The gene dosage effect of the rad52 mutation on X-ray survival curves of tetraploid yeast strains

International Nuclear Information System (INIS)

Ho, K.S.Y.

1975-01-01

The mutation rad52 in the yeast Saccharomyces cerevisiae confers sensitivity to X-rays. The gene dosage effect of this mutation on X-ray survival curves of tetraploid yeast strains is shown. With increasing number of rad52 alleles, both a decrease in the survival for a given dose and a decrease in the survival curve shoulder width are observed. The generation of such a family of survival curves using three different mathematical models is discussed

Heat rate curve approximation for power plants without data measuring devices

Energy Technology Data Exchange (ETDEWEB)

Poullikkas, Andreas [Electricity Authority of Cyprus, P.O. Box 24506, 1399 Nicosia (CY

2012-07-01

In this work, a numerical method, based on the one-dimensional finite difference technique, is proposed for the approximation of the heat rate curve, which can be applied for power plants in which no data acquisition is available. Unlike other methods in which three or more data points are required for the approximation of the heat rate curve, the proposed method can be applied when the heat rate curve data is available only at the maximum and minimum operating capacities of the power plant. The method is applied on a given power system, in which we calculate the electricity cost using the CAPSE (computer aided power economics) algorithm. Comparisons are made when the least squares method is used. The results indicate that the proposed method give accurate results.

Relation of intracellular cyclic AMP to the shape of mammalian cell survival curves

International Nuclear Information System (INIS)

Lehnert, S.

1975-01-01

Results of experiments with V79 cells growing in tissue culture indicate that the reproductive survival of cells following irradiation is influenced by the level of intracellular 3', 5'-cyclic adenosine monophosphate (cyclic AMP) at the time of irradiation. Cells containing high levels of cyclic AMP induced by treatments with drugs show a characteristic survival curve in which the extent of the shoulder is increased so that the survival after low doses is enhanced. The exponential slope or D 0 , however, is decreased so that at high doses the survival of cells containing high levels of cyclic AMP may be less than that of controls. Naturally occurring changes in radiosensitivity such as those observed as cells pass through the division cycle, may also be related to parallel changes in cyclic AMP concentration occurring during the cycle. Injection of mice with compounds producing elevated cyclic AMP prior to whole-body irradiation increases survival at seven days post-irradiation. The shape of the survival curve for intestinal stem cells in these mice differs from that of the control in having an increased extrapolation number; no change in D 0 is observed in this in vivo situation. (author)

Implications of tissue target-cell survival-curve shape for values of split-dose recovery doses: late versus early effects

International Nuclear Information System (INIS)

Redpath, J.L.; Peel, D.M.; Hopewell, J.W.

1984-01-01

Recent data from this laboratory on split-dose recovery for early and late effects in pig skin are consistent with the linear-quadratic model for cell survival, and with relative cell survival-curve shapes for early- and late-effect target cells where the early-effect cells have an intially steeper and straighter survival-curve than the late-effect cells. (author)

Transient, heat-induced thermal resistance in the small intestine of mouse

International Nuclear Information System (INIS)

Hume, S.P.; Marigold, J.C.L.

1980-01-01

Heat-induced thermal resistance has been investigated in mouse jejunum by assaying crypt survival 24 h after treatment. Hyperthermia was achieved by immersing an exteriorized loop of intestine in a bath of Krebs-Ringer solution. Two approaches have been used. In the first, thermal survival curves were obtained following single hyperthermal treatments at temperatures in the range 42 to 44 0 C. Transient thermal resistance, inducted by a plateau in the crypt survival curve, developed during heating at temperatures around 42.5 0 C after 60 to 80 min. In the second series of experiments, a priming heat treatment (40.0, 41.0, 41.5, or 42.0 0 C for 60 min) was followed at varying intervals by a test treatment at 43.0 0 C. A transient resistance to the second treatment was induced, the extent and time of development being dependent upon the priming treatment. Crypt survival curves for thermally resistant intestine showed an increase in thermal D 0 and a decrease in n compared with curves from previously unheated intestine

The effect of buoyancy on flow and heat transfer in curved pipes

OpenAIRE

Mochizuki, Munekazu; Ishigaki, Hiroshi; 望月 宗和; 石垣 博

1994-01-01

Fully developed laminar flow in a heated horizontal curved pipe is studied numerically. The thermal boundary conditions at the wall are uniform wall heat flux axially and uniform wall temperature peripherally. Flow and heat transfer are governed by Dean number, Prandtl number and buoyancy number. Detailed prediction of the friction factor, average heat transfer rate, velocity profile, temperature profile and secondary-flow streamlines are given.

Exponential Decay Nonlinear Regression Analysis of Patient Survival Curves: Preliminary Assessment in Non-Small Cell Lung Cancer

Science.gov (United States)

Stewart, David J.; Behrens, Carmen; Roth, Jack; Wistuba, Ignacio I.

2010-01-01

Background For processes that follow first order kinetics, exponential decay nonlinear regression analysis (EDNRA) may delineate curve characteristics and suggest processes affecting curve shape. We conducted a preliminary feasibility assessment of EDNRA of patient survival curves. Methods EDNRA was performed on Kaplan-Meier overall survival (OS) and time-to-relapse (TTR) curves for 323 patients with resected NSCLC and on OS and progression-free survival (PFS) curves from selected publications. Results and Conclusions In our resected patients, TTR curves were triphasic with a “cured” fraction of 60.7% (half-life [t1/2] >100,000 months), a rapidly-relapsing group (7.4%, t1/2=5.9 months) and a slowly-relapsing group (31.9%, t1/2=23.6 months). OS was uniphasic (t1/2=74.3 months), suggesting an impact of co-morbidities; hence, tumor molecular characteristics would more likely predict TTR than OS. Of 172 published curves analyzed, 72 (42%) were uniphasic, 92 (53%) were biphasic, 8 (5%) were triphasic. With first-line chemotherapy in advanced NSCLC, 87.5% of curves from 2-3 drug regimens were uniphasic vs only 20% of those with best supportive care or 1 drug (p<0.001). 54% of curves from 2-3 drug regimens had convex rapid-decay phases vs 0% with fewer agents (p<0.001). Curve convexities suggest that discontinuing chemotherapy after 3-6 cycles “synchronizes” patient progression and death. With postoperative adjuvant chemotherapy, the PFS rapid-decay phase accounted for a smaller proportion of the population than in controls (p=0.02) with no significant difference in rapid-decay t1/2, suggesting adjuvant chemotherapy may move a subpopulation of patients with sensitive tumors from the relapsing group to the cured group, with minimal impact on time to relapse for a larger group of patients with resistant tumors. In untreated patients, the proportion of patients in the rapid-decay phase increased (p=0.04) while rapid-decay t1/2 decreased (p=0.0004) with increasing

Mathematical analysis of 51Cr-labelled red cell survival curves in congenital haemolytic anaemias

International Nuclear Information System (INIS)

Kasfiki, A.G.; Antipas, S.E.; Dimitriou, P.A.; Gritzali, F.A.; Melissinos, K.G.

1982-01-01

The parameters of 51 Cr labelled red cell survival curves were calculated in 26 patients with homozygous β-thalassaemia, 8 with sickle-cell anaemia and 3 with s-β-thalassaemia, using a non-linear weighted least squares analysis computer program. In thalassaemic children the calculated parameters denote that the shorting of the mean cell life is due to early senescence alone, while there is some evidence that in thalassaemic adults additional extracellular destruction mechanisms participate as well. Red cell survival curves from patients with sickle-cell anaemia and s-β-thalassaemia resemble each other, while their parameters indicate an initial rapid loss of radioactivity, early senescence and the presence of extracellular red cell destruction factors. (orig.)

Intercellular contact: its influence on the Dsub(q) of mammalian cell survival curves

International Nuclear Information System (INIS)

Durand, R.E.; Sutherland, R.M.

1975-01-01

Cell survival in tissues exposed to a given dose of ionizing radiation is usually greater than that of similar cells grown individually in vitro, despite the fact that the radiosensitivities (D 0 ) are virtually identical under the two conditions. An analogous increase in cell survival is observed when Chinese hamster V79-171 cells are grown in suspension culture and irradiated as multicell spheroids. Unfortunately, the information gained from the survival curves so obtained is limited by the inhomogeneity of the cell population with respect to both degree of contact and cell cycle position. The latter can be studied using synchronized small spheroids. The ratio of Dsub(q) of spheroid cells to Dsub(q) of single cells increased as the cells progressed through the cell cycle, from a minimum of 1.3 for G 1 phase cells to a maximum of 2.2 for late S-phase cells. The enhanced survival, or 'contact effect', developed slowly as the spheroids grew, after an initial latent period of about one generation cycle of the cells. A second effect of intercellular contact on mammalian cell survival has also been observed. When cells are assayed under conditions in which intercellular contact is maintained, the net cellular survival is increased further. This effect is different from the usual repair of potentially lethal damage, in that it occurs much more slowly and results in modification of the survival-curve shoulder. Not all cell types tested have shown enhanced survival when grown as spheroids. Several MNNG-induced mutants of the Chinese hamster V79-171 line have been isolated and sublines which do and do not show the contact effect are now available. These may permit study of the mechanism(s) of contact effects. (author)

Evaluating methodological assumptions of a catch-curve survival estimation of unmarked precocial shorebird chickes

Science.gov (United States)

McGowan, Conor P.; Gardner, Beth

2013-01-01

Estimating productivity for precocial species can be difficult because young birds leave their nest within hours or days of hatching and detectability thereafter can be very low. Recently, a method for using a modified catch-curve to estimate precocial chick daily survival for age based count data was presented using Piping Plover (Charadrius melodus) data from the Missouri River. However, many of the assumptions of the catch-curve approach were not fully evaluated for precocial chicks. We developed a simulation model to mimic Piping Plovers, a fairly representative shorebird, and age-based count-data collection. Using the simulated data, we calculated daily survival estimates and compared them with the known daily survival rates from the simulation model. We conducted these comparisons under different sampling scenarios where the ecological and statistical assumptions had been violated. Overall, the daily survival estimates calculated from the simulated data corresponded well with true survival rates of the simulation. Violating the accurate aging and the independence assumptions did not result in biased daily survival estimates, whereas unequal detection for younger or older birds and violating the birth death equilibrium did result in estimator bias. Assuring that all ages are equally detectable and timing data collection to approximately meet the birth death equilibrium are key to the successful use of this method for precocial shorebirds.

Blood flow in curved pipe with radiative heat transfer

International Nuclear Information System (INIS)

Ogulu, A.; Bestman, A.R.

1992-03-01

Blood flow in a curved pipe such as the aorta is modelled in this study. The aorta is modelled as a curved pipe of slowly varying cross-section. Asymptotic series expansions about a small parameter δ, which is a measure of the curvature ratio is employed to obtain the velocity and temperature distributions. The study simulates the effect of radio-frequency heating, for instance during physiotherapy, on the flow of blood in the cardiovascular system assuming an external constant pressure gradient; and our results agree very well with results obtained by Pedley. (author). 9 refs, 2 figs

Heat transfer and pressure drop characteristics of the tube bank fin heat exchanger with fin punched with flow redistributors and curved triangular vortex generators

Science.gov (United States)

Liu, Song; Jin, Hua; Song, KeWei; Wang, LiangChen; Wu, Xiang; Wang, LiangBi

2017-10-01

The heat transfer performance of the tube bank fin heat exchanger is limited by the air-side thermal resistance. Thus, enhancing the air-side heat transfer is an effective method to improve the performance of the heat exchanger. A new fin pattern with flow redistributors and curved triangular vortex generators is experimentally studied in this paper. The effects of the flow redistributors located in front of the tube stagnation point and the curved vortex generators located around the tube on the characteristics of heat transfer and pressure drop are discussed in detail. A performance comparison is also carried out between the fins with and without flow redistributors. The experimental results show that the flow redistributors stamped out from the fin in front of the tube stagnation points can decrease the friction factor at the cost of decreasing the heat transfer performance. Whether the combination of the flow redistributors and the curved vortex generators will present a better heat transfer performance depends on the size of the curved vortex generators. As for the studied two sizes of vortex generators, the heat transfer performance is promoted by the flow redistributors for the fin with larger size of vortex generators and the performance is suppressed by the flow redistributors for the fin with smaller vortex generators.

Finding Risk Groups by Optimizing Artificial Neural Networks on the Area under the Survival Curve Using Genetic Algorithms.

Science.gov (United States)

Kalderstam, Jonas; Edén, Patrik; Ohlsson, Mattias

2015-01-01

We investigate a new method to place patients into risk groups in censored survival data. Properties such as median survival time, and end survival rate, are implicitly improved by optimizing the area under the survival curve. Artificial neural networks (ANN) are trained to either maximize or minimize this area using a genetic algorithm, and combined into an ensemble to predict one of low, intermediate, or high risk groups. Estimated patient risk can influence treatment choices, and is important for study stratification. A common approach is to sort the patients according to a prognostic index and then group them along the quartile limits. The Cox proportional hazards model (Cox) is one example of this approach. Another method of doing risk grouping is recursive partitioning (Rpart), which constructs a decision tree where each branch point maximizes the statistical separation between the groups. ANN, Cox, and Rpart are compared on five publicly available data sets with varying properties. Cross-validation, as well as separate test sets, are used to validate the models. Results on the test sets show comparable performance, except for the smallest data set where Rpart's predicted risk groups turn out to be inverted, an example of crossing survival curves. Cross-validation shows that all three models exhibit crossing of some survival curves on this small data set but that the ANN model manages the best separation of groups in terms of median survival time before such crossings. The conclusion is that optimizing the area under the survival curve is a viable approach to identify risk groups. Training ANNs to optimize this area combines two key strengths from both prognostic indices and Rpart. First, a desired minimum group size can be specified, as for a prognostic index. Second, the ability to utilize non-linear effects among the covariates, which Rpart is also able to do.

Heat response of mouse tumor cells treated with 5-thio-D-glucose and Rhodamine-123

International Nuclear Information System (INIS)

Rhee, J.G.; Lyons, J.C.; Song, C.W.

1987-01-01

Cellular heat-sensitivity has been known to depend on intracellular energy. The authors studied the thermal response of cultured SCK mammary carcinoma cells in vitro, following glycolytic inhibition with 5-thio-D-glucose (TG) and mitochondrial inactivation with Rhodamine-123 (Rh). The cells in exponential growth phase in RPMI 1640 medium supplemented with serum and antibiotics were exposed to medium containing Rh and/or TG, heated in a prewarmed water bath, and the clonogenic survivals of the heated cells were determined. Thermal cell killing by the 30 min. heating was increased, when 10 and 20 μg/ml Rh were present in the medium at temperatures above 42 0 and 40 0 C, respectively. The slope of the heat survival curve for 43 0 C heating became steeper in the presence of 10 and 20 μg/ml Rh, and the initial shoulder of the survival curve was unaltered at the dose of 10 μg/ml Rh, but disappeared at 20 μg/ml. A TG dose of 3 mg/ml, which is about 10 times that necessary to kill 90% of cells in 5 hrs. under hypoxic condition, was ineffective in altering any parameters of the heat survival curve of aerobic cells. The combined effect of TG and Rh on the thermal cell killing in aerobic condition did not exceed the effect of Rh alone. The above results indicate that the energy supply derived by mitochondria is an important determinant for the shape of heat survival curve of the proliferating and aerobic SCK tumor cells

Turbulent Heat Transfer in Curved Pipe Flow

Science.gov (United States)

Kang, Changwoo; Yang, Kyung-Soo

2013-11-01

In the present investigation, turbulent heat transfer in fully-developed curved pipe flow with axially uniform wall heat flux has been numerically studied. The Reynolds numbers under consideration are Reτ = 210 (DNS) and 1,000 (LES) based on the mean friction velocity and the pipe radius, and the Prandtl number (Pr) is 0.71. For Reτ = 210 , the pipe curvature (κ) was fixed as 1/18.2, whereas three cases of κ (0.01, 0.05, 0.1) were computed in the case of Reτ = 1,000. The mean velocity, turbulent intensities and heat transfer rates obtained from the present calculations are in good agreement with the previous numerical and experimental results. To elucidate the secondary flow structures due to the pipe curvature, the mean quantities and rms fluctuations of the flow and temperature fields are presented on the pipe cross-sections, and compared with those of the straight pipe flow. To study turbulence structures and their influence on turbulent heat transfer, turbulence statistics including but not limited to skewness and flatness of velocity fluctuations, cross-correlation coefficients, an Octant analysis, and turbulence budgets are presented and discussed. Based on our results, we attempt to clarify the effects of Reynolds number and the pipe curvature on turbulent heat transfer. This research was supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2010-0008457).

Statistical inference methods for two crossing survival curves: a comparison of methods.

Science.gov (United States)

Li, Huimin; Han, Dong; Hou, Yawen; Chen, Huilin; Chen, Zheng

2015-01-01

A common problem that is encountered in medical applications is the overall homogeneity of survival distributions when two survival curves cross each other. A survey demonstrated that under this condition, which was an obvious violation of the assumption of proportional hazard rates, the log-rank test was still used in 70% of studies. Several statistical methods have been proposed to solve this problem. However, in many applications, it is difficult to specify the types of survival differences and choose an appropriate method prior to analysis. Thus, we conducted an extensive series of Monte Carlo simulations to investigate the power and type I error rate of these procedures under various patterns of crossing survival curves with different censoring rates and distribution parameters. Our objective was to evaluate the strengths and weaknesses of tests in different situations and for various censoring rates and to recommend an appropriate test that will not fail for a wide range of applications. Simulation studies demonstrated that adaptive Neyman's smooth tests and the two-stage procedure offer higher power and greater stability than other methods when the survival distributions cross at early, middle or late times. Even for proportional hazards, both methods maintain acceptable power compared with the log-rank test. In terms of the type I error rate, Renyi and Cramér-von Mises tests are relatively conservative, whereas the statistics of the Lin-Xu test exhibit apparent inflation as the censoring rate increases. Other tests produce results close to the nominal 0.05 level. In conclusion, adaptive Neyman's smooth tests and the two-stage procedure are found to be the most stable and feasible approaches for a variety of situations and censoring rates. Therefore, they are applicable to a wider spectrum of alternatives compared with other tests.

Extension of the master sintering curve for constant heating rate modeling

Science.gov (United States)

McCoy, Tammy Michelle

The purpose of this work is to extend the functionality of the Master Sintering Curve (MSC) such that it can be used as a practical tool for predicting sintering schemes that combine both a constant heating rate and an isothermal hold. Rather than just being able to predict a final density for the object of interest, the extension to the MSC will actually be able to model a sintering run from start to finish. Because the Johnson model does not incorporate this capability, the work presented is an extension of what has already been shown in literature to be a valuable resource in many sintering situations. A predicted sintering curve that incorporates a combination of constant heating rate and an isothermal hold is more indicative of what is found in real-life sintering operations. This research offers the possibility of predicting the sintering schedule for a material, thereby having advanced information about the extent of sintering, the time schedule for sintering, and the sintering temperature with a high degree of accuracy and repeatability. The research conducted in this thesis focuses on the development of a working model for predicting the sintering schedules of several stabilized zirconia powders having the compositions YSZ (HSY8), 10Sc1CeSZ, 10Sc1YSZ, and 11ScSZ1A. The compositions of the four powders are first verified using x-ray diffraction (XRD) and the particle size and surface area are verified using a particle size analyzer and BET analysis, respectively. The sintering studies were conducted on powder compacts using a double pushrod dilatometer. Density measurements are obtained both geometrically and using the Archimedes method. Each of the four powders is pressed into ¼" diameter pellets using a manual press with no additives, such as a binder or lubricant. Using a double push-rod dilatometer, shrinkage data for the pellets is obtained over several different heating rates. The shrinkage data is then converted to reflect the change in relative

Discrimination measures for survival outcomes: connection between the AUC and the predictiveness curve.

Science.gov (United States)

Viallon, Vivian; Latouche, Aurélien

2011-03-01

Finding out biomarkers and building risk scores to predict the occurrence of survival outcomes is a major concern of clinical epidemiology, and so is the evaluation of prognostic models. In this paper, we are concerned with the estimation of the time-dependent AUC--area under the receiver-operating curve--which naturally extends standard AUC to the setting of survival outcomes and enables to evaluate the discriminative power of prognostic models. We establish a simple and useful relation between the predictiveness curve and the time-dependent AUC--AUC(t). This relation confirms that the predictiveness curve is the key concept for evaluating calibration and discrimination of prognostic models. It also highlights that accurate estimates of the conditional absolute risk function should yield accurate estimates for AUC(t). From this observation, we derive several estimators for AUC(t) relying on distinct estimators of the conditional absolute risk function. An empirical study was conducted to compare our estimators with the existing ones and assess the effect of model misspecification--when estimating the conditional absolute risk function--on the AUC(t) estimation. We further illustrate the methodology on the Mayo PBC and the VA lung cancer data sets. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of survival curves for Rhizopus, Mucor and Penicillia irradiated with gamma radiation

International Nuclear Information System (INIS)

Ishiguro, Etsuji; Danno, Akibumi; Miyazato, Mitsuru

1994-01-01

This study was aimed to understand the survival pattern of some microorganisms which were treated by γ-sterilization. Though most of the works were concentrated and reported with D 10 -values, it was presently found that the γ-irradiated survival curves showed sigmoid pattern and L-values were reached about half of the D 10 -value for each strains. It was further confirmed that if L-values were used for practical sterilization with D 10 -values, the estimation of sterilized levels would become more accurate. (author). 10 refs., 3 figs., 1 tab

Universal Survival Curve and Single Fraction Equivalent Dose: Useful Tools in Understanding Potency of Ablative Radiotherapy

International Nuclear Information System (INIS)

Park, Clint; Papiez, Lech; Zhang Shichuan; Story, Michael; Timmerman, Robert D.

2008-01-01

Purpose: Overprediction of the potency and toxicity of high-dose ablative radiotherapy such as stereotactic body radiotherapy (SBRT) by the linear quadratic (LQ) model led to many clinicians' hesitating to adopt this efficacious and well-tolerated therapeutic option. The aim of this study was to offer an alternative method of analyzing the effect of SBRT by constructing a universal survival curve (USC) that provides superior approximation of the experimentally measured survival curves in the ablative, high-dose range without losing the strengths of the LQ model around the shoulder. Methods and Materials: The USC was constructed by hybridizing two classic radiobiologic models: the LQ model and the multitarget model. We have assumed that the LQ model gives a good description for conventionally fractionated radiotherapy (CFRT) for the dose to the shoulder. For ablative doses beyond the shoulder, the survival curve is better described as a straight line as predicted by the multitarget model. The USC smoothly interpolates from a parabola predicted by the LQ model to the terminal asymptote of the multitarget model in the high-dose region. From the USC, we derived two equivalence functions, the biologically effective dose and the single fraction equivalent dose for both CFRT and SBRT. Results: The validity of the USC was tested by using previously published parameters of the LQ and multitarget models for non-small-cell lung cancer cell lines. A comparison of the goodness-of-fit of the LQ and USC models was made to a high-dose survival curve of the H460 non-small-cell lung cancer cell line. Conclusion: The USC can be used to compare the dose fractionation schemes of both CFRT and SBRT. The USC provides an empirically and a clinically well-justified rationale for SBRT while preserving the strengths of the LQ model for CFRT

The Hardy inequality and the heat flow in curved wedges

Czech Academy of Sciences Publication Activity Database

Krejčiřík, David

2016-01-01

Roč. 73, č. 2 (2016), s. 91-113 ISSN 0032-5155 R&D Projects: GA ČR(CZ) GA14-06818S Institutional support: RVO:61389005 Keywords : Hardy inequality * heat equation * large-time behaviour * curved wedges * Dirichlet Laplacian * conical singularities * Brownian motion * subcriticality Subject RIV: BE - Theoretical Physics Impact factor: 0.735, year: 2016

Survival curves and cell restoration of gamma irradiated chlorella

International Nuclear Information System (INIS)

Gilet, Roland

1970-01-01

The characteristics of the living material used and the cultures developed are defined. The irradiation techniques and the dosimetry methods used are described. The clonal growth in a gelified nutrient solution was studied and the survival curves, which are very reproducible when anoxic conditions are eliminated, were established. It is shown that the radiosensitivity of Chlorella decreases with the age of the culture when the plateau of the growth curve is reached, and that for synchronous cells it varies slightly with the phase in the cycle at which the radiation is received. The restoration from sublethal damage occurs quickly and does not depend upon the continuation of the cell cycle when no multiplication occurs during the experiments and is not modified by anoxic conditions. The restoration rate is reduced at 0 deg. C. It explains the variations in the apparent radiosensitivity with the dose rate. In contrast with the results published for many cells, the restoration is incomplete. The problem of the elimination of sublethal damage during clonal development is posed. A model summarizing the experimental results and suggesting future work is given. (author) [fr

Survival of encapsulated Lactobacillus plantarum during isothermal heating and bread baking

NARCIS (Netherlands)

Zhang, L.; Chen, Xiao Dong; Boom, R.M.; Schutyser, M.A.I.

2018-01-01

The effect of encapsulation on the survival of Lactobacillus plantarum during isothermal heating and bread baking was investigated. Four encapsulating materials were evaluated, i.e., reconstituted skim milk (RSM), gum arabic (GA), maltodextrin (MD) and inulin. Freeze dried bacteria survived better

Greenhouse gas abatement cost curves of the residential heating market. A microeconomic approach

International Nuclear Information System (INIS)

Dieckhoener, Caroline; Hecking, Harald

2012-01-01

In this paper, we develop a microeconomic approach to deduce greenhouse gas abatement cost curves of the residential heating sector. By accounting for household behavior, we find that welfare-based abatement costs are generally higher than pure technical equipment costs. Our results are based on a microsimulation of private households' investment decision for heating systems until 2030. The households' investment behavior in the simulation is derived from a discrete choice estimation which allows investigating the welfare costs of different abatement policies in terms of the compensating variation and the excess burden. We simulate greenhouse gas abatements and welfare costs of carbon taxes and subsidies on heating system investments until 2030 to deduce abatement curves. Given utility maximizing households, our results suggest a carbon tax to be the welfare efficient policy. Assuming behavioral misperceptions instead, a subsidy on investments might have lower marginal greenhouse gas abatement costs than a carbon tax.

Statistical study of clone survival curves after irradiation in one or two stages. Comparison and generalization of different models

International Nuclear Information System (INIS)

Lachet, Bernard.

1975-01-01

A statistical study was carried out on 208 survival curves for chlorella subjected to γ or particle radiations. The computing programmes used were written in Fortran. The different experimental causes contributing to the variance of a survival rate are analyzed and consequently the experiments can be planned. Each curve was fitted to four models by the weighted least squares method applied to non-linear functions. The validity of the fits obtained can be checked by the F test. It was possible to define the confidence and prediction zones around an adjusted curve by weighting of the residual variance, in spite of error on the doses delivered; the confidence limits can them be fixed for a dose estimated from an exact or measured survival. The four models adopted were compared for the precision of their fit (by a non-parametric simultaneous comparison test) and the scattering of their adjusted parameters: Wideroe's model gives a very good fit with the experimental points in return for a scattering of its parameters, which robs them of their presumed meaning. The principal component analysis showed the statistical equivalence of the 1 and 2 hit target models. Division of the irradiation into two doses, the first fixed by the investigator, leads to families of curves for which the equation was established from that of any basic model expressing the dose survival relationship in one-stage irradiation [fr

Assessment of CHF enhancement mechanisms in a curved, rectangular channel subjected to concave heating

International Nuclear Information System (INIS)

Sturgis, J.C.; Mudawar, I.

1999-01-01

An experimental study was undertaken to examine the enhancement in critical heat flux (CHF) provided by streamwise curvature. Curved and straight rectangular flow channels were fabricated with identical 5.0 x 2.5 mm cross sections and heated lengths of 101.6 mm in which the heat was applied to only one wall--the concave wall (32.3 mm radius) in the curved channel and a side wall in the straight. Tests were conducted using FC-72 liquid with mean inlet velocity and outlet subcooling of 0.25 to 10 m s -1 and 3 to 29 C, respectively. Centripetal acceleration for curved flow reached 315 times earth's gravitational acceleration. Critical heat flux was enhanced due to flow curvature at all conditions but the enhancement decreased with increasing subcooling. For near-saturated conditions, the enhancement was approximately 60% while for highly subcooled flow it was only 20%. The causes for the enhancement were identified as (1) increased pressure on the liquid-vapor interface at wetting fronts, (2) buoyancy forces and (3) increased subcooling at the concave wall. Flow visualization tests were conducted in transparent channels to explore the role of buoyancy forces in enhancing the critical heat flux. These forces were observed to remove vapor from the concave wall and distribute it throughout the cross section. Vapor removal was only effective at near-saturated conditions, yielding the observed substantial enhancement in CHF relative to the straight channel

The effect of ploidy on the modification of the shoulder region of hypoxic cell-survival curves by the biradical, Ro.03-6061

International Nuclear Information System (INIS)

Millar, B.C.; Millar, J.L.

1977-01-01

The biradical nitroxyl, Ro.03-6061, sensitized two lines of mouse L cell to ionizing radiation when the cells were rendered hypoxic. Although the biradical reduced the D 0 value of the hypoxic cell-survival curve in each instance, it had no significant effect on the shoulder region. A hybrid line produced from these two strains was more radioresistant than either parent. In this instance, the biradical suppressed the shoulder region of the hypoxic cell-survival curve, but had no effect on the D 0 value. In a second system, the biradical selectivity sensitized hypoxic cells of a diploid and a tetraploid clone of Syrian hamster cells (BHK21/C15). The survival-curve characteristics of both clones were similar. The biradical reduced the D 0 value but did not significantly change the shoulder region of the hypoxic cell-survival curve. An aneuploid line sub-cultured from the tetraploid clone was much more resistant to radiation. In this instance, there was a decrease in the D 0 value of hypoxic cells in the presence of the biradical, but the extrapolation number was increased to a value similar to that for cells irradiated in air. (author)

Temperature dependence of heat sensitization and thermotolerance induction with ethanol

International Nuclear Information System (INIS)

Henle, K.J.; Nagle, W.A.; Moss, A.J.

1987-01-01

Cytoxicity of 1 M ethanol was strongly temperature dependent; survival curves between 34 0 and 39 0 C were similar to heat survival curves between 40 and 45 0 without ethanol. Ethanol was non-toxic at 22 0 ; at 34.5 0 and 35.5 0 ethanol survival curves were biphasic. The major effect of 1 M ethanol was an effective temperature shift of 6.4 Celsius degrees, although temperatures between 34 0 and 36 0 caused additional sensitization reminiscent of the stepdown heating phenomenon. Induction of thermotolerance with equitoxic ethanol exposures at 35.5 0 and 37 0 or with heat alone (10 min, 45 0 ) resulted in tolerance development with similar kinetics; in contrast, ethanol exposures at 22 0 did not induce any tolerance development with similar kinetics; in contrast, ethanol exposures at 22 0 did not induce any tolerance to hyperthermia. These data provide a rationale for conflicting reports in the literature regarding thermotolerance induction by ethanol and suggest that ethanol causes ''heat'' stress at temperatures that are generally considered to be physiological. This interpretation predicts that the use of ethanol and other organic solvents in high concentrations will cause effects at 37 0 that normally occur only at hyperthermic temperatures, including membrane perturbations and HSP synthesis, and that ''physiological'' temperatures must be precisely controlled under those conditions

Mathematical simulation of influence of irradiated cell reparative system saturation on cell survival. Communication 1. Simulation of survival curves in prokaryotes

International Nuclear Information System (INIS)

Knyigavko, V.G.; Meshcheryakova, O.P.; Radzyishevs'ka, Je.B.

2004-01-01

Mathematical models of the processes of forming survival curves for prokaryotes which are based on the idea about the possibility of saturation of radiation lesion reparation systems of DNA of the irradiated cells at the dose increase were worked out. For the simplest of the discussed models the authors discuss the question about the methods of evaluation of the model parameters

SU-E-T-429: Uncertainties of Cell Surviving Fractions Derived From Tumor-Volume Variation Curves

International Nuclear Information System (INIS)

Chvetsov, A

2014-01-01

Purpose: To evaluate uncertainties of cell surviving fraction reconstructed from tumor-volume variation curves during radiation therapy using sensitivity analysis based on linear perturbation theory. Methods: The time dependent tumor-volume functions V(t) have been calculated using a twolevel cell population model which is based on the separation of entire tumor cell population in two subpopulations: oxygenated viable and lethally damaged cells. The sensitivity function is defined as S(t)=[δV(t)/V(t)]/[δx/x] where δV(t)/V(t) is the time dependent relative variation of the volume V(t) and δx/x is the relative variation of the radiobiological parameter x. The sensitivity analysis was performed using direct perturbation method where the radiobiological parameter x was changed by a certain error and the tumor-volume was recalculated to evaluate the corresponding tumor-volume variation. Tumor volume variation curves and sensitivity functions have been computed for different values of cell surviving fractions from the practically important interval S 2 =0.1-0.7 using the two-level cell population model. Results: The sensitivity functions of tumor-volume to cell surviving fractions achieved a relatively large value of 2.7 for S 2 =0.7 and then approached zero as S 2 is approaching zero Assuming a systematic error of 3-4% we obtain that the relative error in S 2 is less that 20% in the range S2=0.4-0.7. This Resultis important because the large values of S 2 are associated with poor treatment outcome should be measured with relatively small uncertainties. For the very small values of S2<0.3, the relative error can be larger than 20%; however, the absolute error does not increase significantly. Conclusion: Tumor-volume curves measured during radiotherapy can be used for evaluation of cell surviving fractions usually observed in radiation therapy with conventional fractionation

Characterization of Radial Curved Fin Heat Sink under Natural and Forced Convection

Science.gov (United States)

Khadke, Rishikesh; Bhole, Kiran

2018-02-01

Heat exchangers are important structures widely used in power plants, food industries, refrigeration, and air conditioners and now widely used in computing systems. Finned type of heat sink is widely used in computing systems. The main aim of the design of the heat sink is to maintain the optimum temperature level. To achieve this goal so many geometrical configurations are implemented. This paper presents a characterization of radially curved fin heat sink under natural and forced convection. Forced convection is studied for the optimization of temperature for better efficiency. The different alternatives in geometry are considered in characterization are heat intensity, the height of the fin and speed of the fan. By recognizing these alternatives the heat sink is characterized by the heat flux usually generated in high-end PCs. The temperature drop characteristics across height and radial direction are presented for the constant heat input and air flow in the heat sink. The effect of dimensionless elevation height (0 ≤ Z* ≤ 1) and Elenbaas Number (0.4 ≤ El ≤ 2.8) of the heat sink were investigated for study of the Nusselt number. Based on experimental characterization, process plan has been developed for the selection of the similar heat sinks for desired output (heat dissipation and temperature distribution).

Heat capacities and asymmetric criticality of the (liquid + liquid) coexistence curves for {dimethyl carbonate + n-undecane, or n-tridecane}

International Nuclear Information System (INIS)

Chen, Zhiyun; Shi, Aiqin; Liu, Shixia; Yin, Tianxiang; Shen, Weiguo

2014-01-01

Highlights: • Coexistence curves of dimethyl carbonate + n-undecane (or + n-tridecane) were measured. • Isobaric heat capacity per unit volume of critical binary solutions dimethyl carbonate + n-undecane (or + n-tridecane) were determined. • The critical exponent β are consistent with the 3D-Ising value. • The asymmetry of the coexistence curves were discussed by the complete scaling theory. - Abstract: The (liquid + liquid) coexistences and the critical behavior of isobaric heat capacity per unit volume for critical binary solutions {dimethyl carbonate + n-undecane, or n-tridecane} have been studied. The critical exponents β and α were deduced and found to be consistent with the 3D-Ising values. The critical amplitudes were determined and used to test the asymmetric criticality of coexistence curves. It was found that the heat capacity does play an important role in describing the asymmetric criticality of the coexistence curves

Factors determinating the shape of survival curves of Escherichia coli cells irradiated by ionizing radiation with different LET. Peculiarities of genom organization and the shape of survival curves

International Nuclear Information System (INIS)

Krasavin, E.A.

1984-01-01

The basic biological mechanisms realized on molecular, cellular and population levels and stipulating the shape of dependence of the cell suriival (S) on the dose (D) are considered. One of possible causes of nonlinear S(D) dependence are the peculiarities of DNA degradation in E. coli cells. The mechanisms of genetic control of different types of degradation are discussed. Some regularities of the genetic recombination and replication of DNA in E. coli are considered. The conclusion is made that one of the basic stipulating for the shoulder on the survival curves in E. coli are the peculiarities of the chromosome replication

The effect of sub-lethal damage repair and exchange on the final slope of cell survival curves

International Nuclear Information System (INIS)

Carlone, M.C.; Wilkins, D.E.; Raaphorst, G.P.

2003-01-01

Full text: The Lea-Catcheside dose rate protraction factor, G, is the most widely used model to describe the effects of dose rate on cell survival. In the linear quadratic formalism, this factor modifies the beta component of cell killing; G is greatest for acute irradiations while vanishing at low dose rates. We have found a simple compartmental model that can derive the Lea-Catcheside function. This compartmental model clearly shows that the G function can only be derived using a little known assumption: the diminution of sub-lethal damage due to exchange of repairable lesions is negligible compared to that due to repair. This assumption was explicitly stated by Lea, but it does not appear to have been restated or verified since very early work on cell survival. The implication of this assumption is that sub-lethal damage can be modeled without considering exchange, which is evidenced by the fact that the G function does not contain parameters relating to exchange. By using a new model that fully accounts for repair and exchange of sublethal lesions, a cell survival expression that has a modified G function, but that retains the linear quadratic formalism, can be obtained. At low doses, this new model predicts linear-quadratic behavior, but the behavior gradually changes to mono-exponential at high doses, which is consistent with experimental observations. Modeling cell survival of well-known survival curves using the modified linear quadratic model shows statistically significant improvement in the fits to the cell survival data as compared to best fits obtained with the linear quadratic model. It is shown that these improvements in fits are due to a superior representation of the high dose region of the survival curve

Heating Processes Of The Axle-Boxes Of Rolling-Stock On Railway Track Curves

Directory of Open Access Journals (Sweden)

Olegas Lunys

2013-12-01

Full Text Available The article deals with the heating process of the axle-boxes ofrolling stock when the train is in motion and discusses the forcesacting on the wheel-set when rolling stock moves along the trackcurves. The paper analyses scientific publications relevant tothe forces acting on the wheel-set of rolling stock and focuseson the axle-box heating process. The article also discusses theresults of theoretical studies on wheel-set forces that affect theheat exchange process of axle-boxes for a railway vehicle. Theresearch has determined a change in heating temperatures ofdifferent axle-boxes of rolling stock and reasons for their variationsand tendencies. The paper has estimated an effect of thetrain running along the track curves on the heating intensity ofthe axle-box. Finally, valid conclusions and recommendationshave been provided.

Numerical analysis of unsteady conjugate heat transfer for initial evolution of thermal stratification in a curved pipe

International Nuclear Information System (INIS)

Jo, Jong Chull; Kim, Wee Kyung; Kim, Yun Il; Cho, Sang Jin; Choi, Seok Ki

2000-01-01

A detailed numerical analysis of initial evolution of thermal stratification in a curved pipe with a finite wall thickness is performed. A primary emphasis of the present study is placed on the investigation of the effect of existence of pipe wall thickness on the evolution of thermal stratification. A simple and convenient numerical method of treating the unsteady conjugate heat transfer in Cartesian as well as non-orthogonal coordinate systems is presented. The proposed unsteady conjugate heat transfer analysis method is implemented in a finite volume thermal-hydraulic computer code based on a cell-centered, non-staggered grid arrangement, the SIMPLEC algorithm and a higher-order bounded convection scheme. Calculations are performed for initial evolution of thermal stratification with high Richardson number in a curved pipe. The predicted results show that the thermally stratified flow and transient conjugate heat transfer in a curved pipe with a specified wall thickness can be satisfactorily analyzed by using the numerical method presented in this paper. As the result, the present analysis method is considered to be effective for the determination of transient temperature distributions in the wall of curved piping system subjected to internally thermal stratification. In addition, the method can be extended to be applicable for the simulation of turbulent flow of thermally stratified fluid

Cell survival curves deduced from non-quantitative reactions of skin, intestinal mucosa and lung

International Nuclear Information System (INIS)

Dutreix, J.; Wambersie, A.

1975-01-01

The shape of the cell survival curve for the cell population relevant to some biological effects has been derived from the comparison of the total doses which result in the same biological effect for two irradiations delivered with N and 2N fractions in the same overall time. They show an initial slope which is interpreted as related to directly lethal, i.e. 'one-hit' or 'irreparable' events. The ratio of the initial slope and the slope at a dose D gives the contribution of the cell killing by directly lethal events relative to cell killing by accumulation of sublethal events. The bioligical effects which have been studied are: (i) dry desquamation of the skin of C 3 H mice and patients; (ii) intestinal death of BALB/c mice; and (iii) lung death of C 3 H mice. The shape of the cell survival curve has been found to be similar for skin desquamation and for intestinal death with a large contribution of lethal events, at single doses of 1000 rad. For lung death the initial tangent has a smaller slope and the shoulder is broader; this is interpreted as a relatively smaller contribution of lethal events with respect to accumulation of sublethal events. (author)

Three dimensions of the survival curve: horizontalization, verticalization, and longevity extension.

Science.gov (United States)

Cheung, Siu Lan Karen; Robine, Jean-Marie; Tu, Edward Jow-Ching; Caselli, Graziella

2005-05-01

Three dimensions of the survival curve have been developed: (1) "horizontalization," which corresponds to how long a cohort and how many survivors can live before aging-related deaths significantly decrease the proportion of survivors; (2) "verticalization," which corresponds to how concentrated aging-related ("normal") deaths are around the modal age at death (M); and (3) "longevity extension," which corresponds to how far the highest normal life durations can exceed M. Our study shows that the degree of horizontalization increased relatively less than the degree of verticalization in Hong Kong from 1976 to 2001. After age normalization, the highest normal life durations moved closer to M, implying that the increase in human longevity is meeting some resistance.

Effect of different heat treatments and disinfectants on the survival of Prototheca zopfii.

Science.gov (United States)

Lassa, Henryka; Jagielski, Tomasz; Malinowski, Edward

2011-03-01

Bovine mastitis caused by the yeast-like alga Prototheca zopfii represents a serious veterinary problem and may result in heavy economic losses to particular dairy farms. The purpose of this study was to evaluate the survival of 50 isolates of P. zopfii in milk subjected to different heat treatments and the survival of further 106 P. zopfii isolates after exposure to three classes of teat disinfectants: iodine (Dipal), quaternary ammonium compounds (Teat), and dodecylbenzenesulphonic acid (Blu-gard). Of the 50 isolates tested for thermal tolerance, 29 (58%) survived heat treatment at 62 °C for 30 s and 13 (26% of all isolates) of those survived after heat treatment at 72 °C for 15 s. None of the 106 isolates were able to withstand the in-use concentrations of the three disinfectants tested. The highest disinfectant concentrations that permitted survival of at least one isolate were dilutions: 1:1,000 for Dipal (survival rate of 52.8-57.5%), 1:100 for Teat (88.7-90.6%), and 1:10 for Blu-gard (100%). No differences in the survival rates of P. zopfii were observed with respect to the duration of exposure to disinfectant. The results of this study support the previous findings that P. zopfii may resist high-temperature treatments, including that applied in the high-temperature, short-time (HTST) pasteurization process. The obtained data also demonstrate the efficacy of the three classes of teat disinfectants against P. zopfii, with the efficacy of iodine being most pronounced. The study emphasizes the necessity of using higher temperatures in the pasteurization of raw milk to kill the Prototheca algae, as well as the particular suitability of the iodine for the control procedures of protothecal mastitis.

Mean inactivation dose: a useful concept for intercomparison of human cell survival curves

International Nuclear Information System (INIS)

Fertil, B.; Dertinger, H.; Courdi, A.; Malaise, E.P.

1984-01-01

The mean inactivation dose (anti D) is calculated for published in vitro survival curves obtained from cell lines of both normal and neoplastic human tissues. Cells belonging to different histological categories (melanomas, carcinomas, etc.) are shown to be characterized by distinct values of anti D which are related to the clinical radiosensitivity of tumors from these categories. Compared to other ways of representing in vitro radiosensitivity, e.g., by the multitarget parameters D 8 and n, the parameter anti D has several specific advantages

Analyzing survival curves at a fixed point in time for paired and clustered right-censored data

Science.gov (United States)

Su, Pei-Fang; Chi, Yunchan; Lee, Chun-Yi; Shyr, Yu; Liao, Yi-De

2018-01-01

In clinical trials, information about certain time points may be of interest in making decisions about treatment effectiveness. Rather than comparing entire survival curves, researchers can focus on the comparison at fixed time points that may have a clinical utility for patients. For two independent samples of right-censored data, Klein et al. (2007) compared survival probabilities at a fixed time point by studying a number of tests based on some transformations of the Kaplan-Meier estimators of the survival function. However, to compare the survival probabilities at a fixed time point for paired right-censored data or clustered right-censored data, their approach would need to be modified. In this paper, we extend the statistics to accommodate the possible within-paired correlation and within-clustered correlation, respectively. We use simulation studies to present comparative results. Finally, we illustrate the implementation of these methods using two real data sets. PMID:29456280

Development of a statistically-based lower bound fracture toughness curve (Ksub(IR) curve)

International Nuclear Information System (INIS)

Wullaert, R.A.; Server, W.L.; Oldfield, W.; Stahlkopf, K.E.

1977-01-01

A program of initiation fracture toughness measurements on fifty heats of nuclear pressure vessel production materials (including weldments) was used to develop a methodology for establishing a revised reference toughness curve. The new methodology was statistically developed and provides a predefined confidence limit (or tolerance limit) for fracture toughness based upon many heats of a particular type of material. Overall reference curves were developed for seven specific materials using large specimen static and dynamic fracture toughness results. The heat-to-heat variation was removed by normalizing both the fracture toughness and temperature data with the precracked Charpy tanh curve coefficients for each particular heat. The variance and distribution about the curve were determined, and lower bounds of predetermined statistical significance were drawn based upon a Pearson distribution in the lower shelf region (since the data were skewed to high values) and a t-distribution in the transition temperature region (since the data were normally distributed)

Numerical Simulation of Heat and Flow Behaviors in Butt-fusion Welding Process of HDPE Pipes with Curved Fusion Surface

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jae Hyun; Ahn, Kyung Hyun [Seoul National University, Seoul (Korea, Republic of); Choi, Sunwoong; Oh, Ju Seok [Hannam University, Daejeon (Korea, Republic of)

2017-08-15

Butt-fusion welding process is used to join the polymeric pipes. Recently, some researchers suggest the curved surface to enhance a welding quality. We investigated how curved welding surface affects heat and flow behaviors of polymer melt during the process in 2D axisymmetric domain with finite element method, and discussed the effect to the welding quality. In this study, we considered HDPE pipes. In heat soak stage, curved phase interface between the melt and solid is shown along the shape of welding surface. In jointing stage, squeezing flow is generated between curved welding surface and phase interface. The low shear rate in fusion domain reduces the alignment of polymer to the perpendicular direction of pipes, and then this phenomenon is expected to help to enhance the welding quality.

A versatile test for equality of two survival functions based on weighted differences of Kaplan-Meier curves.

Science.gov (United States)

Uno, Hajime; Tian, Lu; Claggett, Brian; Wei, L J

2015-12-10

With censored event time observations, the logrank test is the most popular tool for testing the equality of two underlying survival distributions. Although this test is asymptotically distribution free, it may not be powerful when the proportional hazards assumption is violated. Various other novel testing procedures have been proposed, which generally are derived by assuming a class of specific alternative hypotheses with respect to the hazard functions. The test considered by Pepe and Fleming (1989) is based on a linear combination of weighted differences of the two Kaplan-Meier curves over time and is a natural tool to assess the difference of two survival functions directly. In this article, we take a similar approach but choose weights that are proportional to the observed standardized difference of the estimated survival curves at each time point. The new proposal automatically makes weighting adjustments empirically. The new test statistic is aimed at a one-sided general alternative hypothesis and is distributed with a short right tail under the null hypothesis but with a heavy tail under the alternative. The results from extensive numerical studies demonstrate that the new procedure performs well under various general alternatives with a caution of a minor inflation of the type I error rate when the sample size is small or the number of observed events is small. The survival data from a recent cancer comparative study are utilized for illustrating the implementation of the process. Copyright © 2015 John Wiley & Sons, Ltd.

Critical heat flux (CHF) phenomenon on a downward facing curved surface

Energy Technology Data Exchange (ETDEWEB)

Cheung, F.B.; Haddad, K.H.; Liu, Y.C. [Pennsylvania State Univ., University Park, PA (United States). Dept. of Mechanical Engineering

1997-06-01

This report describes a theoretical and experimental study of the boundary layer boiling and critical heat flux phenomena on a downward facing curved heating surface, including both hemispherical and toroidal surfaces. A subscale boundary layer boiling (SBLB) test facility was developed to measure the spatial variation of the critical heat flux and observe the underlying mechanisms. Transient quenching and steady-state boiling experiments were performed in the SBLB facility under both saturated and subcooled conditions to obtain a complete database on the critical heat flux. To complement the experimental effort, an advanced hydrodynamic CHF model was developed from the conservation laws along with sound physical arguments. The model provides a clear physical explanation for the spatial variation of the CHF observed in the SBLB experiments and for the weak dependence of the CHF data on the physical size of the vessel. Based upon the CHF model, a scaling law was established for estimating the local critical heat flux on the outer surface of a heated hemispherical vessel that is fully submerged in water. The scaling law, which compares favorably with all the available local CHF data obtained for various vessel sizes, can be used to predict the local CHF limits on large commercial-size vessels. This technical information represents one of the essential elements that is needed in assessing the efficacy of external cooling of core melt by cavity flooding as a severe accident management strategy. 83 figs., 3 tabs.

Critical heat flux (CHF) phenomenon on a downward facing curved surface

International Nuclear Information System (INIS)

Cheung, F.B.; Haddad, K.H.; Liu, Y.C.

1997-06-01

This report describes a theoretical and experimental study of the boundary layer boiling and critical heat flux phenomena on a downward facing curved heating surface, including both hemispherical and toroidal surfaces. A subscale boundary layer boiling (SBLB) test facility was developed to measure the spatial variation of the critical heat flux and observe the underlying mechanisms. Transient quenching and steady-state boiling experiments were performed in the SBLB facility under both saturated and subcooled conditions to obtain a complete database on the critical heat flux. To complement the experimental effort, an advanced hydrodynamic CHF model was developed from the conservation laws along with sound physical arguments. The model provides a clear physical explanation for the spatial variation of the CHF observed in the SBLB experiments and for the weak dependence of the CHF data on the physical size of the vessel. Based upon the CHF model, a scaling law was established for estimating the local critical heat flux on the outer surface of a heated hemispherical vessel that is fully submerged in water. The scaling law, which compares favorably with all the available local CHF data obtained for various vessel sizes, can be used to predict the local CHF limits on large commercial-size vessels. This technical information represents one of the essential elements that is needed in assessing the efficacy of external cooling of core melt by cavity flooding as a severe accident management strategy. 83 figs., 3 tabs

Reply to comments on-The effect of the heating rate on the characteristics of some experimental thermoluminescence glow curves by Rasheedy et al

International Nuclear Information System (INIS)

Rasheedy, M S; Zahran, E M

2006-01-01

In the paper by Kumar et al, some criticism is advanced to the analysis of the glow curves measured under different heating rates in the laboratory, which appeared in our recent paper [M.S. Rasheedy and E.M. Zahran, 2006 Phys. Scr., 73 98-102]. According to this analysis the area under the glow curve is conserved in both TL-time plots and TL-temperature plots. On the contrary, Kumar et al supposed increase of the area under the glow curve with increasing the heating rate in the case of TL-temperature plots. Since this criticism discredits a physical reason for conservation of the area under the glow curves due to conservation of the imparted dose at different heating rates, a reply appears to be timely

X-ray heating and the optical light curve of HZ Herculis

International Nuclear Information System (INIS)

Perrenod, S.C.; Shields, G.A.

1975-01-01

We discuss theoretically the optical light curve of HZ Her, the binary companion of the pulsed X-ray source Her X-1. Using model stellar atmospheres, we construct light curves that are in agreement with UBV photometry of HZ Her except for the sharpness of the minimum. Unlike previous authors, we find that heating of the photosphere of HZ Her by the observed X-ray flux is sufficient to explain the amplitude of the light variations in each color, if the X-ray emission persists at HZ Her throughout the 35-day ON-OFF CYCLE. We rule out a corona surrounding HZ Her as the source of the extra light near minimum, and we also rule out a model wherein the extra light is caused by a stellar wind that electron-scatters optical light emitted by the photosphere of the hot side of the star

The effect of heat on Na+/H+ antiport function and survival in mammalian cells

International Nuclear Information System (INIS)

Liu, F.-F.; Diep, Kim; Tannock, Ian F.; Hill, Richard P.

1996-01-01

Purpose: Because intracellular pH (pH i ) is a determinant of thermosensitivity, it is important to understand the relationship between heat cytotoxicity and the mechanisms responsible for pH i regulation, such as the Na + /H + antiport. The objective of this study is to elucidate the relationship between heat damage and Na + /H + antiport activity. Methods and Materials: Various cell lines, EMT6, RIF-1, and its thermoresistant variant TR-4, and CCL39, and its variant that lacks the Na + /H + antiport (PS120), were all heated using a water bath. Parallel assessments of antiport function and pH i were made using the fluorescent dye 2,7-biscarboxyethyl-5(6)-carboxyfluorescein (BCECF). Results: Exposure of EMT6 cells to 43-46 deg. C for 30-60 min caused progressive decline in antiport activity, in parallel with cytotoxicity. When the same degree of cytotoxicity was induced by ionizing radiation, no alteration in Na + /H + antiport function was observed. Despite a 10-fold lower survival in RIF-1 compared to TR-4 cells after heating, there was no difference in the thermosensitivity of their antiports. Antiport activity in the TR-4 cells, however, was higher than that of RIF-1 cells both before and during heating. Intracellular pH for TR-4 cells decreased minimally during heating, in contrast to a decline of 1 pH unit in RIF-1 cells despite similar relative levels of antiport activity, suggesting that in this pair of cell lines, antiport activity does not play a major pH i regulatory role. PS120 and CCL39 cells had similar survival levels when heated at pH e 7.2 in the presence of NaHCO 3 , which allows function of the other major regulator of pH i , the Na + -dependent HCO 3 - /Cl - exchanger. This occurred despite a drop in pH i in the PS120 cells during heating. A reduced survival was observed, however, in PS120 cells after 43 deg. C for 30-60 min at either pH e 6.5 or pH e 7.2 in the absence of NaHCO 3 . Intracellular pH for both lines decreased with increasing

Survival curves to support quality improvement in hospitals with excess 30-day mortality after acute myocardial infarction, cerebral stroke and hip fracture: a before-after study.

