WorldWideScience

Sample records for heavy element research

  1. Heavy element research

    Anon.

    1976-01-01

    Heavy element research activities in metallurgy and ceramics during 1976 at Lawrence Berkeley Laboratory are reviewed. Topics include: microstructure, properties and alloy design; ceramic alloy program; high resolution and high voltage electron microscopy; and powder metallurgy

  2. Heavy-element research

    Anon.

    1975-01-01

    The status is reported of studies on the solid-state chemistry of the actinides and lanthanides, spectroscopy of actinide compounds, and dynamic chemical description of actinide elements in solution. Phase studies were done on Rb 2 UO 4 , K 2 UO 4 , Li 2 UO 4 , and Es 2 U 2 O 7 . The lithium neptunate (VI) system was investigated and the existence of Li 2 NpO 4 was established. In oxidation-reduction studies it was shown that Am(III) can be electrolytically oxidized to Am(IV) in strong H 3 PO 4 , but Cf(III) and Pr(III) do not oxidize. The low-temperature absorption spectrum of thin films of NpBr 3 was investigated. (U.S.)

  3. Recent research on the heavy transuranium elements

    Seaborg, G.T.

    1988-09-01

    This review is devoted to recent research (performed in the 1980s) on the heavy members of the group, defined as the transcurium elements (with a few references to related work on lighter elements). It covers the discovery of the three heaviest elements, the discovery of new isotopes, investigation of interesting decay properties of some previously known isotopes, investigations of some heavy ion reaction mechanisms in this region, and recent investigations of nuclear and chemical properties. It is not exhaustive in its coverage, is necessarily succinct, and inevitably places emphasis on those aspects with which the author is most familiar. 92 refs., 3 figs

  4. Automated rapid chemistry in heavy element research

    Schaedel, M.

    1994-01-01

    With the increasingly short half-lives of the heavy element isotopes in the transition region from the heaviest actinides to the transactinide elements the demand for automated rapid chemistry techniques is also increasing. Separation times of significantly less than one minute, high chemical yields, high repetition rates, and an adequate detection system are prerequisites for many successful experiments in this field. The development of techniques for separations in the gas phase and in the aqueous phase for applications of chemical or nuclear studies of the heaviest elements are briefly outlined. Typical examples of results obtained with automated techniques are presented for studies up to element 105, especially those obtained with the Automated Rapid Chemistry Apparatus, ARCA. The prospects to investigate the properties of even heavier elements with chemical techniques are discussed

  5. Status on the heavy elements research using the DV-DFS method

    Hirata, Masaru; Bastug, T.; Sekine, Rika; Onoe, Jun; Nakamatsu, Hirohide; Mukoyama, Takeshi

    1999-03-01

    In this review report, we describe recent progress on the heavy elements research using the discrete-variational Dirac-Fock-Slater (DV-DFS) method which is being improved by Kyoto University, Shizuoka University, RIKEN and JAERI. The DV-DFS is a versatile method for interpreting spectroscopic data and predicting chemical bonding of polyatomic systems including heavy elements. This review is based on the lectures given in 74th spring meeting of chemical Society of Japan (March, 1998) and also at the workshop on the XAFS-relativistic electronic structure calculation for the actinides research which was held at Tokai Research Establishment of JAERI (November, 1998). (author)

  6. Nuclear physics and heavy element research at LLNL

    Stoyer, M A; Ahle, L E; Becker, J A; Bernstein, L A; Bleuel, D L; Burke, J T; Dashdorj, D; Henderson, R A; Hurst, A M; Kenneally, J M; Lesher, S R; Moody, K J; Nelson, S L; Norman, E B; Pedretti, M; Scielzo, N D; Shaughnessy, D A; Sheets, S A; Stoeffl, W; Stoyer, N J; Wiedeking, M; Wilk, P A; Wu, C Y

    2009-05-11

    This paper highlights some of the current basic nuclear physics research at Lawrence Livermore National Laboratory (LLNL). The work at LLNL concentrates on investigating nuclei at the extremes. The Experimental Nuclear Physics Group performs research to improve our understanding of nuclei, nuclear reactions, nuclear decay processes and nuclear astrophysics; an expertise utilized for important laboratory national security programs and for world-class peer-reviewed basic research.

  7. Present status of research activities conducted by research group for heavy elements microbiology in JAERI

    Ohnuki, Toshihiko; Ozaki, Takuo; Yoshida, Takahiro

    2004-01-01

    It has been recognized that microbial transformations of radionuclides and toxic metals could be significant in the environment, but there is a paucity of information on the mechanisms of biotransformation of radionuclides by the microorganisms. An understanding at the fundamental level the mechanisms of mobilization, immobilization and bioavailability of radioactive elements in particular the actinides is important from the standpoint of mobility of actinides in the environment, disposal of radioactive wastes in deep geological formation, remediation of contaminated soils and materials, and development of strategies for the long-term stewardship of the contaminated sites. The microbiology research group in Japan Atomic Energy Research Institute (JAERI) is conducting basic scientific research on microbial interactions with actinides. Fundamental research on microbial transformations of actinides include elucidation of the mechanisms of dissolution and precipitation of various chemical forms such as ionic, oxides, organic and inorganic complexes of actinides by aerobic or anaerobic microorganisms under relevant microbial process conditions. State-of-the-art analytical techniques are used to determine the interaction of actinides with microorganisms at the molecular level to understand the structure function relationship. These techniques include time-resolved laser fluorescence spectroscopy (TRLFS) to determine the coordination number, oxidation states and the nearest neighbor by X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) at the Synchrotron Light Source, identification of functional groups by nuclear magnetic resonance (NMR), determination of chemical forms by transmission electron microscopy (TEM), and genomic (DNA) manipulation by molecular techniques. We here report the present status of our research activities on accumulation of lanthanides(III) by microorganisms, application of micro-particle induced X

  8. Atomic data for heavy element impurities in fusion reactors. Summary report of first IAEA research co-ordination meeting

    Clark, R.E.H.

    2006-01-01

    Twelve international experts discussed in detail the properties of heavy elements relevant to fusion energy research participated at the first Research Coordination Meeting (RCM) of the Coordinated Research Project (CRP) on 'Atomic data for heavy element impurities in fusion reactors' at IAEA Headquarters on 14-15 November 2005. The participants summarized all recent relevant developments in their research efforts. Detailed discussions took place to formulate specific objectives for the CRP. From a list of data needs and a review of current research capabilities, a detailed work plan was formulated for the first phase of the CRP. The discussions, conclusions and recommendations of the RCM are briefly described in this report. (author)

  9. Atomic data for heavy element impurities in fusion reactors. Summary report of the final research coordination meeting

    Clark, R.E.H.

    2009-04-01

    Eleven experts on the properties of heavy elements of relevance to fusion energy research attended the final Research Coordination Meeting (RCM) on Data for Heavy Element Impurities in Fusion Reactors, held at IAEA Headquarters on 4-6 March 2009. Participants summarized their accomplishments with respect to the revised work plan formulated at the second RCM. The overall work plan for the CRP was assessed and reviewed in detail, and achievements were noted. Discussions, conclusions and recommendations of the RCM are briefly described in this report. (author)

  10. Heavy-element nucleosynthesis

    Mathews, G.J.

    1990-01-01

    New measurements and theoretical studies of nuclear properties, together with new astronomical data on the growth of heavy-element abundances during the early history of the Galaxy, now provide a clearer picture of where in nature the elements heavier than iron are produced by rapid (r-process) and show (s-process) neutron capture reactions. The nuclear data suggest that the r-process involves a high-neutron-density beta-flow equilibrium environment and that the s-process may have occurred at a temperature and neutron density consistent with a 13 C(α,n) 16 0 neutron source. The astronomical data, when compared with simple galactic chemical evolution modes, suggests that the r-process is associated with type II supernovae and that the neutron source must be manufactured by the star. Low-mass type II supernovae are proposed as the most important contributors to the r-process. A 13 C neutron source in intermediate-mass stars is proposed for the s-process. 64 refs., 7 figs

  11. The WWER fuel element safety research under the design and heavy accident imitation on the 'PARAMETR' stand

    Deniskin, V.P.; Nalivaev, V.I.; Parshin, N. Ya.; Fedik, I.I.

    2000-01-01

    Analysis of fuel element behavior in the course of the design and heavy accidents is the component of reactor facility safety prevention. Many tasks of fuel element behavior research may be solved with the help of thermophysical stands. One of such stands implemented in 1991 was thermophysical stand 'PARAMETER'.Several experiments on model assemblies chiefly imitating both heavy accident and design basic accident have already been conducted in 'PARAMETER' stand. There were obtained data about fuel claddings seal failure and deformation condition. In particular it was defined that seal failure of all fuel claddings occurs on stage of fuel element warming, in temperature range (770-900) degree celsius and almost does not depend on inner pressure level

  12. Nuclear physics and heavy element research at Lawrence Livermore National Laboratory

    Stoyer, Mark A; Ahle, L E; Becker, J A; Bernshein, L A; Bleuel, D L; Burke, J T; Dashdorj, D; Henderson, R A; Hurst, A M; Kenneally, Jacqueline M; Lesher, S R; Moody, K J; Nelson, S L; Norman, E B; Pedretti, M; Scielzo, N D; Shaughnessy, D A; Sheets, S A; Stoeffl, W; Stoyer, N J [Lawrence Livermore National Laboratory, University of California, Livermore (United States)

    2009-12-31

    This paper highlights some of the current basic nuclear physics research at Lawrence Livermore National Laboratory (LLNL). The work at LLNL concentrates on investigating nuclei at the extremes. The Experimental Nuclear Physics Group performs research to improve our understanding of nuclei, nuclear reactions, nuclear decay processes and nuclear astrophysics; an expertise utilized for important laboratory national security programs and for world-class peer-reviewed basic research.

  13. Evaluation of Segmented Amorphous-Contact Planar Germanium Detectors for Heavy-Element Research

    Jackson, Emily G.

    The challenge of improving our understanding of the very heaviest nuclei is at the forefront of contemporary low-energy nuclear physics. In the last two decades, "in-beam" spectroscopy experiments have advanced from Z=98 to Z=104, Rutherfordium, allowing insights into the dynamics of the fission barrier, high-order deformations, and pairing correlations. However, new detector technologies are needed to advance to even heavier nuclei. This dissertation is aimed at evaluating one promising new technology; large segmented planar germanium wafers for this area of research. The current frontier in gamma-ray spectroscopy involves large-volume (>9 cm thick) coaxial detectors that are position sensitive and employ gamma-ray "tracking". In contrast, the detectors assessed in this dissertation are relatively thin (~1 cm) segmented planar wafers with amorphous-germanium strip contacts that can tolerate extremely high gamma-ray count rates, and can accommodate hostile neutron fluxes. They may be the only path to heavier "in-beam" spectroscopy with production rates below 1 nanobarn. The resiliency of these detectors against neutron-induced damage is examined. Two detectors were deliberately subjected to a non-uniform neutron fluence leading to considerable degradation of performance. The neutrons were produced using the 7Li(p, n)7Be reaction at the UMass Lowell Van-de-Graaff accelerator with a 3.7-MeV proton beam incident on a natural Li target. The energy of the neutrons emitted at zero degrees was 2.0 MeV, close to the mean energy of the fission neutron spectrum, and each detector was exposed to a fluence >3.6 x109 n/cm2. A 3-D software "trap-corrector" gain-matching algorithm considerably restored the overall performance. Other neutron damage mitigation tactics were explored including over biasing the detector and flooding the detector with a high gamma-ray count rate. Various annealing processes to remove neutron damage were investigated. An array of very large diameter

  14. Octupole correlations in the heavy elements

    Chasman, R.R.

    1986-01-01

    The effects of octupole correlations on the nuclear structure of the heavy elements are discussed. The cluster model description of the heavy elements is analyzed. The relevance of 2 6 -pole deformation and fast El transitions to an octupole model is considered. 30 refs., 21 figs., 1 tab

  15. [Relativistic heavy ion research

    1991-01-01

    The present document describes our second-year application for a continuation grant on relativistic heavy-ion research at Nevis Laboratories, Columbia University, over the two-year period starting from November 15, 1990. The progress during the current budget year is presented. This year, construction of RHIC officially began. As a result, the entire Nevis nuclear physics group has made a coherent effort to create new proposal for an Open Axially Symmetric Ion Spectrometer (OASIS) proposal. Future perspectives and our plans for this proposal are described

  16. Actinide targets for the synthesis of super-heavy elements

    Roberto, J.B.; Alexander, C.W.; Boll, R.A.; Burns, J.D.; Ezold, J.G.; Felker, L.K.; Hogle, S.L.; Rykaczewski, K.P.

    2015-01-01

    Since 2000, six new super-heavy elements with atomic numbers 113 through 118 have been synthesized in hot fusion reactions of "4"8Ca beams on actinide targets. These target materials, including "2"4"2Pu, "2"4"4Pu, "2"4"3Am, "2"4"5Cm, "2"4"8Cm, "2"4"9Cf, and "2"4"9Bk, are available in very limited quantities and require specialized production and processing facilities resident in only a few research centers worldwide. This report describes the production and chemical processing of heavy actinide materials for super-heavy element research, current availabilities of these materials, and related target fabrication techniques. The impact of actinide materials in super-heavy element discovery is reviewed, and strategies for enhancing the production of rare actinides including "2"4"9Bk, "2"5"1Cf, and "2"5"4Es are described.

  17. Photodisintegration of the heavy elements

    Parsons, R W; Collie, C H

    1950-08-01

    The photothresholds for the emission of neutrons by the following elements have been determined; the threshold in MeV is given in the brackets following the symbol: Pt(6.1 +- 0.1), Au(8.1 +- 0.1), Hg(6.6 +- 0.2), Tl(7.3 +- 0.25), Pb(6.9 +- 0.1), Bi(7.2 +- 0.1), Th(6.9 +- 0.15), U(5.8 +- 0.15). The neutrons were detected by the Szilard-Chalmers method of chemical concentration and the ..gamma.. rays were obtained from a small betatron. Rough values of the total cross sections can be estimated from the results.

  18. Lattice results for heavy light matrix elements

    Soni, A.

    1994-09-01

    Lattice results for heavy light matrix elements are reviewed and some of their implications are very briefly discussed. Despite the fact that in most cases the lattice results for weak matrix elements at the moment have only a modest accuracy of about 20--30% they already have important phenomenological repercussions; e.g. for V td /V ts , x s /x d and B → K*γ

  19. Heavy metals and related trace elements

    Leland, H.V.; Luoma, S.N.; Wilkes, D.J.

    1977-01-01

    A review is given of heavy metals and related trace elements in the aquatic environment. Other reviews and bibliographies are cited, dealing with the metabolism and transport of metal ions and with the toxic effects of stable and radioactive trace metals on aquatic organisms. The sources of trace elements in natural waters are discussed. It is suggested that atmospheric inputs of several trace metals comprise sizable fractions of total inputs to the Great Lakes and continental shelf waters. Information on stack emissions of trace elements from a coal-fired steam plant was used to estimate the likely range of air concentrations and inputs to a forested watershed in Tennessee. Some basic concepts of cycling of elements through aquatic communities were examined, such as the Pb, Mn and Zn concentrations in sediment and estuarine plants and animals colonizing dredge-spoil disposal areas. The use of plants as biological indicators of trace element contamination was outlined, as well as bioaccumulation in aquatic fauna. The effects of environmental factors on the kinetics of element exchange were noted, for example the influx rates of Cs 137 in tubificid worms, and Co 60 and Zn 65 in shrimp were shown to be temperature dependent. The toxicity of heavy metals on aquatic fauna was discussed, such as the histopathological lesions in the kidney and liver of fishes caused by heavy metals, and the effects of Hg and Cu on the olfactory response of rainbow trout

  20. [Relativistic heavy ion research

    1990-01-01

    At Brookhaven National Laboratory, participation in the E802 Experiment, which is the first major heavy-ion experiment at the BNL-AGS, was the main focus of the group during the past four years. The emphases of the E802 experiment were on (a) accurate particle identification and measurements of spectra over a wide kinematical domain (5 degree LAB < 55 degree, p < 20 GeV/c); and (b) measurements of small-angle two-particle correlations, with event characterization tools: multiplicity array, forward and large-angle calorimeters. This experiment and other heavy ion collision experiments are discussed in this report

  1. Frontiers of heavy-ion physics and superheavy elements

    Muenzenberg, Gottfried

    2002-01-01

    This contribution will focus on three topics of GSI nuclear structure research: super heavy elements, direct mass measurements in the storage ring, and the measurement of spallation cross section in reversed kinematics. The GSI project for an extended synchrotron facility will be outlined. (author)

  2. Frontiers of heavy element nuclear and radiochemistry

    Hoffman, D.C.

    1999-01-01

    The production and half-lives of the heaviest chemical elements, now known through Z=112, are reviewed. Recent experimental evidence for the stabilization of heavy element isotopes due to proximity to deformed nuclear shells at Z=108 and N=162 is compared with the theoretical predictions. The possible existence of isotopes of elements 107-110 with half-lives of seconds or longer, and production reactions and experimental techniques for increasing the overall yields of such isotopes in order to study both their nuclear and chemical properties are discussed. The present status of studies of the chemical properties of Rf, Ha, and Sg is briefly summarized and prospects for extending chemical studies beyond Sg are considered. (author)

  3. Heavy element affinities in Apollo 17 samples

    Allen, R.O. Jr.; Jovanovic, S.; Reed, G.W. Jr.

    1975-01-01

    204 Pb, Bi, Tl and Zn in samples from Apollo 17 exhibit relationships not found in samples from other sites. 204 Pb, Tl and Zn in residues remaining after dilute acid leaching are correlated with one another. Orange soil 74220, which is enriched in 204 Pb, Tl and Zn, is included in these relationships. In addition the submicron metallic phase generally associated with agglutinate formation is correlated with all three of these elements; this relationship has already been reported for 204 Pb in other samples. Thus, orange soil and agglutinates appear to be involved in concentrating heavy volatile metals. A process other than mixing is required to account for this. As a consequence of the isolation of the landing site by the surrounding massifs, local supply and recycling of volatile trace elements in soils may account for some of the interelement relations. (Auth.)

  4. Relativistic heavy ion research

    1992-01-01

    Experimental work is reported on the following topics: transverse energy production in 10.7-GeV/c/u Au on Au collisions; first results on delta ray production and charged particle multiplicities with the Au beam at 10.7 GeV/c/A; preliminary studies on the feasibility of flow measurement with the E814 participant calorimeter; preliminary results from the E877 telescope; and low-p t baryon distribution in Si+Al, Pb collisions at the AGS. Then the status of the Hadronic Calorimeter project of AGS Experiment E864 (ECOS--Exotic Composite Object Spectrometer) is reviewed. Next, the same is done for work of the STAR RHIC collaboration (Silicon Vertex Tracker (SVT) project evolution and development in FY92, SVT software results from 1992, SVT instrumentation, FY93 SVT pion test beam). The instrumentation section deals with the design and installation of a target rapidity telescope for BNL experiment 814/877 and a repair scheme for the E814/E877 participant calorimeter. Finally, the theory part addresses bosonic kinetics: thermalization of mesons and the pion p perpendicular spectrum in ultrarelativistic heavy-ion collisions and non-equilibrium properties of hadronic mixtures

  5. Heavy element abundances of Nova Cygni 1975

    Ferland, G.J.; Shields, G.A.

    1978-01-01

    McDonald observations of the nebular phase of the outburst of Nova Cygni 1975 are analyzed to measure the abundances of several heavy elements. A new analytical procedure is used to derive the electron density and temperature from the emission line intensities of [O III], [Ne III], and He I observed between days 40 and 120. These physical conditions are used to derive the abundances. We find that Fe has approximately a solar abundance, whereas C, N, O, and Ne are enhanced by factors approx.20 to 100. The enhanced abundance of neon was theoretically unexpected.The derived physical conditions and line intensities are compared with predictions of an equilibrium photoionization model. The model successfully predicts the intensities of He I, [O III], and [Ne III]; but it underestimates the strength of [Ne V] and [Fe VII], which may originate in a mechanically heated ''subcoronal'' line region

  6. MEGHNAD – A multi element detector array for heavy ion collision ...

    When heavy ion beam available from such machines fall on a target and undergo collision, very rich and often pristine fields of research open up. In order to carry on such activities, we have taken up a project to build a multi element gamma, heavy ion and neutron array of detectors (MEGHNAD) to detect and study the ...

  7. Element Distribution and Multiplicity of Heavy Fragments

    2002-01-01

    This experiment will measure the energy and angular distribution of heavy fragments produced in the reactions of |1|2C on several targets between |2|7Al and |2|3|8U at 86~MeV/u. The systematic investigation of a highly excited interaction region (fireball) by means of a clean N and Z identification of heavy tar fragments, may result in a better understanding of temperature concept and of the degree of equilibration of the local interaction region with respect to the total system. For this investigation a large-area position sensitive ionization chamber of 50~msr solid angle in conjunction with a time-of-flight telescope consisting of parallel-plate detectors will be used. \\\\ \\\\ In order to get information on the transverse momentum transfer and the inelasticity of the collision, the energy of the PROJECTILE-FRAGMENTS will be measured at forward angles with a plastic scintillator hodoscope. In addition to this inclusive measurement correlations between heavy fragments will be investigated by means of three pos...

  8. International cooperation in heavy-ion research

    Tobias, C.A.

    1980-01-01

    The rapidly growing research applications of heavy ions in basic biology and medicine have stimulated interest in this field in many countries. LBL, with its unique facilities and its scientific programs, is the focal point of interest. Plans are underway in several countries, including France, Japan, West Germany, and Canada, to build heavy-ion facilities, and to collaborate with our staff at LBL in heavy-ion research in physics, biology, and medicine

  9. Commissioning a Rotating Target Wheel Assembly for Heavy Element Studies

    Fields, L. D.; Bennett, M. E.; Mayorov, D. A.; Folden, C. M.

    2013-10-01

    The heaviest elements are produced artificially by fusing nuclei of light elements within an accelerator to form heavier nuclei. The most direct method to increase the production rate of nuclei is to increase the beam intensity, necessitating the use of a rotating target to minimize damage to the target by deposited heat. Such a target wheel was constructed for heavy element research at Texas A&M University, Cyclotron Institute, consisting of a wheel with three banana-shaped target cutouts. The target is designed to rotate at 1700 rpm, and a fiber optic cable provides a signal to trigger beam pulsing in order to avoid irradiating the spokes between target segments. Following minor mechanical modifications and construction of a dedicated electrical panel, the rotating target assembly was commissioned for a beam experiment. A 15 MeV/u beam of 20Ne was delivered from the K500 cyclotron and detected by a ruggedized silicon detector. The beam pulsing response time was characterized as a function of the rational frequency of the target wheel. Preliminary analysis suggests that the K500 is capable of pulsing at rates of up to 250 Hz, which is sufficient for planned future experiments. Funded by DOE and NSF-REU Program.

  10. Environmental research on actinide elements

    Pinder, J.E. III; Alberts, J.J.; McLeod, K.W.; Schreckhise, R.G.

    1987-08-01

    The papers synthesize the results of research sponsored by DOE's Office of Health and Environmental Research on the behavior of transuranic and actinide elements in the environment. Separate abstracts have been prepared for the 21 individual papers

  11. Heavy-Ion Fusion Accelerator Research, 1991

    1992-03-01

    This report discusses the following topics: research with multiple- beam experiment MBE-4; induction linac systems experiments; and long- range research and development of heavy-ion fusion accelerators

  12. THE PROPERTIES OF HEAVY ELEMENTS IN GIANT PLANET ENVELOPES

    Soubiran, François; Militzer, Burkhard [Department of Earth and Planetary Science, University of California, Berkeley, CA 94720 (United States)

    2016-09-20

    The core-accretion model for giant planet formation suggests a two-layer picture for the initial structure of Jovian planets, with heavy elements in a dense core and a thick H–He envelope. Late planetesimal accretion and core erosion could potentially enrich the H–He envelope in heavy elements, which is supported by the threefold solar metallicity that was measured in Jupiter’s atmosphere by the Galileo entry probe. In order to reproduce the observed gravitational moments of Jupiter and Saturn, models for their interiors include heavy elements, Z , in various proportions. However, their effect on the equation of state of the hydrogen–helium mixtures has not been investigated beyond the ideal mixing approximation. In this article, we report results from ab initio simulations of fully interacting H–He– Z mixtures in order to characterize their equation of state and to analyze possible consequences for the interior structure and evolution of giant planets. Considering C, N, O, Si, Fe, MgO, and SiO{sub 2}, we show that the behavior of heavy elements in H–He mixtures may still be represented by an ideal mixture if the effective volumes and internal energies are chosen appropriately. In the case of oxygen, we also compute the effect on the entropy. We find the resulting changes in the temperature–pressure profile to be small. A homogeneous distribution of 2% oxygen by mass changes the temperature in Jupiter’s interior by only 80 K.

  13. Review of even element super-heavy nuclei and search for element 120

    Hofmann, S. [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Goethe-Universitaet Frankfurt, Institut fuer Physik, Frankfurt (Germany); Heinz, S.; Mann, R.; Maurer, J.; Barth, W.; Burkhard, H.G.; Dahl, L.; Kindler, B.; Kojouharov, I.; Lang, R.; Lommel, B.; Runke, J.; Scheidenberger, C.; Schoett, H.J.; Tinschert, K. [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Muenzenberg, G. [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Manipal University, Manipal Centre for Natural Sciences, Manipal, Karnataka (India); Antalic, S.; Saro, S. [Comenius University, Department of Nuclear Physics and Biophysics, Bratislava (Slovakia); Eberhardt, K.; Thoerle-Pospiech, P.; Trautmann, N. [Johannes Gutenberg-Universitaet Mainz, Mainz (Germany); Grzywacz, R. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); University of Tennessee, Knoxville, TN (United States); Hamilton, J.H. [Vanderbuilt University, Department of Physics and Astronomy, Nashville, TN (United States); Henderson, R.A.; Kenneally, J.M.; Moody, K.J.; Shaughnessy, D.A.; Stoyer, M.A. [Lawrence Livermore National Laboratory, Livermore, CA (United States); Miernik, K. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); University of Warsaw, Warsaw (Poland); Miller, D. [University of Tennessee, Knoxville, TN (United States); Morita, K. [RIKEN Nishina Center for Accelerator-Based Science, Wako, Saitama (Japan); Nishio, K. [Japan Atomic Energy Agency, Tokai, Ibaraki (Japan); Popeko, A.G.; Yeremin, A.V. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Roberto, J.B.; Rykaczewski, K.P. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Uusitalo, J. [University of Jyvaeskylae, Department of Physics, Jyvaeskylae (Finland)

    2016-06-15

    The reaction {sup 54}Cr + {sup 248}Cm was investigated at the velocity filter SHIP at GSI, Darmstadt, with the intention to study production and decay properties of isotopes of element 120. Three correlated signals were measured, which occurred within a period of 279ms. The heights of the signals correspond with the expectations for a decay sequence starting with an isotope of element 120. However, a complete decay chain cannot be established, since a signal from the implantation of the evaporation residue cannot be identified unambiguously. Measured properties of the event chain are discussed in detail. The result is compared with theoretical predictions. Previously measured decay properties of even element super-heavy nuclei were compiled in order to find arguments for an assignment from the systematics of experimental data. In the course of this review, a few tentatively assigned data could be corrected. New interpretations are given for results which could not be assigned definitely in previous studies. The discussion revealed that the cross-section for production of element 120 could be high enough so that a successful experiment seems possible with presently available techniques. However, a continuation of the experiment at SHIP for a necessary confirmation of the results obtained in a relatively short irradiation of five weeks is not possible at GSI presently. Therefore, we decided to publish the results of the measurement and of the review as they exist now. In the summary and outlook section we also present concepts for the continuation of research in the field of super-heavy nuclei. (orig.)

  14. Heavy-Ion Fusion Accelerator Research, 1992

    1993-06-01

    The National Energy Strategy calls for a demonstration IFE power plant by the year 2025. The cornerstone of the plan to meet this ambitious goal is research and development for heavy-ion driver technology. A series of successes indicates that the technology being studied by the HIFAR Group -- the induction accelerator -- is a prime candidate for further technology development toward this long-range goal. The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions; the understanding of the scaling laws that apply in this hitherto little-explored physics regime; and the validation of new, potentially more economical accelerator strategies. Key specific elements to be addressed include: fundamental physical limits of transverse and longitudinal beam quality; development of induction modules for accelerators, along with multiple-beam hardware, at reasonable cost; acceleration of multiple beams, merging of the beams, and amplification of current without significant dilution of beam quality; final bunching, transport, and focusing onto a small target. In 1992, the HIFAR Program was concerned principally with the next step toward a driver: the design of ILSE, the Induction Linac Systems Experiments. ILSE will address most of the remaining beam-control and beam-manipulation issues at partial driver scale. A few parameters -- most importantly, the line charge density and consequently the size of the ILSE beams -- will be at full driver scale. A theory group closely integrated with the experimental groups continues supporting present-day work and looking ahead toward larger experiments and the eventual driver. Highlights of this long-range, driver-oriented research included continued investigations of longitudinal instability and some new insights into scaled experiments with which the authors might examine hard-to-calculate beam-dynamics phenomena

  15. Environmental research on actinide elements

    Pinder, J.E. III; Alberts, J.J.; McLeod, K.W.; Schreckhise, R.G. (eds.)

    1987-08-01

    The papers synthesize the results of research sponsored by DOE's Office of Health and Environmental Research on the behavior of transuranic and actinide elements in the environment. Separate abstracts have been prepared for the 21 individual papers. (ACR)

  16. Nuclear research with heavy ions

    Kaplan, M.

    1991-08-01

    This report discusses the following topics: Asymmetric fission of 149 Tb* from the finite-range, rotating-liquid-drop model: mean total kinetic energies for binary fragmentation; charged-particle evaporation from hot composite nuclei: evidence over a broad Z range for distortions from cold nuclear profiles; the role of reversed kinematics and double kinematic solutions in nuclear reactions studies; production of intermediate-mass-fragments in the reaction 98 Mo + 51 V at an excitation energy E* = 224-MeV; emission of light charged particles in the reaction 344-MeV 28 Si + 121 Sb; continued developments of the statistical evaporation code LILITA N90; and planning for heavy-ion-collision studies at very high energies: the STAR collaboration at RHIC

  17. Revamped half-lives of super heavy elements (SHE) in trans-actinide region

    Carmel Vigila Bai, G.M.; Umai Parvathiy, J.

    2015-01-01

    Analyzation of alpha decay properties and identification of Island of Stability has illuminated the theories of nuclear physics. This fundamental scientific research is the current ongoing work in the field of super heavy elements. In order to study the decay properties of super heavy elements a realistic model called as Cubic plus Yukawa plus Exponential (CYE) model is used here. This model uses a cubic potential in the pre-scission region connected by Coulomb plus Yukawa plus Exponential potential in the post scission region

  18. Placental transfer of the actinides and related heavy elements

    Sikov, M.R.

    1987-01-01

    This manuscript presents a selective review of the literature dealing with prenatal exposure of experimental animals and humans to actinides and related heavy elements, and uses this information to consider comparative aspects of placental transfer and fetoplacental distribution. General patterns have been derived from typical quantitative values, and used to compare similarities and dissimilarities, and to examine factors responsible for observed differences. 37 refs.; 1 figure; 2 tabs

  19. Nucleosynthesis of heavy elements by the photonuclear reaction

    Hayakawa, Takehito

    2002-01-01

    Nucleosynthesis of heavy elements is important for understanding of the site mechanism in the stellar and cosmochronology. The nuclei heavier than iron have been synthesized mainly by the s-process and the β-decay after the r-process. The light isotope p-nuclei produced by the photonuclear reaction in Type II supernovae explosions. In order to understand the role of each process, the ratios of the processes are calculated. I propose the experimental plan using the photon sources. (author)

  20. Coefficients of viscosity for heavy impurity element in tokamak

    El-Sharif, R N; Bekhit, A M [Plasma Physics dept., NRC, Atomic energy Authority, Cairo, (Egypt)

    1997-12-31

    The transport of heavy impurity element in to tokamak was studied theoretically. The viscosity coefficients of chromium impurities has been calculated in 13 and 21 moment approximation, in the limit of strong fields where is the gyrofrequency of species it was found that the off diagonal coefficient approximately tends to zero. This means that the friction force in the off-diagonal direction is very small, for the perpendicular viscosity coefficient the two approximation coincide to each other. 3 figs.

  1. Non destructive SXRF analysis of heavy elements in lichens

    Ramos, M.T.; Figueiredo, M.O.; Pereira da Silva, T.; Basto, M.J.; Chevallier, P.

    2000-01-01

    Various species incrusting granitic and calcareous rocks were collected at different places covering a large span of atmospheric conditions. They were chemically studied by synchrotron- induced X-ray fluorescence (SXRF), a nondestructive technique of outmost importance in the field, allowing for a future use of the same lichen fragments in further tests. This study proved that lichens - at least the saxicolous species - concentrate heavy elements recognized as strong pollutants, like lead and bromine, irrespective the environmental availability of these elements, either in the atmosphere or in the rock substrate, partially frustrating the use of saxicolous lichens as pollution monitors. (author)

  2. AMS advances in the geosciences and heavy-element analysis

    Rucklidge, J.C.; Wilson, G.C.; Kilius, L.R.

    1990-01-01

    Until recently small accelerators, such as the 2 MV Tandetron, have been used only for the lighter elements such as 10 Be, 14 C and 26 Al, while the heavier isotopes such as 36 Cl, 41 Ca and 129 I have been perceived to need the higher energies only available on large machines. We describe the use of a Tandetron for measurement of 129 I/ 127 I at natural levels, and the in situ assay of some heavy elements of interest in economic geology at detection levels superior to those of more widely used techniques. A few recently described novel applications of AMS are also given. (orig.)

  3. The radioactivity of spirulina and its heavy elements

    Fantariandraintsoa, A.A.

    2014-01-01

    Spirulina is one of the three classes of algae that have the ability to accumulate contaminants from the environment in which they live. The main aim of this work is to study the radioactive contamination of Spirulina using gamma spectrometry and to determine its content of heavy elements using the technique of X-ray fluorescence analysis. Use of detector and Gamma Vision software, in the laboratory of nuclear analysis of the I nstitut National des Sciences et Techniques Nucleaires -Madagascar (INSTN-Madagascar), allowed us to find some amount of radioactive elements such as potassium, lead, thallium and bismuth. The elements found in the laboratory of X-ray fluorescence analysis, of the same institute, using the conventional method along with the XRF AXIL software are calcium, iron, magnesium, bromine, rubidium and strontium as well as heavy elements zinc and copper. Spirulina is rich in potassium, its activity is 98±56 Bq.Kg -1 and the average concentration of the radioactive element is 16.2 g.Kg -1 . Analysis results leads us to say that it is best to consume spirulina from well secured against pollution (greenhouse) culture and we can say that we need to improve crops in natural environments. [fr

  4. Heavy-ion fusion accelerator research, 1989

    1990-06-01

    This report discusses the following topics on heavy-ion fusion accelerator research: MBE-4: the induction-linac approach; transverse beam dynamics and current amplification; scaling up the results; through ILSE to a driver; ion-source and injector development; and accelerator component research and development

  5. Quasifission in heavy and superheavy element formation reactions

    Hinde, D.J.; Dasgupta, M.; Jeung, D.Y.; Mohanto, G.; Prasad, E.; Simenel, C.; Walshe, J.; Wahkle, A.; Williams, E.; Carter, I.P.; Cook, K.J.; Kalkal, Sunil; Rafferty, D.C.; Rietz, R. du; Simpson, E.C.; David, H.M.; Düllmann, Ch.E.; Khuyagbaatar, J.

    2016-01-01

    Superheavy elements are created in the laboratory by the fusion of two heavy nuclei. The large Coulomb repulsion that makes superheavy elements decay also makes the fusion process that forms them very unlikely. Instead, after sticking together for a short time, the two nuclei usually come apart, in a process called quasifission. Mass-angle distributions give the most direct information on the characteristics and time scales of quasifission. A systematic study of carefully chosen mass-angle distributions has provided information on the global trends of quasifission. Large deviations from these systematics reveal the major role played by the nuclear structure of the two colliding nuclei in determining the reaction outcome, and thus implicitly in hindering or favouring superheavy element production.

  6. Beginnings and advances in heavy ion research

    Brix, P.

    1979-01-01

    The very important field of heavy ion research is briefly reviewed from the beginnings up to the present time. The article was intended to be a scientific lecture for the general public read on the occasion of the 70th birthday of Prof. Schmelzer. (KBE)

  7. Holifield Heavy Ion Research Facility: Users handbook

    Auble, R.L.

    1987-01-01

    The primary objective of this handbook is to provide information for those who plan to carry out research programs at the Holifield Heavy Ion Research Facility (HHIRF) at Oak Ridge National Laboratory. The accelerator systems and experimental apparatus available are described. The mechanism for obtaining accelerator time and the responsibilities of those users who are granted accelerator time are described. The names and phone numbers of ORNL personnel to call for information about specific areas are given

  8. The Origin and Distribution of Heavy Elements in HCG 62

    Vrtilek, Jan; Lavoie, Anthony R. (Technical Monitor)

    2000-01-01

    We present recent data on the compact group HCG 62 taken with AXAF CCD Imaging Spectrometer-S (ACIS-S) on Chandra. The sparseness of groups and their relatively simple dynamical history allow the properties of the Intergalatic Medium (IGM) to be more directly related to galaxy evolution than may be possible in clusters, and their lower gas temperatures produce strong lines from a broader range of elements than is the case in hotter clusters. This observation exploits the high X-ray brightness of HCG 62 to determine accurately the abundances of heavy elements as a function of position in the group, to test whether abundance variations are associated with individual galaxies, and to trace the origin of the enrichment.

  9. On the production of heavy elements by cold fusion

    Armbruster, P.

    1985-01-01

    After a short historical introduction (Section 1), this article presents new insights into the mechanism limiting the fusion of heavy nuclides (Section 2). Fusion is finally limited by the increasing Coulomb forces in the formation process of a compound system, as well as in its deexcitation. Moreover, nuclear structure effects in all stages of evaporation residue (EVR) formation are shown to be of importance. The wide field of fusion reaction studies and possible experimental techniques is projected onto the task of element synthesis, and only those aspects that are of relevance here are covered. The better understanding of EVR formation (Section 2) and the new experimental techniques (Section 3) that enabled the production of elements 107-109 (Section 4) are also discussed. In Section 5 ground-state properties and the nuclear structure of the heaviest isotopes, together with their production cross sections, are discussed. Finally, an outlook on how eventually to go beyond Z = 109 is given

  10. Frontiers of heavy-ion physics and superheavy elements

    Muenzenberg, G.

    2003-01-01

    This contribution will focus on three topics of GSI nuclear structure research: superheavy elements, direct mass measurements in the storage ring, and studies of fission in reversed kinematics. The GSI project for a new synchrotron facility will be outlined

  11. Reaction mechanisms for the synthesis of the heaviest elements from heavy ion reactions

    Gaeggeler, H.W.

    1988-10-01

    This review paper concerns fusion reactions with light heavy-ions, cold fusion, transfer reactions using light heavy-ions or heavy ions. In two appendices, methods for the separation and detection of nuclides in the domain of heaviest elements are described and a comment on the discovery of the element 104 is given. 51 figs., 10 tabs., 335 refs

  12. Overview of US heavy ion fusion research

    Logan, G.; Bieniosek, F.; Celata, C.; Henestroza, E.; Kwan, J.; Lee, E.P.; Leitner, M.; Prost, L.; Roy, P.; Seidl, P.A.; Eylon, S.; Vay, J.-L.; Waldron, W.; Yu, S.; Barnard, J.; Callahan, D.; Cohen, R.; Friedman, A.; Grote, D.; Kireeff Covo, M.; Meier, W.R.; Molvik, A.; Lund, S.; Davidson, R.; Efthimion, P.; Gilson, E.; Grisham, L.; Kaganovich, I.; Qin, H.; Startsev, E.; Rose, D.; Welch, D.; Olson, C.; Kishek, R.; O'Shea, P.; Haber, I.

    2005-01-01

    Significant experimental and theoretical progress has been made in the U.S. heavy ion fusion program on high-current sources, injectors, transport, final focusing, chambers and targets for high energy density physics (HEDP) and inertial fusion energy (IFE) driven by induction linac accelerators. One focus of present research is the beam physics associated with quadrupole focusing of intense, space-charge dominated heavy-ion beams, including gas and electron cloud effects at high currents, and the study of long-distance-propagation effects such as emittance growth due to field errors in scaled experiments. A second area of emphasis in present research is the introduction of background plasma to neutralize the space charge of intense heavy ion beams and assist in focusing the beams to a small spot size. In the near future, research will continue in the above areas, and a new area of emphasis will be to explore the physics of neutralized beam compression and focusing to high intensities required to heat targets to high energy density conditions as well as for inertial fusion energy. (author)

  13. Overview of US heavy ion fusion research

    Logan, B.G.; Bieniosek, F.M.; Celata, C.M.; Henestroza, E.; Kwan, J.W.; Lee, E.P.; Leitner, M.; Roy, P.K.; Seidl, P.A.; Eylon, S.; Vay, J-L.; Waldron, W.L.; Yu, S.S.; Barnard, J.J.; Callahan, D.A.; Cohen, R.H.; Friedman, A.; Grote, D.P; Covo, Kireeff M.; Meier, W.R.; Molvik, A.W.; Lund, S.M.; Davidson, R.C.; Efthimion, P.C.; Gilson, E.P.; Grisham, L.R.; Kaganovich, I.D.; Qin, H.; Startsev, E.A.; Rose, D.V.; Welch, D.R.; Olson, C.L.; Kishek, R.A.; O'Shea, P.; Haber, I.; Prost, L.R.; Prost, L.

    2004-01-01

    Significant experimental and theoretical progress has been made in the U.S. heavy ion fusion program on high-current sources, injectors, transport, final focusing, chambers and targets for high energy density physics (HEDP) and inertial fusion energy (IFE) driven by induction linac accelerators. One focus of present research is the beam physics associated with quadrupole focusing of intense, space-charge dominated heavy-ion beams, including gas and electron cloud effects at high currents, and the study of long-distance-propagation effects such as emittance growth due to field errors in scaled experiments. A second area of emphasis in present research is the introduction of background plasma to neutralize the space charge of intense heavy ion beams and assist in focusing the beams to a small spot size. In the near future, research will continue in the above areas, and a new area of emphasis will be to explore the physics of neutralized beam compression and focusing to high intensities required to heat targets to high energy density conditions as well as for inertial fusion energy

  14. Research Progress of Artificial Forest in the Remediation of Heavy Metal Contaminated Soils

    Jiafang, MA; Guangtao, MENG; Liping, HE; Guixiang, LI

    2017-01-01

    (1) Remediation of soil contaminated by heavy metals has become a hot topic in the world, and phytoremediation technology is the most widely used. (2) In addition to traditional economic benefits, ecological benefits of artificial forest have been more and more important, which are very helpful to soil polluted with heavy metals in the environment. (3) The characteristics of heavy metal pollution of soil and plantations of repair mechanism have been reviewed, and the current mining areas, wetlands, urban plantations on heavy metal elements have enriched the research results. The purpose is to find a new path for governance of heavy metal soil pollution.

  15. Heavy-ion fusion accelerator research in the USA

    Bangerter, R.O.; Godlove, T.D.; Herrmannsfeldt, W.B.; Keefe, D.

    1985-01-01

    In October 1983, a Heavy-Ion Fusion Accelerator Research programme (HIFAR) was established under the Office of Energy Research of the United States Department of Energy. The programme goal over the next several years is to establish a data base in accelerator physics and technology that can allow the potential of heavy ion fusion to be accurately assessed. Three new developments have taken place in the HIFAR programme. First, a decision has been made to concentrate the experimental programme on the development of multiple-beam induction linacs. Second, new beam transport experiments over a large number of quadrupole elements show that stable beam propagation occurs for significantly higher beam currents than had been believed possible a few years ago. Third, design calculations now show that a test accelerator of modest size and cost can come within a factor of three of testing almost all of the physics and technical issues appropriate to a power plant driver. (author)

  16. Heavy-Duty Vehicle Thermal Management | Transportation Research | NREL

    Heavy-Duty Vehicle Thermal Management Heavy-Duty Vehicle Thermal Management Infrared image of a control materials and equipment on heavy-duty vehicles. Photo by Dennis Schroeder, NREL Illustration of a Ray David, NREL National Renewable Energy Laboratory (NREL) researchers are assisting heavy-duty

  17. Estimation of atomic masses of heavy and superheavy elements

    Uno, Masahiro [Ministry of Education, Science and Culture, Tokyo (Japan)

    1997-07-01

    To estimate unknown atomic masses of heavy and superheavy elements, three kinds of formula: FRDM (finite range droplet model by Moeller et al.), TUYY (an empirical formula by Tachibana et al.) and our KUTY are explained. KUTY estimates the crude shell energies of spherical nucleus from sum of single-particle energies. Then, the refined shell energies in due consideration of paring and deformation are obtained by mixing with the functions of the crude shell energies. Experimental values of U and Fm isotopes were compared with estimation mass of KUTY and FRDM. In the field with experimental values of U isotopes, the value of KUTY and FRDM separated the same difference from the experimental value. The behavior of KUTY and FRDM for Fm isotopes were same as that of U, but ETFSI deviated a little from the experimental values. (S.Y.)

  18. Heavy accelerated nuclei in biomedical research

    Tobias, C.A.

    1987-01-01

    Accelerated atomic nuclei in physics accelerators have been used in basic biological research and in applied medical diagnostic and therapeutic studies for the past 50 years. The passage of single heavy particles through the cell nucleus is capable of producing multiple DNA double-strand scission and chromatin breaks. According to the Repair-Misrepair model, the high biological effectiveness of high-LET particles is due to misrepair and misrejoining of the breaks. The Bragg depth ionization effect allows heavy particles to deposit considerably more energy deep in tissue than at the surface, and this property has been used for great improvements in the radiation therapy of localized tumors. Recent advances in producing radioactive beams will allow verification of therapeutic administration of such beams. The radioactive beams also open a new field of Nuclear Medicine. There is increasing interest in building special biomedical light and heavy-ion accelerators. These will be used not only for therapy but also for diagnosis, for the study of radiation hazards in space flight, and for basic molecular and cellular understanding of the mechanisms of radiation effect

  19. Holifield Heavy Ion Research Facility. Phase II

    Ball, J.B.; Hudson, E.D.; Lord, R.S.; Johnson, J.W.; Martin, J.A.; McNeilly, G.S.; Milner, W.T.; Mosko, S.W.; Sayer, R.O.; Robinson, R.L.

    1979-01-01

    The Holifield Heavy Ion Research Facility, with the completion of Phase I in late 1979, will include the Oak Ridge Isochronous Cyclotron (ORIC) and associated research areas, the new 25 MV tandem accelerator with new research areas for tandem beams, and modifications to utilize the ORIC as a booster accelerator. The combination of the tandem and ORIC will provide beam energies of 25 MeV/A for light heavy ions and 6 MeV/A up to A = 160. This paper discusses plans for a Phase II expansion of the facility to include an isochronous cyclotron with superconducting magnet and reconfiguration of the existing research areas and the ORIC vault to handle the higher energy beams from the new cyclotron. The new booster cyclotron is a low-flutter high-spiral design patterned after the MSU K = 800 design, with a central magnetic field of about 5 tesla and an extraction radius of 1 meter. The new beam transport system will incorporate an rf beam-splitter system that will be able to deliver successive beam pulses to two or three experiment areas

  20. Heavy element stable isotope ratios. Analytical approaches and applications

    Tanimizu, Masaharu; Sohrin, Yoshiki; Hirata, Takafumi

    2013-01-01

    Continuous developments in inorganic mass spectrometry techniques, including a combination of an inductively coupled plasma ion source and a magnetic sector-based mass spectrometer equipped with a multiple-collector array, have revolutionized the precision of isotope ratio measurements, and applications of inorganic mass spectrometry for biochemistry, geochemistry, and marine chemistry are beginning to appear on the horizon. Series of pioneering studies have revealed that natural stable isotope fractionations of many elements heavier than S (e.g., Fe, Cu, Zn, Sr, Ce, Nd, Mo, Cd, W, Tl, and U) are common on Earth, and it had been widely recognized that most physicochemical reactions or biochemical processes induce mass-dependent isotope fractionation. The variations in isotope ratios of the heavy elements can provide new insights into past and present biochemical and geochemical processes. To achieve this, the analytical community is actively solving problems such as spectral interference, mass discrimination drift, chemical separation and purification, and reduction of the contamination of analytes. This article describes data calibration and standardization protocols to allow interlaboratory comparisons or to maintain traceability of data, and basic principles of isotope fractionation in nature, together with high-selectivity and high-yield chemical separation and purification techniques for stable isotope studies.

  1. Induction linacs for heavy ion fusion research

    Fessenden, T.J.; Avery, R.T.; Brady, V.; Bisognano, J.; Celata, C.; Chupp, W.W.; Faltens, A.; Hartwig, E.C.; Judd, D.L.; Keefe, D.; Kim, C.H.; Laslett, L.J.; Lee, E.P.; Rosenblum, S.S.; Smith, L.; Warwick, A.

    1984-01-01

    The new features of employing an induction linac as a driver for inertial fusion involve (1) transport of high-current low-emittance heavy ion beams. (2) multiple independently-focussed beams threading the same accelerator structure, and (3) synthesis of voltage waveforms to accomplish beam current amplification. A research program is underway at LBL to develop accelerators that test all these features with the final goal of producing an ion beam capable of heating matter to proportional70 eV. This paper presents a discussion of some properties of induction linacs and how they may be used for HIF research. Physics designs of the High Temperature Experiment (HTE) and the Multiple Beam Experiment (MBE) accelerators are presented along with initial concepts of the MBE induction units. (orig.)

  2. Induction linacs for heavy ion fusion research

    Fessenden, T.J.

    1984-05-01

    The new features of employing an induction linac as a driver for inertial fusion involve (1) transport of high-current low-emittance heavy ion beams, (2) multiple independently-focussed beams threading the same accelerator structure, and (3) synthesis of voltage waveforms to accomplish beam current amplification. A research program is underway at LBL to develop accelerators that test all these features with the final goal of producing an ion beam capable of heating matter to approx. 70 eV. This paper presents a discussion of some properties of induction linacs and how they may be used for HIF research. Physics designs of the High Temperature Experiment (HTE) and the Multiple Beam Experiment (MBE) accelerators are presented along with initial concepts of the MBE induction units.

  3. Elemental characterization of PM1 in a heavy traffic region

    Ambade, Balram

    Eight hours samples of airborne aerosols PM1 were collected during summer (August-September) and winter (October-November) form one year 2010- 2011 in a intense traffic area of Rajnandgaon city, India. Inductively coupled plasma mass spectroscopy was employed to measure heavy metals (Hg, Cd, Ni, Pb, As). Water-soluble ions (Na+, NH4 +, K+, Ca2+, Cl-, NO3 -, and SO42-) and carbonaceous mass (elemental and organic carbon) were detected using ion chromatograph and CHN analyzer, respectively. The results indicate that the composition of PM10 on intense traffic area is highly affected by automobile emissions. Based on the chemical information, positive matrix factorization (PMF) was used to identify PM sources. A total of five source types were identified, including soil dust, vehicle emissions, sea salt, industrial emissions and secondary aerosols, and their contributions were estimated using PMF. The crustal enrichment factors (EF) were calculated using Al as a reference for the trace metal species to identify the sources

  4. Fuel elements of research reactors in China

    Zhou Yongmao; Chen Dianshan; Tan Jiaqiu

    1987-01-01

    This paper describes the current status of design, fabrication of fuel elements for research reactors in China, emphasis is placed on the technology of fuel elements for the High Flux Engineering Test Reactor (HFETR). (author)

  5. Estimation of Heavy Elements Pollution in Sea Plants (Algae) by Using Neutron Activation Analysis

    El-Ghondi, A. A.; El-Mismary, Y. A.; Etwir, R. H.; Machiouf, M. A.; Ben Shaban, Y.; Abia, R.

    2007-01-01

    The total content of trace elements were determined in 50 samples of sea plants (macro algae) collected from Tripoli coast area (Tajura, El schab, Dat Elemad ) in Libya. The samples were investigated as an indication of heavy elements pollution. In this paper, the total amounts of Zn, Sc, Fe, Co, Cr, Ba, Cs, Sb, Rb, and Hf concentration were determined by using Neutron Activation Analysis in Tajura research center. High levels of Zn and Cr and slightly increasing in amount of Co and Fe are considered as normal values comparing with polluted area particularly with Fe and Co in investigated samples. Statistical calculation of the results have shown a positive relationship between the contents of Ba, Sc, Hf, Cr and Fe-Sb but no relation with Zn and other investigated trace elements contents. Further investigation should be carried out to confirm these findings and correlate them to source attribution.

  6. Trace elements and heavy metals in the Grand Bay National Estuarine Reserve in the northern Gulf of Mexico

    The Grand Bay National Estuarine Research Reserve has the highest biotic diversity of habitats and offer a reserve of food resources and commercially significant species. Rapid human civilization has led to accumulation of heavy metals and trace elements in estuaries. The Grand Bay National Estuarin...

  7. Unified fuel elements development for research reactors

    Vatulin, A.; Stetsky, Y.; Dobrikova, I.

    1998-01-01

    Square cross-section rod type fuel elements have been developed for russian pool-type research reactors. new fuel elements can replace the large nomenclature of tubular fuel elements with around, square and hexahedral cross-sections and to solve a problem of enrichment reduction. the fuel assembly designs with rod type fuel elements have been developed. The overall dimensions of existing the assemblies are preserved in this one. the experimental-industrial fabricating process of fuel elements, based on a joint extrusion method has been developed. The fabricating process has been tested in laboratory conditions, 150 experimental fuel element samples of the various sizes were produced. (author)

  8. Communicative Elements of Action Research

    Ryan, Thomas G.

    2013-01-01

    This review considers human communications as utilized within a research design; in this case collaborative action research (CAR), a derivative of action research (AR), to achieve outcomes that change, and move participants forward. The association between AR and CAR is a deliberate attempt by the author to draw attention to communicative actions…

  9. The Zintl Chemistry of the Heavy Tetrel Elements

    Klem, Michael Thomas [Iowa State Univ., Ames, IA (United States)

    2002-12-31

    Exploration of the alkali metal/alkaline-earth metal/heavy tetrel (Sn or Pb) systems has revealed a vast array of new chemistry and novel structure types. The structures and properties of these new materials have been studied in an attempt to understand the chemistry of these and other related systems. The first phase reported is Rb4Pb9 (K4Pb9 type). The compound contains two different types of Pb94- deltahedra, a monocapped square pyramid and a distorted tricapped trigonal prism. Both cluster geometries correspond to a nido assignment even though the tricapped trigonal prism is not the classic Wade's rules nido deltahedron expected for a monocapped square antiprism. Also, a series of compounds that contain square pyramidal Tt5 polyanions of tin and lead has been obtained in alkaline-earth or rare-earth metal-tetrel systems by direct fusion of the elements to yield Sr3Sn5, Ba3Pb5, and La3Sn5. These phases contain square pyramidal clusters of the tetrel elements that are weakly interlinked into chains via two types of longer intercluster interactions that are mediated by bridging cations and substantially influenced by cation size and the free electron count. Attempts at incorporating another main-group element to form heteroatomic clusters were also successful. In the case of A5InPb8 (A = K, Rb), the compounds contain clusters composed of two Pb4 tetrahedra that are interbridged by a lone μ6-In atom. The InPb8 units are weakly interlinked into sheets in the ab plane by long intercluster Pb-Pb interactions. Using As led to the formation of the compound K5As3Pb3 which is made up of As3Pb35- crown clusters that can be likened to a 6-atom hypho-cluster based on the tricapped trigonal parent as the closo

  10. Relativistic heavy ion research at Berkeley

    Anon.

    1981-01-01

    The project of a superconducting synchrotron for heavy ions with 1 TeV/amu is described. In this connection the physics is discussed which can be studied by this accelerator. Furthermore, the HISS-heavy ion spectrometer system and the Plastic Ball detector are described. (HSI).

  11. Heavy Metallic Element Distribution in Cisadane River Estuary's Water and Sediment

    M. Taufik Kaisupy; Abdul Rozak; Endang Rochyatun

    2006-01-01

    Observation of heavy metallic elements in Cisadane River Estuary has been done in July and November 2005. The results show that heavy metallic elements content in seawater is lower and still below the treshold value stated by government for fisheries. There was an indication of heavy metallic elements on sediment. Distribution of Pb on July and of Cu on November 2005 were found higher near the coast and decrease towards the sea, and commonly were found in front of estuary such as Cisadane, Mu...

  12. EDRXF measurements of heavy elements in soil samples from some potentially polluted sites in zambia

    Hayumbu, P.; Phiri, L.K.; Mambo, A.; Sokotela, S.B.

    2001-01-01

    A survey of heavy element levels in top soils collected around four industrial plants and along four highway stretches demonstrated that there was significant pollution only around an abandoned Pb/Zn mine. Sample collection in a rectangular grid encompassing each source sought to depict the spatial extent of pollution. Ascertaining levels of heavy elements in potentially polluted soils in urban areas of Zambia and along major highways was deemed desirable because it is common practice to grow maize and vegetables in lots adjacent to accessible industrial sites and highways. Pb is a heavy element of interest for all sampled sites whose distribution at the abandoned mine ranged from 13 to 2028 ppm

  13. The heavy water accountancy for research reactors in JAERI

    Yoshijima, Tetsuo; Tanaka, Sumitoshi; Nemoto, Denjirou

    1998-11-01

    The three research reactors have been operated by the Department of Research Reactor and used about 41 tons heavy water as coolant, moderator and reflector of research reactors. The JRR-2 is a tank type research reactor of 10MW in thermal power and its is used as moderator, coolant and reflector about 16 tons heavy water. The JRR-3M is a light water cooled and moderated pool type research reactor with a thermal power of 20MW and its is used as reflector about 7.3 tons heavy water. In the JRR-4, which is a light water cooled swimming pool type research reactor with the maximum thermal power of 3.5MW, about 1 ton heavy water is used to supply fully thermalized neutrons with a neutron beam experiment of facility. The heavy water was imported from U.S.A., CANADA and Norway. Parts of heavy water is internationally controlled materials, therefore management of heavy water is necessary for materials accountancy. This report described the change of heavy water inventories in each research reactors, law and regulations for accounting of heavy water in JAERI. (author)

  14. Research highlights from the Holifield Heavy Ion Research Facility

    Plasil, F.

    1982-01-01

    The purpose of this paper is to present the scope of research carried out at the new Holifield Heavy Ion Research Facility (HHIRF) at Oak Ridge. This will be accomplished with reference to several research projects currently underway. The areas of research represented are microscopic and macroscopic aspects of nuclear reactions and nuclear structure. In view of the scope of this conference, emphasis will be placed on nuclear reactions. A brief description of HHIRF is given, together with its current status. Microscopic aspects of reactions between nuclei are discussed with reference to the prospects for the study of giant resonances by means of heavy ions, and to studies of elastic and inelastic scattering of 60 Ni nuclei. Macroscopic aspects of nuclear reactions are illustrated by means of the study of collisions between 58 Ni nuclei at 15.1 MeV/u and by means of Spin Spectrometer (crystal ball) studies of the 19 F + 159 Tb reaction. Results are presented for lifetime measurements of high-spin states in ytterbium nuclei

  15. Heavy-Quark Effective Theory and Weak Matrix Elements

    Neubert, Matthias

    1999-01-01

    Recent developments in the theory of weak decays of heavy flavours are reviewed. Applications to exclusive semileptonic B decays, the semileptonic branching ratio and charm counting, beauty lifetimes, and hadronic B decays are discussed.

  16. Targeting heavy rare earth elements in carbonatite complexes

    Broom-Fendley, S.; Wall, F.; Gunn, A. G.; Dowman, E.

    2012-04-01

    The world's main sources of the rare earth elements (REE) are concentrated in carbonatite complexes. These have the advantages of high grade and tonnage, combined with low thorium contents, yet they are generally enriched in light rare earths (LREE). The heavy rare earths (HREE, which include Eu-Lu and Y) are more highly sought after because of their role in new and green technologies. HREE are predominantly extracted from ion-adsorption clays in China. These are small, low grade deposits, which are often illegally mined by artisans. Increased government control, environmental legislation and local demand for REE in China have led to high prices and global concerns about the security of supply of the HREE. Alternative sources of the HREE are poorly documented. We present a review of such targets, including: (1) 'abnormal' carbonatites; (2) areas around LREE-rich complexes such as breccia, fenite and latter stage veins; and (3) weathered carbonatites. At Lofdal, Namibia, carbonatite dykes contain xenotime-(Y) together with LREE minerals. The original chemistry of the carbonatite magma, coupled with late-stage magma and fluid evolution, seem to be controlling factors [1, 2]. The Khibina carbonatite, Kola Peninsula, Russia, is an example of where early LREE carbonatites become increasing HREE-enriched as magmas evolve to carbo-hydrothermal fluids [3]. Around carbonatite complexes in Malawi HREE enrichment can be found in breccia and in fenite. Breccia around Songwe shows areas with high Y/La ratios within the matrix caused by narrow zones of xenotime enrichment. Fenite around Kangankunde and Chilwa Island has higher HREE:LREE ratios than the carbonatite [4]. At weathered complexes, such as at Mount Weld in Western Australia, changes in both HREE concentration and LREE:HREE ratios are observed. In currently unworked sections of the deposit, the HREE mineral churchite (YPO4.H2O) has formed concentrations due to groundwater flow [5]. These areas of enrichment are

  17. Separation process of heavy rare earth elements from xenotime ore

    Sri Sukmajaya; Tri Handini; Wahyu Rachmi Pusparini; Dwi Biyantoro

    2016-01-01

    Separation process of heavy rare earth elements from xenotime ore had been done. A 100 mesh of xenotime ore was upgrade using water, sodium silicate and oleic acid in pH 9. Mixed of slurry by air blown in room temperature along 30 minutes. The middle of slurry xenotime was be separated, then dried and so added soda caustic, potassium carbonate and ammonium dihydrogen phosphate. The mix was be homogenized then leached in furnace to 700°C temperature along 4 hours. The frits of leaching product would be leached using 1200 mL volume of water that made oxidation by HCl onto pH 4 by agitated heated in 70°C temperature. The mix was filtered, then solid settled was be dried and then to processed again in water HCl acidified leaching alike before until pH 4 with minimized HCl added least 2 mL. The solid settled filled into 1000 mL of beker glass, added HCl viscous in 300 mL volume, hydrogen peroxide and BaCl_2/Na_2SO_4/Na_2S then heated to 100°C temperature. Let in room temperature then was filtrated. The solid settled as ThSO_4/ThS, RaSO_4/RaS. The filtrate to be settled using 15g (NH_4)_2CO_3 in 100 mL volume of water while mixed until the solution reached pH 2. The solid settled was be dried, then into the filtrate added 10 mL volume of formic acid. The solid settled of filtration was be dried. The solution of filtrate to be settled using (NH_4)_2CO_3 until pH 4. The solid settled was be filtered and dried. The filtrate was be settled using oxalic acid. The analysis of standard of oxide rare earth had been done using XRF Am"2"4"1 source. Result of these process got 100 mesh xenotime upgrade those leached in 700°C along 4 hours used (NH_4)H_2PO_4 so HRE total lifted up from 4.31 to 8.16%. Resulted of HRE oxide yield was 17.76% in pH 2. HRE oxide yield in pH 4 was 38.45%, and HRE oxide yield was 6.38% as oxalic compound, so the total HRE oxide yield was 62.59%. (author)

  18. Heavy Ion Fusion Accelerator Research (HIFAR)

    1991-04-01

    This report discusses the following topics: emittance variations in current-amplifying ion induction lina; transverse emittance studies of an induction accelerator of heavy ions; drift compression experiments on MBE-4 and related emittance; low emittance uniform- density C s + sources for heavy ion fusion accelerator studies; survey of alignment of MBE-4; time-of-flight dependence on the MBE-4 quadrupole voltage; high order calculation of the multiple content of three dimensional electrostatic geometries; an induction linac injector for scaled experiments; induction accelerator test module for HIF; longitudinal instability in HIF beams; and analysis of resonant longitudinal instability in a heavy ion induction linac

  19. Fuel enrichment reduction for heavy water moderated research reactors

    McCulloch, D.B.

