Improvements on heap leaching process for a refractory uranium ore and yellow cake precipitation process

International Nuclear Information System (INIS)

Feng Jianke

2013-01-01

Some problems such as formed harden matrix, ore heap compaction, poor permeability, and agglomeration of absorption resin occur during extracting uranium from a refractory uranium ore by heap leaching process. After some measures were taken, i.e. spraying a new ore heap by low concentration acid, two or more ore heaps in series leaching, turning ores in ore heap, the permeability was improved, acid consumption was reduced. Through precipitate circulation and aging, the yellow cake slurry in amorphous or microlite form was transformed to crystal precipitate, thus uranium content in yellow cake was improved, and water content in yellow cake was lowered with good economic benefits. (author)

Role of hydrogen ions in standard and activation heap leaching of gold

Science.gov (United States)

Rubtsov, YuI

2017-02-01

The role of hydrogen ions in activation heap leaching of gold from rebellious ore has been studied, which has allowed enhancing gold recovery. The author puts forward a gold leaching circuit with the use of activated oxygen-saturated solutions acidified to pH = 6-9.

Heap leach cyanide irrigation and risk to wildlife: Ramifications for the international cyanide management code.

Science.gov (United States)

Donato, D B; Madden-Hallett, D M; Smith, G B; Gursansky, W

2017-06-01

Exposed cyanide-bearing solutions associated with gold and silver recovery processes in the mining industry pose a risk to wildlife that interact with these solutions. This has been documented with cyanide-bearing tailings storage facilities, however risks associated with heap leach facilities are poorly documented, monitored and audited. Gold and silver leaching heap leach facilities use cyanide, pH-stabilised, at concentrations deemed toxic to wildlife. Their design and management are known to result in exposed cyanide-bearing solutions that are accessible to and present a risk to wildlife. Monitoring of the presence of exposed solutions, wildlife interaction, interpretation of risks and associated wildlife deaths are poorly documented. This paper provides a list of critical monitoring criteria and attempts to predict wildlife guilds most at risk. Understanding the significance of risks to wildlife from exposed cyanide solutions is complex, involving seasonality, relative position of ponding, temporal nature of ponding, solution palatability, environmental conditions, in situ wildlife species inventory and provision of alternative drinking sources for wildlife. Although a number of heap leach operations are certified as complaint with the International Cyanide Management Code (Cyanide Code), these criteria are not considered by auditors nor has systematic monitoring regime data been published. Without systematic monitoring and further knowledge, wildlife deaths on heap leach facilities are likely to remain largely unrecorded. This has ramifications for those operations certified as compliance with the Cyanide Code. Copyright © 2017 Elsevier Inc. All rights reserved.

Heap-leaching of low-grade uranium ore at SOMAIR: from laboratory tests to production of 700 tonnes U per year

Energy Technology Data Exchange (ETDEWEB)

Durupt, N.; Blanvillain, J.J., E-mail: nicolas.durupt@areva.com [AREVA NC, Service d' Etudes de Procedes et d' Analyses (SEPA), Bessines sur Gartempe (France)

2010-07-01

In 2006, SOMAIR decided to increase the uranium production by 50% using heap leaching for the treatment of low grade ores. These ores, which come from different ores with various properties, have been studied in four steps: Lab tests: to compare the ores (characterization, acid consumptions, recovery); Column tests on an average sample: to define significant parameters for a feasibility study; Column tests on specific samples: to optimize recovery for each ore and identify problems of percolation due to the clays; and, Pilot tests in large boxes (stalls): to validate process parameters. Uranium production by heap leaching started commercially in July 2009. (author)

Use of low-cost heat sources to improve the efficiency of heap leaching of uranium ores. Part of a coordinated programme on bacterial leaching of uranium ores

International Nuclear Information System (INIS)

Ajuria, S.

1977-12-01

Basic technical parameters are given of two solar heaters designed for use in heap leaching of uranium ores. Inexpensive and easily available materials such as flat glass panes, glass tubing and corrugated metal sheets were used in the construction of the heaters. Under optimum conditions, the heaters can produce temperature differentials of 52 0 C (50 0 C) at the flow rate of 30ml/min. The dependence of percent recovery on the temperature of solutions in heap leaching of ore from 'El Nopal' was studied. Even though no precise correlation was found, an increase in the temperature of solutions seems to improve the efficiency of heap leaching

Development of the heap leaching of low-grade uranium ores for conditions of OJSC Priargunsky Mining and Chemical plant (PPGKhO)

International Nuclear Information System (INIS)

Morozov, A.; Litvinenko, V.

2014-01-01

The treatment of low-grade commercial uranium ores by heap leaching has been carried out at the enterprise since 1996. During the initial stage of development, the ore piles were formed of the raw ore having the run-of-mine coarseness with uranium content around 0.08%. Under such conditions, recovery of the metal to the solution is 60-65% in case of a pile treatment lasting 2 years. To intensify the process and to provide a stable concentration of uranium in the productive solutions transferred to sorption, the enterprise developed and implemented a method of percolation leaching of low-grade ores with re-circulation of productive solutions through the re-treated ore bulk (RF patent No. 2226564). The main peculiarity of such leaching is simultaneous moistening of the ore by productive solutions and by barren solutions that are sharpened with sulphuric acid; that gives the possibility to wet far bigger areas of piles under constant volume of productive solutions outputting to the sorption treatment. Such scheme enables to treat successively first the piles at the “re-treatment” (where the metal is mainly extracted), and then the piles at the “active leaching” stage (where the metal is mainly inside the ore bulk). The technical and economic indexes of the heap leaching of low-grade uranium ores were significantly increased in 2006, when the X-ray-radiometric treatment plant was commissioned. The technological scheme of ore treatment at the processing plant includes mould and grating of the raw material with delivery of undersized products enriched with uranium: -5 mm are transferred to the pulp process; fractions (-200+40) mm to the X-ray-radiometric separation; the material of size (-40+5) mm, washed-out from clayey and fine particles, are sent to the uranium heap leaching in piles. Delivery of the ore material having size (-40+5) mm to treatment by the acid leaching method excluded colmatage and creation of zones impermeable for water, and in combination

An analysis of the heap construction by long hole blasting for in-situ leaching of blasted ore

International Nuclear Information System (INIS)

Yang Shijiao

1999-01-01

The author establishes specific requirements for heap construction by blasting on the basis of the mechanism for in situ leaching of blasted ore, analyses the feasibility of heap construction by long hole blasting, selection of the blast plan and the relevant technological problems, and gives a case of heap construction by long hole blasting in Renhua uranium mine

Heap leaching of Cu contaminated soil with [S,S]-EDDS in a closed process loop

International Nuclear Information System (INIS)

Finzgar, Neza; Zumer, Alenka; Lestan, Domen

2006-01-01

Heap leaching of Cu contaminated soil (412 ± 11 mg kg -1 ) with 5 mmol kg -1 ethylenediamine disuccinate [S,S]-EDDS as a chelator was tested in a laboratory-scale soil column study. The washing solution was recycled in a closed process loop after microbial (using a microbially active permeable bed, composed of substrate and absorbent) and oxidative chemical (using combined ozonation and UV irradiation) degradation of metal-[S,S]-EDDS complexes and retention of released Cu on a commercial absorbent Slovakite. Heap leaching using the permeable bed removed 25.5 ± 3.6% of initial total Cu from the soil. Ozone/UV treatment of the [S,S]-EDDS washing solution removed much more, 47.5 ± 7.4%, of Cu. Both methods yielded a clear and colorless final (waste) washing solution, with 7.0 ± 10.0 and 2.6 ± 0.7 mg L -1 Cu (permeable bed and ozone/UV method, respectively). The results of our study indicate that chemical treatment of chelator washing solution with ozone/UV in a closed process loop could lead to the development of a new, efficient and environmentally safe remediation method with controllable Cu emissions

Taoshan uranium ore fields in situ blasting heap leaching rate influence factors to investigate

International Nuclear Information System (INIS)

Xie Wangnan; Dong Chunming

2014-01-01

Taoshan ore field ore in situ blasting heap leaching out build industrial test and production process, stope leaching rate and leaching cycle is large than that, after analysis, blasting method and cloth liquid way is to affect leaching rate and leaching cycle of the main factors. This paper holds that as far as possible using stratified deep hole blasting of squeezing up ways to reduce the building pile of in-situ leaching ore block rate; Adopting effective cloth tube way, increase the leaching agent and ore contact comprehensive; Introduction of bacterial leaching, and other means to improve leaching rate, shorten production cycle, etc to solve it. (authors)

Study On The Choice Of Leaching System For Thanh My, Quang Nam Province Uranium Ores Treatment

International Nuclear Information System (INIS)

Than Van Lien; Nguyen Dinh Van; Tran The Dinh

2011-01-01

In order to implement the plan of peaceful uses of atomic energy, the Radioactive and Rare Earth Geology Division have been carried out the uranium ores exploitation project in Thanh My area of Quang Nam province since 2010. The treatment uranium ores samples is one of works of this project. In order to preparing for uranium ores samples treatment, the Institute for Technology of Radioactive and Rare Elements have been studied and have chosen the heap leaching method for Thanh My uranium ore treatment. The ore, which contained less than 0.07% U, was crushed to -1 cm before being placed in the heap. The acid consumption for this heap leach operation was approximately ranged 40 kg - 45 kg of H 2 SO 4 per tonne of ore, and oxidant 4 kg of MnO 2 per tonne of ore. The entire treatment cycle required 20-25 days, the recovery exceeded 80%, the leached tails contained less than 0.01% U. The experimental results were comparable with those obtained in the field scale heap leaching in the world. (author)

Building a Uranium Heap Leach Project

International Nuclear Information System (INIS)

Schnell, Henry

2014-01-01

Despite all these we have seen many HL successes and many interesting projects coming down the pipe. • Previous experience in Uranium with previous ROM projects in France (Bessines, Langone), Niger (Somair), Canada (Agnew Lake) and other locations had provided some basic background. • Heap leach based on copper experience with crushed ore has operated for many years in Brazil (Caetite). • Many gold operations for many decades in all climates and continents. • Copper at +20% of production, many in Chile, but also now in many other countries. • Uranium with agglomerated crushed ores is now becoming more prominent – Somair, Imouraren, Trekkopje. • Work also ongoing for Ranger, Rossing, and in consideration for other projects. • Other notable work in Nickel, and multi-metal such as Talvivaara

Uraniferous minerals heap leaching process by counter techique

International Nuclear Information System (INIS)

Fuentes G, D.A.

1978-01-01

An experimental study was made at laboratory level with respect to a process for the treatment of an uranium ore by counter current acid heap leaching with maturity periods and washing. This mineral with an average grade of 0.24% of U 3 O 8 from the levels zero-fourty of the El Nopal uraniferous deposit, located in the Sierra of Pena Blanca, State of Chihuahua (Mexico). The process which is proposed consist of 4 consecutive stages: a) The prehumectation with a fertile solution of a 0.0034 g U 3 O 8 /1 and 3 g H 2 SO 4 /l concentration, b) The counter current acid attack, c) The maturity or hardening, d) The washing with current water. The relaton liquid-solid in the stages of prehumectation, acid attack, as well as washing stage was of 0.3 m 3 /t. The average efficiency was of 77% of recovered *uranium. (author)

Acid-Gangue Interactions in Heap Leach Operations: A Review of the Role of Mineralogy for Predicting Ore Behaviour

Directory of Open Access Journals (Sweden)

Deshenthree Chetty

2018-01-01

Full Text Available Heap leaching accounts for a fifth of global copper production, sourced primarily from porphyry ores, yet metal recoveries are often not optimal. Gangue, and its interaction with acid, plays an important role in such processes. Thus, a proper understanding of gangue minerals present in the ore, their textural relationships relative to particle size distribution, reactivity with acid under different conditions, and relationship to lithotypes and geological alteration in the orebody, is necessary to predict ore behaviour in the comminution, agglomeration, curing and heap leach unit operations. Mineralogical tools available for characterisation are routine X-ray diffraction, optical microscopy, automated scanning electron microscopy, and electron probe microanalysis, accompanied by more recent advancements in hyperspectral infrared imaging and X-ray computed tomography. Integrated use of these techniques allows mineral abundance, textural relationships and mineral chemistry to be addressed over the range of particle and agglomerate sizes. Additionally, diagnostic leach results can be better interpreted when calibrated against robust mineralogical data. The linkage of ore attributes, metallurgical behaviour and their distribution in the orebody forms an integral part of a geometallurgical approach to predicting, and addressing, changes during the heap leaching process. Further investigation should address the fundamentals of gangue reaction with strong acid, and concomitant structural breakdown during curing and agglomeration processes, and how this differs from gangue-acid reactivity under weaker acid conditions, combined with temperature and fluid flow effects of heap leaching. Pre-and post- characterisation is necessary to understand and quantify the effects of variables for gangue-acid reactivity in these various operations. The characterisation outcomes should lead to a refinement of the hierarchy of gangue mineral reactivity under different

Application of Reactive Transport Modeling to Heap Bioleaching of Copper

Science.gov (United States)

Liu, W.

2017-12-01

Copper heap bioleaching is a complex industrial process that utilizes oxidative chemical leaching and microbial activities to extract copper from packed ore beds. Mathematical modelling is an effective tool for identifying key factors that determine the leaching performance. HeapSim is a modelling tool that incorporates all fundamental processes that occur in a heap under leach, such as the movement of leaching solution, chemical reaction kinetics, heat transfer, and microbial activities, to predict the leaching behavior of a heap. In this study, the HeapSim model was applied to simulate chalcocite heap bioleaching at Quebrada Blanca mine located in the Northern Chile. The main findings were that the model could be satisfactorily calibrated and validated to simulate chalcocite leaching. Heap temperature was sensitive to the changes in the raffinate temperature, raffinate flow rate, and the extent of pyrite oxidation. At high flow rates, heap temperature was controlled by the raffinate temperature. In contrast, heat removal by the raffinate solution flow was insignificant at low flow rates, leading to the accumulation of heat generated by pyrite reaction and therefore an increase in heap temperature.

Site selection and general layout of heap leaching uranium mill

International Nuclear Information System (INIS)

Zhang Chunmao; Rongfeng

2011-01-01

The site selection and general layout of uranium mill is an important work in the design and consultation stage of uranium mining and metallurgy's engineering construction. Based on the design practices, the principles and methods for the site selection and general layout of heap leaching uranium mill are analyzed and studied. Some problems which should be paid much attention to in the design are discussed in hopes of providing a useful reference for the design and consultation of similar projects. (authors)

Biomembrane oxidizing tank used in the process of bacterial heap leaching of uranium ore

International Nuclear Information System (INIS)

Meng Yunsheng; Fan Baotuan; Liu Jian; Zheng Ying; Liu Chao

2004-01-01

The construction characteristic of biomembrane oxidizing tank and specialty of packing material used in the process of bacterial heap leaching of uranium ore are introduced in this paper. Method for designing biomembrane oxidizing tank, layout principle of aeration system and measurements on running management are summarized

Studies on feasibility of recovering uranium from Dongkeng second class submarginal ore by heap leaching

International Nuclear Information System (INIS)

Yang Qingyi

1994-01-01

It was proved that it is feasible in economy and in technology to recover uranium from Dongkeng second class submarginal ore by heap leaching, on the basis of analysing the conditions of Mine No. 743 and the tests conducted. Moreover, the social and environmental effects are good. Two valuable suggestions are presented

Critical parameters in the dump and heap leaching of gold, silver, copper and uranium: permeability, solution delivery and solution recovery

Energy Technology Data Exchange (ETDEWEB)

Lastra, M.K.; Chase, C.K.

1984-02-01

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationals for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Critical parameters in the dump and heap leaching of gold, silver, copper and uranium: permeability, solution delivery and solution recovery

International Nuclear Information System (INIS)

Lastra, M.K.; Chase, C.K.

1984-01-01

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationals for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall

Volume reducing and modifying of neutralized sludge from acid waste water treatment of uranium ore heap leaching

International Nuclear Information System (INIS)

Zhong Pingru; Ding Tongsen; Gu Jianghan

1997-01-01

A process is worked out on the basis of traditional lime neutralization, viz. acid waste water from uranium ore heap leaching is treated by limestone and lime double neutralizing-sludge recycling. First, the waste water is reacted with cheaper limestone to precipitate some metal ions, such as Fe and Al, which form hydroxides at lower pH, and neutralize strong acid, then neutralized with lime to required pH value. The formed precipitate as sludge is steadily recycled in the process. The principal advantage of the process over lime neutralization process is that reagent cost saved by 1/3 and formed sludge volume decreased by 2/3. Besides, the performances of sludge filtrating and settling are improved. The mechanism of sludge volume reducing and modification is also investigated

Microbial communities from different subsystems in biological heap leaching system play different roles in iron and sulfur metabolisms.

Science.gov (United States)

Xiao, Yunhua; Liu, Xueduan; Ma, Liyuan; Liang, Yili; Niu, Jiaojiao; Gu, Yabing; Zhang, Xian; Hao, Xiaodong; Dong, Weiling; She, Siyuan; Yin, Huaqun

2016-08-01

The microbial communities are important for minerals decomposition in biological heap leaching system. However, the differentiation and relationship of composition and function of microbial communities between leaching heap (LH) and leaching solution (LS) are still unclear. In this study, 16S rRNA gene sequencing was used to assess the microbial communities from the two subsystems in ZiJinShan copper mine (Fujian province, China). Results of PCoA and dissimilarity test showed that microbial communities in LH samples were significantly different from those in LS samples. The dominant genera of LH was Acidithiobacillus (57.2 ∼ 87.9 %), while Leptospirillum (48.6 ∼ 73.7 %) was predominant in LS. Environmental parameters (especially pH) were the major factors to influence the composition and structure of microbial community by analysis of Mantel tests. Results of functional test showed that microbial communities in LH utilized sodium thiosulfate more quickly and utilized ferrous sulfate more slowly than those in LS, which further indicated that the most sulfur-oxidizing processes of bioleaching took place in LH and the most iron-oxidizing processes were in LS. Further study found that microbial communities in LH had stronger pyrite leaching ability, and iron extraction efficiency was significantly positively correlated with Acidithiobacillus (dominated in LH), which suggested that higher abundance ratio of sulfur-oxidizing microbes might in favor of minerals decomposition. Finally, a conceptual model was designed through the above results to better exhibit the sulfur and iron metabolism in bioleaching systems.

Mathematical simulation of a waste rock heap

International Nuclear Information System (INIS)

Scharer, J.M.; Pettit, C.M.; Chambers, D.B.; Kwong, E.C.

1994-01-01

A computer model has been developed to simulate the generation of acidic drainage in waste rock piles. The model considers the kinetic rates of biological and chemical oxidation of sulfide minerals (pyrite, pyrrhotite) present as fines and rock particles, as well as chemical processes such as dissolution (kinetic or equilibrium controlled), complexation (from equilibrium and stoichiometry of several complexes), and precipitation (formation of complexes and secondary minerals). Through mass balance equations and solubility constraints (e.g., pH, phase equilibria) the model keeps track of the movement of chemical species through the waste pile and provides estimates of the quality of seepage (pH, sulfate, iron, acidity, etc.) leaving the heap. The model has been expanded to include the dissolution (thermodynamic and sorption equilibrium), adsorption and coprecipitation of uranium and radium. The model was applied to simulate waste rock heaps in British Columbia, Canada and in Thueringia, Germany. To improve the accuracy and confidence of long-term predictions of seepage quality, the entire history of the heaps was simulated. Cumulative acidity loads and water treatment considerations were used as a basis for evaluation of various decommissioning alternatives. Simulation of the technical leaching history of a heap in Germany showed it will generate contaminated leachate requiring treatment for acidity and radioactivity for several hundred years; cover installation was shown to provide a significant reduction of potential burdens, although chemical treatment would still be required beyond 100 years

Uranium mining and heap leaching in India and related safety measures - A case study of Jajawal mines

International Nuclear Information System (INIS)

Saxena, V.P.; Verma, S.C.

2001-01-01

Exploration and exploitation of uranium involves drilling, mining, milling and extraction processes including heap leaching in some cases. At the exploration stage, the country's laws related to statutory environmental clearance covering forest and sanctuaries or Coastal Regulatory Zones (CRZ) are equally applicable for atomic minerals. At the developmental mining or commercial exploitation stage in addition to the environmental impact assessment, the provisions of Atomic Energy (working of Mines, Minerals and handling of Prescribed Substances) Rules 1984 are also to be followed which covers radiation monitoring, pollution control and other safety measures which are enforced by licensing authorities and the Atomic Energy Regulatory Board (AERB) of India. In India, Jaduguda, Bhatin, Narwapahar in Singhbhum Thrust Belt (STB), Asthota and Khiya in Siwaliks, Domiasiat in Cretaceous sandstones, Bodal and Jajawal in Precambrian crystallines, are some of the centres where mining has been carried out up to various underground levels. Substantial amount of dust and radon gas are generated during mining and milling operations. Though uranium mining is considered as hazardous for contamination by radionuclides, it is observed that many non-uranium mines have registered up to 100 mWL radon concentration, e.g. copper mines in STB area show up to 900 mewl in a few cases. Compared to this the Uranium mines in India have not shown any increase over the limits prescribed by AERB. Specific problems associated with mining include release of radon and other radioactive pollutants like Th-230, Ra-226, Pb-210 and Po-210, substantial dust generation, ground water contamination, proximity of population to working mines and environmental surveillance. These problems are adequately handled by periodical monitoring of various radiological parameters such as radon daughter working level, long lived alpha activity and concentration of radionuclides in gaseous, liquid and solid medium. Pre

Modelling water and contaminant transport in the Rum Jungle Mine overburden heaps

International Nuclear Information System (INIS)

Pantelis, G.

1987-04-01

An outline is given of a computer model for water and contaminant transport in and around overburden heaps, with those at the Rum Jungle mine site as a specific example. The model assumes the heaps to lie on a sloping shallow aquifer with identical hydraulic properties. The simulation is carried out for a 40 year period. After the first 20 years a cover which is effectively impermeable to infiltrating rainwater and air is introduced on the heap. The restriction of oxygen supply to the heap terminates contaminant production which results from oxidation of pyrite. Leaching of contaminants from the heap in the following 20-year period is examined

The Effect of Initial Irrigation Conditions on Heap Leaching Efficiency

Science.gov (United States)

Briseño Arellano, A. D.; Milczarek, M.; Yao, M.; Brusseau, M. L. L.

2017-12-01

Heap leaching is an unsaturated flow metal recovery process, in which mined ore is irrigated with a lixiviant to dissolve metal contained in the ore. The metal is then extracted from solution. Large scale operations involve stacking ore to depths of 6 to 18 meters on pads that may be hundreds of hectares in area. Heterogeneities within the stacked ore can lead to uneven wetting and the formation of preferential flow pathways, which reduces solution contact and lowers metal recovery. Furthermore, mineral dissolution can cause alteration of the porous media structure and loss of ore permeability. Many mine operators believe that slow initial irrigation rates help minimize permeability loss and increase metal recovery rates. However, this phenomenon has not been studied in detail. Experiments were conducted to investigate the effect of varying initial irrigation rates on leach ore stability. These were conducted with large columns (1.5 m high, 0.5 m in diameter) packed with crushed ore samples that are known to have permeability constraints. The columns were highly instrumented to assess potential changes in material properties both spatially and temporally. Water content was measured with three different methods: capacitance soil moisture sensors placed at 20-cm intervals; a neutron probe to periodically log every 30 cm from four different directions; and electrical resistivity sensors to create a 2-dimensional tomography profile of water content over time. Tensiometers were paired with the soil moisture sensors to measure matric suction and characterize moisture retention characteristics. A non-reactive tracer was used to characterize advective-dispersive transport under unsaturated conditions. A dye solution was introduced at the end of each experiment to map preferential pathways. Continuous monitoring of settling at the surface assisted in measuring consolidation and loss in permeability.

Bacteria heap leaching test of a uranium ore

International Nuclear Information System (INIS)

Liu Hui; Liu Jinhui; Wu Weirong; Han Wei

2008-01-01

Column bioleaching test of a uranium ore was carried out. The optimum acidity, spraying intensity, spray-pause time ratio were determined. The potential, Fe and U concentrations in the leaching process were investigated. The effect of bacteria column leaching was compared with that of acid column leaching. The results show that bacteria column leaching can shorten leaching cycle, and the leaching rate of uranium increases by 9.7%. (authors)

Leaching process

International Nuclear Information System (INIS)

Heinen, H.J.; McClelland, G.E.; Lindstrom, R.E.

1982-01-01

A gold and uranium ore is heap leached in accordance with the process comprising initial agglomeration of fines in the feed by means of a binding agent and cyanide solution. The lixiviant comprises a compatible mixture of sodium cyanide and sodium bicarbonate

Leaching process

Energy Technology Data Exchange (ETDEWEB)

Heinen, H J; McClelland, G E; Lindstrom, R E

1982-10-18

A gold and uranium ore is heap leached in accordance with the process comprising initial agglomeration of fines in the feed by means of a binding agent and cyanide solution. The lixiviant comprises a compatible mixture of sodium cyanide and sodium bicarbonate.

Biodesulphurisation of high sulphur coal by heap leaching

Energy Technology Data Exchange (ETDEWEB)

J. Cara; M.T. Carballo; A. Moran; D. Bonilla; O. Escolano; F.J. Garcia Frutos [Universidad de Leon, Leon (Spain). Departamento de Ingenieria Quimica

2005-10-01

The biodesulphurisation of coal carried out in pile could be an interesting option to clean coal. In view of the good results obtained in biodesulphurisation test column at lab scale on a sample of semianthracite coal that proceed of an industrial plant with a high sulphur content, mainly pyritic sulphur, the feasibility of the process at pilot plant scale was studied. The pile was formed with 6 ton of gravity middlings coal sample with a grain size -12+0.5 mm from S.A. Hullera Vasco-Leonesa industrial plant. The coal has a total sulphur content of 3.78% and a pyritic sulphur content of 2.88%, the rest of sulphur is organic sulphur. The biodesulphurisation process in pilot plant follows three stages: stabilization of the pile, biodesulphurisation and washing. Heap was sampled twice during stabilisation stage, at the end of desulphurisation process and finally once washed. A pyritic sulphur removal of 39% and total sulphur removal of 23% was obtained. To complete the bioleaching process, the treatment of purge of leachate was carried out with the objective to recycling to head of process. The best treatment was a pre-treatment of the leachate until pH 4, and further treatment by reverse osmosis of the clarified water. Comparing this process with conventional precipitation to reach disposal limits, the reagents consumption and sludges were reduced considerably and due to the high quality of permeate it permits to recycle it to head of process. 18 refs., 6 figs., 6 tabs.

Application of percolation leaching in Fuzhou uranium mine

International Nuclear Information System (INIS)

Jiang Lang; Wang Haita; He Jiangming

2006-01-01

In order to solve these problems such as high cost by conventional agitation leaching, low permeability and low leaching rate by heap leach, a percolation leaching method was developed. Two-year's production results show that leaching rate of uranium is up to 90% by this method. Compared with conventional agitation leaching, the power, sulfuric acid and lime consumption by the percolation leaching decreased by 60%, 27% and 77% respectively. (authors)

Bicarbonate leaching of uranium

International Nuclear Information System (INIS)

Mason, C.

1998-01-01

The alkaline leach process for extracting uranium from uranium ores is reviewed. This process is dependent on the chemistry of uranium and so is independent on the type of mining system (conventional, heap or in-situ) used. Particular reference is made to the geochemical conditions at Crownpoint. Some supporting data from studies using alkaline leach for remediation of uranium-contaminated sites is presented

Bicarbonate leaching of uranium

Energy Technology Data Exchange (ETDEWEB)

Mason, C.

1998-12-31

The alkaline leach process for extracting uranium from uranium ores is reviewed. This process is dependent on the chemistry of uranium and so is independent on the type of mining system (conventional, heap or in-situ) used. Particular reference is made to the geochemical conditions at Crownpoint. Some supporting data from studies using alkaline leach for remediation of uranium-contaminated sites is presented.

Crud treatment with 3 phase centrifuge in heap leach uranium process

International Nuclear Information System (INIS)

Hartmann, T.

2010-01-01

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal Uranium industry. The crud forms in the settlers of SX extraction. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. Spreading of this intermediate phase is determined by the following influencing factors. Wind blows dust into the open settlers, some suspended solids coming with the pregnant leach solution (PLS) and wrong design of the mixers cause stable emulsions. Metallic solid residue is likewise responsible for the growth rate of the crud at the above-mentioned phase boundary. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowinning (EW) cell can cause 'cathode burn'. The entrainment of electrolyte into the extraction stage can result in loss of pH control in the extraction circuit which will cause a drop in extraction efficiency. On the other hand, entrainment of the organic in the raffinate will result in organic losses to the leach circuit. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. The main benefit for the customer is that process fluctuations in the extraction process will no longer occur. The 3-phase separating solid bowl centrifuge consists of an axial solid-wall bowl. The solid-wall bowl has a cylindrical section for simultaneous separation and clarification of the aqueous and organic liquid phase and a conical section for efficient solids dewatering. The 3-phase feed suspension is fed into the solid bowl

Disposal of leached residual in heap leaching by neutralization

International Nuclear Information System (INIS)

Wang Jingmin

1993-01-01

The disposal results of leached residual with lime are described. Using the ratio of residual to lime being 100 : 1 the ideal disposal results were obtained with the effluent of the neutralized residual close to neutral

Heap leach studies on the removal of uranium from soil. Report of laboratory-scale test results

Energy Technology Data Exchange (ETDEWEB)

Turney, W.R.J.R.; York, D.A.; Mason, C.F.V.; Chisholm-Brause, C.J.; Dander, D.C.; Longmire, P.A.; Morris, D.E.; Strait, R.K.; Brewer, J.S.

1994-05-01

This report details the initial results of laboratory-scale testing of heap leach that is being developed as a method for removing uranium from uranium-contaminated soil. The soil used was obtained from the site of the Feed Materials Production Center (FMPC) near the village of Fernald in Ohio. The testing is being conducted on a laboratory scale, but it is intended that this methodology will eventually be enlarged to field scale where, millions of cubic meters of uranium-contaminated soil can be remediated. The laboratory scale experiments show that, using carbonate/bicarbonate solutions, uranium can be effectively removed from the soil from initial values of around 600 ppM down to 100 ppM or less. The goal of this research is to selectively remove uranium from the contaminated soil, without causing serious changes in the characteristics of the soil. It is also hoped that the new technologies developed for soil remediation at FEMP will be transferred to other sites that also have uranium-contaminated soil.

Dynamic Characteristics and Model for Centralization Reaction of Acidic Tailings From Heap Leaching of Uranium Ore

International Nuclear Information System (INIS)

Ding Dexin; Liu Yulong; Li Guangyue; Wang Youtuan

2010-01-01

Centralization tests were carried out on acidic tailings from heap leaching of uranium ore by using CaO, NaOH and NH 4 OH. The variations of pH with time were measured for the three centralization systems and the dynamic models for the systems were set up by regressing the measured data. The centralization process consists of the fast reaction phase representing the reaction between the centralization agent and the acid on the surface of the tailing's particles and the slow diffusion-reaction phase representing the diffusion-reaction between the centralization agent and the acid within the tailing's particles. The non-linear coupling and feedback function model for the diffusion-reaction of the centralization agent can reflect the process and mode of the centralization reaction. There is a non-linear oscillation in the variation of pH within the centralization systems. The dynamic model for the tailing's centralization reaction can fit the pH variation within the centralization systems. (authors)

Heap bioleaching of uranium from low-grade granite-type ore by mixed acidophilic microbes

International Nuclear Information System (INIS)

Xuegang Wang; Zhongkui Zhou

2017-01-01

We evaluated uranium bioleaching from low-grade, granite-type uranium ore using mixed acidophilic microbes from uranium mine leachate. A 4854-ton plant-scale heap bioleaching process achieved sustained leaching with a uranium leaching efficiency of 88.3% using a pH of 1.0-2.0 and an Fe"3"+ dosage of 3.0-5.5 g/L. Acid consumption amounted to 25.8 g H_2SO_4 kg"-"1 ore. Uranium bioleaching follows a diffusion-controlled kinetic model with a correlation coefficient of 0.9136. Almost all uranium was dissolved in aqueous solution, except those encapsulated in quartz particles. Therefore, heap bioleaching by mixed acidophilic microbes enables efficient, economical, large-scale recovery of uranium from low-grade ores. (author)

Strict fibonacci heaps

DEFF Research Database (Denmark)

Brodal, Gerth Stølting; Lagogiannis, George; Tarjan, Robert E.

2012-01-01

We present the first pointer-based heap implementation with time bounds matching those of Fibonacci heaps in the worst case. We support make-heap, insert, find-min, meld and decrease-key in worst-case O(1) time, and delete and delete-min in worst-case O(lg n) time, where n is the size of the heap...... of the smaller heap when doing a meld. We use the pigeonhole principle in place of the redundant counter mechanism. We present the first pointer-based heap implementation with time bounds matching those of Fibonacci heaps in the worst case. We support make-heap, insert, find-min, meld and decrease-key in worst...

ad-heap: an Efficient Heap Data Structure for Asymmetric Multicore Processors

DEFF Research Database (Denmark)

Liu, Weifeng; Vinter, Brian

2014-01-01

and its child nodes must be executed sequentially, and (2) heaps, even d-heaps (d-ary heaps or d-way heaps), cannot supply enough wide data parallelism to these processors. Recent research proposed more versatile asymmetric multicore processors (AMPs) that consist of two types of cores (latency......-oriented cores with high single-thread performance and throughput-oriented cores with wide vector processing capability), unified memory address space and faster synchronization mechanism among cores with different ISAs. To leverage the AMPs for the heap data structure, in this paper we propose ad......-heap, an efficient heap data structure that introduces an implicit bridge structure and properly apportions workloads to the two types of cores. We implement a batch k-selection algorithm and conduct experiments on simulated AMP environments composed of real CPUs and GPUs. In our experiments on two representative...

Static leaching of uraniferous shales on open areas

International Nuclear Information System (INIS)

Hernandez Nieto, J.; Cordero, G.; Villarrubia, M.

1973-01-01

This report describes the tests on acid heap leaching with conventional (1.400 ppm U 3 O 8 ) crushed uranium ores. We use open circuits with low internal recycled. Using starving acidity in the leaching solutions we obtain a smooth solubilization of uranium and, at the same time, the pregnant liquors are good for the solvent extraction recovery. (Author)

Dynamic of active microorganisms inhabiting a bioleaching industrial heap of low‐grade copper sulfide ore monitored by real‐time PCR and oligonucleotide prokaryotic acidophile microarray

Science.gov (United States)

Remonsellez, Francisco; Galleguillos, Felipe; Moreno‐Paz, Mercedes; Parro, Víctor; Acosta, Mauricio; Demergasso, Cecilia

2009-01-01

Summary The bioleaching of metal sulfide has developed into a very important industrial process and understanding the microbial dynamic is key to advancing commercial bioleaching operations. Here we report the first quantitative description of the dynamic of active communities in an industrial bioleaching heap. Acidithiobacillus ferrooxidans was the most abundant during the first part of the leaching cycle, while the abundance of Leptospirillum ferriphilum and Ferroplasma acidiphilum increased with age of the heap. Acidithiobacillus thiooxidans kept constant throughout the leaching cycle, and Firmicutes group showed a low and a patchy distribution in the heap. The Acidiphilium‐like bacteria reached their highest abundance corresponding to the amount of autotrophs. The active microorganisms in the leaching system were determined using two RNA‐based sensitive techniques. In most cases, the 16S rRNA copy numbers of At. ferrooxidans, L. ferriphilum, At. thiooxidans and F. acidiphilum, was concomitant with the DNA copy numbers, whereas Acidiphilium‐like bacteria and some Firmicutes members did not show a clear correlation between 16S rRNA accumulation and DNA copy numbers. However, the prokaryotic acidophile microarray (PAM) analysis showed active members of Alphaproteobacteria in all samples and of Sulfobacillus genus in older ones. Also, new active groups such as Actinobacteria and Acidobacterium genus were detected by PAM. The results suggest that changes during the leaching cycle in chemical and physical conditions, such as pH and Fe3+/Fe2+ ion rate, are primary factors shaping the microbial dynamic in the heap. PMID:21255296

Bipartite binomial heaps

DEFF Research Database (Denmark)

Elmasry, Amr; Jensen, Claus; Katajainen, Jyrki

2017-01-01

the (total) number of elements stored in the data structure(s) prior to the operation. As the resulting data structure consists of two components that are different variants of binomial heaps, we call it a bipartite binomial heap. Compared to its counterpart, a multipartite binomial heap, the new structure...

Thin-layer heap bioleaching of copper flotation tailings containing high levels of fine grains and microbial community succession analysis

Science.gov (United States)

Hao, Xiao-dong; Liang, Yi-li; Yin, Hua-qun; Liu, Hong-wei; Zeng, Wei-min; Liu, Xue-duan

2017-04-01

Thin-layer heap bioleaching of copper flotation tailings containing high levels of fine grains was carried out by mixed cultures on a small scale over a period of 210 d. Lump ores as a framework were loaded at the bottom of the ore heap. The overall copper leaching rates of tailings and lump ores were 57.10wt% and 65.52wt%, respectively. The dynamic shifts of microbial community structures about attached microorganisms were determined using the Illumina MiSeq sequencing platform based on 16S rRNA amplification strategy. The results indicated that chemolithotrophic genera Acidithiobacillus and Leptospirillum were always detected and dominated the microbial community in the initial and middle stages of the heap bioleaching process; both genera might be responsible for improving the copper extraction. However, Thermogymnomonas and Ferroplasma increased gradually in the final stage. Moreover, the effects of various physicochemical parameters and microbial community shifts on the leaching efficiency were further investigated and these associations provided some important clues for facilitating the effective application of bioleaching.

A Coupled Model for Solution Flow and Bioleaching Reaction Based on the Evolution of Heap Pore Structure

Directory of Open Access Journals (Sweden)

Shenghua Yin

2014-01-01

Full Text Available Based on the basic seepage law, equations have been derived to descript the solution flow within the copper ore heap which is treated as anisotropy porous media. The relationship between heap permeability and pore ratio has been revealed. Given the consideration of cover pressure and particle dissolution, pore evolution model has been set up. The pore evolution mechanism, due to the process of dissolution, precipitation, blockage, collapse, and caking, has been investigated. The comprehensive model for pore evolution and solution flow under the effect of solute transport and leaching reaction has been established. A trapezoidal heap was calculated, and the estimated results show that permeability decreases with the decreasing of pore ratio. Therefore, the permeability of the heap with small particles is relatively low because of its low pore ratio. Furthermore, permeability and height are found to be the two main factors influencing the solution flow.

Heap leaching of clay ish uranium ores

International Nuclear Information System (INIS)

Gonzalez, E.; Sedano, A.

1973-01-01

This paper describes an experimental facility, built near El Lobo mine. In it we study the beneficiation of low-grade uranium ore. The mineral has a great amount of clay and fines. The flow-sheet used has four steps: head leaching, ph-ajustement, ion-exchange and participation. We show, also, the most interesting results. (Author)

Study of uranium leaching from industrial residues of Industrias Nucleares do Brazil S.A. (INB), Caetite, Bahia, Brazil

International Nuclear Information System (INIS)

Formiga, Thiago S.; Morais, Carlos A.; Gomiero, Luiz A.