Science.gov (United States)

Kristoffersen, Doris Tove; Helgeland, Jon; Waage, Halfrid Persdatter; Thalamus, Jacob; Clemens, Dirk; Lindman, Anja Schou; Rygh, Liv Helen; Tjomsland, Ole

2015-03-25

To evaluate survival curves (Kaplan-Meier) as a means of identifying areas in the clinical pathway amenable to quality improvement. Observational before-after study. In Norway, annual public reporting of nationwide 30-day in-and-out-of-hospital mortality (30D) for three medical conditions started in 2011: first time acute myocardial infarction (AMI), stroke and hip fracture; reported for 2009. 12 of 61 hospitals had statistically significant lower/higher mortality compared with the hospital mean. Three hospitals with significantly higher mortality requested detailed analyses for quality improvement purposes: Telemark Hospital Trust Skien (AMI and stroke), Østfold Hospital Trust Fredrikstad (stroke), Innlandet Hospital Trust Gjøvik (hip fracture). Survival curves, crude and risk-adjusted 30D before (2008-2009) and after (2012-2013). Unadjusted survival curves for the outlier hospitals were compared to curves based on pooled data from the other hospitals for the 30-day period 2008-2009. For patients admitted with AMI (Skien), stroke (Fredrikstad) and hip fracture (Gjøvik), the curves suggested increased mortality from the initial part of the clinical pathway. For stroke (Skien), increased mortality appeared after about 8 days. The curve profiles were thought to reflect suboptimal care in various phases in the clinical pathway. This informed improvement efforts. For 2008-2009, hospital-specific curves differed from other hospitals: borderline significant for AMI (p=0.064), highly significant (p≤0.005) for the remainder. After intervention, no difference was found (p>0.188). Before-after comparison of the curves within each hospital revealed a significant change for Fredrikstad (p=0.006). For the three hospitals, crude 30D declined and they were non-outliers for risk-adjusted 30D for 2013. Survival curves as a supplement to 30D may be useful for identifying suboptimal care in the clinical pathway, and thus informing design of quality improvement projects

Combined Effect of Gamma Irradiation and Heat Treatment on Microflora of Spices

Energy Technology Data Exchange (ETDEWEB)

Kiss, I.; Farkas, J. [Central Food Research Institute, Budapest (Hungary)

1981-09-15

The radiation sensitivity of the aerobic bacterial flora was similar both in the ground paprika and the whole black pepper (D{sub 10} values calculated from the exponential survival curves were 1.44 and 1.29 kGy, respectively). The survival rates of the microflora of non-irradiated samples were compared with those of the 1.6-4 kGy irradiated samples as a function of the heating time at various temperature levels, applied to aqueous suspensions of spices. The mesophilic aerobic bacterial flora of black pepper proved to be more heat-resistant than that of paprika powder. The heat resistance of the surviving microflora of irradiated spices was significantly decreased. The heat sensitization effect tended to increase as the radiation dose increased. The heat sensitization by irradiation was greater in the case of the more heat resistant microflora of black pepper. The heat sensitization quotient at 90 Degree-Sign C (i.e. the ratio of the 90% destruction time for unirradiated versus irradiated samples) was approximately 4 for paprika and 9 for black pepper at the 4-kGy dose level. (author)

Combined effect of gamma irradiation and heat treatment on microflora of spices

International Nuclear Information System (INIS)

Kiss, I.; Farkas, J.

1981-01-01

The radiation sensitivity of the aerobic bacterial flora was similar both in the ground paprika and the whole black pepper (D 10 values calculated from the exponential survival curves were 1.44 and 1.29 kGy, respectively). The survival rates of the microflora of non-irradiated samples were compared with those of the 1.6-4 kGy irradiated samples as a function of the heating time at various temperature levels, applied to aqueous suspensions of spices. The mesophilic aerobic bacterial flora of black pepper proved to be more heat-resistant than that of paprika powder. The heat resistance of the surviving microflora of irradiated spices was significantly decreased. The heat sensitization effect tended to increase as the radiation dose increased. The heat sensitization by irradiation was greater in the case of the more heat-resistant microflora of black pepper. The heat sensitization quotient at 90 0 C (i.e. the ratio of the 90% destruction time for unirradiated versus irradiated samples) was approximately 4 for paprika and 9 for black pepper at the 4-kGy dose level. (author)

Numerical study for Darcy-Forchheimer flow due to a curved stretching surface with Cattaneo-Christov heat flux and homogeneous-heterogeneous reactions

Directory of Open Access Journals (Sweden)

Tasawar Hayat

Full Text Available The current investigation presents Darcy-Forchheimer flow of viscous fluid caused by a curved stretching sheet. Flow for porous space is characterized by Darcy-Forchheimer relation. Concept of homogeneous and heterogeneous reactions is also utilized. Heat transfer for Cattaneo–Christov theory characterizing the feature of thermal relaxation is incorporated. Nonlinear differential systems are derived. Shooting algorithm is employed to construct the solutions for the resulting nonlinear system. The characteristics of various sundry parameters are studied and discussed. Skin friction coefficient and heat transfer rate are numerically described. Keywords: 2D flow, Curved stretching surface, Darcy-Forchheimer porous medium, Cattaneo-Christov heat flux, Homogeneous-heterogeneous reactions

Initial slope of human tumor cell survival curves: its modification by the oxic cell sensitizer beta-arabinofuranosyladenine

International Nuclear Information System (INIS)

Chavaudra, N.; Halimi, M.; Parmentier, C.; Gaillard, N.; Grinfeld, S.; Malaise, E.P.

1989-01-01

The initial slope of the survival curve, which is a characteristic of each tumor cell line, varies with the histological group of the tumor. It is one of the factors on which clinical radioresponsiveness depends. The DNA dependant DNA polymerase inhibitor beta-ara A acts as an oxic cell sensitizer. This study was carried out on human tumor cell lines to look for a correlation between the degree of radiosensitization induced by beta-ara A and the radiosensitivity of a given cell line. Six human tumor cell lines with different radiosensitivities were used (the survival rate at 2 Gy and D ranged from 20 to 73% and from 1.2 to 3.2 Gy, respectively). beta-ara A had a major toxic effect on all cell lines but this varied greatly from one cell line to another and was concentration dependant; this toxic effect was taken into account when calculating the surviving fractions. For all cell lines, beta-ara A acted as an oxic radiosensitizer and the radiosensitization was concentration dependant. Analysis of the survival curves of the 6 cell lines using the linear quadratic model showed that concentrations of beta-ara A between 200 and 1000 microM induced an increase in the linear component while the quadratic component underwent no systematic change. The sensitizing enhancement ratio (SER) measured from the Ds ratios, varied greatly from one line to another. For example, at a concentration of 500 microM, the extreme values of Ds ratios were 1.5 and 2.6. The radiosensitization is greater, the higher the radiosensitivity of the cell line studied during exponential growth. The results do not favor the use of beta-ara A in the treatment of intrinsically radioresistant human tumors

Initial slope of human tumor cell survival curves: its modification by the oxic cell sensitizer beta-arabinofuranosyladenine

Energy Technology Data Exchange (ETDEWEB)

Chavaudra, N.; Halimi, M.; Parmentier, C.; Gaillard, N.; Grinfeld, S.; Malaise, E.P.

1989-05-01

The initial slope of the survival curve, which is a characteristic of each tumor cell line, varies with the histological group of the tumor. It is one of the factors on which clinical radioresponsiveness depends. The DNA dependant DNA polymerase inhibitor beta-ara A acts as an oxic cell sensitizer. This study was carried out on human tumor cell lines to look for a correlation between the degree of radiosensitization induced by beta-ara A and the radiosensitivity of a given cell line. Six human tumor cell lines with different radiosensitivities were used (the survival rate at 2 Gy and D ranged from 20 to 73% and from 1.2 to 3.2 Gy, respectively). beta-ara A had a major toxic effect on all cell lines but this varied greatly from one cell line to another and was concentration dependant; this toxic effect was taken into account when calculating the surviving fractions. For all cell lines, beta-ara A acted as an oxic radiosensitizer and the radiosensitization was concentration dependant. Analysis of the survival curves of the 6 cell lines using the linear quadratic model showed that concentrations of beta-ara A between 200 and 1000 microM induced an increase in the linear component while the quadratic component underwent no systematic change. The sensitizing enhancement ratio (SER) measured from the Ds ratios, varied greatly from one line to another. For example, at a concentration of 500 microM, the extreme values of Ds ratios were 1.5 and 2.6. The radiosensitization is greater, the higher the radiosensitivity of the cell line studied during exponential growth. The results do not favor the use of beta-ara A in the treatment of intrinsically radioresistant human tumors.

MTD-MFC: unified framework for investigation of diversity of boiling heat transfer curves

Energy Technology Data Exchange (ETDEWEB)

Shekriladze, I.G. [Georgian Technical University, Tbilisi (Georgia)], e-mail: shekri@geo.net.ge

2009-07-01

A keynote paper presents just the next attempt to promote a discussion of modern state of art in the field of boiling heat transfer research. It is shown how longstanding disregard of internal contradictions of applicable approaches has resulted theoretical deadlock. Alternatively, it also is shown how resolution of these contradictions opens the ways to breakthrough in boiling heat transfer theory. Basic experimental facts, physical models and correlations are reconsidered. Principal contradictions between experimental knowledge and traditional model of 'the theatre of actors' (MTA) are discussed. Crucial role of pumping effect of growing bubble (PEGB) in boiling heat transfer and hydrodynamics is shown. Basic role of control of HTC by thermodynamic conditions on nucleation sites is demonstrated and consequent model of 'the theatre of director' (MTD) is discussed. Universal MTD-based correlation of boiling HTC of all types of liquids is considered. Unified consistent research framework for developed boiling heat transfer and diverse specific boiling heat transfer regimes is outlined through supplementing MTD by so-called multifactoring concept (MFC). The latter links transition from developed boiling mode to diverse boiling curves to a phenomenon of multiplication of factors influencing HTC. The ways of further research of the boiling problem are discussed. (author)

MTD-MFC: unified framework for investigation of diversity of boiling heat transfer curves

International Nuclear Information System (INIS)

Shekriladze, I.G.

2009-01-01

A keynote paper presents just the next attempt to promote a discussion of modern state of art in the field of boiling heat transfer research. It is shown how longstanding disregard of internal contradictions of applicable approaches has resulted theoretical deadlock. Alternatively, it also is shown how resolution of these contradictions opens the ways to breakthrough in boiling heat transfer theory. Basic experimental facts, physical models and correlations are reconsidered. Principal contradictions between experimental knowledge and traditional model of 'the theatre of actors' (MTA) are discussed. Crucial role of pumping effect of growing bubble (PEGB) in boiling heat transfer and hydrodynamics is shown. Basic role of control of HTC by thermodynamic conditions on nucleation sites is demonstrated and consequent model of 'the theatre of director' (MTD) is discussed. Universal MTD-based correlation of boiling HTC of all types of liquids is considered. Unified consistent research framework for developed boiling heat transfer and diverse specific boiling heat transfer regimes is outlined through supplementing MTD by so-called multifactoring concept (MFC). The latter links transition from developed boiling mode to diverse boiling curves to a phenomenon of multiplication of factors influencing HTC. The ways of further research of the boiling problem are discussed. (author)

The Heating Curve Adjustment Method

NARCIS (Netherlands)

Kornaat, W.; Peitsman, H.C.

1995-01-01

In apartment buildings with a collective heating system usually a weather compensator is used for controlling the heat delivery to the various apartments. With this weather compensator the supply water temperature to the apartments is regulated depending on the outside air temperature. With

An analytic model of pool boiling critical heat flux on an immerged downward facing curved surface

International Nuclear Information System (INIS)

He, Hui; Pan, Liang-ming; Wu, Yao; Chen, De-qi

2015-01-01

Highlights: • Thin liquid film and supplement of liquid contribute to the CHF. • CHF increases from the bottom to the upper of the lowerhead. • Evaporation of thin liquid film is dominant nearby bottom region. • The subcooling has significant effects on the CHF. - Abstract: In this paper, an analytical model of the critical heat flux (CHF) on the downward facing curved surface for pool boiling has been proposed, which hypothesizes that the CHF on the downward facing curved is composed of two parts, i.e. the evaporation of the thin liquid film underneath the elongated bubble adhering to the lower head outer surface and the depletion of supplement of liquid due to the relative motion of vapor bubbles along with the downward facing curved. The former adopts the Kelvin–Helmholtz instability analysis of vapor–liquid interface of the vapor jets which penetrating in the thin liquid film. When the heat flux closing to the CHF point, the vapor–liquid interface becomes highly distorted, which block liquid to feed the thin liquid film and the thin liquid film will dry out gradually. While the latter considers that the vapor bubbles move along with the downward facing curved surface, and the liquid in two-phase boundary layer enter the liquid film that will be exhausted when the CHF occurs. Based on the aforementioned mechanism and the energy balance between the thin liquid film evaporation and water feeding, and taking the subcooling of the bulk water into account, the mathematic model about the downward facing curved surface CHF has been proposed. The CHF of the downward facing curved surface for pool boiling increases along with the downward facing orientation except in the vicinity of bottom center region, because in this region the vapor bubble almost stagnates and the evaporation of the thin liquid film is dominant. In addition, the subcooling has significant effect on the CHF. Comparing the result of this model with the published experimental results show

Implications of the quadratic cell survival curve and human skin radiation ''tolerance doses'' on fractionation and superfractionation dose selection

International Nuclear Information System (INIS)

Douglas, B.G.

1982-01-01

An analysis of early published multifraction orthovoltage human acute skin irradiation tolerance isoeffect doses is presented. It indicates that human acute skin radiation reactions may result from the repetition, with each dose fraction, of a cell survival curve of the form: S = e/sup -(αD + βD 2 )/). The analysis also shows no need for an independent proliferation related time factor for skin, for daily treatments of six weeks or less in duration. The value obtained for the constant β/α for orthovoltage irradiation from these data is 2.9 x 10 -3 rad -1 for the cell line determining acute skin tolerance. A radiation isoeffect relationship, based on the quadratic cell survival curve, is introduced for human skin. This relationship has some advantages over the nominal standard dose (NSD). First, its use is not restricted to tolerance level reactions. Second, a modification of the relationship, which is also introduced, may be employed in the selection of doses per treatment when irradiation dose fractions are administered at short intervals where repair of sublethal injury is incomplete

Unsteady laminar flow with convective heat transfer through a rotating curved square duct with small curvature

Energy Technology Data Exchange (ETDEWEB)

Mondal, Rabindra Nath, E-mail: rnmondal71@yahoo.com; Shaha, Poly Rani [Department of Mathematics, Jagannath University, Dhaka-1100 (Bangladesh); Roy, Titob [Department of Mathematics, Vikarunnesa Nun School and College, Boshundhara, Dhaka (Bangladesh); Yanase, Shinichiro, E-mail: yanase@okayama-u.ac.jp [Department of Mechanical and Systems Engineering, Okayama University, Okayama 700-8530 (Japan)

2016-07-12

Unsteady laminar flow with convective heat transfer through a curved square duct rotating at a constant angular velocity about the center of curvature is investigated numerically by using a spectral method, and covering a wide range of the Taylor number −300≤Tr≤1000 for the Dean number Dn = 1000. A temperature difference is applied across the vertical sidewalls for the Grashof number Gr = 100, where the outer wall is heated and the inner wall cooled, the top and bottom walls being adiabatic. Flow characteristics are investigated with the effects of rotational parameter, Tr, and the pressure-driven parameter, Dn, for the constant curvature 0.001. Time evolution calculations as well as their phase spaces show that the unsteady flow undergoes through various flow instabilities in the scenario ‘multi-periodic → chaotic → steady-state → periodic → multi-periodic → chaotic’, if Tr is increased in the positive direction. For negative rotation, however, time evolution calculations show that the flow undergoes in the scenario ‘multi-periodic → periodic → steady-state’, if Tr is increased in the negative direction. Typical contours of secondary flow patterns and temperature profiles are obtained at several values of Tr, and it is found that the unsteady flow consists of two- to six-vortex solutions if the duct rotation is involved. External heating is shown to generate a significant temperature gradient at the outer wall of the duct. This study also shows that there is a strong interaction between the heating-induced buoyancy force and the centrifugal-Coriolis instability in the curved channel that stimulates fluid mixing and consequently enhances heat transfer in the fluid.

Decreased survival of prostate cancer cells in vitro by combined treatment of heat and an antioxidant inhibitor diethyldithiocarbamate (DDC).

Science.gov (United States)

Moriyama-Gonda, Nobuko; Igawa, Mikio; Shiina, Hiroaki; Urakami, Shinji; Terashima, Masaharu

2003-11-01

The aim of this study was to examine a modulation of thermotolerance by treatment with combination of heat and the antioxidant inhibitor diethyldithiocarbamate (DDC) of the PC-3 prostate cancer cells. To determine thermotolerance, cells were heated once or twice. Two 1 h exposures at 43 degrees C, with a recovery period in between, revealed better survival/recovery of cells after the second exposure than after the first (fig. 1A + 1B). Additional experiments were performed, heating cells twice (fig. 1B + 1C). First, cells were heated at 43 degrees C for 1 h and, after various recovery times (intervals) at 37 degree C, subsequently reheated at 44 degrees C for 1 h. To ensure effective cell killing, efficiency of the combined treatments of 1 mM DDC and heating at 43 or 44 degrees C for 1 h was estimated by measuring cell survival, reactive oxygen species (ROS) generation, superoxide dismutase (SOD) activity and heat shock protein 70 (hsp 70) expression. To obtain a more effective method for subsequent heat exposure, cells were heated twice after a 24 h interval in the presence or absence of 1 mM DDC. ROS generation and SOD activity immediately increased correlating with duration of heating, but their levels gently decreased with time after discontinuation of heating. On the other hand, hsp 70 levels slowly increased, also correlating with duration of heating but continued to increase with time after discontinuation of heating for a certain period. DDC administration coupled with heating at 43 or 44 degrees C significantly decreased cell survival compared to heating alone (p DDC as compared to heat alone at 43 and 44 degrees C (p DDC could have potential benefits in the treatment of prostate cancer.

Various Wolbachia genotypes differently influence host Drosophila dopamine metabolism and survival under heat stress conditions.

Science.gov (United States)

Gruntenko, Nataly Е; Ilinsky, Yury Yu; Adonyeva, Natalya V; Burdina, Elena V; Bykov, Roman A; Menshanov, Petr N; Rauschenbach, Inga Yu

2017-12-28

One of the most widespread prokaryotic symbionts of invertebrates is the intracellular bacteria of Wolbachia genus which can be found in about 50% of insect species. Wolbachia causes both parasitic and mutualistic effects on its host that include manipulating the host reproductive systems in order to increase their transmission through the female germline, and increasing the host fitness. One of the mechanisms, promoting adaptation in biological organisms, is a non-specific neuroendocrine stress reaction. In insects, this reaction includes catecholamines, dopamine, serotonin and octopamine, which act as neurotransmitters, neuromodulators and neurohormones. The level of dopamine metabolism correlates with heat stress resistance in Drosophila adults. To examine Wolbachia effect on Drosophila survival under heat stress and dopamine metabolism we used five strains carrying the nuclear background of interbred Bi90 strain and cytoplasmic backgrounds with different genotype variants of Wolbachia (produced by 20 backcrosses of Bi90 males with appropriate source of Wolbachia). Non-infected Bi90 strain (treated with tetracycline for 3 generations) was used as a control group. We demonstrated that two of five investigated Wolbachia variants promote changes in Drosophila heat stress resistance and activity of enzymes that produce and degrade dopamine, alkaline phosphatase and dopamine-dependent arylalkylamine N-acetyltransferase. What is especially interesting, wMelCS genotype of Wolbachia increases stress resistance and the intensity of dopamine metabolism, whereas wMelPop strain decreases them. wMel, wMel2 and wMel4 genotypes of Wolbachia do not show any effect on the survival under heat stress or dopamine metabolism. L-DOPA treatment, known to increase the dopamine content in Drosophila, levels the difference in survival under heat stress between all studied groups. The genotype of symbiont determines the effect that the symbiont has on the stress resistance of the host

Thermal protection from a finite period of heat exposure – Heat survival of flight data recorders

International Nuclear Information System (INIS)

Rana, Ruhul Amin; Li, Ri

2015-01-01

This work relates to developing thermal protection for a finite period of exposure to a high temperature environment. This type of transient heat transfer problem starts with a heating period, which is then followed by a cooling period once the high temperature environment disappears. The study is particularly relevant to the thermal protection of flight data recorders from high temperature flame. In this work, transient heat conduction through a three-concentric-layer configuration is numerically studied, which includes a metal housing, a thermal insulation, and a phase change material. The thermal performance is evaluated using the center temperature changing with time. It is found that the center temperature reaches a peak during cooling period rather than heating period. Time taken to reach the peak and the peak value depend on the sizes and properties of the layers. The properties include latent heat of fusion, melting temperature, heat capacities, and thermal conductivities. Parametric study is conducted to analyze and distinguish the influence of these parameters. The study provides general guidance for determining sizes and selecting materials for the thermal design of flight data recorders. Additionally, the study is also useful for other similar applications, for which thermal management and protection over a period of time is needed. In this paper, analysis starts with a baseline configuration composed of specific materials and sizes. Finite changes are applied to sizes, properties of the materials, and the results are compared to understand the roles of the varied parameters in affecting the thermal protection performance. - Highlights: • We study the thermal design of flight data recorders for heat survival. • Consecutive heating and cooling of 3-layer configuration is investigated. • Influences of sizes and material properties on thermal protection are explored

Extended analysis of cooling curves

International Nuclear Information System (INIS)

Djurdjevic, M.B.; Kierkus, W.T.; Liliac, R.E.; Sokolowski, J.H.

2002-01-01

Thermal Analysis (TA) is the measurement of changes in a physical property of a material that is heated through a phase transformation temperature range. The temperature changes in the material are recorded as a function of the heating or cooling time in such a manner that allows for the detection of phase transformations. In order to increase accuracy, characteristic points on the cooling curve have been identified using the first derivative curve plotted versus time. In this paper, an alternative approach to the analysis of the cooling curve has been proposed. The first derivative curve has been plotted versus temperature and all characteristic points have been identified with the same accuracy achieved using the traditional method. The new cooling curve analysis also enables the Dendrite Coherency Point (DCP) to be detected using only one thermocouple. (author)

Comparing survival curves using rank tests

NARCIS (Netherlands)

Albers, Willem/Wim

1990-01-01

Survival times of patients can be compared using rank tests in various experimental setups, including the two-sample case and the case of paired data. Attention is focussed on two frequently occurring complications in medical applications: censoring and tail alternatives. A review is given of the

Hyperthermic survival of Chinese hamster ovary cells as a function of cellular population density at the time of plating

International Nuclear Information System (INIS)

Highfield, D.P.; Holahan, E.V.; Holahan, P.K.; Dewey, W.C.

1984-01-01

The survival of synchronous G 1 or asynchronous Chinese hamster ovary cells in vitro to heat treatment may depend on the cellular population density at the time of heating and/or as the cells are cultured after heating. The addition of lethally irradiated feeder cells may increase survival at 10 -3 by as much as 10- to 100-fold for a variety of conditions when cells are heated either in suspension culture or as monolayers with or without trypsinization. The protective effect associated with feeder cells appears to be associated with close cell-to-cell proximity. However, when cells are heated without trypsinization about 24 hr or later after plating, when adaptation to monolayer has occurred, the protective effect is reduced; i.e., addition of feeder cells enhances survival much less, for example, about 2- to 3-fold at 10 -2 -10 -3 survival. Also, the survival of a cell to heat is independent of whether the neighboring cell in a microcolony is destined to live or die. Finally, if protective effects associated with cell density do occur and are not controlled, serious artifacts can result as the interaction of heat and radiation is studied; for example, survival curves can be moved upward, and thus changed in shape as the number of cells plated is increased with an increase in the hyperthermic treatment or radiation dose following hyperthermia. Therefore, to understand mechanisms and to obtain information relevant to populations of cells in close proximity, such as those in vivo, these cellular population density effects should be considered and understood

Heat shock proteins and survival strategies in congeneric land snails (Sphincterochila) from different habitats.

Science.gov (United States)

Mizrahi, Tal; Heller, Joseph; Goldenberg, Shoshana; Arad, Zeev

2012-09-01

Polmunate land snails are subject to stress conditions in their terrestrial habitat, and depend on a range of behavioural, physiological and biochemical adaptations for coping with problems of maintaining water, ionic and thermal balance. The involvement of the heat shock protein (HSP) machinery in land snails was demonstrated following short-term experimental aestivation and heat stress, suggesting that land snails use HSPs as part of their survival strategy. As climatic variation was found to be associated with HSP expression, we tested whether adaptation of land snails to different habitats affects HSP expression in two closely related Sphincterochila snail species, a desert species Sphincterochila zonata and a Mediterranean-type species Sphincterochila cariosa. Our study suggests that Sphincterochila species use HSPs as part of their survival strategy following desiccation and heat stress, and as part of the natural annual cycle of activity and aestivation. Our studies also indicate that adaptation to different habitats results in the development of distinct strategies of HSP expression in response to stress, namely the reduced expression of HSPs in the desert-inhabiting species. We suggest that these different strategies reflect the difference in heat and aridity encountered in the natural habitats, and that the desert species S. zonata relies on mechanisms and adaptations other than HSP induction thus avoiding the fitness consequences of continuous HSP upregulation.

Heat Stress-Induced PI3K/mTORC2-Dependent AKT Signaling Is a Central Mediator of Hepatocellular Carcinoma Survival to Thermal Ablation Induced Heat Stress.

Directory of Open Access Journals (Sweden)

Scott M Thompson

Full Text Available Thermal ablative therapies are important treatment options in the multidisciplinary care of patients with hepatocellular carcinoma (HCC, but lesions larger than 2-3 cm are plagued with high local recurrence rates and overall survival of these patients remains poor. Currently no adjuvant therapies exist to prevent local HCC recurrence in patients undergoing thermal ablation. The molecular mechanisms mediating HCC resistance to thermal ablation induced heat stress and local recurrence remain unclear. Here we demonstrate that the HCC cells with a poor prognostic hepatic stem cell subtype (Subtype HS are more resistant to heat stress than HCC cells with a better prognostic hepatocyte subtype (Subtype HC. Moreover, sublethal heat stress rapidly induces phosphoinositide 3-kinase (PI3K/mammalian target of rapamycin (mTOR dependent-protein kinase B (AKT survival signaling in HCC cells in vitro and at the tumor ablation margin in vivo. Conversely, inhibition of PI3K/mTOR complex 2 (mTORC2-dependent AKT phosphorylation or direct inhibition of AKT function both enhance HCC cell killing and decrease HCC cell survival to sublethal heat stress in both poor and better prognostic HCC subtypes while mTOR complex 1 (mTORC1-inhibition has no impact. Finally, we showed that AKT isoforms 1, 2 and 3 are differentially upregulated in primary human HCCs and that overexpression of AKT correlates with worse tumor biology and pathologic features (AKT3 and prognosis (AKT1. Together these findings define a novel molecular mechanism whereby heat stress induces PI3K/mTORC2-dependent AKT survival signaling in HCC cells and provide a mechanistic rationale for adjuvant AKT inhibition in combination with thermal ablation as a strategy to enhance HCC cell killing and prevent local recurrence, particularly at the ablation margin.

Distortion of absorption-line velocity curves due to x-ray heating in x-ray binaries

International Nuclear Information System (INIS)

Milgrom, M.

1976-01-01

The effects of X-ray heating on the measured absorption line velocities, in X-ray binaries with low X-rays to optical luminosities ratio are considered. These effects may be appreciable even for such binaries where the effect of X-ray heating on the light-curve is negligible. The effects are studied qualitatively and suggest possible ways to partially eliminate the systematic errors introduced by them. The individual systems Cyg x-1 and SMC x-1 are treated and the results of numerical calculations are presented for them. For Cyg x-1 it is found that the effect is detectable during the X-ray 'high' state in all regions of the spectrum. During the 'low' state it may be important in the red region of the spectrum. The results for the case in which soft X-ray fluxes (E < or approximately .4 keV, suggested by theoretical models) are present are also given. For SMC x-1 a strong effect for Hα, Hβ, Hγ had been found. This effect may be responsible for the observed variable velocity curve. We also find for SMC x-1 that the average X-ray intensity falling on the primary must be considerably smaller than what is derived from the detected flux, or else the effect is too large. (author)

A review and comparison of methods for recreating individual patient data from published Kaplan-Meier survival curves for economic evaluations: a simulation study.

Science.gov (United States)

Wan, Xiaomin; Peng, Liubao; Li, Yuanjian

2015-01-01

In general, the individual patient-level data (IPD) collected in clinical trials are not available to independent researchers to conduct economic evaluations; researchers only have access to published survival curves and summary statistics. Thus, methods that use published survival curves and summary statistics to reproduce statistics for economic evaluations are essential. Four methods have been identified: two traditional methods 1) least squares method, 2) graphical method; and two recently proposed methods by 3) Hoyle and Henley, 4) Guyot et al. The four methods were first individually reviewed and subsequently assessed regarding their abilities to estimate mean survival through a simulation study. A number of different scenarios were developed that comprised combinations of various sample sizes, censoring rates and parametric survival distributions. One thousand simulated survival datasets were generated for each scenario, and all methods were applied to actual IPD. The uncertainty in the estimate of mean survival time was also captured. All methods provided accurate estimates of the mean survival time when the sample size was 500 and a Weibull distribution was used. When the sample size was 100 and the Weibull distribution was used, the Guyot et al. method was almost as accurate as the Hoyle and Henley method; however, more biases were identified in the traditional methods. When a lognormal distribution was used, the Guyot et al. method generated noticeably less bias and a more accurate uncertainty compared with the Hoyle and Henley method. The traditional methods should not be preferred because of their remarkable overestimation. When the Weibull distribution was used for a fitted model, the Guyot et al. method was almost as accurate as the Hoyle and Henley method. However, if the lognormal distribution was used, the Guyot et al. method was less biased compared with the Hoyle and Henley method.

Heat resistance of thermoduric enterococci isolated from milk.

Science.gov (United States)

McAuley, Catherine M; Gobius, Kari S; Britz, Margaret L; Craven, Heather M

2012-03-15

Enterococci are reported to survive pasteurisation but the extent of their survival is unclear. Sixty-one thermoduric enterococci isolates were selected from laboratory pasteurised milk obtained from silos in six dairy factories. The isolates were screened to determine log(10) reductions incurred after pasteurisation (63°C/30 min) and ranked from highest to lowest log(10) reduction. Two isolates each of Enterococcus faecalis, Enterococcus faecium, Enterococcus durans and Enterococcus hirae, exhibiting the median and the greatest heat resistance, as well as E. faecalis ATCC 19433, were selected for further heat resistance determinations using an immersed coil apparatus. D values were calculated from survival curves plotted from viable counts obtained after heating isolates in Brain Heart Infusion Broth at 63, 69, 72, 75 and 78°C followed by rapid cooling. At 72°C, the temperature employed for High Temperature Short Time (HTST) pasteurisation (72°C/15s), the D values extended from 0.3 min to 5.1 min, depending on the isolate and species. These data were used to calculate z values, which ranged from 5.0 to 9.8°C. The most heat sensitive isolates were E. faecalis (z values 5.0, 5.7 and 7.5°C), while the most heat resistant isolates were E. durans (z values 8.7 and 8.8°C), E. faecium (z value 9.0°C) and E. hirae (z values 8.5 and 9.8°C). The data show that heat resistance in enterococci is highly variable. Copyright © 2011 Elsevier B.V. All rights reserved.

Critical behavior of binary mixture of {(1 − x) C6H5CN + x CH3(CH2)9CH3}: Measurements of coexistence curves, turbidity, and heat capacity

International Nuclear Information System (INIS)

Yin Tianxiang; Lei Yuntao; Mao Chunfeng; Chen Zhiyun; An Xueqin; Shen Weiguo

2012-01-01

Highlights: ► Coexistence curve, isobaric heat capacity and turbidity measurements have been reported. ► Asymmetry of the coexistence curves has been analyzed by the complete scaling theory. ► Heat capacity has been shown to be important in describing the asymmetric criticality. ► Universal amplitude ratios have been tested. - Abstract: (Liquid + liquid) coexistence curve, turbidity, and isobaric heat capacity per unit volume for the critical solution of {benzonitrile + n-undecane} have been measured. The critical exponents β, ν, γ, and α have been deduced, which were found to be consistent with the theoretic predictions. Meanwhile, the experimental data have also been analyzed to obtain the system-dependent critical amplitudes B, ξ 0 , χ 0 , A ± , and D corresponding to the difference of the general density variable of two coexisting phases Δρ, the correlation length ξ, the osmotic compressibility χ, the isobaric heat capacity per unit volume C p V −1 , and the first term of correction-to-scaling for the isobaric heat capacity per unit volume, which were used to test some universal ratios. It was found that the coexistence curve may be well described by the crossover model proposed by Gutkowski et al. The critical-fluctuation induced contribution to the background heat capacity B cr was obtained and used to analyze the asymmetric behavior of the diameter of the coexistence curve. The result indicated that the asymmetry of the coexistence curve can be well described by the complete scaling theory proposed by Anisimov et al., and the heat capacity does make a significant contribution to this asymmetric behavior.

Immuno-oncology combinations: raising the tail of the survival curve

International Nuclear Information System (INIS)

Harris, Samuel J.; Brown, Jessica; Lopez, Juanita; Yap, Timothy A.

2016-01-01

There have been exponential gains in immuno-oncology in recent times through the development of immune checkpoint inhibitors. Already approved by the U.S. Food and Drug Administration for advanced melanoma and non-small cell lung cancer, immune checkpoint inhibitors also appear to have significant antitumor activity in multiple other tumor types. An exciting component of immunotherapy is the durability of antitumor responses observed, with some patients achieving disease control for many years. Nevertheless, not all patients benefit, and efforts should thus now focus on improving the efficacy of immunotherapy through the use of combination approaches and predictive biomarkers of response and resistance. There are multiple potential rational combinations using an immunotherapy backbone, including existing treatments such as radiotherapy, chemotherapy or molecularly targeted agents, as well as other immunotherapeutics. The aim of such antitumor strategies will be to raise the tail on the survival curve by increasing the number of long term survivors, while managing any additive or synergistic toxicities that may arise with immunotherapy combinations. Rational trial designs based on a clear understanding of tumor biology and drug pharmacology remain paramount. This article reviews the biology underpinning immuno-oncology, discusses existing and novel immunotherapeutic combinations currently in development, the challenges of predictive biomarkers of response and resistance and the impact of immuno-oncology on early phase clinical trial design

Heat-killed Lactobacillus spp. cells enhance survivals of Caenorhabditis elegans against Salmonella and Yersinia infections.

Science.gov (United States)

Lee, J; Choe, J; Kim, J; Oh, S; Park, S; Kim, S; Kim, Y

2015-12-01

This study examined the effect of feeding heat-killed Lactobacillus cells on the survival of Caenorhabditis elegans nematodes after Salmonella Typhimurium and Yersinia enterocolitica infection. The feeding of heat-killed Lactobacillus plantarum 133 (LP133) and Lactobacillus fermentum 21 (LP21) cells to nematodes was shown to significantly increase the survival rate as well as stimulate the expression of pmk-1 gene that key factor for C. elegans immunity upon infection compared with control nematodes that were only fed Escherichia coli OP50 (OP50) cells. These results suggest that heat-killed LP133 and LF21 cells exert preventive or protective effects against the Gram-negative bacteria Salm. Typhimurium and Y. enterocolitica. To better understand the mechanisms underlying the LF21-mediated and LP133-mediated protection against bacterial infection in nematodes, transcriptional profiling was performed for each experimental group. These experiments showed that genes related to energy generation and ageing, regulators of insulin/IGF-1-like signalling, DAF genes, oxidation and reduction processes, the defence response and/or the innate immune response, and neurological processes were upregulated in nematodes that had been fed heat-killed Lactobacillus cells compared with nematodes that had been fed E. coli cells. In this study, the feeding of heat-killed Lactobacillus bacteria to Caenorhabditis elegans nematodes was shown to decrease infection by Gram-negative bacteria and increase the host lifespan. C. elegans has a small, well-organized genome and is an excellent in vivo model organism; thus, these results will potentially shed light on important Lactobacillus-host interactions. © 2015 The Society for Applied Microbiology.

First results of saturation curve measurements of heat-resistant steel using GEANT4 and MCNP5 codes

International Nuclear Information System (INIS)

Hoang, Duc-Tam; Tran, Thien-Thanh; Le, Bao-Tran; Vo, Hoang-Nguyen; Chau, Van-Tao; Tran, Kim-Tuyet; Huynh, Dinh-Chuong

2015-01-01

A gamma backscattering technique is applied to calculate the saturation curve and the effective mass attenuation coefficient of material. A NaI(Tl) detector collimated by collimator of large diameter is modeled by Monte Carlo technique using both MCNP5 and GEANT4 codes. The result shows a good agreement in response function of the scattering spectra for the two codes. Based on such spectra, the saturation curve of heat-resistant steel is determined. The results represent a strong confirmation that it is appropriate to use the detector collimator of large diameter to obtain the scattering spectra and this work is also the basis of experimental set-up for determining the thickness of material. (author)

Survival rate and expression of Heat-shock protein 70 and Frost genes after temperature stress in Drosophila melanogaster lines that are selected for recovery time from temperature coma.

Science.gov (United States)

Udaka, Hiroko; Ueda, Chiaki; Goto, Shin G

2010-12-01

In this study, we investigated the physiological mechanisms underlying temperature tolerance using Drosophila melanogaster lines with rapid, intermediate, or slow recovery from heat or chill coma that were established by artificial selection or by free recombination without selection. Specifically, we focused on the relationships among their recovery from heat or chill coma, survival after severe heat or cold, and survival enhanced by rapid cold hardening (RCH) or heat hardening. The recovery time from heat coma was not related to the survival rate after severe heat. The line with rapid recovery from chill coma showed a higher survival rate after severe cold exposure, and therefore the same mechanisms are likely to underlie these phenotypes. The recovery time from chill coma and survival rate after severe cold were unrelated to RCH-enhanced survival. We also examined the expression of two genes, Heat-shock protein 70 (Hsp70) and Frost, in these lines to understand the contribution of these stress-inducible genes to intraspecific variation in recovery from temperature coma. The line showing rapid recovery from heat coma did not exhibit higher expression of Hsp70 and Frost. In addition, Hsp70 and Frost transcription levels were not correlated with the recovery time from chill coma. Thus, Hsp70 and Frost transcriptional regulation was not involved in the intraspecific variation in recovery from temperature coma. Copyright © 2010 Elsevier Ltd. All rights reserved.

Does my high blood pressure improve your survival? Overall and subgroup learning curves in health.

Science.gov (United States)

Van Gestel, Raf; Müller, Tobias; Bosmans, Johan

2017-09-01

Learning curves in health are of interest for a wide range of medical disciplines, healthcare providers, and policy makers. In this paper, we distinguish between three types of learning when identifying overall learning curves: economies of scale, learning from cumulative experience, and human capital depreciation. In addition, we approach the question of how treating more patients with specific characteristics predicts provider performance. To soften collinearity problems, we explore the use of least absolute shrinkage and selection operator regression as a variable selection method and Theil-Goldberger mixed estimation to augment the available information. We use data from the Belgian Transcatheter Aorta Valve Implantation (TAVI) registry, containing information on the first 860 TAVI procedures in Belgium. We find that treating an additional TAVI patient is associated with an increase in the probability of 2-year survival by about 0.16%-points. For adverse events like renal failure and stroke, we find that an extra day between procedures is associated with an increase in the probability for these events by 0.12%-points and 0.07%-points, respectively. Furthermore, we find evidence for positive learning effects from physicians' experience with defibrillation, treating patients with hypertension, and the use of certain types of replacement valves during the TAVI procedure. Copyright © 2017 John Wiley & Sons, Ltd.

Influence of variable oxygen concentration on the response of cells to heat or x irradiation

International Nuclear Information System (INIS)

Gerweck, L.E.; Richards, B.; Jennings, M.

1981-01-01

The influence of oxygen concentration on the lethal response of cells exposed to 43 0 C hyperthermia was determined and compared to the response of cells exposed to radiation under equivalent culturing and environmental conditions. Chinese hamster ovary (CHO) cells were heated or irradiated 0.5 h after induction of hypoxia and then reoxygenated following treatment. The oxygen enhancement ratio (OER) for heat or radiation was determined at the 1% survival level from least-squares fit of survival curves. A maximum OER of 3.1 +- 0.2 was observed in the 20 to 95% oxygen concentration range. The OER for heat, however, was 1.0 +- 0.1 irrespective of the gas-phase oxygen concentration. These results show that the lethal effects of heat are not influenced by the oxygen concentration at the time of treatment in CHO cells exposed to 43 0 C hyperthermia

Modeling global and local dependence in a pair of commodity forward curves with an application to the US natural gas and heating oil markets

International Nuclear Information System (INIS)

Ohana, Steve

2010-01-01

The goal of this paper is to present a model for the joint evolution of correlated commodity forward curves. Each forward curve is directed by two state variables, namely slope and level, and the model is meant to capture both the local and global dependence structures between slopes and levels. Our framework can be interpreted as an extension of the concept of cointegration to forward curves. The model is applied to a US database of heating oil and natural gas futures prices over the period February 2000-February 2009. We find the long-run slope and level relationships between natural gas and heating oil markets, analyze the lead and lag properties between the two energy commodities, the volatilities and correlations between their daily co-movements and evaluate the robustness of these observations to the turmoil experienced by energy markets since 2003. (author)

Effect of the medium characteristics and the heating and cooling rates on the nonisothermal heat resistance of Bacillus sporothermodurans IC4 spores.

Science.gov (United States)

Esteban, María-Dolores; Huertas, Juan-Pablo; Fernández, Pablo S; Palop, Alfredo

2013-05-01

In recent years, highly thermo-resistant mesophilic spore-forming bacteria belonging to the species Bacillus sporothermodurans have caused non-sterility problems in industrial sterilization processes. The aim of this research was to evaluate the effect of the heating medium characteristics (pH and buffer/food) on the thermal inactivation of B. sporothermodurans spores when exposed to isothermal and non-isothermal heating and cooling treatments and the suitability of non-linear Weibull and Geeraaerd models to predict the survivors of these thermal treatments. Thermal treatments were carried out in pH 3, 5 and 7 McIlvaine buffer and in a courgette soup. Isothermal survival curves showed shoulders that were accurately characterized by means of both models. A clear effect of the pH of the heating medium was observed, decreasing the D120 value from pH 7 to pH 3 buffer down to one third. Differences in heat resistance were similar, regardless of the model used and were kept at all temperatures tested. The heat resistance in courgette soup was similar to that shown in pH 7 buffer. When the heat resistance values obtained under isothermal conditions were used to predict the survival in the non-isothermical experiments, the predictions estimated the experimental data quite accurately, both with Weibull and Geeraerd models. Copyright © 2012 Elsevier Ltd. All rights reserved.

Thermoluminescence glow curve for UV induced ZrO2:Ti phosphor with variable concentration of dopant and various heating rate

Directory of Open Access Journals (Sweden)

Neha Tiwari

2014-10-01

Full Text Available The present paper reports the synthesis and characterization of Ti doped ZrO2 nanophosphors. The effects of variable concentration of titanium on thermoluminescence (TL behaviour are studied. The samples were prepared by combustion a synthesis technique which is suitable for less time taking techniques also for large scale production for nano phosphors. The starting material used for sample preparation are Zr(NO33 and Ti(NO33 and urea used as a fuel. The prepared sample was characterized by X-ray diffraction technique (XRD with variable concentration of Ti (0.05–0.5 mol% there is no any phase change found with increase the concentration of Ti. Sample shows cubic structure and the particle size calculated by Scherer's formula. The surface morphology of prepared phosphor was determined by field emission gun scanning electron microscopy (FEGSEM technique for optimized concentration of dopant. The good connectivity with grains and the semi-sphere like structure was found by FEGSEM. The functional group analysis was determined by Fourier transform infrared (FTIR spectroscopic techniques. The prepared phosphor examined by thermoluminescence technique. For recording TL glow curve every time 2 mg phosphor was irradiated by UV 254 nm source and fixed the heating rate at 5 °C s−1. Sample shows well resolved peak at 167 °C with a shoulder peak at 376 °C. The higher temperature peak shows the well stability and less fading in prepared phosphor. Also the effect of Ti concentration at fixed UV exposure time was studied. The effect of UV exposure time and dose versus intensity plot was studied. Sample shows linear response with dose and broaden peak with high temperature shows the more stability and less fading in TL glow curve. The linear dose response, high stability and less fading phenomenon shows the sample may be useful for thermoluminescence dosimetry application. Trapping parameters are calculated for every recorded glow curve. The

Modification by preirradiation growth conditions of the shoulder of the UV fluence-survival curve of Escherichia coli B/r WP2 thy trp and changes in mutagenic response toward tryptophan prototrophy

International Nuclear Information System (INIS)

Doudney, C.O.

1978-01-01

The distinct three-section UV fluence-mutation frequency response (MFR) curve demonstrated in Escherichia coli strain B/r WP2 thy trp and its uvrA derivative supports the SOS hypothesis and suggests that trp + revertants can arise either from isolated lesions (1DM) plus SOS induction or from two lesions in proximity (2DM). Preirradiation growth on arabinose instead of glucose converted the fluence-survival curve from highly shouldered to exponential but did not affect the three-section MFR curve. Prestarvation of the uvrA + strain for typtophan, which drastically increases the expanse of the shoulder of the survival curve, greatly decreased both 1DM and 2DM. With the uvrA strain the increase in shoulder expanse after typtophan prestarvation was accompanied by greatly increased 2DM but no change in 1DM. Preincubation with chloramphenicol induced an even greater increase in 2DM response than amino acid prestarvation. Nalidixic acid, which prevents DNA accumulation, eliminated the response. (Auth.)

Contribution to the boiling curve of sodium

International Nuclear Information System (INIS)

Schins, H.E.J.

1975-01-01

Sodium in a pool was preheated to saturation temperatures at system pressures of 200, 350 and 500 torr. A test section of normal stainless steel was then extra heated by means of the conical fitting condenser zone of a heat pipe. Measurements were made of heat transfer fluxes, q in W/cm 2 , as a function of wall excess temperature above saturation, THETA = Tsub(w) - Tsub(s) in 0 C, both, in natural convection and in boiling regimes. These measurements make it possible to select the Subbotin natural convection and nucleate boiling curves among other variants proposed in literature. Further it is empirically demonstrated on water that the minimum film boiling point corresponds to the homogeneous nucleation temperature calculated by the Doering formula. Assuming that the minimum film boiling point of sodium can be obtained in the same manner, it is then possible to give an appoximate boiling curve of sodium for the use in thermal interaction studies. At 1 atm the heat transfer fluxes q versus wall temperatures THETA are for a point on the natural convection curve 0.3 W/cm 2 and 2 0 C; for start of boiling 1.6 W/cm 2 and 6 0 C; for peak heat flux 360 W/cm 2 and 37 0 C; for minimum film boiling 30 W/cm 2 and 905 0 C and for a point on the film boiling curve 160 W/cm 2 and 2,000 0 C. (orig.) [de

Effect of heat treatment on the survival of Escherichia Coli O157:H7 ...

African Journals Online (AJOL)

The survival of Escherichia coli O157:H7 in raw milk treated in experimental pasteurizer was investigated in the year 2010. Raw milk was inoculated with different initial concentrations of E. coli O157:H7 and heated for 15 seconds at temperatures ranging from 69OC to 73OC. E. coli O157:H7 cells were not isolated from the ...

Forkhead Box M1 Is Regulated by Heat Shock Factor 1 and Promotes Glioma Cells Survival under Heat Shock Stress*

Science.gov (United States)

Dai, Bingbing; Gong, Aihua; Jing, Zhitao; Aldape, Kenneth D.; Kang, Shin-Hyuk; Sawaya, Raymond; Huang, Suyun

2013-01-01

The forkhead box M1 (FoxM1) is a key transcription factor regulating multiple aspects of cell biology. Prior studies have shown that FoxM1 is overexpressed in a variety of human tumors, including brain tumor, and plays a critical role in cancer development and progression. In this study we found that FoxM1 was up-regulated by heat shock factor 1 (HSF1) under heat shock stress condition in multiple cell lines. Knockdown of HSF1 with HSF1 siRNA or inhibition of HSF1 with a HSF1 inhibitor abrogated heat shock-induced expression of FoxM1. Genetic deletion of HSF1 in mouse embryo fibroblast cells also abolished heat shock stress-induced FoxM1 expression. Moreover, we showed that HSF1 directly bound to FoxM1 promoter and increased FoxM1 promoter activity. Furthermore, we demonstrated that FoxM1 was required for the G2-M phase progression through regulating Cdc2, Cdc20, and Cdc25B under a mild heat shock stress but enhanced cell survival under lethal heat shock stress condition. Finally, in human glioblastoma specimens, FoxM1 overexpression correlated with elevated HSF1 expression. Our results indicate that FoxM1 is regulated by HSF1 and is critical for HSF1-mediated heat shock response. We demonstrated a novel mechanism of stress resistance controlled by HSF1 and a new HSF-FoxM1 connection that mediates cellular thermotolerance. PMID:23192351

Applications of artificial neutral network for the prediction of flow boiling curves

International Nuclear Information System (INIS)

Su Guanghui; Jia Dounan; Fukuda, Kenji; Morita, Koji; Pidduck, Mark; Matsumoto, Tatsuya; Akasaka, Ryo

2002-01-01

An artificial neural network (ANN) was applied successfully to predict flow boiling curves. The databases used in the analysis are from the 1960's, including 1,305 data points which cover these parameter ranges: pressure P=100-1,000 kPa, mass flow rate G=40-500 kg/m 2 ·s, inlet subcooling ΔT sub =0-35degC, wall superheat ΔT w =10-300degC and heat flux Q=20-8,000 kW/m 2 . The proposed methodology allows us to achieve accurate results, thus it is suitable for the processing of the boiling curve data. The effects of the main parameters on flow boiling curves were analyzed using the ANN. The heat flux increases with increasing inlet subcooling for all heat transfer modes. Mass flow rate has no significant effects on nucleate boiling curves. The transition boiling and film boiling heat fluxes will increase with an increase in the mass flow rate. Pressure plays a predominant role and improves heat transfer in all boiling regions except the film boiling region. There are slight differences between the steady and the transient boiling curves in all boiling regions except the nucleate region. The transient boiling curve lies below the corresponding steady boiling curve. (author)

Peristaltic flow of Powell-Eyring fluid in curved channel with heat transfer: A useful application in biomedicine.

Science.gov (United States)

Hina, S; Mustafa, M; Hayat, T; Alsaedi, A

2016-10-01

In this work, we explore the heat transfer characteristics in the peristaltic transport of Powell-Eyring fluid inside a curved channel with complaint walls. The study has motivation toward the understanding of blood flow in microcirculatory system. Formulation is developed in the existence of velocity slip and temperature jump conditions. Perturbation approach has been utilized to present series expressions of axial velocity and temperature distributions. Streamlines are prepared to analyze the interesting phenomenon of trapping. Moreover, the plots of heat transfer coefficient for a broad range of embedded parameters are presented and discussed. The results indicate that slip effects substantially influence the velocity and temperature distributions. Axial flow accelerates when slip parameter is incremented. Temperature rises and wall heat flux grows when viscous dissipation effect is strengthened. In contrast to the planar channels, here velocity and temperature functions do not exhibit symmetry with respect to the central line. In addition, bolus size and its shape are different in upper and lower portions of the channel. Heat transfer coefficient enlarges when the curvature effects are reduced. The behaviors of wall tension and wall mass parameters on the profiles are qualitatively similar. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Toxigenic potential and heat survival of spore-forming bacteria isolated from bread and ingredients.

Science.gov (United States)

De Bellis, Palmira; Minervini, Fiorenza; Di Biase, Mariaelena; Valerio, Francesca; Lavermicocca, Paola; Sisto, Angelo

2015-03-16

Fifty-four spore-forming bacterial strains isolated from bread ingredients and bread, mainly belonging to the genus Bacillus (including Bacillus cereus), together with 11 reference strains were investigated to evaluate their cytotoxic potential and heat survival in order to ascertain if they could represent a risk for consumer health. Therefore, we performed a screening test of cytotoxic activity on HT-29 cells using bacterial culture filtrates after growing bacterial cells in Brain Heart Infusion medium and in the bread-based medium Bread Extract Broth (BEB). Moreover, immunoassays and PCR analyses, specifically targeting already known toxins and related genes of B. cereus, as well as a heat spore inactivation assay were carried out. Despite of strain variability, the results clearly demonstrated a high cytotoxic activity of B. cereus strains, even if for most of them it was significantly lower in BEB medium. Cytotoxic activity was also detected in 30% of strains belonging to species different from B. cereus, although, with a few exceptions (e.g. Bacillus simplex N58.2), it was low or very low. PCR analyses detected the presence of genes involved in the production of NHE, HBL or CytK toxins in B. cereus strains, while genes responsible for cereulide production were not detected. Production of NHE and HBL toxins was also confirmed by specific immunoassays only for B. cereus strains even if PCR analyses revealed the presence of related toxin genes also in some strains of other species. Viable spore count was ascertained after a heat treatment simulating the bread cooking process. Results indicated that B. amyloliquefaciens strains almost completely survived the heat treatment showing less than 2 log-cycle reductions similarly to two strains of B. cereus group III and single strains belonging to Bacillus subtilis, Bacillus mojavensis and Paenibacillus spp. Importantly, spores from strains of the B. cereus group IV exhibited a thermal resistance markedly lower than B

Prediction of flow boiling curves based on artificial neural network

International Nuclear Information System (INIS)

Wu Junmei; Xi'an Jiaotong Univ., Xi'an; Su Guanghui

2007-01-01

The effects of the main system parameters on flow boiling curves were analyzed by using an artificial neural network (ANN) based on the database selected from the 1960s. The input parameters of the ANN are system pressure, mass flow rate, inlet subcooling, wall superheat and steady/transition boiling, and the output parameter is heat flux. The results obtained by the ANN show that the heat flux increases with increasing inlet sub cooling for all heat transfer modes. Mass flow rate has no significant effects on nucleate boiling curves. The transition boiling and film boiling heat fluxes will increase with an increase of mass flow rate. The pressure plays a predominant role and improves heat transfer in whole boiling regions except film boiling. There are slight differences between the steady and the transient boiling curves in all boiling regions except the nucleate one. (authors)

Neutron and photon clonogenic survival curves of two chemotherapy resistant human intermediate-grade non-Hodgkin lymphoma cell lines

International Nuclear Information System (INIS)

Aref, Amr; Yudelev, Mark; Mohammad, Ramzi; Choudhuri, Rajani; Orton, Colin; Al-Katib, Ayad

1999-01-01

Background: The potential role of neutron therapy in the management of intermediate-grade non-Hodgkin lymphoma (IGNHL) has not been examined because of the belief that the anticipated radiobiological effectiveness (RBE) would be uniformly very low. Purpose: To determine the fast neutron RBE for two chemotherapy-resistant IGNHL cell lines. Methods and Materials: Conventional soft agar clonogenic survival curves following irradiation by 60 Co and fast neutron were established for two IGNHL cell lines. These cell lines, WSU-DLCL2 and SK-DHL2B, were found in previous studies to be able to repair sublethal damage, and were also resistant to L-Pam and doxorubicin chemotherapy. Results: When the surviving fraction after 2 Gy photon was chosen as the biological endpoint, the RBE for WSU-DLCL2 and SK-DHL2B measured 3.34 and 3.06. Similarly, when 10% survival was considered, the RBE for these two cell lines measured 2.54 and 2.59. The RBE, as measured by the ratios α neutron/α photon, for WSU-DLCL2, SK-DHL2B cell lines are 6.67 and 5.65, respectively. These results indicate that the RBE for these IGNHL cell lines is higher than the average RBE for cell lines of other histological types. Conclusion: Fast neutron irradiation may be of potential value in treating selected cases of IGNHL

Generalized drying curves in conductive/convective paper drying

Directory of Open Access Journals (Sweden)

O.C. Motta Lima

2000-12-01

Full Text Available This work presents a study related to conductive/convective drying of paper (cellulose sheets over heated surfaces, under natural and forced air conditions. The experimental apparatus consists in a metallic box heated by a thermostatic bath containing an upper surface on which the paper samples (about 1 mm thick are placed. The system is submitted to ambient air under two different conditions: natural convection and forced convection provide by an adjustable blower. The influence of initial paper moisture content, drying (heated surface temperature and air velocity on drying curves behavior is observed under different drying conditions. Hence, these influence is studied through the proposal of generalized drying curves. Those curves are analyzed individually for each air condition exposed above and for both together. A set of equations to fit them is proposed and discussed.

Visualized study on specific points on demand curves and flow patterns in a single-side heated narrow rectangular channel

International Nuclear Information System (INIS)

Wang Junfeng; Huang Yanping; Wang Yanlin

2011-01-01

Highlights: → Specific points on the demand curve and flow patterns are visually studied. → Bubbly, churn, and annular flows were observed. → Onset of flow instability and bubbly-churn transition occurs at the same time. → The evolution of specific points and flow pattern transitions were examined. - Abstract: A simultaneous visualization and measurement study on some specific points on demand curves, such as onset of nucleate boiling (ONB), onset of significant void (OSV), onset of flow instability (OFI), and two-phase flow patterns in a single-side heated narrow rectangular channel, having a width of 40 mm and a gap of 3 mm, was carried out. New experimental approaches were adopted to identify OSV and OFI in a narrow rectangular channel. Under experimental conditions, the ONB could be predicted well by the Sato and Matsumura model. The OSV model of Bowring can reasonably predict the OSV if the single-side heated condition is considered. The OFI was close to the saturated boiling point and could be described accurately by Kennedy's correlation. The two-phase flow patterns observed in this experiment could be classified into bubbly, churn, and annular flow. Slug flow was never observed. The OFI always occurred when the bubbles at the channel exit began to coalesce, which corresponded to the beginning of the bubbly-churn transition in flow patterns. Finally, the evolution of specific points and flow pattern transitions were examined in a single-side heated narrow rectangular channel.

