WorldWideScience

Sample records for height variability resulting

  1. Variability of the Mixed-Layer Height Over Mexico City

    Science.gov (United States)

    García-Franco, J. L.; Stremme, W.; Bezanilla, A.; Ruiz-Angulo, A.; Grutter, M.

    2018-02-01

    The diurnal and seasonal variability of the mixed-layer height in urban areas has implications for ground-level air pollution and the meteorological conditions. Measurements of the backscatter of light pulses with a commercial lidar system were performed for a continuous period of almost six years between 2011 and 2016 in the southern part of Mexico City. The profiles were temporally and vertically smoothed, clouds were filtered out, and the mixed-layer height was determined with an ad hoc treatment of both the filtered and unfiltered profiles. The results are in agreement when compared with values of mixed-layer height reconstructed from, (i) radiosonde data, and (ii) surface and vertical column densities of a trace gas. The daily maxima of the mean mixed-layer height reach values > 3 km above ground level in the months of March-April, and are clearly lower (pollution episodes and the height of the mixed layer. The growth rate of the convective mixed-layer height has a seasonal behaviour, which is characterized together with the mixed-layer-height anomalies. A clear residual layer is evident from the backscattered signals recorded in days with specific atmospheric conditions, but also from the cloud-filtered mean diurnal profiles. The occasional presence of a residual layer results in an overestimation of the reported mixed-layer height during the night and early morning hours.

  2. Variability of the Mixed-Layer Height Over Mexico City

    Science.gov (United States)

    García-Franco, J. L.; Stremme, W.; Bezanilla, A.; Ruiz-Angulo, A.; Grutter, M.

    2018-06-01

    The diurnal and seasonal variability of the mixed-layer height in urban areas has implications for ground-level air pollution and the meteorological conditions. Measurements of the backscatter of light pulses with a commercial lidar system were performed for a continuous period of almost six years between 2011 and 2016 in the southern part of Mexico City. The profiles were temporally and vertically smoothed, clouds were filtered out, and the mixed-layer height was determined with an ad hoc treatment of both the filtered and unfiltered profiles. The results are in agreement when compared with values of mixed-layer height reconstructed from, (i) radiosonde data, and (ii) surface and vertical column densities of a trace gas. The daily maxima of the mean mixed-layer height reach values > 3 km above ground level in the months of March-April, and are clearly lower (behaviour, which is characterized together with the mixed-layer-height anomalies. A clear residual layer is evident from the backscattered signals recorded in days with specific atmospheric conditions, but also from the cloud-filtered mean diurnal profiles. The occasional presence of a residual layer results in an overestimation of the reported mixed-layer height during the night and early morning hours.

  3. Study of the electron density variability at fixed heights over San Juan and Tucuman

    International Nuclear Information System (INIS)

    Ezquer, R.G.; Mosert, M.; Radicella, S.M.; Jadur, C.A.

    2002-01-01

    The electron density (N) variability at fixed heights in the bottomside N profile over two Argentinean stations is presented. In this first study different solar conditions and some seasons are considered. The NHPC and CARP programs were used. The results show that, in general, for nighttime conditions the variability increases above 250 km. By noon the variability decreases with increasing the solar activity. At fixed heights, in general, the variability is larger by night than by day above 220 km. (author)

  4. Tillering of Marandu palisadegrass maintained at fixed or variable heights throughout the year

    Directory of Open Access Journals (Sweden)

    Denis D. Pessoa

    2016-05-01

    Full Text Available Satisfactory tillering is the basic attribute to ensure stability and productivity of a grass population. We aimed to develop an understanding of tillering in Urochloa brizantha syn. Brachiaria brizantha cv. Marandu (Marandu palisadegrass maintained at constant or variable heights during the various seasons of the year and to identify defoliation strategies that optimize tillering. In an experiment conducted in Uberlândia, Minas Gerais, Brazil, 3 defoliation strategies were studied: sward kept at 30 cm during the whole year (constant height; kept at 15 cm in fall/winter, 30 cm in spring and 45 cm in summer (increasing height; and kept at 45 cm in fall/winter, 30 cm in spring and 15 cm in the summer (decreasing height. The experiment was completely randomized, with 4 replicates. The following variables were evaluated: tiller appearance (TAR, mortality (TMR and survival (TSR rates; the balance (BAL between TAR and TMR; tiller population stability (TPS; and number of tillers/m2 (NT. In winter and late spring, TAR and BAL were low, while in early spring, the sward with decreasing height showed high TAR, BAL and TPS. The NT was higher when managed with increasing height than with other height strategies. Lowering pasture height from 45 to 30 cm after the winter increased TAR in early spring. Grazing studies seem warranted to assess how these results can be reproduced under grazing and how pasture yield and quality plus animal performance compare with those under the fixed grazing height regimen. Keywords: Defoliation, grazing management, pasture height, tillers, Urochloa brizantha.DOI: 10.17138/TGFT(4101-111 Normal 0 false false false PT-BR X-NONE X-NONE

  5. Experimental investigation of terahertz quantum cascade laser with variable barrier heights

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Aiting; Vijayraghavan, Karun; Belkin, Mikhail A., E-mail: mbelkin@ece.utexas.edu [Department of Electrical and Computer Engineering, The University of Texas at Austin, Austin, Texas 78758 (United States); Matyas, Alpar; Jirauschek, Christian [Institute for Nanoelectronics, Technische Universität München, D-80333 Munich (Germany); Wasilewski, Zbig R. [Department of Electrical and Computer Engineering, University of Waterloo, Waterloo, Ontario N2L 3G (Canada)

    2014-04-28

    We report an experimental study of terahertz quantum cascade lasers with variable barrier heights based on the Al{sub x}Ga{sub 1–x}As/GaAs material system. Two new designs are developed based on semiclassical ensemble Monte Carlo simulations using state-of-the-art Al{sub 0.15}Ga{sub 0.85}As/GaAs three-quantum-well resonant phonon depopulation active region design as a reference. The new designs achieved maximum lasing temperatures of 188 K and 172 K, as compared to the maximum lasing temperature of 191 K for the reference structure. These results demonstrate that terahertz quantum cascade laser designs with variable barrier heights provide a viable alternative to the traditional active region designs with fixed barrier composition. Additional design space offered by using variable barriers may lead to future improvements in the terahertz quantum cascade laser performance.

  6. A Study on the Relationships among Surface Variables to Adjust the Height of Surface Temperature for Data Assimilation.

    Science.gov (United States)

    Kang, J. H.; Song, H. J.; Han, H. J.; Ha, J. H.

    2016-12-01

    The observation processing system, KPOP (KIAPS - Korea Institute of Atmospheric Prediction Systems - Package for Observation Processing) have developed to provide optimal observations to the data assimilation system for the KIAPS Integrated Model (KIM). Currently, the KPOP has capable of processing almost all of observations for the KMA (Korea Meteorological Administration) operational global data assimilation system. The height adjustment of SURFACE observations are essential for the quality control due to the difference in height between observation station and model topography. For the SURFACE observation, it is usual to adjust the height using lapse rate or hypsometric equation, which decides values mainly depending on the difference of height. We have a question of whether the height can be properly adjusted following to the linear or exponential relationship solely with regard to the difference of height, with disregard the atmospheric conditions. In this study, firstly we analyse the change of surface variables such as temperature (T2m), pressure (Psfc), humidity (RH2m and Q2m), and wind components (U and V) according to the height difference. Additionally, we look further into the relationships among surface variables . The difference of pressure shows a strong linear relationship with difference of height. But the difference of temperature according to the height shows a significant correlation with difference of relative humidity than with the height difference. A development of reliable model for the height-adjustment of surface temperature is being undertaken based on the preliminary results.

  7. Seasonal variability of the Red Sea, from GRACE time-variable gravity and altimeter sea surface height measurements

    Science.gov (United States)

    Wahr, John; Smeed, David; Leuliette, Eric; Swenson, Sean

    2014-05-01

    Seasonal variability of sea surface height and mass within the Red Sea, occurs mostly through the exchange of heat with the atmosphere and wind-driven inflow and outflow of water through the strait of Bab el Mandab that opens into the Gulf of Aden to the south. The seasonal effects of precipitation and evaporation, of water exchange through the Suez Canal to the north, and of runoff from the adjacent land, are all small. The flow through the Bab el Mandab involves a net mass transfer into the Red Sea during the winter and a net transfer out during the summer. But that flow has a multi-layer pattern, so that in the summer there is actually an influx of cool water at intermediate (~100 m) depths. Thus, summer water in the southern Red Sea is warmer near the surface due to higher air temperatures, but cooler at intermediate depths (especially in the far south). Summer water in the northern Red Sea experiences warming by air-sea exchange only. The temperature profile affects the water density, which impacts the sea surface height but has no effect on vertically integrated mass. Here, we study this seasonal cycle by combining GRACE time-variable mass estimates, altimeter (Jason-1, Jason-2, and Envisat) measurements of sea surface height, and steric sea surface height contributions derived from depth-dependent, climatological values of temperature and salinity obtained from the World Ocean Atlas. We find good consistency, particularly in the northern Red Sea, between these three data types. Among the general characteristics of our results are: (1) the mass contributions to seasonal SSHT variations are much larger than the steric contributions; (2) the mass signal is largest in winter, consistent with winds pushing water into the Red Sea through the Strait of Bab el Mandab in winter, and out during the summer; and (3) the steric signal is largest in summer, consistent with summer sea surface warming.

  8. Use of hereditary for the detection of radioinduced variability in the height of tomato plants

    International Nuclear Information System (INIS)

    Fundora, Z.; Perez Talavera, S.; Auchet, F.; Moya, C.

    1986-01-01

    This paper is about the study of induced variability in the height of tomato plants from seeds treated with Co-60 gamma-rays. Hereditary coefficients in narrow sense were used trough progenitor-descendant regression of varieties irradiated on the control as indicator of the variability induced by the different doses

  9. Equations of bark thickness and volume profiles at different heights with easy-measurement variables

    Energy Technology Data Exchange (ETDEWEB)

    Cellini, J. M.; Galarza, M.; Burns, S. L.; Martinez-Pastur, G. J.; Lencinas, M. V.

    2012-11-01

    The objective of this work was to develop equations of thickness profile and bark volume at different heights with easy-measurement variables, taking as a study case Nothofagus pumilio forests, growing in different site qualities and growth phases in Southern Patagonia. Data was collected from 717 harvested trees. Three models were fitted using multiple, non-lineal regression and generalized linear model, by stepwise methodology, iteratively reweighted least squares method for maximum likelihood estimation and Marquardt algorithm. The dependent variables were diameter at 1.30 m height (DBH), relative height (RH) and growth phase (GP). The statistic evaluation was made through the adjusted determinant coefficient (r2-adj), standard error of the estimation (SEE), mean absolute error and residual analysis. All models presented good fitness with a significant correlation with the growth phase. A decrease in the thickness was observed when the relative height increase. Moreover, a bark coefficient was made to calculate volume with and without bark of individual trees, where significant differences according to site quality of the stands and DBH class of the trees were observed. It can be concluded that the prediction of bark thickness and bark coefficient is possible using DBH, height, site quality and growth phase, common and easy measurement variables used in forest inventories. (Author) 23 refs.

  10. Sea Surface Height Variability and Eddy Statistical Properties in the Red Sea

    KAUST Repository

    Zhan, Peng

    2013-01-01

    Satellite sea surface height (SSH) data over 1992-2012 are analyzed to study the spatial and temporal variability of sea level in the Red Sea. Empirical orthogonal functions (EOF) analysis suggests the remarkable seasonality of SSH in the Red Sea

  11. Evaluation of genetic variability for heading date and height in triticale obtained by induced mutations and artificial crosses

    International Nuclear Information System (INIS)

    Pandini, F.; Carvalho, F.I.F. de; Barbosa Neto, J.F.; Mittelmann, A.; Amaral, A.L. do

    1997-01-01

    The adjustment of adaptive characters such as heading date and height, allows one to arrange successive cultures and to apply efficient agronomic techniques, resulting in productivity increase. Methods that increase genetic variability have great significance in plant breeding, once they amplify the opportunities for selecting superior genotypes. The aim of this study was to evaluate the effect of induced mutations and reciprocal crosses in families segregating for heading date and height and to analyze the correlation between these characters. The populations were obtained from reciprocal crosses and induced mutation with gamma radiation. In the latter, radiation dosages of 0, 5, 10, 20, 40 kR were obtained from exposition to Cobalt - 60. Changes in the mean and variance in two triticale genotypes Triticale BR4 e EMBRAPAI8, were analyzed. The results obtained indicated families with wide segregation patterns for heading date and height and also suggested the possibility to identify families with distinct values compared to the control population for both characters and both genotypes. There was a tendency to reductions in height and increases in heading date for the families evaluated. However, there was not an expressive correlation between heading date and height for the majority of the treatments, therefore allowing the breeder to select plant types adapted to the environment of cultivation. (author) [pt

  12. Sea Surface Height Variability and Eddy Statistical Properties in the Red Sea

    KAUST Repository

    Zhan, Peng

    2013-05-01

    Satellite sea surface height (SSH) data over 1992-2012 are analyzed to study the spatial and temporal variability of sea level in the Red Sea. Empirical orthogonal functions (EOF) analysis suggests the remarkable seasonality of SSH in the Red Sea, and a significant correlation is found between SSH variation and seasonal wind cycle. A winding-angle based eddy identification algorithm is employed to derive the mesoscale eddy information from SSH data. Totally more than 5500 eddies are detected, belonging to 2583 eddy tracks. Statistics suggest that eddies generate over the entire Red Sea, with two regions in the central basin of high eddy frequency. 76% of the detected eddies have a radius ranging from 40km to 100km, of which both intensity and absolute vorticity decrease with eddy radius. The average eddy lifespan is about 5 weeks, and eddies with longer lifespan tend to have larger radius but less intensity. Different deformation rate exists between anticyclonic eddies (AEs) and cyclonic eddies (CEs), those eddies with higher intensity appear to be less deformed and more circular. Inspection of the 84 long-lived eddies suggests the AEs tend to move a little more northward than CEs. AE generation during summer is obviously lower than that during other seasons, while CE generation is higher during spring and summer. Other features of AEs and CEs are similar with both vorticity and intensity reaching the summer peaks in August and winter peaks in January. Inter-annual variability reveals that the eddies in the Red Sea are isolated from the global event. The eddy property tendencies are different from the south and north basin, both of which exhibit a two-year cycle. Showing a correlation coefficient of -0.91, Brunt–Väisälä frequency is negatively correlated with eddy kinetic energy (EKE), which results from AE activities in the high eddy frequency region. Climatological vertical velocity shear variation is identical with EKE except in the autumn, suggesting the

  13. Countermovement depth - a variable which clarifies the relationship between the maximum power output and height of a vertical jump.

    Science.gov (United States)

    Gajewski, Jan; Michalski, Radosław; Buśko, Krzysztof; Mazur-Różycka, Joanna; Staniak, Zbigniew

    2018-01-01

    The aim of this study was to identify the determinants of peak power achieved during vertical jumps in order to clarify relationship between the height of jump and the ability to exert maximum power. One hundred young (16.8±1.8 years) sportsmen participated in the study (body height 1.861 ± 0.109 m, body weight 80.3 ± 9.2 kg). Each participant performed three jump tests: countermovement jump (CMJ), akimbo countermovement jump (ACMJ), and spike jump (SPJ). A force plate was used to measure ground reaction force and to determine peak power output. The following explanatory variables were included in the model: jump height, body mass, and the lowering of the centre of mass before launch (countermovement depth). A model was created using multiple regression analysis and allometric scaling. The model was used to calculate the expected power value for each participant, which correlated strongly with real values. The value of the coefficient of determination R2 equalled 0.89, 0.90 and 0.98, respectively, for the CMJ, ACMJ, and SPJ jumps. The countermovement depth proved to be a variable strongly affecting the maximum power of jump. If the countermovement depth remains constant, the relative peak power is a simple function of jump height. The results suggest that the jump height of an individual is an exact indicator of their ability to produce maximum power. The presented model has a potential to be utilized under field condition for estimating the maximum power output of vertical jumps.

  14. Comparison of the effectiveness of analytical wake models for wind farm with constant and variable hub heights

    International Nuclear Information System (INIS)

    Wang, Longyan; Tan, Andy C.C.; Cholette, Michael; Gu, Yuantong

    2016-01-01

    Highlights: • The effectiveness of three analytical wake models is studied. • The results of the analytical wake models are compared with the CFD simulations. • The results of CFD simulation are verified by comparison to the offshore wind farm observation data. • The onshore wind farm with both constant and different hub height turbines are analyzed. • PARK model is able to predict the total wind farm power production well with tuned surface roughness value. - Abstract: Extensive power losses of wind farm have been witnessed due to the wake interactions between wind turbines. By applying analytical wake models which describe the wind speed deficits in the wake quantitatively, the power losses can be regained to a large extent through wind farm layout optimization, and this has been extensively reported in literature. Nevertheless, the effectiveness of the analytical wake models in predicting the wind farm power production have rarely been studied and compared for wind farm with both constant and variable wind turbine hub heights. In this study, the effectiveness of three different analytical wake models (PARK model, Larsen model and B-P model) is thoroughly compared over a wide range of wake properties. After the validation with the observation data from offshore wind farm, CFD simulations are used to verify the effectiveness of the analytical wake models for an onshore wind farm. The results show that when using the PARK model the surface roughness value (z 0 ) must be carefully tuned to achieve good performance in predicting the wind farm power production. For the other two analytical wake models, their effectiveness varies depending on the situation of wind farm (offshore or onshore) and the wind turbine hub heights (constant or variable). It was found that the results of B-P model agree well with the CFD simulations for offshore wind farm, but not for the onshore wind farm. The Larsen model is more accurate for the wind farm with variable wind turbine

  15. Geologic Variable Associated with Height of Yellow-Poplar Stand in the Bald Mountains of North Carolina

    Science.gov (United States)

    W. Henry McNab; Carl E. Merschat

    1990-01-01

    Quartz grain size and mylonitization, geologic variables determined fromrocks on sites, were associated with total height of yellow-poplar (Liriodendron tulipifera L.) standsand may be of value as independent variables in modeling tree growth from site characteristics. A predictive model containing quartz grain site and stand age accounted for about 54% of the...

  16. Recent variations in geopotential height associated with West African monsoon variability

    Science.gov (United States)

    Okoro, Ugochukwu K.; Chen, Wen; Nath, Debashis

    2018-02-01

    In the present study, the atmospheric circulation patterns associated with the seasonal West Africa (WA) monsoon (WAM) rainfall variability has been investigated. The observational rainfall data from the Climatic Research Unit (CRU) and atmospheric fields from the National Center for Environmental Prediction (NCEP) reanalysis 2, from 1979 to 2014, have been used. The rainfall variability extremes, classified as wet or dry years, are the outcomes of simultaneous 6-month SPI at the three rainfall zones, which shows increasing trends [Guinea Coast (GC = 0.012 year-1), Eastern Sudano Sahel (ESS = 0.045 year-1) and Western Sudano Sahel (WSS = 0.056 year-1) from Sen's slope]; however, it is significant only in the Sahel region (α = 0.05 and α = 0.001 at ESS and WSS, respectively, from Mann-Kendall test). The vertical profile of the geopotential height (GpH) during the wet and dry years reveals that the 700 hPa anomalies show remarkable pattern at about 8°N to 13°N. This shows varying correlation with the zonal averaged vertically integrated moisture flux convergence and rainfall anomalies, respectively, as well as the oceanic pulsations indexes [Ocean Nino Index (ONI) and South Atlantic Ocean dipole index (SAODI), significant from t test], identified as precursors to the Sahel and GC rainfall variability respectively. The role of GpH anomalies at 700 hPa has been identified as the facilitator to the West African Westerly Jet's input to the moisture flux transported over the WA. This is a new perspective of the circulation processes associated with WAM and serves as a basis for modeling investigations.

  17. Variable valve trains for internal combustion engines to control the valve height and the opening time; Variable Ventiltriebe fuer Verbrennungsmotoren zur Veraenderung von Ventilhub und Oeffnungsdauer

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Gunther [ThyssenKrupp Presta TecCenter AG, Eschen (Liechtenstein). R and D Projects

    2009-11-15

    The PDVC (Presta Delta Valve Control) continuously variable valve lift system is a mechanical system of valve control for achieving optimum performance and resulting in improved fuel consumption and reduced emissions across the entire operating range of the combustion engine. The continuous variability allows for engine load control by adjusting the valve height and therefore can also be used to replace the traditional throttle. The advantages are lower fuel consumption, reduction in emissions, quicker engine response, higher torque during the low speed range as well as more stable idling. The PSVC (Presta Shiftable Valve Control) is a 3 step shiftable valve lift system that offers the possibility to achieve a major part of these performance and associated consumption benefits with a simpler and therefore more cost-effective system. (orig.)

  18. Direct Measurement of Tree Height Provides Different Results on the Assessment of LiDAR Accuracy

    Directory of Open Access Journals (Sweden)

    Emanuele Sibona

    2016-12-01

    Full Text Available In this study, airborne laser scanning-based and traditional field-based survey methods for tree heights estimation are assessed by using one hundred felled trees as a reference dataset. Comparisons between remote sensing and field-based methods were applied to four circular permanent plots located in the western Italian Alps and established within the Alpine Space project NewFor. Remote sensing (Airborne Laser Scanning, ALS, traditional field-based (indirect measurement, IND, and direct measurement of felled trees (DIR methods were compared by using summary statistics, linear regression models, and variation partitioning. Our results show that tree height estimates by Airborne Laser Scanning (ALS approximated to real heights (DIR of felled trees. Considering the species separately, Larix decidua was the species that showed the smaller mean absolute difference (0.95 m between remote sensing (ALS and direct field (DIR data, followed by Picea abies and Pinus sylvestris (1.13 m and 1.04 m, respectively. Our results cannot be generalized to ALS surveys with low pulses density (<5/m2 and with view angles far from zero (nadir. We observed that the tree heights estimation by laser scanner is closer to actual tree heights (DIR than traditional field-based survey, and this was particularly valid for tall trees with conical shape crowns.

  19. Should we consider steps with variable height for a safer stair negotiation in older adults?

    Science.gov (United States)

    Kunzler, Marcos R; da Rocha, Emmanuel S; Dos Santos, Christielen S; Ceccon, Fernando G; Priario, Liver A; Carpes, Felipe P

    2018-01-01

    Effects of exercise on foot clearances are important. In older adults variations in foot clearances during walking may lead to a fall, but there is a lack of information concerning stair negotiation in older adults. Whether a condition of post exercise changes foot clearances between steps of a staircase in older adults still unknown. To determine differences in clearances when older adults negotiate different steps of a staircase before and after a session of aerobic exercise. Kinematics data from 30 older adults were acquired and the toe and heel clearances were determined for each step. Clearances were compared between the steps. Smaller clearances were found at the highest step during ascending and descending, which was not changed by exercise. Smaller clearances suggest higher risk of tripping at the top of the staircase, regardless of exercise. A smaller step at the top of a short flight of stairs could reduce chances of tripping in older adults. It suggests that steps with variable height could make stair negotiation safer in older adults. This hypothesis should be tested in further studies.

  20. Variability of the Brunt-Väisälä frequency at the OH* layer height

    Science.gov (United States)

    Wüst, Sabine; Bittner, Michael; Yee, Jeng-Hwa; Mlynczak, Martin G.; Russell, James M., III

    2017-12-01

    In and near the Alpine region, the most dense subnetwork of identical NDMC (Network for the Detection of Mesospheric Change, https://www.wdc.dlr.de/ndmc/) instruments can be found: five stations are equipped with OH* spectrometers which deliver a time series of mesopause temperature for each cloudless or only partially cloudy night. These measurements are suitable for the derivation of the density of gravity wave potential energy, provided that the Brunt-Väisälä frequency is known. However, OH* spectrometers do not deliver vertically resolved temperature information, which is necessary for the calculation of the Brunt-Väisälä frequency. Co-located measurements or climatological values are needed. We use 14 years of satellite-based temperature data (TIMED-SABER, 2002-2015) to investigate the inter- and intra-annual variability of the Brunt-Väisälä frequency at the OH* layer height between 43.93-48.09° N and 5.71-12.95° E and provide a climatology.

  1. Seasonal variability in virtual height of ionospheric f/sub 2/ layer at the pakistan atmospheric region

    International Nuclear Information System (INIS)

    Jilani, A.A.; Afridi, F.A.K.; Mian, K.; Zai, M.A.K.Y.

    2013-01-01

    The aim of this study was to assess the seasonal variability in virtual height of ionospheric F/sub 2/ layer for Pakistan's atmospheric region (PAR). In this communication virtual height variations have been analyzed by the descriptive statistical techniques. These methodologies comprise an autoregressive strategy, linear regression and polynomial regression. The relevance of these models has been illuminated using predicted values of different parameters under the seasonal variation of ionospheric F/sub 2/ layer in virtual height that affect the radio wave propagation through the ionosphere. These techniques are implemented to theorize the physical process of varying the virtual heights that leads this study towards formulating the variations due to interaction of radio wave propagation with this ionospheric layer. (author)

  2. Environmental survey at the AAEC Research Establishment, Lucas Heights - results for 1979

    International Nuclear Information System (INIS)

    Giles, M.S.; Dudaitis, A.

    1980-09-01

    This report presents the results of the environmental survey at the AAEC Research Establishment, Lucas Heights, during 1979. They show that the only radioactivity detected which could be of AAECRE origin and which could also be ingested by humans was due to tritium. The maximum credible dose which a member of the public could receive from this radioactivity is calculated to be one ten thousandth of the derived working limit consistent with the latest recommendations of the International Commission on Radiological Protection

  3. Wake interaction and power production of variable height model wind farms

    DEFF Research Database (Denmark)

    Vested, Malene Hovgaard; Hamilton, N.; Sørensen, Jens Nørkær

    2014-01-01

    of comparison. It was found that downstream of the exit row wind turbine, the power was increased by 25% in the case of a staggered height configuration. This is partly due to the fact that the taller turbines reach into a flow area with a softened velocity gradient. Another aspect is that the wake downstream...

  4. Wake interaction and power production of variable height model wind farms

    International Nuclear Information System (INIS)

    Vested, M H; Sørensen, J N; Hamilton, N; Cal, R B

    2014-01-01

    Understanding wake dynamics is an ongoing research topic in wind energy, since wakes have considerable effects on the power production when wind turbines are placed in a wind farm. Wind tunnel experiments have been conducted to study the wake to wake interaction in a model wind farm in tandem with measurements of the extracted power. The aim is to investigate how alternating mast height influences the interaction of the wakes and the power production. Via the use of stereo-particle image velocimetry, the flow field was obtained in the first and last rows of the wind turbine array as a basis of comparison. It was found that downstream of the exit row wind turbine, the power was increased by 25% in the case of a staggered height configuration. This is partly due to the fact that the taller turbines reach into a flow area with a softened velocity gradient. Another aspect is that the wake downstream of a tall wind turbine to some extent passes above the standard height wind turbine. Overall the experiments show that the velocity field downstream of the exit row changes considerably when the mast height is alternating

  5. INFLUENCE OF BODY HEIGHT, BODY WEIGHT AND THE AGE ON THE RESULTS ACHIEVED BY MAN-MARATHONERS IN A MARATHON RACE

    Directory of Open Access Journals (Sweden)

    Naser Rašiti Naser

    2011-09-01

    Full Text Available The research is conducted on a sample of 100 successful man marathoners who has taken part in ten of the most popular marathon races. The sample of entities includes ten of the best placed marathoners in each race held during the year 2008. The aim of the research is to assess the influence of the body height, weight and the age of the marathoners on the final result in the race. The collected data is processed by the basic descriptive parameters. The entities have the average weight of 56.94 kg, with the average height of 168.98 cm, at the average age of 29.75, with the achieved average result of 2:13.23 hours in the race. In the intercorrelation matrix only one significant coefficient of correlation is obtained (p<0.001 between the body height and body weight. By the regressive analysis the influence of the predictory variables (height, weight and age on the criteria variable – sig. =0, 21 (the result of the marathon is not confirmed, which provides only 15% (RO²=.302 of analysis in the common ground of variability. The rest of 91% in analysing the total variability of the criteria variable can be ascribed to some other anthropologic characteristics, and mainly to the functional characteristics of anaerobic type.

  6. Countermovement jump height: gender and sport-specific differences in the force-time variables.

    Science.gov (United States)

    Laffaye, Guillaume; Wagner, Phillip P; Tombleson, Tom I L

    2014-04-01

    The goal of this study was to assess (a) the eccentric rate of force development, the concentric force, and selected time variables on vertical performance during countermovement jump, (b) the existence of gender differences in these variables, and (c) the sport-specific differences. The sample was composed of 189 males and 84 females, all elite athletes involved in college and professional sports (primarily football, basketball, baseball, and volleyball). The subjects performed a series of 6 countermovement jumps on a force plate (500 Hz). Average eccentric rate of force development (ECC-RFD), total time (TIME), eccentric time (ECC-T), Ratio between eccentric and total time (ECC-T:T) and average force (CON-F) were extracted from force-time curves and the vertical jumping performance, measured by impulse momentum. Results show that CON-F (r = 0.57; p differ between both sexes (p differ, showing a similar temporal structure. The best way to jump high is to increase CON-F and ECC-RFD thus minimizing the ECC-T. Principal component analysis (PCA) accounted for 76.8% of the JH variance and revealed that JH is predicted by a temporal and a force component. Furthermore, the PCA comparison made among athletes revealed sport-specific signatures: volleyball players revealed a temporal-prevailing profile, a weak-force with large ECC-T:T for basketball players and explosive and powerful profiles for football and baseball players.

  7. Planetary boundary layer height over the Indian subcontinent: Variability and controls with respect to monsoon

    Science.gov (United States)

    Sathyanadh, Anusha; Prabhakaran, Thara; Patil, Chetana; Karipot, Anandakumar

    2017-10-01

    Planetary boundary layer (PBL) height characteristics over the Indian sub-continent at diurnal to seasonal scales and its controlling factors in relation to monsoon are investigated. The reanalysis (Modern Era Retrospective analysis for Research and Applications, MERRA) PBL heights (PBLH) used for the study are validated against those derived from radiosonde observations and radio occultation air temperature and humidity profiles. The radiosonde observations include routine India Meteorological Department observations at two locations (coastal and an inland) for one full year and campaign based early afternoon radiosonde observations at six inland locations over the study region for selected days from May-September 2011. The temperature and humidity profiles from radio occultations spread over the sub-continent at irregular timings during the year 2011. The correlations and root mean square errors are in the range 0.74-0.83 and 407 m-643 m, respectively. Large pre-monsoon, monsoon and post-monsoon variations in PBL maximum height (1000 m-4000 m), time of occurrence of maximum height (11:00 LST-17:00 LST) and growth rate (100 to 400 m h- 1) are noted over the land, depending on geographical location and more significantly on the moisture availability which influences the surface sensible and latent heat fluxes. The PBLH variations associated with active-break intra-seasonal monsoon oscillations are up to 1000 m over central Indian locations. Inter relationship between the PBLH and the controlling factors, i.e. Evaporative Fraction, net radiation, friction velocity, surface Richardson number, and scalar diffusivity fraction, show significant variation between dry and wet PBL regimes, which also varies with geographical location. Evaporative fraction has dominant influence on the PBLH over the region. Enhanced entrainment during monsoon contributes to reduction in PBLH, whereas the opposite effect is noted during dry period. Linear regression, cross wavelet and

  8. A combinatorial and probabilistic study of initial and end heights of descents in samples of geometrically distributed random variables and in permutations

    Directory of Open Access Journals (Sweden)

    Helmut Prodinger

    2007-01-01

    Full Text Available In words, generated by independent geometrically distributed random variables, we study the l th descent, which is, roughly speaking, the l th occurrence of a neighbouring pair ab with a>b. The value a is called the initial height, and b the end height. We study these two random variables (and some similar ones by combinatorial and probabilistic tools. We find in all instances a generating function Ψ(v,u, where the coefficient of v j u i refers to the j th descent (ascent, and i to the initial (end height. From this, various conclusions can be drawn, in particular expected values. In the probabilistic part, a Markov chain model is used, which allows to get explicit expressions for the heights of the second descent. In principle, one could go further, but the complexity of the results forbids it. This is extended to permutations of a large number of elements. Methods from q-analysis are used to simplify the expressions. This is the reason that we confine ourselves to the geometric distribution only. For general discrete distributions, no such tools are available.

  9. Low frequency variability of the Indian Ocean from TOPEX/POSEIDON sea surface height anomalies

    Digital Repository Service at National Institute of Oceanography (India)

    Somayajulu, Y.K.; Murty, V.S.N.; Sarma, Y.V.B.

    and off Sumatra present large variability on both seasonal and inter-annual time scales. The SSH anomalies off Sumatra show dominant influence of warm (cold) ENSO events with peak negative (positive) anomalies coinciding with El Nino (La Nina...

  10. One year variability of peak heights, heterozygous balance and inter-locus balance for the DNA positive control of AmpFℓSTR© Identifiler© STR kit.

    Science.gov (United States)

    Debernardi, A; Suzanne, E; Formant, A; Pène, L; Dufour, A B; Lobry, J R

    2011-01-01

    Multivariate analyses of 205 positive control experiments in an AmpFℓSTR© Identifiler© STR kit were used to analyze the factors affecting peak heights at 16 loci. Peak heights were found to be highly correlated between loci and there was evidence for a difference in sensitivity of the two genetic analyzers in the blue channel. Heterozygous balance response at 10 loci was found to behave as a random variable following a beta-distribution with typical median values of 90%, without locus or genetic analyzer effect. Inter-locus balance at 16 loci was influenced by the blue channel effect and a temporal switch of unexplained origin. The implications of these results for the choice of minimum threshold values in quality control are discussed. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  11. CRITICAL HEIGHT FOR THE DESTABILIZATION OF SOLAR PROMINENCES: STATISTICAL RESULTS FROM STEREO OBSERVATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Liu Kai; Wang Yuming; Wang Shui; Shen Chenglong, E-mail: ymwang@ustc.edu.cn [CAS Key Laboratory of Geospace Environment, Department of Geophysics and Planetary Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2012-01-10

    At which height is a prominence inclined to be unstable, or where is the most probable critical height for the prominence destabilization? This question was statistically studied based on 362 solar limb prominences well recognized by Solar Limb Prominence Catcher and Tracker from 2007 April to the end of 2009. We found that there are about 71% disrupted prominences (DPs), among which about 42% of them did not erupt successfully and about 89% of them experienced a sudden destabilization process. After a comprehensive analysis of the DPs, we discovered the following: (1) Most DPs become unstable at a height of 0.06-0.14 R{sub Sun} from the solar surface, and there are two most probable critical heights at which a prominence is very likely to become unstable, the first one is 0.13 R{sub Sun} and the second one is 0.19 R{sub Sun }. (2) An upper limit for the erupting velocity of eruptive prominences (EPs) exists, which decreases following a power law with increasing height and mass; accordingly, the kinetic energy of EPs has an upper limit too, which decreases as the critical height increases. (3) Stable prominences are generally longer and heavier than DPs, and not higher than 0.4 R{sub Sun }. (4) About 62% of the EPs were associated with coronal mass ejections (CMEs); but there is no difference in apparent properties between EPs associated with CMEs and those that are not.

  12. CRITICAL HEIGHT FOR THE DESTABILIZATION OF SOLAR PROMINENCES: STATISTICAL RESULTS FROM STEREO OBSERVATIONS

    International Nuclear Information System (INIS)

    Liu Kai; Wang Yuming; Wang Shui; Shen Chenglong

    2012-01-01

    At which height is a prominence inclined to be unstable, or where is the most probable critical height for the prominence destabilization? This question was statistically studied based on 362 solar limb prominences well recognized by Solar Limb Prominence Catcher and Tracker from 2007 April to the end of 2009. We found that there are about 71% disrupted prominences (DPs), among which about 42% of them did not erupt successfully and about 89% of them experienced a sudden destabilization process. After a comprehensive analysis of the DPs, we discovered the following: (1) Most DPs become unstable at a height of 0.06-0.14 R ☉ from the solar surface, and there are two most probable critical heights at which a prominence is very likely to become unstable, the first one is 0.13 R ☉ and the second one is 0.19 R ☉ . (2) An upper limit for the erupting velocity of eruptive prominences (EPs) exists, which decreases following a power law with increasing height and mass; accordingly, the kinetic energy of EPs has an upper limit too, which decreases as the critical height increases. (3) Stable prominences are generally longer and heavier than DPs, and not higher than 0.4 R ☉ . (4) About 62% of the EPs were associated with coronal mass ejections (CMEs); but there is no difference in apparent properties between EPs associated with CMEs and those that are not.

  13. Adult Height after Growth Hormone Treatment at Pubertal Onset in Short Adolescents Born Small for Gestational Age: Results from a Belgian Registry-Based Study

    Directory of Open Access Journals (Sweden)

    M. Thomas

    2018-01-01

    Full Text Available Objectives. Information on the efficacy of GH treatment in short SGA children starting their treatment in adolescence is limited. Therefore, adult height (AH, total height gain, and pubertal height gain were evaluated in short SGA children who started GH treatment at pubertal onset. Patient and Methods. Growth data of 47 short SGA adolescents (22 boys who started GH treatment at pubertal onset (PUB group were compared with results from 27 short SGA patients (11 boys who started GH therapy at least 1 year before pubertal onset (PrePUB group. Results. The PUB group achieved a mean (±SD total height gain of 0.8 ± 0.7 SDS and an AH of −2.5 ± 0.7 SDS after 4.1 ± 1.1 years of GH treatment with a dosage of 41.8 ± 8.4 μg/kg/day. These results were comparable with those in the PrePUB group, which was treated for a longer duration (5.8 ± 2.1 years, resulting in a total height gain of 1.1 ± 0.7 SDS and an AH of −2.1 ± 1.0 SDS. Multiple regression analysis showed a significantly lower height gain in pubertal patients, females, and patients weighing less at start of GH treatment. An AH above −2 SDS and above the parent-specific lower limit of height was, respectively, reached in 28% and 70% of PUB and 44% and 67% of PrePUB patients (NS. AH SDS was positively correlated with the height SDS at start of GH. Conclusions. Short SGA adolescents starting GH therapy at an early pubertal stage have a modest and variable height gain. A normal AH can be expected in one third of the patients, especially in those with a smaller height deficit at onset of GH treatment.

  14. First result from x-ray pulse height analyzer with radial scanning system for LHD

    Science.gov (United States)

    Muto, Sadatsugu; Morita, Shigeru

    2001-01-01

    Radial profiles of x-ray spectrum have been successfully obtained using an assembly of x-ray pulse height analyzer in large helical device. The observed profile is obtained from plasma heated by ICRF and neutral beam injection (NBI). As a detector, Si(Li) semiconductor is used with a histogramming memory and analog-to-digital converter (ADC) basically working at high counting rate up to 500 kcps. In routine operation a count rate of 62 kcps has been normally obtained with energy resolution better than 400 eV at iron Kα line. The assembly is equipped with four detectors and a radial scanning system which modulates sight lines of the detectors in major radius direction. The profiles of electron temperature and the intensity of metallic impurities have been obtained with a spatial resolution of a few centimeters. Measured electron temperature is in good agreement with that from Thomson scattering. The system is applicable to steady-state discharge. The design philosophy of the assembly and recent results on the performance tests are also presented.

  15. Evaluation of 4 mm implants in mandibular edentulous patients with reduced bone height. Surgical preliminary results

    Directory of Open Access Journals (Sweden)

    J.L. Calvo-Guirado

    2014-06-01

    Full Text Available Aim: Growing evidence has suggested the utility of short dental implants for oral reconstructive procedures in clinical situations of limited vertical bone height. The aim of this short comunication was to evaluate the clinical use of implants < 10 mm in length and to determine short implant-supported prosthesis success in the atrophic jaw. Materials and methods: Six women and three men were recruited for the treatment of edentulous mandibles. A total of 6 implants were inserted in each patient: two anterior implants of conventional lenght and four posterior 4 mm Titanium Zirconium (TiZr implants. The insertion torque and bone denisty were evaluated. Results: The mean insertion torque for the 4 mm implants was lower than for conventional ones, without any statistical difference. Moreover, most of the patients (88% showed a D2 bone type. Conclusion: The provision of short implant-supported prostheses in patients with atrophic alveolar ridges appears to be a successful treatment option in the short term; however, more scientific evidence is needed for the long term.

  16. Increased height standard deviation scores in response to growth hormone therapy to near-adult height in older children with delayed skeletal maturation: results from the ANSWER Program.

    Science.gov (United States)

    Ross, Judith L; Lee, Peter A; Gut, Robert; Germak, John

    2015-01-01

    A primary goal of recombinant human growth hormone therapy (GHT) in children is attaining normal adult height. In this study, children with growth hormone deficiency (GHD) (including isolated idiopathic growth hormone deficiency [IGHD] and multiple pituitary hormone deficiency [MPHD]), idiopathic short stature (ISS), and Turner syndrome (TS) were evaluated for near-adult height (NAH) and percent achieving NAH within the normal range after approximately 4 years of GHT. Data from the American Norditropin® Web-Enabled Research (ANSWER) Program were analyzed for NAH from age at treatment start (ATS) (i.e., referral age as defined by age at enrollment in the study) to last clinic visit using one of the following two criteria: 1) age ≥18 years, or 2) if male: ≥16 years and height velocity (HV) standard deviation score (HSDS) ≤ -2, and either GHD (n = 201), ISS (n = 19), or TS (n = 41). The main outcome measures included HSDS and corrected HSDS (HSDS-target HSDS) in response to GH treatment, and correlation of ATS with NAH HSDS. Mean (± SD) chronological and bone ages at baseline were 14.0 ± 2.1 years and 11.7 ± 2.0 years, respectively, and mean GHT duration was 4.0 ± 1.6 years. Mean HSDS (baseline to NAH; GHD: -2.7 to -1.0; ISS: -2.8 to -1.4; TS: -3.0 to -1.8) and mean corrected HSDS (baseline to NAH; GHD: -2.1 to -0.3; ISS: -2.1 to -0.6; TS: -1.8 to -0.6) increased across diagnostic indications. Percentages of patients reaching near-adult HSDS > -2 were GHD: 87.6%; ISS: 78.9%; TS: 65.8%. Significant negative correlations were found between ATS and NAH HSDS when analyzed by sex. Despite a relatively advanced childhood age, the majority of GH-treated patients attained mean near-adult HSDS within the normal range (HSDS > -2). Negative correlations of ATS with near-adult HSDS indicate that an earlier age at treatment start would likely have resulted in greater adult height achieved in both male and female patients.

  17. Forage accumulation in brachiaria grass under continuous grazing with single or variable height during the seasons of the year

    Directory of Open Access Journals (Sweden)

    Manoel Eduardo Rozalino Santos

    2013-05-01

    Full Text Available The objective of this study was to evaluate grazing management strategies of Brachiaria decumbens cv. Basilisk managed with different heights under continuous grazing with cattle. Two grazing management strategies were evaluated: maintenance of pasture with an average height of 25 cm throughout the experimental period and maintenance of pasture on the average of 15 cm in height during winter, up to 25 cm from the beginning of spring. The split-plot scheme and the randomized block design with four replications were adopted. The grazing management strategies corresponded to the primary factor, while the seasons (winter, spring and summer corresponded to secondary factor. The reduction of the average sward height to 15 cm in the winter resulted, when compared with pasture maintained at 25 cm, in overall higher growth rates (95 kg/ha.day DM and leaf blade (66.1 kg/ha.day DM, as well as higher rates of total accumulation (81.5 kg/ha.day DM and leaf blade (52.6 kg/ha.day DM. The accumulated forage production (from winter to summer was higher in the pasture lowered to 15 cm in winter (25.6 t/ha DM compared with that managed with an average height of 25 cm (22.2 t/ha DM. Regarding the seasons of the year, in the winter, there were lower rates of overall growth (6.4 kg/ha.day DM, leaf blade (5.6 kg/ha.day DM and pseudostem (0.8 kg/ha.day DM, and also lower total (-6.6 kg/ha.day DM and leaf blade (-7.5 kg/ha.day DM accumulation rates. In the spring there was a higher rate of leaf senescence (22.4 kg/ha.day DM. The accumulation of forage is incremented when the pasture of B. decumbens is lowered to 15 cm during the winter, and in the spring and summer, its average height is increased to 25 cm.

  18. Multimodel simulations of Arctic Ocean sea surface height variability in the period 1970-2009

    DEFF Research Database (Denmark)

    Koldunov, Nikolay V.; Serra, Nuno; Koehl, Armin

    2014-01-01

    analysis of the three time periods 1987-1992, 1993-2002, and 2003-2009, corresponding to the transition times between cyclonic and anticyclonic regimes of the atmospheric circulation over the Arctic, revealed an unusual increase of SSH in the Amerasian basin during 2003-2009. Results from this model...

  19. Wave Height and Water Level Variability on Lakes Michigan and St Clair

    Science.gov (United States)

    2012-10-01

    Observations: http://www.ssec.wisc.edu/sose/glwx_activity.html 4. NASA Atlas of Extratropical Storm Tracks: http://data.giss.nasa.gov/stormtracks...term meteorological, ice, wave, and water level measurements. 15. SUBJECT TERMS Base flood elevation Coastal flood Extratropical storms Great...Box 1027 Detroit, MI 48231-1027 ERDC/CHL TR-12-23 ii Abstract The Great Lakes are subject to coastal flooding as a result of severe storms

  20. Effects of variable transformations on errors in FORM results

    International Nuclear Information System (INIS)

    Qin Quan; Lin Daojin; Mei Gang; Chen Hao

    2006-01-01

    On the basis of studies on second partial derivatives of the variable transformation functions for nine different non-normal variables the paper comprehensively discusses the effects of the transformation on FORM results and shows that senses and values of the errors in FORM results depend on distributions of the basic variables, whether resistances or actions basic variables represent, and the design point locations in the standard normal space. The transformations of the exponential or Gamma resistance variables can generate +24% errors in the FORM failure probability, and the transformation of Frechet action variables could generate -31% errors

  1. GH treatment to final height produces similar height gains in patients with SHOX deficiency and turner syndrome: Results of a multicenter trial

    NARCIS (Netherlands)

    W.F. Blum (Werner); J.L. Ross (J.); A.G. Zimmermann (Alan); C.A. Quigley (Charmian); C.J. Child (Christopher); G. Kalifa (Gabriel); C.L. Deal (Cheri Lynn); S.L.S. Drop (Stenvert); G. Rappold (G.); G. Cutler (Gordon)

    2013-01-01

    textabstractContext: Growth impairment in short stature homeobox-containing gene (SHOX) deficiency and Turner syndrome share a similar etiology. Because of the established effect of GH treatment on height in patients with Turner syndrome, we hypothesized that GH therapy would also stimulate growth

  2. GH treatment to final height produces similar height gains in patients with SHOX deficiency and Turner syndrome: results of a multicenter trial.

    Science.gov (United States)

    Blum, Werner F; Ross, Judith L; Zimmermann, Alan G; Quigley, Charmian A; Child, Christopher J; Kalifa, Gabriel; Deal, Cheri; Drop, Stenvert L S; Rappold, Gudrun; Cutler, Gordon B

    2013-08-01

    Growth impairment in short stature homeobox-containing gene (SHOX) deficiency and Turner syndrome share a similar etiology. Because of the established effect of GH treatment on height in patients with Turner syndrome, we hypothesized that GH therapy would also stimulate growth in patients with SHOX deficiency. Our objectives were to evaluate long-term efficacy of GH treatment in short patients with SHOX deficiency and to compare the effect on final (adult) height (FH) in patients with SHOX deficiency and Turner syndrome. A prospective, multinational, open-label, randomized 3-arm study consisting of a 2-year control period and a subsequent extension period to FH. The treatment groups were 1) SHOX-D-C/GH (untreated during the control period, GH-treated during the extension), 2) SHOX-D-GH/GH, and 3) Turner-GH/GH (GH-treated during both study periods). Short-statured prepubertal patients with genetically confirmed SHOX deficiency (n = 49) or Turner syndrome (n = 24) who participated in the extension. Depending on the study arm, patients received a daily sc injection of 0.05 mg/kg recombinant human GH from start of the study or start of the extension until attainment of FH or study closure. Height SD score gain from start of GH treatment to FH was similar between the combined SHOX-deficient groups (n = 28, 1.34 ± 0.18 [least-squares mean ± SE]) and the Turner group (n = 19, 1.32 ± 0.22). In this FH population, 57% of the patients with SHOX deficiency and 32% of the patients with Turner syndrome achieved a FH greater than -2 SD score. GH treatment in short children with SHOX deficiency showed similar long-term efficacy as seen in girls with Turner syndrome.

  3. THE TIME DOMAIN SPECTROSCOPIC SURVEY: VARIABLE SELECTION AND ANTICIPATED RESULTS

    Energy Technology Data Exchange (ETDEWEB)

    Morganson, Eric; Green, Paul J. [Harvard Smithsonian Center for Astrophysics, 60 Garden St, Cambridge, MA 02138 (United States); Anderson, Scott F.; Ruan, John J. [Department of Astronomy, University of Washington, Box 351580, Seattle, WA 98195 (United States); Myers, Adam D. [Department of Physics and Astronomy, University of Wyoming, Laramie, WY 82071 (United States); Eracleous, Michael; Brandt, William Nielsen [Department of Astronomy and Astrophysics, 525 Davey Laboratory, The Pennsylvania State University, University Park, PA 16802 (United States); Kelly, Brandon [Department of Physics, Broida Hall, University of California, Santa Barbara, CA 93106-9530 (United States); Badenes, Carlos [Department of Physics and Astronomy and Pittsburgh Particle Physics, Astrophysics and Cosmology Center (PITT PACC), University of Pittsburgh, 3941 O’Hara St, Pittsburgh, PA 15260 (United States); Bañados, Eduardo [Max-Planck-Institut für Astronomie, Königstuhl 17, D-69117 Heidelberg (Germany); Blanton, Michael R. [Center for Cosmology and Particle Physics, Department of Physics, New York University, 4 Washington Place, New York, NY 10003 (United States); Bershady, Matthew A. [Department of Astronomy, University of Wisconsin, 475 N. Charter St., Madison, WI 53706 (United States); Borissova, Jura [Instituto de Física y Astronomía, Universidad de Valparaíso, Av. Gran Bretaña 1111, Playa Ancha, Casilla 5030, and Millennium Institute of Astrophysics (MAS), Santiago (Chile); Burgett, William S. [GMTO Corp, Suite 300, 251 S. Lake Ave, Pasadena, CA 91101 (United States); Chambers, Kenneth, E-mail: emorganson@cfa.harvard.edu [Institute for Astronomy, University of Hawaii at Manoa, Honolulu, HI 96822 (United States); and others

    2015-06-20

    We present the selection algorithm and anticipated results for the Time Domain Spectroscopic Survey (TDSS). TDSS is an Sloan Digital Sky Survey (SDSS)-IV Extended Baryon Oscillation Spectroscopic Survey (eBOSS) subproject that will provide initial identification spectra of approximately 220,000 luminosity-variable objects (variable stars and active galactic nuclei across 7500 deg{sup 2} selected from a combination of SDSS and multi-epoch Pan-STARRS1 photometry. TDSS will be the largest spectroscopic survey to explicitly target variable objects, avoiding pre-selection on the basis of colors or detailed modeling of specific variability characteristics. Kernel Density Estimate analysis of our target population performed on SDSS Stripe 82 data suggests our target sample will be 95% pure (meaning 95% of objects we select have genuine luminosity variability of a few magnitudes or more). Our final spectroscopic sample will contain roughly 135,000 quasars and 85,000 stellar variables, approximately 4000 of which will be RR Lyrae stars which may be used as outer Milky Way probes. The variability-selected quasar population has a smoother redshift distribution than a color-selected sample, and variability measurements similar to those we develop here may be used to make more uniform quasar samples in large surveys. The stellar variable targets are distributed fairly uniformly across color space, indicating that TDSS will obtain spectra for a wide variety of stellar variables including pulsating variables, stars with significant chromospheric activity, cataclysmic variables, and eclipsing binaries. TDSS will serve as a pathfinder mission to identify and characterize the multitude of variable objects that will be detected photometrically in even larger variability surveys such as Large Synoptic Survey Telescope.

  4. Height-obesity relationship in school children in Sub-Saharan Africa: results of a cross-sectional study in Cameroon.

    Science.gov (United States)

    Navti, Lifoter K; Ferrari, Uta; Tange, Emmanuel; Parhofer, Klaus G; Pozza, Susanne Bechtold-Dalla

    2015-03-26

    In developed nations, taller children exhibit a greater propensity to overweight/obesity. This study investigates whether this height-adiposity relationship holds true for Cameroon children using two parameters of adiposity including body mass index (BMI) and waist circumference (WC). In 557 children (287 boys and 270 girls, mean age 9.0 ± 1.8 years) from the North West Region of Cameroon height, weight and WC were measured and BMI calculated. Variables were converted to standard deviation scores (SDS). Participants were divided into quartiles of height SDS, then mean of age and sex-standardized body fat parameters compared across quartiles. The frequency of excess adiposity was calculated within each quartile. Correlation and regression analysis were used to assess height-adiposity relationships. Multiple comparisons indicated a significant increase in mean BMI (-0.08 to 0.65) and WC (-0.11 to 0.87) SDSs with increasing quartiles of height SDS. Frequency of overweight/obesity and abdominal overweight/obesity was highest among children with highest height SDS (30.2 - 33.1%) and lowest in their shortest peers (0.7 - 5.0%). There was a linear relationship between height SDS and BMI SDS (R(2) = 0.087, p economies a higher height SDS is associated with a higher frequency of overweight/obesity. This is independent of the parameter used to evaluate overweight/obesity (BMI SDS or WC SDS).

  5. Spherical Harmonics Analysis of the ECMWF Global Wind Fields at the 10-Meter Height Level During 1985: A Collection of Figures Illustrating Results

    Science.gov (United States)

    Sanchez, Braulio V.; Nishihama, Masahiro

    1997-01-01

    Half-daily global wind speeds in the east-west (u) and north-south (v) directions at the 10-meter height level were obtained from the European Centre for Medium Range Weather Forecasts (ECMWF) data set of global analyses. The data set covered the period 1985 January to 1995 January. A spherical harmonic expansion to degree and order 50 was used to perform harmonic analysis of the east-west (u) and north-south (v) velocity field components. The resulting wind field is displayed, as well as the residual of the fit, at a particular time. The contribution of particular coefficients is shown. The time variability of the coefficients up to degree and order 3 is presented. Corresponding power spectrum plots are given. Time series analyses were applied also to the power associated with degrees 0-10; the results are included.

  6. Diurnal Evolution and Annual Variability of Boundary Layer Height in the Columbia River Gorge through the `Eye' of Wind Profiling Radars

    Science.gov (United States)

    Bianco, L.; Djalalova, I.; Konopleva-Akish, E.; Kenyon, J.; Olson, J. B.; Wilczak, J. M.

    2016-12-01

    The Second Wind Forecast Improvement Project (WFIP2) is a DoE- and NOAA-sponsored program whose goal is to improve the accuracy of numerical weather prediction (NWP) forecasts in complex terrain. WFIP2 consists of an 18-month (October 2015 - March 2017) field campaign held in the Columbia River basin, in the Pacific Northwest of the U.S. As part of WFIP2 a large suite of in-situ and remote sensing instrumentation has been deployed, including, among several others, a network of eight 915-MHz wind profiling radars (WPRs) equipped with radio acoustic sounding systems (RASSs), and many surface meteorological stations. The diurnal evolution and annual variability of boundary layer height in the area of WFIP2 will be investigated through the `eye' of WPRs, employing state-of-the-art automated algorithms, based on fuzzy logic and artificial intelligence. The results will be used to evaluate possible errors in NWP models in this area of complex terrain.

  7. Decadal variability of extreme wave height representing storm severity in the northeast Atlantic and North Sea since the foundation of the Royal Society

    Science.gov (United States)

    Santo, H.; Taylor, P. H.; Gibson, R.

    2016-09-01

    Long-term estimation of extreme wave height remains a key challenge because of the short duration of available wave data, and also because of the possible impact of climate variability on ocean waves. Here, we analyse storm-based statistics to obtain estimates of extreme wave height at locations in the northeast Atlantic and North Sea using the NORA10 wave hindcast (1958-2011), and use a 5 year sliding window to examine temporal variability. The decadal variability is correlated to the North Atlantic oscillation and other atmospheric modes, using a six-term predictor model incorporating the climate indices and their Hilbert transforms. This allows reconstruction of the historic extreme climate back to 1661, using a combination of known and proxy climate indices. Significant decadal variability primarily driven by the North Atlantic oscillation is observed, and this should be considered for the long-term survivability of offshore structures and marine renewable energy devices. The analysis on wave climate reconstruction reveals that the variation of the mean, 99th percentile and extreme wave climates over decadal time scales for locations close to the dominant storm tracks in the open North Atlantic are comparable, whereas the wave climates for the rest of the locations including the North Sea are rather different.

  8. Association between Adult Height and Risk of Colorectal, Lung, and Prostate Cancer : Results from Meta-analyses of Prospective Studies and Mendelian Randomization Analyses

    NARCIS (Netherlands)

    Khankari, Nikhil K.; Shu, Xiao Ou; Wen, Wanqing; Kraft, Peter; Lindström, Sara; Peters, Ulrike; Schildkraut, Joellen; Schumacher, Fredrick; Bofetta, Paolo; Risch, Angela; Bickeböller, Heike; Amos, Christopher I.; Easton, Douglas; Eeles, Rosalind A.; Gruber, Stephen B.; Haiman, Christopher A.; Hunter, David J.; Chanock, Stephen J.; Pierce, Brandon L.; Zheng, Wei; Blalock, Kendra; Campbell, Peter T.; Casey, Graham; Conti, David V.; Edlund, Christopher K.; Figueiredo, Jane; James Gauderman, W.; Gong, Jian; Green, Roger C.; Harju, John F.; Harrison, Tabitha A.; Jacobs, Eric J.; Jenkins, Mark A.; Jiao, Shuo; Li, Li; Lin, Yi; Manion, Frank J.; Moreno, Victor; Mukherjee, Bhramar; Raskin, Leon; Schumacher, Fredrick R.; Seminara, Daniela; Severi, Gianluca; Stenzel, Stephanie L.; Thomas, Duncan C.; Hopper, John L.; Southey, Melissa C.; Makalic, Enes; Schmidt, Daniel F.; Fletcher, Olivia; Peto, Julian; Gibson, Lorna; dos Santos Silva, Isabel; Ahsan, Habib; Whittemore, Alice; Waisfisz, Quinten; Meijers-Heijboer, Hanne; Adank, Muriel; van der Luijt, Rob B.; Uitterlinden, Andre G.; Hofman, Albert; Meindl, Alfons; Schmutzler, Rita K.; Müller-Myhsok, Bertram; Lichtner, Peter; Nevanlinna, Heli; Muranen, Taru A.; Aittomäki, Kristiina; Blomqvist, Carl; Chang-Claude, Jenny; Hein, Rebecca; Dahmen, Norbert; Beckman, Lars; Crisponi, Laura; Hall, Per; Czene, Kamila; Irwanto, Astrid; Liu, Jianjun; Easton, Douglas F.; Turnbull, Clare; Rahman, Nazneen; Eeles, Rosalind; Kote-Jarai, Zsofia; Muir, Kenneth; Giles, Graham; Neal, David; Donovan, Jenny L.; Hamdy, Freddie C.; Wiklund, Fredrik; Gronberg, Henrik; Haiman, Christopher; Schumacher, Fred; Travis, Ruth; Riboli, Elio; Hunter, David; Gapstur, Susan; Berndt, Sonja; Chanock, Stephen; Han, Younghun; Su, Li; Wei, Yongyue; Hung, Rayjean J.; Brhane, Yonathan; McLaughlin, John; Brennan, Paul; McKay, James D.; Rosenberger, Albert; Houlston, Richard S.; Caporaso, Neil; Teresa Landi, Maria; Heinrich, Joachim; Wu, Xifeng; Ye, Yuanqing; Christiani, David C.

    2016-01-01

    Background: Observational studies examining associations between adult height and risk of colorectal, prostate, and lung cancers have generated mixed results. We conducted meta-analyses using data from prospective cohort studies and further carried out Mendelian randomization analyses, using

  9. Chaos resulting from nonlinear relations between different variables

    International Nuclear Information System (INIS)

    Dohtani, Akitaka

    2011-01-01

    Research highlights: → We prove a general result on the existence of chaos. → We focus on the cyclic composites of interdependent relations between different variables. → By considering several examples, we conclude that the cyclic composites play an important role in detecting chaotic dynamics. - Abstract: In this study, we further develop the perturbation method of Marotto and investigate the general mechanisms responsible for nonlinear dynamics, which are typical of multidimensional systems. We focus on the composites of interdependent relations between different variables. First, we prove a general result on chaos, which shows that the cyclic composites of nonlinear interdependent relations are sources of chaotic dynamics in multidimensional systems. By considering several examples, we conclude that the cyclic composites play an important role in detecting chaotic dynamics.

  10. Results of two years of water training on jump height in postmenopausal women with moderate hip risk fracture

    Directory of Open Access Journals (Sweden)

    María Carrasco Poyatos

    2010-01-01

    Full Text Available The aim of the present study was to investigate the effect of a water-based calisthenics and resistance program on jump height in postmenopausal women with moderate hip risk fracture. 39 women were divided into three groups: swimming group (GN; n = 17, calisthenics and resistance group (GIR; n = 14, and control group (GC; n = 8. Body composition test included body mass index (IMC and waist to hip ratio (ICC. Jump height was assessed by a countermovement jump (CMJ. GN showed a significant (p<0.05 decrease in ICC (5.81%. GIR showed a significant decrease in IMC (3.65% and a significant increase in CMJ (15.5%. Two years of water-based calisthenics and resistance training can offer significant benefits in jump height in postmenopausal women with moderate hip risk fracture. Both exercise programs can also improve body composition.

  11. Initial CGE Model Results Summary Exogenous and Endogenous Variables Tests

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Brian Keith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boero, Riccardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rivera, Michael Kelly [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-07

    The following discussion presents initial results of tests of the most recent version of the National Infrastructure Simulation and Analysis Center Dynamic Computable General Equilibrium (CGE) model developed by Los Alamos National Laboratory (LANL). The intent of this is to test and assess the model’s behavioral properties. The test evaluated whether the predicted impacts are reasonable from a qualitative perspective. This issue is whether the predicted change, be it an increase or decrease in other model variables, is consistent with prior economic intuition and expectations about the predicted change. One of the purposes of this effort is to determine whether model changes are needed in order to improve its behavior qualitatively and quantitatively.

  12. Association between Adult Height and Risk of Colorectal, Lung, and Prostate Cancer: Results from Meta-analyses of Prospective Studies and Mendelian Randomization Analyses

    Science.gov (United States)

    Khankari, Nikhil K.; Shu, Xiao-Ou; Wen, Wanqing; Kraft, Peter; Lindström, Sara; Peters, Ulrike; Schildkraut, Joellen; Schumacher, Fredrick; Bofetta, Paolo; Risch, Angela; Bickeböller, Heike; Amos, Christopher I.; Easton, Douglas; Gruber, Stephen B.; Haiman, Christopher A.; Hunter, David J.; Chanock, Stephen J.; Pierce, Brandon L.; Zheng, Wei

    2016-01-01

    Background Observational studies examining associations between adult height and risk of colorectal, prostate, and lung cancers have generated mixed results. We conducted meta-analyses using data from prospective cohort studies and further carried out Mendelian randomization analyses, using height-associated genetic variants identified in a genome-wide association study (GWAS), to evaluate the association of adult height with these cancers. Methods and Findings A systematic review of prospective studies was conducted using the PubMed, Embase, and Web of Science databases. Using meta-analyses, results obtained from 62 studies were summarized for the association of a 10-cm increase in height with cancer risk. Mendelian randomization analyses were conducted using summary statistics obtained for 423 genetic variants identified from a recent GWAS of adult height and from a cancer genetics consortium study of multiple cancers that included 47,800 cases and 81,353 controls. For a 10-cm increase in height, the summary relative risks derived from the meta-analyses of prospective studies were 1.12 (95% CI 1.10, 1.15), 1.07 (95% CI 1.05, 1.10), and 1.06 (95% CI 1.02, 1.11) for colorectal, prostate, and lung cancers, respectively. Mendelian randomization analyses showed increased risks of colorectal (odds ratio [OR] = 1.58, 95% CI 1.14, 2.18) and lung cancer (OR = 1.10, 95% CI 1.00, 1.22) associated with each 10-cm increase in genetically predicted height. No association was observed for prostate cancer (OR = 1.03, 95% CI 0.92, 1.15). Our meta-analysis was limited to published studies. The sample size for the Mendelian randomization analysis of colorectal cancer was relatively small, thus affecting the precision of the point estimate. Conclusions Our study provides evidence for a potential causal association of adult height with the risk of colorectal and lung cancers and suggests that certain genetic factors and biological pathways affecting adult height may also affect the

  13. Wuthering Heights

    NARCIS (Netherlands)

    Bronte, Emily

    2005-01-01

    Wuthering Heights tells the story of a romance between two youngsters: Catherine Earnshaw and an orphan boy, Heathcliff. After she rejects him for a boy from a better background he develops a lust for revenge that takes over his life. In attempting to win her back and destroy those he blames for his

  14. Love and fear of heights: the pathophysiology and psychology of height imbalance.

    Science.gov (United States)

    Salassa, John R; Zapala, David A

    2009-01-01

    Individual psychological responses to heights vary on a continuum from acrophobia to height intolerance, height tolerance, and height enjoyment. This paper reviews the English literature and summarizes the physiologic and psychological factors that generate different responses to heights while standing still in a static or motionless environment. Perceptual cues to height arise from vision. Normal postural sway of 2 cm for peripheral objects within 3 m increases as eye-object distance increases. Postural sway >10 cm can result in a fall. A minimum of 20 minutes of peripheral retinal arc is required to detect motion. Trigonometry dictates that a 20-minute peripheral retinal arch can no longer be achieved in a standing position at an eye-object distance of >20 m. At this distance, visual cues conflict with somatosensory and vestibular inputs, resulting in variable degrees of imbalance. Co-occurring deficits in the visual, vestibular, and somatosensory systems can significantly increase height imbalance. An individual's psychological makeup, influenced by learned and genetic factors, can influence reactions to height imbalance. Enhancing peripheral vision and vestibular, proprioceptive, and haptic functions may improve height imbalance. Psychotherapy may improve the troubling subjective sensations to heights.

  15. Cataclysmic Variables from SDSS I. The First Results

    OpenAIRE

    Szkody, P.; Anderson, S. F.; Agueros, M.; Covarrubias, R.; Bentz, M.; Hawley, S.; Margon, B.; Voges, W.; Henden, A.; Knapp, G. R.; Berk, D. E. Vanden; Rest, A.; Miknaitis, G.; Magnier, E.; Brinkmann, J.

    2001-01-01

    The commissioning year of the Sloan Digital Sky Survey has demonstrated that many cataclysmic variables have been missed in previous surveys with brighter limits. We report the identification of 22 cataclysmic variables, of which 19 are new discoveries and 3 are known systems (SW UMa, BH Lyn and Vir4). A compendium of positions, colors and characteristics of these systems obtained from the SDSS photometry and spectroscopy is presented along with data obtained during follow-up studies with the...

  16. Intraspecific variability of European larch for wood properties: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Paques, L.E.; Rozenberg, P. [Institut National de Recherches Agronomiques (INRA), 45 - Olivet (France). Station d`Amelioration des Arbres Forestiers

    1995-12-31

    Wood properties of several natural populations of European larch (Larix decidua Mill) were determined from samples collected in one replicate of the II. International IUFRO provenance experiment, planted in Brittany in 1959. According to provenances, proportion of heartwood ranges from 35 to 58% of basal area, basic density from 442 to 505 g/dm{sup 3} and Young modulus of elasticity from 8474 to 14522 MPa. Positive correlations between girth and heartwood proportion and between wood density and modulus of elasticity but negative correlations between ring width and both density and MOE have been found both at the individual and at the population levels. Variability between and within provenances is high for two major traits (proportion of heartwood and Young modulus of elasticity) for which a SW - NE gradient is shown. For wood density parameters including pilodyn, a greater homogeneity is observed. Besides a now largely recognized superiority for growth traits, Central European populations from the Sudetan Mountains and Central Poland would also produce wood with better properties. On the reverse, Alpine populations from the French Alps growing at low elevations have a slower growth, a denser wood with less heartwood and less strength. Used as a control, the hybrid larch origin (Larix x eurolepis) represents the best compromise for wood properties with the highest strength but an average wood density and one of the highest proportion of heartwood. These preliminary results must be confirmed from a larger set of provenances and completed with other major wood properties such as durability and shrinkage. 17 refs, 2 figs, 6 tabs

  17. Intraspecific variability of European larch for wood properties: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Paques, L E; Rozenberg, P [Institut National de Recherches Agronomiques (INRA), 45 - Olivet (France). Station d` Amelioration des Arbres Forestiers

    1996-12-31

    Wood properties of several natural populations of European larch (Larix decidua Mill) were determined from samples collected in one replicate of the II. International IUFRO provenance experiment, planted in Brittany in 1959. According to provenances, proportion of heartwood ranges from 35 to 58% of basal area, basic density from 442 to 505 g/dm{sup 3} and Young modulus of elasticity from 8474 to 14522 MPa. Positive correlations between girth and heartwood proportion and between wood density and modulus of elasticity but negative correlations between ring width and both density and MOE have been found both at the individual and at the population levels. Variability between and within provenances is high for two major traits (proportion of heartwood and Young modulus of elasticity) for which a SW - NE gradient is shown. For wood density parameters including pilodyn, a greater homogeneity is observed. Besides a now largely recognized superiority for growth traits, Central European populations from the Sudetan Mountains and Central Poland would also produce wood with better properties. On the reverse, Alpine populations from the French Alps growing at low elevations have a slower growth, a denser wood with less heartwood and less strength. Used as a control, the hybrid larch origin (Larix x eurolepis) represents the best compromise for wood properties with the highest strength but an average wood density and one of the highest proportion of heartwood. These preliminary results must be confirmed from a larger set of provenances and completed with other major wood properties such as durability and shrinkage. 17 refs, 2 figs, 6 tabs

  18. Assessing variability in results in systematic reviews of diagnostic studies

    NARCIS (Netherlands)

    Naaktgeboren, Christiana A; Ochodo, Eleanor A; Van Enst, Wynanda A; de Groot, Joris A H; Hooft, Lotty; Leeflang, Mariska M G; Bossuyt, Patrick M; Moons, Karel G M; Reitsma, Johannes B

    2016-01-01

    BACKGROUND: To describe approaches used in systematic reviews of diagnostic test accuracy studies for assessing variability in estimates of accuracy between studies and to provide guidance in this area. METHODS: Meta-analyses of diagnostic test accuracy studies published between May and September

  19. Variable features on Mars - Preliminary Mariner 9 television results.

    Science.gov (United States)

    Sagan, C.; Veverka, J.; Fox, P.; Dubisch, R.; Lederberg, J.; Levinthal, E.; Quam, L.; Tucker, R.; Pollack, J. B.; Smith, B. A.

