Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas

International Nuclear Information System (INIS)

Santos, Joyra Amaral dos

1999-08-01

This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

Electrochemical Decontamination of Painted and Heavily Corroded Metals

International Nuclear Information System (INIS)

Marczak, S.; Anderson, J.; Dziewinski, J.

1998-01-01

The radioactive metal wastes that are generated from nuclear fuel plants and radiochemical laboratories are mainly contaminated by the surface deposition of radioactive isotopes. There are presently several techniques used in removing surface contamination involving physical and chemical processes. However, there has been very little research done in the area of soiled, heavily oxidized, and painted metals. Researchers at Los Alamos National Laboratory have been developing electrochemical procedures for the decontamination of bare and painted metal objects. These methods have been found to be effective on highly corroded as well as relatively new metals. This study has been successful in decontaminating projectiles and shrapnel excavated during environmental restoration projects after 40+ years of exposure to the elements. Heavily corroded augers used in sampling activities throughout the area were also successfully decontaminated. This process has demonstrated its effectiveness and offers several advantages over the present metal decontamination practices of media blasting and chemical solvents. These advantages include the addition of no toxic or hazardous chemicals, low operating temperature and pressure, and easily scaleable equipment. It is in their future plans to use this process in the decontamination of gloveboxes destined for disposal as TRU waste

Low Impact Development for Industrial Areas

Science.gov (United States)

2015-07-01

copper gutters can also be significant sources of metal pollutants. Other studies indicate that vehicle disc brake pads and car tires can be a...industrial areas to develop the performance criteria for LID systems that specifically targeted these areas. Areas targeted include scrap metal recycling

Induction hardening of tool steel for heavily loaded aircraft engine components

Directory of Open Access Journals (Sweden)

Rokicki P.

2017-03-01

Full Text Available Induction hardening is an innovative process allowing modification of the materials surface with more effective, cheaper and more reproducible way to compare with conventional hardening methods used in the aerospace industry. Unfortunately, high requirements and strict regulation concerning this branch of the industry force deep research allowing to obtain results that would be used for numerical modelling of the process. Only by this way one is able to start the industrial application of the process. The main scope of presented paper are results concerning investigation of microstructure evolution of tool steel after single-frequency induction hardening process. The specimens that aim in representing final industrial products (as heavily loaded gears, were heat- -treated with induction method and subjected to metallographic preparation, after which complex microstructure investigation was performed. The results obtained within the research will be a basis for numerical modelling of the process of induction hardening with potential to be introduced for the aviation industrial components.

The World Health Organization and the Pharmaceutical Industry. Common areas of interest and differing views.

Science.gov (United States)

Hardwicke, Caroline J

2002-01-01

No article published in the scientific press in the last 10 years reviews the various areas of interest common to the World Health Organization (WHO) and the pharmaceutical industry. Despite a vast amount of information in the public domain, the policies expound the views only of the bodies they represent rather than comparing differing views. An understanding of the factors which affect the interaction between these organisations as well as the organisational structures and the actual areas of intersecting interest, may help to find ways for the industry to assist the WHO in its endeavours in developing countries. Modern drug development is performed initially in and for western society, leaving the areas of infectious or tropical diseases with relatively less industry investment than cancer and cardiovascular disorders. Aspects of the development of an ethical drug, regardless of its therapeutic class (selection of drug name, intellectual property rights, drug safety, marketing and pricing, quality assurance and counterfeiting, generic use, emerging drug donations) are influenced to varying degrees by the triad of money, politics and medical need and the perspectives (each defensible) placed thereon by the WHO and industry. Instead of simply defending their positions combining the best of these strategies to optimise drug development for the needs of developing countries appears logical. Similarly, via its philanthropic initiatives, industry will have donated over $US1 billion in drug and research aid in the period 1995 to 2005. These charitable projects should yield useful information for planning and organising future aid efforts. Global warming, only recently given serious governmental consideration, is an area not yet addressed in drug development policy although along with geographical effects, it is likely to have an impact on the epidemiology of diseases e.g. malaria returning to the Mediterranean, worldwide. With changing disease patterns (and

An association between air pollution and daily outpatient visits for respiratory disease in a heavy industry area.

Science.gov (United States)

Wang, Kuo-Ying; Chau, Tang-Tat

2013-01-01

In this work we used daily outpatient data from the Landseed Hospital in a heavily industrial area in northern Taiwan to study the associations between daily outpatient visits and air pollution in the context of a heavily polluted atmospheric environment in Chung-Li area during the period 2007-2011. We test the normality of each data set, control for the confounding factors, and calculate correlation coefficient between the outpatient visits and air pollution and meteorology, and use multiple linear regression analysis to seek significance of these associations. Our results show that temperature and relative humidity tend to be negatively associated with respiratory diseases. NO and [Formula: see text] are two main air pollutants that are positively associated with respiratory diseases, followed by [Formula: see text], [Formula: see text], [Formula: see text], CO, and [Formula: see text]. Young outpatients (age 0-15 years) are most sensitive to changing air pollution and meteorology factors, followed by the eldest (age [Formula: see text]66 years) and age 16-65 years of outpatients. Outpatients for COPD diseases are most sensitive to air pollution and meteorology factors, followed by allergic rhinitis, asthma, and pneumonia diseases. In the context of sex difference to air pollution and meteorological factors, male outpatients are more sensitive than female outpatients in the 16-65 age groups, while female outpatients are more sensitive than male outpatients in the young 0-15 age groups and in the eldest age groups. In total, female outpatients are more sensitive to air pollution and meteorological factors than male outpatients.

An association between air pollution and daily outpatient visits for respiratory disease in a heavy industry area.

Directory of Open Access Journals (Sweden)

Kuo-Ying Wang

Full Text Available In this work we used daily outpatient data from the Landseed Hospital in a heavily industrial area in northern Taiwan to study the associations between daily outpatient visits and air pollution in the context of a heavily polluted atmospheric environment in Chung-Li area during the period 2007-2011. We test the normality of each data set, control for the confounding factors, and calculate correlation coefficient between the outpatient visits and air pollution and meteorology, and use multiple linear regression analysis to seek significance of these associations. Our results show that temperature and relative humidity tend to be negatively associated with respiratory diseases. NO and [Formula: see text] are two main air pollutants that are positively associated with respiratory diseases, followed by [Formula: see text], [Formula: see text], [Formula: see text], CO, and [Formula: see text]. Young outpatients (age 0-15 years are most sensitive to changing air pollution and meteorology factors, followed by the eldest (age [Formula: see text]66 years and age 16-65 years of outpatients. Outpatients for COPD diseases are most sensitive to air pollution and meteorology factors, followed by allergic rhinitis, asthma, and pneumonia diseases. In the context of sex difference to air pollution and meteorological factors, male outpatients are more sensitive than female outpatients in the 16-65 age groups, while female outpatients are more sensitive than male outpatients in the young 0-15 age groups and in the eldest age groups. In total, female outpatients are more sensitive to air pollution and meteorological factors than male outpatients.

a Study of Oxygen Precipitation in Heavily Doped Silicon.

Science.gov (United States)

Graupner, Robert Kurt

Gettering of impurities with oxygen precipitates is widely used during the fabrication of semiconductors to improve the performance and yield of the devices. Since the effectiveness of the gettering process is largely dependent on the initial interstitial oxygen concentration, accurate measurements of this parameter are of considerable importance. Measurements of interstitial oxygen following thermal cycles are required for development of semiconductor fabrication processes and for research into the mechanisms of oxygen precipitate nucleation and growth. Efforts by industrial associations have led to the development of standard procedures for the measurement of interstitial oxygen in wafers. However practical oxygen measurements often do not satisfy the requirements of such standard procedures. An additional difficulty arises when the silicon wafer has a low resitivity (high dopant concentration). In such cases the infrared light used for the measurement is severely attenuated by the electrons of holes introduced by the dopant. Since such wafers are the substrates used for the production of widely used epitaxial wafers, this measurement problem is economically important. Alternative methods such as Secondary Ion Mass Spectroscopy or Gas Fusion Analysis have been developed to measure oxygen in these cases. However, neither of these methods is capable of distinguishing interstitial oxygen from precipitated oxygen as required for precipitation studies. In addition to the commercial interest in heavily doped silicon substrates, they are also of interest for research into the role of point defects in nucleation and precipitation processes. Despite considerable research effort, there is still disagreement concerning the type of point defect and its role in semiconductor processes. Studies of changes in the interstitial oxygen concentration of heavily doped and lightly doped silicon wafers could help clarify the role of point defects in oxygen nucleation and precipitation

Governing multi-actor decision processes in Dutch industrial area redevelopment

NARCIS (Netherlands)

Blokhuis, E.G.J.

2010-01-01

In the first part of the thesis, a literature review is presented. In this literature review, industrial areas in the Netherlands are discussed, leading to the conclusion that industrial areas are important for realizing sustainable economic growth in the Netherlands. Industrial areas play an

Resilience of chemical industrial areas through attenuation-based security

International Nuclear Information System (INIS)

Reniers, G.L.L.; Sörensen, K.; Khan, F.; Amyotte, P.

2014-01-01

This paper investigates the possibility of attenuation-based security within chemical industrial areas. Representing chemical industrial areas as mathematical networks, we prove by case-study that the resilience to disaster of such areas may follow a power-law distribution. Furthermore, we examine what happens to the network when highly hazardous installations would be intelligently protected against malicious acts: the network disintegrates into separate smaller networks. Hence, islands are formed with no escalation danger in between. We conclude that it is possible to protect chemical industrial areas in such a way that they are more resilient against terrorism

Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas; Sistema de avaliacao de desempenho em radioprotecao das industrias convencionais brasileiras nas areas de medidores nucleares e radiografia industrial

Energy Technology Data Exchange (ETDEWEB)

Santos, Joyra Amaral dos

1999-08-01

This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

A sustainable approach for industrial area redevelopment in the Netherlands

NARCIS (Netherlands)

Blokhuis, E.G.J.; Schaefer, W.F.; Kungolos, A.; Brebbia, C.A.; Beriatos, E.

2007-01-01

According to the Dutch Ministry of Economic Affairs, creating space for industrial areas is necessary to realize a sustainable economic growth. Currently, the average time needed to redevelop an industrial area in the Netherlands is 10 years. Furthermore, almost 30% of the Dutch stock of industrial

Assessment of sediment quality based on acid-volatile sulfide and simultaneously extracted metals in heavily industrialized area of Asaluyeh, Persian Gulf: concentrations, spatial distributions, and sediment bioavailability/toxicity.

Science.gov (United States)

Arfaeinia, Hossein; Nabipour, Iraj; Ostovar, Afshin; Asadgol, Zahra; Abuee, Ehsan; Keshtkar, Mozhgan; Dobaradaran, Sina

2016-05-01

Sediment samples from the coastal area of Asaluyeh harbor were collected during autumn and spring 2015. The acid-volatile sulfide (AVS) and simultaneously extracted metals (SEMs) were measured to assess the sediment quality and potential ecological risks. The average concentrations (and relative standard deviation (RSD)) of AVS in the industrial sediments were 12.32 μmol/g (36.91) and 6.34 μmol/g (80.05) in autumn and spring, respectively, while in the urban area, these values were 0.44 μmol/g (123.50) and 0.31 μmol/g (160.0) in autumn and spring, respectively. The average concentrations of SEM (and RSD) in the industrial sediments were 15.02 μmol/g (14.38) and 12.34 μmol/g (20.65) in autumn and spring, respectively, while in the urban area, these values were 1.10 μmol/g (43.03) and 1.06 μmol/g (55.59) in autumn and spring, respectively. Zn was the predominant component (34.25-86.24 %) of SEM, while the corresponding value for Cd, much more toxic ingredient, was less than 1 %. Some of the coastal sediments in the harbor of Asaluyeh (20 and 47 % in autumn and spring, respectively) had expected adverse biological effects based on the suggested criterion by United States Environmental Protection Agency (USEPA), while most stations (80 and 53 % in autumn and spring, respectively) had uncertain adverse effects.

Site survey for large wind turbines in the Rijnmond area. Plaatsingsmogelijkheden grote windturbines in het Rijnmondgebied

Energy Technology Data Exchange (ETDEWEB)

Arkesteyn, L A; Van der Ham, P

1985-01-01

This paper reveals only preliminary results of a study on site selection for large wind turbines in a heavily industrialized and urbanized area of The Netherlands: the Rijnmond area. Factors like average wind speed, coupling to electric power grid, acquisition of land, noise pollution, safety aspects, avoiding harm to birds, and fitting in the existent physical structure of the area are evaluated.

Air pollution around the Keihin heavy chemical industrial zone, and living environment and health injury in the inhabitants therein

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, I

1975-08-01

A survey of air pollution levels and the health of high school pupils and their parents was conducted in a heavily industrialized area of Kawasaki, Japan. The concentration of sulfur oxides in 1974 was about half of that in 1970 (0.029 ppM). The concentration of nitrogen oxides ranged from 0.030 to 0.040 ppM. There was a correlation between the concentrations of oxides of sulfur nitrogen. According to questionnaires, about 32 percent of the inhabitants showed concern about air pollution and photochemical smog. About 22 percent of the inhabitants complained of symptoms such as cold, rhinitis, and pharyngitis; and there was a correlation between total subjective symptoms and concentration of sulfur oxides. Near roadsides the concentration of nitrogen oxides was very high. Green plants are gradually disappearing from the heavily polluted area. Further industrialization in this area appears to be very dangerous for man and other living things.

Improvement of industrial efficiency by knowledge management in maintenance engineering

Directory of Open Access Journals (Sweden)

Carlos Alberto Mariotoni

2015-09-01

Full Text Available This article shows research and studies dealing with the management of knowledge in industrial maintenance engineering, developed in the field of applied research in real industrial companies of Europe, which are the consequences of  having knowledge on islands, as well as measures improvements when there is an adequate knowledge management. The peculiarities which are given in the maintenance of the company departments, knowledge of operators and technicians operating in these areas, is heavily based on their experiences (strong tacit component, what is difficult to measure and articulate, and however, on numerous occasions, this break from the knowledge, can impose a high cost for the industry.

Comparative multielement analyses of airborne particulate samples collected in various areas

International Nuclear Information System (INIS)

Mamuro, Tetsuo; Matsuda, Yatsuka; Mizohata, Akira

1973-01-01

In order to grasp the characteristic features of the air pollution by particulates in various areas in Japan, multielement analyses by instrumental neutron activation analysis and radioisotope energy dispersive X-ray fluorescence analysis were applied to 31 airborne particulate samples collected in 15 different areas, and the analytical results obtained were compared with one another. All the samples were collected by so-called ''10 micron cut'' samplers, the collection efficiency of which is considered to be 50% at 8μ and nearly zero beyond 10μ. Among the areas in question there are clean seaside areas, heavily industrialized areas, small cities along the Inland Sea or the Pacific Ocean around which industrialization is progressing, a small city having only a big iron work, an area famous for its ceramic industry and so on. The atmospheres over them were found to be quite different not only in pollution extent but also in pollution pattern. (auth.)

Distributions, sources and pollution status of 17 trace metal/metalloids in the street dust of a heavily industrialized city of central China

International Nuclear Information System (INIS)

Li, Zhonggen; Feng, Xinbin; Li, Guanghui; Bi, Xiangyang; Zhu, Jianming; Qin, Haibo; Dai, Zhihui; Liu, Jinling; Li, Qiuhua; Sun, Guangyi

2013-01-01

A series of representative street dust samples were collected from a heavily industrialized city, Zhuzhou, in central China, with the aim to investigate the spatial distribution and pollution status of 17 trace metal/metalloid elements. Concentrations of twelve elements (Pb, Zn, Cu, Cd, Hg, As, Sb, In, Bi, Tl, Ag and Ga) were distinctly amplified by atmospheric deposition resulting from a large scale Pb/Zn smelter located in the northwest fringe of the city, and followed a declining trend towards the city center. Three metals (W, Mo and Co) were enriched in samples very close to a hard alloy manufacturing plant, while Ni and Cr appeared to derive predominantly from natural sources. Other industries and traffic had neglectable effects on the accumulation of observed elements. Cd, In, Zn, Ag and Pb were the five metal/metalloids with highest pollution levels and the northwestern part of city is especially affected by heavy metal pollution. -- Highlights: •Large-scale Pb/Zn smelters contributed to elevated trace elements in the street dust. •The hard alloy processing caused the enrichment of a few elements. •Cd, In, Zn, Ag and Pb were the most polluted elements. •Northwestern Zhuzhou suffered severe contamination for a range of trace elements. -- Pb/Zn smelting and hard alloy processing operations have caused seriously contamination of trace metal/metalloids in the street dust

E-COMMERCE AREA FOR TEXTILE INDUSTRY

OpenAIRE

R. M. Aileni; D. Farima; M. Ciocoiu

2011-01-01

This paper presents some management aspects concerning the e-commerce area for textile industry.Here it can have database management – customers, products and brand visualisation management. The databasemanagement can be doing by using a database management system. For database management it was use therelational model based on first-order predicate logic [1]. In this paper it was analyzed the relational databasemodel. The e-commerce area is born from need to simplify the buying and selling g...

Environmental impact of industrial wastes on marine area, case study: Port Sudan coastal area

International Nuclear Information System (INIS)

Abdalrahman, E. A. H.

2004-05-01

This study was carried out to determine the effect of the industrial wastes on marine environment in Port Sudan area. A very intensive study has been made to identify types of pollutions drained in seawater at study area of Red Sea coast. Samples were taken from three stations (1, 2 and 3) at study area and the following analysis were made: Temperature, salinity, hydrogen ion concentration, dissolved oxygen, biochemical oxygen demand, nutrient, oil and grease. The laboratory results revealed that wastes pollute the marine environment as the cooling water from studied industries which is drain into the seawater increases the degree of temperature approximately from 6 to 12 C degree above the allowed rate, the matter which was adverse effect on the environment and living marine creatures due to the sudden change of temperature degree. Also, it was found that the great amount of oil spills discharged into seawater due to many factors such as: cooling water, oil spills from ships and loading and discharging operations of crude oil ships. Accordingly these oils spills might have a deadly effect on living marine creatures, which have been mention in details through out this research. Hence, and to minimize this adverse effect of industrial wastes and others on the marine environment, may recommend to the following: Pretreatment to the industrial wastes should be taking before its draining into the Red Sea coastal area. Surveillance all ships into the port and observing loading and discharging operations as well as those ships in the regional waters and implementing the international maritime laws. Enlightenment the industrial administrators and manpower working with them about the severity which will definitely cause the marine environmental deterioration as a result of industrial wastes. To punish every one who violates the laws of environment protection. Thus, can be safeguarding the environment from pollutions and consequently develop the natural resources and proceed

Radiation protection program of Petrobras in industrial radiography area

International Nuclear Information System (INIS)

Signorini, M.

1988-01-01

Industrial hygiene has as main purpose the preservation of employees physical integrity when exposed to certain agressive agents. PETROBRAS Industrial hygiene program forecasts preventive policies in several specific fields. For the ionizing radiations area it was developed the ''Radiologic Protection Program'' which also deals with specific actions in industrial radiography jobs. These actions are hereinafter presented. (C.M.) [pt

The refinery industry within the Mediterranean area

International Nuclear Information System (INIS)

1999-01-01

During the period 1997-1998 Ome (Observatorie Mediterraneen de l'Energie) within a working group which was formed by the experts among the associated companies, has carried on an analysis on the prospects of refinery industry in the Mediterranean area in view of 2010. The aim of this study was to make clear, to the different operators, the consequences of the political choices in investments on refinery industry in the context of the progressive liberalization of the sector [it

Understanding inter-industry wage structures in the euro area

OpenAIRE

Genre, Véronique; Momferatou, Daphne; Kohn, Karsten

2009-01-01

This paper focuses on the euro area wage structure and its potential determinants from a sectoral viewpoint. Merging information from the OECD Structural Analysis database with data from the EU Labour Force Survey, we construct a cross-country panel of 22 industries in 8 euro area countries for 1991-2002. Data inspection confirms the existence of a fairly stable inter- industry wage structure that is similar across countries. We then apply panel data techniques to identify factors explaining ...

Chemical industrial areas and their dynamic danger behaviour

NARCIS (Netherlands)

Reniers, Genserik L L; Audenaert, Amaryllis; Dullaert, W.; Soudan, K.

2007-01-01

Chemical industrial areas or so-called chemical clusters consist of various companies situated next to each other. Such areas are composed of hundreds of chemical installations exhibiting danger to a certain degree for initiating or continuing knock-on effects. In this paper, a methodology to model

ANALYSIS OF INVESTMENT ATTRACTIVENESS REDEVELOPMENT PROJECTS THE INDUSTRIAL AREAS IN KIEV

Directory of Open Access Journals (Sweden)

Yevsyukov T. O.

2017-08-01

Full Text Available At the present stage of development of land relations in major cities of our country important issue is the development of investment, attract and use foreign investment. According to the Law of Ukraine "On investment activity" under the investment necessary to understand "all types of property and intellectual values invested in business and other activities, which resulted in creating profit (income or social effect is achieved." For the economy of any city, including the city. Kyiv and development of urban land use, renovation of industrial areas deindustrialization of inefficient production centers, it is extremely important investment activity (foreign investment as one of the most effective mechanisms for the development and activities of national companies. The purpose of the article to analyze the investment attractiveness of the redevelopment projects of industrial areas to economic development of eco-industrial land use in Kiev, despite the downward trend in investment activity of domestic enterprises, the need for technical and technological modernization of production as well as the entire market infrastructure, redevelopment of industrial areas. Redevelopment areas – this is a comprehensive activity aimed at changing the existing construction work carried out with the help of large investments (investments in reconstruction; renovation of; overhaul; demolition; conversion; improving the environment, which results in a positive effect on economic, social and environmental aspects. Investment and construction projects related to redevelopment of industrial land use (objects in the management of the city, characterized by considerable risks given the high capital intensity, binding to a specific area, and the impact of other internal and external factors. That is why this investment activity should be ensured exceptional dynamic management to ensure the quality of implementation and the necessary level of profitability and

Analysis of Risk Optimization on the Industrial Area Around

International Nuclear Information System (INIS)

Sony, DT; Demon-Handoyo

2000-01-01

Indonesia as an industrial country, there are large industrial area whichis directly or indirectly have an effect to human health by routine dischargeof waste from industrial installations. So, the criteria limit must bedetermined to regulate industrial area. The PRA method (Probabilistic RiskAssessment) is used in the nuclear technology especially reactor safetytechnology could be applied to accommodate those problems. The principles ofPRA method is to determine probability and consequences for accident ofindustrial plant or transportation of product. The analysis procedureincludes classification of industry activity type and inventories, estimationof external consequences, estimation of probability for installation andtransportation accident, determination of social risk and prioritization ofrisks. Calculation of consequence is based on the lost of life which isaffected by fire, toxic and explosive. The calculation for one industrialarea simple model as case study was done. From the calculation result, theconsequences value of 0 - 25 persons/event; 26 - 50 persons/event; 51 - 75persons/event, 625 - 650 persons/event and the event probability value of1.10 -2 to 3.10 -8 are obtained. The optimization value of industrial areaaround can be determined by using combination of probability value andconsequences value. (author)

[Pollution-ecological problems of old industrial and mining areas and future research prospects].

Science.gov (United States)

Zhou, Qixing

2005-06-01

Environmental pollution and its solicitation in ecological problems of old industrial and mining areas have become a worldwide technological puzzle restricting sustainable economic and social development. But, the definition and category of old industrial and mining areas is still disputed as an important concept. In this paper, the concept of old industrial and mining area was discussed in theory, and, proceeded with analyzing the complexity of current situation and environmental pollution problems of old industrial and mining areas in China, more keystone attention was paid to the secondary pollution problems from old industrial and mining areas as an important frontier of science. On the basis of expounding the complexity and characters of environmental pollution in old industrial and mining areas, it was suggested that as two key scientific problems in environmental sciences and ecology, the formation mechanisms and control technology of secondary pollution in old industrial and mining areas and the responses of new-type diseases to environmental pollution based on molecular ecotoxicology should be systematically studied on the national scale, and be an important component of environmental protection strategy in China in the future.

Evaluating the suitability of different environmental samples for tracing atmospheric pollution in industrial areas.

Science.gov (United States)

Francová, Anna; Chrastný, Vladislav; Šillerová, Hana; Vítková, Martina; Kocourková, Jana; Komárek, Michael

2017-01-01

Samples of lichens, snow and particulate matter (PM 10 , 24 h) are used for the source identification of air pollution in the heavily industrialized region of Ostrava, Upper Silesia, Czech Republic. An integrated approach that uses different environmental samples for metal concentration and Pb isotope analyses was applied. The broad range of isotope ratios in the samples indicates a combination of different pollution sources, the strongest among them being the metallurgical industry, bituminous coal combustion and traffic. Snow samples are proven as the most relevant indicator for tracing metal(loid)s and recent local contamination in the atmosphere. Lichens can be successfully used as tracers of the long-term activity of local and remote sources of contamination. The combination of PM 10 with snow can provide very useful information for evaluation of current pollution sources. Copyright © 2016 Elsevier Ltd. All rights reserved.

Solid waste management in Khartoum industrial area

International Nuclear Information System (INIS)

Elsidig, N. O. A.

2004-05-01

This study was conducted in Khartoum industrial area (KIA). The study discusses solid waste generation issues in KIA as well as solid waste collection, storage, transport and final disposal methods. A focus on environmental impact resulting from the accumulation of solid waste was presented by reviewing solid waste management in developed as well as developing countries starting from generation to final disposal. Environmental health legislation in Sudan was investigated. The study covers all the (eight) industrial sub-sectors presented in KIA. The main objective of the study is to assess the situation of solid waste in KIA. To fulfill the objectives of the study the researcher deemed it necessary to explore problems related to solid waste generation and solid waste arrangement with special emphasis on final disposal methods. Practically, 31 (thirty-one) factories representing the different industrial sub-sectors in KIA were studied. This represents 25% of the total number of factories located in KIA. Data were obtained by, questionnaires, interviews and observations mainly directed to concerned officials, solid waste workers, pickers and brokers. Obtained data were stored, coded, tabulated and analyzed using the computer systems (excel and SPSS programmes). The obtained results should clear deficiency in the management of solid waste which led to great environmental deterioration in KIA and neighboring residential areas. The environment in studied area is continuously polluted due to high pollution loads and unproved solid waste management. In order to maintain health environment operating factories have to pretreated their solid waste according to the recognized standards and waste minimization techniques such as recycling and re use should be widely applied, moreover, running crash programme for environmental sanitation in Khartoum state should be expanded and improved to include special characteristics of solid waste from industries. Finally, increase awareness

Climate Variability and Industrial-Suburban Heat Environment in a Mediterranean Area

Directory of Open Access Journals (Sweden)

Giuseppina A. Giorgio

2017-05-01

Full Text Available The Urban Heat Island (UHI phenomenon prevalently concerns industrialized countries. It consists of a significant increase in temperatures, especially in industrialized and urbanized areas, in particular, during extreme warm periods like summer. This paper explores the climate variability of temperatures in two stations located in Matera city (Southern Italy, evaluating the increase in temperatures from 1988 to 2015. Moreover, the Corine Land Covers (1990–2000–2006–2012 were used in order to investigate the effect of land use on temperatures. The results obtained confirm the prevalence of UHI phenomena for industrialized areas, highlighting the proposal that the spreading of settlements may further drive these effects on the microclimate. In particular, the presence of industrial structures, even in rural areas, shows a clear increase in summer maximum temperatures. This does not occur in the period before 2000, probably due to the absence of the industrial settlement. On the contrary, from 2000 to 2015, changes are not relevant, but the maximum temperatures have always been higher than in the suburban area (station localized in green zone during daylight hours.

A general tool to construct case library for industrial area redevelopment

NARCIS (Netherlands)

Wang, T.; Jessurun, Joran; Han, Q.; de Vries, B.

2015-01-01

Abandoned industrial area redevelopment is of great importance for regional sustainability. However it is difficult to decide how one industrial area can be redeveloped because of the complexity involved, including but not limited to, expectation from various stakeholders, large amount of investment

A study about the prevalence and the related factors of metabolic syndrome and fatty liver comparing the urban area to tbe industrial area

Energy Technology Data Exchange (ETDEWEB)

Jeong, Hyo Eun; Cho, Pyong Kon [Dept. of of Radiological Science, Catholic University of Daegu. Daegu (Korea, Republic of)

2016-09-15

As the tertiary industry is being developed, many problems are introduced in an industrial area in Korea. This study aims to investigate the residents' health conditions, such as the prevalence of metabolic syndrome and fatty liver diagnosed by ultrasonography, comparing the urban with the industrial areas. The subjects were 378 adults in the urban area and 376 adults in the industrial area. Subject variables accounted for were gender, age, drinking habits, smoking habits, physical activities, waist circumferences and BMI. In blood tests, fasting blood glucose, triglyceride, HDL, blood pressures, total cholesterol, AST, ALT and GGT were examined. Also, the presence and absence of fatty liver, diagnosed using ultrasonography, was investigated. As a result, the prevalence of metabolic syndrome were 43.7% in the urban area and 51.6% in the industrial area, hence it was significantly higher in the industrial area than in the urban area. Fasting blood glucose, triglyceride and waist circumference in the distribution of the individual components were 47.4, 53.7, and 16.1% in the urban area and 54.5, 61.5, and 22.9% in the industrial area respectively, so it was substantially higher in the industrial area than in the urban area. On the other hand, HDL, diastolic blood pressure, and fatty liver were 25.7, 43.4, and 44.7% in the urban area and 21.3, 19.9, and 36.7% in the industrial area respectively and thus it was much higher in the urban area than in the industrial area. In conclusion, this study shows that there were significant differences between the residents' health condition, comparing the urban area to the industrial area. Therefore, the precaution and aggressive management of metabolic syndrome may be necessary, in accordance with the characteristics of the industrial zone.

A study about the prevalence and the related factors of metabolic syndrome and fatty liver comparing the urban area to tbe industrial area

International Nuclear Information System (INIS)

Jeong, Hyo Eun; Cho, Pyong Kon

2016-01-01

As the tertiary industry is being developed, many problems are introduced in an industrial area in Korea. This study aims to investigate the residents' health conditions, such as the prevalence of metabolic syndrome and fatty liver diagnosed by ultrasonography, comparing the urban with the industrial areas. The subjects were 378 adults in the urban area and 376 adults in the industrial area. Subject variables accounted for were gender, age, drinking habits, smoking habits, physical activities, waist circumferences and BMI. In blood tests, fasting blood glucose, triglyceride, HDL, blood pressures, total cholesterol, AST, ALT and GGT were examined. Also, the presence and absence of fatty liver, diagnosed using ultrasonography, was investigated. As a result, the prevalence of metabolic syndrome were 43.7% in the urban area and 51.6% in the industrial area, hence it was significantly higher in the industrial area than in the urban area. Fasting blood glucose, triglyceride and waist circumference in the distribution of the individual components were 47.4, 53.7, and 16.1% in the urban area and 54.5, 61.5, and 22.9% in the industrial area respectively, so it was substantially higher in the industrial area than in the urban area. On the other hand, HDL, diastolic blood pressure, and fatty liver were 25.7, 43.4, and 44.7% in the urban area and 21.3, 19.9, and 36.7% in the industrial area respectively and thus it was much higher in the urban area than in the industrial area. In conclusion, this study shows that there were significant differences between the residents' health condition, comparing the urban area to the industrial area. Therefore, the precaution and aggressive management of metabolic syndrome may be necessary, in accordance with the characteristics of the industrial zone

Chemical composition of sewage sludge of domestic and industrial areas of Hyderabad

International Nuclear Information System (INIS)

Ansari, T.P.; Kazi, T.G.; Kazi, G.H.

2001-01-01

A study on chemical composition sewage sludge of domestic and industrial areas of Hyderabad city has been carried out. The sludge samples were collected from various domestic and industrial areas of Hyderabad, over a period of 3 months. Analysis of sludge samples for different micro-nutrients and toxic elements has been accomplished by reliable analytical methods using atomic absorption, UV and colorimeter. It is observed that the levels of copper, nickel, zinc, lead and cadmium are higher in sludge samples of industrial area than those of domestic areas of Hyderabad. (author)

Management of industrial sites and areas contaminated by radionuclides in France

International Nuclear Information System (INIS)

Oudiz, A.; Rousseau, D.

2001-01-01

The presentation involves two parts making mention on the one hand on the industrial sites management and on the other hand on contaminated areas management. In a third part, are considered the analogies and the differences susceptible of appearing in the management modes of industrial sites and areas. (N.C.)

assessment of atmospheric metal depositions in the industrial areas

African Journals Online (AJOL)

Osondu

and Ogun states house many industries which are assumed to have impacted the states. It is in ... southwest Nigeria were assessed to determine the extent of air pollution of these areas. ... of pollutants but are expensive and risks of ... Island) served as the Control site for Lagos ..... cement industry on accumulation of heavy.

A Study on regeneration cases with industrial Heritage in mining areas of Korea

Science.gov (United States)

Cho, Seungyeoun; Ji, Sangwoo; Yim, Giljae

2017-04-01

The mining areas have to face urban decline problem in population and aging after its closing. Many mines were shut down due to changes in industrial structure through 20 century. Central and local governments has been trying to solve urban decline of abandoned mine areas by enacting special acts or introducing support programs for decades. In the year of 1995, South Korean government also enacted "Special act on the assistance to the development of abandoned mine areas" to promote the economy of abandoned mine areas that is depressed following the decline of the coal industry and to help balanced regional development and to improve the living standard of the residents in such abandoned mine areas. Local authorities has been trying to revitalize the regional economy by attracting tourism industry under the financial support and deregulation by this special law. With this background, this study analysis 13 regeneration cases which are utilizing the industrial heritage of the abandoned area in S. Korea. Despite the importance of mining, negative images of abandon mine have been engraved due to environmental destruction. Most of abandoned mines were left without any action since its closing. Early stage of abandoned mine area regeneration, such as Sabuk, Munkyong, are focusing on adjacent land not on abandoned mine. Abandoned mines were restored its original state and theme park including hotels, casinos and other tourist facilities were developed on adjacent land. Eco-trails on some granite caves such as Jungsun were opened to the public as natural resources not industrial heritage. The industrial heritage was very restricted to making museums about history of mining industry. However, there has been a significant change in perception toward reusing industrial heritage for urban regeneration in recent years. From the viewpoint of urban regeneration, abandon mine areas and its facilities are receiving attention as important regional assets as industrial heritage to

EU energy policies achievement by industries in decentralized areas

Science.gov (United States)

Destro, Nicola; Stoppato, Anna; Benato, Alberto; Schiro, Fabio

2017-11-01

Energy Roadmap outlined by the European Commission sets out several routes for a more sustainable, competitive and secure energy system in 2050. All the outlined scenarios consider energy efficiency, renewable energy, nuclear energy and carbon capture and storage. In this paper, more attention has been devoted to the energy efficiency issue, by the identification of new micro and small networks opportunity fed by hybrid plants in the North-East of Italy. National energy balance and national transmission system operator data allowed to collect industrial energy consumptions data on the investigated area. Applying industrial statistics to the local energy needs allows to collect a dataset including consumption information by factory and by company structure (size and employees) for each industrial sector highlighting the factory density in the area. Preliminary outcomes from the model address to the exploitation of local by-product for energy purposes.

Heat pump applications in utility centres for large industrial areas in the Netherlands

NARCIS (Netherlands)

Wit, J.B. de

1999-01-01

A grand design for industrial waste heat utilisation has been composed in Rijnmond Industrial Area, the largest (petrochemical) industrial area in The Netherlands. In combination with local CHP plants, an HP, MP and LP steam exchange system has been developed. The primary energy savings of this

A multi-attribute Systemic Risk Index for comparing and prioritizing chemical industrial areas

International Nuclear Information System (INIS)

Reniers, G.L.L.; Sörensen, K.; Dullaert, W.

2012-01-01

Measures taken to decrease interdependent risks within chemical industrial areas should be based on quantitative data from a holistic (cluster-based) point of view. Therefore, this paper examines the typology of networks representing industrial areas to formulate recommendations to more effectively protect a chemical cluster against existing systemic risks. Chemical industrial areas are modeled as two distinct complex networks and are prioritized by computing two sub-indices with respect to existing systemic safety and security risks (using Domino Danger Units) and supply chain risks (using units from an ordinal expert scale). Subsequently, a Systemic Risk Index for the industrial area is determined employing the Borda algorithm, whereby the systemic risk index considers both a safety and security network risk index and a supply chain network risk index. The developed method allows decreasing systemic risks within chemical industrial areas from a holistic (inter-organizational and/or inter-cluster) perspective. An illustrative example is given.

Exporting Australia's remote area power supply industry

International Nuclear Information System (INIS)

Presnell, K.

2001-01-01

The Australian renewable energy industry has two faces: Remote Area Power Supply systems (RAPS), where the trade-off is between the traditional diesel generator and diesel hybrid or the stand alone renewable energy system. The competency of the Australian RAPS industry is recognised internationally. Grid connected renewable energy technologies, where industry activity is expanding rapidly, but where Australian competencies carry relatively little weight internationally (other than for research and development of related components such as big performance, crystalline silicon photovoltaic cells). Individual industry development strategies are required in each instance. The focus of this paper is on strategies that enhance the export potential of the Australian RAPS industry. Involvement of the electricity supply utilities is promoted as a means of quickly instituting a substantial industry presence. The term RAPS can be confusing. It is used to describe any supply system serving a remote user, be they a single property owner with a simple, stand alone DC photovoltaic supply, or several communities with complex, inter-connected, diesel/hybrid power stations, sometimes termed a 'remote-grid'. Utility interest tends to emerge as market fragmentation decreases, system complexity increases and economies of scale become evident. A review of the domestic situation is a necessary adjunct to development of export strategies for Australian RAPS products. The two are inexorably linked, as is reflected in the format of this paper. (author)

Study on waste waters of metal finishing industries around Lahore metropolitan area

International Nuclear Information System (INIS)

Khan, Izhar-ul-Haq; Mahmood, F.; Tufail, S.; Naeem, M.

2002-01-01

Study was undertaken on the waste water samples from metal finishing industries of Lahore metropolitan area for the evaluation of metallic impurities. The metal finishing industry was classified into three categories i. e. medium scale, small scale and cottage scale industry. About 93 wastewater samples were collected from various metal finishing industries around Lahore metropolitan area. In addition to toxic elements like cadmium, nickel and zinc the other parameters such as hydrogen ion concentration (pH), Electrical conductivity (EC) and Total Dissolved Salts (TDS) were also determined. (author)

Cross-industry Collaborations in the Convergence Area of Functional Foods

NARCIS (Netherlands)

Bornkessel, S.; Broring, Stefanie; Omta, S.W.F.

2016-01-01

Convergence processes are based on the activity of distinct industry sectors showing crossindustry
collaborations. The aim of this paper is to analyze cross-industry collaborations between
the food and pharmaceutical sectors in the convergence area of functional foods. Selected
companies

EU energy policies achievement by industries in decentralized areas

Directory of Open Access Journals (Sweden)

Destro Nicola

2017-01-01

Full Text Available Energy Roadmap outlined by the European Commission sets out several routes for a more sustainable, competitive and secure energy system in 2050. All the outlined scenarios consider energy efficiency, renewable energy, nuclear energy and carbon capture and storage. In this paper, more attention has been devoted to the energy efficiency issue, by the identification of new micro and small networks opportunity fed by hybrid plants in the North-East of Italy. National energy balance and national transmission system operator data allowed to collect industrial energy consumptions data on the investigated area. Applying industrial statistics to the local energy needs allows to collect a dataset including consumption information by factory and by company structure (size and employees for each industrial sector highlighting the factory density in the area. Preliminary outcomes from the model address to the exploitation of local by-product for energy purposes.

Composition of airborne particulate matter in the industrial area versus mountain area

Directory of Open Access Journals (Sweden)

Barbora Sýkorová

2016-03-01

Full Text Available The paper deals with research of air pollution in two different locations on the Moravian-Silesian Region, Czech Republic. These are the sites Ostrava-Radvanice, which is located in the area affected by the industry and Ostravice in the mountains (without significant effect of the industry. The dust particles collected at these locations were subjected to a wide range of analyses. The mass concentration, the mass-size distribution, mineralogical composition, the concentration of PAHs (polycyclic aromatic hydrocarbons, and the concentrations of selected metals (Cd, Pb, Zn, Fe, Mn, As, Ni, Co, and Cr were observed at the particulate matter.

Assessment of industrial minerals and rocks in the controlled area

International Nuclear Information System (INIS)

Castor, S.B.; Lock, D.E.

1996-01-01

Yucca Mountain in Nye County, Nevada, is a potential site for a permanent repository for high-level nuclear waste in Miocene ash flow tuff. The Yucca Mountain controlled area occupies approximately 98 km 2 that includes the potential repository site. The Yucca Mountain controlled area is located within the southwestern Nevada volcanic field, a large area of Miocene volcanism that includes at least four major calderas or cauldrons. It is sited on a remnant of a Neogene volcanic plateau that was centered around the Timber Mountain caldera complex. The Yucca Mountain region contains many occurrences of valuable or potentially valuable industrial minerals, including deposits with past or current production of construction aggregate, borate minerals, clay, building stone, fluorspar, silicate, and zeolites. The existence of these deposits in the region and the occurrence of certain mineral materials at Yucca Mountain, indicate that the controlled area may have potential for industrial mineral and rock deposits. Consideration of the industrial mineral potential within the Yucca Mountain controlled area is mainly based on petrographic and lithologic studies of samples from drill holes in Yucca Mountain. Clay minerals, zeolites, fluorite, and barite, as minerals that are produced economically in Nevada, have been identified in samples from drill holes in Yucca Mountain

Assessment of industrial minerals and rocks in the controlled area

Energy Technology Data Exchange (ETDEWEB)

Castor, S.B. [Nevada Bureau of Mines and Geology, Reno, NV (United States); Lock, D.E. [Mackay School of Mines, Reno, NV (United States)

1996-08-01

Yucca Mountain in Nye County, Nevada, is a potential site for a permanent repository for high-level nuclear waste in Miocene ash flow tuff. The Yucca Mountain controlled area occupies approximately 98 km{sup 2} that includes the potential repository site. The Yucca Mountain controlled area is located within the southwestern Nevada volcanic field, a large area of Miocene volcanism that includes at least four major calderas or cauldrons. It is sited on a remnant of a Neogene volcanic plateau that was centered around the Timber Mountain caldera complex. The Yucca Mountain region contains many occurrences of valuable or potentially valuable industrial minerals, including deposits with past or current production of construction aggregate, borate minerals, clay, building stone, fluorspar, silicate, and zeolites. The existence of these deposits in the region and the occurrence of certain mineral materials at Yucca Mountain, indicate that the controlled area may have potential for industrial mineral and rock deposits. Consideration of the industrial mineral potential within the Yucca Mountain controlled area is mainly based on petrographic and lithologic studies of samples from drill holes in Yucca Mountain. Clay minerals, zeolites, fluorite, and barite, as minerals that are produced economically in Nevada, have been identified in samples from drill holes in Yucca Mountain.

Health Impacts of Air Pollution around Major Industrial Areas

Directory of Open Access Journals (Sweden)

Mathilde Pascal

2013-01-01

Full Text Available We performed a literature review to investigate how epidemiological studies have been used to assess the health consequences of living in the vicinity of industries. 77 papers on the chronic effects of air pollution around major industrial areas were reviewed. Major health themes were cancers (27 studies, morbidity (25 studies, mortality (7 studies, and birth outcome (7 studies. Only 3 studies investigated mental health. While studies were available from many different countries, a majority of papers came from the United Kingdom, Italy, and Spain. Several studies were motivated by concerns from the population or by previous observations of an overincidence of cases. Geographical ecological designs were largely used for studying cancer and mortality, including statistical designs to quantify a relationship between health indicators and exposure. Morbidity was frequently investigated through cross-sectional surveys on the respiratory health of children. Few multicenter studies were performed. In a majority of papers, exposed areas were defined based on the distance to the industry and were located from 20 km from the plants. Improving the exposure assessment would be an asset to future studies. Criteria to include industries in multicenter studies should be defined.

Bringing fiber to the home to rural areas in Denmark

DEFF Research Database (Denmark)

Pedersen, Jens Myrup; Riaz, M. Tahir

2009-01-01

In order to support development of rural areas, and avoid that these  areas are being depopulated, access to fast broadband networks can contribute by facilitating tele working, distance learning, ICT for industries and farming etc. In this paper we show how broadband and Fiber To The Home (FTTH......) is developing in Denmark, and that FTTH is also being deployed in rural areas. A main reason for this is that consumer-owed utility companies have decided to invest heavily in the field, to a large extent with the philosophy that, since all consumers are a part of the investment, everybody should also benefit...

Further considerations for damping in heavily insulated pipe systems

International Nuclear Information System (INIS)

Anderson, M.J.; Lindquist, M.R.; Severud, L.K.

1985-01-01

Over the past several years a body of test data has been accumulated which demonstrates that damping in small diameter heavily insulated pipe systems is much larger than presently recommended by Regulatory Guide 1.61. This data is generally based on pipe systems using a stand-off insulation design with a heater annulus. Additional tests have how been completed on similar pipe systems using a strap-on insulation design without the heater annulus. Results indicate some reduction in damping over the stand-off designs. Test data has also been obtained on a larger sixteen-inch diameter heavily insulated pipe system. Results of these two additional test series are presented. Revised damping values for seismic design of heavily insulated pipe systems are then recommended

Further considerations for damping in heavily insulated pipe systems

International Nuclear Information System (INIS)

Anderson, M.J.; Lindquist, M.R.; Severud, L.K.

1985-01-01

Over the past several years a body of test data has been accumulated which demonstrates that damping in small diameter heavily insulated pipe systems is much larger than presently recommended by Regulatory Code 1.61. This data is generally based on pipe systems using a stand-off insulation design with a heater annulus. Additional tests have now been completed on similar pipe systems using a strap-on insulation design without the heater annulus. Results indicate some reduction in damping over the stand-off designs. Test data has also been obtained on a larger sixteen-inch diameter heavily insulated pipe system. Results of these two additional test series are presented. Revised damping values for seismic design for heavily insulated pipe systems are then recommended

Precautionary interventions in industrial areas. An optimal stopping approach

Energy Technology Data Exchange (ETDEWEB)

Pauwels, N

2001-04-01

The contribution consists of an abstract of a PhD thesis. The thesis deals with the precautionary evacuation of an industrial facility's workforce threatened by a radiological release from a nuclear power plant nearby. The issue of deferring intervention decisions until additional information is available is addressed. Furthermore, interventions in industrial areas with a concentration of chemical and petrochemical plants form part of this study.

Precautionary interventions in industrial areas. An optimal stopping approach

International Nuclear Information System (INIS)

Pauwels, N.

2001-01-01

The contribution consists of an abstract of a PhD thesis. The thesis deals with the precautionary evacuation of an industrial facility's workforce threatened by a radiological release from a nuclear power plant nearby. The issue of deferring intervention decisions until additional information is available is addressed. Furthermore, interventions in industrial areas with a concentration of chemical and petrochemical plants form part of this study

Analysis of soil samples from Gebeng area using NAA technique

Science.gov (United States)

Elias, Md Suhaimi; Wo, Yii Mei; Hamzah, Mohd Suhaimi; Shukor, Shakirah Abd; Rahman, Shamsiah Ab; Salim, Nazaratul Ashifa Abdullah; Azman, Muhamad Azfar; Hashim, Azian

2017-01-01

Rapid development and urbanization will increase number of residence and industrial area. Without proper management and control of pollution, these will give an adverse effect to environment and human life. The objective of this study to identify and quantify key contaminants into the environment of the Gebeng area as a result of industrial and human activities. Gebeng area was gazetted as one of the industrial estate in Pahang state. Assessment of elemental pollution in soil of Gebeng area base on level of concentration, enrichment factor and geo-accumulation index. The enrichment factors (EFs) were determined by the elemental rationing method, whilst the geo-accumulation index (Igeo) by comparing of current to continental crustal average concentration of element. Twenty-seven of soil samples were collected from Gebeng area. Soil samples were analysed by using Neutron Activation Analyses (NAA) technique. The obtained data showed higher concentration of iron (Fe) due to abundance in soil compared to other elements. The results of enrichment factor showed that Gebeng area have enrich with elements of As, Br, Hf, Sb, Th and U. Base on the geo-accumulation index (Igeo) classification, the soil quality of Gebeng area can be classified as class 0, (uncontaminated) to Class 3, (moderately to heavily contaminated).

Reconstructing historical trends in metal input in heavily-disturbed, contaminated estuaries: studies from Bilbao, Southampton Water and Sicily

International Nuclear Information System (INIS)

Cundy, A.B.; Croudace, I.W.; Cearreta, A.; Irabien, M.J.

2003-01-01

Estuaries may be important reservoirs for contaminants as they tend to act as sinks for fine, contaminant-reactive sediments, and, historically, they have acted as centres for industrial and urban development. Analysis of dated sediment cores from these areas may allow historical trends in heavy metal input to be reconstructed, and recent and historical inputs of metal contaminants to be compared. Undisturbed saltmarsh settings have been used widely in the reconstruction of historical trends in metal input as saltmarshes provide a stable, vegetated substrate of dominantly fine sediments, and are less prone to erosion and reworking than adjacent mudflat areas. In comparison, much less research on historical pollution trends has been undertaken at estuarine sites which are prone to severe local disturbance, such as intertidal areas which are routinely dredged or where sedimentary processes have been modified by human activities such as shipping, salt working, port activities, land claim etc. This paper assesses the usefulness of 210 Pb and 137 Cs dating, combined with geochemical studies, in reconstructing historical trends in heavy metal input and sediment accretion in 3 heavily-modified, industrialised estuarine areas in Europe: the Bilbao estuary (Spain), Southampton Water (UK), and the Mulinello estuary (Sicily). Of these sites, only a salt marsh core from the Mulinello estuary provides a high-resolution record of recent heavy metal inputs. In Southampton Water only a partial record of changing metal inputs over time is retained due to land-claim and possible early-diagenetic remobilisation, while at Bilbao the vertical distribution of heavy metals in intertidal flats is mainly controlled by input on reworked sediment particles and variations in sediment composition. Where 137 Cs and 210 Pb distributions with depth allow a chronology of sediment deposition to be established, and early-diagenetic remobilisation has been minimal, mudflat and saltmarsh cores from

Creating new path for Old Industrial Areas: A Case Study on Dalian city, China

Directory of Open Access Journals (Sweden)

Yimei Yin and Zhigao Liu

2012-01-01

Full Text Available The formation of new industries has recently been widely studied, but little research attention has been paid to the formation of new industries in old industrial districts, especially in transitional countries such as China. Based on fieldwork and rereading historical archives, this paper uses an example of Dalian tourism cluster to contribute to understanding the emergence of new economy in old industrial areas in a transitional country. The Section 2 of this paper will provide the theoretical framework from evolutionary economics for my empirical study. In Section 3, this paper will discuss the main characteristics of the decline of old industrial areas in Northeast China and the significances of developing new economy to revitalizing old industry areas. Section 4 will introduce the transitional history of Dalian economy from a high industrial region to a new economy city and also provides descriptive information about the development process of Dalian tourism industry. In Section 5, this paper will probe into the dynamics of the Dalian tourism cluster, from viewpoints of co-evolution and co-adaptation of firm, technology and institutions. Finally, we will give some policy suggestions of how to foster and promote new industries in old industrial areas, especially for transitional countries.

Superconductivity in heavily boron-doped silicon carbide

Directory of Open Access Journals (Sweden)

Markus Kriener, Takahiro Muranaka, Junya Kato, Zhi-An Ren, Jun Akimitsu and Yoshiteru Maeno

2008-01-01

Full Text Available The discoveries of superconductivity in heavily boron-doped diamond in 2004 and silicon in 2006 have renewed the interest in the superconducting state of semiconductors. Charge-carrier doping of wide-gap semiconductors leads to a metallic phase from which upon further doping superconductivity can emerge. Recently, we discovered superconductivity in a closely related system: heavily boron-doped silicon carbide. The sample used for that study consisted of cubic and hexagonal SiC phase fractions and hence this led to the question which of them participated in the superconductivity. Here we studied a hexagonal SiC sample, free from cubic SiC phase by means of x-ray diffraction, resistivity, and ac susceptibility.

Characteristic of ambient airborne and respirable particulate around a non formal industrial area

International Nuclear Information System (INIS)

Muhayatun Santoso; Diah Dwiana Lestiani; Mariana Marselina; Rita Mukhtar

2016-01-01

Characterization of airborne particulate matter and respirable particulate in Parung Panjang district especially on surrounding non formal used batteries industrial area has been carried out to follow up the previous results with respect to high concentrations of lead detected in Serpong area. Sampling of airborne particulate matter in Parung Panjang was conducted using Gent stacked filter unit sampler, while the respirable particulate matter samples collected using personal dust sampler in Parung Panjang as a non formal Industrial area and Sukarasa village as a control, during 2011-2012. The concentration of masses were determined gravimetrically, while for elemental concentrations by X-Ray based methods. The average of mass concentration of air ambient PM 2.5 and PM 10 in Parung Panjang were 27.3 ± 13.7 and 77.5 ± 17.1 μg.m -3 , respectively. While the average concentration of respirable particulate in non formal industrial and control areas were 260 ± 233 and 82 ± 38 μg.m -3 , respectively. The percentage of average Pb concentration in PM 2.5 and PM 2.5-10 were contribute up to 45 and 10 % of the mass concentration, respectively. The maximum percentage concentration of Pb in respirable particulate in industrial and control area were 12.11 and 0.27 %, respectively. These results showed that the Pb concentrations in respirable particulate in industrial area were significantly tens times higher than in the control area. The high concentration of Pb in Parung Panjang was the main key element came from the used lead battery industry and one of pollutant source that contributed to the Pb pollution in Serpong area. (author)

Vegetation pattern and soil characteristics of the polluted industrial area of Karachi

International Nuclear Information System (INIS)

Kabir, M.; Iqbal, M.Z.; Farooqi, M.Z.; Shafiq, M.

2010-01-01

A quantitative phyto sociological survey was conducted around the industrial areas of Sindh Industrial Trading Estate (S.I.T.E.) of Karachi. The herbaceous, shrubs vegetation was predominantly disturbed in nature. Fifteen plant communities based on Importance Value Index (IVI) of species were recognized. Eighty plant species were recorded in industrial areas. Abutilon fruticosum L., attained the highest importance value index (823.25) followed by Prosopis juliflora DC. (662.62), Corchorus trilocularis L. (467.20), Aerva javanica Burm.f. (419.97), Amaranthus viridis L. (397.65) and Senna holosericea L. (387.22), respectively. P. juliflora and A. fruticosum showed leading first dominant in five and four stands, respectively. Whereas, A. javanica, A. viridis, S. holosericea, Launaea nudicaulis L., Crochorus depressus L. and Salvadora L., attained the presence class III. Zygophyllum simplex L., Suaeda fruticosa L., Convolvulus glomeratus Choisky, Cressa cretica L., Cleome viscosa L., Calotropis procera Willd, Blepharis sindica T. Anderson, Rhynchosia pulverulenta L., Abutilon pakistanicum Jafri and Ali, Chenopodium album L., Capparis decidua Forssk and Digera muricata L. Mart showed the presence of class II. Whereas, rest of 58 species showed presence of class I. The soil characteristics of the polluted industrial area were also analyzed and related with the vegetation of the polluted areas. The Industrial area soil was coarse in texture and ranged from sandy clay loam to sandy loam. The soil was acidic to alkaline in nature. Maximum water holding capacity, bulk density, porosity, CaCO/sub 3/, pH, organic matter, total organic carbon, chloride, electrical conductivity, total dissolved salt, available sulphur contents, exchangeable sodium and potassium were recorded in wide range. It was concluded that certain edaphic factors due to industrial activities and induction of pollutants were responsible for variation in vegetation composition of the study area. (author)

Cytogenetic abnormalities of the descendants of permanent residents of heavily contaminated East Kazakhstan.

Science.gov (United States)

Chaizhunusova, Nailya; Madiyeva, Madina; Tanaka, Kimio; Hoshi, Masaharu; Kawano, Noriyuki; Noso, Yoshihiro; Takeichi, Nobuo; Rakhypbekov, Tolebay; Urazalina, Nailya; Dovgal, Galina; Rymbaeva, Tamara; Tokanova, Sholpan; Beisengazina, Meruert; Kembayeva, Kulypash; Inoue, Ken

2017-11-01

More than 400 nuclear explosion tests were conducted at the Semipalatinsk Nuclear Test Site (SNTS) and significant radioactive substances were released. The long-term consequences of the activities at the SNTS and the appearance of any hereditary effects remain insufficiently studied about 25 years after the test site was closed. The population living in villages near the SNTS are considered to have been heavily exposed to external and internal radiation. This study aims to perform an assessment and comprehensive cytogenetic analysis of the inhabitants living near the SNTS, and their first-(F1) and second-(F2) generation children. Residents of the East Kazakhstan region living in the area covered by the former SNTS were included in the study. To evaluate the hereditary effects of nuclear testing, comprehensive chromosome analyses were performed in lymphocytes using conventional Giemsa and fluorescent in situ hybridization methods in 115 F1 and F2 descendants in the villages of Dolon and Sarzhal, which were heavily contaminated. The parents of the subjects had permanently lived in the villages. A higher number of stable-type chromosome aberrations such as translocations was found in these residents than in 80 residents of the control area, Kokpecty, which indicates the possibility that radiation had biological effects on the exposed subjects.

Fire protection requirements of the insurance industry and their impact on nuclear power plant design and construction

International Nuclear Information System (INIS)

Deitchman, J.V.; King, W.T. Jr.; Nashman, T.A.