    1984-01-01

    Twelve heavy-water-moderated research reactors of significant power level (5 MW to 125 MW) currently operate in a number of countries, and use highly enriched uranium (HEU) fuel. Most of these reactors could in principle be converted to use uranium of lower enrichment, subject in some cases to the successful development and demonstration of new fuel materials and/or fuel element designs. It is, however, generally accepted as desirable that existing fuel element geometry be retained unaltered to minimise the capital costs and licensing difficulties associated with enrichment conversion. The high flux Australian reactor, HIFAR, at Lucas Heights, Sydney is one of 5 Dido-class reactors in the above group. It operates at 10 MW using 80% 235 U HEU fuel. Theoretical studies of neutronic, thermohydraulic and operational aspects of converting HIFAR to use fuels of reduced enrichment have been made over a period. It is concluded that with no change of fuel element geometry and no penalty in the present HEU fuel cycle burn-up performance, conversion to MEU (nominally 45% 235 U) would be feasible within the limits of current fully qualified U-Al fuel materials technology. There would be no significant, adverse effects on safety-related parameters (e.g. reactivity coefficients) and only small penalties in reactor flux. Conversion to LEU (nominally 20% 235 U) a similar basis would require that fuel materials of about 2.3 g U cm -3 be fully qualified, and would depress the in-core thermal neutron flux by about 15 per cent relative to HEU fuelling. In qualitative terms, similar conclusions would be expected to hold for a majority of the above heavy water moderated reactors. (author)

  20. Heavy Metallic Element Distribution in Cisadane River Estuary's Water and Sediment

    M. Taufik Kaisupy

    2006-04-01

    Full Text Available Observation of heavy metallic elements in Cisadane River Estuary has been done in July and November 2005. The results show that heavy metallic elements content in seawater is lower and still below the treshold value stated by government for fisheries. There was an indication of heavy metallic elements on sediment. Distribution of Pb on July and of Cu on November 2005 were found higher near the coast and decrease towards the sea, and commonly were found in front of estuary such as Cisadane, Muara Saban and Tanjung Pasir. High Pb and Zn distributions on November 2005 were found only in front of Cisadane estuary. Cd distribution of Cisadane estuary was constant at all station but did not show any correlation with the distance of station and estuary. The Cd content on July and November 2005 is lower than 0,001 ppm. Generally, heavy metallic elements content have a uniform distribution at all stations inspite of its distance to estuary.

  1. HEAVY-ELEMENT ENRICHMENT OF A JUPITER-MASS PROTOPLANET AS A FUNCTION OF ORBITAL LOCATION

    Helled, R.; Schubert, G.

    2009-01-01

    One possible mechanism for giant planet formation is disk instability in which the planet is formed as a result of gravitational instability in the protoplanetary disk surrounding the young star. The final composition and core mass of the planet will depend on the planet's mass, environment, and the planetesimal accretion efficiency. We calculate heavy-element enrichment in a Jupiter-mass protoplanet formed by disk instability at various radial distances from the star, considering different disk masses and surface density distributions. Although the available mass for accretion increases with radial distance (a) for disk solid surface density (σ) functions σ = σ 0 a -α with α 5 years of planetary evolution, when the planet is extended and before gap opening and type II migration take place. The accreted mass is calculated for disk masses of 0.01, 0.05, and 0.1 M sun with α = 1/2, 1, and 3/2. We show that a Jupiter-mass protoplanet can accrete 1-110 M + of heavy elements, depending on the disk properties. Due to the limitation on the accretion timescale, our results provide lower bounds on heavy-element enrichment. Our results can explain the large variation in heavy-element enrichment found in extrasolar giant planets. Since higher disk surface density is found to lead to larger heavy-element enrichment, our model results are consistent with the correlation between heavy-element enrichment and stellar metallicity. Our calculations also suggest that Jupiter could have formed at a larger radial distance than its current location while still accreting the mass of heavy elements predicted by interior models. We conclude that in the disk instability model the final composition of a giant planet is strongly determined by its formation environment. The heavy-element abundance of a giant planet does not discriminate between its origin by either disk instability or core accretion.

  2. [Research advances in heavy metals pollution ecology of diatom].

    Ding, Teng-Da; Ni, Wan-Min; Zhang, Jian-Ying

    2012-03-01

    Diatom, due to its high sensitivity to environmental change, is one of the bio-indicators of aquatic ecosystem health, and some typical diatom species have been applied to indicate the heavy metals pollution of water body. With the focus on the surface water heavy metals pollution, this paper reviewed the research advances in the toxic effect of heavy metals pollution on diatom, biosorption and bioaccumulation of heavy metals by diatom, ecological adaptation mechanisms of diatom to heavy metals pollution, and roles of diatom as bio-indicator and in ecological restoration of heavy metals pollution. The growth tendency of diatom and the morphological change of frustule under heavy metals pollution as well as the differences in heavy metals biosorption and bioaccumulation by diatom, the ecological adaptation mechanisms of diatom on heavy metals surface complexation and ion exchange, and the roles of diatom as bio-indicator and in ecological restoration of heavy metals polluted water body were also discussed. This review could provide scientific evidences for the prevention of aquatic ecosystems heavy metals pollution and related early warning techniques.

  3. Heavy metal and trace elements in riparian vegetation and macrophytes associated with lacustrine systems in Northern Patagonia Andean Range.

    Juárez, Andrea; Arribére, María A; Arcagni, Marina; Williams, Natalia; Rizzo, Andrea; Ribeiro Guevara, Sergio

    2016-09-01

    Vegetation associated with lacustrine systems in Northern Patagonia was studied for heavy metal and trace element contents, regarding their elemental contribution to these aquatic ecosystems. The research focused on native species and exotic vascular plant Salix spp. potential for absorbing heavy metals and trace elements. The native species studied were riparian Amomyrtus luma, Austrocedrus chilensis, Chusquea culeou, Desfontainia fulgens, Escallonia rubra, Gaultheria mucronata, Lomatia hirsuta, Luma apiculata, Maytenus boaria, Myrceugenia exsucca, Nothofagus antarctica, Nothofagus dombeyi, Schinus patagonicus, and Weinmannia trichosperma, and macrophytes Hydrocotyle chamaemorus, Isöetes chubutiana, Galium sp., Myriophyllum quitense, Nitella sp. (algae), Potamogeton linguatus, Ranunculus sp., and Schoenoplectus californicus. Fresh leaves were analyzed as well as leaves decomposing within the aquatic bodies, collected from lakes Futalaufquen and Rivadavia (Los Alerces National Park), and lakes Moreno and Nahuel Huapi (Nahuel Huapi National Park). The elements studied were heavy metals Ag, As, Cd, Hg, and U, major elements Ca, K, and Fe, and trace elements Ba, Br, Co, Cr, Cs, Hf, Na, Rb, Se, Sr, and Zn. Geochemical tracers La and Sm were also determined to evaluate contamination of the biological tissues by geological particulate (sediment, soil, dust) and to implement concentration corrections.

  4. Research in heavy-ion nuclear physics

    Sanders, S.J.; Prosser, F.W.

    1992-01-01

    This report discusses the following topics: Fusion-fission in light nuclear systems; High-resolution Q-value measurement for the 24 Mg+ 24 Mg reaction; Heavy-ion reactions and limits to fusion; and Hybrid MWPC-Bragg curve detector development

  5. Resolving key heavy-ion fusion target issues with relativistic heavy-ion research accelerators

    Arnold, R.C.

    1988-01-01

    Heavy-ion accelerators designed for relativistic nuclear research experiments can also be adapted for target research in heavy-ion driver inertial fusion. Needle-shaped plasmas can be created that are adequate for studying basic properties of matter at high energy density. Although the ion range is very long, the specific deposited power nevertheless increases with kinetic energy, as the focus spot can be made smaller and more ions can be accumulated in larger rings

  6. LIBS detection of heavy metal elements in liquid solutions by using wood pellet as sample matrix

    Wen Guanhong; Sun Duixiong; Su Maogen; Dong Chenzhong

    2013-01-01

    Laser-induced breakdown spectroscopy (LIBS) has been applied to the analysis of heavy metals in liquid sample. A new approach was presented to improve the detection limit and minimize the sample matrix effects, in which dried wood pellets absorbed the given amounts of Cr standard solutions and then were baked because they have stronger and rapid absorption properties for liquid samples as well as simple elemental compositions. In this work, we have taken a typical heavy metal Cr element as an example, and investigated the spectral feasibility of Cr solutions and dried wood pellets before and after absorbing Cr solutions at the same experimental conditions, respectively. The results were demonstrated to successfully produce a superior analytical response for heavy metal elements by using wood pellet as sample matrix according to obtained LOD of 0.07 ppm for Cr element in solutions. (author)

  7. LIBS Detection of Heavy Metal Elements in Liquid Solutions by Using Wood Pellet as Sample Matrix

    Wen Guanhong; Sun Duixiong; Su Maogen; Dong Chenzhong

    2014-01-01

    Laser-induced breakdown spectroscopy (LIBS) has been applied to the analysis of heavy metals in liquid samples. A new approach was presented to lower the limit of detection (LOD) and minimize the sample matrix effects, in which dried wood pellets absorbed the given amounts of Cr standard solutions and then were baked because they have stronger and rapid absorption properties for liquid samples as well as simple elemental compositions. In this work, we have taken a typical heavy metal Cr element as an example, and investigated the spectral feasibility of Cr solutions and dried wood pellets before and after absorbing Cr solutions at the same experimental conditions. The results were demonstrated to successfully produce a superior analytical response for heavy metal elements by using wood pellet as sample matrix according to the obtained LOD of 0.07 ppm for Cr element in solutions

  8. A study of pollution extent in some drinking water resources by heavy elements in Hadramout governorate

    Barheyan, Saad Awadh

    2001-01-01

    The paper is considered as a preliminary study of pollution extent in some drinking water resources in Hadramout governorate by heavy elements which differ in their toxicity. The elements subjected to study are Cd, Pb, Fe, Cr, Mn, Zn, Co and Cu. Atomic absorption spectrometric method of analysis (AAS) is used for the determination of heavy elements concentrations. The elemental analysis of drinking water samples shows that the concentration of the above-mentioned elements in drinking water resources, lies in the permissible limit given by the WHO. Similarity of elements content is observed in Thela and Fuwah waters, bu the case is different for Ghail Bawzeer and Asshihir waters due to their different lithospheric structures. Drinking water used by the civilians is not subjected to physical, biological or chemical treatment which may lead to total or partial removal of heavy elements and other rejected impurities. Drinking water running in distribution nets is a hard water and has a weak base (Ph which explains the reason why heavy elements are absorbed and precipitated inside drinking water pipes before they reach consumers. This type of hard water causes accumulation of salt precipitates inside the water pipes which results in many economic and health disturbances to consumers. The slight increase of Cr, Mn, and Co concentration in drinking water flowing in the pipes may be due to the effect of some anions such as nitrates which form soluble compounds with the elements contained in the chemical composition of the drinking water pipes. This paper is a strong indicator for determination of heavy elements concentrations in different drinking water resources in Hadramout govemorate. Such approach seeks a further comprehensive work with special focus on the study of lithospheric structure of the feeding water regions of Hadramout aquifers. (author)

  9. Development of a novel heavy element chemistry apparatus using the RIKEN gas-field recoil separator as a pre-separator

    Haba, H.; Morita, K.; Enomoto, S.; Morimoto, K.; Kaji, D.; Nagame, Yuichiro

    2004-01-01

    A new system was developed, that supplied the super-heavy element separated physically as the former steps to the chemical analysis devices such as a gas or liquid chromatographs. The gas jet transportation device was newly set up on the edge of existing accelerator research facilities in the Institute of Physical and Chemical Research linac building (GARIS). To conduct the chemical separation experiment of a super-heavy element of 112 in future a radioactive isotope of mercury of light homology elements was manufactured with a gas jet uniting type online multi-tracer manufacturing device. The adsorption chromatograph experiment to the gold was performed using this system. (H. Katsuta)

  10. Unification of fuel elements for research reactors

    Vatulyn, A.V.; Stetskyi, Y.A.; Dobrikova, I.V.

    1997-01-01

    To the purpose of fuel elements unification the possibility of rod fuel assembly (FA) using in the cores of research reactors have been considered in this paper. The calculation results of geometric, hydraulic and thermotechnical parameters of rod assembly are submitted. Several designs of finned square fuel element and fuel assembly are proposed on base of analysis of rod FA characteristics in compare of tube ones. The fuel elements specimens and the model assembly are manufactured. The developed designs are the basis for further optimization after neutron-physical calculations of cores. (author)

  11. Heavy elements abundances in metal-poor stars

    Magain, P.; Jehin, E.; Neuforge, C.; Noels, A.

    1998-01-01

    A sample of 21 metal-poor stars have been analysed on the basis of high resolution and high signal-to-noise spectra. Correlations between relative abundances of 16 elements have been studied, with a special emphasis on the neutron-capture ones. This analysis reveals the existence of two sub-populations of field halo stars, namely Pop IIa and Pop IIb. They differ by the behaviour of the s-process elements versus the α and r-process elements. We suggest a scenario of formation of these stars, which closely relates the field halo stars to the evolution of globular clusters. The two sub-populations would have evaporated the clusters during two different stages of their chemical evolution

  12. Heavy flavor operator matrix elements at O({alpha}{sub s}{sup 3})

    Bierenbaum, Isabella; Buemlein, Johannes; Klein, Sebastian

    2008-12-15

    The heavy quark effects in deep.inelastic scattering in the asymptotic regime Q{sup 2}>>m{sup 2} can be described by heavy flavor operator matrix elements. Complete analytic expressions for these objects are currently known to NLO. We present first results for fixed moments at NNLO. This involves a recalculation of fixed moments of the corresponding NNLO anomalous dimensions, which we thereby confirm. (orig.)

  13. Spallation RI beam facility and heavy element nuclear chemistry

    Nagame, Yuichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-11-01

    An outline of the spallation RI (Radioactive Ion) beam facility is presented. Neutron-rich nuclides are produced in the reaction of high intensity (10-1000 {mu}A) protons with energy of 1.5 GeV and an uranium carbide target. Produced nuclides are ionized in an isotope separator on-line (ISOL) and accelerated by the JAERI tandem and the booster linac. Current progress and a future project on the development of the RI beam facility are given. Studies of transactinide elements, including the synthesis of superheavy elements, nuclear structure far from stability, and RI-probed material science are planned with RI beams. An outlook of the transactinide nuclear chemistry studies using neutron-rich RI beams is described. (author)

  14. Interactions of relativistic heavy ions in thick heavy element targets and some unresolved problems

    Brandt, R.; Ditlov, V.A.; Pozharova, E.A.; Smirnitskij, V.A.

    2005-01-01

    Interactions of relativistic heavy ions with total energies above 30 GeV in thick Cu and Pb targets (≥2 cm) have been studied with various techniques. Radiochemical irradiation experiments using thick Cu targets, both in a compact form or as diluted '2π-Cu targets' have been carried out with several relativistic heavy ions, such as 44 GeV 12 C (JINR, Dubna) and 72 GeV 40 Ar (LBL, Berkeley, USA). Neutron measuring experiments using thick targets irradiated with various relativistic heavy ions up to 44 GeV 12 C have been performed at JINR. In addition, the number of 'black prongs' in nuclear interactions (due to protons with energies less than 30 MeV and emitted from the target-like interaction partner at rest) produced with 72 GeV 22 Ne ions in nuclear emulsion plates has been measured in the first nuclear interaction of the primary 22 Ne ion and in the following second nuclear interaction of the secondary heavy (Z>1) ion. Some essential results have been obtained. 1) Spallation products produced by relativistic secondary fragments in interactions ([44 GeV 12 C or 72 GeV 40 Ar]+Cu) within thick copper yield less products close to the target and much more products far away from the target as compared to primary beam interactions. This applies also to secondary particles emitted into large angles (Θ>10deg). 2) The neutron production of 44 GeV 12 C within thick Cu and Pb targets is beyond the estimated yield as based on experiments with 12 GeV 12 C. These rather independent experimental results cannot be understood with well-accepted nuclear reaction models. They appear to present unresolved problems

  15. Recent developments in the synthesis of super heavy elements

    Ackermann, D.

    2001-01-01

    Throughout the passed two decades isotopes of the elements with atomic numbers 107-112 have been synthesized and unambiguously identified at the velocity filter SHIP at GSI. In a recent experiment at SHIP the results for element 112 have been confirmed and a third decay chain of the isotope 277 112 has been observed. Cold fusion reactions using Pb- and Bi- targets and evaporation residue(ER)-α-α correlations together with an efficient separation and detection system are the major ingredients for the success of these experiments. The sensitivity limit of the set-up at GSI has reached the 1pb level. For a systematic investigation in this region of the chart of nuclei and to synthesize heavier nuclei this limit has to be pushed to even lower values. An extensive development program is pursued at SHIP in order to reach at least an order of magnitude lower cross sections. Systematic investigations, the construction of decay chain networks and mass measurements are some of the possible approaches to study the decay chains attributed to isotopes of the elements 114, 116 and 118 at Dubna and Berkeley, which are, in contrast to those observed at GSI, not connected to decays of known isotopes. For the Berkeley results, in particular, several trials of confirmation have been undertaken at various laboratories including GSI

  16. CORONAL SOURCES, ELEMENTAL FRACTIONATION, AND RELEASE MECHANISMS OF HEAVY ION DROPOUTS IN THE SOLAR WIND

    Weberg, Micah J. [PhD Candidate in Space Science, Department of Atmospheric, Oceanic, and Space Sciences, University of Michigan, 2134A Space Research Building, 2455 Hayward Street, Ann Arbor, MI 48109-2143, USA. (United States); Lepri, Susan T. [Associate Professor, Department of Atmospheric, Oceanic, and Space Sciences, University of Michigan, 2429 Space Research Building, 2455 Hayward Street, Ann Arbor, MI 48109-2143, USA. (United States); Zurbuchen, Thomas H., E-mail: mjweberg@umich.edu, E-mail: slepri@umich.edu, E-mail: thomasz@umich.edu [Professor, Space Science and Aerospace Engineering, Associate Dean for Entrepreneurship Senior Counselor of Entrepreneurship Education, Department of Atmospheric, Oceanic, and Space Sciences, University of Michigan, 2431 Space Research Building, 2455 Hayward Street, Ann Arbor, MI 48109-2143, USA. (United States)

    2015-03-10

    The elemental abundances of heavy ions (masses larger than He) in the solar wind provide information about physical processes occurring in the corona. Additionally, the charge state distributions of these heavy ions are sensitive to the temperature profiles of their respective source regions in the corona. Heavy ion dropouts are a relatively new class of solar wind events identified by both elemental and ionic charge state distributions. We have shown that their origins lie in large, closed coronal loops where processes such as gravitational settling dominate and can cause a mass-dependent fractionation pattern. In this study we consider and attempt to answer three fundamental questions concerning heavy ion dropouts: (1) 'where are the source loops located in the large-scale corona?'; (2) 'how does the interplay between coronal processes influence the end elemental abundances?'; and (3) 'what are the most probable release mechanisms'? We begin by analyzing the temporal and spatial variability of heavy ion dropouts and their correlation with heliospheric plasma and magnetic structures. Next we investigate the ordering of the elements inside dropouts with respect to mass, ionic charge state, and first ionization potential. Finally, we discuss these results in the context of the prevailing solar wind theories and the processes they posit that may be responsible for the release of coronal plasma into interplanetary space.

  17. Some new approaches to the synthesis of heavy and superheavy elements

    Flerov, G.N.

    1980-01-01

    The results of work on the synthesis of heavy and superheavy elements are considered. It is shown that the new regularity of the systematics of spontaneous-fission half-lives, established for heavy nuclei at Dubna, has made it possible to extend the region of the nuclei being synthesized. In particular, it becomes possible to produce relatively long-lived heavy isotopes of Z>=107. The results of experiments to study the emission of energetic α-particles in the collision of heavy nuclei are presented. It is noted that such reactions can be used to produce atomic nuclei with low excitation energy and large angular momentum. The possible use of similar reactions in the synthesis of heavy and superheavy elements is discussed. In case the existence of a naturally occurring superheavy element has been established, a possibility will arise to synthesize in nuclear reactions a number of isotopes belonging to the island of stability, and to investigate their properties. The present state of work on the search for superheavy elements in nature is briefly described

  18. CORONAL SOURCES, ELEMENTAL FRACTIONATION, AND RELEASE MECHANISMS OF HEAVY ION DROPOUTS IN THE SOLAR WIND

    Weberg, Micah J.; Lepri, Susan T.; Zurbuchen, Thomas H.

    2015-01-01

    The elemental abundances of heavy ions (masses larger than He) in the solar wind provide information about physical processes occurring in the corona. Additionally, the charge state distributions of these heavy ions are sensitive to the temperature profiles of their respective source regions in the corona. Heavy ion dropouts are a relatively new class of solar wind events identified by both elemental and ionic charge state distributions. We have shown that their origins lie in large, closed coronal loops where processes such as gravitational settling dominate and can cause a mass-dependent fractionation pattern. In this study we consider and attempt to answer three fundamental questions concerning heavy ion dropouts: (1) 'where are the source loops located in the large-scale corona?'; (2) 'how does the interplay between coronal processes influence the end elemental abundances?'; and (3) 'what are the most probable release mechanisms'? We begin by analyzing the temporal and spatial variability of heavy ion dropouts and their correlation with heliospheric plasma and magnetic structures. Next we investigate the ordering of the elements inside dropouts with respect to mass, ionic charge state, and first ionization potential. Finally, we discuss these results in the context of the prevailing solar wind theories and the processes they posit that may be responsible for the release of coronal plasma into interplanetary space

  19. What can we learn from the fission time of the super-heavy elements?

    Boilley, D.; Marchix, A.; Wilgenbus, D.; Lallouet, Y.; Gimbert, F.; Abe, Y.

    2007-01-01

    International audience; Recent experiments performed at GANIL with a crystal blocking technique have shown direct evidences of long fission times in the Super-Heavy Elements (SHE) region. Aimed to localize the SHE island of stability, can these experiments give access to the fission barrier and then to the shell-correction energy? In this paper, we calculate the fission time of heavy elements by using a new code, KEWPIE2, devoted to the study of the SHE.We also investigate the effect of poten...

  20. Magnetic spectrograph for the Holifield heavy ion research facility

    Ford, J.L.C. Jr.; Enge, H.A.; Erskine, J.R.; Hendrie, D.L.; LeVine, M.J.

    1977-01-01

    The need for a new generation magnetic spectrograph for the Holifield Heavy Ion Research Facility is discussed. The advantages of a magnetic spectrograph for heavy ion research are discussed, as well as some of the types of experiments for which such an instrument is suited. The limitations which the quality of the incident beam, target and spectrograph itself impose on high resolution heavy ion measurements are discussed. Desired features of an ideal new spectrograph are: (1) intrinsic resolving power E/ΔE greater than or equal to 3000; (2) maximum solid angle greater than or equal to 20 msr; (3) dispersion approx. 4-8m; (4) maximum energy interval approx. 30%; and (5) mass-energy product greater than or equal to 200. Various existing and proposed spectrographs are compared with the specifications for a new heavy ion magnet design

  1. Alpha decay properties of heavy and superheavy elements

    Vigila Bai, G.M. Carmel; Umai Parvathiy, J.

    2015-01-01

    Analysing accurately the lifetimes of α-decay chains is an important tool to detect and study the properties of superheavy nuclei. 48 Ca is used in the synthesis of superheavy nuclei Z = 106-118 at Dubna. The experimental work of 48 Ca projectiles at Dubna has given an opportunity to study the superheavy element (SHE). Here, the α-decay properties for Z = 106-118 are evaluated using our CYE model and are compared with the available experimental and theoretical values. (author)

  2. Recent Investigations of Heavy Elements (37≤Z≤92)

    Biemont, E.

    2011-01-01

    The present paper is an update and extension of previous compilations [1, 2] and it describes recent progress regarding the investigation of the radiative properties of the elements and ions (first three ionization stages) of the fifth and sixth rows of the periodic table and of the rare earths (mostly the lanthanides). From a combination of experimental radiative lifetimes obtained with laser spectroscopy and of theoretical branching fractions calculated with a quasirelativistic Hartree-Fock approach taking configuration interaction and core-polarization effects into account, transition probabilities have been deduced for a large number of transitions of astrophysical interest. Some new results are briefly described here. The numerical values are stored in the databases DESIRE and DREAM, which are developped and progressively updated on a web site of Mons University in Belgium.

  3. Progress in heavy ion fusion research

    Celata, C.M.; Bieniosek, F.M.; Henestroza, E.; Kwan, J.W.; Lee, E.P.; Logan, G.; Prost, L.; Seidl, P.A.; Vay, J.-L.; Waldron, W.L.; Yu, S.S.; Barnard, J.J.; Callahan, D.A.; Cohen, R.H.; Friedman, A.; Grote, D.P.; Lund, S.M.; Molvik, A.; Sharp, W.M.; Westenskow, G.

    2003-01-01

    The U.S. Heavy Ion Fusion program has recently commissioned several new experiments. In the High Current Experiment [P. A. Seidl et al., Laser Part. Beams 20, 435 (2003)], a single low-energy beam with driver-scale charge-per-unit-length and space-charge potential is being used to study the limits to transportable current posed by nonlinear fields and secondary atoms, ions, and electrons. The Neutralized Transport Experiment similarly employs a low-energy beam with driver-scale perveance to study final focus of high perveance beams and neutralization for transport in the target chamber. Other scaled experiments--the University of Maryland Electron Ring [P. G. O'Shea et al., accepted for publication in Laser Part. Beams] and the Paul Trap Simulator Experiment [R. C. Davidson, H. Qin, and G. Shvets, Phys. Plasmas 7, 1020 (2000)]--will provide fundamental physics results on processes with longer scale lengths. An experiment to test a new injector concept is also in the design stage. This paper will describe the goals and status of these experiments, as well as progress in theory and simulation. A proposed future proof-of-principle experiment, the Integrated Beam Experiment, will also be described

  4. Survival and compound nucleus probability of super heavy element Z = 117

    Manjunatha, H.C. [Government College for Women, Department of Physics, Kolar, Karnataka (India); Sridhar, K.N. [Government First grade College, Department of Physics, Kolar, Karnataka (India)

    2017-05-15

    As a part of a systematic study for predicting the most suitable projectile-target combinations for heavy-ion fusion experiments in the synthesis of {sup 289-297}Ts, we have calculated the transmission probability (T{sub l}), compound nucleus formation probabilities (P{sub CN}) and survival probability (P{sub sur}) of possible projectile-target combinations. We have also studied the fusion cross section, survival cross section and fission cross sections for different projectile-target combination of {sup 289-297}Ts. These theoretical parameters are required before the synthesis of the super heavy element. The calculated probabilities and cross sections show that the production of isotopes of the super heavy element with Z = 117 is strongly dependent on the reaction systems. The most probable reactions to synthetize the super heavy nuclei {sup 289-297}Ts are worked out and listed explicitly. We have also studied the variation of P{sub CN} and P{sub sur} with the mass number of projectile and target nuclei. This work is useful in the synthesis of the super heavy element Z = 117. (orig.)

  5. Survival and compound nucleus probability of super heavy element Z = 117

    Manjunatha, H.C.; Sridhar, K.N.

    2017-01-01

    As a part of a systematic study for predicting the most suitable projectile-target combinations for heavy-ion fusion experiments in the synthesis of "2"8"9"-"2"9"7Ts, we have calculated the transmission probability (T_l), compound nucleus formation probabilities (P_C_N) and survival probability (P_s_u_r) of possible projectile-target combinations. We have also studied the fusion cross section, survival cross section and fission cross sections for different projectile-target combination of "2"8"9"-"2"9"7Ts. These theoretical parameters are required before the synthesis of the super heavy element. The calculated probabilities and cross sections show that the production of isotopes of the super heavy element with Z = 117 is strongly dependent on the reaction systems. The most probable reactions to synthetize the super heavy nuclei "2"8"9"-"2"9"7Ts are worked out and listed explicitly. We have also studied the variation of P_C_N and P_s_u_r with the mass number of projectile and target nuclei. This work is useful in the synthesis of the super heavy element Z = 117. (orig.)

  6. Exploration of (super-)heavy elements using the Skyrme-Hartree-Fock model

    Erler, Jochen

    2011-01-01

    Motivated by the steadily increasing number of known nuclei and nuclear properties, theories of nuclear structure are presently a field of intense research. This work concentrates on the self-consistent description of nuclei in terms of the Skyrme-Hartree-Fock (SHF) approach. The extrapolation of nuclear shell structure to the region of super-heavy elements (SHE) using the SHF model, the dependence on different parameterization and the influence of collective correlation will be studied. The general scope of this work are large scale calculation for a global survey of properties of SHE like binding energies, separation energies and decay characteristics and lifetimes. These calculations were done in a collaboration with the theory group of the GSI in Darmstadt and have the aim to develop a database of lifetimes and reaction rates for α, β-decay and spontaneous fission in a very wide range with proton numbers 86 ≤ Z ≤ 120 and neutron numbers up to N ∼ 260 relevant for the astrophysical r-process. The results of this study for example predictions of a possible islands of very stable nuclei and information of favored decay mode for each nuclei are also applicable in the recent experimental synthesis of exotic SHE. For these calculation a framework to calculate β-decay half-lives within the SHF model has been developed and the existing axial SHF code has been extended to compute β-transition matrix elements and so to provide an estimation of half-lives. (orig.)

  7. Exploration of (super-)heavy elements using the Skyrme-Hartree-Fock model

    Erler, Jochen

    2011-01-31

    Motivated by the steadily increasing number of known nuclei and nuclear properties, theories of nuclear structure are presently a field of intense research. This work concentrates on the self-consistent description of nuclei in terms of the Skyrme-Hartree-Fock (SHF) approach. The extrapolation of nuclear shell structure to the region of super-heavy elements (SHE) using the SHF model, the dependence on different parameterization and the influence of collective correlation will be studied. The general scope of this work are large scale calculation for a global survey of properties of SHE like binding energies, separation energies and decay characteristics and lifetimes. These calculations were done in a collaboration with the theory group of the GSI in Darmstadt and have the aim to develop a database of lifetimes and reaction rates for {alpha}, {beta}-decay and spontaneous fission in a very wide range with proton numbers 86 {<=} Z {<=} 120 and neutron numbers up to N {approx} 260 relevant for the astrophysical r-process. The results of this study for example predictions of a possible islands of very stable nuclei and information of favored decay mode for each nuclei are also applicable in the recent experimental synthesis of exotic SHE. For these calculation a framework to calculate {beta}-decay half-lives within the SHF model has been developed and the existing axial SHF code has been extended to compute {beta}-transition matrix elements and so to provide an estimation of half-lives. (orig.)

  8. Exploration of new biological specific function by heavy elements stimulus

    Macaskie, Lynne; Renshaw, Joanna; Ohnuki, Toshihiko; Nishiguchi, Norihiko; Utsunomiya, Satoshi; Suzuki, Yoshinori; Shirai, Osamu

    2014-01-01

    We have carried out experiments to investigate bio-mineralization of rare earth elements (REE) on the cell surface of yeast Saccharomyces cerevisiae, and the bacteria Bacillus subtilis, Pseudomonas fluorescens and Serratia sp. The continuous removal of 1 mM La (100%) Nd (100%) and Eu (>80%) was observed using a continuous flow through immobilized Serratia sp cell columns. Chemical and physical characterization of bio-mineralized La and Eu was done by XRD at Birmingham and showed the formation of phosphate minerals. Additional cell column work using S. cerevisiae, B. subtilis, or P. fluorescens, showed that these bacteria are capable of bio-mineralizing Ce(III) and Sm(III). Chemical and physical characterizations of bio-transformed Ce and Sm were analyzed by JAEA, Kyushu U., Tokyo U. Tech. and Kyoto U. using XAFS, SEM and TEM. Results showed that Ce and Sm nanoparticles were formed. The high radiostability of the metal accumulating enzyme of Serratia sp. (which promotes metal phosphate deposition) was shown in whole cells, whereas pure enzyme lost its activity quickly under irradiation. Additional work on radionuclide (Cm) incorporation into Serratia sp calcium phosphate minerals (analogue for human bones) using EXAFS and Time Resolved Laser Fluorescence Spectroscopy (in collaboration with Karlsruhe Institute of Technology) showed that this actinide binds at the grain boundaries between crystallites, which has health implications for human exposure. (author)

  9. Exploration of new biological specific function by heavy elements stimulus

    Macaskie, Lynne; Renshaw, Joanna; Ohnuki, Toshihiko; Nishiguchi, Norihiko; Utsunomiya, Satoshi; Suzuki, Yoshinori; Shirai, Osamu

    2012-01-01

    We have carried out experiments to investigate bio-mineralization of rare earth elements (REE) on the cell surface of yeast Saccharomyces cerevisiae, and the bacteria Bacillus subtilis, Pseudomonas fluorescens and Serratia sp. The continuous removal of 1 mM La (100%) Nd (100%) and Eu(>80%) was observed using a continuous flow through immobilized Serratia sp cell columns. Chemical and physical characterization of bio-mineralized La and Eu was done by XRD at Birmingham and showed the formation of phosphate minerals. Additional cell column work using S. cerevisiae, B. subtilis, or P. fluorescens, showed that these bacteria are capable of bio-mineralizing Ce(III) and Sm(III). Chemical and physical characterizations of bio-transformed Ce and Sm were analyzed by JAEA, Kyushu U., Tokyo U. Tech. and Kyoto U. using XAFS, SEM and TEM. Results showed that Ce and Sm nanoparticles were formed. The high radiostability of the metal accumulating enzyme of Serratia sp. (which promotes metal phosphate deposition) was shown in whole cells, whereas pure enzyme lost its activity quickly under irradiation. Additional work on radionuclide (Cm) incorporation into Serratia sp calcium phosphate minerals (analogue for human bones) using EXAFS and Time Resolved Laser Fluorescence Spectroscopy (in collaboration with Karlsruhe Institute of Technology) showed that this actinide binds at the grain boundaries between crystallites, which has health implications for human exposure. (author)

  10. Signatures of Heavy Element Production in Neutron Star Mergers

    Barnes, Jennifer

    2018-06-01

    Compact object mergers involving at least one neutron star have long been theorized to be sites of astrophysical nucleosynthesis via rapid neutron capture (the r-process). The observation in light and gravitational waves of the first neutron star merger (GW1701817) this past summer provided a stunning confirmation of this theory. Electromagnetic emission powered by the radioactive decay of freshly synthesized nuclei from mergers encodes information about the composition burned by the r-process, including whether a particular merger event synthesized the heaviest nuclei along the r-process path, or froze out at lower mass number. However, efforts to model the emission in detail must still contend with many uncertainties. For instance, the uncertain nuclear masses far from the valley of stability influence the final composition burned by the r-process, as will weak interactions operating in the merger’s immediate aftermath. This in turn can affect the color electromagnetic emission. Understanding the details of these transients’ spectra will also require a detailed accounting the electronic transitions of r-process elements and ions, in order to identify the strong transitions that underlie spectral formation. This talk will provide an overview of our current understanding of radioactive transients from mergers, with an emphasis on the role of experiment in providing critical inputs for models and reducing uncertainty.

  11. Physicochemical, heavy metal and mineral elements assessment of ...

    The Benin-Agbor road is a major road linking Edo State and the Eastern states of Nigeria, characterized by daily vehicular movements. The inhabitants of the area depend on the river waters mainly for their domestic purposes. It was against the above background that this research was conducted in order to assess the ...

  12. Molecular orbital studies of the bonding in heavy element organometallics

    Bursten, B.E.

    1990-01-01

    This progress report contains highlights of research projects in actinide chemistry. Projects covered are bonding in Np, Pu, and transplutonium organometallic compounds, applications of the discrete variational Xα method to actinide chemistry, ab initio calculations on actinide molecules, and experimental comparisons of organoactinide and organotransition metal chemistry. Also included is brief discussions on budgets, funding, invited papers and invited presentations. (JL)

  13. X-ray Ionization of Heavy Elements Applied to Protoplanetary Disks

    Ádámkovics, Máté; Glassgold, Alfred E.; Meijerink, Rowin

    The consequences of the Auger effect on the population of heavy-element ions are analyzed for the case of relatively cool gas irradiated by keV X-rays with intended applications to the accretion disks of young stellar objects. Highly charged ions are rapidly reduced to the doubly charged state in

  14. Heavy-Ion Fusion Mechanism and Predictions of Super-Heavy Elements Production

    Abe, Yasuhisa; Shen Caiwan; Boilley, David; Giraud, Bertrand G.; Kosenko, Grigory

    2009-01-01

    Fusion process is shown to firstly form largely deformed mono-nucleus and then to undergo diffusion in two-dimensions with the radial and mass-asymmetry degrees of freedom. Examples of prediction of residue cross sections are given for the elements with Z = 117 and 118.

  15. Holifield Heavy-Ion Research Facility at Oak Ridge

    Jones, C.M.

    1977-01-01

    A new heavy-ion accelerator facility is now under construction at the Oak Ridge National Laboratory. A brief description of the scope and schedule of this project is given, and the new large tandem accelerator, which will be a major element of the facility is discussed in some detail. Several studies which have been made or are in progress in Oak Ridge in preparation for operation of the tandem accelerator are briefly described

  16. New Fragment Separation Technology for Superheavy Element Research

    Shaughnessy, D A; Moody, K J; Henderson, R A; Kenneally, J M; Landrum, J H; Lougheed, R W; Patin, J B; Stoyer, M A; Stoyer, N J; Wild, J F; Wilk, P A

    2008-01-01

    This project consisted of three major research areas: (1) development of a solid Pu ceramic target for the MASHA separator, (2) chemical separation of nuclear decay products, and (3) production of new isotopes and elements through nuclear reactions. There have been 16 publications as a result of this project, and this collection of papers summarizes our accomplishments in each of the three areas of research listed above. The MASHA (Mass Analyzer for Super-Heavy Atoms) separator is being constructed at the U400 Cyclotron at the Flerov Laboratory of Nuclear Reactions in Dubna, Russia. The purpose of the separator is to physically separate the products from nuclear reactions based on their isotopic masses rather than their decay characteristics. The separator was designed to have a separation between isotopic masses of ±0.25 amu, which would enable the mass of element 114 isotopes to be measured with outstanding resolution, thereby confirming their discovery. In order to increase the production rate of element 114 nuclides produced via the 244 Pu+ 48 Ca reaction, a new target technology was required. Instead of a traditional thin actinide target, the MASHA separator required a thick, ceramic-based Pu target that was thick enough to increase element 114 production while still being porous enough to allow reaction products to migrate out of the target and travel through the separator to the detector array located at the back end. In collaboration with UNLV, we began work on development of the Pu target for MASHA. Using waste-form synthesis technology, we began by creating zirconia-based matrices that would form a ceramic with plutonium oxide. We used samarium oxide as a surrogate for Pu and created ceramics that had varying amounts of the starting materials in order to establish trends in material density and porosity. The results from this work are described in more detail in Refs. [1,4,10]. Unfortunately, work on MASHA was delayed in Russia because it was found that

  17. Elements-admixtures of fluorite. Research technique

    Fayziev, A.R.

    2002-01-01

    Present article is devoted to elements-admixtures of fluorite and research techniques used. As a material for researches the mono mineral samples of fluorite of various geologic deposits and ores were used. The determination of sodium and potassium was conducted by means of flame photometry. Strontium, uranium, thorium, lead and rubidium were determined by means of quantitative X-ray spectroscopic analysis. The barium analysis was conducted by means of quantitative method. The manganese analysis was conducted by means of electron paramagnetic resonance.

  18. Research on heavy metal pollution of river Ganga: A review

    Dipak Paul

    2017-06-01

    Full Text Available River Ganga is considered sacred by people of India for providing life sustenance to environment and ecology. Anthropogenic activities have generated important transformations in aquatic environments during the last few decades. Advancement of human civilization has put serious questions to the safe use of river water for drinking and other purposes. The river water pollution due to heavy metals is one of the major concerns in most of the metropolitan cities of developing countries. These toxic heavy metals entering the environment may lead to bioaccumulation and biomagnifications. These heavy metals are not readily degradable in nature and accumulate in the animal as well as human bodies to a very high toxic amount leading to undesirable effects beyond a certain limit. Heavy metals in riverine environment represent an abiding threat to human health. Exposure to heavy metals has been linked to developmental retardation, kidney damage, various cancers, and even death in instances of very high exposure. The following review article presents the findings of the work carried out by the various researchers in the past on the heavy metal pollution of river Ganga.

  19. Matrix elements of Δ B =0 operators in heavy hadron chiral perturbation theory

    Lee, Jong-Wan

    2015-05-01

    We study the light-quark mass and spatial volume dependence of the matrix elements of Δ B =0 four-quark operators relevant for the determination of Vu b and the lifetime ratios of single-b hadrons. To this end, one-loop diagrams are computed in the framework of heavy hadron chiral perturbation theory with partially quenched formalism for three light-quark flavors in the isospin limit; flavor-connected and -disconnected diagrams are carefully analyzed. These calculations include the leading light-quark flavor and heavy-quark spin symmetry breaking effects in the heavy hadron spectrum. Our results can be used in the chiral extrapolation of lattice calculations of the matrix elements to the physical light-quark masses and to infinite volume. To provide insight on such chiral extrapolation, we evaluate the one-loop contributions to the matrix elements containing external Bd, Bs mesons and Λb baryon in the QCD limit, where sea and valence quark masses become equal. In particular, we find that the matrix elements of the λ3 flavor-octet operators with an external Bd meson receive the contributions solely from connected diagrams in which current lattice techniques are capable of precise determination of the matrix elements. Finite volume effects are at most a few percent for typical lattice sizes and pion masses.

  20. Superheavy element research at the velocity filter ship

    Heinz, S.

    2012-01-01

    The Separator for Heavy Ion Reaction Products (SHIP) is a velocity filter located at the UNILAC accelerator of GSI Darmstadt, Germany. For about 35 years a broad experimental program in the field of superheavy element research is running at SHIP. During the last years particularly investigations in the region of the heaviest known nuclei were performed. In fusion reactions of 48 Ca + 248 Cm → 296 116* a total of six decay chains was observed which could be attributed to the evaporation residues 292 116 and 293 116. In this experiment, data measured previously on the same isotopes in Dubna were well confirmed. Besides, two attempts were made to synthesize isotopes of the still unobserved element Z = 120 in reactions of 64 Ni + 238 U and 54 Cr + 248 Cm. No events were observed in these experiments leading to one-event cross-section limits of 90 fb and 560 fb, respectively. For future superheavy element research, a new superconducting continuous wave LINAC is planned at GSI which shall deliver beam intensities of up to 1014 particles per second. In this context we are developing a next generation separator and new detection techniques

  1. High-energy elastic recoil detection heavy ions for light element analysis

    Goppelt-Langer, P.; Yamamoto, S.; Takeshita, H.; Aoki, Y.; Naramoto, H.

    1994-01-01

    The detection of light and medium heavy elements in not homogeneous solids is a severe problem in ion beam analysis. Heavy elements can be detected by the well established Rutherford backscattering technique (RBS). In a homogeneous host material most impurities can be easily analyzed by secondary ion mass spectroscopy (SIMS). Some isotopes ( 3 He, 6 Li, 10 B) can be measured by nuclear reaction analysis (NRA) using thermal neutrons inducing (n, p) or (n, α) reactions. Others can be detected by energetic ion beams by nuclear reactions (e.g. 15 N( 1 H, αγ) 12 C for analysis of hydrogen). A high content of H, D or T can be also determined by elastic recoil detection using an energetic He beam. The latter technique has been developed to a universal method for detection of light and heavy elements in any target, using a high energetic heavy ion beam and a detector system, which is able to identify the recoils and delivers energy and position of the particles. (author)

  2. [Heavy ion physics research at Creighton University

    Cherney, M.

    1992-01-01

    This research continues the baseline efforts i n the investigation of the behavior of hadronic matter under extreme conditions. The project is concerned with the search for indications of a phase transition from hadronic to quark matter in the STAR, NA44 and NA36 experiments. It is believed that the conditions. This project contributes to the development of a slow control system and time projection chamber tracking for the STAR experiment, upgrades for the NA44 experiment at CERN through studies of a spot focusing Cherenkov-detector, and the remaining analysis of data collected with the NA36 experiment at CERN.

  3. [Heavy ion physics research at Creighton University

    Cherney, M.

    1992-01-01

    This research continues the baseline efforts i n the investigation of the behavior of hadronic matter under extreme conditions. The project is concerned with the search for indications of a phase transition from hadronic to quark matter in the STAR, NA44 and NA36 experiments. It is believed that the conditions. This project contributes to the development of a slow control system and time projection chamber tracking for the STAR experiment, upgrades for the NA44 experiment at CERN through studies of a spot focusing Cherenkov-detector, and the remaining analysis of data collected with the NA36 experiment at CERN

  4. The Distribution of Heavy Element From Fish, Algae, Water and Sea Sediment In Lemahabang Muria Peninsula

    Sukirno; J-Djati-Pramana; Sumining

    2005-01-01

    The analysis of heavy elements from fish, algae, water and sea sediments in Muria peninsula Jepara has been carried out using neutron activation analysis (NAA) method. Irradiation of sample was carried out for twelve hours with using Lazy Susan facility with neutron flux of 0.585x10 11 n.cm -2 .S -1 . Comparative mode of measurement was used for avoiding the effects of neutron flux parameters on the results. The result on analysis using gamma spectrometry with a Ge(Li) detector showed that there were 6 elements which observed. Those elements contained in algae, fish, water and sea sediment were Co, Sb, Sc, Fe, Cr and Cd. The highest element concentration found in sediment was Fe of 65.625 ± 3.12 % and the lowest was Co of 0.00256 ± 0.00045 μg/g for sea water. This method give precision and relative accuracy of < 10 % for all elements. (author)

  5. New heavy-ion-fusion accelerator research program

    Herrmannsfeldt, W.B.

    1983-05-01

    This paper will briefly summarize the concepts of Heavy Ion Fusion (HIF), especially those aspects that are important to its potential for generating electrical power. It will also note highlights of the various HIF programs throughout the world. Especially significant is that the US Department of Energy (DOE) plans a program, beginning in 1984, aimed at determining the feasibility of using heavy ion accelerators as drivers for Inertial Confinement Fusion (ICF). The new program concentrates on the aspects of accelerator design that are important to ICF, and for this reason is called HIF Accelerator Research

  6. Application of alpha spectrometry to the discovery of new elements by heavy-ion-beam bombardment

    Nitschke, J.M.

    1983-05-01

    Starting with polonium in 1898, α-spectrometry has played a decisive role in the discovery of new, heavy elements. For even-even nuclei, α-spectra have proved simple to interpret and exhibit systematic trends that allow extrapolation to unknown isotopes. The early discovery of the natural α-decay series led to the very powerful method of genetically linking the decay of new elements to the well-established α-emission of daughter and granddaughter nuclei. This technique has been used for all recent discoveries of new elements including Z = 109. Up to mendelevium (Z = 101), thin samples suitable for α-spectrometry were prepared by chemical methods. With the advent of heavy-ion accelerators new sample preparation methods emerged. These were based on the large momentum transfer associated with heavy-ion reactions, which produced energetic target recoils that, when ejected from the target, could be thermalized in He gas. Subsequent electrical deposition or a He-jet technique yielded samples that were not only thin enough for α-spectroscopy, but also for α- and #betta#-recoil experiments. Many variations of these methods have been developed and are discussed. For the synthesis of element 106 an aerosol-based recoil transport technique was devised. In the most recent experiments, α-spectrometry has been coupled with the magnetic analysis of the recoils. The time from production to analysis of an isotope has thereby been reduced to 10 - 6 s; while it was 10 - 1 to 10 0 s for He-jets and 10 1 to 10 3 s for rapid chemical separations. Experiments are now in progress to synthesize super heavy elements (SHE) and to analyze them with these latest techniques. Again, α-spectrometry will play a major role since the expected signature for the decay of a SHE is a sequence of α-decays followed by spontaneous fission

  7. Heavy Ion Fusion Accelerator Research (HIFAR) year-end report, April 1, 1990--September 30, 1990

    1990-12-01

    The basic objective of the Heavy Ion Fusion Accelerator Research (HIFAR) program is to assess the suitability of heavy ion accelerators as igniters for Inertial Confinement Fusion (ICF). A specific accelerator technology, induction acceleration, is being studied at the Lawrence Berkeley Laboratory and at the Lawrence Livermore National Laboratory. The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the validation of new accelerator strategies to cut costs. Key elements to be addressed include: (1) beam quality limits set by transverse and longitudinal beam physics; (2) development of induction accelerating modules, and multiple-beam hardware, at affordable costs; (3) acceleration of multiple beams with current amplification without significant dilution of the optical quality of the beams; (4) final bunching, transport, and accurate focusing on a small target

  8. Heavy Ion Fusion Accelerator Research (HIFAR) year-end report, April 1--September 30, 1988

    1988-12-01

    The basic objective of the Heavy Ion Fusion Accelerator Research (HIFAR) program is to assess the suitability of heavy ion accelerators as igniters for Inertial Confinement Fusion (ICF). A specific accelerator technology, the induction linac, has been studied at the Lawrence Berkeley Laboratory and has reached the point at which its viability for ICF applications can be assessed over the next few years. The HIFAR program addresses the generation of high power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the validation of new accelerator strategies, to cut costs. Key elements to be addressed include: beam quality limits set by transverse and longitudinal beam physics; development of induction accelerating modules, and multiple-beam hardware, at affordable costs; acceleration of multiple beams with current amplification --both new features in a linac -- without significant dilution of the optical quality of the beams; final bunching, transport, and accurate focusing on a small target

  9. Heavy Ion Fusion Accelerator Research (HIFAR) year-end report, October 1, 1987--March 31, 1988

    1988-06-01

    The basic objective of the Heavy Ion Fusion Accelerator Research (HIFAR) program is to assess the suitability of heavy ion accelerators as igniters for Inertial Confinement Fusion (ICF). A specific accelerator technology, the induction linac, has been studied at Lawrence Berkeley Laboratory and has reached the point at which its viability for ICF applications can be assessed over the next few years. The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the validation of new accelerator strategies, to cut costs. Key elements to be addressed include: beam quality limits set by transverse and longitudinal beam physics; development of induction accelerating modules, and multiple-beam hardware, at affordable costs; acceleration of multiple beams with current amplification -- both new features in a linac -- without significant dilution of the optical quality of beams; and final bunching, transport, and accurate focusing on a small target

  10. Effect of γ-ray emission on transuranium element production cross sections in heavy ion reactions

    Il'inov, A.S.; Oganesyan, Yu.Ts.; Cherepanov, E.A.

    1980-01-01

    The effect of competition of the γ ray emission with neutron evaporation and of compound nuclei fission induced by heavy ion reactions on the production cross sections for transuranium elements is considered. It is shown that taking account of γ ray emission leads to the broadening of the excitation functions of the (HI, xny) reactions such as 18 O+ 238 U, 40 Ar+ 206 Pb, 40 Ar+ 207 Pb and 40 Ar+ 208 Pb reactions and to the displacement of their maximum toward the higher energies as well as to an increase of the absolute cross sections which is especially strong close to the fusion barrier. Cross sections for the radiative capture of heavy ions by a heavy target nucleus in 40 Ar+ 206 Pb, 40 Ar+ 208 Pb, 48 Ca+ 204 Pb and 48 Ca+ 208 Pb reactions are estimated

  11. A novel approach to the island of stability of super-heavy elements search

    Wieloch A.

    2016-01-01

    Full Text Available It is expected that the cross section for super-heavy nuclei production of Z > 118 is dropping into the region of tens of femto barns. This creates a serious limitation for the complete fusion technique that is used so far. Moreover, the available combinations of the neutron to proton ratio of stable projectiles and targets are quite limited and it can be difficult to reach the island of stability of super heavy elements using complete fusion reactions with stable projectiles. In this context, a new experimental investigation of mechanisms other than complete fusion of heavy nuclei and a novel experimental technique are invented for our search of super- and hyper-nuclei. This contribution is focused on that technique.

  12. New approach to description of fusion-fission dynamics in super-heavy element formation

    Zagrebaev, V.I.

    2002-01-01

    A new mechanism of the fusion-fission process for a heavy nuclear system is proposed, which takes place in the (A 1 , A 2 ) space, where A 1 and A 2 are two nuclei, surrounded by a certain number of shared nucleons ΔA. The nuclei A 1 and A 2 gradually lose (or acquire) their individualities with increasing (or decreasing) a number of collectivized nucleons ΔA. The driving potential in the (A 1 , A 2 ) space is derived, which allows the calculation of both the probability of the compound nucleus formation and the mass distribution of fission and quasi-fission fragments in heavy ion fusion reactions. The cross sections of super-heavy element formation in the 'hot' and 'cold' fusion reactions have been calculated up to Z CN =118. (author)

  13. PROBABILISTIC FINITE ELEMENT ANALYSIS OF A HEAVY DUTY RADIATOR UNDER INTERNAL PRESSURE LOADING

    ROBIN ROY P.

    2017-09-01

    Full Text Available Engine cooling is vital in keeping the engine at most efficient temperature for the different vehicle speed and operating road conditions. Radiator is one of the key components in the heavy duty engine cooling system. Heavy duty radiator is subjected to various kinds of loading such as pressure, thermal, vibration, internal erosion, external corrosion, creep. Pressure cycle durability is one of the most important characteristic in the design of heavy duty radiator. Current design methodologies involve design of heavy duty radiator using the nominal finite element approach which does not take into account of the variations occurring in the geometry, material and boundary condition, leading to over conservative and uneconomical designs of radiator system. A new approach is presented in the paper to integrate traditional linear finite element method and probabilistic approach to design a heavy duty radiator by including the uncertainty in the computational model. As a first step, nominal run is performed with input design variables and desired responses are extracted. A probabilistic finite elementanalysis is performed to identify the robust designs and validated for reliability. Probabilistic finite element includes the uncertainty of the material thickness, dimensional and geometrical variation. Gaussian distribution is employed to define the random variation and uncertainty. Monte Carlo method is used to generate the random design points.Output response distributions of the random design points are post-processed using different statistical and probability technique to find the robust design. The above approach of systematic virtual modelling and analysis of the data helps to find efficient and reliable robust design.

  14. Simulation studies of acceleration of heavy ions and their elemental compositions

    Toida, Mieko; Ohsawa, Yukiharu

    1996-07-01

    By using a one-dimensional, electromagnetic particle simulation code with full ion and electron dynamics, we have studied the acceleration of heavy ions by a nonlinear magnetosonic wave in a multi-ion-species plasma. First, we describe the mechanism of heavy ion acceleration by magnetosonic waves. We then investigate this by particle simulations. The simulation plasma contains four ion species: H, He, O, and Fe. The number density of He is taken to be 10% of that of H, and those of O and Fe are much lower. Simulations confirm that, as in a single-ion-species plasma, some of the hydrogens can be accelerated by the longitudinal electric field formed in the wave. Furthermore, they show that magnetosonic waves can accelerate all the particles of all the heavy species (He, O, and Fe) by a different mechanism, i.e., by the transverse electric field. The maximum speeds of the heavy species are about the same, of the order of the wave propagation speed. These are in good agreement with theoretical prediction. These results indicate that, if high-energy ions are produced in the solar corona through these mechanisms, the elemental compositions of these heavy ions can be similar to that of the background plasma, i.e., the corona

  15. Relative radiative decay rates of vacancies in L-subshells of heavy elements

    Barros Leite, C.V. de; Pinho, A.G. de; Castro Faria, N.V. de.

    1977-01-01

    Relative radiative decay of vacancies in L-subshells were measured for a large number of heavy elements with a Si(Li) detection system. A graphical method was employed to analyze the x-ray spectra so obtained. Systematic results are presented together with other already published results obtained in our laboratories in recent years. This covers the interval 74<=Z<=93. Results are compared with theoretical predictions and experimental data from other authors and some general features are noted

  16. Long-lived heavy mass elements half-lives (A > 125)

    Holden, N.E.

    1985-01-01

    Reported values of half-lives of intermediate mass and heavy elements are evaluated. The evaluation analysis estimates the systematic error the resulting standard deviation. Recommended values are then presented for 128 Te, 130 Te, 129 I, 138 La, 144 Nd, 145 Nd, /sup 146,147,148/Sm, 152 Gd, 154 Dy, 176 Lu, 174 Hf, 180 Ta, 187 Re, 186 Os, 190 Pt, /sup 204,205/Pb, and /sup 230,232/Th. 103 refs., 21 tabs

  17. Heavy-ion accelerator research for inertial fusion

    1987-08-01

    Thermonuclear fusion offers a most attractive long-term solution to the problem of future energy supplies: The fuel is virtually inexhaustible and the fusion reaction is notably free of long-lived radioactive by-products. Also, because the fuel is in the form of a plasma, there is no solid fuel core that could melt down. The DOE supports two major fusion research programs to exploit these virtues, one based on magnetic confinement and a second on inertial confinement. One part of the program aimed at inertial fusion is known as Heavy Ion Fusion Accelerator Research, or HIFAR. In this booklet, the aim is to place this effort in the context of fusion research generally, to review the brief history of heavy-ion fusion, and to describe the current status of the HIFAR program

  18. Study of the Matrix Effect on the Plasma Characterization of Heavy Elements in Soil Sediments

    Tawfik W.

    2007-01-01

    Full Text Available Laser-induced breakdown spectroscopy (LIBS has been applied to perform a study of the matrix effect on the plasma characterization of soil sediment targets. The plasma is generated by focusing a pulsed Nd: YAG laser on the target in air at atmospheric pressure. The plasma emission spectrum was detected using a portable Echelle spectrometer (Mechelle 7500 — Multichannel Instruments, Stockholm, Sweden with intensified CCD camera. Spectroscopic analysis of plasma evolution of laser produced plasmas has been characterized in terms of their spectra, and electron temperature. Four heavy elements V, Pb, Mn and Co were determined in the obtained spectra. The LTE and optically thin plasma conditions were verified for the produced plasma. The electron temperature and density were determined using the emission intensity and stark broadening, respectively, of the spectral lines of the heavy elements in the soil sediments. The electron temperature does not change with concentration. For environmental applications, the obtained results showed the capability of the proposed LIBS setup with the portable Mechelle 7500 spectrometer to be applied in-situ for real-time measurements of the variation of the matrix elemental composition of soil sediments by following up only a single element as a marker for the composition of the soil sediment without need of analysis of the other elements.

  19. HAIR HEAVY METAL AND ESSENTIAL TRACE ELEMENT CONCENTRATION IN CHILDREN WITH AUTISM SPECTRUM DISORDER.

    Tabatadze, T; Zhorzholiani, L; Kherkheulidze, M; Kandelaki, E; Ivanashvili, T

    2015-11-01

    Our study aims evaluation of level of essential trace elements and heavy metals in the hair samples of children with autistic spectrum disorder (ASD) and identification of changes that are associated with autistic spectrum disorders. Case-control study was conducted at Child Development Center of Iashvili Children's Central Hospital (LD).We studied 60 children aged from 4 to 5 years old. The concentrations of 28 elements among (Ca,Zn, K, Fe, Cu, Se, Mn, Cr, S, Br, Cl, Co, Ag, V, Ni, Rb, Mo, Sr, Ti, Ba, Pb, As, Hg, Cd, Sb, Zr, Sn, Bi) them trace elements and toxic metals) were determined in scalp hair samples of children (n=30) with autistic spectrum disorder (ASD) and from control group of healthy children (n=30) with matched sex and age. Micro-elemental status was detected in the hair, with roentgen-fluorescence spectrometer method (Method MBИ 081/12-4502-000, Apparatus ALVAX- CIP, USA - UKRAIN) .To achieve the similarity of study and control groups, pre and postnatal as well as family and social history were assessed and similar groups were selected. Children with genetic problems, malnourished children, children from families with social problems were excluded from the study. The diagnosis of ASD were performed by pediatrician and psychologist (using M-CHAT and ADOS) according to DSM IV (Diagnostic and Statistical Manual of Mental Disorders from the American Psychiatric association) criteria. The study was statistically analyzed using computer program SPSS 19. Deficiencies of essential trace microelements revealed in both group, but there was significant difference between control and studied groups. The most deficient element was zinc (92% in target and 20% in control), then - manganese (55% and 8%) and selenium (38% and 4%). In case of cooper study revealed excess concentration of this element only in target group in 50% of cases. The contaminations to heavy metals were detected in case of lead (78% and 16), mercury (43% and 10%) and cadmium (38% and 8%). The

  20. Empirical description of the element production cross sections in dissipative heavy-ion collisions

    Wollersheim, H.J.

    1984-06-01

    Correlations between experimental observables yield analytical expressions for the energy dsigma/dE and element distributions dsigma/dZ, d 2 sigma/dZdE in dissipative collisions. These empirical formulas are applied to twelve heavy ion systems at bombarding energies well above the Coulomb barrier. The element production can be calculated for all kinetic energies of the reaction fragments from the quasi-elastic region down to a minimum total kinetic energy Vsub(c)sup(def) which is the result of the Coulomb repulsion of two deformed nuclei prior to scission. In cases where the dissipative collisions are the dominant part of the reaction process, the deformed Coulomb energy can also be deduced from the total reaction cross section. For these heavy ion systems the empirical formulas depend only on quantities of the ingoing channels. Especially, the normalization of the Gaussian shaped element distributions indicates that the reminiscence on the entrance channel is not completely lost in dissipative collisions. For the 209 Bi + 136 Xe reaction at a laboratory bombarding energy of 1130 MeV the energy and element distributions are calculated which show an excellent agreement with the experimental data. (orig.)

  1. Trace elements and heavy metals in hair of stage III breast cancer patients.

    Benderli Cihan, Yasemin; Sözen, Selim; Oztürk Yıldırım, Sema

    2011-12-01

    This prospective study was designed to compare the hair levels of 36 elements in 52 patients with stage III breast cancer to those of an equal number of healthy individuals. Principal component and cluster analysis were used for source of identification and apportionment of heavy metals and trace elements in these two groups. A higher average level of iron was found in samples from patients while controls had higher levels of calcium. Both patients and controls had elevated levels of tin, magnesium, zinc, and sodium. Almost all element values in cancer patients showed higher dispersion and asymmetry than in healthy controls. Between the two groups, there were statistically significant differences in the concentrations of silver, arsenic, gold, boron, barium, beryllium, calcium, cadmium, cerium, cobalt, cesium, gadolinium, manganese, nickel, lead, antimony, scandium, selenium, and zinc (p heavy metals and trace elements in the hair of breast cancer patients in comparison to healthy controls. These results could be of significance in the diagnosis of breast cancer.

  2. The heavy ion fusion research program in West Germany

    Bock, R.

    1984-01-01

    The study on the feasibility of heavy ion beam for inertial confinement fusion was started four years ago, setting the main goal to identify and investigate the key issues of heavy ion fusion concept. The fund for this program has been provided by the Federal Ministry of Research and Technology. In this paper, the outline of the present research is shown, and some recent achievement is summarized. Moreover, the idea about the goal and the new direction of the future program are discussed. In the present program, two activities are distinguished, that is, the expermental and theoretical studies on accelerators, target physics and atomic physics, and the conceptual design study for a heavy ion-driven power plant. A RF linac with storage rings was chosen as the driver concept. In the accelerator research, ion source studies, RFQ development and beam transport measurement have been considered. Two beam transport experiments were carried out. In the conceptual design study, the HIBALL driver concept, the reactor chamber having the first wall protection using Pb-Li eutectic and so on have been studied. An accelerator facility of modest size has been suggested for basic accelerator physics studies. (Kako, I.)

