Combined particle emission reduction and heat recovery from combustion exhaust-A novel approach for small wood-fired appliances

International Nuclear Information System (INIS)

Messerer, A.; Schmatloch, V.; Poeschl, U.; Niessner, R.

2007-01-01

Replacing fossil fuels by renewable sources of energy is one approach to address the problem of global warming due to anthropogenic emissions of greenhouse gases. Wood combustion can help to replace fuel oil or gas. It is advisable, however, to use modern technology for combustion and exhaust gas after-treatment in order to achieve best efficiency and avoid air quality problems due to high emission levels often related to small scale wood combustion. In this study, simultaneous combustion particle deposition and heat recovery from the exhaust of two commercially available wood-fired appliances has been investigated. The experiments were performed with a miniature pipe bundle heat exchanger operating in the exhaust gas lines of a fully automated pellet burner or a closed fireplace. The system has been characterised for a wide range of aerosol inlet temperatures (135-295 deg. C) and flow velocities (0.13-1.0ms -1 ), and particle deposition efficiencies up to 95% have been achieved. Deposition was dominated by thermophoresis and diffusion and increased with the average temperature difference and retention time in the heat exchanger. The aerosols from the two different appliances exhibited different deposition characteristics, which can be attributed to enhanced deposition of the nucleation mode particles generated in the closed fire place. The measured deposition efficiencies can be described by simple linear parameterisations derived from laboratory studies. The results of this study demonstrate the feasibility of thermophoretic particle removal from biomass burning flue gas and support the development of modified heat exchanger systems with enhanced capability for simultaneous heat recovery and particle deposition

Catalytic combustion in small wood burning appliances

Energy Technology Data Exchange (ETDEWEB)

Oravainen, H [VTT Energy, Jyvaeskylae (Finland)

1997-12-31

There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

Catalytic combustion in small wood burning appliances

Energy Technology Data Exchange (ETDEWEB)

Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

1996-12-31

There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

Heat transfer in gas-cooled piles; Echanges thermiques dans les piles a gaz

Energy Technology Data Exchange (ETDEWEB)

Le Foll, J; Gelin, P; Robert, E de [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

. Technological studies led to such developments as special machining of the caps, using high conductibility metanes, anodic oxidation of thin discs. They provided the basis for solving the problem by removing the more trouble-some heat sources and providing heat insulation of the caps. Experimental study of convection around the fuel rod extremities led then to formulate specific boundary conditions of conduction inside the caps for any given geometry. Conduction in turn was studied by electrical analogy and permitted to map the temperature distribution of the critical region. (author) [French] Des mesures de coefficients d'echange locaux effectuees en regime etabli sur une gaine a ailettes longitudinales montrent que la distribution de ces coefficients le long du contour chauffant d'une section droite presente en general des singularites tres accentuees qui rendent inapplicables les calculs classiques de conduction dans les ailettes. Une etude systematique de cette distribution etablit cependant que deux coefficients numeriques calcules par integration dans le plan de section droite suffisent a rattacher les proprietes thermiques globales a celles d'un canal circulaire de contour isotherme, avec une approximation suffisante dans la plupart des cas. Bien qu'assez delicat, le calcul de ces deux coefficients est rendu accessible par deux analogies rheoelectriques et on peut meme atteindre directement l'influence d'une petite deformation du contour de gaine. Pour une valeur donnee de la temperature limite de gaine, le calcul des performances du canal entier est effectue en considerant que cette limite est effectivement atteinte dans une section droite courante. En pratique, la division du combustible en cartouches courtes risque d'introduire des singularites importantes par rapport a ce cas ideal et le probleme se pose de determiner la forme des extremites de cartouches pour eviter que ces singularites n'affectent les performances. Or, les bouchons qui assurent la fermeture des

Transforce lingual appliances pre-adjusted invisible appliances simplify treatment.

Science.gov (United States)

Clark, William John

2011-01-01

Transforce lingual appliances are designed to be used in conjunction with conventional fixed appliances. Lingual arch development is normally followed by bonded fixed appliances to detail the occlusion. Alternatively Transforce appliance treatment is an efficient method of preparing complex malocclusions prior to a finishing stage with invisible appliances. This approach is ideal for adult treatment, using light continuous forces for arch development with appliances that are comfortable to wear. Sagittal and Transverse appliances are designed for arch development in a range of sizes for contracted arches. They can be used to treat all classes of malocclusion and are pre-adjusted fixed/removable devices for non-compliance treatment. Force modules with nickel titanium coil springs enclosed in a tube deliver a gentle, biocompatible continuous force with a long range of action. They are excellent for mixed dentition and ideal for adult arch development. There are multiple sizes for upper and lower arch development and a sizing chart may be placed over a study model for correct selection, eliminating the need for laboratory work.

The greenhouse advantage of natural gas appliances

International Nuclear Information System (INIS)

Coombe, N.

2000-01-01

The life cycle report prepared recently by Energetics for the AGA, Assessment of Greenhouse Gas Emissions from Natural Gas, demonstrates clearly the greenhouse advantage natural gas has over coal in generating electricity. This study also goes one step further in applying this life cycle approach to the use of space and water heating within the home. The study shows the significant green-house advantage that natural gas appliances have over electric appliances. Findings from other studies also support this claim. The natural gas suppliers are encouraged to take advantage of the marketing opportunity that these studies provide, offering the householders the fuel that will significantly reduce their contribution to greenhouse emission

CE-mark for gas appliances: A laugh or a tear?

International Nuclear Information System (INIS)

Timmers, H.

1993-01-01

The title CE-mark is a quality mark for products, assigned by the European Community (EC). One and a half year ago the EC Gas Appliances Directive (GAD) came into force. According to the program 'Europe 1992' the European internal market should have been established by now. In this article the state of the art for gas appliances is given. Attention is paid to the systematics of European verification, the GAD contents, the consequences of a number of other Directives (for low-voltage materials, for electromagnetic compatibility, for efficiencies of central heating boilers, for machines, and for building products), which also affect the use of gas appliances, GASTEC's role as Notified Body, and experiences gained from European certification up to now. 6 ills., 3 tabs

The Next Generation of Appliances: Visions for Sustainability

DEFF Research Database (Denmark)

Nørgaard, Jørgen; Guldbrandsen, Tom

1998-01-01

to consume no more than 50 kWh per year, without using any risky synthetic gasses. Washing appliances will use no electricity for heating, which will bring annual electricity consumption below 50 kWh for a washing machine. For electronic equipment, the efficiency gain known from battery operated version...

Investigation of transient behaviour of combi boiler type appliances for domestic hot water

International Nuclear Information System (INIS)

Atmaca, Ayşe Uğurcan; Erek, Aytunç; Altay, Hürrem Murat

2015-01-01

Combi boiler type appliances heating both space and water demanded for use and consuming natural gas as the energy source are one of the most common branches of the household goods. This study touches mainly on two types of combi boiler concepts to investigate only domestic hot water (DHW) heating function since highly efficient condensing appliances have been manufactured in terms of space heating. First concept has the normal working configuration of the heat exchangers of a standard combi boiler; whereas, the second has the opposite operation order of the heat exchangers. 1D transient energy equations have been constructed with the help of the laws of thermodynamics in order to model the heat exchangers in a standard combi boiler. After obtaining a general mathematical model for the standard combi boiler, the energy equations have been discretised with finite difference scheme, and solved numerically in Matlab ® . Subsequently, numerical results are validated experimentally in different working modes of a standard appliance. As the last step, similar results are obtained for the second proposed concept using the related equations of the standard combi model to compare both concepts on a numerical basis. - Highlights: • 1D theoretical model of a combi boiler was constructed and verified experimentally. • Preliminary estimations will be obtained from the model about the laboratory tests. • Number of the laboratory tests will be decreased thanks to the theoretical model. • The model was used to compare the transient behaviour of two kinds of combi boilers. • The second combi boiler alternative to standard one has a higher comfort potential

Hybrid RANS/LES of flow and heat transfer in round impinging jets

International Nuclear Information System (INIS)

Kubacki, Slawomir; Dick, Erik

2011-01-01

Fluid flow and convective heat transfer predictions are presented of round impinging jets for several combinations of nozzle-plate distances H/D = 2, 6 and 13.5 (where D is the nozzle diameter) and Reynolds numbers Re = 5000, 23,000 and 70,000 with the newest version of the k-ω model of and three hybrid RANS/LES models. In the RANS mode of the hybrid RANS/LES models, the k-ω model is recovered. Three formulations are considered to activate the LES mode. The first model is similar to the hybrid models of and . The turbulent length scale is replaced by the grid size in the destruction term of the k-equation and in the definition of the RANS eddy viscosity. As grid size, a maximum measure of the hexahedral grid cell is used. The second model has the same k-equation, but the eddy viscosity is the minimum of the k-ω eddy viscosity and the Smagorinsky eddy viscosity, following a proposal by . The Smagorinsky eddy viscosity is formed with the cube root of the cell volume. The third model has, again, the same k-equation, but has an eddy viscosity which is an intermediate between the eddy viscosities of the first and second models. This is reached by using the cube root of the cell volume in the eddy viscosity formula of the first model. The simulation results are compared with experimental data for the high Reynolds number cases Re = 23,000 and Re = 70,000 and LES data for the low-Reynolds number case Re = 5000. The Reynolds numbers are defined with the nozzle diameter and the bulk velocity at nozzle outlet. At low nozzle-plate distance (the impingement plate is in the core of the jet), turbulent kinetic energy is overpredicted by RANS in the stagnation flow region. This leads to overprediction of the heat transfer rate along the impingement plate in the impact zone. At high nozzle-plate distance (the impingement plate is in the mixed-out region of the jet), the turbulence mixing is underpredicted by RANS in the shear layer of the jet which gives a too high length of

Assessment of perceived orthodontic appliance attractiveness.

Science.gov (United States)

Ziuchkovski, James P; Fields, Henry W; Johnston, William M; Lindsey, Delwin T

2008-04-01

To date, no studies have been published in the literature evaluating the esthetics of orthodontic appliances. The purpose of this study was to assess appliance variables, including appliance type, brand, wire, and ligature tie, for their relative attractiveness. Demographic factors were also evaluated. Appliances were placed in an adult, and digital images were captured, standardized, and incorporated into a computer-based survey. Subjects (n = 200) rated each image for attractiveness on a visual analog scale. The attractiveness ratings were analyzed by using factorial analysis of variance with repeated measures. Post-hoc testing was done with the Tukey-Kramer test (overall a appliances), ceramic, and all self-ligating/stainless steel appliances. No differences between brands in each appliance type were found. Ratings of some ceramic appliances were significantly affected by archwire and ligature tie, depending on several demographic interactions. Orthodontic appliance attractiveness varies by the following hierarchy of appliance types: alternative > ceramic > all stainless steel/self-ligating. Wire and tie selection can affect the appearance of ceramic appliances but have no impact on stainless steel or self-ligating appliances. Certain demographic factors have variable effects on attractiveness ratings.

A segmented appliance for space closure followed by Invisalign and fixed appliances.

Science.gov (United States)

Uribe, Flavio; Cutrera, Alice; Nanda, Ravinda

2011-01-01

This case report describes the use of a segmented appliance for space closure prior to using Invisalign. The maxillary right canine was retracted into the extracted first premolar space with a sectional wire from the first molar to the canine with no visible brackets in the incisor region. The advantage of this technique is the ability to achieve better root and rotational control during space closure with a fixed appliance that also has limited visibility. A maxillary fixed appliance was used to refine the esthetics in the maxillary arch due to the limitations of the Invisalign appliance in achieving rotational and vertical movements.

Rational gas consumption resulting from technological innovations and improved gas appliances

Energy Technology Data Exchange (ETDEWEB)

Doering, H

1980-07-01

Ruhrgas AG has developed several new or improved appliances with a view toward conserving energy. Its household heat center (see also Gas Abstr. 36, 80-1144f) uses a single core unit to supply heat for all the major heat requirements in the house, from cooking and dishwashing to water heating, space heating, and laundry washing/drying. A new burner that can function at both full and partial load with an air ratio of about 1.35 offers economical, yet quiet operation. Ruhrgas is also continuing its laboratory and field research into the application of gas-fired compression-type heat pumps.

46 CFR 111.77-3 - Appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances. 111.77-3 Section 111.77-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Appliances and Appliance Circuits § 111.77-3 Appliances. All electrical appliances, including, but...

Evaluation of advanced technologies for residential appliances and residential and commercial lighting

Energy Technology Data Exchange (ETDEWEB)

Turiel, I.; Atkinson, B.; Boghosian, S.; Chan, P.; Jennings, J.; Lutz, J.; McMahon, J.; Rosenquist, G.

1995-01-01

Section 127 of the Energy Policy Act requires that the Department of Energy (DOE) prepare a report to Congress on the potential for the development and commercialization of appliances that substantially exceed the present federal or state efficiency standards. Candidate high-efficiency appliances must meet several criteria including: the potential exists for substantial improvement (beyond the minimum established in law) of the appliance`s energy efficiency; electric, water, or gas utilities are prepared to support and promote the commercialization of such appliances; manufacturers are unlikely to undertake development and commercialization of such appliances on their own, or development and production would be substantially accelerated by support to manufacturers. This report describes options to improve the efficiency of residential appliances, including water heaters, clothes washers and dryers, refrigerator/freezers, dishwashers, space heating and cooling devices, as well as residential and commercial lighting products. Data from this report (particularly Appendix 1)were used to prepare the report to Congress mentioned previously. For the residential sector, national energy savings are calculated using the LBL Residential Energy Model. This model projects the number of households and appliance saturations over time. First, end-use consumption is calculated for a base case where models that only meet the standard replace existing models as these reach the end of their lifetime. Second, models with efficiencies equal to the technology under consideration replace existing models that reach the end of their lifetime. For the commercial sector, the COMMEND model was utilized to project national energy savings from new technologies. In this report, energy savings are shown for the period 1988 to 2015.

Poster Abstract: A Practical Model for Human-Smart Appliances Interaction

DEFF Research Database (Denmark)

Fürst, Jonathan; Fruergaard, Andreas; Johannesen, Marco Høvinghof

2016-01-01

for human-smart appliance interaction. We present a prototype implementation with an off-the-shelf smart lighting and heating system in a shared office space. Our approach minimizes the need for location metadata. It relies on a human-feedback loop (both sensor based and manual) to identify the optimal...

Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

Science.gov (United States)

Carvalho, F R; Lentini-Oliveira, D; Machado, M A C; Prado, G F; Prado, L B F; Saconato, H

2007-04-18

Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adenotonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they change the mandible posture forwards and potentially enlarge the upper airway and increase the upper airspace, improving the respiratory function. To assess the effectiveness of oral appliances or functional orthopaedic appliances for OSAS in children. A sensitive search was developed for the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2005, Issue 3); PubMed (January 1966 to September 2005); EMBASE (1980 to September 2005); Lilacs (1982 to September 2005); BBO-Bibliografia Brasileira de Odontologia (1986 to September 2005); and SciELO (1997 to September 2005). There was no restriction of language or source of information. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiologic function, behavioural problems, drop outs and withdrawals, quality of life, side effects (tolerability), economic evaluation. Data were independently extracted by two review authors. Authors were contacted for additional information. Risk ratios with 95% confidence intervals were calculated for all important dichotomous outcomes. The initial search identified 384 trials

European Gas Appliances Directive and the Dutch Decree on Gas Appliances. Special section

International Nuclear Information System (INIS)

De Bruin, B.; Venhorst, T.; Van Tricht, A.

1998-01-01

The Gas Appliances Decree is the Dutch translation of the European Gas Appliances Directive. The Decree and the EU Directive contain substantial information, provided they will be read carefully. The EU Directive lays down general safety requirements for gas appliances. They serve as a practical tool for manufacturers and service engineers. In two articles, the Directive is explained, addressing uncertainties and answering important questions. 5 ills

DNS, LES and RANS of turbulent heat transfer in boundary layer with suddenly changing wall thermal conditions

International Nuclear Information System (INIS)

Hattori, Hirofumi; Yamada, Shohei; Tanaka, Masahiro; Houra, Tomoya; Nagano, Yasutaka

2013-01-01

Highlights: • We study the turbulent boundary layer with heat transfer by DNS. • Turbulent boundary layers with suddenly changing wall thermal conditions are observed. • The detailed turbulent statistics and structures in turbulent thermal boundary layer are discussed. • Turbulence models in LES and RANS are evaluated using DNS results. • LES and RANS are almost in good agreement with DNS results. -- Abstract: The objectives of this study are to investigate a thermal field in a turbulent boundary layer with suddenly changing wall thermal conditions by means of direct numerical simulation (DNS), and to evaluate predictions of a turbulence model in such a thermal field, in which DNS of spatially developing boundary layers with heat transfer can be conducted using the generation of turbulent inflow data as a method. In this study, two types of wall thermal condition are investigated using DNS and predicted by large eddy simulation (LES) and Reynolds-averaged Navier–Stokes equation simulation (RANS). In the first case, the velocity boundary layer only develops in the entrance of simulation, and the flat plate is heated from the halfway point, i.e., the adiabatic wall condition is adopted in the entrance, and the entrance region of thermal field in turbulence is simulated. Then, the thermal boundary layer develops along a constant temperature wall followed by adiabatic wall. In the second case, velocity and thermal boundary layers simultaneously develop, and the wall thermal condition is changed from a constant temperature to an adiabatic wall in the downstream region. DNS results clearly show the statistics and structure of turbulent heat transfer in a constant temperature wall followed by an adiabatic wall. In the first case, the entrance region of thermal field in turbulence can be also observed. Thus, both the development and the entrance regions in thermal fields can be explored, and the effects upstream of the thermal field on the adiabatic region are

Motor-pump unit provided with a lifting appliance of the motor

International Nuclear Information System (INIS)

Veronesi, Luciano; Francis, W.R.

1978-01-01

This invention relates to lifting appliances and particularly concerns a 'pump and motor set' or motor-pump unit fitted with a lifting appliance enabling the motor to be separated from the pump. In nuclear power stations the reactor discharges heat that is carried by the coolant to a distant point away from the reactor to generate steam and electricity conventionally. In order to cause the reactor coolant to flow through the system, coolant motor-pump units are provided in the cooling system. These units are generally of the vertical type with an electric motor fitted vertically on the pump by means of a cylindrical or conical structure called motor support [fr

24 CFR 3280.709 - Installation of appliances.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Installation of appliances. 3280... Fuel Burning Systems § 3280.709 Installation of appliances. (a) The installation of each appliance... the manufacturer's instructions attached to the appliance. Every appliance shall be secured in place...

Optimal joint scheduling of electrical and thermal appliances in a smart home environment

International Nuclear Information System (INIS)

Shirazi, Elham; Zakariazadeh, Alireza; Jadid, Shahram

2015-01-01

Highlights: • Thermal appliances are scheduled based on desired temperature and energy prices. • A discomfort index has been introduced within the home energy scheduling model. • Appliances are scheduled based on activity probability and desired options. • Starting probability depends on the social random factor and consumption behavior. - Abstract: With the development of home area network, residents have the opportunity to schedule their power usage in the home by themselves aiming at reducing electricity expenses. Moreover, as renewable energy sources are deployed in home, a home energy management system needs to consider both energy consumption and generation simultaneously to minimize the energy cost. In this paper, a smart home energy management model has been presented in which electrical and thermal appliances are jointly scheduled. The proposed method aims at minimizing the electricity cost of a residential customer by scheduling various type of appliances considering the residents consumption behavior, seasonal probability, social random factor, discomfort index and appliances starting probability functions. In this model, the home central controller receives the electricity price information, environmental factors data as well as the resident desired options in order to optimally schedule appliances including electrical and thermal. The scheduling approach is tested on a typical home including variety of home appliances, a small wind turbine, photovoltaic panel, combined heat and power unit, boiler and electrical and thermal storages over a 24-h period. The results show that the scheduling of different appliances can be reached simultaneously by using the proposed formulation. Moreover, simulation results evidenced that the proposed home energy management model exhibits a lower cost and, therefore, is more economical.

Energy Savings Potential and RD&D Opportunities for Commercial Building Appliances (2015 Update)

Energy Technology Data Exchange (ETDEWEB)

Goetzler, William [Navigant Consulting, Burlington, MA (United States); Guernsey, Matt [Navigant Consulting, Burlington, MA (United States); Foley, Kevin [Navigant Consulting, Burlington, MA (United States); Young, Jim [Navigant Consulting, Burlington, MA (United States); Chung, Greg [Navigant Consulting, Burlington, MA (United States)

2016-06-01

The Department of Energy commissioned a technology characterization and assessment of appliances used in commercial buildings for cooking, cleaning, water heating, and other end-uses. The primary objectives of this study were to document the energy consumed by commercial appliances and identify research, development, and demonstration opportunities to improve energy efficiency in each end-use. This report serves as an update to a 2009 report of the same name by incorporating updated data and sources where possible and updating the available technology options that provide opportunities for efficiency improvements.

Domestic appliances energy optimization with model predictive control

International Nuclear Information System (INIS)

Rodrigues, E.M.G.; Godina, R.; Pouresmaeil, E.; Ferreira, J.R.; Catalão, J.P.S.

2017-01-01

Highlights: • An alternative power management control for home appliances that require thermal regulation is presented. • A Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat. • Problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. • A modulation scheme of a two-level Model Predictive Control signal as an interface block is presented. • The implementation costs in home appliances with thermal regulation requirements are reduced. - Abstract: A vital element in making a sustainable world is correctly managing the energy in the domestic sector. Thus, this sector evidently stands as a key one for to be addressed in terms of climate change goals. Increasingly, people are aware of electricity savings by turning off the equipment that is not been used, or connect electrical loads just outside the on-peak hours. However, these few efforts are not enough to reduce the global energy consumption, which is increasing. Much of the reduction was due to technological improvements, however with the advancing of the years new types of control arise. Domestic appliances with the purpose of heating and cooling rely on thermostatic regulation technique. The study in this paper is focused on the subject of an alternative power management control for home appliances that require thermal regulation. In this paper a Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat with the aim of minimizing the cooling energy consumption through the minimization of the energy cost while satisfying the adequate temperature range for the human comfort. In addition, the Model Predictive Control problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. For this purpose, the typical consumption of a 24 h period of a summer day was simulated a three-level tariff scheme was used. The new

Metal release from simulated fixed orthodontic appliances.

Science.gov (United States)

Hwang, C J; Shin, J S; Cha, J Y

2001-10-01

Most orthodontic appliances and archwires are stainless steel or nickel-titanium (NiTi) alloys that can release metal ions, with saliva as the medium. To measure metal released from the fixed orthodontic appliances currently in use, we fabricated simulated fixed orthodontic appliances that corresponded to half of the maxillary arch and soaked them in 50 mL of artificial saliva (pH 6.75 +/- 0.15, 37 degrees C) for 3 months. We used brackets, tubes, and bands made by Tomy (Tokyo, Japan). Four groups were established according to the appliance manufacturer and the type of metal in the .016 x .022-in archwires. Groups A and B were stainless steel archwires from Ormco (Glendora, Calif) and Dentaurum (Ispringen, Germany), respectively, and groups C and D were both NiTi archwires with Ormco's copper NiTi and Tomy's Bioforce sentalloy, respectively. Stainless steel archwires were heat treated in an electric furnace at 500 degrees C for 1 minute and quenched in water. We measured the amount of metal released from each group by immersion time. Our conclusions were as follows: (1) there was no increase in the amount of chromium released after 4 weeks in group A, 2 weeks in group B, 3 weeks in group C, and 8 weeks in group D; (2) there was no increase in the amount of nickel released after 2 weeks in group A, 3 days in group B, 7 days in group C, and 3 weeks in group D; and (3) there was no increase in the amount of iron released after 2 weeks in group A, 3 days in group B, and 1 day in groups C and D. In our 3-month-long investigation, we saw a decrease in metal released as immersion time increased.

Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air

Energy Technology Data Exchange (ETDEWEB)

Brand, L.

2014-04-01

This measure guideline covers how to assess and carry out the combustion safety procedures for appliances and heating equipment that uses indoor air for combustion in low-rise residential buildings. Only appliances installed in the living space, or in an area freely communicating with the living space, vented alone or in tandem with another appliance are considered here. A separate measure guideline addresses combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage that use outdoor air for combustion. This document is for inspectors, auditors, and technicians working in homes where energy upgrades are being conducted whether or not air infiltration control is included in the package of measures being applied. In the indoor combustion air case, guidelines summarized here are based on language provided in several of the codes to establish minimum requirements for the space using simplified prescriptive measures. In addition, building performance testing procedures are provided by testing agencies. The codes in combination with the test procedures offer comprehensive combustion safety coverage to address safety concerns, allowing inexperienced residential energy retrofit inspectors to effectively address combustion safety issues and allow energy retrofits to proceed.

Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

Science.gov (United States)

Carvalho, Fernando R; Lentini-Oliveira, Débora A; Prado, Lucila Bf; Prado, Gilmar F; Carvalho, Luciane Bc

2016-10-05

Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adeno-tonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbidities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they hold the lower jaw (mandible) forwards which potentially enlarges the upper airway and increases the upper airspace, improving the respiratory function. To assess the effects of oral appliances or functional orthopaedic appliances for obstructive sleep apnoea in children. We searched the following electronic databases: Cochrane Oral Health's Trials Register (to 7 April 2016); Cochrane Central Register of Controlled Trials (CENTRAL; 2016, Issue 3) in the Cochrane Library (searched 7 April 2016); MEDLINE Ovid (1946 to 7 April 2016); Embase Ovid (1980 to 7 April 2016); LILACS BIREME (from 1982 to 7 April 2016); BBO BIREME (from 1986 to 7 April 2016) and SciELO Web of Science (from 1997 to 7 April 2016). We searched ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform for ongoing trials on 7 April 2016. We placed no restrictions on the language or date of publication when searching the electronic databases. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiological function, behavioural problems, quality of life, side effects

Waste heat utilization in the thermal spa of Lavey-les-Bains

International Nuclear Information System (INIS)

2004-01-01

This final report for the Swiss Federal Office of Energy looks at the possibilities for improved waste water utilization in the Lavey-les-Bains thermal spa, Switzerland. According to the regulations in force, the temperature of the waste water rejected into the Rhone river shall not exceed 30 o C, what is currently not the case. Also the operational cost shall be reduced and the waste water quality improved. The installations are presented. From the two geothermal wells, mineral water comes out at an average flow rate of 940 l/min and a temperature of 63 o C. Actual waste water data are reported. The measured thermal water consumption data, including seasonal variations, are analysed by computerized simulation and measures to reduce the consumed volume by the optimization of internal procedures are evaluated. Measures to reduce the quantity of the rejected free chlorine are discussed. Several possible adaptations of the existing space heating, domestic water heating and pools' heating are evaluated, including cost. In addition, extensions of the thermal spa center to recreational activities are discussed, as the construction of a tropical greenhouse is

24 CFR 3280.807 - Fixtures and appliances.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically listed...

Cephalometric effects of the Jones Jig appliance followed by fixed appliances in Class II malocclusion treatment.

Science.gov (United States)

Patel, Mayara Paim; Henriques, José Fernando Castanha; Freitas, Karina Maria Salvatore; Grec, Roberto Henrique da Costa

2014-01-01

The aim of this study was to cephalometrically assess the skeletal and dentoalveolar effects of Class II malocclusion treatment performed with the Jones Jig appliance followed by fixed appliances. The sample comprised 25 patients with Class II malocclusion treated with the Jones Jig appliance followed by fixed appliances, at a mean initial age of 12.90 years old. The mean time of the entire orthodontic treatment was 3.89 years. The distalization phase lasted for 0.85 years, after which the fixed appliance was used for 3.04 years. Cephalograms were used at initial (T1), post-distalization (T2) and final phases of treatment (T3). For intragroup comparison of the three phases evaluated, dependent ANOVA and Tukey tests were used. Jones Jig appliance did not interfere in the maxillary and mandibular component and did not change maxillomandibular relationship. Jones Jig appliance promoted distalization of first molars with anchorage loss, mesialization and significant extrusion of first and second premolars, as well as a significant increase in anterior face height at the end of treatment. The majority of adverse effects that occur during intraoral distalization are subsequently corrected during corrective mechanics. Buccal inclination and protrusion of mandibular incisors were identified. By the end of treatment, correction of overjet and overbite was observed. Jones Jig appliance promoted distalization of first molars with anchorage loss represented by significant mesial movement and extrusion of first and second premolars, in addition to a significant increase in anterior face height.

49 CFR 173.219 - Life-saving appliances.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

Effects of mandibular protraction appliance associated to fixed appliance in adults

Directory of Open Access Journals (Sweden)

Bruno D'Aurea Furquim

2013-10-01

Full Text Available OBJECTIVE: This retrospective study aimed to conduct a cephalometric evaluation of the skeletal, dental and soft tissue effects resulting from treatment of adult patients presenting Class II malocclusion, performed with a Mandibular Protraction Appliance (MPA combined with a fixed orthodontic appliance. METHODS: The sample consisted of teleradiographs obtained before and after treatment of 9 adult patients (initial mean age of 22.48 years with bilateral Class II, division 1, malocclusion. Paired t test (p < 0.05 was applied to compare initial and final values. RESULTS: t test revealed an increase in anteroinferior facial height and posterior facial height. The dental changes include: extrusion of upper incisors, buccal inclination, protrusion of lower incisors, mesialization and extrusion of mandibular molars. Regarding the soft tissue component, there was an increase in nasolabial angle in addition to upper lip retrusion. CONCLUSIONS: The effects of treating Class II malocclusion adult patients, by means of using Mandibular Protraction Appliance (MPA combined with a fixed appliance were mostly observed in the mandibular arch, and consisted of buccal inclination, protrusion and intrusion of incisors, and mesialization and extrusion of the molars.

Microwave processing heats up

Science.gov (United States)

Microwaves are a common appliance in many households. In the United States microwave heating is the third most popular domestic heating method food foods. Microwave heating is also a commercial food processing technology that has been applied for cooking, drying, and tempering foods. It's use in ...

Appliance based control for Home Power Management Systems

International Nuclear Information System (INIS)

Özkan, Hanife Apaydın

2016-01-01

This study scrutinizes energy-friendly smart home appliances (hereafter ‘smart appliances’), control of these appliances and their effects on the efficient use of energy. To accomplish this, smart appliances and their operation principles are introduced and their energy savings compared to conventional appliances are analyzed using precise measurements. Then, a real-time Appliance-based Home Power Management System (Ab-HPMS) which manages power consumption of smart appliances and that of the house as a whole is proposed. For Ab-HPMS, an appliance control algorithm, called Appliance-based Rolling Wave Planning (Ab-RWP), is developed with the aim of reducing electricity cost and improving energy efficiency while maintaining user comfort. Ab-RWP algorithm interacts with appliances in a priority order based on user comfort which is determined by utilizing their smart operational characteristics. Operations of smart appliances and their integrations with Ab-HPMS are modeled with Petri nets to verify that they meet the requirements expressed in the specifications. Simulation results demonstrate that proposed Ab-HPMS provides improvements in terms of the energy consumption reduction of about 5%–16%, cost reduction of about 10%–24% and peak reduction at high demand period of about 38%–53% compared to conventional appliances usage. - Highlights: • The effects of smart home appliances on energy saving are investigated. • Petri nets models of smart appliances are developed to simulate their operations in smart home. • A real-time appliance-based home power management system (Ab-HPMS) is proposed. • Power density function is evaluated to interrupt the operation of smart washing machine.

24 CFR 3285.503 - Optional appliances.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Optional appliances. 3285.503... appliances. (a) Comfort cooling systems. When not provided and installed by the home manufacturer, any comfort cooling systems that are installed must be installed according to the appliance manufacturer's...

Magnetic fields from electric toothbrushes promote corrosion in orthodontic stainless steel appliances but not in titanium appliances.

Science.gov (United States)

Kameda, Takashi; Ohkuma, Kazuo; Oda, Hirotake; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

2013-01-01

Electric toothbrushes are widely used, and their electric motors have been reported to produce low-frequency electromagnetic fields that induced electric currents in metallic objects worn by the users. In this study, we showed that electric toothbrushes generated low-frequency magnetic fields (MFs) and induced electric currents in orthodontic appliances in artificial saliva (AS), which accelerated corrosion in stainless steel (SUS) appliances, but not in titanium (Ti) appliances; the corrosion was evaluated by using an inductively coupled plasma-optical emission spectrometer and a three-dimensional laser confocal microscope. The pH of AS used for appliance immersion did not change during or after MF exposure. These results suggested that MF-induced currents from electric toothbrushes could erode SUS appliances, but not Ti appliances, because of their high corrosion potentials. Further studies are required to clarify the mechanisms of metallic corrosion by induced currents in dental fields, which may trigger metal allergies in patients.

Compliance with removable orthodontic appliances.

Science.gov (United States)

Shah, Nirmal

2017-12-22

Data sourcesMedline via OVID, PubMed, Cochrane Central Register of Controlled Trials, Web of Science Core Collection, LILACS and BBO databases. Unpublished clinical trials accessed using ClinicalTrials.gov, National Research Register, ProQuest Dissertation and Thesis database.Study selectionTwo authors searched studies from inception until May 2016 without language restrictions. Quantitative and qualitative studies incorporating objective data on compliance with removable appliances, barriers to appliance wear compliance, and interventions to improve compliance were included.Data extraction and synthesisQuality of research was assessed using the Cochrane Collaboration's risk of bias tool, the risk of bias in non-randomised studies of interventions (ROBINS-I), and the mixed methods appraisal tool. Statistical heterogeneity was investigated by examining a graphic display of the estimated compliance levels in conjunction with 95% confidence intervals and quantified using the I-squared statistic. A weighted estimate of objective compliance levels for different appliances in relation to stipulated wear and self-reported levels was also calculated. Risk of publication bias was assessed using funnel plots. Meta-regression was undertaken to assess the relative effects of appliance type on compliance levels.ResultsTwenty-four studies met the inclusion criteria. Of these, 11 were included in the quantitative synthesis. The mean duration of objectively measured wear was considerably lower than stipulated wear time amongst all appliances. Headgear had the greatest discrepancy (5.81 hours, 95% confidence interval, 4.98, 6.64). Self-reported wear time was consistently higher than objectively measured wear time amongst all appliances. Headgear had the greatest discrepancy (5.02 hours, 95% confidence interval, 3.64, 6.40). Two studies found an increase in compliance with headgear and Hawley retainers when patients were aware of monitoring. Five studies found younger age groups to

Multi-kanban mechanism for appliance disassembly

Science.gov (United States)

Udomsawat, Gun; Gupta, Surendra M.

2005-11-01

The use of household appliances continues to rise every year. A significant number of End-Of-Life (EOL) appliances are generated because of the introduction of newer models that are more attractive, efficient and affordable. Others are, of course, generated when they become non-functional. Many regulations encourage recycling of EOL appliances to reduce the amount of waste sent to landfills. In addition, EOL appliances offer the appliance manufacturing and remanufacturing industries a source of less expensive raw materials and components. For this reason product recovery has become a subject of interest during the past decade. In this paper, we study the disassembly line for appliance disassembly. We discuss and incorporate some of the complications that are inherent in disassembly line including product arrival, demand arrival, inventory fluctuation and production control mechanisms. We show how to overcome such complications by implementing a multi-kanban system in the appliance disassembly line setting. The multi-kanban system (MKS) relies on dynamic routing of kanbans according to the state of the system. We investigate the multi-kanban mechanism using simulation and explore the effect of product mix on performance of the traditional push system (TPS) and MKS in terms of controlling the system's inventory while attempting to achieve a decent customer service level.

49 CFR 238.429 - Safety appliances.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances. 238.429 Section 238.429... Equipment § 238.429 Safety appliances. (a) Couplers. (1) The leading and the trailing ends of a semi... appliance mechanical strength and fasteners. (1) All handrails, handholds, and sill steps shall be made of 1...

Minat Masyarakat dalam Menggunakan Smart Appliances

Directory of Open Access Journals (Sweden)

Diah Yuniarti

2014-09-01

Full Text Available Harga sumber energi yang semakin naik dari tahun ke tahun dan kemajuan teknologi telah mendorong perkembangan smart grid. Smart appliance merupakan salah satu komponen penting dalam smart grid. Penerapan smart appliance sejalan dengan kebijakan untuk mengurangi konsumsi energi, mengurangi emisi karbon dan penyediaan energi dari energi terbarukan. Penetrasi telepon bergerak turut memudahkan manajemen energi dan otomatisasi home appliance. Penelitian ini dilakukan untuk menganalisis minat masyarakat, yang merupakan aktor aktif dalam konsumsi dan manajemen energi di rumah tangga. Data penelitian dianalisis  dengan menggunakan metode structural equation modeling (SEM Hasil penelitian menunjukkan bahwa variabel enjoyment memiliki pengaruh yang signifikan terhadap minat dalam menggunakan smart appliance. Sedangkan, variabel compatibility ease of use, relative advantage dan image tidak memiliki pengaruh yang signifikan terhadap minat menggunakan smart appliance.

Conjugate heat transfer LES of thermal mixing in a T-junction

Energy Technology Data Exchange (ETDEWEB)

Timperi, Antti, E-mail: antti.timperi@vtt.fi

2014-07-01

Highlights: • Turbulent mixing of hot and cold water in a T-junction is studied with LES including conjugate heat transfer. • The numerical simulations are in good agreement with experimental data in the bulk of the flow. • Comparison of different inlet and wall boundary conditions shows significant differences only near walls. • Effects of mesh and flow velocity on the velocity and temperature fluctuations are also considered. - Abstract: Turbulent mixing of hot and cold fluids may lead to high-cycle thermal fatigue in piping of nuclear power plants. In this work, the mixing in a T-junction experiment is studied by large-eddy simulation (LES). Conjugate heat transfer (CHT) between fluid and pipe wall is studied by replacing the plexiglass pipe of the experiment with a steel one. Different inlet and wall boundary conditions are first considered. Steady and turbulent inlets are compared, as well as adiabatic and CHT wall conditions. The turbulent inlets are created by using the vortex method which is validated for fully developed flow. The inlets are shown to have only small effect in bulk of the flow, but non-negligible effect near walls. The adiabatic and CHT cases show practically no difference in the logarithmic layer and upward, whereas near walls the difference becomes significant due to thermal inertia of the pipe wall. In bulk of the flow, the mean and fluctuating quantities show good agreement with the experiment. CHT simulations by using different meshes and flow velocities are then considered. A coarse mesh is found to yield qualitative agreement but significant errors in e.g. Reynolds stresses near walls. Temperature fluctuation intensity at the pipe inner surface is fairly similar for both meshes. Normalized profiles and spectra for different velocities are qualitatively similar, but some differences exist e.g. in distributions of wall temperature fluctuation intensity.

GE Appliance Park Louisville, KY Plant Wide Assessment Final Report October 25th, 2007

Energy Technology Data Exchange (ETDEWEB)

Chandon Rao; Richard Urschel

2007-10-25

Used a team of experts to analyze and model major systems at a large industrial appliance manufacturer. During the data gathering stage, the team specifically looked for baselining the efficiency of the systems as well as developing short term and longer term efficiency projects. Electrical distribution, Compressed air generation and thermal heat recovery for the production facility and front office heating and cooling optimization were all baselined during the study.

Okanagan indoor wood burning appliance inventory survey

International Nuclear Information System (INIS)

2001-01-01

A survey was conducted to determine the usage and nature of wood burning appliances used by residents in British Columbia's Okanagan region. The objective was to better understand this source of air quality concern and to facilitate strategic planning, guidelines and legislation. The survey also provides a baseline to track the effectiveness of any reduction strategies. It identifies the different types of wood burning appliances used in the community and presents residential options about potential bylaws to protect air quality. The receptivity of households to switch to more efficient wood burning appliances was also examined. The survey completes a portion of an overall emissions inventory for the Okanagan Valley. Environment Canada uses the particulate loading results to model the air quality in the airshed. Results showed that approximately 21 per cent of the households in the Okanagan use indoor wood burning appliances, and burn an average of 2.3 cords of wood each year. Only 11 per cent of the appliances are considered to have advanced burning technology. It is projected that the use of wood burning appliances in the Okanagan will increase by 5 to 7 per cent in the next 2 years. Most residents have good burning habits, but some improvements can still be made. Many residents are considering exchanging old wood burning appliances for clean burning technology appliances for environmental and health reasons. Most households would support a bylaw to control nuisance amounts of smoke from wood burning appliances. 20 tabs., 5 figs

The International Database of Efficient Appliances (IDEA): A new tool to support appliance energy-efficiency deployment

International Nuclear Information System (INIS)

Gerke, Brian F.; McNeil, Michael A.; Tu, Thomas

2017-01-01

Highlights: •IDEA collects, organizes, and stores data on appliance features and efficiency. •Data can be gathered for any appliance type on any international market. •IDEA enables new approaches to efficiency deployment and monitoring. •Techniques are developed for cross-market comparison of energy-savings potential. •We find significant cost-effective energy-savings potential from efficiency for Indian and Chinese refrigerators. -- Abstract: Appliance energy-efficiency programs are a central component of many countries’ energy-policy portfolios. A major barrier to optimal implementation of these programs is lack of data to determine market baselines, assess the potential for cost-effective energy savings, and track markets over time to evaluate and verify program impacts. To address this gap, we have developed the International Database of Efficient Appliances (IDEA), a suite of software tools that automatically gathers data that is currently dispersed across various online sources and compiles it into a unified repository of information on efficiency, price, and features for a diversity of appliances and devices in markets around the world. In this article we describe the framework and functionality of IDEA, and we demonstrate its power as a resource for research and policy development related to appliance energy efficiency. Using IDEA data for refrigerators in China and India, we assess the potential for cost-effective energy savings within each market by computing robust indicators that can also be easily compared across different appliances and markets. We find that significant cost-effective savings are available on both markets. We discuss implications for the development of future energy-efficiency deployment programs.

The Design, Construction, and Experimental Evaluation of a Compact Thermoacoustic-Stirling Engine Generator for Use in a micro-CHP Appliance

Science.gov (United States)

Wilcox, Douglas A., Jr.

Micro combined heat and power or micro-CHP is the simultaneous generation of useful heat and electricity on a residential scale. The heat and electricity are produced at the point of use, avoiding the distribution losses associated with a centralized power plant. These appliances combine a conventional gas-fired condensing boiler with an electric power module capable of generating electricity from the heat of combustion. Currently, the leading power modules for micro-CHP appliances are free-piston Stirling engines (FPSEs) which can generate 1050 watts of electricity at a thermal-to-electric efficiency of 26%.[1] These external combustion engines have been under development for the last 25 years, with FPSE micro-CHP appliances only recently being introduced to the commercial market. Publications by developers assert unlimited service life and high efficiency, with low noise and emissions; but despite these claims, the actual reliability and cost of manufacturing has prevented their successful mass-market adoption. A Thermoacoustic-Stirling Engine Generator or TaSEG is one possible alternative to FPSE's. A TaSEG uses a thermoacoustic engine, or acoustic heat engine, which can efficiently convert high temperature heat into acoustic power while maintaining a simple design with fewer moving parts than traditional FPSE's. This simpler engine is coupled to an electrodynamic alternator capable of converting acoustic power into electricity. This thesis outlines the design, construction, and experimental evaluation of a TaSEG which is appropriate for integration with a gas burner inside of a residential micro- CHP appliance. The design methodology is discussed, focusing on how changes in the geometry affected the predicted performance. Details of its construction are given and the performance of the TaSEG is then outlined. The TaSEG can deliver 132 watts of electrical output power to an electric load with an overall measured thermal-to-electric (first law) efficiency of eta

46 CFR 199.70 - Personal lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Personal lifesaving appliances. 199.70 Section 199.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS... appliances. (a) Lifebuoys. Each vessel must carry lifebuoys approved under approval series 160.150 as follows...

Microbiologically influenced corrosion of orthodontic metallic appliances.

Science.gov (United States)

Kameda, Takashi; Oda, Hirotake; Ohkuma, Kazuo; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

2014-01-01

Biocorrosion (microbiologically influenced corrosion; MIC) occur in aquatic habitats varying in nutrient content, temperature, stress and pH. The oral environment of organisms, including humans, should be one of the most hospitable for MIC. Corrosion of metallic appliances in the oral region is one cause of metal allergy in patients. In this study, an inductively coupled plasma-optical emission spectrometer revealed elution of Fe, Cr and Ni from stainless steel (SUS) appliances incubated with oral bacteria. Three-dimensional laser confocal microscopy also revealed that oral bacterial culture promoted increased surface roughness and corrosion pits in SUS appliances. The pH of the supernatant was lowered after co-culture of appliances and oral bacteria in any combinations, but not reached at the level of depassivation pH of their metallic materials. This study showed that Streptococcus mutans and Streptococcus sanguinis which easily created biofilm on the surfaces of teeth and appliances, did corrode orthodontic SUS appliances.

Characterization of electrical appliances in transient state

Science.gov (United States)

Wójcik, Augustyn; Winiecki, Wiesław

2017-08-01

The article contains the study about electrical appliance characterization on the basis of power grid signals. To represent devices, parameters of current and voltage signals recorded during transient states are used. In this paper only transients occurring as a result of switching on devices are considered. The way of data acquisition performed in specialized measurement setup developed for electricity load monitoring is described. The paper presents the method of transients detection and the method of appliance parameters calculation. Using the set of acquired measurement data and appropriate software the set of parameters for several household appliances operating in different operating conditions was processed. Usefulness of appliances characterization in Non-Intrusive Appliance Load Monitoring System (NIALMS) with the use of proposed method is discussed focusing on obtained results.

Documentation of Appliances & Interaction Devices

DEFF Research Database (Denmark)

2004-01-01

The interaction devices and appliances explored in the WorkSPACE project, address spatial computing in the context of work. We have developed and explored a range of appliances and interaction devices. The scope has been to develop tools for support of collaboration by mixing digital and physical...

46 CFR 195.06-1 - Lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 195.06-1 Section... VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Lifesaving Appliances and Arrangements § 195.06-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be...

Crew appliance study

Science.gov (United States)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Viable crew appliance concepts were identified by means of a thorough literature search. Studies were made of the food management, personal hygiene, housekeeping, and off-duty habitability functions to determine which concepts best satisfy the Space Shuttle Orbiter and Modular Space Station mission requirements. Models of selected appliance concepts not currently included in the generalized environmental-thermal control and life support systems computer program were developed and validated. Development plans of selected concepts were generated for future reference. A shuttle freezer conceptual design was developed and a test support activity was provided for regenerative environmental control life support subsystems.

Fibrotic encapsulation of orthodontic appliance in palate.

Science.gov (United States)

Muthu, Jananni; Muthanandam, Sivaramakrishnan; Umapathy, Gubernath; Kannan, Anitha Logaranjani

2017-01-01

Iatrogenic trauma though not serious is very common in dental practice. Orthodontic treatment can inflict such injuries as they are prolonged over a long period of time. Ill-fabricated orthodontic appliances, such as wires and brackets, or the patients' habits such as application of constant pressure over the appliance can traumatize the adjacent oral soft tissues. In rare cases, these appliances can get embedded into the mucosa and gingival tissues. This case report describes one such case of iatrogenic trauma to the palatal mucosa due to entrapment of a tongue spike appliance and its surgical management.

46 CFR 188.27-1 - Lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be in accordance with the requirements for...

46 CFR 90.27-1 - Lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 90.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 90.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements must be in accordance with subchapter W (Lifesaving...

46 CFR 70.28-1 - Lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 70.28-1 Section... PROVISIONS Lifesaving Appliances and Arrangements § 70.28-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements on passenger vessels must be in accordance with subchapter W...

What's driving energy efficient appliance label awareness and purchase propensity?

International Nuclear Information System (INIS)

Mills, Bradford; Schleich, Joachim

2010-01-01

The EU appliance energy consumption labeling scheme is a key component of efforts to increase the diffusion of energy-efficient household appliances. In this paper, the determinants of consumer knowledge of the energy label for household appliances and the choice of class-A energy-efficient appliances are jointly estimated using data from a large survey of more than 20,000 German households. The results for five major appliances suggest that lack of knowledge of the energy label can generate considerable bias in both estimates of rates of uptake of class-A appliances and in estimates of the underlying determinants of choice of class-A appliance. Simulations of the choice to purchase a class-A appliance, given knowledge of the labeling framework, reveal that residence characteristics and, in several cases, regional electricity prices strongly increase the propensity to purchase a class-A appliance, but socio-economic characteristics have surprisingly little impact on appliance energy-class choice.

A comparative study of two-piece ostomy appliances.

Science.gov (United States)

Welser, Marion; Riedlinger, Inge; Prause, Ulla

The quality of life of people with a stoma may be affected by peristomal skin disorders and by frequent unplanned changes of ostomy appliances due to problems with those appliances. The aim of this study was to evaluate two new, two-piece ostomy appliances with mechanical couplings (both from the SenSura range by Coloplast) and their ability to address areas that may be important to the quality of life of people with stomas, including appliance changes, stool seepage and overfilling. The study design featured two comparative, crossover, randomized multi-centre studies that were conducted in Germany. The SenSura appliances were evaluated against established reference appliances. Seventy-three individuals with a colostomy (closed-end appliances) and 75 individuals with an ileostomy (drainable appliances) participated in the studies. The participants tested 4-6 flanges of each type within a maximum period of two weeks. The results demonstrated that there was less seepage of stool observed under the SenSura flange when it was removed (pappliances. The SenSura flanges had better adhesion and flexibility and were easier to remove than the references (pappliances on quality of life indicators - there were fewer unplanned changes and less seepage of stool was observed in patients using the SenSura products.