    1972-01-01

    Systematic Mariner 9 photography of a range of Martian surface features, observed with all three photometric angles approximately invariant, reveals three general categories of albedo variations: (1) an essentially uniform contrast enhancement due to the dissipation of the dust storm; (2) the appearance of splotches, irregular dark markings at least partially related to topography; and (3) the development of both bright and dark linear streaks, generally emanating from craters. Some splotches and streaks vary on characteristic timescales of about two weeks; they have characteristic dimensions of kilometers to tens of kilometers. The morphology and variability of streaks and splotches, and the resolution of at least one splotch into an extensive dune system, implicate windblown dust as the principal agent of Martian albedo differences and variability.

  20. Understanding the Steric Height Long Term Variability at the Bermuda Atlantic Time-Series Study (BATS) Site with a Neutral Density Approach

    Science.gov (United States)

    Goncalves Neto, A.; Johnson, R. J.; Bates, N. R.

    2016-02-01

    Rising sea level is one of the main concerns for human life in a scenario with global atmosphere and ocean warming, which is of particular concern for oceanic islands. Bermuda, located in the center of the Sargasso Sea, provides an ideal location to investigate sea level rise since it has a long term tide gauge (1933-present) and is in close proximity to deep ocean time-series sites, namely, Hydrostation `S' (1954-present) and the Bermuda Atlantic Time-Series Study site (1988-present). In this study, we use the monthly CTD deep casts at BATS to compute the contribution of steric height (SH) to the local sea surface height (SSH) for the past 24 years. To determine the relative contribution from the various water masses we first define 8 layers (Surface Layer, Upper Thermocline, Subtropical Mode-Water, Lower Thermocline, Antarctic Intermediate Water, Labrador Sea Water, Iceland-Scotland Overflow Water, Denmark Strait Overflow Water) based on neutral density criteria for which SH is computed. Additionally, we calculate the thermosteric and halosteric components for each of the defined neutral density layers. Surprisingly, the results show that, despite a 3.3mm/yr sea level rise observed at the Bermuda tide gauge, the steric contribution to the SSH at BATS has decreased at a rate of -1.1mm/yr during the same period. The thermal component is found to account for the negative trend in the steric height (-4.4mm/yr), whereas the halosteric component (3.3mm/yr) partially compensates the thermal signal and can be explained by an overall cooling and freshening at the BATS site. Although the surface layer and the upper thermocline waters are warming, all the subtropical and polar water masses, which represent most of the local water column, are cooling and therefore drive the overall SH contribution to the local SSH. Hence, it suggests that the mass contribution to the local SSH plays an important role in the sea level rise, for which we investigate with GRACE data.

  1. The GRB variability/peak luminosity correlation: new results

    International Nuclear Information System (INIS)

    Guidorzi, C.; Rossi, F.; Hurley, K.; Mundell, C.G.

    2005-01-01

    We test the correlation between time variability and isotropic-equivalent peak luminosity found by Reichart et al. (ApJ, 552 (2001) 57) using a set of 26 Gamma-Ray Bursts (GRBs) with known redshift. We confirm the correlation, thought with a larger spread around the best-fit power-law obtained by Reichart et al. which in turn does not provide an acceptable description any longer. In addiction, we find no evidence for correlation between variability and beaming-corrected peak luminosity for a subset of 14 GRBs whose beaming angles have been taken from Ghirlanda et al. (ApJ, 616 (2004) 331). Finally, we investigate the possible connection for some GRBs between the location in the variability/peak luminosity space and some afterglow properties, such as the detectability in the optical band, by adding some GRBs whose redshifts, unknown from direct measurements, have been derived assuming the Amati at al. (AeA, 390 (2002) 81) relationship

  2. Childhood height, adult height, and the risk of prostate cancer

    DEFF Research Database (Denmark)

    Bjerregaard, Lise Geisler; Aarestrup, Julie; Gamborg, Michael

    2016-01-01

    PURPOSE: We previously showed that childhood height is positively associated with prostate cancer risk. It is, however, unknown whether childhood height exerts its effects independently of or through adult height. We investigated whether and to what extent childhood height has a direct effect...... on the risk of prostate cancer apart from adult height. METHODS: We included 5,871 men with height measured at ages 7 and 13 years in the Copenhagen School Health Records Register who also had adult (50-65 years) height measured in the Danish Diet, Cancer and Health study. Prostate cancer status was obtained...... through linkage to the Danish Cancer Registry. Direct and total effects of childhood height on prostate cancer risk were estimated from Cox regressions. RESULTS: From 1996 to 2012, 429 prostate cancers occurred. Child and adult heights were positively and significantly associated with prostate cancer risk...

  3. Preliminary results of variable star search using KMTNet data

    Directory of Open Access Journals (Sweden)

    Jeon Young-Beom

    2017-01-01

    Full Text Available The KMTNet (Korea Microlensing Telescope Network was completed on October 2nd in 2015. There are three 1.6 m telescopes in Chile (CTIO, Australia (SSO and South Africa (SAAO. The field of view of the CCD camera is 2 degree × 2 degree. We are monitoring and observing the bulge region for 24-hour continuous observations using the KMTNet telescopes. I present the characteristics of CCD camera and telescope, and the status of observation programs. We are still developing CCD cameras to accurate photometry. From the KMTNet data, we can obtain accurate 24-hour continuous time-series data for many variable stars.

  4. Variability in the maximum height of the ionospheric F2-layer over Millstone Hill (September 1998–March 2000; influence from below and above

    Directory of Open Access Journals (Sweden)

    D. Pancheva

    2002-11-01

    Full Text Available The basic aim of this ‘case study’ is to investigate the variability in the maximum height of the ionospheric F2-layer, hmF2, with periods of planetary waves (2–30 days, and to make an attempt to determine their origin. The hourly data of hmF2 above Millstone Hill (42.6° N, 71.5° W during 01 September 1998 - 31 March 2000 were used for analysis. Three types of disturbances are studied in detail: (i the 27- day oscillations observed in the hmF2 above Millstone Hill are generated by the geomagnetic activity and by the global-scale 27-day wave present in the zonal mesosphere/lower thermosphere (MLT neutral wind. The time delay between the 27-day oscillation in the zonal wind and that in the hmF2 is found to be 5–6 days, while between the 27-day oscillation in the geomagnetic activity and that in the hmF2 is found to be 0.8–1 day; (ii the 16-day oscillation in the hmF2 observed during summer 1999 is probably generated by the global scale 16-day modulation of the semidiurnal tide observed in the MLT region during PSMOS campaign in June–August. We found that if the modulated semidiurnal tide mediates the planetary wave signature in the ionosphere, this planetary wave oscillation has to be best expressed in the amplitude and in the phase of the 12-h periodicity of the ionosphere; and (iii the third type of disturbances studied is the quasi-2- day activity in the hmF2 that increases during geomagnetic disturbances. The strong pseudo diurnal periodicities generated during the geomagnetic storms can interact between each other and produce the quasi-2-day oscillations in the ionosphere.Key words. Ionosphere (ionosphere-atmosphere interactions; ionosphere-magnetoshpere interactions; wave propagation

  5. Memory for target height is scaled to observer height.

    Science.gov (United States)

    Twedt, Elyssa; Crawford, L Elizabeth; Proffitt, Dennis R

    2012-04-01

    According to the embodied approach to visual perception, individuals scale the environment to their bodies. This approach highlights the central role of the body for immediate, situated action. The present experiments addressed whether body scaling--specifically, eye-height scaling--occurs in memory when action is not immediate. Participants viewed standard targets that were either the same height as, taller than, or shorter than themselves. Participants then viewed a comparison target and judged whether the comparison was taller or shorter than the standard target. Participants were most accurate when the standard target height matched their own heights, taking into account postural changes. Participants were biased to underestimate standard target height, in general, and to push standard target height away from their own heights. These results are consistent with the literature on eye-height scaling in visual perception and suggest that body scaling is not only a useful metric for perception and action, but is also preserved in memory.

  6. INFLUENCE OF BODY HEIGHT, BODY WEIGHT AND THE AGE ON THE RESULTS ACHIEVED BY MAN-MARATHONERS IN A MARATHON RACE

    OpenAIRE

    Naser Rašiti Naser; Vlora Ajvazi; Adem Nura; Halim Hajredini

    2011-01-01

    The research is conducted on a sample of 100 successful man marathoners who has taken part in ten of the most popular marathon races. The sample of entities includes ten of the best placed marathoners in each race held during the year 2008. The aim of the research is to assess the influence of the body height, weight and the age of the marathoners on the final result in the race. The collected data is processed by the basic descriptive parameters. The entities have the average weight of 56.94...

  7. Height premium for job performance.

    Science.gov (United States)

    Kim, Tae Hyun; Han, Euna

    2017-08-01

    This study assessed the relationship of height with wages, using the 1998 and 2012 Korean Labor and Income Panel Study data. The key independent variable was height measured in centimeters, which was included as a series of dummy indicators of height per 5cm span (wages to assess the heterogeneity in the height-wage relationship, across the conditional distribution of monthly wages. We found a non-linear relationship of height with monthly wages. For men, the magnitude of the height wage premium was overall larger at the upper quantile of the conditional distribution of log monthly wages than at the median to low quantile, particularly in professional and semi-professional occupations. The height-wage premium was also larger at the 90th quantile for self-employed women and salaried men. Our findings add a global dimension to the existing evidence on height-wage premium, demonstrating non-linearity in the association between height and wages and heterogeneous changes in the dispersion and direction of the association between height and wages, by wage level. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Encounter Probability of Significant Wave Height

    DEFF Research Database (Denmark)

    Liu, Z.; Burcharth, H. F.

    The determination of the design wave height (often given as the significant wave height) is usually based on statistical analysis of long-term extreme wave height measurement or hindcast. The result of such extreme wave height analysis is often given as the design wave height corresponding to a c...

  9. The effect of female height on reproductive success is negative in Western populations, but more variable in non-Western populations

    NARCIS (Netherlands)

    Stulp, G.; Verhulst, S.; Pollet, T.V.; Buunk, A.P.

    2012-01-01

    Objective: In this article we examine the association between female height and reproductive success in a US sample and present a review of previous studies on this association. We also outline possible biological explanations for our findings. Methods: We used data from a long-term study of 5,326

  10. Improved boundary layer height measurement using a fuzzy logic method: Diurnal and seasonal variabilities of the convective boundary layer over a tropical station

    Science.gov (United States)

    Allabakash, S.; Yasodha, P.; Bianco, L.; Venkatramana Reddy, S.; Srinivasulu, P.; Lim, S.

    2017-09-01

    This paper presents the efficacy of a "tuned" fuzzy logic method at determining the height of the boundary layer using the measurements from a 1280 MHz lower atmospheric radar wind profiler located in Gadanki (13.5°N, 79°E, 375 mean sea level), India, and discusses the diurnal and seasonal variations of the measured convective boundary layer over this tropical station. The original fuzzy logic (FL) method estimates the height of the atmospheric boundary layer combining the information from the range-corrected signal-to-noise ratio, the Doppler spectral width of the vertical velocity, and the vertical velocity itself, measured by the radar, through a series of thresholds and rules, which did not prove to be optimal for our radar system and geographical location. For this reason the algorithm was tuned to perform better on our data set. Atmospheric boundary layer heights obtained by this tuned FL method, the original FL method, and by a "standard method" (that only uses the information from the range-corrected signal-to-noise ratio) are compared with those obtained from potential temperature profiles measured by collocated Global Positioning System Radio Sonde during years 2011 and 2013. The comparison shows that the tuned FL method is more accurate than the other methods. Maximum convective boundary layer heights are observed between 14:00 and 15:00 local time (LT = UTC + 5:30) for clear-sky days. These daily maxima are found to be lower during winter and postmonsoon seasons and higher during premonsoon and monsoon seasons, due to net surface radiation and convective processes over this region being more intense during premonsoon and monsoon seasons and less intense in winter and postmonsoon seasons.

  11. Estimation of genetic variability and heritability of wheat agronomic traits resulted from some gamma rays irradiation techniques

    International Nuclear Information System (INIS)

    Wijaya Murti Indriatama; Trikoesoemaningtyas; Syarifah Iis Aisyah; Soeranto Human

    2016-01-01

    Gamma irradiation techniques have significant effect on frequency and spectrum of macro-mutation but the study of its effect on micro-mutation that related to genetic variability on mutated population is very limited. The aim of this research was to study the effect of gamma irradiation techniques on genetic variability and heritability of wheat agronomic characters at M2 generation. This research was conducted from July to November 2014, at Cibadak experimental station, Indonesian Center for Agricultural Biotechnology and Genetic Resources Research and Development, Ministry of Agriculture. Three introduced wheat breeding lines (F-44, Kiran-95 & WL-711) were treated by 3 gamma irradiation techniques (acute, fractionated and intermittent). M1 generation of combination treatments were planted and harvested its spike individually per plants. As M2 generation, seeds of 75 M1 spike were planted at the field with one row one spike method and evaluated on the agronomic characters and its genetic components. The used of gamma irradiation techniques decreased mean but increased range values of agronomic traits in M2 populations. Fractionated irradiation induced higher mean and wider range on spike length and number of spike let per spike than other irradiation techniques. Fractionated and intermittent irradiation resulted greater variability of grain weight per plant than acute irradiation. The number of tillers, spike weight, grain weight per spike and grain weight per plant on M2 population resulted from induction of three gamma irradiation techniques have high estimated heritability and broad sense of genetic variability coefficient values. The three gamma irradiation techniques increased genetic variability of agronomic traits on M2 populations, except plant height. (author)

  12. Development and evaluation of height diameter at breast models for native Chinese Metasequoia.

    Science.gov (United States)

    Liu, Mu; Feng, Zhongke; Zhang, Zhixiang; Ma, Chenghui; Wang, Mingming; Lian, Bo-Ling; Sun, Renjie; Zhang, Li

    2017-01-01

    Accurate tree height and diameter at breast height (dbh) are important input variables for growth and yield models. A total of 5503 Chinese Metasequoia trees were used in this study. We studied 53 fitted models, of which 7 were linear models and 46 were non-linear models. These models were divided into two groups of single models and multivariate models according to the number of independent variables. The results show that the allometry equation of tree height which has diameter at breast height as independent variable can better reflect the change of tree height; in addition the prediction accuracy of the multivariate composite models is higher than that of the single variable models. Although tree age is not the most important variable in the study of the relationship between tree height and dbh, the consideration of tree age when choosing models and parameters in model selection can make the prediction of tree height more accurate. The amount of data is also an important parameter what can improve the reliability of models. Other variables such as tree height, main dbh and altitude, etc can also affect models. In this study, the method of developing the recommended models for predicting the tree height of native Metasequoias aged 50-485 years is statistically reliable and can be used for reference in predicting the growth and production of mature native Metasequoia.

  13. Development and evaluation of height diameter at breast models for native Chinese Metasequoia.

    Directory of Open Access Journals (Sweden)

    Mu Liu

    Full Text Available Accurate tree height and diameter at breast height (dbh are important input variables for growth and yield models. A total of 5503 Chinese Metasequoia trees were used in this study. We studied 53 fitted models, of which 7 were linear models and 46 were non-linear models. These models were divided into two groups of single models and multivariate models according to the number of independent variables. The results show that the allometry equation of tree height which has diameter at breast height as independent variable can better reflect the change of tree height; in addition the prediction accuracy of the multivariate composite models is higher than that of the single variable models. Although tree age is not the most important variable in the study of the relationship between tree height and dbh, the consideration of tree age when choosing models and parameters in model selection can make the prediction of tree height more accurate. The amount of data is also an important parameter what can improve the reliability of models. Other variables such as tree height, main dbh and altitude, etc can also affect models. In this study, the method of developing the recommended models for predicting the tree height of native Metasequoias aged 50-485 years is statistically reliable and can be used for reference in predicting the growth and production of mature native Metasequoia.

  14. (001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni2Si formation and the resulting barrier height changes

    Science.gov (United States)

    Tengeler, Sven; Kaiser, Bernhard; Chaussende, Didier; Jaegermann, Wolfram

    2017-04-01

    The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni2Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

  15. SPES-2, the full-height, full-pressure, test facility simulating the AP600 plant: Main results from the experimental campaign

    International Nuclear Information System (INIS)

    Medich, C.; Rigamonti, M.; Martinelli, R.; Tarantini, M.; Conway, L.

    1995-01-01

    The SPES-2 is a full height, full pressure experimental test facility reproducing the Westinghouse AP600 reactor with a scaling factor of 1/395. The experimental plant, designed and operated by SIET in Piacenza, consists of a full simulation of the AP600 primary core cooling system including all the passive and active safety systems. In 1992, Westinghouse, in cooperation with ENEL, ENEA, SIET and ANSALDO developed an experimental program to test the integrated behavior of the AP600 passive safety systems. The SPES-2 test matrix, concluded in November 1994, has examined the AP600 passive safety system response for a range of small break LOCAs at different locations on the primary system and on the passive system lines; single steam generator tube ruptures with both passive and active non-safety systems, and a main steam line break transient to demonstrate the capability of passive safety systems for rapid cooldown. Each of the tests has provided detailed experimental results for verification of the capability of the analysis methods to predict the integrated passive safety system behavior

  16. Fear of heights and visual height intolerance.

    Science.gov (United States)

    Brandt, Thomas; Huppert, Doreen

    2014-02-01

    The aim of this review is, first, to cover the different aspects of visual height intolerance such as historical descriptions, definition of terms, phenomenology of the condition, neurophysiological control of gaze, stance and locomotion, and therapy, and, second, to identify warranted epidemiological and experimental studies. Vivid descriptions of fear of heights can be found in ancient texts from the Greek, Roman, and Chinese classics. The life-time prevalence of visual height intolerance is as high as 28% in the general population, and about 50% of those who are susceptible report an impact on quality of life. When exposed to heights, visual exploration by eye and head movements is restricted, and the velocity of locomotion is reduced. Therapy for fear of heights is dominated by the behavioral techniques applied during real or virtual reality exposure. Their efficacy might be facilitated by the administration of D-cycloserine or glucocorticoids. Visual height intolerance has a considerable impact on daily life and interpersonal interactions. It is much more frequent than fear of heights, which is defined as an environmental subtype of a specific phobia. There is certainly a continuum stretching from acrophobia to a less-pronounced visual height intolerance, to which the categorical distinction of a specific phobia does not apply.

  17. Prevalence of overweight and obesity on the island of Ireland: results from the North South Survey of Children's Height, Weight and Body Mass Index, 2002.

    LENUS (Irish Health Repository)

    Whelton, Helen

    2007-01-01

    BACKGROUND: Childhood obesity is emerging as a major public health problem in developed and developing countries worldwide. The aim of this survey was to establish baseline data on the prevalence and correlates of overweight and obesity among children and adolescents in the Republic of Ireland (RoI) and Northern Ireland (NI). METHODS: The heights and weights of 19,617 school-going children and adolescents aged between 4 and 16 years in NI and RoI were measured using standardised and calibrated scales and measures. The participants were a representative cross-sectional sample of children randomly selected on the basis of age, gender and geographical location of the school attended. Overweight and obesity were classified according to standard IOTF criteria. RESULTS: Males were taller than females, children in RoI were taller than those in NI and the more affluent were taller than the less well off. The overall prevalence of overweight and obesity was higher among females than males in both jurisdictions. Overall, almost one in four boys (23% RoI and NI) and over one in four girls (28% RoI, 25% NI) were either overweight or obese. In RoI, the highest prevalence of overweight was among 13 year old girls (32%) and obesity among 7 year old girls (11%). In NI the highest prevalence of overweight and obesity were found among 11 and 8 year old girls respectively (33% and 13%). CONCLUSION: These figures confirm the emergence of the obesity epidemic among children in Ireland, a wealthy country with the European Union. The results serve to underpin the urgency of implementing broad intersectoral measures to reduce calorie intake and increase levels of physical activity, particularly among children.

  18. Prevalence of overweight and obesity on the island of Ireland: results from the North South Survey of Children's Height, Weight and Body Mass Index, 2002

    Directory of Open Access Journals (Sweden)

    Kelleher Virginia

    2007-07-01

    Full Text Available Abstract Background Childhood obesity is emerging as a major public health problem in developed and developing countries worldwide. The aim of this survey was to establish baseline data on the prevalence and correlates of overweight and obesity among children and adolescents in the Republic of Ireland (RoI and Northern Ireland (NI. Methods The heights and weights of 19,617 school-going children and adolescents aged between 4 and 16 years in NI and RoI were measured using standardised and calibrated scales and measures. The participants were a representative cross-sectional sample of children randomly selected on the basis of age, gender and geographical location of the school attended. Overweight and obesity were classified according to standard IOTF criteria. Results Males were taller than females, children in RoI were taller than those in NI and the more affluent were taller than the less well off. The overall prevalence of overweight and obesity was higher among females than males in both jurisdictions. Overall, almost one in four boys (23% RoI and NI and over one in four girls (28% RoI, 25% NI were either overweight or obese. In RoI, the highest prevalence of overweight was among 13 year old girls (32% and obesity among 7 year old girls (11%. In NI the highest prevalence of overweight and obesity were found among 11 and 8 year old girls respectively (33% and 13%. Conclusion These figures confirm the emergence of the obesity epidemic among children in Ireland, a wealthy country with the European Union. The results serve to underpin the urgency of implementing broad intersectoral measures to reduce calorie intake and increase levels of physical activity, particularly among children.

  19. (001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni{sub 2}Si formation and the resulting barrier height changes

    Energy Technology Data Exchange (ETDEWEB)

    Tengeler, Sven, E-mail: stengeler@surface.tu-darmstadt.de [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Univ. Grenoble Alpes, CNRS, LMGP, F-38000 Grenoble (France); Kaiser, Bernhard [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Chaussende, Didier [Univ. Grenoble Alpes, CNRS, LMGP, F-38000 Grenoble (France); Jaegermann, Wolfram [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany)

    2017-04-01

    Highlights: • Schottky behavior (Φ{sub B} = 0.41 eV) and Fermi level pining were found pre annealing. • Ni{sub 2}Si formation was confirmed for 5 min at 850 °C. • 3C/Ni{sub 2}Si Fermi level alignment is responsible for ohmic contact behavior. • Wet chemical etching (Si–OH/C–H termination) does not impair Ni{sub 2}Si formation. - Abstract: The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni{sub 2}Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

  20. (001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni_2Si formation and the resulting barrier height changes

    International Nuclear Information System (INIS)

    Tengeler, Sven; Kaiser, Bernhard; Chaussende, Didier; Jaegermann, Wolfram

    2017-01-01

    Highlights: • Schottky behavior (Φ_B = 0.41 eV) and Fermi level pining were found pre annealing. • Ni_2Si formation was confirmed for 5 min at 850 °C. • 3C/Ni_2Si Fermi level alignment is responsible for ohmic contact behavior. • Wet chemical etching (Si–OH/C–H termination) does not impair Ni_2Si formation. - Abstract: The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni_2Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

  1. National evaluation of strategies to reduce safety violations for working from heights in construction companies: results from a randomized controlled trial

    NARCIS (Netherlands)

    van der Molen, Henk F.; den Herder, Aalt; Warning, Jan; Frings-Dresen, Monique H. W.

    2016-01-01

    The objective of this study is to evaluate the effectiveness of a face-to-face strategy and a direct mail strategy on safety violations while working from heights among construction companies compared to a control condition. Construction companies with workers at risk for fall injuries were eligible

  2. Does sitting height ratio affect estimates of obesity prevalence among Canadian Inuit? Results from the 2007-2008 Inuit Health Survey.

    Science.gov (United States)

    Galloway, Tracey; Chateau-Degat, Marie-Ludivine; Egeland, Grace M; Young, T Kue

    2011-01-01

    High sitting height ratio (SHR) is a characteristic commonly associated with Inuit morphology. Inuit are described as having short leg lengths and high trunk-to-stature proportions such that cutoffs for obesity derived from European populations may not adequately describe thresholds of disease risk. Further, high SHR may help explain the reduced impact of BMI on metabolic risk factors among Inuit relative to comparison populations. This study investigates the relationship between SHR and body mass index (BMI) in Inuit. Subjects are 2,168 individuals (837 males and 1,331 females) from 36 Inuit communities in the Canadian Arctic. Mean age is 42.63 ± 14.86 years in males and 41.71 ± 14.83 years in females. We use linear regression to examine the association between age, sex, height, sitting height, SHR, waist circumference (WC), and BMI. We then evaluate the efficacy of the relative sitting height adjustment as a method of correcting observed BMI to a population-standardized SHR. Mean BMI is significantly higher than among non-Inuit Canadians. Obesity prevalence is high, particularly among Inuit women. In the regression, only age and WC are significant predictors of BMI. While SHR is significantly greater than that of the US population, there is substantial agreement between overweight and obesity prevalence using observed and corrected BMI. We find no consistent relationship between SHR and BMI and suggest the unique anthropometric and metabolic profile observed in Inuit arise from factors not yet delineated. More complex anthropometric and imaging studies in Inuit are needed. Copyright © 2011 Wiley-Liss, Inc.

  3. Fall from heights: does height really matter?

    Science.gov (United States)

    Alizo, G; Sciarretta, J D; Gibson, S; Muertos, K; Romano, A; Davis, J; Pepe, A

    2018-06-01

    Fall from heights is high energy injuries and constitutes a fraction of all fall-related trauma evaluations while bearing an increase in morbidity and mortality. We hypothesize that despite advancements in trauma care, the overall survivability has not improved in this subset of trauma patients. All adult trauma patients treated after sustaining a fall from heights during a 40-month period were retrospectively reviewed. Admission demographics, clinical data, fall height (ft), injury patterns, ISS, GCS, length of stay, and mortality were reviewed. 116 patients sustained a fall from heights, 90.4% accidental. A mean age of 37± 14.7 years, 86% male, and a fall height of 19 ± 10 ft were encountered. Admission GCS was 13 ± 2 with ISS 10 ± 11. Overall LOS was 6.6 ± 14.9 days and an ICU LOS of 2.8 ± 8.9 days. Falls ≥ 25 ft.(16%) had lower GCS 10.4 ± 5.8, increased ISS 22.6 ± 13.8, a fall height 37.9 ± 13.1 ft and associated increased mortality (p < 0.001). Mortality was 5.2%, a mean distance fallen of 39 ± 22 ft. and an ISS of 31.5 ±16.5. Brain injury was the leading cause of death, 50% with open skull fractures. Level of height fallen is a good predictor of overall outcome and survival. Despite advances in trauma care, death rates remain unchanged. Safety awareness and injury prevention programs are needed to reduce the risk of high-level falls.

  4. New Results On the Sum of Two Generalized Gaussian Random Variables

    KAUST Repository

    Soury, Hamza

    2015-01-01

    We propose in this paper a new method to compute the characteristic function (CF) of generalized Gaussian (GG) random variable in terms of the Fox H function. The CF of the sum of two independent GG random variables is then deduced. Based on this results, the probability density function (PDF) and the cumulative distribution function (CDF) of the sum distribution are obtained. These functions are expressed in terms of the bivariate Fox H function. Next, the statistics of the distribution of the sum, such as the moments, the cumulant, and the kurtosis, are analyzed and computed. Due to the complexity of bivariate Fox H function, a solution to reduce such complexity is to approximate the sum of two independent GG random variables by one GG random variable with suitable shape factor. The approximation method depends on the utility of the system so three methods of estimate the shape factor are studied and presented.

  5. New Results on the Sum of Two Generalized Gaussian Random Variables

    KAUST Repository

    Soury, Hamza

    2016-01-06

    We propose in this paper a new method to compute the characteristic function (CF) of generalized Gaussian (GG) random variable in terms of the Fox H function. The CF of the sum of two independent GG random variables is then deduced. Based on this results, the probability density function (PDF) and the cumulative distribution function (CDF) of the sum distribution are obtained. These functions are expressed in terms of the bivariate Fox H function. Next, the statistics of the distribution of the sum, such as the moments, the cumulant, and the kurtosis, are analyzed and computed. Due to the complexity of bivariate Fox H function, a solution to reduce such complexity is to approximate the sum of two independent GG random variables by one GG random variable with suitable shape factor. The approximation method depends on the utility of the system so three methods of estimate the shape factor are studied and presented [1].

  6. New Results on the Sum of Two Generalized Gaussian Random Variables

    KAUST Repository

    Soury, Hamza; Alouini, Mohamed-Slim

    2016-01-01

    We propose in this paper a new method to compute the characteristic function (CF) of generalized Gaussian (GG) random variable in terms of the Fox H function. The CF of the sum of two independent GG random variables is then deduced. Based on this results, the probability density function (PDF) and the cumulative distribution function (CDF) of the sum distribution are obtained. These functions are expressed in terms of the bivariate Fox H function. Next, the statistics of the distribution of the sum, such as the moments, the cumulant, and the kurtosis, are analyzed and computed. Due to the complexity of bivariate Fox H function, a solution to reduce such complexity is to approximate the sum of two independent GG random variables by one GG random variable with suitable shape factor. The approximation method depends on the utility of the system so three methods of estimate the shape factor are studied and presented [1].

  7. Evolutionary perspectives on human height variation

    NARCIS (Netherlands)

    Stulp, Gert; Barrett, Louise

    Human height is a highly variable trait, both within and between populations, has a high heritability, and influences the manner in which people behave and are treated in society. Although we know much about human height, this information has rarely been brought together in a comprehensive,

  8. Increased variability of bone tissue mineral density resulting from estrogen deficiency influences creep behavior in a rat vertebral body.

    Science.gov (United States)

    Kim, Do-Gyoon; Navalgund, Anand R; Tee, Boon Ching; Noble, Garrett J; Hart, Richard T; Lee, Hye Ri

    2012-11-01

    Progressive vertebral deformation increases the fracture risk of a vertebral body in the postmenopausal patient. Many studies have observed that bone can demonstrate creep behavior, defined as continued time-dependent deformation even when mechanical loading is held constant. Creep is a characteristic of viscoelastic behavior, which is common in biological materials. We hypothesized that estrogen deficiency-dependent alteration of the mineral distribution of bone at the tissue level could influence the progressive postmenopausal vertebral deformity that is observed as the creep response at the organ level. The objective of this study was thus to examine whether the creep behavior of vertebral bone is changed by estrogen deficiency, and to determine which bone property parameters are responsible for the creep response of vertebral bone at physiological loading levels using an ovariectomized (OVX) rat model. Correlations of creep parameters with bone mineral density (BMD), tissue mineral density (TMD) and architectural parameters of both OVX and sham surgery vertebral bone were tested. As the vertebral creep was not fully recovered during the post-creep unloading period, there was substantial residual displacement for both the sham and OVX groups. A strong positive correlation between loading creep and residual displacement was found (r=0.868, pcreep behavior of the OVX group (pcreep caused progressive, permanent reduction in vertebral height for both the sham and OVX groups. In addition, estrogen deficiency-induced active bone remodeling increased variability of trabecular TMD in the OVX group. Taken together, these results suggest that increased variability of trabecular TMD resulting from high bone turnover influences creep behavior of the OVX vertebrae. Copyright © 2012 Elsevier Inc. All rights reserved.

  9. Exact statistical results for binary mixing and reaction in variable density turbulence

    Science.gov (United States)

    Ristorcelli, J. R.

    2017-02-01

    We report a number of rigorous statistical results on binary active scalar mixing in variable density turbulence. The study is motivated by mixing between pure fluids with very different densities and whose density intensity is of order unity. Our primary focus is the derivation of exact mathematical results for mixing in variable density turbulence and we do point out the potential fields of application of the results. A binary one step reaction is invoked to derive a metric to asses the state of mixing. The mean reaction rate in variable density turbulent mixing can be expressed, in closed form, using the first order Favre mean variables and the Reynolds averaged density variance, ⟨ρ2⟩ . We show that the normalized density variance, ⟨ρ2⟩ , reflects the reduction of the reaction due to mixing and is a mix metric. The result is mathematically rigorous. The result is the variable density analog, the normalized mass fraction variance ⟨c2⟩ used in constant density turbulent mixing. As a consequence, we demonstrate that use of the analogous normalized Favre variance of the mass fraction, c″ ⁣2˜ , as a mix metric is not theoretically justified in variable density turbulence. We additionally derive expressions relating various second order moments of the mass fraction, specific volume, and density fields. The central role of the density specific volume covariance ⟨ρ v ⟩ is highlighted; it is a key quantity with considerable dynamical significance linking various second order statistics. For laboratory experiments, we have developed exact relations between the Reynolds scalar variance ⟨c2⟩ its Favre analog c″ ⁣2˜ , and various second moments including ⟨ρ v ⟩ . For moment closure models that evolve ⟨ρ v ⟩ and not ⟨ρ2⟩ , we provide a novel expression for ⟨ρ2⟩ in terms of a rational function of ⟨ρ v ⟩ that avoids recourse to Taylor series methods (which do not converge for large density differences). We have derived

  10. Development and Evaluation of Models for the Relationship between Tree Height and Diameter at Breast Height for Chinese-Fir Plantations in Subtropical China.

    Science.gov (United States)

    Li, Yan-qiong; Deng, Xiang-wen; Huang, Zhi-hong; Xiang, Wen-hua; Yan, Wen-de; Lei, Pi-feng; Zhou, Xiao-lu; Peng, Chang-hui

    2015-01-01

    Tree diameter at breast height (dbh) and height are the most important variables used in forest inventory and management as well as forest carbon-stock estimation. In order to identify the key stand variables that influence the tree height-dbh relationship and to develop and validate a suit of models for predicting tree height, data from 5961 tree samples aged from 6 years to 53 years and collected from 80 Chinese-fir plantation plots were used to fit 39 models, including 33 nonlinear models and 6 linear models, were developed and evaluated into two groups. The results showed that composite models performed better in height estimate than one-independent-variable models. Nonlinear composite Model 34 and linear composite Model 6 were recommended for predicting tree height in Chinese fir plantations with a dbh range between 4 cm and 40 cm when the dbh data for each tree and the quadratic mean dbh of the stand (Dq) and mean height of the stand (Hm) were available. Moreover, Hm could be estimated by using the formula Hm = 11.707 × l n(Dq)-18.032. Clearly, Dq was the primary stand variable that influenced the height-dbh relationship. The parameters of the models varied according to stand age and site. The inappropriate application of provincial or regional height-dbh models for predicting small tree height at local scale may result in larger uncertainties. The method and the recommended models developed in this study were statistically reliable for applications in growth and yield estimation for even-aged Chinese-fir plantation in Huitong and Changsha. The models could be extended to other regions and to other tree species only after verification in subtropical China.

  11. Predicting vertical jump height from bar velocity.

    Science.gov (United States)

    García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

    2015-06-01

    The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance.

  12. Variability analysis of AGN: a review of results using new statistical criteria

    Science.gov (United States)

    Zibecchi, L.; Andruchow, I.; Cellone, S. A.; Romero, G. E.; Combi, J. A.

    We present here a re-analysis of the variability results of a sample of active galactic nuclei (AGN), which have been observed on several sessions with the 2.15 m "Jorge Sahade" telescope (CASLEO), San Juan, Argentina, and whose results are published (Romero et al. 1999, 2000, 2002; Cellone et al. 2000). The motivation for this new analysis is the implementation, dur- ing the last years, of improvements in the statistical criteria applied, taking quantitatively into account the incidence of the photometric errors (Cellone et al. 2007). This work is framed as a first step in an integral study on the statistical estimators of AGN variability. This study is motivated by the great diversity of statistical tests that have been proposed to analyze the variability of these objects. Since we note that, in some cases, the results of the object variability depend on the test used, we attempt to make a com- parative study of the various tests and analyze, under the given conditions, which of them is the most efficient and reliable.

  13. Monosomy 3 by FISH in uveal melanoma: variability in techniques and results.

    Science.gov (United States)

    Aronow, Mary; Sun, Yang; Saunthararajah, Yogen; Biscotti, Charles; Tubbs, Raymond; Triozzi, Pierre; Singh, Arun D

    2012-09-01

    Tumor monosomy 3 confers a poor prognosis in patients with uveal melanoma. We critically review the techniques used for fluorescence in situ hybridization (FISH) detection of monosomy 3 in order to assess variability in practice patterns and to explain differences in results. Significant variability that has likely affected reported results was found in tissue sampling methods, selection of FISH probes, number of cells counted, and the cut-off point used to determine monosomy 3 status. Clinical parameters and specific techniques employed to report FISH results should be specified so as to allow meta-analysis of published studies. FISH-based detection of monosomy 3 in uveal melanoma has not been performed in a standardized manner, which limits conclusions regarding its clinical utility. FISH is a widely available, versatile technology, and when performed optimally has the potential to be a valuable tool for determining the prognosis of uveal melanoma. Copyright © 2012 Elsevier Inc. All rights reserved.

  14. Neural network cloud top pressure and height for MODIS

    Science.gov (United States)

    Håkansson, Nina; Adok, Claudia; Thoss, Anke; Scheirer, Ronald; Hörnquist, Sara

    2018-06-01

    Cloud top height retrieval from imager instruments is important for nowcasting and for satellite climate data records. A neural network approach for cloud top height retrieval from the imager instrument MODIS (Moderate Resolution Imaging Spectroradiometer) is presented. The neural networks are trained using cloud top layer pressure data from the CALIOP (Cloud-Aerosol Lidar with Orthogonal Polarization) dataset. Results are compared with two operational reference algorithms for cloud top height: the MODIS Collection 6 Level 2 height product and the cloud top temperature and height algorithm in the 2014 version of the NWC SAF (EUMETSAT (European Organization for the Exploitation of Meteorological Satellites) Satellite Application Facility on Support to Nowcasting and Very Short Range Forecasting) PPS (Polar Platform System). All three techniques are evaluated using both CALIOP and CPR (Cloud Profiling Radar for CloudSat (CLOUD SATellite)) height. Instruments like AVHRR (Advanced Very High Resolution Radiometer) and VIIRS (Visible Infrared Imaging Radiometer Suite) contain fewer channels useful for cloud top height retrievals than MODIS, therefore several different neural networks are investigated to test how infrared channel selection influences retrieval performance. Also a network with only channels available for the AVHRR1 instrument is trained and evaluated. To examine the contribution of different variables, networks with fewer variables are trained. It is shown that variables containing imager information for neighboring pixels are very important. The error distributions of the involved cloud top height algorithms are found to be non-Gaussian. Different descriptive statistic measures are presented and it is exemplified that bias and SD (standard deviation) can be misleading for non-Gaussian distributions. The median and mode are found to better describe the tendency of the error distributions and IQR (interquartile range) and MAE (mean absolute error) are found

  15. A survey for variable young stars with small telescopes: First results from HOYS-CAPS

    Science.gov (United States)

    Froebrich, D.; Campbell-White, J.; Scholz, A.; Eislöffel, J.; Zegmott, T.; Billington, S. J.; Donohoe, J.; Makin, S. V.; Hibbert, R.; Newport, R. J.; Pickard, R.; Quinn, N.; Rodda, T.; Piehler, G.; Shelley, M.; Parkinson, S.; Wiersema, K.; Walton, I.

    2018-05-01

    Variability in Young Stellar Objects (YSOs) is one of their primary characteristics. Long-term, multi-filter, high-cadence monitoring of large YSO samples is the key to understand the partly unusual light-curves that many of these objects show. Here we introduce and present the first results of the HOYS-CAPScitizen science project which aims to perform such monitoring for nearby (d < 1 kpc) and young (age < 10 Myr) clusters and star forming regions, visible from the northern hemisphere, with small telescopes. We have identified and characterised 466 variable (413 confirmed young) stars in 8 young, nearby clusters. All sources vary by at least 0.2 mag in V, have been observed at least 15 times in V, R and I in the same night over a period of about 2 yrs and have a Stetson index of larger than 1. This is one of the largest samples of variable YSOs observed over such a time-span and cadence in multiple filters. About two thirds of our sample are classical T-Tauri stars, while the rest are objects with depleted or transition disks. Objects characterised as bursters show by far the highest variability. Dippers and objects whose variability is dominated by occultations from normal interstellar dust or dust with larger grains (or opaque material) have smaller amplitudes. We have established a hierarchical clustering algorithm based on the light-curve properties which allows the identification of the YSOs with the most unusual behaviour, and to group sources with similar properties. We discuss in detail the light-curves of the unusual objects V2492 Cyg, V350 Cep and 2MASS J21383981+5708470.

  16. Effect of flow rate on environmental variables and phytoplankton dynamics: results from field enclosures

    Science.gov (United States)

    Zhang, Haiping; Chen, Ruihong; Li, Feipeng; Chen, Ling

    2015-03-01

    To investigate the effects of flow rate on phytoplankton dynamics and related environment variables, a set of enclosure experiments with different flow rates were conducted in an artificial lake. We monitored nutrients, temperature, dissolved oxygen, pH, conductivity, turbidity, chlorophyll- a and phytoplankton levels. The lower biomass in all flowing enclosures showed that flow rate significantly inhibited the growth of phytoplankton. A critical flow rate occurred near 0.06 m/s, which was the lowest relative inhibitory rate. Changes in flow conditions affected algal competition for light, resulting in a dramatic shift in phytoplankton composition, from blue-green algae in still waters to green algae in flowing conditions. These findings indicate that critical flow rate can be useful in developing methods to reduce algal bloom occurrence. However, flow rate significantly enhanced the inter-relationships among environmental variables, in particular by inducing higher water turbidity and vegetative reproduction of periphyton ( Spirogyra). These changes were accompanied by a decrease in underwater light intensity, which consequently inhibited the photosynthetic intensity of phytoplankton. These results warn that a universal critical flow rate might not exist, because the effect of flow rate on phytoplankton is interlinked with many other environmental variables.

  17. Genetical variability of Gladioli as the result of gamma-radiation

    International Nuclear Information System (INIS)

    Jakota, L.I.; Murin, A.V.

    1994-01-01

    In the starting material of Gladioli, got in the result of Y-radiation, the forms with white spots on the petals were observed. The Gladioli form 165-81 is distinguished by low growth and middle early flowering. The flower form is triangular. Basic pigmentation is red. White spots of different size on the petals were observed. The investigation was made in 1992 in the field of genetical variability of Gladioli. The Gladioli form 165-81 was irradiated with gamma-radiation dose 30 Gr. As a result the depression of biometric indicators was observed. Consequently, 30 Gr is a mutant dose for Gladioli

  18. Disaggregating measurement uncertainty from population variability and Bayesian treatment of uncensored results

    International Nuclear Information System (INIS)

    Strom, Daniel J.; Joyce, Kevin E.; Maclellan, Jay A.; Watson, David J.; Lynch, Timothy P.; Antonio, Cheryl L.; Birchall, Alan; Anderson, Kevin K.; Zharov, Peter

    2012-01-01

    In making low-level radioactivity measurements of populations, it is commonly observed that a substantial portion of net results are negative. Furthermore, the observed variance of the measurement results arises from a combination of measurement uncertainty and population variability. This paper presents a method for disaggregating measurement uncertainty from population variability to produce a probability density function (PDF) of possibly true results. To do this, simple, justifiable, and reasonable assumptions are made about the relationship of the measurements to the measurands (the 'true values'). The measurements are assumed to be unbiased, that is, that their average value is the average of the measurands. Using traditional estimates of each measurement's uncertainty to disaggregate population variability from measurement uncertainty, a PDF of measurands for the population is produced. Then, using Bayes's theorem, the same assumptions, and all the data from the population of individuals, a prior PDF is computed for each individual's measurand. These PDFs are non-negative, and their average is equal to the average of the measurement results for the population. The uncertainty in these Bayesian posterior PDFs is all Berkson with no remaining classical component. The methods are applied to baseline bioassay data from the Hanford site. The data include 90Sr urinalysis measurements on 128 people, 137Cs in vivo measurements on 5,337 people, and 239Pu urinalysis measurements on 3,270 people. The method produces excellent results for the 90Sr and 137Cs measurements, since there are nonzero concentrations of these global fallout radionuclides in people who have not been occupationally exposed. The method does not work for the 239Pu measurements in non-occupationally exposed people because the population average is essentially zero.

  19. Height and Breast Cancer Risk

    DEFF Research Database (Denmark)

    Zhang, Ben; Shu, Xiao-Ou; Delahanty, Ryan J

    2015-01-01

    BACKGROUND: Epidemiological studies have linked adult height with breast cancer risk in women. However, the magnitude of the association, particularly by subtypes of breast cancer, has not been established. Furthermore, the mechanisms of the association remain unclear. METHODS: We performed a meta......-analysis to investigate associations between height and breast cancer risk using data from 159 prospective cohorts totaling 5216302 women, including 113178 events. In a consortium with individual-level data from 46325 case patients and 42482 control patients, we conducted a Mendelian randomization analysis using...... a genetic score that comprised 168 height-associated variants as an instrument. This association was further evaluated in a second consortium using summary statistics data from 16003 case patients and 41335 control patients. RESULTS: The pooled relative risk of breast cancer was 1.17 (95% confidence...

  20. National evaluation of strategies to reduce safety violations for working from heights in construction companies: results from a randomized controlled trial.

    Science.gov (United States)

    van der Molen, Henk F; den Herder, Aalt; Warning, Jan; Frings-Dresen, Monique H W

    2016-01-09

    The objective of this study is to evaluate the effectiveness of a face-to-face strategy and a direct mail strategy on safety violations while working from heights among construction companies compared to a control condition. Construction companies with workers at risk for fall injuries were eligible for this three-armed randomized controlled trial. In total, 27 cities were randomly assigned to intervention groups-where eligible companies were given either a face-to-face guidance strategy or a direct mailing strategy with access to internet facilities-or to a control group. The primary outcomes were the number and type of safety violations recorded by labor inspectors after three months. A process evaluation for both strategies was performed to determine reach, program implementation, satisfaction, knowledge and perceived safety behavior. A cost analysis was performed to establish the financial costs for each intervention strategy. Analyses were done by intention to treat. In total, 41% (n = 88) of the companies eligible for the face-to-face intervention participated and 73% (n = 69) for direct mail. Intervention materials were delivered to 69 % (face-to-face group) and 100 % (direct mail group); completion of intervention activities within companies was low. Satisfaction, increase in knowledge, and safety behavior did not differ between the intervention groups. Costs for personal advice were 28% higher than for direct mail. Ultimately, nine intervention companies were captured in the 288 worksite measurements performed by the labor inspectorate. No statistical differences in mean number of safety violations (1.8-2.4) or penalties (72%-100%) were found between the intervention and control groups based on all worksite inspections. No conclusions about the effect of face-to-face and direct mail strategies on safety violations could be drawn due to the limited number of intervention companies captured in the primary outcome measurements. The costs for a face

  1. In defense of the classical height system

    Science.gov (United States)

    Foroughi, Ismael; Vaníček, Petr; Sheng, Michael; Kingdon, Robert William; Santos, Marcelo C.

    2017-11-01

    leveling points range between - 9.5 and 0 cm, differences between Helmert's and the rigorous orthometric heights vary between - 3.6 and 1.1 cm. The local gravimetric geoid model of Auvergne, computed by the Stokes-Helmert technique, is used here to illustrate the accuracy of the classical height system. Results show a very reasonable standard deviation (STD) of 3.2 cm of the differences between geoid values, derived from control leveling points, and gravimetric geoid heights when Helmert's heights are employed and even a smaller STD of 2.9 cm when rigorous orthometric heights are used. A corresponding comparison of a quasi-geoid model, computed by Least-Squares Modification of Stokes method, with normal heights show an STD of 3.4 cm.

  2. Results of the study of variables related to tasks of workers of a radioactive facility

    International Nuclear Information System (INIS)

    Alves, Alice S.; Campos, Daniela; Carneiro, Janete C.G.G.

    2015-01-01

    This paper presents the results of the evaluation study of the association degree between physical risk agent, ionizing radiation, and tasks performed by the occupationally exposed individuals (OEI), in the production of radioisotopes and radiopharmaceuticals of a radioactive facility. Initially, has been performed a qualitative assessment of the workplace, work groups and the processes as well. Starting from the inventoried subjective information, interviews and observations were identified seven homogeneous exposure groups, assuming they receive the same exposure to a range of specific agents. The data were analyzed by means of descriptive statistics with quantitative and qualitative approaches of the variables. In the analysis was used nonparametric tests (Equality of two proportions, Chi-square and Yates correction), descriptive measures of location (mean, median and quartiles) and dispersion (standard deviation and coefficient of variation). A significance level of 5% (p < 0.05) was adopted. The results have shown five risk factors (variables) related to the tasks performance. After the characterization distribution of the relative frequencies, all variables showed a significant degree of association (p < 0.001) to the exposure to ionizing radiation. Descriptive analysis of effective doses received by OEIs (n=102) resulted in the average of 4.06 mSv obtained in 2013 and 3.41 mSv in 2014. The collective doses corresponding to the same year were 414.41 mSv.person and 347.61 mSv.person. The doses values found during the analyzed period are in accordance to the limits established by the current national standards. (author)

  3. Results of the study of variables related to tasks of workers of a radioactive facility

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Alice S.; Campos, Daniela; Carneiro, Janete C.G.G., E-mail: alicesante@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    This paper presents the results of the evaluation study of the association degree between physical risk agent, ionizing radiation, and tasks performed by the occupationally exposed individuals (OEI), in the production of radioisotopes and radiopharmaceuticals of a radioactive facility. Initially, has been performed a qualitative assessment of the workplace, work groups and the processes as well. Starting from the inventoried subjective information, interviews and observations were identified seven homogeneous exposure groups, assuming they receive the same exposure to a range of specific agents. The data were analyzed by means of descriptive statistics with quantitative and qualitative approaches of the variables. In the analysis was used nonparametric tests (Equality of two proportions, Chi-square and Yates correction), descriptive measures of location (mean, median and quartiles) and dispersion (standard deviation and coefficient of variation). A significance level of 5% (p < 0.05) was adopted. The results have shown five risk factors (variables) related to the tasks performance. After the characterization distribution of the relative frequencies, all variables showed a significant degree of association (p < 0.001) to the exposure to ionizing radiation. Descriptive analysis of effective doses received by OEIs (n=102) resulted in the average of 4.06 mSv obtained in 2013 and 3.41 mSv in 2014. The collective doses corresponding to the same year were 414.41 mSv.person and 347.61 mSv.person. The doses values found during the analyzed period are in accordance to the limits established by the current national standards. (author)

  4. Variability of creatinine measurements in clinical laboratories: results from the CRIC study.

    Science.gov (United States)

    Joffe, Marshall; Hsu, Chi-yuan; Feldman, Harold I; Weir, Matthew; Landis, J R; Hamm, L Lee

    2010-01-01

    Estimating equations using serum creatinine (SCr) are often used to assess glomerular filtration rate (GFR). Such creatinine (Cr)-based formulae may produce biased estimates of GFR when using Cr measurements that have not been calibrated to reference laboratories. In this paper, we sought to examine the degree of this variation in Cr assays in several laboratories associated with academic medical centers affiliated with the Chronic Renal Insufficiency Cohort (CRIC) Study; to consider how best to correct for this variation, and to quantify the impact of such corrections on eligibility for participation in CRIC. Variability of Cr is of particular concern in the conduct of CRIC, a large multicenter study of subjects with chronic renal disease, because eligibility for the study depends on Cr-based assessment of GFR. A library of 5 large volume plasma specimens from apheresis patients was assembled, representing levels of plasma Cr from 0.8 to 2.4 mg/dl. Samples from this library were used for measurement of Cr at each of the 14 CRIC laboratories repetitively over time. We used graphical displays and linear regression methods to examine the variability in Cr, and used linear regression to develop calibration equations. We also examined the impact of the various calibration equations on the proportion of subjects screened as potential participants who were actually eligible for the study. There was substantial variability in Cr assays across laboratories and over time. We developed calibration equations for each laboratory; these equations varied substantially among laboratories and somewhat over time in some laboratories. The laboratory site contributed the most to variability (51% of the variance unexplained by the specimen) and variation with time accounted for another 15%. In some laboratories, calibration equations resulted in differences in eligibility for CRIC of as much as 20%. The substantial variability in SCr assays across laboratories necessitates calibration

  5. Social inequalities in height: persisting differences today depend upon height of the parents.

    Directory of Open Access Journals (Sweden)

    Bruna Galobardes

    Full Text Available Substantial increases in height have occurred concurrently with economic development in most populations during the last century. In high-income countries, environmental exposures that can limit genetic growth potential appear to have lessened, and variation in height by socioeconomic position may have diminished. The objective of this study is to investigate inequalities in height in a cohort of children born in the early 1990s in England, and to evaluate which factors might explain any identified inequalities.12,830 children from The Avon Longitudinal Study of Parents and Children (ALSPAC, a population based cohort from birth to about 11.5 years of age, were used in this analysis. Gender- and age-specific z-scores of height at different ages were used as outcome variables. Multilevel models were used to take into account the repeated measures of height and to analyze gender- and age-specific relative changes in height from birth to 11.5 years. Maternal education was the main exposure variable used to examine socioeconomic inequalities. The roles of parental and family characteristics in explaining any observed differences between maternal education and child height were investigated. Children whose mothers had the highest education compared to those with none or a basic level of education, were 0.39 cm longer at birth (95% CI: 0.30 to 0.48. These differences persisted and at 11.5 years the height difference was 1.4 cm (95% CI: 1.07 to 1.74. Several other factors were related to offspring height, but few changed the relationship with maternal education. The one exception was mid-parental height, which fully accounted for the maternal educational differences in offspring height.In a cohort of children born in the 1990s, mothers with higher education gave birth to taller boys and girls. Although height differences were small they persisted throughout childhood. Maternal and paternal height fully explained these differences.

  6. Results of Propellant Mixing Variable Study Using Precise Pressure-Based Burn Rate Calculations

    Science.gov (United States)

    Stefanski, Philip L.

    2014-01-01

    A designed experiment was conducted in which three mix processing variables (pre-curative addition mix temperature, pre-curative addition mixing time, and mixer speed) were varied to estimate their effects on within-mix propellant burn rate variability. The chosen discriminator for the experiment was the 2-inch diameter by 4-inch long (2x4) Center-Perforated (CP) ballistic evaluation motor. Motor nozzle throat diameters were sized to produce a common targeted chamber pressure. Initial data analysis did not show a statistically significant effect. Because propellant burn rate must be directly related to chamber pressure, a method was developed that showed statistically significant effects on chamber pressure (either maximum or average) by adjustments to the process settings. Burn rates were calculated from chamber pressures and these were then normalized to a common pressure for comparative purposes. The pressure-based method of burn rate determination showed significant reduction in error when compared to results obtained from the Brooks' modification of the propellant web-bisector burn rate determination method. Analysis of effects using burn rates calculated by the pressure-based method showed a significant correlation of within-mix burn rate dispersion to mixing duration and the quadratic of mixing duration. The findings were confirmed in a series of mixes that examined the effects of mixing time on burn rate variation, which yielded the same results.

  7. Potential fitting biases resulting from grouping data into variable width bins

    International Nuclear Information System (INIS)

    Towers, S.

    2014-01-01

    When reading peer-reviewed scientific literature describing any analysis of empirical data, it is natural and correct to proceed with the underlying assumption that experiments have made good faith efforts to ensure that their analyses yield unbiased results. However, particle physics experiments are expensive and time consuming to carry out, thus if an analysis has inherent bias (even if unintentional), much money and effort can be wasted trying to replicate or understand the results, particularly if the analysis is fundamental to our understanding of the universe. In this note we discuss the significant biases that can result from data binning schemes. As we will show, if data are binned such that they provide the best comparison to a particular (but incorrect) model, the resulting model parameter estimates when fitting to the binned data can be significantly biased, leading us to too often accept the model hypothesis when it is not in fact true. When using binned likelihood or least squares methods there is of course no a priori requirement that data bin sizes need to be constant, but we show that fitting to data grouped into variable width bins is particularly prone to produce biased results if the bin boundaries are chosen to optimize the comparison of the binned data to a wrong model. The degree of bias that can be achieved simply with variable binning can be surprisingly large. Fitting the data with an unbinned likelihood method, when possible to do so, is the best way for researchers to show that their analyses are not biased by binning effects. Failing that, equal bin widths should be employed as a cross-check of the fitting analysis whenever possible

  8. Potential fitting biases resulting from grouping data into variable width bins

    Energy Technology Data Exchange (ETDEWEB)

    Towers, S., E-mail: smtowers@asu.edu

    2014-07-30

    When reading peer-reviewed scientific literature describing any analysis of empirical data, it is natural and correct to proceed with the underlying assumption that experiments have made good faith efforts to ensure that their analyses yield unbiased results. However, particle physics experiments are expensive and time consuming to carry out, thus if an analysis has inherent bias (even if unintentional), much money and effort can be wasted trying to replicate or understand the results, particularly if the analysis is fundamental to our understanding of the universe. In this note we discuss the significant biases that can result from data binning schemes. As we will show, if data are binned such that they provide the best comparison to a particular (but incorrect) model, the resulting model parameter estimates when fitting to the binned data can be significantly biased, leading us to too often accept the model hypothesis when it is not in fact true. When using binned likelihood or least squares methods there is of course no a priori requirement that data bin sizes need to be constant, but we show that fitting to data grouped into variable width bins is particularly prone to produce biased results if the bin boundaries are chosen to optimize the comparison of the binned data to a wrong model. The degree of bias that can be achieved simply with variable binning can be surprisingly large. Fitting the data with an unbinned likelihood method, when possible to do so, is the best way for researchers to show that their analyses are not biased by binning effects. Failing that, equal bin widths should be employed as a cross-check of the fitting analysis whenever possible.

  9. Relationships between diameter and height of trees in natural ...

    African Journals Online (AJOL)

    Relationships between diameter and height of trees in natural tropical forest in Tanzania. Wilson A Mugasha, Ole M Bollandsås, Tron Eid. Abstract. The relationship between tree height (h) and tree diameter at breast height (dbh) is an important element describing forest stands. In addition, h often is a required variable in ...

  10. Some results on convergence rates for probabilities of moderate deviations for sums of random variables

    Directory of Open Access Journals (Sweden)

    Deli Li

    1992-01-01

    Full Text Available Let X, Xn, n≥1 be a sequence of iid real random variables, and Sn=∑k=1nXk, n≥1. Convergence rates of moderate deviations are derived, i.e., the rate of convergence to zero of certain tail probabilities of the partial sums are determined. For example, we obtain equivalent conditions for the convergence of series ∑n≥1(ψ2(n/nP(|Sn|≥nφ(n only under the assumptions convergence that EX=0 and EX2=1, where φ and ψ are taken from a broad class of functions. These results generalize and improve some recent results of Li (1991 and Gafurov (1982 and some previous work of Davis (1968. For b∈[0,1] and ϵ>0, letλϵ,b=∑n≥3((loglognb/nI(|Sn|≥(2+ϵnloglogn.The behaviour of Eλϵ,b as ϵ↓0 is also studied.

  11. Physiological pattern of lumbar disc height

    International Nuclear Information System (INIS)

    Biggemann, M.; Frobin, W.; Brinckmann, P.

    1997-01-01

    Purpose of this study is to present a new method of quantifying objectively the height of all discs in lateral radiographs of the lumbar spine and of analysing the normal craniocaudal sequence pattern of lumbar disc heights. Methods: The new parameter is the ventrally measured disc height corrected for the dependence on the angle of lordosis by normalisation to mean angles observed in the erect posture of healthy persons. To eliminate radiographic magnification, the corrected ventral height is related to the mean depth of the cranially adjoining vertebra. In this manner lumbar disc heights were objectively measured in young, mature and healthy persons (146 males and 65 females). The craniocaudal sequence pattern was analysed by mean values from all persons and by height differences of adjoining discs in each individual lumbar spine. Results: Mean normative values demonstrated an increase in disc height between L1/L2 and L4/L5 and a constant or decreasing disc height between L4/L5 and L5/S1. However, this 'physiological sequence of disc height in the statistical mean' was observed in only 36% of normal males and 55% of normal females. Conclusion: The radiological pattern of the 'physiological sequence of lumbar disc height' leads to a relevant portion of false positive pathological results especially at L4/L5. An increase of disc height from L4/L5 to L5/S1 may be normal. The recognition of decreased disc height should be based on an abrupt change in the heights of adjoining discs and not on a deviation from a craniocaudal sequence pattern. (orig.) [de

  12. PHOTOMETRY OF VARIABLE STARS FROM DOME A, ANTARCTICA: RESULTS FROM THE 2010 OBSERVING SEASON

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lingzhi; Zhu, Zonghong [Department of Astronomy, Beijing Normal University, Beijing 100875 (China); Macri, Lucas M.; Wang, Lifan [Mitchell Institute for Fundamental Physics and Astronomy, Department of Physics and Astronomy, Texas A and M University, College Station, TX 77843 (United States); Ashley, Michael C. B.; Lawrence, Jon S.; Luong-Van, Daniel; Storey, John W. V. [School of Physics, University of New South Wales, NSW 2052 (Australia); Cui, Xiangqun; Feng, Long-Long; Gong, Xuefei; Liu, Qiang; Shang, Zhaohui; Yang, Huigen; Yang, Ji; Yuan, Xiangyan; Zhou, Xu; Zhu, Zhenxi [Chinese Center for Antarctic Astronomy, Nanjing 210008 (China); Pennypacker, Carl R. [Center for Astrophysics, Lawrence Berkeley National Laboratory, Berkeley, CA (United States); York, Donald G., E-mail: wanglingzhi@bao.ac.cn [Department of Astronomy and Astrophysics and Enrico Fermi Institute, University of Chicago, Chicago, IL 60637 (United States)

    2013-12-01

    We present results from a season of observations with the Chinese Small Telescope ARray, obtained over 183 days of the 2010 Antarctic winter. We carried out high-cadence time-series aperture photometry of 9125 stars with i ∼< 15.3 mag located in a 23 deg{sup 2} region centered on the south celestial pole. We identified 188 variable stars, including 67 new objects relative to our 2008 observations, thanks to broader synoptic coverage, a deeper magnitude limit, and a larger field of view. We used the photometric data set to derive site statistics from Dome A. Based on two years of observations, we find that extinction due to clouds at this site is less than 0.1 and 0.4 mag during 45% and 75% of the dark time, respectively.

  13. Lucas Heights technology park

    International Nuclear Information System (INIS)

    1987-01-01

    The proposed Lucas Heights Technology Park will pound together the applied research programs of Government, tertiary and industry sectors, aiming to foster technology transfer particularly to the high-technology manufacturing industry. A description of the site is given along with an outline of the envisaged development, existing facilities and expertise. ills

  14. Small scale denitrification variability in riparian zones: Results from a high-resolution dataset

    Science.gov (United States)

    Gassen, Niklas; Knöller, Kay; Musolff, Andreas; Popp, Felix; Lüders, Tillmann; Stumpp, Christine

    2017-04-01

    Riparian zones are important compartments at the interface between groundwater and surface water where biogeochemical processes like denitrification are often enhanced. Nitrate loads of either groundwater entering a stream through the riparian zone or streamwater infiltrating into the riparian zone can be substantially reduced. These processes are spatially and temporally highly variable, making it difficult to capture solute variabilities, estimate realistic turnover rates and thus to quantify integral mass removal. A crucial step towards a more detailed characterization is to monitor solutes on a scale which adequately resemble the highly heterogeneous distribution and on a scale where processes occur. We measured biogeochemical parameters in a spatial high resolution within a riparian corridor of a German lowland river system over the course of one year. Samples were taken from three newly developed high-resolution multi-level wells with a maximum vertical resolution of 5 cm and analyzed for major ions, DOC and N-O isotopes. Sediment derived during installation of the wells was analyzed for specific denitrifying enzymes. Results showed a distinct depth zonation of hydrochemistry within the shallow alluvial aquifer, with a 1 m thick zone just below the water table with lower nitrate concentrations and EC values similar to the nearby river. Conservative parameters were consistent inbetween the three wells, but nitrate was highly variable. In addition, spots with low nitrate concentrations showed isotopic and microbial evidence for higher denitrification activities. The depth zonation was observed throughout the year, with stronger temporal variations of nitrate concentrations just below the water table compared to deeper layers. Nitrate isotopes showed a clear seasonal trend of denitrification activities (high in summer, low in winter). Our dataset gives new insight into river-groundwater exchange processes and shows the highly heterogeneous distribution of

  15. NOx emissions from large point sources: variability in ozone production, resulting health damages and economic costs

    International Nuclear Information System (INIS)

    Mauzerall, D.L.; Namsoug Kim

    2005-01-01

    We present a proof-of-concept analysis of the measurement of the health damage of ozone (O 3 ) produced from nitrogen oxides (NO x =NO+NO 2 ) emitted by individual large point sources in the eastern United States. We use a regional atmospheric model of the eastern United States, the Comprehensive Air quality Model with Extensions (CAMx), to quantify the variable impact that a fixed quantity of NO x emitted from individual sources can have on the downwind concentration of surface O 3 , depending on temperature and local biogenic hydrocarbon emissions. We also examine the dependence of resulting O 3 -related health damages on the size of the exposed population. The investigation is relevant to the increasingly widely used 'cap and trade' approach to NO x regulation, which presumes that shifts of emission over time and space, holding the total fixed over the course of the summer O 3 season, will have minimal effect on the environmental outcome. By contrast, we show that a shift of a unit of NO x emissions from one place or time to another could result in large changes in resulting health effects due to O 3 formation and exposure. We indicate how the type of modeling carried out here might be used to attach externality-correcting prices to emissions. Charging emitters fees that are commensurate with the damage caused by their NO x emissions would create an incentive for emitters to reduce emissions at times and in locations where they cause the largest damage. (author)

  16. Variables predicting elevated portal pressure in alcoholic liver disease. Results of a multivariate analysis

    DEFF Research Database (Denmark)

    Krogsgaard, K; Christensen, E; Gluud, C

    1987-01-01

    In 46 alcoholic patients the association of wedged-to-free hepatic-vein pressure with other variables (clinical, histologic, hemodynamic, and liver function data) was studied by means of multiple regression analysis, taking the wedged-to-free hepatic-vein pressure as the dependent variable. Four ...

  17. Seasonal variability in clinical care of COPD outpatients: results from the Andalusian COPD audit

    Directory of Open Access Journals (Sweden)

    López-Campos JL

    2017-03-01

    Full Text Available Jose Luis López-Campos,1,2 Maria Abad Arranz,1 Carmen Calero-Acuña,1,2 Fernando Romero-Valero,3 Ruth Ayerbe-García,4 Antonio Hidalgo-Molina,3 Ricardo I Aguilar-Pérez-Grovas,4 Francisco García-Gil,5 Francisco Casas-Maldonado,6 Laura Caballero-Ballesteros,5 María Sánchez-Palop,6 Dolores Pérez-Tejero,7 Alejandro Segado Soriano,7 Jose Calvo-Bonachera,8 Bárbara Hernández-Sierra,8 Adolfo Doménech,9 Macarena Arroyo-Varela,9 Francisco González-Vargas,10 Juan J Cruz-Rueda10 1Unidad Médico-Quirúrgica de Enfermedades Respiratorias, Instituto de Biomedicina de Sevilla (IBiS, Hospital Universitario Virgen del Rocío/Universidad de Sevilla, Seville, 2CIBER de Enfermedades Respiratorias (CIBERES, Instituto de Salud Carlos III, Madrid, 3Sección de Neumología, Hospital Puerta del Mar, Cádiz, 4Servicio de Neumología, Hospital Juan Ramón Jiménez, Huelva, 5Servicio de Neumología, Hospital Universitario Reina Sofía, Córdoba, 6Servicio de Neumología, Hospital Universitario San Cecilio, Granada, 7Sección de Neumología, Hospital Infanta Margarita, Cabra, Córdoba, 8Servicio de Neumología, Hospital Torrecárdenas, Almería, 9Servicio de Neumología, Hospital Regional Universitario de Málaga, Málaga, 10Servicio de Neumología, Hospital Universitario Virgen de las Nieves, Granada, Spain Objectives: Clinical practice in chronic obstructive pulmonary disease (COPD can be influenced by weather variability throughout the year. To explore the hypothesis of seasonal variability in clinical practice, the present study analyzes the results of the 2013–2014 Andalusian COPD audit with regard to changes in clinical practice according to the different seasons.Methods: The Andalusian COPD audit was a pilot clinical project conducted from October 2013 to September 2014 in outpatient respiratory clinics of hospitals in Andalusia, Spain (8 provinces with more than 8 million inhabitants with retrospective data gathering. For the present analysis

  18. Numerical analysis of the harmonic components of the Bragg wavelength content in spectral responses of apodized fiber Bragg gratings written by means of a phase mask with a variable phase step height.

    Science.gov (United States)

    Osuch, Tomasz

    2016-02-01

    The influence of the complex interference patterns created by a phase mask with variable diffraction efficiency in apodized fiber Bragg grating (FBGs) formation on their reflectance spectra is studied. The effect of the significant contributions of the zeroth and higher (m>±1) diffraction orders on the Bragg wavelength peak and its harmonic components is analyzed numerically. The results obtained for Gaussian and tanh apodization profiles are compared with similar data calculated for a uniform grating. It is demonstrated that when an apodized FBG is written using a phase mask with variable diffraction efficiency, significant enhancement of the harmonic components and a reduction of the Bragg wavelength peak in the grating spectral response are observed. This is particularly noticeable for the Gaussian apodization profile due to the substantial contributions of phase mask sections with relatively small phase steps in the FBG formation.