  3. Exploring Ultra-Heavy Cosmic Rays with the Trans-Iron Galactic Element Recorder (TIGER)

    Link, Jason; Supertiger Collaboration

    2017-01-01

    Elements heavier than iron are primarily synthesized by neutron capture. These elements can be accelerated as cosmic-rays and measuring their abundances at Earth can yield information about galactic cosmic-rays' sources, the acceleration processes and the composition of the universe beyond the boundaries of our solar system. The Trans-Iron Galactic Element Recorder (TIGER) and its larger successor SuperTIGER was designed to measure the abundance of these ultra-heavy cosmic rays between Z=10 and Z=60. These detectors utilize scintillators with a wavelength shifter bar and PMT readout system as well as aerogel and acrylic Cherenkov detectors to identify the charge and energy of a particle and utilize a scintillating fiber hodoscope to provide trajectory information. In this talk I will review the results from this highly successful program, give the status for the next SuperTIGER flight planned for a December 2017 launch from Antarctica, and discuss the future direction of the program.

  4. In vivo detection of the toxic heavy elements, lead and cadmium

    Thomas, B.J.; Thomas, B.W.; Davey, J.F.; Baddeley, H.; Summers, V.; Craswell, P.

    1986-01-01

    Portable systems for the in vivo measurement of the toxic heavy elements, cadmium and lead are described. The cadmium concentration in either the liver or left kidney is determined using a technique of thermal neutron capture gamma-ray analysis. X-ray fluorescence analysis is used to measure lead within the bone of the second phalanx of the index finger. Each of the measurements is used as an index of long term exposure to the element and applied to screening of exposed industrial workers. The results of these industrial health applications are presented. Clinical application of the measurements to the study of the involvement of these elements in renal disease is described in brief. (author)

  5. Contamination and Health Risks from Heavy Metals (Cd and Pb and Trace Elements (Cu and Zn in Dairy Products

    Hamid Reza Ghafari

    2017-08-01

    Conclusion: Considering the serious contamination of some brands of butter and cheese by Cu and Pb, a control of heavy metals and trace elements levels during the whole production processing of dairy products must be applied.

  6. Directions for nuclear research in the transplutonium elements

    Wilhelmy, J.B.; Chasman, R.R.; Friedman, A.M.; Ahmad, I.

    1983-01-01

    The study of the heavy nuclides has played a vital role in our understanding of the alpha decay process, nuclear fission, nuclear binding energies and the limits of nuclear stability. This study has led to the understanding of novel shape degrees of freedom, such as the very large quadrupole deformations associated with the fission isomer process, and the very recently discovered octupole deformation. The existence of these unique phenomena in the heavy element region is not accidental. Fission isomerism is due to the delicate balance between nuclear forces holding the nucleus together and Coulomb forces causing nuclear fission. Octupole deformation arises from the increasing strength of matrix elements with increasing oscillator shell. Both illustrate the unique features of the heavy element region. Fission studies have given us information about large collective aspects in nuclei and the importance that nuclear structural effects can play in altering these macro properties. A new class of atomic studies has become possible with the availability of heavy elements. With these isotopes, we are now able to produce electric fields of such magnitude that it becomes possible to spontaneously create positron-electron pairs in the vacuum. We have organized this presentation into three major sections: nuclear structure, fission studies and atomic studies of supercritical systems. In each we will try to emphasize the new directions which can benefit from the continued availability of isotopes supplied by the Trans-plutonium Production Program. 117 references

  7. Status of the Holifield Heavy Ion Research Facility

    Martin, J.A.

    1978-01-01

    The Holifield Heavy Ion Research Facility presently operates the Oak Ridge Isochronous Cyclotron (ORIC). This accelerator provides heavy ions up to argon with energies useful for nuclear physics. The Phase I expansion of this facility, now a year away from completion, includes a 25-MV vertical folded tandem accelerator, beam transport and injection systems to use the ORIC as an energy booster, and additional experiment areas for the beams directly from the tandem. The tandem--cyclotron combination will provide heavy ions with energies up to 25 MeV/A for A 11 particles/sec. Building construction for the project is essentially complete. The accelerator manufacturer, National Electrostatics Corporation, has completed installation and testing of the 10-m-diam by 30-m-high accelerator pressure vessel and has begun installation of the accelerator systems. The accelerator has previously been assembled at the NEC plant and the digital control system operated without voltage on the column. Voltage tests are expected to begin in Oak Ridge in January 1979 with beam tests to begin in March. Completion of the project, including acceptance tests of the tandem and the beam injection system for ORIC is presently scheduled for November 15, 1979. Construction of Phase II for the facility wich will include a much larger booster cyclotron and additional research areas is expected to begin in 1982

  8. Two-loop massive operator matrix elements for unpolarized heavy flavor production to O({epsilon})

    Bierenbaum, I.; Bluemlein, J.; Klein, S. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Schneider, C. [Johannes Kepler Univ., Linz (Austria). Research Inst. for Symbolic Computation

    2008-02-15

    We calculate the O({alpha}{sup 2}{sub s}) massive operator matrix elements for the twist-2 operators, which contribute to the heavy flavor Wilson coefficients in unpolarized deeply inelastic scattering in the region Q{sup 2}>>m{sup 2}, up to the O({epsilon}) contributions. These terms contribute through the renormalization of the O({alpha}{sup 3}{sub s}) heavy flavor Wilson coefficients of the structure function F{sub 2}(x,Q{sup 2}). The calculation has been performed using light-cone expansion techniques without using the integration-by-parts method. We represent the individual Feynman diagrams by generalized hypergeometric structures, the {epsilon}-expansion of which leads to infinite sums depending on the Mellin variable N. These sums are finally expressed in terms of nested harmonic sums using the general summation techniques implemented in the Sigma package. (orig.)

  9. Charged particle induced delayed X-rays (DEX) for the analysis of intermediate and heavy elements

    Pillay, A. E.; Erasmus, C. S.; Andeweg, A. H.; Sellschop, J. P. F.; Annegarn, H. J.; Dunn, J.

    1988-12-01

    The emission of K X-rays from proton-rich and metastable radionuclides, following proton activation of the stable isotopes of the elements of interest, has not been widely used as a means of analysis. The thrust of this paper proposes a nuclear technique using delayed X-rays for the analysis of low concentrations of intermediate and heavy elements. The method is similar to the delayed gamma-ray technique. Proton bombardment induces mainly (p, n) reactions whereas the delayed X-rays originate largely from e --capture and isomeric transition. Samples of rare earth and platinum group elements (PGE), in the form of compacted powders, were irradiated with an 11 MeV proton beam and delayed X-rays detected with a 100 mm 2 Ge detector. Single element spectra for a range of rare earths and PGEs are presented. Analytical conditions are demonstrated for Pd in the range 0.1-5%. Spectra from actual geological samples of a PGE ore, preconcentrated by fire-assay, and monazite are presented. All six platinum group elements are visible and interference-free in a single spectrum, a marked advance on other nuclear techniques for these elements, including PIXE and neutron activation analysis (NAA).

  10. Interannual heavy element and nutrient concentration trends in the top sediments of Venice Lagoon (Italy)

    Masiol, Mauro; Facca, Chiara; Visin, Flavia; Sfriso, Adriano; Pavoni, Bruno

    2014-01-01

    Highlights: • Heavy element concentrations in sediments of a transitional system were studied. • Element contamination in the recent years has generally declined. • Mercury and cadmium contamination still remain above the limits in hot spots. • The role of sediment resuspension due to anthropogenic activity is discussed. • A basic knowledge to assess the impact of the MOSE construction is provided. - Abstract: The elemental composition of surficial sediments of Venice Lagoon (Italy) in 1987, 1993, 1998 and 2003 were investigated. Zn and Cr concentrations resulted in higher than background levels, but only Cd and Hg were higher than legal quality standards (Italian Decree 2010/260 and Water Framework Directive 2000/60/EC). Contaminants with similar spatial distribution are sorted into three groups by means of correlation analysis: (i) As, Co, Cd, Cu, Fe, Pb, Zn; (ii) Ni, Cr; (iii) Hg. Interannual concentrations are compared by applying a factor analysis to the matrix of differences between subsequent samplings. A general decrease of heavy metal levels is observed from 1987 to 1993, whereas particularly high concentrations of Ni and Cr are recorded in 1998 as a consequence of intense clam fishing, subsequently mitigated by better prevention of illegal harvesting. Due to the major role played by anthropogenic sediment resuspension, bathymetric variations are also considered

  11. LSI/CAMAC system for heavy elements research

    Watkins, E.D.; Dougan, R.J.; McQuaid, J.H.

    1985-01-01

    We have developed a LSI-11/23 computer-driven CAMAC data acquisition system. The 64 silicon-detector system is being used to investigate the alpha and spontaneous fission activities of short-lived transfermium isotopes by the real-time monitoring of the mother-daughter alpha decay sequence. A unique modular pulse processing electronics system was designed to simplify set up and calibration. The computer adjusts the gain of the CAMAC shaping amplifiers enabling the calibration and alignment of all 64 of the 1 k alpha spectra to within 0.5 channel in less than 10 minutes

  12. Status of the low-energy super-heavy element facility at RIKEN

    Schury, P., E-mail: schury@riken.jp [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Wada, M.; Ito, Y. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Arai, F. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Institute of Physics, University of Tsukuba, Tsukuba City, Ibaraki (Japan); Kaji, D. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Kimura, S. [Institute of Physics, University of Tsukuba, Tsukuba City, Ibaraki (Japan); Morimoto, K.; Haba, H. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Jeong, S. [Institute of Particle and Nuclear Studies (IPNS), High Energy Accelerator Research Organization (KEK), Ibaraki 305-0801 (Japan); Koura, H. [Advanced Science Research Center, Japan Atomic Energy Agency, Ibaraki 319-1195 (Japan); Miyatake, H. [Institute of Particle and Nuclear Studies (IPNS), High Energy Accelerator Research Organization (KEK), Ibaraki 305-0801 (Japan); Morita, K.; Reponen, M. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Ozawa, A. [Institute of Physics, University of Tsukuba, Tsukuba City, Ibaraki (Japan); Sonoda, T.; Takamine, A. [RIKEN, Nishina Center for Accelerator Based Science, Wako City, Saitama (Japan); Wollnik, H. [Dept. Chemistry and BioChemistry, New Mexico State University, Las Cruces, NM (United States)

    2016-06-01

    In order to investigate nuclei produced via fusion–evaporation reactions, especially super-heavy elements (SHE), we have begun construction of a facility for conversion of fusion–evaporation residues (EVR) to low-energy beams. At the base of this facility is a small cryogenic gas cell utilizing a traveling wave RF-carpet, located directly following the gas-filled recoil ion separator GARIS-II, which will thermalize EVRs to convert them into ion beams amenable to ion trapping. We present here the results of initial studies of this small gas cell.

  13. Evolution of heavy-element abundances in the galactic halo and disk

    Mathews, G.J.; Cowan, J.J.; Schramm, D.N.

    1988-05-01

    The constraints on the universal energy density and cosmological constant from cosmochronological ages and the Hubble age are reviewed. Observational evidence for the galactic chemical evolution of the heavy-element chronometers is described in the context of numerical models. The viability of the recently discovered Th/Nd stellar chronometer is discussed, along with the suggestion that high r-process abundances in metal-poor stars may have resulted from a primordial r-process, as may be required by some inhomogeneous cosmologies

  14. Experimental research of fuel element reliability

    Cech, B.; Novak, J.; Chamrad, B.

    1980-01-01

    The rate and extent of the damage of the can integrity for fission products is the basic criterion of reliability. The extent of damage is measurable by the fission product leakage into the reactor coolant circuit. An analysis is made of the causes of the fuel element can damage and a model is proposed for testing fuel element reliability. Special experiments should be carried out to assess partial processes, such as heat transfer and fuel element surface temperature, fission gas liberation and pressure changes inside the element, corrosion weakening of the can wall, can deformation as a result of mechanical interactions. The irradiation probe for reliability testing of fuel elements is described. (M.S.)

  15. RESEARCH OIL RECOVERY MECHANISMS IN HEAVY OIL RESERVOIRS

    Anthony R. Kovscek; William E. Brigham

    1999-06-01

    The United States continues to rely heavily on petroleum fossil fuels as a primary energy source, while domestic reserves dwindle. However, so-called heavy oil (10 to 20{sup o}API) remains an underutilized resource of tremendous potential. Heavy oils are much more viscous than conventional oils. As a result, they are difficult to produce with conventional recovery methods such as pressure depletion and water injection. Thermal recovery is especially important for this class of reservoirs because adding heat, usually via steam injection, generally reduces oil viscosity dramatically. This improves displacement efficiency. The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties; (2) in-situ combustion; (3) additives to improve mobility control; (4) reservoir definition; and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx. Significant results are described.

  16. Research and development in heavy and extra heavy oil upgrading in PDVSA-Intevep: aqua conversion

    Pereira, Pedro; Machin, Ivan; Salerno, Gladys; Cotte, Edgar; Higuerey, Ingrid; Andriollo, Antida; Cordova, Jose; Zacarias, Luis; Marzin, Roger; Rivas, Guaicaipuro

    1999-01-01

    After twenty five years of Intevep's creation, is now a good time to revise, from a technical and conceptual perspective, some of the ideas developed in one of the activities that this institution has more persistently sustained. The referred activity targets at the generation of new processes for the upgrading of the bitumen or extra heavy crude oils that Venezuela possesses. This revision concludes in an eclectic synthesis method for the selection and harmonization of the various different advances made through the research performed on processes such as HDH, coking, visbreaking, partial or selective steam reforming and others. Thus, from conceptually different research perspectives a new PDVSA's process already known as as aqua conversion has been assembled. The deepening in the use of this methodology may lead to other new and better upgrading technologies or to improve the existing for the same. All this keeping in mind that whatever these technologies are proprietary or from third parties is of low relevance in front of the mayor objective of commercializing the wide extra heavy oil reservoirs of this country

  17. Exploring Elements of Fun to Motivate Heavy Drinking Youth to (retrain Cognition

    Wouter Boendermaker

    2015-09-01

    Adding (social game elements can increase motivation to train, and while the mobile training did not appear to be more motivating, it also did not underperform compared to the regular training in this sample. This warrants more research into motivational elements for CBM training in younger audiences.

  18. Workshop of Advanced Science Research Center, JAERI. Nuclear physics and nuclear chemistry of superheavy elements

    Nishio, Katsuhisa; Nishinaka, Ichiro; Ikezoe, Hiroshi; Nagame, Yuichiro

    2004-03-01

    A liquid drop model predicts that the fission barrier of a nucleus whose atomic number (Z) is larger than 106 disappears, so that such heavier nuclei as Z > 106 cannot exist. The shell effect, however, drastically changes structure of the fission barrier and stabilizes nucleus against fission, predicting the presence of super heavy element (SHE, Z=114-126) with measurable half-life. In the SHE region, a wave function of outermost electron of an atom, which controls chemical properties of an elements, is disturbed or changed by relativistic effects compared to the one from the non-relativistic model. This suggests that the SHEs have different chemical properties from those of lighter elements belonging to the same family. The chemistry of SHEs requires event by event analysis to reveal their chemical properties, thus is called 'atom-at-a-time chemistry'. Japan Atomic Energy Research Institute (JAERI) has been investigating fusion mechanism between heavy nuclei to find out favorable reactions to produce SHE by using JAERI-tandem and booster accelerator. In the JAERI-tandem facility, isotopes of Rf and Db are produced by using actinide targets such as 248 Cm in order to investigate their chemical properties. The present workshop was held in Advanced Science Research Center of JAERI at February 27-28 (2003) in order to discuss current status and future plans for the heavy element research. The workshop also included topics of the radioactive nuclear beam project forwarded by the JAERI-KEK cooperation and the nuclear transmutation facility of J-PARC. Also included is the nuclear fission process as a decay characteristic of heavy elements. There were sixty participants in the workshop including graduate and undergraduate eleven students. We had guests from Germany and Hungary. Through the workshop, we had a common knowledge that researches on SHE in Japan should fill an important role in the world. (author)

  19. Research on oil recovery mechanisms in heavy oil reservoirs

    Kovscek, Anthony R.; Brigham, William E., Castanier, Louis M.

    2000-03-16

    The research described here was directed toward improved understanding of thermal and heavy-oil production mechanisms and is categorized into: (1) flow and rock properties, (2) in-situ combustion, (3) additives to improve mobility control, (4) reservoir definition, and (5) support services. The scope of activities extended over a three-year period. Significant work was accomplished in the area of flow properties of steam, water, and oil in consolidated and unconsolidated porous media, transport in fractured porous media, foam generation and flow in homogeneous and heterogeneous porous media, the effects of displacement pattern geometry and mobility ratio on oil recovery, and analytical representation of water influx.

  20. Correlation of Heavy Element in Sea Water and Sediment Samples from Peninsula of Muria

    Rosidi; Sukirno

    2007-01-01

    The analysis of heavy metals in marine environmental samples peninsula of Muria in the year 2004 has been carried out by using neutron activation analysis (NAA) method. The objective of this analysis is to know the distribution of heavy metals in the sea water and sediment, which accommodate the recent environmental data in supporting the license of site for the nuclear power plants (NPP). The result of the analysis show that there were only 5 observed elements found in sea water and sediment were Cd, Co, Cr, Sb and Sc. All of heavy metals from sea water (0.002 mg/l) are obviously lower than the threshold value established by environmental minister Act; Kep LH No 51/2004. From the observed data to use software of SPSS version 10, application of the Pearson correlation (r) shows that between Co with Sc was indicator show a highly positive significant correlation (r=0.928), between Cr with Sc was sufficiently positive high (r=0.756), between Cr with Cd was precisely (r=0.611) while Co with Sb shows the significantly low (r=0.429). (author)

  1. A Taxonomy for Heavy-Duty Telemanipulation Tasks Using Elemental Actions

    Alexander Owen-Hill

    2013-10-01

    Full Text Available In the maintenance of large scientific facilities, telemanipulation procedures can involve various subprocedures which in turn are made up of a sequence of subtasks. This work presents a taxonomy which describes a set of elemental actions for heavy-duty telemanipulation, along with an example of these actions in a standard maintenance subprocedure. As maintenance tasks are often very different at high-level, this generalized way of deconstructing tasks allows a highly adaptable approach to describe the sequence of any procedure, which can then be used for such applications as task monitoring, automation or detection of incomplete tasks. We describe in detail the properties of each elemental action and apply the taxonomy to an example subprocedure to show how the process can be generalizable. An automatic state-machine creation stage is shown, which would be used at the task scheduling stage to simplify calculations carried out during the moment-by-moment execution of the task.

  2. The determination of sulfur and some heavy elements in the coke

    Ma'rouf, M.

    2003-01-01

    The content of free sulfur and some heavy elements in the coke resulting from the residua of oil industry was determined bu using various technical analytical methods. The flame technique of atomic absorption FAAS was used to identify lead, copper, zinc, chromium, VGA-AAS and determine arsenic and selenium, CV-AAS to the determination of mercury. As for sulfur, it was determined by using the total oxidation method at high temperatures (1100 C 0 ). The IR indicator was used for further determination. The relative standard deviation in the determination of sulfur did not exceed the limits of 0.01 and 0.02, compared to the determination of other elements by using the atomic absorption method. (Author)

  3. Heavy metals and trace elements in atmospheric fall-out: Their relationship with topsoil and wheat element composition

    Bermudez, Gonzalo M.A., E-mail: gbermudez@com.uncor.edu [Instituto Multidisciplinario de Biologia Vegetal (IMBIV), CONICET (Argentina); Catedra de Quimica General, FCEFyN, Universidad Nacional de Cordoba, Avda. Velez Sarsfield 1611, Ciudad Universitaria (X5016 GCA), Cordoba (Argentina); Jasan, Raquel; Pla, Rita [Tecnicas Analiticas Nucleares, Comision Nacional de Energia Atomica (CAE), Presbitero Gonzalez y Aragon N Degree-Sign 15 (B1802AYA), Ezeiza (Argentina); Pignata, Maria L. [Instituto Multidisciplinario de Biologia Vegetal (IMBIV), CONICET (Argentina); Catedra de Quimica General, FCEFyN, Universidad Nacional de Cordoba, Avda. Velez Sarsfield 1611, Ciudad Universitaria (X5016 GCA), Cordoba (Argentina)

    2012-04-30

    Highlights: Black-Right-Pointing-Pointer Metal and trace element deposition rates and concentrations in bulk samples. Black-Right-Pointing-Pointer Anthropogenic vs. natural sources were identified using enrichment factors and PCA. Black-Right-Pointing-Pointer Anthropogenic sources for Ca, Cd, Cu, Fe, Mn, Ni, Pb, Sb, U, Zn and lanthanides. Black-Right-Pointing-Pointer Main sources were a cement plant, chemical-mechanical industries, cities and mining. Black-Right-Pointing-Pointer Metals in wheat grain were predicted by soil and bulk deposition composition. - Abstract: The objectives of this study were to determine the average concentrations and deposition rates of 28 elements in atmospheric bulk deposition and to elucidate associations among topsoil, bulk deposition and wheat element composition. The fluxes of arsenic (As), copper (Cu), lead (Pb) and zinc (Zn) deposition in Cordoba were higher than in other agro-ecosystems, which reflects both natural (geochemistry and topsoil removal) and anthropogenic sources. High lanthanide, uranium (U) and thorium (Th) concentrations revealed the impact of an open cast uranium mine. The highest enrichment factors (EF) were those of Cu, Pb, Zn and nickel (Ni), with calcium (Ca) being the most prominent in the surroundings of a cement plant. Industries and the transport of airborne urban pollutants were the main anthropogenic sources for Ca, Cu, Ni, Pb, Zn, cadmium (Cd), iron (Fe), manganese (Mn) and antimony (Sb). The concentrations of metals in wheat grain were predicted using the topsoil and atmospheric fall-out composition with R{sup 2} = 0.90, with the latter being the best explanatory variable. The present study highlights the potential health hazards of wheat consumption (Environmental Protection Agency) by the assessment of heavy metals in bulk atmospheric deposition.

  4. Spin spectrometer at the holified heavy-ion research facility and some planned experiments

    Sarantites, D.G.; Jaaskelainen, M.; Hood, J.T.; Woodward, R.; Barker, J.H.; Hensley, D.C.; Halbert, M.L.; Chan, Y.D.

    1980-01-01

    The 4π multidetector γ-ray spectrometer at the Holified Heavy-ion Research Facility (HHIRF) is described in some detail. The following important features of this spectrometer are discussed: (a) the geometric arrangement, (b) the actual performance of the individual detector elements, (c) the associated electronics and data acquisition system, and (d) the response of the system to input γ-cascades including the effect of crystal-to-crystal scattering and the response to neutrons. The first few experiments to be performed are briefly described

  5. [Determination of Heavy Metal Elements in Diatomite Filter Aid by Inductively Coupled Plasma Mass Spectrometry].

    Nie, Xi-du; Fu, Liang

    2015-11-01

    This study established a method for determining Be, Cr, Ni, As, Cd, Sb, Sn, Tl, Hg and Pb, total 10 heavy metals in diatomite filter aid. The diatomite filter aid was digested by using the mixture acid of HNO₃ + HF+ H₃PO₄ in microwave system, 10 heavy metals elements were determined by inductively coupled plasma mass spectrometry (ICP-MS). The interferences of mass spectrometry caused by the high silicon substrate were optimized, first the equipment parameters and isotopes of test metals were selected to eliminate these interferences, the methane was selected as reactant gas, and the mass spectral interferences were eliminated by dynamic reaction cell (DRC). Li, Sc, Y, In and Bi were selected as the internal standard elements to correct the interferences caused by matrix and the drift of sensitivity. The results show that the detection limits for analyte is in the range of 3.29-15.68 ng · L⁻¹, relative standard deviations (RSD) is less than 4.62%, and the recovery is in the range of 90.71%-107.22%. The current method has some advantages such as, high sensitivity, accurate, and precision, which can be used in diatomite filter aid quality control and safety estimations.

  6. AMS of heavy elements with an ECR ion source and the ATLAS linear accelerator

    Paul, M; Ahmad, I; Borasi, F; Caggiano, J; Davids, C N; Greene, J P; Harss, B; Heinz, A; Henderson, D J; Henning, W F; Jiang, C L; Pardo, R C; Rehm, K E; Rejoub, R; Seweryniak, D; Sonzogni, A; Uusitalo, J; Vondrasek, R C

    2000-01-01

    Detection of heavy elements by accelerator mass spectrometry with the electron cyclotron resonance ion source, Argonne linear accelerator and fragment mass analyzer (ECRIS-ATLAS-FMA) system has been developed. The use of the ECR-ATLAS system for AMS of heavy elements has two interesting features: (i) the efficient production of high-charge state ions in the ECR source ensures the elimination of molecular ions at the source stage, a highly attractive feature for any mass-spectrometric use not exploited so far; (ii) the linear acceleration based on velocity matching and the beam transport system act as a powerful mass filter for background suppression. We have shown that our system reaches an abundance sensitivity of 1x10 sup - sup 1 sup 4 for Pb isotopes. The sup 2 sup 3 sup 6 U detection sensitivity is sup 2 sup 3 sup 6 U/U > or approx. 1x10 sup - sup 1 sup 2 , limited mainly by the ion source output.

  7. Determination of trace elements and heavy metals in sediment using x-ray fluorescence

    Sidahmed, Muataz Ahmed Ibrahem

    2014-01-01

    In this study, 30 sediment samples were taken randomly from the area of Suba south of Khartoum state. Trace elements and heavy metal were determined in sediments samples using x-ray fluoresce spectroscopy (X RF). K, Ca, Ti, Mn, Fe, Cu, Zn, Pb, Rb, Sr, and Zr were determined by X RF. Standard Reference Material (SRM) from international Atomic Energy Agency (IAEA-Soil-7) has been used to achieve accuracy of X RF method. Measured values were found in agreements with certified values. The average elemental concentrations of K, Ca, Ti, Mn, Fe, Cu, Zn, Pb, Rb, Sr, and Zr were 5882.7, 20703.3, 6264.3, 460.97, 26713.3, 7.7, 43.4, 18.6, 28.6, 144.8, and 173.06, respectively. Correlation between elements was performed also cluster analysis was used to check the similarly between the samples result. The result of study were compared with previous studies and the concentrations of some elements found to be similar.(Author)

  8. Experimental investigation in separating the heavy metal elements of refuse incineration fly ashes by using molten iron

    Yang, J. [Chongqing Univ., Chongqing (China)]|[CPI-Yuanda Environmental-protection Engineering Co. Ltd., Chongqing (China); Liu, Q.; Dong, L. [Chongqing Univ., Chongqing (China); Du, Y. [CPI-Yuanda Environmental-protection Engineering Co. Ltd., Chongqing (China)

    2008-07-01

    One of the main waste treatment methods in the world for municipal solid waste (MSW) is incineration. It is effective in toxic substance destruction, waste volume reduction, and energy recovery. Some chemical substances are accumulated during incineration, most notably lead, zinc, chromium and cadmium, as well as other heavy metals. Untreated fly ash disposed in landfills can pollute the soil, surface water and groundwater because of the high levels of hazardous heavy metals and high salt concentration that can be leached out. This paper presented an experiment that melt-separated the heavy metal elements from fly ash generated during refuse incineration. Molted iron, was used as resolvent to dissolve the heavy metal elements in it. The paper described the materials and methods as well as the results of the study. It was concluded that using molted iron to separate the heavy metal elements from MSW incineration fly ash was feasible. The removal ratio of the main heavy metal elements was above 80 per cent, and some of it was above 99 per cent. 5 refs., 7 tabs., 1 fig.

  9. Relative measurement of heavy elements in the bile gallbladder and gallstone

    Moosavi, K.; Vatankhah, S.; Salimi, J.

    2006-01-01

    Particle Induced X-Ray Emission is a suitable method for the analysis of biological samples in which heavy trace elements are contained in light matrix elements. It is very important to know which factors or probably elements act as initial seed and lead to growing the sands. The goal of this study was to compare the relative values of Fe/K, Cu/K and Zn/K for gallstones, gallbladder, and bile of a specific patient for studying the origination of forming the gallstones. Materials and Methods Human gallbladder, bile, and gallstone samples were obtained by surgical operation from 15 patients and are bombarded by 2.0 MeV energy proton beams produced by van de Graaff accelerator in vacuum. All .. the gallstones were chosen of pigment type of stones and, all the patients were adults. In contrast with conventional methods, the shell and center of the sands has been analyzed separately. The PIXE spectrum analysis was performed using the nonlinear least square fitting code AXIL and GUPIX. Results: The results of detected minor and trace elements shows that the precipitation of calcium salt in the bile lead to reduction of crystals' formation. Elemental comparison of pigment type of gallstone and bile shows that the concentration of calcium in the shell of the stones is four times more than that in the bile. Conclusion: Precipitation of the calcium from the saturated bile on the cholesterols as a seed of gallstones led to reduced sands formation. Analysis of the gallbladder of the same patients revealed no relation between elemental concentrations of bile and gallstones

  10. Heavy element accumulation in Evernia prunastri lichen transplants around a municipal solid waste landfill in central Italy.

    Nannoni, Francesco; Santolini, Riccardo; Protano, Giuseppe

    2015-09-01

    This paper presents the results of a biomonitoring study to evaluate the environmental impact of airborne emissions from a municipal solid waste landfill in central Italy. Concentrations of 11 heavy elements, as well as photosynthetic efficiency and cell membrane integrity were measured in Evernia prunastri lichens transplanted for 4months in 17 monitoring sites around the waste landfill. Heavy element contents were also determined in surface soils. Analytical data indicated that emissions from the landfill affected Cd, Co, Cr, Cu, Ni, Pb, Sb and Zn concentrations in lichens transplanted within the landfill and along the fallout direction. In these sites moderate to severe accumulation of these heavy elements in lichens was coupled with an increase in cell membrane damage and decrease in photosynthetic efficiency. Nevertheless, results indicated that landfill emissions had no relevant impact on lichens, as heavy element accumulation and weak stress symptoms were detected only in lichen transplants from sites close to solid waste. The appropriate management of this landfill poses a low risk of environmental contamination by heavy elements. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Trace elements in land plants: concentration ranges and accumulators of rare earths, Ba, Ra, Mn, Fe, Co and heavy halogens

    Koyama, M.; Shirakawa, M.; Takada, J.; Katayama, Y.; Matsubara, T.

    1987-01-01

    More than 2000 samples of land plant leaves, mostly of tree, were analyzed by neutron activation analysis in order to find out macroscopic relations between distributions of chemical elements in plants and soil characteristics. The distributions of the elements in plants were also examined from the view point of botanical taxonomy or phylogeny. New species which accumulate Co, rare earths, Ba, Ra, heavy halogens and some other elements were found. Capability or potentiality for accumulating elements could be related to higher ranks of taxonomy, that is, genus or family. The nature of soil is also found to have profound effects on the extent of accumulation of elements in plants. (author)

  12. Effects of elemental sulphur on heavy metal uptake by plants growing on municipal sewage sludge.

    Dede, Gulgun; Ozdemir, Saim

    2016-01-15

    In this study experiment was carried out to determine the phytoextraction potential of six plant species (Conium maculatum, Brassica oleraceae var. oleraceae, Brassica juncea, Datura stramonium, Pelargonium hortorum and Conyza canadensis) grown in a sewage sludge medium amended with metal uptake promoters. The solubility of Cu, Cd and Pb was significantly increased with the application of elemental S due to decrease of pH. Faecal coliform number was markedly decreased by addition of elemental sulphur. The extraction of Cu, Cr and Pb from sewage sludge by using B. juncea plant was observed as 65%, 65% and 54% respectively that is statistically similar to EDTA as sulphur. The bioaccumulation factors were found higher (>1) in the plants tested for Cu and Pb like B. juncea. Translocation index (TI) calculated values for Cd and Pb were greater than one (>1) in both C. maculatum and B. oleraceae var. oleraceae. The results cleared that the amendment of sludge with elemental sulphur showed potential to solubilize heavy metals in phytoremediation as much as EDTA. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Heavy metals and other elements in serum of cattle from organic and conventional farms.

    Tomza-Marciniak, Agnieszka; Pilarczyk, Bogumiła; Bąkowska, Małgorzata; Pilarczyk, Renata; Wójcik, Jerzy

    2011-11-01

    Concentrations of cadmium, lead, iron, zinc, copper, chromium, nickel, aluminium and arsenium were analysed in blood serum of cattle from organic (n=20) and conventional (n=21) farms. The elements were determined by inductively coupled plasma atomic emission spectrometry using an Optima 2000 DV instrument (Perkin Elmer Inc.). Animals from the organic farm were characterised by significantly lower (Panimals from the conventional farm. The concentration of Cd was similar in animals from both organic and conventional farms. The concentration of toxic elements in cattle from organic and conventional farms studied was very low. The trace essential elements were generally within the adequate ranges except Zn and Cu, which were deficient. In organically reared animals, also serum Fe content was below the critical level for diagnosing iron deficiency. Pb was significantly correlated with Cd, Zn, Fe, Cu and Ni. A significant positive correlation between the concentration of Cd and Zn, Cu and Ni concentrations was only observed in cows from the organic farm. The present results suggest that organically raised animals are less exposed to harmful environmental influences such as the environmental pollution with heavy metals. On the other hand, these animals are at a greater risk of mineral deficiency compared to animals kept on conventional farms.

  14. Workshop on environmental research for actinide elements

    Watters, R.L.

    1978-01-01

    The topics of discussion in this fourth workshop centered on the adequacy of plutonium information, the needs and direction of future transuranium research and the research necessary for an appraisal of the potential hazards associated with thorium and high specific activity uranium isotopes. These topics were discussed in four panels which have prepared reports that make up the body of these proceedings. The four panels were: ecosystem research; plant/soils research; marine and freshwater research; and statistics and modeling. In addition to the appraisal and planning studies, a report was given on an intercomparison of analytical quality control

  15. Research of flaw assessment methods for beryllium reflector elements

    Shibata, Akira; Ito, Masayasu; Takemoto, Noriyuki; Tanimoto, Masataka; Tsuchiya, Kunihiko; Nakatsuka, Masafumi; Ohara, Hiroshi; Kodama, Mitsuhiro

    2012-02-01

    Reflector elements made from metal beryllium is widely used as neutron reflectors to increase neutron flux in test reactors. When beryllium reflector elements are irradiated by neutron, bending of reflector elements caused by swelling occurs, and beryllium reflector elements must be replaced in several years. In this report, literature search and investigation for non-destructive inspection of Beryllium and experiments for Preliminary inspection to establish post irradiation examination method for research of characteristics of metal beryllium under neutron irradiation were reported. (author)

  16. After the activation of heavy elements in the course of experiments: intermediate storage and disposal

    Ehrlicher, U.; Beer, H.F.

    2005-01-01

    When materials are foreseen to be activated in the course of experiments, radiation protection must also be considered from the aspect of waste disposal. Materials containing heavy elements still can bear some TBq of activity 10 years after irradiation with neutrons or heavy particles in an accelerator. The potential danger has to be assessed for each storage position in behalf of planning protective measures. For the longest period, however, the material will rest in an interim storage like the BZL in Wuerenlingen, Switzerland, waiting for its final disposal. PSI calculates the maximum personal dose for accidents (plane crash followed by a fire hazard) to assess the potential risk around the BZL. The following speech will deal with items like: personal dose for the inhabitants of communities in the vicinity of the BZL after a possible accident before and after the storage of the activated materials, adherence to the aims of protection (personal dose of less than 100 mSv), possible measures to minimize the potential danger, (orig.)

  17. Scattering chamber for the Holifield Heavy Ion Research Facility

    Goodman, C.D.; Corum, J.E.

    1977-09-01

    A conceptual design is presented for a 62-in.-diam. general purpose scattering chamber to be used for nuclear research with heavy ions. The detector rotation mechanism is based on large diameter (approx. 58 in.) peripherally driven rings. This leaves the central region open for detectors and other apparatus and permits the use of a perpendicular ring for rotating a detector out of the reaction plane. A precision target slide with provisions for removing the entire slide under vacuum is part of the design. Access and viewing ports on the dished top and in the reaction plane will be provided. Cryogenic pumping will be used to keep the vacuum free from hydrocarbon vapors, water vapor, and oxygen

  18. Study of the behaviour of some heavy elements in solvents containing hydrogen fluoride

    Tarnero, M.

    1967-01-01

    The anhydrous liquid mixtures: dinitrogen tetroxide-hydrogen fluoride and antimony pentafluoride-hydrogen fluoride were studied as solvents for heavy elements interesting nuclear energy: uranium, thorium, zirconium and for some of their compounds. For N 2 O 4 -HF mixtures, electric conductivity measurements and liquid phase infrared spectra were also obtained. Uranium and zirconium tetrafluoride are much more soluble in N 2 O 4 -HF mixtures than in pure hydrogen fluoride. Uranium dissolved in these mixtures is pentavalent. In SbF 5 -HF mixtures, uranium dissolves with hydrogen evolution and becomes trivalent. The solid compound resulting from the dissolution is a fluoro-antimonate: U(SbF 6 ) 3 . (author) [fr

  19. A method for the quantitative analysis of heavy elements by X-ray fluorescence

    Souza Caillaux, Z. de

    1981-01-01

    A study of quantitative analysis methodology by X-ray fluorescence analysis is presented. With no damage to precision it makes possible an analysis of heavy elements in samples with the form and texture as they present themselves. Some binary alloys were examined such as: FeCo; CuNi; CuZn; AgCd; AgPd; AuPt e PtIr. The possibility of application of this method is based on the compromise solutIon of wave lengths and the intensity of the homologous emission and absorption edges of constituents with the quantic efficiency of the detector, the dispersion and the wave lenght resolution of crystal analyser, and the uniformity of the excitation intensity. (Author) [pt

  20. K-edge x-ray fluorescence analysis for actinide and heavy elements solution concentration measurements

    Camp, D.C.

    1984-07-01

    Advantages of using Co-57 as an exciter for K XRFA include: a compact design that requires no x-ray tubes; the exciter-detector assembly locates remote from support electronics; on-line, at-line, or off-line configurations for monitor/measurements; systems that can be run by semi-skilled technicians, once programmed; and operated via remote terminals with results sent to control rooms; heavy element concentrations that are measurable thru industrial pipes; independent of minor changes in solution matrix or source half life with concentration results reported in near-real-time; a dynamic range of measurable concentrations that is greater than 10 4 ; measurement times that are reasonable even at 1 gram/liter; and for nuclear safeguards, it provides the <0.5% accuracy required by DOE for the accountability of U, Pu, or both, once the system is calibrated

  1. Study of particulates and heavy elements in air of some Syrian cities

    Othman, I.; Al-Oudat, M.; Al-Rayes, A. H.; Al- Kharfan, K.

    1999-11-01

    A study of air pollution in different sites of five Syrian cities (Damascus, Aleppo, Tartous, Homs, and Sweda) was carried out. The concentration of total suspended particulate (TSP), particulate less than 10 microns (PM 10) and less than 3 microns (PM 3) were measured using high volume air sampler (HVAS). Heavy element concentration, Pb, Cd, Zn, and Cu were also determined using anodic stripping voltametry. The result showed that TSP, PM 10 and PM 3 were higher than WHO standards in several times. Mean lead concentrations ranged between 0.58 and 2.96 μg/m 3 and 0.56 and 1.53 μg/m 3 in Damascus and Aleppo respectively, while in the other cities these concentrations were less than WHO standards (0.5 - 1 μg/m 3 ). (author)

  2. Recovery of the heavy elements by NaY AND NaZSM-5 sorbant materials

    Nibou, D.; Lebail, S.

    1997-04-01

    Porous sorbants as zeolites have a several applications in differents fiels: industrial gas purification, catalysis, transformation hydrocarbures prosesses and exchange ions. The hiogh capacity to exchange their cations with those of aqueous solutions was known (1). Since the accession of synthetic zeolites, these silicates have invaded the market and the firstindustrial applications were in exchange field. Studies at Battelle Northwest in Rchland, Washington have shown that zeolites may be used in treatment of radioactive wastes (2). The used method for storing the isotopes is based on selective removal by ion exchange. Clinoptilolite, zeolite (modernite), NaA, and AW-500 have been used. In this context, the present work deals with the recovery of heavy metals like lead and uranium using some microporous materials. The obtained results show that NaY faujasite and NaZSM-5 of the FAU- and MFI-type structure respectively are very effective in removing these elements from waste water

  3. Interannual heavy element and nutrient concentration trends in the top sediments of Venice Lagoon (Italy).

    Masiol, Mauro; Facca, Chiara; Visin, Flavia; Sfriso, Adriano; Pavoni, Bruno

    2014-12-15

    The elemental composition of surficial sediments of Venice Lagoon (Italy) in 1987, 1993, 1998 and 2003 were investigated. Zn and Cr concentrations resulted in higher than background levels, but only Cd and Hg were higher than legal quality standards (Italian Decree 2010/260 and Water Framework Directive 2000/60/EC). Contaminants with similar spatial distribution are sorted into three groups by means of correlation analysis: (i) As, Co, Cd, Cu, Fe, Pb, Zn; (ii) Ni, Cr; (iii) Hg. Interannual concentrations are compared by applying a factor analysis to the matrix of differences between subsequent samplings. A general decrease of heavy metal levels is observed from 1987 to 1993, whereas particularly high concentrations of Ni and Cr are recorded in 1998 as a consequence of intense clam fishing, subsequently mitigated by better prevention of illegal harvesting. Due to the major role played by anthropogenic sediment resuspension, bathymetric variations are also considered. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. HELAC-Onia: an automatic matrix element generator for heavy quarkonium physics

    Shao, Hua-Sheng

    2013-01-01

    By the virtues of the Dyson-Schwinger equations, we upgrade the published code \\mtt{HELAC} to be capable to calculate the heavy quarkonium helicity amplitudes in the framework of NRQCD factorization, which we dub \\mtt{HELAC-Onia}. We rewrote the original \\mtt{HELAC} to make the new program be able to calculate helicity amplitudes of multi P-wave quarkonium states production at hadron colliders and electron-positron colliders by including new P-wave off-shell currents. Therefore, besides the high efficiencies in computation of multi-leg processes within the Standard Model, \\mtt{HELAC-Onia} is also sufficiently numerical stable in dealing with P-wave quarkonia (e.g. $h_{c,b},\\chi_{c,b}$) and P-wave color-octet intermediate states. To the best of our knowledge, it is a first general-purpose automatic quarkonium matrix elements generator based on recursion relations on the market.

  5. Sub-barrier quasifission in heavy element formation reactions with deformed actinide target nuclei

    Hinde, D. J.; Jeung, D. Y.; Prasad, E.; Wakhle, A.; Dasgupta, M.; Evers, M.; Luong, D. H.; du Rietz, R.; Simenel, C.; Simpson, E. C.; Williams, E.

    2018-02-01

    Background: The formation of superheavy elements (SHEs) by fusion of two massive nuclei is severely inhibited by the competing quasifission process. Low excitation energies favor SHE survival against fusion-fission competition. In "cold" fusion with spherical target nuclei near 208Pb, SHE yields are largest at beam energies significantly below the average capture barrier. In "hot" fusion with statically deformed actinide nuclei, this is not the case. Here the elongated deformation-aligned configurations in sub-barrier capture reactions inhibits fusion (formation of a compact compound nucleus), instead favoring rapid reseparation through quasifission. Purpose: To determine the probabilities of fast and slow quasifission in reactions with prolate statically deformed actinide nuclei, through measurement and quantitative analysis of the dependence of quasifission characteristics at beam energies spanning the average capture barrier energy. Methods: The Australian National University Heavy Ion Accelerator Facility and CUBE fission spectrometer have been used to measure fission and quasifission mass and angle distributions for reactions with projectiles from C to S, bombarding Th and U target nuclei. Results: Mass-asymmetric quasifission occurring on a fast time scale, associated with collisions with the tips of the prolate actinide nuclei, shows a rapid increase in probability with increasing projectile charge, the transition being centered around projectile atomic number ZP=14 . For mass-symmetric fission events, deviations of angular anisotropies from expectations for fusion fission, indicating a component of slower quasifission, suggest a similar transition, but centered around ZP˜8 . Conclusions: Collisions with the tips of statically deformed prolate actinide nuclei show evidence for two distinct quasifission processes of different time scales. Their probabilities both increase rapidly with the projectile charge. The probability of fusion can be severely

  6. Transportable Heavy Duty Emissions Testing Laboratory and Research Program

    David Lyons

    2008-03-31

    The objective of this program was to quantify the emissions from heavy-duty vehicles operating on alternative fuels or advanced fuel blends, often with novel engine technology or aftertreatment. In the first year of the program West Virginia University (WVU) researchers determined that a transportable chassis dynamometer emissions measurement approach was required so that fleets of trucks and buses did not need to be ferried across the nation to a fixed facility. A Transportable Heavy-Duty Vehicle Emissions Testing Laboratory (Translab) was designed, constructed and verified. This laboratory consisted of a chassis dynamometer semi-trailer and an analytic trailer housing a full scale exhaust dilution tunnel and sampling system which mimicked closely the system described in the Code of Federal Regulations for engine certification. The Translab was first used to quantify emissions from natural gas and methanol fueled transit buses, and a second Translab unit was constructed to satisfy research demand. Subsequent emissions measurement was performed on trucks and buses using ethanol, Fischer-Tropsch fuel, and biodiesel. A medium-duty chassis dynamometer was also designed and constructed to facilitate research on delivery vehicles in the 10,000 to 20,000lb range. The Translab participated in major programs to evaluate low-sulfur diesel in conjunction with passively regenerating exhaust particulate filtration technology, and substantial reductions in particulate matter were recorded. The researchers also participated in programs to evaluate emissions from advanced natural gas engines with closed loop feedback control. These natural gas engines showed substantially reduced levels of oxides of nitrogen. For all of the trucks and buses characterized, the levels of carbon monoxide, oxides of nitrogen, hydrocarbons, carbon dioxide and particulate matter were quantified, and in many cases non-regulated species such as aldehydes were also sampled. Particle size was also

  7. Heavy Ion Fusion Accelerator Research (HIFAR) half-year report, October 1, 1988--March 31, 1989

    1989-06-01

    The basic objective of the Heavy Ion Fusion Accelerator Research (HIFAR) program is to assess the suitability of heavy ion accelerators as igniters for Inertial Confinement Fusion (ICF). A specific accelerator technology, the induction linac, has been studied at the Lawrence Berkeley Laboratory and has reached the point at which its viability for ICF applications can be assessed over the next few years. The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the validation of new accelerator strategies, to cut costs. Key elements to be addressed include: beam quality limits set by transverse and longitudinal beam physics; development of induction accelerating modules, and multiple-beam hardware, at affordable costs; acceleration of multiple beams with current amplification --both new features in a linac -- without significant dilution of the optical quality of the beams; and final bunching, transport, and accurate focusing on a small target

  8. Heavy ion fusion accelerator research (HIFAR) year-end report, April 1, 1987-September 30, 1987

    1987-12-01

    The basic objective of the Heavy Ion Fusion Accelerator Research (HIFAR) program is to access the suitabilty of heavy ion accelerators as iginiters for Inertial Confinement Fusion (ICF). A specific accerelator techonolgy, the induction linac, has been studied at the Lawerence Berkeley Laboratory and has reached the point at which its viability for ICF applications can be assessed over the next few years. The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the vadidation of new accelerator strategies, to cut costs. The papers in this report that address these goals are: MBE-4 mechanical progress, alignment of MBE-4, a compact energy analyzer for MBE-4, Cs + injector modeling with the EGUN code, an improved emittance scanning system for HIFAR, 2-MV injector, carbon arc source development, beam combining in ILSE, emittance growth due to transverse beam combining in ILSE - particle simulation results, achromatic beam combiner for ILSE, additional elements for beam merging, quadrupole magnet design for ILSE, and waveforms and longitudinal beam-parameters for ILSE

  9. Research and Test Reactor Fuel Elements (RTRFE)

    Pace, Brett W.; Marinak, Edward A.

    1999-01-01

    BWX Technologies Inc. (BWXT) has experienced several production improvements over the past year. The homogeneity yields in 4.8 gU/cc U 3 Si 2 plates have increased over last year's already high yields. Through teamwork and innovative manufacturing techniques, maintaining high quality surface finishes on plates and elements is becoming easier and less expensive. Currently, BWXT is designing a fabrication development plan to reach a fuel loading of 9 gU/cc within 2 - 4 years. This development will involve a step approach requested by ANL to produce plates using U-8Mo at a loading of 6 gU/cc first and qualify the fuel at those levels. In achieving the goal of a very high-density fuel loading of 9 gU/cc, BWXT is considering employing several new, state of the art, ultrasonic testing techniques for fuel core evaluation. (author)

  10. Study on the prediction of soil heavy metal elements content based on visible near-infrared spectroscopy

    Liu, Jinbao; Zhang, Yang; Wang, Huanyuan; Du, Yichun

    2018-06-01

    The estimation of soils heavy metal content can reflect the impending surroundings of surface, which lays theoretical foundation for using covered vegetation to monitor environment and investigate resource. In this study, the contents of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb in 44 soil samples were collected from Fufeng County, Yangling County and Wugong County, Shaanxi Province and were used as data sources. ASD FieldSpec HR (350-2500 nm), and then the NOR, MSC and SNV of the reflectance were pretreated, the first deviation, second deviation and reflectance reciprocal logarithmic transformation were carried out. The optimal spectroscopy estimation model of nine heavy metal elements of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb was established by regression method. Comparing the diffuse reflectance characteristics of different heavy metal contents and the effect of different pretreatment methods on the establishment of soil heavy metal spectral inversion model. The results of chemical analysis show that there was a serious Hg pollution in the study area, and the Cd content was close to the critical value. The results show that: (1) NOR, MSC and SNV were adopted for the acquisition of visible near-infrared. Combining differential transformation can improve the information of heavy metal elements in the soil, and use the correlation band energy Significantly improve the stability and predictability of the model. (2) The modeling accuracy of the optimal model of nine heavy metal spectra of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb by PLSR method were 0.70, 0.79, 0.69, 0.81, 0.86, 0.58, 0.55, 0.99, 0.62. (3) The optimal estimation model of different elements using different treatment methods has better stability and higher precision, and can realize the rapid prediction of nine kinds of heavy metal elements in this region.

  11. Study on the prediction of soil heavy metal elements content based on visible near-infrared spectroscopy.

    Liu, Jinbao; Zhang, Yang; Wang, Huanyuan; Du, Yichun

    2018-06-15

    The estimation of soils heavy metal content can reflect the impending surroundings of surface, which lays theoretical foundation for using covered vegetation to monitor environment and investigate resource. In this study, the contents of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb in 44 soil samples were collected from Fufeng County, Yangling County and Wugong County, Shaanxi Province and were used as data sources. ASD FieldSpec HR (350-2500nm), and then the NOR, MSC and SNV of the reflectance were pretreated, the first deviation, second deviation and reflectance reciprocal logarithmic transformation were carried out. The optimal spectroscopy estimation model of nine heavy metal elements of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb was established by regression method. Comparing the diffuse reflectance characteristics of different heavy metal contents and the effect of different pretreatment methods on the establishment of soil heavy metal spectral inversion model. The results of chemical analysis show that there was a serious Hg pollution in the study area, and the Cd content was close to the critical value. The results show that: (1) NOR, MSC and SNV were adopted for the acquisition of visible near-infrared. Combining differential transformation can improve the information of heavy metal elements in the soil, and use the correlation band energy Significantly improve the stability and predictability of the model. (2) The modeling accuracy of the optimal model of nine heavy metal spectra of Cr, Mn, Ni, Cu, Zn, As, Cd, Hg and Pb by PLSR method were 0.70, 0.79, 0.69, 0.81, 0.86, 0.58, 0.55, 0.99, 0.62. (3) The optimal estimation model of different elements using different treatment methods has better stability and higher precision, and can realize the rapid prediction of nine kinds of heavy metal elements in this region. Copyright © 2018 Elsevier B.V. All rights reserved.

  12. Social research design: framework for integrating philosophical and practical elements.

    Cunningham, Kathryn Burns

    2014-09-01

    To provide and elucidate a comprehensible framework for the design of social research. An abundance of information exists concerning the process of designing social research. The overall message that can be gleaned is that numerable elements - both philosophical (ontological and epistemological assumptions and theoretical perspective) and practical (issue to be addressed, purpose, aims and research questions) - are influential in the process of selecting a research methodology and methods, and that these elements and their inter-relationships must be considered and explicated to ensure a coherent research design that enables well-founded and meaningful conclusions. There is a lack of guidance concerning the integration of practical and philosophical elements, hindering their consideration and explication. The author's PhD research into loneliness and cancer. This is a methodology paper. A guiding framework that incorporates all of the philosophical and practical elements influential in social research design is presented. The chronological and informative relationships between the elements are discussed. The framework presented can be used by social researchers to consider and explicate the practical and philosophical elements influential in the selection of a methodology and methods. It is hoped that the framework presented will aid social researchers with the design and the explication of the design of their research, thereby enhancing the credibility of their projects and enabling their research to establish well-founded and meaningful conclusions.

  13. Determination of Heavy Metals and Radioactive Elements in Alluvial Soil using Atomic Absorption and Gamma Spectroscopy

    Hamed, S.S.; Walley EI Dine, N.; Soliman, S.I.; Moussa, W.M.

    2008-01-01

    The paper describes some methods dealing with measurements of some heavy and radioactive elements (U, Th and K) in Egyptian cultivated soil samples. Samples were collected from Toshka area. Also, soil and plant samples were collected from Kalube and EI - Gabal EI - Asfar to compare the obtained results from both region. Flame atomic absorption spectrometry (FAAS),Neutron activation analysis (INAA) and Natural radioactivity techniques were followed. FAAS and INAA techniques agreed fairly well for the compared elements Co,Zn and Fe which determined by the two techniques. Also for K which was determined by FAAS and natural radioactivity. It was found that the concentration range in soil samples for Co, Fe, K and Zn lies between 4.18 and 29.2 μg/g, 3.0 and 3.8 mg/g, 3.49 and 13.28 mg/g and 120 and 663 μg/g respectively while in plant samples the concentration of Co was from 3.02 to 4.02 μg/g, Fe from 1.18 to 1.35 mg/g and Zn from 29.63 to 73.02 μg/g

  14. Clinical trial of cancer therapy with heavy ions at heavy ion research facility in lanzhou

    Zhang, Hong

    With collaborative efforts of scientists from the Institute of Modern Physics (IMP), Chinese Academy of Sciences and hospitals in Gansu, initial clinical trial on cancer therapy with heavy ions has been successfully carried out in China. From November 2006 to December 2007, 51 patients with superficially-placed tumors were treated with carbon ions at Heavy Ion Research Facility in Lanzhou (HIRFL) within four beam time blocks of 6-11 days, collaborating with the General Hospital of Lanzhou Command and the Tumor Hospital of Gansu Province. Patients and Methods: There were 51 patients (31 males and 20 females) with superficially-placed tumors (squamous cell carcinoma of the skin, basal cell carcinoma of the skin, malignant skin melanoma, sarcoma, lymphoma, breast cancer, metastatic lymph nodes of carcinomas and other skin lesions). The tumors were less than 2.1 cm deep to the skin surface. All patients had histological confirmation of their tumors. Karnofsky Performance Scale (KPS) of all patients was more than 70. The majority of patients were with failures or recurrences of conventional therapies. Median age at the time of radiotherapy (RT) was 55.5 years (range 5-85 years). Patients were immobilized with a vacuum cushion or a head mask and irradiated by carbon ion beams with energy 80-100 MeV/u at spread-out Bragg peak field generated from HIRFL, with two and three-dimensional conformal irradiation methods. Target volume was defined by physical palpation [ultrasonography and Computerized tomography (CT), for some cases]. The clinical target volume (CTV) was defined as the gross total volume GTV with a 0.5-1.0cm margin axially. Field placement for radiation treatment planning was done based on the surface markings. RBE of 2.5-3 within the target volume, and 40-75 GyE with a weekly fractionation of 7 × 3-15 GyE/fraction were used in the trial. Patients had follow-up examinations performed 1 month after treatment, in 1 or 2 months for the first 6 months, and 3

  15. Heavy metals effects on forage crops yields and estimation of elements accumulation in plants as affected by soil

    Grytsyuk, N.; Arapis, G.; Perepelyatnikova, L.; Ivanova, T.; Vynograds'ka, V.

    2006-01-01

    Heavy metals (Cu, Cd, Pb, Zn) effect on the productivity of forage crops (clover and perennial cereal grasses) and their accumulation in plants, depending on the concentration of these elements in a soil, has been studied in micro-field experiments on three types of soil. The principle objective was to determine regularities of heavy metals migration in a soil-plant system aiming the estimation of permissible levels of heavy metals content in soils with the following elaboration of methods, which regulate the toxicants transfer to plants. Methods of field experiments, agrochemical and atomic absorption analysis were used. Results were statistically treated by Statistica 6.0, S-Plus 6. Experimental results have shown that the intensity of heavy metals accumulation in plants depends on the type of the soil, the species of plants, the physicochemical properties of heavy metals and their content in the soil. Logarithmic interdependency of heavy metals concentration in soils and their accumulation in plants is suggested. However, the strong correlation between the different heavy metals concentrations in the various soils and the yield of crops was not observed. Toxicants accumulation in crops decreased in time

  16. Heavy metals effects on forage crops yields and estimation of elements accumulation in plants as affected by soil.

    Grytsyuk, N; Arapis, G; Perepelyatnikova, L; Ivanova, T; Vynograds'ka, V

    2006-02-01

    Heavy metals (Cu, Cd, Pb, Zn) effect on the productivity of forage crops (clover and perennial cereal grasses) and their accumulation in plants, depending on the concentration of these elements in a soil, has been studied in micro-field experiments on three types of soil. The principle objective was to determine regularities of heavy metals migration in a soil-plant system aiming the estimation of permissible levels of heavy metals content in soils with the following elaboration of methods, which regulate the toxicants transfer to plants. Methods of field experiments, agrochemical and atomic absorption analysis were used. Results were statistically treated by Statistica 6.0, S-Plus 6. Experimental results have shown that the intensity of heavy metals accumulation in plants depends on the type of the soil, the species of plants, the physicochemical properties of heavy metals and their content in the soil. Logarithmic interdependency of heavy metals concentration in soils and their accumulation in plants is suggested. However, the strong correlation between the different heavy metals concentrations in the various soils and the yield of crops was not observed. Toxicants accumulation in crops decreased in time.

  17. Workshop on environmental research for actinide elements

    Watters, R.L.

    1981-09-01

    The discussions in this fifth workshop were directed to the advances which have been made in the environmental chemistry of plutonium and to the feasibility and worth of developing environmental transport models which might serve as predictive tools for long term behavior and as guides for future research needs. Two plutonium models of the soil/plant pathway were presented for critique and as examples of possible approaches. Reports of the following four panels are presented in this proceedings: model development; marine; terrestrial and freshwater/groundwater

  18. Radionuclides and heavy elements containing in the soil and vegetation in the area of Didmay tailing pit

    Razikov, Z.A.; Yunusov, M.M.

    1997-01-01

    In this article on the base of carried out investigations authors made conclusion on effectiveness of obtaining of geo botanical methods of territory investigation adjoining to the tailing pits. With the purpose of decreasing of radionuclides and heavy metals concentration in the soil it was determined for this spot the plant-indicators and association which can accumulate radioactive and attendant them chemical elements

  19. X-ray spectroscopy of highly ionized heavy ions as an advanced research for controlled nuclear fusion power

    Zschornack, G.; Musiol, G.

    1988-01-01

    Diagnostics and modelling of nuclear fusion plasmas require a detailed knowledge of atomic and molecular data for highly ionized heavy ions. Experimental verification of atomic data is made on the basis of IAEA recommendations using the method of high-resolution wavelength-dispersive X-ray spectroscopy in order to obtain contributions extensioning the available atomic data lists. Basic facilities for producing highly charged heavy ions are the electron-ion rings of the heavy ion collective accelerator and the electron beam ion source KRYON-2 at the Joint Institute for Nuclear Research at Dubna. For high-resolution X-ray spectroscopy with these sources a computer-aided crystal diffraction spectrometer has been developed the precision of which is achieved by using advanced principles of measurement and control. Relativistic atomic structure calculations have been carried out for a great number of elements and configurations to obtain data in ionization regions heavily accessible to the experiment. (author)

  20. Research of the radiation effects distributing rule for electron element

    Yu Yanyin

    2004-01-01

    In this paper, the theory of testing way for statistical distribution is researched, and using the irradiation date on trial, application of Shapiro-wilk and construct way to radiation reinforce element checking and accepting is explained and authenticated. (authors)

  1. Determination of Heavy and Toxic Trace Elements in Sediments of Qarun Lake Using Instrumental Neutron Activation Analysis Technique

    Hamed, A.; Abd EI-Samad, M.; Soliman, N.F.

    2011-01-01

    An investigation of certain heavy and toxic trace elements in 15 sediment samples from different areas at Qarun Lake was performed by a neutron activation technique using the neutron irradiation facilities of the Second Egyptian Research Reactor (ETRR-2). The samples together with two sets of gold foils (one bare and the other covered with cadmium) and two Standard Reference Materials IAEA (Soil-7) were irradiated at the core of the reactor in two capsules for 8520 seconds, another two capsules each has two sets of gold foils (one bare and the other covered with cadmium) are used to determine the neutron fluxes around the sediment samples. The gamma-rays of nuclides from the irradiated samples were carried out by means of a well calibrated high resolution HPGe detection system. The concentrations of product nuclides containing in the irradiated samples were determined from the peak counting-rates of the prominent gamma-ray lines for the corresponding nuclides using Single External Comparator Method (k 0 -Standardization Method) which called k 0 -NAA technique. The neutron flux ratios (f) in the same radiation sites of the sediment samples bottles were calculated as well as the cadmium ratios (R e d). MS Excel work books were constructed and used in our calculation. The total contents of As , Ba , Ca ,Co, Cr ,Cs, Eu ,Hf ,Hg,Na ,Ru ,Sc ,Se ,Sm ,Sn ,Sr ,Th ,Rb ,Zn ,and Zr in these samples were measured. The objectives .of this study were evaluated to identify the variations of concentration of some elements that have an impact on environmental pollutions. The results indicated that the concentrations of toxic trace elements of Ba, Cr, Se, Sn, Hg, Sin and Zn may represent pollutions problem

  2. Status and prospect of super-heavy nuclei research at IMP

    Xu Hushan; Sun Zhiyu; Zhan Wenlong; Zhou Xiaohong; Huang Wenxue; Zhang Hongbin; Gan Zaiguo; Li Junqing; Ma Xinwen; Qin Zhi; Xiao Guoqing; Guo Zhongyan; Li Zhihui; Zhang Yuhu; Jin Genming; Huang Tianheng; Hu Zhengguo; Zhang Xueheng; Zheng Chuan; Chinese Academy of Sciences, Beijing

    2006-01-01

    The history and the international status of the super-heavy nuclei synthesis are briefly described. The related research work carried out at the Institute of Modern Physics (IMP) has been reviewed. The prospect of the super-heavy nuclei research at IMP has been introduced. (authors)

  3. Summary talk at the symposium on relativistic heavy ion research G.S.I., Darmstadt, Germany

    Grunder, H.A.

