regional Oxidant Modeling simulations has been regridded for this study. Preliminary results suggest that the spatially varying case yields a higher peak ozone concentrations compared to the spatially invariant mixing height simulation, with differences in the peak ozone ranging from a few ppb to about 40 ppb for the days simulated. These differences are attributed to the differences in the shape of the mixing height profiles and its rate of growth during the morning hours when peak emissions are injected into the atmosphere. Examination of the impact of emissions reductions associated with these two mixing height profiles indicates that NO{sub x}-focussed controls provide a greater change in the predicted ozone peak under spatially invariant mixing heights than under the spatially varying mixing height profile. On the other hand, VOC-focussed controls provide a greater change in the predicted peak ozone levels under spatially varying mixing heights than under the spatially invariant mixing height profile.

17 Years of Cloud Heights from Terra, and Beyond

Science.gov (United States)

Davies, R.

2017-12-01

The effective cloud height, H, is the integral of observed cloud-top heights, weighted by their frequency of occurrence. Here we look at changes in the effective cloud height, H', as measured by the Multiangle Imaging Spectroradiometer (MISR) on the first Earth Observing System platform, Terra. Terra was launched in December 1999, and now has over 17 years of consistently measured climate records. Globally, HG' has an important influence on Earth's climate, whereas regionally, HR' is a useful measure of low frequency changes in circulation patterns. MISR has a sampling error in the annual mean HG' of ≈11 m, allowing fairly small interannual variations to be detected. This paper extends the previous 15-year summary that showed significant differences in the long term mean hemispheric cloud height changes. Also of interest are the correlations in tropical cloud height changes and related teleconnections. The largest ephemeral values in the annual HR' [over 1.5 km] are noted over the Central Pacific and the Maritime Continent. These changes are strongly anticorrelated with each other, being directly related to changes in ENSO. They are also correlated with the largest ephemeral changes in HG'. Around the equator, we find at least four distinct centres of similar fluctuations in cloud height. This paper examines the relative time dependence of these regional height changes, separately for La Niña and El Niño events, and stresses the value of extending the time series of uniformly measured cloud heights from space beyond EOS-Terra.

Phase Velocity Estimation of a Microstrip Line in a Stoichiometric Periodically Domain-Inverted LiTaO3 Modulator Using Electro-Optic Sampling Technique

Directory of Open Access Journals (Sweden)

Shintaro Hisatake

2008-01-01

Full Text Available We estimate the phase velocity of a modulation microwave in a quasi-velocity-matched (QVM electro-optic (EO phase modulator (QVM-EOM using EO sampling which is accurate and the most reliable technique for measuring voltage waveforms at an electrode. The substrate of the measured QVM-EOM is a stoichiometric periodically domain-inverted LiTaO3 crystal. The electric field of a standing wave in a resonant microstrip line (width: 0.5 mm, height: 0.5 mm is measured by employing a CdTe crystal as an EO sensor. The wavelength of the traveling microwave at 16.0801 GHz is determined as 3.33 mm by fitting the theoretical curve to the measured electric field distribution. The phase velocity is estimated as vm=5.35×107 m/s, though there exists about 5% systematic error due to the perturbation by the EO sensor. Relative dielectric constant of εr=41.5 is led as the maximum likelihood value that derives the estimated phase velocity.

Simulation of ICESat-2 canopy height retrievals for different ecosystems

Science.gov (United States)

Neuenschwander, A. L.

2016-12-01

Slated for launch in late 2017 (or early 2018), the ICESat-2 satellite will provide a global distribution of geodetic measurements from a space-based laser altimeter of both the terrain surface and relative canopy heights which will provide a significant benefit to society through a variety of applications ranging from improved global digital terrain models to producing distribution of above ground vegetation structure. The ATLAS instrument designed for ICESat-2, will utilize a different technology than what is found on most laser mapping systems. The photon counting technology of the ATLAS instrument onboard ICESat-2 will record the arrival time associated with a single photon detection. That detection can occur anywhere within the vertical distribution of the reflected signal, that is, anywhere within the vertical distribution of the canopy. This uncertainty of where the photon will be returned from within the vegetation layer is referred to as the vertical sampling error. Preliminary simulation studies to estimate vertical sampling error have been conducted for several ecosystems including woodland savanna, montane conifers, temperate hardwoods, tropical forest, and boreal forest. The results from these simulations indicate that the canopy heights reported on the ATL08 data product will underestimate the top canopy height in the range of 1 - 4 m. Although simulation results indicate the ICESat-2 will underestimate top canopy height, there is, however, a strong correlation between ICESat-2 heights and relative canopy height metrics (e.g. RH75, RH90). In tropical forest, simulation results indicate the ICESat-2 height correlates strongly with RH90. Similarly, in temperate broadleaf forest, the simulated ICESat-2 heights were also strongly correlated with RH90. In boreal forest, the simulated ICESat-2 heights are strongly correlated with RH75 heights. It is hypothesized that the correlations between simulated ICESat-2 heights and canopy height metrics are a

Pubertal Development and Prepubertal Height and Weight Jointly Predict Young Adult Height and Body Mass Index in a Prospective Study in South Africa.

Science.gov (United States)

Stein, Aryeh D; Lundeen, Elizabeth A; Martorell, Reynaldo; Suchdev, Parminder S; Mehta, Neil K; Richter, Linda M; Norris, Shane A

2016-07-01

Height and adiposity track over childhood, but few studies, to our knowledge, have longitudinally examined the mediating relation of the timing and progression of puberty. We assessed interrelations between prepubertal height and body mass index, the progression through puberty, and young adult height and adiposity. We analyzed data from the Birth to Twenty Plus study (females, n = 823; males, n = 765). Serial measures of anthropometry and pubertal development were obtained between ages 9 and 16 y. We used latent class growth analysis to categorize pubertal development with respect to pubic hair (females and males), breasts (females), and genitalia (males) development. Adult height and weight were obtained at ages 18 to 20 y. Among females, higher latent class (earlier initiation and faster progression through puberty) was associated with an increased risk of obesity [pubic hair class 3 compared with class 1: RR, 3.41 (95% CI: 1.57, 7.44)] and inconsistent associations with height. Among males, higher latent class was associated with increased adult height [pubic hair development class 3 compared with class 1: 2.43 cm (95% CI: 0.88, 4.00)] and increased risk of overweight/obesity [pubic hair development class 3 compared with class 1: OR, 3.44 (95% CI: 1.44, 8.20)]. In females, the association with adult height became inverse after adjusting for prepubertal height [pubic hair development class 3 compared with class 1: females, -1.31 cm (95% CI: -2.32, -0.31)]; in males, the association with height was attenuated with this adjustment [-0.56 cm (95% CI: -1.63, 0.52)]. Associations with adiposity were attenuated after adjusting for prepubertal adiposity. Progression through puberty modifies the relation between prepubertal and adult anthropometry. Screening for early or rapid progression of puberty might identify children at an increased risk of becoming overweight or obese adults.

Consideration of some difficulties in migration velocity analysis; Migration velocity analysis no shomondai ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Akama, K [Japan National Oil Corp., Tokyo (Japan). Technology Research Center; Matsuoka, T [Japan Petroleum Exploration Corp., Tokyo (Japan)

1997-10-22

Concerning migration velocity analysis in the seismic exploration method, two typical techniques, out of velocity analysis techniques using residual moveout in the CIP gather, are verified. Deregowski`s method uses pre-stacking deep-level migration records for velocity analysis to obtain velocities free of spatial inconsistency and not dependent on the velocity structure. This method is very like the conventional DMO velocity analysis method and is easy to understand intuitively. In this method, however, error is apt to be aggravated in the process of obtaining the depth-sector velocity from the time-RMS velocity. Al-Yahya`s method formulates the moveout residual in the CIP gather. This assumes horizontal stratification and a small residual velocity, however, and fails to guarantee convergence in the case of a steep structure or a grave model error. In the updating of the velocity model, in addition, it has to maintain required accuracy and, at the same time, incorporate smoothing to ensure not to deteriorate high convergence. 2 refs., 5 figs.

Contamination control in HVAC systems for aseptic processing area. Part I: Case study of the airflow velocity in a unidirectional airflow workstation with computational fluid dynamics.

Science.gov (United States)

Ogawa, M

2000-01-01

A unidirectional airflow workstation for processing a sterile pharmaceutical product is required to be "Grade A," according to EU-GMP and WHO-GMP. These regulations have employed the wording of "laminar airflow" for unidirectional airflow, with an unclear definition given. This seems to have allowed many reports to describe discussion of airflow velocity only. The guidance values as to the velocity are expressed in various words of 90 ft/min, 0.45 m/sec, 0.3 m/sec, +/- 20%, or "homogeneous air speed." It has been also little clarified how variation in airflow velocity gives influences on contamination control of a workstation working with varying key characteristics, such as ceiling height, internal heat load, internal particle generation, etc. The present author has revealed following points from a case study using Computational Fluid Dynamics: the airflow characteristic in Grade A area shows no significant changes with varying the velocity of supplied airflow, and the particles generated from the operator will be exhausted outside Grade A area without contamination.

Horizontal and Vertical Velocities Derived from the IDS Contribution to ITRF2014, and Comparisons with Geophysical Models

Science.gov (United States)

Moreaux, G.; Lemoine, F. G.; Argus, D. F.; Santamaria-Gomez, A.; Willis, P.; Soudarin, L.; Gravelle, M.; Ferrage, P.

2016-01-01

In the context of the 2014 realization of the International Terrestrial Reference Frame (ITRF2014), the International DORIS Service (IDS) has delivered to the IERS a set of 1140 weekly SINEX files including station coordinates and Earth orientation parameters, covering the time period from 1993.0 to 2015.0. From this set of weekly SINEX files, the IDS Combination Center estimated a cumulative DORIS position and velocity solution to obtain mean horizontal and vertical motion of 160 stations at 71 DORIS sites. The main objective of this study is to validate the velocities of the DORIS sites by comparison with external models or time series. Horizontal velocities are compared with two recent global plate models (GEODVEL 2010 and NNR-MORVEL56). Prior to the comparisons, DORIS horizontal velocities were corrected for Global Isostatic Adjustment (GIA) from the ICE-6G (VM5a) model. For more than half of the sites, the DORIS horizontal velocities differ from the global plate models by less than 2-3 mm/yr. For five of the sites (Arequipa, Dionysos/Gavdos, Manila, Santiago) with horizontal velocity differences wrt these models larger than 10 mm/yr, comparisons with GNSS estimates show the veracity of the DORIS motions. Vertical motions from the DORIS cumulative solution are compared with the vertical velocities derived from the latest GPS cumulative solution over the time span 1995.0-2014.0 from the University of La Rochelle (ULR6) solution at 31 co-located DORIS-GPS sites. These two sets of vertical velocities show a correlation coefficient of 0.83. Vertical differences are larger than 2 mm/yr at 23 percent of the sites. At Thule the disagreement is explained by fine-tuned DORIS discontinuities in line with the mass variations of outlet glaciers. Furthermore, the time evolution of the vertical time series from the DORIS station in Thule show similar trends to the GRACE equivalent water height.

Horizontal and vertical velocities derived from the IDS contribution to ITRF2014, and comparisons with geophysical models

Science.gov (United States)

Moreaux, G.; Lemoine, F. G.; Argus, D. F.; Santamaría-Gómez, A.; Willis, P.; Soudarin, L.; Gravelle, M.; Ferrage, P.

2016-10-01

In the context of the 2014 realization of the International Terrestrial Reference Frame, the International DORIS (Doppler Orbitography Radiopositioning Integrated by Satellite) Service (IDS) has delivered to the IERS a set of 1140 weekly SINEX files including station coordinates and Earth orientation parameters, covering the time period from 1993.0 to 2015.0. From this set of weekly SINEX files, the IDS combination centre estimated a cumulative DORIS position and velocity solution to obtain mean horizontal and vertical motion of 160 stations at 71 DORIS sites. The main objective of this study is to validate the velocities of the DORIS sites by comparison with external models or time-series. Horizontal velocities are compared with two recent global plate models (GEODVEL 2010 and NNR-MORVEL56). Prior to the comparisons, DORIS horizontal velocities were corrected for Global Isostatic Adjustment from the ICE-6G (VM5a) model. For more than half of the sites, the DORIS horizontal velocities differ from the global plate models by less than 2-3 mm yr-1. For five of the sites (Arequipa, Dionysos/Gavdos, Manila and Santiago) with horizontal velocity differences with respect to these models larger than 10 mm yr-1, comparisons with GNSS estimates show the veracity of the DORIS motions. Vertical motions from the DORIS cumulative solution are compared with the vertical velocities derived from the latest GPS cumulative solution over the time span 1995.0-2014.0 from the University of La Rochelle solution at 31 co-located DORIS-GPS sites. These two sets of vertical velocities show a correlation coefficient of 0.83. Vertical differences are larger than 2 mm yr-1 at 23 percent of the sites. At Thule, the disagreement is explained by fine-tuned DORIS discontinuities in line with the mass variations of outlet glaciers. Furthermore, the time evolution of the vertical time-series from the DORIS station in Thule show similar trends to the GRACE equivalent water height.

Factors influencing the height of Hawaiian lava fountains: implications for the use of fountain height as an indicator of magma gas content

Science.gov (United States)

Parfitt, E.A.; Wilson, L.; Neal, C.A.

1995-01-01

The heights of lava fountains formed in Hawaiian-style eruptions are controlled by magma gas content, volume flux and the amounts of lava re-entrainment and gas bubble coalescence. Theoretical models of lava fountaining are used to analyse data on lava fountain height variations collected during the 1983-1986 Pu'u 'O'o vent of Kilauea volcano, Hawaii. The results show that the variable fountain heights can be largely explained by the impact of variations in volume flux and amount of lava re-entrainment on erupting magmas with a constant gas content of ???0.32 wt.% H2O. However, the gas content of the magma apparently declined by ???0.05 wt.% during the last 10 episodes of the eruption series and this decline is attributed to more extensive pre-eruption degassing due to a shallowing of the sub-vent feeder dike. It is concluded that variations in lava fountain height cannot be simply interpreted as variations in gas content, as has previously been suggested, but that fountain height can still be a useful guide to minimum gas contents. Where sufficient data are available on eruptive volume fluxes and extent of lava entrainment, greatly improved estimates can be made of magma gas content from lava fountain height. ?? 1995 Springer-Verlag.

Brain structure mediates the association between height and cognitive ability.

Science.gov (United States)

Vuoksimaa, Eero; Panizzon, Matthew S; Franz, Carol E; Fennema-Notestine, Christine; Hagler, Donald J; Lyons, Michael J; Dale, Anders M; Kremen, William S

2018-05-11

Height and general cognitive ability are positively associated, but the underlying mechanisms of this relationship are not well understood. Both height and general cognitive ability are positively associated with brain size. Still, the neural substrate of the height-cognitive ability association is unclear. We used a sample of 515 middle-aged male twins with structural magnetic resonance imaging data to investigate whether the association between height and cognitive ability is mediated by cortical size. In addition to cortical volume, we used genetically, ontogenetically and phylogenetically distinct cortical metrics of total cortical surface area and mean cortical thickness. Height was positively associated with general cognitive ability and total cortical volume and cortical surface area, but not with mean cortical thickness. Mediation models indicated that the well-replicated height-general cognitive ability association is accounted for by individual differences in total cortical volume and cortical surface area (highly heritable metrics related to global brain size), and that the genetic association between cortical surface area and general cognitive ability underlies the phenotypic height-general cognitive ability relationship.

Velocity Segregation and Systematic Biases In Velocity Dispersion Estimates with the SPT-GMOS Spectroscopic Survey

Science.gov (United States)

Bayliss, Matthew. B.; Zengo, Kyle; Ruel, Jonathan; Benson, Bradford A.; Bleem, Lindsey E.; Bocquet, Sebastian; Bulbul, Esra; Brodwin, Mark; Capasso, Raffaella; Chiu, I.-non; McDonald, Michael; Rapetti, David; Saro, Alex; Stalder, Brian; Stark, Antony A.; Strazzullo, Veronica; Stubbs, Christopher W.; Zenteno, Alfredo

2017-03-01

The velocity distribution of galaxies in clusters is not universal; rather, galaxies are segregated according to their spectral type and relative luminosity. We examine the velocity distributions of different populations of galaxies within 89 Sunyaev Zel’dovich (SZ) selected galaxy clusters spanning 0.28GMOS spectroscopic survey, supplemented by additional published spectroscopy, resulting in a final spectroscopic sample of 4148 galaxy spectra—2868 cluster members. The velocity dispersion of star-forming cluster galaxies is 17 ± 4% greater than that of passive cluster galaxies, and the velocity dispersion of bright (m< {m}* -0.5) cluster galaxies is 11 ± 4% lower than the velocity dispersion of our total member population. We find good agreement with simulations regarding the shape of the relationship between the measured velocity dispersion and the fraction of passive versus star-forming galaxies used to measure it, but we find a small offset between this relationship as measured in data and simulations, which suggests that our dispersions are systematically low by as much as 3% relative to simulations. We argue that this offset could be interpreted as a measurement of the effective velocity bias that describes the ratio of our observed velocity dispersions and the intrinsic velocity dispersion of dark matter particles in a published simulation result. Measuring velocity bias in this way suggests that large spectroscopic surveys can improve dispersion-based mass-observable scaling relations for cosmology even in the face of velocity biases, by quantifying and ultimately calibrating them out.

Retrieving Smoke Aerosol Height from DSCOVR/EPIC

Science.gov (United States)

Xu, X.; Wang, J.; Wang, Y.

2017-12-01

Unlike industrial pollutant particles that are often confined within the planetary boundary layer, smoke from forest and agriculture fires can inject massive carbonaceous aerosols into the upper troposphere due to the intense pyro-convection. Sensitivity of weather and climate to absorbing carbonaceous aerosols is regulated by the altitude of those aerosol layers. However, aerosol height information remains limited from passive satellite sensors. Here we present an algorithm to estimate smoke aerosol height from radiances in the oxygen A and B bands measured by the Earth Polychromatic Imaging Camera (EPIC) from the Deep Space Climate Observatory (DSCOVR). With a suit of case studies and validation efforts, we demonstrate that smoke aerosol height can be well retrieved over both ocean and land surfaces multiple times daily.

Five-class height-weight mean and SD system applying Estonian reference values of height-weight mean and SD for systematization of seventeen-year-old conscripts' anthropometric data.

Science.gov (United States)

Lintsi, Mart; Kaarma, Helje; Aunapuu, Marina; Arend, Andres

2007-03-01

A study of 739 conscripts aged 17 years from the town of Tartu and from the Tartu county was performed. Height, weight, 33 anthropometric measurements and 12 skinfolds were measured. The data were classified into five height-weight mean and SD-classes applying the Estonian reference values for this age and sex (Grünberg et al. 1998). There were 3 classes with conformity between height and weight class: 1--small (small height and small weight), 2--medium (medium height and medium weight), 3--large (large height and large weight), 4--weight class dominating (pyknomorphic) and 5--height class dominating (leptomorphic). It was found, that in classes 1, 2 and 3 the height and weight increase was in accordance with the increase in all heights, breadths and depths, circumferences, skinfolds, body fat, muscle and bone mass. In class 4 circumferences, skinfolds, body fat and muscle mass were bigger. In class 5 all heights and the relative bone mass were bigger. The present investigation confirms the assumption that the five height-weight mean and SD five-class system applying the Estonian reference values for classifying the anthropometric variables is suitable for seventeen-year-old conscripts. As well the border values of 5%, 50% and 95% for every anthropometrical variable in the five-classes were calculated, which may be helpful for practical classifying.

Sodium Velocity Maps on Mercury

Science.gov (United States)

Potter, A. E.; Killen, R. M.

2011-01-01

The objective of the current work was to measure two-dimensional maps of sodium velocities on the Mercury surface and examine the maps for evidence of sources or sinks of sodium on the surface. The McMath-Pierce Solar Telescope and the Stellar Spectrograph were used to measure Mercury spectra that were sampled at 7 milliAngstrom intervals. Observations were made each day during the period October 5-9, 2010. The dawn terminator was in view during that time. The velocity shift of the centroid of the Mercury emission line was measured relative to the solar sodium Fraunhofer line corrected for radial velocity of the Earth. The difference between the observed and calculated velocity shift was taken to be the velocity vector of the sodium relative to Earth. For each position of the spectrograph slit, a line of velocities across the planet was measured. Then, the spectrograph slit was stepped over the surface of Mercury at 1 arc second intervals. The position of Mercury was stabilized by an adaptive optics system. The collection of lines were assembled into an images of surface reflection, sodium emission intensities, and Earthward velocities over the surface of Mercury. The velocity map shows patches of higher velocity in the southern hemisphere, suggesting the existence of sodium sources there. The peak earthward velocity occurs in the equatorial region, and extends to the terminator. Since this was a dawn terminator, this might be an indication of dawn evaporation of sodium. Leblanc et al. (2008) have published a velocity map that is similar.

Water velocity meter

Science.gov (United States)

Roberts, C. W.; Smith, D. L.

1970-01-01

Simple, inexpensive drag sphere velocity meter with a zero to 6 ft/sec range measures steady-state flow. When combined with appropriate data acquisition system, it is suited to applications where large numbers of simultaneous measurements are needed for current mapping or velocity profile determination.

Definition of Physical Height Systems for Telluric Planets and Moons

Science.gov (United States)

Tenzer, Robert; Foroughi, Ismael; Sjöberg, Lars E.; Bagherbandi, Mohammad; Hirt, Christian; Pitoňák, Martin

2018-01-01

In planetary sciences, the geodetic (geometric) heights defined with respect to the reference surface (the sphere or the ellipsoid) or with respect to the center of the planet/moon are typically used for mapping topographic surface, compilation of global topographic models, detailed mapping of potential landing sites, and other space science and engineering purposes. Nevertheless, certain applications, such as studies of gravity-driven mass movements, require the physical heights to be defined with respect to the equipotential surface. Taking the analogy with terrestrial height systems, the realization of height systems for telluric planets and moons could be done by means of defining the orthometric and geoidal heights. In this case, however, the definition of the orthometric heights in principle differs. Whereas the terrestrial geoid is described as an equipotential surface that best approximates the mean sea level, such a definition for planets/moons is irrelevant in the absence of (liquid) global oceans. A more natural choice for planets and moons is to adopt the geoidal equipotential surface that closely approximates the geometric reference surface (the sphere or the ellipsoid). In this study, we address these aspects by proposing a more accurate approach for defining the orthometric heights for telluric planets and moons from available topographic and gravity models, while adopting the average crustal density in the absence of reliable crustal density models. In particular, we discuss a proper treatment of topographic masses in the context of gravimetric geoid determination. In numerical studies, we investigate differences between the geodetic and orthometric heights, represented by the geoidal heights, on Mercury, Venus, Mars, and Moon. Our results reveal that these differences are significant. The geoidal heights on Mercury vary from - 132 to 166 m. On Venus, the geoidal heights are between - 51 and 137 m with maxima on this planet at Atla Regio and Beta

Comparison of dust-layer heights from active and passive satellite sensors

Science.gov (United States)

Kylling, Arve; Vandenbussche, Sophie; Capelle, Virginie; Cuesta, Juan; Klüser, Lars; Lelli, Luca; Popp, Thomas; Stebel, Kerstin; Veefkind, Pepijn

2018-05-01

Aerosol-layer height is essential for understanding the impact of aerosols on the climate system. As part of the European Space Agency Aerosol_cci project, aerosol-layer height as derived from passive thermal and solar satellite sensors measurements have been compared with aerosol-layer heights estimated from CALIOP measurements. The Aerosol_cci project targeted dust-type aerosol for this study. This ensures relatively unambiguous aerosol identification by the CALIOP processing chain. Dust-layer height was estimated from thermal IASI measurements using four different algorithms (from BIRA-IASB, DLR, LMD, LISA) and from solar GOME-2 (KNMI) and SCIAMACHY (IUP) measurements. Due to differences in overpass time of the various satellites, a trajectory model was used to move the CALIOP-derived dust heights in space and time to the IASI, GOME-2 and SCIAMACHY dust height pixels. It is not possible to construct a unique dust-layer height from the CALIOP data. Thus two CALIOP-derived layer heights were used: the cumulative extinction height defined as the height where the CALIOP extinction column is half of the total extinction column, and the geometric mean height, which is defined as the geometrical mean of the top and bottom heights of the dust layer. In statistical average over all IASI data there is a general tendency to a positive bias of 0.5-0.8 km against CALIOP extinction-weighted height for three of the four algorithms assessed, while the fourth algorithm has almost no bias. When comparing geometric mean height there is a shift of -0.5 km for all algorithms (getting close to zero for the three algorithms and turning negative for the fourth). The standard deviation of all algorithms is quite similar and ranges between 1.0 and 1.3 km. When looking at different conditions (day, night, land, ocean), there is more detail in variabilities (e.g. all algorithms overestimate more at night than during the day). For the solar sensors it is found that on average SCIAMACHY data

A century of trends in adult human height

DEFF Research Database (Denmark)

Damsgaard, Camilla Trab; Michaelsen, Kim F.; Molbo, Drude

2016-01-01

in adult height over the past century has occurred in South Korean women and Iranian men, who became 20.2 cm (95% credible interval 17.5-22.7) and 16.5 cm (13.3-19.7) taller, respectively. In contrast, there was little change in adult height in some sub-Saharan African countries and in South Asia over...... the century of analysis. The tallest people over these 100 years are men born in the Netherlands in the last quarter of 20th century, whose average heights surpassed 182.5 cm, and the shortest were women born in Guatemala in 1896 (140.3 cm; 135.8-144.8). The height differential between the tallest...... and shortest populations was 19-20 cm a century ago, and has remained the same for women and increased for men a century later despite substantial changes in the ranking of countries....