1976-01-01

The insurance industry, with its wealth of knowledge and experience in the fire protection area and with preservation of its funds at stake, has always been heavily involved in the fire protection programs of nuclear power plants. Since it was concerned with property preservation in addition to nuclear safety, the insurance industry placed more detailed emphasis on fire protection requirements than did the nuclear regulatory bodies. Since the Browns Ferry fire, however, the insurance industry, the Nuclear Regulatory Commission, the Advisory Committee on Reactor Safeguards and the utilities themselves have re-examined their approaches to fire protection. A more coordinated approach seems to have emerged, which is based largely upon insurance industry specifications and guidelines. The paper briefly summarizes the fire protection requirements of the insurance industry as they apply to nuclear power plants. Some of the ways these requirements affect project planning, plant design, and construction timing are reviewed, as well as some of the more controversial fire protection areas

Wind energy in industrial areas. Results of an attitude survey

International Nuclear Information System (INIS)

Schoolderman, J.A.; Huiberts, R.G.J.

2000-06-01

The feasibility of installing wind turbines in industrial parks in the Netherlands has been investigated. An overview is given of possibilities and constraints to fit in wind turbines in industrial areas, based on the results of a literature study, a market consultation of sectoral organizations, representatives of local industrial circles and industrial experts in the field of renewable energy. Also a telephone survey was carried out among 130 entrepreneurs in the Netherlands to determine their attitudes towards the use of sustainable energy and wind energy in industrial parks. The results of the attitude study are published in this report. The main report is a separate report for which a separate abstract has been prepared. The intermediate results were discussed at a meeting (23 February 2000), in which representatives from the industry, provinces, municipalities and the government participated

Environmental and Socio-economic Aspects of the Operation of Industrial Regions: The Case Study of the Industrial Area of Alexandroupolis (Greece)

International Nuclear Information System (INIS)

Theofanoudi, Aglaia; Diakaki, Christina; Katsivela, Eleftheria

2009-01-01

The paper summarizes the results of a study concerning the operation of industrial plants and their effects to the environment. It also addresses, shortly, the consequences to the quality of human life and proposes potential measures that may contribute to the reduction of the negative environmental impacts. The relatively small organized Industrial Area of Alexandroupolis (Greece) is examined as a case study. In particular, the activities of its major industrial facilities are presented and their emissions to the environment are examined. In addition, the socio-economic aspects of the operation of the Industrial Area are studied. The results of the study showed that the operation of the Industrial Area has specific negative effects in the natural environment of the region and in the quality of life of the residents. Methodological and legislative tools, such as control systems for the environmental pollution, the green chemistry, and the environmental management systems, may be employed to assist the prevention and confrontation of environmental problems

THE NEED FOR FUNCTION PLATFORMS IN ENGINEER TO ORDER INDUSTRIES

NARCIS (Netherlands)

Alblas, Alex; Wortmann, Hans; Bergendahl, MN; Grimheden, M; Leifer, L; Skogstad, P; Cantamessa, M

2009-01-01

Many industries base their innovations on product platforms. Platforms have predefined modularity with standardized interfaces. However, product platforms provide significant challenges to engineering industries that rely heavily on R&D, such as microlithography systems. Developing these systems

Determination of elemental in soil samples from Gebeng area using NAA technique

International Nuclear Information System (INIS)

Md Suhaimi Elias; Wo, Y.M.; Mohd Suhaimi Hamzah

2016-01-01

Rapid development and urbanization will increase number of residence and industrial area. Without proper management and control of pollution, these will give an adverse effect to environment and human life. The objective of this study to identify and quantify key contaminants into the environment of the Gebeng area as a result of industrial and human activities. Gebeng area was gazetted as one of the industrial estate in Pahang state. Assessment of elemental pollution in soil of Gebeng area base on level of concentration, enrichment factor and geo-accumulation index. The enrichment factors (EFs) were determined by the elemental rationing method, whilst the geo-accumulation index (I_g_e_o) by comparing of current to continental crustal average concentration of element. Twenty-seven of soil samples were collected from Gebeng area. Soil samples were analysed by using Neutron Activation Analyses (NAA) technique. The obtained data showed higher concentration of iron (Fe) due to abundance in soil compared to other elements. The results of enrichment factor showed that Gebeng area have enrich with elements of As, Br, Hf, Sb, Th and U. Base on the geo-accumulation index (I_g_e_o) classification, the soil quality of Gebeng area can be classified as class 0, (uncontaminated) to Class 3, (moderately to heavily contaminated). (author)

Bio-monitoring of the most industrialized area in Poland: Trees' response to climate and anthropogenic environmental changes

Science.gov (United States)

Sensuła, Barbara; Wilczyński, Sławomir; Piotrowska, Natalia

2017-04-01

Silesia is one of the regions with the highest levels of air pollution in Europe, highly industrialized over the years and highly populated. In this study, trees (Pinus Sylvestris L.)growing in the heavily urbanized area in close proximity to point-source pollution emitters, such as a heat and power plant, nitrogen plant, and steelworks in Silesia (Poland), were analyzed as bio-indicators of contemporary environmental changes. Trees are a very good archive of ecosystem changes, becouse they are sensitive to climate changes and anthropogenic pollution. The pollution impacts human, plants and animal life and different ecosystem processes. The changes in the ecosystem can disturb the metabolism and physiological processes of trees, and consequently, they also have an effect on the wood structure, tree ring width and the isotopic composition of wood and its components. The analysed samples covered the time period of the development of industrialization and the modernization in the industrial sector in Poland. In Poland, the systematic long-term monitoring of air pollutants is generally restricted to rural point-source regions in urban areas. Even for those areas, air pollution emissions were not continually monitored and data is only available for the last decades. Tree ring series that present long-term data can be used to analyse the ecosystem changes, caused by human activities. The conifers investigated in this study have grown for many years under the stress of environmental contamination. We analysed the spatiotemporal distribution of growth reductions, the depth of reduction with respect to the distance from the emitter, the relationship between tree growth and radiocarbon and stable isotope composition and climate during the industry development period and during pro-ecological strategy application. Pines chronologies indicate that trees have a similar sensitivity to most climatic elements of the previous and given year, but there is also observed a different

The Haendeloe area in Norrkoeping, Sweden: Does it fit for Industrial Symbiosis development?

Energy Technology Data Exchange (ETDEWEB)

Hatefipour, Saeid; Baas, Leenard; Eklund, Mats (Div. of Environmental Technology and Management - Dept. of Management and Engineering, Linkoeping Univ., Linkoeping (Sweden)), e-mail: saeid.hatefipour@liu.se

2011-06-15

Today, sustainable cities/regions are playing an important role in sustainable development projects. The overall aim of the current paper is to demonstrate an Industrial Symbiosis development in the Haendeloe area of Norrkoeping city in the Oestergoetland county of Sweden. It is part of a research program called 'Sustainable Norrkoeping' focusing on developing links between the industrial and the urban part of the city. As analysis of the current situation is important for understanding the future development, the paper tries to map the current industrial symbiosis links and symbiotic network to identify potentials exist. To achieve this, paper gives a general view of how this area has been developed, constructed, and grown. The next stage is devoted to an inventory of different actors, stakeholders, and companies, their processes and relationships in the form of energy, materials and by-products exchanges, flows and streams into and out of the Haendeloe area considering the Haendeloe/Norrkoeping as system boundaries. In addition, by describing different tools, elements and approaches of industrial symbiosis and considering and applying two main key tools as industrial inventories and input/output matching the paper also tries to show that whether the already industrial activities formed inside the Haendeloe fits for an industrial symbiosis development

Heavy metal contamination in the vicinity of an industrial area near Bucharest.

Science.gov (United States)

Velea, Teodor; Gherghe, Liliana; Predica, Vasile; Krebs, Rolf

2009-08-01

Heavy metals such as lead are well known to cause harmful health effects. Especially children are particularly susceptible to increased levels of lead in their blood. It is also a fact that lead concentration is increasing in the environment due to increased anthropogenic activity. The risk of heavy metal contamination is pronounced in the environment adjacent to large industrial complexes. In a combined case study, the environmental pollution by heavy metals was related to children's health in the vicinity of an industrial area located 4 km south-east from Bucharest about 2 km east from the nearest town-Pantelimon. This site includes companies processing different, nonferrous solid wastes for recovery of heavy metals and producing different nonferrous alloys and lead batteries. In this paper, mainly the results of environmental sampling and analyses are summarized. Water, soil, and atmospheric deposition samples were collected from different locations within 3 km from the industrial area. For comparison, samples were also taken from Bucharest. Water samples were filtered (open collecting pots were used on nine different sites between August and November 2006. At most sampling locations, the heavy metal concentrations in soil decrease with increasing distance to the presumably major source of pollution. Highest heavy metal concentrations were found in 10-20 cm soil depths. There were also decreasing heavy metal concentrations for atmospheric deposition with increasing distance to the industrial site. In surface and groundwater samples, traces of zinc, copper and lead were detected. The heavy metal concentrations in soil were increased in the study area, mostly under legal action limits in low-concern areas (e.g., 1,000 mg Pb/kg dry soil), but often above action limits for high-concern areas (100 mg Pb/kg dry soil) such as populated areas. The soluble lead concentrations in water samples indicate a need for monitoring and assessing water quality in more detail. The

Assessment of the Impact of Industrial Effluents on Groundwater Quality in Okhla Industrial Area, New Delhi, India

Directory of Open Access Journals (Sweden)

Wequar Ahmad Siddiqui

2009-01-01

Full Text Available In the present study physicochemical parameters like pH, hardness, TDS, chloride, sulphate, nitrate, fluoride, DO, COD and conductivity of some important heavy metals such as iron, cobalt, cadmium, lead, mercury, chromium, selenium and arsenic were first analyzed in effluent water of Okhla industrial area phase-II and then groundwater of near by areas. Obtained values of effluent water were compared with ISI standard for effluent water discharge and groundwater values were compared with ISI and WHO drinking water standards. The result shows that discharge of untreated effluents by the industries is leading to contamination of groundwater of the surrounding areas. Lead, mercury, fluoride, TDS, sulphate was above the desirable limit in effluent water (ISI standard for effluent water discharge. Subsequent analysis of groundwater of nearby areas was rated as unacceptable for drinking because of presence of fluoride in all the samples above the desirable limit. Lead, mercury, cadmium, chloride was also detected in many samples.

Impact of Industrial Releases on Inshas Area

International Nuclear Information System (INIS)

El-Messiry, A.M.; Aly, M.M.

1999-01-01

Two Egyptian research reactors are located within the nuclear research center at Inshas area, 30 km north east of Cairo. This area are crowded by different industrial plants. The releases from them has a hazardous and economical effects on the research center workers and the surrounding inhabitancy. In the present work we study these effects. A meteorological regional specific data is considered all over the year, including a wind rose characterization. The study considered both normal operating conditions and an accidental releases. The results shows that there are a considerable risk due to normal releases in some areas downwind direction of the major releases, and a highly risk in areas subjected to major exposure. Regional maps of emission distribution, economical damage , pollutant concentration are obtained. The study helps to identify solutions to problems of atmospheric protection. It can be used as a decision support for the environmental, economic, and innovation planning at the national levels taking into consideration the national pollution standards and variety of existing emission sources

Comparison on mechanical properties of heavily phosphorus- and arsenic-doped Czochralski silicon wafers

Science.gov (United States)

Yuan, Kang; Sun, Yuxin; Lu, Yunhao; Liang, Xingbo; Tian, Daxi; Ma, Xiangyang; Yang, Deren

2018-04-01

Heavily phosphorus (P)- and arsenic (As)-doped Czochralski silicon (CZ-Si) wafers generally act as the substrates for the epitaxial silicon wafers used to fabricate power and communication devices. The mechanical properties of such two kinds of n-type heavily doped CZ silicon wafers are vital to ensure the quality of epitaxial silicon wafers and the manufacturing yields of devices. In this work, the mechanical properties including the hardness, Young's modulus, indentation fracture toughness and the resistance to dislocation motion have been comparatively investigated for heavily P- and As-doped CZ-Si wafers. It is found that heavily P-doped CZ-Si possesses somewhat higher hardness, lower Young's modulus, larger indentation fracture toughness and stronger resistance to dislocation motion than heavily As-doped CZ-Si. The mechanisms underlying this finding have been tentatively elucidated by considering the differences in the doping effects of P and As in silicon.

The effect of industrial vehicles on the road’s level of service of industrial area in Malang City

Science.gov (United States)

Agustin, I. W.; Sumantri, Y.

2017-06-01

Malang was a great city that has the characteristics of diverse industries and it was spread in each district. Industry was one of the activities that have the characteristics of the movement with the goal of shipping and distribution. The vehicles used are large vehicles such as trucks and trailers. Problems related to the road’s performance that is the emergence of several points of delay and congestion due to the movement and the volume of vehicles as well as the limited capacity of existing roads. It encourages researchers to do research related to the effect of the industrial vehicle movements on the performance of existing roads in the city of Malang. The main purpose of the research is to analyze the effect of industrial vehicles movement on the road’s level of service of industrial area and to find out alternative solutions to improve the road’s level of service of industrial area. The research used multiple linear regression and do something analysis. The results showed that the types of industry in the city of Malang are ILMETTA, IATT, Agrokim, Sentra and Large Industries. Determining the location of the main observation based on the distribution of industry, have a major impact directly on the street, and the class of the national road are located in Sunandar Priyo Sudarmo Street. Existing land use in Sunandar Priyo Sudarmo Street are industrial, healthcare, office and it dominated by trade and services. Related to the variables that affect the movement of industrial vehicles are the number of employees (X3) and the delivery frequency (X6). The road’s level of service of Sunandar Priyo Sudarmo Street are D and E. While the effect of industrial vehicles movement on the road’s level of service which ranged from 13.77 per cent to 22.13 per cent of the total volume of vehicles on the road. Some referrals will be used to handle the problems that the road widening and the selection of alternative routes for the industrial vehicles.

ASEAN free-trade area and its implications on the battery industry

Science.gov (United States)

Garrucho, Peter D., Jr.

1994-02-01

In February, 1992, the six ASEAN member nations agreed to reduce tariffs and thus, eventually, to create an ASEAN Free Trade Area (AFTA) over 15 years. AFTA will lead to more competition in the high-growth ASEAN battery domestic market. Already about ten companies from four countries export both to markets that are rigorous in quality (e.g., the USA and Australia) and to heavily discounted markets, e.g., the Middle East. To date, however, these manufacturers rarely sell to other ASEAN markets outside their home country. AFTA should also encourage manufacturers of battery equipment, mould making, separators, battery electricals, and testing equipment to locate their facilities in an ASEAN country. Technology and productivity is high and wages are reasonable in ASEAN nations and with AFTA, the markets are larger. Manufacturing complementation programmes will also become an attractive option.

In vitro and in vivo toxicities of sediment and surface water in an area near a major steel industry of Korea: endocrine disruption, reproduction, or survival effects combined with instrumental analysis.

Science.gov (United States)

Kim, Sunmi; Lee, Sangwoo; Kim, Cheolmin; Liu, Xiaoshan; Seo, Jihyun; Jung, Hyorin; Ji, Kyunghee; Hong, Seongjin; Park, Jinsoon; Khim, Jong Seong; Yoon, Seokmin; Lee, Woojin; Park, Jeongim; Choi, Kyungho

2014-02-01

The influence of industrial and/or municipal contaminant inputs on the aquatic environment of Pohang, Korea was investigated, with a focus on bioassay combined with instrumental analysis. Pohang is the most heavily populated city in Gyeongsangbuk-do province of Korea, with more than half a million residents, and also hosts the nation's biggest steel manufacturer and related industries. Sediment (n=15) and surface water samples (n=17) were collected from Hyeongsan River which runs across the Pohang city, in two separate events, i.e., June 2010 and February 2011. Sediment samples were first Soxhlet-extracted (raw extract) and were measured for estrogenicity using H295R cell line, and also analyzed for alkylphenols (APs), bisphenol A (BPA), PAHs, and PCBs. For sediment samples which exhibited greatest effects in the cell line, further fractionation was performed into non-polar, mid-polar, and polar portions. In surface water samples, heavy metals were also analyzed. Among 15 sediment samples, station S2 near the steel industry complex and station M3 near the municipal area showed the greatest sex hormone changes, and these changes were generally explained by the fractions which contained APs and BPA. Principal component analysis (PCA) however suggests that chemicals that were not analyzed in the present study would better explain endocrine disruption capacity of sediments. In water samples, adverse effects on hatchability and growth of Japanese medaka fish, and on Daphnia reproduction were noted following exposure to six water samples collected from stations near industrial and municipal areas. Several heavy metals and nonylphenol (NP) concentrations exceeded surface water quality guidelines, suggesting adverse effects of contamination inputs from both industrial and municipal activities. Observed estrogenicities in stations such as S2 and M3 warrant further investigations on longer term ecosystem impacts near industrial and municipal areas. The levels of major

Explosive phenomena in heavily irradiated NaCl

NARCIS (Netherlands)

denHartog, HW; Vainshtein, DI; Matthews, GE; Williams, RT

1997-01-01

In heavily irradiated NaCl crystals explosive phenomena can be initiated during irradiation or afterwards when samples are heated to temperatures between 100 and 250 degrees C. During irradiation of NaCl Na and Cl-2 precipitates and void structures are produced along with the accumulation of stored

Nuclear emergency planning and response in industrial areas. Results of a qualitative study in 9 industrial companies

International Nuclear Information System (INIS)

Pauwels, N.; Hardeman, F.; Soudan, K.

1998-11-01

Substantial economic losses and potential dangerous situations may result when industrial companies unexpectedly have to shut down their activities in an abrupt way. With respect to the industrial companies located in the Antwerp harbour region, the reason for such an unplanned shut-down could be the decision to (preventively) evacuate their workers, or to have them sheltered, in case of an alarm situation at a nearby nuclear power plant of Doel or in any other adjacent industrial factory. Between January and August 1998, the prevention advisors of nine industrial companies have been interviewed to gain insight in the scale and relative importance of several economic costs and practical difficulties that may arise. Moreover, the appropriateness of the existing nuclear emergency response decision structure and intervention philosophy was investigated. The main conclusions drawn from the interviews are reported. Recommendations are made to increase the efficiency of implementing countermeasures in industrial areas

Nuclear emergency planning and response in industrial areas. Results of a qualitative study in 9 industrial companies

Energy Technology Data Exchange (ETDEWEB)

Pauwels, N.; Hardeman, F.; Soudan, K

1998-11-01

Substantial economic losses and potential dangerous situations may result when industrial companies unexpectedly have to shut down their activities in an abrupt way. With respect to the industrial companies located in the Antwerp harbour region, the reason for such an unplanned shut-down could be the decision to (preventively) evacuate their workers, or to have them sheltered, in case of an alarm situation at a nearby nuclear power plant of Doel or in any other adjacent industrial factory. Between January and August 1998, the prevention advisors of nine industrial companies have been interviewed to gain insight in the scale and relative importance of several economic costs and practical difficulties that may arise. Moreover, the appropriateness of the existing nuclear emergency response decision structure and intervention philosophy was investigated. The main conclusions drawn from the interviews are reported. Recommendations are made to increase the efficiency of implementing countermeasures in industrial areas.

Growth and characterization of heavily doped silicon crystals

Energy Technology Data Exchange (ETDEWEB)

Scala, R.; Porrini, M. [MEMC Electronic Materials SpA, via Nazionale 59, 39012 Merano (Italy); Borionetti, G. [MEMC Electronic Materials SpA, viale Gherzi 31, Novara (Italy)

2011-08-15

Silicon crystals grown with the Czochralski method are still the most common material used for the production of electronic devices. In recent years, a growing need of large diameter crystals with increasingly higher doping levels is observed, especially to support the expanding market of discrete devices and its trend towards lower and lower resistivity levels for the silicon substrate. The growth of such heavily doped, large-diameter crystals poses several new challenges to the crystal grower, and the presence of a high dopant concentration in the crystal affects significantly its main properties, requiring also the development of dedicated characterization techniques. This paper illustrates the recent advances in the growth and characterization of silicon crystals heavily doped with antimony, arsenic, phosphorus and boron. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Long-term airborne contamination studied by attic dust in an industrial area: Ajka, Hungary

Science.gov (United States)

Völgyesi, P.; Jordan, G.; Szabo, Cs.

2012-04-01

Heavy industrial activities such as mining, metal industry, coal fired power plants have produced large amount of by-products and wide-spread pollution, particularly in the period of centrally dictated economy after WWII, in Hungary. Several studies suggest that significant amount of these pollutants have been deposited in the urban environment. Nowadays, more than half of the world's population is living in urban areas and people spend almost 80% of their lives indoors in developed countries increasing human health risk due to contamination present in urban dwellings. Attic dust sampling was applied to determine the long-term airborne contamination load in the industrial town of Ajka (Hungary). There has been a high industrial activity in Ajka since the end of the 19th century. In addition to aluminum and alumina industry, coal mining, coal fired power plant and glass industry sites, generated numerous waste heaps which act as multi-contamination sources in the area. In October 2010 the Ajka red mud tailings pond failed and caused an accidental regional contamination of international significance. The major objective of this research was to study and map the spatial distribution of heavy metal contamination in airborne attic dust samples. At 27 sampling sites 30 attic dust samples were collected. Sampling strategy followed a grid-based stratified random sampling design. In each cell a house for attic dust sample collection was selected that was located the closest to a randomly generated point in the grid cell. The project area covers a 8x8 grid of 1x1 km cells with a total area of 64 km2. In order to represent long-term industrial pollution, houses with attics kept intact for at least 30-40 years were selected for sampling. Sampling included the collection of background samples remotely placed from the industrialized urban area. The concentration of the major and toxic elements (Al, Ca, Fe, K, Mg, Mn, Na, P, S, and As, Ba, Cd, Co, Cr, Cu, Li, Mo, Ni, Pb, Se, Sn

Phthalates and alkylphenols in industrial and domestic effluents: case of Paris conurbation (France).

Science.gov (United States)

Bergé, A; Gasperi, J; Rocher, V; Gras, L; Coursimault, A; Moilleron, R

2014-08-01

Phthalates and alkylphenols are toxics classified as endocrine disrupting compounds (EDCs). They are of particular concern due to their ubiquity and generally higher levels found in the environment comparatively to other EDCs. Industrial and domestic discharges might affect the quality of receiving waters by discharging organic matter and contaminants through treated waters and combined sewer overflows. Historically, industrial discharges are often considered as the principal vector of pollution in urban areas. If this observation was true in the past for some contaminants, no current data are today available to compare the quality of industrial and domestic discharges as regards EDCs. In this context, a total of 45 domestic samples as well as 101 industrial samples were collected from different sites, including 14 residential and 33 industrial facilities. This study focuses more specifically on 4 phthalates and 2 alkylphenols, among the most commonly studied congeners. A particular attention was also given to routine wastewater quality parameters. For most substances, wastewaters from the different sites were heavily contaminated; they display concentrations up to 1200 μg/l for di-(2-ethylhexyl) phthalate and between 10 and 100 μg/l for diethyl phthalate and nonylphenol. Overall, for the majority of compounds, the industrial contribution to the flux of contaminant reaching the wastewater treatment plants ranges between 1 and 3%. The data generated during this work constitutes one of the first studies conducted in Europe on industrial fluxes for a variety of sectors of activity. The study of the wastewater contribution was used to better predict the industrial and domestic contributions at the scale of a huge conurbation heavily urbanized but with a weak industrial cover, illustrated by Paris. Our results indicate that specific investigations on domestic discharges are necessary in order to reduce the release of phthalates and alkylphenols in the sewer systems

Environmental exposure to arsenic and chromium in an industrial area

OpenAIRE

Vimercati, Luigi; Gatti, Maria F; Gagliardi, Tommaso; Cuccaro, Francesco; De Maria, Luigi; Caputi, Antonio; Quarato, Marco; Baldassarre, Antonio

2017-01-01

Arsenic and chromium are widespread environmental contaminants that affect global health due to their toxicity and carcinogenicity. To date, few studies have investigated exposure to arsenic and chromium in a population residing in a high-risk environmental area. The aim of this study is to evaluate the exposure to arsenic and chromium in the general population with no occupational exposure to these metals, resident in the industrial area of Taranto, Southern Italy, through biological monitor...

Long-term evaluation of the needle surface wax condition of Pinus sylvestris around different industries in Lithuania

International Nuclear Information System (INIS)

Kupcinskiene, Eugenija; Huttunen, Satu

2005-01-01

The aim of our study was to evaluate the annual dynamics of needle surface wax erosion and wettability in Scots pines exposed to a gradient of industrial pollutants emitted from the main factories of Lithuania: a nitrogen fertilizer factory, an oil refinery and a cement factory. Decreased emissions (in the case of the oil refinery and the cement factory) were reflected in the increased structural surface area (SSA, i.e. area covered by tubular waxes) on the needles. The nearly constant amount of emissions from the nitrogen fertilizer factory within the 1994-2000 period corresponded to negligible annual differences in SSA. Annual changes in the hydrophobicity of needles on the investigated transects were small. Despite the decreased pollution within the 7-year period, industrial emissions are still causing significantly accelerated wax erosion and increased wettability in needles sampled from the stands most heavily affected by pollutants. - Tubular wax on the pine needle surface reflects changes/differences in industrial emissions

Multivariate analysis of heavy metal contaminations in seawater and sediments from a heavily industrialized harbor in Southern Taiwan

International Nuclear Information System (INIS)

Lin, Yung-Chang; Chang-Chien, Guo-Ping; Chiang, Pen-Chi; Chen, Wei-Hsiang; Lin, Yuan-Chung

2013-01-01

Highlights: • Kaohsiung Harbor is the largest international commercial port in Taiwan. • The metal distributions in the seawater and sediments were investigated. • Many metals exhibited higher levels of enrichment inside the harbor. • Multivariate statistical analysis was used to characterize the metal pollutions. • Two complex arrays of contamination behaviors exist inside and outside the harbor. -- Abstract: Heavy metal pollution, including chromium, zinc, arsenic, cadmium, mercury, copper, lead, and aluminum, in the largest industrial harbor in southern Taiwan was investigated. Increasing metal contamination was observed by monitoring heavy metal concentrations in seawater and sediments and estimating the enrichment factors, particularly those inside the harbor. Compared to other metal-polluted harbors worldwide, the presence of chromium in the sediments was relatively high. Excluding the background contribution, the harbor area was polluted by outflows from river mouths, wastewater discharging pipes, and point sources near industrial activities within the harbor. It is shown by principal component and cluster analyses that metal contamination was affected by a wide range of different and complex contamination mechanisms inside and outside the harbor, suggesting managing the pollution using straightforward strategies, i.e., solutions that only consider a single source or single pathway of metal emissions, is problematic

The current state of taxation and regulation of land plot size of industrial areas in Ukraine

Directory of Open Access Journals (Sweden)

М.А. Malashevskyy

2016-04-01

Full Text Available An analysis of the domestic legal and regulatory framework for land taxation has been performed. The ratio of industry land within the land resources of Ukraine has been investigated. The legal basis for determination of land plot areas necessary for implementation of industrial activities has been considered. The legal regime of industry land has been investigated. The conclusion of the need for improvement of methods for determining excess areas for taxation purposes has been made and optimization of land use in populated areas.

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-01-01

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area. PMID:26580644

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas.

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-11-13

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area.

The ASEAN Free-Trade Area and its implications on the battery industry

International Nuclear Information System (INIS)

Garrucho, P.D. Jr.

1994-01-01

In February, 1992, the six ASEAN member nations agreed to reduce tariffs and thus, eventually, to create an ASEAN Free Trade Area (AFTA) over 15 years. AFTA will lead to more competition in the high-growth ASEAN battery domestic market. Already about ten companies from four countries export both to markets that are rigorous in quality (e.g., the USA and Australia) and to heavily discounted markets, e.g., the Middle East. To date, however, these manufacturers rarely sell to other Asean markets outside their home country. AFTA should also encourage manufacturers of battery equipment, mould making, separators, battery electricals, and testing equipment to locate their facilities in an Asean country. Technology and productivity is high and wages are reasonable in ASEAN nations and with AFTA, the markets are larger. Manufacturing complementation programmes will also become an attractive option. (orig.)

Eco-industrial zones in the context of sustainability development of urban areas.

Science.gov (United States)

Sacirovic, Selim; Ketin, Sonja; Vignjevic, Nada

2018-03-04

Industry is one of the main activities in the city and in many cities of the world, and the dominant industrial zones are the most significant morphological forms of concentration of industrial facilities in the city and are concentrated industrial and business activity. Industrial parks combine activities related to energy and resource consumption, emissions, waste generation, economic benefits, and regional development. The focus of this work is the path of transformation between the present and the vision of a sustainable city in the future. The problem and the subject of research related to two related objects of research: the city and sustainable development. In this paper, the co-author's industrial symbiosis parks, modern tendencies of the spatial distribution of productive activities, circular economy, to attract leading corporations and open the way for new ventures while preserving the living environment in an urban area.

Area Factor Determinations for an Industrial Worker Exposed to a Concrete Slab End-State

International Nuclear Information System (INIS)

Jannik, G. Timothy; Lee, Patricia L.; Farfan, Eduardo B.; Roach, Jesse L.

2008-01-01

The U.S. Department of Energy's (DOE) Savannah River Site (SRS) is decommissioning many of its excess facilities through removal of the facility structures leaving only the concrete-slab foundations in place. Site-specific, risk-based derived concentration guideline levels (DCGLs) for radionuclides have been determined for a future industrial worker potentially exposed to residual contamination on these concrete slabs as described in Jannik. These risk-based DCGLs were estimated for an exposure area of 100 m 2 . During deactivation and decommissioning (D and D) operations at SRS, the need for area factors for larger and smaller contaminated areas arose. This paper compares the area factors determined for an industrial worker exposed to a concrete slab end-state for several radionuclides of concern at SRS with 1) the illustrative area factors provided in MARSSIM, 2) the area correction factors provided in the U.S. Environmental Protection Agency's (EPA) Soil Screening Guidance, and 3) the hot spot criterion for field application provided in the RESRAD User's Manual. The purpose of this site-specific assessment is to determine if any of the recommended area factors provided in the guidance documents could be utilized at SRS for field applications of the industrial worker DCGLs. Results show the area factors that were determined for an SRS industrial worker exposed to concrete slab end-states for the common radionuclides provided in the referenced guidance documents. In addition to the SRS site-specific area factors, the following area factors are provided for comparison: - Illustrative examples of outdoor area dose factors (MARSSIM); - Area correction factors as a function of source area (Soil Screening Guidance). Note: the area correction factors were inverted to correspond to a DCGL area factor. - Recommended area correction factors as a function of source area (Soil Screening Guidance); - Ranges for hot spot multiplication factors (RESRAD). As it can be seen

Evolution of industrial wastewater pollution in the Barcelona Metropolitan Area; Evolucion de la contaminacion industrial en las aguas residuales del area metropolitana de Barcelona

Energy Technology Data Exchange (ETDEWEB)

Mantecon Pascual, R.

2005-07-01

The Environmental Agency of the Barcelona Metropolitan Area has full powers regarding sewerage. Industrial wastewater emptied into the public sewer system has been monitored and analysed since 1988. the data showing the evolution of the pollution in industrial wastewater are presented, broken down by activities and parameters. These data are based on the analysis of 14,528 samples taken during 19,555 inspections of 5,655 factories. It was found that there has been a gradual improvement in the quality of the effluents. Failure to meet the requirements concerning one or more of the physico-chemical parameters fell from 71% to 39% of the samples analysed. (Author)

Postwar Industrial areas as agents for sustainable urban transformation

DEFF Research Database (Denmark)

Boye, Anne Mette

2017-01-01

Only 30-40 years old, postwar industrial enclaves in Denmark change character. Vacancies, new investments in high technology and new civic programs are recorded even within the same enclaves. These postwar industrial areas represent a generic typology – a legacy of the functionalistic paradigm sh...... international projects, the paper pinpoints a selection of spatial transformation strategies addressing uncertainty. Through this, the paper contributes to the discussion on how to recycle the postwar urban landscape and planning in uncertain conditions....... are cleared for redevelopment or ignored. However, both reactions dismiss the possible qualities of the existing morphology and activities. This paper argues that this might close an opportunity to consider how recycling these enclaves can be utilized to shape future sustainable urban environments...

Estimation of heavy metals in dust fall samples from three different industrial areas of Karachi

International Nuclear Information System (INIS)

Hashmi, D.R.; Khan, F.A.; Shareef, A.; Bano, A.B.; Munshi, A.B.

2010-01-01

The study of accumulation of heavy metals, Fe, Cu, Mn, Zn, Pb and Cd, in the dust fall samples, collected from three selected industrial areas of Karachi, showed the level of heavy metals to decrease gradually from sites of high activity to those of low activity such as from roundabouts to main roads to side roads. Concentration of heavy metal showed a variation of the order Fe>Zn>Pb>Mn>Cu>Cd. Iron had the highest concentration in all the sampling areas in the range of 1.947 +- 0.00 to 30.039 +- 0.01 mg/g. Lower values were observed for Cd with respective ranges of 0.001 +- 0.00 to 0.009 +- 0.01 mg/g. The results suggested that heavy metal pollution in the dust fall samples of industrial areas may be due to automobile and industrial exhaust from different industrial units. (author)

Heavily nitrogen doped, graphene supercapacitor from silk cocoon

International Nuclear Information System (INIS)

Sahu, Vikrant; Grover, Sonia; Tulachan, Brindan; Sharma, Meenakshi; Srivastava, Gaurav; Roy, Manas; Saxena, Manav; Sethy, Niroj; Bhargava, Kalpana; Philip, Deepu; Kim, Hansung; Singh, Gurmeet; Singh, Sushil Kumar; Das, Mainak; Sharma, Raj Kishore

2015-01-01

Doping of graphene with nitrogen is of much interest, since it improves the overall conductivity and supercapacitive properties. Besides conductivity, nitrogen doping also enhances the pseudo-capacitance due to fast and reversible surface redox processes. In this work, we have developed a cheap and easy process for synthesizing heavily nitrogen doped graphene (15% nitrogen) from non-mulberry silk cocoon membrane (Tassar, Antheraea mylitta) by pyrolyzing the cocoon at 400 °C in argon atmosphere. Further we have investigated the performance of this heavily ‘nitrogen doped graphene’ (NDG) in a supercapacitor device. Our results suggest that NDG obtained from cocoon has improved supercapacitor performance. The improved performance is due to the high electronegativity of nitrogen that forms dipoles on the graphene surface. These dipoles consequently enhance the tendency of graphene to attract charged species to its surface. This is a green and clean synthesis approach for developing electronic materials for energy applications

Heavy Metal In Food Ingredients In Oil Refi nery Industrial Area, Dumai

Directory of Open Access Journals (Sweden)

Dian Sundari

2016-06-01

Full Text Available Background: Industrial waste generally contains a lot of heavy metals such as Plumbum (Pb, Arsenic (As, Cadmium(Cd and Mercury (Hg, which can contaminate the surrounding environment and cause health problems. Bioaccumulation ofheavy metals from the environment can occur in foodstuffs. The study aims to determine levels of heavy metals Pb, Cd, Asand Hg in foodstuffs in the oil refi nery industry. Methods: The analytical method used Atomic Absorption Spectrophotometer(AAS. Samples were taken from two locations, namely: the exposed area and non exposed area. The sample consisted ofcassava, papaya leaves, fern leaves, cassava leaves, guava, papaya and catfi sh. Results: The analysis showed levels ofmetals As in all samples at exposed locations is below the maximum limit of SNI, the location is not exposed only in catfi shlevels of As (2.042 mg/kg exceeds the SNI. Cd levels of both locations are not detected. Pb levels in catfi sh in exposedlocations (1,109 mg/kg exceeds the SNI. Hg levels in leaves of papaya, cassava leaves, fern leaves, cassava and fruitpapaya exceed SNI. Conclusion: There has been a heavy metal contamination in foodstuffs. Recommendation: Thelocal people are advised to be careful when consuming food stuffs from oil refi nery industrial area.

Complex organic pollutant mixtures originating from industrial and municipal emissions in surface waters of the megacity Jakarta-an example of a water pollution problem in emerging economies.

Science.gov (United States)

Dsikowitzky, Larissa; Hagemann, Lukas; Dwiyitno; Ariyani, Farida; Irianto, Hari Eko; Schwarzbauer, Jan

2017-12-01

During the last decades, the global industrial production partly shifted from industrialized nations to emerging and developing countries. In these upcoming economies, the newly developed industrial centers are generally located in densely populated areas, resulting in the discharge of often only partially treated industrial and municipal wastewaters into the surface waters. There is a huge gap of knowledge about the composition of the complex organic pollutant mixtures occurring in such heavily impacted areas. Therefore, we applied a non-target screening to comprehensively assess river pollution in a large industrial area located in the megacity Jakarta. More than 100 structurally diverse organic contaminants were identified, some of which were reported here for the first time as environmental contaminants. The concentrations of paper manufacturing chemicals in river water-for example, of the endocrine-disrupting compound bisphenol A (50-8000 ng L -1 )-were as high as in pure untreated paper industry wastewaters. The non-target screening approach is the adequate tool for the identification of water contaminants in the new global centers of industrial manufacturing-as the first crucial step towards the evaluation of as yet unrecognized environmental risks.

Changing industrial patterns in the metroplitan Chicago area

Energy Technology Data Exchange (ETDEWEB)

Allardice, D.

1994-12-31

The industrial base of Chicago, and most Midwestern cities, continues to change. These changes are particularly visible in the manufacturing sector where the exodus of companies has left behind abandoned factories and industrial sites that now blight the urban landscape. As urban centers have seen a steady decline in their ability to attract and maintain their manufacturing base, great interest has been placed in seeing what can be done to attract economic activity back into the urban center. For most Midwestern cities, this often means trying to either replace or stem the tide of manufacturing facilities that have left the city for {open_quotes}greenfields{close_quotes} in suburban or rural locations or have simply moved overseas. On the replacement front, to compensate for the loss of manufacturing, some cities such as Chicago have managed to expand other areas of their economies, such as business services, finance, and tourism and recreation to maintain their vitality. This paper discusses three aspects of the changing economic landscape of Chicago and other Midwestern urban areas. First, some historical perspective will be provided on how Chicago came to be a manufacturing center and what factors since World War II have led manufacturing facilities to move away from the urban center. Second, the future prospects for manufacturing in the central city will be examined. Finally, what policies may help increase (or at the very least maintain) the concentration of manufacturing in Chicago will be discussed.

Changing industrial patterns in the metroplitan Chicago area

International Nuclear Information System (INIS)

Allardice, D.

1994-01-01

The industrial base of Chicago, and most Midwestern cities, continues to change. These changes are particularly visible in the manufacturing sector where the exodus of companies has left behind abandoned factories and industrial sites that now blight the urban landscape. As urban centers have seen a steady decline in their ability to attract and maintain their manufacturing base, great interest has been placed in seeing what can be done to attract economic activity back into the urban center. For most Midwestern cities, this often means trying to either replace or stem the tide of manufacturing facilities that have left the city for open-quotes greenfieldsclose quotes in suburban or rural locations or have simply moved overseas. On the replacement front, to compensate for the loss of manufacturing, some cities such as Chicago have managed to expand other areas of their economies, such as business services, finance, and tourism and recreation to maintain their vitality. This paper discusses three aspects of the changing economic landscape of Chicago and other Midwestern urban areas. First, some historical perspective will be provided on how Chicago came to be a manufacturing center and what factors since World War II have led manufacturing facilities to move away from the urban center. Second, the future prospects for manufacturing in the central city will be examined. Finally, what policies may help increase (or at the very least maintain) the concentration of manufacturing in Chicago will be discussed

Radio transmission system for industrial area

International Nuclear Information System (INIS)

Iliescu, M.; Culcer, M.; Curuia, M.; Anghel, N.M.; Stefanescu, I.

2003-01-01

The paper deals with a data transmission system operating in a large, noisy industrial area. The radio transmission system permits data and commands communication between the local units of collecting data and a central monitoring and/or command station ( dispatch). The communication support are radio waves in the range 450 MHz. The transducers are of transmitter type, with 4-20 mA output signal, providing information about environmental and/or work parameters. Data are primarily acquisitioned in a data logger with microcontroller, then transmitted via a FSK radio modem and a radio station to the dispatch. Data logger can also be connected in a network. The dispatch personal computer receives and processes data and transmits commands. The system functioning is supervised by a communication software in MCS - 51 assembler and an application software in Visual C ++ . (author)

Background radiation study of Offa industrial area of Kwara State ...

African Journals Online (AJOL)

A study of the external background radiation in Offa industrial area of Kwara State is hereby reported. An in-situ measurement using two Digilert radiation monitors at five different stations were carried out. A mean exposure rate of 0.0132mR/hr, which represents 20% elevation from the standard background radiation, was ...

INDUSTRIAL AREA AS A BASIS FOR SPATIAL OPTIMIZATION OF LAND USE IN KIEV

Directory of Open Access Journals (Sweden)

Tsviakh О.

2017-02-01

Full Text Available In article deals with problem of using the urban land, including land under the industrial objects in Kiev. Also was analysed the ways of optimization the urban land using. Today become particularly acute the problem for efficient use of urban land use, including land for industrial facilities non-functioning as a reserve future development of Kyiv-based ecological-economic approach to solving them. However, to ensure sustainable development of urban population (preserve and improve health, improve working conditions, improve living conditions, increase the construction of social and affordable housing, reducing unemployment, creating new jobs, improving the ecological state of the environment within large cities , you need to identify ways to optimize existing urban land use. The complexity of management decisions is determined, above all, the fact that in most cities of Ukraine territorial resources are exhausted and vacant land plots require significant investment. Also, a significant proportion of non-functioning industrial enterprises, which occupy large areas in the city were in Kyiv surrounded by residential development, buffer zones, technogenic disturbed and contaminated land. These objects be removed outside the settlements and the land on which they are to be re-cultivated and restoration for more ecological, economically feasible and sustainable use. The rapid development of large cities around the world and increase their impact on the environment and society is accompanied by a set ekonominyh, environmental and social issues that significantly influence the development of land relations in settlements in general. Today in Kyiv observed the changing dynamics of land area, which is to reduce the share of agricultural and forestry purposes and to increase the territory of other categories. The process of de-industrialization and suburbanization of urban land use is inevitable. They in turn accelerate other processes - "crowding out

Operation of heavily irradiated silicon detectors in non-depletion mode

International Nuclear Information System (INIS)

Verbitskaya, E.; Eremin, V.; Ilyashenko, I.; Li, Z.; Haerkoenen, J.; Tuovinen, E.; Luukka, P.

2006-01-01

The non-depletion detector operation mode has generally been disregarded as an option in high-energy physics experiments. In this paper, the non-depletion operation is examined by detailed analysis of the electric field distribution and the current pulse response of heavily irradiated silicon (Si) detectors. The previously reported model of double junction in heavily irradiated Si detector is further developed and a simulation of the current pulse response has been performed. It is shown that detectors can operate in a non-depletion mode due to the fact that the value of the electric field in a non-depleted region is high enough for efficient carrier drift. This electric field originates from the current flow through the detector and a consequent drop of the potential across high-resistivity bulk of a non-depleted region. It is anticipated that the electric field in a non-depleted region, which is still electrically neutral, increases with fluence that improves the non-depleted detector operation. Consideration of the electric field in a non-depleted region allows the explanation of the recorded double-peak current pulse shape of heavily irradiated Si detectors and definition of the requirements for the detector operational conditions. Detailed reconstruction of the electric field distribution gives new information on radiation effects in Si detectors

Epibenthic diversity and productivity on a heavily trawled Barents Sea bank (Tromsøflaket

Directory of Open Access Journals (Sweden)

Monika Kędra

2017-04-01

Full Text Available Shallow Arctic banks have been observed to harbour rich communities of epifaunal organisms, but have not been well-studied with respect to composition or function due to sampling challenges. In order to determine how these banks function in the Barents Sea ecosystem, we used a combination of video and trawl/dredge sampling at several locations on a heavily trawled bank, Tromsøflaket – located at the southwestern entrance to the Barents Sea. We describe components of the benthic community, and calculate secondary production of dominant epifaunal organisms. Forty-six epibenthic taxa were identified, and sponges were a significant part of the surveyed benthic communities. There were differences in diversity and production among areas, mainly related to the intensity of trawling activities. Gamma was the most diverse and productive area, with highest species abundance and biomass. Trawled areas had considerably lower species numbers, and significant differences in epifaunal abundance and biomass were found between all trawled and untrawled areas. Trawling seems to have an impact on the sponge communities: mean individual poriferan biomass was higher in untrawled areas, and, although poriferans were observed in areas subjected to more intensive trawling, they were at least five times less frequent than in untrawled areas.

Economical solution for the industrial waste problem of Karachi industrial area

International Nuclear Information System (INIS)

Mubin, S.

2005-01-01

The increased rate of industrialization coupled with rapid urbanization in Pakistan has given rise to serious water pollution and environmental problems. A vast range of industries has been established in the country during the last twenty five years, including tanneries, fertilizers, textiles, refineries, chemicals, vegetable oils, paper am pulp, sugar and food. Little attention was paid towards a large scale release of wastewater from these industries. Presently wastewater produced from these industries has been considered a serious problem and research in being conducted to solve its associated problems. Recently, it has been realized that there is a significant threat of water borne diseases, degradation of fresh water quality, environmental depletion and soil deterioration from the effluent and toxic emission of industries. Being a developing country and having limited resources, it is hard to install treatment plants on the industrial effluent with every industry before discharging them into streams which are also creating disturbance in natural ecosystem. An effort has been made to solve wastewater problem by implementing statistical tools on data of Karachi industrial state, obtained from EPA JICA and PCRWR, Islamabad. (author)

Fuzzy logic applied to prospecting for areas for installation of wood panel industries.

Science.gov (United States)

Dos Santos, Alexandre Rosa; Paterlini, Ewerthon Mattos; Fiedler, Nilton Cesar; Ribeiro, Carlos Antonio Alvares Soares; Lorenzon, Alexandre Simões; Domingues, Getulio Fonseca; Marcatti, Gustavo Eduardo; de Castro, Nero Lemos Martins; Teixeira, Thaisa Ribeiro; Dos Santos, Gleissy Mary Amaral Dino Alves; Juvanhol, Ronie Silva; Branco, Elvis Ricardo Figueira; Mota, Pedro Henrique Santos; da Silva, Lilianne Gomes; Pirovani, Daiani Bernardo; de Jesus, Waldir Cintra; Santos, Ana Carolina de Albuquerque; Leite, Helio Garcia; Iwakiri, Setsuo

2017-05-15

Prospecting for suitable areas for forestry operations, where the objective is a reduction in production and transportation costs, as well as the maximization of profits and available resources, constitutes an optimization problem. However, fuzzy logic is an alternative method for solving this problem. In the context of prospecting for suitable areas for the installation of wood panel industries, we propose applying fuzzy logic analysis for simulating the planting of different species and eucalyptus hybrids in Espírito Santo State, Brazil. The necessary methodological steps for this study are as follows: a) agriclimatological zoning of different species and eucalyptus hybrids; b) the selection of the vector variables; c) the application of the Euclidean distance to the vector variables; d) the application of fuzzy logic to matrix variables of the Euclidean distance; and e) the application of overlap fuzzy logic to locate areas for installation of wood panel industries. Among all the species and hybrids, Corymbia citriodora showed the highest percentage values for the combined very good and good classes, with 8.60%, followed by Eucalyptus grandis with 8.52%, Eucalyptus urophylla with 8.35% and Urograndis with 8.34%. The fuzzy logic analysis afforded flexibility in prospecting for suitable areas for the installation of wood panel industries in the Espírito Santo State can bring great economic and social benefits to the local population with the generation of jobs, income, tax revenues and GDP increase for the State and municipalities involved. The proposed methodology can be adapted to other areas and agricultural crops. Copyright © 2017 Elsevier Ltd. All rights reserved.

Depositional history of sedimentary linear alkylbenzenes (LABs) in a large South American industrial coastal area (Santos Estuary, Southeastern Brazil)

International Nuclear Information System (INIS)

Martins, Cesar C.; Bicego, Marcia C.; Mahiques, Michel M.; Figueira, Rubens C.L.; Tessler, Moyses G.; Montone, Rosalinda C.

2010-01-01

This paper reports the reconstruction of the contamination history of a large South American industrial coastal area (Santos Estuary, Brazil) using linear alkylbenzenes (LABs). Three sediment cores were dated by 137 Cs. Concentrations in surficial layers were comparable to the midrange concentrations reported for coastal sediments worldwide. LAB concentrations increased towards the surface, indicating increased waste discharges into the estuary in recent decades. The highest concentration values occurred in the early 1970s, a time of intense industrial activity and marked population growth. The decreased LAB concentration, in the late 1970s was assumed to be the result of the world oil crisis. Treatment of industrial effluents, which began in 1984, was represented by decreased LAB levels. Microbial degradation of LABs may be more intense in the industrial area sediments. The results show that industrial and domestic waste discharges are a historical problem in the area. - The contamination history of a large South American industrial coastal area indicated by molecular indicator of sewage input.

NO2 and SO2 dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand.

Science.gov (United States)

Chusai, Chatinai; Manomaiphiboon, Kasemsan; Saiyasitpanich, Phirun; Thepanondh, Sarawut

2012-08-01

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO2 and SO2 was conducted using the AERMOD model. The area-specific emission inventories of NOx and SO2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was Jbund, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration overfour selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations Jbfor each individual area, respectively. For AC-NO2, on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO2), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO2, biomass burning has the most influence in all impacted areas (>90%) exceptJor one residential area where on-road mobile is the largest (75%). For AC-SO2, the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO2, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group

Quality index of the surface water of Amazonian rivers in industrial areas in Pará, Brazil.

Science.gov (United States)

Medeiros, Adaelson Campelo; Faial, Kleber Raimundo Freitas; do Carmo Freitas Faial, Kelson; da Silva Lopes, Iris Danielly; de Oliveira Lima, Marcelo; Guimarães, Raphael Mendonça; Mendonça, Neyson Martins

2017-10-15

In this study was to evaluate the waters quality of the Murucupi River, located in urban agglomerate area and intense industrial activity in Barcarena City, Pará State. The Arapiranga River in Abaetetuba City was used as control area (Background), next to Barcarena. Was used the Water Quality Index (WQI) based on nine variables analized. Waters quality of the Arapiranga and Murucupi rivers were regular to good and bad to good, respectively. Anthropogenic influence on the Murucupi River was higher, mainly by the disposal of domestic effluents from the urban agglomerate and of the industrial waste tailing basins upstream of this river. Due to its less inhabited environment and further away from the area urban and industrial, the Arapiranga River was more preserved. Waters pollution of around these area is increasingly intense, and restricted its uses for various purposes. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Remote Excavation of Heavily Contaminated UXO Sites. The Range Master

National Research Council Canada - National Science Library

Crandall, Alan L

2007-01-01

USA Environmental, Inc., and Timberline Environmental Services, Inc., developed the Range Master, a remote controlled scraper with an integrated power screen, to excavate and sift the top 12 inches of heavily contaminated UXO sites...

Contribution of Fugitive Emissions for PM10 Concentrations in an Industrial Area of Portugal

Science.gov (United States)

Marta Almeida, Susana; Viana Silva, Alexandra; Garcia, Silvia; Miranda, Ana Isabel

2013-04-01

Significant atmospheric dust arises from the mechanical disturbance of granular material exposed to the air. Dust generated from these open sources is termed "fugitive" because it is not discharged to the atmosphere in a confined flow stream. Common sources of fugitive dust include unpaved roads, agricultural tilling operations, aggregate storage piles, heavy construction and harbor operations. The objective of this work was to identify the likeliness and extend of the PM10 limit value exceedences due to fugitive emissions in a particularly zone where PM fugitive emissions are a core of environmental concerns - Mitrena, Portugal. Mitrena, is an industrial area that coexists with a high-density urban region (Setúbal) and areas with an important environmental concern (Sado Estuary and Arrábida which belongs to the protected area Natura 2000 Network). Due to the typology of industry sited in Mitrena (e.g. power plant, paper mill, cement, pesticides and fertilized productions), there are a large uncontrolled PM fugitive emissions, providing from heavy traffic and handling and storage of raw material on uncover stockyards in the harbor and industries. Dispersion modeling was performed with the software TAPM (The Air Pollution Model) and results were mapped over the study area, using GIS (Geographic Information Systems). Results showed that managing local particles concentrations can be a frustrating affair because the weight of fugitive sources is very high comparing with the local anthropogenic stationary sources. In order to ensure that the industry can continue to meet its commitments in protecting air quality, it is essential to warrant that the characteristics of releases from all fugitive sources are fully understood in order to target future investments in those areas where maximum benefit will be achieved.

Occupation and lung cancer in two industrialized areas of northern Italy

Energy Technology Data Exchange (ETDEWEB)

Ronco, G.; Ciccone, G.; Mirabelli, D.; Troia, B.; Vineis, P.

1988-03-15

A population-based case-control study on lung cancer was conducted in 2 industrialized areas of northern Italy. Cases (126) were all males who died from lung cancer between 1976 and 1980. Controls (384) were a random sample of males dying from other causes during the same period. Jobs held during working life have been analyzed according to a list of occupations already known to be causally associated with lung cancer (list A) and a list of occupations suspected of being so (list B). Attributable risk percentages in the population for occupations included in either list A or B were about 36% and 12% in the 2 areas. Welders or workers in industries in which welding is common showed elevated odds ratios: 2.9 for welders (95% CI 0.9-9.8); 4.9 (1.1-22.9) for structural metal workers; 11.4 (2.6-49.9) for workers in structural metal production. Other job categories associated with lung cancer included: electricians and workers in electrical machine production, woodworkers (in furniture or cabinet making, but not in carpentry or joinery) and cleaning services. Smoking did not seem to exert a substantial confounding effect. Attributable risk percentages for tobacco smoking were about 78% and 76% in the population of the 2 areas.

Occupation and lung cancer in two industrialized areas of northern Italy.

Science.gov (United States)

Ronco, G; Ciccone, G; Mirabelli, D; Troia, B; Vineis, P

1988-03-15

A population-based case-control study on lung cancer was conducted in 2 industrialized areas of northern Italy. Cases (126) were all males who died from lung cancer between 1976 and 1980. Controls (384) were a random sample of males dying from other causes during the same period. Jobs held during working life have been analyzed according to a list of occupations already known to be causally associated with lung cancer (list A) and a list of occupations suspected of being so (list B). Attributable risk percentages in the population for occupations included in either list A or B were about 36% and 12% in the 2 areas. Welders or workers in industries in which welding is common showed elevated odds ratios: 2.9 for welders (95% CI 0.9-9.8); 4.9 (1.1-22.9) for structural metal workers; 11.4 (2.6-49.9) for workers in structural metal production. Other job categories associated with lung cancer included: electricians and workers in electrical machine production, woodworkers (in furniture or cabinet making, but not in carpentry or joinery) and cleaning services. Smoking did not seem to exert a substantial confounding effect. Attributable risk percentages for tobacco smoking were about 78% and 76% in the population of the 2 areas.

Polybrominated diphenyl ethers in water, sediment, soil, and biological samples from different industrial areas in Zhejiang, China

International Nuclear Information System (INIS)

Wang, Junxia; Lin, Zhenkun; Lin, Kuangfei; Wang, Chunyan; Zhang, Wei; Cui, Changyuan; Lin, Junda; Dong, Qiaoxiang; Huang, Changjiang

2011-01-01

Highlights: ► We examined PBDE concentrations in various matrices from different industrial areas. ► Elevated PBDE levels were found in areas with low-voltage electrical manufactures. ► Areas with e-waste recycling activities also had higher PBDE concentrations. ► PBDE content and composition in water samples varied from one area to another. ► PBDE composition in sediment/soil and biological samples was predominated by BDE-209. - Abstract: Polybrominated diphenyl ethers (PBDEs) have been used extensively in electrical and electronic products, but little is known about their distribution in the environment surrounding the manufacturing factories. This study reports PBDE contamination in various matrices from the location (Liushi, Zhejiang province) that produces more than 70% of the low-voltage electrical appliances in China. Additionally, PBDE contamination was compared with other industries such as the e-waste recycling business (Fengjiang) in the same region. Specifically, we measured seven PBDE congeners (BDEs – 47, 99, 100, 153, 154, 183, and 209) in water, sediment, soil, plant, and animal tissues from four different areas in this region. The present study revealed elevated PBDE concentrations in all matrices collected from Liushi and Fengjiang in comparison with highly industrialized areas without significant PBDE contamination sources. In water samples, there were large variations of PBDE content and composition across different areas. In sediment/soil and biological samples, BDE-209 was the predominant congener and this could be due to the abundant usage of deca-BDE mixtures in China. Our findings provide the very first data on PBDE contamination in the local environments surrounding the electronics industry, and also reveal widespread PBDE contamination in highly industrialized coastal regions of China.

Discrimination of Settlement and Industrial Area Using Landscape Metrics in Rural Region

Directory of Open Access Journals (Sweden)

Xinyu Zheng

2016-10-01

Full Text Available Detailed and precise information of land-use and land-cover (LULC in rural area is essential for land-use planning, environment and energy management. The confusion in mapping residential and industrial areas brings problems in energy management, environmental management and sustainable land use development. However, they remain ambiguous in the former rural LULC mapping, and this insufficient supervision leads to inefficient land exploitation and a great waste of land resources. Hence, the extent and area of residential and industrial cover need to be revealed urgently. However, spectral and textural information is not sufficient for classification heterogeneity due to the similarity between different LULC types. Meanwhile, the contextual information about the relationship between a LULC feature and its surroundings still has potential in classification application. This paper attempts to discriminate settlement and industry area using landscape metrics. A feasible classification scheme integrating landscape metrics, chessboard segmentation and object-based image analysis (OBIA is proposed. First LULC map is generated from GeoEye-1 image, which delineated distribution of different land-cover materials using traditional OBIA method with spectrum and texture information. Then, a chessboard segmentation of the whole LULC map is conducted to create landscape units in a uniform spatial area. Landscape characteristics in each square of chessboard are adopted in the classification algorithm subsequently. To analyze landscape unit scale effect, a variety of chessboard scales are tested, with overall accuracy ranging from 75% to 88%, and Kappa coefficient from 0.51 to 0.76. Optimal chessboard scale is obtained through accuracy assessment comparison. This classification scheme is then compared to two other approaches: a top-down hierarchical classification network using only spectral, textural and shape properties, and lacunarity based hierarchical

Emergy-based comparative analysis on industrial clusters: economic and technological development zone of Shenyang area, China.