    1978-03-01

    Ideas expressed at the symposium and the general state of relativistic heavy-ion research are reviewed. The relationship with biology and medicine and with fusion is addressed. What has been learned about heavy ions and suggested possible next research steps are tabulated. 3 figures, 4 tables

  4. Origin of the heavy elements in binary neutron-star mergers from a gravitational-wave event.

    Kasen, Daniel; Metzger, Brian; Barnes, Jennifer; Quataert, Eliot; Ramirez-Ruiz, Enrico

    2017-11-02

    The cosmic origin of elements heavier than iron has long been uncertain. Theoretical modelling shows that the matter that is expelled in the violent merger of two neutron stars can assemble into heavy elements such as gold and platinum in a process known as rapid neutron capture (r-process) nucleosynthesis. The radioactive decay of isotopes of the heavy elements is predicted to power a distinctive thermal glow (a 'kilonova'). The discovery of an electromagnetic counterpart to the gravitational-wave source GW170817 represents the first opportunity to detect and scrutinize a sample of freshly synthesized r-process elements. Here we report models that predict the electromagnetic emission of kilonovae in detail and enable the mass, velocity and composition of ejecta to be derived from observations. We compare the models to the optical and infrared radiation associated with the GW170817 event to argue that the observed source is a kilonova. We infer the presence of two distinct components of ejecta, one composed primarily of light (atomic mass number less than 140) and one of heavy (atomic mass number greater than 140) r-process elements. The ejected mass and a merger rate inferred from GW170817 imply that such mergers are a dominant mode of r-process production in the Universe.

  5. In vivo XRF measurements of heavy elements: Summary of a workshop

    Wielopolski, L.; Ryon, R.W.

    1995-01-01

    This is a brief summary of the first workshop of open-quotes In Vivo XRF Measurements of Heavy Elements,close quotes at the Denver Conference on Applications of X-Ray Analysis. In vivo x-ray fluorescence has been applied to medical applications since the 1960's, with much of the pioneering work being done in Sweden (1). First measurements were of iodine in the thyroid. Elements from iron ID uranium have now been measured, at natural and elevated levels. Elevated levels occur either unintentionally through occupational or environmental exposure, or intentionally through medical administration. Examples of measurements are cadmium in kidney and liver, platinum in kidneys and tumors, mercury in the wrists and skulls of dentists, lead in various near-surface bones, copper in the eye and iron in skin. Nearly all measurements make use of either silicon or germanium detectors; radioisotopes and less frequently x-ray tubes are used for excitation. One question that those who work in an analytical chemistry laboratory often ask concerns radiation doses. Concern for x-ray safety ordinarily precludes putting living subjects into the x-ray beam. It turns out that radiation exposure due to in vivo x-ray fluorescence is quite low. The effective dose values for measurement of tibia lead concentration using a 109 Cd source (30 minute exposure) ranges from 0.036 uSv for adults to 1.1 uSv for infants (less than one tenth of a single dental x-ray) (2). Lower effective doses were reported when an x-ray machine was Used to measure L x-rays (3). These values are far below proposed limits of negligibility (10 USv) and average annual U.S. natural background radiation (3000 uSv). 17 refs

  6. Marine Phosphorites as Potential Resources for Heavy Rare Earth Elements and Yttrium

    James R. Hein

    2016-08-01

    Full Text Available Marine phosphorites are known to concentrate rare earth elements and yttrium (REY during early diagenetic formation. Much of the REY data available are decades old and incomplete, and there has not been a systematic study of REY distributions in marine phosphorite deposits that formed over a range of oceanic environments. Consequently, we initiated this study to determine if marine phosphorite deposits found in the global ocean host REY concentrations of high enough grade to be of economic interest. This paper addresses continental-margin (CM and open-ocean seamount phosphorites. All 75 samples analyzed are composed predominantly of carbonate fluorapatite and minor detrital and authigenic minerals. CM phosphorites have low total REY contents (mean 161 ppm and high heavy REY (HREY complements (mean 49%, while seamount phosphorites have 4–6 times higher individual REY contents (except for Ce, which is subequal; mean ΣREY 727 ppm, and very high HREY complements (mean 60%. The predominant causes of higher concentrations and larger HREY complements in seamount phosphorites compared to CM phosphorites are age, changes in seawater REY concentrations over time, water depth of formation, changes in pH and complexing ligands, and differences in organic carbon content in the depositional environments. Potential ore deposits with high HREY complements, like the marine phosphorites analyzed here, could help supply the HREY needed for high-tech and green-tech applications without creating an oversupply of the LREY.

  7. Uranium fluoride and metallic uranium as target materials for heavy-element experiments at SHIP

    Kindler, Birgit [Gesellschaft fuer Schwerionenforschung (GSI), Planckstrasse 1, D-64291 Darmstadt (Germany)], E-mail: b.kindler@gsi.de; Ackermann, Dieter; Hartmann, Willi; Hessberger, Fritz Peter; Hofmann, Sigurd; Huebner, Annett; Lommel, Bettina; Mann, Rido; Steiner, Jutta [Gesellschaft fuer Schwerionenforschung (GSI), Planckstrasse 1, D-64291 Darmstadt (Germany)

    2008-06-01

    In this contribution we describe the production and application of uranium targets for synthesis of heavy elements. The targets are prepared from uranium fluoride (UF{sub 4}) and from metallic uranium with thin carbon foils as backing. Targets of UF{sub 4} were produced by thermal evaporation in a similar way as the frequently applied targets out of Bi, Bi{sub 2}O{sub 3}, Pb, PbS, SmF{sub 3}, and NdF{sub 3,} prepared mostly from isotopically enriched material [Birgit Kindler, et al., Nucl. Instr. and Meth. A 561 (2006) 107; Bettina Lommel, et al., Nucl. Instr. and Meth. A 561 (2006) 100]. In order to use more intensive beams and to avoid scattering of the reaction products in the target, metallic uranium is favorable. However, evaporation of metallic uranium is not feasible at a sustainable yield. Therefore, we established magnetron sputtering of metallic uranium. We describe production and properties of these targets. First irradiation tests show promising results.

  8. Heavy metal elements in toiletries analyzed by INAA, ICP-MS and SEM-EDX

    Furuta, E.; Tagami, K.; Okada, Y.; Nakahara, H.

    2011-01-01

    Recently, many toiletries claiming inclusion of platinum (Pt), silver (Ag) and gold (Au) as additives are sold in ordinary cosmetics shops. However, their concentrations are not clearly indicated. In the present work, these toiletries were analyzed for heavy metal elements by instrumental neutron activation analysis (INAA) and inductively coupled plasma mass spectrometry (ICP-MS), and the particle sizes were observed by scanning electron microscope (SEM) and the constitutions of the small particles were analyzed by energy dispersive X-ray spectroscopy (EDX). The concentrations of Pt in the toiletries observed were from 1 to 80 ppm. The lower detection limit of Pt by INAA was about 1 ppm because of the presence of sodium in high concentrations for those samples. Consequently, some toiletries which should have had Pt according to the manufactures were found not to contain Pt probably because it was less than the detection limit. On the other hand, there were a few toiletries that were found to contain Ag although the addition of Ag was not mentioned by the manufactures. It is considered that these non-indicated Ag were included as impurities of the added Au. The concentrations of the non-indicated Ag were even higher than those of the indicated Ag. A very small amount of Sr, which was nominated in the negative list of Japan, was also detected in 2 out of 5 kinds of toiletries analyzed by ICP-MS. (orig.)

  9. Measurements of Plutonium isotopes and the search for super-heavy elements via AMS

    Wallner, A.; Steier, P.; Golser, R.; Knie, K.; Kutschera, W.; Priller, A.; Hrnecek, E.; Jakopic, R.; Korschinek, G.

    2006-01-01

    Full text: Accelerator Mass Spectrometry (AMS) - being independent on the half-life of a radionuclide - provides a technique to determine isotope ratios with the highest sensitivity and allows the measurement of radionuclides over a wide dynamic range of concentration levels. A combination of AMS, Alpha Spectrometry and Liquid Scintillation Counting was used for the determination of the complete information on isotope ratios of Plutonium isotopes in different environmental reference samples (e.g. from the atolls of Mururoa and Fangataufa) and samples contaminated from nuclear reprocessing. Results for the isotopic ratios of the samples will be shown and the capabilities and detection limits achievable for determination of Pu will be discussed. The long-lived 244 Pu (t 1/2 = 80 Ma) and 247 Cm (t 1/2 = 15.6 Ma) have a very interesting application in astrophysics by detecting possible supernova-produced 244 Pu and 247 Cm in terrestrial archives. The expected extremely small concentrations of 244 Pu makes AMS the favorite method. The actual search for such long-lived extraterrestrial radionuclides and possible implications will be presented. The same method has also been explored for a pinprick-search of long-lived super-heavy elements in the mass region above Z=100. (author)

  10. Progress of pharmacogenomic research related to minerals and trace elements.

    Zeng, Mei-Zi; Tang, Jie; Liu, Zhao-Qian; Zhou, Hong-Hao; Zhang, Wei

    2015-10-01

    Pharmacogenomics explores the variations in both the benefits and the adverse effects of a drug among patients in a target population by analyzing genomic profiles of individual patients. Minerals and trace elements, which can be found in human tissues and maintain normal physiological functions, are also in the focus of pharmacogenomic research. Single-nucleotide polymorphisms (SNPs) affect the metabolism, disposition and efficacy of minerals and trace elements in humans, resulting in changes of body function. This review describes some of the recent progress in pharmacogenomic research related to minerals and trace elements.

  11. Research on heavy oil degradation by four thermophilic bacterial strains

    Bao, M.; Chen, Q.; Liu, Z.; Li, Y. [Ocean Univ. of China, Qingdao, Shandong (China)

    2009-07-01

    The Shengli oilfield is the second largest onshore oil field in China, with a crude oil output of approximately 30 million tons per year. The large quantities of wastewater that are produced during thermal recovery methods have posed a challenge in terms of water reuse, reinjection and discharge. The important aspect of wastewater treatment is the removal of residual heavy oil. Biological methods are considered to be efficient in solving this problem. This paper reported on a study in which 4 thermophilic microorganisms which had the ability to biodegrade heavy oil were screened from heavy oil wastewater in the Shengli oilfield. Their degradation to heavy oil was discussed and the suitable biodegradation conditions of these bacteria were investigated. The study showed that the degrading efficiency of heavy oil by the 4 bacteria was up to 42.0, 47.6, 55.6 and 43.4 per cent in the wastewater which contained 500 mg per litre of heavy oil, respectively. The crude oil samples were analyzed using gas chromatography/flame ionization detection (GC/FID) and gas chromatography/mass spectrometry (GC/MS) before and after degradation. The single 4 strains demonstrated strong biodegradability to normal alkanes and aromatics, and the average degrading efficiency was about 50 and 35 per cent. The degrading efficiency of the mixed 4 strains was better than the single ones, particularly for the poor biodegradable hydrocarbons such as phenanthrenes and fluorines. 21 refs., 2 tabs., 17 figs.

  12. Radiation characteristics of spent fuel of heavy-water research reactor during long-term storage

    Gerasimov, A.S.; Kiselev, G.V.; Myrtsymova, L.A.; Zaritskaya, T.S.

    2002-01-01

    Decay heat power and radiotoxicity by water of actinides and fission products from spent fuel of heavy-water research reactor RA were calculated for period of storage during 300000 years. Three variants of fuel enrichment by 235 U were considered: 2%, 21%, and 80%. The mass of 235 U in one fuel element was supposed to be the same for all variants of enrichment. The decay heat power of fission products in initial period is about 20 times higher than that of actinides. Decay heat power and radiotoxicity of actinides do not practically decrease during long period of time as they are determined by nuclides with very long half-life periods. (author)

  13. Trace elements in land plants: concentration ranges and accumulators of rare earths, Ba, Ra, Mn, Fe, Co, and heavy halogens

    Koyama, Mutsuo; Shirakawa, Masahiro; Takada, Jitsuya; Katayama, Yukio; Matsubara, Takashi

    1986-01-01

    More than 2000 samples of land plant leaves, mostly of tree, have been analysed by neutron activation analysis in order to find out macroscopic relations between distributions of chemical elements in plants and soil characteristics. The distributions of the elements in plants were also examined from the view point of botanical taxonomy or phylogeny. New species which accumulate Co, rare earths, Ba, Ra, heavy halogens and other elements have been found. Capability or potentiality for accumulating elements could be related to primarily to species. In several cases, however, it is related to higher ranks of taxonomy, that is, genus or family. The nature of soil is also found to have profound effects on the extent of accumulation of elements in plants. (author)

  14. Nuclear research with heavy ions. Annual progress report, January 1, 1981-December 31, 1981

    Kaplan, M.

    1981-11-01

    The experimental research program is primarily concerned with the nuclear reactions induced by collisions between heavy-ion projectiles and complex target nuclei, the dynamics and thermodynamics associated with such collisions, and the relationships of the observables to the equilibrium and non-equilibrium properties of nuclear matter. As a sensitive probe of the nuclear interactions, detailed measurements of light-charged-particle emission were performed using counter telescopes for atomic number and mass number identification. Preliminary results from a new experiment on direct and evaporation-like emission of 4 He from reactions of 340-MeV 40 Ar with 238 U are reported. Using a large two-dimensional position-sensitive avalanche detector, and measuring three-fold coincidence events between two fission fragments and an emitted 4 He particle, we were able to distinguish emission processes in fusion-like fission from those associated with inelastic reactions. Analysis of the data shows isotropic and strongly forward-peaked 4 He components for both fusion and sequential fission, and kinematic evidence indicates substantial evaporation-like emission from the composite system rather than from fission fragments. The effects of light element impurities on charged particle spectra from heavy ion collisions are discussed, and a technique for directly evaluating the impurity contribution is briefly described

  15. Nuclear criticality assessment of Oak Ridge research fuel element storage

    Thomas, J.T.

    1978-06-01

    Spent and partially spent Oak Ridge Research Reactor (ORR) fuel elements are retained in the storage section of the ORR pool facility. Determination of a maximum expected neutron multiplication factor for the storage area is accomplished by a validated calculational method. The KENO Monte Carlo code and the Hansen-Roach 16-group neutron cross section sets were validated by calculations of critical experiments performed with early ORR fuel elements and with SPERT-D fuel elements. Calculations of various fuel element arrangements are presented which confirm the subcriticality previously inferred from critical experiments and indicate the k/sub eff/ would not exceed 0.85, were the storage area to be filled to capacity with storage racks containing elements with the fissionable material loading increased to 350 g of 235 U

  16. The effects of fuel characteristics and engine operating conditions on the elemental composition of emissions from heavy duty diesel buses

    M.C.H. Lim; G.A. Ayoko; L. Morawska; Z.D. Ristovski; E.R. Jayaratne [Queensland University of Technology, Brisbane, Qld. (Australia). International Laboratory for Air Quality and Health, School of Physical and Chemical Sciences

    2007-08-15

    The effects of fuel characteristics and engine operating conditions on elemental composition of emissions from twelve heavy duty diesel buses have been investigated. Two types of diesel fuels - low sulfur diesel (LSD) and ultra low sulfur diesel (ULSD) fuels with 500 ppm and 50 ppm sulfur contents respectively and 3 driving modes corresponding to 25%, 50% and 100% power were used. Elements present in the tailpipe emissions were quantified by inductively coupled plasma mass spectrometry (ICPMS) and those found in measurable quantities included Mg, Ca, Cr, Fe, Cu, Zn, Ti, Ni, Pb, Be, P, Se, Ti and Ge. Multivariate analyses using multi-criteria decision making methods (MCDM), principal component analysis (PCA) and partial least squares (PLS) facilitated the extraction of information about the structure of the data. MCDM showed that the emissions of the elements were strongly influenced by the engine driving conditions while the PCA loadings plots showed that the emission factors of the elements were correlated with those of other pollutants such as particle number, total suspended particles, CO, CO{sub 2} and NOx. Partial least square analysis revealed that the emission factors of the elements were strongly dependent on the fuel parameters such as the fuel sulfur content, fuel density, distillation point and cetane index. Strong correlations were also observed between these pollutants and the engine power or exhaust temperature. The study provides insights into the possible role of fuel sulfur content in the emission of inorganic elements from heavy duty diesel vehicles. 39 refs., 1 fig., 4 tabs.

  17. Nuclear physics research requirements for electron and heavy ion machines

    Vogt, E.

    1983-03-01

    There has been a great deal of interest in a variety of new machines intended to probe atomic nuclei for hadronic and quark aspects which lie beyond the familiar shell model view of nuclei. This paper gives the physics perspective within which the proposals for such machines have arisen and discusses the two classes of tools - high energy cw electron machines and relativistic heavy ion machines - which lie at opposite ends of the arsenal being gathered for the pursuit of QCD in nuclei. The electron machines present a reasoned analytic approach to the simplest systems and the heavy ion machines a major thrust for starting new physics in the quark-gluon sea

  18. High-entropy ejections from magnetized proto-neutron star winds: implications for heavy element nucleosynthesis

    Thompson, Todd A.; ud-Doula, Asif

    2018-06-01

    Although initially thought to be promising for production of the r-process nuclei, standard models of neutrino-heated winds from proto-neutron stars (PNSs) do not reach the requisite neutron-to-seed ratio for production of the lanthanides and actinides. However, the abundance distribution created by the r-, rp-, or νp-processes in PNS winds depends sensitively on the entropy and dynamical expansion time-scale of the flow, which may be strongly affected by high magnetic fields. Here, we present results from magnetohydrodynamic simulations of non-rotating neutrino-heated PNS winds with strong dipole magnetic fields from 1014 to 1016 G, and assess their role in altering the conditions for nucleosynthesis. The strong field forms a closed zone and helmet streamer configuration at the equator, with episodic dynamical mass ejections in toroidal plasmoids. We find dramatically enhanced entropy in these regions and conditions favourable for third-peak r-process nucleosynthesis if the wind is neutron-rich. If instead the wind is proton-rich, the conditions will affect the abundances from the νp-process. We quantify the distribution of ejected matter in entropy and dynamical expansion time-scale, and the critical magnetic field strength required to affect the entropy. For B ≳1015 G, we find that ≳10-6 M⊙ and up to ˜10-5 M⊙ of high-entropy material is ejected per highly magnetized neutron star birth in the wind phase, providing a mechanism for prompt heavy element enrichment of the universe. Former binary companions identified within (magnetar-hosting) supernova remnants, the remnants themselves, and runaway stars may exhibit overabundances. We provide a comparison with a semi-analytic model of plasmoid eruption and discuss implications and extensions.

  19. A Review of Laboratory-Scale Research on Upgrading Heavy Oil in Supercritical Water

    Ning Li

    2015-08-01

    Full Text Available With the growing demand for energy and the depletion of conventional crude oil, heavy oil in huge reserve has attracted extensive attention. However, heavy oil cannot be directly refined by existing processes unless they are upgraded due to its complex composition and high concentration of heteroatoms (N, S, Ni, V, etc.. Of the variety of techniques for heavy oil upgrading, supercritical water (SCW is gaining popularity because of its excellent ability to convert heavy oil into valued, clean light oil by the suppression of coke formation and the removal of heteroatoms. Based on the current status of this research around the world, heavy oil upgrading in SCW is summarized from three aspects: Transformation of hydrocarbons, suppression of coke, and removal of heteroatoms. In this work, the challenge and future development of the orientation of upgrading heavy oil in SCW are pointed out.

  20. HAT-P-26b: A Neptune-mass exoplanet with a well-constrained heavy element abundance.

    Wakeford, Hannah R; Sing, David K; Kataria, Tiffany; Deming, Drake; Nikolov, Nikolay; Lopez, Eric D; Tremblin, Pascal; Amundsen, David S; Lewis, Nikole K; Mandell, Avi M; Fortney, Jonathan J; Knutson, Heather; Benneke, Björn; Evans, Thomas M

    2017-05-12

    A correlation between giant-planet mass and atmospheric heavy elemental abundance was first noted in the past century from observations of planets in our own Solar System and has served as a cornerstone of planet-formation theory. Using data from the Hubble and Spitzer Space Telescopes from 0.5 to 5 micrometers, we conducted a detailed atmospheric study of the transiting Neptune-mass exoplanet HAT-P-26b. We detected prominent H 2 O absorption bands with a maximum base-to-peak amplitude of 525 parts per million in the transmission spectrum. Using the water abundance as a proxy for metallicity, we measured HAT-P-26b's atmospheric heavy element content ([Formula: see text] times solar). This likely indicates that HAT-P-26b's atmosphere is primordial and obtained its gaseous envelope late in its disk lifetime, with little contamination from metal-rich planetesimals. Copyright © 2017, American Association for the Advancement of Science.

  1. Application of laplace transform method in heavy ion reaction research

    Wang Jinchuan; Xi Hongfei; Guo Zhongyan; Zhan Wenlong; Zhu Yongtai; Zhou Jianqun; Liu Guanhua

    1993-01-01

    Laplace transform method (LTM) is applied to investigate the effects of different spectroscopy amplifiers parameters on identification of the light charged particles (LCP) emitted from 12 C(46,7 MeV/u) + 58 Ni reaction. The significance of application of LTM in heavy ion experimental nuclear physics is also discussed

  2. Ultrasonic evaluation of end cap weld joints of fuel elements of pressurized heavy water reactors using signal analysis methods

    Raj, B.; Thavasimuthu, M.; Subramanian, C.V.; Kalyanasundaram, P.; Rajagopalan, C.

    1992-01-01

    This paper describes the application of ultrasonic digital signal analysis for the detection of fine defects of the order of 10% or lower of wall thickness (WT) of 370 microns in the resistance welded end cap-cladding tube joints of fuel elements used in Pressurised Heavy Water Reactors (PHWR s). The results obtained for the detection of such defects, have confirmed the sensitivity and reliability of this approach, and were further validated by destructive metallography. (author)

  3. Reactor physics measurements with 19-element ThOsub(2)-sup(235)UOsub(2) cluster fuel in heavy water moderator

    French, P.M.

    1985-02-01

    Low power lattice physics measurements have been performed with a single rod of 19-element thorium oxide fuel enriched with 1.45 wt. percent sub(235)UOsub(2) (93 percent enriched) in a simulated heavy water moderated and cooled power reactor core. The experiments were designed to provide data relevant to a power reactor irradiation and to obtain some basic information on the physics of uranium-thorium fuel material. Some theoretical flux calculations are summarized and show reasonable agreement with experiment

  4. Common data elements for spinal cord injury clinical research

    Biering-Sørensen, F; Alai, S; Anderson, K.

    2015-01-01

    Institutes of Health. SETTING: International Working Groups. METHODS: Nine working groups composed of international experts reviewed existing CDEs and instruments, created new elements when needed and provided recommendations for SCI clinical research. The project was carried out in collaboration...... of CDEs can facilitate SCI clinical research and trial design, data sharing and retrospective analyses. Continued international collaboration will enable consistent data collection and reporting, and will help ensure that the data elements are updated, reviewed and broadcast as additional evidence......OBJECTIVES: To develop a comprehensive set of common data elements (CDEs), data definitions, case report forms and guidelines for use in spinal cord injury (SCI) clinical research, as part of the CDE project at the National Institute of Neurological Disorders and Stroke (NINDS) of the US National...

  5. Distribution of Heavy Metal Elements in the Sea Water, Algae and Fish ofMuria Peninsula Area

    Djati-Pramana, J; Agus-Taftazani; Sudarmadji

    2000-01-01

    Analysis of heavy metal elements in the specimens of sea water, brownalgae and kerapu fish from two area sampling Lemah Abang and Semat beach byINAA method was done. The same of such specimens from Krakal beach was takenfor control specimen. The aim of this investigation was to obtain a part ofinput data for EMSB program. Preparation after sampling was performed asfollows. Sea water sample was concentrated using 1/5 times of the initialvolume. Algae and fish specimens were crushed using N 2 liquid, dried at thefreeze dryer than were homogenized and screened through 100 mesh. The threeof those specimens were irradiated together for 12 hours in the Lazy Susanirradiation facility of Kartini reactor. Flux neutron was 5.85 . 10 10 n/cm 2 .sec. The heavy metal elements that could be identified were Sm, Se,Cr, Zr, Fe and Co. Concentration in the specimens from Muria peninsula wasrelatively higher comparated to control specimens. This might be use to thefound of these indicators to concentrated that of heavy metals from sea wateror their environment which has a higher concentration. From t test for 95 %probability to control specimens was showed that these was a significantdifference from all the detected elements. From the obtained data there was apollution indication in the area at the period of sampling. (author)

  6. Determination of trace element and heavy metal in black tea and tea leaves using x-ray fluorescence

    Salih, Mohamed Abualgasim Abdalhakam

    2016-08-01

    The aim of this study was to provide information about the trace element and heavy metals concentrations in black tea and tea leaves. 23 different samples were collected from the Sudanese local market. The collected samples were characterized as the most common used items in Sudan. The concentration of trace and heavy elements were determined using x-ray fluorescence (X RF) technique. The standard reference materials (IAEA-V-10) and hay (powder) were used to evaluate the accuracy of the analytical result. The measured values were found in agreement with the certified values. The elements determined were K, Ca, Cr, Mn, Fe, Ni, Cu, Zn, Pb, Br, Rb, and Sr. The average concentration of the elements is black tea were 2277.43, 7245.71, 1.11, 1025.29, 334.29, 6.88, 11.24, 9.47, 1.02, 7.08, 97.4 and 63.21 respectively while the average concentration of the elements in leaves tea were 2644.44, 8805.56, 1.02, 571.81, 295.44, 6.19, 10.69, 9.26, 0.91, 13.42, 63.03 and 67.14 respectively. The results showed an increase in the concentration of some elements such as calcium, chromium, manganese, iron, nickel, copper, zinc, bromine, rubidium and strontium (22500, 6.75, 48.9, 194, 4.37, 9,77, 24.9, 8.23, 7.79, 40,9) ppm respectively compared to certified values. Correlation between concentration of certain element and cluster analysis were preformed and the results compared with values of literature and the concentrations of some elements found to be similar.(Author)

  7. Reducing Heavy Metal Element from Coal Bottom Ash by Using Citric Acid Leaching Treatment

    Yahya Ahmad Asyari

    2017-01-01

    Full Text Available Coal ash is the residue that is produced during coal combustion for instance fly ash, bottom ash or boiler slag which was primarily produced from the combustion of coal. With growth in coal burning power station, huge amount of coal bottom ash (CBA considered as hazardous material which are normally disposed in an on-site disposal system without any commercialization purpose. Previous researchers have studied the extraction of silica from agricultural wastes such as palm ash and rice husk ash (RHA and CBA by using leaching treatment method. In this study, the weaker acid, citric acid solution was used to replace the strong acid in leaching treatment process. Result showed that the heavy metal content such as Copper (Cu, Zinc (Zn and Lead (Pb can be decrease. Meanwhile the silica can be extracted up to 44% from coal bottom ash using citric acid leaching treatment under the optimum reaction time of 60 minutes with solution temperature of 60°C and concentration of citric acid more than 2%.

  8. [Heavy metal pollution ecology of macro-fungi: research advances and expectation].

    Zhou, Qi-xing; An, Xin-long; Wei, Shu-he

    2008-08-01

    Macro-fungi are the main component of biosphere and one of the ecological resources, and play very important roles in matter cycling and in maintaining ecological balances. This paper summarized and reviewed the research advances in the eco-toxicological effects of heavy metals on macro-fungi, the bioaccumulation function of macro-fungi on heavy metals, the ecological adaptation mechanisms of macro-fungi to heavy metal pollution, the role of macro-fungi as a bio-indicator of heavy metal pollution, and the potential of macro-fungi in the ecological remediation of contaminated environment. To strengthen the researches on the heavy metal pollution ecology of macro-fungi would be of practical significance in the reasonable utilization of macro-fungi resources and in the ecological remediation of contaminated environment.

  9. [Comparison of heavy metal elements between natural and plantation forests in a subtropical Montane forest].

    Nie, Ming; Wan, Jia-Rong; Chen, Xiao-Feng; Wang, Li; Li, Bo; Chen, Jia-Kuan

    2011-11-01

    Heavy metals as one of major pollutants is harmful to the health of forest ecosystems. In the present paper, the concentrations of thirteen heavy metals (Fe, Al, Ti, Cr, Cu, Mn, V, Zn, Ni, Co, Pb, Se and Cd) were compared between natural and plantation forests in the Mt. Lushan by ICP-AES and atomic absorption spectroscopy. The results suggest that the soil of natural forest had higher concentrations of Fe, Al, Ti, Cu, Mn, V, Zn, Ni, Co, Pb, Se, and Cd than the plantation forest except for Cr. The soil of natural forest had a higher level of heavy metals than that of the plantation forest as a whole. This might be due to that the natural forest has longer age than the plantation forest, and fixed soil heavy metals take a longer period of time than the plantation forest.

  10. Elements to be considered in planning heavy ion fusion program: a summary

    Bohachevsky, I.O.

    1978-01-01

    A summary of Battelle's Engineering Development Program Plan for inertial confinement fusion is presented. Included are development objectives, facilities to achieve these objectives, program strategies, and a discussion of heavy-ion driver development

  11. Validity of M-3Y force equivalent G-matrix elements for calculations of the nuclear structure in heavy mass region

    Cheng Lan; Huang Weizhi; Zhou Baosen

    1996-01-01

    Using the matrix elements of M-3Y force as the equivalent G-matrix elements, the spectra of 210 Pb, 206 Pb, 206 Hg and 210 Po are calculated in the framework of the Folded Diagram Method. The results show that such equivalent matrix elements are suitable for microscopic calculations of the nuclear structure in heavy mass region

  12. MODAL ANALYSIS OF CARRIER SYSTEM FOR HEAVY HORIZONTAL MULTIFUNCTION MACHINING CENTER BY FINITE ELEMENT METHOD

    Yu. V. Vasilevich

    2014-01-01

    Full Text Available The aim of the paper is to reveal and analyze resonance modes of a large-scale milling-drilling-boring machine. The machine has a movable column with vertical slot occupied by a symmetrical carriage with horizontal ram. Static rigidity of the machine is relatively low due to its large dimensions. So it is necessary to assess possible vibration activity. Virtual and operational trials of the machine have been carried out simultaneously. Modeling has been executed with the help of a finite element method (FEM. The FEM-model takes into account not only rigidity of machine structures but also flexibility of bearings, feed drive systems and guides. Modal FEM-analysis has revealed eight resonance modes that embrace the whole machine tool. They form a frequency interval from 12 to 75 Hz which is undesirable for machining. Three closely located resonances (31-37 Hz are considered as the most dangerous ones. They represent various combinations of three simple motions: vertical oscillations of a carriage, horizontal vibrations of a ram and column torsion. Reliability of FEM- estimations has been proved by in-situ vibration measurements.An effect for stabilization of resonance modes has been detected while making variations in design parameters of the machine tool. For example, a virtual replacement of cast iron for steel in machine structures practically does not have any effect on resonance frequencies. Rigidity increase in some parts (e.g. a ram has also a small effect on a resonance pattern. On the other hand, resonance stability makes it possible to avoid them while selecting a spindle rotation frequency.It is recommended to set double feed drives for all axes. A pair of vertical screws prevents a “pecking” resonance of the carriage at frequency of 54 Hz. It is necessary to foresee an operation of a main drive of such heavy machine tool in the above resonance interval with the spindle frequency of more than 75 Hz. For this purpose it is necessary

  13. FINITE ELEMENT ANALYSIS OF CONCRETE FILLER INFLUENCE ON DYNAMIC RIGIDITY OF HEAVY MACHINE TOOL PORTAL

    Yu. V. Vasilevich

    2016-01-01

    Full Text Available Virtual testing of portal machine tool has been carried out with the help of finite elements method (FEM. Static, modal and harmonic analyses have been made for a heavy planer. The paper reveals influence of concrete filler on machine tool dynamic flexibility. A peculiar feature of the simulation is concrete filling of a high-level transverse beam. Such approach oes look a typical one for machine-tool industry. Concrete has been considered as generalized material in two variants. It has been established that concrete application provides approximately 3-fold increase in machine tool rigidity per each coordinate. In this regard it is necessary to arrange closure of rigidity contour by filling all the cavities inside of the portal. Modal FEA makes it possible to determine that concrete increases comparatively weakly (1.3–1.4-fold frequencies of resonance modes. Frequency of the lowest mode rises only from 30.25 to 42.86 Hz. The following most active whole-machine eigenmodes have been revealed in the paper: “Portal pecking”, “Parallelogram” and “Traverse pecking”. In order to restrain the last mode it is necessary to carry out concrete filling of the traverse, in particular. Frequency-response characteristics and curves of dynamic rigidity for a spindle have been plotted for 0–150 Hz interval while using harmonic FEM. It has been determined that concrete increases dynamic machine tool rigidity by 2.5–3.5-fold. The effect is obtained even in the case when weakly damping concrete (2 % is used. This is due to distribution of vibrational energy flow along concrete and along cast iron as well. Thus energy density and vibration amplitudes must decrease. The paper shows acceptability for internal reinforcement of high-level machine tool parts (for example, portal traverses and fillers are applied for this purpose. Traverse weighting is compensated by additional torsional, shear and bending rigidity. The machine tool obtains the

  14. Heavy rare earth elements affect early life stages in Paracentrotus lividus and Arbacia lixula sea urchins

    Oral, Rahime; Pagano, Giovanni; Siciliano, Antonietta; Gravina, Maria; Palumbo, Anna; Castellano, Immacolata; Migliaccio, Oriana; Thomas, Philippe J.; Guida, Marco; Tommasi, Franca; Trifuoggi, Marco

    2017-01-01

    Background: Heavy rare earth elements (HREEs) have been scarcely studied for their toxicity, in spite of their applications in several technologies. Thus HREEs require timely investigations for their adverse health effects. Methods: Paracentrotus lividus and Arbacia lixula embryos and sperm were exposed to trichloride salts of five HREEs (Dy, Ho, Er, Yb and Lu) and to Ce(III) as a light REE (LREE) reference to evaluate: 1) developmental defects (% DD) in HREE-exposed larvae or in the offspring of HREE-exposed sperm; 2) mitotic anomalies; 3) fertilization success; and 4) reactive oxygen species (ROS) formation, and nitric oxide (NO) and malondialdehyde (MDA) levels. Nominal HREE concentrations were confirmed by inductively coupled plasma mass spectrometry (ICP-MS). Results: HREEs induced concentration-related DD increases in P. lividus and A. lixula larvae, ranging from no significant DD increase at 10 −7 M HREEs up to ≅100% DD at 10 −5 M HREE. Larvae exposed to 10 −5 M Ce(III) resulted in less severe DD rates compared to HREEs. Decreased mitotic activity and increased aberration rates were found in HREE-exposed P. lividus embryos. Significant increases in ROS formation and NO levels were found both in HREE-exposed and in Ce(III) embryos, whereas only Ce(III), but not HREEs resulted in significant increase in MDA levels. Sperm exposure to HREEs (10 −5 –10 −4 M) resulted in a concentration-related decrease in fertilization success along with increase in offspring damage. These effects were significantly enhanced for Dy(III), Ho(III), Er(III) and Yb(III), compared to Lu(III) and to Ce(III). Conclusion: HREE-associated toxicity affected embryogenesis, fertilization, cytogenetic and redox endpoints showing different toxicities of tested HREEs. - Highlights: • Different toxicities were exerted by five tested HREEs on sea urchin early life stages. • Sea urchin embryos and sperm were sensitive to HREE levels ranging from 1 to 100 μM, according to

  15. Heavy rare earth elements affect early life stages in Paracentrotus lividus and Arbacia lixula sea urchins

    Oral, Rahime [Ege University, Faculty of Fisheries, TR-35100 Bornova, İzmir (Turkey); Pagano, Giovanni, E-mail: gbpagano@tin.it [“Federico II” University of Naples, Department of Chemical Sciences, I-80126 Naples (Italy); Stazione Zoologica Anton Dohrn, Villa Comunale, 80121 Naples (Italy); Siciliano, Antonietta; Gravina, Maria [“Federico II” University of Naples, Department of Biology, I-80126 Naples (Italy); Palumbo, Anna; Castellano, Immacolata; Migliaccio, Oriana [Stazione Zoologica Anton Dohrn, Villa Comunale, 80121 Naples (Italy); Thomas, Philippe J. [Environment and Climate Change Canada, Science & Technology Branch, National Wildlife Research Center – Carleton University, Ottawa, Ontario, Canada K1A 0H3 (Canada); Guida, Marco [“Federico II” University of Naples, Department of Biology, I-80126 Naples (Italy); Tommasi, Franca [University of Bari, Department of Biology, Bari (Italy); Trifuoggi, Marco [“Federico II” University of Naples, Department of Chemical Sciences, I-80126 Naples (Italy)

    2017-04-15

    Background: Heavy rare earth elements (HREEs) have been scarcely studied for their toxicity, in spite of their applications in several technologies. Thus HREEs require timely investigations for their adverse health effects. Methods: Paracentrotus lividus and Arbacia lixula embryos and sperm were exposed to trichloride salts of five HREEs (Dy, Ho, Er, Yb and Lu) and to Ce(III) as a light REE (LREE) reference to evaluate: 1) developmental defects (% DD) in HREE-exposed larvae or in the offspring of HREE-exposed sperm; 2) mitotic anomalies; 3) fertilization success; and 4) reactive oxygen species (ROS) formation, and nitric oxide (NO) and malondialdehyde (MDA) levels. Nominal HREE concentrations were confirmed by inductively coupled plasma mass spectrometry (ICP-MS). Results: HREEs induced concentration-related DD increases in P. lividus and A. lixula larvae, ranging from no significant DD increase at 10{sup −7} M HREEs up to ≅100% DD at 10{sup −5} M HREE. Larvae exposed to 10{sup −5} M Ce(III) resulted in less severe DD rates compared to HREEs. Decreased mitotic activity and increased aberration rates were found in HREE-exposed P. lividus embryos. Significant increases in ROS formation and NO levels were found both in HREE-exposed and in Ce(III) embryos, whereas only Ce(III), but not HREEs resulted in significant increase in MDA levels. Sperm exposure to HREEs (10{sup −5}–10{sup −4} M) resulted in a concentration-related decrease in fertilization success along with increase in offspring damage. These effects were significantly enhanced for Dy(III), Ho(III), Er(III) and Yb(III), compared to Lu(III) and to Ce(III). Conclusion: HREE-associated toxicity affected embryogenesis, fertilization, cytogenetic and redox endpoints showing different toxicities of tested HREEs. - Highlights: • Different toxicities were exerted by five tested HREEs on sea urchin early life stages. • Sea urchin embryos and sperm were sensitive to HREE levels ranging from 1 to 100

  16. Workshop summary. Biomedical and Space-Related Research with Heavy Ions at the BEVALAC

    Schimmerling, W.; Curtis, S. B.

    1989-01-01

    The authors provide an overview of papers presented at a workshop on Biomedical and Space-Related Research with Heavy Ions at the BEVALAC at Lawrence Berkeley Laboratory. Goals of the meeting were to determine the critical experiments using heavy ions as probes in radiation physics, radiation chemistry, macromolecular and cellular biology, evolution science, basic neurophysiology, and medical therapies; how beam lines and facilities at Lawrence Berkeley Laboratory can be improved for these experiments; and implications in priorities and funding for national policy. Workshop topics included physics and facilities, cellular and molecular biology, tissue radiobiology, and the future of heavy ion research.

  17. Commercial Aspect of Research Reactor Fuel Element Production

    Susanto, B.G; Suripto, A

    1998-01-01

    Several aspects affecting the commercialization of the Research Reactor Fuel Element Production Installation (RR FEPI) under a BUMN (state-owned company)have been studied. The break event point (BEP) value based on total production cost used is greatly depending upon the unit selling price of the fuel element. At a selling price of USD 43,500/fuel element, the results of analysis shows that the BEP will be reached at 51% of minimum available capacity. At a selling price of US$ 43.500/fuel element the total income (after tax) for 7 years ahead is US $ 4.620.191,- The net present value in this study has a positive value is equal to US $ 2.827.527,- the internal rate of return will be 18% which is higher than normal the bank interest rare (in US dollar) at this time. It is concluded therefore that the nuclear research reactor fuel element produced by state-owned company BUMN has a good prospect to be sold commercially

  18. Design and research of fuel element for pulsed reactor

    Tian Sheng

    1994-05-01

    The fuel element is the key component for pulsed reactor and its design is one of kernel techniques for pulsed reactor. Following the GA Company of US the NPIC (Nuclear Power Institute of China) has mastered this technique. Up to now, the first pulsed reactor in China (PRC-1) has been safely operated for about 3 years. The design and research of fuel element undertaken by NPIC is summarized. The verification and evaluation of this design has been carried out by using the results of measured parameters during operation and test of PRC-1 as well as comparing the design parameters published by others

  19. Research on weathering and biomarkers in heavy fuel oil

    Ma, Q.; Li, Z.; Yu, Z.

    2008-01-01

    The fate of oil spilled in the ocean depends on several physicochemical and biological factors such as evaporation, dissolution, microbial degradation and photo-oxidation. These weathering processes decrease the low molecules in spilled oils which reduces the harmful effects of spilled oil to the ocean and biota near the spill. In addition to changing the composition of the oil, some weathering processes are key to identifying the spilled oil. As such, the relationship between the weathering processes and the changes in oil composition must be well understood. This paper used gas chromatography and mass spectrometry (GC/MS) to analyze changes of chemical components in heavy fuel oil by weathering in static seawater. The major alkanes of heavy fuel oil include C8 to C33, while the major aromatics include benzene, naphthalene, phenanthrene and dibenzothiophene. After 24 weeks of weathering in seawater, the alkanes from n-C8 to n-C15 evaporated in order of increasing carbon number. The susceptibility of n-alkanes was correlated with carbon numbers. The aromatics evaporated in order of increasing carbon and ring number as weathering time increased. 8 refs., 3 tabs., 5 figs

  20. Recording of heavy ion tracks in silicates. Application to the determination of the abundance of ultra-heavy elements in old solar cosmic radiation

    Duraud, J.-P.

    1978-12-01

    The aim of this thesis is to determine the abundance A(Z) and energy spectrum of the elements of atomic number Z present in cosmic radiation, by means of fossil traces recorded in moon and meteorite minerals. The difficulties due amongst other things to natural annealing are examined in detail in part one, of this paper, the outcome being a thorough study of the processes responsible for the formation, chemical attack and annealing of heavy ion tracks. Part two describes an original approach used here and consisting of a combined analysis as a function of annealing for a given track, of the microscopic structure of the latent track and its attack rate. Part three uses the new rules established beforehand to propose a new method of studying the UH ion (Z>30) to VH ion (20 [fr

  1. Summary report on first research coordination meeting on heavy charged-particle interaction data for radiotherapy

    Palmans, H.; Noy, R.C.

    2008-04-01

    A summary is given of the First Research Coordination Meeting on Heavy Charged-Particle Interaction Data for Radiotherapy. A programme to compile and evaluate charged-particle nuclear data for therapeutic applications was proposed. Detailed coordinated research proposals were also agreed. Technical discussions and the resulting work plan of the Coordinated Research Project are summarized, along with actions and deadlines. (author)

  2. Probing for heavy element impurities in the shell of the Pacific oyster, Crassostrea gigas, with nuclear microscopy

    Markwitz, A.; Barry, B.; Gauldie, R.W.; Roberts, R.D.

    2003-01-01

    Nuclear microscopy was performed on shells of the Pacific oyster, Crassostrea gigas, to probe for heavy element impurities. For the studies 14 shells from the Auckland and the Marlborough Sounds region were chosen. In sections, the shells appear as opaque with white and grey zones, which are related to alternating layers of calcite and aragonite. Raster scans with 2.5 MeV protons over the sections (scan area 5 x 5 mm) were used in the experiment to measure trace elements in the ppm region using proton induced X-ray spectroscopy. Two dimensional maps and line scans revealed the presence of bromine in all shells investigated. Bromine was found to be related with the pattern of calcium. Hot spots of iron proved to be a common feature in the shells as well. In some shells, copper and zinc were also measured in hot spots of a few micrometers in diameter. Spatially resolved results on the micrometer level indicate the usefulness of nuclear microscopy for the detection of heavy elements in shells of the Pacific oyster

  3. Early History of Heavy Isotope Research at Berkeley

    Glenn T. Seaborg

    1976-06-01

    I have had the idea for some time that it would be interesting and worthwhile to put together an account of the early work on heavy isotopes at Berkeley. Of a special interest is the discovery of plutonium (atomic number 94) and the isotope U{sup 233}, and the demonstration of their fission with slow neutrons. This work served as a prelude to the subsequent Plutonium Project (Metallurgical Project) centered at the University of Chicago, in connection with which I have also had the idea of putting together a history of the work of my chemistry group. I have decided that it would be an interesting challenge to write this account on a day-to-day basis in a style that would be consistent with the entries having been written at the end of each day. The aim would be to make this history as accurate as possible by going back to the original records and using them with meticulous care.

  4. A Management Strategy for the Heavy Water Reflector Cooling System of HANARO Research Reactor

    Jung, H. S.; Park, Y. C.; Lim, S. P. (and others)

    2007-11-15

    Heavy water is used as the reflector and the moderator of the HANARO research reactor. After over 10 years operation since first criticality in 1995 there arose some operational issues related with the tritium. A task force team(TFT) has been operated for 1 year since September 2006 to study and deduce resolutions of the issues concerning the tritium and the degradation of heavy water in the HANARO reflector system. The TFT drew many recommendations on the hardware upgrade, tritium containing air control, heavy water quality management, waste management, and tritium measurement system upgrade.

  5. Mobilization of heavy metals from contaminated paddy soil by EDDS, EDTA, and elemental sulfur

    Wang, G.; Koopmans, G.F.; Song, J.; Temminghoff, E.J.M.; Luo, Y.; Zhao, Q.; Japenga, J.

    2007-01-01

    For enhanced phytoextraction, mobilization of heavy metals (HMs) from the soil solid phase to soil pore water is an important process. A pot incubation experiment mimicking field conditions was conducted to investigate the performance of three soil additives in mobilizing HMs from contaminated paddy

  6. The role fo the Pygmy resonance in the synthesis of heavy elements with radioactive beams

    Hussein, M.S.

    1990-12-01

    It is suggested that the inclusion of the virtual excitation of the soft giant dipole (pygmy) resonance in the calculation of the cross-section for very neutron-rich radioactive beam-induced fusion reactions may enhance the formation probability of the heavy compound nucleus produced at low excitation energy. (author)

  7. Analytical techniques and quality control in biomedical trace element research

    Heydorn, K.

    1994-01-01

    The small number of analytical results in trace element research calls for special methods of quality control. It is shown that when the analytical methods are in statistical control, only small numbers of duplicate or replicate results are needed to ascertain the absence of systematic errors....../kg. Measurement compatibility is obtained by control of traceability to certified reference materials, (C) 1994 Wiley-Liss, Inc....

  8. Effects of heavy elements in the sludge conveyed by the 2011 tsunami on human health and the recovery of the marine ecosystem

    Sera, K.; Goto, S.; Takahashi, C.; Saitoh, Y.; Yamauchi, K.

    2014-01-01

    The 2011 tsunami not only caused significant damage, but also drew a large amount of sludge from the bottom of the sea. This may have exerted negative effects on human health. In order to evaluate changes in elemental concentrations in the body before and after the tsunami, we collected long hairs from victims of the disaster. Furthermore, sludge and plant samples were collected from three prefectures. The sludge samples on land were found to be still contaminated with heavy elements. The concentrations of heavy elements in the soils and plants gathered from the same tidelands decreased after one year. In hair analyses, no clear changes have been observed in heavy element concentrations measured before and after the tsunami. However, the concentration of some essential elements, such as Cu, Ca and Mg, showed a decreasing tendency after the tsunami

  9. Effects of heavy elements in the sludge conveyed by the 2011 tsunami on human health and the recovery of the marine ecosystem

    Sera, K., E-mail: ksera@iwate-med.ac.jp [Cyclotron Research Center, Iwate Medical University, 348-58 Tomegamori, Takizawa 020-0173 (Japan); Goto, S.; Takahashi, C.; Saitoh, Y. [Takizawa Laboratory, Japan Radioisotope Association, 348-58 Tomegamori, Takizawa 020-0173 (Japan); Yamauchi, K. [Division of Pulmonary Medicine, Department of Internal Medicine, Iwate Medical University, 19-1 Uchimaru, Morioka 020-8505 (Japan)

    2014-01-01

    The 2011 tsunami not only caused significant damage, but also drew a large amount of sludge from the bottom of the sea. This may have exerted negative effects on human health. In order to evaluate changes in elemental concentrations in the body before and after the tsunami, we collected long hairs from victims of the disaster. Furthermore, sludge and plant samples were collected from three prefectures. The sludge samples on land were found to be still contaminated with heavy elements. The concentrations of heavy elements in the soils and plants gathered from the same tidelands decreased after one year. In hair analyses, no clear changes have been observed in heavy element concentrations measured before and after the tsunami. However, the concentration of some essential elements, such as Cu, Ca and Mg, showed a decreasing tendency after the tsunami.

  10. Application of insoluble tannin to recovery of uranium, TRU and heavy metals elements form radioactive liquid waste

    Hamaguchi, Kazuhiko; Shirato, Wataru; Nakamura, Yasuo; Matsumura, Tatsuro; Takeshita, Kenji; Nakano, Yoshio

    1999-01-01

    Mitsubishi Nuclear Fuel Co., Ltd. (MNF) has developed a new adsorbent, TANNIX (tread mark), for the recovery of uranium, TRU and heavy metal elements in the liquid waste, in which TANNIX derived from a natural tannin polymer. TANNIX has same advantages that handling is easier than that of standard IX-resin, and that the volume of secondary waste is reduced by burning the used TANNIX. We have replaced its radioactive liquid waste treatment system from the conventional co-precipitation process to adsorption process by using TANNIX. TANNIX was founded to be more effective for the recovery of Pu, TRU, and hexavalent chromium Cr-(VI) as well as Uranium. (author)

  11. Use of M and L transitions of heavy elements for the determination of a Si(Li) detector's efficiency

    Morales, J.R.; Romo, C.; Dinator, M.I.; Llona, F.; Tabacniks, M.

    1987-01-01

    The verification of the Si(Li) cryogenic detector's efficiency may be fastly carried out using the M radiations of the heavy elements, such as Pb and Au. Thin targets have been bombarded with protons of 2.0 and 6.6 MeV, thus resulting the transitions M and L. The number of emitted photons are possible to be inferred using tabulated cross sections from different authors. The comparison with the number of photons registered allows to determine the efficiency. (S.M.) [es

  12. Beyond darmstadtium -Status and perspectives of superheavy element research

    Ackermann, D.

    2005-01-01

    The search for superheavy elements has yielded exciting results for both the ''cold fusion'' approach with reactions employing Pb and Bi targets and the ''hot fusion'' reactions with 48 Ca beams on actinide targets. In recent years the accelerator laboratories in Berkeley, Dubna and Darmstadt have been joined by new players in the game in France with GANIL, Caen, and in Japan with RIKEN, Tokyo. The latter yielding very encouraging results for the reactions on Pb/Bi targets which confirmed the data obtained at GSI. Beyond the successful synthesis, interesting features of the structure of the very heavy nuclei like the hint for a possible K-isomer in 270 Ds or the population of states at a spin of up to 22ℎ in 254 No give a flavor of the exciting physics we can expect in the region at the very extreme upper right of the nuclear chart. To get a hand on it, a considerable increase in sensitivity is demanded from future experimental set-ups. High intensity stable beam accelerators, mass measurement in ion traps and mass spectrometers, as well as the possible employment of unstable neutron-rich projectile species, initially certainly only for systematic studies of reaction mechanism and nuclear structure features for lighter exotic neutron-rich isotopes, are some of the technological challenges which have been taken on. (orig.)

  13. Contributing to research: the basic elements of a scientific manuscript

    Kurmis, A.P.

    2003-01-01

    The changing focus within medical and allied health disciplines towards evidence-based practice has resulted in an increasing acceptance of research and professional researchers. Despite the shift towards tertiary degree-based training for medical imaging and allied specialty streams, with many teaching institutions now incorporating compulsory research components into their final year curriculum, the level of active involvement in research among graduates remains low. In addition to this, many of those who completed their training before the introduction of university degree courses have had little or no exposure to hands-on research. While not overtly difficult, the process of 'writing up' the findings of a research endeavour for presentation to peers can often seem a somewhat daunting task, especially for novice researchers. The structure of a scientific manuscript however follows a relatively basic and universally accepted pattern, adherence to which can greatly simplify the writing process. To contribute to a wider understanding of research, the purpose of this paper is to provide an overview of the basic elements of a scientific research paper for journal publication. The outline provided, while not intended to be a recipe for manuscript construction, will provide a fundamental framework to assist student, junior or inexperienced researchers in their writings

  14. Discourse on Narrative Research: The Construction Zone--Literary Elements in Narrative Research

    Coulter, Cathy A.; Smith, Mary Lee

    2009-01-01

    Narrative research has become part of the landscape of education inquiry, yet its theory and practice are still debated and evolving. This article addresses the construction of narratives using literary elements common to nonfiction and fiction writings. The authors discuss these elements and use four narratives to illustrate them. They address…

  15. Nuclear research with heavy ions. Annual progress report, January 1, 1977--December 31, 1977

    Kaplan, M.

    1977-10-01

    The experimental research program consists of several interrelated parts: (1) Reactions of Very Heavy Ions with Complex Nuclei; (2) Studies of Compound Nucleus Reactions Induced by Heavy Ions; and (3) Recoil Studies of Heavy Ion Reactions. Using solid-state detector telescopes and gas-ionization detector telescopes we have studied the emission of 1 H, 2 H, 3 H, 4 He and heavy fragments from the reactions of 720 MeV 86 Kr with 197 Au. Coincidence measurements between light charged particles and a heavy fragment indicate that most of the observed 4 He particles are evaporated by equilibrated Kr*-like and Au*-like excited products from deep inelastic reactions, but a significant number of preequilibrium 4 He particles seem to be emitted in directions normal to the separating fragments. Studies of angular correlations between two heavy fragments provide strong evidence for sequential fission of the Au*-like reaction fragments, and the probability of this process has been estimated as a function of Q, the energy damping in the primary collision. Parallel studies of charged particle emission, fission, and evaporation residues in compound nucleus reactions map out the de-excitation characteristics of highly excited heavy nuclei as functions of E* and J. Results are presented for the compound nucleus 194 Hg formed at matched excitation energies via different entrance channels

  16. Heavy-ion fusion driver research at Berkeley and Livermore

    Seidl, P.; Bangerter, R.; Celata, C.M.

    1996-08-01

    The Department of Energy is restructuring the U.S. fusion program to place a greater emphasis on science. As a result, we will not build the ILSE or Elise heavy ion fusion (HIF) facilities described in 1992 and 1994 conferences. Instead we are performing smaller experiments to address important scientific questions. Accelerator technology for HIF is similar to that for other applications such as high energy physics and nuclear physics. The beam physics, however, differs from the physics encountered in most accelerators, where the pressure arising from the beam temperature (emittance) is the dominant factor determining beam size and focusing system design. In HIF, space charge is the dominant feature, leading us into a parameter regime where.the beam plasma frequency becomes comparable to the betatron frequency. Our experiments address the physics of non-neutral plasmas in this novel regime. Because the beam plasma frequency is low, Particle-in-cell (PIC) simulations provide a good description of most of our experiments. Accelerators for HIF consist of several subsystems: ion sources, injectors, matching sections, combiners, acceleration sections with electric and magnetic focusing, beam compression and bending sections, and a system to focus the beams onto the target. We are currently assembling or performing experiments to address the physics of all these subsystems. This paper will discuss experiments in injection, combining, and bending

  17. Finite element modeling simulation-assisted design of integrated microfluidic chips for heavy metal ion stripping analysis

    Hong, Ying; Zou, Jianhua; Ge, Gang; Xiao, Wanyue; Shao, Jinjun; Dong, Xiaochen; Gao, Ling

    2017-01-01

    In this article, a transparent integrated microfluidic device composed of a 3D-printed thin-layer flow cell (3D-PTLFC) and an S-shaped screen-printed electrode (SPE) has been designed and fabricated for heavy metal ion stripping analysis. A finite element modeling (FEM) simulation is employed to optimize the shape of the electrode, the direction of the inlet pipeline, the thin-layer channel height and the sample flow rate to enhance the electron-enrichment efficiency for stripping analysis. The results demonstrate that the S-shaped SPE configuration matches the channel in 3D-PTLFC perfectly for the anodic stripping behavior of the heavy metal ions. Under optimized conditions, a wide linear range of 1–80 µ g l −1 is achieved for Pb 2+ detection with a limit of 0.3 µ g l −1 for the microfluidic device. Thus, the obtained integrated microfluidic device proves to be a promising approach for heavy metal ions stripping analysis with low cost and high performance. (paper)

  18. Accelerator mass spectrometry of heavy elements: /sup 36/Cl to /sup 205/Pb

    Henning, W

    1987-08-25

    Measurements are discussed in which the technique of accelerator mass spectrometry was applied to problems involving heavy radioisotopes. These measurements, which depend on the ion energies that can be reached with the new heavy-ion accelerator facilities, were performed at the Argonne tandem linac accelerator system (ATLAS) and at the UNILAC accelerator at GSI. The topics include a discussion of measurements of long nuclear lifetimes, of radioisotope detection of interest to solar neutrino experiments, and of a determination of the /sup 41/Ca concentration in natural samples of terrestrial origin by making use of isotopic pre-enrichment in an isotope separator. A long-known method of isobar separation, employing a gas-filled magnetic field region, has been revived for some of these measurements and its characteristics and advantages are briefly reviewed.

  19. Physical linkage of a human immunoglobulin heavy chain variable region gene segment to diversity and joining region elements

    Schroeder, H.W. Jr.; Walter, M.A.; Hofker, M.H.; Ebens, A.; Van Dijk, K.W.; Liao, L.C.; Cox, D.W.; Milner, E.C.B.; Perlmutter, R.M.

    1988-01-01

    Antibody genes are assembled from a series of germ-line gene segments that are juxtaposed during the maturation of B lymphocytes. Although diversification of the adult antibody repertoire results in large part from the combinatorial joining of these gene segments, a restricted set of antibody heavy chain variable (V H ), diversity (D H ), and joining (J H ) region gene segments appears preferentially in the human fetal repertoire. The authors report here that one of these early-expressed V H elements (termed V H 6) is the most 3' V H gene segment, positioned 77 kilobases on the 5' side of the J H locus and immediately adjacent to a set of previously described D H sequences. In addition to providing a physical map linking human V H , D H , and J H elements, these results support the view that the programmed development of the antibody V H repertoire is determined in part by the chromosomal position of these gene segments

  20. Heavy metal, trace element and petroleum hydrocarbon pollution in the Arabian Gulf: Review

    Afnan Mahmood Freije

    2015-01-01

    The Arabian Gulf environmental status was assessed based on studies conducted in Bahrain, Kuwait, Oman, Saudi Arabia, Qatar, and United Arab Emirates (UAE) during 1983–2011. This review examines all sorts of pollutions in the Arabian Gulf area over the last three decades. Approximately 50 published studies were reviewed in order to determine the pollution status in the Arabian Gulf regarding heavy metals and organic substances. Three types of environmental pollutions including marine and coas...

  1. Heavy ion fusion accelerator research in the US

    Bangerter, R.O.; Godlove, T.F.; Herrmannsfeldt, W.B.; Keefe, D.

    1984-09-01

    Three new development have taken place in the HIFAR program. First, a decision has been made to concentrate the experimental program on the development of multiple-beam induction linacs. Second, new beam transport experiments over a large number of quadrupole elements show that stable beam propagation occurs for significantly higher beam currents than had been believed possible a few years ago. Third, design calculations now show that a test accelerator of modest size and cost can come within a factor of three of testing almost all of the physics and technical issues appropriate to a power-plant driver

  2. Labile rhizosphere soil solution fraction for prediction of bioavailability of heavy metals and rare earth elements to plants.

    Shan, Xiao-Quan; Wang, Zhongwen; Wang, Weisheng; Zhang, Shuzhen; Wen, Bei

    2003-02-01

    A labile rhizosphere soil solution fraction has been recommended to predict the bioavailability of heavy metals and rare earth elements to plants. This method used moist rhizosphere soil in combination with a mixture of 0.01 mol L(-1) of low-molecular-weight organic acids (LMWOAs) as extractant. The extracted soil solutions were fractionated into two colloidal fractions of soil solution fraction, F(lrss). For the soil solutions extracted with a mixture of LMWOAs the concentrations of heavy metals and rare earth elements in F(2) and F(3) were quite similar. However, the mean concentrations of Cr, Ni, Zn, Cu, Pb, Cd, La, Ce, Pr, and Nd in F(lrss) accounted for 79.9%, 91.3%, 90.8%, 60.1%, 77.5%, 75.3%, 81.2%, 77.2%, 80.3%, and 79.5%, respectively, of their concentrations in F(2). In contrast, there were no differences in the extractable metal concentrations between the three fractions while the first step of the method recommended by the European Community of Reference (BCR), where 0.1 mol L(-1) acetic acid was used as an extractant. The single correlation analysis was made between metal concentrations in the different fractions of soil solutions and their concentrations in wheat. If the first step of BCR method was used there was no good correlation between heavy metals in soil pools and that in wheat shoots and roots. When LMWAOs were used a good correlation was obtained between the concentrations of heavy metals in soil pools and that in wheat roots, which followed a general order of r(1 kD, LMWOAs) >r(0.2 microm, LMWOAs) approximately r(0.45 microm, LMWOAs). In the case of rare earth elements the good correlation was obtained for both the wheat roots and shoots. Generally, the correlation coefficients obtained by LMWAOs were better than that obtained by the first step of BCR method. Therefore, LMWAOs and F(lrss) were strongly recommended to predict the bioavailability of metals in soil pools to plants.

  3. The application of f-elements in ecological research

    Knaus, R.M.

    1991-01-01

    The utilization of f-elements has a relatively minor status as a research tool in the biological sciences, especially ecology, because they play neither positive nor deleterious roles in plant and animal nutrition. Additionally, detection and quantification via instrumental neutron activation analysis (INAA) of environmental samples is not yet routine. At Louisiana State University, La, Sm, and Dy have been used successfully as activable stable tracers in a wide range of ecological studies including the quantification using Sm and Dy of short-term sedimentary and erosional processes in wetlands; and behavior studies using Sm on agricultural lands where radioisotopes are precluded; the sorption of Dy and La by roots of stream-side trees; and the quantification of exogenous Dy and Sm from animal decay products in streams. With advances in sample automation and standardization in INAA detection methods, the quantification of f-element tracers in complex biological matrices is within reach of ecological scientists

  4. Research sources of ionizing radiation based on transplutonium elements

    Radchenko, V. M.; Ryabinin, M. A.

    2010-03-01

    Scientific and technical demand stimulates an extension of the practical implementation field of TPE, requirements to their ecological safety calling for the development of such materials which could be most resistant to the environment and most suitable for the production of a wide range of sources different in their application and design. Such materials can involve pure metals of transplutonium elements and their alloys with metals of platinum group as well as their chemically stable compounds (such as silicides, carbides etc.) At SSC RIAR production processes of sources of different type and application have been implemented. Examples of the most recent developments of the sources are presented below. Presented is the analysis of the current state of issues related to designing, production and application of radionuclide research sources based on transplutonium elements. Examples of the development of the most up-to-date sources of alpha-, gamma- and neutron radiation and also fission ones are considered.

  5. Research of Two Different Impulsive Faults of Rolling Element Bearing

    Jiang Zhinong; Xing Chenghong; Feng Kun; Gao Jinji

    2012-01-01

    Fans and pumps are key machines in process industries such as petrochemical and petroleum industries. Their faults can be catastrophic and result in costly downtime. Bearing fault is almost the most common fault of fans and pumps as rolling element bearings are widely used in these machines. Hence, condition monitoring and diagnosis of bearings are important. Two different impulsive faults of bearings have been observed and studied in previous research. The first fault presents very clear impulsive symptom in envelope spectrum, but the bearing can work for a long time. The other fault shows relatively indistinct symptom, but the bearing will break down in a short time. To overcome the problems of inaccurate diagnosis, a combinational approach based on an impulsive energy indicator and traditional enveloping analysis is proposed in this paper. This approach discriminate these two faults well and can support the maintenance decision for the machines with rolling element bearings.

