Design and development of rolled joint for moderator sparger channel of an Indian Pressurised Heavy Water Reactor

International Nuclear Information System (INIS)

Joemon, V.; Sinha, R.K.

1993-01-01

Indian Pressurised Heavy Water Reactors are natural uranium fuelled heavy water moderated and cooled reactors. As per the conventional scheme, the moderator enters through one or more inlet nozzles penetrating the calandria shell and flows out through outlet nozzles. Baffles are fixed at the inlet nozzles for proper distribution of moderator in the calandria and to avoid the impact of the jet on the neighbouring calandria tubes. An alternate scheme for moderator inlet has been conceived and engineered in which three lower peripheral lattice locations of the reactor are converted into moderator inlets. This is achieved by moderator sparger channels each containing a 5 m long perforated zircaloy-2 sparger tube rolled to the calandria tube sheets and extended by stainless steel tubular components (inserts) at both ends of a sparger channel. Moderator enters the sparger channel at both ends and flows into the calandria. In the absence of standard codes for design of rolled joints, it was requires to develop these joints based on trials followed by various tests. this paper discusses the details of the rolled joint developed for this purpose, the details of the trials with test results and optimization of rolling parameters for these joints

Impact of different moderator ratios with light and heavy water cooled reactors in equilibrium states

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2006-01-01

As an issue of sustainable development in the world, energy sustainability using nuclear energy may be possible using several different ways such as increasing breeding capability of the reactors and optimizing the fuel utilization using spent fuel after reprocessing as well as exploring additional nuclear resources from sea water. In this present study the characteristics of light and heavy water cooled reactors for different moderator ratios in equilibrium states have been investigated. The moderator to fuel ratio (MFR) is varied from 0.1 to 4.0. Four fuel cycle schemes are evaluated in order to investigate the effect of heavy metal (HM) recycling. A calculation method for determining the required uranium enrichment for criticality of the systems has been developed by coupling the equilibrium fuel cycle burn-up calculation and cell calculation of SRAC 2000 code using nuclear data library from the JENDL 3.2. The results show a thermal spectrum peak appears for light water coolant and no thermal peak for heavy water coolant along the MFR (0.1 ≤ MFR ≤ 4.0). The plutonium quality can be reduced effectively by increasing the MFR and number of recycled HM. Considering the effect of increasing number of recycled HM; it is also effective to reduce the uranium utilization and to increase the conversion ratio. trans-Plutonium production such as americium (Am) and curium (Cm) productions are smaller for heavy water coolant than light water coolant. The light water coolant shows the feasibility of breeding when HM is recycled with reducing the MFR. Wider feasible area of breeding has been obtained when light water coolant is replaced by heavy water coolant

Direct harvesting of Helium-3 (3He) from heavy water nuclear reactors

International Nuclear Information System (INIS)

Bentoumi, G.; Didsbury, R.; Jonkmans, G.; Rodrigo, L.; Sur, B.

2013-01-01

The thermal neutron activation of deuterium inside a heavy-water-moderated or -cooled nuclear reactor produces a build-up of tritium in the heavy water. The in situ decay of tritium can, for certain reactor types and operating conditions, produce potentially useable amounts of 3 He, which can be directly extracted via the heavy-water cover gas without first separating, collecting and storing tritium outside the reactor. It is estimated that the amount of 3 He available for recovery from the moderator cover gas of a 700 MWe class Pressurized Heavy Water Reactor (PHWR) ranges from 0.1 to 0.7 m 3 (STP) per annum, varying with the tritium activity buildup in the moderator. The harvesting of 3 He would generate approximately 12.7 m 3 (STP) of 3 He, worth more than $30M at current market rates, over a typical 25-year operating cycle of the PHWR. This paper discusses the production of 3 He in the moderator of a PHWR and its extraction from the 4 He moderator cover gas system using conventional methods. (author)

Improvement in fuel utilization in pressurized heavy water reactors due to increased heavy water purity

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1991-01-01

This paper reports that in a pressurized heavy water reactor (PHWR), the reactivity of the reactor and, consequently, the discharge burnup of the fuel depend on the isotopic purity of the heavy water used in the reactor. The optimal purity of heavy water used in PHWRs, in turn, depends on the cost of fabricated uranium fuel and on the incremental cost incurred in improving the heavy water purity. The physics and economics aspects of the desirability of increasing the heavy water purity in PHWRs in India were first examined in 1978. With the cost data available at that time, it was found that improving the heavy water purity from 99.80% to 99.95% was economically attractive. The same problem is reinvestigated with current cost data. Even now, there is sufficient incentive to improve the isotopic purity of heavy water used in PHWRs. Admittedly, the economic advantage that can be derived depends on the cost of the fabricated fuel. Nevertheless, irrespective of the economics, there is also a fairly substantial saving in natural uranium. That the increase in the heavy water purity is to be maintained only in the low-pressure moderator system, and not in the high-pressure coolant system, makes the option of achieving higher fuel burnup with higher heavy water purity feasible

A review of the UKAEA interest in heavy water reactors

International Nuclear Information System (INIS)

Symes, R.J.

1983-01-01

The chapter commences with a brief account of the history of heavy water production and then begins the story of the British use of this moderator in power reactors. This is equated with the introduction and development of the tube reactor as a distinct and important form of reactor construction in contrast with the perhaps better known vessel design that has tended to dominate reactor engineering to date. The account thus includes a succession of reactor designs including the gas and steam cooled heavy water systems in addition to the steam-generating heavy water reactor. The SGHWR was demonstrated by the construction of a substantial prototype, which continues in operation as a flexible and reliable electricity-generating plant. It was also, for a time, identified as the system to be used for Britain's third reactor programme. Today the successful Canadian CANDU power reactors represent the only penetration of heavy water reactor technology into large scale electricity generation. The range of research and experimental reactors using heavy water in their cores is reviewed. (author)

Thorium utilization in heavy water moderated Accelerator Driven Systems

International Nuclear Information System (INIS)

Bajpai, Anil; Degweker, S.B.; Ghosh, Biplab

2011-01-01

Research on Accelerator Driven Systems (ADSs) is being carried out around the world primarily with the objective of waste transmutation. Presently, the volume of waste in India is small and therefore there is little incentive to develop ADS based waste transmutation technology immediately. With limited indigenous U availability and the presence of large Th deposits in the country, there is a clear incentive to develop Th related technologies. India also has vast experience in design, construction and operation of heavy water moderated reactors. Heavy water moderated reactors employing solid Th fuels can be self sustaining, but the discharge burnups are too low to be economical. A possible way to improve the performance such reactors is to use an external neutron source as is done in ADS. This paper discusses our studies on Th utilization in heavy water moderated ADSs. The study is carried out at the lattice level. The time averaged k-infinity of the Th bundle from zero burnup up to the discharge burnup is taken to be the same as the core (ensemble) averaged k-infinity. For the purpose of the analysis we have chosen standard PHWR and AHWR assemblies. Variation of the pitch and coolant (H 2 O/D 2 O) are studied. Both, the once through cycle and the recycling option are studied. In the latter case the study is carried out for various enrichments (% 233 U in Th) of the recycled Th fuel bundles. The code DTF as modified for lattice and burnup calculations (BURNTRAN) was used for carrying out the study. The once through cycle represents the most attractive ADS concept (Th burner ADS) possible for Th utilization. It avoids reprocessing of Th spent fuel and in the ideal situation the use of any fissile material either initially or for sustaining itself. The gain in this system is however rather low requiring a high power accelerator and a substantial fraction of the power generated to be fed back to the accelerator. The self sustaining Th-U cycle in a heavy moderated ADS

A study of the tritium behavior in coolant and moderator system of heavy water reactors

Energy Technology Data Exchange (ETDEWEB)

Kim, S. P.; Song, S. S.; Chae, K. S. and others [Chosun Univ., Gwangju (Korea, Republic of)

1993-12-15

The objectives of this report is to present a regulatory policy on the environmental impact and personnel exposure by understanding the generation, accumulation, environmental release and management of tritium in heavy water reactors. By estimating the tritium concentration at Wolsong nuclear plant site by estimating and forecasting the generation and accumulation of tritium in coolant and moderator systems at Wolsong unit 1, we will study the management and release of tritium at Wolsong units 3 and 4 which are ready for construction. The major activities of this study are as follows : tritium generation and accumulation in heavy water reactor, a quantitative assessment of the accumulation and release of tritium at Wolsong nuclear plant site, heavy water management at Wolsong nuclear plants. The tritium concentration and accumulation trends in the systems at Wolsong unit 1 was estimated. A quantitative assessment of the tritium accumulation and release for Wolsong 2, 3 and 4 based on data from Wolsong 1 was performed. The tritium removal schemes and its long-term management plan were made.

Multidimensional space-time kinetics of a heavy water moderated nuclear reactor

International Nuclear Information System (INIS)

Winn, W.G.; Baumann, N.P.; Jewell, C.E.

1980-01-01

Diffusion theory analysis of a series of multidimensional space-time experiments is appraised in terms of the final experiment of the series. In particular, TRIMHX diffusion calculations were examined for an experiment involving free-fall insertion of a 235 U-bearing rod into a heavy water moderated reactor with a large reflector. The experimental transient flux-tilts were accurately reproduced after cross section adjustments forced agreement between static diffusion calculations and static reactor measurements. The time-dependent features were particularly well modeled, and the bulk of the small discrepancies in space-dependent features should be removable by more refined cross-section adjustments. This experiment concludes a series of space-time experiments that span a wide range of delayed neutron holdback effects. TRIMHX calculations of these experiments demonstrate the accuracy of the modeling employed in the code

Thorium in heavy water reactors

International Nuclear Information System (INIS)

Andersson, G.

1984-12-01

Advanced heavy water reactors can provide energy on a global scale beyond the foreseeable future. Their economic and safety features are promising: 1. The theoretical feasibility of the Self Sufficient Equilibrium Thorium (SSET) concept is confirmed by new calculations. Calculations show that the adjuster rod geometry used in natural uranium CANDU reactors is adequate also for SSET if the absorption in the rods is graded. 2. New fuel bundle designs can permit substantially higher power output from a CANDU reactor. The capital cost for fuel, heavy water and mechanical equipment can thereby be greatly reduced. Progress is possible with the traditional fuel material oxide, but the use of thorium metal gives much larger effects. 3. A promising long range possibility is to use pressure tanks instead of pressure tubes. Heat removal from the core is facilitated. Negative temperature and void coefficients provide inherent safety features. Refuelling under power is no longer needed if control by moderator displacement is used. Reduced quality demand on the fuel permits lower fuel costs. The neutron economy is improved by the absence of pressure and clandria tubes and also by the use of radial and axial blankets. A modular seed blanket design can reduce the Pa losses. The experience from construction of tank designs is good e.g. AAgesta, Attucha. It is now also possible to utilize technology from LWR reactors and the implementation of advanced heavy water reactors would thus be easier than HTR or LMFBR systems. (Author)

Numerical analysis on the calandria tubes in the moderator of a heavy water reactor using OpenFOAM and other codes

International Nuclear Information System (INIS)

Chang, S.M.; Kim, H.T.

2013-01-01

CANDU, a prototype of heavy water reactor is modeled for the moderator system with porous media buoyancy-effect heat-transfer turbulence model. OpenFOAM, a set of C++ classes and libraries developed under the object-oriented concept, is selected as the tool of numerical analysis. The result from this computational code is compared with experiments and other commercial code data through ANSYS-CFX and COMSOL Multi-physics. The three-dimensional code concerning buoyancy force, turbulence, and heat transfer is tested and shown to be successful for the analysis of thermo-hydraulic system of heavy water reactors. (authors)

Assessment of Loss-of-Coolant Effect on Pressurized Heavy Water Reactors

International Nuclear Information System (INIS)

Kim, Won Young; Park, Joo Hwan; Kim, Bong Ghi

2009-01-01

A CANDU reactor is a heavy-water-moderated, natural uranium fuelled reactor with a pressure tube. The reactor contains a horizontal cylindrical vessel (calandria) and each pressure tube is isolated from the heavy-water moderator in a calandria. This allows the moderator system to be operated of a high-pressure and of a high-temperature coolant in pressure tube. This causes the pressurized liquid coolant in the channel to void and therefore give rise to a reactivity transient in the event of a break or fault in the coolant circuit. In particular, all CANDU reactors are well known to have a positive void reactivity coefficient and thus this phenomenon may lead to a positive feedback, which can cause a large power pulse. We assess the loss-of-coolant effect by coolant void reactivity versus fuel burnup, four factor parameters for fresh fuel and equilibrium fuel, reactivity change due to the change of coolant density and reactivity change in the case of half- and full-core coolant

Improvements in gas supply systems for heavy-water moderated reactors

International Nuclear Information System (INIS)

Aubert, G.; Hassig, J.M.; Laurent, N.; Thomas, B.

1964-01-01

In a heavy-water moderated reactor cooled by pressurized gas, an important problem from the point of view, of the reactor block and its economics is the choice of the gas supply system. In the pressure tube solution, the whole of the reactor block structure is at a relatively low temperature, whereas the gas supply equipment is at that of the gas, which is much higher. These parts, through which passes the heat carrying fluid have to present as low a resistance as possible to it so as to avoid costly extra blowing power. Finally, they may only be placed in the reactor block after it has been built; the time required for putting them in position should therefore not be too long. The work reported here concerns the various problems arising in the case of each channel being supplied individually by a tube at the entry and the exit which is connected to a main circuit made up of large size collectors. This individual tubing is sufficiently flexible to absorb the differential expansion and the movement of its ends without stresses or prohibitive reactions being produced; the tubing is also of relatively short length so as to reduce the pressure head of the pressurized gas outside the channels; the small amount of space taken up by the tubing makes it possible to assemble it in a manner which is satisfactory from the point of view both of the time required and of the technical quality. (authors) [fr

Heavy water moderated gas-cooled reactors; Filiere eau lourde - gaz

Energy Technology Data Exchange (ETDEWEB)

Bailly du Bois, B; Bernard, J L; Naudet, R; Roche, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

France has based its main effort for the production of nuclear energy on natural Uranium Graphite-moderated gas-cooled reactors, and has a long term programme for fast reactors, but this country is also engaged in the development of heavy water moderated gas-cooled reactors which appear to present the best middle term prospects. The economy of these reactors, as in the case of Graphite, arises from the use of natural or very slightly enriched Uranium; heavy water can take the best advantages of this fuel cycle and moreover offers considerable development potential because of better reactor performances. A prototype plant EL 4 (70 MW) is under construction and is described in detail in another paper. The present one deals with the programme devoted to the development of this reactor type in France. Reasons for selecting this reactor type are given in the first part: advantages and difficulties are underlined. After reviewing the main technological problems and the Research and Development carried out, results already obtained and points still to be confirmed are reported. The construction of EL 4 is an important step of this programme: it will be a significant demonstration of reactor performances and will afford many experimentation opportunities. Now the design of large power reactors is to be considered. Extension and improvements of the mechanical structures used for EL 4 are under study, as well as alternative concepts. The paper gives some data for a large reactor in the present state of technology, as a result from optimization studies. Technical improvements, especially in the field of materials could lead to even more interesting performances. Some prospects are mentioned for the long run. Investment costs and fuel cycles are discussed in the last part. (authors) [French] La France, qui a base son effort principal pour la production d'energie nucleaire sur la filiere des reacteurs a uranium naturel et graphite refroidis par gaz, et qui a un programme a plus

Chemical elimination of alumina in suspension in nuclear reactors heavy water

International Nuclear Information System (INIS)

Ledoux, A.

1967-02-01

Corrosion of aluminium in contact with moderating water in nuclear reactor leads to the formation of an alumina hydrosol which can have an adverse effect on the operation of the reactor. Several physical methods have been used in an attempt to counteract this effect. The method proposed here consists in the elimination of the aluminium by dissolution and subsequent fixation in the ionic form on mixed-bed ion-exchange resin. In order to do this, the parameters and the values of these parameters most favorable to the dissolution process have been determined. If the moderator is heavy water, the deuterated acid can be prepared by converting a solution in heavy water to a salt of the acid using a deuterated cationic resin. (author) [fr

Growth scenarios with thorium fuel cycles in pressurised heavy water reactors

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1991-01-01

Since India has generous deposits of thorium, the availability of thorium will not be a limiting factor in any growth scenario. It is fairly well accepted that the best system for utilisation of thorium is the heavy water reactor. The growth scenarios possible using thorium in HWRs are considered. The base has been taken as 50,000 tons of natural uranium and practically unlimited thorium. The reference reactor has been assumed to be the PHWR, and all other growth scenarios are compared with the growth scenario provided by the once-through natural cycle in the PHWR. Two reactor types have been considered: the heavy water moderated, heavy water cooled, pressure tube reactor, known as the PHWR; and the heavy water moderated and cooled pressure vessel kind, similar to the ATUCHA reactor in Argentina. For each reactor, a number of different fuel cycles have been studied. All these cycles have been based on thorium. These are: the self-sustaining equilibrium thorium cycle (SSET); the high conversion ratio high burnup cycle; and the once through thorium cycle (OTT). The cycle have been initiated in two ways: one is by starting the cycle with natural uranium, reprocessing the spent fuel to obtain plutonium, and use that plutonium to initiate the thorium cycle; the other is to enrich the uranium to about 2-3% U-235 (the so-called Low Enriched Uranium or LEU), and use the LEU to initiate the thorium cycle. Both cases have been studied, and growth scenarios have been projected for every one of the possible combinations. (author). 1 tab

Status of advanced technology and design for water cooled reactors: Heavy water reactors

International Nuclear Information System (INIS)

1989-07-01

In 1987 the IAEA established the International Working Group on Advanced Technologies for Water-Cooled Reactors (IWGATWR). Within the framework of the IWGATWR the IAEA Technical Report on Status of Advanced Technology and Design for Water Cooled Reactors, Part I: Light Water Reactors and Part II: Heavy Water Reactors, has been undertaken to document the major current activities and trends of technological improvement and development for future water reactors. Part I of the report dealing with Light Water Reactors (LWRs) was published in 1988 (IAEA-TECDOC-479). Part II of the report covers Heavy Water Reactors (HWRs) and has now been prepared. This report is based largely upon submissions from Member States. It has been supplemented by material from the presentations at the IAEA Technical Committee and Workshop on Progress in Heavy Water Reactor Design and Technology held in Montreal, Canada, December 6-9, 1988. It is hoped that this part of the report, containing the status of advanced heavy water reactor technology up to 1988 and ongoing development programmes will aid in disseminating information to Member States and in stimulating international cooperation. Refs, figs and tabs

Reactor physics measurements with 19-element ThOsub(2)-sup(235)UOsub(2) cluster fuel in heavy water moderator

International Nuclear Information System (INIS)

French, P.M.

1985-02-01

Low power lattice physics measurements have been performed with a single rod of 19-element thorium oxide fuel enriched with 1.45 wt. percent sub(235)UOsub(2) (93 percent enriched) in a simulated heavy water moderated and cooled power reactor core. The experiments were designed to provide data relevant to a power reactor irradiation and to obtain some basic information on the physics of uranium-thorium fuel material. Some theoretical flux calculations are summarized and show reasonable agreement with experiment

General description of advanced heavy water reactor

International Nuclear Information System (INIS)

Kakodkar, A.; Sinha, R.K.; Dhawan, M.L.

1999-01-01

Advanced Heavy Water Reactor is a boiling light water cooled, heavy water moderated and vertical pressure tube type reactor with its design optimised for utilisation of thorium for power generation. The core consists of (Th-U 233 )O 2 and (Th-Pu)O 2 fuel with a discharge burn up of 20,000 MWd/Te. This reactor incorporates several features to simplify the design, which eliminate certain systems and components. AHWR design is also optimised for easy replaceability of coolant channels, facilitation of in-service inspection and maintenance and ease of erection. The AHWR design also incorporates several passive systems for performing safety-related functions in the event of an accident. In case of LOCA, emergency coolant is injected through 4 accumulators of 260 m 3 capacity directly into the core. Gravity driven water pool of capacity 6000 m 3 serves to cool the core for 3 days without operator's intervention. Core submergence, passive containment isolation and passive containment cooling are the added features in AHWR. The paper describes the various process systems, core and fuel design, primary components and safety concepts of AHWR. Plant layout and technical data are also presented. The conceptual design of the reactor has been completed, and the detailed design and development is scheduled for completion in the year 2002. (author)

UK methods for studying fuel management in water moderated reactors

International Nuclear Information System (INIS)

Fayers, F.J.

1970-10-01

Current UK methods for studying fuel management and for predicting the reactor physics performance for both light and heavy water moderated power reactors are reviewed. Brief descriptions are given of the less costly computer codes used for initial assessment studies, and also the more elaborate programs associated with detailed evaluation are discussed. Some of the considerations influencing the accuracy of predictions are included with examples of various types of experimental confirmation. (author)

CFD Application and OpenFOAM on the 2-D Model for the Moderator System of Heavy-Water Reactors

International Nuclear Information System (INIS)

Chang, Se Myong; Park, A. Y.; Kim, Hyoung Tae

2011-01-01

The flow in the complex pipeline system in a calandria tank of CANDU reactor is transported through the distribution of heat sources, which also exerts the pressure drop to the coolant flow. So the phenomena should be considered as multi-physics both in the viewpoints of heat transfer and fluid dynamics. In this study, we have modeled the calandria tank system as two-dimensional simplified one preliminarily that is yet far from the real objects, but to see the essential physics and to test the possibility of the present CFD(computational fluid dynamics) methods for the thermo-hydraulic problem in the moderator system of heavy-water reactors

Outline of design, manufacturing and installation experience of pressure vessel structure for the prototype heavy water moderated boiling light water cooled reactor 'FUGEN'

International Nuclear Information System (INIS)

Shibato, Eizo; Oguchi, Isao; Kishi, Toshikazu; Kitagawa, Yuji

1977-01-01

After component installation completed in June 1977 and various functional tests to be conducted later, the prototype heavy water moderated, boiling light water cooled reactor ''FUGEN'' is scheduled to reach first criticality in March 1978. Since the pressure vessel of ''FUGEN'' is completely different from that of a light water reactor in structure and materials, through research and development work was carried out prior to fabrication and construction. Based on these studies, installation of the actual pressure vessel was completed. Functional tests are now under way. This article describes examples in which our research and development results are reflected on design, manufacture, and installation of the pressure vessel. Also it introduces noteworthy achievements relevant to production techniques in manufacture and installation. (auth.)

Heavy water and nonproliferation

International Nuclear Information System (INIS)

Miller, M.M.

1980-05-01

This report begins with a historical sketch of heavy water. The report next assesses the nonproliferation implications of the use of heavy water-moderated power reactors; several different reactor types are discussed, but the focus is on the natural uranium, on-power fueled, pressure tube reactor CANDU. The need for and development of on-power fueling safeguards is discussed. Also considered is the use of heavy water in plutonium production reactors as well as the broader issue of the relative nuclear leverage that suppliers can bring to bear on countries with natural uranium-fueled reactors as compared to those using enriched designs. The final chapter reviews heavy water production methods and analyzes the difficulties involved in implementing these on both a large and a small scale. It concludes with an overview of proprietary and nonproliferation constraints on heavy water technology transfer

Licensing assessment of the Candu Pressurized Heavy Water Reactor. Preliminary safety information document. Volume II

International Nuclear Information System (INIS)

1977-06-01

ERDA has requested United Engineers and Constructors (UE and C) to evaluate the design of the Canadian natural uranium fueled, heavy water moderated (CANDU) nuclear reactor power plant to assess its conformance with the licensing criteria and guidelines of the U.S. Nuclear Regulatory Commission (USNRC) for light water reactors. This assessment was used to identify cost significant items of nonconformance and to provide a basis for developing a detailed cost estimate for a 1140 MWe, 3-loop Pressurized Heavy Water Reactor (PHWR) located at the Middletown, USA Site

Physical particularities of nuclear reactors using heavy moderators of neutrons

Energy Technology Data Exchange (ETDEWEB)

Kulikov, G. G., E-mail: ggkulikov@mephi.ru; Shmelev, A. N. [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) (Russian Federation)

2016-12-15

In nuclear reactors, thermal neutron spectra are formed using moderators with small atomic weights. For fast reactors, inserting such moderators in the core may create problems since they efficiently decelerate the neutrons. In order to form an intermediate neutron spectrum, it is preferable to employ neutron moderators with sufficiently large atomic weights, using {sup 233}U as a fissile nuclide and {sup 232}Th and {sup 231}Pa as fertile ones. The aim of the work is to investigate the properties of heavy neutron moderators and to assess their advantages. The analysis employs the JENDL-4.0 nuclear data library and the SCALE program package for simulating the variation of fuel composition caused by irradiation in the reactor. The following main results are obtained. By using heavy moderators with small neutron moderation steps, one is able to (1) increase the rate of resonance capture, so that the amount of fertile material in the fuel may be reduced while maintaining the breeding factor of the core; (2) use the vacant space for improving the fuel-element properties by adding inert, strong, and thermally conductive materials and by implementing dispersive fuel elements in which the fissile material is self-replenished and neutron multiplication remains stable during the process of fuel burnup; and (3) employ mixtures of different fertile materials with resonance capture cross sections in order to increase the resonance-lattice density and the probability of resonance neutron capture leading to formation of fissile material. The general conclusion is that, by forming an intermediate neutron spectrum with heavy neutron moderators, one can use the fuel more efficiently and improve nuclear safety.

Physical particularities of nuclear reactors using heavy moderators of neutrons

International Nuclear Information System (INIS)

Kulikov, G. G.; Shmelev, A. N.

2016-01-01

In nuclear reactors, thermal neutron spectra are formed using moderators with small atomic weights. For fast reactors, inserting such moderators in the core may create problems since they efficiently decelerate the neutrons. In order to form an intermediate neutron spectrum, it is preferable to employ neutron moderators with sufficiently large atomic weights, using "2"3"3U as a fissile nuclide and "2"3"2Th and "2"3"1Pa as fertile ones. The aim of the work is to investigate the properties of heavy neutron moderators and to assess their advantages. The analysis employs the JENDL-4.0 nuclear data library and the SCALE program package for simulating the variation of fuel composition caused by irradiation in the reactor. The following main results are obtained. By using heavy moderators with small neutron moderation steps, one is able to (1) increase the rate of resonance capture, so that the amount of fertile material in the fuel may be reduced while maintaining the breeding factor of the core; (2) use the vacant space for improving the fuel-element properties by adding inert, strong, and thermally conductive materials and by implementing dispersive fuel elements in which the fissile material is self-replenished and neutron multiplication remains stable during the process of fuel burnup; and (3) employ mixtures of different fertile materials with resonance capture cross sections in order to increase the resonance-lattice density and the probability of resonance neutron capture leading to formation of fissile material. The general conclusion is that, by forming an intermediate neutron spectrum with heavy neutron moderators, one can use the fuel more efficiently and improve nuclear safety.

Procedure for operating a heavy water cooled power reactor

International Nuclear Information System (INIS)

Rau, P.; Kumpf, H.

1981-01-01

Nuclear reactors cooled by heavy water usually have equipment for fuel element exchange during operation, with the primary circuit remaining contained. This fuel element exchange equipment is expensive and complicated in many respects. According to the invention, the heavy water is therefore replaced by light water after a certain time of operation in such way that light water is led in and heavy water is led off. After the replacement, at least a quarter of the fuel elements of the reactor core is exchanged with the reactor pressure vessel being open. Then the light water serving as a shielding is replaced by heavy water, with the reactor pressure vessel being closed. The invention is of interest particularly for high-conversion reactors. (orig.) [de

20% inlet header break analysis of Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Srivastava, A.; Gupta, S.K.; Venkat Raj, V.; Singh, R.; Iyer, K.

2001-01-01

The proposed Advanced Heavy Water Reactor (AHWR) is a 750 MWt vertical pressure tube type boiling light water cooled and heavy water moderated reactor. A passive design feature of this reactor is that the heat removal is achieved through natural circulation of primary coolant at all power levels, with no primary coolant pumps. Loss of coolant due to failure of inlet header results in depressurization of primary heat transport (PHT) system and containment pressure rise. Depressurization activates various protective and engineered safety systems like reactor trip, isolation condenser and advanced accumulator, limiting the consequences of the event. This paper discusses the thermal hydraulic transient analysis for evaluating the safety of the reactor, following 20% inlet header break using RELAP5/MOD3.2. For the analysis, the system is discretized appropriately to simulate possible flow reversal in one of the core paths during the transient. Various modeling aspects are discussed in this paper and predictions are made for different parameters like pressure, temperature, steam quality and flow in different parts of the Primary Heat Transport (PHT) system. Flow and energy discharges into the containment are also estimated for use in containment analysis. (author)

FLUID MODERATED REACTOR

Science.gov (United States)

Wigner, E.P.; Ohlinger, L.A.; Young, G.J.; Weinberg, A.M.

1957-10-22

A reactor which utilizes fissionable fuel elements in rod form immersed in a moderator or heavy water and a means of circulating the heavy water so that it may also function as a coolant to remove the heat generated by the fission of the fuel are described. In this design, the clad fuel elements are held in vertical tubes immersed in heavy water in a tank. The water is circulated in a closed system by entering near the tops of the tubes, passing downward through the tubes over the fuel elements and out into the tank, where it is drawn off at the bottom, passed through heat exchangers to give up its heat and then returned to the tops of the tubes for recirculation.

Development of the heavy-water organic-cooled reactor. Status report from the United States of America

Energy Technology Data Exchange (ETDEWEB)

Trilling, C A [Atomics International, Division of North American Aviation, Inc., Canoga Park, CA (United States)

1967-01-01

In late 1964 the United States Atomic Energy Commission decided to undertake the development of the heavy-water-moderated nuclear power reactor as part of its overall programme for the development of advanced converter reactors. The inclusion of the heavy-water reactor concept was based on its indicated potential for achieving: efficient utilization of available fuel resources; generation of low cost electric power; feasibility of scale-up to very large single unit plant sizes for the dual purpose of generating power and desalting sea water. The excellent neutron economy inherent in heavy-water moderation allows a significant increase in the amount of power which can be generated from a given amount of ore. If one takes into account the amount of uranium required not only for burn-up but also to inventory new reactors in a rapidly expanding nuclear economy, heavy-water reactors show the potential of extracting one and a half to two times more power from the ore mined than light-water reactors. Such an improvement in dynamic fuel utilization will postpone the depletion of low cost uranium ore reserves, providing more time for the discovery of new ore resources and the development of economic fast breeder reactors. The excellent neutron economy of the heavy-water reactor also allows the achievement of appreciable burn-up with low enrichment fuel, with consequent low fuel cycle costs and therefore low energy generation costs. These low fuel cycle costs make the economics of this type of reactor rather insensitive to rising ore costs. They also make the concept well suited for the most economic production of the large quantities of heat required for water desalination. The use of individual pressure tubes for circulating the coolant through the reactor vessel lends itself to the development of a modular type design, which can be scaled up to very large single unit plant sizes by simply increasing the number of identical pressure tube modules and the number of coolant

Moderator for nuclear reactor

International Nuclear Information System (INIS)

Milgram, M.S.; Dunn, J.T.; Hart, R.S.

1995-01-01

This invention relates to a moderator for a nuclear reactor and more specifically, to a composite moderator. A moderator is designed to slow down, or thermalize, neutrons which are released during nuclear reactions in the reactor fuel. Pure or almost pure materials like light water, heavy water, beryllium or graphite are used singly as moderators at present. All these materials, are used widely. Graphite has a good mechanical strength at high temperatures encountered in the nuclear core and therefore is used as both the moderator and core structural material. It also exhibits a low neutron-capture cross section and high neutron scattering cross section. However, graphite is susceptible to attach by carbon dioxide and/or oxygen where applicable, and releases stress energy under certain circumstances, although under normal operating conditions these reactions can be controlled. (author). 1 tab

Technologies for tritium control in fission reactors moderated with heavy water

International Nuclear Information System (INIS)

Ramilo, L.B.; Gomez de Soler, S.M.

1996-01-01

This study was done within a program one of whose objectives was to analyze the possible strategies and technologies, to be applied to HWR at Argentine nuclear power plants, for tritium control. The high contribution of tritium to the total dose has given rise to the need by the operators and/or designers to carry out developments and improvements to try to optimize tritium control technologies. Within a tritium control program, only that one which includes the heavy water detritiation will allow to reduce the tritium concentrations at optimum levels for safety and cost-effective power plant operation. The technology chosen to be applied should depend not only on the technical feasibility but also on the analysis of economic and juncture factors such as, among others, the quantity of heavy water to be treated. It is the authors' belief that AECL tendency concerning heavy water treatment in its future reactors would be to employ the CECE technology complemented with immobilization on titanium beds, with the 'on-line' detritiation in each nuclear power plant. This would not be of immediate application since our analysis suggests that AECL would assume that the process is under development and needs to be tested. (author). 21 refs

Indian heavy water programme - challenges and opportunities

International Nuclear Information System (INIS)

Aruldoss Kanthiah, W.S.

2010-01-01

Discovery of fission of uranium in 1939 opened up hitherto unknown possibilities for utilising the fission energy for use of mankind, mainly for the production of and electrical energy. It was realised that this nuclear energy could be an ideal substitute for the fast depleting fossil fuels which would one day get exhausted. Two main concepts of nuclear power reactor got evolved, one enriched uranium fuelled, ordinary water moderated reactor and another natural uranium fuelled heavy water moderated reactor. The concentration of uranium 235 U needed for ordinary water moderated reactors is 3% but the naturally occurring uranium in India contains only 0.7% of 235 U. The reactors utilising natural uranium as fuel require Heavy Water as moderator. The processing of uranium ore to achieve from 0.7% to 3% is highly complex. Recognising the fact that India has limited uranium resources but rich thorium resources, Dr. Bhabha formulated a three stage nuclear power generation programme for our country. The first generation reactors can use natural uranium as fuel with heavy water as moderator. Since the technology to generate such large scale heavy water to match the urgent need for nuclear power generation was not indigenously available, the technology available with Canada and France was utilised for installation of first generation heavy water plants in India. However, the peaceful nuclear experiment conducted by India in 1974 caused resentment among the countries that supplied Heavy Water technology to India and they stopped all technological help and assistance in nuclear field. Thereafter, it was the story of India going alone in heavy water production. That made India meets successfully all challenges on the way to installation, commissioning and sustained operation of all plants. Today we have six operating Heavy Water plants, spread all over the country. We have reached a stage, a change from a situation of crunch to a level of not only self sufficiency but to a

Core Design and Deployment Strategy of Heavy Water Cooled Sustainable Thorium Reactor

Directory of Open Access Journals (Sweden)

Naoyuki Takaki

2012-08-01

Full Text Available Our previous studies on water cooled thorium breeder reactor based on matured pressurized water reactor (PWR plant technology concluded that reduced moderated core by arranging fuel pins in a triangular tight lattice array and using heavy water as coolant is appropriate for achieving better breeding performance and higher burn-up simultaneously [1–6]. One optimum core that produces 3.5 GW thermal energy using Th-²³³U oxide fuel shows a breeding ratio of 1.07 and averaged burn-up of about 80 GWd/t with long cycle length of 1300 days. The moderator to fuel volume ratio is 0.6 and required enrichment of ²³³U for the fresh fuel is about 7%. The coolant reactivity coefficient is negative during all cycles despite it being a large scale breeder reactor. In order to introduce this sustainable thorium reactor, three-step deployment scenario, with intermediate transition phase between current light water reactor (LWR phase and future sustainer phase, is proposed. Both in transition phase and sustainer phase, almost the same core design can be applicable only by changing fissile materials mixed with thorium from plutonium to ²³³U with slight modification in the fuel assembly design. Assuming total capacity of 60 GWe in current LWR phase and reprocessing capacity of 800 ton/y with further extensions to 1600 ton/y, all LWRs will be replaced by heavy water cooled thorium reactors within about one century then thorium reactors will be kept operational owing to its potential to sustain fissile fuels while reprocessing all spent fuels until exhaustion of massive thorium resource.

Conceptual design of a pressure tube light water reactor with variable moderator control

International Nuclear Information System (INIS)

Rachamin, R.; Fridman, E.; Galperin, A.

2012-01-01

This paper presents the development of innovative pressure tube light water reactor with variable moderator control. The core layout is derived from a CANDU line of reactors in general, and advanced ACR-1000 design in particular. It should be stressed however, that while some of the ACR-1000 mechanical design features are adopted, the core design basics of the reactor proposed here are completely different. First, the inter fuel channels spacing, surrounded by the calandria tank, contains a low pressure gas instead of heavy water moderator. Second, the fuel channel design features an additional/external tube (designated as moderator tube) connected to a separate moderator management system. The moderator management system is design to vary the moderator tube content from 'dry' (gas) to 'flooded' (light water filled). The dynamic variation of the moderator is a unique and very important feature of the proposed design. The moderator variation allows an implementation of the 'breed and burn' mode of operation. The 'breed and burn' mode of operation is implemented by keeping the moderator tube empty ('dry' filled with gas) during the breed part of the fuel depletion and subsequently introducing the moderator by 'flooding' the moderator tube for the 'burn' part. This paper assesses the conceptual feasibility of the proposed concept from a neutronics point of view. (authors)

Application of the dose limitation system to the control of carbon-14 releases from heavy-water-moderated reactors

International Nuclear Information System (INIS)

Beninson, D.; Gonzalez, A.J.

1982-01-01

Heavy-water-moderated reactors produce substantially more carbon-14 than light-water reactors. Applying the principles of the systems of dose limitation, the paper presents the rationale used for establishing the release limit for effluents containing this nuclide and for the decisions made regarding the effluent treatment in the third nuclear power station in Argentina. Production of carbon-14 in PHWR and the release routes are analysed in the light of the different effluent treatment possibilities. An optimization assessment is presented, taking into account effluent treatment and waste management costs, and the collective effective dose commitment due to the releases. The contribution of present carbon-14 releases to future individual doses is also analysed in the light of an upper bound for the contribution, representing a fraction of the individual dose limits. The paper presents the resulting requirements for the effluent treatment regarding carbon-14 and the corresponding regulatory aspects used in Argentina. (author)

A Management Strategy for the Heavy Water Reflector Cooling System of HANARO Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Jung, H. S.; Park, Y. C.; Lim, S. P. (and others)

2007-11-15

Heavy water is used as the reflector and the moderator of the HANARO research reactor. After over 10 years operation since first criticality in 1995 there arose some operational issues related with the tritium. A task force team(TFT) has been operated for 1 year since September 2006 to study and deduce resolutions of the issues concerning the tritium and the degradation of heavy water in the HANARO reflector system. The TFT drew many recommendations on the hardware upgrade, tritium containing air control, heavy water quality management, waste management, and tritium measurement system upgrade.

Role of passive valves & devices in poison injection system of advanced heavy water reactor

International Nuclear Information System (INIS)

Sapra, M.K.; Kundu, S.; Vijayan, P.K.; Vaze, K.K.; Sinha, R.K.