38 CFR 17.150 - Prosthetic and similar appliances.

Science.gov (United States)

2010-07-01

... appliances. 17.150 Section 17.150 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.150 Prosthetic and similar appliances... appliances including invalid lifts and therapeutic and rehabilitative devices, and special clothing made...

Equipment and appliances for underwater operations. Pt. 2

International Nuclear Information System (INIS)

Krueger, P.

1976-01-01

The 6/75 edition of 'mt' reported on the 'ARGE underwater appliances' and the study on 'design development of appliances and equipment for underwater use' in a brief summary. One of these designs, the 'unmanned DSWS underwater appliance' was described in detail. The present article describes three further design developments mentioned in the above study and which are based on unmanned appliances connected to the mother-ship. These designs were developed by Preussag-Meerestechnik. (orig.) [de

Office management of obstructive sleep apnoea: appliances.

Science.gov (United States)

Johnson, Matthew D

2015-08-01

Oral appliances are becoming increasingly common in the treatment of obstructive sleep apnoea (OSA). They work by advancing the mandible and opening the pharynx. There are several types of devices available for use. Many patients intolerant to continuous positive airway pressure (CPAP) are using oral appliances for OSA. Oral appliances have been shown to improve polysomnography, quality of life and health measures associated with OSA. There is current work to better identify patients who are ideal candidates. Development of titratable devices and monitoring are optimizing usage. They have been compared with CPAP, with both showing improvement in OSA; however, CPAP remains superior overall. Oral appliances are becoming first-line therapy for mild and moderate OSA. They provide a meaningful alternative in severe OSA for patients unable to use CPAP. Device titration and usage monitoring are beginning to hone oral appliances as a therapeutic option.

Population at high-risk of indoor heatstroke: the usage of cooling appliances among urban elderlies in Japan.

Science.gov (United States)

Kondo, Masahide; Ono, Masaji; Nakazawa, Kouichi; Kayaba, Momoko; Minakuchi, Emiko; Sugimoto, Kazutoshi; Honda, Yasushi

2013-05-01

Heatstroke due to a heat wave during the summer is one of the commonly known health impacts of climate change in Japan. The elderly are particularly at high-risk of developing indoor heatstroke with poor prognosis. This study aims to describe the population among elderlies at high-risk of indoor heatstroke by focusing on the usage of cooling appliances. We conducted a web-based household survey in eight urban areas during the winter season of 2011. Households with a person aged 65 and over were selected as samples from panel members of a research firm, and the oldest member of the household was queried about his/her usage of cooling appliances. The population at high-risk of indoor heatstroke is defined as the elderly staying in a room without cooling appliances, or not using the installed cooling appliances, or turning the cooling appliances on only when the room temperature is above 28 °C. 15.4 and 19.1 % of the elderlies living in urban areas of Japan are identified as at high-risk of indoor heatstroke during activity time and sleeping time, respectively, according to the definition of high-risk of indoor heatstroke in this study. These figures are not negligible since the consequences of heatstroke are grave, but its risk can be eliminated by an appropriate usage of cooling appliances. The preventive interventions are needed to protect the elderlies at high-risk of heatstroke.

Load Characterization for small domestic appliances and electronics

NARCIS (Netherlands)

Van der Sluis, P.

2009-01-01

In this report, the energy consumption of small domestic loads has been analysed. To make the around 100 types of appliances considereda bit manageable, the appliances were categorized into several groups. The possibilities for time-shifting of the energy use of these small appliances was

Removable orthodontic appliances: new perspectives on capabilities and efficiency.

Science.gov (United States)

Hamid Zafarmand, A; Mahdi Zafarmand, M

2013-06-01

Removable appliances are a dependable choice for many patients but like all orthodontic appliances, they have some limitations in use. Patient selection and appropriate appliance design are two key factors for success. Many patients, especially adults, prefer intra-oral appliances to extra-oral devices. Sometimes a removable intra-oral appliance can solve a dental problem in a shorter period of time compared to fixed treatment, and this has also been repeatedly seen in molar distalisation. From the interceptive perspective, the appliance can prevent or alleviate an impending crowding for erupting permanent incisors. This article describes 5 patients with different orthodontic problems: impending crowding for erupting upper canine with 2 approaches, provision of space for upper cuspids, resolution of chronic attrition of anterior teeth, relief of space shortage for upper canines eruption, and reduction of excess overjet. All subjects were treated with removable appliances of various designs.

46 CFR 109.209 - Appliances for watertight integrity.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 109.209 Section 109... OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting underway, the master or person in charge shall insure that each appliance for watertight integrity is...

42 CFR 409.14 - Supplies, appliances, and equipment.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Supplies, appliances, and equipment. 409.14 Section... Hospital Services § 409.14 Supplies, appliances, and equipment. (a) Except as specified in paragraph (b) of this section, Medicare pays for supplies, appliances, and equipment as inpatient hospital or inpatient...

Gas appliances in the domestic market - legal basis and questioning concerning the Directive for Gas Appliances

International Nuclear Information System (INIS)

Rienen, W. van

1994-01-01

Four years after the Directive for Gas Appliances has been passed by the European Community it shows the first effects on the market. Gas appliances bearing an CE label can prove that the EC-standardised demands are observed. Thus it can be demanded from every member state by law not to hinder a launch on the market and the initiation. The directive also effects the demands for national environmental protection. A new DVGW (Deutscher Verein des Gas und Wasserfaches e.V.) quality label for gas appliances is going to certify the observance of a quality level which exceeds the minimum EC level. (orig.) [de

Implementing peak load reduction algorithms for household electrical appliances

International Nuclear Information System (INIS)

Dlamini, Ndumiso G.; Cromieres, Fabien

2012-01-01

Considering household appliance automation for reduction of household peak power demand, this study explored aspects of the interaction between household automation technology and human behaviour. Given a programmable household appliance switching system, and user-reported appliance use times, we simulated the load reduction effectiveness of three types of algorithms, which were applied at both the single household level and across all 30 households. All three algorithms effected significant load reductions, while the least-to-highest potential user inconvenience ranking was: coordinating the timing of frequent intermittent loads (algorithm 2); moving period-of-day time-flexible loads to off-peak times (algorithm 1); and applying short-term time delays to avoid high peaks (algorithm 3) (least accommodating). Peak reduction was facilitated by load interruptibility, time of use flexibility and the willingness of users to forgo impulsive appliance use. We conclude that a general factor determining the ability to shift the load due to a particular appliance is the time-buffering between the service delivered and the power demand of an appliance. Time-buffering can be ‘technologically inherent’, due to human habits, or realised by managing user expectations. There are implications for the design of appliances and home automation systems. - Highlights: ► We explored the interaction between appliance automation and human behaviour. ► There is potential for considerable load shifting of household appliances. ► Load shifting for load reduction is eased with increased time buffering. ► Design, human habits and user expectations all influence time buffering. ► Certain automation and appliance design features can facilitate load shifting.

46 CFR 108.114 - Appliances for watertight and weathertight integrity.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Appliances for watertight and weathertight integrity. (a) Appliances to ensure watertight integrity include... watertight decks and bulkheads. (b) Appliances to ensure weathertight integrity include weathertight doors...

Embedded Systems for Smart Appliances and Energy Management

CERN Document Server

Neumann, Peter; Mahlknecht, Stefan

2013-01-01

This book provides a comprehensive introduction to embedded systems for smart appliances and energy management, bringing together for the first time a multidisciplinary blend of topics from embedded systems, information technology and power engineering.  Coverage includes challenges for future resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.   Provides a comprehensive, multidisciplinary introduction to embedded systems for smart appliances and energy management; Equips researchers and engineers with information required to succeed in designing energy management for smart appliances; Includes coverage of resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.  

46 CFR 174.100 - Appliances for watertight and weathertight integrity.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Offshore Drilling Units § 174.100 Appliances for watertight and weathertight integrity. (a) Appliances to... watertight closures for openings in watertight decks and bulkheads. (b) Appliances to insure weathertight...

Acceptability and attractiveness of intra- and extra-oral orthodontic appliances.

Science.gov (United States)

Abu Alhaija, Elham S J; Karajeh, M A

2013-01-01

To evaluate the acceptability of different intra-oral and extra-oral orthodontic appliances, to rank orthodontic appliances from the most to the least attractive and to investigate the factors that may affect the acceptance of orthodontic treatment. A random sample of 800 students (schoolchildren and university students) were invited to participate in this study and a total of 688 students were included (86%). A self-administrated structured questionnaire was constructed for the purpose of this study. More than one-half in each age group (53%) claimed that they would accept to have orthodontic treatment. Acceptance of the different orthodontic appliances was affected by gender, age and type of school. Removable appliance was reported as the most acceptable and facemask was reported as the least acceptable orthodontic appliances. Majority of subjects ranked ceramic and facemask appliances as the most and the least attractive orthodontic appliances, respectively. The predictor variables for the acceptance of orthodontic treatment were perceived demand for orthodontic treatment, perceived positive effect of orthodontic treatment and expected benefits from orthodontic treatment. Removable appliance was the most acceptable orthodontic appliance whereas ceramic appliance was ranked as the most attractive one. Facemask was the least acceptable and the least attractive option.

Designing appliances for mobile commerce and retailtainment

OpenAIRE

Roussos, George; Kourouthanassis, P.; Moussouri, T.

2003-01-01

In the emerging world of the new consumer and the `anytime, anywhere' mobile commerce, appliances are located at the collision point of the retailer and consumer agendas. The consequence of this is twofold: on the one hand appliances that were previously considered plain and utilitarian become entertainment devices and on the other, for the effective design of consumer appliances it becomes paramount to employ multidisciplinary expertise. In this paper, we discuss consumer perceptions of a re...

14 CFR 21.502 - Approval of materials, parts, and appliances.

Science.gov (United States)

2010-01-01

... appliances. 21.502 Section 21.502 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF..., Materials, Parts, and Appliances: Import § 21.502 Approval of materials, parts, and appliances. (a) A material, part, or appliance, manufactured in a foreign country with which the United States has an...

15 CFR 9.3 - Appliances and equipment included in program.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Appliances and equipment included in... VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.3 Appliances and equipment included in program. The appliances and equipment included in this program are room...

Decision-making in electrical appliance use in the home

International Nuclear Information System (INIS)

Yamamoto, Yoshihiro; Suzuki, Akihiko; Fuwa, Yasuhiro; Sato, Tomohiro

2008-01-01

This paper presents the results of a survey as well as an argument from the viewpoint of behavioral economics with the aim of clarifying how consumers make decisions about electrical appliance use in the home. A survey of consumers showed that most have little awareness of the energy efficiency of appliances, the price of the services produced by electrical appliances, or electricity rates. These findings indicate that price does not function as a signal in electricity consumption through electrical appliance use. Rather, we found that consumer decision-making in electricity consumption is dependent on the characteristics of the particular electrical appliances they use. Additionally, we argue that the payment system for home electricity consumption plays an important role in decision-making, causing biases due to aspects of human psychology discussed here in terms of satisficing and heuristics, payment decoupling, and budgeting. We conclude that decision-making about electrical appliance use and electricity consumption in the home is not always rational and is affected both by the particular characteristics of appliances and the payment system for electricity consumption along with human psychology

Social perceptions of adults wearing orthodontic appliances: a cross-sectional study.

Science.gov (United States)

Jeremiah, H G; Bister, D; Newton, J T

2011-10-01

This study ascertained the influence of orthodontic appliances on subjective ratings for social competence (SC), intellectual ability (IA), psychological adjustment (PA), and attractiveness in young adult orthodontic patients. A cross-sectional analytical questionnaire study was conducted with 130 undergraduates from the UK. Each participant was asked to look at a single, randomly assigned colour photograph of a young adult female and then asked to make judgements concerning her personal characteristics. Five modified photographs of the same young adult female were used: (1) no appliance, (2) stainless steel fixed orthodontic appliance, (3) ceramic fixed orthodontic appliance, (4) gold fixed orthodontic appliance, and (5) clear colourless aligner. Likert scales with higher scores indicating more positive ratings were used. The results were analysed using chi-square test, one-way univariate analysis of variance, and post hoc Tukey-B and Kruskal-Wallis tests. The results showed that greater perceived IA was associated with the appearance of no appliance (mean values: 7.56) rather than steel (6.67) or ceramic appliances (6.65) but similar to the gold (7.35) and aligner (7.08) appliances. No significant differences between the different orthodontic appliance appearances were found for SC and PA. A trend existed where the no appliance image (resembling a lingual appliance) or clear aligner was considered more attractive than the visible buccal fixed appliances. In the absence of other information, the judgements an individual young adult makes concerning the personal characteristics of a young adult are influenced by dental appearance and orthodontic appliance design. This may influence orthodontic appliance choice.

A retrospective cephalometric investigation of two fixed functional orthodontic appliances in class II treatment: Functional Mandibular Advancer vs. Herbst appliance.

Science.gov (United States)

Kinzinger, Gero Stefan Michael; Lisson, Jörg Alexander; Frye, Linda; Gross, Ulrich; Hourfar, Jan

2018-01-01

The objective of the study is to compare skeletal and dental changes in class II patients treated with fixed functional appliances (FFA) that pursue different biomechanical concepts: (1) FMA (Functional Mandibular Advancer) from first maxillary molar to first mandibular molar through inclined planes and (2) Herbst appliance from first maxillary molar to lower first bicuspid through a rod-and-tube mechanism. Forty-two equally distributed patients were treated with FMA (21) and Herbst appliance (21), following a single-step advancement protocol. Lateral cephalograms were available before treatment and immediately after removal of the FFA. The lateral cephalograms were analyzed with customized linear measurements. The actual therapeutic effect was then calculated through comparison with data from a growth survey. Additionally, the ratio of skeletal and dental contributions to molar and overjet correction for both FFA was calculated. Data was analyzed by means of one-sample Student's t tests and independent Student's t tests. Statistical significance was set at p appliance were found, intergroup comparisons showed no statistically significant differences. Almost all measurements resulted in comparable changes for both appliances. Statistically significant dental changes occurred with both appliances. Dentoalveolar contribution to the treatment effect was ≥70%, thus always resulting in ≤30% for skeletal alterations. FMA and Herbst appliance usage results in comparable skeletal and dental treatment effects despite different biomechanical approaches. Treatment leads to overjet and molar relationship correction that is mainly caused by significant dentoalveolar changes.

Unilateral maxillary molar distalization with zygoma-gear appliance.

Science.gov (United States)

Kilkis, Dogan; Bayram, Mehmet; Celikoglu, Mevlut; Nur, Metin

2012-08-01

The aim of this study was to present the orthodontic treatment of a 15-year-old boy with a unilateral maxillary molar distalization system, called the zygoma-gear appliance. It consisted of a zygomatic anchorage miniplate, an inner bow, and a Sentalloy closed coil spring (GAC International, Bohemia, NY). A distalizing force of 350 g was used during the distalization period. The unilateral Class II malocclusion was corrected in 5 months with the zygoma-gear appliance. The maxillary left first molar showed distalization of 4 mm with an inclination of 3°. The maxillary premolars moved distally with the help of the transseptal fibers. In addition, there were slight decreases in overjet (-0.5 mm) and maxillary incisor inclination (-1°), indicating no anchorage loss from the zygoma-gear appliance. Preadjusted fixed appliances (0.022 × 0.028-in, MBT system; 3M Unitek, Monrovia, Calif) were placed in both arches to achieve leveling and alignment. After 14 months of unilateral distalization with the zygoma-gear appliance and fixed appliances, Class I molar and canine relationships were established with satisfactory interdigitation of the posterior teeth. Acceptable overjet and overbite were also achieved. This article shows that this new system, the zygoma-gear appliance, can be used for unilateral maxillary molar distalization without anchorage loss. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Advances in household appliances- A review

International Nuclear Information System (INIS)

Bansal, Pradeep; Vineyard, Edward; Abdelaziz, Omar

2011-01-01

An overview of options and potential barriers and risks for reducing the energy consumption, peak demand, and emissions for seven key energy consuming residential products (refrigerator-freezers, dishwashers, clothes washers, clothes dryers, electric ovens, gas ovens and microwave ovens) is presented. The paper primarily concentrates on the potential energy savings from the use of advanced technologies in appliances for the U.S. market. The significance and usefulness of each technology was evaluated in order to prioritize the R and D needs to improve energy efficiency of appliances in view of energy savings, cost, and complexity. The paper provides a snapshot of the future R and D needs for each of the technologies along with the associated barriers. Although significant energy savings may be achieved, one of the major barriers in most cases is high first cost. One way of addressing this issue and promoting the introduction of new technologies is to 'level' the playing field for all manufacturers by establishing Minimum Energy Performance Standards (MEPS) which are not cost prohibitive and promoting energy efficient products through incentives to both manufacturers and consumers. - Highlights: → This paper presents latest developments/status of advanced residential appliances. → Stringent minimum energy performance standards can reduce appliance energy use. → There is a potential to reduce energy use in appliances by up to 50%.

Estimating Price Elasticity using Market-Level Appliance Data

Energy Technology Data Exchange (ETDEWEB)

Fujita, K. Sydny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-08-04

This report provides and update to and expansion upon our 2008 LBNL report “An Analysis of the Price Elasticity of Demand for Appliances,” in which we estimated an average relative price elasticity of -0.34 for major household appliances (Dale and Fujita 2008). Consumer responsiveness to price change is a key component of energy efficiency policy analysis; these policies influence consumer purchases through price both explicitly and implicitly. However, few studies address appliance demand elasticity in the U.S. market and public data sources are generally insufficient for rigorous estimation. Therefore, analysts have relied on a small set of outdated papers focused on limited appliance types, assuming long-term elasticities estimated for other durables (e.g., vehicles) decades ago are applicable to current and future appliance purchasing behavior. We aim to partially rectify this problem in the context of appliance efficiency standards by revisiting our previous analysis, utilizing data released over the last ten years and identifying additional estimates of durable goods price elasticities in the literature. Reviewing the literature, we find the following ranges of market-level price elasticities: -0.14 to -0.42 for appliances; -0.30 to -1.28 for automobiles; -0.47 to -2.55 for other durable goods. Brand price elasticities are substantially higher for these product groups, with most estimates -2.0 or more elastic. Using market-level shipments, sales value, and efficiency level data for 1989-2009, we run various iterations of a log-log regression model, arriving at a recommended range of short run appliance price elasticity between -0.4 and -0.5, with a default value of -0.45.

14 CFR 25.1365 - Electrical appliances, motors, and transformers.

Science.gov (United States)

2010-01-01

... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Electrical appliances, motors, and transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF...

Measures for improving the adoption of higher efficiency appliances in Indonesian households: An analysis of lifetime use and decision-making in the purchase of electrical appliances

International Nuclear Information System (INIS)

Wijaya, Muhammad Ery; Tezuka, Tetsuo

2013-01-01

Highlights: ► We observe human psychosocial variables regarding purchase of electrical appliances. ► Two cities with different cultures are subject of this study – Bandung and Yogyakarta. ► Differences in the lifetime of appliances can be attributed to the cultural. ► Ads and store’s staff have the greatest impact on people’s choice of appliances. ► Adoption of higher-efficiency appliances could be implemented based on each culture. - Abstract: One approach to decreasing electricity consumption is to facilitate the replacement of older appliances with new, higher-efficiency. The objectives of this paper are to compare and analyse the replacement of appliances in two cities of Indonesia – Yogyakarta and Bandung – that are characterised by different cultural backgrounds, ethnicities, and decision-making processes in the household purchase of electrical appliances. A questionnaire survey method was employed to obtain information on behavioural economics and human psychosocial variables such as attitudes, beliefs and perceived benefits regarding the replacement and purchase of electrical appliances. The results show that refrigerators in Yogyakarta have a longer lifetime than in Bandung. However, in Bandung, air conditioners, electric fans, rice cookers, and water pumps have a longer lifetime than in Yogyakarta. These differences in the lifetime of appliances can be attributed to the cultural differences within the two cities that are reflected in the manner in which people use electrical appliances as well as to their lack of knowledge regarding appliance operation. An analysis of the factors influencing the purchase of appliances indicated that people in Yogyakarta show a greater awareness of the benefits of adopting higher-efficiency appliances than do persons in Bandung. The following suggestions could be implemented to improve the strategy of encouraging the adoption of higher-efficiency appliances: (1) in Yogyakarta, energy labelling could be

Appliance choice functions in Canadian households. Paper no. IGEC-1-ID02

International Nuclear Information System (INIS)

Aydinalp, M.; Fung, A.; Ugursal, V.I.

2005-01-01

Decisions regarding the purchase of various types of major household appliances are influenced by the economic and demographic characteristics of households, i.e., appliance customers. It is therefore necessary to understand the relationship between these characteristics and the decisions made regarding the purchase of appliances to be able to predict future trends in appliance purchases, and consequently, the future appliance energy consumption of the national stock of appliances. In this paper, a methodology is presented to develop choice functions for the purchase of new major household appliances. This methodology is used to develop appliance choice functions for Canada. (author)

Orthodontic appliance preferences of children and adolescents.

Science.gov (United States)

Walton, Daniel K; Fields, Henry W; Johnston, William M; Rosenstiel, Stephen F; Firestone, Allen R; Christensen, James C

2010-12-01

Although attractiveness and acceptability of orthodontic appliances have been rated by adults for themselves and for adolescents, children and adolescents have not provided any substantial data. The objective of this study was to evaluate preferences and acceptability of orthodontic appliances in children and adolescents. Images of orthodontic appliances previously captured and standardized were selected and incorporated into a computer-based survey. Additional images of shaped brackets and colored elastomeric ties, as well as discolored clear elastomeric ties, were captured and incorporated onto existing survey images with Photoshop (Adobe, San Jose, Calif). The survey displayed 12 orthodontic appliance variations to 139 children in 3 age groups: 9 to 11 years (n = 45), 12 to 14 years (n = 49), and 15 to 17 years (n = 45). The subjects rated each image for attractiveness and acceptability. All images were displayed and rated twice to assess rater reliability. Overall reliability ratings were r = 0.74 for attractiveness and k = 0.66 for acceptability. There were significant differences in bracket attractiveness and acceptability in each age group. The highest-rated appliances were clear aligners, twin brackets with colored ties, and shaped brackets with and without colored ties. Colored elastomeric ties improved attractiveness significantly over brackets without colored ties for children in the 12-to-14 year group. There was a tendency for older subjects to rate clear orthodontic appliances higher than did younger subjects. Ceramic brackets with discolored ties tended to be rated lower than ceramic brackets with new ties and scored lowest in acceptability and attractiveness in all age groups. Girls rated shaped brackets significantly higher than did boys. Children's preferences for orthodontic appliances differ by age and sex. Child and adolescent preferences differ from adult preferences. Copyright © 2010 American Association of Orthodontists. Published by Mosby

Quality of Lab Appliances in Orthodontic Offices.

Science.gov (United States)

Pruzansky, D P; Park, J H

Lab appliances are an integral part of orthodontics, from active treatment to retention. The quality and fit of an appliance can affect the treatment result and stability. This study aims to determine common points of failure in orthodontic appliances, and suggest methods to reduce this rate. A survey consisting of 23 questions was distributed to active members of the American Association of Orthodontists (AAO) via Survey Monkey. The most common appliance to need an adjustment was the wrap-around retainer, with the Hawley retainer as a close second. The least common appliance needing adjustment was the Essix/clear retainer. Respondents were asked which component of each appliance was most commonly responsible for an ill-fit. For Hawley and wrap-around retainers, clasps were the most common problem at 50%, whereas spring aligners had two components - clasps and labial bows, both at 38%. Ill-fitting Essix/clear retainers had gingival impingement (52%) closely followed by poor posterior seating (43%). Communication between the orthodontist and lab technician can be improved by establishing a quality assurance protocol for outgoing and incoming cases. The labial bow of Hawley's, wrap-arounds and spring aligners should be clearly demarcated on the casts. Impressions should be free of distortion and casts should be inspected for accuracy. Clear retainers and positioner should be trimmed to avoid gingival impingement. The type of clasp should be selected based on the anatomy of the teeth, and bands should be checked for accuracy of fit.

Scheduling home appliances for energy efficient buildings

DEFF Research Database (Denmark)

Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

2010-01-01

The number of appliances found in users’ homes is increasing together with electricity consumption of users’ residences. In addition, there is a tendency to consume during the same period leading to demand peaks. During these periods, electricity providers are forced to develop costly methods...... to generate enough power to meet consumers’ requirements. In addition, high demand peaks can lead to electricity shortages or even blackouts in certain areas. In order to avoid demand peaks, users’ appliances should consume electricity in a more distributed way. A new methodology to schedule the usage of home...... appliances is proposed and analyzed. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption threshold, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where...

Emergencies in Orthodontics. Part 2: Management of Removable Appliances, Functional Appliances and other Adjuncts to Orthodontic Treatment.

Science.gov (United States)

Dowsing, Paul; Murray, Alison; Sandler, Jonathan

2015-04-01

In the second of two papers, management of orthodontic emergencies involving appliances other than Fixed appliances will be detailed. Problems relating to removable appliances, as well as other orthodontic adjuncts, will be discussed. Unfortunately, orthodontic appliance breakage does occur, despite the clinicians giving clear and concise instructions to the patients and their parents at fitting. If general dental practitioners have a practical knowledge of how to diagnose problems and to provide appropriate advice or timely 'emergency' treatment, this will significantly reduce the inconvenience for all parties concerned. It should also ensure that treatment progresses in the most efficient and comfortable manner for their patients. In specific situations the early, accurate identification of the problem and instigation of its appropriate management can avoid more serious consequences. Clinical Relevance: Appropriate handling of an orthodontic 'emergency' by the dentist can, on many occasions, provide immediate relief to the patient. This will, in turn, allow treatment to continue in the right direction, thus allowing more efficient and effective use of valuable resources.

Electric emissions from electrical appliances

International Nuclear Information System (INIS)

Leitgeb, N.; Cech, R.; Schroettner, J.

2008-01-01

Electric emissions from electric appliances are frequently considered negligible, and standards consider electric appliances to comply without testing. By investigating 122 household devices of 63 different categories, it could be shown that emitted electric field levels do not justify general disregard. Electric reference values can be exceeded up to 11-fold. By numerical dosimetry with homogeneous human models, induced intra-corporal electric current densities were determined and factors calculated to elevate reference levels to accounting for reduced induction efficiency of inhomogeneous fields. These factors were found not high enough to allow generally concluding on compliance with basic restrictions without testing. Electric appliances usually simultaneously emit both electric and magnetic fields exposing almost the same body region. Since the sum of induced current densities is limited, one field component reduces the available margin for the other. Therefore, superposition of electric current densities induced by either field would merit consideration. (authors)

Crew appliance concepts. Volume 2, appendix B: Shuttle orbiter appliances supporting engineering data. [food management and personal hygiene

Science.gov (United States)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Technical data collected for the food management and personal hygiene appliances considered for the shuttle orbiter are presented as well as plotted and tabulated trade study results for each appliance. Food storage, food operation, galley cleanup, waste collection/transfer, body cleansing, and personal grooming were analyzed.

Ubiquitous monitoring of electrical household appliances.

Science.gov (United States)

Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

2012-11-07

The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

Ubiquitous Monitoring of Electrical Household Appliances

Science.gov (United States)

Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

2012-01-01

The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper. PMID:23202205

Inventory of usage pattern for wood burning appliances

International Nuclear Information System (INIS)

Cooper, David; Joeborn, Inger; Sjoedin, Aake; Munkhammar, Inger; Gustavsson, Lennart

2005-02-01

The Swedish Environmental Research Institute (IVL) in co-operation with the Swedish National Testing and Research Institute (SP) and Statistics Sweden (SCB) have investigated the use of domestic wood burning for wood stoves and open fireplaces. The results from a closer examination of existing national energy statistics for residential heating has enabled a division of the average consumption of firewood for each house by the category 'fireplace for open fire' and 'tiled stove/heating stove/fireplace for wood'. The estimation of emissions can therefore be improved by differentiating emission factors for different wood stoves and open fireplaces. Today, only one emission factor is used. An insight into general firing procedures, wood storage routines etc. was investigated using a questionnaire for the Teleborg area of the city Vaexjoe. The results of this study provide a foundation for further work, which will subsequently enable improvements for emission inventories on small-scale biomass combustion from household appliances

14 CFR 21.305 - Approval of materials, parts, processes, and appliances.

Science.gov (United States)

2010-01-01

..., and appliances. 21.305 Section 21.305 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION..., Parts, Processes, and Appliances § 21.305 Approval of materials, parts, processes, and appliances. Whenever a material, part, process, or appliance is required to be approved under this chapter, it may be...

Initial Evaluation of a Titration Appliance for Temporary Treatment of Obstructive Sleep Apnea.

Science.gov (United States)

Levendowski, Daniel J; Morgan, Todd; Westbrook, Philip

2012-01-01

Custom oral appliances that adjustably advance the mandible provide superior outcomes when treating patients with moderate or severe sleep apnea. Custom appliances, however, are expensive, must be fitted by a dentist, and the likelihood of successful outcomes are difficult to predict. An inexpensive trial appliance, if proven efficacious, might be used to predict custom appliance outcomes or to provide temporary therapeutic benefit. The aim of this initial study was to assess the treatment efficacy of a novel titration oral appliance with that of an optimized custom appliance. Seventeen patients, treated with a custom oral appliance for at least one year, successfully completed a three-night home sleep test. The baseline obstructive sleep apnea severity was established on Night 1 with seven patients exhibiting severe, six moderate and four mild apnea/hypopnea indexes. Patients were randomly assigned to wear their custom appliance or the titration appliance on Nights 2 and 3. Significant reductions in the mean overall and supine apnea indexes (p titration and custom appliances. The proportion of patients who exhibited at least a 50% reduction in the overall apnea index and supine apnea/hypopnea were similar for the titration and custom appliance (~60%). The custom appliance reduced the overall apnea/hypopnea index by 50% in a greater proportion of the patients compared to the titration appliance (77% vs. 53%). The titration appliance significantly reduced the degree of hypoxic exposure across sleep disordered breathing events overall (p titration appliance, but preferred the titration appliance to no therapy. The titration appliance may be useful in assessing oral appliance treatment efficacy. When set to 70% of maximum protrusion, the titration appliance may provide immediate, temporary therapeutic benefit.

Crew appliance concepts. Volume 4, appendix C: Modular space station appliances supporting engineering data. [food management and personal hygiene

Science.gov (United States)

Proctor, B. W.; Reysa, R. P.; Russell, D. J.

1975-01-01

Data collected for the appliances considered for the space station are presented along with plotted and tabulated trade study results for each appliance. The food management, and personal hygiene data are applicable to a six-man mission of 180-days.

Measure Guideline: Combustion Safety for Natural Draft Appliances Through Appliance Zone Isolation

Energy Technology Data Exchange (ETDEWEB)

Fitzgerald, J. [Center for Energy and Environment, Minneapolis, MN (United States); Bohac, D. [Center for Energy and Environment, Minneapolis, MN (United States)

2014-04-01

This measure guideline covers how to assess and carry out the isolation of natural draft combustion appliances from the conditioned space of low-rise residential buildings. It deals with combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage. This subset of houses does not require comprehensive combustion safety tests and simplified prescriptive procedures can be used to address safety concerns. This allows residential energy retrofit contractors inexperienced in advanced combustion safety testing to effectively address combustion safety issues and allow energy retrofits including tightening and changes to distribution and ventilation systems to proceed.

46 CFR 31.36-1 - Lifesaving appliances and arrangements-TB/ALL.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements-TB/ALL. 31.36-1... CERTIFICATION Lifesaving Appliances and Arrangements § 31.36-1 Lifesaving appliances and arrangements—TB/ALL. All lifesaving appliances and arrangements on tank vessels must be in accordance with subchapter W...

Speech and orthodontic appliances: a systematic literature review.

Science.gov (United States)

Chen, Junyu; Wan, Jia; You, Lun

2018-01-23

Various types of orthodontic appliances can lead to speech difficulties. However, speech difficulties caused by orthodontic appliances have not been sufficiently investigated by an evidence-based method. The aim of this study is to outline the scientific evidence and mechanism of the speech difficulties caused by orthodontic appliances. Randomized-controlled clinical trials (RCT), controlled clinical trials, and cohort studies focusing on the effect of orthodontic appliances on speech were included. A systematic search was conducted by an electronic search in PubMed, EMBASE, and the Cochrane Library databases, complemented by a manual search. The types of orthodontic appliances, the affected sounds, and duration period of the speech disturbances were extracted. The ROBINS-I tool was applied to evaluate the quality of non-randomized studies, and the bias of RCT was assessed based on the Cochrane Handbook for Systematic Reviews of Interventions. No meta-analyses could be performed due to the heterogeneity in the study designs and treatment modalities. Among 448 screened articles, 13 studies were included (n = 297 patients). Different types of orthodontic appliances such as fixed appliances, orthodontic retainers and palatal expanders could influence the clarity of speech. The /i/, /a/, and /e/ vowels as well as /s/, /z/, /l/, /t/, /d/, /r/, and /ʃ/ consonants could be distorted by appliances. Although most speech impairments could return to normal within weeks, speech distortion of the /s/ sound might last for more than 3 months. The low evidence level grading and heterogeneity were the two main limitations in this systematic review. Lingual fixed appliances, palatal expanders, and Hawley retainers have an evident influence on speech production. The /i/, /s/, /t/, and /d/ sounds are the primarily affected ones. The results of this systematic review should be interpreted with caution and more high-quality RCTs with larger sample sizes and longer follow-up periods are

Electrical appliance energy consumption control methods and electrical energy consumption systems

Science.gov (United States)

Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

2006-03-07

Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

Electrical appliance energy consumption control methods and electrical energy consumption systems

Science.gov (United States)

Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

2008-09-02

Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

Electrical field of electrical appliances versus distance: A preliminary analysis

International Nuclear Information System (INIS)

Mustafa, Nur Badariah Ahmad; Nordin, Farah Hani; Ismail, Fakaruddin Ali Ahmad; Alkahtani, Ammar Ahmed; Balasubramaniam, Nagaletchumi; Hock, Goh Chin; Shariff, Z A M

2013-01-01

Every household electrical appliance that is plugged in emits electric field even if it is not operating. The source where the appliance is plugged into and the components of household electrical appliance contribute to electric field emission. The electric field may cause unknown disturbance to the environment or also affect the human health and the effect might depends on the strength of the electric field emitted by the appliance. This paper will investigate the strength of the electric field emitted by four different electrical appliances using spectrum analyser. The strength will be captured at three different distances; (i) 1m (ii) 2m and (iii) 3m and analysis of the strength of the electrical field is done based on the three different distances. The measurement results show that the strength of the electric field is strongest when it is captured at 1m and the weakest at 3m from the electrical appliance. The results proved that the farther an object is located from the electrical appliance; the less effect the magnetic field has.

46 CFR 78.17-5 - Valves and closing appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.17-5 Section 78.17-5..., Drills, and Inspections § 78.17-5 Valves and closing appliances. (a) It shall be the duty of the master to see that all valves, including cross connecting valves where fitted, and other appliances such as...

46 CFR 78.47-38 - Valves and closing appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.47-38 Section 78.47-38... Fire and Emergency Equipment, Etc. § 78.47-38 Valves and closing appliances. (a) All valves and closing appliances, or other mechanisms which may be required to be operated for damage control purposes in case of...

46 CFR 108.580 - Personal lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 108.580 Section 108.580 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.580 Personal lifesaving appliances. (a) Lifebuoys. Each unit...

46 CFR 133.70 - Personal lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 133.70 Section 133.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.70 Personal lifesaving appliances. (a) Lifebuoys. Each OSV must...

Les méthodesthermiques de production des hydrocarbures. Chapitre 1 : transfert de chaleur et de masse Thermal Methods of Hydrocarbon Production. Chapter 1 : Heat and Mass Transfer

Directory of Open Access Journals (Sweden)

Bia P.

2006-11-01

Full Text Available Après un rappel général sur le transfert de chaleur et de masse ainsi que sur les lois de conservation dans les milieux continus, on traite de l'adaptation de ces lois au cas des milieux poreux. On donne ensuite des informations quantitatives sur les grandeurs physiques mises en jeu par les phénomènes de transfert en milieu poreux. After making a general review of heat and mass transfer a well as of laws of conservation in continua, this chapter describes how these laws con be adopted to the case of porous media. Quantitative data are then given on the physical magnitudes brought into play by transfer phenomena in porous media.

A cephalometric comparison of treatment with the Twin-block and stainless steel crown Herbst appliances followed by fixed appliance therapy.

Science.gov (United States)

Schaefer, Abbie T; McNamara, James A; Franchi, Lorenzo; Baccetti, Tiziano

2004-07-01

This study compared the effects of 2 treatment protocols for correcting Class II disharmony. The first phase of treatment consisted of functional jaw orthopedics with either the Twin-block or the stainless-steel crown Herbst appliance; the second phase consisted of comprehensive fixed-appliance therapy in both protocols. Each of the 2 samples comprised 28 consecutively treated Class II patients. The mean age at the start of treatment was approximately 12 years, and the mean age at the end of the treatment was approximately 14.5 years in both groups. The duration of the treatment phase with the functional appliance was approximately 13 months, and the duration of fixed-appliance therapy was approximately 15 months in both groups. The sex distribution was identical in the 2 groups. Lateral cephalograms were analyzed at the start of treatment (T1) and at the end of the overall treatment protocol (T2). Nonparametric statistics were used for comparisons of starting forms and of the T1-T2 changes between the 2 treatment groups. The stainless-steel crown Herbst appliance and the Twin-block appliance produced very similar therapeutic modifications in Class II patients, although the Twin-block group exhibited almost 2 mm greater correction of the maxillomandibular differential than did the crown Herbst group. The treatment effects of both protocols led to a normalization of the dentoskeletal parameters at the end of the overall treatment period. Twin-block therapy also induced a greater increase in the height of the mandibular ramus (posterior facial height). Overall, only minor differences were detected in the treatment and posttreatment effects of a compliance-free (crown Herbst) and a noncompliance-free (Twin-block) appliance for correcting Class II disharmony.

42 CFR 409.25 - Drugs, biologicals, supplies, appliances, and equipment.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Drugs, biologicals, supplies, appliances, and... Drugs, biologicals, supplies, appliances, and equipment. (a) Drugs and biologicals. Except as specified... can obtain a continuing supply. (c) Supplies, appliances, and equipment. Except as specified in...

Hydrophilic structures for condensation management in refrigerator appliances

Science.gov (United States)

Kuehl, Steven John; Vonderhaar, John J; Wu, Guolian; Wu, Mianxue

2014-10-21

A refrigerator appliance that includes a freezer compartment having a freezer compartment door, and a refrigeration compartment having at least one refrigeration compartment door. The appliance further includes a mullion with an exterior surface. The mullion divides the compartments and the exterior surface directs condensation toward a transfer point. The appliance may also include a cabinet that houses the compartments and has two sides, each with an exterior surface. Further, at least one exterior surface directs condensation toward a transfer point.

Drawing on international experience to reform the Belgian market for ostomy appliances.

Science.gov (United States)

Simoens, Steven; Van den Steen, Dirk; Vanleene, Veerle; De Maré, Luc; Moldenaers, Ingrid; Debruyne, Hans; Ramaekers, Dirk

2007-02-01

This article aims to review the regulatory framework governing the Belgian ostomy appliance market in the light of the experience of Denmark, France, the Netherlands and Ontario (Canada) with regulation of ostomy appliances. Information about the regulatory framework was derived from the international literature, analysis of legal texts and a survey completed by national experts. The comparative analysis revealed that these countries have adopted varying approaches towards regulating their domestic ostomy appliance market. Strategies to keep down prices include public procurement in Denmark, maximum prices in France and exclusion of expensive appliances from reimbursement in the Netherlands. To contain public expenditure on ostomy appliances, consumption patterns are monitored in the Netherlands, the quantity of reimbursed appliances is limited in Belgium and public reimbursement is restricted in Ontario. Ostomy appliances are generally distributed by community pharmacies and medical equipment shops. In countries that emphasise home care delivery such as Denmark, domiciliary distributors dominate the market to the detriment of community pharmacies which do not seem to be able to offer this service at a competitive price. An avenue for reforming the Belgian ostomy appliance market is proposed which valorizes the role of ostomy care nurses in guiding the choice of ostomy appliances. Furthermore, it is recommended that a competitive tendering process determines the price of ostomy appliances, that reimbursement for service provision by distributors is separated from reimbursement of appliances, and that patients receive a fixed grant from the third-party payer to buy ostomy appliances.

38 CFR 17.153 - Training in the use of appliances.

Science.gov (United States)

2010-07-01

... appliances. 17.153 Section 17.153 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.153 Training in the use of appliances. Beneficiaries supplied prosthetic and similar appliances will be additionally entitled to fitting and training...

LES-ODT Simulations of Turbulent Reacting Shear Layers

Science.gov (United States)

Hoffie, Andreas; Echekki, Tarek

2012-11-01

Large-eddy simulations (LES) combined with the one-dimensional turbulence (ODT) simulations of a spatially developing turbulent reacting shear layer with heat release and high Reynolds numbers were conducted and compared to results from direct numerical simulations (DNS) of the same configuration. The LES-ODT approach is based on LES solutions for momentum on a coarse grid and solutions for momentum and reactive scalars on a fine ODT grid, which is embedded in the LES computational domain. The shear layer is simulated with a single-step, second-order reaction with an Arrhenius reaction rate. The transport equations are solved using a low Mach number approximation. The LES-ODT simulations yield reasonably accurate predictions of turbulence and passive/reactive scalars' statistics compared to DNS results.

14 CFR 183.63 - Continuing requirements: Products, parts or appliances.

Science.gov (United States)

2010-01-01

... appliances. 183.63 Section 183.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Designation Authorization § 183.63 Continuing requirements: Products, parts or appliances. For any approval or certificate for a product, part or appliance issued under the authority of this subpart, or under the...

Measurement of HTO permeability of materials for protective appliances

International Nuclear Information System (INIS)

Yamamoto, H.; Tomooka, M.; Kato, S.; Murata, M.; Kinouchi, N.; Yamamoto, H.

1992-01-01

Tritiated water (HTO) vapor permeabilities were measured for plastic and rubber films used for protective appliances (suits, gloves, wrappings, etc.). The measurement data prove that polyehylene and butyl rubbers are materials suitable for HTO protective appliances with their lower permeability. The data also indicate that desiccating protective appliances before reuse is effective for restoring their original resistances to penetrating HTO vapor when they are repeatedly used. (author)

49 CFR 238.229 - Safety appliances-general.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-general. 238.229 Section 238.229... Equipment § 238.229 Safety appliances—general. (a) Except as provided in this part, all passenger equipment continues to be subject to the safety appliance requirements contained in Federal statute at 49 U.S.C...

Practice of gas appliance engineering in households and trade; Praxis der Gasanwendungstechnik in Haushalt und Gewerbe

Energy Technology Data Exchange (ETDEWEB)

Joos, L.

2002-07-01

This practice oriented dictionary describes gas burners and gas engine technology as also required gases for operation of this appliances. Beside the presentation of this used fuel gases an their characteristica many gas appliances for cooking, heating and hot water treatment etc. are shown and described. Cogeneration is also a topic as reduction of pollutant emissions, gas exchangeability and possibilities to save energy. Many pictures and tables support the understanding of this complex technology. From the authors experiences of 34 years developing gas appliances can profit customer consultants of gas supplies, gas installation crews and constructors of heating systems. Last not least for students this practice oriented completion should be interesting in contrast to the mainly theoretical high school education. (GL) [German] Das vorliegende Buch spiegelt den aktuellen Stand der Gasanwendungstechnik auf dem haushaltlichen und gewerblichen Sektor. Als praxisorientiertes Nachschlagewerk beschreibt es sowohl die Gasbrenner- und Gasgeraetetechnik als auch die fuer den Betrieb dieser Gasgeraete erforderlichen Gase. Neben der Vorstellung der eingesetzten Brenngase und ihrer Kenngroessen wird eine Vielzahl unterschiedlicher Gasgeraete zum Heizen, Kochen, zur Warmwasserbereitung etc. beschrieben und erlaeutert. Darueber hinaus ist die Kraft-Waerme-Kopplung ebenso ein Thema wie die Reduzierung von Schadstoffemissionen, die Austauschbarkeit der Gase und die Moeglichkeiten der Energieeinsparung. Dem besseren Verstaendnis der komplexen Thematik dienen zahlreiche Bilder und Tabellen. Von den praktischen Erfahrungen, die der Autor in 35 Jahren auf dem Gebiet der gasanwendungstechnischen Entwicklung sammelte, profitieren in erster Linie Kundenberater der Gasversorgungsgesellschaften, Gasinstallateure und Heizungsbauer. Aber auch fuer Studenten wird diese praxisbezogene Ergaenzung des ueberwiegend theoretischen Hochschulunterrichts interessant sein. (orig.)

When do energy-efficient appliances generate energy savings? Some evidence from Canada

International Nuclear Information System (INIS)

Young, Denise

2008-01-01

Improvements in the energy efficiency of household appliances have the potential to decrease residential energy use, but these reductions accrue gradually over time as newer appliances replace older models. SHEU-2003 data are used to examine appliance replacement patterns in Canada for refrigerators, freezers, dishwashers, clothes washers and clothes dryers. The data indicate that the ages at which appliances are replaced tend to be lowest for dishwashers and highest for freezers, with over 40% of freezers in use for more than 20 years before being retired. The life spans of Canadian appliances are compared to the underlying assumptions regarding appliance lifetimes used in models of residential energy demand. We find that Canadian appliance retirement patterns differ from those assumed in the previous literature. Socioeconomic factors related to appliance replacement are also examined. We find that replacement patterns can be sensitive to household characteristics such as income, providing evidence that there may be scope for targeted policies aimed at inducing earlier replacements of older household appliances with new energy-efficient models

Extra-oral Appliances in Orthodontic Treatment.

Science.gov (United States)

Almuzian, Mohammed; Alharbi, Fahad; McIntyre, Grant

2016-01-01

Extra-oral appliances are used in orthodontics to apply forces to the jaws, dentition or both and the popularity of these appliances is cyclical. Although the use of retraction headgear for the management of Class II malocclusion has declined over the last 20 years with the refinement of non-compliance approaches, including temporary anchorage devices, headgear still has a useful role in orthodontics. The use of protraction headgear has increased as more evidence of its effectiveness for the treatment of Class lIl malocclusion has become available. This paper describes the mechanics and contemporary uses of headgear in orthodontics for primary care dentists and specialist orthodontists. CPD/CLINICAL RELEVANCE: Extra-oral appliances have specific uses in orthodontic biomechanics. Clinicians using retraction headgear and protraction headgear should be familiar with their clinical indications, the potential problems and how these can be avoided.

42 CFR 410.36 - Medical supplies, appliances, and devices: Scope.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Medical supplies, appliances, and devices: Scope... Services § 410.36 Medical supplies, appliances, and devices: Scope. (a) Medicare Part B pays for the following medical supplies, appliances and devices: (1) Surgical dressings, and splints, casts, and other...

Custom Made Pressure Appliance for Presurgical Sustained ...

African Journals Online (AJOL)

Among the most common complications of this therapy is ulceration due to excessive pressure. A case of presurgical size reduction for a large ear keloid with a custom made pressure appliance is presented. This novel design of the appliance allows for better control over the amount and direction of the pressure applied on ...

Status Checking System of Home Appliances using machine learning

Directory of Open Access Journals (Sweden)

Yoon Chi-Yurl

2017-01-01

Full Text Available This paper describes status checking system of home appliances based on machine learning, which can be applied to existing household appliances without networking function. Designed status checking system consists of sensor modules, a wireless communication module, cloud server, android application and a machine learning algorithm. The developed system applied to washing machine analyses and judges the four-kinds of appliance’s status such as staying, washing, rinsing and spin-drying. The measurements of sensor and transmission of sensing data are operated on an Arduino board and the data are transmitted to cloud server in real time. The collected data are parsed by an Android application and injected into the machine learning algorithm for learning the status of the appliances. The machine learning algorithm compares the stored learning data with collected real-time data from the appliances. Our results are expected to contribute as a base technology to design an automatic control system based on machine learning technology for household appliances in real-time.

The direct conversion of heat into electricity in reactors; Conversion directe de la chaleur en electricite dans les piles

Energy Technology Data Exchange (ETDEWEB)

Devin, B; Bliaux, J; Lesueur, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

The direct conversion of heat into electricity by thermionic emission in an atomic reactor has been studied with the triple aim of its utilisation: as an energy source for a space device, at the head of a conventional conversion system in power installations, or finally in association with the thermoelectric conversion in very low power installations. The laboratory experiments were mainly orientated towards the electron extraction of metals and compounds and their behaviour at high temperatures. Converters furnishing up to 50 amps at 0. 4 volts with an efficiency close to 10 p. 100 have been constructed in the laboratory; the emitters were heated by electron bombardment and were composed of tungsten covered with an uranium carbide deposit or molybdenum covered with cesium. The main aspects of the coupling between the converter and the reactor have been covered from the point of view of electronics: the influence of the mismatching of the load on the temperature of the emitter and the influence of thermal flux density on the temperature of the emitter and the stability of the converter. Converters using uranium carbide as the electron emitter have been tested in reactors. Tests have been made under dynamic conditions in order to determine the dynamic characteristics. The load matching curves have been constructed and the overall performances of several cells coupled in such a way as to form a reactor rod have been deduced. This information is fundamental to the design of a control system for a thermionic conversion reactor. The problems associated with the reliability of thermionic converters connected in series in the same reactor rod have been examined theoretically. Finally, the absorption isotherms have been drawn at the ambient temperatures for krypton and xenon on activated carbon with the aim of investigating the escape of fission products in a converter. (author) [French] La conversion directe de chaleur en electricite par emission thermionique dans une

Hydrophilic structures for condensation management in appliances

Science.gov (United States)

Kuehl, Steven John; Vonderhaar, John J.; Wu, Guolian; Wu, Mianxue

2016-02-02

An appliance that includes a cabinet having an exterior surface; a refrigeration compartment located within the cabinet; and a hydrophilic structure disposed on the exterior surface. The hydrophilic structure is configured to spread condensation. The appliance further includes a wicking structure located in proximity to the hydrophilic structure, and the wicking structure is configured to receive the condensation.