  6. Geological research on rare earth elements, results and outlook

    Fortin, H

    1999-01-01

    This is a report of the geological investigation of rare earth elements carried out by CCHEN and ENAMI (Empresa Nacional de Mineria) over 70,000 square kilometers in Chile's northern coastal mountain range. Twenty areas were identified with sphena, davidite, ilmenite, pyroxene, anatase and magnetite minerals containing 0.3 kg/t to 6.0 kg/t of rare earth elements. Additional research on Cerro Carmen Prospect, located near Diego de Almagro, define it as a metasomatic deposit, hosted in metamorphic contact rocks, between andesites (Pliensbachian to early Jurassic) and intrusive monzonitic rocks. This information increases knowledge about the metallogenesis of Chile's copper - iron - rare earth - uranium deposits and the application of this geological model of ore deposits as defined in Australia's Olympic Dam

  7. Theoretical Predictions of Cross-Sections of the Super-Heavy Elements

    Bouriquet, B.; Kosenko, G.; Abe, Y.

    The evaluation of the residue cross-sections of reactionssynthesising superheavy elements has been achieved by the combination of the two-step model for fusion and the evaporation code (KEWPIE) for survival probability. The theoretical scheme of those calculations is presented, and some encouraging results are given, together with some difficulties. With this approach, the measured excitation functions of the 1n reactions producing elements with Z=108, 110, 111 and 112 are well reproduced. Thus, the model has been used to predict the cross-sections of the reactions leading to the formation of the elements with Z=113 and Z=114.

  8. Theoretical predictions of cross-sections of the super-heavy elements

    Bouriquet, B.; Abe, Y.; Kosenko, G.

    2004-01-01

    The evaluation of the residue cross-sections of reactions synthesising superheavy elements has been achieved by the combination of the two-step model for fusion and the evaporation code (KEWPIE) for survival probability. The theoretical scheme of those calculations is presented, and some encouraging results are given, together with some difficulties. With this approach, the measured excitation functions of the 1n reactions producing elements with Z = 108, 110, 111 and 112 are well reproduced. Thus, the model has been used to predict the cross-sections of the reactions leading to the formation of the elements with Z = 113 and Z = 114. (author)

  9. U.S. Department of Energy Office of Science Heavy Elements Program. Final Report

    Clark. S. B.; Ewing, R.

    2005-01-01

    In our first funding cycle, much time was spent developing protocols for characterizing and working with samples containing transuranium isotopes and obtaining preliminary experimental data on non-f-element systems

  10. Rotating target wheel system for super-heavy element production at ATLAS

    Greene, J P; Falout, J; Janssens, R V F

    2004-01-01

    A new scattering chamber housing a large diameter rotating target wheel has been designed and constructed in front of the Fragment Mass Analyzer (FMA) for the production of very heavy nuclei (Z greater than 100) using beams from the Argonne Tandem Linear Accelerator System (ATLAS). In addition to the target and drive system, the chamber is extensively instrumented in order to monitor target performance and deterioration. Capabilities also exist to install rotating entrance and exit windows for gas cooling of the target within the scattering chamber. The design and initial tests are described.

  11. Production of heavy element and search for new isotopes at JAERI-RMS

    Ikuta, Tomohiko [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-07-01

    The new neutron deficient isotope {sup 209}Th and {sup 212}Pa have been produced in heavy ion induced fusion evaporation reactions. The evaporation residues were separated in-flight by the JAERI recoil mass separator (JAERI-RMS). The {alpha}-decay energy of {sup 209}Th and {sup 212}Pa are 8.080(50) MeV and 8.270(30) MeV, respectively. The corresponding half-lives are 3.8{sub -1.5}{sup +6.9} ms and 5.1{sub -1.9}{sup +6.1} ms. (author)

  12. The case for exotic beams at the Holifield Heavy Ion Research Facility

    Garrett, J.D.

    1991-01-01

    The case is presented for modifying the Holifield Heavy Ion Research Facility at Oak Ridge National Laboratory to provide beams of proton-rich exotic isotopes, that do not occur terrestrially. A program of nuclear structure studies for light- and medium-mass, nearly self-conjugate nuclei and for heavy, proton-rich, quasibound nuclei is outlined, as are studies of hydrogen-burning reactions that occur in nucleosynthetic processes. Such a scientific program will provide a unique future for nuclear physics research at ORNL consistent with the long standing tradition of this laboratory

  13. The superTIGER instrument: Measurement of elemental abundances of ultra-heavy galactic cosmic rays

    Binns, W. R.; Bose, R. G.; Braun, D. L.; Dowkontt, P. F.; Israel, M. H.; Moore, P.; Murphy, R. P.; Olevitch, M. A.; Rauch, B. F. [Washington University, St. Louis, MO 63130 (United States); Brandt, T. J.; Daniels, W. M.; Fitzsimmons, S. P.; Hahne, D. J.; Hams, T.; Link, J. T.; Mitchell, J. W.; Sakai, K. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Klemic, J.; Labrador, A. W.; Mewaldt, R. A., E-mail: wrb@wustl.edu [California Institute of Technology, Pasadena, CA 91125 (United States); and others

    2014-06-10

    The SuperTIGER (Super Trans-Iron Galactic Element Recorder) instrument was developed to measure the abundances of galactic cosmic-ray elements from {sub 10}Ne to {sub 40}Zr with individual element resolution and the high statistics needed to test models of cosmic-ray origins. SuperTIGER also makes exploratory measurements of the abundances of elements with 40 < Z ≤ 60 and measures the energy spectra of the more abundant elements for Z ≤ 30 from about 0.8 to 10 GeV/nucleon. This instrument is an enlarged and higher resolution version of the earlier TIGER instrument. It was designed to provide the largest geometric acceptance possible and to reach as high an altitude as possible, flying on a standard long-duration 1.11 million m{sup 3} balloon. SuperTIGER was launched from Williams Field, McMurdo Station, Antarctica, on 2012 December 8, and made about 2.7 revolutions around the South Pole in 55 days of flight, returning data on over 50 × 10{sup 6} cosmic-ray nuclei with Z ≥ 10, including ∼1300 with Z > 29 and ∼60 with Z > 49. Here, we describe the instrument, the methods of charge identification employed, the SuperTIGER balloon flight, and the instrument performance.

  14. Glenn Seaborg's Contributions to Heavy Element Science and the Periodic Table

    Hobart, David E.

    2012-01-01

    In celebrating the centennial anniversary of the birth of Glenn T. Seaborg it is fitting that we recount and pay tribute to his legacy. Many know of the scientific accomplishments of this man who became a legend and anyone who has attended his lectures can attest to how informative, educational, and entertaining he was. He had a beguiling and whimsical sense of humor and used this to drive home his points and share his passion and quest for discovery. The periodic table is a fundamental cornerstone of science and remains a central unifying principal. Seaborg was the architect of the actinide series of elements and their proper placement in the periodic table and co-discoverer of ten transuranium elements - one of which bears his name, element 106, seaborgium. The work and achievements of this Nobel laureate have touched the lives of many and his legacy will continue for generations to come.

  15. Glann Seaborg's Contributions to Heavy Element Science and the Periodic Table

    Hobart, David E. [Los Alamos National Laboratory

    2012-08-17

    In celebrating the centennial anniversary of the birth of Glenn T. Seaborg it is fitting that we recount and pay tribute to his legacy. Many know of the scientific accomplishments of this man who became a legend and anyone who has attended his lectures can attest to how informative, educational, and entertaining he was. He had a beguiling and whimsical sense of humor and used this to drive home his points and share his passion and quest for discovery. The periodic table is a fundamental cornerstone of science and remains a central unifying principal. Seaborg was the architect of the actinide series of elements and their proper placement in the periodic table and co-discoverer of ten transuranium elements - one of which bears his name, element 106, seaborgium. The work and achievements of this Nobel laureate have touched the lives of many and his legacy will continue for generations to come.

  16. Uptake of traffic-related heavy metals and platinum group elements (PGE) by plants

    Schaefer, J.; Hannker, D.; Eckhardt, J.D.; Stueben, D. [Institute of Petrography and Geochemistry, University of Karlsruhe, Karlsruhe (Germany)

    1998-04-23

    The distribution of the platinum group elements (PGE) caused by traffic emissions from autoexhaust catalysts has been determined in soils and different types of plants. The plants (spinach, cress, phacelia, stinging nettle) were cultivated on different soils collected from areas adjacent to a German highway and on uncontaminated sandy and clayey soils. The main result of the experiments was a measurable transfer of PGE from contaminated soil to plants. Following the definition of Sauerbeck (Beurteilung von Schwermetallkontaminationen im Boden. Frankfurt/Main: Dechema-Fachgespraeche, 1989:281-316), Pt, Rh and Pd transfer coefficients are within the range of immobile to moderately mobile elements, such as Cu. The transfer coefficient decreases from Pd>Pt{>=}Rh. Palladium therefore is the most biologically available of this element group

  17. Fuel element gamma scanning at the Oak Ridge Research Reactor

    Hobbs, R.W.

    1987-01-01

    In January 1986, a demonstration program was begun at the Oak Ridge Research Reactor (ORR) to convert operations from high-enrichment uranium fuel to the newly developed U 3 Si 2 low-enrichment fuel. A primary program objective is to validate neutronics calculations conducted by the Reduced Enrichment in Research and Test Reactors Program at Argonne National Laboratory. Accordingly, a new method for determining core-power distribution has been developed. The method is based on gamma-ray spectroscopy measurements to determine the relative levels of 140 La in the fuel elements after each operating cycle. The measurement and data analyses are described and a comparison of measured and diffusion theory calculated values of the core-power distribution is presented in this paper

  18. A comprehensive analysis of the content of heavy rare-earth elements and platinum in snow samples to assess the ecological hazard of air pollution in urban areas

    Vinokurov, S. F.; Tarasova, N. P.; Trunova, A. N.; Sychkova, V. A.

    2017-07-01

    Snow samples from the territory of the Setun River Valley Wildlife Sanctuary are analyzed for the content of rare-earth elements, heavy metals, and other hazardous elements by the inductively coupled plasma mass-spectrometry method. The changes in the concentrations of rare-earth elements, Pt, Pd, and indicator ratios of elements in the solid fractions of snow are revealed. A trend toward a decrease in the content of several elements northeastward of the Moscow Ring Road (MRR) is established. The level of seasonal atmospheric contamination of the area under study is assessed, and a possible source is identified.

  19. Excessive Yield of Second Charged ions of Heavy Elements in Laser Plasma Expansion Process

    Kouznetsov, G.B.; Sysoev, A.A.

    2002-01-01

    LAMAS-IOM TOF-MS that was recently designed for inorganic quantitative analysis is also well suitable for investigation of laser irradiation interaction with solids. This feature allows one to analyze plasma on early stage and gives an excellent possibility to complete existent physical model. This work is dedicated to investigation of yield doubly charged ions for different elements

  20. Gradient of heavy elements in the sea bed of the Gulf of Tehuantepec

    Ramirez T, J.J.; Lopez M, J.; Aspiazu F, J.A.; Villasenor S, P.; Ordonez, E.; Gutierrez, A.; Ruiz F, A.C.

    2006-01-01

    Using the PIXE technique the concentrations of some elements was analyzed weighed in a sedimentary nucleus gathered in the Gulf of Tehuantepec. The certain profiles of concentrations are presented and the utility of the PIXE technique is demonstrated for the study of environmental processes. (Author)

  1. The determination of light elements in heavy matrix using proton induced X-ray emission

    Levenets, V.V.; Omel'nik, A.P.; Shchur, A.A.; Chernov, A.E.; Usikov, N.P.; Zats, A.V.

    2007-01-01

    In this report the possibility of determination of light impurities in heavy matrixes is studied using proton induced X-Ray emission. The wide-band X-ray emission filter made from pyrolytic graphite was used in spectrometric scheme of experiment. The results of studying of filter features in energy range of X-ray emission from 4 to 12 keV were presented. The possibilities were examined of application of pyrolytic graphite filter to modify the X-rays spectrum for determination of iron, using characteristic emission of K-series, and hafnium, using L-series, in substances on base of zirconium (glasses, alloys etc.). It was shown, that the using of similar filter allows to reach the significant improving of metrological characteristics of analysis of mentioned impurities: the limits of detection of iron and hafnium were lowered single-order of magnitude. (authors)

  2. Distributing Characteristics of Heavy Metal Elements in A Tributary of Zhedong River in Laowangzhai Gold Deposit, Yunnan (China): An Implication to Environmentology from Sediments

    Yang, Shuran; Danĕk, Tomáš; Yang, Xiaofeng; Cheng, Xianfeng

    2016-10-01

    Five heavy metal contents from five sediments and seven sediment profiles in an upstream reach of Zhedong river in Laowangzhai gold deposit were investigated in this research, along with analysis of the horizontal distribution, the surface distribution, the vertical distribution and the interlayer distribution of five heavy metal contents: arsenic (As), mercury (Hg), copper (Cu), lead (Pb) and zinc (Zn). The potential ecological risk of five heavy metals was evaluated to help understanding pollution control of Laowangzhai deposit.

  3. Assessment of the essential element and heavy metal content of edible fish muscle

    Carvalho, M.L.; Santiago, S. [Centro de Fisica Atomica, Faculdade de Ciencias da Universidade de Lisboa, Departamento de Fisica, Lisboa (Portugal); Nunes, M.L. [Instituto de Investigacao das Pescas e do Mar, Lisboa (Portugal)

    2005-05-01

    The aim of this work was to determine the concentrations of some essential and toxic elements in the muscle of ten species of commercial fish consumed in Portugal. We combined two different techniques for determination of the elements - energy-dispersive X-ray fluorescence (EDXRF) was used to quantify K, Ca, Fe, Zn, Se, Rb, and Sr and flame atomic-absorption spectrometry for analysis of Cr, Ni, Cu, Cd, Hg, and Pb. The latter technique was used because of its higher sensitivity, because these elements were not detected by EDXRF. The results obtained show a similar pattern for the trace elements. K and Ca are present at the highest concentrations in all the samples studied, from 0.6-1.3% and from 0.04-0.08%, respectively, followed by Zn, Fe, Sr, Se, and Rb. Sr is present at higher concentrations than Rb in all the species studied except meagre. Concentrations of the elements in octopus do not follow this pattern - Fe is present at a higher concentration than Zn. Low concentrations of Cr (0.66-1.5 {mu}g g{sup -1}), Ni (0.11-0.24 {mu}g g{sup -1}), Cd (0.01-0.08 {mu}g g{sup -1}), Hg (0.49-2.74 {mu}g g{sup -1}), and Pb (0.02-0.06 {mu}g g{sup -1}) were observed in all the samples analysed. The concentration of Hg was highest in Helicolenus dactylopterus - 5.4 {mu}g g{sup -1} in one sample. (orig.)

  4. Effect of silver nanoparticles on concentration of silver heavy element and growth indexes in cucumber (Cucumis sativus L. negeen)

    Shams, Gholamabbas; Ranjbar, Morteza; Amiri, Aliasghar

    2013-01-01

    The tremendous progress on nanoparticle research area has been made significant effects on the economy, society, and the environment. Silver nanoparticle is one of the most important particles in these categories. Silver nanoparticles can be converted to the heavy silver metal in water by oxidation. Moreover, in the high amounts of silver concentration, they will be accumulated in different parts of the plant. However, by changing the morphology of the plant, the production will be harmful for human consumptions. In this study, nano-powders with average 50 nm silver particles are mixed with deionized distilled water in a completely randomized design. Seven treatments with various concentrations of suspension silver nanoparticles were prepared and repeated in four different parts of the plant in a regular program of spraying. Samples were analyzed to study the growth indexes and concentration of silver in different parts of the plant. It was observed that with increasing concentration of silver nanoparticles on cucumber, the growth indexes (except pH fruit), and the concentration of silver heavy metal are increased significantly. The incremental concentration had the linear relationship with correlation coefficient 0.95 and an average of 0.617 PPM by increasing of each unit in one thousand concentration of nanosilver. Although, by increasing concentration of silver nanoparticles as spraying form, the plant morphological characteristics were improved, the concentration of silver heavy metal in various plant organs was increased. These results open a new pathway to consider the effect of nanoparticles on plant’s productions for human consumptions.

  5. Analysis of heavy alloying elements segregation in gravity cast experimental Mg-Al-Zn-RE alloy

    A. Żydek

    2010-01-01

    Full Text Available Microstructure of experimental AZ91 alloy with an addition of rare earth elements (RE at a level of 4 wt.% was examined by means of light microscopy. The investigated AZ91 + 4 wt.% RE alloy was fabricated by adding cerium rich mish metal to molten commercial AZ91 alloy. In the microstructure of the resulting alloy, besides α solid solution, α + γ eutectic and discontinuous precipitates of γ phase, also the Al11RE3 phase with needle-like morphology and the polygonal Al10RE2Mn7 phase were revealed. No segregation of rare earth elements was found in the investigated gravity cast alloy, which was confirmed by statistical analysis of cerium concentrations in selected parts of the cast. Similar results were obtained for manganese. Ce and Mn concentrations were determined by a spectrophotometric method.

  6. Comparison study between traditional and finite element methods for slopes under heavy rainfall

    M. Rabie

    2014-08-01

    Moreover, slope stability concerning rainfall and infiltration is analyzed. Specially, two kinds of infiltrations (saturated and unsaturated are considered. Many slopes become saturated during periods of intense rainfall or snowmelt, with the water table rising to the ground surface, and water flowing essentially parallel to the direction of the “slope” and “Influence” of the change in shear strength, density, pore-water pressure and seepage force in soil slices on the slope stability is explained. Finally, it is found that classical limit equilibrium methods are highly conservative compared to the finite element approach. For assessment the factor of safety for slope using the later technique, no assumption needs to be made in advance about the shape or location of the failure surface, slice side forces and their directions. This document outlines the capabilities of the finite element method in the analysis of slope stability problems.

  7. Determination of pollutant elements and heavy metals in petroleum sludge and scale at Heglig field Sudan

    Amir, N. T.

    2012-02-01

    The release of pollutant metals from petroleum industry in to ecosystems represents a serious hazard for the biosphere, because of their toxicity. The objective of this study was to determine the levels of some elements in petroleum sludge and scales collected from petroleum production area in Heglig oil field located in South Kordofan State. The concentration of Ca, Fe, V, Mn,Ni, Cu, Zn, Cs, Sr, Zr, Y and Pb in sludge and scale samples have been determined using energy dispersive x-ray fluorescence (EDXRF) equipped with a point source of 1 09C d. The concentration of Ca and Fe in scale samples were found to fall in range of 15,49-23.28% and 0.98-5.13%, respectively. The a verge elemental concentrations of Ti, Mn, Ni, Cu, Zn, Sr,Y, and Pb in scale samples were 2917.8, 567.74, 23.21, 23.05, 101.67, 31.38, 177.06 and 24.12 (mg/kg), respectively. The concentrations of Ca and Fe in sludge samples ranged from 1.98-8.82% and 0.71-5.19%, respectively and the a verge elemental concentrations of Cs, V, Mn,Cu, Zn, Pb, Sr, Y and Zr were 7.44, 92,59, 557.36, 7.67, 162.72,28.67, 65.02, 45.64 and 52.15 (mg/kg), respectively. Correlation analysis revealed lock of any significant correlation between elemental concentrations in sludge and scales. (Author)

  8. Heavy Metals and Trace Elements Atmospheric Deposition Studies in Tula Region Using Moss Biomonitors Technique

    Ermakova, E V; Steinnes, E

    2002-01-01

    For the first time the moss biomonitors technique was used in air pollution studies in Tula Region (Central Russia), applying NAA, AAS. Moss samples were collected at 83 sites in accordance with the sampling strategy adopted in European projects on biomonitoring atmospheric deposition. A wide set of trace elements in mosses was determined. The method of epithermal neutron activation at IBR-2 reactor of FLNP JINR has made it possible to identify 33 elements (Na, Mg, Al, Cl, K, Ca, Sc, V, Cr, Mn, Fe, Co, Ni, Zn, As, Br, Rb, Sr, Mo, Sb, I, Cs, Ba, La, Ce, Sm, Tb, Yb, Hf, Ta, W, Th, U) in the large-scale concentration range - from 10000 ppm for K to 0,001 ppm for Tb and Ta. Cu, Cd and Pb were determined by the flame AAS in the Norwegian Institute of Science and Technology. Using the graphical technique and principal component analysis allowed to separate plant, crustal and general pollution components in the moss. The obtained data will be used for constructing coloured maps of the distribution of elements over t...

  9. Research and Development of Heavy Wall DNV485FDU Pipeline Plate for 3500M Deep Water Pipe Applications at Shougang

    Ding, Wenhua; Li, Shaopo; Li, Jiading; Li, Qun; Chen, Tieqiang; Zhang, Hai

    In recent years, there has been development of several significant pipeline projects for the transmission of oil and gas from deep water environments. The production of gas transmission pipelines for application demands heavy wall, high strength, good lower temperature toughness and good weldability. To overcome the difficulty of producing consistent mechanical property in heavy wall pipe Shougang Steel Research in cooperation with the Shougang Steel Qinhuangdao China (Shouqin) 4.3m heavy wide plate mill research was conducted.

  10. US Heavy Ion Beam Research for Energy Density Physics Applications and Fusion

    Davidson, R.C.; Logan, B.G.; Barnard, J.J.; Bieniosek, F.M.; Briggs, R.J.; Callahan D.A.; Kireeff Covo, M.; Celata, C.M.; Cohen, R.H.; Coleman, J.E.; Debonnel, C.S.; Grote, D.P.; Efthimiom, P.C.; Eylon, S.; Friedman, A.; Gilson, E.P.; Grisham, L.R.; Henestroza, E.; Kaganovich, I.D.; Kwan, J.W.; Lee, E.P.; Lee, W.W.; Leitner, M.; Lund, S.M.; Meier, W.R.; Molvik, A.W.; Olson, C.L.; Penn, G.E.; Qin, H.; Roy, P.K.; Rose, D.V.; Sefkow, A.; Seidl, P.A.; Sharp, W.M.; Startsev, E.A.; Tabak, M.; Thoma, C.; Vay, J-L; Wadron, W.L.; Wurtele, J.S.; Welch, D.R.; Westenskow, G.A.; Yu, S.S.

    2005-01-01

    Key scientific results from recent experiments, modeling tools, and heavy ion accelerator research are summarized that explore ways to investigate the properties of high energy density matter in heavy-ion-driven targets, in particular, strongly-coupled plasmas at 0.01 to 0.1 times solid density for studies of warm dense matter, which is a frontier area in high energy density physics. Pursuit of these near-term objectives has resulted in many innovations that will ultimately benefit heavy ion inertial fusion energy. These include: neutralized ion beam compression and focusing, which hold the promise of greatly improving the stage between the accelerator and the target chamber in a fusion power plant; and the Pulse Line Ion Accelerator (PLIA), which may lead to compact, low-cost modular linac drivers

  11. U.S. Heavy Ion Beam Research for High Energy Density Physics Applications and Fusion

    Davidson, R.C.; Logan, B.G.; Barnard, J.J.; Bieniosek, F.M.; Briggs, R.J.

    2005-01-01

    Key scientific results from recent experiments, modeling tools, and heavy ion accelerator research are summarized that explore ways to investigate the properties of high energy density matter in heavy-ion-driven targets, in particular, strongly-coupled plasmas at 0.01 to 0.1 times solid density for studies of warm dense matter, which is a frontier area in high energy density physics. Pursuit of these near-term objectives has resulted in many innovations that will ultimately benefit heavy ion inertial fusion energy. These include: neutralized ion beam compression and focusing, which hold the promise of greatly improving the stage between the accelerator and the target chamber in a fusion power plant; and the Pulse Line Ion Accelerator (PLIA), which may lead to compact, low-cost modular linac drivers

  12. Physical and chemical investigation of water and sediment of the Keban Dam Lake, Turkey. Part 2. Distribution of radioactivity, heavy metals and major elements

    Kulahci, F.; Dogru, M.

    2006-01-01

    Thirtynine surface water and 20 deep sediment samples were taken in different locations in Keban Dam Lake (Elazig, Turkey) to identify major sources and assess major elements, heavy metals, 137 Cs, 90 Sr, total alpha- and, total beta-distribution in 2003 and 2004 in four seasons each year. As a preliminary study heavy metal (Zn, Fe, Mn, Ni, Cu, Cr, and Co), major element (Mg, Ca, Na, K) and radioactivity concentrations of 137 Cs, 90 Sr, total-α and total-β in the surface water and deep sediments were determined. (author)

  13. Trace elements and heavy metals in mineral and bottled drinking waters on the Iranian market.

    Hadiani, Mohammad Rasoul; Dezfooli-Manesh, Shirin; Shoeibi, Shahram; Ziarati, Parisa; Mousavi Khaneghah, Amin

    2015-01-01

    A survey of Iranian waters, sampled from 2010 to 2013, is presented. A total of 128 water samples from 42 different brands of bottled mineral and drinking water were collected and analysed for contamination levels of lead (Pb), cadmium (Cd), copper (Cu), arsenic (As) and mercury (Hg). Determinations were performed using a graphite furnace atomic absorption spectrophotometer for Pb, Cd and Cu, a hydride vapour generation as well as an Arsenator digital kit (Wagtech WTD, Tyne and Wear, UK) for As and a direct mercury analyser for Hg. Arsenic concentration in six bottled gaseous mineral samples was higher than the related limit. Regardless of these, mean concentrations of Pb, Cd, Cu, As and Hg in all types of water samples were 4.50 ± 0.49, 1.08 ± 0.09, 16.11 ± 2.77, 5.80 ± 1.63 and 0.52 ± 0.03 µg L⁻¹, respectively. Values obtained for analysed heavy metals in all samples were permissible according to the limits of national and international standards.

  14. Heavy metals, metalloids and other hazardous elements in marine plastic litter.

    Turner, Andrew

    2016-10-15

    Plastics, foams and ropes collected from beaches in SW England have been analysed for As, Ba, Br, Cd, Cl, Cr, Cu, Hg, Ni, Pb, Sb, Se, Sn and Zn by field-portable-x-ray fluorescence spectrometry. High concentrations of Cl in foams that were not PVC-based were attributed to the presence of chlorinated flame retardants. Likewise, high concentrations of Br among both foams and plastics were attributed to the presence of brominated flame retardants. Regarding heavy metals and metalloids, Cd and Pb were of greatest concern from an environmental perspective. Lead was encountered in plastics, foams and ropes and up to concentrations of 17,500μgg(-1) due to its historical use in stabilisers, colourants and catalysts in the plastics industry. Detectable Cd was restricted to plastics, where its concentration often exceeded 1000μgg(-1); its occurrence is attributed to the use of both Cd-based stabilisers and colourants in a variety of products. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Heavy metal incorporation in foraminiferal calcite: results from multi-element enrichment culture experiments with Ammonia tepida

    G.-J. Reichart

    2010-08-01

    Full Text Available The incorporation of heavy metals into carbonate tests of the shallow water benthic foraminifer Ammonia tepida was investigated under controlled laboratory conditions. Temperature, salinity, and pH of the culture solutions were kept constant throughout the duration of this experiment, while trace metal concentrations were varied. Concentrations of Ni, Cu, and Mn were set 5-, 10-, and 20 times higher than levels found in natural North Sea water; for reference, a control experiment with pure filtered natural North Sea water was also analysed. The concentrations of Cu and Ni from newly grown chambers were determined by means of both μ-synchrotron XRF and Laser Ablation Inductively Coupled Plasma Mass Spectroscopy (LA-ICP-MS. The results of both independent analytical techniques agreed within the analytical uncertainty. In general, the concentration of the analysed elements in the tests increased in line with their concentration in the culture solutions. Potential toxic and/or chemical competition effects might have resulted in the decreased incorporation of Ni and Cu into the calcite of the specimens exposed to the highest elemental concentrations. Mn incorporation exhibited large variability in the experiment with the 20-fold increased element concentrations, potentially due to antagonistic effects with Cu. The partition coefficients of Cu and Ni were calculated to be 0.14 ± 0.02 and 1.0 ± 0.5, respectively, whereas the partition coefficient of Mn was estimated to be least 2.4. These partition coefficients now open the way for reconstructing past concentrations for these elements in sea water.

  16. Convective parameters in fuel elements for research nuclear reactors

    Lopez Martinez, C.D.

    1992-01-01

    The study of a prototype for the simulation of fuel elements for research nuclear reactors by natural convection in water is presented in this paper. This project is carry out in the thermofluids laboratory of National Institute of Nuclear Research. The fuel prototype has already been test for natural convection in air, and the first results in water are presented in this work. In chapter I, a general description of Triga Mark III is made, paying special atention to fuel-moderator components. In chapter II and III an approach to convection subject in its global aspects is made, since the intention is to give a general idea of the events occuring around fuel elements in a nuclear reactor. In chapter II, where an emphasis on forced convection is made, some basic concepts for forced convection as well as for natural convection are included. The subject of flow through cylinders is annotated only as a comparative reference with natural convection in vertical cylinders, noting the difference between used correlations and the involved variables. In chapter III a compilation of correlation found in the bibliography about natural convection in vertical cylinders is presented, since its geometry is the more suitable in the analysis of a fuel rod. Finally, in chapter IV performed experiments in the test bench are detailed, and the results are presented in form of tables and graphs, showing the used equations for the calculations and the restrictions used in each case. For the analysis of the prototypes used in the test bench, a constant and uniform flow of heat in the whole length of the fuel rod is considered. At the end of this chapter, the work conclusions and a brief explanation of the results are presented (Author)

  17. Research on treatment of wastewater containing heavy metal by microbial fuel cell

    Chen, Zixuan; Lu, Xun; Yin, Ruixia; Luo, Yunyi; Mai, Hanjian; Zhang, Nan; Xiong, Jingfang; Zhang, Hongguo; Tang, Jinfeng; Luo, Dinggui

    2018-02-01

    With rapid development of social economy, serious problem has been caused by wastewater containing heavy metals, which was difficult to be treated by many kinds of traditional treatment methods, such as complex processes, high cost or easy to cause secondary pollution. As a novel biological treatment technology, microbial fuel cells (MFC) can generate electric energy while dealing with wastewater, which was proposed and extensively studied. This paper introduced the working principle of MFC, the classification of cathode, and the research progress on the treatment of wastewater containing Cr(VI), Cu(II), Ag(I), Mn(II) and Cd(II) by MFC. The study found that different cathode, different heavy metals anddifferent hybrid systems would affect the performance of the system and removal effect for heavy metal in MFC. MFC was a highly potential pollution control technology. Until now, the research was still in the laboratory stage. Its industrial application for recovery of heavy metal ion, improving the energy recovery rate and improvement or innovation of system were worthy of further research.

  18. CARA Project: development of the advanced ULE fuel element for heavy water nuclear power plants

    Brasnarof, Daniel O.; Marino, Armando C.; Florido, Pablo C.; Munoz, C.; Bianchi, Daniel R.; Giorgis, Miguel A.

    2006-01-01

    The CARA Project (Spanish acronym of Combustible Avanzado para Reactores Argentinos) is a national fuel element technology development, compatible with our nuclear power plants (Atucha I, Embalse and Atucha II). It takes into account the experience obtained in our nuclear organisations (CNEA-CONUAR-NASA). The goal of the CARA fuel element is the performance improvement for those reactors and the enhancing of their normal operative conditions. The CARA design allows the burnup extension by using 52 rods of the same diameter. Likewise it keeps good thermo-hydraulic behaviour. The fuel bundle can be directly used in nuclear power plants with horizontal channels. By using an additional system it can be installed in the PHWR with vertical channels. The expected profits, by the use of the CARA in our reactors, broadly guaranty the recovery of the fund for its development, due to a reduction of the NPP fuels and back end cost. We estimate a reduction in the generation cost between 20 or 25 % in relation to the present one if we use 0.85 or 0.90% SEU (Slightly Enriched Uranium). The use of the CARA fuel in our reactors will also reduce the amount of spent fuel to be treated. The shortening could be between 17 to 27 % in Atucha I in relation to the present ULE (0.85%), between 38 to 46% for Embalse, and 45 to 53% for Atucha II. The mechanical behaviour and hydraulic compatibility have been verified. Several CARA prototypes were fabricated with a new design of the end plate and with new processes for the welding for the rods. We present in this paper the current status of the CARA fuel element development. (author) [es

  19. Air pollution in Damascus city, radiation, gases, air particulates and heavy elements

    Othman, Ibrahim; Sabra, Shawki

    1991-02-01

    The purposes of the study were to have a general survey for pollutants in Damascus City, to define the polluted areas and to determine the relationship between the pollutants and its sources, in addition of determining the regretion coefficient for the following elements: K, Ca, Mn, Fe, Cu, Zn, Rb, Sr, Pb and Br. Samples of leaves from different regions of Damascus city were analysed by using x-ray flourescence (XRF) for the mentioned elements. Stat graphics computerized and Surfur programmes were used in order to plot the map of Pb pollutant for Damascus city. Chemical detector tubes produced by Drager Company were used in the absorbtion of air samples for Co, NO 2 and ozon where its colours were changed according to the concentration of the interested gases. While, for the measurement of suspended particles, 1400 3 m of air samples were taken through fiber gass filter (Wahtman 8x10 in) to measure the concentration of suspended particles. leaves samples were a good indicator for the level of pollution. Results of analysing, a samples by using XRF to determine the concentration of the following elements: Ca, K, Cu, Mn, Fe, Zn, Pb, Rb, Br, and Sr, by using gamma spectroscopy system to difine the isotopes included in it, and to define the activity of 212 Pb show that dust and lead are the main pollutants in Damascus city, where the concentration of the suspended particles increased in the crowded transportation areas and reach to more than 700 mg/ 3 m in which it decreases in holidays and at hight, as well as the decrease of the concentration of carbon monoxide at night, which increase in the morning due to the high trafic motion. Rains make a good cleaning factor for the suspended particles in about 80% of it, where the ratio of particles having a diameter less than 10μ to the whole particles range from 30% - 80%. (author)., 25 figs., 35 tabs

  20. Summary report of the second research co-ordination meeting on improvement of the standard cross sections for light elements

    Carlson, A.D.; Hale, G.M.; Pronyaev, V.G.

    2004-03-01

    Results are presented following one and a half years of work under the Coordinated Research Project (CRP) on Improvement of the Standard Cross Sections for Light Elements. They include the use of the refined resonating group model for the theoretical prediction of the R-matrix poles and preliminary R-matrix model fits of the full experimental database for the 6 Li+n system obtained with different codes. Significant attention was paid to the exclusion of the bias in the evaluated data caused by the possible presence of Peelle's Pertinent Puzzle effect in the experimental data. Updates were also presented of the experimental database for light and heavy element standards including fission cross sections up to 200 MeV. First results and observed trends for all standard reactions are given, including the preliminary results of combining the model (for light elements) and non-model fits. The timetable for further work was agreed, which should lead to new reaction cross section standards for light and heavy elements by the end 2004. (author)

  1. Compensation of equipment housing elements of reactor units with heavy liquid metal coolant vessel temperature deformations

    Lebedevich, V.; Ahmetshin, M.; Mendes, D.; Kaveshnikov, S.; Vinogradov, A.

    2015-01-01

    In Russia a lot of different versions of fast reactors (FRs) are investigated and one of these is FR cooled by liquid lead and liquid lead-bismuth alloy. In this poster we are interested by FR with concrete vessel; its components are placed in cavities inside the vessel, and connected by a channel system. During the installation the equipment components are placed in several equipment housings. Between these housings there are cavities with coolant. The alignment of the housings should be provided. It can be broken by irregular concrete vessel heating during FR starting or other transition regimes. Our goal is to suggest a list of designing steps to compensate temperature deformations of equipment housing elements. A simplified model of equipment housing was suggested. It consists of two cylinders - tunnels in the concrete vessel, separated by a cavity filled by coolant and inert gas. The bottom part was considered as heated to 420 C. degrees while in the top part temperature decreased to 45 C. degrees (on the concrete surface). According to this data, results show that temperature gradient leads to a concrete layer dislocation of about 12.5 mm, which can lead to damage and breaking alignment. We propose the following solution to compensate for temperature deformation: -) to chisel out part of the upper top of the insulating concrete; -) to install an adequate misalignment of equipment housing elements preliminary; and -) to use a torsion system like a piston-type device for providing additional strength in order to compensate deformation and vibrations

  2. Heavy metals and mineral elements not included on the nutritional labels in table olives.

    López-López, Antonio; López, Rafael; Madrid, Fernando; Garrido-Fernández, Antonio

    2008-10-22

    The average contents, in mg/kg edible portion (e.p.), of elements not considered for nutritional labeling in Spanish table olives were as follows: aluminum, 71.1; boron, 4.41; barium, 2.77; cadmium, 0.04; cobalt, 0.12; chromium, 0.19; lithium, 6.56; nickel, 0.15; lead, 0.15; sulfur, 321; tin, 18.4; strontium, 9.71; and zirconium, 0.04. Sulfur was the most abundant element in table olives, followed by aluminum and tin (related to green olives). There were significant differences between elaboration styles, except for aluminum, tin, and sulfur. Ripe olives had significantly higher concentrations (mg/kg e.p.) of boron (5.32), barium (3.91), cadmium (0.065), cobalt (0.190), chromium (0.256), lithium (10.01), nickel (0.220), and strontium (10.21), but the levels of tin (25.55) and zirconium (0.039) were higher in green olives. The content of contaminants (cadmium, nickel, and tin) was always below the maximum limits legally established. The discriminant analysis led to an overall 86% correct classification of cases (80% after cross-validation).

  3. FINITE ELEMENT ANALYSIS OF CENTRELESS-LUNETTE TURNING OF HEAVY SHAFT

    Yu. V. Vasilevich

    2017-01-01

    Full Text Available Dynamics of huge renovated lathe is simulated. Turning scheme concerns to heavy rotor shaft finishing. Lofty parts and milling head may create dynamic problems. Static, modal and harmonic frequency response function simulations were provided. Bearing system consists of bed, support, tool, lunettes, tailstock. Headstock didn’t take part in shaft holding. Static and dynamic rigidities founded 3–4 times less for support than for shaft. Tool rigidity lessens from 186.5 to 11.9 N/µm for speeding from slow to near resonance turning. Twelve lathe eigenmodes were evaluated. Two eigenmodes are most dangerous. It is “shaft swinging on lunettes” (M1, 26.7 Hz and “support pecking” (M3, 54.4 Hz. Bed has excessive flexibility due to through holes and lack of inner ribbing. Polymer concrete filling is moderately effective. Changing two-lunette (2L scheme to three-lunette (3L increases rigidity of shaft at 2.09 times at statics but gives limited action in dynamics. Resonant peaks on frequency response function are lowered only at 1.32 times for M1, M3. Effect of dynamic damping is revealed under condition of proximity middle lunette to lofty support. Support serves as tuned mass damper. Measures of machine tool reinforcement are simulated. Shaft swinging according to M1 may hardly be blocked by passive means. It would be better to bypass it. “Support pecking” resonance (M3 succumbs to only full set of measures. Small effect of partial reinforcement is predicted. Three frequency intervals are recommended for turn-milling at huge lathe: pre-resonant (<20 Hz, inter-resonant (35–45 Hz and post-resonant (>65 Hz. The last one is more suited. Next design step is to create triangle inner ribbing system or caissons inside of bed.

  4. Determination of heavy metals and other elements in sediments from Sepetiba Bay (RJ, Brazil) by neutron activation analysis

    Pellegatti, Fabio

    2000-01-01

    Sepetiba Bay, located about 60 km south of the city of Rio de Janeiro, Brazil, is one of the most important fishery areas in the State of Rio de Janeiro. A large harbor brought up a lot of industrial investment in that area. Since the 1970's, the Sepetiba region has undergone fast industrial expansion, leading to high levels of pollution by metals. For the last two decades, an industrial park composed of about 400 industrial plants, basically metallurgical, was established in the Sepetiba Bay basin, releasing its industrial waste either straight into the bay or through local rivers. Metal contamination in the bay for some metals, such as Zn, has already exceeded acceptable levels. Many authors have studied the distribution and behavior of heavy metals and another elements in the bay, but only few elements have been focused (Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn). This is probably due to the fact that the analytical technique most employed has been atomic absorption spectrometry, which is not a multi-elemental technique. In this work, Instrumental Neutron Activation Analysis (INAA) was applied to the determination of the elements As, Ba, Br, Ce, Co, Cr, Cs, Eu, Fe, Hf, La, Lu, Nd, Rb, Sc, Sm, Ta, Tb, Th, U, Yb and Zn in 28 bottom sediment samples and four sediment cores from Sepetiba Bay. The elements Co, Cr, Cs, Fe, Sc, Ta and Zn presented similar behavior in the bottom sediments, showing higher concentration along the Northern coast of the bay, where most of the fluvial water flows out to the bay. The contamination of Sepetiba Bay was also assessed by the analysis of four sediment cores. Two of them were sampled in the Eastern part of the bay, where the industrial park is located, whereas the other two were sampled in the Western part of the bay, a more preserved region. For each region, two cores were sampled within the mangrove trees and the others at the edge of the tidal flat. The results showed that, the sediments displayed higher metal concentration within the

  5. Accumulation of heavy metals and trace elements in fluvial sediments received effluents from traditional and semiconductor industries.

    Hsu, Liang-Ching; Huang, Ching-Yi; Chuang, Yen-Hsun; Chen, Ho-Wen; Chan, Ya-Ting; Teah, Heng Yi; Chen, Tsan-Yao; Chang, Chiung-Fen; Liu, Yu-Ting; Tzou, Yu-Min

    2016-09-29

    Metal accumulation in sediments threatens adjacent ecosystems due to the potential of metal mobilization and the subsequent uptake into food webs. Here, contents of heavy metals (Cd, Cr, Cu, Ni, Pb, and Zn) and trace elements (Ga, In, Mo, and Se) were determined for river waters and bed sediments that received sewage discharged from traditional and semiconductor industries. We used principal component analysis (PCA) to determine the metal distribution in relation to environmental factors such as pH, EC, and organic matter (OM) contents in the river basin. While water PCA categorized discharged metals into three groups that implied potential origins of contamination, sediment PCA only indicated a correlation between metal accumulation and OM contents. Such discrepancy in metal distribution between river water and bed sediment highlighted the significance of physical-chemical properties of sediment, especially OM, in metal retention. Moreover, we used Se XANES as an example to test the species transformation during metal transportation from effluent outlets to bed sediments and found a portion of Se inventory shifted from less soluble elemental Se to the high soluble and toxic selenite and selenate. The consideration of environmental factors is required to develop pollution managements and assess environmental risks for bed sediments.

  6. Heavy Ion Fusion Accelerator Research (HIFAR) half-year report, October 1, 1985-March 31, 1986

    1986-05-01

    The HIFAR program addresses the generation of high-power, high-brightness beams of heavy ions, the understanding of the scaling laws in this novel physics regime, and the validation of new accelerator strategies, to cut costs. Key elements to be addressed include: (1) beam quality limits set by transverse and longitudinal beam physics; (2) development of induction accelerating modules, and multiple beam hardware, at affordable costs; (3) acceleration of multiple beams with current amplification - both new features in a linac - without significant dilution of the optical quality of the beams; (4) fianl bunching, transport, and accurate focussing on a small target

  7. Removal of heavy elements from Contaminated Matrices using amidoxime chelating starch

    Shama, S.A.; Wally, S.A.; Aly, H.F.

    2012-01-01

    The synthesis of a amidoxime chelating starch was carried out by grafting of acrylonitrile onto starch using the mutual irradiation techniques at dose rate 2.5 kGy. Conversion of nitrile groups of the grafted copolymer into the amidoxime was carried out by treatment with hydroxylamine under alkaline solution. The amidoxime chelating starch was characterized by FT-IR spectra, TG, Particle size, Surface area, SEM, and Elemental analyses. The chelating behavior of the prepared resin was carried out by using uranium. The binding capacity of uranium ion by the amidoxime resin was carried out by the batch technique. The sorption capacity was high for uranium, 86.9 mg/g at ph 6.5. The kinetic exchange rate was fast. It was observed that the uranium uptake ratio reaches 50% at 10 min (t 1/2 ). The treatment process using amidoxime sorbent is efficient to remove uranium from the waste solution of the FMPP plant.

  8. Neutron activation analysis of heavy metal elements in Chinese medicines and medical herbs

    Furuta, Etsuko; Ishihara, Sachiko; Okumura, Ryou; Iinuma, Yuuto

    2014-01-01

    'Kanpo (Chinese method)' is a kind of traditional Chinese medical science, and 'Kanpo-yaku (Chinese medicines)' is the drugs on the basis of this medical science. The raw materials for Chinese medicines mainly use ingredients derived from nature, such as herbs, parts of living animal body, and ores, and these are collectively referred to as crude drugs. Using instrumental neutron activation analysis, this study performed the qualitative and quantitative analysis of metal elements contained in the Chinese medicines and crude drugs that were obtained from five routes of four countries. It divided totally 119 samples to each purchase root, and summarized the quantitative analytical results with a focus on Cr, Co, As, Sb, and Hg, and found variations in the contents between the natures of the samples. A large amount of As was detected in two samples of 'Oriental bezoar' and 'Liushen pill,' which were purchased from China under doctors' prescriptions. As a result of the analysis of 47 plant samples purchased from Vietnam as the raw materials for Chinese medicines, a higher percentage of Hg was found compared with other samples. This fact suggests that Chinese medicines using medical herbs derived from plants are liable to contains not a little Hg. Large variations in the content of each sample suggest that the contents are dependent on the country of origin, as well as types and parts of plants. As for the samples purchased in Japan, the detected percentages of five target elements were the smallest. (A.O.)

  9. Biomonitoring of heavy metals and trace elements in the Euroregion Neisse

    Markert, B.; Wappelhorst, O.

    1999-01-01

    The Euroregion Neisse, located in Central Europe at the border of Poland, the Czech Republic and Germany, and the area around Katowice, Poland are part of the so-called 'black triangle'. Due to industrial, traffic and household emissions, this region is one of the most highly-polluted areas in central Europe. The extent of the damage caused by the pollution is very visible and makes international improvement and sanitation concepts of vital importance. The long-range objective of this investigation is to determine the degree of pollution using a bioindication system. Mosses (Pleurozium schreberi and Polytrichum formosum) and spruce (Picea abies) and pine (Pinus sylvestris) needles are used as indicators. They are sampled throughout the region and analyzed for select chemical elements by ICP-MS, ICP-OES and AAS in order to determine the distribution of these in the investigation area. By taking samples throughout the area at regular time intervals the development of element concentrations are observed and followed. The data thus gathered is then presented visually using the Geographical Information System (GIS) to make the results more clear and accessible. These results can then form a basis for comparison between the frequency of various diseases in the region and the level and concentration of pollutants and will make correlation between the two evident. The Euroregion Neisse and the Katowice area, with their high environmental pollution, are especially well-suited for such an investigation. They may even be called highly polluted reference areas where the effects of pollution on ecology and health are remarkably visible. (author)

  10. Investor's and procurement guide South Africa. Pt. 1. Heavy minerals, rare earth elements, antimony

    Graupner, Torsten; Schwarz-Schampera, Ulrich; Hammond, Napoleon Q.; Opperman, Rehan; Long'a Tongu, Elisa; Kenan, Abdul O.; Nondula, Unathi; Tsanwani, Matamba

    2014-01-01

    This is the first part of the ''Investor's and Procurement Guide South Africa'', a handbook for investing and doing business in South Africa's mineral industry. It is anticipated that this publication will aid potential investors into considering South Africa as an investment destination, not only for raw materials, but also for related industries. This manual supplements the many publications available on the economic geology and mineral wealth in South Africa and has been designed to guide prospective and current investors, suppliers and mine equipment exporters through the process of doing business in Africa's biggest and dynamic economy. As well as detailing the mineral raw materials heavy minerals, rare-earth metals and antimony, the handbook provides a general introduction to South Africa and its infrastructure, the economical, political and judicial frame of the South African mining industry and an overview of the economic geology. South Africa has a long and complex geological history which dates back in excess of 3.6 billion years. The country has a vast mineral wealth, undoubtedly due to the fact that a significant proportion of the Archaean and younger rocks have been preserved. The mining of the enormous Witwatersrand gold deposits, commencing in 1886, has led to the establishment of South Africa's well-developed infrastructure and to the sustained growth of an industrial and service sector in the country. With the world's largest resources of PGMs, gold, chromite, vanadium and manganese and significant resources of iron, coal and numerous other minerals and metals, the minerals industry will continue to play a pivotal role in the growth of South Africa's economy in the foreseeable future. South Africa is one of the top destinations in Africa for foreign direct investments. South African headquartered companies have been major investors into foreign direct investments on the African continent in the past decade. Investing in South African companies

  11. Biological and medical research with accelerated heavy ions at the Bevalac, 1974--1977

    Elam, S.

    1977-04-01

    The Bevalac, a versatile high-energy heavy-ion accelerator complex, has been in operation for less than two years. A major purpose for which the Bevalac was constructed was to explore the possibility of heavy-ion teams for therapy for certain forms of cancer. Significant progress has been made in this direction. The National Cancer Institute has recognized the advantages that these and other accelerated particles offer, and heavy ions have been included in a long-term plan for particle therapy that will assess by means of controlled therapeutic tests the value of various modalities. Since accelerated heavy ions became available, the possibility of other contributions, not planned, became apparent. We are developig a new diagnostic method known as heavy-ion radiography that has greatly increased sensitivity for soft-tissue detail and that may become a powerful tool for localizing early tumors and metastases. We have discovered that radioactive beams are formed from fragmentation of stable deflected beams. Use of these autoradioactive beams is just beginning; however, we know that these beams will be helpful in localizing the region in the body where therapy is being delivered. In addition, it has been demonstrated that instant implantation of the radioactive beam allows direct measurements of blood perfusion rates in inaccessible parts of the body, and such a technique may become a new tool for the study of fast hot atom reactions in biochemistry, tracer biology and nuclear medicine. The Bevalac will also be useful for the continuation of previously developed methods for the control of acromegaly, Cushing's disease and, on a research basis, advanced diabetes mellitus with vascular disease. The ability to make small bloodless lesions in the brain and elsewhere with heavy-ion beams has great potential for nervous-system studies and perhaps later for radioneurosurgery

  12. Examination of U3Si2-Al fuel elements from the Oak Ridge Research Reactor

    Copeland, G.L.; Snelgrove, J.L.; Hofman, G.L.

    1986-01-01

    The results of postirradiation examination of low-enriched U 3 Si 2 fuel elements from the Oak Ridge Research Reactor are presented. The elements replaced standard high-enriched elements and were handled routinely except that the burnup of half the elements was extended beyond normal limits up to about 98% peak. The elements were manufactured by commercial fuel suppliers. The performance was completely satisfactory for all the elements

  13. 10 GHz multicharged-heavy-ion source CAPRICE for all metallic and gaseous elements

    Bourg, F.; Geller, R.; Jacquot, B.

    1987-01-01

    A new compact multiply charged E.C.R. ion source completely enclosed by an iron return yoke is described. A new coaxial 10 GHz microwave accessibility is operating. This allows a very compact two stages source in an entirely removable vacuum chamber and a very easy increasing possibility of the axial magnetic field value. Then two different working modes are possible. A classical mode (ω ce =ω rf , 100% cw, rf power 300 W, coils supply 20 kW) gives same performance than all the other reliable larger 10 GHz sources. A second mode (100% cw, rf power 600 W, coils supply 33 kW) operates with an additional resonant surface ω ce =2ω rf and increases by a factor 3 or 4 all currents on high charge states. Total extraction current is multiplied by a factor of 4 just as it would do by using a classical 20 GHz source by increase in density. This new resonant surface is unfortunately stopped in its radial part by the wall of the vacuum chamber due to a too low 10 GHz sextupole (0,4 T). Presently a better sextupole (0,8 T) is being built in order to work with both whole resonant surfaces inside the plasma chamber and perhaps so to improve charge states distribution by rising the plasma life time. On the other hand both the removable vacuum chamber and the coaxial rf feeder are well fitted to produce all metallic ions in long run and high intensity by working without any insulator inside the plasma chamber and by a good cleaning possibility. One shows cw spectra of 10 metallic elements from Al to Au and one can observe an exponential decrease for Ca, Ag and Au. This remark indicates a possible easy way to yield high charge states of all metals. One can expect to regulate all the lightest elements like Al, Si, Fe, Ni, Mo, Ta and W for 100 h. For example a good (within 1%) regulation of a 15 μA 56 Fe 7+ for 10 h is partly shown. (orig.)

  14. Hubble Space Telescope observations of cool white dwarf stars: Detection of new species of heavy elements

    Shipman, Harry; Barnhill, Maurice; Provencal, Judi; Roby, Scott; Bues, Irmela; Cordova, France; Hammond, Gordon; Hintzen, Paul; Koester, Detlev; Liebert, James

    1995-01-01

    Observations of cool white dwarf stars with the Hubble Space Telescope (HST) has uncovered a number of spectral features from previouslly unobserved species. In this paper we present the data on four cool white dwarfs. We present identifications, equivalent width measurements, and brief summaries of the significance of our findings. The four stars observed are GD 40 (DBZ3, G 74-7 (DAZ), L 745-46A (DZ), and LDS 749B (DBA). Many additional species of heavey elements were detected in GD 40 and G 74-7. In L 745-46A, while the detections are limited to Fe 1, Fe II, and Mg II, the quality of the Mg II h and K line profiles should permit a test of the line broadening theories, which are so crucial to abundance determinations. The clear detection of Mg II h and k in LDS 749 B should, once an abundance determination is made, provide a clear test of the hypothesis that the DBA stars are the result of accretion from the interstellar medium. This star contains no other clear features other than a tantalizing hint of C II 1335 with a P Cygni profile, and some expected He 1 lines.

  15. Some E.U.V. spectra from laser produced plasma of heavy elements

    Even-Zohar, M.

    1975-09-01

    The spectra of Al, Mo, Ag, In, Sn, Cs, Ba, La, Ce, Ta and W produced by a Nd doped glass laser (energy about 15J, power near 5.10 8 W) were photographed in the region 20-240A utilizing a 3 m grazing incidence spectrograph. The continuum behavior is described. New identifications of Al XI, Mo XVII, Mo XVIII, Ag XII, Ag XVIII, Ag XIX, Ag XX, Ag XXI, In XIV, In XXI, In XXII, In XXIII, Sn XV, Sn XX, Sn XXI, Sn XXII, Sn XXIV, Cs VIII, Cs IX, Cs X, Cs XXVII, Ba IX, Ba X, Ba XI, La X, La XI, La XII and W VII are given. Lists of measured lines of Mo, Ag, Cs, Ba, La, and W are given. The spectra appear as absorption and emission lines where the transition from absorption to emission occurs in the same element for ions with ionization potential of 200 to 350eV. Absorption and emission spectra from the same ion of the same plasma are observed [fr

  16. Effect of silver nanoparticles on concentration of silver heavy element and growth indexes in cucumber (Cucumis sativus L. negeen)

    Shams, Gholamabbas, E-mail: ghs@iaushiraz.net; Ranjbar, Morteza [Shiraz Branch, Islamic Azad University, Department of Physics (Iran, Islamic Republic of); Amiri, Aliasghar [Shiraz Branch, Islamic Azad University, Department of Chemistry (Iran, Islamic Republic of)

    2013-05-15

    The tremendous progress on nanoparticle research area has been made significant effects on the economy, society, and the environment. Silver nanoparticle is one of the most important particles in these categories. Silver nanoparticles can be converted to the heavy silver metal in water by oxidation. Moreover, in the high amounts of silver concentration, they will be accumulated in different parts of the plant. However, by changing the morphology of the plant, the production will be harmful for human consumptions. In this study, nano-powders with average 50 nm silver particles are mixed with deionized distilled water in a completely randomized design. Seven treatments with various concentrations of suspension silver nanoparticles were prepared and repeated in four different parts of the plant in a regular program of spraying. Samples were analyzed to study the growth indexes and concentration of silver in different parts of the plant. It was observed that with increasing concentration of silver nanoparticles on cucumber, the growth indexes (except pH fruit), and the concentration of silver heavy metal are increased significantly. The incremental concentration had the linear relationship with correlation coefficient 0.95 and an average of 0.617 PPM by increasing of each unit in one thousand concentration of nanosilver. Although, by increasing concentration of silver nanoparticles as spraying form, the plant morphological characteristics were improved, the concentration of silver heavy metal in various plant organs was increased. These results open a new pathway to consider the effect of nanoparticles on plant's productions for human consumptions.

  17. MEGHNAD – A multi element detector array for heavy ion collision ...

    of the prototype detector and brief outline of the research programme to be ... Such a nucleus often becomes unstable, and sheds away the extra energy and ... reaction products, and event by event analysis of the nuclear reactions for a .... High voltage is applied at the cathode grid, and the anode is kept at the ground.

  18. Ages and Heavy Element Abundances from Very Metal-poor Stars in the Sagittarius Dwarf Galaxy

    Hansen, Camilla Juul; El-Souri, Mariam; Monaco, Lorenzo; Villanova, Sandro; Bonifacio, Piercarlo; Caffau, Elisabetta; Sbordone, Luca

    2018-03-01

    Sagittarius (Sgr) is a massive disrupted dwarf spheroidal galaxy in the Milky Way halo that has undergone several stripping events. Previous chemical studies were restricted mainly to a few, metal-rich ([Fe/H] \\gtrapprox -1) stars that suggested a top-light initial mass function (IMF). Here we present the first high-resolution, very metal-poor ([Fe/H] =‑1 to ‑3) sample of 13 giant stars in the main body of Sgr. We derive abundances of 13 elements, namely C, Ca, Co, Fe, Sr, Ba, La, Ce, Nd, Eu, Dy, Pb, and Th, that challenge the interpretation based on previous studies. Our abundances from Sgr mimic those of the metal-poor halo, and our most metal-poor star ([Fe/H] ∼ -3) indicates a pure r-process pollution. Abundances of Sr, Pb, and Th are presented for the first time in Sgr, allowing for age determination using nuclear cosmochronology. We calculate ages of 9+/- 2.5 {Gyr}. Most of the sample stars have been enriched by a range of asymptotic giant branch (AGB) stars with masses between 1.3 and 5 M ⊙. Sgr J190651.47–320147.23 shows a large overabundance of Pb (2.05 dex) and a peculiar abundance pattern best fit by a 3 M ⊙ AGB star. Based on star-to-star scatter and observed abundance patterns, a mixture of low- and high-mass AGB stars and supernovae (15–25 M ⊙) is necessary to explain these patterns. The high level (0.29 ± 0.05 dex) of Ca indicates that massive supernovae must have existed and polluted the early ISM of Sgr before it lost its gas. This result is in contrast with a top-light IMF with no massive stars polluting Sgr. Based on data obtained UVES/VLT ID: 083.B-0774, 075.B-0127.

  19. Review of Heavy-Duty Engine Combustion Research at Sandia National Laboratories

    Robert W. Carling; Gurpreet Singh

    2000-01-01

    The objectives of this paper are to describe the research efforts in diesel engine combustion at Sandia National Laboratories' Combustion Research Facility and to provide recent experimental results. We have four diesel engine experiments supported by the Department of Energy, Office of Heavy Vehicle Technologies: a one-cylinder version of a Cummins heavy-duty engine, a diesel simulation facility, a one-cylinder Caterpillar engine to evaluate combustion of alternative fuels, and a homogeneous-charge, compression-ignition (HCCI) engine facility is under development. Recent experimental results to be discussed are: the effects of injection timing and diluent addition on late-combustion soot burnout, diesel-spray ignition and premixed-burn behavior, a comparison of the combustion characteristics of M85 (a mixture of 85% methanol and 15% gasoline) and DF2 (No.2 diesel reference fuel), and a description of our HCCI experimental program and modeling work

  20. Expansion connection of socket in flow distributed cabin of heavy water research reactor inner shell

    Jiang Zhiliang; Li Yanshui

    1995-01-01

    Expansion connection of aluminium alloy LT21 socket in flow distributed cabin of Heavy Water Research Reactor (HWRR) inner shell is described systematically. The expansion connection technology parameters of products are determined through tests. They are as following: bounce value of inner diameter after expansion, expansion degree, space between socket and plate hole, device for expanding pipes, selection of tools for enlarging or reaming holes, manufacture for socket inner hole and cleaning after expansion

  1. Preliminary results from MBE-4: A four beam induction linac for heavy ion fusion research

    Fessenden, T.J.; Judd, D.L.; Keefe, D.; Kim, C.; Laslett, L.J.; Smith, L.; Warwick, A.I.; Warwick, P.b.A.I.

    1986-01-01

    Preliminary results are presented from a scaled experimental multiple beam induction linac. This experiment is part of a program of accelerator research for heavy ion fusion. It is shown that multiple beams can be accelerated without significant mutual interaction. Measurements of the longitudinal dynamics of a current-amplifying induction linac are presented and compared to calculations. Coupling of transverse and longitudinal dynamics is discussed

  2. HAZOP-study on heavy water research reactor primary cooling system

    Hashemi-Tilehnoee, M.; Pazirandeh, A.; Tashakor, S.

    2010-01-01

    By knowledge-based Hazard and Operability (HAZOP) technique, equipment malfunction and deficiencies in the primary cooling system of the generic heavy water research reactor are studied. This technique is used to identify the representative accident scenarios. The related Process Flow Drawing (PFD) is prepared as our study database for this plant. Since this facility is in the design stage, applying the results of HAZOP-study to PFD improves the safety of the plant.

  3. Preliminary results from MBE-4: a four beam induction linac for heavy ion fusion research

    Fessenden, T.J.; Judd, D.L.; Keefe, D.; Kim, C.; Laslett, L.J.; Smith, L.; Warwick, A.I.

    1986-05-01

    Preliminary results are presented from a scaled experimental multiple beam induction linac. This experiment is part of a program of accelerator research for heavy ion fusion. It is shown that multiple beams can be accelerated without significant mutual interaction. Measurements of the longitudinal dynamics of a current-amplifying induction linac are presented and compared to calculations. Coupling of transverse and longitudinal dynamics is discussed

  4. Determination of macro, essential trace elements, toxic heavy metal concentrations, crude oil extracts and ash composition from Saudi Arabian fruits and vegetables having medicinal values

    Hana R. Alzahrani

    2017-11-01

    Full Text Available The concentrations of essential elements (Mg, Ca, Na, K, Fe, Zn, Se, Al, Ni, and Cu and toxic heavy metals (Pb, As, Cr, Cd, and Cr from Saudi Arabian fruits and vegetables were determined by inductively coupled plasma optical emission spectrophotometry (ICP/OES. Two types of butters, Caralluma munbayana and Caralluma hesperidum, Vigna (Vigna unguiculata, common fig (Ficus carica, Annona seeds (Annonaceae seeds, Annona fruits (Annonaceae fruits, Fennel (Foeniculum vulgare, and Fennel flowers (Nigella sativa were investigated, because they are used by indigenous groups as traditional medicines with Soxhlet-extraction and dry-ashing protocol. The estimated daily dietary element intake in food samples was further calculated in order to evaluate the element dietary intake and fruit and vegetable consumption pattern of the indigenes of Saudi Arabia. The crude oil and ash compositions varied widely, but suggested that most of the foods were good sources of oils and minerals. The figures-of-merit of the ICP-OES calibration curves were excellent with good linearity (R2 > 0.9921. The use of ICP-OES in this study allowed the accurate analysis and the detection of the elements at low levels. Essential elements (K, Ca, Na, and Mg had the highest concentrations while toxic heavy metals (As, Pb, and Cd had the lowest in the foods. Essential element pairs (Mg-Na, Mg-Ca, Fe-Al were highly correlated, suggesting that these foods are sources of multiple nutrients. Toxic element pairs (Pb-Cd, Pb-As, and Cd-As, however, were poorly correlated in the foods, suggesting that these elements do not have a common source in these foods. Average consumption of these foods should provide the recommended daily allowances of essential elements, but will not expose consumers to toxic heavy metals. The ICP-OES method was validated by determining method detection limits and percent recoveries of laboratory-fortified blanks, which were generally 90–100%.