Evolution of Human Body Height and Its Implications in Ergonomics

Directory of Open Access Journals (Sweden)

İzzet DUYAR

2009-06-01

Full Text Available Body height is an crucial variable in the design and production of all physical spaces, primarily in the manifacturing of clothes and means of transportation. Having such an ergonomic significance, the height of the human being has constantly changed during the course of history. There exist strong data suggesting that this change is still continue. To find out stages of evolution of human height throughout the ages up to the present will help us to illuminate the human-environment relations, and to predict the possible changes that the human height might be subjected to in the future. In view of these reasons, the changes that has occured in human height from the period at which hominids appeared until humans’ transition into settled life have been closely examined. The study was carried out on the basis of the data obtained from the earlier studies in literature. These data, when considered as a whole, reveal that the human height did not continuously increase in a linear fashion in its evolutionary path but recorded some increases and decreases at different stages. The difference between males and females (sexual dimorphism has not shown a steady decrease either; instead, it has exhibited an oscillating pattern. The modern humans as a species is not unique in terms of their height; as a matter of fact, two million years ago hominids had existed at approximately the same height as the Homo sapiens. Although the average height had shown some decrease in Homo erectus, its distribution pattern was not much different than the one observed in the modern human societies. In the findings dated to the early stages of the Upper Paleolithic Age, height showed a tendency to increase again

Comparison of the Force-, Velocity- and Power-Time Curves Between the Concentric-Only and Eccentric-Concentric Bench Press Exercises.

Science.gov (United States)

Pérez-Castilla, Alejandro; Comfort, Paul; McMahon, John J; Pestaña-Melero, Francisco Luis; García-Ramos, Amador

2018-01-17

The aim of this study was to compare the temporal and mechanical variables between the concentric-only and eccentric-concentric bench press (BP) variants. Twenty-one men (age: 22.0±4.2 years, body mass: 73.4±7.7 kg, height: 177.2±8.0 cm; one-repetition maximum [1RM]: 1.12±0.12 kg⋅kg) were evaluated during the concentric-only and eccentric-concentric BP variants using 80% 1RM. Temporal (concentric phase duration, propulsive phase duration, and time to reach the maximum values of force, velocity, and power) and mechanical variables (force, velocity, and power), determined using a linear velocity transducer, were compared between both BP variants. All temporal variables were significantly lower during the eccentric-concentric BP compared to the concentric-only BP (P velocity and power were significantly higher for the eccentric-concentric BP compared to the concentric-only BP (all P velocity (ES: 0.40) and power (ES: 0.41). The stretch-shortening cycle (i.e., eccentric-concentric BP) mainly enhanced force production at the early portion of the concentric phase, but this potentiation effect gradually reduced over the latter part of the movement. Finally, force was higher for the concentric-only BP during 49% of the concentric phase duration. These results suggest that both BP variants should be included during resistance training programs in order to optimize force output at different points of the concentric phase.

A century of trends in adult human height

NARCIS (Netherlands)

Bentham, J. (James); Di Cesare, M. (Mariachiara); Stevens, G.A. (Gretchen A.); Zhou, B. (Bin); Bixby, H. (Honor); Cowan, M. (Melanie); Fortunato, L. (Léa); Bennett, J.E. (James E.); G. Danaei (Goodarz); Hajifathalian, K. (Kaveh); Lu, Y. (Yuan); Riley, L.M. (Leanne M.); Laxmaiah, A. (Avula); Kontis, V. (Vasilis); Paciorek, C.J. (Christopher J.); M. Ezzati (Majid); Abdeen, Z.A. (Ziad A.); Hamid, Z.A. (Zargar Abdul); Abu-Rmeileh, N.M. (Niveen M.); Acosta-Cazares, B. (Benjamin); Adams, R. (Robert); Aekplakorn, W. (Wichai); C.A. Aguilar-Salinas (Carlos A.); C.O. Agyemang (Charles); Ahmadvand, A. (Alireza); W. Ahrens (W.); Al-Hazzaa, H.M. (Hazzaa M.); Al-Othman, A.R. (Amani Rashed); Raddadi, R.A. (Rajaa Al); Ali, M.M. (Mohamed M.); Alkerwi, A. (Ala’a); M. Alvarez-Pedrerol (Mar); Aly, E. (Eman); P. Amouyel (Philippe); A. Amuzu (Antoinette); Andersen, L.B. (Lars Bo); Anderssen, S.A. (Sigmund A.); Anjana, R.M. (Ranjit Mohan); Aounallah-Skhiri, H. (Hajer); Ariansen, I. (Inger); Aris, T. (Tahir); Arlappa, N. (Nimmathota); Arveiler, D. (Dominique); Assah, F.K. (Felix K.); Avdicová, M. (Mária); J. Azizi (Joshan); Babu, B.V. (Bontha V.); Bahijri, S. (Suhad); Balakrishna, N. (Nagalla); Bandosz, P. (Piotr); Banegas, J.R. (José R.); Barbagallo, C.M. (Carlo M.); Barceló, A. (Alberto); Barkat, A. (Amina); Barros, M.V. (Mauro V.); Bata, I. (Iqbal); Batieha, A.M. (Anwar M.); Batista, R.L. (Rosangela L.); Baur, L.A. (Louise A.); Beaglehole, R. (Robert); Romdhane, H.B. (Habiba Ben); Benet, M. (Mikhail); Bernabe-Ortiz, A. (Antonio); Bernotiene, G. (Gailute); Bettiol, H. (Heloisa); Bhagyalaxmi, A. (Aroor); Bharadwaj, S. (Sumit); Bhargava, S.K. (Santosh K.); Bhatti, Z. (Zaid); Z.A. Bhutta (Zulfiqar A); Bi, H. (Hongsheng); Bi, Y. (Yufang); Bjerregaard, P. (Peter); Bjertness, E. (Espen); Bjertness, M.B. (Marius B.); Björkelund, C. (Cecilia); Blokstra, A. (Anneke); Bo, S. (Simona); M. Bobak (Martin); Boddy, L.M. (Lynne M.); B.O. Boehm (Bernhard); H. Boeing (Heiner); Boissonnet, C.P. (Carlos P.); Bongard, V. (Vanina); P. Bovet (Pascal); Braeckman, L. (Lutgart); Bragt, M.C.E. (Marjolijn C. E.); Brajkovich, I. (Imperia); Branca, F. (Francesco); Breckenkamp, J. (Juergen); H. Brenner (Hermann); L.M. Brewster (Lizzy); Brian, G.R. (Garry R.); Bruno, G. (Graziella); Bueno-de-Mesquita, H.B. (H. Bas); Bugge, A. (Anna); Burns, C. (Con); De León, A.C. (Antonio Cabrera); Cacciottolo, J. (Joseph); Cama, T. (Tilema); Cameron, C. (Christine); Camolas, J. (José); G. Can (Günay); Cândido, A.P.C. (Ana Paula C.); Capuano, V. (Vincenzo); Cardoso, V.C. (Viviane C.); Carlsson, A.C. (Axel C.); Carvalho, M.J. (Maria J.); Casanueva, F.F. (Felipe F.); J.P. Casas (Juan Pablo); Caserta, C.A. (Carmelo A.); Chamukuttan, S. (Snehalatha); A.W.M. Chan (Angelique); Chan, Q. (Queenie); Chaturvedi, H.K. (Himanshu K.); Chaturvedi, N. (Nishi); Chen, C.-J. (Chien-Jen); Chen, F. (Fangfang); Chen, H. (Huashuai); Chen, S. (Shuohua); Chen, Z. (Zhengming); Cheng, C.-Y. (Ching-Yu); A. Chetrit (Angela); Chiolero, A. (Arnaud); Chiou, S.-T. (Shu-Ti); Chirita-Emandi, A. (Adela); Cho, B. (Belong); Cho, Y. (Yumi); Christensen, K. (Kaare); Chudek, J. (Jerzy); R. Cifkova (Renata); F. Claessens; E. Clays (Els); Concin, H. (Hans); C. Cooper (Charles); Cooper, R. (Rachel); Coppinger, T.C. (Tara C.); Costanzo, S. (Simona); D. Cottel (Dominique); Cowell, C. (Chris); Craig, C.L. (Cora L.); Crujeiras, A.B. (Ana B.); D’Arrigo, G. (Graziella); d’Orsi, E. (Eleonora); J. Dallongeville; Damasceno, A. (Albertino); Damsgaard, C.T. (Camilla T.); Dankner, R. (Rachel); Dauchet, L. (Luc); G. De Backer (Guy); D. De Bacquer (Dirk); de Gaetano, G. (Giovanni); De Henauw, S. (Stefaan); D. De Smedt (Delphine); Deepa, M. (Mohan); Deev, A.D. (Alexander D.); A. Dehghan (Abbas); Delisle, H. (Hélène); Delpeuch, F. (Francis); Deschamps, V. (Valérie); K. Dhana (Klodian); Di Castelnuovo, A.F. (Augusto F.); Dias-da-Costa, J.S. (Juvenal Soares); Diaz, A. (Alejandro); Djalalinia, S. (Shirin); Do, H.T.P. (Ha T. P.); Dobson, A.J. (Annette J.); C. Donfrancesco (Chiara); Donoso, S.P. (Silvana P.); A. Döring (Angela); Doua, K. (Kouamelan); Drygas, W. (Wojciech); Dzerve, V. (Vilnis); Egbagbe, E.E. (Eruke E.); Eggertsen, R. (Robert); U. Ekelund (Ulf); El Ati, J. (Jalila); P. Elliott (Paul); Engle-Stone, R. (Reina); Erasmus, R.T. (Rajiv T.); Erem, C. (Cihangir); Eriksen, L. (Louise); Escobedo-de la Peña, J. (Jorge); A. Evans (Alun); Faeh, D. (David); Fall, C.H. (Caroline H.); F. Farzadfar (Farshad); Felix-Redondo, F.J. (Francisco J.); Ferguson, T.S. (Trevor S.); Fernández-Bergés, D. (Daniel); Ferrante, D. (Daniel); Ferrari, M. (Marika); Ferreccio, C. (Catterina); J. Ferrieres (Jean); Finn, J.D. (Joseph D.); K. Fischer (Krista); Flores, E.M. (Eric Monterubio); Föger, B. (Bernhard); Foo, L.H. (Leng Huat); Forslund, A.-S. (Ann-Sofie); Forsner, M. (Maria); S.P. Fortmann (Stephen); Fouad, H.M. (Heba M.); Francis, D.K. (Damian K.); Do Carmo Franco, M. (Maria); O.H. Franco (Oscar); Frontera, G. (Guillermo); Fuchs, F.D. (Flavio D.); Fuchs, S.C. (Sandra C.); Fujita, Y. (Yuki); Furusawa, T. (Takuro); Gaciong, Z. (Zbigniew); Gafencu, M. (Mihai); Gareta, D. (Dickman); Garnett, S.P. (Sarah P.); J.-M. Gaspoz (Jean-Michel); Gasull, M. (Magda); Gates, L. (Louise); J.M. Geleijnse (Marianne); Ghasemian, A. (Anoosheh); S. Giampaoli (Simona); F. Gianfagna (Francesco); Giovannelli, J. (Jonathan); A. Giwercman (Aleksander); Goldsmith, R.A. (Rebecca A.); Gonçalves, H. (Helen); M. Gross; González Rivas, J.P. (Juan P.); Gorbea, M.B. (Mariano Bonet); Gottrand, F. (Frederic); Graff-Iversen, S. (Sidsel); Grafnetter, D. (Dušan); Grajda, A. (Aneta); Grammatikopoulou, M.G. (Maria G.); Gregor, R.D. (Ronald D.); T. Grodzicki (Tomasz); Grøntved, A. (Anders); Gruden, G. (Grabriella); Grujic, V. (Vera); Gu, D. (Dongfeng); Gualdi-Russo, E. (Emanuela); Guan, O.P. (Ong Peng); V. Gudnason (Vilmundur); Guerrero, R. (Ramiro); I. Guessous (Idris); Guimaraes, A.L. (Andre L.); Gulliford, M.C. (Martin C.); Gunnlaugsdottir, J. (Johanna); Gunter, M. (Marc); Guo, X. (Xiuhua); Guo, Y. (Yin); Gupta, P.C. (Prakash C.); Gureje, O. (Oye); Gurzkowska, B. (Beata); Gutierrez, L. (Laura); Gutzwiller, F. (Felix); J. Halkjær; Hambleton, I.R. (Ian R.); R. Hardy; Kumar, R.H. (Rachakulla Hari); Hata, J. (Jun); Hayes, A.J. (Alison J.); He, J. (Jiang); M.E. Hendriks (Marleen); Cadena, L.H. (Leticia Hernandez); Herrala, S. (Sauli); Heshmat, R. (Ramin); Hihtaniemi, I.T. (Ilpo Tapani); Ho, S.Y. (Sai Yin); Ho, S.C. (Suzanne C.); Hobbs, M. (Michael); Hofman, A. (Albert); Hormiga, C.M. (Claudia M.); Horta, B.L. (Bernardo L.); Houti, L. (Leila); Howitt, C. (Christina); Htay, T.T. (Thein Thein); Htet, A.S. (Aung Soe); Htike, M.M.T. (Maung Maung Than); Hu, Y. (Yonghua); A. Husseini (Abdullatif); Huu, C.N. (Chinh Nguyen); Huybrechts, I. (Inge); Hwalla, N. (Nahla); L. Iacoviello (Licia); Iannone, A.G. (Anna G.); Ibrahim, M.M. (Mohsen M.); Ikeda, N. (Nayu); M.A. Ikram (Arfan); V. Irazola (Vilma); M. Islam (Muhammad); Ivkovic, V. (Vanja); Iwasaki, M. (Masanori); Jackson, R.T. (Rod T.); Jacobs, J.M. (Jeremy M.); T.H. Jafar (Tazeen); Jamil, K.M. (Kazi M.); K. Jamrozik; Janszky, I. (Imre); Jasienska, G. (Grazyna); Jelakovic, B. (Bojan); Jiang, C.Q. (Chao Qiang); Joffres, M. (Michel); M. Johansson (Mattias); J.B. Jonas (Jost B.); T. Jorgensen (Torben); Joshi, P. (Pradeep); Juolevi, A. (Anne); Jurak, G. (Gregor); Jureša, V. (Vesna); R. Kaaks (Rudolf); Kafatos, A. (Anthony); Kalter-Leibovici, O. (Ofra); Kapantais, E. (Efthymios); Kasaeian, A. (Amir); Katz, J. (Joanne); Kaur, P. (Prabhdeep); M. Kavousi (Maryam); M. Keil (Mark); Boker, L.K. (Lital Keinan); S. Keinanen-Kiukaanniemi (Sirkka); Kelishadi, R. (Roya); H.C.G. Kemper; A.P. Kengne (Andre Pascal); Kersting, M. (Mathilde); T. Key (Tim); Y.S. Khader (Yousef Saleh); D. Khalili (Davood); Khang, Y.-H. (Young-Ho); K.-T. Khaw (Kay-Tee); Khouw, I.M.S.L. (Ilse M. S. L.); S. Kiechl (Stefan); Killewo, J. (Japhet); Kim, J. (Jeongseon); Klimont, J. (Jeannette); J. Klumbiene (Jurate); Koirala, B. (Bhawesh); Kolle, E. (Elin); P. Kolsteren (Patrick); Korrovits, P. (Paul); S. Koskinen (Seppo); Kouda, K. (Katsuyasu); Koziel, S. (Slawomir); W. Kratzer (Wolfgang); Krokstad, S. (Steinar); Kromhout, D. (Daan); Kruger, H.S. (Herculina S.); R. Kubinova; U.M. Kujala (Urho); Kula, K. (Krzysztof); Kulaga, Z. (Zbigniew); Krishna Kumar, R.; Kurjata, P. (Pawel); Kusuma, Y.S. (Yadlapalli S.); K. Kuulasmaa (Kari); Kyobutungi, C. (Catherine); Laamiri, F.Z. (Fatima Zahra); T. Laatikainen (Tiina); C. Lachat (Carl); Laid, Y. (Youcef); Lam, T.H. (Tai Hing); Landrove, O. (Orlando); Lanska, V. (Vera); Lappas, G. (Georg); Larijani, B. (Bagher); L.E. Laugsand (Lars E.); Bao, K.L.N. (Khanh Le Nguyen); Le, T.D. (Tuyen D.); Leclercq, C. (Catherine); J.J.M. Lee (Jeannette); Lee, J. (Jeonghee); T. Lehtimäki (Terho); Lekhraj, R. (Rampal); León-Muñoz, L.M. (Luz M.); Y. Li (Yanping); Lilly, C.L. (Christa L.); W.-Y. Lim (Wei-Yen); Fernanda Lima-Costa, M.; Lin, H.-H. (Hsien-Ho); X. Lin (Xu); A. Linneberg (Allan); L. Lissner (Lauren); Litwin, M. (Mieczyslaw); Liu, J. (Jing); R. Lorbeer (Roberto); P.A. Lotufo (Paulo A); Lozano, J.E. (José Eugenio); Luksiene, D. (Dalia); A. Lundqvist (Annamari); Lunet, N. (Nuno); Lytsy, P. (Per); Ma, G. (Guansheng); Ma, J. (Jun); Machado-Coelho, G.L.L. (George L. L.); Machi, S. (Suka); Maggi, S. (Stefania); D.J. Magliano; Maire, B. (Bernard); Makdisse, M. (Marcia); R. Malekzadeh (Reza); Malhotra, R. (Rahul); Rao, K.M. (Kodavanti Mallikharjuna); S. Malyutina; Y. Manios; Mann, J.I. (Jim I.); Manzato, E. (Enzo); Margozzini, P. (Paula); Markey, O. (Oonagh); P. Marques-Vidal (Pedro); J. Marrugat (Jaume); Martin-Prevel, Y. (Yves); Martorell, R. (Reynaldo); Masoodi, S.R. (Shariq R.); E.B. Mathiesen (Ellisiv); Matsha, T.E. (Tandi E.); Mazur, A. (Artur); Mbanya, J.C.N. (Jean Claude N.); McFarlane, S.R. (Shelly R.); McGarvey, S.T. (Stephen T.); McKee, M. (Martin); S. McLachlan (Stela); McLean, R.M. (Rachael M.); McNulty, B.A. (Breige A.); Yusof, S.M. (Safiah Md); Mediene-Benchekor, S. (Sounnia); A. Meirhaeghe (Aline); C. Meisinger (Christa); Menezes, A.M.B. (Ana Maria B.); Mensink, G.B.M. (Gert B. M.); Meshram, I.I. (Indrapal I.); A. Metspalu (Andres); J. Mi (Jie); K.F. Michaelsen; Mikkel, K. (Kairit); Miller, J.C. (Jody C.); Miquel, J.F. (Juan Francisco); Jaime Miranda, J.; Mišigoj-Durakovic, M. (Marjeta); Mohamed, M.K. (Mostafa K.); K. Mohammad (Kazem); Mohammadifard, N. (Noushin); V. Mohan (Viswanathan); Yusoff, M.F.M. (Muhammad Fadhli Mohd); Molbo, D. (Drude); Møller, N.C. (Niels C.); Molnár, D. (Dénes); Mondo, C.K. (Charles K.); Monterrubio, E.A. (Eric A.); Monyeki, K.D.K. (Kotsedi Daniel K.); Moreira, L.B. (Leila B.); Morejon, A. (Alain); Moreno, L.A. (Luis A.); Morgan, K. (Karen); Mortensen, E.L. (Erik Lykke); G. Moschonis; Mossakowska, M. (Malgorzata); Mostafa, A. (Aya); Mota, J. (Jorge); Motlagh, M.E. (Mohammad Esmaeel); Motta, J. (Jorge); Mu, T.T. (Thet Thet); M.L. Muiesan (Maria Lorenza); M. Müller-Nurasyid (Martina); Murphy, N. (Neil); Mursu, J. (Jaakko); Murtagh, E.M. (Elaine M.); Musa, K.I. (Kamarul Imran); Musil, V. (Vera); Nagel, G. (Gabriele); Nakamura, H. (Harunobu); Námešná, J. (Jana); Nang, E.E.K. (Ei Ei K.); M. Nangia (Monika); Nankap, M. (Martin); Narake, S. (Sameer); E.M. Navarrete-Muñoz; Neal, W.A. (William A.); Nenko, I. (Ilona); Neovius, M. (Martin); Nervi, F. (Flavio); Neuhauser, H.K. (Hannelore K.); Nguyen, N.D. (Nguyen D.); Nguyen, Q.N. (Quang Ngoc); Nieto-Martínez, R.E. (Ramfis E.); Ning, G. (Guang); T. Ninomiya (Toshiharu); Nishtar, S. (Sania); Noale, M. (Marianna); Norat, T. (Teresa); Noto, D. (Davide); Nsour, M.A. (Mohannad Al); O’Reilly, D. (Dermot); Oh, K. (Kyungwon); Olayan, I.H. (Iman H.); Olinto, M.T.A. (Maria Teresa Anselmo); Oltarzewski, M. (Maciej); Omar, M.A. (Mohd A.); A. Onat (Altan); Ordunez, P. (Pedro); Ortiz, A.P. (Ana P.); Osler, M. (Merete); Osmond, C. (Clive); Ostojic, S.M. (Sergej M.); Otero, J.A. (Johanna A.); K. Overvad (Kim); E. Owusu-Dabo (Ellis); Paccaud, F.M. (Fred Michel); Padez, C. (Cristina); Pahomova, E. (Elena); A. Pajak (Andrzej); D. Palli (Domenico); Palloni, A. (Alberto); Palmieri, L. (Luigi); S. Panda-Jonas (Songhomitra); F. Panza (Francesco); Parnell, W.R. (Winsome R.); Parsaeian, M. (Mahboubeh); Pecin, I. (Ivan); Pednekar, M.S. (Mangesh S.); P.H.M. Peeters; Peixoto, S.V. (Sergio Viana); Peltonen, M. (Markku); A. Pereira (A.); Pérez, C.M. (Cynthia M.); A. Peters; Petkeviciene, J. (Janina); Peykari, N. (Niloofar); Pham, S.T. (Son Thai); Pigeot, I. (Iris); H. Pikhart (Hynek); Pilav, A. (Aida); A. Pilotto (Alberto); Pistelli, F. (Francesco); Pitakaka, F. (Freda); Piwonska, A. (Aleksandra); Plans-Rubió, P. (Pedro); Poh, B.K. (Bee Koon); M. Porta; M.L.P. Portegies (Marileen); Poulimeneas, D. (Dimitrios); Pradeepa, R. (Rajendra); Prashant, M. (Mathur); J.F. Price (Jackie F.); Puiu, M. (Maria); M. Punab (Margus); Qasrawi, R.F. (Radwan F.); Qorbani, M. (Mostafa); Bao, T.Q. (Tran Quoc); Radic, I. (Ivana); Radisauskas, R. (Ricardas); Rahman, M.-M. (Mah-mudur); O. Raitakari (Olli); Raj, M. (Manu); Rao, S.R. (Sudha Ramachandra); Ramachandran, A. (Ambady); Ramke, J. (Jacqueline); Ramos, R. (Rafel); Rampal, S. (Sanjay); Rasmussen, F. (Finn); J. Redón (Josep); Reganit, P.F.M. (Paul Ferdinand M.); Ribeiro, R. (Robespierre); Riboli, E. (Elio); Rigo, F. (Fernando); T.F. Rinke de Wit (Tobias); Ritti-Dias, R.M. (Raphael M.); Rivera, J.A. (Juan A.); S.M. Robinson (Siân); Robitaille, C. (Cynthia); F. Rodríguez Artalejo (Fernando); Del Cristo Rodriguez-Perez, M. (María); Rodríguez-Villamizar, L.A. (Laura A.); Rojas-Martinez, R. (Rosalba); Rojroong-Wasinkul, N. (Nipa); Romaguera, D. (Dora); K. Ronkainen (Kimmo); A. Rosengren (Annika); Rouse, I. (Ian); Rubinstein, A. (Adolfo); Rühli, F.J. (Frank J.); Rui, O. (Ornelas); Ruiz-Betancourt, B.S. (Blanca Sandra); Russo Horimoto, A.R.V. (Andrea R. V.); Rutkowski, M. (Marcin); C. Sabanayagam (Charumathi); Sachdev, H.S. (Harshpal S.); Saidi, O. (Olfa); Salanave, B. (Benoit); Martinez, E.S. (Eduardo Salazar); V. Salomaa (Veikko); Salonen, J.T. (Jukka T.); M. Salvetti (Massimo); Sánchez-Abanto, J. (Jose); Sandjaja,; S. Sans (Susana); Santos, D.A. (Diana A.); Santos, O. (Osvaldo); Dos Santos, R.N. (Renata Nunes); Santos, R. (Rute); J. Saramies (Jouko); Sardinha, L.B. (Luis B.); Sarrafzadegan, N. (Nizal); Saum, K.-U. (Kai-Uwe); S. Savva; Scazufca, M. (Marcia); Rosario, A.S. (Angelika Schaffrath); Schargrodsky, H. (Herman); Schienkiewitz, A. (Anja); Schmidt, I.M. (Ida Maria); I.J.C. Schneider (Ione J C); C. Schultsz (Constance); Schutte, A.E. (Aletta E.); Sein, A.A. (Aye Aye); Sen, A. (Abhijit); Senbanjo, I.O. (Idowu O.); S.G. Sepanlou (Sadaf G); Shalnova, S.A. (Svetlana A.); Sharma, S.K. (Sanjib K.); J.E. Shaw; K. Shibuya (Kenji); Shin, D.W. (Dong Wook); Y. Shin (Youchan); R. Shiri (Rahman); R. Siantar (Rosalynn); Sibai, A.M. (Abla M.); Silva, A.M. (Antonio M.); Silva, D.A.S. (Diego Augusto Santos); Simon, M. (Mary); J. Simons (Judith); L.A. Simons (Leon); Sjostrom, M. (Michael); J. Slowikowska-Hilczer (Jolanta); Slusarczyk, P. (Przemyslaw); L. Smeeth (Liam); Smith, M.C. (Margaret C.); M.B. Snijder (Marieke); So, H.-K. (Hung-Kwan); Sobngwi, E. (Eugène); S. Söderberg (Stefan); Soekatri, M.Y.E. (Moesijanti Y. E.); Solfrizzi, V. (Vincenzo); E. Sonestedt (Emily); Song, Y. (Yi); T.I.A. Sørensen (Thorkild); Soric, M. (Maroje); Jérome, C.S. (Charles Sossa); Soumare, A. (Aicha); J.A. Staessen (Jan); Starc, G. (Gregor); Stathopoulou, M.G. (Maria G.); Staub, K. (Kaspar); Stavreski, B. (Bill); Steene-Johannessen, J. (Jostein); Stehle, P. (Peter); Stein, A.D. (Aryeh D.); Stergiou, G.S. (George S.); Stessman, J. (Jochanan); Stieber, J. (Jutta); D. Stöckl (Doris); Stocks, T. (Tanja); Stokwiszewski, J. (Jakub); Stratton, G. (Gareth); K. Stronks (Karien); Strufaldi, M.W. (Maria Wany); Sun, C.-A. (Chien-An); Sundström, J. (Johan); Sung, Y.-T. (Yn-Tz); J. Sunyer (Jordi); Suriyawongpaisal, P. (Paibul); Swinburn, B.A. (Boyd A.); Sy, R.G. (Rody G.); Szponar, L. (Lucjan); E. Shyong Tai; M.L. Tammesoo; A. Tamosiunas (Abdonas); Tang, L. (Line); Tang, X. (Xun); F. Tanser (Frank); Tao, Y. (Yong); Tarawneh, M.R. (Mohammed Rasoul); Tarp, J. (Jakob); Tarqui-Mamani, C.B. (Carolina B.); Taylor, A. (Anne); Tchibindat, F. (Félicité); Theobald, H. (Holger); L. Thijs (Lutgarde); L. Thuesen (Leif); A. Tjønneland (Anne); Tolonen, H.K. (Hanna K.); Tolstrup, J.S. (Janne S.); Topbas, M. (Murat); Topór-Madry, R. (Roman); M. Torrent (Maties); Toselli, S. (Stefania); Traissac, P. (Pierre); A. Trichopoulou (Antonia); Trichopoulos, D. (Dimitrios); Trinh, O.T.H. (Oanh T. H.); Trivedi, A. (Atul); Tshepo, L. (Lechaba); Tulloch-Reid, M.K. (Marshall K.); Tuomainen, T.-P. (Tomi-Pekka); J. Tuomilehto (Jaakko); Turley, M.L. (Maria L.); Tynelius, P. (Per); Tzotzas, T. (Themistoklis); C. Tzourio (Christophe); Ueda, P. (Peter); Ukoli, F.A.M. (Flora A. M.); Ulmer, H. (Hanno); Unal, B. (Belgin); Uusitalo, H.M.T. (Hannu M. T.); Valdivia, G. (Gonzalo); Vale, S. (Susana); D. Valvi (Damaskini); Y.T. van der Schouw (Yvonne); Van Herck, K. (Koen); Van Minh, H. (Hoang); L. van Rossem (Lenie); I. van Valkengoed (Irene); D. Vanderschueren (Dirk); D. Vanuzzo (Diego); L. Vatten (Lars); Vega, T. (Tomas); Velasquez-Melendez, G. (Gustavo); G. Veronesi (Giovanni); Monique Verschuren, W.M.; Verstraeten, R. (Roosmarijn); Victora, C.G. (Cesar G.); G. Viegi; L. Viet (Lucie); E. Viikari-Juntura (Eira); P. Vineis (Paolo); J. Vioque (Jesus); Virtanen, J.K. (Jyrki K.); S. Visvikis-Siest (Sophie); B. Viswanathan (Bharathi); P. Vollenweider (Peter); Voutilainen, S. (Sari); Vrdoljak, A. (Ana); M. Vrijheid (Martine); Wade, A.N. (Alisha N.); Wagner, A. (Aline); Walton, J. (Janette); Mohamud, W.N.W. (Wan Nazaimoon Wan); Wang, M.-D. (Ming-Dong); Wang, Q. (Qian); Y. Wang (Ying); Goya Wannamethee, S.; N.J. Wareham (Nick); Weerasekera, D. (Deepa); P.H. Whincup (Peter); Widhalm, K. (Kurt); Widyahening, I.S. (Indah S.); Wiecek, A. (Andrzej); A.H. Wijga (Alet); Wilks, R.J. (Rainford J.); J. Willeit (Johann); T. Wilsgaard (Tom); B. Wojtyniak (Bogdan); Wong, J.E. (Jyh Eiin); Wong, T.Y. (Tien Yin); Woo, J. (Jean); M. Woodward (Mark); F.C.W. Wu (Frederick C.); Wu, J. (Jianfeng); Wu, S.L. (Shou Ling); Xu, H. (Haiquan); Xu, L. (Liang); Yamborisut, U. (Uruwan); Yan, W. (Weili); Yang, X. (Xiaoguang); Yardim, N. (Nazan); X. Ye (Xingwang); P.K. Yiallouros (P.); Yoshihara, A. (Akihiro); You, Q.S. (Qi Sheng); Younger-Coleman, N.O. (Novie O.); Yusoff, A.F. (Ahmad F.); Zainuddin, A.A. (Ahmad A.); Zambon, S. (Sabina); T. Zdrojewski (T.); Zeng, Y. (Yi); Zhao, D. (Dong); Zhao, W. (Wenhua); Y. Zheng (Yingfeng); M. Zhou (Ming); Zhu, D. (Dan); E. Zimmermann; Cisneros, J.Z. (Julio Zuñiga)