2011-01-01

The uraniferous district of Lagoa Real, located in the south-central region of the state of Bahia, has reserves estimated at 100,000 tons of uranium, which is enough to supply Angra I, II and III for 100 more years. The process adopted for the beneficiation of the uranium ore from Lagoa Real is heap leaching, a static process in which the ore is crushed, disposed in heaps and irrigated with a sulfuric acid solution to remove the uranium. This technique has a relatively low cost of implementation, although the yield of uranium recovery is low, with an uranium content in the leached residue of 700 μg/g U 3 O 8 for ores with an initial content of 2,700 μg/g U 3 O 8 . With the deepening of the mine pit, an increase in the carbonate content in the ore was noted, which required a higher acid consumption in the leaching. In order to reduce the concentration of carbonates, a study of the ore concentration by flotation column was accomplished. The flotation reject had high carbonate content, with a uranium content of about 2,300 μg/g U 3 O 8 for flotation in one column and 1,100 μg/g U 3 O 8 for flotation in two columns. This paper presents the study of the leaching process for the recovery of the uranium present in the residue of the heap leaching and in the carbonated residue from the flotation of the anomaly 13 ore. The results indicate the feasibility of treating the waste of the heap leaching through dynamic leaching. The study of the uranium leaching from the flotation residue through acid leaching technique indicated a recovery of 96% of uranium, however with a high consumption of acid, around 450 kg/t, showing that for this case, the most suitable technique for the process is alkaline leaching. (author)

Study of uranium leaching from industrial residues of Industrias Nucleares do Brazil S.A. (INB), Caetite, Bahia, Brazil

Energy Technology Data Exchange (ETDEWEB)

Formiga, Thiago S.; Morais, Carlos A., E-mail: cmorais@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Gomiero, Luiz A., E-mail: gomiero@inb.gov.b [Industrias Nucleares do Brasil S/A (INB), Caetite, BA (Brazil)

2011-07-01

The uraniferous district of Lagoa Real, located in the south-central region of the state of Bahia, has reserves estimated at 100,000 tons of uranium, which is enough to supply Angra I, II and III for 100 more years. The process adopted for the beneficiation of the uranium ore from Lagoa Real is heap leaching, a static process in which the ore is crushed, disposed in heaps and irrigated with a sulfuric acid solution to remove the uranium. This technique has a relatively low cost of implementation, although the yield of uranium recovery is low, with an uranium content in the leached residue of 700 {mu}g/g U{sub 3}O{sub 8} for ores with an initial content of 2,700 {mu}g/g U{sub 3}O{sub 8}. With the deepening of the mine pit, an increase in the carbonate content in the ore was noted, which required a higher acid consumption in the leaching. In order to reduce the concentration of carbonates, a study of the ore concentration by flotation column was accomplished. The flotation reject had high carbonate content, with a uranium content of about 2,300 {mu}g/g U{sub 3}O{sub 8} for flotation in one column and 1,100 {mu}g/g U{sub 3}O{sub 8} for flotation in two columns. This paper presents the study of the leaching process for the recovery of the uranium present in the residue of the heap leaching and in the carbonated residue from the flotation of the anomaly 13 ore. The results indicate the feasibility of treating the waste of the heap leaching through dynamic leaching. The study of the uranium leaching from the flotation residue through acid leaching technique indicated a recovery of 96% of uranium, however with a high consumption of acid, around 450 kg/t, showing that for this case, the most suitable technique for the process is alkaline leaching. (author)

Analysis of factors affecting the effect of stope leaching

International Nuclear Information System (INIS)

Xie Wangnan; Dong Chunming

2014-01-01

The industrial test and industrial trial production of stope leaching were carried out at Taoshan orefield of Dabu deposit. The results of test and trial production showed obvious differences in leaching rate and leaching time. Compared with industrial trial production of stope leaching, the leaching rate of industrial test was higher, and leaching time was shorter. It was considered that the blasting method and liquid arrangement were the main factors affecting the leaching rate and leaching time according to analysis. So we put forward the following suggestions: the technique of deep hole slicing tight-face blasting was used to reduce the yield of lump ores, the effective liquid arrangement methods were adopted to make the lixiviant infiltrating throughout whole ore heap, and bacterial leaching was introduced. (authors)

Fat heaps

DEFF Research Database (Denmark)

Elmasry, Amr Ahmed Abd Elmoneim; Katajainen, Jyrki

This report is an electronic appendix to our paper \\Fat heaps without regular counters". In that paper we described a new variant of fat heaps that is conceptually simpler and easier to implement than the original version. We also compared the practical performance of this data structure...

Hydrodynamics and mass transfer in trickle leaching process

International Nuclear Information System (INIS)

Jin Suoqing; Xiang Qinfang; Guo Jianzheng

1995-01-01

The initial research results of the hydrodynamic behavior and mass transfer of the trickle leaching process are summarized. It was shown that the dropping mode, the height of uranium ore heap and the flow rate of the dropping fluid affect the mass transfer of the trickle leaching process. Based on the concept of the keeping form of liquid in ore particle bed and the diffusion in porous medium, a mass transfer pattern, i.e. 'double-membrane transfer process' controlled by porous diffusion, was presented and proved for trickle leaching process

Geological and technological evaluation of gold-bearing mineral material after photo-electrochemical activation leaching

Science.gov (United States)

Manzyrev, DV

2017-02-01

The paper reports the lab test results on simulation of heap leaching of unoxidized rebellious ore extracted from deep levels of Pogromnoe open pit mine, with different flowsheets and photo-electrochemically activated solutions. It has been found that pre-treatment of rebellious ore particles -10 mm in size by photo-electrochemically activated solutions at the stage preceding agglomeration with the use of rich cyanide solutions enhances gold recovery by 6%.

Study of a bacterial leaching program for uranium ores by Thiobacillus ferroxidans

International Nuclear Information System (INIS)

Garcia Junior, O.

1989-01-01

The development of a bacterial leaching program for uranium ores is studied. Three basic points are presented: isolation and purification of Thiobacillus ferroxidans, as well Thiobacillus thio oxidans; physiological studies of growth and respiratory metabolism of T. ferroxidans; uranium leaching from two types of ore by T. ferroxidans action, on laboratory, semi pilot and pilot scales. The bacterial leaching studies were carried out in shake flasks, percolation columns (laboratory and semi pilot) and in heap leaching (pilot). The potential of the ores studied in relation to bacterial action, was first showed in shake flask experiments. The production of H 2 S O 4 and Fe 3+ was a result of the bacterial activity on both ore samples containing pyrite (Fe S 2 ). These two bacterial products resulted in a high uranium and molybdenum extraction and a lower sulfuric acid consumption compared to the sterilized treatments. Similar results were obtained in percolation column at the same scale (lab). (author)

Utilization of low grade and waste uranium ores by means of biological processes. Part of a coordinated programme on bacterial leaching of uranium ores

International Nuclear Information System (INIS)

Czegledi, B.

1978-01-01

Investigation of the possible affect of bacteria in leaching uranium using alkaline carbonate medium has been investigated. Eleven strains of bacteria were isolated from the alkaline percolation solutions. Most belonged to the genus Thiobacillus. Each strain was characterized by growth under aerobic conditions in Levinthal - bouillon medium and under vaseline (semi-anaerobic in Hetehens medium. Growth of the bacteria was optimum at pH range 7 to 8 but a significant population was found to exist in alkaline leaching solutions of about pH 9 to 9.5 in heap leaching experiments. It was concluded that microbiological processes can play a role in alkaline heap leaching although the quantitative measure is yet uncertain

Influence of Sulfobacillus thermosulfidooxidans on Initial Attachment and Pyrite Leaching by Thermoacidophilic Archaeon Acidianus sp. DSM 29099

Directory of Open Access Journals (Sweden)

Jing Liu

2016-07-01

Full Text Available At the industrial scale, bioleaching of metal sulfides includes two main technologies, tank leaching and heap leaching. Fluctuations in temperature caused by the exothermic reactions in a heap have a pronounced effect on the growth of microbes and composition of mixed microbial populations. Currently, little is known on the influence of pre-colonized mesophiles or moderate thermophiles on the attachment and bioleaching efficiency by thermophiles. The objective of this study was to investigate the interspecies interactions of the moderate thermophile Sulfobacillus thermosulfidooxidans DSM 9293T and the thermophile Acidianus sp. DSM 29099 during initial attachment to and dissolution of pyrite. Our results showed that: (1 Acidianus sp. DSM 29099 interacted with S. thermosulfidooxidansT during initial attachment in mixed cultures. In particular, cell attachment was improved in mixed cultures compared to pure cultures alone; however, no improvement of pyrite leaching in mixed cultures compared with pure cultures was observed; (2 active or inactivated cells of S. thermosulfidooxidansT on pyrite inhibited or showed no influence on the initial attachment of Acidianus sp. DSM 29099, respectively, but both promoted its leaching efficiency; (3 S. thermosulfidooxidansT exudates did not enhance the initial attachment of Acidianus sp. DSM 29099 to pyrite, but greatly facilitated its pyrite dissolution efficiency. Our study provides insights into cell-cell interactions between moderate thermophiles and thermophiles and is helpful for understanding of the microbial interactions in a heap leaching environment.

Treatment of copper ores containing atacamite by the brisa process

International Nuclear Information System (INIS)

Carranza, F.; Mazuelos, A.; Romero, R.

2003-01-01

The current treatment of copper ores containing atacamite and secondary copper sulphides consists of heap leaching, by the TL process. copper recoveries by this treatment are very low (less than 50% for operating times higher than six months). In order to improve the copper extraction yields, several treatment options are presented in this work, wich consist on promoting the acid leaching of the atacamite and the indirect bio leaching (Brisk process) of the secondary copper sulphides. All the options lead to improved copper recoveries in comparison with the current treatment. An economic estimation of each option of treatment is included, with really attractive results. (Author) 13 refs

Two-tier relaxed heaps

DEFF Research Database (Denmark)

Elmasry, Amr; Jensen, Claus; Katajainen, Jyrki

2008-01-01

We introduce a data structure which provides efficient heap operations with respect to the number of element comparisons performed. Let n denote the size of the heap being manipulated. Our data structure guarantees the worst-case cost of O(1) for finding the minimum, inserting an element, extract...

Small-scale and large-scale testing of photo-electrochemically activated leaching technology in Aprelkovo and Delmachik Mines

Science.gov (United States)

Sekisov, AG; Lavrov, AYu; Rubtsov, YuI

2017-02-01

The paper gives a description of tests and trials of the technology of heap gold leaching from rebellious ore in Aprelkovo and Delmachik Mines. Efficiency of leaching flowsheets with the stage-wise use of activated solutions of different reagents, including active forms of oxygen, is evaluated. Carbonate-peroxide solutions are used at the first stage of leaching to oxidize sulfide and sulfide-arsenide ore minerals to recover iron and copper from them. The second stage leaching uses active cyanide solutions to leach encapsulated and disperse gold and silver.

Current scenario of chalcopyrite bioleaching: a review on the recent advances to its heap-leach technology.

Science.gov (United States)

Panda, Sandeep; Akcil, Ata; Pradhan, Nilotpala; Deveci, Haci

2015-11-01

Chalcopyrite is the primary copper mineral used for production of copper metal. Today, as a result of rapid industrialization, there has been enormous demand to profitably process the low grade chalcopyrite and "dirty" concentrates through bioleaching. In the current scenario, heap bioleaching is the most advanced and preferred eco-friendly technology for processing of low grade, uneconomic/difficult-to-enrich ores for copper extraction. This paper reviews the current status of chalcopyrite bioleaching. Advanced information with the attempts made for understanding the diversity of bioleaching microorganisms; role of OMICs based research for future applications to industrial sectors and chemical/microbial aspects of chalcopyrite bioleaching is discussed. Additionally, the current progress made to overcome the problems of passivation as seen in chalcopyrite bioleaching systems have been conversed. Furthermore, advances in the designing of heap bioleaching plant along with microbial and environmental factors of importance have been reviewed with conclusions into the future prospects of chalcopyrite bioleaching. Copyright © 2015 Elsevier Ltd. All rights reserved.

Imouraren - uranium leaching tests and specificities with analcites

International Nuclear Information System (INIS)

Wattinne-Morice, A.; Belieres, M.

2010-01-01

Imouraren is a sedimentary uranium deposit (total > 150 000 tU, average U ~ 0.08 %), located in Niger (~ 100 km from Agadez). Uranium mineralization is trapped in sandstones and is widely oxidized (uranotyle, metatuyamunite), but a part remains reduced (pitchblende, uraninite). The sandstones have a peculiar mineralogical assemblage (analcite partly chloritized) which can affect uranium recovery. Several acid heap leaching tests have been completed to determine the most suitable process parameters. Microscopic studies and XRD analysis performed on fresh ore and on leached residue highlight the complex behavior of uranium and the associated mineralogical families during the tests. (author)

Norman Stuart heaps 1928”1986

Science.gov (United States)

Cartwright, David E.

Dr. Norman Heaps died on June 26, 1986, in a hospital near his native town of Prescot, U.K., a suburb of Liverpool, after a long illness punctuated by bouts of painful medical treatment for lung cancer. He was the pioneer in Britain of the numerical modeling of tides and storm surges in shelf seas.He graduated at the University of Liverpool in 1949 with honors in mathematics with subsidiary physics and oceanography. Many years later the same university awarded him a doctorate on the basis of his published work. Norman's first 10 postgraduate years were spent as mathematician in the aircraft industry, but he never felt at home in the industrial world and sought a more academic career. While lecturing at the Royal College of Advanced Technology at Salford, Manchester (now the University of Salford), he struck a lasting friendship with Clifford Mortimer, FRS, then director of the Freshwater Biological Association laboratory at Lake Windermere, who first interested Heaps in the problem of computing the natural seiche oscillations of that lake. The use of electronic computers was still in its infancy, but Heaps saw that the equations of internal oscillations in such a lake could be solved numerically by methods that he had developed in the theory of wing structures. Heaps worked up a Master's thesis on this problem during his summer vacations, and he later worked with Mortimer at the University of Wisconsin on a more advanced scheme involving the coupled oscillations of Green Bay and Lake Michigan.

A case study of shrinkage-in place leaching of low grade uranium ore deposit

International Nuclear Information System (INIS)

Ding Dexin; Zhou Guohe

1998-09-01

A case study of shrinkage-in place leaching of low grade uranium ore deposit is dealt with. A test block was selected, and the shrinkage mining method was employed to construct the in place heap for leaching. Blast parameters and operations were carefully tried in order to make sure that the fragment size composition was adequate for leaching. A leaching system was planned and the corresponding leaching parameters were tried, too. The results show that the shrinkage method and the parameters for blasting and leaching are all adequate for the in-situ leaching of the blasted ore. This shrinkage-in place leaching system combines the mining and metallurgy processes into one and produces a lot of profits and could be applicable to many low grade uranium ore deposits which are so hard and compact that they have to be fragmented before being leached

Increasing flux rate to shorten leaching period and ramp-up production

Science.gov (United States)

Ngantung, Billy; Agustin, Riska; Ravi'i

2017-01-01

J Resources Bolaang Mongondow (JBRM) has operated a dynamic heap leach in its Bakan Gold Mine since late 2013. After successfully surpassing its name plate capacity of 2.6 MT/annum in 2014, the clayey and transition ore become the next operational challenge. The presence of transition and clayey ore requires longer leaching period, hence reducing the leach pad capacity which then caused reduced production. Maintaining or even increasing production with such longer leaching ore types can be done by expanding the leach pad area which means an additional capital investment, and/or shortening the leaching cycle which compromise a portion of gold extraction. JBRM has been successfully increasing the leach pad production from 2.6 MT/annum to 3.8 MT/annum, whilst improving the gold extraction from around 70% to around 80%. This was achieved by managing the operation of the leach pad which is shortening the leach cycle by identifying and combining the optimal flux rate application versus the tonne processed in each cell, at no capital investment for expanding the cell capacity.

Comparative study of ageing, heat treatment and accelerated carbonation for stabilization of municipal solid waste incineration bottom ash in view of reducing regulated heavy metal/metalloid leaching.

Science.gov (United States)

Santos, Rafael M; Mertens, Gilles; Salman, Muhammad; Cizer, Özlem; Van Gerven, Tom

2013-10-15

This study compared the performance of four different approaches for stabilization of regulated heavy metal and metalloid leaching from municipal solid waste incineration bottom ash (MSWI-BA): (i) short term (three months) heap ageing, (ii) heat treatment, (iii) accelerated moist carbonation, and (iv) accelerated pressurized slurry carbonation. Two distinct types of MSWI-BA were tested in this study: one originating from a moving-grate furnace incineration operation treating exclusively household refuse (sample B), and another originating from a fluid-bed furnace incineration operation that treats a mixture of household and light industrial wastes (sample F). The most abundant elements in the ashes were Si (20-27 wt.%) and Ca (16-19 wt.%), followed by significant quantities of Fe, Al, Na, S, K, Mg, Ti, and Cl. The main crystalline substances present in the fresh ashes were Quartz, Calcite, Apatite, Anhydrite and Gehlenite, while the amorphous fraction ranged from 56 to 73 wt.%. The leaching values of all samples were compared to the Flemish (NEN 7343) and the Walloon (DIN 38414) regulations from Belgium. Batch leaching of the fresh ashes at natural pH showed that seven elements exceeded at least one regulatory limit (Ba, Cr, Cu, Mo, Pb, Se and Zn), and that both ashes had excess basicity (pH > 12). Accelerated carbonation achieved significant reduction in ash basicity (9.3-9.9); lower than ageing (10.5-12.2) and heat treatment (11.1-12.1). For sample B, there was little distinction between the leaching results of ageing and accelerated carbonation with respect to regulatory limits; however carbonation achieved comparatively lower leaching levels. Heat treatment was especially detrimental to the leaching of Cr. For sample F, ageing was ineffective and heat treatment had marginally better results, while accelerated carbonation delivered the most effective performance, with slurry carbonation meeting all DIN limits. Slurry carbonation was deemed the most

Report on the progress of work in Portugal [Processing of Low-Grade Uranium Ores]; Rapport sur l'etat d'avancement des travaux au Portugal

Energy Technology Data Exchange (ETDEWEB)

Carreira Pich, H [Junta de Energia Nuclear, Laboratorio de Fisica e Engenharia Nucleares, Sacavem (Portugal)

1967-06-15

The purpose of the principal studies until now in Portugal were the development of two types of treatment of the uranium minerals: - Traditional leaching by agitation of the ore milled in a finely sulphuric acid solution; - Leaching of the type 'heap leaching' in which the ore is hard crushed, and then sprinkles is crammed with sulphuric acid solution. Leaching tests were performed traditionally with samples of available Portuguese minerals. In most cases, the dissolution of uranium is easy and low consumption of acid. Efforts were oriented in the direction of a leaching type 'heap leaching'.

Static leaching of uraniferous shales on open areas; Lixiviacion estatica de izarras uraniferas (tratamiento de mineral rico en era abierta)

Energy Technology Data Exchange (ETDEWEB)

Hernandez Nieto, J; Cordero, G; Villarrubia, M

1973-07-01

This report describes the tests on acid heap leaching with conventional (1.400 ppm U{sub 3}O{sub 8}) crushed uranium ores. We use open circuits with low internal recycled. Using starving acidity in the leaching solutions we obtain a smooth solubilization of uranium and, at the same time, the pregnant liquors are good for the solvent extraction recovery. (Author)

Wagner’s theory of generalised heaps

CERN Document Server

Hollings, Christopher D

2017-01-01

The theories of V. V. Wagner (1908-1981) on abstractions of systems of binary relations are presented here within their historical and mathematical contexts. This book contains the first translation from Russian into English of a selection of Wagner’s papers, the ideas of which are connected to present-day mathematical research. Along with a translation of Wagner’s main work in this area, his 1953 paper ‘Theory of generalised heaps and generalised groups,’ the book also includes translations of three short precursor articles that provide additional context for his major work. Researchers and students interested in both algebra (in particular, heaps, semiheaps, generalised heaps, semigroups, and groups) and differential geometry will benefit from the techniques offered by these translations, owing to the natural connections between generalised heaps and generalised groups, and the role played by these concepts in differential geometry. This book gives examples from present-day mathematics where ideas r...

Linking leach chemistry and microbiology of low-grade copper ore bioleaching at different temperatures

Science.gov (United States)

Jia, Yan; Sun, He-yun; Tan, Qiao-yi; Gao, Hong-shan; Feng, Xing-liang; Ruan, Ren-man

2018-03-01

The effects of temperature on chalcocite/pyrite oxidation and the microbial population in the bioleaching columns of a low-grade chalcocite ore were investigated in this study. Raffinate from the industrial bioleaching heap was used as an irrigation solution for columns operated at 20, 30, 45, and 60°C. The dissolution of copper and iron were investigated during the bioleaching processes, and the microbial community was revealed by using a high-throughput sequencing method. The genera of Ferroplasma, Acidithiobacillus, Leptospirillum, Acidiplasma, and Sulfobacillus dominated the microbial community, and the column at a higher temperature favored the growth of moderate thermophiles. Even though microbial abundance and activity were highest at 30°C, the column at a higher temperature achieved a much higher Cu leaching efficiency and recovery, which suggested that the promotion of chemical oxidation by elevated temperature dominated the dissolution of Cu. The highest pyrite oxidation percentage was detected at 45°C. Higher temperature resulted in precipitation of jarosite in columns, especially at 60°C. The results gave implications to the optimization of heap bioleaching of secondary copper sulfide in both enhanced chalcocite leaching and acid/iron balance, from the perspective of leaching temperature and affected microbial community and activity.

Interacting via the Heap in the Presence of Recursion

Directory of Open Access Journals (Sweden)

Jurriaan Rot

2012-12-01

Full Text Available Almost all modern imperative programming languages include operations for dynamically manipulating the heap, for example by allocating and deallocating objects, and by updating reference fields. In the presence of recursive procedures and local variables the interactions of a program with the heap can become rather complex, as an unbounded number of objects can be allocated either on the call stack using local variables, or, anonymously, on the heap using reference fields. As such a static analysis is, in general, undecidable. In this paper we study the verification of recursive programs with unbounded allocation of objects, in a simple imperative language for heap manipulation. We present an improved semantics for this language, using an abstraction that is precise. For any program with a bounded visible heap, meaning that the number of objects reachable from variables at any point of execution is bounded, this abstraction is a finitary representation of its behaviour, even though an unbounded number of objects can appear in the state. As a consequence, for such programs model checking is decidable. Finally we introduce a specification language for temporal properties of the heap, and discuss model checking these properties against heap-manipulating programs.

Model of heap formation in vibrated gravitational suspensions.

Science.gov (United States)

Ebata, Hiroyuki; Sano, Masaki

2015-11-01

In vertically vibrated dense suspensions, several localized structures have been discovered, such as heaps, stable holes, expanding holes, and replicating holes. Because an inclined free fluid surface is difficult to maintain because of gravitational pressure, the mechanism of those structures is not understood intuitively. In this paper, as a candidate for the driving mechanism, we focus on the boundary condition on a solid wall: the slip-nonslip switching boundary condition in synchronization with vertical vibration. By applying the lubrication approximation, we derived the time evolution equation of the fluid thickness from the Oldroyd-B fluid model. In our model we show that the initially flat fluid layer becomes unstable in a subcritical manner, and heaps and convectional flow appear. The obtained results are consistent with those observed experimentally. We also find that heaps climb a slope when the bottom is slightly inclined. We show that viscoelasticity enhances heap formation and climbing of a heap on the slope.

Policy-based benchmarking of weak heaps and their relatives

DEFF Research Database (Denmark)

Bruun, Asger; Edelkamp, Stefan; Katajainen, Jyrki

2010-01-01

In this paper we describe an experimental study where we evaluated the practical efficiency of three worst-case efficient priority queues: 1) a weak heap that is a binary tree fulfilling half-heap ordering, 2) a weak queue that is a forest of perfect weak heaps, and 3) a runrelaxed weak queue tha...

Treatment of an isolated high-grade, low-tonnage uranium orebody

International Nuclear Information System (INIS)

Ajuria-Garza, S.

1976-01-01

A completely integrated process leading to a commercial-grade uranium concentrate has been developed for the El Nopal orebody which contains 115000t of ore with an average grade of 0.283%, equivalent to 325t of U 3 O 8 . The process consists of crushing (from -12 in to -1.5in), heap leaching with recirculation, a special type of countercurrent washing (also in the heap), solvent extraction to give an exceptionally high uranium concentration, re-extraction, precipitation with ammonium hydroxide, filtration and calcining. The main factors that influence heap leaching are analysed in detail: heap geometry, crushed ore size distribution, base design and construction, method of heaping, acid feeding method, flow of liquors through the heap and washing procedures. Leaching efficiencies range from 80 to 85% and washing efficiencies from 96 to almost 100% with an overall extraction efficiency of 77 to 85%. Acid consumption is usually less than 25kg/t of ore. The leaching and washing processes described are designed to use an overall solid-to-liquid ratio of about 3:1 thus producing very concentrated liquors with a U 3 O 8 content of about 7g/l. These liquors are filtered and fed directly to a solvent extraction system using Alamine 336 (tri-capryl amine) and isodecanol in kerosene. The high feed concentration makes it possible to use a high concentration of amine. The organic solvent contains 120g/l of Alamine and 98g/l of isodecanol. Re-extraction can be with a saline solution containing 100g/lNH 4 Cl and 250g/l(NH 4 )SO 4 . The strong liquor obtained from re-extraction contains 70-75g/lU 3 O 8 . The remaining steps of precipitation, filtration and calcining can then follow general practice and lead to a product which meets currently accepted commercial specifications. As an alternative, nitrate re-extraction has been shown to produce a solution of about 70g/l which will feed directly to tributyl phosphate (TBP) refining without the necessity of ever producing a

Improvement for waste water treatment process of a uranium deposite and its effect

International Nuclear Information System (INIS)

Huang Jimao

2013-01-01

Uranium was recovered from alkaline uranium ores by heap leaching and traditional agitation leaching methods at a uranium mine, and the waste water (including waste water produced in hydrometallurgy process and mine drainage) was treated by using chemical precipitation method and chemical precipitation loading method. It was found that the removal rate of uranium by the waste water treatment process was not satisfactory after one year's run. So, the waste water treatment process was improved. After the improvement, removal rate of CO 3 2- ,HCO 3 - , U and Ra was enhanced and the treated waste water reached the standard of discharge. (author)

The rehabilitation of Whites overburden heap

International Nuclear Information System (INIS)

Allen, C.G.

1984-01-01

The Rum Jungle uranium mine was closed in 1971. Environmental studies have identified sources of heavy metal and acid pollution and a rehabilitation strategy for the mine site has been proposed. The objectives of the program are the significant reduction of heavy metal pollution being released by the various overburden heaps, open cuts and the tailings dam to the East Finniss River; the significant improvement of the aesthetic environment of the site; and the reduction in public health hazards at the mine. The rehabilitation strategy includes recontouring, covering, draining and revegetating the overburden heap

Guide lines for control and supervision of dump leaching. Application to the inframarginal uranium ore of the Cellier mine

International Nuclear Information System (INIS)

Pineau, J.L.; Yvon, J.; Blazy, P.

1984-01-01

The Cellier mine processes inframarginal uranium ores by a slow dump leaching. Fragmentary information concerning the evolution of the chemical properties of the solutions (inflow-outflow) as a function of the time has been the object of an analysis of data. The latter, which was both descriptive and predictive, made it possible on the one hand to identify facts which have intervened at the time of leaching and on the other hand to pinpoint the influence of the time factor and of the associations of chemical elements (aluminium, phosphorus, etc.) on the passing into solution of the uranium. As this treatment gives only a global view of the problem, it was completed by a mineralogical analysis. The fine mineralogical analysis of the fractions, made soluble by sulphuric attack in a heap, shows that sulphated concretions isolate the uranium from the leaching liquor. A screen of sulphate is composed of a macroscopic web of gypsum (calcium sulphate) in which a microscopic web of hydrated magnesium sulphate is inserted. In the gypsum web are trapped phosphorus minerals and in the magnesium sulphate web manganese and aluminium minerals. As regards the uranium, it is either distributed in the form of fine inclusions of uranyl hydroxide, or associated to chlorinated forms, derived from the treatment aids [fr

Leaching of RA-226 contaminated gravel using different aqueous treatments

Energy Technology Data Exchange (ETDEWEB)

Mamoon, A; Abulfaraj, W H; Sohsah, M A [King Abdulaziz University, Jeddah, Saudi Arbabia (Saudi Arabia)

1997-12-31

Investigation of the efficiencies of different aqueous leaching treatments was carried out on gravel artificially contaminated with Ra-226. The extent of leaching efficiency was determined in terms of Ra-226 and its daughter Rn-222. Liquid scintillation counting using high efficiency mineral oil based liquid scintillator was the technique adopted for measuring Ra-226 and Rn-222 leached off the contaminated gravel. Water, dilute solutions of barium chloride and HCl were used as leachants. Different masses of gravel were leached with 200 mL of leachant for various contact time periods. The leached Rn-222 activity measured was plotted vs the decay factor e; from which Rn-222 and Ra-226 originally present in the sample were determined. Several leaching parameters were tested; namely type of leachant, leachant volume/gravel mass ratio, leachant contact time, effect of varying Ba Cl{sub 2} concentration, and successive leaching. Optimization of the leaching parameters for desorption of Ra-226 off the contaminated gravel under laboratory conditions may help determine the ideal conditions for remediating soil contaminated with radium or chemically similar radionuclides. 7 figs.

Worst-case analysis of heap allocations

DEFF Research Database (Denmark)

Puffitsch, Wolfgang; Huber, Benedikt; Schoeberl, Martin

2010-01-01

the worst-case heap allocations of tasks. The analysis builds upon techniques that are well established for worst-case execution time analysis. The difference is that the cost function is not the execution time of instructions in clock cycles, but the allocation in bytes. In contrast to worst-case execution...... time analysis, worst-case heap allocation analysis is not processor dependent. However, the cost function depends on the object layout of the runtime system. The analysis is evaluated with several real-time benchmarks to establish the usefulness of the analysis, and to compare the memory consumption...

The treatments of soil Rirang by floatation and Acid leaching

International Nuclear Information System (INIS)

Kosim-Affandi; Umar-Sarip; Alwi, Guswita; Sri-Sudaryanto

2000-01-01

The treatments of soil Rirang by floatation and acid leaching has been carried out to increase high uranium concentrates of materials, separating associated economical minerals and to reduce the gangue minerals which bothering at chemical processing. The physical treatment has been done by ore preparation and floatation using oleic acid and p ine oil , 20 % of pulp at pH 9, condition time at 5 minutes and collections of float fraction was 10 minutes. The chemical processing has been done by dynamic leaching using H 2 SO 4 100 kg/ton, MnO 2 20 kg/ton, 50 % of solid with ore size - 65 mesh, temperature at 80 o C and time of leaching was 8 hours. The result of experiments is as follows : Physical treatment by floatation shown that the concentrates of U increased at sink fraction by (1.5 - 2) times against feed sample for all the samples, and in the float fraction the recovery of molybdenite separation is 58 - 81 % and rare earths is 57 - 80 %. The result of dynamic leaching is 76 - 91 %, and recovery uranium increasing from 81.02 % (mixture samples soil before floatation) to 91.16 % ( mixture samples of float fraction)

Novel Binders and Methods for Agglomeration of Ore

Energy Technology Data Exchange (ETDEWEB)

S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

2006-09-30

Heap leaching is one of the methods being used to recover metal from low grade ore deposits. The main problem faced during heap leaching is the migration of fine grained particles through the heap, forming impermeable beds which result in poor solution flow. The poor solution flow leads to less contact between the leach solution and the ore, resulting in low recovery rates. Agglomeration of ore into coarse, porous masses prevents fine particles from migrating and clogging the spaces and channels between the larger ore particles. Currently, there is one facility in the United States which uses agglomeration. This operation agglomerates their ore using leach solution (raffinate), but is still experiencing undesirable metal recovery from the heaps due to agglomerate breakdown. The use of a binder, in addition to the leach solution, during agglomeration would help to produce stronger agglomerates that did not break down during processing. However, there are no known binders that will work satisfactorily in the acidic environment of a heap, at a reasonable cost. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. Increasing copper recovery in heap leaching by the use of binders and agglomeration would result in a significant decrease in the amount of energy consumed. Assuming that 70% of all the leaching heaps would convert to using agglomeration technology, as much as 1.64*10{sup 12} BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, which is equivalent to saving approximately 18% of the energy currently being used in leaching heaps. For every week a leach cycle was decreased, a savings of as much as 1.23*10{sup 11} BTU per week would result. This project has identified several acid-resistant binders and agglomeration procedures. These binders and experimental procedures will be able to be used for use in improving the energy efficiency of

Mineral-leaching chemical transport with runoff and sediment from severely eroded rare-earth tailings in southern China

Science.gov (United States)

Lu, Huizhong; Cao, Longxi; Liang, Yin; Yuan, Jiuqin; Zhu, Yayun; Wang, Yi; Gu, Yalan; Zhao, Qiguo

2017-08-01

Rare-earth mining has led to severe soil erosion in southern China. Furthermore, the presence of the mineral-leaching chemical ammonium sulfate in runoff and sediment poses a serious environmental threat to downstream water bodies. In this paper, the characteristics of mineral-leaching chemicals in surface soil samples collected in the field were studied. In addition, NH4+ and SO42- transport via soil erosion was monitored using runoff and sediment samples collected during natural rainfall processes. The results demonstrated that the NH4+ contents in the surface sediment deposits increased from the top of the heap (6.56 mg kg-1) to the gully (8.23 mg kg-1) and outside the tailing heap (13.03 mg kg-1). The contents of SO42- in the different locations of the tailing heaps ranged from 27.71 to 40.33 mg kg-1. During typical rainfall events, the absorbed NH4+ concentrations (2.05, 1.26 mg L-1) in runoff were significantly higher than the dissolved concentrations (0.93, 1.04 mg L-1), while the absorbed SO42- concentrations (2.87, 1.92 mg L-1) were significantly lower than the dissolved concentrations (6.55, 7.51 mg L-1). The dissolved NH4+ and SO42- concentrations in runoff displayed an exponentially decreasing tendency with increasing transport distance (Y = 1. 02 ṡ exp( - 0. 00312X); Y = 3. 34 ṡ exp( - 0. 0185X)). No clear trend with increasing distance was observed for the absorbed NH4+ and SO42- contents in transported sediment. The NH4+ and SO42- contents had positive correlations with the silt and clay ratio in transported sediment but negative correlations with the sand ratio. These results provide a better understanding of the transport processes and can be used to develop equations to predict the transport of mineral-leaching chemicals in rare-earth tailings, which can provide a scientific foundation for erosion control and soil management in rare-earth tailing regions in southern China.

Investigation results on water quality and volume of flowing-in water to the Yotsugi slag heap site. 2

International Nuclear Information System (INIS)

Naganuma, Masaki; Taki, Tomihiro; Takimoto, Sadao; Makita, A.

2000-05-01

Mining water flowing into the Yotsugi slag heap site at the Ningyo-toge Environment Technical Center is exhausted to a common river after carrying out the treatment of uranium and radium in the mining water at the previously settled mining water treatment facility and confirming it to be less than management target value on the river water within the site boundary regulated by the agreement on environmental conservation with Okayama prefecture and Kami-saihara mura. In order to elucidate some required treatment on every water system flowing-in the heap site as a part of reduction of flowing volume on taking action of the heap site, an investigation on its water quality and volume was carried out. As a result, it was confirmed on water quality that uranium values of every river were all less than their target values but radium values of them were all over their target values which necessitated conventional water treatment. And, on water volume, it was confirmed that flowing water volume from the exposed excavation site was reduced about 40% in comparison with same rain-fall before removing from rain water. (G.K.)

An instrumented leach column for the study of sulphide oxidation in waste heaps

International Nuclear Information System (INIS)

Lowson, R.T.; Sarbutt, J.V.

1985-05-01

The construction, commissioning and first year of operation of a large scale, instrumented leach column are described. The column material was sulphidic mine overburden. Monitored parameters included matrix potential, temperature, redox potential, dissolved oxygen, pore space gas, water addition and drainage, together with pH, Cd, Cu, Fe, Ni, Zn, Cl - , F - , SO 4 2- and PO 4 3- in the effluent

Practice of the counter-current trickle leaching of uranium ore by refreshed liquor of bacterial oxidation

International Nuclear Information System (INIS)

Chen Shian; Huang Xiangfu; Fan Baotuan

1995-01-01

The uranium ore of the Mine No. 753 is a high-silicate type primary one, in which the tetravalent uranium accounts for 85%, and the uranium grade is in the range of 0.36% to 0.442%. To reduce the engineering investment and the operating cost a four-stage counter-current trickle leaching pilot-plant test was carried out with the leaching time 50 days and acid consumption 38 kg per ton of ore, and the recovery of more than 95% was obtained. Using the counter-current trickle leaching mode and controlling the limit concentration of the harmful matters in the bacterial leaching liquor, the latter can be effectively oxidized by the synchronical regeneration. A trickle leaching comparative test of 25 ton ore single heap also gave a good result of more than 95% in extraction rate, and 30% acid consumption was saved and the 2.0% pyrolusite (containing MnO 2 40%) was eliminated. This process is feasible in technology and worth-while in economy for treating the uranium ore of Mine No. 753, and provides a new method of uranium ore trickle leaching

Radionuclide release from simulated waste material after biogeochemical leaching of uraniferous mineral samples

International Nuclear Information System (INIS)

Williamson, Aimee Lynn; Caron, François; Spiers, Graeme

2014-01-01

Biogeochemical mineral dissolution is a promising method for the released of metals in low-grade host mineralization that contain sulphidic minerals. The application of biogeochemical mineral dissolution to engineered leach heap piles in the Elliot Lake region may be considered as a promising passive technology for the economic recovery of low grade Uranium-bearing ores. In the current investigation, the decrease of radiological activity of uraniferous mineral material after biogeochemical mineral dissolution is quantified by gamma spectroscopy and compared to the results from digestion/ICP-MS analysis of the ore materials to determine if gamma spectroscopy is a simple, viable alternative quantification method for heavy nuclides. The potential release of Uranium (U) and Radium-226 ( 226 Ra) to the aqueous environment from samples that have been treated to represent various stages of leaching and passive closure processes are assessed. Dissolution of U from the solid phase has occurred during biogeochemical mineral dissolution in the presence of Acidithiobacillus ferrooxidans, with gamma spectroscopy indicating an 84% decrease in Uranium-235 ( 235 U) content, a value in accordance with the data obtained by dissolution chemistry. Gamma spectroscopy data indicate that only 30% of the 226 Ra was removed during the biogeochemical mineral dissolution. Chemical inhibition and passivation treatments of waste materials following the biogeochemical mineral dissolution offer greater protection against residual U and 226 Ra leaching. Pacified samples resist the release of 226 Ra contained in the mineral phase and may offer more protection to the aqueous environment for the long term, compared to untreated or inhibited residues, and should be taken into account for future decommissioning. - Highlights: • Gamma counting showed an 84% decrease in 235 U after biogeochemical mineral leaching. • Chemical digestion/ICP-MS analysis also showed an 84% decrease in total U. • Over

Mining and processing of uranium ores in the USSR

International Nuclear Information System (INIS)

Laskorin, B.N.; Mamilov, V.A.; Korejsho, Yu.A.

1983-01-01

Experience gained in uranium ore mining by modern methods in combination with underground and heap leaching is summarized. More intensive processing of low-grade ores has been achieved through the use of autoclave leaching, sorptive treatment of thick pulps, extractive separation of pure uranium compounds, automated continuous sorption devices of high efficiency for processing the underground- and heap-leaching liquors, natural and mine water, and recovery of molybdenum, vanadium, scandium, rare earths and phosphate fertilizers from low-grade ores. Production of ion-exchangers and extractants has been developed and processes for concomitant recovery of copper, gold, ionium, tungsten, caesium, zirconium, tantalum, nickel and cobalt have been designed. (author)

Vertical Object Layout and Compression for Fixed Heaps

Science.gov (United States)

Titzer, Ben L.; Palsberg, Jens

Research into embedded sensor networks has placed increased focus on the problem of developing reliable and flexible software for microcontroller-class devices. Languages such as nesC [10] and Virgil [20] have brought higher-level programming idioms to this lowest layer of software, thereby adding expressiveness. Both languages are marked by the absence of dynamic memory allocation, which removes the need for a runtime system to manage memory. While nesC offers code modules with statically allocated fields, arrays and structs, Virgil allows the application to allocate and initialize arbitrary objects during compilation, producing a fixed object heap for runtime. This paper explores techniques for compressing fixed object heaps with the goal of reducing the RAM footprint of a program. We explore table-based compression and introduce a novel form of object layout called vertical object layout. We provide experimental results that measure the impact on RAM size, code size, and execution time for a set of Virgil programs. Our results show that compressed vertical layout has better execution time and code size than table-based compression while achieving more than 20% heap reduction on 6 of 12 benchmark programs and 2-17% heap reduction on the remaining 6. We also present a formalization of vertical object layout and prove tight relationships between three styles of object layout.