2014-01-01

The Advanced Heavy Water Reactor (AHWR) is a 300 MWe pressure tube type boiling light water (H 2 O) cooled, heavy water (D 2 O) moderated reactor. The reactor design is based on well-proven water reactor technologies and incorporates a number of passive safety features such as natural circulation core cooling; direct in-bundle injection of light water coolant during a Loss of Coolant Accident (LOCA) from Advanced Accumulators and Gravity Driven Water Pool by passive means; Passive Decay Heat Removal using Isolation Condensers, Passive Containment Cooling System and Passive Containment Isolation System. In addition to above, there is another passive safety system named as Passive Poison Injection System (PPIS) which is capable of shutting down the reactor for a prolonged time. It is an additional safety system in AHWR to fulfill the shutdown function in the event of failure of wired shutdown systems i.e. primary and secondary shut down systems of the reactor. When demanded, PPIS injects the liquid poison into the moderator by passive means using passive valves and devices. On increase of main heat transport (MHT) system pressure beyond a predetermined value, a set of rupture disks burst, which in-turn actuate the passive valve. The opening of passive valve initiates inrush of high pressure helium gas into poison tanks to push the poison into the moderator system, thereby shutting down the reactor. This paper primarily deals with design and development of Passive Poison Injection System (PPIS) and its passive valves & devices. Recently, a prototype DN 65 size Poison Injection Passive Valve (PIPV) has been developed for AHWR usage and tested rigorously under simulated conditions. The paper will highlight the role of passive valves & devices in PPIS of AHWR. The design concept and test results of passive valves along with rupture disk performance will also be covered. (author)

Heavy water upgrader of 'Fugen'

International Nuclear Information System (INIS)

Matsushita, Tadashi; Sasaki, Shigeo

1980-01-01

The nuclear power station of the advanced thermal prototype reactor ''Fugen'' has continued the smooth operation since it started the fullscale operation in March, 1979. Fugen is the first heavy water-moderated, boiling light water-cooled reactor in Japan, and its outstanding feature is the use of heavy water as the moderator. The quantity of heavy water retained in Fugen is about 140 m 3 , and the concentration is 99.8 wt.%. This heavy water had been made is USA, and was imported from F.R. of Germany where it had been used. Heavy water is an internationally regulated material, and it is very expensive and hard to purchase. Therefore in order to prevent the deterioration of heavy water and to avoid its loss as far as possible, the management of the quantity and the control of the water quality have been carried out carefully and strictly. The generation of deteriorated heavy water occurs from the exchange of ion exchange resin for poison removal and purification. The heavy water upgrader reconcentrates the deteriorated heavy water of high concentration and returns to the heavy water system, and it was installed for the purpose of reducing the purchase of supplementary heavy water. The outline of the heavy water upgrader, its construction, the performance test and the operation are described. (Kako, I.)

Advanced electrolytic cascade process for tritium recovery from irradiated heavy water moderator (Preprint No. PD-15)

International Nuclear Information System (INIS)

Ragunathan, P.; Mitra, S.K.; Jain, D.K.; Nayar, M.G.; Ramani, M.P.S.

1989-04-01

The paper briefly describes a design study of an electrolytic cascade process plant for enrichment and recovery of tritium from irradiated heavy water moderators from Rajasthan Atomic Power Station Reactors. In direct multistage electrolysis process, tritiated heavy water from the reactor units is fed to the electrolytic cell modules arranged in the form of a cascade where it is enriched and decomposed into O 2 gas stream and D 2 /DT gas stream. The direct electrolysis of tritiated heavy water allows tritium to be concentrated in the aqueous phase. Several stages are used to achieve the necessary enrichment. The cascade plant incorporates the advanced electrolyser technology developed in Bhabha Atomic Research Centre (Bombay) using porous nickel electrodes, capable o f high current density operation at reduced energy consumption for electrolysis. (author). 3 tabs

Drying of heavy water system and works of charging heavy water in Fugen

International Nuclear Information System (INIS)

Matsushita, Tadashi; Iijima, Setsuo

1980-01-01

The advanced thermal reactor ''Fugen'' is the first heavy water-moderated, boiling light water-cooled nuclear reactor for power generation in Japan. It is a large heavy water reactor having about 130 m 3 of heavy water inventory and about 300 m 3 of helium space as the cover gas of the heavy water system. The heavy water required was purchased from FRG, which had been used for the power output test in the KKN, and the quality was 99.82 mol % mean heavy water concentration. The concentration of heavy water for Fugen used for the nuclear design is 99.70 mol%, and it was investigated how heavy water can be charged without lowering the concentration. The matters of investigation include the method of bringing the heavy water and helium system to perfect dryness after washing and light water test, the method of confirming the sufficient dryness to prevent the deterioration, and the method of charging heavy water safely from its containers. On the basis of the results of investigation, the actual works were started. The works of drying the heavy water and helium system by vacuum drying, the works of sampling heavy water and the result of the degree of deterioration, and the works of charging heavy water and the measures to the heavy water remaing in the containers are described. All the works were completed safely and smoothly. (J.P.N.)

Heat exchangers in heavy water reactor systems

International Nuclear Information System (INIS)

Mehta, S.K.

1988-01-01

Important features of some major heat exchange components of pressurized heavy water reactors and DHRUVA research reactor are presented. Design considerations and nuclear service classifications are discussed

Breeding capability and void reactivity analysis of heavy-water-cooled thorium reactor

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2008-01-01

The fuel breeding and void reactivity coefficient of thorium reactors have been investigated using heavy water as coolant for several parametric surveys on moderator-to-fuel ratio (MFR) and burnup. The equilibrium fuel cycle burnup calculation has been performed, which is coupled with the cell calculation for this evaluation. The η of 233 U shows its superiority over other fissile nuclides in the surveyed MFR ranges and always stays higher than 2.1, which indicates that the reactor has a breeding condition for a wide range of MFR. A breeding condition with a burnup comparable to that of a standard PWR or higher can be achieved by adopting a larger pin gap (1-6 mm), and a pin gap of about 2 mm can be used to achieve a breeding ratio (BR) of 1.1. A feasible design region of the reactors, which fulfills the breeding condition and negative void reactivity coefficient, has been found. A heavy-water-cooled PWR-type Th- 233 U fuel reactor can be designed as a breeder reactor with negative void coefficient. (author)

General design and main problems of a gas-heavy-water power reactor contained in a pressure vessel

International Nuclear Information System (INIS)

Roche, R.; Gaudez, J.C.

1964-01-01

In the framework of research carried out on a CO 2 -cooled power reactor moderated by heavy water, the so-called 'pressure vessel' solution involves the total integration of the core, of the primary circuit (exchanges and blowers) and of the fuel handling machine inside a single, strong, sealed vessel made of pre-stressed concrete. A vertical design has been chosen: the handling 'attic' is placed above the core, the exchanges being underneath. This solution makes it possible to standardize the type of reactor which is moderated by heavy-water or graphite and cooled by a downward stream of carbon dioxide gas; it has certain advantages and disadvantages with respect to the pressure tube solution and these are considered in detail in this report. Extrapolation presents in particular.problems due specifically to the heavy water (for example its cooling,its purification, the balancing of the pressures of the heavy water and of the gas, the assembling of the internal structures, the height of the attic, etc. (authors) [fr

High converter pressurized water reactor with heavy water as a coolant

International Nuclear Information System (INIS)

Ronen, Y.; Reyev, D.

1983-01-01

There is an increasing interest in water breeder and high converter reactors. The increase in the conversion ratio of these reactors is obtained by hardening the neutron spectrum achieved by tightening the reactor's lattice. Another way of hardening the neutron spectrum is to replace the light water with heavy water. Two pressurized water reactor fuel cycles that use heavy water as a coolant are considered. The first fuel cycle is based on plutonium and depleted uranium, and the second cycle is based on plutonium and enriched uranium. The uranium ore and separative work unit (SWU) requirements are calculated as well as the fuel cycle cost. The savings in uranium ore are about40 and 60% and about40% in SWU for both fuel cycles considered

Plutonium Recycle Test Reactor (PRTR). Operating Experience and Supporting R and D, Its Application to Heavy-Water Power Reactor Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Harty, H. [Battelle Memorial Institute, Pacific Northwest Laboratories, Richland, WA (United States)

1968-04-15

Convincing answers to questions about heavy-water, pressure-tube, power reactors, e.g. pressure-tube serviceability, heavy-water management problems, long-term behaviour of special pressure-tube reactor components, and unique operating maintenance problems (compared to light-water reactors) must be based on actual operating experience with that type of reactor. PRTR operating experience and supporting R and D studies, although not always simple extrapolations to power reactors, can be summarized in a context applicable to future heavy-water power reactors, as follows: 1. Pressure-tube life, in a practical case, need not be limited by creep, gross hydriding, corrosion, or mechanical damage. The possibility that growth of a defect (perhaps service-induced) to a size that is critical under certain operating conditions, remains a primary unknown in pressure- tube life extrapolations. A pressure-tube failure in PRTR (combined with gross release of fuel material) proved only slightly more inconvenient, time consuming, and damaging to the reactor proper, than occurred with a gross failure of a fuel element in PRTR. 2. Routine operating losses of heavy water appear tractable in heavy-water-cooled power reactors; losses from low-pressure systems can be insignificant over the life of a plant. Non-routine losses may prove to be the largest component of loss over the life of a plant. 3. The performance of special components in PRTR, e.g. the calandria and shields, has not deteriorated despite being subjected to non-standard operating conditions. The calandria now contains a light-water reflector with single barrier separation from the heavy-water moderator. The carbon steel shields (containing carbon steel shot) show no deterioration based on pressure drop measurements and piping activation immediately outside the shields. The helium pressurization system (for primary coolant pressurization) remains a high maintenance system, and cannot be recommended for power reactors, based

Light and heavy water replacing system in reactor container

International Nuclear Information System (INIS)

Miyamoto, Keiji.

1979-01-01

Purpose: To enable to determine the strength of a reactor container while neglecting the outer atmospheric pressure upon evacuation, by evacuating the gap between the reactor container and a biological thermal shield, as well as the container simultaneously upon light water - heavy water replacement. Method: Upon replacing light water with heavy water by vacuum evaporation system in a nuclear reactor having a biological thermal shield surrounding the reactor container incorporating therein a reactor core by way of a heat expansion absorbing gap, the reactor container and the havy water recycling system, as well as the inside of heat expansion absorbing gap are evacuated simultaneously. This enables to neglect the outer atmospheric outer pressure upon evacuation in the determination of the container strength, and the thickness of the container can be decreased by so much as the external pressure neglected. (Moriyama, K.)

Research on Reduced-Moderation Water Reactor (RMWR)

International Nuclear Information System (INIS)

Iwamura, Takamichi; Okubo, Tsutomu; Shimada, Shoichiro

1999-11-01

The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor which aims at effective utilization of uranium resource, high burn-up and long operation cycle, and plutonium multi-recycle. These characteristics can be achieved by the high conversion ratio from 238 U to 239 Pu resulted from the higher neutron energy spectrum in comparison to conventional light water reactors. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPCO) in 1998. In the core design study of the RMWR, negative void reactivity coefficient is required from a viewpoint of safety as well as establishing hard neutron spectrum. In order to achieve the above trade-off characteristics simultaneously, several basic core design ideas should be combined, such as a tight lattice fuel assembly, a flat core, a blanket effect, a streaming effect and so on. Up to now, five core concepts have been created for the RMWR as follows: a high conversion BWR with high void fraction and super-flat core, a long operation cycle BWR using void channels, a high conversion BWR without blankets, a high conversion PWR using heavy water as a coolant, and a PWR for plutonium multi-recycle using seed-blanket type fuel assemblies. The present report summarizes the objectives, domestic and international trends, principles and characteristics, core conceptual designs and future R and D plans of the RMWR. (J.P.N.)

Research on Reduced-Moderation Water Reactor (RMWR)

Energy Technology Data Exchange (ETDEWEB)

Iwamura, Takamichi; Okubo, Tsutomu; Shimada, Shoichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

1999-11-01

The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor which aims at effective utilization of uranium resource, high burn-up and long operation cycle, and plutonium multi-recycle. These characteristics can be achieved by the high conversion ratio from {sup 238}U to {sup 239}Pu resulted from the higher neutron energy spectrum in comparison to conventional light water reactors. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPCO) in 1998. In the core design study of the RMWR, negative void reactivity coefficient is required from a viewpoint of safety as well as establishing hard neutron spectrum. In order to achieve the above trade-off characteristics simultaneously, several basic core design ideas should be combined, such as a tight lattice fuel assembly, a flat core, a blanket effect, a streaming effect and so on. Up to now, five core concepts have been created for the RMWR as follows: a high conversion BWR with high void fraction and super-flat core, a long operation cycle BWR using void channels, a high conversion BWR without blankets, a high conversion PWR using heavy water as a coolant, and a PWR for plutonium multi-recycle using seed-blanket type fuel assemblies. The present report summarizes the objectives, domestic and international trends, principles and characteristics, core conceptual designs and future R and D plans of the RMWR. (J.P.N.)

Neutronic calculations in heavy water moderated multiplying media using GGC-3 library nuclear data

International Nuclear Information System (INIS)

Boado, H.J.; Gho, C.J.; Abbate, M.J.

1981-01-01

Differences in obtaining transference matrices between GGC-3 code and the system to produce multigroup cross sections using GGC-3 library, recently implemented at the Neutrons and Reactors Division, have been analized. Neutronic calculations in multiplicative systems containing heavy water have been made using both methods. From the obtained results, it is concluded that the new method is more appropriate to deal with systems including moderators other than light water. (author) [es

The future 700 MWe pressurized heavy water reactor

International Nuclear Information System (INIS)

Bhardwaj, S.A.

2006-01-01

The design of a 700 MWe pressurized heavy water reactor has been developed. The design is based on the twin 540 MWe reactors at Tarapur of which the first unit has been made critical in less than 5 years from construction commencement. In the 700 MWe design boiling of the coolant, to a limited extent, has been allowed near the channel exit. While making the plant layout more compact, emphasis has been on constructability. Saving in capital cost of about 15%, over the present units, is expected. The paper describes salient design features of 700 MWe pressurized heavy water reactor

Conceptual design of a large heavy water reactor for US siting

International Nuclear Information System (INIS)

Shapiro, N.L.; Jesick, J.F.

1979-09-01

Information is presented concerning fuel management and safety and licensing assessment of the pressurized heavy water reactor; and commercial introduction of the pressurized heavy water reactor in the United States

Operating performance of the prototype heavy water reactor Fugen

International Nuclear Information System (INIS)

1984-01-01

Since the full scale operation was started in March, 1979, the ATR Fugen power station has been verifying the performance and reliability of the machinery and equipment, uranium-plutonium mixed oxide fuel and so on, and obtaining the technical prospect for putting ATRs in practical use by accumulating operation and maintenance techniques, through about five years of operation. In this report, the operational results of the Fugen power station are described. Fugen is a heavy water-moderated, boiling light water-cooled, pressure tube type reactor with 165 MWe output. As of the end of March, 1984, the total generated electric power was about 4.3 billion kWh, and the operation time was about 27,000 hours. The mean capacity ratio reached 58.8%. During the operation period, troubles including plant shutdown occurred eight times, but generally the performance and reliability of the machinery and equipment have been good. 580 fuels including 284 MOX fuels have been charged, but fuel breaking did not occur at all. The consumption of heavy water and the leak of tritium did not cause problem. The management of the core and fuel, the management of maintenance, the quality control of cooling water and heavy water, radiation control and the management of wastes are reported. (Kako, I.)

Operation management of the prototype heavy water reactor 'Fugen'

International Nuclear Information System (INIS)

Muramatsu, Akira; Takei, Hiroaki; Iwanaga, Shigeru; Noda, Masao; Hara, Hidemi

1983-01-01

The advanced thermal reactor Fugen power station has continued almost smooth operation since it began the full scale operation as the first homemade power reactor in Japan in March, 1979. In the initial period of operation, some troubles were experienced, but now, it can be said that the operational techniques of heavy water-moderated, boiling light water-cooled, pressure tube type reactors have been established, through the improvement of the operational method and equipment, and the operational experience. Also, the verification of the operational ability, maintainability, reliability and safety of this new type reactor, that is the mission of the prototype reactor, achieved steadily the good results. Hereafter, the verification of operational performance is the main objective because it is required for the design, construction and operation of the demonstration reactor. The organization for the operation management and operation, the communication at the time of the abnormality, the operation of the plant, that is, start up, stop and the operation at the rated output, the works during plant stoppage, the operation at the time of the plant abnormality, the operation of waste treatment facility and others, the improvement of the operational method, and the education and training of operators are reported. (Kako, I.)

Considerations regarding design of ion exchange columns for applications in heavy water nuclear reactors- a comprehensive review

International Nuclear Information System (INIS)

Joginder Kumar; Nema, M.K.

2000-01-01

In nuclear reactor applications the principal role of the purification system is to maintain a satisfactory chemistry of moderator and coolant which are different at various stages of reactor operations e.g. during reactor start up, for removal of neutron poison from the moderator, the purification flows are much different compared to steady state operation of the reactor. In order to cater to varying requirements regarding purification load, optimisation in connection with ion exchange column design plays an important role and becomes very challenging in Heavy Water Nuclear Reactors mainly due to the fact that heavy water is very very expensive. In this paper a comprehensive review is made for various designs adopted so far regarding IX column in Indian PHWRs of 220 MWe size for normal operations. Design and operating experience regarding large size IX column used for occasional needs during dilute chemical decontamination of 220 MWe PHWRs is also discussed. The experience regarding development testing of the proposed design of ion exchange column for 500 MWe PHWRs is also discussed

Conceptual design of a quasi-homogeneous pressurized heavy water reactor to be operated in the closed Th-U233 fuel cycle

International Nuclear Information System (INIS)

1979-06-01

This paper deals with the heavy water reactor, which, from the neutron economy point of view, offers advantages over the light water reactor. Its capability to be fuelled with natural uranium has also been considered a desirable nuclear option by various countries with sufficient domestic uranium resources not wishing to be dependent on the import of enrichment and other fuel cycle services which, in addition, would draw on the foreign exchange reserves. Pressurized heavy water reactors have been designed and built according to two somewhat different versions. While the Canadian CANDU-PHWR concept uses pressure tubes in a nearly unpressurized moderator tank (calandria), the German development line takes advantage of the established and well proven LWR technology, and, thus, uses a pressure vessel design where coolant channels and the surrounding moderator are held at equal pressure. This pressure vessel type heavy water reactor which has been built on a commercial demonstration plant level at ATUCHA in Argentina is described in a companion paper where also a conceptual design for a 685 MWsub(e) PHWR is discussed

A case study for INPRO methodology based on Indian advanced heavy water reactor

International Nuclear Information System (INIS)

Anantharaman, K.; Saha, D.; Sinha, R.K.

2004-01-01

Under Phase 1A of the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) a methodology (INPRO methodology) has been developed which can be used to evaluate a given energy system or a component of such a system on a national and/or global basis. The INPRO study can be used for assessing the potential of the innovative reactor in terms of economics, sustainability and environment, safety, waste management, proliferation resistance and cross cutting issues. India, a participant in INPRO program, is engaged in a case study applying INPRO methodology based on Advanced Heavy Water Reactor (AHWR). AHWR is a 300 MWe, boiling light water cooled, heavy water moderated and vertical pressure tube type reactor. Thorium utilization is very essential for Indian nuclear power program considering the indigenous resource availability. The AHWR is designed to produce most of its power from thorium, aided by a small input of plutonium-based fuel. The features of AHWR are described in the paper. The case study covers the fuel cycle, to be followed in the near future, for AHWR. The paper deals with initial observations of the case study with regard to fuel cycle issues. (authors)

Reactivity requirements and safety systems for heavy water reactors

International Nuclear Information System (INIS)

Kati, S.L.; Rustagi, R.S.

1977-01-01

The natural uranium fuelled pressurised heavy water reactors are currently being installed in India. In the design of nuclear reactors, adequate attention has to be given to the safety systems. In recent years, several design modifications having bearing on safety, in the reactor processes, protective and containment systems have been made. These have resulted either from new trends in safety and reliability standards or as a result of feed-back from operating reactors of this type. The significant areas of modifications that have been introduced in the design of Indian PHWR's are: sophisticated theoretical modelling of reactor accidents, reactivity control, two independent fast acting systems, full double containment and improved post-accident depressurisation and building clean-up. This paper brings out the evolution of design of safety systems for heavy water reactors. A short review of safety systems which have been used in different heavy water reactors, of varying sizes, has been made. In particular, the safety systems selected for the latest 235 MWe twin reactor unit station in Narora, in Northern India, have been discussed in detail. Research and Development efforts made in this connection are discussed. The experience of design and operation of the systems in Rajasthan and Kalpakkam reactors has also been outlined

Study on characteristics for different moderation ratios of heavy water coolant with different reactor types in equilibrium states

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2005-01-01

Several characteristics for different moderation ratios of heavy water coolant with different reactor types in equilibrium states have been investigated. Performances of PWR and CANDU reactors are compared. A calculation method for determining the required uranium enrichment for criticality of the systems has been developed by coupling the equilibrium fuel cycle burn-up calculation and cell calculation of PIJ module of SRAC2000 code. In the present study, we have compared the characteristics for different moderator to fuel ratio (MFR, 0.1 to 30), different burn-up for CANDU type and four fuels cycle schemes. Nuclide density of 235 U at MFR=1.9 decreases with increasing number of confined HM, while 235 U at higher MFR has the opposite trend. However, the nuclide density of fissile material at higher MFR is lower except 238 U. CANDU type requires lower uranium enrichment and obtains higher conversion ratio than PWR type. Lowest burn-up requires the lowest uranium enrichment and obtains the highest conversion ratio. The breeding condition can be obtained for plutonium recycle cases at MFR=2.1 of Case 4 and MFR=1.4 of Case 3. The natural uranium can be achieved at MFR=14 of plutonium recycle cases, and it can be used easier by increasing number of confined HM. (author)

Method of controlling power of a heavy water reactor

International Nuclear Information System (INIS)

Masuda, Hiroyuki.

1975-01-01

Object: To adjust a level of heavy water in a region of reflection body to control power in a heavy water reactor. Structure: The interior of a core tank filled with heavy water is divided by a partition into a core heavy water region and a reflection body region formed by surrounding the core heavy water region, and a level of heavy water within the reflection body region is adjusted to control power. Preferably, it is desirable to communicate the core heavy water region with the reflection body heavy water region at their lower portion, and gas pressure applied to an upper portion within at least one of said regions is adjusted to adjust the level of heavy water within the reflection body heavy water region. Thereby, the heavy water within the reflection body heavy water region may be introduced into the core region, thus requiring no tank which stores heavy water within the reflection body region. (Kamimura, M.)

Accident analysis of heavy water cooled thorium breeder reactor

International Nuclear Information System (INIS)

Yulianti, Yanti; Su’ud, Zaki; Takaki, Naoyuki

2015-01-01

Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

Accident analysis of heavy water cooled thorium breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Yulianti, Yanti [Department of Physics, University of Lampung Jl. Sumantri Brojonegoro No.1 Bandar Lampung, Indonesia Email: y-yanti@unila.ac.id (Indonesia); Su’ud, Zaki [Department of Physics, Bandung Institute of Technology Jl. Ganesha 10 Bandung, Indonesia Email: szaki@fi.itb.ac.id (Indonesia); Takaki, Naoyuki [Department of Nuclear Safety Engineering Cooperative Major in Nuclear Energy (Graduate School) 1-28-1 Tamazutsumi,Setagayaku, Tokyo158-8557, Japan Email: ntakaki@tcu.ac.jp (Japan)

2015-04-16

Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

LIGHT WATER MODERATED NEUTRONIC REACTOR

Science.gov (United States)

Christy, R.F.; Weinberg, A.M.

1957-09-17

A uranium fuel reactor designed to utilize light water as a moderator is described. The reactor core is in a tank at the bottom of a substantially cylindrical cross-section pit, the core being supported by an apertured grid member and comprised of hexagonal tubes each containing a pluralily of fuel rods held in a geometrical arrangement between end caps of the tubes. The end caps are apertured to permit passage of the coolant water through the tubes and the fuel elements are aluminum clad to prevent corrosion. The tubes are hexagonally arranged in the center of the tank providing an amulus between the core and tank wall which is filled with water to serve as a reflector. In use, the entire pit and tank are filled with water in which is circulated during operation by coming in at the bottom of the tank, passing upwardly through the grid member and fuel tubes and carried off near the top of the pit, thereby picking up the heat generated by the fuel elements during the fission thereof. With this particular design the light water coolant can also be used as the moderator when the uranium is enriched by fissionable isotope to an abundance of U/sup 235/ between 0.78% and 2%.

Start-up test of the prototype heavy water reactor 'FUGEN', (1)

International Nuclear Information System (INIS)

Ando, Hideki; Kawahara, Toshio

1982-01-01

The advanced thermal prototype reactor ''Fugen'' is a heavy water-moderated, boiling light water-cooled power reactor with electric output of 165 MW, which has been developed since 1966 as a national project. The start-up test was begun in March, 1978, being scheduled for about one year, and in March, 1979, it passed the final pre-use inspection and began the full scale operation. In this paper, the result of the start-up test of Fugen is reported. From the experience of the start-up test of Fugen, the following matters are important for the execution of start-up test. 1) Exact testing plan and work schedule, 2) the organization to perform the test, 3) the rapid evaluation of test results and the reflection to next testing plan, and 4) the reflection of test results to rated operation, regular inspection and so on. In the testing plan, the core characteristics peculiar to Fugen, and the features of heavy water-helium system, control system and other equipment were added to the contents of the start-up test of BWRs. The items of the start-up test were reactor physics test, plant equipment performance test, plant dynamic characteristic test, chemical and radiation measurement, and combined test. The organization to perform the start-up test, and the progress and the results of the test are reported. (Kako, I.)

Neutron moderation in heavy water

International Nuclear Information System (INIS)

Assis, J.T. de.

1980-03-01

The calculation of the energetic spectrum of thermic neutrons in heavy water, according to the models of the differential cross section; is presented. Simplifications in the Butler model are suggested for the diminution of computer time. The results obtained are compared with experimental data and with the Brown - St.John model. This calculation has been done in 30 energy groups and within our limit of precision, the results with the models and simplifications present satisfactory values, allowing its inclusion in reactor codes. (Author) [pt

Moderator behaviour and reactor internals integrity at Atucha I NPP

International Nuclear Information System (INIS)

Berra, S.; Guala, M.; Herzovich, P.; Chocron, M.; Lorenzo, A.; Raffo Calderon, Ma. C. del; Urrutia, G.

1996-01-01

Atucha I is a Pressure Vessel Heavy Water Cooled Heavy Water Moderator Reactor. In this kind of reactor the moderator tank is physically connected to the primary coolant. Since neutron economy requires the moderator to be as cold as possible, it is necessary that even when physically connected, it should have a separated cooling system, which in this case is also used as a feed-water preheater, and also heat mass transfer with primary coolant should be minimized. This condition requires that some reactor internals are designed in principle to last the whole life of the plant. However, in 1988 the failure of one internal produced a 16 month shut down. This incident could have been prevented but the idea that reactor internals would not have failures due to aging was dominant at that time avoiding the early detection of the failure. However, the analysis of the records after the incident showed that some process variables had changed previously to the incident, i.e., power exchanged at the moderator heat exchanger had increased. Since the station restart up some changes in the moderator process variables and a flow rate reduction of about 10% through the primary side of one moderator cooler were observed. In order to understand the flow reduction and the overall behaviour of moderators parameters, two models were developed that predict moderator and moderator cooler behavior under the new conditions. The present paper refers to these models, which together with the improvement of process variables measurements mentioned in another paper presented at this meeting permits to understand current moderator behaviour and helps to early diagnostic of an eventual reactor internal failure. (author). 2 refs, 4 figs, 1 tab

Moderator behaviour and reactor internals integrity at Atucha I NPP

Energy Technology Data Exchange (ETDEWEB)

Berra, S; Guala, M; Herzovich, P [Central Nuclear Atucha I, Nucleoelectrica Argentina, Lima, Buenos Aires (Argentina); Chocron, M; Lorenzo, A; Raffo Calderon, Ma. C. del; Urrutia, G [Comision Nacional de Energia Atomica, Buenos Aires (Argentina). Centro Atomico Constituyentes

1997-12-31

Atucha I is a Pressure Vessel Heavy Water Cooled Heavy Water Moderator Reactor. In this kind of reactor the moderator tank is physically connected to the primary coolant. Since neutron economy requires the moderator to be as cold as possible, it is necessary that even when physically connected, it should have a separated cooling system, which in this case is also used as a feed-water preheater, and also heat mass transfer with primary coolant should be minimized. This condition requires that some reactor internals are designed in principle to last the whole life of the plant. However, in 1988 the failure of one internal produced a 16 month shut down. This incident could have been prevented but the idea that reactor internals would not have failures due to aging was dominant at that time avoiding the early detection of the failure. However, the analysis of the records after the incident showed that some process variables had changed previously to the incident, i.e., power exchanged at the moderator heat exchanger had increased. Since the station restart up some changes in the moderator process variables and a flow rate reduction of about 10% through the primary side of one moderator cooler were observed. In order to understand the flow reduction and the overall behaviour of moderators parameters, two models were developed that predict moderator and moderator cooler behavior under the new conditions. The present paper refers to these models, which together with the improvement of process variables measurements mentioned in another paper presented at this meeting permits to understand current moderator behaviour and helps to early diagnostic of an eventual reactor internal failure. (author). 2 refs, 4 figs, 1 tab.

Detection of gaseous heavy water leakage points in CANDU 6 pressurized heavy water reactors

International Nuclear Information System (INIS)

Park, T-K.; Jung, S-H.

1996-01-01

During reactor operation, the heavy water filled primary coolant system in a CANDU 6 Pressurized Heavy Water (PHWR) may leak through routine operations of the plant via components, mechanical joints, and during inadvertent operations etc. Early detection of leak points is therefore important to maintain plant safety and economy. There are many independent systems to monitor and recover heavy water leakage in a CANDU 6 PHWR. Methodology for early detection based on operating experience from these systems, is investigated in this paper. In addition, the four symptoms of D 2 O leakage, the associated process for clarifying and verifying the leakage, and the probable points of leakage are discussed. (author)

The key design features of the Indian advanced heavy water reactor

International Nuclear Information System (INIS)

Sinha, R.K.; Kakodkar, A.; Anand, A.K.; Venkat Raj, V.; Balakrishnan, K.

1999-01-01

The 235 MWe Indian Advanced Heavy Water Reactor (AHWR) is a vertical, pressure tube type, boiling light water cooled reactor. The three key specific features of design of the AHWR, having a large impact on its viability, safety and economics, relate to its reactor physics, coolant channel, and passive safety features. The reactor physics design is tuned for maximising use of thorium based fuel, and achieving a slightly negative void coefficient of reactivity. The fulfilment of these requirements has been possible through use of PuO 2 -ThO 2 MOX, and ThO 2 -U 233 O 2 MOX in different pins of the same fuel cluster, and use of a heterogeneous moderator consisting of pyrolytic carbon and heavy water in 80%-20% volume ratio. The coolant channels of AHWR are designed for easy replaceability of pressure tubes, during normal maintenance shutdowns. The removal of pressure tube along with bottom end-fitting, using rolled joint detachment technology, can be done in AHWR coolant channels without disturbing the top end-fitting, tail pipe and feeder connections, and all other appendages of the coolant channel. The AHWR incorporates several passive safety features. These include core heat removal through natural circulation, direct injection of Emergency Core Coolant System (ECCS) water in fuel, passive systems for containment cooling and isolation, and availability of a large inventory of borated water in overhead Gravity Driven Water Pool (GDWP) to facilitate sustenance of core decay heat removal, ECCS injection, and containment cooling for three days without invoking any active systems or operator action. Incorporation of these features has been done together with considerable design simplifications, and elimination of several reactor grade equipment. A rigorous evaluation of feasibility of AHWR design concept has been completed. The economy enhancing aspects of its key design features are expected to compensate for relative complexity of the thorium fuel cycle activities

Decontamination of the RA reactor heavy water system, Annex 9

International Nuclear Information System (INIS)

Maksimovic, Z.B.; Nikolic, R.M.; Marinkovic, M.D.; Jelic, Lj.M.

1963-01-01

Both stainless steel and aluminium parts of the RA reactor heavy water system system were decontaminated as well as the heavy water itself. System was contaminated with 60 Co. Decontamination factor was determined by activity measurements during distillation. Concentration of the corrosion products in the heavy water was measured by spectrochemical analysis, and found to be 0.1 - 1 mg/l. Chemical analyses of the aluminium and stainless steel surfaces showed that cobalt was adsorbed on the aluminium oxide layer. Water solution of 7%H 3 PO 4 + 2% CrO 3 was used for decontamination of the heavy water system and distillation device. This was found to be the most efficient solvent which does not affect stainless steel corrosion. Decontamination factors achieved were from 60 - 100. Decontamination results enabled determining the distribution of cobalt in the system: 10 Ci on the stainless steel parts, 50 Ci in the heavy water; and above 600 Ci on the fuel and experimental channels. Specific activity of 60 Co was calculated to be 15 Ci/g on the reactor channels, 8 Ci/g on the stainless steel parts and 3 Ci/g in the heavy water. Decontamination of the aluminium parts was not done because it was considered it could initiate corrosion. Since the efficiency of distillation is increased it was expected that permanent distillation would remove most of the activity in the reactor channels

The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-01-01

Current interest in the thorium cycle, as an alternative to the uranium cycle, for water-moderated reactors is based on two attractive aspects of its use - the extension of uranium resources, and the related lower sensitivity of energy costs to uranium price. While most of the scientific basis required is already available, some engineering demonstrations are needed to provide better economic data for rational decisions. Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. There appear to be no major feasibility problems associated with the use of thorium, although development is required in the areas of fuel testing and fuel management. The use of thorium cycles implies recycling the fuel, and the major uncertainties are in the associated costs. Experience in the design and operation of fuel reprocessing and active-fabrication facilities is required to estimate costs to the accuracy needed for adequately defining the range of conditions economically favourable to thorium cycles. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An ''inventory'' of uranium of between 1 and 2Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium), is some two decades

Progress in design study on reduced-moderation water reactors

Energy Technology Data Exchange (ETDEWEB)

Okubo, Tsutomu; Kugo, Teruhiko; Shimada, Shoichiro; Shirakawa, Toshihisa; Iwamura, Takamichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Takeda, Renzo [Hitachi Ltd., Tokyo (Japan); Yokoyama, Tsugio [Toshiba Corp., Kawasaki, Kanagawa (Japan); Hibi, Koki [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Wada, Shigeyuki [Japan Atomic Power Co., Tokyo (Japan)

2000-06-01

The Reduced-Moderation Water Reactor (RMWR) is a next generation water-cooled reactor which aims at effective utilization of uranium resource, high burn-up and long operation cycle, and plutonium multi-recycle. These characteristics can be achieved by the high conversion ratio from {sup 238}U to {sup 239}Pu resulted from the higher neutron energy spectrum in comparison to conventional light water reactors. Considering the extension of LWR utilization, Japan Atomic Energy Research Institute (JAERI) started the research on it in 1997 and then started a collaboration in the conceptual design study with the Japan Atomic Power Company (JAPC) in 1998, under technical cooperation with three Japanese reactor vendors. In the core design study of the RMWR, negative void reactivity coefficient is required from a viewpoint of safety as well as establishing hard neutron spectrum. In order to achieve the above trade-off characteristics simultaneously, several basic core design ideas should be combined, such as a tight-lattice fuel assembly, a flat core, a blanket effect, a streaming effect and so on. Up to now, five core concepts have been created for the RMWR as follows: a high conversion BWR type core with high void fraction and super-flat core, a long operation cycle BWR type core using void tube assembly, a high conversion BWR type core without blankets, a high conversion PWR type core using heavy water as a coolant, and a PWR type core for plutonium multi-recycle using seed-blanket type fuel assemblies. Detailed feasibility studies for the RMWR have been continued on core design study. The present report summarizes the recent progress in the design study for the RMWR. (author)

Design of a thorium fuelled Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Krishnani, P.D.

2009-01-01

Full text: The main objective for development of Advanced Heavy Water Reactor (AHWR) is to demonstrate thorium fuel cycle technologies, along with several other advanced technologies required for next generation reactors, so that these are readily available in time for launching the third stage. The AHWR under design is a 300 MWe vertical pressure tube type thorium-based reactor cooled by boiling light water and moderated by heavy water. The fuel consists of (Th-Pu)O 2 and ( 233 ThU)O 2 pins. The fuel cluster is designed to generate maximum energy out of 233 U, which is bred in-situ from thorium and has a slightly negative void coefficient of reactivity, negative fuel temperature coefficient and negative power coefficient. For the AHWR, the well -proven pressure tube technology and online fuelling have been adopted. Core heat removal is by natural circulation of coolant during normal operation and shutdown conditions. Thus, it combines the advantages of light water reactors and PHWRs and removes the disadvantages of PHWRs. It has several passive safety systems for reactor normal operation, decay heat removal, emergency core cooling, confinement of radioactivity etc. The fuel cycle is based on the in-situ conversion of naturally available thorium into fissile 233 U in self sustaining mode. The uranium in the spent fuel will be reprocessed and recycled back into the reactor. The plutonium inventory will be kept a minimum and will come from fuel irradiated in Indian PHWRs. The 233 U required initially can come from the fast reactor programme or it can be produced by specially designing the initial core of AHWR using (Th,Pu)MOX fuel. There will be gradual transition from the initial core which will not contain any 233 U to an equilibrium core, which will have ( 233 U, Th) MOX fuel pins also in a composite cluster. The self sustenance is being achieved by a differential fuel loading of low and a relatively higher Pu in the composite clusters. The AHWR burns the

Investigation of the heavy water distillation system at the RA reactor

International Nuclear Information System (INIS)

Zecevic, V.; Badrljica, R.

1963-01-01

The heavy water distillation system was tested because this was not done before the reactor start-up. Detailed inspection of the system components showed satisfactory results. Leak testing was done as well as the testing of the instrumentation which enables reliable performance of the system. Performance testing was done with ordinary water and later 2700 l of heavy water from the reactor was purified, decreasing the activity by 45%

Heavy-Water Power Reactors. Proceedings Of A Symposium

International Nuclear Information System (INIS)

1968-01-01

Proceedings of a Symposium organized by the IAEA and held in Vienna, 11-15 September 1967. The timeliness of the meeting was underlined by the large gathering of over 225 participants from 28 countries and three international organizations. Contents: Experience with heavy-water power and experimental reactors and projects (14 papers); New and advanced power reactor designs and concepts (8 papers); Development programmes and thorium cycle (9 papers); Economics and prospects of heavy-water power reactors (7 papers); Physics and fuel management (8 papers); Fuels (5 papers); Safety, control and engineering (6 papers); Panel discussion. Except for one Russian paper, which is published in English, each paper is in its original language (49 English and 8 French) and is preceded by an abstract in English with a second one in the original language if this is not English. Discussions are in English. (author)

Heavy-Water Power Reactors. Proceedings Of A Symposium

Energy Technology Data Exchange (ETDEWEB)

NONE

1968-04-15

Proceedings of a Symposium organized by the IAEA and held in Vienna, 11-15 September 1967. The timeliness of the meeting was underlined by the large gathering of over 225 participants from 28 countries and three international organizations. Contents: Experience with heavy-water power and experimental reactors and projects (14 papers); New and advanced power reactor designs and concepts (8 papers); Development programmes and thorium cycle (9 papers); Economics and prospects of heavy-water power reactors (7 papers); Physics and fuel management (8 papers); Fuels (5 papers); Safety, control and engineering (6 papers); Panel discussion. Except for one Russian paper, which is published in English, each paper is in its original language (49 English and 8 French) and is preceded by an abstract in English with a second one in the original language if this is not English. Discussions are in English. (author)

Comparison of methods for the determination of boron in heavy water moderator

Energy Technology Data Exchange (ETDEWEB)

Green, L.W.; Davey, E.C.; Gulens, J.; Longhurst, T.H.; Mislan, J.P. (Atomic Energy of Canada Ltd., Chalk River, Ontario. Chalk River Nuclear Labs.)

1984-08-01

Five analysis methods were compared for the determination of boron in heavy water moderator: isotope dilution mass spectrometry, spectrophotometry, neutron activation, inductively coupled plasma -atomic emission spectrometry, and ion selective electrode potentiometry. Ten samples were analysed by each method; the results showed close agreement between all of the methods. Only mass spectrometry achieved the required precision (<1 percent rsd) for samples taken during initial reactor operation, but all of the methods achieved sufficient precision (<10 percent rsd) for samples taken during normal operation. For samples for which the /sup 10/B concentration must be determined, only mass spectrometry and neutron activation are applicable.