Science.gov (United States)

Liu, Zhe; Geng, Yong; Zhang, Pan; Dong, Huijuan; Liu, Zuoxi

2014-09-01

In China, local governments of many areas prefer to give priority to the development of heavy industrial clusters in pursuit of high value of gross domestic production (GDP) growth to get political achievements, which usually results in higher costs from ecological degradation and environmental pollution. Therefore, effective methods and reasonable evaluation system are urgently needed to evaluate the overall efficiency of industrial clusters. Emergy methods links economic and ecological systems together, which can evaluate the contribution of ecological products and services as well as the load placed on environmental systems. This method has been successfully applied in many case studies of ecosystem but seldom in industrial clusters. This study applied the methodology of emergy analysis to perform the efficiency of industrial clusters through a series of emergy-based indices as well as the proposed indicators. A case study of Shenyang Economic Technological Development Area (SETDA) was investigated to show the emergy method's practical potential to evaluate industrial clusters to inform environmental policy making. The results of our study showed that the industrial cluster of electric equipment and electronic manufacturing produced the most economic value and had the highest efficiency of energy utilization among the four industrial clusters. However, the sustainability index of the industrial cluster of food and beverage processing was better than the other industrial clusters.

Promoting energy efficiency in Egyptian industry

International Nuclear Information System (INIS)

Selim, M.H.

1990-01-01

The energy situation in Egypt is characterized by a rather high energy demand, a high annual increase in energy consumption, inefficient utilization of energy, and heavily subsidized energy prices. Energy efficiency is therefore considered to be a matter of top priority, as it would lead to substantial savings. A national policy for efficient use of energy in industry has been outlined, including the establishment of an Industrial Energy Conservation Centre (IECC), the training and upgrading of energy management specialists, and the introduction of energy efficiency technologies in industrial plants. In this article the assistance that international organizations and donors can give to energy efficiency programmes is demonstrated. The results obtained so far are discussed and the lessons, findings and experience gained are outlined. (author). 1 tab

Polybrominated diphenyl ethers in water, sediment, soil, and biological samples from different industrial areas in Zhejiang, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Junxia; Lin, Zhenkun [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Lin, Kuangfei [School of Resources and Environmental Engineering, East China University of Science and Technology/State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, Shanghai 200237 (China); Wang, Chunyan [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Zhang, Wei [School of Resources and Environmental Engineering, East China University of Science and Technology/State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, Shanghai 200237 (China); Cui, Changyuan [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Lin, Junda [Department of Biological Sciences, Florida Institute of Technology, Melbourne, FL 32901 (United States); Dong, Qiaoxiang, E-mail: dqxdong@163.com [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Huang, Changjiang, E-mail: cjhuang5711@163.com [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China)

2011-12-15

Highlights: Black-Right-Pointing-Pointer We examined PBDE concentrations in various matrices from different industrial areas. Black-Right-Pointing-Pointer Elevated PBDE levels were found in areas with low-voltage electrical manufactures. Black-Right-Pointing-Pointer Areas with e-waste recycling activities also had higher PBDE concentrations. Black-Right-Pointing-Pointer PBDE content and composition in water samples varied from one area to another. Black-Right-Pointing-Pointer PBDE composition in sediment/soil and biological samples was predominated by BDE-209. - Abstract: Polybrominated diphenyl ethers (PBDEs) have been used extensively in electrical and electronic products, but little is known about their distribution in the environment surrounding the manufacturing factories. This study reports PBDE contamination in various matrices from the location (Liushi, Zhejiang province) that produces more than 70% of the low-voltage electrical appliances in China. Additionally, PBDE contamination was compared with other industries such as the e-waste recycling business (Fengjiang) in the same region. Specifically, we measured seven PBDE congeners (BDEs - 47, 99, 100, 153, 154, 183, and 209) in water, sediment, soil, plant, and animal tissues from four different areas in this region. The present study revealed elevated PBDE concentrations in all matrices collected from Liushi and Fengjiang in comparison with highly industrialized areas without significant PBDE contamination sources. In water samples, there were large variations of PBDE content and composition across different areas. In sediment/soil and biological samples, BDE-209 was the predominant congener and this could be due to the abundant usage of deca-BDE mixtures in China. Our findings provide the very first data on PBDE contamination in the local environments surrounding the electronics industry, and also reveal widespread PBDE contamination in highly industrialized coastal regions of China.

Monitoring persistent organic pollutants in an industrial area of Tarragona (Catalonia, Spain)

Energy Technology Data Exchange (ETDEWEB)

Nadal, M.; Schuhmacher, M.; Domingo, J.L. [Rovira i Virgili University, Reus (Spain)

2004-09-15

It is well known that combustion of different materials is one of the most important sources of environmental contamination by persistent organic pollutants (POPs). Therefore, environments affected by this kind of processes should be strictly controlled. In relation to it, the 2001 Stockholm Convention for the regulation of POPs was undertaken in order to establish agreements and mechanisms to erase the release of 12 POPs on a global scale. While polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were included in this list, other pollutants such as polychlorinated naphthalenes (PCNs) and polycyclic aromatic hydrocarbons (PAHs) can be added in a near future. Since more than 30 years ago, one of the largest chemical and petrochemical industrial complexes in Southern Europe is located in Tarragona County (Catalonia, Spain). Several chemical industries (such as a PVC production facility and a chlor-alkali plant) and a big oil refinery are located in this residential area (up to 300,000 inhabitants), together with a municipal solid waste incinerator (MSWI) and a hazardous waste incinerator (HWI). Moreover, the presence of a highway and several roads with an important traffic density influences also the environment of the zone. The current study is a preliminary investigation to assess the levels of several POPs (PCDD/Fs, PCBs, PCNs and PAHs) in soil and vegetation samples collected in Tarragona's industrial and residential areas and to compare them with data obtained in unpolluted sites as well as in other industrial and residential zones.

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Science.gov (United States)

Gallego, E.; Roca, F. X.; Perales, F.; Ribes, A.; Carrera, G.; Guardino, X.; Berenguer, M. J.

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200-300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.-246 and n.d.-29 μg m -3 for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.-164 and n.d.-29 μg m -3 for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.

Some of physiological and biochemical responses of Prunus amygdalus to air pollution of the Shazand industrial area

Directory of Open Access Journals (Sweden)

Mehri Askari Mehrabadi

2016-06-01

Full Text Available In today's world where human life is dependent on the industry, the problems impose in the human life along with theachievement of growing in the field of industrial works. One of the challenging problems is entry of pollutants into air that has the destructive effects on human life and environment especially plants. Plants show different responses against the air pollutants. Plant responses can be vary due to climate, geography and plant species. In this study, the effects of air pollutants in the Shazand industrial area (refinery, petrochemical and thermal power stationin Markazi province has been checked on almond. For this purpose, the leaves of almond in Haftadgholle (control area, Shazand (closest city to industrial zone and Kazaz (adjacent industrial zone were collected. Also, soil samples were collected from three areas to determine lead and zinc amounts in soil. Results showed that proline, sulfur, heavy metals (lead and zinc and lipid peroxidation enhanced significantly in Kazaz and Shazand in compared with Haftadgholle, while antioxidant activity of catalase, superoxide dismutase and guaicol peroxidase didn’t significant changes in three areas. The increase of sulfur amount in leaves, lead and zinc in soil of the Kazaz and Shazand regions could be one of the reasons to prove the presence of pollutants in these areas. The increase of lipid peroxidation indicative plant damage against the air pollution. The plant defense mechanism against of stress is the increase of non-enzymatic antioxidant proline. No change in chlorophylls and protein contents reflects increased resistance to the stress.

Simultaneous rota-stenting and transcatheter aortic valve implantation for patients with heavily calcified coronary stenosis and aortic stenosis

Directory of Open Access Journals (Sweden)

Yung-Tsai Lee

2016-09-01

Full Text Available Given that coronary artery disease (CAD in octogenarians undergoing transcatheter aortic valve implantation (TAVI often presents with more complex lesions and extensive calcification, rotational atherectomy (RA may be needed in some cases before stenting. However, data regarding the feasibility and safety of simultaneous RA during TAVI using the Medtronic CoreValve (MCV; Medtronic, Minneapolis, MN, USA system are lacking. Three out of 107 (2.8% patients (2 females, average age 85.6 years, mean aortic valve area 0.5 cm2, mean left ventricular ejection fraction 39%, mean Logistic EuroScore 70%, with complex, heavily calcified coronary stenosis, and severe valvular aortic stenosis (AS were treated with TAVI and RA due to high surgical risk. After balloon valvuloplasty, all coronary lesions were successfully treated with RA and stenting, immediately followed by transfemoral TAVI with a self-expandable MCV. Our data suggested that in the very elderly patients with severe and heavily calcified CAD and AS who were turned down for cardiac surgery, RA and stenting followed by TAVI may be performed successfully in a combined, single-stage procedure.

Analysis of the special consequences of the Barij essence industrial complex of Kashan in the development of neighboring rural areas

Directory of Open Access Journals (Sweden)

Mohsen Shaterian

2017-04-01

Full Text Available In the late decades, the development of industrial activities in the rural areas of Iran have caused some changes in different aspects of these areas which influence the special patterns of rural areas. This article aims to identify the changes that have been the results of industrial development and it’s reflection in the development of rural residential areas. The main intention of this study is to analyze the special consequences (economic, social and anatomical of the industrial center of Kashan in the development of neighboring rural areas. The industrial center consists of three factories that are for making essence, making equipment for gardeners and distillers and the Barij Company. All of the above companies are called the Industrial Center of Barij Essence. It has employed 1050 workers from amongst whom 120 people were identified and the questionnaires were randomly distributed among these workers. To analyze the data based on the measurement variables, descriptive and analytic methods (T were used. The results showed that economically, having rural industries has led to an increase in the people’s intake of  calories, seeing more consumption in long lasting goods and more satisfaction in the native people of the area. In addition, there is more social involvement,  improvements in not wasting the residents’ free time, decreasing of  natives immigration out of the rural areas and finally anatomically, quantity and quality improvement in the rural houses.

Comparative study of the growth and carbon sequestration potential of Bermuda grass in industrial and urban areas

Directory of Open Access Journals (Sweden)

Usman Ali

2018-06-01

Full Text Available Climate change is a global phenomenon occurring throughout the world. Greenhouse gases (GHGs especially carbon dioxide (CO2 considered to be the major culprit to bring these changes. So, carbon (C sequestration by any mean could be useful to reduce the CO2 level in atmosphere. Turf grasses have the ability to sequester C and minimize the effects of GHGs on the environment. In order to study that how turf grasses can help in C sequestration, Bermuda grass (Cynodon dactylon was grown both at industrial and urban location and its effect on C storage were assessed by soil and plant analysis. Dry deposition of ammonium and nitrate was maximum at both locations through the year. However wet deposition was highest during the months of high rainfall. It was examined through soil analysis that soil organic matter, soil C and nitrogen in both locations increased after second mowing of grass. However, soil pH 6.68 in urban and 7.00 in industrial area and EC 1.86 dS/m in urban and 1.90 dS/m in industrial area decreased as the grass growth continue. Soil fresh weight (27.6 g in urban and (27.28 g industrial area also decreased after first and second mowing of grass. The C levels in plant dry biomass also increased which showed improved ability of plant to uptake C from the soil and store it. Similarly, chlorophyll contents were more in industrial area compared to urban area indicates the positive impact of high C concentration. Whereas stomatal conductance was reduced in high C environment to slow down respiration process. Hence, from present study it can be concluded that the Bermuda grass could be grown in areas with high C concentration in atmosphere for sequestrating C in soil.

Life Cycle Assessment of waste management systems in Italian industrial areas: Case study of 1st Macrolotto of Prato

International Nuclear Information System (INIS)

Tarantini, Mario; Loprieno, Arianna Dominici; Cucchi, Eleonora; Frenquellucci, Ferdinando

2009-01-01

Life Cycle Assessment (LCA) is not widely used as a decision-supporting tool in Italy, despite recent European Commission policies fostering its adoption to achieve an energy- and resource-efficient economy. In this paper, an LCA of waste management system of the 1st Macrolotto industrial area is presented. The aims of the study were to identify the environmental critical points of the system and to evaluate opportunities and problems in applying this methodology at industrial area level. After a description of the waste management system of the 1st Macrolotto industrial area, the main assumptions of the study and some elements of the system modelling are presented. Results confirmed that door-to-door separated collection and packaging recycling are successful strategies for reducing the use of natural resources. The cooperation of the waste management company, which was part of the area management structure, was strategic for the completion of the analysis. Country-specific databases and models should be developed for a widespread application of the LCA methodology to waste management in Italian industrial areas.

Positron trapping in heavily irradiated semiconductors

International Nuclear Information System (INIS)

Moser, P.; Pautrat, J.L.; Corbel, C.; Hautojarvi, P.

1985-01-01

Vacancy processes are studied in several heavily irradiated semiconductors. Specimens are ZnTe, CdTe, CdTe (In), InP, InP (Cr), InP (Zn) and Ge. Irradiations are made at 20 K using a 3 MeV Van de Graaff electron accelerator. Doses are 4 x 10 18 e - /cm 2 . Lifetime measurements are made at 77 K at each step of an isochronal annealing (30 min 20 K). In each specimen, the results show a significant increase of the lifetime (+ 30 at + 50 ps) which anneals out in different steps restoring the initial lifetime. The steps are sharp (ΔT/T=0.3) with the exception of InP, InP(Cr), InP(Zn), (ΔT/T=0.9). Tentative interpretations are given

Levels and isomer profiles of Dechlorane Plus in the surface soils from e-waste recycling areas and industrial areas in South China

Energy Technology Data Exchange (ETDEWEB)

Yu Zhiqiang [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Lu Shaoyou; Gao Shutao; Wang Jingzhi [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Li Huiru, E-mail: huiruli@gig.ac.c [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Zeng Xiangying; Sheng Guoying; Fu Jiamo [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2010-09-15

Dechlorane Plus (DP) is a highly chlorinated flame retardant. Levels of DP were measured in surface soils from e-waste recycling areas and industrial areas in South China. Higher DP levels were found in e-waste recycling areas (undetectable-47.4 ng/g) than those in industrial areas (0.0336-4.65 ng/g) in South China. The highest DP concentration (3327 ng/g) was found at the e-waste recycling site in Qingyuan, while DP levels fell dramatically with increasing distance away from the recycling site, suggesting that the e-waste recycling activities are an important source of DP emissions. The mean ratios of anti-DP to total DP (f{sub anti}) for different sampling areas ranged from 0.58 to 0.76 and showed no significant difference from the ratio for the technical DP products (t-test, p > 0.05). Further intensive studies are needed to investigate the process of DP degradation and its degradation products. - High DP concentrations were found in the soils from e-waste recycling regions, and e-waste recycling was the major source of DP emissions in South China.

Environmental pollution study around a large industrial area near Cairo, Egypt

International Nuclear Information System (INIS)

Abdel-Halim, A.S.

2003-01-01

Neutron activation analysis is one of the most extensively used methods for environmental studies due to its high sensitivity, precision, versatility and multielemental character. Cement factories at Helwan, south of Cairo, contribute substantially to environmental pollution. Determination of minor and trace-elements in dust particulates from the cement industrial areas has been performed to assess the air quality from an environmental and human health point of view. Soil-7 standard reference material from IAEA and SRM-1571 from NBS were used for quality assurance testing. The data obtained indicate there is an indication that the pollution could be hazardous to people living in and around the area surveyed. (author)

Near-infrared free carrier absorption in heavily doped silicon

International Nuclear Information System (INIS)

Baker-Finch, Simeon C.; McIntosh, Keith R.; Yan, Di; Fong, Kean Chern; Kho, Teng C.

2014-01-01

Free carrier absorption in heavily doped silicon can have a significant impact on devices operating in the infrared. In the near infrared, the free carrier absorption process can compete with band to band absorption processes, thereby reducing the number of available photons to optoelectronic devices such as solar cells. In this work, we fabricate 18 heavily doped regions by phosphorus and boron diffusion into planar polished silicon wafers; the simple sample structure facilitates accurate and precise measurement of the free carrier absorptance. We measure and model reflectance and transmittance dispersion to arrive at a parameterisation for the free carrier absorption coefficient that applies in the wavelength range between 1000 and 1500 nm, and the range of dopant densities between ∼10 18 and 3 × 10 20  cm −3 . Our measurements indicate that previously published parameterisations underestimate the free carrier absorptance in phosphorus diffusions. On the other hand, published parameterisations are generally consistent with our measurements and model for boron diffusions. Our new model is the first to be assigned uncertainty and is well-suited to routine device analysis

Comparison of DDT and its metabolites concentrations in cow milk from agricultural and industrial areas.

Science.gov (United States)

Kuba, Jarosław; Tomza-Marciniak, Agnieszka; Pilarczyk, Bogumiła; Tarasewicz, Natalia; Pilarczyk, Renata; Ligocki, Marek

2015-01-01

The risk of pesticidal intoxication in humans is severe, especially because of the strongly negative impact on human health. The consequences of the exposure to these substances may include cancerogenesis or endocrine abnormalities resulting for example in decreased fertility. Therefore, the aim of our study was to evaluate the content of dichlorodiphenyltrichloroethane (DDT) and its metabolites in cow milk from two regions of Poland, varying by level of industrialization. Samples were collected from agricultural (n = 25) and industrial (n = 25) areas, and the concentrations of DDT and its metabolites were evaluated by gas chromatography. Residues of DDT were detected in all the milk samples tested, mostly in the samples from the agricultural area, where a total DDT median concentration reached 0.336 μg L(-1). In the milk samples from the industrial area, the median concentration was lower, at 0.131 μg L(-1). 4,4'-DDT was the main metabolite, constituting 83% of total DDT metabolites. Although none of the samples exceeded the level above which they should be considered dangerous, the results showed that the problem of DDT had not diminished and so should be constantly monitored.

Spatial clustering of knowledge-based industries in the Helsinki Metropolitan Area

Directory of Open Access Journals (Sweden)

Juan Eduardo Chica

2016-01-01

Full Text Available The central locations of metropolitan areas have some specific attributes, leading to an accumulation of large knowledge exchanges and extensive knowledge externalities, which encourage the concentration of various economic activities, especially knowledge-based industries (KBI. Other agglomeration economies found in metropolitan areas – such as telecommunications and transport infrastructures connected to global productive circuits and complementary labour markets – are key factors for KBI employment growth. This paper explores the Helsinki Metropolitan Area’s (HMA spatial clustering of KBI at the sub-district level, and the role played by agglomeration economies (both specialization and diversity economies in fostering this process. The results reveal that KBI employment shows patterns of concentration in the core and adjacent areas. The specialization and diversity economies found in the metropolitan core and the specialization economies found in others areas lead to KBI spatial clustering in the HMA. Public policies regarding the promotion of science parks have also played a decisive role.

Characterisation of Radioactive Waste located at Shelter Industrial Site

International Nuclear Information System (INIS)

Brown, T.D.; Billon, F.; Rudko, V.M.; Batiy, V.G.; Panasyuk, N.I.

2001-04-01

As a result of the accident at the unit 4 reactor at the Chernobyl Nuclear Power Plant on the 26 April 1986 there was widespread radioactive contamination of the surrounding area. The area immediately surrounding Unit 4, referred to as the Industrial Site, was very heavily contaminated with fuel and core debris ejected from the reactor. Immediate action was undertaken to reduce the local radiation hazard and mitigate the potential of secondary contamination of the environment. This action involved (a) the removal and collection of fuel fragments (b) removal of the top layer of soil around unit 4 and (c) preparation of a new surface over the Industrial Site. This new surface is referred to colloquially as the Techno-genic Layer. This report provides an overview of a project undertaken for DG-Environment of European Commission by a Consortium consisting of SGN (France) and AEA Technology (UK) working in collaboration with the Organisation, National Academy of Sciences of Ukraine; the Interdisciplinary Scientific and Technical Centre Shelter''. The project consisted of 3 Phases and a total of 14 Tasks. The main purpose of Phase 1 was to review previous work and available information and data on the contamination of the Industrial Site, construction of the Techno-genic Layer, Buttress and Pioneer Walls. Phase 2 was directed at additional measurements being carried out on existing boreholes and core samples to improve and/or substantiate existing information and data. Estimation of likely radioactive waste arisings, recovery procedures and a generalised strategy with indicative costs for the management of the waste was also covered by Phase 2. In Phase 3 new boreholes (3 off) were drilled and subsequently investigated. The justification behind Phase 3 was the desire/need to obtain more reliable information on the so-called high-active waste buried in the Industrial Site. (author)

Providing Public Space Continuities in Post-Industrial Areas through Remodelling Land/Water Connections

Science.gov (United States)

Burda, Izabela M.; Nyka, Lucyna

2017-10-01

This article examines the problem of urban transformation strategies applied in recent years which are based on the creation of new water areas and modification of existing ones. The research is an attempt to prove that modifications of plans of water areas and forms of their borders may play an important role in achieving the best quality public spaces in post-industrial territories. The basis for demonstrating the importance of modifying water borders, and introducing new forms of water-based structures in cities, are theoretical surveys, comparative studies and in-field analyses. It can be seen that post-industrial areas, which used to create voids in the urban fabric, can be perceived as unique but isolated places that should be integrated into the layout of cities. Thus, creating continuity of public spaces that will relate converted areas to their surroundings is a well-known objective of many transformation strategies. This research proves that an effective strategy toward achieving this goal can be based on the modification of relationships between land and water. Namely, the introduction of new water areas, designing new pieces of land that protrude into the water, softening the boundaries of water lines or the opposite, like structuring smaller water flows into well-defined canals, may significantly contribute to the quality of public spaces. As such, all of this fosters the development of sustainable cities and contributes significantly to the emergence of high-quality urban landscapes.

Addition of sunitinib to cetuximab and irinotecan in patients with heavily pre-treated advanced colorectal cancer

DEFF Research Database (Denmark)

Qvortrup, Camilla; Jensen, Benny Vittrup; Jørgensen, Trine Lembrecht

2010-01-01

Results of continuous sunitinib, in combination with cetuximab and irinotecan every other week (SIC) for compassionate use in heavily pre-treated patients with mCRC are presented.......Results of continuous sunitinib, in combination with cetuximab and irinotecan every other week (SIC) for compassionate use in heavily pre-treated patients with mCRC are presented....

Significance of material analysis in industry

International Nuclear Information System (INIS)

Bourke, T.M.

1999-01-01

Full text: Most industries need to have laboratories to meet production, customer and statutory requirements. Failure to have such a service would result in production losses, material failures and customer complaints leading to expensive claims for damages. Laboratory functions are to monitor production processes, certify the end product and assist in trouble shooting production problems and material failures. This means that laboratories are an essential part of industry and need to have access to a wide range of instrumentation (XRF, XRD, AES, ICP, SEM, etc). Monitoring and reporting on the industries environmental licences for effluent and emissions is also the responsibility of the laboratory. Licence exceedance leads to heavy fines and continual exceedance would result in plant closure. The mining industry relies heavily on laboratories to certify that the material meets the customer specification. The large tonnages involved means that small errors in composition can result in losses amounting to many thousands of dollars. Copyright (1999) Australian X-ray Analytical Association Inc

Gemcitabine and capecitabine for heavily pre-treated metastatic colorectal cancer patients

DEFF Research Database (Denmark)

Spindler, Karen-Lise G; Pallisgaard, Niels; Andersen, Rikke F

2014-01-01

AIM: We investigated the efficacy and safety of capecitabine and gemcitabin (GemCap) in heavily pre-treated, therapy-resistant metastatic colorectal cancer (mCRC) patients and the clinical importance of cell-free DNA (cfDNA) measurement. PATIENTS AND METHODS: Patients' inclusion criteria included...

Wind energy in industrial areas optional, but not obvious. A study on the chances and constraints for the use of wind energy in industrial parks

International Nuclear Information System (INIS)

Schoolderman, J.A.; Verbeet, E.; Jochems, A.; Versteeg, K.

2000-06-01

The feasibility of installing wind turbines in industrial parks in the Netherlands has been investigated. An overview is given of possibilities and constraints to fit in wind turbines in industrial areas, based on the results of a literature study, a market consultation of sectoral organizations, representatives of local industrial circles and industrial experts in the field of renewable energy. Also a telephone survey was carried out among 130 entrepreneurs in the Netherlands to determine their attitudes towards the use of sustainable energy and wind energy in industrial parks. The results of the attitude study are published in a separate report for which a separate abstract has been prepared. The intermediate results were discussed at a meeting (23 February 2000), in which representatives from the industry, provinces, municipalities and the government participated

Analysis of phthalate esters in soils near an electronics manufacturing facility and from a non-industrialized area by gas purge microsyringe extraction and gas chromatography

Energy Technology Data Exchange (ETDEWEB)

Wu, Wei [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Hu, Jia [Suzhou Center for Disease Prevention and Control, Suzhou, Jiangsu (China); Wang, Jinqi; Chen, Xuerong; Yao, Na [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Tao, Jing, E-mail: jingtao1982@126.com [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Zhou, Yi-Kai, E-mail: zhouyk@mails.tjmu.edu.cn [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China)

2015-03-01

Here, a novel technique is described for the extraction and quantitative determination of six phthalate esters (PAEs) from soils by gas purge microsyringe extraction and gas chromatography. Recovery of PAEs ranged from 81.4% to 120.3%, and the relative standard deviation (n = 6) ranged from 5.3% to 10.5%. Soil samples were collected from roadsides, farmlands, residential areas, and non-cultivated areas in a non-industrialized region, and from the same land-use types within 1 km of an electronics manufacturing facility (n = 142). Total PAEs varied from 2.21 to 157.62 mg kg{sup −1} in non-industrialized areas and from 8.63 to 171.64 mg kg{sup −1} in the electronics manufacturing area. PAE concentrations in the non-industrialized area were highest in farmland, followed (in decreasing order) by roadsides, residential areas, and non-cultivated soil. In the electronics manufacturing area, PAE concentrations were highest in roadside soils, followed by residential areas, farmland, and non-cultivated soils. Concentrations of dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP) differed significantly (P < 0.01) between the industrial and non-industrialized areas. Principal component analysis indicated that the strongest explanatory factor was related to DMP and DnBP in non-industrialized soils and to butyl benzyl phthalate (BBP) and DMP in soils near the electronics manufacturing facility. Congener-specific analysis confirmed that diethylhexyl phthalate (DEHP) was a predictive indication both in the non-industrialized area (r{sup 2} = 0.944, P < 0.01) and the industrialized area (r{sup 2} = 0.860, P < 0.01). The higher PAE contents in soils near the electronics manufacturing facility are of concern, considering the large quantities of electronic wastes generated with ongoing industrialization. - Highlights: • A new method for determining phthalate esters in soil samples was developed. • Investigate six phthalates near an industry and a

The potential for ore and industrial minerals in the Forsmark area

Energy Technology Data Exchange (ETDEWEB)

Lindroos, Hardy [MIRAB Mineral Resurser AB, Uppsala (Sweden); Isaksson, Hans; Thunehed, Hans [GeoVista AB, Luleaa (Sweden)

2004-03-01

A survey has been made of existing information concerning the potential for ore and industrial minerals in and near the candidate area for a deep repository in Forsmark. A deep repository for spent nuclear fuel should not be located in a rock type or an area where mineral extraction might be considered in the future, since this would make it impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities. The survey has made use of all the geoscientific information that was compiled in the more regional investigations in Oesthammar Municipality in 1996-97. In cooperation with the Geological Survey of Sweden (SGU), a new, more detailed mineral resources map has been prepared. The map shows areas with an ore potential that may be unsuitable or unfavourable for siting of a deep repository. The results of the recently completed geophysical helicopter surveys of the Forsmark area are presented in a special chapter. The judgement of the area's ore potential is in part based on the geophysical evaluation of these measurements. Furthermore, the survey obtained information from ongoing deep drillings from the site investigation in Forsmark. In order to better be able to judge the ore potential, the survey has initiated a geochemical investigation of activated soil samples, plus an ore geology sampling of a section in the deep borehole KFM02A, where a hydrothermally altered zone was detected in 2003.The first results from these samplings are presented in the report, which also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. Some suggestions are made for further ore geology investigations. The mineral resources map shows that there is an elongate northwest-southeast zone south and southwest of the candidate area which has a potential for skarn iron ore, and possibly for copper and zinc

The potential for ore and industrial minerals in the Forsmark area

International Nuclear Information System (INIS)

Lindroos, Hardy; Isaksson, Hans; Thunehed, Hans

2004-03-01

A survey has been made of existing information concerning the potential for ore and industrial minerals in and near the candidate area for a deep repository in Forsmark. A deep repository for spent nuclear fuel should not be located in a rock type or an area where mineral extraction might be considered in the future, since this would make it impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities. The survey has made use of all the geoscientific information that was compiled in the more regional investigations in Oesthammar Municipality in 1996-97. In cooperation with the Geological Survey of Sweden (SGU), a new, more detailed mineral resources map has been prepared. The map shows areas with an ore potential that may be unsuitable or unfavourable for siting of a deep repository. The results of the recently completed geophysical helicopter surveys of the Forsmark area are presented in a special chapter. The judgement of the area's ore potential is in part based on the geophysical evaluation of these measurements. Furthermore, the survey obtained information from ongoing deep drillings from the site investigation in Forsmark. In order to better be able to judge the ore potential, the survey has initiated a geochemical investigation of activated soil samples, plus an ore geology sampling of a section in the deep borehole KFM02A, where a hydrothermally altered zone was detected in 2003.The first results from these samplings are presented in the report, which also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. Some suggestions are made for further ore geology investigations. The mineral resources map shows that there is an elongate northwest-southeast zone south and southwest of the candidate area which has a potential for skarn iron ore, and possibly for copper and zinc, although

Scale up and application of equal-channel angular extrusion for the electronics and aerospace industries

International Nuclear Information System (INIS)

Ferrasse, Stephane; Segal, V.M.; Alford, Frank; Kardokus, Janine; Strothers, Susan

2008-01-01

Two areas are critical to promote equal-channel angular extrusion beyond the stage of a laboratory curiosity: (i) tool/processing design and scale up; (ii) development of new submicrometer-grained products. Both goals are pursued at Honeywell. The first case is the successful commercialization of ECAE for the production of sputtering targets from single phase alloys in the electronic industry. Blank dimensions are significantly larger than those reported in the literature. Other described applications are targeted to the increase of tensile strength, high-cycle fatigue and toughness in medium-to-heavily alloyed Al materials used in aerospace. In these alloys, the optimal properties can be reached with better understanding of the interplay between plastic deformation and precipitation mechanisms

Radiological protection in the industrial area

International Nuclear Information System (INIS)

Fraga, H.

2008-12-01

Radiation protection (RP) in industrial applications is composed of four major themes that are recruiting and training personnel, equipment and instrumentation, materials used and also the acquisition of new technologies to improve their own RP. To carry out the recruitment of staff and train them to serve as occupationally exposed personnel in the industry continues with the Mexican Official Standard NOM-031-NUCL-1999, R equirements for qualification and training of personnel occupationally exposed to radiation ionizing , what will be done regarding the physical fitness of personnel by NOM-026-NUCL-1999, M edical surveillance of personnel occupationally exposed to ionizing radiation . The principle of optimization of the RP, or ALARA principle (keeping the risk as low as reasonably achievable), is assumed to be the safety philosophy in the field of industrial applications of ionizing radiation. Practically all the elements that make up the equipment, instrumentation and materials used in industrial radiography and other industrial applications, has an orientation towards the protection, along with procedures that operate. For example, in industrial radiography the technician always has several instruments for radiation detection and measurement, some with visible and audible alarms. The equipment characteristics and transport (containers) are regulated by the standards NOM-025/1- 2000 and NOM-025/2-2996, which contains requirements for radiological safety in design and operation, respectively, for both as containers for some of its parts and accessories. As part of the technological innovation with benefits to the RP itself and eventually target practice today are venturing into the radiography digital, which involves the exposure of a plate image phosphorus-based with the later download to a computer. In combination with the use of sources of X-rays, there is a real contribution to reducing the dose, since the later are nowadays equipped with programmable

An overall index of environmental quality in coal mining areas and energy facilities.

Science.gov (United States)

Vatalis, Konstantinos I; Kaliampakos, Demetrios C

2006-12-01

An approach to measuring environmental quality and trends in coal mining and industrial areas was attempted in this work. For this purpose, the establishment of a reference scale characterizing the status of environmental quality is proposed by developing an Environmental Quality Index (EQI). The methodology involves three main components: social research, the opinion of environmental experts, and the combination of new or existing indices. A survey of public opinion was carried out to identify the main environmental problems in the region of interest. Environmental experts carried out a survey, and the weights of specific environmental problems were obtained through a fuzzy Delphi method and pairwise comparison. The weight attributed to each environmental problem was computed, using new or existing indices (subindices) in the relevant literature. The EQI comprises a combination of the subindices with their own weights. The methodology was applied to a heavily industrialized coal basin in northwestern Macedonia, Greece. The results show that the new index may be used as a reliable tool for evaluating environmental quality in different areas. In addition, the study of EQI trends on an interannual basis can provide useful information on the efficiency of environmental policies already implemented by the responsible authorities.

Iron, Oil, and Emeryville: Resource Industrialization and Metropolitan Expansion in the San Francisco Bay Area, 1850-1900

OpenAIRE

Lunine, Seth

2013-01-01

Scholars have largely overlooked the formative role of industry in both California's economic development and the San Francisco Bay Area's metropolitan expansion during the late nineteenth century. Beginning in the early 1880s, leading firms in San Francisco's specialized industries, such as the iron and chemicals sectors, dispersed to the metropolitan periphery. This process of industrial suburbanization created an integrative metropolitan economy, as well as individual suburbs. In this di...

Some important applications of accelerators in medicine and industry

International Nuclear Information System (INIS)

Jongen, Y.

1996-01-01

Accelerators, and cyclotrons in particular, have long been dedicated to research. Nowadays, they are industrial devices heavily used in various fields. The Belgian company Ion Beam Applications, probably the largest private company manufacturing cyclotrons, has largely contributed to the dissemination of this technology into the medical and radio-pharmaceutical community. This paper will present different applications of cyclotrons in these fields, from radioisotope production to radiotherapy, based on IBA's experience since 1986, date of construction of the CYCLONE 30 prototype, a cyclotron that revolutionized cyclotron technology for medicine and industry. Possible industrial applications of cyclotrons will also be mentioned, together with applications of another type of accelerator recently introduced in the market by IBA: the Rhodotron. (author)

Study on the Pollution-heaven Hypothesis Focusing on Pollution-Intensive Industries

Energy Technology Data Exchange (ETDEWEB)

Lho, S.W. [Kyungnam University, Masan (Korea)

2002-03-01

The purpose of this study is to test pollution-heaven hypothesis on the Korean pollution-intensive industries, that is, textile and clothing, petrochemical and primary metal industry. The empirical study examines that foreign direct investment(FDI) of Korean pollution-intensive industries regresses on couple of exogenous variables and the environmental regulation on FDI. As the environmental regulation is not directly observed, it uses C0{sub 2} emissions as the pollutant. The results of the study show that the environmental regulation in a host country is an insignificant determinant of FDI for the Korean polluting industries. That is, they do not support Leonard (1988), Xing and Kolstad (2000) that the hypothesis is a significant for heavily polluting industries. (author). 34 refs., 10 tabs.

Low VOC Barrier Coating for Industrial Maintenance

Science.gov (United States)

2007-11-01

Property Documented No less than 7 mils Property Documented Properties Documented Property Documented Property Documented LVBC Fingerprint ... canvas or other approved shoe covers when walking on coated surfaces, regardless of curing time allowed. For heavily trafficked areas, provide

Peat wetland as a natural filter of effluents from adjacent industrial areas

Directory of Open Access Journals (Sweden)

József DEZSO

2015-12-01

Full Text Available The main objective of the project is the study of a peat wetland functioning as recipient of effluents from former and present-day industrial activities. The investigation was focused on heavy metal contaminations and their probable mobilization or fixation. The studied peatbog is a typical Eastern European wetland, located in Hungary on the border between medium mountains (Bakony Mountains and a Neogene basin (the Sárrét, an area under nature conservation. Watercourses and prevailing air currents can transport contaminants from industrial areas to the wetland. At first the basic parameters of surface waters and subsurface conditions (soils, groundwater were investigated. These parameters (EC, Cl are possible indicators of contamination. Subsequently, the amounts of heavy metals (Cd, Pb extracted by solution in two steps (HCl, CaCl2 were measured using atomic absorption spectroscopy (AAS. The extracted values indicate what amounts of which elements could be mobilized by human impact and/or production of humic acids, which occasionally emerges during the remediation works. The total heavy metal concentrations in the samples were investigated by X-ray fluorescence method. Based on the investigation, the peatbog is claimed to function as a natural filter.

Effect of soap industry effluents on soil and ground water in Albageir area

International Nuclear Information System (INIS)

Awadalla, S. O.

2004-02-01

This study investigates the effect on soil and ground water produced by the effluent from soap industry discharged from Alsheikh Mustafa Alamin (SMA) factory, in Albageir industrial area, located 45 Km south of Khartoum. Soil samples were taken from the periphery of the effluent pond and from 25 and 50 cm depths from pits at different distances from the pond.The samples were analyzed for the following chemical and physical characteristics PH, EC, sodium, chloride ions and their grain size, in order to investigate any possible soil degradation. The results showed that there is an increase in soil salinity and sodicity resulting from the improper discharge of the liquid waste, and from lack of treatment before the discharge. Hence, there are definitive signs for soil degradation in the study area, which could reach a high magnitude in the long.This situation could be rectified by adopting updated techniques for treatment and disposal of effluent, and by regular inspection, by the authorities in order to make sure that the regulations are not violated. Chemical and physical analyses of ground water samples showed no signs of pollution. However, if the disposal practices are not revised, the possibility of pollution in the near future is likely to occur. A package of measurements is proposed in order to curb the impact of the industry on the environment. (Author)

Development and Application of Environmental Quality of Life Scale among People Residing near Three Types of Industrial Areas, Southern Thailand

Science.gov (United States)

Sopsuk, Jirawan; Chongsuvivatwong, Virasakdi; Sornsrivichai, Vorasith; Hasuwanakit, Supat

2013-01-01

To compare QOL among rural people living in three different industrial areas and one non-industrial area in southern Thailand. A questionnaire based on the WHOQOL-BREF with environmental assessment was initially developed. After consultation with experts and pilot study, it was tested to check internal reliability and further modified as…

Mid-infrared plasmonic resonances exploiting heavily-doped Ge on Si

Science.gov (United States)

Biagioni, P.; Sakat, E.; Baldassarre, L.; Calandrini, E.; Samarelli, A.; Gallacher, K.; Frigerio, J.; Isella, G.; Paul, D. J.; Ortolani, M.

2015-03-01

We address the behavior of mid-infrared localized plasmon resonances in elongated germanium antennas integrated on silicon substrates. Calculations based on Mie theory and on the experimentally retrieved dielectric constant allow us to study the tunability and the figures of merit of plasmon resonances in heavily-doped germanium and to preliminarily compare them with those of the most established plasmonic material, gold.

Polycyclic aromatic hydrocarbons associated with particles in ambient air from urban and industrial areas

Energy Technology Data Exchange (ETDEWEB)

Rehwagen, Martina; Mueller, Andrea; Herbarth, Olf [UFZ-Centre for Environmental Research Leipzig-Halle, Department of Human Exposure Research and Epidemiology, Permoserstr. 15, D 04318 Leipzig (Germany); Massolo, Laura; Ronco, Alicia [CIMA Centro de Investigaciones del Medio Ambiente, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, 8 Calle 47 y 115, 1900 La Plata (Argentina)

2005-09-15

This study takes into consideration an analysis of the chemical polycyclic aromatic hydrocarbon (PAH) profile and its distribution in inhalable and respirable particulate matter in urban and industrial areas in La Plata, Argentina, and Leipzig, Germany. Representative samples from three locations in La Plata (industrial, traffic influenced and control area) and two locations in Leipzig (traffic influenced and control area) were obtained in summer and winter. The sampling of particulate matter was carried out with high volume collectors using cascade impactors to separate six size fractions. PAHs were extracted with hexane through a solid-liquid equilibrium extraction and analysed by HPLC/UV/fluorescence detection. The results showed a PAH seasonal behaviour in both regions, with lower contents in summer and higher ones in winter. Highest concentrations of total PAHs were found in the industrial area in La Plata. The size distribution of particles demonstrates the greater relevance of smaller particles. More than 50% of PAHs were associated with particles of less than 0.49 {mu}m. Moreover, this particle size fraction was associated with traffic, whereas other sources of combustion were related also to particles between 0.49 and 0.95 {mu}m. Considering the ratio of benzo(ghi)perylene (BgP)/benzo(a)pyrene (BaP) as an indicator for traffic influence, it was observed that La Plata City was more affected than Leipzig by the same proportion in summer and in winter. The BgP/InP (indeno(123-cd)pyrene) ratio was lower in winter than in summer in both places and indicates the presence of domestic combustion sources. It is important to point out the significance of using fingerprint compound ratios to identify possible sources of pollution with PAHs bound to particles.

Ambient air quality at the wider area of an industrial mining facility at Stratoni, Chalkidiki, Greece.

Science.gov (United States)

Gaidajis, Georgios; Angelakoglou, Komninos; Gazea, Emmy

2012-01-01

To assess ambient air quality at the wider area of a mining-industrial facility in Chalkidiki, Greece, the particulate matter with an aerodynamic diameter of 10 μm (PM(10)) and its content in characteristic elements, i.e., As, Cd, Cu, Fe, Mn, Pb, Zn were monitored for a period of three years (2008-2010). Gravimetric air samplers were employed for the particulate matter sampling at three sampling stations located in the immediate vicinity of the industrial facility and at a neighbouring residential site. Monitoring data indicated that the 3-year median PM(10) concentrations were 23.3 μg/m(3) at the residential site close to the facility and 28.7 μg/m(3) at the site within the facility indicating a minimal influence from the industrial activities to the air quality of the neighbouring residential area. Both annual average and median PM(10) concentration levels were below the indicative European standards, whereas similar spatial and temporal variation was observed for the PM(10) constituents. The average Pb concentrations measured for the three sampling sites were 0.2, 0.146 and 0.174 μg/m(3) respectively, well below the indicative limit of 0.5 μg/m(3). The quantitative and qualitative comparison of PM(10) concentrations and its elemental constituent for the three sampling stations did not indicate any direct influence of the mining-industrial activities to the air quality of the Stratoni residential area.

THE INFORMATION AND COMMUNICATION TECHNOLOGY – IMPACT ON THE HOSPITALITY INDUSTRY IN ROMANIA

OpenAIRE

Daniela FIROIU; Adina Gabriela CROITORU

2015-01-01

In the context of an increasingly dynamic society, globalization has become one of the key issues, causing important changes in the evolution of all economic sectors and especially in the development of the tourism industry, an industry that depends heavily on the free movement of people and unhindered access to information. Although the implications of the globalization phenomenon on tourism are extremely diverse and profound, sometimes difficult to commensurate, the evolution of the informa...

Fitting Irregular Shape Figures into Irregular Shape Areas for the Nesting Problem in the Leather Industry

Directory of Open Access Journals (Sweden)

Guevara-Palma Luis

2015-01-01

Full Text Available The nesting problem of irregular shapes within irregular areas has been studied from several approaches due to their application in different industries. The particular case of cutting leather involves several restrictions that add complexity to this problem, it is necessary to generate products that comply with the quality required by customers This paper presents a methodology for the accommodation of irregular shapes in an irregular area (leather considering the constraints set by the footwear industry, and the results of this methodology when applied by a computer system. The scope of the system is to develop a working prototype that operates under the guidelines of a commercial production line of a sponsor company. Preliminary results got a reduction of 70% of processing time and improvement of 5% to 7% of the area usage when compared with manual accommodation.

Blood lead level studies by the Public Health Service in an industrial stress area

Energy Technology Data Exchange (ETDEWEB)

Jantzen, G.

1981-12-01

The general directions of the European Community concerning lead resulted to be useful for analysing the biologic impact on the population living in an industrial immission area and for differentiating within this locality affected and non-affected residential districts. Consequently the social-hygienic and regional-hygienic measures are limited and justified territorially. The environmental parameters, their relation to the distance at which an industrial plant is situated and the blood lead values are indicated. Recommendations are given, which concern the protection of health and even the reconstruction of the residential area by immission-reducing measures. It was found that the lead impact on children is higher than that on grown-ups. Tables illustrate the symptomatology of lead impacts, its relation to blood lead concentration, the degree of impact measured in children and grown-ups and the corresponding necessary measures as auxiliary methods for the Public Health Service and the physicians.

Geochemical study of urban soils in public areas of an industrialized town (Ajka, western Hungary)

Science.gov (United States)

Zacháry, D.; Jordán, Gy.; Szabó, Cs.

2012-04-01

Soil is one of the most essential parts of urban ecosystem contributing to the biogeochemical cycles along the rock-soil-plant-animal and human pathway. Soil plays a fundamental role in plant nutrient uptake and groundwater filtration, too. Urban soils differ from non-urban soils in many aspects, including their origin, and they may also concentrate contaminants in large quantities due to intensive human activities. The pollution sources are industry, traffic, fertilizer, tailing and waste. In addition to the increasing rate of urban areas, urban soils are under growing interest and their pollution have received significant attention in the past few decades. This work focuses on the toxic element (As, Hg, Pb, Cu, Zn, Cd, Ni) content of soils and their spatial distribution in order to find a link between contamination sources and the receiving urban soils at sensitive receptor locations such as children's playgrounds and parks. Ajka town is located in western Hungary. It has an old-established industrial history with multiple contamination sources of heavy alumina industry and coal-based power plants supplied by the nearby bauxite and coal mines. At 44 locations 46 soil samples have been collected at a depth of 0-10 cm along a 1x1 km grid. The whole grid covers an area of 48 km2. In each grid cell a sampling site was selected at public areas. Sample preparation included drying at 40 C°, thorough homogenization and sieving to 2 mm fine earth before chemical analysis. Grain size distribution and soil pH were also determined. Samples were analyzed with ICP-OES and SEM methods. The As, Hg, Pb, Cu, Zn, Cd and Ni concentrations range from 2.07 ppm to 9.48 ppm, 0.02 ppm to 2.84 ppm, 5.08 ppm to 35.74 ppm, 2.55 ppm to 47.78 ppm, 17.00 ppm to 91.00 ppm, 0.07 ppm to 0.61 ppm and 5.57 ppm to 32.09 ppm, respectively. The results revealed the contaminated areas associated with past industrial sites. This study also identified locations with considerable contamination at

Uncertainty in the Sphere of the Industry 4.0 – Potential Areas to Research

Directory of Open Access Journals (Sweden)

Andrzej Magruk

2016-12-01

Full Text Available The world stands on the threshold of a new age of technology, which will launch a fourth industrial revolution (Industry 4.0. According to this idea, web-based network will support smart factories at every stage of the work on the product, from design through to servicing and recycling. It is a vision of a world in which the real environment connects to the digital one using follows driving forces: Internet of things, cloud computing, big data, cyber-physical systems, and others. The Industry 4.0 concept is based on developing smart chains preparation based on communicating with each other means of production, products, components, plants, humans. Established in Germany, the concept of Industry 4.0, is the brainchild – its beginning reaches 2011. It is therefore fraught with high level of uncertainty in many aspects (economic, social, technological, legal, etc.. The main aim of this article is to analyze different dimensions of uncertainty regarding the Industry 4.0, both in terms of opportunities and threats. Due to the freshness of the topic and the great complexity of the Industry 4.0 phenomenon, the main aim of the article is to identify potential areas requiring the necessary research in order minimizing negative – today uncertain – effects occurring in both the design concept Industry 4.0 as well as during its functioning.

AN AMELIORATED DETECTION STATISTICS FOR ADAPTIVE MASK MEDIAN FILTRATION OF HEAVILY NOISED DIGITAL IMAGES

Directory of Open Access Journals (Sweden)

Geeta Hanji

2016-11-01

Full Text Available Noise reduction is an important area of research in image processing applications. The performance of the digital image noise filtering method primarily depends upon the accuracy of noise detection scheme. This paper presents an effective detector based, adaptive mask, median filtration of heavily noised digital images affected with fixed value (or salt and pepper impulse noise. The proposed filter presents a novel approach; an ameliorated Rank Ordered Absolute Deviation (ROAD statistics to judge whether the input pixel is noised or noise free. If a pixel is detected as corrupted, it is subjected to adaptive mask median filtration; otherwise, it is kept unchanged. Extensive experimental results and comparative performance evaluations demonstrate that the proposed filter outperforms the existing decision type, median based filters with powerful noise detectors in terms of objective performance measures and visual retrieviation accuracy.

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan.

Science.gov (United States)

Azam, Iqra; Afsheen, Sumera; Zia, Ahmed; Javed, Muqaddas; Saeed, Rashid; Sarwar, Muhammad Kaleem; Munir, Bushra

2015-01-01

To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn) in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia), an acridid grasshopper (Oxya hyla hyla), and a nymphalid butterfly (Danaus chrysippus) near industrial zone of Gujrat. Accumulation of Cd was highest in insect species followed by Cu, Cr, Zn, and Ni at p Lepidoptera. The total metal concentrations in insects were pointed significantly higher at sites S3 (Mid of HalsiNala), S9 (End of HalsiNala), and S1 (Start of HalsiNala), whereas lowest value was detected at site S6 (Kalra Khasa) located far from industrial area. HACA indicates that these insect groups are potential indicators of metal contamination and can be used in biomonitoring.

THE SCENIC VALUE OF ABANDONED MINING AREAS IN POLAND

Directory of Open Access Journals (Sweden)

URSZULA MYGA-PIĄTEK

2008-12-01

Full Text Available Abandoned Polish mining areas are commonly heavily transformed so that they endanger no longer the environment. A disadvantage is that the newly created areas commonly contribute to the monotonous urban-industrial landscape, rather than providing additional value. This is partly due to legislation that hampers a more diversified management of abandoned mining areas as potentially valuable landforms. One of the legal barriers that restricts the possibilities of making these areas more attractive, regards the utilization of remaining exploitation holes (i.e. land depressions of at least 2 m deep, formed as a result of open-pit mining of energy, chemical, building or metallurgical resources and waste heaps as important cultural and scenic elements. Such a new use of these old mininginduced phenomena is important if it is intended not only to involve the regional population in the process of exploring and exploiting the earth’s resources, but also to confront them with some negative consequences of these activities, including shaping the landscape in which these objects are situated. The current attitude towards a new architecture for abandoned mining areas should be reconsidered; particularly the present-day approach based on narrow specializations – for instance of experts in mineral exploitation, spatial planning or environmental protection – should be replaced by interdisciplinary action regarding shaping the landscape of abandoned mining areas.

Identification of soybean genotypes adaptive to tropical area and suitable for industry

Science.gov (United States)

Adie, M. M.; Krisnawati, A.

2018-01-01

Soybeans in Indonesia are mostly used for raw material of tempeh industry. This study aims to identify 150 soybean genotypes for their suitability for raw materials of tempeh and adaptability to be developed in tropical area of Indonesia. The research material consisted of 150 soybean genotypes. The field research was conducted in Malang from February to May 2016, using a randomized block design with two replicates. The identification of 150 soybean genotypes showed 30.67% of super early maturity (soybeans with large seed size. In this research, G511H/Anj//Anj////Anjs-8-5 was suitable to be developed in Indonesia’s tropical climate and also preferred by industry for tempeh raw material due to its high yield, super early days to maturity, and large seed size.

Rare earth industries: Strategies for Malaysia

International Nuclear Information System (INIS)

2011-01-01

Evidently, many reports cite Malaysia as having reasonably substantial amounts of rare earths elements. In fact, based on the rare earths found in the residual tin deposits alone, Malaysia has about 30,000 tonnes. This does not take into account unmapped deposits which experts believe may offer more tonnages of rare earths. Brazil which is reported to have about 48,000 tonnes has announced plans to invest aggressively in the rare earths business. China has on record the largest reserves with about 36 million tonnes. This explains why China has invested heavily in the entire value chain of the rare earths business. Chinas committed investment in rare earths started many years ago when the country's foremost leaders proclaimed the strategic position of rare earths in the world economy. That forecast is now a reality where the rise in the green high-tech economy is seen driving global demand for rare earths in a big way. Malaysia needs to discover and venture into new economic growth areas. This will help fuel the country's drive to achieve a high income status by 2020 as articulated in the New Economic Model (NEM) and the many supporting Economic Transformation Plans that the Government has recently launched. Rare earths may be the new growth area for Malaysia. However, the business opportunities should not just be confined to the mining, extraction and production of rare earths elements alone if Malaysia is to maximise benefits from this industry. The industry's gold mine is in the downstream products. This is also the sector that China wants to expand. Japan which now controls about 50 % of the global market for downstream rare earths-based high-tech components is desperately looking for partners to grow their stake in the business. Malaysia needs to embark on the right strategies in order to build the rare earths industry in the country. What are the strategies? (author)

AREAS OF ECONOMIC INFLUENCE OF SUGARCANE INDUSTRY IN MATO GROSSO, 2010.

Directory of Open Access Journals (Sweden)

Wladimir Colman de Azevedo Junior

2015-09-01

Full Text Available The Macroeconomic data reveals the increase of sugarcane chain relevance to Mato Grosso economy, however does not exist studies that evaluate the scope of regional impacts. This research has as the main objective the identification of the territory extension of the sugarcane industry influence in Mato Grosso during 2010, characterizing relationships between industrial plants and the regions where they acting. Was used the gravitational model developed by Isard (1956 to estimate this interrelation commerce patterns of the chain in the state, to find the sugarcane regional centers, as well as, to set up their potential areas of influence. As results has the identification of the 13 cane regions, three cities in first level, seven in the second level and three sub-centers. The relations between this centers and the respective regions has different specifications and their complete understanding allows destination of private investments and public politics. Keywords: Gravitational Model. Cane Sugar Suply Chain. Mato Grosso.

The Role of Context in Academic Capitalism: The Industry-Friendly Department Case

Science.gov (United States)

Mendoza, Pilar

2012-01-01

This study shows a case of a department heavily involved in industry-academia collaborations and patenting activities while exhibiting high levels of academic norms such as teaching, basic research, academic freedom and free dissemination of knowledge. Based on the findings, the author argues that academic capitalism is a highly contextual…

Solid phase speciation of arsenic by sequential extraction in standard reference materials and industrially contaminated soil samples

International Nuclear Information System (INIS)

Herreweghe, Samuel van; Swennen, Rudy; Vandecasteele, Carlo; Cappuyns, Valerie

2003-01-01

Leaching experiments, a mineralogical survey and larger samples are preferred when arsenic is present as discrete mineral phases. - Availability, mobility, (phyto)toxicity and potential risk of contaminants is strongly affected by the manner of appearance of elements, the so-called speciation. Operational fractionation methods like sequential extractions have been applied for a long time to determine the solid phase speciation of heavy metals since direct determination of specific chemical compounds can not always be easily achieved. The three-step sequential extraction scheme recommended by the BCR and two extraction schemes based on the phosphorus-like protocol proposed by Manful (1992, Occurrence and Ecochemical Behaviours of Arsenic in a Goldsmelter Impacted Area in Ghana, PhD dissertation, at the RUG) were applied to four standard reference materials (SRM) and to a batch of samples from industrially contaminated sites, heavily contaminated with arsenic and heavy metals. The SRM 2710 (Montana soil) was found to be the most useful reference material for metal (Mn, Cu, Zn, As, Cd and Pb) fractionation using the BCR sequential extraction procedure. Two sequential extraction schemes were developed and compared for arsenic with the aim to establish a better fractionation and recovery rate than the BCR-scheme for this element in the SRM samples. The major part of arsenic was released from the heavily contaminated samples after NaOH-extraction. Inferior extraction variability and recovery in the heavily contaminated samples compared to SRMs could be mainly contributed to subsample heterogeneity

The impact of industrial anthropization on mosquito (Diptera, Culicidae) communities in mangrove areas of Guanabara Bay (Rio de Janeiro, Brazil).

Science.gov (United States)

de Souza, A S; Couri, M S; Florindo, L

2012-02-01

The effects of industrial anthropization on species composition and community diversity of Culicidae (Diptera) were studied in a mangrove area impacted by industrial activities as compared to a preserved area, both around Guanabara Bay in the state of Rio de Janeiro, Brazil. Diversity, equitability, and species richness in Culicidae community differed between the studied areas. Indicator species analysis and correspondence analysis were carried out and indicated that the Sabethini, especially Wyeomyia (Phoniomyia) theobaldi Lane, Wyeomyia (Phoniomyia) fuscipes (Edwards), and a non-identified species of Wyeomyia sp. were associated to the preserved area, whereas Aedes taeniorhynchus Wiedemann and Aedes scapularis (Rondani) to the impacted area.

Voluntary agreements in the industrial sector in China

Energy Technology Data Exchange (ETDEWEB)

Price, Lynn; Worrell, Ernst; Sinton, Jonathan

2003-03-31

China faces a significant challenge in the years ahead to continue to provide essential materials and products for a rapidly-growing economy while addressing pressing environmental concerns. China's industrial sector is heavily dependent on the country's abundant, yet polluting, coal resources. While tremendous energy conservation and environmental protection achievements were realized in the industrial sector in the past, there remains a great gulf between the China's level of energy efficiency and that of the advanced countries of the world. Internationally, significant energy efficiency improvement in the industrial sector has been realized in a number of countries using an innovative policy mechanism called Voluntary Agreements. This paper describes international experience with Voluntary Agreements in the industrial sector as well as the development of a pilot program to test the use of such agreements with two steel mills in Shandong Province, China.