  5. Heavy-ion research at the tandem and superconducting linac accelerators

    Anon.

    1980-01-01

    The heavy-ion research program at the Argonne Physics Division is principally aimed at the study of nuclear structure and its manifestation in heavy-ion induced nuclear reactions. In order to extract information on nuclear structure, measurements with high precision often need to be performed. Such measurements are now carried out at the tandem-linac accelerator over a wide energy range. The investigation of high-spin states near the yrast line has provided much new information on the behavior of nuclei at high angular momentum. Argonne work has concentrated on nuclei where high-spin isomers, the so-called yrast traps, are prevalent. The resonance effects observed previously in the 24 Mg( 16 O, 12 C) 28 Si reactions have been further explored through both additional measurements and a new quantitative method of analysis. The measurements were extended in energy and angular range and to various exit channels as well as similar systems. Several measurements were performed to investigate the reaction mechanisms in heavy-ion induced reactions and to map out the distribution of reaction strength as a function of energy and target-projectile masses energy regions previously not accessible. The behavior of the quasi- and deep-inelastic reaction cross sections was studied as a function of energy for medium-heavy systems, the production of inclusive alpha-particle yields for 16 O beams at energies E/A greater than or equal to 5 MeV/nucleon, and excitation functions, mass and kinetic energy distributions for heavy-ion induced fusion-fission reactions

  6. Ethical aspect of the clinical research. Informed consent in the clinical research for heavy ion radiotherapy of cancer

    Murata, Hajime

    2003-01-01

    The research center for heavy ion therapy of cancer was decided to be built in 1984 as a part of the national 10-year anticancer campaign, and construction of Heavy Ion Medical Accelerator in Chiba (HIMAC) was completed at the National Institute of Radiological Sciences in 1993. The HIMAC is the first heavy ion accelerator for only medical use in the world, and the clinical research of cancer radiotherapy was begun in 1994 using carbon ion generated by HIMAC. The purposes of the clinical research are to evaluate the safety and usefulness of carbon ion for cancer treatment, and to establish carbon ion therapy as a new and valuable tool for cancer therapy. Therefore, to obtain exact data in ethical aspect as well as scientific aspect of the clinical research, many special committees have been organized like as the committees of protocol planning for each organ, clinical study groups for each organ, evaluating committee of clinical data, and the ethical committee. Each clinical research is performed according to the research protocol of each organ, in which study purpose, rationale, patient condition, end-point of the study, adverse reaction are described. The document of informed consent (IC) contains study purpose, patient condition, method, predicted effect and demerit, protection of privacy, etc.. IC to each patient is done precisely by the doctor, and the freely-given IC of the patient is obtained. After the IC was completed, judgement of propriety for carbon ion therapy is done by the ethical committee for IC of each patient. Since 1994 carbon ion therapy has been performed over 1300 patients with cancer in various organs, and its safety and usefulness for cancer treatment has been clarified gradually. The carbon ion therapy is thought to be a new and promising tool for cancer treatment near future. (authors)

  7. THE RESEARCH OF THE AMOUNT OF HEAVY METALS AND NITROSO COMPOUNDS IN CONCENTRATED TOMATO PRODUCTS

    V.V. Shutyuk

    2016-12-01

    Full Text Available The constant selling race results in need for improving the quality of nutrition products among in-house food and pharmaceutical processing industries, which is an all-important key to success on the consumer market. This requires constant improvement of the product producing technologies. The topical problem of quality is the presence of heavy metals and nitroso compounds in the products. The research aimed at studying the changes in the heavy metal concentration levels (including Zn, Cu, Pb in tomato products at their thickening has been conducted at the national University of Food Technologies. On the basis of the received results the relationship between the lead, copper, zinc, nitrosocompounds and the solid substances’ amount has been established. The conducted research allowed us to ascertain the fact that the amount of heavy metals and nitroso compounds in raw materials for the concentrated tomato products to be ofhigh quality must not exceed the values of 18…35 % of the limiting concentration.

  8. Research Notes ~ Elements of Effective e-Learning Design

    Andrew R. Brown

    2005-03-01

    Full Text Available Preparing and developing e-learning materials is a costly and time consuming enterprise. This paper highlights the elements of effective design that we consider assist in the development of high quality materials in a cost efficient way. We introduce six elements of design and discuss each in some detail. These elements focus on paying attention to the provision of a rich learning activity, situating this activity within an interesting story line, providing meaningful opportunities for student reflection and third party criticism, considering appropriate technologies for delivery, ensuring that the design is suitable for the context in which it will be used, and bearing in mind the personal, social, and environmental impact of the designed activities. Along the way, we describe how these design elements can be effectively utilized by contextualizing them with examples from an e-learning initiative.

  9. A business process for enhanced heavy oil recovery research and development

    Carlson, P.; Campbell, M.; Kantzas, A.

    1995-01-01

    Husky Oil's enhanced oil recovery (EOR) research management processes for reducing process development time and increasing investment efficiency were described. The considerations that went into the development of the plan a decade ago were reviewed and new ideas incorporated into the revised plan were presented. Four case studies were presented to illustrate the need for process to reservoir matching. A need for strategic research planning was emphasized. Proposed technologies for enhancement of heavy oil reservoir productivity were presented in tabular form. 1 tab., 7 figs

  10. Summary report of the first research co-ordination meeting on improvement of the standard cross sections for light elements

    Carlson, A.D.; Hale, G.M.; Pronyaev, V.G.

    2003-01-01

    Results obtained during the first six months of the Coordinated Research Project (CRP) on Improvement of the Standard Cross Sections for Light Elements were presented. Attention focused on studies of the reduction in uncertainty for the model and non-model least squares fits, intercomparison and testing of different computer codes based on the nuclear model, non-model general least square and Bayesian approaches to the evaluation of standard reaction cross sections and covariance matrix of their uncertainties. The reasons leading to the underestimation of uncertainties and bias in the evaluated values were discussed and solutions to these problems were outlined. A coordinated working plan was prepared which will result in the preparation of new reaction cross section standards for light and heavy elements by 2004. (author)

  11. Emission Control Research to Enable Fuel Efficiency: Department of Energy Heavy Vehicle Technologies

    Gurpreet Singh; Ronald L. Graves; John M. Storey; William P. Partridge; John F. Thomas; Bernie M. Penetrante; Raymond M. Brusasco; Bernard T. Merritt; George E. Vogtlin; Christopher L. Aardahl; Craig F. Habeger; M.L. Balmer

    2000-01-01

    The Office of Heavy Vehicle Technologies supports research to enable high-efficiency diesel engines to meet future emissions regulations, thus clearing the way for their use in light trucks as well as continuing as the most efficient powerplant for freight-haulers. Compliance with Tier 2 rules and expected heavy duty engine standards will require effective exhaust emission controls (after-treatment) for diesels in these applications. DOE laboratories are working with industry to improve emission control technologies in projects ranging from application of new diagnostics for elucidating key mechanisms, to development and tests of prototype devices. This paper provides an overview of these R and D efforts, with examples of key findings and developments

  12. Overview of Heavy Ion Fusion Accelerator Research in the U. S.

    Friedman, Alex

    2002-12-01

    This article provides an overview of current U.S. research on accelerators for Heavy Ion Fusion, that is, inertial fusion driven by intense beams of heavy ions with the goal of energy production. The concept, beam requirements, approach, and major issues are introduced. An overview of a number of new experiments is presented. These include: the High Current Experiment now underway at Lawrence Berkeley National Laboratory; studies of advanced injectors (and in particular an approach based on the merging of multiple beamlets), being investigated experimentally at Lawrence Livermore National Laboratory); the Neutralized (chamber) Transport Experiment being assembled at Lawrence Berkeley National Laboratory; and smaller experiments at the University of Maryland and at Princeton Plasma Physics Laboratory. The comprehensive program of beam simulations and theory is outlined. Finally, prospects and plans for further development of this promising approach to fusion energy are discussed.

  13. Nuclear research with heavy ions. Annual progress report. January 1, 1980-December 31, 1980

    Kaplan, M.

    1980-10-01

    The program of research is oriented towards experimental studies of the interactions between heavy ions and complex nuclei. These interactions are probed by detailed measurements of light-charged-particle emission using counter telescopes for atomic number and mass number identification. Singles measurements of the charged-particle energy spectra and angular distributions, together with coincidence correlations with heavy nuclear-reaction fragments, provide insight into the contributing reaction mechanisms. The application of the statistical model to the appropriate experimental data allows the determination of parameters necessary to calibrate the theory, and gives indications of dynamical control vs. equilibrium in the several degrees of freedom associated with the nuclear collisions. A large body of data are presented and discussed for /sup 40/Ar reactions with /sup 116/Sn, /sup 154/Sm, /sup 164/Dy, and /sup 197/Au targets. Complete results are also given for twelve reactions which produce /sup 194/Hg compound nuclei at several excitation energies.

  14. Overview of heavy ion fusion accelerator research in the U.S

    Friedman, Alex

    2002-01-01

    This article provides an overview of current U.S. research on accelerators for Heavy Ion Fusion, that is, inertial fusion driven by intense beams of heavy ions with the goal of energy production. The concept, beam requirements, approach, and major issues are introduced. An overview of a number of new experiments is presented. These include: the High Current Experiment now underway at Lawrence Berkeley National Laboratory; studies of advanced injectors (and in particular an approach based on the merging of multiple beamlets), being investigated experimentally at Lawrence Livermore National Laboratory); the Neutralized (chamber) Transport Experiment being assembled at Lawrence Berkeley National Laboratory; and smaller experiments at the University of Maryland and at Princeton Plasma Physics Laboratory. The comprehensive program of beam simulations and theory is outlined. Finally, prospects and plans for further development of this promising approach to fusion energy are discussed

  15. Overview of Heavy Ion Fusion Accelerator Research in the U.S

    Friedman, A

    2002-01-01

    This article provides an overview of current U.S. research on accelerators for Heavy Ion Fusion, that is, inertial fusion driven by intense beams of heavy ions with the goal of energy production. The concept, beam requirements, approach, and major issues are introduced. An overview of a number of new experiments is presented. These include: the High Current Experiment now underway at Lawrence Berkeley National Laboratory; studies of advanced injectors (and in particular an approach based on the merging of multiple beamlets), being investigated experimentally at Lawrence Livermore National Laboratory; the Neutralized (chamber) Transport Experiment being assembled at Lawrence Berkeley National Laboratory; and smaller experiments at the University of Maryland and at Princeton Plasma Physics Laboratory. The comprehensive program of beam simulations and theory is outlined. Finally, prospects and plans for further development of this promising approach to fusion energy are discussed

  16. Bioavailability of heavy metals, germanium and rare earth elements at Davidschacht dump-field in mine affected area of Freiberg (Saxony)

    Midula, Pavol; Wiche, Oliver

    2016-04-01

    Bioavailability research presents an essential tool, in modern phytoremediation and phytomining technologies, allowing the estimation of plant available fractions of elements in soils. However, up to date, sufficient interdisciplinary knowledge on the biogeochemically impacted behavior of specific target elements, in particular Ge and REEs in mining affected soils and their uptake into strategically used plants is lacking. This presented work is focused on a correlation study between the concentrations of selected heavy metals, Ge and REEs in soils formed on the top of the dump-field of Davidschacht and the corresponding their concentrations in 12 vascular plant species. The mine-dump of Davidschacht, situated in the Freiberg (Saxony, Germany) municipality area was chosen as the study area, which has been considered to be a high contaminated enclave, due to the mining history of the region. In total 12 sampling sites with differing composition of plant species were selected. At each sampling site soil samples from a soil depth of 0 - 10 cm and samples of plant material (shoots) were taken. The soil samples were analysed for total concentration of elements, pH (H2O) and consequently analysed by 4-step sequential extraction (SE) to determine fractions of elements that are mobile (fraction 1), acid soluble (pH 5) (fraction 2), bound to organic and oxidizable matter (fraction 3) and bound to amorphic oxides (fraction 4). The plant material was decomposed by hydrofluoric acid in order to extract the elements. Concentrations of elements in soil extracts and digestion solutions were analysed by ICP-MS. For all species bioconcentration factor (BCF) was calculated of the total concentration of elements in order to investigate the bioaccumulation potential. Arsenic (As), cadmium (Cd) and lead (Pb) were chosen as the representative heavy metals. Within the REEs neodymium (Nd) and cerium (Ce) were selected as representatives for all REEs, since Nd and Ce correlated significant

  17. Comments on the current status and possible future directions of research on heavy-ion interactions near the Coulomb barrier

    Satchler, G.R.

    1990-01-01

    This paper contains comments on the current status and possible future directions of research on heavy-ion interactions near the Coulomb barrier. Fusion reactions, elastic and inelastic scattering and transfer reactions are discussed

  18. Nuclear research with heavy ions. Annual progress report, January 1, 1979-December 31, 1979

    Kaplan, M.

    1979-10-01

    The experimental research emphasizes the detection and measurement of light charged particles emitted in reactions between heavy ions and complex nuclei. The program involves a collaboration between Carnegie-Mellon University and SUNY at Stony Brook, and utilizes the SuperHILAC and 88'' cyclotron accelerator facilities of the Lawrence Berkeley Laboratory. Correlations between light charged particles and heavy fragments provide detailed insights into the dynamics of the reaction mechanism. The light charged particles evaporated from fully accelerated fragments yield information on the excitation energies and spins of the equilibrated reaction products, whereas those particles that are emitted prior to thermal equilibration give a view of the early stages of the reaction. Experimental results of fusion and charged particle emission cross sections are discussed for a variety of heavy ion reactions, particularly those induced by 40 Ar ions. The theoretical development of the statistical model as applied to particle evaporation is reviewed, and semiempirical methods for facilitating comparisons with experimental data are presented. Current results from singles and coincidence experiments are given in detail for reactions of 340-MeV 40 Ar with Au, and analyses of average spins and energy sharing among particles are discussed

  19. Relativistic heavy ions from the BNL [Brookhaven National Laboratory] booster medical research and technological applications

    Thieberger, P.

    1990-05-01

    The BNL Booster, now nearing completion, was designed to inject protons and heavy ions into the Alternating Gradient Synchrotron (AGS) for further acceleration. In the future, ion beams from the AGS will in turn be further accelerated in the Relativistic Heavy Ion Collider (RHIC). Given the wide range of ion masses, energies and beam intensities the Booster will generate, other important applications should be considered. Dedicated use of the Booster for such applications may be possible during limited periods. However shared use would be preferable from the points of view of availability, affordability and efficiency. While heavy ions of a given isotope are injected into the AGS, the same or other ion species from the Booster could be simultaneously delivered to a new irradiation area for treatment of patients, testing of electronic devices or other applications and research. To generate two different beam species, ion sources on both Tandem accelerators would be used; one for AGS injection and the other one for a time-sharing application. Since the beam transport from the Tandems to the Booster can not be rapidly adjusted, it will be necessary to select beams of identical magnetic rigidity. The present study was performed to determine to what extent this compatibility requirement imposes limitations on the available ion species, energies and/or intensities

  20. Elements in biological AMS

    Vogel, J.S.; McAninch, J.; Freeman, S.

    1996-08-01

    AMS (Accelerator Mass Spectrometry) provides high detection sensitivity for isotopes whose half-lives are between 10 years and 100 million years. 14 C is the most developed of such isotopes and is used in tracing natural and anthropogenic organic compounds in the Earth's biosphere. Thirty-three elements in the main periodic table and 17 lanthanides or actinides have long lived isotopes, providing potential tracers for research in elemental biochemistry. Overlap of biologically interesting heavy elements and possible AMS tracers is discussed

  1. USING OF THE MATHEMATICAL STATISTICS METHODS FOR THE CHARACTERISTIC OF THE ELEMENTAL CONTAMINATION URBAN ECOSYSTEMS SOILS BY THE HEAVY METALS

    YAKOVYSHYNA T. F.

    2017-03-01

    Full Text Available Summary. Raising of problem. Sustainable development of the urban ecosystems, taking into account the provision of ecological safety standards for the human life within the city and the rational use and restoration of the resource potential of the territory, requires the search for effective methods of the characteristic of the ecological situation. In the conditions of the progressive pressure to the environment, the leading role belongs to the mathematical statistics methods, as a tool that allows us to examine and analyze in detail ecological systems of the various complexity. Of all the environmental abiotic components, soils have been given the least attention, which is due, firstly, to the ambiguous characteristic of the environmental situation according to the total content of the contaminant, and secondly, to the problem of choice its additional forms for the statistical analysis. Purpose. Substantial using of the mathematical statistics methods in the ecomonitoring system along with the generally accepted for the characterization of the elemental soil contamination of the urban ecosystem by the heavy metals, by determining the statistical characteristics and establishing relationships between the total content, potentially available and available forms by the example of Zn contamination in the Dnieper. The total content, potentially available and available forms have been used to determine the elemental Zn contamination. An array of the content data of the studied Zn forms has been obtained in the network of ecological monitoring of soils of the Dnieper urban ecosystem: grid (2 km × 2 km, key sampling sites – 65. In the selected samples, the Zn total content yas been determined by the atomic absorption method after acidizing the soil, its potentially available forms in the extraction of 1 H HCl, and the available forms in AAB (pH 4.8 by standard methods. The mathematical statistics methods and the application package Microsoft Excel

  2. The origin of secondary heavy rare earth element enrichment in carbonatites: Constraints from the evolution of the Huanglongpu district, China

    Smith, M.; Kynicky, J.; Xu, Cheng; Song, Wenlei; Spratt, J.; Jeffries, T.; Brtnicky, M.; Kopriva, A.; Cangelosi, D.

    2018-05-01

    The silico‑carbonatite dykes of the Huanglongpu area, Lesser Qinling, China, are unusual in that they are quartz-bearing, Mo-mineralised and enriched in the heavy rare earth elements (HREE) relative to typical carbonatites. The textures of REE minerals indicate crystallisation of monazite-(Ce), bastnäsite-(Ce), parisite-(Ce) and aeschynite-(Ce) as magmatic phases. Burbankite was also potentially an early crystallising phase. Monazite-(Ce) was subsequently altered to produce a second generation of apatite, which was in turn replaced and overgrown by britholite-(Ce), accompanied by the formation of allanite-(Ce). Bastnäsite and parisite where replaced by synchysite-(Ce) and röntgenite-(Ce). Aeschynite-(Ce) was altered to uranopyrochlore and then pyrochlore with uraninite inclusions. The mineralogical evolution reflects the evolution from magmatic carbonatite, to more silica-rich conditions during early hydrothermal processes, to fully hydrothermal conditions accompanied by the formation of sulphate minerals. Each alteration stage resulted in the preferential leaching of the LREE and enrichment in the HREE. Mass balance considerations indicate hydrothermal fluids must have contributed HREE to the mineralisation. The evolution of the fluorcarbonate mineral assemblage requires an increase in aCa2+ and aCO32- in the metasomatic fluid (where a is activity), and breakdown of HREE-enriched calcite may have been the HREE source. Leaching in the presence of strong, LREE-selective ligands (Cl-) may account for the depletion in late stage minerals in the LREE, but cannot account for subsequent preferential HREE addition. Fluid inclusion data indicate the presence of sulphate-rich brines during alteration, and hence sulphate complexation may have been important for preferential HREE transport. Alongside HREE-enriched magmatic sources, and enrichment during magmatic processes, late stage alteration with non-LREE-selective ligands may be critical in forming HREE

  3. Research of Distribution of Elements in Natural Waters of the Selenga River Pool

    Ganbold, G; Gerbish, S; Dalhsuren, B; Bayarmaa, Z; Maslov, O D; Sevastiyanov, D V

    2001-01-01

    The distribution of heavy metals in natural waters of the Selenga river pool was investigated. The contents of elements were determined using X-ray analysis with complete external reflection (XRACER). The zones with excess of the average contents of elements in comparison with reference samples were found out, that specifies their pollution by metals. It is offered in these zones to organize the regular water quality monitoring for supervision over the condition of the water ecosystems and to carry out actions on decrease of anthropogenous load and pollution of natural waters.

  4. [MONITORING OF THE CONTENT OF HEAVY METALS AND ELEMENTS IN THE SNOW COVER IN AGRICULTURAL SOILS AT THE TERRITORY OF THE MOSCOW REGION].

    Ermakov, A A; Karpova, E A; Malysheva, A G; Mikhaylova, R I; Ryzhova, I N

    2015-01-01

    The monitoring of snow cover pollution by heavy metals and elements (zinc, copper, lead, cadmium, arsenic, nickel, chromium, strontium, manganese, fluorine, lithium) was performed in 20 districts of the Moscow region in 2009, 2012 and 2013. The assessment of the levels of contamination by heavy metals and elements was given by means of comparison of them with the average values in the snow cover near Moscow in the end of the last century and in some areas of the world, that no exposed to technological environmental impact. 7 districts of Moscow region were characterized by a high content of lead and cadmium in the snow water. It requires the control of water, soil and agricultural products pollution.

  5. Proceedings of the workshop on prospects for research with radioactive beams from heavy ion accelerators

    Nitschke, J.M.

    1984-04-01

    The SuperHILAC Users Executive Committee organized a workshop on Prospects for Research with Radioactive Beams from Heavy Ion Accelerators. The main purpose of the workshop was to bring together a diverse group of scientists who had already done experients with radioactive beams or were interested in their use in the future. The topics of the talks ranged from general nuclear physics, astrophysics, production of radioactive beams and high energy projectile fragmentation to biomedical applications. This publication contains the abstracts of the talks given at the workshop and copies of the viewgraphs as they were supplied to the editor

  6. A new digital pulse power supply in heavy ion research facility in Lanzhou

    Wang, Rongkun; Chen, Youxin; Huang, Yuzhen; Gao, Daqing; Zhou, Zhongzu; Yan, Huaihai; Zhao, Jiang; Shi, Chunfeng; Wu, Fengjun; Yan, Hongbin; Xia, Jiawen; Yuan, Youjin

    2013-11-01

    To meet the increasing requirements of the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), a new digital pulse power supply, which employs multi-level converter, was designed. This power supply was applied with a multi H-bridge converters series-parallel connection topology. A new control model named digital power supply regulator system (DPSRS) was proposed, and a pulse power supply prototype based on DPSRS has been built and tested. The experimental results indicate that tracking error and ripple current meet the requirements of this design. The achievement of prototype provides a perfect model for HIRFL-CSR power supply system.

  7. Software architecture to manage data acquisition for the Holifield Heavy-Ion Research Facility

    Atkins, W.H.

    1982-01-01

    Data acquisition for atomic and nuclear physics experiments requires that many different functions be involved in data handling in real-time. Although each experiment requires the same basic functions, many require an amount of customizing. The wide use of the Holifield Heavy Ion Research Facility demands that data acquisition software be flexible enough to accommodate a variety of experiment configurations and custom processing with minimal work. This paper discusses a software implementation which allows customizing and reconfiguring within a standard structure and standard user interface

  8. STUDIES AND RESEARCHES ON TYPHA LATIFOLIA’S (BULRUSH ABSORPTION CAPACITY OF HEAVY METALS FROM THE SOIL

    ALEXANDRA-DANA CHIŢIMUŞ 1*, CRISTIAN RADU 1, 2, VALENTIN NEDEFF 1, EMILIAN MOŞNEGUŢU 1, NARCIS BÂRSAN 1

    2016-12-01

    Full Text Available The research aimed to determine Typha latifolia’s (bulrush absorption capacity of heavy metals from the soil in the industrial area of Piatra Neamt city, Romania. Heavy metals present in ecological systems are available to the absorption process only partially, depending on the type of pH of the environment, their chemical composition, and the quantity of heavy metals in the soil, plants, sediments, water, or air. The choice of sampling points (the industrial area of Piatra Neamt city took into consideration the areas where the pollution sources are located and where the sediment layer is thick and the granularity level is lower than 63 μm. The investigation of Typha latifolia’s absorption capacity showed that, in case of nickel, chromium, copper and arsenic, a very low capacity of heavy metals absorption was detected. Typha latifolia’s highest absorption capacity of heavy metals from the soil was recorded in case of cadmium.

  9. Determination of trace elements and heavy metals in agricultural products cultivated at the Rimac river valley in Lima city using nuclear and related analytical techniques

    Bedregal, Patricia; Torres, Blanca; Olivera, Paula; Mendoza, Pablo; Ubillús, Marco; Creed-Kanashiro, H.; Penny, M.; Junco, J.; Ganoza, L.

    2004-01-01

    There are strong indications that the Rimac river valley is being contaminated with heavy metals and an excess of trace elements that come from some industrial and mining activities developed along the Rimac river valley. The agricultural products cultivated there in could be suffering the same effect. Nuclear and related analytical techniques will play an important role in the study of pollution by providing information concerning the degree of contamination in some agricultural products cul...

  10. Heavy metal and trace element contents in edible muscle of three commercial fish species, and assessment of possible risks associated with their human consumption in Saudi Arabia

    Sabry Mohamed El-Bahr

    2015-09-01

    Full Text Available Three different highly consumed fish species from Al-Ahsa market, Saudi Arabia namely Spangled emporer (Lethriuns nebulosus, Red striped seabream (Pagrus major and Black seabream (Spondyliosoma cantharus were evaluated for their muscle contents of heavy metals (e.g., Cd and Pb and trace elements (e.g., Cu, Zn, Fe and Mn. The possible risks associated with their human consumption were also studied. A total of 60 fresh fish samples comprising of 20 samples from each above mentioned fish were collected, and were subjected for determination of heavy metal and trace element contents by Atomic Absorption Spectrophotometry after Microwave Wet Digestion. The results showed that, accumulation patterns of the heavy metals and trace elements followed the order: Fe > Zn > Cu > Mn > Pb > Cd. There were variations among metal contents in the muscles of the three fish species; S. cantharus accumulated the highest levels of Cu, Zn and Mn, while the highest level of Fe could be detected in the muscles of P. major. The concentration of Cd and Pb remained comparable in the muscles of all three fish species. The calculated maximum daily intake (MDI values were found as 0.0003, 0.0009, 0.0035, 0.0001, 0.0000, 0.0000 mg/day/person for Cu, Zn, Fe, Mn, Cd and Pb, respectively. Conclusively, the present study indicated that, fish muscles contain relatively less burden of heavy metals and trace elements, and no health problem can be raised from human consumption of the examined commercial fishes at Al-Ahsa market, Saudi Arabia. [J Adv Vet Anim Res 2015; 2(3.000: 271-278

  11. Multi-element sewer slime impact pattern--a quantitative characteristic enabling identification of the source of heavy metal discharges into sewer systems.

    Kintrup, J; Wünsch, G

    2001-11-01

    The capability of sewer slime to accumulate heavy metals from municipal wastewater can be exploited to identify the sources of sewage sludge pollution. Former investigations of sewer slime looked for a few elements only and could, therefore, not account for deviations of the enrichment efficiency of the slime or for irregularities from sampling. Results of ICP-MS multi element determinations were analyzed by multivariate statistical methods. A new dimensionless characteristic "sewer slime impact" is proposed, which is zero for unloaded samples. Patterns expressed in this data format specifically extract the information required to identify the type of pollution and polluter quicker and with less effort and cost than hitherto.

  12. Br-rich tips of calcified crab claws are less hard but more fracture resistant: a comparison of mineralized and heavy-element biological materials.

    Schofield, Robert M S; Niedbala, Jack C; Nesson, Michael H; Tao, Ye; Shokes, Jacob E; Scott, Robert A; Latimer, Matthew J

    2009-06-01

    We find that the spoon-like tips of the chelipeds (large claws) of the crab Pachygrapsus crassipes differ from the rest of the claw in that they are not calcified, but instead contain about 1% bromine--thus they represent a new example of a class of structural biological materials that contain heavy elements such as Zn, Mn, Fe, Cu, and Br bound in an organic matrix. X-ray absorption spectroscopy data suggest that the bromine is bound to phenyl rings, possibly in tyrosine. We measure a broad array of mechanical properties of a heavy-element biological material for the first time (abrasion resistance, coefficient of kinetic friction, energy of fracture, hardness, modulus of elasticity and dynamic mechanical properties), and we make a direct comparison with a mineralized tissue. Our results suggest that the greatest advantage of bromine-rich cuticle over calcified cuticle is resistance to fracture (the energy of fracture is about an order of magnitude greater than for calcified cuticle). The greatest advantage relative to unenriched cuticle, represented by ant mandible cuticle, is a factor of about 1.5 greater hardness and modulus of elasticity.The spoon-like tips gain additional fracture resistance from the orientation of the constituent laminae and from the viscoelasticity of the material. We suggest that fracture resistance is of greater importance in smaller organisms, and we speculate that one function of heavy elements in structural biological materials is to reduce molecular resonant frequencies and thereby increase absorption of energy from impacts.

  13. Grain boundary engineering in sintered Nd-Fe-B permanent magnets for efficient utilization of heavy rare earth elements

    Loewe, Konrad

    2016-10-18

    The first part of the thesis investigates the diffusion of rare-earth (RE) elements in commercial sintered Nd-Fe-B based permanent magnets. A strong temperature dependence of the diffusion distance and resulting change in magnetic properties were found. A maximum increase in coercivity of ∼+350 kA/m using a Dy diffusion source occurred at the optimum annealing temperature of 900 C. After annealing for 6 h at this temperature, a Dy diffusion distance of about 4 mm has been observed with a scanning Hall probe. Consequently, the maximum thickness of grain boundary diffusion processed magnets with homogeneous properties is also only a few mm. The microstructural changes in the magnets after diffusion were investigated by electron microscopy coupled with electron probe microanalysis. It was found that the diffusion of Dy into sintered Nd-Fe-B permanent magnets occurs along the grain boundary phases, which is in accordance with previous studies. A partial melting of the Nd-Fe-B grains during the annealing process lead to the formation of so - called (Nd,Dy)-Fe-B shells at the outer part of the grains. These shells are μm thick at the immediate surface of the magnet and become thinner with increasing diffusion distance towards the center of the bulk. With scanning transmission electron microscopy coupled with electron probe analysis a Dy content of about 1 at.% was found in a shell located about 1.5 mm away from the surface of the magnet. The evaluation of diffusion speeds of Dy and other RE (Tb, Ce, Gd) in Nd-Fe-B magnets showed that Tb diffuses significantly faster than Dy, and Ce slightly slower than Dy, which is attributed to differences in the respective phase diagrams. The addition of Gd to the grain boundaries has an adverse effect on coercivity. Exemplary of the heavy rare earth element Tb, the nano - scale elemental distribution around the grain boundaries after the diffusion process was visualized with high resolution scanning transmission electron microscopy

  14. The Research Status and Progress of Heavy/Large Hydrostatic Thrust Bearing

    Xibing Li

    2014-03-01

    Full Text Available How to improve the rotation speed of heavy/large CNC vertical lathe, the machining efficiency, and machining precision is one of the key issues which need to be solved urgently. Hydrostatic thrust bearing is the key part to the heavy/large CNC vertical lathe; its performance directly affects the machining quality and operation efficiency. This paper analyses the latest research results from the perspective of the mechanical properties of hydrostatic thrust bearing, oil film lubrication, static pressure bearing thermal deformation, and the high efficiency refrigeration and evaluates the future scientific research direction in this area. Analysis shows that with the development of hydrostatic thrust bearing to the high speed, high precision, high efficiency, high stability, high multifunction, and high power, the study of hydrostatic thrust bearing will focus on the optimal design of the oil chamber to produce the least amount of heat, how to control the thermal deformation of hydrostatic thrust bearing, and the high efficiency refrigeration to ensure the machining accuracy of CNC equipment.

  15. Radioactivity of heavy minerals and geochemistry of trace elements and radon, resulting from the weathering of the ophiolitic complex, Northwest of Syria

    Kattaa, B.; Al-Hilal, M.; Jubeli, Y.

    1999-06-01

    Geochemical and radiometric survey of stream sediments resulting from the weathering of ophiolitic complex at Al-Basit area were carried out. Several exploration techniques have been used to evaluate the radioactive elements and minerals in the area, and to estimate the significance of the radioactivity of the source rocks of these elements and minerals. determination of radioelements and some trace elements in stream sediments, in addition to gamma-ray spectrometry and radon gas measurement in water of springs and wells were carried out in the study area. The results show that the high values of radioactive elements and radon concentration are related to the occurrence of syenite nepheline and plageogranite, characterized by higher content of these elements compared to mafic and ultramafic rocks. Mineralogical study of the heavy minerals shows that the abundant minerals are pyroxene and amphibole, while less abundant minerals are iron oxides (limonite and hematite), chromite, ilmenite, olivine and magnetite. Rare minerals are zircon, apatite, barite, tourmaline and sphen. The absence of monazite, xenotime and thorite in the collected samples is mainly attributed to the very limited occurrence of their source rocks. However, this results is rather restricted to the collected samples. High concentration of magnetite and ilmenite in some samples was noted, in addition to the presence of mineral called galaxite which was not reported previously. Gold flake was also found in one of the samples. The study of grain morphology suggests that the heavy minerals were transported for short distance from their source rocks. Grain size analyse of heavy minerals reveals that the concentration of economic minerals such as chromite and ilmenite increases with the decrease of the grain size. (author)

  16. Distribution and behaviour of selected heavy metals and other elements in various components of the southern Baltic ecosystem

    Szefer, P.

    1998-01-01

    The concentrations and discrimination of selected heavy metals in biota from the southern Baltic indicate that a large group of the Baltic organisms bioaccumulates Fe and Pb but discriminates against U. There appears to be no significant transfer of heavy metals along successive levels of the food chain. The distribution of the heavy metals in the associated sediments is a result of the anthropogenic input of Zn, Pb, Cd, Ag, P and Cu. It is suggested that Pb is introduced to the Polish sector of the Baltic Sea mainly by atmospheric transport whereas other heavy-metal pollutants are introduced mainly from the Vistula River. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  17. Research activities of Samsung Heavy Industries in the conservation of the environment

    Han, B.; Kim, D.K.; Pikaev, A.K.

    1998-01-01

    Research activities for accelerator fields at Samsung Heavy Industries could be categorized into the accelerator development and its industrial applications. As the initial step of the efforts, high voltage industrial electron accelerators are developed, and development of synchrotron light source and other accelerators are also investigated. The research activities for the applications of accelerator include wastewater treatment, combustion flue gas purification, semiconductor treatment, and other radio-chemical processing. For wastewater treatment, an electron beam pilot plant for treating 1,000m 3 /day of wastewater from 60,000m 3 /day of total dyeing wastewater is under construction in Taegu Dyeing Industrial Complex. A commercial plant for re-circulation of wastewater from papermill company is also under construction in S-paper Co. in Cheongwon city, and after the successful installation, up to 80% of wastewater could be re-used in paper producing process

  18. Intermediate energy heavy ions: An emerging multi-disciplinary research tool

    Alonso, J.R.

    1988-10-01

    In the ten years that beams of intermediate energy (∼50 MeV/amu≤E≤∼2 GeV/amu) heavy ions (Z≤92) have been available, an increasing number of new research areas have been opened up. Pioneering work at the Bevalac at the Lawrence Berkeley Laboratory, still the world's only source of the heaviest beams in this energy range, has led to the establishment of active programs in nuclear physics, atomic physics, cosmic ray physics, as well as biology and medicine, and industrial applications. The great promise for growth of these research areas has led to serious planning for new facilities capable of delivering such beams; several such facilities are now in construction around the world. 20 refs., 5 figs., 1 tab

  19. Evaluation of endcap welds in thin walled fuel elements of pressurised heavy water reactor by ultrasonic testing

    Subramanian, C.V.; Thavasimuthu, M.; Kalyansundaram, P.; Bhattacharya, D.K.; Raj, Baldev

    1992-01-01

    In the pressurised heavy water reactor systems of India, the fuel is encapsulated in thin-walled tubes (0.342 mm) closed with endcaps by resistance welding. The integrity of these fuel elements should be such that no fission gas leakage takes place during reactor operation. The quality control of the endcap welds needed to satisfy this requirement includes helium leak test and destructive metallographic test (on sample basis). This paper discusses the feasibility study that has been carried out in the author's laboratory to develop an immersion ultrasonic test method for evaluating the integrity of the endcap weld region. Through holes of various sizes (0.15mm, 0.2mm, 0.4mm diameter and 0.185mm and 0.342mm deep) were machined by spark erosion machining at the weld joints to simulate defects of various sizes. Line focussed probe of 10 MHz frequency was used for the testing. It was possible to detect clearly all the machined holes. Based on the above standardised procedure, further testing was done on endcap welds which were rejected during fabrication on account of showing leak rate of 3 x 10 -6 std. c.c/sec. or more during helium leak test. Though it was possible to get echoes from the natural defects in the rejected tubes with echo amplitude of 70%, the signal was accompanied by the geometrical reflection (noise) giving an amplitude of 20% from the weld region, giving rise to the problem of resolving the defect indication from the geometric indications. Therefore, signal analysis approach was adopted. The signal obtained from the weld zone were subjected to various analysis procedures like a) autopower spectrum, b) total energy content and c) demodulated auto correlation function. It was possible by all the three methods to differentiate the defect signal from those due to weld geometry or due to noise. Subsequently, metallography was carried out to characterise the type of defects observed during the ultrasonic testing. (author). 4 figs

  20. FEATURES OF THE RESEARCH WORK ELEMENTS DEFORMABILITY OF RAILWAY TRACK

    I. O. Bondarenko

    2015-06-01

    Full Text Available Purpose. The scientific paper is supposed the determination of basic physical and structural conditions in modeling life cycle of the elements of the railway line for the study of deformation processes as the basis of normative base of the track at the condition of railway safety. Methodology. To achieve the aim principles of the elasticity theory and wave propagation process in the description of the interaction between the track and rolling stock were used. Findings. The basic physical and structural conditions under which it is necessary to carry out the simulation of the life cycle of the elements of the railway line for the study of deformation processes were determined. The basic physical and structural principles of drawing the design schemes of railway track elements for the process assessment of the track deformation work were formulated. The decision correctness and the possibility of the problem solution are proved. Originality. The study of the track reliability questions motivates the development of new models, allow considering it for some developments. There is a need to identify the main physical and structural conditions for assembly design schemes based on assessment and prediction of possible track state changes during its operation. The paper presents the basic principles of physical and structural drafting design schemes of railway line items for which Huygens’ principle is implemented. This principle can be performed only when the four dimensional space: the volume changing over time is considered. Practical value. Analytical models applied in determining the parameters of strength and resistance lines, fully satisfy the task, but can not be used to determine the parameters of track reliability. One of the main impossibility factors of these models is quasidynamic approach. Therefore, as a rule, receive and examine not only dynamic process of a railway track, but also its consequences. Besides, these models are related to

  1. Human Research Program: Space Human Factors and Habitability Element

    Russo, Dane M.

    2007-01-01

    The three project areas of the Space Human Factors and Habitability Element work together to achieve a working and living environment that will keep crews healthy, safe, and productive throughout all missions -- from Earth orbit to Mars expeditions. The Advanced Environmental Health (AEH) Project develops and evaluates advanced habitability systems and establishes requirements and health standards for exploration missions. The Space Human Factors Engineering (SHFE) Project s goal is to ensure a safe and productive environment for humans in space. With missions using new technologies at an ever-increasing rate, it is imperative that these advances enhance crew performance without increasing stress or risk. The ultimate goal of Advanced Food Technology (AFT) Project is to develop and deliver technologies for human centered spacecraft that will support crews on missions to the moon, Mars, and beyond.

  2. Perspectives for nuclear structure research at GSI: from halo nuclei to superheavy elements

    Muenzenberg, G.

    1997-11-01

    After a brief overview on recent advances in the investigation of nuclei at the driplines and the upper end of the nuclear table key issues of nuclear structure research as adressed by new theoretical developments will be discussed in context with new developments in heavy-ion accelerators and experimental techniques. (orig.)

  3. Perspectives for nuclear structure research at GSI--from halo nuclei to superheavy elements

    Munzenberg, G.

    1997-01-01

    After a brief overview on recent advances in the investigation of nuclei at the drip lines and the upper end of the nuclear table key issues of nuclear structure research as addressed by new theoretical developments will be discussed in context with new developments in heavy-ion accelerators and experimental techniques

  4. The experiment and research on the migration of the heavy metal

    He Zhijie; Le Renchang; Jia Wenyi; Fang Fang

    2007-01-01

    A device available to observe the heavy metal's migration is designed. We discovered that mixed with α-radioactive source such as U, Th etc., the heavy metal processes the obvious upward migration ability because of α-disintegration. The heavy metals and He nuclei can come into being Cluster. When the specific gravity of Clusters is smaller than that of the air, the Clusters of the heavy metal have the ability of upward migration. (authors)

  5. Research Progress of Microfluidic Chips Preparation and its Optical Element

    Feng WANG

    2014-03-01

    Full Text Available Microfluidic technology is the emerging technologies in researching fluid channel and related applications in the micro and nano-scale space. Microfluidic chip is a new miniaturized rapid analysis platform by microfluidic technology, it has many characteristics such as liquid flow control, minimal reagent consumption, rapid analysis, which is widely used in physics, chemistry, biology, and engineering science and other fields, it has strong interdisciplinary. This paper mainly discusses research progress of materials used for microfluidic chips and the devices based on microfluidic technology, including microfluidic chip, microfluidic optical devices, microfluidic laser preparation, microfluidic chip applications, focusing on the quasi-molecular laser processing technology and femtosecond laser processing technology in the microfluidic devices preparation, and make development prospects for it.

  6. Data acquisition and analysis system for the Holifield Heavy Ion Research Facility

    Milner, W.T.; Biggerstaff, J.A.; Hensley, D.C.; Sayer, R.O.

    1979-01-01

    The Holifield Heavy Ion Research Facility is a national resource which will serve a large number of nuclear and atomic physicists who expect to perform experiments which vary widely in type and complexity. Although much consideration must be given to the problem of rapid acquisition and processing of many-parameter data, an equal emphasis will be placed on operational simplicity and the standardization of hardware and software. Two active experimental counting areas and two or more setup areas are served by three remotely located Perkin--Elmer 8/32 computers which are interfaced to the user equipment by means of three CAMAC branch highways. Other equipment includes a large disk system, alphanumeric/graphic terminals and printer--plotters located in each of the counting areas. The system operation as well as techniques for the rapid sorting of data into large (approx. 10 million channels) histograms on disk are discussed

  7. Operation and utilization of low power research reactor critical facility for Advanced Heavy Water Reactor (AHWR)

    De, S.K.; Karhadkar, C.G.

    2017-01-01

    An Advanced Heavy Water Reactor (AHWR) has been designed and developed for maximum power generation from thorium considering large reserves of thorium. The design envisages using 54 pin MOX cluster with different enrichment of "2"3"3U and Pu in Thoria fuel pins. Theoretical models developed to neutron transport and the geometrical details of the reactor including all reactivity devices involve approximations in modelling, resulting in uncertainties. With a view to minimize these uncertainties, a low power research reactor Critical Facility was built in which cold clean fuel can be arranged in a desired and precise geometry. Different experiments conducted in this facility greatly contribute to understand and validate the physics design parameters

  8. Current developments and future challenges in physics analyses of the NRU heavy water research reactor

    Nguyen, S.; Wilkin, B.; Leung, T., E-mail: nguyens@aecl.ca, E-mail: leungt@aecl.ca [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

    2011-07-01

    The National Research Universal (NRU) reactor is heavy water cooled and moderated, with on-power fueling capability. TRIAD, a 3D two-group diffusion code, is currently used for support of day-to-day NRU operations. Recently, an MCNP full reactor model of NRU has been developed for benchmarking TRIAD. While reactivity changes and flux and power distributions from both methods are in reasonably good agreement, MCNP appears to eliminate a k-eff bias in TRIAD. Beyond TRIAD's capability, MCNP enables the assessment of radiation in the NRU outer structure. Challenges include improving TRIAD accuracy and MCNP performance, as well as performing NRU core-following using MCNP. (author)

  9. Heavy-Section Steel Technology Program: Recent developments in crack initiation and arrest research

    Pennell, W.E.

    1991-01-01

    Technology for the analysis of crack initiation and arrest is central to the reactor pressure vessel fracture-margin-assessment process. Regulatory procedures for nuclear plants utilize this technology to assure the retention of adequate fracture-prevention margins throughout the plant operating license period. As nuclear plants age and regulatory procedures dictate that fracture-margin assessments be performed, interest in the fracture-mechanics technology incorporated into those procedures has heightened. This has led to proposals from a number of sources for development and refinement of the underlying crack-initiation and arrest-analysis technology. This paper presents an overview of ongoing Heavy-Section Steel Technology (HSST) Program research aimed at refining the fracture toughness data used in the analysis of fracture margins under pressurized-thermal-shock loading conditions. 33 refs., 13 figs

  10. Progress in heavy ion driven inertial fusion energy: From scaled experiments to the integrated research experiment

    Barnard, J.J.; Ahle, L.E.; Baca, D.; Bangerter, R.O.; Bieniosek, F.M.; Celata, C.M.; Chacon-Golcher, E.; Davidson, R.C.; Faltens, A.; Friedman, A.; Franks, R.M.; Grote, D.P.; Haber, I.; Henestroza, E.; Hoon, M.J.L. de; Kaganovich, I.; Karpenko, V.P.; Kishek, R.A.; Kwan, J.W.; Lee, E.P.; Logan, B.G.; Lund, S.M.; Meier, W.R.; Molvik, A.W.; Olson, C.; Prost, L.R.; Qin, H.; Rose, D.; Sabbi, G.-L.; Sangster, T.C.; Seidl, P.A.; Sharp, W.M.; Shuman, D.; Vay, J.-L.; Waldron, W.L.; Welch, D.; Yu, S.S.

    2001-01-01

    The promise of inertial fusion energy driven by heavy ion beams requires the development of accelerators that produce ion currents (∼100's Amperes/beam) and ion energies (∼1-10 GeV) that have not been achieved simultaneously in any existing accelerator. The high currents imply high generalized perveances, large tune depressions, and high space charge potentials of the beam center relative to the beam pipe. Many of the scientific issues associated with ion beams of high perveance and large tune depression have been addressed over the last two decades on scaled experiments at Lawrence Berkeley and Lawrence Livermore National Laboratories, the University of Maryland, and elsewhere. The additional requirement of high space charge potential (or equivalently high line charge density) gives rise to effects (particularly the role of electrons in beam transport) which must be understood before proceeding to a large scale accelerator. The first phase of a new series of experiments in Heavy Ion Fusion Virtual National Laboratory (HIF VNL), the High Current Experiments (HCX), is now being constructed at LBNL. The mission of the HCX will be to transport beams with driver line charge density so as to investigate the physics of this regime, including constraints on the maximum radial filling factor of the beam through the pipe. This factor is important for determining both cost and reliability of a driver scale accelerator. The HCX will provide data for design of the next steps in the sequence of experiments leading to an inertial fusion energy power plant. The focus of the program after the HCX will be on integration of all of the manipulations required for a driver. In the near term following HCX, an Integrated Beam Experiment (IBX) of the same general scale as the HCX is envisioned. The step which bridges the gap between the IBX and an engineering test facility for fusion has been designated the Integrated Research Experiment (IRE). The IRE (like the IBX) will provide an

  11. Heavy-Section Steel Technology Program: Recent developments in crack initiation and arrest research

    Pennell, W.E.

    1991-01-01

    Technology for the analysis of crack initiation and arrest is central to the reactor pressure vessel fracture-margin-assessment process. Regulatory procedures for nuclear plants utilize this technology to assure the retention of adequate fracture-prevention margins throughout the plant operating license period. As nuclear plants age and regulatory procedures dictate that fracture-margin assessments be performed, interest in the fracture-mechanics technology incorporated into those procedures has heightened. This has led to proposals from a number of sources for development and refinement of the underlying crack-initiation and arrest-analysis technology. An important element of the Heavy-Section Steel Technology (HSST) Program is devoted to the investigation and evaluation of these proposals. This paper presents the technological bases and fracture-margin assessment objectives for some of the recently proposed crack-initiation and arrest-technology developments. The HSST Program approach to the evaluation of the proposals is described and the results and conclusions obtained to date are presented

  12. Appendix to the report of the Committee on 'Nuclear Physics and Heavy Ion Research' 1983-1985

    1987-04-01

    In the appendix to the scientific report of the research project of the West German Ministry of Research and Technology on 'Nuclear physics and heavy ion research', publications are compiled which have been published on individual projects in the three years of research. Only articles from journals were included, in order to keep the size of this index within reason. The table is compiled in alphabetical sequence of the universities involved. (orig./HP) [de

  13. Research on Elemental Technology of Advanced Nuclear Fuel Performance Verification

    Kim, Yong Soo; Lee, Dong Uk; Jean, Sang Hwan; Koo, Min

    2003-04-01

    Most of current properties models and fuel performance models used in the performance evaluation codes are based on the in-pile data up to 33,000 MWd/MtU. Therefore, international experts are investigating the properties changes and developing advanced prediction models for high burn-up application. Current research is to develop high burn-up fission gas release model for the code and to support the code development activities by collecting data and models, reviewing/assessing the data and models together, and benchmarking the selected models against the appropriate in-pile data. For high burn-up applications, two stage two step fission gas release model is developed based on the real two diffusion process in the grain lattice and grain boundaries of the fission gases and the observation of accelerated release rate in the high burn-up. It is found that the prediction of this model is in excellent agreement with the in-pile measurement results, not only in the low burn-up but also in the high burn-up. This research is found that the importance of thermal conductivity of oxide fuel, especially in the high burn-up, is focused again. It is found that even the temperature dependent models differ from one to another and most of them overestimate the conductivity in the high burn-up. An in-pile data benchmarking of high LHGR fuel rod shows that the difference can reach 30%∼40%, which predicts 400 .deg. C lower than the real fuel centerline temperature. Recent models on the thermal expansion and heat capacity of oxide fuel are found to be well-defined. Irradiation swelling of the oxide fuel are now well-understood that in most cases in LWRs solid fission product swelling is dominant. Thus, the accumulation of in-pile data can enhance the accuracy of the model prediction, rather than theoretical modeling works. Thermo-physical properties of Zircaloy cladding are also well-defined and well-understood except the thermal expansion. However, it turns out that even the

  14. Application of stable isotopes in ecological research : it's all elemental

    Rogers, K.M.

    2005-01-01

    Stable isotopes have been used traditionally in the physical sciences, primarily in geochemistry, sedimentology, and oceanography. Increasingly, however, stable isotopes are also being used in the biological sciences. Application of stable isotopes in ecological studies can provide new and innovative ways of examining a host of topics of fundamental importance to biologists. These topics include, among others, feeding ecology and food webs, nutrient flow and assimilation, habitat use, migration patterns, and distribution and discrimination of species subpopulations. Furthermore, ecological research with isotopes can be applied at many levels (i.e. tissue and organ, whole animal, population, community, and ecosystem). (author). 38 refs., 2 figs

  15. Fuel research for subcritical and critical GEN-IV systems cooled by heavy liquid metal

    Sobolev, V.; Verwerft, M.

    2009-01-01

    The participation of the Belgian Nuclear Research Centre SCK-CEN in the worldwide GEN-IV research can be considered as an opportunity. Today's GEN-IV research at SCK-CEN is mainly driven by the interests of the project MYRRHA (Multipurpose hYbrid Research Reactor for High-tech Applications). The main goal of this project is to build at SCK-CEN in Mol a new generation fast spectrum, subcritical, research and materials testing reactor MYRRHA driven by a high-energy proton accelerator. This GEN-IV MTR is cooled by heavy liquid metal (Pb-Bi) and will be used for the ADS concept demonstration, testing and qualification of new fuels, transmutation targets and innovative materials. On the European scale, MYRRHA is integrated in the Euratom FP6 Integrated Project (IP) EUROTRANS (EUROpean research programme for TRANSmutation of high level nuclear waste in an accelerator driven system), as the small-scale experimental machine for transmutation demonstration called XT-ADS. Last but not least, this experimental facility will also demonstrate the technological feasibility of the LFR (Lead-cooled Fast Reactor) GEN-IV concept; in EU the LFR design studies are performed in the framework of the Euratom FP6 ELSY (European Lead-cooled SYstem) project, where SCK-CEN is a partner. Among the research needed to ensure a safe and reliable operation of the MYRRHA/XT ADS reactor, the development and qualification of fuel and cladding materials have been recognized as one of the main key issues to be addressed

  16. Role of nuclear analytical probe techniques in biological trace element research

    Jones, K.W.; Pounds, J.G.

    1985-01-01

    Many biomedical experiments require the qualitative and quantitative localization of trace elements with high sensitivity and good spatial resolution. The feasibility of measuring the chemical form of the elements, the time course of trace elements metabolism, and of conducting experiments in living biological systems are also important requirements for biological trace element research. Nuclear analytical techniques that employ ion or photon beams have grown in importance in the past decade and have led to several new experimental approaches. Some of the important features of these methods are reviewed here along with their role in trace element research, and examples of their use are given to illustrate potential for new research directions. It is emphasized that the effective application of these methods necessitates a closely integrated multidisciplinary scientific team. 21 refs., 4 figs., 1 tab

  17. [Study on distribution of five heavy metal elements in different parts of Cordyceps sinensis by microwave digestion ICP-MS].

    Zhou, Li; Hao, Qing-Xiu; Wang, Sheng; Yang, Quan; Kang, Chuan-Zhi; Yang, Wan-Zhen; Guo, Lan-Ping

    2017-08-01

    The contents of five heavy metals (Cu, Pb, As, Cd, Hg) in 17 batches of Cordyceps sinensis were determined by microwave digestion-ICP-MS, and their distribution in C. sinensis were analyzed. The results showed that the contents of Cu, Pb, Cd and Hg in all batches were in accordance with the international standards of Chinese Medicine-Chinese Herbal Medicine Heavy Metal Limit, with their contents in the stroma higher than that in the caterpillar body, and the excess rate of As, which mainly concentrated in the caterpillar body part of C. sinensis, was 88.24%, as the content of As in the caterpillar body was 7 to 12 fold of that in the stroma. In this study, the distribution of five heavy metals in C. sinensis was clarified, and the existing problems of arsenic limit of heavy metal in C. sinensis were analyzed, and some suggestions were put forward. It is hoped that the reference standard can be provided for the limited standard of arsenic in C. sinensis. Copyright© by the Chinese Pharmaceutical Association.

  18. Techniques for the research on mass deposition effects in the bio-materials induced by heavy ion implantation

    Yuan Shibin; Wei Zengquan; Li Qiang

    2002-01-01

    Researchers have used heavy ion beams to implant small biomolecules, followed by advanced instrumental analysis to make preliminary studies on mass deposition induced by ion implantation. But research reports on the biological effects, i.e. mass deposition effects induced by mass deposition in living tissues, cells and macro-biomolecules have not been delivered hitherto. In the near future radioactive heavy ion beams will be possible to implant living cells and biomolecules, and auto-radiography, radioactive measurements and molecular biological techniques will be employed to further studies on the effects

  19. Geochemical radioactive investigation of beach sands and stream sediments, using heavy minerals, trace elements and radon measurements, (Qerdaha sheet of the Syrian coast)

    Jubeli, Y.; Kattaa, B.; Al-Hilal, M.

    2000-05-01

    Reconnaissance geochemical radiometric survey of stream sediments resulting from the weathering of outcropped rocks in and around the study area was performed. This survey included heavy mineral sampling, trace and radioelements and radon measurements to evaluate the radioactivity of the source rocks and to understand the nature and distribution of the heavy minerals and trace elements in the study area. Several techniques were used to achieve these objectives. The results of heavy mineral geochemical survey show that the abundant minerals are iron oxides (magnetite, hematite, goehtite and limonite) pyroxene and olivine; less abundant minerals are apatite, ilmenite, garnet, barite, siderite and gloconite, while rare minerals are zircon and rutile. Amphibole is reported as an abundant mineral in sand dunes and is less abundant in samples located in the northern part of the study area. The amphibole seems to be derived from the ophiolitic complex north of the study area. Grain size analysis of heavy minerals revealed that the concentration of economic minerals such as zircon rutile and ilmenite increases with the decrease of the grain size. The microscopic study showed fragments and fossils of foraminifere mostly impregnated with heavy metals such as iron and manganese resulting from diagenetic metasomatism and replacement processes of. Fish teeth (< 2 mm) and oolite of iron were also noticed in most of the samples. The morphology of heavy mineral grains shows that most of the grains are angular to subangular suggesting that they were transported for short distance from their source rocks. Normally, phosphate pellets, gloconite and iron ooids are not considered since their original morphological features show clear roundness that attributed to their sedimentological origin, not to transportation factor. The source rock of most of the heavy mineral assemblage is the basalt. Apatite and gloconite are derived from the phosphorite and phosphatized limestone encountered

  20. Behavior of new complexes of tetrakis(4-methoxylphenyl)porphyrin with heavy rare earth elements in reversed-phase high performance liquid chromatography.

    Zhang, Jun-Feng; Wang, Hong; Hou, An-Xin; Wang, Chang-Fa; Zhang, Hua-Shan

    2004-08-01

    An HPLC method has been developed for the separation of new complexes of tetrakis(4-methoxylphenyl)porphyrin (TMOPP) with four heavy rare earth elements (RE = Y, Er, Tm, and Yb). The function of amine and acid in the mobile phase has been investigated and a reasonable explanation is presented. Successful separation of the RE-TMOPP-Cl complexes is accomplished in 10 min with a mobile phase consisting of methanol-water-acetic acid-triethanolamine. The detection limits (S/N= 3) for the four complexes are 0.01 microg/mL. This method is rapid, sensitive, and simple.

  1. Assessment of atmospheric deposition of heavy metals and other elements in Belgrade using the moss biomonitoring technique and neutron activation analysis.

    Anicić, Mira; Frontasyeva, Marina V; Tomasević, Milica; Popović, Aleksandar

    2007-06-01

    This study aimed at assessing atmospheric deposition of heavy metals and other elements using the moss genera Brachythecium sp. (B. rutabulum and B. salebrosum) and Eurhynchium sp. (E. hians and E. striatum) collected in autumn 2004 in the urban area of Belgrade. The concentrations of 36 elements (Na, Mg, Al, Cl, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Zn, As, Se, Br, Rb, Sr, Mo, Sb, I, Cs, Ba, La, Ce, Sm, Tb, Dy, Hf, Ta, W, Hg, Th, U) were determined in moss and local topsoil samples by instrumental neutron activation analysis. The concentration of elements in moss positively correlated to those obtained for topsoil. High enrichment factors for As, Zn, Mo, Br, Sb, Se, Hg and Cl, calculated to continental crust composition, gave an evidence for anthropogenic impact on urban area, mainly due to intensive vehicular traffic and fossil fuel combustion. The concentration of elements in moss, characteristic for fossil fuel combustion, obtained in this study were substantially lower than in the previous investigation (2000) conducted in the area of Belgrade. The level of concentrations for V, Cr, Ni, and As in moss from this study correlated to those measured for neighboring countries, and were several times higher than the base-level data from low polluted areas. The level of accumulated elements in both investigated moss genera were similar and all studied species could be combined for biomonitoring purposes in urban areas.

  2. Assessment of atmospheric deposition of heavy metals and other elements in Belgrade using the moss biomonitoring technique and neutron activation analysis

    Anicic, M.; Tomasevic, M.; Frontas'eva, M.V.; Popovic, A.

    2006-01-01

    The study aimed at assessing atmospheric deposition of heavy metals and other elements using the moss genera Brachythecium sp. (B. rutabulum and B. salebrosum) and Eurhynchium sp. (E. hians and E. striatum) collected in autumn 2004 in the urban area of Belgrade. The concentrations of 36 elements (Na, Mg, Al, Cl, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Zn, As, Se, Br, Rb, Sr, Mo, Sb, I, Cs, Ba, La, Ce, Sm, Tb, Dy, Hf, Ta, W, Hg, Th, U) were determined in moss and local topsoil samples by instrumental neutron activation analysis. The concentration of elements in moss positively correlated to those obtained for topsoil. High enrichment factors for As, Zn, Mo, Br, Sb, Se, Hg, and Cl, calculated to continental crust composition, gave an evidence for anthropogenic impact on urban area, mainly due to intensive vehicular traffic and fossil fuel combustion. The concentrations of elements in moss, characteristic for fossil fuel combustion, obtained in this study, were substantially lower than in the previous investigation (2000) conducted in the area of Belgrade. The level of concentrations for V, Cr, Ni, and As in moss from this study correlated to those measured for neighboring countries, and were several times higher than the base-level data from low polluted areas. The level of accumulated elements in both investigated moss genera were similar and all studied species could be combined for biomonitoring purposes in urban areas

  3. Nuclear techniques for toxic elements in foodstuffs. Report on an IAEA co-ordinated research programme

    1994-01-01

    The document includes 10 final reports on the IAEA Co-ordinated Research Programme on Nuclear Techniques for Toxic Elements in Foodstuffs. A separate abstract was prepared for each report. Refs, figs and tabs

  4. Nuclear techniques for toxic elements in foodstuffs. Report on an IAEA co-ordinated research programme

    NONE

    1994-12-31

    The document includes 10 final reports on the IAEA Co-ordinated Research Programme on Nuclear Techniques for Toxic Elements in Foodstuffs. A separate abstract was prepared for each report. Refs, figs and tabs.

  5. Online Tutoring Procedure for Research Project Supervision: Management, Organization and Key Elements

    Darder Mesquida, Antònia; Pérez Garcias, Adolfina

    2015-01-01

    Research project tutoring appears as a crucial element for teaching; it is a planned action based on the relationship between a tutor and a student. This paper presents the findings of a design and development research which has as its main aim to create an organization system for the tutoring of online research projects. That system seeks to…

  6. The Elements of Library Research: What Every Student Needs to Know

    George, Mary W.

    2008-01-01

    To do solid academic research, college students need to look beyond the computer search engine. This short, practical book introduces students to the important components of the information-seeking process. "The Elements of Library Research" provides a foundation for success in any research assignment, from a freshman paper to a senior thesis.…

  7. Directions of development of research methods in the assessment of leaching of heavy metals from mineral waste

    Król Anna

    2016-01-01

    Full Text Available There are many test methods to assess the level of the release of heavy metals into the environment from mineral waste materials. Leaching methods can be different depending on the leaching time periods, leaching dynamics, sample preparation method or the pH of the elution medium. In Poland, little attention is paid to the research on the relationship between the leaching of particular heavy metals from mineral wastes and changes in environmental conditions, including the pH of the environment. Tests being carried out abroad have started to pay great attention to the pH-dependent impact of the environment and the liquid being in contact with the material on the degree of leaching contaminants from wastes. The solubility of all metals depends on the value of the pH. Authors of the paper will try to prove that Polish methods of waste characterization is incomplete and inconsistent with opinions prevailing in the global literature. The procedure described in the Polish standards are insufficient to determine the actual level of leaching of heavy metals having regard to the impact of multiple external conditions on the level of leaching of heavy metals. Paper will present a directions of development of research methods in the assessment of leaching of heavy metals from mineral waste.

  8. Multi-element sewer slime impact pattern - a quantitative characteristic enabling identification of the source of heavy metal discharges into sewer systems

    Kintrup, J. [Chemistry Lab., Wessling GmbH, Hannover (Germany); Wuensch, G. [Lehrgebiet Analytische Chemie, Univ. Hannover (Germany)

    2001-11-01

    The capability of sewer slime to accumulate heavy metals from municipal wastewater can be exploited to identify the sources of sewage sludge pollution. Former investigations of sewer slime looked for a few elements only and could, therefore, not account for deviations of the enrichment efficiency of the slime or for irregularities from sampling. Results of ICP-MS multi element determinations were analyzed by multivariate statistical methods. A new dimensionless characteristic ''sewer slime impact'' is proposed, which is zero for unloaded samples. Patterns expressed in this data format specifically extract the information required to identify the type of pollution and polluter quicker and with less effort and cost than hitherto. (orig.)