Phase Curve Analysis of Super-Earth 55 Cancri e

Science.gov (United States)

Angelo, Isabel; Hu, Renyu

2018-01-01

One of the primary questions when characterizing Earth-sized and super-Earth-sized exoplanets is whether they have a substantial atmosphere like Earth and Venus, or a bare-rock surface that may come with a tenuous atmosphere like Mercury. Phase curves of the planets in thermal emission provide clues to this question, because a substantial atmosphere would transport heat more efficiently than a bare-rock surface. Analyzing phase curve photometric data around secondary eclipse has previously been used to study energy transport in the atmospheres of hot Jupiters. Here we use phase curve, Spitzer time-series photometry to study the thermal emission properties of the super-Earth exoplanet 55 Cancri e. We utilize a previously developed semi-analytical framework to fit a physical model to infrared photometric data of host star 55 Cancri from the Spitzer telescope IRAC 2 band at 4.5 μm. The model uses various parameters of planetary properties including Bond albedo, heat redistribution efficiency (i.e., the ratio between the radiative timescale and advective timescale of the photosphere), and atmospheric greenhouse factor. The phase curve of 55 Cancri e is dominated by thermal emission with an eastward-shifted hot spot located on the planet surface. We determine the heat redistribution efficiency to be ≈1.47, which implies that the advective timescale is on the same order as the radiative timescale. This requirement from the phase curve cannot be met by the bare-rock planet scenario, because heat transport by currents of molten lava would be too slow. The phase curve thus favors the scenario with a substantial atmosphere. Our constraints on the heat redistribution efficiency translate to a photosphere pressure of ~1.4 bar. The Spitzer IRAC 2 band is thus a window into the deep atmosphere of the planet 55 Cancri e.

In utero heat stress decreases calf survival and performance through the first lactation.

Science.gov (United States)

Monteiro, A P A; Tao, S; Thompson, I M T; Dahl, G E

2016-10-01

Calves born to cows exposed to heat stress during late gestation (i.e., the dry period) have lower birth weight and weaning weight and compromised passive immune transfer compared with those born to dams that are cooled. However, it is unknown if heat stress in utero has carryover effects after weaning. The objective was to evaluate the effect of heat stress (HT) or cooling (CL) in late gestation dairy cows on the survival, growth, fertility, and milk production in the first lactation of their calves. Data of animals obtained from previous experiments conducted during 5 consecutive summers in Florida were pooled and analyzed. Cows were dried off 46d before expected calving and randomly assigned to 1 of 2 treatments, HT or CL. Cooled cows were housed with sprinklers, fans, and shade, whereas only shade was provided to HT cows. Within 4h of birth, 3.8 L of colostrum was fed to calves from both groups of cows. All calves were managed in the same manner and weaned at 49d of age. Birth weight and survival of 146 calves (HT=74; CL=72) were analyzed. Additionally, body weight, growth rate, fertility, and milk production in the first lactation from 72 heifers (HT=34; CL=38) were analyzed. As expected, HT calves were lighter (means ± SEM; 39.1±0.7 vs. 44.8±0.7kg) at birth than CL calves. Cooled heifers were heavier up to 1yr of age, but had similar total weight gain (means ± SEM; 305.8±6.3 vs. 299.1±6.3kg, respectively) compared with HT heifers. No effect of treatment was observed on age at first insemination (AI) and age at first parturition. Compared with CL heifers, HT heifers had a greater number of services per pregnancy confirmed at d 30 after AI, but no treatment effect was observed on number of services per pregnancy confirmed at d 50 after AI. A greater percentage of CL heifers reached first lactation compared with HT heifers (85.4 vs. 65.9%). Moreover, HT heifers produced less milk up to 35wk of the first lactation compared with CL heifers (means ± SEM; 26

Logistic characteristics of phonon transport in silicon thin film: the S-curve

Energy Technology Data Exchange (ETDEWEB)

Yilbas, B.S., E-mail: bsyilbas@kfupm.edu.sa; Mansoor, S. Bin

2013-10-01

The logistic characteristics of the averaged heat flux are investigated across the thin film incorporating the S-curve. Temporal behaviour of the heat flux vector is computed using the Boltzmann transport equation. The dispersion relations are introduced to account for the frequency dependent phonon transport across the film. The influence of film width on the characteristics of the averaged heat flux is also examined. It is found that temporal behaviour of the averaged heat flux follows the S-curve. The S-curve characteristics change for different film widths. The time to reach 95% steady value of the averaged heat flux is short for the film with small widths, which is attributed to the ballistic behaviour of phonons in the film.

Logistic characteristics of phonon transport in silicon thin film: the S-curve

International Nuclear Information System (INIS)

Yilbas, B.S.; Mansoor, S. Bin

2013-01-01

The logistic characteristics of the averaged heat flux are investigated across the thin film incorporating the S-curve. Temporal behaviour of the heat flux vector is computed using the Boltzmann transport equation. The dispersion relations are introduced to account for the frequency dependent phonon transport across the film. The influence of film width on the characteristics of the averaged heat flux is also examined. It is found that temporal behaviour of the averaged heat flux follows the S-curve. The S-curve characteristics change for different film widths. The time to reach 95% steady value of the averaged heat flux is short for the film with small widths, which is attributed to the ballistic behaviour of phonons in the film

Physiology and Endocrinology Symposium: The current status of heat shock in early embryonic survival and reproductive efficiency

Science.gov (United States)

The Physiology and Endocrinology Symposium entitled “The Current Status of Heat Shock in Early Embryonic Survival and Reproductive Efficiency” was held at the Joint ADSA-CSAS-AMPA-WSAS-ASAS Meeting in Phoenix, Arizona, July 15 to 19, 2012. In recent years, data has accumulated suggesting a role for...

Depression and Liver Transplant Survival.

Science.gov (United States)

Meller, William; Welle, Nicole; Sutley, Kristen; Thurber, Steven

Patients who underwent liver transplantation and experienced clinical depression have heretofore evinced lower survival rates when compared to nondepressed counterparts. To investigate the hypothesis that transplant patients who seek and obtain medical treatment for depression would circumvent the prior reduced survival findings. A total of 765 patients with liver transplants were scrutinized for complications following transplantation. Further, 104 patients experienced posttransplant depression as manifested by diagnosis and treatment by medical personnel. Survival analyses were conducted comparing hazard and survival curves for these selected individuals and the remainder of transplant patients. Contrary to prior data and consistent with the aforementioned hypothesis, median survival durations, survival curves, and hazard functions (controlling for age and prolonged posttransplant survival for the depressed patients were better. The improved survival for the depressed patients may simply be related to an amelioration of depressed symptoms via antidepressant medications. However, this interpretation would only be congruent with reduced hazard, not elevated survival, beyond the norm (median) for other transplant participants. Assuming the reliability and generalization of our findings, perhaps a reasonable and compelling interpretation is that combined with the effectiveness of antidepressant medications, the seeking and receiving treatment for depression is a type of proxy measure of a more global pattern of adherence to recommended posttransplant medical regimens. Copyright © 2017 The Academy of Psychosomatic Medicine. Published by Elsevier Inc. All rights reserved.

Hemopoietic stem-cell compartment of the SCID mouse: Double-exponential survival curve after γ irradiation

International Nuclear Information System (INIS)

Taniguchi, Satoshi; Hirabayashi, Yoko; Inoue, Tohru; Kanisawa, Masayoshi; Sasaki, Hideki; Komatsu, Kenshi; Mori, K.J.

1993-01-01

It has been reported that SCID (severe combined immunodeficiency, scid/scid) mice are more radiosensitive than normal mice. In the present studies, graded doses of radiation were given to bone marrow cells from SCID mice, and double-exponential survival curves were observed for day-9 and day-12 colony-forming units in the spleen (CFU-S). Single-exponential curves were found for SCID CFU in in vitro assays for granulocyte/macrophage-CFUs and erythroid burst-forming units, as reported elsewhere. Since the size of this more resistant fraction seems to decrease with stem-cell maturation, the finding implies that this fraction is a primitive subpopulation of the stem-cell compartment. The mean lethal dose (D 0 ), however, of this less sensitive SCID CFU-S is much less than the D 0 of regular CFU-S in normal littermates. Spleen colonies produced by SCID bone marrow were relatively small and abortive. The size of these colonies decreased nearly exponentially with increasing doses of radiation. These colonies produced by the sensitive fraction have disappeared, being killed by a relatively low dose of radiation. This observation might account for the high lymphomagenesis arising from primitive hemopoietic stem cells in SCID mice, because the smallness of the colonies suggests that there is unrepaired or misrepaired damage. Furthermore, this less sensitive fraction might be a source of the open-quotes leakyclose quotes change of T and B cells, possibly due to the induction of an equivocal repair system which appears in the later stages of life in the SCID mice. 34 refs., 5 figs., 3 tabs

CAN LARGE TIME DELAYS OBSERVED IN LIGHT CURVES OF CORONAL LOOPS BE EXPLAINED IN IMPULSIVE HEATING?

International Nuclear Information System (INIS)

Lionello, Roberto; Linker, Jon A.; Mikić, Zoran; Alexander, Caroline E.; Winebarger, Amy R.

2016-01-01

The light curves of solar coronal loops often peak first in channels associated with higher temperatures and then in those associated with lower temperatures. The delay times between the different narrowband EUV channels have been measured for many individual loops and recently for every pixel of an active region observation. The time delays between channels for an active region exhibit a wide range of values. The maximum time delay in each channel pair can be quite large, i.e., >5000 s. These large time delays make-up 3%–26% (depending on the channel pair) of the pixels where a trustworthy, positive time delay is measured. It has been suggested that these time delays can be explained by simple impulsive heating, i.e., a short burst of energy that heats the plasma to a high temperature, after which the plasma is allowed to cool through radiation and conduction back to its original state. In this paper, we investigate whether the largest observed time delays can be explained by this hypothesis by simulating a series of coronal loops with different heating rates, loop lengths, abundances, and geometries to determine the range of expected time delays between a set of four EUV channels. We find that impulsive heating cannot address the largest time delays observed in two of the channel pairs and that the majority of the large time delays can only be explained by long, expanding loops with photospheric abundances. Additional observations may rule out these simulations as an explanation for the long time delays. We suggest that either the time delays found in this manner may not be representative of real loop evolution, or that the impulsive heating and cooling scenario may be too simple to explain the observations, and other potential heating scenarios must be explored

Survival patterns and hemopathological responses of dogs under continuous gamma irradiation

International Nuclear Information System (INIS)

Seed, T.M.; Fritz, T.E.; Tolle, D.V.; Poole, C.M.; Lombard, L.S.; Doyle, D.E.; Kaspar, L.V.; Cullen, S.M.; Carnes, B.A.

1983-01-01

Survival curves were constructed and analyzed relative to contributing hematopathological responses for groups of beagles exposed continuously for duration of life to low daily doses of whole body 60 Co gamma irradiation (27.3 rads/day to 4 rads/day). The survival curves versus time were progressively displaced toward longer survival as rates of exposure were reduced from the relatively high dose rate of 27.3 rads/day to the low dose rate of 4.0 rads/day. Average survival times increased from 57 days at 27.3 rads/day to 1830 days at 4.0 rads/day, representing fractional increased life-spans from 1.5% to 50.8%, respectively. Survival curves versus total dose were markedly displaced along the cumulative radiation dose axis at the extreme dose rates (i.e., 27.3 and 4.0 rads/day), but not at the intermediate dose rates (i.e., 13.4 and 7.9 rads/day) in which the upper linear portions of the survival curves are superimposed. From these dose-dependent survival curves, LD 50 values for whole body gamma irradiation, delivered chronically at 27.3, 13.4, 7.9, and 4.0 rads per day were estimated to be 1442, 2124, 2039, and 7161 rads, respectively. Both time- and dose-dependent survival curves for the intermediate dose rates, in contrast to the extreme dose rates, exhibited pronounced transitions in the lethality rate below the 50% survival level. These lethality rate transitions occurred at approx. 2500 rads of accumulated dose and were attributed to a shift in the spectrum of developing hematopathologies: namely, from a predominance of the acutely ablative radiation-induced lymphohematopoietic syndromes (i.e., septicemias and aplastic anemias) to a predominance of the late arising hematopoietic neoplasias (myelogenous leukemia and related myeloproliferative disorders)

On the frontier of boiling curve and beyond design of its origin

International Nuclear Information System (INIS)

Stosic, Z.V.

2005-01-01

An advanced approach of Extended Design of the Boiling Curve beyond its origin is proposed. It is developed from the fact that both CHF (Critical Heat Flux) and rewetting affect the Boiling Curve on the heating surface through two simultaneous processes taking place on both sides of the heating surface. The first is two-phase flow thermal-hydraulics with resultant heat transferred from the heating surface to the coolant. The second one is the heat conduction through material itself, allied with the balance of generated and accumulated energy. Both of these processes are triggered by the change in HTC (Heat Transfer Coefficient) on the heating surface, which accordingly influences the Boiling Curve. Depending on direction of the Transition - from nucleate to film boiling or vice versa - these processes act differently and direct the Boiling Curve to diverse paths. The proposed physically based concept recognises this fact and introduces HTC as the triggering parameter with instant effect. It is implemented in the subchannel code COBRA 3-CP providing stable rewetting which has been deficient in COBRA since its origin. Results of validation and obtained agreements with transient measured data prove legality of the advanced concept of Boiling Curve. This approach is being used for transient analyses of PWR (Pressurised Water Reactor) gaining benefits from properly predicting the rewetting. The method is well-qualified to be applied also in other thermal-hydraulic codes like COBRA/TRAC, COBRA-TF, TRAC and/or RELAP, where the classical steady-state and poolboiling approach has been originally implemented. (author)

Summary curves for patients transplanted for chronic myeloid leukaemia salvaged by a donor lymphocyte infusion: the current leukaemia-free survival curve

DEFF Research Database (Denmark)

Klein, John P.; Keiding, Niels; Shu, Youyi

2000-01-01

CML, donor lymphocyte infusion, leukaemia-free survival, current leukaemia-free survival, statistical methods......CML, donor lymphocyte infusion, leukaemia-free survival, current leukaemia-free survival, statistical methods...

Heat exchangers

Energy Technology Data Exchange (ETDEWEB)

Schmidt, E L; Eisenmann, G; Hahne, E [Stuttgart Univ. (TH) (F.R. Germany). Inst. fuer Thermodynamik und Waermetechnik

1976-04-01

A survey is presented on publications on design, heat transfer, form factors, free convection, evaporation processes, cooling towers, condensation, annular gap, cross-flowed cylinders, axial flow through a bundle of tubes, roughnesses, convective heat transfer, loss of pressure, radiative heat transfer, finned surfaces, spiral heat exchangers, curved pipes, regeneraters, heat pipes, heat carriers, scaling, heat recovery systems, materials selection, strength calculation, control, instabilities, automation of circuits, operational problems and optimization.

Survival curves study of platelet labelling with 51Cr

International Nuclear Information System (INIS)

Penas, M.E.

1981-01-01

Platelet kinetics and idiopathic thrombocytopenic purpura were researched in the literature. An 'in vitro' platelet labelling with 51 Cr procedure in implementation has been evaluated in human beings. Functions used for fitting considered the cases whether the curve was linear or exponential as well as the presence of hematies. (author)

Predicting long-term graft survival in adult kidney transplant recipients

Directory of Open Access Journals (Sweden)

Brett W Pinsky

2012-01-01

Full Text Available The ability to accurately predict a population′s long-term survival has important implications for quantifying the benefits of transplantation. To identify a model that can accurately predict a kidney transplant population′s long-term graft survival, we retrospectively studied the United Network of Organ Sharing data from 13,111 kidney-only transplants completed in 1988- 1989. Nineteen-year death-censored graft survival (DCGS projections were calculated and com-pared with the population′s actual graft survival. The projection curves were created using a two-part estimation model that (1 fits a Kaplan-Meier survival curve immediately after transplant (Part A and (2 uses truncated observational data to model a survival function for long-term projection (Part B. Projection curves were examined using varying amounts of time to fit both parts of the model. The accuracy of the projection curve was determined by examining whether predicted sur-vival fell within the 95% confidence interval for the 19-year Kaplan-Meier survival, and the sample size needed to detect the difference in projected versus observed survival in a clinical trial. The 19-year DCGS was 40.7% (39.8-41.6%. Excellent predictability (41.3% can be achieved when Part A is fit for three years and Part B is projected using two additional years of data. Using less than five total years of data tended to overestimate the population′s long-term survival, accurate prediction of long-term DCGS is possible, but requires attention to the quantity data used in the projection method.

Burial duration, depth and air pocket explain avalanche survival patterns in Austria and Switzerland.

Science.gov (United States)

Procter, Emily; Strapazzon, Giacomo; Dal Cappello, Tomas; Zweifel, Benjamin; Würtele, Andreas; Renner, Andreas; Falk, Markus; Brugger, Hermann

2016-08-01

To calculate the first Austrian avalanche survival curve and update a Swiss survival curve to explore survival patterns in the Alps. Avalanche accidents occurring between 2005/06 and 2012/13 in Austria and Switzerland were collected. Completely buried victims (i.e. burial of the head and chest) in open terrain with known outcome (survived or not survived) were included in the analysis. Extrication and survival curves were calculated using the Turnbull algorithm, as in previous studies. 633 of the 796 completely buried victims were included (Austria n=333, Switzerland n=300). Overall survival was 56% (Austria 59%; Switzerland 52%; p=0.065). Time to extrication was shorter in Austria for victims buried ≤60min (p15min. The survival curves resembled those previously published and support the idea that underlying survival patterns are reproducible. The results are in accordance with current recommendations for management of avalanche victims and serve as a reminder that expedient companion rescue within a few minutes is critical for survival. An air pocket was shown to be a positive prognostic factor for survival. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Impact of Sodium Chloride and Heat on Survival Time of Linguatula Serrata Nymphs in vitro: An Experimental Study

Directory of Open Access Journals (Sweden)

B. Hajimohammadi

2012-07-01

Full Text Available Introduction: Linguatula serrata is a zoonotic parasite, belonging to the class Pentastomida. The major aim of this study was to evaluate the impact of sodium chloride (NaCl and heat on survival time of Linguatula serrata nymphs. Materials & Methods: Thirty nymphs (10 in triplicate were separately transferred to plastic tubes, containing different concentrations of NaCl solution (2%, 5% and 10%. Meanwhile, 30 nymphs in tubes containing Phosphate Buffer Saline (PBS were separately treated by +50°C, +60°C and +72°C. As control group, thirty nymphs were stored in PBS at +4°C. The effects of different conditions on survival time of the nymphs were evaluated by observing their motility in different periods of time. Results: The survival time of the nymphs stored in 10% NaCl solution was too short and all of them were dead after 3 hours. But the other ones maintained in 2% NaCl solution were significantly more resistant (p<0.05 and were survived for 2 days. All the nymphs pertaining to each +60°C and +72°C treatments were found dead after first 5-minute storage interval; the nymphs stored at +50°C died totally after 20 minutes. The nymphs maintained in PBS at +4°C (control group showed the longest survival time (p<0.05; all of them were alive until day 4 and the last ones died on day 34. Conclusion: It is concluded that salting and heating have significant parasiticidal effects on L. serrata nymphs and could be used as disinfecting methods in processing of meat products especially liver. However, refrigeration at +4°C increases the resistance of the nymphs in meat products and therefore might endanger the food safety.

Boiling curve in high quality flow boiling

International Nuclear Information System (INIS)

Shiralkar, B.S.; Hein, R.A.; Yadigaroglu, G.

1980-01-01

The post dry-out heat transfer regime of the flow boiling curve was investigated experimentally for high pressure water at high qualities. The test section was a short round tube located downstream of a hot patch created by a temperature controlled segment of tubing. Results from the experiment showed that the distance from the dryout point has a significant effect on the downstream temperatures and there was no unique boiling curve. The heat transfer coefficients measured sufficiently downstream of the dryout point could be correlated using the Heineman correlation for superheated steam, indicating that the droplet deposition effects could be neglected in this region

Comparison of radiosensitivity and thermosensitivity among three types of cultured mammalian cells and detection of heat-induced cell killing by eosin-staining method

Energy Technology Data Exchange (ETDEWEB)

Kashiwado, Kouzou

1988-12-01

Radiosensitivity, Thermosensitivity and their combined sensitivity on cell death were studied using mouse L5178Y, mouse FM3A and human Burkitt lymphoma. Eosin-staining method was tested for counting the heat-induced dead cells. The results obtained in the present study were as follows: (1) In irradiation with /sup 60/Co gamma-rays D/sub 0/ values of 1.3 Gy, 1.4 Gy and 1.7 Gy were obtained for Burkitt lymphoma, L5178Y and FM3A respectively. (2) By heating at 43degC, T/sub 0/ values of 4.1 min, 12.5 min and 32 min were obtained for L5178Y, FM3A and Burkitt lymphoma respectively. (3) Thermotolerance decay depended on cell doubling time, that is, the shorter the doubling time, the faster the decay. Furthermore, the cell line with the higher thermosensitivity showed a faster decay of thermotolerance for the three cell lines used in the present study. (4) The radiosensitizing effects were nearly the same in all three cell lines. (5) Using eosin-staining method, the cell survival curves after hyperthermia were ascertained and compared with those obtained by colony forming method. In L5178Y the survival curves obtained by the two methods were nearly the same. In FM3A only some correlation was found betweewn the cell survival curves obtained by the two methods but in Burkitt lymphoma no correlation was found. (author) 52 refs.

Comparison of radiosensitivity and thermosensitivity among three types of cultured mammalian cells and detection of heat-induced cell killing by eosin-staining method

International Nuclear Information System (INIS)

Kashiwado, Kouzou

1988-01-01

Radiosensitivity, Thermosensitivity and their combined sensitivity on cell death were studied using mouse L5178Y, mouse FM3A and human Burkitt lymphoma. Eosin-staining method was tested for counting the heat-induced dead cells. The results obtained in the present study were as follows: 1) In irradiation with 60 Co gamma-rays D 0 values of 1.3 Gy, 1.4 Gy and 1.7 Gy were obtained for Burkitt lymphoma, L5178Y and FM3A respectively. 2) By heating at 43degC, T 0 values of 4.1 min, 12.5 min and 32 min were obtained for L5178Y, FM3A and Burkitt lymphoma respectively. 3) Thermotolerance decay depended on cell doubling time, that is, the shorter the doubling time, the faster the decay. Furthermore, the cell line with the higher thermosensitivity showed a faster decay of thermotolerance for the three cell lines used in the present study. 4) The radiosensitizing effects were nearly the same in all three cell lines. 5) Using eosin-staining method, the cell survival curves after hyperthermia were ascertained and compared with those obtained by colony forming method. In L5178Y the survival curves obtained by the two methods were nearly the same. In FM3A only some correlation was found betweewn the cell survival curves obtained by the two methods but in Burkitt lymphoma no correlation was found. (author) 52 refs

Critical behavior of binary mixture of {x C6H5CN + (1 - x) CH3(CH2)12CH3}: Measurements of coexistence curves, turbidity, and heat capacity

International Nuclear Information System (INIS)

Yin Tianxiang; Lei Yuntao; Huang Meijun; Chen Zhiyun; Mao Chunfeng; An Xueqin; Shen Weiguo

2011-01-01

Research highlights: → Coexistence curve, turbidity and heat capacity of critical solution were measured. → Critical amplitudes were determined to test universal ratios. → Complete scaling theory was verified. → Monotonic critical crossover behavior was demonstrated. - Abstract: (Liquid + liquid) coexistence curve, turbidity, and isobaric heat capacity per unit volume for the critical solution of {benzonitrile + n-tetradecane} have been measured. The critical exponents β, ν, γ, and α and system-dependent critical amplitudes B, ξ 0 , χ 0 , and A ± , corresponding to the difference of the general density variable of two coexisting phases Δρ, the correlation length ξ, the osmotic compressibility χ, and the isobaric heat capacity per unit volume C p V -1 , have been deduced and were used to test some universal ratios. The behavior of the diameter of the coexistence curves showed good agreement with the complete scaling theory. The analysis of effective critical exponent β eff , which was well described by the crossover model proposed by Anisimov and Sengers, and effective critical exponent α eff indicated monotonic crossover phenomena from 3D-Ising behavior to mean-field one as the temperature departed from the critical point.

Positional glow curve simulation for thermoluminescent detector (TLD) system design

International Nuclear Information System (INIS)

Branch, C.J.; Kearfott, K.J.

1999-01-01

Multi- and thin element dosimeters, variable heating rate schemes, and glow-curve analysis have been employed to improve environmental and personnel dosimetry using thermoluminescent detectors (TLDs). Detailed analysis of the effects of errors and optimization of techniques would be highly desirable. However, an understanding of the relationship between TL light production, light attenuation, and precise heating schemes is made difficult because of experimental challenges involved in measuring positional TL light production and temperature variations as a function of time. This work reports the development of a general-purpose computer code, thermoluminescent detector simulator, TLD-SIM, to simulate the heating of any TLD type using a variety of conventional and experimental heating methods including pulsed focused or unfocused lasers with Gaussian or uniform cross sections, planchet, hot gas, hot finger, optical, infrared, or electrical heating. TLD-SIM has been used to study the impact on the TL light production of varying the input parameters which include: detector composition, heat capacity, heat conductivity, physical size, and density; trapped electron density, the frequency factor of oscillation of electrons in the traps, and trap-conduction band potential energy difference; heating scheme source terms and heat transfer boundary conditions; and TL light scatter and attenuation coefficients. Temperature profiles and glow curves as a function of position time, as well as the corresponding temporally and/or spatially integrated glow values, may be plotted while varying any of the input parameters. Examples illustrating TLD system functions, including glow curve variability, will be presented. The flexible capabilities of TLD-SIM promises to enable improved TLD system design

First order reversal curve analysis on NdFeB nanocomposite ribbons subjected to Joule heating treatments

Energy Technology Data Exchange (ETDEWEB)

Pampillo, L.G. [INTECIN-Instituto de Tecnologias y ciencias de la Ingenieria ' Hilario Fernandez Long' (UBA-CONICET), Facultad de Ingenieria, Paseo Colon 850 (C1063ACV), C. A. B. A. (Argentina); Saccone, F.D., E-mail: fsaccone@fi.uba.ar [INTECIN-Instituto de Tecnologias y ciencias de la Ingenieria ' Hilario Fernandez Long' (UBA-CONICET), Facultad de Ingenieria, Paseo Colon 850 (C1063ACV), C. A. B. A. (Argentina); Knobel, M. [Instituto de Fisica Gleb Wataghin-Departamento de Fisica de Materia Condensada-Universidade Estadual de Campinas, Cidade Universitaria Zeferino Vaz, Barao Geraldo 13083-970, Campinas, Sao Paulo (Brazil); Sirkin, H.R.M. [INTECIN-Instituto de Tecnologias y ciencias de la Ingenieria ' Hilario Fernandez Long' (UBA-CONICET), Facultad de Ingenieria, Paseo Colon 850 (C1063ACV), C. A. B. A. (Argentina)

2012-09-25

Highlights: Black-Right-Pointing-Pointer Nd-lean amorphous precursors subjected to Joule heating. Black-Right-Pointing-Pointer Exchange-spring magnets. Black-Right-Pointing-Pointer FORC diagrams of irreversible switching fields. Black-Right-Pointing-Pointer This last techniques helped us to verify the optimized treatments conditions. - Abstract: Amorphous precursors with composition Nd{sub 4.5}Fe{sub 72-x}Co{sub 3+x}Cr{sub 2}Al{sub 1}B{sub 17.5} (x = 0, 2, 7, 12) were thermally treated by the Joule heating technique with a linearly varying electrical current. The crystallization kinetics was followed by monitoring the resistance of the ribbons during the heating up to the final applied current. Crystallized nanostructured phases coexist with an amorphous matrix, as it was observed by means of Moessbauer Spectroscopy and X-ray diffraction. The irreversible magnetic response of the Joule heated ribbons was analyzed by the First Order Reversal Curves (FORC) diagram technique. For the optimal treatments, associated with the higher maximum energy products for each sample composition, it was found that the main interaction is of a strongly dipolar characteristic. Over annealed samples show a FORC diagram that gives into account of softening, due to grain growth, for those phases precipitated at the first crystallization stage. When it is measured at 20 K, the hardest magnetic sample (Fe = 72 at.%, Co = 3 at.%, I{sub final} = 0.5 A), exhibits a diagram with characteristics corresponding to dipolar interactions of soft phases. This fact is consistent with an enhancement of the exchange length due to the increase in the soft phase stiffness as it is expected at low temperatures.

Anomalies in curved spacetime at finite temperature

International Nuclear Information System (INIS)

Boschi-Filho, H.; Natividade, C.P.

1993-01-01

We discuss the problem of the breakdown of conformal and gauge symmetries at finite temperature in curved spacetime background, when the changes in the background are gradual. We obtain the expressions for the Seeley's coefficients and the heat kernel expansion in this regime. As applications, we consider the self-interacting lambda phi''4 and chiral Schwinger models in curved backgrounds at finite temperature. (Author) 9 refs

Irradiations of human melanoma cells by 14 MeV neutrons; survival curves interpretation; physical simulation of neutrons interactions in the cellular medium

International Nuclear Information System (INIS)

Bodez, Veronique

2000-01-01

14 MeV neutrons are used to irradiate human melanoma cells in order to study survival curves at low dose and low dose rate. We have simulated with the MCNP code, transport of neutrons through the experimental setup to evaluate the contamination of the primary beam by gamma and electrons, for the feasibility of our experiments. We have shown a rapid decrease of the survival curve in the first cGy followed by a plateau for doses up to 30 cGy; after we observed an exponential decrease. This results are observed for the first time, for neutrons at low dose rate (5 cGy/h). In parallel with this experimental point, we have developed a simulation code which permitted the study of neutrons interactions with the cellular medium for individual cells defined as in our experimental conditions. We show that most of the energy is deposited by protons from neutron interactions with external medium, and by heavy ions for interactions into the cell. On the other hand the code gives a good order of magnitude of the dose rate, compared to the experimental values given by silicon diodes. The first results show that we can, using a theory based on induced repair of cells, give an interpretation of the observed experimental plateau. We can give an estimation of the radial distribution of dose for the tracks of charged ions, we show the possibility of calculate interaction cross sections with cellular organelles. Such a work gives interesting perspectives for the future in radiobiology, radiotherapy or radioprotection. (author) [fr

Adaptive response in Drosophila melanogaster heat shock proteins mutant strains

International Nuclear Information System (INIS)

Shaposhnikov, M.V.; Moskalev, A.A.; Turysheva, E.V.

2007-01-01

Complete text of publication follows. The members of the heat shock proteins (Hsp) family function as molecular chaperones and assist intracellular folding of newly synthesized proteins. Also it is possible that molecular chaperones are induced during adaptive response to oxidative stress and radiation. The aim of our research was to exam the role of heat shock proteins in adaptive response to oxidative stress after low dose rate gamma-irradiation in Drosophila melanogaster. Drosophilamelanogaster strains were kindly provided by Bloomington Drosophila Stock Center (University of state of Indiana, Bloomington, USA). We used wild type strain (CS), heat shock protein mutant strains (Hsp22, Hsp70, Hsp83), and heat shock factor mutant strain (Hsf). Strains were chronically exposured to adaptive dose of gamma-irradiation in dose rate of 0.17 cGy/h during all stages of life history (from the embrional stage to the stage of matured imago). The rate of absorbed dose was 60 cGy. For oxidative-stress challenge twodays old flies were starved in empty vials for 6 h and then transferred to vials containing only filter paper soaked with 20 mM paraquat in 5% sucrose solution. Survival data were collected after 26 h of treatment. Dead flies were counted daily. The obtained data were subjected to survival analysis by Kaplan and Meier method and presented as survival curves. Statistical analysis was held by non-parametric methods. To test the significance of the difference between the two age distributions Kolmogorov-Smirnov test was applied. Gehan-Braslow- Wilcoxon and Cox-Mantel tests were used for estimation of median life span differences. In addition the minimal and maximal life span, time of 90% death, and mortality rate doubling time (MRDT) were estimated. The obtained results will be discussed in presentation.

A mathematical model resolving normal human blood lymphocyte population X-ray survival curves into six components: radiosensitivity, death rate and size of two responding sub-populations

International Nuclear Information System (INIS)

Thomson, A.E.R.; Vaughan-Smith, S.; Peel, W.E.

1982-01-01

The analysis was based on observations of survival decrease as a function of dose (range 0-5 Gy (= 500 rad)) and time after irradiation in vitro. Since lymphocyte survival is also sensitive to culture conditions the effects of radiation were examined daily up to 3 days only, while survival of control cells remained ca. 90 per cent. The time-dependent changes were resolved as the death rates (first-order governed) of lethally-hit cells (apparent survivors), so rendering these distinguishable from the morphologically identical, true (ultimate) survivors. For 12 blood donors the estimated dose permitting 37 per cent ultimate survival (D 37 value) averaged 0.72 +- 0.18 (SD) Gy for the more radiosensitive lymphocyte fraction and 2.50 +- 0.67 Gy for the less radiosensitive, each fraction proving homogeneously radiosensitive and the latter identifying substantially in kind with T-type (E-rosetting lymphocytes). The half-life of lethally-hit members of either fraction varied widely among the donors (ranges, 25-104 hours and 11-40 hours, respectively). Survival curves reconstructed by summating the numerical estimates of the six parameters according to the theoretical model closely matched those observed experimentally (ranged in multiple correlation coefficient, 0.9709-0.9994) for all donors). This signified the absence of any additional, totally radioresistant cell fraction. (author)

Pre-nebular Light Curves of SNe I

Energy Technology Data Exchange (ETDEWEB)

Arnett, W. David [Steward Observatory, University of Arizona, 933 N. Cherry Avenue, Tucson, AZ 85721 (United States); Fryer, Christopher [Los Alamos National Laboratory, Los Alamos, NM (United States); Matheson, Thomas [National Optical Astronomy Observatory, Tucson, AZ (United States)

2017-09-01

We compare analytic predictions of supernova light curves with recent high-quality data from SN2011fe (Ia), KSN2011b (Ia), and the Palomar Transient Factory and the La Silla-QUEST variability survey (LSQ) (Ia). Because of the steady, fast cadence of observations, KSN2011b provides unique new information on SNe Ia: the smoothness of the light curve, which is consistent with significant large-scale mixing during the explosion, possibly due to 3D effects (e.g., Rayleigh–Taylor instabilities), and provides support for a slowly varying leakage (mean opacity). For a more complex light curve (SN2008D, SN Ib), we separate the luminosity due to multiple causes and indicate the possibility of a radioactive plume. The early rise in luminosity is shown to be affected by the opacity (leakage rate) for thermal and non-thermal radiation. A general derivation of Arnett’s rule again shows that it depends upon all processes heating the plasma, not just radioactive ones, so that SNe Ia will differ from SNe Ibc if the latter have multiple heating processes.

Applied survival analysis using R

CERN Document Server

Moore, Dirk F

2016-01-01

Applied Survival Analysis Using R covers the main principles of survival analysis, gives examples of how it is applied, and teaches how to put those principles to use to analyze data using R as a vehicle. Survival data, where the primary outcome is time to a specific event, arise in many areas of biomedical research, including clinical trials, epidemiological studies, and studies of animals. Many survival methods are extensions of techniques used in linear regression and categorical data, while other aspects of this field are unique to survival data. This text employs numerous actual examples to illustrate survival curve estimation, comparison of survivals of different groups, proper accounting for censoring and truncation, model variable selection, and residual analysis. Because explaining survival analysis requires more advanced mathematics than many other statistical topics, this book is organized with basic concepts and most frequently used procedures covered in earlier chapters, with more advanced topics...

Study on minimum heat-flux point during boiling heat transfer on horizontal plates

International Nuclear Information System (INIS)

Nishio, Shigefumi

1985-01-01

The characteristics of boiling heat transfer are usually shown by the boiling curve of N-shape having the maximum and minimum points. As for the limiting heat flux point, that is, the maximum point, there have been many reports so far, as it is related to the physical burn of heat flux-controlling type heating surfaces. But though the minimum heat flux point is related to the quench point as the problems in steel heat treatment, the core safety of LWRs, the operational stability of superconducting magnets, the start-up characteristics of low temperature machinery, the condition of vapor explosion occurrence and so on, the systematic information has been limited. In this study, the effects of transient property and the heat conductivity of heating surfaces on the minimum heat flux condition in the pool boiling on horizontal planes were experimentally examined by using liquid nitrogen. The experimental apparatuses for steady boiling, for unsteady boiling with a copper heating surface, and for unsteady boiling with a heating surface other than copper were employed. The boiling curves obtained with these apparatuses and the minimum heat flux point condition are discussed. (Kako, I.)

Heat-treatment and heat-to-heat variations in the fracture toughness of Alloy 718

International Nuclear Information System (INIS)

Mills, W.J.

1981-07-01

The effect of heat-treatment and heat-to-heat variations on the J Ic fracture toughness response of Alloy 718 was examined at room and elevated temperatures using the multiple-specimen R-curve technique. Six heats of alloy 718 were tested in the conventional and modified heat-treated conditions. The fracture toughness response for the modified superalloy was found to be superior to that exhibited by the conventional material. Heat-to-heat variations in the J Ic response of Alloy 718 were observed in both heat-treated conditions; the modified treatment exhibited much larger variability. The J Ic and corresponding K Ic fracture toughness values were analyzed statistically to establish minimum expected toughness, values for use in design and safety analyses. 26 refs., 10 figs., 9 tabs

Design fatigue curve for Hastelloy-X

International Nuclear Information System (INIS)

Nishiguchi, Isoharu; Muto, Yasushi; Tsuji, Hirokazu

1983-12-01

In the design of components intended for elevated temperature service as the experimental Very High-Temperature gas-cooled Reactor (VHTR), it is essential to prevent fatigue failure and creep-fatigue failure. The evaluation method which uses design fatigue curves is adopted in the design rules. This report discussed several aspects of these design fatigue curves for Hastelloy-X (-XR) which is considered for use as a heat-resistant alloy in the VHTR. Examination of fatigue data gathered by a literature search including unpublished data showed that Brinkman's equation is suitable for the design curve of Hastelloy-X (-XR), where total strain range Δ epsilon sub(t) is used as independent variable and fatigue life Nsub(f) is transformed into log(log Nsub(f)). (author)

Influence on Heat Transfer Coefficient of Heat Exchanger by Velocity and Heat Transfer Temperature Difference

Directory of Open Access Journals (Sweden)

WANG Fang

2017-04-01

Full Text Available Aimed to insufficient heat transfer of heat exchanger, research the influence on the heat transfer coefficient impacted by velocity and heat transfer temperature difference of tube heat exchanger. According to the different heat transfer temperature difference and gas velocity，the experimental data were divided into group. Using the control variable method，the above two factors were analyzed separately. K一△T and k一:fitting curve were clone to obtain empirical function. The entire heat exchanger is as the study object，using numerical simulation methods，porous media，k一￡model，second order upwind mode，and pressure一velocity coupling with SIMPLE algorithm，the entire heat exchanger temperature field and the heat transfer coefficient distribution were given. Finally the trend of the heat transfer coefficient effected by the above two factors was gotten.

Heat transfer coefficients during quenching of steels

Energy Technology Data Exchange (ETDEWEB)

Hasan, H.S.; Jalil, J.M. [University of Technology, Department of Electromechanical Engineering, Baghdad (Iraq); Peet, M.J.; Bhadeshia, H.K.D.H. [University of Cambridge, Department of Materials Science and Metallurgy, Cambridge (United Kingdom)

2011-03-15

Heat transfer coefficients for quenching in water have been measured as a function of temperature using steel probes for a variety of iron alloys. The coefficients were derived from measured cooling curves combined with calculated heat-capacities. The resulting data were then used to calculate cooling curves using the finite volume method for a large steel sample and these curves have been demonstrated to be consistent with measured values for the large sample. Furthermore, by combining the estimated cooling curves with time-temperature-transformation (TTT) diagrams it has been possible to predict the variation of hardness as a function of distance via the quench factor analysis. The work should prove useful in the heat treatment of the steels studied, some of which are in the development stage. (orig.)

District heating grid of the Daqing Nuclear Heating Plant

Energy Technology Data Exchange (ETDEWEB)

Changwen, Ma [Institute of Nuclear Energy and Technology, Tsingua Univ., Beijing (China)

1997-09-01

The Daqing Nuclear Heating Plant is the first commercial heating plant to be built in China. The plant is planned to be used as the main heat resource of one residential quarter of Daqing city. The main parameters of the heating plant are summarized in the paper. The load curve shows that the capacity of the NHP is about 69% of total capacity of the grid. The 12 existing boilers can be used as reserve and peak load heat resources. Two patterns of load following have have been considered and tested on the 5MW Test Heating Reactor. Experiment shows load of heat grid is changed slowly, so automatic load following is not necessary. (author). 9 figs, 1 tab.

Dissolution and Precipitation Behaviour during Continuous Heating of Al–Mg–Si Alloys in a Wide Range of Heating Rates

Science.gov (United States)

Osten, Julia; Milkereit, Benjamin; Schick, Christoph; Kessler, Olaf

2015-01-01

In the present study, the dissolution and precipitation behaviour of four different aluminium alloys (EN AW-6005A, EN AW-6082, EN AW-6016, and EN AW-6181) in four different initial heat treatment conditions (T4, T6, overaged, and soft annealed) was investigated during heating in a wide dynamic range. Differential scanning calorimetry (DSC) was used to record heating curves between 20 and 600 °C. Heating rates were studied from 0.01 K/s to 5 K/s. We paid particular attention to control baseline stability, generating flat baselines and allowing accurate quantitative evaluation of the resulting DSC curves. As the heating rate increases, the individual dissolution and precipitation reactions shift to higher temperatures. The reactions during heating are significantly superimposed and partially run simultaneously. In addition, precipitation and dissolution reactions are increasingly suppressed as the heating rate increases, whereby exothermic precipitation reactions are suppressed earlier than endothermic dissolution reactions. Integrating the heating curves allowed the enthalpy levels of the different initial microstructural conditions to be quantified. Referring to time–temperature–austenitisation diagrams for steels, continuous heating dissolution diagrams for aluminium alloys were constructed to summarise the results in graphical form. These diagrams may support process optimisation in heat treatment shops.

Dissolution and Precipitation Behaviour during Continuous Heating of Al–Mg–Si Alloys in a Wide Range of Heating Rates

Directory of Open Access Journals (Sweden)

Julia Osten

2015-05-01

Full Text Available In the present study, the dissolution and precipitation behaviour of four different aluminium alloys (EN AW-6005A, EN AW-6082, EN AW-6016, and EN AW-6181 in four different initial heat treatment conditions (T4, T6, overaged, and soft annealed was investigated during heating in a wide dynamic range. Differential scanning calorimetry (DSC was used to record heating curves between 20 and 600 °C. Heating rates were studied from 0.01 K/s to 5 K/s. We paid particular attention to control baseline stability, generating flat baselines and allowing accurate quantitative evaluation of the resulting DSC curves. As the heating rate increases, the individual dissolution and precipitation reactions shift to higher temperatures. The reactions during heating are significantly superimposed and partially run simultaneously. In addition, precipitation and dissolution reactions are increasingly suppressed as the heating rate increases, whereby exothermic precipitation reactions are suppressed earlier than endothermic dissolution reactions. Integrating the heating curves allowed the enthalpy levels of the different initial microstructural conditions to be quantified. Referring to time–temperature–austenitisation diagrams for steels, continuous heating dissolution diagrams for aluminium alloys were constructed to summarise the results in graphical form. These diagrams may support process optimisation in heat treatment shops.

A numerical investigation of the effect of surface wettability on the boiling curve.

Directory of Open Access Journals (Sweden)

Hua-Yi Hsu

Full Text Available Surface wettability is recognized as playing an important role in pool boiling and the corresponding heat transfer curve. In this work, a systematic study of pool boiling heat transfer on smooth surfaces of varying wettability (contact angle range of 5° - 180° has been conducted and reported. Based on numerical simulations, boiling curves are calculated and boiling dynamics in each regime are studied using a volume-of-fluid method with contact angle model. The calculated trends in critical heat flux and Leidenfrost point as functions of surface wettability are obtained and compared with prior experimental and theoretical predictions, giving good agreement. For the first time, the effect of contact angle on the complete boiling curve is shown. It is demonstrated that the simulation methodology can be used for studying pool boiling and related dynamics and providing more physical insights.

Process and apparatus for indirect-fired heating and drying

Science.gov (United States)

Abbasi, Hamid Ali; Chudnovsky, Yaroslav

2005-04-12

A method for heating flat or curved surfaces comprising injecting fuel and oxidant along the length, width or longitudinal side of a combustion space formed between two flat or curved plates, transferring heat from the combustion products via convection and radiation to the surface being heated on to the material being dried/heated, and recirculating at least 20% of the combustion products to the root of the flame.

Survival curves of irradiated glutathione-deficient human fibroblasts: indication of a reduced enhancement of radiosensitivity by oxygen and misonidazole

International Nuclear Information System (INIS)

Midander, J.; Deschavanne, P.J.; Malaise, E.P.; Revesz, L.

1982-01-01

Fibroblasts derived from a patient with 5-oxoprolinuria are genetically deficient in glutathione synthetase. This deficiency causes a dramatic decrease in intracellular glutathione (GSH) level. The radiosensitivity of GSH deficient cells (GSH) was studied in vitro using colony forming ability as an endpoint. Cells with normal GSH level, obtained from the healthy brother of the patient, were used as controls. When irradiated in 95% air-5% CO 2 , GSH - cells are slightly but significantly more radiosensitive than GSH + controls (dose modifying factor (DMF) of 1.2). When irradiated in argon, the survival curve of GSH - cells indicates an oxygen enhancement ratio (OER) of 1.5 when compared to the curve obtained in oxic conditions. The OER of control cells in the same conditions is 2.9. In comparison to results obtained in air, 100% oxygen moderately increases the radiosensitivity of GSH + cells (DMF 1,23), while it has a very low effect on GSH - cells (DMF 1.06). These results suggest that intracellular GSH plays an essential protective role in hypoxia, its effect is reduced in air and practically disappears in 100% oxygen. When cells are incubated with 8 mM misonidazole 2 hours before irradiation, the drug has a much greater sensitizing effect on GSH + cells (DMF 2.33) than on GSH - cells (DMF 1.55). The results demonstrate that intracellular GSH level plays a major role in the response of hypoxic cells, irradiated either alone or in the presence of misonidazole

Influence of heat and radiation on the germinability and viability of B. cereus BIS-59 spores

International Nuclear Information System (INIS)

Kamat, A.S.; Lewis, N.F.

1983-01-01

Spores of Bicillus cereus BIS-59, isolated in this laboratory from shrimps, exhibited an exponential gamma radiation survival curve with a d 10 value of 400 krad as compared with a D 10 value of 30 krad for the vegetative cells. The D 10 value of DPA-depleted spores was also 400 krad indicating that DPA does not influence the radiation response of these spores. Maximum germination monitored with irradiated spores was 60 percent as compared with 80 percent in case of unirradiated spores. Radiation-induced inhibition of the germination processes was not dose dependent. Heat treatment (15 min at 80 C) to spores resulted in activation of the germination process; however, increase in heating time (30 min and 60 min) increased the germination lag period. DPA-depleted spores were less heat resistant than normal spores and exhibited biphasic exponential inactivation. (author)

Variation in resistance of natural isolates of Staphylococcus aureus to heat, pulsed electric field and ultrasound under pressure.

Science.gov (United States)

Rodríguez-Calleja, J M; Cebrián, G; Condón, S; Mañas, P

2006-05-01

To study and compare the resistance of 15 Staphylococcus aureus isolates to heat, pulsed electric field (PEF) and ultrasound (UW) under pressure (manosonication, MS). Survival curves to heat (58 degrees C), to PEF (22 kV cm(-1), 2 micros square wave pulses) and to UW under pressure (117 microm, 20 kHz, 200 kPa) were obtained and inactivation parameters (decimal reduction times for heat and UW under pressure, and b-values for PEF) were calculated. A wide resistance variation to heat treatment, but not to PEF and MS, was observed amongst the 15 strains. There was no relationship between the resistances to the three physical agents studied. Staphylococcus aureus was relatively resistant to MS but sensitive to PEF. Heat resistance varied with strain and was positively correlated to carotenoid pigment content. Results would help in defining safe food preservation processes. Care should be taken to choose the most adequate strain of S. aureus to model food preservation processing.

Critical behaviour of binary mixture of {xC6H5CN + (1 - x)CH3(CH2)7CH3}: Measurements of coexistence curves, light scattering, and heat capacity

International Nuclear Information System (INIS)

Lei Yuntao; Chen Zhiyun; Wang Nong; Mao Chunfeng; An Xueqin; Shen Weiguo

2010-01-01

Liquid + liquid coexistence, light scattering, and isobaric heat capacity per unit volume for the critical solutions of (benzonitrile + n-nonane) have been measured. The critical exponents relating to the coexistence curve β, the osmotic compressibility γ, the correlation length ν, and the heat capacity α have been deduced and the values are consistent with the 3D-Ising values in the range close to the critical point. The experimental results of the liquid + liquid coexistence were analyzed to examine the Wegner correction terms and the behaviour of the diameter of the coexistence curves. The light scattering data were well described by the crossover model proposed by Anisimov and Sengers, and showed a tendency of monotonic crossover of the critical exponents γ and ν from the 3D-Ising values to the mean-field values as the temperature departures from the critical point. From calorimetric measurements, the amplitude A ± and the critical background B cr of the heat capacity in the critical region have been deduced and some universal ratios are tested.

Ensemble of cell survival experiments after ion irradiation for validation of RBE models

Energy Technology Data Exchange (ETDEWEB)

Friedrich, Thomas; Scholz, Uwe; Scholz, Michael [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Durante, Marco [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany); Institut fuer Festkoerperphysik, TU Darmstadt, Darmstadt (Germany)

2012-07-01

There is persistent interest in understanding the systematics of the relative biological effectiveness (RBE). Models such as the Local Effect Model (LEM) or the Microdosimetric Kinetic Model have the goal to predict the RBE. For the validation of these models a collection of many in-vitro cell survival experiments is most appropriate. The set-up of an ensemble of in-vitro cell survival data comprising about 850 survival experiments after both ion and photon irradiation is reported. The survival curves have been taken out from publications. The experiments encompass survival curves obtained in different labs, using different ion species from protons to uranium, varying irradiation modalities (shaped or monoenergetic beam), various energies and linear energy transfers, and a whole variety of cell types (human or rodent; normal, mutagenic or tumor; radioresistant or -sensitive). Each cell survival curve has been parameterized by the linear-quadratic model. The photon parameters have been added to the data base to allow to calculate the experimental RBE to any survival level. We report on experimental trends found within the data ensemble. The data will serve as a testing ground for RBE models such as the LEM. Finally, a roadmap for further validation and first model results using the data base in combination with the LEM are presented.

Generalization of drying curves in conductive/convective drying of cellulose

Directory of Open Access Journals (Sweden)

M. Stenzel

2003-03-01

Full Text Available The objective of this work is to analyze the possibility of applying the drying curves generalization methodology to the conductive/convective hot plate drying of cellulose. The experiments were carried out at different heated plate temperatures and air velocities over the surface of the samples. This kind of approach is very interesting because it permits comparison of the results of different experiments by reducing them to only one set, which can be divided into two groups: the generalized drying curves and the generalized drying rate curves. The experimental apparatus is an attempt to reproduce the operational conditions of conventional paper dryers (ratio of paper/air movement and consists of a metallic box heated by a thermostatic bath containing an upper surface on which the cellulose samples are placed. Sample material is short- and long-fiber cellulose sheets, about 1 mm thick, and ambient air was introduced into the system by a adjustable blower under different conditions. Long-fiber cellulose generalized curves were obtained and analyzed first individually and then together with the short-fiber cellulose results from Motta Lima et al. (2000 a,b. Finally, a set of equations to fit the generalized curves obtained was proposed and discussed.

A statistical method for estimating wood thermal diffusivity and probe geometry using in situ heat response curves from sap flow measurements.

Science.gov (United States)

Chen, Xingyuan; Miller, Gretchen R; Rubin, Yoram; Baldocchi, Dennis D

2012-12-01

The heat pulse method is widely used to measure water flux through plants; it works by using the speed at which a heat pulse is propagated through the system to infer the velocity of water through a porous medium. No systematic, non-destructive calibration procedure exists to determine the site-specific parameters necessary for calculating sap velocity, e.g., wood thermal diffusivity and probe spacing. Such parameter calibration is crucial to obtain the correct transpiration flux density from the sap flow measurements at the plant scale and subsequently to upscale tree-level water fluxes to canopy and landscape scales. The purpose of this study is to present a statistical framework for sampling and simultaneously estimating the tree's thermal diffusivity and probe spacing from in situ heat response curves collected by the implanted probes of a heat ratio measurement device. Conditioned on the time traces of wood temperature following a heat pulse, the parameters are inferred using a Bayesian inversion technique, based on the Markov chain Monte Carlo sampling method. The primary advantage of the proposed methodology is that it does not require knowledge of probe spacing or any further intrusive sampling of sapwood. The Bayesian framework also enables direct quantification of uncertainty in estimated sap flow velocity. Experiments using synthetic data show that repeated tests using the same apparatus are essential for obtaining reliable and accurate solutions. When applied to field conditions, these tests can be obtained in different seasons and can be automated using the existing data logging system. Empirical factors are introduced to account for the influence of non-ideal probe geometry on the estimation of heat pulse velocity, and are estimated in this study as well. The proposed methodology may be tested for its applicability to realistic field conditions, with an ultimate goal of calibrating heat ratio sap flow systems in practical applications.

Survival and Virulence of Campylobacter spp. in the Environment

DEFF Research Database (Denmark)

Bui, Thanh Xuan

of environmental stress factors, namely heat shock, starvation, osmosis, and oxidation, on the expression of three virulence genes (ciaB, dnaJ, and htrA) of C. jejuni and its uptake by and intracellular survival within A. castellanii. I also investigated the mechanism(s) involved in phagocytosis and killing of C....... jejuni by A. castellanii. I observed that heat and osmotic stresses reduced the survival of C. jejuni significantly, whereas oxidative stress had no effect. The results of qRT-PCR experiments showed that the transcription of virulence genes of C. jejuni was slightly up-regulated under heat and oxidative...... soil flagellates may play a role for the survival of these food-borne pathogens on plant surfaces and in soil. It would be very interesting to further investigate the impacts of this soil flagellate on the survival of different food-borne pathogens in soil and in plant surface that may explain...

Radiant absorption characteristics of corrugated curved tubes

Directory of Open Access Journals (Sweden)

Đorđević Milan Lj.

2017-01-01

Full Text Available The utilization of modern paraboloidal concentrators for conversion of solar radiation into heat energy requires the development and implementation of compact and efficient heat absorbers. Accurate estimation of geometry influence on absorption characteristics of receiver tubes is an important step in this process. This paper deals with absorption characteristics of heat absorber made of spirally coiled tubes with transverse circular corrugations. Detailed 3-D surface-to-surface Hemicube method was applied to compare radiation performances of corrugated and smooth curved tubes. The numerical results were obtained by varying the tube curvature ratio and incident radiant heat flux intensity. The details of absorption efficiency of corrugated tubes and the effect of curvature on absorption properties for both corrugated and smooth tubes were presented. The results may have significance to further analysis of highly efficient heat absorbers exposed to concentrated radiant heating. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 42006

Culture conditions affecting the survival response of Chinese hamster ovary cells treated by hyperthermia

International Nuclear Information System (INIS)

Highfield, D.P.; Holahan, E.V.; Dewey, W.C.

1982-01-01

Using lethally irradiated feeder cells to control cell population densities, researchers investigated the survival of Chinese hamster ovary cells heated between 42.2 and 45.5 degrees C. Test cells were plated into T25 flasks with or without feeder cells, incubated 2 hours at 37 degrees C, and then given various heat treatments. Under all heating conditions, survival increased in those flasks containing feeder cells. Increased survival (by as much as a factor of 100 for cells heated at 42.4 degrees C for 6-10 hr) was most apparent when cells were heated to thermotolerance. By adjustment of test and feeder cell numbers, survival increased as density increased; however, maximum survival followed a transition period that occurred between the plating of 1 X 10(4) and 6 X 10(4) cells. Experimental artifacts due to improper control of cell density was demonstrated

Singular interactions supported by embedded curves

International Nuclear Information System (INIS)

Kaynak, Burak Tevfik; Turgut, O Teoman

2012-01-01

In this work, singular interactions supported by embedded curves on Riemannian manifolds are discussed from a more direct and physical perspective, via the heat kernel approach. We show that the renormalized problem is well defined, the ground state is finite and the corresponding wavefunction is positive. The renormalization group invariance of the model is also discussed. (paper)

Intracellular contacts - effect of survival curve of mammal cells on the Dq value

International Nuclear Information System (INIS)

Durand, R.E.; Sutherland, R.M.