A statistical approach to rank multiple priorities in Environmental Epidemiology: an example from high-risk areas in Sardinia, Italy

Directory of Open Access Journals (Sweden)

Dolores Catelan

2008-11-01

Full Text Available In Environmental Epidemiology, long lists of relative risk estimates from exposed populations are compared to a reference to scrutinize the dataset for extremes. Here, inference on disease profiles for given areas, or for fixed disease population signatures, are of interest and summaries can be obtained averaging over areas or diseases. We have developed a multivariate hierarchical Bayesian approach to estimate posterior rank distributions and we show how to produce league tables of ranks with credibility intervals useful to address the above mentioned inferential problems. Applying the procedure to a real dataset from the report “Environment and Health in Sardinia (Italy” we selected 18 areas characterized by high environmental pressure for industrial, mining or military activities investigated for 29 causes of deaths among male residents. Ranking diseases highlighted the increased burdens of neoplastic (cancerous, and non-neoplastic respiratory diseases in the heavily polluted area of Portoscuso. The averaged ranks by disease over areas showed lung cancer among the three highest positions.

Benchmarking of Governmental Support Measures for University-Industry Cooperation

Directory of Open Access Journals (Sweden)

Kärt Rõigas

2013-01-01

Full Text Available This paper aims to benchmark Estonian governmental support measures targeted toward enhancing university-industry collaboration to European best practice and make suggestions for the development of these measures. The intensity and scope of university-industry cooperation support measures varies heavily in Europe. The survey of European University-Business Cooperation, Pro Inno Europe and Erawatch database of policy measures, and Community Innovation Survey reveal that Finnish, German and Austrian support systems are best balanced and provide good university-industry cooperation intensity. The cooperation measures in Estonia are weak and improvement should be made by increasing the Estonian governmental funding, mandatory cooperation in support measures, networking and applied research in universities, on-going application possibilities, reducing the bureaucracy, and improving the timing of measures.

Ameliorating effects of industrial sugar residue on the Jales gold mine spoil (NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators

Energy Technology Data Exchange (ETDEWEB)

Bleeker, P.M.; Teiga, P.M.; Santos, M.H.; Koe, T. de; Verkleij, J.A.C

2003-09-01

A residue of the sugar industry can be used in revegetation programs on metal contaminated sites. - Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste product of the sugar industry, proved to ameliorate spoils conditions for plant performance by elevating pH and immobilising several metals. Although arsenate concentrations were positively correlated to spoil pH and spoil treatment with ISR mobilised As, growth of both Phaseolus vulgaris and Holcus lanatus improved significantly after applications of 3.75 g ISR kg{sup -1} dry spoil. Nutrient uptake from the substrate, with the exception of potassium, was elevated by ISR. As a remediation technique ISR application could be effective although in As-contaminated sites application might be restricted to areas where leaching to (ground) water does not form a risk.

Polybrominated diphenyl ethers in soils, sediments, and human hair in a plastic waste recycling area: a neglected heavily polluted area.

Science.gov (United States)

Tang, Zhenwu; Huang, Qifei; Cheng, Jiali; Yang, Yufei; Yang, Jun; Guo, Wei; Nie, Zhiqiang; Zeng, Ning; Jin, Lu

2014-01-01

The release of pollutants during the recycling of contaminated plastics is a problem which has drawn worldwide attention; however, little information on the transfer of polybrominated diphenyl ethers (PBDEs) in these processes is available. We conducted a survey of PBDEs in soils, sediments, and human hair in a typical plastic waste recycling area in northern China. The total concentrations (ng/g) of 21 PBDEs were 1.25-5504 (average 600), 18.2-9889 (average 1619), and 1.50-861 (average 112) in soils, sediments, and hair, respectively. The PBDE concentrations were comparable to concentrations observed in e-waste recycling areas; however, the concentrations in soils and sediments were 1-3 orders of magnitude higher than in other areas, and the concentrations in hair were much higher than in other areas. This indicates that this area is highly polluted with PBDEs. BDE-209 was the dominant congener (representing 91.23%, 92.3%, and 91.5% of the total PBDEs observed in soils, sediments, and hair, respectively), indicating that the commercial deca-BDE product was dominant. The commercial penta- and octa-BDE products made small contributions to the total PBDE concentrations, unlike what has been found in some e-waste recycling areas. Our results show that crude plastic waste processing is a major contributor of PBDEs to the environment and humans, which should be of great concern.

Assessment of Respiratory Function in Students, Residing in Different Industrial Areas

Directory of Open Access Journals (Sweden)

Aiman E. Konkabaeva

2013-01-01

Full Text Available The article considers the results of the examination of three groups of apparently healthy volunteer students of one social group, both men and women, without bad habits, aged 19-22. Students live in three different industrial areas of Central Khazakhstan, containing ironworks (Temirtau and non-ferrous smelters (Balkhash, Zhezkazgan. It determined the necessity of respiratory function examination, using automated lung tester. The examination of respiratory function determined the decrease of the following parameters: lung vital capacity, maximal expiratory flow volume, forced expiratory volume 1, peak expiratory flow rate, cardiac minute output 25-50 if compared to proper parameters. The examination enabled us to make the conclusion that respiratory function is restricted due to high respiratory load, caused by air pollution. Changes intensity is different and can indicate the pollution in the examined areas.

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan

Directory of Open Access Journals (Sweden)

Iqra Azam

2015-01-01

Full Text Available To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia, an acridid grasshopper (Oxya hyla hyla, and a nymphalid butterfly (Danaus chrysippus near industrial zone of Gujrat. Accumulation of Cd was highest in insect species followed by Cu, Cr, Zn, and Ni at p<0.05. Hierarchical cluster analysis (HACA was carried out to study metal accumulation level in all insects. Correlation and regression analysis confirmed HACA observations and declared concentration of heavy metals above permissible limits. Metal concentrations in insects were significantly higher near industries and nallahs in Gujrat and relatively higher concentrations of metals were found in Orthoptera than Odonata and Lepidoptera. The total metal concentrations in insects were pointed significantly higher at sites S3 (Mid of HalsiNala, S9 (End of HalsiNala, and S1 (Start of HalsiNala, whereas lowest value was detected at site S6 (Kalra Khasa located far from industrial area. HACA indicates that these insect groups are potential indicators of metal contamination and can be used in biomonitoring.

Flared gases and other pollutants associated with air quality in industrial areas of Nigeria: an overview.

Science.gov (United States)

Osuji, Leo C; Avwiri, Greg O

2005-10-01

Nigeria, like any other developing nation, is faced with the twin problem of development without destruction. Industrialization, though an important component of development, has had a large share in the despoilation of air quality in the country by the release of high amounts of pollutants into the atmosphere. Petroleum hydrocarbons from refineries, flared gases, dusts, and fumes of metal-smelting and cement works, odorous gases of chemical and allied industries, carbon monoxide and oxides of sulfur and nitrogen of internal combustion engines, the charred particulates and sulfur dioxide emissions of the steel industries etc., all constitute pollutants or co-pollutants of the Nigerian atmosphere. This review article gives an insight into the phenomenal concentrations of some of these pollutants in the Nigerian atmosphere, which point to their unsafe levels and concomitant health risks. It is against this background that there should be continuous but sound monitoring exercise of the Nigerian environment, devoid of the peculiar mix of politics and science, in order to properly audit the quality of air, especially in areas of heavy industrial pollution. Such checks and balances would provide empirical data to assess the various trade-offs of atmospheric pollution in industrial areas of the country such as the Niger Delta region where oil and gas are produced. There should also be enforcement, thereof, of all existing and/or revised standards or regulations such as the compliance limits of the Department of Petroleum Resources (DPR) or the erstwhile Federal Environmental Protection Agency (FEPA).

NuSTAR observations of heavily obscured quasars at z ~ 0.5

DEFF Research Database (Denmark)

Lansbury, G. B.; Alexander, D. M.; Del Moro, A.

2014-01-01

We present NuSTAR hard X-ray observations of three Type 2 quasars at z ≈ 0.4-0.5, optically selected from the Sloan Digital Sky Survey. Although the quasars show evidence for being heavily obscured, Compton-thick systems on the basis of the 2-10 keV to [O III] luminosity ratio and multiwavelength...

The '333' integrated strategy for effective pollution control and its application to the heavily polluted Jialu River in north China.

Science.gov (United States)

Huang, Yu; Sun, Jie; Li, Aimin; Xie, Xianchuan

2018-05-01

In this study, an integrated approach named the '333' strategy was applied to pollution control in the Jialu River, in northern China, which is heavily burdened with anthropogenic pollution. Due to a deficiency of the natural ecological inflow, the Jialu River receives predominantly industrial and municipal effluent. The '333' strategy is composed of three steps of pollution control including industrial point-source pollution control, advanced treatment of municipal wastewater, and ecological restoration; three increased stringency emission standards; and three stages of reclamation. Phase 1 of the '333' strategy focuses on industrial point-source pollution control; phase 2 aims to harness municipal wastewater and minimize sewage effluents using novel techniques for advanced water purification; phase 3 of the '333' strategy focuses on the further purification of effluents flowing into Jialu River with the employment of an engineering-based ecological restoration project. The application of the '333' strategy resulted in the development of novel techniques for water purification including modified magnetic resins (NDMP resin), a two-stage internal circulation anaerobic reactor (IC reactor) and an ecological restoration system. The results indicate that water quality in the river was significantly improved, with increased concentrations of dissolved oxygen (DO), as well as reduction of COD by 42.8% and NH 3 -N by 61.4%. In addition, it was observed that the total population of phytoplankton in treated river water notably increased from only one prior to restoration to 8 following restoration. This system also provides a tool for pollution control of other similar industrial and anthropogenic source polluted rivers.

23 CFR 750.706 - Sign control in zoned and unzoned commercial and industrial areas.

Science.gov (United States)

2010-04-01

... TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT HIGHWAY BEAUTIFICATION Outdoor Advertising Control § 750.706 Sign... spacing of outdoor advertising signs located in commercial or industrial zoned or unzoned areas, as... back-to-back or “V” type signs. (c) Where the agreement and State law permits control by local zoning...

Voluntary agreements for increasing energy-efficiency in industry: Case study of a pilot project with the steel industry in Shandong Province, China

Energy Technology Data Exchange (ETDEWEB)

Price, Lynn; Worrell, Ernst; Sinton, Jonathan; Yun, Jiang

2003-03-01

China faces a significant challenge in the years ahead to continue to provide essential materials and products for a rapidly-growing economy while addressing pressing environmental concerns. China's industrial sector is heavily dependent on the country's abundant, yet polluting, coal resources. While tremendous energy conservation and environmental protection achievements were realized in the industrial sector in the past, there remains a great gulf between the China's level of energy efficiency and that of the advanced countries of the world. Internationally, significant energy efficiency improvement in the industrial sector has been realized in a number of countries using an innovative policy mechanism called Voluntary Agreements. This paper describes international experience with Voluntary Agreements in the industrial sector as well as the development of a pilot program to test the use of such agreements with two steel mills in Shandong Province, China.

Low temperature industrial waste heat utilization in the area 'Speyer-Ludwigshafen-Frankenthal-Worms'

International Nuclear Information System (INIS)

Nunold, K.; Krebs, A.

1982-01-01

The aim of the study is the elaboration of reliable facts whether and under which conditions low temperature industrial waste heat systems can be economically utilized for heating purposes. The source of the waste heat are power- and industrial plants. In order to obtain reliable results, investigations have been carried out in the area Speyer-Ludwigshafen-Frankenthal and Worms. These investigations showed a number of application possibilities for heat pumps and it became moreover evident that there is a high variaiton of the heat requirement due to social components and the different type of building structures of the consumers. The economic results showed that the application of this heating system can under certain conditions supplement resp. replace other heating systems. (orig.) [de

Do the VOCs that evaporate from a heavily polluted river threaten the health of riparian residents?

International Nuclear Information System (INIS)

Juang, Der-Fong; Lee, Chao-Hsien; Chen, Wei-Chin; Yuan, Chung-Shin

2010-01-01

To understand the potential threat of volatile organic compounds (VOCs) to the health of residents living close to a heavily polluted river, this study investigated the species and the concentration of VOCs evaporating from a river and surveyed the health condition of the nearby residents. Air samples were taken seasonally at the upstream, midstream, and downstream water surfaces of the river, and at different locations at certain distances from the river. These samples were analyzed qualitatively and quantitatively through gas chromatography and electron capture detector (GC/ECD) for chlorinated organic compounds, and through gas chromatography and flame ionization detector (GC/FID) for ordinary hydrocarbons. The health data obtained from valid health questionnaires of 908 residents were analyzed through Statistical Package for Social Science (SPSS) software. Twenty-six species of VOCs were identified in the environment adjacent the river, many of which are carcinogenic or believed to be carcinogenic to humans. However, results of this study shows that the VOCs evaporating from the polluted river have not been definitively identified as a major factor of cancer in the residents. However, the risk of suffering from certain chronic diseases may increase in residents living less than 225 m away from the river due to the high levels of evaporated VOCs. Residents living less than 225 m away from the river and with nearby specific industries are 3.130 times more at risk of suffering from chronic diseases than those with no nearby specific industries.

Peat wetland as a natural filter of effluents from adjacent industrial areas

OpenAIRE

József DEZSO; Gabriella TÓTH; Dénes LÓCZY

2015-01-01

The main objective of the project is the study of a peat wetland functioning as recipient of effluents from former and present-day industrial activities. The investigation was focused on heavy metal contaminations and their probable mobilization or fixation. The studied peatbog is a typical Eastern European wetland, located in Hungary on the border between medium mountains (Bakony Mountains) and a Neogene basin (the Sárrét, an area under nature conservation). Watercourses and prevailing air c...

Health effects of environmental pollution in population living near industrial complex areas in Korea.

Science.gov (United States)

Eom, Sang-Yong; Choi, Jonghyuk; Bae, Sanghyuk; Lim, Ji-Ae; Kim, Guen-Bae; Yu, Seung-Do; Kim, Yangho; Lim, Hyun-Sul; Son, Bu-Soon; Paek, Domyung; Kim, Yong-Dae; Kim, Heon; Ha, Mina; Kwon, Ho-Jang

2018-01-01

Several epidemiological studies have reported an association between environmental pollution and various health conditions in individuals residing in industrial complexes. To evaluate the effects of pollution from industrial complex on human health, we performed a pooled analysis of environmental epidemiologic monitoring data for residents living near national industrial complexes in Korea. The respiratory and allergic symptoms and the prevalence of acute and chronic diseases, including cancer, were used as the outcome variables for health effects. Multiple logistic regression analysis was used to analyze the relationship between exposure to pollution from industrial complexes and health conditions. After adjusting for age, sex, smoking status, occupational exposure, level of education, and body mass index, the residents near the industrial complexes were found to have more respiratory symptoms, such as cough (odds ratio [OR], 1.18; 95% confidence interval [CI], 1.06 to 1.31) and sputum production (OR, 1.13; 95% CI, 1.03 to 1.24), and symptoms of atopic dermatitis (OR, 1.10; 95% CI, 1.01 to 1.20). Among residents of the industrial complexes, the prevalence of acute eye disorders was approximately 40% higher (OR, 1.39; 95% CI, 1.04 to 1.84) and the prevalence of lung and uterine cancer was 3.45 times and 1.88 times higher, respectively, than those among residents of the control area. This study showed that residents living in the vicinity of industrial complexes have a high risk of acute and chronic diseases including respiratory and allergic conditions. These results can be used as basic objective data for developing health management measures for individuals residing near industrial complexes.

Health effects of environmental pollution in population living near industrial complex areas in Korea

Directory of Open Access Journals (Sweden)

Sang-Yong Eom

2018-01-01

Full Text Available Several epidemiological studies have reported an association between environmental pollution and various health conditions in individuals residing in industrial complexes. To evaluate the effects of pollution from industrial complex on human health, we performed a pooled analysis of environmental epidemiologic monitoring data for residents living near national industrial complexes in Korea. The respiratory and allergic symptoms and the prevalence of acute and chronic diseases, including cancer, were used as the outcome variables for health effects. Multiple logistic regression analysis was used to analyze the relationship between exposure to pollution from industrial complexes and health conditions. After adjusting for age, sex, smoking status, occupational exposure, level of education, and body mass index, the residents near the industrial complexes were found to have more respiratory symptoms, such as cough (odds ratio [OR], 1.18; 95% confidence interval [CI], 1.06 to 1.31 and sputum production (OR, 1.13; 95% CI, 1.03 to 1.24, and symptoms of atopic dermatitis (OR, 1.10; 95% CI, 1.01 to 1.20. Among residents of the industrial complexes, the prevalence of acute eye disorders was approximately 40% higher (OR, 1.39; 95% CI, 1.04 to 1.84 and the prevalence of lung and uterine cancer was 3.45 times and 1.88 times higher, respectively, than those among residents of the control area. This study showed that residents living in the vicinity of industrial complexes have a high risk of acute and chronic diseases including respiratory and allergic conditions. These results can be used as basic objective data for developing health management measures for individuals residing near industrial complexes.

Trace elements of concern affecting urban agriculture in industrialized areas: A multivariate approach.

Science.gov (United States)

Boente, C; Matanzas, N; García-González, N; Rodríguez-Valdés, E; Gallego, J R

2017-09-01

The urban and peri-urban soils used for agriculture could be contaminated by atmospheric deposition or industrial releases, thus raising concerns about the potential risk to public health. Here we propose a method to evaluate potential soil pollution based on multivariate statistics, geostatistics (kriging), a novel soil pollution index, and bioavailability assessments. This approach was tested in two districts of a highly populated and industrialized city (Gijón, Spain). The soils showed anomalous content of several trace elements, such as As and Pb (up to 80 and 585 mg kg -1 respectively). In addition, factor analyses associated these elements with anthropogenic activity, whereas other elements were attributed to natural sources. Subsequent clustering also facilitated the differentiation between the northern area studied (only limited Pb pollution found) and the southern area (pattern of coal combustion, including simultaneous anomalies of trace elements and benzo(a)pyrene). A normalized soil pollution index (SPI) was calculated by kriging, using only the elements falling above threshold levels; therefore point-source polluted zones in the northern area and diffuse contamination in the south were identified. In addition, in the six mapping units with the highest SPIs of the fifty studied, we observed low bioavailability for most of the elements that surpassed the threshold levels. However, some anomalies of Pb contents and the pollution fingerprint in the central area of the southern grid call for further site-specific studies. On the whole, the combination of a multivariate (geo) statistic approach and a bioavailability assessment allowed us to efficiently identify sources of contamination and potential risks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Diurnal, weekly and seasonal air concentrations of PCDD and PCDF in an industrial area

International Nuclear Information System (INIS)

Benfenati, E.; Mariani, G.; Schiavon, G.; Lodi, M.; Fanelli, R.

1994-01-01

Air samples were collected in an industrial area close to Milan in July and in November, day and night for five days and have been analyzed for PCDD and PCDF. Average summer levels were generally lower than winter levels, and average concentrations were higher by night than by day in both months. (orig.)

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan

OpenAIRE

Azam, Iqra; Afsheen, Sumera; Zia, Ahmed; Javed, Muqaddas; Saeed, Rashid; Sarwar, Muhammad Kaleem; Munir, Bushra

2015-01-01

To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn) in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia), an acridid grasshopper (Oxya hyla hyla), and a nymphalid butterfly (Danaus chrysippus) near industrial zone of Gujrat. Accumulation of Cd was highest in insec...

Tourism revenue as a conservation tool for threatened birds in protected areas.

Directory of Open Access Journals (Sweden)

Rochelle Steven

Full Text Available Many bird populations worldwide are at risk of extinction, and rely heavily on protected area networks for their continued conservation. Tourism to these areas contributes to conservation by generating revenue for management. Here we quantify the contribution of tourism revenue for bird species in the IUCN Red List, using a simple accounting method. Relevant data are available for 90 (16% of the 562 critically endangered and endangered species. Contributions of tourism to bird conservation are highest, 10-64%, in South America, Africa, and their neighbouring islands. Critically endangered bird species rely on tourism more heavily than endangered species (p<0.02. Many protected areas could also enhance their management budgets by promoting birdwatching tourism specifically.

Tourism Revenue as a Conservation Tool for Threatened Birds in Protected Areas

Science.gov (United States)

Steven, Rochelle; Castley, J. Guy; Buckley, Ralf

2013-01-01

Many bird populations worldwide are at risk of extinction, and rely heavily on protected area networks for their continued conservation. Tourism to these areas contributes to conservation by generating revenue for management. Here we quantify the contribution of tourism revenue for bird species in the IUCN Red List, using a simple accounting method. Relevant data are available for 90 (16%) of the 562 critically endangered and endangered species. Contributions of tourism to bird conservation are highest, 10–64%, in South America, Africa, and their neighbouring islands. Critically endangered bird species rely on tourism more heavily than endangered species (p<0.02). Many protected areas could also enhance their management budgets by promoting birdwatching tourism specifically. PMID:23667498

Landscape monitoring of post-industrial areas using LiDAR and GIS technology

Directory of Open Access Journals (Sweden)

Wężyk Piotr

2015-06-01

Full Text Available The quarrying industry is changing the local landscape, forming deep open pits and spoil heaps in close proximity to them, especially lignite mines. The impact can include toxic soil material (low pH, heavy metals, oxidations etc. which is the basis for further reclamation and afforestation. Forests that stand on spoil heaps have very different growth conditions because of the relief (slope, aspect, wind and rainfall shadows, supply of solar energy, etc. and type of soil that is deposited. Airborne laser scanning (ALS technology deliver point clouds (XYZ and derivatives as raster height models (DTM, DSM, nDSM=CHM which allow the reception of selected 2D and 3D forest parameters (e.g. height, base of the crown, cover, density, volume, biomass, etc. The automation of ALS point cloud processing and integrating the results into GIS helps forest managers to take appropriate decisions on silvicultural treatments in areas with failed plantations (toxic soil, droughts on south-facing slopes; landslides, etc. or as regular maintenance. The ISOK country-wide project ongoing in Poland will soon deliver ALS point cloud data which can be successfully used for the monitoring and management of many thousands of hectares of destroyed post-industrial areas which according to the law, have to be afforested and transferred back to the State Forest.

Guidelines for integrated risk assessment and management in large industrial areas. Inter-Agency programme on the assessment and management of health and environmental risks from energy and other complex industrial systems

International Nuclear Information System (INIS)

1998-01-01

The IAEA, the United Nations Environment Programme (UNEP) within the framework of the Awareness and Preparedness for Emergencies at Local Level (APELL), the United Nations Industrial Development Organization (UNIDO) and the World Health Organization (WHO) decided in 1986 to join forces in order to promote the use of integrated area wide approaches to risk management. An Inter-Agency Programme, which brings together expertise in health the environment, industry and energy, all vital for effective risk management, was established. The Inter-Agency Programme on the assessment and Management of Health and Environmental Risks from Energy and Other Complex Industrial Systems aims at promoting and facilitating the implementation of integrated risk assessment and management for large industrial areas. This initiative includes the compilation of procedures and methods for environmental and public health risk assessment, the transfer of knowledge and experience amongst countries in the application of these procedures and the implementation of an integrated approach to risk management. The purpose of the Inter-Agency Programme is to develop a broad approach to the identification, prioritization and minimization of industrial hazards in a given geographical area. The UN organizations sponsoring this programme have been involved for several years in activities aimed at assessment and management of environmental and health risks, prevention of major accidents and emergency preparedness. These Guidelines have been developed on the basis of experience from these activities to assist in the planning and conduct of regional risk management projects. They provide a reference framework for the undertaking of integrated health and environmental risk assessment for large industrial areas and for the formulation of appropriate risk management strategies

Guidelines for integrated risk assessment and management in large industrial areas. Inter-Agency programme on the assessment and management of health and environmental risks from energy and other complex industrial systems

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

The IAEA, the United Nations Environment Programme (UNEP) within the framework of the Awareness and Preparedness for Emergencies at Local Level (APELL), the United Nations Industrial Development Organization (UNIDO) and the World Health Organization (WHO) decided in 1986 to join forces in order to promote the use of integrated area wide approaches to risk management. An Inter-Agency Programme, which brings together expertise in health the environment, industry and energy, all vital for effective risk management, was established. The Inter-Agency Programme on the assessment and Management of Health and Environmental Risks from Energy and Other Complex Industrial Systems aims at promoting and facilitating the implementation of integrated risk assessment and management for large industrial areas. This initiative includes the compilation of procedures and methods for environmental and public health risk assessment, the transfer of knowledge and experience amongst countries in the application of these procedures and the implementation of an integrated approach to risk management. The purpose of the Inter-Agency Programme is to develop a broad approach to the identification, prioritization and minimization of industrial hazards in a given geographical area. The UN organizations sponsoring this programme have been involved for several years in activities aimed at assessment and management of environmental and health risks, prevention of major accidents and emergency preparedness. These Guidelines have been developed on the basis of experience from these activities to assist in the planning and conduct of regional risk management projects. They provide a reference framework for the undertaking of integrated health and environmental risk assessment for large industrial areas and for the formulation of appropriate risk management strategies. Refs, figs, tabs.

Applying Technology Management concepts in analyzing e Waste, sustainability and technology development in Mobile Industry: A conceptual perspective

OpenAIRE

Lasrado, Lester Allan; Agnihothri, Subodh; Lugmayr, Artur

2013-01-01

In the highly globalized, competitive and technocrat world, mobile industry is heavily focused on making itself sustainable. In order to achieve this focus should be on improving the e waste management in the industry. Currently the industry is advanced beyond market demand in delivery services to customers in terms of ICT and smart phones. This research paper is trying to conceptualize the aspect of technology management by comparing technology advancement of mobile phone technology and the ...

Tax Responses in Platform Industries

DEFF Research Database (Denmark)

Kind, Hans Jarle; Köthenbürger, Marko; Schjelderup, Guttorm

that a higher ad valorem tax may undermine a firm's incentive to differentiate its product from that of its competitors. Finally, we demonstrate that the effects of increasing specific taxes may be the opposite of those of increasing value added taxes....... price and thus buy less of the good. The present paper shows that this result need not hold in a two-sided market. On the contrary, a higher ad valorem tax may lower end-user prices and spur sales. Thus, two-sided platform firms may not at all engage in tax shifting via price increases. We further show......Two-sided platform firms serve distinct customer groups that are connected through interdependent demand, and include major businesses such as the media industry, banking, and the software industry. A well known result of tax incidence is that consumers of a more heavily taxed good pay a higher...

Intensifying waste water clarification in heavy and mining industries for sanitation of rivers in the Katowice district

Energy Technology Data Exchange (ETDEWEB)

Paluch, J.; Twardowska, I.

1976-01-01

This article presents a detailed account of the state of water pollution in the main and tributary rivers of the heavily populated and industrialized district of Katowice, Poland: Results of surveys in the years 1969 to 1972 are given. Several tables and maps show the degree of water pollution in rivers, the amount to which the values exceed pollution standards, percentage of treated and untreated industrial waste water entering the rivers, the classification of river sections according to their content of suspensions, phenols and salt. Further figures show the effectiveness of water cleaning flocculating agents and of waste water treatment at coking plants. Black coal mining and processing contributes the greater part to pollution of the rivers. Only 54% of mining industry waste water is cleaned mechanically and 3% chemically. The amount of 3,300 t/d of chlorite and sulfate salts is led into the rivers primarily from the Rybnik coal mining area. The clarification of waste water resulting from hydraulic stowing and from flotation processes is described as most problematic. Research efforts are being made at economic desalination and suspension flocculation. In the coking industry waste water is treated in 88% of the plants, but dephenolization takes place in only 50% of the plants. (29 refs.) (In German)

Analysis of PAEs contaminants in water sources for agriculture, industrial and residential areas from local city district

Science.gov (United States)

Chen, Qidan; Chen, Qixian; Wu, Fei; Liao, Jia; Zhao, Xi

2018-02-01

The technology of DEHP and DBP detection by high performance liquid chromatography coupled with ultraviolet detection (HPLC-UV) was developed and applied in analysis of local water sources from agriculture, industrial and residential areas. Under the optimized sample pretreatment and detection conditions, DEHP and DBP were well separated and detected in 4 mins. The detection limit of DBP was 0.002 mg/L and DEHP was 0.006 mg/L, and it meets the Chinese National Standard limitations for drinking water quality. The linear correlation coefficient of DBP and DEHP standard calibration curves was 0.9998 and 0.9995. The linear range of DBP was 0.020 mg/L ∼20.0 mg/L, with the standard deviation of 0.560% ∼5.07%, and the linear range of DEHP was 0.060 mg/L ∼15.0 mg/L, with the standard deviation of 0.546% ∼5.74%. Ten water samples from Jinwan district of Zhuhai in Guangdong province of China were analyzed. However, the PAEs amounts found in the water sources from industrial areas were higher than the agriculture and residential areas, industries grow incredibly fast in the district in recently years and more attention should be paid to the increasing risks of water sources pollution.

Bioaccumulation of selected heavy metals and histopathological and hematobiochemical alterations in backyard chickens reared in an industrial area, India.

Science.gov (United States)

Kar, Indrajit; Mukhopadhayay, Sunit Kumar; Patra, Amlan Kumar; Pradhan, Saktipada

2018-02-01

This study was carried out to determine the concentrations of four heavy metals, cadmium (Cd), lead (Pb), copper (Cu), and cobalt (Co), and histopathological lesions in tissues of chickens reared in an industrial area of West Bengal, India. In particular, Mejhia Block was selected as a heavy metal-exposed area and Vatar Block (120 km away from industrially polluted areas) as a reference site. Samples were collected from the backyard chickens in these areas. Concentrations of heavy metals in soil, water, feedstuffs, tissues (liver, kidney, spleen, lung, and muscle), and droppings were greater (p  kidney > lung > spleen > muscle. Heavy metal concentrations were greater in older chickens (> 1 year) than in young chickens (heavy metal exposure. Histological changes revealed necrotic lesions and tubulitis in the kidney, degeneration and necrosis in liver parenchyma, and periarteriolitis, peribronchiolitis, and presence of hemosiderin pigment in the lung of chickens in the exposed site. Results indicated that backyard chickens in heavy metal-exposed site may show pathological lesions in different tissues due to accumulation of heavy metals, and thus, the consumption of chicken meat from the industrially exposed site may pose a potential health risk to local residents of polluted sites.

A study of polluted eco-system around industrial areas

International Nuclear Information System (INIS)

Husaini, S.N.; Khan, E.U.; Qureshi, I.E.; Malik, F.; Zaidi, J.H.; Arif, M.; Fatima, I.; Arif, M.

2005-01-01

Industrial pollution is one of the most serious problems in Pakistan. The uncontrolled release of untreated industrial effluents to large water bodies has deleterious effects on water quality, aquatic life and human health. The concentration of heavy metals in eco-system is reaching at alarming levels and is increasing yearly. In reality, the industries are not equipped with proper effluent treatment plants. The environmental protection law is not strictly implemented to limit the release and/or proper disposal of industrial effluents. Therefore, volume of specified industrial discharge is growing at an exponential rate without any specific safeguards. Effective measures, which can eliminate or considerably reduce hazardous factors from the human environment to minimize the associated health risks, must be identified and eradicated. In order to achieve these objectives, the study has been done to reach a balanced assessment of the risks and benefits involved. For this purpose two industrial cities of Pakistan namely, Gujranwala and Faisalabad have been selected. Four major industries existing in these cities, namely Yam, textile, paper and board and ceramics, have been studied. The specimens of the irrigated soil exposed to the industrial effluent, crops and vegetables grown on that soil have been analyzed study the hazardous effects on human health. (author)

Risk Mapping Case Study: Industrial Area Of Trinec Town (Czech Republic) potentially endangered by floods and landslides

Science.gov (United States)

Dobes, P.; Hrdina, P.; Kotatko, A.; Danihelka, P.; Bednarik, M.; Krejci, O.; Kasperakova, D.

2009-04-01

One of present questions in the context of natural and technological risk mapping, which become important in last years, is analysis and assessment of selected types of multirisks. It results from relevant R&D projetcs and also from international workshops and conferences. From various surveys and presented activities it is evident existence a lot of data and methodological approaches for single risk categories but a lack of tested methodological approaches for multirisks. Within framework of workgroup was done literature search of multirisk assessment methodologies and innovations. The idea of this relatively small, local scale case study arose during the 3rd Risk Mapping Workshop, coordinated by EC DG JRC, IPSC in November 2007. The proposal was based on the previous risk analysis and assessment project, which has been done for Frydek-Mistek County area (Czech Republic) in the year 2002. Several industrial facilities in the Trinec are partly situated in the inundation area of river Olše and are partly protected by concrete barriers built on the banks of Olše. It has to be mentioned that these banks are unstable and in the permanent slow movement. If iron-concrete barriers will be overflowed by water as the result of sudden bank landslide or flood wave, it could trigger several industrial accidents on steel and energy production facilities. Area is highly developed from demographic and socioeconomic point of view. Selected area is in high stage of geological, engineering geological and hydrogeological investigation. Most important scenarios of acidents in the area were developed by What-If analysis and Black box analysis (just growth of several different scenarios; qualitative analysis). In the period of few years later, more QRA analyses of industrial risks were proceeded separately, thanks to District Office, public and Seveso II Directive requirements. General scenarios of multi-hazard events was considered. In the case study, three methodologies was applied

[Heavy Metals Pollution in Topsoil from Dagang Industry Area and Its Ecological Risk Assessment].

Science.gov (United States)

Zhang, Qian; Chen, Zong-juan; Peng, Chang-sheng; Li, Fa-sheng; Gu, Qing-bao

2015-11-01

Based on previous studies and field investigation of Dagang industry area in Tianjin, a total of 128 topsoil samples were collected, and contents of 10 heavy metals (As, Cd, Cr, Co, Cu, Pb, Ni, V, Zn and Hg) were determined. The geoaccumulation index and geostatistics were applied to examine the degree of contamination and spatial distribution of heavy metals in topsoil. The assessment on ecological risk of heavy metals was carried out using Hakanson's method, and the main resources of the heavy metals were analyzed as well. It was found that As, Cd and Co had the highest proportions exceeding Tianjin background value, which were 100%, 97.66% and 96.88%, respectively; the heavy-metal content increased to some extent comparing with that in 2004, and the pollutions of As and Cd were the worst, and other metals were at moderate pollution level or below. The ecological risks of heavy metals were different in topsoil with different land use types, the farmland soil in the southwest as well as soils adjacent to the industrial land were at relatively high potential ecological risk level, and the integrated ecological risk index reached up to 1 437.37. Analysis of correlation and principal component showed that traffic and transportation as well as agricultural activities might be the main resources of heavy metals in the area, besides, the industrial activities in the region might also affect the accumulation of heavy metals.

Radiological protection principles concerning the release for industrial use of areas contaminated from uranium mining

International Nuclear Information System (INIS)

Anon.

1993-01-01

With regard to uses of contaminated grounds as industrial sites, generally all exposure pathways relevant during stays outdoors have to be evaluated. Assuming conditions as realistic as possible, but sufficiently conservative, the dose estimates reveal that radiation exposure from inhalation of both contaminated dust particles and Rn-decay products is lower by almost one order of magnitude than external radiation exposure. The gamma dose rate above the contaminated areas and the potential input of radioactivity into the ground water therefore are relevant exposure pathways during the use of contaminated grounds as mere industrial sites. (orig./DG) [de

Supply chain improvements through clustering: Relationships and competitive collaboration in the Norwegian furniture industry

OpenAIRE

Lindholm, Jorunn; Rødstøl, Anna With

2015-01-01

Master's thesis in Firm management There is an on-going debate regarding what Norway will do when the country can no longer rely as heavily on the oil as a source of wealth and prosperity. As there is a tradition for designing and making furniture in Norway, and the furniture industry is not dependent on favourable natural conditions, this industry could represent an alternative. As the Norwegian furniture manufacturing companies are producing in one world’s most high waged countries, ...

Current target industry analysis: Las Vegas Metropolitan Area

International Nuclear Information System (INIS)

Boyle, M.R.

1988-06-01

This is the second of three reports dealing with the Las Vegas MSA's economic development potential in support of an overall effort to prepare an environmental impact statement for the proposed underground nuclear waste storage facility at Yucca Mountain. The first report provides an assessment of the MSA current business climate for economic growth. This second report draws on that business climate assessment to evaluate the Las Vegas MSA's competitive posture in pursuing business investment in the ''primary'' sector of the economy -- businesses which sell their products or services outside the local marketplace and bring new money back into the area and businesses serving local customers who would otherwise import these products or services from suppliers outside the area. GSO has developed an analytic tool which attempts to model the decision process used by businesses in selecting locations for new or expanded business investment. This computer based model reflects variations in site selection decision making among industries and ownership and management types. The underlying premise of the GSO locational compatibility index (LCI) model is that locational decisions are based more on a process of elimination that on a process of selection. There are many factors, some essential and some desirable, which influence any site selection decision. Multivariate comparative analyses narrow the geographic field to a region, then a group of states, then a state, then a sub-state region, then a community and finally to a specific site. Sometimes these analyses are rational and quantitative. More often, they are at least partially random and intuitive. 2 tabs

Guidelines for planning interventions against external exposure in industrial area after a nuclear accident. Pt. 2. Calculation of doses using Monte Carlo method

International Nuclear Information System (INIS)

Kis, Z.; Eged, K.; Meckbach, R.; Mueller, H.

2003-01-01

Countermeasures being different from the usual urban ones and largely applicable in industrial area are collected and evaluated in a separate report. The industrial area is defined here as such an area where productive and/or commercial activity is carried out. A good example is a supermarket or a factory. Based on the history of calculation models it is unambiguous that the Monte Carlo based simulation is the perspective to the dose assessment from external exposures in such a complex environment. A method of the calculation of doses from external exposures in urban-industrial environment is presented. Moreover, this report gives a summary about the time dependence of the source strengths relative to a reference surface and a short overview about the mechanical and chemical intervention techniques which can be applied in this area. Using a hypothetical scenario (a supermarket area contaminated by 137 Cs) the details of an exemplary calculation are given directly addressing the dose and averted dose blocks of the templates of industrial countermeasures. In addition, a sensitivity analysis of the results is presented. (orig.)

MLP based models to predict PM10, O3 concentrations, in Sines industrial area

Science.gov (United States)

Durao, R.; Pereira, M. J.

2012-04-01

Sines is an important Portuguese industrial area located southwest cost of Portugal with important nearby protected natural areas. The main economical activities are related with this industrial area, the deep-water port, petrochemical and thermo-electric industry. Nevertheless, tourism is also an important economic activity especially in summer time with potential to grow. The aim of this study is to develop prediction models of pollutant concentration categories (e.g. low concentration and high concentration) in order to provide early warnings to the competent authorities who are responsible for the air quality management. The knowledge in advanced of pollutant high concentrations occurrence will allow the implementation of mitigation actions and the release of precautionary alerts to population. The regional air quality monitoring network consists in three monitoring stations where a set of pollutants' concentrations are registered on a continuous basis. From this set stands out the tropospheric ozone (O3) and particulate matter (PM10) due to the high concentrations occurring in the region and their adverse effects on human health. Moreover, the major industrial plants of the region monitor SO2, NO2 and particles emitted flows at the principal chimneys (point sources), also on a continuous basis,. Therefore Artificial neuronal networks (ANN) were the applied methodology to predict next day pollutant concentrations; due to the ANNs structure they have the ability to capture the non-linear relationships between predictor variables. Hence the first step of this study was to apply multivariate exploratory techniques to select the best predictor variables. The classification trees methodology (CART) was revealed to be the most appropriate in this case.. Results shown that pollutants atmospheric concentrations are mainly dependent on industrial emissions and a complex combination of meteorological factors and the time of the year. In the second step, the Multi

Assessment of heavy metals in the industrial effluents, tube-wells and municipal supplied water of Dehradun, India.

Science.gov (United States)

Kulshrestha, Shail; Awasthi, Alok; Dabral, S K

2013-07-01

The bio-geochemical cycles of metals involve the lands, rivers, oceans and the atmosphere. Although a large number of metals are introduced to the water bodies during their mining and extraction processes and geochemical weathering of rocks, but the role of domestic and industrial wastes is predominant and of much concern. Increased industrial activities has increased the incidence of percolation of toxic metal ions to the soil and water bodies and presently their presence in ecosystem, have reached to an alarming level that environmentalists are finding it difficult to enforce control measures. Human activities and large number of small and big industrial units are increasingly discharging deleterious metals present in the effluents and wastes, to the environment and aquatic systems and have contaminated heavily even the ground water. The toxic metals have a great tendency of bioaccumulation through which they enter the food chain system and ultimately affect adversely the life on this planet Earth in various ways. Further, due to contamination of irrigation system by the harmful Chemicals and toxic metals, the farm products, vegetables, fruits, potable water and even milk is not spared. This paper describes the assessment of the heavy metal concentration in various industrial effluents of the surrounding area. Various physico-chemical characteristics of the effluents collected from various sites are also reported. To assess the status of ground water quality, water samples from four tube wells of different localities of the area and four drinking water samples supplied by Municipal Distribution System were also analyzed.

Conductivity and superconductivity in heavily vacant diamond

Directory of Open Access Journals (Sweden)

S A Jafari

2009-08-01

Full Text Available   Motivated by the idea of impurity band superconductivity in heavily Boron doped diamond, we investigate the doping of various elements into diamond to address the question, which impurity band can offer a better DOS at the Fermi level. Surprisingly, we find that the vacancy does the best job in producing the largest DOS at the Fermi surface. To investigate the effect of disorder in Anderson localization of the resulting impurity band, we use a simple tight-binding model. Our preliminary study based on the kernel polynomial method shows that the impurity band is already localized at the concentration of 10-3. Around the vacancy concentration of 0.006 the whole spectrum of diamond becomes localized and quantum percolation takes place. Therefore to achieve conducting bands at concentrations on the scale of 5-10 percent, one needs to introduce correlations such as hopping among the vacancies .

French parapetroleum industry: results of 1992 survey

International Nuclear Information System (INIS)

Valentin, E.; Trouve, O.

1992-01-01

The petroleum prospection and production industries have developed a parapetroleum sector that is considerable in size and has been going through profound changes over the past few years. Under the impetus of acquisitions and mergers, the supply has become heavily concentrated, and now reorganized around a growing demand for integrated services. Petroleum companies tend to farm out a growing portion of their business, and this sharing out of competence and sometimes of responsibilities is breeding new types of partnership arrangements between the petroleum and parapetroleum business. This paper gives the results of an survey led in 1991 on petroleum international economy and gives statistical informations on french parapetroleum industry (exploration-production investments, exploratory wells drilled, drilling equipment in action, offshore operations, turnover evolution, shortage of manpower). 14 figs., 5 tabs

Iraqi oil industry slowly returning to normal

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that Iraq is making progress in putting its battered petroleum industry back together 1 1/2 years after the Persian Gulf war ended. OPEC News Agency (Opecna) reported the finish of reconstruction of Iraq's Mina al-Bakr oil terminal on the northern tip of the Persian Gulf, using Iraqi know-how and engineering personnel. The terminal, heavily damaged during the gulf conflict, has been restored to its prewar loading capacity of 1.6 million b/d at a cost of $16 million. Ninety per cent of the port had been damaged

Uncertainties for industrial suppliers in view to conversions and designs of research reactors

International Nuclear Information System (INIS)

Roegler, H.J.; Stroemich, A.

1991-01-01

The different national RERTR-programs have had substantial results and offer clear potential for LEU-fuel. Nevertheless there are still attempts, papers and political actions based on future developments of LEU-fuel. They may create the same uncertainty as 10 years ago again, depending on what plant the industry has to supply. Only one conclusion can be drawn: There has to be an agreement on the results of the RERTR-programs binding for all parties and the industry has a right to demand such agreement after 10 years of heavily subsidised fuel development. (orig.)

Evaluation of water resources around Barapukuria coal mine industrial area, Dinajpur, Bangladesh

Science.gov (United States)

Howladar, M. Farhad; Deb, Pulok Kanti; Muzemder, A. T. M. Shahidul Huqe; Ahmed, Mushfique

2014-09-01

Water is a very important natural resource which can be utilized in renewable or non-renewable forms but before utilizing, the evaluation of the quality of this resource is crucial for a particular use. However, the problems of water quality are more severe in areas where the mining and mineral processes' industries are present. In mining processes, several classes of wastes are produced which may turn into ultimately the sources of water quality and environmental degradation. In consequences, the evaluations of water quality for livestock, drinking, irrigation purposes and environmental implications have been carried out around the Barapukuria Coal Mining Industry under different methods and techniques such as primarily the field investigation; secondly the laboratory chemical analysis and thirdly justified the suitability of the laboratory analysis with statistical representation and correlation matrix, Schoeller plot, Piper's Trilinear diagram, Expanded Durov diagram, Wilcox diagram, US salinity diagram, Doneen's chart and others. The results of all surface and ground water samples analysis show that the characteristics and concentrations of all the major physical and chemical parameters such as pH, EC, TDS, Na+, K+, Ca2+, Mg2+, Fetotal, Cl-, HCO3 -, CO3 2- and SO4 2- are varied from one sample to other but well analogous with the WHO and EQS standard limit for all purposes in the area where the abundance of the major ions is as follows: Ca2+ > Na+ > Mg2+ > K+ > Fetotal = HCO3 - > SO4 2- > Cl- > CO3 2-. The graphical exposition of analytical data demonstrates two major hydrochemical facies for example: calcium-bicarbonate (Ca2+- HCO3 -) and magnesium-bicarbonate (Mg2+- HCO3 -) type facies which directly support the shallow recently recharged alkaline water around the industry. The calculated values for the evaluation classification of water based on TDS, Na%, EC, SAR, PI, RSC, MH, and TH replicate good to excellent use of water for livestock, drinking and

Tourism revenue as a conservation tool for threatened birds in protected areas.

Science.gov (United States)

Steven, Rochelle; Castley, J Guy; Buckley, Ralf

2013-01-01

Many bird populations worldwide are at risk of extinction, and rely heavily on protected area networks for their continued conservation. Tourism to these areas contributes to conservation by generating revenue for management. Here we quantify the contribution of tourism revenue for bird species in the IUCN Red List, using a simple accounting method. Relevant data are available for 90 (16%) of the 562 critically endangered and endangered species. Contributions of tourism to bird conservation are highest, 10-64%, in South America, Africa, and their neighbouring islands. Critically endangered bird species rely on tourism more heavily than endangered species (pmanagement budgets by promoting birdwatching tourism specifically.

Yield strength of a heavily drawn Cu-20% Nb filamentary microcomposite

International Nuclear Information System (INIS)

Hong, S.I.

1998-01-01

It has been well documented that heavily-drawn, copper-niobium microcomposites possess high strength and high conductivity. Since niobium has little solubility in copper, the conductivity of the copper is not strongly affected by the addition of niobium. Following extensive mechanical deformation of Cu-Nb, niobium dendrites transform into fine niobium ribbons as a result of the niobium texture upon drawing. This nanostructure contributes to the ultrahigh strength of Cu-Nb microcomposites. The strength of heavily deformed Cu-Nb exceeds that predicted by the rule-of-mixtures (ROM), and a fundamental understanding of the strengthening mechanisms involved has been the subject of much discussion. Spitzig and his coworkers suggests a barrier strengthening model while Funkenbusch and Courtney believe that stored dislocations have a role in substructural hardening. Hangen and Raabe recently proposed an analytical model for the calculation of the yield strength of Cu-Nb microcomposite. The model of Hangen and Raabe and that of Spitzig and his coworkers have a great deal of resemblance since both models attribute the strength to the difficulty of propagating plastic flow through the interface. The purpose of this study was to enhance the understanding of the strengthening mechanisms associated with Cu-Nb microcomposites by examining the previous studies on mechanical and microstructural stability of Cu-based microcomposites

Temporal characteristics of black carbon concentrations and its potential emission sources in a southern Taiwan industrial urban area.

Science.gov (United States)

Cheng, Yu-Hsiang; Lin, Chi-Chi; Liu, Jyh-Jian; Hsieh, Cheng-Ju

2014-03-01

This study investigates the temporal characteristics of black carbon and its potential emission sources, as well as the fractions of BC in PM2.5 levels in Kaohsiung urban area, which is an industrial city in southern Taiwan. Concentrations of BC and PM2.5 are monitored continuously from March 2006 to February 2010, using an aethalometer and a tapered element oscillating microbalance monitor. Additionally, the presence of organic compounds (or UV enhanced species) in particles at the sampling site is determined using the Delta-C (UVBC-BC) value. According to long-term measurement results, BC and PM2.5 concentrations are 3.33 and 34.0 μg m(-3), respectively, in the Kaohsiung urban area. The ratio of BC/PM2.5 is approximately 11 %. Low concentration of BC and PM2.5 in the summer of this study period is mostly likely owing to meteorological conditions that favored dispersion of local air pollutants. Nevertheless, BC concentrations peaked markedly during morning hours (7:00-11:00), likely owing to local traffic congestion. Measurement results suggest that BC is released from local traffic activities and emitted from industrial activities at this sampling site. Additionally, Delta-C values are significantly higher than zero during January-March and November-December periods in this industrial urban area, implying that UV enhanced species can be observed. At this sampling site, these UV enhanced species do not only originate from household activity and solid waste burning but also release from industrial activities. The elevated Delta-C values during nighttime (18:00-6:00) in the autumn and winter seasons are likely related to those UV enhanced species in the atmosphere, which can be condensed on particle surface under low temperature conditions. According to long-term measurement results, significantly positive Delta-C values can be observed under temperatures industrial parks and a coal-fired power plant.

A model for describing the eutrophication in a heavily regulated coastal lagoon. Application to the Albufera of Valencia (Spain).

Science.gov (United States)

del Barrio Fernández, Pilar; Gómez, Andrés García; Alba, Javier García; Díaz, César Álvarez; Revilla Cortezón, José Antonio

2012-12-15

A simplified two-dimensional eutrophication model was developed to simulate temporal and spatial variations of chlorophyll-a in heavily regulated coastal lagoons. This model considers the hydrodynamics of the whole study area, the regulated connexion of the lagoon with the sea, the variability of the input and output nutrient loads, the flux from the sediments to the water column, the phytoplankton growth and mortality kinetics, and the zooplankton grazing. The model was calibrated and validated by applying it to the Albufera of Valencia, a hypertrophic system whose connection to the sea is strongly regulated by a system of sluice-gates. The calibration and validation results presented a significant agreement between the model and the data obtained in several surveys. The accuracy was evaluated using a quantitative analysis, in which the average uncertainty of the model prediction was less than 6%. The results confirmed an expected phytoplankton bloom in April and October, achieving mean maximum values around 250 μg l(-1) of chlorophyll-a. A mass balance revealed that the eutrophication process is magnified by the input loads of nutrients, mainly from the sediments, as well as by the limited connection of the lagoon with the sea. This study has shown that the developed model is an efficient tool to manage the eutrophication problem in heavily regulated coastal lagoons. Copyright © 2012 Elsevier Ltd. All rights reserved.

Annual budget of Gd and related Rare Earth Elements in a river basin heavily disturbed by anthropogenic activities.

Science.gov (United States)

Hissler, Christophe; Stille, Peter; Guignard, Cédric; François Iffly, Jean; Pfister, Laurent

2014-05-01

The real environmental impact of micropollutants in river systems can be difficult to assess, essentially due to uncertainties in the estimation of the relative significance of both anthropogenic and natural sources. The natural geochemical background is characterized by important variations at global, regional or local scales. Moreover, elements currently considered to be undisturbed by human activities and used as tracers of continental crust derived material have become more and more involved in industrial or agricultural processes. The global production of lanthanides (REE), used in industry, medicine and agriculture, for instance, has increased exponentially from a few tons in 1950 to projected 185 kt in 2015. Consequently, these new anthropogenic contributions impact the natural cycle of the REE. Gd and related REE are now worldwide recognized as emergent micropollutants in river systems. Nevertheless, there is still a gap concerning their temporal dynamics in rivers and especially the quantification of both the anthropogenic and natural contributions in surface water. The acquisition of such quantitative information is of primordial interest because elements from both origins may present different bioavailability and toxicity levels. Working at the river basin scale allows for quantifying micropollutant fluxes. For this reason, we monitored water quality and discharge of the Alzette River (Luxembourg, Europe) over two complete hydrological cycles (2010-2013). The substantial contamination, is principally due to the steel industry in the basin, which has been active from 1875 until now, and to the related increase of urban areas. The particulate and dissolved fractions of river water were monitored using a multitracer approach (standard parameters for water quality including REE concentrations, Pb, Sr, Nd radiogenic isotopes) with two sampling setups (bi-weekly and flood event based sampling). This extensive sampling design allowed quantifying the annual

Regional risk assessment approaches to land planning for industrial polluted areas in China: the Hulunbeier region case study.

Science.gov (United States)

Li, Daiqing; Zhang, Chen; Pizzol, Lisa; Critto, Andrea; Zhang, Haibo; Lv, Shihai; Marcomini, Antonio

2014-04-01

The rapid industrial development and urbanization processes that occurred in China over the past 30years has increased dramatically the consumption of natural resources and raw materials, thus exacerbating the human pressure on environmental ecosystems. In result, large scale environmental pollution of soil, natural waters and urban air were recorded. The development of effective industrial planning to support regional sustainable economy development has become an issue of serious concern for local authorities which need to select safe sites for new industrial settlements (i.e. industrial plants) according to assessment approaches considering cumulative impacts, synergistic pollution effects and risks of accidental releases. In order to support decision makers in the development of efficient and effective regional land-use plans encompassing the identification of suitable areas for new industrial settlements and areas in need of intervention measures, this study provides a spatial regional risk assessment methodology which integrates relative risk assessment (RRA) and socio-economic assessment (SEA) and makes use of spatial analysis (GIS) methodologies and multicriteria decision analysis (MCDA) techniques. The proposed methodology was applied to the Chinese region of Hulunbeier which is located in eastern Inner Mongolia Autonomous Region, adjacent to the Republic of Mongolia. The application results demonstrated the effectiveness of the proposed methodology in the identification of the most hazardous and risky industrial settlements, the most vulnerable regional receptors and the regional districts which resulted to be the most relevant for intervention measures since they are characterized by high regional risk and excellent socio-economic development conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Large-area functionalized CVD graphene for work function matched transparent electrodes

Science.gov (United States)

Bointon, Thomas H.; Jones, Gareth F.; de Sanctis, Adolfo; Hill-Pearce, Ruth; Craciun, Monica F.; Russo, Saverio

2015-11-01

The efficiency of flexible photovoltaic and organic light emitting devices is heavily dependent on the availability of flexible and transparent conductors with at least a similar workfunction to that of Indium Tin Oxide. Here we present the first study of the work function of large area (up to 9 cm2) FeCl3 intercalated graphene grown by chemical vapour deposition on Nickel, and demonstrate values as large as 5.1 eV. Upon intercalation, a charge density per graphene layer of 5 ṡ 1013 ± 5 ṡ 1012 cm-2 is attained, making this material an attractive platform for the study of plasmonic excitations in the infrared wavelength spectrum of interest to the telecommunication industry. Finally, we demonstrate the potential of this material for flexible electronics in a transparent circuit on a polyethylene naphthalate substrate.

AFM of metallic nano-particles and nano-structures in heavily irradiated NaCl

NARCIS (Netherlands)

Gaynutdinov, R; Vainshtein, DI; Hak, SJ; Tolstikhina, A; Den Hartog, HW

2003-01-01

AFM investigations are reported for heavily, electron irradiated NaCl crystals in ultra high vacuum (UHV) in the non-contact mode-with an UHV AFM/STM Omicron system. To avoid chemical reactions between the radiolytic Na and oxygen and water, the irradiated samples were cleaved and prepared for the

Appraisal of venomous metals in selected crops and vegetables from industrial areas of the Punjab Province

International Nuclear Information System (INIS)

Husaini, S.N.; Matiullah; Arif, M.

2011-01-01

Due to the inadequate water sources, usually sewerage water and industrial effluents are being use for irrigation of the agricultural land around the industrial areas in Pakistan wherein crops and vegetables are cultivated. As untreated effluents contain heavy elements, toxic metals and organic pollutants that may find its way through food chain to general public and may cause health hazards. It is, therefore, mandatory to assess the toxic metals in such crops and vegetables. In this regard, samples of corn, millet, cabbage, spinach and potato were collected within the vicinity of industrial areas of the Faisalabad and Gujranwala regions. The food samples were analyzed using neutron activation analysis (NAA) technique. The highest concentration values of Arsenic (1.9 ± 0.1 μg/g) and Cobalt (0.85 ± 0.01 μg/g) were found in cabbage whereas Manganese (91.6 ± 0.2 μg/g), Antimony (0.15 ± 0.03 μg/g) and Selenium (1.1 ± 0.1 μg/g) were observed in spinach and Chromium (9.63 ± 1.3 μg/g) was found in millet crop. The observed concentrations of all the toxic and heavy metals in crops and vegetables are higher than those reported in the literature. (author)

A study on PCB, PCDD/PCDF industrial contamination in an urban/agricultural area. Part I - Soil

Energy Technology Data Exchange (ETDEWEB)

Turrio-Baldassarri, L.; Alivernini, S.; Battistelli, C.L. [Istituto Superiore di Sanita, Rome (IT)] (and others)

2004-09-15

The Istituto Superiore di Sanita is involved in a study on the impact of existing and past industrial activities as possible sources of contamination on the surrounding environment. The study will focus on an industrial plant inside Brescia, a city in the north-west of Italy, where, from 1938 to 1984, 150 tons of polychlorinated biphenyls (PCBs) were produced. In 1994, 1996 and 1998 three monitoring programs, preliminary to the construction of a municipal waste incinerator near the industrial plant, were carried out. High PCBs levels in soils were observed, namely 3000-6000 fold higher than the limits (0,001mg/Kg) allowed by the 1999 Italian law, in an agricultural area where several small farms are located; the farmers have been consuming for a long time food, such as milk and meat, produced in their own farms. This study has different aims: confirming and enriching previous data; helping determining the contamination source; measuring the contamination of the animals living in the area or fed with contaminated forage; evaluate the exposure of the farmers as compared to general population. Moreover, this study is interested in studying the PCB and PCDD/PCDF transfer from soils to humans across the food chain.

Tracking with heavily irradiated silicon detectors operated at cryogenic temperatures

International Nuclear Information System (INIS)

Casagrande, L.; Barnett, B.M.; Bartalina, P.