Status Report from Yugoslavia [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Bunji, B [Institute for Technology of Nuclear and Other Raw Materials, Belgrade, Yugoslavia (Serbia)

1967-06-15

Full text: The greater part of our activities is connected with the problem of extracting uranium from low-grade ores. In this paper, a brief review of the most important recent developments will be presented. In this connection, it may be useful to determine the definition of low-grade ores. This term can be applied to ore from which the uranium content cannot be extracted under normal economic conditions. Thus this term can be applied to uranium-bearing material with a uranium content of no more than 0. 05%. But, in general, it could be said that there is a very large range of uranium content where uranium extraction may not be economic for such different reasons as; (a) the size or other facts in connection with the orebodies themselves; (b) refractory ore; or (c) other local conditions. During research on the treatment of low-grade ore from the deposit at Gabrovnica (Stara Planina, Yugoslavia) it became apparent that an alkaline leaching process would have to be carried out. The treatment of this granitic type of ore causes no particular difficulties. The required temperature is about 90{sup o}C. The retention time in the leaching stage is from 4 to 12 hours. Sodium carbonate consumption is not higher than 15 kg/t of ore. Pachuca-type leaching shows satisfactory maintenance and processing costs. At Kalna uranium precipitation by means of hydrogen pressure reduction has been developed, and is being developed and investigated in full-scale operation. Details of the process were published in Geneva in 1963. On the basis of the experience gained from full-scale operation, many refinements and cost-saving changes have been made. A normal steel wire screen used as a catalyst carrier shows a very good improvement over free-moving UO{sub 2} as catalyst. In large-scale operation (200 t/d), after the precipitation of uranium the barren solution content is about 1 g U/m{sup 3}. The content of the pregnant solution is of the order of 300-600 g/m{sup 3}. Recycling the

Laboratory studies on leaching of low grade uranium ores and treatment of low level liquid waste generated by leaching experiments

International Nuclear Information System (INIS)

Palabrica, O.T.; Antonino, E.J.; Caluag, L.A.; Villamater, D.

1980-07-01

Acid leaching experiments of preconcentrated uranium ore were carried out at a pulp density of 50% solids, using sulfuric acid with sodium chlorate as oxidant. The different leaching parameters considered in this work were temperature, oxidant level and leaching time. In the experimental procedure, the concentration of oxidant and the temperature were varied to determine how they affect the leaching process. Experimental results are illustrated in tabulated form for better interpretation. Uranium analyses were done by fluorimetric and delayed-neutron activation analysis. An anion exchange method using Dowex 1 x 8, 200-400 mesh (Cl - ) was used in treating the low-level liquid waste generated by leaching experiments. The purpose of this treatment was to minimize radioactive contamination in the waste materials and also to recover some of the uranium left in the liquid waste. (author)

Extraction of uranium from anomaly ores no 1,6,8 in salt domes of Bandar Abbas region using column leaching by seawater in sulfuric acid medium

International Nuclear Information System (INIS)

Fatemi, K.

2003-01-01

Column leaching is one of the experimental methods which is used for identifying the specifications of uranium ores. From the efficiency point of view, the process has some complications and usually it is applied in parallel with the conventional leaching process in order to facilitate of finding an appropriate design and operational method, to be applicable in an large practical scale. In this research work, at the first stage, the existed free chlorine in the samples was washed out using seawater. Then, in a process of acid leaching with seawater and sulfuric acid by the use of the column leaching was applied. The results show that the maximum of 85% of uranium from the ore of Anomali ≠1 is extracted. The extra residual of the used acid dose not react with the uranium and therefore it will increase the free acidity of the leach liquor. In Anomali ≠6, the extraction efficiency of uranium is 75%, while in Anomali ≠8, using 30 periods of leaching, the efficiency is 81%. However, the maximum efficiency achievement has to be avoided by the non-economical circumstances. Based on some comparisons, it is shown that the presence of chlorine in ore will affect the efficiency. The capability of s eawater i n uranium extraction from salted, compared with the n ormal or sweat water h as some advantages. These include: reduction of the operational period, less acid consumption, and reduction in the ore leaching costs. Thus, the heap leaching industry is believed to be a valuable and economical method for uranium extraction, where the needs of utilizing the complicated technical facilities can be reduced. The present work is the first research project on the uranium extraction and concentration in solution containing chlorine. Our experimental results can provide a valuable pattern for the heap leaching of uranium ores design from arches shaped in the region Bandar Abbas

Successful approaches. Sports stars and HEAPS.

Science.gov (United States)

1996-01-01

In western Samoa, football stars are being used in the fight against acquired immunodeficiency syndrome (AIDS). Originally recruited by Palanitina Toelupe, chief health educator of the Health Education and Promotion Section (HEAPS), to assist with an anti-smoking campaign, the players became sensitized to issues regarding AIDS and agreed to visit high schools where they could urge young people to "Learn the Facts (about AIDS) and Pass the Word." With assistance from the SPC, HEAPS produced and broadcast radio and TV spots featuring the athletes; a poster was printed and distributed. Sports stars travel regionally and internationally; those with knowledge of AIDS and unsafe sex behavior can reinforce responsible sexual behavior among their teammates. Sports people should be targeted for AIDS and sexually transmitted disease (STD) education and prevention.

Heap leaching of clay ish uranium ores; Lixiviacion estatica de minerales arcillosos de uranio

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, E; Sedano, A

1973-07-01

This paper describes an experimental facility, built near El Lobo mine. In it we study the beneficiation of low-grade uranium ore. The mineral has a great amount of clay and fines. The flow-sheet used has four steps: head leaching, ph-ajustement, ion-exchange and participation. We show, also, the most interesting results. (Author)

Polonium (210Po) and uranium (234U, 238U) in water, phosphogypsum and their bioaccumulation in plants around phosphogypsum waste heap at Wislinka (nothern Poland)

International Nuclear Information System (INIS)

Skwarzec, B.; Borylo, A.; Kosinska, A.; Radzajewska, S.

2010-01-01

The principal sources of polonium and uranium radionuclides the Wislinka area waste dump are phosphorites and phosphogypsum produced by the Phosphoric Fertilizers Industry of Gdansk. The values of uranium and polonium concentration in water with immediate surroundings of waste heap are considerably higher than in the waters of the Martwa Wisla river. The activity ratio 234 U/ 238 U is approximately about one in the phosphogypsum (0.97±0.06 and 0.99±0.04) and in the water of a retention reservoir and a pumping station (0.92±0.01 and 0.99±0.04), while in the water from the Martwa Wisla river is slightly higher than one (1.00±0.07 and 1.06±0.02). The leaching process of uranium and polonium from the phosphogypsum waste heap is responsible for the maximum uranium concentration (1097±6 μg·dm -3 and 1177±6 μg·dm -3 ) and the high 210 Po concentration (131.4±0.9 mBq·dm -3 and 165.7±1.4 mBq·dm -3 ) in the retention reservoir. The major source of polonium and uranium in plants are wet and dry atmospheric falls gathering soil and air dust from the phosphogypsum waste dump and root system. The highest uranium and polonium concentrations were found in older part of grasses (yellow oatgrass, meadow foxtail, moneywort), exposed to atmospheric falls for a long time. The maximum concentrations of 210 Po were characterized for samples of plant root collected at the retention reservoir (150.50±4.97 and 108.55±3.95 Bq·kg -1 dry mass). Polonium and uranium concentrations in water samples of the Martwa Wisla river are relatively low in comparison with the value in the retention reservoir and pumping station near the phosphogypsum waste heap. This suggests that the radionuclides could be leached from the dumping site to the surrounding environment. (authors)

Mineral-leaching chemical transport with runoff and sediment from severely eroded rare-earth tailings in southern China

Directory of Open Access Journals (Sweden)

H. Lu

2017-08-01

Full Text Available Rare-earth mining has led to severe soil erosion in southern China. Furthermore, the presence of the mineral-leaching chemical ammonium sulfate in runoff and sediment poses a serious environmental threat to downstream water bodies. In this paper, the characteristics of mineral-leaching chemicals in surface soil samples collected in the field were studied. In addition, NH4+ and SO42− transport via soil erosion was monitored using runoff and sediment samples collected during natural rainfall processes. The results demonstrated that the NH4+ contents in the surface sediment deposits increased from the top of the heap (6.56 mg kg−1 to the gully (8.23 mg kg−1 and outside the tailing heap (13.03 mg kg−1. The contents of SO42− in the different locations of the tailing heaps ranged from 27.71 to 40.33 mg kg−1. During typical rainfall events, the absorbed NH4+ concentrations (2.05, 1.26 mg L−1 in runoff were significantly higher than the dissolved concentrations (0.93, 1.04 mg L−1, while the absorbed SO42− concentrations (2.87, 1.92 mg L−1 were significantly lower than the dissolved concentrations (6.55, 7.51 mg L−1. The dissolved NH4+ and SO42− concentrations in runoff displayed an exponentially decreasing tendency with increasing transport distance (Y = 1. 02 ⋅ exp( − 0. 00312X; Y = 3. 34 ⋅ exp( − 0. 0185X. No clear trend with increasing distance was observed for the absorbed NH4+ and SO42− contents in transported sediment. The NH4+ and SO42− contents had positive correlations with the silt and clay ratio in transported sediment but negative correlations with the sand ratio. These results provide a better understanding of the transport processes and can be used to develop equations to predict the transport of mineral-leaching chemicals in rare-earth tailings, which can provide a scientific foundation for erosion control and soil management in rare

Residues leaching from 'Factory of barren ores'

International Nuclear Information System (INIS)

Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

2012-01-01

The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

Ball Milling Treatment of Black Dross for Selective Dissolution of Alumina in Sodium Hydroxide Leaching

OpenAIRE

Thi Thuy Nhi Nguyen; Man Seung Lee; Thi Hong Nguyen

2018-01-01

A process consisting of ball milling followed by NaOH leaching was developed to selectively dissolve alumina from black dross. From the ball milling treatment, it was found that milling speed greatly affected the leaching behavior of silica and the oxides of Ca, Fe, Mg, and Ti present in dross. The leaching behavior of the mechanically activated dross was investigated by varying NaOH concentration, leaching temperature and time, and pulp density. In most of the leaching conditions, only alumi...

Waste water treatment of CO2+O2 in-situ leaching uranium

International Nuclear Information System (INIS)

Xu Lechang; Liu Naizhong; Du Zhiming; Wang Hongying

2012-01-01

An in-situ leaching uranium mine located in Northern China uses CO 2 +O 2 leaching process to leach uranium. The consumption of industrial reagent and water, and generation and discharge of waste water are minimized by comprehensive waste water treatment technology with process water recycle, reverse osmosis and natural evaporation. The process water of the mine that can be recycled and reused includes barren fluid, solution washing loaded resin, precipitating mother solution and filtered liquor of yellow cake. Solution regenerating barren resin is treated by reverse osmosis. Concentrated water from reverse osmosis and solution washing barren resin are naturally evaporated. (authors)

Deviations in the Zipf and Heaps laws in natural languages

Science.gov (United States)

Bochkarev, Vladimir V.; Lerner, Eduard Yu; Shevlyakova, Anna V.

2014-03-01

This paper is devoted to verifying of the empirical Zipf and Hips laws in natural languages using Google Books Ngram corpus data. The connection between the Zipf and Heaps law which predicts the power dependence of the vocabulary size on the text size is discussed. In fact, the Heaps exponent in this dependence varies with the increasing of the text corpus. To explain it, the obtained results are compared with the probability model of text generation. Quasi-periodic variations with characteristic time periods of 60-100 years were also found.

Deviations in the Zipf and Heaps laws in natural languages

International Nuclear Information System (INIS)

Bochkarev, Vladimir V; Lerner, Eduard Yu; Shevlyakova, Anna V

2014-01-01

This paper is devoted to verifying of the empirical Zipf and Hips laws in natural languages using Google Books Ngram corpus data. The connection between the Zipf and Heaps law which predicts the power dependence of the vocabulary size on the text size is discussed. In fact, the Heaps exponent in this dependence varies with the increasing of the text corpus. To explain it, the obtained results are compared with the probability model of text generation. Quasi-periodic variations with characteristic time periods of 60-100 years were also found

Defective zoospore encystment and suppressed cyst germination of Phytophthora palmivora caused by transient leaching treatments

NARCIS (Netherlands)

Dijksterhuis, J; Deacon, J W

2003-01-01

The behaviour of encysting zoospores of Phytophthora palmivora during leaching conditions was studied. Zoospores encysted and germinated successfully on polycarbonate membranes after mechanical agitation. Transient (10 min) leaching treatments with nutrient-free buffer underneath the membranes

Event heap: a coordination infrastructure for dynamic heterogeneous application interactions in ubiquitous computing environments

Science.gov (United States)

Johanson, Bradley E.; Fox, Armando; Winograd, Terry A.; Hanrahan, Patrick M.

2010-04-20

An efficient and adaptive middleware infrastructure called the Event Heap system dynamically coordinates application interactions and communications in a ubiquitous computing environment, e.g., an interactive workspace, having heterogeneous software applications running on various machines and devices across different platforms. Applications exchange events via the Event Heap. Each event is characterized by a set of unordered, named fields. Events are routed by matching certain attributes in the fields. The source and target versions of each field are automatically set when an event is posted or used as a template. The Event Heap system implements a unique combination of features, both intrinsic to tuplespaces and specific to the Event Heap, including content based addressing, support for routing patterns, standard routing fields, limited data persistence, query persistence/registration, transparent communication, self-description, flexible typing, logical/physical centralization, portable client API, at most once per source first-in-first-out ordering, and modular restartability.

Reagents and fractions impact on sulphide ore heap bioleaching at Smolnik mine

Science.gov (United States)

Oros, L. M.; Zavada, J.

2017-10-01

Mine Smolnik is one of the oldest sulphide ore mines in Europe and it is also an important part of bioleaching development. This paper follows previous attempts to extract residual metals from nearby heaps via variations in bioleaching reagents with regard to recent findings and needs in the related industry. Furthermore, economic and process relations between reagents and chosen heap fractions were also investigated in this case study.

Transient response in granular bounded heap flows

Science.gov (United States)

Xiao, Hongyi; Ottino, Julio M.; Lueptow, Richard M.; Umbanhowar, Paul B.

2017-11-01

Heap formation, a canonical granular flow, is common in industry and is also found in nature. Here, we study the transition between steady flow states in quasi-2D bounded heaps by suddenly changing the feed rate from one fixed value to another. During the transition, in both experiments and discrete element method simulations, an additional wedge of flowing particles propagates over the rising free surface. The downstream edge of the wedge - the wedge front - moves downstream with velocity inversely proportional to the square root of time. An additional longer duration transient process continues after the wedge front reaches the downstream wall. The transient flux profile during the entire transition is well modeled by a diffusion-like equation derived from local mass balance and a local linear relation between the flux and the surface slope. Scalings for the transient kinematics during the flow transitions are developed based on the flux profiles. Funded by NSF Grant CBET-1511450.

Extremophiles in Mineral Sulphide Heaps: Some Bacterial Responses to Variable Temperature, Acidity and Solution Composition

Directory of Open Access Journals (Sweden)

Helen R. Watling

2015-07-01

Full Text Available In heap bioleaching, acidophilic extremophiles contribute to enhanced metal extraction from mineral sulphides through the oxidation of Fe(II and/or reduced inorganic sulphur compounds (RISC, such as elemental sulphur or mineral sulphides, or the degradation of organic compounds derived from the ore, biota or reagents used during mineral processing. The impacts of variable solution acidity and composition, as well as temperature on the three microbiological functions have been examined for up to four bacterial species found in mineral sulphide heaps. The results indicate that bacteria adapt to sufficiently high metal concentrations (Cu, Ni, Co, Zn, As to allow them to function in mineral sulphide heaps and, by engaging alternative metabolic pathways, to extend the solution pH range over which growth is sustained. Fluctuating temperatures during start up in sulphide heaps pose the greatest threat to efficient bacterial colonisation. The large masses of ores in bioleaching heaps mean that high temperatures arising from sulphide oxidation are hard to control initially, when the sulphide content of the ore is greatest. During that period, mesophilic and moderately thermophilic bacteria are markedly reduced in both numbers and activity.

Ni, Co, and Cr contents in the soil and in some plants of Dobsina asbestos heaps

Energy Technology Data Exchange (ETDEWEB)

Banasova, V

1978-01-01

Results of analyses of substrates of heaps after mining and working of asbestos as well as of two plants viz. Melilotus officinalis Lam. and Calamagrostis epigeios Roth. for Ni, Co and Cr. Ni and Co concentrations in the analyzed plants and heap substrates were found to be higher than in common soils and in plants growing at unsophisticated localities. The values ascertained are at the same time lower than in soils and plants on serpentines. There were very low Cr contents in substrates of the studied heaps. On the contrary, in both analyzed plant species Cr concentration was found to be much higher than in the investigated heap substrates. At that locality Melilotus officinalis and Calamagrostis epigeios appear to be concentrators of chromium.

The general solution of a Nim-heap game

Institute of Scientific and Technical Information of China (English)

宋林森; 卢澎涛

2010-01-01

As a combinatorial one,the game Nim turns out to be extremely useful in certain types of combinatorial game analysis.It has given the general solution of the game a Nim-heap game and the result has proved true.

Radioactivity measurements in the vicinity of the mine waste heap at Crossen and radiation dose assessment

International Nuclear Information System (INIS)

Kulzer, R.

1998-01-01

The radiation dose to the population living in the vicinity of the mine waste heap is assessed. The measurements carried out were to verify the dose relevance of ambient radioactivity on site, in particular the ingestion and inhalation pathways and the external exposure pathways. The nuclide Pb-210 was used as an indicator because of its large dose factor for assessment of ingestion and its airborne dispersion as an Rn-222 daughter product. The waste heap material releases large quantities of this nuclide. Ingestion of radioactivity from the waste heap may be caused by wind-borne erosion and activity deposition on plants in the area. Therefore, the specific activities of Pb-210 and Ra-226 have been measured in soil and plant specimens sampled at various distances from the waste heap. (orig./CB) [de

Assessment of metal contaminations leaching out from recycling plastic bottles upon treatments.

Science.gov (United States)

Cheng, Xiaoliang; Shi, Honglan; Adams, Craig D; Ma, Yinfa

2010-08-01

Heavy metal contaminants in environment, especially in drinking water, are always of great concern due to their health impact. Due to the use of heavy metals as catalysts during plastic syntheses, particularly antimony, human exposure to metal release from plastic bottles has been a serious concern in recent years. The aim and scope of this study were to assess metal contaminations leaching out from a series of recycling plastic bottles upon treatments. In this study, leaching concentrations of 16 metal elements were determined in 21 different types of plastic bottles from five commercial brands, which were made of recycling materials ranging from no. 1 to no. 7. Several sets of experiments were conducted to study the factors that could potentially affect the metal elements leaching from plastic bottles, which include cooling with frozen water, heating with boiling water, microwave, incubating with low-pH water, outdoor sunlight irradiation, and in-car storage. Heating and microwave can lead to a noticeable increase of antimony leaching relative to the controls in bottle samples A to G, and some even reached to a higher level than the maximum contamination level (MCL) of the US Environmental Protection Agency (USEPA) regulations. Incubation with low-pH water, outdoor sunlight irradiation, and in-car storage had no significant effect on antimony leaching relative to controls in bottle samples A to G, and the levels of antimony leaching detected were below 6 ppb which is the MCL of USEPA regulations. Cooling had almost no effect on antimony leaching based on our results. For the other interested 15 metal elements (Al, V, Cr, Mn, Co, Ni, Cu, As, Se, Mo, Ag, Cd, Ba, Tl, Pb), no significant leaching was detected or the level was far below the MCL of USEPA regulations in all bottle samples in this study. In addition, washing procedure did contribute to the antimony leaching concentration for polyethylene terephthalate (PET) bottles. The difference of antimony leaching

Potential for leaching of arsenic from excavated rock after different drying treatments.

Science.gov (United States)

Li, Jining; Kosugi, Tomoya; Riya, Shohei; Hashimoto, Yohey; Hou, Hong; Terada, Akihiko; Hosomi, Masaaki

2016-07-01

Leaching of arsenic (As) from excavated rock subjected to different drying methods is compared using sequential leaching tests and rapid small-scale column tests combined with a sequential extraction procedure. Although the total As content in the rock was low (8.81 mg kg(-1)), its resulting concentration in the leachate when leached at a liquid-to-solid ratio of 10 L kg(-1) exceeded the environmental standard (10 μg L(-1)). As existed mainly in dissolved forms in the leachates. All of the drying procedures applied in this study increased the leaching of As, with freeze-drying leading to the largest increase. Water extraction of As using the two tests showed different leaching behaviors as a function of the liquid-to-solid ratio, and achieved average extractions of up to 35.7% and 25.8% total As, respectively. Dissolution of As from the mineral surfaces and subsequent re-adsorption controlled the short-term release of As; dissolution of Fe, Al, and dissolved organic carbon played important roles in long-term As leaching. Results of the sequential extraction procedure showed that use of 0.05 M (NH4)2SO4 underestimates the readily soluble As. Long-term water extraction removed almost all of the non-specifically sorbed As and most of the specifically sorbed As. The concept of pollution potential indices, which are easily determined by the sequential leaching test, is proposed in this study and is considered for possible use in assessing efficacy of treatment of excavated rocks. Copyright © 2016 Elsevier Ltd. All rights reserved.

Secondary wastes and treatment of effluents from leaching of uranium from soils

International Nuclear Information System (INIS)

Ally, M.R.; Wilson, J.H.; Francis, C.W.

1993-01-01

The Department of Energy's Feed Materials and Production Center at Fernald, Ohio has over two million cubic meters of soil contaminated with Uranium which must be cleaned. Soil characterization studies show that Uranium is unevenly distributed between the clay, sand and silt fractions. This paper examines the option of using leaching agents to remove Uranium from the soil and the treatment of secondary wastes. Results of the effects of various leachants in removing Uranium and the complications of co-leaching minerals/organic matter that are important for maintaining soil integrity and structure shall be discussed. Candidate leachants must remove the Uranium level below 35pCi/g of soil and produce a secondary waste that is amenable to on-site treatment at reasonable cost

Reverse osmosis treatment in CO_2 + O_2 to the application of the in-situ leaching of uranium

International Nuclear Information System (INIS)

Ruan Zhilong; Li Xilong; Yang Shaowu

2014-01-01

Advantages and disadvantages of various groundwater management methods, combined with CO_2 + O_2 characteristics of in situ leaching uranium mining process, use reverse osmosis wastewater treatment technology, has carried on the laboratory test, field condition test and industrial test. Obtained by indoor experiment and field conditions for Cl"- ion concentration variation characteristics; Reverse osmosis treatment effect of wastewater is verified by industrial test, obtained the technical parameters and consumption data, as well as the leaching liquid and adsorption tail liquid pH, SO_4"2"-; Cl"- in the plasma concentration monitoring, and further prove that the reverse osmosis treatment technology is suitable for in-situ leaching of uranium in CO_2 + O_2 in wastewater treatment. (authors)

Reducing Heavy Metal Element from Coal Bottom Ash by Using Citric Acid Leaching Treatment

Directory of Open Access Journals (Sweden)

Yahya Ahmad Asyari

2017-01-01

Full Text Available Coal ash is the residue that is produced during coal combustion for instance fly ash, bottom ash or boiler slag which was primarily produced from the combustion of coal. With growth in coal burning power station, huge amount of coal bottom ash (CBA considered as hazardous material which are normally disposed in an on-site disposal system without any commercialization purpose. Previous researchers have studied the extraction of silica from agricultural wastes such as palm ash and rice husk ash (RHA and CBA by using leaching treatment method. In this study, the weaker acid, citric acid solution was used to replace the strong acid in leaching treatment process. Result showed that the heavy metal content such as Copper (Cu, Zinc (Zn and Lead (Pb can be decrease. Meanwhile the silica can be extracted up to 44% from coal bottom ash using citric acid leaching treatment under the optimum reaction time of 60 minutes with solution temperature of 60°C and concentration of citric acid more than 2%.

The copper spoil heap Knappenberg, Austria, as a model for metal habitats – Vegetation, substrate and contamination

Energy Technology Data Exchange (ETDEWEB)

Adlassnig, Wolfram; Weiss, Yasmin S. [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); Sassmann, Stefan [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); University of Exeter, College of Life and Environmental Sciences, Biosciences, Stocker Road, Exeter EX4 4QD (United Kingdom); Steinhauser, Georg [Leibniz University Hannover, Institute of Radioecology and Radiation Protection, Herrenhäuser Straße 2, D30419 Hannover (Germany); Hofhansl, Florian [University of Vienna, Department of Microbiology and Ecosystem Science, Althanstraße 14, A-1090 Vienna (Austria); Instituto Nacional de Pesquisas da Amazônia, Coordenação de Dinâmica Ambiental, Manaus (Brazil); Baumann, Nils [Helmholtz-Zentrum Dresden-Rossendorf, Division of Biogeochemistry, Bautzner Landstraße 400, D-01328 Dresden (Germany); Lichtscheidl, Irene K. [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria); Lang, Ingeborg, E-mail: ingeborg.lang@univie.ac.at [University of Vienna, Core Facility Cell Imaging and Ultrastructure Research, Althanstraße 14, A-1090 Vienna (Austria)

2016-09-01

Historic mining in the Eastern Alps has left us with a legacy of numerous spoil heaps hosting specific, metal tolerant vegetation. Such habitats are characterized by elevated concentrations of toxic elements but also by high irradiation, a poorly developed substrate or extreme pH of the soil. This study investigates the distribution of vascular plants, mosses and lichens on a copper spoil heap on the ore bearing Knappenberg formed by Prebichl Layers and Werfener Schist in Lower Austria. It serves as a model for discriminating between various ecological traits and their effects on vegetation. Five distinct clusters were distinguished: (1) The bare, metal rich Central Spoil Heap was only colonised by highly resistant specialists. (2) The Northern and (3) Southern Peripheries contained less copper; the contrasting vegetation was best explained by the different microclimate. (4) A forest over acidic bedrock hosted a vegetation overlapping with the periphery of the spoil heap. (5) A forest over calcareous bedrock was similar to the spoil heap with regard to pH and humus content but hosted a vegetation differing strongly to all other habitats. Among the multiple toxic elements at the spoil heap, only Cu seems to exert a crucial influence on the vegetation pattern. Besides metal concentrations, irradiation, humidity, humus, pH and grain size distribution are important for the establishment of a metal tolerant vegetation. The difference between the species poor Northern and the diverse Southern Periphery can be explained by the microclimate rather than by the substrate. All plant species penetrating from the forest into the periphery of the spoil heap originate from the acidic but not from the calcareous bedrock. - Highlights: • Strong impact on plant diversity by isolation and extreme abiotic conditions • Both, microclimate and substrate explain species distribution. • Increased cellular metal tolerance of plants from the Central Spoil Heap • Among toxic elements

Microbial degradation of cyanide from gold metallurgical plants utilizing P. fluorecens

International Nuclear Information System (INIS)

Restrepo, Oscar Jaime; Montoya, Carlos Arturo; Munoz, Nury Alexandra

2005-01-01

Sodium cyanide is traditionally used in chemical metallurgy to obtain precious metals (gold and silver). Cyanide produces damages because of its toxicity and breath cell inhibition. Here we try a biotechnological process to degrade cyanide with P. fluorescens obtained by cyanide heap leaching process in gold metallurgy in Segovia, Colombia. In Colombia cyanide heap-leaching process in gold metallurgy is not controlled and cyanide is used excessively. It means that great quantities of sodium cyanide are lost in sands and in wastewater. Toxicity tests made by D. pulex show less than 54 ppm of cyanide is enough to kill them. Traditional treatments to cyanide degradation are useful and normal but they are expensive. Microbiological process eliminates cyanide successfully and cheap

Long term growth of crop plants on experimental plots created among slag heaps.

Science.gov (United States)

Halecki, Wiktor; Klatka, Sławomir

2018-01-01

Suppression of plant growth is a common problem in post-mining reclaimed areas, as coarse texture of soils may increase nitrate leaching. Assessing feasibility of using solid waste (precipitated solid matter) produced by water and sewage treatment processes in field conditions is very important in mine soil reclamation. Our work investigated the possibility of plant growth in a degraded site covered with sewage-derived sludge material. A test area (21m × 18m) was established on a mine soil heap. Experimental plant species included Camelina sativa, Helianthus annuus, Festuca rubra, Miscanthus giganteus, Amaranthus cruentus, Brassica napus, Melilotus albus, Beta vulgaris, and Zea mays. ANOVA showed sufficient water content and acceptable physical properties of the soil in each year and layer in a multi-year period, indicating that these species were suitable for phytoremediation purposes. Results of trace elements assays indicated low degree of contamination caused by Carbocrash waste material and low potential ecological risk for all plant species. Detrended correspondence analysis revealed that total porosity and capillary porosity were the most important variables for the biosolids among all water content related properties. Overall, crop plants were found useful on heavily degraded land and the soil benefited from their presence. An addition of Carbocrash substrate to mine soil improved the initial stage of soil reclamation and accelerated plant growth. The use of this substrate in phytoremediation helped to balance the content of nutrients, promoted plant growth, and increased plant tolerance to salinity. Sewage sludge-amended biosolids may be applied directly to agricultural soil, not only in experimental conditions. Copyright © 2017 Elsevier Inc. All rights reserved.

Research on the possibility of concentrating low-grade uranium ores by bacterial leaching. Part of a coordinated programme on the bacterial leaching of uranium ores

International Nuclear Information System (INIS)

Tataru, S.

1978-12-01

Effect of extraction reagents with solvents on the bacteria and the influence of eluants on the bacteria development was studied. To establish the effects of various solvents and eluants on the development of bacteria, on oxidizing capacity of Fe 2+ to Fe 3+ , and to study their influence on bacteria morphology, bacteria strains were contacted with Alamine 336, trioctylamine, LIX and nitric eluant. Bacteria development and the oxidizing ability of Fe 2+ to Fe 3+ were significantly inhibited and morphological changes of individuals in the bacteria population were found. The bacteria populations resulted from ores had a more decreased resistance as the bacteria culture was better selected by repeated inoculations and incubations. In case of the bacterial leaching in heap or in situ a periodical extraction with solvents is required in order to allow the bacteria population between successive extraction stage be remade

Fast heap transform-based QR-decomposition of real and complex matrices: algorithms and codes

Science.gov (United States)

Grigoryan, Artyom M.

2015-03-01

In this paper, we describe a new look on the application of Givens rotations to the QR-decomposition problem, which is similar to the method of Householder transformations. We apply the concept of the discrete heap transform, or signal-induced unitary transforms which had been introduced by Grigoryan (2006) and used in signal and image processing. Both cases of real and complex nonsingular matrices are considered and examples of performing QR-decomposition of square matrices are given. The proposed method of QR-decomposition for the complex matrix is novel and differs from the known method of complex Givens rotation and is based on analytical equations for the heap transforms. Many examples illustrated the proposed heap transform method of QR-decomposition are given, algorithms are described in detail, and MATLAB-based codes are included.

MR imaging of ore for heap bioleaching studies using pure phase encode acquisition methods

Science.gov (United States)

Fagan, Marijke A.; Sederman, Andrew J.; Johns, Michael L.

2012-03-01

Various MRI techniques were considered with respect to imaging of aqueous flow fields in low grade copper ore. Spin echo frequency encoded techniques were shown to produce unacceptable image distortions which led to pure phase encoded techniques being considered. Single point imaging multiple point acquisition (SPI-MPA) and spin echo single point imaging (SESPI) techniques were applied. By direct comparison with X-ray tomographic images, both techniques were found to be able to produce distortion-free images of the ore packings at 2 T. The signal to noise ratios (SNRs) of the SESPI images were found to be superior to SPI-MPA for equal total acquisition times; this was explained based on NMR relaxation measurements. SESPI was also found to produce suitable images for a range of particles sizes, whereas SPI-MPA SNR deteriorated markedly as particles size was reduced. Comparisons on a 4.7 T magnet showed significant signal loss from the SPI-MPA images, the effect of which was accentuated in the case of unsaturated flowing systems. Hence it was concluded that SESPI was the most robust imaging method for the study of copper ore heap leaching hydrology.

Coarsening of Faraday Heaps: Experiment, Simulation, and Theory

NARCIS (Netherlands)

Gerner, van H.J.; Robledo, Caballero G.A.; Meer, van der D.; Weele, van der J.P.; Hoef, van der M.A.

2009-01-01

When a layer of granular material is vertically shaken, the surface spontaneously breaks up in a landscape of small Faraday heaps that merge into larger ones on an ever increasing time scale. This coarsening process is studied in a linear setup, for which the average life span of the transient state

Hydrometallurgical treatment of copper smelter dusts. Desarsenification of leaching solutions

International Nuclear Information System (INIS)

Alguacil, F.J.; Magne, L.; Navarro, P.; Simpson, J.

1996-01-01

Copper smelter dusts contain along with this metal, which is amenable for its recovery, a number of other metals (especially arsenic) which are considered as toxic. Different alternatives have been proposed for the treatment of such metallurgical residues and among them Hydrometallurgy shows good perspectives for its application in this field. In the present work different hydrometallurgical processes proposed for the treatment of copper smelter dusts are described and evaluated together with different alternatives given for the Desarsenification of the leaching solutions. (Author) 36 refs

Heap: a highly sensitive and accurate SNP detection tool for low-coverage high-throughput sequencing data

KAUST Repository

Kobayashi, Masaaki

2017-04-20

Recent availability of large-scale genomic resources enables us to conduct so called genome-wide association studies (GWAS) and genomic prediction (GP) studies, particularly with next-generation sequencing (NGS) data. The effectiveness of GWAS and GP depends on not only their mathematical models, but the quality and quantity of variants employed in the analysis. In NGS single nucleotide polymorphism (SNP) calling, conventional tools ideally require more reads for higher SNP sensitivity and accuracy. In this study, we aimed to develop a tool, Heap, that enables robustly sensitive and accurate calling of SNPs, particularly with a low coverage NGS data, which must be aligned to the reference genome sequences in advance. To reduce false positive SNPs, Heap determines genotypes and calls SNPs at each site except for sites at the both ends of reads or containing a minor allele supported by only one read. Performance comparison with existing tools showed that Heap achieved the highest F-scores with low coverage (7X) restriction-site associated DNA sequencing reads of sorghum and rice individuals. This will facilitate cost-effective GWAS and GP studies in this NGS era. Code and documentation of Heap are freely available from https://github.com/meiji-bioinf/heap (29 March 2017, date last accessed) and our web site (http://bioinf.mind.meiji.ac.jp/lab/en/tools.html (29 March 2017, date last accessed)).

A Phase-Adaptive Garbage Collector Using Dynamic Heap Partitioning and Opportunistic Collection

Science.gov (United States)

Roh, Yangwoo; Kim, Jaesub; Park, Kyu Ho

Applications usually have their own phases in heap memory usage. The traditional garbage collector fails to match various application phases because the same heuristic on the object behavior is used throughout the entire execution. This paper introduces a phase-adaptive garbage collector which reorganizes the heap layout and adjusts the invocation time of the garbage collection according to the phases. The proposed collector identifies phases by detecting the application methods strongly related to the phase boundaries. The experimental results show that the proposed phase-adaptive collector successfully recognizes application phases and improves the garbage collection time by as much as 41%.

Uptake of Radium by Grass and Shrubs Grown on Mineral Heaps: A Preliminary Study

International Nuclear Information System (INIS)

Laili, Z.; Omar, M.; Yusof, M.A. Wahab; Ibrahim, M.Z.

2015-01-01

A preliminary study of the uptake of 226 Ra and 228 Ra by grass and shrubs grown on mineral heaps was carried out. Activity concentrations of 226 Ra and 228 Ra in grass and shrubs were measured using gamma spectrometry. The result showed that grass and shrubs grown on mineral heaps contained elevated levels of radium compared to grass and shrubs grown on normal soils. Thus, these plants might be used for phytoremediation of radium contaminated soil. (author)

Ore leaching processing for yellow cake production and assay of their uranium content by radiometric analysis

Energy Technology Data Exchange (ETDEWEB)

Abdel-Rahman, Mohamed A.E. [Nuclear Engineering Department, Military Technical College, Kobry El-Kobbah, Cairo (Egypt); El-Mongy, Sayed A. [Nuclear and Radiological Regularity Authority (ENRRA), Nasr City, Cairo (Egypt)

2018-01-17

In this study, Ore granite samples were collected from Gattar site for leashing of yellow cake. The process involves heap leaching of uranium through four main steps; size reduction, leaching, uranium purification, and finally precipitation and filtration. The separation process has been given in details and as flow chart. Gamma spectrometry based on HpGe detector and energy dispersive X-ray (EDX) were used to assay uranium content and activity before and after separation. The uranium weight percentage value as measured by EDX were found to be 40.5 and 67.5 % before and after purification respectively. The results of the calculations based on gamma measurements show high uranium activity and the uranium activity ratios values are 0.045 ± 4.9, 0.043 ± 4.7, and 0.046 ± 2.3 %, before purification, whereas these values were found to be 0.050 ± 3.3, 0.049 ± 3.3, and 0.050 ± 2.7 %, after purification, respectively. The results are discussed in details in the paper. (copyright 2018 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Multiphase simulation of mine waters and aqueous leaching processes

Directory of Open Access Journals (Sweden)

Pajarre Risto

2016-01-01

Full Text Available Managing of large amounts of water in mining and mineral processing sites remains a concern in both actively operated and closed mining areas. When the mining site with its metal or concentrate producing units is operational, the challenge is to find either ways for economical processing with maximum yields, while minimizing the environmental impact of the water usage and waste salt treatments. For safe closure of the site, the environmental control of possible drainage will be needed. For both challenges, the present-day multiphase process simulations tools can be used to provide improved accuracy and better economy in controlling the smooth and environmentally sound operation of the plant. One of the pioneering studies in using the multiphase thermodynamic software in simulation of hydrometallurgical processes was that of Koukkari et al. [1]. The study covered the use of Solgasmix equilibrium software for a number of practical acid digesters. The models were made for sulfuric acid treatments in titania pigment production and in NPK fertilizer manufacturing. During the past two decades the extensive data assessment has taken place particularly in geochemistry and a new versions of geochemical multiphase equilibrium software has been developed. On the other hand, there has been some progress in development of the process simulation software in all the aforementioned fields. Thus, the thermodynamic simulation has become a tool of great importance in development of hydrometallurgical processes. The presentation will cover three example cases of either true pilot or industrial systems including a South African acid mine water drainage treatment, hydrometallurgical extraction of rare earths from uranium leachate in Russia and a multistage process simulation of a Finnish heap leaching mine with its subsequent water treatment system.

The current state of the heaps in Rosicko-Oslavany coal-field and the possibilities of their utilization; Soucasny stav hald v Rosicko-oslavanskem uhelnem reviru a moznosti jejich vyuziti

Energy Technology Data Exchange (ETDEWEB)

Svoboda, M. [Univerzita Palackeho v Olomouci, Prirodovedecka fakulta, Katedra rozvojovych studii, 77146 Olomouc (Czech Republic)

2013-04-16

The purpose of the article is to assess the importance of heaps for the land Rosicko-Oslavany coal-field. The heap is an anthropogenic land-form resulting from the accumulation of mineral resources extracted from the land. The heap shows as an unusual geomorfophological shape, which does not belong to the environment at first glance. In many respects the heap acts as a barrier for the other development because the heap may contains a dangerous material or may be unstable because of wrong storage of the material. The heaps in studied region stem from the black coal mining. The totals of 11 heaps were discovered during the field reconnaissance. While the heap Jindrich has a good potential for the other use, the heap Kukla represents a burden for its nearest surroundings. (authors)

Diagnosis of the generation, harvesting and leached treatment of the Relleno Sanitario Rio Azul and proposal of technological alternatives for its improvement

International Nuclear Information System (INIS)

Rojas Gonzalez, Ileana

2007-01-01

An environmental diagnosis was conduced in the Relleno Sanitario Rio Azul to evaluate the state of the generation, the harvesting and the leached treatment system. Besides, the corrective measures for each case were determined. The physicochemical characterization of the leached generated has been established through the collection of historical analysis conduced and the implementation of an environmental monitoring plan. As a consequence of said characterization, it was concluded that the leached generated at present possesses the specific characteristics of backfills that are found in mature stage (methanogenic), to know: low relation DBO/DQO, slightly basic pH, low concentration of heavy metals and low biodegradability. Even so these liquids must be treated to fulfill the permissible maximum parameters that establish the Reglamento de Uso y Vertido de Aguas Residuales. A seasonal variation linked with the generation of leached was determined, by effects of infiltration, toward the mass of waste and the combination of pluvial water with leached, mainly due to the absence of adequate infrastructure and unfinished works. The amount of leached that was generated and that will be generated until year 2025 it was managed to consider by means of the modeling a hydric balance. The volume is significant and is due to adopt the respective sanitary measures to guarantee to long term the adapted treatment of the leached and the fulfillment of the effective legislation. A series of improvements are proposed to the leached treatment system that functions at present, as a consequence of the diagnosis carried out to achieve that the quality of the effluent treated comply with the parameters of poured established; such as: filtration of heavy particles, implementation of a physicochemical treatment and treatment of muds. (author) [es

Solidified structure and leaching properties of metallurgical wastewater treatment sludge after solidification/stabilization process.