1980-01-01

Survival increase is observed in cells of the Chinese hamster of the V79-171 line which grow in the composition of multicell spheroids as compared with the survival after irradiation in a single state. The ratio of the Dsub(q) cell value in the composition of spheroids to Dsub(q) of separately growing cells increases as the mitotic cycle proceeds from the minimum value of 1.3 for cells in the Gi phase to the maximum value of 2.2 for cells in a late S-phase. The increase of survival during growth in the composition of spheroids is not characteristic for all cell types. Only a part of cultured MNNG-mutants of cells of the V79-171 Chinese hamster reveal radiomodifying effect of cell contact acting [ru

New graphic AUC-based method to estimate overall survival benefit: pomalidomide reanalysis.

Science.gov (United States)

Fenix-Caballero, S; Diaz-Navarro, J; Prieto-Callejero, B; Rios-Sanchez, E; Alegre-del Rey, E J; Borrero-Rubio, J M

2016-02-01

Difference in median survival is an erratic measure and sometimes does not provide a good assessment of survival benefit. The aim of this study was to reanalyse the overall survival benefit of pomalidomide from pivotal clinical trial using a new area under curve (AUC)-based method. In the pivotal trial, pomalidomide plus low-dose dexamethasone showed a significant survival benefit over high-dose dexamethasone, with a difference between medians of 4.6 months. The new AUC method applied to the survival curves, obtained an overall survival benefit of 2.6 months for the pomalidomide treatment. This average difference in OS was calculated for the 61.5% of patients for whom the time to event is reliable enough. This 2-month differential would have major clinical and pharmacoeconomic implications, on both cost-effectiveness studies and on the willingness of the healthcare systems to pay for this treatment. © 2015 John Wiley & Sons Ltd.

Survival and mortality among users and non-users of hydroxyurea with sickle cell disease.

Science.gov (United States)

de Araujo, Olinda Maria Rodrigues; Ivo, Maria Lúcia; Ferreira Júnior, Marcos Antonio; Pontes, Elenir Rose Jardim Cury; Bispo, Ieda Maria Gonçalves Pacce; de Oliveira, Eveny Cristine Luna

2015-01-01

to estimate survival, mortality and cause of death among users or not of hydroxyurea with sickle cell disease. cohort study with retrospective data collection, from 1980 to 2010 of patients receiving inpatient treatment in two Brazilian public hospitals. The survival probability was determined using the Kaplan-Meier estimator, survival calculations (SPSS version 10.0), comparison between survival curves, using the log rank method. The level of significance was p=0.05. of 63 patients, 87% had sickle cell anemia, with 39 using hydroxyurea, with a mean time of use of the drug of 20.0±10.0 years and a mean dose of 17.37±5.4 to 20.94±7.2 mg/kg/day, raising the fetal hemoglobin. In the comparison between those using hydroxyurea and those not, the survival curve was greater among the users (p=0.014). A total of 10 deaths occurred, with a mean age of 28.1 years old, and with Acute Respiratory Failure as the main cause. the survival curve is greater among the users of hydroxyurea. The results indicate the importance of the nurse incorporating therapeutic advances of hydroxyurea in her care actions.

Survival of Patients With Cervical Cancer in Rural India

OpenAIRE

Vinoda Thulaseedharan, Jissa; Malila, Nea; Swaminathan, Rajaraman; Esmy Pulikottil, Okuru; Hakama, Matti; Muwonge, Richard; Sankaranarayanan, Rengaswamy

2015-01-01

Background: Patients’ survival after diagnosis of cervical cancer is indirectly influenced by socio-economic factors. We evaluated this survival and its socio-economic determinants in a rural population in south India. Methods: We assessed 165 women diagnosed with cervical cancer from the routine care control arm of a randomized screening trial conducted in rural south India. Kaplan-Meier curves were plotted to illustrate the observed survival of cancer patients. The effect of socio-econom...

Cooling Curve of Strange Star in Strong Magnetic Field

Institute of Scientific and Technical Information of China (English)

WANG Xiao-Qin; LUO Zhi-Quan

2008-01-01

In this paper, firstly, we investigate the neutrino emissivity from quark Urca process in strong magnetic field. Then, we discuss the heat capacity of strange stars in strong magnetic field. Finally, we give the cooling curve in strong magnetic field. In order to make a comparison, we also give the corresponding cooling curve in the case of null magnetic field. It turns out that strange stars cool faster in strong magnetic field than that without magnetic field.

Rationalization in architecture with surfaces foliated by elastic curves

DEFF Research Database (Denmark)

Nørbjerg, Toke Bjerge

analytic form using elliptic functions. We use a gradient-driven optimization to approximate arbitrary planar curves by planar elastic curves. The method depends on an explicit parameterization of the space of elastic curves and on a method for finding a good initial guess for the optimization. We......We develop methods for rationalization of CAD surfaces using elastic curves, aiming at a costeffective fabrication method for architectural designs of complex shapes. By moving a heated flexible metal rod though a block of expanded polystyrene, it is possible to produce shapes with both positive...... and negative Gaussian curvature, either for direct use or for use as moulds for concrete casting. If we can control the shape of the rod, while moving, we can produce prescribed shapes. The flexible rod assumes at all times the shape of an Euler elastica (or elastic curve). The elastica are given in closed...

Using Survival Analysis to Evaluate Medical Equipment Battery Life.

Science.gov (United States)

Kuhajda, David

2016-01-01

As hospital medical device managers obtain more data, opportunities exist for using the data to improve medical device management, enhance patient safety, and evaluate costs of decisions. As a demonstration of the ability to use data analytics, this article applies survival analysis statistical techniques to assist in making decisions on medical equipment maintenance. The analysis was performed on a large amount of data related to failures of an infusion pump manufacturer's lithium battery and two aftermarket replacement lithium batteries from one hospital facility. The survival analysis resulted in statistical evidence showing that one of the third-party batteries had a lower survival curve than the infusion pump manufacturer's battery. This lower survival curve translates to a shorter expected life before replacement is needed. The data suggested that to limit unexpected failures, replacing batteries at a two-year interval, rather than the current industry recommendation of three years, may be warranted. For less than $5,400 in additional annual cost, the risk of unexpected battery failures can be reduced from an estimated 28% to an estimated 7%.

Glow curve characteristics of bulb type thermoluminescent dosimeters

International Nuclear Information System (INIS)

Deme, S.; Feher, I.; Felszerfalvi, J.

1993-01-01

TL dosemeter readers are equipped usually with thermocouples connected to the heater unit. This layout can well be applied to stabilize the position of the glow curve as a function of heating-up time. Bulb type TL dosemeters do not have temperature sensors, no possibility for stabilization, which can cause an additional readout error of dose determination. For this reason, the time dependence of glow curves for bulb-type TL dosemeters was measured, and a new microprocessor controlled readout device was developed. (N.T.) 2 refs.; 2 figs

Coupling heat and chemical tracer experiments for estimating heat transfer parameters in shallow alluvial aquifers.

Science.gov (United States)

Wildemeersch, S; Jamin, P; Orban, P; Hermans, T; Klepikova, M; Nguyen, F; Brouyère, S; Dassargues, A

2014-11-15

Geothermal energy systems, closed or open, are increasingly considered for heating and/or cooling buildings. The efficiency of such systems depends on the thermal properties of the subsurface. Therefore, feasibility and impact studies performed prior to their installation should include a field characterization of thermal properties and a heat transfer model using parameter values measured in situ. However, there is a lack of in situ experiments and methodology for performing such a field characterization, especially for open systems. This study presents an in situ experiment designed for estimating heat transfer parameters in shallow alluvial aquifers with focus on the specific heat capacity. This experiment consists in simultaneously injecting hot water and a chemical tracer into the aquifer and monitoring the evolution of groundwater temperature and concentration in the recovery well (and possibly in other piezometers located down gradient). Temperature and concentrations are then used for estimating the specific heat capacity. The first method for estimating this parameter is based on a modeling in series of the chemical tracer and temperature breakthrough curves at the recovery well. The second method is based on an energy balance. The values of specific heat capacity estimated for both methods (2.30 and 2.54MJ/m(3)/K) for the experimental site in the alluvial aquifer of the Meuse River (Belgium) are almost identical and consistent with values found in the literature. Temperature breakthrough curves in other piezometers are not required for estimating the specific heat capacity. However, they highlight that heat transfer in the alluvial aquifer of the Meuse River is complex and contrasted with different dominant process depending on the depth leading to significant vertical heat exchange between upper and lower part of the aquifer. Furthermore, these temperature breakthrough curves could be included in the calibration of a complex heat transfer model for

The statistical treatment of cell survival data

International Nuclear Information System (INIS)

Boag, J.W.

1975-01-01

The paper considers the sources of experimental error in cell survival experiments and discusses in simple terms how these combine to influence the accuracy of single points and the parameters of complete survival curves. Cell sampling and medium-dilution errors are discussed at length and one way of minimizing the former is examined. The Monte-Carlo method of estimating the distribution of derived parameters in small samples is recommended and illustrated. (author)

Optical and IR light curves of VV Puppis

International Nuclear Information System (INIS)

Szkody, P.; Bailey, J.A.; Hough, J.H.

1983-01-01

We present optical (0.36 to 0.6 μm) light curves with time resolutions of seconds and infrared (IR) (1.25 to 2.2 μm) light curves with time resolutions of minutes for VV Puppis during a high state. The optical light curves show a single hump with largest amplitude in the V filter, while the IR light curves show a double hump sinusoidal variation. Flickering is evident in both the optical and IR light curves, with the largest amplitude in optical B light. Through subtraction of the low state fluxes from our high state values, we obtain a flux distribution of the accretion column which peaks at 0.55 μm and becomes #betta# 2 in the IR, consistent with current cyclotron models. Comparison of the observed IR variations throughout the orbit with the expected variations due to an M4 star heated by an accretion column at an inclination of 66 0 suggests that the IR light is a combination of the secondary star plus contributions from two emitting poles. (author)

Optimal assignment of multiple utilities in heat exchange networks

International Nuclear Information System (INIS)

Salama, A.I.A.

2009-01-01

Existing numerical geometry-based techniques, developed by [A.I.A. Salama, Numerical techniques for determining heat energy targets in pinch analysis, Computers and Chemical Engineering 29 (2005) 1861-1866; A.I.A. Salama, Determination of the optimal heat energy targets in heat pinch analysis using a geometry-based approach, Computers and Chemical Engineering 30 (2006) 758-764], have been extended to optimally assign multiple utilities in heat exchange network (HEN). These techniques utilize the horizontal shift between the cold composite curve (CC) and the stationary hot CC to determine the HEN optimal energy targets, grand composite curve (GCC), and the complement grand composite curve (CGCC). The proposed numerical technique developed in this paper is direct and simultaneously determines the optimal heat-energy targets and optimally assigns multiple utilities as compared with an existing technique based on sequential assignment of multiple utilities. The technique starts by arranging in an ascending order the HEN stream and target temperatures, and the resulting set is labelled T. Furthermore, the temperature sets where multiple utilities are introduced are arranged in an ascending order and are labelled T ic and T ih for the cold and hot sides, respectively. The graphical presentation of the results is facilitated by the insertion at each multiple-utility temperature a perturbed temperature equals the insertion temperature minus a small perturbation. Furthermore, using the heat exchanger network (HEN) minimum temperature-differential approach (ΔT min ) and stream heat-capacity flow rates, the presentation is facilitated by using the conventional temperature shift of the HEN CCs. The set of temperature-shifted stream and target temperatures and perturbed temperatures in the overlap range between the CCs is labelled T ol . Using T ol , a simple formula employing enthalpy-flow differences between the hot composite curve CC h and the cold composite curve CC c is

Targeting the maximum heat recovery for systems with heat losses and heat gains

International Nuclear Information System (INIS)

Wan Alwi, Sharifah Rafidah; Lee, Carmen Kar Mun; Lee, Kim Yau; Abd Manan, Zainuddin; Fraser, Duncan M.

2014-01-01

Graphical abstract: Illustration of heat gains and losses from process streams. - Highlights: • Maximising energy savings through heat losses or gains. • Identifying location where insulation can be avoided. • Heuristics to maximise heat losses or gains. • Targeting heat losses or gains using the extended STEP technique and HEAT diagram. - Abstract: Process Integration using the Pinch Analysis technique has been widely used as a tool for the optimal design of heat exchanger networks (HENs). The Composite Curves and the Stream Temperature versus Enthalpy Plot (STEP) are among the graphical tools used to target the maximum heat recovery for a HEN. However, these tools assume that heat losses and heat gains are negligible. This work presents an approach that considers heat losses and heat gains during the establishment of the minimum utility targets. The STEP method, which is plotted based on the individual, as opposed to the composite streams, has been extended to consider the effect of heat losses and heat gains during stream matching. Several rules to guide the proper location of pipe insulation, and the appropriate procedure for stream shifting have been introduced in order to minimise the heat losses and maximise the heat gains. Application of the method on two case studies shows that considering heat losses and heat gains yield more realistic utility targets and help reduce both the insulation capital cost and utility cost of a HEN

Explosions and light curves of supernovae

International Nuclear Information System (INIS)

Gaffet, B.

1975-01-01

The models developed to explain supernovae explosions are reviewed. The first one is thermonuclear explosion (simple or preceded by an implosion phase); the neutrino emission which results of such an explosion can have an important dynamical effect, according as the star is opaque or transparent to them; another theory involves the radiation pressure of the pulsar which is formed in the center of the star. The origin of the supernovae brightness is also uncertain: the initial heat due to the explosion does not seem to be sufficient; the brightness can result from the diffusion of the heat through the ejected matter or can be transported more rapidly by a shock wave. A model in which the heat is produced by the pulsar seems compatible with most observations (shapes of the brightness curves and the continuum spectra, expansion velocities, temperature and luminosity at the peak, total kinetic energy) [fr

Hyperthermic radiosensitization of synchronous Chinese hamster cells: relationship between lethality and chromosomal aberrations

International Nuclear Information System (INIS)

Dewey, W.C.; Sapareto, S.A.; Betten, D.A.

1978-01-01

Synchronous Chinese hamster cells in vitro were obtained by mitotic selection. The cells were heated at 45.5 0 C for 4 min in mitosis, 11 min in G 1 , or 7 min in S sphase and then x-irradiated immediately thereafter. Colony survival from heat alone was 0.30 to 0.45, and the frequency of chromosomal aberrations induced by heat was 0.00, 0.14, or 0.97 for heat treatments during M, G 1 , or S, respectively. As shown previously, lethality from hyperthermia alone is due to chromosomal aberrations only when the cells are heated during S phase. The log survival (D 0 /sup approximately/ = 80 rad) and aberration frequency curves for cells irradiated during mitosis were linear, and the only effect of hyperthermia was to shift the curves in accord with the effect from heat alone. Thus, hyperthermia did not radiosensitize the mitotic cells. The cells irradiated in G 1 were more resistant (D 0 /sup approximately/ = 100 rad) than those irradiated in mitosis, and the survival and aberration frequency curves both had shoulders. The primary effect of hyperthermia was to greatly reduce the shoulders of the curves and to increase the slopes by about 23%. The cells irradiated in S were the most resistant (D 0 /sup approximately/ = 140 rad), and the survival and aberration frequency curves both had large shoulders. For both end points of lethality and chromosomal aberrations, heat selectively radiosensitized S-phase cells relative to G 1 cells by removing most of the shoulder and increasing the slope by about 45%. For cells treated in G 1 or S, the increase in radiosensitization following hyperthermia can be accounted for by an increase in the frequency of chromosomal aberrations

Single-dose-response curves of murine gastrointestinal crypt stem cells

International Nuclear Information System (INIS)

Masuda, K.; Withers, H.R.; Mason, K.A.; Chen, K.Y.

1977-01-01

Dose-response curves for the reproductive capacity of crypt stem cells of murine colonic, jejunal, and gastric mucosae exposed in situ to multifractionated gamma ray exposures were analyzed and single-dose-survival curves of these cells were constructed. The following conclusions were drawn: (1) The single-dose-response curves bend downward over a dose range of approximately 200 to 1500 rad; (2) cell death seems to be due to nonrepairable damage at doses less than 250 rad for colon, and 220 rad for jejunum; (3) there are 21, 110, and 140 stem cells per crypt of gastric, colonic, and jejunal mucosa, respectively; and (4) jejunal stem cells are the most radiosensitive and gastric mucosal stem cells are the most resistant

Why the Kantian ideal survives medical learning curves, and why it matters.

Science.gov (United States)

Brecher, B

2006-09-01

The "Kantian ideal" is often misunderstood as invoking individual autonomy rather than rational self legislation. Le Morvan and Stock's otherwise insightful discussion of "Medical learning curves and the Kantian ideal"--for example--draws the mistaken inference that that ideal is inconsistent with the realities of medical practice. But it is not. Rationally to be a patient entails accepting its necessary conditions.

High-heat-flux testing of helium-cooled heat exchangers for fusion applications

International Nuclear Information System (INIS)

Youchison, D.L.; Izenson, M.G.; Baxi, C.B.; Rosenfeld, J.H.

1996-01-01

High-heat-flux experiments on three types of helium-cooled divertor mock-ups were performed on the 30-kW electron beam test system and its associated helium flow loop at Sandia National Laboratories. A dispersion-strengthened copper alloy (DSCu) was used in the manufacture of all the mock-ups. The first heat exchanger provides for enhanced heat transfer at relatively low flow rates and much reduced pumping requirements. The Creare sample was tested to a maximum absorbed heat flux of 5.8 MW/m 2 . The second used low pressure drops and high mass flow rates to achieve good heat removal. The GA specimen was tested to a maximum absorbed heat flux of 9 MW/m 2 while maintaining a surface temperature below 400 degree C. A second experiment resulted in a maximum absorbed heat flux of 34 MW/m 2 and surface temperatures near 533 degree C. The third specimen was a DSCu, axial flow, helium-cooled divertor mock-up filled with a porous metal wick which effectively increases the available heat transfer area. Low mass flow and high pressure drop operation at 4.0 MPa were characteristic of this divertor module. It survived a maximum absorbed heat flux of 16 MW/m 2 and reached a surface temperature of 740 degree C. Thermacore also manufactured a follow-on, dual channel porous metal-type heat exchanger, which survived a maximum absorbed heat flux of 14 MW/m 2 and reached a maximum surface temperature of 690 degree C. 11refs., 20 figs., 3 tabs

Adjuvant Medications That Improve Survival after Locoregional Therapy.

Science.gov (United States)

Boas, F Edward; Ziv, Etay; Yarmohammadi, Hooman; Brown, Karen T; Erinjeri, Joseph P; Sofocleous, Constantinos T; Harding, James J; Solomon, Stephen B

2017-07-01

To determine if outpatient medications taken at the time of liver tumor embolization or ablation affect survival. A retrospective review was done of 2,032 liver tumor embolization, radioembolization, and ablation procedures performed in 1,092 patients from June 2009 to April 2016. Pathology, hepatocellular carcinoma (HCC) stage (American Joint Committee on Cancer), neuroendocrine tumor (NET) grade, initial locoregional therapy, overall survival after initial locoregional therapy, Child-Pugh score, Eastern Cooperative Oncology Group performance status, Charlson Comorbidity Index, and outpatient medications taken at the time of locoregional therapy were analyzed for each patient. Kaplan-Meier survival curves were calculated for patients taking 29 medications or medication classes (including prescription and nonprescription medications) for reasons unrelated to their primary cancer diagnosis. Kaplan-Meier curves were compared using the log-rank test. For patients with HCC initially treated with embolization (n = 304 patients), the following medications were associated with improved survival when taken at the time of embolization: beta-blockers (P = .0007), aspirin (P = .0008) and other nonsteroidal antiinflammatory drugs (P = .009), proton pump inhibitors (P = .004), and antivirals for hepatitis B or C (P = .01). For colorectal liver metastases initially treated with ablation (n = 172 patients), beta-blockers were associated with improved survival when taken at the time of ablation (P = .02). Aspirin and beta-blockers are associated with significantly improved survival when taken at the time of embolization for HCC. Aspirin was not associated with survival differences after locoregional therapy for NET or colorectal liver metastases, suggesting an HCC-specific effect. Copyright © 2017 SIR. Published by Elsevier Inc. All rights reserved.

Probabilistic evaluation of design S-N curve and reliability assessment of ASME code-based evaluation

International Nuclear Information System (INIS)

Zhao Yongxiang

1999-01-01

A probabilistic evaluating approach of design S-N curve and a reliability assessment approach of the ASME code-based evaluation are presented on the basis of Langer S-N model-based P-S-N curves. The P-S-N curves are estimated by a so-called general maximum likelihood method. This method can be applied to deal with the virtual stress amplitude-crack initial life data which have a characteristics of double random variables. Investigation of a set of the virtual stress amplitude-crack initial life (S-N) data of 1Cr18Ni9Ti austenitic stainless steel-welded joint reveals that the P-S-N curves can give a good prediction of scatter regularity of the S-N data. Probabilistic evaluation of the design S-N curve with 0.9999 survival probability has considered various uncertainties, besides of the scatter of the S-N data, to an appropriate extent. The ASME code-based evaluation with 20 reduction factor on the mean life is much more conservative than that with 2 reduction factor on the stress amplitude. Evaluation of the latter in 666.61 MPa virtual stress amplitude is equivalent to 0.999522 survival probability and in 2092.18 MPa virtual stress amplitude equivalent to 0.9999999995 survival probability. This means that the evaluation in the low loading level may be non-conservative and in contrast, too conservative in the high loading level. Cause is that the reduction factors are constants and the factors can not take into account the general observation that scatter of the N data increases with the loading level decreasing. This has indicated that it is necessary to apply the probabilistic approach to the evaluation of design S-N curve

Boiling and burnout phenomena under transient heat input, 1

International Nuclear Information System (INIS)

Aoki, Shigebumi; Kozawa, Yoshiyuki; Iwasaki, Hideaki.

1976-01-01

In order to simulate the thermo-hydrodynamic conditions at reactor power excursions, a test piece was placed in a forced convective channel and heated with exponential power inputs. The boiling heat transfer and the burnout heat flux under the transient heat input were measured, and pressure and water temperature changes in the test section were recorded at the same time. Following experimental results were obtained; (1) Transient boiling heat transfer characteristics at high heat flux stayed on the stationary nucleate boiling curve of each flow condition, or extrapolated line of the curves. (2) Transient burnout heat flux increased remarkably with decreasing heating-time-constant, when the flow rate was lower and the subcooling was higher. (3) Transient burnout phenomena were expressed with the relation of (q sub(max) - q sub(sBO)) tau = constant at several flow conditions. This relation was derived from the stationary burnout mechanism of pool boiling. (auth.)

Technical report. The application of probability-generating functions to linear-quadratic radiation survival curves.

Science.gov (United States)

Kendal, W S

2000-04-01

To illustrate how probability-generating functions (PGFs) can be employed to derive a simple probabilistic model for clonogenic survival after exposure to ionizing irradiation. Both repairable and irreparable radiation damage to DNA were assumed to occur by independent (Poisson) processes, at intensities proportional to the irradiation dose. Also, repairable damage was assumed to be either repaired or further (lethally) injured according to a third (Bernoulli) process, with the probability of lethal conversion being directly proportional to dose. Using the algebra of PGFs, these three processes were combined to yield a composite PGF that described the distribution of lethal DNA lesions in irradiated cells. The composite PGF characterized a Poisson distribution with mean, chiD+betaD2, where D was dose and alpha and beta were radiobiological constants. This distribution yielded the conventional linear-quadratic survival equation. To test the composite model, the derived distribution was used to predict the frequencies of multiple chromosomal aberrations in irradiated human lymphocytes. The predictions agreed well with observation. This probabilistic model was consistent with single-hit mechanisms, but it was not consistent with binary misrepair mechanisms. A stochastic model for radiation survival has been constructed from elementary PGFs that exactly yields the linear-quadratic relationship. This approach can be used to investigate other simple probabilistic survival models.

Heat transport as torsional responses and Keldysh formalism in a curved spacetime

OpenAIRE

Shitade, Atsuo

2013-01-01

We revisit a theory of heat transport in the light of a gauge theory of gravity and find the proper heat current with a corresponding gauge field, which yields the natural definitions of the heat magnetization and the Kubo-formula contribution to the thermal conductivity as torsional responses. We also develop a general framework for calculating gravitational responses by combining the Keldysh and Cartan formalisms. By using this framework, we explicitly calculate these two quantities and rep...

Impact of Heat Shock Protein A 12B Overexpression on Spinal Astrocyte Survival Against Oxygen-Glucose-Serum Deprivation/Restoration in Primary Cultured Astrocytes.

Science.gov (United States)

Xia, Xun; Ma, Yuan; Yang, Li-Bin; Cheng, Jing-Ming; Yang, Tao; Fan, Ke-Xia; Li, Yun-Ming; Liu, En-Yu; Cheng, Lin; Huang, Hai-Dong; Gu, Jian-Wen; Kuang, Yong-Qin

2016-08-01

Heat shock protein A 12B (HSPA12B) is a newly discovered member of the heat shock protein 70 family. Preclinical evidence indicates that HSPA12B helps protect the brain from ischemic injury, although its specific function remains unclear. The aim of this study is to investigate whether HSPA12B overexpression can protect astrocytes from oxygen-glucose-serum deprivation/restoration (OGD/R) injury. We analyzed the effects of HSPA12B overexpression on spinal cord ischemia-reperfusion injury and spinal astrocyte survival. After ischemia-reperfusion injury, we found that HSPA12B overexpression decreased spinal cord water content and infarct volume. MTT assay showed that HSPA12B overexpression increased astrocyte survival after OGD/R treatment. Flow cytometry results showed a marked inhibition of OGD/R-induced astrocyte apoptosis. Western blot assay showed that HSPA12B overexpression significantly increased regulatory protein B-cell lymphocyte 2 (Bcl-2) levels, whereas it decreased expression of the Bax protein, which forms a heterodimer with Bcl-2. Measurements of the level of activation of caspase-3 by Caspase-Glo®3/7 Assay kit showed that HSPA12B overexpression markedly inhibited caspase-3 activation. Notably, we demonstrated that the effects of HSPA12B on spinal astrocyte survival depended on activation of the PI3K/Akt signal pathway. These findings indicate that HSPA12B protects against spinal cord ischemia-reperfusion injury and may represent a potential treatment target.

The statistical background to proposed ASME/MPC fracture toughness reference curves

International Nuclear Information System (INIS)

Oldfield, W.

1981-01-01

The ASME Pressure Vessel Codes define, in Sec. 11, lower bound fracture toughness curves. These curves are used to predict the lower bound fracture toughness on the basis of the RT test procedure. This test is used to remove heat to heat differences, by permitting the lower bound (reference) curve to be moved along the temperature scale according to the measured RT. Numerous objections have been raised to the procedure, and a Subcommittee (the ASME/MPC Working Group on Reference Toughness) is currently revising the codified procedures for fracture toughness prediction. The task has required a substantial amount of statistical work, since the new procedure are to have a statistical basis. Using initiation fracture toughness (J-Integral R curve procedures in the ductile domain) it was shown that when CVN energy data is properly transformed it is highly correlated with valid fracture toughness measurements. A single functional relationship can be used to predict the mean fracture toughness for a sample of steel from a set of CVN energy measurements, and the coefficients of the function tabulated. More importantly, the approximate lower statistical bounds to the initiation fracture toughness behaviour can be similarly predicted, and coefficients for selected bounds have also been tabulated. (orig.)

Combination Treatment of Spores of Cl. Botulinum with Heat plus Radiation

Energy Technology Data Exchange (ETDEWEB)

Grecz, N.; Upadhyay, J.; Tang, T. C.; Lin, C. A. [Illinois Institute of Technology, Chicago, IL (United States)

1967-11-15

Radiation resistance of spores of Cl. botulinum is strongly affected by the temperature during irradiation. Very low radiation resistance was consistently observed at 0 Degree-Sign C when samples were in the liquid state. Below 0 Degree-Sign C, the resistance of spores increased because the solidly frozen medium presumably decreased the diffusion of free radicals. As temperature increased above 0 Degree-Sign C processes of radiation protection occurred. When spores were subjected to low levels of radiation (0.6-0.8 Mrad) the heat resistance of the surviving spores was very remarkedly decreased. Experiments were designed to study what kind of radiation damage, i.e. direct hit or indirect action, is responsible for the loss of heat resistance of spores. Indirect effects were reduced by freezing the medium and lowering the temperature during irradiation down to -196 Degree-Sign C. Spores of Cl. botulinum 33A in phosphate buffer were irradiated to 0.6, 0.8 and 1.0 Mrad at irradiation temperatures ranging from +25 to -196 Degree-Sign C and subsequently heated at 99 Degree-Sign C. Survival curves revealed that all spores irradiated at +25 and 0 Degree-Sign C were highly sensitive to heat with D{sub 10} = 5.5 min (after 0.6 Mrad), D{sub 10} = 3.0 min (after 0.8 Mrad) and D{sub 10} = 2.3 min (after 1.0 Mrad). For nonTirradiated controls D10 was 23 min. Pre-irradiation at -25 through -196 Degree-Sign C resulted in a much smaller loss of heat resistance with D{sub 10} clustering around 17.4 min (after 0.6 Mrad), 13. 5 min (after 0.8 Mrad) and 11.5 min (after 1.0 Mrad). Loss of heat resistance after pre-irradiation at +25 and 0 Degree-Sign C was highly influenced by the liquid state of suspending medium whereas at -25 through -196 Degree-Sign C it depended primarily on radiation dose. The mechanism of heat sensitization of spores seems to be related primarily to migrating active free radicals at +25 and 0 Degree-Sign C and to random splitting of molecular bonds at -25 to -196

Light mirror reflection combined with heating/cooling curves as a method of studying phase transitions in transparent and opaque petroleum products: Apparatus and theory

International Nuclear Information System (INIS)

Shishkin, Yu.L.

2007-01-01

A portable low weight low cost apparatus 'Phasafot' and method for determining pour and cloud points of petroleum products, as well as precipitation and melting temperatures of paraffins in both transparent (diesel fuels), semi-transparent (lube oils) and opaque (crude oils) samples are described. The method consists in illuminating the surface of a sample with an oblique light beam and registering the intensity of specularly reflected light while heating/cooling the sample in the temperature range of its structural transitions. The mirror reflection of a light beam from an ideally smooth liquid surface falls in intensity when the surface becomes rough (dim) due to crystal formation. Simultaneous recording of the temperature ramp curve and the mirror reflection curve enables the determination of the beginning and end of crystallization of paraffins in both transparent and opaque petroleum products. Besides, their rheological properties can be accurately determined by rocking or tilting the instrument while monitoring the sample movement via its mirror reflection

Microgeographic differentiation in thermal performance curves between rural and urban populations of an aquatic insect.

Science.gov (United States)

Tüzün, Nedim; Op de Beeck, Lin; Brans, Kristien I; Janssens, Lizanne; Stoks, Robby

2017-12-01

The rapidly increasing rate of urbanization has a major impact on the ecology and evolution of species. While increased temperatures are a key aspect of urbanization ("urban heat islands"), we have very limited knowledge whether this generates differentiation in thermal responses between rural and urban populations. In a common garden experiment, we compared the thermal performance curves (TPCs) for growth rate and mortality in larvae of the damselfly Coenagrion puella from three urban and three rural populations. TPCs for growth rate shifted vertically, consistent with the faster-slower theoretical model whereby the cold-adapted rural larvae grew faster than the warm-adapted urban larvae across temperatures. In line with costs of rapid growth, rural larvae showed lower survival than urban larvae across temperatures. The relatively lower temperatures hence expected shorter growing seasons in rural populations compared to the populations in the urban heat islands likely impose stronger time constraints to reach a certain developmental stage before winter, thereby selecting for faster growth rates. In addition, higher predation rates at higher temperature may have contributed to the growth rate differences between urban and rural ponds. A faster-slower differentiation in TPCs may be a widespread pattern along the urbanization gradient. The observed microgeographic differentiation in TPCs supports the view that urbanization may drive life-history evolution. Moreover, because of the urban heat island effect, urban environments have the potential to aid in developing predictions on the impact of climate change on rural populations.

Inactivation kinetics of Escherichia coli O157:H7, Salmonella enterica Serovar Typhimurium, and Listeria monocytogenes in ready-to-eat sliced ham by near-infrared heating at different radiation intensities.

Science.gov (United States)

Ha, Jae-Won; Kang, Dong-Hyun

2014-07-01

The aim of this study was to investigate the inactivation kinetics of Salmonella enterica serovar Typhimurium, Escherichia coli O157:H7, and Listeria monocytogenes on ready-to-eat sliced ham by near-infrared (NIR) heating as a function of the processing parameter, radiation intensity. Precooked ham slices inoculated with the three pathogens were treated at different NIR intensities (ca. 100, 150, and 200 μW/cm(2)/nm). An increase in the applied radiation intensity resulted in a gradual increase of inactivation of all pathogens. The survival curves of the three pathogens exhibited both shoulder and tailing behavior at all light intensities. Among nonlinear models, the Weibull distribution and log-logistic model were used to describe the experimental data, and the statistical results (mean square error and R(2) values) indicated the suitability of the model for prediction. The log-logistic model more accurately described survival curves of the three pathogens than did the Weibull distribution at all radiation intensities. The output of this study and the proposed kinetics model would be beneficial to the deli meat industry for selecting the optimum processing conditions of NIR heating to meet the target pathogen inactivation on ready-to-eat sliced ham.

Prognostic classification index in Iranian colorectal cancer patients: Survival tree analysis

Directory of Open Access Journals (Sweden)

Amal Saki Malehi

2016-01-01

Full Text Available Aims: The aim of this study was to determine the prognostic index for separating homogenous subgroups in colorectal cancer (CRC patients based on clinicopathological characteristics using survival tree analysis. Methods: The current study was conducted at the Research Center of Gastroenterology and Liver Disease, Shahid Beheshti Medical University in Tehran, between January 2004 and January 2009. A total of 739 patients who already have been diagnosed with CRC based on pathologic report were enrolled. The data included demographic and clinical-pathological characteristic of patients. Tree-structured survival analysis based on a recursive partitioning algorithm was implemented to evaluate prognostic factors. The probability curves were calculated according to the Kaplan-Meier method, and the hazard ratio was estimated as an interest effect size. Result: There were 526 males (71.2% of these patients. The mean survival time (from diagnosis time was 42.46± (3.4. Survival tree identified three variables as main prognostic factors and based on their four prognostic subgroups was constructed. The log-rank test showed good separation of survival curves. Patients with Stage I-IIIA and treated with surgery as the first treatment showed low risk (median = 34 months whereas patients with stage IIIB, IV, and more than 68 years have the worse survival outcome (median = 9.5 months. Conclusion: Constructing the prognostic classification index via survival tree can aid the researchers to assess interaction between clinical variables and determining the cumulative effect of these variables on survival outcome.

Starvation-survival of subsurface bacteria

International Nuclear Information System (INIS)

Magill, N.G.

1988-01-01

The ability of four subsurface isolates to survive starvation was examined and the results were compared to survival curves obtained for Escherichia coli B and Serratia marcescens. To examine the starvation-survival phenomenon further, several experimental parameters including nutritional history, initial cell density, growth phase, temperature of growth and starvation, and aeration. Nutritional history, initial cell density, and growth phases of the cells had some effect on the ability of these bacteria to survive whereas temperature and limited aeration had no effect under the conditions tested. No conditions were found where E. coli B or Serratia marcescens died rapidly or where less than 10% of the original cell number of viable cells remained. Because the apparent survival of these bacteria may be due to cryptic growth, cross-feeding experiments with 14 C-labeled cells and unlabeled cells were carried out with E. coli B and Pseudomonas Lula V. Leaked extracellular 14 C-compounds were not used for growth or maintenance energy, and were not taken up by either bacterium. Cryptic growth did not occur; the cells were truly starving under the experimental conditions used

Effects of heat stress on baroreflex function in humans

Science.gov (United States)

Crandall, Craig G.; Cui, Jian; Wilson, Thad E.

2003-01-01

INTRODUCTION: Heat stress significantly reduces orthostatic tolerance in humans. The mechanism(s) causing this response remain unknown. The purpose of this review article is to present data pertaining to the hypothesis that reduced orthostatic tolerance in heat stressed individuals is a result of heat stress induced alterations in baroflex function. METHODS: In both normothermic and heat stressed conditions baroreflex responsiveness was assessed via pharmacological and non-pharmacological methods. In addition, the effects of heat stress on post-synaptic vasoconstrictor responsiveness were assessed. RESULTS: Generally, whole body heating did not alter baroreflex sensitivity defined as the gain of the linear portion of the baroreflex curve around the operating point. However, whole body heating shifted the baroreflex curve to the prevailing (i.e. elevated) heart rate and muscle sympathetic nerve activity. Finally, the heat stress impaired vasoconstrictor responses to exogenous administration of adrenergic agonists. CONCLUSION: Current data do not support the hypothesis that reduced orthostatic tolerance associated with heat stress in humans is due to impaired baroreflex responsiveness. This phenomenon may be partially due to the effects of heat stress on reducing vasoconstrictor responsiveness.

Prediction of ttt curves of cold working tool steels using support vector machine model

Science.gov (United States)

Pillai, Nandakumar; Karthikeyan, R., Dr.

2018-04-01

The cold working tool steels are of high carbon steels with metallic alloy additions which impart higher hardenability, abrasion resistance and less distortion in quenching. The microstructure changes occurring in tool steel during heat treatment is of very much importance as the final properties of the steel depends upon these changes occurred during the process. In order to obtain the desired performance the alloy constituents and its ratio plays a vital role as the steel transformation itself is complex in nature and depends very much upon the time and temperature. The proper treatment can deliver satisfactory results, at the same time process deviation can completely spoil the results. So knowing time temperature transformation (TTT) of phases is very critical which varies for each type depending upon its constituents and proportion range. To obtain adequate post heat treatment properties the percentage of retained austenite should be lower and metallic carbides obtained should be fine in nature. Support vector machine is a computational model which can learn from the observed data and use these to predict or solve using mathematical model. Back propagation feedback network will be created and trained for further solutions. The points on the TTT curve for the known transformations curves are used to plot the curves for different materials. These data will be trained to predict TTT curves for other steels having similar alloying constituents but with different proportion range. The proposed methodology can be used for prediction of TTT curves for cold working steels and can be used for prediction of phases for different heat treatment methods.

Survival of foot-and-mouth disease virus in cheese.

Science.gov (United States)

Blackwell, J H

1976-09-01

Persistence of foot-and-mouth disease virus during the manufacture of Cheddar, Mozzarella, Camembert cheese prepared from milk of cows experimentally infected with the virus was studied. Cheese samples were made on a laboratory scale with commercial lactic acid starter cultures and the microbial protease MARZYME as a coagulant. Milk was heated at different temperatures for different intervals before it was made into cheese. Food-and-mouth disease virus survived the acidic conditions of Cheddar and Camembert cheese processing but not that of Mozzarella. Foot-and-mouth disease virus survived processing but not curing for 30 days in Cheddar cheese preparaed from heated milk. However, the virus survived curing for 60 days but not for 120 days in cheese (pH 5) prepared from unheated milk. Foot-and-mouth disease virus survived in Camembert cheese (pH 5) for 21 days at 2 C but not for 35 days.

Experimental study on forced convection boiling heat transfer on molten alloy

International Nuclear Information System (INIS)

Nishimura, Satoshi; Ueda, Nobuyuki; Nishi, Yoshihisa; Furuya, Masahiro; Kinoshita, Izumi

1999-01-01

In order to clarify the characteristics of forced convection boiling heat transfer on molten metal, basic experiments have been carried out with subcooled water flowing on molten Wood's alloy pool surface. In these experiments, water flows horizontally in a rectangular duct. A cavity filled with Wood's alloy is present in a portion of the bottom of the duct. Wood's alloy is heated by a copper conductor at the bottom of the cavity. The experiments have been carried out with various velocities and subcoolings of water, and temperature of Wood's alloy. Boiling curves on the molten alloy surface were obtained and compared with that on a solid heat transfer surface. It is observed that the boiling curve on molten alloy is in a lower superheat region than the boiling curve on a solid surface. This indicates that the heat transfer performance of forced convection boiling on molten alloy is enhanced by increase of the heat transfer area, due to oscillation of the surface and fragmentation of molten alloy

Survival of mouse testicular stem cells after γ or neutron irradiation

International Nuclear Information System (INIS)

Lu, C.C.; Meistrich, M.L.; Thames, H.D. Jr.

1980-01-01

The survival of mouse testicular stem cells after γ or neutron irradiation was measured by counts of repopulated tubular cross sections and by the numbers of differentiated spermatogenic cells produced. The numbers of such cells were determined either by sperm head counts of the X-isozyme of lactate dehydrogenase enzyme levels. Qualitatively similar results were obtained with all three assays. The results have confirmed that, with C3H mice, stem-cell survival is higher when the γ-radiation dose is fractionated by a 24-h interval. Single-dose γ-radiaton survival curves for the stem cell had large shoulders and also showed the presence of a radioresistant subpopulation which predominated after doses greater than 600 rad. Part of the shoulder must have resulted from repair of sublethal damage since neutron irradiation produced survival curves with smaller shoulders. The relative biological effectiveness for stem-cell killing for these neutrons (mean energy, 22 MeV) varied from about 2.9 at 10 rad of γ radiation to 2.2 at 600 rad

LONG DURATION FLARE EMISSION: IMPULSIVE HEATING OR GRADUAL HEATING?

Energy Technology Data Exchange (ETDEWEB)

Qiu, Jiong; Longcope, Dana W. [Department of Physics, Montana State University, Bozeman MT 59717-3840 (United States)

2016-03-20

Flare emissions in X-ray and EUV wavelengths have previously been modeled as the plasma response to impulsive heating from magnetic reconnection. Some flares exhibit gradually evolving X-ray and EUV light curves, which are believed to result from superposition of an extended sequence of impulsive heating events occurring in different adjacent loops or even unresolved threads within each loop. In this paper, we apply this approach to a long duration two-ribbon flare SOL2011-09-13T22 observed by the Atmosphere Imaging Assembly (AIA). We find that to reconcile with observed signatures of flare emission in multiple EUV wavelengths, each thread should be heated in two phases, an intense impulsive heating followed by a gradual, low-rate heating tail that is attenuated over 20–30 minutes. Each AIA resolved single loop may be composed of several such threads. The two-phase heating scenario is supported by modeling with both a zero-dimensional and a 1D hydrodynamic code. We discuss viable physical mechanisms for the two-phase heating in a post-reconnection thread.

Benchmark numerical solutions for radiative heat transfer in two-dimensional medium with graded index distribution

Energy Technology Data Exchange (ETDEWEB)

Liu, L.H. [School of Energy Science and Engineering, Harbin Institute of Technology, 92 West Dazhi Street, Harbin 150001 (China)]. E-mail: lhliu@hit.edu.cn

2006-11-15

In graded index media, the ray goes along a curved path determined by Fermat principle. Generally, the curved ray trajectory in graded index media is a complex implicit function, and the curved ray tracing is very difficult and complex. Only for some special refractive index distributions, the curved ray trajectory can be expressed as a simple explicit function. Two important examples are the layered and the radial graded index distributions. In this paper, the radiative heat transfer problems in two-dimensional square semitransparent with layered and radial graded index distributions are analyzed. After deduction of the ray trajectory, the radiative heat transfer problems are solved by using the Monte Carlo curved ray-tracing method. Some numerical solutions of dimensionless net radiative heat flux and medium temperature are tabulated as the benchmark solutions for the future development of approximation techniques for multi-dimensional radiative heat transfer in graded index media.

[Comparative evaluation of survival prognosis using MELD or Child-Pugh scores in patients with liver cirrhosis in Chile].

Science.gov (United States)

Sanhueza, Edgar; Contreras, Jorge; Zapata, Rodrigo; Sanhueza, Matías; Elgueta, Fabián; López, Constanza; Jerez, Sigrid; Jerez, Verónica; Delgado, Iris

2017-01-01

Currently, most liver units use the Child-Pugh (CP) or the Model for End-Stage Liver Disease (MELD) scores to establish survival prognosis among patients with liver cirrhosis. Which classification is superior, is not well defined. To compare CP and MELD classification scores to predict survival among adult patients with liver cirrhosis in Chile. Follow-up of 137 consecutive adult patients with liver cirrhosis aged 59 ± 12 years (55% women). The diagnosis was reached by clinical, laboratory and image studies at three different centers of Santiago. Patients were staged with CP and MELD classification scores at baseline and followed over a period of 12 months. The predictive capacity of the scores for survival was analyzed using a multivariate statistical analysis (Kaplan-Meier curves). The most common etiology was alcohol (37.9%). The actuarial survival rate was 79.6% at 12 months of follow-up. When comparing groups with areas under curve of receiver operating characteristic curves (AUROC), there was no statistically significant difference in survival between less severe and advanced disease, assessed with both survival scales. The AUROC for MELD and CP were 0.80 and 0.81, respectively. This clinical study did not find a statistically significant difference between the two classifications for the prediction of 12 months survival in patients with cirrhosis.

Dissipative dark matter and the rotation curves of dwarf galaxies

International Nuclear Information System (INIS)

Foot, R.

2016-01-01

There is ample evidence from rotation curves that dark matter halos around disk galaxies have nontrivial dynamics. Of particular significance are: a) the cored dark matter profile of disk galaxies, b) correlations of the shape of rotation curves with baryonic properties, and c) Tully-Fisher relations. Dark matter halos around disk galaxies may have nontrivial dynamics if dark matter is strongly self interacting and dissipative. Multicomponent hidden sector dark matter featuring a massless 'dark photon' (from an unbroken dark U(1) gauge interaction) which kinetically mixes with the ordinary photon provides a concrete example of such dark matter. The kinetic mixing interaction facilitates halo heating by enabling ordinary supernovae to be a source of these 'dark photons'. Dark matter halos can expand and contract in response to the heating and cooling processes, but for a sufficiently isolated halo could have evolved to a steady state or 'equilibrium' configuration where heating and cooling rates locally balance. This dynamics allows the dark matter density profile to be related to the distribution of ordinary supernovae in the disk of a given galaxy. In a previous paper a simple and predictive formula was derived encoding this relation. Here we improve on previous work by modelling the supernovae distribution via the measured UV and H α fluxes, and compare the resulting dark matter halo profiles with the rotation curve data for each dwarf galaxy in the LITTLE THINGS sample. The dissipative dark matter concept is further developed and some conclusions drawn.

Dissipative dark matter and the rotation curves of dwarf galaxies

Energy Technology Data Exchange (ETDEWEB)

Foot, R., E-mail: rfoot@unimelb.edu.au [ARC Centre of Excellence for Particle Physics at the Terascale, School of Physics, University of Melbourne, Victoria 3010 (Australia)

2016-07-01

There is ample evidence from rotation curves that dark matter halos around disk galaxies have nontrivial dynamics. Of particular significance are: a) the cored dark matter profile of disk galaxies, b) correlations of the shape of rotation curves with baryonic properties, and c) Tully-Fisher relations. Dark matter halos around disk galaxies may have nontrivial dynamics if dark matter is strongly self interacting and dissipative. Multicomponent hidden sector dark matter featuring a massless 'dark photon' (from an unbroken dark U(1) gauge interaction) which kinetically mixes with the ordinary photon provides a concrete example of such dark matter. The kinetic mixing interaction facilitates halo heating by enabling ordinary supernovae to be a source of these 'dark photons'. Dark matter halos can expand and contract in response to the heating and cooling processes, but for a sufficiently isolated halo could have evolved to a steady state or 'equilibrium' configuration where heating and cooling rates locally balance. This dynamics allows the dark matter density profile to be related to the distribution of ordinary supernovae in the disk of a given galaxy. In a previous paper a simple and predictive formula was derived encoding this relation. Here we improve on previous work by modelling the supernovae distribution via the measured UV and H α fluxes, and compare the resulting dark matter halo profiles with the rotation curve data for each dwarf galaxy in the LITTLE THINGS sample. The dissipative dark matter concept is further developed and some conclusions drawn.

Characterization and radiation response of a heat-resistant variant of V79 cells

International Nuclear Information System (INIS)

Campbell, S.D.; Kruuv, J.; Lepock, J.R.

1983-01-01

A thermoresistant variant of the established cell line V79-S171-W1 was isolated after treatment with nitrosoguanidine and repeated heat treatments at 42.6 to 43 degrees C, and showed an enhanced ability to survive at 42.6, 43.5, and 44.5 degrees C. The rates of inactivation of the normal and heat-resistant lines differed by approximately a factor of 2 over this temperature range. This level of thermoresistance was stable for the first 80 doublings, but was lost by 120 doublings. This may have been due to a reversion to the normal V79 line since there was no continuous selection pressure and the thermoresistant variant, which was designated at HR7, had a longer average doubling time. Transient thermotolerance was induced in both the V79 and HR7 cells by a 10-min exposure to 44.5 degrees C. After 3 hr incubation at 37 degrees C, both cell lines had an identical sensitivity to further exposure to 44.5 degrees C. Thus the long-term thermoresistance of the HR7 cells may be due to a permanent induction of a low level of thermotolerance. The (ionizing) radiation survival curves and the ability to repair sublethal radiation damage were identical for the thermoresistant variant and the parent cell line

Dose-rate dependent stochastic effects in radiation cell-survival models

International Nuclear Information System (INIS)

Sachs, R.K.; Hlatky, L.R.

1990-01-01

When cells are subjected to ionizing radiation the specific energy rate (microscopic analog of dose-rate) varies from cell to cell. Within one cell, this rate fluctuates during the course of time; a crossing of a sensitive cellular site by a high energy charged particle produces many ionizations almost simultaneously, but during the interval between events no ionizations occur. In any cell-survival model one can incorporate the effect of such fluctuations without changing the basic biological assumptions. Using stochastic differential equations and Monte Carlo methods to take into account stochastic effects we calculated the dose-survival rfelationships in a number of current cell survival models. Some of the models assume quadratic misrepair; others assume saturable repair enzyme systems. It was found that a significant effect of random fluctuations is to decrease the theoretically predicted amount of dose-rate sparing. In the limit of low dose-rates neglecting the stochastic nature of specific energy rates often leads to qualitatively misleading results by overestimating the surviving fraction drastically. In the opposite limit of acute irradiation, analyzing the fluctuations in rates merely amounts to analyzing fluctuations in total specific energy via the usual microdosimetric specific energy distribution function, and neglecting fluctuations usually underestimates the surviving fraction. The Monte Carlo methods interpolate systematically between the low dose-rate and high dose-rate limits. As in other approaches, the slope of the survival curve at low dose-rates is virtually independent of dose and equals the initial slope of the survival curve for acute radiation. (orig.)

Analysis of pre-heated fuel combustion and heat-emission dynamics in a diesel engine

Science.gov (United States)

Plotnikov, S. A.; Kartashevich, A. N.; Buzikov, S. V.

2018-01-01

The article explores the feasibility of diesel fuel pre-heating. The research goal was to obtain and analyze the performance diagrams of a diesel engine fed with pre-heated fuel. The engine was tested in two modes: at rated RPMs and at maximum torque. To process the diagrams the authors used technique developed by the Central Diesel Research Institute (CDRI). The diesel engine’s heat emission curves were obtained. The authors concluded that fuel pre-heating shortened the initial phase of the combustion process and moderated the loads, thus making it possible to boost a diesel engine’s mean effective pressure.

Lagrangian Curves on Spectral Curves of Monopoles

International Nuclear Information System (INIS)

Guilfoyle, Brendan; Khalid, Madeeha; Ramon Mari, Jose J.

2010-01-01

We study Lagrangian points on smooth holomorphic curves in TP 1 equipped with a natural neutral Kaehler structure, and prove that they must form real curves. By virtue of the identification of TP 1 with the space LE 3 of oriented affine lines in Euclidean 3-space, these Lagrangian curves give rise to ruled surfaces in E 3 , which we prove have zero Gauss curvature. Each ruled surface is shown to be the tangent lines to a curve in E 3 , called the edge of regression of the ruled surface. We give an alternative characterization of these curves as the points in E 3 where the number of oriented lines in the complex curve Σ that pass through the point is less than the degree of Σ. We then apply these results to the spectral curves of certain monopoles and construct the ruled surfaces and edges of regression generated by the Lagrangian curves.

Effect of subcooling and wall thickness on pool boiling from downward-facing curved surfaces in water

Energy Technology Data Exchange (ETDEWEB)

El-Genk, M.S.; Glebov, A.G. [Univ. of New Mexico, Albuquerque, NM (United States)

1995-09-01

Quenching experiments were performed to investigate the effects of water subcooling and wall thickness on pool boiling from a downward-facing curved surface. Experiments used three copper sections of the same diameter (50.8 mm) and surface radius (148 mm), but different thickness (12.8, 20 and 30 mm). Local and average pool boiling curves were obtained at saturation and 5 K, 10 K, and 14 K subcooling. Water subcooling increased the maximum heat flux, but decreased the corresponding wall superheat. The minimum film boiling heat flux and the corresponding wall superheat, however, increased with increased subcooling. The maximum and minimum film boiling heat fluxes were independent of wall thickness above 20 mm and Biot Number > 0.8, indicating that boiling curves for the 20 and 30 thick sections were representative of quasi steady-state, but not those for the 12.8 mm thick section. When compared with that for a flat surface section of the same thickness, the data for the 12.8 mm thick section showed significant increases in both the maximum heat flux (from 0.21 to 0.41 MW/m{sup 2}) and the minimum film boiling heat flux (from 2 to 13 kW/m{sup 2}) and about 11.5 K and 60 K increase in the corresponding wall superheats, respectively.

Effect of heating rate and grain size on the melting behavior of the alloy Nb-47 mass % Ti in pulse-heating experiments

International Nuclear Information System (INIS)

Basak, D.; Boettinger, W.J.; Josell, D.; Coriell, S.R.; McClure, J.L.; Cezairliyan, A.

1999-01-01

The effect of heating rate and grain size on the melting behavior of Nb-47 mass% Ti is measured and modeled. The experimental method uses rapid resistive self-heating of wire specimens at rates between ∼10 2 and ∼10 4 K/s and simultaneous measurement of radiance temperature and normal spectral emissivity as functions of time until specimen collapse, typically between 0.4 and 0.9 fraction melted. During heating, a sharp drop in emissivity is observed at a temperature that is independent of heating rate and grain size. This drop is due to surface and grain boundary melting at the alloy solidus temperature even though there is very little deflection (limited melting) of the temperature-time curve from the imposed heating rate. Above the solidus temperature, the emissivity remains nearly constant with increasing temperature and the temperature vs time curve gradually reaches a sloped plateau over which the major fraction of the specimen melts. As the heating rate and/or grain size is increased, the onset temperature of the sloped plateau approaches the alloy liquidus temperature and the slope of the plateau approaches zero. This interpretation of the shapes of the temperature-time-curves is supported by a model that includes diffusion in the solid coupled with a heat balance during the melting process. There is no evidence of loss of local equilibrium at the melt front during melting in these experiments

Effects of time-temperature profiles on glow curves of germanium-doped optical fibre

Science.gov (United States)

Lam, S. E.; Alawiah, A.; Bradley, D. A.; Mohd Noor, N.

2017-08-01

The Germanium (Ge) doped silica optical fibres have demonstrated the great potential to be developed as a thermoluminescent (TL) dosimeter that can be used in various applications in radiotherapy, diagnostic radiology, UV dosimetry system and food irradiation industry. Different time-temperature profile (TTP) parameters of the TL reader have been employed by many researchers in various of TL studies. Nevertheless, none of those studies adequately addressed the effects of the reader's preheat temperature and heating rate on the kinetic parameters of the TL glow curve specifically, the Ge-doped silica optical fibres. This research addresses the issue of TTP parameters with special attention to the determination of the kinetic parameters of the glow curve. The glow curve responses were explored and the kinetic parameters were analyzed by the WinGCF software, to show the effect of the preheat temperature and heating rate of the reader on Ge-doped fibre irradiated with 18 Gy of 6 MV photons radiation. The effect of TTP parameters was discussed and compared against the commercial fibre and tailored made fibre of 6 mol% Ge-doped of flat and cylindrical shape. The deconvolution of glow peaks and the kinetic parameters were obtained by the WinGCF software. This enables to fit accurately (1.5%curves. A positive, moderate linear relationship exists between the TL response and the heating rate when the specific preheat temperature was used to read commercial fibre (50 °C) and cylindrical fibre (80 °C and 160 °C). It is found that the glow peaks of cylindrical fibre exhibit the highest peak integral as compared to flat and commercial fibres. This study revealed the possible relationship between the reader's TTP parameters and the kinetic parameters of TL glow curves for the commercial and tailored made Ge-doped silica optical fibres.