1999-01-01

In this work, the authors show that a heavily irradiated double-sided silicon microstrip detector recovers its performance when operated at cryogenic temperatures. A DELPHI microstrip detector, irradiated to a fluence of ∼4 x 10 14 p/cm 2 , no longer operational at room temperature, cannot be distinguished from a non-irradiated one when operated at T < 120 K. Besides confirming the previously observed Lazarus effect in single diodes, these results establish, for the first time, the possibility of using standard silicon detectors for tracking applications in extremely demanding radiation environments

3D electrical image in area contaminated by hydrocarbons at the Cubatao, Brazil, industrial pole; Imageamento eletrico 3D em area contaminada por hidrocarbonetono no polo industrial de Cubatao - SP, Brasil

Energy Technology Data Exchange (ETDEWEB)

Baessa, Marcus Paulus Martins [Centro de Pesquisas e Desenvolvimento Leopoldo Americo Miguez de Mello, CENPES, Rio de Janeiro, RJ (Brazil)], E-mail: marcus.baessa@petrobras.br; Oliva, Andresa; Kiang, Chang Hung [Universidade Estadual Paulista, UNESP, Rio Claro, SP (Brazil)], E-mails: aoliva@rc.unesp.br, chang@rc.unesp.br

2010-12-15

This work presents the results of geophysical surveys performed over an oil contaminated site in the Polo Industrial de Cubatao - Sao Paulo. The aim is to characterize geoelectrical signatures associated to hydrocarbon presence in order to delimit and calculate the volume of the contaminated area. For this study were used Vertical Electrical Sounding (VES) and 3D Electrical Imaging for characterization of geology and geoelectrical response of the contaminant. The results showed that the hydrocarbon presence is associated to conductive anomalies due to products from biodegradation. The conductive anomalies are disseminated over the area, totalizing 1365.3 m3 volume. This volume, however, corresponds only to the residual phase contaminants, since it was not possible to map free-phase hydrocarbons. (author)

Theoretical investigation of the heavily-doped semiconductor aspect of ultra-dilute GaAsN

Science.gov (United States)

Sukpitak, Jessada; Sa-yakanit, Virulh

2015-12-01

The model of GaAs1- y N y ( y = 0.001) as a heavily-doped semiconductor in the ultra-dilute region is attentively examined. The model enables GaAsN to be viewed as a disordered assembly of three-dimensional quantum dots (potential wells) caused by random potential fluctuations from nitrogen pairs in the system. Consequently, Feynman's path-integration technique is applied in order to quantify the density of states (DOS) in the vicinity of the conduction band edge. The obtained DOS tail, even though overestimated, still clearly shows a much shorter tail than that the experimental result does. This shows that the heavily-doped semiconductor viewpoint is not proper for GaAsN, not even in the ultra-dilute region. Furthermore, this also suggests that the impurity wave function overlap is not a basic mechanism of band gap reduction.

Antioxidant response of three Tillandsia species transplanted to urban, agricultural, and industrial areas.

Science.gov (United States)

Bermudez, Gonzalo M A; Pignata, María Luisa

2011-10-01

To evaluate the physiological response of Tillandsia capillaris Ruiz & Pav. f. capillaris, T. recurvata L., and T. tricholepis Baker to different air pollution sources, epiphyte samples were collected from a noncontaminated area in the province of Córdoba (Argentina) and transplanted to a control site as well as three areas categorized according to the presence of agricultural, urban, and industrial (metallurgical and metal-mechanical) emission sources. A foliar damage index (FDI) was calculated with the physiological parameters chlorophyll a, chlorophyll b, malondialdehyde (MDA), hydroperoxyconjugated dienes, sulfur (S) content, and dry weight-to-fresh weight ratio. In addition, electrical conductivity (E-cond), relative water content (RWC), dehydration kinetics (Kin-H(2)O), total phenols (T-phen), soluble proteins (S-prot), and activities of superoxide dismutase (SOD), catalase (CAT), and ascorbate peroxidase were determined. The parameters E-cond, FDI, SOD, RWC, and Kin-H(2)O can serve as suitable indicators of agricultural air pollution for T. tricholepis and T. capillaris, and CAT, Kin-H(2)O, and SOD can do the same for T. recurvata. In addition, MDA, T-phen, and S-prot proved to be appropriate indicators of urban pollution for T. recurvata. Moreover, FDI, E-cond, and SOD for T. recurvata and MDA for T. tricholepis, respectively, could be used to detect deleterious effects of industrial air pollution. © Springer Science+Business Media, LLC 2011

Metals interaction tested in children’s hair originating from industrial and rural areas

Directory of Open Access Journals (Sweden)

Jerzy Kwapulinski

2014-09-01

Full Text Available Introduction. Different biological samples (blood, gallstone, teeth, hair serve as a biomarker of exposure to metals for many years. This method appeared to be useful not only in clinical medicine, but also in the studies on the environment. Aim. The study is to compare the amount of selected metals in children’s hair residing in industrial and rural areas. Material and methods. Research of occurrence of 12 metals in children’s hair at the age of 7, 10 and 14 living in an industrial (Nowy Bytom town and a rural (Strumień town areas has been presented. Determination of Pb, Cd, Ni, Co Na, K, Mg, Zn, Cu, Mn, Fe and Ca was carried out by atomic absorption spectrophotometry (AAS using a spectrometer PerkinElmer 400. Results. In the case of seven-year old children, regardless of gender a common mechanism of co-occurrence was noticed for manganese and calcium, manganese and magnesium, calcium and magnesium, sodium and potassium. Apart from the correlation of metals for the seven-year-old-children mentioned, in case of ten-year old children, an additional correlation between calcium and zinc appears. Conclusion: The amount of some metals in the hair with the diversified possibility of interaction between the metals themselves and their relation to gender and age of children revealed different environmental exposure.

Tax responses in platform industries

DEFF Research Database (Denmark)

Kind, Hans Jarle; Köthenbürger, Marko; Schjelderup, Guttorm

2010-01-01

that a higher ad valorem tax may undermine a firm's incentive to differentiate its product from that of its competitors. Finally, we demonstrate that the effects of increasing specific taxes may be the opposite of those of increasing value added taxes....... price and thus buy less of the good. The present paper shows that this result need not hold in a two-sided market. On the contrary, a higher ad valorem tax may lower end-user prices and spur sales. Thus, two-sided platform firms may not at all engage in tax shifting via price increases. We further show......Two-sided platform firms serve distinct customer groups that are connected through interdependent demand, and include major businesses such as the media industry, banking, and the software industry. A well known result of tax incidence is that consumers of a more heavily taxed good pay a higher...

Sources of heavy metal pollution in agricultural soils of a rapidly industrializing area in the Yangtze Delta of China.

Science.gov (United States)

Xu, Xianghua; Zhao, Yongcun; Zhao, Xiaoyan; Wang, Yudong; Deng, Wenjing

2014-10-01

The rapid industrialization and urbanization in developing countries have increased pollution by heavy metals, which is a concern for human health and the environment. In this study, 230 surface soil samples (0-20cm) were collected from agricultural areas of Jiaxing, a rapidly industrializing area in the Yangtze Delta of China. Sequential Gaussian simulation (SGS) and multivariate factorial kriging analysis (FKA) were used to identify and explore the sources of heavy metal pollution for eight metals (Cu, Zn, Pb, Cr, Ni, Cd, Hg and As). Localized hot-spots of pollution were identified for Cu, Zn, Pb, Cr, Ni and Cd with area percentages of 0.48 percent, 0.58 percent, 2.84 percent, 2.41 percent, 0.74 percent, and 0.68 percent, respectively. The areas with Hg pollution covered approximately 38 percent whereas no potential pollution risk was found for As. The soil parent material and point sources of pollution had significant influences on Cr, Ni, Cu, Zn and Cd levels, except for the influence of agricultural management practices also accounted for micro-scale variations (nugget effect) for Cu and Zn pollution. Short-range (4km) diffusion processes had a significant influence on Cu levels, although they did not appear to be the dominant sources of Zn and Cd variation. The short-range diffusion pollution arising from current and historic industrial emissions and urbanization, and long-range (33km) variations in soil parent materials and/or diffusion jointly determined the current concentrations of soil Pb. The sources of Hg pollution risk may be attributed to the atmosphere deposition of industrial emission and historical use of Hg-containing pesticides. Copyright © 2014 Elsevier Inc. All rights reserved.

2005-2014 trends of PM10 source contributions in an industrialized area of southern Spain.

Science.gov (United States)

Li, Jiwei; Chen, Bing; de la Campa, Ana M Sánchez; Alastuey, Andrés; Querol, Xavier; de la Rosa, Jesus D

2018-05-01

Particulate matter with a diameter of 10 μm or less (PM10) using receptor modelling was determined at an urban (La Linea, LL) and an industrial area (Puente Mayorga, PMY) in Southern Spain with samples collected during 2005-2014. The concentrations of PM10 had been decreasing at both sites in three distinctive periods: 1) the initial PM10 levels approached or exceeded the Spain and EU PM10 annual guidelines of 40 μg/m 3 during 2005-2007 at LL and 2005-2009 at PMY; 2) then PM10 dropped by 25%-∼30 μg/m 3 during 2008-2011 at LL and during 2010-2011 at PMY; 3) since 2012, the PM10 concentrations gradually decreased to major elements. These PM components generally showed a decrease trend, in accord with the trend of PM10 reduction. A PMF model identified seven sources to PM10 contributions. Secondary sulfate, soil/urban/construction dust, and secondary nitrate showed significantly decreasing trends with reduction of 40-60% comparing to the initial levels. The road traffic contribution decreased by 14% from the first to third period. However, sea salt, oil combustion, and industrial metallurgical process had relative stable contributions. These source contribution changes are reasonably governed by the PM emission abatement actions implemented during the past decade, as well as the financial crisis, that accounted for a significant decrease of PM pollution in Southern Spain. We identified that the mitigation efforts on industry, fossil fuel combustion, and urban transportation during the past decade were successful for air quality improvement in a highly industrialized area in Southern Spain. Copyright © 2018 Elsevier Ltd. All rights reserved.

Environmental Management System of Petroleum Industries: A case study of Oil and Gas Exploration in the Zamrud Field Conservation Areas

Directory of Open Access Journals (Sweden)

Onny Setiani

2015-12-01

Full Text Available ABSTRACT Background:The Zamrud Field is one of the oil fields managed by Caltex Pacific Indonesia (CPI a production sharing contractor of Pertamina. It is located in the Coastal Plain and  Pekanbaru (CPP Block. The government of Indonesia has designated Zamrud as a conservation area. The petroleum industry in Zamrud fields has received 14001 ISO Certificate on Environmental Management System. The production sharing contract between CPI and the Government of Indonesia expired in August 2002 Methods: .This case study describes how CPI managed the development  of oil and gas production and compared to  the environmental management system for  petroleum industries  that should be taken  in the Zamrud conservation areas. Results: A number of specific measures were employed by CPI  to protect this sensitive area including a green seismic project, zero-discharge drilling, water management, preservation of nature and regular monitoring and impact assessment. There are two  important points that should be in consideration  for the environmental management system by CPI in the Zamrud areas, including top soil utilization to maintain biological and nutrients quality and re-vegetation in all areas of significant disturbances. Conclusion: oil and gas  exploration and production in conservation areas has to be managed through high commitment to good environmental  and social practices. Key words     : Environmental Management System (EMS, Petroleum Industries, Zamrud Field

Assessment of heavy metal and bacterial pollution in coastal aquifers from SIPCOT industrial zones, Gulf of Mannar, South Coast of Tamil Nadu, India

Science.gov (United States)

Selvam, S.; Antony Ravindran, A.; Venkatramanan, S.; Singaraja, C.

2017-05-01

Heavy metals and microbiological contamination were investigated in groundwater in the industrial and coastal city of Thoothukudi. The main sources of drinking water in this area are water bores which are dug up to the depth of 10-50 m in almost every house. A number of chemical and pharmaceutical industries have been established since past three decades. Effluents from these industries are reportedly being directly discharged onto surrounding land, irrigation fields and surface water bodies forming point and non-point sources of contamination for groundwater in the study area. The study consists of the determination of physico-chemical properties, trace metals, heavy metals and microbiological quality of drinking water. Heavy metals were analysed using Inductively Coupled Plasma Mass Spectrometry and compared with the (WHO in Guidelines for drinking water quality, 2004) standards. The organic contamination was detected in terms of most probable number (MPN) test in order to find out faecal coliforms that were identified through biochemical tests. A comparison of the results of groundwater samples with WHO guidelines reveals that most of the groundwater samples are heavily contaminated with heavy metals like arsenic, selenium, lead, boron, aluminium, iron and vanadium. The selenium level was higher than 0.01 mg/l in 82 % of the study area and the arsenic concentration exceeded 0.01 mg/l in 42 % of the area. The results reveal that heavy metal contamination in the area is mainly due to the discharge of effluents from copper industries, alkali chemical industry, fertiliser industry, thermal power plant and sea food industries. The results showed that there are pollutions for the groundwater, and the total Coliform means values ranged from 0.6-145 MPN ml-1, faecal Coliform ranged from 2.2-143 MPN ml-1, Escherichia coli ranged from 0.9 to 40 MPN ml-1 and faecal streptococci ranged from 10-9.20 × 102 CFU ml-1. The coastal regions are highly contaminated with total

Groundwater flow in the Venice lagoon and remediation of the Porto Marghera industrial area (Italy)

Science.gov (United States)

Beretta, Giovanni Pietro; Terrenghi, Jacopo

2017-05-01

This study aims to determine the groundwater flow in a large area of the Venice (northeast Italy) lagoon that is under great anthropogenic pressure, which is influencing the regional flow in the surficial aquifer (about 30 m depth). The area presents several elements that condition the groundwater flow: extraction by means of drainage pumps and wells; tidal fluctuation; impermeable barriers that define part of the coastline, rivers and artificial channels; precipitation; recharge, etc. All the elements were studied separately, and then they were brought together in a numerical groundwater flow model to estimate the impact of each one. Identification of the impact of each element will help to optimise the characteristics of the Porto Marghera remediation systems. Longstanding industrial activity has had a strong impact on the soil and groundwater quality, and expensive and complex emergency remediation measures in problematic locations have been undertaken to ensure the continuity of industrial and maritime activities. The land reclamation and remediation works withdraw 56-74% of the water budget, while recharge from the river accounts for about 21-48% of the input. Only 21-42% of groundwater in the modelled area is derived from natural recharge sources, untouched by human activity. The drop of the piezometric level due to the realization of the upgradient impermeable barrier can be counteracted with the reduction of the pumping rate of the remediation systems.

IMPROVING PERFORMANCES BY USING COST CONTROLLING IN THE MINING INDUSTRY ENTITIES

Directory of Open Access Journals (Sweden)

SORINEL CĂPUŞNEANU

2016-06-01

Full Text Available The aim of this article is to highlight the improving performances of entities from mining industry entities by using cost controlling as an important tool of management accounting, applying the target costing method. The survey is based on questions that led investigation made in the Romanian entities from mining industry and based on data a thorough analysis was done for fulfillment of authors’ purpose. The results obtained by applying the target costing method has allowed a very strict cost control, which ultimately led to increased performances of economic entities from mining industry in Romania. The secondary purpose of this article is to try adjusting the target costing method to the specific of entities in the mining industry. According to studies of specialists this method based on target costing calculation is rather unusual in this sector of mining industry and it relies heavily on the activity-based costing method. The article ends with the authors' conclusions on improving the performances of entities from mining industry based on cost controlling and use of mix information obtained through the applied methods

A review of the epidemiological methods used to investigate the health impacts of air pollution around major industrial areas.

Science.gov (United States)

Pascal, Mathilde; Pascal, Laurence; Bidondo, Marie-Laure; Cochet, Amandine; Sarter, Hélène; Stempfelet, Morgane; Wagner, Vérène

2013-01-01

We performed a literature review to investigate how epidemiological studies have been used to assess the health consequences of living in the vicinity of industries. 77 papers on the chronic effects of air pollution around major industrial areas were reviewed. Major health themes were cancers (27 studies), morbidity (25 studies), mortality (7 studies), and birth outcome (7 studies). Only 3 studies investigated mental health. While studies were available from many different countries, a majority of papers came from the United Kingdom, Italy, and Spain. Several studies were motivated by concerns from the population or by previous observations of an overincidence of cases. Geographical ecological designs were largely used for studying cancer and mortality, including statistical designs to quantify a relationship between health indicators and exposure. Morbidity was frequently investigated through cross-sectional surveys on the respiratory health of children. Few multicenter studies were performed. In a majority of papers, exposed areas were defined based on the distance to the industry and were located from 20 km from the plants. Improving the exposure assessment would be an asset to future studies. Criteria to include industries in multicenter studies should be defined.

Historical data reveal 30-year persistence of benthic fauna associations in heavily modified waterbody

Directory of Open Access Journals (Sweden)

Ruth Callaway

2016-08-01

Full Text Available Baseline surveys form the cornerstone of coastal impact studies where altered conditions, for example through new infrastructure development, are assessed against a temporal reference state. They are snapshots taken before construction. Due to scarcity of relevant data prior to baseline surveys long-term trends can often not be taken into account. Particularly in heavily modified waterbodies this would however be desirable to control for changes in anthropogenic use over time as well as natural ecological variation. Here, the benthic environment of an industrialized embayment was investigated (Swansea Bay, Wales, UK where it is proposed to build a tidal lagoon that would generate marine renewable energy from the tidal range. Since robust long-term baseline data was not available, the value of unpublished historical benthos information from 1984 by a regional water company was assessed with the aim to improve certainty about the persistence of current benthic community patterns. A survey of 101 positions in 2014 identified spatially discrete benthic communities with areas of high and low diversity. Habitat characteristics including sediment properties and the proximity to a sewage outfall explained 17-35% of the variation in the community structure. Comparing the historical information from 1984 with 2014 revealed striking similarity in the benthic communities between those years, not just in their spatial distribution but also to a large extent in the species composition. The 30-year-old information confirmed spatial boundaries of discrete species associations and pinpointed a similar diversity hotspot. A group of five common species was found to be particularly persistent over time (Nucula nitidosa, Spisula elliptica, Spiophanes bombyx, Nephtys hombergii, Diastylis rathkei. According to the Infauna Quality Index (IQI linked to the EU Water Framework Directive (WFD the average ecological status for 2014 was ‘moderate’, but eleven samples

Chromium and nickel in the soils of industrial areas at Asopos river basin

Directory of Open Access Journals (Sweden)

Athanassios Karayannis

2016-07-01

Full Text Available The purpose of this paper is to present and compare previous efforts aiming to investigate whether previous wastewater disposal practices in selected (four metal finishing facilities, located at Asopos river basin (near Athens at East-Central Greece, and resulted in relevant soil contamination. The work is focused mainly on Cr and Ni, which are the primary elements of concern in the Asopos river Basin area. To assess the natural geochemical levels of Cr and Ni, 30 soil samples were collected from locations that were assumed free of contamination. In these 30 soil samples, Cr concentration varied from 60 to 418 mg/kg, and Ni concentrations varied between 91 and 1200 mg/kg. A second group of soil samples consisted of more than 100 samples from drill cores and surface soil samples, assumed affected by the disposal of effluents of the metal finishing facilities and/or the relevant drainage of runoff water. A third group of samples consisted of 10 more surface soil samples collected in summer 2015 (campaigns by Sybilla ltd in the framework of EU IED Directive Baseline Site Investigation Study for two metal finishing units. The above mentioned groups of data were evaluated and compared with a fourth group of data (collected from Inofyta industrial area in the framework of EU funded project LIFE-CHARM “Chromium in Asopos groundwater system: Remediation technologies and Measures”. The conclusion of this study is that there is no indication of downstream pollution migration from the land-based treated effluents disposal of the above mentioned metal finishing facilities. Cr and Ni concentrations in the lower soil layers were of the same order of magnitude to those of the reference soils. On the contrary Inofyta Industrial Area soil seems to be rather contaminated and requires special attention.

Strategic marketing in the UK tobacco industry.

Science.gov (United States)

Anderson, Susan; Hastings, Gerard; MacFadyen, Lynn

2002-08-01

Tobacco-industry marketing has played a central part in the global spread of tobacco use and addiction. Although the absolute size of the tobacco market has dwindled, the industry is still immensely successful, largely due to sophisticated and manipulative marketing strategies. The UK tobacco industry identifies target groups and builds enduring relationships based on careful brand management. Potential customers are exposed to brands which are likely to appeal to them most. Tobacco companies tailor their products to target markets by altering the content of tar and nicotine, and by adding flavourings to produce a distinctive taste. Marketing strategies ensure that the products are promoted heavily at the point of sale, and directed advertising and sponsorship agreements are used to increase the visibility of the brand and strengthen its image. Tobacco companies also target non-consumer organisations such as retailers and policy makers with the aim of creating the best possible business environment for tobacco sales. We review published evidence, internal-advertising-agency documents, and observational data about tobacco promotion, and discuss the use of targeted marketing strategies in the UK.

An X-ray wave theory for heavily distorted crystals. 1

International Nuclear Information System (INIS)

Ohkawa, T.; Hashimoto, H.

1985-01-01

An X-ray diffraction theory is developed of monochromatic waves having spherical wave front, which is applicable to an interpretation of divergent X-ray diffraction images of crystals containing arbitral types of strain field. The theory is divided into two parts. In part I, Takagi's theory is expanded by introducing amplitude and phase correction functions and a new improved representation for the X-ray diffraction theory is given. In part II dispersion surfaces in heavily distorted crystals are discussed, and in the discussion the resonance shift functions are introduced. These formulations can lead to a complete understanding of the extinction phenomena. (author)

The impact of Romania’s industrialization during the ’70s and ’80s on the environment

Directory of Open Access Journals (Sweden)

Ilarion Ţiu

2014-11-01

Full Text Available In December 1972, the Romanian Government signed the agreement of accession to the International Monetary Fund and the World Bank. In the following years, Romania received investment credits and, consequently, overcame the growth rate of several capitalist states. Nevertheless, the Communist regime in Bucharest chose to expand the economic sectors highly energy intensive and heavily polluting. As the ’70s oil crisis led to a worldwide energy crisis, the Romanian industry faced difficult times in terms of effectiveness, competitiveness and external costs of environmental pollution. It had been built coal-electrical and great siderurgical & chemical plants, and both caused extremely air pollution. At the end of the ’80s, Romania recorded high pollution indicators of soil, subsoil, water and within the atmosphere down to the evacuation of residual waste and lack of investments in filtering of industrial stack. In the end, the phenomenon damaged the inhabitants’ health status of the polluted areas, causing high rates of different forms of cancer and respiratory illnesses.

Soil Contamination as a Legacy of the U.S. Auto Industry, Southwest Detroit, Michigan USA

Science.gov (United States)

Murray, K.; Peterman, C.

2012-04-01

The Delray community of southwest Detroit is one of the most depressed areas in southeast Michigan. Historically, Delray was a working class, racially diverse community that depended heavily on industrial jobs provided by nearby factories. However, decades of industrial waste discharges have left Delray with extensive air and soil pollution. Although high unemployment and poverty are major challenges confronting residents in Delray today, the threat to public health from Pb, Hg, As and Cr [VI] in the soil may become an even bigger issue and a significant source of concern. Newspaper headlines cite crime, substance abuse, high school and labor force dropout, as being prevalent in Delray, but recent research suggest that soil contamination, which has resulted in elevated blood Pb levels may be an underlying factor. Recent interest in this area as a potential site for a new bridge to Canada, has offered new hope to the residents by potentially opening the door for redevelopment. The initial step in this process is an environmental assessment of the Delray community. This investigation is being conducted by the University of Michigan-Dearborn in consortium with local community groups and the Detroit Public School. Although preliminary, an analysis of soil samples from over 400 residences has indicated that significant levels of As, and Pb are present in the upper 0.1 meter of soil throughout the Delray area. The high levels of metals present in the soil suggest that further investigation and possible remedial action will be necessary prior to redevelopment.

Budburst phenology of white birch in industrially polluted areas

International Nuclear Information System (INIS)

Kozlov, Mikhail V.; Eraenen, Janne K.; Zverev, Vitali E.

2007-01-01

Effects of environmental contamination on plant seasonal development have only rarely been properly documented. Monitoring of leaf growth in mountain birch, Betula pubescens subsp. czerepanovii, around a nickel-copper smelter at Monchegorsk hinted advanced budburst phenology in most polluted sites. However, under laboratory conditions budburst of birch twigs cut in late winter from trees naturally growing around three point polluters (nickel-copper smelter at Monchegorsk, aluminium factory at Kandalaksha, and iron pellet plant at Kostomuksha) showed no relationship with distance from the emission source. In a greenhouse experiment, budburst phenology of mountain birch seedlings grown in unpolluted soil did not depend on seedling origin (from heavily polluted vs. clean sites), whereas seedlings in metal-contaminated soil demonstrated delayed budburst. These results allow to attribute advanced budburst phenology of white birch in severely polluted sites to modified microclimate, rather than to pollution impact on plant physiology or genetics. - Advanced budburst phenology in white birch in severely polluted sites is explained by modified microclimate, not by pollution impact on plant physiology

Spatial distribution and vertical profile of polybrominated diphenyl ethers, tetrabromobisphenol A, and decabromodiphenylethane in river sediment from an industrialized region of South China

International Nuclear Information System (INIS)

Zhang Xiulan; Luo Xiaojun; Chen Shejun; Wu Jiangping; Mai Bixian

2009-01-01

Polybrominated diphenyl ethers (PBDEs), tetrabromobisphenol A (TBBPA), and decabromodiphenylethane (DBDPE) were detected in fifteen surface sediments and two sediment cores collected from a river in one heavily industrialized region of South China. TBBPA and DBDPE were detected with concentrations ranging from 3.8 to 230 ng/g dw and from 23 to 430 ng/g dw, respectively. Σtri-hepta-BDEs and Σnona-deca-BDEs ranged from 0.7 to 7.6 ng/g dw and from 30 to 5700 ng/g dw, respectively. Σtri-hepta-BDEs showed an increasing trend whereas for Σnona-deca-BDE two sediment cores revealed a decreasing trend in more recent sediment layers which may attributed to the introduction of DBDPE. The rapid increasing trend for TBBPA and DBDPE in recent sediment layers well reflected the rising demand of these two compounds in study area. - Ubiquitous and historical contamination by PBDE, TBBPA, and DBDPE in river sediments from an industrialized region of South China

Spatial distribution and vertical profile of polybrominated diphenyl ethers, tetrabromobisphenol A, and decabromodiphenylethane in river sediment from an industrialized region of South China

Energy Technology Data Exchange (ETDEWEB)

Zhang Xiulan [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School of the Chinese Academy of Science, Beijing 100039 (China); Luo Xiaojun, E-mail: luoxiaoj@gig.ac.c [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Chen Shejun [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Wu Jiangping [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School of the Chinese Academy of Science, Beijing 100039 (China); Mai Bixian [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2009-06-15

Polybrominated diphenyl ethers (PBDEs), tetrabromobisphenol A (TBBPA), and decabromodiphenylethane (DBDPE) were detected in fifteen surface sediments and two sediment cores collected from a river in one heavily industrialized region of South China. TBBPA and DBDPE were detected with concentrations ranging from 3.8 to 230 ng/g dw and from 23 to 430 ng/g dw, respectively. SIGMAtri-hepta-BDEs and SIGMAnona-deca-BDEs ranged from 0.7 to 7.6 ng/g dw and from 30 to 5700 ng/g dw, respectively. SIGMAtri-hepta-BDEs showed an increasing trend whereas for SIGMAnona-deca-BDE two sediment cores revealed a decreasing trend in more recent sediment layers which may attributed to the introduction of DBDPE. The rapid increasing trend for TBBPA and DBDPE in recent sediment layers well reflected the rising demand of these two compounds in study area. - Ubiquitous and historical contamination by PBDE, TBBPA, and DBDPE in river sediments from an industrialized region of South China

Absorption of Mercury from Polluted Soil by Rice Plant(Case Study: Farms of Amol Industrial Suburban Area

Directory of Open Access Journals (Sweden)

Fatemeh Ahmadipour

2013-03-01

Full Text Available Mercury has recognized as one of the most toxic heavy metals, which many industries generate and dispose to the environment. Few studies are done about mercury accumulation in soil and bioconcentration and transfer factor of mercury in rice plant cultivated in industrial areas. In this study samples were taken randomly from 10 farms in vicinity of Amol industrial suburban area with three replications. Samples were measured by the LECO AMA 254 Advanced Mercury Analyzer according to ASTM D-6733method. Also the parameters related to the quality of the soil were measured. The mean of mercury concentration in soil, root, stem and grain were found 0.031 ±0.012 mg/kg, 0.074 ±0.0163 mg/kg, 0.058 ±0.008 mg/kg and 0.051 ±0.0083 mg/kg respectively. The calculated transfer factor of mercury to various organs and bioconcentration factor were < 1 and 2.46 respectively. Pearson correlation test showed a positive correlation between mercury concentration in soil with mercury concentration in grain and also a negative correlation between pH with mercury concentration in root and soil. It is concluded that rice plant have high potential for phytoremediation of mercury from soil.

Identification of sources of elevated concentrations of polycyclic aromatic hydrocarbons in an industrial area in Tianjin, China

NARCIS (Netherlands)

Jiao, W.T.; Lu, Y.L.; Li, J.; Han, Jingyi; Wang, T.Y.; Luo, W.; Shi, Y.J.; Wang, G.

2009-01-01

The concentrations of 16 polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatography equipped with a mass spectrometry detector in 105 topsoil samples from an industrial area around Bohai Bay, Tianjin in the North of China. Results demonstrated that concentrations of PAHs in 104

Aerial radiological survey of the Industrial Reactor Laboratory and surrounding area Plainsboro, New Jersey

International Nuclear Information System (INIS)

1980-12-01

An airborne radiological survey of a 6 km 2 area centered over the Industrial Reactor Laboratory was made 25-27 July 1979. Detected radioisotopes and their associated gamma ray exposure rates were consistent with that expected from normal background emitters, except at two locations described in this report. Count rates observed at 46 m altitude were converted to exposure rates at 1 m above the ground and are presented in the form of an isopleth map

Evaluation of Toluene Exposure in Workers at Industrial Area of Sidoarjo, Indonesia by Measurement of Urinary Hippuric Acid

Directory of Open Access Journals (Sweden)

Moch Sahri

2013-12-01

How to cite this article: Sahri M, Widajati N. Evaluation of Toluene Exposure in Workers at Industrial Area of Sidoarjo, Indonesia by Measurement of Urinary Hippuric Acid. Asia Pac J Med Toxicol 2013;2:145-9.

Volatile organic compounds (VOCs) emission characteristics and control strategies for a petrochemical industrial area in middle Taiwan.

Science.gov (United States)

Yen, Chia-Hsien; Horng, Jao-Jia

2009-11-01

This study investigated VOC emissions from the largest petrochemical industrial district in Taiwan and recommended some control measures to reduce VOC emissions. In addition to the petrochemical industry, the district encompasses a chemical and fiber industry, a plastics industry and a harbor, which together produce more than 95% of the VOC emissions in the area. The sequence of VOC emission was as follows: components (e.g., valves, flanges, and pumps) (47%) > tanks (29%) > stacks (15%) > wastewater treatment facility (6%) > loading (2%) > flares (1%). Other plants producing high-density polyethylene (HDPE), styrene, ethylene glycol (EG), gas oil, and iso-nonyl-alchol (INA) were measured to determine the VOC leaching in the district. The VOC emissions of these 35 plants (90% of all plants) were less than 100 tons/year. About 74% of the tanks were fixed-roof tanks that leached more VOCs than the other types of tanks. To reduce leaching, the components should be checked periodically, and companies should be required to follow the Taiwan EPA regulations. A VOC emission management system was developed in state implementation plans (SIPs) to inspect and reduce emissions in the industrial district.

Aerosol pollution in urban and industrialized area under marine influence: physical-chemistry of particles

International Nuclear Information System (INIS)

Rimetz, J.

2007-12-01

Harbors for trade are known as highly urbanized and industrialized areas with important maritime, railway and road traffic. Industries are mainly represented by steel, cement works, and oil refineries. The maritime sector is becoming an even larger source of air pollution. Atmospheric NO x , SO 2 , O 3 levels and chemical analysis of airborne particulate matter were monitored in Dunkerque conurbation in 2005 and 2006. This study was included in the IRENI program. In low-pressure conditions, local pollutants are spread out far away the agglomeration, whereas, in high-pressure regimes, the atmospheric stability and sea-breezes allow an accumulation of pollutants over the urban zone. Size-resolved chemical analyses of particulate matter collected as function of the aerodynamic diameter (D a ) were performed. Ions (Na + , NH 4 + , Cl - , NO 3 - , SO 4 2- ), metals (Fe, Zn, Pb, Cd,...) and organic fraction (EC, OC) are associated with sub- or/and super-micron particles. The size, morphology and chemical species of individual particles collected selectively in the 12O 3 , Fe 3 O 4 , PbO,... containing particles emitted in the Dunkerque harbour area and aged sea-salt aerosol particles (NaCl, NaNO 3 ,...) from long range transport of air masses. Thin organic coatings from natural and anthropogenic origin are observed on the particles by ToF-SIMS imaging. (author)

Pollution and health risk assessment of industrial and residential area based on metal and metalloids contents in soil and sediment samples from and around the petrochemical industry, Serbia

Science.gov (United States)

Relic, Dubravka; Sakan, Sanja; Andjelkovic, Ivan; Djordjevic, Dragana

2017-04-01

Within this study the investigation of pollution state of metal and metalloids contamination in soils and sediments samples of the petrochemical and nearby residential area is present. The pseudo-total concentrations of Ba, Cd, Co, Cu, Cr, Mn, Ni, Pb, V, Zn, As, Hg, and Se were monitored with ICP/OES. The pollution indices applied in this work, such as the enrichment factor, the pollution load index, the total enrichment factor, and the ecological risk index showed that some of the soil and sediment samples were highly polluted by Hg, Ba, Pb, Cd, Cr Cu and Zn. The highest pollution indices were calculated for Hg in samples from the petrochemical area: chloralkali plant, electrolysis factory, mercury disposal area, and in samples from the waste channel. The pollution indices of the samples from the residential area indicated that this area is not polluted by investigated elements. Besides the pollution indices, the metal and metalloids concentrations were used in the equations for calculating the health risk criteria. We calculate no carcinogenic and carcinogenic risks for the composite worker and residential people by usage adequate equations. In analyzed samples, the no carcinogenic risks were lower than 1. The highest values of carcinogenic risk were obtained in sediment samples from the waste channel within the petrochemical industry and the metal that mostly contributes to the highest carcinogenic risk is Cr. Correlation analysis of pollution indices and carcinogenic risks calculated from the residential area samples showed good correlations while this is not the case for an industrial area.

Social cost benefit analysis of sustainable industrial areas

International Nuclear Information System (INIS)

Blom, M.J.; Schroten, A.

2010-05-01

In restructuring a industrial park many different interests are involved, such as space, business climate, environmental quality or landscape. The social cost-benefit analysis (SCBA) is a tool for mapping all current and future pros and cons (expressed in Euros) of a restructuring project for society as a whole as objective as possible. The SCBA manual for sustainable industrial parks describes how an SCBA can be performed and how the results could accommodate decisions made. SCBA pilots have been carried out for restructuring projects in four Dutch municipalities: Katwijk, Rijnwoude, Hardinxveld-Giessendam and Westland. [nl

Dual Inhibition of EGFR and VEGF in Heavily Pretreated Patients with Metastatic Colorectal Cancer

DEFF Research Database (Denmark)

Larsen, Finn Ole; Markussen, Alice; Nielsen, Dorte

2017-01-01

: The combination of irinotecan, bevacizumab, and cetuximab/panitumumab is safe and shows a toxicity profile corresponding to what is expected from the agents alone. The results indicate that the combination in the 4th line may result in a high rate of disease control in heavily pretreated patients with metastatic...

A regional synergy approach to energy recovery: The case of the Kwinana industrial area, Western Australia

International Nuclear Information System (INIS)

Beers, D. van; Biswas, W.K.

2008-01-01

Energy is a key issue in the Kwinana industrial area, Western Australia's major heavy industrial region, where the major energy consuming industries consume upto 80 PJ/yr of energy in their processes. Over the past decade, significant progress has been made towards the reduction of energy consumption and reduction of greenhouse gases in Kwinana. One way to further advance sustainable energy use is through the realisation of regional synergies. These concern the capture, recovery and reuse of by-products, water and energy between industries in close proximity. Kwinana is recognised as a leading edge example in regional synergy development, but more synergy opportunities appear to exist. The centre for sustainable resource processing (CSRP) is undertaking research to develop new synergies in Kwinana, including energy utility synergies. As part of the research, a methodology was developed and applied to identify and evaluate the economic, technical, and environmental feasibility of collaborative energy recovery opportunities from industry flue gases in Kwinana. The trial application demonstrated the significant potential to mitigate CO 2 emissions through energy recovery from flue gases by applying technologies to convert the embedded energy into useful thermal and electric applications. This article discusses the methodology and outcomes from the trial applications, including the impact of carbon taxes, reducing costs of emerging technologies, and increasing energy prices

One unit-cell seed layer induced epitaxial growth of heavily nitrogen doped anatase TiO{sub 2} films

Energy Technology Data Exchange (ETDEWEB)

Chen, T L; Hirose, Y; Hitosugi, T; Hasegawa, T [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan)], E-mail: chen@ksp.or.jp

2008-03-21

We present a novel way to obtain heavily nitrogen doped anatase TiO{sub 2} films by using a solid-state nitrogen source. Epitaxial growth of the films was realized by introducing one unit-cell seed layer, which was indicated by reflection high-energy electron diffraction as intensity oscillation. Results of x-ray diffraction and x-ray photoelectron spectroscopy confirmed that the films were in the anatase phase heavily doped with nitrogen of {approx}15 at%. The films obtained exhibited considerable narrowing of the optical bandgap, resulting in an enhancement of absorption in the visible-light region. (fast track communication)

High-temperature ferromagnetism in heavily Fe-doped ferromagnetic semiconductor (Ga,Fe)Sb

International Nuclear Information System (INIS)

Tu, Nguyen Thanh; Hai, Pham Nam; Anh, Le Duc; Tanaka, Masaaki

2016-01-01

We show high-temperature ferromagnetism in heavily Fe-doped ferromagnetic semiconductor (Ga_1_−_x,Fe_x)Sb (x = 23% and 25%) thin films grown by low-temperature molecular beam epitaxy. Magnetic circular dichroism spectroscopy and anomalous Hall effect measurements indicate intrinsic ferromagnetism of these samples. The Curie temperature reaches 300 K and 340 K for x = 23% and 25%, respectively, which are the highest values reported so far in intrinsic III-V ferromagnetic semiconductors.

Einstein's photoemission emission from heavily-doped quantized structures

CERN Document Server

Ghatak, Kamakhya Prasad

2015-01-01

This monograph solely investigates the Einstein's Photoemission(EP) from Heavily Doped(HD) Quantized Structures on the basis of newly formulated electron dispersion laws. The materials considered are quantized structures of HD non-linear optical, III-V, II-VI, Ge, Te, Platinum Antimonide, stressed materials, GaP, Gallium Antimonide, II-V, Bismuth Telluride together with various types of HD superlattices and their Quantized counterparts respectively. The EP in HD opto-electronic materials and their nanostructures is studied in the presence of strong light waves and intense electric fields  that control the studies of such quantum effect devices. The suggestions for the experimental determinations of different important physical quantities in HD 2D and 3D materials  and the importance of measurement of band gap in HD optoelectronic materials under intense built-in electric field in nano devices and strong external photo excitation (for measuring   physical properties in the presence of intense light waves w...

Industry wins, loses in House bill

International Nuclear Information System (INIS)

Anon.

1992-01-01

This paper reports that the House of Representatives has approved a plan to limit U.S. gas prorationing by the states but rejected a move to require petroleum refiners and importers to place 1% of their oil or products volumes into the Strategic Petroleum Reserve. The oil industry lobbied heavily against the SPR provision, which went down 263-135. The House then passed its omnibus energy bill 381-37. It is designed to facilitate all types of energy production while promoting conservation. The legislation also imposes bans on offshore leasing but gives independent producers limited relief from the alternative minimum tax (AMT) and does not include a mandate for use of ethanol in gasoline

Ameliorating effects of industrial sugar residue on the Jales gold mine spoil NE Portugal) using Holcus lanatus and Phaseolus vulgaris as indicators.

NARCIS (Netherlands)

Bleeker, P.M.; Teiga-Santos, M.H.; de Koe, T.; Verkley, J.A.C.

2003-01-01

Phytostabilisation of bare heavily contaminated substrate, such as abandoned mine sites, is considered a very appropriate technology in order to diminish erosion and dispersion of contaminants into the surroundings. In this short-term pot study, application of industrial sugar residue (ISR), a waste

The ARIPAR project: analysis of the major accident risks connected with industrial and transportation activities in the Ravenna area

International Nuclear Information System (INIS)

Egidi, Demetrio; Foraboschi, Franco P.; Spadoni, Gigliola; Amendola, Aniello

1995-01-01

The paper describes the ARIPAR project aimed at the assessment of the major accident risks connected with storage, process and transportation of dangerous substances in the densely populated Ravenna area in Italy, which includes a large complex of chemical and petrochemical plants and minor industries, essentially distributed around an important commercial port. Large quantities of dangerous goods are involved in various transportation forms connected with the industrial and commercial activity of the port. The project started by making a complete inventory of fixed installations and transportation activities capable of provoking major fire, explosion and toxic release events; then relevant accident scenarios were developed for the single hazard sources; probabilities were assigned to the events and consequences were evaluated; finally iso-risk contours and F-N diagrams were evaluated both for the single sources and for the overall area. This required the development of a particular methodology for analysis of area risk and of associated software packages which allowed examination of the relative importance of the different activities and typologies of materials involved. The methodological approach and the results have proved to be very useful for the priority-ranking of risk mitigating interventions and physical planning in a complex area

The U.S. Automobile Industry: Will It Survive Increasing International Competition

Science.gov (United States)

1991-04-22

the small car sales prize with its Escort. In model year 1991 Ford introduced a new Escort. The new Escort borrows heavily 54 from Mazda to include the...by Chrysler, Ford and General Motors to transition from the post World War II period through the 1973 oil crisis to the present, and examine the...Auto Industry In 1903 Henry Ford founded the Ford Motor Company. Ford was born on a farm in Dearborn Michigan to Irish immigrant parents. The Ford

Long-Term Stability of Oxide Nanowire Sensors via Heavily Doped Oxide Contact.

Science.gov (United States)

Zeng, Hao; Takahashi, Tsunaki; Kanai, Masaki; Zhang, Guozhu; He, Yong; Nagashima, Kazuki; Yanagida, Takeshi

2017-12-22

Long-term stability of a chemical sensor is an essential quality for long-term collection of data related to exhaled breath, environmental air, and other sources in the Internet of things (IoT) era. Although an oxide nanowire sensor has shown great potential as a chemical sensor, the long-term stability of sensitivity has not been realized yet due to electrical degradation under harsh sensing conditions. Here, we report a rational concept to accomplish long-term electrical stability of metal oxide nanowire sensors via introduction of a heavily doped metal oxide contact layer. Antimony-doped SnO 2 (ATO) contacts on SnO 2 nanowires show much more stable and lower electrical contact resistance than conventional Ti contacts for high temperature (200 °C) conditions, which are required to operate chemical sensors. The stable and low contact resistance of ATO was confirmed for at least 1960 h under 200 °C in open air. This heavily doped oxide contact enables us to realize the long-term stability of SnO 2 nanowire sensors while maintaining the sensitivity for both NO 2 gas and light (photo) detections. The applicability of our method is confirmed for sensors on a flexible polyethylene naphthalate (PEN) substrate. Since the proposed fundamental concept can be applied to various oxide nanostructures, it will give a foundation for designing long-term stable oxide nanomaterial-based IoT sensors.

INAA for the characterization of airborne particulate matter from the industrial area of Islamabad city

International Nuclear Information System (INIS)

Wasim, M.; Rahman, A.; Waheed, S.; Daud, M.; Ahmad, S.

2003-01-01

Air particulate matter (PM) was collected in two size fractions using stacked filter units (SFUs) provided by the International Atomic Energy Agency (IAEA) from the industrial area of Islamabad. Nucleopore polycarbonate filters were used for collecting from Oct 98 to Jun 99 the particulate matter in coarse and fine size fractions. The samples were characterized by the instrumental neutron activation analysis (INAA). About 33 elements were quantified using different irradiation and counting protocols. (author)

Dissolved organic carbon in rainwater from areas heavily impacted by sugar cane burning

Science.gov (United States)

Coelho, C. H.; Francisco, J. G.; Nogueira, R. F. P.; Campos, M. L. A. M.

This work reports on rainwater dissolved organic carbon (DOC) from Ribeirão Preto (RP) and Araraquara over a period of 3 years. The economies of these two cities, located in São Paulo state (Brazil), are based on agriculture and related industries, and the region is strongly impacted by the burning of sugar cane foliage before harvesting. Highest DOC concentrations were obtained when air masses traversed sugar cane fields burned on the same day as the rain event. Significant increases in the DOC volume weighted means (VWM) during the harvest period, for both sites, and a good linear correlation ( r = 0.83) between DOC and K (a biomass burning marker) suggest that regional scale organic carbon emissions prevail over long-range transport. The DOC VWMs and standard deviations were 272 ± 22 μmol L -1 ( n = 193) and 338 ± 40 μmol L -1 ( n = 80) for RP and Araraquara, respectively, values which are at least two times higher than those reported for other regions influenced by biomass burning, such as the Amazon. These high DOC levels are discussed in terms of agricultural activities, particularly the large usage of biogenic fuels in Brazil, as well as the analytical method used in this work, which includes volatile organic carbon when reporting DOC values. Taking into account rainfall volume, estimated annual rainwater DOC fluxes for RP (4.8 g C m -2 yr -1) and Araraquara (5.4 g C m -2 yr -1) were close to that previously found for the Amazon region (4.8 g C m -2 yr -1). This work also discusses whether previous calculations of the global rainwater carbon flux may have been underestimated, since they did not consider large inputs from biomass combustion sources, and suffered from a possible analytical bias.

Guidelines for planning interventions against external exposure in industrial area after a nuclear accident. Pt. 1. A holistic approach of countermeasure application

International Nuclear Information System (INIS)

Eged, K.; Kis, Z.; Andersson, K.G.; Roed, J.; Varga, K.

2003-01-01

Following a large-scale release of radioactivity into the environment, different urban, industrial and rural environments may be contaminated for many years. Currently, there is limited systematic consideration of long-term management to ensure sustainability of areas contaminated by long-lived radionuclides. To sustain acceptable living and working conditions in such areas it is important to be able to construct robust, effective restoration strategies which address the many different types of environment, land use and ways of life. The overall objective of the STRATEGY project (directly addressing Key Action 2: Nuclear Fission - Off-site emergency management in the Fifth Framework Programme) is to establish a decision framework to enable the selection of robust and practicable remediation strategies for Member States, which enable the long-term sustainable management of contaminated areas. The special objectives of the work carried out by GSF - Radiation Protection Institute and presented in this report was to contribute to the different urban/industrial parts of the STRATEGY project. Countermeasures being different from the usual urban ones and largely applicable in industrial area are collected and evaluated. The industrial area is defined here as such an area where productive and/or commercial activity is carried out. A good example is a supermarket or a factory. In designing restoration strategies to ensure the long-term sustainability of large and varied contaminated areas, there is a requirement to adopt a more holistic approach rather than simply selecting cost-effective countermeasures. The potentially negative consequences of restoration must be fully considered. The implementation of a remediation strategy may lead to a reduced collective dose, but increased dose to those implementing the strategies. Countermeasures may themselves generate waste and the practical consideration of disposal options has to be addressed. There is also a requirement that the

Self-Assembled Formation of Well-Aligned Cu-Te Nano-Rods on Heavily Cu-Doped ZnTe Thin Films

Science.gov (United States)

Liang, Jing; Cheng, Man Kit; Lai, Ying Hoi; Wei, Guanglu; Yang, Sean Derman; Wang, Gan; Ho, Sut Kam; Tam, Kam Weng; Sou, Iam Keong

2016-11-01

Cu doping of ZnTe, which is an important semiconductor for various optoelectronic applications, has been successfully achieved previously by several techniques. However, besides its electrical transport characteristics, other physical and chemical properties of heavily Cu-doped ZnTe have not been reported. We found an interesting self-assembled formation of crystalline well-aligned Cu-Te nano-rods near the surface of heavily Cu-doped ZnTe thin films grown via the molecular beam epitaxy technique. A phenomenological growth model is presented based on the observed crystallographic morphology and measured chemical composition of the nano-rods using various imaging and chemical analysis techniques. When substitutional doping reaches its limit, the extra Cu atoms favor an up-migration toward the surface, leading to a one-dimensional surface modulation and formation of Cu-Te nano-rods, which explain unusual observations on the reflection high energy electron diffraction patterns and apparent resistivity of these thin films. This study provides an insight into some unexpected chemical reactions involved in the heavily Cu-doped ZnTe thin films, which may be applied to other material systems that contain a dopant having strong reactivity with the host matrix.

High-temperature ferromagnetism in heavily Fe-doped ferromagnetic semiconductor (Ga,Fe)Sb

Energy Technology Data Exchange (ETDEWEB)

Tu, Nguyen Thanh [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Department of Physics, Ho Chi Minh City University of Pedagogy, 280, An Duong Vuong Street, District 5, Ho Chi Minh City 748242 (Viet Nam); Hai, Pham Nam [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro, Tokyo 152-0033 (Japan); Center for Spintronics Research Network (CSRN), The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Anh, Le Duc [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Tanaka, Masaaki [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Center for Spintronics Research Network (CSRN), The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan)

2016-05-09

We show high-temperature ferromagnetism in heavily Fe-doped ferromagnetic semiconductor (Ga{sub 1−x},Fe{sub x})Sb (x = 23% and 25%) thin films grown by low-temperature molecular beam epitaxy. Magnetic circular dichroism spectroscopy and anomalous Hall effect measurements indicate intrinsic ferromagnetism of these samples. The Curie temperature reaches 300 K and 340 K for x = 23% and 25%, respectively, which are the highest values reported so far in intrinsic III-V ferromagnetic semiconductors.

Physiological and chemical response of lichens transplanted in and around an industrial area of south Italy: relationship with the lichen diversity.

Science.gov (United States)

Paoli, Luca; Pisani, Tommaso; Guttová, Anna; Sardella, Giovanni; Loppi, Stefano

2011-05-01

The lichen Evernia prunastri (L.) Ach. has been exposed for 3 months in and around an industrial area of Mediterranean Italy for monitoring physiological (photosynthetic efficiency, membrane lipids peroxidation and cell membrane integrity) and chemical (bioaccumulation of the heavy metals Cr, Ni, Pb, V and Zn) effects and investigate the consistency with the environmental quality status depicted by the diversity of epiphytic lichens (index of lichen diversity (ILD)). The results showed that thalli transplanted close to the industrial area exhibited early stress symptoms, as revealed by the increase in electrical conductivity indicating a damage endured by lichen cell membranes. The electrical conductivity was inversely correlated with the diversity of epiphytic lichens recorded at the same sites. The ILD negatively correlated also with membrane lipid peroxidation and the rate of accumulation of Pb, V and Zn. Reciprocal correlations found among trace elements pinpointed vehicular traffic and metal processing in the industrial area as main sources. The damage endured by cell membranes was the best physiological indicator consistent with the air quality status depicted by the diversity of epiphytic lichens. Copyright © 2010 Elsevier Inc. All rights reserved.

Contamination of soil and the medicinal plant Phyllanthus niruri Linn. with cadmium in ceramic industrial areas.

Science.gov (United States)

Santos, Vanessa Santana Vieira; Arantes, Karen Magalhães; Gonçalves, Ester Luiza; Campos, Carlos Fernando; de Campos Júnior, Edimar Olegário; de Oliveira, Antônio Marcos Machado; Pereira, Boscolli Barbosa

2018-04-22

Phyllanthus niruri is a plant that is used to prevent calcium oxalate crystallisation and to block the stone formation in urolithiasis. Contaminants in the environment can be readily taken up by medicinal plants due to their ability to absorb chemicals into their tissues. If contaminated plants are ingested, they have the potential to negatively affect human and environmental health. The aim of this study was to assess contamination in the soil and the medicinal plant P. niruri by cadmium (Cd) in ceramic industrial areas of Monte Carmelo, Brazil. Soil samples and plant samples (divided in root, shoot and leaves) were collected from a contaminated monitoring site and from a rural area (which was used as a reference site for comparative purposes). The Cd concentrations of the samples were analysed with an atomic absorption spectrometer. P. niruri was found to be sensitive to soil contamination by Cd that was attributed to ceramic industrial emissions. The results revealed that Cd bioaccumulation in the roots and shoots of P. niruri was associated with a significant increase (p risk of contamination of the site and the risk of a high dose of Cd to people exposed at the site.

Becoming a Heavily Tattooed Young Body: From a Bodily Experience to a Body Project

Science.gov (United States)

Ferreira, Vitor Sérgio

2014-01-01

Why some young people start to tattoo their bodies? And why some of them keep going on with this practice, until having all body tattooed? What doing so means to them? These are some of the questions that underlie a qualitative research project carried out in Portugal on heavily tattooed young people. In this article, the author discusses their…

Industrialization Impact on Worker Mobility and Land Use in Peri Urban Area (Case study of Semarang District, Indonesia)

Science.gov (United States)

Wijaya, H. B.; Kurniawati, H.; Hutama, S. T. E. W.

2018-02-01

In many cases, industrialization has stimulated the urbanization process massively. It tends to attract substantial number of labor migrants from nearby region to fulfill the demand of workers. The paper reports the research result of industrialization phenomena in Semarang district, Indonesia. It carried out the survey by taking 250 samples of migrant workers. The result shows that the presence of labor-intensive industries becomes the most influence factor for many migrants, rather than the driving factors from the place of origin. The attraction factor could cover regional and across the province force, as indicated that all migrant respondents come from both inside and outside of Central Java Province. Furthermore, based on the land-use distribution of the migrant settlement area, it indicates a growing land-use change, both of land cover and land functions.

Scientific and technological capabilities in health-related areas: opportunities, challenges, and interactions with the industrial sector.

Science.gov (United States)

Vargas, Marco Antonio; Britto, Jorge

2016-11-03

Characterization of the scientific and technological infrastructure in health and its interactions with the industrial sector provides key elements for understanding the dynamics of innovation in health. This study conducts an exploratory analysis of the potentialities and limitations associated with scientific and technological capabilities in the health area in Brazil and the different links between the scientific and industrial sectors in health. The analysis points to important growth in internationally indexed research output, especially in certain areas such as pharmaceutics, public health, genetics, morphology, physiology, and microbiology. There has also been important growth in research groups that interact with the industrial sector in selected areas of health. The study highlights the importance of building more solid and permanent bridges between companies, research institutions, and the health system, linking the knowledge developed in research institutions to the dynamics of the industrial sector in health. Resumo: A caracterização da infraestrutura científica e tecnológica na área da saúde e das suas formas de articulação com a base produtiva representam elementos centrais na compreensão da dinâmica de inovação em saúde. Este estudo faz uma análise exploratória sobre as potencialidades e limitações associadas às capacitações científicas e tecnológicas na área da saúde no Brasil e as formas de articulação entre a base científica e a base produtiva em saúde. A análise aponta para o crescimento expressivo da produção bibliográfica com circulação internacional no campo da saúde, particularmente em determinadas áreas como farmácia, saúde coletiva, genética, morfologia, fisiologia e microbiologia. Além disso, observa-se um crescimento expressivo dos grupos de pesquisa com relacionamentos com o setor produtivo em áreas selecionadas da saúde. Destaca-se a importância da construção de pontes mais sólidas e

New support impulse in the area of industrial robots

International Nuclear Information System (INIS)

Martin, T.

1982-06-01

On this workshop problems of industrial robots were discussed by suppliers, users, and scientists. Such robots are used for handling workpieces and tools in the industry producing goods. Starting out from describing the state-of-the-art and latest experiences, development deficits are identified in detail. This includes hardware and software specifics as well as handling oriented product design and methods and tools for systems planning. (orig.) [de

Spatial gradient of human health risk from exposure to trace elements and radioactive pollutants in soils at the Puchuncaví-Ventanas industrial complex, Chile.