  19. APTCARE - Lucas Heights

    International Nuclear Information System (INIS)

    1986-05-01

    This plan details command co-ordination and support responses of Commonwealth and State Authorities in the event of an accident with offsite consequences at the Lucas Heights Research Laboratories. The plan has been prepared by the AAEC Local Liaison Working Party, comprising representatives of the Australian Atomic Energy Commission, NSW Police Department, NSW Board of Fire Commissioners, NSW State Emergency Services and Civil Defence Organisation, NSW Department of Health, NSW Department of Environment and Planning and Sutherland Shire Council

  20. [Variable magnetic fields in the treatment of tics disorders - preliminary results].

    Science.gov (United States)

    Pasek, Jarosław; Jędrzejewska, Anna; Jagodziński, Leszek; Obuchowicz, Anna; Flak, Maria; Sieroń, Aleksander

    Tics disorders is frequent pathological syndrome, particularly typical for children's age. The symptoms of this disease are differential, and their intensification individualized, which makes difficult unique recognition. Tics disorders concern the most often the muscles of face, head, upper limbs and trunk. The study group consisted of 16 patients (11 boys and 5 girls) with tics complex disorders about unknown etiology particularly relating of face and upper limbs muscles. In the treatment were the interventions with use a magnetotherapy and magnetostimulation applied. The procedures were ones daily by 3 weeks in two series executed. It author's pool was the frequency of occurrence tics disorders as well as the proportional opinion of effectiveness conducted treatment estimated. After 10 weeks in 14 patients was the decrease of occurrence frequency involuntary movements observed, in proportional scale about 75%. The results of subjective opinion of mood showed, that decrease the frequency tics disorders had in all children the direct shift on improvement their mood, and also satisfaction in their parents. The use of variable magnetic fields influenced on decrease the occurrence frequency tics disorders, and also on improvement quality of life the treated patients.

  1. Heritability of adult body height

    DEFF Research Database (Denmark)

    Silventoinen, Karri; Sammalisto, Sampo; Perola, Markus

    2003-01-01

    /unique environment (AE) model. Among women the heritability estimates were generally lower than among men with greater variation between countries, ranging from 0.68 to 0.84 when an additive genes/shared environment/unique environment (ACE) model was used. In four populations where an AE model fit equally well...... countries; body height was least in Italy (177 cm in men and 163 cm in women) and greatest in the Netherlands (184 cm and 171 cm, respectively). In men there was no corresponding variation in heritability of body height, heritability estimates ranging from 0.87 to 0.93 in populations under an additive genes...... or better, heritability ranged from 0.89 to 0.93. This difference between the sexes was mainly due to the effect of the shared environmental component of variance, which appears to be more important among women than among men in our study populations. Our results indicate that, in general, there are only...

  2. Variability and trends in the Arctic Sea ice cover: Results from different techniques

    Science.gov (United States)

    Comiso, Josefino C.; Meier, Walter N.; Gersten, Robert

    2017-08-01

    Variability and trend studies of sea ice in the Arctic have been conducted using products derived from the same raw passive microwave data but by different groups using different algorithms. This study provides consistency assessment of four of the leading products, namely, Goddard Bootstrap (SB2), Goddard NASA Team (NT1), EUMETSAT Ocean and Sea Ice Satellite Application Facility (OSI-SAF 1.2), and Hadley HadISST 2.2 data in evaluating variability and trends in the Arctic sea ice cover. All four provide generally similar ice patterns but significant disagreements in ice concentration distributions especially in the marginal ice zone and adjacent regions in winter and meltponded areas in summer. The discrepancies are primarily due to different ways the four techniques account for occurrences of new ice and meltponding. However, results show that the different products generally provide consistent and similar representation of the state of the Arctic sea ice cover. Hadley and NT1 data usually provide the highest and lowest monthly ice extents, respectively. The Hadley data also show the lowest trends in ice extent and ice area at -3.88%/decade and -4.37%/decade, respectively, compared to an average of -4.36%/decade and -4.57%/decade for all four. Trend maps also show similar spatial distribution for all four with the largest negative trends occurring at the Kara/Barents Sea and Beaufort Sea regions, where sea ice has been retreating the fastest. The good agreement of the trends especially with updated data provides strong confidence in the quantification of the rate of decline in the Arctic sea ice cover.Plain Language SummaryThe declining Arctic sea ice cover, especially in the summer, has been the center of attention in recent years. Reports on the sea ice cover have been provided by different institutions using basically the same set of satellite data but different techniques for estimating key parameters such as ice concentration, ice extent, and ice area. In

  3. Accuracy of recumbent height measurement.

    Science.gov (United States)

    Gray, D S; Crider, J B; Kelley, C; Dickinson, L C

    1985-01-01

    Since many patients requiring specialized nutritional support are bedridden, measurement of height for purposes of nutritional assessment or prescription must often be done with the patient in bed. This study examined the accuracy of measuring body height in bed in the supine position. Two measurements were performed on 108 ambulatory inpatients: (1) standing height using a standard height-weight scale, and (2) bed height using a flexible tape. Patients were divided into four groups based on which of two researchers performed each of the two measurements. Each patient was also weighed and self-reported height, weight, sex, and age were recorded. Bed height was significantly longer than standing height by 3.68 cm, but the two measurements were equally precise. It was believed, however, that this 2% difference was probably not clinically significant in most circumstances. Bed height correlated highly with standing height (r = 0.95), and the regression equation was standing height = 13.82 +/- 0.09 bed height. Patients overestimated their heights. Heights recorded by nurses were more accurate when patients were measured than when asked about their heights, but the patients were more often asked than measured.

  4. Final height and intrauterine growth retardation.

    Science.gov (United States)

    Tauber, Maïthé

    2017-06-01

    Approximately 10% of small for gestational age (SGA) children maintain a small body size throughout childhood and often into adult life with a decreased pubertal spurt. Growth hormone (GH) therapy increases short-term growth in a dose-dependent manner and adult height had now been well documented. Shorter children might benefit from a higher dose at start (50μg/kg/day). The response to GH treatment was similar for both preterm and term short SGA groups and the effect of GH treatment on adult height showed a wide variation in growth response. As a whole, mean adult height is higher than -2 SDS in 60% of patients and 70% reached an adult height in their target height with better results with higher doses and combined GnRH analog therapy in those who were short at onset of puberty. Copyright © 2017. Published by Elsevier Masson SAS.

  5. Observing Crop-Height Dynamics Using a UAV

    Science.gov (United States)

    Ziliani, M. G.; Parkes, S. D.; McCabe, M.

    2017-12-01

    Retrieval of vegetation height during a growing season is a key indicator for monitoring crop status, offering insight to the forecast yield relative to previous planting cycles. Improvement in Unmanned Aerial Vehicle (UAV) technologies, supported by advances in computer vision and photogrammetry software, has enabled retrieval of crop heights with much higher spatial resolution and coverage. These methodologies retrieve a Digital Surface Map (DSM), which combine terrain and crop elements to obtain a Crop Surface Map (CSM). Here we describe an automated method for deriving high resolution CSMs from a DSM, using RGB imagery from a UAV platform. Importantly, the approach does not require the need for a digital terrain map (DTM). The method involves distinguishing between vegetation and bare-ground cover pixels, using vegetation index maps from the RGB orthomosaic derived from the same flight as the DSM. We show that the absolute crop height can be extracted to within several centimeters, exploiting the data captured from a single UAV flight. In addition, the method is applied across five surveys during a maize growing cycle and compared against a terrain map constructed from a baseline UAV survey undertaken prior to crop growth. Results show that the approach is able to reproduce the observed spatial variability of the crop height within the maize field throughout the duration of the growing season. This is particularly valuable since it may be employed to detect intra-field problems (i.e. fertilizer variability, inefficiency in the irrigation system, salinity etc.) at different stages of the season, from which remedial action can be initiated to mitigate against yield loss. The method also demonstrates that UAV imagery combined with commercial photogrammetry software can determine a CSM from a single flight without the requirement of a prior DTM. This, together with the dynamic crop height estimation, provide useful information with which to inform precision

  6. Particles of bottom and suspended sediments: height of rise

    Directory of Open Access Journals (Sweden)

    Khodzinskaya Anna Gennadievna

    2014-12-01

    Full Text Available In the article, characteristic values of dynamic sizes of bottom and suspended sediments, including their probabilistic assessment, are considered. The article presents the processing results in respect of the experimental data for bottom and suspended sediments, obtained in the laboratory environment using samples and filming methods. The experiments have proven that the dynamic hydraulic size determines the height of rise for the particles of the saltation load, rather than suspended ones. In the laboratory environment, the maximal height of rise is mainly driven by the relative flow depth. According to the assessment made by the co-authors, depths of flows employed in the experiments designated for the identification of heights of rises, were comparable to saltation heights of particles. Besides, the saltation height of particles, having relative density well below 2.65, nearly always exceeded half of the depth of the laboratory flow. Hydrodynamic conditions favourable for the separation and motion of artificial particles in coarse surface tanks are far different from the motion of sand particles on the bottom of lowland rivers. Values of hydraulic resistance ratios typical for laboratory experiments by far exceed their values typical for lowland rivers, and it means that the conditions of the experiments performed in the laboratory were similar to those typical for mountain rivers. The research findings have proven that the particle separation and motion pattern, if artificial particles are made of the materials demonstrating variable density and elasticity values and if loose particles travel over fixed ones, is different from the pattern typical for natural particles having variable coarseness.

  7. Mapping Forest Canopy Height Across Large Areas by Upscaling ALS Estimates with Freely Available Satellite Data

    Directory of Open Access Journals (Sweden)

    Phil Wilkes

    2015-09-01

    Full Text Available Operational assessment of forest structure is an on-going challenge for land managers, particularly over large, remote or inaccessible areas. Here, we present an easily adopted method for generating a continuous map of canopy height at a 30 m resolution, demonstrated over 2.9 million hectares of highly heterogeneous forest (canopy height 0–70 m in Victoria, Australia. A two-stage approach was utilized where Airborne Laser Scanning (ALS derived canopy height, captured over ~18% of the study area, was used to train a regression tree ensemble method; random forest. Predictor variables, which have a global coverage and are freely available, included Landsat Thematic Mapper (Tasselled Cap transformed, Moderate Resolution Imaging Spectroradiometer Normalized Difference Vegetation Index time series, Shuttle Radar Topography Mission elevation data and other ancillary datasets. Reflectance variables were further processed to extract additional spatial and temporal contextual and textural variables. Modeled canopy height was validated following two approaches; (i random sample cross validation; and (ii with 108 inventory plots from outside the ALS capture extent. Both the cross validation and comparison with inventory data indicate canopy height can be estimated with a Root Mean Square Error (RMSE of ≤ 31% (~5.6 m at the 95th percentile confidence interval. Subtraction of the systematic component of model error, estimated from training data error residuals, rescaled canopy height values to more accurately represent the response variable distribution tails e.g., tall and short forest. Two further experiments were carried out to test the applicability and scalability of the presented method. Results suggest that (a no improvement in canopy height estimation is achieved when models were constructed and validated for smaller geographic areas, suggesting there is no upper limit to model scalability; and (b training data can be captured over a small

  8. Concordant preferences for actual height and facial cues to height

    OpenAIRE

    Re, Daniel Edward; Perrett, David I.

    2012-01-01

    Physical height has a well-documented effect on human mate preferences. In general, both sexes prefer opposite-sex romantic relationships in which the man is taller than the woman, while individual preferences for height are affected by a person’s own height. Research in human mate choice has demonstrated that attraction to facial characteristics, such as facial adiposity, may reflect references for body characteristics. Here, we tested preferences for facial cues to height. In general, incre...

  9. Optimal Height Calculation and Modelling of Noise Barrier

    Directory of Open Access Journals (Sweden)

    Raimondas Grubliauskas

    2011-04-01

    Full Text Available Transport is one of the main sources of noise having a particularly strong negative impact on the environment. In the city, one of the best methods to reduce the spread of noise in residential areas is a noise barrier. The article presents noise reduction barrier adaptation with empirical formulas calculating and modelling noise distribution. The simulation of noise dispersion has been performed applying the CadnaA program that allows modelling the noise levels of various developments under changing conditions. Calculation and simulation is obtained by assessing the level of noise reduction using the same variables. The investigation results are presented as noise distribution isolines. The selection of a different height of noise barriers are the results calculated at the heights of 1, 4 and 15 meters. The level of noise reduction at the maximum overlap of data, calculation and simulation has reached about 10%.Article in Lithuanian

  10. Methods for Minimization and Management of Variability in Long-Term Groundwater Monitoring Results

    Science.gov (United States)

    2015-12-01

    DECEMBER 2015 Poonam Kulkarni Charles Newell Claire Krebs Thomas McHugh GSI Environmental, Inc. Britt Sanford ProHydro Distribution...based on an understanding of the short-term variability and long-term attenuation rate at a particular site ( McHugh et al., 2015a). The...time is independent of these parameters ( McHugh et al., 2015c). The relative trade-off between monitoring frequency and time required to

  11. Statistical analysis of nuclear power plant pump failure rate variability: some preliminary results

    International Nuclear Information System (INIS)

    Martz, H.F.; Whiteman, D.E.

    1984-02-01

    In-Plant Reliability Data System (IPRDS) pump failure data on over 60 selected pumps in four nuclear power plants are statistically analyzed using the Failure Rate Analysis Code (FRAC). A major purpose of the analysis is to determine which environmental, system, and operating factors adequately explain the variability in the failure data. Catastrophic, degraded, and incipient failure severity categories are considered for both demand-related and time-dependent failures. For catastrophic demand-related pump failures, the variability is explained by the following factors listed in their order of importance: system application, pump driver, operating mode, reactor type, pump type, and unidentified plant-specific influences. Quantitative failure rate adjustments are provided for the effects of these factors. In the case of catastrophic time-dependent pump failures, the failure rate variability is explained by three factors: reactor type, pump driver, and unidentified plant-specific influences. Finally, point and confidence interval failure rate estimates are provided for each selected pump by considering the influential factors. Both types of estimates represent an improvement over the estimates computed exclusively from the data on each pump

  12. Height perception influenced by texture gradient.

    Science.gov (United States)

    Tozawa, Junko

    2012-01-01

    Three experiments were carried out to examine whether a texture gradient influences perception of relative object height. Previous research implicated texture cues in judgments of object width, but similar influences have not been demonstrated for relative height. In this study, I evaluate a hypothesis that the projective ratio of the number of texture elements covered by the objects combined with the ratio of the retinal object heights determines percepts of relative object height. Density of texture background was varied: four density conditions ranged from no-texture to very dense texture. In experiments 1 and 2, participants judged the height of comparison bar compared to the standard bar positioned on no-texture or textured backgrounds. Results showed relative height judgments differed with texture manipulations, consistent with predictions from a hypothesised combination of the number of texture elements with retinal height (experiment 1), or partially consistent with this hypothesis (experiment 2). In experiment 2, variations in the position of a comparison object showed that comparisons located far from the horizon were judged more poorly than in other positions. In experiment 3 I examined distance perception; relative distance judgments were found to be also affected by textured backgrounds. Results are discussed in terms of Gibson's relational theory and distance calibration theory.

  13. Sexual Orientation, Objective Height, and Self-Reported Height.

    Science.gov (United States)

    Skorska, Malvina N; Bogaert, Anthony F

    2017-01-01

    Studies that have used mostly self-reported height have found that androphilic men and women are shorter than gynephilic men and women, respectively. This study examined whether an objective height difference exists or whether a psychosocial account (e.g., distortion of self-reports) may explain these putative height differences. A total of 863 participants, recruited at a Canadian university, the surrounding region, and through lesbian, gay, bisexual, and transgender (LGBT) events across Canada, self-reported their height and had their height measured. Androphilic men were shorter, on average, than gynephilic men. There was no objective height difference between gynephilic, ambiphilic, and androphilic women. Self-reported height, statistically controlling for objective height, was not related to sexual orientation. These findings are the first to show an objective height difference between androphilic and gynephilic men. Also, the findings suggest that previous studies using self-reported height found part of a true objective height difference between androphilic and gynephilic men. These findings have implications for existing biological theories of men's sexual orientation development.

  14. Some Results on facets for linear inequality in 0-1 variables

    Directory of Open Access Journals (Sweden)

    D. Sashi Bhusan

    2010-03-01

    Full Text Available The facet of Knapsack ploytope, i.e. convex hull of 0-1 points satisfying a given linear inequality has been presented in this current paper. Such type of facets plays an important role in set covering set partitioning, matroidal-intersection vertex- packing, generalized assignment and other combinatorial problems. Strong covers for facets of Knapsack ploytope has been developed in the first part of the present paper. Generating family of valid cutting planes that satisfy inequality with 0-1 variables through algorithms are the attraction of this paper.

  15. Sri Lanka, Colored Height

    Science.gov (United States)

    2005-01-01

    The topography of the island nation of Sri Lanka is well shown in this color-coded shaded relief map generated with digital elevation data from the Shuttle Radar Topography Mission (SRTM). Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. For this special view heights below 10 meters (33 feet) above sea level have been colored red. These low coastal elevations extend 5 to 10 km (3.1 to 6.2 mi) inland on Sri Lanka and are especially vulnerable to flooding associated with storm surges, rising sea level, or, as in the aftermath of the earthquake of December 26, 2004, tsunami. These so-called tidal waves have occurred numerous times in history and can be especially destructive, but with the advent of the near-global SRTM elevation data planners can better predict which areas are in the most danger and help develop mitigation plans in the event of particular flood events. Sri Lanka is shaped like a giant teardrop falling from the southern tip of the vast Indian subcontinent. It is separated from India by the 50km (31mi) wide Palk Strait, although there is a series of stepping-stone coral islets known as Adam's Bridge that almost form a land bridge between the two countries. The island is just 350km (217mi) long and only 180km (112mi) wide at its broadest, and is about the same size as Ireland, West Virginia or Tasmania. The southern half of the island is dominated by beautiful and rugged hill country, and includes Mt Pidurutalagala, the islandaE(TM)s highest point at 2524 meters (8281 ft). The entire northern half comprises a large plain extending from the edge of the hill country to the

  16. Some parameterization formulae for mixing height compared with joint sodar and lidar observations

    Energy Technology Data Exchange (ETDEWEB)

    Bielak, A.; Burzynski, J.; Kaszowski, W.; Walczewski, J. [Inst. for Meteorology and Water Management, Cracow (Poland)

    1997-10-01

    The mixing height (MH) is most frequently defined in terms of the mixing mechanism: atmospheric turbulence and its variability versus height. From the practical point of view it is more important to know the height of mixing of real polluting substances, than the absolute ceiling of turbulent processes. This approach is followed by many authors, especially those using lidars for observations of aerosol or gas mixing. In this paper effort is made to bring some contribution to these studies. The paper presents the results of selected observations of aerosol mixing height, compared with sodar observations of BL structure and with the MH calculated with use of different formulae taken from literature. All measurements were made in Cracow, Poland. (LN) 20 refs.

  17. Message valence, familiarity, sex, and personality effects on the perceptual distortion of height.

    Science.gov (United States)

    Hensley, W E; Angoli, M

    1980-03-01

    The perceptual distortion of height was examined in a group of American male and female college student volunteers (n = 139). A message which announced either good or bad news was delivered by a familiar or unfamiliar person who was either male or female. After hearing the message, the students were asked to estimate the height of the communicator. Additionally, the variables of self-esteem and independence of judgment were measured. Results indicated that familiarity with the message source (p less than .0025) as well as sex of the communicator (p less than .024) were predictors of the perceptual distortion of height, but message valence was not. Neither self-esteem nor independence of judgment was functionally related to the proclivity to distort the heights of the communicators.

  18. Programs to obtain vertical heights from mean sea level and for computing volume of sand/mineral along beaches:A case study with Kalbadevi beach profiling data and results.

    Digital Repository Service at National Institute of Oceanography (India)

    Ganesan, P.

    vertical heights along profiles from M.S.L.? is given below: The reduced level over the bench mark pillar (BP:1 in this case, from where the profile starts) should be added with the first staff reading taken over it, which forms the height... of collimation (H.C.) of the instrument. From this H.C., all the successive staff readings (taken at regular distance interval, along the profile) should be deducted to get the vertical heights (called reduced level (R.L.) in survey terms). i) R...

  19. A Review of Spectral Methods for Variable Amplitude Fatigue Prediction and New Results

    Science.gov (United States)

    Larsen, Curtis E.; Irvine, Tom

    2013-01-01

    A comprehensive review of the available methods for estimating fatigue damage from variable amplitude loading is presented. The dependence of fatigue damage accumulation on power spectral density (psd) is investigated for random processes relevant to real structures such as in offshore or aerospace applications. Beginning with the Rayleigh (or narrow band) approximation, attempts at improved approximations or corrections to the Rayleigh approximation are examined by comparison to rainflow analysis of time histories simulated from psd functions representative of simple theoretical and real world applications. Spectral methods investigated include corrections by Wirsching and Light, Ortiz and Chen, the Dirlik formula, and the Single-Moment method, among other more recent proposed methods. Good agreement is obtained between the spectral methods and the time-domain rainflow identification for most cases, with some limitations. Guidelines are given for using the several spectral methods to increase confidence in the damage estimate.

  20. IInvestigations of space-time variability of the sea level in the Barents Sea and the White Sea by satellite altimetry data and results of hydrodynamic modelling

    Science.gov (United States)

    Lebedev, S. A.; Zilberstein, O. I.; Popov, S. K.; Tikhonova, O. V.

    2003-04-01

    The problem of retrieving of the sea level anomalies in the Barents and White Seas from satellite can be considered as two different problems. The first one is to calculate the anomalies of sea level along the trek taking into account all amendments including tidal heights. The second one is to obtain of fields of the sea level anomalies on the grid over one cycle of the exact repeat altimetry mission. Experience results show that there is preferable to use the regional tidal model for calculating tidal heights. To construct of the anomalies fields of the sea level during the exact repeat mission (cycle 35 days for ERS-1 and ERS-2), when a density of the coverage of the area of water of the Barents and White Seas by satellite measurements achieves maximum. It is necessary to solve the problem of the error minimum. This error is based by the temporal difference of the measurements over one cycle and by the specific of the hydrodynamic regime of the both seas (tidal, storm surge variations, tidal currents). To solve this problem it is assumed to use the results of the hydrodynamic modeling. The error minimum is preformed by the regression of the model results and satellite measurements. As a version it is considered the possibility of the utilizing of the neuronet obtained by the model results to construct maps of the sea level anomalies. The comparison of the model results and the calculation of the satellite altimetry variability of the sea level of Barents and White Seas shows a good coincidence between them. The satellite altimetry data of ERS-1/2 and TOPEX/POSEIDON of Ocean Altimeter Pathfinder Project (NASA/GSFC) has been used in this study. Results of the regional tidal model computations and three dimensional baroclinic model created in the Hydrometeocenter have been used as well. This study also exploited the atmosphere date of the Project REANALYSIS. The research was undertaken with partial support from the Russian Basic Research Foundation (Project No. 01-07-90106).

  1. Factors influencing the height of Hawaiian lava fountains: implications for the use of fountain height as an indicator of magma gas content

    Science.gov (United States)

    Parfitt, E.A.; Wilson, L.; Neal, C.A.

    1995-01-01

    The heights of lava fountains formed in Hawaiian-style eruptions are controlled by magma gas content, volume flux and the amounts of lava re-entrainment and gas bubble coalescence. Theoretical models of lava fountaining are used to analyse data on lava fountain height variations collected during the 1983-1986 Pu'u 'O'o vent of Kilauea volcano, Hawaii. The results show that the variable fountain heights can be largely explained by the impact of variations in volume flux and amount of lava re-entrainment on erupting magmas with a constant gas content of ???0.32 wt.% H2O. However, the gas content of the magma apparently declined by ???0.05 wt.% during the last 10 episodes of the eruption series and this decline is attributed to more extensive pre-eruption degassing due to a shallowing of the sub-vent feeder dike. It is concluded that variations in lava fountain height cannot be simply interpreted as variations in gas content, as has previously been suggested, but that fountain height can still be a useful guide to minimum gas contents. Where sufficient data are available on eruptive volume fluxes and extent of lava entrainment, greatly improved estimates can be made of magma gas content from lava fountain height. ?? 1995 Springer-Verlag.

  2. Vegetation Variability And Its Effect On Monsoon Rainfall Over South East Asia: Observational and Modeling Results

    Science.gov (United States)

    Sarkar, S.; Peters-Lidard, C.; Chiu, L.; Kafatos, M.

    2005-12-01

    Increasing population and urbanization have created stress on developing nations. The quickly shifting patterns of vegetation change in different parts of the world have given rise to the pertinent question of feedback on the climate prevailing on local to regional scales. It is now known with some certainty, that vegetation changes can affect the climate by influencing the heat and water balance. The hydrological cycle particularly is susceptible to changes in vegetation. The Monsoon rainfall forms a vital link in the hydrological cycle prevailing over South East Asia This work examines the variability of vegetation over South East Asia and assesses its impact on the monsoon rainfall. We explain the role of changing vegetation and show how this change has affected the heat and energy balance. We demonstrate the role of vegetation one season earlier in influencing rainfall intensity over specific areas in South East Asia and show the ramification of vegetation change on the summer rainfall behavior. The vegetation variability study specifically focuses on India and China, two of the largest and most populous nations. We have done an assessment to find out the key meteorological and human induced parameters affecting vegetation over the study area through a spatial analysis of monthly NDVI values. This study highlights the role of monsoon rainfall, regional climate dynamics and large scale human induced pollution to be the crucial factors governing the vegetation and vegetation distribution. The vegetation is seen to follow distinct spatial patterns that have been found to be crucial in its eventual impact on monsoon rainfall. We have carried out a series of sensitivity experiments using a land surface hydrologic modeling scheme. The vital energy and water balance parameters are identified and the daily climatological cycles are examined for possible change in behavior for different boundary conditions. It is found that the change from native deciduous forest

  3. Variability in wave refraction and resultant nearshore current patterns: Exposed versus sheltered beaches along north Karnataka, west coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Veerayya, M.; Pankajakshan, T.

    of wave heights in headland-bays and at river mouths. Certain stretches of open ocean beaches located on either side of the Kali River and the headland-bay beaches south of Karwar Head experience relatively higher wave heights for W and WSW waves...

  4. Soft computing methods for geoidal height transformation

    Science.gov (United States)

    Akyilmaz, O.; Özlüdemir, M. T.; Ayan, T.; Çelik, R. N.

    2009-07-01

    Soft computing techniques, such as fuzzy logic and artificial neural network (ANN) approaches, have enabled researchers to create precise models for use in many scientific and engineering applications. Applications that can be employed in geodetic studies include the estimation of earth rotation parameters and the determination of mean sea level changes. Another important field of geodesy in which these computing techniques can be applied is geoidal height transformation. We report here our use of a conventional polynomial model, the Adaptive Network-based Fuzzy (or in some publications, Adaptive Neuro-Fuzzy) Inference System (ANFIS), an ANN and a modified ANN approach to approximate geoid heights. These approximation models have been tested on a number of test points. The results obtained through the transformation processes from ellipsoidal heights into local levelling heights have also been compared.

  5. Atmospheric 14C changes resulting from fossil fuel CO2 release and cosmic ray flux variability

    International Nuclear Information System (INIS)

    Stuiver, M.; Quay, P.D.

    1981-01-01

    A high-precision tree-ring record of the atmospheric 14 C levels between 1820 and 1954 is presented. Good agreement is obtained between measured and model calculated 19th and 20th century atmospheric δ 14 C levels when both fossil fuel CO 2 release and predicted natural variations in 14 C production are taken into account. The best fit is obtained by using a box-diffusion model with an oceanic eddy diffusion coefficient of 3 cm 2 /s, a CO 2 atmosphere-ocean gas exchange rate of 21 moles msup(-2) yrsup(-1) and biospheric residence time of 60 years. For trees in the state of Washington the measured 1949-1951 atmospheric δ 14 C level was 20.0 +- 1.2per mille below the 1855-1864 level. Model calculations indicate that in 1950 industrial CO 2 emissions are responsible for at least 85% of the δ 14 C decline, whereas natural variability accounts for the remaining 15%. (orig.)

  6. Operation results of Wertheim-Meig. Analysis of some variables (1989-2009.

    Directory of Open Access Journals (Sweden)

    Rafael E. Pérez Castro

    2011-06-01

    Full Text Available A retrospective cross-sectional study was made to 63 patients operated with the surgical technique Wertheim-Meig having cervical cancer in stage I (1A2 and 1b1 during the corresponding period to the decade (1989-2009 in the University General Hospital Camilo Cienfuegos, with the objective to determine some factors associated to this pathology , so as the morbidity of this technique. The studied group was conformed by 63 patients who had the inclusion requirements taking into consideration the stages (t1a2, T1b1 from the total of patients having a cervical cancer. The HC was checked in a retrospective way collecting variables in a form such as: age groups, clinical stage, complications and survival, arriving to the following conclusions: the highest incidence of cervical cancer was in third decade of life (31 to 40 years. As a risk factor was: having sex at 17 years old or less than this age. It was very significant. Postoperative complications were minimum. It was found a 92% of survival, 2 recurrence (3.1%, 4 deaths (6.3% and a free interval diseases of 93.6%.

  7. Relationship between leukoaraiosis, carotid intima-media thickness and intima-media thickness variability: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Lucatelli, Pierleone [University of Rome la Sapienza, Department of Radiology, Rome (Italy); Raz, Eytan [New York University Langone Medical Center, Department of Radiology, New York, NY (United States); Saba, Luca [Azienda Ospedaliero Universitaria, Department of Radiology, di Cagliari - Polo di Monserrato, Cagliari (Italy); Argiolas, Giovanni Maria; Siotto, Paolo [Azienda Ospedaliera Brotzu, Department of Radiology, Cagliari (Italy); Montisci, Roberto [Azienda Ospedaliero Universitaria, Department of Vascular Surgery, di Cagliari - Polo di Monserrato, Cagliari (Italy); Wintermark, Max [University of Virginia, Department of Radiology, Neuroradiology Division, 1215 Lee Street-New Hospital, PO Box 800170, Charlottesville, VA (United States); King, Kevin S. [University of Texas Southwestern Medical Center, Department of Radiology, Dallas, TX (United States); Molinari, Filippo [Politecnico di Torino, Biolab, Department of Electronics, Torino (Italy); Ikeda, Nobutaka [Toho University Ohashi Medical Center, Division of Cardiovascular Medicine, Tokyo (Japan); Suri, Jasjit S. [AtheroPoint trademark LLC, Diagnostic and Monitoring Division, Roseville, CA (United States); University of Idaho, Department of Electrical Engineering, Pocatello, ID (United States)

    2016-12-15

    To assess the relationship between the degree of leukoaraiosis (LA), carotid intima-media thickness (IMT) and intima-media thickness variability (IMTV). Sixty-one consecutive patients, who underwent a brain MRI examination and a carotid artery ultrasound, were included in this retrospective study, which conformed with the Declaration of Helsinki. Written informed consent was waived. In each patient, right/left carotid arteries and brain hemispheres were assessed using automated software for IMT, IMTV and LA volume. The mean hemispheric LA volume was 2,224 mm{sup 3} (SD 2,702 mm{sup 3}) and there was no statistically significant difference in LA volume between the right and left hemispheres (p value = 0.628). The mean IMT and IMTV values were 0.866 mm (SD 0.170) and 0.143 mm (SD 0.100), respectively, without significant differences between the right and left sides (p values 0.733 and 0.098, respectively). The correlation coefficient between IMTV and LA volume was 0.41 (p value = 0.0001), and 0.246 (p value = 0.074) between IMT and LA volume. IMTV significantly correlates with LA volume. Further studies are warranted to verify whether this parameter can be used clinically as a marker of cerebrovascular risk. (orig.)

  8. Variability in results from negative binomial models for Lyme disease measured at different spatial scales.

    Science.gov (United States)

    Tran, Phoebe; Waller, Lance

    2015-01-01

    Lyme disease has been the subject of many studies due to increasing incidence rates year after year and the severe complications that can arise in later stages of the disease. Negative binomial models have been used to model Lyme disease in the past with some success. However, there has been little focus on the reliability and consistency of these models when they are used to study Lyme disease at multiple spatial scales. This study seeks to explore how sensitive/consistent negative binomial models are when they are used to study Lyme disease at different spatial scales (at the regional and sub-regional levels). The study area includes the thirteen states in the Northeastern United States with the highest Lyme disease incidence during the 2002-2006 period. Lyme disease incidence at county level for the period of 2002-2006 was linked with several previously identified key landscape and climatic variables in a negative binomial regression model for the Northeastern region and two smaller sub-regions (the New England sub-region and the Mid-Atlantic sub-region). This study found that negative binomial models, indeed, were sensitive/inconsistent when used at different spatial scales. We discuss various plausible explanations for such behavior of negative binomial models. Further investigation of the inconsistency and sensitivity of negative binomial models when used at different spatial scales is important for not only future Lyme disease studies and Lyme disease risk assessment/management but any study that requires use of this model type in a spatial context. Copyright © 2014 Elsevier Inc. All rights reserved.

  9. On the Flame Height Definition for Upward Flame Spread

    OpenAIRE

    Consalvi, Jean L; Pizzo, Yannick; Porterie, Bernard; Torero, Jose L

    2007-01-01

    Flame height is defined by the experimentalists as the average position of the luminous flame and, consequently is not directly linked with a quantitative value of a physical parameter. To determine flame heights from both numerical and theoretical results, a more quantifiable criterion is needed to define flame heights and must be in agreement with the experiments to allow comparisons. For wall flames, steady wall flame experiments revealed that flame height may be define...

  10. ESTIMATION OF STAND HEIGHT AND FOREST VOLUME USING HIGH RESOLUTION STEREO PHOTOGRAPHY AND FOREST TYPE MAP

    Directory of Open Access Journals (Sweden)

    K. M. Kim

    2016-06-01

    Full Text Available Traditional field methods for measuring tree heights are often too costly and time consuming. An alternative remote sensing approach is to measure tree heights from digital stereo photographs which is more practical for forest managers and less expensive than LiDAR or synthetic aperture radar. This work proposes an estimation of stand height and forest volume(m3/ha using normalized digital surface model (nDSM from high resolution stereo photography (25cm resolution and forest type map. The study area was located in Mt. Maehwa model forest in Hong Chun-Gun, South Korea. The forest type map has four attributes such as major species, age class, DBH class and crown density class by stand. Overlapping aerial photos were taken in September 2013 and digital surface model (DSM was created by photogrammetric methods(aerial triangulation, digital image matching. Then, digital terrain model (DTM was created by filtering DSM and subtracted DTM from DSM pixel by pixel, resulting in nDSM which represents object heights (buildings, trees, etc.. Two independent variables from nDSM were used to estimate forest stand volume: crown density (% and stand height (m. First, crown density was calculated using canopy segmentation method considering live crown ratio. Next, stand height was produced by averaging individual tree heights in a stand using Esri’s ArcGIS and the USDA Forest Service’s FUSION software. Finally, stand volume was estimated and mapped using aerial photo stand volume equations by species which have two independent variables, crown density and stand height. South Korea has a historical imagery archive which can show forest change in 40 years of successful forest rehabilitation. For a future study, forest volume change map (1970s–present will be produced using this stand volume estimation method and a historical imagery archive.

  11. More practical critical height sampling.

    Science.gov (United States)

    Thomas B. Lynch; Jeffrey H. Gove

    2015-01-01

    Critical Height Sampling (CHS) (Kitamura 1964) can be used to predict cubic volumes per acre without using volume tables or equations. The critical height is defined as the height at which the tree stem appears to be in borderline condition using the point-sampling angle gauge (e.g. prism). An estimate of cubic volume per acre can be obtained from multiplication of the...

  12. Height-Deterministic Pushdown Automata

    DEFF Research Database (Denmark)

    Nowotka, Dirk; Srba, Jiri

    2007-01-01

    We define the notion of height-deterministic pushdown automata, a model where for any given input string the stack heights during any (nondeterministic) computation on the input are a priori fixed. Different subclasses of height-deterministic pushdown automata, strictly containing the class...... of regular languages and still closed under boolean language operations, are considered. Several of such language classes have been described in the literature. Here, we suggest a natural and intuitive model that subsumes all the formalisms proposed so far by employing height-deterministic pushdown automata...

  13. Unified height systems after GOCE

    Science.gov (United States)

    Rummel, Reiner; Gruber, Thomas; Sideris, Michael; Rangelova, Elena; Woodworth, Phil; Hughes, Chris; Ihde, Johannes; Liebsch, Gunter; Rülke, Axel; Gerlach, Christian; Haagmans, Roger

    2015-04-01

    The objectives of global height unification are twofold, (1) the realization of accurate geopotential numbers C together with their standard deviation σ(C) at a selected set of stations (datum points of national height systems, geodetic fundamental stations (IERS), primary tide gauges (PSMSL) and primary reference clocks (IERS)) and (2) the determination of height off-sets between all existing regional/national height systems and one global height reference. In the future the primary method of height determination will be GPS-levelling with very stringent requirements concerning the consistency of the positioning and the gravity potential difference part. Consistency is required in terms of the applied standards (ITRF, zero tide system, geodetic reference system). Geopotential differences will be based on a next generation geopotential model combining GOCE and GRACE and a best possible collection of global terrestrial and altimetric gravity and topographic data. Ultimately, the envisaged accuracy of height unification is about 10 cm2/s2 (or 1cm). At the moment, in well surveyed regions, an accuracy of about 40 to 60 cm2/s2 (or 4 to 6cm) is attainable. Objective One can be realized by straight forward computation of geopotential numbers C, i.e. geopotential differences relative to an adopted height reference. No adjustment is required for this. Objective Two, the unification of existing height systems is achieved by employing a least-squares adjustment based on the GBVP-approach. In order to attain a non-singular solution, this requires for each included datum zone at least one geo-referenced station per zone, i.e. its ellipsoidal height h and, in addition, the corresponding physical height H (geopotential number, normal height, orthometric height, etc.). Changes in geopotential numbers of consecutive realizations reflect (1) temporal changes of station heights, (2) improvements or changes of the applied geopotential (or geoid) model and (3) improvements of the

  14. Agreement between measured height, and height predicted from ...

    African Journals Online (AJOL)

    lower limb measurements, such as knee height, as well as upper limb measures ... had with bone injuries/fractures affecting height or ulna length; and n = 1 had a ... and heels, buttocks and upper back in contact with the vertical surface of the .... found striking similarity in linear growth of infants to five-year- olds among all ...

  15. Challenges in Defining Tsunami Wave Height

    Science.gov (United States)

    Stroker, K. J.; Dunbar, P. K.; Mungov, G.; Sweeney, A.; Arcos, N. P.

    2017-12-01

    The NOAA National Centers for Environmental Information (NCEI) and co-located World Data Service for Geophysics maintain the global tsunami archive consisting of the historical tsunami database, imagery, and raw and processed water level data. The historical tsunami database incorporates, where available, maximum wave heights for each coastal tide gauge and deep-ocean buoy that recorded a tsunami signal. These data are important because they are used for tsunami hazard assessment, model calibration, validation, and forecast and warning. There have been ongoing discussions in the tsunami community about the correct way to measure and report these wave heights. It is important to understand how these measurements might vary depending on how the data were processed and the definition of maximum wave height. On September 16, 2015, an 8.3 Mw earthquake located 48 km west of Illapel, Chile generated a tsunami that was observed all over the Pacific region. We processed the time-series water level data for 57 tide gauges that recorded this tsunami and compared the maximum wave heights determined from different definitions. We also compared the maximum wave heights from the NCEI-processed data with the heights reported by the NOAA Tsunami Warning Centers. We found that in the near field different methods of determining the maximum tsunami wave heights could result in large differences due to possible instrumental clipping. We also found that the maximum peak is usually larger than the maximum amplitude (½ peak-to-trough), but the differences for the majority of the stations were Warning Centers. Since there is currently only one field in the NCEI historical tsunami database to store the maximum tsunami wave height, NCEI will consider adding an additional field for the maximum peak measurement.

  16. A search for β Cephei variable stars in the Magellanic Clouds: motivation and first results for the LMC

    International Nuclear Information System (INIS)

    Sterken, C.; Jerzykiewicz, M.

    1988-01-01

    Motivation for starting a programme of detecting and investigating β Cephei variables in the Magellanic Clouds is given. Differential photoelectric observations are then reported of six LMC stars which fall in the instability strip defined by the galactic β Cephei variables. Three programme stars are found to exhibit short-term brightness variations. One of them, showing a sinusoidal light-curve with an amplitude (half-range) equal to 0.0070 ± 0.0011 mag and a period equal to about 5 hr, is a promising β Cephei candidate. In the case of the other two variable programme stars, the interpretation of the results is less straightforward. The remaining three programme stars are shown to be constant on a short time-scale, two to within ± 0.010 mag, and one to within ± 0.005 magn. (author)

  17. Estimation of spatial variability of lignite mine dumping ground soil properties using CPTu results

    Directory of Open Access Journals (Sweden)

    Bagińska Irena

    2016-03-01

    Full Text Available The paper deals with application of CPTu test results for the probabilistic modeling of dumping grounds. The statistical measures use results from 42 CPT test points located in the lignite mine dumping ground from the region of Central Europe. Both the tip resistance qc as well as local friction fs are tested. Based on the mean values and standard deviations of measured quantities the specific zones in the dumping site profile are distinguished. For three main zones standard deviations of linearly de-trended functions, distributions of normalized de-trended values for qc and fs are examined. Also the vertical scales of fluctuation for both measured quantities are estimated. The obtained result shows that lignite mine dumping site can be successfully described with the Random Field Theory. Additional use of fs values introduces supplementary statistical information.

  18. Association between Serum Uric Acid Levels and Sleep Variables: Results from the National Health and Nutrition Survey 2005–2008

    Directory of Open Access Journals (Sweden)

    R. Constance Wiener

    2012-01-01

    Full Text Available Sleep disordered breathing as well as high serum uric acid levels are independent risk factors for cardiovascular disease. However, studies evaluating the relationship between sleep-disordered breathing and hyperuricemia are limited. We examined the 2005–2008 National Health and Nutrition Examination survey's sleep variables and high serum uric acid among 6491 participants aged ≥20 years. The sleep variables included sleep duration, snoring, snorting, and daytime sleepiness. The main outcome was high serum uric acid level, defined as levels of serum uric acid >6.8 mg/dL in males and >6.0 mg/dL in females. We found that snoring more than 5 nights per week, daytime sleepiness, and an additive composite score of sleep variables were associated with high serum uric acid in the age- , sex-adjusted model and in a multivariable model adjusting for demographic and lifestyle/behavioral risk factors. The association was attenuated with the addition of variables related to clinical outcomes such as depression, diabetes, hypertension, and high-cholesterol levels. Our results indicate a positive relationship between sleep variables, including the presence of snoring, snorting, and daytime sleepiness, and high serum uric acid levels.

  19. Variable Entry Biased Paracentric Hemispherical Deflector: Experimental results on energy resolution for different entry positions

    Science.gov (United States)

    Dogan, Mevlut; Ulu, Melike; Gennerakis, Giannis; Zouros, Theo J. M.

    2014-04-01

    A new hemispherical deflector analyzer (HDA) which is designed for electron energy analysis in atomic collisions has been constructed and tested. Using the crossed beam technique at the electron spectrometer, test measurements were performed for electron beam (200 eV) - Helium atoms interactions. These first experimental results show that the paracentric entries give almost twice as good resolution as that for the conventional entry. Supporting simulations of the entire lens+HDA spectrometer are found in relatively good agreement with experiment.

  20. Mapping Forest Canopy Height over Continental China Using Multi-Source Remote Sensing Data

    Directory of Open Access Journals (Sweden)

    Xiliang Ni

    2015-06-01

    Full Text Available Spatially-detailed forest height data are useful to monitor local, regional and global carbon cycle. LiDAR remote sensing can measure three-dimensional forest features but generating spatially-contiguous forest height maps at a large scale (e.g., continental and global is problematic because existing LiDAR instruments are still data-limited and expensive. This paper proposes a new approach based on an artificial neural network (ANN for modeling of forest canopy heights over the China continent. Our model ingests spaceborne LiDAR metrics and multiple geospatial predictors including climatic variables (temperature and precipitation, forest type, tree cover percent and land surface reflectance. The spaceborne LiDAR instrument used in the study is the Geoscience Laser Altimeter System (GLAS, which can provide within-footprint forest canopy heights. The ANN was trained with pairs between spatially discrete LiDAR metrics and full gridded geo-predictors. This generates valid conjugations to predict heights over the China continent. The ANN modeled heights were evaluated with three different reference data. First, field measured tree heights from three experiment sites were used to validate the ANN model predictions. The observed tree heights at the site-scale agreed well with the modeled forest heights (R = 0.827, and RMSE = 4.15 m. Second, spatially discrete GLAS observations and a continuous map from the interpolation of GLAS-derived tree heights were separately used to evaluate the ANN model. We obtained R of 0.725 and RMSE of 7.86 m and R of 0.759 and RMSE of 8.85 m, respectively. Further, inter-comparisons were also performed with two existing forest height maps. Our model granted a moderate agreement with the existing satellite-based forest height maps (R = 0.738, and RMSE = 7.65 m (R2 = 0.52, and RMSE = 8.99 m. Our results showed that the ANN model developed in this paper is capable of estimating forest heights over the China continent with a

  1. The genetic variability of the Podolica cattle breed from the Gargano area. Preliminary results

    Directory of Open Access Journals (Sweden)

    Dario Cianci

    2010-01-01

    Full Text Available The Podolica cattle breed is autochthonous of Southern Italy and denoted by its particular rusticity. This study presents the preliminary results of the genetic characterization of the Podolica breed using DNA STR markers. A total of 20 microsatellite loci were analysed in 79 individuals reared in the Gargano area. Number of polymorphisms, allele fre- quencies, deviations from Hardy-Weinberg proportions, linkage disequilibrium between loci and genetic similarities between animals were calculated. The results showed a high deficiency of heterozygotes, the observed mean of het- erozygosis being 0.449, whereas the expected mean was 0.766. Many markers showed also deviations from the Hardy- Weinberg proportions and significant linkage disequilibrium between loci. However the genetic similarity within the pop- ulation was low (0.281 and the average number of alleles per locus was high (10, representing a high genetic vari- ability. In order to explain these results, a stratification of the breed in sub-populations with a high interior genetic homo- geneity but markedly differentiated one from each other could be hypothesized; this situation probably derived from non- random mating within each herd (consanguinity and from the lack of exchange of genetic material between the herds. A further study is needed on a wider sample and extending the analysis to FAO-ISAG microsatellite panel in order to con- firm this hypothesis. This could eventually provide the information necessary for the correct management of the repro- ductive schemes and for genomic traceability of meat production.

  2. Variable infiltration and river flooding resulting in changing groundwater quality - A case study from Central Europe

    Science.gov (United States)

    Miotliński, Konrad; Postma, Dieke; Kowalczyk, Andrzej

    2012-01-01

    SummaryThe changes in groundwater quality occurring in a buried valley aquifer following a reduction in groundwater exploitation and enhanced infiltration due to extensive flooding of the Odra River in 1997 were investigated. Long-time series data for the chemical composition of groundwater in a large well field for drinking water supply indicated the deterioration of groundwater quality in the wells capturing water from the flooded area, which had been intensively cultivated since the 1960s. Infiltration of flooded river water into the aquifer is suggested by an elevated chloride concentration, although salt flushing from the rewatered unsaturated zone due to the enhanced recharge event is much more feasible. Concomitantly with chloride increases in the concentrations of sulphate, ferrous iron, manganese, and nickel imply the oxidation of pyrite (FeS 2) which is abundant in the aquifer. The proton production resulting from pyrite oxidation is buffered by the dissolution of calcite, while the Ca:SO 4 stoichiometry of the groundwater indicates that pyrite oxidation coupled with nitrate reduction is the dominant process occurring in the aquifer. The pyritic origin of SO42- is confirmed by the sulphur isotopic composition. The resultant Fe 2+ increase induces Mn-oxide dissolution and the mobilisation of Ni 2+ previously adsorbed to Mn-oxide surfaces. The study has a major implication for groundwater quality prediction studies where there are considerable variations in water level associated with groundwater management and climate change issues.

  3. Fulfilling the law of a single independent variable and improving the result of mathematical educational research

    Science.gov (United States)

    Pardimin, H.; Arcana, N.

    2018-01-01

    Many types of research in the field of mathematics education apply the Quasi-Experimental method and statistical analysis use t-test. Quasi-experiment has a weakness that is difficult to fulfil “the law of a single independent variable”. T-test also has a weakness that is a generalization of the conclusions obtained is less powerful. This research aimed to find ways to reduce the weaknesses of the Quasi-experimental method and improved the generalization of the research results. The method applied in the research was a non-interactive qualitative method, and the type was concept analysis. Concepts analysed are the concept of statistics, research methods of education, and research reports. The result represented a way to overcome the weaknesses of quasi-Experiments and T-test. In addition, the way was to apply a combination of Factorial Design and Balanced Design, which the authors refer to as Factorial-Balanced Design. The advantages of this design are: (1) almost fulfilling “the low of single independent variable” so no need to test the similarity of the academic ability, (2) the sample size of the experimental group and the control group became larger and equal; so it becomes robust to deal with violations of the assumptions of the ANOVA test.

  4. Intra-night Optical Variability Monitoring of Fermi Blazars: First Results from 1.3 m J. C. Bhattacharya Telescope

    Energy Technology Data Exchange (ETDEWEB)

    Paliya, Vaidehi S.; Ajello, M.; Kaur, A. [Department of Physics and Astronomy, Clemson University, Kinard Lab of Physics, Clemson, SC 29634-0978 (United States); Stalin, C. S., E-mail: vpaliya@g.clemson.edu [Indian Institute of Astrophysics, Block II, Koramangala, Bangalore-560034 (India)

    2017-07-20

    We report the first results obtained from our campaign to characterize the intra-night-optical variability (INOV) properties of Fermi detected blazars, using the observations from the recently commissioned 1.3 m J. C. Bhattacharya telescope (JCBT). During the first run, we were able to observe 17 blazars in the Bessel R filter for ∼137 hr. Using C- and scaled F -statistics, we quantify the extent of INOV and derive the duty cycle (DC), which is the fraction of time during which a source exhibits a substantial flux variability. We find a high DC of 40% for BL Lac objects and the flat spectrum radio quasars are relatively less variable (DC ∼ 15%). However, when estimated for blazars sub-classes, a high DC of ∼59% is found in low synchrotron peaked (LSP) blazars, whereas, intermediate and high synchrotron peaked objects have a low DC of ∼11% and 13%, respectively. We find evidence of the association of the high amplitude INOV with the γ -ray flaring state. We also notice a high polarization during the elevated INOV states (for the sources that have polarimetric data available), thus supporting the jet based origin of the observed variability. We plan to enlarge the sample and utilize the time availability from the small telescopes, such as 1.3 m JCBT, to strengthen/verify the results obtained in this work and those existing in the literature.

  5. Height and Tilt Geometric Texture

    DEFF Research Database (Denmark)

    Andersen, Vedrana; Desbrun, Mathieu; Bærentzen, Jakob Andreas

    2009-01-01

    compromise between functionality and simplicity: it can efficiently handle and process geometric texture too complex to be represented as a height field, without having recourse to full blown mesh editing algorithms. The height-and-tilt representation proposed here is fully intrinsic to the mesh, making...

  6. Fluctuations in Schottky barrier heights

    International Nuclear Information System (INIS)

    Mahan, G.D.

    1984-01-01

    A double Schottky barrier is often formed at the grain boundary in polycrystalline semiconductors. The barrier height is shown to fluctuate in value due to the random nature of the impurity positions. The magnitude of the fluctuations is 0.1 eV, and the fluctuations cause the barrier height measured by capacitance to differ from the one measured by electrical conductivity

  7. Planetary boundary layer height variability over athens, greece, based on the synergy of raman lidar and radiosonde data: Application of the kalman filter and other techniques (2011-2016)

    Science.gov (United States)

    Alexiou, Dimitrios; Kokkalis, Panagiotis; Papayannis, Alexandros; Rocadenbosch, Francesc; Argyrouli, Athina; Tsaknakis, Georgios; Tzanis, Chris G.

    2018-04-01

    In this paper we studied the temporal evolution of the Planetary Boundary Layer height (PBLH) over the basin of Athens, Greece during a 5-year period (2011-2016) using data from the EOLE Raman lidar system. The lidar data (range-corrected lidar signals-RCS) were selected around 12:00 UTC and 00:00 UTC for a total of 332 cases: 165 days and 167 nights. Extended Kalman filtering techniques were used for the determination of the PBLH. Moreover, several well established techniques for the PBLH estimation based on lidar data were also tested for a total of 35 cases. Comparisons with the PBLH values derived from radiosonde data were also performed. The mean PBLH over Athens was found to be of the order of 1617±324 m at 12:00 UTC and of 892±130 m at 00:00 UTC, for the period examined. The mean PBLH growth rate was found to be about 170±64 m h-1 and 90±17 m h-1, during daytime and nighttime, respectively.

  8. Differential fracture healing resulting from fixation stiffness variability. A mouse model

    International Nuclear Information System (INIS)

    Gardner, M.J.; Putnam, S.M.; Wong, A.; Streubel, P.N.; Kotiya, A.; Silva, M.J.

    2011-01-01

    The mechanisms underlying the interaction between the local mechanical environment and fracture healing are not known. We developed a mouse femoral fracture model with implants of different stiffness, and hypothesized that differential fracture healing would result. Femoral shaft fractures were created in 70 mice, and were treated with an intramedullary nail made of either tungsten (Young's modulus=410 GPa) or aluminium (Young's modulus=70 GPa). Mice were then sacrificed at 2 or 5 weeks. Fracture calluses were analyzed using standard microCT, histological, and biomechanical methods. At 2 weeks, callus volume was significantly greater in the aluminium group than in the tungsten group (61.2 vs. 40.5 mm 3 , p=0.016), yet bone volume within the calluses was no different between the groups (13.2 vs. 12.3 mm 3 ). Calluses from the tungsten group were stiffer on mechanical testing (18.7 vs. 9.7 N/mm, p=0.01). The percent cartilage in the callus was 31.6% in the aluminium group and 22.9% in the tungsten group (p=0.40). At 5 weeks, there were no differences between any of the healed femora. In this study, fracture implants of different stiffness led to different fracture healing in this mouse fracture model. Fractures treated with a stiffer implant had more advanced healing at 2 weeks, but still healed by callus formation. Although this concept has been well documented previously, this particular model could be a valuable research tool to study the healing consequences of altered fixation stiffness, which may provide insight into the pathogenesis and ideal treatment of fractures and non-unions. (author)

  9. [Inter-and intra-operator variability in the analysis of semen parameters: results from a quality control program].

    Science.gov (United States)

    Daoud, Salima; Chakroun-Feki, Nozha; Sellami, Afifa; Ammar-Keskes, Leila; Rebai, Tarek

    2016-01-01

    Semen analysis is a key part of male infertility investigation. The necessity of quality management implementation in the andrology laboratory has been recognized in order to ensure the reliability of its results. The aim of this study was to evaluate intra- and inter-individual variability in the assessment of semen parameters in our laboratory through a quality control programme. Four participants from the laboratory with different experience levels have participated in this study. Semen samples of varying quality were assessed for sperm motility, concentration and morphology and the results were used to evaluate inter-participant variability. In addition, replicates of each semen sample were analyzed to determine intra-individual variability for semen parameters analysis. The average values of inter-participant coefficients of variation for sperm motility, concentration and morphology were 12.8%, 19.8% and 48.9% respectively. The mean intra-participant coefficients of variation were, respectively, 6.9%, 12.3% and 42.7% for sperm motility, concentration and morphology. Despite some random errors of under- or overestimation, the overall results remained within the limits of acceptability for all participants. Sperm morphology assessment was particularly influenced by the participant's level of experience. The present data emphasize the need for appropriate training of the laboratory staff and for regular participation in internal quality control programmes in order to improve the reliability of laboratory results.

  10. Estimation of Airborne Lidar-Derived Tropical Forest Canopy Height Using Landsat Time Series in Cambodia

    Directory of Open Access Journals (Sweden)

    Tetsuji Ota

    2014-11-01

    Full Text Available In this study, we test and demonstrate the utility of disturbance and recovery information derived from annual Landsat time series to predict current forest vertical structure (as compared to the more common approaches, that consider a sample of airborne Lidar and single-date Landsat derived variables. Mean Canopy Height (MCH was estimated separately using single date, time series, and the combination of single date and time series variables in multiple regression and random forest (RF models. The combination of single date and time series variables, which integrate disturbance history over the entire time series, overall provided better MCH prediction than using either of the two sets of variables separately. In general, the RF models resulted in improved performance in all estimates over those using multiple regression. The lowest validation error was obtained using Landsat time series variables in a RF model (R2 = 0.75 and RMSE = 2.81 m. Combining single date and time series data was more effective when the RF model was used (opposed to multiple regression. The RMSE for RF mean canopy height prediction was reduced by 13.5% when combining the two sets of variables as compared to the 3.6% RMSE decline presented by multiple regression. This study demonstrates the value of airborne Lidar and long term Landsat observations to generate estimates of forest canopy height using the random forest algorithm.

  11. Simple overlay device for determining radial head and neck height

    International Nuclear Information System (INIS)

    Moon, Jun-Gyu; Southgate, Richard D.; Fitzsimmons, James S.; O'Driscoll, Shawn W.

    2010-01-01

    The purpose of this study was to test the hypothesis that a simple overlay device can be used on radiographs to measure radial head and neck height. Thirty anteroposterior elbow radiographs from 30 patients with a clinical diagnosis of lateral epicondylitis were examined to measure radial head and neck height. Three methods using different points along the bicipital tuberosity as a landmark were used. Method 1 used the proximal end of the bicipital tuberosity, method 2 used the most prominent point of the bicipital tuberosity, and method 3 used a simple overlay device (SOD) template that was aligned with anatomic reference points. All measurements were performed three times by three observers to determine interobserver and intraobserver reliability. Intraclass correlation coefficients revealed higher interobserver and intraobserver correlations for the SOD template method than for the other two methods. The 95% limits of agreement between observers were markedly better (-1.8 mm to +1.0 mm) for the SOD template method than for the proximal point method (-3.8 mm to +3.4 mm) or the prominent point method (-5.9 mm to +4.9 mm). We found that the SOD template method was reliable for assessing radial head and neck height. It had less variability than other methods, its 95% limit of agreement being less than 2 mm. This method could be helpful for assessing whether or not the insertion of a radial head prosthesis has resulted in over-lengthening of the radius. (orig.)

  12. Simple overlay device for determining radial head and neck height

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Jun-Gyu; Southgate, Richard D.; Fitzsimmons, James S.; O' Driscoll, Shawn W. [Mayo Clinic, Department of Orthopaedic Surgery, Rochester, MN (United States)

    2010-09-15

    The purpose of this study was to test the hypothesis that a simple overlay device can be used on radiographs to measure radial head and neck height. Thirty anteroposterior elbow radiographs from 30 patients with a clinical diagnosis of lateral epicondylitis were examined to measure radial head and neck height. Three methods using different points along the bicipital tuberosity as a landmark were used. Method 1 used the proximal end of the bicipital tuberosity, method 2 used the most prominent point of the bicipital tuberosity, and method 3 used a simple overlay device (SOD) template that was aligned with anatomic reference points. All measurements were performed three times by three observers to determine interobserver and intraobserver reliability. Intraclass correlation coefficients revealed higher interobserver and intraobserver correlations for the SOD template method than for the other two methods. The 95% limits of agreement between observers were markedly better (-1.8 mm to +1.0 mm) for the SOD template method than for the proximal point method (-3.8 mm to +3.4 mm) or the prominent point method (-5.9 mm to +4.9 mm). We found that the SOD template method was reliable for assessing radial head and neck height. It had less variability than other methods, its 95% limit of agreement being less than 2 mm. This method could be helpful for assessing whether or not the insertion of a radial head prosthesis has resulted in over-lengthening of the radius. (orig.)

  13. Incorporating shape constraints in generalized additive modelling of the height-diameter relationship for Norway spruce

    Directory of Open Access Journals (Sweden)

    Natalya Pya

    2016-02-01

    Full Text Available Background: Measurements of tree heights and diameters are essential in forest assessment and modelling. Tree heights are used for estimating timber volume, site index and other important variables related to forest growth and yield, succession and carbon budget models. However, the diameter at breast height (dbh can be more accurately obtained and at lower cost, than total tree height. Hence, generalized height-diameter (h-d models that predict tree height from dbh, age and other covariates are needed. For a more flexible but biologically plausible estimation of covariate effects we use shape constrained generalized additive models as an extension of existing h-d model approaches. We use causal site parameters such as index of aridity to enhance the generality and causality of the models and to enable predictions under projected changeable climatic conditions. Methods: We develop unconstrained generalized additive models (GAM and shape constrained generalized additive models (SCAM for investigating the possible effects of tree-specific parameters such as tree age, relative diameter at breast height, and site-specific parameters such as index of aridity and sum of daily mean temperature during vegetation period, on the h-d relationship of forests in Lower Saxony, Germany. Results: Some of the derived effects, e.g. effects of age, index of aridity and sum of daily mean temperature have significantly non-linear pattern. The need for using SCAM results from the fact that some of the model effects show partially implausible patterns especially at the boundaries of data ranges. The derived model predicts monotonically increasing levels of tree height with increasing age and temperature sum and decreasing aridity and social rank of a tree within a stand. The definition of constraints leads only to marginal or minor decline in the model statistics like AIC. An observed structured spatial trend in tree height is modelled via 2-dimensional surface

  14. Small-scale open ocean currents have large effects on wind wave heights

    Science.gov (United States)

    Ardhuin, Fabrice; Gille, Sarah T.; Menemenlis, Dimitris; Rocha, Cesar B.; Rascle, Nicolas; Chapron, Bertrand; Gula, Jonathan; Molemaker, Jeroen

    2017-06-01

    Tidal currents and large-scale oceanic currents are known to modify ocean wave properties, causing extreme sea states that are a hazard to navigation. Recent advances in the understanding and modeling capability of open ocean currents have revealed the ubiquitous presence of eddies, fronts, and filaments at scales 10-100 km. Based on realistic numerical models, we show that these structures can be the main source of variability in significant wave heights at scales less than 200 km, including important variations down to 10 km. Model results are consistent with wave height variations along satellite altimeter tracks, resolved at scales larger than 50 km. The spectrum of significant wave heights is found to be of the order of 70>>2/>(g2>>2>) times the current spectrum, where >> is the spatially averaged significant wave height, >> is the energy-averaged period, and g is the gravity acceleration. This variability induced by currents has been largely overlooked in spite of its relevance for extreme wave heights and remote sensing.Plain Language SummaryWe show that the variations in currents at scales 10 to 100 km are the main source of variations in wave heights at the same scales. Our work uses a combination of realistic numerical models for currents and waves and data from the Jason-3 and SARAL/AltiKa satellites. This finding will be of interest for the investigation of extreme wave heights, remote sensing, and air-sea interactions. As an immediate application, the present results will help constrain the error budget of the up-coming satellite missions, in particular the Surface Water and Ocean Topography (SWOT) mission, and decide how the data will have to be processed to arrive at accurate sea level and wave measurements. It will also help in the analysis of wave measurements by the CFOSAT satellite.

  15. Adult height after long-term, continuous growth hormone (GH) treatment in short children born small for gestational age: results of a randomized, double-blind, dose-response GH trial

    NARCIS (Netherlands)

    Y. van Pareren; M. Houdijk; M. Jansen (Maarten); M. Reeser; P.G.H. Mulder (Paul); A.C.S. Hokken-Koelega (Anita)

    2003-01-01

    textabstractThe GH dose-response effect of long-term continuous GH treatment on adult height (AH) was evaluated in 54 short children born small for gestational age (SGA) who were participating in a randomized, double-blind, dose-response trial. Patients were randomly and blindly

  16. Programs to obtain vertical heights from mean sea level and for computing volume of sand/mineral along beaches: A case study with Kalbadevi beach profiling data and results

    Digital Repository Service at National Institute of Oceanography (India)

    Ganesan, P.

    Two programs have been developed to process profile data, for obtaining vertical heights with respect to mean sea level (M.S.L.) and for computation of volume of heavy mineral / sand accumulation or erosion along the beaches. The final output...

  17. ESTIMATION OF HEIGHT OF EUCALYPTUS TREES WITH NEUROEVOLUTION OF AUGMENTING TOPOLOGIES (NEAT

    Directory of Open Access Journals (Sweden)

    Daniel Henrique Breda Binoti

    2018-02-01

    Full Text Available ABSTRACT The aim of this study was to evaluate the method of neuroevolution of augmenting topologies (NEAT to adjust the weights and the topology of artificial neural networks (ANNs in the estimation of tree height in a clonal population of eucalyptus, and compare with estimates obtained by a hypsometric regression model. To estimate the total tree height (Ht, the RNAs and the regression model, we used as variables a diameter of 1.3 m height (dbh and the dominant height (Hd. The RNAs were adjusted and applied to the computer system NeuroForest, varying the size of the initial population (the genetic algorithm parameter and the density of initial connections. Estimates of the total height of the trees obtained with the use of RNA and the regression model were evaluated based on the correlation coefficient, the percentage of errors scatter plot, the percentage frequency histogram of percentage errors, and the root mean square error (root mean square error - RMSE. Various settings which resulted in superior statistics to the hypsometric regression model were found. Connections had the highest correlation and the lowest RMSE% with a population size value of 300 and an initial density of 0.1 RNA. The NEAT methodology proved effective in estimating the height of trees in clonal population of eucalyptus.

  18. The height of watermelons with wall

    International Nuclear Information System (INIS)

    Feierl, Thomas

    2012-01-01

    We derive asymptotics for the moments as well as the weak limit of the height distribution of watermelons with p branches with wall. This generalizes a famous result of de Bruijn et al (1972 Graph Theory and Computing (New York: Academic) pp 15–22) on the average height of planted plane trees, and results by Fulmek (2007 Electron. J. Combin. 14 R64) and Katori et al (2008 J. Stat. Phys. 131 1067–83) on the expected value and higher moments, respectively, of the height distribution of watermelons with two branches. The asymptotics for the moments depend on the analytic behaviour of certain multidimensional Dirichlet series. In order to obtain this information, we prove a reciprocity relation satisfied by the derivatives of one of Jacobi’s theta functions, which generalizes the well-known reciprocity law for Jacobi’s theta functions. (paper)

  19. Bringing satellite winds to hub-height

    DEFF Research Database (Denmark)

    Badger, Merete; Pena Diaz, Alfredo; Bredesen, Rolv Erlend

    2012-01-01

    Satellite observations of the ocean surface can provide detailed information about the spatial wind variability over large areas. This is very valuable for the mapping of wind resources offshore where other measurements are costly and sparse. Satellite sensors operating at microwave frequencies...... measure the amount of radar backscatter from the sea surface, which is a function of the instant wind speed, wind direction, and satellite viewing geometry. A major limitation related to wind retrievals from satellite observations is that existing empirical model functions relate the radar backscatter...... to wind speed at the height 10 m only. The extrapolation of satellite wind fields to higher heights, which are more relevant for wind energy, remains a challenge which cannot be addressed by means of satellite data alone. As part of the EU-NORSEWInD project (2008-12), a hybrid method has been developed...

  20. The Impact of The Quality of Financial Statements on Local Revenue Using Examination Opinion Results as Moderating Variable

    Directory of Open Access Journals (Sweden)

    Arik - Susbiyani

    2017-02-01

    Full Text Available Abstract   This study aimed to examine the influence of the financial statements on local revenue by using the results of the examination opinion as moderating variable. The study used Legitimacy Theory to explain and analyze the relationship between variables. The population in the study was all the districts and cities in Indonesia totaling 497 county and city governments. The sampling method used in the study was judgment sampling. Samples that met the criteria of the study were 116 local governments. The analytical tool used in this research was the analysis of MRA (Moderated Regression Analysis. The results showed that the effects of the partial test of the quality of financial reports to local revenues were not significant positive effects. While the partial test results stating the influence of audit opinion on local revenue having positive effects were not significant. Other results showed that the interaction between the results of the examination opinion to the quality of financial statements was  insignificant on the quality of financial statements. In other words, the results of the examination opinions moderated (strengthened the relationship between quality of financial report on local revenue of district and city governments in Indonesia.

  1. Mexico Geoid Heights (MEXICO97)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for Mexico, and North-Central America, is the MEXICO97 geoid model. The computation used about one million terrestrial and marine gravity...

  2. Alaska Geoid Heights (GEOID96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' x 4' geoid height grid for Alaska is distributed as a GEOID96 model. The computation used 1.1 million terrestrial and marine gravity data held in the...

  3. Experiences of ZAMG on mixing height determination

    Energy Technology Data Exchange (ETDEWEB)

    Piringer, M. [Zentralanstalt fuer Meteorologie und Geodynamik, ZAMG, Vienna (Austria)

    1997-10-01

    Temperature inversions in the boundary layer occur quite often, esp. in mountainous terrain by which Austria is covered to a large extent, and can lead to enhanced pollution at the surface because the air volume available for dilution is then vertically limited. The Department of Environmental Meteorology of ZAMG therefore set up several field programs in the past to study such conditions at a variety of sites in Austria, using tethersondes and Sodars. Early investigations aimed at comparing Sodar echo profiles to the tethersonde temperature profiles to derive mixing heights from the Sodar echo structure. More recently, evolving from KONGEX, the `convective boundary layer experiment`, mixing heights calculated for Vienna by the OML model were compared to those derived from radiosonde and tethersonde potential temperature profiles. Results of these investigations will be presented, focussing on the problems when using the different methods. New efforts to derive mixing heights from data were also undertaken and are discussed separately. (au)

  4. Height, Relationship Satisfaction, Jealousy, and Mate Retention

    Directory of Open Access Journals (Sweden)

    Gayle Brewer

    2009-07-01

    Full Text Available Male height is associated with high mate value. In particular, tall men are perceived as more attractive, dominant and of a higher status than shorter rivals, resulting in a greater lifetime reproductive success. Female infidelity and relationship dissolution may therefore present a greater risk to short men. It was predicted that tall men would report greater relationship satisfaction and lower jealousy and mate retention behavior than short men. Ninety eight heterosexual men in a current romantic relationship completed a questionnaire. Both linear and quadratic relationships were found between male height and relationship satisfaction, cognitive and behavioral jealousy. Tall men reported greater relationship satisfaction and lower levels of cognitive or behavioral jealousy than short men. In addition, linear and quadratic relationships were found between male height and a number of mate retention behaviors. Tall and short men engaged in different mate retention behaviors. These findings are consistent with previous research conducted in this area detailing the greater attractiveness of tall men.