DETERMINATION OF CONVECTIVE HEAT TRANSFER COEFFICIENT AT THE OUTER SURFACE OF A CRYOVIAL BEING PLUNGED INTO LIQUID NITROGEN.

Science.gov (United States)

Wang, T; Zhao, G; Tang, H Y; Jiang, Z D

2015-01-01

Cell survival upon cryopreservation is affected by the cooling rate. However, it is difficult to model the heat transfer process or to predict the cooling curve of a cryoprotective agent (CPA) solution due to the uncertainty of its convective heat transfer coefficient (h). To measure the h and to better understand the heat transfer process of cryovials filled with CPA solution being plunged in liquid nitrogen. The temperatures at three locations of the CPA solution in a cryovial were measured. Different h values were selected after the cooling process was modeled as natural convection heat transfer, the film boiling and the nucleate boiling, respectively. And the temperatures of the selected points are simulated based on the selected h values. h was determined when the simulated temperature best fitted the experimental temperature. When the experimental results were best fitted, according to natural convection heat transfer model, h(1) = 120 W/(m(2)·K) while due to film boiling and nucleate boiling regimes h(f) = 5 W/(m(2)·K) followed by h(n) = 245 W/(m(2)·K). These values were verified by the differential cooling rates at the three locations of a cryovial. The heat transfer process during cooling in liquid nitrogen is better modeled as film boiling followed by nucleate boiling.

Heating and cooling with ground-loop heat pumps; Heizen und Kuehlen mit erdgekoppelten Waermepumpen

Energy Technology Data Exchange (ETDEWEB)

Afjei, Th.; Dott, R. [Institut Energie am Bau, Fachhochschule Nordwestschweiz (FHNW), Muttenz (Switzerland); Huber, A. [Huber Energietechnik AG, Zuerich (Switzerland)

2007-08-15

This final report for the Swiss Federal Office of Energy (SFOE) presents the results of the SFOE-project 'Heating and cooling with ground coupled heat pumps' in which the benefits and costs of a heat pump heating and cooling system with a borehole heat exchanger were examined. In particular the dimensioning of the hydraulic system, control concept and user behaviour are dealt with. The results of the simulations of thermal building behaviour with MATLAB/SIMULINK, CARNOT, and EWS are discussed. The results of parameter studies carried out, including varying shading, cooling characteristic curves, temperature differences in the heat exchanger and the dead time between heating and cooling mode are discussed. These showed that a simple system with heat pump and borehole heat exchanger for heating or preparation of domestic hot water as well as for passive cooling proved to be the best choice.

Numerical analysis of transient heat conduction in downward-facing curved sections during quenching

International Nuclear Information System (INIS)

Gao, C.; El-Genk, M.S.

1996-01-01

Pool boiling from downward-facing surfaces is of interest in many applications such as cooling of electric cables, handling of containers of hazardous liquids and external cooling of nuclear reactor vessels. Here, a two-dimensional numerical analysis was performed to determine pool boiling curves from downward-facing curved stainless-steel and copper surfaces during quenching in saturated water. To ensure stability and accuracy of the numerical solution, the alternating direction implicit (ADI) method based on finite control volume representations was employed. A time dependent boundary condition was provided by the measured temperature at nine interior locations near the boiling surface. Best results were obtained using a grid of 20x20 CVs and a non-iterative approach. Calculated temperatures near the top surface of the metal sections agreed with measured values to within 0.5 K and 2.5 K for the copper and stainless-steel sections, respectively. The running time on a Pentium 90 MHz PC for the entire boiling curve was 7% of the real transient time and 4% of that of a simplified Gaussian elimination (SGE) method for the Crank-Nicolson scheme

Numerical modeling of the effect of surface topology on the saturated pool nucleate boiling curve

International Nuclear Information System (INIS)

Unal, C.; Pasamehmetoglu, K.O.

1993-01-01

A numerical study of saturated pool nucleate boiling with an emphasis on the effect of surface topography is presented. The numerical model consisted of solving the three-dimensional transient heat conduction equation within the heater subjected to nucleate boiling over its upper surface. The surface topography model considered the distribution of the cavity and cavity angles based on exponential and normal probability functions. Parametric results showed that the saturated nucleate boiling curve shifted left and became steeper with an increase in the mean cavity radius. The boiling curve was found to be sensitive to the selection of how many cavities were selected for each octagonal cell. A small variation in the statistical parameters, especially cavity radii for smooth surfaces, resulted in noticeable differences in wall superheat for a given heat flux. This result indicated that while the heat transfer coefficient increased with cavity radii, the cavity radii or height alone was not sufficient to characterize the boiling curve. It also suggested that statistical experimental data should consider large samples to characterize the surface topology. The boiling curve shifted to the right when the cavity angle was obtained using a normal distribution. This effect became less important when the number of cavities for each cell was increasing because the probability of the potential cavity with a larger radius in each cell was increased. When the contact angle of the fluid decreased for a given mean cavity radii, the boiling curve shifted to the right. This shift was more pronounced at smaller mean cavity radii and decreased with increasing mean cavity radii

Influence of the interior design of a room on the room temperature curve and the heating energy. Einfluss der Innenbauweise eines Raumes auf den Raumtemperaturverlauf und die Heizenergie

Energy Technology Data Exchange (ETDEWEB)

Ruefenacht, A.

1981-01-01

This thesis contains a numerical method for the calculation of layer and surface temperature of any coated building component with any temperature curves for both sides. It is shown how interior heat sources and insolation of the surface can be included into the calculation. The effects of variations of the influence of the outer temperature on the energy household of buildings are of special interest; the main interest however is concentrated on the inner components.

REFLECTED LIGHT CURVES, SPHERICAL AND BOND ALBEDOS OF JUPITER- AND SATURN-LIKE EXOPLANETS

Energy Technology Data Exchange (ETDEWEB)

Dyudina, Ulyana; Kopparla, Pushkar; Ingersoll, Andrew P.; Yung, Yuk L. [Division of Geological and Planetary Sciences, 150-21 California Institute of Technology, Pasadena, CA 91125 (United States); Zhang, Xi [University of California Santa Cruz 1156 High Street, Santa Cruz, CA 95064 (United States); Li, Liming [Department of Physics, University of Houston, Houston, TX 77204 (United States); Dones, Luke [Southwest Research Institute, 1050 Walnut Street, Suite 300, Boulder CO 80302 (United States); Verbiscer, Anne, E-mail: ulyana@gps.caltech.edu [Department of Astronomy, University of Virginia, Charlottesville, VA 22904-4325 (United States)

2016-05-10

Reflected light curves observed for exoplanets indicate that a few of them host bright clouds. We estimate how the light curve and total stellar heating of a planet depends on forward and backward scattering in the clouds based on Pioneer and Cassini spacecraft images of Jupiter and Saturn. We fit analytical functions to the local reflected brightnesses of Jupiter and Saturn depending on the planet’s phase. These observations cover broadbands at 0.59–0.72 and 0.39–0.5 μ m, and narrowbands at 0.938 (atmospheric window), 0.889 (CH4 absorption band), and 0.24–0.28 μ m. We simulate the images of the planets with a ray-tracing model, and disk-integrate them to produce the full-orbit light curves. For Jupiter, we also fit the modeled light curves to the observed full-disk brightness. We derive spherical albedos for Jupiter and Saturn, and for planets with Lambertian and Rayleigh-scattering atmospheres. Jupiter-like atmospheres can produce light curves that are a factor of two fainter at half-phase than the Lambertian planet, given the same geometric albedo at transit. The spherical albedo is typically lower than for a Lambertian planet by up to a factor of ∼1.5. The Lambertian assumption will underestimate the absorption of the stellar light and the equilibrium temperature of the planetary atmosphere. We also compare our light curves with the light curves of solid bodies: the moons Enceladus and Callisto. Their strong backscattering peak within a few degrees of opposition (secondary eclipse) can lead to an even stronger underestimate of the stellar heating.

Mutant p53 - heat shock response oncogenic cooperation: a new mechanism of cancer cell survival

Directory of Open Access Journals (Sweden)

Evguenia eAlexandrova

2015-04-01

Full Text Available The main tumor suppressor function of p53 as a ‘guardian of the genome’ is to respond to cellular stress by transcriptional activation of apoptosis, growth arrest or senescence in damaged cells. Not surprisingly, mutations in the p53 gene are the most frequent genetic alteration in human cancers. Importantly, mutant p53 (mutp53 proteins not only lose their wild-type tumor suppressor activity, but also can actively promote tumor development. Two main mechanisms accounting for mutp53 proto-oncogenic activity are inhibition of the wild-type p53 in a dominant-negative fashion and gain of additional oncogenic activities known as gain-of-function (GOF. Here we discuss a novel mechanism of mutp53 GOF, which relies on its oncogenic cooperation with the heat shock machinery. This coordinated adaptive mechanism renders cancer cells more resistant to proteotoxic stress and provides both, a strong survival advantage to cancer cells and a promising means for therapeutic intervention.

Eddy current testing device for metallic tubes at least locally curved

International Nuclear Information System (INIS)

Pigeon, Marcel; Vienot, Claude.

1975-01-01

Steam generators, condensers and heat exchangers generally consist of metallic tube bundles, the tubes having a complex geometry. The invention concerns an Eddy current testing device for metallic tubes at least locally curved, operating by translation of a probe inside the tubes [fr

In vivo survival of [14C]sucrose-loaded porcine carrier erythrocytes

International Nuclear Information System (INIS)

DeLoach, J.R.

1983-01-01

Porcine carrier erythrocyte survival was measured in adult pigs. [14C]Sucrose-loaded erythrocytes had a biphasic survival curve, with as much as 50% of the cells removed from circulation in the first 24 hours. The remaining cells had a 35-day half-life. Encapsulation values were measured for porcine erythrocytes and entrapment of [14C]sucrose was greater than 45%. Addition of inosine and glucose to the dialyzed cells and to the final wash buffer before reinjection of autologous cells did not improve their survival

Heat transfer coefficient in pool boiling for an electrically heated tube at various inclinations

International Nuclear Information System (INIS)

Fahmy, A.S.A.; Mariy, A.H.; Mahmoud, S.I.; Ibrahim, N.A.

1987-01-01

An experimental investigation is carried out study the behaviour of heat transfer in pool boiling from a vertical and inclined heated tube at atmospheric pressure. An imperial correlation joining the different parameters affecting the heat transfer coefficient in pool boiling for an electrically heated tube at various inclinations is developed. Two test sections (zircaloy-4 and stainless steel) of 16 n n outer diameter and 120 nm length are investigated. Four levels of heat flux are used for heating the two lest sections (e.g. 381, 518, 721 and 929 k.watt/n 2). The maximum surface temperature achieved is 146.5 degree c for both materials, and the maximum bulk temperature is 95 degree C. It is found that the average heat transfer coefficient is inversely proportional with heated length l, where it reaches a constant value in the horizontal position. The heat transfer coefficient curves at various inclinations with respect to the heated tube length pass around one point which is defined as limit length

Two-phase Heating in Flaring Loops

Science.gov (United States)

Zhu, Chunming; Qiu, Jiong; Longcope, Dana W.

2018-03-01

We analyze and model a C5.7 two-ribbon solar flare observed by the Solar Dynamics Observatory, Hinode, and GOES on 2011 December 26. The flare is made of many loops formed and heated successively over one and half hours, and their footpoints are brightened in the UV 1600 Å before enhanced soft X-ray and EUV missions are observed in flare loops. Assuming that anchored at each brightened UV pixel is a half flaring loop, we identify more than 6700 half flaring loops, and infer the heating rate of each loop from the UV light curve at the footpoint. In each half loop, the heating rate consists of two phases: intense impulsive heating followed by a low-rate heating that is persistent for more than 20 minutes. Using these heating rates, we simulate the evolution of their coronal temperatures and densities with the model of the “enthalpy-based thermal evolution of loops.” In the model, suppression of thermal conduction is also considered. This model successfully reproduces total soft X-ray and EUV light curves observed in 15 passbands by four instruments GOES, AIA, XRT, and EVE. In this flare, a total energy of 4.9 × 1030 erg is required to heat the corona, around 40% of this energy is in the slow-heating phase. About two-fifths of the total energy used to heat the corona is radiated by the coronal plasmas, and the other three fifth transported to the lower atmosphere by thermal conduction.

Machine learning models in breast cancer survival prediction.

Science.gov (United States)

Montazeri, Mitra; Montazeri, Mohadeseh; Montazeri, Mahdieh; Beigzadeh, Amin

2016-01-01

Breast cancer is one of the most common cancers with a high mortality rate among women. With the early diagnosis of breast cancer survival will increase from 56% to more than 86%. Therefore, an accurate and reliable system is necessary for the early diagnosis of this cancer. The proposed model is the combination of rules and different machine learning techniques. Machine learning models can help physicians to reduce the number of false decisions. They try to exploit patterns and relationships among a large number of cases and predict the outcome of a disease using historical cases stored in datasets. The objective of this study is to propose a rule-based classification method with machine learning techniques for the prediction of different types of Breast cancer survival. We use a dataset with eight attributes that include the records of 900 patients in which 876 patients (97.3%) and 24 (2.7%) patients were females and males respectively. Naive Bayes (NB), Trees Random Forest (TRF), 1-Nearest Neighbor (1NN), AdaBoost (AD), Support Vector Machine (SVM), RBF Network (RBFN), and Multilayer Perceptron (MLP) machine learning techniques with 10-cross fold technique were used with the proposed model for the prediction of breast cancer survival. The performance of machine learning techniques were evaluated with accuracy, precision, sensitivity, specificity, and area under ROC curve. Out of 900 patients, 803 patients and 97 patients were alive and dead, respectively. In this study, Trees Random Forest (TRF) technique showed better results in comparison to other techniques (NB, 1NN, AD, SVM and RBFN, MLP). The accuracy, sensitivity and the area under ROC curve of TRF are 96%, 96%, 93%, respectively. However, 1NN machine learning technique provided poor performance (accuracy 91%, sensitivity 91% and area under ROC curve 78%). This study demonstrates that Trees Random Forest model (TRF) which is a rule-based classification model was the best model with the highest level of

EFFECT OF HEAT TREATMENT ON THE SURVIVAL OF ...

African Journals Online (AJOL)

BARTH EKWUEME

seconds at temperatures ranging from 69OC to 73OC. E. coli O157:H7 ... inoculum was added to 90ml of sterile raw milk (heated in water bath ..... the high temperature short time (HTST) pasteurization technique .... I. The use of selective media.

Acid, bile, and heat tolerance of free and microencapsulated probiotic bacteria.

Science.gov (United States)

Ding, W K; Shah, N P

2007-11-01

Eight strains of probiotic bacteria, including Lactobacillus rhamnosus, Bifidobacterium longum, L. salivarius, L. plantarum, L. acidophilus, L. paracasei, B. lactis type Bl-O4, and B. lactis type Bi-07, were studied for their acid, bile, and heat tolerance. Microencapsulation in alginate matrix was used to enhance survival of the bacteria in acid and bile as well as a brief exposure to heat. Free probiotic organisms were used as a control. The acid tolerance of probiotic organisms was tested using HCl in MRS broth over a 2-h incubation period. Bile tolerance was tested using 2 types of bile salts, oxgall and taurocholic acid, over an 8-h incubation period. Heat tolerance was tested by exposing the probiotic organisms to 65 degrees C for up to 1 h. Results indicated microencapsulated probiotic bacteria survived better (P strains. At 30 min of heat treatment, microencapsulated probiotic bacteria survived with an average loss of only 4.17-log CFU/mL, compared to 6.74-log CFU/mL loss with free probiotic bacteria. However, after 1 h of heating both free and microencapsulated probiotic strains showed similar losses in viability. Overall microencapsulation improved the survival of probiotic bacteria when exposed to acidic conditions, bile salts, and mild heat treatment.

Two-dimensional modeling of water and heat fluxes in green roof substrates

Science.gov (United States)

Suarez, F. I.; Sandoval, V. P.

2016-12-01

Due to public concern towards sustainable development, greenhouse gas emissions and energy efficiency, green roofs have become popular in the last years. Green roofs integrate vegetation into infrastructures to reach additional benefits that minimize negative impacts of the urbanization. A properly designed green roof can reduce environmental pollution, noise levels, energetic requirements or surface runoff. The correct performance of green roofs depends on site-specific conditions and on each component of the roof. The substrate and the vegetation layers strongly influence water and heat fluxes on a green roof. The substrate is an artificial media that has an improved performance compared to natural soils as it provides critical resources for vegetation survival: water, nutrients, and a growing media. Hence, it is important to study the effects of substrate properties on green roof performance. The objective of this work is to investigate how the thermal and hydraulic properties affect the behavior of a green roof through numerical modeling. The substrates that were investigated are composed by: crushed bricks and organic soil (S1); peat with perlite (S2); crushed bricks (S3); mineral soil with tree leaves (S4); and a mixture of topsoil and mineral soil (S5). The numerical model utilizes summer-arid meteorological information to evaluate the performance of each substrate. Results show that the area below the water retention curve helps to define the substrate that retains more water. In addition, the non-linearity of the water retention curve can increment the water needed to irrigate the roof. The heat propagation through the roof depends strongly on the hydraulic behavior, meaning that a combination of a substrate with low thermal conductivity and more porosity can reduce the heat fluxes across the roof. Therefore, it can minimize the energy consumed of an air-conditioner system.

Comparative Survival Rates of Human-Derived Probiotic Lactobacillus paracasei and L. salivarius Strains during Heat Treatment and Spray Drying

Science.gov (United States)

Gardiner, G. E.; O'Sullivan, E.; Kelly, J.; Auty, M. A. E.; Fitzgerald, G. F.; Collins, J. K.; Ross, R. P.; Stanton, C.

2000-01-01

Spray drying of skim milk was evaluated as a means of preserving Lactobacillus paracasei NFBC 338 and Lactobacillus salivarius UCC 118, which are human-derived strains with probiotic potential. Our initial experiments revealed that NFBC 338 is considerably more heat resistant in 20% (wt/vol) skim milk than UCC 118 is; the comparable decimal reduction times were 11.1 and 1.1 min, respectively, at 59°C. An air outlet temperature of 80 to 85°C was optimal for spray drying; these conditions resulted in powders with moisture contents of 4.1 to 4.2% and viable counts of 3.2 × 109 CFU/g for NFBC 338 and 5.2 × 107 CFU/g for UCC 118. Thus, L. paracasei NFBC 338 survived better than L. salivarius UCC 118 during spray drying; similar results were obtained when we used confocal scanning laser microscopy and LIVE/DEAD BacLight viability staining. In addition, confocal scanning laser microscopy revealed that the probiotic lactobacilli were located primarily in the powder particles. Although both spray-dried cultures appeared to be stressed, as shown by increased sensitivity to NaCl, bacteriocin production by UCC 118 was not affected by the process, nor was the activity of the bacteriocin peptide. The level of survival of NFBC 338 remained constant at ∼1 × 109 CFU/g during 2 months of powder storage at 4°C, while a decline in the level of survival of approximately 1 log (from 7.2 × 107 to 9.5 × 106 CFU/g) was observed for UCC 118 stored under the same conditions. However, survival of both Lactobacillus strains during powder storage was inversely related to the storage temperature. Our data demonstrate that spray drying may be a cost-effective way to produce large quantities of some probiotic cultures. PMID:10831444

r-PROCESS LANTHANIDE PRODUCTION AND HEATING RATES IN KILONOVAE

Energy Technology Data Exchange (ETDEWEB)

Lippuner, Jonas; Roberts, Luke F., E-mail: jlippuner@tapir.caltech.edu [TAPIR, Walter Burke Institute for Theoretical Physics, California Institute of Technology, MC 350-17, 1200 E California Boulevard, Pasadena CA 91125 (United States)

2015-12-20

r-process nucleosynthesis in material ejected during neutron star mergers may lead to radioactively powered transients called kilonovae. The timescale and peak luminosity of these transients depend on the composition of the ejecta, which determines the local heating rate from nuclear decays and the opacity. Kasen et al. and Tanaka and Hotokezaka pointed out that lanthanides can drastically increase the opacity in these outflows. We use the new general-purpose nuclear reaction network SkyNet to carry out a parameter study of r-process nucleosynthesis for a range of initial electron fractions Y{sub e}, initial specific entropies s, and expansion timescales τ. We find that the ejecta is lanthanide-free for Y{sub e} ≳ 0.22−0.30, depending on s and τ. The heating rate is insensitive to s and τ, but certain, larger values of Y{sub e} lead to reduced heating rates, due to individual nuclides dominating the heating. We calculate approximate light curves with a simplified gray radiative transport scheme. The light curves peak at about a day (week) in the lanthanide-free (-rich) cases. The heating rate does not change much as the ejecta becomes lanthanide-free with increasing Y{sub e}, but the light-curve peak becomes about an order of magnitude brighter because it peaks much earlier when the heating rate is larger. We also provide parametric fits for the heating rates between 0.1 and 100 days, and we provide a simple fit in Y{sub e}, s, and τ to estimate whether or not the ejecta is lanthanide-rich.

r-PROCESS LANTHANIDE PRODUCTION AND HEATING RATES IN KILONOVAE

International Nuclear Information System (INIS)

Lippuner, Jonas; Roberts, Luke F.

2015-01-01

r-process nucleosynthesis in material ejected during neutron star mergers may lead to radioactively powered transients called kilonovae. The timescale and peak luminosity of these transients depend on the composition of the ejecta, which determines the local heating rate from nuclear decays and the opacity. Kasen et al. and Tanaka and Hotokezaka pointed out that lanthanides can drastically increase the opacity in these outflows. We use the new general-purpose nuclear reaction network SkyNet to carry out a parameter study of r-process nucleosynthesis for a range of initial electron fractions Y e , initial specific entropies s, and expansion timescales τ. We find that the ejecta is lanthanide-free for Y e ≳ 0.22−0.30, depending on s and τ. The heating rate is insensitive to s and τ, but certain, larger values of Y e lead to reduced heating rates, due to individual nuclides dominating the heating. We calculate approximate light curves with a simplified gray radiative transport scheme. The light curves peak at about a day (week) in the lanthanide-free (-rich) cases. The heating rate does not change much as the ejecta becomes lanthanide-free with increasing Y e , but the light-curve peak becomes about an order of magnitude brighter because it peaks much earlier when the heating rate is larger. We also provide parametric fits for the heating rates between 0.1 and 100 days, and we provide a simple fit in Y e , s, and τ to estimate whether or not the ejecta is lanthanide-rich

CFD and Thermo Mechanical Analysis on Effect of Curved vs Step Surface in IC Engine Cylinder Head

Science.gov (United States)

Balaji, S.; Ganesh, N.; Kumarasamy, A.

2017-05-01

Current research in IC engines mainly focus on various methods to achieve higher efficiency and high specific power. As a single design parameter, combustion chamber peak spring pressure has increased more than before. Apart from the structural aspects of withstanding these loads, designer faces challenges of resolving thermal aspects of cylinder head. Methods to enhance the heat transfer without compromising load withstanding capability are being constantly explored. Conventional cylinder heads have got sat inner surface. In this paper we have suggested a modification in inner surface to enhance the heat transfer capability. To increase the heat transfer rate, inner same deck surface is configured as a curved and stepped surface instead of sat. We have reported the effectiveness of extend of curvature in the inner same deck surface in a different technical paper. Here, we are making a direct comparison between stepped and curved surface only. From this analysis it has been observed that curved surface reduces the ame deck temperature considerably without compromising the structural strength factors compared to step and sat surface.

Heat shock and thermotolerance of Escherichia coli O157:H7 in a model beef gravy system and ground beef.

Science.gov (United States)

Juneja, V K; Klein, P G; Marmer, B S

1998-04-01

Duplicate beef gravy or ground beef samples inoculated with a suspension of a four-strain cocktail of Escherichia coli O157:H7 were subjected to sublethal heating at 46 degrees C for 15-30 min, and then heated to a final internal temperature of 60 degrees C. Survivor curves were fitted using a linear model that incorporated a lag period (TL), and D-values and 'time to a 4D inactivation' (T4D) were calculated. Heat-shocking allowed the organism to survive longer than non-heat-shocked cells; the T4D values at 60 degrees C increased 1.56- and 1.50-fold in beef gravy and ground beef, respectively. In ground beef stored at 4 degrees C, thermotolerance was lost after storage for 14 h. However, heat-shocked cells appeared to maintain their thermotolerance for at least 24 h in ground beef held to 15 or 28 degrees C. A 25 min heat shock at 46 degrees C in beef gravy resulted in an increase in the levels of two proteins with apparent molecular masses of 60 and 69 kDa. These two proteins were shown to be immunologically related to GroEL and DnaK, respectively. Increased heat resistance due to heat shock must be considered while designing thermal processes to assure the microbiological safety of thermally processed foods.

An experimental study on the heat transfer characteristics of a heat pipe heat exchanger with latent heat storage. Part II: Simultaneous charging/discharging modes

International Nuclear Information System (INIS)

Liu Zhongliang; Wang Zengyi; Ma Chongfang

2006-01-01

In this part of the paper, the performance of the simultaneous charging/discharging operation modes of the heat pipe heat exchanger with latent heat storage is experimentally studied. The experimental results show that the device may operate under either the fluid to fluid heat transfer with charging heat to the phase change material (PCM) or the fluid to fluid heat transfer with discharging heat from the PCM modes according to the initial temperature of the PCM. The melting/solidification curves, the performances of the heat pipes and the device, the influences of the inlet temperature and the mass flow rate of the cold water on the operation performance are investigated by extensive experiments. The experimental results also disclose that under the simultaneous charging/discharging operation mode, although the heat transfer from the hot water directly to the cold water may vary, it always takes up a major part of the total heat recovered by the cold water due to the very small thermal resistance compared with the thermal resistance of the PCM side. The melting/solidification processes taking place in the simultaneous charging/discharging operation are compared with those in the charging only and discharging only processes. By applying a simplified thermal resistance analysis, a criterion for predicting the exact operation modes was derived and used to explain the observed experimental phenomena

Analysis of the radial distribution curves of partially ordered condensed carbon films

International Nuclear Information System (INIS)

Palatnik, L.S.; Derevyanchenko, A.S.; Nechitajlo, A.A.; Stetsenko, A.N.; Gorbenko, N.I.

1977-01-01

The Fourier analysis of the electron scattering curves has been carried out to determine the short-range order structure of carbon condensates. The intensity curves for carbon films condensed in a approximately 10 -6 Torr vacuum upon a substrate heated up to 600 deg C were obtained by diffraction techniques with filtration of the inelastic scattered electron background. The radial distribution curve errors were analyzed and quantified with the aid of a computer to determine the short-range order of the condensed carbon. It has been shown that carbon films consist of regions measuring approximately 20 A formed by parallelly packed graphite nets with azimuthal orientation different from that in ideal graphite crystals

Heat transfer and vascular cambium necrosis in the boles of trees during surface fires

Science.gov (United States)

M. B. Dickinson

2002-01-01

Heat-transfer and cell-survival models are used to link surface fire behavior with vascular cambium necrosis from heating by flames. Vascular cambium cell survival was predicted with a numerical model based on the kinetics of protein denaturation and parameterized with data from the literature. Cell survival was predicted for vascular cambium temperature regimes...

MHD convective flow of magnetite-Fe3O4 nanoparticles by curved stretching sheet

Directory of Open Access Journals (Sweden)

Tasawar Hayat

Full Text Available Present work is devoted to convective flow of ferrofluid due to non linear stretching curved sheet. Electrically conducting fluid is considered in the presence of uniform magnetic field. Nanofluid comprises water and magnetite-Fe3O4 as nanoparticles. Thermal radiation and heat generation/absorption are explained. Homotopy concept is utilized for the development of solutions. Highly nonlinear partial differential systems are reduced into the nonlinear ordinary differential system. Impact of non-dimensional radius of curvature and power law index on the physical quantities like fluid pressure, velocity and temperature field are examined. Computations for surface shear stress and heat transfer rate also analyzed. Keywords: MHD nanofluid, Thermal radiation, Porous medium, Convective boundary conditions, Non-linear curved stretching sheet

Radiation survival of cells from spheroids grown in different oxygen concentrations

International Nuclear Information System (INIS)

Franko, A.J.; Sutherland, R.M.

1979-01-01

The position of the internal, chronically hypoxic cells in spheroids was varied by alterations in the oxygen concentration in the growth medium. Such alterations were expected to cause large changes in the size of the radiobiologically hypoxic fraction. This was tested by growing and irradiating spheroids in oxygen concentrations between 5 and 20.3%, ensuring that the irradiation and growth conditions were as similar as possible. The survival curves appeared to be linear below a surviving fraction of 3 x 10 -2 , and the slopes were intermediate between the slopes of control curves for cells from spheroids irradiated in nitrogen or when fully oxygenated. Thus direct estimates of the hypoxic fractions could not be made. Two models of oxygen diffusion might explain the data. One model assumes that a large fraction of cells was fully hypoxic (radiobiologically) and that these internal, G 1 -confined, chronically hypoxic cells had a lower inherent radioresistance than the outer proliferating cells. Evidence was presented which indicated that this model was unlikely to be correct. The other model assumes that the inherent radioresistance was equal throughout the spheroid, and that the innermost cells died before the oxygen concentration was reduced sufficiently to cause full hypoxic protection. Theoretical survival curves based on this model were generated using the measured geometries ofthe spheroids and multitarget single-hit survival theory. Acceptable agreement with the postulate that the innermost cells of spheroids die at between 0.2 and 0.4% oxygen was obtained. These data may have implications regarding the relative contributions of chronic and acute hypoxia to the fraction of hypoxic cells in tumors

Risk factors affecting survival in heart transplant patients.

Science.gov (United States)

Almenar, L; Cardo, M L; Martínez-Dolz, L; García-Palomar, C; Rueda, J; Zorio, E; Arnau, M A; Osa, A; Palencia, M

2005-11-01

Certain cardiovascular risk factors have been linked to morbidity and mortality in heart transplant (HT) patients. The sum of various risk factors may have a large cumulative negative effect, leading to a substantially worse prognosis and the need to consider whether HT is contraindicated. The objective of this study was to determine whether the risk factors usually available prior to HT result in an excess mortality in our setting that contraindicates transplantation. Consecutive patients who underwent heart transplantation from November 1987 to January 2004 were included. Heart-lung transplants, retransplants, and pediatric transplants were excluded. Of the 384 patients, 89% were men. Mean age was 52 years (range, 12 to 67). Underlying disease included ischemic heart disease (52%), idiopathic dilated cardiomyopathy (36%), valvular disease (8%), and other (4%). Variables considered risk factors were obesity (BMI >25), dyslipidemia, hypertension, prior thoracic surgery, diabetes, and history of ischemic heart disease. Survival curves by number of risk factors using Kaplan-Meier and log-rank for comparison of curves. Overall patient survival at 1, 5, 10, and 13 years was 76%, 68%, 54%, and 47%, respectively. Survival at 10 years, if fewer than two risk factors were present, was 69%; 59% if two or three factors were present; and 37% if more than three associated risk factors were present (P = .04). The presence of certain risk factors in patients undergoing HT resulted in lower survival rates. The combination of various risk factors clearly worsened outcomes. However, we do not believe this should be an absolute contraindication for transplantation.

Heat techniques in the light of the innovation curve. New technology for gas appliances and solar water heaters; Warmtetechnieken in het licht van de innovatiecurve. Nieuwe technologie gezocht voor gastoestel en zonneboilers

Energy Technology Data Exchange (ETDEWEB)

Vollebregt, R.

2012-09-15

The development, market introduction and deployment of new techniques often follows an S-shaped curve. The gas-fired boiler transformed from a conventional apparatus into the current high efficiency boiler. Will the high efficiency electricity boiler be the next breakthrough technique? The electrical and gas heat pumps are fully developed techniques, but this does not apply to their use in Dutch single-family dwellings [Dutch] De ontwikkeling, marktintroductie en toepassing van nieuwe technieken verloopt vaak volgens een S-vormige curve. De gasketel transformeerde van conventioneel toestel naar de huidige hr-ketel. Is de hre-ketel de volgende doorbraaktechniek? De elektrische en de gaswarmtepomp zijn uitontwikkelde technieken, maar nog niet voor de toepassing in een Nederlandse eengezinswoning.

Indirectly heated biomass gasification using a latent-heat ballast-part 3: refinement of the heat transfer model

International Nuclear Information System (INIS)

Cummer, Keith; Brown, Robert C.

2005-01-01

An indirectly heated gasifier is under development at Iowa State University. This gasifier integrates a latent-heat ballast with a fluidized-bed reactor. The latent heat ballast is an array of stainless-steel tubes filled with lithium fluoride, which is a high-temperature phase-change material (PCM). Previous studies have presented experimental results from the gasifier and described a mathematical model of the pyrolysis phase of the cyclic gasification process. This model considers both heat transfer and chemical reactions that occur during pyrolysis, but discrepancies between model predictions and experimental data have demonstrated the need to refine the model. In particular, cooling curves for the ballasting system are not well predicted during phase change of the lithium fluoride. A reformulated model, known as the Receding Interface (RI) model, postulates the existence of a receding liquid phase within the ballast tubes as they cool, which progressively decreases the rate of heat transfer from the tubes. The RI model predicts behavior that is more consistent with experimental results during the phase-change process, while retaining accuracy before and after the process of phase change

Applications of Artificial Neural Network for the Prediction of Pool Boiling Curves

International Nuclear Information System (INIS)

Su, Guanghui; Fukuda, K.; Morita, K.

2002-01-01

Artificial neural network (ANN) has the advantage that the best-fit correlations of experimental data will no longer be necessary for predicting unknowns from the known parameters. The ANN was applied to predict the pool boiling curves in this paper. The database of experimental data presented by Berenson, Dhuga et al., and Bui and Dhir etc. were used in the analysis. The database is subdivided in two subsets. The first subset is used to train the network and the second one is used to test the network after the training process. The input parameters of the ANN are: wall superheat ΔT w , surface roughness, steady/transient heating/transient cooling, subcooling, Surface inclination and pressure. The output parameter is heat flux q. The proposed methodology allows us to achieve the accuracy that satisfies the user's convergence criterion and it is suitable for pool boiling curve data processing. (authors)

Impact of Chlorine and Heat on the Survival of Hartmannella vermiformis and Subsequent Growth of Legionella pneumophila.

Science.gov (United States)

Kuchta, J M; Navratil, J S; Shepherd, M E; Wadowsky, R M; Dowling, J N; States, S J; Yee, R B

1993-12-01

Hartmannella vermiformis, a common amoebal inhabitant of potable-water systems, supports intracellular multiplication of Legionella pneumophila and is probably important in the transportation and amplification of legionellae within these systems. To provide a practical guide for decontamination of potable-water systems, we assessed the chlorine and heat resistance of H. vermiformis. H. vermiformis cysts and trophozoites were treated independently with chlorine at concentrations of 2.0 to 10.0 ppm for 30 min and then cocultured with L. pneumophila. Both cysts and trophozoites were sensitive to concentrations between 2.0 and 4.0 ppm and above (trophozoites somewhat more so than cysts), and 10.0 ppm was lethal to both forms. Hartmannellae treated with chlorine up to a concentration of 4.0 ppm supported the growth of legionellae. To determine whether heat would be an effective addendum to chlorine treatment of amoebae, hartmannellae were subjected to temperatures of 55 and 60 degrees C for 30 min and alternatively to 50 degrees C followed by treatment with chlorine at a concentration of 2 ppm. Fewer than 0.05% of the amoebae survived treatment at 55 degrees C, and there were no survivors at 60 degrees C. Pretreatment at 50 degrees C appeared to make hartmannella cysts more susceptible to chlorine but did not further reduce the concentration of trophozoites.

Survival of irradiated glia and glioma cells studied with a new cloning technique

International Nuclear Information System (INIS)

Nilsson, S.; Carlsson, J.; Larsson, B.; Ponten, J.

1980-01-01

A method allowing cloning of monolayer cultured cells with a low plating efficiency was developed. Cells were grown in several small palladium squares to obtain a high cell density. These squares were surrounded by non-adhesive agarose to prevent large distance migration and thereby mixing of the clones. By using easily-cloned hamster cells for comparison it was found that the survival curves were similar to the curves obtained with conventional cloning. The new method was used to compare the radiosensitivity of cultured human glia and glioma cells which both have a low plating efficiency ( 0 -values (1.5 to 2.5 Gy) and large shoulders (extrapolation numbers around 5) indicating that they were rather resistant and had a high capacity for accumulation of sublethal damage. The survival curves for glia cells had lower D 0 -values (1.3 to 1.5 Gy) and no shoulders at all, indicating that they were more sensitive than the glioma cells. (author)

Exploring the potential of acquisition curves of the anhysteretic remanent magnetization as a tool to detect subtle magnetic alteration induced by heating

Science.gov (United States)

de Groot, Lennart V.; Dekkers, Mark J.; Mullender, Tom A. T.

2012-03-01

Recently, many new methods and improved protocols to determine the absolute paleointensity of lavas reliably have been proposed. Here we study eight recent flows from three different volcanic edifices (Mt. Etna, La Palma and Hawaii) with the so-called multispecimen parallel differential pTRM (MSP) method including the recently proposed domain-state correction (MSP-DSC) (Fabian and Leonhardt, 2010). Surprisingly, apart from approximately correct paleointensity values, we observe major underestimates of the paleofield. These deviations are possibly related to alteration that is not revealed by rock-magnetic analysis. We explore the potential of high-resolution acquisition curves of the anhysteretic remanent magnetization (ARM) to detect subtle alteration in the samples. It appears that assessing changes in the ARM acquisition properties before and after heating to the desired MSP temperature discriminates between underestimates and approximately correct estimations of the paleofield in the outcomes of the MSP-DSC protocol. By combining observations from the domain-state corrected MSP protocol and ARM acquisition experiments before and after heating, an extended MSP protocol is suggested which makes it possible to assess the best set temperature for the MSP-DSC protocol and to label MSP results as being approximately correct, or an underestimate of the paleofield.

Sensing the Heat Stress by Mammalian Cells

OpenAIRE

Cates Jordan; Graham Garrett C; Omattage Natalie; Pavesich Elizabeth; Setliff Ian; Shaw Jack; Smith Caitlin; Lipan Ovidiu

2011-01-01

Abstract Background The heat-shock response network controls the adaptation and survival of the cell against environmental stress. This network is highly conserved and is connected with many other signaling pathways. A key element of the heat-shock network is the heat-shock transcription factor-1 (HSF), which is transiently activated by elevated temperatures. HSF translocates to the nucleus upon elevated temperatures, forming homotrimeric complexes. The HSF homotrimers bind to the heat shock ...

Response of the microtubular cytoskeleton following hyperthermia as a prognostic indicator of survival of Chinese hamster ovary cells

International Nuclear Information System (INIS)

Coss, Ronald A.; Alden, Mark E.; Wachsberger, Phyllis R.; Smith, Nancy N.

1996-01-01

Purpose: The response of the microtubular (MT) cytoskeleton to hyperthermia was assessed as a prognostic indicator of cytotoxicity. Methods and Materials: Heat-induced collapse and subsequent recovery of the MT system were compared with survival for both nonthermotolerant (NT) and thermotolerant (TT) G1 populations of Chinese hamster ovary (CHO) cells. The response of the MT system was monitored using immunofluorescence staining. The G1 populations of NT and TT cells were heated by submersion in 45.0 and 43.0 deg. C waterbaths. Results: Heat-induced perinuclear collapse of the MT system did not correlate with survival for the NT and TT populations. However, recovery of the organization of the MT cytoskeleton was correlatable with survival. The regression line of survival plotted as a function of MT recovery is fit by: y = -0.43 + 1.03x, r 2 = 0.95 (p < 0.0005). Conclusion: Restoration of the organization of the MT cytoskeleton following hyperthermia may be used as a prognostic indicator of survival of CHO cells heated in G1

Cell survival and radiation induced chromosome aberrations. Pt. 2

International Nuclear Information System (INIS)

Bauchinger, M.; Schmid, E.; Braselmann, H.

1986-01-01

Human peripheral lymphocytes were irradiated in whole blood with 0.5-4.0 Gy of 220 kVp X-rays and the frequency of chromosome aberrations was determined in 1st or 2nd division metaphases discriminated by fluorescence plus giemsa staining. Using the empirical distributions of aberrations among cells, cell survival and transmission of aberrations were investigated. Considering both daughter cells, we found that 20% of fragments and 55% of dicentrics or ring chromosomes are lost during the 1st cell division; i.e. cell survival rate from 1st to 2nd generation is mainly influenced by anaphase bridging of these two-hit aberrations. Cell survival to 2nd mitosis was calculated considering this situation and compared with the survival derived from the fraction of M1 cells without unstable aberrations. The resulting shouldered survival curves showed significantly different slopes, indicating that cell reproductive death is overestimated in the latter approach. (orig.)

Experimental investigation of heat transfer in the transition region

International Nuclear Information System (INIS)

Johannsen, K.; Weber, P.; Feng, Q.

1990-10-01

An experimental study of forced convective boiling heat transfer for upflow of water in a circular tube has been performed using a heat transfer system with temperature-controlled indirect Joule heating. By this way, complete boiling curves from incipience of boiling to fully established film boiling could be measured including the transition boiling regime. The boiling curves were traversed in a quasi-steady mode, usually by increasing the set-point wall temperature average at a constant time rate of 3.5 K/min. The vast majority of results covers the pressure range from 0.1 to 1.0 MPa, mass flux range from 25 to 200 kg/(m 2 s) and inlet subcooling from 5 to 30 K. The experimental results of transition boiling heat transfer obtained in the centre of the test section were correlated in terms of a heat flux/surface superheat relationship that was normalized by the maximum heat flux (local CHF) and its associated wall superheat, respectively, to anchor the transition boiling curve to its low temperature limit. The upper surface temperature limit of the transition boiling regime was determined by inspection of measured axial distributions of surface heat flux and corresponding wall temperature. The critical heat flux (CHF) and its corresponding wall superheat has been measured, too. These temperature-controlled results were compared also with power-controlled experiments. The data are presented in terms of a table and accurate empirical correlations following Katto's generalized correlation scheme. Taking into account previous CHF data at L/D ≤ 100 and same range of flow conditions the length effect was found to further depend on pressure and mass flux. The data for the critical wall superheat show a distinct dependence upon pressure, mass flux and inlet quality that has not been observed before with comparable clarity

An Information Survival Kit for the Prospective Geothermal Heat Pump Owner

Energy Technology Data Exchange (ETDEWEB)

Rafferty, Kevin

2001-02-01

The fact that you are considering a geothermal (or ground-source) heat pump system, places you among the best informed and most innovative homeowners in the country. Geothermal heat pumps (GHPs), although not a new technology, remain a small (but growing) player in the residential heating/cooling sector. Although somewhat higher in first cost, this technology can, in the right application, quickly repay this cost premium through savings in energy costs. Despite all the positive publicity on GHPs, they are not for everyone. Like any other heating and cooling system, GHPs tend to fit well in certain circumstances and poorly in others. Familiarizing yourself with the factors that effect the feasibility of GHPs will assist you in making an informed decision as to their suitability for your home. It is the intention of this package to provide that information and to address some of the commonly asked questions regarding the technology. Please feel free to contact us if you have questions not covered in this package.

Influence of insulin on heat (450) protection by hexose sugars

International Nuclear Information System (INIS)

Sandifer, L.; Nagle, W.A.; Henle, K.J.; Moss, A.J. Jr.

1987-01-01

Treatment of cultured cells with 100mM D-glucose and D-galactose confers protection against hyperthermia-induced cell death, but the mechanism is not known. The authors measured changes in cell survival and altered levels of intracellular sugar metabolites in Chinese hamster fibroblast (V79) cells. Cells were incubated at 37 0 for 1 or 5 hours prior to a 45 0 heating in balanced salts solution (BSS) with 2mM glutamine and varying concentrations of sugars in the presence and absence of insulin (10 gm/ml). Cells incubated at all sugar concentrations (5-125mM) with insulin showed a more rapid increase in survival: after 17 min. at 45 0 the survival with 125mM sugar plus insulin yielded a 4 fold increase after a 1 or 5 hour incubation. Longer incubation times were required for increased survival in the absence of insulin. The authors also observed increased survival, relative to cells heated in complete medium, for cells incubated in BSS with 2mM glutamine and no sugar. This suggests that glutamine metabolism may lead to an increase in cell heat resistance. These survival results will be related to intracellular changes in sugar metabolites, principally sugar phosphates

Prognostic and survival analysis of presbyopia: The healthy twin study

Science.gov (United States)

Lira, Adiyani; Sung, Joohon

2015-12-01

Presbyopia, a vision condition in which the eye loses its flexibility to focus on near objects, is part of ageing process which mostly perceptible in the early or mid 40s. It is well known that age is its major risk factor, while sex, alcohol, poor nutrition, ocular and systemic diseases are known as common risk factors. However, many other variables might influence the prognosis. Therefore in this paper we developed a prognostic model to estimate survival from presbyopia. 1645 participants which part of the Healthy Twin Study, a prospective cohort study that has recruited Korean adult twins and their family members based on a nation-wide registry at public health agencies since 2005, were collected and analyzed by univariate analysis as well as Cox proportional hazard model to reveal the prognostic factors for presbyopia while survival curves were calculated by Kaplan-Meier method. Besides age, sex, diabetes, and myopia; the proposed model shows that education level (especially engineering program) also contribute to the occurrence of presbyopia as well. Generally, at 47 years old, the chance of getting presbyopia becomes higher with the survival probability is less than 50%. Furthermore, our study shows that by stratifying the survival curve, MZ has shorter survival with average onset time about 45.8 compare to DZ and siblings with 47.5 years old. By providing factors that have more effects and mainly associate with presbyopia, we expect that we could help to design an intervention to control or delay its onset time.

Theoretical study of melting curves on Ta, Mo, and W at high pressures

Energy Technology Data Exchange (ETDEWEB)

Xi Feng [Laboratory for Shock Wave and Detonation Physics Research, Institute of Fluid Physics, P.O. Box 919-102, 621900 Mianyang (China)], E-mail: hawk_0816@yahoo.com.cn; Cai Lingcang [Laboratory for Shock Wave and Detonation Physics Research, Institute of Fluid Physics, P.O. Box 919-102, 621900 Mianyang (China)

2008-06-01

The melting curves of tantalum (Ta), molybdenum (Mo), and tungsten (W) are calculated using a dislocation-mediated melting model. The calculated melting curves are in good agreement with shock-wave data, and partially in agreement with wire explosion and piston-cylinder data, but show large discrepancies with diamond-anvil cell (DAC) data. We propose that the melting mechanism caused by shock-wave and laser-heated DAC techniques are probably different, and that a systematic difference exists in the two melting processes.

Performance of heat engines with non-zero heat capacity

International Nuclear Information System (INIS)

Odes, Ron; Kribus, Abraham

2013-01-01

Highlights: ► Finite heat capacity is a second irreversibility mechanism in addition to thermal resistance. ► Heat capacity introduces thermal transients and reverse heat flow. ► Engine maximum power and efficiency are lower for finite heat capacity. ► Implementing the optimal engine cycle requires active control. - Abstract: The performance of a heat engine is analyzed subject to two types of irreversibility: a non-zero heat capacity, together with the more common finite heat transfer rate between the engine and the external heat reservoirs. The heat capacity represents an engine body that undergoes significant temperature variations during the engine cycle. An option to cut off the heat exchange between the engine and the external surrounding for part of the engine cycle is also explored. A variational approach was taken to find the engine’s internal temperature profile (which defines the internal thermodynamic cycle) that would produce maximum power. The maximum power is shown to be lower than the case of zero heat capacity, due to a loss of heat that is stored in the engine body and then lost, bypassing the thermodynamic cycle. The maximum efficiency and the efficiency at maximum power are also lower than the zero heat capacity case. Similar to the Curzon–Ahlborn analysis, power can be traded for increased efficiency, but for high heat capacity, the range of efficiency that is available for such a trade is diminished. Isolating the engine during part of the cycle reduces maximum power, but the efficiency at maximum power and the maximum efficiency are improved, due to better exploitation of heat stored in the engine body. This might be useful for real engines that are limited by the internal energy change during a single engine cycle or by the operating frequency, leading to a broader power–efficiency curve.

Numerical investigation of nucleate pool boiling heat transfer

Directory of Open Access Journals (Sweden)

Stojanović Andrijana D.

2016-01-01

Full Text Available Multidimensional numerical simulation of the atmospheric saturated pool boiling is performed. The applied modelling and numerical methods enable a full representation of the liquid and vapour two-phase mixture behaviour on the heated surface, with included prediction of the swell level and heated wall temperature field. In this way the integral behaviour of nucleate pool boiling is simulated. The micro conditions of bubble generation at the heated wall surface are modelled by the bubble nucleation site density, the liquid wetting contact angle and the bubble grow time. The bubble nucleation sites are randomly located within zones of equal size, where the number of zones equals the nucleation site density. The conjugate heat transfer from the heated wall to the liquid is taken into account in wetted heated wall areas around bubble nucleation sites. The boiling curve relation between the heat flux and the heated wall surface temperature in excess of the saturation temperature is predicted for the pool boiling conditions reported in the literature and a good agreement is achieved with experimentally measured data. The influence of the nucleation site density on the boiling curve characteristic is confirmed. In addition, the influence of the heat flux intensity on the spatial effects of vapour generation and two-phase flow are shown, such as the increase of the swell level position and the reduced wetting of the heated wall surface by the heat flux increase. [Projekat Ministarstva nauke Republike Srbije, br. TR-33018 i br. OI-174014

HEATING OF FLARE LOOPS WITH OBSERVATIONALLY CONSTRAINED HEATING FUNCTIONS

Energy Technology Data Exchange (ETDEWEB)

Qiu Jiong; Liu Wenjuan; Longcope, Dana W. [Department of Physics, Montana State University, Bozeman, MT 59717-3840 (United States)

2012-06-20

We analyze high-cadence high-resolution observations of a C3.2 flare obtained by AIA/SDO on 2010 August 1. The flare is a long-duration event with soft X-ray and EUV radiation lasting for over 4 hr. Analysis suggests that magnetic reconnection and formation of new loops continue for more than 2 hr. Furthermore, the UV 1600 Angstrom-Sign observations show that each of the individual pixels at the feet of flare loops is brightened instantaneously with a timescale of a few minutes, and decays over a much longer timescale of more than 30 minutes. We use these spatially resolved UV light curves during the rise phase to construct empirical heating functions for individual flare loops, and model heating of coronal plasmas in these loops. The total coronal radiation of these flare loops are compared with soft X-ray and EUV radiation fluxes measured by GOES and AIA. This study presents a method to observationally infer heating functions in numerous flare loops that are formed and heated sequentially by reconnection throughout the flare, and provides a very useful constraint to coronal heating models.

[The survival prediction model of advanced gallbladder cancer based on Bayesian network: a multi-institutional study].

Science.gov (United States)

Tang, Z H; Geng, Z M; Chen, C; Si, S B; Cai, Z Q; Song, T Q; Gong, P; Jiang, L; Qiu, Y H; He, Y; Zhai, W L; Li, S P; Zhang, Y C; Yang, Y

2018-05-01

Objective: To investigate the clinical value of Bayesian network in predicting survival of patients with advanced gallbladder cancer(GBC)who underwent curative intent surgery. Methods: The clinical data of patients with advanced GBC who underwent curative intent surgery in 9 institutions from January 2010 to December 2015 were analyzed retrospectively.A median survival time model based on a tree augmented naïve Bayes algorithm was established by Bayesia Lab software.The survival time, number of metastatic lymph nodes(NMLN), T stage, pathological grade, margin, jaundice, liver invasion, age, sex and tumor morphology were included in this model.Confusion matrix, the receiver operating characteristic curve and area under the curve were used to evaluate the accuracy of the model.A priori statistical analysis of these 10 variables and a posterior analysis(survival time as the target variable, the remaining factors as the attribute variables)was performed.The importance rankings of each variable was calculated with the polymorphic Birnbaum importance calculation based on the posterior analysis results.The survival probability forecast table was constructed based on the top 4 prognosis factors. The survival curve was drawn by the Kaplan-Meier method, and differences in survival curves were compared using the Log-rank test. Results: A total of 316 patients were enrolled, including 109 males and 207 females.The ratio of male to female was 1.0∶1.9, the age was (62.0±10.8)years.There was 298 cases(94.3%) R0 resection and 18 cases(5.7%) R1 resection.T staging: 287 cases(90.8%) T3 and 29 cases(9.2%) T4.The median survival time(MST) was 23.77 months, and the 1, 3, 5-year survival rates were 67.4%, 40.8%, 32.0%, respectively.For the Bayesian model, the number of correctly predicted cases was 121(≤23.77 months) and 115(>23.77 months) respectively, leading to a 74.86% accuracy of this model.The prior probability of survival time was 0.503 2(≤23.77 months) and 0.496 8

Evaluation of heat transfer enhancement in air-heating collectors

Energy Technology Data Exchange (ETDEWEB)

Mattox, D. L.

1979-06-01

The present research effort was initiated for the purpose of increasing the thermal efficiency of air heating solar collectors through identification and development of optimum design and operation criteria for solar absorber-to-air heat exchangers. Initially this effort took the form of a solar collector systems analysis to evaluate the impact of various techniques for enhancing the heat transfer between the absorber and air stream on overall thermal performance of the entire solar collector. This systems analysis resulted in the selection of solar collector designs providing ducted cooling air on the absorber shaded side as a base line. A transient heat transfer analysis of a complete solar air heating collector was used to demonstrate that an optimum absorber-to-air heat exchanger design could be provided with several interrupted fin configurations. Additional analyses were performed to establish that the maximum solar collector thermal performance to required pumping power was realized for a Reynolds number range of 1000 to 2000. This Reynolds number range was used to establish a theoretical design limit curve for maximum thermal performance versus required pumping power for all interrupted fin designs as published in the open literature. Heat and momentum transfer empirical relationships were defined for scaling the state-of-the-art high conductance fin designs identified from a compact configuration to the less compact designs needed for solar collectors.

Development of a Summarized Health Index (SHI for use in predicting survival in sea turtles.

Directory of Open Access Journals (Sweden)

Tsung-Hsien Li

Full Text Available Veterinary care plays an influential role in sea turtle rehabilitation, especially in endangered species. Physiological characteristics, hematological and plasma biochemistry profiles, are useful references for clinical management in animals, especially when animals are during the convalescence period. In this study, these factors associated with sea turtle surviving were analyzed. The blood samples were collected when sea turtles remained alive, and then animals were followed up for surviving status. The results indicated that significantly negative correlation was found between buoyancy disorders (BD and sea turtle surviving (p < 0.05. Furthermore, non-surviving sea turtles had significantly higher levels of aspartate aminotranspherase (AST, creatinine kinase (CK, creatinine and uric acid (UA than surviving sea turtles (all p < 0.05. After further analysis by multiple logistic regression model, only factors of BD, creatinine and UA were included in the equation for calculating summarized health index (SHI for each individual. Through evaluation by receiver operating characteristic (ROC curve, the result indicated that the area under curve was 0.920 ± 0.037, and a cut-off SHI value of 2.5244 showed 80.0% sensitivity and 86.7% specificity in predicting survival. Therefore, the developed SHI could be a useful index to evaluate health status of sea turtles and to improve veterinary care at rehabilitation facilities.

Thermal and Mechanical Buckling and Postbuckling Responses of Selected Curved Composite Panels

Science.gov (United States)

Breivik, Nicole L.; Hyer, Michael W.; Starnes, James H., Jr.

1998-01-01

The results of an experimental and numerical study of the buckling and postbuckling responses of selected unstiffened curved composite panels subjected to mechanical end shortening and a uniform temperature increase are presented. The uniform temperature increase induces thermal stresses in the panel when the axial displacement is constrained. An apparatus for testing curved panels at elevated temperature is described, numerical results generated by using a geometrically nonlinear finite element analysis code are presented. Several analytical modeling refinements that provide more accurate representation of the actual experimental conditions, and the relative contribution of each refinement, are discussed. Experimental results and numerical predictions are presented and compared for three loading conditions including mechanical end shortening alone, heating the panels to 250 F followed by mechanical end shortening, and heating the panels to 400 F. Changes in the coefficients of thermal expansion were observed as temperature was increased above 330 F. The effects of these changes on the experimental results are discussed for temperatures up to 400 F.