Science.gov (United States)

Salmani-Ghabeshi, S; Palomo-Marín, M R; Bernalte, E; Rueda-Holgado, F; Miró-Rodríguez, C; Cereceda-Balic, F; Fadic, X; Vidal, V; Funes, M; Pinilla-Gil, E

2016-11-01

The Punchuncaví Valley in central Chile, heavily affected by a range of anthropogenic emissions from a localized industrial complex, has been studied as a model environment for evaluating the spatial gradient of human health risk, which are mainly caused by trace elemental pollutants in soil. Soil elemental profiles in 121 samples from five selected locations representing different degrees of impact from the industrial source were used for human risk estimation. Distance to source dependent cumulative non-carcinogenic hazard indexes above 1 for children (max 4.4 - min 1.5) were found in the study area, ingestion being the most relevant risk pathway. The significance of health risk differences within the study area was confirmed by statistical analysis (ANOVA and HCA) of individual hazard index values at the five sampling locations. As was the dominant factor causing unacceptable carcinogenic risk levels for children (sampling locations which are closer to the industrial complex, whereas the risk was just in the tolerable range (10 -6 - 10 -4 ) for children and adults in the rest of the sampling locations at the study area. Furthermore, we assessed gamma ray radiation external hazard indexes and annual effective dose rate from the natural radioactivity elements ( 226 Ra, 232 Th and 40 K) levels in the surface soils of the study area. The highest average values for the specific activity of 232 Th (31 Bq kg -1 ), 40 K (615 Bq kg - 1 ), and 226 Ra (25 Bq kg -1 ) are lower than limit recommended by OECD, so no significant radioactive risk was detected within the study area. In addition, no significant variability of radioactive risk was observed among sampling locations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Implementation of new legislative measures on industrial risks prevention and control in urban areas

International Nuclear Information System (INIS)

Cahen, Bruno

2006-01-01

Incompatible at first sight, but vital to each other, the industry and the city have been developing a complex relationship for decades. From 1810 on in France, risk prevention and control in and around major industrial sites evolves step-by-step, learning from accidents. Land-use planning in the vicinity of SEVESO establishments becomes one of the key policies in the prevention of major industrial accident hazard on European level in 1996, focussing on historical situation of concern [M.D. Christou, S. Porter, Guidance on Land-use Planning as required by the Council Directive 96/82/EC. Joint Research Centre, European Commission, 1999]. The Toulouse (F) accidents, on 21 September 2001 evidenced the need for new tools to reinforce protective action and ease the situation of clusters of factories engulfed in the urban setting. In France, new legislative measures adopted on 30 July 2003 deeply modified the approach to land-use planning around the main dangerous facilities (622 establishments). The implementation of technological risk prevention plans [Fr. 'PPRT'] will limit the exposition of the population to the consequences of accidents. These plans, derived from the risk assessment (safety reports) produced by the operators of the hazardous facilities, will delineate areas within which requirements can be imposed on existing and future buildings and within which future building rights may be restricted. On the grounds of extremely serious danger that threatens human life, pre-existing constructions may be progressively expropriated. The financing of the corresponding measures, estimated a rough -bar 2-4 billions, will be defined by agreements among the Central Government, the industrial company and the local and regional bodies

An approach to detecting delayed effects of radioactive contamination on industrial-urban-area dwellers

International Nuclear Information System (INIS)

Privalova, L.I.; Katsnelson, B.A.; Polzik, E.V.; Kazantsev, V.S.; Lipatov, G.Ya.; Beikin, Y.B.

1994-01-01

Detecting changes in humans that result from radioactive contamination of the area of residence many years after an incident (i.e., when the radiation has substantially decayed) presents a difficult epidemiological problem. Problems of this kind are even more complicated in areas where the population is continually exposed to other harmful man-made factors. The city of Kamensk-Uralsky (Sverdlovsk region, Russia) is a good case in point. In 1957, part of Kamensk-Uralsky was contaminated as the result of an accident at the Kyshtym nuclear plant. In addition, the population of the contaminated area is being exposed to atmospheric emissions from several industrial enterprises. Two comparable groups of residents were formed: one in the contaminated area and another in a control area within the same city characterized by similar levels of chemical pollution but substantially lower radioactive contamination. The groups were composed of only those people who had been living in these areas continually since time of the accident and who were under 15 years of age at the time of the accident. The groups were matched by sex, age, and socio-occupational characteristics. For each subject, data were gathered on more than 50 parameters including hematological, immunological, and biochemical indices of the health status. All these data were obtained from blood tests taken in the fall of 1992. Data processing was carried out with the help of a computerized mathematical pattern recognition methodology, which ensured reliable discrimination between the generalized health status in the areas under study. We found that the health status of inhabitants of the area more contaminated with radioactive fallouts were adversely affected by radiation

Evaluating environmental impact caused by industrial activities - Implementation of the WTP-WTA approach

Science.gov (United States)

Kopsidas, Odysseas; Batzias, Fragiskos

2012-12-01

In this work, a methodological framework under the form of an algorithmic procedure, including 28 activity stages and 6 decision nodes, has been developed for evaluating environmental impact caused by industrial activities. The main part of this procedure is a modification of the Contingent Valuation Method (CVM), which is heavily relied on survey-based estimation of WTP-WTA (willingness to pay/accept, respectively). The survey may take place either under a strictly controlled environment or in situ and as-is ('laboratory conditions' or 'field conditions', respectively, in the terminology of experimental economics). Implementation of this methodology is presented, referring to three cases of industrial pollution (in three different sites) caused by (i) a cement producing units, (ii) an oil refinery complex, and (iii) an industrialized small city with an intensively polluted port, where several industrial units co-exist, all of them located in the vicinity of Athens, Greece. The results are interpreted/discussed and conclusions are drawn.

Infant mortality in the Federal Republic of Germany in the years after Chernobyl. Study into the influence of the Chernobyl reactor accident in April 1986 on infant mortality in lightly and heavily contaminated areas of the Federal Republic of Germany. Saeuglingssterblichkeit nach Tschernobyl in der BRD. Untersuchung der Auswirkungen des Reaktorunfalls von Tschernobyl im April 1986 auf die Saeuglingssterblichkeit in schwach- und hochbelasteten Gebieten der Bundesrepublik Deutschland

Energy Technology Data Exchange (ETDEWEB)

Martini, W; Scholz, H; Hacker, C; Beushausen, S; Heydenreich, B; Platiel, G

1991-04-01

Study into the influence of the Chernobyl reactor accident in April 1986 on infant mortility in lightly and heavily contaminated areas of the Federal Republic of Germany. In connection with this scientific study, official quarterly reports on population developments released by the Wiesbaden-based Federal Office of Statistics were subjected to a time-dependent analysis. On the basis of generally applicable stastical laws infant mortality curves plotted after 1958 were examined for changes after Chernobyl. In view of regional differences in the effects from radioactive precipitations due to the Chernobyl ractor accident, the examinations were performed in subgroups that were largely derived from the results of a study covering all of the Federal territory. The analysis revealed the following links: The curve of the infant mortality rates for the first 7 days after delivery (7-day mortalities) pointed to a linear-exponential relationship between the point of time investigated and number of infants dying. In heavily contaminated areas the 7-day mortality rates determined after 1986 show statistically significant deviations from developments as expected from normal rates. (orig./MG).

Sustainable industrial estate by managing the building coverage ratio in Cibitung Industrial Town, Indonesia

Science.gov (United States)

Budiyanto, T. M. T.; Prajitno, I. S.; Hasibuan, H. S.

2018-03-01

The problem faced in the management of the industrial estate is the development of industrial buildings which are not in accordance with the existing environmental regulations, especially the building coverage ratio (BCR). This violation is due to the limitation of industrial land owned, and the tenant’s desire to maximize building area. This research conducted at Cibitung Industrial Town, Indonesia, to assess the compliance of industrial building in complying with environmental regulations, and efforts by industrial estate manager together with industrial communities to meet building regulations. The compliance is shown from the conformity of the tenant’s BCR to the building provisions contained in the regulation within the industrial estate; which is maximum 60% from land owned. And whether the rest of green open space (GOS) area can still be maintained at a minimum 10%. This study found tenant’s building density (BCR) at 24.55% population was 84.77%, and the rest of green open space at 21.56% population was only 2.49%. Excessive building development and expansion by the industrial communities, led to a continued reduction in green open space as a rainwater absorption area. It is resulting the rainfall runoff directly into the environmental drainage system, and causing flooding in the region.

Rapid enhancement of nodal quasiparticle mass with heavily underdoping in Bi2212

Science.gov (United States)

Anzai, Hiroaki; Arita, Masashi; Namatame, Hirofumi; Taniguchi, Masaki; Ishikado, Motoyuki; Fujita, Kazuhiro; Ishida, Shigeyuki; Uchida, Shin-ichi; Ino, Akihiro

2018-05-01

We report substantial advance of our low-energy angle-resolved photoemission study of nodal quasiparticles in Bi2Sr2CaCu2O8+δ. The new data cover the samples from underdoped down to heavily underdoped levels. We also present the nodal Fermi velocities that determined by using an excitation-photon energy of hν = 7.0 eV over a wide doping range. The consistency between the results with hν = 8.1 and 7.0 eV allows us to rule out the effect of photoemission matrix elements. In comparison with the data previously reported, the nodal effective mass increases by a factor of ∼ 1.5 in going from optimally doped to heavily underdoped levels. We find a rapid enhancement of the nodal quasiparticle mass at low doping levels near the superconductor-to-insulator transition. The effective coupling spectrum, λ (ω) , is extracted directly from the energy derivatives of the quasiparticle dispersion and scattering rate, as a causal function of the mass enhancement factor. A steplike increase in Reλ (ω) around ∼ 65 meV is demonstrated clearly by the Kramers-Kronig transform of Imλ (ω) . To extract the low-energy renormalization effect, we calculated a simple model for the electron-boson interaction. This model reveals that the contribution of the renormalization at | ω | ≤ 15 meV to the quasiparticle mass is larger than that around 65 meV in underdoped samples.

Effects of satellite image spatial aggregation and resolution on estimates of forest land area

Science.gov (United States)

M.D. Nelson; R.E. McRoberts; G.R. Holden; M.E. Bauer

2009-01-01

Satellite imagery is being used increasingly in association with national forest inventories (NFIs) to produce maps and enhance estimates of forest attributes. We simulated several image spatial resolutions within sparsely and heavily forested study areas to assess resolution effects on estimates of forest land area, independent of other sensor characteristics. We...

An accurate measurement of the baryonic Tully-Fisher relation with heavily gas-dominated ALFALFA galaxies

NARCIS (Netherlands)

Papastergis, E.; Adams, E. A. K.; van der Hulst, J. M.

2016-01-01

We use a sample of 97 galaxies selected from the Arecibo legacy fast ALFA (ALFALFA) 21 cm survey to make an accurate measurement of the baryonic Tully-Fisher relation (BTFR). These galaxies are specifically selected to be heavily gas-dominated (Mgas/M∗ ≳ 2.7) and to be oriented edge-on. The former

Blood biomonitoring of metals in subjects living near abandoned mining and active industrial areas.

Science.gov (United States)

Madeddu, Roberto; Tolu, Paola; Asara, Yolande; Farace, Cristiano; Forte, Giovanni; Bocca, Beatrice

2013-07-01

A human blood biomonitoring campaign to detect the environmental exposure to metals (Cd, Cu, Cr, Mn, Pb and Zn) in 265 subjects was performed in the South-Western part of Sardinia (an Italian island) that is a particular area with a great history of coal and metal mining (Pb/Zn mainly) activities and large industrial structures (as metallurgy). Subjects living near the industrial plant area had geometric means (GM) of blood Cd (0.79 μg/l), Cu (971 μg/l), Mn (12.2 μg/l), and Pb (55.7 μg/l) significantly higher than controls (Cd, 0.47 μg/l; Cu, 900 μg/l; Mn 9.98 μg/l; Pb, 26.5 μg/l) and than people living nearby the past mining sites. Subjects living next to one dismissed mine were statistically higher in blood Cu (GM, 1,022 μg/l) and Pb (GM, 41.4 μg/l) concentrations than controls. No differences were observed in people living in the different mining sites, and this might be related to the decennial disclosure of mines and the adoption of environmental remediation programmes. Some interindividual variables influenced blood biomonitoring data, as smoke and age for Cd, gender for Cu, age, sex and alcohol for Pb, and age for Zn. Moreover, blood metal levels of the whole population were similar to reference values representative of the Sardinian population and acceptably safe according to currently available health guidelines.

Using Storyboarding Techniques to Identify Design Opportunities: When Students Employ Storyboards, They Are Better Able to Understand the Complexity of a Products's Use and Visualize Areas for Improvement

Science.gov (United States)

Reeder, Kevin

2005-01-01

The movie industry heavily relies on storyboards as an effective way to visually describe the process of a movie. The storyboard visually describes how the movie flows from beginning to end, how the characters are interacting, and where transitions and/or gaps exist in the storyline. The storyboard is an effective tool in industrial design as…

Gastric and colorectal cancer mortality in an urban and industrialized area of Brazil Mortalidade por cânceres gástrico e colorretal em uma área urbana-industrial do Brasil

Directory of Open Access Journals (Sweden)

Marcilia de Araujo Medrado-Faria

2001-04-01

Full Text Available PURPOSE: To study the gastric and colorectal cancer mortalities and their relation to the urban-industrialization in Baixada Santista, located in the southeastern region of Brazil. METHODS: Selected from the registries of the State System of Data Analysis Foundation (SEADE were 1105 deaths due to gastric cancer (ICD 153--154 and 690 due to colorectal cancer (ICD 151 that occurred from 1980 to 1993 in males, above 10 years of age, residing in Baixada Santista. For each of these types of cancer, the standardized mortality rates, age-adjusted by world population in the 1960s, for 4 industrialized and 4 non-industrialized urban communities in that region were calculated. The ratios among those rates were calculated in order to compare the mortality in the periods 1980--93, 1980--1986, and 1987--1993. RESULTS: Standardized mortality rates for colorectal cancer were significantly higher in industrialized area, with ratios of 1.6 [95% CI 1.22 -- 2.29], 1.6 [95% CI 1.2 -- 2.0], and 1.6 [95% CI 1.3 -- 2.0] in the periods 1980--86, 1987--1993 and 1980--93, respectively. Gastric cancer did not show any statistical difference between the industrialized and non-industrialized areas, but there was a significant decrease in BS from the period 1980--1986 to 1987--1993. CONCLUSIONS: The significant elevation of colorectal cancer mortality in the industrialized area could be related to exposure to numerous carcinogens such as aromatic hydrocarbon, organic-chloride, metals, and industrial-port dust present in the region. Alternatively, the non-significant difference in gastric cancer between industrialized and non-industrialized areas and significant decrease in the last few years could be predominately reflecting the advances in the quality of life in urban areas. These results require further case-control studies that could help with the analysis of the associations among cancer and environmental factors (occupational, urban-industrial, habit, and life condition

Polycyclic aromatic hydrocarbons (PAHs) in a large South American industrial coastal area (Santos Estuary, Southeastern Brazil): Sources and depositional history

International Nuclear Information System (INIS)

Martins, Cesar C.; Bicego, Marcia C.; Mahiques, Michel M.; Figueira, Rubens C.L.; Tessler, Moyses G.; Montone, Rosalinda C.

2011-01-01

Highlights: → In early 1980s, Santos Estuary became known as one of the worst polluted in the world. → PAHs levels were similar to the values reported for marine sediments worldwide. → PAHs analyses indicated multiple sources of these compounds (oil and pyrolitic origin). → The decline of oil consumption due to the world oil crisis (late 1970s) was shown. → The input of organic pollutants is a historical problem for the Santos Estuary. - Abstract: Located in southeastern Brazil, the Santos Estuary has the most important industrial and urban population area of South America. Since the 1950's, increased urbanization and industrialization near the estuary margins has caused the degradation of mangroves and has increased the discharge of sewage and industrial effluents. The main objectives of this work were to determine the concentrations and sources of polycyclic aromatic hydrocarbons (PAHs) in sediment cores in order to investigate the input of these substances in the last 50 years. The PAHs analyses indicated multiple sources of these compounds (oil and pyrolitic origin), basically anthropogenic contributions from biomass, coal and fossil fuels combustion. The distribution of PAHs in the cores was associated with the formation and development of Cubatao industrial complex and the Santos harbour, waste disposal, world oil crisis and the pollution control program, which results in the decrease of organic pollutants input in this area.

  Transformation of the industrial harbor areas to housing areas

DEFF Research Database (Denmark)

Rehder, Meike

2009-01-01

Research question: How to read the universal (understood as the common and the social) and the individual (understood as the specific, private and intimate) in the meeting between urban and housing space? Questions in the project: How do the exterior spaces in these new harbour areas come to being......? What influences are at play in the development of them? What influences the approval and the functioning of these housing areas?...

Effect of mercury and arsenic from industrial effluents on the drinking water and comparison of the water quality of polluted and non-polluted areas: a case study of Peshawar and Lower Dir.

Science.gov (United States)

Ishaq, M; Jan, F Akbar; Khan, Murad Ali; Ihsanullah, I; Ahmad, I; Shakirullah, M; Roohullah

2013-02-01

The purpose of the present study was to find out the sources of mercury and arsenic pollution of water in the industrial area of Peshawar, the capital of Khyber Pakhtunkhwa, Pakistan. Samples of effluents, mud, and water were collected from the target area (industrial area of Peshawar), the area of water supply source, and from the less polluted area, the Lower Dir district, as the control. Hg was determined by the cold vapor generation technique, while arsenic was determined using the electrothermal atomic absorption technique. Data of the water from the industrial area were compared with that of the source area, control area, as well as with the WHO and some international drinking water quality standards. The results show that some parameters, i.e., TDS, DO, pH, and hardness, were more than the permissible limits. Textile and glass industries were found to be the major sources of Hg and As pollution. Downstream dilution of these contaminants was also observed.

Restaurant industry preparedness against intentional food contamination: results of a South Carolina survey.

Science.gov (United States)

Xirasagar, Sudha; Kanwat, C P; Smith, Lillian U; Li, Yi-Jhen; Sros, Lekhena; Shewchuk, Richard M

2010-01-01

Food safety and food defense are both responsibilities of public health agencies. Food safety practices within restaurants are regulated by state and local public health laws based on the US Food and Drug Administration Model Food Code. However, little is known about preemptive practices against intentional food-borne outbreaks within restaurants. The researchers administered a survey to a 50 percent random sample of South Carolina's restaurants, a state that relies heavily on tourism and the restaurant industry for its economic well-being. The survey received a response rate of 15 percent. The food defense practice items fall under three functional categories: employee management and training practices; vendor and delivery-related practices; and physical facilities and operational security practices. This study presents the results, classified by geographic region. Findings indicate some key areas of vulnerability that need attention to protect the public from mass food outbreaks due to intentional contamination. Of concern, there is much variation in practices by geographic region. On the basis of the survey, recommendations are made to improve restaurant preparedness against food-borne outbreaks from terrorism and malevolent contamination.

Trends in arsenic levels in PM10 and PM 2.5 aerosol fractions in an industrialized area.

Science.gov (United States)

García-Aleix, J R; Delgado-Saborit, J M; Verdú-Martín, G; Amigó-Descarrega, J M; Esteve-Cano, V

2014-01-01

Arsenic is a toxic element that affects human health and is widely distributed in the environment. In the area of study, the main Spanish and second largest European industrial ceramic cluster, the main source of arsenic aerosol is related to the impurities in some boracic minerals used in the ceramic process. Epidemiological studies on cancer occurrence in Spain points out the study region as one with the greater risk of cancer. Concentrations of particulate matter and arsenic content in PM10 and PM2.5 were measured and characterized by ICP-MS in the area of study during the years 2005-2010. Concentrations of PM10 and its arsenic content range from 27 to 46 μg/m(3) and from 0.7 to 6 ng/m(3) in the industrial area, respectively, and from 25 to 40 μg/m(3) and from 0.7 to 2.8 ng/m(3) in the urban area, respectively. Concentrations of PM2.5 and its arsenic content range from 12 to 14 μg/m(3) and from 0.5 to 1.4 ng/m(3) in the urban background area, respectively. Most of the arsenic content is present in the fine fraction, with ratios of PM2.5/PM10 in the range of 0.65-0.87. PM10, PM2.5, and its arsenic content show a sharp decrease in recent years associated with the economic downturn, which severely hit the production of ceramic materials in the area under study. The sharp production decrease due to the economic crisis combined with several technological improvements in recent years such as substitution of boron, which contains As impurities as raw material, have reduced the concentrations of PM10, PM2.5, and As in air to an extent that currently meets the existing European regulations.

Fresh water production from municipal waste water with RO membrane technology and its application for agriculture and industry in arid area

International Nuclear Information System (INIS)

Yokoyama, F

2015-01-01

One of the biggest problems of the 21st century is the global water shortage. Therefore it is difficult to increase the quantity of conventional water resources such as surface water and groundwater for agriculture and industry in arid area. Technical advancement in water treatment membrane technology including RO membrane has been remarkable especially in recent years. As the pore size of RO membrane is less than one nanometer, it is possible to produce the fresh water, which satisfies the drinking water quality standards, with utilizing RO membrane. In this report a new fresh water resource from municipal waste water is studied to apply to the plant factory which is the water saving type agriculture and industry in arid area

Industrial Hemp in North America: Production, Politics and Potential

Directory of Open Access Journals (Sweden)

Jerome H. Cherney

2016-11-01

Full Text Available Most of the Western World banned the cultivation of Cannabis sativa in the early 20th century because biotypes high in ∆9-tetrahydrocannabinol (THC, the principal intoxicant cannabinoid are the source of marijuana. Nevertheless, since 1990, dozens of countries have authorized the licensed growth and processing of “industrial hemp” (cultivars with quite low levels of THC. Canada has concentrated on hemp oilseed production, and very recently, Europe changed its emphasis from fiber to oilseed. The USA, historically a major hemp producer, appears on the verge of reintroducing industrial hemp production. This presentation provides updates on various agricultural, scientific, social, and political considerations that impact the commercial hemp industry in the United States and Canada. The most promising scenario for the hemp industry in North America is a continuing focus on oilseed production, as well as cannabidiol (CBD, the principal non-intoxicant cannabinoid considered by many to have substantial medical potential, and currently in great demand as a pharmaceutical. Future success of the industrial hemp industry in North America is heavily dependent on the breeding of more productive oilseed cultivars, the continued development of consumer goods, reasonable but not overly restrictive regulations, and discouragement of overproduction associated with unrealistic enthusiasm. Changing attitudes have generated an unprecedented demand for the cannabis plant and its products, resulting in urgent needs for new legislative, regulatory, and business frameworks, as well as scientific, technological, and agricultural research.

Mass and elemental distributions of atmospheric particles nearby blast furnace and electric arc furnace operated industrial areas in Australia

Energy Technology Data Exchange (ETDEWEB)

Mohiuddin, Kazi, E-mail: kazi.mohiuddin@students.mq.edu.au [Graduate School of the Environment, Department of Environment and Geography, Faculty of Science, Macquarie University, NSW (Australia); Strezov, Vladimir; Nelson, Peter F. [Graduate School of the Environment, Department of Environment and Geography, Faculty of Science, Macquarie University, NSW (Australia); Stelcer, Eduard [Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Evans, Tim [Graduate School of the Environment, Department of Environment and Geography, Faculty of Science, Macquarie University, NSW (Australia)

2014-07-01

The improved understanding of mass and elemental distributions of industrial air particles is important due to their heterogeneous atmospheric behaviour and impact on human health and the environment. In this study, particles of different size ranges were collected from three sites in Australia located in the vicinity of iron and steelmaking industries and one urban background site with very little industrial influence. In order to determine the importance of the type of industrial activity on the urban atmospheric quality, the industrial sites selected in this study were in the close proximity to two blast furnace operated and one electric arc furnace based steelmaking sites. The chemical compositions of the collected air particles were analysed using the proton induced X-ray emission (PIXE) technique. This study revealed significantly higher metal concentrations in the atmospheric particles collected in the industrial sites, comparing to the background urban site, demonstrating local influence of the industrial activities to the air quality. The modality types of the particles were found to be variable between the mass and elements, and among elements in the urban and industrial areas indicating that the elemental modal distribution is as important as particle mass for particle pollution modelling. The highest elemental number distribution at all studied sites occurred with particle size of 0.1 μm. Iron was found as the main dominant metal at the industrial atmosphere in each particle size range. The industrial Fe fraction in the submicron and ultrafine size particles was estimated at up to 95% which may be released from high temperature industrial activities with the iron and steelmaking industries being one of the major contributors. Hence, these industrial elemental loadings can highly influence the atmospheric pollution at local urban and regional levels and are required to consider in the atmospheric modelling settings. - Highlights: • Urban and

Mass and elemental distributions of atmospheric particles nearby blast furnace and electric arc furnace operated industrial areas in Australia

International Nuclear Information System (INIS)

Mohiuddin, Kazi; Strezov, Vladimir; Nelson, Peter F.; Stelcer, Eduard; Evans, Tim

2014-01-01

The improved understanding of mass and elemental distributions of industrial air particles is important due to their heterogeneous atmospheric behaviour and impact on human health and the environment. In this study, particles of different size ranges were collected from three sites in Australia located in the vicinity of iron and steelmaking industries and one urban background site with very little industrial influence. In order to determine the importance of the type of industrial activity on the urban atmospheric quality, the industrial sites selected in this study were in the close proximity to two blast furnace operated and one electric arc furnace based steelmaking sites. The chemical compositions of the collected air particles were analysed using the proton induced X-ray emission (PIXE) technique. This study revealed significantly higher metal concentrations in the atmospheric particles collected in the industrial sites, comparing to the background urban site, demonstrating local influence of the industrial activities to the air quality. The modality types of the particles were found to be variable between the mass and elements, and among elements in the urban and industrial areas indicating that the elemental modal distribution is as important as particle mass for particle pollution modelling. The highest elemental number distribution at all studied sites occurred with particle size of 0.1 μm. Iron was found as the main dominant metal at the industrial atmosphere in each particle size range. The industrial Fe fraction in the submicron and ultrafine size particles was estimated at up to 95% which may be released from high temperature industrial activities with the iron and steelmaking industries being one of the major contributors. Hence, these industrial elemental loadings can highly influence the atmospheric pollution at local urban and regional levels and are required to consider in the atmospheric modelling settings. - Highlights: • Urban and

AFM of metallic nano-particles and nano-structures in heavily irradiated NaCl

OpenAIRE

Gaynutdinov, R; Vainshtein, DI; Hak, SJ; Tolstikhina, A; Den Hartog, HW

2003-01-01

AFM investigations are reported for heavily, electron irradiated NaCl crystals in ultra high vacuum (UHV) in the non-contact mode-with an UHV AFM/STM Omicron system. To avoid chemical reactions between the radiolytic Na and oxygen and water, the irradiated samples were cleaved and prepared for the experiments in UHV At the surface of freshly cleaved samples, we have observed sodium nano-precipitates with shapes, which depend on the irradiation dose and the volume fraction of the radiolytic Na...

75 FR 26967 - Guidance for Industry: Use of Water by Food Manufacturers in Areas Subject to a Boil-Water...

Science.gov (United States)

2010-05-13

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-D-0236] Guidance for Industry: Use of Water by Food Manufacturers in Areas Subject to a Boil-Water Advisory; Availability AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The Food and Drug...

Stored energy and annealing behavior of heavily deformed aluminium

DEFF Research Database (Denmark)

Kamikawa, Naoya; Huang, Xiaoxu; Kondo, Yuka

2012-01-01

It has been demonstrated in previous work that a two-step annealing treatment, including a low-temperature, long-time annealing and a subsequent high-temperature annealing, is a promising route to control the microstructure of a heavily deformed metal. In the present study, structural parameters...... are quantified such as boundary spacing, misorientation angle and dislocation density for 99.99% aluminium deformed by accumulative roll-bonding to a strain of 4.8. Two different annealing processes have been applied; (i) one-step annealing for 0.5 h at 100-400°C and (ii) two-step annealing for 6 h at 175°C...... followed by 0.5 h annealing at 200-600°C, where the former treatment leads to discontinuous recrystallization and the latter to uniform structural coarsening. This behavior has been analyzed in terms of the relative change during annealing of energy stored as elastic energy in the dislocation structure...

Air pollution and urban climate in the Rhine--Westphalian industrial area and their influence on lichen growth on trees

Energy Technology Data Exchange (ETDEWEB)

Domroes, M

1966-01-01

Lichens on tree boles were examined on 25,114 trees along streets and areas in the central part of the Ruhr District and related to air pollution concentrations. The lichens were studied with regard to physiognomy, density, and exposition, and in relation to bark characteristics of tree species. Lichens were classified into the following areas: Lichen desert, transitional zone, or area of normal distribution. The lichens were sensitive to air pollution, especially sulfur dioxide emissions. The damaging influence of the town climate, especially aridity, was taken into consideration. Lichens were missing in all areas with a high degree of air pollution. These were areas of high density housing and of lower humidity than open country. Areas which had lower housing density and lower humidity also had increased lichen damage. Lichens were missing in the immediate neighborhood of factories or industrial areas outside towns. Lichen growth was reduced along busy roads.

An exploratory study of services marketing in global markets: major areas of inquiry for the health care services industry.

Science.gov (United States)

Young, S; Erdem, S A

1996-01-01

It has been stated that one of the major challenges for the international marketer is the design of an efficient strategy for marketing services to international markets. This paper reviews some of the issues associated with services marketing in global markets along with the basic variables of service industries. An exploratory assessment of the health care services industry results in a list composed of several inquiry areas which should be examined by multinational companies. It is hoped that the review of the issues raised in this paper provides a basis for decision making and further research.

Acute effects of urban and industrial pollution in a government-designated "Environmental risk area": the case of Brindisi, Italy.

Science.gov (United States)

Gianicolo, Emilio Antonio Luca; Bruni, Antonella; Mangia, Cristina; Cervino, Marco; Vigotti, Maria Angela

2013-01-01

Exposure to air pollutants has been associated with increased hospital admissions (HAs) for respiratory and cardiovascular diseases. This work describes a short-term epidemiological study in Brindisi, a highly industrialized town in Southern Italy. The effects of daily exposure to PM10 and NO2 on daily HAs for cardiac, respiratory, and cerebrovascular diseases were investigated by means of a case-crossover design in the period 2001-2007. Results showed positive associations between PM10 and HAs for cardiac and respiratory diseases and between NO2 and HAs for all the categories of diseases considered, particularly among females. Although not statistically significant, increased risk was observed for wind blowing from the port and the industrial area. Findings confirm the health risks associated with ambient air pollution exposure, even though NO2 and PM10 concentrations were below the legal limits. This may be due to the complex scenario of emissions in the area, which should be better investigated.

The Importance of Building and Enhancing Worldwide Industry Cooperation in the Areas of Radiological Protection, Waste Management and Decommissioning

International Nuclear Information System (INIS)

Saint-Pierre, S.

2006-01-01

The slow or stagnant rate of nuclear power generation development in many developed countries over the last two decades has resulted in a significant shortage in the population of mid-career nuclear industry professionals. This shortage is even more pronounced in some specific areas of expertise such as radiological protection, waste management and decommissioning. This situation has occurred at a time when the renaissance of nuclear power and the globalization of the nuclear industry are steadily gaining momentum and when the industry's involvement in international and national debates in these three fields of expertise (and the industry's impact on these debates) is of vital importance. This paper presents the World Nuclear Association (WNA) approach to building and enhancing worldwide industry cooperation in radiological protection, waste management and decommissioning, which is manifested through the activities of the two WNA working groups on radiological protection (RPWG) and on waste management and decommissioning (WM and DWG). This paper also briefly describes the WNA's participatory role, as of summer 2005, in the International Atomic Energy Agency (IAEA) standard development committees on radiation safety (RASSC), waste safety (WASSC) and nuclear safety (NUSSC). This participation provides the worldwide nuclear industry with an opportunity to be part of IAEA's discussions on shaping changes to the control regime of IAEA safety standards. The review (and the prospect of a revision) of IAEA safety standards, which began in October 2005, makes this WNA participation and the industry ' s involvement at the national level timely and important. All of this excellent industry cooperation and team effort is done through 'collegial' exchanges between key industry experts, which help tackle important issues more effectively. The WNA is continuously looking to enhance its worldwide industry representation in these fields of expertise through the RPWG and WM and DWG

The importance of building and enhancing worldwide industry cooperation in the areas of radiological protection, waste management and decommissioning

International Nuclear Information System (INIS)

Saint-Pierre, S.

2006-01-01

The slow or stagnant rate of nuclear power generation development in many developed countries over the last two decades has resulted in a significant shortage in the population of mid-career nuclear industry professionals. This shortage is even more pronounced in some specific areas of expertise such as radiological protection, waste management and decommissioning. This situation has occurred at a time when the renaissance of nuclear power and the globalization of the nuclear industry are steadily gaining momentum and when the industry's involvement in international and national debates in these three fields of expertise (and the industry's impact on these debates) is of vital importance. This paper presents the World Nuclear Association (WNA) approach to building and enhancing worldwide industry cooperation in radiological protection, waste management and decommissioning, which is manifested through the activities of the two WNA working groups on radiological protection (RPWG) and on waste management and decommissioning (WM and DWG). This paper also briefly describes the WNA's participatory role, as of Summer 2005, in the International Atomic Energy Agency (IAEA) standard development committees on radiation safety (RASSC), waste safety (WASSC) and nuclear safety (NUSSC). This participation provides the worldwide nuclear industry with an opportunity to be part of IAEA's discussions on shaping changes to the control regime of IAEA safety standards. The review (and the prospect of a revision) of IAEA safety standards, which began in October 2005, makes this WNA participation and the industry's involvement at the national level timely and important. All of this excellent industry cooperation and team effort is done through 'collegial' exchanges between key industry experts, which help tackle important issues more effectively. The WNA is continuously looking to enhance its worldwide industry representation in these fields of expertise through the RPWG and WM and DWG

Cleanroom energy benchmarking in high-tech and biotech industries

International Nuclear Information System (INIS)

Tschudi, William; Benschine, Kathleen; Fok, Stephen; Rumsey, Peter

2001-01-01

Cleanrooms, critical to a wide range of industries, universities, and government facilities, are extremely energy intensive. Consequently, energy represents a significant operating cost for these facilities. Improving energy efficiency in cleanrooms will yield dramatic productivity improvement. But more importantly to the industries which rely on cleanrooms, base load reduction will also improve reliability. The number of cleanrooms in the US is growing and the cleanroom environmental systems' energy use is increasing due to increases in total square footage and trends toward more energy intensive, higher cleanliness applications. In California, many industries important to the State's economy utilize cleanrooms. In California these industries utilize over 150 cleanrooms with a total of 4.2 million sq. ft. (McIlvaine). Energy intensive high tech buildings offer an attractive incentive for large base load energy reduction. Opportunities for energy efficiency improvement exist in virtually all operating cleanrooms as well as in new designs. To understand the opportunities and their potential impact, Pacific Gas and Electric Company sponsored a project to benchmark energy use in cleanrooms in the electronics (high-tech) and biotechnology industries. Both of these industries are heavily dependent intensive cleanroom environments for research and manufacturing. In California these two industries account for approximately 3.6 million sq. ft. of cleanroom (McIlvaine, 1996) and 4349 GWh/yr. (Sartor et al. 1999). Little comparative energy information on cleanroom environmental systems was previously available. Benchmarking energy use allows direct comparisons leading to identification of best practices, efficiency innovations, and highlighting previously masked design or operational problems

Multivariate Analyses of Heavy Metals in Surface Soil Around an Organized Industrial Area in Eskisehir, Turkey.

Science.gov (United States)

Malkoc, S; Yazici, B

2017-02-01

A total of 50 surface industrial area soil in Eskisehir, Turkey were collected and the concentrations of As, Cr, Cd, Co, Cu, Ni, Pb, Zn, Fe and Mg, at 11.34, 95.8, 1.37, 15.28, 33.06, 143.65, 14.34, 78.79 mg/kg, 188.80% and 78.70%, respectively. The EF values for As, Cu, Pb and Zn at a number of sampling sites were found to be the highest among metals. Igeo-index results show that the study area is moderately polluted with respect to As, Cd, Ni. According to guideline values of Turkey Environmental Quality Standard for Soils, there is no problem for Pb, but the Cd values are fairly high. However, Cr, Cu, Ni and Zn values mostly exceed the limits. Cluster analyses suggested that soil the contaminator values are homogenous in those sub classes. The prevention and remediation of the heavy metal soil pollution should focus on these high-risk areas in the future.

HRD System and Experience in the Korean Nuclear Industry

Energy Technology Data Exchange (ETDEWEB)

Kang, Byoungkook [KHNP Nuclear Power Education Institute, Busan (Korea, Republic of)

2012-03-15

Korea began to nurture its nuclear energy pioneers in the 1950s when the government dispatched personnel in research and policy-making areas to foreign institutions. Then in 1959, KAERI was established and now plays a leading role in nuclear technology R and D. In addition, Korea's first research reactor, TRIGA Mark-II, was built and put into operation in 1962. This paved the way for advancements in operation and technical development of nuclear reactors. In turn, these accomplishments led to the birth of Korea's first commercial reactor, Kori Unit 1, in the 1970s, and HRD in the nuclear industry was put on the right track. However, the Korean nuclear industry remained heavily dependent on nuclear exporting countries such as the US, Canada, and France. Already confident in construction, Korea took the lead in building Kori Units 3 and 4 and Ulchin Units 1 and 2 in the 1980s, but the country was still in need of technological self-reliance. In order to achieve this, Korea proactively launched systematic HRD programs and dispatched nuclear professionals to overseas nuclear facilities to secure individuals competent in the areas of NPP operations, plant design, and major equipment manufacturing. Thanks to its diligent endeavors, Korea's nuclear entities established independent nuclear training institutes in the 1990s and began producing a large number of competent personnel. This allowed the country to ensure not only the best operation and maintenance engineers but also the essential nuclear technology required for plant design and equipment manufacturing. Since the beginning of the 21{sup st} century, Korea has been producing its nuclear personnel on its own and exchanging nuclear training instructors and trainees with other organizations in fields where specialized knowledge is needed. Furthermore, Korea is taking comprehensive nuclear HRD measures in response to the rising demand for human resources that result from ongoing construction of NPPs in

HRD System and Experience in the Korean Nuclear Industry

International Nuclear Information System (INIS)

Kang, Byoungkook

2012-01-01

Korea began to nurture its nuclear energy pioneers in the 1950s when the government dispatched personnel in research and policy-making areas to foreign institutions. Then in 1959, KAERI was established and now plays a leading role in nuclear technology R and D. In addition, Korea's first research reactor, TRIGA Mark-II, was built and put into operation in 1962. This paved the way for advancements in operation and technical development of nuclear reactors. In turn, these accomplishments led to the birth of Korea's first commercial reactor, Kori Unit 1, in the 1970s, and HRD in the nuclear industry was put on the right track. However, the Korean nuclear industry remained heavily dependent on nuclear exporting countries such as the US, Canada, and France. Already confident in construction, Korea took the lead in building Kori Units 3 and 4 and Ulchin Units 1 and 2 in the 1980s, but the country was still in need of technological self-reliance. In order to achieve this, Korea proactively launched systematic HRD programs and dispatched nuclear professionals to overseas nuclear facilities to secure individuals competent in the areas of NPP operations, plant design, and major equipment manufacturing. Thanks to its diligent endeavors, Korea's nuclear entities established independent nuclear training institutes in the 1990s and began producing a large number of competent personnel. This allowed the country to ensure not only the best operation and maintenance engineers but also the essential nuclear technology required for plant design and equipment manufacturing. Since the beginning of the 21 st century, Korea has been producing its nuclear personnel on its own and exchanging nuclear training instructors and trainees with other organizations in fields where specialized knowledge is needed. Furthermore, Korea is taking comprehensive nuclear HRD measures in response to the rising demand for human resources that result from ongoing construction of NPPs in Korea and the UAE

In situ observation of triple junction motion during recovery of heavily deformed aluminum

DEFF Research Database (Denmark)

Yu, Tianbo; Hughes, Darcy A.; Hansen, Niels

2015-01-01

-junctions are pinned by deformation-induced interconnecting and lamellar boundaries, which slow down the recovery process and lead to a stop-go migration pattern. This pinning mechanism stabilizes the deformation microstructure, i.e. the structure is stabilized by balancing the driving and pinning forces controlling......Microstructural evolution during in situ annealing of heavily cold-rolled aluminum has been studied by transmission electron microscopy, confirming that an important recovery mechanism is migration of triple junctions formed by three lamellar boundaries (Y-junctions). The migrating Y...

Nice Guys Finish Last: Are People with Higher Tax Morale Taxed more Heavily?

OpenAIRE

Philipp Doerrenberg; Denvil Duncan; Clemens Fuest; Andreas Peichl

2012-01-01

This paper is the first to provide evidence of efficient taxation of groups with heterogeneous levels of 'tax morale'. We set up an optimal income tax model where high tax morale implies a high subjective cost of evading taxes. The model predicts that 'nice guys finish last': groups with higher tax morale will be taxed more heavily, simply because taxing them is less costly. Based on unique cross-country micro data and an IV approach to rule out reverse causality, we find empirical support fo...

Part of the inter ministerial commission of artificial radioelements (cirea) in the areas of medicine, research and industry

International Nuclear Information System (INIS)

Fages, D.Ph.

2000-01-01

The Inter ministerial commission of artificial radioelements (C.I.R.E.A.) has been implemented to regulate the production, import, use of artificial radioelements. It gives advices in areas such preparation, import, export, fabrication, calibration, transport, transfer as well as the general conditions of use, the measures of protection against the effects of radiations. The commission is divided in two sections: for the first one, it treats the questions relative to medical practices and human biology, for the second one it treats questions relative to others areas( agriculture, industry, research else than medical one). (N.C.)

Eco-geochemical peculiarities of mercury content in solid residue of snow in the industrial enterprises impacted areas of Tomsk

Science.gov (United States)

Filimonenko, E. A.; Lyapina, E. E.; Talovskaya, A. V.; Parygina, I. A.

2014-11-01

Snow, as short-term consignation Wednesday, has several properties that lead to its widespread use in ecologicalgeochemical and geological research. By studying the chemical composition of the dust fallout you can indirectly assess the condition of atmospheric air.1-2. Determining the content of mercury in snow cover, you can define its contribution for the longest period of the year in our region, with the most intensive use of various types of fuel (coal, gas, firewood), that puts a strain on urban ecosystems in terms of ecology.3-4. In addition, snow cleans the atmosphere of mercury, but it accumulates in the snow, and during the spring melting of snow hits the ground and rivers, polluting them. Part of the mercury back into the atmosphere. It should also be note the special nature of the circulation of air masses over the city in winter, creating a heat CAP, which contributes to air pollution of the city. 5-6-7. The high load areas of industrial impact were detected during the eco-geochemical investigations of mercury load index in the impacted areas of enterprises of Tomsk. It was found out, that aerosol particles of industrial emissions in Tomsk contain mercury. The contamination transfer character of mercury sources and occurrence modes of pollutants in snow solid residue were detected during the researches of industrial impact.

Estimation of free carrier concentrations in high-quality heavily doped GaN:Si micro-rods by photoluminescence and Raman spectroscopy

Science.gov (United States)

Mohajerani, M. S.; Khachadorian, S.; Nenstiel, C.; Schimpke, T.; Avramescu, A.; Strassburg, M.; Hoffmann, A.; Waag, A.

2016-03-01

The controlled growth of highly n-doped GaN micro rods is one of the major challenges in the fabrication of recently developed three-dimensional (3D) core-shell light emitting diodes (LEDs). In such structures with a large active area, higher electrical conductivity is needed to achieve higher current density. In this contribution, we introduce high quality heavily-doped GaN:Si micro-rods which are key elements of the newly developed 3D core-shell LEDs. These structures were grown by metal-organic vapor phase epitaxy (MOVPE) using selective area growth (SAG). We employed spatially resolved micro-Raman and micro-photoluminescence (PL) in order to directly determine a free-carrier concentration profile in individual GaN micro-rods. By Raman spectroscopy, we analyze the low-frequency branch of the longitudinal optical (LO)-phonon-plasmon coupled modes and estimate free carrier concentrations from ≍ 2.4 × 1019 cm-3 up to ≍ 1.5 × 1020 cm-3. Furthermore, free carrier concentrations are determined by estimating Fermi energy level from the near band edge emission measured by low-temperature PL. The results from both methods reveal a good consistency.

Water requirements of selected industries

Science.gov (United States)

,; Mussey, Orville D.; Conklin, Howard L.; Durfor, Charles N.; Otts, Louis Ethelbert; Walling, Faulkner B.

1955-01-01

The early industries in America generally were established when and where demands for the products of industry arose. Most of the early industries were so located that their increasing requirements for transportation, raw materials, market, labor, and water supply could be satisfied economically. Many of these original plant locations have continued as modern industrial centers and their output has increased manyfold in meeting the demands of our growing Nation. The recent and current industrial expansion and the trend toward the growth of chemical industries, many Of which are heavy users of water, has resulted in a tremendous increase in the total withdrawal of water for industrial use as well as a large increase in the per capita use of water. This increase in industrial water requirement has strained the capacity of the developed water supplies in many areas, and in some instances the adequacy of the potential water supplies is questionable. The Geological Survey is engaged in preparing and publishing a series of reports describing the developed and undeveloped water resources of many important industrial areas. This work was started initially at the request of the National Securities Resources Board as a means to insure that water supplies are adequate for our rapidly expanding industrial development. Although many factors contribute to establishing the feasibility or even the limits of future industrial development, the one relating to available water supply is extremely important. A knowledge of the water requirements of various industries is valuable therefore in planning the logical development in any area where water supply is a critical factor. Thus far very little suitable information on the water requirements of our major industries is available for general planning. An inventory of unit water-use values in industry therefore would be generally helpful and also might tend to stimulate water-conservation methods. To obtain such information

Environmental compliance in the petrochemical industry in the Sarnia area

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-04-01

In February 2004, the Ontario Ministry of the Environment directed its Environmental SWAT Team to conduct a comprehensive inspection sweep of Sarnia's industrial sector to ensure that all facilities in that region were brought into compliance with environmental legislation. The primary focus was to inspect areas with the potential for future spills or unlawful discharges that could pose risks to human health or the environment. Legislative and regulatory gaps that could allow environmentally unsafe practices to exist at the facilities were also revealed. The inspection sweep involved comprehensive inspections of 35 petrochemical plant's air emissions, water discharges and spill prevention plans. SWAT officers examined waste management, laboratory operations and other areas that must meet environmental legislative requirements. Nearly all of the of facilities inspected during the sweep were found to be in non-compliance with one or more legislative or regulatory requirement. Common deficiencies included: no spill contingency or spill prevention plans; not having a Certificate of Approval for wastewater collection and treatment works or air emission control equipment; altering equipment, systems, processes, or structure contrary to the existing Certificate of Approval; and improper chemical handling, storage and identification. As a result of the inspection, 6 facilities were ordered to develop both a spill prevention plan and a spill contingency plan and 2 facilities were ordered to develop a spill prevention plan. SWAT officers have followed up to ensure that companies have taken appropriate corrective actions. The inspection revealed some of the sound practices undertaken at some facilities, such as containment; monitoring; prevention of discharge of contaminants to air or water; waste water and storm water treatment; contingency planning; and process hazard analysis of all key processes. refs., tabs., figs.

Atmospheric dispersion of pollutants in an industrial area of Cuba

International Nuclear Information System (INIS)

Cruz Monte de Oca, Feliberto de la; Furet Bridon, Norma Raisa; Turtos Carbonell, Leonor; Lorente Vera, Mercedes

2011-01-01

Air pollution by different chemicals; take a great connotation in the world, given the adverse effects on ecosystems and particularly human health. The urban development, the modification of the land surface and the climate change, phenomena derived from a world population explosion, are altering the composition of the air. The atmosphere deposits pollutants in the water courses and in land, which harms not only the persons, but also to the animals and the plants of the ecosystem. To know as these pollutants are dispersed in the atmosphere it is very important in the establishment of better urban, regional and world predictions of the air quality. The present study aims to assess the local spread of sulphur dioxide, nitrogen oxides and particulate matter from an industrial zone. The study was done using the pollutant Gaussian Dispersion Models AERMOD. For the evaluation of contaminants were considered two modeling scenarios: urban and rural. The SO 2 concentrations (μg/m 3 ) were obtained for 1 h, 24 h and all period (1 year), exceeding the permissible limits (500, 50 y 20 μg/m 3 ). It was also recorded for each period the number of times SO 2 concentrations exceeded the reference values in each of the scenarios discussed (urban: 39, 61 y 39; rural: 99, 75 y 25). At the end of modeling in the urban setting, 39 recipients exceeded the reference value, occupying an area of 9.75 km 2 and 25 receivers in the case of the rural setting, for an area of 6.25 km 2 . For NOx and particulate matter concentrations estimated values were always below the reference values. The obtained results in this case show the potentiality of AERMOD system for the evaluation of atmospheric dispersion of pollutants

“…then came Cisco, and the rest is history”: a ‘history friendly’ model of the Local Area Networking industry

OpenAIRE

R. Fontana; L. Zirulia

2015-01-01

We study the role that switching costs, compatibility, and mergers and acquisitions, play in influencing the evolution of a multi-market industry. By looking at the case of the Local Area Networking industry, we propose a 'history friendly model' to replicate its evolution during the 1990s. Our model explains how a firm can start from a dominant position in one of the existing markets and exploit switching costs and compatibility to enter a new market when it opens. Mergers and acquisitions a...

Industrial waste heat for district heating

International Nuclear Information System (INIS)

Heitner, K.L.; Brooks, P.P.

1982-01-01

Presents 2 bounding evaluations of industrial waste heat availability. Surveys waste heat from 29 major industry groups at the 2-digit level in Standard Industrial Codes (SIC). Explains that waste heat availability in each industry was related to regional product sales, in order to estimate regional waste heat availability. Evaluates 4 selected industries at the 4-digit SIC level. Finds that industrial waste heat represents a significant energy resource in several urban areas, including Chicago and Los Angeles, where it could supply all of these areas residential heating and cooling load. Points out that there is a strong need to evaluate the available waste heat for more industries at the 4-digit level. Urges further studies to identify other useful industrial waste heat sources as well as potential waste heat users

The potential for ore, industrial minerals and commercial stones in the Simpevarp area

International Nuclear Information System (INIS)

Lindroos, Hardy

2004-10-01

On behalf of SKB (the Swedish Nuclear Fuel and Waste Management Company), a survey has been made of existing information concerning the potential for ore, industrial minerals and commercial stones in and around the two candidate areas for a deep repository in Oskarshamn. A deep repository for spent nuclear fuel should not be located in a rock type or in an area where mineral extraction might be considered in the future, since this would make it difficult or impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities.The survey has made use of the geoscientific information compiled in the more regional investigations in Oskarshamn Municipality in 1998-99. The new information after the municipal study includes extensive geophysical measurements from both the air and the ground. The results of the recently completed geophysical helicopter survey of the Simpevarp area are presented in a special chapter. The judgement of an area's ore potential is in part based on the evaluation of these geophysical measurements. In order to be better able to judge the ore potential, a geochemical investigation of soil samples, including reanalysing of older samples collected by the Geological Survey of Sweden (SGU), has been carried out. The report also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. In cooperation with SGU a mineral resource map of the Simpevarp area has been prepared. The map shows two areas with a potential for commercial stones, namely the granites at Goetemar and Uthammar, situated in the northernmost respectively the southernmost part of the study area. Furthermore, the Goetemar granite has probably a small potential for ores containing tin (Sn) and/or wolfram (W). Although no mineralizations of this type have so far been found, the Goetemar granite area may be unsuitable or for

The potential for ore, industrial minerals and commercial stones in the Simpevarp area

Energy Technology Data Exchange (ETDEWEB)

Lindroos, Hardy [MIRAB Mineral Resurser AB, Uppsla (Sweden)

2004-10-01

On behalf of SKB (the Swedish Nuclear Fuel and Waste Management Company), a survey has been made of existing information concerning the potential for ore, industrial minerals and commercial stones in and around the two candidate areas for a deep repository in Oskarshamn. A deep repository for spent nuclear fuel should not be located in a rock type or in an area where mineral extraction might be considered in the future, since this would make it difficult or impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities.The survey has made use of the geoscientific information compiled in the more regional investigations in Oskarshamn Municipality in 1998-99. The new information after the municipal study includes extensive geophysical measurements from both the air and the ground. The results of the recently completed geophysical helicopter survey of the Simpevarp area are presented in a special chapter. The judgement of an area's ore potential is in part based on the evaluation of these geophysical measurements. In order to be better able to judge the ore potential, a geochemical investigation of soil samples, including reanalysing of older samples collected by the Geological Survey of Sweden (SGU), has been carried out. The report also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. In cooperation with SGU a mineral resource map of the Simpevarp area has been prepared. The map shows two areas with a potential for commercial stones, namely the granites at Goetemar and Uthammar, situated in the northernmost respectively the southernmost part of the study area. Furthermore, the Goetemar granite has probably a small potential for ores containing tin (Sn) and/or wolfram (W). Although no mineralizations of this type have so far been found, the Goetemar granite area may be unsuitable or

CSR in Industrial Clusters

DEFF Research Database (Denmark)

Lund-Thomsen, Peter; Pillay, Renginee G.

2012-01-01

Purpose – The paper seeks to review the literature on CSR in industrial clusters in developing countries, identifying the main strengths, weaknesses, and gaps in this literature, pointing to future research directions and policy implications in the area of CSR and industrial cluster development....... Design/methodology/approach – A literature review is conducted of both academic and policy-oriented writings that contain the keywords “industrial clusters” and “developing countries” in combination with one or more of the following terms: corporate social responsibility, environmental management, labor...... standards, child labor, climate change, social upgrading, and environmental upgrading. The authors examine the key themes in this literature, identify the main gaps, and point to areas where future work in this area could usefully be undertaken. Feedback has been sought from some of the leading authors...

Environmental damage costs from airborne pollution of industrial activities in the greater Athens, Greece area and the resulting benefits from the introduction of BAT

International Nuclear Information System (INIS)

Mirasgedis, S.; Hontou, V.; Georgopoulou, E.; Sarafidis, Y.; Gakis, N.; Lalas, D.P.; Loukatos, A.; Gargoulas, N.; Mentzis, A.; Economidis, D.; Triantafilopoulos, T.; Korizi, K.; Mavrotas, G.

2008-01-01

Attributing costs to the environmental impacts associated with industrial activities can greatly assist in protecting human health and the natural environment as monetary values are capable of directly influencing technological and policy decisions without changing the rules of the market. This paper attempts to estimate the external cost attributable to the atmospheric pollution from 'medium and high environmental burden' industrial activities located in the greater Athens area and the benefits from Best Available Techniques (BAT) introduction. To this end a number of typical installations were defined to be used in conjunction with the Impact Pathway Approach developed in the context of the ExternE project to model all industrial sectors/sub-sectors located in the area of interest. Total environmental externalities due to air pollutants emitted by these industrial activities were found to reach 211 M Euro per year, associated mainly with human mortality and morbidity due to PM 10 emissions, as well as with climate change impacts due to CO 2 emissions for which non-metallic minerals and oil processing industries are the main sources. The results obtained can be used as the basis for an integrated evaluation of potential BAT, taking into account not only private costs and benefits but also the environmental externalities, thus leading to policy decisions that maximize social welfare in each industrial sector/sub-sector

Using stable isotopes in tracing contaminant sources in an industrial area: A case study on the hydrological basin of the Olt River, Romania

Energy Technology Data Exchange (ETDEWEB)

Popescu, Raluca [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICSI Ramnicu Valcea, 4 Uzinei Str, RO-240050 Ramnicu-Valcea (Romania); Mimmo, Tanja [Faculty of Science and Technology, Free University of Bozen-Bolzano, University Plaza no. 5, I-39100 Bolzano (Italy); Dinca, Oana Romina [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICSI Ramnicu Valcea, 4 Uzinei Str, RO-240050 Ramnicu-Valcea (Romania); Capici, Calogero [Faculty of Science and Technology, Free University of Bozen-Bolzano, University Plaza no. 5, I-39100 Bolzano (Italy); Costinel, Diana; Sandru, Claudia [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICSI Ramnicu Valcea, 4 Uzinei Str, RO-240050 Ramnicu-Valcea (Romania); Ionete, Roxana Elena, E-mail: roxana.ionete@icsi.ro [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICSI Ramnicu Valcea, 4 Uzinei Str, RO-240050 Ramnicu-Valcea (Romania); Stefanescu, Ioan [National Research and Development Institute for Cryogenics and Isotopic Technologies, ICSI Ramnicu Valcea, 4 Uzinei Str, RO-240050 Ramnicu-Valcea (Romania); Axente, Damian [National Institute for Research and Development of Isotopic and Molecular Technologies, 65–103 Donath Str., RO-400293 Cluj-Napoca (Romania)

2015-11-15

Tracing pollution sources and transformation of nitrogen compounds in surface- and groundwater is an issue of great significance worldwide due to the increased human activity, translated in high demand of water resources and pollution. In this work, the hydrological basin of an important chemical industrial platform in Romania (Ramnicu Valcea industrial area) was characterized in terms of the physico-chemical and isotope composition of δ{sup 18}O and δ{sup 2}H in water samples and δ{sup 15}N of the inorganic nitrogen species. Throughout a period of one year, water samples from the Olt River and its more important tributaries were collected monthly in the industrial area, when the seasonal and spatial isotope patterns of the surface waters and the main sources of pollution were determined. Higher inorganic nitrogen concentrations (up to 10.2 mg N L{sup −1}) were measured between November 2012 and April 2013, which were designated as anthropogenic additions using the mixing calculations. The main sources of pollution with inorganic nitrogen were agriculture and residential release. The inorganic nitrogen from the industrial waste water duct had a distinct δ{sup 15}N fingerprint (mean of − 8.6‰). Also, one industrial release into the environment was identified for Olt River, at Ionesti site, in November 2012. The mean precipitation samples had the lowest inorganic nitrogen concentrations (less than 5.5 mg N L{sup −1}) with a distinct δ{sup 15}N fingerprint compared to the surface and industrial waters. - Highlights: • The main source of nitrogen pollution was agriculture/residential. • Anthropogenic additions of nitrogen were identified in the colder months. • Industrial nitrogen source was differentiated from the agriculture/residential one. • One industrial nitrogen release in the Olt River was observed during the study.