Science.gov (United States)

Radovanović, Dragana Đ; Kamberović, Željko J; Korać, Marija S; Rogan, Jelena R

2016-01-01

The presented study investigates solidification/stabilization process of hazardous heavy metals/arsenic sludge, generated after the treatment of the wastewater from a primary copper smelter. Fly ash and fly ash with addition of hydrated lime and Portland composite cement were studied as potential binders. The effectiveness of the process was evaluated by unconfined compressive strength (UCS) testing, leaching tests (EN 12457-4 and TCLP) and acid neutralization capacity (ANC) test. It was found that introduction of cement into the systems increased the UCS, led to reduced leaching of Cu, Ni and Zn, but had a negative effect on the ANC. Gradual addition of lime resulted in decreased UCS, significant reduction of metals leaching and high ANC, due to the excess of lime that remained unreacted in pozzolanic reaction. Stabilization of more than 99% of heavy metals and 90% of arsenic has been achieved. All the samples had UCS above required value for safe disposal. In addition to standard leaching tests, solidificates were exposed to atmospheric conditions during one year in order to determine the actual leaching level of metals in real environment. It can be concluded that the EN 12457-4 test is more similar to the real environmental conditions, while the TCLP test highly exaggerates the leaching of metals. The paper also presents results of differential acid neutralization (d-AN) analysis compared with mineralogical study done by scanning electron microscopy and X-ray diffraction analysis. The d-AN coupled with Eh-pH (Pourbaix) diagrams were proven to be a new effective method for analysis of amorphous solidified structure.

MONITORING OF HEAPS USING VARIOUS TECHNOLOGIES

Directory of Open Access Journals (Sweden)

Helena Straková

2015-07-01

Full Text Available Coal heaps are frequently self-burning by definite environmental conditions, therefore thermal activity monitoring of these localities is important. For this purpose, data from terrestrial measurement or thermal infrared images are used. Subsurface coal fires monitored by terrestrial measurement by contact thermometers are time-consuming and dangerous because of landslides. That is a reason why coal fires are mostly monitored by thermal infrared images through remote sensing, i.e. satellite-borne or airborne data, which is much more suitable for thermal activity monitoring. The satellite data do not have sufficient geometric resolution (60 - 120m per pixel, aerial thermal data are accurate, but expensive. Unmanned aerial vehicles (UAV or better RPAS - remotely piloted aircraft systems can be solution – thermal images obtained by RPAS have good geometric resolution and can be used for small areas only and our case project areas are not so big. From economic point of view, low cost technology is preferred. The article describes opportunities of low-cost thermal infrared data, the use of RPAS (mapping by Microkopter system in thermal monitoring and photogrammetric tasks (coal heaps such as low cost aerial thermal mapping. The problems of planning and data acquisition are illustrated by creating an orthophoto. Theoretical preparation of data acquisition deals with RPAS Microkopter mission planning and operation. The obtained data are processed by several sets of software specially developed for close range aerial photogrammetry. The outputs are orthophoto images, digital elevation models and thermal map. As a bonus, low-cost aerial methods with small thermal camera are shown.

Leaching from waste incineration bottom ashes treated in a rotary kiln

DEFF Research Database (Denmark)

Hyks, Jiri; Nesterov, Igor; Mogensen, Erhardt

2011-01-01

Leaching from municipal solid waste incineration bottom ash treated in a rotary kiln was quantified using a combination of lab-scale leaching experiments and geochemical modelling. Thermal treatment in the rotary kiln had no significant effect on the leaching of Al, Ba, Ca, Mg, Si, Sr, Zn, sulfate...... the thermal treatment. Overall, rotary kiln thermal treatment of bottom ashes can be recommended to reduce the leaching of Cu, Pb, Cl and DOC; however, increased leaching of Cr and Mo should be expected....

Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment

International Nuclear Information System (INIS)

Xiu, Fu-Rong; Qi, Yingying; Zhang, Fu-Shen

2015-01-01

Highlights: • We report a novel process for recovering Au, Ag, and Pd from waste PCBs. • The effect of SCWO on the leaching of Au, Ag, and Pd in waste PCBs was studied. • SCWO was highly efficient for enhancing the leaching of Au, Ag, and Pd. • The optimum leaching parameters for Au, Ag, and Pd in iodine–iodide were studied. - Abstract: Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine–iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine–iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO + HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420 °C and 60 min for Au and Pd, and 410 °C and 30 min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO + HL)-treated PCBs with iodine–iodide system were leaching time of 120 min (90 min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10 g/mL (1:8 g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine–iodide leaching process

Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment

Energy Technology Data Exchange (ETDEWEB)

Xiu, Fu-Rong, E-mail: xiu_chem@hotmail.com [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Qi, Yingying [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350108 (China); Zhang, Fu-Shen [Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

2015-07-15

Highlights: • We report a novel process for recovering Au, Ag, and Pd from waste PCBs. • The effect of SCWO on the leaching of Au, Ag, and Pd in waste PCBs was studied. • SCWO was highly efficient for enhancing the leaching of Au, Ag, and Pd. • The optimum leaching parameters for Au, Ag, and Pd in iodine–iodide were studied. - Abstract: Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine–iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine–iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO + HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420 °C and 60 min for Au and Pd, and 410 °C and 30 min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO + HL)-treated PCBs with iodine–iodide system were leaching time of 120 min (90 min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10 g/mL (1:8 g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine–iodide leaching process.

Alkaline leaching of coal by the mechanochemical treatment

Directory of Open Access Journals (Sweden)

Turèániová ¼udmila

1998-09-01

Full Text Available The possibility of application of a new process GACL (Grinding and Aqueous Caustic Leaching for the reduction of mineral components in the brown coal Nováky was tested. The simultaneous grinding and chemical leaching enable us to extract 41 % total sulphur, 95 % arsenic and to reduce the ash content to 43 %. The process proceeds at the atmospheric pressure, temperature 90oC and in diluted NaOH solutions (5 %.

Processing of low grade uranium ores

International Nuclear Information System (INIS)

Michel, P.

1978-10-01

Four types of low-grade ores are studied: (1) Low-grade ores that must be extracted because they are enclosed in a normal-grade deposit. Heap leaching is the processing method which is largely used. (2) Normal-grade ores contained in low-amplitude deposits. They can be processed using in-place leaching as far as the operation does not need any large and expensive equipment. (3) Medium-grade ores in medium-amplitude deposits. A simplified conventional process can be applied using fast heap leaching. (4) Low-grade ores in large deposits. The report explains processing possibilities leading in most cases to the use of in-place leaching. The operating conditions of this method are laid out, especially the selection of the leaching agents and the preparation of the ore deposit

Slag Treatment Followed by Acid Leaching as a Route to Solar-Grade Silicon

NARCIS (Netherlands)

Meteleva-Fischer, Y.V.; Yang, Y.; Boom, R.; Kraaijveld, B.; Kuntzel, H.

2012-01-01

Refining of metallurgical-grade silicon was studied using a process sequence of slag treatment, controlled cooling, and acid leaching. A slag of the Na2O-CaO-SiO2 system was used. The microstructure of grain boundaries in the treated silicon showed enhanced segregation of impurities, and the

How did women count? A note on gender-specific age heaping differences in the sixteenth to nineteenth centuries.

Science.gov (United States)

Földvári, Peter; Van Leeuwen, Bas; Van Leeuwen-Li, Jieli

2012-01-01

The role of human capital in economic growth is now largely uncontested. One indicator of human capital frequently used for the pre-1900 period is age heaping, which has been increasingly used to measure gender-specific differences. In this note, we find that in some historical samples, married women heap significantly less than unmarried women. This is still true after correcting for possible selection effects. A possible explanation is that a percentage of women adapted their ages to that of their husbands, hence biasing the Whipple index. We find the same effect to a lesser extent for men. Since this bias differs over time and across countries, a consistent comparison of female age heaping should be made by focusing on unmarried women.

Leaching of Au, Ag, and Pd from waste printed circuit boards of mobile phone by iodide lixiviant after supercritical water pre-treatment.

Science.gov (United States)

Xiu, Fu-Rong; Qi, Yingying; Zhang, Fu-Shen

2015-07-01

Precious metals are the most attractive resources in waste printed circuit boards (PCBs) of mobile phones. In this work, an alternative process for recovering Au, Ag, and Pd from waste PCBs of mobile phones by supercritical water oxidation (SCWO) pre-treatment combined with iodine-iodide leaching process was developed. In the process, the waste PCBs of mobile phones were pre-treated in supercritical water, then a diluted hydrochloric acid leaching (HL) process was used to recovery the Cu, whose leaching efficiency was approximately 100%, finally the resulting residue was subjected to the iodine-iodide leaching process for recovering the Au, Ag, and Pd. Experimental results indicated that SCWO pre-treatment temperature, time, and pressure had significant influence on the Au, Ag, and Pd leaching from (SCWO+HL)-treated waste PCBs. The optimal SCWO pre-treatment conditions were 420°C and 60min for Au and Pd, and 410°C and 30min for Ag. The optimum dissolution parameters for Au, Pd, and Ag in (SCWO+HL)-treated PCBs with iodine-iodide system were leaching time of 120min (90min for Ag), iodine/iodide mole ratio of 1:5 (1:6 for Ag), solid-to-liquid ratio (S/L) of 1:10g/mL (1:8g/mL for Ag), and pH of 9, respectively. It is believed that the process developed in this study is environment friendly for the recovery of Au, Ag, and Pd from waste PCBs of mobile phones by SCWO pre-treatment combined with iodine-iodide leaching process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Generalized stress field in granular soils heap with Rayleigh–Ritz method

Directory of Open Access Journals (Sweden)

Gang Bi

2017-02-01

Full Text Available The stress field in granular soils heap (including piled coal will have a non-negligible impact on the settlement of the underlying soils. It is usually obtained by measurements and numerical simulations. Because the former method is not reliable as pressure cells instrumented on the interface between piled coal and the underlying soft soil do not work well, results from numerical methods alone are necessary to be doubly checked with one more method before they are extended to more complex cases. The generalized stress field in granular soils heap is analyzed with Rayleigh–Ritz method. The problem is divided into two cases: case A without horizontal constraint on the base and case B with horizontal constraint on the base. In both cases, the displacement functions u(x, y and v(x, y are assumed to be cubic polynomials with 12 undetermined parameters, which will satisfy the Cauchy's partial differential equations, generalized Hooke's law and boundary equations. A function is built with the Rayleigh–Ritz method according to the principle of minimum potential energy, and the problem is converted into solving two undetermined parameters through the variation of the function, while the other parameters are expressed in terms of these two parameters. By comparison of results from the Rayleigh–Ritz method and numerical simulations, it is demonstrated that the Rayleigh–Ritz method is feasible to study the generalized stress field in granular soils heap. Solutions from numerical methods are verified before being extended to more complicated cases.

Summary of the engineering assessment of inactive uranium mill tailings, Green River site, Green River, Utah

International Nuclear Information System (INIS)

1981-08-01

Radon gas released from the 123,000 tons of tailings at the Green River site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The five alternative actions range from millsite decontamination with the addition of 3 m of stabilization cover material, to removal of the tailings to remote disposal sites and decontamination of the tailings site. Cost estimates for the five options range from about $4,300,000 for stabilization in-place, to about $9,600,000 for disposal at a distance of about 30 miles. Three principal alternatives for the reprocessing of the Green River tailings were examined: heap leaching, treatment at an existing mill, and reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $1,800/lb by heap leach and $1,600/lb by conventional plant processes

Co-treatment of spent cathode carbon in caustic and acid leaching process under ultrasonic assisted for preparation of SiC.

Science.gov (United States)

Yuan, Jie; Xiao, Jin; Li, Fachuang; Wang, Bingjie; Yao, Zhen; Yu, Bailie; Zhang, Liuyun

2018-03-01

Spent cathode carbon (SCC) from aluminum electrolysis has been treated in ultrasonic-assisted caustic leaching and acid leaching process, and purified SCC used as carbon source to synthesize silicon carbide (SiC) was investigated. Chemical and mineralogical properties have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), and thermogravimetry and differential scanning calorimetry (TGA-DSC). Various experimental factors temperature, time, liquid-solid ratio, ultrasonic power, and initial concentration of alkali or acid affecting on SCC leaching result were studied. After co-treatment with ultrasonic-assisted caustic leaching and acid leaching, carbon content of leaching residue was 97.53%. SiC power was synthesized by carbothermal reduction at 1600 °C, as a result of yield of 76.43%, and specific surface area of 4378 cm 2 /g. This is the first report of using purified SCC and gangue to prepare SiC. The two industrial wastes have been used newly as secondary sources. Furthermore, ultrasonic showed significant effect in SCC leaching process. Copyright © 2017 Elsevier B.V. All rights reserved.

Coal Mining Spoil Heap Management as urban solid waste dump; Utilizacion de Escombreras de Carbon como Vertedero Controlado de Residuos Solidos Urbanos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the coordinated project DISPOSAL OF SOLID RESIDUES FROM COAL it is included the project Coal Mining Spoil Heap Management as Urban Solid Waste Dump. The main target of this project consisted of determining the viability of using coal mining spoil heaps, as controlled dubbish dump of urban solid wastes. The working plan to achieve this objective was composed of the following stages: 1. Urban solid wastes characterization. 2. Methodology to be followed for the selection of coal mining spoil heaps as controlled dump of urban solid wastes. 2.1 Classification and preliminary assessment of the possibility of using spoil heaps as urban solid waste dumps (APT/NON APT). 2.2 Realization of geological, geotechnical, hydrogeological and environmental studies applied to the spoil heaps classified as APT. 2.3 Analysis of the compatibility of the mining activity with the urban solid wastes dumped on the spoil heap. 2.4 Analysis of the use of coal mining wastes in the rubbish dump operative life. 3. Extraction of conclusions. The works were focused in the Leon province. As result of the researches we obtained the following results and conclusions: In the areas studied, only two emplacements are optima to dump urban solid wastes; spoil heap n. 13. Roguera Mine (Cinera-Matallana) and the open pit mine n. 4, Las Chaviadas, in Villablino. The active spoil heap use as controlled rubbish dump can cause, if not managed adequately, several coperating and occupational problems to the mine and to the company that manages the urban solid wastes. The abandoned spoil heap utilisation is difficult due to the problems that would arise when conditioning the site to be use as rubbish dump. The use of abandoned open pit mines, as controlled rubbish dump is feasible if geological, geotechnical, hydrogeological and environmental studies support it. It's possible the use of the coal mining wastes in the different operatives phases of the controlled rubbish dump. The evaluation methodology

Coal Mining Spoil Heap Management as urban solid waste dump; Utilizacion de Escombreras de Carbon como Vertedero Controlado de Residuos Solidos Urbanos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the coordinated project DISPOSAL OF SOLID RESIDUES FROM COAL it is included the project Coal Mining Spoil Heap Management as Urban Solid Waste Dump. The main target of this project consisted of determining the viability of using coal mining spoil heaps, as controlled dubbish dump of urban solid wastes. The working plan to achieve this objective was composed of the following stages: 1. Urban solid wastes characterization. 2. Methodology to be followed for the selection of coal mining spoil heaps as controlled dump of urban solid wastes. 2.1 Classification and preliminary assessment of the possibility of using spoil heaps as urban solid waste dumps (APT/NON APT). 2.2 Realization of geological, geotechnical, hydrogeological and environmental studies applied to the spoil heaps classified as APT. 2.3 Analysis of the compatibility of the mining activity with the urban solid wastes dumped on the spoil heap. 2.4 Analysis of the use of coal mining wastes in the rubbish dump operative life. 3. Extraction of conclusions. The works were focused in the Leon province. As result of the researches we obtained the following results and conclusions: In the areas studied, only two emplacements are optima to dump urban solid wastes; spoil heap n. 13. Roguera Mine (Cinera-Matallana) and the open pit mine n. 4, Las Chaviadas, in Villablino. The active spoil heap use as controlled rubbish dump can cause, if not managed adequately, several coperating and occupational problems to the mine and to the company that manages the urban solid wastes. The abandoned spoil heap utilisation is difficult due to the problems that would arise when conditioning the site to be use as rubbish dump. The use of abandoned open pit mines, as controlled rubbish dump is feasible if geological, geotechnical, hydrogeological and environmental studies support it. It's possible the use of the coal mining wastes in the different operatives phases of the controlled rubbish dump. The evaluation methodology developed

Quality assurance of MSWI bottom ash. Environmental properties; Kvalitetssaekring av slaggrus. Miljoemaessiga egenskaper

Energy Technology Data Exchange (ETDEWEB)

Flyhammar, Peter [Lund Univ. (Sweden). Dept. of Engineering Geology

2006-04-15

In Sweden several hundred tonnes of MSWI bottom ash are generated annually at 29 incineration plants for municipal solid waste. So far bottom ash has mainly been disposed in to landfills or used as cover material in landfills or in other construction works at landfills. A few applications of bottom ash in construction works outside landfills have been reported. A large problem for the market of bottom ash and other secondary materials outside Swedish waste treatment plants is the lack of roles and regulations for a non-polluting use. During 2002 Hartlen and Groenholm (HG) presented a proposal to a system to assure the quality of bottom ash after homogenization and stabilization. A quality assurance of environmental properties should be based on leaching tests. The aim of this project was to study how the control of environmental properties of bottom ash earlier described in e.g. a product information sheet should be worked out. The starting-point has been a control system for bottom ash developed by the Sysav company. Different leaching tests illustrate however different aspects of the environmental properties, e.g. short-term and long-term leaching. Limit and target values for different variables could affect both the possibilities to use bottom ash as well as the sampling from storage heaps. We have chosen to investigate: pH, availability and leached amount and the connection between these variables; the possibilities to use pH or the availability to assess both short-term and long term leaching properties; how the number of subsamples that should be collected from a storage heap is affected by different control variables and quality requirements; how bottom ash is stabilized by today's storage technology and how the technology could be improved. Our sample test of bottom ash from Swedish incineration plants indicates that the availability of elements such as Cd, Cu, Cr, Ni, Pb and Zn in bottom ash usually is below Sysav's target values. Extreme values

Acid pre-treatment method for in situ ore leaching

International Nuclear Information System (INIS)

Mallon, R.G.; Braun, R.L.

1975-01-01

An acid leaching method is described for the recovery of a desired element from a subterranean rubblized body of primary ore containing the element and also having associated therewith a carbonate mineral wherein the rubblized ore body is flooded with an aqueous acidic solution in order to release carbon dioxide from the associated carbonate mineral. After a substantial portion of the available carbon dioxide is released and removed from the ore body, as by venting to the atmosphere, an oxidizing gas is introduced into the flooded, rubblized ore to oxidize the ore and form an acid leach solution effective in the presence of the dissolved oxidizing gas to dissolve the ore and cause the desired element to go into solution. The leach solution is then circulated to the surface where the metal values are recovered therefrom

The rehabilitation of Rum Jungle

International Nuclear Information System (INIS)

Anon.

1986-01-01

The mining and treatment operation and disposal of waste products from the mining and treatment was carried out within the structures of the environmental regulations applying between 1954 and 1971. As a result, the operation left a legacy of continuing environmental pollution which the Rum Jungle Rehabilitation Project was aimed at alleviating. The problems at Rum Jungle consisted of three major elements: overburden heaps and copper heap leach pile were slowly oxidising producing acid mine drainage, the most serious form of pollution at Rum Jungle; water in the open cut pits became acidic and contained significant concentrations of heavy metals; the tailings dam was a low level source of radioactivity, aesthetically disastrous and a source of acids and heavy metals

Thermal treatment and ammoniacal leaching for the recovery of valuable metals from spent lithium-ion batteries.

Science.gov (United States)

Chen, Yongming; Liu, Nannan; Hu, Fang; Ye, Longgang; Xi, Yan; Yang, Shenghai

2018-05-01

The recycling of spent commercial lithium-ion batteries (LIBs) generates numerous environmental and economic benefits. In this research, a thermal treatment-ammoniacal leaching process is proposed to recover valuable metals from cathode active powder. Based on the thermal behavior by TG-DSC analysis, the cathode active powder is calcined at 300 °C and 550 °C in air atmosphere, and the crystalline phase characterization indicates that a new phase of Co 3 O 4 appears in the cathode active powder calcined at 550 °C, which signifies that the layer structure of LiCoO 2 collapses. The valence of manganese increases to form Li 4 Mn 5 O 12 in spinel structure of LiMn 2 O 4 . Using calcined cathode powder as feed material, ammoniacal leaching is carried out in (NH 4 ) 2 SO 4 -(NH 4 ) 2 SO 3 solution. Under the optimum conditions, Ni, Co, Mn and Li can be completely leached out with efficiencies of 98%, 81%, 92% and 98%, respectively. However, with the increase of ammonia concentration, the leaching efficiency of Mn decreases dramatically to 4% due to the formation of double salts. It is found that Co and Mn can be precipitated into residues in the form of (NH 4 ) 2 Co(SO 4 ) 2 ·H 2 O, (NH 4 ) 2 Mn(SO 3 ) 2 ·H 2 O and (NH 4 ) 2 Mn(SO 4 ) 2 ·6H 2 O under different leaching parameters. Based on the corresponding relationship between the leaching efficiency and phase evolution of object element, selective leaching can be achieved by controlling the formation of double salts. Copyright © 2018 Elsevier Ltd. All rights reserved.

Heavy metals in soil on spoil heap of an abandoned lead ore ...

African Journals Online (AJOL)

EJIRO

(Ti, Fe and Al) of a soil profile on spoil heap were examined. 54 soil samples were .... move gravel and rocks, put in plastic bags then sent to the Service. Central du ..... micro- organisms and microbial processes in agricultural soils. A review.

The accumulation of elements in plants growing spontaneously on small heaps left by the historical Zn-Pb ore mining.

Science.gov (United States)

Stefanowicz, Anna M; Stanek, Małgorzata; Woch, Marcin W; Kapusta, Paweł

2016-04-01

The study evaluated the levels of nine metals, namely Ca, Cd, Fe, K, Mg, Mn, Pb, Tl, and Zn, in soils and tissues of ten plant species growing spontaneously on heaps left by historical mining for Zn-Pb ores. The concentrations of Cd, Pb, Tl, and Zn in heap soils were much higher than in control soils. Plants growing on heaps accumulated excessive amounts of these elements in tissues, on average 1.3-52 mg Cd kg(-1), 9.4-254 mg Pb kg(-1), 0.06-23 mg Tl kg(-1) and 134-1479 mg Zn kg(-1) in comparison to 0.5-1.1 mg Cd kg(-1), 2.1-11 mg Pb kg(-1), 0.02-0.06 mg Tl kg(-1), and 23-124 mg Zn kg(-1) in control plants. The highest concentrations of Cd, Pb, and Zn were found in the roots of Euphorbia cyparissias, Fragaria vesca, and Potentilla arenaria, and Tl in Plantago lanceolata. Many species growing on heaps were enriched in K and Mg, and depleted in Ca, Fe, and Mn. The concentrations of all elements in plant tissues were dependent on species, organ (root vs. shoot), and species-organ interactions. Average concentrations of Ca, K, and Mg were generally higher in shoots than in roots or similar in the two organs, whereas Cd, Fe, Pb, Tl, and Zn were accumulated predominantly in the roots. Our results imply that heaps left by historical mining for Zn-Pb ores may pose a potential threat to the environment and human health.

Heavy Metal Leaching as Affected by Long-Time Organic Waste Fertilizer Application.

Science.gov (United States)

Lekfeldt, Jonas Duus Stevens; Holm, Peter E; Kjærgaard, Charlotte; Magid, Jakob

2017-07-01

The recycling of urban waste products as fertilizers in agriculture may introduce contaminants such as heavy metals into soil that may leach and contaminate groundwater. In the present study, we investigated the leaching of heavy metals from intact soil cores collected in the long-term agricultural field trial CRUCIAL. At the time of sampling, the equivalent of >100 yr of urban waste fertilizers following Danish legislation had been applied. The leaching of Cu was significantly increased in the treatments receiving organic waste products compared with the unfertilized control but remained below the permissible level following Danish drinking water guidelines. The leaching of Cu was controlled primarily by the topsoil Cu content and by the leaching of dissolved organic carbon (DOC) but at the same time significantly correlated with leaching of colloids in soils that had not received fertilizer or had received an organic fertilizer with a low concentration of Cu. The leaching of Zn, Cd, and Co was not significantly increased in urban waste-fertilized treatments. The leaching of Mo was elevated in accelerated waste treatments (both agricultural and urban), and the leaching of Mo was linked to the leaching of DOC. Since leaching of Cr and Pb was strongly linked to the level of colloid leaching, leaching of these metals was reduced in the urban waste treatments. Overall, the results presented should not raise concern regarding the agricultural use of urban waste products in agriculture as long as the relevant guidelines are followed. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Characterization of uranium- and plutonium-contaminated soils by electron microscopy

International Nuclear Information System (INIS)

Buck, E.C.; Dietz, N.L.; Fortner, J.A.; Bates, J.K.; Brown, N.R.

1995-01-01

Electron beam techniques have been used to characterize uranium-contaminated soils from the Fernald Site in Ohio, and also plutonium-bearing 'hot particles, from Johnston Island in the Pacific Ocean. By examining Fernald samples that had undergone chemical leaching it was possible to observe the effect the treatment had on specific uranium-bearing phases. The technique of Heap leaching, using carbonate solution, was found to be the most successful in removing uranium from Fernald soils, the Heap process allows aeration, which facilitates the oxidation of uraninite. However, another refractory uranium(IV) phase, uranium metaphosphate, was not removed or affected by any soil-washing process. Examination of ''hot particles'' from Johnston Island revealed that plutonium and uranium were present in 50--200 nm particles, both amorphous and crystalline, within a partially amorphous aluminum oxide matrix. The aluminum oxide is believed to have undergone a crystalline-to-amorphous transition caused by alpha-particle bombardment during the decay of the plutonium

Quality assurance of MSWI bottom ash. Environmental properties; Kvalitetssaekring av slaggrus. Miljoemaessiga egenskaper

Energy Technology Data Exchange (ETDEWEB)

Flyhammar, Peter [Lund Univ. (Sweden). Engineering Geology

2006-04-15

In Sweden, several hundred tonnes of MSWI bottom ash are generated annually at 29 incineration plants for municipal solid waste. So far bottom ash has mainly been disposed in to landfills or used as cover material in landfills or in other construction works at landfills. A few applications of bottom ash in construction works outside landfills have been reported. A large problem for the market of bottom ash and other secondary materials outside Swedish waste treatment plants is the lack of roles and regulations for a non-polluting use. During 2002 Hartlen and Groenholm presented a proposal to a system to assure the quality of bottom ash after homogenization and stabilization. They notice that the leaching of salts and metals to ground water constitutes the largest risk for the environment during use of bottom ash. Therefore, a quality assurance of environmental properties should be based on leaching tests. The aim of this project was to study how the control of environmental properties of bottom ash (at first hand leaching properties) earlier described in e.g. a product information sheet should be worked out. The starting-point has been a control system for bottom ash developed by Sysav. Different leaching tests illustrate however different aspects of the environmental properties, e.g. short-term and long-term leaching. Limit and target values for different variables could affect both the possibilities to use bottom ash as well as the sampling from storage heaps. We have chosen to investigate pH, availability and leached amount and the connection between these variables. the possibilities to use pH or the availability to assess both short-term and longterm leaching properties. how the number of subsamples that should be collected from a storage heap is affected by different control variables and quality requirements. how bottom ash is stabilized by today's storage technology and how the technology could be improved. Our sample test of bottom ash from Swedish

Processing of low-grade uranium ores

International Nuclear Information System (INIS)

Michel, P.

1975-01-01

Four types of low grade ores are studied. Low grade ores which must be extracted because they are enclosed in a normal grade deposit. Heap leaching is the processing method which is largely used. It allows to obtain solutions or preconcentrates which may be delivered at the nearest plant. Normal grade ores contained in a low amplitude deposit which can be processed using leaching as far as the operation does not need any large expensive equipment. Medium grade ores in medium amplitude deposits to which a simplified conventional process can be applied using fast heap leaching. Low grade ores in large deposits. The processing possibilities leading to use in place leaching are explained. The operating conditions of the method are studied (leaching agent, preparation of the ore deposit to obtain a good tightness with regard to the hydrological system and to have a good contact between ore and reagent) [fr

Metallurgical treatment of Waelz oxides by alkaline leaching using ammonium carbonate; Tratamiento metalurgico de los oxidos Waelz mediante lixiviacion alcalina utilizando carbonato amonico

Energy Technology Data Exchange (ETDEWEB)

Meseguer, V.; Lozano, L.J.; Juan, D. de [Dpto. Ingenieria Quimica Cartagena. Universidad de Murcia, Murcia (Spain)

1997-09-01

A method to carry out the treatment of the Waelz oxides is proposed, and the principal stages implicated are studied laboratory-scale. The process consists of the oxides leaching with an ammonium carbonate/ammonia solution, followed the recovery of the zinc leached by means of its precipitation as zinc basic carbonate. The process stages that have been studied are: Waelz oxides leaching, loaded leach purification, zinc precipitation, zinc basic carbonate washing and zinc basic carbonate transformation. The designed treatment presents a null environmental impact, and more than 90% of the zinc contained in the Waelz oxides, as well as 80% of the copper and cadmium contents could be recovered. Also, the process presents great flexibility as soon as zinc could be recovered in the most convenient form (zinc metal, oxide or salt). (Author) 14 refs.

Investigation of the leaching behavior of lead in stabilized/solidified waste using a two-year semi-dynamic leaching test.

Science.gov (United States)

Xue, Qiang; Wang, Ping; Li, Jiang-Shan; Zhang, Ting-Ting; Wang, Shan-Yong

2017-01-01

Long-term leaching behavior of contaminant from stabilization/solidification (S/S) treated waste stays unclear. For the purpose of studying long-term leaching behavior and leaching mechanism of lead from cement stabilized soil under different pH environment, semi-dynamic leaching test was extended to two years to investigate leaching behaviors of S/S treated lead contaminated soil. Effectiveness of S/S treatment in different scenarios was evaluated by leachability index (LX) and effective diffusion coefficient (D e ). In addition, the long-term leaching mechanism was investigated at different leaching periods. Results showed that no significant difference was observed among the values of the cumulative release of Pb, D e and LX in weakly alkaline and weakly acidic environment (pH value varied from 5.00 to 10.00), and all the controlling leaching mechanisms of the samples immersed in weakly alkaline and weakly acidic environments turned out to be diffusion. Strong acid environment would significantly affect the leaching behavior and leaching mechanism of lead from S/S monolith. The two-year variation of D e appeared to be time dependent, and D e values increased after the 210 th day in weakly alkaline and weakly acidic environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Earthworm succession in afforested colliery spoil heaps in the Sokolov region, Czech Republic

Czech Academy of Sciences Publication Activity Database

Pižl, Václav

2001-01-01

Roč. 9, č. 4 (2001), s. 359-364 ISSN 1061-2971 Institutional research plan: CEZ:AV0Z6066911 Keywords : earthworms * colliery spoil heaps * succession Subject RIV: EH - Ecology, Behaviour Impact factor: 1.011, year: 2001

Method of continuous pressure leaching of ores

International Nuclear Information System (INIS)

Fiala, P.; Baloun, S.; Polansky, M.

1987-01-01

Ore leaching, especially suspensions of ground ore or fine ore fractions from physical treatment was divided into two operations. The former, i.e., ore mixing with technical grade concentrated sulfuric acid proceeded in a separate mixer. The mixture was then transported into an autoclave where the actual leaching proceeded for 2 to 4 hours. The extracted mixture was discharged through the autoclave bottom. The leaching autoclave used can be without any inner structures. The separation of mixing from the actual leaching allows processing ores with high levels of clay components, increasing operating reliability of the facility, reducing consumption of special structural materials and energy, and increasing process efficiency. (E.S.)

Treatment of solid waste highly contaminated by alpha emitters: Low-temperature impact crushing, leaching and incineration

International Nuclear Information System (INIS)

Bertolotti, G.; Vigreux, B.; Caillol, A.; Koehly, G.

1987-01-01

Reprocessing plants, hot laboratories and fuel fabrication plants produce solid wastes containing residual amounts of plutonium and uranium in nitrate and oxide form at concentrations up to several tens of grams per m/sup 3/. Dismantling of nuclear facilities having handled these radioelements also generates large volumes of solid wastes highly contaminated with alpha emitters. It is desirable to process these alpha wastes to recover valuable fissile materials and/or permit surface storage. Solid waste treatment by low-temperature impact crushing and then leaching, after minimal sorting and classifying at the sites of production, meets the corresponding requirements for high volume reduction plus fissile material recovery or waste decontamination. Additional volume reduction of crushed wastes containing mainly combustible materials can be obtained by incineration. This is facilitated by the low fissile material content after low-temperature impact crushing and leaching. Sorted wastes can also be leached or incinerated directly after, in most cases, crushing by more conventional techniques

Nomograms to calculate stability in slate and granite spoil heaps; Abacos para el calculo de estabilidad en escombreras de pizarra y granito

Energy Technology Data Exchange (ETDEWEB)

Paz Freire, M.; Taboada Castro, J.; Rivas Brea, T.; Giraldez Perez, E.; Araujo Fernandez, M.

2011-07-01

One of the main problems involved in the mining of slate and ornamental granite is the unavoidable generation of waste rock, which must be stored in spoil heaps under suitably integrated, secure and stable conditions. Our work here focuses on this last point. To study the risk of instability within spoil heaps we have analysed the performance of a wide number of models with regard to circular slope failure, taking into account the different degrees of compactness of the material, the characteristics of the material itself, the effect of water pressure and the geometry of the heap. From this analysis we obtained more than 300 safety criteria, which were then used to draw up a series of nomograms to allow us to determine the risk of sliding in any granite or slate spoil heap. Thus, nomograms prove themselves to be suitable, quick, easy-to-use tools for preliminary studies of new structures, for periodic analyses of existing structures and to investigate structures that are due to be modified. (Author) 24 refs.

Leading practice water monitoring in northern Australia

International Nuclear Information System (INIS)

Bush, M.; Turner, K.

2010-01-01

Ranger Uranium Mine is undergoing an environmental impact statement assessment process to develop a Heap Leach facility to treat low grade ore on site. The facility is proposed to be located in the relatively unimpacted Gulungul catchment within the Ranger Project Area which itself is surrounded by, but excluded from, the World Heritage listed Kakadu National Park. The Supervising Scientist Division (SSD) acts to ensure the downstream environment is protected from mine-related impacts. To achieve this SSD will develop a leading practice monitoring program for Gulungul Creek to monitor potential impacts to this catchment from the Heap Leach facility. (author)

HEPA filter leaching concept validation trials at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Chakravartty, A.C.

1995-04-01

The enclosed report documents six New Waste Calcining Facility (NWCF) HEPA filter leaching trials conducted at the Idaho Chemical Processing Plant using a filter leaching system to validate the filter leaching treatment concept. The test results show that a modified filter leaching system will be able to successfully remove both hazardous and radiological constituents to RCRA disposal levels. Based on the success of the filter leach trials, the existing leaching system will be modified to provide a safe, simple, effective, and operationally flexible filter leaching system

Predictive geochemical modeling of uranium and other contaminants in laboratory columns in relatively oxidizing, carbonate-rich solutions

International Nuclear Information System (INIS)

Longmire, P.; Turney, W.R.; Mason, C.F.V.

1994-01-01

Carbonate heap leaching of uranium-contaminated soils and sediments represents a viable, cost-effective remediation technology. Column experiments have been conducted using 0.1, 0.25, and 0.5 M Na 2 CO 3 /NaHCO 3 solutions for leaching uranium from soils located adjacent to an incinerator at the Fernald Environmental Management Project (FEMP) site. Results from column experiments and geochemical modeling are used to quantitatively evaluate the effectiveness of heap leaching. Leach efficiencies of up to 72 wt.% of total uranium in CaO-agglomerated soil result from dissolution of uranium (U(VI)-dominated) minerals, formation of the soluble complex UO 2 (CO 3 ) 3 4- , and uranium desorption from clay minerals, ferric hydroxides, and humic acids. Parameters that control the extent of uranium extraction include pH, Eh, temperature, carbonate concentration, lixiviant-flow rate, pore-solution chemistry, solid phases, and soil texture

Microbiology of Composting Pig Waste: Comparison of Vermicomposting and Open Heap Techniques

Directory of Open Access Journals (Sweden)

Ogefere, H. O.

2010-01-01

Full Text Available Against the background of an effective waste management, microbiological studies of composting pig waste were investigated. Freshly deposited excreta from confined pigs in a private pig farm in Benin City, Edo State, Nigeria were composted by two aerobic methods – vermicomposting and open heap. Microbial (bacterial and fungal counts and characterization were carried out periodically within the 40 weeks of composting, using standard techniques. The results showed that only duration of composting significantly (p<.0.05 affected microbial counts as the counts decreased from the initial value at week zero to much lower value at week 40. A total of 274 bacterial and fungal isolates were recovered from the composting waste and majority (60.58% were isolated from the open heap. Bacillus subtilis, Pseudomonas aeruginosa and Aspergillus flavus were the predominant isolates recovered (9.49% each, and were the only isolates recovered throughout the period of composting irrespective of the composting technique. Staphylococcus aureus and Salmonella typhimurium were the least isolated (1.09% each. Vermicomposting technique was recommended on health and environmental grounds.

Leaching of arsenic, copper and chromium from thermally treated soil.

Science.gov (United States)

Kumpiene, Jurate; Nordmark, Désirée; Hamberg, Roger; Carabante, Ivan; Simanavičienė, Rūta; Aksamitauskas, Vladislovas Česlovas

2016-12-01

Thermal treatment, if properly performed, is an effective way of destroying organic compounds in contaminated soil, while impact on co-present inorganic contaminants varies depending on the element. Leaching of trace elements in thermally treated soil can be altered by co-combusting different types of materials. This study aimed at assessing changes in mobility of As, Cr and Cu in thermally treated soil as affected by addition of industrial by-products prior to soil combustion. Contaminated soil was mixed with either waste of gypsum boards, a steel processing residue (Fe 3 O 4 ), fly ash from wood and coal combustion or a steel abrasive (96.5% Fe 0 ). The mixes and unamended soil were thermally treated at 800 °C and divided into a fine fraction 0.125 mm to simulate particle separation occurring in thermal treatment plants. The impact of the treatment on element behaviour was assessed by a batch leaching test, X-ray absorption spectroscopy and dispersive X-ray spectrometry. The results suggest that thermal treatment is highly unfavourable for As contaminated soils as it increased both the As leaching in the fine particle size fraction and the mass of the fines (up to 92%). Soil amendment with Fe-containing compounds prior to the thermal treatment reduced As leaching to the levels acceptable for hazardous waste landfills, but only in the coarse fraction, which does not justify the usefulness of such treatment. Among the amendments used, gypsum most effectively reduced leaching of Cr and Cu in thermally treated soil and could be recommended for soils that do not contain As. Fly ash was the least effective amendment as it increased leaching of both Cr and As in majority of samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

Treatment of Petroleum Sludge By Using Solidification/Stabilization (S/S) Method : Effect of Hydration Days to Heavy Metals Leaching and Strength

Science.gov (United States)

Murshid, N.; Kamil, N. A. F. M.; Kadir, A. A.