Operation management of the prototype heavy water reactor 'Fugen'

Energy Technology Data Exchange (ETDEWEB)

Muramatsu, Akira; Takei, Hiroaki; Iwanaga, Shigeru; Noda, Masao; Hara, Hidemi (Power Reactor and Nuclear Fuel Development Corp., Tokyo (Japan))

1983-09-01

The advanced thermal reactor Fugen power station has continued almost smooth operation since it began the full scale operation as the first homemade power reactor in Japan in March, 1979. In the initial period of operation, some troubles were experienced, but now, it can be said that the operational techniques of heavy water-moderated, boiling light water-cooled, pressure tube type reactors have been established, through the improvement of the operational method and equipment, and the operational experience. Also, the verification of the operational ability, maintainability, reliability and safety of this new type reactor, that is the mission of the prototype reactor, achieved steadily the good results. Hereafter, the verification of operational performance is the main objective because it is required for the design, construction and operation of the demonstration reactor. The organization for the operation management and operation, the communication at the time of the abnormality, the operation of the plant, that is, start up, stop and the operation at the rated output, the works during plant stoppage, the operation at the time of the plant abnormality, the operation of waste treatment facility and others, the improvement of the operational method, and the education and training of operators are reported.

Advances in heavy water reactors

International Nuclear Information System (INIS)

1994-03-01

The current IAEA programme in advanced nuclear power technology promotes technical information exchange between Member States with major development programmes. The Technical Committee Meeting (TCM) on Advances in Heavy Water Reactors was organized by the IAEA in the framework of the activities of the International Working Group on Advanced Technologies for Water Cooled Reactors (IWGATWR) and hosted by the Atomic Energy of Canada Limited. Sixty-five participants from nine countries (Canada, Czech Republic, India, German, Japan, Republic of Korea, Pakistan, Romania and USA) and the IAEA attended the TCM. Thirty-four papers were presented and discussed in five sessions. A separate abstract was prepared for each of these papers. All recommendations which were addressed by the participants of the Technical Committee meeting to the IWGATWR have been submitted to the 5th IWGATWR meeting in September 1993. They were reviewed and used as input for the preparation of the IAEA programme in the area of advanced water cooled reactors. This TCM was mainly oriented towards advances in HWRs and on projects which are now in the design process and under discussion. Refs, figs and tabs

Summary of the 4th workshop on the reduced-moderation water reactor

International Nuclear Information System (INIS)

Nakatsuka, Toru; Ishikawa, Nobuyuki; Iwamura, Takamichi

2001-09-01

The research on Reduced-Moderation Water Reactors (RMWRs) has been performed in JAERI for the development of future innovative reactors. The workshop on the RMWRs has been held every year since fiscal 1997 aimed at information exchange between JAERI and other organizations such as universities, laboratories, utilities and vendors. The 4th workshop was held on March 2, 2001 under the joint auspices of JAERI and North Kanto branch of Atomic Energy Society of Japan. The workshop began with three lectures on recent research activities in JAERI entitled 'Recent Situation of Research on Reduced-Moderation Water Reactor', 'Analysis on Electricity Generation Costs of Reduced Moderation Water Reactors' and 'Reprocessing Technology for Spent Mixed-Oxides Fuel from LWR'. Then five lectures followed: 'Micro Reactor Physics of MOX Fueled LWR' which shows the recent results of reactor physics, Fast Reactor Cooled by Supercritical Light Water' which is another type of reduced-moderation reactor, 'Phase 1 of Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC), 'Integral Type Small PWR with Stand-alone Safety' which is intended to suit for the future consumers' needs, and Utilization of Plutonium in Reduced-Moderation Water Reactors' which dictates benefits of plutonium utilization with RMWRs. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture, as well as presentation handouts, program and participant list as appendixes. The 8 of the presented papers are indexed individually. (J.P.N.)

Halden Boiling Water Reactor. Plant Performance and Heavy-Water Management

Energy Technology Data Exchange (ETDEWEB)

Aas, S.; Jamne, E.; Wullum, T.; Fjellestad, K. [Institutt for Atomenergi, OECD Halden Reactor Project, Halden (Norway)

1968-04-15

The Halden boiling heavy-water reactor, designed and built by the Norwegian Institutt for Atomenergi, has since June 1958 been operated as an international project. On its second charge the reactor was operated at power levels up to 25 MW and most of the time at a pressure of 28.5 kg/cm{sup 2}. During the period from July 1964 to December 1966 the plant availability was close to 64% including shutdowns because of test fuel failures and loading/unloading of fuel. Disregarding such stops, the availability was close to 90%. The average burnup of the core is about 6200 MWd/t UO{sub 2} : the most highly exposed elements have reached 10000 MWd/t UO{sub 2}. The transition temperature of the reactor tank has been followed closely. The results of the surveillance programme and the implication on the reactor operation are discussed. The reactor is located in a cave in a rock. Some experiences with such a containment are given. To locate failed test-fuel elements a fuel failure location system has been installed. A fission gas collection system has saved valuable reactor time during clean-up of the reactor system following test fuel failures. Apart from one incident with two of the control stations, the plant control and instrumentation systems have functioned satisfactorily. Two incidents with losses of 150 and 200 kg of heavy water have occurred. However, after improved methods for leakage detection had been developed, the losses have been kept better than 50 g/h . Since April 1962 the isotopic purity of the heavy water (14 t) has decreased from 99.75 to 99.62%. The tritium concentration is now slightly above 700 {mu}C/cm{sup 3}. This activity level has not created any serious operational or maintenance problems. An extensive series of water chemistry experiments has been performed to study the influence of various operating parameters on radiolytic gas formation. The main results of these experiments will be reported. Different materials such as mild steel, ferritic steel

Tritium concentration in the heavy water upgrading plants

International Nuclear Information System (INIS)

Croitoru, C.; Pop, F.; Titescu, Gh.; Dumitrescu, M.; Ciortea, C.; Stefanescu, I.; Peculea, M.; Pitigoi, Gh.; Trancota, D. . E-mail of corresponding author: croitoru@icsi.ro; Croitoru, C.)

2005-01-01

In the course of time heavy water used in CANDU nuclear power plants, as moderator or coolant, degrades, as a result of its impurification with light water and tritium. Concentration diminution below 99.8% mol for moderator and 99.75% mol for coolant causes an inefficient functioning of CANDU reactor. By isotopic distillation, light water is removed. Simultaneously tritium concentration takes place. The heavy water upgrading plant from Cernavoda is an isotopic separation cascade with two stages. The paper presents, for this plant, a theoretical study of the tritium concentration. (author)

Economic and safety aspects of using moderator heat for feed water heating in a nuclear power plant

International Nuclear Information System (INIS)

Patwegar, I.A.; Dutta, Anu; Chaki, S.K.; Venkat Raj, V.

2002-01-01

Full text: In the proposed advanced heavy water reactor (AHWR), coolant and moderator are separated by the coolant channel. The coolant absorbs most of the fission heat produced in the reactor core. However, the moderator absorbs about 5 to 6 % of the fission heat. In a reactor producing 750 MW(th) power, this moderator heat is about 40 MW. In the present Indian PHWR (pressurized heavy water reactor) systems, this moderator heat is lost to a sink through the moderator heat exchangers, which are cooled by process water. This paper presents the results of the steam cycle analysis carried out for AHWR using moderator heat exchangers as part of the feed heating system. The present study is an attempt to determine the gain in electrical output (MW) if moderator heat is utilized for feed water heating. The operational and safety aspects of using moderator heat are also discussed in the paper

Summary of the 4th workshop on the reduced-moderation water reactor

Energy Technology Data Exchange (ETDEWEB)

Nakatsuka, Toru; Ishikawa, Nobuyuki; Iwamura, Takamichi (eds.) [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-09-01

The research on Reduced-Moderation Water Reactors (RMWRs) has been performed in JAERI for the development of future innovative reactors. The workshop on the RMWRs has been held every year since fiscal 1997 aimed at information exchange between JAERI and other organizations such as universities, laboratories, utilities and vendors. The 4th workshop was held on March 2, 2001 under the joint auspices of JAERI and North Kanto branch of Atomic Energy Society of Japan. The workshop began with three lectures on recent research activities in JAERI entitled 'Recent Situation of Research on Reduced-Moderation Water Reactor', 'Analysis on Electricity Generation Costs of Reduced Moderation Water Reactors' and 'Reprocessing Technology for Spent Mixed-Oxides Fuel from LWR'. Then five lectures followed: 'Micro Reactor Physics of MOX Fueled LWR' which shows the recent results of reactor physics, Fast Reactor Cooled by Supercritical Light Water' which is another type of reduced-moderation reactor, 'Phase 1 of Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC), 'Integral Type Small PWR with Stand-alone Safety' which is intended to suit for the future consumers' needs, and Utilization of Plutonium in Reduced-Moderation Water Reactors' which dictates benefits of plutonium utilization with RMWRs. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture, as well as presentation handouts, program and participant list as appendixes. The 8 of the presented papers are indexed individually. (J.P.N.)

Feasibility study and economic analysis on thorium utilization in heavy water reactors

International Nuclear Information System (INIS)

1978-07-01

Even though natural uranium is a more easily usable fuel in heavy water reactors, thorium fuel cycles have also been considered owing to certain attractive features of the thorium fuel cycle in heavy water reactors. The relatively higher fission neutron yield per thermal neutron absorption in 233 U combined with the very low neutron absorption cross section of heavy water make it possible to achieve breeding in a heavy water reactor operating on Th- 233 U fuel cycle. Even if the breeding ratio is very low, once a self-sustaining cycle is achieved, thereafter dependence on uranium can be completely eliminated. Thus, with a self-sustaining Th- 233 U fuel cycle in heavy water reactors, a given quantity of natural uranium will be capable of supporting a much larger installed generating capacity to significantly longer period of time. However, since thorium does not contain any fissile isotope, fissile material has to be added at the beginning. Concentrated fissile material is considerably more expensive than the 235 U contained in natural uranium. This makes the fuel cycle cost higher with thorium fuel cycle, at least during the initial stages. The situation is made worse by the fact that, because of its higher thermal neutron absorption cross section, thorium requires a higher concentration of fissile material than 238 U. Nevertheless, because of the superior nuclear characteristics of 233 U, once uranium becomes more expensive, thorium fuel cycle in heavy water reactors may become economically acceptable. Furthermore, the energy that can be made available from a given quantity of uranium is considerably increased with a self-sustaining thorium fuel cycle

Heavy water isotopic rectification in the ''ORPHEE'' reactor. SACLAY studies Centre

International Nuclear Information System (INIS)

Lejeune, P.; Breant, P.

1993-01-01

ORPHEE reactor supplies neutron beams, which are got back in a heavy water reflector. The neutron beams intensity depends on the reflector quality which is determined by the isotopic content of the heavy water. The deuterium submitted to core irradiation changes in radioactive tritium which must be eliminated largely for reasons of safety. The column must keep the heavy water isotopic content of the reflector to a value higher than 99.8% by eliminating light water by fractional distillation or rectification. This column is also used for the tritium elimination of heavy water. 13 figs

Summary of the 3rd workshop on the reduced-moderation water reactor

International Nuclear Information System (INIS)

Ishikawa, Nobuyuki; Nakatsuka, Tohru; Iwamura, Takamichi

2000-06-01

The research activities of a Reduced-Moderation Water Reactor (RMWR) are being performed for a development of the next generation water-cooled reactor. A workshop on the RMWR was held on March 3rd 2000 aiming to exchange information between JAERI and other organizations such as universities, laboratories, utilities and vendors. This report summarizes the contents of lectures and discussions on the workshop. The 1st workshop was held on March 1998 focusing on the review of the research activities and future research plan. The succeeding 2nd workshop was held on March 1999 focusing on the topics of the plutonium utilization in water-cooled reactors. The 3rd workshop was held on March 3rd 2000, which was attended by 77 participants. The workshop began with a lecture titled 'Recent Situation Related to Reduced-Moderation Water Reactor (RMWR)', followed by 'Program on MOX Fuel Utilization in Light Water Reactors' which is the mainstream scenario of plutonium utilization by utilities, and 'Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC). Also, following lectures were given as the recent research activities in JAERI: 'Progress in Design Study on Reduced-Moderation Water Reactors', 'Long-Term Scenarios of Power Reactors and Fuel Cycle Development and the Role of Reduced Moderation Water Reactors', 'Experimental and Analytical Study on Thermal Hydraulics' and Reactor Physics Experiment Plan using TCA'. At the end of the workshop, a general discussion was performed about the research and development of the RMWR. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture and general discussion, as well as presentation viewgraphs, program and participant list as appendixes. The 7 of the presented papers are indexed individually. (J.P.N.)

Summary of the 3rd workshop on the reduced-moderation water reactor

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Nobuyuki; Nakatsuka, Tohru; Iwamura, Takamichi [eds.

2000-06-01

The research activities of a Reduced-Moderation Water Reactor (RMWR) are being performed for a development of the next generation water-cooled reactor. A workshop on the RMWR was held on March 3rd 2000 aiming to exchange information between JAERI and other organizations such as universities, laboratories, utilities and vendors. This report summarizes the contents of lectures and discussions on the workshop. The 1st workshop was held on March 1998 focusing on the review of the research activities and future research plan. The succeeding 2nd workshop was held on March 1999 focusing on the topics of the plutonium utilization in water-cooled reactors. The 3rd workshop was held on March 3rd 2000, which was attended by 77 participants. The workshop began with a lecture titled 'Recent Situation Related to Reduced-Moderation Water Reactor (RMWR)', followed by 'Program on MOX Fuel Utilization in Light Water Reactors' which is the mainstream scenario of plutonium utilization by utilities, and 'Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC). Also, following lectures were given as the recent research activities in JAERI: 'Progress in Design Study on Reduced-Moderation Water Reactors', 'Long-Term Scenarios of Power Reactors and Fuel Cycle Development and the Role of Reduced Moderation Water Reactors', 'Experimental and Analytical Study on Thermal Hydraulics' and Reactor Physics Experiment Plan using TCA'. At the end of the workshop, a general discussion was performed about the research and development of the RMWR. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture and general discussion, as well as presentation viewgraphs, program and participant list as appendixes. The 7 of the presented papers are indexed individually. (J.P.N.)

Water cooled reactor technology: Safety research abstracts no. 1

International Nuclear Information System (INIS)

1990-01-01

The Commission of the European Communities, the International Atomic Energy Agency and the Nuclear Energy Agency of the OECD publish these Nuclear Safety Research Abstracts within the framework of their efforts to enhance the safety of nuclear power plants and to promote the exchange of research information. The abstracts are of nuclear safety related research projects for: pressurized light water cooled and moderated reactors (PWRs); boiling light water cooled and moderated reactors (BWRs); light water cooled and graphite moderated reactors (LWGRs); pressurized heavy water cooled and moderated reactors (PHWRs); gas cooled graphite moderated reactors (GCRs). Abstracts of nuclear safety research projects for fast breeder reactors are published independently by the Nuclear Energy Agency of the OECD and are not included in this joint publication. The intention of the collaborating international organizations is to publish such a document biannually. Work has been undertaken to develop a common computerized system with on-line access to the stored information

Investigating heavy water zero power reactors with a new core configuration based on experiment and calculation results

Energy Technology Data Exchange (ETDEWEB)

Nasrazadani, Zahra; Salimi, Raana; Askari, Afrooz; Khorsandi, Jamshid; Mirvakili, Mohammad; Mashayekh, Mohammad [Reactor Research School, Nuclear Science and Technology Research Institute, Atomic Energy Organization of Iran, Esfahan (Iran, Islamic Republic of)

2017-02-15

The heavy water zero power reactor (HWZPR), which is a critical assembly with a maximum power of 100 W, can be used in different lattice pitches. The last change of core configuration was from a lattice pitch of 18-20 cm. Based on regulations, prior to the first operation of the reactor, a new core was simulated with MCNP (Monte Carlo N-Particle)-4C and WIMS (Winfrith Improved Multigroup Scheme)-CITATON codes. To investigate the criticality of this core, the effective multiplication factor (Keff) versus heavy water level, and the critical water level were calculated. Then, for safety considerations, the reactivity worth of D2O, the reactivity worth of safety and control rods, and temperature reactivity coefficients for the fuel and the moderator, were calculated. The results show that the relevant criteria in the safety analysis report were satisfied in the new core. Therefore, with the permission of the reactor safety committee, the first criticality operation was conducted, and important physical parameters were measured experimentally. The results were compared with the corresponding values in the original core.

Loss of coolant analysis for CIRENE-LATINA heavy water reactor

International Nuclear Information System (INIS)

Chiantore, B.; Dubbini, M.; Proto, G.

1978-01-01

CIRENE is a heavy-water moderated, boiling water cooled pressure tube reactor. Fuel is natural uranium. A variety of breaks in the primary coolant system have been postulated for the analysis of the CIRENE Latina Plant (now under construction) such as double-end break of inlet header, downcomer, steam line and inlet feeders. The basic tool for analysis is the TILT-N Code which has been purposely developed for simulating the nuclear, thermal and hydrodynamic behaviour of the CIRENE core and associated heat transport system. An extensive full-scale test programme has been carried out by CNEN and CISE which fully confirms the adequacy of the model. The main results of the analysis show that maximum temperatures are far from those leading to significant fuel damage and that adequate core cooling is provided over the whole transient. (author)

The development of reactor vessel internal heavy forging for 1000 MW pressurized-water reactor nuclear power plant

International Nuclear Information System (INIS)

Zhang Zhifeng; Chen Yongbo; Ding Xiuping; Zhang Lingfang

2012-01-01

This Paper introduced the development of Reactor Vessel Internal (RVI) heavy forgings for 1000 MW Pressurized Water Reactor (PWR) nuclear power plant, analyzed the manufacture difficulties and technical countermeasures. The testing result of the product indicated that the performance of RVI heavy forgings manufactured by Shanghai Heavy Machinery Plant Ld. (SHMP) is outstanding and entirely satisfy the technical requirements for RVI product. (authors)

Parametric studies to establish natural circulation in advanced heavy water reactor

Energy Technology Data Exchange (ETDEWEB)

Bhatia, S K; Dhawan, M L [Reactor Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Design of Advanced Heavy Water Reactor (AHWR) is in progress. It consists of vertical pressure tubes with boiling light water coolant flowing through the tubes and heavy water moderator in the calandria. In PHWRs, core heat removal is through forced circulation of the coolant by PHT pumps. In AHWR, no PHT pumps are used and core heat is carried away by natural circulation of the coolant due to density difference between steam/water mixture inside the core and the water region outside the core. This passive means of core heat removal results in a number of benefits viz. (a) extra length of piping, valves, instruments, power supply and control systems for functioning of instruments are eliminated, (b) plant layout is simplified, (c) maintenance of valves and instruments is reduced. Natural circulation in AHWR is achieved by keeping the steam drum at a sufficient height above the core to get the required driving force. The loop height depends on many factors i.e. channel power, V{sub c}/V{sub f} ratio (ratio of coolant volume to fuel volume) and core height. The effect of these parameters on the loop height to establish natural circulation have been studied and presented. (author). 1 ref., 1 fig., 1 tab.

Finishing and upgrading of heavy water

International Nuclear Information System (INIS)

Butler, J.P.; Hammerli, M.

1981-01-01

This invention provides a process and apparatus for deuterium enrichment as a final stage in a heavy water plant, for continuous on-line enrichment of the heavy water in moderator and heat transfer systems in heavy water nuclear reactors, and for enrichment of hevy water that has been downgraded with natural water during the course of operating a heavy water nuclear reactor. The method comprises contacting partially-enriched heavy water feed in a catalyst column with hydrogen gas (essentially D 2 ) orginating in an electrolysis cell so as to enrich the feed water with deuterium extracted from the electrolytic hydrogen gas and passing the deuterium-enriched water to the electrolysis cell. The apparatus comprises a catalyst isotope exchange column with hydrogen gas and liquid water passing through in countercurrent isotope exchange, an electrolysis cell, a dehumidifer-scrubber; and means for passing the liquid water enriched in deuterium from the catalyst column through the dehumidifer-scrubber to the electrolysis cell, for passing the hydrogen gas evolved in the cathode side of the cell through the dehumidifier-scrubber to the catalyst column, for passing the hydrogen gas from the catalyst column to an output, for introducing an input water feed to the upper portion of the catalyst column, and for taking a product enriched in deuterium from the system. (LL)

Probablistic risk assessment methodology application to Indian pressurised heavy water reactors

International Nuclear Information System (INIS)

Babar, A.K.; Grover, R.B.; Mehra, V.K.; Gangwal, D.K.; Chakraborty, G.

1987-01-01

Probabilistic risk assessment in the context of nuclear power plants is associated with models that predict the offsite radiological releases resulting from reactor accidents. Level 1 PRA deals with the identification of accident sequences relevant to the design of a system and also with their quantitative estimation. It is characterised by event tree, fault tree analysis. The initiating events applicable to pressurised heavy water reactors have been considered and the dominating initiating events essential for detailed studies are identified in this paper. Reliability analysis and the associated problems encountered during the case studies are mentioned briefly. It is imperative to validate the failure data used for analysis. Bayesian technique has been employed for the same and a brief account is included herein. A few important observations, e.g. effects of the presence of moderator, made during the application of probabilistic risk assessment methodology are also discussed. (author)

The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-05-01

Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An 'inventory' of uranium of between 1 and 2 Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium) is some two decades

Nuclear calculation methods for light water moderated reactors

International Nuclear Information System (INIS)

Hicks, D.

1961-02-01

This report is intended as an introductory review. After a brief discussion of problems encountered in the nuclear design of water moderated reactors a comprehensive scheme of calculations is described. This scheme is based largely on theoretical methods and computer codes developed in the U.S.A. but some previously unreported developments made in this country are also described. It is shown that the effective reproduction factor of simple water moderated lattices may be estimated to an accuracy of approximately 1%. Methods for treating water gap flux peaking and control absorbers are presented in some detail, together with a brief discussion of temperature coefficients, void coefficients and burn-up problems. (author)

Fuel cycle options for light water reactors and heavy water reactors. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1999-11-01

In the second half of the 20th century nuclear power has evolved from the research and development environment to an industry that supplies 16% of the world's electricity. By the end of 1997, over 8500 reactor-years of operating experience had been accumulated. Global environmental change, and the continuing increase in global energy supply required to provide increasing populations with an improving standard of living, make the contribution from nuclear energy even more important for the next century. For nuclear power to achieve its full potential and make its needed contribution, it must be safe, economical, reliable and sustainable. All of these factors can be enhanced by judicious choice and development of advanced fuel cycle options. The Technical Committee Meeting (TCM) on Fuel Cycle Options for Light Water Reactors and Heavy Water Reactors was hosted by Atomic Energy of Canada Limited (AECL) on behalf of the Canadian Government and was jointly conducted within the frame of activities of the IAEA International Working Group on Advanced Technologies for Light Water Reactors (IWG-LWR) and the IAEA International Working Group on Advanced Technologies for Heavy Water Reactors (IWG-HWR). The TCM provided the opportunity to have in-depth discussions on important technical topics which were highlighted in the International Symposium on Nuclear Fuel Cycle and Reactor Strategies: Adjusting to New Realities, held in Vienna, 3-6 June 1997. The main results and conclusions of the TCM were presented as input for discussion at the first meeting of the IAEA newly formed International Working Group on Fuel Cycle Options

Benchmark testing of Canadol-2.1 for heavy water reactor

International Nuclear Information System (INIS)

Liu Ping

1999-01-01

The new version evaluated nuclear data library of ENDF-B 6.5 has been released recently. In order to compare the quality of evaluated nuclear data CENDL-2.1 with ENDF-B 6.5, it is necessary to do benchmarks testing for them. In this work, CENDL-2.1 and ENDF-B 6.5 were used to generated the WIMS-69 group library respectively, and benchmarks testing was done for the heavy water reactor, using WIMS5A code. It is obvious that data files of CENDL-2.1 is better than that of old WIMS library for the heavy water reactors calculations, and is in good agreement with those of ENDF-B 6.5

Fuel cycle flexibility in Advanced Heavy Water Reactor (AHWR) with the use of Th-LEU fuel

International Nuclear Information System (INIS)

Thakur, A.; Singh, B.; Pushpam, N.P.; Bharti, V.; Kannan, U.; Krishnani, P.D.; Sinha, R.K.

2011-01-01

The Advanced Heavy Water Reactor (AHWR) is being designed for large scale commercial utilization of thorium (Th) and integrated technological demonstration of the thorium cycle in India. The AHWR is a 920 MW(th), vertical pressure tube type cooled by boiling light water and moderated by heavy water. Heat removal through natural circulation and on-line fuelling are some of the salient features of AHWR design. The physics design of AHWR offers considerable flexibility to accommodate different kinds of fuel cycles. Our recent efforts have been directed towards a case study for the use of Th-LEU fuel cycle in a once-through mode. The discharged Uranium from Th-LEU cycle has proliferation resistant characteristics. This paper gives the initial core, fuel cycle characteristics and online refueling strategy of Th-LEU fuel in AHWR. (author)

Current developments and future challenges in physics analyses of the NRU heavy water research reactor

Energy Technology Data Exchange (ETDEWEB)

Nguyen, S.; Wilkin, B.; Leung, T., E-mail: nguyens@aecl.ca, E-mail: leungt@aecl.ca [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

2011-07-01

The National Research Universal (NRU) reactor is heavy water cooled and moderated, with on-power fueling capability. TRIAD, a 3D two-group diffusion code, is currently used for support of day-to-day NRU operations. Recently, an MCNP full reactor model of NRU has been developed for benchmarking TRIAD. While reactivity changes and flux and power distributions from both methods are in reasonably good agreement, MCNP appears to eliminate a k-eff bias in TRIAD. Beyond TRIAD's capability, MCNP enables the assessment of radiation in the NRU outer structure. Challenges include improving TRIAD accuracy and MCNP performance, as well as performing NRU core-following using MCNP. (author)

Study of the consequences of the rupture of a pressure tube in the tank of a gas-cooled, heavy-water moderated reactor

International Nuclear Information System (INIS)

Hareux, F.; Roche, R.; Vrillon, B.

1964-01-01

Bursting of a pressure tube in the tank of a heavy water moderated-gas cooled reactor is an accident which has been studied experimentally about EL-4. A first test (scale 1) having shown that the burst of a tube does not cause the rupture of adjacent tubes, tests on the tank resistance have been undertaken with a very reduced scale model (1 to 10). It has been found that the tank can endure many bursts of tube without any important deformation. Transient pressure in the tank is an oscillatory weakened wave, the maximum of which (pressure peak) has been the object of a particular experimental study. It appears that the most important parameters which affect the pressure peak are; the pressure of the gas included in the bursting pressure tube, the volume of this gas, the mass of air included in the tank and the nature of the gas. A general method to calculate the pressure peak value in reactor tanks has been elaborated by direct application of experimental data. (authors) [fr

The effect of heavy water reactors and liquid fuel reactors on the long-term development of nuclear energy

International Nuclear Information System (INIS)

Brand, P.; Wiechers, W.K.

1974-01-01

The effects of the rates at which various combinations of power reactor types are installed on the long-range (to the year 2040) uranium and plutonium inventory requirements are examined. Consideration is given to light water reactors, fast breeder reactors, high temperature gas-cooled reactors, heavy water reactors, and thermal breeder reactors, in various combinations, and assuming alternatively a 3% and a 5% growth in energy demand

Neutron disadvantage factors in heavy water and light water reactors

International Nuclear Information System (INIS)

Pop-Jordanov, J.

1966-01-01

A number od heavy water and light water reactor cells are analyzed in this paper by applying analytical methods of neutron thermalization. Calculations done according to the one-group Amouyal-Benoist method are included in addition. Computer codes for ZUSE Z-23 computer were written by applying both methods. The obtained results of disadvantage factors are then compared to results obtained by one-group P 3 approximation and by multigroup K7-THERMOS code [sr

Advances in commercial heavy water reactor power stations

International Nuclear Information System (INIS)

Brooks, G.L.

1987-01-01

Generating stations employing heavy water reactors have now firmly established an enviable record for reliable, economic electricity generation. Their designers recognize, however, that further improvements are both possible and necessary to ensure that this reactor type remains attractively competitive with alternative nuclear power systems and with fossil-fuelled generation plants. This paper outlines planned development thrusts in a number of important areas, viz., capital cost reduction, advanced fuel cycles, safety, capacity factor, life extension, load following, operator aida, and personnel radiation exposure. (author)

Natural-circulation flow pattern during the gamma-heating phase of an LBLOCA in a heavy-water moderated reactor

International Nuclear Information System (INIS)

Rodriguez, S.B.; Unal, C.; Pasamehmetoglu, K.O.; Motley, F.E.

1992-01-01

In a postulated large-break loss-of-coolant accident (LBLOCA), the core of the reactor is uncovered quickly as the liquid that drains out of the tank is replaced by air. During the LBLOCA, the reactor is scrammed. the moderator tank is drained, and fuel and control rod tubes are cooled internally by forced convection via the emergency cooling system (ECS) water. However, the safety rods, reflector assemblies, tank wall, and instrument rods continue to heat up as a result of gamma deposition. These components are primarily cooled by natural/mixed convection and radiation heat transfer. In this paper, the thermal-hydraulic analysis of a reactor moderator tank exposed to air during an LBLOCA is discussed. The analysis was performed using a special version of the Transient Reactor Analysis Code (TRAC). TRAC input and code modifications considered the appropriate modeling of ECS cooling, thermal radiation heat transfer, and natural convection. The major objective of the model was to calculate the limiting component temperature (that establishes the maximum operating power) as a result of gamma heating. In addition, the nature of the moderator tank air-circulation pattern and its effects on the limiting temperature under various conditions were analyzed. None of the components were found to exceed their structural limits when the pre-scram power level was 50% of historical power

Removal of aluminum turbidity from heavy water reactors by precipitation ion exchange using magnesium hydroxide

International Nuclear Information System (INIS)

Venkateswarlu, K.S.; Shanker, R.; Velmurugan, S.; Venkateswaran, G.; Rao, M.R.

1988-01-01

A special magnesium hydroxide MG(OH)/sub 2/ sorber, loaded onto an ion-exchange matrix has been developed to remove hydrated alumina turbidity in heavy water. This sorber was applied to the coolant/moderator system in the research reactor Dhruva. The sorber not only removed turbidity but also suspended uranium at parts per billion levels and associated β, γ activity. The sorption is based on the attraction between the positively charged Mg(OH)/sub 2/ surface and the negatively charged hydrated alumina particles

A study on the establishment of component/equipment performance criteria considering Heavy Water Reactor characteristics

Energy Technology Data Exchange (ETDEWEB)

Chang, Keun Sun; Kwon, Young Chul; Lee, Min Kyu; Lee, Yun Soo [Sunmoon Univ., Asan (Korea, Republic of); Chang, Seong Hoong; Ryo, Chang Hyun [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Kim, Soong Pyung; Hwnag, Jung Rye; Chung, Chul Kee [Chosun Univ., Gwangju (Korea, Republic of)

2002-03-15

Foreign and domestic technology trends, regulatory requirements, design and researches for heavy water reactors are analyzed. Safety design guides of Canada industry and regulatory documents and consultative documents of Canada regulatory agency are reviewed. Applicability of MOST guidance 16 Revision 'guidance for technical criteria of nuclear reactor facility' is reviewed. Specific performance criteria are established for components and facilities for heavy water reactor.

Good practices in heavy water reactor operation

International Nuclear Information System (INIS)

2010-06-01

The value and importance of organizations in the nuclear industry engaged in the collection and analysis of operating experience and best practices has been clearly identified in various IAEA publications and exercises. Both facility safety and operational efficiency can benefit from such information sharing. Such sharing also benefits organizations engaged in the development of new nuclear power plants, as it provides information to assist in optimizing designs to deliver improved safety and power generation performance. In cooperation with Atomic Energy of Canada, Ltd, the IAEA organized the workshop on best practices in Heavy Water Reactor Operation in Toronto, Canada from 16 to 19 September 2008, to assist interested Member States in sharing best practices and to provide a forum for the exchange of information among participating nuclear professionals. This workshop was organized under Technical Cooperation Project INT/4/141, on Status and Prospects of Development for and Applications of Innovative Reactor Concepts for Developing Countries. The workshop participants were experts actively engaged in various aspects of heavy water reactor operation. Participants presented information on activities and practices deemed by them to be best practices in a particular area for consideration by the workshop participants. Presentations by the participants covered a broad range of operational practices, including regulatory aspects, the reduction of occupational dose, performance improvements, and reducing operating and maintenance costs. This publication summarizes the material presented at the workshop, and includes session summaries prepared by the chair of each session and papers submitted by the presenters

Possibility of using metal uranium fuel in heavy water reactors

International Nuclear Information System (INIS)

Djuric, B.; Mihajlovic, A.; Drobnjak, Dj.

1965-01-01

The review of metal uranium properties including irradiation in the reactor core lead to the following conclusions. Using metal uranium in the heavy water reactors would be favourable from economic point of view for ita high density, i.e. high conversion factor and low cost of fuel elements fabrication. Most important constraint is swelling during burnup and corrosion

Study on core design for reduced-moderation water reactors

International Nuclear Information System (INIS)

Okubo, Tsutomu

2002-01-01

The Reduced-Moderation Water Reactor (RMWR) is a water-cooled reactor with the harder neutron spectrum comparing with the LWR, resulting from low neutron moderation due to reduced water volume fraction. Based on the difference from the spectrum from the LWR, the conversion from U-238 to Pu-239 is promoted and the new cores preferable to effective utilization of uranium resource can be possible Design study of the RMWR core started in 1997 and new four core concepts (three BWR cores and one PWR core) are recently evaluated in terms of control rod worths, plutonium multiple recycle, high burnup and void coefficient. Comparative evaluations show needed incorporation of control rod programming and simplified PUREX process as well as development of new fuel cans for high burnup of 100 GW-d/t. Final choice of design specifications will be made at the next step aiming at realization of the RMWR. (T. Tanaka)

Study on core design for reduced-moderation water reactors

Energy Technology Data Exchange (ETDEWEB)

Okubo, Tsutomu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-12-01

The Reduced-Moderation Water Reactor (RMWR) is a water-cooled reactor with the harder neutron spectrum comparing with the LWR, resulting from low neutron moderation due to reduced water volume fraction. Based on the difference from the spectrum from the LWR, the conversion from U-238 to Pu-239 is promoted and the new cores preferable to effective utilization of uranium resource can be possible Design study of the RMWR core started in 1997 and new four core concepts (three BWR cores and one PWR core) are recently evaluated in terms of control rod worths, plutonium multiple recycle, high burnup and void coefficient. Comparative evaluations show needed incorporation of control rod programming and simplified PUREX process as well as development of new fuel cans for high burnup of 100 GW-d/t. Final choice of design specifications will be made at the next step aiming at realization of the RMWR. (T. Tanaka)

The variation of the reactivity with the number, diameter and length of the control rods in a heavy water natural uranium reactor

Energy Technology Data Exchange (ETDEWEB)

McCriric, H

1958-05-15

Starting with the known reactor constants for a heavy water moderated reactor with reflector and a given number of control rods of a certain size, the reactivity equivalence of the control rods is calculated. The calculation is given in detail. The number, length and diameter of the control rods is then varied and the effect of these parameters on the reactivity is shown graphically. Flux plots are also given for the reactor with and without control rods.

Power spectral density measurements with 252Cf for a light water moderated research reactor

International Nuclear Information System (INIS)

King, W.T.; Mihalczo, J.T.

1979-01-01

A method of determining the reactivity of far subcritical systems from neutron noise power spectral density measurements with 252 Cf has previously been tested in fast reactor critical assemblies: a mockup of the Fast Flux Test Facility reactor and a uranium metal sphere. Calculations indicated that this measurement was feasible for a pressurized water reactor (PWR). In order to evaluate the ability to perform these measurements with moderated reactors which have long prompt neutron lifetimes, measurements were performed with a small plate-type research reactor whose neutron lifetime (57 microseconds) was about a factor of three longer than that of a PWR and approx. 50% longer than that of a boiling water reactor. The results of the first measurements of power spectral densities with 252 Cf for a water moderated reactor are presented

Liquid wall boiler and moderator (BAM) for heavy ion-pellet fusion reactors

International Nuclear Information System (INIS)

Powell, J.R.; Lazareth, O.; Fillo, J.

1977-11-01

Thick liquid wall blankets appear to be of great promise for heavy ion pellet fusion reactors. They avoid the severe problems of intense radiation and blast damage that would be encountered with solid blanket structures. The liquid wall material can be chosen so that its vapor pressure at the working temperature of the power cycle is well below the value at which it might interfere with the propagation of the heavy ion beam. The liquid wall can be arranged so that it does not contact any surrounding solid structure when the pellet explosion occurs, including the ends. The ends can be magnetically closed just before the pellet explosion, or a time phased flow can be used, which will leave a clear central zone into which the pellet is injected. Parametric analysis comparing three candidate liquid wall materials were carried out. The three materials were lithium, flibe, and lead (with a low concentration of disolved lithium). Lead appeared to be the best choice for the liquid wall, although any of the three should allow a practical reactor system. The parametric analyses examined the effects of pellet yield (0 to 10 GJ), pellet mass (3 g to 3 kg), liquid wall thickness (10 cm to 80 cm), vapor condensation time (0 to 10 milliseconds), degree of neutron moderation in the pellet (none to 100%), liquid wall chamber size (radius of 1.5 meters to 4 meters), Pb/Li 6 ratio (100 to 5,000), and thickness of graphite moderating zone behind the liquid wall

Reactivity effect of a heavy water tank as reflector in the IPEN/MB-01 reactor

International Nuclear Information System (INIS)

Santos, Adimir dos; Fuga, Rinaldo

2013-01-01

This experiment comprises a set of experiments performed in the IPEN/MB-01 reactor and described in the International Handbook of Evaluated Reactor Physics Benchmark Experiments, specifically the experiment aim to evaluate the reactivity due to the heavy water tank placed at reflector region of the IPEN/MB-01 reactor. An aluminum tank was designed to be filled with heavy water and positioned at the west face of the IPEN/MB-01, additionally the experiment was also designed to allow variable heavy water height inside of this tank providing different neutron leakage rate in the west face of the IPEN/MB-01, consequently providing a series of interesting combinations. The measured quantities in the experiment are reactivities and critical control bank positions for several combinations of the control banks and an excess of reactivity of the heavy water tank. The experiment will be simulated using a Monte Carlo code MCNP in order to compare the different critical control bank position. (author)

Design and development of face seal type sealing plug for advanced heavy water reactor

International Nuclear Information System (INIS)

Bansal, S.; Bhattacharyya, S.; Patel, R.J.; Agrawal, R.G.; Vaze, K.K.

2005-09-01

Advanced Heavy Water Reactor is a vertical pressure tube type reactor having light water as its coolant and heavy water as moderator. Sealing plug is required to close the pressure boundary of main heat transport system of the reactor by preventing escape of light water/steam From the coolant channel. There are 452 coolant channels in the reactor located in square lattice pitch. Sealing plug is located at the top of each coolant channel (in the top end fitting). Top end fitting is having a stepped bore to create a sealing face. Sealing plug is held through its expanded jaws in a specially provided groove of the end fitting. The plug was designed and prototypes were manufactured considering its functional importance, intricate design and precision machining requirements. Sealing plug consists of about 20 components mostly made up of precipitation hardening stainless steel, which is suitable for water environment and meets other requirements of strength and resistance to wear and galling. Seal disc is a critical component of the sealing plug as it is the pressure-retaining component. It is a circular disc with protruded stem. One face of the seal disc is nickel plated in the peripheral area that creates the sealing by abutting against the sealing face provided in the end fitting. The typical shape and profile of seal disc provides flexibility and allows elastic deformation to assist in locking of sealing plug and creating adequate seating force for effective sealing. Design and development aspects of the sealing plug have been detailed out in this report. Also results of stress analysis and experimental studies for seal disc have been mentioned in the report. Stress analysis and experimental testing was required for the seal disc because high stresses are developed due to its exposure to high pressure and temperature environment of Main Heat Transport system. Hot testing was carried out to simulate the reactor-simulated condition. The performance was found to be

Possibilities of using metal uranium fuel in heavy water reactors

International Nuclear Information System (INIS)

Djuric, B.; Mihajlovic, A.; Drobnjak, Dj.

1965-11-01

There are serious economic reasons for using metal uranium in heavy water reactors, because of its high density, i.e. high conversion factor, and low cost of fuel elements production. Most important disadvantages are swelling at high burnup and corrosion risk. Some design concepts and application of improved uranium obtained by alloying are promising for achievement of satisfactory stability of metal uranium under reactor operation conditions [sr

Application of fuzzy logic control system for reactor feed-water control

International Nuclear Information System (INIS)

Iijima, T.; Nakajima, Y.