2016-01-01

textabstractBeing taller is associated with enhanced longevity, and higher education and earnings. We reanalysed 1472 population-based studies, with measurement of height on more than 18.6 million participants to estimate mean height for people born between 1896 and 1996 in 200 countries. The

Influence of lateral slab edge distance on plate velocity, trench velocity, and subduction partitioning

NARCIS (Netherlands)

Schellart, W. P.; Stegman, D. R.; Farrington, R. J.; Moresi, L.

2011-01-01

Subduction of oceanic lithosphere occurs through both trenchward subducting plate motion and trench retreat. We investigate how subducting plate velocity, trench velocity and the partitioning of these two velocity components vary for individual subduction zone segments as a function of proximity to

Measuring the fill height of sealed cans with a compound pendulum

International Nuclear Information System (INIS)

Rinard, P.M.

1995-06-01

A compound pendulum has been designed, fabricated, tested, and used to determine the fill height of material in sealed cans. The specific cans that stimulated this work are partially filled with uranium and plutonium oxide. Fill height affects nondestructive assays using fission neutrons, but corrections for various fill heights can be made once the height is known. Heights vary with use as the powder compacts or loosens, so it is necessary to determine the height at the time of the neutron measurement. The pendulum is small and readily portable so it can be taken to the location of the neutron measurement. Tests with open cans filled with sand to various known heights had accuracies generally within 3%. Factors that can affect the accuracy are examined and discussed. Experience in using the pendulum on sealed cans is related

Estimation of Total Tree Height from Renewable Resources Evaluation Data

Science.gov (United States)

Charles E. Thomas

1981-01-01

Many ecological, biological, and genetic studies use the measurement of total tree height. Until recently, the Southern Forest Experiment Station's inventory procedures through Renewable Resources Evaluation (RRE) have not included total height measurements. This note provides equations to estimate total height based on other RRE measurements.

Variability of the Mixed-Layer Height Over Mexico City

Science.gov (United States)

García-Franco, J. L.; Stremme, W.; Bezanilla, A.; Ruiz-Angulo, A.; Grutter, M.

2018-06-01

The diurnal and seasonal variability of the mixed-layer height in urban areas has implications for ground-level air pollution and the meteorological conditions. Measurements of the backscatter of light pulses with a commercial lidar system were performed for a continuous period of almost six years between 2011 and 2016 in the southern part of Mexico City. The profiles were temporally and vertically smoothed, clouds were filtered out, and the mixed-layer height was determined with an ad hoc treatment of both the filtered and unfiltered profiles. The results are in agreement when compared with values of mixed-layer height reconstructed from, (i) radiosonde data, and (ii) surface and vertical column densities of a trace gas. The daily maxima of the mean mixed-layer height reach values > 3 km above ground level in the months of March-April, and are clearly lower (behaviour, which is characterized together with the mixed-layer-height anomalies. A clear residual layer is evident from the backscattered signals recorded in days with specific atmospheric conditions, but also from the cloud-filtered mean diurnal profiles. The occasional presence of a residual layer results in an overestimation of the reported mixed-layer height during the night and early morning hours.

A century of trends in adult human height

NARCIS (Netherlands)

Bentham, James; Di Cesare, Mariachiara; Stevens, Gretchen A.; Zhou, Bin; Bixby, Honor; Cowan, Melanie; Fortunato, Léa; Bennett, James E.; Danaei, Goodarz; Hajifathalian, Kaveh; Lu, Yuan; Riley, Leanne M.; Laxmaiah, Avula; Kontis, Vasilis; Paciorek, Christopher J.; Riboli, Elio; Ezzati, Majid; Abdeen, Ziad A.; Hamid, Zargar Abdul; Abu-Rmeileh, Niveen M.; Acosta-Cazares, Benjamin; Adams, Robert; Aekplakorn, Wichai; Aguilar-Salinas, Carlos A.; Agyemang, Charles; Ahmadvand, Alireza; Ahrens, Wolfgang; Al-Hazzaa, Hazzaa M.; Al-Othman, Amani Rashed; Raddadi, Rajaa Al; Ali, Mohamed M.; Alkerwi, Ala'a; Alvarez-Pedrerol, Mar; Aly, Eman; Amouyel, Philippe; Amuzu, Antoinette; Andersen, Lars Bo; Anderssen, Sigmund A.; Anjana, Ranjit Mohan; Aounallah-Skhiri, Hajer; Ariansen, Inger; Aris, Tahir; Arlappa, Nimmathota; Brewster, Lizzy M.; Hendriks, Marleen Elisabeth; Wit, Tobias F. Rinke de; Schultsz, Constance; Snijder, Marieke B.; Stronks, Karien; Valkengoed, Irene Gm van

2016-01-01

Being taller is associated with enhanced longevity, and higher education and earnings. We reanalysed 1472 population-based studies, with measurement of height on more than 18.6 million participants to estimate mean height for people born between 1896 and 1996 in 200 countries. The largest gain in

Neural network cloud top pressure and height for MODIS

Science.gov (United States)

Håkansson, Nina; Adok, Claudia; Thoss, Anke; Scheirer, Ronald; Hörnquist, Sara

2018-06-01

Cloud top height retrieval from imager instruments is important for nowcasting and for satellite climate data records. A neural network approach for cloud top height retrieval from the imager instrument MODIS (Moderate Resolution Imaging Spectroradiometer) is presented. The neural networks are trained using cloud top layer pressure data from the CALIOP (Cloud-Aerosol Lidar with Orthogonal Polarization) dataset. Results are compared with two operational reference algorithms for cloud top height: the MODIS Collection 6 Level 2 height product and the cloud top temperature and height algorithm in the 2014 version of the NWC SAF (EUMETSAT (European Organization for the Exploitation of Meteorological Satellites) Satellite Application Facility on Support to Nowcasting and Very Short Range Forecasting) PPS (Polar Platform System). All three techniques are evaluated using both CALIOP and CPR (Cloud Profiling Radar for CloudSat (CLOUD SATellite)) height. Instruments like AVHRR (Advanced Very High Resolution Radiometer) and VIIRS (Visible Infrared Imaging Radiometer Suite) contain fewer channels useful for cloud top height retrievals than MODIS, therefore several different neural networks are investigated to test how infrared channel selection influences retrieval performance. Also a network with only channels available for the AVHRR1 instrument is trained and evaluated. To examine the contribution of different variables, networks with fewer variables are trained. It is shown that variables containing imager information for neighboring pixels are very important. The error distributions of the involved cloud top height algorithms are found to be non-Gaussian. Different descriptive statistic measures are presented and it is exemplified that bias and SD (standard deviation) can be misleading for non-Gaussian distributions. The median and mode are found to better describe the tendency of the error distributions and IQR (interquartile range) and MAE (mean absolute error) are found

Lucas Heights technology park

International Nuclear Information System (INIS)

1987-01-01

The proposed Lucas Heights Technology Park will pound together the applied research programs of Government, tertiary and industry sectors, aiming to foster technology transfer particularly to the high-technology manufacturing industry. A description of the site is given along with an outline of the envisaged development, existing facilities and expertise. ills

Reduced Height (Rht) Alleles Affect Wheat Grain Quality.

Science.gov (United States)

Casebow, Richard; Hadley, Caroline; Uppal, Rajneet; Addisu, Molla; Loddo, Stefano; Kowalski, Ania; Griffiths, Simon; Gooding, Mike

2016-01-01

The effects of dwarfing alleles (reduced height, Rht) in near isogenic lines on wheat grain quality are characterised in field experiments and related to effects on crop height, grain yield and GA-sensitivity. Alleles included those that conferred GA-insensitivity (Rht-B1b, Rht-B1c, Rht-D1b, Rht-D1c) as well as those that retained GA-sensitivity (rht(tall), Rht8, Rht8 + Ppd-D1a, Rht12). Full characterisation was facilitated by including factors with which the effects of Rht alleles are known to interact for grain yield (i.e. system, [conventional or organic]; tillage intensity [plough-based, minimum or zero]; nitrogen fertilizer level [0-450 kg N/ha]; and genetic backgrounds varying in height [cvs Maris Huntsman, Maris Widgeon, and Mercia]. Allele effects on mean grain weight and grain specific weight were positively associated with final crop height: dwarfing reduced these quality criteria irrespective of crop management or GA-sensitivity. In all but two experiments the effects of dwarfing alleles on grain nitrogen and sulphur concentrations were closely and negatively related to effects on grain yield, e.g. a quadratic relationship between grain yield and crop height manipulated by the GA-insensitive alleles was mirrored by quadratic relationships for nitrogen and sulphur concentrations: the highest yields and most dilute concentrations occurred around 80cm. In one of the two exceptional experiments the GA-insensitive Rht-B1b and Rht-B1c significantly (Pgrain nitrogen concentration in the absence of an effect on yield, and in the remaining experiment the GA-sensitive Rht8 significantly reduced both grain yield and grain nitrogen concentration simultaneously. When Rht alleles diluted grain nitrogen concentration, N:S ratios and SDS-sedimentation volumes were often improved. Hagberg falling number (HFN) was negatively related to crop height but benefits from dwarfing were only seen for GA-insensitive alleles. For HFN, therefore, there was the strongest evidence for

Global Distribution of Planetary Boundary Layer Height Derived from CALIPSO

Science.gov (United States)

Huang, J.

2015-12-01

The global distribution of planetary boundary layer (PBL) height, which was estimated from the attenuated back-scatter observations of Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO), is presented. In general, the PBL is capped by a temperature inversion that tends to trap moisture and aerosols. The gradient of back-scatter observed by lidar is almost always associated with this temperature inversion and the simultaneous decrease of moisture content. Thus, the PBL top is defined as the location of the maximum aerosol scattering gradient, which is analogous to the more conventional thermodynamic definition. The maximum standard deviation method, developed by Jordan et al. (2010), is modified and used to derive the global PBL heights. The derived PBL heights are not only consistent with the results of McGrath-Spangler and Denning (2012) but also agree well with the ground-based lidar measurements. It is found that the correlation between CALIPSO and the ground-based lidar was 0.73. The seasonal mean patterns from 4-year mid-day PBL heights over global are demonstrated. Also it is found that the largest PBL heights occur over the Tibetan Plateau and the coastal areas. The smallest PBL heights appear in the Tarim Basin and the northeast of China during the local winter. The comparison of PBL heights from CALIPSO and ECMWF under different land-cover conditions showed that, over ocean and forest surface, the PBL height estimated from the CALIPSO back-scatter climatology is larger than the ones estimated from ECMWF data. However, the PBL heights from ECMWF, over grass land and bare land surface in spring and summer are larger than the ones from CALIPSO.

Low velocity impact on polymer composite plates in contact with water

Directory of Open Access Journals (Sweden)

Y Kwon

2016-09-01

Full Text Available In this study, composite materials were tested in two different environments to determine the role of Fluid Structure Interaction with composites under a low velocity impact. This was done using a low velocity impact machine and polymer composite plates. The composite is made of laminated symmetrical plain weave E-glass fabrics. The test area of the composite plates is 30.5 cm by 30.5 cm with clamped boundary conditions. The testing was done using a drop weight system to impact the center of the test area. One testing was performed with composite plates in air, called dry impact. The other testing was conducted while composite plates were submerged in water, called wet impact. A Plexiglas box in conjunction with the impact machine was used to keep the top of the composite sample dry while it was submerged in an anechoic water tank, so called water-backed air impact. Output from the tests was recorded using strain gauges and a force impact sensor. The results show that an added mass effect from the water plays a large role in the Fluid Structure Interaction with composites due to the similar densities of water and the composites. The wet impact results in a larger impact force and damage than the dry impact under the same impact condition, i.e., the same impact mass and drop height.

Accurate tool height control by bearing gap adjustment

NARCIS (Netherlands)

Wielen, van der A.M.; Schellekens, P.H.J.; Jaartsveld, F.T.M.

2002-01-01

Face turning of optical surfaces on precision lathes needs high precision tool height adjustment, which may be a difficult and time-consuming task. In this paper we present a new tool adjustment mechanism based on varying the bearing gap height of the hydrostatic bearings present in precision lathe

49 CFR 231.31 - Drawbars for freight cars; standard height.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Drawbars for freight cars; standard height. 231.31... cars; standard height. (a) Except on cars specified in paragraph (b) of this section— (1) On standard gage (561/2-inch gage) railroads, the maximum height of drawbars for freight cars (measured...

A GEOMETRICAL HEIGHT SCALE FOR SUNSPOT PENUMBRAE

International Nuclear Information System (INIS)

Puschmann, K. G.; Ruiz Cobo, B.; MartInez Pillet, V.

2010-01-01

Inversions of spectropolarimetric observations of penumbral filaments deliver the stratification of different physical quantities in an optical depth scale. However, without establishing a geometrical height scale, their three-dimensional geometrical structure cannot be derived. This is crucial in understanding the correct spatial variation of physical properties in the penumbral atmosphere and to provide insights into the mechanism capable of explaining the observed penumbral brightness. The aim of this work is to determine a global geometrical height scale in the penumbra by minimizing the divergence of the magnetic field vector and the deviations from static equilibrium as imposed by a force balance equation that includes pressure gradients, gravity, and the Lorentz force. Optical depth models are derived from the inversion of spectropolarimetric data of an active region observed with the Solar Optical Telescope on board the Hinode satellite. We use a genetic algorithm to determine the boundary condition for the inference of geometrical heights. The retrieved geometrical height scale permits the evaluation of the Wilson depression at each pixel and the correlation of physical quantities at each height. Our results fit into the uncombed penumbral scenario, i.e., a penumbra composed of flux tubes with channeled mass flow and with a weaker and more horizontal magnetic field as compared with the background field. The ascending material is hotter and denser than their surroundings. We do not find evidence of overturning convection or field-free regions in the inner penumbral area analyzed. The penumbral brightness can be explained by the energy transfer of the ascending mass carried by the Evershed flow, if the physical quantities below z = -75 km are extrapolated from the results of the inversion.

Optimizing height presentation for aircraft cockpit displays

Science.gov (United States)

Jordan, Chris S.; Croft, D.; Selcon, Stephen J.; Markin, H.; Jackson, M.

1997-02-01

This paper describes an experiment conducted to investigate the type of display symbology that most effectively conveys height information to users of head-down plan-view radar displays. The experiment also investigated the use of multiple information sources (redundancy) in the design of such displays. Subjects were presented with eight different height display formats. These formats were constructed from a control, and/or one, two, or three sources of redundant information. The three formats were letter coding, analogue scaling, and toggling (spatially switching the position of the height information from above to below the aircraft symbol). Subjects were required to indicate altitude awareness via a four-key, forced-choice keyboard response. Error scores and response times were taken as performance measures. There were three main findings. First, there was a significant performance advantage when the altitude information was presented above and below the symbol to aid the representation of height information. Second, the analogue scale, a line whose length indicated altitude, proved significantly detrimental to performance. Finally, no relationship was found between the number of redundant information sources employed and performance. The implications for future aircraft and displays are discussed in relation to current aircraft tactical displays and in the context of perceptual psychological theory.

Pulse-height defect in single-crystal CVD diamond detectors

Energy Technology Data Exchange (ETDEWEB)

Beliuskina, O.; Imai, N. [The University of Tokyo, Center for Nuclear Study, Wako, Saitama (Japan); Strekalovsky, A.O.; Aleksandrov, A.A.; Aleksandrova, I.A.; Ilich, S.; Kamanin, D.V.; Knyazheva, G.N.; Kuznetsova, E.A.; Mishinsky, G.V.; Pyatkov, Yu.V.; Strekalovsky, O.V.; Zhuchko, V.E. [JINR, Flerov Laboratory of Nuclear Reactions, Dubna, Moscow Region (Russian Federation); Devaraja, H.M. [Manipal University, Manipal Centre for Natural Sciences, Manipal, Karnataka (India); Heinz, C. [II. Physikalisches Institut, Justus-Liebig-Universitaet Giessen, Giessen (Germany); Heinz, S. [II. Physikalisches Institut, Justus-Liebig-Universitaet Giessen, Giessen (Germany); GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Hofmann, S.; Kis, M.; Kozhuharov, C.; Maurer, J.; Traeger, M. [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Pomorski, M. [CEA, LIST, Diamond Sensor Laboratory, CEA/Saclay, Gif-sur-Yvette (France)

2017-02-15

The pulse-height versus deposited energy response of a single-crystal chemical vapor deposition (scCVD) diamond detector was measured for ions of Ti, Cu, Nb, Ag, Xe, Au, and of fission fragments of {sup 252} Cf at different energies. For the fission fragments, data were also measured at different electric field strengths of the detector. Heavy ions have a significant pulse-height defect in CVD diamond material, which increases with increasing energy of the ions. It also depends on the electrical field strength applied at the detector. The measured pulse-height defects were explained in the framework of recombination models. Calibration methods known from silicon detectors were modified and applied. A comparison with data for the pulse-height defect in silicon detectors was performed. (orig.)

The Effects of Microgravity on Seated Height (Spinal Elongation)

Science.gov (United States)

Young, K. S.; Rajulu, S.

2011-01-01

ABSTRACT Many physiological factors, such as spinal elongation, fluid shifts, bone atrophy, and muscle loss, occur during an exposure to a microgravity environment. Spinal elongation is just one of the factors that can also affect the safety and performance of a crewmember while in space. Spinal elongation occurs due to the lack of gravity/compression on the spinal column. This allows for the straightening of the natural spinal curve. There is a possible fluid shift in the inter-vertebral disks that may also result in changes in height. This study aims at collecting the overall change in seated height for crewmembers exposed to a microgravity environment. During previous Programs, Apollo-Soyuz Test Project (ASTP) and Skylab, spinal elongation data was collected from a small number of subjects in a standing posture but were limited in scope. Data from these studies indicated a quick increase in stature during the first few days of weightlessness, after which stature growth reached a plateau resulting in up to a 3% increase of the original measurement [1-5]. However, this data was collected only for crewmembers in standing posture and not in a seated posture. Seated height may have a different effect than standing height due to a change in posture as well as due to a compounded effect of wearing restraints and a potential compression of the gluteal area. Seated height was deemed as a critical measurement in the design of the Constellation Program s (CxP) Crew Exploration Vehicle (CEV), called Orion which is now the point-of-departure vehicle for the Multi-Purpose Crew Vehicle (MPCV) Program; therefore a better understanding of the effects of microgravity on seated height is necessary. Potential changes in seated height that may not have impacted crew accommodation in previous Programs will have significant effects on crew accommodation due to the layout of seats in the Orion.. The current and existing configuration is such that the four crewmembers are stacked two by

Gradient-Based Optimization of Wind Farms with Different Turbine Heights: Preprint

Energy Technology Data Exchange (ETDEWEB)

Stanley, Andrew P. J.; Thomas, Jared; Ning, Andrew; Annoni, Jennifer; Dykes, Katherine; Fleming, Paul

2017-05-08

Turbine wakes reduce power production in a wind farm. Current wind farms are generally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine hub heights. Results indicate that when a farm is optimized for layout and height with two separate height groups, COE can be lowered by as much as 5%-9%, compared to a similar layout and height optimization where all the towers are the same. The COE has the best improvement in farms with high turbine density and a low wind shear exponent.

Sea Surface Height, Absolute, Aviso, 0.25 degrees, Global, Science Quality

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Aviso Absolute Sea Surface Height is the Sea Surface Height Deviation plus the long term mean dynamic height. This is Science Quality data.

APTCARE - Lucas Heights

International Nuclear Information System (INIS)

1986-05-01

This plan details command co-ordination and support responses of Commonwealth and State Authorities in the event of an accident with offsite consequences at the Lucas Heights Research Laboratories. The plan has been prepared by the AAEC Local Liaison Working Party, comprising representatives of the Australian Atomic Energy Commission, NSW Police Department, NSW Board of Fire Commissioners, NSW State Emergency Services and Civil Defence Organisation, NSW Department of Health, NSW Department of Environment and Planning and Sutherland Shire Council

Dog behavior co-varies with height, bodyweight and skull shape.