2018-04-01

Petroleum sludge is one of the major solid wastes generated in the petroleum industry. Generally, there are numbers of heavy metals in petroleum sludge and one treatment that is gaining prominence to treat a variety of mixed organic and inorganic waste is solidification/stabilization (S/S) method. The treatment protects human health and the environment by immobilizing contaminants within the treated material and prevents migration of the contaminants. In this study, solidification/stabilization (S/S) method has been used to treat the petroleum sludge. The comparison of hydration days, namely, 7th and 28th days in these cement-based waste materials were studied by using Synthetic Precipitate Leaching Procedure (SPLP). The results were compared to the United States Environmental Protection Agency (USEPA) standards. The results for leaching test concluded that less percentage OPC gave maximum concentration of heavy metals leaching due to deficient in Calcium Oxide (CaO), which is can caused weak solidification in the mixture. Physical and mechanical properties conducted such as compressive strength and density test. From the results, it shows addition up to of 30percentage PS give results which comply with minimum landfill dispose limit. The results shows correlation between strength and density are strong regression coefficient of 82.7%. In conclusion, S/S method can be alternative disposal method for PS in the same time complies with standard for minimum landfill disposal limit. The results for leaching test concluded the less OPC percentage gave maximum concentration of heavy metals leaching.

The performance with data processing of chemical treatment with leaching and bio-leaching

OpenAIRE

Agron, Alili; Krstev, Boris; Krstev, Aleksandar; Stamenov, Goran

2015-01-01

The refractory or low grade lead/zinc domestic ores in Republic of Macedonia are investigated by conventional separation technology or flotation separation. In the meantime, investigations are directed to the new possibilities of leaching by microorganisms – bioleaching. The paper is result of these technologies and investigations carried out for recovery of in the mentioned ores. Using Simplex EVOP and computer program Multisimplex performances are appropriate and most acceptable and excel...

Using H2O2 as oxidant in leaching of uranium ores. The new research on the reaction of H2O2 with Fe2+

International Nuclear Information System (INIS)

Gao Xizhen

1997-05-01

The new research on the reaction of H 2 O 2 with Fe 2+ has been studied. Through determining the electric potential, pH and O 2 release during the mutual titration between H 2 O 2 solution and FeSO 4 solution, deduced the chemical equations of H 2 O 2 (without free hydroxyl) oxidizing FeSO 4 and Fe 2 (SO 4 ) 3 oxidizing H 2 O 2 . The research results show that acid is a catalytic agent for decomposing H 2 O 2 to be O 2 and H 2 O besides iron ions. The maximum oxidizing potential is up to about 640 mV. While using H 2 O 2 as an oxidant in uranium heap leaching and in-situ leaching, controlling electric potential can be regarded as a method for adjusting the feeding speed of H 2 O 2 to keep the electric potential below 500 mV, thus the H 2 O 2 decomposition can be reduced. (13 refs., 3 tabs., 1 fig.)

Phytotoxicity and groundwater impacts of leaching from thermal treatment residues in roadways.

Science.gov (United States)

Phoungthong, Khamphe; Shao, Li-Ming; He, Pin-Jing; Zhang, Hua

2018-01-01

The use of coal fly ash (CFA), municipal solid waste incinerator bottom ash (MSWIBA) and flue gas desulfurization residue (FGDR) in road construction has become very common owing to its economical advantages. However, these residues may contain toxic constituents that pose an environmental risk if they leach out and flow through the soil, surface water and groundwater. Therefore, it is necessary to assess the ecotoxicity and groundwater impact of these residues before decisions can be made regarding their utilization for road construction. In this study, the physico-chemical characteristics, leaching and phytotoxicity of these residues were investigated. Specifically, multivariate analyses were used to evaluate the contributions of the leaching constituents of the CFA, MSWIBA and FGDR leachates to the germination index of wheat seeds. B, Ba, Cr, Cu, Fe and Pb were found to be more toxic to the wheat seeds than the other heavy metals. Furthermore, the leached concentrations of the constituents from the CFA, MSWIBA and FGDR were below the regulatory threshold limits of the Chinese identification standard for hazardous wastes. Analyses conducted using a numerical groundwater model (WiscLEACH) indicated that the predicted field concentrations of metals from the CFA, MSWIBA and FGDR increased with time up to about 30years at the point of compliance, then decreased with time and distance. Overall, this study demonstrated that the risks resulting from MSWIBA, CFA and FGDR leaching could be assessed before its utilization for road construction, providing crucial information for the adoption of these alternative materials. Copyright © 2016. Published by Elsevier B.V.

Recent developments in uranium resources and production with emphasis on in situ leach mining. Proceedings of a technical meeting

International Nuclear Information System (INIS)

2004-06-01

presented, but also heap leaching, reflecting the importance of low cost production methods during these periods of low uranium price. Papers are analysed and indexed individually

LEACH-A: An Adaptive Method for Improving LEACH Protocol

Directory of Open Access Journals (Sweden)

Jianli ZHAO

2014-01-01

Full Text Available Energy has become one of the most important constraints on wireless sensor networks. Hence, many researchers in this field focus on how to design a routing protocol to prolong the lifetime of the network. The classical hierarchical protocols such as LEACH and LEACH-C have better performance in saving the energy consumption. However, the choosing strategy only based on the largest residue energy or shortest distance will still consume more energy. In this paper an adaptive routing protocol named “LEACH-A” which has an energy threshold E0 is proposed. If there are cluster nodes whose residual energy are greater than E0, the node of largest residual energy is selected to communicated with the base station; When all the cluster nodes energy are less than E0, the node nearest to the base station is select to communication with the base station. Simulations show that our improved protocol LEACH-A performs better than the LEACH and the LEACH-C.

Uranium ((234)U, (235)U and (238)U) contamination of the environment surrounding phosphogypsum waste heap in Wiślinka (northern Poland).

Science.gov (United States)

Olszewski, Grzegorz; Boryło, Alicja; Skwarzec, Bogdan

2015-08-01

The aim of this work was to determine the uranium concentration ((234)U, (235)U and (238)U) and values of the activity ratio (234)U/(238)U in soil samples collected near phosphogypsum waste heap in Wiślinka (northern Poland). On the basis of the studies it was found that the values of the (234)U/(238)U activity ratio in the analyzed soils collected in the vicinity of phosphogypsum dump in Wiślinka are in most cases close to one and indicate the phosphogypsum origin of the analyzed nuclides. The obtained results of uranium concentrations are however much lower than in previous years before closing of the phosphogypsum stockpile. After this process and covering the phosphogypsum stockpile in Wiślinka with sewage sludge, phosphogypsum particles are successfully immobilized. In the light of the results the use of phosphate fertilizers seems to be a major problem. Prolonged and heavy rains can cause leaching accumulated uranium isotopes in the phosphogypsum stockpile, which will be washed into the Martwa Wisła and on the fields in the immediate vicinity of this storage. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study of radionuclide leaching from the residues of K Basin sludge dissolution

International Nuclear Information System (INIS)

Bechtold, D.B.

1998-01-01

The sludges remaining in the K Basins after removal of the spent N Reactor nuclear fuel will be conditioned for disposal. After conditioning, an acid-insoluble residue will remain that may require further leaching to properly condition it for disposal. This document presents a literature study to identify and recommend one or more chemical leaching treatments for laboratory testing, based on the likely compositions of the residues. The processes identified are a nitric acid cerate leach, a silver-catalyzed persulfate leach, a nitric hydrofluoric acid leach, an oxalic citric acid reactor decontamination leach, a nitric hydrochloric acid leach, a ammonium fluoride nitrate leach, and a HEOPA formate dehydesulfoxylate leach. All processes except the last two are recommended for testing in that order

Some factors affecting agitation leach test during in-situ leaching of uranium

International Nuclear Information System (INIS)

Liao Wensheng; Jiang Yan; Wang Limin; Shi Zhenfeng; Zhao Qiaofu; MARMAR

2014-01-01

The agitation leaching test is one of the most fundamental research works in in-situ leaching of uranium. Some factors affecting the test results were analyzed including stirring, leaching time, oxidizer used in alkaline leach, washing solution, the amount and size of ore samples. The results indicate that stirring can enhance diffusion velocity. The leach time l or 2 days is suitable for the samples containing accessible uranium and low acid consumption minerals; whereas 3 or 4 days for those containing refractory ore to leach and slowly acid consuming minerals. For the oxidizer used in alkaline leach, potassium permanganate is better than hydrogen peroxide. Recovery calculated by the leach solution can be directly obtained by its uranium level and the original volume of lixiviant without analyzing and calculating the washing solution. The appropriate amount and size of ore samples for the agitation leaching test are 60 g and <1 mm. By controlling the above factors, the agitation leach test can improve the applicability of the different ore samples and give the more reliable data. (authors)

Stabilization of heavy metals in fired clay brick incorporated with wastewater treatment plant sludge: Leaching analysis

Science.gov (United States)

Kadir, A. A.; Hassan, M. I. H.; Salim, N. S. A.; Sarani, N. A.; Ahmad, S.; Rahmat, N. A. I.

2018-04-01

Wastewater treatment sludge or known as sewage sludge is regarded as the residue and produced by the sedimentation of the suspended solid during treatment at the wastewater treatment plant. As such, this sludge was gained from the separation process of the liquids and solids. This sludge wastes has becomes national issues in recent years due to the increasing amount caused by population and industrialization growth in Malaysia. This research was conducted to fully utilize the sludge that rich in dangerous heavy metals and at the same time act as low cost alternative materials in brick manufacturing. The investigation includes determination of heavy metal concentration and chemical composition of the sludge, physical and mechanical properties. Wastewater treatment sludge samples were collected from wastewater treatment plant located in Johor, Malaysia. X-Ray Fluorescence was conducted to determine the heavy metals concentration of wastewater treatment sludge. Different percentage of sludges which are 0%, 1%, 5%, 10%, and 20%, has been incorporated into fired clay brick. The leachability of heavy metals in fired clay brick that incorporated with sludge were determined by using Toxicity Characteristic Leaching Procedure (TCLP) and Synthetic Precipitation Leachability Procedure (SPLP) that has been analyzed by using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The results show a possibility to stabilize the heavy metals in fired clay brick incorporated with wastewater treatment sludge. 20% of the sludge incorporated into the brick is the most suitable for building materials as it leached less heavy metals concentration and complying with USEPA standard.

Estimating Leaching Requirements for Barley Growth under Saline Irrigation

Directory of Open Access Journals (Sweden)

Ahmed Al-Busaidi

2012-01-01

Full Text Available The utilization of marginal water resources for agriculture is receiving considerable attention. The lands irrigated with saline water are required to reduce salt accumulations through leaching and/or drainage practices. A field experiment was carried out to investigate the effect of saline irrigation and leaching fraction on barley (Hordeum vulgare L. growth. For this purpose highly saline water was diluted to the salinity levels of 3, 6 and 9 dS m-1 and applied by drip irrigation at 0.0, 0.15, 0.20 and 0.25 leaching fractions (LF. The results of the experiment showed that both quantity and quality of water regulated salts distribution within the soil in the following manner: a the salts were found higher near or immediate below the soil surface; b an enhanced LF carried more salts down the soil horizon but there was no significant difference in plant yield between different treatments of leaching fractions. Salinity of water significantly impaired barley growth. The good drainage of sandy soil enhanced the leaching process and minimized the differences between leaching fractions. The increment in saline treatments (3, 6 and 9 dS m-1 added more salts and stressed plant growth. However, the conjunctive use of marginal water at proportional LF could be effective in enhancing the yield potential of crops in water-scarce areas.

The removal of mercury from solid mixed waste using chemical leaching processes

International Nuclear Information System (INIS)

Gates, D.D.; Chao, K.K.; Cameron, P.A.

1995-07-01

The focus of this research was to evaluate chemical leaching as a technique to treat soils, sediments, and glass contaminated with either elemental mercury or a combination of several mercury species. Potassium iodide/iodine solutions were investigated as chemical leaching agents for contaminated soils and sediments. Clean, synthetic soil material and surrogate storm sewer sediments contaminated with mercury were treated with KI/I 2 solutions. It was observed that these leaching solutions could reduce the mercury concentration in soil and sediments by 99.8%. Evaluation of selected posttreatment sediment samples revealed that leachable mercury levels in the treated solids exceeded RCRA requirements. The results of these studies suggest that KI/I 2 leaching is a treatment process that can be used to remove large quantities of mercury from contaminated soils and sediments and may be the only treatment required if treatment goals are established on Hg residual concentrations in solid matrices. Fluorescent bulbs were used to simulate mercury contaminated glass mixed waste. To achieve mercury contamination levels similar to those found in larger bulbs such as those used in DOE facilities a small amount of Hg was added to the crushed bulbs. The most effective agents for leaching mercury from the crushed fluorescent bulbs were KI/I 2 , NaOCl, and NaBr + acid. Radionuclide surrogates were added to both the EPA synthetic soil material and the crushed fluorescent bulbs to determine the fate of radionuclides following chemical leaching with the leaching agents determined to be the most promising. These experiments revealed that although over 98% of the dosed mercury solubilized and was found in the leaching solution, no Cerium was measured in the posttreatment leaching solution. This finding suggest that Uranium, for which Ce was used as a surrogate, would not solubilize during leaching of mercury contaminated soil or glass

Chemical treatment of coal by grinding and aqueous caustic leaching

Energy Technology Data Exchange (ETDEWEB)

Balaz, P.; LaCount, R.B.; Kern, D.G.; Turcaniova, L. [Slovak Academy of Sciences, Kosice (Slovakia). Inst. of Geotechnics

2001-04-01

The aim of this work has been to point out the possibility of using GACL process for chemical cleaning of brown coal Nivaky (Slovakia) and Pittsburgh coal. Simultaneous grinding and aqueous chemical leaching, which is the principle of the process, reduces the inorganic and inorganic sulfur content in both coals. Dearsenificiation nearly up to 96% is detected in GACL-treated samples of Novaky coal. The possibility of enhancing the recovery of humic acid as a consequence of GACL treatment is demonstrated. The process under study works under atmospheric pressure, temperature of 90{degree}C and NaOH consumption, which is six times lower compared with the MCL process. Further research is needed to minimize the wear of grinding media and to improve the washing step. 24 refs., 7 figs., 3 tabs.

Reducing uranium and thorium level in Zircon: effect of heat treatment on rate of leaching

International Nuclear Information System (INIS)

Meor Yusoff Meor Sulaiman

2002-01-01

Considerable amount of uranium and thorium are found in Malaysian zircon and the level is much higher than the minimum value adopted by many importing countries. Selective leaching had been applied as an important technique to reduce these elements. An initial study was carried out using hydrochloric acid leaching system but the result was not favourable. The rate of uranium and thorium leached can be further improved by introducing a heat pretreatment process prior to leaching (Author)

Ni, Co recovery study and Fe by acid leaching in columns; Estudio de la extraccion de Ni, Co y Fe en lateritas por medio de lixiviacion acida en columnas

Energy Technology Data Exchange (ETDEWEB)

Yorio, C. di; Betancourt, E.; Vivas, R.; Rus, J.

2006-07-01

In the following work the possibility of the mic kel recovery by hydrometallurgy extraction for nickeliferous laterite is studied. The work looks for to study the technical viability of the extraction of nickel and cobalt by means of the application of heap leaching. The ore is chemically and physically characterized with the purpose of analyzes its composition and mineral phase, by means of x-rays diffraction, quantitative chemical analysis and elementary chemical analysis by electronic microscopy. One the ore is characterized, it is mixed with sulfuric acid to relations 0.05; 0.1 and 0.2 g acid/g to agglomerated pellets and paste, with the aim to improve the percolation in column, due to the argillaceous nature of the ore leaching rate ranged from 0.305 to 1.06 x 10 l/h m''2 and in the agglomerate condition of the percolation l/h m''2 improves at interval 3.05 to 6.11 x 100 l/h m''2. (Author)

Substrate induced respiration in soils developed under four stages of succession on a colliery heap

Czech Academy of Sciences Publication Activity Database

Szili-Kovács, T.; Elhottová, Dana

2007-01-01

Roč. 35, č. 2 (2007), s. 1169-1172 ISSN 0133-3720 R&D Projects: GA MŠk LC06066 Institutional research plan: CEZ:AV0Z60660521 Keywords : respiration * soils * colliery heap Subject RIV: EH - Ecology, Behaviour Impact factor: 1.190, year: 2007

Leaching of concrete : the leaching process : extrapolation of deterioration : effect on the structural stability

OpenAIRE

Fagerlund, Göran

2000-01-01

The leaching process when water attacks concrete, and the effect of leaching on the strength and durability of a concrete structure, is analysed theoretically. Technique for prediction of the future leaching and structural stability is outlined. The analysis is to a certain extent supported by data from literature. The leaching process is divided in five different types: 1: Pure surface leaching 2: Surface leaching involving erosion 3: Homogeneous leaching over the entire structure 4...

Influence of antioxidants synthesized by plants on physico-chemical and microbiological evolution of Callovo-Oxfordian clay material

International Nuclear Information System (INIS)

Ubersfeld, Dimitri

2016-01-01

This study is a part of the deep disposal site development for radioactive waste in Meuse-Haute Marne (France), most specifically on the bio-physico-chemical conversion of sedimentary clay rocks (Callovo- Oxfordian, COx), excavated and stored on surface in the form of heap. During the experimental and operational phases, several million cubic meters of argillite will be excavated. Argillite stored in the open air will be exposed to meteoritic alterations, oxidizing conditions of surface and colonized biologically (plants, bacteria, fungi). The aim of the thesis is to study the impact of naturally derived antioxidants from revegetation of heap with antioxidant-producing plants on the physical, chemical or microbial weathering processes of argillite. This work was designed to (i) identify suitable naturally derived antioxidants and the plants to produce them (ii) assess the antioxidant inhibitory effects on weathering and leaching COx metals in the laboratory, (iv) field test selected plants on the heap, (iii) follow in situ physicochemical and microbiological evolution of the argillite heap planted with antioxidant producing plants. In the laboratory, percolating model antioxidants of Lamiaceae (linalool, thymol, carvacrol) through a packed column of argillite showed variable water weathering/leaching rate depending on the metal elements present; very low for aluminum (<1 o/oo), between 1-3% for other metals (Ca, Mg, Fe...) and reach more than 60% for sodium. With thymol at 20 mg/l for 3 months, it was found that there are a decrease in sulfur leached amount and the metal elements from the sulfides (Fe, As) and carbonates (Ca, Sr) and inhibition of bacterial and fungal microflora growths. However, intake of artificial root exudates in columns stimulates microbial growth, improves the availability of aluminum, iron and provides sequestration of calcium. Among the tested plants, lavender and lavandin were selected. Two successive plantation tests were carried out in

Natural attenuation in a slag heap contaminated with cadmium: The role of plants and arbuscular mycorrhizal fungi

International Nuclear Information System (INIS)

Gonzalez-Chavez, M.C.; Carrillo-Gonzalez, R.; Gutierrez-Castorena, M.C.

2009-01-01

A field study of the natural attenuation occurring in a slag heap contaminated with high available cadmium was carried out. The aims of this research were: to determine plants colonizing this slag heap; to analyze colonization and morphological biodiversity of spores of arbuscular mycorrhizal fungi (AMF); to determine spore distribution in undisturbed samples; to know mycelium and glomalin abundance in the rhizosphere of these plants, and to investigate glomalin participation in Cd-stabilization. Forming vegetal islands, 22 different pioneering plant species from 11 families were colonizing the slag heap. The most common plants were species of Fabaceae, Asteraceae and Poaceae. Almost all plants were hosting AMF in their roots, and spores belonging to Gigaspora, Glomus, Scutellospora and Acaulospora species were observed. Micromorphological analysis showed that spores were related to decomposing vegetal residues and excrements, which means that mesofauna is contributing to their dispersion in the groundmass. Mycelium mass ranged from 0.11 to 26.3 mg/g, which contained between 13 and 75 mg of glomalin/g. Slag-extracted total glomalin was between 0.36 and 4.74 mg/g. Cadmium sequestered by glomalin extracted from either slag or mycelium was 0.028 mg/g. The ecological implication of these results is that organisms occupying vegetal patches are modifying mine residues, which contribute to soil formation

Natural attenuation in a slag heap contaminated with cadmium: The role of plants and arbuscular mycorrhizal fungi

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Chavez, M.C. [Programa de Edafologia. Colegio de Postgraduados en Ciencias Agricolas, Campus Montecillo. Carretera Mexico-Texcoco, km 36.5. Montecillo, Texcoco, Mexico, 56230 (Mexico)], E-mail: carmeng@colpos.mx; Carrillo-Gonzalez, R.; Gutierrez-Castorena, M.C. [Programa de Edafologia. Colegio de Postgraduados en Ciencias Agricolas, Campus Montecillo. Carretera Mexico-Texcoco, km 36.5. Montecillo, Texcoco, Mexico, 56230 (Mexico)

2009-01-30

A field study of the natural attenuation occurring in a slag heap contaminated with high available cadmium was carried out. The aims of this research were: to determine plants colonizing this slag heap; to analyze colonization and morphological biodiversity of spores of arbuscular mycorrhizal fungi (AMF); to determine spore distribution in undisturbed samples; to know mycelium and glomalin abundance in the rhizosphere of these plants, and to investigate glomalin participation in Cd-stabilization. Forming vegetal islands, 22 different pioneering plant species from 11 families were colonizing the slag heap. The most common plants were species of Fabaceae, Asteraceae and Poaceae. Almost all plants were hosting AMF in their roots, and spores belonging to Gigaspora, Glomus, Scutellospora and Acaulospora species were observed. Micromorphological analysis showed that spores were related to decomposing vegetal residues and excrements, which means that mesofauna is contributing to their dispersion in the groundmass. Mycelium mass ranged from 0.11 to 26.3 mg/g, which contained between 13 and 75 mg of glomalin/g. Slag-extracted total glomalin was between 0.36 and 4.74 mg/g. Cadmium sequestered by glomalin extracted from either slag or mycelium was 0.028 mg/g. The ecological implication of these results is that organisms occupying vegetal patches are modifying mine residues, which contribute to soil formation.

Treatment of solid waste highly contaminated by alpha emitters low-temperature impact crushing/leaching and incineration

International Nuclear Information System (INIS)

Carpentier, S.; Bertolotti, G.

1986-01-01

Reprocessing plants, hot laboratories, fuel fabrication plants all produce waste containing residual quantities of plutonium and uranium in oxide form which often reach some tens of grammes per m 3 . Appropriate treatment recovers an appreciable amount of fissile material, which could lead to the waste being declassified and able to be disposed of in near ground-level facilities. After a summary sorting at production level, waste can be sent to a low-temperature impact crushing/leaching unit which considerably reduces volumes to be stored. We call this process cryo-crushing/leaching. For burnable crushed particles, a further volume reduction may be obtained by incineration, an operation which is made easier by the low fissile material residue content. Incineration can, of course also be applied directly to burnable solid waste sorted at source and crushed following more conventional methods [fr

Chapter 14: Evaluating the Leaching of Biocides from Preservative-Treated Wood Products

Science.gov (United States)

Stan T. Lebow

2014-01-01

Leaching of biocides is an important consideration in the long term durability and any potential for environmental impact of treated wood products. This chapter discusses factors affecting biocide leaching, as well as methods of evaluating rate and quantity of biocide released. The extent of leaching is a function of preservative formulation, treatment methods, wood...

BACTERIAL LEACHING OF ELECTRONIC SCRAP: INFLUENCE OF PROCESS PARAMETERS

Directory of Open Access Journals (Sweden)

Luciana Harue Yamane

2013-03-01

Full Text Available The application of bacterial leaching in the ore treatment is already known and also can be applied such as treatment of electronic waste to copper recovery. This paper investigates the influence of process parameters (pulp density, inoculums volume, rotation speed and initial concentration of ferrous iron on bacterial leaching of copper from printed circuit board of computers using the bacterium Acidithiobacillus ferrooxidans–LR. Printed circuit boards from computers were comminuted using a hammer mill. The powder obtained was magnetically separated and the non-magnetic material used in this study. A shake flask study was carried out on the non-magnetic material using a shaker. The results show that Acidithiobacillus ferrooxidans–LR can leach 99% of copper from printed circuit boards (non–magnetic material under the determined conditions through of the studies.

Mine water treatment with yellowcake by-production

International Nuclear Information System (INIS)

Csicsak, J.; Csoevari, M.; Eberfalvy, J.; Lendvai, Zs.

2002-01-01

Mining and milling of uranium ore in Hungary was terminated at the end of 1997. From that time rehabilitation works have been carrying out, which include manly the relocation of different solid wastes, such as waste rocks, heap leached residues, demolishing of former industrial buildings, clean up contaminated sites. Overall rehabilitation of the tailings ponds has also started. At first step the ground water restoration system is under construction, aiming at protecting the drinking water aquifer situated in the immediate vicinity of the tailings ponds. Former mining activity has been carried out also in the vicinity of the drinking water catchment area, for protection of that is compulsory to maintain appropriate depression in the mine in question. This means that mine water has to be pumped out continuously and because of the elevated uranium concentration in mine water, the water has to be treated. Thus the water quality protection is connected with uranium removal from the mine water. Mine water treatment process developed is based on anion-exchange process and removal of the uranium from the eluates with hydrogen peroxide. (author)

Comparison of leaching tests and study of leaching mechanisms

International Nuclear Information System (INIS)

Amarantos, S.G.; Papadokostaki, K.G.; Petropoulos, J.H.

1985-10-01

The present work is concerned first with the study of certain aspects of the leaching kinetics of Cs + and Sr ++ embedded in cement, as Cs 2 SO 4 and SrSO 4 , and in particular: (a) the comparative evaluation of leaching in (i) stagnant, (ii) stirred and (iii) continuously flowing (modified Soxhlet) water, (b) the effect of atmospheric CO 2 on elution, (c) the effect of temperature changes during leaching. Secondly, model kinetic studies were carried out using cellulose acetate incorporating SrSO 4 , CaSO 4 or NaCl. The main results obtained were: (1) Cs leaching rates were not significantly affected by the leaching method or by the presence of atmospheric CO 2 . The embedded Cs exists in relatively easily leachable and less rapidly leachable (most probably located within the gel regions) forms. (2) Elution of Sr is retarded by stagnant and infrequently renewed leachant (method (i)) and by the presence of atmospheric CO 2 ; leaching method (iii), which tends to minimize both of these effects, gave the highest elution rates. (3) The observed elution kinetics in the case of cellulose acetate-CaSO 4 or SrSO 4 conform to the Higuchi model, but a more elaborate theory is needed for the cellulose acetate-NaCl system. (author)

Leaching mechanisms

International Nuclear Information System (INIS)

Dougherty, D.R.; Colombo, P.

1984-01-01

Sufficient data are lacking to provide a basis for adequately assessing the long term leaching behavior of solidified low level radioactive waste forms in their disposal environment. Although the release of radioactivity from a waste form to an aqueous environment is recognized to be due to one or more mechanisms such as diffusion, dissolution, corrosion or ion exchange, the leaching mechanisms and the factors which control the leaching behavior of waste forms are not fully understood. This study will determine the prevailing mechanisms for a variety of selected LLW solidification agents which are being considered for use by defense and commercial generators and which will cover the broadest possible number of mechanisms. The investigation will proceed by the postulation of mathematical models representative of the prevailing mechanism(s) and the use of statistically designed experiments to test the actual leaching behavior of laborattory samples against the postulated representations. Maximum use of existing leach data in the literature will be made by incorporating literature results into a computerized data base along with the experimental results generated in this task

The ultrasonically assisted metals recovery treatment of printed circuit board waste sludge by leaching separation.

Science.gov (United States)

Xie, Fengchun; Li, Haiying; Ma, Yang; Li, Chuncheng; Cai, Tingting; Huang, Zhiyuan; Yuan, Gaoqing

2009-10-15

This paper provides a practical technique that realized industrial scale copper and iron separation from printed circuit board (PCB) waste sludge by ultrasonically assisted acid leaching in a low cost, low energy consumption and zero discharge of wastes manner. The separation efficiencies of copper and iron from acid leaching with assistance of ultrasound were compared with the one without assistance of ultrasound and the effects of the leaching procedure, pH value, and ultrasonic strength have been investigated in the paper. With the appropriate leaching procedure, a final pH of 3.0, an ultrasonic generator power of 160 W (in 1l tank), leaching time of 60 min, leaching efficiencies of copper and iron had reached 97.83% and 1.23%, respectively. Therefore the separation of copper and iron in PCB waste sludge was virtually achieved. The lab results had been successfully applied to the industrial scaled applications in a heavy metal recovery plant in city of Huizhou, China for more than two years. It has great potentials to be used in even the broad metal recovery practices.

Extraction of nickel from Ramu laterite by sulphation roasting-water leaching

Science.gov (United States)

Wang, Weiwei; Du, Shangchao; Liu, Guo; Tang, Jianwen; Lu, Yeda; Lv, Dong

2017-08-01

Recovery of nickel from a PNG nickel laterite with high content of iron by a sulphation roasting-water leaching has been studied. The influences of sulfuric acid/ore ratio, temperature of roasting and water on recovery efficiency were investigated. The effective separation of nickel over the co-existed elements including iron was achieved by the process with mixing, curing, roasting and leaching stages. Near 100% of nickel was leached from the roasted laterite by water at 80°C in an atmospheric air, while co-leaching of about 2% of iron, under the optimal pre-treatment conditions with the ratio of acid: ore around 0.45:1 and the roasting temperature about 650°C. The advantages and disadvantages of sulphation atmospheric leaching are compared with pressure acid leaching with engineering consideration.

Leaching Test Relationships, Laboratory-to-Field Comparisons and Recommendations for Leaching Evaluation using the Leaching Environmental Assessment Framework (LEAF)

Science.gov (United States)

This report presents examples of the relationships between the results of laboratory leaching tests, as defined by the Leaching Environmental Assessment Framework (LEAF) or analogous international test methods, and leaching of constituents from a broad range of materials under di...

Technical treatment options for the mill effluents of the Los Gigantes Complex

International Nuclear Information System (INIS)

Asenjo, A.R.

2002-01-01

The Mining/Milling Los Gigantes Complex is located in Cordoba Province, about 100 km to the West of the capital city. The uranium mining and milling activities have been carried out during the period between 1980 and 1990. As result of those activities, mine wastes, low grade ore, sludge, heap leach wastes and liquid effluents have been accumulated in the site. At present, the National Atomic Energy Commission of Argentina is developing the Remediation Project of the site. Within the frame of this Project it is necessary to define the liquid effluent treatment methodology of the liquids accumulated in a pond in order to achieve the proper quality to be released to the environment, according with the national and provincial regulations. In this paper several liquid treatment methods are described. These methods were also developed at the lab scale. Among these we can mention hot and cool alcalinization with barium chloride addition and ion exchange resins treatments. Also a pilot scale assay has been done in the site (about 450 m 3 ) in order to verify the obtained lab scale results. Nevertheless that other assays are yet under developing, the obtained results are reported. (author)

Aluminum chloride restoration of in situ leached uranium ores

International Nuclear Information System (INIS)

Grant, D.C.; Burgman, M.A.

1982-01-01

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability

Microbiology of Composting Pig Waste: Comparison of Vermicomposting and Open Heap Techniques

OpenAIRE

Ogefere, H. O.; Ogbimi, A. O.; Omoregie, R.

2010-01-01

Against the background of an effective waste management, microbiological studies of composting pig waste were investigated. Freshly deposited excreta from confined pigs in a private pig farm in Benin City, Edo State, Nigeria were composted by two aerobic methods – vermicomposting and open heap. Microbial (bacterial and fungal) counts and characterization were carried out periodically within the 40 weeks of composting, using standard techniques. The results showed that only duration of compos...

PROBLEMS OF PROTECTION OF URBAN AREAS FROM RADIONUCLIDES STRONTIUM-90 AND CAESIUM-137 AFTER TECHNOLOGICAL DISASTERS

Directory of Open Access Journals (Sweden)

Olga Cheremisina

2017-05-01

Full Text Available The methods of decontamination of radionuclides from soils are considered. The literature focuses on fixing radionuclides in soils and creating geochemical barriers that it is prevent the spread of pollution. The main disadvantage of these methods is exclude the possibility of building a territory. It is need to clean up the area to the sanitary and hygienic requirements for further use and then it is desirable to fix the residual activity. Carried out an analysis of forms of radionuclides fixation in soils and mechanics of this fixation, therewith revealed that Cs-137 fixed more strongly on mineral component of soil, than Sr-90, which is mainly in the acid-soluble and exchangeable form, and, as a consequence, passes into the liquid phase during soil deactivation more easily. Contaminated soil deactivation in the urbanized territory is possible by washing it by ferric chloride solution at a concentration 0.02-0.05 M and with an equimolar addition of an ammonium chloride. Therewith most efficient methods, which used in-situ conditions, are heap and convection leaching technologies with treatment degree, which not less than 80%. At the same time, the most efficient methods which used in-situ conditions are heap and the convection leaching. The hardware-technological scheme of a convection leaching is presented. Noted that ammonium salts additions slightly rising coefficient of treatment from Sr-90. Because ammonium salts aren’t expensive, their additions allow to obtain significant economic benefits due to decreasing of ferric chloride consumption, which is more valuable, and waste water volume reduction.

In-situ uranium leaching

International Nuclear Information System (INIS)

Dotson, B.J.

1986-01-01

This invention provides a method for improving the recovery of mineral values from ore bodies subjected to in-situ leaching by controlling the flow behaviour of the leaching solution. In particular, the invention relates to an in-situ leaching operation employing a foam for mobility control of the leaching solution. A foam bank is either introduced into the ore bed or developed in-situ in the ore bed. The foam then becomes a diverting agent forcing the leaching fluid through the previously non-contacted regions of the deposit

Uranium ore processing in Spain

International Nuclear Information System (INIS)

Josa, J.M.

1976-01-01

The paper presents a review of the Spanish needs of uranium concentrates and uranium ore processing technology and trends in Spain. Spain produces approximately 200t U 3 O 8 /a at two facilities. One plant in the south (Andujar, Jaen) can obtain 70t U 3 O 8 /a and uses a conventional acid leaching process with countercurrent solvent extraction. A second plant, situated in the west (Ciudad Rodrigo, Salamanca) has started in 1975 and has a capacity of 120-130t U 3 O 8 /a, using acid heap leaching and solvent extraction. There is another experimental facility (Don Benito, Badajoz) scheduled to start in 1976 and expected to produce about 25-35t U 3 O 8 /a as a by-product of the research work. For the near future (1978) it is hoped to increase the production with: (a) A new conventional acid leaching/solvent extraction plant in Ciudad Rodrigo; its tentative capacity is fixed at 550t U 3 O 8 /a. (b) A facility in the south, to recover about 130t U 3 O 8 /a from phosphoric acid. (c) Several small mobile plants (30t U 3 O 8 /a per plant); these will be placed near small and isolated mines. The next production increase (1979-1980) will come with the treatment of sandstones (Guadalajara and Cataluna) and lignites(Cataluna); this is being studied. There are also research programmes to study the recovery of uranium from low-grade ores (heap, in-situ and bacterial leaching) and from other industries. (author)

PEP Run Report for Integrated Test A, Caustic Leaching in UFP-VSL-T01A, Oxidative Leaching in UFP-VSL-T02A

International Nuclear Information System (INIS)

Guzman-Leong, Consuelo E.; Bredt, Ofelia P.; Burns, Carolyn A.; Daniel, Richard C.; Su, Yin-Fong; Geeting, John G.H.; Golovich, Elizabeth C.; Josephson, Gary B.; Kurath, Dean E.; Sevigny, Gary J.; Smith, Dennese M.; Valdez, Patrick L.J.; Yokuda, Satoru T.; Young, Joan K.

2009-01-01

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed and constructed and operated as part of a plan to respond to issue M12, 'Undemonstrated Leaching Processes.'(a) The PEP, located in the Process Engineering Laboratory-West (PDLW) located in Richland, Washington, is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

Study on Leaching of Hexavalent Chromium from Hardened Concretes Using Tank Leaching Test

OpenAIRE

Takahashi, Shigeru; Sakai, Etsuo; Sugiyama, Takafumi

2007-01-01

Tank leaching tests were carried out to investigate the behavior of leaching trace elements from monolith samples. This study consists of two series, and the trace element used was hexavalent chromium. In Series I, the influence of the leachant/surface area of the specimen (L/S ratio) on the leaching amount was investigated. The leaching amount was found to increase with the amount of worked water. This shows that any L/S ratio can be selected in the tank leaching test. In Series II, th...

The radiochemical contamination (²¹⁰Po and ²³⁸U) of zone around phosphogypsum waste heap in Wiślinka (northern Poland).

Science.gov (United States)

Boryło, Alicja; Skwarzec, Bogdan; Olszewski, Grzegorz

2012-01-01

The aim of this work was the determination of the impact of phosphogypsum waste heap in Wiślinka (northern Poland) for radiological protection of zone around waste heap. These studies are very important for the estimation of natural alpha radionuclides contents in the vicinity of phosphogypsum waste heap and for environmental pollution assessment of this area. The process of bioaccumulation of radionuclides in interior plants parts prove to examine their origin sources, too. The activity of (210)Po, (234)U, and (238)U were measured using an alpha spectrometer. The values of uranium and polonium concentration in water with immediate area of waste heap are considerably higher than in the waters of the Martwa Wisła river. The values of activity ratio (234)U/(238)U are approximately about one in the phosphogypsum (0.97 ± 0.05) and in the water of retention reservoir and pumping station (0.92 ± 0.01 and 0.99 ± 0.08), while in the water from the Martwa Wisła river they are slightly higher than one (1.03 ± 0.07 and 1.17 ± 0.06). In the analyzed plants species the highest amounts of polonium and uranium were found in ruderal plants samples (between 51 ± 1 and 89 ± 1 for (210)Po; between 36 ± 3 and 68 ± 3 for (238)U) as well as hygrophilous plant samples (18 ± 1 and 84 ± 3; 42 ± 2 and 130 ± 4, respectively for (210)Po and (238)U). The more amounts of (210)Po and (238)U radionuclides were accumulated mainly in the roots of plant species in comparison to green parts. The general conclusion of realized study is higher influence of phosphogypsum on radioactive contamination of environmental zone around heap waste in Wiślinka (northern Poland).

A two-step leaching method designed based on chemical fraction distribution of the heavy metals for selective leaching of Cd, Zn, Cu, and Pb from metallurgical sludge.

Science.gov (United States)

Wang, Fen; Yu, Junxia; Xiong, Wanli; Xu, Yuanlai; Chi, Ru-An

2018-01-01

For selective leaching and highly effective recovery of heavy metals from a metallurgical sludge, a two-step leaching method was designed based on the distribution analysis of the chemical fractions of the loaded heavy metal. Hydrochloric acid (HCl) was used as a leaching agent in the first step to leach the relatively labile heavy metals and then ethylenediamine tetraacetic acid (EDTA) was applied to leach the residual metals according to their different fractional distribution. Using the two-step leaching method, 82.89% of Cd, 55.73% of Zn, 10.85% of Cu, and 0.25% of Pb were leached in the first step by 0.7 M HCl at a contact time of 240 min, and the leaching efficiencies for Cd, Zn, Cu, and Pb were elevated up to 99.76, 91.41, 71.85, and 94.06%, by subsequent treatment with 0.2 M EDTA at 480 min, respectively. Furthermore, HCl leaching induced fractional redistribution, which might increase the mobility of the remaining metals and then facilitate the following metal removal by EDTA. The facilitation was further confirmed by the comparison to the one-step leaching method with single HCl or single EDTA, respectively. These results suggested that the designed two-step leaching method by HCl and EDTA could be used for selective leaching and effective recovery of heavy metals from the metallurgical sludge or heavy metal-contaminated solid media.

Effect of accelerated carbonation and zero valent iron on metal leaching from bottom ash.