Isochronous relaxation curves for type 304 stainless steel after monotonic and cyclic strain

International Nuclear Information System (INIS)

Swindeman, R.W.

1978-01-01

Relaxation tests to 100 hr were performed on type 304 stainless steel in the temperature range 480 to 650 0 C and were used to develop isochronous relaxation curves. Behavior after monotonic and cyclic strain was compared. Relaxation differed only slightly as a consequence of the type of previous strain, provided that plastic flow preceded the relaxation period. We observed that the short-time relaxation behavior did not manifest strong heat-to-heat variation in creep strength

Understanding survival analysis: Kaplan-Meier estimate.

Science.gov (United States)

Goel, Manish Kumar; Khanna, Pardeep; Kishore, Jugal

2010-10-01

Kaplan-Meier estimate is one of the best options to be used to measure the fraction of subjects living for a certain amount of time after treatment. In clinical trials or community trials, the effect of an intervention is assessed by measuring the number of subjects survived or saved after that intervention over a period of time. The time starting from a defined point to the occurrence of a given event, for example death is called as survival time and the analysis of group data as survival analysis. This can be affected by subjects under study that are uncooperative and refused to be remained in the study or when some of the subjects may not experience the event or death before the end of the study, although they would have experienced or died if observation continued, or we lose touch with them midway in the study. We label these situations as censored observations. The Kaplan-Meier estimate is the simplest way of computing the survival over time in spite of all these difficulties associated with subjects or situations. The survival curve can be created assuming various situations. It involves computing of probabilities of occurrence of event at a certain point of time and multiplying these successive probabilities by any earlier computed probabilities to get the final estimate. This can be calculated for two groups of subjects and also their statistical difference in the survivals. This can be used in Ayurveda research when they are comparing two drugs and looking for survival of subjects.

Effect of low fluencies of near-ultraviolet radiation on Bacteroides fragilis survival

International Nuclear Information System (INIS)

Slade, H.J.K.; Jones, D.T.; Woods, D.R.

1982-01-01

Bacteroides fragilis is a convenient obligate anaerobe for an investigation on the effect of near-UV irradiation since the authors have shown that it can be maintained in aerobic solutions for at least 6 h without loss in viability. Furthermore, they recently demonstrated that B. fragilis differs from other bacteria in that it is more sensitive to far-UV (254 nm) radiation in the presence of oxygen. The role of oxygen on near-UV survival in B. fragilis, was investigated. The effect of chloramphenicol was also studied. Survival curves are presented. B. fragilis Bf-2 cells irradiated with increasing fluencies of near-UV light under anaerobic conditions showed no loss in viability. A 'V'-shaped survival curve was obtained when cells were irradiated aerobically. After the initial reduction in viability with fluencies up to 1.5 kJ/m 2 further irradiation resulted in the recovery of colony-forming ability which was maximal at 2.6 kJ/m 2 and remained at this level up to fluencies of 4 kJ/m 2 . (Auth.)

Can cell survival parameters be deduced from non-clonogenic assays of radiation damage to normal tissue

International Nuclear Information System (INIS)

Michalowski, A.; Wheldon, T.E.; Kirk, J.

1984-01-01

The relationship between dose-response curves for large scale radiation injury to tissues and survival curves for clonogenic cells is not necessarily simple. Sterilization of clonogenic cells occurs near-instantaneously compared with the protracted lag period for gross injury to tissues. Moreover, with some types of macroscopic damage, the shapes of the dose-response curves may depend on time of assay. Changes in the area or volume of irradiated tissue may also influence the shapes of these curves. The temporal pattern of expression of large scale injury also varies between tissues, and two distinct groups can be recognized. In rapidly proliferating tissues, lag period is almost independent of dose, whilst in slowly proliferating tissues, it is inversely proportional to dose. This might be explained by invoking differences in corresponding proliferative structures of the tissues. (Three compartmental Type H versus one compartmental Type F proliferative organization). For the second group of tissues particularly, mathematical modelling suggests a systematic dissociation of the dose-response curves for clonogenic cell survival and large scale injury. In particular, it may be difficult to disentangle the contributions made to inter-fraction sparing by cellular repair processes and by proliferation-related factors. (U.K.)

Fuel savings with conventional hot water space heating systems by incorporating a natural gas powered heat pump. Preliminary project: Development of heat pump technology

Science.gov (United States)

Vanheyden, L.; Evertz, E.

1980-12-01

Compression type air/water heat pumps were developed for domestic heating systems rated at 20 to 150 kW. The heat pump is driven either by a reciprocating piston or rotary piston engine modified to operate on natural gas. Particular features of natural gas engines as prime movers, such as waste heat recovery and variable speed, are stressed. Two systems suitable for heat pump operation were selected from among five different mass produced car engines and were modified to incorporate reciprocating piston compressor pairs. The refrigerants used are R 12 and R 22. Test rig data transferred to field conditions show that the fuel consumption of conventional boilers can be reduced by 50% and more by the installation of engine driven heat pumps. Pilot heat pumps based on a 1,600 cc reciprocating piston engine were built for heating four two-family houses. Pilot pump operation confirms test rig findings. The service life of rotary piston and reciprocating piston engines was investigated. The tests reveal characteristic curves for reciprocating piston engines and include exhaust composition measurements.

Reducing heat loss from the energy absorber of a solar collector

Science.gov (United States)

Chao, Bei Tse; Rabl, Ari

1976-01-01

A device is provided for reducing convective heat loss in a cylindrical radiant energy collector. It includes a curved reflective wall in the shape of the arc of a circle positioned on the opposite side of the exit aperture from the reflective side walls of the collector. Radiant energy exiting the exit aperture is directed by the curved wall onto an energy absorber such that the portion of the absorber upon which the energy is directed faces downward to reduce convective heat loss from the absorber.

The thermoluminescent curve as parameter to compare archaeological ceramics

International Nuclear Information System (INIS)

Dominguez R, I.R.; Ramirez C, G.A.; Gonzalez M, P.R.; Mendoza A, D.; Martinez C, G.

2006-01-01

Most mineral materials, including the constituents of pottery, have the property of thermoluminescence (TL), where part of the energy from radioactive decay in the mineral is stored and later released as light upon strong heating. The intensity of emitted light as a function of temperature is the thermoluminescence glow curve. However, it is well-know the thermoluminescence glow curve form depends of several factors associates with the incident radiation and type of materials. Between the factors associated with the materials, it can be mentioned the quantity and type of crystalline phases, and quantity and type of impurities that they could be present in the material. That is to say, materials with different physicochemical characteristics will produce different thermoluminescence glow curve, although, they have been irradiated under the same conditions. In accordance with the above mentioned, it is possible to identified differences between pre hispanic ceramic belonging to a same site and other sites. In this work a discussion about advantages and disadvantages is presented. Some specific examples in ceramic artifacts belonging to the Matlatzinca and Teotihuacan cultures are included. (Author)

q-deformed Einstein's model to describe specific heat of solid

Science.gov (United States)

Guha, Atanu; Das, Prasanta Kumar

2018-04-01

Realistic phenomena can be described more appropriately using generalized canonical ensemble, with proper parameter sets involved. We have generalized the Einstein's theory for specific heat of solid in Tsallis statistics, where the temperature fluctuation is introduced into the theory via the fluctuation parameter q. At low temperature the Einstein's curve of the specific heat in the nonextensive Tsallis scenario exactly lies on the experimental data points. Consequently this q-modified Einstein's curve is found to be overlapping with the one predicted by Debye. Considering only the temperature fluctuation effect(even without considering more than one mode of vibration is being triggered) we found that the CV vs T curve is as good as obtained by considering the different modes of vibration as suggested by Debye. Generalizing the Einstein's theory in Tsallis statistics we found that a unique value of the Einstein temperature θE along with a temperature dependent deformation parameter q(T) , can well describe the phenomena of specific heat of solid i.e. the theory is equivalent to Debye's theory with a temperature dependent θD.

The survival effects of V79 cells irradiated with carbon ions in different let

International Nuclear Information System (INIS)

Wang Jufang; Zhou Guangming; He Jing; Li Wenjian; Li Qiang; Dang Bingrong; Li Xinglin; Weng Xiaoqiong; Xie Hongmei; Wei Zengquan; Gao Qingxiang

2001-01-01

The survival of cultured Chinese V79 hamster cells irradiated with carbon ions with different LETs were investigated. Irradiation was performed at the heavy Ion Research Facility in Lanzhou (HIRFL). Results were compared with those obtained from the experiments with γ rats and could be concluded as follows: The survival curves for carbon ions showed as straight lines and were fitted to the one-target one-hit model, but for γ rays the curves with shoulders were fitted to the multi-target one-hit model. As the LETs were 125, 200 and 700 keV/μm for carbon ions, the inactivation cross section 35, 12 and 8 μm 2 , respectively, which suggested that under the experimental conditions, the lower the LET of carbon ions, the more seriously the irradiation killed cells. In the case of 125 keV/μm, the RBEs of carbon ions at the 0.1 and 0.37 survival levels were 1.47 and 2.19 respectively

The effect of an asynchronous population of cells on the initial slope of dose-effect curves

International Nuclear Information System (INIS)

Chadwick, K.H.; Leenhouts, H.P.

1975-01-01

The molecular theory of cell survival gives an equation S = exp [ -p(αD + β D 2 )] which can be used to analyse dose-effect curves for synchronized cells. The variation in the coefficients α and β through the cell cycle has been found to be consistent for the different radiation types and is compatible with the induction of DNA double-strand breaks which is assumed in the theory to be the mechanism which is responsible for the biological effect. The theory predicts that low-LET radiation will have an initial slope, given by the coefficient α, and the consistency of the analysis of synchronized cell survival substantiates this prediction. In the molecular theory the induction of mutations has also been proposed to arise from DNA double-strand breaks and to be represented by the equation M = 1 - exp [-q(αD + β D 2 )]. This implies that at low doses of low-LET radiation the radiobiological effect will be linear with dose and that high-dose results may be analysed to provide estimates of the radiosensitivity of cells to low doses of radiation for radiological protection purposes. In an asynchronous population of cells it is possible that a small proportion of very radiosensitive cells can lead to significant deviations from this straightforward analysis. This 'Oftedal effect' is applied using the molecular theory to give a general theoretical relationship between the induction of mutations and cell survival. The theoretical relationship is compared with experimental data available from the literature. It is concluded that the initial slope of a mutation or cancer induction curve may be more relevant to the determination of the radiation sensitivity at low doses than the initial slope of a survival curve. (author)

Heat shock protection against cold stress of Drosophila melanogaster

OpenAIRE

Burton, Vicky; Mitchell, Herschel K.; Young, Patricia; Petersen, Nancy S.

1988-01-01

Heat shock protein synthesis can be induced during recovery from cold treatment of Drosophila melanogaster larvae. Survival of larvae after a cold treatment is dramatically improved by a mild heat shock just before the cold shock. The conditions which induce tolerance to cold are similar to those which confer tolerance to heat.

CFD Extraction of Heat Transfer Coefficient in Cryogenic Propellant Tanks

Science.gov (United States)

Yang, H. Q.; West, Jeff

2015-01-01

Current reduced-order thermal model for cryogenic propellant tanks is based on correlations built for flat plates collected in the 1950's. The use of these correlations suffers from inaccurate geometry representation; inaccurate gravity orientation; ambiguous length scale; and lack of detailed validation. This study uses first-principles based CFD methodology to compute heat transfer from the tank wall to the cryogenic fluids and extracts and correlates the equivalent heat transfer coefficient to support reduced-order thermal model. The CFD tool was first validated against available experimental data and commonly used correlations for natural convection along a vertically heated wall. Good agreements between the present prediction and experimental data have been found for flows in laminar as well turbulent regimes. The convective heat transfer between the tank wall and cryogenic propellant, and that between the tank wall and ullage gas were then simulated. The results showed that the commonly used heat transfer correlations for either vertical or horizontal plate over-predict heat transfer rate for the cryogenic tank, in some cases by as much as one order of magnitude. A characteristic length scale has been defined that can correlate all heat transfer coefficients for different fill levels into a single curve. This curve can be used for the reduced-order heat transfer model analysis.

MicroRNA160 Modulates Plant Development and Heat Shock Protein Gene Expression to Mediate Heat Tolerance in Arabidopsis

Directory of Open Access Journals (Sweden)

Jeng-Shane Lin

2018-02-01

Full Text Available Global warming is causing a negative impact on plant growth and adversely impacts on crop yield. MicroRNAs (miRNAs are critical in regulating the expression of genes involved in plant development as well as defense responses. The effects of miRNAs on heat-stressed Arabidopsis warrants further investigation. Heat stress increased the expression of miR160 and its precursors but considerably reduced that of its targets, ARF10, ARF16, and ARF17. To study the roles of miR160 during heat stress, transgenic Arabidopsis plants overexpressing miR160 precursor a (160OE and artificial miR160 (MIM160, which mimics an inhibitor of miR160, were created. T-DNA insertion mutants of miR160 targets were also used to examine their tolerances to heat stress. Results presented that overexpressing miR160 improved seed germination and seedling survival under heat stress. The lengths of hypocotyl elongation and rachis were also longer in 160OE than the wild-type (WT plants under heat stress. Interestingly, MIM160 plants showed worse adaption to heat. In addition, arf10, arf16, and arf17 mutants presented similar phenotypes to 160OE under heat stress to advance abilities of thermotolerance. Moreover, transcriptome and qRT-PCR analyses revealed that HSP17.6A, HSP17.6II, HSP21, and HSP70B expression levels were regulated by heat in 160OE, MIM160, arf10, arf16, and arf17 plants. Hence, miR160 altered the expression of the heat shock proteins and plant development to allow plants to survive heat stress.

KINETICS PROCESSES OF DEHYDRATION AND HEATING FISH DURING FRYING, DURING SEMI HOT AND HOT SMOKING

Directory of Open Access Journals (Sweden)

V. A. Pokholchenko

2014-01-01

Full Text Available Summary. Calculated methods of graphing of curves for kinetics of dehydration and fish heating during the processes of frying, semi hot smoking and hot smoking have been developed. The offered methods of calculating are based on the basic regularities of heat and mass exchanges of these processes. Based on the research of the regularities of dehydration on the kinetic curves, critical points were identified, that characterize the transition from the moisture removal with lower energy of its bond with material to the removal of one with higher energy bond, also the influence of the product shrinkage on the velocity of the moisture removal. These points are characteristic for the temperature curves as well. It’s suggested for the temperature curve to be replaced by broken line that consists of three straight lines that are crossing in points, corresponded with the critical moistures and critical temperatures. Significant amount of the experimental material of the research of the kinetics of dehydration and fish heating under different modes is shown by authors in the form of generalized dependencies. The method allows modeling the processes of heating and dehydrating of fish and choosing the most rational modes based on the calculated data. The proposed technique makes it possible to construct the curves of the kinetics of heating and dehydration kinetics in processes of roasting, semi hot and hot smoked fish, which allows to optimize a particular process, design more efficient in terms of consumption of raw materials and energy technology, as well as to create better machines or upgrade existing equipment into account the relationship of heat and mass transfer processes.

Product differentiation by analysis of DNA melting curves during the polymerase chain reaction.

Science.gov (United States)

Ririe, K M; Rasmussen, R P; Wittwer, C T

1997-02-15

A microvolume fluorometer integrated with a thermal cycler was used to acquire DNA melting curves during polymerase chain reaction by fluorescence monitoring of the double-stranded DNA specific dye SYBR Green I. Plotting fluorescence as a function of temperature as the thermal cycler heats through the dissociation temperature of the product gives a DNA melting curve. The shape and position of this DNA melting curve are functions of the GC/AT ratio, length, and sequence and can be used to differentiate amplification products separated by less than 2 degrees C in melting temperature. Desired products can be distinguished from undesirable products, in many cases eliminating the need for gel electrophoresis. Analysis of melting curves can extend the dynamic range of initial template quantification when amplification is monitored with double-stranded DNA specific dyes. Complete amplification and analysis of products can be performed in less than 15 min.

Homogeneous-heterogeneous reactions in curved channel with porous medium

Science.gov (United States)

Hayat, T.; Ayub, Sadia; Alsaedi, A.

2018-06-01

Purpose of the present investigation is to examine the peristaltic flow through porous medium in a curved conduit. Problem is modeled for incompressible electrically conducting Ellis fluid. Influence of porous medium is tackled via modified Darcy's law. The considered model utilizes homogeneous-heterogeneous reactions with equal diffusivities for reactant and autocatalysis. Constitutive equations are formulated in the presence of viscous dissipation. Channel walls are compliant in nature. Governing equations are modeled and simplified under the assumptions of small Reynolds number and large wavelength. Graphical results for velocity, temperature, heat transfer coefficient and homogeneous-heterogeneous reaction parameters are examined for the emerging parameters entering into the problem. Results reveal an activation in both homogenous-heterogenous reaction effect and heat transfer rate with increasing curvature of the channel.

The J-resistance curve Leak-before-Break test program on material for the Darlington Nuclear Generating Station

International Nuclear Information System (INIS)

Mukherjee, B.

1988-01-01

The Darlington Leak-Before-Break (DLBB) approach has been developed for large diameter (21, 22, 24 inch) SA106B heat transport (HT) piping and SA105 fittings as a design alternative to pipewhip restraints and in recognition of the questionable benefits of providing such restraints. Ontario Hydro's DLBB approach is based on the elastic plastic fracture mechanics method. In this test program, J-resistance curves were determined from actual pipe heats that were used in the construction of the Darlington heat transport systems (Units 1 and 2). Test blocks were prepared using four different welding procedures for nuclear Class I piping. The test program was designed to take into account the effect of various factors such as test temperature, crack plane orientation, welding effects, etc., which have influence on fracture properties. A total of 91 tests were conducted. An acceptable lower bound J-resistance curve for the piping steels was obtained by machining maximum thickness specimens from the pipes and by testing side grooved compact tension specimens. Test results showed that all pipes, welds and heat-affected zone materials within the scope of the DLBB program exhibited uppershelf toughness behaviour. All specimens showed high crack initiation toughness Jsub(lc), rising J-resistance curve and stable and ductile crack extension. Toughness of product forms depended on the direction of crack extension (circumferential versus axial crack orientation). Toughness of DLBB welds and parent materials at 250 0 C was lower than that at 20 0 C. (author)

Susceptibility of ectomycorrhizal fungi to soil heating.

Science.gov (United States)

Kipfer, Tabea; Egli, Simon; Ghazoul, Jaboury; Moser, Barbara; Wohlgemuth, Thomas

2010-01-01

Ectomycorrhizal (EcM) fungi are an important biotic factor for successful tree recruitment because they enhance plant growth and alleviate drought stress of their hosts. Thus, EcM propagules are expected to be a key factor for forest regeneration after major disturbance events such as stand-replacing forest fires. Yet the susceptibility of soil-borne EcM fungi to heat is unclear. In this study, we investigated the heat tolerance of EcM fungi of Scots pine (Pinus sylvestris L., Pinaceae). Soil samples of three soil depths were heated to the temperature of 45, 60 and 70 °C, respectively, and surviving EcM fungi were assessed by a bioassay using Scots pine as an experimental host plant. EcM species were identified by a combination of morphotyping and sequencing of the ITS region. We found that mean number of species per sample was reduced by the 60 and 70 °C treatment, but not by the 45 °C treatment. Species composition changed due to heat. While some EcM fungi species did not survive heating, the majority of species was also found in the heated samples. The most frequent species in the heat treatment were Rhizopogon roseolus, Cenococcum geophilum and several unidentified species. Copyright © 2010 The British Mycological Society. Published by Elsevier Ltd. All rights reserved.

SU-E-T-427: Cell Surviving Fractions Derived From Tumor-Volume Variation During Radiotherapy for Non-Small Cell Lung Cancer: Comparison with Predictive Assays

Energy Technology Data Exchange (ETDEWEB)

Chvetsov, A; Schwartz, J; Mayr, N [University of Washington, Seattle, WA (United States); Yartsev, S [London Health Sciences Centre, London, Ontario (Canada)

2014-06-01

Purpose: To show that a distribution of cell surviving fractions S{sub 2} in a heterogeneous group of patients can be derived from tumor-volume variation curves during radiotherapy for non-small cell lung cancer. Methods: Our analysis was based on two data sets of tumor-volume variation curves for heterogeneous groups of 17 patients treated for nonsmall cell lung cancer with conventional dose fractionation. The data sets were obtained previously at two independent institutions by using megavoltage (MV) computed tomography (CT). Statistical distributions of cell surviving fractions S{sup 2} and cell clearance half-lives of lethally damaged cells T1/2 have been reconstructed in each patient group by using a version of the two-level cell population tumor response model and a simulated annealing algorithm. The reconstructed statistical distributions of the cell surviving fractions have been compared to the distributions measured using predictive assays in vitro. Results: Non-small cell lung cancer presents certain difficulties for modeling surviving fractions using tumor-volume variation curves because of relatively large fractional hypoxic volume, low gradient of tumor-volume response, and possible uncertainties due to breathing motion. Despite these difficulties, cell surviving fractions S{sub 2} for non-small cell lung cancer derived from tumor-volume variation measured at different institutions have similar probability density functions (PDFs) with mean values of 0.30 and 0.43 and standard deviations of 0.13 and 0.18, respectively. The PDFs for cell surviving fractions S{sup 2} reconstructed from tumor volume variation agree with the PDF measured in vitro. Comparison of the reconstructed cell surviving fractions with patient survival data shows that the patient survival time decreases as the cell surviving fraction increases. Conclusion: The data obtained in this work suggests that the cell surviving fractions S{sub 2} can be reconstructed from the tumor volume

SU-E-T-427: Cell Surviving Fractions Derived From Tumor-Volume Variation During Radiotherapy for Non-Small Cell Lung Cancer: Comparison with Predictive Assays

International Nuclear Information System (INIS)

Chvetsov, A; Schwartz, J; Mayr, N; Yartsev, S

2014-01-01

Purpose: To show that a distribution of cell surviving fractions S 2 in a heterogeneous group of patients can be derived from tumor-volume variation curves during radiotherapy for non-small cell lung cancer. Methods: Our analysis was based on two data sets of tumor-volume variation curves for heterogeneous groups of 17 patients treated for nonsmall cell lung cancer with conventional dose fractionation. The data sets were obtained previously at two independent institutions by using megavoltage (MV) computed tomography (CT). Statistical distributions of cell surviving fractions S 2 and cell clearance half-lives of lethally damaged cells T1/2 have been reconstructed in each patient group by using a version of the two-level cell population tumor response model and a simulated annealing algorithm. The reconstructed statistical distributions of the cell surviving fractions have been compared to the distributions measured using predictive assays in vitro. Results: Non-small cell lung cancer presents certain difficulties for modeling surviving fractions using tumor-volume variation curves because of relatively large fractional hypoxic volume, low gradient of tumor-volume response, and possible uncertainties due to breathing motion. Despite these difficulties, cell surviving fractions S 2 for non-small cell lung cancer derived from tumor-volume variation measured at different institutions have similar probability density functions (PDFs) with mean values of 0.30 and 0.43 and standard deviations of 0.13 and 0.18, respectively. The PDFs for cell surviving fractions S 2 reconstructed from tumor volume variation agree with the PDF measured in vitro. Comparison of the reconstructed cell surviving fractions with patient survival data shows that the patient survival time decreases as the cell surviving fraction increases. Conclusion: The data obtained in this work suggests that the cell surviving fractions S 2 can be reconstructed from the tumor volume variation curves measured

Radiosensitivity of different human tumor cells lines grown as multicellular spheroids determined from growth curves and survival data

International Nuclear Information System (INIS)

Schwachoefer, J.H.C.; Crooijmans, R.P.; van Gasteren, J.J.; Hoogenhout, J.; Jerusalem, C.R.; Kal, H.B.; Theeuwes, A.G.

1989-01-01

Five human tumor cell lines were grown as multicellular tumor spheroids (MTS) to determine whether multicellular tumor spheroids derived from different types of tumors would show tumor-type dependent differences in response to single-dose irradiation, and whether these differences paralleled clinical behavior. Multicellular tumor spheroids of two neuroblastoma, one lung adenocarcinoma, one melanoma, and a squamous cell carcinoma of the oral tongue, were studied in terms of growth delay, calculated cell survival, and spheroid control dose50 (SCD50). Growth delay and cell survival analysis for the tumor cell lines showed sensitivities that correlated well with clinical behavior of the tumor types of origin. Similar to other studies on melanoma multicellular tumor spheroids our spheroid control dose50 results for the melanoma cell line deviated from the general pattern of sensitivity. This might be due to the location of surviving cells, which prohibits proliferation of surviving cells and hence growth of melanoma multicellular tumor spheroids. This study demonstrates that radiosensitivity of human tumor cell lines can be evaluated in terms of growth delay, calculated cell survival, and spheroid control dose50 when grown as multicellular tumor spheroids. The sensitivity established from these evaluations parallels clinical behavior, thus offering a unique tool for the in vitro analysis of human tumor radiosensitivity

Thermo-Electro-Mechanical Analysis of a Curved Functionally Graded Piezoelectric Actuator with Sandwich Structure

Directory of Open Access Journals (Sweden)

Liying Jiang

2011-12-01

Full Text Available In this work, the problem of a curved functionally graded piezoelectric (FGP actuator with sandwich structure under electrical and thermal loads is investigated. The middle layer in the sandwich structure is functionally graded with the piezoelectric coefficient g31 varying continuously along the radial direction of the curved actuator. Based on the theory of linear piezoelectricity, analytical solutions are obtained by using Airy stress function to examine the effects of material gradient and heat conduction on the performance of the curved actuator. It is found that the material gradient and thermal load have significant influence on the electroelastic fields and the mechanical response of the curved FGP actuator. Without the sacrifice of actuation deflection, smaller internal stresses are generated by using the sandwich actuator with functionally graded piezoelectric layer instead of the conventional bimorph actuator. This work is very helpful for the design and application of curved piezoelectric actuators under thermal environment.

Thermo-Electro-Mechanical Analysis of a Curved Functionally Graded Piezoelectric Actuator with Sandwich Structure.

Science.gov (United States)

Yan, Zhi; Zaman, Mostafa; Jiang, Liying

2011-12-12

In this work, the problem of a curved functionally graded piezoelectric (FGP) actuator with sandwich structure under electrical and thermal loads is investigated. The middle layer in the sandwich structure is functionally graded with the piezoelectric coefficient g 31 varying continuously along the radial direction of the curved actuator. Based on the theory of linear piezoelectricity, analytical solutions are obtained by using Airy stress function to examine the effects of material gradient and heat conduction on the performance of the curved actuator. It is found that the material gradient and thermal load have significant influence on the electroelastic fields and the mechanical response of the curved FGP actuator. Without the sacrifice of actuation deflection, smaller internal stresses are generated by using the sandwich actuator with functionally graded piezoelectric layer instead of the conventional bimorph actuator. This work is very helpful for the design and application of curved piezoelectric actuators under thermal environment.

The urban heat island dynamics during heat waves: a study of cities in the United States

Science.gov (United States)

Hu, Leiqiu

2016-04-01

The urban heat island (UHI) is a common phenomenon describing that metropolitan areas are usually warmer than their rural surroundings. This effect is compounded by extreme heat events, which are a leading cause of weather-related human mortality in many countries worldwide. However, the spatial and diurnal variability of temperature and humidity in urban and adjacent rural areas during extreme heat events is not well measured and therefore not well understood. The recently developed dataset of near-surface air and dew temperature from MODIS atmospheric profiles and the new method for the UHI quantification--urban heat island curve are used to quantify the urban climatic changes during heat waves in cities of the United States. The enhanced and weakened UHIs are observed in various cities. The causes of UHI changes during heat waves are discussed, including climate region, vegetation type and amount, city geolocation, etc.

Analytical modeling of complete Nukiyama curves corresponding to expected low void fraction at high subcooling and flow rate

International Nuclear Information System (INIS)

Schroeder-Richter, D.

1996-01-01

On the basis of a new hypothesis of thermodynamic states (the superheated wall layer is not metastable but saturated at locally elevated pressure), an analytical estimation is presented of the whole boiling curve [except critical heat flux (CHF), but fixed at this point, known by experiments or correlation]. The curvature of the boiling curve (bubbly flow) is deduced from thermodynamics of irreversible processes. The wall temperature corresponding to departure from nucleate boiling is calculated from balances of momentum at the interfaces, based on the assumption that the speed of sound may be a limit for maximum evaporation mass flux and thereby heat flux, i.e., CHF. Heat flux during transition boiling is determined from balance of energy at the rewetting front. The Leidenfrost temperature, as well as wall temperature at CHF, can be calculated analytically without using empirical coefficients. Heat flux of bubbly flow and transition boiling can be matched at any empirical CHF point. All these results are determined from properties of state alone, i.e., the models can be verified for all fluids including water and liquid metals (so far at moderate heat fluxes). 52 refs., 11 figs., 2 tabs

Drought versus heat: What's the major constraint on Mediterranean green roof plants?

International Nuclear Information System (INIS)

Savi, Tadeja; Dal Borgo, Anna; Love, Veronica L.; Andri, Sergio; Tretiach, Mauro; Nardini, Andrea

2016-01-01

Green roofs are gaining momentum in the arid and semi-arid regions due to their multiple benefits as compared with conventional roofs. One of the most critical steps in green roof installation is the selection of drought and heat tolerant species that can thrive under extreme microclimate conditions. We monitored the water status, growth and survival of 11 drought-adapted shrub species grown on shallow green roof modules (10 and 13 cm deep substrate) and analyzed traits enabling plants to cope with drought (symplastic and apoplastic resistance) and heat stress (root membrane stability). The physiological traits conferring efficiency/safety to the water transport system under severe drought influenced plant water status and represent good predictors of both plant water use and growth rates over green roofs. Moreover, our data suggest that high substrate temperature represents a stress factor affecting plant survival to a larger extent than drought per se. In fact, the major cause influencing seedling survival on shallow substrates was the species-specific root resistance to heat, a single and easy measurable trait that should be integrated into the methodological framework for screening and selection of suitable shrub species for roof greening in the Mediterranean. - Highlights: • The use of hardy shrub species for roof greening should be increased. • We monitored water status of 11 shrub species growing on shallow green roofs. • Species heat and drought tolerance, growth, and survival were studied. • High substrate temperature significantly affected plant survival. • Root resistance to heat could be used as trait for species selection for green roofs.

Study on constraints for heat removal duties of the main fractionator in delayed coking units

International Nuclear Information System (INIS)

Lei, Yang; Zhang, Bingjian; Qi, Xin; Chen, Qinglin; Hui, Chi-Wai

2014-01-01

A novel method is presented in this paper to quantitatively define the heat removal of the main fractionator in delayed coking units on the basis of a fractionating precision diagram (Houghland diagram) and column grand composite curve (CGCC). By referring to the CGCC method, several envelopes are illustrated at draw trays including the top pumparound draw, diesel draw, intermediate pumparound draw and gas oil draw, the energy and material balances are then calculated. Assuming practical near-minimum thermodynamic condition (PNMTC), the minimum liquid reflux flow is zero in the envelope for pumparound trays without product draw and the minimum liquid reflux flow is defined by Houghland diagram for pumparound trays with product draw. The PNMTC-CGCC is constructed by calculating the enthalpy-flow deficit to quantitatively define the heat removal constraints in each envelope. Meanwhile, the corresponding practical heat removal curve is constructed. A case study shows that the high temperature heat removal ratio within the main fractionator increased by 8%. The proposed method offers heat removal inequality constraints for the model to optimize the heat integration between the main fractionator and the heat exchanger network. - Highlights: • A novel method defines the heat removal constraints of the main fractionator. • Fractionating precision diagram and column grand composite curve are combined. • The results are the inequality constraints in a simultaneous optimization model

Stress-induced heating in commercial conductors and its possible influence on magnet performance

International Nuclear Information System (INIS)

Easton, D.S.; Kroeger, D.M.; Moazed, A.

1976-01-01

Calorimetric measurements show that significant amounts of heat are generated when a multifilamentary composite conductor is stressed in tension to levels expected to occur in large, high-field magnet systems. When the stress on the conductor is repetitively cycled between zero and some maximum value, the amount of heat produced per cycle is constant after the first few cycles. Comparison is made between calorimetric determinations of heat injections and the work done on the specimen as indicated by stress-strain curves. Stress-strain curves for a number of commercial conductors indicate that the most important determinant of the magnitude of this effect is the choice of matrix material

The effect of price regulation on the performances of industrial symbiosis: a case study on district heating

DEFF Research Database (Denmark)

Sacchi, Romain; Ramsheva, Yana Konstantinova

2018-01-01

. The most ambitious scenario doubles the amount of excess heat supplied and reduces the heat carbon footprint by 90% compared to current level, for an end-user price increase of 41%. The price increase results from a higher supply of excess heat at a higher price and an unchanged purchase cost from the coal......This study of the district heating system of Aalborg (Denmark) analyses how fiscal instruments affect the extent excess heat recovery helps reduce the carbon footprint of heat. It builds on a supply-and-demand framework and characterizes the changes in excess heat supply with consequential life...... cycle assessment in reference to one gigajoule distributed. The heat supply curve is defined through ten scenarios, which represent incremental shares of excess heat as the constraints of the said legal instruments are lifted. The heat demand curve follows the end-users’response to price changes...

Effect of single-dose radiation on cell survival and growth hormone secretion by rat anterior pituitary cells

International Nuclear Information System (INIS)

Hochberg, Z.; Kuten, A.; Hertz, P.; Tatcher, M.; Kedar, A.; Benderly, A.

1983-01-01

Cranial irradiation has been shown to impair growth hormone secretion in children. In this study a cell culture of dispersed rat anterior pituitary cells was exposed to single doses of radiation in the range of 100 to 1500 rad. Survival curves were obtained for the different anterior pituitary cell lines, and growth hormone secretion was measured in the tissue culture medium. Both survival and growth hormone secretion curves showed an initial shoulder in the range of 0 to 300 rad, followed by a decline between 300 to 750 rad. It is concluded that growth hormone secreting acidophilic pituicytes are sensitive to radiation at single doses greater than 300 rad

A new methodology for greenhouse gas reduction in industry through improved heat exchanging and/or integration of combined heat and power

International Nuclear Information System (INIS)

Axelsson, H.; Asblad, A.; Berntsson, T.

1999-01-01

This paper presents a method that identifies economically optimal combinations of enhanced heat recovery, integration of combined heat and power (CHP), and fuel switching, in an existing industrial energy system at various emission levels. Novel types of composite curves based on pinch technology, representing the existing temperature levels for supplying heat and the possible ones that may be attained after retrofitting, are used as tools for estimating the opportunities for CHP and the trade-off between improved heat exchanging and CHP. The method is explained by an example. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Blowdown heat transfer surface in RELAP4/MOD6

International Nuclear Information System (INIS)

Nelson, R.A.; Sullivan, L.H.

1978-01-01

New heat transfer correlations for both PWR and BWR blowdowns have been implemented in the RELAP4/MOD6 program. The concept of a multidimensional surface is introduced with the heat flux from a given heat transfer correlation or correlations depicted as a mathematical surface that is dependent upon quality, wall superheat, mass flow and pressure. The heat transfer logic has been modularized to facilitate replacing boiling curves for future correlation data comparisons and investigations. To determine the validity of the blowdown surface, comparison has been performed using data from the Semiscale experimental facility. (author)

Caffeine-enhanced survival of radiation-sensitive, repair-deficient Chinese hamster cells

International Nuclear Information System (INIS)

Utsumi, H.; Elkind, M.M.

1983-01-01

A clone of V79 Chinese hamster cells (V79-AL162/S-10) with unique properties has been isolated after a challenge of parental cells (V79-AL162) with 1 mM ouabain. Compared with parental cells, or with other clones isolated after the ouabain challenge, these cells form smaller colonies, are more sensitive to both x rays and fission-spectrum neutrons, and respond atypically to a postirradiation treatment with caffeine. Their enhanced response to x rays results mainly from a large reduction in the shoulder of their survival curve, probably because in late S phase, the most resistant phase in the cell cycle, the survival curve of these cells has a reduced shoulder width. Caffeine, and to a lesser extent theophylline, added to the colony-forming medium immediately after exposure appreciably increases the width of the shoulder of these sensitive cells, whereas caffeine has the opposite effect on the response of normal V79 cells. Thus the unique response of the V79-AL162/S-10 cells to a radiation posttreatment with caffeine (increased survival) results from a net increase in their ability to repair damage that is otherwise lethal; caffeine treatment ordinarly prevents normal V79 cells from repairing damage that is only potentially lethal

Diversity Assessment of Heat Resistance of Listeria monocytogenes Strains in a Continuous-Flow Heating System

NARCIS (Netherlands)

Veen, van der S.; Wagendorp, A.; Abee, T.; Wells-Bennik, M.H.J.

2009-01-01

Listeria monocytogenes is a foodborne pathogen that has the ability to survive relatively high temperatures compared with other nonsporulating foodborne pathogens. This study was performed to determine whether L. monocytogenes strains with relatively high heat resistances are adequately inactivated

Saturated flow boiling heat transfer in water-heated vertical annulus

International Nuclear Information System (INIS)

Sun Licheng; Yan Changqi; Sun Zhonning

2005-01-01

This paper describes the saturated flow boiling heat transfer characteristics of water at 1 atm and low velocities in water-heated vertical annuli with equivalent diameters of 10 mm and 6 mm. Test section is consisted of two concentric circular tubes outer of which is made of quartz, so the whole test courses can be visualized. There are three main flow patterns of bubble flow, churn flow and churn-annular flow in the annuli, most important of which is churn flow. Flooding is the mechanism of churn flow and churn can enhance the heat transport between steam and water; Among the three factors of mass flux, inlet subcooling and annulus width, the last one has great effect on heat transport, moderately decreasing the annulus width can enhance the heat transfer; Combined annular flow model with theory of flooding and turbulent Prandtl Number, the numerical value of heat flux is given, the shape of test boiling curve and that of calculated by model is very alike, but there is large discrepancy between test data and calculated results, the most possible reason is that some parameters given by fluid flooding model are based on experimental data of common circular tubes, but not of annuli. Doing more research on flooding in annulus, particularly narrow annulus, is necessary for calculating the saturated boiling in annulus. (authors)

Dose-response curves from incomplete data

International Nuclear Information System (INIS)

Groer, P.G.

1978-01-01

Frequently many different responses occur in populations (animal or human) exposed to ionizing radiation. To obtain a dose-response curve, the exposed population is first divided into sub-groups whose members received the same radiation dose. To estimate the response, the fraction of subjects in each sub-group that showed the particular response of interest is determined. These fractions are plotted against dose to give the dose-response curve. This procedure of plotting the fractions versus the radiation dose is not the correct way to estimate the time distribution for a particular response at the different dose levels. Other observed responses competed for the individuals in the exposed population and therefore prevented manifestation of the complete information on the response-time distribution for one specific response. Such data are called incomplete in the statistical literature. A procedure is described which uses the by now classical Kaplan-Meier estimator, to establish dose-response curves from incomplete data under the assumption that the different observed responses are statistically independent. It is demonstrated that there is insufficient information in the observed survival functions to estimate the time distribution for one particular response if the assumption of independence is dropped. In addition, it is not possible to determine from the data (i.e. type of response and when it occurred) whether or not the different response-time distributions are independent. However, it is possible to give sharp bounds between which the response has to lie. This implies that for incomplete data, only a 'dose-response band' can be established if independence of the competing responses cannot be assumed. Examples are given using actual data to illustrate the estimation procedures

Experimental analysis of the power curve sensitivity test series at ROSA-III

International Nuclear Information System (INIS)

Koizumi, Y.; Iriko, M.; Yonomoto, T.; Tasaka, K.

1985-01-01

The rig of safety assessment (ROSA)-III facility is a volumetrically scaled (1/424) boiling water reactor (BWR/6) system with an electrically heated core designed for integral LOCA and ECCS tests. Seven recirculation pump suction line break LOCA experiments were conducted at the ROSA-III facility in order to examine the effect of the initial stored heat of a fuel rod on the peak cladding temperature (PCT). The break size was changed from 200% to 5% in the test series and a failure of a high pressure core spray (HPCS) diesel generator was assumed. Three power curves which represented conservative, realistic and zero initial stored heat, respectively, were used. In a large break LOCA such as 200% or 50% breaks, the initial stored heat in a fuel rod has a large effect on the cladding surface temperature because core uncovery occurs before all the initial stored heat is released, whereas in a small break LOCA such as a 5% break little effect is observed because core uncovery occurs after the initial stored heat is released. The maximum PCTs for the conservative initial stored heat case was 925 K, obtained in the 50% break experiment, and that for the realistic initial stored heat case was 835 K, obtained in the 5% break experiment. (orig./HP)

Heat-induced alterations in the cell nucleus

International Nuclear Information System (INIS)

Kampinga, H.H.

1989-01-01

Hyperthermia may kill eukaryotic cells and may also enhance the radiosensitivity of those cells that survive the heat treatment. Clinically, the possible use of hyperthermia as an adjuvant in the radiotherapeutic treatment of cancer needs the understanding of mechanisms that underlay heat-induced cell death and radiosensitization. By in vitro heating of established human (HeLaS3) and rodent (Ehrlich Ascites Tumor and LM fibroblast) cell lines, both killing and radiosensitization were investigated. (author). 1067 refs.; 76 figs.; 19 tabs

Heat-resistant, extended-spectrum β-lactamase-producing Klebsiella pneumoniae in endoscope-mediated outbreak

DEFF Research Database (Denmark)

Jørgensen, S.B.; Bojer, Martin Saxtorph; Boll, E.J.

2016-01-01

disinfection in a decontaminator designated for such use. The genetic marker clpK, which increases microbial heat resistance, has previously been described in K. pneumoniae outbreak strains. Aim To investigate the role of clpK in biofilm formation and heat-shock stability in the outbreak strain. Methods...... construction and heat-shock assays. Findings Five patients and one intubation endoscope contained K. pneumoniae with the same amplified fragment length polymorphism pattern. The outbreak strain contained the clpK genetic marker, which rendered the strain its increased heat resistance. The survival rate....... Heat resistance of certain K. pneumoniae strains may facilitate survival in biofilms on medical equipment and hence increase the potential of those strains to persist and disperse in the hospital environment....

Relaxation processes during amorphous metal alloys heating

International Nuclear Information System (INIS)

Malinochka, E.Ya.; Durachenko, A.M.; Borisov, V.T.

1982-01-01

Behaviour of Te+15 at.%Ge and Fe+13 at.%P+7 at.%C amorphous metal alloys during heating has been studied using the method of differential scanning calorimetry (DSC) as the most convenient one for determination of the value of heat effects, activation energies, temperature ranges of relaxation processes. Thermal effects corresponding to high-temperature relaxation processes taking place during amorphous metal alloys (AMA) heating are detected. The change of ratio of relaxation peaks values on DSC curves as a result of AMA heat treatment can be explained by the presence of a number of levels of inner energy in amorphous system, separated with potential barriers, the heights of which correspond to certain activation energies of relaxation processes

Optimization of heat supply systems employing nuclear power plants

International Nuclear Information System (INIS)

Urbanek, J.

1988-01-01

Decision making on the further development of heat supply systems requires optimization of the parameters. In particular, meeting the demands of peak load ranges is of importance. The heat supply coefficient α and the annual utilization of peak load equipment τ FS have been chosen as the characteristic quantities to describe them. The heat price at the consumer, C V , offers as the optimization criterion. The transport distance, temperature spread of the heating water, and different curves of annual variation of heat consumption on heat supply coefficient and heat price at the consumer. A comparison between heat supply by nuclear power plants and nuclear heating stations verifies the advantage of combined heat and power generation even with longer heat transport distances as compared with local heat supply by nuclear district heating stations based on the criterion of minimum employment of peak load boilers. (author)

Postoperative serum CEA level as predictive factor for survival in patients with colorectal cancer

International Nuclear Information System (INIS)

Lemberger, J.J.; Bogar, M.L.; Takacs Kucsera, M.F.; Csernetics, I.F.

2002-01-01

Aim: It is known that routine follow-up of patients with resected colorectal cancer includes serial CEA determinations. In this retrospective study we have investigated relationship between CEA level and survival and whether achieved results enable differentiation of tumors with slow and rapid growth. Material and Methods: Mainly between 1995 and 1999 periodic CEA determination by IRMA were performed in 269 patients after curative resection of colorectal carcinoma. Number of CEA determination/patient were 2-16(median 6). Survival ranged 4,5 and>249,7 months. Based on CEA results patients were divided in group with normal (<10ng/ml) and elevated (=10ng/ml) values regardless of postoperative treatment. Survival curves were computed by Kaplan-Meier method and difference was evaluated by logrank test and difference between proportions. Results:Normal end elevated CEA was found in 193 and 76 patients, respectively. The difference of survival curves between patients with normal and elevated CEA are highly significant (p<0,0001). However, only 10 months after tumor resection is the difference between survived proportions significant suggesting already presence of CEA produced micrometastases contributing to progression of neoplastic process. The mean survival time at normal and elevated CEA values are 142,54±17,86(median 128,60±24,04) and 34,15±4,28 (median 25,20±1,97) months, respectively. No significant difference of survival was found regarding tumor localization. Conclusion:The results show that with regard to CEA level it is possible to divide colorectal tumors on marker negative and positive. Marker negative are with slower growth and relatively good prognosis. Marker positive are associated with elevated CEA level and with considerable shorter survival. Postoperative CEA level is valuable parameter in prediction of patient's outcome

Modification of UV-induced mutation frequency and cell survival of Escherichia coli B/r WP2 trpE65 by treatment before irradiation

International Nuclear Information System (INIS)

Doudney, C.O.; Rinaldi, C.N.

1984-01-01

The UV radiation survival curve of exponentially growing cultures of Escherichia coli B/r WP2 trpE65 was modified by pretreatment for short incubation periods (up to 20 min) with chloramphenicol such that an extended exponential section of intermediate slope appeared between the shoulder and the final exponential slope. Surges of mutation to tryptophan independence occurred with each increase in slope of the survival curve. These surges were separated by extended sections of little mutation. Nalidixic acid prevented both the changes in survival and mutation. Mutation curves obtained with overnight cultures had three extended sections of little mutation alternating with section of high mutation. Reincubation for 60 min in fresh medium reduced or eliminated the low-response sections. These reappeared after 80 to 90 min, when DNA had doubled in the culture and before the initial synchronous cell divisions had occurred. Nalidixic acid prevented this reappearance

High heat flux x-ray monochromators: What are the limits?

International Nuclear Information System (INIS)

Rogers, C.S.

1997-06-01

First optical elements at third-generation, hard x-ray synchrotrons, such as the Advanced Photon Source (APS), are subjected to immense heat fluxes. The optical elements include crystal monochromators, multilayers and mirrors. This paper presents a mathematical model of the thermal strain of a three-layer (faceplate, heat exchanger, and baseplate), cylindrical optic subjected to narrow beam of uniform heat flux. This model is used to calculate the strain gradient of a liquid-gallium-cooled x-ray monochromator previously tested on an undulator at the Cornell High Energy Synchrotron Source (CHESS). The resulting thermally broadened rocking curves are calculated and compared to experimental data. The calculated rocking curve widths agree to within a few percent of the measured values over the entire current range tested (0 to 60 mA). The thermal strain gradient under the beam footprint varies linearly with the heat flux and the ratio of the thermal expansion coefficient to the thermal conductivity. The strain gradient is insensitive to the heat exchanger properties and the optic geometry. This formulation provides direct insight into the governing parameters, greatly reduces the analysis time, and provides a measure of the ultimate performance of a given monochromator

Application of the risk-informed methodology for APR1400 P-T limits curve

Energy Technology Data Exchange (ETDEWEB)

Kim, K.; Namgung, I. [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2014-07-01

A reactor pressure vessel (RPV) in a nuclear power plant has operational limits of pressure and temperature to prevent a potential drastic propagation of cracks due to brittle fracture. We call it a pressure-temperature limits curve (P-T limits curve). Appendix G of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section XI, provides deterministic procedures to develop the P-T limits curve for the reactor pressure vessel. Recently, an alternative risk-informed methodology has been added in the ASME Code. Risk-informed means that we can consider insights from a probabilistic risk assessment by using this methodology. This alternative methodology provides a simple procedure to develop risk-informed P-T limits for heat up, cool down, and hydrostatic test events. The risk-informed P-T limits curve is known to provide more operational flexibility, particularly for reactor pressure vessels with relatively high irradiation levels and radiation sensitive materials. In this paper, we developed both the deterministic and a risk-informed P-T limits curve for an APR1400 reactor using Appendix G of the ASME Code, Section XI and compare the results in terms of additional operational margin. (author)

Anomalies and other concerns related to the critical heat flux

International Nuclear Information System (INIS)

Groeneveld, D.C.

2009-01-01

This paper summarizes various unusual trends in the critical heat flux (CHF) that have been observed experimentally in tubes. They include the following: Occurrence of a minimum in the CHF vs. quality (X) curve at high flows - leading to an initial upstream CHF occurrence in uniformly heated tubes. This phenomenon has been observed at high flows in both water and Freon. Occurrence of a limiting quality region on the CHF vs. X curve where the CHF drops by 30 - 90% for a nearly constant quality. This is thought to correspond to the boundary between the entrainment-controlled and the deposition-controlled region and causes problems for prediction methods of the form CHF=f(X). Impact of flow obstructions on the occurrence of upstream CHF and the limiting quality region. The additional mixing by grid spacers or bundle appendages results in a more homogeneous phase distribution, thus diminishing the effects of flow regime/heat transfer regime transitions responsible for the above unusual CHF trends. This will lead to a more gradually decreasing CHF vs. X curve. Absence of a CHF temperature excursion at high flows and high qualities - this is found to be caused by a change in slope of the transition boiling part of the boiling curve from a negative value (usual trend that results in a dryout temperature excursion) to a positive slope. Gradual disappearance of the sharp temperature excursion at CHF when increasing the pressure towards and beyond the critical pressure - no drastic change is observed in the shape of the axial temperature distribution of a heated tube experiencing CHF or heat transfer deterioration, when, for constant mass flux and inlet temperature, the pressure is gradually increased from subcritical to supercritical. CHF fluid-to-fluid modeling: differences in CHF behavior at certain conditions between refrigerants and water at equivalent conditions. The mechanisms responsible for these trends and the implications for predicting CHF for bundle geometries

Thermoluminescence study of X-ray irradiated muscovite mineral under various heating rate

International Nuclear Information System (INIS)

Kalita, J.M.; Wary, G.

2014-01-01

The thermoluminescence (TL) glow curves of X-ray irradiated micro-grain natural muscovite were recorded within 298–520 K at various linear heating rates (2 K/s, 4 K/s, 6 K/s, 8 K/s and 10 K/s). Natural TL of muscovite was checked, but no significant TL was observed within 298–520 K in any heating rate. Within the heating rate 2–10 K/s only a low temperature distinct peak was observed in the temperature range 348–357 K. The TL parameters such as activation energy, order of kinetic, geometrical symmetry factor and pre-exponential frequency factor were investigated from the glow peak by Peak Shape (PS) method and Computerized Glow Curve Deconvolution (CGCD) technique. At lowest heating rate the glow peak obeys non-first order kinetic and at the highest heating rate it follows the second order kinetic. The variation of peak integrals, peak maximum temperatures, FWHM and activation energy with heating rates were investigated, and the glow curves at higher rates were found to be influenced by the presence of the thermal quenching. The thermal quenching activation energy and pre-exponential factor were calculated and found to be 2.31±0.02 eV and 3.46×10 14 s −1 , respectively. -- Highlights: • Muscovite is a silicate mineral with chemical formula KAl 2 (Si 3 Al)O 10 (OH,F) 2 . • TL of natural and X-ray induced muscovite was studied under various heating rates. • TL parameters were evaluated by Peak Shape and CGCD method. • Thermal quenching parameters (W and C) of muscovite were evaluated

Radiobiological effects of tritiated water short-term exposure on V79 clonogenic cell survival

DEFF Research Database (Denmark)

Siragusa, Mattia; Fredericia, Nina Pil Møntegaard; Jensen, Mikael

2018-01-01

We set out to improve the accuracy of absorbed dose calculations for in-vitro measurements of the Relative Biological Effectiveness (RBE) of tritiated water (HTO) for the clonogenic cell survival assay, also considering the influence of the end-of-track Linear Energy Transfer (LET) of low-energy...... in suspension are usually comparable to those for adherent cells. RBEs calculated at the 10% survival fraction through the use of the average energy are almost similar to those obtained with the beta-spectrum. For adherent cells, an RBE of 1.6 was found when HTO cell survival curves were compared to acute γ...

Selection of heat transfer model for describing short-pulse laser heating silica-based sensor

International Nuclear Information System (INIS)

Hao Xiangnan; Nie Jinsong; Li Hua; Bian Jintian

2012-01-01

The fundamental equations of Fourier heat transfer model and non-Fourier heat transfer model were numerically solved, with the finite difference method. The relative changes between temperature curves of the two heat transfer models were analyzed under laser irradiation with different pulse widths of 10 ns, 1 ns, 100 ps, 10 ps. The impact of different thermal relaxation time on non-Fourier model results was discussed. For pulses of pulse width less than or equal to 100 ps irradiating silicon material, the surface temperature increases slowly and carrier effect happens, which the non-Fourier model can reflect properly. As for general material, when the pulse width is less than or equal to the thermal relaxation time of material, carrier effect occurs. In this case, the non-Fourier model should be used. (authors)

Developmental acclimation to low or high humidity conditions affect starvation and heat resistance of Drosophila melanogaster.

Science.gov (United States)

Parkash, Ravi; Ranga, Poonam; Aggarwal, Dau Dayal

2014-09-01

Several Drosophila species originating from tropical humid localities are more resistant to starvation and heat stress than populations from high latitudes but mechanistic bases of such physiological changes are largely unknown. In order to test whether humidity levels affect starvation and heat resistance, we investigated developmental acclimation effects of low to high humidity conditions on the storage and utilization of energy resources, body mass, starvation survival, heat knockdown and heat survival of D. melanogaster. Isofemale lines reared under higher humidity (85% RH) stored significantly higher level of lipids and showed greater starvation survival hours but smaller in body size. In contrast, lines reared at low humidity evidenced reduced levels of body lipids and starvation resistance. Starvation resistance and lipid storage level were higher in females than males. However, the rate of utilization of lipids under starvation stress was lower for lines reared under higher humidity. Adult flies of lines reared at 65% RH and acclimated under high or low humidity condition for 200 hours also showed changes in resistance to starvation and heat but such effects were significantly lower as compared with developmental acclimation. Isofemale lines reared under higher humidity showed greater heat knockdown time and heat-shock survival. These laboratory observations on developmental and adult acclimation effects of low versus high humidity conditions have helped in explaining seasonal changes in resistance to starvation and heat of the wild-caught flies of D. melanogaster. Thus, we may suggest that wet versus drier conditions significantly affect starvation and heat resistance of D. melanogaster. Copyright © 2014 Elsevier Inc. All rights reserved.

The effect of the freezing curve type on bull spermatozoa motility after thawing

Directory of Open Access Journals (Sweden)

Martina Doležalová

2015-01-01

Full Text Available The objective of this work was to determine the effect of selected freezing curves on spermatozoa survivability after thawing, defined by its motility. The ejaculates of nine selected sires of the same age, breed, and frequency of collecting, bred under the same breeding conditions including handling, stabling, feeding system and feeding ratio composition, were repeatedly collected and evaluated. Sperm samples of each sire were diluted using only one extender and divided into four parts. Selected four freezing curves – the standard, commercially recommended three-phase curve; a two-phase curve; a slow three-phase curve; and a fast three-phase curve, differing in the course of temperature vs time, were applied. The percentage rate of progressive motile spermatozoa above head was determined immediately after thawing, and after 30, 60, 90, and 120 min of the thermodynamic test (TDT. Moreover, average spermatozoa motility (AMOT and spermatozoa motility decrease (MODE throughout the entire TDT were evaluated. Insemination doses frozen using the simpler two-phase curve demonstrated the highest motility values (+2.97% to +10.37%; P < 0.05–0.01 immediately after thawing and during the entire TDT. Concurrently, the highest AMOT (+4.37% to +8.82%; P < 0.01 was determined. The highest spermatozoa motility values were detected after thawing doses frozen by the two-phase freezing curve in eight out of nine sires. Simultaneously, a significant effect of sire individuality was clearly confirmed. Inter-sire differences of spermatozoa motility during TDT as well as AMOT and MODE were significant (P < 0.01. The findings describing both factors of interaction indicate the necessity of individual cryopreservation of the ejaculate to increase its fertilization capability after thawing.