Science.gov (United States)

McGreevy, Paul D; Georgevsky, Dana; Carrasco, Johanna; Valenzuela, Michael; Duffy, Deborah L; Serpell, James A

2013-01-01

Dogs offer unique opportunities to study correlations between morphology and behavior because skull shapes and body shape are so diverse among breeds. Several studies have shown relationships between canine cephalic index (CI: the ratio of skull width to skull length) and neural architecture. Data on the CI of adult, show-quality dogs (six males and six females) were sourced in Australia along with existing data on the breeds' height, bodyweight and related to data on 36 behavioral traits of companion dogs (n = 8,301) of various common breeds (n = 49) collected internationally using the Canine Behavioral Assessment and Research Questionnaire (C-BARQ). Stepwise backward elimination regressions revealed that, across the breeds, 33 behavioral traits all but one of which are undesirable in companion animals correlated with either height alone (n = 14), bodyweight alone (n = 5), CI alone (n = 3), bodyweight-and-skull shape combined (n = 2), height-and-skull shape combined (n = 3) or height-and-bodyweight combined (n = 6). For example, breed average height showed strongly significant inverse relationships (psensitivity, urination when left alone, dog-directed fear, separation-related problems, non-social fear, defecation when left alone, owner-directed aggression, begging for food, urine marking and attachment/attention-seeking, while bodyweight showed strongly significant inverse relationships (p<0.001) with excitability and being reported as hyperactive. Apart from trainability, all regression coefficients with height were negative indicating that, across the breeds, behavior becomes more problematic as height decreases. Allogrooming increased strongly (p<0.001) with CI and inversely with height. CI alone showed a strong significant positive relationship with self-grooming (p<0.001) but a negative relationship with chasing (p = 0.020). The current study demonstrates how aspects of CI (and therefore brain shape), bodyweight and height co-vary with behavior. The

Optimum hub height of a wind turbine for maximizing annual net profit

International Nuclear Information System (INIS)

Lee, Jaehwan; Kim, Dong Rip; Lee, Kwan-Soo

2015-01-01

Highlights: • Annual Net Profit was proposed to optimize the hub height of a wind turbine. • Procedures of the hub height optimization method were introduced. • Effect of local wind speed characteristics on optimum hub height was illustrated. • Effect of rated power on optimum hub height was negligible in the range 0.75–3 MW. • Rated speed and cut-out speed had great effects on optimum hub height. - Abstract: The optimization method of the hub height, which can ensure the economic feasibility of the wind turbine, is proposed in this study. Annual Net Profit is suggested as an objective function and the optimization procedure is developed. The effects of local wind speed and wind turbine power characteristics on the optimum hub height are investigated. The optimum hub height decreased as the mean wind speed and wind shear exponent increased. Rated power had little effect on optimum hub height; it follows that the economies of scale are negligible in the rated power range of 0.75–3 MW. Among the wind turbine power characteristics, rated speed and cut-out speed most strongly affected the optimum hub height

The Sitting-Height Index of Build, (Body Mass/(Sitting Height3, as an Improvement on the Body Mass Index for Children, Adolescents and Young Adults

Directory of Open Access Journals (Sweden)

Richard Burton

2018-02-01

Full Text Available The body mass index (BMI is unsatisfactory in being affected by both relative leg length and height, and, for use with children and adolescents, therefore needs to be interpreted in relation to age. The sitting-height index of build (body mass/(sitting height3, is largely free of these disadvantages. Furthermore, because that index is independent of relative leg length, the latter can be treated as a separate indicator of nutritional history and health risks. Past studies on white children and adults have shown body mass to be approximately proportional to (sitting height3. Moreover, multiple regression of (body mass1/3 on sitting height and leg length, using year-by-year averages, has indicated that leg length is an insignificant predictor of body mass. The present study used data for individuals, namely 2–20 years old males and females, black as well as white. Regression analysis as above again showed leg length to be an insignificant predictor of body mass, but only above the age of about nine years. However, sitting height is still a stronger predictor of body mass than leg length at all ages. The advantages of the sitting-height index of build for use with young people are confirmed.

Estrogen-mediated Height Control in Girls with Marfan Syndrome.

Science.gov (United States)

Lee, Dong-Yun; Hyun, Hye Sun; Huh, Rimm; Jin, Dong-Kyu; Kim, Duk-Kyung; Yoon, Byung-Koo; Choi, DooSeok

2016-02-01

This study evaluated the efficacy of a stepwise regimen of estradiol valerate for height control in girls with Marfan syndrome. Eight girls with Marfan syndrome who had completed estrogen treatment for height control were included. Estradiol valerate was started at a dose of 2 mg/day, and then was increased. The projected final height was estimated using the initial height percentile (on a disease-specific growth curve for Korean Marfan syndrome [gcPFHt]), and the initial bone age (baPFHt). After the estrogen treatment, the projected final height was compared to the actual final height (FHt). The median baseline chronological and bone age were 10.0 and 10.5 years, respectively. After a median of 36.5 months of treatment, the median FHt (172.6 cm) was shorter than the median gcPFHt (181.0 cm) and baPFHt (175.9 cm). In the six patients who started treatment before the age of 11 years, the median FHt (171.8 cm) was shorter than the median gcPFHt (181.5 cm) and baPFHt (177.4 cm) after treatment. The median differences between the FHt and gcPFHt and baPFHt were 9.2 and 8.3 cm, respectively. In two patients started treatment after the age of 11, the differences between FHt and gcPFHt, and baPFHt after treatment were -4 and 1.4 cm, and -1.2 and 0 cm for each case, respectively. A stepwise increasing regimen of estradiol valerate may be an effective treatment for height control in girls with Marfan syndrome, especially when started under 11 years old.

Accuracy of Jump-Mat Systems for Measuring Jump Height.

Science.gov (United States)

Pueo, Basilio; Lipinska, Patrycja; Jiménez-Olmedo, José M; Zmijewski, Piotr; Hopkins, Will G

2017-08-01

Vertical-jump tests are commonly used to evaluate lower-limb power of athletes and nonathletes. Several types of equipment are available for this purpose. To compare the error of measurement of 2 jump-mat systems (Chronojump-Boscosystem and Globus Ergo Tester) with that of a motion-capture system as a criterion and to determine the modifying effect of foot length on jump height. Thirty-one young adult men alternated 4 countermovement jumps with 4 squat jumps. Mean jump height and standard deviations representing technical error of measurement arising from each device and variability arising from the subjects themselves were estimated with a novel mixed model and evaluated via standardization and magnitude-based inference. The jump-mat systems produced nearly identical measures of jump height (differences in means and in technical errors of measurement ≤1 mm). Countermovement and squat-jump height were both 13.6 cm higher with motion capture (90% confidence limits ±0.3 cm), but this very large difference was reduced to small unclear differences when adjusted to a foot length of zero. Variability in countermovement and squat-jump height arising from the subjects was small (1.1 and 1.5 cm, respectively, 90% confidence limits ±0.3 cm); technical error of motion capture was similar in magnitude (1.7 and 1.6 cm, ±0.3 and ±0.4 cm), and that of the jump mats was similar or smaller (1.2 and 0.3 cm, ±0.5 and ±0.9 cm). The jump-mat systems provide trustworthy measurements for monitoring changes in jump height. Foot length can explain the substantially higher jump height observed with motion capture.

Influence of real and virtual heights on standing balance.

Science.gov (United States)

Cleworth, Taylor W; Horslen, Brian C; Carpenter, Mark G

2012-06-01

Fear and anxiety induced by threatening scenarios, such as standing on elevated surfaces, have been shown to influence postural control in young adults. There is also a need to understand how postural threat influences postural control in populations with balance deficits and risk of falls. However, safety and feasibility issues limit opportunities to place such populations in physically threatening scenarios. Virtual reality (VR) has successfully been used to simulate threatening environments, although it is unclear whether the same postural changes can be elicited by changes in virtual and real threat conditions. Therefore, the purpose of this study was to compare the effects of real and virtual heights on changes to standing postural control, electrodermal activity (EDA) and psycho-social state. Seventeen subjects stood at low and high heights in both real and virtual environments matched in scale and visual detail. A repeated measures ANOVA revealed increases with height, independent of visual environment, in EDA, anxiety, fear, and center of pressure (COP) frequency, and decreases with height in perceived stability, balance confidence and COP amplitude. Interaction effects were seen for fear and COP mean position; where real elicited larger changes with height than VR. This study demonstrates the utility of VR, as simulated heights resulted in changes to postural, autonomic and psycho-social measures similar to those seen at real heights. As a result, VR may be a useful tool for studying threat related changes in postural control in populations at risk of falls, and to screen and rehabilitate balance deficits associated with fear and anxiety. Copyright © 2012 Elsevier B.V. All rights reserved.

Effect of Additional Structure on Effective Stack Height of Gas Dispersion in Atmosphere

Directory of Open Access Journals (Sweden)

Takenobu Michioka

2016-03-01

Full Text Available Wind-tunnel experiments were conducted to evaluate the effect of additional structure (building, sea wall and banking on the effective stack height, which is usually used in safety analyses of nuclear power facilities in Japan. The effective stack heights were estimated with and without the additional structure in addition to the reactor building while varying several conditions such as the source height, the height of additional structure and the distance between the source position and the additional structure. When the source height is equivalent to the reactor building height, the additional structure enhances both the vertical and horizontal gas dispersion widths and decreases the ground gas concentration, and it means that the additional structure does not decrease the effective stack height. When the source height is larger than the reactor height, the additional structures might affect the effective stack height. As the distance between the source and the additional structure decreases, or as the height of the additional structure increases, the structure has a larger effect on the effective stack height.

The critical ionization velocity

International Nuclear Information System (INIS)

Raadu, M.A.

1980-06-01

The critical ionization velocity effect was first proposed in the context of space plasmas. This effect occurs for a neutral gas moving through a magnetized plasma and leads to rapid ionization and braking of the relative motion when a marginal velocity, 'the critical velocity', is exceeded. Laboratory experiments have clearly established the significance of the critical velocity and have provided evidence for an underlying mechanism which relies on the combined action of electron impact ionization and a collective plasma interaction heating electrons. There is experimental support for such a mechanism based on the heating of electrons by the modified two-stream instability as part of a feedback process. Several applications to space plasmas have been proposed and the possibility of space experiments has been discussed. (author)

Impacts of shape and height of upstream roof on airflow and pollutant dispersion inside an urban street canyon.

Science.gov (United States)

Huang, Yuan-Dong; He, Wen-Rong; Kim, Chang-Nyung

2015-02-01

A two-dimensional numerical model for simulating flow and pollutant dispersion in an urban street canyon is firstly developed using the FLUENT code and then validated against the wind tunnel results. After this, the flow field and pollutant dispersion inside an urban street canyon with aspect ratio W/H = 1 are examined numerically considering five different shapes (vaulted, trapezoidal, slanted, upward wedged, and downward wedged roofs) as well as three different roof height to building height ratios (Z H /H = 1/6, 1/3, and 1/2) for the upstream building roof. The results obtained reveal that the shape and height of an upstream roof have significant influences on flow pattern and pollutant distribution in an urban canyon. A large single clockwise vortex is generated in the canyon for the vaulted upstream roof at Z H /H = 1/6, 1/3, and 1/2, the trapezoidal and downward wedged roofs at Z H /H = 1/6 and 1/3, and the slanted and upward wedged roofs at Z H /H = 1/6, while a main clockwise vortex and a secondary counterclockwise vortex are established for the trapezoidal and downward wedged roofs at Z H /H = 1/2 and the slanted and upward wedged roofs at Z H /H = 1/3 and 1/2. In the one-vortex flow regime, the clockwise vortex moves upward and grows in size with increasing upstream roof height for the vaulted, trapezoidal, and downward wedged roofs. In the two-vortex flow regime, the size and rotational velocity of both upper clockwise and lower counterclockwise vortices increase with the upstream roof height for the slanted and upward wedged roofs. At Z H /H = 1/6, the pollution levels in the canyon are close among all the upstream roof shapes studied. At Z H /H = 1/3, the pollution levels in the canyon for the upward wedged roof and slanted roof are much higher than those for the vaulted, trapezoidal, and downward wedged roofs. At Z H /H = 1/2, the lowest pollution level appears in the canyon for the vaulted upstream roof, while

Mexico Geoid Heights (MEXICO97)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for Mexico, and North-Central America, is the MEXICO97 geoid model. The computation used about one million terrestrial and marine gravity...

Relationship between Leg Mass, Leg Composition and Foot Velocity on Kicking Accuracy in Australian Football.

Science.gov (United States)

Hart, Nicolas H; Nimphius, Sophia; Spiteri, Tania; Cochrane, Jodie L; Newton, Robert U

2016-06-01

Kicking a ball accurately over a desired distance to an intended target is arguably the most important skill to acquire in Australian Football. Therefore, understanding the potential mechanisms which underpin kicking accuracy is warranted. The aim of this study was to examine the relationship between leg mass, leg composition and foot velocity on kicking accuracy in Australian Football. Thirty-one Australian Footballers (n = 31; age: 22.1 ± 2.8 years; height: 1.81 ± 0.07 m; weight: 85.1 ± 13.0 kg; BMI: 25.9 ± 3.2) each performed ten drop punt kicks over twenty metres to a player target. Athletes were separated into accurate (n = 15) and inaccurate (n = 16) kicking groups. Leg mass characteristics were assessed using whole body DXA scans. Foot velocity was determined using a ten-camera optoelectronic, three-dimensional motion capture system. Interactions between leg mass and foot velocity evident within accurate kickers only (r = -0.670 to -0.701). Relative lean mass was positively correlated with kicking accuracy (r = 0.631), while no relationship between foot velocity and kicking accuracy was evident in isolation (r = -0.047 to -0.083). Given the evident importance of lean mass, and its interaction with foot velocity for accurate kickers; future research should explore speed-accuracy, impulse-variability, limb co-ordination and foot-ball interaction constructs in kicking using controlled with-in subject studies to examine the effects of resistance training and skill acquisition programs on the development of kicking accuracy. Key pointsAccurate kickers expressed a very strong inverse relationship between leg mass and foot velocity. Inaccurate kickers were unable to replicate this, with greater volatility in their performance, indicating an ability of accurate kickers to mediate foot velocity to compensate for leg mass in order to deliver the ball over the required distance.Accurate kickers exhibited larger quantities of relative lean mass and lower quantities

Examples of Vector Velocity Imaging

DEFF Research Database (Denmark)

Hansen, Peter M.; Pedersen, Mads M.; Hansen, Kristoffer L.

2011-01-01

To measure blood flow velocity in vessels with conventional ultrasound, the velocity is estimated along the direction of the emitted ultrasound wave. It is therefore impossible to obtain accurate information on blood flow velocity and direction, when the angle between blood flow and ultrasound wa...

The SCEC Unified Community Velocity Model (UCVM) Software Framework for Distributing and Querying Seismic Velocity Models

Science.gov (United States)

Maechling, P. J.; Taborda, R.; Callaghan, S.; Shaw, J. H.; Plesch, A.; Olsen, K. B.; Jordan, T. H.; Goulet, C. A.

2017-12-01

Crustal seismic velocity models and datasets play a key role in regional three-dimensional numerical earthquake ground-motion simulation, full waveform tomography, modern physics-based probabilistic earthquake hazard analysis, as well as in other related fields including geophysics, seismology, and earthquake engineering. The standard material properties provided by a seismic velocity model are P- and S-wave velocities and density for any arbitrary point within the geographic volume for which the model is defined. Many seismic velocity models and datasets are constructed by synthesizing information from multiple sources and the resulting models are delivered to users in multiple file formats, such as text files, binary files, HDF-5 files, structured and unstructured grids, and through computer applications that allow for interactive querying of material properties. The Southern California Earthquake Center (SCEC) has developed the Unified Community Velocity Model (UCVM) software framework to facilitate the registration and distribution of existing and future seismic velocity models to the SCEC community. The UCVM software framework is designed to provide a standard query interface to multiple, alternative velocity models, even if the underlying velocity models are defined in different formats or use different geographic projections. The UCVM framework provides a comprehensive set of open-source tools for querying seismic velocity model properties, combining regional 3D models and 1D background models, visualizing 3D models, and generating computational models in the form of regular grids or unstructured meshes that can be used as inputs for ground-motion simulations. The UCVM framework helps researchers compare seismic velocity models and build equivalent simulation meshes from alternative velocity models. These capabilities enable researchers to evaluate the impact of alternative velocity models in ground-motion simulations and seismic hazard analysis applications

Developmental decline in height growth in Douglas-fir.

Science.gov (United States)

Barbara J. Bond; Nicole M. Czarnomski; Clifton Cooper; Michael E. Day; Michael S. Greenwood

2007-01-01

The characteristic decline in height growth that occurs over a tree's lifespan is often called "age-related decline." But is the reduction in height growth in aging trees a function of age or of size? We grafted shoot tips across different ages and sizes of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) trees to determine whether...

A century of trends in adult human height

DEFF Research Database (Denmark)

Damsgaard, Camilla Trab; Michaelsen, Kim F.; Molbo, Drude

2016-01-01

the century of analysis. The tallest people over these 100 years are men born in the Netherlands in the last quarter of 20th century, whose average heights surpassed 182.5 cm, and the shortest were women born in Guatemala in 1896 (140.3 cm; 135.8-144.8). The height differential between the tallest...

Variation of boundary-layer wind spectra with height

DEFF Research Database (Denmark)

Larsén, Xiaoli Guo; Petersen, Erik L.; Larsen, Søren Ejling

2018-01-01

This study revisits the height dependence of the wind speed power spectrum from the synoptic scale to the spectral gap. Measurements from cup anemometers and sonics at heights of 15 m to 244 m are used. The measurements are from one land site, one coastal land‐based site and three offshore sites...... the atmospheric tide. The second finding regards the height dependence of the general spectrum. We describe the dependence through a so‐called effective roughness, which is calculated from wind spectra and represents the energy removal at different frequencies, and thus surface conditions in the footprint areas....... The generalizable spectral properties of winds presented herein may prove useful for validating numerical models....

Relationship between throwing velocity, muscle power, and bar velocity during bench press in elite handball players.

Science.gov (United States)

Marques, Mario C; van den Tilaar, Roland; Vescovi, Jason D; Gonzalez-Badillo, Juan Jose

2007-12-01

The purpose of this study was to examine the relationship between ball-throwing velocity during a 3-step running throw and dynamic strength, power, and bar velocity during a concentric-only bench-press exercise in team-handball players. Fourteen elite senior male team-handball players volunteered to participate. Each volunteer had power and bar velocity measured during a concentric-only bench-press test with 26, 36, and 46 kg, as well as having 1-repetition-maximum (1-RMBP) strength determined. Ball-throwing velocity was evaluated with a standard 3-step running throw using a radar gun. Ball-throwing velocity was related to the absolute load lifted during the 1-RMBP (r = .637, P = .014), peak power using 36 kg (r = .586, P = .028) and 46 kg (r = .582, P = .029), and peak bar velocity using 26 kg (r = .563, P = .036) and 36 kg (r = .625, P = .017). The results indicate that throwing velocity of elite team-handball players is related to maximal dynamic strength, peak power, and peak bar velocity. Thus, a training regimen designed to improve ball-throwing velocity in elite male team-handball players should include exercises that are aimed at increasing both strength and power in the upper body.

Measuring the height-to-height correlation function of corrugation in suspended graphene

International Nuclear Information System (INIS)

Kirilenko, D.A.; Brunkov, P.N.

2016-01-01

Nanocorrugation of 2D crystals is an important phenomenon since it affects their electronic and mechanical properties. The corrugation may have various sources; one of them is flexural phonons that, in particular, are responsible for the thermal conductivity of graphene. A study of corrugation of just the suspended graphene can reveal much of valuable information on the physics of this complicated phenomenon. At the same time, the suspended crystal nanorelief can hardly be measured directly because of high flexibility of the 2D crystal. Moreover, the relief portion related to rapid out-of-plane oscillations (flexural phonons) is also inaccessible by such measurements. Here we present a technique for measuring the Fourier components of the height–height correlation function H(q) of suspended graphene which includes the effect of flexural phonons. The technique is based on the analysis of electron diffraction patterns. The H(q) is measured in the range of wavevectors q≈0.4–4.5 nm"−"1. At the upper limit of this range H(q) does follow the T/κq"4 law. So, we measured the value of suspended graphene bending rigidity κ=1.2±0.4 eV at ambient temperature T≈300 K. At intermediate wave vectors, H(q) follows a slightly weaker exponent than theoretically predicted q"−"3"."1"5 but is closer to the results of the molecular dynamics simulation. At low wave vectors, the dependence becomes even weaker, which may be a sign of influence of charge carriers on the dynamics of undulations longer than 10 nm. The technique presented can be used for studying physics of flexural phonons in other 2D materials. - Highlights: • A technique for measuring free-standing 2D crystal corrugation is proposed. • The height-to-height correlation function of the suspended graphene corrugation is measured. • Various parameters of the intrinsic graphene properties are experimentally determined.

The relationship between tree height and leaf area: sapwood area ratio.

Science.gov (United States)

McDowell, N; Barnard, H; Bond, B; Hinckley, T; Hubbard, R; Ishii, H; Köstner, B; Magnani, F; Marshall, J; Meinzer, F; Phillips, N; Ryan, M; Whitehead, D

2002-06-01

The leaf area to sapwood area ratio (A l :A s ) of trees has been hypothesized to decrease as trees become older and taller. Theory suggests that A l :A s must decrease to maintain leaf-specific hydraulic sufficiency as path length, gravity, and tortuosity constrain whole-plant hydraulic conductance. We tested the hypothesis that A l :A s declines with tree height. Whole-tree A l :A s was measured on 15 individuals of Douglas-fir (Pseudotsuga menziesii var. menziesii) ranging in height from 13 to 62 m (aged 20-450 years). A l :A s declined substantially as height increased (P=0.02). Our test of the hypothesis that A l :A s declines with tree height was extended using a combination of original and published data on nine species across a range of maximum heights and climates. Meta-analysis of 13 whole-tree studies revealed a consistent and significant reduction in A l :A s with increasing height (P<0.05). However, two species (Picea abies and Abies balsamea) exhibited an increase in A l :A s with height, although the reason for this is not clear. The slope of the relationship between A l :A s and tree height (ΔA l :A s /Δh) was unrelated to mean annual precipitation. Maximum potential height was positively correlated with ΔA l :A s /Δh. The decrease in A l :A s with increasing tree size that we observed in the majority of species may be a homeostatic mechanism that partially compensates for decreased hydraulic conductance as trees grow in height.

Spatio-temporal evaluation of plant height in corn via unmanned aerial systems

Science.gov (United States)

Varela, Sebastian; Assefa, Yared; Vara Prasad, P. V.; Peralta, Nahuel R.; Griffin, Terry W.; Sharda, Ajay; Ferguson, Allison; Ciampitti, Ignacio A.

2017-07-01

Detailed spatial and temporal data on plant growth are critical to guide crop management. Conventional methods to determine field plant traits are intensive, time-consuming, expensive, and limited to small areas. The objective of this study was to examine the integration of data collected via unmanned aerial systems (UAS) at critical corn (Zea mays L.) developmental stages for plant height and its relation to plant biomass. The main steps followed in this research were (1) workflow development for an ultrahigh resolution crop surface model (CSM) with the goal of determining plant height (CSM-estimated plant height) using data gathered from the UAS missions; (2) validation of CSM-estimated plant height with ground-truthing plant height (measured plant height); and (3) final estimation of plant biomass via integration of CSM-estimated plant height with ground-truthing stem diameter data. Results indicated a correlation between CSM-estimated plant height and ground-truthing plant height data at two weeks prior to flowering and at flowering stage, but high predictability at the later growth stage. Log-log analysis on the temporal data confirmed that these relationships are stable, presenting equal slopes for both crop stages evaluated. Concluding, data collected from low-altitude and with a low-cost sensor could be useful in estimating plant height.

Reduced Height (Rht Alleles Affect Wheat Grain Quality.

Directory of Open Access Journals (Sweden)

Richard Casebow

Full Text Available The effects of dwarfing alleles (reduced height, Rht in near isogenic lines on wheat grain quality are characterised in field experiments and related to effects on crop height, grain yield and GA-sensitivity. Alleles included those that conferred GA-insensitivity (Rht-B1b, Rht-B1c, Rht-D1b, Rht-D1c as well as those that retained GA-sensitivity (rht(tall, Rht8, Rht8 + Ppd-D1a, Rht12. Full characterisation was facilitated by including factors with which the effects of Rht alleles are known to interact for grain yield (i.e. system, [conventional or organic]; tillage intensity [plough-based, minimum or zero]; nitrogen fertilizer level [0-450 kg N/ha]; and genetic backgrounds varying in height [cvs Maris Huntsman, Maris Widgeon, and Mercia]. Allele effects on mean grain weight and grain specific weight were positively associated with final crop height: dwarfing reduced these quality criteria irrespective of crop management or GA-sensitivity. In all but two experiments the effects of dwarfing alleles on grain nitrogen and sulphur concentrations were closely and negatively related to effects on grain yield, e.g. a quadratic relationship between grain yield and crop height manipulated by the GA-insensitive alleles was mirrored by quadratic relationships for nitrogen and sulphur concentrations: the highest yields and most dilute concentrations occurred around 80cm. In one of the two exceptional experiments the GA-insensitive Rht-B1b and Rht-B1c significantly (P<0.05 reduced grain nitrogen concentration in the absence of an effect on yield, and in the remaining experiment the GA-sensitive Rht8 significantly reduced both grain yield and grain nitrogen concentration simultaneously. When Rht alleles diluted grain nitrogen concentration, N:S ratios and SDS-sedimentation volumes were often improved. Hagberg falling number (HFN was negatively related to crop height but benefits from dwarfing were only seen for GA-insensitive alleles. For HFN, therefore, there

Height, fun and safety in the design of children's playground equipment.

Science.gov (United States)

Wakes, Sarah; Beukes, Amanda

2012-01-01

The study reported in this paper adopted a holistic design approach to investigate issues associated with height related playground injuries from a users' perspective. The main objective was to gain an understanding of the relationship between height and fun so as to establish practical guidelines for addressing the causes of height related injuries whilst maintaining the attributes of playground equipment that children find fun and challenging. Results show that, on the one hand, the risk of injury increases when height is coupled with the use of upper body strength and, on the other hand, that coordination is a greater source of fun and challenge than height for children. Accordingly, it is suggested that the level of risk of injury attached to children's playground equipment can be reduced when the use of lower body strength and coordination are combined with lower free fall heights.

Assessing a Template Matching Approach for Tree Height and Position Extraction from Lidar-Derived Canopy Height Models of Pinus Pinaster Stands

Directory of Open Access Journals (Sweden)

Francesco Pirotti

2010-10-01

Full Text Available In this paper, an assessment of a method using a correlation filter over a lidar-derived digital canopy height model (CHM is presented. The objective of the procedure is to obtain stem density, position, and height values, on a stand with the following characteristics: ellipsoidal canopy shape (Pinus pinaster, even-aged and single-layer structure. The process consists of three steps: extracting a correlation map from CHM by applying a template whose size and shape resembles the canopy to be detected, applying a threshold mask to the correlation map to keep a subset of candidate-pixels, and then applying a local maximum filter to the remaining pixel groups. The method performs satisfactorily considering the experimental conditions. The mean tree extraction percentage is 65% with a coefficient of agreement of 0.4. The mean absolute error of height is ~0.5 m for all plots except one. It can be considered a valid approach for extracting tree density and height in regularly spaced stands (i.e., poplar plantations which are fundamental for extracting related forest parameters such as volume and biomass.

Ethnic differences in trabecular meshwork height by optical coherence tomography.