Science.gov (United States)

Nilsson, M; Andreas, L; Lagerkvist, A

2016-05-01

About 85% of the ashes produced in Sweden originated from the incineration of municipal solid waste and biofuel. The rest comes from the thermal treatment of recycled wood, peat, charcoal and others. About 68% of all ashes annually produced in Sweden are used for constructions on landfills, mainly slopes, roads and embankments, and only 3% for construction of roads and working surfaces outside the landfills (SCB, 2013). Since waste bottom ash (BA) often has similar properties to crushed bedrock or gravel, it could be used for road constructions to a larger extent. However, the leaching of e.g. Cr, Cu, Mo, Pb and Zn can cause a threat to the surrounding environment if the material is used as it is. Carbonation is a commonly used pre-treatment method, yet it is not always sufficient. As leaching from aged ash is often controlled by adsorption to iron oxides, increasing the number of Fe oxide sorption sites can be a way to control the leaching of several critical elements. The importance of iron oxides as sorption sites for metals is known from both mineralogical studies of bottom ash and from the remediation of contaminated soil, where iron is used as an amendment. In this study, zero valent iron (Fe(0)) was added prior to accelerated carbonation in order to increase the number of adsorption sites for metals and thereby reduce leaching. Batch, column and pHstat leaching tests were performed and the leaching behaviour was evaluated with multivariate data analysis. It showed that leaching changed distinctly after the tested treatments, in particular after the combined treatment. Especially, the leaching of Cr and Cu clearly decreased as a result of accelerated carbonation. The combination of accelerated carbonation with Fe(0) addition reduced the leaching of Cr and Cu even further and reduced also the leaching of Mo, Zn, Pb and Cd compared to untreated BA. Compared with only accelerated carbonation, the Fe(0) addition significantly reduced the leaching of Cr, Cu and Mo

Laboratory study on leaching of a sandstone-type uranium deposit for acid in-situ leaching

International Nuclear Information System (INIS)

Wen Zhenqian; Yao Yixuan; Zheng Jianping; Jiang Yan; Cui Xin; Xing Yongguo; Hao Jinting; Tang Huazhang

2013-01-01

Ore samples were took from in-situ leaching experiment boreholes in a sandstone-type uranium deposit. Technological mineralogy study, agitating leaching and column leaching experiments were carried. The results show that the content of minerals consuming acid and deoxidized minerals is low. When sulfuric acid concentration was 1O g/L, initial uranium content was 0.0224%, and liquid-to-solid ratio was l.91, leaching rate of column leaching experiments is 89.19%, acid consumption is 8.2 kg/t ore, acid consumption is 41.88 t/tU. Acid leaching, technology is recommend for field in-situ leaching experiment, sulfuric acid concentration in confecting solution is 10 g/L, and oxidizing agent is needless during leaching process. (authors)

Accelerated leach test development program

International Nuclear Information System (INIS)

Fuhrmann, M.; Pietrzak, R.F.; Heiser, J.; Franz, E.M.; Colombo, P.

1990-11-01

In FY 1989, a draft accelerated leach test for solidified waste was written. Combined test conditions that accelerate leaching were validated through experimental and modeling efforts. A computer program was developed that calculates test results and models leaching mechanisms. This program allows the user to determine if diffusion controls leaching and, if this is the case, to make projections of releases. Leaching mechanisms other than diffusion (diffusion plus source term partitioning and solubility limited leaching) are included in the program is indicators of other processes that may control leaching. Leach test data are presented and modeling results are discussed for laboratory scale waste forms composed of portland cement containing sodium sulfate salt, portland cement containing incinerator ash, and vinyl ester-styrene containing sodium sulfate. 16 refs., 38 figs., 5 tabs

Transient response in granular quasi-two-dimensional bounded heap flow.

Science.gov (United States)

Xiao, Hongyi; Ottino, Julio M; Lueptow, Richard M; Umbanhowar, Paul B

2017-10-01

We study the transition between steady flows of noncohesive granular materials in quasi-two-dimensional bounded heaps by suddenly changing the feed rate. In both experiments and simulations, the primary feature of the transition is a wedge of flowing particles that propagates downstream over the rising free surface with a wedge front velocity inversely proportional to the square root of time. An additional longer duration transient process continues after the wedge front reaches the downstream wall. The entire transition is well modeled as a moving boundary problem with a diffusionlike equation derived from local mass balance and a local relation between the flux and the surface slope.

PEP Run Report for Integrated Test A, Caustic Leaching in UFP-VSL-T01A, Oxidative Leaching in UFP-VSL-T02A

Energy Technology Data Exchange (ETDEWEB)

Guzman-Leong, Consuelo E.; Bredt, Ofelia P.; Burns, Carolyn A.; Daniel, Richard C.; Su, Yin-Fong; Geeting, John GH; Golovich, Elizabeth C.; Josephson, Gary B.; Kurath, Dean E.; Sevigny, Gary J.; Smith, Dennese M.; Valdez, Patrick LJ; Yokuda, Satoru T.; Young, Joan K.

2009-12-04

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed and constructed and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes.”(a) The PEP, located in the Process Engineering Laboratory-West (PDLW) located in Richland, Washington, is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

Colonization of colliery spoil heaps by millipedes (Diplopoda) and terrestrial isopods (Oniscidea) in the Sokolov region, Czech Republic

Czech Academy of Sciences Publication Activity Database

Tajovský, Karel

2001-01-01

Roč. 9, č. 4 (2001), s. 365-369 ISSN 1061-2971 Institutional research plan: CEZ:AV0Z6066911 Keywords : colliery spoil heaps * succession * rekultivation Subject RIV: EH - Ecology, Behaviour Impact factor: 1.011, year: 2001

Ultrasound-assisted HCl-NaCl leaching of lead-rich and antimony-rich oxidizing slag.

Science.gov (United States)

Zhang, Rong Liang; Zhang, Xiao Fei; Tang, Shu Zhen; Huang, Ai Dong

2015-11-01

Lead-rich and antimony-rich oxidizing slag was subjected to regular HCl-NaCl leaching, with the experimental conditions optimized under which ultrasound was introduced. After only 15 min of ultrasound-assisted leaching, the leaching rate of Sb resembled that after 45 min of regular leaching. Ultrasonic treatment considerably elevated the leaching rates of Sb and Pb, and shortened the leaching time. With the decrease of particle size, the leaching rate of Sb and Pb increased gradually. Especially, as the particle size of the slag was greater than 0.217 mm, the ultrasonic leaching effects of Sb and Pb were significantly higher than that of regular leaching effects. The temperature exhibited great effect on ultrasonic leaching performance. As the temperature increased, the leaching rates of Sb and Pb increased step by step. In case the temperature was higher than 85°C, the increasing speed of the leaching rates for Sb and Pb tended to be slow. Increasing ultrasonic power could augment the leaching rate or accelerate the procedure till the same leaching rate. However, since ultrasound failed to energize the formation of new reaction pathways, the maximum leaching rates of Sb and Pb were determined by their phase compositions rather than by ultrasonic field. Copyright © 2015 Elsevier B.V. All rights reserved.

Glass leaching performance

International Nuclear Information System (INIS)

Chick, L.A.; Turcotte, R.P.

1983-05-01

Current understanding of the leaching performance of high-level nuclear waste (HLW) glass is summarized. The empirical model of waste glass leaching behavior developed shows that at high water flow rates the glass leach rate is kinetically limited to a maximum value. At intermediate water flow rates, leaching is limited by the solution concentration of silica and decreases with decreasing water flow rates. Release of soluble elements is controlled by silica dissolution because silica forms the binding network of the glass. At low water flow rates, mass loss rates reach values controlled by formation rates of alteration minerals, or by diffusion of dissolution products through essentially stagnant water. The parameters reviewed with respect to their quantifiable influence on leaching behavior include temperature, pH, leachant composition, glass composition, thermal history, and radiation. Of these, temperature is most important since the rate of mass loss approximately doubles with each 10 0 C increase in dilute solutions. The pH has small effects within the 4 to 10 range. The chemical composition of the leachant is most important with regard to its influence on alteration product formation. Glass composition exhibits the largest effects at high flow rates where improved glasses leach from ten to thirty times slower than glass 76 to 68. The effects of the thermal history (devitrification) of the glass are not likely to be significant. Radiation effects are important primarily in that radiolysis can potentially drive pH values to less than 4. Radiation damage to the glass causes insignificant changes in leaching performance

Advanced mercury removal from gold leachate solutions prior to gold and silver extraction: a field study from an active gold mine in Peru.

Science.gov (United States)

Matlock, Matthew M; Howerton, Brock S; Van Aelstyn, Mike A; Nordstrom, Fredrik L; Atwood, David A

2002-04-01

Mercury contamination in the Gold-Cyanide Process (GCP) is a serious health and environmental problem. Following the heap leaching of gold and silver ores with NaCN solutions, portions of the mercury-cyano complexes often adhere to the activated carbon (AC) used to extract the gold. During the electrowinning and retorting steps, mercury can be (and often is) emitted to the air as a vapor. This poses a severe health hazard to plant workers and the local environment. Additional concerns relate to the safety of workers when handling the mercury-laden AC. Currently, mercury treatment from the heap leach solution is nonexistent. This is due to the fact that chelating ligands which can effectively work under the adverse pH conditions (as present in the heap leachate solutions) do not exist. In an effort to economically and effectively treat the leachate solution prior to passing over the AC, a dipotassium salt of 1,3-benzenediamidoethanethiol (BDET2-) has been developed to irreversibly bind and precipitate the mercury. The ligand has proven to be highly effective by selectively reducing mercury levels from average initial concentrations of 34.5 ppm (parts per million) to 0.014 ppm within 10 min and to 0.008 ppm within 15 min. X-ray powder diffraction (XRD), proton nuclear magnetic resonance (1H NMR), Raman, and infrared (IR) spectroscopy demonstrate the formation of a mercury-ligand compound, which remains insoluble over pH ranges of 0.0-14.0. Leachate samples from an active gold mine in Peru have been analyzed using cold vapor atomic fluorescence (CVAF) and inductively coupled plasma optical emission spectroscopy (ICP-OES) for metal concentrations before and after treatment with the BDET2- ligand.

Information Management of Health and Safety at the Tarkwa Mine of ...

African Journals Online (AJOL)

Michael

2016-06-01

Jun 1, 2016 ... Information Management of Health and Safety at the Tarkwa ... heap leach technology. ... the quality of information was assessed using the content of information ..... managing library users' expectations; and reference service.

Leaching Mechanisms Program. Annual report

International Nuclear Information System (INIS)

Dougherty, D.; Colombo, P.; Doty, R.; Fuhrmann, M.

1984-09-01

The primary goal of this work is to determine the leaching mechanisms of a variety of matrix materials either in use or being considered for the solidification of low-level radioactive wastes by defense and commercial waste generators. Since this program is new and did not formally begin until May of FY 84, the results reported here are few and preliminary. Efforts were concentrated in the following activities: (1) The literature search for leaching data and proposed leaching models and mechanisms for low-level waste. (2) Data base development for leaching data being compiled from the literature and from the leaching experiments in this program. (3) The selection of solidification agents for the experimental part of the program. (4) Fabrication of leach samples and initiation of leach testing. 28 references, 9 figures, 4 tables

Technological project of serpentine raw material milling from Dobšiná heaps

Directory of Open Access Journals (Sweden)

Alena Pietriková

2005-11-01

Full Text Available Serpentine heaps in the surrounding of Dobšiná are an old ecological problem of the city and at the same time a suitable material for the production of MgCl2 and SiO2. The technology of the production is based on the chemical processing of the raw material, which is preceded by the raw material preparation comprising of the mechanical and hydraulic sorting, milling and the magnetic separation operations.

Effect of biotic and abiotic factors on soil microbial community diversity during primary succession on colliery spoil heaps

Czech Academy of Sciences Publication Activity Database

Elhottová, Dana; Frouz, Jan; Chroňáková, Alica; Malý, S.; Krištůfek, Václav; Kalčík, Jiří; Szili-Kovács, T.; Picek, T.

2004-01-01

Roč. 45, - (2004), s. 51 ISSN 0009-0646. [Kongres československé společnosti mikrobiologické /23./. 06.09.2004-09.09.2004, Brno] Keywords : soil microbial community * primary succession * colliery spoil heaps Subject RIV: EH - Ecology, Behaviour

Ultrasound augmented leaching of nickel sulfate in sulfuric acid and hydrogen peroxide media.

Science.gov (United States)

Li, Haoyu; Li, Shiwei; Peng, Jinhui; Srinivasakannan, Chandrasekar; Zhang, Libo; Yin, Shaohua

2018-01-01

A new method of preparation high purity nickel sulfate assisted by ultrasonic was studied. The process mechanism was analyzed by Inductively Coupled Plasma (ICP), X-ray diffraction (XRD), Scanning electron microscopy (SEM), and Energy dispersive X-ray spectrometry (EDS).The reaction mechanisms of oxidizing leaching and ultrasonic leaching were explored, respectively. Results showed that ultrasonic treatment peel off the oxide film on the surface of nickel. The leachate under strongly agitated, the yield rate of nickel sulfate was accelerate. And the reaction area was increased by the cavitation effect, the liquid-solid reaction was promoted, and the activation energy was reduced. The leaching rate of nickel reached 46.29% by conventional leaching, which takes about 5h. Under the same conditions, the ultrasonic leaching rate reached 40%, only half of the conventional leaching time. Concentration of leaching agent, reaction temperature, ultrasonic power, leaching time had significant effect on the enhancement of the leaching reaction with ultrasonic radiation. The leaching rate of 60.41% under the optimum experiment conditions as follows: sulfuric acid concentration 30%, hydrogen peroxide 10%, leaching temperature 333K, ultrasonic power 200W and leaching time 4h. The kinetic study of the system was investigated, and the reaction rates of conventional leaching and ultrasonic leaching were controlled by diffusion, and the apparent activation energies were 16.2kJ/mol and 11.83kJ/mol. Copyright © 2017. Published by Elsevier B.V.

XRF and leaching characterization of waste glasses derived from wastewater treatment sludges

International Nuclear Information System (INIS)

Ragsdale, R.G., Jr.

1994-12-01

Purpose of this study was to investigate use of XRF (x-ray fluorescence spectrometry) as a near real-time method to determine melter glass compositions. A range of glasses derived from wastewater treatment sludges associated with DOE sites was prepared. They were analyzed by XRF and wet chemistry digestion with atomic absorption/inductively coupled emission spectrometry. Results indicated good correlation between these two methods. A rapid sample preparation and analysis technique was developed and demonstrated by acquiring a sample from a pilot-scale simulated waste glass melter and analyzing it by XRF within one hour. From the results, XRF shows excellent potential as a process control tool for waste glass vitrification. Glasses prepared for this study were further analyzed for durability by toxicity characteristic leaching procedure and product consistency test and results are presented

Leaching of metals from soil contaminated by mining activities.

Science.gov (United States)

Yukselen, M A; Alpaslan, B

2001-10-12

Stabilization/solidification (s/s) is one of the most effective methods of dealing with heavy metal contaminated sites. The ability of lime and cement stabilization to immobilize Pb, Cu and Fe contained in a contaminated soil originating from an old mining and smelting area located along the Mediterranean Sea shore in northern Cyprus was investigated. The stabilization was evaluated by applying leaching tests. A series of tests were conducted to optimize the additive soil ratio for the best immobilization process. Additive/soil=1/15 (m/m) ratio was found to be the optimum for both lime and cement. Application of the US EPA toxicity characteristic leaching procedure (TCLP) on the soil samples treated with lime at additive/soil=1/15 (m/m) mixing ratios showed that Cu and Fe solubility was reduced at 94 and 90%, respectively. The results of cement treatment using the same ratio, reduced the solubility 48 and 71% for Cu and Fe, respectively. The Pb solubility was found to be below the regulatory limit of 5mg/l so no additive treatment was needed. The optimum additive/soil amount (1/15) was selected for more detailed column studies, that were carried out in the acidic pH range. According to the results of column leaching tests, it was found that, the degree of heavy metal leaching is highly dependent on pH.

Bacterial leaching of waste uranium materials.

Science.gov (United States)

Barbic, F F; Bracilović, D M; Krajincanić, B V; Lucić, J L

1976-01-01

The effect of ferrobacteria and thiobacteria on the leaching of waste uranium materials from which 70-80% of uranium was previously leached by classical chemical hydrometallurgical procedure has been investigated. The bacteria used are found in the ore and the mine water of Zletovska River locality, Yugoslavia. Parameters of biological leaching were examined in the laboratory. Leaching conditions were changed with the aim of increasing the amount of uranium leached. The effect of pyrite added to the waste materials before the beginning of leaching has also been examined. Uranium leaching is directly proportional to the composition and number of ferrobacteria and thiobacteria, and increased by almost twice the value obtained from the same starting materials without using bacteria. Increased sulphuric acid concentrations stimulate considerably the rate of leaching. Uranium leaching is increased up to 20% while sulphuric acid consumption is simultaneously decreased by the addition of pyrite. Uranium concentrations in starting waste materials used for leaching were extremely low (0.0278 and 0.372% U) but about 60% recovery of uranium was obtained, with relatively low consumption of sulphuric acid.

Bacterial leaching of waste uranium materials

International Nuclear Information System (INIS)

Barbic, F.F.; Bracilovic, D.M.; Krajincanic, B.V.; Lucic, J.L.

1976-01-01

The effect of ferrobacteria and thiobacteria on the leaching of waste uranium materials from which 70-80% of uranium was previously leached by classical chemical hydrometallurgical procedure has been investigated. The bacteria used are found in the ore and the mine water of Zletovska River locality, Yugoslavia. Parameters of biological leaching were examined in the laboratory. Leaching conditions were changed with the aim of increasing the amount of uranium leached. The effect of pyrite added to the waste materials before the beginning of leaching has also been examined. Uranium leaching is directly proportional to the composition and number of ferrobacteria and thiobacteria, and increased by almost twice the value obtained from the same starting materials without using bacteria. Increased sulphuric acid concentrations stimulate considerably the rate of leaching. Uranium leaching is increased up to 20% while sulphuric acid consumption is simultaneously decreased by the addition of pyrite. Uranium concentrations in starting waste materials used for leaching were extremely low (0.0278 and 0.0372% U) but about 60% recovery of uranium was obtained, with relatively low consumption of sulphuric acid. (author)

In situ leaching of uranium

International Nuclear Information System (INIS)

Martin, B.

1980-01-01

A process is described for the in-situ leaching of uranium-containing ores employing an acidic leach liquor containing peroxymonosulphuric acid. Preferably, additionally, sulphuric acid is present in the leach liquor. (author)

Acid leaching of mixed spent Li-ion batteries

Directory of Open Access Journals (Sweden)

A.A. Nayl

2017-05-01

Full Text Available Acid leaching for different types of mixed spent Li-ion mobile batteries is carried out after alkali decomposition using NH4OH followed by H2SO4 + H2O2 leaching. In the alkali decomposition step, the effects of reaction time, NH4OH concentration, liquid/solid mass ratio and reaction temperature on the decomposition process are investigated to remove Al, Cu, Mn, Ni, Co, and Li. After alkaline treatment, the alkali paste is treated to leach the remaining metals using H2SO4 + H2O2. The significant effects of reaction time, acid concentration, H2O2 concentration, liquid/solid mass ratios and reaction temperature on the leaching rate are studied. More than 97% of Al, Mn, Ni, Co, and Li and about 65% Cu are leached in two stages. Kinetic analysis shows that, the data fit with chemical reaction control mechanism and the activation energies for the investigated metals using the Arrhenius equation ranged from 30.1 to 41.4 kJ/mol. Recovered metals are precipitated from the leaching liquor at varying pH values using NaOH solution and Na2CO3. Firstly, Mn is precipitated as MnCO3 at pH = 7.5. Secondly, at pH = 9.0, nickel is precipitated as NiCO3. Thirdly, as the pH of the leaching liquor reaches 11–12, Co(OH2 is precipitated and the remaining Li is readily precipitated as Li2CO3 using a saturated Na2CO3 solution. Based on the experimental data, a flow sheet is developed and tested for the recovery process.

Novel Binders and Methods for Agglomeration of Ore

Energy Technology Data Exchange (ETDEWEB)

S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

2006-12-31

Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking. This project has identified several acid-resistant binders and agglomeration procedures that can be used for improving the energy efficiency of heap leaching, by preventing the ''ponding'' and ''channeling'' effects that currently cause reduced recovery and extended leaching cycle times. Methods have also been developed for iron ore

Study of the sulfuric acid leaching and bacterial leaching of low grade uranium ore by orbital shaker experiment

International Nuclear Information System (INIS)

Li Guangyue; Liu Yulong; Wang Yongdong; Ding Dexin

2009-01-01

The sulphuric acid leaching and bacteria leaching by orbital shaker experiments were conducted for the low grade uranium ore from a uranium mine in Guangdong Province. The results show that, when the concentration of sulphuric acid and that of slurry were 30 g/L and 25%, respectively, the conditions were most favourable for sulphuric acid leaching and the rate of leaching reached 92.92%, that, when pH value was 1.5, inoculation amount, 10%, concentration of slurry, 10%, the conditions were most favourable for bacteria leaching and the rate of leaching reached 95.93%, that, compared with sulphuric acid leaching, bacteria leaching decreased sulphuric acid consumption by 17.2% and increased the rate of leaching by 3%, and that, under the most favourable conditions for suphuric acid leaching, if 1% natrium chlorate was added, the rate of leaching increased to 96.46%, but 10 kg of natrium chlorate was consumed for 1 ton of uranium ore. (authors)

Presence and leaching of bisphenol a (BPA) from dental materials

Science.gov (United States)

Becher, Rune; Wellendorf, Hanne; Sakhi, Amrit Kaur; Samuelsen, Jan Tore; Thomsen, Cathrine; Bølling, Anette Kocbach; Kopperud, Hilde Molvig

2018-01-01

Abstract BPA has been reported to leach from some resin based dental restorative materials and materials used for orthodontic treatment. To confirm and update previous findings, especially in light of the new temporary lower threshold value for tolerable daily BPA intake, we have investigated the leaching of BPA from 4 composite filling materials, 3 sealants and 2 orthodontic bonding materials. The materials were either uncured and dissolved in methanol or cured. The cured materials were kept in deionized water for 24 hours or 2 weeks. Samples were subsequently analyzed by ultra-performance liquid chromatography coupled to mass spectrometry (UPLC-MS-MS). The composite filling material Tetric EvoFlow® and the fissure sealant DELTON® showed significantly higher levels of BPA leaching compared to control samples for all test conditions (uncured, 24 h leaching and 2 weeks leaching). There were no significant differences in amount of leached BPA for any of the tested materials after 24 hours compared to 2 weeks. These results show that BPA is still released from some dental materials despite the general concern about potential adverse effects of BPA. However, the amounts of BPA were relatively low and most likely represent a very small contribution to the total BPA exposure. PMID:29868625

Application of alkaline leaching to the extraction of uranium from shale of the Vosges

International Nuclear Information System (INIS)

Mouret, P.; Pottier, P.; Le Bris, J.

1958-01-01

Description of chemical treatment of Vosges shales to obtain uranium by alkaline leaching. Mineralogy aspects of ore, physical and chemical conditions of leaching, solid/liquid separation, uranium recovery by either ion exchange process or electrolytic precipitation. (author) [fr

Brooks under colliery heaps in the Walloon Region

Energy Technology Data Exchange (ETDEWEB)

Lardinois, J.P. [IGRETEC, Charleroi (Belgium); Flamion, B. [Mines et Geologie, Dir. Generale des Ressources Naturelles et de l' Environnement. Dir. des Eaux Souterraines, Jambes (Belgium); Zech, Y. [Universite Catholique de Louvain, Unite de Genie civil, Louvain-La-Neuve (Belgium)

2005-07-01

Several studies are presently under progress in the Walloon Region so as to assess the long term environmental impact caused by the closing of coal mines. Among the effects on water resources management, mining wastes deposits in the major bed of small rivers becomes a concern since the lack of maintenance of the works leads to difficulties of drainage in period of storm and to situations at risk for the vicinity. A first characterization carried out by the IGRETEC at the request of the Walloon Region leads to the selection of nine spoil heaps for more detailed investigations. The purpose is to update the administrative data by establishing the profile and cross sections of the works, to collect hydrological data and to evaluate measures to be proposed according to the risks and to the dimensioning of the works. The in situ investigations called upon specialized speleologists and the use of video cameras. (authors)

Brooks under colliery heaps in the Walloon Region

International Nuclear Information System (INIS)

Lardinois, J.P.; Flamion, B.; Zech, Y.

2005-01-01

Several studies are presently under progress in the Walloon Region so as to assess the long term environmental impact caused by the closing of coal mines. Among the effects on water resources management, mining wastes deposits in the major bed of small rivers becomes a concern since the lack of maintenance of the works leads to difficulties of drainage in period of storm and to situations at risk for the vicinity. A first characterization carried out by the IGRETEC at the request of the Walloon Region leads to the selection of nine spoil heaps for more detailed investigations. The purpose is to update the administrative data by establishing the profile and cross sections of the works, to collect hydrological data and to evaluate measures to be proposed according to the risks and to the dimensioning of the works. The in situ investigations called upon specialized speleologists and the use of video cameras. (authors)

Chlorination leaching of cadmium

International Nuclear Information System (INIS)

Lach, E.; Pajak, I.; Bojanowska, A.

1978-01-01

The results of the investigations on chlorination leaching of cadmium from dust coming from dry dust collector of sinter belt, that is leaching with water saturated with gaseous chlorine and leaching with solutions of ammonium chloride and sodium chloride were given. The optimum conditions for these processes were established. It was found, that the method of leaching in the presence of gaseous chlorine is more effective, as it allows to report into the solution over 90% cadmium contained in dust. Owing to technical difficulties, environmental protection and safety conditions more advantageous seems to be the use as leaching agent of the ammonium chloride solutions. When applying 20% NH 4 Cl and temperature of 60 0 C, the time of 2 hours and the ratio of solid to liquid of 1:5, 70% cadmium contained in the dust can be reported into the solution. (auth.)

Leaching of Titanium and Silicon from Low-Grade Titanium Slag Using Hydrochloric Acid Leaching

Science.gov (United States)

Zhao, Longsheng; Wang, Lina; Qi, Tao; Chen, Desheng; Zhao, Hongxin; Liu, Yahui; Wang, Weijing

2018-05-01

Acid-leaching behaviors of the titanium slag obtained by selective reduction of vanadium-bearing titanomagnetite concentrates were investigated. It was found that the optimal leaching of titanium and silicon were 0.7% and 1.5%, respectively. The titanium and silicon in the titanium slag were firstly dissolved in the acidic solution to form TiO2+ and silica sol, and then rapidly reprecipitated, forming hydrochloric acid (HCl) leach residue. Most of the silicon presented in the HCl leach residue as floccules-like silica gel, while most of the titanium was distributed in the nano-sized rod-like clusters with crystallite refinement and intracrystalline defects, and, as such, 94.3% of the silicon was leached from the HCl leach residue by alkaline desilication, and 96.5% of the titanium in the titanium-rich material with some rutile structure was then digested by the concentrated sulfuric acid. This provides an alternative route for the comprehensive utilization of titanium and silicon in titanium slag.

Immobilized waste leaching

International Nuclear Information System (INIS)

Suarez, A.A.

1989-01-01

The main mechanism by which the immobilized radioactive materials can return to biosphere is the leaching due to the intrusion of water into the repositories. Some mathematical models and experiments utilized to evaluate the leaching rates in different immobilization matrices are described. (author) [pt

Leaching of gold, silver and accompanying metals from circuit boards (PCBs waste

Directory of Open Access Journals (Sweden)

Jana Ficeriová

2011-12-01

Full Text Available Au-Ag noble metal wastes represent a wide range of waste types and forms, with various accompanying metallic elements.The presented leaching strategy for Au-Ag contained in circuit boards (PCBs aims at gaining gold and silver in the metallic form.Application of the proposed ammonium thiosulphate leaching process for the treatment of the above mentioned Au-Ag containing wastesrepresents a practical, economic and at the same time an ecological solution. The ammonium thiosulphate based leaching of gold and silverfrom PCBs waste, using crushing as a pretreatment, was investigated. It was possible to achieve 98 % gold and 93 % silver recovery within48 hours of ammonium thiosulphate leaching. This type of leaching is a better leaching procedure for recovery of gold and silver from PCBwaste than the classical toxic cyanide leaching. 84 % Cu, 82 % Fe, 77 % Al, 76 % Zn, 70 % Ni, 90 % Pd, 88 % Pb and 83 % Sn recovery ofthe accompanying metals was achieved, using sulphuric acid with hydrogen peroxide, sodium chloride and aqua regia. A four steps leachingprocess gave a very satisfactory yield and a more rapid kinetics for all observed metals solubilization than other technologies.

Study on the leaching behavior of actinides from nuclear fuel debris

Science.gov (United States)

Kirishima, Akira; Hirano, Masahiko; Akiyama, Daisuke; Sasaki, Takayuki; Sato, Nobuaki

2018-04-01

For the prediction of the leaching behavior of actinides contained in the nuclear fuel debris generated by the Fukushima Daiichi nuclear power plant accident in Japan, simulated fuel debris consisting of a UO2-ZrO2 solid solution doped with 137Cs, 237Np, 236Pu, and 241Am tracers was synthesized and investigated. The synthesis of the debris was carried out by heat treatment at 1200 °C at different oxygen partial pressures, and the samples were subsequently used for leaching tests with Milli-Q water and seawater. The results of the leaching tests indicate that the leaching of actinides depends on the redox conditions under which the debris was generated; for example, debris generated under oxidative conditions releases more actinide nuclides to water than that generated under reductive conditions. Furthermore, we found that, as Zr(IV) increasingly substituted U(IV) in the fluorite crystal structure of the debris, the actinide leaching from the debris decreased. In addition, we found that seawater leached more actinides from the debris than pure water, which seems to be caused by the complexation of actinides by carbonate ions in seawater.

Leaching of uranium and thorium from monazite: III. Leaching of radiogenic daughters

International Nuclear Information System (INIS)

Olander, D.; Eyal, Y.

1990-01-01

The solid-state diffusion model of actinide leaching developed in Part II of this series is applied to leaching of radiogenic daughters of the actinide decay chains. For an untreated natural monazite, the direct leaching component of 228 Th release is larger than that for 232 Th because of enhanced solid-state mobility for 228 Th provided by 228 Ra-recoil tracks. A significant portion of the 228 Th which appears in the leachate, however, is attributed to decay of insoluble 228 Ra which is continually released from the mineral by matrix dissolution and recoil ejection. For a monazite sample that was annealed at 800 degree C prior to leaching, the bulk of the 228 Th in solution was supplied by decay of 228 Ra rejected from the mineral matrix during annealing. The radiogenic 234 U daughter of the 238 U decay chain did not exhibit similarly enhanced leaching because the long half-life of 234 U permitted local radiation damage to be annealed out at ambient temperature prior to 234 U decay

Dynamic leaching behavior of geogenic As in soils after cement-based stabilization/solidification.

Science.gov (United States)

Li, Jiang-Shan; Wang, Lei; Tsang, Daniel C W; Beiyuan, Jingzi; Poon, Chi Sun

2017-12-01

Cement-based stabilization/solidification (S/S) is a practical treatment approach for hazardous waste with anthropogenic As sources; however, its applicability for geogenic As-containing soil and the long-term leaching potential remain uncertain. In this study, semi-dynamic leaching test was performed to investigate the influence of S/S binders (cement blended with fuel ash (FA), furnace bottom ash (FBA), or ground granulated blast furnace slag (GGBS)) on the long-term leaching characteristics of geogenic As. The results showed that mineral admixtures with higher Ca content and pozzolanic activity were more effective in reducing the leached As concentrations. Thus, cement blended with FBA was inferior to other binders in suppressing the As leaching, while 20% replacement of ordinary Portland cement by GGBS was considered most feasible for the S/S treatment of As-containing soils. The leachability of geogenic As was suppressed by the encapsulation effect of solidified matrix and interlocking network of hydration products that were supported by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) results. The long-term leaching of geogenic As from the monolithic samples was diffusion-controlled. Increasing the Ca content in the samples led to a decrease in diffusion coefficient and an increase in feasibility for "controlled utilization" of the S/S-treated soils.

Using microbiological leaching method to remove heavy metals from sludge

Directory of Open Access Journals (Sweden)

Zhuyu Gu

2017-01-01

Full Text Available Microbial leaching is one of the most effective methods to remove heavy metals from sludge. In the conducted researches, the sludge samples were processed with Thiobacillus ferrooxidans and Thiobacillus thiooxidans obtained via cultivation, extraction and purification processes. Heavy metals such as Pb, Cd, Cu and Ni were leached from sludge by Thiobacillus ferrooxidans and Thiobacillus thiooxidans within different substrate concentration and pH value conditions. It is defined that from the point of view of economy and efficiency the optimal concentration of FeSO4.7H2O and sulfur for bio-leaching process was 0.2 g. The leaching rates of heavy metals such as Pb, Cd, Cu and Ni of the same concentration were 74.72%, 81.54%, 70.46% and 77.35% respectively. However, no significant differences depending on the pH value among the leaching rates were defined, even for the pH value of 1.5. Along with the removal of heavy metals from sludge, the organic matter, N, P, K were also leached to some extent. The losing rate of phosphorus was the highest and reached 38.44%. However, the content of organic matter, N, P, K in the processed sludge were higher in comparison with level I of the National Soil Quality Standards of China. Ecological risk of heavy metals in sludge before and after leaching was assessed by Index of Geo-accumulation (Igeo and comprehensive potential risk (RI. The results of research defined that the content of heavy metals in sludge meets the level of low ecological risk after leaching and their contents is lower in comparison with the National Agricultural Sludge Standard of China. Sludge leached by biological methods is possible to use for treatment for increasing soil fertility.

Nitrate Leaching Management

Science.gov (United States)

Nitrate (NO3) leaching is a significant nitrogen (N) loss process for agriculture that must be managed to minimize NO3 enrichment of groundwater and surface waters. Managing NO3 leaching should involve the application of basic principles of understanding the site’s hydrologic cycle, avoiding excess ...

Nitrate leaching index

Science.gov (United States)

The Nitrate Leaching Index is a rapid assessment tool that evaluates nitrate (NO3) leaching potential based on basic soil and climate information. It is the basis for many nutrient management planning efforts, but it has considerable limitations because of : 1) an oversimplification of the processes...

Lysimeter study to investigate the effect of rainfall patterns on leaching of isoproturon.

Science.gov (United States)

Beulke, Sabine; Brown, Colin D; Fryer, Christopher J; Walker, Allan

2002-01-01

The influence of five rainfall treatments on water and solute leaching through two contrasting soil types was investigated. Undisturbed lysimeters (diameter 0.25 m, length 0.5 m) from a sandy loam (Wick series) and a moderately structured clay loam (Hodnet series) received autumn applications of the radio-labelled pesticide isoproturon and bromide tracer. Target rainfall plus irrigation from the end of November 1997 to May 1998 ranged from drier to wetter than average (235 to 414 mm); monthly rainfall was varied according to a pre-selected pattern or kept constant (triplicate lysimeters per regime). Leachate was collected at intervals and concentrations of the solutes were determined. Total flow (0.27-0.94 pore volumes) and losses of bromide (3-80% of applied) increased with increasing inputs of water and were larger from the Wick sandy loam than from the Hodnet clay loam soil. Matrix flow appeared to be the main mechanism for transport of isoproturon through the Wick soil whereas there was a greater influence of preferential flow for the Hodnet lysimeters. The total leached load of isoproturon from the Wick lysimeters was 0.02-0.26% of that applied. There was no clear variation in transport processes between the rainfall treatments investigated for this soil and there was an approximately linear relationship (r2 = 0.81) between leached load and total flow. Losses of isoproturon from the Hodnet soil were 0.03-0.39% of applied and there was evidence of enhanced preferential flow in the driest and wettest treatments. Leaching of isoproturon was best described by an exponential relationship between load and total flow (r2 = 0.62). A 45% increase in flow between the two wettest treatments gave a 100% increase in leaching of isoproturon from the Wick soil. For the Hodnet lysimeters, a 35% increase in flow between the same treatments increased herbicide loss by 325%.

Leaching characteristics of Wadi Belih uraniferous Hammamat sediments,eastern desert,Egypt

International Nuclear Information System (INIS)

Mahdy, M.A.; EL-Hazek, M.N.

1998-01-01

This work deals with the direct chemical treatment of Wadi Belih uraniferous ore material using the agitation leaching technique. The study ore is mainly localized in siltstones belonging to the Hammamat sediments situated in the northern part of the eastern desert. The uranium mineral in the ore are mainly represented by the silicate mineral uranophane, the vanadate mineral tyuyamunite and to a laser extent the sulphate mineral shroekingerite, both acid (sulphuric acid) alkaline (sodium carbonate and bicarbonate) leaching methods have been applied beside sodium and ferric chlorides. The latter leaching reagents are greatly beneficial in removing radium together with uranium, a matter which is greatly important for environmental concerns

Human error analysis project (HEAP) - The fourth pilot study: verbal data for analysis of operator performance

International Nuclear Information System (INIS)

Braarud, Per Oeyvind; Droeyvoldsmo, Asgeir; Hollnagel, Erik

1997-06-01

This report is the second report from the Pilot study No. 4 within the Human Error Analyses Project (HEAP). The overall objective of HEAP is to provide a better understanding and explicit modelling of how and why ''cognitive errors'' occur. This study investigated the contribution from different verbal data sources for analysis of control room operator's performance. Operator's concurrent verbal report, retrospective verbal report, and process expert's comments were compared for their contribution to an operator performance measure. This study looked into verbal protocols for single operator and for team. The main findings of the study were that all the three verbal data sources could be used to study performance. There was a relative high overlap between the data sources, but also a unique contribution from each source. There was a common pattern in the types of operator activities the data sources gave information about. The operator's concurrent protocol overall contained slightly more information on the operator's activities than the other two verbal sources. The study also showed that concurrent verbal protocol is feasible and useful for analysis of team's activities during a scenario. (author)

The impact of new technology on the economics of uranium production from low-grade ores

International Nuclear Information System (INIS)

Simonsen, H.A.; Boydell, D.W.; James, H.E.

1981-01-01

The subject is discussed under the following headings: influence of a depressed market on uranium supply from low-grade ores; potential areas for a reduction in uranium ore processing costs; in-situ leaching (solution mining; heap leaching; resin-in-pulp; solvent-in-pulp; belt filtration; continuous ion exchange; solvent extraction); preconcentration (upgrading of coarse rock; upgrading in the mill; wet high-intensity magnetic separation; flotation); summary and conclusions. (U.K.)

Leaching Behavior of Heavy Metals from Cement Pastes Using a Modified Toxicity Characteristic Leaching Procedure (TCLP).

Science.gov (United States)

Huang, Minrui; Feng, Huajun; Shen, Dongsheng; Li, Na; Chen, Yingqiang; Shentu, Jiali

2016-03-01

As the standard toxicity characteristic leaching procedure (TCLP) can not exhaust the acid neutralizing capacity of the cement rotary kiln co-processing solid wastes products which is particularly important for the assessment of the leaching concentrations of heavy metals. A modified TCLP was proposed. The extent of leaching of heavy metals is low using the TCLP and the leaching performance of the different metals can not be differentiated. Using the modified TCLP, however, Zn leaching was negligible during the first 180 h and then sharply increased (2.86 ± 0.18 to 3.54 ± 0.26 mg/L) as the acidity increased (pH leaching is enhanced using the modified TCLP. While Pb leached readily during the first 126 h and then leachate concentrations decreased to below the analytical detection limit. To conclude, this modified TCLP is a more suitable method for these cement rotary kiln co-processing products.

The geography, geology and mining history of Rum Jungle

International Nuclear Information System (INIS)

Lowson, R.T.

1975-01-01

The geology and geography of the Rum Jungle region are described. A description is given of the effect on the environment of mining operations such as ore processing, effluent disposal and the leaching of stockpiles and overburden heaps. (author)

Thermal treatment and leaching of biochar alleviates plant growth inhibition from mobile organic compounds

Directory of Open Access Journals (Sweden)

Nigel V. Gale

2016-08-01

Full Text Available Recent meta-analyses of plant responses to biochar boast positive average effects of between 10 and 40%. Plant responses, however, vary greatly across systems, and null or negative biochar effects are increasingly reported. The mechanisms responsible for such responses remain unclear. In a glasshouse experiment we tested the effects of three forestry residue wood biochars, applied at five dosages (0, 5, 10, 20, and 50 t/ha to a temperate forest drystic cambisol as direct surface applications and as complete soil mixes on the herbaceous pioneers Lolium multiflorum and Trifolium repens. Null and negative effects of biochar on growth were found in most cases. One potential cause for null and negative plant responses to biochar is plant exposure to mobile compounds produced during pyrolysis that leach or evolve following additions of biochars to soil. In a second glasshouse experiment we examined the effects of simple leaching and heating techniques to ameliorate potentially phytotoxic effects of volatile and leachable compounds released from biochar. We used Solid Phase Microextraction (SPME–gas chromatography–mass spectrometry (GC-MS to qualitatively describe organic compounds in both biochar (through headspace extraction, and in the water leachates (through direct injection. Convection heating and water leaching of biochar prior to application alleviated growth inhibition. Additionally, growth was inhibited when filtrate from water-leached biochar was applied following germination. SPME-GC-MS detected primarily short-chained carboxylic acids and phenolics in both the leachates and solid chars, with relatively high concentrations of several known phytotoxic compounds including acetic acid, butyric acid, 2,4-di-tert-butylphenol and benzoic acid. We speculate that variable plant responses to phytotoxic organic compounds leached from biochars may largely explain negative plant growth responses and also account for strongly species

Vat leaching of gold ores and utilization of the tailings; Kinkoseki no vat leaching to koshi no yuko riyo

Energy Technology Data Exchange (ETDEWEB)

Hosooka, T. [Nippon Clay Mining Co. Ltd., Tokyo (Japan); Miyagawa, H. [Mitsui Mining and Smelting Co. Ltd., Tokyo (Japan)

1996-01-25

Mitsui Kushikino Mine previously processed two gold ores from Kushikino and Iwato ore deposits by the all slime cyanidation method, where the ores were ground to fine size smaller than 75 {mu}m and leached with sodium, cyanide. A large amount of slimes were produced as waste and discarded in tailings ponds. To save the costs of grinding and waste treatment it is desirable to process coarse sized ores. The Iwato ore is gold and silver bearing silicified porous rock. As most gold and silver in the Iwato ore are concentrated in the pores, leaching of coarse sized ore is expected to be possible. Laboratory tests and pilot plant tests of vat leaching for the Iwato ore were carried out using 0.15-8.0 mm feed. These results showed that the gold dissolution rate was similar to that by the all slime cyanidation and the decrease in gold recovery was a few %. The properties of these tailings can be used in fine aggregate of concrete. Based on the results vat leaching of the Iwato ore was adopted in the plant. The tailings are sold and used as fine aggregate. Utilization of slime tailings from the other ores was also developed and they are used as flux in copper smelters. Now, there is no tailings pond at Mitsui Kushikino Mine. 9 refs., 10 figs., 5 tabs.