1994-01-01

The successful actual application of a fuzzy logic control system to the a nuclear Fugen nuclear power reactor is described. Fugen is a heavy-water moderated, light-water cooled reactor. The introduction of fuzzy logic control system has enabled operators to control the steam drum water level more effectively in comparison to a conventional proportional-integral (PI) control system

Conceptual mechanical design for a pressure-tube type supercritical water-cooled reactor

Energy Technology Data Exchange (ETDEWEB)

Yetisir, M.; Diamond, W.; Leung, L.K.H.; Martin, D.; Duffey, R. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

2011-07-01

This paper presents a conceptual mechanical design for a heavy-water-moderated pressure-tube supercritical water (SCW) reactor, which has evolved from the well-established CANDU nuclear reactor. As in the current designs, the pressure-tube SCW reactor uses a calandria vessel and, as a result, many of today's technologies (such as the shutdown safety systems) can readily be adopted with small changes. Because the proposed concept uses a low-pressure moderator, it does not require a pressure vessel that is subject to the full SCW pressure and temperature conditions. The proposed design uses batch refueling and hence, the reactor core is orientated vertically. Significant simplifications result in the design with the elimination of on line fuelling systems, fuel channel end fittings and fuel channel closure seals and thus utilize the best features of Light Water Reactor (LWR) and Heavy Water Reactor (HWR) technologies. The safety goal is based on achieving a passive 'no core melt' configuration for the channels and core, so the mechanical features and systems directly reflect this desired attribute. (author)

Conceptual mechanical design for a pressure-tube type supercritical water-cooled reactor

International Nuclear Information System (INIS)

Yetisir, M.; Diamond, W.; Leung, L.K.H.; Martin, D.; Duffey, R.

2011-01-01

This paper presents a conceptual mechanical design for a heavy-water-moderated pressure-tube supercritical water (SCW) reactor, which has evolved from the well-established CANDU nuclear reactor. As in the current designs, the pressure-tube SCW reactor uses a calandria vessel and, as a result, many of today's technologies (such as the shutdown safety systems) can readily be adopted with small changes. Because the proposed concept uses a low-pressure moderator, it does not require a pressure vessel that is subject to the full SCW pressure and temperature conditions. The proposed design uses batch refueling and hence, the reactor core is orientated vertically. Significant simplifications result in the design with the elimination of on line fuelling systems, fuel channel end fittings and fuel channel closure seals and thus utilize the best features of Light Water Reactor (LWR) and Heavy Water Reactor (HWR) technologies. The safety goal is based on achieving a passive 'no core melt' configuration for the channels and core, so the mechanical features and systems directly reflect this desired attribute. (author)

Removal of gadolinium nitrate from heavy water

Energy Technology Data Exchange (ETDEWEB)

Wilde, E.W.

2000-03-22

Work was conducted to develop a cost-effective process to purify 181 55-gallon drums containing spent heavy water moderator (D2O) contaminated with high concentrations of gadolinium nitrate, a chemical used as a neutron poison during former nuclear reactor operations at the Savannah River Site (SRS). These drums also contain low level radioactive contamination, including tritium, which complicates treatment options. Presently, the drums of degraded moderator are being stored on site. It was suggested that a process utilizing biological mechanisms could potentially lower the total cost of heavy water purification by allowing the use of smaller equipment with less product loss and a reduction in the quantity of secondary waste materials produced by the current baseline process (ion exchange).

All heavy metals closed-cycle analysis on water-cooled reactors of uranium and thorium fuel cycle systems

International Nuclear Information System (INIS)

Permana, Sidik; Sekimoto, Hiroshi; Waris, Abdul; Takaki, Naoyuki

2009-01-01

Uranium and Thorium fuels as the basis fuel of nuclear energy utilization has been used for several reactor types which produce trans-uranium or trans-thorium as 'by product' nuclear reaction with higher mass number and the remaining uranium and thorium fuels. The utilization of recycled spent fuel as world wide concerns are spent fuel of uranium and plutonium and in some cases using recycled minor actinide (MA). Those fuel schemes are used for improving an optimum nuclear fuel utilization as well to reduce the radioactive waste from spent fuels. A closed-cycle analysis of all heavy metals on water-cooled cases for both uranium and thorium fuel cycles has been investigated to evaluate the criticality condition, breeding performances, uranium or thorium utilization capability and void reactivity condition. Water-cooled reactor is used for the basic design study including light water and heavy water-cooled as an established technology as well as commercialized nuclear technologies. A developed coupling code of equilibrium fuel cycle burnup code and cell calculation of SRAC code are used for optimization analysis with JENDL 3.3 as nuclear data library. An equilibrium burnup calculation is adopted for estimating an equilibrium state condition of nuclide composition and cell calculation is performed for calculating microscopic neutron cross-sections and fluxes in relation to the effect of different fuel compositions, different fuel pin types and moderation ratios. The sensitivity analysis such as criticality, breeding performance, and void reactivity are strongly depends on moderation ratio and each fuel case has its trend as a function of moderation ratio. Heavy water coolant shows better breeding performance compared with light water coolant, however, it obtains less negative or more positive void reactivity. Equilibrium nuclide compositions are also evaluated to show the production of main nuclides and also to analyze the isotopic composition pattern especially

High purity heavy water production: need for total organic carbon determination in process water streams

International Nuclear Information System (INIS)

Ayushi; Kumar, Sangita D.; Reddy, A.V.R.; Vithal, G.K.

2009-01-01

In recent times, demand for high purity heavy water (99.98% pure) in industries and laboratories has grown by manifold. Its application started in nuclear industry with the design of CANDU reactor, which uses natural uranium as fuel. In this reactor the purest grade of heavy water is used as the moderator and the primary coolant. Diverse industrial applications like fibre optics, medicine, semiconductors etc. use high purity heavy water extensively to achieve better performance of the specific material. In all these applications there is a stringent requirement that the total organic carbon content (TOC) of high purity heavy water should be very low. This is because the presence of TOC can lead to adverse interactions in different applications. To minimize the TOC content in the final product there is a need to monitor and control the TOC content at each and every stage of heavy water production. Hence a simple, rapid and accurate method was developed for the determination of TOC content in process water samples. The paper summarizes the results obtained for the TOC content in the water samples collected from process streams of heavy water production plant. (author)

Status of research and development on reduced-moderation water reactors

International Nuclear Information System (INIS)

Iwamura, Takamichi

2002-01-01

To improve uranium utilization, a design study of the Reduced-Moderation Water Reactor (RMWR) has been carried out intensively since 1998 at the Japan Atomic Energy Research Institute (JAERI). In this reactor, the nuclear fission reaction is designed to be realized mainly by high energy neutrons. To achieve this, the volume of water used to cool the fuel rods is decreased by reducing the gap width between the fuel rods. Conversion ratio greater than 1.0 is expected whether the core i-s cooled by boiling water or pressurized water and whether the core size is small or large. Status of the RMWR design is reviewed and planning of R and D for future deployment of this reactor after 20-20 is presented. To improve economics of this reactor, development of fuel cans for high burnup and low-cost reprocessing technology of mixed oxide spect fuels are highly needed. R and D has been conducted under the cooperation with utilities, industry, research organization and academia. (T. Tanaka)

Status of research and development on reduced-moderation water reactors

Energy Technology Data Exchange (ETDEWEB)

Iwamura, Takamichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2002-12-01

To improve uranium utilization, a design study of the Reduced-Moderation Water Reactor (RMWR) has been carried out intensively since 1998 at the Japan Atomic Energy Research Institute (JAERI). In this reactor, the nuclear fission reaction is designed to be realized mainly by high energy neutrons. To achieve this, the volume of water used to cool the fuel rods is decreased by reducing the gap width between the fuel rods. Conversion ratio greater than 1.0 is expected whether the core i-s cooled by boiling water or pressurized water and whether the core size is small or large. Status of the RMWR design is reviewed and planning of R and D for future deployment of this reactor after 20-20 is presented. To improve economics of this reactor, development of fuel cans for high burnup and low-cost reprocessing technology of mixed oxide spect fuels are highly needed. R and D has been conducted under the cooperation with utilities, industry, research organization and academia. (T. Tanaka)

Power flattening and reactivity suppression strategies for the Canadian supercritical water reactor concept

International Nuclear Information System (INIS)

McDonald, M.; Colton, A.; Pencer, J.

2015-01-01

The Canadian supercritical water-cooled reactor (SCWR) is a conceptual heavy water moderated, supercritical light water cooled pressure tube reactor. In contrast to current heavy water power reactors, the Canadian SCWR will be a batch fuelled reactor. Associated with batch fuelling is a large beginning-of-cycle excess reactivity. Furthermore, radial power peaking arising as a consequence of batch refuelling must be mitigated in some way. In this paper, burnable neutron absorber (BNA) added to fuel and absorbing rods inserted into the core are considered for reactivity management and power flattening. A combination of approaches appears adequate to reduce the core radial power peaking, while also providing reactivity suppression. (author)

Concept of safe tank-type water cooled and moderated reactor with HTGR microparticle fuel compacts

International Nuclear Information System (INIS)

Gol'tsev, A.O.; Kukharkin, N.E.; Mosevitskij, I.S.; Ponomarev-Stepnoj, N.N.; Popov, S.V.; Udyanskij, Yu.N.; Tsibul'skij, V.F.

1993-01-01

Concept of safe tank-type water-cooled and moderated reactor on the basis of HTGR fuel microparticles which enable to avoid environment contamination with radioactive products under severe accidents, is proposed. Results of neutron-physical and thermal-physical studies of water cooled and moderated reactor with HTGR microparticle compacts are presented. Characteristics of two reactors with thermal power of 500 and 1500 MW are indicated within the concept frames. The reactor behaviour under severe accident connected with complete loss of water coolant is considered. It is shown that under such an accident the fission products release from fuel microparticles does not occur

Heavy water reactors: Status and projected development. Part II. Final draft of a report to be published in the IAEA technical reports series. Working material

International Nuclear Information System (INIS)

2001-01-01

retains a low cost operational condition; to illustrate the short and medium term potential for design evolution of the heavy water reactor type; to describe the basis of economic competitiveness of the HWR, its resistance to severe cost increases and capability for extensive source localization; and to provide a reference document on HWRs and to help guide the activities of the IWG-HWR. Those organizations developing and operating HWRs recognize the potential for development of this line of reactors, and it is the intent of this document to illustrate that potential. Various countries and organizations in the past have explored a number of variants of heavy water reactors, and there is a desire to continue to explore some of these options in the future. Currently the pressurized heavy water cooled, heavy water moderated design is an economically competitive design and will likely continue to dominate the heavy water reactor type for some time. This document concentrates on heavy water moderated reactors for electricity production. Reactors for district heating and research reactors are not discussed, except where historical multi-purpose use was a rationale for developing the concept

Heavy water reactors: Status and projected development. Part I. Final draft of a report to be published in the IAEA technical reports series. Working material

International Nuclear Information System (INIS)

2001-01-01

retains a low cost operational condition; to illustrate the short and medium term potential for design evolution of the heavy water reactor type; to describe the basis of economic competitiveness of the HWR, its resistance to severe cost increases and capability for extensive source localization; and to provide a reference document on HWRs and to help guide the activities of the IWG-HWR. Those organizations developing and operating HWRs recognize the potential for development of this line of reactors, and it is the intent of this document to illustrate that potential. Various countries and organizations in the past have explored a number of variants of heavy water reactors, and there is a desire to continue to explore some of these options in the future. Currently the pressurized heavy water cooled, heavy water moderated design is an economically competitive design and will likely continue to dominate the heavy water reactor type for some time. This document concentrates on heavy water moderated reactors for electricity production. Reactors for district heating and research reactors are not discussed, except where historical multi-purpose use was a rationale for developing the concept

Pressure tube reactor

International Nuclear Information System (INIS)

Matsumoto, Tomoyuki; Fujino, Michihira.

1980-01-01

Purpose: To equalize heavy water flow distribution by providing a nozzle for externally injecting heavy water from a vibration preventive plate to the upper portion to feed the heavy water in a pressure tube reactor and swallowing up heavy water in a calandria tank to supply the heavy water to the reactor core above the vibration preventive plate. Constitution: A moderator injection nozzle is mounted on the inner wall of a calandria tank. Heavy water is externally injected above the vibration preventive plate, and heavy water in the calandria tank is swallowed up to supply the heavy water to the core reactor above the vibration preventive plate. Therefore, the heavy water flow distribution can be equalized over the entire reactor core, and the distribution of neutron absorber dissolved in the heavy water is equalized. (Yoshihara, H.)

Transmutation of Americium in Light and Heavy Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Hyland, B.; Dyck, G.R.; Edwards, G.W.R. [Chalk River Laboratories, Atomic Energy of Canada Limited (Canada); Ellis, R.J.; Gehin, J.C. [Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee (United States); Maldonado, G.I. [University of Tennessee (Knoxville)/ORNL, Tennessee (United States)

2009-06-15

There is interest worldwide in reducing the burden on geological nuclear fuel disposal sites. In most disposal scenarios the decay heat loading of the surrounding rock limits the capacity of these sites. On the long term, this decay heat is generated primarily by actinides, and a major contributor 100 to 1000 years after discharge from the reactor is {sup 241}Am. One possible approach to reducing the decay-heat burden is to reprocess spent reactor fuel and use thermal spectrum reactors to 'burn' the Am nuclides. The viability of this approach is dependent upon the detailed changes in chemical and isotopic composition of actinide-bearing fuels after irradiation in thermal reactor spectra. The currently available thermal spectrum reactor options include light water-reactors (LWRs) and heavy-water reactors (HWRs) such as the CANDU{sup R} designs. In addition, as a result of the recycle of spent LWR fuel, there would be a considerable amount of potential recycled uranium (RU). One proposed solution for the recycled uranium is to use it as fuel in Candu reactors. This paper investigates the possibilities of transmuting americium in 'spiked' bundles in pressurized water reactors (PWRs) and in boiling water reactors (BWRs). Transmutation of Am in Candu reactors is also examined. One scenario studies a full core fuelled with homogeneous bundles of Am mixed with recycled uranium, while a second scenario places Am in an inert matrix in target channels in a Candu reactor, with the rest of the reactor fuelled with RU. A comparison of the transmutation in LWRs and HWRs is made, in terms of the fraction of Am that is transmuted and the impact on the decay heat of the spent nuclear fuel. CANDU{sup R} is a registered trademark of Atomic Energy of Canada Limited (AECL). (authors)

Safety system in a heavy water detritiation plant

International Nuclear Information System (INIS)

Balteanu, O.; Stefan, I.; Retevoi, C.

2003-01-01

In a CANDU 6 type reactor a quantity of 55·10 15 Bq/year of tritium is generated, 95% being in the D 2 O moderator which can achieve a radioactivity of 2.5-3.5·10 12 Bq/kg. Tritium in heavy water contributes with 30-50% to the doses received by operation personnel and up to 20% to the radioactivity released in the environment. The large quantity of heavy water used in this type of reactors (500 tones) make storage very difficult, especially for environment. The extraction of tritium from tritiated heavy water of CANDU reactors solve the following problems: the radiation level in the operation area, the costs of maintenance and repair reduction due to reduction of personnel protection measures, the increase of NPP utilisation factor by shutdown time reduction for maintenance and repair, use the extracted tritium for fusion reactors and not for the last, lower costs and risk for storage heavy water waste. Heavy water detritiation methods, which currently are used in the industrial or experimental plant, are based on catalytic isotope exchange or electrolysis followed cryogenic distillation or permeation. The technology developed at Institute of Cryogenics and Isotope Separation is based upon catalytic exchange between tritiated water and deuterium, followed by cryogenic distillation of hydrogen isotopes. The nature of the fluids that are processed in detritiation requires the operation of the plant in safety conditions. The paper presents the safety system solution chose in order to solve this task, as well as a simulation of an incident and safety system response. The application software is using LabView platform that is specialised on control and factory automation applications. (author)

Numerical analysis and optimisation of heavy water upgrading column

International Nuclear Information System (INIS)

Sankar, Rama; Ghosh, Brindaban; Bhanja, K.

2013-01-01

In the 'Pressurised Heavy Water' type of reactors, heavy water is used both as moderator and coolant. During operation of reactor downgraded heavy water is generated that needs to be upgraded for reuse in the reactor. When the isotopic purity of heavy water becomes less than 99.75%, it is termed as downgraded heavy water. Downgraded heavy water also contains impurity such as corrosion products, dirt, oil etc. Upgradation of downgraded heavy water is normally done in two steps: (i) Purification: In this step downgraded heavy water is first purified to remove corrosion products, dirt, oil, etc. and (ii) Upgradation of heavy water to increase its isotopic purity, this step is carried out by vacuum distillation of downgraded heavy water after purification. This project is aimed at mathematical modelling and numerical simulation of heavy water upgrading column. Modelling and simulation studies of the upgradation column are based on equilibrium stage model to evaluate the effect of feed location, pressure, feed composition, reflux ratio in the packed column for given reboiler and condenser duty of distillation column. State to stage modelling of two-phase two-component flow has constitutes the overall modelling of the column. The governing equations consist of stage-wise species and overall mass continuity and stage-wise energy balance. This results in tridigonal matrix equation for stage liquid fractions for heavy and light water. The stage-wise liquid flow rates and temperatures are governed by stage-wise mass and energy balance. The combined form of the corresponding governing equations, with the incorporation of thermodynamic equation of states, form a system of nonlinear equations. This system have been resolved numerically using modified Newton-Raphson method. A code in the MATLAB platform has been developed by on above numerical procedure. The optimisation of the column operating conditions is to be carried out based on parametric studies and analysis of different

Topical papers on heavy water, fuel fabrication and reactors

International Nuclear Information System (INIS)

1978-01-01

A total of four papers is presented. The first contribution of the Federal Republic of Germany reviews the market situation for reactors and the relations between reactor producers and buyers as reflected in sales agreements. The second West German contribution gives a world-wide survey of fuel element production as well as of fuel and fuel element demand up to the year 2000. The Canadian paper discusses the future prospects of heavy-water production, while the Ecuador contribution deals with small and medium-sized nuclear power plants

Analysis of removal alternatives for the Heavy Water Components Test Reactor at the Savannah River Site. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Owen, M.B.

1997-04-01

This engineering study evaluates different alternatives for decontamination and decommissioning of the Heavy Water Components Test Reactor (HWCTR). Cooled and moderated with pressurized heavy water, this uranium-fueled nuclear reactor was designed to test fuel assemblies for heavy water power reactors. It was operated for this purpose from march of 1962 until December of 1964. Four alternatives studied in detail include: (1) dismantlement, in which all radioactive and hazardous contaminants would be removed, the containment dome dismantled and the property restored to a condition similar to its original preconstruction state; (2) partial dismantlement and interim safe storage, where radioactive equipment except for the reactor vessel and steam generators would be removed, along with hazardous materials, and the building sealed with remote monitoring equipment in place to permit limited inspections at five-year intervals; (3) conversion for beneficial reuse, in which most radioactive equipment and hazardous materials would be removed and the containment building converted to another use such as a storage facility for radioactive materials, and (4) entombment, which involves removing hazardous materials, filling the below-ground structure with concrete, removing the containment dome and pouring a concrete cap on the tomb. Also considered was safe storage, but this approach, which has, in effect, been followed for the past 30 years, did not warrant detailed evaluation. The four other alternatives were evaluate, taking into account factors such as potential effects on the environment, risks, effectiveness, ease of implementation and cost. The preferred alternative was determined to be dismantlement. This approach is recommended because it ranks highest in the comparative analysis, would serve as the best prototype for the site reactor decommissioning program and would be most compatible with site property reuse plans for the future.

Analysis of removal alternatives for the Heavy Water Components Test Reactor at the Savannah River Site. Revision 1

International Nuclear Information System (INIS)

Owen, M.B.

1997-04-01

This engineering study evaluates different alternatives for decontamination and decommissioning of the Heavy Water Components Test Reactor (HWCTR). Cooled and moderated with pressurized heavy water, this uranium-fueled nuclear reactor was designed to test fuel assemblies for heavy water power reactors. It was operated for this purpose from march of 1962 until December of 1964. Four alternatives studied in detail include: (1) dismantlement, in which all radioactive and hazardous contaminants would be removed, the containment dome dismantled and the property restored to a condition similar to its original preconstruction state; (2) partial dismantlement and interim safe storage, where radioactive equipment except for the reactor vessel and steam generators would be removed, along with hazardous materials, and the building sealed with remote monitoring equipment in place to permit limited inspections at five-year intervals; (3) conversion for beneficial reuse, in which most radioactive equipment and hazardous materials would be removed and the containment building converted to another use such as a storage facility for radioactive materials, and (4) entombment, which involves removing hazardous materials, filling the below-ground structure with concrete, removing the containment dome and pouring a concrete cap on the tomb. Also considered was safe storage, but this approach, which has, in effect, been followed for the past 30 years, did not warrant detailed evaluation. The four other alternatives were evaluate, taking into account factors such as potential effects on the environment, risks, effectiveness, ease of implementation and cost. The preferred alternative was determined to be dismantlement. This approach is recommended because it ranks highest in the comparative analysis, would serve as the best prototype for the site reactor decommissioning program and would be most compatible with site property reuse plans for the future

Parametric study of postulated reactivity transients due to ingress of heavy water from the reflector tank into the converted core of APSARA reactor

International Nuclear Information System (INIS)

Sankaranarayanan, S.

2004-01-01

Research reactors in the power range 5-10 MW with useable neutron flux values >1.OE+14 n/sqcm/sec can be constructed using LEU fuel with light water for neutron moderation and fuel cooling. In order to obtain a large irradiation volume, a heavy water reflector is used where fairly high neutron flux levels can be obtained. A prototype LEU fuelled 5/10 MW reactor design has been developed in the Bhabha Atomic Research Centre in Trombay. Work is on hand to carry out technology simulation of this reactor design by converting the pool type reactor APSARA in BARC. Presently the Apsara reactor uses MTh type high enriched U-Al alloy plate type fuel loaded in a 7x7 grid with a square lattice pitch of 76.8 mm. The reactor has three control-scram-shut off rods and one regulating control rod. In the first phase of the simulation studies, it is proposed to use the existing high enriched uranium fuel in a modified core with 37 positions arranged with a square lattice pitch of 84.8 mm, surrounded by a 50 cm thick heavy water reflector. Subsequently the converted core will use plate-type low enriched uranium suicide fuel. One of the accident scenarios postulated for the safety evaluation of the modified APSARA reactor is the reactivity transient due to the ingress of heavy water into the core through a small sized rupture in the aluminium wall of the reflector tank. Parametric analyses were done for the safety evaluation of modified Apsara reactor, for postulated leak of heavy water into the core from the reflector tank. A simplified computer code REDYN, based on point model reactor kinetics with one effective group of delayed neutrons is used for the analyses. Results of several parametric cases used in the study show that it is possible to contain the consequences of this type of reactivity transient within acceptable fuel and coolant thermal safety limits

Study of the heavy water regeneration processes

International Nuclear Information System (INIS)

Cavcic, E.

1965-11-01

Experience derived from heavy water reactor operation showed degradation and dilution of heavy water to be inevitable and depends on the type of reactor. Dilution of heavy water during operation of the RA and the RB reactors is shown in this report. Principles and procedures of heavy water regeneration by electrolysis, fractional distillation, cleaning, prevention of tritium contamination are described as well as separation columns

Technologies for tritium control in fission reactors moderated with heavy water; Tecnologias para control de tritio en reactores de fision moderados con agua pesada

Energy Technology Data Exchange (ETDEWEB)

Ramilo, L B; Gomez de Soler, S M [Comision Nacional de Energia Atomica, San Martin (Argentina). Unidad de Actividad Reactores y Centrales Nucleares

1997-12-31

This study was done within a program one of whose objectives was to analyze the possible strategies and technologies, to be applied to HWR at Argentine nuclear power plants, for tritium control. The high contribution of tritium to the total dose has given rise to the need by the operators and/or designers to carry out developments and improvements to try to optimize tritium control technologies. Within a tritium control program, only that one which includes the heavy water detritiation will allow to reduce the tritium concentrations at optimum levels for safety and cost-effective power plant operation. The technology chosen to be applied should depend not only on the technical feasibility but also on the analysis of economic and juncture factors such as, among others, the quantity of heavy water to be treated. It is the authors` belief that AECL tendency concerning heavy water treatment in its future reactors would be to employ the CECE technology complemented with immobilization on titanium beds, with the `on-line` detritiation in each nuclear power plant. This would not be of immediate application since our analysis suggests that AECL would assume that the process is under development and needs to be tested. (author). 21 refs.

Long-term scenarios of power reactors and fuel cycle development and the role of reduced moderation water reactors

International Nuclear Information System (INIS)

Sato, Osamu; Tatematsu, Kenji; Tanaka, Yoji

2000-01-01

Reduced moderation spectrum reactor is one of water cooled type reactors in future, which is based on the advanced technology of conventional nuclear power plants. The reduced moderation water reactor (RMWR) has various advantages, such as effective utilization of uranium resources, high conversion ratio, high burn-up, long-term cycle operation, and multiple recycle of plutonium. The RMWR is expected to be a substitute of fast breeder reactor (FBR) of which the development encounters with some technical and financial difficulties, and discontinues in many countries. The role of the RMWR on long-term scenarios of power reactor and fuel cycle development in Japan is investigated from the point of view of uranium resource needed. The consumption of natural uranium needed up to the year 2200 is calculated on various assumptions for the following three cases: (1) no breeder reactor; plutonium-thermal cycle in conventional light water reactor, (2) introduction of the FBR, and (3) introduction of the RMWR. The amounts of natural uranium consumption depends largely on the conversion ratio and plutonium quantity needed of a reactor type. The RMWR has a possibility as a substitute technology of the FBR with the improvement of conversion ratio and high burn-up. (Suetake, M.)

Long-term scenarios of power reactors and fuel cycle development and the role of reduced moderation water reactors

Energy Technology Data Exchange (ETDEWEB)

Sato, Osamu; Tatematsu, Kenji; Tanaka, Yoji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2000-06-01

Reduced moderation spectrum reactor is one of water cooled type reactors in future, which is based on the advanced technology of conventional nuclear power plants. The reduced moderation water reactor (RMWR) has various advantages, such as effective utilization of uranium resources, high conversion ratio, high burn-up, long-term cycle operation, and multiple recycle of plutonium. The RMWR is expected to be a substitute of fast breeder reactor (FBR) of which the development encounters with some technical and financial difficulties, and discontinues in many countries. The role of the RMWR on long-term scenarios of power reactor and fuel cycle development in Japan is investigated from the point of view of uranium resource needed. The consumption of natural uranium needed up to the year 2200 is calculated on various assumptions for the following three cases: (1) no breeder reactor; plutonium-thermal cycle in conventional light water reactor, (2) introduction of the FBR, and (3) introduction of the RMWR. The amounts of natural uranium consumption depends largely on the conversion ratio and plutonium quantity needed of a reactor type. The RMWR has a possibility as a substitute technology of the FBR with the improvement of conversion ratio and high burn-up. (Suetake, M.)

Nuclear reactor types

International Nuclear Information System (INIS)

Jones, P.M.S.

1987-01-01

The characteristics of different reactor types designed to exploit controlled fission reactions are explained. Reactors vary from low power research devices to high power devices especially designed to produce heat, either for direct use or to produce steam to drive turbines to generate electricity or propel ships. A general outline of basic reactors (thermal and fast) is given and then the different designs considered. The first are gas cooled, including the Magnox reactors (a list of UK Magnox stations and reactor performance is given), advanced gas cooled reactors (a list of UK AGRs is given) and the high temperature reactor. Light water cooled reactors (pressurized water [PWR] and boiling water [BWR] reactors) are considered next. Heavy water reactors are explained and listed. The pressurized heavy water reactors (including CANDU type reactors), boiling light water, steam generating heavy water reactors and gas cooled heavy water reactors all come into this category. Fast reactors (liquid metal fast breeder reactors and gas cooled fast reactors) and then water-cooled graphite-moderated reactors (RBMK) (the type at Chernobyl-4) are discussed. (U.K.)

Nuclear power reactors

International Nuclear Information System (INIS)

1982-11-01

After an introduction and general explanation of nuclear power the following reactor types are described: magnox thermal reactor; advanced gas-cooled reactor (AGR); pressurised water reactor (PWR); fast reactors (sodium cooled); boiling water reactor (BWR); CANDU thermal reactor; steam generating heavy water reactor (SGHWR); high temperature reactor (HTR); Leningrad (RMBK) type water-cooled graphite moderated reactor. (U.K.)

Feasibility study on the thorium fueled boiling water breeder reactor

International Nuclear Information System (INIS)

PetrusTakaki, N.

2012-01-01

The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

CANDU - Canadian experience and expectations with the heavy-water reactor

International Nuclear Information System (INIS)

Foster, J.S.; Russell, S.H.

1977-05-01

The paper describes the evolution of the CANDU nuclear-power plants with particular reference to the objectives of safety, reliability and economy; the development of industrial capacity for the supply of fuel, components and heavy water; and the prospective development of advanced fuel cycles and the projected results. It provides data on radiation, releases, and exposures, internal and external to the power plants; plant availability, capacity factors and other performance data; heavy water production data with reference to safety, reliability, and economics; projections of the performance of CANDU reactors operating on a thorium-U-233 cycle and the development required to establish this cycle; and intent with respct to spent-fuel management and radioactive-waste storage. (author)

Heavy water reactors on the once-through uranium cycle

International Nuclear Information System (INIS)

1978-05-01

This paper presents preliminary technical and economic data to INFCE on the once-through uranium fuel cycle for use in early comparisons of alternate nuclear systems. The denatured thorium fuel cycle is discussed in a companion paper. Information for this paper was developed under an ongoing program, and more complete reporting of the evaluation of the heavy water reactor and its fuel cycles is planned toward the end of the year

Measurement of the heavy water level in the fuel channels of the RA reactor - Annex 11

International Nuclear Information System (INIS)

Nikolic, M.

1964-01-01

The objective of measuring the heavy water level in the reactor channels was to verify experimentally the possibilities of reactor cooling with parallel operation of heavy water pumps od 1500 rotations/min at nominal power of 6.5 MW. Measurements were done in 2 periphery and 2 central fuel channels with pumps speed 1500, 1800 and 3000 rotations/min by a contact probe with electric resistance measuring device. precision of the measurement was ±1 cm

Transmutation of Tc-99 in fission reactors

International Nuclear Information System (INIS)

Kloosterman, J.L.; Li, J.M.

1994-12-01

Transmutation of Tc-99 in three different types of fission reactors is considered: A heavy water reactor, a fast reactor and a light water reactor. For the first type a CANDU reactor was chosen, for the second one the Superphenix reactor, and for the third one a PWR. The three most promising Tc-99 transmuters are the fast reactor with a moderated subassembly in the inner core, a fast reactor with a non-moderated subassembly in the inner core, and a heavy water reactor with Tc-99 target pins in the moderator between the fuel bundles. Transmutation half lives of 15 to 25 years can be achieved, with yearly transmuted Tc-99 masses of about 100 kg at a thermal reactor power of about 3000 MW. (orig.)

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

International Nuclear Information System (INIS)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J.

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e aq - , ·OD and ·D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 o C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

Energy Technology Data Exchange (ETDEWEB)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e{sub aq}{sup -}, {center_dot}OD and {center_dot}D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 {sup o}C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

Opinion about difficulties of RA reactor operation under conditions of high activity of the heavy water system - Annex 2

International Nuclear Information System (INIS)

Nikolic, M.

1963-01-01

It was concluded that reactor the reactor operation is very dangerous for the reactor installation as well as safety of the staff under conditions of heavy water increased activity. Two fundamental arguments in favour of this conclusion are: insufficient possibility of reactor components inspection during maintenance and operation in the future period; difficulties in prevention of accidents that could occur is equally dangerous for the reactor facility and the environment. Cleaning and decontamination of the complete heavy water system is needed before the reactor operation starts in order to avoid possible failures or accidental events [sr

Experimental estimation of moderator temperature coefficient of reactivity of the IPEN/MB-01 research reactor

International Nuclear Information System (INIS)

Silva, Rubens C. da; Bitelli, Ulysses D.; Mura, Luiz Ernesto C.

2017-01-01

The aim of this article is to present the procedure for the experimental estimation of the Moderator Temperature Coefficient of Reactivity of the IPEN/MB-01 Research Reactor, a parameter that has an important role in the physics and the control operations of any reactor facility. At the experiment, the IPEN/MB-01 reactor went critical at the power of 1W (1% of its total power), and whose core configuration was 28 x 26 rectangular array of UO_2 fuel rods, inside a light water (moderator) tank. In addition, there was a heavy water (D_2O) reflector installed in the West side of the core to obtain an adequate neutron reflection along the experiment. The moderator temperature was increased in steps of 4 °C, and the measurement of the mean moderator temperature was acquired using twelve calibrated thermocouples, placed around the reactor core. As a result, the mean value of -4.81 pcm/°C was obtained for such coefficient. The curves of ρ(T) (Reactivity x Temperature) and α"M_T(T)(Moderator Temperature Coefficient of Reactivity x Temperature) were developed using data from an experimental measurement of the integral reactivity curves through the Stable Period and Inverse Kinetics Methods, that was carried out at the reactor with the same core configuration. Such curves were compared and showed a very similar behavior between them. (author)

Deuterium and heavy water

International Nuclear Information System (INIS)

Vasaru, G.; Ursu, D.; Mihaila, A.; Szentgyorgyi, P.

1975-01-01

This bibliography on deuterium and heavy water contains 3763 references (1932-1974) from 43 sources of information. An author index and a subject index are given. The latter contains a list of 136 subjects, arranged in 13 main topics: abundance of deuterium , catalysts, catalytic exchange, chemical equilibria, chemical kinetics, deuterium and heavy water analysis, deuterium and heavy water properties, deuterium and heavy water separation, exchange reactions, general review, heavy water as moderator, isotope effects, synthesis of deuterium compounds

Core construction in a pressure tube type heavy water reactor

International Nuclear Information System (INIS)

Ueda, Makoto; Aoki, Katsutada.

1975-01-01

Object: To replace a centrally positioned fuel assembly of a fuel assembly unit with a reactor controlling machinery to decrease a distance between the fuel assemblies thereby saving use of heavy water and enhancing economy. Structure: A centrally positioned fuel assembly of a fuel assembly unit, which is composed of a plurality of fuel assemblies orderly arranged in lattice fashion, is replaced with a reactor controlling members such as control rods, poison tubes and the like to provide an arrangement of lattice-free type fuel assembly, thus reducing the pitch as small as possible. (Kamimura, M.)

Enrichment reduction calculations for the DIDO reactor. App. B

International Nuclear Information System (INIS)

Constantine, G.; Javadi, M.; Thick, E.

1985-01-01

The possibility has been raised that DIDO/PLUTO type heavy water moderated reactors can be operated with fuel of lower than the 75% enrichment material currently in use with the object of increasing the proliferation resistance of the fuel cycle. This paper sets out to examine the reactor physics aspects of enrichment reductions to 45% and 20% for Harwell's MTR's as part of an IAEA collaborative exercise currently being conducted to examine the topic in a more general way for the whole class of heavy water moderated reactors. The reactor physics tool used at Harwell is WIMSE, the Winfrith Improved Multigroup Scheme, a suite of linked reactor physics codes which has been used extensively for light water, heavy water and graphite moderated thermal reactors. The course of the calculations and the WIMSE modules involved in this study are described briefly

Core design study on reduced-moderation water reactors

International Nuclear Information System (INIS)

Hiroshi, Akie; Yoshihiro, Nakano; Toshihisa, Shirakawa; Tsutomu, Okubo; Takamichi, Iwamura

2002-01-01

The conceptual core design study of reduced-moderation water reactors (RMWRs) with tight-pitched MOX-fuelled lattice has been carried out at JAERI. Several different RMWR core concepts based on both BWR and PWR have been proposed. All the core concepts meet with the aim to achieve both a conversion ratio of 1.0 or larger and negative void reactivity coefficient. As one of these RMWR concepts, the ABWR compatible core is also proposed. Although the conversion ratio of this core is 1.0 and the void coefficient is negative, the discharge burn-up of the fuel was about 25 GWd/t. By adopting a triangular fuel pin lattice for the reduction of moderator volume fraction and modifying axial Pu enrichment distribution, it was aimed to extend the discharge burn-up of ABWR compatible type RMWR. By using a triangular fuel lattice of smaller moderator volume fraction, discharge burn-up of 40 GWd/t seems achievable, keeping the high conversion ratio and the negative void coefficient. (authors)

Advanced concept of reduced-moderation water reactor (RMWR) for plutonium multiple recycling

International Nuclear Information System (INIS)

Okubo, T.; Iwamura, T.; Takeda, R.; Yamamoto, K.; Okada, H.

2001-01-01

An advanced water-cooled reactor concept named the Reduced-Moderation Water Reactor (RMWR) has been proposed to attain a high conversion ratio more than 1.0 and to achieve the negative void reactivity coefficient. At present, several types of design concepts satisfying both the design targets have been proposed based on the evaluation for the fuel without fission products and minor actinides. In this paper, the feasibility of the RMWR core is investigated for the plutonium multiple recycling under advanced reprocessing schemes with low decontamination factors as proposed for the FBR fuel cycle. (author)

Manufacture and installation of reactor auxiliary facilities for advanced thermal prototype reactor 'Fugen'

International Nuclear Information System (INIS)

Kawahara, Toshio; Matsushita, Tadashi

1977-01-01

The facilities of reactor auxiliary systems for the advanced thermal prtotype reactor ''Fugen'' were manufactured in factories since 1972, and the installation at the site began in November, 1974. It was almost completed in March, 1977, except a part of the tests and inspections, therefore the outline of the works is reported. The ATR ''Fugen'' is a heavy water-moderated, boiling light water reactor, and its reactor auxiliary systems comprise mainly the facilities for handling heavy water, such as heavy water cooling system, heavy water cleaning system, poison supplying system, helium circulating system, helium cleaning system, and carbon dioxide system. The poison supplying system supplies liquid poison to the heavy water cooling system to absorb excess reactivity in the initial reactor core. The helium circulating system covers heavy water surface with helium to prevent the deterioration of heavy water and maintains heavy water level by pressure difference. The carbon dioxide system flows highly pure CO 2 gas in the space of pressure tubes and carandria tubes, and provides thermal shielding. The design, manufacture and installation of the facilities of reactor auxiliary systems, and the helium leak test, synthetic pressure test and total cleaning are explained. (Kako, I.)

Heavy water: a distinctive and essential component of CANDU

International Nuclear Information System (INIS)

Miller, A.I.; van Alstyne, H.M.

1994-06-01

The exceptional properties of heavy water as a neutron moderator provide one of the distinctive features of CANDU reactors. Although most of the chemical and physical properties of deuterium and protium (mass 1 hydrogen) are appreciably different, the low terrestrial abundance of deuterium makes the separation of heavy water a relatively costly process, and so of considerable importance to the CANDU system. World heavy-water supplies are currently provided by the Girdler-Sulphide process or processes based on ammonia-hydrogen exchange. Due to cost and hazard considerations, new processes will be required for the production of heavy water in and beyond the next decade. Through AECL's development and refinement of wetproofed catalysts for the exchange of hydrogen isotopes between water and hydrogen, a family of new processes is expected to be deployed. Two monothermal processes, CECE (Combined Electrolysis and Catalytic Exchange, using water-to-hydrogen conversion by electrolysis) and CIRCE (Combined Industrially Reformed hydrogen and Catalytic Exchange, based on steam reforming of hydrocarbons), are furthest advanced. Besides its use for heavy-water production, the CECE process is a highly effective technology for heavy-water upgrading and for tritium separation from heavy (or light) water. (author). 10 refs., 1 tab., 7 figs

Implications of alpha-decay for long term storage of advanced heavy water reactor fuels

International Nuclear Information System (INIS)

Pencer, J.; McDonald, M.H.; Roubtsov, D.; Edwards, G.W.R.