Science.gov (United States)

Chen, Rebecca I; Barbosa, Diego T; Hsu, Chi-Hsin; Porco, Travis C; Lin, Shan C

2015-04-01

Differences in ocular anatomy may contribute to ethnic differences in glaucoma risk. Because the trabecular meshwork (TM) plays an important role in aqueous outflow, its anatomy in relation to at-risk populations may provide insight into a potential contributor to elevated intraocular pressure and thus to probability of glaucoma development. To investigate whether differences exist in TM height between ethnic groups. This prospective study took place from January 1, 2012, to December 31, 2013. Adult patients who self-reported as being of white, Asian, Hispanic, or African American ethnicity were recruited from ophthalmology clinics at the University of California, San Francisco. The TM height was assessed using spectral-domain anterior segment optical coherence tomography. Trabecular meshwork height was measured from the scleral spur to the Schwalbe line. We hypothesized that ethnicities with a higher prevalence of glaucoma would tend to have shorter TM heights. We collected data from 460 eyes of 291 participants after excluding 34 optical coherence tomographic scans owing to poor image quality. The final sample was 32.2% white, 45.1% Asian, 10.5% African American, and 12.1% Hispanic. There were 64.2% women, and the mean age was 68.1 years. The mean (SD) TM height among all eyes included in the study was 836 (131) μm. The mean (SD) TM height was characterized among white (851 [131] μm), Asian (843 [126] μm), Hispanic (822 [147] μm), and African American (771 [118] μm) persons. Ethnicity was not associated with TM height overall (P = .23, linear mixed regression model). However, the TM heights of African American participants (771 μm) were shorter than those of white (851 μm; adjusted difference 95% CI, -119.8 to -8.1; P = .02) and Asian (843 μm; adjusted difference 95% CI, -117.4 to -10.8; P = .02) participants. Although TM height is not associated with ethnicity overall, African American individuals have shorter TM heights compared with Asian and white

Alaska Geoid Heights (GEOID96)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This 2' x 4' geoid height grid for Alaska is distributed as a GEOID96 model. The computation used 1.1 million terrestrial and marine gravity data held in the...

Optimally combined regional geoid models for the realization of height systems in developing countries - ORG4heights

Science.gov (United States)

Lieb, Verena; Schmidt, Michael; Willberg, Martin; Pail, Roland

2017-04-01

Precise height systems require high-resolution and high-quality gravity data. However, such data sets are sparse especially in developing or newly industrializing countries. Thus, we initiated the DFG-project "ORG4heights" for the formulation of a general scientific concept how to (1) optimally combine all available data sets and (2) estimate realistic errors. The resulting regional gravity field models then deliver the fundamental basis for (3) establishing physical national height systems. The innovative key aspects of the project incorporate the development of a method which links (low- up to mid-resolution) gravity satellite mission data and (high- down to low-quality) terrestrial data. Hereby, an optimal combination of the data utilizing their highest measure of information including uncertainty quantification and analyzing systematic omission errors is pursued. Regional gravity field modeling via Multi-Resolution Representation (MRR) and Least Squares Collocation (LSC) are studied in detail and compared based on their theoretical fundamentals. From the findings, MRR shall be further developed towards implementing a pyramid algorithm. Within the project, we investigate comprehensive case studies in Saudi Arabia and South America, i. e. regions with varying topography, by means of simulated data with heterogeneous distribution, resolution, quality and altitude. GPS and tide gauge records serve as complementary input or validation data. The resulting products include error propagation, internal and external validation. A generalized concept then is derived in order to establish physical height systems in developing countries. The recommendations may serve as guidelines for sciences and administration. We present the ideas and strategies of the project, which combines methodical development and practical applications with high socio-economic impact.

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Analysis of the nature of injuries in victims of fall from height

Directory of Open Access Journals (Sweden)

Magdalena E. Kusior

2017-01-01

Full Text Available Aim of study: To assess the types and extent of injuries sustained by victims of fall from height depending on the height of fall. Material and methods: The study included 338 bodies of victims of fatal falls from different heights (from the 1st to 10th floors who were subjected to medico-legal autopsy at the Department of Forensic Medicine, Jagiellonian University Medical College, between 1995 and 2014. For each individual, selected data were collected including gender, age, body height, injury types and presence of alcohol or other intoxicants in blood. The analysis comprised injuries to the brain, thoracic and abdominal organs, fractures of the skull, extremities, ribs and spine, and fractures of the scapula, clavicle and sternum (considered together. The study focused on determining the frequency of occurrence of different injuries in relation to one another and depending on the height of fall. Results : The number and extent of injuries was found to increase along with the height of fall. Three injury types, including injuries to the mesentery and both kidneys and fractures of upper extremity small bones, were shown to occur from the threshold heights of the 3rd, 4th and 6th floors. Eleven injuries demonstrated a statistically significant correlation with the height of fall. The study also revealed a number of correlations between the frequencies of occurrence of different injuries. Conclusions : Injuries found from the threshold value may suggest the minimal height of fall. The presence of injuries which correlate with increasing height, and the overall number of injuries observed in victims of fall from height, may be useful for inferring the height of the fall.

Physiological pattern of lumbar disc height; Physiologisches Muster lumbaler Bandscheibenhoehen

Energy Technology Data Exchange (ETDEWEB)

Biggemann, M [Radiologische Klinik des Evangelischen Krankenhauses Bethesda, Duisburg (Germany); Frobin, W; Brinckmann, P [Muenster Univ. (Germany). Inst. fuer Experimentelle Biomechanik

1997-07-01

Purpose of this study is to present a new method of quantifying objectively the height of all discs in lateral radiographs of the lumbar spine and of analysing the normal craniocaudal sequence pattern of lumbar disc heights. Methods: The new parameter is the ventrally measured disc height corrected for the dependence on the angle of lordosis by normalisation to mean angles observed in the erect posture of healthy persons. To eliminate radiographic magnification, the corrected ventral height is related to the mean depth of the cranially adjoining vertebra. In this manner lumbar disc heights were objectively measured in young, mature and healthy persons (146 males and 65 females). The craniocaudal sequence pattern was analysed by mean values from all persons and by height differences of adjoining discs in each individual lumbar spine. Results: Mean normative values demonstrated an increase in disc height between L1/L2 and L4/L5 and a constant or decreasing disc height between L4/L5 and L5/S1. However, this `physiological sequence of disc height in the statistical mean` was observed in only 36% of normal males and 55% of normal females. Conclusion: The radiological pattern of the `physiological sequence of lumbar disc height` leads to a relevant portion of false positive pathological results especially at L4/L5. An increase of disc height from L4/L5 to L5/S1 may be normal. The recognition of decreased disc height should be based on an abrupt change in the heights of adjoining discs and not on a deviation from a craniocaudal sequence pattern. (orig.) [Deutsch] Ziel dieser Arbeit ist es, einen neuen Parameter zur objektiven Messung der Hoehen aller auf einer seitlichen Uebersichtsaufnahme der LWS erkennbaren Bandscheiben vorzustellen und die physiologische kraniokaudale Diskushoehensequenz neu zu dokumentieren. Methode: Bei dem neuen Messverfahren wird die Bandscheibenhoehe ventral gemessen, zur Korrektur ihrer Haltungsabhaengigkeit auf Standardwinkel (mittlere Winkel

Experiences of ZAMG on mixing height determination

Energy Technology Data Exchange (ETDEWEB)

Piringer, M. [Zentralanstalt fuer Meteorologie und Geodynamik, ZAMG, Vienna (Austria)

1997-10-01

Temperature inversions in the boundary layer occur quite often, esp. in mountainous terrain by which Austria is covered to a large extent, and can lead to enhanced pollution at the surface because the air volume available for dilution is then vertically limited. The Department of Environmental Meteorology of ZAMG therefore set up several field programs in the past to study such conditions at a variety of sites in Austria, using tethersondes and Sodars. Early investigations aimed at comparing Sodar echo profiles to the tethersonde temperature profiles to derive mixing heights from the Sodar echo structure. More recently, evolving from KONGEX, the `convective boundary layer experiment`, mixing heights calculated for Vienna by the OML model were compared to those derived from radiosonde and tethersonde potential temperature profiles. Results of these investigations will be presented, focussing on the problems when using the different methods. New efforts to derive mixing heights from data were also undertaken and are discussed separately. (au)

Height, Relationship Satisfaction, Jealousy, and Mate Retention

Directory of Open Access Journals (Sweden)

Gayle Brewer

2009-07-01

Full Text Available Male height is associated with high mate value. In particular, tall men are perceived as more attractive, dominant and of a higher status than shorter rivals, resulting in a greater lifetime reproductive success. Female infidelity and relationship dissolution may therefore present a greater risk to short men. It was predicted that tall men would report greater relationship satisfaction and lower jealousy and mate retention behavior than short men. Ninety eight heterosexual men in a current romantic relationship completed a questionnaire. Both linear and quadratic relationships were found between male height and relationship satisfaction, cognitive and behavioral jealousy. Tall men reported greater relationship satisfaction and lower levels of cognitive or behavioral jealousy than short men. In addition, linear and quadratic relationships were found between male height and a number of mate retention behaviors. Tall and short men engaged in different mate retention behaviors. These findings are consistent with previous research conducted in this area detailing the greater attractiveness of tall men.

Dog behavior co-varies with height, bodyweight and skull shape.

Directory of Open Access Journals (Sweden)

Paul D McGreevy

Full Text Available Dogs offer unique opportunities to study correlations between morphology and behavior because skull shapes and body shape are so diverse among breeds. Several studies have shown relationships between canine cephalic index (CI: the ratio of skull width to skull length and neural architecture. Data on the CI of adult, show-quality dogs (six males and six females were sourced in Australia along with existing data on the breeds' height, bodyweight and related to data on 36 behavioral traits of companion dogs (n = 8,301 of various common breeds (n = 49 collected internationally using the Canine Behavioral Assessment and Research Questionnaire (C-BARQ. Stepwise backward elimination regressions revealed that, across the breeds, 33 behavioral traits all but one of which are undesirable in companion animals correlated with either height alone (n = 14, bodyweight alone (n = 5, CI alone (n = 3, bodyweight-and-skull shape combined (n = 2, height-and-skull shape combined (n = 3 or height-and-bodyweight combined (n = 6. For example, breed average height showed strongly significant inverse relationships (p<0.001 with mounting persons or objects, touch sensitivity, urination when left alone, dog-directed fear, separation-related problems, non-social fear, defecation when left alone, owner-directed aggression, begging for food, urine marking and attachment/attention-seeking, while bodyweight showed strongly significant inverse relationships (p<0.001 with excitability and being reported as hyperactive. Apart from trainability, all regression coefficients with height were negative indicating that, across the breeds, behavior becomes more problematic as height decreases. Allogrooming increased strongly (p<0.001 with CI and inversely with height. CI alone showed a strong significant positive relationship with self-grooming (p<0.001 but a negative relationship with chasing (p = 0.020. The current study demonstrates how aspects of CI (and therefore brain shape

The impact of North Atlantic wind and cyclone trends on European precipitation and significant wave height in the Atlantic.

Science.gov (United States)

Trigo, Ricardo M; Valente, Maria A; Trigo, Isabel F; Miranda, Pedro M A; Ramos, Alexandre M; Paredes, Daniel; García-Herrera, Ricardo

2008-12-01

An analysis of the frequency of cyclones and surface wind velocity for the Euro-Atlantic sector is performed by means of an objective methodology. Monthly and seasonal trends of cyclones and wind speed magnitude are computed and trends between 1960 and 2000 evaluated. Results reveal a significant frequency decrease (increase) in the western Mediterranean (Greenland and Scandinavia), particularly in December, February, and March. Seasonal and monthly analysis of wind magnitude trends shows similar spatial patterns. We show that these changes in the frequency of low-pressure centers and the associated wind patterns are partially responsible for trends in the significant height of waves. Throughout the extended winter months (October-March), regions with positive (negative) wind magnitude trends, of up to 5 cm/s/year, often correspond to regions of positive (negative) significant wave height trends. The cyclone and wind speed trends computed for January-March are well matched by the corresponding trends in significant wave height, with February being the month with the highest trends (negative south of lat 50 degrees N up to -3 cm/year, and positive up to 5 cm/year just north of Scotland). Trends in European precipitation are assessed using the Climatic Research Unit data set. The results of the assessment emphasize the link with the corresponding tendencies of cyclone frequencies. Finally, it is shown that these changes are associated, to a large extent, with the preferred phases of major large-scale atmospheric circulation modes, particularly with the North Atlantic Oscillation, the eastern Atlantic pattern, and the Scandinavian pattern.

Isokinetic Extension Strength Is Associated With Single-Leg Vertical Jump Height.

Science.gov (United States)

Fischer, Felix; Blank, Cornelia; Dünnwald, Tobias; Gföller, Peter; Herbst, Elmar; Hoser, Christian; Fink, Christian

2017-11-01

Isokinetic strength testing is an important tool in the evaluation of the physical capacities of athletes as well as for decision making regarding return to sports after anterior cruciate ligament (ACL) reconstruction in both athletes and the lay population. However, isokinetic testing is time consuming and requires special testing equipment. A single-jump test, regardless of leg dominance, may provide information regarding knee extension strength through the use of correlation analysis of jump height and peak torque of isokinetic muscle strength. Cross-sectional study; Level of evidence, 3. A total of 169 patients who underwent ACL reconstruction were included in this study. Isokinetic testing was performed on the injured and noninjured legs. Additionally, a single-leg countermovement jump was performed to assess jump height using a jump accelerometer sensor. Extension strength values were used to assess the association between isokinetic muscle strength and jump height. The sample consisted of 60 female (mean age, 20.8 ± 8.3 years; mean weight, 61.7 ± 6.5 kg; mean height, 167.7 ± 5.3 cm) and 109 male (mean age, 23.2 ± 7.7 years; mean weight, 74.6 ± 10.2 kg; mean height, 179.9 ± 6.9 cm) patients. Bivariate correlation analysis showed an association ( r = 0.56, P jump height and isokinetic extension strength on the noninvolved side as well as an association ( r = 0.52, P jump height (beta = 0.49, P jump height having the strongest impact (beta = 0.49, P jump height. The study population encompassed various backgrounds, skill levels, and activity profiles, which might have affected the outcome. Even after controlling for age and sex, isokinetic strength was still moderately associated with jump height. Therefore, the jump technique and type of sport should be considered in future research.

Gridded 5-day mean sea surface height anomaly and significant wave height from Jason-1 and OSTM/Jason-2 satellites (NODC Accession 0065055)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This accession contains the gridded 5-day mean sea surface height anomaly (SSHA) and Ku Band significant wave height (SWH-KU) observed from Jason-1 and OSTM/Jason-2...

Stereoscopic Roadside Curb Height Measurement using V-Disparity

DEFF Research Database (Denmark)

Matu, Florin-Octavian; Vlaykov, Iskren; Thøgersen, Mikkel

2014-01-01

Managing road assets, such as roadside curbs, is one of the interests of municipalities. As an interesting application of computer vision, this paper proposes a system for automated measurement of the height of the roadside curbs. The developed system uses the spatial information available...... results show that the system can measure the height of the roadside curb with good accuracy and precision....

Improved pulse-height store for A/D conversion

Energy Technology Data Exchange (ETDEWEB)

Casoli, P [Montedel S.p.a., Laben Division, Via Bassini 15, Milano, Italy; Maranesi, P [Politecnico di Milano (Italy). Centro Studi Nucleari E. Fermi

1979-11-15

A new pulse-height store is described. Suitable contrivances improve integral linearity and reduce the differential errors that generally occur at signal amplitudes near the lower threshold. No degradations appear at high rates of input events. The electrical specifications of the pulse-height store are determined through a series of measurements described in the final part of the paper. In order to test the circuit in the most significant way, it has been connected to a fast successive-approximation conversion module which uses the sliding-scale technique for channel width equalisation, thus implementing a complete analog-to-digital converter (ADC) for nuclear spectrometry. The performances of the pulse-height store have been deduced from the behavior of the whole system.

Field Testing of an In-well Point Velocity Probe for the Rapid Characterization of Groundwater Velocity

Science.gov (United States)

Osorno, T.; Devlin, J. F.

2017-12-01

Reliable estimates of groundwater velocity is essential in order to best implement in-situ monitoring and remediation technologies. The In-well Point Velocity Probe (IWPVP) is an inexpensive, reusable tool developed for rapid measurement of groundwater velocity at the centimeter-scale in monitoring wells. IWPVP measurements of groundwater speed are based on a small-scale tracer test conducted as ambient groundwater passes through the well screen and the body of the probe. Horizontal flow direction can be determined from the difference in tracer mass passing detectors placed in four funnel-and-channel pathways through the probe, arranged in a cross pattern. The design viability of the IWPVP was confirmed using a two-dimensional numerical model in Comsol Multiphysics, followed by a series of laboratory tank experiments in which IWPVP measurements were calibrated to quantify seepage velocities in both fine and medium sand. Lab results showed that the IWPVP was capable of measuring the seepage velocity in less than 20 minutes per test, when the seepage velocity was in the range of 0.5 to 4.0 m/d. Further, the IWPVP estimated the groundwater speed with a precision of ± 7%, and an accuracy of ± 14%, on average. The horizontal flow direction was determined with an accuracy of ± 15°, on average. Recently, a pilot field test of the IWPVP was conducted in the Borden aquifer, C.F.B. Borden, Ontario, Canada. A total of approximately 44 IWPVP tests were conducted within two 2-inch groundwater monitoring wells comprising a 5 ft. section of #8 commercial well screen. Again, all tests were completed in under 20 minutes. The velocities estimated from IWPVP data were compared to 21 Point Velocity Probe (PVP) tests, as well as Darcy-based estimates of groundwater velocity. Preliminary data analysis shows strong agreement between the IWPVP and PVP estimates of groundwater velocity. Further, both the IWPVP and PVP estimates of groundwater velocity appear to be reasonable when

A Mobile System for Measuring Water Surface Velocities Using Unmanned Aerial Vehicle and Large-Scale Particle Image Velocimetry

Science.gov (United States)

Chen, Y. L.

2015-12-01

Measurement technologies for velocity of river flow are divided into intrusive and nonintrusive methods. Intrusive method requires infield operations. The measuring process of intrusive methods are time consuming, and likely to cause damages of operator and instrument. Nonintrusive methods require fewer operators and can reduce instrument damages from directly attaching to the flow. Nonintrusive measurements may use radar or image velocimetry to measure the velocities at the surface of water flow. The image velocimetry, such as large scale particle image velocimetry (LSPIV) accesses not only the point velocity but the flow velocities in an area simultaneously. Flow properties of an area hold the promise of providing spatially information of flow fields. This study attempts to construct a mobile system UAV-LSPIV by using an unmanned aerial vehicle (UAV) with LSPIV to measure flows in fields. The mobile system consists of a six-rotor UAV helicopter, a Sony nex5T camera, a gimbal, an image transfer device, a ground station and a remote control device. The activate gimbal helps maintain the camera lens orthogonal to the water surface and reduce the extent of images being distorted. The image transfer device can monitor the captured image instantly. The operator controls the UAV by remote control device through ground station and can achieve the flying data such as flying height and GPS coordinate of UAV. The mobile system was then applied to field experiments. The deviation of velocities measured by UAV-LSPIV of field experiments and handhold Acoustic Doppler Velocimeter (ADV) is under 8%. The results of the field experiments suggests that the application of UAV-LSPIV can be effectively applied to surface flow studies.

Height, zinc and soil-transmitted helminth infections in schoolchildren

DEFF Research Database (Denmark)

de Gier, Brechje; Mpabanzi, Liliane; Vereecken, Kim

2015-01-01

Soil-transmitted helminth (STH) infections and zinc deficiency are often found in low- and middle-income countries and are both known to affect child growth. However, studies combining data on zinc and STH are lacking. In two studies in schoolchildren in Cuba and Cambodia, we collected data...... on height, STH infection and zinc concentration in either plasma (Cambodia) or hair (Cuba). We analyzed whether STH and/or zinc were associated with height for age z-scores and whether STH and zinc were associated. In Cuba, STH prevalence was 8.4%; these were mainly Ascaris lumbricoides and Trichuris...... trichiura infections. In Cambodia, STH prevalence was 16.8%, mostly caused by hookworm. In Cuban children, STH infection had a strong association with height for age (aB-0.438, p = 0.001), while hair zinc was significantly associated with height for age only in STH uninfected children. In Cambodian children...

Childhood height increases the risk of prostate cancer mortality

DEFF Research Database (Denmark)

Aarestrup, J; Gamborg, M; Cook, M B

2015-01-01

cancers. Cox proportional hazards regressions were performed. RESULTS: 630 men had prostate cancer recorded as the underlying cause of death. Childhood height at age 13years was positively associated with prostate cancer-specific mortality (hazard ratio [HR]per z-score=1.2, 95% confidence interval [CI]: 1.1-1.3......). Associations were significant at all other childhood ages. Growth analyses showed that height at age 13years had a stronger association with prostate cancer-specific mortality than height at age 7, suggesting the association at age 7 is largely mediated through later childhood height. The tallest boys at age...... 13years had a significantly worse survival, but only when restricted to a diagnosis at years of age (HRz-score of 1=1.7, 95% CI: 1.3-2.4). These associations were significant at all other childhood ages. Childhood BMI was not associated with prostate cancer mortality or survival. CONCLUSION...

A Correction Equation for Jump Height Measured Using the Just Jump System.

Science.gov (United States)

McMahon, John J; Jones, Paul A; Comfort, Paul

2016-05-01

To determine the concurrent validity and reliability of the popular Just Jump system (JJS) for determining jump height and, if necessary, provide a correction equation for future reference. Eighteen male college athletes performed 3 bilateral countermovement jumps (CMJs) on 2 JJSs (alternative method) that were placed on top of a force platform (criterion method). Two JJSs were used to establish consistency between systems. Jump height was calculated from flight time obtained from the JJS and force platform. Intraclass correlation coefficients (ICCs) demonstrated excellent within-session reliability of the CMJ height measurement derived from both the JJS (ICC = .96, P jump height (0.46 ± 0.09 m vs 0.33 ± 0.08 m) than the force platform (P jump height = (0.8747 × alternative jump height) - 0.0666. The JJS provides a reliable but overestimated measure of jump height. It is suggested, therefore, that practitioners who use the JJS as part of future work apply the correction equation presented in this study to resultant jump-height values.

Comments on deriving the equilibrium height of the stable boundary layer

NARCIS (Netherlands)

Steeneveld, G.J.; Wiel, van de B.J.H.; Holtslag, A.A.M.

2007-01-01

Recently, the equilibrium height of the stable boundary layer received much attention in a series of papers by Zilitinkevich and co-workers. In these studies the stable boundary-layer height is derived in terms of inverse interpolation of different boundary-layer height scales, each representing a

Agronomic characters and lodging resistance of plant height mutants of rice

International Nuclear Information System (INIS)

Zhang Zhonggui; Wu Yuejin; Liu Binmei; Xu Xue; Zhang Lili; Wang Min

2010-01-01

Fourteen plant height mutants of Nipponbare were used to study the effect of plant height on the agronomic characters and lodging resistance. The results indicated that the plant height was positively correlated with spike length, third internode length, height of gravity center, fresh weight of main stem, dry weight of main stem, thousand-grain weight, grain-yield per plant and biological yield, and the second internode length. Meanwhile, plant height played an important role in lodging resistance, it was significantly positively correlated with lodging index and negatively correlated with bending moment and culm type index. The correlation between agronomic characters and lodging resistance showed that several agronomic characters had strong impact on the lodging resistance, such as spike length, height of gravity center, basal internode length ( first and second internode), fresh and dry weight of main stem, dry weight of basal internode, seed setting, thousand-grain weight, grain-weight per plant and biological yield. (authors)

Assessment of forearm and plantar foot load in the elderly using a four-wheeled walker with armrest and the effect of armrest height.

Science.gov (United States)

Ko, Chang-Yong; Kim, Sol-Bi; Choi, Hyuk-Jae; Chang, Yunhee; Kang, Sungjae; Heo, Yoon; Ryu, Jeicheong; Kim, Gyoosuk; Mun, Museong

2014-01-01

Patients with hand and/or wrist pathology are recommended to have a four-wheeled walker with an arm rest (FWW-AR) rather than a standard walker or a standard four-wheeled walker (FWW). However, only a few quantitative studies have been performed to compare upper and lower extremity weight bearing. The aim of this study was to evaluate forearm and foot weight bearing using a FWW-AR and the effect of the armrest height. Eleven elderly women (mean age 80.1±5.3 years; mean height 148.5±4.0 cm; mean weight 51.2±9.0 kg) were enrolled. The subjects walked with an FWW-AR, with the elbow in either 90 degree (D90) or 130 degree (D130) flexion, for a distance of 10 m. Surface electromyographic signals were recorded for the upper, middle, and lower trapezius, anterior deltoid, and erector spinae muscles; walking velocity was measured with the subjects weight bearing on their feet and forearms while walking. Simultaneously, the maximum plantar and forearm loads during walking with an FWW-AR were measured. The normalized foot plantar loads were lower at D90 than at D130, while the normalized forearm load was higher at D90 than at D130 (all P<0.05; left foot, 7.9±0.1 N/kg versus 8.8±0.1 N/kg; right foot, 8.6±0.2 N/kg versus. 9.6±0.1 N/kg; left forearm, 1.8±0.5 N/kg versus 0.8±0.2 N/kg; and right forearm, 2.0±0.5 N/kg versus 1.0±0.2 N/kg, respectively). The surface electromyographic activity of the muscles involved in shoulder elevation and the walking velocity were both lower with the elbow at D90 than at D130 (all P<0.05; left upper trapezius, 98.7%±19.5% versus 132.6%±16.9%; right upper trapezius, 83.4%±10.6% versus 108.1%±10.5%; left anterior deltoid, 94.1%±12.8% versus 158.6%±40.4%; right anterior deltoid, 99.1%±15.0% versus 151.9%±19.4%; and velocity, 0.6±0.1 m/sec versus 0.7±0.1 m/sec, respectively). Weight bearing on the lower extremities is significantly reduced when the upper extremities are supported during walking with an FWW-AR. Furthermore, the

New Finnish growth references for children and adolescents aged 0 to 20 years: Length/height-for-age, weight-for-length/height, and body mass index-for-age.