A New Generation of Leaching Tests – The Leaching Environmental Assessment Framework

Science.gov (United States)

Provides an overview of newly released leaching tests that provide a more accurate source term when estimating environmental release of metals and other constituents of potential concern (COPCs). The Leaching Environmental Assessment Framework (LEAF) methods have been (1) develo...

The leaching characteristics of vitrified slag

International Nuclear Information System (INIS)

Zhang, Jinlong; Li, Yaojian; Tian, Junguo; Sheng, Hongzhi; Xu, Yongxiang

2010-01-01

Full Text: Plasma-arc technology was developed to fix the heavy metal of flying ash by the Institute of Mechanics, Chinese Academy of Sciences (CAS-IMECH). A direct current (DC) experimental facility of 30 kW with plasma-arc technology was setup to form vitrified slag. The additives (CaO, SiO 2 ) were added into the reactor to form vitrified slag and fix the heavy metal (Cr, Pb), under dissimilar condition (long and short heating-up time, natural and water cooling). Vitrified slag was broken into different particle size, from 0.1 mm to 1 cm. The particles with different specific surface area were used to study the leaching of heavy metals in vitrified slag rate of speed. The pH value of leaching solution are from 2 to 12, the experiment was kept at different external temperature, from 4 degree Celsius to 70 degree celsius, for 1 week to 1 month. Heavy metal leaching concentration was used to measure the chemical stability of vitrified slag. The results show that the higher specific surface area, the higher heavy metal leaching concentration, but when the specific surface area reaches a certain value, little change in leaching concentration. The impact of temperature on leaching concentration was not significant, from 4 degree Celsius to 70 degree Celsius. The leaching concentration increases with decreasing of the pH value of leaching solution when the pH value of leaching solution less than 7, and little change in concentration increases with pH value when the pH value of leaching solution more than 7. Compared with the leaching concentration after 1 month, the leaching concentration after 1 week has not changed significantly. (Author)

Defining Effective Salt Leaching Regions Between Drains

OpenAIRE

ANAPALI, Ömer; ŞAHİN, Üstün; ÖZTAŞ, Taşkın; HANAY, Abdurrahman

2014-01-01

The application of sufficient amounts of leaching water by means of an effective method is very important in the management and reclamation of saline and sodic soils. Reclamation cannot be achieved with insufficient leaching water application, while excess water application may cause severe problems in soil. Knowledge of the leaching regions and intensities may help to control the amounts of leaching water through effective leaching methods in areas of limited leaching. This study was und...

Leaching From Biomass Gasification Residues

DEFF Research Database (Denmark)

Allegrini, Elisa; Boldrin, Alessio; Polletini, A.

2011-01-01

The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled with geoche......The aim of the present work is to attain an overall characterization of solid residues from biomass gasification. Besides the determination of chemical and physical properties, the work was focused on the study of leaching behaviour. Compliance and pH-dependence leaching tests coupled...

76 FR 60941 - Policy Regarding Submittal of Amendments for Processing of Equivalent Feed at Licensed Uranium...

Science.gov (United States)

2011-09-30

... Processing of Equivalent Feed at Licensed Uranium Recovery Facilities AGENCY: Nuclear Regulatory Commission... State-licensed uranium recovery site, either conventional, heap leach, or in situ recovery. DATES... Regarding Submittal of Amendments for Processing of Equivalent Feed at Licensed Uranium Recovery Facilities...

Ghana Mining Journal - Vol 14 (2013)

African Journals Online (AJOL)

Understanding Lateritic Ore Agglomeration Behaviour as a Precursor to Enhanced Heap Leaching · EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT. J Addai-Mensah, I Quaicoe, A Nosrati, DJ Robinson, 41-50 ...

Measurement of leach rates: a review

International Nuclear Information System (INIS)

Mendel, J.E.

1982-01-01

A historical perspective of the techniques that can be used to measure the leach rate of radioactive waste forms is presented. The achievement of leach rates that are as low as possible has been an important goal ever since the development of solidification processes for liquid radioactive wastes began in the 1950's. Leach tests can be divided into two major categories, dynamic and static, based on whether or not the leachant in contact with the test specimen is changed during the course of the test. Both types of tests have been used extensively. The results of leach tests can be used to compare waste forms, and that has been a major purpose of leach data heretofore; increasingly, however, the data now are needed for predicting long-term leaching behavior during geologic disposal. This requirement is introducing new complexities into leach testing methodology. 3 figures, 2 tables

Radioactivity measurements in the vicinity of the mine waste heap at Crossen and radiation dose assessment; Radioaktivitaetsmessungen in der Umgebung der Bergehalde Crossen und Abschaetzung der Strahlenexposition

Energy Technology Data Exchange (ETDEWEB)

Kulzer, R.

1998-09-01

The radiation dose to the population living in the vicinity of the mine waste heap is assessed. The measurements carried out were to verify the dose relevance of ambient radioactivity on site, in particular the ingestion and inhalation pathways and the external exposure pathways. The nuclide Pb-210 was used as an indicator because of its large dose factor for assessment of ingestion and its airborne dispersion as an Rn-222 daughter product. The waste heap material releases large quantities of this nuclide. Ingestion of radioactivity from the waste heap may be caused by wind-borne erosion and activity deposition on plants in the area. Thererfore, the specific activities of Pb-210 and Ra-226 have been measured in soil and plant specimens sampled at various distances from the waste heap. (orig./CB) [Deutsch] Die Strahlenexposition der in der Naehe einer Bergehalde lebenden Bevoelkerung wird bestimmt. Zu diesem Zweck wurden Messungen realisiert, die den Ingestions- und Inhalationspfad sowie die externe Exposition fuer die vorgefundene Situation auf ihre Dosisrelevanz ueberpruefen sollten. Hierzu diente das Nuklid Pb-210 mit seinem grossen Dosisfaktor fuer die Ingestion und seiner besonderen Verbreitungsmoeglichkeit ueber die Luft als Tochter von Rn-222. Dieses wird aus dem Haldenmaterial in grossen Mengen freigesetzt. Haldenmaterial kann ueber den Ingestionspfad in den menschlichen Koerper aufgenommen werden, wenn es durch Winderosion auf Pflanzenoberflaechen in der Umgebung abgelagert wird.Deshalb wurden die spezifischen Aktivitaeten an Pb-210 und Ra-226 von Boden- und Pflanzenproben in verschiedenen Entfernungen zur Halde bestimmt.

LCA of management strategies for RDF incineration and gasification bottom ash based on experimental leaching data

DEFF Research Database (Denmark)

Gianfilippo, Martina Di; Costa, Giulia; Pantini, Sara

2016-01-01

data were used to estimate the potential release from each of the two types of residues. Specific attention was placed on the sensitivity of leaching properties and the determination of emissions by leaching, including: leaching data selection, material properties and assumptions related to emission......The main characteristics and environmental properties of the bottom ash (BA) generated from thermal treatment of waste may vary significantly depending on the type of waste and thermal technology employed. Thus, to ensure that the strategies selected for the management of these residues do...... not cause adverse environmental impacts, the specific properties of BA, in particular its leaching behavior, should be taken into account. This study focuses on the evaluation of potential environmental impacts associated with two different management options for BA from thermal treatment of Refuse Derived...

Effects of grazing strategy on limiting nitrate leaching in grazed grass-clover pastures on coarse sandy soil

DEFF Research Database (Denmark)

Hansen, Elly Møller; Eriksen, Jørgen; Søegaard, Karen

2012-01-01

-term mean. The experiment was initiated in a 4-yr-old grass-clover sward in south Denmark. Three treatments were as follows grazing only (G), spring cut followed by grazing (CG) and both spring and autumn cuts with summer grazing (CGC). Nitrate leaching was calculated by extracting water isolates from 80 cm......Urinations of ruminants on grazed pastures increase the risk of nitrate leaching. The study investigated the effect of reducing the length of the grazing season on nitrate leaching from a coarse sandy, irrigated soil during 2006–2007 and 2007–2008. In both years, precipitation was above the long...... depth using ceramic suction cups. Because of considerable variation in measured nitrate concentrations, the 32 installed suction cups per treatment were insufficient to reveal differences between treatments. However, weighted nitrate leaching estimations for G, CG and CGC showed estimated mean nitrate N...

Leaching behavior of some radionuclides from cement matrix incorporating exhausted polymeric resins

International Nuclear Information System (INIS)

Abou-Mesalam, M.M.

2002-01-01

Exhausted poly(acrylamide-acrylic acid) impregnated with zirconium phosphate {P(AM-AA)-ZrP} produced from the treatment process of radioactive liquid waste was incorporated in different types of cement to prevent widespreading of radionuclides into the human environment. The rates at which 60 Co, 65 Zn and 152,154 Eu are leached from Ordinary Portland Cement (OPC) and Blast Furnace Slag Cement (BFSC) were measured. From the leaching data the leach coefficients of 60 Co, 65 Zn and 152,154 Eu were determined and were found to vary between 1.62 x 10 -8 to 7.06 x 10 -10 cm 2 /day and 1.01 x 10 -8 to 8.93 x 10 -9 cm 2 /day in OPC and BFSC, respectively. In general, the radionuclide leaching rates followed the order: 152,154 Eu > 65 Zn > 60 Co. The leach coefficient was found to be dependent on the composition of the leachants and varied in the order: distilled water > ground water > synthetic sea water. The effect of NaNo 3 concentration in the wastes on the leach coefficient of 60 Co from OPC was also studied. (author)

Fe, Cr, Ni, Cu, Mg, Al, Ti, and S contents in plants and soil of heaps of nickel smelting works

Energy Technology Data Exchange (ETDEWEB)

Banasova, V; Hajduk, J

1977-01-01

The writers established the Fe, Ce, Cr, Ni, Ca, Mg, Al, Ti and S contents in the neopedon of heaps piling up from processing of nickel ore as well as in the plants: Cardaria draba, Salsola cali, Agropyrum repens, Bromus erectus, Calamagrostis epigeios, Cynodon dactylon and Matricaria inodora, growing on such heaps. Ca, Mg and S contents were found to be higher in dicotyledons and Fe, Al, Ti, Ni and Cr contents higher in monocotyledons. The analyzed dicotyledons appeared to be concentrators of Ca and S. Highest Fe, Al, Ti, Ni and Cr contents were found in individuals of the species Agropyrum repens. The neopedon as well as the plants had extraordinarily high Cr concentrations. The species Salsola cali has been found to possess an unusually higher affinity to the dump substrate after processing of nickel ore and to be a concentrator of Mg. 16 references, 1 table.

Cross-current leaching of indium from end-of-life LCD panels.

Science.gov (United States)

Rocchetti, Laura; Amato, Alessia; Fonti, Viviana; Ubaldini, Stefano; De Michelis, Ida; Kopacek, Bernd; Vegliò, Francesco; Beolchini, Francesca

2015-08-01

Indium is a critical element mainly produced as a by-product of zinc mining, and it is largely used in the production process of liquid crystal display (LCD) panels. End-of-life LCDs represent a possible source of indium in the field of urban mining. In the present paper, we apply, for the first time, cross-current leaching to mobilize indium from end-of-life LCD panels. We carried out a series of treatments to leach indium. The best leaching conditions for indium were 2M sulfuric acid at 80°C for 10min, which allowed us to completely mobilize indium. Taking into account the low content of indium in end-of-life LCDs, of about 100ppm, a single step of leaching is not cost-effective. We tested 6 steps of cross-current leaching: in the first step indium leaching was complete, whereas in the second step it was in the range of 85-90%, and with 6 steps it was about 50-55%. Indium concentration in the leachate was about 35mg/L after the first step of leaching, almost 2-fold at the second step and about 3-fold at the fifth step. Then, we hypothesized to scale up the process of cross-current leaching up to 10 steps, followed by cementation with zinc to recover indium. In this simulation, the process of indium recovery was advantageous from an economic and environmental point of view. Indeed, cross-current leaching allowed to concentrate indium, save reagents, and reduce the emission of CO2 (with 10 steps we assessed that the emission of about 90kg CO2-Eq. could be avoided) thanks to the recovery of indium. This new strategy represents a useful approach for secondary production of indium from waste LCD panels. Copyright © 2015 Elsevier Ltd. All rights reserved.

Leaching behavior of harmful components from cement solidities of fluidized-bed coal ash

Energy Technology Data Exchange (ETDEWEB)

Baba, T.; Fukuoka, H.; Shigemoto, N. [Fuji Clean Co., Kagawa (Japan)

2008-07-15

Solidifies of fluidized-bed fly ash with slag cement were prepared by hydrothermal treatment after adding gypsum, Na3PO{sub 4}, or Al2(SO{sub 4}){sub 3}. XRD analysis of the solidifies was performed and leaching behavior of Pb and F from the solidities was investigated. The fly ash-cement and fly ash-cement-gypsum solidifies showed rather high leaching concentration of F and Pb. The F leaching was explained by solubility products of a Ca(OH){sub 2} CaF2 system. The Pb leaching concentrations roughly agreed with the theoretical curve for hydroxo complexes of Pb, showing a strong dependence on pH. Addition of Na3PO{sub 4} and Al2(SO{sub 4}){sub 3}, to cement solidities gave katoite and aluminium phosphate, and ettringite, respectively, and these solidities showed lower leaching concentrations of F and Pb than the fly ash-cement and fly ash-cement-gypsum solidifies. Capture of F and Pb in crystalline components such as ettringite probably accounts for such leaching suppression.

Pesticide leaching through sandy and loamy fields - long-term lessons learnt from the Danish Pesticide Leaching Assessment Programme.

Science.gov (United States)

Rosenbom, Annette E; Olsen, Preben; Plauborg, Finn; Grant, Ruth; Juhler, René K; Brüsch, Walter; Kjær, Jeanne

2015-06-01

The European Union authorization procedure for pesticides includes an assessment of the leaching risk posed by pesticides and their degradation products (DP) with the aim of avoiding any unacceptable influence on groundwater. Twelve-year's results of the Danish Pesticide Leaching Assessment Programme reveal shortcomings to the procedure by having assessed leaching into groundwater of 43 pesticides applied in accordance with current regulations on agricultural fields, and 47 of their DP. Three types of leaching scenario were not fully captured by the procedure: long-term leaching of DP of pesticides applied on potato crops cultivated in sand, leaching of strongly sorbing pesticides after autumn application on loam, and leaching of various pesticides and their DP following early summer application on loam. Rapid preferential transport that bypasses the retardation of the plow layer primarily in autumn, but also during early summer, seems to dominate leaching in a number of those scenarios. Copyright © 2015 Elsevier Ltd. All rights reserved.

Leaching and geochemical behavior of fired bricks containing coal wastes.

Science.gov (United States)

Taha, Yassine; Benzaazoua, Mostafa; Edahbi, Mohamed; Mansori, Mohammed; Hakkou, Rachid

2018-03-01

High amounts of mine wastes are continuously produced by the mining industry all over the world. Recycling possibility of some wastes in fired brick making has been investigated and showed promising results. However, little attention is given to the leaching behavior of mine wastes based fired bricks. The objective of this paper is to evaluate the geochemical behavior of fired bricks containing different types of coal wastes. The leachates were analyzed for their concentration of As, Ba, Cd, Co, Cr, Cu, Mo, Ni, Pb, Zn and sulfates using different leaching tests; namely Tank Leaching tests (NEN 7375), Toxicity Characteristic Leaching Procedure (TCLP) and pH dependence test (EPA, 1313). The results showed that the release of constituents of potential interest was highly reduced after thermal treatment and were immobilized within the glassy matrix of the fired bricks. Moreover, it was also highlighted that the final pH of all fired samples changed and stabilized around 8-8.5 when the initial pH of leaching solution was in the range 2.5-11.5. The release of heavy metals and metalloids (As) tended to decrease with the increase of pH from acidic to alkaline solutions while Mo displayed a different trend. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycling process for recovery of gallium from GaN an e-waste of LED industry through ball milling, annealing and leaching.

Science.gov (United States)

Swain, Basudev; Mishra, Chinmayee; Kang, Leeseung; Park, Kyung-Soo; Lee, Chan Gi; Hong, Hyun Seon

2015-04-01

Waste dust generated during manufacturing of LED contains significant amounts of gallium and indium, needs suitable treatment and can be an important resource for recovery. The LED industry waste dust contains primarily gallium as GaN. Leaching followed by purification technology is the green and clean technology. To develop treatment and recycling technology of these GaN bearing e-waste, leaching is the primary stage. In our current investigation possible process for treatment and quantitative leaching of gallium and indium from the GaN bearing e-waste or waste of LED industry dust has been developed. To recycle the waste and quantitative leaching of gallium, two different process flow sheets have been proposed. In one, process first the GaN of the waste the LED industry dust was leached at the optimum condition. Subsequently, the leach residue was mixed with Na2CO3, ball milled followed by annealing, again leached to recover gallium. In the second process, the waste LED industry dust was mixed with Na2CO3, after ball milling and annealing, followed acidic leaching. Without pretreatment, the gallium leaching was only 4.91 w/w % using 4M HCl, 100°C and pulp density of 20g/L. After mechano-chemical processing, both these processes achieved 73.68 w/w % of gallium leaching at their optimum condition. The developed process can treat and recycle any e-waste containing GaN through ball milling, annealing and leaching. Copyright © 2015 Elsevier Inc. All rights reserved.

The Danish Pesticide Leaching Assessment Programme

DEFF Research Database (Denmark)

Rosenbom, Annette Elisabeth; Brüsch, Walter Michael; Juhler, Rene K.

In 1998, the Danish Parliament initiated the Pesticide Leaching Assessment Programme (PLAP), an intensive monitoring programme aimed at evaluating the leaching risk of pesticides under field conditions. The objective of the PLAP is to improve the scientific foundation for decision......-making in the Danish regulation of pesticides. The specific aim is to analyse whether pesticides applied in accordance with current regulations leach to groundwater in unacceptable concentrations. The programme currently evaluates the leaching risk of 41 pesticides and 40 degradation products at five agricultural......, thiamethoxam, tribenuronmethyl, and triasulfuron) did not leach during the 1999-2009 monitoring period. 13 of the applied pesticides exhibited pronounced leaching of the pesticide and/or their degradation product(-s) 1 m b.g.s. in yearly average concentrations exceeding 0.1 μg/l (maximum allowable...

Leaching characteristics of copper flotation waste before and after vitrification.

Science.gov (United States)

Coruh, Semra; Ergun, Osman Nuri

2006-12-01

Copper flotation waste from copper production using a pyrometallurgical process contains toxic metals such as Cu, Zn, Co and Pb. Because of the presence of trace amounts of these highly toxic metals, copper flotation waste contributes to environmental pollution. In this study, the leaching characteristics of copper flotation waste from the Black Sea Copper Works in Samsun, Turkey have been investigated before and after vitrification. Samples obtained from the factory were subjected to toxicity tests such as the extraction procedure toxicity test (EP Tox), the toxicity characteristic leaching procedure (TCLP) and the "method A" extraction procedure of the American Society of Testing and Materials. The leaching tests showed that the content of some elements in the waste before vitrification exceed the regulatory limits and cannot be disposed of in the present form. Therefore, a stabilization or inertization treatment is necessary prior to disposal. Vitrification was found to stabilize heavy metals in the copper flotation waste successfully and leaching of these metals was largely reduced. Therefore, vitrification can be an acceptable method for disposal of copper flotation waste.

Leaching characteristics of the metal waste form from the electrometallurgical treatment process: Product consistency testing

International Nuclear Information System (INIS)

Johnson, S. G.; Keiser, D. D.; Frank, S. M.; DiSanto, T.; Noy, M.

1999-01-01

Argonne National Laboratory is developing an electrometallurgical treatment for spent fuel from the experimental breeder reactor II. A product of this treatment process is a metal waste form that incorporates the stainless steel cladding hulls, zirconium from the fuel and the fission products that are noble to the process, i.e., Tc, Ru, Nb, Pd, Rh, Ag. The nominal composition of this waste form is stainless steel/15 wt% zirconium/1--4 wt% noble metal fission products/1--2 wt % U. Leaching results are presented from several tests and sample types: (1) 2 week monolithic immersion tests on actual metal waste forms produced from irradiated cladding hulls, (2) long term (>2 years) pulsed flow tests on samples containing technetium and uranium and (3) crushed sample immersion tests on cold simulated metal waste form samples. The test results will be compared and their relevance for waste form product consistency testing discussed

DESIGN AND ANALYSIS OF AN EXPERIMENT FOR ASSESSING CYANIDE IN GOLD MINING WASTES

Science.gov (United States)

Gold mining wastes treated by heap leaching cyanidization typically contain several metallo-cyanide species. Accurate measurement of total cyanide by the most common methods in such a case may be hampered by the inadequate recoveries that occur for certain cyanide compounds (e.g....

Monitoring of a burning conical heap by combining topographical mapping with infrared thermography

International Nuclear Information System (INIS)

Carpentier, O.; Antczak, E.; Defer, D.; Duthoit, B.

2003-01-01

One of the most used method for monitoring a slag heap is the air infrared thermography. Even if it permit to survey a large area and provide a well contrasted display of dangerous areas, this method is expensive, perturbed by atmospheric conditions and cannot offer an accurate localization of defects. In order to mitigate this disadvantage, the LAMH, in association with Groupe Charbonnages de France, set up a method based on topographic and infrared thermographic cross reading which is more accurate, less expensive and, in a near future, will permit a monitoring of combustion reaction. (authors)

Recycling process for recovery of gallium from GaN an e-waste of LED industry through ball milling, annealing and leaching

Energy Technology Data Exchange (ETDEWEB)

Swain, Basudev, E-mail: swain@iae.re.kr; Mishra, Chinmayee; Kang, Leeseung; Park, Kyung-Soo, E-mail: kspark@iae.re.kr; Lee, Chan Gi; Hong, Hyun Seon, E-mail: hshong@iae.re.kr

2015-04-15

Waste dust generated during manufacturing of LED contains significant amounts of gallium and indium, needs suitable treatment and can be an important resource for recovery. The LED industry waste dust contains primarily gallium as GaN. Leaching followed by purification technology is the green and clean technology. To develop treatment and recycling technology of these GaN bearing e-waste, leaching is the primary stage. In our current investigation possible process for treatment and quantitative leaching of gallium and indium from the GaN bearing e-waste or waste of LED industry dust has been developed. To recycle the waste and quantitative leaching of gallium, two different process flow sheets have been proposed. In one, process first the GaN of the waste the LED industry dust was leached at the optimum condition. Subsequently, the leach residue was mixed with Na{sub 2}CO{sub 3}, ball milled followed by annealing, again leached to recover gallium. In the second process, the waste LED industry dust was mixed with Na{sub 2}CO{sub 3}, after ball milling and annealing, followed acidic leaching. Without pretreatment, the gallium leaching was only 4.91 w/w % using 4 M HCl, 100 °C and pulp density of 20 g/L. After mechano-chemical processing, both these processes achieved 73.68 w/w % of gallium leaching at their optimum condition. The developed process can treat and recycle any e-waste containing GaN through ball milling, annealing and leaching. - Highlights: • Simplest process for treatment of GaN an LED industry waste developed. • The process developed recovers gallium from waste LED waste dust. • Thermal analysis and phase properties of GaN to Ga{sub 2}O{sub 3} and GaN to NaGaO{sub 2} revealed. • Solid-state chemistry involved in this process reported. • Quantitative leaching of the GaN was achieved.

Reduction of inorganics from macroalgae Laminaria digitata and spent mushroom compost (SMC) by acid leaching and selective hydrothermal liquefaction

DEFF Research Database (Denmark)

Toor, Saqib Sohail; Jasiunas, Lukas; Xu, Chunbao (Charles)

2018-01-01

Hydrothermal liquefaction (HTL) is a promising route for producing bio-crude from various biomass feedstocks. However, high content of inorganic constituents in biomass like macroalgae Laminaria digitata and spent mushroom compost (SMC) affect the conversion process and the resulting fuel products....... This research studied the effects of different acid leaching treatments on such feedstocks, subsequent HTL, and bio-crude properties. Leaching treatments were performed using five different agents: deionized water, acetic acid, citric acid, sulfuric acid, and hydrochloric acid. Performance of leaching...... was evaluated by analyzing both leached biomass and HTL products by elemental analysis, ash content, inductively coupled plasma (ICP) analysis, and X-ray diffraction (XRD) analysis. Catalytic and non-catalytic HTL of both feedstocks before and after treatment were performed in a 10-mL microreactor at 400 °C...

Reduction of metal leaching in brown coal fly ash using geopolymers

International Nuclear Information System (INIS)

Bankowski, P.; Zou, L.; Hodges, R.

2004-01-01

Current regulations classify fly ash as a prescribed waste and prohibit its disposal in regular landfill. Treatment of the fly ash can reduce the leach rate of metals, and allow it to be disposed in less prescribed landfill. A geopolymer matrix was investigated as a potential stabilisation method for brown coal fly ash. Precipitator fly ash was obtained from electrostatic precipitators and leached fly ash was collected from ash disposal ponds, and leaching tests were conducted on both types of geopolymer stabilised fly ashes. The ratio of fly ash to geopolymer was varied to determine the effects of different compositions on leaching rates. Fourteen metals and heavy metals were targeted during the leaching tests and the results indicate that a geopolymer is effective at reducing the leach rates of many metals from the fly ash, such as calcium, arsenic, selenium, strontium and barium. The major element leachate concentrations obtained from leached fly ash were in general lower than that of precipitator fly ash. Conversely, heavy metal leachate concentrations were lower in precipitator fly ash than leached pond fly ash. The maximum addition of fly ash to this geopolymer was found to be 60 wt% for fly ash obtained from the electrostatic precipitators and 70 wt% for fly ash obtained from ash disposal ponds. The formation of geopolymer in the presence of fly ash was studied using 29Si MAS-NMR and showed that a geopolymer matrix was formed. X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) imaging showed the interaction of the fly ash with the geopolymer, which was related to the leachate data and also the maximum percentage fly ash addition

Weatherability and Leach Resistance of Wood Impregnated with Nano-Zinc Oxide

Directory of Open Access Journals (Sweden)

Nami Kartal S

2010-01-01

Full Text Available Abstract Southern pine specimens vacuum-treated with nano-zinc oxide (nano-ZnO dispersions were evaluated for leach resistance and UV protection. Virtually, no leaching occurred in any of the nano-ZnO–treated specimens in a laboratory leach test, even at the highest retention of 13 kg/m3. However, specimens treated with high concentrations of nano-ZnO showed 58–65% chemical depletion after 12 months of outdoor exposure. Protection from UV damage after 12 months exposure is visibly obvious on both exposed and unexposed surfaces compared to untreated controls. Graying was markedly diminished, although checking occurred in all specimens. Nano-zinc oxide treatment at a concentration of 2.5% or greater provided substantial resistance to water absorption following 12 months of outdoor exposure compared to untreated and unweathered southern pine. We conclude that nano-zinc oxide can be utilized in new wood preservative formulations to impart resistance to leaching, water absorption and UV damage of wood.

Neural Network Modeling for the Extraction of Rare Earth Elements from Eudialyte Concentrate by Dry Digestion and Leaching

OpenAIRE

Yiqian Ma; Srecko Stopic; Lars Gronen; Milovan Milivojevic; Srdjan Obradovic; Bernd Friedrich

2018-01-01

Eudialyte is a promising mineral for rare earth elements (REE) extraction due to its good solubility in acid, low radioactive, and relatively high content of REE. In this paper, a two stage hydrometallurgical treatment of eudialyte concentrate was studied: dry digestion with hydrochloric acid and leaching with water. The hydrochloric acid for dry digestion to eudialyte concentrate ratio, mass of water for leaching to mass of eudialyte concentrate ratio, leaching temperature and leaching time ...

Caustic leaching of composite AZ-101/AZ-102 Hanford tank sludge

International Nuclear Information System (INIS)

Rapko, B.M.; Wagner, M.J.

1997-07-01

To reduce the quantity (and hence the cost) of glass canisters needed for disposing of high-level radioactive wastes from the Hanford tank farms, pretreatment processes are needed to remove as much nonradioactive material as possible. This report describes the results of a laboratory-scale caustic leaching test performed on a composite derived from a combination of 241-AZ-101 and 241-AZ-102 Hanford Tank sludges. The goals of this FY 1996 test were to evaluate the effectiveness of caustic leaching on removing key components from the sludge and to evaluate the effectiveness of varying the free-hydroxide concentrations by incrementally increasing the free hydroxide concentration of the leach steps up to 3 M free hydroxide. Particle-size analysis of the treated and untreated sludge indicated that the size and range of the sludge particles remained essentially unchanged by the caustic leaching treatment. Both before and after caustic leaching, a particle range of 0.2 microm to 50 microm was observed, with mean particle diameters of 8.5 to 9 microm based on the volume distribution and mean particle diameters of 0.3 to 0.4 microm based on the number distribution

Use of Polyphosphate to Decrease Uranium Leaching in Hanford 300 Area Smear Zone Sediments

Energy Technology Data Exchange (ETDEWEB)

Szecsody, James E.; Zhong, Lirong; Oostrom, Martinus; Vermeul, Vincent R.; Fruchter, Jonathan S.; Williams, Mark D.

2012-09-30

The primary objective of this study is to summarize the laboratory investigations performed to evaluate short- and long-term effects of phosphate treatment on uranium leaching from 300 area smear zone sediments. Column studies were used to compare uranium leaching in phosphate-treated to untreated sediments over a year with multiple stop flow events to evaluate longevity of the uranium leaching rate and mass. A secondary objective was to compare polyphosphate injection, polyphosphate/xanthan injection, and polyphosphate infiltration technologies that deliver phosphate to sediment.

Groundwater leaching of neutralized and untreated acid-leached uranium-mill tailings

International Nuclear Information System (INIS)

Gee, G.W.; Begej, C.W.; Campbell, A.C.; Sauter, N.N.; Opitz, B.E.; Sherwood, D.R.

1981-01-01

Tailings neutralization was examined to determine the effect of neutralization on contaminant release. Column leaching of acid extracted uranium mill tailings from Exxon Highland Mill, Wyoming, Pathfinder Gas Hills Mill, Wyoming, and the Dawn Midnite Mill, Washington, resulted in the flushing of high concentrations of salts in the first four pore volumes of leachate, followed by a steady decrease to the original groundwater salt concentrations. Neutralization decreased the concentration of salts and radionuclides leaching from the tailings and decreased the volume of solution required to return the solution to the groundwater pH and EC. Radium-226 and uranium-238 leached quickly from the tailings in the initial pore volumes of both neutralized and unneutralized tailings, and then decreased significantly. 6 figures, 5 tables

Pressure leaching of chalcopyrite concentrate

Science.gov (United States)

Aleksei, Kritskii; Kirill, Karimov; Stanislav, Naboichenko

2018-05-01

The results of chalcopyrite concentrate processing using low-temperature and high-temperature sulfuric acid pressure leaching are presented. A material of the following composition was used, 21.5 Cu, 0.1 Zn, 0.05 Pb, 0.04 Ni, 26.59 S, 24.52 Fe, 16.28 SiO2 (in wt.%). The influence of technological parameters on the degree of copper and iron extraction into the leach solution was studied in the wide range of values. The following conditions were suggested as the optimal for the high-temperature pressure leaching: t = 190 °C, PO2 = 0.5 MPa, CH2SO4 = 15 g/L, L:S = 6:1. At the mentioned parameters, it is possible to extract at least 98% Cu from concentrate into the leaching solution during 100 minutes. The following conditions were suggested as optimal for the low-temperature pressure leaching: t = 105 °C, PO2 = 1.3-1.5 MPa, CH2SO4 = 90 g/L, L:S = 10:1. At the mentioned parameters, it is possible to extract up to 83% Cu from the concentrate into the leach solution during 300-360 minutes.

Treatment of solid waste highly contaminated by alpha emitters: Recent developments of leaching process with continuous electrolyte regeneration

International Nuclear Information System (INIS)

Madic, C.; Lecomte, M.; Vigreux, B.

1990-01-01

Development of processes for leaching solid waste contaminated by alpha or alphaβgamma emitters has been pursued at the Nuclear Research Center in Fontenay-aux-Roses, France with the recent active commissioning of two pilot facilities: the Elise glove box system in February 1987 and the Prolixe shielded hot cell in March 1988. The Elise facility is designed to handle alpha waste and the Prolixe facility is designed to handle alphaβgamma waste. The common goal of the studies conducted in these facilities is to define the operating conditions for declassification of solid waste, i.e. to ensure that the alpha concentration of this waste will be less than 3.7 x 10 6 Bq/kg after treatment, packaging and decay prior to storage in surface repositories. The leaching process developed is mainly based on the continuous electrolytic regeneration of an aggressive agent, AgII, which can induce the dissolution of PuO 2 , the most difficult compound to remove from the solid waste. This paper summarizes recent achievements in the development of this process. 11 refs., 8 figs., 6 tabs

Treatment of solid waste highly contaminated by alpha emitters: recent developments of leaching process with continuous electrolyte regeneration

International Nuclear Information System (INIS)

Madic, C.; Lecomte, M.

1990-01-01

Development of processes for leaching solid waste contaminated by alpha or alpha/beta/gamma emitters has been pursued at the Nuclear Research Center in Fontenay-aux-Roses, France with the recent active commissioning of two pilot facilities: the Elise glove box system in February 1987 and the Prolixe shielded hot cell in March 1988. The Elise facility is designed to handle alpha waste and the Prolixe facility is designed to handle alpha/beta/gamma waste. The common goal of the studies conducted in these facilities is to define the operating conditions for declassification of solid waste, i.e. to ensure that the alpha concentration of this waste will be less than 3.7 x 10 6 Bq/kg after treatment, packaging and decay prior to storage in surface repositories. The leaching process developed is mainly based on the continuous electrolytic regeneration of an aggressive agent, AgII, which can induce the dissolution of PuO 2 , the most difficult compound to remove from the solid waste. This paper summarizes recent achievements in the development of this process

ALUMINUM AND CHROMIUM LEACHING WORKSHOP WHITEPAPER

International Nuclear Information System (INIS)

McCabe, D; Jeff Pike, J; Bill Wilmarth, B

2007-01-01

A workshop was held on January 23-24, 2007 to discuss the status of processes to leach constituents from High Level Waste (HLW) sludges at the Hanford and Savannah River Sites. The objective of the workshop was to examine the needs and requirements for the HLW flowsheet for each site, discuss the status of knowledge of the leaching processes, communicate the research plans, and identify opportunities for synergy to address knowledge gaps. The purpose of leaching of non-radioactive constituents from the sludge waste is to reduce the burden of material that must be vitrified in the HLW melter systems, resulting in reduced HLW glass waste volume, reduced disposal costs, shorter process schedules, and higher facility throughput rates. The leaching process is estimated to reduce the operating life cycle of SRS by seven years and decrease the number of HLW canisters to be disposed in the Repository by 1000 [Gillam et al., 2006]. Comparably at Hanford, the aluminum and chromium leaching processes are estimated to reduce the operating life cycle of the Waste Treatment Plant by 20 years and decrease the number of canisters to the Repository by 15,000-30,000 [Gilbert, 2007]. These leaching processes will save the Department of Energy (DOE) billions of dollars in clean up and disposal costs. The primary constituents targeted for removal by leaching are aluminum and chromium. It is desirable to have some aluminum in glass to improve its durability; however, too much aluminum can increase the sludge viscosity, glass viscosity, and reduce overall process throughput. Chromium leaching is necessary to prevent formation of crystalline compounds in the glass, but is only needed at Hanford because of differences in the sludge waste chemistry at the two sites. Improving glass formulations to increase tolerance of aluminum and chromium is another approach to decrease HLW glass volume. It is likely that an optimum condition can be found by both performing leaching and improving

Sulfur dioxide leaching of spent zinc-carbon-battery scrap

Energy Technology Data Exchange (ETDEWEB)

Avraamides, J.; Senanayake, G.; Clegg, R. [A.J. Parker Cooperative Research Centre for Hydrometallurgy, Murdoch University, Perth, WA 6150 (Australia)

2006-09-22

Zinc-carbon batteries, which contain around 20% zinc, 35% manganese oxides and 10% steel, are currently disposed after use as land fill or reprocessed to recover metals or oxides. Crushed material is subjected to magnetic separation followed by hydrometallurgical treatment of the non-magnetic material to recover zinc metal and manganese oxides. The leaching with 2M sulfuric acid in the presence of hydrogen peroxide recovers 93% Zn and 82% Mn at 25{sup o}C. Alkaline leaching with 6M NaOH recovers 80% zinc. The present study shows that over 90% zinc and manganese can be leached in 20-30min at 30{sup o}C using 0.1-1.0M sulfuric acid in the presence of sulfur dioxide. The iron extraction is sensitive to both acid concentration and sulfur dioxide flow rate. The effect of reagent concentration and particle size on the extraction of zinc, manganese and iron are reported. It is shown that the iron and manganese leaching follow a shrinking core kinetic model due to the formation of insoluble metal salts/oxides on the solid surface. This is supported by (i) the decrease in iron and manganese extraction from synthetic Fe(III)-Mn(IV)-Zn(II) oxide mixtures with increase in acid concentration from 1M to 2M, and (ii) the low iron dissolution and re-precipitation of dissolved manganese and zinc during prolonged leaching of battery scrap with low sulfur dioxide. (author)

Cross-current leaching of indium from end-of-life LCD panels

Energy Technology Data Exchange (ETDEWEB)

Rocchetti, Laura; Amato, Alessia; Fonti, Viviana [Department of Life and Environmental Sciences, Università Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy); Ubaldini, Stefano [Institute of Environmental Geology and Geoengineering IGAG, National Research Council, Via Salaria km 29300, 00015 Montelibretti, Rome (Italy); De Michelis, Ida [Department of Industrial Engineering, Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, 67100, Zona industriale di Pile, L’Aquila (Italy); Kopacek, Bernd [ISL Kopacek KG, Beckmanngasse 51, 1140 Wien (Austria); Vegliò, Francesco [Department of Industrial Engineering, Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, 67100, Zona industriale di Pile, L’Aquila (Italy); Beolchini, Francesca, E-mail: f.beolchini@univpm.it [Department of Life and Environmental Sciences, Università Politecnica delle Marche, Via Brecce Bianche, 60131 Ancona (Italy)

2015-08-15

Graphical abstract: Display Omitted - Highlights: • End-of-life LCD panels represent a source of indium. • Several experimental conditions for indium leaching have been assessed. • Indium is completely extracted with 2 M sulfuric acid at 80 °C for 10 min. • Cross-current leaching improves indium extraction and operating costs are lowered. • Benefits to the environment come from reduction of CO{sub 2} emissions and reagents use. - Abstract: Indium is a critical element mainly produced as a by-product of zinc mining, and it is largely used in the production process of liquid crystal display (LCD) panels. End-of-life LCDs represent a possible source of indium in the field of urban mining. In the present paper, we apply, for the first time, cross-current leaching to mobilize indium from end-of-life LCD panels. We carried out a series of treatments to leach indium. The best leaching conditions for indium were 2 M sulfuric acid at 80 °C for 10 min, which allowed us to completely mobilize indium. Taking into account the low content of indium in end-of-life LCDs, of about 100 ppm, a single step of leaching is not cost-effective. We tested 6 steps of cross-current leaching: in the first step indium leaching was complete, whereas in the second step it was in the range of 85–90%, and with 6 steps it was about 50–55%. Indium concentration in the leachate was about 35 mg/L after the first step of leaching, almost 2-fold at the second step and about 3-fold at the fifth step. Then, we hypothesized to scale up the process of cross-current leaching up to 10 steps, followed by cementation with zinc to recover indium. In this simulation, the process of indium recovery was advantageous from an economic and environmental point of view. Indeed, cross-current leaching allowed to concentrate indium, save reagents, and reduce the emission of CO{sub 2} (with 10 steps we assessed that the emission of about 90 kg CO{sub 2}-Eq. could be avoided) thanks to the recovery of indium

Technological studies on the Manisa-Koprubasi uranium ores of Turkey

International Nuclear Information System (INIS)

Sagdik, U.