  5. Relationship Between Vertical Jump Height and Swimming Start Performance Before and After an Altitude Training Camp.

    Science.gov (United States)

    García-Ramos, Amador; Padial, Paulino; de la Fuente, Blanca; Argüelles-Cienfuegos, Javier; Bonitch-Góngora, Juan; Feriche, Belén

    2016-06-01

    This study aimed (a) to analyze the development in the squat jump height and swimming start performance after an altitude training camp, (b) to correlate the jump height and swimming start performance before and after the altitude training period, and (c) to correlate the percent change in the squat jump height with the percent change in swimming start performance. Fifteen elite male swimmers from the Spanish Junior National Team (17.1 ± 0.8 years) were tested before and after a 17-day training camp at moderate altitude. The height reached in the squat jump exercise with additional loads of 0, 25, 50, 75, and 100% of swimmers' pretest body weight and swimming start performance (time to 5, 10, and 15 m) were the dependent variables analyzed. Significant increases in the jump height (p ≤ 0.05; effect size [ES]: 0.35-0.48) and swimming start performance (p jump height before training (r = -0.56 to -0.77) and after training (r = -0.50 to -0.71). The change in the squat jump height was inversely correlated with the change in the start time at 5 m (r = -0.47), 10 m (r = -0.73), and 15 m (r = -0.62). These results suggest that altitude training can be suitable to enhance explosive performance. The correlations obtained between the squat jump height and start time in the raw and change scores confirm the relevance of having high levels of lower-body muscular power to optimize swimming start performance.

  6. A Longitudinal Study of Academic Progress Rate as a Result of Team and Institutional Variables at NCAA Division I Schools

    Science.gov (United States)

    Hale, Jimmie Edwin

    2014-01-01

    This study explained Academic Progress Rate (APR) levels and differences in APR (DAPR) with team and institutional variables. Team variables included team gender, sport profile, and squad size. Institutional variables included individual variables aggregated to the institutional level. The data analyzed in this study was derived from the National…

  7. Aircraft height estimation using 2-D radar

    CSIR Research Space (South Africa)

    Hakl, H

    2010-01-01

    Full Text Available A method to infer height information from an aircraft tracked with a single 2-D search radar is presented. The method assumes level flight in the target aircraft and a good estimate of the speed of the aircraft. The method yields good results...

  8. Impact of height and shape of building roof on air quality in urban street canyons

    Science.gov (United States)

    Yassin, Mohamed F.

    2011-09-01

    A building's roof shape and roof height play an important role in determining pollutant concentrations from vehicle emissions and its complex flow patterns within urban street canyons. The impact of the roof shape and height on wind flow and dispersion of gaseous pollutants from vehicle exhaust within urban canyons were investigated numerically using a Computational Fluid Dynamics (CFD) model. Two-dimensional flow and dispersion of gaseous pollutants were analyzed using standard κ- ɛ turbulence model, which was numerically solved based on Reynolds Averaged Navier-Stokes (RANS) equations. The diffusion fields in the urban canyons were examined with three roof heights ( Z H/ H = 0.17, 0.33 and 0.5) and five roof shapes: (1) flat-shaped roof, (2) slanted-shaped roof, (3) downwind wedge-shaped roof, (4) upwind wedge-shaped roof, and (5) trapezoid-shaped roof. The numerical model was validated against the wind tunnels results in order to optimize the turbulence model. The numerical simulations agreed reasonably with the wind tunnel results. The results obtained indicated that the pollutant concentration increased as the roof height decreases. It also decreased with the slanted and trapezoid-shaped roofs but increased with the flat-shaped roof. The pollutant concentration distributions simulated in the present work, indicated that the variability of the roof shapes and roof heights of the buildings are important factors for estimating air quality within urban canyons.

  9. Evidence of inbreeding depression on human height.

    Directory of Open Access Journals (Sweden)

    Ruth McQuillan

    Full Text Available Stature is a classical and highly heritable complex trait, with 80%-90% of variation explained by genetic factors. In recent years, genome-wide association studies (GWAS have successfully identified many common additive variants influencing human height; however, little attention has been given to the potential role of recessive genetic effects. Here, we investigated genome-wide recessive effects by an analysis of inbreeding depression on adult height in over 35,000 people from 21 different population samples. We found a highly significant inverse association between height and genome-wide homozygosity, equivalent to a height reduction of up to 3 cm in the offspring of first cousins compared with the offspring of unrelated individuals, an effect which remained after controlling for the effects of socio-economic status, an important confounder (χ(2 = 83.89, df = 1; p = 5.2 × 10(-20. There was, however, a high degree of heterogeneity among populations: whereas the direction of the effect was consistent across most population samples, the effect size differed significantly among populations. It is likely that this reflects true biological heterogeneity: whether or not an effect can be observed will depend on both the variance in homozygosity in the population and the chance inheritance of individual recessive genotypes. These results predict that multiple, rare, recessive variants influence human height. Although this exploratory work focuses on height alone, the methodology developed is generally applicable to heritable quantitative traits (QT, paving the way for an investigation into inbreeding effects, and therefore genetic architecture, on a range of QT of biomedical importance.

  10. Adult height, dietary patterns, and healthy aging.

    Science.gov (United States)

    Ma, Wenjie; Hagan, Kaitlin A; Heianza, Yoriko; Sun, Qi; Rimm, Eric B; Qi, Lu

    2017-08-01

    Background: Adult height has shown directionally diverse associations with several age-related disorders, including cardiovascular disease, cancer, decline in cognitive function, and mortality. Objective: We investigated the associations of adult height with healthy aging measured by a full spectrum of health outcomes, including incidence of chronic diseases, memory, physical functioning, and mental health, among populations who have survived to older age, and whether lifestyle factors modified such relations. Design: We included 52,135 women (mean age: 44.2 y) from the Nurses' Health Study without chronic diseases in 1980 and whose health status was available in 2012. Healthy aging was defined as being free of 11 major chronic diseases and having no reported impairment of subjective memory, physical impairment, or mental health limitations. Results: Of all eligible study participants, 6877 (13.2%) were classified as healthy agers. After adjustment for demographic and lifestyle factors, we observed an 8% (95% CI: 6%, 11%) decrease in the odds of healthy aging per SD (0.062 m) increase in height. Compared with the lowest category of height (≤1.57 m), the OR of achieving healthy aging in the highest category (≥1.70 m) was 0.80 (95% CI: 0.73, 0.87; P -trend healthy aging ( P -interaction = 0.005), and among the individual dietary factors characterizing the prudent dietary pattern, fruit and vegetable intake showed the strongest effect modification ( P -interaction = 0.01). The association of greater height with reduced odds of healthy aging appeared to be more evident among women with higher adherence to the prudent dietary pattern rich in vegetable and fruit intake. Conclusions: Greater height was associated with a modest decrease in the likelihood of healthy aging. A prudent diet rich in fruit and vegetables might modify the relation. © 2017 American Society for Nutrition.

  11. Stature estimation using the knee height measurement amongst Brazilian elderly

    OpenAIRE

    Siqueira Fogal, Aline; Franceschini, Sylvia do Carmo Castro; Eloiza Priore, Silvia; Cotta, Rosângela Minardi M.; Queiroz Ribeiro, Andreia

    2015-01-01

    Introduction: Stature is an important variable in several indices of nutritional status that are applicable to elderly persons. However, stature is difficult or impossible to measure in elderly because they are often unable to maintain the standing position. A alternative is the use of estimated height from measurements of knee height measure. Aims: This study aimed to evaluate the accuracy of the formula proposed by Chumlea et al. (1985) based on the knee of a Caucasian population to estimat...

  12. Degeneration and height of cervical discs classified from MRI compared with precise height measurements from radiographs

    Energy Technology Data Exchange (ETDEWEB)

    Kolstad, Frode [National Centre of Spinal Disorders, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway)]. E-mail: frode.kolstad@medisin.ntnu.no; Myhr, Gunnar [Department of Radiology, University Hospital of Trondheim, 7006 Trondheim (Norway); Kvistad, Kjell Arne [Department of Radiology, University Hospital of Trondheim, 7006 Trondheim (Norway); Nygaard, Oystein P. [National Centre of Spinal Disorders, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway); Leivseth, Gunnar [Department of Neuromedicine, Faculty of Medicine, Norwegian University of Science and Technology, University Hospital of Trondheim, 7006 Trondheim (Norway)

    2005-09-01

    Study design: Descriptive study comparing MRI classifications with measurements from radiographs. Objectives: 1.Define the relationship between MRI classified cervical disc degeneration and objectively measured disc height. 2.Assess the level of inter- and intra-observer errors using MRI in defining cervical disc degeneration. Summary of background data: Cervical spine degeneration has been defined radiologically by loss of disc height, decreased disc and bone marrow signal intensity and disc protrusion/herniation on MRI. The intra- and inter-observer error using MRI in defining cervical degeneration influences data interpretation. Few previous studies have addressed this source of error. The relation and time sequence between cervical disc degeneration classified by MRI and cervical disc height decrease measured from radiographs is unclear. Methods: The MRI classification of degeneration was based on nucleus signal, prolaps identification and bone marrow signal. Two neuro-radiologists evaluated the MR-images independently in a blinded fashion. The radiographic disc height measurements were done by a new computer-assisted method compensating for image distortion and permitting comparison with normal level-, age- and gender-appropriate disc height. Results/conclusions: 1.Progressing disc degeneration classified from MRI is on average significantly associated with a decrease of disc height as measured from radiographs. Within each MRI defined category of degeneration measured disc heights, however, scatter in a wide range. 2.The inter-observer agreement between two neuro-radiologists in both defining degeneration and disc height by MRI was only moderate. Studies addressing questions related to cervical disc degeneration should take this into consideration.

  13. Degeneration and height of cervical discs classified from MRI compared with precise height measurements from radiographs

    International Nuclear Information System (INIS)

    Kolstad, Frode; Myhr, Gunnar; Kvistad, Kjell Arne; Nygaard, Oystein P.; Leivseth, Gunnar

    2005-01-01

    Study design: Descriptive study comparing MRI classifications with measurements from radiographs. Objectives: 1.Define the relationship between MRI classified cervical disc degeneration and objectively measured disc height. 2.Assess the level of inter- and intra-observer errors using MRI in defining cervical disc degeneration. Summary of background data: Cervical spine degeneration has been defined radiologically by loss of disc height, decreased disc and bone marrow signal intensity and disc protrusion/herniation on MRI. The intra- and inter-observer error using MRI in defining cervical degeneration influences data interpretation. Few previous studies have addressed this source of error. The relation and time sequence between cervical disc degeneration classified by MRI and cervical disc height decrease measured from radiographs is unclear. Methods: The MRI classification of degeneration was based on nucleus signal, prolaps identification and bone marrow signal. Two neuro-radiologists evaluated the MR-images independently in a blinded fashion. The radiographic disc height measurements were done by a new computer-assisted method compensating for image distortion and permitting comparison with normal level-, age- and gender-appropriate disc height. Results/conclusions: 1.Progressing disc degeneration classified from MRI is on average significantly associated with a decrease of disc height as measured from radiographs. Within each MRI defined category of degeneration measured disc heights, however, scatter in a wide range. 2.The inter-observer agreement between two neuro-radiologists in both defining degeneration and disc height by MRI was only moderate. Studies addressing questions related to cervical disc degeneration should take this into consideration

  14. Tidal Marsh Outwelling of Dissolved Organic Matter and Resulting Temporal Variability in Coastal Water Optical and Biogeochemical Properties

    Science.gov (United States)

    Tzortziou, Maria; Neale, Patrick J.; Megonigal, J. Patrick; Butterworth, Megan; Jaffe, Rudolf; Yamashita, Youhei

    2010-01-01

    Coastal wetlands are highly dynamic environments at the land-ocean interface where human activities, short-term physical forcings and intense episodic events result in high biological and chemical variability. Long being recognized as among the most productive ecosystems in the world, tidally-influenced coastal marshes are hot spots of biogeochemical transformation and exchange. High temporal resolution observations that we performed in several marsh-estuarine systems of the Chesapeake Bay revealed significant variability in water optical and biogeochemical characteristics at hourly time scales, associated with tidally-driven hydrology. Water in the tidal creek draining each marsh was sampled every hour during several semi-diurnal tidal cycles using ISCO automated samplers. Measurements showed that water leaving the marsh during ebbing tide was consistently enriched in dissolved organic carbon (DOC), frequently by more than a factor of two, compared to water entering the marsh during flooding tide. Estimates of DOC fluxes showed a net DOC export from the marsh to the estuary during seasons of both low and high biomass of marsh vegetation. Chlorophyll amounts were typically lower in the water draining the marsh, compared to that entering the marsh during flooding tide, suggesting that marshes act as transformers of particulate to dissolved organic matter. Moreover, detailed optical and compositional analyses demonstrated that marshes are important sources of optically and chemically distinctive, relatively complex, high molecular weight, aromatic-rich and highly colored dissolved organic compounds. Compared to adjacent estuarine waters, marsh-exported colored dissolved organic matter (CDOM) was characterized by considerably stronger absorption (more than a factor of three in some cases), larger DOC-specific absorption, lower exponential spectral slope, larger fluorescence signal, lower fluorescence per unit absorbance, and higher fluorescence at visible wavelengths

  15. The effect of signal variability on the histograms of anthropomorphic channel outputs: factors resulting in non-normally distributed data

    Science.gov (United States)

    Elshahaby, Fatma E. A.; Ghaly, Michael; Jha, Abhinav K.; Frey, Eric C.

    2015-03-01

    Model Observers are widely used in medical imaging for the optimization and evaluation of instrumentation, acquisition parameters and image reconstruction and processing methods. The channelized Hotelling observer (CHO) is a commonly used model observer in nuclear medicine and has seen increasing use in other modalities. An anthropmorphic CHO consists of a set of channels that model some aspects of the human visual system and the Hotelling Observer, which is the optimal linear discriminant. The optimality of the CHO is based on the assumption that the channel outputs for data with and without the signal present have a multivariate normal distribution with equal class covariance matrices. The channel outputs result from the dot product of channel templates with input images and are thus the sum of a large number of random variables. The central limit theorem is thus often used to justify the assumption that the channel outputs are normally distributed. In this work, we aim to examine this assumption for realistically simulated nuclear medicine images when various types of signal variability are present.

  16. Life-cycle studies of biodiesel in Europe: A review addressing the variability of results and modeling issues

    International Nuclear Information System (INIS)

    Malca, Joao; Freire, Fausto

    2011-01-01

    Renewable energy sources, and particularly biofuels, are being promoted as possible solutions to address global warming and the depletion of petroleum resources. Nevertheless, significant disagreement and controversies exist regarding the actual benefits of biofuels displacing fossil fuels, as shown by a large number of life-cycle studies that have varying and sometimes contradictory conclusions. This article presents a comprehensive review of life-cycle studies of biodiesel in Europe. Studies have been compared in terms of nonrenewable primary energy requirement and GHG intensity of biodiesel. Recently published studies negate the definite and deterministic advantages for biodiesel presented in former studies. A high variability of results, particularly for biodiesel GHG intensity, with emissions ranging from 15 to 170 gCO 2 eq MJ f -1 has been observed. A detailed assessment of relevant aspects, including major assumptions, modeling choices and results, has been performed. The main causes for this high variability have been investigated, with emphasis on modeling choices. Key issues found are treatment of co-product and land use modeling, including high uncertainty associated with N 2 O and carbon emissions from cultivated soil. Furthermore, a direct correlation between how soil emissions were modeled and increasing values for calculated GHG emission has been found. A robust biodiesel life-cycle modeling has been implemented and the main sources of uncertainty have been investigated to show how uncertainty can be addressed to improve the transparency and reliability of results. Recommendations for further research work concerning the improvement of biofuel life cycle modeling are also presented. (author)

  17. Pulse height model for deuterated scintillation detectors

    International Nuclear Information System (INIS)

    Wang, Haitang; Enqvist, Andreas

    2015-01-01

    An analytical model of light pulse height distribution for finite deuterated scintillation detectors is created using the impulse approximation. Particularly, the energy distribution of a scattered neutron is calculated based on an existing collision probability scheme for general cylindrical shaped detectors considering double differential cross-sections. The light pulse height distribution is analytically and numerically calculated by convoluting collision sequences with the light output function for an EJ-315 detector from our measurements completed at Ohio University. The model provides a good description of collision histories capturing transferred neutron energy in deuterium-based scintillation materials. The resulting light pulse height distribution details pulse compositions and their corresponding contributions. It shows that probabilities of neutron collision with carbon and deuterium nuclei are comparable, however the light pulse amplitude due to collisions with carbon nuclei is small and mainly located at the lower region of the light pulse distribution axis. The model can explore those neutron interaction events that generate pulses near or below a threshold that would be imposed in measurements. A comparison is made between the light pulse height distributions given by the analytical model and measurements. It reveals a significant probability of a neutron generating a small light pulse due to collisions with carbon nuclei when compared to larger light pulse generated by collisions involving deuterium nuclei. This model is beneficial to understand responses of scintillation materials and pulse compositions, as well as nuclei information extraction from recorded pulses.

  18. A GEOMETRICAL HEIGHT SCALE FOR SUNSPOT PENUMBRAE

    International Nuclear Information System (INIS)

    Puschmann, K. G.; Ruiz Cobo, B.; MartInez Pillet, V.

    2010-01-01

    Inversions of spectropolarimetric observations of penumbral filaments deliver the stratification of different physical quantities in an optical depth scale. However, without establishing a geometrical height scale, their three-dimensional geometrical structure cannot be derived. This is crucial in understanding the correct spatial variation of physical properties in the penumbral atmosphere and to provide insights into the mechanism capable of explaining the observed penumbral brightness. The aim of this work is to determine a global geometrical height scale in the penumbra by minimizing the divergence of the magnetic field vector and the deviations from static equilibrium as imposed by a force balance equation that includes pressure gradients, gravity, and the Lorentz force. Optical depth models are derived from the inversion of spectropolarimetric data of an active region observed with the Solar Optical Telescope on board the Hinode satellite. We use a genetic algorithm to determine the boundary condition for the inference of geometrical heights. The retrieved geometrical height scale permits the evaluation of the Wilson depression at each pixel and the correlation of physical quantities at each height. Our results fit into the uncombed penumbral scenario, i.e., a penumbra composed of flux tubes with channeled mass flow and with a weaker and more horizontal magnetic field as compared with the background field. The ascending material is hotter and denser than their surroundings. We do not find evidence of overturning convection or field-free regions in the inner penumbral area analyzed. The penumbral brightness can be explained by the energy transfer of the ascending mass carried by the Evershed flow, if the physical quantities below z = -75 km are extrapolated from the results of the inversion.

  19. Simulation of ICESat-2 canopy height retrievals for different ecosystems

    Science.gov (United States)

    Neuenschwander, A. L.

    2016-12-01

    Slated for launch in late 2017 (or early 2018), the ICESat-2 satellite will provide a global distribution of geodetic measurements from a space-based laser altimeter of both the terrain surface and relative canopy heights which will provide a significant benefit to society through a variety of applications ranging from improved global digital terrain models to producing distribution of above ground vegetation structure. The ATLAS instrument designed for ICESat-2, will utilize a different technology than what is found on most laser mapping systems. The photon counting technology of the ATLAS instrument onboard ICESat-2 will record the arrival time associated with a single photon detection. That detection can occur anywhere within the vertical distribution of the reflected signal, that is, anywhere within the vertical distribution of the canopy. This uncertainty of where the photon will be returned from within the vegetation layer is referred to as the vertical sampling error. Preliminary simulation studies to estimate vertical sampling error have been conducted for several ecosystems including woodland savanna, montane conifers, temperate hardwoods, tropical forest, and boreal forest. The results from these simulations indicate that the canopy heights reported on the ATL08 data product will underestimate the top canopy height in the range of 1 - 4 m. Although simulation results indicate the ICESat-2 will underestimate top canopy height, there is, however, a strong correlation between ICESat-2 heights and relative canopy height metrics (e.g. RH75, RH90). In tropical forest, simulation results indicate the ICESat-2 height correlates strongly with RH90. Similarly, in temperate broadleaf forest, the simulated ICESat-2 heights were also strongly correlated with RH90. In boreal forest, the simulated ICESat-2 heights are strongly correlated with RH75 heights. It is hypothesized that the correlations between simulated ICESat-2 heights and canopy height metrics are a

  20. Environmental radiation monitoring results for the period 1984-95 in and around Variable Energy Cyclotron Centre, Calcutta

    International Nuclear Information System (INIS)

    Basu, A.S.; Khasnabis, B.K.; Bar, M.

    1997-04-01

    Variable Energy Cyclotron (VEC) located at Bidhan Nagar, Calcutta is being used for accelerating charged particles and does not contribute to any radioactive releases to the environment. However, it being a nuclear facility, the area surrounding the facility is being routinely monitored for background radiation exposure using thermoluminescent dosimeters. This report gives the summary of the results of the survey carried out over a period of 12 years, 1984-1995. It is observed that the general radiation background in areas far removed from the facility (up to 25 km) is higher than that existing within the boundaries of VEC centre (160±21 mR/year as against 121±20 mR/year)

  1. Investigating the relationship between tree heights derived from SIBBORK forest model and remote sensing measurements

    Science.gov (United States)

    Osmanoglu, B.; Feliciano, E. A.; Armstrong, A. H.; Sun, G.; Montesano, P.; Ranson, K.

    2017-12-01

    Tree heights are one of the most commonly used remote sensing parameters to measure biomass of a forest. In this project, we investigate the relationship between remotely sensed tree heights (e.g. G-LiHT lidar and commercially available high resolution satellite imagery, HRSI) and the SIBBORK modeled tree heights. G-LiHT is a portable, airborne imaging system that simultaneously maps the composition, structure, and function of terrestrial ecosystems using lidar, imaging spectroscopy and thermal mapping. Ground elevation and canopy height models were generated using the lidar data acquired in 2012. A digital surface model was also generated using the HRSI technique from the commercially available WorldView data in 2016. The HRSI derived height and biomass products are available at the plot (10x10m) level. For this study, we parameterized the SIBBORK individual-based gap model for Howland forest, Maine. The parameterization was calibrated using field data for the study site and results show that the simulated forest reproduces the structural complexity of Howland old growth forest, based on comparisons of key variables including, aboveground biomass, forest height and basal area. Furthermore carbon cycle and ecosystem observational capabilities will be enhanced over the next 6 years via the launch of two LiDAR (NASA's GEDI and ICESAT 2) and two SAR (NASA's ISRO NiSAR and ESA's Biomass) systems. Our aim is to present the comparison of canopy height models obtained with SIBBORK forest model and remote sensing techniques, highlighting the synergy between individual-based forest modeling and high-resolution remote sensing.

  2. Evolution of Human Body Height and Its Implications in Ergonomics

    Directory of Open Access Journals (Sweden)

    İzzet DUYAR

    2009-06-01

    Full Text Available Body height is an crucial variable in the design and production of all physical spaces, primarily in the manifacturing of clothes and means of transportation. Having such an ergonomic significance, the height of the human being has constantly changed during the course of history. There exist strong data suggesting that this change is still continue. To find out stages of evolution of human height throughout the ages up to the present will help us to illuminate the human-environment relations, and to predict the possible changes that the human height might be subjected to in the future. In view of these reasons, the changes that has occured in human height from the period at which hominids appeared until humans’ transition into settled life have been closely examined. The study was carried out on the basis of the data obtained from the earlier studies in literature. These data, when considered as a whole, reveal that the human height did not continuously increase in a linear fashion in its evolutionary path but recorded some increases and decreases at different stages. The difference between males and females (sexual dimorphism has not shown a steady decrease either; instead, it has exhibited an oscillating pattern. The modern humans as a species is not unique in terms of their height; as a matter of fact, two million years ago hominids had existed at approximately the same height as the Homo sapiens. Although the average height had shown some decrease in Homo erectus, its distribution pattern was not much different than the one observed in the modern human societies. In the findings dated to the early stages of the Upper Paleolithic Age, height showed a tendency to increase again

  3. Height, weight, and education achievement in rural Peru.

    Science.gov (United States)

    Cueto, Santiago

    2005-06-01

    The education system in Peru and many other developing countries faces several challenges, including improving education achievement and increasing education enrollment in high school. It is clear from several indicators that rural students have lower education outcomes than do urban students. In this study we used cross-sectional and longitudinal analysis to determine the relationship between height-for-age z-scores (HAZ), weight-for-age z-scores (WAZ), body-mass index (BMI), and education outcomes. The sample was composed of students from 20 elementary public schools in two rural zones in Peru. The descriptive results show that there was no association between any of the anthropometric variables and achievement (mathematics and reading comprehension) or advancing to high school without repeating a grade. However, BMI was associated with dropping out of school: children with higher BMI in 1998 were more likely to be out of school by 2001. The hierarchical multivariate analysis also showed no relationship between anthropometry and achievement at the individual level, but students with relatively higher HAZ in 1998 were more likely to be drop-outs by 2001. These results contradict prior findings that showed a positive association between anthropometric variables (especially HAZ) and education achievement. The results might be explained by the fact that the study was carried out at very poor sites, at altitudes between 3000 and 3500 meters above sea level. The scarce studies about development in high altitudes suggest that the patterns for height and weight for children and adolescents are different than at sea level. Another possible explanation has to do with the fact that in the contexts studied, children who are perceived as relatively heavier (BMI) or taller (HAZ) might be expected to be out of school and start working (in fact, this was the primary reason given by children for dropping out of school).

  4. Possible evidence for a variable fine-structure constant from QSO absorption lines: motivations, analysis and results

    Science.gov (United States)

    Murphy, M. T.; Webb, J. K.; Flambaum, V. V.; Dzuba, V. A.; Churchill, C. W.; Prochaska, J. X.; Barrow, J. D.; Wolfe, A. M.

    2001-11-01

    An experimental search for variation in the fundamental coupling constants is strongly motivated by modern high-energy physics theories. Comparison of quasar (QSO) absorption-line spectra with laboratory spectra provides a sensitive probe for variability of the fine-structure constant, α, over cosmological time-scales. We have previously developed and applied a new method providing an order-of-magnitude gain in precision over previous optical astrophysical constraints. Here we extend that work by including new quasar spectra of damped Lyman-α absorption systems. We also reanalyse our previous lower-redshift data and confirm our initial results. The constraints on α come from simultaneous fitting of absorption lines of subsets of the following species: Mgi, Mgii, Alii, Aliii, Siii, Crii, Feii, Niii and Znii. We present a detailed description of our methods and results based on an analysis of 49 quasar absorption systems (towards 28 QSOs) covering the redshift range [formmu2]0.5quote above is the raw value, not corrected for any of these systematic effects. The only significant systematic effects so far identified, if removed from our data, would lead to a more significant deviation of [formmu5]Δα/α from zero.

  5. [Analytical procedure of variable number of tandem repeats (VNTR) analysis and effective use of analysis results for tuberculosis control].

    Science.gov (United States)

    Hachisu, Yushi; Hashimoto, Ruiko; Kishida, Kazunori; Yokoyama, Eiji

    2013-12-01

    Variable number of tandem repeats (VNTR) analysis is one of the methods for molecular epidemiological studies of Mycobacterium tuberculosis. VNTR analysis is a method based on PCR, provides rapid highly reproducible results and higher strain discrimination power than the restriction fragment length polymorphism (RFLP) analysis widely used in molecular epidemiological studies of Mycobacterium tuberculosis. Genetic lineage compositions of Mycobacterium tuberculosis clinical isolates differ among the regions from where they are isolated, and allelic diversity at each locus also differs among the genetic lineages of Mycobacterium tuberculosis. Therefore, the combination of VNTR loci that can provide high discrimination capacity for analysis is not common in every region. The Japan Anti-Tuberculosis Association (JATA) 12 (15) reported a standard combination of VNTR loci for analysis in Japan, and the combination with hypervariable (HV) loci added to JATA12 (15), which has very high discrimination capacity, was also reported. From these reports, it is thought that data sharing between institutions and construction of a nationwide database will progress from now on. Using database construction of VNTR profiles, VNTR analysis has become an effective tool to trace the route of tuberculosis infection, and also helps in decision-making in the treatment course. However, in order to utilize the results of VNTR analysis effectively, it is important that each related organization cooperates closely, and analysis should be appropriately applied in the system in which accurate control and private information protection are ensured.

  6. Weight and height prediction of immobilized patients

    OpenAIRE

    Rabito,Estela Iraci; Vannucchi,Gabriela Bergamini; Suen,Vivian Marques Miguel; Castilho Neto,Laércio Lopes; Marchini,Júlio Sérgio

    2006-01-01

    OBJECTIVE: To confirm the adequacy of the formula suggested in the literature and/or to develop appropriate equations for the Brazilian population of immobilized patients based on simple anthropometric measurements. METHODS: Hospitalized patients were submitted to anthropometry and methods to estimate weight and height of bedridden patients were developed by multiple linear regression. RESULTS: Three hundred sixty eight persons were evaluated at two hospital centers and five weight-predicting...

  7. Oxygen–induced barrier height changes in aluminium – amorphous ...

    African Journals Online (AJOL)

    The results show that the application of voltage causes charge exchange between the surface states and the semiconductor leading to a change in the height of the potential barrier for electrons passing from aluminium into the a-Se films. The empirically determined values of barrier height of Al/a-Se diodes with thin and ...

  8. Stereoscopic Roadside Curb Height Measurement using V-Disparity

    DEFF Research Database (Denmark)

    Matu, Florin-Octavian; Vlaykov, Iskren; Thøgersen, Mikkel

    2014-01-01

    Managing road assets, such as roadside curbs, is one of the interests of municipalities. As an interesting application of computer vision, this paper proposes a system for automated measurement of the height of the roadside curbs. The developed system uses the spatial information available...... results show that the system can measure the height of the roadside curb with good accuracy and precision....

  9. MRI screening for silicone breast implant rupture: accuracy, inter- and intraobserver variability using explantation results as reference standard

    Energy Technology Data Exchange (ETDEWEB)

    Maijers, M.C.; Ritt, M.J.P.F. [VU University Medical Centre, Department of Plastic, Reconstructive and Hand Surgery, De Boelelaan 1117, PO Box 7057, Amsterdam (Netherlands); Niessen, F.B. [VU University Medical Centre, Department of Plastic, Reconstructive and Hand Surgery, De Boelelaan 1117, PO Box 7057, Amsterdam (Netherlands); Jan van Goyen Clinic, Department of Plastic Surgery, Amsterdam (Netherlands); Veldhuizen, J.F.H. [MRI Centre, Amsterdam (Netherlands); Manoliu, R.A. [MRI Centre, Amsterdam (Netherlands); VU University Medical Centre, Department of Radiology, Amsterdam (Netherlands)

    2014-06-15

    The recall of Poly Implant Prothese (PIP) silicone breast implants in 2010 resulted in large numbers of asymptomatic women with implants who underwent magnetic resonance imaging (MRI) screening. This study's aim was to assess the accuracy and interobserver variability of MRI screening in the detection of rupture and extracapsular silicone leakage. A prospective study included 107 women with 214 PIP implants who underwent explantation preceded by MRI. In 2013, two radiologists blinded for previous MRI findings or outcome at surgery, independently re-evaluated all MRI examinations. A structured protocol described the MRI findings. The ex vivo findings served as reference standard. In 208 of the 214 explanted prostheses, radiologists agreed independently about the condition of the implants. In five of the six cases they disagreed (2.6 %), but subsequently reached consensus. A sensitivity of 93 %, specificity of 93 %, positive predictive value of 77 % and negative predictive value of 98 % was found. The interobserver agreement was excellent (kappa value of 0.92). MRI has a high accuracy in diagnosing rupture in silicone breast implants. Considering the high kappa value of interobserver agreement, MRI appears to be a consistent diagnostic test. A simple, uniform classification, may improve communication between radiologist and plastic surgeon. (orig.)

  10. MRI screening for silicone breast implant rupture: accuracy, inter- and intraobserver variability using explantation results as reference standard

    International Nuclear Information System (INIS)

    Maijers, M.C.; Ritt, M.J.P.F.; Niessen, F.B.; Veldhuizen, J.F.H.; Manoliu, R.A.

    2014-01-01

    The recall of Poly Implant Prothese (PIP) silicone breast implants in 2010 resulted in large numbers of asymptomatic women with implants who underwent magnetic resonance imaging (MRI) screening. This study's aim was to assess the accuracy and interobserver variability of MRI screening in the detection of rupture and extracapsular silicone leakage. A prospective study included 107 women with 214 PIP implants who underwent explantation preceded by MRI. In 2013, two radiologists blinded for previous MRI findings or outcome at surgery, independently re-evaluated all MRI examinations. A structured protocol described the MRI findings. The ex vivo findings served as reference standard. In 208 of the 214 explanted prostheses, radiologists agreed independently about the condition of the implants. In five of the six cases they disagreed (2.6 %), but subsequently reached consensus. A sensitivity of 93 %, specificity of 93 %, positive predictive value of 77 % and negative predictive value of 98 % was found. The interobserver agreement was excellent (kappa value of 0.92). MRI has a high accuracy in diagnosing rupture in silicone breast implants. Considering the high kappa value of interobserver agreement, MRI appears to be a consistent diagnostic test. A simple, uniform classification, may improve communication between radiologist and plastic surgeon. (orig.)

  11. On the Extreme Wave Height Analysis

    DEFF Research Database (Denmark)

    Burcharth, H. F.; Liu, Zhou

    1994-01-01

    The determination of the design wave height is usually based on the statistical analysis of long-term extreme wave height measurements. After an introduction to the procedure of the extreme wave height analysis, the paper presents new development concerning various aspects of the extreme wave...... height analysis. Finally, the paper gives a practical example based on a data set of the hindcasted wave heights for a deep water location in the Mediterranean Sea....

  12. Height, selected genetic markers and prostate cancer risk

    DEFF Research Database (Denmark)

    Lophatananon, Artitaya; Stewart-Brown, Sarah; Kote-Jarai, Zsofia

    2017-01-01

    Background:Evidence on height and prostate cancer risk is mixed, however, recent studies with large data sets support a possible role for its association with the risk of aggressive prostate cancer.Methods:We analysed data from the PRACTICAL consortium consisting of 6207 prostate cancer cases...... and 6016 controls and a subset of high grade cases (2480 cases). We explored height, polymorphisms in genes related to growth processes as main effects and their possible interactions.Results:The results suggest that height is associated with high-grade prostate cancer risk. Men with height >180 cm...... are at a 22% increased risk as compared to men with height prostate cancer risk. The aggregate scores of the selected variants identified a significantly increased risk of overall prostate cancer...

  13. How many replicate tests do I need?$-$ Variability of cookstove performance and emissions has implications for obtaining useful results

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yungang [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Sohn, Michael D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Gadgil, Ashok J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Wang, Yilun [ISO Innovative Analytics San Francisco, CA (United States); Lask, Kathleen M. [Univ. of California, Berkeley, CA (United States). College of Engineering Applied Science and Technology Program; Kirchstetter, Thomas W. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-02-01

    Almost half of the world’s population still cooks on biomass cookstoves of poor efficiency and primitive design, such as three stone fires (TSF). Emissions from biomass cookstoves contribute to adverse health effects and climate change. A number of “improved cookstoves” with higher energy efficiency and lower emissions have been designed and promoted across the world. During the design development, and for selection of a stove for dissemination, the stove performance and emissions are commonly evaluated, communicated and compared using the arithmetic average of replicate tests made using a standardized laboratory-based test, commonly the water boiling test (WBT). However, published literature shows different WBT results reported from different laboratories for the same stove technology. Also, there is no agreement in the literature on how many replicate tests should be performed to ensure “significance” in the reported average performance. This matter has not received attention in the rapidly growing literature on stoves, and yet is crucial for estimating and communicating the performance of a stove, and for comparing the performance between stoves. We present results of statistical analyses using data from a number of replicate tests of performance and emission of the Berkeley-Darfur Stove (BDS) and the TSF under well-controlled laboratory conditions. We observed moderate variability in the test results for the TSF and BDS when measuring several characteristics. Here we focus on two as illustrative: time-to-boil and PM2.5 (particulate matter less than or equal to 2.5 micrometers in diameter) emissions. We demonstrate that interpretation of the results comparing these stoves could be misleading if only a small number of replicates had been conducted. We then describe a practical approach, useful to both stove testers and designers, to assess the number of replicates needed to obtain useful data. Caution should be exercised in attaching high credibility to

  14. Cognitive functioning in elderly people and the influence of the socio-educative variables - Results from the ELES Study

    Directory of Open Access Journals (Sweden)

    Mª Feli González

    2013-12-01

    Full Text Available Cognitive functioning changes in elderly people. The degree of decline varies across different cognitive abilities and other variables, such as educational level and life-time professional activity, can slow down this process. This study investigates the pattern of cognitive performance in people over 50 years old, taking into account the influence of educational level and profession. Research data were collected during the pilot study of the Longitudinal Aging Study in Spain (ELES in which a representative sample of non-institutionalized Spanish older people was assessed. The following cognitive variables were evaluated: general cognitive functioning, verbal memory, working memory span, visuomotor speed, and language. Differences were found in all cognitive variables in the different age groups, and according to educational level and profession. These differences remained after controlling for the age variable. Population studies provide a global perspective of cognitive performance in older people and help to identify the role of the different associated factors.

  15. Height among Women is Curvilinearly Related to Life History Strategy

    Directory of Open Access Journals (Sweden)

    Abraham P. Buunk

    2009-10-01

    Full Text Available It was hypothesized that women of medium height would show a more secure, long-term mating pattern characterized by less jealousy, less intrasexual competition and a “slower” life history strategy. In three samples of female undergraduate students clear support was found for these hypotheses. In Study 1, among 120 participants, height was curvilinearly related to well-established measures of possessive and reactive jealousy, with women of medium height being less jealous than tall as well as short women. In Study 2, among 40 participants, height was curvilinearly related to intrasexual competition, with women of medium height being less competitive towards other women than tall as well as short women. In Study 3, among 299 participants, height was curvilinearly related to the Mini-K, a well-validated measure of “slower” life history strategy, with women of medium height having a slower life history strategy than tall as well as short women. The results suggest that women of medium height tend to follow a different mating strategy than either tall or short women. Various explanations and implications of these results are discussed.

  16. Analysis of Student and School Level Variables Related to Mathematics Self-Efficacy Level Based on PISA 2012 Results for China-Shanghai, Turkey, and Greece

    Science.gov (United States)

    Usta, H. Gonca

    2016-01-01

    This study aims to analyze the student and school level variables that affect students' self-efficacy levels in mathematics in China-Shanghai, Turkey, and Greece based on PISA 2012 results. In line with this purpose, the hierarchical linear regression model (HLM) was employed. The interschool variability is estimated at approximately 17% in…

  17. Global 30m Height Above the Nearest Drainage

    Science.gov (United States)

    Donchyts, Gennadii; Winsemius, Hessel; Schellekens, Jaap; Erickson, Tyler; Gao, Hongkai; Savenije, Hubert; van de Giesen, Nick

    2016-04-01

    Variability of the Earth surface is the primary characteristics affecting the flow of surface and subsurface water. Digital elevation models, usually represented as height maps above some well-defined vertical datum, are used a lot to compute hydrologic parameters such as local flow directions, drainage area, drainage network pattern, and many others. Usually, it requires a significant effort to derive these parameters at a global scale. One hydrological characteristic introduced in the last decade is Height Above the Nearest Drainage (HAND): a digital elevation model normalized using nearest drainage. This parameter has been shown to be useful for many hydrological and more general purpose applications, such as landscape hazard mapping, landform classification, remote sensing and rainfall-runoff modeling. One of the essential characteristics of HAND is its ability to capture heterogeneities in local environments, difficult to measure or model otherwise. While many applications of HAND were published in the academic literature, no studies analyze its variability on a global scale, especially, using higher resolution DEMs, such as the new, one arc-second (approximately 30m) resolution version of SRTM. In this work, we will present the first global version of HAND computed using a mosaic of two DEMS: 30m SRTM and Viewfinderpanorama DEM (90m). The lower resolution DEM was used to cover latitudes above 60 degrees north and below 56 degrees south where SRTM is not available. We compute HAND using the unmodified version of the input DEMs to ensure consistency with the original elevation model. We have parallelized processing by generating a homogenized, equal-area version of HydroBASINS catchments. The resulting catchment boundaries were used to perform processing using 30m resolution DEM. To compute HAND, a new version of D8 local drainage directions as well as flow accumulation were calculated. The latter was used to estimate river head by incorporating fixed and

  18. Encounter Probability of Individual Wave Height

    DEFF Research Database (Denmark)

    Liu, Z.; Burcharth, H. F.

    1998-01-01

    wave height corresponding to a certain exceedence probability within a structure lifetime (encounter probability), based on the statistical analysis of long-term extreme significant wave height. Then the design individual wave height is calculated as the expected maximum individual wave height...... associated with the design significant wave height, with the assumption that the individual wave heights follow the Rayleigh distribution. However, the exceedence probability of such a design individual wave height within the structure lifetime is unknown. The paper presents a method for the determination...... of the design individual wave height corresponding to an exceedence probability within the structure lifetime, given the long-term extreme significant wave height. The method can also be applied for estimation of the number of relatively large waves for fatigue analysis of constructions....

  19. Footprint parameters as a measure of arch height.

    Science.gov (United States)

    Hawes, M R; Nachbauer, W; Sovak, D; Nigg, B M

    1992-01-01

    The human foot has frequently been categorized into arch height groups based upon analysis of footprint parameters. This study investigates the relationship between directly measured arch height and many of the footprint parameters that have been assumed to represent arch height. A total of 115 male subjects were measured and footprint parameters were calculated from digitized outlines. Correlation and regression analyses were used to determine the relationship between footprint measures and arch height. It may be concluded from the results that footprint parameters proposed in the literature (arch angle, footprint index, and arch index) and two further parameters suggested in this study (arch length index and truncated arch index) are invalid as a basis for prediction or categorization of arch height. The categorization of the human foot according to the footprint measures evaluated in this paper represent no more than indices and angles of the plantar surface of the foot itself.

  20. Measuring perceived ceiling height in a visual comparison task.

    Science.gov (United States)

    von Castell, Christoph; Hecht, Heiko; Oberfeld, Daniel

    2017-03-01

    When judging interior space, a dark ceiling is judged to be lower than a light ceiling. The method of metric judgments (e.g., on a centimetre scale) that has typically been used in such tasks may reflect a genuine perceptual effect or it may reflect a cognitively mediated impression. We employed a height-matching method in which perceived ceiling height had to be matched with an adjustable pillar, thus obtaining psychometric functions that allowed for an estimation of the point of subjective equality (PSE) and the difference limen (DL). The height-matching method developed in this paper allows for a direct visual match and does not require metric judgment. It has the added advantage of providing superior precision. Experiment 1 used ceiling heights between 2.90 m and 3.00 m. The PSE proved sensitive to slight changes in perceived ceiling height. The DL was about 3% of the physical ceiling height. Experiment 2 found similar results for lower (2.30 m to 2.50 m) and higher (3.30 m to 3.50 m) ceilings. In Experiment 3, we additionally varied ceiling lightness (light grey vs. dark grey). The height matches showed that the light ceiling appeared significantly higher than the darker ceiling. We therefore attribute the influence of ceiling lightness on perceived ceiling height to a direct perceptual rather than a cognitive effect.

  1. Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis

    NARCIS (Netherlands)

    Knijnenburg, S. L.; Raemaekers, S.; van den Berg, H.; van Dijk, I. W. E. M.; Lieverst, J. A.; van der Pal, H. J.; Jaspers, M. W. M.; Caron, H. N.; Kremer, L. C.; van Santen, H. M.

    2013-01-01

    Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of

  2. Examination of the gait pattern based on adjusting and resulting components of the stride-to-stride variability

    DEFF Research Database (Denmark)

    Laessoe, Uffe; Jensen, Niels Martin Brix; Madeleine, Pascal

    2017-01-01

    Stride-to-stride variability may be used as an indicator in the assessment of gait performance, but the evaluation of this parameter is not trivial. In the gait pattern, a deviation in one stride must be corrected within the next strides (elemental variables) to ensure a steady gait (performance .......5 to 2 strides with 0.5 stride increments. The time lag values corresponded to the following contralateral stride, the following ipsilateral stride, the second following contralateral stride and the second following ipsilateral stride....

  3. Accuracy of Jump-Mat Systems for Measuring Jump Height.

    Science.gov (United States)

    Pueo, Basilio; Lipinska, Patrycja; Jiménez-Olmedo, José M; Zmijewski, Piotr; Hopkins, Will G

    2017-08-01

    Vertical-jump tests are commonly used to evaluate lower-limb power of athletes and nonathletes. Several types of equipment are available for this purpose. To compare the error of measurement of 2 jump-mat systems (Chronojump-Boscosystem and Globus Ergo Tester) with that of a motion-capture system as a criterion and to determine the modifying effect of foot length on jump height. Thirty-one young adult men alternated 4 countermovement jumps with 4 squat jumps. Mean jump height and standard deviations representing technical error of measurement arising from each device and variability arising from the subjects themselves were estimated with a novel mixed model and evaluated via standardization and magnitude-based inference. The jump-mat systems produced nearly identical measures of jump height (differences in means and in technical errors of measurement ≤1 mm). Countermovement and squat-jump height were both 13.6 cm higher with motion capture (90% confidence limits ±0.3 cm), but this very large difference was reduced to small unclear differences when adjusted to a foot length of zero. Variability in countermovement and squat-jump height arising from the subjects was small (1.1 and 1.5 cm, respectively, 90% confidence limits ±0.3 cm); technical error of motion capture was similar in magnitude (1.7 and 1.6 cm, ±0.3 and ±0.4 cm), and that of the jump mats was similar or smaller (1.2 and 0.3 cm, ±0.5 and ±0.9 cm). The jump-mat systems provide trustworthy measurements for monitoring changes in jump height. Foot length can explain the substantially higher jump height observed with motion capture.

  4. Phase height measurements on the ionosphere

    International Nuclear Information System (INIS)

    Joyner, K.H.

    1974-01-01

    Phase height measurements have been taken on 2.5 MHz E-region reflection over two paths during the day. The two paths have equivalent vertical frequencies of 2.4 MHz and 1.8 MHz. Vertical pulse measurements on 2.4 MHz have also been recorded. Results and discussion on comparisons between these measurements are presented. Phase and amplitude measurements using 4.5 MHz O and E rays have also been taken at night, F-region reflection. In particular, spectral analysis of these results is discussed. (author)

  5. An analysis of the relationship between bodily injury severity and fall height in victims of fatal falls from height

    Directory of Open Access Journals (Sweden)

    Grzegorz Teresiński

    2017-03-01

    Full Text Available Aim of the study : One of the basic issues discussed in forensic literature regarding falls from a height is determination of fall heights and differentiation between suicidal and accidental falls. The aim of the study was to verify the usefulness of the available methods for the purposes of forensic expertises. Material and methods : The study encompassed fatalities of falls from a height whose autopsies were performed in the Department of Forensic Medicine in Lublin. Results : Similarly to other authors, the severity of injuries was assessed using the Abbreviated Injury Scale (AIS and injury severity score (ISS. The study findings demonstrated a statistically significant correlation between the fall height and the severity of injuries according to ISS and a statistically significant difference in fall heights between the groups of accidents and suicides.

  6. Predicting Teacher Value-Added Results in Non-Tested Subjects Based on Confounding Variables: A Multinomial Logistic Regression

    Science.gov (United States)

    Street, Nathan Lee

    2017-01-01

    Teacher value-added measures (VAM) are designed to provide information regarding teachers' causal impact on the academic growth of students while controlling for exogenous variables. While some researchers contend VAMs successfully and authentically measure teacher causality on learning, others suggest VAMs cannot adequately control for exogenous…

  7. Definition of Physical Height Systems for Telluric Planets and Moons

    Science.gov (United States)

    Tenzer, Robert; Foroughi, Ismael; Sjöberg, Lars E.; Bagherbandi, Mohammad; Hirt, Christian; Pitoňák, Martin

    2018-01-01

    In planetary sciences, the geodetic (geometric) heights defined with respect to the reference surface (the sphere or the ellipsoid) or with respect to the center of the planet/moon are typically used for mapping topographic surface, compilation of global topographic models, detailed mapping of potential landing sites, and other space science and engineering purposes. Nevertheless, certain applications, such as studies of gravity-driven mass movements, require the physical heights to be defined with respect to the equipotential surface. Taking the analogy with terrestrial height systems, the realization of height systems for telluric planets and moons could be done by means of defining the orthometric and geoidal heights. In this case, however, the definition of the orthometric heights in principle differs. Whereas the terrestrial geoid is described as an equipotential surface that best approximates the mean sea level, such a definition for planets/moons is irrelevant in the absence of (liquid) global oceans. A more natural choice for planets and moons is to adopt the geoidal equipotential surface that closely approximates the geometric reference surface (the sphere or the ellipsoid). In this study, we address these aspects by proposing a more accurate approach for defining the orthometric heights for telluric planets and moons from available topographic and gravity models, while adopting the average crustal density in the absence of reliable crustal density models. In particular, we discuss a proper treatment of topographic masses in the context of gravimetric geoid determination. In numerical studies, we investigate differences between the geodetic and orthometric heights, represented by the geoidal heights, on Mercury, Venus, Mars, and Moon. Our results reveal that these differences are significant. The geoidal heights on Mercury vary from - 132 to 166 m. On Venus, the geoidal heights are between - 51 and 137 m with maxima on this planet at Atla Regio and Beta

  8. A high HIV-1 strain variability in London, UK, revealed by full-genome analysis: Results from the ICONIC project

    Science.gov (United States)

    Frampton, Dan; Gallo Cassarino, Tiziano; Raffle, Jade; Hubb, Jonathan; Ferns, R. Bridget; Waters, Laura; Tong, C. Y. William; Kozlakidis, Zisis; Hayward, Andrew; Kellam, Paul; Pillay, Deenan; Clark, Duncan; Nastouli, Eleni; Leigh Brown, Andrew J.

    2018-01-01

    Background & methods The ICONIC project has developed an automated high-throughput pipeline to generate HIV nearly full-length genomes (NFLG, i.e. from gag to nef) from next-generation sequencing (NGS) data. The pipeline was applied to 420 HIV samples collected at University College London Hospitals NHS Trust and Barts Health NHS Trust (London) and sequenced using an Illumina MiSeq at the Wellcome Trust Sanger Institute (Cambridge). Consensus genomes were generated and subtyped using COMET, and unique recombinants were studied with jpHMM and SimPlot. Maximum-likelihood phylogenetic trees were constructed using RAxML to identify transmission networks using the Cluster Picker. Results The pipeline generated sequences of at least 1Kb of length (median = 7.46Kb, IQR = 4.01Kb) for 375 out of the 420 samples (89%), with 174 (46.4%) being NFLG. A total of 365 sequences (169 of them NFLG) corresponded to unique subjects and were included in the down-stream analyses. The most frequent HIV subtypes were B (n = 149, 40.8%) and C (n = 77, 21.1%) and the circulating recombinant form CRF02_AG (n = 32, 8.8%). We found 14 different CRFs (n = 66, 18.1%) and multiple URFs (n = 32, 8.8%) that involved recombination between 12 different subtypes/CRFs. The most frequent URFs were B/CRF01_AE (4 cases) and A1/D, B/C, and B/CRF02_AG (3 cases each). Most URFs (19/26, 73%) lacked breakpoints in the PR+RT pol region, rendering them undetectable if only that was sequenced. Twelve (37.5%) of the URFs could have emerged within the UK, whereas the rest were probably imported from sub-Saharan Africa, South East Asia and South America. For 2 URFs we found highly similar pol sequences circulating in the UK. We detected 31 phylogenetic clusters using the full dataset: 25 pairs (mostly subtypes B and C), 4 triplets and 2 quadruplets. Some of these were not consistent across different genes due to inter- and intra-subtype recombination. Clusters involved 70 sequences, 19.2% of the dataset. Conclusions

  9. Standardizing Scale Height Computation of Maven Ngims Neutral Data and Variations Between Exobase and Homeopause Scale Heights

    Science.gov (United States)

    Elrod, M. K.; Slipski, M.; Curry, S.; Williamson, H. N.; Benna, M.; Mahaffy, P. R.

    2017-12-01

    The MAVEN NGIMS team produces a level 3 product which includes the computation of Ar scale height an atmospheric temperatures at 200 km. In the latest version (v05_r01) this has been revised to include scale height fits for CO2, N2 O and CO. Members of the MAVEN team have used various methods to compute scale heights leading to significant variations in scale height values depending on fits and techniques within a few orbits even, occasionally, the same pass. Additionally fitting scale heights in a very stable atmosphere like the day side vs night side can have different results based on boundary conditions. Currently, most methods only compute Ar scale heights as it is most stable and reacts least with the instrument. The NGIMS team has chosen to expand these fitting techniques to include fitted scale heights for CO2, N2, CO, and O. Having compared multiple techniques, the method found to be most reliable for most conditions was determined to be a simple fit method. We have focused this to a fitting method that determines the exobase altidude of the CO2 atmosphere as a maximum altitude for the highest point for fitting, and uses the periapsis as the lowest point and then fits the altitude versus log(density). The slope of altitude vs log(density) is -1/H where H is the scale height of the atmosphere for each species. Since this is between the homeopause and the exobase, each species will have a different scale height by this point. This is being released as a new standardization for the level 3 product, with the understanding that scientists and team members will continue to compute more precise scale heights and temperatures as needed based on science and model demands. This is being released in the PDS NGIMS level 3 v05 files for August 2017. Additionally, we are examining these scale heights for variations seasonally, diurnally, and above and below the exobase. The atmosphere is significantly more stable on the dayside than on the nightside. We have also found

  10. High-Throughput Phenotyping of Plant Height: Comparing Unmanned Aerial Vehicles and Ground LiDAR Estimates.

    Science.gov (United States)

    Madec, Simon; Baret, Fred; de Solan, Benoît; Thomas, Samuel; Dutartre, Dan; Jezequel, Stéphane; Hemmerlé, Matthieu; Colombeau, Gallian; Comar, Alexis

    2017-01-01

    The capacity of LiDAR and Unmanned Aerial Vehicles (UAVs) to provide plant height estimates as a high-throughput plant phenotyping trait was explored. An experiment over wheat genotypes conducted under well watered and water stress modalities was conducted. Frequent LiDAR measurements were performed along the growth cycle using a phénomobile unmanned ground vehicle. UAV equipped with a high resolution RGB camera was flying the experiment several times to retrieve the digital surface model from structure from motion techniques. Both techniques provide a 3D dense point cloud from which the plant height can be estimated. Plant height first defined as the z -value for which 99.5% of the points of the dense cloud are below. This provides good consistency with manual measurements of plant height (RMSE = 3.5 cm) while minimizing the variability along each microplot. Results show that LiDAR and structure from motion plant height values are always consistent. However, a slight under-estimation is observed for structure from motion techniques, in relation with the coarser spatial resolution of UAV imagery and the limited penetration capacity of structure from motion as compared to LiDAR. Very high heritability values ( H 2 > 0.90) were found for both techniques when lodging was not present. The dynamics of plant height shows that it carries pertinent information regarding the period and magnitude of the plant stress. Further, the date when the maximum plant height is reached was found to be very heritable ( H 2 > 0.88) and a good proxy of the flowering stage. Finally, the capacity of plant height as a proxy for total above ground biomass and yield is discussed.

  11. Sensitivity of the urban airshed model to mixing height profiles

    Energy Technology Data Exchange (ETDEWEB)

    Rao, S.T.; Sistla, G.; Ku, J.Y.; Zhou, N.; Hao, W. [New York State Dept. of Environmental Conservation, Albany, NY (United States)

    1994-12-31

    The United States Environmental Protection Agency (USEPA) has recommended the use of the Urban Airshed Model (UAM), a grid-based photochemical model, for regulatory applications. One of the important parameters in applications of the UAM is the height of the mixed layer or the diffusion break. In this study, we examine the sensitivity of the UAM-predicted ozone concentrations to (a) a spatially invariant diurnal mixing height profile, and (b) a spatially varying diurnal mixing height profile for a high ozone episode of July 1988 for the New York Airshed. The 1985/88 emissions inventory used in the EPA`s Regional Oxidant Modeling simulations has been regridded for this study. Preliminary results suggest that the spatially varying case yields a higher peak ozone concentrations compared to the spatially invariant mixing height simulation, with differences in the peak ozone ranging from a few ppb to about 40 ppb for the days simulated. These differences are attributed to the differences in the shape of the mixing height profiles and its rate of growth during the morning hours when peak emissions are injected into the atmosphere. Examination of the impact of emissions reductions associated with these two mixing height profiles indicates that NO{sub x}-focussed controls provide a greater change in the predicted ozone peak under spatially invariant mixing heights than under the spatially varying mixing height profile. On the other hand, VOC-focussed controls provide a greater change in the predicted peak ozone levels under spatially varying mixing heights than under the spatially invariant mixing height profile.

  12. Validation of mixing heights derived from the operational NWP models at the German weather service

    Energy Technology Data Exchange (ETDEWEB)

    Fay, B.; Schrodin, R.; Jacobsen, I. [Deutscher Wetterdienst, Offenbach (Germany); Engelbart, D. [Deutscher Wetterdienst, Meteorol. Observ. Lindenberg (Germany)

    1997-10-01

    NWP models incorporate an ever-increasing number of observations via four-dimensional data assimilation and are capable of providing comprehensive information about the atmosphere both in space and time. They describe not only near surface parameters but also the vertical structure of the atmosphere. They operate daily, are well verified and successfully used as meteorological pre-processors in large-scale dispersion modelling. Applications like ozone forecasts, emission or power plant control calculations require highly resolved, reliable, and routine values of the temporal evolution of the mixing height (MH) which is a critical parameter in determining the mixing and transformation of substances and the resulting pollution levels near the ground. The purpose of development at the German Weather Service is a straightforward mixing height scheme that uses only parameters derived from NWP model variables and thus automatically provides spatial and temporal fields of mixing heights on an operational basis. An universal parameter to describe stability is the Richardson number Ri. Compared to the usual diagnostic or rate equations, the Ri number concept of determining mixing heights has the advantage of using not only surface layer parameters but also regarding the vertical structure of the boundary layer resolved in the NWP models. (au)

  13. Assessing biomass based on canopy height profiles using airborne laser scanning data in eucalypt plantations

    Directory of Open Access Journals (Sweden)

    André Gracioso Peres Silva

    2015-12-01

    Full Text Available This study aimed to map the stem biomass of an even-aged eucalyptus plantation in southeastern Brazil based on canopy height profile (CHPs statistics using wall-to-wall discrete return airborne laser scanning (ALS, and compare the results with alternative maps generated by ordinary kriging interpolation from field-derived measurements. The assessment of stem biomass with ALS data was carried out using regression analysis methods. Initially, CHPs were determined to express the distribution of laser point heights in the ALS cloud for each sample plot. The probability density function (pdf used was the Weibull distribution, with two parameters that in a secondary task, were used as explanatory variables to model stem biomass. ALS metrics such as height percentiles, dispersion of heights, and proportion of points were also investigated. A simple linear regression model of stem biomass as a function of the Weibull scale parameter showed high correlation (adj.R2 = 0.89. The alternative model considering the 30th percentile and the Weibull shape parameter slightly improved the quality of the estimation (adj.R2 = 0.93. Stem biomass maps based on the Weibull scale parameter doubled the accuracy of the ordinary kriging approach (relative root mean square error = 6 % and 13 %, respectively.

  14. Maternal Height and Child Growth Patterns

    OpenAIRE

    Addo, O. Yaw; Stein, Aryeh D.; Fall, Caroline H.; Gigante, Denise P.; Guntupalli, Aravinda M.; Horta, Bernardo L.; Kuzawa, Christopher W.; Lee, Nanette; Norris, Shane A.; Prabhakaran, Poornima; Richter, Linda M.; Sachdev, Harshpal S.; Martorell, Reynaldo

    2013-01-01

    OBJECTIVE:\\ud To examine associations between maternal height and child growth during 4 developmental periods: intrauterine, birth to age 2 years, age 2 years to mid-childhood (MC), and MC to adulthood.\\ud \\ud STUDY DESIGN:\\ud Pooled analysis of maternal height and offspring growth using 7630 mother-child pairs from 5 birth cohorts (Brazil, Guatemala, India, the Philippines, and South Africa). We used conditional height measures that control for collinearity in height across periods. We estim...

  15. The taking of Lucas Heights

    International Nuclear Information System (INIS)

    Sandilands, B.

    1993-01-01

    Plans for a new research reactor at Lucas Heights have sparked a 'civil war' in New South Wales. The author considers the arguments. The leading antagonists are the local government body - The Sutherland Shire Council, Greenpeace, and the Sutherland Shire Environment Centre. Many of the economic benefits claimed for the existing and proposed replacement reactor have been tagged with question marks. However, ANSTO is confident of refuting claims that the money could be better spent on alternative methods of producing medical isotopes and neutron streams for industry or research, such as particle accelerators. If ANSTO's critics have their way, non-reactor-dependent work like the laser enrichment project could continue without the alleged hazards of sustained nuclear fission. If ANSTO wins the day, a far more efficient reactor will be built which is capable of keeping pace with the emerging nuclear industries of Asia. ills

  16. Monitoring small pioneer trees in the forest-tundra ecotone: using multi-temporal airborne laser scanning data to model height growth.

    Science.gov (United States)

    Hauglin, Marius; Bollandsås, Ole Martin; Gobakken, Terje; Næsset, Erik

    2017-12-08

    Monitoring of forest resources through national forest inventory programmes is carried out in many countries. The expected climate changes will affect trees and forests and might cause an expansion of trees into presently treeless areas, such as above the current alpine tree line. It is therefore a need to develop methods that enable the inclusion of also these areas into monitoring programmes. Airborne laser scanning (ALS) is an established tool in operational forest inventories, and could be a viable option for monitoring tasks. In the present study, we used multi-temporal ALS data with point density of 8-15 points per m 2 , together with field measurements from single trees in the forest-tundra ecotone along a 1500-km-long transect in Norway. The material comprised 262 small trees with an average height of 1.78 m. The field-measured height growth was derived from height measurements at two points in time. The elapsed time between the two measurements was 4 years. Regression models were then used to model the relationship between ALS-derived variables and tree heights as well as the height growth. Strong relationships between ALS-derived variables and tree heights were found, with R 2 values of 0.93 and 0.97 for the two points in time. The relationship between the ALS data and the field-derived height growth was weaker, with R 2 values of 0.36-0.42. A cross-validation gave corresponding results, with root mean square errors of 19 and 11% for the ALS height models and 60% for the model relating ALS data to single-tree height growth.

  17. Boundary layer heights derived from velocity spectra

    Energy Technology Data Exchange (ETDEWEB)

    Hoejstrup, J.; Barthelmie, R.J. [Risoe National Lab., Roskilde (Denmark); Kaellstrand, B. [Univ. of Uppsala, Uppsala (Sweden)

    1997-10-01

    It is a well-known fact that the height of the mixed layer determines the size of the largest and most energetic eddies that can be observed in the unstable boundary layer, and consequently a peak can be observed in the power spectra of the along-wind velocity component at scales comparable to the mixed layer depth. We will now show how the mixed layer depth can be derived from the u-specta and the results will be compared with direct measurements using pibal and tethersonde measurements. (au)

  18. Genetically Determined Height and Coronary Artery Disease

    NARCIS (Netherlands)

    Nelson, Christopher P.; Hamby, Stephen E.; Saleheen, Danish; Hopewell, Jenna C.; Zeng, Lingyao; Assimes, Themistocles L.; Kanoni, Stavroula; Willenborg, Christina; Burgess, Stephen; Amouyel, Phillipe; Anand, Sonia; Blankenberg, Stefan; Boehm, Bernhard O.; Clarke, Robert J.; Collins, Rory; Dedoussis, George; Farrall, Martin; Franks, Paul W.; Groop, Leif; Hall, Alistair S.; Hamsten, Anders; Hengstenberg, Christian; Hovingh, G. Kees; Ingelsson, Erik; Kathiresan, Sekar; Kee, Frank; König, Inke R.; Kooner, Jaspal; Lehtimäki, Terho; März, Winifred; McPherson, Ruth; Metspalu, Andres; Nieminen, Markku S.; O'Donnell, Christopher J.; Palmer, Colin N. A.; Peters, Annette; Perola, Markus; Reilly, Muredach P.; Ripatti, Samuli; Roberts, Robert; Salomaa, Veikko; Shah, Svati H.; Schreiber, Stefan; Siegbahn, Agneta; Thorsteinsdottir, Unnur; Veronesi, Giovani; Wareham, Nicholas; Willer, Cristen J.; Zalloua, Pierre A.; Erdmann, Jeanette

    2015-01-01

    BACKGROUND The nature and underlying mechanisms of an inverse association between adult height and the risk of coronary artery disease (CAD) are unclear. METHODS We used a genetic approach to investigate the association between height and CAD, using 180 height-associated genetic variants. We tested

  19. Diagnostic test of predicted height model in Indonesian elderly: a study in an urban area

    Directory of Open Access Journals (Sweden)

    Fatmah Fatmah

    2010-08-01

    Full Text Available Aim In an anthropometric assessment, elderly are frequently unable to measure their height due to mobility and skeletal deformities. An alternative is to use a surrogate value of stature from arm span, knee height, and sitting height. The equations developed for predicting height in Indonesian elderly using these three predictors. The equations put in the nutritional assessment card (NSA of older people. Before the card which is the first new technology in Indonesia will be applied in the community, it should be tested. The study aimed was to conduct diagnostic test of predicted height model in the card compared to actual height.Methods Model validation towards 400 healthy elderly conducted in Jakarta City with cross-sectional design. The study was the second validation test of the model besides Depok City representing semi urban area which was undertaken as the first study.Result Male elderly had higher mean age, height, weight, arm span, knee height, and sitting height as compared to female elderly. The highest correlation between knee height and standing height was similar in women (r = 0.80; P < 0.001 and men (r = 0.78; P < 0.001, and followed by arm span and sitting height. Knee height had the lowest difference with standing height in men (3.13 cm and women (2.79 cm. Knee height had the biggest sensitivity (92.2%, and the highest specificity on sitting height (91.2%.Conclusion Stature prediction equation based on knee-height, arm span, and sitting height are applicable for nutritional status assessment in Indonesian elderly. (Med J Indones 2010;19:199-204Key words: diagnostic test, elderly, predicted height model

  20. HEIGHT GROWTH OF Araucaria angustifolia (Bert. O. Ktze. ON THREE NATURAL SITES, AT REGION OF CANELA - RS

    Directory of Open Access Journals (Sweden)

    Luciano Weber Scheeren

    2009-09-01

    Full Text Available This work has had as its principal objectives the study of dominant height growth considering its age in three natural sites, and the determination of natural sites classification efficacy for the Araucaria angustifolia (Bert. O. Ktze. in a planting stand in Canela, RS. For height and age data adjustment, determined through stem analysis, it was used the RICHARDS (1959 non-linear mathematics model, with two and three coefficients, resulting the three coefficient model as the most efficient to data adjustment of twelve dominant tree sampled on three natural sites in study. Seven groups of dominant trees with different trends growth were obtained, indicating that the natural sites classification did not detect with accuracy the effects of environmental  variables on height growth of Araucaria angustifolia.

  1. results

    Directory of Open Access Journals (Sweden)

    Salabura Piotr

    2017-01-01

    Full Text Available HADES experiment at GSI is the only high precision experiment probing nuclear matter in the beam energy range of a few AGeV. Pion, proton and ion beams are used to study rare dielectron and strangeness probes to diagnose properties of strongly interacting matter in this energy regime. Selected results from p + A and A + A collisions are presented and discussed.

  2. Variability Bugs:

    DEFF Research Database (Denmark)

    Melo, Jean

    . Although many researchers suggest that preprocessor-based variability amplifies maintenance problems, there is little to no hard evidence on how actually variability affects programs and programmers. Specifically, how does variability affect programmers during maintenance tasks (bug finding in particular......)? How much harder is it to debug a program as variability increases? How do developers debug programs with variability? In what ways does variability affect bugs? In this Ph.D. thesis, I set off to address such issues through different perspectives using empirical research (based on controlled...... experiments) in order to understand quantitatively and qualitatively the impact of variability on programmers at bug finding and on buggy programs. From the program (and bug) perspective, the results show that variability is ubiquitous. There appears to be no specific nature of variability bugs that could...

  3. Patella height changes post high tibial osteotomy

    Directory of Open Access Journals (Sweden)

    Siew Ghim Gooi

    2017-01-01

    Full Text Available Background: Medial opening wedge high tibial osteotomy (HTO is a well-described treatment in early medial compartmental osteoarthritis of the knee. However, two undesirable sequelae may follow –patella baja and changes in the posterior tibial slope (TS. Materials and Methods: We conducted a retrospective study in patients who underwent HTO in our center between September 2009 and February 2017. Preoperative and 6-week postoperative long-leg weight bearing films and lateral knee radiographs were assessed. Pre- and postoperative radiological measurements include the Caton-Deschamps Index (CDI, the mechanical axis deviation (MAD, and the posterior TS. Independant t-test and Pearson correlation test were performed. Results: A total of 106 knees were recruited. The mean age was 48.8 ± 10.8 years. 66 (62.3% and 40 (37.7% knees were from males and females, respectively. The mean pre- and postoperative measurements was (−9.70° ± 3.67° to 0.08° ± 2.80° (−varus; +valgus for the MAD, (7.14° ± 1.78° to 8.72° ± 3.11° for posterior TS, and (0.93° ± 0.084° to 0.82° ± 0.13° for CDI (P ≤ 0.001 for all. The association between patella height change and the level of osteotomy (supra-tubercle vs. infra-tubercle was statistically significant (P < 0.001. A supra-tubercle osteotomy cut significantly lowering patella height (P = 0.011. There was otherwise no statistically significant correlations between patella height changes and the correction angle (P = 0.187 or posterior TS change (P = 0.744. Conclusions: A medial opening wedge HTO above the tibial tubercle was significantly associated with lowering patella height or reducing CDI postoperatively. Based on our results, we would recommend the use of an infra-tubercle osteotomy during the corrective surgery to prevent the complication of patella baja.