2017-01-01

Highlights: •Alpha decays versus storage time are calculated for examples of advanced heavy water reactor fuels. •Estimates are made for fuel swelling and helium bubble formation as a function of time. •These predictions are compared to predictions for natural uranium fuel. •Higher rates of damage are predicted for advanced heavy water reactor fuels than natural uranium. -- Abstract: The decay of actinides such as 238 Pu, results in recoil damage and helium production in spent nuclear fuels. The extent of the damage depends on storage time and spent fuel composition and has implications for the integrity of the fuels. Some advanced nuclear fuels intended for use in pressurized heavy water pressure tube reactors have high initial plutonium content and are anticipated to exhibit swelling and embrittlement, and to accumulate helium bubbles over storage times as short as hundreds of years. Calculations are performed to provide estimates of helium production and fuel swelling associated with alpha decay as a function of storage time. Significant differences are observed between predicted aging characteristics of natural uranium and the advanced fuels, including increased helium concentrations and accelerated fuel swelling in the latter. Implications of these observations for long term storage of advanced fuels are discussed.

Investigation of the heavy water distillation system at the RA reactor; Ispitivanje sistema za destilaciju teske vode reaktora RA

Energy Technology Data Exchange (ETDEWEB)

Zecevic, V; Badrljica, R [Institute of Nuclear Sciences Boris Kidric, Reaktor RA, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

The heavy water distillation system was tested because this was not done before the reactor start-up. Detailed inspection of the system components showed satisfactory results. Leak testing was done as well as the testing of the instrumentation which enables reliable performance of the system. Performance testing was done with ordinary water and later 2700 l of heavy water from the reactor was purified, decreasing the activity by 45%.

Nuclear reactors. Introduction

International Nuclear Information System (INIS)

Boiron, P.

1997-01-01

This paper is an introduction to the 'nuclear reactors' volume of the Engineers Techniques collection. It gives a general presentation of the different articles of the volume which deal with: the physical basis (neutron physics and ionizing radiations-matter interactions, neutron moderation and diffusion), the basic concepts and functioning of nuclear reactors (possible fuel-moderator-coolant-structure combinations, research and materials testing reactors, reactors theory and neutron characteristics, neutron calculations for reactor cores, thermo-hydraulics, fluid-structure interactions and thermomechanical behaviour of fuels in PWRs and fast breeder reactors, thermal and mechanical effects on reactors structure), the industrial reactors (light water, pressurized water, boiling water, graphite moderated, fast breeder, high temperature and heavy water reactors), and the technology of PWRs (conceiving and building rules, nuclear parks and safety, reactor components and site selection). (J.S.)

Measurement of concentration of heavy water

International Nuclear Information System (INIS)

Tsukamoto, Yuichi; Kondo, Mitsuo; Sakurai, Naoyuki

1979-01-01

The concentration of heavy water is measured as one of the technical management in the Fugen plant. The heavy water is used as the moderator in the reactor. The measuring method depends on the theory of light absorption. The light absorption range of heavy water spreads from near infrared to infrared zone. The near infrared absorption was adopted for the purpose, as the absorption is much larger in infrared zone, and the measurement has to be conducted, limiting the apparent absorption. This measuring method is available to determine the concentration of heavy water in the broad range exactly. The preparation of heavy water sample and the measurement of the absorption spectra of near infrared ray are explained, as the experimental procedure. The sample cell was made of quartz, and the spectroscope was the Hitachi 323 type. The resolving power is 100 nm and 27 nm for the wave length of 1000 nm and 2500 nm, respectively. Concerning the measured results, the absorption was recorded in the wave length range from 600 nm to 2600 nm, and for the heavy water concentration range from 0 to 99.77 wt. %. The peaks of absorption were located at the wave length of 1450, 1660, 1920, 1970, 2020 and 2600 nm. The three kinds of fundamental vibration mode of the molecules of both light and heavy water are shown, and the peaks belong to H 2 O, HDO and D 2 O, respectively. The relation between the absorption and the heavy water concentration, and that between the transmissivity and the wave length are shown, when the cell thickness was varied to 5 mm and 20 mm, and the heavy water concentration to 21%, 62% and 99.85%. (Nakai, Y.)

Thermophysical properties database of materials for light water reactors and heavy water reactors. Final report of a coordinated research project 1999-2005

International Nuclear Information System (INIS)

2006-06-01

The IAEA Coordinated Research Project (CRP) on the Establishment of a Thermo-physical Properties Database for Light Water Reactors (LWRs) and Heavy Water Reactors (HWRs) started in 1999. It was included in the IAEA's Nuclear Power Programme following endorsement in 1997 by the IAEA's Technical Working Groups on Advanced Technologies for LWRs and HWRs (the TWG-LWR and the TWG-HWR). Furthermore, the TWG on Fuel Performance and Technology (TWG-FPT) also expressed its support. This CRP was conducted as a joint task within the IAEA's project on technology development for LWRs and HWRs in its nuclear power programme. Improving the technology for nuclear reactors through better computer codes and more accurate materials property data can contribute to improved economics of future plants by helping to remove the need for large design margins, which are currently used to account for limitations of data and methods. Accurate representations of thermo-physical properties under relevant temperature and neutron fluence conditions are necessary for evaluating reactor performance under normal operation and accident conditions. The objective of this CRP was to collect and systematize a thermo-physical properties database for light and heavy water reactor materials under normal operating, transient and accident conditions and to foster the exchange of non-proprietary information on thermo-physical properties of LWR and HWR materials. An internationally available, peer reviewed database of properties at normal and severe accident conditions has been established on the Internet. This report is intended to serve as a useful source of information on thermo-physical properties data for water cooled reactor analyses. The properties data have been initially stored in the THERSYST data system at the University of Stuttgart, Germany, which was subsequently developed into an internationally available Internet database named THERPRO at Hanyang University, Republic of Korea

Experience in the development of metal uranium-base nuclear fuel for heavy-water gas-cooled reactors

International Nuclear Information System (INIS)

Ashikhmin, V.P.; Vorob'ev, M.A.; Gusarov, M.S.; Davidenko, A.S.; Zelenskij, V.F.; Ivanov, V.E.; Krasnorutskij, V.S.; Petel'guzov, I.A.; Stukalov, A.I.

1978-01-01

Investigations were carried out to solve the problem of making the development of radiation-resistant uranium fuel for power reactors including the heavy-water gas-cooled KS-150 reactor. Factors are considered that limit the lifetime of uranium fuel elements, and the ways of suppressing them are discussed. Possible reasons of the insufficient radiation resistance of uranium rod fuel element and the progress attained are analyzed. Some general problems on the fuel manufacture processes are discussed. The main results are presented on the operation of the developed fuel in research reactor loops and the commercial heavy-water KS-150 reactor. The results confirm an exceptionally high radiation resistance of fuel to burn-ups of 1.5-2%. The successful solution of a large number of problems associated with the development of metal uranium fuel provides for new possibilities of using metal uranium in power reactors

Study of essential safety features of a three-loop 1,000 MWe light water reactor (PWR) and a corresponding heavy water reactor (HWR) on the basis of the IAEA nuclear safety standards

International Nuclear Information System (INIS)

1989-02-01

Based on the IAEA Standards, essential safety aspects of a three-loop pressurized water reactor (1,000 MWe) and a corresponding heavy water reactor were studied by the TUeV Baden e.V. in cooperation with the Gabinete de Proteccao e Seguranca Nuclear, a department of the Ministry which is responsible for Nuclear power plants in Portugal. As the fundamental principles of this study the design data for the light water reactor and the heavy water reactor provided in the safety analysis reports (KWU-SSAR for the 1,000 MWe PWR, KWU-PSAR Nuclear Power Plant ATUCHA II) are used. The assessment of the two different reactor types based on the IAEA Nuclear Safety Standards shows that the reactor plants designed according to the data given in the safety analysis reports of the plant manufacturer meet the design requirements laid down in the pertinent IAEA Standards. (orig.) [de

Experimental estimation of moderator temperature coefficient of reactivity of the IPEN/MB-01 research reactor

Energy Technology Data Exchange (ETDEWEB)

Silva, Rubens C. da; Bitelli, Ulysses D.; Mura, Luiz Ernesto C., E-mail: rubensrcs@usp.br, E-mail: ubitelli@ipen.br, E-mail: credidiomura@gmail.com [Universidade de Sao Paulo (PNV/POLI/USP), SP (Brazil). Arquitetura Naval e Departamento de Engenharia Oceanica; Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2017-07-01

The aim of this article is to present the procedure for the experimental estimation of the Moderator Temperature Coefficient of Reactivity of the IPEN/MB-01 Research Reactor, a parameter that has an important role in the physics and the control operations of any reactor facility. At the experiment, the IPEN/MB-01 reactor went critical at the power of 1W (1% of its total power), and whose core configuration was 28 x 26 rectangular array of UO{sub 2} fuel rods, inside a light water (moderator) tank. In addition, there was a heavy water (D{sub 2}O) reflector installed in the West side of the core to obtain an adequate neutron reflection along the experiment. The moderator temperature was increased in steps of 4 °C, and the measurement of the mean moderator temperature was acquired using twelve calibrated thermocouples, placed around the reactor core. As a result, the mean value of -4.81 pcm/°C was obtained for such coefficient. The curves of ρ(T) (Reactivity x Temperature) and α{sup M}{sub T}(T)(Moderator Temperature Coefficient of Reactivity x Temperature) were developed using data from an experimental measurement of the integral reactivity curves through the Stable Period and Inverse Kinetics Methods, that was carried out at the reactor with the same core configuration. Such curves were compared and showed a very similar behavior between them. (author)

The importance of heavy water in nuclear technology

International Nuclear Information System (INIS)

Gharib, A.G.

2004-01-01

Due to similarities of chemical and almost physical properties in H 2 O and D 2 O but differences in nuclear and particle peculiarities provide valuable application for D 2 O. To sustain a controlled chain reaction, the energy of neutrons produced by fission must be reduced through collisions with other nuclei, a process called moderation. A good moderator has a mass close to that of the neutron to maximize energy loss per collision and a very small neutron capture cross section to minimize unwanted nuclear reactions. Deuterium is far the best moderator, more than 80 times better than hydrogen and 30 times better than 12 C ir 18 O. Heavy water is almost as good as deuterium and has the distinct advantage of being a nonflammable liquid. Heavy water is also an excellent neutron reflector, and thus decreases the number of neutrons that escape the reactor core without participating in fission reactions. For this reason a feasibility study and subsequently a technical survey was carried out on engineering of a pilot scale plant. As the result of this studies, the know-how of heavy water production on basis of selected method including dual temperature isotopic exchange and distillation techniques developed. Subsequently the primary and almost detail engineering documents prepared on best knowledge of our own engineers without external contribution

Detection of heavy-water leaks in nuclear reactors : a novel method

International Nuclear Information System (INIS)

Murthy, M.S.; Gor, M.K.

2002-01-01

Technical Physics and Prototype Engineering Division, BARC has designed, developed and produced several high sensitivity mass spectrometer helium leak detectors over a period of two decades. Sometimes back, when there was a problem of detecting heavy water leaks in situ in one of the nuclear power reactors of the Department of Atomic Energy, it was referred to this division for a technical solution. After discussing with the site engineers, the various problems involved in the on-line detection of heavy water leaks especially near the end fittings of the coolant assemblies, a novel method of leak detection was developed. Some of the salient features of the method and the results obtained in the laboratory tests are given in this paper. (author)

The supply of steam from Candu reactors for heavy water production

International Nuclear Information System (INIS)

Robertson, R.F.S.

1975-09-01

By 1980, Canada's energy needs for D 2 O production will be 420 MW of electrical energy and 3600 MW of thermal energy (as steam). The nature of the process demands that this energy supply be exceptionally stable. Today, production plants are located at or close to nuclear electricity generating sites where advantage can be taken of the low cost of both the electricity and steam produced by nuclear reactors. Reliability of energy supply is achieved by dividing the load between the multiple units which comprise the sites. The present and proposed means of energy supply to the production sites at the Bruce Heavy Water Plant in Ontario and the La Prade Heavy Water Plant in Quebec are described. (author)

Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This practice covers procedures for designing a surveillance program for monitoring the radiation-induced changes in the mechanical properties of ferritic materials in light-water moderated nuclear power reactor vessels. This practice includes the minimum requirements for the design of a surveillance program, selection of vessel material to be included, and the initial schedule for evaluation of materials. 1.2 This practice was developed for all light-water moderated nuclear power reactor vessels for which the predicted maximum fast neutron fluence (E > 1 MeV) at the end of license (EOL) exceeds 1 × 1021 neutrons/m2 (1 × 1017 n/cm2) at the inside surface of the reactor vessel. 1.3 This practice applies only to the planning and design of surveillance programs for reactor vessels designed and built after the effective date of this practice. Previous versions of Practice E185 apply to earlier reactor vessels. 1.4 This practice does not provide specific procedures for monitoring the radiation induced cha...

Enhancement of efficacy of process water monitors in detecting heavy water leak in steam generator blow down lines

International Nuclear Information System (INIS)

Mitra, S.R.; Kohale, S.D.; Parida, B.K.; Gathe, G.D.; Pati, C.K.; Mudgal, B.K.; Niraj; Pawar, S.K.

2006-01-01

The Steam Generator (SG) serves as an interface between primary and secondary cycle in Pressurized Heavy Water Reactor (PHWR). Failure of steam generator tubes result in leaking of active heavy water in the secondary closed loop. In Tarapur Atomic Power Station-3 and 4 (TAPS- 3 and 4), Scintillator detectors are provided to detect on line heavy water leakages in SG and moderator heat exchangers by monitoring Nitrogen-16 ( 16 N) and Oxygen-19 ( 19 O) activities. Efficacy of detection of these activities at designed detector position on SG blow down line in presence of background radiation field is analysed theoretically. The count rate of 19 O and 16 N estimated at the detector position inside Reactor Building (RB) shows that detectors only respond to very high leak rates due to presence of high ambient radiation level even though sensitivity is appreciably good. For detector position in RB in the accessible areas and out side the RE containment, the travel time for the blow down feed water becomes moderately and very long respectively resulting in poor sensitivity. However the results show that wherever background levels is low, the efficacy of leak detection becomes considerably better than the results obtained when detector is placed inside RB. The study was validated during the reactor operation by recording the detector count rates due to prevalent ambient radiation level near to the detectors. Subsequently the detectors were relocated in an area inside RB where relocation was feasible, travel time of the blow down feed water was moderate and the area had an relatively low ambient radiation level. This paper discusses the methodology adopted during the study and results obtained during theoretical estimation and practical validation. (author)

Nuclear reactor, reactor core thereof, and device for constituting the reactor

International Nuclear Information System (INIS)

Takiyama, Masashi.

1994-01-01

A reactor core is constituted by charging coolants (light water) in a reactor pressure vessel and distributing fuel assemblies, reflecting material sealing pipes, moderator (heavy water and helium gas) sealing pipes, and gas sealing pipes therein. A fuel guide tube is surrounded by a cap and the gap therebetween is made hollow and filled with coolant steams. The cap is supported by a baffle plate. The moderator sealing pipe is disposed in a flow channel of coolants in adjacent with the cap. The position of the moderator sealing tube in the reactor core is controlled by water stream from a hydraulic pump with a guide tube extending below the baffle plate being as a guide. Then, the position of the moderator sealing tube is varied to conduct power control, burnup degree compensation, and reactor shut down. With such procedures, moderator cooling facility is no more necessary to simplify the structure. Further, heat generated from the moderator is transferred to the coolants thereby improving heat efficiency of the reactor. (I.N.)

HAZOP-study on heavy water research reactor primary cooling system

International Nuclear Information System (INIS)

Hashemi-Tilehnoee, M.; Pazirandeh, A.; Tashakor, S.

2010-01-01

By knowledge-based Hazard and Operability (HAZOP) technique, equipment malfunction and deficiencies in the primary cooling system of the generic heavy water research reactor are studied. This technique is used to identify the representative accident scenarios. The related Process Flow Drawing (PFD) is prepared as our study database for this plant. Since this facility is in the design stage, applying the results of HAZOP-study to PFD improves the safety of the plant.

Flooding of a large, passive, pressure-tube light water reactor

International Nuclear Information System (INIS)

Hejzlar, P.; Todreas, N.E.; Driscoll, M.J.

1997-01-01

A reactor concept has been developed which can survive loss of coolant accidents without scram and without replenishing primary coolant inventory, while maintaining safe temperature limits on the fuel and pressure tubes. The proposed concept is a pressure tube type reactor of similar design to CANDU reactors, but differing in three key aspects. First, a solid SiC-coated graphite fuel matrix is used in place of fuel pin bundles to enable the dissipation of decay heat from the fuel in the absence of primary coolant. Second, the heavy water coolant in the pressure tubes is replaced by light water, which also serves as the moderator. Finally, the calandria tank, surrounded by a graphite reflector, contains a low pressure gas instead of heavy water moderator, and this normally-voided calandria is connected to a light water heat sink. The cover gas displaces the light water from the calandria during normal operation, while during loss of coolant or loss of heat sink accidents it allows passive calandria flooding. Calandria flooding also provides redundant and diverse reactor shutdown. This paper describes the thermal hydraulic characteristics of the passively initiated, gravity driven calandria flooding process. Flooding the calandria space with light water is a unique and very important feature of the proposed pressure-tube light water reactor (PTLWR) concept. The flooding of the top row of fuel channels must be accomplished fast enough so that in the total loss of coolant, none of the critical components of the fuel channel, i.e. the pressure tube, the calandria tube, the matrix and the fuel, exceed their design limits. The flooding process has been modeled and shown to be rapid enough to maintain all components within their design limits. (orig.)

Determination of the tritium content in the reactor heavy water; Odredjivanje porasta kolicine tritijuma u reaktorskoj teskoj vodi

Energy Technology Data Exchange (ETDEWEB)

Ribnikar, S [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-01-15

Quantity of tritium was measured in the heavy water, in the heavy water vapour and radiolyzed deuterium from the helium cover gas of the RA reactor. It has been shown that isotopic equilibrium D{sub 2}O+DT{r_reversible}DTO+D{sub 2} exists and that it is catalyzed by irradiation. Small quantities of ammonium in the reactor cover gas are inhibiting the migration of tritium from the heavy water. Izmerena ja sadrzina tritijuma u tecnoj teskoj vodi, njenoj pari i radiolizovanom deuterijumu iz helijumske atmosfere reaktora RA. Pokazano je da postoji izotopska ravnoteza D{sub 2}O+DT{r_reversible}DTO+D{sub 2}, koja je katalizovana zracenjem. Male kolicine amonijaka reaktorske atmosfere deluju u smislu otezavanja migracije tritijuma iz teske vode (author)

Lattice cell and full core physics of internally cooled annular fuel in heavy water moderated reactors

Energy Technology Data Exchange (ETDEWEB)

Armstrong, J.; Hamilton, H.; Hyland, B. [Atomic Energy of Canada Limited, Chalk River Laboratories, Chalk River, Ontario, K0J 1J0 (Canada)

2013-07-01

A program is underway at Atomic Energy of Canada Limited (AECL) to develop a new fuel bundle concept to enable greater burnups for PT-HWR (pressure tube heavy water reactor) cores. One option that AECL is investigating is an internally cooled annular fuel (ICAF) element concept. ICAF contains annular cylindrical pellets with cladding on the inner and outer diameters. Coolant flows along the outside of the element and through the centre. With such a concept, the maximum fuel temperature as a function of linear element rating is significantly reduced compared to conventional, solid-rod type fuel. The preliminary ICAF bundle concept considered in this study contains 24 half-metre long internally cooled annular fuel elements and one non-fuelled centre pin. The introduction of the non-fuelled centre pin reduces the coolant void reactivity (CVR), which is the increase in reactivity that occurs on voiding the coolant in accident scenarios. Lattice cell and full core physics calculations of the preliminary ICAF fuel bundle concept have been performed for medium burnups of approximately 18 GWd/tU using WIMS-AECL and reactor fuel simulation program (RFSP). The results will be used to assist in concept configuration optimization. The effects of radial and axial core power distributions, linear element power ratings, refuelling rates and operational power ramps have been analyzed. The results suggest that burnups of greater than 18 GWd/tU can be achieved in current reactor designs. At approximately 18 GWd/tU, expected maximum linear element ratings in a PT-HWR with online-refuelling are approximately 90 kW/m. These conditions would be prohibitive for solid-rod fuel, but may be possible in ICAF fuel given the reduced maximum fuel temperature as a function of linear element rating. (authors)

Lattice cell and full core physics of internally cooled annular fuel in heavy water moderated reactors

International Nuclear Information System (INIS)

Armstrong, J.; Hamilton, H.; Hyland, B.

2013-01-01

A program is underway at Atomic Energy of Canada Limited (AECL) to develop a new fuel bundle concept to enable greater burnups for PT-HWR (pressure tube heavy water reactor) cores. One option that AECL is investigating is an internally cooled annular fuel (ICAF) element concept. ICAF contains annular cylindrical pellets with cladding on the inner and outer diameters. Coolant flows along the outside of the element and through the centre. With such a concept, the maximum fuel temperature as a function of linear element rating is significantly reduced compared to conventional, solid-rod type fuel. The preliminary ICAF bundle concept considered in this study contains 24 half-metre long internally cooled annular fuel elements and one non-fuelled centre pin. The introduction of the non-fuelled centre pin reduces the coolant void reactivity (CVR), which is the increase in reactivity that occurs on voiding the coolant in accident scenarios. Lattice cell and full core physics calculations of the preliminary ICAF fuel bundle concept have been performed for medium burnups of approximately 18 GWd/tU using WIMS-AECL and reactor fuel simulation program (RFSP). The results will be used to assist in concept configuration optimization. The effects of radial and axial core power distributions, linear element power ratings, refuelling rates and operational power ramps have been analyzed. The results suggest that burnups of greater than 18 GWd/tU can be achieved in current reactor designs. At approximately 18 GWd/tU, expected maximum linear element ratings in a PT-HWR with online-refuelling are approximately 90 kW/m. These conditions would be prohibitive for solid-rod fuel, but may be possible in ICAF fuel given the reduced maximum fuel temperature as a function of linear element rating. (authors)

Operation and utilization of low power research reactor critical facility for Advanced Heavy Water Reactor (AHWR)

International Nuclear Information System (INIS)

De, S.K.; Karhadkar, C.G.

2017-01-01

An Advanced Heavy Water Reactor (AHWR) has been designed and developed for maximum power generation from thorium considering large reserves of thorium. The design envisages using 54 pin MOX cluster with different enrichment of "2"3"3U and Pu in Thoria fuel pins. Theoretical models developed to neutron transport and the geometrical details of the reactor including all reactivity devices involve approximations in modelling, resulting in uncertainties. With a view to minimize these uncertainties, a low power research reactor Critical Facility was built in which cold clean fuel can be arranged in a desired and precise geometry. Different experiments conducted in this facility greatly contribute to understand and validate the physics design parameters

Study of the light and heavy water leaks in nuclear reactors and development of techniques for their detection, location and estimation

International Nuclear Information System (INIS)

Bashiruddin Mahmood, S.

1979-01-01

In heavy water type nuclear reactors the detection and control of heavy water and light water escapes from different systems is of vital importance in the successful and economic operation of these type of plants. The high cost of heavy water makes it imperative to minimise all such escapes, in order to reduce the loss as well as the upgrading cost of downgraded collection recovered from the reactor building. Original methods and devices have been developed at the Karachi Nuclear Power Plant which successfully solve this problem. This report describes the constructional and operational features of these devices

Study relating to the physico-chemical behaviour of heavy water in nuclear reactors

International Nuclear Information System (INIS)

Chenouard, J.; Dirian, G.; Roth, E.; Vignet, P.; Platzer, R.

1959-01-01

Chemical and isotope pollution, and radiolytic decomposition are the two most important ways in which heavy water becomes degraded in nuclear reactors. Chemical pollution has led to the creation of ion exchange purification loops specially designed for reactors: the report contains a description in detail of the application of this purification method in CEA research reactors, including the analysis required, results obtained, and their interpretation. The intelligence obtained on radiolytic decomposition with the same facilities is also discussed, as well as the recombination apparatus and control equipment utilized. Finally, investigation to date in the CEA on recombination circuits for power reactors is also discussed. (author) [fr

Decontamination and recycle of zirconium pressure tubes from Pressurized Heavy Water Reactor

International Nuclear Information System (INIS)

Gantayet, L.M.; Verma, R.; Remya Devi, P.S.; Banerjee, S.; Kotak, V.; Raha, A.; Sandeep, K.C.; Joshi, Shreeram W.; Lali, A.M.

2009-01-01

An ion exchange process has been developed for decontamination of zirconium pressure tubes from Pressurized Heavy Water Reactor and recycling of neutronically improved zirconium. Distribution coefficient, equilibrium isotherm, kinetic and breakthrough data were used to develop the separation process. Effect of gamma radiation on indigenous resins was also studied to assess their suitability in high radiation field. (author)

Radiogenic lead with dominant content of {sup 208}Pb: New coolant and neutron moderator for innovative nuclear reactors

Energy Technology Data Exchange (ETDEWEB)

Shmelev, A. N.; Kulikov, G. G.; Kryuchkov, E. F.; Apse, V. A.; Kulikov, E. G. [National Research Nuclear Univ. MEPhI, Kashirskoe shosse, 31, 115409, Moscow (Russian Federation)

2012-07-01

The advantages of radiogenic lead with dominant content of {sup 208}Pb as a reactor coolant with respect to natural lead are caused by unique nuclear properties of {sup 208}Pb which is a double-magic nucleus with closed proton and neutron shells. This results in significantly lower micro cross section and resonance integral of radiative neutron capture by {sup 208}Pb than those for numerous light neutron moderators. The extremely weak ability of {sup 208}Pb to absorb neutrons results in the following effects. Firstly, neutron moderating factor (ratio of scattering to capture cross sections) is larger than that for graphite and light water. Secondly, age and diffusion length of thermal neutrons are larger than those for graphite, light and heavy water. Thirdly, neutron lifetime in {sup 208}Pb is comparable with that for graphite, beryllium and heavy water what could be important for safe reactor operation. The paper presents some results obtained in neutronics and thermal-hydraulics evaluations of the benefits from the use of radiogenic lead with dominant content of {sup 208}Pb instead of natural lead as a coolant of fast breeder reactors. The paper demonstrates that substitution of radiogenic lead for natural lead can offer the following benefits for operation of fast breeder reactors. Firstly, improvement of the reactor safety thanks to the better values of coolant temperature reactivity coefficient and, secondly, improvement of some thermal-hydraulic reactor parameters. Radiogenic lead can be extracted from thorium sludge without isotope separation as {sup 208}Pb is a final isotope in the decay chain of {sup 232}Th. (authors)

Comparison of methods for the determination of boron in heavy water moderator

International Nuclear Information System (INIS)

Green, L.W.; Davey, E.C.; Gulens, J.; Longhurst, T.H.; Mislan, J.P.

1984-01-01

Five analysis methods were compared for the determination of boron in heavy water moderator: isotope dilution mass spectrometry, spectrophotometry, neutron activation, inductively coupled plasma -atomic emission spectrometry, and ion selective electrode potentiometry. Ten samples were analysed by each method; the results showed close agreement between all of the methods. Only mass spectrometry achieved the required precision ( 10 B concentration must be determined, only mass spectrometry and neutron activation are applicable

Summary report of the 7th reduced-moderation water reactor workshop

International Nuclear Information System (INIS)

Akie, Hiroshi; Nabeshima, Kunihiko; Uchikawa, Sadao

2005-08-01

As a research on the future innovative water reactor, the development of Reduced-Moderation Water Reactors (RMWRs) has been performed in Japan Atomic Energy Research Institute (JAERI). The workshop on RMWRs is aiming at information exchange between JAERI and other organizations such as universities, laboratories, utilities and vendors, and has been held every year since 1998. The 7th workshop was held on March 5, 2004 under the joint auspices of JAERI and North Kanto branch of Atomic Energy Society of Japan. The program of the workshop was composed of 5 lectures and an overall discussion time. The workshop started with the lecture by JAERI on the status and future program of PMWR research and development, followed by the two presentations by JAERI and Japan Nuclear Cycle Development Institute, respectively, on the investigation and evaluation of water cooled reactor in Feasibility Study Program on Commercialized Fast Reactor Systems. The lectures were also made on the Japan's nuclear fuel cycle and scenarios for RMWRs deployment by JAERI, and on the next generation reactor development activity by Hitachi, Ltd. The main subjects of the overall discussion time were Na cooled fast reactor, deployment effects of RMWRs and the future plan of the RMWR research and development. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture, as well as of the discussion time. In addition in the Appendices, there are included presentation handouts of each lecture, program of the workshop and the participants list. (author)

Experimental determination of lattice parameters for 2% enriched uranium heavy water reactor cores

Energy Technology Data Exchange (ETDEWEB)

Raisic, N; Takac, S; Markovic, H; Bosevski, T [Boris Kidric Institute of Nuclear Sciences Vinca, Belgrade (Yugoslavia)

1963-04-15

Systematic measurements of the buckling, infinite multiplication factor and the thermal utilization factor were made on a series of lattices for 2% enriched uranium tubular fuel elements in heavy water. This work represents the first phase of experimental verification of standard theoretical methods used for the determination of reactor parameters.

Problems connected with the production of heavy water in France; Problemes relatifs a la production d'eau lourde en France

Energy Technology Data Exchange (ETDEWEB)

Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1956-07-01

The decision to study the nuclear energy in France in 1945 has seen the construction of the first natural uranium reactor for research purpose only, Zoe reactor. The utilization of heavy water as moderator was motivated by permitting the economical utilization of natural uranium oxides as fuel and a good handling. The five tons of heavy water required by the Zoe reactor were initially obtained from Norway production. With nuclear development and the construction of the first power reactors for electricity production, the demand in heavy water increased. The heavy water production by French industry became of a great interest. The first production started in the southwest of France using a fertilizers production plant and the electrolytic process used in Norway. The electrolytic process of hydrogen was quickly limited by the limited number of large fertilizers plants in France. Thus, in 1953, French nuclear research concentrated on the distillation of liquid hydrogen and water distillation for the heavy water production. The liquid hydrogen distillation presents a better yield in heavy water extraction than the electrolytic process but it was still depending from large fertilizers production plants. Although the water distillation process is simple, the high purity required for nuclear uses induced a high cost. The advantages and disadvantages of these two processes are discussed as well as others heavy water production processes using concentration process of already enriched water and the prospect of the use of the natural gas from the Lacq deposit. Economical aspect and cost production for each of heavy water production processes will be also discussed. (M.P.)

The advanced MAPLE reactor concept

International Nuclear Information System (INIS)

Lidstone, R.F.; Lee, A.G.; Gillespie, G.E.; Smith, H.J.

1989-01-01

In Canada the need for advanced neutron sources has long been recognized. During the past several years Atomic Energy of Canada Limited (AECL) has been developing the new MAPLE multipurpose reactor concept. To date, the MAPLE program has focused on the development of a modest-cost multipurpose medium-flux neutron source to meet contemporary requirements for applied and basic research using neutron beams, for small-scale materials testing and analysis and for radioisotope production. The basic MAPLE concept incorporates a compact light-water cooled and moderated core within a heavy water primary reflector to generate strong neutron flux levels in a variety of irradiation facilities. In view of renewed Canadian interest in a high-flux neutron source, the MAPLE group has begun to explore advanced concepts based on AECL's experience with heavy water reactors. The overall objective is to define a high-flux facility that will support materials testing for advanced power reactors, new developments in extracted neutron-beam applications, and/or production of radioisotopes. The design target is to attain performance levels of HFR-Grenoble, HFBR, HFIR in a new heavy water-cooled, -moderated,-reflected reactor based on rodded LEU fuel. Physics, shielding, and thermohydraulic studies have been performed for the MAPLE heavy water reactor. 14 refs., 4 figs., 1 tab

Development of a standard for calculation and measurement of the moderator temperature coefficient of reactivity in water-moderated power reactors

International Nuclear Information System (INIS)

Mosteller, R.D.; Hall, R.A.; Lancaster, D.B.; Young, E.H.; Gavin, P.H.; Robertson, S.T.

1998-01-01

The contents of ANS 19.11, the standard for ''Calculation and Measurement of the Moderator Temperature Coefficient of Reactivity in Water-Moderated Power Reactors,'' are described. The standard addresses the calculation of the moderator temperature coefficient (MTC) both at standby conditions and at power. In addition, it describes several methods for the measurement of the at-power MTC and assesses their relative advantages and disadvantages. Finally, it specifies a minimum set of documentation requirements for compliance with the standard

Assessment of the accident response of a light-water-moderated breeder-reactor system: AWBA development program

International Nuclear Information System (INIS)

High, H.M.

1983-05-01

The predicted accident response for a light water moderated, thorium/U-233 fueled, seed-blanket reactor concept was assessed. The first part of the assessment compared breeder accident response with that of a current commercial pressurized water reactor design for several different types of transients. Based on these comparisons and a review of the various parameter differences between the breeder and a U-235 fueled plant, the second part of the assessment studied the breeder accident behavior in more detail, particularly in areas of potential concern. Based on the two parts of the assessment, it was concluded that the breeder accident response would be very similar to that of present commercial pressurized water reactor plants. The large Doppler and moderator reactivity coefficients of the breeder would significantly reduce the severity of many of the accidents that must be considered. It is expected that the accident response of the breeder can be shown to meet regulatory criteria

Reactor core simulations in Canada

International Nuclear Information System (INIS)

Roy, R.; Koclas, J.; Shen, W.; Jenkins, D. A.; Altiparmakov, D.; Rouben, B.

2004-01-01

This review will address the current simulation flow-chart currently used for reactor-physics simulations in the Canadian industry. The neutron behaviour in heavy-water moderated power reactors is quite different from that in other power reactors, thus the core physics approximations are somewhat different Some codes used are particular to the context of heavy-water reactors, and the paper focuses on this aspect. The paper also shows simulations involving new design features of the Advanced Candu Reactor TM (ACR TM), and provides insight into future development, expected in the coming years. (authors)

Moderator purification and design modifications based on operation feedback

International Nuclear Information System (INIS)

Das, S.; Chakrabarti, A.K.; Shirolkar, K.M.; Sharma, V.K.

1994-01-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author)

Reactor core

International Nuclear Information System (INIS)

Azekura, Kazuo; Kurihara, Kunitoshi.

1992-01-01

In a BWR type reactor, a great number of pipes (spectral shift pipes) are disposed in the reactor core. Moderators having a small moderating cross section (heavy water) are circulated in the spectral shift pipes to suppress the excess reactivity while increasing the conversion ratio at an initial stage of the operation cycle. After the intermediate stage of the operation cycle in which the reactor core reactivity is lowered, reactivity is increased by circulating moderators having a great moderating cross section (light water) to extend the taken up burnup degree. Further, neutron absorbers such as boron are mixed to the moderator in the spectral shift pipe to control the concentration thereof. With such a constitution, control rods and driving mechanisms are no more necessary, to simplify the structure of the reactor core. This can increase the fuel conversion ratio and control great excess reactivity. Accordingly, a nuclear reactor core of high conversion and high burnup degree can be attained. (I.N.)

Study of the heavy water regeneration processes; Studija procesa za regeneraciju teske vode

Energy Technology Data Exchange (ETDEWEB)

Cavcic, E [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

1965-11-15

Experience derived from heavy water reactor operation showed degradation and dilution of heavy water to be inevitable depends on the type of reactor. Dilution of heavy water during operation of the RA and the RB reactors is shown in this report. Principles and procedures of heavy water regeneration by electrolysis, fractional distillation, cleaning, prevention of tritium contamination are described as well as separation columns.

Moderator feedback effects in two-dimensional nodal methods for pressurized water reactor analysis

International Nuclear Information System (INIS)

Downar, T.J.

1987-01-01

A method was developed for incorporating moderator feedback effects in two-dimensional nodal codes used for pressurized water reactor (PWR) neutronic analysis. Equations for the assembly average quality and density are developed in terms of the assembly power calculated in two dimensions. The method is validated with a Westinghouse PWR using the Electric Power Research Institute code SIMULATE-E. Results show a several percent improvement is achieved in the two-dimensional power distribution prediction compared to methods without moderator feedback

Preliminary Assessment of Heavy-Water Thorium Reactors in the Brazilian Nuclear Programme

Energy Technology Data Exchange (ETDEWEB)

Salvo Brito, S. de; Lepecki, W. P.S. [Instituto de Pesquisas Radioativas, Belo Horizonte (Brazil)

1968-04-15

Since December 1965, the Instituto de Pesquisas Radioativas has been studying for the Brazilian Nuclear Energy Commission the feasibility of a thorium reactor programme in Brazil; since June 1966, the programme has been developed in close co-operation with the French Atomic Energy Commission. A reference conceptual design of a heavy-water-cooled and -moderated thorium converter reactor has been developed. The main features of that concept are the use of a prestressed-concrete pressure vessel, integrated arrangement of the primary circuit and the possibility of on-load fuel management. Economic competitiveness could be the result of high compactness, low capital costs and low fuel consumption. The technology involved is not very sophisticated; intensive engineering development work must be done in areas like fuel charge machine, concrete vessel insulation, and proper design of heat exchangers, but it is the feeling of the Group that these problems could be solved without seriously compromising the economic feasibility of the concept. Preliminary studies were made on the alternative use of enriched uranium or plutonium as a feed for the programme; in the latter case, plutonium could be produced in natural uranium reactors of the same type. The general conditions favouring each of these approaches to the thorium cycle have been determined, in particular those related to the costs of the fissile materials in the world market and to the country's policy related to nuclear fuel imports. The results of the preliminary studies are very encouraging and could justify the beginning of a research and development programme leading to the construction of a prototype in the 1970's. (author)

Improvements in gas supply systems for heavy-water moderated reactors; Etudes de perfectionnements aux systemes d'alimentation en gaz d'un reacteur modere a l'eau lourde

Energy Technology Data Exchange (ETDEWEB)

Aubert, G; Hassig, J M; Laurent, N; Thomas, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

In a heavy-water moderated reactor cooled by pressurized gas, an important problem from the point of view, of the reactor block and its economics is the choice of the gas supply system. In the pressure tube solution, the whole of the reactor block structure is at a relatively low temperature, whereas the gas supply equipment is at that of the gas, which is much higher. These parts, through which passes the heat carrying fluid have to present as low a resistance as possible to it so as to avoid costly extra blowing power. Finally, they may only be placed in the reactor block after it has been built; the time required for putting them in position should therefore not be too long. The work reported here concerns the various problems arising in the case of each channel being supplied individually by a tube at the entry and the exit which is connected to a main circuit made up of large size collectors. This individual tubing is sufficiently flexible to absorb the differential expansion and the movement of its ends without stresses or prohibitive reactions being produced; the tubing is also of relatively short length so as to reduce the pressure head of the pressurized gas outside the channels; the small amount of space taken up by the tubing makes it possible to assemble it in a manner which is satisfactory from the point of view both of the time required and of the technical quality. (authors) [French] Dans un reacteur modere a l'eau lourde et refroidi au gaz sous pression, un probleme important du point de vue du trace du bloc pile et de son economie est le choix du systeme d'alimentation en gaz. Pour une solution a tubes de force, l'ensemble des structures du bloc reacteur est a temperature relativement faible, alors que les organes d'alimentation en gaz sont a celle, notablement plus elevee, du gaz. Ces organes, traverses par le debit du caloporteur, doivent lui opposer le minimum de resistance afin de ne pas necessiter un supplement onereux de puissance de

Thermal gradients caused by the CANDU moderator circulation

International Nuclear Information System (INIS)

Mohindra, V.K.; Vartolomei, M.A.; Scharfenberg, R.

2008-01-01

The heavy water moderator circulation system of a CANDU reactor, maintains calandria moderator temperature at power-dependent design values. The temperature differentials between the moderator and the cooler heavy water entering the calandria generate thermal gradients in the reflector and moderator. The resultant small changes in thermal neutron population are detected by the out-of-core ion chambers as small, continuous fluctuations of the Log Rate signals. The impact of the thermal gradients on the frequency of the High Log Rate fluctuations and their amplitude is relatively more pronounced for Bruce A as compared to Bruce B reactors. The root cause of the Log Rate fluctuations was investigated using Bruce Power operating plant information data and the results of the investigation support the interpretation based on the thermal gradient phenomenon. (author)

Moderator purification and design modifications based on operation feedback

Energy Technology Data Exchange (ETDEWEB)

Das, S; Chakrabarti, A K; Shirolkar, K M; Sharma, V K [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author). 2 refs., 3 figs., 1 tab.