Science.gov (United States)

Saari, Antti; Sankilampi, Ulla; Hannila, Marja-Leena; Kiviniemi, Vesa; Kesseli, Kari; Dunkel, Leo

2011-05-01

Growth curves require regular updates due to secular trends in linear growth. We constructed contemporary growth curves, assessed secular trends in height, and defined body mass index (BMI) cut-off points for thinness, overweight, and obesity in Finnish children. Mixed cross-sectional/longitudinal data of 73,659 healthy subjects aged 0-20 years (born 1983-2008) were collected from providers in the primary health care setting. Growth references for length/height-for-age, weight-for-length/height, and BMI-for-age were fitted using generalized additive models for location, scale, and shape (GAMLSS). BMI percentile curves passing through BMIs 30, 25, 18.5, 17, and 16 kg/m(2) at the age of 18 years were calculated to define limits for obesity, overweight, and various grades of thinness. Increased length/height-for-age was seen in virtually all age-groups when compared to previous Finnish growth data from 1959 to 1971. Adult height was increased by 1.9 cm in girls and 1.8 cm in boys. The largest increases were seen during the peripubertal years: up to 2.8 cm in girls and 5.6 cm in boys. Median weight-for-length/height had not increased. New Finnish references for length/height-for-age, weight-for-length/height, and BMI-for-age were constructed and should be implemented to monitor growth of children in Finland.

Velocity Dispersions Across Bulge Types

International Nuclear Information System (INIS)

Fabricius, Maximilian; Bender, Ralf; Hopp, Ulrich; Saglia, Roberto; Drory, Niv; Fisher, David

2010-01-01

We present first results from a long-slit spectroscopic survey of bulge kinematics in local spiral galaxies. Our optical spectra were obtained at the Hobby-Eberly Telescope with the LRS spectrograph and have a velocity resolution of 45 km/s (σ*), which allows us to resolve the velocity dispersions in the bulge regions of most objects in our sample. We find that the velocity dispersion profiles in morphological classical bulge galaxies are always centrally peaked while the velocity dispersion of morphologically disk-like bulges stays relatively flat towards the center--once strongly barred galaxies are discarded.

Pulse height model for deuterated scintillation detectors

International Nuclear Information System (INIS)

Wang, Haitang; Enqvist, Andreas

2015-01-01

An analytical model of light pulse height distribution for finite deuterated scintillation detectors is created using the impulse approximation. Particularly, the energy distribution of a scattered neutron is calculated based on an existing collision probability scheme for general cylindrical shaped detectors considering double differential cross-sections. The light pulse height distribution is analytically and numerically calculated by convoluting collision sequences with the light output function for an EJ-315 detector from our measurements completed at Ohio University. The model provides a good description of collision histories capturing transferred neutron energy in deuterium-based scintillation materials. The resulting light pulse height distribution details pulse compositions and their corresponding contributions. It shows that probabilities of neutron collision with carbon and deuterium nuclei are comparable, however the light pulse amplitude due to collisions with carbon nuclei is small and mainly located at the lower region of the light pulse distribution axis. The model can explore those neutron interaction events that generate pulses near or below a threshold that would be imposed in measurements. A comparison is made between the light pulse height distributions given by the analytical model and measurements. It reveals a significant probability of a neutron generating a small light pulse due to collisions with carbon nuclei when compared to larger light pulse generated by collisions involving deuterium nuclei. This model is beneficial to understand responses of scintillation materials and pulse compositions, as well as nuclei information extraction from recorded pulses.

Diagnosis of childhood hypertension: is blood pressure height ratio ...

African Journals Online (AJOL)

Blood pressure was also recorded according to the standard method. Systolic and diastolic blood pressure to height ratio were then calculated. Receiver operating curves was used to assess the ability of systolic blood and diastolic blood pressure height ratio to discriminate childhood prehypertension and hypertension.

Estimation of vector velocity

DEFF Research Database (Denmark)

2000-01-01

Using a pulsed ultrasound field, the two-dimensional velocity vector can be determined with the invention. The method uses a transversally modulated ultrasound field for probing the moving medium under investigation. A modified autocorrelation approach is used in the velocity estimation. The new...

A global boundary-layer height climatology

Energy Technology Data Exchange (ETDEWEB)

Dop, H. van; Krol, M.; Holtslag, B. [Inst. for Marine and Atmospheric Research Utrecht, IMAU, Utrecht (Netherlands)

1997-10-01

In principle the ABL (atmospheric boundary layer) height can be retrieved from atmospheric global circulation models since they contain algorithms which determine the intensity of the turbulence as a function of height. However, these data are not routinely available, or on a (vertical) resolution which is too crude in view of the application. This justifies the development of a separate algorithm in order to define the ABL. The algorithm should include the generation of turbulence by both shear and buoyancy and should be based on readily available atmospheric parameters. There is obviously a wide application for boundary heights in off-line global and regional chemistry and transport modelling. It is also a much used parameter in air pollution meteorology. In this article we shall present a theory which is based on current insights in ABL dynamics. The theory is applicable over land and sea surfaces in all seasons. The theory is (for various reasons) not valid in mountainous areas. In areas where boundary-layer clouds or deep cumulus convection are present the theory does not apply. However, the same global atmospheric circulation models contain parameterizations for shallow and deep convection from which separate estimates can be obtained for the extent of vertical mixing. (au)

Analysis of photosynthate translocation velocity and measurement of weighted average velocity in transporting pathway of crops

International Nuclear Information System (INIS)

Ge Cailin; Luo Shishi; Gong Jian; Zhang Hao; Ma Fei

1996-08-01

The translocation profile pattern of 14 C-photosynthate along the transporting pathway in crops were monitored by pulse-labelling a mature leaf with 14 CO 2 . The progressive spreading of translocation profile pattern along the sheath or stem indicates that the translocation of photosynthate along the sheath or stem proceed with a range of velocities rather than with just a single velocity. The method for measuring the weighted average velocity of photosynthate translocation along the sheath or stem was established in living crops. The weighted average velocity and the maximum velocity of photosynthate translocation along the sheath in rice and maize were measured actually. (4 figs., 3 tabs.)

Determination of Vertical Datum Offset between the Regional and the Global Height Datum

Directory of Open Access Journals (Sweden)

LI Jiancheng

2017-10-01

Full Text Available The unification of the global height datum is a key problem to be solved for geodesy after the unification of global geodetic coordination system and three-dimension spatial datum, and the basis of global spatial information sharing and exchange. In this paper, the theoretical and practical problems of vertical datum offset between the regional height datum and the global height datum are studied. Based on the classical theory of the height system in physical geodesy, the definition of the height datum vertical offset is given, and the rigorous formulas for calculating the vertical offset are derived. The formulas can be used to deduce the three methods of the height datum vertical offset determination. On that basis, the influences of different reference system and reference ellipsoid parameters on the calculation of the vertical offset are analyzed. The results show that the reference system and the ellipsoid parameter conversion are very necessary. At the same time, the height anomaly differences method needs to consider the degree zero correction caused by the inconsistency between gravity potential of the global height datum and the one computed by the model. Based on potential difference approach and the height anomaly difference method, the vertical offset between the China 1985 national height datum and the global height datum corresponding to the normal gravity potential U0 of GRS80, WGS-84 and CGCS2000 reference ellipsoidal from the 152 GPS/leveling points near the origin of Qingdao height origin and the EGM2008, EIGEN-6C4 and SGG-UGM-1 model. The regional datum is 23.1 cm lower than the global datum based on EIGEN-6C4 and WGS-84. When the Gauss-Listing geoid (mean sea surface is selected as the global height datum, the China 1985 national height datum is 21.0 cm higher than the global height datum. The results also show that there are still large differences among the accuracies of the current gravity field models on these GPS

Correlation of right atrial appendage velocity with left atrial appendage velocity and brain natriuretic Peptide.

Science.gov (United States)

Kim, Bu-Kyung; Heo, Jung-Ho; Lee, Jae-Woo; Kim, Hyun-Soo; Choi, Byung-Joo; Cha, Tae-Joon

2012-03-01

Left atrial appendage (LAA) anatomy and function have been well characterized both in healthy and diseased people, whereas relatively little attention has been focused on the right atrial appendage (RAA). We sought to evaluate RAA flow velocity and to compare these parameters with LAA indices and with a study of biomarkers, such as brain natriuretic peptide, among patients with sinus rhythm (SR) and atrial fibrillation (AF). In a series of 79 consecutive patients referred for transesophageal echocardiography, 43 patients (23 with AF and 20 controls) were evaluated. AF was associated with a decrease in flow velocity for both LAA and RAA [LAA velocity-SR vs. AF: 61 ± 22 vs. 29 ± 18 m/sec (p vs. AF: 46 ± 20 vs. 19 ± 8 m/sec (p brain natriuretic peptide (BNP). AF was associated with decreased RAA and LAA flow velocities. RAA velocity was found to be positively correlated with LAA velocity and negatively correlated with BNP. The plasma BNP concentration may serve as a determinant of LAA and RAA functions.

Rayleigh Wave Group Velocity Tomography from Microseisms in the Acambay Graben

Science.gov (United States)

Valderrama Membrillo, S.; Aguirre, J.; Zuñiga-Davila, R.; Iglesias, A.

2017-12-01

The Acambay graben is one of the most outstanding structures of the Trans-Mexican Volcanic Belt. The Acambay graben has a length of 80km and 15 to 18 km wide and reaches a maximum height of 400 m in its central part. We obtained the group velocity seismic tomography for the Acamaby graben for three different frequencies (f = 0.1, 0.2 and 0.3 Hz). The graben was divided into 6x6 km cells for the tomography and covered a total area of 1008 km2. Seismic noise data from 10 broadband seismic stations near the Acambay graben were used to extract the surface wave arrival-times between all station pairs. The Green's function was recovered in each stations pair by cross-correlation technique. This technique was applied to seismic recordings collected on the vertical component of 10 broadband stations for a continuous recording period of 5 months. Data processing consisted of removing instrumental response, mean, and trend. After that, we applied time domain normalization, a spectral whitening and applied band-pas filtering of 0.1 to 1 Hz. There are shallow studies of the Acambay graben. But little is known of the distribution of deep graben structures. This study estimated the surface wave velocity deep structure. The structures at the frequency 0.3 Hz indicate a lower depth than the remaining frequencies. The result for this frequency show consistencies with previous studies of gravimetry and resistivity, also defines the fault system of Temascalcingo.

Generalized height-diameter models for Populus tremula L. stands

African Journals Online (AJOL)

USER

2010-07-12

Jul 12, 2010 ... and stand density) into the base height-diameter models increased the accuracy of prediction for P. tremula. .... parameter estimates compared with those obtained with ... using coefficient of determination for non-linear regression (. 2. R ), ..... stochastic height-diameter model for maritime pine ecoregions in.

The Analysis of Height System Definition and the High Precision GNSS Replacing Leveling Method

Directory of Open Access Journals (Sweden)

ZHANG Chuanyin

2017-08-01

Full Text Available Based on the definition of height system, the gravitational equipotential property of height datum surface is discussed in this paper, differences of the heights at ground points that defined in different height systems are tested and analyzed as well. A new method for replacing leveling using GNSS is proposed to ensure the consistency between GNSS replacing leveling and spirit leveling at mm accuracy level. The main conclusions include:①For determining normal height at centimeter accuracy level, the datum surface of normal height should be the geoid. The 1985 national height datum of China adopts normal height system, its datum surface is the geoid passing the Qingdao zero point.②The surface of equi-orthometric height in the near earth space is parallel to the geoid. The combination of GNSS precise positioning and geoid model can be directly used for orthometric height determination. However, the normal height system is more advantageous for describing the terrain and relief.③Based on the proposed method of GNSS replacing leveling, the errors in geodetic height affect more on normal height result than the errors of geoid model, the former is about 1.5 times of the latter.

The association between Helicobacter pylori infection and adult height

International Nuclear Information System (INIS)

Moayyedi, Paul; Forman, David; Duffett, Sara; Mason, Su; Brown, Julia; Crocombe, Will; Feltbower, Richard; Axon, Anthony

2005-01-01

Objectives: A cross-sectional survey was performed to evaluate the association between H. pylori and adult height. Methods: H. pylori infection was assessed using a 13 C-urea breath test and height measured by a research nurse using a stadiometer in participants between the ages of 40-49 years. Results: Height was measured in 2932/3682 participants that attended and were evaluable. H. pylori infected women were 1.4 cm shorter than uninfected women (95% confidence interval, CI=0.7-2.1 cm) and this statistically significant difference persisted after adjusting for age, ethnicity, childhood and present socio-economic status (H. pylori positives 0.79 cm shorter; 95%CI: 0.05-1.52 cm). H. pylori positive men were 0.7 cm shorter than uninfected men but this did not reach statistical significance (95% CI: -0.1-1.5 cm). Conclusion: Although H. pylori infection is associated with reduced adult height in women, this maybe due to residual confounding

Observing Crop-Height Dynamics Using a UAV

Science.gov (United States)

Ziliani, M. G.; Parkes, S. D.; McCabe, M.

2017-12-01

Retrieval of vegetation height during a growing season is a key indicator for monitoring crop status, offering insight to the forecast yield relative to previous planting cycles. Improvement in Unmanned Aerial Vehicle (UAV) technologies, supported by advances in computer vision and photogrammetry software, has enabled retrieval of crop heights with much higher spatial resolution and coverage. These methodologies retrieve a Digital Surface Map (DSM), which combine terrain and crop elements to obtain a Crop Surface Map (CSM). Here we describe an automated method for deriving high resolution CSMs from a DSM, using RGB imagery from a UAV platform. Importantly, the approach does not require the need for a digital terrain map (DTM). The method involves distinguishing between vegetation and bare-ground cover pixels, using vegetation index maps from the RGB orthomosaic derived from the same flight as the DSM. We show that the absolute crop height can be extracted to within several centimeters, exploiting the data captured from a single UAV flight. In addition, the method is applied across five surveys during a maize growing cycle and compared against a terrain map constructed from a baseline UAV survey undertaken prior to crop growth. Results show that the approach is able to reproduce the observed spatial variability of the crop height within the maize field throughout the duration of the growing season. This is particularly valuable since it may be employed to detect intra-field problems (i.e. fertilizer variability, inefficiency in the irrigation system, salinity etc.) at different stages of the season, from which remedial action can be initiated to mitigate against yield loss. The method also demonstrates that UAV imagery combined with commercial photogrammetry software can determine a CSM from a single flight without the requirement of a prior DTM. This, together with the dynamic crop height estimation, provide useful information with which to inform precision

Online Wavelet Complementary velocity Estimator.

Science.gov (United States)

Righettini, Paolo; Strada, Roberto; KhademOlama, Ehsan; Valilou, Shirin

2018-02-01

In this paper, we have proposed a new online Wavelet Complementary velocity Estimator (WCE) over position and acceleration data gathered from an electro hydraulic servo shaking table. This is a batch estimator type that is based on the wavelet filter banks which extract the high and low resolution of data. The proposed complementary estimator combines these two resolutions of velocities which acquired from numerical differentiation and integration of the position and acceleration sensors by considering a fixed moving horizon window as input to wavelet filter. Because of using wavelet filters, it can be implemented in a parallel procedure. By this method the numerical velocity is estimated without having high noise of differentiators, integration drifting bias and with less delay which is suitable for active vibration control in high precision Mechatronics systems by Direct Velocity Feedback (DVF) methods. This method allows us to make velocity sensors with less mechanically moving parts which makes it suitable for fast miniature structures. We have compared this method with Kalman and Butterworth filters over stability, delay and benchmarked them by their long time velocity integration for getting back the initial position data. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

On whistler-mode group velocity

International Nuclear Information System (INIS)

Sazhin, S.S.

1986-01-01

An analytical of the group velocity of whistler-mode waves propagating parallel to the magnetic field in a hot anisotropic plasma is presented. Some simple approximate formulae, which can be used for the magnetospheric applications, are derived. These formulae can predict some properties of this group velocity which were not previously recognized or were obtained by numerical methods. In particular, it is pointed out that the anisotropy tends to compensate for the influence of the electron temperature on the value of the group velocity when the wave frequency is well below the electron gyrofrequency. It is predicted, that under conditions at frequencies near the electron gyrofrequency, this velocity tends towards zero

AIRBORNE X-HH INCIDENCE ANGLE IMPACT ON CANOPY HEIGHT RETREIVAL: IMPLICATIONS FOR SPACEBORNE X-HH TANDEM-X GLOBAL CANOPY HEIGHT MODEL

Directory of Open Access Journals (Sweden)

M. L. Tighe

2012-07-01

Full Text Available To support international climate change mitigation efforts, the United Nations REDD+ initiative (Reducing Emissions from Deforestation and Degradation seeks to reduce land use induced greenhouse gas emissions to the atmosphere. It requires independent monitoring of forest cover and forest biomass information in a spatially explicit form. It is widely recognised that remote sensing is required to deliver this information. Synthetic Aperture Radar interferometry (InSAR techniques have gained traction in the last decade as a viable technology from which vegetation canopy height and bare earth elevations can be derived. The viewing geometry of a SAR sensor is side-looking where the radar pulse is transmitted out to one side of the aircraft or satellite, defining an incidence angle (θ range. The incidence angle will change from near-range (NR to far-range (FR across of the track of the SAR platform. InSAR uses image pairs and thus, contain two set of incidence angles. Changes in the InSAR incidence angles can alter the relative contributions from the vegetation canopy and the ground surface and thus, affect the retrieved vegetation canopy height. Incidence angle change is less pronounced in spaceborne data than in airborne data and mitigated somewhat when multiple InSAR-data takes are combined. This study uses NEXTMap® single- and multi-pass X-band HH polarized InSAR to derive vegetation canopy height from the scattering phase centre height (hspc. Comparisons with in situ vegetation canopy height over three test sites (Arizona-1, Minnesota-2; the effect of incidence angle changes across swath on the X-HH InSAR hspc was examined. Results indicate at steep incidence angles (θ = 35º, more exposure of lower vegetation canopy structure (e.g. tree trunks led to greater lower canopy double bounce, increased ground scattering, and decreased volume scattering. This resulted in a lower scattering phase centre height (hspc or a greater underestimation of

Heritability of adult body height

DEFF Research Database (Denmark)

Silventoinen, Karri; Sammalisto, Sampo; Perola, Markus

2003-01-01

/unique environment (AE) model. Among women the heritability estimates were generally lower than among men with greater variation between countries, ranging from 0.68 to 0.84 when an additive genes/shared environment/unique environment (ACE) model was used. In four populations where an AE model fit equally well...... countries; body height was least in Italy (177 cm in men and 163 cm in women) and greatest in the Netherlands (184 cm and 171 cm, respectively). In men there was no corresponding variation in heritability of body height, heritability estimates ranging from 0.87 to 0.93 in populations under an additive genes...... or better, heritability ranged from 0.89 to 0.93. This difference between the sexes was mainly due to the effect of the shared environmental component of variance, which appears to be more important among women than among men in our study populations. Our results indicate that, in general, there are only...

Ultrasonic device for real-time sewage velocity and suspended particles concentration measurements.

Science.gov (United States)

Abda, F; Azbaid, A; Ensminger, D; Fischer, S; François, P; Schmitt, P; Pallarès, A

2009-01-01

In the frame of a technological research and innovation network in water and environment technologies (RITEAU, Réseau de Recherche et d'Innovation Technologique Eau et Environnement), our research group, in collaboration with industrial partners and other research institutions, has been in charge of the development of a suitable flowmeter: an ultrasonic device measuring simultaneously the water flow and the concentration of size classes of suspended particles. Working on the pulsed ultrasound principle, our multi-frequency device (1 to 14 MHz) allows flow velocity and water height measurement and estimation of suspended solids concentration. Velocity measurements rely on the coherent Doppler principle. A self developed frequency estimator, so called Spectral Identification method, was used and compared to the classical Pulse-Pair method. Several measurements campaigns on one wastewater collector of the French city of Strasbourg gave very satisfactory results and showed smaller standard deviation values for the Doppler frequency extracted by the Spectral Identification method. A specific algorithm was also developed for the water height measurements. It relies on the water surface acoustic impedance rupture and its peak localisation and behaviour in the collected backscattering data. This algorithm was positively tested on long time measurements on the same wastewater collector. A large part of the article is devoted to the measurements of the suspended solids concentrations. Our data analysis consists in the adaptation of the well described acoustic behaviour of sand to the behaviour of wastewater particles. Both acoustic attenuation and acoustic backscattering data over multiple frequencies are analyzed for the extrapolation of size classes and respective concentrations. Under dry weather conditions, the massic backscattering coefficient and the overall size distribution showed similar evolution whatever the measurement site was and were suggesting a global

Clogging of granular material in vertical pipes discharged at constant velocity

Directory of Open Access Journals (Sweden)

López-Rodríguez Diego

2017-01-01

Full Text Available We report an experimental study on the flow of spherical particles through a vertical pipe discharged at constant velocity by means of a conveyor belt placed at the bottom. For a pipe diameter 3.67 times the diameter of the particles, we observe the development of hanging arches that stop the flow as they are able to support the weight of the particles above them. We find that the distribution of times that it takes until a stable clog develops, decays exponentially. This is compatible with a clogging probability that remains constant during the discharge. We also observe that the probability of clogging along the pipe decreases with the height, i.e. most of the clogs are developed near the bottom. This spatial dependence may be attributed to different pressure values within the pipe which might also be related to a spontaneous development of an helical structure of the grains inside the pipe.

Wall-attached structures of streamwise velocity fluctuations in turbulent boundary layer

Science.gov (United States)

Hwang, Jinyul; Sung, Hyung Jin

2017-11-01

The wall-attached structures of streamwise velocity fluctuations (u) are explored using direct numerical simulation data of turbulent boundary layer at Reτ = 1000 . We identify the structures of u, which are extended close to the wall. Their height (ly) ranges from the near-wall region to the edge of turbulent boundary layer. They are geometrically self-similar in a sense that the length and width of the structures are proportional to the distance from the wall. The population density of the attached structures shows that the tall attached structures (290 wall. The wall-attached structures of u identified in the present work are a proper candidate for Townsend's attached eddy hypothesis and these structures exist in the low Reynolds number turbulent boundary layer. This work was supported by the Creative Research Initiatives (No. 2017-013369) program of the National Research Foundation of Korea (MSIP) and supported by the Supercomputing Center (KISTI).

Characteristic wave velocities in spherical electromagnetic cloaks

International Nuclear Information System (INIS)

Yaghjian, A D; Maci, S; Martini, E

2009-01-01

We investigate the characteristic wave velocities in spherical electromagnetic cloaks, namely, phase, ray, group and energy-transport velocities. After deriving explicit expressions for the phase and ray velocities (the latter defined as the phase velocity along the direction of the Poynting vector), special attention is given to the determination of group and energy-transport velocities, because a cursory application of conventional formulae for local group and energy-transport velocities can lead to a discrepancy between these velocities if the permittivity and permeability dyadics are not equal over a frequency range about the center frequency. In contrast, a general theorem can be proven from Maxwell's equations that the local group and energy-transport velocities are equal in linear, lossless, frequency dispersive, source-free bianisotropic material. This apparent paradox is explained by showing that the local fields of the spherical cloak uncouple into an E wave and an H wave, each with its own group and energy-transport velocities, and that the group and energy-transport velocities of either the E wave or the H wave are equal and thus satisfy the general theorem.

Growth and Final Height Among Children With Phenylketonuria.

Science.gov (United States)

Thiele, Alena G; Gausche, Ruth; Lindenberg, Cornelia; Beger, Christoph; Arelin, Maria; Rohde, Carmen; Mütze, Ulrike; Weigel, Johannes F; Mohnike, Klaus; Baerwald, Christoph; Scholz, Markus; Kiess, Wieland; Pfäffle, Roland; Beblo, Skadi

2017-11-01

Growth is an important criterion to evaluate health in childhood and adolescence, especially in patients depending on special dietary treatment. Phenylketonuria (PKU) is the most common inherited disease of amino acid metabolism. Patients with PKU depend on a special phenylalanine-restricted diet, low in natural protein. The study aimed to evaluate growth, growth rate, and target height in 224 patients with PKU. Retrospective, longitudinal analysis of standardized, yearly measurements of height, weight, and calculated growth rate (SD score [SDS]) of patients with PKU aged 0 to 18 years were conducted by using the national computerized CrescNet database. Inclusion was restricted to patients carried to term with a confirmed diagnosis of PKU or mild hyperphenylalaninemia determined by newborn screening and early treatment initiation. From birth to adulthood, patients with PKU were significantly shorter than healthy German children (height SDS at 18 years: -0.882 ± 0.108, P < .001). They missed their target height by 3 cm by adulthood (women: P = .02) and 5 cm (men: P = .01). In patients receiving casein hydrolysate during childhood, this was more pronounced compared with patients receiving amino acid mixtures ( P < .001). Growth rate was significantly reduced during their first 2 years of life and in puberty (growth rate SDS: -1.1 to -0.5 m/year, P < .001 and -0.5; P < .02). Early diagnosed, treated, and continuously monitored patients with PKU showed reduced height from birth onward. During the last 2 decades, this phenomenon attenuated, probably because of advances in PKU therapy related to protein supplements and special low-protein foods. Copyright © 2017 by the American Academy of Pediatrics.

Effects of stand density on top height estimation for ponderosa pine

Science.gov (United States)

Martin Ritchie; Jianwei Zhang; Todd Hamilton

2012-01-01

Site index, estimated as a function of dominant-tree height and age, is often used as an expression of site quality. This expression is assumed to be effectively independent of stand density. Observation of dominant height at two different ponderosa pine levels-of-growing-stock studies revealed that top height stability with respect to stand density depends on the...

Global height datum unification: a new approach in gravity potential space

Science.gov (United States)

Ardalan, A. A.; Safari, A.

2005-12-01

The problem of “global height datum unification” is solved in the gravity potential space based on: (1) high-resolution local gravity field modeling, (2) geocentric coordinates of the reference benchmark, and (3) a known value of the geoid’s potential. The high-resolution local gravity field model is derived based on a solution of the fixed-free two-boundary-value problem of the Earth’s gravity field using (a) potential difference values (from precise leveling), (b) modulus of the gravity vector (from gravimetry), (c) astronomical longitude and latitude (from geodetic astronomy and/or combination of (GNSS) Global Navigation Satellite System observations with total station measurements), (d) and satellite altimetry. Knowing the height of the reference benchmark in the national height system and its geocentric GNSS coordinates, and using the derived high-resolution local gravity field model, the gravity potential value of the zero point of the height system is computed. The difference between the derived gravity potential value of the zero point of the height system and the geoid’s potential value is computed. This potential difference gives the offset of the zero point of the height system from geoid in the “potential space”, which is transferred into “geometry space” using the transformation formula derived in this paper. The method was applied to the computation of the offset of the zero point of the Iranian height datum from the geoid’s potential value W 0=62636855.8 m2/s2. According to the geometry space computations, the height datum of Iran is 0.09 m below the geoid.