  4. Clustering of France Monthly Precipitation, Temperature and Discharge Based on their Multiresolution Links with 500mb Geopotential Height from 1968 to 2008

    Science.gov (United States)

    Massei, N.; Fossa, M.; Dieppois, B.; Vidal, J. P.; Fournier, M.; Laignel, B.

    2017-12-01

    In the context of climate change and ever growing use of water resources, identifying how the climate and watershed signature in discharge variability changes with the geographic location is of prime importance. This study aims at establishing how 1968-2008 multiresolution links between 3 local hydrometerological variables (precipitation, temperature and discharge) and 500 mb geopotential height are structured over France. First, a methodology that allows to encode the 3D geopotential height data into its 1D conformal modulus time series is introduced. Then, for each local variable, their covariations with the geopotential height are computed with cross wavelet analysis. Finally, a clustering analysis of each variable cross spectra is done using bootstrap clustering.We compare the clustering results for each local variable in order to untangle the watershed from the climate drivers in France's rivers discharge. Additionally, we identify the areas in the geopotential height field that are responsible for the spatial structure of each local variable.Main results from this study show that for precipitation and discharge, clear spatial zones emerge. Each cluster is characterized either by different different amplitudes and/or time scales of covariations with geopotential height. Precipitation and discharge clustering differ with the later being simpler which indicates a strong low frequency modulation by the watersheds all over France. Temperature on the other hand shows less clearer spatial zones. For precipitation and discharge, we show that the main action path starts at the northern tropical zone then moves up the to central North Atlantic zone which seems to indicates an interaction between the convective cells variability and the reinforcement of the westerlies jets as one of the main control of the precipitation and discharge over France. Temperature shows a main zone of action directly over France hinting at local temperature/pressure interactions.

  5. Global Distribution of Planetary Boundary Layer Height Derived from CALIPSO

    Science.gov (United States)

    Huang, J.

    2015-12-01

    The global distribution of planetary boundary layer (PBL) height, which was estimated from the attenuated back-scatter observations of Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO), is presented. In general, the PBL is capped by a temperature inversion that tends to trap moisture and aerosols. The gradient of back-scatter observed by lidar is almost always associated with this temperature inversion and the simultaneous decrease of moisture content. Thus, the PBL top is defined as the location of the maximum aerosol scattering gradient, which is analogous to the more conventional thermodynamic definition. The maximum standard deviation method, developed by Jordan et al. (2010), is modified and used to derive the global PBL heights. The derived PBL heights are not only consistent with the results of McGrath-Spangler and Denning (2012) but also agree well with the ground-based lidar measurements. It is found that the correlation between CALIPSO and the ground-based lidar was 0.73. The seasonal mean patterns from 4-year mid-day PBL heights over global are demonstrated. Also it is found that the largest PBL heights occur over the Tibetan Plateau and the coastal areas. The smallest PBL heights appear in the Tarim Basin and the northeast of China during the local winter. The comparison of PBL heights from CALIPSO and ECMWF under different land-cover conditions showed that, over ocean and forest surface, the PBL height estimated from the CALIPSO back-scatter climatology is larger than the ones estimated from ECMWF data. However, the PBL heights from ECMWF, over grass land and bare land surface in spring and summer are larger than the ones from CALIPSO.

  6. Wood Specific Gravity Variation with Height and Its Implications for Biomass Estimation

    Science.gov (United States)

    Michael C. Wiemann; G. Bruce Williamson

    2014-01-01

    Wood specific gravity (SG) is widely employed by ecologists as a key variable in estimates of biomass. When it is important to have nondestructive methods for sampling wood for SG measurements, cores are extracted with an increment borer. While boring is a relatively difficult task even at breast height sampling, it is impossible at ground level and arduous at heights...

  7. A rigorous assessment of tree height measurements obtained using airborne LIDAR and conventional field methods.

    Science.gov (United States)

    Hans-Erik Andersen; Stephen E. Reutebuch; Robert J. McGaughey

    2006-01-01

    Tree height is an important variable in forest inventory programs but is typically time-consuming and costly to measure in the field using conventional techniques. Airborne light detection and ranging (LIDAR) provides individual tree height measurements that are highly correlated with field-derived measurements, but the imprecision of conventional field techniques does...

  8. South America, Shaded Relief and Colored Height

    Science.gov (United States)

    2003-01-01

    This image of South America was generated with data from the Shuttle Radar Topography Mission (SRTM). For this broad view the resolution of the data was first reduced to 30 arcseconds (about 928 meters north-south but variable east-west), matching the best previously existing global digital topographic data set called GTOPO30. The data were then resampled to a Mercator projection with approximately square pixels (about one kilometer, or 0.6 miles, on each side). Even at this decreased resolution the variety of landforms comprising the South American continent is readily apparent.Topographic relief in South America is dominated by the Andes Mountains, which extend all along the Pacific Coast. These mountains are created primarily by the convergence of the Nazca and South American tectonic plates. The Nazca Plate, which underlies the eastern Pacific Ocean, slides under western South America resulting in crustal thickening, uplift, and volcanism. Another zone of plate convergence occurs along the northwestern coast of South America where the Caribbean Plate also slides under the South American Plate and forms the northeastern extension of the Andes Mountains.East of the Andes, much of northern South America drains into the Amazon River, the world's largest river in terms of both watershed area and flow volume. Topographic relief is very low in much of the Amazon Basin but SRTM data provide an excellent detailed look at the basin's three-dimensional drainage pattern, including the geologic structural trough (syncline) that hosts the eastern river channel.North of the Amazon, the Guiana Highlands commonly stand in sharp contrast to the surrounding lowlands, indeed hosting the world's tallest waterfall, Angel Falls (979 meters or 3212 feet). Folded and fractured bedrock structures are distinctive in the topographic pattern.South of the Amazon, the Brazilian Highlands show a mix of landforms, including some broad areas of consistent topographic patterns that indicate the

  9. Modelling foot height and foot shape-related dimensions.

    Science.gov (United States)

    Xiong, Shuping; Goonetilleke, Ravindra S; Witana, Channa P; Lee Au, Emily Yim

    2008-08-01

    The application of foot anthropometry to design good-fitting footwear has been difficult due to the lack of generalised models. This study seeks to model foot dimensions so that the characteristic shapes of feet, especially in the midfoot region, can be understood. Fifty Hong Kong Chinese adults (26 males and 24 females) participated in this study. Their foot lengths, foot widths, ball girths and foot heights were measured and then evaluated using mathematical models. The results showed that there were no significant allometry (p > 0.05) effects of foot length on ball girth and foot width. Foot height showed no direct relationship with foot length. However, a normalisation with respect to foot length and foot height resulted in a significant relationship for both males and females with R(2) greater than 0.97. Due to the lack of a direct relationship between foot height and foot length, the current practice of grading shoes with a constant increase in height or proportionate scaling in response to foot length is less than ideal. The results when validated with other populations can be a significant way forward in the design of footwear that has an improved fit in the height dimension.

  10. A macroecological analysis of SERA derived forest heights and implications for forest volume remote sensing.

    Science.gov (United States)

    Brolly, Matthew; Woodhouse, Iain H; Niklas, Karl J; Hammond, Sean T

    2012-01-01

    Individual trees have been shown to exhibit strong relationships between DBH, height and volume. Often such studies are cited as justification for forest volume or standing biomass estimation through remote sensing. With resolution of common satellite remote sensing systems generally too low to resolve individuals, and a need for larger coverage, these systems rely on descriptive heights, which account for tree collections in forests. For remote sensing and allometric applications, this height is not entirely understood in terms of its location. Here, a forest growth model (SERA) analyzes forest canopy height relationships with forest wood volume. Maximum height, mean, H₁₀₀, and Lorey's height are examined for variability under plant number density, resource and species. Our findings, shown to be allometrically consistent with empirical measurements for forested communities world-wide, are analyzed for implications to forest remote sensing techniques such as LiDAR and RADAR. Traditional forestry measures of maximum height, and to a lesser extent H₁₀₀ and Lorey's, exhibit little consistent correlation with forest volume across modeled conditions. The implication is that using forest height to infer volume or biomass from remote sensing requires species and community behavioral information to infer accurate estimates using height alone. SERA predicts mean height to provide the most consistent relationship with volume of the height classifications studied and overall across forest variations. This prediction agrees with empirical data collected from conifer and angiosperm forests with plant densities ranging between 10²-10⁶ plants/hectare and heights 6-49 m. Height classifications investigated are potentially linked to radar scattering centers with implications for allometry. These findings may be used to advance forest biomass estimation accuracy through remote sensing. Furthermore, Lorey's height with its specific relationship to remote sensing

  11. Childhood height increases the risk of prostate cancer mortality

    DEFF Research Database (Denmark)

    Aarestrup, J; Gamborg, M; Cook, M B

    2015-01-01

    cancers. Cox proportional hazards regressions were performed. RESULTS: 630 men had prostate cancer recorded as the underlying cause of death. Childhood height at age 13years was positively associated with prostate cancer-specific mortality (hazard ratio [HR]per z-score=1.2, 95% confidence interval [CI]: 1.1-1.3......). Associations were significant at all other childhood ages. Growth analyses showed that height at age 13years had a stronger association with prostate cancer-specific mortality than height at age 7, suggesting the association at age 7 is largely mediated through later childhood height. The tallest boys at age...... 13years had a significantly worse survival, but only when restricted to a diagnosis at years of age (HRz-score of 1=1.7, 95% CI: 1.3-2.4). These associations were significant at all other childhood ages. Childhood BMI was not associated with prostate cancer mortality or survival. CONCLUSION...

  12. Interobserver variability in gross tumor volume delineation for hepatocellular carcinoma. Results of Korean Radiation Oncology Group 1207 study

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Suk [Jeju National University School of Medicine, Department of Radiation Oncology, Jeju National University Hospital, Jeju (Korea, Republic of); Kim, Jun Won; Lee, Ik Jae [Yonsei University College of Medicine, Department of Radiation Oncology, Gangnam Severance Hospital, Seoul (Korea, Republic of); Yoon, Won Sup [Korea University Medical Center, Department of Radiation Oncology, Ansan Hospital, Ansan (Korea, Republic of); Kang, Min Kyu [Kyungpook National University School of Medicine, Department of Radiation Oncology, Daegu (Korea, Republic of); Kim, Tae Hyun [National Cancer Center, Center for Liver Cancer, Goyang (Korea, Republic of); Kim, Jin Hee [Keimyung University School of Medicine, Department of Radiation Oncology, Dongsan Medical Center, Daegu (Korea, Republic of); Lee, Hyung-Sik [Dong-A University College of Medicine, Department of Radiation Oncology, Busan (Korea, Republic of); Park, Hee Chul [Sungkyunkwan University School of Medicine, Department of Radiation Oncology, Samsung Medical Center, Seoul (Korea, Republic of); Jang, Hong Seok; Kay, Chul Seung [The Catholic University of Korea College of Medicine, Department of Radiation Oncology, Seoul (Korea, Republic of); Yoon, Sang Min [University of Ulsan College of Medicine, Department of Radiation Oncology, Asan Medical Center, Seoul (Korea, Republic of); Kim, Mi-Sook [Korea Institute of Radiological and Medical Sciences, Department of Radiation Oncology, Seoul (Korea, Republic of); Seong, Jinsil [Yonsei University College of Medicine, Department of Radiation Oncology, Severance Hospital, Seodaemun-gu, Seoul (Korea, Republic of)

    2016-10-15

    There has been increasing use of external beam radiotherapy for localized treatment of hepatocellular carcinoma (HCC) with both palliative and curative intent. Quality control of target delineation in primary HCC is essential to deliver adequate doses of radiation to the primary tumor while preserving adjacent healthy organs. We analyzed interobserver variability in gross tumor volume (GTV) delineation for HCC. Twelve radiation oncologists specializing in liver malignancy participated in a multi-institutional contouring dummy-run study of nine HCC cases and independently delineated GTV on the same set of provided computed tomography images. Quantitative analysis was performed using an expectation maximization algorithm for simultaneous truth and performance level estimation (STAPLE) with kappa statistics calculating agreement between physicians. To quantify the interobserver variability of GTV delineations, the ratio of the actual delineated volume to the estimated consensus volume (STAPLE), the ratio of the common and encompassing volumes, and the coefficient of variation were calculated. The median kappa agreement level was 0.71 (range 0.28-0.86). The ratio of the actual delineated volume to the estimated consensus volume ranged from 0.19 to 1.93 (median 0.94) for all cases. The ratio of the common and encompassing volumes ranged from 0.001 to 0.56 (median 0.25). The coefficient of variation for GTV delineation ranged from 8 to 57 % (median 26 %). The interobserver variability in target delineation of HCC GTV in this study is noteworthy. Multi-institution studies involving radiotherapy for HCC require appropriate quality assurance programs for target delineation. (orig.) [German] Die externe kurative Strahlentherapie ist zunehmend bei der lokalisierten Behandlung hepatozellulaerer Karzinome (HCC) in palliativer und kurativer Absicht in Gebrauch. Eine Qualitaetskontrolle der Zielabgrenzung beim primaeren HCC ist entscheidend, um die passende Dosis fuer die

  13. Development of a pulse height analizer

    International Nuclear Information System (INIS)

    Moreira, E.S.

    1984-01-01

    The development of a Pulse Height Analizer is described. This equipment is essential to analize data coming from detectors producing information codified in pulse amplitudes. The system developed consist of a Signal Input Module connected to a Controller Module based on a 8085A microprocessor capable to memorize pulses up to 1 uS in 256 channels with a resolution better than 20 mV. A Communication Module with a serial interface is used for data transfer to a host computer using RS232c protocol. The Monitoring and Operation Module consist of a hexadecimal Keybord, a 6 digit 7-segment display and a XY analog output enabling real time visualization of data on a XY monitor. The hardware and the software designed for this low cost system were optimized to obtain a typical dead time of approximately 100 uS. As application, this device was used to adquire curves at the Small Angle X-ray Scattering Laboratory in this Department. The apparatus performance was tested by comparing its data with a Northern Pulse Height Analizer model NS633 output, with favorable results. (Author) [pt

  14. Development of VariLeg, an exoskeleton with variable stiffness actuation: first results and user evaluation from the CYBATHLON 2016.

    Science.gov (United States)

    Schrade, Stefan O; Dätwyler, Katrin; Stücheli, Marius; Studer, Kathrin; Türk, Daniel-Alexander; Meboldt, Mirko; Gassert, Roger; Lambercy, Olivier

    2018-03-13

    Powered exoskeletons are a promising approach to restore the ability to walk after spinal cord injury (SCI). However, current exoskeletons remain limited in their walking speed and ability to support tasks of daily living, such as stair climbing or overcoming ramps. Moreover, training progress for such advanced mobility tasks is rarely reported in literature. The work presented here aims to demonstrate the basic functionality of the VariLeg exoskeleton and its ability to enable people with motor complete SCI to perform mobility tasks of daily life. VariLeg is a novel powered lower limb exoskeleton that enables adjustments to the compliance in the leg, with the objective of improving the robustness of walking on uneven terrain. This is achieved by an actuation system with variable mechanical stiffness in the knee joint, which was validated through test bench experiments. The feasibility and usability of the exoskeleton was tested with two paraplegic users with motor complete thoracic lesions at Th4 and Th12. The users trained three times a week, in 60 min sessions over four months with the aim of participating in the CYBATHLON 2016 competition, which served as a field test for the usability of the exoskeleton. The progress on basic walking skills and on advanced mobility tasks such as incline walking and stair climbing is reported. Within this first study, the exoskeleton was used with a constant knee stiffness. Test bench evaluation of the variable stiffness actuation system demonstrate that the stiffness could be rendered with an error lower than 30 Nm/rad. During training with the exoskeleton, both users acquired proficient skills in basic balancing, walking and slalom walking. In advanced mobility tasks, such as climbing ramps and stairs, only basic (needing support) to intermediate (able to perform task independently in 25% of the attempts) skill levels were achieved. After 4 months of training, one user competed at the CYBATHLON 2016 and was able to perform 3

  15. Final height in survivors of childhood cancer compared with Height Standard Deviation Scores at diagnosis.

    Science.gov (United States)

    Knijnenburg, S L; Raemaekers, S; van den Berg, H; van Dijk, I W E M; Lieverst, J A; van der Pal, H J; Jaspers, M W M; Caron, H N; Kremer, L C; van Santen, H M

    2013-04-01

    Our study aimed to evaluate final height in a cohort of Dutch childhood cancer survivors (CCS) and assess possible determinants of final height, including height at diagnosis. We calculated standard deviation scores (SDS) for height at initial cancer diagnosis and height in adulthood in a cohort of 573 CCS. Multivariable regression analyses were carried out to estimate the influence of different determinants on height SDS at follow-up. Overall, survivors had a normal height SDS at cancer diagnosis. However, at follow-up in adulthood, 8.9% had a height ≤-2 SDS. Height SDS at diagnosis was an important determinant for adult height SDS. Children treated with (higher doses of) radiotherapy showed significantly reduced final height SDS. Survivors treated with total body irradiation (TBI) and craniospinal radiation had the greatest loss in height (-1.56 and -1.37 SDS, respectively). Younger age at diagnosis contributed negatively to final height. Height at diagnosis was an important determinant for height SDS at follow-up. Survivors treated with TBI, cranial and craniospinal irradiation should be monitored periodically for adequate linear growth, to enable treatment on time if necessary. For correct interpretation of treatment-related late effects studies in CCS, pre-treatment data should always be included.

  16. Vagally-mediated heart rate variability and indices of well-being: Results of a nationally representative study.

    Science.gov (United States)

    Sloan, Richard P; Schwarz, Emilie; McKinley, Paula S; Weinstein, Maxine; Love, Gayle; Ryff, Carol; Mroczek, Daniel; Choo, Tse-Hwei; Lee, Seonjoo; Seeman, Teresa

    2017-01-01

    High frequency (HF) heart rate variability (HRV) has long been accepted as an index of cardiac vagal control. Recent studies report relationships between HF-HRV and indices of positive and negative affect, personality traits and well-being but these studies generally are based on small and selective samples. These relationships were examined using data from 967 participants in the second Midlife in the U.S. (MIDUS II) study. Participants completed survey questionnaires on well-being and affect. HF-HRV was measured at rest. A hierarchical series of regression analyses examined relationships between these various indices and HF-HRV before and after adjustment for relevant demographic and biomedical factors. Significant inverse relationships were found only between indices of negative affect and HF-HRV. Relationships between indices of psychological and hedonic well-being and positive affect failed to reach significance. These findings raise questions about relationships between cardiac parasympathetic modulation, emotion regulation, and indices of well-being. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  17. Imagery and fear influence height perception.

    Science.gov (United States)

    Clerkin, Elise M; Cody, Meghan W; Stefanucci, Jeanine K; Proffitt, Dennis R; Teachman, Bethany A

    2009-04-01

    The current study tested whether height overestimation is related to height fear and influenced by images of falling. To assess perceptual biases, participants high (n=65) versus low (n=64) in height fear estimated the vertical extents of two balconies using a visual matching task. On one of the balconies, participants engaged in an imagery exercise designed to enhance the subjective sense that they were acting in a dangerous environment by picturing themselves falling. As expected, we found that individuals overestimated the balcony's height more after they imagined themselves falling, particularly if they were already afraid of heights. These findings suggest that height fear may serve as a vulnerability factor that leads to perceptual biases when triggered by a stressor (in this case, images of falling).

  18. Tracing the accretion history of supermassive black holes through X-ray variability: results from the ChandraDeep Field-South

    Science.gov (United States)

    Paolillo, M.; Papadakis, I.; Brandt, W. N.; Luo, B.; Xue, Y. Q.; Tozzi, P.; Shemmer, O.; Allevato, V.; Bauer, F. E.; Comastri, A.; Gilli, R.; Koekemoer, A. M.; Liu, T.; Vignali, C.; Vito, F.; Yang, G.; Wang, J. X.; Zheng, X. C.

    2017-11-01

    We study the X-ray variability properties of distant active galactic nuclei (AGNs) in the ChandraDeep Field-South region over 17 yr, up to z ˜ 4, and compare them with those predicted by models based on local samples. We use the results of Monte Carlo simulations to account for the biases introduced by the discontinuous sampling and the low-count regime. We confirm that variability is a ubiquitous property of AGNs, with no clear dependence on the density of the environment. The variability properties of high-z AGNs, over different temporal time-scales, are most consistent with a power spectral density (PSD) described by a broken (or bending) power law, similar to nearby AGNs. We confirm the presence of an anticorrelation between luminosity and variability, resulting from the dependence of variability on black hole (BH) mass and accretion rate. We explore different models, finding that our acceptable solutions predict that BH mass influences the value of the PSD break frequency, while the Eddington ratio λEdd affects the PSD break frequency and, possibly, the PSD amplitude as well. We derive the evolution of the average λEdd as a function of redshift, finding results in agreement with measurements based on different estimators. The large statistical uncertainties make our results consistent with a constant Eddington ratio, although one of our models suggest a possible increase of λEdd with lookback time up to z ˜ 2-3. We conclude that variability is a viable mean to trace the accretion history of supermassive BHs, whose usefulness will increase with future, wide-field/large effective area X-ray missions.

  19. On the Predictability of Hub Height Winds

    DEFF Research Database (Denmark)

    Draxl, Caroline

    Wind energy is a major source of power in over 70 countries across the world, and the worldwide share of wind energy in electricity consumption is growing. The introduction of signicant amounts of wind energy into power systems makes accurate wind forecasting a crucial element of modern electrical...... grids. These systems require forecasts with temporal scales of tens of minutes to a few days in advance at wind farm locations. Traditionally these forecasts predict the wind at turbine hub heights; this information is then converted by transmission system operators and energy companies into predictions...... of power output at wind farms. Since the power available in the wind is proportional to the wind speed cubed, even small wind forecast errors result in large power prediction errors. Accurate wind forecasts are worth billions of dollars annually; forecast improvements will result in reduced costs...

  20. The Analysis of Height System Definition and the High Precision GNSS Replacing Leveling Method

    Directory of Open Access Journals (Sweden)

    ZHANG Chuanyin

    2017-08-01

    Full Text Available Based on the definition of height system, the gravitational equipotential property of height datum surface is discussed in this paper, differences of the heights at ground points that defined in different height systems are tested and analyzed as well. A new method for replacing leveling using GNSS is proposed to ensure the consistency between GNSS replacing leveling and spirit leveling at mm accuracy level. The main conclusions include:①For determining normal height at centimeter accuracy level, the datum surface of normal height should be the geoid. The 1985 national height datum of China adopts normal height system, its datum surface is the geoid passing the Qingdao zero point.②The surface of equi-orthometric height in the near earth space is parallel to the geoid. The combination of GNSS precise positioning and geoid model can be directly used for orthometric height determination. However, the normal height system is more advantageous for describing the terrain and relief.③Based on the proposed method of GNSS replacing leveling, the errors in geodetic height affect more on normal height result than the errors of geoid model, the former is about 1.5 times of the latter.

  1. Adult height, nutrition, and population health

    Science.gov (United States)

    Perkins, Jessica M.; Subramanian, S.V.; Davey Smith, George

    2016-01-01

    In this review, the potential causes and consequences of adult height, a measure of cumulative net nutrition, in modern populations are summarized. The mechanisms linking adult height and health are examined, with a focus on the role of potential confounders. Evidence across studies indicates that short adult height (reflecting growth retardation) in low- and middle-income countries is driven by environmental conditions, especially net nutrition during early years. Some of the associations of height with health and social outcomes potentially reflect the association between these environmental factors and such outcomes. These conditions are manifested in the substantial differences in adult height that exist between and within countries and over time. This review suggests that adult height is a useful marker of variation in cumulative net nutrition, biological deprivation, and standard of living between and within populations and should be routinely measured. Linkages between adult height and health, within and across generations, suggest that adult height may be a potential tool for monitoring health conditions and that programs focused on offspring outcomes may consider maternal height as a potentially important influence. PMID:26928678

  2. Influence of clinical and laboratory variables on faecal antigen ELISA results in dogs with canine parvovirus infection.

    Science.gov (United States)

    Proksch, A L; Unterer, S; Speck, S; Truyen, U; Hartmann, K

    2015-06-01

    False negative faecal canine parvovirus (CPV) antigen ELISA results in dogs with CPV infection are common, but the factors that lead to these false negative results are still unknown. The aim of this study was to investigate whether dogs with a false negative faecal CPV antigen ELISA result have milder clinical signs and laboratory changes, a lower faecal virus load, higher faecal and serum CPV antibody titres and a faster recovery than dogs with a positive result. Eighty dogs with CPV infection, confirmed by the presence of clinical signs and a positive faecal CPV polymerase chain reaction (PCR), were assigned to two groups according to their faecal antigen ELISA result. Time until presentation, severity of symptoms, laboratory parameters, faecal virus load, faecal and serum antibody titres, and CPV sequencing data were compared between both groups. In 38/80 dogs that were hospitalised until recovery, the time to recovery, mortality, and the course of the disease were compared between dogs with positive and negative faecal antigen ELISA results. Of the 80 dogs included, 41 (51.3%) had a false negative faecal antigen ELISA result. ELISA-negative dogs had a significantly shorter time until presentation, lower frequency of defaecation, lower faecal virus load, and higher serum antibody concentrations than ELISA-positive dogs. Laboratory changes, CPV shedding, and outcomes were not associated with faecal antigen ELISA results. In conclusion, low faecal CPV load and antibodies binding to CPV antigen in faeces are likely to be important reasons for false negative faecal antigen ELISA results. Dogs with clinical signs of CPV infection should be retested by faecal PCR. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Preliminary results from the ESA STSE project on SST diurnal variability, its regional extent and implications in atmospheric modelling (SSTDV:R.EX.–IM.A.M.)

    DEFF Research Database (Denmark)

    Karagali, Ioanna; Hasager, Charlotte Bay; Høyer, Jacob L.

    2013-01-01

    This study presents some preliminary results of the ESA Support To Science Element (STSE) funded project on the Diurnal Variability of the Sea Surface Temperature, regarding its Regional Extend and Implications in Atmospheric Modelling (SSTDV:R.EX.–IM.A.M.). Comparisons of SEVIRI SST with AATSR...

  4. Plume Dispersion over Idealized Urban-liked Roughness with Height Variation: an LES Approach

    Science.gov (United States)

    Wong, Colman Ching Chi; Liu, Chun-Ho

    2013-04-01

    Human activities (e.g. vehicular emission) are the primary pollutant sources affecting the health and living quality of stakeholders in modern compact cities. Gaussian plume dispersion model is commonly used for pollutant distribution estimate that works well over rural areas with flat terrain. However, its major parameters, dispersion coefficients, exclude the effect of surface roughness that unavoidably prone to error handling the pollutant transport in the urban boundary layer (UBL) over building roughness. Our recent large-eddy simulation (LES) has shown that urban surfaces affect significantly the pollutant dispersion over idealized, identical two-dimensional (2D) street canyons of uniform height. As an extension to our on-going effort, this study is conceived to investigate how rough urban surfaces, which are constructed by 2D street canyons of non-uniform height, modify the UBL pollutant dispersion . A series of LESs with idealized roughness elements of non-uniform heights were performed in neutral stratification. Building models with two different heights were placed alternatively in the computational domain to construct 2D street canyons in cross flows. The plume dispersion from a ground-level passive pollutant source over more realistic urban areas was then examined. Along with the existing building-height-to-street-width (aspect) ratio (AR), a new parameter, building-height variability (BHV), is used to measure the building height unevenness. Four ARs (1, 0.5, 0.25 and 0.125) and three BHVs (20%, 40% and 60%) were considered in this study. Preliminary results show that BHV greatly increases the aerodynamic roughness of the hypothetical urban surfaces for narrow street canyons. Analogous to our previous findings, the air exchange rate (ACH) of street canyons increases with increasing friction factor, implying that street-level ventilation could be improved by increasing building roughness via BHV. In addition, the parameters used in dispersion coefficient

  5. Weighting of field heights for sharpness and noisiness

    Science.gov (United States)

    Keelan, Brian W.; Jin, Elaine W.

    2009-01-01

    Weighting of field heights is important in cases when a single numerical value needs to be calculated that characterizes an attribute's overall impact on perceived image quality. In this paper we report an observer study to derive the weighting of field heights for sharpness and noisiness. One-hundred-forty images were selected to represent a typical consumer photo space distribution. Fifty-three sample points were sampled per image, representing field heights of 0, 14, 32, 42, 51, 58, 71, 76, 86% and 100%. Six observers participated in this study. The field weights derived in this report include both: the effect of area versus field height (which is a purely objective, geometric factor); and the effect of the spatial distribution of image content that draws attention to or masks each of these image structure attributes. The results show that relative to the geometrical area weights, sharpness weights were skewed to lower field heights, because sharpness-critical subject matter was often positioned relatively near the center of an image. Conversely, because noise can be masked by signal, noisiness-critical content (such as blue skies, skin tones, walls, etc.) tended to occur farther from the center of an image, causing the weights to be skewed to higher field heights.

  6. VARIABLE STARS IN THE LARGE MAGELLANIC CLOUD GLOBULAR CLUSTER NGC 2257. I. RESULTS BASED ON 2007-2008 B, V PHOTOMETRY

    International Nuclear Information System (INIS)

    Nemec, James M.; Walker, Alistair; Jeon, Young-Beom

    2009-01-01

    The variable stars in the Large Magellanic Cloud star cluster NGC 2257 are reinvestigated using photometry (to ∼20th mag) of over 400 new B, V CCD images taken with the CTIO 0.9 m telescope on 14 nights in 2007 December and 2008 January. New period searches have been made using two independent algorithms (CLEAN, Period04); the resultant periods of most of the stars are consistent with the pulsation periods derived previously, and where there are discrepancies these have been resolved. For the B and V light curves, accurate Fourier coefficients and parameters are given. Six new variable stars have been discovered (V45-50), including a bright candidate long-period variable star showing secondary oscillations (V45) and two anomalously bright RRc stars (V48 and V50), which are shown to be brightened and reddened by nearby red giant stars. Also discovered among the previously known variable stars are three double-mode RR Lyrae stars (V8, V16, and V34) and several Blazhko variables. Archival Hubble Space Telescope images and the photometry by Johnson et al. have been used to define better the properties of the most crowded variable stars. The total number of cluster variable stars now stands at forty-seven: 23 RRab stars, four of which show Blazhko amplitude variations; 20 RRc stars, one showing clear Blazhko variations and another showing possible Blazhko variations; the three RRd stars, all having the dominant period ∼0.36 day and period ratios P 1 /P 0 ∼0.7450; and an LPV star located near the tip of the red giant branch. A comparison of the RRd stars with those in other environments shows them to be most similar to those in IC4499.

  7. THE POLISH SEJM ELECTIONS OF 2015: SPACE VARIABILITY OF THE RESULTS BASED ON SINGLE-MEMBER CONSTITUENCIES SIMULATION

    Directory of Open Access Journals (Sweden)

    Oskar SKOMSKI

    2017-11-01

    Full Text Available The main assumption of this paper is to analyse the Sejm elections of 2015 results. The authors conducted a simulation study regarding the single-member constituencies in the election to the Polish Parliament, basing the research on the election results facilitated by National Electoral Commission as well as the specific data provided by Central Statistical Office. The division of Poland into 460 single-member constituencies was mapped by the authors (those maps do not include the district divisions in the cities, as the agglomerations’ division is problematic. Obtained results indicate to the marginalization of the Polish political scene – plural voting would preclude the election victories of the secondary political parties and civil rights movements.

  8. Validity of self-reported weight, height, and BMI in mothers of the research Birth in Brazil

    Directory of Open Access Journals (Sweden)

    Roberta Gabriela Pimenta da Silva Araújo

    2017-12-01

    Full Text Available ABSTRACT OBJECTIVE To evaluate the accuracy of information on pre-gestational weight, height, pre-gestational body mass index, and weight at the last prenatal appointment, according to maternal characteristics and sociodemographic and prenatal variables. METHODS The study was developed using data from the face-to-face questionnaire and prenatal card (gold standard of the study “Birth in Brazil, 2011–2012”. To evaluate the differences between the measured and self-reported anthropometric variables, we used the the Kruskal-Wallis test for the variables divided into quartiles. For the continuous variables, we used the Wilcoxon test, Bland-Altman plot, and average difference between the information measured and reported by the women. We estimated sensitivity and the intraclass correlation coefficient. RESULTS In the study, 17,093 women had the prenatal card. There was an underestimation of pre-gestational weight of 1.51 kg (SD = 3.44 and body mass index of 0.79 kg/m2 (SD = 1.72 and overestimation of height of 0.75 cm (SD = 3.03 and weight at the last appointment of 0.22 kg (SD = 2.09. The intraclass correlation coefficients (ICC obtained for the anthropometric variables were: height (ICC = 0.89, pre-gestational weight (ICC = 0.96, pre-gestational body mass index (ICC = 0.92, and weight at the last appointment (ICC = 0.98. CONCLUSIONS The results suggest that the mentioned anthropometric variables were valid for the study population, and they may be used in studies of populations with similar characteristics.

  9. Boundary layer height determination under summertime anticyclonic weather conditions over the coastal area of Rijeka, Croatia

    Energy Technology Data Exchange (ETDEWEB)

    Nitis, T.; Moussiopoulos, N. [Aristotle Univ. Thessaloniki (Greece). Lab. of Heat Transfer and Environmental Engineering; Klaic, Z.B. [Univ. of Zagreb (Croatia). Andrija Mohorovicic Geophysical Inst., Faculty of Science; Kitsiou, D. [Univ. of the Aegean, Mytilene (Greece). Dept. of Marine Sciences

    2004-07-01

    The atmospheric boundary layer height is a fundamental parameter characterising the structure of the lower troposphere. The determination of this parameter is important in applications that range from meteorological modelling and forecasting to dispersion problems of atmospheric pollutants. Since substances emitted into the atmospheric boundary layer are dispersed horizontally and vertically through the action of turbulence, they are well-mixed over this layer that is widely known as ''mixing layer''. There are two basic approaches for the practical estimation of this height; the first approach suggests profile measurements, either in-situ or by remote sounding (sodar, clear-air radar, lidar) and the second one, the use of models with only a few measured parameters as input. As far as the second approach is concerned, the majority of the models use relatively crude estimates of the roughness length that is often based on constant values for land cover. Consequently, the model results are not quite accurate. The present work aims firstly to evaluate the effect of alternative calculations of the roughness length on the non-hydrostatic mesoscale model (MEMO) performance, based on the use of satellite data, and secondly, to estimate the mixing layer height and analyze its variability in relation to underlying topography and land use. Rijeka, a region with complex topography and several islands in its surroundings, offers the opportunity to examine the above mentioned relationships. The non-hydrostatic mesoscale model MEMO was applied under summertime anticyclonic weather conditions during two multi-day periods characterised by stagnant meteorological conditions. The results proved MEMO capable of simulating mesoscale wind flow reasonably well, however, the use of AVHRR satellite data for calculating the roughness length based on the calculation of the NDVI parameter, optimised the model performance and resulted to a more accurate determination of

  10. Relations of diet and physical activity to bone mass and height in black and white adolescents

    Directory of Open Access Journals (Sweden)

    Yanbin Dong

    2011-06-01

    Full Text Available Because the development of healthy bodies during the years of growth has life-long health consequences, it is important to understand the early influences of diet and physical activity (PA. One way to generate hypotheses concerning such influences is to conduct cross-sectional studies of how diet and PA are related to different components of body composition. The subjects were 660 black and white adolescents. Total body bone mineral content (BMC was measured with dual-energy X-ray absorptiometry; free-living diet and PA were assessed with 4-7 separate 24-h recalls. The main dietary variables investigated were: total energy intake, macronutrient distribution (%, dairy servings, vitamin D, and calcium. The main PA variables were hours of moderate PA (3-6 METs and vigorous PA (>6 METs. BMC was higher in blacks than in whites (P<0.01 and it increased more in boys than in girls (age by sex interaction as age increased (P<0.01. After adjustment for age, race and sex, higher levels of BMC were associated with higher levels of energy intake, dairy servings, calcium, vitamin D, and vigorous PA (all P 's<0.05. In the multivariable model, significant and independent proportions of the variance in BMC were explained by race, the age by sex interaction, calcium, and vigorous PA (all P 's<0.01. When height was used as the outcome variable, similar diet results were obtained; however, there was a sex by vigorous PA interaction, such that vigorous PA was associated with height only in the girls. These data are consistent with the hypothesis that the bone mass and height of growing youths are positively influenced by higher dietary intake of energy and dairy foods, along with sufficient amounts of vigorous PA. This hypothesis needs to be tested in randomized controlled trials.

  11. Tree height-diameter allometry across the United States.

    Science.gov (United States)

    Hulshof, Catherine M; Swenson, Nathan G; Weiser, Michael D

    2015-03-01

    The relationship between tree height and diameter is fundamental in determining community and ecosystem structure as well as estimates of biomass and carbon storage. Yet our understanding of how tree allometry relates to climate and whole organismal function is limited. We used the Forest Inventory and Analysis National Program database to determine height-diameter allometries of 2,976,937 individuals of 293 tree species across the United States. The shape of the allometric relationship was determined by comparing linear and nonlinear functional forms. Mixed-effects models were used to test for allometric differences due to climate and floristic (between angiosperms and gymnosperms) and functional groups (leaf habit and shade tolerance). Tree allometry significantly differed across the United States largely because of climate. Temperature, and to some extent precipitation, in part explained tree allometric variation. The magnitude of allometric variation due to climate, however, had a phylogenetic signal. Specifically, angiosperm allometry was more sensitive to differences in temperature compared to gymnosperms. Most notably, angiosperm height was more negatively influenced by increasing temperature variability, whereas gymnosperm height was negatively influenced by decreasing precipitation and increasing altitude. There was little evidence to suggest that shade tolerance influenced tree allometry except for very shade-intolerant trees which were taller for any given diameter. Tree allometry is plastic rather than fixed and scaling parameters vary around predicted central tendencies. This allometric variation provides insight into life-history strategies, phylogenetic history, and environmental limitations at biogeographical scales.

  12. Body composition at birth and height at 2 years

    DEFF Research Database (Denmark)

    Admassu, Bitiya; Wells, Jonathan C; Girma, Tsinuel

    2017-01-01

    -free mass (FFM) were measured using air-displacement plethysmography within 48 h of birth. Linear regression models were applied to study the relationship between BC at birth and HAZ at 24 months (±3 months). RESULTS: A total of 268 children with height assessment at 2 years were included. Mean±s.d. HAZ...... at 2 years of age was -1.2±1.2, with 25.8% classified as stunted (HAZFFM at birth was positively associated with HAZ at 2 years, independent of length at birth. When adjusted for potential confounders, HAZ at 2 years was 0.73 higher for each additional kg FFM at birth (β=0.73, 95%CI (0.08, 1.......38). FM was not associated with HAZ at 2 years in any model. CONCLUSION: The FFM component of birth weight, independent of length, explains variability in HAZ at 2 years. Further studies are required to explore how changes in early infant BC are associated with linear growth.Pediatric Research accepted...

  13. Development of computer software to analyze entire LANDSAT scenes and to summarize classification results of variable-size polygons

    Science.gov (United States)

    Turner, B. J. (Principal Investigator); Baumer, G. M.; Myers, W. L.; Sykes, S. G.

    1981-01-01

    The Forest Pest Management Division (FPMD) of the Pennsylvania Bureau of Forestry has the responsibility for conducting annual surveys of the State's forest lands to accurately detect, map, and appraise forest insect infestations. A standardized, timely, and cost-effective method of accurately surveying forests and their condition should enhance the probability of suppressing infestations. The repetitive and synoptic coverage provided by LANDSAT (formerly ERTS) makes such satellite-derived data potentially attractive as a survey medium for monitoring forest insect damage over large areas. Forest Pest Management Division personnel have expressed keen interest in LANDSAT data and have informally cooperated with NASA/Goddard Space Flight Center (GSFC) since 1976 in the development of techniques to facilitate their use. The results of this work indicate that it may be feasible to use LANDSAT digital data to conduct annual surveys of insect defoliation of hardwood forests.

  14. Influence of real and virtual heights on standing balance.

    Science.gov (United States)

    Cleworth, Taylor W; Horslen, Brian C; Carpenter, Mark G

    2012-06-01

    Fear and anxiety induced by threatening scenarios, such as standing on elevated surfaces, have been shown to influence postural control in young adults. There is also a need to understand how postural threat influences postural control in populations with balance deficits and risk of falls. However, safety and feasibility issues limit opportunities to place such populations in physically threatening scenarios. Virtual reality (VR) has successfully been used to simulate threatening environments, although it is unclear whether the same postural changes can be elicited by changes in virtual and real threat conditions. Therefore, the purpose of this study was to compare the effects of real and virtual heights on changes to standing postural control, electrodermal activity (EDA) and psycho-social state. Seventeen subjects stood at low and high heights in both real and virtual environments matched in scale and visual detail. A repeated measures ANOVA revealed increases with height, independent of visual environment, in EDA, anxiety, fear, and center of pressure (COP) frequency, and decreases with height in perceived stability, balance confidence and COP amplitude. Interaction effects were seen for fear and COP mean position; where real elicited larger changes with height than VR. This study demonstrates the utility of VR, as simulated heights resulted in changes to postural, autonomic and psycho-social measures similar to those seen at real heights. As a result, VR may be a useful tool for studying threat related changes in postural control in populations at risk of falls, and to screen and rehabilitate balance deficits associated with fear and anxiety. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Characterizing the variability in chemical composition of flowback and produced waters - results from lab and field studies

    Science.gov (United States)

    Vieth-Hillebrand, Andrea; Wilke, Franziska D. H.; Schmid, Franziska E.; Zhu, Yaling; Lipińska, Olga; Konieczyńska, Monika

    2017-04-01

    The huge volumes and unknown composition of flowback and produced waters cause major public concerns about the environmental and social compatibility of hydraulic fracturing and the exploitation of gas from unconventional reservoirs. Flowback and produced waters contain not only residues of fracking additives but also chemical species that are dissolved from the target shales themselves. Shales are a heterogeneous mixture of minerals, organic matter, and formation water and little is actually understood about the fluid-rock interactions occurring during hydraulic fracturing of the shales and their effects on the chemical composition of flowback and produced water. To overcome this knowledge gap, interactions of different shales with different artificial stimulation fluids were studied in lab experiments under ambient and elevated temperature and pressure conditions. These lab experiments showed clearly that fluid-rock interactions change the chemical composition of the initial stimulation fluid and that geochemistry of the fractured shale is relevant for understanding flowback water composition. In addition, flowback water samples were taken after hydraulic fracturing of one horizontal well in Pomeranian region, Poland and investigated for their chemical composition. With this presentation, results from lab and field studies will be presented and compared to decipher possible controls on chemical compositions of flowback and produced water.

  16. Superflux chlorophyll-a analysis: An assessment of variability in results introduced prior to fluorometric analysis. [chesapeake bay and shelf regions

    Science.gov (United States)

    Cibik, S. J.; Rutledge, C. K.; Robertson, C. N.

    1981-01-01

    Several experiments were undertaken to identify variability in results that came from procedural differences in the processing of chlorophyll samples prior to fluorometric analysis. T-tests on group means indicated that significant differences (alpha = 0.05) in phaeopigment a concentrations did result in samples not initially screened, but not in the chlorophyll a concentrations. Highly significant differences (alpha = 0.001) in group means were found in samples which were held in acetone after filtering as compared to unfiltered seawater samples held for the same period. No difference in results was found between the 24-hour extraction and samples which were processed immediately.

  17. Influence of Vegetation Structure on Lidar-derived Canopy Height and Fractional Cover in Forested Riparian Buffers During Leaf-Off and Leaf-On Conditions

    Science.gov (United States)

    Wasser, Leah; Day, Rick; Chasmer, Laura; Taylor, Alan

    2013-01-01

    Estimates of canopy height (H) and fractional canopy cover (FC) derived from lidar data collected during leaf-on and leaf-off conditions are compared with field measurements from 80 forested riparian buffer plots. The purpose is to determine if existing lidar data flown in leaf-off conditions for applications such as terrain mapping can effectively estimate forested riparian buffer H and FC within a range of riparian vegetation types. Results illustrate that: 1) leaf-off and leaf-on lidar percentile estimates are similar to measured heights in all plots except those dominated by deciduous compound-leaved trees where lidar underestimates H during leaf off periods; 2) canopy height models (CHMs) underestimate H by a larger margin compared to percentile methods and are influenced by vegetation type (conifer needle, deciduous simple leaf or deciduous compound leaf) and canopy height variability, 3) lidar estimates of FC are within 10% of plot measurements during leaf-on periods, but are underestimated during leaf-off periods except in mixed and conifer plots; and 4) depth of laser pulse penetration lower in the canopy is more variable compared to top of the canopy penetration which may influence within canopy vegetation structure estimates. This study demonstrates that leaf-off lidar data can be used to estimate forested riparian buffer canopy height within diverse vegetation conditions and fractional canopy cover within mixed and conifer forests when leaf-on lidar data are not available. PMID:23382966

  18. Sub-Compartment Variation in Tree Height, Stem Diameter and Stocking in a Pinus radiata D. Don Plantation Examined Using Airborne LiDAR Data

    Directory of Open Access Journals (Sweden)

    Hanieh Saremi

    2014-08-01

    Full Text Available Better information regarding the spatial variability of height, Diameter at Breast Height (DBH and stocking could improve inventory estimates at the operational Planning Unit since these parameters are used extensively in allometric equations, including stem volume, biomass and carbon calculations. In this study, the influence of stand stocking on height and DBH of two even aged radiata pine (Pinus radiata D. Don stands were investigated using airborne Light Detection and Ranging (LiDAR data at a study site in New South Wales, Australia. Both stands were characterized by irregular stocking due to patchy establishment and self-thinning in the absence of any silvicultural thinning events. For the purpose of this study, a total of 34 plots from a 34 year old site and 43 plots from a nine year old site were established, from which a total of 447 trees were sampled. Within these plots, DBH and height measurements were measured and their relationships with stocking were evaluated. LiDAR was used for height estimation as well as stem counts in fixed plots (stocking. The results showed a significant relationship between stem DBH and stocking. At both locations, trees with larger diameters were found on lower stocking sites. Height values were also significantly correlated with stocking, with taller trees associated with high stocking. These results were further verified of additional tree samples, with independent field surveys for DBH and LiDAR-derived metrics for height analysis. This study confirmed the relationship between P. radiata tree heights and stem diameter with stocking and demonstrated the capacity of LiDAR to capture sub-compartment variation in these tree-level attributes.

  19. Determination of Vertical Datum Offset between the Regional and the Global Height Datum

    Directory of Open Access Journals (Sweden)

    LI Jiancheng

    2017-10-01

    Full Text Available The unification of the global height datum is a key problem to be solved for geodesy after the unification of global geodetic coordination system and three-dimension spatial datum, and the basis of global spatial information sharing and exchange. In this paper, the theoretical and practical problems of vertical datum offset between the regional height datum and the global height datum are studied. Based on the classical theory of the height system in physical geodesy, the definition of the height datum vertical offset is given, and the rigorous formulas for calculating the vertical offset are derived. The formulas can be used to deduce the three methods of the height datum vertical offset determination. On that basis, the influences of different reference system and reference ellipsoid parameters on the calculation of the vertical offset are analyzed. The results show that the reference system and the ellipsoid parameter conversion are very necessary. At the same time, the height anomaly differences method needs to consider the degree zero correction caused by the inconsistency between gravity potential of the global height datum and the one computed by the model. Based on potential difference approach and the height anomaly difference method, the vertical offset between the China 1985 national height datum and the global height datum corresponding to the normal gravity potential U0 of GRS80, WGS-84 and CGCS2000 reference ellipsoidal from the 152 GPS/leveling points near the origin of Qingdao height origin and the EGM2008, EIGEN-6C4 and SGG-UGM-1 model. The regional datum is 23.1 cm lower than the global datum based on EIGEN-6C4 and WGS-84. When the Gauss-Listing geoid (mean sea surface is selected as the global height datum, the China 1985 national height datum is 21.0 cm higher than the global height datum. The results also show that there are still large differences among the accuracies of the current gravity field models on these GPS

  20. The linkage between geopotential height and monthly precipitation in Iran

    Science.gov (United States)

    Shirvani, Amin; Fadaei, Amir Sabetan; Landman, Willem A.

    2018-04-01

    This paper investigates the linkage between large-scale atmospheric circulation and monthly precipitation during November to April over Iran. Canonical correlation analysis (CCA) is used to set up the statistical linkage between the 850 hPa geopotential height large-scale circulation and monthly precipitation over Iran for the period 1968-2010. The monthly precipitation dataset for 50 synoptic stations distributed in different climate regions of Iran is considered as the response variable in the CCA. The monthly geopotential height reanalysis dataset over an area between 10° N and 60° N and from 20° E to 80° E is utilized as the explanatory variable in the CCA. Principal component analysis (PCA) as a pre-filter is used for data reduction for both explanatory and response variables before applying CCA. The optimal number of principal components and canonical variables to be retained in the CCA equations is determined using the highest average cross-validated Kendall's tau value. The 850 hPa geopotential height pattern over the Red Sea, Saudi Arabia, and Persian Gulf is found to be the major pattern related to Iranian monthly precipitation. The Pearson correlation between the area averaged of the observed and predicted precipitation over the study area for Jan, Feb, March, April, November, and December months are statistically significant at the 5% significance level and are 0.78, 0.80, 0.82, 0.74, 0.79, and 0.61, respectively. The relative operating characteristic (ROC) indicates that the highest scores for the above- and below-normal precipitation categories are, respectively, for February and April and the lowest scores found for December.

  1. Do "big guys" really die younger? An examination of height and lifespan in former professional basketball players.

    Science.gov (United States)

    Lemez, Srdjan; Wattie, Nick; Baker, Joseph

    2017-01-01

    While factors such as genetics may mediate the relationship between height and mortality, evidence suggests that larger body size may be an important risk indicator of reduced lifespan longevity in particular. This study critically examined this relationship in professional basketball players. We examined living and deceased players who have played in the National Basketball Association (debut between 1946-2010) and/or the American Basketball Association (1967-1976) using descriptive and Kaplan-Meier and Cox regression analyses. The cut-off date for death data collection was December 11, 2015. Overall, 3,901 living and deceased players were identified and had a mean height of 197.78 cm (± 9.29, Range: 160.02-231.14), and of those, 787 former players were identified as deceased with a mean height of 193.88 cm (± 8.83, Range: 167.6-228.6). Descriptive findings indicated that the tallest players (top 5%) died younger than the shortest players (bottom 5%) in all but one birth decade (1941-1950). Similarly, survival analyses showed a significant relationship between height and lifespan longevity when both dichotomizing [χ2 (1) = 13.04, p < .05] and trichotomizing [χ2 (2) = 18.05, p < .05] the predictor variable height per birth decade, where taller players had a significantly higher mortality risk compared to shorter players through median (HR: 1.30, 95% CI: 1.13-1.50, p < .05) and trichotomized tertile split (HR: 1.40, 95% CI: 1.18-1.68, p <. 05; tallest 33.3% compared to shortest 33.3%) analyses. The uniqueness of examining the height-longevity hypothesis in this relatively homogeneous sub-population should be considered when interpreting these results. Further understanding of the potential risks of early mortality can help generate discourse regarding potential at-risk cohorts of the athlete population.

  2. Five-class height-weight mean and SD system applying Estonian reference values of height-weight mean and SD for systematization of seventeen-year-old conscripts' anthropometric data.

    Science.gov (United States)

    Lintsi, Mart; Kaarma, Helje; Aunapuu, Marina; Arend, Andres

    2007-03-01

    A study of 739 conscripts aged 17 years from the town of Tartu and from the Tartu county was performed. Height, weight, 33 anthropometric measurements and 12 skinfolds were measured. The data were classified into five height-weight mean and SD-classes applying the Estonian reference values for this age and sex (Grünberg et al. 1998). There were 3 classes with conformity between height and weight class: 1--small (small height and small weight), 2--medium (medium height and medium weight), 3--large (large height and large weight), 4--weight class dominating (pyknomorphic) and 5--height class dominating (leptomorphic). It was found, that in classes 1, 2 and 3 the height and weight increase was in accordance with the increase in all heights, breadths and depths, circumferences, skinfolds, body fat, muscle and bone mass. In class 4 circumferences, skinfolds, body fat and muscle mass were bigger. In class 5 all heights and the relative bone mass were bigger. The present investigation confirms the assumption that the five height-weight mean and SD five-class system applying the Estonian reference values for classifying the anthropometric variables is suitable for seventeen-year-old conscripts. As well the border values of 5%, 50% and 95% for every anthropometrical variable in the five-classes were calculated, which may be helpful for practical classifying.

  3. Estimation of Height from Arm Span in 6-11 Years Children in Odisha, India

    Directory of Open Access Journals (Sweden)

    Snigdha Prava Mishra

    2017-10-01

    Full Text Available Introduction: Standing height is an important anthropometric parameter to track longitudinal growth, to estimate body fatness and to calculate energy requirement. Measurement of height may be difficult in children who cannot stand. Aim: To establish regression equation for estimation of height from arm span in children. To check comparative relevancy of this equation with fixed height-to-arm span ratio (HAR for estimation of height. Materials and Methods: A cross-sectional study was conducted with 6-11 years school children (n=1465, Boys=774, Girls=691 in state of Odisha, India. Height was measured by portable stadiometer and arm span was measured by fiberglass measuring tape to nearest 0.1 cm. Pearson correlation and regression analysis was carried out between height and arm span data. p<0.05 (two tail was considered statistically significant. Results: Mean height and arm span in boys (124.16±8.74 cm and 125.57±10.43 cm respectively was significantly more (p<0.001 than height and arm span in girls (121.18±10.37 cm and 121.50±11.68 cm respectively. Mean HAR was 0.9942±0.0279. Correlation between height and arm span in boys was r = 0.94 (p<0.001 and in girls was r = 0.96 (p<0.001. Overall correlation coefficient was r = 0.95 (p<0.001. Regression equation for estimation of height from arm span was established: Height (cm = 0.8192 * arm span (cm + 21.46. Conclusion: Height in children of 6-11 years showed strong positive correlation with arm span. Regression equation established from this study can be used to estimate height from arm span. This estimation is more reliable than estimation of height from HAR.

  4. Anatomic variables affecting interdental papilla

    Directory of Open Access Journals (Sweden)

    Swapna A. Mahale

    2013-01-01

    Full Text Available Aim: The aim of this study is to evaluate the anatomic variables affecting the interdental papilla. Materials and Methods: Thirty adult patients were evaluated. Papilla score (PS, tooth form/shape, gingival thickness, crest bone height and keratinized gingiva/attached gingiva were recorded for 150 inter proximal sites. Data were analyzed using SPSS software package (version 7.0 and the significance level was set at 95% confidence interval. Pearson′s correlation was applied to correlate the relationship between the factors and the appearance of the papilla. Results: Competent papillae (complete fill interdentally were associated with: (1 Crown width (CW: length ≥0.87; (2 bone crest-contact point ≤5 mm; and (3 inter proximal gingival tissue thickness ≥1.5 mm. Gingival thickness correlated negatively with PS (r = −0.37 to −0.54 and positively with tissue height (r = 0.23-0.43. Tooth form (i.e., CW to length ratio correlated negatively with PS (r = −0.37 to −0.61. Conclusion: Gingival papilla appearance was associated significantly with tooth form/shape, crestal bone height and interproximal gingival thickness.

  5. Global effects of income and income inequality on adult height and sexual dimorphism in height.

    Science.gov (United States)

    Bogin, Barry; Scheffler, Christiane; Hermanussen, Michael

    2017-03-01

    Average adult height of a population is considered a biomarker of the quality of the health environment and economic conditions. The causal relationships between height and income inequality are not well understood. We analyze data from 169 countries for national average heights of men and women and national-level economic factors to test two hypotheses: (1) income inequality has a greater association with average adult height than does absolute income; and (2) neither income nor income inequality has an effect on sexual dimorphism in height. Average height data come from the NCD-RisC health risk factor collaboration. Economic indicators are derived from the World Bank data archive and include gross domestic product (GDP), Gross National Income per capita adjusted for personal purchasing power (GNI_PPP), and income equality assessed by the Gini coefficient calculated by the Wagstaff method. Hypothesis 1 is supported. Greater income equality is most predictive of average height for both sexes. GNI_PPP explains a significant, but smaller, amount of the variation. National GDP has no association with height. Hypothesis 2 is rejected. With greater average adult height there is greater sexual dimorphism. Findings support a growing literature on the pernicious effects of inequality on growth in height and, by extension, on health. Gradients in height reflect gradients in social disadvantage. Inequality should be considered a pollutant that disempowers people from the resources needed for their own healthy growth and development and for the health and good growth of their children. © 2017 Wiley Periodicals, Inc.

  6. Falls from heights in and around the city of Batman.

    Science.gov (United States)

    Al, Behçet; Yildirim, Cuma; Coban, Sacid

    2009-03-01

    We evaluated the demographic data, mortality rates, fall causes, and post-mortem findings of individuals who fell from heights. Five hundred thirty-eight patients who sustained injuries after an accidental fall from heights were entered into the study. Our cases were collected prospectively in Batman over a seven- month period. The mean age was 12.4+/-3.22 years (3 months-98 years); 56.5% of patients were under 6 years old and 83.5% were under 20 years old. The mean fall height was 3.2+/-2.4 m. The mortality rate was 2.2%, and was highest among the patients who fell from flat-roofed houses. The most common injuries were to the head, and 100% of those who died had a head injury. Six patients were followed because of abdominal bleeding and 141 patients due to extremity fractures; 6.7% of patients were operated on and 83.8% of patients were treated in the emergency department. The results of this study were at variance with literature data with respect to the following: falls from heights were most common in the 0-5 years of age group. Craniocerebral trauma is the most common injury in fatal falls. Males had a higher rate of falls from height than females.

  7. Comparison of mixing height parameterizations with profiles measurements

    Energy Technology Data Exchange (ETDEWEB)

    Jaquier, A.; Stuebi, R.; Tercier, P. [Swiss Meteorological Inst., SMI - MeteoSwiss, Payerne (Switzerland)

    1997-10-01

    Different meteorological pre-processors for dispersion studies are available to derive the atmospheric boundary layer mixing height (MH). The analysis of their performances has been reviewed in the framework of the European COST Action 710. In this project, the computed mixing height values have been compared with data derived mostly from aero-logical sounding analysis and Sodar measurements. Since then, a new analysis of a low-tropospheric wind profiler (WP) data has been performed taking advantage of its high data sampling ({delta}t {approx} 30 sec.). The comparison between these recent results and aero-logical sounding, Sodar data, as well as to meteorological pre-processors calculations are reported for three periods of several days corresponding to different meteorological situations. In convective conditions, the pre-processors give reasonable level, the mixing height growing rate is in fair agreement with the measured one. In stable cloudy daytime conditions, the modeled mixing height does not correspond to any measured height. (LN)

  8. Physiological pattern of lumbar disc height; Physiologisches Muster lumbaler Bandscheibenhoehen

    Energy Technology Data Exchange (ETDEWEB)

    Biggemann, M [Radiologische Klinik des Evangelischen Krankenhauses Bethesda, Duisburg (Germany); Frobin, W; Brinckmann, P [Muenster Univ. (Germany). Inst. fuer Experimentelle Biomechanik

    1997-07-01

    Purpose of this study is to present a new method of quantifying objectively the height of all discs in lateral radiographs of the lumbar spine and of analysing the normal craniocaudal sequence pattern of lumbar disc heights. Methods: The new parameter is the ventrally measured disc height corrected for the dependence on the angle of lordosis by normalisation to mean angles observed in the erect posture of healthy persons. To eliminate radiographic magnification, the corrected ventral height is related to the mean depth of the cranially adjoining vertebra. In this manner lumbar disc heights were objectively measured in young, mature and healthy persons (146 males and 65 females). The craniocaudal sequence pattern was analysed by mean values from all persons and by height differences of adjoining discs in each individual lumbar spine. Results: Mean normative values demonstrated an increase in disc height between L1/L2 and L4/L5 and a constant or decreasing disc height between L4/L5 and L5/S1. However, this `physiological sequence of disc height in the statistical mean` was observed in only 36% of normal males and 55% of normal females. Conclusion: The radiological pattern of the `physiological sequence of lumbar disc height` leads to a relevant portion of false positive pathological results especially at L4/L5. An increase of disc height from L4/L5 to L5/S1 may be normal. The recognition of decreased disc height should be based on an abrupt change in the heights of adjoining discs and not on a deviation from a craniocaudal sequence pattern. (orig.) [Deutsch] Ziel dieser Arbeit ist es, einen neuen Parameter zur objektiven Messung der Hoehen aller auf einer seitlichen Uebersichtsaufnahme der LWS erkennbaren Bandscheiben vorzustellen und die physiologische kraniokaudale Diskushoehensequenz neu zu dokumentieren. Methode: Bei dem neuen Messverfahren wird die Bandscheibenhoehe ventral gemessen, zur Korrektur ihrer Haltungsabhaengigkeit auf Standardwinkel (mittlere Winkel

  9. Measuring the height-to-height correlation function of corrugation in suspended graphene

    International Nuclear Information System (INIS)

    Kirilenko, D.A.; Brunkov, P.N.

    2016-01-01

    Nanocorrugation of 2D crystals is an important phenomenon since it affects their electronic and mechanical properties. The corrugation may have various sources; one of them is flexural phonons that, in particular, are responsible for the thermal conductivity of graphene. A study of corrugation of just the suspended graphene can reveal much of valuable information on the physics of this complicated phenomenon. At the same time, the suspended crystal nanorelief can hardly be measured directly because of high flexibility of the 2D crystal. Moreover, the relief portion related to rapid out-of-plane oscillations (flexural phonons) is also inaccessible by such measurements. Here we present a technique for measuring the Fourier components of the height–height correlation function H(q) of suspended graphene which includes the effect of flexural phonons. The technique is based on the analysis of electron diffraction patterns. The H(q) is measured in the range of wavevectors q≈0.4–4.5 nm"−"1. At the upper limit of this range H(q) does follow the T/κq"4 law. So, we measured the value of suspended graphene bending rigidity κ=1.2±0.4 eV at ambient temperature T≈300 K. At intermediate wave vectors, H(q) follows a slightly weaker exponent than theoretically predicted q"−"3"."1"5 but is closer to the results of the molecular dynamics simulation. At low wave vectors, the dependence becomes even weaker, which may be a sign of influence of charge carriers on the dynamics of undulations longer than 10 nm. The technique presented can be used for studying physics of flexural phonons in other 2D materials. - Highlights: • A technique for measuring free-standing 2D crystal corrugation is proposed. • The height-to-height correlation function of the suspended graphene corrugation is measured. • Various parameters of the intrinsic graphene properties are experimentally determined.

  10. Forensic Physics 101: Falls from a height

    Science.gov (United States)

    Cross, Rod

    2008-09-01

    The physics of falling from a height, a topic that could be included in a course on forensic physics or in an undergraduate class as an example of Newton's laws, is applied to a common forensic problem.

  11. Estimating Mixing Heights Using Microwave Temperature Profiler

    Science.gov (United States)

    Nielson-Gammon, John; Powell, Christina; Mahoney, Michael; Angevine, Wayne

    2008-01-01

    A paper describes the Microwave Temperature Profiler (MTP) for making measurements of the planetary boundary layer thermal structure data necessary for air quality forecasting as the Mixing Layer (ML) height determines the volume in which daytime pollution is primarily concentrated. This is the first time that an airborne temperature profiler has been used to measure the mixing layer height. Normally, this is done using a radar wind profiler, which is both noisy and large. The MTP was deployed during the Texas 2000 Air Quality Study (TexAQS-2000). An objective technique was developed and tested for estimating the ML height from the MTP vertical temperature profiles. In order to calibrate the technique and evaluate the usefulness of this approach, estimates from a variety of measurements during the TexAQS-2000 were compared. Estimates of ML height were used from radiosondes, radar wind profilers, an aerosol backscatter lidar, and in-situ aircraft measurements in addition to those from the MTP.

  12. U.S. Geoid Heights (GEOID96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for the conterminous United States is the GEOID96 model. The computation used about 1.8 million terrestrial and marine gravity data held in...

  13. PR/VI Geoid Heights (GEOID96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for Puerto Rico and the Virgin Islands is distributed as a GEOID96 model. The computation used 26,000 terrestrial and marine gravity data...

  14. Principal Hawaiian Islands Geoid Heights (GEOID96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' geoid height grid for the Principal Hawaiian Islands is distributed as a GEOID96 model. The computation used 61,000 terrestrial and marine gravity data held...

  15. Climatology and evolution of the mixing height over water

    Energy Technology Data Exchange (ETDEWEB)

    Sempreviva, A.M. [Istituto di Fisica dell`Atmosfera, CNR, Rome (Italy); Grynig, S.E. [Risoe National Lab., Roskilde (Denmark)

    1997-10-01

    In this paper we present results from an experimental investigation on the height of the mixed layer h, using a meteorological station located on the Danish island of Anholt. The station was operational for two years from September 1990 to October 1992. We present the analysis of two years of radio-sounding showing the average daily evolution of h. Furthermore observations of the mixed layer growth under near-neutral and unstable atmospheric conditions during six consecutive days has been modelled using a simple zero-order mixed-layer height model. Finally we have compared the evolution of the mixing height from the model with the evolution of the correlation coefficient between temperature and humidity to study the influence of the deepness of the convective layer on the mechanism of the correlation between temperature and humidity in the surface layer. (au)

  16. Vowel Height Allophony and Dorsal Place Contrasts in Cochabamba Quechua.

    Science.gov (United States)

    Gallagher, Gillian

    2016-01-01

    This paper reports on the results of two studies investigating the role of allophony in cueing phonemic contrasts. In Cochabamba Quechua, the uvularvelar place distinction is often cued by additional differences in the height of the surrounding vowels. An acoustic study documents the lowering effect of a preceding tautomorphemic or a following heteromorphemic uvular on the high vowels /i u/. A discrimination study finds that vowel height is a significant cue to the velar-uvular place contrast. These findings support a view of contrasts as collections of distinguishing properties, as opposed to oppositions in a single distinctive feature. © 2016 S. Karger AG, Basel.

  17. The importance of postural cues for determining eye height in immersive virtual reality.

    Science.gov (United States)

    Leyrer, Markus; Linkenauger, Sally A; Bülthoff, Heinrich H; Mohler, Betty J

    2015-01-01

    In human perception, the ability to determine eye height is essential, because eye height is used to scale heights of objects, velocities, affordances and distances, all of which allow for successful environmental interaction. It is well understood that eye height is fundamental to determine many of these percepts. Yet, how eye height itself is provided is still largely unknown. While the information potentially specifying eye height in the real world is naturally coincident in an environment with a regular ground surface, these sources of information can be easily divergent in similar and common virtual reality scenarios. Thus, we conducted virtual reality experiments where we manipulated the virtual eye height in a distance perception task to investigate how eye height might be determined in such a scenario. We found that humans rely more on their postural cues for determining their eye height if there is a conflict between visual and postural information and little opportunity for perceptual-motor calibration is provided. This is demonstrated by the predictable variations in their distance estimates. Our results suggest that the eye height in such circumstances is informed by postural cues when estimating egocentric distances in virtual reality and consequently, does not depend on an internalized value for eye height.

  18. The importance of postural cues for determining eye height in immersive virtual reality.

    Directory of Open Access Journals (Sweden)

    Markus Leyrer

    Full Text Available In human perception, the ability to determine eye height is essential, because eye height is used to scale heights of objects, velocities, affordances and distances, all of which allow for successful environmental interaction. It is well understood that eye height is fundamental to determine many of these percepts. Yet, how eye height itself is provided is still largely unknown. While the information potentially specifying eye height in the real world is naturally coincident in an environment with a regular ground surface, these sources of information can be easily divergent in similar and common virtual reality scenarios. Thus, we conducted virtual reality experiments where we manipulated the virtual eye height in a distance perception task to investigate how eye height might be determined in such a scenario. We found that humans rely more on their postural cues for determining their eye height if there is a conflict between visual and postural information and little opportunity for perceptual-motor calibration is provided. This is demonstrated by the predictable variations in their distance estimates. Our results suggest that the eye height in such circumstances is informed by postural cues when estimating egocentric distances in virtual reality and consequently, does not depend on an internalized value for eye height.

  19. Usefulness of the Mobile Virtual Reality Self-Training for Overcoming a Fear of Heights.

    Science.gov (United States)

    Hong, Yeon-Ju; Kim, Hesun Erin; Jung, Young Hoon; Kyeong, Sunghyon; Kim, Jae-Jin

    2017-12-01

    A mobile virtual reality system, equipped with built-in variables such as heart rate (HR), gaze-down data, and subjective fear rating, can allow individuals with a fear of heights to overcome it by self-training. This study aimed to verify the efficacy and safety of the training program. Forty-eight volunteers completed the four-session self-training program over 2 weeks. They were allocated into either low- or high-fear group by the Acrophobia Questionnaire (AQ)-anxiety scores, and then the changes of the built-in variables and AQ-anxiety scores were analyzed between the groups. The safety was assessed using the Simulator Sickness Questionnaire (SSQ). The AQ-anxiety scores were significantly decreased after self-training in both groups, and the degree of decrease was significantly greater in the high-fear group than in the low-fear group. Gaze-down percentage and subjective fear rating showed a significant group difference, but HR did not. The SSQ scores were within the acceptable level. These results suggest that the training effect was greater in the high-fear group than in the low-fear group. This mobile program may be safely applicable to self-training for individuals with high scores on the fear of heights by repeated exposure to virtual environments with the embedded feedback system.

  20. Evaluation of skeletal and dental age using third molar calcification, condylar height and length of the mandibular body.