A plan of reactor physics experiments for reduced-moderation water reactors with MOX fuel in TCA

International Nuclear Information System (INIS)

Shimada, Shoichiro; Akie, Hiroshi; Suzaki, Takenori; Okubo, Tutomu; Usui, Shuji; Shirakawa, Toshihisa; Iwamura, Takamiti; Kugo, Teruhiko; Ishikawa, Nobuyuki

2000-06-01

The Reduced-Moderation Water Reactor (RMWR) is one of the next generation water-cooled reactors which aim at effective utilization of uranium resource, high burn-up, long operation cycle, and plutonium multi-recycle. For verification of the feasibility, negative void reactivity coefficient and conversion ratio more than 1.0 must be confirmed. Critical Experiments performed so far in Eualope and Japan were reviewed, and no useful data are available for RMWR development. Critical experiments using TCA (Tank Type Critical Assembly) in JAERI are planned. MOX fuel rods should be prepared for the experiments and some modifications of the equipment are needed for use of MOX fuel rods. This report describes the preliminary plan of physics experiments. The number of MOX fuel rods used in the experiments are obtained by calculations and the modification of the equipment for the experiments are shown. (author)

The status of improved pressurized heavy water reactor development - A new option for PHWR -

International Nuclear Information System (INIS)

Park, Tae Keun; Yeo, Ji Won

1996-03-01

Currently, the 900 MWe class Improved Pressurized Heavy Water Reactor (PHWR), which is a type of CANDU reactor based on the systems and components of operating CANDU plants, is under development. The improved PHWR has a 480 fuel channel calandria, uses 37 element natural uranium fuel bundles and has a single unit containment. Adaptation of a steel-lined containment structure and improved containment isolation systems permit a reduced exclusion area boundary (EAB) compared to the existing larger capacity CANDU reactors (Darlington, Bruce B). The improved PHWR buildings are arranged to achieve minimum spacing between reactor units. Plant safety and economy are increased through various design changes based on the operating experience of existing CANDU plants. 4 refs. (Author)

Study on the effect of moderator density reactivity for Kartini reactor

International Nuclear Information System (INIS)

Budi Rohman; Widarto

2009-01-01

One of important characteristics of water-cooled reactors is the change of reactivity due to change in the density of coolant or moderator. This parameter generally has negative value and it has significant role in preventing the excursion of power during operation. Many thermal-hydraulic codes for nuclear reactors require this parameter as the input to account for reactivity feedback due to increase in moderator voids and the subsequent decrease in moderator density during operation. Kartini reactor is cooled and moderated by water, therefore, it is essential to study the effect of the change in moderator density as well as to determine the value of void or moderator density reactivity coefficient in order to characterize its behavior resulting from the presence of vapor or change of moderator density during operation. Analysis by MCNP code shows that the reactivity of core is decreasing with the decrease in moderator density. The analysis estimates the void or moderator density reactivity coefficient for Kartini Reactor to be -2.17×10-4 Δρ/ % void . (author)

Noise analysis method for monitoring the moderator temperature coefficient of pressurized water reactors: Neural network calibration

International Nuclear Information System (INIS)

Thomas, J.R. Jr.; Adams, J.T.

1994-01-01

A neural network was trained with data for the frequency response function between in-core neutron noise and core-exit thermocouple noise in a pressurized water reactor, with the moderator temperature coefficient (MTC) as target. The trained network was subsequently used to predict the MTC at other points in the same fuel cycle. Results support use of the method for operating pressurized water reactors provided noise data can be accumulated for several fuel cycles to provide a training base

Control of xenon oscillations in Advanced Heavy Water Reactor via two-stage decomposition

International Nuclear Information System (INIS)

Munje, R.K.; Parkhe, J.G.; Patre, B.M.

2015-01-01

Highlights: • Singularly perturbed model of Advanced Heavy Water Reactor is explored. • Composite controller is designed using slow subsystem alone, which achieves asymptotic stability. • Nonlinear simulations are carried out under different transient conditions. • Performance of the controller is found to be satisfactory. - Abstract: Xenon induced spatial oscillations developed in large nuclear reactors, like Advanced Heavy Water Reactor (AHWR) need to be controlled for safe operation. Otherwise, a serious situation may arise in which different regions of the core may undergo variations in neutron flux in opposite phase. If these oscillations are left uncontrolled, the power density and rate of change of power at some locations in the reactor core may exceed their respective thermal limits, resulting in fuel failure. In this paper, a state feedback based control strategy is investigated for spatial control of AHWR. The nonlinear model of AHWR including xenon and iodine dynamics is characterized by 90 states, 5 inputs and 18 outputs. The linear model of AHWR, obtained by linearizing the nonlinear equations is found to be highly ill-conditioned. This higher order model of AHWR is first decomposed into two comparatively lower order subsystems, namely, 73rd order ‘slow’ subsystem and 17th order ‘fast’ subsystem using two-stage decomposition. Composite control law is then derived from individual subsystem feedback controls and applied to the vectorized nonlinear model of AHWR. Through the dynamic simulations it is observed that the controller is able to suppress xenon induced spatial oscillations developed in AHWR and the overall performance is found to be satisfactory

Verification of HELIOS-MASTER system through benchmark of Halden boiling water reactor (HBWR)

International Nuclear Information System (INIS)

Kim, Ha Yong; Song, Jae Seung; Cho, Jin Young; Kim, Kang Seok; Lee, Chung Chan; Zee, Sung Quun

2004-01-01

To verify the HELIOS-MASTER computer code system for a nuclear design, we have been performed benchmark calculations for various reactor cores. The Halden reactor is a boiling, heavy water moderated reactor. At a full power of 18-20MWt, the moderator temperature is 240 .deg. C and the pressure is 33 bar. This study describes the verification of the HELIOS-MASTER computer code system for a nuclear design and the analysis of a hexagonal and D 2 O moderated core through a benchmark of the Halden reactor core. HELIOS, developed by Scandpower A/S, is a two-dimensional transport program for the generation of group cross-sections, and MASTER, developed by KAERI, is a three-dimensional nuclear design and analysis code based on the two-group diffusion theory. It solves the neutronics model with the TPEN (Triangle based Polynomial Expansion Nodal) method for a hexagonal geometry

The Bare Critical Assembly of Natural Uranium and Heavy Water

Energy Technology Data Exchange (ETDEWEB)

Popovic, D [Boris Kidric Institute of Nuclear Sciences, Vinca, Belgrade (Yugoslavia)

1958-07-01

The first reactor built in Yugoslavia was the bare zero energy heavy water and natural uranium assembly at the Boris Kidric Institute of Nuclear Sciences, Belgrade. The reactor went critical on April 29, 1958. The possession of four tons of natural uranium metal and the temporary availability of seven tons of heavy water encouraged the staff of the Institute to build a critical assembly. A critical assembly was chosen, rather than high flux reactor, because the heavy water was available only temporarily. Besides, a 10 MW, enriched uranium, research reactor is being built at the same Institute and should be ready for operation late this year. It was supposed that the zero energy reactor would provide experience in carrying out critical experiments, operational experience with nuclear reactors, and the possibility for an extensive program in reactor physics. (author)

Heavy water at Trail, British Columbia

International Nuclear Information System (INIS)

Arsenault, J.E.

2006-01-01

Today Canada stands on the threshold of a nuclear renaissance, based on the CANDU reactor family, which depends on heavy water as a moderator and for cooling. Canada has a long history with heavy water, with commercial interests beginning in 1934, a mere two years after its discovery. At one time Canada was the world's largest producer of heavy water. The Second World War stimulated interest in this rather rare substance, such that the worlds largest supply (185 kg) ended up in Canada in 1942 to support nuclear research work at the Montreal Laboratories of the National Research Council. A year later commercial production began at Trail, British Columbia, to support work that later became known as the P-9 project, associated with the Manhattan Project. The Trail plant produced heavy water from 1943 until 1956, when it was shut down. During the war years the project was so secret that Lesslie Thomson, Special Liaison Officer reporting on nuclear matters to C.D. Howe, Minister of Munitions and Supply, was discouraged from visiting Trail operations. Thomson never did visit the Trail facility during the war. In 2005 the remaining large, tall concrete exchange tower was demolished at a cost of about $2.4 million, about the same as it cost to construct the facility about 60 years ago. Thus no physical evidence remains of this historic facility and another important artifact from Canada's nuclear history has disappeared forever. It is planned to place a plaque at the site at some point in the future. (author)

Heavy water at Trail, British Columbia

Energy Technology Data Exchange (ETDEWEB)

Arsenault, J.E. [Ontario (Canada)

2006-09-15

Today Canada stands on the threshold of a nuclear renaissance, based on the CANDU reactor family, which depends on heavy water as a moderator and for cooling. Canada has a long history with heavy water, with commercial interests beginning in 1934, a mere two years after its discovery. At one time Canada was the world's largest producer of heavy water. The Second World War stimulated interest in this rather rare substance, such that the worlds largest supply (185 kg) ended up in Canada in 1942 to support nuclear research work at the Montreal Laboratories of the National Research Council. A year later commercial production began at Trail, British Columbia, to support work that later became known as the P-9 project, associated with the Manhattan Project. The Trail plant produced heavy water from 1943 until 1956, when it was shut down. During the war years the project was so secret that Lesslie Thomson, Special Liaison Officer reporting on nuclear matters to C.D. Howe, Minister of Munitions and Supply, was discouraged from visiting Trail operations. Thomson never did visit the Trail facility during the war. In 2005 the remaining large, tall concrete exchange tower was demolished at a cost of about $2.4 million, about the same as it cost to construct the facility about 60 years ago. Thus no physical evidence remains of this historic facility and another important artifact from Canada's nuclear history has disappeared forever. It is planned to place a plaque at the site at some point in the future. (author)

Advanced light-water reactors

International Nuclear Information System (INIS)

Golay, M.W.; Todreas, N.E.

1990-01-01

Environmental concerns, economics and the earth's finite store of fossil fuels argue for a resuscitation of nuclear power. The authors think improved light-water reactors incorporating passive safety features can be both safe and profitable, but only if attention is paid to economics, effective management and rigorous training methods. The experience of nearly four decades has winnowed out designs for four basic types of reactor: the heavy-water reactor (HWR), the gas-cooled rector (GCR), the liquid-metal-cooled reactor (LMR) and the light-water reactor (LWR). Each design is briefly described before the paper discusses the passive safety features of the AP-600 rector, so-called because it employs an advanced pressurized water design and generates 600 MW of power

Thermal hydraulic simulation of moderator heat exchanger

International Nuclear Information System (INIS)

Anil Lal, S.; Rajakumar, A.; Vaidyanathan, G.; Srinivasan, R.; Chetal, S.C.

1993-01-01

Pressurized heavy water reactors form the majority in the first stage of India's nuclear power programme. Heavy water is both moderator and primary coolant. The heat generated in the moderator due to neutron moderation and capture has to be removed in moderator heat exchangers. It has been desired to improve the performance characteristics of moderator heat exchangers, whereby moderator would enter the calandria vessel at a low temperature and would enable higher power of operation for the same limiting temperature of moderator in the calandria. Results of studies carried out using a three dimensional computer code for various operating options are given. Using these velocities the heat exchangers have been analysed for flow induced vibrations. 7 refs., 6 figs., 6 tabs

Quality assurance in the manufacture of metallic uranium fuel for research reactors

International Nuclear Information System (INIS)

Shah, B.K.; Kumar, Arbind; Nanekar, P.P.; Vaidya, P.R.

2009-01-01

Two Research Reactors viz. CIRUS and DHRUVA are operating at Trombay since 1960 and 1985 respectively. Cirus is a 40 MWth reactor using heavy water as moderator and light water as coolant. Dhruva is a 100 MWth reactor using heavy water as moderator and coolant. The maximum neutron flux of these reactors are 6.7 x 10 13 n/cm 2 /s (Cirus) and 1.8 x 10 14 n/cm 2 /s (Dhruva). Both these reactors are used for basic research, R and D in reactor technology, isotope production and operator training. Fuel material for these reactors is natural uranium metallic rods claded in finned aluminium (99.5%) tubes. This presentation will discuss various issues related to fabrication quality assurance and reactor behavior of metallic uranium fuel used in research reactors

Reactors of different types in the world nuclear power

International Nuclear Information System (INIS)

Simonov, K.V.

1991-01-01

The status of the world nuclear power is briefly reviewed. It is noted that PWR reactors have decisive significance in the world power. The second place is related to gas-cooled graphite-moderated reactors. Channel-type heavy water moderated reactors are relatively important. Nuclear power future is associated with fast liquid-metal cooled breeder reactors

Chemical elimination of alumina in suspension in nuclear reactors heavy water; Elimination de l'alumine en suspension dans l'eau lourde des reacteurs nucleaires par voie chimique

Energy Technology Data Exchange (ETDEWEB)

Ledoux, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1967-02-01

Corrosion of aluminium in contact with moderating water in nuclear reactor leads to the formation of an alumina hydrosol which can have an adverse effect on the operation of the reactor. Several physical methods have been used in an attempt to counteract this effect. The method proposed here consists in the elimination of the aluminium by dissolution and subsequent fixation in the ionic form on mixed-bed ion-exchange resin. In order to do this, the parameters and the values of these parameters most favorable to the dissolution process have been determined. If the moderator is heavy water, the deuterated acid can be prepared by converting a solution in heavy water to a salt of the acid using a deuterated cationic resin. (author) [French] La corrosion de l'aluminium au contact de l'eau moderatrice des reacteurs nucleaires, donne lieu a la formation d'un hydrosol d'alumine nuisible au bon fonctionnement des reacteurs. Plusieurs methodes physiques ont ete mises en oeuvre pour pallier ces inconvenients. On propose ici d'eliminer l'alumine par solubilisation pour la fixer ensuite sous forme ionique par des resines echangeuses d'ions, en lit melange. A cette fin on determine les parametres et leurs grandeurs favorables a cette solubilisation. Si le moderateur est de l'eau lourde la preparation d'acide deutere peut etre effectuee par passage d'une solution en eau lourde a un sel de l'acide sur resine cationique deuteree.

Study of new structures adapted to gas-graphite and gas-heavy water reactors

International Nuclear Information System (INIS)

Martin, R.; Roche, R.

1964-01-01

The experience acquired as a result of the operation of the Marcoule reactors and of the construction and start-up of the E.D.F. reactors on the one hand, and the conclusions of research and tests carried out out-of-pile on the other hand, lead to a considerable change in the general design of reactors of the gas-graphite type. The main modifications envisaged are analysed in the paper. The adoption of an annular fuel element and of a down-current cooling will make it possible to increase considerably the specific power and the power output of each channel; as a result there will be a considerable reduction in the number of the channels and a corresponding increase in the size of the unit cell. The graphite stack will have to be adapted to there new conditions. For security reasons, the use of prestressed concrete for the construction of the reactor vessel is becoming more widespread; they could lead to the exchangers and the fuel-handling apparatus becoming integrated inside the vessel (the so-called 'attic' device). A full-size mode) of this attic has been built at Saclay with the participation of EURATOM; the operational results obtained are presented as well as a new original design for the control rods. As for as the gas-heavy-water system is concerned, the research is carried out on two points of design; the first, which retains the use of horizontal pressure tubes, takes into account the experience acquired during the construction of the EL 4 reactor of which it will constitute an extrapolation; the second, arising from the research carried out on the gas-graphite system, will use a pre-stressed concrete vessel for holding the pressure, the moderator being almost at the same pressure as the cooling fluid and the fuel being placed in vertical channels. The relative merits of these two variants are analysed in the present paper. (authors) [fr

Development of a purification system at Dhruva to treat oil contaminated and chemically impure heavy water

International Nuclear Information System (INIS)

Suttraway, S.K.; Mishra, V.; Bitla, S.V.; Ghosh, S.K.

2006-01-01

Dhruva, a 100 MW (thermal) Research reactor uses Heavy Water as moderator, reflector and coolant. Normally during plant operation, the Heavy water from the system gets removed during operational and maintenance activities and this collected heavy water gets degraded and contaminated in the process. The degraded heavy water meeting the chemical specification requirement of the up gradation plant is sent for up gradation. Part of the Heavy water collected is contaminated with various organic and inorganic impurities and therefore cannot be sent for IP up gradation as it does not meet the chemical specification of the up gradation plant. This contaminated Heavy water was being stored in SS drums. Over the years of Reactor operation reasonable amount of contaminated Heavy water got collected in the plant. This Heavy water collected from leakages, during routine maintenance, operational activities and fuelling operation had tritium activity and variety of contamination including oil, chlorides, turbidity due to which the specific conductivity was very high. It was decided to purify this Heavy water in house to bring it up to up gradation plant chemical specification requirement. There were number of challenges in formulating a scheme to purify this Heavy water. The scheme needed to be simple and compact in design which could be set up in the plant itself. It should not pose radiological hazards due to radioactive Heavy water during its purification and handling. The contaminated Heavy water collected in drums had varying chemistry and IP. The purification plant should be able to do batch processing so that the different IP and chemical quality of Heavy water stored in different drums are not mixed during purification. It should be capable of removing the oil, chlorides, turbidity and decrease the conductivity to acceptable limits of the Up gradation plant. A purification plant was developed and commissioned after detail laboratory studies and trials. This paper explains

Heavy water lattices: Second panel report

International Nuclear Information System (INIS)

1963-01-01

The panel was attended by prominent physicists from most of the laboratories engaged in the field of heavy water lattices throughout the world. The participants presented written contributions and status reports describing the past history and plans for further development of heavy-water reactors. Valuable discussions took place, during which recommendations for future work were formulated. Refs, figs, tabs

Heavy water lattices: Second panel report

Energy Technology Data Exchange (ETDEWEB)

1963-09-15

The panel was attended by prominent physicists from most of the laboratories engaged in the field of heavy water lattices throughout the world. The participants presented written contributions and status reports describing the past history and plans for further development of heavy-water reactors. Valuable discussions took place, during which recommendations for future work were formulated. Refs, figs, tabs.

Status and perspective of development of cold moderators at the IBR-2 reactor

International Nuclear Information System (INIS)

Kulikov, S; Shabalin, E

2012-01-01

The modernized IBR-2M reactor will start its operation with three water grooved moderators in 2011. Afterwards, they will be exchanged by a new complex of moderators. The complex consists of three so-called kombi-moderators, each of them containing a pre-moderator, a cold moderator, grooved ambient water moderators and post-moderators. They are mounted onto three moveable trolleys that serve to deliver and install moderators near the reactor core. The project is divided in three stages. In 2012 the first stage of development of complex of moderators will be finished. The water grooved moderator will be replaced with the new kombi-moderator for beams nos. 7, 8, 10, 11. Main parameters of moderators for this direction will be studied then. The next stages will be done for beams nos. 2-3 and for beams nos. 1, 9, 4-6, consequently. Cold moderator chambers at the modernized IBR-2 reactor are filled with thousands of beads (∼3.5 - 4 mm in diameter) of moderating material. The cold helium gas flow delivers beads from the charging device to the moderator during the fulfillment process and cools down them during the reactor cycle. The mixture of aromatic hydrocarbons (mesithylen and m-xylen) has been chosen as moderating material. The explanation of the choice of material for novel cold neutron moderators, configuration of moderator complex for the modernized IBR-2 reactor and the main results of optimization of moderator complex for the third stage of moderator development are discussed in the article.

Status and perspective of development of cold moderators at the IBR-2 reactor

Science.gov (United States)

Kulikov, S.; Shabalin, E.

2012-03-01

The modernized IBR-2M reactor will start its operation with three water grooved moderators in 2011. Afterwards, they will be exchanged by a new complex of moderators. The complex consists of three so-called kombi-moderators, each of them containing a pre-moderator, a cold moderator, grooved ambient water moderators and post-moderators. They are mounted onto three moveable trolleys that serve to deliver and install moderators near the reactor core. The project is divided in three stages. In 2012 the first stage of development of complex of moderators will be finished. The water grooved moderator will be replaced with the new kombi-moderator for beams #7, 8, 10, 11. Main parameters of moderators for this direction will be studied then. The next stages will be done for beams #2-3 and for beams #1, 9, 4-6, consequently. Cold moderator chambers at the modernized IBR-2 reactor are filled with thousands of beads (~3.5 - 4 mm in diameter) of moderating material. The cold helium gas flow delivers beads from the charging device to the moderator during the fulfillment process and cools down them during the reactor cycle. The mixture of aromatic hydrocarbons (mesithylen and m-xylen) has been chosen as moderating material. The explanation of the choice of material for novel cold neutron moderators, configuration of moderator complex for the modernized IBR-2 reactor and the main results of optimization of moderator complex for the third stage of moderator development are discussed in the article.

Future development in heavy water reactors in Canada

International Nuclear Information System (INIS)

Donnelly, J.; Hart, R.G.

1982-01-01

1982 marks the 35th anniversary of the start-up of Canada's first research and test reactor, NRX. Its first power reactor has been operating successfully for the past 20 years. With 5,000 MWe of domestic capacity installed, Canada's major CANDU (Canada Deuterium, Uranium) nuclear program has a further 9,500 MWe under construction in Canada for completion by 1990 as well as committed offshore projects in Argentina, Korea and Romania. The CANDU operating record, by any measure of performance, has been outstanding. This performance is largely due to the discipline imposed on the development, design, construction and operation by two fundamental choices: natural uranium and heavy water. The impact of these two choices on availability, fuel utilization, safety and economics is discussed. Future plans call for building on those characteristics which have made CANDU so successful. When time for change comes, current assessments indicate that it will be possible to convert to more efficient advanced fuel cycles without major changes to the basic CANDU design. Primary attention is being focussed on thorium fuel cycles to ensure an abundant and continuing supply of low cost energy for the long term. The resource savings available from these fuel cycles in expanding systems are reviewed and compared with those available from LWR's and Fast Breeders. The results clearly illustrate the versatility of the CANDU reactor. It can benefit from enrichment plants or get along without them. It can complement LWR's or compete with them. It can complement Fast Breeder Reactors or compete with them as well. In the very long term CANDU's and Fast Breeders combined offer the potential of burning all the world's uranium and all the world's thorium. (author)

Further evaluations of the toxicity of irradiated advanced heavy water reactor fuels.

Science.gov (United States)

Edwards, Geoffrey W R; Priest, Nicholas D

2014-11-01

The neutron economy and online refueling capability of heavy water moderated reactors enable them to use many different fuel types, such as low enriched uranium, plutonium mixed with uranium, or plutonium and/or U mixed with thorium, in addition to their traditional natural uranium fuel. However, the toxicity and radiological protection methods for fuels other than natural uranium are not well established. A previous paper by the current authors compared the composition and toxicity of irradiated natural uranium to that of three potential advanced heavy water fuels not containing plutonium, and this work uses the same method to compare irradiated natural uranium to three other fuels that do contain plutonium in their initial composition. All three of the new fuels are assumed to incorporate plutonium isotopes characteristic of those that would be recovered from light water reactor fuel via reprocessing. The first fuel investigated is a homogeneous thorium-plutonium fuel designed for a once-through fuel cycle without reprocessing. The second fuel is a heterogeneous thorium-plutonium-U bundle, with graded enrichments of U in different parts of a single fuel assembly. This fuel is assumed to be part of a recycling scenario in which U from previously irradiated fuel is recovered. The third fuel is one in which plutonium and Am are mixed with natural uranium. Each of these fuels, because of the presence of plutonium in the initial composition, is determined to be considerably more radiotoxic than is standard natural uranium. Canadian nuclear safety regulations require that techniques be available for the measurement of 1 mSv of committed effective dose after exposure to irradiated fuel. For natural uranium fuel, the isotope Pu is a significant contributor to the committed effective dose after exposure, and thermal ionization mass spectrometry is sensitive enough that the amount of Pu excreted in urine is sufficient to estimate internal doses, from all isotopes, as low

Evaluation of fuel fabrication and the back end of the fuel cycle for light-water- and heavy-water-cooled nuclear power reactors

International Nuclear Information System (INIS)

Carter, W.L.; Olsen, A.R.

1979-06-01

The classification of water-cooled nuclear reactors offers a number of fuel cycles that present inherently low risk of weapons proliferation while making power available to the international community. Eight fuel cycles in light water reactor (LWR), heavy water reactor (HWR), and the spectral shift controlled reactor (SSCR) systems have been proposed to promote these objectives in the International Fuel Cycle Evaluation (INFCE) program. Each was examined in an effort to provide technical and economic data to INFCE on fuel fabrication, refabrication, and reprocessing for an initial comparison of alternate cycles. The fuel cycles include three once-through cycles that require only fresh fuel fabrication, shipping, and spent fuel storage; four cycles that utilize denatured uranium--thorium and require all recycle operations; and one cycle that considers the LWR--HWR tandem operation requiring refabrication but no reprocessing

Evaluation of fuel fabrication and the back end of the fuel cycle for light-water- and heavy-water-cooled nuclear power reactors

Energy Technology Data Exchange (ETDEWEB)

Carter, W.L.; Olsen, A.R.

1979-06-01

The classification of water-cooled nuclear reactors offers a number of fuel cycles that present inherently low risk of weapons proliferation while making power available to the international community. Eight fuel cycles in light water reactor (LWR), heavy water reactor (HWR), and the spectral shift controlled reactor (SSCR) systems have been proposed to promote these objectives in the International Fuel Cycle Evaluation (INFCE) program. Each was examined in an effort to provide technical and economic data to INFCE on fuel fabrication, refabrication, and reprocessing for an initial comparison of alternate cycles. The fuel cycles include three once-through cycles that require only fresh fuel fabrication, shipping, and spent fuel storage; four cycles that utilize denatured uranium--thorium and require all recycle operations; and one cycle that considers the LWR--HWR tandem operation requiring refabrication but no reprocessing.

Energetics of semi-catalyzed-deuterium, light-water-moderated, fusion-fission toroidal reactors

International Nuclear Information System (INIS)

Jassby, D.L.; Towner, H.H.; Greenspan, E.; Schneider, A.; Misolovin, A.; Gilai, D.

1978-07-01

The semi-catalyzed-deuterium Light-Water Hybrid Reactor (LWHR) comprises a lithium-free light-water-moderated blanket with U 3 Si fuel driven by a deuterium-based fusion-neutron source, with complete burn-up of the tritium but almost no burn-up of the helium-3 reaction product. A one-dimensional model for a neutral-beam-driven tokamak plasma is used to determine the operating modes under which the fusion energy multiplication Q/sub p/ can be equal to or greater than 0.5. Thermonuclear, beam-target, and energetic-ion reactions are taken into account. The most feasible operating conditions for Q/sub p/ approximately 0.5 are tau/sub E/ = 2 to 4 x 10 14 cm -3 s, = 10 to 20 keV, and E/sub beam/ = 500 to 1000 keV, with approximately 40% of the fusion energy produced by beam-target reactions. Illustrative parameters of LWHRs are compared with those of an ignited D-T reactor

General design and main problems of a gas-heavy-water power reactor contained in a pressure vessel; Conception generale et principaux problemes d'un reacteur de puissance eau lourde-gaz contenu dans un caisson resistant

Energy Technology Data Exchange (ETDEWEB)

Roche, R; Gaudez, J C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

In the framework of research carried out on a CO{sub 2}-cooled power reactor moderated by heavy water, the so-called 'pressure vessel' solution involves the total integration of the core, of the primary circuit (exchanges and blowers) and of the fuel handling machine inside a single, strong, sealed vessel made of pre-stressed concrete. A vertical design has been chosen: the handling 'attic' is placed above the core, the exchanges being underneath. This solution makes it possible to standardize the type of reactor which is moderated by heavy-water or graphite and cooled by a downward stream of carbon dioxide gas; it has certain advantages and disadvantages with respect to the pressure tube solution and these are considered in detail in this report. Extrapolation presents in particular.problems due specifically to the heavy water (for example its cooling,its purification, the balancing of the pressures of the heavy water and of the gas, the assembling of the internal structures, the height of the attic, etc. (authors) [French] Dans le cadre des etudes d'un reacteur de puissance modere a l'eau lourde et refroidi-au gaz carbonique, la solution dite 'en caisson' consiste en une integration totale du coeur, du circuit primaire (echangeurs et soufflantes) et du dispositif de manutention du combustible a l'interieur d'un meme caisson etanche et resistant en beton precontraint. La disposition envisagee est verticale; le grenier de manutention est dispose au-dessus du coeur, les echangeurs en dessous. Cette solution, qui permet d'uniformiser les types de reacteurs moderes a l'eau lourde ou au graphite et refroidis par une circulation descendante de gaz carbonique presente, par rapport a la solution a tube de force, des avantages et des inconvenients qui sont analyses dans cette etude. L'extrapolation pose, en particulier, des problemes specifiques a l'eau lourde (tels que son refroidissement, son epuration, l'equilibrage des pression entre l'eau lourde et le gaz, le montage

Feasibility study on thermal-hydraulic performance in tight-lattice rod bundles for reduced-moderation water reactors

International Nuclear Information System (INIS)

Ohnuki, A.; Kureta, M.; Liu, W.; Tamai, H.; Akimoto, H.

2004-01-01

Research and development project for investigating thermal-hydraulic performance in tight-lattice rod bundles for Reduced-Moderation Water Reactor (RMWR) started at Japan Atomic Energy Research Institute (JAERI) in 2002. The RMWR can attain the favorable characteristics such as effective utilization of uranium resources, multiple recycling of plutonium, high burn-up and long operation cycle, based on matured light-water reactor technologies. MOX fuel assemblies with tight lattice arrangement are used to increase the conversion ratio by reducing the moderation of neutron. Increasing the in-core void fraction also contributes to the reduction of neutron moderation. The confirmation of thermal-hydraulic feasibility is one of the most important issues for the RMWR because of the tight-lattice configuration. The project has mainly consisted of a large-scale thermal-hydraulic test and development of analytical methods named modeling engineering. In the large-scale test, 37-rod bundle experiments can be performed. Steady-state critical power experiments have been achieved in the test facility and the experimental data reveal the feasibility of RMWR

Operating experiences of reactor shutdown system at MAPS

International Nuclear Information System (INIS)

Kotteeswaran, T.J.; Subramani, V.A.; Hariharan, K.

1997-01-01

The reactors in Madras Atomic Power Station (MAPS), Kalpakkam are Pressurised Heavy Water Reactors (PHWR) similar to RAPS, Kota. The moderator heavy water is pumped into the calandria from dump tank to make the reactor critical. Later with the calandria level held constant at 92% FT, the further power changes are being done with the movement of adjuster rods. The moderator is held in calandria by means of helium gas pressure differential between top of calandria and dump tank located below. The shutdown of the reactor is effected by dumping the moderator water to dump tank by fast equalizing of helium gas pressure. In the revised mode of operation of moderator circuit after the moderator inlet manifold failure, the dump timing was observed to be more compared to the normal value. This was investigated and observed to be due to accumulation of D 2 O in the gas space above dump valves, which was affecting the helium equalizing flow. Also some of Indicating Alarm Meters (IAM) in protective system initiating the trip signals have failed in the unsafe mode. They have been modified to avoid the recurrence of the failures. (author)

Cirus reactor: a milestone in Indian Atomic Energy Programme

International Nuclear Information System (INIS)

Ranjan, Rakesh; Karhadkar, C.G.; Bhattacharya, S.

2017-01-01

Cirus, a 40 MW_t_h, high flux, thermal neutron research reactor achieved first criticality on 10"t"h July 1960. It had vertical core, natural metallic Uranium rods in Aluminium clad as fuel, demineralised light water as coolant, heavy water as moderator, Helium as cover gas and graphite as reflector. A low-pressure containment was provided for the reactor and some of the important associated reactor systems. Reactor start-up and power regulation was effected by controlled adjustment of moderator level in the reactor vessel. Boron carbide rods were used as primary shut down devices. Dumping of heavy water from core worked as secondary shut down device. Seawater was used as secondary coolant for removal of the fission heat of the reactor. Initial operation of Cirus was marred by several difficulties, primarily arising out of water chemistry in primary cooling water system. It took almost 3 years to systematically resolve these problems and achieve stable operation of reactor. Cirus could be operated at its rated power by the year 1963

RA Reactor operation and maintenance (I-IX), part V, Task 3.08/04-06, Refurbishment of the heavy water pumps

International Nuclear Information System (INIS)

Zecevic, V.; Nikolic, M.; Milic, J.

1963-12-01

In addition to detailed instructions for maintenance and repair of the heavy water pumps at the RA reactor this document includes nine annexes. They are as follows: cleaning the heavy water pump Avala with distilled water; instructions for repair of the pump CEN-132 (two annexes); list of operating characteristics of the pumps before repair; conclusions of the experts concerning the worn out bearings of the heavy water pump Avala, with the analysis of the stellite layer; report on the completed repair actions on the pumps Avala and CEN-132; report on the measurements done on the pump Avala; and the certificate concerning inspection of the pump

The high moderating ratio reactor using 100% MOX reloads

International Nuclear Information System (INIS)

Barbrault, P.

1994-06-01

This report presents the concept of a High Moderating ratio Reactor, which should accept 100% MOX reloads. This reactor aims to be the plutonium version of the European Pressurized Reactor (EPR), which is developed jointly by French and German companies. A moderating ration of 2.5 (instead of the standard value of 2.0) is obtained by replacing several fuel rods by water holes. The core would contain 241 Fuel Assemblies. We present some advantages of over-moderation for plutonium fuel, a description of the core and assemblies, calculations of fuel reload schemes and Reactivity Shutdown Margins, and the behavior of the core during two occidental transients. (author). 2 refs., 9 figs., 2 tabs

Pressure tube reactors

International Nuclear Information System (INIS)

Natori, Hisahide.

1981-01-01

Purpose: To improve the electrical power generation efficiency in a pressure tube reactor in which coolants and moderators are separated by feedwater heating with heat generated in heavy water and by decreasing the amount of steams to be extracted from the turbine. Constitution: A heat exchanger and a heavy water cooler are additionally provided to a conventional pressure tube reactor. The heat exchanger is disposed at the pre-stage of a low pressure feedwater heater series. High temperature heavy water heated in the core is passed through the primary side of the exchanger, while feedwater is passed through the secondary side. The cooler is disposed on the downstream of the heat exchanger in the flowing direction of the heavy water, in which heavy water from the heat exchanger is passed through the primary side and the auxiliary equipment cooling water is sent to the secondary side thereof. Accordingly, since extraction of heating steams is no more necessary, the steam can be used for the rotation of the turbine, and the electrical power generation efficiency can be improved. (Seki, T.)

The U.S. DOE new production reactor/heavy water reactor facility pollution prevention/waste minimization program

International Nuclear Information System (INIS)

Kaczmarsky, Myron M.; Tsang, Irving; Stepien, Walter P.

1992-01-01

A Pollution Prevention/Waste Minimization Program was established during the early design phase of the U.S. DOE's New Production Reactor/Heavy Water Reactor Facility (NPR/HWRF) to encompass design, construction, operation and decommissioning. The primary emphasis of the program was given to waste elimination, source reduction and/or recycling to minimize the quantity and toxicity of material before it enters the waste stream for treatment or disposal. The paper discusses the regulatory and programmatic background as it applies to the NPR/HWRF and the waste assessment program developed as a phased approach to pollution prevention/waste minimization for the NPR/HWRF. Implementation of the program will be based on various factors including life cycle cost analysis, which will include costs associated with personnel, record keeping, transportation, pollution control equipment, treatment, storage, disposal, liability, compliance and oversight. (author)

Status of advanced technology and design for water cooled reactors: Light water reactors

International Nuclear Information System (INIS)

1988-10-01

Water reactors represent a high level of performance and safety. They are mature technology and they will undoubtedly continue to be the main stream of nuclear power. There are substantial technological development programmes in Member States for further improving the technology and for the development of new concepts in water reactors. Therefore the establishment of an international forum for the exchange of information and stimulation of international co-operation in this field has emerged. In 1987 the IAEA established the International Working Group on Advanced Technologies for Water-Cooled Reactors (IWGATWR). Within the framework of IWGATWR the IAEA Technical Report on Status of Advanced Technology and Design for Water Cooled Reactors, Part I: Light Water Reactors and Part II: Heavy Water Reactors has been undertaken to document the major current activities and different trends of technological improvements and developments for future water reactors. Part I of the report dealing with LWRs has now been prepared and is based mainly on submissions from Member States. It is hoped that this part of the report, containing the status of advanced light water reactor design and technology of the year 1987 and early 1988 will be useful for disseminating information to Agency Member States and for stimulating international cooperation in this subject area. 93 refs, figs and tabs

IR analyzer spots heavy water leaks

International Nuclear Information System (INIS)

Anon.

1978-01-01

A correlation spectrometer developed by Barringer Research Ltd. (in collaboration with Atomic Energy of Canada and Ontario Hydro) is used to measure HDO concentrations in DTO in the final (distillation) stage of heavy-water production. A unit has been installed at Bruce Heavy Water Plant. Previously, such spectrometers had been installed to detect heavy-water leaks in CANDU reactors. The principle on which the instrument works is explained, with illustrations. It works by comparing the absorption at 2.9 μm, due to HDO, with that at 2.6 μm, due to both HDO and D 2 O. (N.D.H.)

Role of research and development in life management programme and upgradation of safety of Indian Pressurised Heavy Water Reactors

International Nuclear Information System (INIS)

Rupani, B.B.; Vijayan, P.K.; Rama Rao, A.; Sinha, R.K.

2009-01-01

At present, India has a fleet of thirteen small size 220 MWe Pressurised Heavy Water Reactors (PHWRs) and two medium size 540 MWe PHWRs. Reactor Engineering Division (RED) of Bhabha Atomic Research Centre (BARC) has pursued multi-faceted Research and Development programmes to support each phase of PHWR i.e. design, construction, commissioning, operation, maintenance, In-Service Inspection, repair and replacement and life extension, This programme is mainly related to life management of coolant channels, development of tooling and techniques for In-service Inspection of coolant channels, development of repair and replacement technology for coolant channels and moderator system, In-house development of technology and equipments like rolled joints to joint dissimilar metals and lancing equipment for steam generator and state-of art diagnostic systems for trouble shooting critical operating systems. The strong R and D support provided in the programme has significantly contributed towards safe operation of PHWRs. This paper gives the highlights of the major activities in above areas with their end uses and capability. (author)

Standard Guide for In-Service Annealing of Light-Water Moderated Nuclear Reactor Vessels

CERN Document Server

American Society for Testing and Materials. Philadelphia

2003-01-01

1.1 This guide covers the general procedures to be considered for conducting an in-service thermal anneal of a light-water moderated nuclear reactor vessel and demonstrating the effectiveness of the procedure. The purpose of this in-service annealing (heat treatment) is to improve the mechanical properties, especially fracture toughness, of the reactor vessel materials previously degraded by neutron embrittlement. The improvement in mechanical properties generally is assessed using Charpy V-notch impact test results, or alternatively, fracture toughness test results or inferred toughness property changes from tensile, hardness, indentation, or other miniature specimen testing (1). 1.2 This guide is designed to accommodate the variable response of reactor-vessel materials in post-irradiation annealing at various temperatures and different time periods. Certain inherent limiting factors must be considered in developing an annealing procedure. These factors include system-design limitations; physical constrain...

Application of noise analysis technique for monitoring the moderator temperature coefficient of reactivity in pressurized water reactors

International Nuclear Information System (INIS)

Shieh, D.J.; Upadhyaya, B.R.; Sweeney, F.J.