Modeling of GE Appliances: Cost Benefit Study of Smart Appliances in Wholesale Energy, Frequency Regulation, and Spinning Reserve Markets

Energy Technology Data Exchange (ETDEWEB)

Fuller, Jason C.; Parker, Graham B.

2012-12-31

This report is the second in a series of three reports describing the potential of GE’s DR-enabled appliances to provide benefits to the utility grid. The first report described the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The third report will explore the technical capability of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation. In this report, a series of analytical methods were presented to estimate the potential cost benefit of smart appliances while utilizing demand response. Previous work estimated the potential technical benefit (i.e., peak reduction) of smart appliances, while this report focuses on the monetary value of that participation. The effects on wholesale energy cost and possible additional revenue available by participating in frequency regulation and spinning reserve markets were explored.

Ubiquitous Monitoring of Electrical Household Appliances 

Directory of Open Access Journals (Sweden)

Raquel Lacuesta

2012-11-01

Full Text Available The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home. The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

The impact of personality on adult patients' adjustability to orthodontic appliances.

Science.gov (United States)

Cooper-Kazaz, Rena; Ivgi, Inbal; Canetti, Laura; Bachar, Eytan; Tsur, Boaz; Chaushu, Stella; Shalish, Miriam

2013-01-01

To evaluate the impact of psychological traits on patients' choice of orthodontic appliances and their adjustability to orthodontic treatment. The sample consisted of 68 adult patients divided into three groups (28 buccal, 19 lingual, and 21 clear aligners). Prior to treatment participants filled out the Brief Symptom Inventory to assess symptoms of mental distress and the Narcissistic Vulnerability Scale to assess narcissistic personality traits. During the first week after appliance delivery and on day 14, patients completed a Health-Related Quality of Life questionnaire to assess their perception of pain and four areas of dysfunction. The correlation between personality traits and patients' reaction to treatment was evaluated. Somatization was the only trait that affected the choice of lingual and clear aligner appliance. Reduced self-esteem regulation was associated with increased pain in all patients, while exploitation was associated with pain in lingual patients. Narcissistic vulnerability slightly influenced patients' adaptability to orthodontic appliances. Although adjustability to lingual appliances was the most difficult, only two parameters were affected by personality features. In the buccal group, adjustability was affected by numerous parameters. Adaptation to the clear aligner appliance was relatively uneventful and least affected by psychological features. Anxious individuals tend to prefer lingual and clear aligner appliances. The selection of lingual and clear aligner appliances governs the patient's response and recovery process, leaving little room for the effect of psychological features. On the other hand, the buccal appliance allows for greater impact of personality traits on adjustability.

Lesão do colo do cafeeiro, causada pelo calor Collar injury- young coffe plants caused by heat

Directory of Open Access Journals (Sweden)

Coaracy M. Franco

1961-01-01

Full Text Available Tem sido observada ocasionalmente uma lesão no colo de cafeeiros novos ao nível do solo. .Estudos dc laboratório mostraram que o caule de cafeeiros novos foram danificados quando ao redor dêle se fêz circular água aquecida às temperaturas de 45 o 50ºC. O aquecimento da superfície do solo, compreendendo o colo de cafeeiro vegetando em laminados, com o auxílio de uma lâmpada de raios infravermelhos, resultou em lesão semelhante àquela observada nas culturas. Essa lesão apareceu em tratamentos cujas temperaturas estiveram entre 44 e 51°C. O fato dessas temperaturas serem freqüentemente observadas em solos expostos ao sol, sugere que a lesão do caule do cafeeiro, observada freqüentemente em cafèzais novos, seja conseqüência do aquecimento excessivo da superfície do solo pelos raios solares.A collar injury of young, field coffee plants at the soil level has been observed occasionally in the summer. The location of the abnormality and the season when it appears .suggested that excessive heating of the soil surface by the sun rays could be its cause. Two experiments were then conducted in the laboratory to investigate this bypothesis. The first experiment consisted in circulating water at the desired temperature around the stem ofyoung coffee plants, using the same apparatus described in a previous paper. In a second experiment the base of the stem and the soil around it was heated by means of a G. E. 250 watts infrared industrial reflector. By changing the distance between the heat source and the plant, different temperatures at the soil surface could be obtained. The results of the first experiment showed that 4 plants out of o that were treated at 45ºC showed injury; the other 2 plants survived without damage. From 5 plants that were treated at 50ºC, 2 showed injury and 3 died shortly after the treatment. All plants subjected to the temperature treatments at 35°C and 40ºC survived without damage, while those treated at 55º

Mobile based Appliances switching using Bluetooth

Science.gov (United States)

Gupta, Sureshchandra J., Dr; Desai, Kalp; Gaikawad, Deepak; Pawar, Vijay N.; Gangal, Devendranath R.

2008-04-01

How many times do you have to get up from your desk to switch on your Air conditioner or fan when you are completely into your table work? How many times do you feel lazy to get off your comfort to switch on/off your home appliances in different rooms? How much energy do you lose in a day for operating your appliances? The solution is either a large amount of manual work—or the idea that is presented over here: APP-CON (APP-CON stands for appliances control). Here the ordinary cell phone with bluetooth capability acts as remote designed in such a manner that it acts as a helping hand to human by reducing its manual work and therefore saving human energy. The cell phone control of APP-CON units lets you access many of your home appliances situated in different rooms by using just a single remote from distance. Electronics hobbyists would love to make such a remote control themselves. But they find it difficult due to complex circuitry rather than the high cost because of using a number of frequency counting techniques and decade counters. The APP-CON system given here overcomes the aforesaid problems by using a single microcontroller and moreover a simple program or software for bluetooth enabled cell phone and employing simple coding and decoding of remote signals. Here the mobile based remote control is used to operate a number of home appliances basically consists of Bluetooth technology. The unit consists of a transmitter and a receiver consisting of a microcontroller. The importance of bluetooth technology is that the signal to be transmitted from transmitter to the receiver is done without requiring line of sight.

Occlus-o-Guide® versus Andresen activator appliance: neuromuscular evaluation.

Science.gov (United States)

Farronato, Giampietro; Giannini, Lucia; Galbiati, Guido; Grillo, Elena; Maspero, Cinzia

2013-05-20

The aim of the present study was to assess the muscular variations at the electromyography (EMG) level for the anterior temporalis muscles and masseter muscles during treatment with Occlus-o-Guide® and Andresen activator appliances. Eighty-two patients (35 males and 47 females) aged between 8 and 12 years (mean age, 10.5±0.8 years) participated in the study. Fifty patients underwent treatment with an Occlus-o-Guide® and 32 patients with an Andresen activator. All patients underwent EMG examination using a Freely EMG (De Gotzen, Legnano, Italy) and surface bipolar electrodes when the appliances were worn for the first time (T0), and after 6 months (T1) and after 12 months (T2) of appliance use. Statistical analysis showed that both at T0 and T2, the percent overlapping coefficient (POC) of the anterior temporalis muscles was not statistically different between the appliance groups. At T0, the POC of the masseter muscles was significantly lower for the Andresen appliance as compared to the Occlus-o-Guide® (p=0.02), while at T2 this significance was lost. At insertion of an appliance, all patients show neuromuscular balance that does not correspond to orthognathic occlusion. Both appliances work by creating muscular imbalance. With the appliances in situ, EMG responses were generally analogous for the Occlus-o-Guide® and the Andresen activator; however, the imbalance was greater and the recovery of the orthological muscular balance was slower in patients under treatment with the Andresen activator as compared to those with the Occlus-o-Guide®.

Realizing potential savings of energy and emissions from efficient household appliances in India

International Nuclear Information System (INIS)

Parikh, Kirit S.; Parikh, Jyoti K.

2016-01-01

The paper projects households' stock of four major electricity consuming appliances till 2030 and explores policy options to accelerate adoption of more energy efficient appliances. India's rapid economic growth has enabled the growing middle class to buy household appliances in increasing numbers. The consequent rise in energy consumption and GHG emissions can be significantly reduced if consumers are motivated by awareness and options in the market to buy energy efficient appliances. India has introduced a star rating scheme for appliances, and even without incentives consumers purchase star-rated appliances. The stock of household appliances is projected using the data of a national sample survey of household consumption, observed sale of star-rated appliances and projected consumption distribution. Estimated savings in households' electricity consumption from just four appliances, ACs, refrigerators, TVs, and ceiling fans, for which data were available, range from 52 bKwh to 145 bkwh in 2030, reductions of 10–27%. The corresponding reduction in CO_2 emissions will be between 42 Mt and 116 Mt in 2030. With policies of finance and bulk procurement to reduce costs, emissions reduction can be 128 Mt in 2030, a reduction of 30%. - Highlights: • Estimates the stock of selected household appliances with 20 classes of rural and urban households in the years 2030 in India. • Assesses the economics of energy efficient appliances. • Estimates spread of selected energy efficient appliances. • Assesses savings in energy consumption and CO_2 emissions in four alternative scenarios. • Suggests policies to promote energy efficient appliances.

14 CFR 3.5 - Statements about products, parts, appliances and materials.

Science.gov (United States)

2010-01-01

..., appliances and materials. 3.5 Section 3.5 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION DEFINITIONS GENERAL REQUIREMENTS § 3.5 Statements about products, parts, appliances... product, part, appliance or material. (b) Prohibition against fraudulent and intentionally false...

Les aciers inoxydables dans les fixations

CERN Document Server

CETIM

2010-01-01

Cet ouvrage, qui fait la synthèse de plusieurs travaux menés par le Cetim, propose une vue d'ensemble sur les aciers inoxydables utilisés pour les fixations. Au sommaire : les normes EN, ISO et ATSM qui s'y rapportent , les désignations symboliques , les nuances et caractéristiques mécaniques , les différentes formes de corrosion, les méthodes pour les détecter , les règles du métier , les mises en oeuvre. L'ouvrage comprend plusieurs fiches matériaux et des tableaux qui présentent les équivalences entre les désignations.

46 CFR 108.645 - Markings on lifesaving appliances.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

46 CFR 108.665 - Appliances for watertight integrity.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 108.665 Section 108.665 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.665 Appliances for watertight integrity...

Corrosion by cooling gases in nuclear reactors; la corrosion par les gaz caloporteurs dans les reacteurs nucleaires

Energy Technology Data Exchange (ETDEWEB)

Darras, R. [Commissariat a l' energie atomique et aux energies alternatives - CEA, Centre de Saclay, Section d' etude de la corrosion par gaz et metaux liquides (France)

1960-07-01

This article begins with a review of the various materials which can be used and the cooling gases in which they may be heated, emphasis being placed on the importance of reaching temperatures as high as possible. This is followed by a few general remarks on the dry oxidation of metals and alloys, particularly with regard to diffusion phenomena and their various possible mechanisms, and also the methods of investigation employed. Finally, the behaviour of the chief nuclear materials heated in the various gases is studied successively. Materials used for fuel (metallic uranium, uranium oxide, carbides and silicides), canning materials (magnesium, aluminium, zirconium, beryllium, stainless and refractory steels), structural materials (ordinary or slightly alloyed steels), and finally moderators (graphite, beryllium oxide) are deal with in this way. This account is backed up both by the results obtained at the CEA and by work published outside or abroad up to the present day. In conclusion, every effort has been made to direct future research on the basis of the foregoing. Reprint of a paper published in Industries Atomiques - no. 9/10, 1959, p. 3-23 [French] Dans cet article, on passe tout d'abord en revue les divers materiaux utilisables et les gaz de refroidissement dans lesquels ils peuvent etre chauffes, en insistant sur l'interet d'atteindre des temperatures aussi elevees que possible. On rappelle ensuite quelques generalites sur l'oxydation seche des metaux et alliages, notamment en ce qui concerne les phenomenes de diffusion et leurs divers mecanismes possibles ainsi que les methodes d'etude. Enfin, le comportement des principaux materiaux nucleaires chauffes dans les divers gaz est etudie successivement. On traita ainsi des materiaux combustibles (uranium metallique, oxyde, carbures et siliciures d'uranium), des materiaux de gainage (magnesium, aluminium, zirconium, beryllium, aciers inoxydables et refractaires), des materiaux de structure (aciers ordinaires

New horizons in orthodontics & dentofacial orthopedics: fixed Twin Blocks & TransForce lingual appliances.

Science.gov (United States)

Clark, William John

2011-01-01

During the 20th century functional appliances evolved from night time wear to more flexible appliances for increased day time wear to full time wear with Twin Block appliances. The current trend is towards fixed functional appliances and this paper introduces the Fixed Twin Block, bonded to the teeth to eliminate problems of compliance in functional therapy. TransForce lingual appliances are pre-activated and may be used in first phase treatment for sagittal and transverse arch development. Alternatively they may be integrated with fixed appliances at any stage of treatment.

Energy efficient appliance choice under the EU labeling scheme

Energy Technology Data Exchange (ETDEWEB)

Mills, Bradford F.; Schleich, Joachim [Fraunhofer-Institut fuer System- und Innovationsforschung (ISI), Karlsruhe (Germany)

2010-02-15

This paper extends the existing empirical literature on consumers' choices when exposed to energy labeling schemes by allowing choices to depend on household socio-economic characteristics, technology-related factors, behavioral and motivational factors, and country conditions in a multi-country analysis. To account for a possible knowledge-based selection bias, the econometric model distinguishes label class knowledge from the energy class choice decision. As a general finding, most covariates show stronger relationships with knowledge of labeling class than with the choice of energy efficiency class. Four factors show particularly strong and expected influences on label class awareness. First, general awareness of household energy use and energy saving technologies spills over into awareness of the energy class of specific appliances. Second, socioeconomic characteristics mater, as education increases label class awareness and older age reduces awareness. Third, economic incentives matter, as stated economic importance of energy saving and higher country electricity prices both generate greater label awareness. By contrast, stated concerns about global warming do not appear to have a broad impact on awareness. Fourth, effective country implementation of the labeling scheme raises label awareness. More surprisingly, most factors that promote awareness of appliance energy classes have a limited influence on actual appliance energy class choice. Efficient energy behavior in the household is not strongly linked to appliance energy class choice. Socio-economic characteristics also have limited influence. This finding is inline with other studies that find that household socio-economic characteristics have relatively weak associations with the adoption of energy efficient technologies (Mills and Schleich 2010, Brohmann et al. 2009). In fact, with education it is vocational degrees rather than university degrees that are positively associated with the propensity to

46 CFR 167.15-28 - Inspection of lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-28 Inspection of lifesaving appliances and arrangements. The inspection of lifesaving appliances and arrangements must be in accordance with the... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection of lifesaving appliances and arrangements...

Treatment of adolescent patients with class II division 1 malocclusion using Eruption guidance appliance: A comparative study with Twin-block and Activator-Headgear appliances.

Science.gov (United States)

Nilsson, Jenny Jiayan Luo; Shu, Xiaochen; Magnusson, Britt Hedenberg; Burt, Idil Alatli

2016-01-01

The aim of this study was to evaluate the compliance and short-term effects of eruption guidance appliance (EGA) in adolescents with class II division 1 malocclusion in comparison with twin-block appliance (TBA) and activator-headgear appliance (A-HG). Dental records of 1886 patients were viewed in this retrospective study 129 patients treated with one of these three functional appliances were identified. 123 fulfilled the inclusion criteria and data were extracted from the dental records. Gender, age, compliance, overjet change at every visit, number of appliance breakages and number of emergency visits apart from appliance breakage were studied. The data were analyzed with Chi-square test, General Linear Model and Fisher scoring test. Results showed that 47 patients were treated with EGA, 38 patients with TBA and 38 patients with A-HG. Mean ages starting the treatment were slightly lower with EGA (11.5 years) than with TBA (12.3 years) and A-HG (11.8 years). Non-compliance was higher in the EGA group (31.9%) than TBA group (26.3%) and A-HG group (23.7%). Mean overjet reduction per month was 0.6 mm for EGA which was lower than TBA group (0.7 mm) and A-HG groups (0.7 mm).The number of emergency visits and appliance breakage were lower in EGA group. However, there was no statistically significant difference between the 3 groups regarding ages,compliance, mean overjet reduction, emergency visits and appliance breakage aspects. In conclusion, this study indicates that EGA is an alternative choice in the treatment of adolescent patients with class II division 1 malocclusion. However, long-term follow-up and cephalometric prospective study should be performed to continue our understanding more about the mechanisms of EGA and more definite conclusions can be made.

49 CFR 238.230 - Safety appliances-new equipment.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-new equipment. 238.230 Section... I Passenger Equipment § 238.230 Safety appliances—new equipment. (a) Applicability. This section..., 2007, that is equipped with a safety appliance, required by the “manner of application” provisions in...

Esthetic perception of orthodontic appliances by Brazilian children and adolescents.

Science.gov (United States)

Kuhlman, Deise Caldas; Lima, Tatiana Araújo de; Duplat, Candice Belchior; Capelli, Jonas

2016-01-01

The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher economic status, golden orthodontic brackets and

Increased BMI in children-an indicator for less compliance during orthodontic treatment with removable appliances.

Science.gov (United States)

von Bremen, Julia; Lorenz, Nathalie; Ludwig, Björn; Ruf, Sabine

2018-02-19

To assess whether or not childhood overweight is associated with lower levels of compliance during orthodontic therapy with removable appliances. Starting in 2011, all upper expansion plates and Sander II appliances were equipped with a Theramon® microsensor chip to assess appliance wear time objectively. According to their pre-treatment, BMI normal weight patients were matched to consecutively treated overweight or obese patients by gender, age, and appliance type. Cooperation was assessed with microelectronic wear time documentation over a period of at least 6 months. A total of 50 patients (25 overweight, 25 normal weight) with upper expansion plates and 64 patients (32 overweight, 32 normal weight) with Sander II appliances were analysed. Spearman Rho coefficients showed an indirect association between BMI and appliance wear time, indicating that the higher the BMI, the less the patients wore their appliances (P appliances (P appliance wear during orthodontic treatment with removable appliances. Additional factors which influenced cooperation during treatment with removable appliances were patient age and appliance type.

Effective Maxillary Protraction with Tandem Traction Bow Appliance

Directory of Open Access Journals (Sweden)

Pravin Kumar S Marure

2014-01-01

Full Text Available Tandem traction bow appliance (TTBA promotes patient compliance, because it is more esthetic and comfortable than extraoral appliances. TTBA should be used only in case where maxillary deficiency and normal mandible is present. Advantages of it includes good oral hygiene, early treatment of any Class III malocclusion, optimal retention, distribution of the forces for protraction to all maxillary teeth, free mandibular movement. It can be used in conjunction with fixed appliances if necessary. This paper includes two case reports. The treatment results in both the cases demonstrated significant skeletal and dental response to TTBA therapy. Skeletal change was primarily a result of anterior movement of the maxilla.

Fixed functional appliances with multibracket appliances have no skeletal effect on the mandible: A systematic review and meta-analysis.

Science.gov (United States)

Ishaq, Ramy Abdul Rahman; AlHammadi, Maged Sultan; Fayed, Mona M S; El-Ezz, Amr Abou; Mostafa, Yehya

2016-05-01

Our aim was to assess the skeletal mandibular changes (anteroposterior and vertical) in circumpubertal patients with fixed functional appliances installed on multibracket appliances compared with untreated patients. An open-ended electronic search of 4 databases (PubMed, Embase, Cochrane Library, and Web of Science) up to April 2014 was performed. Additional searches of relevant journals, reference lists of the retrieved articles, systematic reviews, and gray literature were performed. Specific inclusion and exclusion criteria were applied to identify relevant articles. Quality was evaluated using the Cochrane Collaboration risk of bias tool and the Newcastle-Ottawa scale for prospective controlled clinical trials. Meta-analyses were conducted with fixed and random effects models as appropriate. Statistical heterogeneity was also examined. Seven articles were included in the qualitative synthesis and 5 in the meta-analysis. The included randomized controlled trials were at high risk of bias, and the methodologic quality of the prospective controlled clinical trials was high. Based on assessment of the fixed functional appliance phase in isolation, no difference in mandibular anteroposterior positional changes (SNB angle) (standard mean difference, 0.11°; 95% CI, -0.28, 0.50) was found between the treated and control groups. The vertical dimension was not influenced by the fixed functional appliance treatment. There is little high-quality evidence concerning the relative influence of fixed functional appliances on skeletal and dentoalveolar changes. However, based on the limited evidence, it appears that they have little effect on the skeletal mandibular parameters. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Esthetic perception of orthodontic appliances by Brazilian children and adolescents

Science.gov (United States)

Kuhlman, Deise Caldas; de Lima, Tatiana Araújo; Duplat, Candice Belchior; Capelli, Jonas

2016-01-01

ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher

Esthetic perception of orthodontic appliances by Brazilian children and adolescents

Directory of Open Access Journals (Sweden)

Deise Caldas Kuhlman

Full Text Available ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276 was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those

Effect of Fixed Metallic Oral Appliances on Oral Health.

Science.gov (United States)

Alnazzawi, Ahmad

2018-01-01

There is a substantial proportion of the population using fixed metallic oral appliances, such as crowns and bridges, which are composed of various dental alloys. These restorations may be associated with a number of effects on oral health with variable degrees of severity, to review potential effects of using fixed metallic oral appliances, fabricated from various alloys. The MEDLINE/PubMed database was searched using certain combinations of keywords related to the topic. The search revealed that burning mouth syndrome, oral pigmentation, hypersensitivity and lichenoid reactions, and genotoxic and cytotoxic effects are the major potential oral health changes associated with fixed prosthodontic appliances. Certain oral disorders are associated with the use of fixed metallic oral appliances. Patch test is the most reliable method that can be applied for identifying metal allergy, and the simultaneous use of different alloys in the mouth is discouraged.

Chevilly Larue, L'Hay les Roses: twin geothermal plants

International Nuclear Information System (INIS)

Jeanson, E.

1995-01-01

The Chevilly Larue/L'Hay les Roses (Paris region, France) low energy geothermal plants are interconnected and thus represent the greatest geothermal heat network in Europe. The two plants are 2.5 km apart and supply 13000 collective lodgings in energy using a 60 km network with a 75 MW power. Gas or fuel auxiliary heating systems are used in winter to increase water temperature up to 105 C, but the part of energy released by geothermics remains of about 70 to 80%. The network will be extended in the next years to Fresnes and Villejuif neighbouring towns. In 1996, the SEMHACH company, which manage the two plants, will put into service a mixed electricity and heat production plant in L'Hay les Roses. (J.S.). 2 photos

A modified, lingually supported cantilevered Herbst appliance.

Science.gov (United States)

Snodgrass, D

1996-01-01

This new, fixed-functional appliance/Herbst/Bioprogressive system is designed for patient comfort and mandatory compliance. It also combines the positive clinical effects of four fixed-functional systems. It allows rapid palatal expansion of the upper arch, alveolar uprighting of the lower arch, upper and lower incisor alignment, and sagittal correction of Class II malocclusions to occur simultaneously with one appliance fixed in both arches. It is indicated for use in growing patients with skeletal Class II malocclusions. The ideal timing for treatment is the late mixed dentition. Being able to remove the appliance after one year with the upper second bicuspids erupting slightly Class III so the clinician can immediately begin fixed finishing mechanics would be ideal. This new Herbst design will reduce the frequency of orthognathic surgery and upper bicuspid extraction to camouflage Class II malocclusions. At the same time, it gives total control to the clinician in treating some more difficult, non-compliant patients. Fixed-functional appliances, which improve treatment efficiency and treatment results and provide for patient comfort, while at the same time give the treating clinician almost total control of the three planes of facial growth will open new doors for orthodontic treatment and research in the next century.

Efficacy of custom made oral appliance for treatment of obstructive sleep apnea

Directory of Open Access Journals (Sweden)

V R Cilil

2015-01-01

Full Text Available Introduction: oral appliance for the treatment of OSA is considered as an effective, low-risk alternative to CPAP. Demand for oral appliance increases as an alternative for those who cannot tolerate CPAP and refuse surgery. Oral appliances uses the traditional methods to advance the mandible thus modify the posture and their by enlarge the airway or otherwise reduce the collapsibility. Aims and Objectives: The main objective of this study was to evaluate the efficacy of custom made oral appliance on sleep characteristics of OSA patients. Materials and Methods: Polysomnography was done on 15 patients of 24-60 years of age before (T1, and after the delivery of the custom made oral appliance (T2. Statistical Analysis: Paired t tests were performed to determine the significance of change in the polysomnographic and cephalometric variables. P < 0.05 was considered as significant. Results: All patients with oral appliance showed an improvement in sleep parameters with an increase in sleep efficiency, and desaturation index with the use of oral appliance. ESS and cephalometric findings showed improvement in the sleep apnea in concordance with the sleep parameters. Conclusions: Custom made oral appliance is a useful treatment option for improving quality of sleep and can be considered as an alternative treatment modality.

BLOND, a building-level office environment dataset of typical electrical appliances

Science.gov (United States)

Kriechbaumer, Thomas; Jacobsen, Hans-Arno

2018-03-01

Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

BLOND, a building-level office environment dataset of typical electrical appliances.

Science.gov (United States)

Kriechbaumer, Thomas; Jacobsen, Hans-Arno

2018-03-27

Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

Eulerian Time-Domain Filtering for Spatial LES

Science.gov (United States)

Pruett, C. David

1997-01-01

Eulerian time-domain filtering seems to be appropriate for LES (large eddy simulation) of flows whose large coherent structures convect approximately at a common characteristic velocity; e.g., mixing layers, jets, and wakes. For these flows, we develop an approach to LES based on an explicit second-order digital Butterworth filter, which is applied in,the time domain in an Eulerian context. The approach is validated through a priori and a posteriori analyses of the simulated flow of a heated, subsonic, axisymmetric jet.

16 CFR 305.12 - Labeling for central air conditioners, heat pumps, and furnaces.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Labeling for central air conditioners, heat... (âAPPLIANCE LABELING RULEâ) Required Disclosures § 305.12 Labeling for central air conditioners, heat pumps, and furnaces. (a) Layout. All energy labels for central air conditioners, heat pumps, and...

Study on Semantic Assets for Smart Appliances Interoperability : D-S3: THIRD INTERIM REPORT

NARCIS (Netherlands)

Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

2015-01-01

About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

Study on Semantic Assets for Smart Appliances Interoperability : D-S2: SECOND INTERIM REPORT

NARCIS (Netherlands)

Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

2014-01-01

About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

Study on Semantic Assets for Smart Appliances Interoperability : D-S1: FIRST INTERIM REPORT

NARCIS (Netherlands)

Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

2014-01-01

About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

A comparison between indirect and objective wear-time assessment of removable orthodontic appliances.

Science.gov (United States)

Schott, Timm C; Meyer-Gutknecht, Hannes; Mayer, Nicolai; Weber, Joachim; Weimer, Katja

2017-04-01

Patients do not always adhere to the wear times prescribed for removable orthodontic appliances. We evaluated the validity and usability of indirect wear-time assessment methods by comparing wear-time estimates with microelectronically measured wear times in patients with removable orthodontic appliances. Wear times of 33 expansion plates, 34 functional appliances, and 42 retention plates of patients aged 6-20 years (12.3±2.9 years, 50.5% female) were indirectly determined by practitioners using a questionnaire assessing five parameters on a 5-point Likert scale: appliance handling, appliance appearance, bite shift, tooth movement, and appliance fit. The perceived difficulty in assessing each parameter was rated. Actual wear times were evaluated with microelectronic sensors in the appliances. Regression analyses revealed that practitioners' decisions about wear times varied depending on the type of appliance and criteria used, with only one standard criterion best predicting estimated wear time for each appliance. Different standard criteria were better predictors of measured wear time: 22.3% of wear-time variability was explained by expansion plate appearance, 31.2% by functional appliance handling, and 18.8% by retainer fitting. However, practitioners rated the difficulty of assessment in most cases as 'easy'. The study was not double blinded for technical reasons, and practitioners may have considered the evaluation criteria more carefully than in normal daily practice. Practitioners' decisions about wear times based on standard criteria strongly vary depending on the type of appliance and criteria used. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

Electric household appliances lighting. Synthesis; Electromenager eclairage. Note de synthese

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-01

This study has been realized on 10000 families in order to know the French behavior concerning the electric household appliances and the lighting of their accommodation. The document presents statistically the answers to the questions on the electric household in the accommodation, the choice criteria, the use conditions, the washing temperatures, the nature of the electric household appliances, the microwave ovens, the influence of the energy-label on the appliances and the lighting. (A.L.B.)

The use of functional appliances in contemporary orthodontic practice.

Science.gov (United States)

DiBiase, A T; Cobourne, M T; Lee, R T

2015-02-16

Functional appliances have been used for over 100 years in orthodontics to correct Class II malocclusion. During this time numerous different systems have been developed often accompanied by claims of modification and enhancement of growth. Recent clinical evidence has questioned whether they really have a lasting influence on facial growth, their skeletal effects appearing to be short term. However, despite these findings, the clinical effectiveness of these appliances is acknowledged and they can be very useful in the correction of sagittal arch discrepancies. This article will discuss the clinical use of functional appliances, the underlying evidence for their use and their limitations.

33 CFR 150.507 - How must the operator service inflatable lifesaving appliances?

Science.gov (United States)

2010-07-01

... inflatable lifesaving appliances? 150.507 Section 150.507 Navigation and Navigable Waters COAST GUARD... Specialty Equipment Inflatable Lifesaving Appliances § 150.507 How must the operator service inflatable lifesaving appliances? (a) The operator must service each inflatable liferaft according to 46 CFR subpart 160...

Face and neck dermatitis from a stainless steel orthodontic appliance.

Science.gov (United States)

Ehrnrooth, Minna; Kerosuo, Heidi

2009-11-01

Although nickel is the most common cause of contact allergy, nickel-containing orthodontic appliances seldom cause adverse reactions that result in discontinuation of treatment. We report on an eruption of dermatitis in the face and neck of an adult female patient after placement of a rapid maxillary expansion appliance (RME). Because the patient suspected nickel allergy, her tolerance to the appliance material was tested intraorally before treatment by cementing bands on four teeth for a week. No visible adverse reactions were seen during the test. One week after cementation of the RME appliance, the patient reported strong itching of the face and a red rash. Clinical examination showed itchy papular erythema on the face and neck. No intraoral reactions or symptoms were present. The RME appliance was removed, and symptoms disappeared in 4 to 5 days. The patient was referred for a nickel patch test, which gave a strong positive result. Adverse patient reactions of potential allergic origin should be diagnosed carefully, and their possible impact on further treatment should be evaluated accordingly.

An Iterative Load Disaggregation Approach Based on Appliance Consumption Pattern

Directory of Open Access Journals (Sweden)

Huijuan Wang

2018-04-01

Full Text Available Non-intrusive load monitoring (NILM, monitoring single-appliance consumption level by decomposing the aggregated energy consumption, is a novel and economic technology that is beneficial to energy utilities and energy demand management strategies development. Hardware costs of high-frequency sampling and algorithm’s computational complexity hampered NILM large-scale application. However, low sampling data shows poor performance in event detection when multiple appliances are simultaneously turned on. In this paper, we contribute an iterative disaggregation approach that is based on appliance consumption pattern (ILDACP. Our approach combined Fuzzy C-means clustering algorithm, which provide an initial appliance operating status, and sub-sequence searching Dynamic Time Warping, which retrieves single energy consumption based on the typical power consumption pattern. Results show that the proposed approach is effective to accurately disaggregate power consumption, and is suitable for the situation where different appliances are simultaneously operated. Also, the approach has lower computational complexity than Hidden Markov Model method and it is easy to implement in the household without installing special equipment.

Electronic Control System Of Home Appliances Using Speech Command Words

Directory of Open Access Journals (Sweden)

Aye Min Soe

2015-06-01

Full Text Available Abstract The main idea of this paper is to develop a speech recognition system. By using this system smart home appliances are controlled by spoken words. The spoken words chosen for recognition are Fan On Fan Off Light On Light Off TV On and TV Off. The input of the system takes speech signals to control home appliances. The proposed system has two main parts speech recognition and smart home appliances electronic control system. Speech recognition is implemented in MATLAB environment. In this process it contains two main modules feature extraction and feature matching. Mel Frequency Cepstral Coefficients MFCC is used for feature extraction. Vector Quantization VQ approach using clustering algorithm is applied for feature matching. In electrical home appliances control system RF module is used to carry command signal from PC to microcontroller wirelessly. Microcontroller is connected to driver circuit for relay and motor. The input commands are recognized very well. The system is a good performance to control home appliances by spoken words.

Pacific Northwest GridWise™ Testbed Demonstration Projects; Part II. Grid Friendly™ Appliance Project

Energy Technology Data Exchange (ETDEWEB)

Hammerstrom, Donald J.; Brous, Jerry; Chassin, David P.; Horst, Gale R.; Kajfasz, Robert; Michie, Preston; Oliver, Terry V.; Carlon, Teresa A.; Eustis, Conrad; Jarvegren, Olof M.; Marek, W.; Munson, Ryan L.; Pratt, Robert G.

2007-10-01

Fifty residential electric water heaters and 150 new residential clothes dryers were modified to respond to signals received from underfrequency, load-shedding appliance controllers. Each controller monitored the power-grid voltage signal and requested that electrical load be shed by its appliance whenever electric power-grid frequency fell below 59.95 Hz. The controllers and their appliances were installed and monitored for more than a year at residential sites at three locations in Washington and Oregon. The controllers and their appliances responded reliably to each shallow underfrequency event—an average of one event per day—and shed their loads for the durations of these events. Appliance owners reported that the appliance responses were unnoticed and caused little or no inconvenience for the homes’ occupants.

Leaking electricity in domestic appliances

International Nuclear Information System (INIS)

Meier, Alan; Rosen, Karen

1999-01-01

Many types of home electronic equipment draw electric power when switched off or not performing their principal functions. Standby power use (or ''leaking electricity'') for most appliances ranges from 1 - 20 watts. Even though standby use of each device is small, the combined standby power use of all appliances in a home can easily exceed 50 watts. Leaking electricity is already responsible for 5 to 10 percent of residential electricity use in the United States and over 10 percent in Japan. An increasing number of white goods also have standby power requirements. There is a growing international effort to limit standby power to around one watt per device. New and existing technologies are available to meet this target at little or no extra cost

Real-time identification of residential appliance events based on power monitoring

Science.gov (United States)

Yang, Zhao; Zhu, Zhicheng; Wei, Zhiqiang; Yin, Bo; Wang, Xiuwei

2018-03-01

Energy monitoring for specific home appliances has been regarded as the pre-requisite for reducing residential energy consumption. To enhance the accuracy of identifying operation status of household appliances and to keep pace with the development of smart power grid, this paper puts forward the integration of electric current and power data on the basis of existing algorithm. If average power difference of several adjacent cycles varies from the baseline and goes beyond the pre-assigned threshold value, the event will be flagged. Based on MATLAB platform and domestic appliances simulations, the results of tested data and verified algorithm indicate that the power method has accomplished desired results of appliance identification.

Colostomies and the use of colostomy appliances.

Science.gov (United States)

Cronin, Elaine

The surgical formation of a colostomy is indicated as part of the treatment of various conditions, primarily colon cancer, requiring the patient (ostomist) to wear a colostomy pouch. Today's stoma appliances bear no resemblance to those worn three or four decades ago when colostomy, ileostomy and urostomy bags were made entirely from rubber. The patient, who would have two to three bags in circulation at a time, would interchange them allowing for the washing and drying of the previous one, thus minimizing odour and potential perishing of the rubber. The design of these appliances was simple, but they were large and bulky and the outlet resembled that of a hot-water bottle stopper or a cap from an old soda bottle that required the insertion of coinage (2p) to open it. This article explores the range of colostomy appliances and management options available to the nurse when caring for patients with a colostomy.

Pyogenic granuloma: a rare side complication from an orthodontic appliance.

Science.gov (United States)

Acharya, Priti N; Gill, Daljit; Lloyd, Tim

2011-12-01

This case report discusses a rare side effect associated with the use ofa fixed quad helix orthodontic appliance. A 14-year-old healthy girl presented with a painful enlarging mass on her tongue, which was causing distress to both her and her parents. Investigations confirmed that the mass was a pyogenic granuloma and management involved surgical excision of the mass and removal of the quad helix appliance. At least once previous case associated with an orthodontic quad helix appliance has been reported in the literature.

Performance of a Solar Heating System with Photovoltaic Thermal Hybrid Collectors and Heat Pump

DEFF Research Database (Denmark)

Dannemand, Mark; Furbo, Simon; Perers, Bengt

2017-01-01

. When the solar collectors are unable to supply the heat demand an auxiliary heat source is used. Heat pumps can generate this heat. Liquid/water heat pumps have better performance than air/water heat pumps in cold climates but requires installation of a tubing system for the cold side of the heat pump....... The tubes are typically placed in the ground, requires a significant land area and increase the installation cost. A new system design of a solar heating system with two storage tanks and a liquid/water heat pump is presented. The system consists of PVT collectors that generate both heat and electricity......The energy consumption in buildings accounts for a large part of the World’s CO2 emissions. Much energy is used for appliances, domestic hot water preparation and space heating. In solar heating systems, heat is captured by solar collectors when the sun is shining and used for heating purposes...

33 CFR 81.20 - Lights and sound signal appliances.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights and sound signal appliances. 81.20 Section 81.20 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... appliances. Each vessel under the 72 COLREGS, except the vessels of the Navy, is exempt from the requirements...

An application of the gas-fired chilling and heating units to domestic houses

Energy Technology Data Exchange (ETDEWEB)

Choi, J.H.; Yang, Y.M.; Chae, J.M.; Bang, H.S.; Kwon, O.B.; Yoo, S.I.; Kim, T.H. [R and D Center, Korea Gas Co. (Korea); Lee, T.W.; Kim, T.H.; Kim, B.H.; Hwang, I.J.; Kim, J.Y.; Kim, C.D.; Park, S.J. [Korea Institute of Construction Technology (Korea)

1999-10-01

Following researches and considerations were performed in this study for an efficient application of gas-fired chilling and heating units to the residential buildings. (1) Status of domestic cooling and heating for residential building. (2) Various introduction schemes of outdoor unit. (3) Design exclusive area for the gas appliance and installation of it. (4) Ventilation of exhaust gas and heat. (5) Prepare the installation specifications or standards for gas-fired chilling and heating units. (6) Design technique of plumbing for cooling and heating. (7) Evaluation of unit's capacity considering the thermal load of domestic buildings. (8) Cooling and heating system with the unit. (9) Fundamental test for evaluation of applicability. (10) Actual design and construction of experimental house for an application and a demonstration of the developed gas units. (11) Field test for cooling and heating. (12) Evaluation of economic efficiency. (13) Establish a business potential. (14) Establishment of legal and systematic support, energy rate. (15) Troubleshooting in the course of development and application of the new gas appliance. 41 refs., 214 figs., 52 tabs.

Effect of thermoplastic appliance thickness on initial stress distribution in periodontal ligament

Directory of Open Access Journals (Sweden)

De-Shin Liu

2015-04-01

Full Text Available A numerical investigation into the initial stress distribution induced within the periodontal ligament by thermoplastic appliances with different thicknesses is performed. Based on the plaster model of a 25-year-old male patient, a finite element model of the maxillary lateral incisors and their supporting structures is constructed. In addition, four finite element models of thermoplastic appliances with different thicknesses in the range of 0.5–1.25 mm are also constructed based on the same plaster model. Finite element analysis simulations are performed to examine the effects of the force delivered by the thermoplastic appliances on the stress response of the periodontal ligament during the elastic recovery process. The results show that the stress induced in the periodontal ligament increases with an increasing appliance thickness. For example, the stress triples from 0.0012 to 0.0038 MPa as the appliance thickness is increased from 0.75 to 1.25 mm. The results presented in this study provide a useful insight into as a result of the compressive and tensile stresses induced by thermoplastic appliances of different thicknesses. Moreover, the results enable the periodontal ligament stress levels produced by thermoplastic appliances of different thicknesses to be reliably estimated.

Analyzing price and efficiency dynamics of large appliances with the experience curve approach

International Nuclear Information System (INIS)

Weiss, Martin; Patel, Martin K.; Junginger, Martin; Blok, Kornelis

2010-01-01

Large appliances are major power consumers in households of industrialized countries. Although their energy efficiency has been increasing substantially in past decades, still additional energy efficiency potentials exist. Energy policy that aims at realizing these potentials faces, however, growing concerns about possible adverse effects on commodity prices. Here, we address these concerns by applying the experience curve approach to analyze long-term price and energy efficiency trends of three wet appliances (washing machines, laundry dryers, and dishwashers) and two cold appliances (refrigerators and freezers). We identify a robust long-term decline in both specific price and specific energy consumption of large appliances. Specific prices of wet appliances decline at learning rates (LR) of 29±8% and thereby much faster than those of cold appliances (LR of 9±4%). Our results demonstrate that technological learning leads to substantial price decline, thus indicating that the introduction of novel and initially expensive energy efficiency technologies does not necessarily imply adverse price effects in the long term. By extending the conventional experience curve approach, we find a steady decline in the specific energy consumption of wet appliances (LR of 20-35%) and cold appliances (LR of 13-17%). Our analysis suggests that energy policy might be able to bend down energy experience curves. (author)

Abolir les obstacles que constituent les frais de santé : les ...

International Development Research Centre (IDRC) Digital Library (Canada)

10 juin 2016 ... Abolir les obstacles que constituent les frais de santé : les ... Le financement des services de santé repose sur un système de ... Dans les années 1980, conformément aux recommandations d'organismes internationaux, ...

Les jeux de hasard chez les enfants et les adolescents

Science.gov (United States)

Gupta, Rina; Pinzon, Jorge L

2012-01-01

RÉSUMÉ Même si, au Canada, les mineurs n’ont pas le droit de jouer à des jeux de hasard légalisés, les adolescents participent souvent à des jeux de hasard soit légalisés (produits de loterie, casino, terminaux de jeux vidéo), soit autonomes (jeux de cartes, paris sportifs, dés) à la maison et en milieu scolaire. Chez les adultes, le taux de prévalence de dépendance aux jeux de hasard au cours de la vie se situe entre 1 % et 2 %. D’après les données existantes, la prévalence chez les adolescents serait de deux à quatre fois plus élevée. On ne sait pas grand-chose des facteurs de risque d’apparition et de perpétuation d’une dépendance pathologique aux jeux de hasard. Le présent document de principes vise à informer les pédiatres, les médecins de famille et les autres professionnels de la santé des connaissances émergentes sur les jeux de hasard pendant l’enfance et l’adolescence et du risque de conséquences graves qui s’y rattachent. On y exhorte également les gouvernements fédéral, provinciaux et territoriaux à inclure cette question dans leur programme et à tenir compte des facteurs sociopolitiques associés aux jeux de hasard.

Incorporating experience curves in appliance standards analysis

International Nuclear Information System (INIS)

Desroches, Louis-Benoit; Garbesi, Karina; Kantner, Colleen; Van Buskirk, Robert; Yang, Hung-Chia

2013-01-01

There exists considerable evidence that manufacturing costs and consumer prices of residential appliances have decreased in real terms over the last several decades. This phenomenon is generally attributable to manufacturing efficiency gained with cumulative experience producing a certain good, and is modeled by an empirical experience curve. The technical analyses conducted in support of U.S. energy conservation standards for residential appliances and commercial equipment have, until recently, assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. This assumption does not reflect real market price dynamics. Using price data from the Bureau of Labor Statistics, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These experience curves were incorporated into recent energy conservation standards analyses for these products. Including experience curves increases the national consumer net present value of potential standard levels. In some cases a potential standard level exhibits a net benefit when considering experience, whereas without experience it exhibits a net cost. These results highlight the importance of modeling more representative market prices. - Highlights: ► Past appliance standards analyses have assumed constant equipment prices. ► There is considerable evidence of consistent real price declines. ► We incorporate experience curves for several large appliances into the analysis. ► The revised analyses demonstrate larger net present values of potential standards. ► The results imply that past standards analyses may have undervalued benefits.

Assessment of Literature Related to Combustion Appliance Venting Systems

Energy Technology Data Exchange (ETDEWEB)

Rapp, Vi H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stratton, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-06-01

In many residential building retrofit programs, air tightening to increase energy efficiency is constrained by concerns about related impacts on the safety of naturally vented combustion appliances. Tighter housing units more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spillage. Several test methods purportedly assess the potential for depressurization-induced backdrafting and spillage, but these tests are not robustly reliable and repeatable predictors of venting performance, in part because they do not fully capture weather effects on venting performance. The purpose of this literature review is to investigate combustion safety diagnostics in existing codes, standards, and guidelines related to combustion appliances. This review summarizes existing combustion safety test methods, evaluations of these test methods, and also discusses research related to wind effects and the simulation of vent system performance. Current codes and standards related to combustion appliance installation provide little information on assessing backdrafting or spillage potential. A substantial amount of research has been conducted to assess combustion appliance backdrafting and spillage test methods, but primarily focuses on comparing short-term (stress) induced tests and monitoring results. Monitoring, typically performed over one week, indicated that combinations of environmental and house operation characteristics most conducive to combustion spillage were rare. Research, to an extent, has assessed existing combustion safety diagnostics for house depressurization, but the objectives of the diagnostics, both stress and monitoring, are not clearly defined. More research is also needed to quantify the frequency of test “failure” occurrence throughout the building stock and assess the statistical effects of weather (especially wind) on house depressurization and in turn on combustion appliance venting

21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

Science.gov (United States)

2010-04-01

... appliances and accessories. 888.3030 Section 888.3030 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

46 CFR 199.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... appliances and arrangements. 199.40 Section 199.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS General § 199.40 Evaluation, testing and approval of lifesaving appliances and arrangements. (a) Each item of...

Convex stoma appliances: an audit of stoma care nurses.

Science.gov (United States)

Perrin, Angie

2016-12-08

This article observes the complexities surrounding the use of convex appliances within the specialist sphere of stoma care. It highlights some of the results taken from a small audit carried out with 24 stoma care nurses examining the general use of convex appliances and how usage of convex products has evolved, along with specialist stoma care practice.

Dual capillary tube / heat exchanger in combination with cycle priming for reducing charge migration

Science.gov (United States)

Gomes, Alberto Regio; Kuehl, Steven J.; Litch, Andrew D.; Wu, Guolian

2017-07-04

A refrigerator appliance including a multi-capacity compressor and a refrigerant circuit with two conduits and pressure reducing devices arranged in parallel between an evaporator and a condenser. Refrigerant can flow through one, both or none of the conduits and pressure reducing devices. The appliance also has a heat exchanger in contact with either one pressure reducing device, or one conduit between the pressure reducing device and the valve system. The appliance also includes a controller for priming the compressor above a nominal capacity for a predetermined or calculated duration at the beginning of an ON-cycle.

Survival of palatal miniscrews used for orthodontic appliance anchorage: a retrospective cohort study.

Science.gov (United States)

Karagkiolidou, Angeliki; Ludwig, Björn; Pazera, Pawel; Gkantidis, Nikolaos; Pandis, Nikolaos; Katsaros, Christos

2013-06-01

The purpose of this study was to examine the overall success of miniscrews inserted in the paramedian palatal region for support of various appliances during orthodontic treatment. The patients received 1 or 2 miniscrews in the paramedian anterior palate of 8.0-mm length and 1.6-mm diameter placed during orthodontic treatment by the same experienced orthodontist. In total, 196 patients (121 girls, 75 boys; median age, 11.7; interquartile range, 3.7) who received 384 miniscrews were evaluated. Two hundred four miniscrews were used with rapid palatal expansion appliances, 136 with appliances for distalization of posterior teeth, and 44 with other appliances, such as transpalatal arches for tooth stabilization. The overall survival of the miniscrews was excellent (97.9%) in the cases examined. Cox regression analysis showed no difference in the overall survival rates of miniscrews loaded with different appliances for sex (hazard ratio, 0.95; 95% confidence interval, 0.71-1.27; P = 0.73) after adjusting for appliance and age. This study shows that miniscrews placed in the paramedian anterior palate for supporting various orthodontic appliances have excellent survival. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Modelling the effects of U.S. ENERGY STARR appliance programs

International Nuclear Information System (INIS)

Feldman, Shel; Hoefgen, Lynn; Wilson-Wright, Lisa; Li, Angela

2005-01-01

Numerous U.S. utilities and market transformation organizations have invested heavily in the ENERGY STAR program, designed to increase market penetration of energy-efficient products (e.g., home appliances, lighting products, windows). Major activities involve stimulating production and promotion of qualifying models, as well as stocking, sales support and financial incentives to customers-all of which entail considerable investments of public funds. Several studies have shown that customer awareness of ENERGY STAR has increased across the country, particularly where energy-efficiency programs have been most active. Furthermore, studies in regions with aggressive programs have shown that the market penetration of qualifying products has increased rapidly. Until recently, however, policy makers have lacked reliable studies that compare changes in market penetration across regions with and without programs while factoring out effects of demographic and other background factors (e.g., education, income, and climate). Also lacking have been attempts to assess whether heavy promotion of the ENERGY STAR brand with some appliances (e.g., clothes washers) has affected the market penetration of less-promoted qualifying appliances. In this paper, the authors address these issues, using a database of the market penetration of four major home appliances at national retailers in each of the individual states over a multi-year period, based on multivariate statistical models. Results include both analyses of the overall trend of market penetration (1998-2002) for the appliances considered and the incremental effects of the 2003 program. The results lead to recommendations regarding the design of programs supporting ENERGY STAR compliant appliances and the key components of those programs

File System Virtual Appliances

Science.gov (United States)

2010-05-01

4 KB of data is read or written, data is copied back and forth using trampoline buffers — pages that are shared during proxy initialization — because...in 2008. CIO Magazine. 104 · File system virtual appliances [64] Megiddo, N. and Modha, D. S. 2003. ARC: A Self-Tuning, Low Over- head Replacement

Economical regulation power through load shifting with smart energy appliances

NARCIS (Netherlands)

Vlot, M.C.; Knigge, J.D.; Slootweg, J.G.