    Science.gov (United States)

    Kedarisetty, Sunil Gupta; Rao, Guttikonda Venkateswara; Rayapudi, Naveen; Korlepara, Rajani

    2015-01-01

    To identify the most reliable method for age estimation among three variables, that is, condylar height, length of mandibular body and third molar calcification by Demirjian's method. Orthopantomograms and lateral cephalograms of 60 patients with equal gender ratio were included in the study, among each gender 15 subjects were below 18 years and 15 subjects were above 18 years. Lateral cephalograms were traced, height of condyle and mandibular body are measured manually on the tracing paper, OPG's were observed on radiographic illuminator and maturity score of third molar calcification was noted according to Demirjian's method. All the measurements were subjected to statistical analysis. The results obtained are of no significant difference between estimated age and actual age with all three parameters (P > 0.9780 condylar height, P > 0.9515 length of mandibular body, P > 0.8611 third molar calcification). Among these three, length of mandibular body shows least standard error test (i.e. 0.188). Although all three parameters can be used for age estimation, length of mandibular body is more reliable followed by height of condyle and third molar calcification.

  1. Output pulse height distribution of the GM counters

    International Nuclear Information System (INIS)

    Zhang Songshou; Xiong Jianping

    1995-01-01

    The GM counters are the radiation detectors most in use. It has special advantages compared with other detectors. This paper introduces the output pulse height distribution of the GM counters, gives the measuring instruments and methods. The measuring results, some discussions, and useful conclusion are given as well

  2. An attempt to link the Brazilian Height System to a World Height System

    Directory of Open Access Journals (Sweden)

    V. G. Ferreira

    Full Text Available This paper deals with the geopotential approach to investigate the present Brazilian Height System (BHS. Geopotential numbers are derived from Global Positioning System (GPS satellite surveying and disturbing potential on selected benchmarks. A model for the disturbing potential can be obtained by an existing set of spherical harmonic coefficients such as the Earth Gravity Model 2008 (EGM08. The approach provides absolute evaluation of local normal geopotential numbers (aka spheropotential numbers related to a so-called World Height System (WHS. To test the validity of the proposed methodology, a numerical experiment was carried out related to a test region in Southern Brazil. The accuracy of the derived geopotential numbers was tested versus local normal geopotential numbers based on 262 GPS/leveling points. The root mean square error (RMSE value for metric offset of BHS derived from geopotential numbers and the disturbing potential modeling in the test area was estimated to be near 0.224 meters in the absolute view. Therefore, since these spheropotential numbers are referred to a local datum, these results of comparisons may be an indicator of the mean bias of local network due to the effect of local Sea Surface Topography (SSTop and possible offset between the unknown reference for the BHS and the quasigeoid model in the region.

  3. Bali, Shaded Relief and Colored Height

    Science.gov (United States)

    2004-01-01

    The volcanic nature of the island of Bali is evident in this shaded relief image generated with data from the Shuttle Radar Topography Mission (SRTM).Bali, along with several smaller islands, make up one of the 27 Provinces of Indonesia. It lies over a major subduction zone where the Indo-Australian tectonic plate collides with the Sunda plate, creating one of the most volcanically active regions on the planet.The most significant feature on Bali is Gunung Agung, the symmetric, conical mountain at the right-center of the image. This 'stratovolcano,' 3,148 meters (10,308 feet) high, is held sacred in Balinese culture, and last erupted in 1963 after being dormant and thought inactive for 120 years. This violent event resulted in over 1,000 deaths, and coincided with a purification ceremony called Eka Dasa Rudra, meant to restore the balance between nature and man. This most important Balinese rite is held only once per century, and the almost exact correspondence between the beginning of the ceremony and the eruption is though to have great religious significance.Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot

  4. Sinai Peninsula, Shaded Relief and Colored Height

    Science.gov (United States)

    2004-01-01

    The Sinai Peninsula, located between Africa and Asia, is a result of those two continents pulling apart from each other. Earth's crust is cracking, stretching, and lowering along the two northern branches of the Red Sea, namely the Gulf of Suez, seen here on the west (left), and the Gulf of Aqaba, seen to the east (right). This color-coded shaded relief image shows the triangular nature of the peninsula, with the coast of the Mediterranean Sea forming the northern side of the triangle. The Suez Canal can be seen as the narrow vertical blue line in the upper left connecting the Red Sea to the Mediterranean. The peninsula is divided into three distinct parts; the northern region consisting chiefly of sandstone, plains and hills, the central area dominated by the Tih Plateau, and the mountainous southern region where towering peaks abound. Much of the Sinai is deeply dissected by river valleys, or wadis, that eroded during an earlier geologic period and break the surface of the plateau into a series of detached massifs with a few scattered oases. Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed

  5. Birth order progressively affects childhood height.

    Science.gov (United States)

    Savage, Tim; Derraik, José G B; Miles, Harriet L; Mouat, Fran; Cutfield, Wayne S; Hofman, Paul L

    2013-09-01

    There is evidence suggesting that first-born children and adults are anthropometrically different to later-borns. Thus, we aimed to assess whether birth order was associated with changes in growth and metabolism in childhood. We studied 312 healthy prepubertal children: 157 first-borns and 155 later-borns. Children were aged 3-10 years, born 37-41 weeks gestation, and of birth weight appropriate-for-gestational-age. Clinical assessments included measurement of children's height, weight, fasting lipid and hormonal profiles and DEXA-derived body composition. First-borns were taller than later-borns (P < 0·0001), even when adjusted for parents' heights (0·31 vs 0·03 SDS; P = 0·001). There was an incremental height decrease with increasing birth order, so that first-borns were taller than second-borns (P < 0·001), who were in turn taller than third-borns (P = 0·007). Further, among sibling pairs both height SDS (P = 0·009) and adjusted height SDS (P < 0·0001) were lower in second- vs first-born children. Consistent with differences in stature, first- (P = 0·043) and second-borns (P = 0·003) had higher IGF-I concentrations than third-borns. Both first- (P < 0·001) and second-borns (P = 0·004) also had reduced abdominal adiposity (lower android fat to gynoid fat ratio) when compared with third-borns. Other parameters of adiposity and blood lipids were unaffected by birth order. First-borns were taller than later-born children, with an incremental height reduction from first to third birth order. These differences were present after correction for genetic height, and associated to some extent with alterations in plasma IGF-I. Our findings strengthen the evidence that birth order is associated with phenotypic changes in childhood. © 2013 John Wiley & Sons Ltd.

  6. [Is olfactory function impaired in moderate height?].

    Science.gov (United States)

    Kühn, M; Welsch, H; Zahnert, T; Hummel, Thomas

    2009-09-01

    The human sense of smell seems to be influenced by the surrounding barometric pressure. These factors appear to be especially important during flights, for example, in order to recognize the smell of fire etc. Thus, questions are whether pilots or passengers exhibit an impaired smell sensitivity when tested at moderate heights, or, whether changes in humidity would affect the sense of smell. Using climate chambers, odor discrimination and butanol odor thresholds were tested in 77 healthy normosmic volunteers (5 female, 72 male; aged 25+/-8 years from 18 up to 53 years) under hypobaric (2 700+/-20 m, 20 degrees C+/-1 K, rh=50+/-5%) and hyperbaric, (10+/-0.5 m (2 bar)) and different humidity conditions (30 vs. 80%, 20 degrees C+/-1 K, normobaric). During all conditions cognitive performance was tested. Among other effects, olfactory sensitivity was impaired at threshold, but not suprathreshold level, in a hypobaric compared to a hyperbaric milieu, and thresholds were lower in humid, compared to relatively dry conditions. In conclusion, environmental conditions modulate the sense of smell, and may, consecutively, influence results from olfactory tests. During flight hypobaric conditions, mild hypoxia and dry air may cause impaired sensitivity of smell. Georg Thieme Verlag KG Stuttgart * New York.

  7. Subexponential estimates in Shirshov's theorem on height

    International Nuclear Information System (INIS)

    Belov, Aleksei Ya; Kharitonov, Mikhail I

    2012-01-01

    Suppose that F 2,m is a free 2-generated associative ring with the identity x m =0. In 1993 Zelmanov put the following question: is it true that the nilpotency degree of F 2,m has exponential growth? We give the definitive answer to Zelmanov's question by showing that the nilpotency class of an l-generated associative algebra with the identity x d =0 is smaller than Ψ(d,d,l), where Ψ(n,d,l)=2 18 l(nd) 3log 3 (nd)+13 d 2 . This result is a consequence of the following fact based on combinatorics of words. Let l, n and d≥n be positive integers. Then all words over an alphabet of cardinality l whose length is not less than Ψ(n,d,l) are either n-divisible or contain x d ; a word W is n-divisible if it can be represented in the form W=W 0 W 1 …W n so that W 1 ,...,W n are placed in lexicographically decreasing order. Our proof uses Dilworth's theorem (according to V.N. Latyshev's idea). We show that the set of not n-divisible words over an alphabet of cardinality l has height h 87 l·n 12log 3 n+48 . Bibliography: 40 titles.

  8. Variability in creep and rupture test results in a single heat of type 304 stainless steel. R and D report LR:75:4213-01:3

    International Nuclear Information System (INIS)

    Leyda, W.E.; Schultz, C.C.

    1975-09-01

    Results of uniaxial creep and rupture tests, from a single heat of type 304 stainless steel, are examined to determine the reasons for their greater-than-expected variability. The test results were obtained as part of a program to develop and verify high temperature structural design methods for liquid metal fast breeder reactor system components. A single heat of material (heat 9T2796) is being used throughout the program, by all investigators and in several product forms, to minimize the problem of heat-to-heat variations in elevated temperature behavior. The same laboratory reanneal was specified for each product form to reduce differences in behavior among the several being used. The data discussed was obtained from the 5/8-inch diameter, hot-rolled bar product form. The laboratory reanneal was performed after finish machining to minimize specimen-to-specimen differences. In spite of these efforts to reduce data variability, significant scatter was observed in both short-time and long-time deformation response, and also in time-to-rupture results

  9. Relationships Between Countermovement Jump Ground Reaction Forces and Jump Height, Reactive Strength Index, and Jump Time.

    Science.gov (United States)

    Barker, Leland A; Harry, John R; Mercer, John A

    2018-01-01

    Barker, LA, Harry, JR, and Mercer, JA. Relationships between countermovement jump ground reaction forces and jump height, reactive strength index, and jump time. J Strength Cond Res 32(1): 248-254, 2018-The purpose of this study was to determine the relationship between ground reaction force (GRF) variables to jump height, jump time, and the reactive strength index (RSI). Twenty-six, Division-I, male, soccer players performed 3 maximum effort countermovement jumps (CMJs) on a dual-force platform system that measured 3-dimensional kinetic data. The trial producing peak jump height was used for analysis. Vertical GRF (Fz) variables were divided into unloading, eccentric, amortization, and concentric phases and correlated with jump height, RSI (RSI = jump height/jump time), and jump time (from start to takeoff). Significant correlations were observed between jump height and RSI, concentric kinetic energy, peak power, concentric work, and concentric displacement. Significant correlations were observed between RSI and jump time, peak power, unload Fz, eccentric work, eccentric rate of force development (RFD), amortization Fz, amortization time, second Fz peak, average concentric Fz, and concentric displacement. Significant correlations were observed between jump time and unload Fz, eccentric work, eccentric RFD, amortization Fz, amortization time, average concentric Fz, and concentric work. In conclusion, jump height correlated with variables derived from the concentric phase only (work, power, and displacement), whereas Fz variables from the unloading, eccentric, amortization, and concentric phases correlated highly with RSI and jump time. These observations demonstrate the importance of countermovement Fz characteristics for time-sensitive CMJ performance measures. Researchers and practitioners should include RSI and jump time with jump height to improve their assessment of jump performance.

  10. Height and Body Composition Determine Arm Propulsive Force in Youth Swimmers Independent of a Maturation Stage

    OpenAIRE

    Moura, Tatiane; Costa, Manoel; Oliveira, Saulo; Júnior, Marcos Barbosa; Ritti-Dias, Raphael; Santos, Marcos

    2014-01-01

    The aim of this study was to examine the relationship between anthropometric variables, body composition and propulsive force in swimmers aged 9–17 years. Anthropometric characteristics (body height and mass, sitting height, arm span, arm muscle area and body composition) and the propulsive force of the arm (tethered swimming test) were evaluated in 56 competitive male swimmers. Tanner’s stages of genital maturation (P1–5) were used. The data analysis included correlations and multiple linear...

  11. Estimating fog-top height through near-surface micrometeorological measurements

    OpenAIRE

    Román Cascón, Carlos; Yagüe Anguis, Carlos; Steeneveld, Gert-Jan; Sastre, Mariano; Arrillaga, Jon Ander; Maqueda Burgos, Gregorio

    2016-01-01

    Fog-top height (fog thickness) is very useful information for aircraft maneuvers, data assimilation/validation of Numerical Weather Prediction models or nowcasting of fog dissipation. This variable is usually difficult to determine, since the fog-layer top cannot be observed from the surface. In some cases, satellite data, ground remote sensing instruments or atmospheric soundings are used to provide approximations of fog-top height. These instruments are expensive and their data not always a...

  12. Three modes of interdecadal trends in sea surface temperature and sea surface height

    Science.gov (United States)

    Gnanadesikan, A.; Pradal, M.

    2013-12-01

    It might be thought that sea surface height and sea surface temperature would be tightly related. We show that this is not necessarily the case on a global scale. We analysed this relationship in a suite of coupled climate models run under 1860 forcing conditions. The models are low-resolution variants of the GFDL Earth System Model, reported in Galbraith et al. (J. Clim. 2011). 1. Correlated changes in global sea surface height and global sea surface temperature. This mode corresponds to opening and closing of convective chimneys in the Southern Ocean. As the Southern Ocean destratifies, sea ice formation is suppressed during the winter and more heat is taken up during the summer. This mode of variability is highly correlated with changes in the top of the atmosphere radiative budget and weakly correlated with changes in the deep ocean circulation. 2. Uncorrelated changes in global sea surface height and global sea surface temperature. This mode of variability is associated with interdecadal variabliity in tropical winds. Changes in the advective flux of heat to the surface ocean play a critical role in driving these changes, which also result in significant local changes in sea level. Changes sea ice over the Southern Ocean still result in changes in solar absorption, but these are now largely cancelled by changes in outgoing longwave radiation. 3. Anticorrelated changes in global sea surface height and global sea surface temperatures. By varying the lateral diffusion coefficient in the ocean model, we are able to enhance and suppress convection in the Southern and Northern Pacific Oceans. Increasing the lateral diffusion coefficients shifts the balance sources of deep water away from the warm salty deep water of the North Atlantic and towards cold fresh deep water from the other two regions. As a result, even though the planet as a whole warms, the deep ocean cools and sea level falls, with changes of order 30 cm over 500 years. The increase in solar absorption

  13. Two-dimensional transport of dust from an infinite line source at ground level: non-zero roughness height

    International Nuclear Information System (INIS)

    Hassan, M.H.A.; Eltayeb, I.A.

    1992-07-01

    The previous study (Eltayeb and Hassan, 1992) of the two-dimensional diffusion equation of dust over a rough ground surface, which acts as a dust source of variable strength, under the influence of horizontal wind and gravitational attraction is here extended to all finite values of the roughness height Z 0 . An analytic expression is obtained for the concentration of dust for a general strength of the source. The result reduces to the previously known solutions as special cases. The expression for the concentration has been evaluated for some representative example of the source strength g(X). It is found that the concentration decreases with roughness height at any fixed point above ground level. (author). 4 refs, 2 figs

  14. Spatio-temporal evaluation of plant height in corn via unmanned aerial systems

    Science.gov (United States)

    Varela, Sebastian; Assefa, Yared; Vara Prasad, P. V.; Peralta, Nahuel R.; Griffin, Terry W.; Sharda, Ajay; Ferguson, Allison; Ciampitti, Ignacio A.

    2017-07-01

    Detailed spatial and temporal data on plant growth are critical to guide crop management. Conventional methods to determine field plant traits are intensive, time-consuming, expensive, and limited to small areas. The objective of this study was to examine the integration of data collected via unmanned aerial systems (UAS) at critical corn (Zea mays L.) developmental stages for plant height and its relation to plant biomass. The main steps followed in this research were (1) workflow development for an ultrahigh resolution crop surface model (CSM) with the goal of determining plant height (CSM-estimated plant height) using data gathered from the UAS missions; (2) validation of CSM-estimated plant height with ground-truthing plant height (measured plant height); and (3) final estimation of plant biomass via integration of CSM-estimated plant height with ground-truthing stem diameter data. Results indicated a correlation between CSM-estimated plant height and ground-truthing plant height data at two weeks prior to flowering and at flowering stage, but high predictability at the later growth stage. Log-log analysis on the temporal data confirmed that these relationships are stable, presenting equal slopes for both crop stages evaluated. Concluding, data collected from low-altitude and with a low-cost sensor could be useful in estimating plant height.

  15. Impact of acquisition and interpretation on total inter-observer variability in echocardiography: results from the quality assurance program of the STAAB cohort study.

    Science.gov (United States)

    Morbach, Caroline; Gelbrich, Götz; Breunig, Margret; Tiffe, Theresa; Wagner, Martin; Heuschmann, Peter U; Störk, Stefan

    2018-02-14

    Variability related to image acquisition and interpretation is an important issue of echocardiography in clinical trials. Nevertheless, there is no broadly accepted standard method for quality assessment of echocardiography in clinical research reports. We present analyses based on the echocardiography quality-assurance program of the ongoing STAAB cohort study (characteristics and course of heart failure stages A-B and determinants of progression). In 43 healthy individuals (mean age 50 ± 14 years; 18 females), duplicate echocardiography scans were acquired and mutually interpreted by one of three trained sonographers and an EACVI certified physician, respectively. Acquisition (AcV), interpretation (InV), and inter-observer variability (IOV; i.e., variability between the acquisition-interpretation sequences of two different observers), were determined for selected M-mode, B-mode, and Doppler parameters. We calculated Bland-Altman upper 95% limits of absolute differences, implying that 95% of measurement differences were smaller/equal to the given value: e.g. LV end-diastolic volume (mL): 25.0, 25.0, 27.9; septal e' velocity (cm/s): 3.03, 1.25, 3.58. Further, 90, 85, and 80% upper limits of absolute differences were determined for the respective parameters. Both, acquisition and interpretation, independently and sizably contributed to IOV. As such, separate assessment of AcV and InV is likely to aid in echocardiography training and quality-assurance. Our results further suggest to routinely determine IOV in clinical trials as a comprehensive measure of imaging quality. The derived 95, 90, 85, and 80% upper limits of absolute differences are suggested as reproducibility targets of future studies, thus contributing to the international efforts of standardization in quality-assurance.

  16. Adult height and risk of breast cancer: a possible effect of early nutrition

    OpenAIRE

    Nilsen, T I Lund; Vatten, L J

    2001-01-01

    The relationship of breast cancer to early reproductive development and height suggests that fetal and childhood nutrition may be important in its aetiology. Caloric restriction sufficient to reduce adult height may reduce breast cancer risk. During World War II (WWII) there was a marked reduction in average caloric intake in Norway that resulted in greater nutritional diversity. We hypothesized that a positive association between height and risk of breast cancer would be stronger among women...

  17. Retrieval of savanna vegetation canopy height from ICESat-GLAS spaceborne LiDAR with terrain correction

    CSIR Research Space (South Africa)

    Khalefa, E

    2013-11-01

    Full Text Available variability (slope) and canopy height within the GLAS footprints. The canopy height retrievals were validated with field observations in 23 GLAS footprints and show that the direct method works well over flat areas (Pearson correlation coefficient r = 0.70, p...

  18. Capim-braquiária sob lotação contínua e com altura única ou variável durante as estações do ano: morfogênese e dinâmica de tecidos Signalgrass under continuous stocking with fixed or variable height during the seasons: morphogenesis and dynamics of tissues

    Directory of Open Access Journals (Sweden)

    Manoel Eduardo Rozalino Santos

    2011-11-01

    25 cm no início da primavera.This study was conducted to identify effective strategies for grazing managing of Brachiaria decumbens cv. Basilisk, under continuous stocking, based on assessments of their morphogenetic and structural characteristics. Two strategies of grazing management were studied: in one, the grass was maintained with 25-cm mean height throughout the experimental period, and in the other, it was 15 cm during the winter, rising to 25 cm from the beginning of spring. The split-plot in randomized block design with four replications was adopted. The strategies of grazing management responded to primary factor, characterized by average heights of pastures during the seasons (winter, spring and summer. The seasons corresponded to secondary factor and consisted of measures over the experimental period. Pasture's lowering to 15 cm in the winter resulted in higher leaf appearance rate (0.02 leaves/tiller.day and higher number of live leaves (4.5 leaves/tiller in the winter. However, this management strategy lowered leaf lifespan (66 days, leaf senescence rate (0.22 cm/tiller.day, and length of leaf lamina (11 cm and stem (15.2 cm in winter months, in relation to pasture with 25 cm. During this season, rates of leaf appearance (0.06 leaves/tiller.day, leaf elongation (0.110 cm/tiller.day stem elongation (0.008 cm/tiller.day, live leaves (2.9 leaves/tiller, length of leaf lamina (8.6 cm and stem (13.5 cm lowered. On the other hand, leaf lifespan (139 days and number of dead leaves (2.0 leaves/tiller were higher. The highest leaf senescence rate occurred in the spring (0.40 cm/tiller.day. The B. decumbens cv. Basilisk pasture under continuous stocking can be managed on a seasonal basis, with decrease to 15 cm in early winter, and further increase to 25 cm in early spring.

  19. Comparison of dust-layer heights from active and passive satellite sensors

    Science.gov (United States)

    Kylling, Arve; Vandenbussche, Sophie; Capelle, Virginie; Cuesta, Juan; Klüser, Lars; Lelli, Luca; Popp, Thomas; Stebel, Kerstin; Veefkind, Pepijn

    2018-05-01

    Aerosol-layer height is essential for understanding the impact of aerosols on the climate system. As part of the European Space Agency Aerosol_cci project, aerosol-layer height as derived from passive thermal and solar satellite sensors measurements have been compared with aerosol-layer heights estimated from CALIOP measurements. The Aerosol_cci project targeted dust-type aerosol for this study. This ensures relatively unambiguous aerosol identification by the CALIOP processing chain. Dust-layer height was estimated from thermal IASI measurements using four different algorithms (from BIRA-IASB, DLR, LMD, LISA) and from solar GOME-2 (KNMI) and SCIAMACHY (IUP) measurements. Due to differences in overpass time of the various satellites, a trajectory model was used to move the CALIOP-derived dust heights in space and time to the IASI, GOME-2 and SCIAMACHY dust height pixels. It is not possible to construct a unique dust-layer height from the CALIOP data. Thus two CALIOP-derived layer heights were used: the cumulative extinction height defined as the height where the CALIOP extinction column is half of the total extinction column, and the geometric mean height, which is defined as the geometrical mean of the top and bottom heights of the dust layer. In statistical average over all IASI data there is a general tendency to a positive bias of 0.5-0.8 km against CALIOP extinction-weighted height for three of the four algorithms assessed, while the fourth algorithm has almost no bias. When comparing geometric mean height there is a shift of -0.5 km for all algorithms (getting close to zero for the three algorithms and turning negative for the fourth). The standard deviation of all algorithms is quite similar and ranges between 1.0 and 1.3 km. When looking at different conditions (day, night, land, ocean), there is more detail in variabilities (e.g. all algorithms overestimate more at night than during the day). For the solar sensors it is found that on average SCIAMACHY data

  20. New Closed-Form Results on Ordered Statistics of Partial Sums of Gamma Random Variables and its Application to Performance Evaluation in the Presence of Nakagami Fading

    KAUST Repository

    Nam, Sung Sik

    2017-06-19

    Complex wireless transmission systems require multi-dimensional joint statistical techniques for performance evaluation. Here, we first present the exact closed-form results on order statistics of any arbitrary partial sums of Gamma random variables with the closedform results of core functions specialized for independent and identically distributed Nakagami-m fading channels based on a moment generating function-based unified analytical framework. These both exact closed-form results have never been published in the literature. In addition, as a feasible application example in which our new offered derived closed-form results can be applied is presented. In particular, we analyze the outage performance of the finger replacement schemes over Nakagami fading channels as an application of our method. Note that these analysis results are directly applicable to several applications, such as millimeter-wave communication systems in which an antenna diversity scheme operates using an finger replacement schemes-like combining scheme, and other fading scenarios. Note also that the statistical results can provide potential solutions for ordered statistics in any other research topics based on Gamma distributions or other advanced wireless communications research topics in the presence of Nakagami fading.

  1. Cytomegalovirus sequence variability, amplicon length, and DNase-sensitive non-encapsidated genomes are obstacles to standardization and commutability of plasma viral load results.

    Science.gov (United States)

    Naegele, Klaudia; Lautenschlager, Irmeli; Gosert, Rainer; Loginov, Raisa; Bir, Katia; Helanterä, Ilkka; Schaub, Stefan; Khanna, Nina; Hirsch, Hans H

    2018-04-22

    Cytomegalovirus (CMV) management post-transplantation relies on quantification in blood, but inter-laboratory and inter-assay variability impairs commutability. An international multicenter study demonstrated that variability is mitigated by standardizing plasma volumes, automating DNA extraction and amplification, and calibration to the 1st-CMV-WHO-International-Standard as in the FDA-approved Roche-CAP/CTM-CMV. However, Roche-CAP/CTM-CMV showed under-quantification and false-negative results in a quality assurance program (UK-NEQAS-2014). To evaluate factors contributing to quantification variability of CMV viral load and to develop optimized CMV-UL54-QNAT. The UL54 target of the UK-NEQAS-2014 variant was sequenced and compared to 329 available CMV GenBank sequences. Four Basel-CMV-UL54-QNAT assays of 361 bp, 254 bp, 151 bp, and 95 bp amplicons were developed that only differed in reverse primer positions. The assays were validated using plasmid dilutions, UK-NEQAS-2014 sample, as well as 107 frozen and 69 prospectively collected plasma samples from transplant patients submitted for CMV QNAT, with and without DNase-digestion prior to nucleic acid extraction. Eight of 43 mutations were identified as relevant in the UK-NEQAS-2014 target. All Basel-CMV-UL54 QNATs quantified the UK-NEQAS-2014 but revealed 10-fold increasing CMV loads as amplicon size decreased. The inverse correlation of amplicon size and viral loads was confirmed using 1st-WHO-International-Standard and patient samples. DNase pre-treatment reduced plasma CMV loads by >90% indicating the presence of unprotected CMV genomic DNA. Sequence variability, amplicon length, and non-encapsidated genomes obstruct standardization and commutability of CMV loads needed to develop thresholds for clinical research and management. Besides regular sequence surveys, matrix and extraction standardization, we propose developing reference calibrators using 100 bp amplicons. Copyright © 2018 Elsevier B.V. All

  2. The association between Helicobacter pylori infection and adult height

    International Nuclear Information System (INIS)

    Moayyedi, Paul; Forman, David; Duffett, Sara; Mason, Su; Brown, Julia; Crocombe, Will; Feltbower, Richard; Axon, Anthony

    2005-01-01

    Objectives: A cross-sectional survey was performed to evaluate the association between H. pylori and adult height. Methods: H. pylori infection was assessed using a 13 C-urea breath test and height measured by a research nurse using a stadiometer in participants between the ages of 40-49 years. Results: Height was measured in 2932/3682 participants that attended and were evaluable. H. pylori infected women were 1.4 cm shorter than uninfected women (95% confidence interval, CI=0.7-2.1 cm) and this statistically significant difference persisted after adjusting for age, ethnicity, childhood and present socio-economic status (H. pylori positives 0.79 cm shorter; 95%CI: 0.05-1.52 cm). H. pylori positive men were 0.7 cm shorter than uninfected men but this did not reach statistical significance (95% CI: -0.1-1.5 cm). Conclusion: Although H. pylori infection is associated with reduced adult height in women, this maybe due to residual confounding

  3. Inheritance of culm height and grain yield in durum wheat

    International Nuclear Information System (INIS)

    Filev, K.

    1984-01-01

    Results from a study of GA sensitive and GA insensitive durum wheat mutants and cultivars in relation with their culm height and 1000 grain weight are presented. With increasing culm height, the GA response also increased. A positive correlation between plant height and GA response was found. Crosses were made between durum wheats and the F 1 and F 2 progenies were analysed. A different inheritance in F 1 and segregation in F 2 was obtained in crosses of a semi-dwarf, GA insensitive [1] line with GA sensitive (S) lines differing in height, medium (93.2cm) and tall (133.5cm). In a reciprocal cross, semi-dwarf - I with medium - S, the semi-dwarf type was dominant in F 1 , suggesting that their semi-dwarfing genes were not allelic. When the semi-dwarf - I and tall - S were crossed an intermediate inheritance in F 1 was observed. In the F 2 generation from crosses semi-dwarf - I with medium - S with semi-dwarf - I, a phenotypic dihybred segregation 9:3:3:1 was observed. In crosses semi-dwarf - I with tall - S different variation curves were obtained. Semi-dwarfs with high productivity were observed in F 2 , a fact indicating that lodging resistant lines with high yields could be selected. (author)

  4. HEIGHT VARIATION OF THE VECTOR MAGNETIC FIELD IN SOLAR SPICULES

    Energy Technology Data Exchange (ETDEWEB)

    Suárez, D. Orozco; Ramos, A. Asensio; Bueno, J. Trujillo, E-mail: dorozco@iac.es [Instituto de Astrofísica de Canarias, E-38205 La Laguna, Tenerife (Spain)

    2015-04-20

    Proving the magnetic configuration of solar spicules has hitherto been difficult due to the lack of spatial resolution and image stability during off-limb ground-based observations. We report spectropolarimetric observations of spicules taken in the He i 1083 nm spectral region with the Tenerife Infrared Polarimeter II at the German Vacuum Tower Telescope of the Observatorio del Teide (Tenerife, Canary Islands, Spain). The data provide the variation with geometrical height of the Stokes I, Q, U, and V profiles, whose encoded information allows the determination of the magnetic field vector by means of the HAZEL inversion code. The inferred results show that the average magnetic field strength at the base of solar spicules is about 80 gauss, and then it decreases rapidly with height to about 30 gauss at a height of 3000 km above the visible solar surface. Moreover, the magnetic field vector is close to vertical at the base of the chromosphere and has mid-inclinations (about 50°) above 2 Mm height.

  5. An investigation of cloud base height in Chiang Mai

    Science.gov (United States)

    Peengam, S.; Tohsing, K.

    2017-09-01

    Clouds play very important role in the variation of surface solar radiation and rain formation. To understand this role, it is necessary to know the physical and geometrical of properties of cloud. However, clouds vary with location and time, which lead to a difficulty to obtain their properties. In this work, a ceilometer was installed at a station of the Royal Rainmaking and Agricultural Aviation Department in Chiang Mai (17.80° N, 98.43° E) in order to measure cloud base height. The cloud base height data from this instrument were compared with those obtained from LiDAR, a more sophisticated instrument installed at the same site. It was found that the cloud base height from both instruments was in reasonable agreement, with root mean square difference (RMSD) and mean bias difference (MBD) of 19.21% and 1.58%, respectively. Afterward, a six-month period (August, 2016-January, 2017) of data from the ceilometer was analyzed. The results show that mean cloud base height during this period is 1.5 km, meaning that most clouds are in the category of low-level cloud.

  6. Maternal height and child mortality in 42 developing countries.

    Science.gov (United States)

    Monden, Christiaan W S; Smits, Jeroen

    2009-01-01

    Previous research reports mixed results about the association between maternal height and child mortality. Some studies suggest that the negative association might be stronger in contexts with fewer resources. This hypothesis has yet not been tested in a cross-nationally comparative design. We use data on 307,223 children born to 194,835 women in 444 districts of 42 developing countries to estimate the association between maternal height and child mortality and test whether this association is modified by indicators at the level of the household (like sex, age and twin status of the child and socio-economic characteristics of the mother and her partner), district (regional level of development, public health facilities and female occupational attainment) and country (GDP per capita). We find a robust negative effect of logged maternal height on child mortality. The effect of maternal health is strongest for women with least education and is more important in the first year after birth and for twin births. The indicators of development at the district and country level do not modify the effect of maternal height. (c) 2008 Wiley-Liss, Inc.

  7. Effects of plant phenology and vertical height on accuracy of radio-telemetry locations

    Science.gov (United States)

    Grovenburg, Troy W.; Jacques, Christopher N.; Klaver, Robert W.; DePerno, Christopher S.; Lehman, Chad P.; Brinkman, Todd J.; Robling, Kevin A.; Rupp, Susan P.; Jenks, Jonathan A.

    2013-01-01

    The use of very high frequency (VHF) radio-telemetry remains wide-spread in studies of wildlife ecology and management. However, few studies have evaluated the influence of vegetative obstruction on accuracy in differing habitats with varying transmitter types and heights. Using adult and fawn collars at varying heights above the ground (0, 33, 66 and 100 cm) to simulate activities (bedded, feeding and standing) and ages (neonate, juvenile and adult) of deer Odocoileus spp., we collected 5,767 bearings and estimated 1,424 locations (28-30 for each of 48 subsamples) in three habitat types (pasture, grassland and forest), during two stages of vegetative growth (spring and late summer). Bearing error was approximately twice as large at a distance of 900 m for fawn (9.9°) than for adult deer collars (4.9°). Of 12 models developed to explain the variation in location error, the analysis of covariance model (HT*D + C*D + HT*TBA + C*TBA) containing interactions of height of collar above ground (HT), collar type (C), vertical height of understory vegetation (D) and tree basal area (TBA) was the best model (wi = 0.92) and explained ∼ 71% of the variation in location error. Location error was greater for both collar types at 0 and 33 cm above the ground compared to 66 and 100 cm above the ground; however, location error was less for adult than fawn collars. Vegetation metrics influenced location error, which increased with greater vertical height of understory vegetation and tree basal area. Further, interaction of vegetation metrics and categorical variables indicated significant effects on location error. Our results indicate that researchers need to consider study objectives, life history of the study animal, signal strength of collar (collar type), distance from transmitter to receiver, topographical changes in elevation, habitat composition and season when designing telemetry protocols. Bearing distances in forested habitat should be decreased (approximately 23

  8. The influence of recent climate change on tree height growth differs with species and spatial environment.

    Science.gov (United States)

    Messaoud, Yassine; Chen, Han Y H

    2011-02-16

    Tree growth has been reported to increase in response to recent global climate change in controlled and semi-controlled experiments, but few studies have reported response of tree growth to increased temperature and atmospheric carbon dioxide (CO₂) concentration in natural environments. This study addresses how recent global climate change has affected height growth of trembling aspen (Populus tremuloides Michx) and black spruce (Picea mariana Mill B.S.) in their natural environments. We sampled 145 stands dominated by aspen and 82 dominated by spruce over the entire range of their distributions in British Columbia, Canada. These stands were established naturally after fire between the 19th and 20th centuries. Height growth was quantified as total heights of sampled dominant and co-dominant trees at breast-height age of 50 years. We assessed the relationships between 50-year height growth and environmental factors at both spatial and temporal scales. We also tested whether the tree growth associated with global climate change differed with spatial environment (latitude, longitude and elevation). As expected, height growth of both species was positively related to temperature variables at the regional scale and with soil moisture and nutrient availability at the local scale. While height growth of trembling aspen was not significantly related to any of the temporal variables we examined, that of black spruce increased significantly with stand establishment date, the anomaly of the average maximum summer temperature between May-August, and atmospheric CO₂ concentration, but not with the Palmer Drought Severity Index. Furthermore, the increase of spruce height growth associated with recent climate change was higher in the western than in eastern part of British Columbia. This study demonstrates that the response of height growth to recent climate change, i.e., increasing temperature and atmospheric CO₂ concentration, did not only differ with tree species, but

  9. Radiotherapy alone in the treatment of uterine cervix cancer with telecobalt and low-dose-rate brachytherapy: retrospective analysis of results and variables

    International Nuclear Information System (INIS)

    Ferrigno, Robson; Campos de Oliveira Faria, Sergio Luis; Weltman, Eduardo; Salvajoli, Joao Victor; Segreto, Roberto Araujo; Pastore, Ayrton; Nadalin, Wladimir

    2003-01-01

    Purpose: This retrospective analysis aims to report results and variables from patients with cervix cancer treated by radiation therapy alone with telecobalt and low-dose-rate brachytherapy (LDRB). Methods and Materials: Between September 1989 and September 1995, 190 patients with histologic diagnosis of cervix carcinoma were treated with telecobalt for external beam radiotherapy (EBR), followed by one or two insertions of LDRB. Stage distribution according to patients was the following: IB, 12; IIA, 4; IIB, 105; and IIIB, 69. Median dose of EBR at whole pelvis was 40 Gy, and median parametrial doses for Stages II and III patients were 50 Gy and 60 Gy, respectively. Median doses of LDRB at point A for patients treated with one and two insertions were 38 Gy and 50 Gy, respectively. Results: Median follow-up time was 70 months (range: 8-127 months). Overall survival, disease-free survival, and 5-year local control of patients at Stages I, II, and III were 83%, 78%, and 46%; 83%, 82%, and 49%; and 92%, 87%, and 58%, respectively. Overall incidence of late complications in the rectum, small bowel, and urinary tract was 15.3% (19/190), 4.2% (8/190), and 6.8% (13/190), respectively. The actuarial 5-year rectal, small bowel, and urinary incidence of late complications was 16.1%, 4.6%, and 7.6%, respectively. Clinical stage was the only significant variable for overall 5-year survival (p = 0.001), for disease-free survival (p=0.001), and for local control (p=0.001). Stage II patients more than 50 years old had better disease-free survival and local control at 5 years (p=0.004). None of the analyzed variables influenced the actuarial 5-year incidence of late complications. Conclusions: Results of this series suggest that the use of telecobalt equipment for EBR with doses up to 50 Gy at whole pelvis, prior to brachytherapy, is an acceptable technique for radiation therapy alone in the treatment of cervix cancer, especially in developing countries, including Brazil, where

  10. Response of Plant Height, Species Richness and Aboveground Biomass to Flooding Gradient along Vegetation Zones in Floodplain Wetlands, Northeast China.

    Science.gov (United States)

    Lou, Yanjing; Pan, Yanwen; Gao, Chuanyu; Jiang, Ming; Lu, Xianguo; Xu, Y Jun

    2016-01-01

    Flooding regime changes resulting from natural and human activity have been projected to affect wetland plant community structures and functions. It is therefore important to conduct investigations across a range of flooding gradients to assess the impact of flooding depth on wetland vegetation. We conducted this study to identify the pattern of plant height, species richness and aboveground biomass variation along the flooding gradient in floodplain wetlands located in Northeast China. We found that the response of dominant species height to the flooding gradient depends on specific species, i.e., a quadratic response for Carex lasiocarpa, a negative correlation for Calamagrostis angustifolia, and no response for Carex appendiculata. Species richness showed an intermediate effect along the vegetation zone from marsh to wet meadow while aboveground biomass increased. When the communities were analysed separately, only the water table depth had significant impact on species richness for two Carex communities and no variable for C. angustifolia community, while height of dominant species influenced aboveground biomass. When the three above-mentioned communities were grouped together, variations in species richness were mainly determined by community type, water table depth and community mean height, while variations in aboveground biomass were driven by community type and the height of dominant species. These findings indicate that if habitat drying of these herbaceous wetlands in this region continues, then two Carex marshes would be replaced gradually by C. angustifolia wet meadow in the near future. This will lead to a reduction in biodiversity and an increase in productivity and carbon budget. Meanwhile, functional traits must be considered, and should be a focus of attention in future studies on the species diversity and ecosystem function in this region.

  11. Response of Plant Height, Species Richness and Aboveground Biomass to Flooding Gradient along Vegetation Zones in Floodplain Wetlands, Northeast China

    Science.gov (United States)

    Lou, Yanjing; Pan, Yanwen; Gao, Chuanyu; Jiang, Ming; Lu, Xianguo; Xu, Y. Jun

    2016-01-01

    Flooding regime changes resulting from natural and human activity have been projected to affect wetland plant community structures and functions. It is therefore important to conduct investigations across a range of flooding gradients to assess the impact of flooding depth on wetland vegetation. We conducted this study to identify the pattern of plant height, species richness and aboveground biomass variation along the flooding gradient in floodplain wetlands located in Northeast China. We found that the response of dominant species height to the flooding gradient depends on specific species, i.e., a quadratic response for Carex lasiocarpa, a negative correlation for Calamagrostis angustifolia, and no response for Carex appendiculata. Species richness showed an intermediate effect along the vegetation zone from marsh to wet meadow while aboveground biomass increased. When the communities were analysed separately, only the water table depth had significant impact on species richness for two Carex communities and no variable for C. angustifolia community, while height of dominant species influenced aboveground biomass. When the three above-mentioned communities were grouped together, variations in species richness were mainly determined by community type, water table depth and community mean height, while variations in aboveground biomass were driven by community type and the height of dominant species. These findings indicate that if habitat drying of these herbaceous wetlands in this region continues, then two Carex marshes would be replaced gradually by C. angustifolia wet meadow in the near future. This will lead to a reduction in biodiversity and an increase in productivity and carbon budget. Meanwhile, functional traits must be considered, and should be a focus of attention in future studies on the species diversity and ecosystem function in this region. PMID:27097325

  12. Height, fun and safety in the design of children's playground equipment.

    Science.gov (United States)

    Wakes, Sarah; Beukes, Amanda

    2012-01-01

    The study reported in this paper adopted a holistic design approach to investigate issues associated with height related playground injuries from a users' perspective. The main objective was to gain an understanding of the relationship between height and fun so as to establish practical guidelines for addressing the causes of height related injuries whilst maintaining the attributes of playground equipment that children find fun and challenging. Results show that, on the one hand, the risk of injury increases when height is coupled with the use of upper body strength and, on the other hand, that coordination is a greater source of fun and challenge than height for children. Accordingly, it is suggested that the level of risk of injury attached to children's playground equipment can be reduced when the use of lower body strength and coordination are combined with lower free fall heights.

  13. Agronomic characters and lodging resistance of plant height mutants of rice

    International Nuclear Information System (INIS)

    Zhang Zhonggui; Wu Yuejin; Liu Binmei; Xu Xue; Zhang Lili; Wang Min

    2010-01-01

    Fourteen plant height mutants of Nipponbare were used to study the effect of plant height on the agronomic characters and lodging resistance. The results indicated that the plant height was positively correlated with spike length, third internode length, height of gravity center, fresh weight of main stem, dry weight of main stem, thousand-grain weight, grain-yield per plant and biological yield, and the second internode length. Meanwhile, plant height played an important role in lodging resistance, it was significantly positively correlated with lodging index and negatively correlated with bending moment and culm type index. The correlation between agronomic characters and lodging resistance showed that several agronomic characters had strong impact on the lodging resistance, such as spike length, height of gravity center, basal internode length ( first and second internode), fresh and dry weight of main stem, dry weight of basal internode, seed setting, thousand-grain weight, grain-weight per plant and biological yield. (authors)

  14. The Effects of Microgravity on Seated Height (Spinal Elongation)

    Science.gov (United States)

    Young, K. S.; Rajulu, S.

    2011-01-01

    ABSTRACT Many physiological factors, such as spinal elongation, fluid shifts, bone atrophy, and muscle loss, occur during an exposure to a microgravity environment. Spinal elongation is just one of the factors that can also affect the safety and performance of a crewmember while in space. Spinal elongation occurs due to the lack of gravity/compression on the spinal column. This allows for the straightening of the natural spinal curve. There is a possible fluid shift in the inter-vertebral disks that may also result in changes in height. This study aims at collecting the overall change in seated height for crewmembers exposed to a microgravity environment. During previous Programs, Apollo-Soyuz Test Project (ASTP) and Skylab, spinal elongation data was collected from a small number of subjects in a standing posture but were limited in scope. Data from these studies indicated a quick increase in stature during the first few days of weightlessness, after which stature growth reached a plateau resulting in up to a 3% increase of the original measurement [1-5]. However, this data was collected only for crewmembers in standing posture and not in a seated posture. Seated height may have a different effect than standing height due to a change in posture as well as due to a compounded effect of wearing restraints and a potential compression of the gluteal area. Seated height was deemed as a critical measurement in the design of the Constellation Program s (CxP) Crew Exploration Vehicle (CEV), called Orion which is now the point-of-departure vehicle for the Multi-Purpose Crew Vehicle (MPCV) Program; therefore a better understanding of the effects of microgravity on seated height is necessary. Potential changes in seated height that may not have impacted crew accommodation in previous Programs will have significant effects on crew accommodation due to the layout of seats in the Orion.. The current and existing configuration is such that the four crewmembers are stacked two by

  15. Tree height and tropical forest biomass estimation

    Science.gov (United States)

    M.O. Hunter; M. Keller; D. Vitoria; D.C. Morton

    2013-01-01

    Tropical forests account for approximately half of above-ground carbon stored in global vegetation. However, uncertainties in tropical forest carbon stocks remain high because it is costly and laborious to quantify standing carbon stocks. Carbon stocks of tropical forests are determined using allometric relations between tree stem diameter and height and biomass....

  16. Falls from height: A retrospective analysis.

    Science.gov (United States)

    Turgut, Kasim; Sarihan, Mehmet Ediz; Colak, Cemil; Güven, Taner; Gür, Ali; Gürbüz, Sükrü

    2018-01-01

    Emergency services manage trauma patients frequently and falls from height comprise the main cause of emergency service admissions. In this study, we aimed to analyse the demographic characteristics of falls from height and their relationship to the mortality. A total of 460 patients, who admitted to the Emergency Department of Inonu University between November 2011 and November 2014 with a history of fall from height, were examined retrospectively. Demographic parameters, fall characteristics and their effect to mortality were evaluated statistically. The study comprised of 292 (63.5%) men and 168 (36.5%) women patients. The mean age of all patients was 27±24.99 years. Twenty-six (5.6%) patients died and the majority of them were in ≥62 years old group. The highest percentage of falls was at 0-5 years age group (28.3%). People fell mainly from 1.1-4 metres(m) level (46.1%). The causes of falls were ordered as unintentional (92.2%), workplace (8.1%) and suicidal (1.7%). Skin and soft tissue injuries (37.4%) were the main traumatic lesions. Age, fall height, fall place, lineer skull fracture, subarachnoidal hemorrhage, cervical fracture, thoracic vertebra fracture and trauma scores had statistically significant effect on mortality. The casualties died because of subarachnoid hemorrhage mostly.

  17. Optimizing height presentation for aircraft cockpit displays

    Science.gov (United States)

    Jordan, Chris S.; Croft, D.; Selcon, Stephen J.; Markin, H.; Jackson, M.

    1997-02-01

    This paper describes an experiment conducted to investigate the type of display symbology that most effectively conveys height information to users of head-down plan-view radar displays. The experiment also investigated the use of multiple information sources (redundancy) in the design of such displays. Subjects were presented with eight different height display formats. These formats were constructed from a control, and/or one, two, or three sources of redundant information. The three formats were letter coding, analogue scaling, and toggling (spatially switching the position of the height information from above to below the aircraft symbol). Subjects were required to indicate altitude awareness via a four-key, forced-choice keyboard response. Error scores and response times were taken as performance measures. There were three main findings. First, there was a significant performance advantage when the altitude information was presented above and below the symbol to aid the representation of height information. Second, the analogue scale, a line whose length indicated altitude, proved significantly detrimental to performance. Finally, no relationship was found between the number of redundant information sources employed and performance. The implications for future aircraft and displays are discussed in relation to current aircraft tactical displays and in the context of perceptual psychological theory.

  18. Evidence of inbreeding depression on human height

    NARCIS (Netherlands)

    R. McQuillan (Ruth); N. Eklund (Niina); N. Pirastu (Nicola); M. Kuningas (Maris); B.P. McEvoy (Brian); T. Esko (Tõnu); T. Corre (Tanguy); G. Davies (Gail); M. Kaakinen (Marika); L.-P. Lyytikäinen (Leo-Pekka); K. Kristiansson (Kati); A.S. Havulinna (Aki); M. Gögele (Martin); V. Vitart (Veronique); A. Tenesa (Albert); Y.S. Aulchenko (Yurii); C. Hayward (Caroline); A. Johansson (Åsa); M. Boban (Mladen); S. Ulivi (Shelia); A. Robino (Antonietta); V. Boraska (Vesna); W. Igl (Wilmar); S.H. Wild (Sarah); L. Zgaga (Lina); N. Amin (Najaf); E. Theodoratou (Evropi); O. Polasek (Ozren); S. Girotto; L.M. Lopez (Lorna); C. Sala (Cinzia); J. Lahti (Jari); T. Laatikainen (Tiina); I. Prokopenko (Inga); M. Kals (Mart); J. Viikari (Jorma); J. Yang (Joanna); A. Pouta (Anneli); K. Estrada Gil (Karol); A. Hofman (Albert); N.B. Freimer (Nelson); N.G. Martin (Nicholas); M. Kähönen (Mika); L. Milani (Lili); M. Heliovaara (Markku); E. Vartiainen (Erkki); K. Räikkönen (Katri); C. Masciullo (Corrado); J.M. Starr (John); A.A. Hicks (Andrew); L. Esposito (Laura); I. Kolcic (Ivana); S.M. Farrington (Susan); B.A. Oostra (Ben); T. Zemunik (Tatijana); H. Campbell (Harry); M. Kirin (Mirna); M. Pehlic (Marina); F. Faletra (Flavio); D.J. Porteous (David J.); G. Pistis (Giorgio); E. Widen (Elisabeth); V. Salomaa (Veikko); S. Koskinen (Seppo); K. Fischer (Krista); T. Lehtimäki (Terho); A.C. Heath (Andrew); M.I. McCarthy (Mark); F. Rivadeneira Ramirez (Fernando); G.W. Montgomery (Grant); H.W. Tiemeier (Henning); A.L. Hartikainen; P.A.F. Madden (Pamela); P. d' Adamo (Pio); N. Hastie (Nick); U. Gyllensten (Ulf); A.F. Wright (Alan); C.M. van Duijn (Cornelia); M.G. Dunlop (Malcolm); I. Rudan (Igor); P. Gasparini (Paolo); P.P. Pramstaller (Peter Paul); I.J. Deary (Ian); D. Toniolo (Daniela); K. Hagen (Knut); A. Jula (Antti); O. Raitakari (Olli); A. Metspalu (Andres); M. Perola (Markus); M.-R. Jarvelin (Marjo-Riitta); A.G. Uitterlinden (André); P.M. Visscher (Peter); J.F. Wilson (James)

    2012-01-01

    textabstractStature is a classical and highly heritable complex trait, with 80%-90% of variation explained by genetic factors. In recent years, genome-wide association studies (GWAS) have successfully identified many common additive variants influencing human height; however, little attention has

  19. Facial cues to perceived height influence leadership choices in simulated war and peace contexts.

    Science.gov (United States)

    Re, Daniel E; DeBruine, Lisa M; Jones, Benedict C; Perrett, David I

    2013-01-31

    Body size and other signs of physical prowess are associated with leadership hierarchies in many social species. Here we (1) assess whether facial cues associated with perceived height and masculinity have different effects on leadership judgments in simulated wartime and peacetime contexts and (2) test how facial cues associated with perceived height and masculinity influence dominance perceptions. Results indicate that cues associated with perceived height and masculinity in potential leaders‟ faces are valued more in a wartime (vs. peacetime) context. Furthermore, increasing cues of apparent height and masculinity in faces increased perceived dominance. Together, these findings suggest that facial cues of physical stature contribute to establishing leadership hierarchies in humans.

  20. Resonant Vibrations Resulting from the Re-Engineering of a Constant-Speed 2-Bladed Turbine to a Variable-Speed 3-Bladed Turbine

    Energy Technology Data Exchange (ETDEWEB)

    Fleming, P.; Wright, A. D.; Finersh, L. J.

    2010-12-01

    The CART3 (Controls Advanced Research Turbine, 3-bladed) at the National Wind Technology Center has recently been converted from a 2-bladed constant speed machine to a 3-bladed variable speed machine designed specically for controls research. The purpose of this conversion was to develop an advanced controls field-testing platform which has the more typical 3-bladed configuration. A result of this conversion was the emergence of several resonant vibrations, some of which initially prevented operation of the turbine until they could be explained and resolved. In this paper, the investigations into these vibrations are presented as 'lessons-learned'. Additionally, a frequency-domain technique called waterfall plotting is discussed and its usefulness in this research is illustrated.

  1. The Effect of NPP's Stack Height to Radiation Dose

    International Nuclear Information System (INIS)

    Pandi, Liliana Yetta; Rohman, Budi

    2003-01-01

    The purpose of dose calculation for accidents is to analyze the capability of NPP to maintain the safety of public and workers in case an accident occurs on the Plant in a site. This paper calculates the Loss of Coolant Accident in PWR plant. The calculation results shows that no risks of serious radiation exposure are given to the neighboring public even if such a large accident occurred, and the effect of stack height can be predicted by analysis of the calculation results. The whole dose is calculated for some location (100 m, 300 m, 500 m, 700 m, 900 m, 1500 m, and 2000 m) with three difference stack height i.e. 0 m, 40 m and 100 m. The result of the whole dose calculation is under permitted criteria for whole dose : 0.25 Sv and thyroid dose : 3.0 Sv. The calculation of radiation dose in this paper use EEDCDQ code

  2. Spatial variability and trends in Younger Dryas equilibrium line altitudes across the European Alps using a hypsometrically based ELA model: results and implications

    Science.gov (United States)

    Keeler, D. G.; Rupper, S.; Schaefer, J. M.; Finkel, R. C.; Maurer, J. M.

    2016-12-01

    Alpine glaciers constitute an important component of terrestrial paleoclimate records due to, among other characteristics, their high sensitivity to climate change, near global extent, and their integration of myriad climate variables into a single, easily detected signal. Because the glacier equilibrium line altitude (ELA) provides a more explicit representation of climate than many other glacier properties, ELA methods allow for more direct comparisons of multiple glaciers within or between regions. Such comparisons allow for more complete investigations of the ultimate causes of mountain glaciation during specific events. Many studies however tend to focus on a limited number of sites, and employ a large variety of different techniques for ELA reconstruction between studies, making wider climate implications more tenuous. Methods of ELA reconstruction that can be rapidly and consistently applied to an arbitrary number of paleo-glaciers would provide a more accurate portrayal of the changes in climate across a given region. Here we present ELA reconstructions from Egesen Stadial moraines across the European Alps using an ELA model accounting for differences in glacier width, glacier shape, bed topography, ice thickness, and glacier length, including several glaciers constrained to the Younger Dryas using surface exposure dating techniques. We compare reconstructed Younger Dryas ELA values to modern ELA values using the same model, or using end of summer snowline estimates where no glacier is currently present. We further provide uncertainty estimates on the ΔELA using bootstrapped Monte Carlo simulations for the various input parameters. Preliminary results compare favorably to previous glacier studies of the European Younger Dryas, but provide greater context from many glaciers across the region as a whole. Such results allow for a more thorough investigation of the spatial variability and trends in climate during the Younger Dryas across the European Alps, and

  3. Comparing Johnson’s SBB, Weibull and Logit-Logistic bivariate distributions for modeling tree diameters and heights using copulas

    Energy Technology Data Exchange (ETDEWEB)

    Cardil Forradellas, A.; Molina Terrén, D.M.; Oliveres, J.; Castellnou, M.

    2016-07-01

    Aim of study: In this study we compare the accuracy of three bivariate distributions: Johnson’s SBB, Weibull-2P and LL-2P functions for characterizing the joint distribution of tree diameters and heights. Area of study: North-West of Spain. Material and methods: Diameter and height measurements of 128 plots of pure and even-aged Tasmanian blue gum (Eucalyptus globulus Labill.) stands located in the North-west of Spain were considered in the present study. The SBB bivariate distribution was obtained from SB marginal distributions using a Normal Copula based on a four-parameter logistic transformation. The Plackett Copula was used to obtain the bivariate models from the Weibull and Logit-logistic univariate marginal distributions. The negative logarithm of the maximum likelihood function was used to compare the results and the Wilcoxon signed-rank test was used to compare the related samples of these logarithms calculated for each sample plot and each distribution. Main results: The best results were obtained by using the Plackett copula and the best marginal distribution was the Logit-logistic. Research highlights: The copulas used in this study have shown a good performance for modeling the joint distribution of tree diameters and heights. They could be easily extended for modelling multivariate distributions involving other tree variables, such as tree volume or biomass. (Author)

  4. An assimilation test of Doppler radar reflectivity and radial velocity from different height layers in improving the WRF rainfall forecasts

    Science.gov (United States)

    Tian, Jiyang; Liu, Jia; Yan, Denghua; Li, Chuanzhe; Chu, Zhigang; Yu, Fuliang

    2017-12-01

    Hydrological forecasts require high-resolution and accurate rainfall information, which is one of the most difficult variables to be captured by the mesoscale Numerical Weather Prediction (NWP) systems. Radar data assimilation is an effective method for improving rainfall forecasts by correcting the initial and lateral boundary conditions of the NWP system. The aim of this study is to explore an efficient way of utilizing the Doppler radar observations for data assimilation, which is implemented by exploring the effect of assimilating radar data from different height layers on the improvement of the NWP rainfall accuracy. The Weather Research and Forecasting (WRF) model is used for numerical rainfall forecast in the Zijingguan catchment located in the ;Jing-Jin-Ji; (Beijing-Tianjin-Hebei) Region of Northern China, and the three-dimensional variational data assimilation (3-DVar) technique is adopted to assimilate the radar data. Radar reflectivity and radial velocity are assimilated separately and jointly. Each type of radar data is divided into seven data sets according to the height layers: (1) 2000 m, and (7) all layers. The results show that radar reflectivity assimilation leads to better results than radial velocity assimilation. The accuracy of the forecasted rainfall deteriorates with the rise of the height of the assimilated radar reflectivity. The same results can be found when assimilating radar reflectivity and radial velocity at the same time. The conclusions of this study provide a reference for efficient assimilation of the radar data in improving the NWP rainfall products.

  5. Impact of growth hormone therapy on adult height of children with idiopathic short stature: systematic review.

    Science.gov (United States)

    Deodati, Annalisa; Cianfarani, Stefano

    2011-03-11

    To systematically determine the impact of growth hormone therapy on adult height of children with idiopathic short stature. Systematic review. Cochrane Central Register of Controlled Trials, Medline, and the bibliographic references from retrieved articles of randomised and non-randomised controlled trials from 1985 to April 2010. Height in adulthood (standard deviation score) and overall gain in height (SD score) from baseline measurement in childhood. Randomised and non-randomised controlled trials with height measurements for adults. Inclusion criteria were initial short stature (defined as height >2 SD score below the mean), peak growth hormone responses >10 μg/L, prepubertal stage, no previous growth hormone therapy, and no comorbid conditions that would impair growth. Adult height was considered achieved when growth rate was growth hormone treated children exceeded that of the controls by 0.65 SD score (about 4 cm). The mean height gain in treated children was 1.2 SD score compared with 0.34 SD score in untreated children. A slight difference of about 1.2 cm in adult height was observed between the two growth hormone dose regimens. In the seven non-randomised controlled trials the adult height of the growth hormone treated group exceeded that of the controls by 0.45 SD score (about 3 cm). Growth hormone therapy in children with idiopathic short stature seems to be effective in partially reducing the deficit in height as adults, although the magnitude of effectiveness is on average less than that achieved in other conditions for which growth hormone is licensed. The individual response to therapy is highly variable, and additional studies are needed to identify the responders.

  6. A stingless bee can use visual odometry to estimate both height and distance.

    Science.gov (United States)

    Eckles, M A; Roubik, D W; Nieh, J C

    2012-09-15

    Bees move and forage within three dimensions and rely heavily on vision for navigation. The use of vision-based odometry has been studied extensively in horizontal distance measurement, but not vertical distance measurement. The honey bee Apis mellifera and the stingless bee Melipona seminigra measure distance visually using optic flow-movement of images as they pass across the retina. The honey bees gauge height using image motion in the ventral visual field. The stingless bees forage at different tropical forest canopy levels, ranging up to 40 m at our site. Thus, estimating height would be advantageous. We provide the first evidence that the stingless bee Melipona panamica utilizes optic flow information to gauge not only distance traveled but also height above ground, by processing information primarily from the lateral visual field. After training bees to forage at a set height in a vertical tunnel lined with black and white stripes, we observed foragers that explored a new tunnel with no feeder. In a new tunnel, bees searched at the same height they were trained to. In a narrower tunnel, bees experienced more image motion and significantly lowered their search height. In a wider tunnel, bees experienced less image motion and searched at significantly greater heights. In a tunnel without optic cues, bees were disoriented and searched at random heights. A horizontal tunnel testing these variables similarly affected foraging, but bees exhibited less precision (greater variance in search positions). Accurately gauging flight height above ground may be crucial for this species and others that compete for resources located at heights ranging from ground level to the high tropical forest canopies.

  7. Detection of Chromosome X;18 Breakpoints and Translocation of the Xq22.3;18q23 Regions Resulting in Variable Fertility Phenotypes

    Directory of Open Access Journals (Sweden)

    Attila Szvetko

    2012-01-01

    Full Text Available We describe a familial pattern of gonosomal-autosomal translocation between the X and 18 chromosomes, balanced and unbalanced forms, in male and female siblings. The proposita was consulted for hypergonadotropic hypogonadism. Karyotype analysis revealed a balanced 46, X, t(X;18(q22.3;q23 genotype. The sister of the proband presented with oligomenorrhea with irregular menses and possesses an unbalanced form of the translocation 46, X, der(X, t(X;18(q22.3;q23. The brother of the proband was investigated and was found to possess the balanced form of the same translocation, resulting in disrupted spermatogenesis. Maternal investigation revealed the progenitor karyotype 46, X, t(X;18(q22.3;q23. Maternal inheritance and various genomic events contributed to the resultant genotypes. Primary infertility was initially diagnosed in all progeny; however, the male individual recently fathered twins. We briefly review the mechanisms associated with X;18 translocations and describe a pattern of inheritance, where breakpoints and translocation of the Xq22.3;18q23 regions have resulted in variable fertility.

  8. Bedform response to flow variability

    Science.gov (United States)

    Nelson, J.M.; Logan, B.L.; Kinzel, P.J.; Shimizu, Y.; Giri, S.; Shreve, R.L.; McLean, S.R.

    2011-01-01

    Laboratory observations and computational results for the response of bedform fields to rapid variations in discharge are compared and discussed. The simple case considered here begins with a relatively low discharge over a flat bed on which bedforms are initiated, followed by a short high-flow period with double the original discharge, during which the morphology of the bedforms adjusts, followed in turn by a relatively long period of the original low discharge. For the grain size and hydraulic conditions selected, the Froude number remains subcritical during the experiment, and sediment moves predominantly as bedload. Observations show rapid development of quasi-two-dimensional bedforms during the initial period of low flow with increasing wavelength and height over the initial low-flow period. When the flow increases, the bedforms rapidly increase in wavelength and height, as expected from other empirical results. When the flow decreases back to the original discharge, the height of the bedforms quickly decreases in response, but the wavelength decreases much more slowly. Computational results using an unsteady two-dimensional flow model coupled to a disequilibrium bedload transport model for the same conditions simulate the formation and initial growth of the bedforms fairly accurately and also predict an increase in dimensions during the high-flow period. However, the computational model predicts a much slower rate of wavelength increase, and also performs less accurately during the final low-flow period, where the wavelength remains essentially constant, rather than decreasing. In addition, the numerical results show less variability in bedform wavelength and height than the measured values; the bedform shape is also somewhat different. Based on observations, these discrepancies may result from the simplified model for sediment particle step lengths used in the computational approach. Experiments show that the particle step length varies spatially and

  9. Analysis of the nature of injuries in victims of fall from height

    Directory of Open Access Journals (Sweden)

    Magdalena E. Kusior

    2017-01-01

    Full Text Available Aim of study: To assess the types and extent of injuries sustained by victims of fall from height depending on the height of fall. Material and methods: The study included 338 bodies of victims of fatal falls from different heights (from the 1st to 10th floors who were subjected to medico-legal autopsy at the Department of Forensic Medicine, Jagiellonian University Medical College, between 1995 and 2014. For each individual, selected data were collected including gender, age, body height, injury types and presence of alcohol or other intoxicants in blood. The analysis comprised injuries to the brain, thoracic and abdominal organs, fractures of the skull, extremities, ribs and spine, and fractures of the scapula, clavicle and sternum (considered together. The study focused on determining the frequency of occurrence of different injuries in relation to one another and depending on the height of fall. Results : The number and extent of injuries was found to increase along with the height of fall. Three injury types, including injuries to the mesentery and both kidneys and fractures of upper extremity small bones, were shown to occur from the threshold heights of the 3rd, 4th and 6th floors. Eleven injuries demonstrated a statistically significant correlation with the height of fall. The study also revealed a number of correlations between the frequencies of occurrence of different injuries. Conclusions : Injuries found from the threshold value may suggest the minimal height of fall. The presence of injuries which correlate with increasing height, and the overall number of injuries observed in victims of fall from height, may be useful for inferring the height of the fall.

  10. The impact of growth hormone therapy on adult height in noonan syndrome: a systematic review.

    Science.gov (United States)

    Giacomozzi, Claudio; Deodati, Annalisa; Shaikh, Mohamad Guftar; Ahmed, Syed Faisal; Cianfarani, Stefano

    2015-01-01

    Recombinant human growth hormone (rhGH) is being used to promote linear growth in short children with Noonan syndrome. However, its efficacy is still controversial. To systematically determine the impact of rhGH therapy on adult height in children with Noonan syndrome. We searched the Cochrane Central Register of Controlled Trials, ISI Web of Science, MEDLINE, and the bibliographic references from all retrieved articles published until April 2014. Studies reporting adult/near-adult height in children with Noonan syndrome treated with rhGH or reporting at least a 3-year follow-up were analysed. Quality and strength of recommendation were assessed according to the Endocrine Society criteria. No controlled trials reporting adult height were available. Five studies were identified reporting adult height or near adult height. Data comparison showed inter-individual variability in the response to rhGH, mean height gain standard deviation score ranging between 0.6 and 1.4 according to national standards, and between 0.6 and 2 according to Noonan standards. Significant biases affected all the studies. High-quality controlled trials on the impact of rhGH therapy on adult height are lacking, and the robustness of available data is not sufficient to recommend such therapy in children with Noonan syndrome. © 2015 S. Karger AG, Basel.

  11. Physical growth of the shuar: Height, Weight, and BMI references for an indigenous amazonian population.

    Science.gov (United States)

    Urlacher, Samuel S; Blackwell, Aaron D; Liebert, Melissa A; Madimenos, Felicia C; Cepon-Robins, Tara J; Gildner, Theresa E; Snodgrass, J Josh; Sugiyama, Lawrence S

    2016-01-01

    Information concerning physical growth among small-scale populations remains limited, yet such data are critical to local health efforts and to foster basic understandings of human life history and variation in childhood development. Using a large dataset and robust modeling methods, this study aims to describe growth from birth to adulthood among the indigenous Shuar of Amazonian Ecuador. Mixed-longitudinal measures of height, weight, and body mass index (BMI) were collected from Shuar participants (n = 2,463; age: 0-29 years). Centile growth curves and tables were created for each anthropometric variable of interest using Generalized Additive Models for Location, Scale, and Shape (GAMLSS). Pseudo-velocity and Lambda-Mu-Sigma curves were generated to further investigate Shuar patterns of growth and to facilitate comparison with United States Center for Disease Control and Prevention and multinational World Health Organization growth references. The Shuar are small throughout life and exhibit complex patterns of growth that differ substantially from those of international references. Similar to other Amazonians, Shuar growth in weight compares more favorably to references than growth in height, resulting in BMI curves that approximate international medians. Several additional characteristics of Shuar development are noteworthy, including large observed variation in body size early in life, significant infant growth faltering, extended male growth into adulthood, and a markedly early female pubertal growth spurt in height. Phenotypic plasticity and genetic selection in response to local environmental factors may explain many of these patterns. Providing a detailed reference of growth for the Shuar and other Amazonian populations, this study possesses direct clinical application and affords valuable insight into childhood health and the ecology of human growth. © 2015 Wiley Periodicals, Inc.

  12. Comparative efficiency of wind turbines with different heights of rotor hubs: performance evaluation for Latvia

    International Nuclear Information System (INIS)

    Bezrukovs, V P; Zacepins, A J; Bezrukovs, V V

    2014-01-01

    Performance evaluation of wind turbines (WT) for different heights of the rotor hub is made based on the wind speed and direction data obtained in 2009–2013 on-shore in the north of Latvia using a LOGGER 9200 Symphonie measurement system mounted on a 60 m mast. Based on the measurement analysis results, wind speed distribution curves have been modelled for heights of up to 200 m using power and logarithmic (log) law approximation methods. The curves for the modelled Weibull's parameters are plotted in dependence on height. The efficiency comparison is made for different WT types taking into account the distribution of the wind energy potential in height in the Latvian territory. The annual electric energy production was calculated for the WTs with different heights of rotor hubs. In the calculations the technical data on the following WT types were used: E-3120 (50 kW, hub height 20.5/30.5/36.5/42.7 m), E-33 (330 kW, hub height 37/44/49/50 m), E-48 (800 kW, hub height 50/60/75 m) and E-82 (2.3 MW, hub height of 78/85/98/108/138 m)

  13. Effects of Wheelchair Seat-height Settings on Alternating Lower Limb Propulsion With Both Legs.

    Science.gov (United States)

    Murata, Tomoyuki; Asami, Toyoko; Matsuo, Kiyomi; Kubo, Atsuko; Okigawa, Etsumi

    2014-01-01

    This study investigated the effects of seat-height settings of wheelchairs with alternating propulsion with both legs. Seven healthy individuals with no orthopedic disease participated. Flexion angles at initial contact (FA-IC) of each joint, range of motion during propulsion period (ROM-PP), and ground reaction force (GRF) were measured using a three dimensional motion capture system and force plates, and compared with different seat-height settings. Statistically significant relationships were found between seat-height and speed, stride length, knee FA-IC, ankle FA-IC, hip ROM-PP, vertical ground reaction force (VGRF), and anterior posterior ground reaction force (APGRF). Speed, hip ROM-PP, VGRF and APGRF increased as the seat-height was lowered. This effect diminished when the seat-height was set below -40 mm. VGRF increased as the seat-height was lowered. The results suggest that the seat-height effect can be attributed to hip ROM-PP; therefore, optimal foot propulsion cannot be achieved when the seat height is set either too high or too low. Efficient foot propulsion of the wheelchair can be achieved by setting the seat height to lower leg length according to a combination of physical characteristics, such as the user's physical functions, leg muscles, and range of motion.