FERDO/FERD, Unfolding of Pulse-Height Spectrometer Spectra

International Nuclear Information System (INIS)

Rust, B.W.; Ingersoll, D.T.; Burrus, W.R.

1985-01-01

1 - Description of problem or function: FERDO and FERD are unfolding codes which can be used to correct observed pulse-height distributions for the non-ideal response of a pulse-height spectrometer or to solve poorly conditioned linear equations. 2 - Method of solution: It is assumed that the response of the spectrometer is given by Ax = b, where A is the spectrometer response function matrix, x is the unknown spectrum, and b is the pulse-height distribution. FERDO does not resolve directly for x but instead solves for p = Wx, where W is a 'window function matrix'. Typically, W is the resolution function of an ideal spectrometer which has a single Gaussian response. The effective resolution of the unfolding solution may be varied by the choice of W. Confidence intervals are found for each element of the solution p

Southern high-velocity stars

International Nuclear Information System (INIS)

Augensen, H.J.; Buscombe, W.

1978-01-01

Using the model of the Galaxy presented by Eggen, Lynden-Bell and Sandage (1962), plane galactic orbits have been calculated for 800 southern high-velocity stars which possess parallax, proper motion, and radial velocity data. The stars with trigonometric parallaxes were selected from Buscombe and Morris (1958), supplemented by more recent spectroscopic data. Photometric parallaxes from infrared color indices were used for bright red giants studied by Eggen (1970), and for red dwarfs for which Rodgers and Eggen (1974) determined radial velocities. A color-color diagram based on published values of (U-B) and (B-V) for most of these stars is shown. (Auth.)

Modified Feynman ratchet with velocity-dependent fluctuations

Directory of Open Access Journals (Sweden)

Jack Denur

2004-03-01

Full Text Available Abstract: The randomness of Brownian motion at thermodynamic equilibrium can be spontaneously broken by velocity-dependence of fluctuations, i.e., by dependence of values or probability distributions of fluctuating properties on Brownian-motional velocity. Such randomness-breaking can spontaneously obtain via interaction between Brownian-motional Doppler effects --- which manifest the required velocity-dependence --- and system geometrical asymmetry. A non random walk is thereby spontaneously superposed on Brownian motion, resulting in a systematic net drift velocity despite thermodynamic equilibrium. The time evolution of this systematic net drift velocity --- and of velocity probability density, force, and power output --- is derived for a velocity-dependent modification of Feynman's ratchet. We show that said spontaneous randomness-breaking, and consequent systematic net drift velocity, imply: bias from the Maxwellian of the system's velocity probability density, the force that tends to accelerate it, and its power output. Maximization, especially of power output, is discussed. Uncompensated decreases in total entropy, challenging the second law of thermodynamics, are thereby implied.

Alignment of stress, mean wind, and vertical gradient of the velocity vector

DEFF Research Database (Denmark)

Berg, Jacob; Mann, Jakob; Patton, E.G.

2012-01-01

In many applications in the atmospheric surface layer the turbulent-viscosity hypothesis is applied, i.e. the stress vector can be described through the vertical gradient of velocity. In the atmospheric surface layer, where the Coriolis force and baroclinic effects are considered negligible......, this is supposedly a good approximation. High resolution large-eddy simulation (LES) data show that it is indeed the case. Through analysis of WindCube lidar measurements accompanied by sonic measurements we show that this is, on the other hand, rarely the case in the real atmosphere. This might indicate that large...... of atmospheric boundary layer modeling. The measurements are from the Danish wind turbine test sites at Høvsøre. With theWindCube lidar we are able to reach heights of 250 meters and hence capture the entire atmospheric surface layer both in terms of wind speed and the direction of the mean stress vector....

The association between height and birth order: evidence from 652 518 Swedish men

OpenAIRE

Myrskyla, Mikko; Silventoinen, Karri; Jelenkovic, Aline; Tynelius, Per; Rasmussen, Finn

2013-01-01

Background Birth order is associated with outcomes such as birth weight and adult socioeconomic position (SEP), but little is known about the association with adult height. This potential birth order-height association is important because height predicts health, and because the association may help explain population-level height trends. We studied the birth order-height association and whether it varies by family characteristics or birth cohort. Methods We used the Swedish Military Conscrip...

Trend in Height of Turkish and Moroccan Children Living in The Netherlands

Science.gov (United States)

Schönbeck, Yvonne; van Dommelen, Paula; HiraSing, Remy A.; van Buuren, Stef

2015-01-01

Objectives To study trends in height of Turkish and Moroccan immigrant children living in The Netherlands, to investigate the association between height and background characteristics in these children, and to calculate height-for-age-references data for these groups. Design Nationwide cross-sectional data collection from children aged 0 to 18 years by trained professionals in 1997 and 2009. The study population consisted of 2,822 Turkish 2,779 Moroccan, and 13,705 Dutch origin children in 1997and 2,548 Turkish, 2,594 Moroccan, and 11,255 Dutch origin children in 2009. Main outcome measures: Mean height in cm, and mean height standard deviation scores. Results In 2009, mean height at the age of 18y was similar for Turkish and Moroccan children: 177 cm for boys and 163 cm for girls, which was 2 to 3 cm taller than in 1997. Still, Turkish and Moroccan adolescents were 5.5 cm (boys) to 7 cm (girls) shorter than their Dutch peers. No significant differences were found in mean height standard deviation scores across the educational level of the parents, geographical region, primary language spoken at home, and immigrant generation. Conclusions While the secular height increase in Dutch children came to a halt, the trend in Turkish and Moroccan children living in The Netherlands continued. However, large differences in height between Turkish and Moroccan children and Dutch children remain. We found no association with the background characteristics. We recommend the use of the new growth charts for children of Turkish and Moroccan origin who have a height-for-age below -2SD on the growth chart for Dutch children. PMID:25938671

human pelvis height is associated with other pelvis measurements

African Journals Online (AJOL)

guyton2

no study seeking to relate pelvis height to the other pelvis measurements of obstetric importance in Ugandans. In this paper we set out to answer the research question what are the associations between the various pelvis anthropometric measurements of obstetric importance with pelvis height in a sample of bones from the ...

Velocity distribution of fragments of catastrophic impacts

Science.gov (United States)

Takagi, Yasuhiko; Kato, Manabu; Mizutani, Hitoshi

1992-01-01

Three dimensional velocities of fragments produced by laboratory impact experiments were measured for basalts and pyrophyllites. The velocity distribution of fragments obtained shows that the velocity range of the major fragments is rather narrow, at most within a factor of 3 and that no clear dependence of velocity on the fragment mass is observed. The NonDimensional Impact Stress (NDIS) defined by Mizutani et al. (1990) is found to be an appropriate scaling parameter to describe the overall fragment velocity as well as the antipodal velocity.

Serum osteoprotegerin levels are related to height loss: The Tromsø Study

International Nuclear Information System (INIS)

Jørgensen, Lone; Hansen, John-Bjarne; Brox, Jan; Mathiesen, Ellisiv; Vik, Anders; Jacobsen, Bjarne K.

2011-01-01

Severe loss of body height is often a consequence of osteoporotic vertebral fractures. Osteoprotegerin (OPG) and receptor activator of nuclear factor-kB ligand (RANKL) are cytokines essential for the regulation of bone resorption. The aim of this study was to assess the relationship between the OPG/RANKL system and height loss. A total of 4,435 inhabitants from the municipality of Tromsø, Norway (2,169 men and 2,266 women) were followed for 6 years. Baseline measurements included height, weight, bone mineral density, OPG, RANKL, serum parathyroid hormone and information about lifestyle, prevalent diseases and use of medication. Height was measured again at follow-up, and the loss of height was categorized into 4 groups: ≤1, 1.1–2, 2.1–3, >3 cm. We found increasing height loss with increasing baseline OPG levels in both men and women (P trend = 0.02 and 0.001, respectively), after adjustments for age and other confounders. However, when the women were stratified according to menopausal status and use of hormone replacement therapy (HRT), a significant relationship was present only among postmenopausal women not using HRT (P trend = 0.02). No relations between OPG and height loss were found in post-menopausal HRT-users and premenopausal women (P trend ≥0.39). We conclude that height loss is positively associated with OPG in men and in postmenopausal women not using HRT. No relationship was found between RANKL and height loss.

Looking Like a Leader–Facial Shape Predicts Perceived Height and Leadership Ability

Science.gov (United States)

Re, Daniel E.; Hunter, David W.; Coetzee, Vinet; Tiddeman, Bernard P.; Xiao, Dengke; DeBruine, Lisa M.; Jones, Benedict C.; Perrett, David I.

2013-01-01

Judgments of leadership ability from face images predict the outcomes of actual political elections and are correlated with leadership success in the corporate world. The specific facial cues that people use to judge leadership remain unclear, however. Physical height is also associated with political and organizational success, raising the possibility that facial cues of height contribute to leadership perceptions. Consequently, we assessed whether cues to height exist in the face and, if so, whether they are associated with perception of leadership ability. We found that facial cues to perceived height had a strong relationship with perceived leadership ability. Furthermore, when allowed to manually manipulate faces, participants increased facial cues associated with perceived height in order to maximize leadership perception. A morphometric analysis of face shape revealed that structural facial masculinity was not responsible for the relationship between perceived height and perceived leadership ability. Given the prominence of facial appearance in making social judgments, facial cues to perceived height may have a significant influence on leadership selection. PMID:24324651

Estimating Planetary Boundary Layer Heights from NOAA Profiler Network Wind Profiler Data

Science.gov (United States)

Molod, Andrea M.; Salmun, H.; Dempsey, M

2015-01-01

An algorithm was developed to estimate planetary boundary layer (PBL) heights from hourly archived wind profiler data from the NOAA Profiler Network (NPN) sites located throughout the central United States. Unlike previous studies, the present algorithm has been applied to a long record of publicly available wind profiler signal backscatter data. Under clear conditions, summertime averaged hourly time series of PBL heights compare well with Richardson-number based estimates at the few NPN stations with hourly temperature measurements. Comparisons with clear sky reanalysis based estimates show that the wind profiler PBL heights are lower by approximately 250-500 m. The geographical distribution of daily maximum PBL heights corresponds well with the expected distribution based on patterns of surface temperature and soil moisture. Wind profiler PBL heights were also estimated under mostly cloudy conditions, and are generally higher than both the Richardson number based and reanalysis PBL heights, resulting in a smaller clear-cloudy condition difference. The algorithm presented here was shown to provide a reliable summertime climatology of daytime hourly PBL heights throughout the central United States.

Automated lidar-derived canopy height estimates for the Upper Mississippi River System

Science.gov (United States)

Hlavacek, Enrika

2015-01-01

Land cover/land use (LCU) classifications serve as important decision support products for researchers and land managers. The LCU classifications produced by the U.S. Geological Survey’s Upper Midwest Environmental Sciences Center (UMESC) include canopy height estimates that are assigned through manual aerial photography interpretation techniques. In an effort to improve upon these techniques, this project investigated the use of high-density lidar data for the Upper Mississippi River System to determine canopy height. An ArcGIS tool was developed to automatically derive height modifier information based on the extent of land cover features for forest classes. The measurement of canopy height included a calculation of the average height from lidar point cloud data as well as the inclusion of a local maximum filter to identify individual tree canopies. Results were compared to original manually interpreted height modifiers and to field survey data from U.S. Forest Service Forest Inventory and Analysis plots. This project demonstrated the effectiveness of utilizing lidar data to more efficiently assign height modifier attributes to LCU classifications produced by the UMESC.

The influence of craniofacial to standing height proportion on perceived attractiveness.

Science.gov (United States)

Naini, F B; Cobourne, M T; McDonald, F; Donaldson, A N A

2008-10-01

An idealised male image, based on Vitruvian Man, was created. The craniofacial height was altered from a proportion of 1/6 to 1/10 of standing height, creating 10 images shown in random order to 89 observers (74 lay people; 15 clinicians), who ranked the images from the most to the least attractive. The main outcome was the preference ranks of image attractiveness given by the observers. Linear regressions were used to assess what influences the choice for the most and the least attractive images, followed by a multivariate rank ordinal logistic regression to test the influence of age, gender, ethnicity and professional status of the observer. A craniofacial height to standing height proportion of 1/7.5 was perceived as the most attractive (36%), followed by a proportion of 1/8 (26%). The images chosen as most attractive by more than 10% of observers had a mean proportion of 1/7.8(min=1/7; max=1/8.5). The images perceived as most unattractive had a proportion of 1/6 and 1/10. The choice of images was not influenced by the age, gender, ethnicity or professional status of the observers. The ideal craniofacial height to standing height proportion is in the range 1/7 to 1/8.5. This finding should be considered when planning treatment to alter craniofacial or facial height.

Arm-associated measurements as estimates of true height in black ...

African Journals Online (AJOL)

arm-associated measurements to true height included that of the World Health ... Conclusion: Findings indicate the need for gender and race-specific height estimation ..... New. York, NY: Springer; 2012. 12. Golshan M, Amra B, Hoghoghi MA.

Trend in height of Turkish and Moroccan children living in the Netherlands

NARCIS (Netherlands)

Schönbeck, Y.; Dommelen, P. van; Hirasing, R.A.; Buuren, S. van

2015-01-01

Objectives To study trends in height of Turkish and Moroccan immigrant children living in The Netherlands, to investigate the association between height and background characteristics in these children, and to calculate height-for-age-references data for these groups. Design Nationwide

Oxygen–induced barrier height changes in aluminium – amorphous ...

African Journals Online (AJOL)

The results show that the application of voltage causes charge exchange between the surface states and the semiconductor leading to a change in the height of the potential barrier for electrons passing from aluminium into the a-Se films. The empirically determined values of barrier height of Al/a-Se diodes with thin and ...

Stereoscopic, thermal, and true deep cumulus cloud top heights

Science.gov (United States)

Llewellyn-Jones, D. T.; Corlett, G. K.; Lawrence, S. P.; Remedios, J. J.; Sherwood, S. C.; Chae, J.; Minnis, P.; McGill, M.

2004-05-01

We compare cloud-top height estimates from several sensors: thermal tops from GOES-8 and MODIS, stereoscopic tops from MISR, and directly measured heights from the Goddard Cloud Physics Lidar on board the ER-2, all collected during the CRYSTAL-FACE field campaign. Comparisons reveal a persistent 1-2 km underestimation of cloud-top heights by thermal imagery, even when the finite optical extinctions near cloud top and in thin overlying cirrus are taken into account. The most severe underestimates occur for the tallest clouds. The MISR "best-sinds" and lidar estimates disagree in very similar ways with thermally estimated tops, which we take as evidence of excellent performance by MISR. Encouraged by this, we use MISR to examine variations in cloud penetration and thermal top height errors in several locations of tropical deep convection over multiple seasons. The goals of this are, first, to learn how cloud penetration depends on the near-tropopause environment; and second, to gain further insight into the mysterious underestimation of tops by thermal imagery.

Diagnostic test of predicted height model in Indonesian elderly: a study in an urban area

Directory of Open Access Journals (Sweden)

Fatmah Fatmah

2010-08-01

Full Text Available Aim In an anthropometric assessment, elderly are frequently unable to measure their height due to mobility and skeletal deformities. An alternative is to use a surrogate value of stature from arm span, knee height, and sitting height. The equations developed for predicting height in Indonesian elderly using these three predictors. The equations put in the nutritional assessment card (NSA of older people. Before the card which is the first new technology in Indonesia will be applied in the community, it should be tested. The study aimed was to conduct diagnostic test of predicted height model in the card compared to actual height.Methods Model validation towards 400 healthy elderly conducted in Jakarta City with cross-sectional design. The study was the second validation test of the model besides Depok City representing semi urban area which was undertaken as the first study.Result Male elderly had higher mean age, height, weight, arm span, knee height, and sitting height as compared to female elderly. The highest correlation between knee height and standing height was similar in women (r = 0.80; P < 0.001 and men (r = 0.78; P < 0.001, and followed by arm span and sitting height. Knee height had the lowest difference with standing height in men (3.13 cm and women (2.79 cm. Knee height had the biggest sensitivity (92.2%, and the highest specificity on sitting height (91.2%.Conclusion Stature prediction equation based on knee-height, arm span, and sitting height are applicable for nutritional status assessment in Indonesian elderly. (Med J Indones 2010;19:199-204Key words: diagnostic test, elderly, predicted height model

Comparative validation of the radiographic and tomographic measurement of patellar height

Directory of Open Access Journals (Sweden)

Marco Antonio Schueda

2013-09-01

Full Text Available OBJECTIVE: To evaluate and validate the radiographic measurement of patellar height with computerized tomography scans. METHODS: Measured the patellar height through the lateral radiographic image supported by one foot and sagittal tomographic view of the knee in extension, flexion of 20°, and quadriceps contraction of 40 patients (80 knees, asymptomatic and no history of knee injuries using Insall-Salvati index. There were 20 adult females and 20 adult males. RESULTS: The height patellar index was higher in women of all images taken, in proportion. There was no statistical difference of patellar height index between the radiographics and tomographics images. CONCLUSION: The Insall-Salvati index in females was higher in all cases evaluated. Furthermore, it is possible to measure the patellar height index during tomographic study without distorting the results obtained, using to define the presence of patella alta or patella baja.

Foot and Ankle Kinematics During Descent From Varying Step Heights.

Science.gov (United States)

Gerstle, Emily E; O'Connor, Kristian; Keenan, Kevin G; Cobb, Stephen C

2017-12-01

In the general population, one-third of incidences during step negotiation occur during the transition to level walking. Furthermore, falls during curb negotiation are a common cause of injury in older adults. Distal foot kinematics may be an important factor in determining injury risk associated with transition step negotiation. The purpose of this study was to identify foot and ankle kinematics of uninjured individuals during descent from varying step heights. A 7-segment foot model was used to quantify kinematics as participants walked on a level walkway, stepped down a single step (heights: 5 cm, 15 cm, 25 cm), and continued walking. As step height increased, landing strategy transitioned from the rearfoot to the forefoot, and the rearfoot, lateral and medial midfoot, and medial forefoot became more plantar flexed. During weight acceptance, sagittal plane range of motion of the rearfoot, lateral midfoot, and medial and lateral forefoot increased as step height increased. The changes in landing strategy and distal foot function suggest a less stable ankle position at initial contact and increased demand on the distal foot at initial contact and through the weight acceptance phase of transition step negotiation as step height increases.

Velocity spectrum for the Iranian plateau

Science.gov (United States)

Bastami, Morteza; Soghrat, M. R.

2018-01-01

Peak ground acceleration (PGA) and spectral acceleration values have been proposed in most building codes/guidelines, unlike spectral velocity (SV) and peak ground velocity (PGV). Recent studies have demonstrated the importance of spectral velocity and peak ground velocity in the design of long period structures (e.g., pipelines, tunnels, tanks, and high-rise buildings) and evaluation of seismic vulnerability in underground structures. The current study was undertaken to develop a velocity spectrum and for estimation of PGV. In order to determine these parameters, 398 three-component accelerograms recorded by the Building and Housing Research Center (BHRC) were used. The moment magnitude (Mw) in the selected database was 4.1 to 7.3, and the events occurred after 1977. In the database, the average shear-wave velocity at 0 to 30 m in depth (Vs30) was available for only 217 records; thus, the site class for the remaining was estimated using empirical methods. Because of the importance of the velocity spectrum at low frequencies, the signal-to-noise ratio of 2 was chosen for determination of the low and high frequency to include a wider range of frequency content. This value can produce conservative results. After estimation of the shape of the velocity design spectrum, the PGV was also estimated for the region under study by finding the correlation between PGV and spectral acceleration at the period of 1 s.

Can height categories replace weight categories in striking martial arts competitions? A pilot study.

Science.gov (United States)

Dubnov-Raz, Gal; Mashiach-Arazi, Yael; Nouriel, Ariella; Raz, Raanan; Constantini, Naama W

2015-09-29

In most combat sports and martial arts, athletes compete within weight categories. Disordered eating behaviors and intentional pre-competition rapid weight loss are commonly seen in this population, attributed to weight categorization. We examined if height categories can be used as an alternative to weight categories for competition, in order to protect the health of athletes. Height and weight of 169 child and adolescent competitive karate athletes were measured. Participants were divided into eleven hypothetical weight categories of 5 kg increments, and eleven hypothetical height categories of 5 cm increments. We calculated the coefficient of variation of height and weight by each division method. We also calculated how many participants fit into corresponding categories of both height and weight, and how many would shift a category if divided by height. There was a high correlation between height and weight (r = 0.91, p<0.001). The mean range of heights seen within current weight categories was reduced by 83% when participants were divided by height. When allocating athletes by height categories, 74% of athletes would shift up or down one weight category at most, compared with the current categorization method. We conclude that dividing young karate athletes by height categories significantly reduced the range of heights of competitors within the category. Such categorization would not cause athletes to compete against much heavier opponents in most cases. Using height categories as a means to reduce eating disorders in combat sports should be further examined.

Estimation of Height from Arm Span in 6-11 Years Children in Odisha, India

Directory of Open Access Journals (Sweden)

Snigdha Prava Mishra

2017-10-01

Full Text Available Introduction: Standing height is an important anthropometric parameter to track longitudinal growth, to estimate body fatness and to calculate energy requirement. Measurement of height may be difficult in children who cannot stand. Aim: To establish regression equation for estimation of height from arm span in children. To check comparative relevancy of this equation with fixed height-to-arm span ratio (HAR for estimation of height. Materials and Methods: A cross-sectional study was conducted with 6-11 years school children (n=1465, Boys=774, Girls=691 in state of Odisha, India. Height was measured by portable stadiometer and arm span was measured by fiberglass measuring tape to nearest 0.1 cm. Pearson correlation and regression analysis was carried out between height and arm span data. p<0.05 (two tail was considered statistically significant. Results: Mean height and arm span in boys (124.16±8.74 cm and 125.57±10.43 cm respectively was significantly more (p<0.001 than height and arm span in girls (121.18±10.37 cm and 121.50±11.68 cm respectively. Mean HAR was 0.9942±0.0279. Correlation between height and arm span in boys was r = 0.94 (p<0.001 and in girls was r = 0.96 (p<0.001. Overall correlation coefficient was r = 0.95 (p<0.001. Regression equation for estimation of height from arm span was established: Height (cm = 0.8192 * arm span (cm + 21.46. Conclusion: Height in children of 6-11 years showed strong positive correlation with arm span. Regression equation established from this study can be used to estimate height from arm span. This estimation is more reliable than estimation of height from HAR.

An attempt to link the Brazilian Height System to a World Height System

Directory of Open Access Journals (Sweden)

V. G. Ferreira

Full Text Available This paper deals with the geopotential approach to investigate the present Brazilian Height System (BHS. Geopotential numbers are derived from Global Positioning System (GPS satellite surveying and disturbing potential on selected benchmarks. A model for the disturbing potential can be obtained by an existing set of spherical harmonic coefficients such as the Earth Gravity Model 2008 (EGM08. The approach provides absolute evaluation of local normal geopotential numbers (aka spheropotential numbers related to a so-called World Height System (WHS. To test the validity of the proposed methodology, a numerical experiment was carried out related to a test region in Southern Brazil. The accuracy of the derived geopotential numbers was tested versus local normal geopotential numbers based on 262 GPS/leveling points. The root mean square error (RMSE value for metric offset of BHS derived from geopotential numbers and the disturbing potential modeling in the test area was estimated to be near 0.224 meters in the absolute view. Therefore, since these spheropotential numbers are referred to a local datum, these results of comparisons may be an indicator of the mean bias of local network due to the effect of local Sea Surface Topography (SSTop and possible offset between the unknown reference for the BHS and the quasigeoid model in the region.

Maximal intended velocity training induces greater gains in bench press performance than deliberately slower half-velocity training.

Science.gov (United States)

González-Badillo, Juan José; Rodríguez-Rosell, David; Sánchez-Medina, Luis; Gorostiaga, Esteban M; Pareja-Blanco, Fernando

2014-01-01

The purpose of this study was to compare the effect on strength gains of two isoinertial resistance training (RT) programmes that only differed in actual concentric velocity: maximal (MaxV) vs. half-maximal (HalfV) velocity. Twenty participants were assigned to a MaxV (n = 9) or HalfV (n = 11) group and trained 3 times per week during 6 weeks using the bench press (BP). Repetition velocity was controlled using a linear velocity transducer. A complementary study (n = 10) aimed to analyse whether the acute metabolic (blood lactate and ammonia) and mechanical response (velocity loss) was different between the MaxV and HalfV protocols used. Both groups improved strength performance from pre- to post-training, but MaxV resulted in significantly greater gains than HalfV in all variables analysed: one-repetition maximum (1RM) strength (18.2 vs. 9.7%), velocity developed against all (20.8 vs. 10.0%), light (11.5 vs. 4.5%) and heavy (36.2 vs. 17.3%) loads common to pre- and post-tests. Light and heavy loads were identified with those moved faster or slower than 0.80 m · s(-1) (∼ 60% 1RM in BP). Lactate tended to be significantly higher for MaxV vs. HalfV, with no differences observed for ammonia which was within resting values. Both groups obtained the greatest improvements at the training velocities (≤ 0.80 m · s(-1)). Movement velocity can be considered a fundamental component of RT intensity, since, for a given %1RM, the velocity at which loads are lifted largely determines the resulting training effect. BP strength gains can be maximised when repetitions are performed at maximal intended velocity.