2013-01-01

This paper considers the technical and economical feasibility of the introduction of automated demand response from domestic smart appliances in a European setting as a means to create a significant amount of regulating power. Simplified power-time flexibility models for appliances are introduced on

Treatment of obstructive sleep apnea patients using oral appliances--our experiences.

Science.gov (United States)

Miljus, Dusan; Tihacek-Sojić, Ljiljana; Milić-Lemić, Aleksandra; Andjelković, Marko

2014-07-01

Obstructive sleep apnea (OSA) is one of the most prevalent sleep disorders. It is recognized as a serious risk factor for car and workplace accidents due to daytime sleepiness, and factor for coronary heart diseases and stroke. The aim of this study was to examine the effectiveness of oral appliances for mandibular advance in treating mild to moderate OSA. A total of 15 patients were included in this study, all diagnosed with mild or moderate OSA. Oral appliances were custom made for each patient in protrusive position at 50% of maximum mandibular advancement. The patients were given instructions not to sleep on their backs and avoid alcohol consumption during the study as these are the factors that can contribute to symptoms progression. Complete and partial treatment success was achieve in 14 of the patients. Apnea-hypopnea index values were significantly lower (p appliances has proven successful. Patients were comfortable using oral appliances and were ready to wear them for prolonged period of time. Use of oral appliances is very common in the world and should not be discarded. They are also very comfortable, practical and affordable comparing to continuous positive airway pressure (CPAP) apparatus, not to mention surgery. Use of oral appliances is safe and very well tolerated, and ought to be offered to patients with OSA.

46 CFR 133.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

Science.gov (United States)

2010-10-01

... appliances and arrangements. 133.40 Section 133.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... lifesaving appliances and arrangements. (a) Each item of lifesaving equipment required by this part to be... OCMI for use on the OSV. (c) The Commandant (CG-521) may accept a novel lifesaving appliance or...

14 CFR 21.617 - Issue of letters of TSO design approval: import appliances.

Science.gov (United States)

2010-01-01

...: import appliances. 21.617 Section 21.617 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Order Authorizations § 21.617 Issue of letters of TSO design approval: import appliances. (a) A letter of TSO design approval may be issued for an appliance that is manufactured in a foreign country with...

Switch green : Energy Star appliance feebate

International Nuclear Information System (INIS)

2007-01-01

Between 1990 and 2004, greenhouse gas (GHG) emissions from the residential sector have grown by 10 per cent, and are likely to continue growing unless a policy aimed at reducing emissions is introduced. The residential sector is a significant contributor to Canada's overall GHG emissions, and an important source for potential reductions. This report presented the results of a study that described and evaluated a new economic instrument aimed at reducing greenhouse gas (GHG) emissions and energy consumption in Canada from household appliances, such as air conditioners, furnaces and boilers. Results of a quantitative analysis to determine the effect of changing taxation of residential appliances to reflect energy consumption and greenhouse gas emissions were presented. In addition, the report presented the results of a qualitative evaluation of the policy, using the criteria established in the 2005 budget plan, a framework for evaluating environmental tax proposals. The report outlined the context for the tax proposal that was evaluated and provided a summary of trends in Canada's greenhouse gas emissions and energy consumption as well as a discussion of important trends in residential energy consumption. A review of policies already in place to address energy consumption from household appliances was also presented. 11 tabs., 6 figs

46 CFR 130.220 - Design of equipment for cooking and heating.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Design of equipment for cooking and heating. 130.220... Design of equipment for cooking and heating. (a) Doors on each cooking appliance must be provided with heavy-duty hinges and locking-devices to prevent accidental opening in heavy weather. (b) Each cooking...

Improvements in appliance holders

International Nuclear Information System (INIS)

Chapman, J.E.

1977-01-01

Reference is made to appliance holders for locating tools, instruments, etc. in operative relationship to workpieces and accessible through passageways of restricted transverse dimensions. The appliance holder described comprises an elongated external frame provided with transversely, outwardly expanding frictional gripping means in two longitudinally spaced sets and with a ring of spur teeth. An inner elongated frame is held within the external frame in two longitudinally spaced rotary bearings and carries a spur wheel which engages the ring of the spur teeth. A motor is arranged to rotate the spur wheel and hence the inner frame in relation to the external frame. A carriage is carried by the inner frame, longitudinally movable by a motor in relation thereto, and a further carriage is mounted on this first carriage. This second cariage is transversely movable in relation to the inner frame and is provided with a face plate for attachment of tools, instruments, etc. A motor is mounted on the first carriage for moving the second carriage. (U.K.)

76 FR 79057 - Appliance Labeling Rule

Science.gov (United States)

2011-12-21

... Part 305 Advertising, Energy conservation, Household appliances, Labeling, Reporting and recordkeeping... emitting diode (OLED) means a thin-film light- emitting device that typically consists of a series of...

Pompes à chaleur dans l'industrie Heat Pumps in Industry

Directory of Open Access Journals (Sweden)

Benchecroun N.

2006-11-01

Full Text Available Les pompes à chaleur pourraient permettre une réduction de la consommation énergétique de l'industrie française estimée à 3,5 Mtep à l'horizon 1990 (300 000 tep en 1982. Ces installations se situeront dans les domaines du chauffage des locaux industriels, du séchage à basse température, du réchauffage de liquides et de certaines opérations de fractionnement. Pour les utilisations dans des procédés industriels les secteurs concernés sont principalement les industries agroalimentaires et, à plus long terme, celui de la chimie (y compris pétrochimie. On constate que les ventes de machines de forte puissance restent faibles (environ 500 de 1973 à 1982. Le climat général d'investissement, la nécessité d'adapter les procédés à l'utilisation d'une pompe à chaleur, et le faible niveau de température Heat pumps could be used to reduce energy consumption by French industry which may attain 3. 5 million tOE by 1990 (300 000 tOE in 1982. Such installations will be used in the fields of industrial space heating, low-temperature drying, the heating of liquids and various fractionating operations. For uses in industrial processes, the sectors involved are mainly agribusiness and food industries and, in the longer range, the chemical industry (including petrochemicals. Sales of high-powered machinery are still low (about 500 from 1973 to 1982. The general investment climate, the need to adapt processes to the use of heat pumps, and the low temperature level (< 120 °C of the heat delivered are the main factors holding back the penetration of this type of equipment in industry. The use of a nonazeotropic mixture of fluids (particularly hydrocarbons gives compression heat pumps a flexibility of adaptation which should help remove these technicalobstacles and thus make it easier for heat pumps to penetrate, especially in the chemical sector.

Forced heat convection in annular spaces; Convection forcee de la chaleur dans les espaces annulaires

Energy Technology Data Exchange (ETDEWEB)

Pelce, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1960-02-15

This report deals with the experimental study of forced heat convection in annular spaces through which flow of air is passing when a uniform heat flux is dissipated across the inner wall. These observations took place chiefly in the region where thermal equilibrium are not yet established. Amongst other things it became apparent that, both in the region where thermal equilibrium conditions are on the way to establishment and where they are already established, the following relationship held good: the longitudinal temperature gradient, either on the wall or in the fluid stream, is proportional to the heat flux dissipated q, and inversely proportional to the average flow rate V: dT/dx = B (q/V). From this result the next step is to express the variations of the local convection coefficient {alpha} (or of the Margoulis number M) in a relationship of the form: 1/M = {psi}(V) + F(x). If this relationship is compared with the classical empirical relationship {alpha} = KV{sup n} (where n is close to 0.8), the relationship: 1/M = {xi}V{sup 1-n} + F(x) is obtained ({xi} is a constant for a given annular space); from this it was possible to coordinate the whole set of experimental results. (author) [French] Il s'agit precisement de l'etude experimentale de la convection forcee de la chaleur dans des espaces annulaires parcourus par de l'air en ecoulement turbulent, lorsqu'on dissipe a travers la paroi interieure un flux de chaleur uniforme. Ces observations ont eu lieu principalement dans la region ou le regime thermique n'est pas encore etabli. Il est apparu, entre autre, qu'il existait, tant dans la region ou le regime thermique est en voie d'etablissement qu'en regime etabli, la relation suivante: le gradient longitudinal des temperatures, que ce soit sur la paroi ou dans l'ecoulement fluide, est proportionnel au flux de la chaleur dissipee q, et inversement proportionnel a la vitesse moyenne V de l'ecoulement: dT/dx = B (q/V). Ce resultat a pour consequence de traduire

Class II malocclusion treatment using combined Twin Block and fixed orthodontic appliances – A case report

Science.gov (United States)

Al-Anezi, Saud A.

2010-01-01

The effect of the Twin Block functional orthodontic appliances is mostly dento-alveolar with small skeletal effect. There are certain clinical indications where functional appliances can be used successfully in class II malocclusion e.g. in a growing patient. The use of these appliances is greatly dependent on the patient’s compliance and they simplify the fixed appliance phase. In this case, a 13-year old adolescent was treated with Twin Block appliance followed by fixed appliance to detail the occlusion. The design and treatment effects were demonstrated in this case report. PMID:24151413

Routines for interocclusal appliance therapy among general dental practitioners in a Swedish county.

Science.gov (United States)

Gnauck, Maja; Helkimo, Martti; Magnusson, Tomas

2012-01-01

The aims of this study were to investigate what kind of interocclusal appliances that were chosen among Swedish dentists when treating temporomandibular disorders (TMD), the clinical rationale for the treatment, the diagnoses that warranted the appliance treatment, the use of adjunct TMD treatments and prognostic considerations, and possible differences in these respects between children/adolescents and adults with TMD, and, finally, possible differences between private practitioners and general practitioners in the public dental service. During the 12-months-period April 2009-March 2010 all general dental practitioners in the county of Jönköping, Sweden, were asked to fill in a questionnaire when performing a TMD treatment with an interocclusal appliance. A total of 394 questionnaires were filled in and returned, 216 (55%) from dentists in public dental service and 178 (45%) from private practitioners. It was found that in 40% of the cases, no pre-treatment recording of the functional status in the masticatory system had been made. The commonest reasons for the treatment were bruxism, headache, and replacement of a previous appliance. Less than half of the appliances made were hard acrylic appliances. Some kind of adjunct therapy had been made in 22% of the cases treated in public dental service. The corresponding figure for those treated by private practitioners was 25%. Therapeutic jaw exercises was the commonest adjunct therapy followed by selective occlusal adjustment. In the vast majority of cases, the dentists judged the prognosis of the treatment to be good. It is concluded that a large number of appliances made to treat TMD were soft appliances, especially in public dental service. This reflects a possible overuse of soft appliances at the expense of hard acrylic appliances. Furthermore, in a large number of cases, the treatment was performed without any pre-treatment registrations, and adjunct therapies were rarely used. In all these respects,there is

Assessment of Human Exposure to Magnetic Fields Produced by Domestic Appliances (invited paper)

International Nuclear Information System (INIS)

Preece, A.W.; Kaune, W.T.; Grainger, P.; Golding, J.

1999-01-01

A study of 50 homes and their appliances examined whether a detailed appliance-use questionnaire and survey would yield data comparable with direct personal monitoring. This was coupled with direct measurement of the appliances in use to determine the field at 50 cm and 1 m. The findings were that individual time-weighted average (TWA) exposures calculated from questionnaire and activity diaries in conjunction with the appliance magnetic field were unrelated to actual personal exposure measurement. It was concluded that questionnaires are of little or no value for TWA estimation. However, peak exposure and short-term temporal variability could be modelled in subjects spending at least 15 min per day within 1 m of an operating microwave cooker or conventional cooker. This method could be extended to other appliances. (author)

Treatment with active orthodontic appliance in adult patient

OpenAIRE

Radeska, Ana; Radeski, Josif; Zlatanovska, Katerina; Papakoca, Kiro; Zarkova, Julija

2012-01-01

Aim: Showing the efficiency of orthodontic mobile appliance in treatment of adult patient Case summary: The patient A.K. Age 25 years whit forced progenia, bilateral hypodontia of the maxillary incisors and cross bite of 2 mm in front. The patient was treated with active orthodontic appliance whit bitten ridge and down labial arch. The treatment lasted 18 months after which periods is reached normal occlusion with normal overlap in front and closed diastema mediana. The hypodontia of the m...

LES of fluid and heat flow over a wall-bounded short cylinder at different inflow conditions

Energy Technology Data Exchange (ETDEWEB)

Borello, D [Dipartmento di Ingegneria Meccanica e Aerospaziale, Sapienza University of Rome (Italy); Hanjalic, K, E-mail: borello@dma.ing.uniroma1.it [Department of Multi-scale Physics, Delft University of Technology (Netherlands)

2011-12-22

We report on LES studies of flow patterns, vortical structures and heat transfer in flows over a short single cylinder of diameter D placed in a plane channel of height h = 0.4D in which the bottom wall is heated. The Reynolds number of 6150, based on D, corresponds to the water experiments reported by Sahin et al. (2008). For the basic computational domain of 24 Multiplication-Sign 14 Multiplication-Sign 0.4D three different inflow conditions have been considered: a non-turbulent flow with a uniform initial velocity developing along the channel (NT), a fully developed channel flows (FD) (generated a priori) and periodic conditions (PC). The latter boundary conditions have also been considered for two shorter domain lengths of 6D and 3D corresponding to a cylinder in a compact matrix. For the long domain, despite the length of the channel of 9.5 D before (and after) the cylinder, the inlet conditions show strong effects on the formation and evolution of the multiple vortex systems both in front and behind the cylinder, influencing significantly also friction and heat transfer. Simulations show some agreement with experimental data though the comparison is impaired by the uncertainty in the experimental inflow conditions. For the shortest cylinder spacing the wake never closes and the flow shows enhanced unsteadiness and turbulence level. Interestingly, the comparison for the same short domain (3Dx3D) using the mean temperature at the inflow to this domain as a reference shows the lowest average base-wall Nusselt number in the PC 3D case that corresponds to compact heat exchangers.

Home Appliances as Home Controllers: Concepts and Set-Top Box Implementation

Directory of Open Access Journals (Sweden)

Z. Jovanovic

2010-11-01

Full Text Available In this paper we present a novel softwarebased home control platform suitable as an extension to digital home appliances that are equipped with a CPU (settop boxes, home theatre systems, TV sets, gaming consoles, etc. By using an appliance they are already accustomed to, users become able to control lights, appliances and media playback in their homes. Intelligence and awareness are achieved with a support for execution of recipes – preprepared scripts that define timely actions and respond to triggers obtained from sensors. Software abstraction layer facilitates integration of any desired communication protocol. In our prototype, we supported Zigbee and DMX for light control, X10 for light/appliances control over power line, as well as Ethernet-based optical cameras as motion/presence sensors and UPnP/DLNA based equipment for distributed media playback.

Emissions from SF6 appliances in Norway. Additional report No. 2

International Nuclear Information System (INIS)

Gjarede, Anne Cathrine

1999-01-01

The report presents facts regarding the Norwegian SF 6 emissions and the significance for the Norwegian climatic gas accounts in order to evaluate whether 12-24 kV SF 6 appliances are environmentally acceptable. Estimations show that emissions from such equipment contribute with about 0.2 % of the total Norwegian CO 2 emissions in 1993. The SF 6 which is stored in electric appliances, may either be recycled or decomposed to more environmentally acceptable end products. The report concludes that the contribution to the greenhouse effects from SF 6 appliances is minimal

Treatment of cooling appliances. Interrelations between environmental protection, resource conservation, and recovery rates

International Nuclear Information System (INIS)

Laner, David; Rechberger, Helmut

2007-01-01

The treatment of cooling appliances in Austria is primarily influenced by two factors. On the one hand is their changing composition and on the other hand the ordinance on Waste Prevention, Collection and Treatment of Waste Electrical and Electronic Equipment (WEEE ordinance), which stipulates a minimum recycling rate of 75% for cooling appliances. This paper investigates whether this recycling rate leads to optimal treatment practices for cooling appliances with respect to resource conservation and environmental protection. Two different treatment technologies which achieve recycling rates between 50-60% and 80-90%, respectively, are compared both for cooling appliances containing Chlorofluorocarbons (CFCs) and for appliances containing Volatile Organic Compounds (VOC). Materials and energy balances are developed for each model. To evaluate resource consumption, expenditures as well as savings of energy and materials are incorporated via the Cumulative Energy Demand (CED). In order to analyse the environmental impact of the different practices, balances for CFC, CO 2 , HF, HCl and solid residues are established. The results show that the treatment type aiming for a maximum of materials recycling contributes more to resource conservation than the other treatment type. But for CFC appliances the former is associated with substantial CFC emissions, which turn out to be most relevant when treating these appliances. Generally, it is found that the optimum recycling rate is a function of the composition of the appliance and the technologies applied, both in recycling and in primary production. A high recycling rate per se does not automatically result in an optimal solution with regard to resource conservation and environmental protection. (author)

Effects of mechanical properties of thermoplastic materials on the initial force of thermoplastic appliances.

Science.gov (United States)

Kohda, Naohisa; Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Ahluwalia, Karamdeep S; Mizoguchi, Itaru

2013-05-01

To measure the forces delivered by thermoplastic appliances made from three materials and investigate effects of mechanical properties, material thickness, and amount of activation on orthodontic forces. Three thermoplastic materials, Duran (Scheu Dental), Erkodur (Erkodent Erich Kopp GmbH), and Hardcast (Scheu Dental), with two different thicknesses were selected. Values of elastic modulus and hardness were obtained from nanoindentation measurements at 28°C. A custom-fabricated system with a force sensor was employed to obtain measurements of in vitro force delivered by the thermoplastic appliances for 0.5-mm and 1.0-mm activation for bodily tooth movement. Experimental results were subjected to several statistical analyses. Hardcast had significantly lower elastic modulus and hardness than Duran and Erkodur, whose properties were not significantly different. Appliances fabricated from thicker material (0.75 mm or 0.8 mm) always produced significantly greater force than those fabricated from thinner material (0.4 mm or 0.5 mm). Appliances with 1.0-mm activation produced significantly lower force than those with 0.5-mm activation, except for 0.4-mm thick Hardcast appliances. A strong correlation was found between mechanical properties of the thermoplastic materials and force produced by the appliances. Orthodontic forces delivered by thermoplastic appliances depend on the material, thickness, and amount of activation. Mechanical properties of the polymers obtained by nanoindentation testing are predictive of force delivery by these appliances.

Design and manufacturing of patient-specific orthodontic appliances by computer-aided engineering techniques.

Science.gov (United States)

Barone, Sandro; Neri, Paolo; Paoli, Alessandro; Razionale, Armando Viviano

2018-01-01

Orthodontic treatments are usually performed using fixed brackets or removable oral appliances, which are traditionally made from alginate impressions and wax registrations. Among removable devices, eruption guidance appliances are used for early orthodontic treatments in order to intercept and prevent malocclusion problems. Commercially available eruption guidance appliances, however, are symmetric devices produced using a few standard sizes. For this reason, they are not able to meet all the specific patient's needs since the actual dental anatomies present various geometries and asymmetric conditions. In this article, a computer-aided design-based methodology for the design and manufacturing of a patient-specific eruption guidance appliances is presented. The proposed approach is based on the digitalization of several steps of the overall process: from the digital reconstruction of patients' anatomies to the manufacturing of customized appliances. A finite element model has been developed to evaluate the temporomandibular joint disks stress level caused by using symmetric eruption guidance appliances with different teeth misalignment conditions. The developed model can then be used to guide the design of a patient-specific appliance with the aim at reducing the patient discomfort. At this purpose, two different customization levels are proposed in order to face both arches and single tooth misalignment issues. A low-cost manufacturing process, based on an additive manufacturing technique, is finally presented and discussed.

Treatment effects of the Jasper Jumper and the Bionator associated with fixed appliances.

Science.gov (United States)

Neves, Leniana Santos; Janson, Guilherme; Cançado, Rodrigo Hermont; de Lima, Karina Jerônimo Rodrigues Santiago; Fernandes, Thaís Maria Freire; Henriques, José Fernando Castanha

2014-01-01

The aim of this study was to evaluate the effects of Class II malocclusion treatment with the Jasper Jumper and the Bionator, associated with fixed appliances. The sample comprised 77 young individuals divided into 3 groups: Group 1 consisted of 25 patients treated with the Jasper Jumper appliance associated with fixed appliances for a mean period of 2.15 years; group 2 had 30 patients, treated with the Bionator and fixed appliances, for a mean treatment time of 3.92 years; and the control group included 22 subjects followed for a mean period of 2.13 years. The initial and final lateral cephalograms of the patients were evaluated. Intergroup comparison at the initial stage and of the treatment changes were performed by analysis of variance. Their effects consisted in a restrictive effect on the maxilla, a slight increase in anterior face height, retrusion and extrusion of the maxillary incisors, labial tipping and protrusion of the mandibular incisors in both groups and intrusion with the Jasper Jumper appliance, maxillary molar distalization with the Jasper Jumper, extrusion and mesialization of the mandibular molars, both appliances provided significant improvement of the maxillomandibular relationship, overjet, overbite and molar relationship. The effects of both appliances in class II malocclusion treatment are similar; however, treatment with the Jasper Jumper was shorter than with the Bionator.

Do soft drinks affect metal ions release from orthodontic appliances?

Science.gov (United States)

Mikulewicz, Marcin; Wołowiec, Paulina; Loster, Bartłomiej W; Chojnacka, Katarzyna

2015-01-01

The effect of orange juice and Coca Cola(®) on the release of metal ions from fixed orthodontic appliances. A continuous flow system designed for in vitro testing of orthodontic appliances was used. Orange juice/Coca Cola(®) was flowing through the system alternately with artificial saliva for 5.5 and 18.5h, respectively. The collected samples underwent a multielemental ICP-OES analysis in order to determine the metal ions release pattern in time. The total mass of ions released from the appliance into orange juice and Coca Cola(®) (respectively) during the experiment was calculated (μg): Ni (15.33; 37.75), Cr (3.604; 1.052), Fe (48.42; ≥ 156.1), Cu (57.87, 32.91), Mn (9.164; 41.16), Mo (9.999; 30.12), and Cd (0.5967; 2.173). It was found that orange juice did not intensify the release of metal ions from orthodontic appliances, whereas Coca Cola(®) caused increased release of Ni ions. Copyright © 2015 Elsevier GmbH. All rights reserved.

Les manifestations cardiovasculaires chez les hemodialyses ...

African Journals Online (AJOL)

Le but de l'étude est d'analyser sur une période de 12 mois chez 75 patients en hémodialyse chronique, âgés de 38ans en moyenne, le les aspects cliniques, thérapeutiques et évolutifs des manifestations cardiovasculaires. La prévalence est de 87,20% chez les patients. Les signes fonctionnels les plus fréquents sont la ...

What to Do If Your Appliances Are Wet After a Disaster

Centers for Disease Control (CDC) Podcasts

2006-08-10

If your home was flooded, look for signs that your appliances have gotten wet. Throw away wet or flooded appliances to protect from shock and fire.  Created: 8/10/2006 by Emergency Communications System.   Date Released: 7/30/2008.

Association of tooth brushing behavior with oral hygiene index among students using fixed appliance

Science.gov (United States)

Ria, N.; Eyanoer, P.

2018-03-01

Uses of fixed appliance have become popular recently. The purpose of its use is to correct malposition of teeth in order to normalize the masticatory function and to eliminate the accumulation of food remain between the teeth. These will prevent the formation of caries and any periodontal tissue disease. Fixed appliance patients must routinely maintain their oral hygiene. This study was an analytical survey with cross-sectional design to know the relationship between behavior in tooth brushing of students using thefixed appliance and oral hygiene in Poltekkes Kemenkes Medan. The average of Oral Hygiene Index – Simplified (OHI-S) value of students using fixed appliance (2.68) was still above national target which is ≤2, and there was a relationship between behavior in tooth brushing of students using the fixed appliance and oral hygiene (phygiene and to prevent caries formation and periodontal disease patients using fixed appliances should maintain their dental health.

Design and explanation of organizational excellence model in home appliances industry

Directory of Open Access Journals (Sweden)

Seyed Abbas Kazemi

2012-01-01

Full Text Available Home appliances are considered as one of low margin and competitive industry in the world. This industry often needs significant amount of investment and resources and it often faces with some challenges during economic crises. In this paper, we present a framework for organizational excellence to detect any possible problems in home appliances industry. The proposed framework of this paper is used for a real-world case study of Iranian home appliances. The results of our survey indicate that there are four major dimensions involved with this industry including facilities, knowledge and skills, environment and vision. There are three criteria associated with facilities with 30 indexes, 14 criteria associated with knowledge and skills with 144 indexes, three criteria involved with environment with 33 indexes and five criteria linked with vision with 53 indexes. Therefore, home appliances in our case study needs 4 dimensions for achieving the organizational excellence.

Investigation of heat transfer and flow using ribs within gas turbine blade cooling passage: Experimental and hybrid LES/RANS modeling

Science.gov (United States)

Kumar, Sourabh

Gas turbines are extensively used for aircraft propulsion, land based power generation and various industrial applications. Developments in innovative gas turbine cooling technology enhance the efficiency and power output, with an increase in turbine rotor inlet temperatures. These advancements of turbine cooling have allowed engine design to exceed normal material temperature limits. For internal cooling design, techniques for heat extraction from the surfaces exposed to hot stream are based on the increase of heat transfer areas and on promotion of turbulence of the cooling flow. In this study, it is obtained by casting repeated continuous V and broken V shaped ribs on one side of the two pass square channel into the core of blade. Despite extensive research on ribs, only few papers have validated the numerical data with experimental results in two pass channel. In the present study, detailed experimental investigation is carried out for two pass square channels with 180° turn. Detailed heat transfer distribution occurring in the ribbed passage is reported for steady state experiment. Four different combinations of 60° and Broken 60° V ribs in channel are considered. Thermocouples are used to obtain the temperature on the channel surface and local heat transfer coefficients are obtained for various Reynolds numbers, within the turbulent flow regime. Area averaged data are calculated in order to compare the overall performance of the tested ribbed surface and to evaluate the degree of heat transfer enhancement induced by the ribs with. Flow within the channels is characterized by heat transfer enhancing ribs, bends, rotation and buoyancy effects. Computational Fluid Dynamics (CFD) simulations were carried out for the same geometries using different turbulence models such as k-o Shear stress transport (SST) and Reynolds stress model (RSM). These CFD simulations were based on advanced computing in order to improve the accuracy of three dimensional metal

Modeling of GE Appliances in GridLAB-D: Peak Demand Reduction

Energy Technology Data Exchange (ETDEWEB)

Fuller, Jason C.; Vyakaranam, Bharat GNVSR; Prakash Kumar, Nirupama; Leistritz, Sean M.; Parker, Graham B.

2012-04-29

The widespread adoption of demand response enabled appliances and thermostats can result in significant reduction to peak electrical demand and provide potential grid stabilization benefits. GE has developed a line of appliances that will have the capability of offering several levels of demand reduction actions based on information from the utility grid, often in the form of price. However due to a number of factors, including the number of demand response enabled appliances available at any given time, the reduction of diversity factor due to the synchronizing control signal, and the percentage of consumers who may override the utility signal, it can be difficult to predict the aggregate response of a large number of residences. The effects of these behaviors can be modeled and simulated in open-source software, GridLAB-D, including evaluation of appliance controls, improvement to current algorithms, and development of aggregate control methodologies. This report is the first in a series of three reports describing the potential of GE's demand response enabled appliances to provide benefits to the utility grid. The first report will describe the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The second and third reports will explore the potential of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation and the effects on volt-var control schemes.

49 CFR 176.54 - Repairs involving welding, burning, and power-actuated tools and appliances.

Science.gov (United States)

2010-10-01

...-actuated tools and appliances. 176.54 Section 176.54 Transportation Other Regulations Relating to..., burning, and power-actuated tools and appliances. (a) Except as provided in paragraph (b) of this section, repairs or work involving welding or burning, or the use of power-actuated tools or appliances which may...

Fixed-functional appliance treatment combined with growth hormone therapy.

Science.gov (United States)

Jung, Min-Ho

2017-09-01

The purpose of this study was to illustrate the effects of growth hormone (GH) therapy and fixed functional appliance treatment in a 13-year-old Class II malocclusion patient without GH deficiency. GH has been shown to effectively increase endochondral growth and induce a more prognathic skeletal pattern. Although a major concern in Class II retrognathic patients is chin deficiency, long-term studies have shown that the mandibular growth enhancement effects of functional appliances are clinically insignificant. This case report demonstrates that the mandible grew significantly during fixed functional appliance treatment combined with GH therapy, with stable results during 2 years 11 months of retention. More studies are needed to evaluate GH therapy as a supplement in Class II treatment. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Reducing Electricity Demand Peaks by Scheduling Home Appliances Usage

DEFF Research Database (Denmark)

Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

2011-01-01

Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users’ appliances...... should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power...... consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions...

A comparison of pain experienced by patients treated with labial and lingual orthodontic appliances.

Science.gov (United States)

Wu, Abby K Y; McGrath, Colman; Wong, Ricky W K; Wiechmann, D; Rabie, A Bakr M

2010-08-01

The aim of this prospective longitudinal study was to compare pain experiences among Chinese adult patients treated with labial and lingual orthodontic appliances. Sixty patients, 30 with labial appliances (18 females and 12 males, mean age 20.33 years, SD +/- 4.205) and 30 with lingual appliances (22 females and 8 males, mean age 21.63 years, SD +/- 2.236), rated their overall pain experience on a 100 mm visual analogue scale (VAS) at three time points: 1 week (T(1)), 1 month (T(2)), and 3 months (T(3)) after bracket placement. In addition, on a separate 100 mm VAS, they rated their pain experience at the locations of the tongue, lips, cheeks, gums, face, and jaw at T(1), T(2), and T(3). Changes in pain VAS were conducted using Friedman analysis of variance, area under the curve (AUC) analysis and the data were compared using a t-test. There was no significant difference in global ratings of pain among those treated with labial or lingual appliances (P > 0.05). Among both groups, global ratings of pain decreased over the study period (P appliances reported higher ratings of tongue pain (P appliances reported higher ratings of lip (P appliances rate similarly the level of overall pain they experience during treatment. Ratings of overall pain experienced decreased for both treatment groups with time. However, ratings of pain differed at various sites with respect to the type of orthodontic appliance. These findings have implications in informing patients' treatment decision-making processes regarding labial and lingual appliances and in the management of discomfort associated with different treatment modalities.

Eu-energy label for electric appliances; Das EU-Energielabel fuer Elektrogeraete

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-04-15

When buying a new appliances to have clear and understandable information on energy consumption to avoid later expensive surprices by to high power cost. But European classifiaction A to G of big household appliances is out of date and must be changed.(orig./GL)

Non-intrusive appliance load monitoring system based on a modern kWh-meter

Energy Technology Data Exchange (ETDEWEB)

Pihala, H. [VTT Energy, Espoo (Finland). Energy Systems

1998-12-01

Non-intrusive appliance load monitoring (NIALM) is a fairly new method to estimate load profiles of individual electric appliances in a small building, like a household, by monitoring the whole load at a single point with one recording device without sub-meters. Appliances have special electrical characteristics, the positive and negative active and reactive power changes during the time they are switched on or off. These changes are called events and are detected with a monitoring device called an event recorder. Different NIALM-concepts developed in Europe and in the United States are generally discussed. The NIALM-concept developed in this study is based on a 3-phase, power quality monitoring kWh-meter and unique load identification algorithms. This modern kWh-meter with a serial data bus to a laptop personal computer is used as die event recorder. The NIALM-concept of this presentation shows for the first time how a kWh-meter can be used at the same time for billing, power quality and appliance end-use monitoring. An essential part of the developed NIALM-system prototype is the software of load identification algorithms which runs in an off-line personal computer. These algorithms are able to identify, with a certain accuracy, both two-state and multi-state appliances. This prototype requires manual-setup in which the naming of appliances is performed. The results of the prototype NIALMS were verified in a large, single family detached house and they were compared to the results of other prototypes in France and the United States, although this comparison is difficult because of different supply systems, appliance stock and number of tested sites. Different applications of NIALM are discussed. Gathering of load research data, verification of DSM-programs, home automation, failure analysis of appliances and security surveillance of buildings are interesting areas of NIALM. Both utilities and customers can benefit from these applications. It is possible to

A modified palatal crib appliance for children with predetermined thumb-sucking habit - Case report

International Nuclear Information System (INIS)

AlEmran, Sulaiman

2008-01-01

The aim of this case report was to introduce a modified design of palatal crib habit breaking appliance that can be used for children with predetermined thumb-sucking habit. The appliance is made of two bands on the upper first permanent molars and an extended metal framework to cover the anterior of the palatal roof. The appliance was applied for 4 months on an 8-year-old boy who persistently continued the habit of thumb-sucking. The appliance proved to be very effective for arresting thumb-sucking habit. (author)

Comparison of emissions from selected commercial kitchen appliances and food products

Energy Technology Data Exchange (ETDEWEB)

Kuehn, T.H.; Gerstler, W.D.; Pui, D.Y.H.; Ramsey, J.W.

1999-07-01

Effluents have been measured from various grease-producing cooking processes in an attempt to quantify the emissions that enter typical commercial kitchen exhaust hoods. The appliances tested include gas and electric versions of single-sided griddles, open-vat deep fat fryers, under-fired broilers, full size convection ovens, and six burner ranges. Food products include hamburger, chicken breast, fries, sausage pizza, and a spaghetti meal. Emission data were obtained for particles, grease vapor, CO, CO{sub 2}, NO{sub x}, and hydrocarbons. Velocity and temperature fields were measured in the plume above each appliance. Results show that a large fraction of the grease emission is typically in vapor form. The broilers emit significantly more particles less than 2.5 {micro}m in size (PM 2.5) than the other appliances tested. Combustion by-products were measured for all gas appliances. Both the gas and electric broilers emitted significant amounts of CO when hamburgers were cooked. Aromatic hydrocarbon concentrations were below detectable limits in all tests.

Testing of a Stirling engine for heat + power cogeneration; Test eines Stirlingmotors zur Kraft-Waerme-Kopplung

Energy Technology Data Exchange (ETDEWEB)

Kramer, M.; Heinen, J. [RWE Energy AG, Essen (Germany)

2007-01-15

As part of a technology evaluation of distributed energy generators, RWE Energy AG extensively tested a micro combined heat and power appliance, powered by a Stirling engine developed by the British firm Microgen Energy Limited. Microgen Energy Limited is a specialist in micro combined heat and power (microCHP) based on unique Free-Piston Stirling generator technology Microgen is working with leading appliance manufacturers to integrate its core technology into a range of innovative microCHP products. The investigations concentrated on the determination of capacity, efficiency and emissions, the grid connection and behaviour at start-up and under varying loads. This article summarises the results of the tests and gives an overview of micro-CHP technologies (CHP=combined heat and power) and their possible significance to the market in the future. (orig.)

Comparative evaluation of sagittal anchorage loss in lingual and labial appliances during space closure: A pilot study

Directory of Open Access Journals (Sweden)

Shivanand Venkatesh

2015-01-01

Full Text Available Aim: The purpose of this investigation was to assess and compare the anchorage loss between labial and lingual appliance systems during space closure. Materials and Methods: Twenty subjects were part of the study among which 10 subjects (mean age 21 ± 3.6 years were treated using lingual appliance system (0.018" slot-STb™ and 10 subjects (mean age 19 ± 6.1 years were treated using labial preadjusted edgewise appliance system (0.018" slot-MBT™ . First premolar extractions were performed to enable retraction of anterior teeth. Lateral cephalometric radiographs were taken at two intervals, before starting space closure and after space closure that were connoted as T0 and T1 and were analyzed using the method described by Pancherz to measure anchorage loss. Intraclass correlation coefficient (ICC was used to evaluate intraexaminer reliability of the measurements. Student′s t-test was performed to verify any statistical significant correlation between the labial and lingual appliance systems. Statistical differences were determined at the 95% confidence level (P < 0.05. Results: The results showed that all ICC for lingual and labial group were ≥0.90 showing good repeatability of the measurements. Mean anchorage loss of 1.238 ± 0.17 mm in lingual appliance system and an anchorage loss of 2.06 ± 0.39 mm occurred with the labial appliance system. On the comparison between the two appliance systems, lingual appliance demonstrated a significantly lesser anchorage loss than did the labial appliance. Interpretation and Conclusion: This prospective study concludes with the fact that lingual appliance provided better anchorage control than labial appliance during space closure. Use of lingual appliance could be considered in critical anchorage cases when compared with labial appliance.

Assessment of Literature Related to Combustion Appliance Venting Systems

Energy Technology Data Exchange (ETDEWEB)

Rapp, V. H.; Less, B. D.; Singer, B. C.; Stratton, J. C.; Wray, C. P.

2015-02-01

In many residential building retrofit programs, air tightening to increase energy efficiency is often constrained by safety concerns with naturally vented combustion appliances. Tighter residential buildings more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spill combustion exhaust into the living space. Several measures, such as installation guidelines, vent sizing codes, and combustion safety diagnostics, are in place with the intent to prevent backdrafting and combustion spillage, but the diagnostics conflict and the risk mitigation objective is inconsistent. This literature review summarizes the metrics and diagnostics used to assess combustion safety, documents their technical basis, and investigates their risk mitigations. It compiles information from the following: codes for combustion appliance venting and installation; standards and guidelines for combustion safety diagnostics; research evaluating combustion safety diagnostics; research investigating wind effects on building depressurization and venting; and software for simulating vent system performance.

Using smart meter to monitor the energy consumption of home appliances

International Nuclear Information System (INIS)

Dong, M.; Xu, W.

2010-01-01

A smart meter provides the foundation for the smart grid, which represent the future electric system in terms of communications, sensors and automation to improve the flexibility, reliability and efficiency of power systems. Smart meters are installed at the utility-customer interface point to provide real-time power usage and price data to each electricity user. The purpose is to create customer awareness on electricity consumption and help users to conserve energy. Smart meters are being deployed throughout North America to replace most traditional meters. However, this paper discussed a major technical gap of the smart meter. Existing smart meters do not provide households with enough feedback needed to achieve effective energy saving. In order to support the energy conservation effort of a customer, the whole house energy data must be displayed on minute or second basis, and it must also be broken down into individual appliance levels. The data of an appliance's energy usage is the most useful information for users to modify their actions and conserve energy. This paper proposed to make the smart meter capable of reporting the overall consumption of a household, as well as monitoring how individual appliances use electricity. It presented a method on using different appliance signatures to identify appliances and make energy estimations on their respective consumptions. Paired with time-of-use or other real time pricing mechanisms, the method enables customers to save energy. This paper also demonstrated how to implement an algorithm on the smart meter platform. Future work will focus on making the algorithm more accurate and faster, and on integrating the smart meter with an appliance energy monitoring system. 21 refs., 6 tabs., 3 figs.

46 CFR 78.47-45 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to...-45 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with subchapter W...

Les rôles sexospécifiques et la violence dans les villes | CRDI ...

International Development Research Centre (IDRC) Digital Library (Canada)

20 oct. 2017 ... Une croissance rapide et des identités sexuelles ancrées favorisent la violence ... services des villes mettent les femmes et les minorités sexuelles en danger. .... Une étude de cas sur les femmes et les transports à Guwahati ...

DNA damage in oral mucosa cells of patients with fixed orthodontic appliances.

Directory of Open Access Journals (Sweden)

Farzin Heravi

2013-12-01

Full Text Available The release of toxic metal ions from orthodontic alloys has induced concerns regarding the biocompatibility of fixed appliances. This study investigated the genotoxic effect of metal appliances in a sample of patients undergoing fixed orthodontic treatment.The study included twenty-five healthy individuals requiring orthodontic therapy in both jaws. The patients were treated by stainless steel orthodontic brackets and nickel-titanium or stainless steel arch wires. The oral mucosa cells were gathered just before the appliance placement and 9 months later. The cells were centrifuged, fixed and dropped onto slides. After staining, the micronucleus (MN assay was used to determine genome alteration. The data were analyzed by paired sample t-test.The mean micronuclei frequency in the buccal mucosa was 10.6 ± 5.7 per 1000 cells before the appliance placement and 9.2 ± 6.37 per 1000 cells 9 months later. No significant difference was found in the MN count before and 9 months after therapy (p=0.336.Under the conditions used in this study, application of fixed orthodontic appliances did not expose healthy individuals to increased risk of DNA damage in oral mucosa cells.

46 CFR 196.37-37 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., etc. § 196.37-37 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

46 CFR 97.37-42 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., Etc. § 97.37-42 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

The effect of surface roughness on the heat exchange and pressure-drop coefficients; Influence des rugosites de paroi sur les coefficients d'echange thermique et de perte de charge

Energy Technology Data Exchange (ETDEWEB)

Malherbe, J M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1963-02-15

The effect of various types of roughness on the wall of an axial tube in an annular space of 15-25 mm cooled by an air-flow has been studied in the case of steady turbulence. Roughness of the type 'disrupter of the boundary layer' was set up using triangular threads of 0.2 to 0.4 mm thickness machined in the tube itself, or brass or glass wire wound on a smooth tube. Tests were also carried out using the roughness provided by regularly spaced pyramids 0.4 mm high. The results obtained showed that the heat exchange increased because of the presence of this roughness. A maximum in the heat exchange and pressure-drop coefficients was observed when the pitch equals about eight times the height of the thread. An analytical method has been developed and experiments have been carried out in which the two walls of the annular space were heated in such a way as to transmit unequal heat flows. The region considered is limited to Reynolds's numbers of between 5 X 10{sup 3} and 5 x 10{sup 4} and wall temperatures of under 250 deg C. (author) [French] L'effet de diverses rugosites sur la paroi du tube central d'un espace annulaire de diametre 15-25 mm refroidi par un ecoulement d'air a ete etudie en regime turbulent etabli. Des rugosites du type 'interrupteur de couche limite' etaient realisees au moyen de filets triangulaires, de 0,2 a 0,4 mm de hauteur usines dans l'epaisseur du tube ou de fils de laiton, ou de verre, enroules sur un tube lisse. Les essais ont porte egalement sur des rugosites constituees par des pyramides de 0,4 mm de hauteur et regulierement espacees. Les resultats obtenus ont mis en evidence une augmentation de transfert de chaleur due a la presence des elements rugueux. L'existence d'un maximum pour les coefficients d'echange thermique et de perte de charge a ete constate lorsque le pas atteint huit fois la hauteur des rugosites. Une methode analytique a ete etablie et des experiences ont ete realisees au cours desquelles les deux parois de l

Remote repair appliance

International Nuclear Information System (INIS)

Heumann, F.K.; Wilkinson, J.C.; Wooding, D.R.

1997-01-01

A remote appliance for supporting a tool for performing work at a work site on a substantially circular bore of a work piece and for providing video signals of the work site to a remote monitor comprises: a base plate having an inner face and an outer face; a plurality of rollers, wherein each roller is rotatably and adjustably attached to the inner face of the base plate and positioned to roll against the bore of the work piece when the base plate is positioned against the mouth of the bore such that the appliance may be rotated about the bore in a plane substantially parallel to the base plate; a tool holding means for supporting the tool, the tool holding means being adjustably attached to the outer face of the base plate such that the working end of the tool is positioned on the inner face side of the base plate; a camera for providing video signals of the work site to the remote monitor; and a camera holding means for supporting the camera on the inner face side of the base plate, the camera holding means being adjustably attached to the outer face of the base plate. In a preferred embodiment, roller guards are provided to protect the rollers from debris and a bore guard is provided to protect the bore from wear by the rollers and damage from debris. 5 figs

Energy Savings Potential and Research, Development, & Demonstration Opportunities for Commercial Building Appliances

Energy Technology Data Exchange (ETDEWEB)

Zogg, Robert [Navigant Consulting, Inc., Burlington, MA (United States); Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Ahlfeldt, Christopher [Navigant Consulting, Inc., Burlington, MA (United States); Hiraiwa, Hirokazu [Navigant Consulting, Inc., Burlington, MA (United States); Sathe, Amul [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States)

2009-12-01

This study characterizes and assesses the appliances used in commercial buildings. The primary objectives of this study were to document the energy consumed by commercial appliances and identify research, development and demonstration (RD&D) opportunities for efficiency improvements, excluding product categories such as HVAC, building lighting, refrigeration equipment, and distributed generation systems. The study included equipment descriptions, characteristics of the equipment’s market, national energy consumption, estimates of technical potential for energy-saving technologies, and recommendations for U.S. Department of Energy programs that can promote energy savings in commercial appliances.

Measured results and assessment of personal protection appliances against ionizing radiation

International Nuclear Information System (INIS)

Ge Lijuan; Lin Zhikai; Cao Jisheng; Zhu Pei; Tang Haiying; Liu Baiqun

2011-01-01

Objective: To monitor the protective qualities of personal protective appliances and to ensure the health and safety of radiological working personnel. Methods: The lead-equivalent thickness of personal protective appliances and materials was measured by means of standard lead slices. The lead equivalent thickness represents in terms of mm Pb. Results: 77 pieces of products and samples were measured altogether. The results indicate that the specific lead equivalents of lead-rubber plates were between 0.20-0.39 mm Pb/mm for 37 pieces of lead-rubber plates and the values of 6 pieces of samples were less than 0.25 mm Pb/mm, which did not accord with the requirement of the relational standard. 27 pieces of personal protection appliances were measured altogether. They were 12 pieces of protective clothes, 4 pieces of protective headgears, 5 pieces of protective neckpieces, 4 pieces of protective gloves and 2 pieces of protective masks. 13 pairs of lead-glass spectacles among them were measured altogether. The measured results for personal protective appliances and lead-glass spectacles showed that actually measured lead-equivalent were higher than the nominal lead-equivalent. Conclusions: The protective qualities are reliable for personal protection materials and appliances to be made in home and imported abroad. But the protective qualities of interventional protection gloves should be improved and made them better. (authors)

Controlled, Rapid Uprighting of Molars: A surprisingly Simple Solution The Pivot Arm Appliance.

Science.gov (United States)

Warise, Timothy R; Galella, Steve A

2015-01-01

In orthodontic cases where the regional anatomy provides limited room for eruption, there is etiologically a higher occurrence of tipped/impacted second molars. Although second molar extraction with third molar replacement is a useful option, the "Pivot Arm Appliance" encourages the uprighting of the second molar as a preferred treatment. The most unique and important attribute of the "Pivot Arm Appliance" is the rotating tube. In cases of access limitation, the disto-occlusal surface of the molar presents as one area that is accessible. Other features of the "Pivot Arm Appliance" include: The position of the rotator tube delivers optimal rotational force through the pivoting action of the tube/arm complex. The "Pivot Arm Appliance" takes advantage of the efficiency and simplicity of a Class I lever system. The anatomical fulcrum being the dense cortical bone located anterior to the ascending ramus. The vertical spring system is compact, reliable and delivers gentle controlled force in rotational direction. The lingual location of the "Pivot Arm Appliance" does not hinder the function of the tongue, impinge on the soft tissue or interfere with normal masticatory function. The ease of placement of the rotator tube and subsequent insertion of the spring. It is well to note the uprighting appliance provides a very useful and practical approach to the unique problem of severely tipped second molars with limited buccal access. The "Pivot Arm Appliance" does not function only in these situations but can be used in all cases of second molar uprighting of a moderate to severe nature.

Management of anterior dental crossbite with removable appliances

Directory of Open Access Journals (Sweden)

Ayca Tuba Ulusoy

2013-01-01

Full Text Available This case report describes the treatment of an 8-year-old girl with anterior dental crossbite using a series of removable appliances to bring the teeth into a normal position. Clinical presentation and intervention: A removable acrylic appliance with a bite plate incorporating a screw was used to correct the anterior dental crossbite and align the incisors. The subsequent eruption of the maxillary left lateral incisor on the palatinal side was treated with a second acrylic plate incorporating a labiolingual spring. After an 8-month period, the anterior crossbite involving multiple incisors was corrected.

A new geothermal source for spa and space heating in Lavey-les-Bains; Operation geothermique de Lavey-les Bains (VD). CESLA - Chaleur des Eaux Souterraines de Lavey S.A. Realisation du forage geothermique profond P600 et exploitation de la ressource energetique par pompage dans les puits P600 et P201 (juin 1997 - decembre 2002)

Energy Technology Data Exchange (ETDEWEB)

Bianchetti, G.

2002-07-01

This report presents the construction and the operating performance of a newly drilled borehole in Lavey-les-Bains in Switzerland, which is used to extract high-temperature geothermal water. Associated with an older geothermal source, this well delivering water at the temperature of 68 {sup o}C meets 95% of the heat demand of the Lavey medical and thermal centre, without any heat pump. The heat is used for space heating, ventilation and domestic hot water preparation as well as for the pools. The flow rate from this 517 meter deep well is typically 1,100 liters per minute. The report also describes in details the drilling process as well as the various measurements performed during this period of time. Plenty of figures and schematics are given concerning the technical characteristics of the well and its exploitation procedure. The author suggests the introduction of heat recovery, as water is rejected at a temperature of at least 30 {sup o}C.