Using stable isotopes in tracing contaminant sources in an industrial area: A case study on the hydrological basin of the Olt River, Romania

International Nuclear Information System (INIS)

Popescu, Raluca; Mimmo, Tanja; Dinca, Oana Romina; Capici, Calogero; Costinel, Diana; Sandru, Claudia; Ionete, Roxana Elena; Stefanescu, Ioan; Axente, Damian

2015-01-01

Tracing pollution sources and transformation of nitrogen compounds in surface- and groundwater is an issue of great significance worldwide due to the increased human activity, translated in high demand of water resources and pollution. In this work, the hydrological basin of an important chemical industrial platform in Romania (Ramnicu Valcea industrial area) was characterized in terms of the physico-chemical and isotope composition of δ 18 O and δ 2 H in water samples and δ 15 N of the inorganic nitrogen species. Throughout a period of one year, water samples from the Olt River and its more important tributaries were collected monthly in the industrial area, when the seasonal and spatial isotope patterns of the surface waters and the main sources of pollution were determined. Higher inorganic nitrogen concentrations (up to 10.2 mg N L −1 ) were measured between November 2012 and April 2013, which were designated as anthropogenic additions using the mixing calculations. The main sources of pollution with inorganic nitrogen were agriculture and residential release. The inorganic nitrogen from the industrial waste water duct had a distinct δ 15 N fingerprint (mean of − 8.6‰). Also, one industrial release into the environment was identified for Olt River, at Ionesti site, in November 2012. The mean precipitation samples had the lowest inorganic nitrogen concentrations (less than 5.5 mg N L −1 ) with a distinct δ 15 N fingerprint compared to the surface and industrial waters. - Highlights: • The main source of nitrogen pollution was agriculture/residential. • Anthropogenic additions of nitrogen were identified in the colder months. • Industrial nitrogen source was differentiated from the agriculture/residential one. • One industrial nitrogen release in the Olt River was observed during the study

Modelling of real area of contact between tool and workpiece in metal forming processes including the influence of subsurface deformation

DEFF Research Database (Denmark)

Nielsen, Chris Valentin; Martins, Paulo A. F.; Bay, Niels Oluf

2016-01-01

New equipment for testing asperity deformation at various normal loads and subsurface elongations is presented. Resulting real contact area ratios increase heavily with increasing subsurface expansion due to lowered yield pressure on the asperities when imposing subsurface normal stress parallel ...... for estimating friction in the numerical modelling of metal forming processes.......New equipment for testing asperity deformation at various normal loads and subsurface elongations is presented. Resulting real contact area ratios increase heavily with increasing subsurface expansion due to lowered yield pressure on the asperities when imposing subsurface normal stress parallel...... to the surface. Finite element modelling supports the presentation and contributes by extrapolation of results to complete the mapping of contact area as function of normal pressure and one-directional subsurface strain parallel to the surface. Improved modelling of the real contact area is the basis...

Arsenic, cadmium, and manganese levels in shellfish from Map Ta Phut, an industrial area in Thailand, and the potential toxic effects on human cells.

Science.gov (United States)

Rangkadilok, Nuchanart; Siripriwon, Pantaree; Nookabkaew, Sumontha; Suriyo, Tawit; Satayavivad, Jutamaad

2015-01-01

Map Ta Phut Industrial Estate is a major industrial area in Thailand for both petrochemical and heavy industries. The release of hazardous wastes and other pollutants from these industries increases the potential for contamination in foods in the surrounding area, especially farmed shellfish. This study determined the arsenic (As), cadmium (Cd), and manganese (Mn) concentrations in the edible flesh of farmed shellfish, including Perna viridis, Meretrix meretrix, and Scapharca inaequivalvis, around the Map Ta Phut area using inductively coupled plasma mass spectrometry. The results showed that shellfish samples contained high levels of total As [1.84-6.42 mg kg(-1) wet weight (ww)]. High Mn concentrations were found in P. viridis and M. meretrix, whereas S. inaequivalis contained the highest Cd. Arsenobetaine (AsB) was found to be the major As species in shellfish (>45% of total As). The in vitro cytotoxicity of these elements was evaluated using human cancer cells (T47D, A549, and Jurkat cells). An observed decrease in cell viability in T47D and Jurkat cells was mainly caused by exposure to inorganic As (iAs) or Mn but not to AsB or Cd. The combined elements (AsB+Mn+Cd) at concentrations predicted to result from the estimated daily intake of shellfish flesh by the local people showed significant cytotoxicity in T47D and Jurkat cells.

Department of Defense Partners in Flight Strategic Plan

Science.gov (United States)

2004-07-28

forests are private industrial timberlands and often are heavily fragmented. Reconciliation of the need for long· term, sustainable timber production...habitats have been set aside as protected areas or incorporated into the existing Parque Nacional Soberania. In addition, the upper Panama Bay...lines present another source of potential mortality, especially for raptors in western states. Several raptor conservation organizations and industry

Seasonal and spatial variations of atmospheric trace elemental deposition in the Aliaga industrial region, Turkey

Science.gov (United States)

Kara, Melik; Dumanoglu, Yetkin; Altiok, Hasan; Elbir, Tolga; Odabasi, Mustafa; Bayram, Abdurrahman

2014-11-01

Atmospheric bulk deposition (wet + dry deposition) samples (n = 40) were collected concurrently at ten sites in four seasons between June 2009 and April 2010 in the Aliaga heavily industrialized region, Turkey, containing a number of significant air pollutant sources. Analyses of trace elements were carried out using inductively coupled plasma-mass spectrometry (ICP-MS). While there were significant differences in the particulate matter (PM) deposition fluxes among the sampling sites, seasonal variations were not statistically significant (Kruskal-Wallis test, p < 0.05). Both PM deposition and elemental fluxes were increased at the sampling sites in the vicinity of industrial activities. The crustal elements (i.e., Ca, Mg) and some anthropogenic elements (such as Fe, Zn, Mn, Pb, Cu, and Cr) were high, and the highest fluxes were mostly measured in summer and winter seasons. The enrichment factor (EF) and principal component analysis (PCA) was applied to the data to determine the possible sources in the study area. High EF values were obtained for the anthropogenic elements such as Ag, Cd, Zn, Pb, Cu and Sb. The possible sources were identified as anthropogenic sources (i.e., iron-steel production) (45.4%), crustal and re-suspended dust (27.1%), marine aerosol (7.9%), and coal and wood combustion (8.2%). Thus, the iron-steel production and its related activities were found to be the main pollutant sources for this region.

Energy use and CO2 emissions of China's industrial sector from a global perspective

International Nuclear Information System (INIS)

Zhou, Sheng; Kyle, G. Page; Yu, Sha; Clarke, Leon E.; Eom, Jiyong; Luckow, Patrick; Chaturvedi, Vaibhav; Zhang, Xiliang; Edmonds, James A.

2013-01-01

The industrial sector has accounted for more than 50% of China's final energy consumption in the past 30 years. Understanding the future emissions and emissions mitigation opportunities depends on proper characterization of the present-day industrial energy use, as well as industrial demand drivers and technological opportunities in the future. Traditionally, however, integrated assessment research has handled the industrial sector of China in a highly aggregate form. In this study, we develop a technologically detailed, service-oriented representation of 11 industrial subsectors in China, and analyze a suite of scenarios of future industrial demand growth. We find that, due to anticipated saturation of China's per-capita demands of basic industrial goods, industrial energy demand and CO 2 emissions approach a plateau between 2030 and 2040, then decrease gradually. Still, without emissions mitigation policies, the industrial sector remains heavily reliant on coal, and therefore emissions-intensive. With carbon prices, we observe some degree of industrial sector electrification, deployment of CCS at large industrial point sources of CO 2 emissions at low carbon prices, an increase in the share of CHP systems at industrial facilities. These technological responses amount to reductions of industrial emissions (including indirect emission from electricity) are of 24% in 2050 and 66% in 2095. - Highlights: • Eleven industrial subsectors in China are detail analyzed from a global perspective. • Industrial energy use and CO 2 emissions will approach a plateau between 2030 and 2040. • Industrial CHP and CCS are truly encouraged by carbon tax. • Some degree of industrial sector electrification are observed by carbon tax

UP-report. Energy intensive industry. Basis of the Development platform. Industry to the Swedish Energy Agency's strategy work FOKUS; UP-rapport. Energiintensiv industri. Underlag fraan Utvecklingsplattformen. Industri till Energimyndighetens strategiarbete FOKUS

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-01

The report serves as input to the Swedish Energy Agency's strategies and priorities for research and innovation under the thematic area of energy intensive industry for the period 2011 - 2016. The report has been compiled by members of the Development platform Industry. This report provides background and conditions for the energy intensive industry, and proposed priorities and activities for future efforts in this area. The development platform has contributed with valuable experience and knowledge which enabled the Swedish Energy Agency to then develop a strategy that meets needs of the society and business.

The nature of the torus in the heavily obscured AGN Markarian 3: an X-ray study

DEFF Research Database (Denmark)

Guainazzi, M.; Risaliti, G.; Awaki, H.

2016-01-01

In this paper, we report the results of an X-ray monitoring campaign on the heavily obscured Seyfert galaxy, Markarian 3, carried out between the fall of 2014 and the spring of 2015 with NuSTAR, Suzaku and XMM–Newton. The hard X-ray spectrum of Markarian 3 is variable on all the time-scales probe...

Perspective sources of industrial minerals for building industry in Novohrad (Southern Slovakia

Directory of Open Access Journals (Sweden)

Beláček Boris

1999-03-01

Full Text Available Novohrad a region of Southern Slovakia has wealthy industrial history, which was built mostly on local natural raw materials. Some deposits are exhausted, but other are ready to be exploited. Among such industrial minerals are raw materials for building industry. There are industrial minerals for fine and rough ceramics, stones for building and pavement, sand and gravel. The perspective areas are listed on Tab. 1 - 6 and are shown on Fig 1 - 3.

Using stable isotopes in tracing contaminant sources in an industrial area: A case study on the hydrological basin of the Olt River, Romania.

Science.gov (United States)

Popescu, Raluca; Mimmo, Tanja; Dinca, Oana Romina; Capici, Calogero; Costinel, Diana; Sandru, Claudia; Ionete, Roxana Elena; Stefanescu, Ioan; Axente, Damian

2015-11-15

Tracing pollution sources and transformation of nitrogen compounds in surface- and groundwater is an issue of great significance worldwide due to the increased human activity, translated in high demand of water resources and pollution. In this work, the hydrological basin of an important chemical industrial platform in Romania (Ramnicu Valcea industrial area) was characterized in terms of the physico-chemical and isotope composition of δ(18)O and δ(2)H in water samples and δ(15)N of the inorganic nitrogen species. Throughout a period of one year, water samples from the Olt River and its more important tributaries were collected monthly in the industrial area, when the seasonal and spatial isotope patterns of the surface waters and the main sources of pollution were determined. Higher inorganic nitrogen concentrations (up to 10.2 mg N L(-1)) were measured between November 2012 and April 2013, which were designated as anthropogenic additions using the mixing calculations. The main sources of pollution with inorganic nitrogen were agriculture and residential release. The inorganic nitrogen from the industrial waste water duct had a distinct δ(15)N fingerprint (mean of -8.6‰). Also, one industrial release into the environment was identified for Olt River, at Ionesti site, in November 2012. The mean precipitation samples had the lowest inorganic nitrogen concentrations (less than 5.5 mg N L(-1)) with a distinct δ(15)N fingerprint compared to the surface and industrial waters. Copyright © 2015 Elsevier B.V. All rights reserved.

Mass balance of emerging contaminants in the water cycle of a highly urbanized and industrialized area of Italy.

Science.gov (United States)

Castiglioni, Sara; Davoli, Enrico; Riva, Francesco; Palmiotto, Marinella; Camporini, Paolo; Manenti, Angela; Zuccato, Ettore

2017-12-22

The occurrence of several classes of emerging contaminants (ECs) was assessed in the River Lambro basin, one of the most urbanized and industrialized areas of Italy. The study aims were to identify the main sources of ECs, quantify their amounts circulating in the water cycle, and study their fate in the aquatic environment. More than 80 ECs were selected among pharmaceuticals (PHARM), personal care products (PCPs), disinfectants (DIS), illicit drugs (IDs), perfluorinated compounds (PERF), alkylphenols and bisphenol A (Alk-BPA), and anthropogenic markers (AM). Specific analytical methods were developed for quantitative analysis based on solid phase extraction and liquid chromatography tandem mass spectrometry. ECs were measured in rivers upstream and downstream of the main city (Milan), and in untreated and treated wastewater from Milan to assess the contribution to river contamination, and in superficial and deep groundwater in the city area to study the relationship between river and groundwater contamination. Samples were collected in a two-year monitoring campaign. Almost all ECs were ubiquitous in untreated wastewater, at concentrations up to the μg/L range, and the most abundant classes were PHARM and AM. Removals during different wastewater treatment processes were studied and the most stable substances were PHARM, PCPs and PERF. The mass loads increased for all the classes of ECs along the River Lambro basin. A mass balance was done in the river basin and allowed to identify the main sources of contamination, which were domestic, from treated or untreated wastewater, for PHARM, PCPs and IDs, mainly industrial for PERF, and both industrial and domestic for Alk-BPA. The study of AM helped to identify direct discharges of untreated wastewater. A substantial contribution of surface water to groundwater contamination was observed. This study improves the knowledge on occurrence, sources and fate of multiple classes of ECs in a highly urbanized area providing

Utilization of hair and nails as bio-indicators of contamination by heavy and toxic metals in industrial workers

International Nuclear Information System (INIS)

Vilhena Schayer Sabino, Claudia de; Silva, Ascanio Barros F.E.; Fernandes, Marcio Prado; Amaral, Angela Maria; Franco, Milton Batista; Guedes, Joao Bosco; Francisco, Dovenir; Castro de Assis, Adilson de.

1996-01-01

Instrumental neutron activation analysis and atomic absorption spectrometry were performed on scalp hair and fingernail samples collected from a group of heavily exposed healthy mail industrial workers. The concentration of trace elements (As, Cd, Cr, Hg, Ni, Pb and Sb) were evaluated and compared for scalp and fingernails. Comparative studies demonstrated that concentration of certain elements were greater than those corresponding to non-exposed workers. (author). 4 refs., 6 tabs

Near-Field Imaging of Free Carriers in ZnO Nanowires with a Scanning Probe Tip Made of Heavily Doped Germanium

Science.gov (United States)

Sakat, Emilie; Giliberti, Valeria; Bollani, Monica; Notargiacomo, Andrea; Pea, Marialilia; Finazzi, Marco; Pellegrini, Giovanni; Hugonin, Jean-Paul; Weber-Bargioni, Alexander; Melli, Mauro; Sassolini, Simone; Cabrini, Stefano; Biagioni, Paolo; Ortolani, Michele; Baldassarre, Leonetta

2017-11-01

A novel scanning probe tip made of heavily doped semiconductor is fabricated and used instead of standard gold-coated tips in infrared scattering-type near-field microscopy. Midinfrared near-field microscopy experiments are conducted on ZnO nanowires with a lateral resolution better than 100 nm, using tips made of heavily electron-doped germanium with a plasma frequency in the midinfrared (plasma wavelength of 9.5 μ m ). Nanowires embedded in a dielectric matrix are imaged at two wavelengths, 11.3 and 8.0 μ m , above and below the plasma wavelength of the tips. An opposite sign of the imaging contrasts between the nanowire and the dielectric matrix is observed at the two infrared wavelengths, indicating a clear role of the free-electron plasma in the heavily doped germanium tip in building the imaging contrast. Electromagnetic simulations with a multispherical dipole model accounting for the finite size of the tip are well consistent with the experiments. By comparison of the simulated and measured imaging contrasts, an estimate for the local free-carrier density in the investigated ZnO nanowires in the low 1019 cm-3 range is retrieved. The results are benchmarked against the scattering intensity and phase maps obtained on the same sample with a gold-coated probe tip in pseudoheterodyne detection mode.

Air pollution in the Benelux/Rhine-Ruhr area: Numerical simulations with a multi-scale regional chemistry-transport model

Science.gov (United States)

Memmesheimer, M.; Jakobs, H. J.; Wurzler, S.; Friese, E.; Piekorz, G.; Ebel, A.

2009-04-01

The Rhine-Ruhr area is a strongly industrialized region with about 10 Million inhabitants. It is one of the regions in Europe, which has the characteristics of a megacity with respect to population density, traffic, industry and environmental issues. The main centre of European steel production and the biggest inland port of the world is located in Duisburg, one of the major cities in the Rhine-Ruhr area. Together with the nearby urban agglomerations in the Benelux area including Brussels, Amsterdam and in particular Rotterdam as one of the most important sea-harbours of the world together with Singapore and Shanghai, it forms one of the regions in Europe heavily loaded with air pollutants as ozone, NO2 and particulate matter. Ammonia emissions outside the urban agglomerations but within the domain are also on a quite high level due to intense agricultural usage in Benelux, North-Rhine-Westphalia and lower Saxony. Therefore this area acts also as an important source region for gaseous precursors contributing to the formation of secondary particles in the atmosphere. The Benelux/Rhine-Ruhr area therefore has been selected within the framework of the recently established FP7 research project CityZen as one hot spot for detailed investigations of the past and current status of air pollution and its future development on different spatial and temporal scales. Some examples from numerical simulations with the regional multi-scale chemistry transport model EURAD for Central Europe and the Rhine-Ruhr area will be presented. The model calculates the transport, chemical transformations and deposition of trace constituents in the troposphere from the surface up to about 16 km using MM5 as meteorological driver, the RACM-MIM gas-phase chemistry and MADE-SORGAM for the treatment of particulate matter. Horizontal grid sizes are in the range of 100 km down to 1 km for heavily polluted urbanized areas within Benelux/Rhine-Ruhr. The planetary boundary layer is resolved by 15

Lidar mapping of atmospheric atomic mercury in the Wanshan area, China.

Science.gov (United States)

Lian, Ming; Shang, Lihai; Duan, Zheng; Li, Yiyun; Zhao, Guangyu; Zhu, Shiming; Qiu, Guangle; Meng, Bo; Sommar, Jonas; Feng, Xinbin; Svanberg, Sune

2018-05-08

A novel mobile laser radar system was used for mapping gaseous atomic mercury (Hg 0 ) atmospheric pollution in the Wanshan district, south of Tongren City, Guizhou Province, China. This area is heavily impacted by legacy mercury from now abandoned mining activities. Differential absorption lidar measurements were supplemented by localized point monitoring using a Lumex RA-915M Zeeman modulation mercury analyzer. Range-resolved concentration measurements in different directions were performed. Concentrations in the lower atmospheric layers often exceeded levels of 100 ng/m 3 for March conditions with temperature ranging from 5 °C to 20 °C. A flux measurement of Hg 0 over a vertical cross section of 0.12 km 2 resulted in about 29 g/h. Vertical lidar sounding at night revealed quickly falling Hg 0 concentrations with height. This is the first lidar mapping demonstration in a heavily mercury-polluted area in China, illustrating the lidar potential in complementing point monitors. Copyright © 2018 Elsevier Ltd. All rights reserved.

Risk perception of aquatic pollution originated from chemical industry clusters in the coastal area of Jiangsu province, China.

Science.gov (United States)

Yao, Hong; Liu, Bo; You, Zhen; Zhao, Li

2018-02-01

According to "the Layout Scheme of the Chemical Industry in Jiangsu Province From 2016 to 2030" and "the Development Planning in the Coastal Area of Jiangsu Province, China," several chemical industry clusters will be located in the coastal area of Jiangsu province, China, and the risk of surface water pollution will be inevitably higher in the densely populated region. To get to know the risk acceptance level of the residents near the clusters, public perception was analyzed from the five risk factors: the basic knowledge about the pollution, the negative effects on aquatic environment imposed by the clusters, the positive effects brought by the clusters, the trust of controlling aquatic pollution, and the acceptance of the clusters. Twenty-four statements were screened out to describe the five factors, and about 600 residents were covered in three typical clusters surveyed. On the whole, the youth showed a higher interest on the survey, and middle-aged people were likely to be more concerned about aquatic pollution incident. There was no significant difference on risk perception of the three clusters. The respondents investigated had good knowledge background on aquatic pollution and the residents identified with the benefits brought by the clusters. They were weak in risk awareness of pollution originated from the chemical enterprises' groups. Although the respondents regarded that chemical industry clusters did not expose all points of pollutants' generation to the public, they inclined to trust the administration agencies on controlling the pollution and welcome the construction of chemical clusters in their dwelling cities. Besides, risk perception showed obvious spatial distribution. The closer were the samples' sites to the clusters and the rivers receiving pollutants, the higher were the residents' perceived risk, benefit, and trust. However, there was no identical spatial difference on risk acceptance, which might be comprehensively influenced by various

Reception and treatment facilities for waste oils and oil-polluted waters from marine and industrial activities in Gothenburg, Sweden

International Nuclear Information System (INIS)

Andersson, K.; Lexen, S.I.; Hell, M.

1992-01-01

At the beginning of the 1980s, comprehensive solutions were found to problems associated with the handling of oil-polluted water from marine and industrial sources in the Gothenburg area. The treatment plant in the oil harbour has permission to treat 700,000 m 3 /yr of sludge, ballast, slops and other oil-contaminated waters. Following treatment by chemical flocculation, flotation and dual-media filtration, the treated water must not contain more than 5 ppm of oil. Work to improve treatment results has been carried out from the start, in close co-operation with environmental authorities and with the waste generators themselves. Through increased consciousness, improvements in control, and greater source separation, it will be possible to bring about a significantly lower concentration of pollutants in the incoming waste streams. Recent plans include separate treatment of waste streams containing aromatic compounds and heavily polluted waters. Complementary treatment methods, such as activated carbon and air stripping, are under evaluation. (author). 10 figs

Atmospheric carbon tetrachloride in rural background and industry surrounded urban areas in Northern Iberian Peninsula: Mixing ratios, trends, and potential sources

International Nuclear Information System (INIS)

Blas, Maite de; Uria-Tellaetxe, Iratxe; Gomez, Maria Carmen; Navazo, Marino; Alonso, Lucio; García, Jose Antonio; Durana, Nieves; Iza, Jon; Ramón, Jarol Derley

2016-01-01

Latest investigations on atmospheric carbon tetrachloride (CTC) are focused on its ozone depleting potential, adverse effects on the human health, and radiative efficiency and Global Warming Potential as a greenhouse gas. CTC mixing ratios have been thoroughly studied since its restriction under the Montreal Protocol, mostly in remote areas with the aim of reporting long-term trends after its banning. The observed decrease of the CTC background mixing ratio, however, was not as strong as expected. In order to explain this behavior CTC lifetime should be adjusted by estimating the relative significance of its sinks and by identifying ongoing potential sources. Looking for possible sources, CTC was measured with high-time resolution in two sites in Northern Spain, using auto-GC systems and specifically developed acquisition and processing methodologies. The first site, Bilbao, is an urban area influenced by the surrounding industry, where measurements were performed with GC–MSD for a one-year period (2007–2008). The second site, at Valderejo Natural Park (VNP), is a rural background area where measurements were carried out with GC-FID and covering CTC data a nonsuccessive five-year period (2003–2005, 2010–2011, and 2014–2015 years). Median yearly CTC mixing ratios were slightly higher in the urban area (120 pptv) than in VNP (80–100 pptv). CTC was reported to be well mixed in the atmosphere and no sources were noticed to impact the rural site. The observed long-term trend in VNP was in agreement with the estimated global CTC emissions. In the urban site, apart from industrial and commercial CTC sources, chlorine-bleach products used as cleaning agents were reported as promotors of indoor sources. - Highlights: • A methodology was developed to measure CTC using GC-MSD and GC-FID. • CTC ongoing sources were noticed in an industry surrounded urban area. • No noticeable nearby CTC sources impacted the rural site. • Long-term CTC trend in agreement

Atmospheric carbon tetrachloride in rural background and industry surrounded urban areas in Northern Iberian Peninsula: Mixing ratios, trends, and potential sources

Energy Technology Data Exchange (ETDEWEB)

Blas, Maite de, E-mail: maite.deblas@ehu.eus [School of Engineering of Bilbao, University of the Basque Country UPV/EHU (Spain); Uria-Tellaetxe, Iratxe; Gomez, Maria Carmen [School of Engineering of Bilbao, University of the Basque Country UPV/EHU (Spain); Navazo, Marino [University College of Engineering of Vitoria-Gasteiz, University of the Basque Country UPV/EHU (Spain); Alonso, Lucio; García, Jose Antonio; Durana, Nieves; Iza, Jon; Ramón, Jarol Derley [School of Engineering of Bilbao, University of the Basque Country UPV/EHU (Spain)

2016-08-15

Latest investigations on atmospheric carbon tetrachloride (CTC) are focused on its ozone depleting potential, adverse effects on the human health, and radiative efficiency and Global Warming Potential as a greenhouse gas. CTC mixing ratios have been thoroughly studied since its restriction under the Montreal Protocol, mostly in remote areas with the aim of reporting long-term trends after its banning. The observed decrease of the CTC background mixing ratio, however, was not as strong as expected. In order to explain this behavior CTC lifetime should be adjusted by estimating the relative significance of its sinks and by identifying ongoing potential sources. Looking for possible sources, CTC was measured with high-time resolution in two sites in Northern Spain, using auto-GC systems and specifically developed acquisition and processing methodologies. The first site, Bilbao, is an urban area influenced by the surrounding industry, where measurements were performed with GC–MSD for a one-year period (2007–2008). The second site, at Valderejo Natural Park (VNP), is a rural background area where measurements were carried out with GC-FID and covering CTC data a nonsuccessive five-year period (2003–2005, 2010–2011, and 2014–2015 years). Median yearly CTC mixing ratios were slightly higher in the urban area (120 pptv) than in VNP (80–100 pptv). CTC was reported to be well mixed in the atmosphere and no sources were noticed to impact the rural site. The observed long-term trend in VNP was in agreement with the estimated global CTC emissions. In the urban site, apart from industrial and commercial CTC sources, chlorine-bleach products used as cleaning agents were reported as promotors of indoor sources. - Highlights: • A methodology was developed to measure CTC using GC-MSD and GC-FID. • CTC ongoing sources were noticed in an industry surrounded urban area. • No noticeable nearby CTC sources impacted the rural site. • Long-term CTC trend in agreement

The role of urban forest to reduce rain acid in urban industrial areas

Science.gov (United States)

Slamet, B.; Agustiarni, Y.; Hidayati; Basyuni, M.

2018-03-01

Urban forest has many functions mainly on improving the quality of the urban environment. One of the functions is to increase pH and reduce dangerous chemical content. The aim of the research is to find out the role of vegetation density of urban forest around the industrial area in reducing the acid rain. The condition of land cover was classified into four classes which are dense, medium, sparse and open area. The water of the throughfall and stemflow was taken from each type of land cover except in the open area. Parameters measured in this study are water acidity (pH), anion content (SO4 2- and NO3 -), cation content (Ca2+, Mg2+, and NH4 +) and electrical conductivity (EC). The results indicated that urban forest vegetation was able to increase the pH of rain water from 5.42 which is in an open area without vegetation to be 7.13 and 7.32 in dense and moderate vegetation cover by throughfall mechanism, respectively. Rain water acidity also decreased through stemflow mechanism with a pH ranged from 5.92 - 6.43. Urban forest vegetation decreased sulfate content (SO42-) from 528.67 mg/l in open area to 44 - 118 mg/l by throughfall mechanism and ranged from 90 to 366.67 mg/l through stemflow mechanism. Urban forest vegetation significantly decreased the rainwater nitrate content from 27 mg/l to 0.03 - 0.70 mg/l through the mechanism of throughfall and between 1.53 - 8.82 mg/l through the stemflow mechanism. Urban forest vegetation also increased the concentration of cations (NH4+, Ca2+, Mg2+, Na+) compared with open areas. Urban forest vegetation showed increased the electrical conductivity (EC) from 208.12 μmhos/cm to 344.67 - 902.17 μmhos/cm through the through fall mechanism and 937.67 - 1058.70 μmhos/cm through the stemflow mechanism. The study suggested that urban forests play a significant role in reducing rainwater acidity and improving the quality of rainwater that reached the soil surface.

Insurance industry guide

International Nuclear Information System (INIS)

Anon.

1992-01-01

This is an insurance industry guide for the independent power industry. The directory includes the insurance company's name, address, telephone and FAX numbers and a description of the company's area of expertise, products and services, and limitations. The directory is international in scope. Some of the companies specialize in independent power projects

Risk management for industrial safety

International Nuclear Information System (INIS)

Novogno, A.

1989-01-01

The catastrophic accidents which have occurred in the last decade, in both developed and developing countries, have drawn the attention of decision-makers in the safety area to the urgent necessity to assess and manage risks from hazardous industrial activities which are concentrated in large industrialized areas. The aim of this paper is to review experience gained in conducting studies in the area of 'comparisons of risks in energy systems' and on the practical application of 'cost effectiveness of risk reduction analysis among different energy systems' (case studies). It is also the aim of the paper to discuss and propose a general framework for defining an 'integrated approach' to risk assessment and management in highly industrialized regions within a country. (author)

Measurement of surface recombination velocity on heavily doped indium phosphide

International Nuclear Information System (INIS)

Jenkins, P.; Ghalla-Goradia, M.; Faur, M.; Bailey, S.

1990-01-01

The controversy surrounding the published low values of surface recombination velocity (SRV) in n-InP, solidified in recent years when modeling of existing n/p InP solar cells revealed that the front surface SRV had to be higher than 1 x 10 6 cm/sec in order to justify the poor blue response that is characteristic of all n/p InP solar cells. In this paper, SRV on heavily doped (>10 18 cm -3 )n-type and p-type InP is measured as a function of surface treatment. For the limited range of substrates and surface treatments studied, SRV and surface stability depend strongly on the surface treatment. SRVs of ∼10 5 cm/sec in both p-type and n-type InP are obtainable, but in n-type the low SRV surfaces were unstable, and the only stable surfaces on n-type had SRVs of >10 6 cm/sec

Heavily-doped 2D-quantized structures and the Einstein relation

CERN Document Server

Ghatak, Kamakhya P

2015-01-01

This book presents the Einstein Relation(ER) in two-dimensional (2-D) Heavily Doped(HD) Quantized Structures. The materials considered are quantized structures of HD non-linear optical, III-V, II-VI, Ge, Te, Platinum Antimonide, stressed materials, GaP, Gallium Antimonide, II-V, Bismuth Telluride together with various types of HD superlattices and their Quantized counterparts respectively. The ER in HD opto-electronic materials and their nanostructures is studied in the presence of strong light waves and intense electric fields on the basis of newly formulated electron dispersion laws that control the studies of such quantum effect devices. The suggestion for the experimental determination of HD 2D and 3D ERs and the importance of measurement of band gap in HD optoelectronic materials under intense built-in electric field in nanodevices and strong external photo excitation (for measuring photon induced physical properties) are also discussed in this context. The influence of crossed electric and quantizing ma...

Utilization of IT in Pakistan and MNC Pharma. Companies in the Korangi Industrial Area

Directory of Open Access Journals (Sweden)

Raza Kamal

2006-01-01

Full Text Available This research explores the extent of usage of Informational Technology within the pharmaceutical firms based at Korangi Industrial Area. The findings substantiate the view that merely adding computing power will not add to productivity unless theemployees are well trained and the usage is dispersed in all the business processes simultaneously. The design of the research is based on instruments which have a high validity and the results show that there is no significant difference in the level of competence of employees between the Pakistani and the MNC. This may be so since the employees are from the same labour market where they have similar educational background and the firms (both national and multinational have not adequately invested in up grading their IT capabilities..

Identification, Quantification, and Toxicity of PCDDs and PCDFs in Soils from Industrial Areas in the Central and Eastern Regions of Saudi Arabia.

Science.gov (United States)

Al-Wabel, Mohammad I; El-Saeid, Mohamed H; Usman, Adel R A; Al-Turki, Ali M; Ahmad, Mahtab; Hassanin, Ashraf S; El-Naggar, Ahmed H; Alenazi, Khaled K H

2016-05-01

This study was conducted to identify and quantify polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in soil samples collected from selected industrial areas in the central and eastern regions of Saudi Arabia. All the investigated compounds of PCDDs/PCDFs were identified in the studied locations. The average concentrations of PCDDs (sum of seven congeners measured) ranged from 11.5 to 59.6 pg g(-1), with a maximum concentration of 125.7 pg g(-1) at an oil refinery station followed by 100.9 pg g(-1) at a cement factory. The average concentrations of PCDFs (sum of 10 congeners measured) accounted for 11.68-19.35 pg g(-1), with a maximum concentration of 38.67 pg g(-1) at the cement factory. It was generally observed that the soil samples collected from industrial areas have substantially high toxicity equivalence (TEQ) values of PCDDs/PCDFs compared to soils of remote areas. Principal component analysis revealed that the cement factories and oil refineries were the primary sources of PCDDs and PCDFs.

Energy crisis and changes in the structure of the chemical industry

Energy Technology Data Exchange (ETDEWEB)

Dedov, A G

1980-01-01

The effect of the energy crisis together with higher prices and inflation on the chemical industry is reviewed. One effect has been the search for more energy-efficient processes and more widely available raw materials. Measures taken by the industry have included the control of expenses and losses, utilization of secondary materials and energy resources and the development of new technological growth of the industry and has shifted emphasis to small-scale rather than large-scale chemical production. Capital has also been used more for modernizing existing equipment and facilities than for new construction, and industrialized countries have invested more heavily in developing countries. Trade relations between socialist and western countries have also improved. Improvements have been made in the production of aromatic hydrocarbons by extraction with the use of more efficient solvents, in catalytic and thermic hydrodealkylation of toluene, in the chlorine and nitrogen industries, in phosphorus and phosphoric acid production and in benzene and butadiene production. A new scheme for hydroxylamine production and a new technology for styrene and methanol production have been developed. Direct hydration of propylene has been introduced into the production of isopropanol and propylene ammonolysis has been used to obtain acrylonitrile. Changes in the chemical industry have reduced energy consumption per production unit by 14.2% in the U.S.A. in 1977 in comparison with 1972 and by 14.0% in Common Market countries during 1970-1976.

Increased value creation by industrial refining of natural gas in Norway?; Oekt verdiskaping gjennom industriell foredling av naturgass i Norge?

Energy Technology Data Exchange (ETDEWEB)

Skjelvik, John Magne; Kjelland, Torunn; Bakke, Kathrine Stene; Pedersen, Kent Vincent; Roetnes, Rolf; Fjose, Sveinung

2009-07-01

The report assesses whether industrial exploitation of gas from possible new major discoveries outside Northern Norway could be profitable. Profits are uncertain and depend heavily on gas prices. Industrial exploitation depends on the development of large, capital-intensive plants. This increases the financial risk. In a situation where gas export through pipelines is not an alternative industrial exploitation could be an alternative to export via LNG. However, the pressing demand for natural gas increases the probability of the construction of a gas export pipeline as a realistic alternative. Carbon emissions from a land-based plant will be important, and the costs for trading of emission allowances will reduce profitability. The authorities should allow for industrial exploitation to be assessed on an equal basis with pipeline transport and LNG as alternatives for market solutions for major new discoveries. (EW)

Management of ground water and evolving hydrogeologic studies in New Jersey : a heavily urbanized and industrialized state in the northeastern United States

Science.gov (United States)

Leahy, P. Patrick

1985-01-01

New Jersey is the most densely populated and one of the most industrialized states in the United States. An abundance of freshwater and proximity to major northeastern metropolitan centers has facilitated this development. Pumpage of freshwater from all aquifers in the State in 1980 was 730 million gallons per day (2.76 million cubic meters per day).Management and efficient development of the ground-water resources of the State are the responsibility of the New Jersey Department of Environmental Protection. Laws have been enacted and updated by the State legislature to manage water allocation and to control the disposal of hazardous wastes. Present resource management is guided by the New Jersey Water-Supply Master Plan of 1981. Funding for management activities is partially derived from the sale of state-approved bonds.Effective planning and regional management require accurate and up-to-date hydrologic information and analyses. The U.S. Geological Survey, in cooperation with the New Jersey Geological Survey, is conducting three intensive ground-water studies involving the collection and interpretation of hydrologic data to meet the urgent water-management needs of New Jersey. These studies are part of a long-term cooperative program and are funded through the Water-Supply Bond Act of 1981. They began in 1983 and are scheduled to be completed in 1988.The project areas are situated in the New Jersey part of the Atlantic Coastal Plain in and near Atlantic City, Camden, and South River. They range in size from 400 to 1,200 mil (1,040 to 3,120 km2). The studies are designed to define the geology, hydrology, and geochemistry of the local ground-water systems. The results of these studies will enable the State to address more effectively major problems in these areas such as declining water levels, overpumping, saltwater intrusion, and ground-water contamination resulting from the improper disposal of hazardous wastes.Specific objectives of these studies by the U

Avitourism and Australian Important Bird and Biodiversity Areas.

Science.gov (United States)

Steven, Rochelle; Morrison, Clare; Arthur, J Michael; Castley, J Guy

2015-01-01

Formal protected areas will not provide adequate protection to conserve all biodiversity, and are not always designated using systematic or strategic criteria. Using a systematic process, the Important Bird and Biodiversity Area (IBA) network was designed to highlight areas of conservation significance for birds (i.e. IBA trigger species), and more recently general biodiversity. Land use activities that take place in IBAs are diverse, including consumptive and non-consumptive activities. Avitourism in Australia, generally a non-consumptive activity, is reliant on the IBA network and the birds IBAs aim to protect. However, companies tend not to mention IBAs in their marketing. Furthermore, avitourism, like other nature-based tourism has the potential to be both a threatening process as well as a conservation tool. We aimed to assess the current use of IBAs among Australian-based avitour companies' marketing, giving some indication of which IBAs are visited by avitourists on organised tours. We reviewed online avitour itineraries, recorded sites featuring in descriptions of avitours and which IBA trigger species are used to sell those tours. Of the 209 avitours reviewed, Queensland is the most featured state (n = 59 tours), and 73% feature at least one IBA. Daintree (n = 22) and Bruny Island (n = 17) IBAs are the most popular, nationally. Trigger species represent 34% (n = 254 out of 747) of species used in avitour descriptions. The most popular trigger species' are wetland species including; Brolga (n = 37), Black-necked Stork (n = 30) and Magpie Goose (n = 27). Opportunities exist to increase collaboration between avitour companies and IBA stakeholders. Our results can provide guidance for managing sustainability of the avitourism industry at sites that feature heavily in avitour descriptions and enhance potential cooperation between avitour companies, IBA stakeholders and bird conservation organisations.

Avitourism and Australian Important Bird and Biodiversity Areas.

Directory of Open Access Journals (Sweden)

Rochelle Steven

Full Text Available Formal protected areas will not provide adequate protection to conserve all biodiversity, and are not always designated using systematic or strategic criteria. Using a systematic process, the Important Bird and Biodiversity Area (IBA network was designed to highlight areas of conservation significance for birds (i.e. IBA trigger species, and more recently general biodiversity. Land use activities that take place in IBAs are diverse, including consumptive and non-consumptive activities. Avitourism in Australia, generally a non-consumptive activity, is reliant on the IBA network and the birds IBAs aim to protect. However, companies tend not to mention IBAs in their marketing. Furthermore, avitourism, like other nature-based tourism has the potential to be both a threatening process as well as a conservation tool. We aimed to assess the current use of IBAs among Australian-based avitour companies' marketing, giving some indication of which IBAs are visited by avitourists on organised tours. We reviewed online avitour itineraries, recorded sites featuring in descriptions of avitours and which IBA trigger species are used to sell those tours. Of the 209 avitours reviewed, Queensland is the most featured state (n = 59 tours, and 73% feature at least one IBA. Daintree (n = 22 and Bruny Island (n = 17 IBAs are the most popular, nationally. Trigger species represent 34% (n = 254 out of 747 of species used in avitour descriptions. The most popular trigger species' are wetland species including; Brolga (n = 37, Black-necked Stork (n = 30 and Magpie Goose (n = 27. Opportunities exist to increase collaboration between avitour companies and IBA stakeholders. Our results can provide guidance for managing sustainability of the avitourism industry at sites that feature heavily in avitour descriptions and enhance potential cooperation between avitour companies, IBA stakeholders and bird conservation organisations.

Avitourism and Australian Important Bird and Biodiversity Areas

Science.gov (United States)

Steven, Rochelle; Morrison, Clare; Arthur, J. Michael; Castley, J. Guy

2015-01-01

Formal protected areas will not provide adequate protection to conserve all biodiversity, and are not always designated using systematic or strategic criteria. Using a systematic process, the Important Bird and Biodiversity Area (IBA) network was designed to highlight areas of conservation significance for birds (i.e. IBA trigger species), and more recently general biodiversity. Land use activities that take place in IBAs are diverse, including consumptive and non-consumptive activities. Avitourism in Australia, generally a non-consumptive activity, is reliant on the IBA network and the birds IBAs aim to protect. However, companies tend not to mention IBAs in their marketing. Furthermore, avitourism, like other nature-based tourism has the potential to be both a threatening process as well as a conservation tool. We aimed to assess the current use of IBAs among Australian-based avitour companies’ marketing, giving some indication of which IBAs are visited by avitourists on organised tours. We reviewed online avitour itineraries, recorded sites featuring in descriptions of avitours and which IBA trigger species are used to sell those tours. Of the 209 avitours reviewed, Queensland is the most featured state (n = 59 tours), and 73% feature at least one IBA. Daintree (n = 22) and Bruny Island (n = 17) IBAs are the most popular, nationally. Trigger species represent 34% (n = 254 out of 747) of species used in avitour descriptions. The most popular trigger species’ are wetland species including; Brolga (n = 37), Black-necked Stork (n = 30) and Magpie Goose (n = 27). Opportunities exist to increase collaboration between avitour companies and IBA stakeholders. Our results can provide guidance for managing sustainability of the avitourism industry at sites that feature heavily in avitour descriptions and enhance potential cooperation between avitour companies, IBA stakeholders and bird conservation organisations. PMID:26701779

Matlab laser toolbox

NARCIS (Netherlands)

Römer, Gerardus Richardus, Bernardus, Engelina; Huis in 't Veld, Bert; Schmidt, M.; Vollertsen, F.; Geiger, M.

2010-01-01

Matlab® is a program for numeric computation, simulation and visualization, developed by The Mathworks, Inc. It is used heavily in education, research, and industry, for solving general, as well as application area-specific problems, that arise in various disciplines. For this purpose Matlab has

Electronics Industry

National Research Council Canada - National Science Library

Ginter, Michael J; Andersen, James L; Becker, John A; Belliveau, Gerald E; Eppich, Frank J; Awai, Herman T; Hanko, David J; Hughes, Bob; Jones, Douglas; Larson, Kelly J

2007-01-01

.... area, New York State, Silicon Valley (California), Taiwan, and China. This approach provides a wide range of perspectives from which to examine the selected industry's current condition, outlook, and challenges...

Marine organic geochemistry in industrially affected coastal areas in Greece: Hydrocarbons in surface sediments

Science.gov (United States)

Hatzianestis, Ioannis

2015-04-01

Hydrocarbons are abundant components of the organic material in coastal zones. Their sources are mainly anthropogenic, but several natural ones have also been recognized. Among hydrocarbons, the polycyclic aromatic ones (PAHs) have received special attention since they considered as hazardous environmental chemicals and are included in priority pollutant lists. The purpose of this study was to investigate the distribution, sources and transport pathways of hydrocarbons in marine areas in Greece directly influenced from the operation of major industrial units in the coastal zone by using a molecular marker approach, characteristic compositional patterns and related indices and also to evaluate their potential toxicity. Thirty two surface sediment samples were collected from three marine areas: a) Antikyra bay in Korinthiakos gulf, affected from the operation of an alumina and production plant b) Larymna bay in Noth Evoikos, affected from the operation of a nickel production plant and c) Aliveri bay in South Evoikos Gulf, affected from a cement production plant. In all the studied areas aquaculture and fishing activities have been also developed in the coastal zone. High aliphatic hydrocarbon (AHC) concentrations (~500 μg/g), indicating significant petroleum related inputs, were measured only in Antikyra bay. In all the other samples, AHC values were below 100 μg/g. N-alkanes were the most prominent resolved components (R) with an elevated odd to even carbon number preference, revealing the high importance of terrestrial inputs in the study areas. The unresolved complex mixture (UCM) was the major component of the aliphatic fraction (UCM/R > 4), indicating a chronic oil pollution. A series of hopanes were also identified, with patterns characteristic of oil-derived hydrocarbons, further confirming the presence of pollutant inputs from fossil fuel products. Extremely high PAH concentrations (> 100,000 ng/g) were found in the close vicinity of the alumina production

Marine reserves and reproductive biomass: a case study of a heavily targeted reef fish.

Directory of Open Access Journals (Sweden)

Brett M Taylor

Full Text Available Recruitment overfishing (the reduction of a spawning stock past a point at which the stock can no longer replenish itself is a common problem which can lead to a rapid and irreversible fishery collapse. Averting this disaster requires maintaining a sufficient spawning population to buffer stochastic fluctuations in recruitment of heavily harvested stocks. Optimal strategies for managing spawner biomass are well developed for temperate systems, yet remain uncertain for tropical fisheries, where the danger of collapse from recruitment overfishing looms largest. In this study, we explored empirically and through modeling, the role of marine reserves in maximizing spawner biomass of a heavily exploited reef fish, Lethrinus harak around Guam, Micronesia. On average, spawner biomass was 16 times higher inside the reserves compared with adjacent fished sites. Adult density and habitat-specific mean fish size were also significantly greater. We used these data in an age-structured population model to explore the effect of several management scenarios on L. harak demography. Under minimum-size limits, unlimited extraction and all rotational-closure scenarios, the model predicts that preferential mortality of larger and older fish prompt dramatic declines in spawner biomass and the proportion of male fish, as well as considerable declines in total abundance. For rotational closures this occurred because of the mismatch between the scales of recovery and extraction. Our results highlight how alternative management scenarios fall short in comparison to marine reserves in preserving reproductively viable fish populations on coral reefs.

Ecological Study on Hospitalizations for Cancer, Cardiovascular, and Respiratory Diseases in the Industrial Area of Etang-de-Berre in the South of France

Directory of Open Access Journals (Sweden)

Laurence Pascal

2013-01-01

Full Text Available The Etang-de-Berre area is a large industrialized area in the South of France, exposing 300,000 inhabitants to the plumes of its industries. The possible associated health risks are of the highest concern to the population, who asked for studies investigating their health status. A geographical ecological study based on standardized hospitalizations ratios for cancer, cardiovascular, and respiratory diseases was carried out over the 2004–2007 period. Exposure to air pollution was assessed using dispersion models coupled with a geographic information system to estimate an annual mean concentration of sulfur dioxide (SO2 for each district. Results showed an excess risk of hospitalization for myocardial infarction in women living in districts with medium or high SO2 exposure, respectively, 38% [CI 95% 4 : 83] and 54% [14 : 110] greater than women living in districts at the reference level exposure. A 26% [2 : 57] excess risk of hospitalization for myocardial infarction was also observed in men living in districts with high SO2 levels. No excess risk of hospitalization for respiratory diseases or for cancer was observed, except for acute leukemia in men only. Results illustrate the impact of industrial air pollution on the cardiovascular system and call for an improvement of the air quality in the area.

FINANCIAL MANAGEMENT IN THE FAMILY AND NON-FAMILY SME´S IN THE TEXTILE INDUSTRY IN MEXICO

OpenAIRE

Martha Isabel Bojorquez Zapata; Antonio Emmanuel Perez Brito; Jorge Humberto Basulto Triay

2014-01-01

In this paper, we analyze differences in financial management practices between family and non-family Small and Medium Enterprises (SMEs) in the textile industry. We hypothesize that family SMEs use different sources of funding for new investments, tend to have less debt, are more profitable and use less financial and accounting information for decision making than non-family SMEs. We survey 24 textile SMEs located in Yucatan, Mexico. The results show that family SMEs rely more heavily on int...

Energy intensive industry for Alaska. Volume I: Alaskan cost factors; market factors; survey of energy-intensive industries

Energy Technology Data Exchange (ETDEWEB)

Swift, W.H.; Clement, M.; Baker, E.G.; Elliot, D.C.; Jacobsen, J.J.; Powers, T.B.; Rohrmann, C.A.; Schiefelbein, G.L.

1978-09-01

The Alaskan and product market factors influencing industry locations in the state are discussed and a survey of the most energy intensive industries was made. Factors external to Alaska that would influence development and the cost of energy and labor in Alaska are analyzed. Industries that are likely to be drawn to Alaska because of its energy resources are analyzed in terms of: the cost of using Alaska energy resources in Alaska as opposed to the Lower 48; skill-adjusted wage and salary differentials between relevant Alaskan areas and the Lower 48; and basic plant and equipment and other operating cost differentials between relevant Alaskan areas and the Lower 48. Screening and evaluation of the aluminum metal industry, cement industry, chlor-alkali industry, lime industry, production of methanol from coal, petroleum refining, and production of petrochemicals and agrichemicals from North Slope natural gas for development are made.

Empoderamiento sanitario en entidades laborales de la zona industrial de Santiago de Cuba Health empowerment in working entities of the industrial area of Santiago de Cuba

Directory of Open Access Journals (Sweden)

Soraya Victoria Samada Durán

2013-02-01

Full Text Available Se realizó una intervención comunitaria en los trabajadores de 30 entidades laborales ubicadas en la zona industrial del municipio de Santiago de Cuba, durante el bienio 2009-2010, para establecer el empoderamiento sanitario en ellos. Entre los principales resultados figuró el logro de la capacitación de todos los líderes sindicales y políticos, así como de la brigada de vigilancia y lucha antivectorial, por el contrario de los dirigentes administrativos, de los cuales solo 86,6 % participó en el estudio porque no lo consideraban una responsabilidad inherente a su cargo. Respecto a la situación ambiental, se observó un incremento de los criaderos de Aedes aegypti durante la temporada lluviosa, asociado a una mayor acumulación de agua en los depósitos naturales o artificiales, o ambos; no obstante, hubo un impacto social en el ordenamiento del medio en 9 de estas instituciones a través de la integración de los intereses comunitarios, la planificación en conjunto y la evaluación participativa, que conformó la principal estrategia. Finalmente, se recomendó implementar este proceso de empoderamiento sanitario en el resto de los centros de trabajo de la zona industrial con vistas a prevenir las enfermedades transmitidas por mosquitos y roedores.A community intervention was performed in workers of 30 entities located in the industrial area of Santiago de Cuba municipality during the biennium 2009 -2010 to establish the health empowerment in them. Among the main results was the training for all union and political leaders and antivectorial surveillance and control brigade, unlike administrative leaders, of whom only 86.6% participated in the study because they considered it was not their responsibility. Regarding the environmental conditions, an increment of Aedes aegypti breeding sites was observed during the rainy season, associated with increased accumulation of water in natural or artificial reservoirs or both. However, there was

Misdiagnosis of X-linked retinitis pigmentosa in a choroideremia patient with heavily pigmented fundi.

Science.gov (United States)

Nanda, A; Salvetti, A P; Martinez-Fernandez de la Camara, C; MacLaren, R E

2018-06-01

Inherited retinal diseases are thought to be the leading cause of sight loss in the working age population. Mutations found in the RPGR and CHM genes cause retinitis pigmentosa (RP) and choroideremia, respectively. In the first instance, an X-linked family history of visual field loss commonly raises the suspicion of one of these two genes. In choroideremia, the classic description of a white fundal reflex secondary to the widespread chorioretinal degeneration was made over a hundred years ago in Caucasians. But, it is not so obvious in heavily pigmented fundi. Hence, the clinical diagnosis of CHM in non-Caucasian patients may be challenging in the first stages of the disease. Here we report a case of a Southeast Asian gentleman who has a family history of X-linked retinal degeneration and was found to have a confirmed in-frame deletion of 12 DNA nucleotides in exon 15 of the RPGR gene. Later in life, however, his fundal appearance showed unusual areas of circular pigment hypertrophy and clumping. He was therefore tested for carrying a disease-causing mutation in the CHM gene and a null mutation was found. Since gene therapy trials are ongoing for both of these conditions, it has now become critically important to establish the correct genetic diagnosis in order to recruit suitable candidates. Moreover, this case demonstrates the necessity to remain vigilant in the interpretation of genetic results which are inconsistent with clinical features.

Design and assessment of urban drainage and water reuse systems for the reconstruction of formerly industrial areas: a case in Beijing.

Science.gov (United States)

Liu, L; Zeng, S; Dong, X; Chen, J

2013-01-01

The Shougang Group is an industrial steel enterprise occupying 800 ha in Beijing that will cease production by 2010. The area will be converted to a new financial and commercial zone. The rebuilding of the water infrastructure in this area should address water shortages in Beijing and retain the industrial landmark of a large cooling water tank. A design framework and an assessment system with 11 indicators were developed for this purpose. Four reconstruction schemes are presented here. Scheme 1 is a traditional system that completely depends on outside the municipal facility. Schemes 2, 3, and 4 are systems to separately discharge greywater and blackwater. Scheme 4 uses a vacuum system that allows the reclamation of nutrients. Schemes 2 and 4 use wetland-treated greywater to fill the water tank. Scheme 3 reuses greywater for toilets after on-site treatment. Scheme 2 is recommended due to its lower cost, greater environmental benefit, moderate resource reclamation, and higher technical feasibility.

Exposing and addressing tobacco industry conduct in low-income and middle-income countries.

Science.gov (United States)

Gilmore, Anna B; Fooks, Gary; Drope, Jeffrey; Bialous, Stella Aguinaga; Jackson, Rachel Rose

2015-03-14

The tobacco industry's future depends on increasing tobacco use in low-income and middle-income countries (LMICs), which face a growing burden of tobacco-related disease, yet have potential to prevent full-scale escalation of this epidemic. To drive up sales the industry markets its products heavily, deliberately targeting non-smokers and keeps prices low until smoking and local economies are sufficiently established to drive prices and profits up. The industry systematically flaunts existing tobacco control legislation and works aggressively to prevent future policies using its resource advantage to present highly misleading economic arguments, rebrand political activities as corporate social responsibility, and establish and use third parties to make its arguments more palatable. Increasingly it is using domestic litigation and international arbitration to bully LMICs from implementing effective policies and hijacking the problem of tobacco smuggling for policy gain, attempting to put itself in control of an illegal trade in which there is overwhelming historical evidence of its complicity. Progress will not be realised until tobacco industry interference is actively addressed as outlined in Article 5.3 of the Framework Convention on Tobacco Control. Exemplar LMICs show this action can be achieved and indicate that exposing tobacco industry misconduct is an essential first step. Copyright © 2015 Elsevier Ltd. All rights reserved.

Competition in the electricity supply industry. Experiences from Europe and the United States

International Nuclear Information System (INIS)

Olsen, O.J.

1995-01-01

Introducing competition in the electricity industry is a major social experiment. Historically, the industry has been heavily regulated, however, this is no longer the case. Production and sales are being opened for competition and separated from the network services, transmission and distribution. This book includes papers from a Nordic Conference held in September 1994 in Copenhagen. The conference was planned as a part of the Energy Research Programme under the Nordic Council of Ministers and the object was to discuss the Nordic experience of competition in the electricity industry in comparison with other Western countries. The U.K. was the first European country to introduce competition in its electricity industry. Norway came next and two other Nordic countries - Sweden and Finland - have decided to follow suit. The U.S. started earlier than the European countries opening for limited competition in power production. However, the background of the reforms and its approach in the U.S. is different from Europe and far less radical. The experience of two Central European countries - Germany and The Netherlands - is also included in this book. Both countries have many institutional similarities to the Nordic countries, but they are - together with Denmark - more hesitant about introducing competition in their electricity industries. (au)

Climatic change in Mediterranean area

International Nuclear Information System (INIS)

Manos, A.

1991-01-01

United Nations Environmental Program (UNEP) studies on forecasted greenhouse climatic effects on the Mediterranean coastal and marine ecosystems and regional socio-economic framework have indicated the need for a concerted plan of protective and remedial action. The studies considered rises of 1.5 degrees in ambient temperature and 20 centimeters in sea level occurring before the year 2025. A regional, as opposed to a global area, study approach was adopted since the severity of climatic effects is expected to vary greatly from one part of the world to another. The specific areas investigated were the Po River Delta and Venezia Lagoon in Italy, the Nile Delta, Camargue, the Ebro Delta, the Tunisian National Park area, and the Thermaicos Gulf in Greece. The rise in average temperature is expected to negatively effect Mediterranean agricultural production and the coastal and marine ecosystems due to prolonged periods of drought and exceptional rainfall. It is suggested that a system of dikes be constructed to protect the coastal areas which are heavily dependent on tourism and agriculture

Industrial accidents in radiological controlled areas: the importance of radiation protection in the organisation of the emergency aid

International Nuclear Information System (INIS)

Fenolland, J.L.; Laporte, E.

2003-01-01

After some disappointments when the first French nuclear units were started, it became clear that all the aspects linked to radio-protection needed to be taken into account in the context of emergency aid in the case of an industrial accident in radiological controlled area. In the case of an accident involving people, on-site first aid is provided by permanent services of the power plant. These teams are trained in first aid and fire-fighting. They are well trained in radioprotection. The specificity of an industrial event in controlled zone is that the victims' conventional injuries, whether it be a wound, a burn or a fracture, can be complicated by radioactive contamination. If it is justified, the exterior emergency services (firemen and medical teams) sire immediately called in. These teams are not necessarily trained in radioprotection. (authors)

Mineralogy and origin of atmospheric particles in the industrial area of Huelva (SW Spain)

Science.gov (United States)

Bernabé, J. M.; Carretero, M. I.; Galán, E.

The mineralogy of atmospheric particles at the confluence of the Tinto and Odiel rivers, south of Huelva (a highly industrialized city in the SW Spain), was characterized in view to identify source origins. In spite of the small amount of sample collected, mineralogical characterization was performed by X-ray diffraction, polarized light microscopy and scanning electron microscopy with EDS analysis system, using an adequate sample preparation methodology. Sedimentable (SP) and aerosols particles were sampled an one-week basis every two months for one year. Quartz, calcite and feldspars were found to be the major minerals in both fractions, and phyllosilicates, dolomite and gypsum were also identified in lower content. Minor mineral particles included barite, apatite, sphalerite and pyrite. SEM studies revealed the additional presence of chalcopyrite in both SP and aerosols, and of chalcocite-covellite, halite and sylvite in the latter. Siderite, hematite and ankerite were only detected in the SP fraction. The concentrations of the previous minerals increased in summer by effect of the limited rain and the resulting scarcity of atmosphere washing. Non-mineral particles detected by SEM in SP and aerosol fractions included spherical, biological and compositionally complex particles. The main source of mineral particles was found to be the soil suspension in addition to the metallurgical and fertilizer production industries in the area.