Advanced Online Survival Analysis Tool for Predictive Modelling in Clinical Data Science.

Science.gov (United States)

Montes-Torres, Julio; Subirats, José Luis; Ribelles, Nuria; Urda, Daniel; Franco, Leonardo; Alba, Emilio; Jerez, José Manuel

2016-01-01

One of the prevailing applications of machine learning is the use of predictive modelling in clinical survival analysis. In this work, we present our view of the current situation of computer tools for survival analysis, stressing the need of transferring the latest results in the field of machine learning to biomedical researchers. We propose a web based software for survival analysis called OSA (Online Survival Analysis), which has been developed as an open access and user friendly option to obtain discrete time, predictive survival models at individual level using machine learning techniques, and to perform standard survival analysis. OSA employs an Artificial Neural Network (ANN) based method to produce the predictive survival models. Additionally, the software can easily generate survival and hazard curves with multiple options to personalise the plots, obtain contingency tables from the uploaded data to perform different tests, and fit a Cox regression model from a number of predictor variables. In the Materials and Methods section, we depict the general architecture of the application and introduce the mathematical background of each of the implemented methods. The study concludes with examples of use showing the results obtained with public datasets.

Effects of hyperthermia and radiation on mouse testis stem cells

International Nuclear Information System (INIS)

Reid, B.O.; Mason, K.A.; Withers, H.R.; West, J.

1981-01-01

The response of mouse testis stem cells to hyperthermia and combined hyperthermia-radiation treatments was assayed by spermatogenic colony regrowth, sperm head counts, testis weight loss, and fertility. With the use of spermatogenic colony assay, thermal enhancement ratios at an isosurvival level of 0.1 were 1.27 at 41 degrees, 1.80 at 42 degrees, and 3.97 at 43 degrees for testes exposed to heat for 30 min prior to irradiation. Sperm head counts were reduced by heat alone from a surviving fraction of 0.58 at 41 degrees to 0.003 at 42.5-43.5 degrees. Curves for sperm head survival measured 56 days after the testes had been heated for 30 min prior to irradiation were biphasic and showed a progressive downward displacement to lower survival with increasing temperature. The 41, 42, and 43 degrees curves were displaced downward by factors of 2, 58, and 175, respectively. The proportion of animals remaining sterile after 30 min of heat (41-43 degrees) and the median sterility period in days increased with increasing temperature. The minimum sperm count necessary to regain fertility was 13% of the normal mouse level

Heating and dynamics of two flare loop systems observed by AIA and EIS

Energy Technology Data Exchange (ETDEWEB)

Li, Y.; Ding, M. D. [School of Astronomy and Space Science, Nanjing University, Nanjing 210093 (China); Qiu, J., E-mail: yingli@nju.edu.cn [Department of Physics, Montana State University, Bozeman, MT 59717 (United States)

2014-02-01

We investigate heating and evolution of flare loops in a C4.7 two-ribbon flare on 2011 February 13. From Solar Dynamics Observatory/Atmospheric Imaging Assembly (AIA) imaging observations, we can identify two sets of loops. Hinode/EUV Imaging Spectrometer (EIS) spectroscopic observations reveal blueshifts at the feet of both sets of loops. The evolution and dynamics of the two sets are quite different. The first set of loops exhibits blueshifts for about 25 minutes followed by redshifts, while the second set shows stronger blueshifts, which are maintained for about one hour. The UV 1600 observation by AIA also shows that the feet of the second set of loops brighten twice. These suggest that continuous heating may be present in the second set of loops. We use spatially resolved UV light curves to infer heating rates in the few tens of individual loops comprising the two loop systems. With these heating rates, we then compute plasma evolution in these loops with the 'enthalpy-based thermal evolution of loops' model. The results show that, for the first set of loops, the synthetic EUV light curves from the model compare favorably with the observed light curves in six AIA channels and eight EIS spectral lines, and the computed mean enthalpy flow velocities also agree with the Doppler shift measurements by EIS. For the second set of loops modeled with twice-heating, there are some discrepancies between modeled and observed EUV light curves in low-temperature bands, and the model does not fully produce the prolonged blueshift signatures as observed. We discuss possible causes for the discrepancies.

Aspects of quantum field theory in curved space-time

International Nuclear Information System (INIS)

Fulling, S.A.

1989-01-01

The theory of quantum fields on curved spacetimes has attracted great attention since the discovery, by Stephen Hawking, of black-hole evaporation. It remains an important subject for the understanding of such contemporary topics as inflationary cosmology, quantum gravity and superstring theory. The topics covered include normal-mode expansions for a general elliptic operator, Fock space, the Casimir effect, the Klein 'paradox', particle definition and particle creation in expanding universes, asymptotic expansion of Green's functions and heat kernels, and renormalization of the stress tensor. (author)

Ability to Discriminate Between Sustainable and Unsustainable Heat Stress Exposures-Part 2: Physiological Indicators.

Science.gov (United States)

Garzón-Villalba, Ximena P; Wu, Yougui; Ashley, Candi D; Bernard, Thomas E

2017-07-01

There are times when it is not practical to assess heat stress using environmental metrics and metabolic rate, and heat strain may provide an alternative approach. Heat strain indicators have been used for decades as tools for monitoring physiological responses to work in hot environments. Common indicators of heat strain are body core temperature (assessed here as rectal temperature Tre), heart rate (HR), and average skin temperature (Tsk). Data collected from progressive heat stress trials were used to (1) demonstrate if physiological heat strain indicators (PHSIs) at the upper limit of Sustainable heat stress were below generally accepted limits; (2) suggest values for PHSIs that demonstrate a Sustainable level of heat stress; (3) suggest alternative PHSIs; and (4) determine if metabolic rate was an effect modifier. Two previous progressive heat stress studies included 176 trials with 352 pairs of Sustainable and Unsustainable exposures over a range of relative humidities and metabolic rates using 29 participants. To assess the discrimination ability of PHSIs, conditional logistic regression and stepwise logistic regression were used to find the best combinations of predictors of Unsustainable exposures. The accuracy of the models was assessed using receiver operating characteristic curves. Current recommendations for physiological heat strain limits were associated with probabilities of Unsustainable greater than 0.5. Screening limits for Sustainable heat stress were Tre of 37.5°C, HR of 105 bpm, and Tsk of 35.8°C. Tsk alone resulted in an area under the curve of 0.85 and the combination of Tsk and HR (area under the curve = 0.88) performed the best. The adjustment for metabolic rate was statistically significant for physiological strain index or ∆Tre-sk as main predictors, but its effect modification was negligible and could be ignored. Based on the receiver operating characteristic curve, PHSIs (Tre, HR, and Tsk) can accurately predict Unsustainable heat

Effects of glutamine pretreatment on learning and memory in heat-exposed rats

Institute of Scientific and Technical Information of China (English)

Shenghao Zhao; Lei Wang; Qin Wang; Siyi Wang; Chundi Deng; Xianfei Xie; Youe Yan; Hui Wang

2008-01-01

BACKGROUND: Glutamine (Gln) pretreatment can protect neural cells from injuries due to heat, ischemia, hypoxia, endotoxemia, and inflammatory factors.OBJECTIVE: To observe the effects of Gln pretreatment on learning and memory, survival time, and rectal temperature in heat-exposed rats.DESIGN, TIME AND SETTING: The present randomized grouping, neurobehavioral experiment was performed at the Laboratory of Department of Pharmacology, Basic School of Medicine, Wuhan University between March and September 2007.MATERIALS: Twenty-four healthy, Wistar rats were included in this study. SPX-160B biochemistry incubator (Shanghai Experimental Equipment Co., Ltd., China), probe electronic thermometer (11000 type, Maikepai Science and Technology Co., Ltd., China), Y-type maze box used in conjunction with MG-2 maze stimulator (Zhangjiagang Biomedical Instrument Factory, China), L-Gin (Batch No. 061218, 5 g/bottle, prepared into 10% aqueous solution, Amresco Company, USA) were used.METHODS: Twenty-four rats were randomly and evenly divided into 3 groups: heat-exposed, Gln low-lose, and Gln high-dose. Following learning and memory testing with the Y-maze, rats in the heat-exposed group were subjected to heat injury (40.5-41.5℃) in a biochemistry incubator. Rectal temperature was measured every 5 minutes. Thirty-five minutes after heat exposure, rats were removed and placed in the Y-type maze to test learning and memory again. Subsequently, the rats were returned to the same environment of thermal stimulation until they died. Rat survival time was recorded. Subsequent to learning and memory testing, rats in the Gln low-dose and high-dose groups received an i.p. injection of Gln (0.4 g/kg and 0.8 g/kg, respectively), and were exposed to heat injury. The remaining experimental procedures remained the same as for the heat-exposed group.MAIN OUTCOME MEASURES: Rat learning and memory, rectal temperature, and survival time in heat exposure environment.RESULTS: (1) In the Y

Optimum performance analysis of an irreversible Diesel heat engine affected by variable heat capacities of working fluid

International Nuclear Information System (INIS)

Zhao, Yingru; Chen, Jincan

2007-01-01

An irreversible cycle model of the Diesel heat engine is established in which the temperature dependent heat capacities of the working fluid, the irreversibilities resulting from non-isentropic compression and expansion processes and heat leak losses through the cylinder wall are taken into account. The adiabatic equation of ideal gases with temperature dependent heat capacity is strictly deduced without using the additional approximation condition in the relevant literature and is used to analyze the performance of the Diesel heat engine. Expressions for the work output and efficiency of the cycle are derived by introducing the pressure ratio and the compression and expansion efficiencies. The performance characteristic curves of the Diesel heat engine are presented for a set of given parameters. The optimum criteria of some important parameters such as the work output, efficiency, pressure ratio and temperatures of the working fluid are obtained. Moreover, the influence of the compression and expansion efficiencies, variable heat capacities, heat leak and other parameters on the performance of the cycle is discussed in detail. The results obtained may provide a theoretical basis for both optimal design and operation of real Diesel heat engines

Thermoluminescence under an exponential heating function: I. Theory

International Nuclear Information System (INIS)

Kitis, G; Chen, R; Pagonis, V; Carinou, E; Kamenopoulou, V

2006-01-01

Constant temperature hot gas readers are widely employed in thermoluminescence dosimetry. In such readers the sample is heated according to an exponential heating function. The single glow-peak shape derived under this heating condition is not described by the TL kinetics equation corresponding to a linear heating rate. In the present work TL kinetics expressions, for first and general order kinetics, describing single glow-peak shapes under an exponential heating function are derived. All expressions were modified from their original form of I(n 0 , E, s, b, T) into I(I m , E, T m , b, T) in order to become more efficient for glow-curve deconvolution analysis. The efficiency of all algorithms was extensively tested using synthetic glow-peaks

Survival pathological prognosis factors in breast cancer

International Nuclear Information System (INIS)

Gonzalez-Longoria Boada, Lourdes B.

2012-01-01

A descriptive and longitudinal study of 273 women with breast cancer belonging to Granma province was carried out from 2003 to 2004, in order to analyze the survival of this female population, reason why the method of Kaplan Meier was used for the calculation of the mentioned variable and the Log Rank test was used for the comparison of curves. Patients with higher survival at 5 years were those who had tumors of 2 cm or less (87.5%), histological grade I (90.3%), nuclear grade I (88.3%), as well as the absence of vascular, lymphatic or lymph node invasion (with 80.6; 74.9 and 6.1% respectively). Also, tumor size, histological and nuclear grade, nodal status, as well as lymphatic and vascular invasion constituted prognosis factors, which favored the individualization of therapeutic behaviors

Drought versus heat: What's the major constraint on Mediterranean green roof plants?

Energy Technology Data Exchange (ETDEWEB)

Savi, Tadeja, E-mail: tsavi@units.it [Dipartimento di Scienze della Vita, Università di Trieste, Via L. Giorgieri 10, 34127 Trieste (Italy); Dal Borgo, Anna, E-mail: dalborgo.anna@gmail.com [Dipartimento di Scienze della Vita, Università di Trieste, Via L. Giorgieri 10, 34127 Trieste (Italy); Love, Veronica L., E-mail: vllove1@sheffield.ac.uk [Dipartimento di Scienze della Vita, Università di Trieste, Via L. Giorgieri 10, 34127 Trieste (Italy); Department of Landscape, University of Sheffield, Western Bank, Sheffield, South Yorkshire S10 2TN (United Kingdom); Andri, Sergio, E-mail: s.andri@seic.it [Harpo seic verdepensile, Via Torino 34, 34123 Trieste (Italy); Tretiach, Mauro, E-mail: tretiach@units.it [Dipartimento di Scienze della Vita, Università di Trieste, Via L. Giorgieri 10, 34127 Trieste (Italy); Nardini, Andrea, E-mail: nardini@units.it [Dipartimento di Scienze della Vita, Università di Trieste, Via L. Giorgieri 10, 34127 Trieste (Italy)

2016-10-01

Green roofs are gaining momentum in the arid and semi-arid regions due to their multiple benefits as compared with conventional roofs. One of the most critical steps in green roof installation is the selection of drought and heat tolerant species that can thrive under extreme microclimate conditions. We monitored the water status, growth and survival of 11 drought-adapted shrub species grown on shallow green roof modules (10 and 13 cm deep substrate) and analyzed traits enabling plants to cope with drought (symplastic and apoplastic resistance) and heat stress (root membrane stability). The physiological traits conferring efficiency/safety to the water transport system under severe drought influenced plant water status and represent good predictors of both plant water use and growth rates over green roofs. Moreover, our data suggest that high substrate temperature represents a stress factor affecting plant survival to a larger extent than drought per se. In fact, the major cause influencing seedling survival on shallow substrates was the species-specific root resistance to heat, a single and easy measurable trait that should be integrated into the methodological framework for screening and selection of suitable shrub species for roof greening in the Mediterranean. - Highlights: • The use of hardy shrub species for roof greening should be increased. • We monitored water status of 11 shrub species growing on shallow green roofs. • Species heat and drought tolerance, growth, and survival were studied. • High substrate temperature significantly affected plant survival. • Root resistance to heat could be used as trait for species selection for green roofs.

Survival strategies in arctic ungulates

Directory of Open Access Journals (Sweden)

N. J. C. Tyler

1990-09-01

Full Text Available Arctic ungulates usually neither freeze nor starve to death despite the rigours of winter. Physiological adaptations enable them to survive and reproduce despite long periods of intense cold and potential undernutrition. Heat conservation is achieved by excellent insulation combined with nasal heat exchange. Seasonal variation in fasting metabolic rate has been reported in several temperate and sub-arctic species of ungulates and seems to occur in muskoxen. Surprisingly, there is no evidence for this in reindeer. Both reindeer and caribou normally maintain low levels of locomotor activity in winter. Light foot loads are important for reducing energy expenditure while walking over snow. The significance and control of selective cooling of the brain during hard exercise (e.g. escape from predators is discussed. Like other cervids, reindeer and caribou display a pronounced seasonal cycle of appetite and growth which seems to have an intrinsic basis. This has two consequences. First, the animals evidently survive perfectly well despite enduring negative energy balance for long periods. Second, loss of weight in winter is not necessarily evidence of undernutrition. The main role of fat reserves, especially in males, may be to enhance reproductive success. The principal role of fat reserves in winter appears to be to provide a supplement to, rather than a substitute for, poor quality winter forage. Fat also provides an insurance against death during periods of acute starvation.

On the analysis of clonogenic survival data: Statistical alternatives to the linear-quadratic model

International Nuclear Information System (INIS)

Unkel, Steffen; Belka, Claus; Lauber, Kirsten

2016-01-01

The most frequently used method to quantitatively describe the response to ionizing irradiation in terms of clonogenic survival is the linear-quadratic (LQ) model. In the LQ model, the logarithm of the surviving fraction is regressed linearly on the radiation dose by means of a second-degree polynomial. The ratio of the estimated parameters for the linear and quadratic term, respectively, represents the dose at which both terms have the same weight in the abrogation of clonogenic survival. This ratio is known as the α/β ratio. However, there are plausible scenarios in which the α/β ratio fails to sufficiently reflect differences between dose-response curves, for example when curves with similar α/β ratio but different overall steepness are being compared. In such situations, the interpretation of the LQ model is severely limited. Colony formation assays were performed in order to measure the clonogenic survival of nine human pancreatic cancer cell lines and immortalized human pancreatic ductal epithelial cells upon irradiation at 0-10 Gy. The resulting dataset was subjected to LQ regression and non-linear log-logistic regression. Dimensionality reduction of the data was performed by cluster analysis and principal component analysis. Both the LQ model and the non-linear log-logistic regression model resulted in accurate approximations of the observed dose-response relationships in the dataset of clonogenic survival. However, in contrast to the LQ model the non-linear regression model allowed the discrimination of curves with different overall steepness but similar α/β ratio and revealed an improved goodness-of-fit. Additionally, the estimated parameters in the non-linear model exhibit a more direct interpretation than the α/β ratio. Dimensionality reduction of clonogenic survival data by means of cluster analysis was shown to be a useful tool for classifying radioresistant and sensitive cell lines. More quantitatively, principal component analysis allowed

Heat transfer for plasma facing components

International Nuclear Information System (INIS)

Boyd, R.D.; Meng, X.; Maughan, H.

1995-01-01

Although the high heat flux requirements for plasma-facing components have been reduced drastically from 40.0 MW/m 2 to near 10.0 MW/m 2 , there are still some refinements needed. This paper highlights: (1) recent accomplishments and pinpoints new thermal solutions and problem areas of immediate concern to the development of plasma-facing components, and (2) next generation thermal hydraulic problems which must be addressed to insure safety and reliability in component operation. More specifically the near-term thermal hydraulic problems entail: (1) generating an appropriate data base to insure the development of single-side heat flux correlations; and (2) adapting the existing vast uniform heat flux literature to the case of non-uniform heat flux distributions found in plasma facing components in fusion reactors. Results are presented for the latter task which includes: (a) an accurate subcooled flow boiling curve correlation for the partial nucleate boiling regime which can be adapted using previously proposed correlations relating single-side boundary heat flux to heat transfer, in uniformly heated channels, (b) the evaluation of the possibility of using the existing literature directly with redefined parameters, and (c) an estimation of circumferential variations in the heat transfer coefficient

The pretective effects of heat shock protein 70 on radiation injury of V79 cells

International Nuclear Information System (INIS)

Qin Yongchun; Zhang Baoguo; Hong Chengjiao

2008-01-01

Westem blot was used to detect the expression of heat shock protein 70 in V79 cells after heat shock pretreatment; V79 cells were irradiated using γ-ray after heat shock pretreatment, survival rate was observed using Colony formation assay. Our study shows that 1) the overexpression of heat shock protein 70 was observed in cells recovering for 1 hour after heat shock pretreatment, with peak expression in cells recovering for 4 hours, and could last for 24 hours; 2) heat shock pretreatment was able to elevate survival rate of V79 cells after irradiation by 60 Co γ ray (when the irradiation dose was less than 6 Gy). The results indicate that heat shock protein 70 has protective effect on radiation induced cell death of V79 cells (when the irradiation dose was less than 6 Gy). (authors)

Heat stress reduction of helicopter crew wearing a ventilated vest

NARCIS (Netherlands)

Reffeltrath, P.A.

2006-01-01

Background: Helicopter pilots are often exposed to periods of high heat strain, especially when wearing survival suits. Therefore, a prototype of a ventilated vest was evaluated on its capability to reduce the heat strain of helicopter pilots during a 2-h simulated flight. Hypothesis: It was

Valosin-containing protein VCP/p97 is essential for the intracellular development of Leishmania and its survival under heat stress.

Science.gov (United States)

Aguiar, Bruno G; Padmanabhan, Prasad K; Dumas, Carole; Papadopoulou, Barbara

2018-06-12

VCP/p97/Cdc48 is one of the best-characterized type II cytosolic AAA+ ATPases most known for their role in ubiquitin-dependent protein quality control. Here, we provide functional insights into the role of the Leishmania VCP/p97 homolog (LiVCP) in the parasite intracellular development. We demonstrate that although LiVCP is an essential gene, L. infantum promastigotes can grow with less VCP. In contrast, growth of axenic and intracellular amastigotes is dramatically affected upon decreased LiVCP levels in heterozygous and temperature sensitive LiVCP mutants or the expression of dominant negative mutants known to specifically target the second conserved VCP ATPase domain, a major contributor of the VCP overall ATPase activity. Interestingly, these VCP mutants are also unable to survive heat stress and a temperature sensitive VCP mutant is defective in amastigote growth. Consistent with LiVCP's essential function in amastigotes, LiVCP mRNA undergoes 3'UTR-mediated developmental regulation, resulting in higher VCP expression in amastigotes. Furthermore, we show that parasite mutant lines expressing lower VCP levels or dominant negative VCP forms exhibit high accumulation of polyubiquitinated proteins and increased sensitivity to proteotoxic stress, supporting the ubiquitin-selective chaperone function of LiVCP. Together, these results emphasize the crucial role LiVCP plays under heat stress and during the parasite intracellular development. This article is protected by copyright. All rights reserved.

Aspherical Supernovae: Effects on Early Light Curves

Science.gov (United States)

Afsariardchi, Niloufar; Matzner, Christopher D.

2018-04-01

Early light from core-collapse supernovae, now detectable in high-cadence surveys, holds clues to a star and its environment just before it explodes. However, effects that alter the early light have not been fully explored. We highlight the possibility of nonradial flows at the time of shock breakout. These develop in sufficiently nonspherical explosions if the progenitor is not too diffuse. When they do develop, nonradial flows limit ejecta speeds and cause ejecta–ejecta collisions. We explore these phenomena and their observational implications using global, axisymmetric, nonrelativistic FLASH simulations of simplified polytropic progenitors, which we scale to representative stars. We develop a method to track photon production within the ejecta, enabling us to estimate band-dependent light curves from adiabatic simulations. Immediate breakout emission becomes hidden as an oblique flow develops. Nonspherical effects lead the shock-heated ejecta to release a more constant luminosity at a higher, evolving color temperature at early times, effectively mixing breakout light with the early light curve. Collisions between nonradial ejecta thermalize a small fraction of the explosion energy; we will address emission from these collisions in a subsequent paper.

Improved survival in HIV treatment programs in Asia

Science.gov (United States)

De La Mata, Nicole L; Kumarasamy, Nagalingeswaran; Khol, Vohith; Ng, Oon Tek; Van Nguyen, Kinh; Merati, Tuti Parwati; Pham, Thuy Thanh; Lee, Man Po; Durier, Nicolas; Law, Matthew

2016-01-01

Background Antiretroviral treatment (ART) for HIV-positive patients has expanded rapidly in Asia over the last ten years. Our study aimed to describe the time trends and risk factors for overall survival in patients receiving first-line ART in Asia. Methods We included HIV-positive adult patients who initiated ART between 2003–2013 (n=16 546), from seven sites across six Asia-Pacific countries. Patient follow-up was to May 2014. We compared survival for each country and overall by time period of ART initiation using Kaplan-Meier curves. Factors associated with mortality were assessed using Cox regression, stratified by site. We also summarized first-line ART regimens, CD4 count at ART initiation, and CD4 and HIV viral load testing frequencies. Results There were 880 deaths observed over 54 532 person-years of follow-up, a crude rate of 1.61 (1.51, 1.72) per 100 person-years. Survival significantly improved in more recent years of ART initiation. The survival probabilities at 4 years follow-up for those initiating ART in 2003–05 was 92.1%, 2006–09 was 94.3% and 2010–2013 was 94.5% (pAsia have improved survival in more recent years of ART initiation. This is likely a consequence of improvements in treatment and, patient management and monitoring over time. PMID:26961354

Aspects of quantum field theory in curved space-time

Energy Technology Data Exchange (ETDEWEB)

Fulling, S.A. (Texas A and M Univ., College Station, TX (USA). Dept. of Mathematics)

1989-01-01

The theory of quantum fields on curved spacetimes has attracted great attention since the discovery, by Stephen Hawking, of black-hole evaporation. It remains an important subject for the understanding of such contemporary topics as inflationary cosmology, quantum gravity and superstring theory. The topics covered include normal-mode expansions for a general elliptic operator, Fock space, the Casimir effect, the Klein 'paradox', particle definition and particle creation in expanding universes, asymptotic expansion of Green's functions and heat kernels, and renormalization of the stress tensor. (author).

Heat pipe applications for future Air Force spacecraft

International Nuclear Information System (INIS)

Mahefkey, T.; Barthelemy, R.R.

1980-01-01

This paper summarizes the envisioned, future usage of high and low temperature heat pipes in advanced Air Force spacecraft. Thermal control requirements for a variety of communications, surveillance, and space defense missions are forecast. Thermal design constraints implied by survivability to potential weapons effects are outlined. Applications of heat pipes to meet potential low and high power spacecraft mission requirements and envisioned design constraints are suggested. A brief summary of past Air Force sponsored heat pipe development efforts is presented and directions for future development outlined, including those applicable to advanced photovoltaic and nuclear power subsystem applications of heat pipes

Stenting for curved lesions using a novel curved balloon: Preliminary experimental study.

Science.gov (United States)

Tomita, Hideshi; Higaki, Takashi; Kobayashi, Toshiki; Fujii, Takanari; Fujimoto, Kazuto

2015-08-01

Stenting may be a compelling approach to dilating curved lesions in congenital heart diseases. However, balloon-expandable stents, which are commonly used for congenital heart diseases, are usually deployed in a straight orientation. In this study, we evaluated the effect of stenting with a novel curved balloon considered to provide better conformability to the curved-angled lesion. In vitro experiments: A Palmaz Genesis(®) stent (Johnson & Johnson, Cordis Co, Bridgewater, NJ, USA) mounted on the Goku(®) curve (Tokai Medical Co. Nagoya, Japan) was dilated in vitro to observe directly the behavior of the stent and balloon assembly during expansion. Animal experiment: A short Express(®) Vascular SD (Boston Scientific Co, Marlborough, MA, USA) stent and a long Express(®) Vascular LD stent (Boston Scientific) mounted on the curved balloon were deployed in the curved vessel of a pig to observe the effect of stenting in vivo. In vitro experiments: Although the stent was dilated in a curved fashion, stent and balloon assembly also rotated conjointly during expansion of its curved portion. In the primary stenting of the short stent, the stent was dilated with rotation of the curved portion. The excised stent conformed to the curved vessel. As the long stent could not be negotiated across the mid-portion with the balloon in expansion when it started curving, the mid-portion of the stent failed to expand fully. Furthermore, the balloon, which became entangled with the stent strut, could not be retrieved even after complete deflation. This novel curved balloon catheter might be used for implantation of the short stent in a curved lesion; however, it should not be used for primary stenting of the long stent. Post-dilation to conform the stent to the angled vessel would be safer than primary stenting irrespective of stent length. Copyright © 2014 Japanese College of Cardiology. Published by Elsevier Ltd. All rights reserved.

Curve Boxplot: Generalization of Boxplot for Ensembles of Curves.

Science.gov (United States)

Mirzargar, Mahsa; Whitaker, Ross T; Kirby, Robert M

2014-12-01

In simulation science, computational scientists often study the behavior of their simulations by repeated solutions with variations in parameters and/or boundary values or initial conditions. Through such simulation ensembles, one can try to understand or quantify the variability or uncertainty in a solution as a function of the various inputs or model assumptions. In response to a growing interest in simulation ensembles, the visualization community has developed a suite of methods for allowing users to observe and understand the properties of these ensembles in an efficient and effective manner. An important aspect of visualizing simulations is the analysis of derived features, often represented as points, surfaces, or curves. In this paper, we present a novel, nonparametric method for summarizing ensembles of 2D and 3D curves. We propose an extension of a method from descriptive statistics, data depth, to curves. We also demonstrate a set of rendering and visualization strategies for showing rank statistics of an ensemble of curves, which is a generalization of traditional whisker plots or boxplots to multidimensional curves. Results are presented for applications in neuroimaging, hurricane forecasting and fluid dynamics.

Convective Heating of the LIFE Engine Target During Injection

Energy Technology Data Exchange (ETDEWEB)

Holdener, D S; Tillack, M S; Wang, X R

2011-10-24

Target survival in the hostile, high temperature xenon environment of the proposed Laser Inertial Fusion Energy (LIFE) engine is critical. This work focuses on the flow properties and convective heat load imposed upon the surface of the indirect drive target while traveling through the xenon gas. While this rarefied flow is traditionally characterized as being within the continuum regime, it is approaching transition where conventional CFD codes reach their bounds of operation. Thus ANSYS, specifically the Navier-Stokes module CFX, will be used in parallel with direct simulation Monte Carlo code DS2V and analytically and empirically derived expressions for heat transfer to the hohlraum for validation. Comparison of the viscous and thermal boundary layers of ANSYS and DS2V were shown to be nearly identical, with the surface heat flux varying less than 8% on average. From the results herein, external baffles have been shown to reduce this heat transfer to the sensitive laser entrance hole (LEH) windows and optimize target survival independent of other reactor parameters.

Comparative Effect of Heat Shock on Survival of O157:H7 and Non-O157 Shiga Toxigenic Escherichia coli and Salmonella in Lean Beef with or without Moisture-Enhancing Ingredients.

Science.gov (United States)

Vasan, Akhila; Ingham, Steven C; Ingham, Barbara H

2017-06-01

Thermal tolerance of pathogenic bacteria has been shown to increase after exposure to sublethal elevated temperatures, or heat shock. We evaluated the effect of heat shock at 48°C on thermal tolerance (D 55°C ) of cocktails of O157 and non-O157 Shiga toxigenic Escherichia coli (STEC) and Salmonella in lean ground beef with or without moisture-enhancing ingredients. Beef was moisture enhanced to 110% (w) with a 5% NaCl-2.5% sodium tripolyphosphate (w/w) brine. Meat, with or without added brine, was inoculated (∼10 8 CFU/g) and heat shocked at 48°C for 0, 5, or 30 min, followed by isothermal heating at 55°C. Inoculated control samples were unenhanced and were not subject to heat shock. From the linear portion of the log CFU per gram surviving cells over time plots, D 55°C -values (minutes) were calculated. D 55°C was 20.43, 28.78, and 21.15 min for O157, non-O157, and Salmonella controls, respectively. Overall, heat shock significantly increased D 55°C , regardless of pathogen (P moisture-enhanced meat (P Moisture-enhancing ingredients significantly increased D 55°C , regardless of pathogen (P moisture-enhanced beef products.

JUMPING THE CURVE

Directory of Open Access Journals (Sweden)

René Pellissier

2012-01-01

Full Text Available This paper explores the notion ofjump ing the curve,following from Handy 's S-curve onto a new curve with new rules policies and procedures. . It claims that the curve does not generally lie in wait but has to be invented by leadership. The focus of this paper is the identification (mathematically and inferentially ofthat point in time, known as the cusp in catastrophe theory, when it is time to change - pro-actively, pre-actively or reactively. These three scenarios are addressed separately and discussed in terms ofthe relevance ofeach.

Microencapsulation of alginate-immobilized bagasse with Lactobacillus rhamnosus NRRL 442: enhancement of survivability and thermotolerance.

Science.gov (United States)

Shaharuddin, Shahrulzaman; Muhamad, Ida Idayu

2015-03-30

The aim of this research was to enhance the survivability of Lactobacillus rhamnosus NRRL 442 against heat exposure via a combination of immobilization and microencapsulation processes using sugarcane bagasse (SB) and sodium alginate (NaA), respectively. The microcapsules were synthesized using different alginate concentration of 1, 2 and 3% and NaA:SB ratio of 1:0, 1:1 and 1:1.5. This beneficial step of probiotic immobilization before microencapsulation significantly enhanced microencapsulation efficiency and cell survivability after heat exposure of 90°C for 30s. Interestingly, the microcapsule of SB-immobilized probiotic could obtain protection from heat using microencapsulation of NaA concentration as low as 1%. SEM images illustrated the incorporation of immobilized L. rhamnosus within alginate matrices and its changes after heat exposure. FTIR spectra confirmed the change in functional bonding in the presence of sugarcane bagasse, probiotic and alginate. The results demonstrated a great potential in the synthesis of heat resistant microcapsules for probiotic. Copyright © 2014 Elsevier Ltd. All rights reserved.

Impact of periodontal maintenance on tooth survival in patients with removable partial dentures.

Science.gov (United States)

Tada, Sayaka; Allen, Patrick Finbarr; Ikebe, Kazunori; Matsuda, Ken-ichi; Maeda, Yoshinobu

2015-01-01

Removable partial dentures (RPDs) may have a negative impact on oral health and have the potential to cause further tooth loss, especially of abutment teeth. However, no evidence indicates the effective interval of regular periodontal maintenance after RPD provision. This practice-based cohort study aimed to examine the impact of regular periodontal maintenance visits on survival of RPD abutment teeth. One hundred and ninety-two patients had been previously provided with 304 new clasp-retained RPDs at Osaka University Dental Hospital, Japan. Using the Kaplan-Meier method and log-rank test, 1094 abutments were analysed to illustrate survival curves and to compare each curve. According to the frequency of periodontal maintenance, study samples were divided into three groups; every 3-6 months (3-6M) group, 1-year (1Y) group and no-maintenance (NM) group. Seven-year cumulative survival rates were 83.7% (3-6M), 75.5% (1Y) and 71.9% (NM) respectively. Survival of abutment teeth in the 3-6M group was significantly better than both 1Y (p = 0.005) and NM (p < 0.001) groups. These longitudinal clinical data indicates that periodontal maintenance at least once in 6 months had the most favourable outcome. Frequent periodontal maintenance after RPD provision could be effective in preventing further tooth loss. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Analysis of the location for peak heating in CHP based combined district heating systems

International Nuclear Information System (INIS)

Wang, Haichao; Lahdelma, Risto; Wang, Xin; Jiao, Wenling; Zhu, Chuanzhi; Zou, Pinghua

2015-01-01

Combined heat and power (CHP) is the main technology for providing the base load of district heating in China. However, CHP is not efficient for providing the peak load; instead, a peak boiler with high efficiency could be used to compensate the peak load. This paper studies how the location of the peak boiler can affect the energy efficiency and economic performance of such CHP based combined district heating system. Firstly, the connection mode and the control strategy for different peak heating locations are analyzed. Then the effect of the peak boiler's location on the initial investment of the network and the cost for distributing heat is studied. The objective is to place the peak boiler in a location where the overall costs are the smallest. Following this rule, the results indicate that the peak boiler should be located at the CHP plant if that allows using cheaper ‘self-use electricity’ in CHP for distributing the heat. However, if the market electricity price is used everywhere, or if energy efficiency is more emphasized, the location of the peak boiler should be closer to the users with dense heat loads. - Highlights: • Location for peak heating in the CHP based combined DH system is studied. • Regulation or control strategies for combined DH are summarized. • The heat load duration curve for combined DH is demonstrated. • Network design for combined DH with peak boiler outside of the CHP is analyzed

Liquid-liquid phase equilibrium and heat capacity of binary solution {2-propanol + 1-octyl-3-methylimidazolium hexafluorophosphate}

International Nuclear Information System (INIS)

Guo, Yimin; Zhang, Xianshuo; Xu, Chen; Shen, Weiguo

2017-01-01

Highlights: • Liquid-liquid equilibrium of binary {2-propanol + RTIL} solution was measured. • The critical exponents were deduced and found to belong to 3D-Ising universality. • Asymmetry of the coexistence curve was analyzed by the complete scaling theory. • The dependences of critical parameters on the permittivity of alkanols were discussed. - Abstract: The liquid-liquid coexistence curve and the heat capacity for binary solution of {2-propanol + 1-octyl-3-methylimidazolium hexafluorophosphate} have been precisely measured. The values of the critical exponents α and β, characterizing the critical anomalies of the heat capacity and the coexistence curve respectively, were deduced and found to be consistent with theoretical predictions. The asymmetric behavior of the diameter of the coexistence curve was studied in the frame of the complete scaling theory, demonstrating that the heat capacity related term is of importance. Furthermore, the restricted primitive model (RPM) was used to calculate the reduced upper consolute temperature and density, which together with a comparative larger value of A + indicated a character of solvophobic criticality.

Improved capacitive melting curve measurements

International Nuclear Information System (INIS)

Sebedash, Alexander; Tuoriniemi, Juha; Pentti, Elias; Salmela, Anssi

2009-01-01

Sensitivity of the capacitive method for determining the melting pressure of helium can be enhanced by loading the empty side of the capacitor with helium at a pressure nearly equal to that desired to be measured and by using a relatively thin and flexible membrane in between. This way one can achieve a nanobar resolution at the level of 30 bar, which is two orders of magnitude better than that of the best gauges with vacuum reference. This extends the applicability of melting curve thermometry to lower temperatures and would allow detecting tiny anomalies in the melting pressure, which must be associated with any phenomena contributing to the entropy of the liquid or solid phases. We demonstrated this principle in measurements of the crystallization pressure of isotopic helium mixtures at millikelvin temperatures by using partly solid pure 4 He as the reference substance providing the best possible universal reference pressure. The achieved sensitivity was good enough for melting curve thermometry on mixtures down to 100 μK. Similar system can be used on pure isotopes by virtue of a blocked capillary giving a stable reference condition with liquid slightly below the melting pressure in the reference volume. This was tested with pure 4 He at temperatures 0.08-0.3 K. To avoid spurious heating effects, one must carefully choose and arrange any dielectric materials close to the active capacitor. We observed some 100 pW loading at moderate excitation voltages.

Dual Smarandache Curves of a Timelike Curve lying on Unit dual Lorentzian Sphere

OpenAIRE

Kahraman, Tanju; Hüseyin Ugurlu, Hasan

2016-01-01

In this paper, we give Darboux approximation for dual Smarandache curves of time like curve on unit dual Lorentzian sphere. Firstly, we define the four types of dual Smarandache curves of a timelike curve lying on dual Lorentzian sphere.

Analysis of the convective heat transfer of a fluid flow over an ...

African Journals Online (AJOL)

Convective heat transfer in a homogeneous fluid flow Reynolds number of order less than 2000 over an immersed axi-symmetrical body with curved surfaces has been investigated. The fluid flow in consideration was unsteady and of constant density .This study analysed the extent to which convective heat transfer has on ...

The fall of the black hole firewall: natural nonmaximal entanglement for the Page curve

Science.gov (United States)

Hotta, Masahiro; Sugita, Ayumu

2015-12-01

The black hole firewall conjecture is based on the Page curve hypothesis, which claims that entanglement between a black hole and its Hawking radiation is almost maximum. Adopting canonical typicality for nondegenerate systems with nonvanishing Hamiltonians, we show the entanglement becomes nonmaximal, and energetic singularities (firewalls) do not emerge for general systems. An evaporating old black hole must evolve in Gibbs states with exponentially small error probability after the Page time as long as the states are typical. This means that the ordinarily used microcanonical states are far from typical. The heat capacity computed from the Gibbs states should be nonnegative in general. However, the black hole heat capacity is actually negative due to the gravitational instability. Consequently the states are not typical until the last burst. This requires inevitable modification of the Page curve, which is based on the typicality argument. For static thermal pure states of a large AdS black hole and its Hawking radiation, the entanglement entropy equals the thermal entropy of the smaller system.

The role of heat resistance in thermorestoration of hydrated bacterial spores

International Nuclear Information System (INIS)

Friedman, Y.S.; Grecz, N.

1973-01-01

This study for the first time presents evidence of the distinct role played in thermorestoration by cellular determinants such as the resistance to heat and radiation, and the ionic state of spores. In the past only radiochemical determinants associated with radical annealment have been studied in hydrated systems. The basic heat resistance of spores plays a significant role in the precipitous drop in spore survival due to 0.45 Mrad radiation plus heat above 65-75 0 C for B.cereus and 75-95 0 C for B.stearothermophilus. The effect of the spores radiation resistance was not distinct except in the frozen state and at the saturation plateau of thermorestoration where the radiation resistant B.cereus showed ca. 1 log cycle higher survival than the radiation sensitive B.stearothermophilus. When spores are chemically converted into their H + and Ca ++ ionic forms, the H + spores are distinctly more responsive than Ca ++ spores to processes of radical annealment responsible for thermorestoration in hydrated spore systems. At temperatures of extensive thermorestoration of water radicals, H + spores showed higher survival than Ca ++ spores. (F.J.)

ECM using Edwards curves

DEFF Research Database (Denmark)

Bernstein, Daniel J.; Birkner, Peter; Lange, Tanja

2013-01-01

-arithmetic level are as follows: (1) use Edwards curves instead of Montgomery curves; (2) use extended Edwards coordinates; (3) use signed-sliding-window addition-subtraction chains; (4) batch primes to increase the window size; (5) choose curves with small parameters and base points; (6) choose curves with large...

Pressure drop-flow rate curves for single-phase steam in Combustion Engineering type steam generator U-tubes during severe accidents

Energy Technology Data Exchange (ETDEWEB)

Fynan, Douglas A.; Ahn, Kwang-Il, E-mail: kiahn@kaeri.re.kr

2016-12-15

Highlights: • Pressure drop-flow rate curves for superheated steam in U-tubes were generated. • Forward flow of hot steam is favored in the longer and taller U-tubes. • Reverse flow of cold steam is favored in short U-tubes. • Steam generator U-tube bundle geometry and tube diameter are important. • Need for correlation development for natural convention heat transfer coefficient. - Abstract: Characteristic pressure drop-flow rate curves are generated for all row numbers of the OPR1000 steam generators (SGs), representative of Combustion Engineering (CE) type SGs featuring square bend U-tubes. The pressure drop-flow rate curves are applicable to severe accident natural circulations of single-phase superheated steam during high pressure station blackout sequences with failed auxiliary feedwater and dry secondary side which are closely related to the thermally induced steam generator tube rupture event. The pressure drop-flow rate curves which determine the recirculation rate through the SG tubes are dependent on the tube bundle geometry and hydraulic diameter of the tubes. The larger CE type SGs have greater variation of tube length and height as a function of row number with forward flow of steam favored in the longer and taller high row number tubes and reverse flow favored in the short low row number tubes. Friction loss, natural convection heat transfer coefficients, and temperature differentials from the primary to secondary side are dominant parameters affecting the recirculation rate. The need for correlation development for natural convection heat transfer coefficients for external flow over tube bundles currently not modeled in system codes is discussed.

Specific heat study of quasi-one-dimensional antiferromagnetic model for an organic polymer chain

International Nuclear Information System (INIS)

Qu Shaohua; Zhu Lin

2008-01-01

The specific heat of an infinite one-dimensional polymer chain bearing periodically arranged side radicals connected to the even sites is studied by means of quantum transfer-matrix method based on a Ising-Heisenberg model. In the absence of the exchange interactions between side radicals and the main chain, the curves of specific heat show a round peak due to the antiferromagnetic excitations for the all antiferromagnetic interactions along the polymer chain. Considering the exchange interactions between the side radicals and the main chain, the curves of the specific heat show double-peak structure for ferromagnetic interactions between the radicals and main chain, indicating that a competition between ferromagnetic and antiferromagnetic interactions and the possibility of the occurrence of the stable ferrimagnetic state along the polymer chain

Turbulent boundary layer heat transfer experiments: Convex curvature effects including introduction and recovery

Science.gov (United States)

Simon, T. W.; Moffat, R. J.; Johnston, J. P.; Kays, W. M.

1982-01-01

Measurements were made of the heat transfer rate through turbulent and transitional boundary layers on an isothermal, convexly curved wall and downstream flat plate. The effect of convex curvature on the fully turbulent boundary layer was a reduction of the local Stanton numbers 20% to 50% below those predicted for a flat wall under the same circumstances. The recovery of the heat transfer rates on the downstream flat wall was extremely slow. After 60 cm of recovery length, the Stanton number was still typically 15% to 20% below the flat wall predicted value. Various effects important in the modeling of curved flows were studied separately. These are: the effect of initial boundary layer thickness, the effect of freestream velocity, the effect of freestream acceleration, the effect of unheated starting length, and the effect of the maturity of the boundary layer. An existing curvature prediction model was tested against this broad heat transfer data base to determine where it could appropriately be used for heat transfer predictions.

Temperature Dependence and Magnetic Properties of Injection Molding Tool Materials Used in Induction Heating

DEFF Research Database (Denmark)

Guerrier, Patrick; Nielsen, Kaspar Kirstein; Hattel, Jesper Henri

2015-01-01

To analyze the heating phase of an induction heated injection molding tool precisely, the temperature-dependent magnetic properties, B–H curves, and the hysteresis loss are necessary for the molding tool materials. Hence, injection molding tool steels, core materials among other materials have...

Effect of heating rates of crystallization behaviour of amorphous Fe/sub 83/01/B/sub 17/ alloy

International Nuclear Information System (INIS)

Ashfaq, A.; Shamim, A.

1993-01-01

The electric resistivity of amorphous Fe/sub 83/01/B/sub 17/ alloy has been measured to study its crystallization behaviour from room temperature to about 900 K at the constant heating rates of 40, 60 and 80 K/hr. The crystallization temperature was observed to increase with the increase of heating g rate. However amorphous to crystalline path of RT-curve between the maximum and the minimum decreases with heating rate. The Resistivity Temperature (RT) curves exhibit different steps which are shown to correspond to the phase change stages of the alloy. The slope of the rt-curve after the previous step increases with the rise in heating rate and finally passes through a board peak and then rises again. From the peak shift dta of first crystallization stage activation energy was calculated by applying various peak shift equations. The values so obtained were in good agreement with those obtained with DSC measurement for (FeM)/sub 83/01/B/sub 17/ amorphous alloys where M=Mo, Ni, Cr, and V. (author)

Technological change in energy systems. Learning curves, logistic curves and input-output coefficients

International Nuclear Information System (INIS)

Pan, Haoran; Koehler, Jonathan

2007-01-01

Learning curves have recently been widely adopted in climate-economy models to incorporate endogenous change of energy technologies, replacing the conventional assumption of an autonomous energy efficiency improvement. However, there has been little consideration of the credibility of the learning curve. The current trend that many important energy and climate change policy analyses rely on the learning curve means that it is of great importance to critically examine the basis for learning curves. Here, we analyse the use of learning curves in energy technology, usually implemented as a simple power function. We find that the learning curve cannot separate the effects of price and technological change, cannot reflect continuous and qualitative change of both conventional and emerging energy technologies, cannot help to determine the time paths of technological investment, and misses the central role of R and D activity in driving technological change. We argue that a logistic curve of improving performance modified to include R and D activity as a driving variable can better describe the cost reductions in energy technologies. Furthermore, we demonstrate that the top-down Leontief technology can incorporate the bottom-up technologies that improve along either the learning curve or the logistic curve, through changing input-output coefficients. An application to UK wind power illustrates that the logistic curve fits the observed data better and implies greater potential for cost reduction than the learning curve does. (author)

Heat flux microsensor measurements and calibrations

Science.gov (United States)

Terrell, James P.; Hager, Jon M.; Onishi, Shinzo; Diller, Thomas E.

1992-01-01

A new thin-film heat flux gage has been fabricated specifically for severe high temperature operation using platinum and platinum-10 percent rhodium for the thermocouple elements. Radiation calibrations of this gage were performed at the AEDC facility over the available heat flux range (approx. 1.0 - 1,000 W/cu cm). The gage output was linear with heat flux with a slight increase in sensitivity with increasing surface temperature. Survivability of gages was demonstrated in quench tests from 500 C into liquid nitrogen. Successful operation of gages to surface temperatures of 750 C has been achieved. No additional cooling of the gages is required because the gages are always at the same temperature as the substrate material. A video of oxyacetylene flame tests with real-time heat flux and temperature output is available.

Trends in adult leukemia incidence and survival in Denmark, 1943-2003

DEFF Research Database (Denmark)

Thygesen, Lau Caspar; Nielsen, Ove Juul; Johansen, Christoffer

2009-01-01

The etiology of leukemia is largely unknown. Ecological data indicating trends in incidence and survival can provide information about changes in risk factors, can reflect underlying changes in diagnostic classification, and can measure therapeutic advances. From the records of the Danish Cancer...... Registry with registration starting from 1943, we calculated age-specific, period-specific, and age-standardized (world standard) incidence rates of chronic lymphoid leukemia (CLL), acute lymphoid leukemia (ALL), chronic myeloid leukemia (CML), and acute myeloid leukemia (AML) for persons above the age...... of 18. Kaplan-Meier survival curves and median survival times were calculated. Between 1943 and 2003, there were 26,036 cases of leukemia reported. The age-specific incidence rates of CLL, CML, and AML were higher for older men and women, while the incidence rates of ALL by age were more homogeneous...

Cooling of Accretion-Heated Neutron Stars

Indian Academy of Sciences (India)

Rudy Wijnands

2017-09-12

Sep 12, 2017 ... the magnetic field might play an important role in the heating and cooling of the neutron stars. .... Source near Sgr A ..... marked the start of the research field that uses the cool- ... This curve is just to guide the eye for the individual sources and it is clear ..... Not all accretion-induced nuclear reactions might.

A novel NGL (natural gas liquid) recovery process based on self-heat recuperation

International Nuclear Information System (INIS)

Van Duc Long, Nguyen; Lee, Moonyong

2013-01-01

This study examined an innovative self-heat-recuperation technology that circulates latent and sensible heat in the thermal process and applied it to the NGL (natural gas liquid) recovery process. A CGCC (column grand composite curve) was used to assess the thermodynamic feasibility of implementing the heat pump system and self-heat-recuperation technology into a conventional distillation column. The proposed distillation based on self-heat recuperation reduced the energy consumption dramatically by compressing the effluent stream, whose temperature was increased to provide the minimum temperature difference for the heat exchanger, and circulating the stream heat in the process. According to a simulation of the proposed sequence, up to 73.43 and 83.48% of the condenser and reboiler energy, respectively, were saved compared to a conventional column. This study also proposes heat integration to improve the performance of self-heat recuperation. The results showed that the modified sequence saves up 64.35, 100.00 and 31.60% of the condenser energy requirements, reboiler energy requirements and OP (operating cost), respectively, compared to a classical heat pump system, and 90.24, 100.00, and 67.19%, respectively, compared to a conventional column. The use of these sequences to retrofit a distillation column to save energy was also considered. - Highlights: • Innovative self-heat-recuperation technology that circulates latent and sensible heat. • A CGCC (column grand composite curve) is used to assess the thermodynamic feasibility. • The proposed sequence saves up 67.19% of the OP (operating cost). • The proposed sequences can be used to retrofit a distillation column to save energy

Development and External Validation of Prognostic Model for 2-Year Survival of Non-Small-Cell Lung Cancer Patients Treated With Chemoradiotherapy

International Nuclear Information System (INIS)

Dehing-Oberije, Cary; Yu Shipeng; De Ruysscher, Dirk; Meersschout, Sabine; Van Beek, Karen; Lievens, Yolande; Van Meerbeeck, Jan; De Neve, Wilfried; Rao, Bharat Ph.D.; Weide, Hiska van der; Lambin, Philippe

2009-01-01

Purpose: Radiotherapy, combined with chemotherapy, is the treatment of choice for a large group of non-small-cell lung cancer (NSCLC) patients. Recent developments in the treatment of these patients have led to improved survival. However, the clinical TNM stage is highly inaccurate for the prediction of survival, and alternatives are lacking. The objective of this study was to develop and validate a prediction model for survival of NSCLC patients, treated with chemoradiotherapy. Patients and Methods: The clinical data from 377 consecutive inoperable NSCLC patients, Stage I-IIIB, treated radically with chemoradiotherapy were collected. A prognostic model for 2-year survival was developed, using 2-norm support vector machines. The performance of the model was expressed as the area under the curve of the receiver operating characteristic and assessed using leave-one-out cross-validation, as well as two external data sets. Results: The final multivariate model consisted of gender, World Health Organization performance status, forced expiratory volume in 1 s, number of positive lymph node stations, and gross tumor volume. The area under the curve, assessed by leave-one-out cross-validation, was 0.74, and application of the model to the external data sets yielded an area under the curve of 0.75 and 0.76. A high- and low-risk group could be clearly identified using a risk score based on the model. Conclusion: The multivariate model performed very well and was able to accurately predict the 2-year survival of NSCLC patients treated with chemoradiotherapy. The model could support clinicians in the treatment decision-making process.

ISOCHORIC HEAT CAPACITY OF 1% AQUEOUS SOLUTION OF MAGNESIUM CHLORIDE

Directory of Open Access Journals (Sweden)

V. I. Dvoryanchikov

2016-01-01

Full Text Available Aim. The aim is to conduct an experimental study of isochoric heat capacity of 1% aqueous solution of magnesium chloride along the phase boundary curve.Method. In order to determine the isochoric heat capacity at the phase boundary curve we used the adiabatic calorimeter of KH. I. Amirkhanov.Results. Results of the study of the isochoric heat capacity depending on the temperature are given in tables and figures; the findings are compared with those of other researchers. When evaluating a complex system, we ought not to evaluate its effectiveness on the basis of only one criterion, even a very important, in this case must take into account the requirements of the technical, economic, environmental and of other natures.Conclusions. When solving optimization problems of efficiency in geothermal energy it is necessary to take into account the fact of the temperature dependence of the heat and density. The temperature dependence of the density and heat capacity in the calculations significantly affect the value of the efficiency criterion to be taken into account, otherwise the calculation error can be up to 20%. The data obtained from the isochoric heat capacity of aqueous solutions of magnesium chloride is compared with the data for water and aqueous solutions of NaCl and NaOH, obtained previously, which may be represented as a model of geothermal and sea water.

A Simple Calorimetric Experiment that Highlights Aspects of Global Heat Retention and Global Warming

Science.gov (United States)

Burley, Joel D.; Johnston, Harold S.

2007-01-01

In this laboratory experiment, general chemistry students measure the heating curves for three different systems: (i) 500 g of room-temperature water heated by a small desk lamp, (ii) 500 g of an ice-water mixture warmed by conduction with room-temperature surroundings, and (iii) 500 g of an ice-water mixture heated by a small desk lamp and by…

The influence of a vertical ground heat exchanger length on the electricity consumption of the heat pumps

Energy Technology Data Exchange (ETDEWEB)

Michopoulos, A.; Kyriakis, N. [Process Equipment Design Laboratory, Mechanical Engineer Department, Aristotle University of Thessaloniki (AUTh), P.O. Box 487, 541 24 Thessaloniki (Greece)

2010-07-15

The use of heat pumps combined with vertical ground heat exchangers for heating and cooling of buildings, has significantly gained popularity in recent years. The design method for these systems, as it is proposed by ASHRAE, is taking into account the maximum thermal and cooling loads of the building, the thermophysical properties of the soil at the area of installation and a minimum Coefficient of Performance (COP) of the heat pumps. This approach usually results in larger than needed length of the ground heat exchanger, thus increasing the installation cost. A new analytical simulation tool, capable to determine the required ground heat exchanger length has been developed at the Process Equipment Design Laboratory (PEDL) of the AUTh. It models the function of the system as a whole over long time periods, e.g. 20 years, using as input parameters the thermal and cooling loads of the building, the thermophysical properties of the borehole and the characteristic curves of the heat pumps. The results include the electricity consumption of the heat pumps and the heat absorbed from or rejected to the ground. The aim of this paper is to describe the developed simulation algorithm and present the results of such a simulation in a case study. It is proved that the total required length of the ground heat exchanger is less than that calculated using the common numerical method. (author)

Description of heat flux measurement methods used in hydrocarbon and propellant fuel fires at Sandia.

Energy Technology Data Exchange (ETDEWEB)

Nakos, James Thomas

2010-12-01

The purpose of this report is to describe the methods commonly used to measure heat flux in fire applications at Sandia National Laboratories in both hydrocarbon (JP-8 jet fuel, diesel fuel, etc.) and propellant fires. Because these environments are very severe, many commercially available heat flux gauges do not survive the test, so alternative methods had to be developed. Specially built sensors include 'calorimeters' that use a temperature measurement to infer heat flux by use of a model (heat balance on the sensing surface) or by using an inverse heat conduction method. These specialty-built sensors are made rugged so they will survive the environment, so are not optimally designed for ease of use or accuracy. Other methods include radiometers, co-axial thermocouples, directional flame thermometers (DFTs), Sandia 'heat flux gauges', transpiration radiometers, and transverse Seebeck coefficient heat flux gauges. Typical applications are described and pros and cons of each method are listed.