Toward semantic interoperability of energy using and producing appliances in residential environments

NARCIS (Netherlands)

Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

2015-01-01

About two thirds of the energy consumed in buildings originates household appliances. Nowadays, appliances are often intelligent and networked devices that form complete energy consuming, producing, and managing systems. Reducing energy is therefore a matter of managing and optimizing the energy

Home Appliance Load Scheduling with SEMIAH

DEFF Research Database (Denmark)

Jacobsen, Rune Hylsberg; Ghasem Azar, Armin; Zhang, Qi

2015-01-01

The European research project SEMIAH aims at designing a scalable infrastructure for residential demand response. This paper presents the progress towards a centralized load scheduling algorithm for controlling home appliances taking power grid constraints and satisfaction of consumers into account....

Changes in the oral environment after placement of lingual and labial orthodontic appliances.

Science.gov (United States)

Lombardo, Luca; Ortan, Yildiz Öztürk; Gorgun, Özge; Panza, Chiara; Scuzzo, Giuseppe; Siciliani, Giuseppe

2013-09-11

This study compared the oral hygiene and caries risk of patients treated with labial and lingual orthodontic appliances throughout a prospective evaluation of the status of the oral environment before and after bracket placement. A total of 20 orthodontic patients aged 19 to 23 years were included in the study and were divided into two groups: 10 patients wore Roth labial appliance (American Orthodontics, Sheboygan, WI, USA) and 10 patients wore STb lingual appliance (Ormco Corporation, Glendora, CA, USA). Plaque index (PI), gingival bleeding index (GBI), salivary flow rate, saliva buffer capacity, salivary pH, and Streptococcus mutans and Lactobacillus counts in saliva were determined at three time points: before orthodontic appliance placement (T0), 4 weeks after bonding (T1), and 8 weeks after bonding (T2). After appliance placement, all patients were periodically educated to the oral hygiene procedures. Wilcoxon rank and Mann-Whitney U tests were used to determine intragroup and intergroup differences as regards qualitative data. To compare quantitative data between the groups, chi-square and Fisher's exact tests were undertaken, while intragroup differences were tested with McNemar test. The level of statistical significance was set at pappliance. The GBI value increased significantly between T0 and T1 but decreased significantly between T1 and T2 (pappliance. S. mutans counts increased significantly between T0 and T2 in the saliva samples of patients treated with lingual appliance. No statistically significant differences were found between S. mutans and Lactobacillus counts at the three terms of saliva collection in patients treated with labial appliance. No statistically significant differences were found between the two groups at the three time points as regards the salivary flow rate and saliva buffer capacity. Lingual and labial orthodontic appliances showed a different potential in modifying the investigated clinical parameters: patients wearing STb

Assessing consumer benefits of selected gas appliance technology center tasks. Topical report, April-December 1992

International Nuclear Information System (INIS)

Smith, T.R.; Bournakis, A.D.; Worek, W.M.; Kalensky, D.C.; Dombrowski, L.P.

1992-12-01

The Gas Appliance Technology Center (GATC) was created in 1983 to assist the gas industry in bringing about a new generation of reasonably priced, advanced gas appliances. The objective of the report is to evaluate consumer benefits of sixteen selected GATC tasks for the time period between 1983 and 1990. Tasks were selected for review based upon their degree of industry impact and how well they represented activities in the four targeted research areas of Space Conditioning, Commercial Appliances, Residential Appliances, and Codes and Standards

Realization of Intelligent Household Appliance Wireless Monitoring Network Based on LEACH Protocol

Directory of Open Access Journals (Sweden)

Weilong ZHOU

2014-06-01

Full Text Available The intelligent household appliance wireless monitoring network can real-time monitor the apparent power and power factor of various household appliances in different indoor regions, and can realize the real-time monitoring on the household appliance working status and performance. The household appliance wireless monitoring network based on LEACH protocol is designed in the paper. Firstly, the basic idea of LEACH routing algorithm is proposed. Aiming at the node-distribution feature of intelligent home, the selection of cluster head in the routing algorithm and the data transmission method at the stable communication phase is modified. Moreover, the hardware circuit of power acquisition and power factor measurement is designed. The realization of wireless monitoring network based on CC2530 is described, each module and the whole system were conducted the on-line debugging. Finally, the system is proved to meet the practical requirement through the networking test.

A new modified tandem appliance for management of developing Class III malocclusion

Directory of Open Access Journals (Sweden)

Ram Sukh

2013-01-01

Full Text Available Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior cross bite and retrognathic maxilla at the mixed dentition stage. Anterior cross bite was corrected in 3 months and the positive overjet of 4 mm after continued use of the appliance for 1 year. There was a significant improvement in profile of the patient. The use of this appliance in this type of malocclusion enabled the correction of malocclusion in a few months and encouraging favorable skeletal growth in the future.

A new modified tandem appliance for management of developing Class III malocclusion.

Science.gov (United States)

Sukh, Ram; Singh, Gyan P; Tandon, Pradeep

2013-10-01

Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior cross bite and retrognathic maxilla at the mixed dentition stage. Anterior cross bite was corrected in 3 months and the positive overjet of 4 mm after continued use of the appliance for 1 year. There was a significant improvement in profile of the patient. The use of this appliance in this type of malocclusion enabled the correction of malocclusion in a few months and encouraging favorable skeletal growth in the future.

Impacts of Imported Liquefied Natural Gas on Residential Appliance Components: Literature Review

Energy Technology Data Exchange (ETDEWEB)

Lekov, Alex; Sturges, Andy; Wong-Parodi, Gabrielle

2009-12-09

An increasing share of natural gas supplies distributed to residential appliances in the U.S. may come from liquefied natural gas (LNG) imports. The imported gas will be of a higher Wobbe number than domestic gas, and there is concern that it could produce more pollutant emissions at the point of use. This report will review recently undertaken studies, some of which have observed substantial effects on various appliances when operated on different mixtures of imported LNG. While we will summarize findings of major studies, we will not try to characterize broad effects of LNG, but describe how different components of the appliance itself will be affected by imported LNG. This paper considers how the operation of each major component of the gas appliances may be impacted by a switch to LNG, and how this local impact may affect overall safety, performance and pollutant emissions.

38 CFR 17.122 - Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices...

Science.gov (United States)

2010-07-01

... of the expenses of repairs to prosthetic appliances and similar devices furnished without prior... Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices furnished without prior authorization. The expenses of repairs to prosthetic appliances, or similar appliances...

The impact of orthodontic appliances on eating - young people's views and experiences.

Science.gov (United States)

Carter, Louise A; Geldenhuys, Mieke; Moynihan, Paula J; Slater, Dina R; Exley, Catherine E; Rolland, Sarah L

2015-06-01

Orthodontic appliances are known to cause patients difficulty with eating. Learning more about the issues patients face, while eating with orthodontic appliances in place, will allow us to create more informative and relevant patient information, thereby improving patient compliance and treatment success. This study aims to understand how orthodontic appliances impact on eating in the broader context and to explore adolescent patients' perceptions of eating with orthodontic appliances. Purposive sampling was used and 19 participants currently undergoing orthodontic treatment and aged 11-14 years were selected for either a focus group or semi-structured interview to explore eating-related issues. Data collection and analysis were carried out as an iterative process broadly following principles of thematic analysis. Data collection ceased when no new themes emerged. Two main themes relating to eating problems emerged: restriction of food choice and problems associated with the eating process. Participants reported restricting food choice due to physical aspects of the appliance, advice given by their orthodontist, fear of breakage and also to minimize embarrassment. Participants also reported problems with the time taken to eat, chewing problems, taste change and being messy while eating. Additionally, time in treatment, the location of eating and relationship with those present during eating influenced emotions. Some participants indicated a positive impact of orthodontic appliances on their diet. These results can be used to further inform dietary advice offered to patients. Factors were identified which may not be considered in clinical practice but which could improve the value of dietary advice given to patients.

Excision Les jeunes changent l'Afrique par les TIC

International Development Research Centre (IDRC) Digital Library (Canada)

Comité Inter-Africain sur les Pratiques Traditionnelles ayant effet sur la santé des ... Planche 7 - Perception genrée de la citoyenneté : les dire des femmes. 90 ...... dans le monde avec les migrations internationales, l'excision ne semble pas être ...... En utilisant les TIC pour exprimer leurs attentes et leurs besoins, les jeunes, ...

Full 3-dimensional digital workflow for multicomponent dental appliances: A proof of concept.

Science.gov (United States)

van der Meer, W Joerd; Vissink, Arjan; Ren, Yijin

2016-04-01

The authors used a 3-dimensional (3D) printer and a bending robot to produce a multicomponent dental appliance to assess whether 3D digital models of the dentition are applicable for a full digital workflow. The authors scanned a volunteer's dentition with an intraoral scanner (Lava Chairside Oral Scanner C.O.S., 3M). A digital impression was used to design 2 multicomponent orthodontic appliances. Biocompatible acrylic baseplates were produced with the aid of a 3D printer. The metal springs and clasps were produced by a bending robot. The fit of the 2 appliances was assessed by 2 experienced orthodontists. The authors assessed both orthodontic appliances with the volunteer's dentition and found the fit to be excellent. Clinicians can fully produce a multicomponent dental appliance consisting of both an acrylic baseplate and other parts, such as clasps, springs, or screws, using a digital workflow process without the need for a physical model of the patient's dentition. Plaster models can be superfluous for orthodontic treatment as digital models can be used in all phases of a full digital workflow in orthodontics. The arduous task of making a multicomponent dental appliance that involves bending wires can possibly be replaced by a computer, design software, a 3D printer, and a bending robot. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

Wisdom Appliance Control System

Science.gov (United States)

Hendrick; Jheng, Jyun-Teng; Tsai, Chen-Chai; Liou, Jia-Wei; Wang, Zhi-Hao; Jong, Gwo-Jia

2017-07-01

Intelligent appliances wisdom involves security, home care, convenient and energy saving, but the home automation system is still one of the core unit, and also using micro-processing electronics technology to centralized and control the home electrical products and systems, such as: lighting, television, fan, air conditioning, stereo, it composed of front-controller systems and back-controller panels, user using front-controller to control command, and then through the back-controller to powered the device.

Oral radiation protector appliance

International Nuclear Information System (INIS)

Persico, T.M.; Dudas, R.M.; Shusta, G.W.

1982-01-01

An appliance for protecting teeth, gingiva, periodontal or alveola bone, salivary glands, and adjacent body areas against the harmful side effects of radiation therapy consists of an intraoral portion and an extraoral portion that may be selectively attached. The intraoral portion is substantially u-shaped to encompass the teeth and adjacent areas. The intraoral part may be made of lead sheet coated with plastic; the extraoral portion may be of lead sheet

FIXED OR REMOVABLE APPLIANCE FOR EARLY ORTHODONTIC TREATMENT OF FUNCTIONAL ANTERIOR CROSSBITE.

Science.gov (United States)

Wiedel, Anna-Paulina

2015-01-01

Anterior crossbite with functional shift also called pseudo Class III is a malocclusion in which the incisal edges of one or more maxillary incisors occlude with the incisal edges of the mandibular incisors in centric relationship: the mandible and mandibular incisors are then guided anteriorly in central occlusion resulting in an anterior crossbite. Early correction, at the mixed dentition stage, is recommended, in order to avoid a compromising dentofacial condition which could result in the development of a true Class III malocclusion and temporomandibular symptoms. Various treatment options are available. The method of choice for orthodontic correction of this condition should not only be clinically effective, with long-term stability, but also cost-effective and have high patient acceptance, i.e. minimal perceived pain and discomfort. At the mixed dentition stage, the condition may be treated by fixed (FA) or removable appliance (RA). To date there is insufficient evidence to determine the preferred method. The overall aim of this thesis was therefore to compare and evaluate the use of FA and RA for correcting anterior crossbite with functional shift in the mixed dentition, with special reference to clinical effectiveness, stability, cost-effectiveness and patient perceptions. Evidence-based, randomized controlled trial (RCT) methodology was used, in order to generate a high level of evidence. The thesis is based on the following studies: The material comprised 64 patients, consecutively recruited from the Department of Orthodontics, Faculty of Odontology, Malmö University, Sweden and from one Public Dental Health Service Clinic in Malmö, Skane County Council, Sweden. The patients were no syndrome and no cleft patients. The following inclusion criteria were applied: early to late mixed dentition, anterior crossbite affecting one or more incisors with functional shift, moderate space deficiency in the maxilla, no inherent skeletal Class III discrepancy, ANB

A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization.

Science.gov (United States)

Ozkalayci, Nurhat; Yetmez, Mehmet

2016-01-01

The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

33 CFR 150.506 - When must the operator service inflatable lifesaving appliances and marine evacuation systems?

Science.gov (United States)

2010-07-01

... inflatable lifesaving appliances and marine evacuation systems? 150.506 Section 150.506 Navigation and...: OPERATIONS Emergency and Specialty Equipment Inflatable Lifesaving Appliances § 150.506 When must the operator service inflatable lifesaving appliances and marine evacuation systems? (a) The operator must...

Dynamic Appliances Scheduling in Collaborative MicroGrids System

Science.gov (United States)

Bilil, Hasnae; Aniba, Ghassane; Gharavi, Hamid

2017-01-01

In this paper a new approach which is based on a collaborative system of MicroGrids (MG’s), is proposed to enable household appliance scheduling. To achieve this, appliances are categorized into flexible and non-flexible Deferrable Loads (DL’s), according to their electrical components. We propose a dynamic scheduling algorithm where users can systematically manage the operation of their electric appliances. The main challenge is to develop a flattening function calculus (reshaping) for both flexible and non-flexible DL’s. In addition, implementation of the proposed algorithm would require dynamically analyzing two successive multi-objective optimization (MOO) problems. The first targets the activation schedule of non-flexible DL’s and the second deals with the power profiles of flexible DL’s. The MOO problems are resolved by using a fast and elitist multi-objective genetic algorithm (NSGA-II). Finally, in order to show the efficiency of the proposed approach, a case study of a collaborative system that consists of 40 MG’s registered in the load curve for the flattening program has been developed. The results verify that the load curve can indeed become very flat by applying the proposed scheduling approach. PMID:28824226

Adverse reactions to orthodontic appliances in nickel-allergic patients.

Science.gov (United States)

Volkman, Kristen K; Inda, Michael J; Reichl, Peter G; Zacharisen, Michael C

2007-01-01

Nickel allergy (NA) is common and causes more cases of allergic contact dermatitis (ACD) than all other metals combined. Many orthodontic appliances (ODAs) contain nickel but their clinical relevance in nickel-allergic patients is unclear. We aimed to characterize the relationship between NA and ODAs because the medical literature investigating this is controversial. A survey concerning adverse reactions to ODAs in patients with NA was distributed to members of the Wisconsin Society of Orthodontics. Forty-three surveys were analyzed. The surveyed group was experienced, representing a mean of 21.2 years in practice and averaging 242 appliances placed per year per orthodontist. Most new patients with orthodontia were 10-18 years old. Most wires used were nickel-titanium alloy. Although 76% of orthodontists inquired about NA at initial evaluation, 37% still placed nickel-containing ODAs in known nickel-allergic patients. Fifty percent placed a single intraoral appliance, observing for reactions. Three orthodontists applied ODAs to the skin similar to patch testing. Only 8 patients with reactions to ODAs were described in detail, 6 were female patients and 6 were aged 13-14 years. Intraoral and extraoral reactions were mild; diffuse urticaria was reported in one patient. Treatment included removing the appliances or changing to nonnickel alternatives with favorable outcomes. These cases, which included >33,000 patients, suggest a prevalence of 0.03%. Adverse reactions to ODAs in patients with NA have been observed but are uncommon. Using suitable alternatives, patients usually can be accommodated.

Réduire les risques et les pertes attribuables aux changements ...

International Development Research Centre (IDRC) Digital Library (Canada)

22 août 2014 ... Entre-temps, dans les pays plus riches, comme le Japon et les États‑Unis, les bâtiments et l'infrastructure font l'objet de nouvelles conceptions visant à prévenir les conséquences des tremblements de terre. Quelle comparaison feriez‑vous entre les plans d'adaptation aux tremblements de terre et les ...

Effects of heat and electricity saving measures in district-heated multistory residential buildings

International Nuclear Information System (INIS)

Truong, Nguyen Le; Dodoo, Ambrose; Gustavsson, Leif

2014-01-01

Highlights: • We analyzed the potential for energy savings in district heated buildings. • Measures that reduce more peak load production give higher primary energy savings. • Efficient appliances increase heat demand but give net primary energy savings. • Efficient appliances give the largest net primary energy savings. - Abstract: The effects of heat and electricity saving measures in district-heated buildings can be complex because these depend not only on how energy is used on the demand side but also on how energy is provided from the supply side. In this study, we analyze the effects of heat and electricity saving measures in multistory concrete-framed and wood-framed versions of an existing district-heated building and examine the impacts of the reduced energy demand on different district heat (DH) production configurations. The energy saving measures considered are for domestic hot water reduction, building thermal envelope improvement, ventilation heat recovery (VHR), and household electricity savings. Our analysis is based on a measured heat load profile of an existing DH production system in Växjö, Sweden. Based on the measured heat load profile, we model three minimum-cost DH production system using plausible environmental and socio-political scenarios. Then, we investigate the primary energy implications of the energy saving measures applied to the two versions of the existing building, taking into account the changed DH demand, changed cogenerated electricity, and changed electricity use due to heat and electricity saving measures. Our results show that the difference between the final and primary energy savings of the concrete-framed and wood-framed versions of the case-study building is minor. The primary energy efficiency of the energy saving measures depends on the type of measure and on the composition of the DH production system. Of the various energy saving measures explored, electricity savings give the highest primary energy savings

Analysis and simulation of heat transfer in human tooth during the curing of orthodontic appliance and food ingestion

Directory of Open Access Journals (Sweden)

J Velazquez-Lopez

2016-01-01

Full Text Available The aim of this study was to analyze and simulate the heat transfer in the human tooth undergoing fixed orthodontic appliances and food intake. An in vivo representative mathematic model of a layered thermographic profile was developed during the LED curing of Gemini bracket 0.022 in slot (conventional ligating system and Transbond XT adhesive. The characterization of the layered thermic response allowed to identify if during the LED curing process, according to manufacturer's specification (light curing unit, adhesive can induce pulpar necrosis. The profile's thermographic model was the simulation basis of many conditions such as food intake, due to in vivo metrology is affected by the impossibility of a correct apparatus position and the physiologic function of the oral cavity which is exposed to uncontrollable temperature changes. The metrology was carried out with a T-440 thermographic camera during LED curing bracket, using a LED curing light (Elipar S10 placed at 3 ± 1 mm for 5 s at each mesial and distal surface. The thermography outcomes were analyzed in the FLIR Tools Software, Microsoft Excel 2013 and SPSS 22. To adjust the mathematic model error, in vitro studies were performed on third molars for the purpose of realizing extreme exposition temperature condition tests caused by the LED curing unit without jeopardizing the human tooth vitality as would it be on in vivo experimentation. The bracket curing results according to manufacturer's conditions reached 39°C in vivo temperatures and 47°C on in vitro tests, which does not jeopardize human tooth vitality as said by previous researches, although, an LED curing precise protocol established by the manufacturer's LED curing light is sustained.

Recolonization of mutans steptococci on teeth with orthodontic appliances after antimicrobial therapy.

Science.gov (United States)

Attin, R; Thon, C; Schlagenhauf, U; Werner, C; Wiegand, A; Hannig, C; Attin, T

2005-10-01

The aim of the present study was to compare the recolonization pattern of mutans streptococci on densely colonized teeth with and without fixed orthodontic appliances after treatment with a 40 per cent chlorhexidine (CHX) varnish (EC 40, Explore). Healthy subjects free of carious lesions requiring fixed orthodontic appliance treatment but with high bacterial mutans streptococci saliva counts were recruited (n = 10). For baseline registration, plaque from buccal sites was sampled and cultivated on Dentocult strips. Following professional tooth cleaning, CHX varnish was applied to all teeth for 8 minutes. Subsequently, orthodontic brackets and bands were inserted in either the upper or lower arch. Eight weeks after varnish application the degree of recolonization with mutans streptococci was reassessed on the buccal sites. Statistical analysis showed that recolonization with mutans streptococci was significantly higher (P < 0.05) on teeth with orthodontic appliances. The results indicate that the use of fixed orthodontic appliances creates artificial environments suitable for the proliferation of mutans streptococci after CHX varnish suppression.

Heat pumps barometer - EurObserv'ER 2016

International Nuclear Information System (INIS)

2016-01-01

The heat pump (HP) sector had an excellent year in 2015. Appliance sales taking all heating and cooling market technologies into account, increased by 20% from 2212898 units in 2014 to 2655331 units in 2015. The emerging trend over the past few years specific to the HP segment for water-borne systems is that air-source HPs are clearly gaining market shares to the detriment of the ground-source HP market, while reversible HPs using air as their vector are taking advantage of record temperatures that have given a boost to the cooling market

Orthodontic parotitis: a rare complication from an orthodontic appliance.

Science.gov (United States)

McCarthy, Eileen; Cobb, Alistair R M

2012-12-01

A case is presented of a 14-year-old female undergoing orthodontic fixed appliance treatment who presented with right facial swelling in the parotid region. An initial diagnosis of acute infective parotitis was made by her primary care clinician. However, after clinical examination and ultrasonographic imaging, a diagnosis of salivary stasis secondary to inflammatory occlusion of Stensen's ductal orifice was made. The ductal orifice had been traumatized by the adjacent orthodontic appliance. This has not been described before in the literature. The differential diagnosis of parotid enlargement in children is discussed.

Les changements climatiques brouillent les prédictions des faiseurs ...

International Development Research Centre (IDRC) Digital Library (Canada)

8 oct. 2010 ... Depuis des générations, les autochtones de l'ouest du Kenya comptent sur les pouvoirs mystiques que possèdent les « faiseurs de pluie » du clan Nganyi pour prédire la météo. Cependant, le temps instable amené par les changements climatiques brouille les indices grâce auxquels les faiseurs de pluie ...

Valorisation de chaleur à bas niveau thermique Upgrading Low-Thermal-Level Heat

Directory of Open Access Journals (Sweden)

Cohen G.

2006-11-01

Full Text Available La mise en oeuvre à la fois de cycles thermodynamiques et de fluides adaptés permet d'élargir considérablement les possibilités de récupération et de valorisation de la chaleur à bas niveau contenue dans les rejets thermiques industriels, l'eau géothermale, le rayonnement solaire ou le milieu environnant. Ceci permettra une meilleure préservation des ressources énergétiques dans les principaux secteurs consommateurs d'énergie : résidentiel, tertiaire et industriel. On décrit les possibilités que présentent : - Les cycles thermodynamiques directs (pompes de chaleur à compression ou à absorption dans le domaine du chauffage résidentiel et tertiaire où elles sont déjà bien implantées et dont les applications commencent à pénétrer le secteur industriel. - Les cycles thermodynamiques inverses (thermotransformateurs et cycles moteurs à fluide organique pour lesquels les progrès techniques accomplis et l'accroissement du prix de l'énergie devraient permettre d'en assurer la diffusion progressive dans le secteur industriel. The implementation of both thermodynamic cycles and suitable fluids makes for a considerable widening of the capacity to recover and upgrade the low-level heat contained in industrial heat wastes, geothermal water, solar radiation or the surrounding environment. This will make for better conservation of energy resources in the leading sectors of energy consumption, i. e. residential, tertiary and industrial. This article describes these possibilities in the form of: (a Direct thermodynamic cycles (compression or absorption heat pumps in the field of home and tertiary heating where they have already obtained a solid foothold and for which applications are beginning te penetrate into the industrial sector. (b Reverse thermodynamic cycles (heat transformers and organic-fluid motor cycles for which the technical advances made and the increase in energy prices should enable them to spread progressively

How do household characteristics affect appliance usage? Application of conditional demand analysis to Japanese household data

International Nuclear Information System (INIS)

Matsumoto, Shigeru

2016-01-01

Although both appliance ownership and usage patterns determine residential electricity consumption, it is less known how households actually use their appliances. In this study, we conduct conditional demand analyses to break down total household electricity consumption into a set of demand functions for electricity usage, across 12 appliance categories. We then examine how the socioeconomic characteristics of the households explain their appliance usage. Analysis of micro-level data from the Nation Survey of Family and Expenditure in Japan reveals that the family and income structure of households affect appliance usage. Specifically, we find that the presence of teenagers increases both air conditioner and dishwasher use, labor income and nonlabor income affect microwave usage in different ways, air conditioner usage decreases as the wife's income increases, and microwave usage decreases as the husband's income increases. Furthermore, we find that households use more electricity with new personal computers than old ones; this implies that the replacement of old personal computers increases electricity consumption. - Highlights: •We conduct conditional demand analyses to study household appliance usage. •Micro-level data from the National Survey of Family and Expenditure in Japan are analyzed. •We show how household characteristics determine appliance usage. •High-income households use specific appliances less intensively than low-income households. •The replacement of old TVs and PCs lead to greater electricity consumption.

Reducing electricity demand peaks by scheduling home appliances usage

Energy Technology Data Exchange (ETDEWEB)

Rossello-Busquet, A.; Kardaras, G.; Baek Iversen, V.; Soler, J.; Dittmann, L.

2011-05-15

Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users' appliances should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions. On the contrary, the low priority devices have to pause their operation, when the algorithm dictates it, and resume it in the future. This can become beneficial for both energy companies and users. The electricity suppliers companies will be capable of regulating power generation during demand peaks periods. Moreover, users can be granted lower electricity bill rates for accepting delaying the operation of some of their appliances. In order to analyze this scenario, teletraffic engineering theory, which is used in evaluating the performance of telecommunication networks, is used. A reversible fair scheduling (RFS) algorithm, which was originally developed for telecommunication networks, is applied. The purpose is to analyze how a power consumption limit and priorities for home appliances will affect the demand peak and the users' everyday life. Verification of the effectiveness of the RFS algorithm is done by means of simulation and by using real data for power consumption and operation hours. The defined maximum power limit of 750 and 1000 Watt was not exceeded during

Retrofitting Combined Space and Water Heating Systems: Laboratory Tests

Energy Technology Data Exchange (ETDEWEB)

Schoenbauer, B.; Bohac, D.; Huelman, P.; Olson, R.; Hewitt, M.

2012-10-01

Better insulated and tighter homes can often use a single heating plant for both space and domestic water heating. These systems, called dual integrated appliances (DIA) or combination systems, can operate at high efficiency and eliminate combustion safety issues associated by using a condensing, sealed combustion heating plant. Funds were received to install 400 DIAs in Minnesota low-income homes. The NorthernSTAR DIA laboratory was created to identify proper system components, designs, operating parameters, and installation procedures to assure high efficiency of field installed systems. Tests verified that heating loads up to 57,000 Btu/hr can be achieved with acceptable return water temperatures and supply air temperatures.

Retrofitting Combined Space and Water Heating Systems. Laboratory Tests

Energy Technology Data Exchange (ETDEWEB)

Schoenbauer, B. [NorthernStar Building America Partnership, St. Paul, MN (United States); Bohac, D. [NorthernStar Building America Partnership, St. Paul, MN (United States); Huelman, P. [NorthernStar Building America Partnership, St. Paul, MN (United States); Olsen, R. [NorthernStar Building America Partnership, St. Paul, MN (United States); Hewett, M. [NorthernStar Building America Partnership, St. Paul, MN (United States)

2012-10-01

Better insulated and tighter homes can often use a single heating plant for both space and domestic water heating. These systems, called dual integrated appliances (DIA) or combination systems, can operate at high efficiency and eliminate combustion safety issues associated by using a condensing, sealed combustion heating plant. Funds were received to install 400 DIAs in Minnesota low-income homes. The NorthernSTAR DIA laboratory was created to identify proper system components, designs, operating parameters, and installation procedures to assure high efficiency of field installed systems. Tests verified that heating loads up to 57,000 Btu/hr can be achieved with acceptable return water temperatures and supply air temperatures.

Evolution of treatment mechanics and contemporary appliance design in orthodontics: A 40-year perspective.

Science.gov (United States)

McLaughlin, Richard P; Bennett, John C

2015-06-01

Until the early 1970s, successful treatment with the Begg technique and the Tweed edgewise technique required tedious wire bending. The introduction of Andrews' straight wire appliance changed that, and it was one of the most significant contributions in the history of orthodontics. The straight wire appliance significantly reduced the amount of wire bending and also brought along other options in treatment mechanics. Retraction of the canines with elastic chains and ligature wires became more common. Sliding mechanics in place of closing loops became the method of space closure for a significant number of clinicians. Edgewise force levels were initially used to close spaces; however, it was soon observed that lighter forces were more effective with sliding mechanics. Along with these changes, it became apparent that compensation in the appliance was needed, depending on the type of malocclusion and particularly with varying extraction sequences. Various appliance designs were developed to accommodate changes in mechanics and force levels. These modifications improved tooth positions at the end of treatment as long as the brackets were properly placed. These major changes in appliances, force levels, and treatment mechanics can be traced back to the work of Dr Lawrence Andrews and the straight wire appliances. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Lingual vs. labial fixed orthodontic appliances: systematic review and meta-analysis of treatment effects.

Science.gov (United States)

Papageorgiou, Spyridon N; Gölz, Lina; Jäger, Andreas; Eliades, Theodore; Bourauel, Christoph

2016-04-01

The aim of this systematic review was to compare the therapeutic and adverse effects of lingual and labial orthodontic fixed appliances from clinical trials on human patients in an evidence-based manner. Randomized and prospective non-randomized clinical trials comparing lingual and labial appliances were included. Risk of bias within and across studies was assessed using the Cochrane tool and the Grading of Recommendations Assessment, Development and Evaluation (GRADE) approach. Random-effects meta-analyses were conducted, followed by subgroup and sensitivity analyses. Six electronic databases were searched from inception to July 2015, without limitations. A total of 13 papers pertaining to 11 clinical trials were included with a total of 407 (34% male/66% female) patients. Compared with labial appliances, lingual appliances were associated with increased overall oral discomfort, increased speech impediment (measured using auditory analysis), worse speech performance assessed by laypersons, increased eating difficulty, and decreased intermolar width. On the other hand, lingual appliances were associated with increased intercanine width and significantly decreased anchorage loss of the maxillary first molar during space closure. Based on existing trials, there is insufficient evidence to make robust recommendations for lingual fixed orthodontic appliances regarding their therapeutic or adverse effects, as the quality of evidence was low. © 2016 Eur J Oral Sci.

A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization

Directory of Open Access Journals (Sweden)

Nurhat Ozkalayci

2016-01-01

Full Text Available The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

21 CFR 872.5410 - Orthodontic appliance and accessories.

Science.gov (United States)

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Therapeutic Devices § 872.5410 Orthodontic appliance and... device includes the preformed orthodontic band, orthodontic band material, orthodontic elastic band...

The stoma appliances market in five European countries: a comparative analysis.

Science.gov (United States)

Cornago, Dante; Garattini, Livio

2002-01-01

This comparative exercise analysed the domestic market for stoma appliances in five European countries--Denmark, France, Germany, Italy and the United Kingdom. National legislation, prescription procedures, delivery modalities and the market were investigated in each country. The analysis involved reviewing national and international literature on stoma appliances and interviewing a selected expert panel of market operators in each country comprising at least one health authority representative, one distributor of medical devices and one manufacturer. No specific relationship was found between the health care system framework and the stoma market, except for a greater inclination towards home care in national health services. All five countries reimburse stoma bags, but the distribution of these appliances varies widely, ranging from Denmark, where home delivery is mandatory, to Italy, where any channel can be used. The comparative analysis underlined two important features of the stoma bag market: the discretion of enterostomists in directing patients towards a specific brand of bags, and the patients' high brand loyalty. Despite that, the analysis did not identify any single country that could be considered a benchmark for stoma bag regulation. Each country deals with stoma appliances in different ways, making this a very fragmented market.

Former les jeunes chercheurs en vue d'influencer les politiques de ...

International Development Research Centre (IDRC) Digital Library (Canada)

2 mai 2016 ... Les conférences, les séances de tutorat et les stages financés par le CRDI en Asie, en Afrique et en Amérique latine renforcent les capacités des jeunes chercheurs en vue d'éclairer les politiques de télécommunications. Communications Policy Research South (CPRsouth) : les conférences présentent les ...

Orthodontic treatment with a series of removable appliances.

Science.gov (United States)

Chenin, David A; Trosien, Andrew H; Fong, Patricia F; Miller, Robert A; Lee, Rodney S

2003-09-01

In the United States, the demand for straight white teeth has never been more important to patients. Crowded, poorly aligned teeth are not esthetically pleasing and are difficult to keep clean. However, until recently, the process of straightening the teeth typically has involved appliances involving bands, brackets and wires that also can be difficult to clean. The desire for a cosmetic solution to misaligned teeth has led to an increase in the number of patients seeking veneers, crowns and other laboratory-fabricated cosmetic restorations. Some clinicians are not aware that there are other ways to align teeth without either significant enamel reduction or conspicuous fixed orthodontic appliances. An alternative method of treatment, involving a series of clear removable appliances, circumvents this shortcoming and enables tooth alignment while avoiding deterioration in the cosmetics of the smile during treatment. This article describes a method of treatment, Invisalign (Align Technology, Santa Clara, Calif.), that clinicians can use in conjunction with 3-D computer models to accomplish the esthetic and oral hygiene objectives during and after treatment. The authors present three case reports, all involving a chief concern of crowding. The first case involved treatment of both arches by interproximal reduction, alignment of teeth and leveling the curve of Spee. The second case involved treatment of both arches by proclination, expansion and minor interproximal reduction. The final case shows relief of lower-arch crowding via lower-incisor extraction. In addition to satisfying the patient's chief concern of desiring straight teeth, this method of treatment satisfies additional objectives of esthetic treatment and esthetic results with significant oral hygiene benefits. Clinicians can address a patient's chief concern effectively without requiring an inventory of appliances (such as bands, brackets, wires and instruments). Furthermore, the use of 3-D computer models

Evaluation of photo-activation appliances used in dentistry

Directory of Open Access Journals (Sweden)

Thales Ribeiro de Magalhães Filho

2008-01-01

Full Text Available Objective: Verify the Vickers microhardness promoted by three photo-activation appliances: one Halogen Light Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil and two Light Emitting Diodes. One with a larger diode (Ultraled, Dabi-Atlante, Ribeirão Preto, Brazil and the other with seven smaller diodes (Ultraled xp, Dabi-Atlante, Ribeirão Preto, Brazil in composites with different matrixes. Methods: Three test specimens were made for each resinous materials using silicone molds measuring 4 X 8 X 30 mm. Polymerization was performedin three stages and on the two surfaces. After having been submitted to careful polishing with sequential abrasive papers and diamond paste, the Vickers microhardness of the test specimens was determined. Afterwards these values were submitted to statistical analysis by the ANOVA table and Student’s-t test. Results: The microhardness values obtained in the hybrid composite were as follows: 51.63 kg/mm2 +- 3.27; 52.22 kg/mm2 +- 3.3; 38.08 kg/mm2 +-0.31 and in the ormocer, 41.87 kg/mm2 +- 2.36; 41.5 kg/mm2 +- 1.2; 33.63 kg/mm2 +- 1.2, by the Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil, Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil appliances, respectively. Conclusion: The Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil appliances promoted microhardness values that were similar between them and higher than the values produced by Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil in the composites. It was verified that the intensity of the photo-activator appliances is directly related to the microhardness they produce in the composites.

Induction Heating Process Design Using COMSOL Multiphysics Software

Directory of Open Access Journals (Sweden)

Andy Triwinarko

2011-08-01

Full Text Available Induction heating is clean environmental heating process due to a non-contact heating process. There is lots of the induction heating type that be used in the home appliance but it is still new technology in Indonesia. The main interesting area of the induction heating design is the efficiency of the usage of energy and choice of the plate material. COMSOL Multiphysics Software can be used to simulate and estimate the induction heating process. Therefore, the software can be used to design the induction heating process that will have a optimum efficiency. The properties of the induction heating design were also simulated and analyzed such as effect of inductors width, inductors distance, and conductive plate material. The result was shown that the good design of induction heating must have a short width and distance inductor and used silicon carbide as material plate with high frequency controller.

Influence of the heat flux and of the gas on heat transfer and friction coefficients in a smooth cylindrical tube; Influence du flux de chaleur et de la nature du gaz sur les coefficients d'echange et le frottement dans un tube cylindrique lisse

Energy Technology Data Exchange (ETDEWEB)

Delpont, J P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-12-15

The stainless steel tube used for the experiments is heated by means of d.c current; its inside diameter is 40 mm; its length is about 5.80 meters. Special core has been taken (heated rocket) to avoid heat loss and to provide very accurate measurements. The cooling gases tested are air and carbon dioxide at a pressure of 2.6 to 19 psi; the Reynolds number ranges from 70,000 to 10{sup 6}, the wall temperature and the heat flux reach respectively 430 deg C and 16 watts/cm{sup 2}. The Reynolds number Re{sub m}, Stanton number M{sub m} and friction coefficient f are computed by evaluating the physical properties of the gases at the mean temperature T{sub m}. For a given Reynolds number, a decrease of M{sub m} and of f is observed hen the heat flux increases, this decrease reaches 10 per cent in the experiments described. A formulation is proposed to express this effect in terms of a heat flow parameter (T{sub m} - T{sub m}) / T{sub p} used as a corrective factor (T{sub p} = wall temperature). The correlation formulae are: M{sub m} = 0.0168 Re{sub m}{sup -0.18} P{sub m}{sup -0.6} (1 - 0.4 [(T{sub p} - T{sub m}) / T{sub p}]) for air f = f{sub 0} (1 0.25 [(T{sub p} - T{sub m}) / T{sub p}]) for air M{sub m} = 0.0171 Re{sub m}{sup -0.18} P{sub m}{sup -0.6} (1 - 0.2 [(T{sub p} - T{sub m}) / T{sub p}]) for carbon dioxide f = f{sub 0} (1 - 0.20 [(T{sub p} - T{sub m}) / T{sub p}]) for carbon dioxide where f{sub 0} = the friction coefficient for isotherm flow. (author) [French] Le tube utilite a un diametre interieur de 40 mm; sa longueur est de 5,80 m environ; il est en acier inoxydable et chauffe par un courant continu. Des precautions particulieres (enceinte chauffante exterieure) ont ete prises pour eviter tout echange de chaleur avec le milieu exterieur et permettre des mesures extremement precises. Les gaz de refroidissement experimentes sont l'air et le gaz corbonique sous une pression de 1,8 a 13 hpz; les nombres de Reynolds vont de 70 000 a 10{sup 6}, la temperature de

The Determination of Load Profiles and Power Consumptions of Home Appliances

Directory of Open Access Journals (Sweden)

Fatih Issi

2018-03-01

Full Text Available In recent years, the increment of distributed electricity generation based on renewable energy sources and improvement of communication technologies have caused the development of next-generation power grids known as smart grids. The structures of smart grids have bidirectional communication capability and enable the connection of energy generated from distributed sources to any point on the grid. They also support consumers in energy efficiency by creating opportunities for management of power consumption. The information on power consumption and load profiles of home appliances is essential to perform load management in the dwelling accurately. In this study, the power consumption data for all the basic home appliances, utilized in a two-person family in Çankırı, Turkey, was obtained with high resolution in one-second intervals. The detailed power consumption analysis and load profile were executed for each home appliance. The obtained data is not only the average power consumption of each appliance but also characterizes different operating modes or their cycles. In addition, the impact of these devices on home energy management studies and their standby power consumptions were also discussed. The acquired data is an important source to determine the load profile of individual home appliances precisely in home energy management studies. Although the results of this study do not completely reflect the energy consumption behavior of the people who live in this region, they can reveal the trends in load demands based on a real sample and customer consumption behavior of a typical two-person family.

Using heat demand prediction to optimise Virtual Power Plant production capacity

NARCIS (Netherlands)

Bakker, Vincent; Molderink, Albert; Hurink, Johann L.; Smit, Gerardus Johannes Maria

2008-01-01

In the coming decade a strong trend towards distributed electricity generation (microgeneration) is expected. Micro-generators are small appliances that generate electricity (and heat) at the kilowatt level, which allows them to be installed in households. By combining a group of micro-generators, a

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes.

Science.gov (United States)

Kelly, Jack; Knottenbelt, William

2015-01-01

Many countries are rolling out smart electricity meters. These measure a home's total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the 'ground truth' demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

The effect of e-learning on the quality of orthodontic appliances

Directory of Open Access Journals (Sweden)

Schorn-Borgmann S

2015-08-01

Full Text Available Stephanie Schorn-Borgmann,1 Carsten Lippold,2 Dirk Wiechmann,3 Thomas Stamm2 1Private Practice, Nordkirchen, Germany; 2Department of Orthodontics, University of Münster, Münster, Germany; 3Department of Orthodontics, University of Hannover, Hannover, Germany Purpose: The effect of e-learning on practical skills in medicine has not yet been thoroughly investigated. Today’s multimedia learning environment and access to e-books provide students with more knowledge than ever before. The aim of this study is to evaluate the effect of online demonstrations concerning the quality of orthodontic appliances manufactured by undergraduate dental students. Materials and methods: The study design was a parallel-group randomized clinical trial. Fifty-four participants were randomly assigned to one of the three groups: 1 conventional lectures, 2 conventional lectures plus written online material, and 3 access to resources of groups one and two plus access to online video material. Three orthodontic appliances (Schwarz Plate, U-Bow Activator, and Fränkel Regulator were manufactured during the course and scored by two independent raters blinded to the participants. A 15-point scale index was used to evaluate the outcome quality of the appliances. Results: In general, no significant differences were found between the groups. Concerning the appliances, the Schwarz Plate obtained the highest scores, whereas the Fränkel Regulator had the lowest scores; however, these results were independent of the groups. Females showed better outcome scores than males in groups two and three, but the difference was insignificant. Age of the participants also had no significant effect. Conclusion: The offer that students could use additional time and course-independent e-learning resources did not increase the outcome quality of the orthodontic appliances. The advantages of e-learning observed in the theoretical fields of medicine were not achieved in the educational

Evaluation of dentoskeletal effects of Farmand functional appliance (Fa II) on class II malocclusion

OpenAIRE

Yassaei S.; Aghili H.; Razeghi D.

2007-01-01

Background and Aim: Functional appliances refer to a variety of removable or fixed appliances designed to alter the mandibular position both sagitally and vertically, resulting in orthodontic and orthopedic changes. Despite the long history of functional appliances, there is still much controversy related to their effectiveness and mode of action. The aim of this study was to evaluate dental and skeletal effects of Fa II in patients with class II malocclusion due to mandibular deficiency.Mate...

Influence of orthodontic appliance-derived artifacts on 3-T MRI movies.

Science.gov (United States)

Ozawa, Erika; Honda, Ei-Ichi; Parakonthun, Kulthida Nunthayanon; Ohmori, Hiroko; Shimazaki, Kazuo; Kurabayashi, Tohru; Ono, Takashi

2018-02-19

Magnetic resonance imaging (MRI) has been used to study configurations of speech organs in the resting state. However, MRI is sensitive to metals, and numerous types of metallic appliances, most of which have a large magnetic susceptibility, are used in orthodontic treatment and may cause severe artifacts on MRI. We have developed techniques for obtaining MRI movies of the oral region, to evaluate articulatory changes, especially movement of the tongue, palate, and teeth, pre- and post-orthodontic/orthognathic treatment. We evaluated the influence of artifacts caused by orthodontic appliances, including fixed retainers, metal brackets, and wires, on measurements in 3-T MRI movies. Sixteen healthy young adults (nine males, seven females; average age, 27 years) with normal occlusion were recruited. Four types of customized maxillary and mandibular plates were prepared by incorporating one of the following into the plate: (a) nothing, (b) a fixed canine-to-canine retainer, (c) metal brackets for the anterior and molar teeth, or (d) clear brackets for the anterior teeth and metal brackets for molars. A 3-T MRI movie, in segmented cine mode, was generated for each plate condition while participants pronounced a vowel-consonant-vowel syllable (/asa/). The size of the artifact due to the metallic brackets was measured. The face size and orthodontically important anatomical structures, such as the velum, the hard palate, and the laryngeal ventricle, were also measured. A large artifact was observed over the entire oral region around orthodontic appliances, altering regional visibility. The velopharyngeal height was measured as significantly longer in the presence of metal brackets. The maximum artifact size due to a metallic bracket was > 8 cm. Our results show that even if it is possible to obtain the measurements of palate length, nasion to sella, and nasion to basion in individuals wearing metal brackets for molars, the measurements might be affected due to the

Do different maxillary expansion appliances influence the outcomes of the treatment?

Science.gov (United States)

Algharbi, Muteb; Bazargani, Farhan; Dimberg, Lillemor

2018-01-23

There is no consensus in the literature regarding which rapid maxillary expansion (RME) design or activation rate benefits the patients the most. Therefore, the primary aim of this systematic review was to see whether there is a difference in the skeletal and dentoalveolar effects of different RME appliances in children and growing adolescents. The secondary aim was to see whether these effects are different when using different activation protocols for these appliances. The search was done in three databases (PubMed, Cochrane Library, and Web of Science). The following inclusion criteria were used: randomized controlled trial, prospective controlled studies, 15 or more patients in each study, human subjects up to 18 years of age, and RME effects had to be assessed by computed tomography/cone beam computed tomography. Quality of the methodology was classified according to the Grading of Recommendations Assessment, Development and Evaluation (GRADE) guidelines as high, moderate, or low. The search resulted in 145 titles and abstracts; 109 of them were excluded based on pre-established criteria. Thirty-six full-text articles were assessed for eligibility and 18 of which satisfied the inclusion criteria. Finally, seven articles were deemed eligible for full inclusion and revealed that all appliances and protocols showed significant expansion in the mid-palatal suture. No evidence was found for the cause of dental tipping. In this systematic review, having different age groups in each study and using different anatomical landmarks and outcome measures for assessing the skeletal and dental effects made it difficult to conduct a meta-analysis. There is moderate evidence that all designs produce significant expansion at the mid-palatal suture. However, lack of studies comparing appliances and protocols has been found. Finally, no evidence-based conclusions could be drawn about the appliance effect on teeth tipping. No appliance appears to be superior when it comes to

49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

Turning the appliance market around towards A++

Energy Technology Data Exchange (ETDEWEB)

Noergaard, Joergen S.; Guldbrandsen, Tom [Dept. of Civil Engineering, Technical Univ. of Denmark (Denmark); Brange, Birgitte; Karbo, Peter [Elsparefonden (Denmark)

2007-07-01

In an effort to exploit better the labelling schemes for appliances the Danish Electricity Saving Trust has run some campaigns on cold appliances. In 1999 focus was on getting people to choose A-rated models, the 2004 campaign focussed on A+, and in 2005 on A++. These campaigns and their results are described in the paper and some conclusions are drawn.The campaigns have consisted of various elements, namely 1) a general information about the campaigns, 2) a subsidy offered temporarily during some months to people buying the A, A+ and A++ models, 3) a website where people can easily find the most energy efficient model within their specification, and 4) in the website are also listed the shops, where consumers can get the appliances at lowest prices. The latter was the most innovative and maybe also the most effective measure in the package.Results showed up as a permanent U-turn of the market in the course of a few years. Where models C, D, E earlier dominated the market, the A, A+ and A++, came to dominate as the standard models in stock. Consequently, their prices dropped significantly. The theory of a rational market behavior is based on some assumptions, one being that full information is available to all actors. The website identifying to the consumers the shops with the lowest priced efficient models was a step in that direction, and the result did not fail to turn up.

Changes in subgingival microflora after placement and removal of fixed orthodontic appliances

Directory of Open Access Journals (Sweden)

Živković-Sandić Marija

2014-01-01

Full Text Available Introduction. The placement of fixed orthodontic appliances may lead to increased plaque accumulation and changes in subgingival microflora. Objective. The aim of this study was to examine the changes in frequency of subgingival microflora that occur after placement and removal of fixed orthodontic appliance using polymerase chain reaction (PCR. Methods. This study included 33 orthodontic patients, who were divided into two groups. Subgingival plaque samples were collected from the right upper incisor (U1 and right upper first molar (U6. In group A, the samples were taken three times: before placement appliance (T1, after one month (T2, and after 3 months (T3. In group B the samples were also taken three times: before appliance removal (T1, after one month (T2, and after three months (T3. PCR method was used to determine the presence of P. gingivalis, A. actinomycetemcomitans, T. forsythia, and P. intermedia. Results. In group A the frequency of P. gingivalis showed statistically significant decrease at U1 (p=0.049 and U6 (p=0.008, from T1 to T2, and at U1 (p=0.048 from T1 to T3. In group B only the frequency of T. forsythia showed a statistically significant decrease, at U6 (T1 vs. T2, p=0.004; T1 vs. T3, p=0.0003. Regarding other analyzed bacteria, changes in the presence were noticed but no statistical significance was found. Conclusion. Placement of fixed appliances may have an impact on subgingival microflora, but in the first months after the placement and removal of the appliance changes were not significant, probably due to good oral hygiene. [Projekat Ministarstva nauke Republike Srbije, br. 175075

Space Maintenance with an Innovative "Tube and Loop" Space Maintainer (Nikhil Appliance).