Accelerated radial Fourier-velocity encoding using compressed sensing

Energy Technology Data Exchange (ETDEWEB)

Hilbert, Fabian; Han, Dietbert [Wuerzburg Univ. (Germany). Inst. of Radiology; Wech, Tobias; Koestler, Herbert [Wuerzburg Univ. (Germany). Inst. of Radiology; Wuerzburg Univ. (Germany). Comprehensive Heart Failure Center (CHFC)

2014-10-01

Purpose:Phase Contrast Magnetic Resonance Imaging (MRI) is a tool for non-invasive determination of flow velocities inside blood vessels. Because Phase Contrast MRI only measures a single mean velocity per voxel, it is only applicable to vessels significantly larger than the voxel size. In contrast, Fourier Velocity Encoding measures the entire velocity distribution inside a voxel, but requires a much longer acquisition time. For accurate diagnosis of stenosis in vessels on the scale of spatial resolution, it is important to know the velocity distribution of a voxel. Our aim was to determine velocity distributions with accelerated Fourier Velocity Encoding in an acquisition time required for a conventional Phase Contrast image. Materials and Methods:We imaged the femoral artery of healthy volunteers with ECG - triggered, radial CINE acquisition. Data acquisition was accelerated by undersampling, while missing data were reconstructed by Compressed Sensing. Velocity spectra of the vessel were evaluated by high resolution Phase Contrast images and compared to spectra from fully sampled and undersampled Fourier Velocity Encoding. By means of undersampling, it was possible to reduce the scan time for Fourier Velocity Encoding to the duration required for a conventional Phase Contrast image. Results:Acquisition time for a fully sampled data set with 12 different Velocity Encodings was 40 min. By applying a 12.6 - fold retrospective undersampling, a data set was generated equal to 3:10 min acquisition time, which is similar to a conventional Phase Contrast measurement. Velocity spectra from fully sampled and undersampled Fourier Velocity Encoded images are in good agreement and show the same maximum velocities as compared to velocity maps from Phase Contrast measurements. Conclusion: Compressed Sensing proved to reliably reconstruct Fourier Velocity Encoded data. Our results indicate that Fourier Velocity Encoding allows an accurate determination of the velocity

Accelerated radial Fourier-velocity encoding using compressed sensing

International Nuclear Information System (INIS)

Hilbert, Fabian; Han, Dietbert

2014-01-01

Purpose:Phase Contrast Magnetic Resonance Imaging (MRI) is a tool for non-invasive determination of flow velocities inside blood vessels. Because Phase Contrast MRI only measures a single mean velocity per voxel, it is only applicable to vessels significantly larger than the voxel size. In contrast, Fourier Velocity Encoding measures the entire velocity distribution inside a voxel, but requires a much longer acquisition time. For accurate diagnosis of stenosis in vessels on the scale of spatial resolution, it is important to know the velocity distribution of a voxel. Our aim was to determine velocity distributions with accelerated Fourier Velocity Encoding in an acquisition time required for a conventional Phase Contrast image. Materials and Methods:We imaged the femoral artery of healthy volunteers with ECG - triggered, radial CINE acquisition. Data acquisition was accelerated by undersampling, while missing data were reconstructed by Compressed Sensing. Velocity spectra of the vessel were evaluated by high resolution Phase Contrast images and compared to spectra from fully sampled and undersampled Fourier Velocity Encoding. By means of undersampling, it was possible to reduce the scan time for Fourier Velocity Encoding to the duration required for a conventional Phase Contrast image. Results:Acquisition time for a fully sampled data set with 12 different Velocity Encodings was 40 min. By applying a 12.6 - fold retrospective undersampling, a data set was generated equal to 3:10 min acquisition time, which is similar to a conventional Phase Contrast measurement. Velocity spectra from fully sampled and undersampled Fourier Velocity Encoded images are in good agreement and show the same maximum velocities as compared to velocity maps from Phase Contrast measurements. Conclusion: Compressed Sensing proved to reliably reconstruct Fourier Velocity Encoded data. Our results indicate that Fourier Velocity Encoding allows an accurate determination of the velocity

Accelerated radial Fourier-velocity encoding using compressed sensing.

Science.gov (United States)

Hilbert, Fabian; Wech, Tobias; Hahn, Dietbert; Köstler, Herbert

2014-09-01

Phase Contrast Magnetic Resonance Imaging (MRI) is a tool for non-invasive determination of flow velocities inside blood vessels. Because Phase Contrast MRI only measures a single mean velocity per voxel, it is only applicable to vessels significantly larger than the voxel size. In contrast, Fourier Velocity Encoding measures the entire velocity distribution inside a voxel, but requires a much longer acquisition time. For accurate diagnosis of stenosis in vessels on the scale of spatial resolution, it is important to know the velocity distribution of a voxel. Our aim was to determine velocity distributions with accelerated Fourier Velocity Encoding in an acquisition time required for a conventional Phase Contrast image. We imaged the femoral artery of healthy volunteers with ECG-triggered, radial CINE acquisition. Data acquisition was accelerated by undersampling, while missing data were reconstructed by Compressed Sensing. Velocity spectra of the vessel were evaluated by high resolution Phase Contrast images and compared to spectra from fully sampled and undersampled Fourier Velocity Encoding. By means of undersampling, it was possible to reduce the scan time for Fourier Velocity Encoding to the duration required for a conventional Phase Contrast image. Acquisition time for a fully sampled data set with 12 different Velocity Encodings was 40 min. By applying a 12.6-fold retrospective undersampling, a data set was generated equal to 3:10 min acquisition time, which is similar to a conventional Phase Contrast measurement. Velocity spectra from fully sampled and undersampled Fourier Velocity Encoded images are in good agreement and show the same maximum velocities as compared to velocity maps from Phase Contrast measurements. Compressed Sensing proved to reliably reconstruct Fourier Velocity Encoded data. Our results indicate that Fourier Velocity Encoding allows an accurate determination of the velocity distribution in vessels in the order of the voxel size. Thus

The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

Directory of Open Access Journals (Sweden)

Jaime Gomez-Gil

2014-10-01

Full Text Available Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations.

The Effect of Adolescent Experience on Labor Market Outcomes: The Case of Height.

Science.gov (United States)

Persico, Nicola; Postlewaite, Andrew; Silverman, Dan

2004-01-01

Taller workers receive a wage premium. Net of differences in family background, the disparity is similar in magnitude to the race and gender gaps. We exploit variation in an individual's height over time to explore how height affects wages. Controlling for teen height essentially eliminates the effect of adult height on wages for white men. The…

Questions Students Ask: About Terminal Velocity.

Science.gov (United States)

Meyer, Earl R.; Nelson, Jim

1984-01-01

If a ball were given an initial velocity in excess of its terminal velocity, would the upward force of air resistance (a function of velocity) be greater than the downward force of gravity and thus push the ball back upwards? An answer to this question is provided. (JN)

The radial velocity, velocity dispersion, and mass-to-light ratio of the Sculptor dwarf galaxy

Science.gov (United States)

Armandroff, T. E.; Da Costa, G. S.

1986-01-01

The radial velocity, velocity dispersion, and mass-to-light ratio for 16 K giants in the Sculptor dwarf galaxy are calculated. Spectra at the Ca II triplet are analyzed using cross-correlation techniques in order to obtain the mean velocity of + 107.4 + or - 2.0 km/s. The dimensional velocity dispersion estimated as 6.3 (+1.1, -1.3) km/s is combined with the calculated core radius and observed central surface brightness to produce a mass-to-light ratio of 6.0 in solar units. It is noted that the data indicate that the Sculptor contains a large amount of mass not found in globular clusters, and the mass is either in the form of remnant stars or low-mass dwarfs.

Inhomogeneity in barrier height at graphene/Si (GaAs) Schottky junctions.

Science.gov (United States)

Tomer, D; Rajput, S; Hudy, L J; Li, C H; Li, L

2015-05-29

Graphene (Gr) interfaced with a semiconductor forms a Schottky junction with rectifying properties, however, fluctuations in the Schottky barrier height are often observed. In this work, Schottky junctions are fabricated by transferring chemical vapor deposited monolayer Gr onto n-type Si and GaAs substrates. Temperature dependence of the barrier height and ideality factor are obtained by current-voltage measurements between 215 and 350 K. An increase in the zero bias barrier height and decrease in the ideality factor are observed with increasing temperature for both junctions. Such behavior is attributed to barrier inhomogeneities that arise from interfacial disorders as revealed by scanning tunneling microscopy/spectroscopy. Assuming a Gaussian distribution of the barrier heights, mean values of 1.14 ± 0.14 eV and 0.76 ± 0.10 eV are found for Gr/Si and Gr/GaAs junctions, respectively. These findings resolve the origin of barrier height inhomogeneities in these Schottky junctions.

Inhomogeneity in barrier height at graphene/Si (GaAs) Schottky junctions

International Nuclear Information System (INIS)

Tomer, D; Rajput, S; Hudy, L J; Li, L; Li, C H

2015-01-01

Graphene (Gr) interfaced with a semiconductor forms a Schottky junction with rectifying properties, however, fluctuations in the Schottky barrier height are often observed. In this work, Schottky junctions are fabricated by transferring chemical vapor deposited monolayer Gr onto n-type Si and GaAs substrates. Temperature dependence of the barrier height and ideality factor are obtained by current–voltage measurements between 215 and 350 K. An increase in the zero bias barrier height and decrease in the ideality factor are observed with increasing temperature for both junctions. Such behavior is attributed to barrier inhomogeneities that arise from interfacial disorders as revealed by scanning tunneling microscopy/spectroscopy. Assuming a Gaussian distribution of the barrier heights, mean values of 1.14 ± 0.14 eV and 0.76 ± 0.10 eV are found for Gr/Si and Gr/GaAs junctions, respectively. These findings resolve the origin of barrier height inhomogeneities in these Schottky junctions. (paper)

Does Height to Width Ratio Correlate with Mean Volume in Gastropods?

Science.gov (United States)

Barriga, R.; Seixas, G.; Payne, J.

2012-12-01

Marine organisms' shell shape and size show important biological information. For example, shape and size can dictate how the organism ranges for food and escapes predation. Due to lack of data and analysis, the evolution of shell size in marine gastropods (snails) remains poorly known. In this study, I attempt to find the relationship between height to width ratio and mean volume. I collected height and width measurements from primary literature sources and calculated volume from these measurements. My results indicate that there was no correlation between height to width ratio and mean volume between 500 to 200 Ma, but there was a correlation between 200 Ma to present where there is a steady increase in both height to width ratio and mean volume. This means that shell shape was not an important factor at the beginning of gastropod evolution but after 200 Ma body size evolution was increasingly driven by the height to width ratio.

Study the velocity and pressure exerted in front of the filter surface in the kitchen hood system by using ANSYS

Science.gov (United States)

Asmuin, Norzelawati; Pairan, M. Rasidi; Isa, Norasikin Mat; Sies, Farid

2017-04-01

Commercial kitchen hood ventilation system is a device used to capture and filtered the plumes from cooking activities in the kitchen area. Nowadays, it is very popular in the industrial sector such as restaurant and hotel to provide hygiene food. This study focused at the KSA filter part which installed in the kitchen hood system, the purpose of this study is to identify the critical region which indicated by observing the velocity and pressure of plumes exerted at of KSA filter. It is important to know the critical location of the KSA filter in order to install the nozzle which will helps increase the filtration effectiveness. The ANSYS 16.1 (FLUENT) software as a tool used to simulate the kitchen hood systems which consist of KSA filter. The commercial kitchen hood system model has a dimension 700 mm width, 1600 mm length and 555 mm height. The system has two inlets and one outlet. The velocity of the plumes is set to be 0.235m/s and the velocity of the inlet capture jet is set to be 1.078m/s. The KSA filter is placed 45 degree from the y axis. The result shows the plumes has more tendency flowing pass through at the bottom part of KSA filter.

Physiological Responses During the Time Limit at 100% of the Peak Velocity in the Carminatti’s Test in Futsal Players

Directory of Open Access Journals (Sweden)

Floriano Leandro Teixeira

2016-12-01

Full Text Available The aim of this study was to investigate the physiological responses during the time limit at the intensity of the peak velocity of the Carminatti’s test (T-CAR. Ten professional futsal players (age, 27.4 ± 5.8 years, body mass, 78.8 ± 8.5 kg, body height, 175.8 ± 6.8 cm, body fat mass, 14.1 ± 2.6% took part in the study. The players performed three tests, with an interval of at least 48 hours, as follows: the T-CAR to determine the peak velocity and the maximal heart rate; an incremental treadmill protocol to determine the maximal physiological responses; and a time limit running test at the peak velocity reached in the T-CAR. During the last two tests, a portable gas analyzer was used for direct measurement of cardiorespiratory variables. It was shown that the peak velocity was not significantly different from the maximal aerobic speed achieved in the laboratory (p = 0.213. All athletes reached their maximum oxygen uptake during the time limit test. The maximum oxygen uptake achieved during the time limit test was not different from that observed in the laboratory condition (51.1 ± 4.7 vs. 49.6 ± 4.7 ml·kg-1·min-1, respectively, p = 0.100. In addition, Bland and Altman plots evidenced acceptable agreement between them. On average, athletes took ~140 s to achieve maximum oxygen uptake and maintained it for ~180 s. Therefore, the peak velocity intensity can be used as an indicator of maximal aerobic power of futsal athletes and the time limit can be used as a reference for training prescription.

Microphysical Modeling of Mineral Clouds in GJ1214 b and GJ436 b: Predicting Upper Limits on the Cloud-top Height

Science.gov (United States)

Ohno, Kazumasa; Okuzumi, Satoshi

2018-05-01

The ubiquity of clouds in the atmospheres of exoplanets, especially of super-Earths, is one of the outstanding issues for the transmission spectra survey. Understanding the formation process of clouds in super-Earths is necessary to interpret the observed spectra correctly. In this study, we investigate the vertical distributions of particle size and mass density of mineral clouds in super-Earths using a microphysical model that takes into account the vertical transport and growth of cloud particles in a self-consistent manner. We demonstrate that the vertical profiles of mineral clouds significantly vary with the concentration of cloud condensation nuclei and atmospheric metallicity. We find that the height of the cloud top increases with increasing metallicity as long as the metallicity is lower than the threshold. If the metallicity is larger than the threshold, the cloud-top height no longer increases appreciably with metallicity because coalescence yields larger particles of higher settling velocities. We apply our cloud model to GJ1214 b and GJ436 b, for which recent transmission observations suggest the presence of high-altitude opaque clouds. For GJ436 b, we show that KCl particles can ascend high enough to explain the observation. For GJ1214 b, by contrast, the height of KCl clouds predicted from our model is too low to explain its flat transmission spectrum. Clouds made of highly porous KCl particles could explain the observations if the atmosphere is highly metal-rich, and hence the particle microstructure might be a key to interpret the flat spectrum of GJ1214 b.

Effect of cutting height and frequency on Leucaena leucocephala ...

African Journals Online (AJOL)

Leucaena leucocephala is a fast-growing tree that can provide both high quality forage and firewood. The objective of this trial was to determine the optimum height and frequency of cutting for both wood and forage production. Cutting heights at 0.3m, 0.6m and 1.0 m were superimposed on 3-month and 6-month cutting ...

Application of Vectors to Relative Velocity

Science.gov (United States)

Tin-Lam, Toh

2004-01-01

The topic 'relative velocity' has recently been introduced into the Cambridge Ordinary Level Additional Mathematics syllabus under the application of Vectors. In this note, the results of relative velocity and the 'reduction to rest' technique of teaching relative velocity are derived mathematically from vector algebra, in the hope of providing…

Computing discharge using the index velocity method

Science.gov (United States)

Levesque, Victor A.; Oberg, Kevin A.

2012-01-01

Application of the index velocity method for computing continuous records of discharge has become increasingly common, especially since the introduction of low-cost acoustic Doppler velocity meters (ADVMs) in 1997. Presently (2011), the index velocity method is being used to compute discharge records for approximately 470 gaging stations operated and maintained by the U.S. Geological Survey. The purpose of this report is to document and describe techniques for computing discharge records using the index velocity method. Computing discharge using the index velocity method differs from the traditional stage-discharge method by separating velocity and area into two ratings—the index velocity rating and the stage-area rating. The outputs from each of these ratings, mean channel velocity (V) and cross-sectional area (A), are then multiplied together to compute a discharge. For the index velocity method, V is a function of such parameters as streamwise velocity, stage, cross-stream velocity, and velocity head, and A is a function of stage and cross-section shape. The index velocity method can be used at locations where stage-discharge methods are used, but it is especially appropriate when more than one specific discharge can be measured for a specific stage. After the ADVM is selected, installed, and configured, the stage-area rating and the index velocity rating must be developed. A standard cross section is identified and surveyed in order to develop the stage-area rating. The standard cross section should be surveyed every year for the first 3 years of operation and thereafter at a lesser frequency, depending on the susceptibility of the cross section to change. Periodic measurements of discharge are used to calibrate and validate the index rating for the range of conditions experienced at the gaging station. Data from discharge measurements, ADVMs, and stage sensors are compiled for index-rating analysis. Index ratings are developed by means of regression

U.S. Geoid Heights (GEOID96)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for the conterminous United States is the GEOID96 model. The computation used about 1.8 million terrestrial and marine gravity data held in...

PR/VI Geoid Heights (GEOID96)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for Puerto Rico and the Virgin Islands is distributed as a GEOID96 model. The computation used 26,000 terrestrial and marine gravity data...

Sport-Specific Training Targeting the Proximal Segments and Throwing Velocity in Collegiate Throwing Athletes

Science.gov (United States)

Palmer, Thomas; Uhl, Timothy L.; Howell, Dana; Hewett, Timothy E.; Viele, Kert; Mattacola, Carl G.

2015-01-01

Context The ability to generate, absorb, and transmit forces through the proximal segments of the pelvis, spine, and trunk has been proposed to influence sport performance, yet traditional training techniques targeting the proximal segments have had limited success improving sport-specific performance. Objective To investigate the effects of a traditional endurance-training program and a sport-specific power-training program targeting the muscles that support the proximal segments and throwing velocity. Design Randomized controlled clinical trial. Setting University research laboratory and gymnasium. Patients or Other Participants A total of 46 (age = 20 ± 1.3 years, height = 175.7 ± 8.7 cm) healthy National Collegiate Athletic Association Division III female softball (n = 17) and male baseball (n = 29) players. Intervention(s) Blocked stratification for sex and position was used to randomly assign participants to 1 of 2 training groups for 7 weeks: a traditional endurance-training group (ET group; n = 21) or a power-stability–training group (PS group; n = 25). Mean Outcome Measure(s) The change score in peak throwing velocity (km/h) normalized for body weight (BW; kilograms) and change score in tests that challenge the muscles of the proximal segments normalized for BW (kilograms). We used 2-tailed independent-samples t tests to compare differences between the change scores. Results The peak throwing velocity (ET group = 0.01 ± 0.1 km/h/kg of BW, PS group = 0.08 ± 0.03 km/h/kg of BW; P < .001) and muscle power outputs for the chop (ET group = 0.22 ± 0.91 W/kg of BW, PS group = 1.3 ± 0.91 W/kg of BW; P < .001) and lift (ET group = 0.59 ± 0.67 W/kg of BW, PS group = 1.4 ± 0.87 W/kg of BW; P < .001) tests were higher at postintervention in the PT than in the ET group. Conclusions An improvement in throwing velocity occurred simultaneously with measures of muscular endurance and power after a sport-specific training regimen targeting the proximal segments

Demonstration of a Vector Velocity Technique

DEFF Research Database (Denmark)

Hansen, Peter Møller; Pedersen, Mads M.; Hansen, Kristoffer L.

2011-01-01

With conventional Doppler ultrasound it is not possible to estimate direction and velocity of blood flow, when the angle of insonation exceeds 60–70°. Transverse oscillation is an angle independent vector velocity technique which is now implemented on a conventional ultrasound scanner. In this pa......With conventional Doppler ultrasound it is not possible to estimate direction and velocity of blood flow, when the angle of insonation exceeds 60–70°. Transverse oscillation is an angle independent vector velocity technique which is now implemented on a conventional ultrasound scanner...

Bringing satellite winds to hub-height

DEFF Research Database (Denmark)

Badger, Merete; Pena Diaz, Alfredo; Bredesen, Rolv Erlend

2012-01-01

Satellite observations of the ocean surface can provide detailed information about the spatial wind variability over large areas. This is very valuable for the mapping of wind resources offshore where other measurements are costly and sparse. Satellite sensors operating at microwave frequencies...... measure the amount of radar backscatter from the sea surface, which is a function of the instant wind speed, wind direction, and satellite viewing geometry. A major limitation related to wind retrievals from satellite observations is that existing empirical model functions relate the radar backscatter...... to wind speed at the height 10 m only. The extrapolation of satellite wind fields to higher heights, which are more relevant for wind energy, remains a challenge which cannot be addressed by means of satellite data alone. As part of the EU-NORSEWInD project (2008-12), a hybrid method has been developed...

Validation of a CFD model by using 3D sonic anemometers to analyse the air velocity generated by an air-assisted sprayer equipped with two axial fans.

Science.gov (United States)

García-Ramos, F Javier; Malón, Hugo; Aguirre, A Javier; Boné, Antonio; Puyuelo, Javier; Vidal, Mariano

2015-01-22

A computational fluid dynamics (CFD) model of the air flow generated by an air-assisted sprayer equipped with two axial fans was developed and validated by practical experiments in the laboratory. The CFD model was developed by considering the total air flow supplied by the sprayer fan to be the main parameter, rather than the outlet air velocity. The model was developed for three air flows corresponding to three fan blade settings and assuming that the sprayer is stationary. Actual measurements of the air velocity near the sprayer were taken using 3D sonic anemometers. The workspace sprayer was divided into three sections, and the air velocity was measured in each section on both sides of the machine at a horizontal distance of 1.5, 2.5, and 3.5 m from the machine, and at heights of 1, 2, 3, and 4 m above the ground The coefficient of determination (R2) between the simulated and measured values was 0.859, which demonstrates a good correlation between the simulated and measured data. Considering the overall data, the air velocity values produced by the CFD model were not significantly different from the measured values.

Investigation of temperature dependent barrier height of Au/ZnO/Si schottky diodes

International Nuclear Information System (INIS)

Asghar, M.; Mahmood, K.; Rabia, S.; BM, S.; Shahid, M. Y.; Hasan, M. A.

2013-01-01

In this study, temperature dependent current-voltage (I-V) measurements have been performed to investigate the inhomogeneity in the temperature dependent barrier heights of Au/ZnO/Si Schottky barrier diode in the temperature range 150 - 400K. The room temperature values for ideality factor and barrier height were found to be 2.9 and 0.60 eV respectively indicating the inhomogenity in the barrier heights of grown samples. The Richardson plot and ideality factor verses barrier height graph were also drawn to verified the discontinuity between Au and ZnO. This barrier height inhomogenity was explained by applying Gaussian distribution model. The extrapolation of the linear Fap (n) plot to n= 1 has given a homogeneous barrier height of approximately 1.1 eV. Fap versus 1/T plot was drawn to obtain the values of mean barrier height for Au/ZnO/Si Schottky diode (1.1 eV) and standard deviation(ds) (0.02 V) at zero bais. (author)

Investigation of temperature dependent barrier height of Au/ZnO/Si schottky diodes

International Nuclear Information System (INIS)

Asghar, M; Mahmood, K; Rabia, S; M, Samaa B; Shahid, M Y; Hasan, M A

2014-01-01

In this study, temperature dependent current-voltage (I-V) measurements have been performed to investigate the inhomogeneity in the temperature dependent barrier heights of Au/ZnO/Si Schottky barrier diode in the temperature range 150 – 400K. The room temperature values for ideality factor and barrier height were found to be 2.9 and 0.60 eV respectively indicating the inhomogenity in the barrier heights of grown samples. The Richardson plot and ideality factor verses barrier height graph were also drawn to verified the discontinuity between Au and ZnO. This barrier height inhomogenity was explained by applying Gaussian distribution model. The extrapolation of the linear Φ ap (n) plot to n= 1 has given a homogeneous barrier height of approximately 1.1 eV. Φ ap versus 1/T plot was drawn to obtain the values of mean barrier height for Au/ZnO/Si Schottky diode (1.1 eV) and standard deviation(δ s ) (0.02 V) at zero bais

An investigation of cloud base height in Chiang Mai

Science.gov (United States)

Peengam, S.; Tohsing, K.

2017-09-01

Clouds play very important role in the variation of surface solar radiation and rain formation. To understand this role, it is necessary to know the physical and geometrical of properties of cloud. However, clouds vary with location and time, which lead to a difficulty to obtain their properties. In this work, a ceilometer was installed at a station of the Royal Rainmaking and Agricultural Aviation Department in Chiang Mai (17.80° N, 98.43° E) in order to measure cloud base height. The cloud base height data from this instrument were compared with those obtained from LiDAR, a more sophisticated instrument installed at the same site. It was found that the cloud base height from both instruments was in reasonable agreement, with root mean square difference (RMSD) and mean bias difference (MBD) of 19.21% and 1.58%, respectively. Afterward, a six-month period (August, 2016-January, 2017) of data from the ceilometer was analyzed. The results show that mean cloud base height during this period is 1.5 km, meaning that most clouds are in the category of low-level cloud.

Maternal height and child mortality in 42 developing countries.

Science.gov (United States)

Monden, Christiaan W S; Smits, Jeroen

2009-01-01

Previous research reports mixed results about the association between maternal height and child mortality. Some studies suggest that the negative association might be stronger in contexts with fewer resources. This hypothesis has yet not been tested in a cross-nationally comparative design. We use data on 307,223 children born to 194,835 women in 444 districts of 42 developing countries to estimate the association between maternal height and child mortality and test whether this association is modified by indicators at the level of the household (like sex, age and twin status of the child and socio-economic characteristics of the mother and her partner), district (regional level of development, public health facilities and female occupational attainment) and country (GDP per capita). We find a robust negative effect of logged maternal height on child mortality. The effect of maternal health is strongest for women with least education and is more important in the first year after birth and for twin births. The indicators of development at the district and country level do not modify the effect of maternal height. (c) 2008 Wiley-Liss, Inc.

Inhomogeneity in barrier height at graphene/Si (GaAs) Schottky junctions

OpenAIRE

Tomer, D.; Rajput, S.; Hudy, L. J.; Li, C. H.; Li, L.

2015-01-01

Graphene interfaced with a semiconductor forms a Schottky junction with rectifying properties, however, fluctuations in the Schottky barrier height are often observed. In this work, Schottky junctions are fabricated by transferring chemical vapor deposited monolayer graphene onto n-type Si and GaAs substrates. Temperature dependence of the barrier height and ideality factor are obtained by current-voltage measurements between 215 and 350 K. An increase in the zero bias barrier height and decr...

Falls from heights in and around the city of Batman.