Computational Fluid Dynamics Based Extraction of Heat Transfer Coefficient in Cryogenic Propellant Tanks

Science.gov (United States)

Yang, H. Q.; West, Jeff

2015-01-01

Current reduced-order thermal model for cryogenic propellant tanks is based on correlations built for flat plates collected in the 1950's. The use of these correlations suffers from: inaccurate geometry representation; inaccurate gravity orientation; ambiguous length scale; and lack of detailed validation. The work presented under this task uses the first-principles based Computational Fluid Dynamics (CFD) technique to compute heat transfer from tank wall to the cryogenic fluids, and extracts and correlates the equivalent heat transfer coefficient to support reduced-order thermal model. The CFD tool was first validated against available experimental data and commonly used correlations for natural convection along a vertically heated wall. Good agreements between the present prediction and experimental data have been found for flows in laminar as well turbulent regimes. The convective heat transfer between tank wall and cryogenic propellant, and that between tank wall and ullage gas were then simulated. The results showed that commonly used heat transfer correlations for either vertical or horizontal plate over predict heat transfer rate for the cryogenic tank, in some cases by as much as one order of magnitude. A characteristic length scale has been defined that can correlate all heat transfer coefficients for different fill levels into a single curve. This curve can be used for the reduced-order heat transfer model analysis.

Revealing the equivalence of two clonal survival models by principal component analysis

International Nuclear Information System (INIS)

Lachet, Bernard; Dufour, Jacques

1976-01-01

The principal component analysis of 21 chlorella cell survival curves, adjusted by one-hit and two-hit target models, lead to quite similar projections on the principal plan: the homologous parameters of these models are linearly correlated; the reason for the statistical equivalence of these two models, in the present state of experimental inaccuracy, is revealed [fr

Anomalies and other concerns related to the critical heat flux

Energy Technology Data Exchange (ETDEWEB)

Groeneveld, D.C., E-mail: thermal@magma.ca [Researcher Emeritus, Chalk River Laboratories, Atomic Energy of Canada Ltd, Chalk River (Canada) and University of Ottawa, Department of Mechanical Engineering, Ottawa (Canada)

2011-11-15

This paper summarizes various unusual trends in the critical heat flux (CHF) that have been observed experimentally in tubes or bundle subassemblies. They include the following: Bullet Occurrence of a minimum in the CHF vs. quality (X) curve at high flows - leading to an initial upstream CHF occurrence in uniformly heated channels. This phenomenon has been observed at high flows in both water and Freon. Bullet Occurrence of a limiting quality region on the CHF vs. X curve where the CHF drops by 30-90% for a nearly constant quality. This is thought to correspond to the boundary between the entrainment controlled and the deposition controlled region and causes problems for prediction methods of the form CHF = f(X). Bullet Impact of flow obstructions on the occurrence of upstream CHF and the limiting quality region. The additional mixing by grid spacers or bundle appendages results in a more homogeneous phase distribution, and diminishes the effects of flow regime/heat transfer regime transitions responsible for some of the unusual CHF trends, and results in a more gradually decreasing CHF vs. X curve. Bullet Absence of a CHF temperature excursion at high flows and high qualities - this is found to be caused by a change in slope of the transition boiling part of the boiling curve from a negative value (usual trend that results in a temperature excursion) to a positive slope. Bullet Gradual disappearance of the sharp temperature excursion at CHF when increasing the pressure towards and beyond the critical pressure - no drastic change is observed in the axial temperature distribution of a heated tube experiencing CHF when, for constant mass flux and inlet temperature, the pressure is gradually increased from subcritical to supercritical. Bullet CHF fluid-to-fluid modelling: differences in CHF trends at certain conditions between refrigerants and water at equivalent conditions. The mechanisms responsible for these trends and the implications for bundle geometries are

Survival chance in papillary thyroid cancer in Hungary: individual survival probability estimation using the Markov method

International Nuclear Information System (INIS)

Esik, Olga; Tusnady, Gabor; Daubner, Kornel; Nemeth, Gyoergy; Fuezy, Marton; Szentirmay, Zoltan

1997-01-01

Purpose: The typically benign, but occasionally rapidly fatal clinical course of papillary thyroid cancer has raised the need for individual survival probability estimation, to tailor the treatment strategy exclusively to a given patient. Materials and methods: A retrospective study was performed on 400 papillary thyroid cancer patients with a median follow-up time of 7.1 years to establish a clinical database for uni- and multivariate analysis of the prognostic factors related to survival (Kaplan-Meier product limit method and Cox regression). For a more precise prognosis estimation, the effect of the most important clinical events were then investigated on the basis of a Markov renewal model. The basic concept of this approach is that each patient has an individual disease course which (besides the initial clinical categories) is affected by special events, e.g. internal covariates (local/regional/distant relapses). On the supposition that these events and the cause-specific death are influenced by the same biological processes, the parameters of transient survival probability characterizing the speed of the course of the disease for each clinical event and their sequence were determined. The individual survival curves for each patient were calculated by using these parameters and the independent significant clinical variables selected from multivariate studies, summation of which resulted in a mean cause-specific survival function valid for the entire group. On the basis of this Markov model, prediction of the cause-specific survival probability is possible for extrastudy cases, if it is supposed that the clinical events occur within new patients in the same manner and with the similar probability as within the study population. Results: The patient's age, a distant metastasis at presentation, the extent of the surgical intervention, the primary tumor size and extent (pT), the external irradiation dosage and the degree of TSH suppression proved to be

Synthesis and thermotolerance of heat shock proteins in Campylobacter jejuni

International Nuclear Information System (INIS)

Kim, C.K.; Kim, H.O.; Lee, K.J.

1991-01-01

The heat shock responses of Campylobacter jejuni were studied by examination of their survival rates and synthesis of heat shock proteins. When C. jejuni cells were treated at the sublethal temperatures of 48C° for 30 minutes, most of the cells maintained their viabilities and synthesized the heat shock proteins of 90, 73, and 66 kD in molecular weight. By the method of two-dimensional electrophoresis, the heat shock proteins of C. jejuni were identified to be Hsp90, Hsp73, and Hsp66. During the heat shock at 48C°, the heat shock proteins were induced from about 5 minutes after the heat shock treatment. Their synthesis was continued upto 30 minutes, but remarkably retarded after 50 minutes. When C. jejune cells were heat shocked at 51C° for 30 minutes, the survival rates of the cells were decreased by about 10 3 fold and synthesis of heat shock proteins and normal proteins was also generally retarded. The cells exposed to 55C° for 30 minutes died off by more than 10 5 cells and the new protein synthesis was not observed. But when C. jejuni cells were heat-shocked at the sublethal temperature of 48C° for 15 to 20 minutes and then were exposed at the lethal temperature of 55C° for 30 minutes, their viabilities were higher than those exposed at 55C° for 30 minutes without pre-heat shock at 48C°. Therefore, the heat shock proteins synthesized at the sublethal temperature of 48C° in C. jejuni were thought to be responsible for thermotolerance. However, when C. jejuni cells heat-shocked at various ranges of sublethal and lethal temperatures were placed back to the optimum temperature of 42C°, the multiplication patterns of the cells pretreated at different temperatures were not much different each other

B-ducted Heating of Black Widow Companions

Energy Technology Data Exchange (ETDEWEB)

Sanchez, Nicolas; Romani, Roger W., E-mail: rwr@astro.stanford.edu [Department of Physics, Stanford University, Stanford, CA 94305-4060 (United States)

2017-08-10

The companions of evaporating binary pulsars (black widows and related systems) show optical emission suggesting strong heating. In a number of cases, large observed temperatures and asymmetries are inconsistent with direct radiative heating for the observed pulsar spindown power and expected distance. Here we describe a heating model in which the pulsar wind sets up an intrabinary shock (IBS) against the companion wind and magnetic field, and a portion of the shock particles duct along this field to the companion magnetic poles. We show that a variety of heating patterns, and improved fits to the observed light curves, can be obtained at expected pulsar distances and luminosities, at the expense of a handful of model parameters. We test this “IBS-B” model against three well-observed binaries and comment on the implications for system masses.

Concept of heat-induced inkless eco-printing.

Science.gov (United States)

Chen, Jinxiang; Wang, Yong; Xie, Juan; Meng, Chuang; Wu, Gang; Zu, Qiao

2012-07-01

Existing laser and inkjet printers often produce adverse effects on human health, the recycling of printing paper and the environment. Therefore, this paper examines the thermogravimetry curves for printer paper, analyzes the discoloration of paper using heat-induction, and investigates the relationship between paper discoloration and the heat-inducing temperature. The mechanism of heat-induced printing is analyzed initially, and its feasibility is determined by a comparative analysis of heat-induced (laser ablation) printing and commercial printing. The innovative concept of heat-induced inkless eco-printing is proposed, in which the required text or graphics are formed on the printing paper via yellowing and blackening produced by thermal energy. This process does not require ink during the printing process; thus, it completely eliminates the aforementioned health and environmental issues. This research also contributes to related interdisciplinary research in biology, laser technology, photochemistry, nano-science, paper manufacturing and color science. Copyright © 2012 Elsevier Ltd. All rights reserved.

Computerised curve deconvolution of TL/OSL curves using a popular spreadsheet program.

Science.gov (United States)

Afouxenidis, D; Polymeris, G S; Tsirliganis, N C; Kitis, G

2012-05-01

This paper exploits the possibility of using commercial software for thermoluminescence and optically stimulated luminescence curve deconvolution analysis. The widely used software package Microsoft Excel, with the Solver utility has been used to perform deconvolution analysis to both experimental and reference glow curves resulted from the GLOw Curve ANalysis INtercomparison project. The simple interface of this programme combined with the powerful Solver utility, allows the analysis of complex stimulated luminescence curves into their components and the evaluation of the associated luminescence parameters.

Computerised curve deconvolution of TL/OSL curves using a popular spreadsheet program

International Nuclear Information System (INIS)

Afouxenidis, D.; Polymeris, G. S.; Tsirliganis, N. C.; Kitis, G.

2012-01-01

This paper exploits the possibility of using commercial software for thermoluminescence and optically stimulated luminescence curve deconvolution analysis. The widely used software package Microsoft Excel, with the Solver utility has been used to perform deconvolution analysis to both experimental and reference glow curves resulted from the Glow Curve Analysis Intercomparison project. The simple interface of this programme combined with the powerful Solver utility, allows the analysis of complex stimulated luminescence curves into their components and the evaluation of the associated luminescence parameters. (authors)

Parametric investigation on transient boiling heat transfer of metal rod cooled rapidly in water pool

Energy Technology Data Exchange (ETDEWEB)

Lee, Chi Young [Department of Fire Protection Engineering, Pukyong National University, 45, Yongso-ro, Nam-gu, Busan 48513 (Korea, Republic of); Kim, Sunwoo, E-mail: swkim@alaska.edu [Mechanical Engineering Department, University of Alaska Fairbanks, P. O. Box 755905, Fairbanks, AK 99775-5905 (United States)

2017-03-15

Highlights: • Effects of liquid subcooling, surface coating, material property, and surface oxidation are examined. • Liquid subcooling affects remarkably the quenching phenomena. • Cr-coated surfaces for ATF might extend the quenching duration. • Solids with low heat capacity shorten the quenching duration. • Surface oxidation can affect strongly the film boiling heat transfer and MFB point. - Abstract: In this work, the effects of liquid subcooling, surface coating, material property, and surface oxidation on transient pool boiling heat transfer were investigated experimentally using the vertical metal rod and quenching method. The change in rod temperature was measured with time during quenching, and the visualization of boiling around the test specimen was performed using the high-speed video camera. As the test materials, the zircaloy (Zry), stainless steel (SS), niobium (Nb), and copper (Cu) were tested. In addition, the chromium-coated niobium (Cr-Nb) and chromium-coated stainless steel (Cr-SS) were prepared for accident tolerant fuel (ATF) application. Low liquid subcooling and Cr-coating shifted the quenching curve to the right, which indicates a prolongation of quenching duration. On the other hand, the material with small heat capacity and surface oxidation caused the quenching curve to move to the left. To examine the influence of the material property and surface oxidation on the film boiling heat transfer performance and minimum film boiling (MFB) point in more detail, the wall temperature and heat flux were calculated from the present transient temperature profile using the inverse heat transfer analysis, and then the curves of wall temperature and heat flux in the film boiling regime were obtained. In the present experimental conditions, the effect of material property on the film boiling heat transfer performance and MFB point seemed to be minor. On the other hand, based on the experimental results of the Cu test specimen, the surface

Evaluation of the a.c. potential drop method to determine J-crack resistance curves for a pressure vessel steel

International Nuclear Information System (INIS)

Gibson, G.P.

1989-01-01

An evaluation has been carried out of the a.c. potential drop technique for determining J-crack growth resistance curves for a pressure vessel steel. The technique involves passing an alternating current through the specimen and relating the changes in the potential drop across the crack mouth to changes in crack length occuring during the test. The factors investigated were the current and voltage probe positions, the a.c. frequency and the test temperature. In addition, by altering the heat treatment of the material, J-crack resistance curves were obtained under both contained and non-contained yielding conditions. In all situations, accurate J-R curves could be determined. (author)

ICRF heating on helical devices

International Nuclear Information System (INIS)

Rasmussen, D.A.; Lyon, J.F.; Hoffman, D.J.; Murakami, M.; England, A.C.; Wilgen, J.B.; Jaeger, E.F.; Wang, C.; Batchelor, D.B.

1995-01-01

Ion cyclotron range of frequency (ICRF) heating is currently in use on CHS and W7-AS and is a major element of the heating planned for steady state helical devices. In helical devices, the lack of a toroidal current eliminates both disruptions and the need for ICRF current drive, simplifying the design of antenna structures as compared to tokamak applications. However the survivability of plasma facing components and steady state cooling issues are directly applicable to tokamak devices. Results from LHD steady state experiments should be available on a time scale to strongly influence the next generation of steady state tokamak experiments. The helical plasma geometry provides challenges not faced with tokamak ICRF heating, including the potential for enhanced fast ion losses, impurity accumulation, limited access for antenna structures, and open magnetic field lines in the plasma edge. The present results and near term plans provide the basis for steady state ICRF heating of larger helical devices. An approach which includes direct electron, mode conversion, ion minority and ion Bernstein wave heating addresses these issues

ICRF heating on helical devices

International Nuclear Information System (INIS)

Rasmussen, D.A.; Lyon, J.F.; Hoffman, D.J.

1995-01-01

Ion cyclotron range of frequency (ICRF) heating is currently in use on CHS and W7AS and is a major element of the heating planned for steady state helical devices. In helical devices, the lack of a toroidal current eliminates both disruptions and the need for ICRF current drive, simplifying the design of antenna structures as compared to tokamak applications. However the survivability of plasma facing components and steady state cooling issues are directly applicable to tokamak devices. Results from LHD steady state experiments should be available on a time scale to strongly influence the next generation of steady state tokamak experiments. The helical plasma geometry provides challenges not faced with tokamak ICRF heating, including the potential for enhanced fast ion losses, impurity accumulation, limited access for antenna structures, and open magnetic field lines in the plasma edge. The present results and near term plans provide the basis for steady state ICRF heating of larger helical devices. An approach which includes direct electron, mode conversion, ion minority and ion Bernstein wave heating addresses these issues

Heat demand profiles of energy conservation measures in buildings and their impact on a district heating system

International Nuclear Information System (INIS)

Lundström, Lukas; Wallin, Fredrik

2016-01-01

Highlights: • Energy savings impact on an low CO 2 emitting district heating system. • Heat profiles of eight building energy conservation measures. • Exhaust air heat pump, heat recovery ventilation, electricity savings etc. • Heat load weather normalisation with segmented multivariable linear regression. - Abstract: This study highlights the forthcoming problem with diminishing environmental benefits from heat demand reducing energy conservation measures (ECM) of buildings within district heating systems (DHS), as the supply side is becoming “greener” and more primary energy efficient. In this study heat demand profiles and annual electricity-to-heat factors of ECMs in buildings are computed and their impact on system efficiency and greenhouse gas emissions of a Swedish biomass fuelled and combined heat and power utilising DHS are assessed. A weather normalising method for the DHS heat load is developed, combining segmented multivariable linear regressions with typical meteorological year weather data to enable the DHS model and the buildings model to work under the same weather conditions. Improving the buildings’ envelope insulation level and thereby levelling out the DHS heat load curve reduces greenhouse gas emissions and improves primary energy efficiency. Reducing household electricity use proves to be highly beneficial, partly because it increases heat demand, allowing for more cogeneration of electricity. However the other ECMs considered may cause increased greenhouse gas emissions, mainly because of their adverse impact on the cogeneration of electricity. If biomass fuels are considered as residuals, and thus assigned low primary energy factors, primary energy efficiency decreases when implementing ECMs that lower heat demand.

Numerical calibration and experimental validation of a PCM-Air heat exchanger model

International Nuclear Information System (INIS)

Stathopoulos, N.; El Mankibi, M.; Santamouris, Mattheos

2017-01-01

Highlights: • Development of a PCM-Air heat exchanger experimental unit and its numerical model. • Differential Scanning Calorimetry for PCM properties. • Ineptitude of DSC obtained heat capacity curves. • Creation of adequate heat capacity curves depending on heat transfer rates. • Confrontation of numerical and experimental results and validation of the model. - Abstract: Ambitious goals have been set at international, European and French level for energy consumption and greenhouse gas emissions decrease of the building sector. Achieving them requires renewable energy integration, a technology that presents however an important drawback: intermittent energy production. In response, thermal energy storage (TES) technology applications have been developed in order to correlate energy production and consumption of the building. Phase Change Materials (PCMs) have been widely used in TES applications as they offer a high storage density and adequate phase change temperature range. It is important to accurately know the thermophysical properties of the PCM, both for experimental (system design) and numerical (correct prediction) purposes. In this paper, the fabrication of a PCM – Air experimental prototype is presented at first, along with the development of a numerical model simulating the downstream temperature evolution of the heat exchanger. Particular focus is given to the calibration method and the validation of the model using experimental characterization results. Differential scanning calorimetry (DSC) is used to define the thermal properties of the PCM. Initial numerical results are underestimated compared to experimental ones. Various factors were investigated, pointing to the ineptitude of the heat capacity parameter, as DSC results depend on heating/cooling rates. Adequate heat capacity curves were empirically determined, depending on heat transfer rates and based on DSC results and experimental observations. The results of the proposed model

Thermodynamic performance comparison between ORC and Kalina cycles for multi-stream waste heat recovery

International Nuclear Information System (INIS)

Wang, Yufei; Tang, Qikui; Wang, Mengying; Feng, Xiao

2017-01-01

Highlights: • Comparison between ORC and Kalina cycles (KC) for multi-stream waste heat recovery. • Divide waste heat into straight, convex and concave based on its composite curve. • Use heat ratio and temperature of the most point to show the feature of waste heat. • KC is suitable for straight and most concave heat, while ORC for convex one. - Abstract: Organic Rankine cycle (ORC) and Kalina cycle are the main technologies to recover waste heat for power generation. Up to now, many works dealing with the thermodynamic performance comparison between ORC and Kalina cycles are available, but these studies considered for heat recovery from a single heat source or stream. In the process industry, there are multiple waste heat streams, forming a complex heat source profile. In this paper, based on the simulation model developed in the Aspen Hysys software, the two cycles are calculated and compared. According to the waste heat composite curve, the multi-stream waste heat is divided into three kinds, straight, convex, and concave waste heat. Two parameters, the ratio of the heat above and below the most salient/concave point (R) and the temperature of the most point, are used to roughly express the feature of waste heat. With the efficiency from waste heat (exergy) to power as energy performance indicator, the calculation results for waste heat with maximum supply temperature 180 °C show that for straight and concave waste heat with R not less than 0.2, Kalina cycle is better than ORC, while for convex waste heat, ORC is preferable. The work can provide a reference to choose a suitable technology to recover low temperature waste heat for power generation in the process industry.

Survival of parenchymal hepatocytes exposed to 14.3-MeV neutrons

International Nuclear Information System (INIS)

Jirtle, R.L.; Gould, M.N.; DeLuca, P.M. Jr.; Pearson, D.W.

1982-01-01

This report presents the results of the measurement of a dose survival curve and RBE values for rat hepatic cells irradiated in vivo with 14.3 MeV neutrons. The purpose was to determine the RBE for neutrons as a function of dose, and whether hepatocytes exposed to neutrons are as efficient at repairing potentially lethal damage as they are after exposure to low LET radiation

Correlation of heat transfer coefficient in quenching process using ABAQUS

Science.gov (United States)

Davare, Sandeep Kedarnath; Balachandran, G.; Singh, R. K. P.

2018-04-01

During the heat treatment by quenching in a liquid medium the convective heat transfer coefficient plays a crucial role in the extraction of heat. The heat extraction ultimately influences the cooling rate and hence the hardness and mechanical properties. A Finite Element analysis of quenching a simple flat copper sample with different orientation of sample and with different quenchant temperatures were carried out to check and verify the results obtained from the experiments. The heat transfer coefficient (HTC) was calculated from temperature history in a simple flat copper disc sample experimentally. This HTC data was further used as input to simulation software and the cooling curves were back calculated. The results obtained from software and using experimentation shows nearly consistent values.

Genetic Algorithm Design of a 3D Printed Heat Sink

Energy Technology Data Exchange (ETDEWEB)

Wu, Tong [ORNL; Ozpineci, Burak [ORNL; Ayers, Curtis William [ORNL

2016-01-01

In this paper, a genetic algorithm- (GA-) based approach is discussed for designing heat sinks based on total heat generation and dissipation for a pre-specified size andshape. This approach combines random iteration processesand genetic algorithms with finite element analysis (FEA) to design the optimized heat sink. With an approach that prefers survival of the fittest , a more powerful heat sink can bedesigned which can cool power electronics more efficiently. Some of the resulting designs can only be 3D printed due totheir complexity. In addition to describing the methodology, this paper also includes comparisons of different cases to evaluate the performance of the newly designed heat sinkcompared to commercially available heat sinks.

Heat treatment of the EN AC-AlSi9Cu3(Fe alloy

Directory of Open Access Journals (Sweden)

J. Pezda

2010-04-01

Full Text Available Silumins are widely used in automotive, aviation and shipbuilding industries; as having specific gravity nearly three times lower than specific gravity of cast iron the silumins can be characterized by high mechanical properties. Additionally, they feature good casting properties, good machinability and good thermal conductivity. i.e. properties as required for machinery components operating in high temperatures and at considerable loads. Mechanical properties of the silumins can be upgraded, implementing suitably selected heat treatment. In the paper is presented an effect of modification and heat treatment processes on mechanical properties of the EN AC-AlSi9Cu3(Fe alloy. Investigated alloy has undergone typical processes of modification and refining, and next heat treatment. Temperature range of the heat treatment operations was determined on base of curves from the ATD method. Obtained results concern registered melting and solidification curves from the ATD method and strength tests. On base of the performed tests one has determined range of the heat treatment parameters which would assure obtainment of the best possible mechanical properties of the EN AC-AlSi9Cu3(Fe alloy.

Rat mammary-cell survival following irradiation with 14.3-MeV neutrons

International Nuclear Information System (INIS)

Mahler, P.A.; Gould, M.N.; DeLuca, P.M. Jr.; Pearson, D.W.; Clifton, K.H.

1982-01-01

The survival of rat mammary gland cells irradiated in situ with either single or split doses of 14.3-MeV neutrons was determined by an in vivo transplantation assay. The single-dose data are best fit to the multitarget single-hit model by the parameters D 0 = 97 cGy and n = 0.6 while the split-dose data are best fit by the parameters D 0 = 100 cGy and n = 1.2. Analysis of the combined data sets suggests that the two survival curves are not identical. Comparison of these data with previously published results following irradiation with 250-kVp x-rays is reported

Rat mammary cell survival following irradiation with 14.3-MeV neutrons

International Nuclear Information System (INIS)

Mahler, P.A.; Gould, M.N.; DeLuca, P.M. Jr.; Pearson, D.W.; Clifton, K.H.

1982-01-01

The survival of rat mammary gland cells irradiated in situ with either single or split doses of 14.3-MeV neutrons was determined by an in vivo transplantation assay. The single-dose data are best fit to the multitarget single-hit model by the parameters D/sub o/ = 97 cGy and n = 0.6 while the split-dose data are best fit by the parameters D/sub o/ = 100 cGy and n = 1.2.Analysis of the combined data sets suggests that the two survival curves are not identical. Comparison of these data with previously published results following irradiation with 250-kVp X rays is reported

Heat transfer through turbulent boundary layers - The effects of introduction of and recovery from convex curvature

Science.gov (United States)

Simon, T. W.; Moffat, R. J.

1979-01-01

Measurements have been made of the heat transfer through a turbulent boundary layer on a convexly curved isothermal wall and on a flat plate following the curved section. Data were taken for one free-stream velocity and two different ratios of boundary layer thickness to radius of curvature delta/R = 0.051 and delta/R = 0.077. Only small differences were observed in the distribution of heat transfer rates for the two boundary layer thicknesses tested, although differences were noted in the temperature distributions within the boundary layer

Approximation by planar elastic curves

DEFF Research Database (Denmark)

Brander, David; Gravesen, Jens; Nørbjerg, Toke Bjerge

2016-01-01

We give an algorithm for approximating a given plane curve segment by a planar elastic curve. The method depends on an analytic representation of the space of elastic curve segments, together with a geometric method for obtaining a good initial guess for the approximating curve. A gradient......-driven optimization is then used to find the approximating elastic curve....

Experimental and statistical requirements for developing a well-defined K/sub IR/ curve. Final report

International Nuclear Information System (INIS)

Server, W.L.; Oldfield, W.; Wullaert, R.A.

1977-05-01

Further development of a statistically well-defined reference fracture toughness curve to verify and compliment the K/sub IR/ curve presently specified in Appendix G, Section III of the ASME Code was accomplished by performing critical experiments in small specimen fracture mechanics and improving techniques for statistical analysis of the data. Except for cleavage-initiated fracture, crack initiation was observed to occur prior to maximum load for all of the materials investigated. Initiation fracture toughness values (K/sub Jc/) based on R-curve heat-tinting studies were up to 50 percent less than the previously reported equivalent energy values (K*/sub d/). At upper shelf temperatures, the initiation fracture toughness (K/sub Jc/) generally increased with stress intensification rate. Both K/sub Jc/--Charpy V-notch and K/sub Ic/--specimen strength ratio correlations are promising methods for predicting thick-section behavior from small specimens. The previously developed tanh curve fitting procedure was improved to permit estimates of the variances and covariances of the regression coefficients to be computed. The distribution of the fracture toughness data was determined as a function of temperature. Instrumented precracked Charpy results were used to normalize the larger specimen fracture toughness data. The transformed large specimen fracture toughness data are used to generate statistically based lower-bound fracture toughness curves for either static or dynamic test results. A comparison of these lower bound curves with the K/sub IR/ curve shows that the K/sub IR/ curve is more conservative over most of its range. 143 figures, 26 tables

Differences in heat-induced cell killing as determined in three mammalian cell lines do not correspond with the extent of heat radiosensitization

International Nuclear Information System (INIS)

Kampinga, H.H.; Jorritsma, J.B.M.; Burgman, P.; Konings, A.W.T.

1986-01-01

Three different cell lines, Ehrlich ascites tumour (EAT) cells, HeLa S 3 cells and LM mouse fibroblasts, were used to investigate whether or not the extent of heat killing (44 0 C) and heat radio-sensitization (44 0 C before 0-6 Gy X-irradiation) are related. Although HeLa cells were the most heat-resistant cell line and showed the least heat radiosensitization, we found that the most heat-sensitive EAT cells (D 0 , EAT = 8.0 min; D 0 , LM = 10.0 min; D 0 , HeLa = 12.5 min) showed less radiosensitization than the more heat-resistant LM fibroblasts (TERsub(HeLa)< TERsub(EAT)< TERsub(LM)). Therefore, it is concluded that the routes leading to heat-induced cell death are not identical to those determining heat radiosensitization. Furthermore the inactivation of DNA polymerase α and β activities by heat seemed not to correlate with heat survival alone but showed a positive relationship to heat radiosensitization. The possibility of these enzymes being a determinant in heat radiosensitization is discussed. (author)

Respiratory activity as a determinant of radiation survival response

Energy Technology Data Exchange (ETDEWEB)

Bruce, A K; Berner, J D [State Univ. of New York, Buffalo (USA). Dept. of Biology

1976-09-01

Respiration is depressed in irradiated bacteria reaching a minimum level in most strains at 1-3 h after exposure when incubated in growth medium. Since a delay in response is observed, direct action on respiratory enzymes is unlikely. The dosage response of respiration varies widely in the strains studied. All strains exhibit two-component dosage-response curves. The facts suggest that respiration is a major factor in influencing cell survival and may be the principal mechanism through which chemical agents modify radiation response.

Vibrational dynamics and heat capacity of polyglycine I.

Science.gov (United States)

Porwal, Vikas; Misra, Radha Mohan; Tandon, Poonam; Gupta, Vishwambhar Dayal

2004-02-01

Earlier works on polyglycine I suffer from several infirmities, such as the dynamic methylene group being replaced by a mass unit and the use of poorly resolved inelastic neutron spectra, which have resulted in wrong assignments and imprecise profile of dispersion curves. In addition, the density-of-states and heat capacity variation as a function of temperature are being reported for the first time. The heat capacity is in good agreement with the measurements reported earlier by Roles and Wunderlich within a certain range (230-350 K). Deviations set in beyond this could be due to the presence of two crystalline states (I and II) in the sample used for the heat capacity measurements.

The mechanism of heat transfer in transition boiling

International Nuclear Information System (INIS)

Chin Pan; Hwang, J.Y.; Lin, T.L.

1989-01-01

Liquid-solid contact in transition boiling is modelled by involving transient conduction, boiling incipience, macrolayer evaporation and vapour film boiling. The prediction of liquid contact duration and time fraction agrees reasonably well with experimental data, and the model is able to predict both of the boiling curve transitions - the critical and minimum heat fluxes. The study concludes that the liquid turbulence due to buoyancy forces and bubble agitation is an important parameter for transition boiling. It is found that surface coating (oxidation or deposition) tends to improve the transition boiling heat transfer and elevate the wall superheats at both the critical heat flux and the minimum film boiling points, which agrees with the experimental observations. (author)

Bragg Curve Spectroscopy

International Nuclear Information System (INIS)

Gruhn, C.R.

1981-05-01

An alternative utilization is presented for the gaseous ionization chamber in the detection of energetic heavy ions, which is called Bragg Curve Spectroscopy (BCS). Conceptually, BCS involves using the maximum data available from the Bragg curve of the stopping heavy ion (HI) for purposes of identifying the particle and measuring its energy. A detector has been designed that measures the Bragg curve with high precision. From the Bragg curve the range from the length of the track, the total energy from the integral of the specific ionization over the track, the dE/dx from the specific ionization at the beginning of the track, and the Bragg peak from the maximum of the specific ionization of the HI are determined. This last signal measures the atomic number, Z, of the HI unambiguously

Injury risk curves for the WorldSID 50th male dummy.

Science.gov (United States)

Petitjean, Audrey; Trosseille, Xavier; Petit, Philippe; Irwin, Annette; Hassan, Joe; Praxl, Norbert

2009-11-01

logistic regression, the survival analysis and the Consistent Threshold Estimate. The paper presents the methods used to check and process the data, select the PMHS tests, and construct the injury risk curves. The PMHS dataset as well as the injury risk curves are provided.

Effect of heat treatment operations on the Rm tensile strength of silumins

Directory of Open Access Journals (Sweden)

J. Pezda

2010-10-01

Full Text Available Owing to good technological properties, low weight and good corrosion resistance, aluminum-silicon alloys are widely used as a material for cast machinery components. State of macro- and microstructure of a castings manufactured from Al-Si alloys, which is determined by a shape and distribution of hardening phases, segregation of alloying constituents and impurities, as well as distribution of porosity, create conditions to obtainment of proper mechanical properties. These properties can be improved through modification of the alloy and performed heat treatment operations. The paper presents effect of modification and heat treatment process on the Rm tensile strength of a selected silumins (EN AB-AlSi9Cu3(Fe, EN AB-AlSi12CuNiMg, EN AB-AlSi17Cu1Ni1Mg. Investigated alloys were put to treatments of refining and modification, and next to heat treatment. Temperature range of the heat treatment operations was determined on base of curves from the ATD method. Obtained results illustrate registered curves of melting and solidification from the ATD method and strength tests. On base of performed initial tests one determined parameters of the heat treatment process (temperature and duration of solutionig and ageing treatments enabling obtainment of improved Rm tensile strength of the investigated alloys.

Learning Curve? Which One?

Directory of Open Access Journals (Sweden)

Paulo Prochno

2004-07-01

Full Text Available Learning curves have been studied for a long time. These studies provided strong support to the hypothesis that, as organizations produce more of a product, unit costs of production decrease at a decreasing rate (see Argote, 1999 for a comprehensive review of learning curve studies. But the organizational mechanisms that lead to these results are still underexplored. We know some drivers of learning curves (ADLER; CLARK, 1991; LAPRE et al., 2000, but we still lack a more detailed view of the organizational processes behind those curves. Through an ethnographic study, I bring a comprehensive account of the first year of operations of a new automotive plant, describing what was taking place on in the assembly area during the most relevant shifts of the learning curve. The emphasis is then on how learning occurs in that setting. My analysis suggests that the overall learning curve is in fact the result of an integration process that puts together several individual ongoing learning curves in different areas throughout the organization. In the end, I propose a model to understand the evolution of these learning processes and their supporting organizational mechanisms.

Linking pinch analysis and bridge analysis to save energy by heat-exchanger network retrofit

International Nuclear Information System (INIS)

Bonhivers, Jean-Christophe; Moussavi, Alireza; Alva-Argaez, Alberto; Stuart, Paul R.

2016-01-01

Highlights: • The flow rate of cascaded heat in exchangers is presented between composite curves. • Reducing energy consumption implies decreasing the flow rate of cascaded heat. • Removing cross-pinch transfers is not necessary to reduce energy consumption. • Bridge modifications are necessary to reduce energy consumption. • Bridge modifications are evaluated on the Heat Exchanger Load Diagram. - Abstract: Reduction of energy requirements in the process industries results in increased profitability and better environmental performance. Methods for heat exchanger network (HEN) retrofit are based on thermodynamic analysis and insights, numerical optimization, or combined approaches. Numerical optimization-based methods are highly complex and may not guarantee identification of the global optimum. Pinch analysis, which is an approach based on thermodynamic analysis and composite curves, is the most widely used in the industry. Its simplicity, the use of graphical tools, and the possibility for the user to interact at each step of the design process help identify solutions with consideration of practical feasibility. In the last few years, bridge analysis has been developed for HEN retrofit. It includes the following tools: (a) the definition of the necessary conditions to reduce energy consumption which are expressed in the bridge formulation, (b) a method for enumerating the bridges, (c) the representation of the flow rate of cascaded heat through each existing exchanger on the energy transfer diagram (ETD), and (4) the use of the Heat Exchanger Load Diagram (HELD) to identify a suitable HEN configuration corresponding to modifications. It has been shown that reducing energy consumption implies decreasing the flow rate of cascaded heat through the existing exchangers across the entire temperature range between the hot and cold utilities. The ETD shows all possibilities to reduce the flow rate of cascaded heat through a HEN. The objective of this paper is

Contractibility of curves

Directory of Open Access Journals (Sweden)

Janusz Charatonik

1991-11-01

Full Text Available Results concerning contractibility of curves (equivalently: of dendroids are collected and discussed in the paper. Interrelations tetween various conditions which are either sufficient or necessary for a curve to be contractible are studied.

Modelling the phase curve and occultation of WASP-43b with SPIDERMAN

Science.gov (United States)

Louden, Tom

2017-06-01

Presenting SPIDERMAN, a fast code for calculating exoplanet phase curves and secondary eclipses with arbitrary two dimensional surface brightness distributions. SPIDERMAN uses an exact geometric algorithm to calculate the area of sub-regions of the planet that are occulted by the star, with no loss in numerical precision. The speed of this calculation makes it possible to run MCMCs to marginalise effectively over the underlying parameters controlling the brightness distribution of exoplanets. The code is fully open source and available over Github. We apply the code to the phase curve of WASP-43b using an analytical surface brightness distribution, and find an excellent fit to the data. We are able to place direct constraints on the physics of heat transport in the atmosphere, such as the ratio between advective and radiative timescales at different altitudes.

Roc curves for continuous data

CERN Document Server

Krzanowski, Wojtek J

2009-01-01

Since ROC curves have become ubiquitous in many application areas, the various advances have been scattered across disparate articles and texts. ROC Curves for Continuous Data is the first book solely devoted to the subject, bringing together all the relevant material to provide a clear understanding of how to analyze ROC curves.The fundamental theory of ROC curvesThe book first discusses the relationship between the ROC curve and numerous performance measures and then extends the theory into practice by describing how ROC curves are estimated. Further building on the theory, the authors prese

Containerless Heating Process of a Deeply Undercooled Metal Droplet by Electrostatic Levitation

International Nuclear Information System (INIS)

Wang Fei-Long; Dai Bin; Liu Xue-Feng; Sun Yi-Ning; Sun Zhi-Bin; Yu Qiang; Zhai Guang-Jie

2015-01-01

We present the containerless heating process of a deeply undercooled metal droplet by electrostatic levitation. The problem of surface charge loss in the heating process is discussed and specific formulas are given to describe the basic process of charge supplement by the photoelectric and thermoelectric effects. The pure metal zirconium is used to be melted and solidified to analyze the heating process. The temperature-time curve clearly shows the features including melting, undercooling, recalescence and solid-state phase transformation. (paper)

Prognostic and survival analysis of 837 Chinese colorectal cancer patients.

Science.gov (United States)

Yuan, Ying; Li, Mo-Dan; Hu, Han-Guang; Dong, Cai-Xia; Chen, Jia-Qi; Li, Xiao-Fen; Li, Jing-Jing; Shen, Hong

2013-05-07

To develop a prognostic model to predict survival of patients with colorectal cancer (CRC). Survival data of 837 CRC patients undergoing surgery between 1996 and 2006 were collected and analyzed by univariate analysis and Cox proportional hazard regression model to reveal the prognostic factors for CRC. All data were recorded using a standard data form and analyzed using SPSS version 18.0 (SPSS, Chicago, IL, United States). Survival curves were calculated by the Kaplan-Meier method. The log rank test was used to assess differences in survival. Univariate hazard ratios and significant and independent predictors of disease-specific survival and were identified by Cox proportional hazard analysis. The stepwise procedure was set to a threshold of 0.05. Statistical significance was defined as P analysis suggested age, preoperative obstruction, serum carcinoembryonic antigen level at diagnosis, status of resection, tumor size, histological grade, pathological type, lymphovascular invasion, invasion of adjacent organs, and tumor node metastasis (TNM) staging were positive prognostic factors (P analysis showed a significant statistical difference in 3-year survival among these groups: LNR1, 73%; LNR2, 55%; and LNR3, 42% (P analysis results showed that histological grade, depth of bowel wall invasion, and number of metastatic lymph nodes were the most important prognostic factors for CRC if we did not consider the interaction of the TNM staging system (P < 0.05). When the TNM staging was taken into account, histological grade lost its statistical significance, while the specific TNM staging system showed a statistically significant difference (P < 0.0001). The overall survival of CRC patients has improved between 1996 and 2006. LNR is a powerful factor for estimating the survival of stage III CRC patients.

Chordoma: review of clinico radiological features and factors affecting survival

International Nuclear Information System (INIS)

Soo, M.Y.S.

2001-01-01

This study reviews the clinico radiological features of cranial and sacrospinal chordomas and identifies factors affecting survival. Nineteen patients seen between January 1980 and December 2000 with histopathological diagnosis of chordomas were retrospectively reviewed with reference to clinical presentation, imaging features, treatment modalities and post-therapy status. Eight had tumours in the skull base while 11 patients had spinal and sacro-coccygeal lesions. Surgical resection was performed in 16 patients whose subsequent natural history was used to identify clinical indicators that may influence survival. Completeness of resection, age, gender and postoperative irradiation were subjected to analysis using the Cox proportional hazard models. Kaplan-Meir survival curves illustrate the survival distributions. Diplopia and facial pain are prime clinical presentations in cranial lesions, while extremity weakness and a sacrogluteal mass are common complaints in the sacrospinal group. Lesional calcifications are present in 40% while an osteolytic soft tissue mass is detectable by CT in all cases. Heterogeneous signals and internal septations on T 2 -weighted MRI are predominant features. In sacrospinal tumours, complete excision with adjuvant radiotherapy achieves the best results with a disease-free survival of more than 5 years. The clinical and imaging findings in this study are in accordance with those of other series. Except for complete surgical excision followed by radiotherapy in the subset of patients with sacrospinal tumours, none of the other clinical indicators show a statistical significant influence on survival. Copyright (2001) Blackwell Science Pty Ltd

Thermal control system. [removing waste heat from industrial process spacecraft

Science.gov (United States)

Hewitt, D. R. (Inventor)

1983-01-01

The temperature of an exothermic process plant carried aboard an Earth orbiting spacecraft is regulated using a number of curved radiator panels accurately positioned in a circular arrangement to form an open receptacle. A module containing the process is insertable into the receptacle. Heat exchangers having broad exterior surfaces extending axially above the circumference of the module fit within arcuate spacings between adjacent radiator panels. Banks of variable conductance heat pipes partially embedded within and thermally coupled to the radiator panels extend across the spacings and are thermally coupled to broad exterior surfaces of the heat exchangers by flanges. Temperature sensors monitor the temperature of process fluid flowing from the module through the heat exchanges. Thermal conduction between the heat exchangers and the radiator panels is regulated by heating a control fluid within the heat pipes to vary the effective thermal length of the heat pipes in inverse proportion to changes in the temperature of the process fluid.

An axisymmetrical non-linear finite element model for induction heating in injection molding tools

DEFF Research Database (Denmark)

Guerrier, Patrick; Nielsen, Kaspar Kirstein; Menotti, Stefano

2016-01-01

To analyze the heating and cooling phase of an induction heated injection molding tool accurately, the temperature dependent magnetic properties, namely the non-linear B-H curves, need to be accounted for in an induction heating simulation. Hence, a finite element model has been developed......, including the non-linear temperature dependent magnetic data described by a three-parameter modified Frohlich equation fitted to the magnetic saturation curve, and solved with an iterative procedure. The numerical calculations are compared with experiments conducted with two types of induction coils, built...... in to the injection molding tool. The model shows very good agreement with the experimental temperature measurements. It is also shown that the non-linearity can be used without the temperature dependency in some cases, and a proposed method is presented of how to estimate an effective linear permeability to use...

Injury risk curves for the skeletal knee-thigh-hip complex for knee-impact loading.

Science.gov (United States)

Rupp, Jonathan D; Flannagan, Carol A C; Kuppa, Shashi M

2010-01-01

Injury risk curves for the skeletal knee-thigh-hip (KTH) relate peak force applied to the anterior aspect of the flexed knee, the primary source of KTH injury in frontal motor-vehicle crashes, to the probability of skeletal KTH injury. Previous KTH injury risk curves have been developed from analyses of peak knee-impact force data from studies where knees of whole cadavers were impacted. However, these risk curves either neglect the effects of occupant gender, stature, and mass on KTH fracture force, or account for them using scaling factors derived from dimensional analysis without empirical support. A large amount of experimental data on the knee-impact forces associated with KTH fracture are now available, making it possible to estimate the effects of subject characteristics on skeletal KTH injury risk by statistically analyzing empirical data. Eleven studies were identified in the biomechanical literature in which the flexed knees of whole cadavers were impacted. From these, peak knee-impact force data and the associated subject characteristics were reanalyzed using survival analysis with a lognormal distribution. Results of this analysis indicate that the relationship between peak knee-impact force and the probability of KTH fracture is a function of age, total body mass, and whether the surface that loads the knee is rigid. Comparisons between injury risk curves for the midsize adult male and small adult female crash test dummies defined in previous studies and new risk curves for these sizes of occupants developed in this study suggest that previous injury risk curves generally overestimate the likelihood of KTH fracture at a given peak knee-impact force. Future work should focus on defining the relationships between impact force at the human knee and peak axial compressive forces measured by load cells in the crash test dummy KTH complex so that these new risk curves can be used with ATDs.

Prospects of engineering thermotolerance in crops through modulation of heat stress transcription factor and heat shock protein networks.

Science.gov (United States)

Fragkostefanakis, Sotirios; Röth, Sascha; Schleiff, Enrico; Scharf, Klaus-Dieter

2015-09-01

Cell survival under high temperature conditions involves the activation of heat stress response (HSR), which in principle is highly conserved among different organisms, but shows remarkable complexity and unique features in plant systems. The transcriptional reprogramming at higher temperatures is controlled by the activity of the heat stress transcription factors (Hsfs). Hsfs allow the transcriptional activation of HSR genes, among which heat shock proteins (Hsps) are best characterized. Hsps belong to multigene families encoding for molecular chaperones involved in various processes including maintenance of protein homeostasis as a requisite for optimal development and survival under stress conditions. Hsfs form complex networks to activate downstream responses, but are concomitantly subjected to cell-type-dependent feedback regulation through factor-specific physical and functional interactions with chaperones belonging to Hsp90, Hsp70 and small Hsp families. There is increasing evidence that the originally assumed specialized function of Hsf/chaperone networks in the HSR turns out to be a complex central stress response system that is involved in the regulation of a broad variety of other stress responses and may also have substantial impact on various developmental processes. Understanding in detail the function of such regulatory networks is prerequisite for sustained improvement of thermotolerance in important agricultural crops. © 2014 John Wiley & Sons Ltd.

Atlas of stress-strain curves

CERN Document Server

2002-01-01

The Atlas of Stress-Strain Curves, Second Edition is substantially bigger in page dimensions, number of pages, and total number of curves than the previous edition. It contains over 1,400 curves, almost three times as many as in the 1987 edition. The curves are normalized in appearance to aid making comparisons among materials. All diagrams include metric (SI) units, and many also include U.S. customary units. All curves are captioned in a consistent format with valuable information including (as available) standard designation, the primary source of the curve, mechanical properties (including hardening exponent and strength coefficient), condition of sample, strain rate, test temperature, and alloy composition. Curve types include monotonic and cyclic stress-strain, isochronous stress-strain, and tangent modulus. Curves are logically arranged and indexed for fast retrieval of information. The book also includes an introduction that provides background information on methods of stress-strain determination, on...

Physiochemical properties, microstructure, and probiotic survivability of nonfat goats' milk yogurt using heat-treated whey protein concentrate as fat replacer.

Science.gov (United States)

Zhang, Tiehua; McCarthy, James; Wang, Guorong; Liu, Yanyan; Guo, Mingruo

2015-04-01

There is a market demand for nonfat fermented goats' milk products. A nonfat goats' milk yogurt containing probiotics (Lactobacillus acidophilus, and Bifidobacterium spp.) was developed using heat-treated whey protein concentrate (HWPC) as a fat replacer and pectin as a thickening agent. Yogurts containing untreated whey protein concentrate (WPC) and pectin, and the one with only pectin were also prepared. Skim cows' milk yogurt with pectin was also made as a control. The yogurts were analyzed for chemical composition, water holding capacity (syneresis), microstructure, changes in pH and viscosity, mold, yeast and coliform counts, and probiotic survivability during storage at 4 °C for 10 wk. The results showed that the nonfat goats' milk yogurt made with 1.2% HWPC (WPC solution heated at 85 °C for 30 min at pH 8.5) and 0.35% pectin had significantly higher viscosity (P yogurts and lower syneresis than the goats' yogurt with only pectin (P yogurt samples did not change much throughout storage. Bifidobacterium spp. remained stable and was above 10(6) CFU g(-1) during the 10-wk storage. However, the population of Lactobacillus acidophilus dropped to below 10(6) CFU g(-1) after 2 wk of storage. Microstructure analysis of the nonfat goats' milk yogurt by scanning electron microscopy revealed that HWPC interacted with casein micelles to form a relatively compact network in the yogurt gel. The results indicated that HWPC could be used as a fat replacer for improving the consistency of nonfat goats' milk yogurt and other similar products. © 2015 Institute of Food Technologists®

Study on critical heat flux based on wavelet transform in rectangular narrow channels

International Nuclear Information System (INIS)

Zhou Tao; Ju Zhongyun; Zhang Lei; Li Jingjing; Sheng Cheng; Xiao Zejun

2014-01-01

Critical heat flux is very important for nuclear reactor safety, and observing temperature rise rate is a feasible method. Through using the wavelet transform to analyze the CHF temperature rise curves in rectangular narrow channels, it can remove relative weaker interference and effectively judge CHF. Rectangular narrow channel can strengthen heat transfer and reduce CHF, whose characteristics are proved by, temperature rise curves analyzed by wavelet transform. Respectively applying Daubechies function and Haar function is for guarantee the accuracy of the wavelet analysis, and Daubechies function is more accurate than Haar function in the detail signal processing from results. While the wavelet analysis and experimental results are compared and found in good agreement with the experimental results. (authors)

Effect of storage temperatures and stresses on the survival of Salmonella spp. in halva.

Science.gov (United States)

Osaili, T M; Al-Nabulsi, A A; Nazzal, D S; Shaker, R R

2017-11-01

The presence of Salmonella spp. in halva has been associated with foodborne illnesses and product recalls from the markets. This study investigated the effect of environmental stresses on the survival of Salmonella spp. in halva during storage for 12 months at 10 and 25°C (log (N 0 /N) g -1 ). Halva samples were inoculated with a cocktail of four strains of unstressed, desiccation stressed or heat stressed Salmonella (10 6 -10 7  CFU per gram). In general, survival of Salmonella spp. in halva decreased significantly (P ˂ 0·05) as storage time and temperature increased. At the end of halva shelf life at 10°C, the initial populations of unstressed, desiccation stressed or heat stressed Salmonella spp. decreased by 2·7, 2·6 or 2·8 log CFU per gram (reduction rate c. 0·2 log CFU per month), respectively. While at 25°C, the populations decreased 5·2, 6·7 or 6·3 log CFU per gram, respectively (reduction rate c. 0·4-0·5 log CFU per month). The populations of stressed Salmonella spp. in halva samples were not significantly different (P ≥ 0·05) from populations of unstressed cells during storage at 10 and 25°C, except during the last 3 months of storage at 25°C when populations of unstressed cells were higher (P Salmonella spp. to desiccation or heat stress prior product contamination may play a role in Salmonella spp. survival in halva during storage. Contamination of halva (tahini halva) with Salmonella from raw materials or during production was documented. Halva and tahini have been involved in salmonellosis outbreaks in different countries. The study demonstrated enhanced survivability of stressed and unstressed Salmonella spp. in halva over a 12-month storage period at 10 and 25°C with lower log reductions than expected. Exposing Salmonella spp. to desiccation or heat stress prior product contamination may play a role in microbial survival in halva during storage. These findings serve as a model to halva producers to implement control

Magnetic response of certain curved graphitic geometries

International Nuclear Information System (INIS)

Wang, L.; Davids, P.S.; Saxena, A.; Bishop, A.R.

1992-01-01

The quasi-particle energy spectra associated with some members of buckyfamily (curved graphitic geometries), in particular C 50 , C 60 , C 70 and related fullerenes as well as coaxial helical microtubules of graphite, are obtained analytically within the mean-field approximation. These energy spectra are then used to calculate various response functions. Specifically, we calculate the specific heat, magnetization and magnetic susceptibility in the presence of an external magnetic field at low temperatures. For a single microtubule an extra peak superimposed on the first de Haas van Alphen (dHvA) oscillation in magnetic susceptibility is found in the 50--170 Tesla range depending on the radius which is possibly accessible in special (explosive flux compression) experiments. Finally, we point to important potential applications of these novel mesoscopic structures in nanotechnology

Tornado-Shaped Curves

Science.gov (United States)

Martínez, Sol Sáez; de la Rosa, Félix Martínez; Rojas, Sergio

2017-01-01

In Advanced Calculus, our students wonder if it is possible to graphically represent a tornado by means of a three-dimensional curve. In this paper, we show it is possible by providing the parametric equations of such tornado-shaped curves.

Effect of pre-irradiation on thermal inactivation of B. pumilus E 601 dry spores irradiated with EB and. gamma. -rays

Energy Technology Data Exchange (ETDEWEB)

Watanabe, Yuhei; Ito, Hitoshi; Ishigaki, Isao [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

1989-11-01

The survival fraction of B. pumilus spores irradiated with {gamma} -rays and electron beams in vacuum were increased when the spores were heated or allowed to stand in vacuum for a long time at room temperature. The survival curves of the spores thus treated after irradiation might give apparent radiation sensitivities which were lower than true ones obtained just after irradiation. On the contrary, the radiation sensitivities of the spores irradiated in dry air and then heated or allowed to stand in dry air became high. To elucidate the characteristics of th spores, the effect of heating on the radiation sensitivity of the B. pumilus spores has been studied. By heating the pre-irradiated spores in vacuum, its survival fraction was increased, in other words, the spores inactivated with radiation were recovered. However, the thermal sensitivity of the recovered spores was found to be high compared with that of the original spores. On the other hand, when B. pumilus spores were irradiated in dry air and then heated in dry air, the survival curves of the spores were found to be composed of two exponential curves, suggesting that two kinds of thermal inactivation mechanism existed. From Arrhenius plots of unirradiated B. pumilus spores, the activation energies of the thermal inactivation in the range of 90degC to 120degC in vacuum and in air were found to be about 38 kcal/mol and 29 kcal/mol, respectively. The activation energy of the spores at a temperature of higher than 120degC, however increased to give the same value (about 38 kcal/mol) as found in vacuum. This fact suggests the main mechanism of the thermal inactivation of the spores varies near 120degC. Arrhenius plots of irradiated spores in vacuum was similar to that of unirradiated ones. Thermal inactivation rates of the irradiated spores in the presence of air will also be discussed as compared with those of unirradiated ones. (author).

Effect of millimeter waves on survival of UVC-exposed Escherichia coli

International Nuclear Information System (INIS)

Rojavin, M.A.; Ziskin, M.C.

1995-01-01

Bacterial cells of the strain Escherichia coli K12 were exposed to millimeter electromagnetic waves (mm waves) with and without additional exposure to ultraviolet light λ = 254 nm (UVC). The mm waves were produced by a medical microwave generator emitting a 4-GHz-wide band around a 61 GHz center frequency and delivering an irradiation of 1mW/cm 2 and a standard absorption rate (SAR) of 84 W/kg to the bacteria. Exposure to the mm waves alone for up to 30 minutes did not change the survival rate of bacteria. Exposure to mm waves followed by UVC irradiation also did not alter the number of surviving E. coli cells in comparison to UVC-treated controls. When mm waves were applied after the UVC exposure, a dose-dependent increase of up to 30% in the survival of E. coli was observed compared to UVC + sham-irradiated bacteria. Because sham controls and experimental samples were maintained under the same thermal conditions, the effect is not likely to be due to heating, although the possibility of nonuniform distribution of microwave heating in different layers of irradiated bacterial suspension cannot be ruled out. The mechanism for this effect appears to involve certain DNA repair systems that act as cellular targets for mm waves

A study on the jet pump characteristic curve in boiling water reactor

International Nuclear Information System (INIS)

Liao, L.Y.

1990-01-01

The jet pump models of RELAP5/MOD2, RETRAN-02/MOD3, and RELAP4/MOD3 are compared. From the investigation of the momentum equations, it is found that the normal quadrant jet pump models of these codes are essentially the same. In this paper, it is found that the relationship between the flow ratio, M, and the heat ratio, N, is uniquely determined for a given jet pump geometry provided that the wall friction and gravitational head are neglected. In other words, under the given assumptions the M - N characteristic curve will not change with power level, recirculation pump speed and loop flow rate. The effect of the gravitational head on the M - N curve has been found to be significant for low flow conditions. As a result, a guideline has been given to the definition of the specific energy (or the head ratio). Sensitivity studies on the key parameters have been performed. It is found that the generic M - N curve should not be used for a jet pump which does not have the same nozzle to throat area ratio as that of the generic jet pump

A versatile curve-fit model for linear to deeply concave rank abundance curves

NARCIS (Netherlands)

Neuteboom, J.H.; Struik, P.C.

2005-01-01

A new, flexible curve-fit model for linear to concave rank abundance curves was conceptualized and validated using observational data. The model links the geometric-series model and log-series model and can also fit deeply concave rank abundance curves. The model is based ¿ in an unconventional way

Survival and DNA repair in ultraviolet-irradiated haploid and diploid cultured frog cells