Science.gov (United States)

Srivastava, Nikhil; Grover, Jyotika; Panthri, Prerna

2016-01-01

Despite the best efforts in prevention, premature loss of primary teeth continues to be a common problem in pediatric dentistry, resulting in disruption of arch integrity and adversely affecting the proper alignment of permanent successors. Space maintainers (SMs) are special appliances used for maintaining space created due to premature loss of primary teeth. Band and loop SM is mostly indicated for the premature loss of single primary molar, but this appliance has a number of limitations both for operators and for patients. Presented in this article is an innovative "Tube and Loop" SM (Nikhil appliance) which offers several advantages over the conventional band and loop SM. It is not only easy and quick to fabricate but can also be completed in a single sitting and cumbersome steps like impression making and laboratory procedures namely soldering are eliminated. How to cite this article: Srivastava N, Grover J, Panthri P. Space Maintenance with an Innovative "Tube and Loop" Space Maintainer (Nikhil Appliance). Int J Clin Pediatr Dent 2016;9(1):86-89.

Mapping chemical elements on the surface of orthodontic appliance by SEM-EDX.

Science.gov (United States)

Mikulewicz, Marcin; Wołowiec, Paulina; Michalak, Izabela; Chojnacka, Katarzyna; Czopor, Wojciech; Berniczei-Royko, Adam; Vegh, Andras; Gedrange, Thomas

2014-05-25

During orthodontic treatment, the various elements that constitute the fixed appliance undergo different processes. As a result of a change of the surface, elution/coverage of metals on the surface can be observed in the process of corrosion/passivation. Scanning electron microscopy with an energy-dispersive X-ray analytical system (SEM-EDX) was used to analyze the composition of stainless steel elements of orthodontic fixed appliances (before and after orthodontic treatment), to obtain the composition of the surface of the elements. The analyzed elements were: brackets (Victory Series APC PLUS 022, 3M Unitek, Monrovia, CA, USA); wires (0.017×0.025, 3M Unitek, Monrovia, CA, USA); and bands (37+, 3M Unitek, Monrovia, CA, USA). The results showed a decrease of chromium and iron contribution to the surface, with increase of oxygen content in used vs. new elements of the appliance. Our results confirm the formation of oxides (passivation layer) on the surface of stainless steel as a result of the presence of the orthodontic appliance in patients' oral cavities.

Created in Close Interaction with the Industry: The Smart Appliances REFerence (SAREF) Ontology

NARCIS (Netherlands)

Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

2015-01-01

Around two thirds of the energy consumed by buildings can be traced back to the residential sectors and thus household appliances. Today, most appliances are highly intelligent and networked devices, in principle being able to form complete energy consuming, producing, and managing systems. Reducing

A randomized clinical trial comparing mandibular incisor proclination produced by fixed labial appliances and clear aligners.

Science.gov (United States)

Hennessy, Joe; Garvey, Thérèse; Al-Awadhi, Ebrahim A

2016-09-01

To compare the mandibular incisor proclination produced by fixed labial appliances and third generation clear aligners. Patients underwent a course of orthodontic treatment using either fixed labial appliances or clear aligners (Invisalign). Mandibular incisor proclination was measured by comparing pretreatment and near-end treatment lateral cephalograms. Eligibility criteria included adult patients with mild mandibular incisor crowding (clear aligner group. Baseline characteristics were similar for both groups: Fixed appliance mean crowding was 2.1 ± 1.3 mm vs clear aligner mean crowding, 2.5 ± 1.3 mm; pretreatment mean mandibular incisor inclination for the fixed appliance group was 90.8 ± 5.4° vs 91.6 ± 6.4° for the clear aligner group. Fixed appliances produced 5.3 ± 4.3° of mandibular incisor proclination. Clear aligners proclined the mandibular incisors by 3.4 ± 3.2°. The difference between the two groups was not statistically significant (P > .05). There was no difference in the amount of mandibular incisor proclination produced by clear aligners and fixed labial appliances in mild crowding cases.

Open-bite treatment utilizing clear removable appliances with intermaxillary and intramaxillary elastics.

Science.gov (United States)

Park, Jae Hyun; Kim, Tae Weon

2009-01-01

Clear removable appliances with elastics can be effective and efficient in extruding maxillary teeth during aligner treatment or following a relapse of an open bite. Some patients with open bites refuse to wear conventional fixed appliances. In these individuals, clear aligners with elastics could be a valuable alternative. © 2009 Quintessence Publishing Co, Inc. All Rights Reserved

33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

Science.gov (United States)

2010-07-01

... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and...: OPERATIONS Emergency and Specialty Equipment Launching Appliances § 150.504 When must the operator service and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching...

A test procedure for energetic and performance analysis of cold appliances for the food industry

International Nuclear Information System (INIS)

Armani, F; Boscolo, A

2013-01-01

In this article we present a novel approach for the characterization of cold appliances and in particular of refrigerators based on the standard vapour compression cycle with a reciprocating on/off compressor. The test procedure is based on a virtual instrument that perform both the stimulus and the data acquisition on the device under test. Acquired data is elaborated to fit a semi-empirical model based on the energetic balances between thermal and electrical sub systems and the heat exchanged with the environment. This approach results in a simple method to calculate useful parameters of the refrigerator, such as energetic performance, cooling effect and limit values of thermal loads. The test procedure requires only a few temperatures and the electric power consumption to be monitored, resulting in a low impact on the refrigerator. Preliminary tests showed a good estimation of parameters and prediction of energy consumption and heat extraction capacity of the refrigerator under test

What can we learn from high-frequency appliance-level energy metering? Results from a field experiment

International Nuclear Information System (INIS)

Chen, Victor L.; Delmas, Magali A.; Kaiser, William J.; Locke, Stephen L.

2015-01-01

This study uses high-frequency appliance-level electricity consumption data for 124 apartments over 24 months to provide a better understanding of appliance-level electricity consumption behavior. We conduct our analysis in a standardized set of apartments with similar appliances, which allows us to identify behavioral differences in electricity use. The Results show that households' estimations of appliance-level consumption are inaccurate and that they overestimate lighting use by 75% and underestimate plug-load use by 29%. We find that similar households using the same major appliances exhibit substantial variation in appliance-level electricity consumption. For example, households in the 75th percentile of HVAC usage use over four times as much electricity as a user in the 25th percentile. Additionally, we show that behavior accounts for 25–58% of this variation. Lastly, we find that replacing the existing refrigerator with a more energy-efficient model leads to overall energy savings of approximately 11%. This is equivalent to results from behavioral interventions targeting all appliances but might not be as cost effective. Our findings have important implications for behavior-based energy conservation policies. - Highlights: • Hourly electricity usage was collected from 124 comparable apartments for 24 months. • Households overestimate lighting use by 75% and underestimate HVAC usage by 29%. • Households using the same appliances show substantial variations in electricity use. • Plug load accounts for the largest share of electricity use at all hours of the day. • Savings of 11% were achieved by replacing old refrigerators

The effect of e-learning on the quality of orthodontic appliances.

Science.gov (United States)

Schorn-Borgmann, Stephanie; Lippold, Carsten; Wiechmann, Dirk; Stamm, Thomas

2015-01-01

The effect of e-learning on practical skills in medicine has not yet been thoroughly investigated. Today's multimedia learning environment and access to e-books provide students with more knowledge than ever before. The aim of this study is to evaluate the effect of online demonstrations concerning the quality of orthodontic appliances manufactured by undergraduate dental students. The study design was a parallel-group randomized clinical trial. Fifty-four participants were randomly assigned to one of the three groups: 1) conventional lectures, 2) conventional lectures plus written online material, and 3) access to resources of groups one and two plus access to online video material. Three orthodontic appliances (Schwarz Plate, U-Bow Activator, and Fränkel Regulator) were manufactured during the course and scored by two independent raters blinded to the participants. A 15-point scale index was used to evaluate the outcome quality of the appliances. In general, no significant differences were found between the groups. Concerning the appliances, the Schwarz Plate obtained the highest scores, whereas the Fränkel Regulator had the lowest scores; however, these results were independent of the groups. Females showed better outcome scores than males in groups two and three, but the difference was insignificant. Age of the participants also had no significant effect. The offer that students could use additional time and course-independent e-learning resources did not increase the outcome quality of the orthodontic appliances. The advantages of e-learning observed in the theoretical fields of medicine were not achieved in the educational procedures for manual skills. Factors other than e-learning may have a higher impact on manual skills, and this should be investigated in further studies.

The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes

Science.gov (United States)

Kelly, Jack; Knottenbelt, William

2015-03-01

Many countries are rolling out smart electricity meters. These measure a home’s total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the ‘ground truth’ demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

Heat-pump tumble dryers; Waermepumpen-Tumbler

Energy Technology Data Exchange (ETDEWEB)

Bluemig, N.; Gatter, R.

2004-07-01

Commonly available tumble dryers with air-vented or condenser systems in combination with electrical heating have a high specific energy consumption and never fulfil the requirements for Energy Label Class A (<= 0.55 kWh/kg.). The development of a tumbler with a heat pump system has enabled a reduction of almost 50% in the specific energy consumption. In addition to ecological aspects, this means that a significant reduction in energy costs is achieved as well as a beneficial effect on room climate. Other considerations taken into account in the development of the 6.5 kg tumbler were: (i) Compact modular design; integration of the heat pump in the appliance casing; (ii) Long operating life without clogging-up of the heat exchanger by fluff; (iii) Stable process throughout the drying in ambient temperatures of up to 35 {sup o}C. Process stability in particular presented a tough challenge. The solution came in the form of an additional booster condenser that prevents overheating of the compressor towards the end of the process when only negligible amounts of energy are being carried away as a result of the low residual moisture in the laundry. It proved possible to reduce the specific power consumption to less than 0.4 kWh/kg and the leak rate to less 30 %. Thanks to the compact, modular design, the heat pump could be integrated in a housing which has the same size as a conventional 6.5 kg dryer. Clogging-up of the heat exchanger surfaces with fluff was prevented by a multi-stage cascade filtration system. With this heat pump dryer it has been possible for the very first time to develop to series production and launch an appliance in the up to 6.5 kg category that not only fulfils the requirements of Energy Label Class A but also offers a serious alternative to conventional tumble dryers thanks to its compact design, operating safety and ease of operation. Future development opportunities lie in more cost-effective production of the heat pump module, shortening of

Estimating returns to scale and scale efficiency for energy consuming appliances

Energy Technology Data Exchange (ETDEWEB)

Blum, Helcio [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Efficiency Standards Group; Okwelum, Edson O. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Efficiency Standards Group

2018-01-18

Energy consuming appliances accounted for over 40% of the energy use and $17 billion in sales in the U.S. in 2014. Whether such amounts of money and energy were optimally combined to produce household energy services is not straightforwardly determined. The efficient allocation of capital and energy to provide an energy service has been previously approached, and solved with Data Envelopment Analysis (DEA) under constant returns to scale. That approach, however, lacks the scale dimension of the problem and may restrict the economic efficient models of an appliance available in the market when constant returns to scale does not hold. We expand on that approach to estimate returns to scale for energy using appliances. We further calculate DEA scale efficiency scores for the technically efficient models that comprise the economic efficient frontier of the energy service delivered, under different assumptions of returns to scale. We then apply this approach to evaluate dishwashers available in the market in the U.S. Our results show that (a) for the case of dishwashers scale matters, and (b) the dishwashing energy service is delivered under non-decreasing returns to scale. The results further demonstrate that this method contributes to increase consumers’ choice of appliances.

Energy and associated greenhouse gas emissions from household appliances in Malaysia

International Nuclear Information System (INIS)

Saidur, R.; Masjuki, H.H.; Jamaluddin, M.Y.; Ahmed, S.

2007-01-01

Today, electricity is an indispensable key for civilization and development. The trend of electricity consumption is rather escalating. Electricity generation principally depends upon fossil fuels. In one hand, the stocks of these fuels have been confirmed to be critically limited. On the other hand, in process of electricity generation by means of these fuels, a number of poisonous by-products adversely affect the conservation of natural eco-system. Further, electricity driven appliances use emanate anti-environmental gases that also affect human health and climate. Therefore, estimation of energy consumption for operating household appliances, savings of energy under policy intervention, and emission of poisonous gases in a fast developing country deserve academic attention. This paper focuses on estimation of energy consumption, energy savings, reduction of emissions of greenhouse gases for use of household appliances in Malaysia between 1999 and 2015. In the upstream side of electricity generation, the study estimates the amount of greenhouse gases (GHGs) resulting from burning of fossil fuels. In downstream side, it considers the energy savings and reduction of CHGs. The results show that significant amount of energy can be saved and thus huge volume of toxic emissions can be controlled. The findings can be useful to policy makers as well as household appliances users

Research and Development of Natural Draft Ultra-Low Emissions Burners for Gas Appliances

Energy Technology Data Exchange (ETDEWEB)

Therkelsen, Peter [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cheng, Robert [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sholes, Darren [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2017-08-31

Combustion systems used in residential and commercial cooking appliances must be robust and easy to use while meeting air quality standards. Current air quality standards for cooking appliances are far greater than other stationary combustion equipment. By developing an advanced low emission combustion system for cooking appliances, the air quality impacts from these devices can be reduced. This project adapted the Lawrence Berkeley National Laboratory (LBNL) Ring-Stabilizer Burner combustion technology for residential and commercial natural gas fired cooking appliances (such as ovens, ranges, and cooktops). LBNL originally developed the Ring-Stabilizer Burner for a NASA funded microgravity experiment. This natural draft combustion technology reduces NOx emissions significantly below current SCAQMD emissions standards without post combustion treatment. Additionally, the Ring-Stabilizer Burner technology does not require the assistance of a blower to achieve an ultra-low emission lean premix flame. The research team evaluated the Ring-Stabilizer Burner and fabricated the most promising designs based on their emissions and turndown.

Application of smart technology in monitoring and control of home appliances

Directory of Open Access Journals (Sweden)

A. A. Abdulrazaq

2017-08-01

Full Text Available The inherent dependency of home appliances on human for monitoring and control has been found to be mainly responsible for power wastage, and increase in the rate of wear and tear, which invariably implies additional spending on the part of owners. The smart technology provides a way out. This paper presents an automated system which is based on arduino and android device for monitoring and controlling appliances to prevent the wastage of power. The system design is based on the Microcontroller MIKRO-C software, active sensors and wireless internet services which is used in different monitoring and control processes of fan, air-conditioner, light and heater. The system when tested performs efficiently in monitoring and controlling through switching the appliances in the room based on human presence and environmental changes due to light intensity and temperature variation.

Waste heat utilization in the thermal spa of Lavey-les-Bains; Etude de la valorisation des rejets thermiques des Bains de Lavey

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This final report for the Swiss Federal Office of Energy looks at the possibilities for improved waste water utilization in the Lavey-les-Bains thermal spa, Switzerland. According to the regulations in force, the temperature of the waste water rejected into the Rhone river shall not exceed 30 {sup o}C, what is currently not the case. Also the operational cost shall be reduced and the waste water quality improved. The installations are presented. From the two geothermal wells, mineral water comes out at an average flow rate of 940 l/min and a temperature of 63 {sup o}C. Actual waste water data are reported. The measured thermal water consumption data, including seasonal variations, are analysed by computerized simulation and measures to reduce the consumed volume by the optimization of internal procedures are evaluated. Measures to reduce the quantity of the rejected free chlorine are discussed. Several possible adaptations of the existing space heating, domestic water heating and pools' heating are evaluated, including cost. In addition, extensions of the thermal spa center to recreational activities are discussed, as the construction of a tropical greenhouse is.

Mesurer et comparer les contextes et les politiques alimentaires en ...

International Development Research Centre (IDRC) Digital Library (Canada)

En Amérique latine, les maladies non transmissibles (MNT) sont responsables de trois décès sur quatre. Une mauvaise alimentation fait augmenter de plus en plus les décès et les maladies évitables et prématurées liés aux MNT. Dans le but de régler ce problème, ce projet suivra et comparera les contextes et les ...

Efficacy of the Nance appliance as an anchorage-reinforcement method.

Science.gov (United States)

Al-Awadhi, Ebrahim A; Garvey, Therese M; Alhag, Mohamed; Claffey, Noel M; O'Connell, Brian

2015-03-01

The Nance appliance is widely considered to be an efficient method of anchorage reinforcement; however, much of the perceived advantage is based on clinical judgment. The aim of this study was to assess the amounts of anchorage loss and desired tooth movement associated with the Nance appliance. The mandibular arches of 7 beagle dogs were used. The first and third premolars were extracted. Reference miniscrews were placed at the first premolar sites as stable references to measure the amounts of anchorage loss and desired tooth movement. Four beagles were fitted with custom-made Nance appliances on the fourth premolars and orthodontic bands on the second premolars (Nance group). Three beagles were fitted with orthodontic bands on the second and fourth premolars with no anchorage reinforcement (control group). The second premolars were retracted over 15 weeks in both groups. The amounts of second premolar movement (desired tooth movement) and fourth premolar movement (anchorage loss) were recorded at 5, 10, and 15 weeks. The percentages of desired tooth movement and anchorage loss to the total space closure were calculated. The mean desired tooth movement was significantly more in the Nance group than in the control group at 10 weeks (P appliance did not provide absolute anchorage, but there was significantly less anchorage loss with it than in the control group. The majority of anchorage loss occurred during the first 10 weeks in the Nance group. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Customer service in appliance sales departments of selected ...

African Journals Online (AJOL)

Customer service in appliance sales departments of selected prominent retail outlets: store manager, ... A single measurement of customers' perception of service quality in various stores however suggested ... AJOL African Journals Online.

Corrosion of weldments in orthodontic appliances

International Nuclear Information System (INIS)

Vazquez, S.M.; Riesgo, O.; Duffo, G.S.

1997-01-01

The study of corrosion-related problems of dental materials has undergone a considerable development in recent years in order to avoid the use of materials with insufficient corrosion resistance in patients mouth. The subject of the present work was to study a particular type of corrosion: galvanic corrosion. One of the most common case of galvanic couples in patients mouth are the orthodontic appliances. The materials studied in the present work were stainless steel strips and silver-copper wires, isolated and welded between them. The electrochemical tests were performed in a NaCl 0.1M and Lactic Acid 0.1 M solution (pH2.3), and after test, the specimens were observed using the optical and scanning electron microscope. The results show that when stainless steel is coupled with a silver solder, the last is the anode of the galvanic couple. As a consequence of this, the silver solder undergone a severe attack. Stainless steel orthodontic appliances with silver solder are feasibly destroyed due to a severe attack on the filler metal disjoining the welded parts. (author) 9 refs

Three case reports demonstrating treatment of relatively complex orthodontic cases using a completely customised lingual appliance.

Science.gov (United States)

Buckley, John

2016-01-01

It is a commonly held misconception among Irish dentists that only minor malocclusions can be treated with lingual appliances. This article demonstrates the use of contemporary completely customised lingual orthodontic appliances to treat a diverse range of malocclusions, to a satisfactory level, and thereby may disabuse clinicians of the belief that only minor malocclusions can be treated with lingual appliances.

Class II malocclusion with complex problems treated with a novel combination of lingual orthodontic appliances and lingual arches.

Science.gov (United States)

Yanagita, Takeshi; Nakamura, Masahiro; Kawanabe, Noriaki; Yamashiro, Takashi

2014-07-01

This case report describes a novel method of combining lingual appliances and lingual arches to control horizontal problems. The patient, who was 25 years of age at her first visit to our hospital with a chief complaint of crooked anterior teeth, was diagnosed with skeletal Class II and Angle Class II malocclusion with anterior deep bite, lateral open bite, premolar crossbite, and severe crowding in both arches. She was treated with premolar extractions and temporary anchorage devices. Conventionally, it is ideal to use labial brackets simultaneously with appliances, such as a lingual arch, a quad-helix, or a rapid expansion appliance, in patients with complex problems requiring horizontal, anteroposterior, and vertical control; however, this patient strongly requested orthodontic treatment with lingual appliances. A limitation of lingual appliances is that they cannot be used with other conventional appliances. In this report, we present the successful orthodontic treatment of a complex problem using modified lingual appliances that enabled combined use of a conventional lingual arch. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

A randomized clinical trial of a new orthodontic appliance to improve upper airway obstruction in infants with Pierre Robin sequence.

Science.gov (United States)

Buchenau, Wolfgang; Urschitz, Michael S; Sautermeister, Judit; Bacher, Margit; Herberts, Tina; Arand, Joerg; Poets, Christian F

2007-08-01

To test the hypothesis that a new orthodontic appliance with a velar extension that shifts the tongue anteriorly would reduce upper airway obstruction in infants with Pierre Robin sequence (PRS). Eleven infants with PRS (median age, 3 days) and an apnea index (AI) >3 were studied. The effect of the new appliance on the AI was compared with that of a conventional appliance without a velar extension by using a crossover study design with random allocation. Compared with baseline (mean AI, 13.8), there was a significant decrease in the AI with the new appliance (3.9; P value appliance (14.8; P = .842). Thus, the relative change in AI was -71% (95% CI, -84--49) for the new appliance and +8% (95% CI, -52-142) for the conventional appliance, which was significantly different (P = .004). No severe adverse effects were observed. This new orthodontic appliance appears to be safe and effective in reducing upper airway obstruction in infants with PRS.

Comparison of External Apical Root Resorption after Orthodontic Treatment with Two Appliances (Standard Edgewise and MBT

Directory of Open Access Journals (Sweden)

V. Mollabashi

2016-01-01

Full Text Available Introduction & Objective: The aim of this study was todeterminetheamount of external apical root resorption(EARRwithin two orthodontic appliances (standard edgewise and MBT. Material & Methods In this retrospective study, panoramic radiographs of 83 orthodontic patients (27 male and 56 female were evaluated. 46 patients had been treated with standard edgewise appliance (29 patients with extraction and 17 patients without extraction and 37 patients had been treated with MBT appliance (27 patients with extraction and 10 patients without extraction.EARR were evaluated in 24 teeth (anterior teeth, premolars and first molars in each patient. SPSS software and ordinal regression test were used for statistical analysis. Result: In this study the most EARR was seen in upper lateral incisors, then lower lateral incisors.EARR in upper canines and lower second premolars was significantly related to extraction of first premolarin MBT appliance. In non extraction cases, EARR was not related to the orthodontic appliance. Conclusion: Incisors teeth are the most disposed teeth to EARR. Orthodontic treatment with extraction increased EARR in canines and second premolars. MBT appliance may increase EARR. Sci J Hamadan Univ Med Sci . 2016; 22 (4 :316-322

Application to refrigerator plastics by mechanical recycling from polypropylene in waste-appliances

International Nuclear Information System (INIS)

Ha, Kyung Ho; Kim, Moon Saeng

2012-01-01

Highlights: → Polypropylene is mechanically recycled from waste-appliances. → Recycled polypropylene (RPP) is impact enhanced polypropylene with ethylene-propylene rubber (EPR). → Performance evaluation shows that RPP is applicable to refrigerator plastics. -- Abstract: For the application to refrigerator plastics by mechanical recycling from polypropylene (PP) in waste-appliances, it needs to identify the degradation and heterogeneity of recycled polypropylene (RPP). It is applicable the thermal analysis such as differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), spectroscopic analysis such as Fourier Transform Infrared (FTIR) and morphological analysis such as scanning electronic microscope (SEM). The analysis results show that RPP from waste-appliances is the polyethylene (PE) and polypropylene (PP) copolymer enhanced impact property (Impact-PP) and it is possible to apply refrigerator plastics with good impact property at low temperature. Finally, the performance evaluation of RPP is estimated by Gel Permeation Chromatography (GPC) analysis and is performed by the various mechanical and physical testing methods. It shows that RPP has relatively high molecular weight and balanced properties with strength and toughness. It is expected that RPP by the mechanical recycling from waste-appliances will have about 50% cost-merit.

Modeling hourly consumption of electricity and district heat in non-residential buildings

International Nuclear Information System (INIS)

Kipping, A.; Trømborg, E.

2017-01-01

Models for hourly consumption of heat and electricity in different consumer groups on a regional level can yield important data for energy system planning and management. In this study hourly meter data, combined with cross-sectional data derived from the Norwegian energy label database, is used to model hourly consumption of both district heat and electrical energy in office buildings and schools which either use direct electric heating (DEH) or non-electric hydronic heating (OHH). The results of the study show that modeled hourly total energy consumption in buildings with DEH and in buildings with OHH (supplied by district heat) exhibits differences, e.g. due to differences in heat distribution and control systems. In a normal year, in office buildings with OHH the main part of total modeled energy consumption is used for electric appliances, while in schools with OHH the main part is used for heating. In buildings with OHH the share of modeled annual heating energy is higher than in buildings with DEH. Although based on small samples our regression results indicate that the presented method can be used for modeling hourly energy consumption in non-residential buildings, but also that larger samples and additional cross-sectional information could yield improved models and more reliable results. - Highlights: • Schools with district heating (DH) tend to use less night-setback. • DH in office buildings tends to start earlier than direct electric heating (DEH). • In schools with DH the main part of annual energy consumption is used for heating. • In office buildings with DH the main part is used for electric appliances. • Buildings with DH use a larger share of energy for heating than buildings with DEH.

Custom Made Pressure Appliance for Presurgical Sustained ...

African Journals Online (AJOL)

was done to match the color of the appliance with that of the adjoining skin to make ... of the surface of the swelling with the gap between the two ... Figure 1: Preoperative view of keloid .... “multi model” approach for treating ear keloids. Indian J ...

Impact of metal and ceramic fixed orthodontic appliances on judgments of beauty and other face-related attributes.

Science.gov (United States)

Fonseca, Lílian Martins; Araújo, Telma Martins de; Santos, Aline Rôde; Faber, Jorge

2014-02-01

Physical attributes, behavior, and personal ornaments exert a direct influence on how a person's beauty and personality are judged. The aim of this study was to investigate how people who wear a fixed orthodontic appliance see themselves and are seen by others in social settings. A total of 60 adults evaluated their own smiling faces in 3 different scenarios: without a fixed orthodontic appliance, wearing a metal fixed orthodontic appliance, and wearing an esthetic fixed orthodontic appliance. Furthermore, 15 adult raters randomly assessed the same faces in standardized front-view facial photographs. Both the subjects and the raters answered a questionnaire in which they evaluated criteria on a numbered scale ranging from 0 to 10. The models judged their own beauty, and the raters assigned scores to beauty, age, intelligence, ridiculousness, extroversion, and success. The self-evaluations showed decreased beauty scores (P <0.0001) when a fixed orthodontic appliance, especially a metal one, was being worn. There was no statistically significant difference between the 3 situations in the 6 criteria analyzed. A fixed orthodontic appliance did not affect how personal attributes are assessed. However, fixed orthodontic appliances apparently changed the subjects' self-perceptions when they looked in the mirror. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 3, Water heaters, pool heaters, direct heating equipment, and mobile home furnaces

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

This is Volume 3 in a series of documents on energy efficiency of consumer products. This volume discusses energy efficiency of water heaters. Water heaters are defined by NAECA as products that utilize oil, gas, or electricity to heat potable water for use outside the heater upon demand. These are major appliances, which use a large portion (18% on average) of total energy consumed per household (1). They differ from most other appliances in that they are usually installed in obscure locations as part of the plumbing and are ignored until they fail. Residential water heaters are capable of heating water up to 180{degrees}F, although the setpoints are usually set lower.

Alteration in Taste Perception among Young Children during the use of Removable Orthodontic Appliance Therapy.

Science.gov (United States)

Razdan, Priyanka; Sakthivel, V S; Naqvi, Zuber A; Goyal, Vinod; Tripathi, Swati; Singh, Smita

2017-07-01

The sense of smell is very influential in the taste of foods. If the smell pleases us, we anticipate the taste of the food with a great deal of relish. If our sense of smell is impaired, so is our taste. The effect of appliance on taste perceptions has always had a controversial subject. The present study was designed to analyze the change in taste perception in children using removable orthodontic appliances. All the selected volunteers were given different taste stimuli and were asked to score as per their perception. The verbal score was calculated based on the correct and incorrect taste stimuli given to them. Visual analog scale was used to assess intensity and hedonic (palatability) estimation of the volunteers. The volunteers from both study and control groups scored different values for taste stimuli. The majority of stimuli were estimated correctly by both groups. There was no statistically significant difference between the study and control groups. In different testing sessions, the scoring of the volunteers was nearly constant, indicating that an appliance does not play a major role in the alteration of taste stimuli. The appliance brings about transient change in taste perception, we should educate the patient before delivering the appliance about the transient change in taste perception and encourage full-time wear of the appliance, including during meals, without fear of affecting taste sensations.

Reduction of electric power consumption in relation to household appliances. Elbesparelser ved husholdningsapparater; Forprojekt

Energy Technology Data Exchange (ETDEWEB)

Gydesen, A.

1989-07-15

Possibilities were investigated for the reduction of electric power consumption in relation to household appliances, and for cooperation with manufacturers in this respect. It is suggested that in the cases of washing-up machines, and washing and drying machines, hot water from the tap could be utilized. This would mean that the energy consumption would then shift to domestic heating equipment, dual-purpose power plants and district heating plants. Ovens, drying machines, washing machines and washing-up machines could use natural gas, especially in areas where this fuel could be conveyed to each household via pipes. Cooperation with manufacturers seems feasible, especially with regard to electric ovens, saucepans for use in combination with the latter, and water beds. Considering future developments, it is reasonable to expect that ultra sound will be utilized in connection with washing-up and washing machines, moreover it is likely that the use of enzymes in washing powders will mean that washing machines will be able to run on cold water. (AB) 21 refs.

Randomized, double-blind, placebo-controlled trial to test the efficacy of nitradine tablets in maxillary removable orthodontic appliance patients.

Science.gov (United States)

Vento-Zahra, Ethel; De Wever, Bart; Decelis, Stephen; Mallia, Kenneth; Camilleri, Simon

2011-01-01

to evaluate the efficiency of NitrAdine (MSI Laboratories) tablets in the reduction of oral Candida levels, biofilm formation, and appliance odor in maxillary removable orthodontic appliance wearers. seventy children between 11 and 15 years of age undergoing maxillary removable appliance treatment were assigned via a double-blind randomized method to the experimental or placebo arm of the study. One milliliter of unstimulated saliva was collected at the beginning of the experiment and 6 weeks later after treatment of the maxillary removable appliance with NitrAdine tablets. Samples were cultured on chromogenic Candida agar, and the number of colony-forming units per mL of saliva (CFU mL-1) was determined. there was no significant difference in salivary Candida levels before or after treatment with NitrAdine tablets. There was a significant drop in plaque accumulation on the appliance and a significant amelioration in appliance odor. There was a small, nonsignificant drop in individuals exhibiting counts of 400 CFU mL-1 or more in the experimental group and a nonsignificant increase in the number of new species in the placebo group. NitrAdine tablets are effective in reducing plaque accumulation and appliance odor during maxillary removable appliance treatment. Further in vivo studies are required to determine the efficacy and exact protocol for NitrAdine tablets in appliance disinfection.

Pendulum and modified pendulum appliances for maxillary molar distalization in Class II malocclusion - a systematic review.

Science.gov (United States)

Al-Thomali, Yousef; Basha, Sakeenabi; Mohamed, Roshan Noor

2017-08-01

The main purpose of the present systematic review was to evaluate the quantitative effects of the pendulum appliance and modified pendulum appliances for maxillary molar distalization in Class II malocclusion. Our systematic search included MEDLINE, EMBASE, CINAHL, PsychINFO, Scopus and key journals and review articles; the date of the last search was 30 January 2017. We graded the methodological quality of the studies by means of the Quality Assessment Tool for Quantitative Studies, developed for the Effective Public Health Practice Project (EPHPP). In total, 203 studies were identified for screening, and 25 studies were eligible. The quality assessment rated four (16%) of the study as being of strong quality and 21 (84%) of these studies as being of moderate quality. The pendulum appliances showed mean molar distalization of 2-6.4 mm, distal tipping of molars from 6.67° to 14.50° and anchorage loss with mean premolar and incisor mesial movement of 1.63-3.6 mm and 0.9-6.5 mm, respectively. The bone anchored pendulum appliances (BAPAs) showed mean molar distalization of 4.8-6.4 mm, distal tipping of molars from 9° to 11.3° and mean premolar distalization of 2.7-5.4 mm. Pendulum and modified pendulum appliances are effective in molar distalization. Pendulum appliance with K-loop modification, implant supported pendulum appliance and BAPA significantly reduced anchorage loss of the anterior teeth and distal tipping of the molar teeth.

Factors affecting dental biofilm in patients wearing fixed orthodontic appliances.

Science.gov (United States)

Mei, Li; Chieng, Joyce; Wong, Connie; Benic, Gareth; Farella, Mauro

2017-12-01

The aim of this study is to investigate the amount and the distribution of biofilm in patients wearing fixed appliances and its relation with age, gender, frequency of tooth brushing, and patient motivation. The sample comprised 52 patients (15.5 ± 3.6 years old, 30 females and 22 males) wearing fixed orthodontic appliances. Dental biofilm was assessed using a modified plaque index (PI). A questionnaire was used to collect patient's information, including gender, age, treatment motivation, and frequency of tooth brushing. Gingival (PI score = 0.9 ± 0.7), mesial (0.8 ± 0.6), and distal (0.8 ± 0.5) areas accumulated more biofilm than occlusal areas (0.3 ± 0.3) (P appliances have the highest biofilm accumulation on the maxillary lateral incisors and maxillary canines, particularly in the gingival area and areas behind arch wires. Less biofilm was observed in female and adult patients and in those who were self-motivated and brushed their teeth more often.

Technical Appliance in E-Learning: Student’s Perception on the Usage of Online Learning

Directory of Open Access Journals (Sweden)

Siti Sarah Mohd Johari

2010-06-01

Full Text Available The purpose of this study is to gain insights into student’s perception on the usage of technical appliances on online learning. The study took place in the Universiti Sains Malaysia (USM based on the sample of 1084 student s with the experiences of using E-learning Portal as one of the distance education academic programme. The students were surveyed on the participation needs based on respondent’s personal background, such as age, gender, ethnic groups, education streams and year-of-study. Results of the study showed even though most of the students felt uncertain about the technical appliances in E-learning Portal, the study illustrates the true nature of the student’s perceptions with respect to the functionality and effectiveness of technical appliance in E-learning Portal. This research is essential to elucidate the functions of technical appliances in facilitating the process of learning through the portal.

Les perspectives nutritionnelles offertes par les OGM en alimentation humaine

Directory of Open Access Journals (Sweden)

Pascal Gérard

2004-03-01

Full Text Available Une étude des brevets récents, des publications scientifiques ainsi que des documents présentant les projets des firmes de biotechnologie constituent la base de cet article qui présente les perspectives de développement en alimentation humaine des organismes génétiquement modifiés (OGM présentant un intérêt nutritionnel. Si l’on trouve dans les brevets et les publications scientifiques des applications qui concernent l’amélioration ou l’enrichissement de la composition en macro- et micronutriments, ces applications restent curieusement à l’état de projets, très loin de la mise sur le marché. Les critiques aussi bien que les louanges dont sont l’objet les rares cas dont on pourrait envisager une mise en œuvre à moyen terme, comme le « riz doré », sont aussi injustifiées et excessives les unes que les autres. Les violentes polémiques autour des OGM risquent de handicaper le développement d’une technique puissante, qui n’est certes pas indispensable pour apporter une solution à l’éradication de la faim dans le monde, mais qui peut apporter des améliorations à la nutrition des populations, aussi bien des populations des pays en développement que des pays développés.

46 CFR 160.031-4 - Equipment for shoulder gun type line-throwing appliance.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Equipment for shoulder gun type line-throwing appliance... Appliance, Shoulder Gun Type (and Equipment) § 160.031-4 Equipment for shoulder gun type line-throwing... the gun. The line canister shall be secured by clamps or brackets below the barrel of the gun. (c) One...

Scheduling home-appliances to optimize energy consumption

DEFF Research Database (Denmark)

Rossello Busquet, Ana

In order to optimize the energy consumption, energy demand peaks should be avoided, and energy consumption should be smoothly distributed over time. This can be achieved by setting a maximum energy consumption per user’s household. In other words, the overall consumption of the user’s appliances...

Evaluation of Musculoskeletal Disorders in Household Appliances Manufacturing Company

Directory of Open Access Journals (Sweden)

Aioob Ghanbary

2015-12-01

Full Text Available Work-related musculoskeletal disorders are the most prevalent work-related disorders and injuries and being the main cause of disability. This study was conducted to assessment of the prevalence of musculoskeletal disorders in worker company household appliances production. Posture analysis was evaluated by OWAS method and prevalence of musculoskeletal disorders by Nordic questionnaire. With evaluating musculoskeletal disorders among company household appliances production can intervention action to reduce musculoskeletal disorders was carried out. This cross-sectional study was performed on 100 workers of the appliance manufacturing industry. These Individuals were included 15 persons from foam injection workshop, 17 persons from molding workshop, 17 operators of presses, 17 persons from packaging, 17 person from cutting unit and 17 operators of rivet. The Nordic questionnaire was completed by Individuals for the organs of arm, back, leg and wrist and Posture analysis was performed by OWAS method. The data were analyzed using Spss software version 18 and descriptive statistics and Anova test. Nordic questionnaire results revealed that highest disorders were observed in the arm (25%, back (22% and leg (21%. Also Anova test showed that was observed a significant correlation respectively between age and work experience with the prevalence of musculoskeletal disorders (p<0.02 (p<0.01. The results showed based on the level of risk OWAS for each job respectively, the highest level of risk associated with foam injection unit, packaging and cutting unit (risk level 4 and the lowest level of risk associated with molding workshop unit (risk level 2.The results of this study showed that household appliances Manufacturing workers due to the nature of their jobs are at risk of musculoskeletal disorders and Ergonomic interventions to do such as workstation redesign, reduced working hours, cycle of rest-work development.

Greening production and consumption: the case of the appliance and dairy industries in Thailand

NARCIS (Netherlands)

Thongplew, N.

2015-01-01

Abstract

Natapol Thongplew

Thesis title: Greening production and consumption: The case of the appliance and dairy industries in Thailand

This research looked into the greening of the appliance and dairy industries in

Effect of dental wear, stabilization appliance and anterior tooth reconstruction on mandibular movements during speech.

Science.gov (United States)

Serrano, Priscila de Oliveira; Faot, Fernanda; Del Bel Cury, Altair Antoninha; Rodrigues Garcia, Renata Cunha Matheus

2008-01-01

This study described changes in mandibular movements during pronunciation of /m/ and /s/ sounds in Portuguese, in patients presenting dental wear before and after appliance insertion and tooth reconstruction. Subjects were divided into a control group of dentate patients and an experimental group of patients with incisal tooth wear due to bruxism. A magnetic jaw tracking device measured the jaw opening, and translations to left and right sides of the mandible during pronunciation of phonemes. Evaluations were carried out 1 week and immediately before appliance insertion; 24 h, 7, 30 and 60 days after appliance insertion; and 1 week and 1 month after tooth reconstruction. Data were submitted to two-way ANOVA, Mann-Whitney and Friedman tests (pspeech of /m/ and /s/ sounds were not changed after appliance insertion and reconstruction of teeth.

Meta-analysis of skeletal mandibular changes during Frankel appliance treatment.

Science.gov (United States)

Perillo, Letizia; Cannavale, Rosangela; Ferro, Fabrizia; Franchi, Lorenzo; Masucci, Caterina; Chiodini, Paolo; Baccetti, Tiziano

2011-02-01

The purpose of this study was to perform a meta-analysis of articles to verify the mandibular changes produced by the Fränkel-2 (FR-2) appliance during the treatment of growing patients with Class II malocclusions when compared with untreated growing Class II subjects. The literature published from January 1966 to January 2009 was reviewed with search engines. A quality analysis was performed. The effects on primary end points were calculated with random-effect models. Heterogeneity was assessed using Q statistic and investigated using study-level meta-regression. A total of nine articles were identified. The quality of the studies ranged from low to medium. Meta-analysis showed that the FR-2 was associated with enhancement of mandibular body length [0.4 mm/year 95 per cent confidence interval (CI) 0.182-0.618], total mandibular length (1.069 mm/year, 95 per cent CI 0.683-1.455), and mandibular ramus height (0.654 mm/year, 95 per cent CI 0.244-1.064). A consistent heterogeneity among studies was found for all the considered linear measurements. The FR-2 appliance had a statistically significant effect on mandibular growth. Nevertheless, the heterogeneity of the FR-2 effects, the quality of studies, the differences in age, skeletal age, treatment duration, and the inconsistent initial diagnosis seem to overstate the benefits of the FR-2 appliance. An evidence-based approach to the orthodontic outcomes of FR-2 appliance is needed, by selecting and comparing groups of children with the same cephalometric characteristics with and without treatment.

40 CFR Appendix C to Subpart F of... - Method for Testing Recovery Devices for Use With Small Appliances

Science.gov (United States)

2010-07-01

... for Use With Small Appliances C Appendix C to Subpart F of Part 82 Protection of Environment... Recovery Devices for Use With Small Appliances Recovery Efficiency Test Procedure for Refrigerant Recovery Equipment Used on Small Appliances The following test procedure is utilized to evaluate the efficiency of...

Hot air impingement on a flat plate using Large Eddy Simulation (LES) technique

Science.gov (United States)

Plengsa-ard, C.; Kaewbumrung, M.

2018-01-01

Impinging hot gas jets to a flat plate generate very high heat transfer coefficients in the impingement zone. The magnitude of heat transfer prediction near the stagnation point is important and accurate heat flux distribution are needed. This research studies on heat transfer and flow field resulting from a single hot air impinging wall. The simulation is carried out using computational fluid dynamics (CFD) commercial code FLUENT. Large Eddy Simulation (LES) approach with a subgrid-scale Smagorinsky-Lilly model is present. The classical Werner-Wengle wall model is used to compute the predicted results of velocity and temperature near walls. The Smagorinsky constant in the turbulence model is set to 0.1 and is kept constant throughout the investigation. The hot gas jet impingement on the flat plate with a constant surface temperature is chosen to validate the predicted heat flux results with experimental data. The jet Reynolds number is equal to 20,000 and a fixed jet-to-plate spacing of H/D = 2.0. Nusselt number on the impingement surface is calculated. As predicted by the wall model, the instantaneous computed Nusselt number agree fairly well with experimental data. The largest values of calculated Nusselt number are near the stagnation point and decrease monotonically in the wall jet region. Also, the contour plots of instantaneous values of wall heat flux on a flat plate are captured by LES simulation.

Mandibular advancement appliance for obstructive sleep apnoea

DEFF Research Database (Denmark)

Petri, Niels; Svanholt, Palle; Solow, Beni

2008-01-01

The aim of this trial was to evaluate the efficacy of a mandibular advancement appliance (MAA) for obstructive sleep apnoea (OSA). Ninety-three patients with OSA and a mean apnoea-hypopnoea index (AHI) of 34.7 were centrally randomised into three, parallel groups: (a) MAA; (b) mandibular non...

The International Database of Efficient Appliances (IDEA): A New Resource for Global Efficiency Policy

Energy Technology Data Exchange (ETDEWEB)

Gerke, Brian F; McNeil, Michael A; Tu, Thomas; Xu, Feiyang

2017-09-06

A major barrier to effective appliance efficiency program design and evaluation is a lack of data for determination of market baselines and cost-effective energy savings potential. The data gap is particularly acute in developing countries, which may have the greatest savings potential per unit GDP. To address this need, we are developing the International Database of Efficient Appliances (IDEA), which automatically compiles data from a wide variety of online sources to create a unified repository of information on efficiency, price, and features for a wide range of energy-consuming products across global markets. This paper summarizes the database framework and demonstrates the power of IDEA as a resource for appliance efficiency research and policy development. Using IDEA data for refrigerators in China and India, we develop robust cost-effectiveness indicators that allow rapid determination of savings potential within each market, as well as comparison of that potential across markets and appliance types. We discuss implications for future energy efficiency policy development.

Transferts thermiques dans les bassins sédimentaires Heat Transfers in Sedimentary Basins

Directory of Open Access Journals (Sweden)

Perrin J. F.

2006-11-01

Full Text Available La connaissance de l'évolution des températures dans les bassins sédimentaires est un instrument utile pour l'exploration pétrolière. En effet, connaissant la cinétique de dégradation chimique, on peut prévoir les rendements de transformation de la matière organique dans un bassin donné. La localisation des roches mères permet ensuite d'évaluer le potentiel pétrolier d'un bassin. L'étude présentée ici traite d'un modèle numérique destiné à prévoir ces champs de température tout au long de l'histoire d'un bassin, le modèle servant aussi pour l'étude des phénomènes de dog-leg thermique. Le modèle prend en compte les transferts par conduction et convection forcée (écoulement de l'eau de compaction et calcule un état des pressions et porosités. II fournit des résultats conformes aux valeurs observées in situ, et permet d'expliquer les anomalies de pressions. Knowing how temperatures have evolved in sedimentary basins is of great importance for petroleum exploration. If the chemical degradation kinetics is known, the transformation yields of organic matter can be forecast in a given basin. Then the location of source rocks can be used to evaluate the petroleum potential of a basin. This article describes a numerical model designed to determine these temperature ranges during the entire history of a basin. The model can also be used to investigate thermal dog-leg phenomena. It takes transfers by conduction and forced convection into consideration (flow of compaction water and calculates pressure and porosity conditions. The results it gives are in good agreement with values observed in situ so that various pressure anomalies can be explained.

The dynamic behaviour of heat exchangers; Etude du comportement dynamique des echangeurs de chaleur

Energy Technology Data Exchange (ETDEWEB)

Fonteray, J; Rozenholc, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1963-07-01

In order to study the dynamics of nuclear power plants, one needs mathematical models made up of ordinary differential equations. This report deals with models for heat exchangers. These models allow exact evaluations of the temperatures for any steady state. The deformation of the temperature maps during transients is taken into account. To do this, average temperatures are evaluated keeping In mind, on one hand the partial differential equations, on the other hand, the physical phenomenons which are involved. Seven ordinary differential equations at most, are necessary for one heat exchanger. Theses models were compared with mathematically exact ones and also with experimental results, that EDF was able to measure on EDF-1 heat exchangers. The results appear to be correct. (authors) [French] Les etudes de dynamique sur les centrales nucleaires exigent l'elaboration de modeles apparaissant sous forme d'equations differentlelles ordinaires. Ce rapport est consacre a la recherche de modeles d'echangeurs. Dans ces modeles les temperatures sont calculees exactement pour n'importe quel regime permanent. Pour tenir compte de la deformation des distributions de temperature en regime transitoire, on evalue les temperatures moyennes dans l'echangeur en s'appuyant, d'une part, sur les equations aux derivees partielles et, d'autre part, sur une analyse des phenomenes physiques. Les modeles contiennent au plus sept equations differentielles ordinaires. Ces modeles ont ete compares aux modeles mathematiques exacts et aussi a des resultats experimentaux, obtenus par l'EDF, sur les echangeurs d'EDF-1. Les resultats paraissent satisfaisants. (auteurs)

Clinical Effectiveness of Using Aesthetic Fixed Prosthetic Appliances with Combined Occlusal Surface

Directory of Open Access Journals (Sweden)

Andrii Biben

2017-06-01

Conclusions. Aesthetic fixed prosthetic appliances with combined occlusal surface demonstrated high functional and aesthetic characteristics. The use of the USHPS system showed a decisive advantage of milled frameworks and combined occlusal surface over traditional cast ceramic frameworks.The combination of high mechanical, strength and tribological properties of zirconium dioxide and high biological as well as aesthetic properties of ceramic materials helped reveal high clinical characteristics of aesthetic appliances with combined occlusal surface.

Gas at work. Vision on decentralized gas appliances in the built environment

International Nuclear Information System (INIS)

Van Gastel, M.; Hooijschuur, J.; De Jong, A.; De Visser, I.; Overdiep, H.; Bakker, E.J.; Van Wolferen, H.

2008-04-01

Various platforms operate within the SenterNovem programme Creative Energy. This report is the first version of the vision document of the working group Decentralized gas appliances of the Platform New Gas, in which the following aspects of the various promising innovative gas appliances are indicated: the development stage, the intended energy saving, the CO2 reduction, the bottlenecks for large scale market introduction and the solutions for these bottlenecks. [mk] [nl

Thermally accurate LES of the stability-emission performance of staged gas-turbine combustion; Simulation aux grandes echelles de la combustion etagee dans les turbines a gaz et son interaction stabilite-polluants-thermique

Energy Technology Data Exchange (ETDEWEB)

Schmitt, P.

2005-06-15

Modern gas turbines use turbulent lean partially premixed combustion in order to minimise nitrous oxide (NO{sub X}) emissions while ensuring flashback safety. The Large-Eddy Simulation (LES) of such a device is the goal of this work. Focus is laid on correctly predicting the NO{sub X} emissions, which are influenced by four factors: heat transfer, mixing quality, combustion modelling and thermo-acoustic stability. As NO{sub X} reaction rates are strongly influenced by temperature, heat transfer by radiation and convection is included. Radiation is predicted by a model, which assumes that the gases are optically thin. Convective heat transfer is included via a newly developed and validated wall-function approach based on the logarithmic law of the wall for temperature. An optimised 2-step reduced chemical reaction scheme for lean methane combustion is presented. This scheme is used for the LES in conjunction with an additional third reaction, fitted to produce the same NO{sub X} reaction rates as in the complete reaction mechanism. Turbulence is accounted for with the thickened flame model in a form, which is optimised for changing equivalence ratios and mesh-resolutions. Mixing is essential not only for predicting flame stabilisation, but also for pollutant emissions as NO{sub X} reaction rates depend exponentially on equivalence ratio. Therefore the full burner geometry, including 16 fuel injections is resolved in LES. Additionally, effusion cooling and film cooling is accounted for in a simplified manner. The non-reacting flow is extensively validated with experimental results. As mixture-fraction fluctuations do not only arise from turbulence, but also from thermo-acoustic instabilities, care was taken to provide acoustic boundary conditions that come close to reality. The resulting LES shows a strong thermo-acoustic instability, comparing well with experimental observations. By making the boundaries completely anechoic it is shown that when the instability

Assessment of the rate of premolar extraction space closure in the maxillary arch with the AcceleDent Aura appliance vs no appliance in adolescents: A single-blind randomized clinical trial.