Chemical profile of size-fractionated soils collected in a semiarid industrial area of Argentina

Science.gov (United States)

Morales Del Mastro, Anabella; Pereyra, Marcelo; Londonio, Agustín; Pereyra, Victoria; Rebagliati, Raúl Jiménez; Dawidowski, Laura; Gómez, Darío; Smichowski, Patricia

2014-12-01

A study was undertaken to assess the chemical profile of soil collected in Bahía Blanca (Argentina). In this industrial city, semiarid soils are affected by different industrial and agricultural activities, the presence of a saltpeter extraction facility, traffic and increasing urbanization. Sixteen soil samples (superficial and sub-superficial) were collected. Samples were sieved in two fractions (A plasma optical emission spectrometry (ICP OES). Anions (Cl-, F-, SO42-) and cations (K+, Na+ and NH4+) were determined by high performance liquid chromatography (HPLC) after an aqueous extraction. As expected, crustal elements namely, Al, Ca, Fe, Mg and Ti exhibited the highest concentrations. Mean elemental concentration ranged from Na+ ≅ SO42- > K+ > NO3-. Three indicators, namely, (i) coefficient of variation, (ii) coefficient of divergence and (iii) ratio of elemental concentration with respect to Ca were used to assess chemical, spatial and inter-profile variability. Chloride > Ca > Na+ > Mo > SO42-, dominated the variability indicating that these are key chemical markers for future assessment of crustal contribution to airborne particles in the area. The ratios Xi/Ca allowed discriminating the soil of the semi-arid region surrounding Bahía Blanca. The chemical profiles obtained in this study, particularly those of topsoil, will be a key input to characterize soil resuspension and its contribution to airborne particulate matter in a forthcoming receptor model analysis.

Identification of active erosion areas and areas at risk by remote sensing: an example in the Esera Isabena watershed, Central Spanish Pyrenees

International Nuclear Information System (INIS)

Alatorre, L. C.; Begueria, S.; Vicente Serrano, S. M.

2009-01-01

The identification of eroded areas at basin scale can be very useful for environmental planning and can help to reduce land degradation and sediments yield. In this paper remote sensing technique are used to discriminate eroded areas and areas at risk in a badlands landscape developed on Eocene marls. In the Esera Isabena watershed (Spanish Pyrenees). The spatial distribution, the scarce vegetal cover and the high level of erosion let a good visual and digital discrimination of badlands, as opposed to other land covers and surfaces. A maximum likelihood supervised method was used to discriminate heavily eroded areas (badlands) from scarce or densely vegetated lands. the classification distance was used to obtain thresholds for eroded areas and areas at risk. Two error statistics (sensitivity and specificity), where used to determine the most adequate threshold values. The resulting map shows that most areas at risk are located surrounding the badlands areas. (Author) 8 refs.

Identification of active erosion areas and areas at risk by remote sensing: an example in the Esera Isabena watershed, Central Spanish Pyrenees

Energy Technology Data Exchange (ETDEWEB)

Alatorre, L. C.; Begueria, S.; Vicente Serrano, S. M.

2009-07-01

The identification of eroded areas at basin scale can be very useful for environmental planning and can help to reduce land degradation and sediments yield. In this paper remote sensing technique are used to discriminate eroded areas and areas at risk in a badlands landscape developed on Eocene marls. In the Esera Isabena watershed (Spanish Pyrenees). The spatial distribution, the scarce vegetal cover and the high level of erosion let a good visual and digital discrimination of badlands, as opposed to other land covers and surfaces. A maximum likelihood supervised method was used to discriminate heavily eroded areas (badlands) from scarce or densely vegetated lands. the classification distance was used to obtain thresholds for eroded areas and areas at risk. Two error statistics (sensitivity and specificity), where used to determine the most adequate threshold values. The resulting map shows that most areas at risk are located surrounding the badlands areas. (Author) 8 refs.

Assessment of industry needs for oil shale research and development

Energy Technology Data Exchange (ETDEWEB)

Hackworth, J.H.

1987-05-01

Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry's view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.

Mercury pollution control in industrial area in Rosignano Marittimo (Italy) during last twenty years (1971-1991)

International Nuclear Information System (INIS)

Bertani, R.

1995-01-01

Author takes into account some papers dealing with mercury environmental pollution, appeared in different scientific journals over the last twenty years, in the aim of defining a homogeneous frame for the comprehension of the environmental situation development. Data relating to air, marine water, sediments, animal and vegetal organisms, show a consistent decreasing of mercury emissions with the passing of time. Nevertheless, author fearfully points out the environmental fate of the mercury which has been heavily released from the plant in the past years and to whom he wishes to turn attention for the assessment of an adequate control procedure

Mapping of wine industry

Directory of Open Access Journals (Sweden)

Віліна Пересадько

2016-10-01

Full Text Available Having reviewed a variety of approaches to understanding the essence of wine industry, having studied the modern ideas about the future of wine industry, having analyzed more than 50 maps from the Internet we have set the trends and special features of wine industry mapping in the world, such as: - the vast majority of maps displays the development of the industry at regional or national level, whereas there are practically no world maps; - wine-growing regions are represented on maps very unevenly; - all existing maps of the industry could be classified as analytical ascertaining inventory type; - the dominant ways of cartographic representation are area method and qualitative background method, sign method and collation maps are rarely used; - basically all the Internet maps have low quality as they are scanned images with poor resolution; - the special feature of maps published lately is lack of geographical basis (except for state borders and coastline. We created wine production and consumption world map «Wine Industry» in the scale of 1:60 000 000 with simple geographical basis (state names, state borders, major rivers, coastline. It was concluded that from the methodological point of view it is incorrect not to show geographical basis on maps of wine industry. Analysis of this map allowed us to identify areas of traditional wine-making, potential wine-making areas and countries which claim to be the world leaders in the field of wine production. We found disbalans between wine production and wine consumption - increasing wine production in South America, China and the United States and increasing wine consumption (mainly due to the import products in countries where the grape is not the primary agricultural product.

The propulsive industry; oil and gas breed a community of builders

International Nuclear Information System (INIS)

Jaremko, G.

2000-01-01

The role that government-industry cooperation has played in the development of the Canadian petroleum industry is recounted by way of providing background to delegates to the World Petroleum Congress taking place in June 2000 in Calgary, Alberta. Among individuals whose contributions have been vital to the development of the industry are the late Premier Manning of Alberta, and J. Howard Pew, President of Sun Corporation, Todd Montgomery, Michael Supple, Chris Hopkins, the triumvirate leaders of the privately owned SynEnCo Inc., the latest entry into the oilsands lineup, Dave Beckwerment and Jeff Arsenych, the visionaries behind Ravenwood Resources Inc., Robert McLeay, founder of Mera Petroleum Inc., and Robert Mansell, the economist who keeps tab on the industry from his home base at the University of Calgary. According to Mansell, four-fifths of Canadian oil and gas production is located in Alberta, which constitutes some 45 per cent of the country's economy. From manufacturing to communications and information technology, other sectors draw heavily on the oil and gas community for customers and talent. Despite occasional disparaging remarks applied to the industry as being 'a mature and sunset industry' it survives through its visionaries and adventurers who flourish in a cross-section of the community built by earlier pioneers, in various niches ranging from economical drilling for modest conventional reserves to international hunts for proverbial elephant-sized discoveries in world trouble spots. The staying power of the industry through upheavals of global proportions underlines the talent and policies that manage the Canadian petroleum industry, and provide an indication of the scale of the country's natural resources

Anomalous transmission through heavily doped conducting polymer films with periodic subwavelength hole array

Science.gov (United States)

Matsui, Tatsunosuke; Vardeny, Z. Valy; Agrawal, Amit; Nahata, Ajay; Menon, Reghu

2006-08-01

We observed resonantly enhanced (or anomalous transmission) terahertz transmission through two-dimensional (2D) periodic arrays of subwavelength apertures with various periodicities fabricated on metallic organic conducting polymer films of polypyrrole heavily doped with PF 6 molecules [PPy(PF6)]. The anomalous transmission spectra are in good agreement with a model involving surface plasmon polariton excitations on the film surfaces. We also found that the resonantly enhanced transmission peaks are broader in the exotic metallic PPy(PF6) films compared to those formed in 2D aperture array in regular metallic films such as silver, indicating that the surface plasmon polaritons on the PPy(PF6) film surfaces have higher attenuation.

Plastic Technology (Production). Industrial Arts, Senior High--Level II. North Dakota Senior High Industrial Arts Curriculum Guides.

Science.gov (United States)

Claus, Robert; And Others

This course guide for a plastic technology course is one of four developed for the production area in the North Dakota senior high industrial arts education program. (Eight other guides are available for two other areas of Industrial Arts--energy/power and graphic communications.) Part 1 provides such introductory information as a definition and…

Using a source-receptor approach to characterise VOC behaviour in a French urban area influenced by industrial emissions. Part II: source contribution assessment using the Chemical Mass Balance (CMB) model.

Science.gov (United States)

Badol, Caroline; Locoge, Nadine; Galloo, Jean-Claude

2008-01-25

In Part I of this study (Badol C, Locoge N, Leonardis T, Gallo JC. Using a source-receptor approach to characterise VOC behaviour in a French urban area influenced by industrial emissions, Part I: Study area description, data set acquisition and qualitative data analysis of the data set. Sci Total Environ 2007; submitted as companion manuscript.) the study area, acquisition of the one-year data set and qualitative analysis of the data set have been described. In Part II a source profile has been established for each activity present in the study area: 6 profiles (urban heating, solvent use, natural gas leakage, biogenic emissions, gasoline evaporation and vehicle exhaust) have been extracted from literature to characterise urban sources, 7 industrial profiles have been established via canister sampling around industrial plants (hydrocarbon cracking, oil refinery, hydrocarbon storage, lubricant storage, lubricant refinery, surface treatment and metallurgy). The CMB model is briefly described and its implementation is discussed through the selection of source profiles and fitting species. Main results of CMB modellings for the Dunkerque area are presented. (1) The daily evolution of source contributions for the urban wind sector shows that the vehicle exhaust source contribution varies between 40 and 55% and its relative increase at traffic rush hours is hardly perceptible. (2) The relative contribution of vehicle exhaust varies from 55% in winter down to 30% in summer. This decrease is due to the increase of the relative contribution of hydrocarbon storage source reaching up to 20% in summer. (3) The evolution of source contributions with wind directions has confirmed that in urban wind sectors the contribution of vehicle exhaust dominate with around 45-55%. For the other wind sectors that include some industrial plants, the contribution of industrial sources is around 60% and could reach 80% for the sector 280-310 degrees , which corresponds to the most dense

Physical parameters of groundwater as indicators of pollution in industrial areas of Taxila, Wah and Hasanabdal

International Nuclear Information System (INIS)

Khan, M.S.; Zaheer-ud-Dln-Qureshi

2004-01-01

The Wah area historically famous for having sweet aquifer system is greatly effected due to environmental activities, such as industrialization and poor sewage system in the recent past. Thirty water samples have been collected from dug wells penetrating to shallow two layers in a multi layered aquifer system. The shallow aquifer is located at a depth of 45-85 feet and composed of very fine grained sand to silt in two layers separated by silty clay. To assess the contamination problems, physical parameters of groundwater such as temperature, color, turbidity, odour and taste have been estimated fifty percent of the dug wells have been found as contaminated and not fit for human consumption according 10 WHO standards. High values of electrical conductance determined in fifty percent of wells show trends of chemical contamination and their probable sources near by these wells against the general recharge pattern prevailing in the area can be located. (author)

Estimating representative background PM2.5 concentration in heavily polluted areas using baseline separation technique and chemical mass balance model

Science.gov (United States)

Gao, Shuang; Yang, Wen; Zhang, Hui; Sun, Yanling; Mao, Jian; Ma, Zhenxing; Cong, Zhiyuan; Zhang, Xian; Tian, Shasha; Azzi, Merched; Chen, Li; Bai, Zhipeng

2018-02-01

The determination of background concentration of PM2.5 is important to understand the contribution of local emission sources to total PM2.5 concentration. The purpose of this study was to exam the performance of baseline separation techniques to estimate PM2.5 background concentration. Five separation methods, which included recursive digital filters (Lyne-Hollick, one-parameter algorithm, and Boughton two-parameter algorithm), sliding interval and smoothed minima, were applied to one-year PM2.5 time-series data in two heavily polluted cities, Tianjin and Jinan. To obtain the proper filter parameters and recession constants for the separation techniques, we conducted regression analysis at a background site during the emission reduction period enforced by the Government for the 2014 Asia-Pacific Economic Cooperation (APEC) meeting in Beijing. Background concentrations in Tianjin and Jinan were then estimated by applying the determined filter parameters and recession constants. The chemical mass balance (CMB) model was also applied to ascertain the effectiveness of the new approach. Our results showed that the contribution of background PM concentration to ambient pollution was at a comparable level to the contribution obtained from the previous study. The best performance was achieved using the Boughton two-parameter algorithm. The background concentrations were estimated at (27 ± 2) μg/m3 for the whole year, (34 ± 4) μg/m3 for the heating period (winter), (21 ± 2) μg/m3 for the non-heating period (summer), and (25 ± 2) μg/m3 for the sandstorm period in Tianjin. The corresponding values in Jinan were (30 ± 3) μg/m3, (40 ± 4) μg/m3, (24 ± 5) μg/m3, and (26 ± 2) μg/m3, respectively. The study revealed that these baseline separation techniques are valid for estimating levels of PM2.5 air pollution, and that our proposed method has great potential for estimating the background level of other air pollutants.

Very heavily electron-doped CrSi2 as a high-performance high-temperature thermoelectric material

International Nuclear Information System (INIS)

Parker, David; Singh, David J

2012-01-01

We analyze the thermoelectric behavior, using first principles and Boltzmann transport calculations, of very heavily electron-doped CrSi 2 and find that at temperatures of 900-1250 K and electron dopings of 1-4 × 10 21 cm -3 , thermopowers as large in magnitude as 200 μV K -1 may be found. Such high thermopowers at such high carrier concentrations are extremely rare, and suggest that excellent thermoelectric performance may be found in these ranges of temperature and doping. (paper)

An insight into recent consanguinity within the Basque area in Spain. Effects of autochthony, industrialization and demographic changes.

Science.gov (United States)

Alfonso-Sanchez, M A; Peña, J A; Aresti, U; Calderón, R

2001-01-01

The importance of studying the genetic kinship of those human groups characterized by a deeply rooted ethnicity has traditionally been and still is an interesting goal of anthropological and population genetic studies. However, only a few surveys have aimed to learn about the impact of industrial development on the consanguinity of these populations and even those have concentrated on industrialized regions. This approach is worth analysing in Spain, where industrialization was late in relation to other western European countries. In this work we analyse the characteristics of inbreeding in Guipúzcoa from 1951 to 1995. This Basque province underwent industrial and tourist development earlier than other Spanish regions. It has the highest density of Basque speakers and has always occupied a central position within the map of distribution of the Basque language. Guipúzcoa is geographically placed in the core of the Basque area. SUDJECTS AND METHODS: Data on consanguineous marriages recorded in the province of Guipúzcoa between 1951 and 1995 were taken from Roman Catholic dispensations stored in the Diocesan Archives of San Sebastián, the province's capital city. Over the whole time period, a total of 1152 consanguineous marriages were registered. The high frequencies of first cousin (M22) (F = 1/16) and uncle-niece, aunt-nephew (M12) (F = 1/8) consanguineous marriages distinguish Guipúzcoa from the rest of Iberian populations. The M22/M33 ratio (with M33 being second cousins) has never dropped below 0.67, which represents a significant deviation from the expectation value of 0.25. When consanguineous marriages are classified according to marriage partner birthplaces interesting results emerge. Provincial endogamy shows the highest consanguinity rates (57%) and the proportion of M22/M33 is also rather high (0.63). However, a major contribution to the consanguinity levels and mean inbreeding coefficient recorded in Guipúzcoa over recent decades has been made by

Air quality of the industrial area of Padova. SO2 and micropollutants concentration measurements around the incenerator of domestic wastes

Energy Technology Data Exchange (ETDEWEB)

Baracco, L [Amministrazione Provinciale di Padova; Boschi, G

1986-04-01

Some data related to one year measurements of SO2 concentrations and of suspended solid particles taken by Environmental Monitoring Station of the Provincial Network of Padua, located near the Industrial Area, are reported. In addition is reported a series of analytical determinations of heavy metals and organic micropollutants carried out in the same area by the Municipal Refuse Collection and public Health Services. The obtained results indicate that the concentration of SO2 in the area is well within the law limits while, as far as the suspended solid particles are concerned, it points out that the respect of the imposed limits, must be carefully evaluated in regards to new urbans developments and air cleaning plants which are going to be arranged by the Veneto.

Inkjet printing as a roll-to-roll compatible technology for the production of large area electronic devices on a pre-industrial scale

NARCIS (Netherlands)

Teunissen, P.; Rubingh, E.; Lammeren, T. van; Abbel, R.J.; Groen, P.

2014-01-01

Inkjet printing is a promising approach towards the solution processing of electronic devices on an industrial scale. Of particular interest is the production of high-end applications such as large area OLEDs on flexible substrates. Roll-to-roll (R2R) processing technologies involving inkjet

Final construction quality assurance report for the Y-12 Industrial Landfill V, Area 2, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Bessom, W.H.

1996-11-01

Lockheed Martin Energy Systems (LMES) has finished construction of Area 2 of the Y-12 Plant Industrial Landfill (ILF-V), classified as a Class 2 Landfill. This final Construction Quality Assurance (CQA) Report provides documentation that Area 2 was constructed in substantial compliance with the Tennessee Department of Environment and Conservation (TDEC) approved design, as indicated and specified in the permit drawings, approved changes, and specifications. This report applies specifically to the Area 2 excavation, compacted clay soil liner, geomembrane liner, granular leachate collection layer, protective soil cover, and the leachate collection system. An ''As-Built'' survey was performed and is included. The drawings provide horizontal and vertical information for Area 2, the anchor trench, the leachate collection pipe, the temporary access road, and cross-sections of Area 2. This report provides documentation of the following items: the excavation activities of Area 2; the maximum recompacted coefficient of hydraulic conductivity or permeability of the soil is less than 1 x 10 -7 centimeters per second (cm/sec); the total thickness of the compacted clay soil liner equals a minimum of 2 feet; a 40 mil impermeable geomembrane (polypropylene) flexible membrane liner (FML) and 16 oz. geotextile fabric was placed in direct contact with the compacted clay soil liner; a 12 inch granular leachate collection layer was installed and covered with a 8 oz. geotextile separation fabric; the installation of the leachate collection piping; and the two foot protective clay soil cover

Large expansion of oil industry in the Ecuadorian Amazon: biodiversity vulnerability and conservation alternatives.

Science.gov (United States)

Lessmann, Janeth; Fajardo, Javier; Muñoz, Jesús; Bonaccorso, Elisa

2016-07-01

Ecuador will experience a significant expansion of the oil industry in its Amazonian region, one of the most biodiverse areas of the world. In view of the changes that are about to come, we explore the conflicts between oil extraction interests and biodiversity protection and apply systematic conservation planning to identify priority areas that should be protected in different oil exploitation scenarios. First, we quantified the current extent of oil blocks and protected zones and their overlap with two biodiversity indicators: 25 ecosystems and 745 species (whose distributions were estimated via species distribution models). With the new scheme of oil exploitation, oil blocks cover 68% (68,196 km(2)) of the Ecuadorian Amazon; half of it occupied by new blocks open for bids in the southern Amazon. This region is especially vulnerable to biodiversity losses, because peaks of species diversity, 19 ecosystems, and a third of its protected zones coincide spatially with oil blocks. Under these circumstances, we used Marxan software to identify priority areas for conservation outside oil blocks, but their coverage was insufficient to completely represent biodiversity. Instead, priority areas that include southern oil blocks provide a higher representation of biodiversity indicators. Therefore, preserving the southern Amazon becomes essential to improve the protection of Amazonian biodiversity in Ecuador, and avoiding oil exploitation in these areas (33% of the extent of southern oil blocks) should be considered a conservation alternative. Also, it is highly recommended to improve current oil exploitation technology to reduce environmental impacts in the region, especially within five oil blocks that we identified as most valuable for the conservation of biodiversity. The application of these and other recommendations depends heavily on the Ecuadorian government, which needs to find a better balance between the use of the Amazon resources and biodiversity conservation.

Dynamic of pollutants concentration in forest stands from Copsa Mica industrial area

Directory of Open Access Journals (Sweden)

Marian Ianculescu

2009-11-01

Full Text Available The paper presents the dynamics of pollutants concentrations from nonferrous metallurgical plant in Copºa Mica, considered, between the years 1985 -1989, as the most polluted area, even in the world, and detected as a large black spot on Landsat satellite imagery.Returning to investigations in this area, after 20-25 years, the pollution activity was changed after 1990, as a consequence of the reductionof industrial capacity, including the black smoke plant decommissioning, and the chimney built for exhaust pollutants over 350 m feet high, resulted some conclusions, necessary for decisions that have to be taken by environmental, forestry, health andagriculture authorities.The litter, soil and vegetation samples were colected from the same permanent sample plots between the years 2006-2009, as between the years 1985-1989, using the same methods, in order to be compared and analyzed. Therefore, returning to investigations in these permanent sample plots, were found the following conclusions: i between the period 1985 - 1989, in all examined cases were revealed high pollutants concentrations, even exceeding the maximum allowable limit (MAL consisting of suphur compounds in synergistic action with heavy metals(Cu, Pb, Cd, Zn, Mn, etc., in vegetation and litter, which was directly correlatedwith noxious concentrations in the air, and concentrations below MAL in soil samples; ii contrary, regarding the new pollution activity, it has been revealed low noxious concentration, in vegetation, litter and soil samples collected during the period between the years 2006-2008, which are directly related to their low concentrationlevel in the air. Due to pollutants accumulation phenomenon over the years, high pollutants concentrations, ten times higher than MAL, were found in the superior soil layer. In such circumstances the best solution to protect the environment, population and livestock of the damaged area, for tens of thousands of hectares, is the closure

Evaluation of the use of polymer modified bitumen in the production of high modulus asphalt for heavily-trafficked roads

CSIR Research Space (South Africa)

Komba, Julius J

2015-05-01

Full Text Available Enrobé à Module Élevé (EME) technology, a High Modulus Asphalt (HiMA), has been introduced to South Africa to provide an optimum solution for the design and construction of heavily trafficked roads. Implementation of EME technology in South Africa...

Masterplan to safeguard Venice and to restore the lagoon and conterminous areas

Science.gov (United States)

Bini, Claudio; Gallo, Alba; Nadimi-Goki, Mandana; Wahsha, Mohammad

2015-04-01

Venice and its lagoon constitute a complex system, well known all over the world for the peculiarity of the town and for the fragility of the lagoon ecosystem with its delicate equilibrium. The whole system has been, and is currently, affected by human activities (industry, agriculture, settlements, tourism) that impact severely the ecosystem. Discharge from the agricultural drainage basin affects particularly the area North of the city of Venice; the central and southern areas, instead, receive important pollutant inputs from the industrial zone of Porto Marghera since the early'50s. Additional sources of pollution are domestic sewage and waste disposal from the urban area, that is visited by more than 10M people every year. As a consequence of the increasing land contamination, significant amounts of contaminants (both organic and inorganic) are accumulated in soils of the borderline, in water and in lagoon sediments, which constitute a potential source of secondary pollution. Results of surveys carried out in recent years in the whole area show that contaminants concentration increased from the beginning of the industrial activities until the '90s, when Porto Marghera declined. Most of contaminants have concentrations above the background levels. The highest metal levels were found in an area between Porto Marghera and the city of Venice, where both industrial and urban sewage are discharged, provoking environmental and human health hazard. In order to safeguard the city of Venice, and to restore its lagoon and conterminous areas, a Master Plan of intervention has been developed since the early 2000s. The land currently interested by environmental analysis and/or restoration covers approximately 1350ha; 78% of these (1100ha) proved variously contaminated, with 85% of sites overcoming the National Reference Values. Contamination, besides being diffused, is quite complex, involving the co-existence of several contaminant families (PAH, PCB, dioxin, heavy metals

Seawater quality assessment and identification of pollution sources along the central coastal area of Gabes Gulf (SE Tunisia): Evidence of industrial impact and implications for marine environment protection.

Science.gov (United States)

El Zrelli, Radhouan; Rabaoui, Lotfi; Ben Alaya, Mohsen; Daghbouj, Nabil; Castet, Sylvie; Besson, Philippe; Michel, Sylvain; Bejaoui, Nejla; Courjault-Radé, Pierre

2018-02-01

Temperature, pH and trace elements (F, P, Cr, Cu, Zn, Cd, and Pb) contents were determined in 16 stations as well as in 2 industrial and 2 domestic discharge sources, in the central coastal area of the Gulf of Gabes. Compared to the northern and southern areas of the study area, the highest contents of contaminants were reached in the central area which hosts the coastal industrial complex. The seawater in this central area was also found to be acid and of higher temperature. Based on the Water Pollution Index results, an increasing degradation gradient of the seawater quality was revealed from northern and/or southern stations to central ones, categorized as 'strongly to seriously affected'. Phosphogypsum wastes dumped by the Tunisian Chemical Group (GCT) seem to have continuously degraded the seawater quality in the study area. A rapid intervention is needed to stop the effects on the marine environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lead exposure of the child population in Greece.

Science.gov (United States)

Maravelias, C; Athanaselis, S; Poulos, L; Alevisopoulos, G; Ewers, U; Koutselinis, A

1994-12-18

Lead exposure of the child population was studied in three different areas in Greece: Kalamata which is a rural area of Southern Greece; Tavros, a district of Athens with a considerable industrial activity; and Lavrion, a small city near Athens where a lead-zinc mining and smelting industrial complex has existed for more than 90 years. The results were evaluated with respect to a number of individual, social and environmental variables (i.e. smelter, occupation of the father) especially those concerning the area of Lavrion which is the most heavily polluted area in Greece. The results of this study can be considered as an index for the extent of the lead pollution problem in the named areas of Greece.

How Industry 4.0 Changes Business : A Commercial Perspective

Directory of Open Access Journals (Sweden)

Ayşe Göksu Özüdoğru

2018-05-01

Full Text Available Industry is the part of an economy that manufacture components and goods which are highly automatized. This paper presents a general understanding about the Fourth Industry Revolution- Industry 4.0 approach from a commercial point of view. Firstly, the history of Industrial Revolution is explained and the roadmap to Industry 4.0 is shown. Industry components and the main understanding of Industry 4.0 is explained through the previous studies. Secondly, the most common usage, implementation areas and the challenging points are demonstrated. Commercial and industrial application examples of Industry 4.0 in different sectors and the possible implementation areas are defined based on countries and sectors. Finally, the commercial impacts of this new business model is given from the industrial and human perspectives.

Investigations of biofilms in the sewerage system of a highly contaminated industrial and mining area for the localization of heavy metal sources. Final report

International Nuclear Information System (INIS)

Cichos, C.; Singliar, U.

1993-02-01

The high heavy metal loading of the river Freiberger Mulde is largely caused by contaminations arising from the drainage area of the town of Freiberg. The diffuse input from the dewatering surface likely makes an important contribution to this pollution. The elimination of the reasons for the pollutant input into the sewerage and, thus, for the extremely high contamination of the sewage sludges requires a localization of sources and transport ways. For this purpose the method of investigation of biofilms on the sewer surface can be applied as a reliable method. For the industrial and mining area of Freiberg besides the different branches of industry especially the secondary emissions from deposits of old mining and metallurgical plants as well as from the extremely loaded surface of soil play an important role. The investigation of sewerage biofilms in the area considered have shown that the input of nickel and tin into the sewer is mainly caused by industry. Sources of zinc and copper above all are domestic wastewaters, whereas lead is originated from the surface run-off. Especially high pollutions of arsen and cadmium were found obviously arising from mining and production scraps. The results obtained should be the basis of activities for definite interruption of the pollutant input into the sewer system. They are a contribution to the restoration of the hydrographical network of Mulde/Elbe. (orig.) [de

High-resolution heavily T2-weighted magnetic resonance imaging for evaluation of the pituitary stalk in children with ectopic neurohypophysis

Energy Technology Data Exchange (ETDEWEB)

Sanharawi, Imane El; Tzarouchi, Loukia [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Cardoen, Liesbeth [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Universite Paris Diderot, Paris (France); Martinerie, Laetitia; Leger, Juliane; Carel, Jean-Claude [Universite Paris Diderot, Paris (France); Inserm U1141, DHU PROTECT, Paris (France); Hopital Robert Debre, APHP, Service d' Endocrinologie Pediatrique, Paris (France); Elmaleh-Berges, Monique [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Inserm U1141, DHU PROTECT, Paris (France); Alison, Marianne [Hopital Robert Debre, APHP, Service de Radiologie Pediatrique, Paris (France); Universite Paris Diderot, Paris (France); Inserm U1141, DHU PROTECT, Paris (France)

2017-05-15

In anterior pituitary deficiency, patients with non visible pituitary stalk have more often multiple deficiencies and persistent deficiency than patients with visible pituitary stalk. To compare the diagnostic value of a high-resolution heavily T2-weighted sequence to 1.5-mm-thick unenhanced and contrast-enhanced sagittal T1-weighted sequences to assess the presence of the pituitary stalk in children with ectopic posterior pituitary gland. We retrospectively evaluated the MRI data of 14 children diagnosed with ectopic posterior pituitary gland between 2010 and 2014. We evaluated the presence of a pituitary stalk using a sagittal high-resolution heavily T2-weighted sequence and a 1.5-mm sagittal T1-weighted turbo spin-echo sequence before and after contrast medium administration. A pituitary stalk was present on at least one of the sequences in 10 of the 14 children (71%). T2-weighted sequence depicted the pituitary stalk in all 10 children, whereas the 1.5-mm-thick T1-weighted sequence depicted 2/10 (20%) before contrast injection and 8/10 (80%) after contrast injection (P=0.007). Compared with 1.5-mm-thick contrast-enhanced T1-weighted sequences, high-resolution heavily T2-weighted sequence demonstrates better sensitivity in detecting the pituitary stalk in children with ectopic posterior pituitary gland, suggesting that contrast injection is unnecessary to assess the presence of a pituitary stalk in this setting. (orig.)

High-resolution heavily T2-weighted magnetic resonance imaging for evaluation of the pituitary stalk in children with ectopic neurohypophysis.

Science.gov (United States)

El Sanharawi, Imane; Tzarouchi, Loukia; Cardoen, Liesbeth; Martinerie, Laetitia; Leger, Juliane; Carel, Jean-Claude; Elmaleh-Berges, Monique; Alison, Marianne

2017-05-01

In anterior pituitary deficiency, patients with non visible pituitary stalk have more often multiple deficiencies and persistent deficiency than patients with visible pituitary stalk. To compare the diagnostic value of a high-resolution heavily T2-weighted sequence to 1.5-mm-thick unenhanced and contrast-enhanced sagittal T1-weighted sequences to assess the presence of the pituitary stalk in children with ectopic posterior pituitary gland. We retrospectively evaluated the MRI data of 14 children diagnosed with ectopic posterior pituitary gland between 2010 and 2014. We evaluated the presence of a pituitary stalk using a sagittal high-resolution heavily T2-weighted sequence and a 1.5-mm sagittal T1-weighted turbo spin-echo sequence before and after contrast medium administration. A pituitary stalk was present on at least one of the sequences in 10 of the 14 children (71%). T2-weighted sequence depicted the pituitary stalk in all 10 children, whereas the 1.5-mm-thick T1-weighted sequence depicted 2/10 (20%) before contrast injection and 8/10 (80%) after contrast injection (P=0.007). Compared with 1.5-mm-thick contrast-enhanced T1-weighted sequences, high-resolution heavily T2-weighted sequence demonstrates better sensitivity in detecting the pituitary stalk in children with ectopic posterior pituitary gland, suggesting that contrast injection is unnecessary to assess the presence of a pituitary stalk in this setting.

Assessment of heavy metals in sediment in a heavily polluted urban river in the Chaohu Basin, China

Science.gov (United States)

Shao, Shiguang; Xue, Lianqing; Liu, Cheng; Shang, Jingge; Wang, Zhaode; He, Xiang; Fan, Chengxin

2016-05-01

The Nanfei River (Anhui Province, China) is a severely polluted urban river that flows into Chaohu Lake. In the present study, sediments were collected from the river and analyzed for their heavy metal contents. Multivariate statistics and the fuzzy comprehensive assessment method were used to determine the sources of pollution, the current pollution status, and spatial and temporal variations in heavy metal pollution in sediments. The concentrations of arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), mercury (Hg), nickel (Ni), lead (Pb), and zinc (Zn) in sediments ranged from 5.67-113, 0.08-40.2, 41.6-524, 15.5-460, 0.03-4.84, 13.5-180, 18.8-250, and 47.9-1 996 mg/kg, and the average concentrations of each metal were 1.7, 38.7, 1.8, 5.5, 18.8, 1.3, 2.5, and 11.1 times greater than the background values, respectively. Multivariate statistical analysis demonstrated that Hg, Cu, Cr, Cd, and Ni may have originated from industrial activities, whereas As and Pb came from agricultural activities. The fuzzy comprehensive assessment method, based on the fuzzy mathematics theory, was used to obtain a detailed assessment of the sediment quality in the Nanfei River watershed. The results indicated that the pollution was moderate in the downstream tributaries of the Nianbu and Dianbu Rivers, but was severe in the main channel of the Nanfei River and in the upstream tributaries of the Sili and Banqiao Rivers. Therefore, sediments in the Nanfei River watershed are heavily polluted and urgent measures should be taken to remedy the status.

Quantitative Microstructural Characterization of Thick Aluminum Plates Heavily Deformed Using Equal Channel Angular Extrusion

DEFF Research Database (Denmark)

Mishin, Oleg; Segal, V.M.; Ferrasse, S.

2012-01-01

A detailed quantitative analysis of the microstructure has been performed in three orthogonal planes of 15-mm-thick aluminum plates heavily deformed via two equal channel angular extrusion (ECAE) routes. One route was a conventional route A with no rotation between passes. Another route involved...... sequential 90 deg rotations about the normal direction (ND) between passes. The microstructure in the center of these plates, and especially the extent of microstructural heterogeneity, has been characterized quantitatively and compared with that in bar samples extruded via either route A or route Bc with 90...... Bc. © The Minerals, Metals & Materials Society and ASM International 2012...

Features of the band structure and conduction mechanisms of n-HfNiSn heavily doped with Y

Energy Technology Data Exchange (ETDEWEB)

Romaka, V. A., E-mail: vromaka@polynet.lviv.ua [National Academy of Sciences of Ukraine, Pidstryhach Institute for Applied Problems of Mechanics and Mathematics (Ukraine); Rogl, P. [Universitet Wien, Institut für Physikalische Chemie (Austria); Romaka, V. V. [National University “Lvivska Politechnika” (Ukraine); Kaczorowski, D. [Polish Academy of Sciences, Institute of Low Temperature and Structure Research (Poland); Krayovskyy, V. Ya. [National University “Lvivska Politechnika” (Ukraine); Stadnyk, Yu. V.; Horyn, A. M. [Ivan Franko Lviv National University (Ukraine)

2017-02-15

The crystalline and electronic structures, energy, kinetic, and magnetic characteristics of n-HfNiSn semiconductor heavily doped with Y acceptor impurity are studied in the ranges: T = 80–400 K, N{sub A}{sup Y} ≈ 1.9 × 10{sup 20}–5.7 × 10{sup 21} cm{sup –3} (x = 0.01–0.30), and H ≤ 10 kG. The nature of the mechanism of structural defect generation is determined, which leads to a change in the band gap and the degree of semiconductor compensation, the essence of which is the simultaneous reduction and elimination of structural donor-type defects as a result of the displacement of ~1% of Ni atoms from the Hf (4a) site, and the generation of structural acceptor-type defects by substituting Hf atoms with Y atoms at the 4a site. The results of calculations of the electronic structure of Hf{sub 1–x}Y{sub x}NiSn are in agreement with the experimental data. The discussion is performed within the Shklovskii–Efros model of a heavily doped and compensated semiconductor.

A Solder Based Self Assembly Project in an Introductory IC Fabrication Course

Science.gov (United States)

Rao, Madhav; Lusth, John C.; Burkett, Susan L.

2015-01-01

Integrated circuit (IC) fabrication principles is an elective course in a senior undergraduate and early graduate student's curriculum. Over the years, the semiconductor industry relies heavily on students with developed expertise in the area of fabrication techniques, learned in an IC fabrication theory and laboratory course. The theory course…

Mapping of spatial and temporal variations of' water quality in an industrial area: a remote sensing and GIS approach

International Nuclear Information System (INIS)

Lakshmi, T.V.; Reddy, M.A.; Anjaneyulu, Y.

2005-01-01

This paper illustrate the impact of industrialization on water quality in and around Nakkavagu Watershed, due to unplanted industrial development. The study area falls between 78 deg. 05' - 78 deg. 25'E. longitude and 17 deg. 25'-17 deg. 45'N latitude, the catchment area extends 734 sq. km in Medak district, Andhra Predesh, India. The study area lies in the Godavari Basin. Remote sensing and GIS techniques are used to map the spatial and temporal distribution of water quality with respect to land use / land cover (Lu /Lc) changes for a period of three decades. Spatial database consisting of drainage network and geomorphology and land use / land cover change detection maps (1970-2004) have been generated for the entire watershed using remote sensing satellite data. Attribute database consisting of (water quality analysis is carried out and corresponding water quality index is calculated on a five point scale: 0- 25 Excellent, 26 -50 Good, 51 -75 Poor, 76 -100 Very poor, and> 100 Unfit for Drinking. Integrated study to establish the impact of Lu / Lc on water quality is carried out using GIS Analysis. Maps showing Lu / Lc changes and corresponding spatial distribution of water quality index were generated for the years 1979, 1989,2004. The results indicate that the water quality index in the entire Nakkavagu watershed during 1979 is excellent and good and by 2004, the entire watershed is rated in to poor, very poor and unfit for drinking. Best environmental management plans were suggested for restoration of the Nakkavagu watershed. (author)

Industrial applications and metallurgy

International Nuclear Information System (INIS)

Torres M, N.; Melendrez C, G.; Morales, F.L.

1989-01-01

From 1961 the use of nuclear energy in the industrial field in Colombia has a big advance. Today nuclear isotopes are used by private companies in this kind of application the Area of Industrial Applications and Metallurgy was the institution section that has trained and has transferred the technology needed for this purpose

Assessment Study on Sensors and Automation in the Industries of the Future. Reports on Industrial Controls, Information Processing, Automation, and Robotics

Energy Technology Data Exchange (ETDEWEB)

Bennett, Bonnie [Adventium Labs; Boddy, Mark [Adventium Labs; Doyle, Frank [Univ. of California, Santa Barbara, CA (United States); Jamshidi, Mo [Univ. of New Mexico, Albuquerque, NM (United States); Ogunnaike, Tunde [Univ. of Delaware, Newark, DE (United States)

2004-11-01

This report presents the results of an expert study to identify research opportunities for Sensors & Automation, a sub-program of the U.S. Department of Energy (DOE) Industrial Technologies Program (ITP). The research opportunities are prioritized by realizable energy savings. The study encompasses the technology areas of industrial controls, information processing, automation, and robotics. These areas have been central areas of focus of many Industries of the Future (IOF) technology roadmaps. This report identifies opportunities for energy savings as a direct result of advances in these areas and also recognizes indirect means of achieving energy savings, such as product quality improvement, productivity improvement, and reduction of recycle.

SPECIFITY OF REDEVELOPMENT OF INEFFICIENTLY USED INDUSTRIAL TERRITORIES

Directory of Open Access Journals (Sweden)

KOVALOV V. V.

2017-05-01

Full Text Available Raising of problem. In modern conditions of urban construction, the problem arises of searching for land for a new building. However, the most attractive land plots from the investment point of view are often occupied, including the industrial plants placed on them, many of which do not function. Redevelopment of industrial areas will effectively control the development of the urban environment in accordance with the requirements of the time. Purpose of the aricle. Determination of specific features of the formation of lofts as new elements of the urban environment in the redevelopment of inefficienly used industrial areas. Conclusion. When reconstructing urban degraded industrial areas, it is necessary to place residential objects in addition to commercial real estate objects, the expediency of which is confirmed by the world experience of redevelopment of industrial territories.

Trace Analysis of Heavy Metals in Ground Waters of Vijayawada Industrial Area

Science.gov (United States)

Tadiboyina, Ravisankar; Ptsrk, Prasada Rao

2016-01-01

In recent years, the new environmental problem are arising due to industrial hazard wastage, global climate change, ground water contamination and etc., gives an attention to protect environment.one of the major source of contamination of ground water is improper discharge of industrial effluents these effluents contains so many heavy metals which…

Windows of opportunities and technological innovation in the Brazilian pharmaceutical industry.

Science.gov (United States)

Tigre, Paulo Bastos; Nascimento, Caio Victor Machado França do; Costa, Laís Silveira

2016-11-03

The Brazilian pharmaceutical industry is heavily dependent on external sources of inputs, capital, and technology. However, the emergence of technological opportunities and the development of biotechnology and the decline of the patent boom and resulting advances by generic drugs have opened windows of opportunities for the local industry. The article examines the Brazilian industry's innovative behavior vis-à-vis these opportunities, showing that although the industry as a whole invests little in innovation, a few large Brazilian companies have expanded their market share and stepped up their investments in research and development, supported by public policies for innovation. Resumo: A indústria farmacêutica brasileira caracteriza-se pela grande dependência de fontes externas de insumos, capital e tecnologia. O surgimento de oportunidades tecnológicas, associadas ao desenvolvimento da biotecnologia e ao fim do boom das patentes com o consequente avanço dos medicamentos genéricos, entretanto, vem abrindo janelas de oportunidades para a indústria local. Este artigo examina o comportamento inovador da indústria brasileira à luz dessas oportunidades, revelando que, embora o conjunto da indústria mantenha baixos níveis de investimentos em inovação, um pequeno grupo de grandes empresas nacionais vem ampliando sua participação no mercado e intensificando seus investimentos em pesquisa e desenvolvimento, apoiados por políticas públicas de inovação.

Areas of improvement of tax adjustment of industrial enterprises

Directory of Open Access Journals (Sweden)

Abramova Olha

2016-03-01

Full Text Available This article summarizes the scientific approaches and practical experience in theoretical and institutional framework of fiscal management industry. The basic problems in the fiscal management system, the tax regulation methods of large taxpayers are shown. Opportunity is grounded to stimulate the enterprises activity in the directions of tax rates differentiation, tax exemptions and tax credit.

A novel assessment of odor sources using instrumental analysis combined with resident monitoring records for an industrial area in Korea

Science.gov (United States)

Lee, Hyung-Don; Jeon, Soo-Bin; Choi, Won-Joon; Lee, Sang-Sup; Lee, Min-Ho; Oh, Kwang-Joong

2013-08-01

The residents living nearby the Sa-sang industrial area (SSIA) continuously were damaged by odorous pollution since 1990s. We determined the concentrations of reduced sulfur compounds (RSCs) [hydrogen sulfide (H2S), methyl mercaptan (CH3SH), dimethyl sulfide (DMS), and dimethyl disulfide (DMDS)], nitrogenous compounds (NCs) [ammonia (NH3) and trimethylamine (TMA)], and carbonyl compounds (CCs) [acetaldehyde and butyraldehyde] by instrumental analysis in the SSIA in Busan, Korea from Jun to Nov, 2011. We determined odor intensity (OI) based on the concentrations of the odorants and resident monitoring records (RMR). The mean concentration of H2S was 10-times higher than NCs, CCs and the other RSC. The contribution from RSCs to the OI was over 50% at all sites excluding the A-5 (chemical production) site. In particular, A-4 (food production) site showed more than 8-times higher the sum of odor activity value (SOAV) than the other sites. This suggested that the A-4 site was the most malodorous area in the SSIA. From the RMR analysis, the annoyance degree (OI ≥ 2) was 51.9% in the industrial area. The 'Rotten' smell arising from the RSCs showed the highest frequency (25.3%) while 'Burned' and 'Other' were more frequent than 'Rotten' in the residential area. The correlation between odor index calculated by instrumental analysis and OI from the RMR was analyzed. The Pearson correlation coefficient (r) of the SOAV was the highest at 0.720 (P food production causes significant annoyance in the SSIA. We also confirm RMR data can be used effectively to evaluate the characteristic of odorants emitted from the SSIA.

Aerial photos for obtaining information on vegetation in areas of high population densities

Energy Technology Data Exchange (ETDEWEB)

Kenneweg, H

1975-01-01

An air pollution survey was conducted which includes a description of an inventory of Freiburg's roadside trees with the aid of infrared aerial photos, supported by a register of trees by species. Results were mapped by street averages of injury and analyses by species susceptibility and stress factors. Building and traffic density were used as stress indicators presumed to be correlated with others such as road salting or other disturbances. In a ranking based on these factors Tilia sp. was the most and Robinia pseudoacacia the least susceptible, with Aesculus, Acer, Platanus and Crataegus spp. intermediate in descending order of susceptibility. A second survey a year later showed deterioration in most parts of the town, but some improvement was observed in the central Rathausplatz, where traffic had been excluded, salting had been stopped, and certain tree amelioration measures were being tried. Other topics discussed include surveys of total green vegetation in cities and the mapping of air pollution risks near heavily industrialized areas. In a study of 1600 spruce stands near the Ruhr region, no simple correlations with topographic factors were found, though the worst damage was frequently noticed in narrow valleys and near reservoirs.

Impact of agricultural and industrial activities on ground water quality in Kasur area

International Nuclear Information System (INIS)

Tasneem, M.A.; Latif, Z.; Butt, S.; Afzal, M.; Ali, M.; Afzal, M.; Khan, I.H.; Sajjad, M.I.

1999-01-01

This paper focuses on the impact of agricultural and industrial activities on groundwater quality. Kasur area was selected to study the influence of chemical fertilizers and tannery effluents on groundwater with the help of /sup 15/N of water nitrates. Bremner and keeney methods with certain modifications ware adopted for extraction of nitrate nitrogen in the form of ammonium ions. Ammonium concentrates were converted to nitrogen gas using potassium hypo bromide solution and analyzed on GD-150 mass spectrometer. /sup 15/N of nitrates from groundwater (n=14), pond water and Kisan urea were determined. There is a pronounced difference in the /sup 15/N values of nitrates from various sources. /sup 15/N of pond water (mixture of tannery effluents, sewerage and rainwater) was found to be +31.99% and +21.26% for the first and the second samplings respectively. /sup 15/N of Kisan urea sample was determined to be - 1.00%. The nitrate concentration of groundwater ranged from 1-171 ppm and / sup 15/N was found to be -0.40 to WHO permissible limits (45 ppm). Temporal variation was also observed but the values were still above the WHO limits. It is concluded that the major source of nitrates pollution in the Kasur area is due to chemical fertilizers and +37.10%. Out of 14 drinking water samples six have nitrate contents above biological wastes but not due to the tannery effluents. (author)

Variation of solubility, biokinetics and dose coefficient of industrial uranium oxides according to the specific surface area

International Nuclear Information System (INIS)

Chazel, V.; Houpert, P.; Ansorbolo, E.; Henge-Napoli, M.H.; Paquet, F.

2000-01-01

The in vitro solubility, absorption to blood, lung retention and dose coefficient of industrial UO 2 samples were studied as a function of the specific surface area (SSA) of the particles. An in vitro study has been carried out on two samples of industrial UO 4 to compare the results with those obtained with UO 2 . Ten UO 2 samples supplied by different fuel factories or research laboratories, presented specific surface areas from 1.00 to 4.45 m 2 .g -1 . The wide range of values of SSA was due to the different conditions of fabrication. Dissolution tests in cell culture medium made on these ten samples have shown that the solubility increased 2.5-fold when the SSA increased 1.7-fold. The same tendency has been found for UO 4 , a soluble compound, and for U 3 O 8 , a moderately soluble compound. Four in vivo experiments carried out on rats by intratracheal instillation of dust suspensions of UO 2 , have highlighted the decrease in lung retention and the increase of absorption to blood with the SSA. The experimental absorption parameters calculated from the in vivo data allowed specific dose coefficients to be obtained which decreased from 6.6 to 4.3 μSv.Bq -1 when the SSA increased from 1.60 to 3.08 m 2 .g -1 . Thus, the medical monitoring of workers at the workplace has to take into account any change in the fabrication process of the uranium compound which can affect the physiochemical properties and consequently the dose coefficient. (author)

CNEN-NN 6.04 standard adaptation in Brazil for industrial radiographic work in occupied areas or public roads

International Nuclear Information System (INIS)

Teixeira, P.B.; Aquino, J.O. de; Souza, L.A. de

1996-01-01

The industrial radiographic work that uses mobile equipment in Brazil must be in compliance with the National Commission of Nuclear Energy (CNEN) Regulation CNEN-NN 6.04. It states that every works that employs radiographic equipment in occupied areas or public roads requires a specific radiation protection procedure. This procedure must be approved by the CNEN at least fifteen days before starting the job. It is not always possible to the users to get their licensing work at time, because the industrial radiography jobs need immediate actions. Furthermore, the CNEN-NN 6.04 Regulation does not specify what type of information the procedures should involve, so that some important information had been often missed, causing a delaying in the licensing procedures. The corrective and preventive actions taken by the CNEN to optimize this kind of jobs and to overcome bureaucratic difficulties are described. A standard radiation protection procedure is also presented. (authors). 2 refs., 2 tabs

Bio-effect monitoring using a [(15)N]methacetin test as diagnostic tool to monitor remediation effects in an industrially polluted region.

Science.gov (United States)

Rolle-Kampczyk, Ulrike Elisabeth; Rehwagen, Martina; Franck, Ulrich; Weiss, Holger; Krumbiegel, Peter; Herbarth, Olf

2006-04-10

The classical way to demonstrate the efficiency of remediation is measuring the reduction of toxic compounds in the environment. Nevertheless, more important is the risk reduction in human health. To determine changing health effects, exposure and bio-effects have to be monitored at time of and during remediation. Kindergarten children from a heavily polluted industrial (n=23) and a control area (n=12) were investigated. The region-specific outdoor and indoor exposure [27 volatile organic compounds (VOC), emphasis on tri- and tetrachloroethylene (TRI, TETRA)], the internal load [(trichloroacetic acid-TCA-as urine metabolites of TRI and TETRA and S-phenyl- and S-benzylmercapturic acid (SPMA and SBMA) as metabolites of benzene and toluene], and biological effect assessment ([(15)N]methacetin test-a non-invasive stable isotope test to determine the unspecific liver detoxification capacity of an individual) were measured twice a year during 2 years of remediation (1997/1998). It could be shown that in- and outdoor levels of TRI and TETRA decreased by 47% in the heavily polluted village, Greppin, while the levels remained much the same in the control village, Roitzsch. This trend was reflected in the decreasing elimination of TCA in the urine (41%) by the Greppin children, with no differences in the TCA elimination in Roitzsch probands. As the remediation efforts decreased the burden of exposure, the children's liver detoxification capacity improved as well. Combining different methods, such as exposure-effect (external and internal loads) and bio-effect monitoring, proved to be useful to assess remediation successes including the improvement in human health.

Economic potential of natural gas-fired cogeneration--analysis of Brazil's chemical industry

International Nuclear Information System (INIS)

Szklo, A.S.; Soares, J.B.; Tolmasquim, M.T.

2004-01-01

This paper attempts to estimate the technical and economic potential for natural gas-fired cogeneration (NGCHP) in Brazil's chemical industry as well as also analyses the impacts of specific incentive policies on the economic feasibility of this potential. Currently, the NGCHP installed capacity at Brazil's chemical industry is still quite a low figure, although the chemical plants are under heavy pressures to: (1) cut costs; and (2) show a rising awareness of the importance of power service quality, underscored even more heavily by Brazil's recent power crisis. According this study, a natural gas-fired remaining technical potential of 1.4 GW is noted in the Brazilian chemical industry. Financing policies showed to be the stand-alone policy that would be most successful for ensuring the economic feasibility of this technical potential. Nevertheless, this policy proved to be affected by the economic scenario under consideration, which includes world oil prices, electricity tariff and foreign exchange ratio possible paths. Consequently, the key issue is related to the ability to assess which economic scenario is rated as more probable by possible future investors in NGCHP, and then selecting the most appropriate incentive policy

Industrial applications of computer tomography

International Nuclear Information System (INIS)

Sheng Kanglong; Qiang Yujun; Yang Fujia

1992-01-01

Industrial computer tomography (CT) and its application is a rapidly developing field of high technology. CT systems have been playing important roles in nondestructive testing (NDT) of products and equipment for a number of industries. Recently, the technique has advanced into the area of industrial process control, bringing even greater benefit to mankind. The basic principles and typical structure of an industrial CT system Descriptions are given of some successful CT systems for either NDT application or process control purposes

[Thinking on development of Shanxi Astragali Radix industry].

Science.gov (United States)

Qin, Xue-Mei; Li, Ai-Ping; Li, Ke; Li, An-Ping; Ning, Lu-Hong

2016-12-01

Shanxi, a traditional production area to produce genuine Astragali Radix of high quality, has experienced major changes in the pattern of resources. This area once accounted for half of Astragali Radix industry, but now only serves as the largest supply area of traditional wild Astragali Radix. Furthermore, the strategic position of Shanxi Astragali Radix industry will become more prominent and more important to economic and social development in face of the diversity of market demands, especially for the strong demands of high-end Astragali Radix. In addition, Astragalus industry involves the simultaneous development of the first, second and tertiary industries in many areas, and it is typical and representative in the traditional Chinese medicine industry development. However, the application and industrial development of Shanxi Astragali Radix have been restricted due to the problems such as blind promotion of transplanting cultivation technology, and lack of science and technology including efficacy investigation, safety evaluation, standardization and controllability studies. Therefore, we would analyze the production history, resource structure, the current situation and progress of industry development, scientific research foundation and existing problem in this paper, and put forward countermeasures for development and technical innovation in order to make Astragali Radix industry bigger and stronger through innovation-driven and make benefits for demos. This thought provides a reference for the exploratory development of other large varieties of Chinese medicinal materials. Copyright© by the Chinese Pharmaceutical Association.

Thermal equilibrium concentration of intrinsic point defects in heavily doped silicon crystals - Theoretical study of formation energy and formation entropy in area of influence of dopant atoms-

Science.gov (United States)

Kobayashi, K.; Yamaoka, S.; Sueoka, K.; Vanhellemont, J.

2017-09-01

It is well known that p-type, neutral and n-type dopants affect the intrinsic point defect (vacancy V and self-interstitial I) behavior in single crystal Si. By the interaction with V and/or I, (1) growing Si crystals become more V- or I-rich, (2) oxygen precipitation is enhanced or retarded, and (3) dopant diffusion is enhanced or retarded, depending on the type and concentration of dopant atoms. Since these interactions affect a wide range of Si properties ranging from as-grown crystal quality to LSI performance, numerical simulations are used to predict and to control the behavior of both dopant atoms and intrinsic point defects. In most cases, the thermal equilibrium concentrations of dopant-point defect pairs are evaluated using the mass action law by taking only the binding energy of closest pair to each other into account. The impacts of dopant atoms on the formation of V and I more distant than 1st neighbor and on the change of formation entropy are usually neglected. In this study, we have evaluated the thermal equilibrium concentrations of intrinsic point defects in heavily doped Si crystals. Density functional theory (DFT) calculations were performed to obtain the formation energy (Ef) of the uncharged V and I at all sites in a 64-atom supercell around a substitutional p-type (B, Ga, In, and Tl), neutral (C, Ge, and Sn) and n-type (P, As, and Sb) dopant atom. The formation (vibration) entropies (Sf) of free I, V and I, V at 1st neighboring site from B, C, Sn, P and As atoms were also calculated with the linear response method. The dependences of the thermal equilibrium concentrations of trapped and total intrinsic point defects (sum of free I or V and I or V trapped with dopant atoms) on the concentrations of B, C, Sn, P and As in Si were obtained. Furthermore, the present evaluations well explain the experimental results of the so-called ;Voronkov criterion; in B and C doped Si, and also the observed dopant dependent void sizes in P and As doped Si

Rediscovery of an old article reporting that the area around the epicenter in Hiroshima was heavily contaminated with residual radiation, indicating that exposure doses of A-bomb survivors were largely underestimated

International Nuclear Information System (INIS)

Sutou, Shizuyo

2017-01-01

The A-bomb blast released a huge amount of energy: thermal radiation (35%), blast energy (50%), and nuclear radiation (15%). Of the 15%, 5% was initial radiation released within 30 s and 10% was residual radiation, the majority of which was fallout. Exposure doses of hibakusha (A-bomb survivors) were estimated solely on the basis of the initial radiation. The effects of the residual radiation on hibakusha have been considered controversial; some groups assert that the residual radiation was negligible, but others refute that assertion. I recently discovered a six-decade-old article written in Japanese by a medical doctor, Gensaku Obo, from Hiroshima City. This article clearly indicates that the area around the epicenter in Hiroshima was heavily contaminated with residual radiation. It reports that non-hibakusha who entered Hiroshima soon after the blast suffered from severe acute radiation sickness, including burns, external injuries, fever, diarrhea, skin bleeding, sore throat and loss of hair—as if they were real hibakusha. This means that (i) some of those who entered Hiroshima in the early days after the blast could be regarded as indirect hibakusha; (ii) ‘in-the-city-control’ people in the Life Span Study (LSS) must have been irradiated more or less from residual radiation and could not function properly as the negative control; (iii) exposure doses of hibakusha were largely underestimated; and (iv) cancer risk in the LSS was largely overestimated. Obo's article is very important to understand the health effects of A-bombs so that the essence of it is translated from Japanese to English with the permission of the publisher.

Assessment of industry needs for oil shale research and development. Final report

Energy Technology Data Exchange (ETDEWEB)

Hackworth, J.H.

1987-05-01

Thirty-one industry people were contacted to provide input on oil shale in three subject areas. The first area of discussion dealt with industry`s view of the shape of the future oil shale industry; the technology, the costs, the participants, the resources used, etc. It assessed the types and scale of the technologies that will form the industry, and how the US resource will be used. The second subject examined oil shale R&D needs and priorities and potential new areas of research. The third area of discussion sought industry comments on what they felt should be the role of the DOE (and in a larger sense the US government) in fostering activities that will lead to a future commercial US oil shale shale industry.