  9. THE SLOWING DOWN OF THE CORROSION OF ELEMENTS OF THE EQUIPMENT OF HEAVY MET-ALS AT ELEVATED TEMPERATURES

    Носачова, Юлія Вікторівна; Ярошенко, М. М.; Корзун, А. О.; КОРОВЧЕНКО, К. С.

    2017-01-01

    In this article examined the heavy metals ions and their ability to slow down the corrosion process also the impact of ambient temperature on their effectiveness. Solving the problem of corrosion will reduce the impact of large industrial enterprises on the environment and minimize the economic costs. To do this, plants should create a system without a discharge of waste water that is closed recycling systems, which result is a significant reduction in intake of fresh water from natural sourc...

  10. Prospective utilization of accelerated heavy ions in basic and applied research

    Flerov, G.; Oganesyan, Yu.

    1982-01-01

    Some important and interesting trends of heavy ion physics are briefly presented, such as giant processes which are characterized by fundamental restructuring of nuclear systems containing hundreds of nucleons, the mechanism of heavy nuclei interaction, the study of nuclear matter compression, the study of the specificity of heating and thermal conductivity of nuclear matter, the study of heavy ion/nucleus interactions at energies of 200 to 300 MeV/nucleon when the meson degree of freedom becomes manifest, the possibility of the production of ions with a large excess or deficiency of neutrons, new possibilities for determining the fission barrier, the critical verification of fundamental physical concepts of quantum electrodynamics and other possibilities of using accelerated heavy ions. The significance of heavy ion physics for the development of acceleration technologies is also described. (B.S.)

  11. Environmental impacts of heavy metals, rare earth elements and natural radionuclides in marine sediment from Ras Tanura, Saudi Arabia along the Arabian Gulf.

    El-Taher, Atef; Alshahri, Fatimh; Elsaman, Reda

    2018-02-01

    Ras Tanura city is one of the most important cities in Saudi Arabia because of the presence of the largest and oldest oil refinery in the Middle East which was began operations in September 1945. Also its contains gas plant and two ports. The concentration of natural radionuclides, heavy metals and rare earth elements were measured in marine sediment samples collected from Ras Tanura. The specific activities of 238 U, 226 Ra, 232 Th, 40 K and 137 Cs (Bq/kg) were measured using A hyper-pure Germanium detector (HPGe), and ranged from (20.4 ± 4.0-55.1 ± 9.9), (6.71 ± 0.7-46.1 ± 4.5), (3.51 ± 0.5-18.2 ± 1.5), (105 ± 4.4-492 ± 13) and from (0.33 ± 0.04-2.10 ± 0.4) for 238 U, 226 Ra, 232 Th, 40 K and 137 Cs respectively. Heavy metals and rare earth elements were measured using ICPE-9820 Plasma Atomic Emission Spectrometer. Also the frequency distributions for all radioactive variables in sediment samples were analyzed. Finally the radiological hazards due to natural radionuclides in marine sediment were calculated to the public and it's diagramed by Surfer program in maps. Comparing with the international recommended values, its values found to be within the international level. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Application of the Rutherford backscattering analysis (RBS analysis) for detecting heavy impurity elements in pBN crucible materials

    Bethge, K.; Meyer, J.D.; Michelmann, R.; Krauskopf, J.

    1992-01-01

    By means of the Rutherford backscattering analysis evidence is given of an inhomogeneous depth distribution of the elements C, O, F, Na, Mg, Al, Si, P, S, Cl, Ca, Ti, Cr, Fe, Ni in pBN (pyrolytic boron nitride) materials of crucibles. This inhomogenous distribution is observed both at the original surface and at the surface of inner cracks. In addition, the distribution of the elements is found to differ depending on the spots chosen for analysis. The RBS measurements alone do not yield information on the volume concentration of the elements. (orig.) With 2 refs [de

  13. Research and design of pulsed switching power supply for deep tumor therapy facility with heavy ions accelerator in Lanzhou

    Shi Chunfeng; Zhao Jiang; Yan Hongbin; Wu Fengjun; Gao Daqing

    2012-01-01

    The pulsed switching power supply was developed for deep tumor therapy facility with heavy ions in cooler-storage-ring of the heavy ions research facility in Lanzhou (HIRFL-CSR). The control principle of the dual closed-loop scheme was described and the open-loop Bode diagrams were given. The results of simulation and prototype experiment show that the current error gets much smaller than that of the single closed-loop pulsed switching power supply. Moreover, the simulation and test results were analyzed, and the circuit configuration and dual closed-loop strategy selected are practicable. (authors)

  14. Research and design of scanning power supply for deep tumor therapy facility with heavy ions accelerator in Lanzhou

    Huang Yuzhen; Liu Yuntao; Chen Youxin; Gao Daqing; Zhang Shu; Gao Yalin

    2009-01-01

    This paper describes the technique targets and operation principle of the scanning power supply for the deep tumor therapy facility with heavy ions in Cooler-Storage-Ring of the Heavy Ion Research Facility in Lanzhou (HIRFL-CSR). To ensure the specified accuracy of the current, the hysteresis loop control strategy was adopted, and tracking error was constrained in the specified tolerance. One prototype was designed and installed. And the simulation results and test results were listed in the paper. The results show that all the targets can meet the design requirements, and that the circuit configuration and hysteresis loop control strategy selected are practicable. (authors)

  15. An interactive, multitask computer system for heavy-ion physics research with the spin spectrometer: [Progress report, 1982

    Sarantites, D.G.

    1982-01-01

    The scope of this proposal is to assemble an interactive off-line data analysis system based on a DEC VAX 11/780 computer interfaced with an array processor, which is capable of meeting the needs of modern heavy-ion physics experiments involving data of large dimensionality as created in the Spin Spectrometer at the Holifield Heavy-ion Research Facility, to adapt the existing PDP 11 software for the Spin Spectrometer for this computer system in a form completely compatible with other laboratories with VAX 11 computers, and to develop new general and efficient software for automatic but fully interactive data analysis making use of an attach array processor

  16. Research Analysis of Vermicompost Influence on Bioaccumulation of Heavy Metals in Common Meadow-Grass (Poa pratensis

    Domas Laurinaitis

    2016-10-01

    Full Text Available The more intensive growth of agricultural crops adding mineral fertilizers, environmental pollution make the soil degraded: reduce the fertility of soil, increase the concentration of heavy metals. Especially dangerous is a common, synergistic effect of heavy metals. Vermicompost optimizes pH, texture and organic material content – the soil indicators, which are the major contributors to migration of heavy metals in the soil and to the plants from it. In the article there is an investigation of vermicompost influence on bioaccumulation of heavy metals in common meadow-grass. After experimental research it is determined that immobilization of heavy metals was the best in soil-vermicompost substrate, prepared in a ratio 1:2. The cadmium (Cd concentrations were lowest and the difference of HM content determined between roots and shoots was the most in biomass grown up in that mixture. In the underground part of plant the concentration equal to 11.10 mg/kg and in the part of above ground – 1.05 mg/kg. The situation of lead (Pb and copper (Cu is analogous. This is the optimal ratio of mixture preparation.

  17. SAFARI-1 research reactor beryllium reflector element replacement, management and relocation

    Kock, Marisa De; Vlok, Jwh; Steynberg, B J [South Africa Atomic Energy Corporation (Necsa) (South Africa)

    2012-03-15

    The beryllium (Be) reflector elements of the SAFARI-1 Research Reactor were replaced in October 2011 as part of the Ageing Management Programme of the reactor. After more than three million MWh of operation over a period of 47 years, core reloading became more difficult due to the geometric deformation of the beryllium reflector elements. During the replacement of the reflector elements, criticality and reactivity worth experiments were performed and found to compare favorably with calculated values. A Beryllium Management Programme was established at SAFARI-1 to identify and apply effective and appropriate actions and practices for managing the ageing of the new beryllium reflector elements. This will provide timely detection and mitigation of ageing mechanisms relevant to beryllium reflector elements, supporting the life extension of these elements. These actions and practices include monitoring of the tritium levels in the primary water, calculating and measuring the fluxes within the beryllium reflector positions, measuring the straightness of the elements to track geometric deformation and visually inspecting the reflector elements for crack formation. Acceptance criteria indicating the end of life of the elements were established. These criteria take into account the smallest gap that could exist between elements, sudden changes in the tritium levels and formation of cracks. All the data obtained through the Beryllium Management Programme are recorded in a database. Additional benefits gained through a Beryllium Management Programme are the availability of a complete irradiation history of the beryllium reflector elements at any point in time and the establishment of a knowledge base to assists in the understanding of the behavior of the beryllium reflector elements in an irradiation environment. Straightness baseline measurements of the new beryllium reflector elements were performed with a beryllium straightness measurement tool, designed at SAFARI-1. The

  18. SAFARI-1 research reactor beryllium reflector element replacement, management and relocation

    Kock, Marisa De; Vlok, Jwh; Steynberg, B.J.

    2012-01-01

    The beryllium (Be) reflector elements of the SAFARI-1 Research Reactor were replaced in October 2011 as part of the Ageing Management Programme of the reactor. After more than three million MWh of operation over a period of 47 years, core reloading became more difficult due to the geometric deformation of the beryllium reflector elements. During the replacement of the reflector elements, criticality and reactivity worth experiments were performed and found to compare favorably with calculated values. A Beryllium Management Programme was established at SAFARI-1 to identify and apply effective and appropriate actions and practices for managing the ageing of the new beryllium reflector elements. This will provide timely detection and mitigation of ageing mechanisms relevant to beryllium reflector elements, supporting the life extension of these elements. These actions and practices include monitoring of the tritium levels in the primary water, calculating and measuring the fluxes within the beryllium reflector positions, measuring the straightness of the elements to track geometric deformation and visually inspecting the reflector elements for crack formation. Acceptance criteria indicating the end of life of the elements were established. These criteria take into account the smallest gap that could exist between elements, sudden changes in the tritium levels and formation of cracks. All the data obtained through the Beryllium Management Programme are recorded in a database. Additional benefits gained through a Beryllium Management Programme are the availability of a complete irradiation history of the beryllium reflector elements at any point in time and the establishment of a knowledge base to assists in the understanding of the behavior of the beryllium reflector elements in an irradiation environment. Straightness baseline measurements of the new beryllium reflector elements were performed with a beryllium straightness measurement tool, designed at SAFARI-1. The

  19. A fundamental research for upgrading heavy oil using syngas as hydrogen source

    Yan, D.; Yuan, M.; Sun, X.; Zhao, S. [China Univ. of Petroleum, Beijing (China). State Key Laboratory of Heavy Oil Processing

    2006-07-01

    The stock of heavy oil and residue from petroleum fractions has become more important as a component in supplying demands for fuel and petrochemical feeds. Finding economical means of upgrading heavy oils is extremely important in order to ensure future fuel supply. A number of new technologies for upgrading heavy oils have been evaluated, including residual fluid catalytic cracking (RFCC), hydrogenation, thermal conversion, and solvent deasphalting. However, the commercial application of such technologies is mainly constrained by the metal and residual carbon concentrations that are present in all heavy oils. Conventional technologies used to upgrade vacuum residue (VR) result in heavy coke formation, with a consequential reduction in the life of expensive, high-performance catalysts. The hydro upgrading process can significantly remove the concentration of heteroatom such as sulfur, nitrogen, and metals in the liquid products. This paper investigated upgrading of heavy oil using syngas as an alternative hydrogen source with a dispersed catalyst. The paper discussed the experiment with reference to the feedstock and catalyst precursors; finely dispersed catalysts preparation; experimental apparatus; experimental design and procedure; and analysis. The results were presented in terms of effects of catalyst dispersion; effect of hydro-upgrading heavy oil using syngas as alternative source; and effects of different catalysts on residue hydrocracking. Last, the paper discussed the properties of the hydrocracked oil treated with syngas. The study confirmed the effectiveness of the slurry bed hydrocracking catalyst using syngas as a hydrogen source. 23 refs., 8 tabs., 16 figs.

  20. Under-Researched Demographics: Heavy Episodic Drinking and Alcohol-Related Problems Among Asian Americans.

    Iwamoto, Derek Kenji; Kaya, Aylin; Grivel, Margaux; Clinton, Lauren

    2016-01-01

    , traditional norms that may directly pertain to hyperfemininzed Asian-American women, including modesty and sexual fidelity, may protect against heavy episodic drinking (Young et al. 2005). Conversely, the risk for heavy episodic drinking may be enhanced in men who strive to demonstrate traditional notions of masculinity through risk-taking and endorsement of playboy norms (Iwamoto et al. 2010). Although this review has illustrated the contemporary state of research on alcohol use among Asian Americans, it also highlights the significant limitations in this literature. Many of the studies reviewed here have used cross-sectional data, which do not allow researchers to infer causality between the various sociocultural factors and problematic alcohol use. One way of addressing this gap in the existing literature may be to implement longitudinal designs to further understand how the temporal relationship between sociocultural factors, including acculturation and gender norms, may impact alcohol use and alcohol-related problem trajectories. There also is a pressing need to develop greater understanding of within-group differences among U.S.-born and foreign-born Asian Americans as well as among as specific ethnic groups. To date, epidemiological research has largely neglected to examine these significant discrepancies. Given the growing prevalence of alcohol use and alcohol-related problems among Asian-American women (Grant et al. 2004; Iwamoto et al. 2010), studies also should focus on this group and explore how the intersection of gender and culture may influence alcohol use. Finally, the majority of research on this population has been conducted in college samples; therefore, it is important to also examine community samples, including U.S.-born young adults who are not attending college and older adult Asian-American populations.

  1. Levels determination of heavy elements (Fe, Cu, Zn, Pb and Hg) in sword fish caught from the bay of Ghazaouet

    Chalabi, A.; Malek, M.; Ghomari, M.; Benamar, M.A.; Tchantchane, A.; Azbouche, A.; Toumert, I.; Benouali, N.; Tobbeche, S. , Algiers; Algeria)

    1993-04-01

    The nuclear technics 'PIXE' and 'XRF', were used for heavy metals analysis (Fe, Cu, Zn, Pb, and Hg), in sword fish (xiphias Gladius) caught in Ghazaouet bay. Muscles, liver and gonads were analysed. The methods gave similar results. A bioaccumulation phenomenon was observed except for Hg. The high amount of concentrations found liver, especially in the case of confirms that liver is a storage organ. The high levels of Zn seem to be due to the industrial wastes from the electrolyte plant in the region. All values were lower than the admissible norms

  2. Control strategies used in the control software for the Heavy Ion Research Facility in Lanzhou

    Zhou, Wen-Xiong [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Postdoctoral Station, Chongqing University, Chongqing 400044 (China); Wang, Yan-Yu [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Pan, Liang-Ming [College of Power Engineering, Chongqing University, Chongqing 400044 (China); Tu, Sheng-Pan [State Grid Chongqing Maintenance Company, Chongqing 400044 (China)

    2016-07-01

    Automation control systems are important for the operation of an accelerator. To ensure the reliable, stable and flexible operation of the Heavy Ion Research Facility in Lanzhou (HIRFL), several control systems are developed. The developed control systems are the SECRAL control system, the LECR3 control system, the LAPECR1 control system and the Electro-Static septum control system. The corresponding control software systems are developed using Visual C++. To ensure the accuracy, stability and flexibility of the control systems, some special control strategies are developed in the control software systems. This paper provides a detailed description of the main control strategies used in the control software systems. The main control strategies are composed of a reliable communication mechanism, a correct data/command transmission mechanism, an efficient data storage mechanism and an interlock protection mechanism. To guarantee a reliable communication between the devices for the commercially purchased devices and the built in-house ones, a modified heartbeat method is developed. To provide flexible reconstitution function for the control systems, the command queue and the state machine are combined. The message mechanism and the multiple windows mechanism are also used for the module mechanism. The relevant control systems are introduced as examples of these control strategies. These systems have been running stably for several years.

  3. Irradiation, annealing, and reirradiation research in the ORNL heavy-section steel irradiation program

    Nanstad, R.K.; Iskander, S.K.; McCabe, D.E.; Sokolov, M.A.

    1997-01-01

    One of the options to mitigate the effects of irradiation on reactor pressure vessels (RPV) is to thermally anneal them to restore the toughness properties that have been degraded by neutron irradiation. This paper summarizes experimental results from work performed as part of the Heavy-Section Steel Irradiation (HSSI) Program managed by Oak Ridge National Laboratory (ORNL) for the U.S. Nuclear Regulatory Commission. The HSSI Program focuses on annealing and re-embrittlement response of materials which are representative of those in commercial RPVs and which are considered to be radiation-sensitive. Experimental studies include (1) the annealing of materials in the existing inventory of previously irradiated materials, (2) reirradiation of previously irradiated/annealed materials in a collaborative program with the University of California, Santa Barbara (UCSB), (3) irradiation/annealing/reirradiation of U.S. and Russian materials in a cooperative program with the Russian Research Center-Kurchatov Institute (RRC-KI), (4) the design and fabrication of an irradiation/anneal/reirradiation capsule and facility for operation at the University of Michigan Ford Reactor, (5) the investigation of potential for irradiation-and/or thermal-induced temper embrittlement in heat-affected zones (HAZs) of RPV steels due to phosphorous segregation at grain boundaries, and (6) investigation of the relationship between Charpy impact toughness and fracture toughness under all conditions of irradiation, annealing, and reirradiation

  4. Control strategies used in the control software for the Heavy Ion Research Facility in Lanzhou

    Zhou, Wen-Xiong; Wang, Yan-Yu; Pan, Liang-Ming; Tu, Sheng-Pan

    2016-01-01

    Automation control systems are important for the operation of an accelerator. To ensure the reliable, stable and flexible operation of the Heavy Ion Research Facility in Lanzhou (HIRFL), several control systems are developed. The developed control systems are the SECRAL control system, the LECR3 control system, the LAPECR1 control system and the Electro-Static septum control system. The corresponding control software systems are developed using Visual C++. To ensure the accuracy, stability and flexibility of the control systems, some special control strategies are developed in the control software systems. This paper provides a detailed description of the main control strategies used in the control software systems. The main control strategies are composed of a reliable communication mechanism, a correct data/command transmission mechanism, an efficient data storage mechanism and an interlock protection mechanism. To guarantee a reliable communication between the devices for the commercially purchased devices and the built in-house ones, a modified heartbeat method is developed. To provide flexible reconstitution function for the control systems, the command queue and the state machine are combined. The message mechanism and the multiple windows mechanism are also used for the module mechanism. The relevant control systems are introduced as examples of these control strategies. These systems have been running stably for several years.

  5. Supplement to the report of the Expert Committee 'Nuclear Physics and Heavy-Ion Research' 1986-1988/89

    1990-02-01

    In the supplement to the scientific report of sponsoring project of the Federal Ministry for Research and Technology 'Nuclear Physics and Heavy-Ion Research' the publications are collected, which have been published in the three years of the sponsoring in the single projects. Essentially only journal articles have been taken up in order to keep the extent of this list surveyable. The taking up of the manifold of dissertations, diploma theses, and talks was generally abandoned. (orig.) [de

  6. Fuel element burnup determination in HEU-LEU mixed TRIGA research reactor core

    Zagar, Tomaz; Ravnik, Matjaz

    2000-01-01

    This paper presents the results of a burnup calculations and burnup measurements for TRIGA FLIP HEU fuel elements and standard TRIGA LEU fuel elements used simultaneously in small TRIGA Mark II research reactor in Ljubljana, Slovenija. The fuel element burnup for approximately 15 years of operation was calculated with two different in house computer codes TRIGAP and TRIGLAV (both codes are available at OECD NEA Data Bank). The calculation is performed in one-dimensional radial geometry in TRIGAP and in two-dimensional (r,φ) geometry in TRIGLAV. Inter-comparison of results shows important influence of in-core water gaps, irradiation channels and mixed rings on burnup calculation accuracy. Burnup of 5 HEU and 27 LEU fuel elements was also measured with reactivity method. Measured and calculated burnup values are inter-compared for these elements (author)

  7. Workshop on environmental research for transuranic elements, Seattle, Washington, November 12--14, 1975

    1975-01-01

    Brief summaries are presented of discussions among scientists conducting research on the transport and diffusion of transuranium elements in aquatic and terrestrial ecosystems. Emphasis was placed on 238 Pu, 239 Pu, 240 Pu, and 241 Am in ecosystems and food chains. Areas for future research were suggested to insure the safe storage of radioactive wastes from the nuclear industry

  8. HELAC-Onia 2.0: an upgraded matrix-element and event generator for heavy quarkonium physics

    Shao, Hua-Sheng

    2016-01-01

    We present an upgraded version (denoted as version 2.0) of the program HELAC-Onia for the automated computation of heavy-quarkonium helicity amplitudes within non-relativistic QCD framework. The new code has been designed to include many new and useful features for practical phenomenological simulations. It is designed for job submissions under cluster enviroment for parallel computations via Python scripts. We have interfaced HELAC-Onia to the parton shower Monte Carlo programs Pythia 8 and QEDPS to take into account the parton-shower effects. Moreover, the decay module guarantees that the program can perform the spin-entangled (cascade-)decay of heavy quarkonium after its generation. We have also implemented a reweighting method to automatically estimate the uncertainties from renormalization and/or factorization scales as well as parton-distribution functions to weighted or unweighted events. A futher update is the possiblity to generate one-dimensional or two-dimensional plots encoded in the analysis file...

  9. HELAC-Onia 2.0: An upgraded matrix-element and event generator for heavy quarkonium physics

    Shao, Hua-Sheng

    2016-01-01

    We present an upgraded version (denoted as version 2.0) of the program HELAC-ONIA for the automated computation of heavy-quarkonium helicity amplitudes within non-relativistic QCD framework. The new code has been designed to include many new and useful features for practical phenomenological simulations. It is designed for job submissions under cluster environment for parallel computations via PYTHON scripts. We have interfaced HELAC-ONIA to the parton shower Monte Carlo programs PYTHIA 8 and QEDPS to take into account the parton-shower effects. Moreover, the decay module guarantees that the program can perform the spin-entangled (cascade-)decay of heavy quarkonium after its generation. We have also implemented a reweighting method to automatically estimate the uncertainties from renormalization and/or factorization scales as well as parton-distribution functions to weighted or unweighted events. A further update is the possibility to generate one-dimensional or two-dimensional plots encoded in the analysis files on the fly. Some dedicated examples are given at the end of the writeup.

  10. Radioactive ion beam production challenges at the Holifield Heavy Ion Research Facility

    Meigs, M.J.; Alton, G.D.; Dowling, D.T.; Haynes, D.L.; Jones, C.M.; Juras, R.C.; Lane, S.N.; Mills, G.D.; Mosko, S.W.; Olsen, D.K.; Tatum, B.A.

    1992-01-01

    The radioactive ion beam (RIB) project at the Holifield Heavy Ion Research Facility (HHIRF) will provide for reconfiguration of the HHIRF accelerator system to enable provision of low-intensity RIBs for nuclear and astrophysics research. As we have progressed with the design of the reconfiguration, we have encountered several challenges that were not immediately obvious when first contemplating the project. The challenges do not seem insurmountable but should keep life interesting for those of us doing the work. A brief review of the project will allow a better understanding of the challenges in RIB production. Radioactive ion beams will be produced with the Isotope Separator On-Line (ISOL) postacceleration technique. In particular, radioactive atoms will be produced by reactions in the thick stopping target of an ISOL-type target-ion source assembly using intense beams from the Oak Ridge Isochronous Cyclotron equipped with a light-ion internal source. This ISOL target-ion source assembly will be mounted on a high-voltage platform with a mass separator. The target ion source will operate at potentials up to 50 kV with respect to the high voltage platform. The radioactive atoms produced by nuclear reactions in the target diffuse to the surface of the heated target material, desorb from this surface, and effuse through a heated transfer tube into an ion source where ionization and extraction take place. Two types of ion sources will be initially considered. A Forced Electron Beam Induced Arc Discharge source, similar to those used by the ISOLDE facility at CERN and by the UNISOR facility at ORNL, will be built to produce positive ions. These positive ions will be focused through an alkali vapor charge-exchange canal to produce negative ions for tandem injection. In addition, a direct negative surface ionization addition or modification to the above source will be built and investigated

  11. Daily tritium intakes by people living near a heavy-water research reactor facility: dosimetric significance

    Trivedi, A.; Cornett, R.J.; Galeriu, D.; Workman, W.; Brown, R.M.

    1997-02-01

    We have estimated the relative daily intakes of tritiated water (HTO) and organically bound tritium (OBT), and have measured HTO-in-urine, in an adult population residing in the town of Deep River, Ontario, near a heavy-water research reactor facility at Chalk River. The daily intake of elevated levels of atmospheric tritium has been estimated from its concentration in environmental and biological samples, and various food items from a local tritium-monitoring program. Where the available data were inadequate, we used estimates generated by an environmental tritium-transfer model. From these data and estimates, we calculated a total daily tritium intake of about 55 Bq. Of this amount, 2.5 Bq is obtained from OBT-in-diet. Inhalation of HTO-in-air (15 Bq d -1 ) and HTO-in-drinking water (15 Bq d -1 ) accounts for more than half of the HTO intake. Skin absorption of HTO from air and bathing or swimming (for 30 min d -1 ) accounts for another 9 Bq d -1 and 0.1 Bq d -1 , respectively. The remaining intake of HTO is from food as tissue-free water tritium. The International Commission on Radiological Protection's recommended two-compartment metabolic model for tritium predicts an equilibrium body burden of about 900 Bq from HTO (818 Bq) and OBT (83 Bq) in the body, which corresponds to an annual tritium dose of 0.41 μSv. The model-predicted urinary excretion of HTO (∼18 Bq L -1 ) agrees well with measured HTO-in-urine (range, 10-32 Bq L -1 ). The OBT dose contribution to the total tritium dose is about 16%. We conclude that for the people living near the Chalk River research reactor facility, the bulk of the tritium dose is due to HTO intake. (author)

  12. Heavy Ion Fusion Accelerator Research (HIFAR) year-end report, April 1, 1985-September 30, 1985

    1985-10-01

    The heavy ion accelerator is profiled. Energy losses, currents, kinetic energy, beam optics, pulse models and mechanical tolerances are included in the discussion. In addition, computational efforts and an energy analyzer are described. 37 refs., 27 figs

  13. Subcritical Noise Analysis Measurements with Fresh and Spent Research Reactor Fuels Elements

    Valentine, T.E.; Mihalczo, J.T.; Kryter, R.C.; Miller, V.C.

    1999-01-01

    The verification of the subcriticality is of utmost importance for the safe transportation and storage of nuclear reactor fuels. Transportation containers and storage facilities are designed such that nuclear fuels remain in a subcritical state. Such designs often involve excess conservatism because of the lack of relevant experimental data to verify the accuracy of Monte Carlo codes used in nuclear criticality safety analyses. A joint experimental research program between Oak Ridge National Laboratory, Westinghouse Safety Management Solutions, Inc., and the University of Missouri was initiated to obtain measured quantities that could be directly related to the subcriticality of simple arrays of Missouri University Research Reactor (MURR) fuel elements. A series of measurement were performed to assess the reactivity of materials such as BORAL, stainless steel, aluminum, and lead that are typically used in the construction of shipping casks. These materials were positioned between the fuel elements. In addition, a limited number of measurements were performed with configurations of fresh and spent (irradiated) fuel elements to ascertain the reactivity of the spent fuel elements. In these experiments, fresh fuel elements were replaced by spent fuel elements such that the subcritical reactivity change could be measured. The results of these measurements were used by Westinghouse Safety Management Solutions to determine the subcriticality of MURR fuel elements isolated by absorbing materials. The measurements were interpreted using the MCNP-DSP Monte Carlo code to obtain the subcritical neutron multiplication factor k(sub eff), and the bias in K(sub eff) that are used in criticality safety analyses

  14. Non-destructive control of cladding thickness of fuel elements for research reactors

    Karlov, Y.; Zhukov, Y.; Chashchin, S

    1997-07-01

    The control method of fuel elements for research reactors by means of measuring beta particles back scattering made it possible to perform complete automatic non-destructive control of internal and external claddings at our plant. This control gives high guarantees of the fuel element correspondence to the requirements. The method can be used to control the three-layer items of different geometry, including plates. (author)

  15. Results of fuel elements fabrication on the basis of increased concentration dioxide fuel for research reactors

    Alexandrov, A.B.; Afanasiev, V.L.; Enin, A.A.; Suprun, V.B.

    1996-01-01

    According to the Russian Reduced Enrichment for Research and Test Reactors (RERTR) program, that were constructed under the Russian projects, at the Novosibirsk Chemical Concentrates Plant the pilot series of different configuration (WR-M2, MR, IRT-4M) fuel elements, based on increased concentration uranium dioxide fuel, have been fabricated for reactor tests. Comprehensive fabricated fuel elements quality estimation has been carried out. (author)

  16. [Research Progress and Prospect of Applications of Finite Element Method in Lumbar Spine Biomechanics].

    Zhang, Zhenjun; Li, Yang; Liao, Zhenhua; Liu, Weiqiang

    2016-12-01

    Based on the application of finite element analysis in spine biomechanics,the research progress of finite element method applied in lumbar spine mechanics is reviewed and the prospect is forecasted.The related works,including lumbar ontology modeling,clinical application research,and occupational injury and protection,are summarized.The main research areas of finite element method are as follows:new accurate modeling process,the optimized simulation method,diversified clinical effect evaluation,and the clinical application of artificial lumbar disc.According to the recent research progress,the application prospects of finite element method,such as automation and individuation of modeling process,evaluation and analysis of new operation methods and simulation of mechanical damage and dynamic response,are discussed.The purpose of this paper is to provide the theoretical reference and practical guidance for the clinical lumbar problems by reviewing the application of finite element method in the field of the lumbar spine biomechanics.

  17. WHO/IAEA joint research programme on trace elements in cardiovascular diseases

    1980-03-01

    After several years of support by WHO and IAEA for the joint research programme on trace elements in cardiovascular diseases, a consultants' meeting was held (1) to examine the present status of the programme with a view to advising on actions necessary for its completion, and (2) to advise on the form, content and timing of a final report. The meeting was attended by the invited experts and other persons. The main work of this research programme is divided, as before, between two projects, (1) on Cd, Cr, Cu, Se, Zn and other elements in relation to ischaemic heart disease, and (2) on Cd, Se and Zn in relation to arterial hypertension

  18. Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

    Noli, Fotini, E-mail: noli@chem.auth.gr; Tsamos, Panagiotis, E-mail: pktsamos@chem.auth.gr

    2016-09-01

    The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

  19. Concentration of heavy metals and trace elements in soils, waters and vegetables and assessment of health risk in the vicinity of a lignite-fired power plant

    Noli, Fotini; Tsamos, Panagiotis

    2016-01-01

    The pollution of agricultural soils, waters and products in the regions of lignite mines and fired power plants is of great importance. The concentration of As, Βa, Co, Cr, Sr, Sc, Th, U, Zn in soils and waters in the vicinity of a lignite-fired power plant in Northern Greece was determined using Instrumental Neutron Activation Analysis. The determination frequency was every three months during a period of one year in order to evaluate the seasonal impact of the pollution to the environment. Measurements were performed in three locations around the lignite mine as well as in one reference location at a certain distance from the mine. The results, which exhibited a slight seasonal variation, were compared, where possible, with literature values from other countries. The obtained data in most of the cases did not exceed the normal levels and indicated that the investigated area was only slightly contaminated. The concentration of heavy and trace metals was also measured in three common garden crops (tomato, cucumber and parsley) grown in this area. The calculated transfer factors (TF) from soil to vegetables and health risk quotients (HQ) do not denote a health risk. - Highlights: • Seasonal variation of heavy metals concentrations in soils and waters in a lignite mining area. • The elevated concentrations detected by NAA indicating minor contamination of the studied area. • Determination of minor and trace elements in vegetables. • The transfer factors and health risk quotients indicating a possible slight contamination in the area.

  20. Levels of rare earth elements, heavy metals and uranium in a population living in Baiyun Obo, Inner Mongolia, China: a pilot study.

    Hao, Zhe; Li, Yonghua; Li, Hairong; Wei, Binggan; Liao, Xiaoyong; Liang, Tao; Yu, Jiangping

    2015-06-01

    The Baiyun Obo deposit is the world's largest rare earth elements (REE) deposit. We aimed to investigate levels of REE, heavy metals (HMs) and uranium (U) based on morning urine samples in a population in Baiyun Obo and to assess the possible influence of rare earth mining processes on human exposure. In the mining area, elevated levels were found for the sum of the concentrations of light REE (LREE) and heavy REE (HREE) with mean values at 3.453 and 1.151 μg g(-1) creatinine, which were significantly higher than those in the control area. Concentrations of HMs and U in the population increased concomitantly with increasing REE levels. The results revealed that besides REE, HMs and U were produced with REE exploitation. Gender, age, educational level, alcohol and smoking habit were major factors contributing to inter-individual variation. Males were more exposed to these metals than females. Concentrations in people in the senior age group and those with only primary education were low. Drinking and smoking were associated with the levels of LREE, Cr, Cu, Cd and Pb in morning urine. Hence this study provides basic and useful information when addressing public and environmental health challenges in the areas where REE are mined and processed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Elaboration of y-fanjasite catalysts containing radioactive elements such as uranyl ion in order to obtain aromatic solvents and heavy amines

    Nibou, D.

    1990-06-01

    The present work has shown the possibility of ammonia alkylation by n-octanol-l in gaseous phase, in presence of zeolitic catalysts. These catalysts are Y faujasitic types being used in waste water demineralization containing radioactive elements such as uranyl ion. This ion gives to the Y faujasite similar activity and selectivity as those of catalysts containing rare earths or transition metals. Toluene disproportionation has permitted to test beforehand catalysts destined to ammonia alkylation and to compare their mechanism. We have also proved the possibility to produce heavy amines such as tertiary amines which are used as uranium extractant agent. Some zeolites such as ZSM-5, beta, X, A, analcime, HS and Y faujasite type are prepared by hydrothermal synthesis method and characterized by some analysis techniques

  2. The Research on the Width of the Closed-Circuit Square-shaped Embroidery Element

    Žaneta JUCHNEVIČIENĖ

    2017-08-01

    Full Text Available In modern manufacturing embroidered elements are used in such areas as implant production, rehabilitation (e.g., embroidered sensors, medical diagnostics, production of smart garments etc., where high accuracy is required to maintain the functionality of the product. Due to the influence of mechanical forces taking part in the embroidery process, the embroidery system is deformed, resulting in noncompliance of the embroidery element with the digitally designed one. Three fabrics have been selected as the objects of the research with the fiber composition of 65 % polyester and 35 % cotton, differing by weave and density. 60 × 60 mm and 6 mm wide closed circuit square-shaped embroidery elements have been used for the research. According to the performed analysis of the results, the dimensions of the closed-circuit square-shaped embroidery element have changed in comparison to that of the digitally designed one. The width of the embroidery element, which was the most adequate to the digitally designed one, was achieved in the direction of warp. The obtained results have shown that in the corners the width of the embroidery element in the directions of warp and weft is bigger than the one in the centers of the segments.DOI: http://dx.doi.org/10.5755/j01.ms.23.2.16095

  3. Concentration levels and temporal variations of heavy elements in the urban particulate matter of Navi Mumbai, India

    Kothai, P.; Saradhi, I.V.; Prathibha, P.; Pandit, G.G.; Puranik, V.D.

    2012-01-01

    Coarse and fine fractions of particulate matter (PM) were collected and analysed for trace elements using Instrumental Neutron Activation Analysis and Energy Dispersive X-ray Fluorescence techniques. The result showed high concentrations of Fe, S, Zn and Pb in both the size fractions. The elemental data obtained is used to analyze the temporal and seasonal variations. The trend showed maximum concentrations of PM and metals during winter and minimum during the monsoon season. Enrichment Factor (EF) and source analysis was performed for the same data set to identify the strength of contribution of anthropogenic sources and the possible contributing sources in the study area. EF studies showed high enrichments of Zn, Pb and As in the fine fraction particles. Crustal, vehicular and industrial emissions are identified as the major contributing sources of PM in the study area. (author)

  4. Heavy ion radiation biology research facility and ongoing activities at the Inter-University Accelerator Centre, New Delhi

    Sarma, Asitikantha

    2014-01-01

    Heavy Ion Radiation Biology is an interdisciplinary science involving use of charged particle accelerator in the study of molecular biology. It is the study of the interaction of a beam of swift heavy ions with a biological system. In contrast to the sparsely ionizing photon or electron radiation, the high velocity charged heavy ions leave a track of densely populated ionization sites resulting in clustered DNA damage. The growing interest in this field encompasses the studies in gene expression, mechanisms of cell death, DNA damage and repair, signal transduction etc. induced because of this unique assault on the genetic material. IUAC radiation biology programme is focused on the in-vitro studies of different effects of heavy ion irradiation on eukaryotic cells. The facility provides a laboratory for pre and post irradiation treatment of samples. The irradiation system called ASPIRE (Automatic Sample Positioning for Irradiation in Radiation Biology Experiments) is installed at the dedicated Radiation Biology Beam line. It produces a nearly uniform flux distribution over a irradiation field of 40 mm diameter. The particle doses can be preselected and repeated within inherent statistical accuracy. The particle energy can also be measured. The facility is at present utilized by the University researchers of India. A few results obtained by the investigators would be presented. The outcome of the research in heavy ion radiation biology would be of immense use in augmenting the efficacy of Hadron therapy of cancer. The results would also contribute to the field of space radiation protection. It would also help in understanding the phenomena subsequent to complex DNA damage. (author)

  5. Heavy-element yields and abundances of asymptotic giant branch models with a Small Magellanic Cloud metallicity

    Karakas, Amanda I.; Lugaro, Maria; Carlos, Marília; Cseh, Borbála; Kamath, Devika; García-Hernández, D. A.

    2018-06-01

    We present new theoretical stellar yields and surface abundances for asymptotic giant branch (AGB) models with a metallicity appropriate for stars in the Small Magellanic Cloud (SMC, Z = 0.0028, [Fe/H] ≈ -0.7). New evolutionary sequences and post-processing nucleosynthesis results are presented for initial masses between 1 and 7 M⊙, where the 7 M⊙ is a super-AGB star with an O-Ne core. Models above 1.15 M⊙ become carbon rich during the AGB, and hot bottom burning begins in models M ≥ 3.75 M⊙. We present stellar surface abundances as a function of thermal pulse number for elements between C to Bi and for a selection of isotopic ratios for elements up to Fe and Ni (e.g. 12C/13C), which can be compared to observations. The integrated stellar yields are presented for each model in the grid for hydrogen, helium, and all stable elements from C to Bi. We present evolutionary sequences of intermediate-mass models between 4 and 7 M⊙ and nucleosynthesis results for three masses (M = 3.75, 5, and 7 M⊙) including s-process elements for two widely used AGB mass-loss prescriptions. We discuss our new models in the context of evolved AGB and post-AGB stars in the SMCs, barium stars in our Galaxy, the composition of Galactic globular clusters including Mg isotopes with a similar metallicity to our models, and to pre-solar grains which may have an origin in metal-poor AGB stars.

  6. KEPLER-15b: A HOT JUPITER ENRICHED IN HEAVY ELEMENTS AND THE FIRST KEPLER MISSION PLANET CONFIRMED WITH THE HOBBY-EBERLY TELESCOPE

    Endl, Michael; MacQueen, Phillip J.; Cochran, William D.; Brugamyer, Erik J.; Buchhave, Lars A.; Rowe, Jason; Lucas, Phillip; Isaacson, Howard; Bryson, Steve; Howell, Steve B.; Borucki, William J.; Caldwell, Douglas; Christiansen, Jessie L.; Haas, Michael R.; Fortney, Jonathan J.; Hansen, Terese; Ciardi, David R.; Demory, Brice-Olivier; Everett, Mark; Ford, Eric B.

    2011-01-01

    We report the discovery of Kepler-15b (KOI-128), a new transiting exoplanet detected by NASA's Kepler mission. The transit signal with a period of 4.94 days was detected in the quarter 1 (Q1) Kepler photometry. For the first time, we have used the High Resolution Spectrograph (HRS) at the Hobby-Eberly Telescope (HET) to determine the mass of a Kepler planet via precise radial velocity (RV) measurements. The 24 HET/HRS RVs and 6 additional measurements from the Fibre-fed Échelle Spectrograph spectrograph at the Nordic Optical Telescope reveal a Doppler signal with the same period and phase as the transit ephemeris. We used one HET/HRS spectrum of Kepler-15 taken without the iodine cell to determine accurate stellar parameters. The host star is a metal-rich ([Fe/H] = 0.36 ± 0.07) G-type main-sequence star with T eff = 5515 ± 124 K. The semi-amplitude K of the RV orbit is 78.7 +8.5 –9.5 m s –1 , which yields a planet mass of 0.66 ± 0.1 M Jup . The planet has a radius of 0.96 ± 0.06 R Jup and a mean bulk density of 0.9 ± 0.2 g cm –3 . The radius of Kepler-15b is smaller than the majority of transiting planets with similar mass and irradiation level. This suggests that the planet is more enriched in heavy elements than most other transiting giant planets. For Kepler-15b we estimate a heavy element mass of 30-40 M ⊕ .

  7. Hydraulic and hydrodynamic tests for design evaluation of research reactors fuel elements

    Kulichevsky, R.; Martin Ghiselli, A.; Fiori, J.; Yedros, P.

    2002-01-01

    During the design steps of research reactors fuel elements some tests are usually necessary to verify its design, i.e.: its hydraulic characteristics, dynamical response and structural integrity. The hydraulic tests are developed in order to know the pressure drops characteristics of different parts or elements of the prototype and of the whole fuel element. Also, some tests are carried out to obtain the velocity distribution of the coolant water across different prototype's sections. The hydrodynamic tests scopes are the assessment of the dynamical characteristics of the fuel elements and their components and its dynamical response considering the forces generated by the coolant flowing water at different flow rate conditions. Endurance tests are also necessary to qualify the structural design of the FE prototypes and their corresponding clamp tools, verifying the whole system structural integrity and wear processes influences. To carry out these tests a special test facility is needed to obtain a proper representation of the hydraulic and geometric boundary conditions of the fuel element. In some cases changes on the fuel element prototype or dummy are necessary to assure that the data results are representative of the case under study. Different kind of sensors are mounted on the test section and also on the fuel element itself when necessary. Some examples of the instrumentation used are strain gauges, displacement transducers, absolute and differential pressure transducers, pitot tubes, etc. The obtained data are, for example, plates' vibration amplitudes and frequencies, whole bundle displacement characterization, pressure drops and flow velocity measurements. The Experimental Low Pressure Loop is a hydraulic loop located at CNEA's Constituyentes Atomic Center and is the test facility where different kind of tests are performed in order to support and evaluate the design of research reactor fuel elements. A brief description of the facility, and examples of

  8. Relativistic effects in bonding and dipole moments for the diatomic hydrides of the sixth-row heavy elements

    Ramos, A.F.; Pyper, N.C.; Malli, G.L.

    1988-01-01

    Ab initio Dirac-Fock (DF) and nonrelativistic-limit (NRL) wave functions and dipole moments are calculated to investigate the bonding characteristics and the relativistic effects in the systems HgH + , TlH, PbH + , and BiH. The dipole moment of AuH is evaluated using the DF self-consistent field and relativistic configuration-interaction wave functions obtained by G. L. Malli and N. C. Pyper [Proc. R. Soc. London, Ser. A 407, 377 (1986)]. Contour plots of relativistic molecular orbital densities and difference density maps are presented to illustrate the arrangement of electronic charge in these systems. It is found that the 5d orbitals are involved in the bonding of HgH + , whereas they do not play a significant role in TlH and PbH + . The relativistic calculations predict HgH + , TlH, and PbH + to be bound. The nonrelativistic-limit wave functions predict HgH + and BiH to be unbound but TlH and PbH + to be bound. It is also found that the calculated dipole moments using the DF and the NRL wave functions for these heavy systems differ significantly in magnitude, and in some cases even in the sign

  9. Heavy Ion Fusion Accelerator Research (HIFAR) year-end report, April 1, 1989--September 30, 1989

    1989-12-01

    This report contains the following topics on heavy ion fusion: MBE-4 drifting beam quadrupole operating range; transverse emittance growth in MBE-4; an improved ion source for MBE-4; drifting beam studies on MBE-4; 2-MV injector; improvements in lifetime of the C + source; injector control system; Maxwell spark gap test update; ILSE cosine 2θ quadrupole magnet development; electrostatic quadrupole prototype development activity; induction accelerator cell development; effect of a spread in beamlet currents on longitudinal stability; and heavy ion linac driver analysis

  10. Economical analysis to utilize MTR fuel elements using silicides in research reactors

    Bergallo, Juan E.; Novara, Oscar E.; Adelfang, Pablo

    2000-01-01

    According to international programs on reducing enrichment in research reactors and the necessity to maintain their operation, new fuel elements have been developed in order to meet both objectives. Thus, U-Si alloy fuel elements for research reactors are becoming of greater interest for the international markets. It became necessary to make an economic study about the convenience of introducing this type of fuel elements in the RA-3 reactor and to know the potentiality of this fuel. The economical behavior of the reactor operation has been evaluated comparing the actual U 3 O 8 nuclear fuel cycle with U 3 Si 2 nuclear fuels. Results obtained show that the main economical factor to determine the change of fuels is the cost of fabrication, and the change is advisable up to an 80% difference. The other factors related to the cost of nuclear fuel cycle are not relevant or have real minor impacts. (author)

  11. Evaluation of the effect of heavy rare earth elements on the microstructure and mechanical and electrical properties of zirconia - Yttria ceramics

    Lazar, Dolores Ribeiro Ricci

    2002-01-01

    The use of Yttria concentrates for synthesis and processing of zirconia based ceramics, applied as structural and solid electrolyte materials, was investigated in this work. Terbium, dysprosium, holmium, erbium and ytterbium are chemical elements, classified as heavy rare earths, that can be found in those concentrates due to their association with yttrium ores. The ceramic characteristics were compared to zirconia - Yttria and zirconia - Yttria - rare earth oxide systems. The dopant content was 3 and 9 mol%. The raw materials were prepared by the coprecipitation route using solutions from the chemical processing of zircon and monazite ores and obtained by dissolution of high purity rare earth oxides. In the first part of this work, calcination, milling and ceramic processing were studied to produce ceramics with densities up to 95% TD. Samples were prepared in optimized conditions for the evaluation of the effect of each heavy rare earth element. Powders were characterized by chemical analysis. X-ray diffraction, scanning and transmission electron microscopy, gas adsorption (BET) and laser diffraction for the determination of the agglomerate size distributions. Green pellets were characterized by mercury porosimetry and the sintering kinetic was studied by dilatometry. The characterization of the as-sintered pellets was performed by the apparent density measurement (Archimedes method). X-ray diffraction, microstructure analysis by scanning and transmission electron microscopy, Vickers indentation tests for hardness and fracture toughness determination, dynamic mechanical analysis for the elastic modulus measurement, and impedance spectroscopy for electrical resistivity measurement. It was observed that the presence of heavy rare earths in a concentrate containing 85 wt% of Yttria has no significant influence on the properties of zirconia based ceramics. TZP ceramics, containing 3 mol% of dopants, have grain size smaller than 0.4μm, and Vickers hardness and

  12. Annual report of joint research for using heavy ion accelerator for cancer therapy of the fiscal year 1996

    NONE

    1997-04-01

    The heavy ion project consisted of 2 parts; clinical studies using HIMAC and joint basic researches using it. The clinical studies have been satisfactorily progressed and the number of patients treated by HIMAC reached 230 in total by the end of the fiscal year 1996. In Japan, HIMAC is the only apparatus for heavy ion acceleration. Thus, a lot of concerns from not only the medical and biological fields, but also other fundamental fields are paid to HIMAC. Further, the beam of HIMAC has been attracting international concerns, especially in the fields such as simulation of cosmic environment by heavy ion beam, dose determination using the beam, international comparison of its biological effects, etc. The operating times of HIMAC in 1996 was ca. 4800 hours in total and of those ca. 2700 hours were used for joint researches. This annual report include 12 reports of clinical research group, 4 of diagnosis one 64 of biology one and 42 of physical and engineering one. (M.N.)

  13. Determination of Heavy elements in Drinking Water from Different Regions of Baghdad City (Iraq Using EDXRF Spectrometer

    Muhanad H. Alrakabi

    2017-11-01

    Full Text Available It was calculated the average concentrations of elements manganese, iron, cobalt, nickel, copper, zinc, arsenic, cadmium and lead in the sixteen samples of drinking water (tap water, were collected from different areas in the Baghdad city. The Results indicated that the average of concentrations of the elements Mn, Fe, Pb, Ni and Cd (0.44ppm, 0.49ppm, 0.04ppm, 0.17ppm and 1.2ppm respectively higher than permissible limit while the concentrations of elements Cu and Zn (0.11ppm and 0.14ppm respectively were lower than the permissible limit of World Health Organization (WHO standards (1ppm and 3ppm respectively for drinking water and the concentration of Arsenic in the nuclear lab sample in college of sciences - Mustansiriyah University was higher than permissible limit. All the drinking water samples were analyzed and determined the physical and chemical properties such as Electrical Conductivity (EC, pH, and Total Dissolved Solids (TDS. The highest value was (1064μS/cm in Al-Tuwaitha sample and the lowest value (531μS/cm in Al-Sadr City (Sector 7 sample for the Electrical Conductivity. The pH values ranged from (7.0-8.2. The average levels of Total Dissolved Solids (TDS, the highest value was 550 mg/L in the Diyala Bridge sample while the lowest value 276mg/L in Al-Sadr City (Sector 7 sample. The results were compared with national and international standards, and it’s also showed that the values of the parameters within the permissible limit of World Health Organization (WHO standards, except the Electrical Conductivity values for some samples were higher than permissible limit. According to these results, all the water projects must be monitored as well as using the proper and modern techniques for treatment the drinking water.

  14. Determination of heavy metals and other elements by Neutron Activation Analysis in sediment cores of laguna Mar Chiquita (Cordoba, Argentina)

    Larizzatti, Flavio Eduardo

    2001-01-01

    Laguna Mar Chiquita is one of the largest water bodies of South America. It is a big lake of saline waters, and its geographic localization is SOMS' S, 62 deg 30' W, about 150 km Northwest of Cordoba, Argentina. Due to its large variability of hydrological budget, surface and water levels produced periods of low stands (LLP) and high stands (HLP). This fluctuation of water level also produces substantial changes in the water salinity. The principal tributary of the Laguna Mar Chiquita is Dulce River and also receives water from two other rivers: Suquia and Xanaes. The Suquia River drains in a small satellite lake, the Laguna del Plata. The purpose of the present work was to investigate the sediment composition of the Laguna Mar Chiquita (2 sediment cores) and del Plata (one sediment core) by using Neutron Activation Analysis (NAA) technique. The three 60 cm long sediment cores, sliced each 2 cm, were analyzed and 26 elements were determined (As, Ba, Br, Ce, Co, Cr, Cs, Eu, Fe, Hf, La, Lu, Na, Nd, Rb, Sb, Sc, Se, Sm, Ta, Tb, Th, U, Yb, Zn e Zr). Other complementary techniques were utilized: macro elements (Al, Ca, Fe, K, Mg, Mn, Na, P, Si, Ti) were determined by X-ray fluorescence, and the mineralogical composition of the sediments was determined by X-ray diffraction. The results obtained did not show any indication of anthropic contribution in the sediment composition, and concentration of the majority of the elements analyzed is uniform along the entire profile of the analyzed core. Statistical analysis of elemental concentrations (Cluster Analysis) reflects that in Laguna del Plata the fine fractions of the sediments is dominated by detrital minerals, while in the Laguna Mar Chiquita, the neo formed minerals are the principal components. In both lakes, it was possible to identify compositional variations in the sediment segments, which may correspond to temporal fluctuations in the sedimentation conditions. The statistical analysis associated to sedimentation

  15. Achievement report for fiscal 1997 on research under New Sunshine Program. Research on heavy oil hydrogenation and heavy oil/coal coprocessing; 1997 nendo jushitsuyu no suisoka shori narabi ni jushitsuyu/sekitan no coprocessing ni kansuru kenkyu seika hokokusho

    NONE

    1998-02-01

    The achievements of the Hokkaido National Industrial Research Institute relating to the titled research are reported. In the study relating to the structural properties of heavy oils, the structures of products of Green River shale oil carbonization is analyzed, heterofunctional groups contained in the oil are subjected to FT-IR (Fourier transform infrared) spectroscopic analysis, and their forms of existence are investigated. In the study relating to the hydrogenation process of heavy oils, findings obtained from experiments are reported, which involve the processing of shale oil by hydrogenation and changes brought about in its chemical structure, hydrogenation of oil sand bitumen, kinetics of hydrocracking of bitumen at a high conversion rate, and a lumping model for bitumen hydrocracking reaction. In the study relating to the coprocessing of heavy oil/coal, coprocessing is experimented for coal and shale oil, coal and oil sand bitumen, and other combinations, and the results are reported. Also, a review is made of the transfer of hydrogen in coprocessing. (NEDO)

  16. Criticality calculation of the deposits for the fuel elements in RP-10 nuclear research reactor

    Aguirre, Alvaro; Bruna, Ruben

    2013-01-01

    This paper shows the results of the criticality calculation of the deposits for irradiated and non-irradiated fuel elements in the RP-10 research reactor with MCNP5 code. In all cases and for normal and incidental conditions, the effective multiplication factor (K eff ) results less than 0,90 according to the acceptance criterion. (authors).

  17. Stakeholder Perceptions of the Need for Research on Elements of Service Dog Partnerships in the Workplace

    Glenn, Margaret K.

    2015-01-01

    Purpose: To examine the perceived need for research on elements of successful service dog partnerships in the workplace outlined by stakeholders in an exploratory study. Method: A structured mixed methods approach was used to gather ideas from people with service dogs, trainers, vocational rehabilitation counselors, and other health care…

  18. Giant magnetic anisotropy of heavy p-elements on high-symmetry substrates: a new paradigm for supported nanostructures

    Pang, Rui; Deng, Bei; Shi, Xingqiang; Zheng, Xiaohong

    2018-04-01

    Nanostructures with giant magnetic anisotropy energies (MAEs) are desired in designing miniaturized magnetic storage and quantum computing devices. Previous works focused mainly on materials or elements with d electrons. Here, by taking Bi–X(X = In, Tl, Ge, Sn, Pb) adsorbed on nitrogenized divacancy of graphene and Bi atoms adsorbed on MgO(100) as examples, through ab initio and model calculations, we propose that special p-element dimers and single-adatoms on symmetry-matched substrates possess giant atomic MAEs of 72–200 meV, and has room temperature structural stability. The huge MAEs originate from the p-orbital degeneracy around the Fermi level in a symmetry-matched surface ligand field and the lifting of this degeneracy when spin–orbit interaction (SOI) is taken into account. Especially, we developed a simplified quantum mechanical model for the design principles of giant MAEs of supported magnetic adatoms and dimers. Thus, our discoveries and mechanisms provide a new paradigm to design giant atomic MAE of p electrons in supported nanostructures.

  19. Biological and medical research with accelerated heavy ions at the Bevalac, 1977-1980

    Pirruccello, M.C.; Tobias, C.A.

    1980-11-01

    Separate abstracts were prepared for the 46 papers presented in this progress report. This report is a major review of studies with accelerated heavy ions carried out by the Biology and Medicine Division of Lawrence Berkeley Laboratory from 1977 to 1980

  20. RESEARCH OF HEAVY METALS, ORGANOCHLORINE AND ORGANOPHOSPHORUS PESTICIDES IN POWDERED INFANT FORMULA

    M.C. Abete

    2009-02-01

    Full Text Available During the period between october 2007 and november 2008 were collected 60 samples of powdered infant formula. The analysis for the detection of heavy metals, organochlorine and organophosphorus pesticides show that the environmental situation is under control and powdered infant formula satisfies this health requisite.

  1. Biological and medical research with accelerated heavy ions at the Bevalac, 1977-1980. [Lead abstract

    Pirruccello, M.C.; Tobias, C.A. (eds.)

    1980-11-01

    Separate abstracts were prepared for the 46 papers presented in this progress report. This report is a major review of studies with accelerated heavy ions carried out by the Biology and Medicine Division of Lawrence Berkeley Laboratory from 1977 to 1980. (KRM)

  2. Irradiation tests on PHWR type fuel elements in TRIGA research reactor of INR Pitesti

    Horhoianu, Grigore [Institute for Nuclear Research, Pitesti (Romania). Nuclear Fuel Engineering Lab.; Sorescu, Ion [Institute for Nuclear Research, Pitesti (Romania). TRIGA Reactor Loop Facility; Parvan, Marcel [Institute for Nuclear Research, Pitesti (Romania). Hot Cells Lab.

    2012-12-15

    Nine PHWR type fuel elements with reduced length were irradiated in loop A of the TRIGA Research Reactor of INR Pitesti. The primary objective of the test was to determine the performance of nuclear fuel fabricated at INR Pitesti at high linear powers in pressurized water conditions. Six fuel elements were irradiated with a ramp power history, achieving a maximum power of 45 kW/m during pre-ramp and of 64 kW/m in the ramp. The maximum discharge burnup was of 216 MWh/kgU. Another three fuel elements with reduced length were irradiated with declining power history. At the beginning of irradiation the fuel elements achieved a maximum linear power of 66 kW/m. The maximum fuel power was about 1.3 times the maximum expected in PHWR. The maximum discharge burnup was 205 MWh/kgU. The elements were destructively examined in the hot cells of INR Pitesti. Temperature-sensitive parameters such as UO{sub 2} grain growth, fission-gas release and sheath deformations were examined. The tests proved the feasibility of irradiating PHWR type fuel elements at linear powers up to 66 kW/m under pressurized water conditions and demonstrated the possibility of more flexible operation of this fuel in power reactors. This paper presents the results of the investigation. (orig.)

  3. [Spectroscopic Research on Slag Nanocrystal Glass Ceramics Containing Rare Earth Elements].

    Ouyang, Shun-li; Li, Bao-wei; Zhang, Xue-feng; Jia, Xiao-lin; Zhao, Ming; Deng, Lei-bo

    2015-08-01

    The research group prepared the high-performance slag nanocrystal glass ceramics by utilizing the valuable elements of the wastes in the Chinese Bayan Obo which are characterized by their symbiotic or associated existence. In this paper, inductively coupled plasma emission spectroscopy (ICP), X-ray diffraction (XRD), Raman spectroscopy (Raman) and scanning electron microscopy (SEM) are all used in the depth analysis for the composition and structure of the samples. The experiment results of ICP, XRD and SEM showed that the principal crystalline phase of the slag nanocrystal glass ceramics containing rare earth elements is diopside, its grain size ranges from 45 to 100 nm, the elements showed in the SEM scan are basically in consistent with the component analysis of ICP. Raman analysis indicated that its amorphous phase is a three-dimensional network structure composed by the structural unit of silicon-oxy tetrahedron with different non-bridging oxygen bonds. According to the further analysis, we found that the rare earth microelement has significant effect on the network structure. Compared the nanocrystal slag glass ceramic with the glass ceramics of similar ingredients, we found that generally, the Raman band wavenumber for the former is lower than the later. The composition difference between the glass ceramics and the slag nanocrystal with the similar ingredients mainly lies on the rare earth elements and other trace elements. Therefore, we think that the rare earth elements and other trace elements remains in the slag nanocrystal glass ceramics have a significant effect on the network structure of amorphous phase. The research method of this study provides an approach for the relationship among the composition, structure and performance of the glass ceramics.

  4. Study the chemical composition and biological outcomes resulting from the interaction of the hormone adrenaline with heavy elements: Infrared, Raman, electronic, 1H NMR, XRD and SEM studies

    Ibrahim, Omar B.; Mohamed, Mahmoud A.; Refat, Moamen S.

    2014-01-01

    Heavy metal adrenaline complexes formed from the reaction of adrenaline with Al3+, Zn2+, Sn2+, Sb3+, Pb2+and Bi3+ ions in methanolic solvent at 60 °C. The final reaction products have been isolated and characterization using elemental analyses (% of carbon, hydrogen and nitrogen), conductivity measurements, mid infrared, Raman laser, UV-Vis, 1H NMR spectra, X-ray powder diffraction, scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDX). Upon the spectroscopic, conductivity and elemental analyses, the stoichiometric reactions indicated that the data obtained refer to 1:2 (M:L) for Zn2+, Sn2+, Pb2+and Bi3+ complexes [Zn(Adr)2(Cl)2], [Sn(Adr)2]Cl2, [Pb(Adr)2](NO3)2 and [Bi(Adr)2(Cl)2]Cl, while the molar ratio 1:3 (M:L) for Al3+ and Sb3+ with formulas [Al(Adr)3](NO3)3 and [Sb(Adr)3]Cl3. The infrared and Raman laser spectra interpreted the mode of interactions which associated through the two phenolic groups of catechol moiety. The adrenaline chelates have been screened for their in vitro antibacterial activity against four bacteria, Gram-positive (Bacillus subtilis and Staphylococcus aureus) and Gram-negative (Escherichia coli and Pseudomonas aeruginosa) and two strains of fungus (Aspergillus flavus and Candida albicans). The metal chelates were shown to possess more antibacterial and antifungal activities than the free adrenaline chelate.

  5. Online tutoring procedure for research project supervision: management, organization and key elements

    Antònia Darder Mesquida

    2015-07-01

    Full Text Available Research project tutoring appears as a crucial element for teaching; it is a planned action based on the relationship between a tutor and a student. This paper presents the findings of a design and development research which has as its main aim to create an organization system for the tutoring of online research projects. That system seeks to facilitate the tutoring and supervision task with trainee researchers, providing guidance for its management and instruments for its implementation. The main conclusions arising from this research derive from considering the need to offer a solution to the problem of distance research project supervision and has materialized in organization and sequencing through a model about the variables that influence the research project tutoring problem.

  6. Identification and Characterization of Putative Integron-Like Elements of the Heavy-Metal-Hypertolerant Strains of Pseudomonas spp.

    Ciok, Anna; Adamczuk, Marcin; Bartosik, Dariusz; Dziewit, Lukasz

    2016-11-28

    Pseudomonas strains isolated from the heavily contaminated Lubin copper mine and Zelazny Most post-flotation waste reservoir in Poland were screened for the presence of integrons. This analysis revealed that two strains carried homologous DNA regions composed of a gene encoding a DNA_BRE_C domain-containing tyrosine recombinase (with no significant sequence similarity to other integrases of integrons) plus a three-component array of putative integron gene cassettes. The predicted gene cassettes encode three putative polypeptides with homology to (i) transmembrane proteins, (ii) GCN5 family acetyltransferases, and (iii) hypothetical proteins of unknown function (homologous proteins are encoded by the gene cassettes of several class 1 integrons). Comparative sequence analyses identified three structural variants of these novel integron-like elements within the sequenced bacterial genomes. Analysis of their distribution revealed that they are found exclusively in strains of the genus Pseudomonas .