Science.gov (United States)

Miles, Peter; Fisher, Elizabeth; Pandis, Nikolaos

2018-01-01

The purpose of this 2-arm parallel trial was to assess the effect of the AcceleDent Aura appliance (OrthoAccel Technologies, Houston, Tex) on the rate of maxillary premolar extraction space closure in adolescent patients. Forty Class II adolescents treated with full fixed appliances and maxillary premolar extractions participated in this randomized clinical trial. They were recruited in a private practice and treated by 1 clinician. Randomization was accomplished in blocks of 10 patients assigned to either a no-appliance group or the AcceleDent Aura appliance group with the allocations concealed in opaque, sealed envelopes. Both the operator and the outcome assessor were blinded; however, it was not feasible to blind the patients. Models were taken of the maxillary arch at the start of space closure and just before complete space closure. The space was measured parallel to the occlusal plane from the cusp tips of the teeth mesial and distal to the extraction spaces. There was no clinically (0.05 mm per month; 95% confidence interval [CI], -0.24, 0.34) or statistically significant difference in the rate of space closure (P = 0.74). In both the univariable and multivariable analyses, the mean rate of tooth movement was slower by 0.13 mm per month (95% CI, -.26, .005) on the left side compared with the right side, but this was not statistically significant (P = 0.06). The AcceleDent Aura appliance had no effect on the rate of maxillary premolar extraction space closure. Only a few participants were considered to be good compliers with the appliance. However, the rate of space closure in the good compliers was similar to the overall group and did not appear to influence the result. This trial was not registered. The protocol was not published before trial commencement. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Interceptive Correction of Anterior Crossbite Using Short-Span Wire-Fixed Orthodontic Appliance: A Report of Three Cases

Directory of Open Access Journals (Sweden)

S. Nagarajan M. P. Sockalingam

2018-01-01

Full Text Available Anterior crossbite is relatively a common presentation in the mixed dentition stage. If left untreated, it can lead to a host of problems and may complicate future orthodontic treatment. One of the major difficulties in performing anterior crossbite correction in young children is treatment compliance. In most cases, poor compliance is due to the unacceptability of the removable appliance used. This article describes three cases of successful correction of anterior crossbite of patients in mixed dentition using short-span wire-fixed orthodontic appliances. This sectional appliance provides an alternative method of correcting anterior crossbite of dental origin and offers many advantages compared to the use of removable appliances.

Esthetic perception and economic value of orthodontic appliances by lay Brazilian adults

Directory of Open Access Journals (Sweden)

Daniela Feu

2012-10-01

Full Text Available OBJECTIVE: To evaluate the esthetic perception of different appliances by Brazilian lay adults and its influence in the attributed value of orthodontic treatment, considering evaluators' socioeconomic status, age and gender. METHODS: Eight different combinations of orthodontic appliances and clear tray aligners were placed in a consenting adult with pleasing smile. Standardized frontal photographs were captured and incorporated into a research album. A sample of adults (n = 252, median = 26 years old were asked to rate each image for (1 its attractiveness on a visual analog scale and (2 the willingness to pay (WTP for a cosmetic appliance when compared to a standard metalic appliance and a clear tray aligner. Comparisons between the appliances' attractiveness were performed using the Friedman's test and Dann's post-hoc test. Correlation between appliances' attributed value, socioeconomic status, age, gender, and esthetic perception was assessed using Spearman's correlation analysis. RESULTS: Attractiveness ratings of orthodontic appliances varied significantly in the following hierarchy: Clear aligners>sapphire brackets>self-ligating/conventional stainless steel brackets>and golden metal appliances. The correlation between WTP and esthetic perception was week. However, for individuals with better socioeconomic status and aged between 17-26 years old significantly, a significantly higher WTP was found. CONCLUSION: Clear aligners and sapphire brackets with esthetic archwire were considered better esthetic options in this sample. Nevertheless, patients were not willing to pay more money for appliances they deemed more esthetic, however, they were significantly influenced by their socioeconomic level and age.OBJETIVO: avaliar a percepção de brasileiros adultos leigos para diferentes aparelhos ortodônticos e sua influência na valorização econômica do tratamento, considerando o nível socioeconômico, idade e sexo dos avaliadores. M�

Homogenization of a Conductive-Radiative Heat Transfer Problem

Directory of Open Access Journals (Sweden)

Habibi Zakaria

2012-04-01

Full Text Available This paper focuses on the contribution of the second order corrector in periodic homogenization applied to a conductive-radiative heat transfer problem. Especially, for a heat conduction problem in a periodically perforated domain with a non-local boundary condition modelling the radiative heat transfer, if this model contains an oscillating thermal source and a thermal exchange with the perforations, the second order corrector helps us to model the gradients which appear between the source area and the perforations. Ce papier est consacré à montrer l’influence du correcteur de second ordre en homogénéisation périodique. Dans l’homogénéisation d’un problème de conduction rayonnement dans un domaine périodiquement perforé par plusieurs trous, on peut voir une contribution non négligeable de ce correcteur lors de la présence d’une source thermique oscillante et d’un échange thermique dans les perforations. Ce correcteur nous permet de modéliser les gradients qui apparaissent entre la zone de la source thermique et les perforations.

Les brulures electriques chez les voleurs de cuivre

Science.gov (United States)

Belmir, R.; Fejjal, N.; Achbouk, H.; El Mazouz, S.; Gharib, N.; Abassi, A.; Belmahi, A.

2011-01-01

Summary Les vols de biens fabriqués avec le cuivre semblent en hausse depuis un certain temps du fait de son prix élevé de revente, ce qui est à l’origine d’une augmentation du nombre d’accidents électriques par haut voltage (AEHV) qui sont graves du fait des brûlures profondes qu’elles provoquent le long des axes vasculo-nerveux. Les Auteurs rapportent une série de neuf cas d’AEHV traités au service de chirurgie plastique et de brûlés de l’Hôpital Ibn Sina de Rabat, Maroc, à travers laquelle ils étudient les caractéristiques épidémiologiques, cliniques et thérapeutiques. La population intéressée était jeune et active. Les brûlures étaient secondaires à un contact avec des câbles à haute tension lors de tentatives de vol par arrachement de conducteurs en cuivre dans les transformateurs dans 67% des cas, et lors de tentatives de coupure de caténaires alimentant les trains électriques sur le réseau ferroviaire dans 33% des cas. Le traitement des lésions électrothermiques a nécessité des interventions itératives avec amputation et désarticulation des segments de membres nécrosés dans 66% des cas, dont les suites étaient marquées par des séquelles fonctionnelles invalidantes. La prévention de ce type d’AEHV reste fondamentale. PMID:22262961

Real-Time Recognition Non-Intrusive Electrical Appliance Monitoring Algorithm for a Residential Building Energy Management System

Directory of Open Access Journals (Sweden)

Kofi Afrifa Agyeman

2015-08-01

Full Text Available The concern of energy price hikes and the impact of climate change because of energy generation and usage forms the basis for residential building energy conservation. Existing energy meters do not provide much information about the energy usage of the individual appliance apart from its power rating. The detection of the appliance energy usage will not only help in energy conservation, but also facilitate the demand response (DR market participation as well as being one way of building energy conservation. However, energy usage by individual appliance is quite difficult to estimate. This paper proposes a novel approach: an unsupervised disaggregation method, which is a variant of the hidden Markov model (HMM, to detect an appliance and its operation state based on practicable measurable parameters from the household energy meter. Performing experiments in a practical environment validates our proposed method. Our results show that our model can provide appliance detection and power usage information in a non-intrusive manner, which is ideal for enabling power conservation efforts and participation in the demand response market.

Evaluation of temporomandibular disorders in Class III patients treated with mandibular cervical headgear and fixed appliances.

Science.gov (United States)

Rey, Diego; Oberti, Giovanni; Baccetti, Tiziano

2008-03-01

Our aim in this study was to evaluate the prevalence of temporomandibular disorders (TMD) in Class III patients treated with mandibular cervical headgear (MCH) and fixed appliances. The sample of 75 patients included 25 patients with no previous orthodontic treatment, 25 Class I patients who had undergone orthodontic treatment with fixed appliances and without extractions, and 25 patients with dentoskeletal Class III disharmonies treated with MCH and fixed appliances. The Helkimo index was used to test the prevalence of TMD symptoms in the 3 groups. The prevalence rates of the Helkimo index in the 3 groups were compared with the z score on proportions. No statistically significant differences in the prevalence rates of the Helkimo index scores in the 3 groups were found (P = .367). Most subjects in the 3 groups had an Helkimo index of zero (66.7%). Subjects with Class III malocclusions treated with MCH and fixed appliances do not have greater prevalence of TMD symptoms than do Class I subjects treated with fixed appliances or untreated subjects.

Energy Efficiency: The Implementation of Minimum Energy Performance Standard (MEPS Application on Home Appliances for Residential

Directory of Open Access Journals (Sweden)

Rahman K.A

2016-01-01

Full Text Available Generally, Minimum Energy Performance Standard (MEPS has been widespread across the country especially developed country. However, most consumers do not even know about the MEPS. Without sufficient knowledge, much energy have been wasted before this. The aim of this study is to review the implementation of MEPS of Asia country and to compare electricity consumption of home appliances with star rating and without star rating. In order to fulfil the objectives of the study, the equipment must be chosen correctly and must be learned properly. The home appliances that will be used also need to be chosen so that the comparison between the appliances will be matched correctly. To understand the results, the analysis was done using graphs and table. The purpose of using graph and table is to understand the comparison between appliances more clearly. The results show that home appliances with MEPS is more efficient on energy saving rather than without MEPS. This is the evidence as a method to educate a consumer on energy saving.

Dentoalveolar and skeletal changes associated with the pendulum appliance followed by fixed orthodontic treatment.

Science.gov (United States)

Angelieri, Fernanda; Almeida, Renato Rodrigues de; Almeida, Marcio Rodrigues de; Fuziy, Acácio

2006-04-01

This prospective clinical study analyzed the distalization of maxillary molars achieved by the pendulum appliance and its effect on the anchorage teeth during and after fixed orthodontic treatment. Lateral cephalograms of 22 adolescents (15 girls, 7 boys) taken pretreatment, after distalization, after leveling and aligning, and after fixed orthodontic treatment were evaluated. The initial mean age was 14.5 years (SD = 1.80). The mean time for distalization of the maxillary molars was 5.85 months (SD = 1.82), and the total treatment time was 3.61 years (SD = 1.83). The pendulum appliance moved the maxillary molars distally, but with significant distal inclination, protrusion of the anterior teeth, and increase in lower anterior facial height (LAFH) due to the clockwise mandibular rotation. After fixed orthodontic treatment, the maxillary incisors and the maxillary first premolars and first molars were returned to their pretreatment anteroposterior positions. Thus, at postdistalization, there was 2.1 mm of protrusion of the maxillary first molars, despite the anchorage reinforcement (Nance button and cervical headgear worn at night during fixed appliance therapy). However, at the end of treatment, all patients had Class I molar relationships. The pendulum appliance followed by fixed orthodontic treatment corrected the Class II sagittal relationship, especially due to the dentoalveolar changes secondary to the spontaneous mandibular growth in the anterior direction during fixed appliance treatment.

Hoisting appliances and fuel handling equipment at nuclear facilities

International Nuclear Information System (INIS)

1987-01-01

The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection

Improvement of heat transfer to gases by mean of electric fields (1962); Etude de l'amelioration des echanges de chaleur dans les gaz au moyen de champs electriques (1962)

Energy Technology Data Exchange (ETDEWEB)

NONE

1962-07-01

The effects of electric fields on heat transfer to the following gases: air, argon, nitrogen, carbon dioxyde, helium, hydrogen, were studied in an annular channel, the inner part of which is the heating element. Experiments were made both in free convection and forced convection, the latter case with and without an external source of ionisation. Two causes of improvement of heat transfer were found: electro-convection and ionic convection; the influence of various parameters (electric fields, current of ionisation, temperatures, pressures, flow rate, etc...) is also investigated. Increasing of exchanged power was measured: in free convection this increasing reached 400 per cent and, in forced convection, it was found to be mainly dependent on stream velocity, decreasing from 300 per cent at Re = 6000 to few per cent for Re {>=} 30000 for a given gas pressure. Experiments in pile have shown that the use of an external source of ionisation allowed to obtain the same order of improvement as above but with a voltage much lower. This fact would make easier the use of this process of heat transfer in a channel of a reactor. (authors) [French] On a etudie l'action du champ electrique sur les echanges de chaleur dans les gaz suivants: air, argon, azote, anhydride carbonique, helium, hydrogene, avec un element chauffant cylindrique dans un canal concentrique. Des experiences ont ete effectuees en convection libre et en convection forcee en l'absence et en presence d'une source exterieure d'ionisation. On a distingue deux sortes de mecanismes d'accroissement des echanges, l'un d'electroconvection proprement dite et l'autre de convection ionique, et on precise l'influence des divers parametres (champ electrique, courant d'ionisation, temperature, pression, debit, etc...). On a pu chiffrer les ordres de grandeur des accroissements d'echanges observes qui, en convection libre, atteignent 300 a 400 pour cent et, en convection forcee, dependent beaucoup de la vitesse d

Cl II Malocclusion Treatment, Using the Modified Twin Block Appliance Coordinated with Fixed Orthodontics in a Postmenarche Patient

Directory of Open Access Journals (Sweden)

Amin Aminian

2017-01-01

Full Text Available Functional appliances have been used for treatment of Class II patients for a long time. The main objective of therapy with functional appliances is to induce supplementary lengthening of the mandible by stimulating increased growth at the condylar cartilage. The Twin Block appliance is one of the most commonly used functional appliances. The aim of this paper is to present a case report of mandibular deficiency treatment with Twin Block appliance in a female patient whose sexual maturation (one and a half years after menarche and cervical vertebral maturation stage indicated the end of the growth peak. The treatment started with bonding 0.022 in MBT prescription brackets on the upper arch in order to align upper teeth and create a symmetric overjet. When reaching alignment, a modified Twin Block was given to the patient for 8 months. Final coordination was achieved with fixed appliances in both arches. At the end of the treatment, profile of the patient improved, crowding was relieved, and Cl I relationship with normal overjet and overbite was achieved.

Cone beam computed tomography study of apical root resorption induced by Herbst appliance

Science.gov (United States)

SCHWARTZ, João Paulo; RAVELI, Taísa Boamorte; ALMEIDA, Kélei Cristina de Mathias; SCHWARTZ-FILHO, Humberto Osvaldo; RAVELI, Dirceu Barnabé

2015-01-01

Objective This study evaluated the frequency of root resorption during the orthodontic treatment with Herbst appliance by Cone Beam Computed Tomography (CBCT). Material and Methods The sample comprised 23 patients (11 men, 12 women; mean ages 15.76±1.75 years) with Class II division 1 malocclusion, treated with Herbst appliance. CBCT was obtained before treatment (T0) and after Herbst treatment (T1). All the dental roots, except third molars, were evaluated, and apical root resorption was determined using the axial guided navigation method. Paired t-tests and Wilcoxon T Test were used to compare the dependent samples in parametric and nonparametric cases, respectively. Chi-Square Test with Yates’ correction was used to evaluate the relationship between apical root resorption and gender. Results were considered at a significance level of 5%. Results Apical resorption was detected by CBCT in 57.96% of 980 roots that underwent Herbst appliance treatment. All patients had minimal resorption and there was no statistical significance between the genders. Conclusion CBCT three-dimensional evaluation showed association between Herbst appliance and minimal apical root resorption, mostly in the anchoring teeth, without clinical significance. PMID:26537718

Cone beam computed tomography study of apical root resorption induced by Herbst appliance

Directory of Open Access Journals (Sweden)

João Paulo SCHWARTZ

2015-10-01

Full Text Available Objective This study evaluated the frequency of root resorption during the orthodontic treatment with Herbst appliance by Cone Beam Computed Tomography (CBCT.Material and Methods The sample comprised 23 patients (11 men, 12 women; mean ages 15.76±1.75 years with Class II division 1 malocclusion, treated with Herbst appliance. CBCT was obtained before treatment (T0 and after Herbst treatment (T1. All the dental roots, except third molars, were evaluated, and apical root resorption was determined using the axial guided navigation method. Paired t-tests and Wilcoxon T Test were used to compare the dependent samples in parametric and nonparametric cases, respectively. Chi-Square Test with Yates’ correction was used to evaluate the relationship between apical root resorption and gender. Results were considered at a significance level of 5%.Results Apical resorption was detected by CBCT in 57.96% of 980 roots that underwent Herbst appliance treatment. All patients had minimal resorption and there was no statistical significance between the genders.Conclusion CBCT three-dimensional evaluation showed association between Herbst appliance and minimal apical root resorption, mostly in the anchoring teeth, without clinical significance.

Refrigerator efficiency in Ghana: Tailoring an appliance market transformation program design for Africa

International Nuclear Information System (INIS)

Van Buskirk, Robert; Ben Hagan, Essel; Ofosu Ahenkorah, Alfred; McNeil, Michael A.

2007-01-01

In some cases, a simple replication of developed country appliance efficiency labels and standards may not be completely feasible in Ghana, Africa. Yet by creatively modifying the developed country appliance efficiency market transformation model, it should be possible to achieve dramatic energy use reductions. As was true in developed countries in the previous two decades, refrigeration efficiency improvements provide the greatest energy savings potential in the residential electricity sector in Ghana. Although Ghana, like many African countries may impose standards on imports since Ghana does not have manufacturing facilities for appliances in country. This approach may hurt some consumers who patronize a very diverse market of used appliances imported from Europe. We discuss how meeting the challenges of the Ghanaian market will require modification of the usual energy efficiency labeling and standards paradigm. But once a refrigerator market transformation is accomplished in Ghana, we estimate an average energy savings potential of 550 kWh/refrigerator/year, and a monetary savings of more than $35/refrigerator/year. We discuss how this modified refrigerator efficiency market transformation may occur in the Ghanaian context. If successful, this market transformation is likely to be an example for many other African countries

Effect of fixed orthodontic appliances on salivary microbial parameters at 6 months: a controlled observational study

Directory of Open Access Journals (Sweden)

Delphine MARET

2014-01-01

Full Text Available Objective: The aim of this study was to assess the microbial changes in children with fixed orthodontic appliances compared with a control group of children without orthodontic treatment. Material and Methods: Ninety-five children, aged between 12 and 16 years, participated in this study. Forty-eight subjects were fitted with fixed orthodontic appliances and forty-seven were free of any such appliances. The follow-up was 6 months for all children. The association between orthodontic appliances and high levels of Streptococcus mutans and Lactobacillus spp was assessed with logistic regression models, taking age, sex, pH and buffer capacity into account. Results: Differences at baseline between the two groups were not statistically significant. We found that wearing a fixed orthodontic appliance was associated with high levels of Streptococcus mutans and Lactobacillus spp (adjusted OR: 6.65, 95% CI [1.98-22.37]; 9.49, 95% CI [2.57-35.07], respectively, independently of other variables. Conclusion: The originality of the present epidemiological study was to evaluate the evolution of salivary microbial parameters in a population of children with fixed orthodontic appliances. Our results show an increase of Streptococcus mutans and Lactobacillus spp values during the follow-up. The whole dental workforce should be aware that preventive measures are of paramount importance during orthodontic treatment.

International comparison of product certification and verification methods for appliances

Energy Technology Data Exchange (ETDEWEB)

Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-06-01

Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

International Comparison of Product Certification and Verification Methods for Appliances

Energy Technology Data Exchange (ETDEWEB)

Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-06-01

Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

Tree-crown-resolving large-eddy simulation for evaluating greenery effects on urban heat environments

Science.gov (United States)

Matsuda, K.; Onishi, R.; Takahashi, K.

2017-12-01

Urban high temperatures due to the combined influence of global warming and urban heat islands increase the risk of heat stroke. Greenery is one of possible countermeasures for mitigating the heat environments since the transpiration and shading effect of trees can reduce the air temperature and the radiative heat flux. In order to formulate effective measures, it is important to estimate the influence of the greenery on the heat stroke risk. In this study, we have developed a tree-crown-resolving large-eddy simulation (LES) model that is coupled with three-dimensional radiative transfer (3DRT) model. The Multi-Scale Simulator for the Geoenvironment (MSSG) is used for performing building- and tree-crown-resolving LES. The 3DRT model is implemented in the MSSG so that the 3DRT is calculated repeatedly during the time integration of the LES. We have confirmed that the computational time for the 3DRT model is negligibly small compared with that for the LES and the accuracy of the 3DRT model is sufficiently high to evaluate the radiative heat flux at the pedestrian level. The present model is applied to the analysis of the heat environment in an actual urban area around the Tokyo Bay area, covering 8 km × 8 km with 5-m grid mesh, in order to confirm its feasibility. The results show that the wet-bulb globe temperature (WBGT), which is an indicator of the heat stroke risk, is predicted in a sufficiently high accuracy to evaluate the influence of tree crowns on the heat environment. In addition, by comparing with a case without the greenery in the Tokyo Bay area, we have confirmed that the greenery increases the low WBGT areas in major pedestrian spaces by a factor of 3.4. This indicates that the present model can predict the greenery effect on the urban heat environment quantitatively.

Impact of Natural Gas Appliances on Pollutant Levels in California Homes

Energy Technology Data Exchange (ETDEWEB)

Mullen, Nasim A.; Li, Jina; Singer, Brett C.

2012-12-01

This report presents results from the first year of a 2-year study, investigating associations of five air pollutants (CO, NO2, NOX, formaldehyde and acetaldehyde) with the presence of natural gas appliances in California homes. From November 2011 to March 2012, pollutant concentration and occupant activity data were collected in 155 homes for 6-day periods. The sample population included both single-family (68%) and multi-family (32%) dwellings, with 87% having at least one gas appliance and 77% having an unvented gas cooking appliance. The geometric mean (GM) NO2 levels measured in the kitchen, bedroom and outside of homes were similar at values of 15, 12 and 11 ppb, respectively. In contrast, the GM NOx levels measured in the kitchen and bedroom of homes were much higher than levels measured outdoors, at levels of 42 and 41 ppb, compared to 19 ppb, respectively. Roughly 10% of sampled homes had 6-day average NO2 levels that exceeded the outdoor annual average limit set by the California Ambient Air Quality Standards (CAAQS) (30 ppb). The GMs of the highest 1-h and 8-h CO level measured in homes were 2.5 and 1.1 ppm, respectively. Four homes had a 1-h or 8-h concentration that exceeded the outdoor limits set by the CAAQS. The GM formaldehyde and acetaldehyde concentrations measured in homes were 15 and 7 ppb, respectively. Roughly 95% of homes had average formaldehyde levels indoors that exceeded the Chronic Reference Exposure Level set by the California EPA (7 ppb). Concentrations of NO2 and NOx, and to a lesser extent CO were associated with use of gas appliances, particularly unvented gas cooking appliances. Based on first principles, it is expected that effective venting of cooking pollutant emissions at the source will lead to a reduction of pollutant concentrations. However, no statistical association was detected between kitchen exhaust fan use and pollutant concentrations in homes in this study where gas cooking occurred frequently. The lack of

Do you do Damon®? What is the current evidence base underlying the philosophy of this appliance system?

Science.gov (United States)

Wright, Natasha; Modarai, Faranak; Cobourne, Martyn T; Dibiase, Andrew T

2011-09-01

Self-ligating bracket systems are increasing in popularity amongst orthodontists. This reflects their high quality engineering, improved reliability and relative ease of use. However, it might also be related to claims of superior function made by the manufacturers of these appliances. In particular, the Damon(®) appliance system claims to offer significant advantages to both orthodontist and patient over conventional-ligation and other forms of self-ligated appliances. We have reviewed current literature relating to use of the Damon(®) appliance system. There is some evidence to suggest this appliance may lead to reductions in chairside time for the orthodontist, particularly those experienced with this system, in comparison to conventional-ligation. However, evidence that pain experience is reduced for the patient when using Damon(®) brackets is not conclusive. In the presence of identical archwire sequences, there is no evidence that Damon(®) brackets can align teeth faster or in a qualitatively differently manner, when compared with conventional-ligation. There is no high quality evidence that treatment with the Damon(®) appliance takes place more rapidly or leads to a superior occlusal or aesthetic result. Indeed, the best available evidence would suggest there is no difference in treatment outcome or time, at least in extraction cases. There is no evidence that treatment with the Damon(®) appliance is more stable. Claims relating to improved clinical performance of the Damon(®) appliance system are currently being made to orthodontists and patients that are not substantiated in the scientific literature.

Clean energy, technical files; Energie propre, les fiches techniques

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

This document is the compilation of the 42 issues of the 'Energie propre - Maitrise de la Demande d'Energie' newsletter published between September 1996 and July 1999 by the regional energy agency of Provence-Alpes-Cote d'Azur region (ARENE). Each issue is a technical file presenting a particular action or study carried out in the framework of the program of mastery of energy demand in Provence-Alpes-Cote d'Azur region (SE France). These studies and actions concern various types of buildings: high schools, residential buildings for old people, office buildings, social buildings, hotels, recreational facilities, and cover all aspects of energy conservation: space heating, lighting systems, ventilation systems, thermal insulation, appliances.. (J.S.)

Les risques du travail

CERN Document Server

Thébaud-Mony, Annie

2015-01-01

Depuis les années 1990, les conditions de travail se sont peu à peu imposées dans le débat social. Néanmoins, la situation reste critique. Les risques traditionnels n'ont pas disparu : les manutentions lourdes, l'exposition professionnelle aux cancérogènes, au bruit ou aux vibrations demeurent répandues... De plus, certaines " améliorations " n'ont fait que déplacer et dissimuler les problèmes, telle l'externalisation des risques grâce à la sous-traitance. Dans le même temps, les transformations du travail et des modalités de gestion de la main-d'œuvre ont fragilisé les collectifs et accru l'isolement des salariés, conduisant à une montée visible de la souffrance psychique. Face à ces évolutions, il est plus que jamais nécessaire que tous les acteurs concernés, en particulier les salariés eux-mêmes et leurs représentants, s'approprient les connaissances indispensables pour améliorer la protection de la santé sur les lieux du travail. Tel est le but de ce livre, qui renouvelle int�...

Space Maintenance with an Innovative ?Tube and Loop? Space Maintainer (Nikhil Appliance)

OpenAIRE

Srivastava, Nikhil; Grover, Jyotika; Panthri, Prerna

2016-01-01

ABSTRACT Despite the best efforts in prevention, premature loss of primary teeth continues to be a common problem in pediatric dentistry, resulting in disruption of arch integrity and adversely affecting the proper alignment of permanent successors. Space maintainers (SMs) are special appliances used for maintaining space created due to premature loss of primary teeth. Band and loop SM is mostly indicated for the premature loss of single primary molar, but this appliance has a number of limit...

A new modified tandem appliance for management of developing Class III malocclusion

OpenAIRE

Sukh, Ram; Singh, Gyan P; Tandon, Pradeep

2013-01-01

Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior...

Impact of wearing fixed orthodontic appliances on quality of life among adolescents: Case-control study.

Science.gov (United States)

Costa, Andréa A; Serra-Negra, Júnia M; Bendo, Cristiane B; Pordeus, Isabela A; Paiva, Saul M

2016-01-01

To investigate the impact of wearing a fixed orthodontic appliance on oral health-related quality of life (OHRQoL) among adolescents. A case-control study (1 ∶ 2) was carried out with a population-based randomized sample of 327 adolescents aged 11 to 14 years enrolled at public and private schools in the City of Brumadinho, southeast of Brazil. The case group (n  =  109) was made up of adolescents with a high negative impact on OHRQoL, and the control group (n  =  218) was made up of adolescents with a low negative impact. The outcome variable was the impact on OHRQoL measured by the Brazilian version of the Child Perceptions Questionnaire (CPQ 11-14) - Impact Short Form (ISF:16). The main independent variable was wearing fixed orthodontic appliances. Malocclusion and the type of school were identified as possible confounding variables. Bivariate and multiple conditional logistic regressions were employed in the statistical analysis. A multiple conditional logistic regression model demonstrated that adolescents wearing fixed orthodontic appliances had a 4.88-fold greater chance of presenting high negative impact on OHRQoL (95% CI: 2.93-8.13; P appliances. A bivariate conditional logistic regression demonstrated that malocclusion was significantly associated with OHRQoL (P  =  .017), whereas no statistically significant association was found between the type of school and OHRQoL (P  =  .108). Adolescents who wore fixed orthodontic appliances had a greater chance of reporting a negative impact on OHRQoL than those who did not wear such appliances.

Disposal machine using a hydraulic shovel loader for waste home electric appliances; Yuatsu shoberunado wo katsuyoshita haikaden shori kikai

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-25

This paper presents a disposal machine system developed by Hitachi Kenki Co. for waste home appliances. EX60 disposal machine and 2-axis shear shredder were developed as work machines for volume reduction and efficient disposal of waste home appliances. The shredder with rotary cutters is featured by superior crunch performance and efficient shredding of waste home appliances, and can crash not only waste home appliances but also various objects such as bulky waste, waste plastics and waste tire for passenger cars at crash torques from 7000 to 12000kgf{center_dot}m. The shredder is featured by superior mobility and easy operability by self-running and full-hydraulic driving, low- noise engine, and noise/vibration reduction by low-speed large torque hydraulic motor. EX60 disposal machine has clamp fixing waste home appliances, and a grapple for disassembling and classification, and can efficiently disassemble and classify 4 kinds of waste home appliances and other wastes only by itself. 12 figs., 3 tabs.

Comment scolariser les enfants Roms? Les enfants Roms dans les dispositifs mis en place à Bordeaux Métropole.

OpenAIRE

Øhlund, Ida

2016-01-01

Dans ce mémoire, je m intéresse à la scolarisation des enfants Roms en France. Je présente la place des enfants Roms dans la scolarisation en Europe et en France. Je discute les efforts qu on fait en France pour scolariser ces enfants, et je prends comme exemple les mesures d intégration prises par les autorités de Bordeaux Métropole en expliquant les rôles des différents acteurs locaux. Dans la première partie, j essaye de présenter le groupe minoritaire européen appelé « Rom ». J aborde l h...

Low-power Appliance Recognition using Recurrent Neural Networks

NARCIS (Netherlands)

Rizky Pratama, Azkario; Simanjuntak, Frans Juanda; Lazovik, Aliaksandr; Aiello, Marco

2018-01-01

Indoor energy consumption can be understood by breaking overall power consumption down into individual components and appliance activations. The clas- sification of components of energy usage is known as load disaggregation or ap- pliance recognition. Most of the previous efforts address the

Analysis appliance by gamma tomography with focused collimators

International Nuclear Information System (INIS)

Stoddart, H.F.

1978-01-01

This invention concerns nuclear medicine and specifically an image-forming appliance providing a very sensitive quantitative determination and the localization in space of the radioactivity of a body organ such as the brain of a patient to whom a substance labelled with radioactive isotopes has been administered. The characteristics of this appliance, which forms an image in a transversal scanning field by means of radioactive isotope radiations, includes several highly focused collimators, placed in line and focused inwards so that they form an arrangement that surrounds a given scanning field. Each collimator is mobile with respect to the adjacent collimator and a system moves the collimators so that the focus of each one uniformly samples at least a half of the total scanning field corresponding to a cross section. The number of detectors is an even one between two and twenty four, and the collimators are twelve in number [fr

Production of dry wood chips in connection with a district heating plant

Directory of Open Access Journals (Sweden)

Yrjölä Jukka

2004-01-01

Full Text Available Moisture and its variation in wood chips make the control of burning in small scale heating appliances difficult resulting in emissions and loss of efficiency. If the quality of wood chips would be better, i. e. dried and sieved fuel with more uniform size distribution would be avail able, the burning could be much cleaner and efficiency higher. In addition higher power out put could be obtained and the investment costs of the burning appliances would be lower. The production of sieved and dried wood chip with good quality could be accomplished in connection with a district heating plant. Then the plant would make profit, in addition to the district heat, from the dried wood chips sold to the neighboring buildings and enterprises sep a rated from the district heating net using wood chips in energy production. The peak power of a district heating plant is required only a short time during the coldest days of the winter. Then the excess capacity during the milder days can be used as heat source for drying of wood chips to be marketed. Then wood chips are sieved and the fuel with best quality is sold and the reject is used as fuel in the plant it self. In a larger district heating plant, quality of the fuel does not need to be so high In this paper the effect of moisture on the fuel chain and on the boiler is discussed. Energy and mass balance calculations as a tool of system design is described and the characteristics of proposed dry chips production method is discussed.

On the necessity of improving the environmental impacts of furniture and appliances in net-zero energy buildings.

Science.gov (United States)

Hoxha, Endrit; Jusselme, Thomas

2017-10-15

There is now clear evidence regarding the extensive use of furniture and appliances in daily human life, but there is less evidence of their impact on the environment. Responding to this gap in knowledge, this study focuses on an assessment of the environmental impacts of furniture and appliances as used in highly energy efficient buildings. Their primary energy, non-renewable energy and global warming potential indicators have been assessed by extending the boundaries of the Life Cycle Assessment (LCA) study beyond the building itself. In conclusion, we found that furniture and appliances were responsible for around 30% of greenhouse gas emissions and non-renewable energy consumption and 15% of primary energy consumption comparing to the overall impacts of the building. Since embodied impacts represent the largest values, the process for labelling the appliances' energy efficiency should encompass a life-cycle point of view, not just a usage point of view as the case currently. Among office appliances, computer equipment was ranked as the highest impacting element, especially laptops and monitors. As for domestic appliances, refrigerators and electric ovens had the biggest impacts. Concerning furniture, the greatest impacts were from office and kitchen cabinets. Copyright © 2017 Elsevier B.V. All rights reserved.

Territorialisation et enclaves littorales dans les îles de la Caraïbe

Directory of Open Access Journals (Sweden)

Michel Desse

2008-04-01

Full Text Available Les littoraux de la Caraïbe ont longtemps été considérés comme des espaces de l’envers, ouverts, libres, propriété de l’Etat donc de tous, opposables à la plantation qui hiérarchise la société, structure le paysage et identifie la richesse.Aujourd’hui, les littoraux constituent les centres fonctionnels des îles, annexés parfois privatisés, ils apparaissent fortement territorialisés. Les facteurs qui expliquent ces transformations sont multiples. Les îles connaissent une forte tertiairisation ...

1992-1993 Bonneville Appliance Efficiency Program: Showerhead evaluation. Volume I - report

Energy Technology Data Exchange (ETDEWEB)

Warwick, W.M.

1995-01-01

The Bonneville Power Administration (Bonneville) provides wholesale electric power to over 100 retail distribution utilities in the Pacific Northwest. Bonneville is faced with meeting growing loads from these utilities. It acquires conservation as one means of meeting this load growth. Bonneville has offered a variety of conservation programs since 1980. Efficient showerheads have been a feature in residential conservation programs ever since. Bonneville launched the Residential Appliance Efficiency Program to focus on water-heater energy conservation opportunities in 1992. The Residential Appliance Efficiency Program consists of two parts, a water-heater efficiency program, and a hot-water efficiency program. This report evaluates the savings and costs of the first two years of the showerhead portion of the Residential Appliance Efficiency Program (the showerhead program). Although it is not a formal evaluation of the program limited to implementation or a {open_quotes}process{close_quotes} evaluation, observations about program design and implementation are included as appropriate. Results of this evaluation are limited to program participants within the Bonneville service territory.

Vertical growth control during maxillary expansion using a bonded Hyrax appliance

Directory of Open Access Journals (Sweden)

Francisco Marcelo Paranhos Pinto

2012-02-01

Full Text Available INTRODUCTION: Rapid maxillary expansion (RME for the treatment of maxillary deficiency and posterior crossbite may induce changes in the vertical dimension. Expanders with occlusal splints have been developed to minimize unwanted vertical effects. OBJECTIVE: This preliminary study used cephalometri radiographs to evaluate the vertical effects of RME using a Hyrax appliance in children with maxillary deficiency. METHOD: Twenty-six patients (11 boys; mean age = 8 years and 5 months with maxillary deficiency and posterior crossbite were treated using a Hyrax appliance with an acrylic occlusal splint. Radiographs and cephalometric studies were performed before the beginning of the treatment (T1 and after RME active time (T2, at a mean interval of 7 months. Results were compared with normative values. RESULTS AND CONCLUSIONS: At the end of treatment, there were no statistically significant changes, and measurements were similar to the normative values. Data showed that there were no significant effects on vertical growth, which suggests that appliances with occlusal splints may be used to correct transverse deficiencies regardless of the patient's growth pattern.

Les pressions écologiques réglementaires : comment les entreprises tunisiennes les gèrent-elles ?

Directory of Open Access Journals (Sweden)

Ahmed Turki

2012-06-01

Full Text Available Les entreprises sont de plus en plus appelées aujourd’hui à prendre en considération les aspects environnementaux dans leur gestion. Elles sont la cible des pressions environnementales dont la principale source est les pouvoirs publics. Ainsi, le présent papier se propose d’étudier la nature de la relation entre les entreprises et les pouvoirs publics en matière de protection de l’environnement. Afin d’atteindre cet objectif, une étude de cas est effectuée sur 8 entreprises tunisiennes dont deux sont certifiées par la norme ISO 14001. Les résultats montrent que toutes les entreprises ont fait l’objet d’inspections périodiques et de pénalités de la part des pouvoirs publics qui constituent la principale et parfois l’unique source de pression environnementale dans le contexte tunisien. Ces entreprises trouvent que les normes législatives environnementales sont difficiles à atteindre. Aussi, les résultats identifient deux types de relations entre les entreprises et les pouvoirs publics : coopérative et conflictuelle. De même, l’étude de cas montre que les pressions environnementales ont diminué suite aux actions environnementales effectuées mais demeurent toujours présentes.Companies are today more and more called to consider the ecological aspects in their management. They are the target of the ecological pressures the main source of which is public authorities. So, the present paper suggests studying the nature of the relation between companies and public authorities in environmental protection. To reach this objective, a case study is made on 8 Tunisian companies among which two are certified to the standard ISO 14001. The results show that public authorities (constitute the most and sometimes the only source of ecological pressure in the Tunisian context. These pressures show themselves by overhauls and penalties. These companies find that the environmental legislative standards are difficult to achieve

N° 341-Diagnostic et prise en charge de la torsion annexielle chez les filles, les adolescentes et les femmes adultes.

Science.gov (United States)

Kives, Sari; Gascon, Suzy; Dubuc, Élise; Van Eyk, Nancy

2017-02-01

Passer en revue les connaissances scientifiques actuelles et formuler des recommandations relatives au diagnostic et à la prise en charge de la torsion annexielle chez les filles, les adolescentes et les femmes adultes. L'étude porte sur les facteurs de risque, la précision diagnostique, les options de prise en charge et les issues de la torsion annexielle. RéSULTATS: Nous avons examiné les études publiées en faisant des recherches dans MEDLINE, Embase, CINAHL et la Bibliothèque Cochrane à l'aide d'une terminologie contrôlée et de mots-clés appropriés (« adnexal torsion », « ovarian torsion »). Nous avons limité les résultats aux revues systématiques, aux essais contrôlés aléatoires, aux essais cliniques contrôlés et aux études d'observation. Nous avons refait les recherches de façon régulière et intégré de nouvelles données à la directive jusqu'en décembre 2014. Nous avons également étudié la littérature grise (non publiée) trouvée sur les sites Web d'organismes d'évaluation des technologies de la santé et d'autres organismes connexes, dans des collections de directives cliniques et dans des registres d'essais cliniques, et obtenue auprès d'associations nationales et internationales de médecins spécialistes. Les résultats ont été examinés et évalués par le comité CANPAGO de la Société des obstétriciens et gynécologues du Canada (SOGC), sous la direction des auteures principales. Les recommandations ont été classées selon les critères établis par le Groupe d'étude canadien sur les soins de santé préventifs. AVANTAGES, DéSAVANTAGES ET COûTS: L'application de la directive devrait aider les praticiens à adopter une approche de diagnostic et de prise en charge optimale en matière de torsion annexielle, à réduire au minimum les effets néfastes et à améliorer l'issue qui attend les patientes. La présente directive a été évaluée et approuvée par le Comité de pratique - gynécologie de la SOGC

Les trous noirs

CERN Document Server

Ioli, Elena

2016-01-01

L'univers est peuplé par des étoiles, des planètes, des galaxies, des astéroïdes, des comètes, mais les trous noirs en sont certainement les habitants les plus mystérieux et les plus fascinants ! Grâce à cette merveilleuse histoire racontée par papy Gino, professeur d'astronomie, les trous noirs n auront plus de secrets pour vous ! C est l'été, le soleil illumine le ciel, la plage est en feu : une journée à la plage pleine de jeux et de plongée qui va se transformer pour Bernardo, Gregorio et leurs deux amis en une aventure inattendue. Ils découvriront les secrets des trous noirs, d étranges objets célestes que personne n'a jamais vus mais qui existent bel et bien ! Grand-père Gino, un professeur d astronomie à la retraite, emmènera les enfants à l'intérieur d'un trou noir, leur expliquera pourquoi ils sont noirs, comment ils sont nés et comment les scientifiques pensent qu'ils vont mourir. Et Gino leur racontera même ce qui se trouve de l'autre côté d'un trou noir...

Stability of Class II fixed functional appliance therapy—a systematic review and meta-analysis

Science.gov (United States)

von Bremen, Julia; Ruf, Sabine

2016-01-01

Summary Objectives: To systematically search for scientific evidence concerning the stability of treatment (Tx) results achieved by means of Class II fixed functional appliance therapy and to assess possible differences between appliances. Search Methods: An electronic search of databases and orthodontic journals was carried out (until December 2013), with supplemental hand searching. In addition to the names of all identified appliances, the term fixed functional was used in combination with each of the following search terms: long-term, post-Tx, relapse, retention, stability. Selection Criteria: To be included in the review, the articles had to contain clear data on: Class II Tx with a fixed functional appliance (>5 patients), post-Tx period ≥ 1 year, assessment of ANB angle, Wits appraisal, molar relationship, soft-tissue profile convexity excluding the nose, overjet and/or overbite. Data Collection and Analysis: The literature search revealed 20 scientific investigations which corresponded to only two of the 76 identified appliances (Herbst and Twin Force Bite Corrector). As only one publication was found for the Twin Force Bite Corrector, a meta-analysis could only be performed for Herbst Tx. The data were extracted, pooled and weighted according to the number of patients in each study. Results: The mean values for post-Tx relapse (percentages relative to the Tx changes) were: ANB angle 0.2 degrees (12.4 per cent), Wits appraisal 0.5mm (19.5 per cent), sagittal molar relationship 1.2mm/0.1 cusp widths (21.8 per cent /6.5 per cent); soft-tissue profile convexity excluding nose less than 0.1 degrees (1.0 per cent), overjet 1.8mm (26.2 per cent), overbite Class II:1 1.4mm (44.7 per cent), overbite Class II:2 1.0mm (22.2 per cent). Conclusions: The scientific evidence concerning the stability of Tx results is inexistent for most fixed functional appliances for Class II correction except for Herbst appliance Tx. Even if the evidence level of most included studies

Educational Electrical Appliance Power Meter and Logger

Science.gov (United States)

Nunn, John

2013-01-01

The principles behind two different designs of inductive power meter are presented. They both make use of the microphone input of a computer which, together with a custom-written program, can record the instantaneous power of a domestic electrical appliance. The device can be built quickly and can be calibrated with reference to a known power…

Effect of material variation on the biomechanical behaviour of orthodontic fixed appliances: a finite element analysis.

Science.gov (United States)

Papageorgiou, Spyridon N; Keilig, Ludger; Hasan, Istabrak; Jäger, Andreas; Bourauel, Christoph

2016-06-01

Biomechanical analysis of orthodontic tooth movement is complex, as many different tissues and appliance components are involved. The aim of this finite element study was to assess the relative effect of material alteration of the various components of the orthodontic appliance on the biomechanical behaviour of tooth movement. A three-dimensional finite element solid model was constructed. The model consisted of a canine, a first, and a second premolar, including the surrounding tooth-supporting structures and fixed appliances. The materials of the orthodontic appliances were alternated between: (1) composite resin or resin-modified glass ionomer cement for the adhesive, (2) steel, titanium, ceramic, or plastic for the bracket, and (3) β-titanium or steel for the wire. After vertical activation of the first premolar by 0.5mm in occlusal direction, stress and strain calculations were performed at the periodontal ligament and the orthodontic appliance. The finite element analysis indicated that strains developed at the periodontal ligament were mainly influenced by the orthodontic wire (up to +63 per cent), followed by the bracket (up to +44 per cent) and the adhesive (up to +4 per cent). As far as developed stresses at the orthodontic appliance are concerned, wire material had the greatest influence (up to +155 per cent), followed by bracket material (up to +148 per cent) and adhesive material (up to +8 per cent). The results of this in silico study need to be validated by in vivo studies before they can be extrapolated to clinical practice. According to the results of this finite element study, all components of the orthodontic fixed appliance, including wire, bracket, and adhesive, seem to influence, to some extent, the biomechanics of tooth movement. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Evaluation of dentoskeletal effects of Farmand functional appliance (Fa II on class II malocclusion

Directory of Open Access Journals (Sweden)

Yassaei S.

2007-07-01

Full Text Available Background and Aim: Functional appliances refer to a variety of removable or fixed appliances designed to alter the mandibular position both sagitally and vertically, resulting in orthodontic and orthopedic changes. Despite the long history of functional appliances, there is still much controversy related to their effectiveness and mode of action. The aim of this study was to evaluate dental and skeletal effects of Fa II in patients with class II malocclusion due to mandibular deficiency.Materials and Methods: In this before-after clinical trial, 35 patients with class II div I malocclusion were selected. These samples were under treatment with Fa II appliance for 11 months. The range of age of females was 10-13 years and males 11-14 years. Combination analysis was used to determine skeletal and dental effects. Paired t-test was used to compare the differences of mean value pre and post treatment. P<0.05 was considered as the level of significance. Results: There was significant difference between pre and post treatment in respect to posterior and anterior facial height, eruption of upper and lower posterior teeth, eruption of upper anterior teeth, mandibular body length, ANB angle, IMPA and 1 to SN. No significant difference was observed between pre and post treatment regarding facial growth.Conclusion: Treatment with Fa II functional appliance leads to significant alterations in dental and skeletal elements of craniofacial complex and improvement of dental and jaws relationship.

The influence of different types of fixed orthodontic appliance on the growth and adherence of microorganisms (in vitro study).

Science.gov (United States)

Saloom, Hayder F; Mohammed-Salih, Harraa S; Rasheed, Shaymaa F

2013-02-01

Orthodontic appliances serve as different impact zones and modify microbial adherence and colonization, acting as foreign reserves and possible sources of infection. This study was conducted to investigate the effect of different types of fixed orthodontic appliances on the growth and adherence of microorganisms in oral flora which are Streptococcus mutans (S. mutans) and Candida albicans. Sixty-four of four different fixed orthodontic appliance-samples were used, divided into four groups of sixteen. Type I: Sapphire brackets- Coated wires, type II: Sapphire brackets- Stainless steel wires, type III: Stainless steel brackets- Coated wires and type IV: Stainless steel brackets- Stainless steel wires. Oral strains of S. mutans and Candida albicans were studied in the present study using biochemical test then microbial suspensions were prepared to do the tests of each microorganism including the antimicrobial effects of different appliance-samples on the growth of microorganisms and their adhesion tests. The results showed significant differences between the different appliances in terms of inhibition zone formation (PAppliance with high esthetic appearance, sapphire brackets and coated arch wire, showed the least adherence of S. mutans and Candida albicans in comparison to other appliances with less esthetic and more metal components. Key words:Orthodontic appliance, Adherence, Streptococcus mutans, Candida albicans.

Short-term changes in chewing efficiency and subjective evaluation in normal dentate subjects after insertion of oral appliances with an occlusal flat table.

Science.gov (United States)

Satokawa, Y; Minami, I; Wakabayashi, N

2018-02-01

Oral appliances with an occlusal flat table are used as treatment dentures. However, the short-term effect of insertion of such oral appliances on chewing has not been reported. This study aimed to determine whether experimental and continuous insertion of oral appliances with an occlusal flat table has an effect on chewing efficiency and Oral Health Impact Profile (OHIP) in healthy participants. Ten participants each in the oral-appliance and control (no oral-appliance insertion) groups attended six data collection sessions for 5 consecutive days. Participants answered the OHIP questionnaire and underwent the chewing efficiency test. For each parameter, intergroup differences were investigated in terms of change from baseline to immediately after oral-appliance insertion (0 hour; P appliance insertion (P appliance insertion (P = .477 and .275, respectively). Differences between the two groups in the degree of change in other parameters were not significant. Insertion of oral appliances caused a decrease in chewing efficiency and an increase in OHIP scores. Continuous insertion improved functional limitation and physical pain within 96 hours. © 2017 John Wiley & Sons Ltd.

Boundedly rational consumers, energy and investment literacy, and the display of information on household appliances

NARCIS (Netherlands)

Blasch, J.E.; Filippini, Massimo; Kumar, Nilkanth

2017-01-01

It is an ongoing debate how to increase the adoption of energy-efficient light bulbs and household appliances in the presence of the so-called ‘energy efficiency gap’. One measure to support consumers’ decision-making towards the purchase of more efficient appliances is the display of energy-related

Treatment timing for functional jaw orthopaedics followed by fixed appliances: a controlled long-term study.