  14. Development of methods for inferring cloud thickness and cloud-base height from satellite radiance data

    Science.gov (United States)

    Smith, William L., Jr.; Minnis, Patrick; Alvarez, Joseph M.; Uttal, Taneil; Intrieri, Janet M.; Ackerman, Thomas P.; Clothiaux, Eugene

    1993-01-01

    Cloud-top height is a major factor determining the outgoing longwave flux at the top of the atmosphere. The downwelling radiation from the cloud strongly affects the cooling rate within the atmosphere and the longwave radiation incident at the surface. Thus, determination of cloud-base temperature is important for proper calculation of fluxes below the cloud. Cloud-base altitude is also an important factor in aircraft operations. Cloud-top height or temperature can be derived in a straightforward manner using satellite-based infrared data. Cloud-base temperature, however, is not observable from the satellite, but is related to the height, phase, and optical depth of the cloud in addition to other variables. This study uses surface and satellite data taken during the First ISCCP Regional Experiment (FIRE) Phase-2 Intensive Field Observation (IFO) period (13 Nov. - 7 Dec. 1991, to improve techniques for deriving cloud-base height from conventional satellite data.

  15. Associations between birth size and later height from infancy through adulthood

    DEFF Research Database (Denmark)

    Jelenkovic, Aline; Yokoyama, Yoshie; Sund, Reijo

    2018-01-01

    height was analyzed at both the individual and within-pair level by linear regression analyses. Results: Within twin pairs, regression coefficients showed that a 1-kg increase in birth weight and a 1-cm increase in birth length were associated with 1.14–4.25 cm and 0.18–0.90 cm taller height...

  16. Increase in Jumping Height Associated with Maximal Effort Vertical Depth Jumps.

    Science.gov (United States)

    Bedi, John F.; And Others

    1987-01-01

    In order to assess if there existed a statistically significant increase in jumping performance when dropping from different heights, 32 males, aged 19 to 26, performed a series of maximal effort vertical jumps after dropping from eight heights onto a force plate. Results are analyzed. (Author/MT)

  17. Empirical Guidelines for Use of Irregular Wave Model to Estimate Nearshore Wave Height.

    Science.gov (United States)

    1982-07-01

    height, the easier to use tech- nique presented by McClenan (1975) was employed. The McClenan technique uti- lizes a monogram which was constructed from...the SPM equations and gives the same results. The inputs to the monogram technique are the period, the deep- water wave height, the deepwater wave

  18. BOREAS AFM-6 Boundary Layer Height Data

    Science.gov (United States)

    Wilczak, James; Hall, Forrest G. (Editor); Newcomer, Jeffrey A. (Editor); Smith, David E. (Technical Monitor)

    2000-01-01

    The Boreal Ecosystem-Atmosphere Study (BOREAS) Airborne Fluxes and Meteorology (AFM)-6 team from National Oceanic and Atmospheric Adminsitration/Environment Technology Laboratory (NOAA/ETL) operated a 915-MHz wind/Radio Acoustic Sounding System (RASS) profiler system in the Southern Study Area (SSA) near the Old Jack Pine (OJP) site. This data set provides boundary layer height information over the site. The data were collected from 21 May 1994 to 20 Sep 1994 and are stored in tabular ASCII files. The boundary layer height data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). The data files are available on a CD-ROM (see document number 20010000884).

  19. Towards worldwide height unification using ocean information

    Directory of Open Access Journals (Sweden)

    P. L. Woodworth

    2015-03-01

    Full Text Available This paper describes how we are contributing to worldwide height system unification (WHSU by using ocean models together with sea level (tide gauge and altimeter information, geodetic (GPS and levelling data, and new geoid models based on information from the GRACE and GOCE gravity missions, to understand how mean sea level (MSL varies from place to place along the coast. For the last two centuries, MSL has been used to define datums for national levelling systems. However, there are many problems with this. One consequence of WHSU will be the substitution of conventional datums as a reference for heights with the use of geoid, as the only true "level" or datum. This work is within a number of GOCE-related activities funded by the European Space Agency. The study is focused on the coastlines of North America and Europe where the various datasets are most copious.

  20. Height predicts jealousy differently for men and women

    NARCIS (Netherlands)

    Buunk, Abraham P.; Park, Justin H.; Zurriaga, Rosario; Klavina, Liga; Massar, Karlijn

    Because male height is associated with attractiveness, dominance, and reproductive success, taller men may be less jealous. And because female height has a curvilinear relationship with health and reproductive success (with average-height females having the advantages), female height may have a

  1. Lucas Heights buffer zone: plan of management

    International Nuclear Information System (INIS)

    1986-01-01

    This plan is being used by the Commission as a guide for its management of the Lucas Heights buffer zone, which is essentially a circular area having a 1-6 km radius around the HIFAR reactor. Aspects covered by this plan include past uses, current use, objectives for buffer zone land management, emergency evacuation, resource conservation, archaeology, fire, access, rehabilitation of disturbed areas, resource management and plan implementation

  2. Gravity and Height Variations at Medicina, Italy

    Science.gov (United States)

    Bruni, Sara; Zerbini, Susanna; Errico, Maddalena; Santi, Efisio; Wziontek, Hartmut

    2017-04-01

    Since 1996, at the Medicina station, height and gravity variations are monitored continuously by means of GPS, VLBI and superconducting gravimeter (SG) data. Additionally, absolute gravity observations are performed twice a year and environmental parameters, among others water table levels, are regularly acquired. Levelling between the different monuments at the site area is also carried out repeatedly to constrain local ties in the vertical position. Two GPS systems are located very close to each other, and both are in close proximity to the VLBI antenna. Twenty years of data are now available, which allow investigating both long- and short-period height and gravity signals together with their relevant correlations. Natural land subsidence, which is well known to occur in the area, is a major component of the observed long-term behavior; however, non-linear long-period signatures are also present in the time series. On a shorter time scale, fingerprints of the water table seasonal oscillations can be recognized in the data. The Medicina site is characterized by clayey soil subjected to consolidation effects when the water table lowers during summer periods. The pillar on which the SG is installed is especially affected because of its shallow foundation, causing height decreases in the order of 2.5-3 cm for water table lowering of 2 m. This study presents a comparative analysis of the different data sets with the aim of separating mass and deformation contributions in the SG gravity record.

  3. A global boundary-layer height climatology

    Energy Technology Data Exchange (ETDEWEB)

    Dop, H. van; Krol, M.; Holtslag, B. [Inst. for Marine and Atmospheric Research Utrecht, IMAU, Utrecht (Netherlands)

    1997-10-01

    In principle the ABL (atmospheric boundary layer) height can be retrieved from atmospheric global circulation models since they contain algorithms which determine the intensity of the turbulence as a function of height. However, these data are not routinely available, or on a (vertical) resolution which is too crude in view of the application. This justifies the development of a separate algorithm in order to define the ABL. The algorithm should include the generation of turbulence by both shear and buoyancy and should be based on readily available atmospheric parameters. There is obviously a wide application for boundary heights in off-line global and regional chemistry and transport modelling. It is also a much used parameter in air pollution meteorology. In this article we shall present a theory which is based on current insights in ABL dynamics. The theory is applicable over land and sea surfaces in all seasons. The theory is (for various reasons) not valid in mountainous areas. In areas where boundary-layer clouds or deep cumulus convection are present the theory does not apply. However, the same global atmospheric circulation models contain parameterizations for shallow and deep convection from which separate estimates can be obtained for the extent of vertical mixing. (au)

  4. Modeling of the height control system using artificial neural networks

    Directory of Open Access Journals (Sweden)

    A. R Tahavvor

    2016-09-01

    Full Text Available Introduction Automation of agricultural and machinery construction has generally been enhanced by intelligent control systems due to utility and efficiency rising, ease of use, profitability and upgrading according to market demand. A broad variety of industrial merchandise are now supplied with computerized control systems of earth moving processes to be performed by construction and agriculture field vehicle such as grader, backhoe, tractor and scraper machines. A height control machine which is used in measuring base thickness is consisted of two mechanical and electronic parts. The mechanical part is consisted of conveyor belt, main body, electrical engine and invertors while the electronic part is consisted of ultrasonic, wave transmitter and receiver sensor, electronic board, control set, and microcontroller. The main job of these controlling devices consists of the topographic surveying, cutting and filling of elevated and spotted low area, and these actions fundamentally dependent onthe machine's ability in elevation and thickness measurement and control. In this study, machine was first tested and then some experiments were conducted for data collection. Study of system modeling in artificial neural networks (ANN was done for measuring, controlling the height for bases by input variable input vectors such as sampling time, probe speed, conveyer speed, sound wave speed and speed sensor are finally the maximum and minimum probe output vector on various conditions. The result reveals the capability of this procedure for experimental recognition of sensors' behavior and improvement of field machine control systems. Inspection, calibration and response, diagnosis of the elevation control system in combination with machine function can also be evaluated by some extra development of this system. Materials and Methods Designing and manufacture of the planned apparatus classified in three dissimilar, mechanical and electronic module, courses of

  5. Total belowground carbon flux in subalpine forests is related to leaf area index, soil nitrogen, and tree height

    Science.gov (United States)

    Berryman, Erin Michele; Ryan, Michael G.; Bradford, John B.; Hawbaker, Todd J.; Birdsey, R.

    2016-01-01

    In forests, total belowground carbon (C) flux (TBCF) is a large component of the C budget and represents a critical pathway for delivery of plant C to soil. Reducing uncertainty around regional estimates of forest C cycling may be aided by incorporating knowledge of controls over soil respiration and TBCF. Photosynthesis, and presumably TBCF, declines with advancing tree size and age, and photosynthesis increases yet C partitioning to TBCF decreases in response to high soil fertility. We hypothesized that these causal relationships would result in predictable patterns of TBCF, and partitioning of C to TBCF, with natural variability in leaf area index (LAI), soil nitrogen (N), and tree height in subalpine forests in the Rocky Mountains, USA. Using three consecutive years of soil respiration data collected from 22 0.38-ha locations across three 1-km2 subalpine forested landscapes, we tested three hypotheses: (1) annual soil respiration and TBCF will show a hump-shaped relationship with LAI; (2) variability in TBCF unexplained by LAI will be related to soil nitrogen (N); and (3) partitioning of C to TBCF (relative to woody growth) will decline with increasing soil N and tree height. We found partial support for Hypothesis 1 and full support for Hypotheses 2 and 3. TBCF, but not soil respiration, was explained by LAI and soil N patterns (r2 = 0.49), and the ratio of annual TBCF to TBCF plus aboveground net primary productivity (ANPP) was related to soil N and tree height (r2 = 0.72). Thus, forest C partitioning to TBCF can vary even within the same forest type and region, and approaches that assume a constant fraction of TBCF relative to ANPP may be missing some of this variability. These relationships can aid with estimates of forest soil respiration and TBCF across landscapes, using spatially explicit forest data such as national inventories or remotely sensed data products.

  6. Shoulder height, body mass and shape of proboscideans

    Directory of Open Access Journals (Sweden)

    Asier Larramendi

    2016-08-01

    Full Text Available In recent decades there has been a growing interest in proboscideans’ body size, given that mass is highly correlated with biological functions. Different allometric equations have been proposed in the recent decades to estimate their body masses, based on a large number of living examples. However, the results obtained by these formulae are not accurate because extinct animals often had different body proportions and some were outside the size range of extant samples. Here the body mass of a large number of extinct proboscideans has been calculated by the Graphic Double Integration volumetric method which is based on technical restorations from graphical reconstructions of fossils employing photos, measurements and comparative anatomy of extant forms. The method has been tested on extant elephants with highly accurate results. The reconstructions necessary to apply this method give important information such as body proportions. On the other hand, equations to calculate the skeletal shoulder height have been developed, with a large number of published shoulder heights being recalculated. From the shoulder heights, several equations were created to find out the body mass of a series of extant and extinct species. A few of the largest proboscideans, namely Mammut borsoni and Palaeoloxodon namadicus, were found out to have reached and surpassed the body size of the largest indricotheres. Bearing this in mind, the largest land mammal that ever existed seems to be within the order of Proboscidea, contrary to previous understanding.

  7. Alongshore variability of nourished and natural beaches

    NARCIS (Netherlands)

    De Schipper, M.A.

    2014-01-01

    Alongshore variability in topography (i.e. height differences in bed level along the coast) can exist on both natural and nourished beaches. An important question prior to implementation of a nourishment project is how alongshore variability is going to evolve and, related to this variability, the

  8. Corrections for the effects of significant wave height and attitude on Geosat radar altimeter measurements

    Science.gov (United States)

    Hayne, G. S.; Hancock, D. W., III

    1990-01-01

    Range estimates from a radar altimeter have biases which are a function of the significant wave height (SWH) and the satellite attitude angle (AA). Based on results of prelaunch Geosat modeling and simulation, a correction for SWH and AA was already applied to the sea-surface height estimates from Geosat's production data processing. By fitting a detailed model radar return waveform to Geosat waveform sampler data, it is possible to provide independent estimates of the height bias, the SWH, and the AA. The waveform fitting has been carried out for 10-sec averages of Geosat waveform sampler data over a wide range of SWH and AA values. The results confirm that Geosat sea-surface-height correction is good to well within the original dm-level specification, but that an additional height correction can be made at the level of several cm.

  9. Comparative validation of the radiographic and tomographic measurement of patellar height

    Directory of Open Access Journals (Sweden)

    Marco Antonio Schueda

    2013-09-01

    Full Text Available OBJECTIVE: To evaluate and validate the radiographic measurement of patellar height with computerized tomography scans. METHODS: Measured the patellar height through the lateral radiographic image supported by one foot and sagittal tomographic view of the knee in extension, flexion of 20°, and quadriceps contraction of 40 patients (80 knees, asymptomatic and no history of knee injuries using Insall-Salvati index. There were 20 adult females and 20 adult males. RESULTS: The height patellar index was higher in women of all images taken, in proportion. There was no statistical difference of patellar height index between the radiographics and tomographics images. CONCLUSION: The Insall-Salvati index in females was higher in all cases evaluated. Furthermore, it is possible to measure the patellar height index during tomographic study without distorting the results obtained, using to define the presence of patella alta or patella baja.

  10. SU-E-I-91: Reproducibility in Prescribed Dose in AEC CT Scans Due to Table Height, Patient Size, and Localizer Acquisition Order

    International Nuclear Information System (INIS)

    Winslow, J; Hurwitz, L; Christianson, O; Samei, E

    2014-01-01

    Purpose: In CT scanners, the automatic exposure control (AEC) tube current prescription depends on the acquired prescan localizer image(s). The purpose of this study was to quantify the effect that table height, patient size, and localizer acquisition order may have on the reproducibility in prescribed dose. Methods: Three phantoms were used for this study: the Mercury Phantom (comprises three tapered and four uniform regions of polyethylene 16, 23, 30, and 37 cm in diameter), acrylic sheets, and an adult anthropomorphic phantom. Phantoms were positioned per clinical protocol by our chief CT technologist or broader symmetry. Using a GE Discovery CT750HD scanner, a lateral (LAT) and posterior-anterior (PA) localizer was acquired for each phantom at different table heights. AEC scan acquisitions were prescribed for each combination of phantom, localizer orientation, and table height; the displayed volume CTDI was recorded for each. Results were analyzed versus table height. Results: For the two largest Mercury Phantom section scans based on the PA localizer, the percent change in volume CTDI from ideal were at least 20% lower and 35% greater for table heights 4 cm above and 4 cm below proper centering, respectively. For scans based on the LAT localizer, the percent change in volume CTDI from ideal were no greater than 12% different for 4 cm differences in table height. The properly centered PA and LAT localizer-based volume CTDI values were within 13% of each other. Conclusion: Since uncertainty in vertical patient positioning is inherently greater than lateral positioning and because the variability in dose exceeds any dose penalties incurred, the LAT localizer should be used to precisely and reproducibly deliver the intended amount of radiation prescribed by CT protocols. CT protocols can be adjusted to minimize the expected change in average patient dose

  11. Behavioral Variables Associated with Obesity in Police Officers

    Science.gov (United States)

    CAN, S. Hakan; HENDY, Helen M.

    2014-01-01

    Past research has documented that non-behavioral variables (such as long work hours, exposure to police stressors) are associated with obesity risk in police officers, but limited research has examined behavioral variables that might be targeted by Employee Assistance Programs for police weight management. The present study compared non-obese and obese officers for behavioral variables found associated with obesity in other adult samples: physical activity (cardiovascular, strength-training, stretching), sleep duration, and consumption of alcohol, fruit and vegetables, and snack foods. Participants included 172 male police officers who completed questionnaires to report height and weight, used to calculate body mass index (BMI = kg/m2) and to divide them into “non-obese” and “obese” groups. They also reported the above behaviors and six non-behavioral variables found associated with obesity risk: age, health problems, family support, police work hours, police stressors, police support. ANCOVAs compared each behavioral variable across obesity status (non-obese, obese), with the six non-behavioral variables used as covariates. Results revealed that cardiovascular and strength-training physical activity were the only behavioral variables that differed significantly between non-obese and obese police officers. The use of self-reported height and weight values may provide Employee Assistance Program with improved cost, time, and officer participation. PMID:24694574

  12. Radiation Doses to Members of the U.S. Population from Ubiquitous Radionuclides in the Body: Part 3, Results, Variability, and Uncertainty

    International Nuclear Information System (INIS)

    Watson, David J.; Strom, Daniel J.

    2011-01-01

    This paper is part three of a three-part series investigating annual effective doses to residents of the United States from intakes of ubiquitous radionuclides, including radionuclides occurring naturally, radionuclides whose concentrations are technologically enhanced, and anthropogenic radionuclides. The radionuclides of interest are the 238 U series (14 nuclides), the actinium series (headed by 235 U; 11 nuclides), and the 232 Th series (11 nuclides); primordial radionuclides 87 Rb and 40 K; cosmogenic and fallout radionuclides 14 C and 3 H; and purely anthropogenic radionuclides 137 Cs- 137m Ba, 129 I and 90 Sr- 90 Y. This series of papers explicitly excludes intakes from inhaling 222 Rn, 220 Rn, and their short-lived decay products; it also excludes intakes of radionuclides in occupational and medical settings. Part one reviewed, summarized, characterized, and grouped all published and some unpublished data for U.S. residents on ubiquitous radionuclide concentrations in tissues and organs. Part two described the methods used to organize the data collected in part one and segregate it into the ages and genders defined by the study, imputed missing values from the existing data, apportioned activity in bone, and imputed activity in hollow organ contents and the remainder of the body. This paper estimates equivalent doses to target tissues from source regions and maps target tissues to lists of tissues with International Commission on Radiation Protection (ICRP) tissue-weighting factors or to surrogate tissue regions when there is no direct match. Effective doses, using ICRP tissue-weighting factors recommended in 1977, 1990, and 2007, are then calculated, and an upper bound of variability of the effective dose is estimated by calculating the average coefficients of variation (CV), assuming all variance is due to variability. Most of the data were for adult males, whose average annual effective dose is estimated to be 337 (micro)Sv y -1 (CV = 0.65, geometric mean

  13. Capim-braquiária sob lotação contínua e com altura única ou variável durante as estações do ano: dinâmica do perfilhamento Signalgrass under continuous stocking with fixed or variable height during the seasons: tillering dynamics

    Directory of Open Access Journals (Sweden)

    Manoel Eduardo Rozalino Santos

    2011-11-01

    Full Text Available Objetivou-se estabelecer estratégias de manejo do pastejo, sob lotação contínua, que otimizem o padrão natural de perfilhamento da Brachiaria decumbens cv. Basilisk. Duas estratégias de manejo do pastejo foram estudadas: em uma, o pasto foi mantido com 25 cm de altura média durante todo o período experimental; e na outra foi mantido em 15 cm de altura média durante o inverno, com aumento para 25 cm a partir do início da primavera. Adotou-se o esquema de parcelas subdivididas em delineamento em blocos casualizados com quatro repetições. Consideraram-se como fator primário as estratégias de manejo do pastejo, caracterizadas pelas alturas médias em que os pastos foram mantidos durante as estações do ano (inverno, primavera e verão e, como fator secundário, as medidas ao longo do período experimental. A taxa de aparecimento de perfilho (4,7%, a taxa de mortalidade (4,7% e o índice de estabilidade (0,998 foram menores no inverno. Nesta estação, contudo, a taxa de sobrevivência de perfilho foi maior (95,3%. Em comparação aos pastos mantidos com 25 cm, aqueles manejados com 15 cm de altura média no inverno apresentaram maiores taxas de aparecimento de perfilho (34,2% e índice de estabilidade (1,065. O florescimento do capim-braquiária ocorreu apenas no verão e com pouca intensidade (0,5%. A otimização da renovação de perfilhos no pasto de B. decumbens cv. Basilisk sob lotação contínua ocorre com seu rebaixamento para 15 cm no início do inverno e seu posterior aumento para 25 cm no início da primavera.The experiment was conducted to establish management strategies of grazing under continuous stocking that optimize the natural pattern of tillering of Brachiaria decumbens cv. Basilisk. Two strategies of grazing management were studied: in one, the grass was maintained with 25-cm mean height throughout the experimental period, and in the other, 15-cm mean height during the winter, rising to 25 cm from beginning of

  14. Comparative analysis between identified injuries of victims of fall from height and other mechanisms of closed trauma

    Directory of Open Access Journals (Sweden)

    José Gustavo Parreira

    Full Text Available OBJECTIVE: To analyze the lesions diagnosed in victims of falls, comparing them with those diagnosed in other mechanisms of blunt trauma.METHODS: We conducted a retrospective study of trauma protocol charts (prospectively collected from 2008 to 2010, including victims of trauma over 13 years of age admitted to the emergency room. The severity of injuries was stratified by the Abbreviated Injury Scale (AIS and Injury Severity Score (ISS. Variables were compared between the group of victims of falls from height (Group 1 and the other victims of blunt trauma (Group 2. We used the Student t, chi-square and Fisher tests for comparison between groups, considering the value of p <0.05 as significant.RESULTS: The series comprised 4,532 cases of blunt trauma, of which 555 (12.2% were victims of falls from height. Severe lesions (AISe"3 were observed in the extremities (17.5%, in the cephalic segment (8.4%, chest (5.5% and the abdomen (2.9%. Victims of Group 1 had significantly higher mean age, AIS in extremities / pelvis, AIS in the thoracic segment and ISS (p <0.05. The group 1 had significantly (p <0.05 higher incidence of tracheal intubation on admission, pneumothorax, hemothorax, rib fractures, chest drainage, spinal trauma, pelvic fractures, complex pelvic fractures and fractures to the upper limbs.CONCLUSION: Victims of fall from height had greater anatomic injury severity, greater frequency and severity of lesions in the thoracic segment and extremities.

  15. Differences between height- and light-dependent changes in shoot traits in five deciduous tree species.

    Science.gov (United States)

    Osada, Noriyuki; Okabe, Yoshihiko; Hayashi, Daisuke; Katsuyama, Tomonori; Tokuchi, Naoko

    2014-01-01

    The effects of tree height on shoot traits may in some cases differ in magnitude and direction from the effects of light. Nevertheless, general patterns of change in shoot traits in relation to variations in height and light have not so far been revealed. A comprehensive analysis of the differences between the effects of height and light on a range of leaf and shoot traits is important for the scaling of these traits to individual trees. We investigated the biomass allocation and structure of current-year shoots at the top of the crowns of five deciduous tree species in Japan. Height effect was investigated by comparing shoot traits among trees of different heights growing under a high light environment. The effects of light were examined by comparing saplings growing in high- and low-light environments. The effects of light were significant for most traits, while those of height were not significant for some traits. The magnitudes of the effects of light were larger than those of height for most traits related to biomass allocation. There was an extreme difference between the effects of height and light in the direction of change in the length of current-year shoots and in the number of standing leaves. The measures of both parameters increased with the increase in light, but decreased with the increase in tree height. Thus, the effects of height and light on diverse traits at the level of current-year shoots were not always similar. These results suggest that great care must be taken when scaling shoot traits from small trees to tall trees because the effects of height and light can be complex.

  16. Height and seasonal growth pattern of jack pine full-sib families

    Science.gov (United States)

    Don E. Riemenschneider

    1981-01-01

    Total tree height, seasonal shoot elongation, dates of growth initiation and cessation, and mean daily growth rate were measured and analyzed for a population of jack pine full-sib families derived from inter-provenance crosses. Parental provenance had no effect on these variables although this may have been due to small sample size. Progenies differed significantly...

  17. Estimating fog-top height through near-surface micrometeorological measurements

    NARCIS (Netherlands)

    Román-Cascón, Carlos; Yagüe, Carlos; Steeneveld, Gert Jan; Sastre, Mariano; Arrillaga, Jon Ander; Maqueda, Gregorio

    2016-01-01

    Fog-top height (fog thickness) is very useful information for aircraft maneuvers, data assimilation/validation of Numerical Weather Prediction models or nowcasting of fog dissipation. This variable is usually difficult to determine, since the fog-layer top cannot be observed from the surface. In

  18. Adult height, coronary heart disease and stroke : A multi-locus Mendelian randomization meta-analysis

    NARCIS (Netherlands)

    Nüesch, Eveline; Dale, Caroline; Palmer, Tom M.; White, Jon; Keating, Brendan J.; van Iperen, Erik P A; Goel, Anuj; Padmanabhan, Sandosh; Asselbergs, F. W.; Verschuren, W. M.; Wijmenga, C.; Van der Schouw, Y. T.; Onland-Moret, N. C.; Lange, Leslie A.; Hovingh, G. K.; Sivapalaratnam, Suthesh; Morris, Richard W.; Whincup, Peter H.; Wannamethe, Goya S.; Gaunt, Tom R.; Ebrahim, Shah; Steel, Laura; Nair, Nikhil; Reiner, Alexander P.; Kooperberg, Charles; Wilson, James F.; Bolton, Jennifer L.; McLachlan, Stela; Price, Jacqueline F.; Strachan, Mark W J; Robertson, Christine M.; Kleber, Marcus E.; Delgado, Graciela; März, Winfried; Melander, Olle; Dominiczak, Anna F.; Farrall, Martin; Watkins, Hugh; Leusink, Maarten; Maitland-van der Zee, Anke H.; de Groot, Mark C H; Dudbridge, Frank; Hingorani, Aroon; Ben-Shlomo, Yoav; Lawlor, Debbie A.; Amuzu, A.; Caufield, M.; Cavadino, A.; Cooper, J.; Davies, T. L.; Day, I. N.; Drenos, F.; Engmann, J.; Finan, C.; Giambartolomei, C.; Hardy, R.; Humphries, S. E.; Hypponen, E.; Kivimaki, M.; Kuh, D.; Kumari, M.; Ong, K.; Plagnol, V.; Power, C.; Richards, M.; Shah, S.; Shah, T.; Sofat, R.; Talmud, P. J.; Wareham, N.; Warren, H.; Whittaker, J. C.; Wong, A.; Zabaneh, D.; Smith, George Davey; Wells, Jonathan C.; Leon, David A.; Holmes, Michael V.; Casas, Juan P.

    2016-01-01

    Background: We investigated causal effect of completed growth, measured by adult height, on coronary heart disease (CHD), stroke and cardiovascular traits, using instrumental variable (IV) Mendelian randomization meta-analysis. Methods: We developed an allele score based on 69 single nucleotide

  19. Auto-correlation analysis of wave heights in the Bay of Bengal

    Indian Academy of Sciences (India)

    Time series observations of significant wave heights in the Bay of Bengal were subjected to auto- correlation analysis to determine temporal variability scale. The analysis indicates an exponen- tial fall of auto-correlation in the first few hours with a decorrelation time scale of about six hours. A similar figure was found earlier ...

  20. Using eddy geopotential height to measure the western North Pacific subtropical high in a warming climate

    Science.gov (United States)

    He, Chao; Lin, Ailan; Gu, Dejun; Li, Chunhui; Zheng, Bin; Wu, Bo; Zhou, Tianjun

    2018-01-01

    The western North Pacific subtropical high (WNPSH) is crucial to the East Asian summer climate, and geopotential height ( H) is widely used to measure the WPNSH. However, a rapidly rising trend of H in the future is projected by the models from the Coupled Model Intercomparison Project Phase 5 (CMIP5). Diagnoses based on the hypsometric equation suggest that more than 80% of the rise in H are attributable to zonal uniform warming. Because circulation is determined by the gradient of H rather than its absolute magnitude, the spatially uniform rising trend of H gives rise to difficulties when measuring the WNPSH with H. These difficulties include an invalid western boundary of WNPSH in the future and spurious information regarding long-term trends and interannual variability of WNPSH. Using CMIP5 model simulations and reanalysis data, the applicability of a metric based on eddy geopotential height ( H e ) to the warming climate is investigated. The results show that the H e metric outperforms the H metric under warming climate conditions. First, the mean state rainfall- H e relationship is more robust than the rainfall- H relationship. Second, the area, intensity, and western boundary indices of WNPSH can be effectively defined by the H e = 0-m contour in future warming climate scenarios without spurious trends. Third, the interannual variability of East Asian summer rainfall is more closely related to the H e -based WNPSH indices. We recommend that the H e metric be adopted as an operational metric on the WNPSH under the current warming climate.

  1. Optimally combined regional geoid models for the realization of height systems in developing countries - ORG4heights

    Science.gov (United States)

    Lieb, Verena; Schmidt, Michael; Willberg, Martin; Pail, Roland

    2017-04-01

    Precise height systems require high-resolution and high-quality gravity data. However, such data sets are sparse especially in developing or newly industrializing countries. Thus, we initiated the DFG-project "ORG4heights" for the formulation of a general scientific concept how to (1) optimally combine all available data sets and (2) estimate realistic errors. The resulting regional gravity field models then deliver the fundamental basis for (3) establishing physical national height systems. The innovative key aspects of the project incorporate the development of a method which links (low- up to mid-resolution) gravity satellite mission data and (high- down to low-quality) terrestrial data. Hereby, an optimal combination of the data utilizing their highest measure of information including uncertainty quantification and analyzing systematic omission errors is pursued. Regional gravity field modeling via Multi-Resolution Representation (MRR) and Least Squares Collocation (LSC) are studied in detail and compared based on their theoretical fundamentals. From the findings, MRR shall be further developed towards implementing a pyramid algorithm. Within the project, we investigate comprehensive case studies in Saudi Arabia and South America, i. e. regions with varying topography, by means of simulated data with heterogeneous distribution, resolution, quality and altitude. GPS and tide gauge records serve as complementary input or validation data. The resulting products include error propagation, internal and external validation. A generalized concept then is derived in order to establish physical height systems in developing countries. The recommendations may serve as guidelines for sciences and administration. We present the ideas and strategies of the project, which combines methodical development and practical applications with high socio-economic impact.

  2. Significant Wave Height under Hurricane Irma derived from SAR Sentinel-1 Data

    Science.gov (United States)

    Lehner, S.; Pleskachevsky, A.; Soloviev, A.; Fujimura, A.

    2017-12-01

    while making landfall on Cuba and the Florida Keys, where IRMA still hit as a category 3 to 4 hurricane. Results are compared to the WW3 model, which could not be validated over an area under strong and variable wind conditions before. A new theory on hurricane intensification based on Kelvin-Helmholtz instability is discussed and a first comparison to the SAR data is given.

  3. SOME ASPECTS IN HEIGHT MEASUREMENT BY UAV PHOTOGRAMMETRY

    Directory of Open Access Journals (Sweden)

    R. Matsuoka

    2013-08-01

    Full Text Available We conducted an experiment to investigate the feasibility of the deformation measurement of a large-scale solar power plant on reclaimed land by UAV photogrammetry. Two teams engaged in the experiment at first. One, which is called Team-A, carried out orientation of images following the procedure of conventional aerial photogrammetry. The other, which is called Team-C, executed that in the manner of close range photogrammetry. The RMSE in height measurement by Team-A was 121.5 mm, while that by Team-C was 8.7 mm. This paper reports an analysis conducted in order to investigate the cause of the large difference in height measurement accuracy between Team-A and Team-C. In the analysis the third team, which is called Team-S, conducts supplementary orientation by using the images utilized by Team-A in the same manner as Team-C did. The RMSE in height measurement by Team-S is 19.1 mm. Our investigation focuses on the difference of the arrangement of points utilized in the orientation. Team-A selected pass points and tie points on image automatically by Intergraph’s ImageStation Automatic Triangulation (ISAT software, while Team-C and Team-S selected points to be utilized in orientation manually so that selected points are distributed uniformly in the experiment area. From the results of the analysis we conclude that the sets of tie points along a straight line on a plane that were selected automatically by the ISAT would bring the low accuracy in height measurement by Team-A.

  4. Assessment of plant biomass and nitrogen nutrition with plant height in early-to mid-season corn.

    Science.gov (United States)

    Yin, Xinhua; Hayes, Robert M; McClure, M Angela; Savoy, Hubert J

    2012-10-01

    The physiological basis for using non-destructive high-resolution measurements of plant height through plant height sensing to guide variable-rate nitrogen (N) applications on corn (Zea mays L.) during early (six-leaf growth stage, V6) to mid (V12) season is largely unknown. This study was conducted to assess the relationships of plant biomass and leaf N with plant height in early- to mid-season corn under six different N rate treatments. Corn plant biomass was significantly and positively related to plant height under an exponential model when both were measured at V6. This relationship explained 62-78% of the variations in corn biomass production. Leaf N concentration was, in general, significantly and positively related to plant height when both were measured at V6, V8, V10 and V12. This relationship became stronger as the growing season progressed from V6 to V12. The relationship of leaf N with plant height in early- to mid-season corn was affected by initial soil N fertility and abnormal weather conditions. The relationship of leaf N concentration with plant height may provide a physiological basis for using plant height sensing to guide variable-rate N applications on corn. Copyright © 2012 Society of Chemical Industry.

  5. Determining Aerosol Plume Height from Two GEO Imagers: Lessons from MISR and GOES

    Science.gov (United States)

    Wu, Dong L.

    2012-01-01

    Aerosol plume height is a key parameter to determine impacts of particulate matters generated from biomass burning, wind-blowing dust, and volcano eruption. Retrieving cloud top height from stereo imageries from two GOES (Geostationary Operational Environmental Satellites) have been demonstrated since 1970's and the principle should work for aerosol plumes if they are optically thick. The stereo technique has also been used by MISR (Multiangle Imaging SpectroRadiometer) since 2000 that has nine look angles along track to provide aerosol height measurements. Knowing the height of volcano aerosol layers is as important as tracking the ash plume flow for aviation safety. Lack of knowledge about ash plume height during the 2010 Eyja'rjallajokull eruption resulted in the largest air-traffic shutdown in Europe since World War II. We will discuss potential applications of Asian GEO satellites to make stereo measurements for dust and volcano plumes.

  6. Body height affects the strength of immune response in young men, but not young women.

    Science.gov (United States)

    Krams, Indrikis A; Skrinda, Ilona; Kecko, Sanita; Moore, Fhionna R; Krama, Tatjana; Kaasik, Ants; Meija, Laila; Lietuvietis, Vilnis; Rantala, Markus J

    2014-08-28

    Body height and other body attributes of humans may be associated with a diverse range of social outcomes such as attractiveness to potential mates. Despite evidence that each parameter plays a role in mate choice, we have little understanding of the relative role of each, and relationships between indices of physical appearance and general health. In this study we tested relationships between immune function and body height of young men and women. In men, we report a non-linear relationship between antibody response to a hepatitis-B vaccine and body height, with a positive relationship up to a height of 185 cm, but an inverse relationship in taller men. We did not find any significant relationship between body height and immune function in women. Our results demonstrate the potential of vaccination research to reveal costly traits that govern evolution of mate choice in humans and the importance of trade-offs among these traits.

  7. Does Height to Width Ratio Correlate with Mean Volume in Gastropods?

    Science.gov (United States)

    Barriga, R.; Seixas, G.; Payne, J.

    2012-12-01

    Marine organisms' shell shape and size show important biological information. For example, shape and size can dictate how the organism ranges for food and escapes predation. Due to lack of data and analysis, the evolution of shell size in marine gastropods (snails) remains poorly known. In this study, I attempt to find the relationship between height to width ratio and mean volume. I collected height and width measurements from primary literature sources and calculated volume from these measurements. My results indicate that there was no correlation between height to width ratio and mean volume between 500 to 200 Ma, but there was a correlation between 200 Ma to present where there is a steady increase in both height to width ratio and mean volume. This means that shell shape was not an important factor at the beginning of gastropod evolution but after 200 Ma body size evolution was increasingly driven by the height to width ratio.

  8. 3D Participatory Sensing with Low-Cost Mobile Devices for Crop Height Assessment--A Comparison with Terrestrial Laser Scanning Data.

    Directory of Open Access Journals (Sweden)

    Sabrina Marx

    Full Text Available The integration of local agricultural knowledge deepens the understanding of complex phenomena such as the association between climate variability, crop yields and undernutrition. Participatory Sensing (PS is a concept which enables laymen to easily gather geodata with standard low-cost mobile devices, offering new and efficient opportunities for agricultural monitoring. This study presents a methodological approach for crop height assessment based on PS. In-field crop height variations of a maize field in Heidelberg, Germany, are gathered with smartphones and handheld GPS devices by 19 participants. The comparison of crop height values measured by the participants to reference data based on terrestrial laser scanning (TLS results in R2 = 0.63 for the handheld GPS devices and R2 = 0.24 for the smartphone-based approach. RMSE for the comparison between crop height models (CHM derived from PS and TLS data is 10.45 cm (GPS devices and 14.69 cm (smartphones. Furthermore, the results indicate that incorporating participants' cognitive abilities in the data collection process potentially improves the quality data captured with the PS approach. The proposed PS methods serve as a fundament to collect agricultural parameters on field-level by incorporating local people. Combined with other methods such as remote sensing, PS opens new perspectives to support agricultural development.

  9. 3D Participatory Sensing with Low-Cost Mobile Devices for Crop Height Assessment--A Comparison with Terrestrial Laser Scanning Data.

    Science.gov (United States)

    Marx, Sabrina; Hämmerle, Martin; Klonner, Carolin; Höfle, Bernhard

    2016-01-01

    The integration of local agricultural knowledge deepens the understanding of complex phenomena such as the association between climate variability, crop yields and undernutrition. Participatory Sensing (PS) is a concept which enables laymen to easily gather geodata with standard low-cost mobile devices, offering new and efficient opportunities for agricultural monitoring. This study presents a methodological approach for crop height assessment based on PS. In-field crop height variations of a maize field in Heidelberg, Germany, are gathered with smartphones and handheld GPS devices by 19 participants. The comparison of crop height values measured by the participants to reference data based on terrestrial laser scanning (TLS) results in R2 = 0.63 for the handheld GPS devices and R2 = 0.24 for the smartphone-based approach. RMSE for the comparison between crop height models (CHM) derived from PS and TLS data is 10.45 cm (GPS devices) and 14.69 cm (smartphones). Furthermore, the results indicate that incorporating participants' cognitive abilities in the data collection process potentially improves the quality data captured with the PS approach. The proposed PS methods serve as a fundament to collect agricultural parameters on field-level by incorporating local people. Combined with other methods such as remote sensing, PS opens new perspectives to support agricultural development.

  10. A Correction Equation for Jump Height Measured Using the Just Jump System.

    Science.gov (United States)

    McMahon, John J; Jones, Paul A; Comfort, Paul

    2016-05-01

    To determine the concurrent validity and reliability of the popular Just Jump system (JJS) for determining jump height and, if necessary, provide a correction equation for future reference. Eighteen male college athletes performed 3 bilateral countermovement jumps (CMJs) on 2 JJSs (alternative method) that were placed on top of a force platform (criterion method). Two JJSs were used to establish consistency between systems. Jump height was calculated from flight time obtained from the JJS and force platform. Intraclass correlation coefficients (ICCs) demonstrated excellent within-session reliability of the CMJ height measurement derived from both the JJS (ICC = .96, P jump height (0.46 ± 0.09 m vs 0.33 ± 0.08 m) than the force platform (P jump height = (0.8747 × alternative jump height) - 0.0666. The JJS provides a reliable but overestimated measure of jump height. It is suggested, therefore, that practitioners who use the JJS as part of future work apply the correction equation presented in this study to resultant jump-height values.

  11. Influence of contact height on the performance of vertically aligned carbon nanotube field-effect transistors

    KAUST Repository

    Li, Jingqi; Cheng, Yingchun; Guo, Zaibing; Wang, Zhihong; Zhu, Zhiyong; Zhang, Qing; Chan-Park, Chanpark; Schwingenschlö gl, Udo; Zhang, Xixiang

    2013-01-01

    Vertically aligned carbon nanotube field-effect transistors (CNTFETs) have been experimentally demonstrated (J. Li et al., Carbon, 2012, 50, 4628-4632). The source and drain contact heights in vertical CNTFETs could be much higher than in flat CNTFETs if the fabrication process is not optimized. To understand the impact of contact height on transistor performance, we use a semi-classical method to calculate the characteristics of CNTFETs with different contact heights. The results show that the drain current decreases with increasing contact height and saturates at a value governed by the thickness of the oxide. The current reduction caused by the increased contact height becomes more significant when the gate oxide is thicker. The higher the drain voltage, the larger the current reduction. It becomes even worse when the band gap of the carbon nanotube is larger. The current can differ by a factor of more than five between the CNTEFTs with low and high contact heights when the oxide thickness is 50 nm. In addition, the influence of the contact height is limited by the channel length. The contact height plays a minor role when the channel length is less than 100 nm. © 2013 The Royal Society of Chemistry.

  12. Modification and application of TOUGH2 as a variable-density, saturated-flow code and comparison to SWIFT II results

    International Nuclear Information System (INIS)

    Christian-Frear, T.L.; Webb, S.W.

    1995-01-01

    Human intrusion scenarios at the Waste Isolation Pilot Plant (WIPP) involve penetration of the repository and an underlying brine reservoir by a future borehole. Brine and gas from the brine reservoir and the repository may flow up the borehole and into the overlying Culebra formation, which is saturated with water containing different amounts of dissolved 'solids resulting in a spatially varying density. Current modeling approaches involve perturbing a steady-state Culebra flow field by inflow of gas and/or brine from a breach borehole that has passed through the repository. Previous studies simulating steady-state flow in the Culebra have been done. One specific study by LaVenue et al. (1990) used the SWIFT 2 code, a single-phase flow and transport code, to develop the steady-state flow field. Because gas may also be present in the fluids from the intrusion borehole, a two-phase code such as TOUGH2 can be used to determine the effect that emitted fluids may have on the steady-state Culebra flow field. Thus a comparison between TOUGH2 and SWIFT2 was prompted. In order to compare the two codes and to evaluate the influence of gas on flow in the Culebra, modifications were made to TOUGH2. Modifications were performed by the authors to allow for element-specific values of permeability, porosity, and elevation. The analysis also used a new equation of state module for a water-brine-air mixture, EOS7 (Pruess, 1991), which was developed to simulate variable water densities by assuming a miscible mixture of water and brine phases and allows for element-specific brine concentration in the INCON file

  13. Fluid selection and parametric analysis on condensation temperature and plant height for a thermogravimetric heat pump

    International Nuclear Information System (INIS)

    Najafi, Behzad; Obando Vega, Pedro; Guilizzoni, Manfredo; Rinaldi, Fabio; Arosio, Sergio

    2015-01-01

    The Thermogravimetric Heat Pump (TGHP) is a non-conventional system, implementing a reverse cycle, the main difference of which from the usual vapor compression (Rankine) cycle is a quasi-isothermal compression of the working fluid by a high heat capacity carrier fluid. Previous studies showed that employing HFC134a or PF5050 as working fluids may be promising in terms of thermodynamic performance, though the corresponding required plant heights confine its application to tall buildings (from minimum height of 10–12 storeys to skyscrapers). Accordingly, an investigation has been carried out in the present study in order to determine a group of fluids which allow lower heights under the same input conditions. In order to investigate the performance of the system and the required plant height, operation of a 100 kW TGHP has been simulated for 17 different fluids. Accordingly, the corresponding COPs and required heights are determined and based on the achieved COPs, the optimum fluid for each range of building height is selected. The resulting plant heights range from 20 m to nearly 200 m and R245ca is shown to be the most promising fluid for the lowest plant height range. A parametric study is next carried out in order to study the effect of variations in the condensation temperature and the dimensionless plant height on the performance of the system. The obtained results demonstrate that an increase in the former from 313 K to 348 K, for almost all of the analyzed fluids, causes a reduction of around 50% in the COP. It is also shown that, almost independent of the employed fluid, the maximum values of COP are reached for a dimensionless plant height of around 1.8. Moreover, all the analyzed fluids show basically the same COP trend and, at the same operating conditions, the COP values for all fluids are within a 10% range of variation. This leads to the conclusion that the thermophysical properties of the employed fluid mainly influences the required height of

  14. Occurrence and temporal variability of methyl tert-butyl ether (MTBE) and other volatile organic compounds in select sources of drinking water : results of the focused survey

    Science.gov (United States)

    Delzer, Gregory C.; Ivahnenko, Tamara

    2003-01-01

    The large-scale use of the gasoline oxygenate methyl tert-butyl ether (MTBE), and its high solubility, low soil adsorption, and low biodegradability, has resulted in its detection in ground water and surface water in many places throughout the United States. Studies by numerous researchers, as well as many State and local environmental agencies, have discovered high levels of MTBE in soils and ground water at leaking underground gasoline-storage-tank sites and frequent occurrence of low to intermediate levels of MTBE in reservoirs used for both public water supply and recreational boating.In response to these findings, the American Water Works Association Research Foundation sponsored an investigation of MTBE and other volatile organic compounds (VOCs) in the Nation's sources of drinking water. The goal of the investigation was to provide additional information on the frequency of occurrence, concentration, and temporal variability of MTBE and other VOCs in source water used by community water systems (CWSs). The investigation was completed in two stages: (1) reviews of available literature and (2) the collection of new data. Two surveys were associated with the collection of new data. The first, termed the Random Survey, employed a statistically stratified design for sampling source water from 954 randomly selected CWSs. The second, which is the focus of this report, is termed the Focused Survey, which included samples collected from 134 CWS source waters, including ground water, reservoirs, lakes, rivers, and streams, that were suspected or known to contain MTBE. The general intent of the Focused Survey was to compare results with the Random Survey and provide an improved understanding of the occurrence, concentration, temporal variability, and anthropogenic factors associated with frequently detected VOCs. Each sample collected was analyzed for 66 VOCs, including MTBE and three other ether gasoline oxygenates (hereafter termed gasoline oxygenates). As part of

  15. New Variable Stars Discovered by Data Mining Images Taken during Recent Asteroid Photometric Observations. II. Results from July 2015 through December 2016

    Science.gov (United States)

    Papini, R.; Marchini, A.; Salvaggio, F.; Agnetti, D.; Bacci, P.; Banfi, M.; Bianciardi, G.; Collina, M.; Franco, L.; Galli, G.; Milani, M. G. A.; Lopresti, C.; Marino, G.; Rizzuti, L.; Ruocco, N.; Quadri, U.

    2017-12-01

    This paper follows the previous publication of new variables discovered at Astronomical Observatory, DSFTA, University of Siena, while observing asteroids in order to determine their rotational periods. Usually, this task requires time series images acquisition on a single field for as long as possible on a few nights not necessarily consecutive. Checking continually this "goldmine" allowed us to discover 57 variable stars not yet listed in catalogues or databases. While most of the new variables are eclipsing binaries, a few belong to the RR Lyrae or delta Scuti class. Since asteroid work is definitely a time-consuming activity, coordinated campaigns of follow-up with other observatories have been fundamental in order to determine the elements of the ephemeris and sometimes the right subclass of variability. Further observations of these new variables are therefore strongly encouraged in order to better characterize these stars, especially pulsating ones whose data combined with those taken during professional surveys seem to suggest the presence of light curve amplitude and period variations.

  16. Environmental survey at Lucas Heights Research Laboratories, 1984

    International Nuclear Information System (INIS)

    Giles, M.S.; Dudaitis, A.

    1986-12-01

    Results are presented of the environmental survey conducted in the neighbourhood of the Lucas Heights Research Laboratories during 1984. These results are satisfactory. No radioactivity which could have originated from these laboratories was found in samples collected from possible human food chains. All low-level liquid and gaseous waste discharges were within authorised limits. The maximum possible annual dose to the general public from airborne waste discharges during this period is estimated to be less than 0.01 millisieverts, which is one per cent of the limit for long-term exposure that is recommended by the National Health and Medical Research Council

  17. Environmental survey at the Lucas Heights Research Laboratories. 1983

    International Nuclear Information System (INIS)

    Giles, M.S.; Dudaitis, A.

    1985-12-01

    Results are presented of the environmental survey conducted in the neighbourhood of the Lucas Heights Research Laboratories during 1983. These results are satisfactory. No radioactivity which could have originated from these laboratories was found in samples collected from possible human food chains. All low-level liquid and gaseous waste discharges were within authorised limits. The maximum possible annual dose to the general public from airborne waste discharges during this period is estimated to be less than 0.01 millisieverts, which is 1 per cent of the limit for long-term exposure that is recommended by the National Health and Medical Research Council

  18. Effect of weight, height and BMI on injury outcome in side impact crashes without airbag deployment.

    Science.gov (United States)

    Pal, Chinmoy; Tomosaburo, Okabe; Vimalathithan, K; Jeyabharath, M; Muthukumar, M; Satheesh, N; Narahari, S

    2014-11-01

    A comprehensive analysis is performed to evaluate the effect of weight, height and body mass index (BMI) of occupants on side impact injuries at different body regions. The accident dataset for this study is based on the National Automotive Sampling System-Crashworthiness Data System (NASS-CDS) for accident year 2000-08. The mean BMI values for driver and front passenger are estimated from all types of crashes using NASS database, which clearly indicates that mean BMI has been increasing over the years in the USA. To study the effect of BMI in side impact injuries, BMI was split into three groups namely (1) thin (BMI30). For more clear identification of the effect of BMI in side impact injuries, a minimum gap of three BMI is set in between each adjacent BMI groups. Car model years from MY1995-1999 to MY2000-2008 are chosen in order to identify the degree of influence of older and newer generation of cars in side impact injuries. Impact locations particularly side-front (F), side-center (P) and side-distributed (Y) are chosen for this analysis. Direction of force (DOF) considered for both near side and far side occupants are 8 o'clock, 9 o'clock, 10 o'clock and 2 o'clock, 3 o'clock and 4 o'clock respectively. Age <60 years is also one of the constraints imposed on data selection to minimize the effect of bone strength on the occurrence of occupant injuries. AIS2+ and AIS3+ injury risk in all body regions have been plotted for the selected three BMI groups of occupant, delta-V 0-60kmph, two sets (old and new) of car model years. The analysis is carried with three approaches: (a) injury risk percentage based on simple graphical method with respect to a single variable, (b) injury distribution method where the injuries are marked on the respective anatomical locations and (c) logistic regression, a statistical method, considers all the related variables together. Lower extremity injury risk appears to be high for thin BMI group. It is found that BMI does not have much

  19. Standing Height and its Estimation Utilizing Foot Length Measurements in Adolescents from Western Region in Kosovo

    Directory of Open Access Journals (Sweden)

    Stevo Popović

    2017-10-01

    Full Text Available The purpose of this research is to examine standing height in both Kosovan genders in the Western Region as well as its association with foot length, as an alternative to estimating standing height. A total of 664 individuals (338 male and 326 female participated in this research. The anthropometric measurements were taken according to the protocol of ISAK. The relationships between body height and foot length were determined using simple correlation coefficients at a ninety-five percent confidence interval. A comparison of means of standing height and foot length between genders was performed using a t-test. After that a linear regression analysis were carried out to examine extent to which foot length can reliably predict standing height. Results displayed that Western Kosovan male are 179.71±6.00cm tall and have a foot length of 26.73±1.20cm, while Western Kosovan female are 166.26±5.23cm tall and have a foot length of 23.66±1.06cm. The results have shown that both genders made Western-Kosovans a tall group, a little bit taller that general Kosovan population. Moreover, the foot length reliably predicts standing height in both genders; but, not reliably enough as arm span. This study also confirms the necessity for developing separate height models for each region in Kosovo as the results from Western-Kosovans don’t correspond to the general values.

  20. Correlation among body height, intelligence, and brain gray matter volume in healthy children.

    Science.gov (United States)

    Taki, Yasuyuki; Hashizume, Hiroshi; Sassa, Yuko; Takeuchi, Hikaru; Asano, Michiko; Asano, Kohei; Kotozaki, Yuka; Nouchi, Rui; Wu, Kai; Fukuda, Hiroshi; Kawashima, Ryuta

    2012-01-16

    A significant positive correlation between height and intelligence has been demonstrated in children. Additionally, intelligence has been associated with the volume of gray matter in the brains of children. Based on these correlations, we analyzed the correlation among height, full-scale intelligence quotient (IQ) and gray matter volume applying voxel-based morphometry using data from the brain magnetic resonance images of 160 healthy children aged 5-18 years of age. As a result, body height was significantly positively correlated with brain gray matter volume. Additionally, the regional gray matter volume of several regions such as the bilateral prefrontal cortices, temporoparietal region, and cerebellum was significantly positively correlated with body height and that the gray matter volume of several of these regions was also significantly positively correlated with full-scale intelligence quotient (IQ) scores after adjusting for age, sex, and socioeconomic status. Our results demonstrate that gray and white matter volume may mediate the correlation between body height and intelligence in healthy children. Additionally, the correlations among gray and white matter volume, height, and intelligence may be at least partially explained by the effect of insulin-like growth factor-1 and growth hormones. Given the importance of the effect of environmental factors, especially nutrition, on height, IQ, and gray matter volume, the present results stress the importance of nutrition during childhood for the healthy maturation of body and brain. Copyright © 2011 Elsevier Inc. All rights reserved.

  1. Optimization of digital image processing to determine quantum dots' height and density from atomic force microscopy.

    Science.gov (United States)

    Ruiz, J E; Paciornik, S; Pinto, L D; Ptak, F; Pires, M P; Souza, P L

    2018-01-01

    An optimized method of digital image processing to interpret quantum dots' height measurements obtained by atomic force microscopy is presented. The method was developed by combining well-known digital image processing techniques and particle recognition algorithms. The properties of quantum dot structures strongly depend on dots' height, among other features. Determination of their height is sensitive to small variations in their digital image processing parameters, which can generate misleading results. Comparing the results obtained with two image processing techniques - a conventional method and the new method proposed herein - with the data obtained by determining the height of quantum dots one by one within a fixed area, showed that the optimized method leads to more accurate results. Moreover, the log-normal distribution, which is often used to represent natural processes, shows a better fit to the quantum dots' height histogram obtained with the proposed method. Finally, the quantum dots' height obtained were used to calculate the predicted photoluminescence peak energies which were compared with the experimental data. Again, a better match was observed when using the proposed method to evaluate the quantum dots' height. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Inverted Polarity Thunderstorms Linked with Elevated Cloud Base Height

    Science.gov (United States)

    Cummins, K. L.; Williams, E.

    2016-12-01

    The great majority of thunderstorms worldwide exhibit gross positive dipole structure, produce intracloud lightning that reduces this positive dipole (positive intracloud flashes), and produce negative cloud-to-ground lightning from the lower negative end of this dipole. During the STEPS experiment in 2000 much new evidence for thunderstorms (or cells within multi-cellular storms) with inverted polarity came to light, both from balloon soundings of electric field and from LMA analysis. Many of the storms with inverted polarity cells developed in eastern Colorado. Fleenor et al. (2009) followed up after STEPS to document a dominance of positive polarity CG lightning in many of these cases. In the present study, surface thermodynamic observations (temperature and dew point temperature) have been used to estimate the cloud base heights and temperatures at the time of the Fleenor et al. lightning observations. It was found that when more than 90% of the observed CG lightning polarity within a storm is negative, the cloud base heights were low (2000 m AGL or lower, and warmer, with T>10 C), and when more than 90% of the observed CG lightning within a storm was positive, the cloud base heights were high (3000 m AGL or higher, and colder, with Tmixed polarity were generally associated with intermediate cloud base heights. These findings on inverted polarity thunderstorms are remarkably consistent with results in other parts of the world where strong instability prevails in the presence of high cloud base height: the plateau regions of China (Liu et al., 1989; Qie et al., 2005), and in pre-monsoon India (Pawar et al., 2016), particularly when mixed polarity cases are excluded. Calculations of adiabatic cloud water content for lifting from near 0 oC cast some doubt on earlier speculation (Williams et al., 2005) that the graupel particles in these inverted polarity storms attain a wet growth condition, and so exhibit positive charging following laboratory experiments. This

  3. CALIOP-based Biomass Burning Smoke Plume Injection Height

    Science.gov (United States)

    Soja, A. J.; Choi, H. D.; Fairlie, T. D.; Pouliot, G.; Baker, K. R.; Winker, D. M.; Trepte, C. R.; Szykman, J.

    2017-12-01

    Carbon and aerosols are cycled between terrestrial and atmosphere environments during fire events, and these emissions have strong feedbacks to near-field weather, air quality, and longer-term climate systems. Fire severity and burned area are under the control of weather and climate, and fire emissions have the potential to alter numerous land and atmospheric processes that, in turn, feedback to and interact with climate systems (e.g., changes in patterns of precipitation, black/brown carbon deposition on ice/snow, alteration in landscape and atmospheric/cloud albedo). If plume injection height is incorrectly estimated, then the transport and deposition of those emissions will also be incorrect. The heights to which smoke is injected governs short- or long-range transport, which influences surface pollution, cloud interaction (altered albedo), and modifies patterns of precipitation (cloud condensation nuclei). We are working with the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) science team and other stakeholder agencies, primarily the Environmental Protection Agency and regional partners, to generate a biomass burning (BB) plume injection height database using multiple platforms, sensors and models (CALIOP, MODIS, NOAA HMS, Langley Trajectory Model). These data have the capacity to provide enhanced smoke plume injection height parameterization in regional, national and international scientific and air quality models. Statistics that link fire behavior and weather to plume rise are crucial for verifying and enhancing plume rise parameterization in local-, regional- and global-scale models used for air quality, chemical transport and climate. Specifically, we will present: (1) a methodology that links BB injection height and CALIOP air parcels to specific fires; (2) the daily evolution of smoke plumes for specific fires; (3) plumes transport and deposited on the Greenland Ice Sheet; and (4) compare CALIOP-derived smoke plume injection

  4. Sensitivity of Turbine-Height Wind Speeds to Parameters in Planetary Boundary-Layer and Surface-Layer Schemes in the Weather Research and Forecasting Model

    Science.gov (United States)

    Yang, Ben; Qian, Yun; Berg, Larry K.; Ma, Po-Lun; Wharton, Sonia; Bulaevskaya, Vera; Yan, Huiping; Hou, Zhangshuan; Shaw, William J.

    2017-01-01

    We evaluate the sensitivity of simulated turbine-height wind speeds to 26 parameters within the Mellor-Yamada-Nakanishi-Niino (MYNN) planetary boundary-layer scheme and MM5 surface-layer scheme of the Weather Research and Forecasting model over an area of complex terrain. An efficient sampling algorithm and generalized linear model are used to explore the multiple-dimensional parameter space and quantify the parametric sensitivity of simulated turbine-height wind speeds. The results indicate that most of the variability in the ensemble simulations is due to parameters related to the dissipation of turbulent kinetic energy (TKE), Prandtl number, turbulent length scales, surface roughness, and the von Kármán constant. The parameter associated with the TKE dissipation rate is found to be most important, and a larger dissipation rate produces larger hub-height wind speeds. A larger Prandtl number results in smaller nighttime wind speeds. Increasing surface roughness reduces the frequencies of both extremely weak and strong airflows, implying a reduction in the variability of wind speed. All of the above parameters significantly affect the vertical profiles of wind speed and the magnitude of wind shear. The relative contributions of individual parameters are found to be dependent on both the terrain slope and atmospheric stability.

  5. Trend in Height of Turkish and Moroccan Children Living in The Netherlands

    Science.gov (United States)

    Schönbeck, Yvonne; van Dommelen, Paula; HiraSing, Remy A.; van Buuren, Stef

    2015-01-01

    Objectives To study trends in height of Turkish and Moroccan immigrant children living in The Netherlands, to investigate the association between height and background characteristics in these children, and to calculate height-for-age-references data for these groups. Design Nationwide cross-sectional data collection from children aged 0 to 18 years by trained professionals in 1997 and 2009. The study population consisted of 2,822 Turkish 2,779 Moroccan, and 13,705 Dutch origin children in 1997and 2,548 Turkish, 2,594 Moroccan, and 11,255 Dutch origin children in 2009. Main outcome measures: Mean height in cm, and mean height standard deviation scores. Results In 2009, mean height at the age of 18y was similar for Turkish and Moroccan children: 177 cm for boys and 163 cm for girls, which was 2 to 3 cm taller than in 1997. Still, Turkish and Moroccan adolescents were 5.5 cm (boys) to 7 cm (girls) shorter than their Dutch peers. No significant differences were found in mean height standard deviation scores across the educational level of the parents, geographical region, primary language spoken at home, and immigrant generation. Conclusions While the secular height increase in Dutch children came to a halt, the trend in Turkish and Moroccan children living in The Netherlands continued. However, large differences in height between Turkish and Moroccan children and Dutch children remain. We found no association with the background characteristics. We recommend the use of the new growth charts for children of Turkish and Moroccan origin who have a height-for-age below -2SD on the growth chart for Dutch children. PMID:25938671

  6. The field high-amplitude SX Phe variable BL Cam: results from a multisite photometric campaign. II. Evidence of a binary - possibly triple - system

    Czech Academy of Sciences Publication Activity Database

    Fauvaud, S.; Sareyan, J.P.; Ribas, I.; Rodriguez, E.; Lampens, P.; Klingenberg, G.; Farrell, J.A.; Fumagalli, F.; Simonetti, J.H.; Wolf, M.; Santacana, G.; Zhou, A.; Michel, R.; Fox-Machado, L.; Alvarez, M.; Nava-Vega, A.; Lopez-Gonzalez, M.J.; Casanova, V.M.; Aceituno, F.J.; Scheggia, I.; Rives, J.-J.; Hintz, E.G.; Van Cauteren, P.; Helvaci, M.; Yesilyaprak, C.; Graham, K.A.; Král, L.; Kocián, R.; Kučáková, Hana; Fauvaud, M.; Granslo, B.H.; Michelet, J.; Nicholson, M.P.; Vugnon, J.-M.; Kotková, Lenka; Truparova, K.; Ulusoy, G.; Yasarsoy, B.; Avdibegovic, A.; Blazek, M.; Kliner, J.; Zasche, P.; Bartosikova, S.; Vilasek, M.; Trondal, O.; Van Den Abbeel, F.; Behrend, R.; Wuecher, H.

    2010-01-01

    Roč. 515, June (2010), A39/1-A39/7 ISSN 0004-6361 Institutional research plan: CEZ:AV0Z10030501 Keywords : variables stars * BL Camelopardalis * oscillations Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 4.410, year: 2010

  7. Modeling a secular trend by Monte Carlo simulation of height biased migration in a spatial network.

    Science.gov (United States)

    Groth, Detlef

    2017-04-01

    Background: In a recent Monte Carlo simulation, the clustering of body height of Swiss military conscripts within a spatial network with characteristic features of the natural Swiss geography was investigated. In this study I examined the effect of migration of tall individuals into network hubs on the dynamics of body height within the whole spatial network. The aim of this study was to simulate height trends. Material and methods: Three networks were used for modeling, a regular rectangular fishing net like network, a real world example based on the geographic map of Switzerland, and a random network. All networks contained between 144 and 148 districts and between 265-307 road connections. Around 100,000 agents were initially released with average height of 170 cm, and height standard deviation of 6.5 cm. The simulation was started with the a priori assumption that height variation within a district is limited and also depends on height of neighboring districts (community effect on height). In addition to a neighborhood influence factor, which simulates a community effect, body height dependent migration of conscripts between adjacent districts in each Monte Carlo simulation was used to re-calculate next generation body heights. In order to determine the direction of migration for taller individuals, various centrality measures for the evaluation of district importance within the spatial network were applied. Taller individuals were favored to migrate more into network hubs, backward migration using the same number of individuals was random, not biased towards body height. Network hubs were defined by the importance of a district within the spatial network. The importance of a district was evaluated by various centrality measures. In the null model there were no road connections, height information could not be delivered between the districts. Results: Due to the favored migration of tall individuals into network hubs, average body height of the hubs, and later

  8. 7A.01: INCREASED RISK OF MORTALITY IN OBESE PATIENTS WITH HIGH NOCTURNAL BLOOD PRESSURE VARIABILITY. RESULTS FROM THE ABP-INTERNATIONAL STUDY.

    Science.gov (United States)

    Palatini, P; Reboldi, G P; Beilin, L; Casiglia, E; Eguchi, K; Imai, Y; Kario, K; Ohkubo, T; Pierdomenico, S D; Schwartz, J E; Wing, L; Verdecchia, P

    2015-06-01

    The association between obesity and all-cause mortality is controversial and may differ according to subjects' characteristics. Blood pressure variability (BPV) may be increased in obese individuals and thus impair prognosis. The purpose of this study was to evaluate whether the relationship between obesity and mortality is influenced by short-term ambulatory BPV. The analysis was performed in 8724 participants (54% men) aged 51 ± 15 years enrolled in 8 prospective studies in Australia, Italy, Japan, and U.S.A. The predictive power of obesity (BMI >=30 kg/m2) for mortality was evaluated from multivariable Cox models in the subjects stratified by high or low nocturnal BPV (above or below the median). Obese participants (N = 1286) had higher age-and-sex adjusted systolic and diastolic BPV than the non-obese participants (p = 0.002/<0.001). Obese subjects with high systolic or diastolic BPV had higher nocturnal heart rate (p = 0.01/<0.001) than obese subjects with low BPV and were more frequently diabetic (p<0.001) and heavy alcohol drinkers (p < 0.001). During a median follow-up of 6.4 years there were 361 deaths, 4.7% in the obese and 4.0% in the non-obese individuals (P = NS). However, the risk of mortality among the obese subjects greatly differed according to BPV level. In Cox models including age, sex, mean ambulatory BP, smoking, alcohol use, diabetes, cholesterol, creatinine, and nocturnal heart rate, the obese group with high systolic BPV had a doubled risk of mortality compared to the non-obese group (HR,2.0, 95%CI,1.4-2.9, p < 0.001), whereas the risk was not increased in the obese group with low BPV (P = 0.81). Similar results were found for diastolic BPV, with a HR of 1.7 (1.2-2.5, p = 0.002) in the high BPV group and no association at all with mortality (p = 0.87) in the low BPV group. Inclusion of night-time BP dipping in the regressions did not change the strength of the associations. These data show that high

  9. Effects of Stimulants on Height and Weight: A Review of the Literature

    Science.gov (United States)

    Faraone, Stephen V.; Biederman, Joseph; Morley, Christopher P.; Spencer, Thomas J.

    2008-01-01

    The article reviews existing literature on the effects of stimulant medications on the growth of children with attention-deficit/hyperactivity disorder. It concludes that treatment with stimulants in childhood results in moderate growth deficit in height and weight.

  10. Interactive effect of genetic susceptibility with height, body mass index, and hormone replacement therapy on the risk of breast cancer

    Directory of Open Access Journals (Sweden)

    Harlid Sophia

    2012-06-01

    Full Text Available Abstract Background Breast cancer today has many established risk factors, both genetic and environmental, but these risk factors by themselves explain only part of the total cancer incidence. We have investigated potential interactions between certain known genetic and phenotypic risk factors, specifically nine single nucleotide polymorphisms (SNPs and height, body mass index (BMI and hormone replacement therapy (HRT. Methods We analyzed samples from three different study populations: two prospectively followed Swedish cohorts and one Icelandic case–control study. Totally 2884 invasive breast cancer cases and 4508 controls were analysed in the study. Genotypes were determined using Mass spectrometry-Maldi-TOF and phenotypic variables were derived from measurements and/or questionnaires. Odds Ratios and 95% confidence intervals were calculated using unconditional logistic regression with the inclusion of an interaction term in the logistic regression model. Results One SNP (rs851987 in ESR1 tended to interact with height, with an increasingly protective effect of the major allele in taller women (p = 0.007 and rs13281615 (on 8q24 tended to confer risk only in non users of HRT (p-for interaction = 0.03. There were no significant interactions after correction for multiple testing. Conclusions We conclude that much larger sample sets would be necessary to demonstrate interactions between low-risk genetic polymorphisms and the phenotypic variables height, BMI and HRT on the risk for breast cancer. However the present hypothesis-generating study has identified tendencies that would be of interest to evaluate for gene-environment interactions in independent materials.

  11. Influence of micro-topography and crown characteristics on tree height estimations in tropical forests based on LiDAR canopy height models

    Science.gov (United States)

    Alexander, Cici; Korstjens, Amanda H.; Hill, Ross A.

    2018-03-01

    Tree or canopy height is an important attribute for carbon stock estimation, forest management and habitat quality assessment. Airborne Laser Scanning (ALS) based on Light Detection and Ranging (LiDAR) has advantages over other remote sensing techniques for describing the structure of forests. However, sloped terrain can be challenging for accurate estimation of tree locations and heights based on a Canopy Height Model (CHM) generated from ALS data; a CHM is a height-normalised Digital Surface Model (DSM) obtained by subtracting a Digital Terrain Model (DTM) from a DSM. On sloped terrain, points at the same elevation on a tree crown appear to increase in height in the downhill direction, based on the ground elevations at these points. A point will be incorrectly identified as the treetop by individual tree crown (ITC) recognition algorithms if its height is greater than that of the actual treetop in the CHM, which will be recorded as the tree height. In this study, the influence of terrain slope and crown characteristics on the detection of treetops and estimation of tree heights is assessed using ALS data in a tropical forest with complex terrain (i.e. micro-topography) and tree crown characteristics. Locations and heights of 11,442 trees based on a DSM are compared with those based on a CHM. The horizontal (DH) and vertical displacements (DV) increase with terrain slope (r = 0.47 and r = 0.54 respectively, p tree height are up to 16.6 m on slopes greater than 50° in our study area in Sumatra. The errors in locations (DH) and tree heights (DV) are modelled for trees with conical and spherical tree crowns. For a spherical tree crown, DH can be modelled as R sin θ, and DV as R (sec θ - 1). In this study, a model is developed for an idealised conical tree crown, DV = R (tan θ - tan ψ), where R is the crown radius, and θ and ψ are terrain and crown angles respectively. It is shown that errors occur only when terrain angle exceeds the crown angle, with the

  12. Dominant height-based height-diameter equations for trees in southern Indiana

    Science.gov (United States)

    John A., Jr. Kershaw; Robert C. Morrissey; Douglass F. Jacobs; John R. Seifert; James B. McCarter

    2008-01-01

    Height-diameter equations are developed based on dominant tree data collected in 1986 in 8- to 17-year-old clearcuts and the phase 2 Forest Inventory and Analysis plots on the Hoosier National Forest in south central Indiana. Two equation forms are explored: the basic, three-parameter Chapman-Richards function, and a modification of the three-parameter equation...