  7. The Multitracer technique: manufacturing and application to bio-trace elemental research

    Enomoto, Shuichi; Hirunuma, Rieko

    2002-01-01

    A versatile radioactive multitracer technique has been developed at RIKEN Accelerator Research Facility about 11 years before. It enables efficient and simultaneous tracing of a number of elements under identical experimental conditions. Since 1991, the multitracer technique has been applied for an investigation of a behavior of various elements in chemistry, biochemistry, pharmaceutical sciences, medical sciences, nutritional sciences, agricultural sciences, and environmental sciences. Now, the multitracer has been used in more than 50 laboratories in the world. Its principle and features are presented with examples of recent application. (author)

  8. Burnup measurements on spent fuel elements of the RP-10 research reactor

    Vela Mora, Mariano; Gallardo Padilla, Alberto; Palomino, Jose Luis Castro

    2011-01-01

    This work describes the measurement, using nondestructive gamma-ray spectroscopy, of the average burnup attained by Material Testing Reactor (MTR) fuel elements irradiated in the RP-10 research reactor. Measurements were performed at the reactor storage pool area using 137 Cs as the only burnup monitor, even for spent fuel elements with cooling times much shorter than two years. The experimental apparatus was previously calibrated in efficiency to obtain absolute average burnup values, which were compared against corresponding ones furnished by reactor physics calculations. The mean deviation between both values amounts to 6%. (author)

  9. Burnup measurements on spent fuel elements of the RP-10 research reactor

    Vela Mora, Mariano; Gallardo Padilla, Alberto; Palomino, Jose Luis Castro, E-mail: mvela@ipen.gob.p [Instituto Peruano de Energia Nuclear (IPEN/Peru), Lima (Peru). Grupo de Calculo, Analisis y Seguridad de Reactores; Terremoto, Luis Antonio Albiac, E-mail: laaterre@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    This work describes the measurement, using nondestructive gamma-ray spectroscopy, of the average burnup attained by Material Testing Reactor (MTR) fuel elements irradiated in the RP-10 research reactor. Measurements were performed at the reactor storage pool area using {sup 137}Cs as the only burnup monitor, even for spent fuel elements with cooling times much shorter than two years. The experimental apparatus was previously calibrated in efficiency to obtain absolute average burnup values, which were compared against corresponding ones furnished by reactor physics calculations. The mean deviation between both values amounts to 6%. (author)

  10. Investor's and procurement guide South Africa. Pt. 1. Heavy minerals, rare earth elements, antimony

    Graupner, Torsten; Schwarz-Schampera, Ulrich [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Berlin (Germany); Hammond, Napoleon Q.; Opperman, Rehan; Long' a Tongu, Elisa; Kenan, Abdul O.; Nondula, Unathi; Tsanwani, Matamba [Council for Geoscience (CGS), Pretoria (South Africa). Dept. of Mineral Resources Development; Liedke, Maren; Marbler, Herwig [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Berlin (Germany). Deutsche Rohstoffagentur (DERA)

    2014-03-15

    This is the first part of the ''Investor's and Procurement Guide South Africa'', a handbook for investing and doing business in South Africa's mineral industry. It is anticipated that this publication will aid potential investors into considering South Africa as an investment destination, not only for raw materials, but also for related industries. This manual supplements the many publications available on the economic geology and mineral wealth in South Africa and has been designed to guide prospective and current investors, suppliers and mine equipment exporters through the process of doing business in Africa's biggest and dynamic economy. As well as detailing the mineral raw materials heavy minerals, rare-earth metals and antimony, the handbook provides a general introduction to South Africa and its infrastructure, the economical, political and judicial frame of the South African mining industry and an overview of the economic geology. South Africa has a long and complex geological history which dates back in excess of 3.6 billion years. The country has a vast mineral wealth, undoubtedly due to the fact that a significant proportion of the Archaean and younger rocks have been preserved. The mining of the enormous Witwatersrand gold deposits, commencing in 1886, has led to the establishment of South Africa's well-developed infrastructure and to the sustained growth of an industrial and service sector in the country. With the world's largest resources of PGMs, gold, chromite, vanadium and manganese and significant resources of iron, coal and numerous other minerals and metals, the minerals industry will continue to play a pivotal role in the growth of South Africa's economy in the foreseeable future. South Africa is one of the top destinations in Africa for foreign direct investments. South African headquartered companies have been major investors into foreign direct investments on the African continent in the past

  11. Co-ordinated research programme on nuclear techniques for toxic elements in foodstuffs

    1990-01-01

    This Co-ordinated Research Programme (CRP) was started by the Agency in 1985, within the framework of the Regional Cooperative Agreement for Research, Development and Training Related to Nuclear Science and Technology in the Asia and Pacific Region (RCA). Its main purpose has been to obtain comparative data on existing elemental concentrations of potentially toxic elements in foodstuffs in various Asian countries. The elements to be studied include the potentially most toxic trace elements (As, Cd, Hg, Pb, Se) as well as others of relevance to national monitoring programmes, such as Br, Cr, Cu, Fe, I, Mn, Sb, Tl, and Zn. An important supplementary purpose of the programme is to help establish analytical expertise for work of this kind in the individual countries. Scientists from several RCA Member States have participated in it, namely from Australia, Bangladesh, China, India, Indonesia, Japan, Malaysia, Pakistan, Thailand, and also from institutes in several countries outside the region, i.e., Argentina, Brazil, Jamaica and The Netherlands. This report summarizes the discussions that took place during the third and final Research Co-ordination Meeting (RCM) for the programme from 20-24 November 1989, in Jakarta, Indonesia. This document includes the progress reports presented by the participants as well as discussions and conclusions drawn from the meeting

  12. Research on the Hysteresis Effect on Positioning the System with Flexible Elements

    Audrius Čereška

    2015-03-01

    Full Text Available The paper analyzes the hysteresis phenomenon of positioning systems with flexible elements for transmitting motion of which piezoelectric actuators are used. The article investigates the influence of hysteresis on the accuracy of positioning systems. A special test bench for conducting research and stand-up methodology for carrying out experimental researches have been used. The test bench includes a computer piezo controller, an inductive displacement sensor and a dynamic data collector used for gathering data and transmitting it to the software package. Mathematical modelling of hysteresis using Matlab/Simulink software package has been done. The performed research has shown that the hysteresis model of maximum dispersion error compared to experimental results makes less than 5%. Thus, it can be stated that the selected method for hysteresis modelling is suitable for precision positioning systems having deformable elements and controlled employing piezoelectric actuators to model hysteresis.

  13. Water contamination with heavy metals and trace elements from Kilembe copper mine and tailing sites in Western Uganda; implications for domestic water quality.

    Abraham, Mwesigye R; Susan, Tumwebaze B

    2017-02-01

    The mining and processing of copper in Kilembe, Western Uganda, from 1956 to 1982 left over 15 Mt of cupriferous and cobaltiferous pyrite dumped within a mountain river valley, in addition to mine water which is pumped to the land surface. This study was conducted to assess the sources and concentrations of heavy metals and trace elements in Kilembe mine catchment water. Multi-element analysis of trace elements from point sources and sinks was conducted which included mine tailings, mine water, mine leachate, Nyamwamba River water, public water sources and domestic water samples using ICP-MS. The study found that mean concentrations (mg kg -1 ) of Co (112), Cu (3320), Ni (131), As (8.6) in mine tailings were significantly higher than world average crust and were being eroded and discharged into water bodies within the catchment. Underground mine water and leachate contained higher mean concentrations (μg L -1 ) of Cu (9470), Co (3430) and Ni (590) compared with background concentrations (μg L -1 ) in un contaminated water of 1.9, 0.21 and 0.67 for Cu, Co and Ni respectively. Over 25% of household water samples exceeded UK drinking water thresholds for Al of 200 μg L -1 , Co exceeded Winsconsin (USA drinking) water thresholds of 40 μg L -1 in 40% of samples while Fe in 42% of samples exceeded UK thresholds of 200 μg L -1 . The study however found that besides mining activities, natural processes of geological weathering also contributed to Al, Fe, and Mn water contamination in a number of public water sources. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. A Novel Synthesis Routine for Woodwardite and Its Affinity towards Light (La, Ce, Nd and Heavy (Gd and Y Rare Earth Elements

    Sirio Consani

    2018-01-01

    Full Text Available A synthetic Cu-Al-SO4 layered double hydroxide (LDH, analogue to the mineral woodwardite [Cu1−xAlx(SO4x/2(OH2·nH2O], with x < 0.5 and n ≤ 3x/2, was synthesised by adding a solution of Cu and Al sulphates to a solution with NaOH. The pH values were kept constant at 8.0 and 10.0 by a continuous addition of NaOH. The material obtained had poor crystallinity, turbostratic structure, and consisted of nanoscopic crystallites. The analyses performed in order to characterise the obtained materials (X-ray diffraction (XRD, thermogravimetry (TG, and Fourier Transform Infra-Red (FTIR spectroscopy showed that the Cu-Al-SO4 LDH is very similar to woodwardite, although it has a smaller layer spacing, presumably due to a lesser water content than in natural samples. The synthesis was performed by adding light rare earth elements (LREEs (La, Ce, and Nd and heavy rare earth elements (HREEs (Gd and Y in order to test the affinity of the Cu-Al-SO4 LDH to the incorporation of REEs. The concentration of rare earth elements (REEs in the solid fraction was in the range of 3.5–8 wt %. The results showed a good affinity for HREE and Nd, especially for materials synthesised at pH 10.0, whereas the affinities for Ce and La were much lower or non-existent. The thermal decomposition of the REE-doped materials generates a mixture of Cu, Al, and REE oxides, making them interesting as precursors in REE oxide synthesis.

  15. The Tevalac: A national facility for relativistic heavy-ion research to 10 GeV per nucleon with uranium

    1982-12-01

    This preliminary proposal addresses forefront physics research through the end of this century. It presents the implications of recent theoretical insights gained from relativistic heavy-ion studies that have led physicists to believe that the densities and temperatures needed to deconfine quarks from hadrons can be reached with only a ten-fold increase in beam energy beyond that available in today's highest-energy heavy-ion accelerators. In addition, the proposal describes a variety of other new and enhanced experimental opportunities that will be opened up by such an increase in projectile energy. Also presented are an accelerator concept, called the Tevalac, that provides the requisite 10-GeV/nucleon uranium beams and a program for research and development necessary to ensure that the facility to be proposed at a later date is ready for construction and will fit within the national program. Relativistic heavy-ion experiments using 1--2-GeV/nucleon beams have already demonstrated that high temperatures (of the order of 100 MeV) and high densities (up to four times normal nuclear density) are reached in head-on projectile-target collisions. Theoretical predictions now indicate a high probability that, when large amounts of nuclear matter are raised to the extreme temperatures and densities obtainable in head-on heavy-ion collisions at Tevalac beam energies, the quarks that constitute the individual nucleons will be deconfined: they will no longer be bound within individual nucleons, and a state of matter never before observed on earth--the quark-gluon plasma--will be created briefly. The investigation of the quark-gluon plasma will lead to unprecedented scientific opportunities and will serve as a bridge between conventional nuclear physics, which studies complex systems of particles, and high-energy physics, which studies the most fundamental constituents of matter

  16. Determination of the minimum number of fuel elements of the RP-10 research reactor

    Languasco, J.

    1989-01-01

    The peruvian research reactor RP-10 is composed of a compound nucleus of boxes containing fuel plates which are cooled with light water in order to remove heat produced by fission of uranium atoms. However from a certainty viewpoint, it exists certain restrictions to design the cooling system. The most admissible caloric flux of 90.3 watts/cm 2 is deflux of 90.3 watts/cm 2 is determined on the basis of these thermic restrictions when cooling speed is 409 cm/sec permitting at least 24 fuel elements(boxes) within the nucleus. On the basis of restrictions of load loss in the nucleus, it would be permitted at least 18 fuel elements, but this quantity breaks thermic restrictions for this reason, 24 boxes in the nucleus will be the minimum number of elements

  17. Uniform Distribution of Yttrium and Heavy Rare Earth Elements in Round Top Mountain Rhyolite Deposit , Sierra Blanca Texas, USA: Data, Significance, and Origin

    Pingitore, N. E., Jr.; Clague, J. W.; Gorski, D.

    2014-12-01

    The Round Top Mountain peraluminous rhyolite, exposed at the surface in Sierra Blanca, Hudspeth County, west Texas, USA, is enriched in yttrium and heavy rare earth elements (YHREEs). Other potentially valuable elements in the deposit include Be, Li, U, Th, Sn, F, Nb, and Ta. Texas Rare Earth Resources Corp. proposes to extract the YHREEs from the host mineral variety yttrofluorite by inexpensive heap leaching with dilute sulfuric acid, which also releases some of the Be, Li, U, F, and Th from other soluble minor minerals. Data: Feldspars and quartz comprise 90-95% of the rhyolite, with pheonocrysts of up to 250 microns set in an aphanitic matrix that hosts the typically sub-micron target yttrofluorite. Reverse circulation cuttings from some 100 drill holes, two drill cores, and outcrop and trench observations suggest striking physical homogeneity through this billion-plus ton surface-exposed laccolith, about 1200 feet high and a mile in diameter (375 x 1600 m). Gray to pink, and other minor hues, color variation derives from magnetite—hematite redox reaction. Plots of Y, 13 REEs, U, Th, and Nb analyses from over 1500 samples collected from 64 drill holes (color codes in figure) exhibit remarkably little variation in the concentration of these elements with geographic position or depth within the laccolith. Importance: Uniform mineralization grades help insure against the mining production surprises often associated with vein deposits and heterogeneous open pit deposits. At Round Top, mine feedstock can be relatively constant over the life of the mine (multiple decades), so the mechanical mining process can be optimized early on and not need expensive alterations later. Likewise, the chemical and physical parameters of the heap leach can be perfected. The sensitive and expensive process of extraction of elements and element groups from the pregnant leach solution and purification also can be optimized. Origin: The remarkable homogeneity of the YHREE distribution

  18. Proceedings of study meeting on microscopic and phenomenological research of interaction for light heavy-ion systems

    1991-06-01

    The Research Center for Nuclear Physics study meeting 'Microscopic and phenomenological research of interaction for light heavy-ion systems was held on March 7-9, 1990 as the study meeting in the second half of 1990, and 25 researchers took part in it. As the background of holding this study meeting, the fact that recently the rainbow scattering due to nuclear force was discovered experimentally in 16 O- 16 O system, and phenomenologically it was explained only by deep inter-nucleus potential. This should be evaluated as an important foothold for the research on the interaction for light heavy-ion systems and nuclear reaction mechanism. Accordingly, most of the papers presented this time were those related to the inter-nucleus potential and nuclear reaction mechanism. Also the development of theoretical analysis method was carried out and reported. Further, recently the experimental study on the structure and reaction of the neutron rich nucleus has advanced, and the theoretical research related to this topic was reported. (K.I.)

  19. The time resolved SBS and SRS research in heavy water and its application in CARS

    Liu, Jinbo; Gai, Baodong; Yuan, Hong; Sun, Jianfeng; Zhou, Xin; Liu, Di; Xia, Xusheng; Wang, Pengyuan; Hu, Shu; Chen, Ying; Guo, Jingwei; Jin, Yuqi; Sang, Fengting

    2018-05-01

    We present the time-resolved character of stimulated Brillouin scattering (SBS) and backward stimulated Raman scattering (BSRS) in heavy water and its application in Coherent Anti-Stokes Raman Scattering (CARS) technique. A nanosecond laser from a frequency-doubled Nd: YAG laser is introduced into a heavy water cell, to generate SBS and BSRS beams. The SBS and BSRS beams are collinear, and their time resolved characters are studied by a streak camera, experiment show that they are ideal source for an alignment-free CARS system, and the time resolved property of SBS and BSRS beams could affect the CARS efficiency significantly. By inserting a Dye cuvette to the collinear beams, the time-overlapping of SBS and BSRS could be improved, and finally the CARS efficiency is increased, even though the SBS energy is decreased. Possible methods to improve the efficiency of this CARS system are discussed too.

  20. Ecotoxicological characteristic of a soil polluted by radioactive elements and heavy metals before and after its bioremediation

    Georgiev, P.; Groudev, S.; Spasova, I.; Nikolova, M.

    2012-04-01

    Cinnamon soils from southeastern Bulgaria are heavily polluted with radionuclides (uranium, radium) and toxic heavy metals (copper and lead) due to the winds transportation of fine particles from flotation dumps to the soil surface. As a result of this, the polluted soils are characterized by a slightly alkaline pH (7.82) and positive net neutralization potential (+136.8 kg CaCO3/t). A fresh sample of cinnamon soil was subjected to remediation under laboratory conditions in four lysimeters each containing 70 kg of soil. The preliminary study revealed that most of the pollutants were presented as carbonate, reducible and oxidisable mobility fractions, i.e. pollutants ions were specifically adsorbed by carbonate and ferric iron minerals or were capsulated in sulfides. The applied soil treatment was connected with leaching of the pollutants located mainly in the horizon A, their transportation through the soil profile as soluble forms, and their precipitation in the rich-in-clay subhorizon B3. The efficiency of leaching depended on the activity of the indigenous microflora and on the chemical processes connected with solubilization of pollutants and formation of stable complexes with some organic compounds, chloride and hydrocarbonate ions. These processes were considerably enhanced by adding hay to the horizon A and irrigating the soil with water solutions containing the above-mentioned ions and some nutrients. After 18 months of treatment, each of the soil profiles in the different lysimeters was divided into five sections reflecting the different soil layers. The soil in these sections was subjected to a detailed chemical analysis and the data obtained were compared with the relevant data obtained before the start of the experiment. The best leaching of pollutants from horizon A was measured in the variants where soil mulching was applied. For example, the best leaching of lead (54.5 %) was found in the variant combining this technique and irrigation with solutions

  1. A 2 MV heavy ion Van de Graaff implanter for research and development

    Hemment, P.L.F.; Sealy, B.J.; Stephens, K.G.; Mynard, J.E.; Jeynes, C.; Browton, M.D.; Wilson, R.J.; Ma, M.X.; Cansell, A.; Mous, D.J.W.; Koudijs, R.

    1993-01-01

    A high energy heavy ion implantation system is described which is based upon a 2 MV High Voltage Engineering Europa Van de Graaff accelerator, which incorporates an ion source rapid exchange mechanism. The design and performance are described with particular reference to the system mass resolution, beam transport and performance of a sputter ion source. The system is used to provide a wide ranging implantation service and also supports material science studies, some of which are described briefly. (orig.)

  2. Heavy methanes (mass-20 and -21) as atmospheric tracers. A new research initiatives project

    Guthals, P.R.; Fowler, M.M.

    1978-07-01

    Products from the stable isotope production project (ICONS) at the Los Alamos Scientific Laboratory (LASL) have had applications in a number of practical problems. Fully deuterated methanes, using 12 C and 13 C (mass-20 and -21, respectively), are detectable in the atmosphere at very low concentrations. The detection limits are due to an almost zero background and a distinct mass-spectrometric line. These properties, coupled with long lifetimes in the atmosphere, make the heavy methanes strong candidates for tracers of atmospheric transport and turbulence on regional to global scales. Three field tests have been conducted to assess the feasibility and to demonstrate the desirable properties of heavy methanes as atmospheric tracers. In the first test in May 1974, heavy methane released at the Idaho National Engineering Laboratory (INEL) was sampled and detected in several midwestern cities up to 2500 km downstream. These results agree with trajectories estimated from observed meteorological data. A second experiment, conducted in December 1975 at the Savannah River Plant, compared two heavy methanes with SF 6 and 85 Kr over a transport distance of 100 km. Increased detail in meteorological support data and ground-level sampling offered options of data interpretation unavailable in the first test. Qualitative patterns of tracer concentrations show good agreement among the four tracers and are verified by the meteorological inputs. The third experiment, performed in April 1977 at INEL, built on the experience of the previous two. Detailed ground-level sampling arrays at 3, 50, and 90 km from the release point were supplemented by aircraft and a crude sampling line across the Continental Divide at 300-km distance. Two new perfluorocarbon tracers were included for comparison

  3. Two reports: (i) Correlation properties of delayed neutrons from fast neutron induced fission. (ii) Method and set-up for measurements of trace level content of heavy fissionable elements based on delayed neutron counting

    Piksaikin, V.M.; Isaev, S.G.; Goverdovski, A.A.; Pshakin, G.M.

    1998-10-01

    The document includes the following two reports: 'Correlation properties of delayed neutrons from fast neutron induced fission' and 'Method and set-up for measurements of trace level content of heavy fissionable elements based on delayed neutron counting. A separate abstract was prepared for each report

  4. Finding an optimization of the plate element of Egyptian research reactor using genetic algorithm

    Wahed, M.; Ibrahim, W.; Effat, A.

    2008-01-01

    The second Egyptian research reactor ET-RR-2 went critical on the 27th of November 1997. The National Center of Nuclear Safety and Radiation Control (NCNSRC) has the responsibility of the evaluation and assessment of the safety of this reactor. The purpose of this paper is to present an approach to optimization of the fuel element plate. For an efficient search through the solution space we use a multi objective genetic algorithm which allows us to identify a set of Pareto optimal solutions providing the decision maker with the complete spectrum of optimal solutions with respect to the various targets. The aim of this paper is to propose a new approach for optimizing the fuel element plate in the reactor. The fuel element plate is designed with a view to improve reliability and lifetime and it is one of the most important elements during the shut down. In this present paper, we present a conceptual design approach for fuel element plate, in conjunction with a genetic algorithm to obtain a fuel plate that maximizes a fitness value to optimize the safety design of the fuel plate. (authors)

  5. Sports participation and alcohol use among adolescents: the impact of measurement and other research design elements.

    Mays, Darren; Gatti, Margaret E; Thompson, Nancy J

    2011-06-01

    Sports participation, while offering numerous developmental benefits for adolescents, has been associated with alcohol use in prior research. However, the relationship between sports participation and alcohol use among adolescents remains unclear, particularly how research design elements impact evidence of this relationship. We reviewed the evidence regarding sports participation and alcohol use among adolescents, with a focus on examining the potential impact of research design elements on this evidence. Studies were assessed for eligibility and coded based on research design elements including: study design, sampling method, sample size, and measures of sports participation and alcohol use. Fifty-four studies were assessed for eligibility, 29 of which were included in the review. Nearly two-thirds used a cross-sectional design and a random sampling method, with sample sizes ranging from 178 to 50,168 adolescents (Median = 1,769). Sixteen studies used a categorical measure of sports participation, while 7 applied an index-type measure and 6 employed some other measure of sports participation. Most studies assessed alcohol-related behaviors (n = 18) through categorical measures, while only 6 applied frequency only measures of alcohol use, 1 study applied quantity only measures, and 3 studies used quantity and frequency measures. Sports participation has been defined and measured in various ways, most of which do not differentiate between interscholastic and community-based contexts, confounding this relationship. Stronger measures of both sports participation and alcohol use need to be applied in future studies to advance our understanding of this relationship among youths.

  6. Researches on Mathematical Relationship of Five Elements of Containing Notes and Fibonacci Sequence Modulo 5

    Zhaoxue Chen

    2015-01-01

    Full Text Available Considering the five periods and six qi’s theory in TCM almost shares a common basis of stem-branch system with the five elements of containing notes, studying the principle or mathematical structure behind the five elements of containing notes can surely bring a novel view for the five periods and six qi’s researches. By analyzing typical mathematical rules included in He tu, Luo shu, and stem-branch theory in TCM as well as the Fibonacci sequence especially widely existent in the biological world, novel researches are performed on mathematical relationship between the five elements of containing notes and the Fibonacci sequence modulo 5. Enlightened by elementary Yin or Yang number grouping principle of He tu, Luo shu, the 12534 and 31542 key number series of Fibonacci sequence modulo 5 are obtained. And three new arrangements about the five elements of containing notes are then introduced, which have shown close relationship with the two obtained key subsequences of the Fibonacci sequence modulo 5. The novel discovery is quite helpful to recover the scientific secret of the five periods and six qi’s theory in TCM as well as that of whole traditional Chinese culture system, but more data is needed to elucidate the TCM theory further.

  7. Mechanical properties of UO{sub 2} thin films under heavy ion irradiation using nanoindentation and finite element modeling

    Elbakhshwan, Mohamed S., E-mail: elbakhs1@illinois.edu; Miao, Yinbin; Stubbins, James F.; Heuser, Brent J.

    2016-10-15

    The mechanical response of UO{sub 2} to irradiation is becoming increasingly important due to the shift to higher burn-up rates in the next generation of nuclear reactors. In the current study, thin films of UO{sub 2} were deposited on YSZ substrates using reactive-gas magnetron sputtering. Nanoindentation was used to measure the mechanical properties of the as-grown and irradiated films. Finite element modeling was used to account for the substrate effect on the measurements. In order to study the effect of displacement cascades accompanying gas bubbles, 5000 Å UO{sub 2} films were irradiated with 600 keV Kr{sup +} ions at 25 °C and 600 °C. These irradiation conditions were used to confine radiation damage effects and implanted gas within the film. Results showed an increase in the film hardness and yield strength with dose, while elastic modulus initially decreased with irradiation and then kept increasing with dose. The change in hardness and elastic modulus is attributed to the introduction of gas bubbles and displacement cascade damage. Irradiation at 600 °C resulted in a decrease in the hardness and elastic modulus after irradiation using 600 keV Kr{sup +} at a dose of 1E14 ions/cm{sup 2}. Both hardness and elastic modulus then increased with irradiation dose. This behavior is attributed to recrystallization during irradiation at 600 °C and the formation of nanocrystallite regions with diameter and density that increase with dose. The calculation of the critical resolved shear stress (CRSS) demonstrated that nanocrystals are the primary cause for film hardening based on the Orowan hardening mechanism.

  8. Performance Data Report: Space Medicine Division, Human Research Program, Behavioural Health and Performance Research Element

    Shea, Camille; Keeton, Kathryn E.; Schmidt, Lacey L.; Slack, Kelley J.; Patterson, Holly N.; Leveton, Lauren B.; Holland, Albert W.

    2012-01-01

    This report is the result of a collaborative effort between NASA?s Behavioral Health & Performance (BHP) Research and Operations Group to investigate and determine the availability of data pertaining to behavioral performance (and other pertinent variables) that have been collected by the laboratories at NASA?s Johnson Space Center. BHP?s Operations and Research groups collaborated to systematically identify what types of performance data are needed in relevant BHP performance domains and also to conduct structured interviews with NASA personnel to identify which data do or do not exist currently (and for instances where such data exist, to evaluate the type, quality, accessibility, and confidentiality of those data). The authors defined outcome categories of performance that encapsulate BHP performance domains, mapped BHP Research Risks and Gaps onto those performance outcome categories, and identified and prioritized indicators for each outcome category. The team identified key points of contact (subject matter experts [SMEs]) as potential interviewees, created a template for structured interview questions about sources and accessibility of performance data, and coordinated and conducted structured interviews with the SMEs. The methodology, results, and implications of this effort, as well as forward work needed, are discussed in this report.

  9. Research Regarding the Accumulation in Soybeans of Heavy Metals from Anaerobic Composted Sewage Sludge Used as Organic Fertilizer

    Benoni Lixandru

    2010-10-01

    Full Text Available In sewage sludge from urban wastewater treatment stations can often be find high levels of Ni, Pb, Cu, Zn, Mn andCd. Aerobic or anaerobic composting of this sewage sludge does not eliminate the possibility of bioaccumulation ofthese metals in plants through metabolic processes of phytoextraction type. Researches regarding the accumulationdegree of heavy metals through phytoextraction processes were performed on soybean plants (Glycine max, Condorvariety. Plants were fertilized with anaerobic composted sludge in amounts of 25 t of / ha, 50 t / ha and 100 t / ha.The chemical analysis was done on an average sample of three repetitions. Metal concentration in soybeans wasanalyzed by reporting to the maximum allowance level for sheep, considered one of the most sensitive farm speciesto heavy metal toxicity. Our results showed a higher level than normal with 5.8 mg / kg only in the case of copperions. Zn, Pb, Mn and Cd concentration in soybeans was below the maximum allowance limits set by the rules offeeding farm animals. Also, heavy metal content of soybeans was not affected by the amount of composted sludgeused as fertilizer.

  10. Source Regions of the Interplanetary Magnetic Field and Variability in Heavy-Ion Elemental Composition in Gradual Solar Energetic Particle Events

    Ko, Yuan-Kuen; Tylka, Allan J.; Ng, Chee K.; Wang, Yi-Ming; Dietrich, William F.

    2013-01-01

    Gradual solar energetic particle (SEP) events are those in which ions are accelerated to their observed energies by interactions with a shock driven by a fast coronal mass-ejection (CME). Previous studies have shown that much of the observed event-to-event variability can be understood in terms of shock speed and evolution in the shock-normal angle. But an equally important factor, particularly for the elemental composition, is the origin of the suprathermal seed particles upon which the shock acts. To tackle this issue, we (1) use observed solar-wind speed, magnetograms, and the PFSS model to map the Sun-L1 interplanetary magnetic field (IMF) line back to its source region on the Sun at the time of the SEP observations; and (2) then look for correlation between SEP composition (as measured by Wind and ACE at approx. 2-30 MeV/nucleon) and characteristics of the identified IMF-source regions. The study is based on 24 SEP events, identified as a statistically-significant increase in approx. 20 MeV protons and occurring in 1998 and 2003-2006, when the rate of newly-emergent solar magnetic flux and CMEs was lower than in solar-maximum years and the field-line tracing is therefore more likely to be successful. We find that the gradual SEP Fe/O is correlated with the field strength at the IMF-source, with the largest enhancements occurring when the footpoint field is strong, due to the nearby presence of an active region. In these cases, other elemental ratios show a strong charge-to-mass (q/M) ordering, at least on average, similar to that found in impulsive events. These results lead us to suggest that magnetic reconnection in footpoint regions near active regions bias the heavy-ion composition of suprathermal seed ions by processes qualitatively similar to those that produce larger heavy-ion enhancements in impulsive SEP events. To address potential technical concerns about our analysis, we also discuss efforts to exclude impulsive SEP events from our event sample.

  11. Research on trace elements in biomedicine carried out in Italy using nuclear accelerators

    Moro, R.

    1985-01-01

    The present status and perspectives of research on trace elements in biomedicine carried out at Catania, Milan, Naples and Padua-Legnaro are discussed. In these researches, nuclear techniques such as Proton Induced X-ray Emission (PIXE), Proton Nuclear Activation (PNA) and Prompt Radiation Analysis (PRA), involving the use of small accelerators, are employed as analytical methods. Different field of application such as dentistry, bone disease, pediatrics and oncology are covered by these activities. The PIXE method is employed for the analysis of serum, hair and bone. In particular, elements like zinc and selenium which play an important role in infancy and oncology, respectively, have been extensively studied. The proton activation method has been applied to investigate the ferrokinetics in plasma. The prompt radiation analysis of the reaction /sup 19/F(p,α) has been used for the determination of the fluorine depth distribution in dental enamel

  12. Human Health Countermeasures (HHC) Element Management Plan: Human Research Program. Revision B

    Norsk, Peter; Baumann, David

    2012-01-01

    NASA s Human Research Program (HRP) is an applied research and technology program within the Human Exploration and Operations Mission Directorate (HEOMD) that addresses human health and performance risk mitigation strategies in support of exploration missions. The HRP research and technology development is focused on the highest priority risks to crew health and safety with the goal of ensuring mission success and maintaining long-term crew health. Crew health and performance standards, defined by the NASA Chief Health and Medical Officer (CHMO), set the acceptable risk level for exploration missions. The HRP conducts research to inform these standards as well as provide deliverables, such as countermeasures, that ensure standards can be met to maximize human performance and mission success. The Human Health Countermeasures (HHC) Element was formed as part of the HRP to develop a scientifically-based, integrated approach to understanding and mitigating the health risks associated with human spaceflight. These health risks have been organized into four research portfolios that group similar or related risks. A fifth portfolio exists for managing technology developments and infrastructure projects. The HHC Element portfolios consist of: a) Vision and Cardiovascular; b) Exercise and Performance; c) Multisystem; d) Bone; and e) Technology and Infrastructure. The HHC identifies gaps associated with the health risks and plans human physiology research that will result in knowledge required to more fully understand risks and will result in validated countermeasures to mitigate risks.

  13. Comparing geological and statistical approaches for element selection in sediment tracing research

    Laceby, J. Patrick; McMahon, Joe; Evrard, Olivier; Olley, Jon

    2015-04-01

    Elevated suspended sediment loads reduce reservoir capacity and significantly increase the cost of operating water treatment infrastructure, making the management of sediment supply to reservoirs of increasingly importance. Sediment fingerprinting techniques can be used to determine the relative contributions of different sources of sediment accumulating in reservoirs. The objective of this research is to compare geological and statistical approaches to element selection for sediment fingerprinting modelling. Time-integrated samplers (n=45) were used to obtain source samples from four major subcatchments flowing into the Baroon Pocket Dam in South East Queensland, Australia. The geochemistry of potential sources were compared to the geochemistry of sediment cores (n=12) sampled in the reservoir. The geochemical approach selected elements for modelling that provided expected, observed and statistical discrimination between sediment sources. Two statistical approaches selected elements for modelling with the Kruskal-Wallis H-test and Discriminatory Function Analysis (DFA). In particular, two different significance levels (0.05 & 0.35) for the DFA were included to investigate the importance of element selection on modelling results. A distribution model determined the relative contributions of different sources to sediment sampled in the Baroon Pocket Dam. Elemental discrimination was expected between one subcatchment (Obi Obi Creek) and the remaining subcatchments (Lexys, Falls and Bridge Creek). Six major elements were expected to provide discrimination. Of these six, only Fe2O3 and SiO2 provided expected, observed and statistical discrimination. Modelling results with this geological approach indicated 36% (+/- 9%) of sediment sampled in the reservoir cores were from mafic-derived sources and 64% (+/- 9%) were from felsic-derived sources. The geological and the first statistical approach (DFA0.05) differed by only 1% (σ 5%) for 5 out of 6 model groupings with only

  14. Quantum Biology at the Cellular Level - elements of the research program

    Bordonaro, Michael; Ogryzko, Vasily

    2013-01-01

    Quantum Biology is emerging as a new field at the intersection between fundamental physics and biology, promising novel insights into the nature and origin of biological order. We discuss several elements of QBCL (Quantum Biology at Cellular Level), a research program designed to extend the reach of quantum concepts to higher than molecular levels of biological organization. Key words. decoherence, macroscopic superpositions, basis-dependence, formal superposition, non-classical correlations,...

  15. Research on Correlation between Vehicle Cycle and Engine Cycle in Heavy-duty commercial vehicle

    lin, Chen; Zhong, Wang; Shuai, Liu

    2017-12-01

    In order to study the correlation between vehicle cycle and engine cycle in heavy commercial vehicles, the conversion model of vehicle cycle to engine cycle is constructed based on the vehicle power system theory and shift strategy, which considers the verification on diesel truck. The results show that the model has high rationality and reliability in engine operation. In the acceleration process of high speed, the difference of model gear selection leads to the actual deviation. Compared with the drum test, the engine speed distribution obtained by the model deviates to right, which fits to the lower grade. The grade selection has high influence on the model.

  16. Automation in trace-element chemistry - Development of a fully automated on-line preconcentration device for trace analysis of heavy metals with atomic spectroscopy

    Michaelis, M.R.A.

    1990-01-01

    Scope of this work was the development of an automated system for trace element preconcentration to be used and integrated to analytic atomic spectroscopic methods like flame atomic absorption spectrometry (FAAS), graphite furnace atomic absorption spectrometry (GFAAS) or atomic emission spectroscopy with inductively coupled plasma (ICP-AES). Based on the newly developed cellulose-based chelating cation exchangers ethylene-diamin-triacetic acid cellulose (EDTrA-Cellulose) and sulfonated-oxine cellulose a flexible, computer-controlled instrument for automation of preconcentration and/or of matrix separation of heavy metals is described. The most important properties of these materials are fast exchange kinetics, good selectivity against alkaline and alkaline earth elements, good flow characteristics and good stability of the material and the chelating functions against changes in pH-values of reagents necessary in the process. The combination of the preconcentration device for on-line determinations of Zn, Cd, Pb, Ni, Fe, Co, Mn, V, Cu, La, U, Th is described for FAAS and for ICP-AES with a simultaneous spectrometer. Signal enhancement factors of 70 are achieved from preconcentration of 10 ml and on-line determination with FAAS due to signal quantification in peak-height mode. For GFAAS and for sequential ICP methods for off-line preconcentration are given. The optimization and adaption of the interface to the different characteristics of the analytical instrumentation is emphasized. For evaluation and future developments with respect to determination and/or preconcentration of anionic species like As, Se, Sb etc. instrument modifications are proposed and a development software is described. (Author)

  17. Analysis of heavy metals and minerals elements in the turmeric using Total-Reflection X-ray Fluorescence analysis technique and Atomic Absorption Spectrometry

    Andriamisetra, V.M.Z.

    2014-01-01

    Currently, many studies demonstrate anti-cancer and anti-inflammatory benefits of turmeric. The aims of this work is to perform analysis of metals such as calcium, chromium, manganese, iron, cobalt, nickel, copper, zinc, arsenic, bromine, rubidium, strontium, cadmium and lead in the turmeric collected from various places in Madagascar. The analysis by total reflection X-ray fluorescence technique is used to determine the concentrations of heavy metals, while the atomic absorption spectrometry is used for the determination of trace elements. Analysis results show that the concentration of calcium in the turmeric is very high, its average concentration is 1025.8 mg.kg -1 . The average concentrations of manganese, of copper and of iron are respectively 44.7 mg.kg -1 ; 19.7 mg.kg -1 and 53.6 mg.kg -1 . The average concentrations of zinc, of rubidium and of strontium are respectively 17.3 mg.kg -1 ; 35.2 mg.kg -1 and 21.7 mg.kg -1 [fr

  18. Co-ordinated research programme on nuclear techniques for toxic elements in foodstuffs

    1988-01-01

    The purpose of this Co-ordinated Research Programme (CRP) is to obtain comparative data on the existing elemental concentrations of potentially toxic elements in foodstuffs in various countries. This study is also intended to provide information on the dietary intakes of toxic elements as a means to detect potential health hazards to the population groups concerned. This study has important economic implications since trade in foodstuffs is dependent on compliance with regulations pertaining to maximum permissible concentrations. An important supplementary purpose of the programme is to help establish analytical expertise for work of this kind in individual countries, allowing such laboratories to offer analytical quality control services. The programme has centred its objective on the determination of important toxic elements such as As, Cd, Cr, Hg, Pb and Se, in addition to Cu, Sb and Zn, which are also potentially toxic but are generally of minor importance from the point of view of public health. The matrices of interest are foodstuffs which comprise together more than 50% of the average daily intake. Drinking water is also of high importance and should be analysed as well. Refs, figs and tabs

  19. Eddy current examination of the nuclear fuel elements of IPR-R1 research reactor

    Silva, Roger F.; Frade, Rangel T.; Oliveira, Paulo F.; Silva, Marlucio A.; Silva Junior, Silverio F.

    2015-01-01

    Tubes of AISI 304 stainless steel as well as tubes of Aluminum 1100-F are used as cladding of the fuel elements of TRIGA MARK 1 nuclear research reactor. Usually, these tubes are periodically inspected by means of visual test and sipping test. The visual test allows the detection of changes occurred at the external fuel elements surface, such as those promoted by corrosion processes. However, this test method cannot be used for detection of internal discontinuities at the tube walls. Sipping test allows the detection of fuel elements in which the cladding has failed, but it is not able to determine the place where the discontinuity is located. In turn, eddy current testing, an electromagnetic nondestructive test method, allows the detection of discontinuities and monitoring their growth. In this paper, a study about the use of eddy current testing for detection and characterization of discontinuities in the fuel elements cladding is proposed. The study involves the development of probes able to operate in underwater inspections, the design and manufacture of reference standards and the development of a test methodology to perform the evaluations. (author)

  20. Eddy current examination of the nuclear fuel elements of IPR-R1 research reactor

    Silva, Roger F.; Frade, Rangel T.; Oliveira, Paulo F.; Silva, Marlucio A.; Silva Junior, Silverio F., E-mail: rfs@cdtn.br, E-mail: rtf@cdtn.br, E-mail: pfo@cdtn.br, E-mail: mas@cdtn.br, E-mail: silvasf@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2015-07-01

    Tubes of AISI 304 stainless steel as well as tubes of Aluminum 1100-F are used as cladding of the fuel elements of TRIGA MARK 1 nuclear research reactor. Usually, these tubes are periodically inspected by means of visual test and sipping test. The visual test allows the detection of changes occurred at the external fuel elements surface, such as those promoted by corrosion processes. However, this test method cannot be used for detection of internal discontinuities at the tube walls. Sipping test allows the detection of fuel elements in which the cladding has failed, but it is not able to determine the place where the discontinuity is located. In turn, eddy current testing, an electromagnetic nondestructive test method, allows the detection of discontinuities and monitoring their growth. In this paper, a study about the use of eddy current testing for detection and characterization of discontinuities in the fuel elements cladding is proposed. The study involves the development of probes able to operate in underwater inspections, the design and manufacture of reference standards and the development of a test methodology to perform the evaluations. (author)

  1. Development of a transport cask for spent fuel elements of research reactors

    Quintana, F.; Saliba, R.O.; Furnari, J.C.; Mourao, R.P; Leite da Silva, L.; Novara, O.; Alexandre Miranda, C.; Mattar Neto, M.

    2012-01-01

    This article presents an overview of the development of a research reactor spent fuel transport cask. Through a project funded by the IAEA, Argentina, Brazil and Chile have collaborated to enhance regional capacity in the management of spent fuel elements from research reactors operated in the region. A packaging for the transport of research reactors spent fuel was developed. It was designed by a team of researchers from the countries mentioned and a 1:2 scale model for MTR type fuel was constructed in Argentina and subsequently tested in CDTN facilities in Belo Horizonte, Brazil. There were three test sequences to test the cask for normal transport and hypothetical accident conditions. It has successfully passed the tests and the overall performance was considered satisfactory. As part of the licensing process, a test sequence with the presence of regulatory authorities is scheduled for December, 2012 (author)

  2. RESEARCH ON THE QUAIL EGGS ALBUMEN CONTENT IN SOME HEAVY METALS

    I. VIZITIU

    2015-12-01

    Full Text Available Out of a sample batch of 20 Japanese quails, Pharaoh race, with an age of 100 days and weighing 245 g, approximately 200 eggs were collected at the peak phase of the laying period. The eggs were measured, weighed and broken, separating the albumen from the other components. The data obtained served to calculate the physical and morphological indices. Primary chemical composition, caloricity, heavy metals content were first determined, the following data being obtained: quail eggs albumen has an average weight of 7.1025±0.061g, an average volume of 7.158±0.09cm3, an average density of 1.0168±0.0139 g/cm3 and an index (of freshness of 0.0797±0.0015. The albumen contains: 86.76% water, 13.24% dry matter, 0.835% mineral matter, 11.37% protein, 1.03% non-nitrogenous extractive substances and a caloricity of 289.498 kJ for 100 g product. The average content of heavy metals in albumen was: 1.33*10-3 ppm, for cadmium; 8.83*10-2 ppm, for zinc; 1.005 ppm, for cooper and 0.0 ppm, respectively, for lead.

  3. Research in the US on heavy ion drivers for inertial confinement fusion

    Celata, C.; Faltens, A.; Fessenden, T.J.

    1986-10-01

    The US study of high-energy multigap accelerators to produce large currents of heavy ions for inertial fusion is centered on the single-pass induction linac method. The large technology base associated with multigap accelerators for high-energy physics gives confidence that high efficiency, high repetition rate, and good availability can be achieved, and that the path from scientific demonstration to commercial realization can be a smooth one. In an induction linac driver, multiple (parallel) ion beams are accelerated through a sequence of pulsed transformers. Crucial to the design is the manipulation of electric fields to amplify the beam current during acceleration. A proof-of-principle induction linac experiment (MBE-4) is underway and has begun the first demonstration of current amplification, control of the bunch ends, and the acceleration of multiple beams. A recently completed experiment, called the Single Beam Transport Experiment has shown that we can now count on more freedom to design an alternating-gradient quadrupole focusing channel to transport much higher ion-beam currents than formerly believed possible. A recent Heavy Ion Fusion System Assessment (HIFSA) has shown that a substantial cost saving results from use of multiply-charged ions, and that a remarkably broad range of options exist for viable power-plant designs. The driver cost at 3 to 4 MJ could be $200/joule or less, and the cost of electricity in the range of 50 to 55 mills/kWhr

  4. Research on mutation generation in higher plants with heavy ions at NIRS-HIMAC

    Okamura, M.; Watanabe, S.; Watanabe, M.; Toguri, T.; Furusawa, Y.

    2006-01-01

    Plants are closely related to medical treatment in medicine, foods, herbs and medical care by gardening. Ion beams have much higher linear energy transfer (LET) and relative biological effectiveness than those of gamma rays and X-rays. Ion beams are supposed to be useful as new mutagen to obtain novel mutants with superior characteristics in higher plants. In this study, the influence of heavy ions irradiation on bud growth was examined in carnation and the mutation generation was inspected in babies' breath. The growth of carnation buds began to decrease at 10 Gy and the median growth dose was estimated at 35 Gy for 290 Mev/u carbon ion beams. Mutants with petaloid leaves were observed in babies' breath by the irradiation of 290 Mev/u carbon ion beams at 20Gy. We will examine the mutation rates and spectrum for 290 MeV/u carbon, 400 MeV/u neon and 500 MeV/u argon ion beams to find optimum use of the beams in plant breeding. The efficient system to generate useful mutants using heavy ions at NIRS-HIMAC will be developed in higher plants. (author)

  5. Design and research on the electronic parking brake system of the medium and heavy duty vehicles

    Hongliang WANG

    2015-04-01

    Full Text Available Focusing on auto control of parking brake system of the medium and heavy duty vehicles, the key problems are studied including the system design and control strategies. The structure and working principle of the parking brake system of the medium and heavy duty vehicles are analyzed. The functions of EPB are proposed. The important information of the vehicle are analyzed which could influence the EPB system. The overall plan of the pneumatic EPB system is designed, which adopts the two-position three-way electromagnetic valve with double coil as actuator. The system could keep the vehicle parking brake status or parking release status for a long time without power supply. The function modules of the system are planned, and the control strategies of automatic parking brake and parking release are made. The experiment is performed on a medium-sized commercial vehicle which is experimentally modified. The overall plan of the pneumatic EPB system and the automatic parking function are proved through real vehicle tests.

  6. Elements for harnessing participatory action research to strengthen health managers' capacity: a critical interpretative synthesis.

    Tetui, Moses; Zulu, Joseph Mumba; Hurtig, Anna-Karin; Ekirapa-Kiracho, Elizabeth; Kiwanuka, Suzanne N; Coe, Anna-Britt

    2018-04-19

    Health managers play a key role in ensuring that health services are responsive to the needs of the population. Participatory action research (PAR) is one of the approaches that have been used to strengthen managers' capacity. However, collated knowledge on elements for harnessing PAR to strengthen managers' capacity is missing. This paper bridges this gap by reviewing existing literature on the subject matter. A critical interpretive synthesis method was used to interrogate eight selected articles. These articles reported the use of PAR to strengthen health managers' capacity. The critical interpretive synthesis method's approach to analysis guided the synthesis. Here, the authors interpretively made connections and linkages between different elements identified in the literature. Finally, the Atun et al. (Heal Pol Plann, 25:104-111, 2010) framework on integration was used to model the elements synthesised in the literature into five main domains. Five elements with intricate bi-directional interactions were identified in the literature reviewed. These included a shared purpose, skilled facilitation and psychological safety, activity integration into organisational procedures, organisational support, and external supportive monitoring. A shared purpose of the managers' capacity strengthening initiative created commitment and motivation to learn. This purpose was built upon a set of facilitation skills that included promoting participation, self-efficacy and reflection, thereby creating a safe psychological space within which the managers interacted and learnt from each other and their actions. Additionally, an integrated intervention strengthened local capacity and harnessed organisational support for learning. Finally, supportive monitoring from external partners, such as researchers, ensured quality, building of local capacity and professional safety networks essential for continued learning. The five elements identified in this synthesis provide a basis upon

  7. Progress of the Russian RERTR program: Development of new-type fuel elements for Russian-built research reactors

    Vatulin, A. V.; Stetskiy, Y.A.; Mishunin, V.A.; Suprun, V.B.; Dobrikova, I.V.

    2002-01-01

    The new design of pin-type fuel elements and fuel assembly on their basis for Russian research reactors has been developed. The number of following activities has been performed: computational and experimental substantiation of fuel element design; development of fabrication process of fuel elements; manufacturing of experimental assembly for lifetime in-pile tests. The relevant fuel assemblies are considered to be perspective for usage as low-enriched fuel for Russian research reactors. (author)

  8. Neutron activation analysis for environmental trace element research determination of elemental composition of sediments in the Sea of Galillee, Israel

    Lavi, N; Ne` eman, E; Brenner, S; Butenko, V [Tel Aviv Univ. (Israel). Medical School

    1996-12-01

    The aims of this work were to: a) demonstrate the effectiveness of instrumental neutron activation analysis for determining the background concentrations of trace elements in the sediments collected from the Sea of Gallile. b) determine the advantage factors for epithermal neutron irradiation. c) determine the contribution of silicon to the total {sup 28}Al activity by the {sup 28}Si(n,p){sup 28}Al reaction. c) check the validity of the method by determining the elemental content of U.S. NBS Standard Reference Material SRM-1633a (fly ash). d) calculate the average enrichment factors for the elements in sediments . e) determine the concentrations of the artificial radionuclides {sup 134}Cs, {sup 137}Cs and the naturally occurring radionuclides {sup 40}K, {sup 226}Ra and {sup 232}Th (authors).

  9. Study of the behaviour of some heavy elements in solvents containing hydrogen fluoride; Etude du comportement de quelques elements lourds dans des solvants a base d'acide fluorhydrique

    Tarnero, M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1967-01-01

    The anhydrous liquid mixtures: dinitrogen tetroxide-hydrogen fluoride and antimony pentafluoride-hydrogen fluoride were studied as solvents for heavy elements interesting nuclear energy: uranium, thorium, zirconium and for some of their compounds. For N{sub 2}O{sub 4}-HF mixtures, electric conductivity measurements and liquid phase infrared spectra were also obtained. Uranium and zirconium tetrafluoride are much more soluble in N{sub 2}O{sub 4}-HF mixtures than in pure hydrogen fluoride. Uranium dissolved in these mixtures is pentavalent. In SbF{sub 5}-HF mixtures, uranium dissolves with hydrogen evolution and becomes trivalent. The solid compound resulting from the dissolution is a fluoro-antimonate: U(SbF{sub 6}){sub 3}. (author) [French] On a etudie les melanges liquides anhydres: peroxyde d'azote-acide fluorhydrique et pentafluorure d'antimoine-acide fluorhydrique comme solvants d'elements lourds interessant l'energie nucleaire: uranium, thorium, zirconium et de quelques uns de leurs composes. Pour les melanges N{sub 2}O{sub 4}-HF on a egalement effectue des mesures de conductivite electrique, ainsi que des spectres d'absorption infrarouge en phase liquide. Le tetrafluorure d'uranium et le tetrafluorure de zirconium sont beaucoup plus solubles dans les melanges N{sub 2}O{sub 4}-HF que dans l'acide fluorhydrique. L'uranium dissous dans ces melanges est a l'etat pentavalent. Dans les melanges SbF{sub 5}-HF l'uranium se dissout avec degagement d'hydrogene et passe a l'etat trivalent. Le compose solide resultant de la dissolution est un fluoantimoniate: U(SbF{sub 6}){sub 3}. (auteur)

  10. Thermal simulations and tests in the development of a helmet transport spent fuel elements Research Reactor

    Saliba, R.; Quintana, F.; Márquez Turiello, R.; Furnari, J.C.; Pimenta Mourão, R.

    2013-01-01

    A packaging for the transport of irradiated fuel from research reactors was designed by a group of researchers to improve the capability in the management of spent fuel elements from the reactors operated in the region. Two half-scale models for MTR fuel were constructed and tested so far and a third one for both MTR and TRIGA fuels will be constructed and tested next. Four test campaigns have been carried out, covering both normal and hypothetical accident conditions of transportation. The thermal test is part of the requirements for the qualification of transportation packages for nuclear reactors spent fuel elements. In this paper both the numerical modelling and experimental thermal tests performed are presented and discussed. The cask is briefly described as well as the finite element model developed and the main adopted hypotheses for the thermal phenomena. The results of both numerical runs and experimental tests are discussed as a tool to validate the thermal modelling. The impact limiters, attached to the cask for protection, were not modelled. (author) [es

  11. Elemental composition study of heavy metal (Ni, Cu, Zn) in riverbank soil by electrokinetic-assisted phyto remediation using XRF and SEM/EDX

    Suhailly Jamari; Zaidi Embong; Zaidi Embong; Ismail Bakar

    2013-01-01

    Full-text: Electrokinetic (EK)-assisted phyto remediation is one of the methods that have a big potential in enhancing the ability of plant uptake in soils remediation process. This research was conducted to investigate the difference in elemental composition concentration of riverbank soil and the change of pH between pre- and post-phyto remediation under the following condition: 1) control or as-receive sample; 2) Dieffenbachia spp plant with EK system (a pair of EK electrodes connected to a direct current (DC) power supply). After the electrodes were connected to a magnitude of 6 V/ cm -1 electric field for 4 hours/ day, the soil and plant samples were analyzed using and X-ray Fluorescence Spectrometer (XRF) and Scanning Electron Microscope/ Energy Dispersive X-ray Spectroscopy (SEM/ EDX). The SEM/EDX analysis showed that concentration of elemental composition (Ni, Cu and Zn) in post-phyto remediation plant powder samples had increase while elemental concentrations in the post-hydrotreatment soil samples were decreased. XRF analysis presented a variation in soil elemental composition concentration from anode to cathode where the concentration near anode region increased while decreased near the cathode region. A significant changes in soil pH were obtained where the soil pH increase in cathode region while decrease in anode region. The results reveal that the assistance of EK in phyto remediation process has increase the efficiency of plant uptake. (author)

  12. Elemental composition study of heavy metal (Ni, Cu, Zn) in riverbank soil by electrokinetic-assisted phytoremediation using XRF and SEM/EDX

    Jamari, Suhailly; Embong, Zaidi; Bakar, Ismail

    2014-01-01

    Electrokinetic (EK)-assisted phytoremediation is one of the methods that have a big potential in enhancing the ability of plant uptake in soils remediation process. This research was conducted to investigate the difference in elemental composition concentration of riverbank soil and the change of pH between pre- and post-phytoremediation under the following condition: 1) control or as-receive sample; 2) Dieffenbachia spp plant with EK system (a pair of EK electrodes connected to a direct current (DC) power supply). After the electrodes were connected to a magnitude of 6V/cm −1 electric field for 4 hours/day, the soil and plant samples were analyzed using and X-ray Fluorescence Spectrometer (XRF) and Scanning Electron Microscope / Energy Dispersive X-ray Spectroscopy (SEM/EDX). The SEM/EDX analysis showed that concentration of elemental composition (Ni, Cu and Zn) in post-phytoremediation plant powder samples had increase while elemental concentrations in the post-phytoremediation soil samples were decreased. XRF analysis presented a variation in soil elemental composition concentration from anode to cathode where the concentration near anode region increased while decreased near the cathode region. A significant changes in soil pH were obtained where the soil pH increase in cathode region while decrease in anode region. The results reveal that the assistance of EK in phytoremediation process has increase the efficiency of plant uptake

  13. Elemental composition study of heavy metal (Ni, Cu, Zn) in riverbank soil by electrokinetic-assisted phytoremediation using XRF and SEM/EDX

    Jamari, Suhailly [Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia (UTHM) (Malaysia); Embong, Zaidi [Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia (UTHM) and Research Center for Soft Soils (RECESS), Office of Research, Innovation, Commercialization and Consultancy Management - ORRIC, Universiti Tun Hussein (Malaysia); Bakar, Ismail [Research Center for Soft Soils (RECESS), Office of Research, Innovation, Commercialization and Consultancy Management (ORRIC), Universiti Tun Hussein Onn Malaysia -UTHM, 86400 Batu Pahat, Johor (Malaysia)

    2014-02-12

    Electrokinetic (EK)-assisted phytoremediation is one of the methods that have a big potential in enhancing the ability of plant uptake in soils remediation process. This research was conducted to investigate the difference in elemental composition concentration of riverbank soil and the change of pH between pre- and post-phytoremediation under the following condition: 1) control or as-receive sample; 2) Dieffenbachia spp plant with EK system (a pair of EK electrodes connected to a direct current (DC) power supply). After the electrodes were connected to a magnitude of 6V/cm{sup −1} electric field for 4 hours/day, the soil and plant samples were analyzed using and X-ray Fluorescence Spectrometer (XRF) and Scanning Electron Microscope / Energy Dispersive X-ray Spectroscopy (SEM/EDX). The SEM/EDX analysis showed that concentration of elemental composition (Ni, Cu and Zn) in post-phytoremediation plant powder samples had increase while elemental concentrations in the post-phytoremediation soil samples were decreased. XRF analysis presented a variation in soil elemental composition concentration from anode to cathode where the concentration near anode region increased while decreased near the cathode region. A significant changes in soil pH were obtained where the soil pH increase in cathode region while decrease in anode region. The results reveal that the assistance of EK in phytoremediation process has increase the efficiency of plant uptake.

  14. Top Quark Produced Through the Electroweak Force: Discovery Using the Matrix Element Analysis and Search for Heavy Gauge Bosons Using Boosted Decision Trees

    Pangilinan, Monica [Brown Univ., Providence, RI (United States)

    2010-05-01

    The top quark produced through the electroweak channel provides a direct measurement of the Vtb element in the CKM matrix which can be viewed as a transition rate of a top quark to a bottom quark. This production channel of top quark is also sensitive to different theories beyond the Standard Model such as heavy charged gauged bosons termed W'. This thesis measures the cross section of the electroweak produced top quark using a technique based on using the matrix elements of the processes under consideration. The technique is applied to 2.3 fb-1 of data from the D0 detector. From a comparison of the matrix element discriminants between data and the signal and background model using Bayesian statistics, we measure the cross section of the top quark produced through the electroweak mechanism σ(p$\\bar{p}$ → tb + X, tqb + X) = 4.30-1.20+0.98 pb. The measured result corresponds to a 4.9σ Gaussian-equivalent significance. By combining this analysis with other analyses based on the Bayesian Neural Network (BNN) and Boosted Decision Tree (BDT) method, the measured cross section is 3.94 ± 0.88 pb with a significance of 5.0σ, resulting in the discovery of electroweak produced top quarks. Using this measured cross section and constraining |Vtb| < 1, the 95% confidence level (C.L.) lower limit is |Vtb| > 0.78. Additionally, a search is made for the production of W' using the same samples from the electroweak produced top quark. An analysis based on the BDT method is used to separate the signal from expected backgrounds. No significant excess is found and 95% C.L. upper limits on the production cross section are set for W' with masses within 600-950 GeV. For four general models of W{prime} boson production using decay channel W' → t$\\bar{p}$, the lower mass limits are the following: M(W'L with SM couplings) > 840 GeV; M(W'R) > 880 GeV or 890 GeV if the

  15. German concept and status of the disposal of spent fuel elements from German research reactors

    Komorowski, K.; Storch, S.; Thamm, G.

    1995-01-01

    Eight research reactors with a power ≥ 100 kW are currently being operated in the Federal Republic of Germany. These comprise three TRIGA-type reactors (power 100 kW to 250 kW), four swimming-pool reactors (power 1 MW to 10 MW) and one DIDO type reactor (power 23 MW). The German research reactors are used for neutron scattering for basic research in the field of solid state research, neutron metrology, for the fabrication of isotopes and for neutron activation analysis for medicine and biology, for investigating the influence of radiation on materials and for nuclear fuel behavior. It will be vital to continue current investigations in the future. Further operation of the German research reactors is therefore indispensable. Safe, regular disposal of the irradiated fuel elements arising now and in future operation is of primary importance. Furthermore, there are several plants with considerable quantities of spent fuel, the safe disposal of which is a matter of urgency. These include above all the VKTA facilities in Rossendorf and also the TRIGA reactors, where disposal will only be necessary upon decommissioning. The present paper report is concerned with the disposal of fuel from the German research reactors. It briefly deals with the situation in the USA since the end of 1988, describes interim solutions for current disposal requirements and then mainly concentrates on the German disposal concept currently being prepared. This concept initially envisages the long-term (25--50 years) dry interim storage of fuel elements in special containers in a central German interim store with subsequent direct final disposal without reprocessing of the irradiated fuel

  16. Human Research Program Human Health Countermeasures Element Nutrition Risk Standing Review Panel

    Bistrian, Bruce

    2009-01-01

    The Nutrition Risk Standing Review Panel (SRP) reviewed and discussed the specific gaps and tasks for the Human Health Countermeasures (HHC) Element related to nutrition identified in the Human Research Program (HRP) Integrated Research Plan. There was general consensus that the described gaps and proposed tasks were critical to future NASA mission success. The SRP acknowledged the high scientific quality of the work currently being undertaken by the Nutritional Biochemistry group under the direction of Dr. Scott Smith. In review of the entire HRP, four new gaps were identified that complement the Element's existing research activities. Given the limitations of ground-based analogs for many of the unique physiological and metabolic alterations in space, future studies are needed to quantify nutritional factors that change during actual space flight. In addition, future tasks should seek to better evaluate the time course of physiological and metabolic alterations during flight to better predict alterations during longer duration missions. Finally, given the recent data suggesting a potential role for increased inflammatory responses during space flight, the role of inflammation needs to be explored in detail, including the development of potential countermeasures and new ground based analogs, if this possibility is confirmed.

  17. Heavy Element Spectroscopy At JYFL

    Greenlees, P.T.; Eeckhaudt, S.; Grahn, T.; Jones, P.; Julin, R.; Juutinen, S.; Kankaanpaeae, H.; Keenan, A.; Kettunen, H.; Leino, M.; Leppaenen, A.-P.; Muikku, M.; Nieminen, P.; Pakarinen, J.; Rahkila, P.; Scholey, C.; Uusitalo, J.; Amzal, N.; Bastin, J.E.; Hammond, N.J.

    2005-01-01

    A series of experiments to study the properties of transfermium nuclei have been performed at the Department of Physics of the University of Jyvaeskylae. The experiments are carried out by a large group of collaborating institutes. These studies have been rendered possible by the coupling of various state-of-the-art detector systems to the RITU gas-filled recoil separator. In-beam conversion-electron and gamma-ray measurements have been made using the SACRED silicon and JuroGam germanium-detector arrays, respectively. The introduction of the GREAT spectrometer and TDR data acquisition system have greatly improved the quality of the data obtained at RITU. A brief overview of the instrumentation used and highlights from recent experiments are presented

  18. The use of irradiation zones in the fuel element lattice of research piles

    Delattre, P.; Genthon, J.P.

    1960-01-01

    The first part of this report examines the advantages and disadvantages of the various types of canal which may be found in the fuel element lattice of research piles. Some examples relative to the piles EL2 and EL3 are discussed in detail. From the conclusions drawn in the last part, several norms are extracted which make it possible to define the conditions the various canals must fulfil in order that they can be used to the best possible advantage for each type of irradiation. (author) [fr

  19. Control of criticality risk in the manufacture of fuel elements for research reactors

    Friedenthal, M.; Cardenas Yucra, H.R.; Marajofsky, A.; La Gamma de Batistoni, A.M.

    1987-01-01

    The control of criticality risk in a chemical plant adopts different forms according to the quantities of fissile material and the type of compounds used. This work presents the treatment of the critical excursion risk adopted in production plants of U 3 O 8 and manufacturing plants of fuel elements for research reactors, located in Constituyentes Atomic Center. The possible events and accidents related to the fissile material control are analyzed, and the systems of administrative control and intrinsic safety through engineering are described. (Author)

  20. Research reactors. Problems of fuel element enrichment reduction. Deliberations and comments

    1978-10-01

    This paper summarises the main data from the major research reactors in the Federal Republic of Germany utilising highly enriched uranium (HEU) and presently available fuel technology for their fuel elements. The required modification for an adaption of the fabrication to lower enriched fuel are considered as well as the consequences on reactor performance operation and licensing. On the basis of past experience with reactor modifications a rough estimate of 82 months is given for the conversion of a reactor to a modified type of fuel and of 70 months for a fuel test program. The conclusions reflect the own calculations and data from other papers submitted to INFCE-WG 8C