Science.gov (United States)

Pavoni, Chiara; Lombardo, Elisabetta Cretella; Lione, Roberta; Faltin, Kurt; McNamara, James A; Cozza, Paola; Franchi, Lorenzo

2017-11-01

To evaluate the role of treatment timing on long-term dentoskeletal effects of Class II treatment with removable functional appliances followed by full-fixed appliance therapy. A group of 46 patients (23 females and 23 males) with Class II malocclusion treated consecutively with either Bionator or Activator, followed by fixed appliances was compared with a matched control group of 31 subjects (16 females and 15 males) with untreated Class II malocclusion. The treated sample was evaluated at T1, start of treatment (mean age: 9.9 ± 1.3 years); T2, end of functional treatment and prior to fixed appliances (mean age: 11.9 ± 1.3 years); and T3, long-term observation (mean age: 18.3 ± 2.1 years). The treated and the control samples were divided into pre-pubertal and pubertal groups according to skeletal maturity observed at the start of treatment. Statistical comparisons were performed with independent sample t-tests. When treatment was initiated before puberty, Class II correction was mostly confined to the dentoalveolar changes, with significant improvements of both overjet and molar relationships. On the other hand, treatment with the outset at puberty produced significant long-term improvement of sagittal skeletal relationships, which were mainly sustained by mandibular changes. Treatment with removable functional appliances (Bionator or Activator) followed by full-fixed appliances produced significant skeletal long-term changes when it begins at puberty. Prepubertal Class II treatment results primarily in dentoalveolar changes. © The Author 2017. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

Les bourses du CRDI appuient les futurs chefs de file dans le ...

International Development Research Centre (IDRC) Digital Library (Canada)

13 mai 2015 ... Un programme de bourses de recherche du CRDI appuie les recherches novatrices et renforce le leadership futur et les connaissances sur les TIC, les ... Internet, la radio communautaire et la vidéo participative, présentent un fort potentiel pour faire face aux répercussions des changements climatiques et ...

High-Resolution Gas Metering and Nonintrusive Appliance Load Monitoring System

Science.gov (United States)

Tewolde, Mahder

This thesis deals with design and implementation of a high-resolution metering system for residential natural gas meters. Detailed experimental measurements are performed on the meter to characterize and understand its measurement properties. Results from these experiments are used to develop a simple, fast and accurate technique to non-intrusively monitor the gas consumption of individual appliances in homes by resolving small amounts of gas usage. The technique is applied on an existing meter retrofitted with a module that includes a high-resolution encoder to collect gas flow data and a microprocessor to analyze and identify appliance load profiles. This approach provides a number of appealing features including low cost, easy installation and integration with automated meter reading (AMR) systems. The application of this method to residential gas meters currently deployed is also given. This is done by performing a load simulation on realistic gas loads with the aim of identifying the necessary parameters that minimize the cost and complexity of the mechanical encoder module. The primary benefits of the system are efficiency analysis, appliance health monitoring and real-time customer feedback of gas usage. Additional benefits of include the ability to detect very small leaks and theft. This system has the potential for wide scale market adoption.

Inegalites entre les garçons et les filles dans l'evaluation en ...

African Journals Online (AJOL)

Cette recherche se propose d'étudier les inégalités entre les garçons et les filles dans l'évaluation en Education Physique et Sportive dans les collèges et surtout de connaître leurs sentiments par vis-à-vis de cette évaluation. Cette étude aura pour cadre les établissements secondaires de Porto-Novo et environs.

Estimation of Operating Condition of Appliances Using Circuit Current Data on Electric Distribution Boards

Science.gov (United States)

Iwafune, Yumiko; Ogimoto, Kazuhiko; Yagita, Yoshie

The Energy management systems (EMS) on demand sides are expected as a method to enhance the capability of supply and demand balancing of a power system under the anticipated penetration of renewable energy generation such as Photovoltaics (PV). Elucidation of energy consumption structure in a building is one of important elements for realization of EMS and contributes to the extraction of potential energy saving. In this paper, we propose the estimation method of operating condition of household appliances using circuit current data on an electric distribution board. Circuit current data are broken down by their shape using a self-organization map method and aggregated by appliance based on customers' information of appliance possessed. Proposed method is verified using residential energy consumption measurement survey data.

Les Fintech sont-elles une opportunité ou une menace pour les banques traditionnelles ?

OpenAIRE

Blanc, Aldwin; Sonney, Frédéric

2018-01-01

Dans ce travail, nous étudierons les potentielles opportunités et menaces que sont les Fintech pour les institutions bancaires. Cela nous permettra de savoir si, à l’avenir, ces entreprises vont s’imposer et remplacer les banques telles que nous les connaissons ou alors aider, forcer les acteurs traditionnels à effectuer leur révolution numérique pour répondre aux nouvelles attentes des clients. Afin de répondre à cette interrogation, les trois strates de l’environnement bancaire ont été anal...

Autres modèles de prestation de services publics dans les ...

International Development Research Centre (IDRC) Digital Library (Canada)

Les écrits sur la prestation de services publics à l'aide de modèles différents ont porté jusqu'à maintenant sur des endroits très précis. Ils ont par ailleurs été circonscrits à des secteurs donnés et ont manqué d'uniformité sur le plan méthodologique. Ce projet vise à analyser les modèles de prestation de services de santé, ...

Cost-effectiveness of high-efficiency appliances in the U.S. residential sector: A case study

International Nuclear Information System (INIS)

McNeil, Michael A.; Bojda, Nicholas

2012-01-01

This paper presents an analysis of the cost-effectiveness of high-efficiency appliances in the U.S. residential sector using cost and efficiency data developed as part of the regulatory process of the U.S. Department of Energy's Appliances and Commercial Equipment Standards Program. These data are presented as a case study in the development of an ‘efficiency technology database’ which can be expanded and published as a resource to other researchers and policy makers seeking scenarios that optimize efficiency policies and forecast their likely impacts on energy demand and greenhouse gas emissions. The use of this data to evaluate cost-effectiveness according to a variety of metrics is demonstrated using the example of one refrigerator–freezer product class. Cost-effectiveness is then evaluated in terms of cost of conserved energy for refrigerators, room air conditioners, water heaters, cooking equipment, central air conditioners and gas furnaces. The resulting potential of cost-effective improvement ranges from 1% to 53% of energy savings, with a typical potential of 15–20%. - Highlights: ► We determined the potential for cost-effective efficiency for residential appliances. ► We cover 6 appliance groups using cost of conserved energy as a metric for cost-effectiveness. ► Data are source from the DOE's Appliance and Commercial Equipment Standards Program. ► Between 15% and 20% additional cost-effective efficiency improvement is possible.

Measuring equipment and regulation of gas consuming appliances. Requirements for measuring equipments and regulation of gas consuming appliances; Maeleudstyr og indregulering af gasforbrugende apparater. Krav til maeleudstyr og indregulering af gasforbrugende apparater. Projektrapport

Energy Technology Data Exchange (ETDEWEB)

Andersen, H.

2004-06-01

Regulation of gas consuming appliances has so far been regarded as a banality. However, during recent years a number of misunderstandings have arisen in this area. The load to which a gas consuming appliance should be regulated under practical conditions is often unclear. By way of example may be mentioned that the factory typically set the load using G20 reference gas (pure methane). Under practical Danish conditions the load (with Danish natural gas) is approx. 2% higher than the load set from the factory. This report focuses on the problems with varying gas composition in relation to regulation of gas consuming appliances. Furthermore, a number of unclear points concerning measuring equipment are dealt with. The report aims at offering suggestions for practical solutions. (BA)

78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2013-09-04

... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

A long-term controlled follow-up study of objective treatment need on young adults treated with functional appliances.

Science.gov (United States)

Faxén Sepanian, Varoojan; Paulsson-Björnsson, Liselotte; Kjellberg, Heidrun

2014-01-01

The aims of this study were to 1) evaluate the objective success rate of Class II malocclusion treatment with functional appliances five years after completion of treatment and 2) to compare the remaining objective treatment need with an untreated control group. Records of all listed patients between 18-20 years (n=1054) treated in a general practice were reviewed for the purpose of finding treatments with removable functional appliances. Among all subjects (n=61) who previously had been treated, 58 accepted to participate in the study.The test group was matched with an orthodontically untreated group with no history of objective treatment need. Clinical examination was performed and study casts and photos were taken from both groups.The objective treatment need was evaluated through clinical examination and study cast analysis with weighted Peer Assessment Rating index (wPAR). Twenty patients, (34.5%) (mean wPAR 13.8), succeeded with the functional appliance treatment.The wPAR score (mean 15.0) of the entire test group was significantly higher than the one of the control group (mean 7.3).The group that was treated exclusively with functional appliances had a mean wPAR score of 17.4. Eighteen patients (31.0%) who received retreatment with fixed appliances had a slightly higher mean wPAR (8.6) than the control group. Treatments with functional appliances in a general practice showed a high failure rate and a remaining treatment need. It is the treating dentist's responsibility to motivate the patient to cooperate to the treatment, because as it previously has been shown the treatment with functional appliances is a well-functioning treatment alternative with the cooperation of the patient being sufficient. It is also of importance, already before starting treatment, to estimate the child's cooperation ability and to avoid treatment with removable appliances if the child or parents are reluctant about such a treatment.

Evaluation of RANS and LES models for Natural Convection in High-Aspect-Ratio Parallel Plate Channels

Science.gov (United States)

Fradeneck, Austen; Kimber, Mark

2017-11-01

The present study evaluates the effectiveness of current RANS and LES models in simulating natural convection in high-aspect ratio parallel plate channels. The geometry under consideration is based on a simplification of the coolant and bypass channels in the very high-temperature gas reactor (VHTR). Two thermal conditions are considered, asymmetric and symmetric wall heating with an applied heat flux to match Rayleigh numbers experienced in the VHTR during a loss of flow accident (LOFA). RANS models are compared to analogous high-fidelity LES simulations. Preliminary results demonstrate the efficacy of the low-Reynolds number k- ɛ formulations and their enhancement to the standard form and Reynolds stress transport model in terms of calculating the turbulence production due to buoyancy and overall mean flow variables.

Removable orthodontic appliance with nickel-titanium spring to reposition the upper incisors in an autistic patient.

Science.gov (United States)

Saito, Kan; Jang, Insan; Kubota, Kazumi; Hoshino, Tomonori; Hotokezaka, Hitoshi; Yoshida, Noriaki; Fujiwara, Taku

2013-01-01

A newly designed removable appliance with a shape-memory wire was used for the orthodontic treatment of the anterior teeth in an 11-year-old child who had autism and intellectual disability. The device was designed to reduce the lateral incisor crossbite and the central incisors' labial rotation. The child was treated for 1 year with this removable appliance. Tooth movement was analyzed using cephalograms and surface data were derived from study models. This device proved to be very durable. The lateral incisor crossbite was corrected, and the inclination of the upper central incisors and the interincisal angle were improved. This appliance exerts light and continuous orthodontic force, without requiring any adjustments of the spring wire. The appliance also facilitated orthodontic treatment in a child with intellectual disability in whom treatment with a standard orthodontic device would be unsuitable. ©2012 Special Care Dentistry Association and Wiley Periodicals, Inc.

46 CFR 199.176 - Markings on lifesaving appliances.

Science.gov (United States)

2010-10-01

... ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Requirements for All Vessels § 199.176 Markings on lifesaving appliances. (a) Lifeboats and rescue boats. Each lifeboat and rescue boat must be plainly marked as follows: (1) Each side of each lifeboat and rescue boat bow must be marked in block...

Les adjectifs à valeur intensive dans les groupes nominaux

Directory of Open Access Journals (Sweden)

Buvet Pierre-André

2012-07-01

Full Text Available Un dictionnaire électronique est élaboré dans la perspective du Traitement Automatique des Langues. Il s'agit d'une ressource qui est exploité par un ensemble d'outils informatiques pour donner lieu à une application dédiée au traitement de l'information textuelle. Le dictionnaire électronique présenté dans l'article concerne principalement des adjectifs prédicatifs à forme simple qui ont fait l’objet d’un recensement exhaustif et qui ont été décrits formellement. Sa macrostructure est constituée de plus de 20 000 emplois adjectivaux. Sa microstructure comporte des descripteurs normalisés de telle sorte que les informations métalinguistiques stipulées permettent d'effectuer des analyses sémantiques fines. Les adjectifs prédicatifs à forme complexe sont également incorporés au dictionnaire; ils sont décrits comme les adjectifs prédicatifs à forme simple dans la mesure où ils fonctionnent de la même façon. Dans un premier temps, nous discutons de la notion d'adjectif prédicatif en précisant préalablement les notions de prédicat et d'emploi prédicatif ainsi que celles de signification lexicale et de signification grammaticale. Nous présentons les marqueurs de l’intensité qui correspondent à des adjectifs monolexicaux et prédicatifs ou bien polylexicaux et prédicatifs. Nous discutons de ces adjectifs dans un premier temps selon qu’il s’agit de modifieurs libres, dans un deuxième temps de modifieurs liés et dans un troisième temps de constituants d’une détermination figée. Nous précisons dans les trois cas de figure quelles sont les conditions d’occurrences des adjectifs prédicatifs dans les groupes nominaux en nous appuyant sur les descriptions des adjectifs et des déterminants du français qui proviennent de deux bases de données exhaustives.

Pre-directional appliance: A new approach to correct shifted premaxilla in bilateral cleft cases

Directory of Open Access Journals (Sweden)

P S Daigavane

2011-01-01

Full Text Available Management of bilateral cleft lip and palate cases is a challenging task, and if the premaxilla is shifted to either side, it poses a problem for the surgeon to operate and also for the orthodontist to do the orthodontic alignment. The aim of this study was to reposition the shifted premaxilla for better retraction with presurgical infant orthopedics, thus reducing the tissue tension and further scarring which have detrimental effects on maxillary growth. The innovative technique with pre-directional (PD appliance is easy to fabricate and use and works in this direction. Acrylic, springs, permasoft liner, elastics, retentive tapes. Previous approach for the shifted premaxilla was more focused on the surgical correction. In adults, surgery with osteotomy is the only option, with its own limitations and disadvantages, in repositioning the shifted premaxilla. Thus, PD appliance aids to correct the shifted premaxilla in presurgical molding stage. The premaxilla was thus shifted 5.5 mm to the left side, with premaxilla in facial symmetry, with the PD appliance. Presurgical orthopedics with PD appliance is worth in infants with shifted premaxilla in bilateral clefts cases.

Effects of the Herbst appliance in growing orthodontic patients with different underlying vertical patterns.

Science.gov (United States)

Deen, Emily; Woods, Michael G

2015-05-01

The present study involved an assessment of the effects of the Herbst appliance used for Class II correction in subjects with different vertical facial patterns. Pre- and post-treatment lateral cephalograms of 91 growing Class II patients were divided into three vertical facial groups on the basis of mandibular plane angulation. All received a Herbst appliance and dental and skeletal changes were assessed in relation to pretreatment incisal overbite, overjet and the stage of cervical maturity. Herbst appliance treatment was accompanied by changes in the angulation of the upper and lower incisors, overjet reduction and an increase in mandibular length. In general, the rotational facial changes occurring during treatment were minimal, so that dolichofacial patterns remained long and brachyfacial patterns remained short. Herbst appliance treatment can be expected to result in considerable Class II dental correction. It is unlikely, however, that its use will be associated with clinically significant forward rotation in dolichofacial subjects. Since dolichofacial patterns are likely to remain long-faced, even after considerable Class II dental correction, orthognathic surgery may still be a consideration if normal facial proportions, without excessive facial convexity and lip strain, are treatment aims.

Evaluation of safety management in an Appliances manufacturing company

Directory of Open Access Journals (Sweden)

F. Golbabaei

2015-01-01

Full Text Available Introduction: Prevention of accidents and work related diseases, are not allowed regardless of the safety of employees, customers, contractors and other persons. Assessment of individual safety management activities could reduce many losses. Present study aimed to evaluate the safety management of a household appliance manufacturing company.  .Material and Method: This study has done in a household appliance manufacturing company in Damavand city. Two questionnaires were firstly designed based on the weighted scores. The questionnaire 1 consisted of 4 indicators: Safety of machinery, Electrical safety, Risk assessment and Fire safety. Questionnaire 2 consisted of 11 sub indicators. Both questionnaires were completed by 30 HSE experts and supervisors. Reliability of questionnaires was based on cronbachs alpha coefficient. the safety status of each unit was determined and scored using information acquired by the questionnaires. Lastly, the safety of the entire company was determined.  .Result: Results showed that in safety management: the pressing and store house were in a good range of 66.66 and 60.12 points. Powder painting, enameling, laboratory were in a average range of 56.25, 55.92 and 54.15 points. Assembling and door storage were in a week range of 46.06 points.  .Conclusion: The findings showed that the safety status in the studied appliances company is in average range with 55.45 points. Therefore, it is recommended that the safety indicators should be improved for the betterment of the safety management in the company.

Experimental similitude determination of the influence of perturbations in the thickness of a heating channel on the isolated wall temperatures (1960); Determination experimentale en similitude de l'influence de perturbations dans l'epaisseur d'un canal chauffant sur les temperatures de la paroi isolee (1960)

Energy Technology Data Exchange (ETDEWEB)

Vernier, Ph [Commissariat a l' Energie Atomique, Grenoble (France).Centre d' Etudes Nucleaires; Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

A study is made of the local heating phenomena produced on the isolated wall of a channel heated by the Joule effect by a sudden fluctuation in the conducting thickness. By the use of an experimental scale model it has been possible to measure the differences in the isolated wall temperature along the abscissa of the perturbation. The tests carried out show that the temperature differences are contained within a range of {+-} 4 per cent with respect to the temperature differences between the isolated and the isolated walls. (author) [French] On analyse le phenomene thermique local cree sur la paroi isolee d'un canal chauffe par effet Joule, par une perturbation brusque de l'epaisseur conductrice. Un modele experimental a l'echelle a permis de mesurer les ecarts de temperature de la paroi isolee a l'abscisse de la perturbation. Les essais realises ont montre que les ecarts de temperature se situaient dans une bande de {+-} 4 pour cent par rapport a l'ecart de temperature moyen entre paroi isolee et paroi refroidie. (auteur)

Les lieux du sacré dans les Miracula sancti Germani d’Heiric d’Auxerre et les Gesta pontificum Autissiodorensium

Directory of Open Access Journals (Sweden)

Dominique Iogna-Prat

2004-09-01

Full Text Available Comment cerner la notion de sacré dans les textes carolingiens que sont les Gestes des évêques d’Auxerre et les Miracles de saint Germain écrits par l’un des maîtres de l’école carolingienne d’Auxerre, Heiric ? Une étude lexicale précise des mots latins employés par les auteurs permet d’approcher au plus près les concepts renvoyant aux lieux du sacré. Ce sujet de maîtrise. suggéré par D. Iogna-Prat et réalisé sous la direction de M. Bourin (université de Paris I-Panthéon Sorbonne, avec l’aid...

An experiment with spectral analysis of emotional speech affected by orthodontic appliances

Science.gov (United States)

Přibil, Jiří; Přibilová, Anna; Ďuračková, Daniela

2012-11-01

The contribution describes the effect of the fixed and removable orthodontic appliances on spectral properties of emotional speech. Spectral changes were analyzed and evaluated by spectrograms and mean Welch’s periodograms. This alternative approach to the standard listening test enables to obtain objective comparison based on statistical analysis by ANOVA and hypothesis tests. Obtained results of analysis performed on short sentences of a female speaker in four emotional states (joyous, sad, angry, and neutral) show that, first of all, the removable orthodontic appliance affects the spectrograms of produced speech.

77 FR 72324 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Countervailing...

Science.gov (United States)

2012-12-05

... Shelving and Racks from the People's Republic of China: Countervailing Duty Administrative Review, 2010... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China. See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

78 FR 28190 - Authorization of Production Activity; Foreign-Trade Subzone 29C; GE Appliances (Electric Water...

Science.gov (United States)

2013-05-14

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-7-2013] Authorization of Production Activity; Foreign-Trade Subzone 29C; GE Appliances (Electric Water Heaters); Louisville, Kentucky On January 7, 2013, GE Appliances, operator of Subzone 29C in Louisville, Kentucky, submitted a notification of proposed...

Clean energy, technical files; Energie propre, les fiches techniques

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

This document is the compilation of the 42 issues of the 'Energie propre - Maitrise de la Demande d'Energie' newsletter published between September 1996 and July 1999 by the regional energy agency of Provence-Alpes-Cote d'Azur region (ARENE). Each issue is a technical file presenting a particular action or study carried out in the framework of the program of mastery of energy demand in Provence-Alpes-Cote d'Azur region (SE France). These studies and actions concern various types of buildings: high schools, residential buildings for old people, office buildings, social buildings, hotels, recreational facilities, and cover all aspects of energy conservation: space heating, lighting systems, ventilation systems, thermal insulation, appliances.. (J.S.)

Occlusal bite force change after orthodontic treatment with Andresen functional appliance.

Science.gov (United States)

Al-Khateeb, Susan N; Abu Alhaija, Elham S; Majzoub, Sami

2015-04-01

The aim of this study was to determine the occlusal bite force (OBF) changes, at the incisal and molar regions, after orthodontic treatment with functional appliance therapy in preadolescent subjects. OBF was measured for patients (17 females and 16 males) before and after the treatment with Andresen functional appliance for an average period of 9 months (mean age was 11.8±1.1 years). Three variables were registered; maximum OBF at molar region and the average of three readings at the molar (AOBF) and incisal regions (IOBF). The same variables were measured in two occasions for a matching non-treated control group with a period of 9 months between the two measurements. No significant changes were seen in the OBF measured parameters in the control group. There was a reduction in all measured parameters. The mean reduction in maximum OBF was 76.1±12.4 N (P appliance caused a significant reduction in OBF immediately after treatment. © The Author 2014. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

The Hybrid Aesthetic Functional (HAF) Appliance: A Less Visible Proposal for Functional Orthodontics

Science.gov (United States)

2013-01-01

In modern orthodontics, aesthetics appear to have a decisive influence on orthodontic appliance preferences and acceptability. This paper reports the early application of a newly emerged functional device with enhanced aesthetics in a Class II treatment. Patient perspectives and technical considerations are discussed along with recommendations for further design development. It can be assumed that the use of thermoplastic material-based appliances may meet both the therapeutic and aesthetic demands of young age groups. PMID:23956884

Maxillary molar distalization or mandibular enhancement: a cephalometric comparison of comprehensive orthodontic treatment including the pendulum and the Herbst appliances.

Science.gov (United States)

Burkhardt, Donald R; McNamara, James A; Baccetti, Tiziano

2003-02-01

Several methods of Class II treatment that do not rely on significant patient compliance have become popular during the last decade, including several versions of the Herbst appliance and the pendulum or Pendex molar-distalization appliances. Yet, these 2 general approaches theoretically have opposite treatment effects, one presumably enhancing mandibular growth, and the other moving the maxillary teeth posteriorly. This study examined the treatment effects produced by 2 types of the Herbst appliance (acrylic splint and stainless-steel crown) followed by fixed appliances, and the pendulum appliance followed by fixed appliances. For each of the 3 treatment groups, lateral cephalograms were analyzed before the start of treatment (T1) and after the second phase of treatment (T2). Patients were matched according to age and sex. The comprehensive treatment time for the pendulum group was 31.6 months, and the acrylic and crowned Herbst groups were treated for 29.5 months and 28.0 months, respectively. Overall from T1 to T2, there were no statistically significant differences in mandibular growth among the 3 groups. Skeletal changes accounted for a larger portion of molar correction in the Herbst treatment groups than in the pendulum group. Patients in the pendulum group had an increase in the mandibular plane angle. Conversely, the mandibular plane angle in patients treated with either Herbst appliance closed slightly from T1 to T2. At T2, the chin points (pogonion) of patients in both Herbst groups, however, were located slightly more anteriorly than were the chin points of the pendulum patients. It is likely that the slight downward and backward rotation of the mandible occurring during treatment in the pendulum patients accounted for much of this difference. The treatment effects produced by the 2 types of Herbst appliance were similar at T2, in spite of their differences in design. It is important not to generalize the findings of this comparison beyond the appliance

Anterior crossbite correction with a series of clear removable appliances: a case report.

Science.gov (United States)

Park, Jae Hyun; Kim, Tae Weon

2009-01-01

The Clear Aligner can be used to correct tooth movement without involving extraction, surgery, and other adjunct orthopedic appliances. The Clear Aligner is a procedure that can be performed by either an orthodontist or a general dentist without computer simulation/calculation. Since the Clear Aligner is fabricated from the stone model for new appliance at each or every other appointment, it is readily available to change the treatment sequence throughout the course of the treatment. The patient can receive any necessary dental procedures with ease during the course of the treatment. The treatment can also be easily resumed even if the patient has not worn the aligners for a period of time. The purpose of this article is to report dental anterior crossbite correction with a series of Clear Aligners. The Clear Aligner could be used as an alternative in appropriate cases for those who are reluctant with conventional appliances.

CE APPROVAL IN ELECTRICAL HOUSEHOLD APPLIANCES AND A CASE STUDY

Directory of Open Access Journals (Sweden)

Nazmi EKREN

2009-01-01

Full Text Available Due to the reason for rapidly developing technology, increasing competition medium, and awareness of the consumers, nowadays, the exigency of production with good quality has gained more and more significance. Certification of the quality and safety of the products to the consumers is compulsory in terms of producers. There are some documents to certify safety of the products. One of them is CE certificate. In this paper, basic information about CE mark is given and CE standards and tests required for electrical household appliances are mentioned. As an application, one of an electrical household appliance, toaster grill is treated and examined. To obtain CE certificate for toaster grill, required tests are made according to EN60335-2-9 and CE certificate is obtained.

Les catastrophes naturelles présentent une menace pour les ...

African Journals Online (AJOL)

toufik

L'événement sismique a été simulé en utilisant le catalogue algérien des failles actives. Les résultats obtenus montrent que les constructions les plus endommagées sont celles qui reposent sur des sols meubles. Mots-clés : SIG, risque sismique, probabilité de dommages, courbes de fragilité, Hazus. Abstract. Use of a GIS ...

Correction of complete maxillary crossbite with severe crowding using Hyrax expansion and fixed appliance.

Science.gov (United States)

Wangsrimongkol, Tasanee; Manosudprasit, Montian; Pisek, Poonsak; Leelasinjaroen, Pornnapha

2013-09-01

An 18-year-old Thai man who presented with a secondary cleft palate, maxillary hypoplasia and severe crowding was treated by rapid maxillary expansion and fixed orthodontic appliances. Initial assessment found skeletal Class III malrelationship and dental Class II malocclusion with anterior and bilateral posterior crossbites. Camouflage orthodontic treatment was planned using a rapid maxillary expansion appliance and correcting crowding with extraction all four premolar teeth. A Hyrax appliance and vertical loop arch wire were placed for maxillary arch expansion of 9.5 mms at first molars and canines, and 5.5 mms at the premolars and obtained positive overjet. Both acceptable skeletal and soft tissue relationships and satisfactory occlusion were produced. After 14 months of postoperative follow-up, the occlusal result was stable and no skeletal reversals could be detected.

Development and evaluation of a new depressurization spillage test for residential gas-fired combustion appliances : final report

International Nuclear Information System (INIS)

Edwards, P.

2005-07-01

This paper presented a newly developed combustion depressurization spillage test for residential combustion appliances. The test uses carbon dioxide (CO 2 ) that is produced in the fuel combustion process as a tracer gas. The test accurately measures the amount of combustion spillage from residential combustion appliances and their venting systems when they operate at certain levels of depressurization. Seven commonly used gas-fired appliances were used to evaluate the new test as well as the appliances. These included 2 power-vented storage-tank water heaters, 1 mid-efficiency furnace, 2 high-efficiency condensing furnaces, and 2 direct-vent gas fireplaces. Tests were performed for each unit with the test room initially depressurized by 50 Pa compared with the pressure outside the room. If the combustion spillage exceeded 2 per cent, the test was repeated with the room depressurized by 20 Pa, and then by 5 Pa. Each appliance was operated for 5 minutes of burner operation during which time the burner fuel consumption, the concentration of CO 2 and the exhaust fan flow rate were monitored. Measurements were taken for 2 minutes following burner shut off. The amount of CO 2 that was released into the test room from the appliance and its venting system was determined from the measurements and then compared with the amount of CO 2 that would be produced by combustion of the fuel that was consumed during the test. The ratio of the 2 provided a direct measure of the combustion spillage of the appliance and its venting system. The study revealed that 3 products had undetectable levels of combustion spillage, 3 products had low, but measurable combustion spillage, and 1 product had significant combustion spillage. refs., tabs., figs

Periodontal pathogen levels in adolescents before, during, and after fixed orthodontic appliance therapy.

Science.gov (United States)

Thornberg, Michelle J; Riolo, Christopher S; Bayirli, Burcu; Riolo, Michael L; Van Tubergen, Elizabeth A; Kulbersh, Richard

2009-01-01

This purpose of this study was to document and investigate changes in periodontal pathogen levels before, during, and after orthodontic treatment in adolescents. DNA gene probe analysis was used to quantify the levels of 8 periodontal pathogens before, during, and after treatment with fixed orthodontic appliances in 190 concurrently treated adolescent orthodontic patients. The 8 pathogens examined were Actinobacillus actinomycetemcomitans (AA), Porphyromonas gingivalis (PG), Prevotella intermedia (PI), Tannerella forsythia (TF), Eikenella corrodens (EC), Fusobacterium nucleatum (FN), Treponema denticola (TD), and Campylobacter rectus (CR). Chi-square tests were used to determine whether the percentages of subjects with high counts significantly changed over time. Logistic regression analyses were also performed to derive the relative risk of higher counts of pathogenic bacteria with fixed appliances at the various time intervals studied. For 6 (PI, TF, EC, FN, TD, CR) of the 8 pathogens, the percentages of subjects with high pathogen counts increased significantly after 6 months of fixed appliance treatment, but these returned to pretreatment levels by 12 months of orthodontic treatment. No pathogen level was significantly higher after 12 months of orthodontic treatment, and orthodontic treatment was found to be significantly protective for half of the pathogens (EC, FN, TD, CR) posttreatment. Orthodontic treatment with fixed appliances does not increase the risk of high levels of these periodontal pathogens.

Insufficient evidence to confirm effectiveness of oral appliances in treatment of obstructive sleep apnoea syndrome in children.

Science.gov (United States)

Fox, Nigel A

2007-01-01

Searches were made using the Cochrane Central Register of Controlled Trials, Medline, Embase, Latin American and Caribbean Health Sciences Literature, Bibliografia Brasileira de Odontologia and SciELO (the Scientific Electronic Library Online). Studies chosen were randomised controlled trials (RCT) or quasi-RCT comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children of 15 years old or younger. Data were independently extracted by two review authors. Authors were contacted for additional information. Risk ratios with 95% confidence intervals were calculated for all important dichotomous outcomes. A total of 384 trials were identified, of which only one, reporting results from a total of 23 patients, was suitable for inclusion in the review. Data provided in the published report did not answer all the questions from this review, but did answer some: the results presented favour treatment. At present there is not sufficient evidence to state that oral appliances or functional orthopaedic appliances are effective in the treatment of obstructive sleep apnoea (OSA) syndrome in children. Oral appliances or functional orthopaedic appliances may be helpful in the treatment of children with craniofacial anomalies which are risk factors for apnoea.

Impact of orthodontic appliances on the quality of craniofacial anatomical magnetic resonance imaging and real-time speech imaging.

Science.gov (United States)

Wylezinska, Marzena; Pinkstone, Marie; Hay, Norman; Scott, Andrew D; Birch, Malcolm J; Miquel, Marc E

2015-12-01

The aim of this work was to investigate the effects of commonly used orthodontic appliances on the magnetic resonance (MR) image quality of the craniofacial region, with special interest in the soft palate and velopharyngeal wall using real-time speech imaging sequences and anatomical imaging of the temporomandibular joints (TMJ) and pituitaries. Common orthodontic appliances were studied on 1.5 T scanner using standard spin and gradient echo sequences (based on the American Society for Testing and Materials standard test method) and sequences previously applied for high-resolution anatomical and dynamic real-time imaging during speech. Images were evaluated for the presence and size of artefacts. Metallic orthodontic appliances had different effects on image quality. The most extensive individual effects were associated with the presence of stainless steel archwire, particularly if combined with stainless steel brackets and stainless steel molar bands. With those appliances, diagnostic quality of magnetic resonance imaging speech and palate images will be most likely severely degraded, or speech imaging and imaging of pituitaries and TMJ will be not possible. All non-metallic, non-metallic with Ni/Cr reinforcement or Ni/Ti alloys appliances were of little concern. The results in the study are only valid at 1.5 T and for the sequences and devices used and cannot necessarily be extrapolated to all sequences and devices. Furthermore, both geometry and size of some appliances are subject dependent, and consequently, the effects on the image quality can vary between subjects. Therefore, the results presented in this article should be treated as a guide when assessing the risks of image quality degradation rather than an absolute evaluation of possible artefacts. Appliances manufactured from stainless steel cause extensive artefacts, which may render image non-diagnostic. The presence and type of orthodontic appliances should be always included in the patient

A randomized controlled trial of self-perceived pain, discomfort, and impairment of jaw function in children undergoing orthodontic treatment with fixed or removable appliances.

Science.gov (United States)

Wiedel, Anna-Paulina; Bondemark, Lars

2016-03-01

To compare patients' perceptions of fixed and removable appliance therapy for correction of anterior crossbite in the mixed dentition, with special reference to perceived pain, discomfort, and impairment of jaw function. Sixty-two patients with anterior crossbite and functional shift were recruited consecutively and randomized for treatment with fixed appliances (brackets and archwires) or removable appliances (acrylic plates and protruding springs). A questionnaire, previously found to be valid and reliable, was used for evaluation at the following time points: before appliance insertion, on the evening of the day of insertion, every day/evening for 7 days after insertion, and at the first and second scheduled appointments (after 4 and 8 weeks, respectively). Pain and discomfort intensity were higher for the first 3 days for the fixed appliance. Pain and discomfort scores overall peaked on day 2. Adverse effects on school and leisure activities were reported more frequently in the removable than in the fixed appliance group. The fixed appliance group reported more difficulty eating different kinds of hard and soft food, while the removable appliance group experienced more speech difficulties. No significant intergroup difference was found for self-estimated disturbance of appearance between the appliances. The general levels of pain and discomfort were low to moderate in both groups. There were some statistically significant differences between the groups, but these were only minor and with minor clinical relevance. As both appliances were generally well accepted by the patients, either fixed or removable appliance therapy can be recommended.

77 FR 12811 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Partial...

Science.gov (United States)

2012-03-02

... Shelving and Racks From the People's Republic of China: Partial Rescission of Antidumping Duty... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... Appliance Shelving and Racks from the People's Republic of China, dated January 10, 2012; and Letter to the...

76 FR 62765 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2011-10-11

... Shelving and Racks From the People's Republic of China: Preliminary Results of the First Administrative... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... administrative review of certain kitchen appliance shelving and racks from the PRC for the period March 5, 2009...

Interoperability for smart appliances in the IoT world

NARCIS (Netherlands)

Daniele, L.; Solanki, M.; Hartog, F. den; Roes, J.

2016-01-01

Household appliances are set to become highly intelligent, smart and networked devices in the near future. Systematically deployed on the Internet of Things (IoT), they would be able to form complete energy consuming, producing, and managing ecosystems. Smart systems are technically very

Hoisting appliances and fuel handling equipment at nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-12-31

The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection. 36 refs. Translation. The original text is published under the same guide number. The guide is valid from 5 January 1987 and will be in force until further notice.

Prise en charge de l’infection gonococcique chez les adultes et les jeunes

Science.gov (United States)

Pogany, Lisa; Romanowski, Barbara; Robinson, Joan; Gale-Rowe, Margaret; Latham-Carmanico, Cathy; Weir, Christine; Wong, Tom

2015-01-01

Résumé Objectif Présenter des recommandations sur la prise en charge de l’infection gonococcique chez les adultes et les jeunes. Qualité des données Les recommandations thérapeutiques des lignes directrices canadiennes sur les infections transmissibles sexuellement reposent sur une recherche documentaire de même que sur des catégories de recommandations et des niveaux de qualité de données déterminés par au moins 2 évaluateurs. Les recommandations ont été revues par des pairs et sont en instance d’approbation par le groupe de travail d’experts. Message principal Les nouvelles recommandations portant sur la prise en charge de l’infection gonococcique chez les adultes et les jeunes préconisent les cultures à titre d’outil diagnostique lorsqu’elles sont pratiques, le traitement par antibiothérapie combinée (ceftriaxone associée à l’azithromycine) et le signalement sans délai de tous les cas dont le traitement a échoué aux autorités de santé publique. Conclusion Si elles sont suivies, ces nouvelles recommandations pourraient réduire l’échec thérapeutique, contribuer à une surveillance plus étroite des tendances à la résistance de Neisseria gonorrhoeae aux antibiotiques et contribuer à prévenir la transmission de gonorrhée résistante à plusieurs médicaments.

Faut-il brûler les dictionnaires ? Ou comment les ressources numériques ont révolutionné les recherches en morphologie

Directory of Open Access Journals (Sweden)

Namer Fiammetta

2012-07-01

Full Text Available Pour mener leurs études, les morphologues, et, singulièrement parmi eux, ceux qui traitent du lexique construit, sont pris entre deux tensions : utiliser les données issues des dictionnaires, réputées fiables parce que passées au travers du crible de l’institutionnalisation, ou se fonder sur des données authentiques, produites dans des situations écologiques. Bien qu’inspirant encore de la défiance, le Web devient alors la ressource par excellence. Les ressources numérisées telles que les archives de journaux ou les bases de données de textes littéraires constituent un moyen terme entre ces deux pratiques : elles permettent d’effectuer des recherches basées sur l’usage, tout en offrant la garantie d’une certaine tenue linguistique de la part des scripteurs, la plupart du temps identifiables. Dans cette communication, nous nous demanderons si les dictionnaires méritent la confiance que continuent de leur octroyer les morphologues ou, plus exactement, si une morphologie qui puise ses données dans les seuls dictionnaires peut encore avoir cours au 21e siècle. Pour engager cette discussion, nous commencerons par poser la question de l’existence, pour un lexème construit. Nous exposerons ensuite ce que constitue une morphologie basée sur l’usage, puis donnerons un aperçu des types de recherches que permettent de réaliser les ressources non dictionnairiques. La conclusion sera que, si les dictionnaires continuent d'avoir droit de cité dans la panoplie du morphologue, une morphologie uniquement basée sur les données qu'ils contiennent passerait outre de nombreuses recherches, plus fructueuses les unes que les autres.

Transient heat transfer in longitudinal fins of various profiles with ...

Indian Academy of Sciences (India)

Transient heat transfer through a longitudinal fin of various profiles is studied. The thermal conductivity and heat transfer coefficients are assumed to be temperature dependent. The resulting partial differential equation is highly nonlinear. Classical Lie point symmetry methods are employed and some reductions are ...

Energy Efficiency of Electrical Appliances - Effects of Instruments and Measures; Energieeffizienz bei Elektrogeraeten

Energy Technology Data Exchange (ETDEWEB)

Brunner, C.U.; Bush, E.; Gasser, S.; Lingenhel, S.; Nipkow, J.

2001-07-01

This comprehensive report for the Swiss Federal Office of Energy presents the results of an analysis made of the market for electrical appliances in Switzerland with the aim of understanding the instruments and measures needed to improve energy efficiency better. The paper reports on reviews made of previous studies that were made in Switzerland and Germany and on interviews made with important persons and institutions in this field. Eight basic findings are listed concerning market expansion, technical progress, user behaviour, efficiency, possibilities for intervention, market forces, efficient appliances as a niche market and the competence lacking in the energy-efficiency area. Twelve basic points to be considered in the implementation of an energy-efficiency strategy are discussed and a list of requirements to be fulfilled by politics is presented. The results of the analysis for various sectors and the recommendations made for an implementation organisation are presented in detail. The report is concluded with a extract from the data base on the energy consumption of electrical appliances.

Gradients socioéconomiques du risque cardiovasculaire chez les enfants et les adolescents canadiens

Directory of Open Access Journals (Sweden)

Y. Shi

2016-01-01

Full Text Available Introduction : Les maladies cardiovasculaires (MCV et leurs facteurs de risque présentent des gradients socioéconomiques clairs chez les adultes canadiens, mais présentent des ambiguïtés chez les enfants. L'objectif de cette étude est de vérifier l'existence ou non de gradients socioéconomiques dans les marqueurs physiologiques du risque de MCV chez les enfants et les adolescents canadiens. Méthodologie : À partir des données transversales combinées de l'Enquête canadienne sur les mesures de la santé 2007-2011, nous avons étudié, chez 2 149 enfants (6 à 11 ans et 2 073 adolescents (12 à 17 ans et selon le sexe, les marqueurs de risque cardiovasculaire suivants : excès de poids (y compris l'obésité, score de capacité aérobique (SCA, pression artérielle (PA, lipides sanguins (totaux, cholestérol LDL et HDL, triglycérides, métabolisme du glucose et protéine C réactive (CRP. Des analyses de régression logistique et de régression linéaire multidimensionnelles ont permis de dégager les tendances relatives au risque cardiovasculaire en fonction de la suffisance du revenu du ménage et du niveau de scolarité des parents, après ajustement en fonction de l'âge et de l'origine ethnique, et après stratification par groupe d'âge et par sexe. Résultats : La prévalence de l'obésité était sensiblement plus élevée chez les jeunes garçons que chez les jeunes filles (prévalence de 18,5 %, intervalle de confiance [IC] à 95 % : 15,6 à 21,5 contre 7,7 %, IC à 95 % : 5,2 à 10,3. Toutefois, des gradients socioéconomiques négatifs ont été observés en ce qui concerne le risque d'adiposité chez les jeunes filles et les adolescentes, et non chez les garçons. Parmi les enfants et les adolescents, les garçons étaient en meilleure condition physique que les filles (SCA moyen de 541, IC à 95 % : 534 à 546 contre 501, IC à 95 % : 498 à 505 chez les enfants; 522, IC à 95 % : 514 à 529 contre 460, IC à 95 % : 454

Appliances facilitating everyday life - electricity use derived from daily activities

Energy Technology Data Exchange (ETDEWEB)

Ellegaard, Kajsa (Dept of Thematic Studies, Linkoeping Univ. (Sweden)), e-mail: kajsa.ellegard@liu.se; Widen, Joakim (Dept of Engineering Sciences, Uppsala Univ. (Sweden)); Vrotsou, Katerina (Dept of Science and Technology, Linkoeping Univ. (Sweden))

2011-06-15

The purpose of this paper is to present how, using a visualization method, electricity use can be derived from the everyday activity patterns of household members. Target groups are, on the one hand, professionals in the energy sector and energy advisors who need more knowledge about household energy use, and, on the other hand, household members wanting to reduce the energy use by revealing their own habits and thereby finding out how changed activity performance may influence electricity use. The focus is on the relation between utilizing electric appliances to perform everyday life activities and the use of electricity. The visualization method is based on the time-geographic approach developed by Haegerstrand and includes a model that estimates appliance electricity use from household members' activities. Focus, in this paper, is put on some basic activities performed to satisfy daily life needs: cooking and use of information, communication and entertainment devices. These activities appear frequently in the everyday life of households, even though not all household members perform them all. The method is applied on a data material comprising time-diaries written by 463 individuals (aged 10 to 85+) in 179 households in different parts of Sweden. The visualization method reveals when and for how long activities that claim electric appliances are performed by which individual(s). It also shows electricity load curves generated from the use of appliances at different levels, such as individual, household and group or population levels. At household level the method can reveal which household members are the main users of electricity, i.e. the division of labour between household members. Thereby it also informs about whom could be approached by energy companies and energy advisors in information campaigns. The main result of the study is that systematic differences in activity patterns in subgroups of a population can be identified (e.g. men and women) but

Suggested Curriculum Guide for Developing a Program in Appliance Service and Repair. Bulletin No. 48-174.

Science.gov (United States)

Illinois State Board of Vocational Education and Rehabilitation, Springfield. Div. of Vocational and Technical Education.

The outline curriculum guide has been developed to assist in planning, developing, and instructing a program in appliance service and repair. The material consists of a unit outline and suggested exercieses and assignments for 17 areas: shop mathematics, communication skills, safety, orientation to appliance service and repair, blueprint reading,…

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management.

Science.gov (United States)

Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

2018-02-25

The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism.

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

Science.gov (United States)

Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

2018-01-01

The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism. PMID:29495346

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

Directory of Open Access Journals (Sweden)

Bhagya Nathali Silva

2018-02-01

Full Text Available The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism.

Compatibility of fixed orthodontic appliances with MR environment

Czech Academy of Sciences Publication Activity Database

Starčuk jr., Zenon; Hubálková, H.; Starčuková, Jana; Linetskiy, I.; Bartušek, Karel; Krupa, P.

2006-01-01

Roč. 19, Suppl. 1 (2006), EPOS 726:1-7 E-ISSN 1352-8661 R&D Projects: GA MZd NR8110 Institutional research plan: CEZ:AV0Z20650511 Keywords : orthodontic appliance * magnetic resonance * compatibility * dentistry * artifact Subject RIV: FS - Medical Facilities ; Equipment Impact factor: 0.756, year: 2005 http://posters.webges.com/esmrmb/epos

Jeux chez les Touaregs

OpenAIRE

Bernus, E.

2012-01-01

Parmi les jeux pratiqués par les Touaregs, il faut distinguer les jeux sportifs qui opposent deux équipes ou deux hommes, des jeux de société dans un cadre inscrit dans le sable, et les jeux d’esprit, véritables joutes verbales ; enfin, il faut signaler la construction par les enfants de jouets. Un certain nombre de jeux sont connus chez d’autres populations africaines. L’ouvrage de Charles Béart, Jeux et jouets de l’Ouest africain (1955), nous permet d’utiles comparaisons. Il est donc intére...

Changes in oro-pharyngeal airway dimension after treatment with function appliance in class II skeletal pattern

International Nuclear Information System (INIS)

Ali, B.; Shaikh, A.; Fida, M.

2015-01-01

Background: Functional appliances have been used since many decades for the correction of mandibular retrognathism. Similar oral appliances are a treatment modality for patients with Obstructive sleep apnea. Hence, interception at the right age with these growth modification appliances might benefit a child from developing long term respiratory insufficiency. Therefore, the purpose of our study was to assess the short term effects of Twin block appliance (CTB) on pharyngeal airway size in subjects with skeletal Class II pattern in a sample of Pakistani population. Methods: A retrospective study was conducted from orthodontic records of 62 children (31 males, 31 females) with retrognathic mandibles using lateral cephalograms obtained at initial visit and after CTB treatment. Paired t-test was used to compare the pre-functional and post-functional treatment airway size. Independent sample t-test was used for comparison between the genders and statistical significance was kept at =0.05. Results: The upper airway width (p<0.001), nasopharyngeal depth (p=0.03) and upper airway thickness (p=0.008) was substantially improved after CTB treatment. Males showed a greater increase in upper airway width (p= 0.03) and nasopharyngeal depth (p=0.01) in comparison to the females. Conclusion: Functional appliance therapy can improve the narrow pharyngeal airway of growing children presenting with deficient mandibles having Class II skeletal pattern. (author)

Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

OpenAIRE

Bhagya Nathali Silva; Murad Khan; Kijun Han

2018-01-01

The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage...

Mini-screws, a viable adjunct along with Incognito lingual appliance: A case series

Directory of Open Access Journals (Sweden)

Wei Lin

2015-01-01

Full Text Available Invisible orthodontics have been around for too long, and with the advent of computer-aided design/computer-aided manufacturing technology appliances such as Incognito TM has made the whole treatment experience more pleasant and aesthetic. However, even in lingual orthodontics, biomechanics play the most important role, and the use of temporary anchorage devices (TADs has made the whole treatment more effective and efficient. This article focuses on cases where TADs in lingual appliances play a critical role in the treatment of various malocclusions.

Report on an investigation into heat pumps in China in fiscal 1995; 1995 nendo Chugoku ni okeru heat pump system ni kansuru chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper surveyed the present status, the status of spread, and the technical development of the technology of heat pumps for residential and industrial uses in China. Main examples of installation of heat pumps are cited below: steam drive absorption type refrigerators in Beijing; sea water heat source turbo heat pumps in Qingdao; hot water drive absorption type refrigerators in Beijing; oil-fueled absorption type water cooling and heating appliances in Beijing; ice latent heat storage airconditioning systems using electrically-driven screw chiller in Beijing; temperature rising systems using electrically-driven heat pump of the solar energy utilization warm water swimming pool in Guangdong Province; cooling water supply using waste heat utilization absorption type refrigerator of the alcohol plant in Shandong Province; timber drying systems using electrically-driven heat pump, and marine product cultivation systems in Quangdong Province; distillation systems using steam turbine heat pump in Jiangxi Province. The demand for heat pumps is expected to be 20 million units under the 9th 5-year plan, and the development of equipment is thought to go toward promotion of energy conservation, low noise, multi-type or multi-functional air conditioning equipment, and computer use. 137 figs., 40 tabs.

77 FR 21744 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2012-04-11

... Shelving and Racks From the People's Republic of China: Final Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's... Kitchen Appliance Shelving and Racks from the People's Republic of China: Preliminary Results of...