  13. Apparent Barrier Height in Scanning Tunneling Microscopy Revisited

    DEFF Research Database (Denmark)

    Olesen, L.; Brandbyge, Mads; Sørensen, Mads Reinholdt

    1996-01-01

    The apparent barrier height phi(ap), that is, the rate of change of the logarithm of the conductance with tip-sample separation in a scanning tunneling microscope (STM), has been measured for Ni, Pt, and Au single crystal surfaces. The results show that phi(ap) is constant until point contact...... is reached rather than decreasing at small tunneling gap distances, as previously reported. The findings for phi(ap) can be accounted for theoretically by including the relaxations of the tip-surface junction in an STM due to the strong adhesive forces at close proximity. These relaxation effects are shown...

  14. Environmental survey at Lucas Heights Research Laboratories, 1989

    International Nuclear Information System (INIS)

    Hoffman, E.L.; Arthur, J.

    1990-09-01

    Results are presented of an environmental survey conducted in the neighbourhood of the Lucas Heights Research Laboratories during 1989. No radioactivity which could have originated from these laboratories was found in samples collected from possible human food chains. All low-level liquid and gaseous waste discharges were within authorised limits. The maximum possible annual dose to the general public from airborne waste during this period is estimated to be less than 0.01 millisieverts, which is one per cent of the limit for long-term exposure that is recommended by the National Health and Medical Research Council. 9 refs., 17 tabs., 2 figs

  15. Environmental survey at Lucas Heights Research Laboratories, 1990

    International Nuclear Information System (INIS)

    Hoffmann, E.L.

    1991-10-01

    Results are presented of an environmental survey conducted in the neighbourhood of the Lucas Heights Research Laboratories during 1990. No radioactivity which could have originated from these laboratories was found in samples collected from possible human food chains. All low-level liquid and gaseous waste discharges were within authorised limits. The maximum possible annual dose to the general public from airborne waste during this period is estimated to be less than 0.01 millisieverts, which is one per cent of the limit for long-term exposure that is recommended by the National Health and Medical Research Council. 11 refs., 16 tabs., 2 figs

  16. Environmental survey at Lucas Heights Research Laboratories, 1987

    International Nuclear Information System (INIS)

    Giles, M.S.; Foy, J.J.; Hoffmann, E.L.

    1989-12-01

    Results are presented of an environmental survey conducted in the neighbourhood of the Lucas Heights Research Laboratories during 1987. No radioactivity which could have originated from these laboratories was found in samples collected from possible human food chains. All low-level liquid and gaseous waste discharges were within authorized limits. The maximum possible annual dose to the general public from airborne waste during this period is estimated to be less than 0.01 millisieverts, which is one per cent of the limit for long-term exposure that is recommended by the National Health and Medical Research Council. 9 refs., 18 tabs., 2 figs

  17. Agreement between estimated and measured heights and weights ...

    African Journals Online (AJOL)

    index (BMI = kg/m2) and require accurate recording of a patient's height and weight.1. In reality, however, patients often cannot stand up straight for accurate height measurement, or are unable to step on a scale. In such cases, height and weight values are often obtained from the patient or their relatives, who either do not ...

  18. Anterior Face Height Values in a Nigerian Population | Folaranmi ...

    African Journals Online (AJOL)

    ... Anterior Upper Face Height 47.7 (4) mm, Anterior Total Face Height (ATFH) 108.5 (5) mm, ratio of ALFH to ATFH ALFH: ATFH 56 (4)%. Conclusion: This study provides anterior face height measurements, which will be of great significance in evaluating facial proportions andesthetics in orthodontics, orthognathic surgery, ...

  19. Estimation of Total Tree Height from Renewable Resources Evaluation Data

    Science.gov (United States)

    Charles E. Thomas

    1981-01-01

    Many ecological, biological, and genetic studies use the measurement of total tree height. Until recently, the Southern Forest Experiment Station's inventory procedures through Renewable Resources Evaluation (RRE) have not included total height measurements. This note provides equations to estimate total height based on other RRE measurements.

  20. The Sine Method: An Alternative Height Measurement Technique

    Science.gov (United States)

    Don C. Bragg; Lee E. Frelich; Robert T. Leverett; Will Blozan; Dale J. Luthringer

    2011-01-01

    Height is one of the most important dimensions of trees, but few observers are fully aware of the consequences of the misapplication of conventional height measurement techniques. A new approach, the sine method, can improve height measurement by being less sensitive to the requirements of conventional techniques (similar triangles and the tangent method). We studied...

  1. Practical application of the geometric geoid for heighting over ...

    African Journals Online (AJOL)

    This is because a geoid model is required to convert ellipsoidal heights to orthometric heights that are used in practice. A local geometric geoid ... The geoid height is expressed as a function of the local plane coordinates through a biquadratic surface polynomial, using 14 GPS/levelling points. Five points have been used ...

  2. 14 CFR 27.87 - Height-speed envelope.

    Science.gov (United States)

    2010-01-01

    ... applicable power failure condition in paragraph (b) of this section, a limiting height-speed envelope must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Height-speed envelope. 27.87 Section 27.87... STANDARDS: NORMAL CATEGORY ROTORCRAFT Flight Performance § 27.87 Height-speed envelope. (a) If there is any...

  3. 14 CFR 29.1517 - Limiting height-speed envelope.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Limiting height-speed envelope. 29.1517... Operating Limitations § 29.1517 Limiting height-speed envelope. For Category A rotorcraft, if a range of... following power failure, the range of heights and its variation with forward speed must be established...

  4. 14 CFR 29.87 - Height-velocity envelope.

    Science.gov (United States)

    2010-01-01

    ... Category A engine isolation requirements, the height-velocity envelope for complete power failure must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Height-velocity envelope. 29.87 Section 29... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Flight Performance § 29.87 Height-velocity envelope. (a...

  5. The optical variability of SDSS quasars from multi-epoch spectroscopy. I. Results from 60 quasars with ≥ six-epoch spectra

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Hengxiao; Gu, Minfeng, E-mail: hxguo@shao.ac.cn, E-mail: gumf@shao.ac.cn [Key Laboratory for Research in Galaxies and Cosmology, Shanghai Astronomical Observatory, Chinese Academy of Sciences, 80 Nandan Road, Shanghai 200030 (China)

    2014-09-01

    In a sample of 60 quasars selected from the Sloan Digital Sky Survey with at least six-epoch spectroscopy, we investigate the variability of emission lines and continuum luminosity at various aspects. A strong anti-correlation between the variability and continuum luminosity at 2500 Å is found for the sample, which is consistent with previous works. In individual sources, we find that half of the sample objects follow the trend of being bluer when brighter, while the remaining half follow the redder-when-brighter (RWB) trend. Although the mechanism for RWB is unclear, the effects of host galaxy contribution due to seeing variations cannot be completely ruled out. As expected from the photoionization model, the positive correlations between the broad emission line and continuum luminosity are found in most individual sources, as well as for the whole sample. We confirm the Baldwin effect in most individual objects and the whole sample, while a negative Baldwin effect is also found in several quasars, which can be at least partly (if not all) due to the host galaxy contamination. We find positive correlations between the broad emission line luminosity and line width in most individual quasars, as well as the whole sample, implying a line base that is more variable than the line core.

  6. Peak height velocity as an alternative for maturational classification associated with motor performance

    Directory of Open Access Journals (Sweden)

    Leonardo Trevizan Costa

    2009-01-01

    Full Text Available Adolescence is a phase characterized by important physical and maturational alterations, with individuals of the same chronological age, but who are more mature, may present sportive advantages because of greater force gain and additional muscle mass. Thus, in studies evaluating motor skills of children and adolescents, maturational classification should be an efficient and easily applicable tool in order to facilitate the interpretation of the true relationship between maturation and motor performance. Therefore, the objective of this study was to compare the relationship between motor performance and different types of classification of biological maturation in 209 boys aged to 17 years (11.59 ± 2.57 practicing soccer. Anthropometric variables were obtained according to the ISAK criteria. Biological maturation was determined based on age at peak height velocity (PHV and also by self-assessment of sexual maturation (genitalia and pubic hair. Motor performance was evaluated by sit-and-reach tests, horizontal jump, modified push-ups, 50-m run, and 9/12-min run/walk. The results showed progression in the variables analyzed as the subjects reached maturity. Correlation analysis and the egression values indicated higher consistency for the PHV classification, which better explained motor performance according to maturational status, exceeding the values obtained by comparison according to age or sexual maturation. Thus, the use of PHV as a classification instrument is preferably recommended for youngsters with haracteristics similar to those of the present sample.

  7. Relevance of future snowfall level height in the Peruvian Andes for glacier loss in the 21st century under different emission scenarios

    Science.gov (United States)

    Schauwecker, Simone; Kronenberg, Marlene; Rohrer, Mario; Huggel, Christian; Endries, Jason; Montoya, Nilton; Neukom, Raphael; Perry, Baker; Salzmann, Nadine; Schwarb, Manfred; Suarez, Wilson

    2017-04-01

    In many regions of Peru, the competition for limited hydrological resources already represents a large risk for conflicts. In this context, and within the circumstances of climate change, there is a great interest in estimating the future loss of Peruvian glaciers. Solid precipitation on glaciers, which affects the shortwave radiation budget via its effects on albedo, in general reduces ablation. For that reason, the height of the upper level of the transition zone between liquid and solid precipitation (snowfall level height) is considered to play a critical role. This snowfall level height is linked to air temperature. The observed and projected warming of the atmosphere is therefore affecting the glaciers amongst others by changing the snowfall level height. Despite the potential significance of these changes for Peruvian glaciers, the relations between snowfall level heights, glacier extents and climate scenarios have been poorly investigated so far. In our study, we first analyse the snowfall level heights over the Peruvian Cordilleras. Second, we investigate the relationship between the present snowfall level heights and current glacier extents. As a third step, we derive projected changes of snowfall level heights from GCMs for the RCP2.6 and 8.5 emission scenarios and use them to roughly estimate the end of XXI century glaciation for the Peruvian Cordilleras. Our results indicate a large difference in future glacier extent between the high-emission (pessimistic) RCP8.5 and the low-emission (optimistic) RCP2.6. If global emissions can be substantially reduced, a significant part of the glaciated area of Peru can be maintained. On the contrary, if mitigation is unsuccessful, most of the glacier mass in Peru will be lost during the 21st century. In both cases, but even more so for the high-emission scenario, adaptation will play a critical role and should focus on improvements in water resource management which is essential on a local to regional scale. Air

  8. Urbanization Causes Increased Cloud Base Height and Decreased Fog in Coastal Southern California

    Science.gov (United States)

    Williams, A. Park; Schwartz, Rachel E.; Iacobellis, Sam; Seager, Richard; Cook, Benjamin I.; Still, Christopher J.; Husak, Gregory; Michaelsen, Joel

    2015-01-01

    Subtropical marine stratus clouds regulate coastal and global climate, but future trends in these clouds are uncertain. In coastal Southern California (CSCA), interannual variations in summer stratus cloud occurrence are spatially coherent across 24 airfields and dictated by positive relationships with stability above the marine boundary layer (MBL) and MBL height. Trends, however, have been spatially variable since records began in the mid-1900s due to differences in nighttime warming. Among CSCA airfields, differences in nighttime warming, but not daytime warming, are strongly and positively related to fraction of nearby urban cover, consistent with an urban heat island effect. Nighttime warming raises the near-surface dew point depression, which lifts the altitude of condensation and cloud base height, thereby reducing fog frequency. Continued urban warming, rising cloud base heights, and associated effects on energy and water balance would profoundly impact ecological and human systems in highly populated and ecologically diverse CSCA.

  9. The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

    Directory of Open Access Journals (Sweden)

    Jaime Gomez-Gil

    2014-10-01

    Full Text Available Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations.

  10. Gradient-Based Optimization of Wind Farms with Different Turbine Heights: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Stanley, Andrew P. J.; Thomas, Jared; Ning, Andrew; Annoni, Jennifer; Dykes, Katherine; Fleming, Paul

    2017-05-08

    Turbine wakes reduce power production in a wind farm. Current wind farms are generally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine hub heights. Results indicate that when a farm is optimized for layout and height with two separate height groups, COE can be lowered by as much as 5%-9%, compared to a similar layout and height optimization where all the towers are the same. The COE has the best improvement in farms with high turbine density and a low wind shear exponent.

  11. Gradient-Based Optimization of Wind Farms with Different Turbine Heights

    Energy Technology Data Exchange (ETDEWEB)

    Stanley, Andrew P. J.; Thomas, Jared; Ning, Andrew; Annoni, Jennifer; Dykes, Katherine; Fleming, Paul

    2017-01-09

    Turbine wakes reduce power production in a wind farm. Current wind farms are generally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine hub heights. Results indicate that when a farm is optimized for layout and height with two separate height groups, COE can be lowered by as much as 5%-9%, compared to a similar layout and height optimization where all the towers are the same. The COE has the best improvement in farms with high turbine density and a low wind shear exponent.

  12. Estimating Planetary Boundary Layer Heights from NOAA Profiler Network Wind Profiler Data

    Science.gov (United States)

    Molod, Andrea M.; Salmun, H.; Dempsey, M

    2015-01-01

    An algorithm was developed to estimate planetary boundary layer (PBL) heights from hourly archived wind profiler data from the NOAA Profiler Network (NPN) sites located throughout the central United States. Unlike previous studies, the present algorithm has been applied to a long record of publicly available wind profiler signal backscatter data. Under clear conditions, summertime averaged hourly time series of PBL heights compare well with Richardson-number based estimates at the few NPN stations with hourly temperature measurements. Comparisons with clear sky reanalysis based estimates show that the wind profiler PBL heights are lower by approximately 250-500 m. The geographical distribution of daily maximum PBL heights corresponds well with the expected distribution based on patterns of surface temperature and soil moisture. Wind profiler PBL heights were also estimated under mostly cloudy conditions, and are generally higher than both the Richardson number based and reanalysis PBL heights, resulting in a smaller clear-cloudy condition difference. The algorithm presented here was shown to provide a reliable summertime climatology of daytime hourly PBL heights throughout the central United States.

  13. Effect of plyometric training on vertical jump height in high school basketball players: randomised control trial

    Directory of Open Access Journals (Sweden)

    Chhaya Verma, Lakshmi Subramanium, Vijaya Krishnan

    2015-01-01

    Full Text Available Background: Plyometric involve high intensity eccentric contraction immediately after a powerful concentric contraction. A vertical leap in basketball also involves rapid & repeated muscle contraction & stretching. Various methods have been used to improve the vertical leap in players, but only few studies mention about plyometrics. Aim: To determine the effect of Plyometric training on vertical jump height in high school basketball players & compare them with their untrained counterparts. Methods and Materials: 144 students were randomly selected & distributed in Group I (Pre-pubertal & Group II (Pubertal which was further divided into Group A (trained players & Group B (untrained students. A gender wise distribution followed this. Plyometric training of 6 weeks was conducted & the vertical jump height pre & post training were recorded & compared. Results: Vertical jump height improved significantly post Plyometric in Group Bcompared to Group A. Boys showed improvement in Group B, however girls were better in Group A. Correlation of BMI with vertical jump height was negative & significant in Group B. Conclusion: Plyometric training brought significant change in untrained students. Boys gained more jump height while girls showed significant increase in jump height during pubertal growth spurt. Also, increased BMI reduced jump height.

  14. As tall as my peers - similarity in body height between migrants and hosts.

    Science.gov (United States)

    Bogin, Barry; Hermanussen, Michael; Scheffler, Christiane

    2018-01-12

    Background: We define migrants as people who move from their place of birth to a new place of residence. Migration usually is directed by "Push-Pull" factors, for example to escape from poor living conditions or to find more prosperous socio-economic conditions. Migrant children tend to assimilate quickly, and soon perceive themselves as peers within their new social networks. Differences exist between growth of first generation and second generation migrants. Methods: We review body heights and height distributions of historic and modern migrant populations to test two hypotheses: 1) that migrant and adopted children coming from lower social status localities to higher status localities adjust their height growth toward the mean of the dominant recipient social network, and 2) social dominant colonial and military migrants display growth that significantly surpasses the median height of both the conquered population and the population of origin. Our analytical framework also considered social networks. Recent publications indicate that spatial connectedness (community effects) and social competitiveness can affect human growth. Results: Migrant children and adolescents of lower social status rapidly adjust in height towards average height of their hosts, but tend to mature earlier, and are prone to overweight. The mean height of colonial/military migrants does surpass that of the conquered and origin population. Conclusion: Observations on human social networks, non-human animal strategic growth adjustments, and competitive growth processes strengthen the concept of social connectedness being involved in the regulation of human migrant growth.

  15. Automated lidar-derived canopy height estimates for the Upper Mississippi River System

    Science.gov (United States)

    Hlavacek, Enrika

    2015-01-01

    Land cover/land use (LCU) classifications serve as important decision support products for researchers and land managers. The LCU classifications produced by the U.S. Geological Survey’s Upper Midwest Environmental Sciences Center (UMESC) include canopy height estimates that are assigned through manual aerial photography interpretation techniques. In an effort to improve upon these techniques, this project investigated the use of high-density lidar data for the Upper Mississippi River System to determine canopy height. An ArcGIS tool was developed to automatically derive height modifier information based on the extent of land cover features for forest classes. The measurement of canopy height included a calculation of the average height from lidar point cloud data as well as the inclusion of a local maximum filter to identify individual tree canopies. Results were compared to original manually interpreted height modifiers and to field survey data from U.S. Forest Service Forest Inventory and Analysis plots. This project demonstrated the effectiveness of utilizing lidar data to more efficiently assign height modifier attributes to LCU classifications produced by the UMESC.

  16. An antithetic variate to facilitate upper-stem height measurements for critical height sampling with importance sampling

    Science.gov (United States)

    Thomas B. Lynch; Jeffrey H. Gove

    2013-01-01

    Critical height sampling (CHS) estimates cubic volume per unit area by multiplying the sum of critical heights measured on trees tallied in a horizontal point sample (HPS) by the HPS basal area factor. One of the barriers to practical application of CHS is the fact that trees near the field location of the point-sampling sample point have critical heights that occur...

  17. Adaptive Layer Height During DLP Materials Processing

    DEFF Research Database (Denmark)

    Pedersen, David Bue; Zhang, Yang; Nielsen, Jakob Skov

    2016-01-01

    for considerable process speedup during the Additive Manufacture of components that contain areas of low cross-section variability, at no loss of surface quality. The adaptive slicing strategy was tested with a purpose built vat polymerisation system and numerical engine designed and constructed to serve as a Next......-Gen technology platform. By means of assessing hemispherical manufactured test specimen and through 3D surface mapping with variable-focus microscopy and confocal microscopy, a balance between minimal loss of surface quality with a maximal increase of manufacturing rate has been identified as a simple angle...

  18. Height at Ages 7-13 Years in Relation to Developing Type 2 Diabetes Throughout Adult Life

    DEFF Research Database (Denmark)

    Bjerregaard, Lise G; Jensen, Britt W; Baker, Jennifer L

    2017-01-01

    measured at ages 7-13 years. Hazard ratios (HR) of type 2 diabetes (age ≥30 years) were estimated without and with adjustment for birthweight and BMI. RESULTS: In men, associations between height and type 2 diabetes changed from inverse for below-average heights at age 7 years to positive for above...... for BMI, short childhood height at all ages and greater growth during childhood are associated with an increased risk of type 2 diabetes, suggesting that this period of life warrants mechanistic investigations.......BACKGROUND: Short adults have an increased risk of type 2 diabetes. Although adult height results from childhood growth, the effects of height and growth trajectories during childhood are sparsely investigated. We investigated sex-specific associations between childhood height, growth and adult...

  19. End height of fireball as a function of their residual kinetic energy

    International Nuclear Information System (INIS)

    Revelle, D.O.

    1987-01-01

    Previous analyses of meteoroid compositional groupings have utilized the end height of fireballs as a diagnostic tool. From an observational perspective this definition is straight forward, but from a theoretical viewpoint there are problems with using this operational definition. In order to realistically assess the estimated geometric uncertainty of + 1 km in the observed end height, a theoretical definition of the end height of meteoritic fireballs is proposed using the results from the integral radiation efficiency model of ReVelle. Three photographed and recovered meteorites are used as a calibration for this proposed definition. This definition was used to evaluate the end height of all fireballs that were deduced by Wetherill and ReVelle as being meteoritic. In almost all cases the theoretical values are lower than the observed values, in some cases as much as 5 km lower. A preliminary summary of results are given

  20. The effect of different trap height on the diversity of sap beetle (Coleoptera: Nitidulidae)

    Science.gov (United States)

    Rahim, Nor Atikah Abdul; Yaakop, Salmah

    2018-04-01

    This paper aim to measure the diversity and abundance of sap beetles in oil palm plantation in Malaysia on different heights, 1.5m and 2.5m above ground. A total 0f 20 baited traps were set up in Felda Lui Muda, Negeri Sembilan and located along three transects. The sap beetles collected weekly for a month and identified until species level and the diversity indexes were measured using Evenness Index (E), Shannon-Wiener Index (H'), Simpson's Index (D') and Margalef's Index (R'). All the diversity indexes indicated that the diversity on the lower height above the ground is higher than the upper height The result also shows that there are significant difference (p<0.05) when tested with t-test between the numbers of individuals on the different trap height although the number of species shows different results.

  1. Among-tree variability and feedback effects result in different growth responses to climate change at the upper treeline in the Swiss Alps.

    Science.gov (United States)

    Jochner, Matthias; Bugmann, Harald; Nötzli, Magdalena; Bigler, Christof

    2017-10-01

    Upper treeline ecotones are important life form boundaries and particularly sensitive to a warming climate. Changes in growth conditions at these ecotones have wide-ranging implications for the provision of ecosystem services in densely populated mountain regions like the European Alps. We quantify climate effects on short- and long-term tree growth responses, focusing on among-tree variability and potential feedback effects. Although among-tree variability is thought to be substantial, it has not been considered systematically yet in studies on growth-climate relationships. We compiled tree-ring data including almost 600 trees of major treeline species ( Larix decidua , Picea abies , Pinus cembra , and Pinus mugo ) from three climate regions of the Swiss Alps. We further acquired tree size distribution data using unmanned aerial vehicles. To account for among-tree variability, we employed information-theoretic model selections based on linear mixed-effects models (LMMs) with flexible choice of monthly temperature effects on growth. We isolated long-term trends in ring-width indices (RWI) in interaction with elevation. The LMMs revealed substantial amounts of previously unquantified among-tree variability, indicating different strategies of single trees regarding when and to what extent to invest assimilates into growth. Furthermore, the LMMs indicated strongly positive temperature effects on growth during short summer periods across all species, and significant contributions of fall ( L. decidua ) and current year's spring ( L. decidua , P. abies ). In the longer term, all species showed consistently positive RWI trends at highest elevations, but different patterns with decreasing elevation. L. decidua exhibited even negative RWI trends compared to the highest treeline sites, whereas P. abies , P. cembra , and P. mugo showed steeper or flatter trends with decreasing elevation. This does not only reflect effects of ameliorated climate conditions on tree

  2. The determination of the mixing height. Current progress and problems

    Energy Technology Data Exchange (ETDEWEB)

    Gryning, S.E.; Beyrich, F.; Batchvarova, E. [eds.

    1997-10-01

    This report contains extended abstracts of presentations given at a EURASAP Workshop on The Determination of the Mixing Height - Current Progress and Problems. The Workshop, initiated from discussions with Peter Builtjes, was held at Risoe National Laboratory 1-3 October 1997 within the framework of EURASAP (European Association for the Sciences of Air Pollution). The specific topics and chairpersons of the Workshop were: Theoretical Considerations (Sven-Erik Gryning), Mixing Height Estimation from Turbulence Measurements and In-Situ Soundings (Douw Steyn), Mixing Height Determination from NWP-Models (Han van Dop), Climatology and Global Aspects (Werner Klug), Mixing Height Determination from Remote Systems (Werner Klug), Verification of Mixing Height Parameterizations and Models (Frank Beyrich), Mixing Height over Complex Terrain (Ekaterina Batchvarova), Internal Boundary Layers: Mixing Height in Coastal Areas and Over Cities (Allen White). The discussion at the end of the Workshop was chaired by Robert Bornstein. (au)

  3. Colored Height and Shaded Relief, Central America

    Science.gov (United States)

    2002-01-01

    Panama, Costa Rica, Nicaragua, El Salvador, Honduras, Guatemala, Belize, southern Mexico and parts of Cuba and Jamaica are all seen in this image from NASA's Shuttle Radar Topography Mission. The dominant feature of the northern part of Central America is the Sierra Madre Range, spreading east from Mexico between the narrow Pacific coastal plain and the limestone lowland of the Yucatan Peninsula. Parallel hill ranges sweep across Honduras and extend south, past the Caribbean Mosquito Coast to lakes Managua and Nicaragua. The Cordillera Central rises to the south, gradually descending to Lake Gatun and the Isthmus of Panama. A highly active volcanic belt runs along the Pacific seaboard from Mexico to Costa Rica.High-quality satellite imagery of Central America has, until now, been difficult to obtain due to persistent cloud cover in this region of the world. The ability of SRTM to penetrate clouds and make three-dimensional measurements has allowed the generation of the first complete high-resolution topographic map of the entire region. This map was used to generate the image.Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow, red, and magenta, to white at the highest elevations.For an annotated version of this image, please select Figure 1, below: [figure removed for brevity, see original site] (Large image: 9 mB jpeg)Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on February 11, 2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar that flew twice on the Space Shuttle Endeavour in 1994. The Shuttle Radar Topography Mission was designed to collect

  4. World Globes, Shaded Relief and Colored Height

    Science.gov (United States)

    2003-01-01

    These images of the world were generated with data from the Shuttle Radar Topography Mission (SRTM). The SRTM Project has recently released a new global data set called SRTM30, where the original one arcsecond of latitude and longitude resolution (about 30 meters, or 98 feet, at the equator) was reduced to 30 arcseconds (about 928 meters, or 1496 feet.) These images were created from that data set and show the Earth as it would be viewed from a point in space centered over the Americas, Africa and the western Pacific.Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise,Washington, D.C.Orientation: North toward the top Image Data: shaded and colored SRTM elevation model Original Data Resolution: SRTM 1 arcsecond (about 30 meters or 98 feet

  5. Colored Height and Shaded Relief, Kamchatka Peninsula

    Science.gov (United States)

    2002-01-01

    Russia's Kamchatka Peninsula, lying between the Sea of Okhotsk to the west and the Bering Sea and Pacific Ocean to the east, is one of the most active volcanic regions along the Pacific Ring of Fire. It covers an area about the size of Colorado but contains more than 100 volcanoes stretching across the 1000-kilometer-long (620-mile-long) land mass. A dozen or more of these have active vents, with the youngest located along the eastern half of the peninsula. This color-coded shaded relief image, generated with data from the Shuttle Radar Topography Mission (SRTM), shows Kamchatka's volcanic nature to dramatic effect.Kliuchevskoi, one of the most active and renowned volcanoes in the world, dominates the main cluster of volcanoes called the Kliuchi group, visible as a circular feature in the center-right of the image. The two other main volcanic ranges lie along northeast-southwest lines, with the older, less active range occupying the center and western half of Kamchatka. The younger, more active belt begins at the southernmost point of the peninsula and continues upward along the Pacific coastline.Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the north-south direction, so northern slopes appear bright and southern slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and brown to white at the highest elevations.The Shuttle Radar Topography Mission flew aboard the Space Shuttle Endeavour, launched on February 11, 2000. The mission used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar that flew twice on the Space Shuttle Endeavour in 1994. The Shuttle Radar Topography Mission was designed to collect three-dimensional measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (200

  6. Ireland, Shaded Relief and Colored Height

    Science.gov (United States)

    2005-01-01

    The island of Ireland comprises a large central lowland of limestone with a relief of hills surrounded by a discontinuous border of coastal mountains which vary greatly in geological structure. The mountain ridges of the south are composed of old red sandstone separated by limestone river valleys. Granite predominates in the mountains of Galway, Mayo and Donegal in the west and north-west and in Counties Down and Wicklow on the east coast, while a basalt plateau covers much of the north-east of the country. The central plain, which is broken in places by low hills, is extensively covered with glacial deposits of clay and sand. It has considerable areas of bog and numerous lakes. The island has seen at least two general glaciations and everywhere ice-smoothed rock, mountain lakes, glacial valleys and deposits of glacial sand, gravel and clay mark the passage of the ice. Two visualization methods were combined to produce this image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency

  7. Validity of self-reported weight and height: a cross-sectional study among Malaysian adolescents

    Directory of Open Access Journals (Sweden)

    C. C. Kee

    2017-06-01

    Full Text Available Abstract Background Self-reported weight and height are commonly used in lieu of direct measurements of weight and height in large epidemiological surveys due to inevitable constraints such as budget and human resource. However, the validity of self-reported weight and height, particularly among adolescents, needs to be verified as misreporting could lead to misclassification of body mass index and therefore overestimation or underestimation of the burden of BMI-related diseases. The objective of this study was to determine the validity of self-reported weight and height among Malaysian secondary school children. Methods Both self-reported and directly measured weight and height of a subgroup of 663 apparently healthy schoolchildren from the Malaysian Adolescent Health Risk Behaviour (MyAHRB survey 2013/2014 were analysed. Respondents were required to report their current body weight and height via a self-administrative questionnaire before they were measured by investigators. The validity of self-reported against directly measured weight and height was examined using intraclass correlation coefficient (ICC, the Bland-Altman plot and weighted Kappa statistics. Results There was very good intraclass correlation between self-reported and directly measured weight [r = 0.96, 95% confidence interval (CI: 0.93, 0.97] and height (r = 0.94, 95% CI: 0.90, 0.96. In addition the Bland-Altman plots indicated that the mean difference between self-reported and direct measurement was relatively small. The mean difference (self-reported minus direct measurements was, for boys: weight, −2.1 kg; height, −1.6 cm; BMI, −0.44 kg/m2 and girls: weight, −1.2 kg; height, −0.9 cm; BMI, −0.3 kg/m2. However, 95% limits of agreement were wide which indicated substantial discrepancies between self-reported and direct measurements method at the individual level. Nonetheless, the weighted Kappa statistics demonstrated a substantial agreement between BMI

  8. Prediction of Canopy Heights over a Large Region Using Heterogeneous Lidar Datasets: Efficacy and Challenges

    Directory of Open Access Journals (Sweden)

    Ranjith Gopalakrishnan

    2015-08-01

    Full Text Available Generating accurate and unbiased wall-to-wall canopy height maps from airborne lidar data for large regions is useful to forest scientists and natural resource managers. However, mapping large areas often involves using lidar data from different projects, with varying acquisition parameters. In this work, we address the important question of whether one can accurately model canopy heights over large areas of the Southeastern US using a very heterogeneous dataset of small-footprint, discrete-return airborne lidar data (with 76 separate lidar projects. A unique aspect of this effort is the use of nationally uniform and extensive field data (~1800 forested plots from the Forest Inventory and Analysis (FIA program of the US Forest Service. Preliminary results are quite promising: Over all lidar projects, we observe a good correlation between the 85th percentile of lidar heights and field-measured height (r = 0.85. We construct a linear regression model to predict subplot-level dominant tree heights from distributional lidar metrics (R2 = 0.74, RMSE = 3.0 m, n = 1755. We also identify and quantify the importance of several factors (like heterogeneity of vegetation, point density, the predominance of hardwoods or softwoods, the average height of the forest stand, slope of the plot, and average scan angle of lidar acquisition that influence the efficacy of predicting canopy heights from lidar data. For example, a subset of plots (coefficient of variation of vegetation heights <0.2 significantly reduces the RMSE of our model from 3.0–2.4 m (~20% reduction. We conclude that when all these elements are factored into consideration, combining data from disparate lidar projects does not preclude robust estimation of canopy heights.

  9. Modelling forest canopy height by integrating airborne LiDAR samples with satellite Radar and multispectral imagery

    Science.gov (United States)

    García, Mariano; Saatchi, Sassan; Ustin, Susan; Balzter, Heiko

    2018-04-01

    Spatially-explicit information on forest structure is paramount to estimating aboveground carbon stocks for designing sustainable forest management strategies and mitigating greenhouse gas emissions from deforestation and forest degradation. LiDAR measurements provide samples of forest structure that must be integrated with satellite imagery to predict and to map landscape scale variations of forest structure. Here we evaluate the capability of existing satellite synthetic aperture radar (SAR) with multispectral data to estimate forest canopy height over five study sites across two biomes in North America, namely temperate broadleaf and mixed forests and temperate coniferous forests. Pixel size affected the modelling results, with an improvement in model performance as pixel resolution coarsened from 25 m to 100 m. Likewise, the sample size was an important factor in the uncertainty of height prediction using the Support Vector Machine modelling approach. Larger sample size yielded better results but the improvement stabilised when the sample size reached approximately 10% of the study area. We also evaluated the impact of surface moisture (soil and vegetation moisture) on the modelling approach. Whereas the impact of surface moisture had a moderate effect on the proportion of the variance explained by the model (up to 14%), its impact was more evident in the bias of the models with bias reaching values up to 4 m. Averaging the incidence angle corrected radar backscatter coefficient (γ°) reduced the impact of surface moisture on the models and improved their performance at all study sites, with R2 ranging between 0.61 and 0.82, RMSE between 2.02 and 5.64 and bias between 0.02 and -0.06, respectively, at 100 m spatial resolution. An evaluation of the relative importance of the variables in the model performance showed that for the study sites located within the temperate broadleaf and mixed forests biome ALOS-PALSAR HV polarised backscatter was the most important

  10. Are Anxiety and Depression Just as Stable as Personality During Late Adolescence? Results From a Three-Year Longitudinal Latent Variable Study

    Science.gov (United States)

    Prenoveau, Jason M.; Craske, Michelle G.; Zinbarg, Richard E.; Mineka, Susan; Rose, Raphael D.; Griffith, James W.

    2012-01-01

    Although considerable evidence shows that affective symptoms and personality traits demonstrate moderate to high relative stabilities during adolescence and early adulthood, there has been little work done to examine differential stability among these constructs or to study the manner in which the stability of these constructs is expressed. The present study used a three-year longitudinal design in an adolescent/young adult sample to examine the stability of depression symptoms, social phobia symptoms, specific phobia symptoms, neuroticism, and extraversion. When considering one-, two-, and three-year durations, anxiety and personality stabilities were generally similar and typically greater than the stability of depression. Comparison of various representations of a latent variable trait-state-occasion (TSO) model revealed that whereas the full TSO model was the best representation for depression, a trait stability model was the most parsimonious of the best-fitting models for the anxiety and personality constructs. Over three years, the percentages of variance explained by the trait component for the anxiety and personality constructs (73– 84%) were significantly greater than that explained by the trait component for depression (46%). These findings indicate that symptoms of depression are more episodic in nature, whereas symptoms of anxiety are more similar to personality variables in their expression of stability. PMID:21604827

  11. An examination of environmental correlates with childhood height-for-age in Ghana.

    Science.gov (United States)

    Nikoi, Ebenezer; Anthamatten, Peter

    2013-01-01

    The relationship between a child's environment and nutritional status is difficult to examine yet could offer an important guide to policy. The objective of the present work was to examine individual and environmental correlates with childhood height-for-age in Ghana. Data were derived from the 2008 MEASURE Demographic and Health Survey in Ghana, the 2000 Ghana Population and Housing Census, and the World Wide Fund for Nature's eco-regions database. A generalized linear mixed regression model was used to estimate the effects of individual and environmental correlates on height-for-age. The study examined 2225 Ghanaian children aged 0-59 months. The setting was all districts in Ghana for the year 2008. After accounting for individual characteristics of children, mothers and households, height-for-age was significantly associated with population density. Other significantly associated variables in the final model were the age of the child, vaccination status, the size of the child at birth, months of breast-feeding, mother's BMI, whether the child's mother had health insurance and wealth quintile. In addition to a number of characteristics of the children and their households, the social milieu is important to understanding differences in height-for-age among children in Ghana. The biophysical environment was not associated with height-for-age.

  12. Hilar height ratio in normal Korea

    International Nuclear Information System (INIS)

    Yoo, Kyung Ho; Lee, Nam Joon; Seol, Hae Young; Chung, Kyoo Byung

    1979-01-01

    Hilar displacement is one of the significant sign of pulmonary volume change. The hilar height ratio (HHR) is a value that express the normal position of hilum in its hemithorax, and it is calculated by dividing the distance from the hilum to the lung apex by the distance from the hilum to the diaphragm. Displacement of one hilum is usually easy to detect but both are displaced in the same direction especially, recognition is more difficult. Knowledge of normal HHR allows evaluation of hilar positional change even when the relative hilar position are not altered. Normal chest PA views of 275 cases taken at Korea University Hospital during the period of April 1978 to Jun 1979 were analyzed. The right hilum is positioned in lower half of the right hemithorax, while the left hilum is situated in the upper half of left hemithorax. The difference of hilar ratio according to age group is slight, but there is significant difference between right-HHR and left-HHR. The value of right-HHR is 1.28 ± 0.14, the value of left-HHR is 0.88 ± 0.09.

  13. Clinical longitudinal standards for height, weight, height velocity, weight velocity, and stages of puberty.

    Science.gov (United States)

    Tanner, J M; Whitehouse, R H

    1976-01-01

    New charts for height, weight, height velocity, and weight velocity are presented for clinical (as opposed to population survey) use. They are based on longitudinal-type growth curves, using the same data as in the British 1965 growth standards. In the velocity standards centiles are given for children who are early- and late-maturing as well as for those who mature at the average age (thus extending the use of the previous charts). Limits of normality for the age of occurrence of the adolescent growth spurt are given and also for the successive stages of penis, testes, and pubic hair development in boys, and for stages of breast and pubic hair development in girls. PMID:952550

  14. Mathematical equation for prediction of cat mandibular canal height dimension based on canine tooth width measurement.

    Science.gov (United States)

    Santos, Miguel; Carreira, L Miguel

    2016-06-01

    The present study was performed in a sample of 33 cats and aimed (1) to characterise the mandible height (Mh), mandibular canal height (MCh) and the distance between the interdental alveolar margin and the mandibular canal (dIAM-MC); and (2) to develop a mathematical model for dimension prediction of MCh using the patient's age, weight (Wg) and canine tooth width at the free gingival margin level (wCGM) that was easily accessible during the oral examination. Age, sex, breed, weight, skull type and the wCGM were the recorded variables for each patient. Right and left lateral view skull radiographs were made followed by measurements of the mandible anatomical structures, taken between the third premolar distal root and the fourth premolar proximal root. Results were considered statistically significant for P values <0.05, and statistical analysis was performed using SPSS software. We observed a strong correlation only between wCGM and MCh, and a prediction mathematical model was developed to calculate the MCh, with a standard error of only 0.4 mm. Our study allows a surgeon to establish relationships between a physical parameter, such as wCGM, evaluated in an oral examination, and the mandibular canal, which is a very important anatomical structure to consider in surgical procedures. Ideally, surgeons should always plan their mandible work only after obtaining a final diagnosis achieved through the use of complementary imaging exams, such as intra- and extra-oral radiographs. Thus, this mathematical equation offers an additional tool, providing more information on the relationships between oral anatomical structures, reducing the risk of iatrogenic lesions and promoting patient safety. © ISFM and AAFP 2015.

  15. Satellite altimetry in sea ice regions - detecting open water for estimating sea surface heights

    Science.gov (United States)

    Müller, Felix L.; Dettmering, Denise; Bosch, Wolfgang

    2017-04-01

    The Greenland Sea and the Farm Strait are transporting sea ice from the central Arctic ocean southwards. They are covered by a dynamic changing sea ice layer with significant influences on the Earth climate system. Between the sea ice there exist various sized open water areas known as leads, straight lined open water areas, and polynyas exhibiting a circular shape. Identifying these leads by satellite altimetry enables the extraction of sea surface height information. Analyzing the radar echoes, also called waveforms, provides information on the surface backscatter characteristics. For example waveforms reflected by calm water have a very narrow and single-peaked shape. Waveforms reflected by sea ice show more variability due to diffuse scattering. Here we analyze altimeter waveforms from different conventional pulse-limited satellite altimeters to separate open water and sea ice waveforms. An unsupervised classification approach employing partitional clustering algorithms such as K-medoids and memory-based classification methods such as K-nearest neighbor is used. The classification is based on six parameters derived from the waveform's shape, for example the maximum power or the peak's width. The open-water detection is quantitatively compared to SAR images processed while accounting for sea ice motion. The classification results are used to derive information about the temporal evolution of sea ice extent and sea surface heights. They allow to provide evidence on climate change relevant influences as for example Arctic sea level rise due to enhanced melting rates of Greenland's glaciers and an increasing fresh water influx into the Arctic ocean. Additionally, the sea ice cover extent analyzed over a long-time period provides an important indicator for a globally changing climate system.

  16. Comparisons of chewing rhythm, craniomandibular morphology, body mass and height between mothers and their biological daughters.

    Science.gov (United States)

    Cho, Catherine; Louie, Ke'ale; Maawadh, Ahmed; Gerstner, Geoffrey E

    2015-11-01

    To study and compare the relationships between mean chewing cycle duration, selected cephalometric variables representing mandibular length, face height, etc., measured in women and in their teenage or young-adult biological daughters. Daughters were recruited from local high schools and the University of Michigan School of Dentistry. Selection criteria included healthy females with full dentition, 1st molar occlusion, no active orthodontics, no medical conditions nor medication use that could interfere with normal masticatory motor function. Mothers had to be biologically related to their daughters. All data were obtained in the School of Dentistry. Measurements obtained from lateral cephalograms included: two "jaw length" measures, condylion-gnathion and gonion-gnathion, and four measures of facial profile including lower anterior face height, and angles sella-nasion-A point (SNA), sella-nasion-B point (SNB) and A point-nasion-B point (ANB). Mean cycle duration was calculated from 60 continuous chewing cycles, where a cycle was defined as the time between two successive maximum jaw openings in the vertical dimension. Other variables included subject height and weight. Linear and logistic regression analyses were used to evaluate the mother-daughter relationships and to study the relationships between cephalometric variables and chewing cycle duration. Height, weight, Co-Gn and Go-Gn were significantly correlated between mother-daughter pairs; however, mean cycle duration was not (r(2)=0.015). Mean cycle duration was positively correlated with ANB and height in mothers, but negatively correlated with Co-Gn in daughters. Chewing rate is not correlated between mothers and daughters in humans. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Rainfall height stochastic modelling as a support tool for landslides early warning

    Science.gov (United States)

    Capparelli, G.; Giorgio, M.; Greco, R.; Versace, P.

    2009-04-01

    Occurrence of landslides is uneasy to predict, since it is affected by a number of variables, such as mechanical and hydraulic soil properties, slope morphology, vegetation coverage, rainfall spatial and temporal variability. Although heavy landslides frequently occurred in Campania, southern Italy, during the last decade, no complete data sets are available for natural slopes where landslides occurred. As a consequence, landslide risk assessment procedures and early warning systems in Campania still rely on simple empirical models based on correlation between daily rainfall records and observed landslides, like FLAIR model [Versace et al., 2003]. Effectiveness of such systems could be improved by reliable quantitative rainfall prediction. In mountainous areas, rainfall spatial and temporal variability are very pronounced due to orographic effects, making predictions even more complicated. Existing rain gauge networks are not dense enough to resolve the small scale spatial variability, and the same limitation of spatial resolution affects rainfall height maps provided by radar sensors as well as by meteorological physically based models. Therefore, analysis of on-site recorded rainfall height time series still represents the most effective approach for a reliable prediction of local temporal evolution of rainfall. Hydrological time series analysis is a widely studied field in hydrology, often carried out by means of autoregressive models, such as AR and ARMA [Box and Jenkins, 1976]. Sometimes exogenous information coming from additional series of observations is also taken into account, and the models are called ARX and ARMAX (e.g. Salas [1992]). Such models gave the best results when applied to the analysis of autocorrelated hydrological time series, like river flow or level time series. Conversely, they are not able to model the behaviour of intermittent time series, like point rainfall height series usually are, especially when recorded with short sampling time

  18. Assessing Eruption Column Height in Ancient Flood Basalt Eruptions

    Science.gov (United States)

    Glaze, Lori S.; Self, Stephen; Schmidt, Anja; Hunter, Stephen J.

    2015-01-01

    A buoyant plume model is used to explore the ability of flood basalt eruptions to inject climate-relevant gases into the stratosphere. An example from the 1986 Izu-Oshima basaltic fissure eruption validates the model's ability to reproduce the observed maximum plume heights of 12-16 km above sea level, sustained above fire-fountains. The model predicts maximum plume heights of 13-17 km for source widths of between 4-16 m when 32% (by mass) of the erupted magma is fragmented and involved in the buoyant plume (effective volatile content of 6 wt%). Assuming that the Miocene-age Roza eruption (part of the Columbia River Basalt Group) sustained fire-fountains of similar height to Izu-Oshima (1.6 km above the vent), we show that the Roza eruption could have sustained buoyant ash and gas plumes that extended into the stratosphere at approximately 45 deg N. Assuming 5 km long active fissure segments and 9000 Mt of SO2 released during explosive phases over a 10-15 year duration, the approximately 180 km of known Roza fissure length could have supported approximately 36 explosive events/phases, each with a duration of 3-4 days. Each 5 km fissure segment could have emitted 62 Mt of SO2 per day into the stratosphere while actively fountaining, the equivalent of about three 1991 Mount Pinatubo eruptions per day. Each fissure segment could have had one to several vents, which subsequently produced lava without significant fountaining for a longer period within the decades-long eruption. Sensitivity of plume rise height to ancient atmospheric conditions is explored. Although eruptions in the Deccan Traps (approximately 66 Ma) may have generated buoyant plumes that rose to altitudes in excess of 18 km, they may not have reached the stratosphere because the tropopause was substantially higher in the late Cretaceous. Our results indicate that some flood basalt eruptions, such as Roza, were capable of repeatedly injecting large masses of SO2 into the stratosphere. Thus sustained

  19. Comparative evaluation of hemodynamic and respiratory parameters during mechanical ventilation with two tidal volumes calculated by demi-span based height and measured height in normal lungs

    Directory of Open Access Journals (Sweden)

    L Mousavi Seresht

    2014-01-01

    Full Text Available Background : Appropriate determination of tidal volume (VT is important for preventing ventilation induced lung injury. We compared hemodynamic and respiratory parameters in two conditions of receiving VTs calculated by using body weight (BW, which was estimated by measured height (HBW or demi-span based body weight (DBW. Materials and Methods : This controlled-trial was conducted in St. Alzahra Hospital in 2009 on American Society of Anesthesiologists (ASA I and II, 18-65-years-old patients. Standing height and weight were measured and then height was calculated using demi-span method. BW and VT were calculated with acute respiratory distress syndrome-net formula. Patients were randomized and then crossed to receive ventilation with both calculated VTs for 20 min. Hemodynamic and respiratory parameters were analyzed with SPSS version 20.0 using univariate and multivariate analyses. Results : Forty nine patients were studied. Demi-span based body weight and thus VT (DTV were lower than Height based body weight and VT (HTV (P = 0.028, in male patients (P = 0.005. Difference was observed in peak airway pressure (PAP and airway resistance (AR changes with higher PAP and AR at 20 min after receiving HTV compared with DTV. Conclusions : Estimated VT based on measured height is higher than that based on demi-span and this difference exists only in females, and this higher VT results higher airway pressures during mechanical ventilation.

  20. Precise plant height monitoring and biomass estimation with Terrestrial Laser Scanning in paddy rice

    Directory of Open Access Journals (Sweden)

    N. Tilly

    2013-10-01

    Full Text Available Optimizing crop management is a major topic in the field of precision agriculture as the growing world population puts pressure on the efficiency of field production. Accordingly, methods to measure plant parameters with the needed precision and within-field resolution are required. Studies show that Terrestrial Laser Scanning (TLS is a suitable method to capture small objects like crop plants. In this contribution, the results of multi-temporal surveys on paddy rice fields with the TLS system Riegl LMS-Z420i are presented. Three campaigns were carried out during the key vegetative stage of rice plants in the growing period 2012 to monitor the plant height. The TLS-derived point clouds are interpolated to visualize plant height above ground as crop surface models (CSMs with a high resolution of 0.01 m. Spatio-temporal differences within the data of one campaign and between consecutive campaigns can be detected. The results were validated against manually measured plant heights with a high correlation (R2 = 0.71. Furthermore, the dependence of actual biomass from plant height was evaluated. To the present, no method for the non-destructive determination of biomass is found yet. Thus, plant parameters, like the height, have to be used for biomass estimations. The good correlation (R2 = 0.66 leads to the assumption that biomass can be estimated from plant height measurements. The results show that TLS can be considered as a very promising tool for precision agriculture.

  1. Validity of self-reported weight and height: a cross-sectional study among Malaysian adolescents.

    Science.gov (United States)

    Kee, C C; Lim, K H; Sumarni, M G; Teh, C H; Chan, Y Y; Nuur Hafizah, M I; Cheah, Y K; Tee, E O; Ahmad Faudzi, Y; Amal Nasir, M

    2017-06-02

    and the direct measurements (kappa = 0.76, 95% CI: 0.67, 0.84). Our results show that the self-reported weight and height were consistent with direct measurements and therefore can be used in assessing the nutritional status of Malaysian school children from the age of 13 to 17 years old in epidemiological studies and for surveillance purposes when direct measurements are not feasible, but not for assessing nutritional status at the individual level.

  2. The Impact of Variable Wind Shear Coefficients on Risk Reduction of Wind Energy Projects.

    Science.gov (United States)

    Corscadden, Kenneth W; Thomson, Allan; Yoonesi, Behrang; McNutt, Josiah

    2016-01-01

    Estimation of wind speed at proposed hub heights is typically achieved using a wind shear exponent or wind shear coefficient (WSC), variation in wind speed as a function of height. The WSC is subject to temporal variation at low and high frequencies, ranging from diurnal and seasonal variations to disturbance caused by weather patterns; however, in many cases, it is assumed that the WSC remains constant. This assumption creates significant error in resource assessment, increasing uncertainty in projects and potentially significantly impacting the ability to control gird connected wind generators. This paper contributes to the body of knowledge relating to the evaluation and assessment of wind speed, with particular emphasis on the development of techniques to improve the accuracy of estimated wind speed above measurement height. It presents an evaluation of the use of a variable wind shear coefficient methodology based on a distribution of wind shear coefficients which have been implemented in real time. The results indicate that a VWSC provides a more accurate estimate of wind at hub height, ranging from 41% to 4% reduction in root mean squared error (RMSE) between predicted and actual wind speeds when using a variable wind shear coefficient at heights ranging from 33% to 100% above the highest actual wind measurement.

  3. Cross-sectional study of height and weight in the population of Andalusia from age 3 to adulthood

    Directory of Open Access Journals (Sweden)

    Cosano Carlos

    2008-07-01

    Full Text Available Abstract Background and objectives In Andalusia there were no studies including a representative sample of children and adolescent population assessing growth and weight increase. Our objectives were to develop reference standards for weight, height and BMI for the Andalusian pediatric population, from 3 to 18 years of age for both genders, and to identify the final adult height in Andalusia. Subjects and methods Two samples were collected. The first included individuals from 3 to 18 years of age (3592 girls and 3605 boys. They were stratified according type of study center, size of population of origin, age (32 categories of 0.5 years and gender, using cluster sampling. Subjects from >18 to 23 years of age (947 women and 921 men were sampled in 6 non-university educational centers and several university centers in Granada. Exclusion criteria included sons of non-Spanish mother or father, and individuals with chronic conditions and/or therapies affecting growth. Two trained fellows collected the data through February to December 2004, for the first sample, and through January to May 2005, for the second. Reference curves were adjusted using Cole's LMS method, and the quality of the adjustment was assessed using the tests proposed by Royston. In addition, a sensitivity analysis was applied to the final models obtained. Results Data for 9065 cases (4539 women and 4526 men were obtained; 79.39% (n = 7197 in the up to 18 years of age group. In the first sampling only 0.07% (3 girls and 2 boys refused to participate in the study. In addition, 327 students (4.5% were absent when sampling was done. We present mean and standard deviation fort height, weight and BMI at 0.5 years intervals, from 3 to 23 years of age, for both genders. After adjustment with the different models, percentiles for height, weight (percentiles 3, 5, 10, 25, 50, 75, 90, 95, and 97 and BMI (percentiles 3, 5, 50, 85, 95, and 97 are presented for both genders. Conclusion This is

  4. The physics and chemistry of the Schottky barrier height

    International Nuclear Information System (INIS)

    Tung, Raymond T.

    2014-01-01

    The formation of the Schottky barrier height (SBH) is a complex problem because of the dependence of the SBH on the atomic structure of the metal-semiconductor (MS) interface. Existing models of the SBH are too simple to realistically treat the chemistry exhibited at MS interfaces. This article points out, through examination of available experimental and theoretical results, that a comprehensive, quantum-mechanics-based picture of SBH formation can already be constructed, although no simple equations can emerge, which are applicable for all MS interfaces. Important concepts and principles in physics and chemistry that govern the formation of the SBH are described in detail, from which the experimental and theoretical results for individual MS interfaces can be understood. Strategies used and results obtained from recent investigations to systematically modify the SBH are also examined from the perspective of the physical and chemical principles of the MS interface

  5. Small scale currents and ocean wave heights: from today's models to future satellite observations with CFOSAT and SKIM

    Science.gov (United States)

    Ardhuin, Fabrice; Gille, Sarah; Menemenlis, Dimitris; Rocha, Cesar; Rascle, Nicolas; Gula, Jonathan; Chapron, Bertrand

    2017-04-01

    Tidal currents and large oceanic currents, such as the Agulhas, Gulf Stream and Kuroshio, are known to modify ocean wave properties, causing extreme sea states that are a hazard to navigation. Recent advances in the understanding and modeling capability of ocean currents at scales of 10 km or less have revealed the ubiquitous presence of fronts and filaments. Based on realistic numerical models, we show that these structures can be the main source of variability in significant wave heights at scales less than 200 km, including important variations at 10 km. This current-induced variability creates gradients in wave heights that were previously overlooked and are relevant for extreme wave heights and remote sensing. The spectrum of significant wave heights is found to be of the order of 70⟨Hs ⟩2/(g2⟨Tm0,-1⟩2) times the current spectrum, where ⟨Hs ⟩ is the spatially-averaged significant wave height, ⟨Tm0,-1⟩ is the average energy period, and g is the gravity acceleration. This small scale variability is consistent with Jason-3 and SARAL along-track variability. We will discuss how future satellite mission with wave spectrometers can help observe these wave-current interactions. CFOSAT is due for launch in 2018, and SKIM is a proposal for ESA Earth Explorer 9.

  6. The parametrization of Coulomb barrier heights and positions using the double folding model

    International Nuclear Information System (INIS)

    Qu, W.W.; Zhang, G.L.; Le, X.Y.

    2011-01-01

    The Coulomb barrier heights and positions are systematically shown with mass numbers and charge radii of the interacting nuclei. The nuclear potential is calculated by using the double folding model with the density-dependence nucleon-nucleon interaction (CDM3Y6). The pocket formulas are obtained for the Coulomb barrier heights and positions by analyzing several hundreds of heavy-ion systems with mass numbers from light nuclei to heavy nuclei. The parameterized formulas can reproduce the calculated barrier heights and positions by using the double folding model within the accuracy of ±1%. Moreover, the results are agreeable with the experimental data. The relation between the barrier height and the barrier position is also studied.

  7. Simulation of three-phase flow and lance height effect on the cavity shape

    Science.gov (United States)

    Dong, Kai; Zhu, Rong; Gao, Wei; Liu, Fu-hai

    2014-06-01

    A three-dimensional computational fluid dynamics (CFD) model was developed to simulate a 150-t top-blown converter. The effect of different lance heights on the cavity shape was investigated using the volume of fluid (VOF) method. Numerical simulation results can reflect the actual molten bath surface waves impinged by the supersonic oxygen jets. With increasing lance height, the cavity depth decreases, and the cavity area, varying like a parabola, increases and then decreases. The cavity area maximizes at the lance height of 1.3 m. Under the three different lance heights simulated in this study, all of the largest impact velocities at the molten bath surface are between 50 m/s and 100 m/s.

  8. Effective pollutant emission heights for atmospheric transport modelling based on real-world information.

    Science.gov (United States)

    Pregger, Thomas; Friedrich, Rainer

    2009-02-01

    Emission data needed as input for the operation of atmospheric models should not only be spatially and temporally resolved. Another important feature is the effective emission height which significantly influences modelled concentration values. Unfortunately this information, which is especially relevant for large point sources, is usually not available and simple assumptions are often used in atmospheric models. As a contribution to improve knowledge on emission heights this paper provides typical default values for the driving parameters stack height and flue gas temperature, velocity and flow rate for different industrial sources. The results were derived from an analysis of the probably most comprehensive database of real-world stack information existing in Europe based on German industrial data. A bottom-up calculation of effective emission heights applying equations used for Gaussian dispersion models shows significant differences depending on source and air pollutant and compared to approaches currently used for atmospheric transport modelling.

  9. Growth in Total Height and Its Components and Cardiometabolic Health in Childhood

    DEFF Research Database (Denmark)

    Haugaard, Line Klingen; Baker, Jennifer Lyn; Perng, Wei

    2016-01-01

    BACKGROUND: Short stature or short legs is associated with cardiometabolic disease. Few studies have addressed this issue in children, incorporated repeated measures, or studied modern cohorts. METHODS: We examined if change in total height, leg length and trunk length between two time points from...... was a cardiometabolic risk score based on sex-specific internal z-scores for systolic blood pressure, waist circumference, homeostatic model assessment of insulin resistance, triglycerides and high-density lipoprotein-cholesterol. RESULTS: Mean (SD) total height was 97.9 (4.5) cm in boys and 97.1 (4.7) cm in girls...... in early childhood and 129.1 (7.2) cm in boys and 128.3 (7.9) cm in girls in mid-childhood. Trunk length constituted about half of total height. In linear regression models adjusted for parental anthropometry and socio-demographics, faster growth in total height, leg length and particularly trunk length...

  10. Height drift correction in non-raster atomic force microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Travis R. [Department of Mathematics, University of California Los Angeles, Los Angeles, CA 90095 (United States); Ziegler, Dominik [Molecular Foundry, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Brune, Christoph [Institute for Computational and Applied Mathematics, University of Münster (Germany); Chen, Alex [Statistical and Applied Mathematical Sciences Institute, Research Triangle Park, NC 27709 (United States); Farnham, Rodrigo; Huynh, Nen; Chang, Jen-Mei [Department of Mathematics and Statistics, California State University Long Beach, Long Beach, CA 90840 (United States); Bertozzi, Andrea L., E-mail: bertozzi@math.ucla.edu [Department of Mathematics, University of California Los Angeles, Los Angeles, CA 90095 (United States); Ashby, Paul D., E-mail: pdashby@lbl.gov [Molecular Foundry, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States)

    2014-02-01

    We propose a novel method to detect and correct drift in non-raster scanning probe microscopy. In conventional raster scanning drift is usually corrected by subtracting a fitted polynomial from each scan line, but sample tilt or large topographic features can result in severe artifacts. Our method uses self-intersecting scan paths to distinguish drift from topographic features. Observing the height differences when passing the same position at different times enables the reconstruction of a continuous function of drift. We show that a small number of self-intersections is adequate for automatic and reliable drift correction. Additionally, we introduce a fitness function which provides a quantitative measure of drift correctability for any arbitrary scan shape. - Highlights: • We propose a novel height drift correction method for non-raster SPM. • Self-intersecting scans enable the distinction of drift from topographic features. • Unlike conventional techniques our method is unsupervised and tilt-invariant. • We introduce a fitness measure to quantify correctability for general scan paths.

  11. Size matters: Perceived depth magnitude varies with stimulus height.

    Science.gov (United States)

    Tsirlin, Inna; Wilcox, Laurie M; Allison, Robert S

    2016-06-01

    Both the upper and lower disparity limits for stereopsis vary with the size of the targets. Recently, Tsirlin, Wilcox, and Allison (2012) suggested that perceived depth magnitude from stereopsis might also depend on the vertical extent of a stimulus. To test this hypothesis we compared apparent depth in small discs to depth in long bars with equivalent width and disparity. We used three estimation techniques: a virtual ruler, a touch-sensor (for haptic estimates) and a disparity probe. We found that depth estimates were significantly larger for the bar stimuli than for the disc stimuli for all methods of estimation and different configurations. In a second experiment, we measured perceived depth as a function of the height of the bar and the radius of the disc. Perceived depth increased with increasing bar height and disc radius suggesting that disparity is integrated along the vertical edges. We discuss size-disparity correlation and inter-neural excitatory connections as potential mechanisms that could account for these results. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Plantar Pressure Variation during Jogging with Different Heel Height

    Directory of Open Access Journals (Sweden)

    Y. D. Gu

    2013-01-01

    Full Text Available This paper presents the key testing and analysis results of an investigation on the effect of heel height on the plantar pressure over different foot areas in jogging. It is important in improving the understanding of jogging with high heels and damage/injury prevention. It can also potentially guide the development of suitable/adaptive exercise schemes in between daily activities with high heels. In this work, plantar pressure data were collected from 10 habituated healthy female subjects (aged 21–25 years at their natural jogging speed with three different conditions: flat heeled shoes (0.8 cm, low heeled shoes (4.0 cm, and high heeled shoes (6.6 cm. Data analysis showed significantly differences in plantar pressure distribution associated with the heel heights with increased pressure in the first metatarsal region and decreased pressure in the lateral metatarsal and midfoot sections. However, there is no significant alteration of plantar pressure in the central area of the forefoot with jogging gait.

  13. Australia, Shaded Relief and Colored Height

    Science.gov (United States)

    2004-01-01

    topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C. Location: 45 to 10 degrees South latitude, 112 to 155 degrees East longitude Orientation: North toward the top, Mercator projection Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

  14. Guiana Highlands, Shaded Relief and Colored Height

    Science.gov (United States)

    2003-01-01

    Doyle's 1912 best-seller 'The Lost World.'Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Imagery and Mapping Agency (NIMA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise,Washington, D.C.Location: 0.2 South to 8.7 degrees North latitude, 60 to 67.9 degrees West longitude Orientation: North toward the top Image Data: shaded and colored SRTM30 and GTOPO30 elevation models Data Resolution: SRTM 30 arcsecond (about 928 meters or 1496 feet) Date Acquired: February 2000 for SRTM

  15. Olduvai Gorge, Shaded Relief and Colored Height

    Science.gov (United States)

    2004-01-01

    topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations. Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D measurements of the Earth's surface. To collect the 3-D data, engineers added a 60-meter (approximately 200-foot) mast, installed additional C-band and X-band antennas, and improved tracking and navigation devices. The mission is a cooperative project between NASA, the National Geospatial-Intelligence Agency (NGA) of the U.S. Department of Defense and the German and Italian space agencies. It is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., for NASA's Earth Science Enterprise, Washington, D.C. Location: 3 degrees south latitude, 35 degrees east longitude Orientation: North toward the top, Mercator projection Size: 223 by 223 kilometers (138 by 138 miles) Image Data: shaded and colored SRTM elevation model Date Acquired: February 2000

  16. France, Shaded Relief and Colored Height

    Science.gov (United States)

    2003-01-01

    This image of France was generated with data from the Shuttle Radar Topography Mission (SRTM). For this broad view the resolution of the data was reduced to 6 arcseconds (about 185 meters north-south and 127 meters east-west), resampled to a Mercator projection, and the French border outlined. Even at this decreased resolution the variety of landforms comprising the country is readily apparent.The upper central part of this scene is dominated by the Paris Basin, which consists of a layered sequence of sedimentary rocks. Fertile soils over much of the area make good agricultural land. The Normandie coast to the upper left is characterized by high, chalk cliffs, while the Brittany coast (the peninsula to the left) is highly indented where deep valleys were drowned by the sea, and the Biscay coast to the southwest is marked by flat, sandy beaches.To the south, the Pyrenees form a natural border between France and Spain, and the south-central part of the country is dominated by the ancient Massif Central. Subject to volcanism that has only subsided in the last 10,000 years, these central mountains are separated from the Alps by the north-south trending Rhone River Basin.Two visualization methods were combined to produce the image: shading and color coding of topographic height. The shade image was derived by computing topographic slope in the northwest-southeast direction, so that northwest slopes appear bright and southeast slopes appear dark. Color coding is directly related to topographic height, with green at the lower elevations, rising through yellow and tan, to white at the highest elevations.Elevation data used in this image were acquired by the Shuttle Radar Topography Mission aboard the Space Shuttle Endeavour, launched on Feb. 11, 2000. SRTM used the same radar instrument that comprised the Spaceborne Imaging Radar-C/X-Band Synthetic Aperture Radar (SIR-C/X-SAR) that flew twice on the Space Shuttle Endeavour in 1994. SRTM was designed to collect 3-D

  17. Crown heights in the permanent teeth of 45,X and 45,X/46,XX females.

    Science.gov (United States)

    Pentinpuro, Raija Helena; Lähdesmäki, Raija Eliisa; Niinimaa, Ahti Olavi; Pesonen, Paula Ritva Orvokki; Alvesalo, Lassi Juhani

    2014-11-01

    Previous results regarding human sex chromosome aneuploidies have shown that the X and Y chromosomes affect tooth size and morphology. This study looked for the effect of sex chromosome deficiency on permanent tooth crown heights. The material, from the Finnish KVANTTI Research Project, consisted of 97 45,X females and 15 45,X/46,XX females. The controls were 32 sisters and 28 mothers of the 45,X females, eight sisters and two mothers of the 45,X/46,XX females and 35 female population controls. Crown heights of all the available teeth except third molars on both sides of the jaws were measured from panoramic radiographs with a digital calliper according to the defined procedure. The tooth crown heights were significantly smaller in the 45,X females than in the female population controls, except for the incisors and one canine in the maxilla, whereas the tooth crown heights of the 45,X/46,XX females were close to those of the normal control females. The differences between the 45,X and 45,X/46,XX females were statistically significant, excluding the upper incisor area and a few teeth in the mandible. The effect of the sex chromosome deficiency on permanent tooth crown height is due to the magnitude of lacking sex chromosome material. The present results regarding the 45,X females are parallel to previous findings in Turner patients regarding reduced mesiodistal and labiolingual dimensions and tooth crown heights in the permanent dentition.

  18. Mixing height derived from the DMI-HIRLAM NWP model, and used for ETEX dispersion modelling

    Energy Technology Data Exchange (ETDEWEB)

    Soerensen, J.H.; Rasmussen, A. [Danish Meteorological Inst., Copenhagen (Denmark)

    1997-10-01

    For atmospheric dispersion modelling it is of great significance to estimate the mixing height well. Mesoscale and long-range diffusion models using output from numerical weather prediction (NWP) models may well use NWP model profiles of wind, temperature and humidity in computation of the mixing height. This is dynamically consistent, and enables calculation of the mixing height for predicted states of the atmosphere. In autumn 1994, the European Tracer Experiment (ETEX) was carried out with the objective to validate atmospheric dispersion models. The Danish Meteorological Institute (DMI) participates in the model evaluations with the Danish Emergency Response Model of the Atmosphere (DERMA) using NWP model data from the DMI version of the High Resolution Limited Area Model (HIRLAM) as well as from the global model of the European Centre for Medium-Range Weather Forecast (ECMWF). In DERMA, calculation of mixing heights are performed based on a bulk Richardson number approach. Comparing with tracer gas measurements for the first ETEX experiment, a sensitivity study is performed for DERMA. Using DMI-HIRLAM data, the study shows that optimum values of the critical bulk Richardson number in the range 0.15-0.35 are adequate. These results are in agreement with recent mixing height verification studies against radiosonde data. The fairly large range of adequate critical values is a signature of the robustness of the method. Direct verification results against observed missing heights from operational radio-sondes released under the ETEX plume are presented. (au) 10 refs.

  19. Short Communication. Using high resolution UAV imagery to estimate tree variables in Pinus pinea plantation in Portugal

    Directory of Open Access Journals (Sweden)

    Juan Guerra Hernandez

    2016-07-01

    Research highlights: The results demonstrate that tree variables can be automatically extracted from high resolution imagery. We highlight the use of UAV systems as a fast, reliable and cost‑effective technique for small scale applications. Keywords: Unmanned aerial systems (UAS; forest inventory; tree crown variables; 3D image modelling; canopy height model (CHM; object‑based image analysis (OBIA, structure‑from‑motion (SfM.

  20. Earthquake Scenario-Based Tsunami Wave Heights in the Eastern Mediterranean and Connected Seas

    Science.gov (United States)

    Necmioglu, Ocal; Özel, Nurcan Meral

    2015-12-01

    We identified a set of tsunami scenario input parameters in a 0.5° × 0.5° uniformly gridded area in the Eastern Mediterranean, Aegean (both for shallow- and intermediate-depth earthquakes) and Black Seas (only shallow earthquakes) and calculated tsunami scenarios using the SWAN-Joint Research Centre (SWAN-JRC) code ( Mader 2004; Annunziato 2007) with 2-arcmin resolution bathymetry data for the range of 6.5—Mwmax with an Mw increment of 0.1 at each grid in order to realize a comprehensive analysis of tsunami wave heights from earthquakes originating in the region. We defined characteristic earthquake source parameters from a compiled set of sources such as existing moment tensor catalogues and various reference studies, together with the Mwmax assigned in the literature, where possible. Results from 2,415 scenarios show that in the Eastern Mediterranean and its connected seas (Aegean and Black Sea), shallow earthquakes with Mw ≥ 6.5 may result in coastal w