1987-01-01

A new technique, based on the noise analysis of neutron detector and core-exit coolant temperature signals, is developed for monitoring the moderator temperature coefficient of reactivity in pressurized water reactors (PWRs). A detailed multinodal model is developed and evaluated for the reactor core subsystem of the loss-of-fluid test (LOFT) reactor. This model is used to study the effect of changing the sign of the moderator temperature coefficient of reactivity on the low-frequency phase angle relationship between the neutron detector and the core-exit temperature noise signals. Results show that the phase angle near zero frequency approaches - 180 deg for negative coefficients and 0 deg for positive coefficients when the perturbation source for the noise signals is core coolant flow, inlet coolant temperature, or random heat transfer

Definition and Analysis of Heavy Water Reactor Benchmarks for Testing New Wims-D Libraries

International Nuclear Information System (INIS)

Leszczynski, Francisco

2000-01-01

This work is part of the IAEA-WIMS Library Update Project (WLUP). A group of heavy water reactor benchmarks have been selected for testing new WIMS-D libraries, including calculations with WIMSD5B program and the analysis of results.These benchmarks cover a wide variety of reactors and conditions, from fresh fuels to high burnup, and from natural to enriched uranium.Besides, each benchmark includes variations in lattice pitch and in coolants (normally heavy water and void).Multiplication factors with critical experimental bucklings and other parameters are calculated and compared with experimental reference values.The WIMS libraries used for the calculations were generated with basic data from JEF-2.2 Rev.3 (JEF) and ENDF/B-VI iNReleaseln 5 (E6) Results obtained with WIMS-86 (W86) library, included with WIMSD5B package, from Windfrith, UK with adjusted data, are included also, for showing the improvements obtained with the new -not adjusted- libraries.The calculations with WIMSD5B were made with two methods (input program options): PIJ (two-dimension collision probability method) and DSN (one-dimension Sn method, with homogenization of materials by ring).The general conclusions are: the library based on JEF data and the DSN meted give the best results, that in average are acceptable

Analysis of Removal Alternatives for the Heavy Water Components Test Reactor at the Savannah River Site

International Nuclear Information System (INIS)

Owen, M.B.

1996-08-01

This engineering study was developed to evaluate different options for decommissioning of the Heavy Water Components Test Reactor (HWCTR) at the Savannah River Site. This document will be placed in the DOE-SRS Area reading rooms for a period of 30 days in order to obtain public input to plans for the demolition of HWCTR

Multi-physical Developments for Safety Related Investigations of Low Moderated Boiling Water Reactors

OpenAIRE

Schlenker, Markus Thomas

2014-01-01

The main objective of this dissertation is the development and optimization of a low moderated boiling water reactor (BWR) core with improved fuel utilization to be incorporated in a Gen II BWR nuclear power plant. The assessment of the new core design is done by comparing it with a full MOX BWR core design regarding neutron physical and thermal-hydraulic design and safety criteria (e.g. inherent reactivity coefficients) and different sustainability parameters (e.g. conversion ratio).

Multi-physical developments for safety related investigations of low moderated boiling water reactors

Energy Technology Data Exchange (ETDEWEB)

Schlenker, Markus Thomas

2014-12-19

The main objective of this dissertation is the development and optimization of a low moderated boiling water reactor (BWR) core with improved fuel utilization to be incorporated in a Gen II BWR nuclear power plant. The assessment of the new core design is done by comparing it with a full MOX BWR core design regarding neutron physical and thermal-hydraulic design and safety criteria (e.g. inherent reactivity coefficients) and different sustainability parameters (e.g. conversion ratio).

Nuclear Reactor RA Safety Report, Vol. 4, Reactor

International Nuclear Information System (INIS)

1986-11-01

RA research reactor is thermal heavy water moderated and cooled reactor. Metal uranium 2% enriched fuel elements were used at the beginning of its operation. Since 1976, 80% enriched uranium oxide dispersed in aluminium fuel elements were gradually introduced into the core and are the only ones presently used. Reactor core is cylindrical, having diameter 40 cm and 123 cm high. Reaktor core is made up of 82 fuel elements in aluminium channels, lattice is square, lattice pitch 13 cm. Reactor vessel is cylindrical made of 8 mm thick aluminium, inside diameter 140 cm and 5.5 m high surrounded with neutron reflector and biological shield. There is no containment, the reactor building is playing the shielding role. Three pumps enable circulation of heavy water in the primary cooling circuit. Degradation of heavy water is prevented by helium cover gas. Control rods with cadmium regulate the reactor operation. There are eleven absorption rods, seven are used for long term reactivity compensation, two for automatic power regulation and two for safety shutdown. Total anti reactivity of the rods amounts to 24%. RA reactor is equipped with a number of experimental channels, 45 vertical (9 in the core), 34 in the graphite reflector and two in the water biological shield; and six horizontal channels regularly distributed in the core. This volume include detailed description of systems and components of the RA reactor, reactor core parameters, thermal hydraulics of the core, fuel elements, fuel elements handling equipment, fuel management, and experimental devices [sr

Research reactors

International Nuclear Information System (INIS)

Kowarski, L.

1955-01-01

It brings together the techniques data which are involved in the discussion about the utility for a research institute to acquire an atomic reactor for research purposes. This type of decision are often taken by non-specialist people who can need a brief presentation of a research reactor and its possibilities in term of research before asking advises to experts. In a first part, it draws up a list of the different research programs which can be studied by getting a research reactor. First of all is the reactor behaviour and kinetics studies (reproducibility factor, exploration of neutron density, effect of reactor structure, effect of material irradiation...). Physical studies includes study of the behaviour of the control system, studies of neutron resonance phenomena and study of the fission process for example. Chemical studies involves the study of manipulation and control of hot material, characterisation of nuclear species produced in the reactor and chemical effects of irradiation on chemical properties and reactions. Biology and medicine research involves studies of irradiation on man and animals, genetics research, food or medical tools sterilization and neutron beams effect on tumour for example. A large number of other subjects can be studied in a reactor research as reactor construction material research, fabrication of radioactive sources for radiographic techniques or applied research as in agriculture or electronic. The second part discussed the technological considerations when choosing the reactor type. The technological factors, which are considered for its choice, are the power of the reactor, the nature of the fuel which is used, the type of moderator (water, heavy water, graphite or BeO) and the reflector, the type of coolants, the protection shield and the control systems. In the third part, it described the characteristics (place of installation, type of combustible and comments) and performance (power, neutron flux ) of already existing

Level-1 probability safety assessment of the Iranian heavy water reactor using SAPHIRE software

International Nuclear Information System (INIS)

Faghihi, F.; Ramezani, E.; Yousefpour, F.; Mirvakili, S.M.

2008-01-01

The main goal of this review paper is to analyze the total frequency of the core damage of the Iranian Heavy Water Research Reactor (IHWRR) compared with standard criteria and to determine the strengths and the weaknesses of the reactor safety systems towards improving its design and operation. The PSA has been considered for full-power state of the reactor and this article represents a level-1 PSA analysis using System Analysis Programs for Hands-On Integrated Reliability Evaluations (SAPHIRE) software. It is specifically designed to permit a listing of the potential accident sequences, compute their frequencies of occurrence and assign each sequence to a consequence. The method used for modeling the systems and accident sequences, is Large Fault Tree/Small Event Tree method. This PSA level-1 for IHWRR indicates that, based on conservative assumptions, the total frequency of accidents that would lead to core damage from internal initiating events is 4.44E-05 per year of reactor operation

Level-1 probability safety assessment of the Iranian heavy water reactor using SAPHIRE software

Energy Technology Data Exchange (ETDEWEB)

Faghihi, F. [Department of Nuclear Engineering, School of Engineering, Shiraz University, 71348-51153 Shiraz (Iran, Islamic Republic of); Research Center for Radiation Protection, Shiraz University, Shiraz (Iran, Islamic Republic of); Nuclear Safety Research Center, Shiraz University, Shiraz (Iran, Islamic Republic of)], E-mail: faghihif@shirazu.ac.ir; Ramezani, E. [Department of Nuclear Engineering, School of Engineering, Shiraz University, 71348-51153 Shiraz (Iran, Islamic Republic of); Yousefpour, F. [Atomic Energy Organization of Iran (AEOI), Tehran (Iran, Islamic Republic of); Mirvakili, S.M. [Department of Nuclear Engineering, School of Engineering, Shiraz University, 71348-51153 Shiraz (Iran, Islamic Republic of)

2008-10-15

The main goal of this review paper is to analyze the total frequency of the core damage of the Iranian Heavy Water Research Reactor (IHWRR) compared with standard criteria and to determine the strengths and the weaknesses of the reactor safety systems towards improving its design and operation. The PSA has been considered for full-power state of the reactor and this article represents a level-1 PSA analysis using System Analysis Programs for Hands-On Integrated Reliability Evaluations (SAPHIRE) software. It is specifically designed to permit a listing of the potential accident sequences, compute their frequencies of occurrence and assign each sequence to a consequence. The method used for modeling the systems and accident sequences, is Large Fault Tree/Small Event Tree method. This PSA level-1 for IHWRR indicates that, based on conservative assumptions, the total frequency of accidents that would lead to core damage from internal initiating events is 4.44E-05 per year of reactor operation.

Heavy water technology and its contribution to energy sustainability

International Nuclear Information System (INIS)

MacDiarmid, H.; Alizadeh, A.; Hopwood, J.; Duffey, R.

2009-01-01

Full text: As the global nuclear industry expands several markets are exploring avenues and technologies to underpin energy security. Heavy water reactors are the most versatile power reactors in the world. They have the potential to extend resource utilization significantly, to allow countries with developing industrial infrastructures access to clean and abundant energy, and to destroy long-lived nuclear waste. These benefits are available by choosing from an array of possible fuel cycles. Several factors, including Canada's early focus on heavy-water technology, limited heavy-industry infrastructure at the time, and a desire for both technological autonomy and energy self-sufficiency, contributed to the creation of the first commercial heavy water reactor in 1962. With the maturation of the industry, the unique design features of the now-familiar product-on-power refuelling, high neutron economy, and simple fuel design-make possible the realization of its potential fuel-cycle versatility. As resource constrains apply pressure on world markets, the feasibility of these options have become more attractive and closer to entering widespread commercial application

Development of a silicon calorimeter for dosimetry applications in a water-moderated reactor

International Nuclear Information System (INIS)

DePriest, Kendall Russell; King, Donald Bryan; Naranjo, Gerald E.; Luker, Spencer Michael; Keltner, Ned R.; Suo-Anttila, Ahti Jorma; Griffin, Patrick Joseph

2005-01-01

High fidelity active dosimetry in the mixed neutron/gamma field of a research reactor is a very complex issue. For passive dosimetry applications, the use of activation foils addresses the neutron environment while the use of low neutron response CaF 2 :Mn thermoluminescent dosimeters (TLDs) addresses the gamma environment. While radiation-hardened diamond photoconducting detectors (PCD) have been developed that provide a very precise fast response (picosecond) dosimeter and can provide a time-dependent profile for the radiation environment, the mixed field response of the PCD is still uncertain and this interferes with the calibration of the PCD response. In order to address the research reactor experimenter's need for a dosimeter that reports silicon dose and dose rate at a test location during a pulsed reactor operation, a silicon calorimeter has been developed. This dosimeter can be used by itself to provide a dose in rad(Si) up to a point in a reactor pulsed operation, or, in conjunction with the diamond PCD, to provide a dose rate. This paper reports on the development, testing, and validation of this silicon calorimeter for applications in water-moderated research reactors.

Problems related with the power regulation of reactors by physico-chemical methods, and the behaviour of water and heavy water in nuclear reactors; Comportement de l'eau et de l'eau lourde dans les reacteurs nucleaires et problemes de la regulation de puissance par voie physico-chimique

Energy Technology Data Exchange (ETDEWEB)

Dolle, L; Conan, D; Dirian, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Experience of the CEA heavy water reactors and a systematic study of the radiolytic decomposition of water in the core of swimming-pool reactors are described. Setting up of reactivity control by physico-chemical methods. Reactivity control by homogeneous poisoning of the reactor A comparison of the evolution of xenon poisoning with the residual anti reactivity of the poison in solution during its nuclear consumption establishes the programme which must govern the variation in its concentration if the exact compensation is to be produced The behaviour of the poison towards the reactor materials under the particular operational conditions must be taken into account. Radiolytic decomposition of water in the reactors in the presence of soluble poisons: A study of the effect of certain chemically inert salts, present in small concentrations in the water, on its radiolytic decomposition rate, has led to some new results which are discussed. The choice of a soluble poison is justified on the basis of the above results. Reactivity control by the use of a gaseous absorbent The use of a gas control rod circuit for compensation purposes, in place of solid control rods is described. The use of soluble poisons in the moderator to compensate the xenon effect, and of a gaseous absorbent in a circuit known as a gas control rod form original aspects of the reactivity control in the reactor EL 4. (authors) [French] L'observation du comportement de l'eau et de l'eau lourde dans les reacteurs en exploitation, contribue au fonctionnement sur de ceux-ci et oriente certaines etudes relatives aux techniques de controle de la reactivite par mise en oeuvre de poisons solubles. L'utilisation de poisons nucleaires dissous dans l'eau du reacteur entraine une pollution chimique de celle-ci. Les conditions d'emploi permettant d'eviter les effets indesirables de cette pollution sont etudiees. Les problemes analytiques - bien qu'importants - ne sont pas abordes dans le cadre de la communication

Fuel to Moderator Ratio Sensitivity Study Using Water Rod Moderator in SCWR Conceptual Core Design

International Nuclear Information System (INIS)

Bae, Seong Man; Kim, Yong Bae; Park, Dong Hwan; Lee, Kwang Ho

2009-01-01

The conceptual operating condition of Super Critical Water-cooled Reactor (SCWR) is above critical point of water, such that the coolant temperature ranges from 280 .deg. C to 510 .deg. C with a pressure of 25MPa. This operating condition makes an SCWR have both merits and demerits when compared with current Light Water Reactors (LWRs). One of the demerits of SCWR is degradation of neutron moderation due to a lower water density from ∼0.1g/cm 3 to ∼0.7g/cm 3 under a high coolant temperature condition. Therefore it is necessary to enhance the moderation capability for SCWR to slow down the fast fission neutrons. Many SCWR designs have a water rod concept as an additional moderator, because water has a good moderation capability. Through reviewing the previous water rod assembly designs, it was identified that a sensitivity study is required to optimize fuel assembly pitch to increase the neutron economy. In this paper, the results of the conceptual assembly design sensitivity study which focuses on the comparison of sensitivity for the fuel pitch to diameter (P/D) ratio using water rod moderator, are presented

NORA project offers unique reactor research and advanced training opportunities

International Nuclear Information System (INIS)

1961-01-01

An international program for reactor research and advanced training for a period of three years has been established in connection with the Norwegian critical assembly NORA. The aim of the project is to determine, through integral experiments, the basic reactor physics data for lattices moderated with light-water, heavy-water or mixtures of heavy and light water, with fuels of different sizes and spacing, three different enrichments and compositions. The objectives, programme, and facilities are described in details

Zero energy reactor 'RB'

Energy Technology Data Exchange (ETDEWEB)

Popovic, D; Takac, S; Markovic, H; Raisic, N; Zdravkovic, Z; Radanovic, Lj [Boris Kidric Institute of Nuclear Sciences, Vinca, Beograd (Yugoslavia)

1959-03-15

In 1958 the zero energy reactor RB was built with the purpose of enabling critical experiments with various reactor systems to be carried out. The first core assembly built in this reactor consists of heavy water as moderator and natural uranium metal as fuel. In order to be able to obtain very accurate results when measuring the main characteristics of the assembly the reactor was built as a completely bare system. (author)

Heavy water pumps; Pumpe D{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Zecevic, V; Nikolic, M

1963-12-15

Continuous increase of radiation intensity was observed on all the elements in the heavy water system during first three years of RA reactor operation. The analysis of heavy water has shown the existence of radioactive cobalt. It was found that cobalt comes from stellite, cobalt based alloy which was used for coating of the heavy water pump discs in order to increase resistance to wearing. Cobalt was removed from the surfaces due to friction, and transferred by heavy water into the reactor where it has been irradiated for 29 876 MWh up to 8-15 Ci/g. Radioactive cobalt contaminated all the surfaces of aluminium and stainless steel parts. This report includes detailed description of heavy water pumps repair, exchange of stellite coated parts, decontamination of the heavy water system, distillation of heavy water. [Serbo-Croat] U toku prve tri godine eksploatacije reaktora RA uocen je neprekidni porast intenziteta zracenja na svim elementima u teskovodnom sistemu. Analizom teske vode utvrdjeno je postojanje radioaktivnog kobalta. Ustanovljeno je da kobalt potice od stelita, legure na bazi kobalta kojim su presvuceni rukavci vratila teskovodnih pumpi radi otpornosi na habanje. Kobalt je trenjem skidan sa povrsina, u toku rada prenosen je teskom vodom u reaktor i ozracivan u toku 29 876 MWh do specificne aktivnosti 8-15 Ci/g. Radioaktivni kobalt je kontaminirao sve povrsine od aluminijuma i nerdjajuceg celika. Ovaj izvestaj sadrzi detaljan opis remonta pumpi, zamene delova teskovodnih pumpi novim delovima bez stelitnog sloja, dekontaminacije teskovodnog sistema, destilacije teske vode.

Application of hydrogen water chemistry to moderate corrosive circumstances around the reactor pressure vessel bottom of boiling water reactors

International Nuclear Information System (INIS)

Uchida, Shunsuke; Ibe, Eishi; Nakata, Kiyatomo; Fuse, Motomasa; Ohsumi, Katsumi; Takashima, Yoshie

1995-01-01

Many efforts to preserve the structural integrity of major piping, components, and structures in a boiling water reactor (BWR) primary cooling system have been directed toward avoiding intergranular stress corrosion cracking (IGSCC). Application of hydrogen water chemistry (HWC) to moderate corrosive circumstances is a promising approach to preserve the structural integrity during extended lifetimes of BWRs. The benefits of HWC application are (a) avoiding the occurrence of IGSCC on structural materials around the bottom of the crack growth rate, even if microcracks are present on the structural materials. Several disadvantage caused by HWC are evaluated to develop suitable countermeasures prior to HWC application. The advantages and disadvantages of HWC are quantitatively evaluated base on both BWR plant data and laboratory data shown in unclassified publications. Their trade-offs are discussed, and suitable applications of HWC are described. It is concluded that an optimal amount of Hydrogen injected into the feedwater can moderate corrosive circumstances, in the region to be preserved, without serious disadvantages. The conclusions have been drawn by combining experimental and theoretical results. Experiments in BWR plants -- e.g., direct measurements of electrochemical corrosion potential and crack growth rate at the RPV bottom -- are planned that would collect data to support the theoretical considerations

Management of radioactive wastes at power reactor sites in India

International Nuclear Information System (INIS)

Amalraj, R.V.; Balu, K.

Indian nuclear power programme, at the present stage, is based on natural uranium fuelled heavy water moderated CANDU type reactors except for the first nuclear power station consisting of two units of enriched uranium fuelled, light water moderated, BWR type of reactors. Some of the salient aspects of radioactive waste management at power reactor sites in India are discussed. Brief reviews are presented on treatment of wastes, their disposal and environmental aspects. Indian experience in power reactor waste management is also summarised identifying some of the areas needing further work. (auth.)

Evaluation of A-1 reactor heavy-water calandria specimens

International Nuclear Information System (INIS)

Brumovsky, M.

1976-01-01

Container chains with surveillance specimens were placed in two special channels of the core peripheral part to test changes in mechanical properties due to reactor operation of caisson tube material. The specimens were made from the caisson tube material and placed by eight pieces on the outer surface of the containers. The first removed specimens were tested for corrosion losses, tensile strength, and fractured surfaces were then assessed. The changes in strength properties were found to be similar in both base material and welded joints. The corrosion film on surveillance specimens did not practically affect strength properties nor ductility. It was found that the Al-Mg-Si alloy used for the heavy water vessel caisson tubes following stabilization annealing was fully stable at operating temperatures of up to 100 degC. Slio.ht changes in properties can be attributed to the effect of a high neutron dose. Thus, the high radiation and temperature stability of the alloy was confirmed. (O.K.)

Various analytical techniques used for the measurement of isotopic purity of heavy water at Madras Atomic Power Station

International Nuclear Information System (INIS)

Satyanarayanan, V.; Umapathy, P.; Bhaskaran, R.; Nagarajan, J.; Pradeep, Jeena; Ayyar, S.R.

2008-01-01

The paper deals with the various techniques used for the measurement of isotopic purity of heavy water samples received from different sources viz. reactor systems, heavy water upgrading plant and fresh consignment from heavy water production plants. Heavy water is used in PHWRs as moderator and primary coolant. Isotopic Purity is an important parameter to be monitored/analysed regularly for both the systems. There is a minimum isotopic purity level to be maintained in the moderator system due to neutron economy/fuel burnup and in the case of coolant system the measurement is of paramount importance due to its safety considerations. The selection of the method of analysis depends on the isotopic range. The techniques used to measure the isotopic purity of heavy water are a) Infrared Spectrophotometry b) Refractometry c) Densitometry. Infrared spectrometer uses the property of molecular absorption of IR radiation by HOD species and the absorbance is the measure of isotopic purity. This technique is generally used for measuring high isotopic (80-99.98%) and low isotopic samples. Refractometer uses the property of refractive index of heavy water. The difference in refractive indices of light water and heavy water is 0.0048. A 1 % change in D 2 O concentration would thus equal to 0.000048 refractive index units. This method is used for determining the approximate isotopic value of a sample. Density meter uses the property of difference in densities of light and heavy water. The difference in density of 99.999% D 2 O and light water is 0.107540 which covers the whole range of interest. The experience gained with these techniques in the measurements of isotopic purity of various samples are presented in this paper. (author)

General design and main problems of a gas-heavy-water power reactor contained in a pressure vessel; Conception generale et principaux problemes d'un reacteur de puissance eau lourde-gaz contenu dans un caisson resistant

Energy Technology Data Exchange (ETDEWEB)

Roche, R.; Gaudez, J.C. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

In the framework of research carried out on a CO{sub 2}-cooled power reactor moderated by heavy water, the so-called 'pressure vessel' solution involves the total integration of the core, of the primary circuit (exchanges and blowers) and of the fuel handling machine inside a single, strong, sealed vessel made of pre-stressed concrete. A vertical design has been chosen: the handling 'attic' is placed above the core, the exchanges being underneath. This solution makes it possible to standardize the type of reactor which is moderated by heavy-water or graphite and cooled by a downward stream of carbon dioxide gas; it has certain advantages and disadvantages with respect to the pressure tube solution and these are considered in detail in this report. Extrapolation presents in particular.problems due specifically to the heavy water (for example its cooling,its purification, the balancing of the pressures of the heavy water and of the gas, the assembling of the internal structures, the height of the attic, etc. (authors) [French] Dans le cadre des etudes d'un reacteur de puissance modere a l'eau lourde et refroidi-au gaz carbonique, la solution dite 'en caisson' consiste en une integration totale du coeur, du circuit primaire (echangeurs et soufflantes) et du dispositif de manutention du combustible a l'interieur d'un meme caisson etanche et resistant en beton precontraint. La disposition envisagee est verticale; le grenier de manutention est dispose au-dessus du coeur, les echangeurs en dessous. Cette solution, qui permet d'uniformiser les types de reacteurs moderes a l'eau lourde ou au graphite et refroidis par une circulation descendante de gaz carbonique presente, par rapport a la solution a tube de force, des avantages et des inconvenients qui sont analyses dans cette etude. L'extrapolation pose, en particulier, des problemes specifiques a l'eau lourde (tels que son refroidissement, son epuration

Fluid moderator control system reactor internals distribution system

International Nuclear Information System (INIS)

Fensterer, H.F.; Klassen, W.E.; Veronesi, L.; Boyle, D.E.; Salton, R.B.

1987-01-01

This patent describes a spectral shift pressurized water nuclear reactor employing a low neutron moderating fluid for the spectral shift including a reactor pressure vessel, a core comprising a plurality of fuel assemblies, a core support plate, apparatus comprising means for penetrating the reactor vessel for introducing the moderating fluid into the reactor vessel. Means associated with the core support plate for directly distributing the moderating fluid to and from the fuel assemblies comprises at least one inlet flow channel in the core plate; branch inlet feed lines connect to the inlet flow channel in the core plate; vertical inlet flow lines flow connected to the branch inlet feed lines; each vertical flow line communicates with a fuel assembly; the distribution means further comprise lines serving as return flow lines, each of which is connected to one of the fuel assemblies; branch exit flow lines in the core plate flow connected to the return flow lines of the fuel assembly; and at least one outlet flow channel flow connected to the branch exit flow lines; and a flow port interposed between the penetration means and the distribution means for flow connecting the penetration means with the distribution means

Expansion connection of socket in flow distributed cabin of heavy water research reactor inner shell

International Nuclear Information System (INIS)

Jiang Zhiliang; Li Yanshui

1995-01-01

Expansion connection of aluminium alloy LT21 socket in flow distributed cabin of Heavy Water Research Reactor (HWRR) inner shell is described systematically. The expansion connection technology parameters of products are determined through tests. They are as following: bounce value of inner diameter after expansion, expansion degree, space between socket and plate hole, device for expanding pipes, selection of tools for enlarging or reaming holes, manufacture for socket inner hole and cleaning after expansion

Measurement of the heavy water level in the fuel channels of the RA reactor - Annex 11; Prilog 11- Merenje nivoa teske vode u gorivnim kanalima reaktora RA

Energy Technology Data Exchange (ETDEWEB)

Nikolic, M [Institute of Nuclear Sciences Boris Kidric, Reaktor RA, Vinca, Beograd (Serbia and Montenegro)

1964-12-15

The objective of measuring the heavy water level in the reactor channels was to verify experimentally the possibilities of reactor cooling with parallel operation of heavy water pumps od 1500 rotations/min at nominal power of 6.5 MW. Measurements were done in 2 periphery and 2 central fuel channels with pumps speed 1500, 1800 and 3000 rotations/min by a contact probe with electric resistance measuring device. precision of the measurement was {+-}1 cm.

Development of in-situ laser based cutting technique for shock absorber rear nut in pressurized heavy water reactors. CP-2.1

International Nuclear Information System (INIS)

Vishwakarma, S.C.; Jain, R.K.; Upadhyaya, B.N.; Choubey, Ambar; Agrawal, D.K.; Oak, S.M.

2007-01-01

We have developed a laser based cutting technique for shock absorber rear nuts in pressurized heavy water reactors (PHWRs). This technique has been successfully used for in-situ laser cutting at RAPS-3 reactor. The technique consists of a motorized compact fixture, which holds a fiber optic beam delivery cutting nozzle and can be operated remotely

State space modeling of reactor core in a pressurized water reactor

Energy Technology Data Exchange (ETDEWEB)

Ashaari, A.; Ahmad, T.; M, Wan Munirah W. [Department of Mathematical Science, Faculty of Science, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Shamsuddin, Mustaffa [Institute of Ibnu Sina, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Abdullah, M. Adib [Swinburne University of Technology, Faculty of Engineering, Computing and Science, Jalan Simpang Tiga, 93350 Kuching, Sarawak (Malaysia)

2014-07-10

The power control system of a nuclear reactor is the key system that ensures a safe operation for a nuclear power plant. However, a mathematical model of a nuclear power plant is in the form of nonlinear process and time dependent that give very hard to be described. One of the important components of a Pressurized Water Reactor is the Reactor core. The aim of this study is to analyze the performance of power produced from a reactor core using temperature of the moderator as an input. Mathematical representation of the state space model of the reactor core control system is presented and analyzed in this paper. The data and parameters are taken from a real time VVER-type Pressurized Water Reactor and will be verified using Matlab and Simulink. Based on the simulation conducted, the results show that the temperature of the moderator plays an important role in determining the power of reactor core.

Development of an automated system of nuclear materials accounting for nuclear power stations with water-cooled, water-moderated reactors

International Nuclear Information System (INIS)

Babaev, N.S.

1981-06-01

The results of work carried out under IAEA Contract No. 2336/RB are described (subject: an automated system of nuclear materials accounting for nuclear power stations with water-cooled, water-moderated (VVER) reactors). The basic principles of an accounting system for this type of nuclear power plant are outlined. The general structure and individual units of the information computer program used to achieve automated accounting are described and instructions are given on the use of the program. A detailed example of its application (on a simulated nuclear power plant) is examined

Aiming at super long term application of nuclear energy. Scope and subjects on the water cooled breeder reactor, the 'reduced moderation water reactor'

International Nuclear Information System (INIS)

Sato, Osamu; Tatematsu, Kenji; Tanaka, Yoji

2001-01-01

In order to make possible on nuclear energy application for super long term, development of sodium cooling type fast breeder reactor (FBR) has been carried out before today. However, as it was found that its commercialization was technically and economically difficult beyond expectation, a number of nations withdrew from its development. And, as Japan has continued its development, scope of its actual application is not found yet. Now, a research and development on a water cooling type breeder reactor, the reduced moderation water reactor (RMWR)' using LWR technology has now been progressed under a center of JAERI. This RMWR is a reactor intending a jumping upgrade of conversion ratio by densely arranging fuel bars to shift neutron spectrum to faster region. The RMWR has a potential realizable on full-dress plutonium application at earlier timing through its high conversion ratio, high combustion degree, plutonium multi-recycling, and so on. And, it has also feasibility to solve uranium resource problem by realization of conversion ratio with more than 1.0, to contribute to super long term application of nuclear energy. Here was investigated on an effect of reactor core on RMWR, especially of its conversion ratio and plutonium loading on introduction effect as well as on how RMWR could be contributed to reduction of uranium resource consumption, by drawing some scenario on development of power generation reactor and fuel cycle in Japan under scope of super long term with more than 100 years in future. And, trial calculation on power generation cost of the RMWR was carried out to investigate some subjects at a viewpoint of upgrading on economy. (G.K.)

A study on criticality of coupled fast-thermal core HERBE at RB reactor

Energy Technology Data Exchange (ETDEWEB)

Pesic, M; Zavaljevski, M; Milosevic, M; Stefanovic, D; Nikolic, D; Avdic, S [Boris Kidric Institute of Nuclear Sciences, Vinca, Belgrade (Yugoslavia); Popovic, D; Marinkovic, P [Faculty of Electrical Engineering, Beograd (Yugoslavia)

1991-07-01

The coupled fast-thermal core HERBE at the RB zero power heavy water reactor in Vinca was designed with the aim of improving the experimental possibilities in fast neutron fields. The requirements for minimum modifications in the RB construction and the use available fuel, restricted design flexibility of the coupled system. The following core is considered optimal in the light of the foregoing constraints: the central fast core of natural uranium is surrounded by a neutron filter zone (cadmium and natural uranium) and a converter zone (enriched uranium fuel, without moderator). The coupling region is heavy water. The thermal core in the form of the RB heavy water 80% enriched uranium lattice with 12 cm pitch. The criticality of the system is obtained by adjusting the moderator level. The critical heavy water levels were measured for normal reactor operation and some simulated accidental conditions. These data were analyzed by a computer code for the design of thermal and coupled fast-thermal reactor recently developed in IBK Nuclear Engineering Laboratory. Good agreement between the computations and experimental data was achieved. (author)

A study on criticality of coupled fast-thermal core HERBE at RB reactor

International Nuclear Information System (INIS)

Pesic, M.; Zavaljevski, M.; Milosevic, M.; Stefanovic, D.; Nikolic, D.; Avdic, S.; Popovic, D.; Marinkovic, P.

1991-01-01

The coupled fast-thermal core HERBE at the RB zero power heavy water reactor in Vinca was designed with the aim of improving the experimental possibilities in fast neutron fields. The requirements for minimum modifications in the RB construction and the use available fuel, restricted design flexibility of the coupled system. The following core is considered optimal in the light of the foregoing constraints: the central fast core of natural uranium is surrounded by a neutron filter zone (cadmium and natural uranium) and a converter zone (enriched uranium fuel, without moderator). The coupling region is heavy water. The thermal core in the form of the RB heavy water 80% enriched uranium lattice with 12 cm pitch. The criticality of the system is obtained by adjusting the moderator level. The critical heavy water levels were measured for normal reactor operation and some simulated accidental conditions. These data were analyzed by a computer code for the design of thermal and coupled fast-thermal reactor recently developed in IBK Nuclear Engineering Laboratory. Good agreement between the computations and experimental data was achieved. (author)

Electrolytic process for upgrading heavy water (Preprint No. PD-16)

International Nuclear Information System (INIS)

Rammohan, K.; Sadhukhan, H.K.

1989-04-01

In the reactor system the heavy water gets depleted in concentration due to leakages, intermixing and vapour collection in boiler vault system etc. Electrolysis of water was used as a secondary plant to enrich the dilute heavy water produced in the primery plant by hydrogen-sulfide-water exchange process. The studies made in the development of this process for the upgrading of downgra ded heavy water by setting up a full size Electrolyser Test Assembly are discussed a nd complete design of a heavy water upgrading plant based on electrolytic process for MAPS and NAPP is described. (author). 7 refs., 5 figs

Water chemistry management of research reactor in JAERI

Energy Technology Data Exchange (ETDEWEB)

Yoshijima, Tetsuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-10-01

The JRR-3M cooling system consists of four systems, namely; (1) primary cooling system, (2) heavy water cooling system, (3) helium system and (4) secondary cooling system. The heavy water is used for reflector and pressurized with helium gas. Water chemistry management of the JRR-3M cooling systems is one of the important subject for the safety operation. The main objects are to prevent the corrosion of cooling system and fuel elements, to suppress the plant radiation build-up and to minimize the generation of radioactive waste. All measured values were within the limits of specifications and JRR-3M reactor was operated with safety in 1996. Spent fuels of JRR-3M reactor are stored in the spent fuel pool. This pool water has been analyzed to prevent corrosion of aluminum cladding of spent fuels. Water chemistry of spent fuel pool water is applied to the prevention of corrosion of aluminum alloys including fuel cladding. The JRR-2 reactor was eternally stopped in December 1996 and is now under decommissioning. The JRR-2 reactor is composed of heavy water tank, fuel guide tube and horizontal experimental hole. These are constructed of aluminum alloy and biological shield and upper shield are constructed of concrete. Three types of corrosion of aluminum alloy were observed in the JRR-2. The Alkaline corrosion of aluminum tube occurred in 1972 because of the mechanical damage of the aluminum fuel guide tube which is used for fuel handling. Modification of the reactor top shield was started in 1974 and completed in 1975. (author)

Plutonium fuel cycles in the spectral shift controlled reactor

International Nuclear Information System (INIS)

Sider, F.M.; Matzie, R.A.

1980-01-01

The spectral shift controlled reactor (SSCR) controls excess core reactivity during an operating cycle through the use of variable heavy water concentrations in the moderator. With heavy water in the coolant, the neutron spectrum is shifted to higher energy levels, thus increasing fertile conversion. In addition, since heavy water obviates the need for soluble boron, neutron losses to control poison are eliminated. As a result, better resource utilization is obtained in the SSCR employing plutonium fuel cycles compared to similarly fueled pressurized water reactors (PWRs). The SSCR, however, is not competitive with the PWR due to higher capital costs, operation and maintenance costs, and the heavy water costs, which outweigh the fuel cycle cost savings. The SSCR may become an attractive alternative to the PWR if uranium prices increase substantially

Behaviour of heavy water in nuclear reactors of the CEA; Comportement de l'eau lourde dans les piles du C.E.A

Energy Technology Data Exchange (ETDEWEB)

Chenouard, J; Dirian, G; Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

In the two heavy water reactors of the CEA: Zoe and P-2, we do: A) the supervision of the isotopic composition of the heavy water; B) the supervision of gases released by the decomposition of the heavy water under radiation, and to their recombination; C) periodic analyses of impurities. (M.B.) [French] Dans les deux piles a eau lourde du Commissariat a l'Energie Atomique: Zoe et P 2, nous effectuons: A) la surveillance de la composition isotopique de l'eau lourde; B) la surveillance des gaz degages par la decomposition de l'eau lourde sous radiation, et a leur recombinaison; C) des analyses periodiques d'impuretes. (M.B.)

Analytical modelling and study of the stability characteristics of the Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Nayak, A.K.; Vijayan, P.K.; Saha, D.

2000-04-01

An analytical model has been developed to study the thermohydraulic and neutronic-coupled density-wave instability in the Indian Advanced Heavy Water Reactor (AHWR) which is a natural circulation pressure tube type boiling water reactor. The model considers a point kinetics model for the neutron dynamics and a lumped parameter model for the fuel thermal dynamics along with the conservation equations of mass, momentum and energy and equation of state for the coolant. In addition, to study the effect of neutron interactions between different parts of the core, the model considers a coupled multipoint kinetics equation in place of simple point kinetics equation. Linear stability theory was applied to reveal the instability of in-phase and out-of-phase modes in the boiling channels of the AHWR. The results indicate that the design configuration considered may experience both Ledinegg and Type I and Type II density-wave instabilities depending on the operating condition. Some methods of suppressing these instabilities were found out. In addition, it was found that the stability behavior of the reactor is greatly influenced by the void reactivity coefficient, fuel time constant, radial power distribution and channel inlet orificing. The delayed neutrons were found to have strong influence on the Type I and Type II instabilities. Decay ratio maps were predicted considering various operating parameters of the reactor, which are useful for its design. (author)

From a critical assembly heavy water - natural uranium to the fast - thermal research reactor in the Institute Vinca

International Nuclear Information System (INIS)

Stefanovic, D.; Pesic, M.

1995-01-01

A part of the Institute in Vinca this monograph refers to is the thermal nuclear zero power reactor RB, with a heavy water moderator and variously enriched uranium fuel, that is, its present day version, the coupled fast-thermal system HERBE. A group of research workers, technicians, operators and skilled workmen in the workshop have worked continuously on it. Some of them have spent their whole working age at the reactor, and some a part of it. There is about a hundred and fifty internationally published papers, twenty master's and fourteen doctor's theses left behind them for the past thirty five years. This book is devoted to them. The first part of the text refers to the pioneering efforts on the reactor and fundamental research in reactor physics. The experimental reactor RB was designed and constructed at the time to operate with natural uranium and heavy water. Measurements are presented and the first results of reaching critical state, measurements of migration length of thermal neutrons and neutron multiplication factor in an infinite medium; also measurements of neutron flux density distribution and reactor parameter, and in the domain of safety, measurement of safety rods reactivity. Those were also the times when the known serious accident occurred with the uncontrolled rise of reactivity, which was especially minutely described in a publication of the International Atomic Energy Agency from Vienna. Later on, new fuel was acquired with 2 % enriched uranium. A series of experiments in reactor and neutron physics followed, with just the most interesting results of them presented here. In the period which followed, another type of fuel was available, with 80 % enriched uranium. New possibilities for work opened. Measurements with mixed lattices were performed, and the RA reactor lattices were simulated. After measurements mainly in the sphere of reactor and neutron physics, a need for investigations in the field of gamma and neutron radiation protection

Feasibility study of self sustaining capability on water cooled thorium reactors for different power reactors

International Nuclear Information System (INIS)

Permana, S.; Takaki, N.; Sekimoto, H.

2007-01-01

Thorium fuel cycle can maintain the sustainable system of the reactor for self sustaining system for future sustainable development in the world. Some characteristics of thorium cycle show some advantages in relation to higher breeding capability, higher performance of burn-up and more proliferation resistant. Several investigations was performed to improve the breeding capability which is essential for maintaining the fissile sustainability during reactor operation in thermal reactor such as Shippingport reactor and molten salt breeder reactor (MSBR) project. The preliminary study of breeding capability on water cooled thorium reactor has been investigated for various power output. The iterative calculation system is employed by coupling the equilibrium fuel cycle burn-up calculation and cell calculation of PIJ module of SRAC2000. In this calculation, 1238 fission products and 129 heavy nuclides are employed. In the cell calculation, 26 heavy metals and 66 fission products and 1 pseudo FP are employed. The employed nuclear data library was JENDL 3.2. The reactor is fueled by 2 33U-Th Oxide and it has used the light water coolant as moderator. Some characteristics such as conversion ratio and void reactivity coefficient performances are evaluated for the systems. The moderator to fuel ratio (MFR) values and average burnups are studied for survey parameter. The parametric survey for different power outputs are employed from 10 MWt to 3000 MWt for evaluating the some characteristics of core size and leakage effects to the spectra profile, required enrichment, breeding capability, fissile inventory condition, and void reactivity coefficient. Different power outputs are employed in order to evaluate its effect to the required enrichment for criticality, breeding capability, void reactivity and fissile inventory accumulation. The obtained value of the conversion ratios is evaluated by using the equilibrium atom composition. The conversion ratio is employed based on the

Heavy water leak detection using diffusion sampler

International Nuclear Information System (INIS)

Joshi, M.L.; Hussain, S.A.

1990-01-01

In the Pressurrised Heavy Water Reactors (PHWRs) detection of the sources of heavy water leaks is importent both for the purpose of radiation hazard control as well as for the reduction of escape/loss of heavy water which, is an expensive nuclear material. This paper describes an application of tritium diffusion sampler for heavy water leak detection. The diffusion sampler comprises an usual tritium counting glass vial with a special orifice. The counting vial has water vapour, deficient in HTO concentration. The HTO present outside diffuses in the vial through the orifice, gets exchanged with water of the wet filter paper kept at the bottom and the moisture in the vial atmosphere which has HTO concentration lower than that outside. This results in continuation of net movement of HTO in the vial. The exchanged tritium is counted in liquid scintillation spectrometer. The method has a sensitivity of 10000 dpm/DAC-h. (author). 2 figs., 2 ta bs

Radiation characteristics of spent fuel of heavy-water research reactor during long-term storage

International Nuclear Information System (INIS)

Gerasimov, A.S.; Kiselev, G.V.; Myrtsymova, L.A.; Zaritskaya, T.S.

2002-01-01

Decay heat power and radiotoxicity by water of actinides and fission products from spent fuel of heavy-water research reactor RA were calculated for period of storage during 300000 years. Three variants of fuel enrichment by 235 U were considered: 2%, 21%, and 80%. The mass of 235 U in one fuel element was supposed to be the same for all variants of enrichment. The decay heat power of fission products in initial period is about 20 times higher than that of actinides. Decay heat power and radiotoxicity of actinides do not practically decrease during long period of time as they are determined by nuclides with very long half-life periods. (author)

Removal of decay heat by specially designed isolation condensers for advanced heavy water reactors

Energy Technology Data Exchange (ETDEWEB)

Dhawan, M L; Bhatia, S K [Reactor Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

For Advanced Heavy Water Reactor (AHWR), removal of decay heat and containment heat is being considered by passive means. For this, special type of isolation condensers are designed. Isolation condensers when submerged in a pool of water, are the best choice because condensation of high temperature steam is an extremely efficient heat transfer mechanism. By the use of isolation condensers, not only heat is removed but also pressure and temperature of the system are automatically controlled without losing the coolant and without using conventional safety relief valves. In this paper, design optimisation studies of isolation condensers of different types with natural circulation for the removal of core decay heat for AHWR is presented. (author). 8 refs., 2 figs.

Study of the light emitted in the moderation of a heavy-water pile

International Nuclear Information System (INIS)

Breton, D.

1958-06-01

During the running of a reactor which uses water as a neutron moderator, a bluish light is seen to appear inside the liquid. A detailed study of this radiation, undertaken on the Fontenay-aux-Roses pile, has shown that the spectrum is identical with that which characterises the light produced by the Cerenkov effect. The light intensity as a function of the pile power grows exponentially as a function of time when the pile diverges, with a lifetime equal to that of the rise in power. An examination of the various particles present in the pile has led to the conclusion that only electrons with an energy greater than 260 keV con produce the Cerenkov light. The light source thus produced is about 2.10 6 photons/cm 2 of water, when the pile power equals 1 watt. (author) [fr

An investigation of differences between measured and calculated bucklings of a series of light water and heavy water moderated experimental cores

International Nuclear Information System (INIS)

Figgins, A.J.G.

1966-02-01

A series of light water and light and heavy water moderated exponential and critical experiments performed by the Babcock and Wilcox Company were analysed using the METHUSELAH programme and it was found that the calculated and measured critical bucklings differed significantly. The effect was most marked as the temperature of the moderator was raised in the light water cores where it amounted to 10 m -2 for a 200 deg. C rise above room temperature. Of this discrepancy 3 m -2 , at the most, could be explained as being caused by the experimental cores not being large enough to have a central asymptotic region, leaving an unexplained difference of 7 m -2 . It is suggested that the only region in which METHUSELAH could be usefully modified to improve this agreement is in the calculation of the resonance escape probability. The last section of the report compares the calculated and measured results obtained at room temperatures. (author)

Performance of water cooled nuclear power reactor fuels in India – Defects, failures and their mitigation

International Nuclear Information System (INIS)

Ganguly, Chaitanyamoy

2015-01-01

Water cooled and moderated nuclear power reactors account for more than 95% of the operating reactors in the world today. Light water reactors (LWRs) consisting of pressurized water reactor (PWR), their Russian counterpart namely VVER and boiling water reactor (BWR) will continue to dominate the nuclear power market. Pressurized heavy water reactor (PHWR), also known as CANDU, is the backbone of the nuclear power program in India. Updates on LWR and PHWR fuel performance are being periodically published by IAEA, OECD-NEA and the World Nuclear Association (WNA), highlighting fuel failure rate and the mitigation of fuel defects and failures. These reports clearly indicate that there has been significant improvement in in – pile fuel performance over the years and the present focus is to achieve zero fuel failure in high burn up and high performance fuels. The present paper summarizes the status of PHWR and LWR fuel performance in India, highlighting the manufacturing and the related quality control and inspection steps that are being followed at the PHWR fuel fabrication plant in order to achieve zero manufacturing defect which could contribute to achieving zero in – pile failure rate in operating and upcoming PHWR units in India. (author)

Safety analysis of RA reactor operation, I-II, Part I - RA reactor technical and operation characteristics; Analiza sigurnosti rada reaktora RA - I-III, I deo - Tehnicke i pogonske karakteristike reaktora RA

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

RA research reactor is a thermal, heavy water moderated system with graphite reflector having nominal power 6.5 MW. The 2% enriched metal uranium fuel in the reactor core produces mean thermal neutron flux of 2.9 10{sup 13} neutrons/cm{sup 2} s, and maximum neutron flux 5.5 10{sup 13} neutrons/cm{sup 2} s. main components of the reactor described in this report are: rector core, reflector, biological shield, heavy water cooling system, ordinary water cooling system, helium system, reactor control system, reactor safety system, dosimetry system, power supply system, and fuel transport system. Detailed reactor properties and engineering drawings of all the system are part of this volume.

Zero energy reactor RB technical characteristics and experimental possibilities

Energy Technology Data Exchange (ETDEWEB)

Jovanovic, S; Takac, S; Raisic, N; Lolic, B; Markovic, H [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1963-04-15

The zero energy reactor RB was constructed in 1958 in accordance with the nuclear reactor development programme of the Boris Kidric Institute of Nuclear Sciences. The reactor was in operation until the middle of 1959 when the heavy water, serving as the moderator, was transported to the high flux reactor RA, built at the same time at the Boris Kidric Institute. Owing to the fact that the purchase of new quantities of heavy water was planned for 1961 it was decided to reconstruct the RB reactor in order to improve the safety of the system and to obtain better flexibility in performing the experiments. New control, safety and radiation monitoring systems were constructed. Some changes were also made on the reactor tank, water circulation system and the water level monitoring equipment. The reconstruction was completed in 1961. and the heavy water was delivered early in 1962. The reconstructed reactor was critical for the first time in summer 1962, and from that time was in continuous operation. This report presents an outline of the design and construction characteristics of the reactor. The main intention is to inform potential users of the reactor about experimental possibilities, advantages and disadvantages of such a critical facility.

Zero energy reactor RB technical characteristics and experimental possibilities

International Nuclear Information System (INIS)

Jovanovic, S.; Takac, S.; Raisic, N.; Lolic, B.; Markovic, H.

1963-04-01

The zero energy reactor RB was constructed in 1958 in accordance with the nuclear reactor development programme of the Boris Kidric Institute of Nuclear Sciences. The reactor was in operation until the middle of 1959 when the heavy water, serving as the moderator, was transported to the high flux reactor RA, built at the same time at the Boris Kidric Institute. Owing to the fact that the purchase of new quantities of heavy water was planned for 1961 it was decided to reconstruct the RB reactor in order to improve the safety of the system and to obtain better flexibility in performing the experiments. New control, safety and radiation monitoring systems were constructed. Some changes were also made on the reactor tank, water circulation system and the water level monitoring equipment. The reconstruction was completed in 1961. and the heavy water was delivered early in 1962. The reconstructed reactor was critical for the first time in summer 1962, and from that time was in continuous operation. This report presents an outline of the design and construction characteristics of the reactor. The main intention is to inform potential users of the reactor about experimental possibilities, advantages and disadvantages of such a critical facility

Reactor core of light water-cooled reactor

International Nuclear Information System (INIS)

Miwa, Jun-ichi; Aoyama, Motoo; Mochida, Takaaki.

1996-01-01

In a reactor core of a light water cooled reactor, the center of the fuel rods or moderating rods situated at the outermost circumference among control rods or moderating rods are connected to divide a lattice region into an inner fuel region and an outer moderator region. In this case, the area ratio of the moderating region to the fuel region is determined to greater than 0.81 for every cross section of the fuel region. The moderating region at the outer side is increased relative to the fuel rod region at the inner side while keeping the lattice pitch of the fuel assembly constant, thereby suppressing the increase of an absolute value of a void reactivity coefficient which tends to be caused when using MOX fuels as a fuel material, by utilizing neutron moderation due to a large quantity of coolants at the outer side of the fuel region. The void reactivity coefficient can be made substantially equal with that of uranium fuel assembly without greatly reducing a plutonium loading amount or without greatly increasing linear power density. (N.H.)

A study of Cirus heavy water system isotopic purity

International Nuclear Information System (INIS)

Thomas, Shibu; Sahu, A.K.; Unni, V.K.P.; Pant, R.C.

2000-01-01

Cirus uses heavy water as moderator and helium as cover gas. Approximately one tonne of heavy water was added to the system every year for routine make up. Isotopic purity (IP) of this water used for addition was always higher than that of the system. Though this should increase IP of heavy water in the system, it has remained almost at the same level, over the years. A study was carried out to estimate the extent of improvement in IP of heavy water in the system that should have occurred because of this and other factors in last 30 years. Reasons for non-occurrence of such an improvement were explored. Ion exchange resins used for purification of heavy water and air ingress into helium cover gas system appear to be the principal sources of entry of light water into heavy water system. (author)

Reactor core and passive safety systems descriptions of a next generation pressure tube reactor - mechanical aspects

Energy Technology Data Exchange (ETDEWEB)

Yetisir, M.; Gaudet, M.; Rhodes, D.; Hamilton, H.; Pencer, J. [Atomic Energy of Canada Limited, Chalk River, ON (Canada)

2014-07-01

Canada has been developing a channel-type supercritical water-cooled nuclear reactor concept, often called the Canadian SCWR. The objective of this reactor concept is to meet the technology goals of the Generation IV International Forum (GIF) for the next generation nuclear reactor development, which include enhanced safety features (inherent safe operation and deploying passive safety features), improved resource utilization, sustainable fuel cycle, and greater proliferation resistance than Generation III nuclear reactors. The Canadian SCWR core concept consists of a high-pressure inlet plenum, a separate low-pressure heavy water moderator contained in a calandria vessel, and 336 pressure tubes surrounded by the moderator. The reactor uses supercritical water as a coolant, and a direct steam power cycle to generate electricity. The reactor concept incorporates advanced safety features such as passive core cooling, long-term decay heat rejection to the environment and fuel melt prevention via passive moderator cooling. These features significantly reduce core damage frequency relative to existing nuclear reactors. This paper presents a description of the design concepts for the Canadian SCWR core, reactor building layout and the plant layout. Passive safety concepts are also described that address containment and core cooling following a loss-of coolant accident, as well as long term reactor heat removal at station blackout conditions. (author)

Natural uranium fueled light water moderated breeding hybrid power reactors: a feasibility study

International Nuclear Information System (INIS)

Greenspan, E.; Schneider, A.; Misolovin, A.; Gilai, D.; Levin, P.

1978-06-01

The first part of the study consists of a thorough investigation of the properties of subcritical thermal lattices for hybrid reactor applications. Light water is found to be the best moderator for (fuel-self-sufficient) FSS hybrid reactors for power generation. Several lattice geometries and compositions of particular promise for LWHRs are identified. Using one of these lattices, fueled with natural uranium, the performance of several concepts of LWHR blankets is investigated, and optimal blanket designs are identified. The effect of blanket coverage efficiency and the feasibility of separating the functions of tritium breeding and of power generation to different blankets are investigated. Optimal iron-water shields for LWHRs are also determined. The performance of generic types of LWHRs is evaluated. The evolution of the blanket properties with burnup is evaluated and fuel management schemes are briefly examined. The feasibility of using the lithium system of the blanket to control the blanket power amplitude and shape is also investigated. A parametric study of the energy balance of LWHR power plants is carried out, and performance parameters expected from LWHRs are estimated. Discussions are given of special features of LWHRs and their fuel cycle

Thermophysical properties of materials for water cooled reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-06-01

The IAEA Co-ordinated Research Programme (CRP) to establish a thermophysical properties data base for light and heavy water reactor materials was organized within the framework of the IAEA`s International Working Group on Advanced Technologies for Water Cooled Reactors. The work within the CRP started in 1990. The objective of the CRP was to collect and systemaize a thermophysical properties data base for light and heavy water reactor materials under normal operating, transient and accident conditions. The important thermophysical properties include thermal conductivity, thermal diffusivity, specific heat capacity, enthalpy, thermal expansion and others. These properties as well as the oxidation of zirconium-based alloys, the thermophysical characteristics of high temperature concrete-core melt interaction and the mechanical properties of construction materials are presented in this report. It is hoped that this report will serve as a useful source of thermophysical properties data for water cooled reactor analyses. The properties data are maintained on the THERSYST system at the University of Stuttgart, Germany and are internationally available. Refs, figs, tabs.

Thermophysical properties of materials for water cooled reactors

International Nuclear Information System (INIS)

1997-06-01

The IAEA Co-ordinated Research Programme (CRP) to establish a thermophysical properties data base for light and heavy water reactor materials was organized within the framework of the IAEA's International Working Group on Advanced Technologies for Water Cooled Reactors. The work within the CRP started in 1990. The objective of the CRP was to collect and systemaize a thermophysical properties data base for light and heavy water reactor materials under normal operating, transient and accident conditions. The important thermophysical properties include thermal conductivity, thermal diffusivity, specific heat capacity, enthalpy, thermal expansion and others. These properties as well as the oxidation of zirconium-based alloys, the thermophysical characteristics of high temperature concrete-core melt interaction and the mechanical properties of construction materials are presented in this report. It is hoped that this report will serve as a useful source of thermophysical properties data for water cooled reactor analyses. The properties data are maintained on the THERSYST system at the University of Stuttgart, Germany and are internationally available. Refs, figs, tabs

Construction management of Indian pressurized heavy water reactors

International Nuclear Information System (INIS)

Bohra, S.A.; Sharma, P.D.

2006-01-01

Pandit Jawaharlal Nehru and Dr. Homi J. Bhabha, the visionary architects of Science and Technology of modern India foresaw the imperative need to establish a firm base for indigenous research and development in the field of nuclear electricity generation. The initial phase has primarily focused on the technology development in a systematic and structured manner, which has resulted in establishment of strong engineering, manufacturing and construction base. The nuclear power program started with the setting up of two units of boiling light water type reactors in 1969 for speedy establishment of nuclear technology, safety culture, and development of operation and maintenance manpower. The main aim at that stage was to demonstrate (to ourselves, and indeed to the rest of the world) that India, inspite of being a developing country, with limited industrial infrastructure and low capacity power grids, could successfully assimilate the high technology involved in the safe and economical operation of nuclear power reactors. The selection of a BWR was in contrast to the pressurized heavy water reactors (PHWR), which was identified as the flagship for the first stage of India's nuclear power program. The long-term program in three stages utilizes large reserves of thorium in the monazite sands of Kerala beaches in the third stage with first stage comprising of series of PHWR type plants with a base of 10,000 MW. India has at present 14 reactors in operation 12 of these being of PHWR type. The performance of operating units of 2720 MW has improved significantly with an overall capacity factor of about 90% in recent times. The construction work on eight reactor units with installed capacity of 3960 MW (two PHWRs of 540 MW each, four PHWRs of 220 MW each and two VVERs of 1000 MW each) is proceeding on a rapid pace with project schedules of less than 5 years from first pour of concrete. This is being achieved through advanced construction technology and management. Present

Pressure loadings of Soviet-designed VVER [Water-Cooled, Water-Moderated Energy Reactor] reactor release mitigation structures from large-break LOCAs

International Nuclear Information System (INIS)

Sienicki, J.J.; Horak, W.C.

1989-01-01

Analyses have been carried out of the pressurization of the accident release mitigation structures of Soviet-designed VVER (Water-Cooled, Water-Moderated Energy Reactor) pressurized water reactors following large-break loss-of-coolant accidents. Specific VVER systems for which calculations were performed are the VVER-440 model V230, VVER-440 model V213, and VVER-1000 model V320. Descriptions of the designs of these and other VVER models are contained in the report DOE/NE-0084. The principal objective of the current analyses is to calculate the time dependent pressure loadings inside the accident localization or containment structures immediately following the double-ended guillotine rupture of a primary coolant pipe. In addition, the pressures are compared with the results of calculations of the response of the structures to overpressure. Primary coolant system thermal hydraulic conditions and the fluid conditions at the break location were calculated with the RETRAN-02 Mod2 computer code (Agee, 1984). Pressures and temperatures inside the building accident release mitigation structures were obtained from the PACER (Pressurization Accompanying Coolant Escape from Ruptures) multicompartment containment analysis code developed at Argonne National Laboratory. The analyses were carried out using best estimate models and conditions rather than conservative, bounding-type assumptions. In particular, condensation upon structure and equipment was calculated using correlations based upon analyses of the HDR, Marviken, and Battelle Frankfurt containment loading experiments. The intercompartment flow rates incorporate an effective discharge coefficient and liquid droplet carryover fraction given by expressions of Schwan determined from analyses of the Battelle Frankfurt and Marviken tests. 5 refs., 4 figs

Power level effects on thorium-based fuels in pressure-tube heavy water reactors

Energy Technology Data Exchange (ETDEWEB)

Bromley, B.P.; Edwards, G.W.R., E-mail: blair.bromley@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Sambavalingam, P. [Univ. of Ontario Inst. of Technology, Oshawa, Ontario (Canada)

2016-06-15

Lattice and core physics modeling and calculations have been performed to quantify the impact of power/flux levels on the reactivity and achievable burnup for 35-element fuel bundles made with Pu/Th or U-233/Th. The fissile content in these bundles has been adjusted to produce on the order of 20 MWd/kg burnup in homogeneous cores in a 700 MWe-class pressure-tube heavy water reactor, operating on a once-through thorium cycle. Results demonstrate that the impact of the power/flux level is modest for Pu/Th fuels but significant for U-233/Th fuels. In particular, high power/flux reduces the breeding and burnup potential of U-233/Th fuels. Thus, there may be an incentive to operate reactors with U-233/Th fuels at a lower power density or to develop alternative refueling schemes that will lower the time-average specific power, thereby increasing burnup.(author)

Power level effects on thorium-based fuels in pressure-tube heavy water reactors

International Nuclear Information System (INIS)

Bromley, B.P.; Edwards, G.W.R.; Sambavalingam, P.

2016-01-01

Lattice and core physics modeling and calculations have been performed to quantify the impact of power/flux levels on the reactivity and achievable burnup for 35-element fuel bundles made with Pu/Th or U-233/Th. The fissile content in these bundles has been adjusted to produce on the order of 20 MWd/kg burnup in homogeneous cores in a 700 MWe-class pressure-tube heavy water reactor, operating on a once-through thorium cycle. Results demonstrate that the impact of the power/flux level is modest for Pu/Th fuels but significant for U-233/Th fuels. In particular, high power/flux reduces the breeding and burnup potential of U-233/Th fuels. Thus, there may be an incentive to operate reactors with U-233/Th fuels at a lower power density or to develop alternative refueling schemes that will lower the time-average specific power, thereby increasing burnup.(author)

Benchmarking severe accident computer codes for heavy water reactor applications

Energy Technology Data Exchange (ETDEWEB)

Choi, J.H. [International Atomic Energy Agency, Vienna (Austria)

2010-07-01

Consideration of severe accidents at a nuclear power plant (NPP) is an essential component of the defence in depth approach used in nuclear safety. Severe accident analysis involves very complex physical phenomena that occur sequentially during various stages of accident progression. Computer codes are essential tools for understanding how the reactor and its containment might respond under severe accident conditions. International cooperative research programmes are established by the IAEA in areas that are of common interest to a number of Member States. These co-operative efforts are carried out through coordinated research projects (CRPs), typically 3 to 6 years in duration, and often involving experimental activities. Such CRPs allow a sharing of efforts on an international basis, foster team-building and benefit from the experience and expertise of researchers from all participating institutes. The IAEA is organizing a CRP on benchmarking severe accident computer codes for heavy water reactor (HWR) applications. The CRP scope includes defining the severe accident sequence and conducting benchmark analyses for HWRs, evaluating the capabilities of existing computer codes to predict important severe accident phenomena, and suggesting necessary code improvements and/or new experiments to reduce uncertainties. The CRP has been planned on the advice and with the support of the IAEA Nuclear Energy Department's Technical Working Groups on Advanced Technologies for HWRs. (author)

Research and development on reduced-moderation light water reactor with passive safety features (Contract research)

International Nuclear Information System (INIS)

Iwamura, Takamichi; Okubo, Tsutomu; Akie, Hiroshi; Kugo, Teruhiko; Yonomoto, Taisuke; Kureta, Masatoshi; Ishikawa, Nobuyuki; Nagaya, Yasunobu; Araya, Fumimasa; Okajima, Shigeaki; Okumura, Keisuke; Suzuki, Motoe; Mineo, Hideaki; Nakatsuka, Toru

2004-06-01

The present report contains the achievement of 'Research and Development on Reduced-moderation Light Water Reactor with Passive Safety Features', which was performed by Japan Atomic Energy Research Institute (JAERI), Hitachi Ltd., Japan Atomic Power Company and Tokyo Institute of Technology in FY2000-2002 as the innovative and viable nuclear energy technology (IVNET) development project operated by the Institute of Applied Energy (IAE). In the present project, the reduced-moderation water reactor (RMWR) has been developed to ensure sustainable energy supply and to solve the recent problems of nuclear power and nuclear fuel cycle, such as economical competitiveness, effective use of plutonium and reduction of spent fuel storage. The RMWR can attain the favorable characteristics such as high burnup, long operation cycle, multiple recycling of plutonium (Pu) and effective utilization of uranium resources based on accumulated LWR technologies. Our development target is 'Reduced-moderation Light Water Reactor with Passive Safety Features' with innovative technologies to achieve above mentioned requirement. Electric power is selected as 300 MWe considering anticipated size required for future deployment. The reactor core consists of MOX fuel assemblies with tight lattice arrangement to increase the conversion ratio. Design targets of the core specification are conversion ratio more than unity, negative void reactivity feedback coefficient to assure safety, discharged burnup more than 60 GWd/t and operation cycle more than 2 years. As for the reactor system, a small size natural circulation BWR with passive safety systems is adopted to increase safety and reduce construction cost. The results obtained are as follows: As regards core design study, core design was performed to meet the goal. Sequence of startup operation was constructed for the RMWR. As the plant design, plant system was designed to achieve enhanced economy using passive safety system effectively. In

Preliminary definition of the design of a nuclear reactor for research and radioisotope production using natural uranium and heavy water

International Nuclear Information System (INIS)

Llagostera Beltran, J.I.

1982-01-01

A study was conducted about the evolution of the Brazilian importations of radioisotopes, from the beginning of the 70's since they have been increasingly used in the Country. In view of the limited production capacity of radioactive isotopes now existing in Brazil, a nuclear reactor type (natural uranium and heavy water) was defined, for research and production of radioisotopes, wich, besides providing, at least partially, the Brazilian needs of said isotopes, permits a large national participation in its project, construction and operating maintenance. The processes for heavy water production have been analyzed and it could be detected what is the best alternative for the production thereof, in low scale, in Brazil. The options concerning the definition of the main components of the reactor were justified and its most important features were determined, in relation to the neutronic and thermal aspects, being so defined its most significant parameters. The annual quantities were estimated, in terms of total and specific activity, for the radioisotopes that could be obtained by means of the proposed reactor, which, by now, are participating, to a large extent, in the total of Brazilian importation of radioactive isotopes. (Author) [pt

MCCI study for Pressurized Heavy Water Reactor under hypothetical accident condition

International Nuclear Information System (INIS)

Verma, Vishnu; Mukhopadhyay, Deb; Chatterjee, B.; Singh, R.K.; Vaze, K.K.

2011-01-01

In case of severe core damage accident in Pressurized Heavy Water Reactor (PHWR), large amount of molten corium is expected to come out into the calandria vault due to failure of calandria vessel. Molten corium at high temperature is sufficient to decompose and ablate concrete. Such attack could fail CV by basement penetration. Since containment is ultimate barrier for activity release. The Molten Core Concrete Interaction (MCCI) of the resulting pool of debris with the concrete has been identified as an important part of the accident sequence. MCCI Analysis has been carried out for PHWR for a hypothetical accident condition where total core material is considered to be relocated in calandria vault. Concrete ablation rate in vertical and radial direction is evaluated for rectangular geometry using MEDICIS module of ASTEC Code. Amount of gases released during MCCI is also evaluated. (author)

Application of Genetic Algorithm methodologies in fuel bundle burnup optimization of Pressurized Heavy Water Reactor

International Nuclear Information System (INIS)

Jayalal, M.L.; Ramachandran, Suja; Rathakrishnan, S.; Satya Murty, S.A.V.; Sai Baba, M.

2015-01-01

Highlights: • We study and compare Genetic Algorithms (GA) in the fuel bundle burnup optimization of an Indian Pressurized Heavy Water Reactor (PHWR) of 220 MWe. • Two Genetic Algorithm methodologies namely, Penalty Functions based GA and Multi Objective GA are considered. • For the selected problem, Multi Objective GA performs better than Penalty Functions based GA. • In the present study, Multi Objective GA outperforms Penalty Functions based GA in convergence speed and better diversity in solutions. - Abstract: The work carried out as a part of application and comparison of GA techniques in nuclear reactor environment is presented in the study. The nuclear fuel management optimization problem selected for the study aims at arriving appropriate reference discharge burnup values for the two burnup zones of 220 MWe Pressurized Heavy Water Reactor (PHWR) core. Two Genetic Algorithm methodologies namely, Penalty Functions based GA and Multi Objective GA are applied in this study. The study reveals, for the selected problem of PHWR fuel bundle burnup optimization, Multi Objective GA is more suitable than Penalty Functions based GA in the two aspects considered: by way of producing diverse feasible solutions and the convergence speed being better, i.e. it is capable of generating more number of feasible solutions, from earlier generations. It is observed that for the selected problem, the Multi Objective GA is 25.0% faster than Penalty Functions based GA with respect to CPU time, for generating 80% of the population with feasible solutions. When average computational time of fixed generations are considered, Penalty Functions based GA is 44.5% faster than Multi Objective GA. In the overall performance, the convergence speed of Multi Objective GA surpasses the computational time advantage of Penalty Functions based GA. The ability of Multi Objective GA in producing more diverse feasible solutions is a desired feature of the problem selected, that helps the

Condensation nuclear power plants with water-cooled graphite-moderated channel type reactors and advances in their development

International Nuclear Information System (INIS)

Boldyrev, V.M.; Mikhaj, V.I.

1985-01-01

Consideration is being given to results of technical and economical investigations of advisability of increasing unit power by elevating steam generating capacity as a result of inserting numerous of stereotype sectional structural elements of the reactor with similar thermodynamic parameters. It is concluded that construction of power units of condensation nuclear power plants with water-cooled graphite-moderated channel type reactors of 2400-3200 MWe and higher unit power capacity represents the real method for sharp growth of efficiency and labour productivity in power industry. It can also provide the required increase of the rate of putting electrogenerating powers into operation

Sources of variability for the single-comparator method in a heavy-water reactor

International Nuclear Information System (INIS)

Damsgaard, E.; Heydorn, K.

1978-11-01

The well thermalized flux in the heavy-water-moderated DR 3 reactor at Risoe prompted us to investigate to what extent a single comparator could be used for multi-element determination instead of multiple comparators. The reliability of the single-comparator method is limited by the thermal-to-epithermal ratio, and experiments were designed to determine the variations in this ratio throughout a reactor operating period (4 weeks including a shut-down period of 4-5 days). The bi-isotopic method using zirconium as monitor was chosen, because 94 Zr and 96 Zr exhibit a large difference in their Isub(o)/Σsub(th) values, and would permit determination of the flux ratio with a precision sufficient to determine variations. One of the irradiation facilities comprises a rotating magazine with 3 channels, each of which can hold five aluminium cans. In this rig, five cans, each holding a polyvial with 1 ml of aqueous zirconium solution were irradiated simultaneously in one channel. Irradiations were carried out in the first and the third week of 4 periods. In another facility consisting of a pneumatic tube system, two samples were simultaneously irradiated on top of each other in a polyethylene rabbit. Experiments were carried out once a week for 4 periods. All samples were counted on a Ge(Li)-detector for 95 Zr, 97 sup(m)Nb and 97 Nb. The thermal-to-epithermal flux ratio was calculated from the induced activity, the nuclear data for the two zirconium isotopes and the detector efficiency. By analysis of variance the total variation of the flux ratio was separated into a random variation between reactor periods, and systematic differences between the positions, as well as the weeks in the operating period. If the variations are in statistical control, the error resulting from use of the single-comparator method in multi-element determination can be estimated for any combination of irradiation position and day in the operating period. With the measure flux ratio variations in DR

CFD simulations of moderator flow inside Calandria of the Passive Moderator Cooling System of an advanced reactor

Energy Technology Data Exchange (ETDEWEB)

Pal, Eshita [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400 094 (India); Kumar, Mukesh [Reactor Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India); Joshi, Jyeshtharaj B., E-mail: jbjoshi@gmail.com [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400 094 (India); Department of Chemical Engineering, Institute of Chemical Technology, Matunga, Mumbai 400019 India (India); Nayak, Arun K. [Reactor Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India); Vijayan, Pallippattu K., E-mail: vijayanp@barc.gov.in [Reactor Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai 400 085 (India)

2015-10-15

Highlights: • CFD simulations in the Calandria of an advanced reactor under natural circulation. • Under natural convection, majority of the flow recirculates within the Calandria. • Maximum temperature is located at the top and center of the fuel channel matrix. • During SBO, temperature inside Calandria is stratified. - Abstract: Passive systems are being examined for the future Advanced Nuclear Reactor designs. One of such concepts is the Passive Moderator Cooling System (PMCS), which is designed to remove heat from the moderator in the Calandria vessel passively in case of an extended Station Black Out condition. The heated heavy-water moderator (due to heat transferred from the Main Heat Transport System (MHTS) and thermalization of neutrons and gamma from radioactive decay of fuel) rises upward due to buoyancy, gets cooled down in a heat exchanger and returns back to Calandria, completing a natural circulation loop. The natural circulation should provide sufficient cooling to prevent the increase of moderator temperature and pressure beyond safe limits. In an earlier study, a full-scale 1D transient simulation was performed for the reactor including the MHTS and the PMCS, in the event of a station blackout scenario (Kumar et al., 2013). The results indicate that the systems remain within the safe limits for 7 days. However, the flow inside a geometry like Calandria is quite complex due to its large size and inner complexities of dense fuel channel matrix, which was simplified as a 1D pipe flow in the aforesaid analysis. In the current work, CFD simulations are performed to study the temperature distributions and flow distribution of moderator inside the Calandria vessel using a three-dimensional CFD code, OpenFoam 2.2.0. First, a set of steady state simulation was carried out for a band of inlet mass flow rates, which gives the minimum mass flow rate required for removing the maximum heat load, by virtue of prediction of hot spots inside the Calandria

Determination of the tritium content in the reactor heavy water, Phase II; Odredjivanje porasta kolicine tritijuma u reaktorskoj teskoj vodi, II faza

Energy Technology Data Exchange (ETDEWEB)

Ribnikar, S [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-07-15

Measurement results of the {sup 3}H activity in non-irradiated water and after reactor operation are presented. Methods were developed for sampling and radiochemical water purification by ion exchange and multiple distillation. Methods for absolute measurement of soft beta radiation of tritium were established. Migration of tritium through the heavy water RA reactor system was monitored. Results were compared with other measured reactor parameters. Prikazani su rezultati merenja aktivnosti {sup 3}H u nezracenoj vodi i posle rada reaktora; razradjeni su metodi za uzimanje i radiohemijsko preciscavanje vode putem jonske izmene i visestepene destilacije; postavljeni metodi za apsolutno merenje mekog beta-zracenja tritijuma; pracene su migracije tritijuma kroz teskovodni sistem reaktora; takodje su interpretirani i poredjeni rezultati sa drugim merenim parametrima reaktora.

Startup of a high-temperature reactor cooled and moderated by supercritical-pressure light water

International Nuclear Information System (INIS)

Yi, Tin Tin; Ishiwatari, Yuki; Koshizuka, Seiichi; Oka, Yoshiaki

2003-01-01

The startup schemes of high-temperature reactors cooled and moderated by supercritical pressure light water (SCLWR-H) with square lattice and descending flow type water rods are studied by thermal-hydraulic analysis. In this study, two kinds of startup systems are investigated. In the constant pressure startup system, the reactor starts at a supercritical pressure. A flash tank and pressure reducing valves are necessary. The flash tank is designed so that the moisture content in the steam is less than 0.1%. In sliding pressure startup system, the reactor starts at a subcritical pressure. A steam-water separator and a drain tank are required for two-phase flow at startup. The separator is designed by referring to the water separator used in supercritical fossil-fired power plants. The maximum cladding surface temperature during the power-raising phase of startup is restricted not to exceed the rated value of 620degC. The minimum feedwater flow rate is 25% for constant pressure startup and 35% for sliding pressure startup system. It is found that both constant pressure startup system and sliding pressure startup system are feasible in SCLWR-H from the thermal hydraulic point of view. The core outlet temperature as high as 500degC can be achieved in the present design of SCLWR-H. Since the feedwater flow rate of SCLWR-H (1190 kg/s) is lower than that of the previous SCR designs the weight of the component required for startup is reduced. The sliding pressure startup system is better than constant pressure startup system in order to reduce the required component weight (and hence material expenditure) and to simplify the startup plant system. (author)

Plant life management processes and practices for heavy water reactors

International Nuclear Information System (INIS)

Kang, K.-S.; Cleveland, J.; Clark, C.R.

2006-01-01

In general, heavy water reactor (HWR) nuclear power plant (NPP) owners would like to keep their NPPs in service as long as they can be operated safely and economically. Their decisions are depending on essentially business model. They involve the consideration of a number of factors, such as the material condition of the plant, comparison with current safety standards, the socio-political climate and asset management/ business planning considerations. Continued plant operation, including operation beyond design life, called 'long term operation, depends, among other things, on the material condition of the plant. This is influenced significantly by the effectiveness of ageing management. Key attributes of an effective plant life management program include a focus on important systems, structure and components (SSCs) which are susceptible to ageing degradation, a balance of proactive and reactive ageing management programmes, and a team approach that ensures the co-ordination of and communication between all relevant nuclear power plant and external programmes. Most HWR NPP owners/operators use a mix of maintenance, surveillance and inspection (MSI) programs as the primary means of managing ageing. Often these programs are experienced-based and/or time-based and may not be optimised for detecting and/or managing ageing effects. From time-to-time, operational history has shown that this practice can be too reactive, as it leads to dealing with ageing effects (degradation of SSCs) after they have been detected. In many cases premature and/or undetected ageing cannot be traced back to one specific reason or an explicit error. The root cause is often a lack of communication, documentation and/or co-ordination between design, commissioning, operation or maintenance organizations. This lack of effective communication and interfacing frequently arises because, with the exception of major SSCs, such as the fuel channels or steam generators, there is a lack of explicit

Super critical water reactors

International Nuclear Information System (INIS)

Dumaz, P.; Antoni, O; Arnoux, P.; Bergeron, A; Renault, C.; Rimpault, G.

2005-01-01

Water is used as a calori-porter and moderator in the most major nuclear centers which are actually in function. In the pressurized water reactor (PWR) and boiling water reactor (BWR), water is maintained under critical point of water (21 bar, 374 Centigrade) which limits the efficiency of thermodynamic cycle of energy conversion (yield gain of about 33%) Crossing the critical point, one can then use s upercritical water , the obtained pressure and temperature allow a significant yield gains. In addition, the supercritical water offers important properties. Particularly there is no more possible coexistence between vapor and liquid. Therefore, we don't have more boiling problem, one of the phenomena which limits the specific power of PWR and BWR. Since 1950s, the reactor of supercritical water was the subject of studies more or less detailed but neglected. From the early 1990s, this type of conception benefits of some additional interests. Therefore, in the international term G eneration IV , the supercritical water reactors had been considered as one of the big options for study as Generation IV reactors. In the CEA, an active city has engaged from 1930 with the participation to a European program: The HPWR (High Performance Light Water Reactor). In this contest, the R and D studies are focused on the fields of neutrons, thermodynamic and materials. The CEA intends to pursue a limited effort of R and D in this field, in the framework of international cooperation, preferring the study of versions of rapid spectrum. (author)

Subchannel analysis of 37-rod tight-lattice bundle experiments for reduced-moderation water reactor

International Nuclear Information System (INIS)

Nakatsuka, Toru; Tamai, Hidesada; Akimoto, Hajime

2005-01-01

R and D project to investigate thermal-hydraulic performance of tight-lattice fuel bundles for Reduced-Moderation Water Reactor (RMWR) started at Japan Atomic Energy Research Institute (JAERI) in collaboration with utilities, reactor vendors and universities from 2002. The RMWR realizes a high conversion ratio larger than 0.1 for sustainable energy supply through plutonium multiple recycling based on the well-experienced LWR technologies. The reactor core comprises tight-lattice fuel assemblies with gap clearance of around 1.0 mm to reduce the water volume ratio to achieve the high conversion ratio. A problem of utmost importance from a thermal-hydraulic point of view is the coolability of the tight-lattice assembly with such a small gap width. JAERI has been carrying out experimental study to investigate the system parameter effects on the thermal-hydraulic performance and to confirm the feasibility of the core. In the present study, the subchannel analysis code NASCA was applied to 37-rod tight-lattice bundle experiments. The NASCA can give good predictions of critical power for the gap width of 1.3 mm while the prediction accuracy decreases for the gap width of 1.0 mm. To improve the prediction accuracy, the code will be modified to take the effect of film thickness distribution around fuel rods on boiling transition. (author)

Fuel Management Study for a CANDU reactor Using New Physics Codes Suite

International Nuclear Information System (INIS)

Kim, Won Young; Kim, Bong Ghi; Park, Joo Hwan

2008-01-01

A CANDU reactor is a heavy-water-moderated, natural uranium fuelled reactor with a pressure tube. The reactor contains a horizontal cylindrical vessel (calandria) and each pressure tube is isolated from the heavy-water moderator in a calandria. This allows the moderator system to be operated of a high-pressure and of a high-temperature coolant in pressure tube. The primary reactivity control in a CANDU reactor is the on-power refueling on a daily basis and an additional reactivity control is provided through an individual reactivity device movement, which includes 21 adjusters, 6 liquid zone controllers, 4 mechanical control absorbers and 2 shutdown systems. The refueling in CANDU is carried out on power and this makes the in-core fuel management different from that in a reactor refueled during shutdowns. The objective of a fuel management is to determine a fuel loading and fuel replacement procedure which will result in a minimum total unit energy cost in a safe and reliable operation. In this article, the in-core fuel management for the CANDU reactor was studied by using the new physics code suite of WIMS-IST/DRAGON-IST/RFSP-IST with the model of Wolsong-1 NPP

Study on neutronics performance of flower shape advanced supercritical water cooled fast reactor with different solid moderators