1980-01-01

At the end of the laboratory and pilot plant scale technological experiments, three main types of ore have been classified: (i) Kasar type: The ores consist of secondary uranium mineralization (autunite, meta-autunite and torbenite) in loosely consolidated sands, gravels and clays of Neogene Age. Heap leaching has been carried out on 100 and 1000 t ore samples (0.05% U 3 O 8 ) under economical conditions, such as 20 to 40 kg of H 2 SO 4 per tonne of ore at ambient temperature; original size -20 cm, solid/liquid ratio of 10, 20 days, and 90% recovery of uranium has been reached. The uraniferous solutions (1 to 2 g of U 3 O 8 per litre) obtained from the heap leaching operations were purified in a solvent extraction unit with a capacity of 100 ltr/h by using an Alamine 336-kerosene-decanol solution. The uranium in the purified and concentrated solutions (15 g of U 3 O 8 per litre) was then precipitated as a yellow cake with 65 to 75% U 3 O 8 content by means of magnesia milk. (ii) Tasharman type: No specific uranium mineral has been detected in the mineralogical determination, although uranium is disseminated in phosphate minerals as dahllite and apatite. Uranium in the ore has been leached under rather uneconomical conditions; 100 kg of H 2 SO 4 per tonne of ore, particle size -1 cm, 25 0 C, 30 days. In the SX-treatment of pregnant solutions phosphate ions, higher acidity than pH 1, and compounds formed as a chemical precipitation, hindered the SX-recoveries. In such cases, the addition of acid, dilution of pregnant solutions, membrane filtration, or 40 0 C temperature have been applied to decrease the uranium loss in the raffinate. (iii) Carbonate type: Even if alkaline leaching at 65 0 C, or leaching with 400 kg of H 2 SO 4 per tonne of ore, was carried out on -200 mesh ore samples, no acceptable uranium recoveries were obtained

Life cycle assessment and residue leaching: The importance of parameter, scenario and leaching data selection

Energy Technology Data Exchange (ETDEWEB)

Allegrini, E., E-mail: elia@env.dtu.dk [Technical University of Denmark, Department of Environmental Engineering, Building 115, 2800 Lyngby (Denmark); Butera, S. [Technical University of Denmark, Department of Environmental Engineering, Building 115, 2800 Lyngby (Denmark); Kosson, D.S. [Vanderbilt University, Department of Civil and Environmental Engineering, Box 1831 Station B, Nashville, TN 37235 (United States); Van Zomeren, A. [Energy Research Centre of the Netherlands (ECN), Department of Environmental Risk Assessment, P.O. Box 1, 1755 ZG Petten (Netherlands); Van der Sloot, H.A. [Hans van der Sloot Consultancy, Dorpsstraat 216, 1721 BV Langedijk (Netherlands); Astrup, T.F. [Technical University of Denmark, Department of Environmental Engineering, Building 115, 2800 Lyngby (Denmark)

2015-04-15

Highlights: • Relevance of metal leaching in waste management system LCAs was assessed. • Toxic impacts from leaching could not be disregarded. • Uncertainty of toxicity, due to background activities, determines LCA outcomes. • Parameters such as pH and L/S affect LCA results. • Data modelling consistency and coverage within an LCA are crucial. - Abstract: Residues from industrial processes and waste management systems (WMSs) have been increasingly reutilised, leading to landfilling rate reductions and the optimisation of mineral resource utilisation in society. Life cycle assessment (LCA) is a holistic methodology allowing for the analysis of systems and products and can be applied to waste management systems to identify environmental benefits and critical aspects thereof. From an LCA perspective, residue utilisation provides benefits such as avoiding the production and depletion of primary materials, but it can lead to environmental burdens, due to the potential leaching of toxic substances. In waste LCA studies where residue utilisation is included, leaching has generally been neglected. In this study, municipal solid waste incineration bottom ash (MSWI BA) was used as a case study into three LCA scenarios having different system boundaries. The importance of data quality and parameter selection in the overall LCA results was evaluated, and an innovative method to assess metal transport into the environment was applied, in order to determine emissions to the soil and water compartments for use in an LCA. It was found that toxic impacts as a result of leaching were dominant in systems including only MSWI BA utilisation, while leaching appeared negligible in larger scenarios including the entire waste system. However, leaching could not be disregarded a priori, due to large uncertainties characterising other activities in the scenario (e.g. electricity production). Based on the analysis of relevant parameters relative to leaching, and on general results

Effect of Antifoam Agent on Oxidative Leaching of Hanford Tank Sludge Simulants

International Nuclear Information System (INIS)

Rapko, Brian M.; Jones, Susan A.; Lumetta, Gregg J.; Peterson, Reid A.

2010-01-01

Oxidative leaching of simulant tank waste containing an antifoam agent (AFA) to reduce the chromium content of the sludge was tested using permanganate as the oxidant in 0.25 M NaOH solutions. AFA is added to the waste treatment process to prevent foaming. The AFA, Dow Corning Q2-3183A, is a surface-active polymer that consists of polypropylene glycol, polydimethylsiloxane, octylphenoxy polyethoxy ethanol, treated silica, and polyether polyol. Some of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) waste slurries contain high concentrations of undissolved solids that would exhibit undesirable behavior without AFA addition. These tests were conducted to determine the effect of the AFA on oxidative leaching of Cr(III) in waste by permanganate. It has not previously been determined what effect AFA has on the permanganate reaction. This study was conducted to determine the effect AFA has on the oxidation of the chromium, plus plutonium and other criticality-related elements, specifically Fe, Ni and Mn. During the oxidative leaching process, Mn is added as liquid permanganate solution and is converted to an insoluble solid that precipitates as MnO2 and becomes part of the solid waste. Caustic leaching was performed followed by an oxidative leach at either 25 C or 45 C. Samples of the leachate and solids were collected at each step of the process. Initially, Battelle-Pacific Northwest Division (PNWD) was contracted by Bechtel National, Inc. to perform these further scoping studies on oxidative alkaline leaching. The data obtained from the testing will be used by the WTP operations to develop procedures for permanganate dosing of Hanford tank sludge solids during oxidative leaching. Work was initially conducted under contract number 24590-101-TSA-W000-00004. In February 2007, the contract mechanism was switched to Pacific Northwest National Laboratory (PNNL) operating Contract DE-AC05-76RL01830. In summary, this report describes work focused on determining

Effect of Antifoam Agent on Oxidative Leaching of Hanford Tank Sludge Simulants

Energy Technology Data Exchange (ETDEWEB)

Rapko, Brian M.; Jones, Susan A.; Lumetta, Gregg J.; Peterson, Reid A.

2010-02-26

Oxidative leaching of simulant tank waste containing an antifoam agent (AFA) to reduce the chromium content of the sludge was tested using permanganate as the oxidant in 0.25 M NaOH solutions. AFA is added to the waste treatment process to prevent foaming. The AFA, Dow Corning Q2-3183A, is a surface-active polymer that consists of polypropylene glycol, polydimethylsiloxane, octylphenoxy polyethoxy ethanol, treated silica, and polyether polyol. Some of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) waste slurries contain high concentrations of undissolved solids that would exhibit undesirable behavior without AFA addition. These tests were conducted to determine the effect of the AFA on oxidative leaching of Cr(III) in waste by permanganate. It has not previously been determined what effect AFA has on the permanganate reaction. This study was conducted to determine the effect AFA has on the oxidation of the chromium, plus plutonium and other criticality-related elements, specifically Fe, Ni and Mn. During the oxidative leaching process, Mn is added as liquid permanganate solution and is converted to an insoluble solid that precipitates as MnO2 and becomes part of the solid waste. Caustic leaching was performed followed by an oxidative leach at either 25°C or 45°C. Samples of the leachate and solids were collected at each step of the process. Initially, Battelle-Pacific Northwest Division (PNWD) was contracted by Bechtel National, Inc. to perform these further scoping studies on oxidative alkaline leaching. The data obtained from the testing will be used by the WTP operations to develop procedures for permanganate dosing of Hanford tank sludge solids during oxidative leaching. Work was initially conducted under contract number 24590-101-TSA-W000-00004. In February 2007, the contract mechanism was switched to Pacific Northwest National Laboratory (PNNL) operating Contract DE-AC05-76RL01830. In summary, this report describes work focused on

Utilizing on-farm best management practices: Managing Nitrate Leaching Using Evapotranspiration Based Irrigation Methods

Science.gov (United States)

Zaragosa, I.; Melton, F. S.; Dexter, J.; Post, K.; Haffa, A.; Kortman, S.; Spellenberg, R.; Cahn, M.

2017-12-01

In efforts to provide tools to allow farmers to optimize and quantify water usage and fertilizer applications, University of California Cooperative Extension (UCCE) developed the CropManage irrigation and nitrogen scheduling tool that provides real time evapotranspiration (ETc) based irrigation recommendations and fertilizer recommendations on a per field basis. CropManage incorporates satellite based estimates of fractional cover from web data services from the Satellite Irrigation Management Information Support (SIMS) system developed by NASA Ames Research Center in collaboration with California State University Monterey Bay (CSUMB). In this study, we conducted field trials to quantify the benefits of using these tools to support best management practices (BMPs) for irrigation and nutrient management in strawberries and lettuce in the Salinas Valley, California. We applied two different irrigation treatments based on full replacement (100%) of crop evapotranspiration (ETc), and irrigation at 130% of ETc replacement to approximate irrigation under business as usual irrigation management. Both field studies used a randomized block design with four replicates each. We used CropManage to calculate the 100% and 130% ETc replacement requirements prior to each irrigation event. We collected drainage volume and samples and analyzed them for 8500 to nitrate as (NO3-) concentrations. Experimental results for both strawberries and lettuce showed a significant decrease in the percentage of applied nitrogen leached for the 100% ETc replacement treatment against the 130% ETc replacement treatment. For strawberries, we observed that 24% of applied nitrogen was leached under the 100% ETc replacement treatment, versus 51% of applied nitrogen that was leached under the 130% ETc replacement treatment. For lettuce, we observe that 2% of the applied nitrogen leached bellow the soil profile, versus 6% of the applied nitrogen for the 130%ETc replacement treatment. In both experiments

Pesticide leaching through sandy and loamy fields – Long-term lessons learnt from the Danish Pesticide Leaching Assessment Programme

International Nuclear Information System (INIS)

Rosenbom, Annette E.; Olsen, Preben; Plauborg, Finn; Grant, Ruth; Juhler, René K.; Brüsch, Walter; Kjær, Jeanne

2015-01-01

The European Union authorization procedure for pesticides includes an assessment of the leaching risk posed by pesticides and their degradation products (DP) with the aim of avoiding any unacceptable influence on groundwater. Twelve-year's results of the Danish Pesticide Leaching Assessment Programme reveal shortcomings to the procedure by having assessed leaching into groundwater of 43 pesticides applied in accordance with current regulations on agricultural fields, and 47 of their DP. Three types of leaching scenario were not fully captured by the procedure: long-term leaching of DP of pesticides applied on potato crops cultivated in sand, leaching of strongly sorbing pesticides after autumn application on loam, and leaching of various pesticides and their DP following early summer application on loam. Rapid preferential transport that bypasses the retardation of the plow layer primarily in autumn, but also during early summer, seems to dominate leaching in a number of those scenarios. - Highlights: • Field-results reveal shortcomings in the EU authorization procedure for pesticides. • The plough layer can be bypassed via preferential transport in e.g. wormholes. • Pesticides properties are decisive for leaching pattern on the sandy fields. • The hydrogeological settings control the leaching patterns on the loamy fields. • Pesticide detection frequency seems to be independent of the month of the year. - Long-term lessons learnt from the Danish Pesticide Leaching Assessment Programme reveals shortcomings in the European Union authorization procedure for pesticides

Process for controlling calcium in a leach operation

International Nuclear Information System (INIS)

Habib, E.J.

1982-01-01

A method for controlling calcium, e.g. calcite, build-up in the leach solution of a uranium and/or related values recovery operation wherein the leach solution is flowed through a value bearing ore to dissolve the desired values. A soluble fluoride, e.g. sodium fluoride, is added to the leach solution after it has passed through the ore to thereby precipitate calcium fluoride from the leach solution and lower the calcium content of the leach solution. The soluble fluoride may be added to the leach solution before the leach solution passes through the process equipment which is used to remove the values from the leach solution or the soluble fluoride may be added after the leach solution passes through the process equipment. If added before, it is preferable to also add a carbonate/bicarbonate solution along with the soluble fluoride to prevent coprecipitation of uranyl/desired value fluoride or to redissolve coprecipitated fluoride back into the leach solution

Uranium production and environmental restoration at Priargunsky Centre (Russian Federation)

International Nuclear Information System (INIS)

Shatalov, V.V.; Boitsov, A.V.; Nikolsky, A.L.; Chernigov, V.G.; Ovseichuk, V.A.

2002-01-01

The state enterprise 'Priargunsky Mining and Chemical Production Association' (PPGHO) is the only active uranium production centre in Russia in last decade. Mining has been operated since 1968 by two open pits and four underground mines. It is based on resources of 19 volcanic-type deposits of Streltsovsk U-ore region situated at the area of 150 km 2 . Milling and processing has been carried out since 1974 at the local hydrometallurgical plant. Since the mid 1980s, limited amount of uranium is produced by heap and block leaching methods. High level of total production marks PPGHO as one of the outstanding uranium production centers worldwide. Significant amount of solid, liquid and gas wastes have been generated for more than 30 years. The principal environmental contamination comes from waste rock piles, mine water and tailing ponds. Liquid waste seepage through tailing pond bed can essentially contaminate underground waters. The principal environmental remediation activities are: waste rock dumps and open pits rehabilitation; waste rock utilization for industrial needs; heap and block leaching mining development, strengthening dam bodies and construction intercepting wells below the tailing pond dam, hydrogeological monitoring, upgrade of mine water treatment unit. Waste is being managed by the environmental service team of PPGHO. Environmental restoration activities, including rehabilitation of the territories and waste utilization, are implemented gradually in line with decommissioning of enterprise's particular facilities. (author)

10 CFR 171.16 - Annual fees: Materials licensees, holders of certificates of compliance, holders of sealed source...

Science.gov (United States)

2010-01-01

.... 4 Another license includes licenses for extraction of metals, heavy metals, and rare earths. 5 There..., in-situ recovery, heap-leaching, ore buying stations, ion exchange facilities and in-processing of ores containing source material for extraction of metals other than uranium or thorium, including...

77 FR 46091 - Notice of Proposed Administrative Settlement Pursuant to the Comprehensive Environmental Response...

Science.gov (United States)

2012-08-02

... to the Comprehensive Environmental Response, Compensation, and Liability Act, As Amended; Anaconda.... SUMMARY: In accordance with Section 122(i) of the Comprehensive Environmental Response, Compensation, and... fund up to $420,000 toward a response action by EPA to address releases from the Arimetco heap leach...

Treatment of metallurgical wastes : recovery of metal values from smelter slags by pressure oxidative leaching

Energy Technology Data Exchange (ETDEWEB)

Li, Y.; Perederiy, I.; Papangelakis, V.G. [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

2008-07-01

Vast quantities of slag are produced and dumped as waste by-products during the production of base metals by smelting operations. These slags contain large amounts of valuable metals which lead to a decrease in metal yield and, combined with the entrapped sulphur, pose a danger to the environment. The dissolution of fayalite is important for the selective recovery of valuable metals and the cleanup of slags in high pressure oxidative leaching. The nature of base metals and iron in solidified slag must be investigated in order to understand the mechanism of the process. This paper discussed the application of powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM) for the characterization of a smelter slag microstructure. The study used leaching tests with the same smelter slag to measure and monitor the results of leaching, including metal extraction levels, the extent of iron dissolution as well as impurity contents. The paper provided information on the experiment with particular reference to slag leaching, chemical analysis, and characterization. It was concluded that slag consists of several solid phases with base metal sulfide and oxide droplets entrapped in the fayalite matrix or silica regions. Therefore, nickel, copper, cobalt, and zinc need to be exposed either chemically or mechanically to promote their recovery. 21 refs., 4 tabs., 5 figs.

Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

OpenAIRE

Gongxin Chen; Zhanxue Sun; Yajie Liu

2016-01-01

Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. Howev...

Low leach rate glasses for immobilization of nuclear wastes

International Nuclear Information System (INIS)

Chick, L.A.; Buckwalter, C.Q.

1980-10-01

Improved defense and commercial waste glass have about one order of magnitude lower leach rates at 90 0 C in static deionized water than reference glasses. This durability difference diminishes as the leaching temperature is raised, but at repository temperature less than 150 0 C, the improved compositions would have considerable advantages over reference glases. At the melting temperatures necessary for most of the high-durability glasses, volatility was found to be higher than that experienced in processing current reference glases. Higher volatilities might be compensated for by specific design of the off-gas system for improved off-gas treatment and volatile materials recovery. 6 figures, 2 tables

Statistical comparison of leaching behavior of incineration bottom ash using seawater and deionized water: Significant findings based on several leaching methods.

Science.gov (United States)

Yin, Ke; Dou, Xiaomin; Ren, Fei; Chan, Wei-Ping; Chang, Victor Wei-Chung

2018-02-15

Bottom ashes generated from municipal solid waste incineration have gained increasing popularity as alternative construction materials, however, they contains elevated heavy metals posing a challenge for its free usage. Different leaching methods are developed to quantify leaching potential of incineration bottom ashes meanwhile guide its environmentally friendly application. Yet, there are diverse IBA applications while the in situ environment is always complicated, challenging its legislation. In this study, leaching tests were conveyed using batch and column leaching methods with seawater as opposed to deionized water, to unveil the metal leaching potential of IBA subjected to salty environment, which is commonly encountered when using IBA in land reclamation yet not well understood. Statistical analysis for different leaching methods suggested disparate performance between seawater and deionized water primarily ascribed to ionic strength. Impacts of leachant are metal-specific dependent on leaching methods and have a function of intrinsic characteristics of incineration bottom ashes. Leaching performances were further compared on additional perspectives, e.g. leaching approach and liquid to solid ratio, indicating sophisticated leaching potentials dominated by combined geochemistry. It is necessary to develop application-oriented leaching methods with corresponding leaching criteria to preclude discriminations between different applications, e.g., terrestrial applications vs. land reclamation. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation of Iron Nanoparticles by Selective Leaching Method

Czech Academy of Sciences Publication Activity Database

Michalcová, A.; Vojtěch, D.; Kubatík, Tomáš František; Stehlíková, K.; Brabec, F.; Marek, I.

2015-01-01

Roč. 128, č. 4 (2015), s. 640-642 ISSN 0587-4246. [International Symposium on Physics of Materials (ISPMA) /13./. Prague, 31.08.2014-04.09.2014] Institutional support: RVO:61389021 Keywords : Iron nanoparticles * selective leaching method Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 0.525, year: 2015

Environmental Hazard Assessment of Jarosite Waste Using Batch Leaching Tests

Directory of Open Access Journals (Sweden)

M. Kerolli – Mustafa

2018-01-01

Full Text Available Jarosite waste samples from Trepça Zinc Industry in Kosovo were subjected to two batch leaching tests as an attempt to characterize the leaching behavior and mobility of minor and major elements of jarosite waste. To achieve this, deionized water and synthetic acidic rain leaching tests were employed. A two-step acidic treatment in microwave digestion system were used to dissolve jarosite waste samples, followed by determination of Al, Ag, As, Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, P, Pb, S, Si, Sr, and Zn by inductively coupled plasma optical emission spectrometry (ICP-OES. The validation of the procedure was performed by the analysis of two geochemical reference materials, S JR-3 and S Jsy-1. Two toxicity leaching tests revealed a high metal releasing of Cd, Cu, Ni, Mn, Pb, Zn, and As, and the metal release risk for these elements is still very high due the low pH and acid rain. The statistical analysis showed useful data information on the relationship between elements in jarosite samples in two different extraction conditions (deionized water and synthetic acid rain.

The structure of leached sodium borosilicate glass

International Nuclear Information System (INIS)

Bunker, B.C.; Tallant, D.R.; Headley, T.J.; Turner, G.L.; Kirkpatrick, R.J.

1988-01-01

Raman spectroscopy, solid state 29 Si, 11 B, 17 O, and 23 Na nuclear magnetic resonance spectroscopy, and transmission electron microscopy have been used to investigate how the structures of sodium borosilicate glasses change during leaching in water at pH 1, 9, and 12. Results show that the random network structure present prior to leaching is transformed into a network of small condensed ring structures and/or colloidal silica particles. The restructuring of leached glass can be rationalised on the basis of simple hydrolysis (depolymerisation) and condensation (repolymerisation) reactions involving Si-O-Si and Si-O-B bonds. The structural changes that occur during leaching influence the properties of the leached layer, including leaching kinetics, crazing and spalling, and slow crack growth. (author)

Precipitation of uranium peroxide from the leach liquor of uranium ores

International Nuclear Information System (INIS)

Gao Xizhen; Lin Sirong; Guo Erhua; Lu Shijie

1995-06-01

A chemical precipitation process of recovering uranium from the leach liquor of uranium ores was investigated. The process primarily includes the precipitation of iron with lime, the preprocessing of the slurry of iron hydroxides and the precipitation of uranium with H 2 O 2 . The leach liquor is neutralized by lime milk to pH 3.7 to precipitate the iron hydroxides which after flocculation and settle is separated out and preprocessed at 170 degree C in an autoclave. H 2 O 2 is then used to precipitate uranium in the leach liquor free of iron, and the pH of process for uranium precipitation adjusted by adding MgO slurry to 3.5. The barren solution can be used to wash the filter cakes of leach tailing. The precipitated slurry of iron hydroxides after being preprocessed is recycled to leaching processes for recovering uranium in it. This treatment can not only avoid the filtering of the slurry of iron hydroxides, but also prevent the iron precipitate from redissolving and consequently the increase of iron concentration in the leach liquor. The results of the investigation indicate that lime, H 2 O 2 and MgO are the main chemical reagents used to obtain the uranium peroxide product containing over 65% uranium from the leach liquor, and they also do not cause environmental pollution. In accordance with the uranium content in the liquor, the consumption of chemical reagent for H 2 O 2 (30%) and MgO are 0.95 kg/kgU and 0.169 kg/kgU, respectively. (1 fig., 8 tabs., 7 refs.)

LCA of management strategies for RDF incineration and gasification bottom ash based on experimental leaching data.

Science.gov (United States)

Di Gianfilippo, Martina; Costa, Giulia; Pantini, Sara; Allegrini, Elisa; Lombardi, Francesco; Astrup, Thomas Fruergaard

2016-01-01

The main characteristics and environmental properties of the bottom ash (BA) generated from thermal treatment of waste may vary significantly depending on the type of waste and thermal technology employed. Thus, to ensure that the strategies selected for the management of these residues do not cause adverse environmental impacts, the specific properties of BA, in particular its leaching behavior, should be taken into account. This study focuses on the evaluation of potential environmental impacts associated with two different management options for BA from thermal treatment of Refuse Derived Fuel (RDF): landfilling and recycling as a filler for road sub bases. Two types of thermal treatment were considered: incineration and gasification. Potential environmental impacts were evaluated by life-cycle assessment (LCA) using the EASETECH model. Both non-toxicity related impact categories (i.e. global warming and mineral abiotic resource depletion) and toxic impact categories (i.e. human toxicity and ecotoxicity) were assessed. The system boundaries included BA transport from the incineration/gasification plants to the landfills and road construction sites, leaching of potentially toxic metals from the BA, the avoided extraction, crushing, transport and leaching of virgin raw materials for the road scenarios, and material and energy consumption for the construction of the landfills. To provide a quantitative assessment of the leaching properties of the two types of BA, experimental leaching data were used to estimate the potential release from each of the two types of residues. Specific attention was placed on the sensitivity of leaching properties and the determination of emissions by leaching, including: leaching data selection, material properties and assumptions related to emission modeling. The LCA results showed that for both types of BA, landfilling was associated with the highest environmental impacts in the non-toxicity related categories. For the toxicity

Acid leaching of natural chrysotile asbestos to mesoporous silica fibers

Science.gov (United States)

Maletaškić, Jelena; Stanković, Nadežda; Daneu, Nina; Babić, Biljana; Stoiljković, Milovan; Yoshida, Katsumi; Matović, Branko

2018-04-01

Nanofibrous silica with a high surface area was produced from chrysotile by the acid-leaching method. Natural mineral chrysotile asbestos from Stragari, Korlace in Serbia was used as the starting material. The fibers were modified by chemical treatment with 1 M HCl and the mineral dissolution was monitored by transmission electron microscopy, X-ray powder diffraction, inductively coupled plasma spectrometry and low-temperature nitrogen adsorption techniques to highlight the effects of the leaching process. The results showed that the applied concentration of acid solution and processing time of 4 h were sufficient to effectively remove the magnesium hydroxide layer and transform the crystal structure of the hazardous starting chrysotile to porous SiO2 nanofibers. With prolonged acid leaching, the specific surface area, S BET, calculated by BET equation, was increased from 147 up to 435 m2 g- 1, with micropores representing a significant part of the specific surface.

Rare earth elements leaching from Tin slag using Acid Chloride after Alkaline fusion process

International Nuclear Information System (INIS)

Kurnia Trinopiawan; Budi Yuli Ani; June Mellawati; Mohammad Zaki Mubarok

2016-01-01

Tin slag, a waste product from tin smelting process, has a potency to be utilized further by extracting the valuable metals inside, such as rare earth elements(REE). The objective of this study is to determine the optimum leaching condition of REE from tin slag after alkali fusion. Silica structure in slag is causing the direct leaching uneffectively. Therefore, pre-treatment step using alkali fusion is required to break the structure of silica and to increase the porosity of slag. Fusion is conducted in 2 hours at 700°C, with ratio of natrium hydroxide (NaOH) : slag = 2 : 1. Later, frit which is leached by water then leached by chloride acid to dissolve REE. As much as 87,5% of REE is dissolved at 2 M on chloride acid (HCl) concentration, in 40°C temperature, -325 mesh particle size, 15 g/100 ml of S/L, 150 rpm of agitation speed, and 5 minutes of leaching time. (author)

Mine waste management

International Nuclear Information System (INIS)

Hutchinson, I.P.G.; Ellison, R.D.

1992-01-01

This book reports on mine waste management. Topics covered include: Performance review of modern mine waste management units; Mine waste management requirements; Prediction of acid generation potential; Attenuation of chemical constituents; Climatic considerations; Liner system design; Closure requirements; Heap leaching; Ground water monitoring; and Economic impact evaluation

EFRT M-12 Issue Resolution: Caustic-Leach Rate Constants from PEP and Laboratory-Scale Tests

Energy Technology Data Exchange (ETDEWEB)

Mahoney, Lenna A.; Rassat, Scot D.; Eslinger, Paul W.; Aaberg, Rosanne L.; Aker, Pamela M.; Golovich, Elizabeth C.; Hanson, Brady D.; Hausmann, Tom S.; Huckaby, James L.; Kurath, Dean E.; Minette, Michael J.; Sundaram, S. K.; Yokuda, Satoru T.

2010-01-01

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes” of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing. The work described in this report addresses caustic leaching under WTP conditions, based on tests performed with a Hanford waste simulant. Because gibbsite leaching kinetics are rapid (gibbsite is expected to be dissolved by the time the final leach temperature is reached), boehmite leach kinetics are the main focus of the caustic-leach tests. The tests were completed at the laboratory-scale and in the PEP, which is a 1/4.5-scale mock-up of key PTF process equipment. Two laboratory-scale caustic-leach tests were performed for each of the PEP runs. For each PEP run, unleached slurry was taken from the PEP caustic-leach vessel for one batch and used as feed for both of the corresponding laboratory-scale tests.

Long-term leaching from MSWI air-pollution-control residues: Leaching characterization and modeling

DEFF Research Database (Denmark)

Hyks, Jiri; Astrup, Thomas; Christensen, Thomas Højlund

2009-01-01

Long-term leaching of Ca, Fe, Mg, K, Na, S, Al, As, Ba, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Mo, Sb, Si, Sri, Sr, Ti, V, P, Cl, and dissolved organic carbon from two different municipal solid waste incineration (MSWI) air-pollution-control residues was monitored during 24 months of column percolat......Long-term leaching of Ca, Fe, Mg, K, Na, S, Al, As, Ba, Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Mo, Sb, Si, Sri, Sr, Ti, V, P, Cl, and dissolved organic carbon from two different municipal solid waste incineration (MSWI) air-pollution-control residues was monitored during 24 months of column...... percolation experiments; liquid-to-solid (L/S) ratios of 200-250 L/kg corresponding to more than 10,000 years in a conventional landfill were reached. Less than 2% of the initially present As, Cu, Pb, Zn, Cr, and Sb had leached during the Course of the experiments. Concentrations of Cd, Fe, Mg, Hg, Mn, Ni, Co......, Sn, Ti, and P were generally bellow 1 mu g/L; overall less than 1% of their mass leached. Column leaching data were further used in a two-step geochemical modeling in PHREEQC in order to (i) identify solubility controlling minerals and (ii) evaluate their interactions in a water-percolated column...

Impacts of new environmental and safety regulations on uranium mining, milling and waste management in China

International Nuclear Information System (INIS)

Wang Yongping; Zheng Yuhui; Shi Xiangjun

2001-01-01

Nuclear power progress has triggered the development and innovation of nuclear fuel industries in China. At present the Chinese government has put more emphasis on industrial readjustment and technical innovation in uranium mining and milling in order to fuel the nuclear power development, satisfy environmental protection and improve economic efficiency of the industry. The current organizations and approval procedure for establishing regulations and the implementation and consequences of the regulations, technical polices and development strategies concerning uranium mining, milling, treatment of waste ores and mill tailings, and reduction of the workers' suffered exposure dose etc. in China are discussed and the economic, health and environmental impacts of the uranium mining and metallurgy with reformation achievement and the introduction of advanced technologies such as the in-situ leaching and heap leaching mining technologies are assessed in this paper. (author)

Evaluation of leaching behavior and immobilization of zinc in cement-based solidified products

Directory of Open Access Journals (Sweden)

Krolo Petar

2012-01-01

Full Text Available This study has examined leaching behavior of monolithic stabilized/solidified products contaminated with zinc by performing modified dynamic leaching test. The effectiveness of cement-based stabilization/solidification treatment was evaluated by determining the cumulative release of Zn and diffusion coefficients, De. The experimental results indicated that the cumulative release of Zn decreases as the addition of binder increases. The values of the Zn diffusion coefficients for all samples ranged from 1.210-8 to 1.1610-12 cm2 s-1. The samples with higher amounts of binder had lower De values. The test results showed that cement-based stabilization/solidification treatment was effective in immobilization of electroplating sludge and waste zeolite. A model developed by de Groot and van der Sloot was used to clarify the controlling mechanisms. The controlling leaching mechanism was found to be diffusion for samples with small amounts of waste material, and dissolution for higher waste contents.

Treatment of solid waste highly contaminated by alpha emitters. Recent developments of leaching process with continuous electrolyte regeneration

International Nuclear Information System (INIS)

Madic, C.

1990-01-01

In the recent years, efforts have been made in order to reduce the amount of alpha emitters essentially plutonium isotopes present in the solid wastes produced during research experiments on fuel reprocessing. Leaching processes using electrogenerated Ag (II(a very agressive agent for PuO 2 )) in nitric acid solutions, were developed and several facilities were designed and built to operate the processes: (1) ELISE and PROLIXE facilities, for the treatment of α and α, β, γ solid wastes (CEA, FONTENAY-AUX-ROSES) (2) PILOT ASHES FACILITY for delete, the treatment of plutonium contaminated ashes (COGEMA, MARCOULE). A brief description of the process and of the different facilities is presented; the main results obtained in ELISE and PROLIXE are also summarized

EFRT M-12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

Energy Technology Data Exchange (ETDEWEB)

Rapko, Brian M.; Schonewill, Philip P.; Brown, Christopher F.; Eslinger, Paul W.; Fountain, Matthew S.; Hausmann, Tom S.; Huckaby, James L.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

2010-01-01

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes” of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

EFRT M-12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

International Nuclear Information System (INIS)

Rapko, Brian M.; Schonewill, Philip P.; Brown, Christopher F.; Eslinger, Paul W.; Fountain, Matthew S.; Hausmann, Tom S.; Huckaby, James L.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

2010-01-01

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, 'Undemonstrated Leaching Processes' of the External Flowsheet Review Team (EFRT) issue response plan. The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

Life cycle assessment and residue leaching: the importance of parameter, scenario and leaching data selection.

Science.gov (United States)

Allegrini, E; Butera, S; Kosson, D S; Van Zomeren, A; Van der Sloot, H A; Astrup, T F

2015-04-01

Residues from industrial processes and waste management systems (WMSs) have been increasingly reutilised, leading to landfilling rate reductions and the optimisation of mineral resource utilisation in society. Life cycle assessment (LCA) is a holistic methodology allowing for the analysis of systems and products and can be applied to waste management systems to identify environmental benefits and critical aspects thereof. From an LCA perspective, residue utilisation provides benefits such as avoiding the production and depletion of primary materials, but it can lead to environmental burdens, due to the potential leaching of toxic substances. In waste LCA studies where residue utilisation is included, leaching has generally been neglected. In this study, municipal solid waste incineration bottom ash (MSWI BA) was used as a case study into three LCA scenarios having different system boundaries. The importance of data quality and parameter selection in the overall LCA results was evaluated, and an innovative method to assess metal transport into the environment was applied, in order to determine emissions to the soil and water compartments for use in an LCA. It was found that toxic impacts as a result of leaching were dominant in systems including only MSWI BA utilisation, while leaching appeared negligible in larger scenarios including the entire waste system. However, leaching could not be disregarded a priori, due to large uncertainties characterising other activities in the scenario (e.g. electricity production). Based on the analysis of relevant parameters relative to leaching, and on general results of the study, recommendations are provided regarding the use of leaching data in LCA studies. Copyright © 2014 Elsevier Ltd. All rights reserved.

Uranium extraction history using pressure leaching

International Nuclear Information System (INIS)

Fraser, K.S.; Thomas, K.G.

2010-01-01

Over the past 60 years of uranium process development only a few commercial uranium plants have adopted a pressure leaching process in their flowsheet. The selection of acid versus alkaline pressure leaching is related to the uranium and gangue mineralogy. Tetravalent (U"+"4) uranium has to be oxidized to hexavalent (U"+"6) uranium to be soluble. Refractory tetravalent uranium requires higher temperature and pressure, as practised in pressure leaching, for conversation to soluble hexavalent uranium. This paper chronicles the history of these uranium pressure leaching facilities over the past 60 years, with specific details of each design and operation. (author)

A new Leaching System, Sheta Extractor

International Nuclear Information System (INIS)

Sheta, M.E.

2008-01-01

Moving of crushed solid ores against leaching solution in a continuous countercurrent arises a true technical problem. This invented system introduces a practical solution for such problem. Inside the system, the crushed ore is driving against gravity, whereas the leaching solution moves in the opposite direction. Contact between the two phases occurs with gentle stirring. After contact, discharging of the processed phases takes place automatically out the system. The system was investigated for uranium leaching from a coarse grained fraction (+2 --- -- -30 mm) of uranium mineralized granite sample. Uranium leaching percent reached to nearly 50% using sulfuric acid

Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 2: Leaching characteristics of bottom ashes.

Science.gov (United States)

Baun, Dorthe L; Christensen, Thomas H; Bergfeldt, Brita; Vehlow, Jürgen; Mogensen, Erhardt P B

2004-02-01

With the perspective of generating only one solid residue from waste incineration, co-feeding of municipal solid waste and air pollution control residues stabilized by the Ferrox process was investigated in the TAMARA pilot plant incinerator as described in Bergfeldt et al. (Waste Management Research, 22, 49-57, 2004). This paper reports on leaching from the combined bottom ashes. Batch leaching test, pH-static leaching tests, availability tests and column leaching tests were used to characterize the leaching properties. The leaching properties are key information in the context of reuse in construction or in landfilling of the combined residue. In general, the combined bottom ashes had leaching characteristics similar to the reference bottom ash, which contained no APC residue. However, As and Pb showed slightly elevated leaching from the combined bottom ashes, while Cr showed less leaching. The investigated combined bottom ashes had contents of metals comparable to what is expected at steady state after continuous co-feeding of APC residues. Only Cd and Pb were partly volatilized (30-40%) during the incineration process and thus the combined bottom ashes had lower contents of Cd and Pb than expected at steady state. Furthermore, a major loss of Hg was, not surprisingly, seen and co-feeding of Ferrox-products together with municipal solid waste will require dedicated removal of Hg in the flue gas to prevent a build up of Hg in the system. In spite of this, a combined single solid residue from waste incineration seems to be a significant environmental improvement to current technology.

Titanium leaching from red mud by diluted sulfuric acid at atmospheric pressure

International Nuclear Information System (INIS)

Agatzini-Leonardou, S.; Oustadakis, P.; Tsakiridis, P.E.; Markopoulos, Ch.

2008-01-01

Laboratory-scale research has focused on the recovery of titanium from red mud, which is obtained from bauxite during the Bayer process for alumina production. The leaching process is based on the extraction of this element with diluted sulfuric acid from red mud under atmospheric conditions and without using any preliminary treatment. Statistical design and analysis of experiments were used, in order to determine the main effects and interactions of the leaching process factors, which were: acid normality, temperature and solid to liquid ratio. The titanium recovery efficiency on the basis of red mud weight reached 64.5%. The characterization of the initial red mud, as well as this of the leached residues was carried out by X-ray diffraction, TG-DTA and scanning electron microscopy

Applications of imaging spectroscopy data: A case study at Summitville, Colorado

Science.gov (United States)

King, Trude V.V.; Clark, Roger N.; Swayze, Gregg A.

2000-01-01

contact with mineralized rocks, a process that may be enhanced by bacterial action. The resulting fluids may be highly toxic and, when mixed with groundwater, surface water, and soil, may have harmful effects on humans, animals, and plants. Thus, understanding the geologic and hydrologic history of this area is a critical piece of the environmental puzzle in the Summitville area. The Summitville mine operators had ceased active mining and begun environmental remediation, including treatment of the heap-leach pile and installation of a water-treatment facility, when it declared bankruptcy in December 1992 and abandoned the mine site. The U.S. Environmental Protection Agency (EPA) immediately took over the Summitville site under EPA Superfund Emergency Response authority. Summitville has focused public attention on the environmental effects of modern mineral-resource development. Soon after the mine was abandoned, Federal, State, and local agencies, along with Alamosa River water users and private companies, began extensive studies at the mine site and surrounding areas. These studies included analysis of water, soil, livestock and vegetation. The role of the U.S. Geological Survey (USGS) was to provide geologic, hydrologic and agricultural information about the mine and surrounding area and to describe and evaluate the environmental condition of the Summitville mine and the downstream effects of the mine on the San Luis Valley (King 1995).

Leaching mechanisms of constituents from fly ash under the influence of humic acid.

Science.gov (United States)

Zhao, Shengxin; Chen, Zhonglin; Shen, Jimin; Kang, Jing; Zhang, Jin; Shen, Yanqing

2017-01-05

As a low-cost material for adsorption, FA is one of the most efficient adsorbents of HA. However, the leaching of elements from FA is problematic during utilization in water treatment. In this investigation, the potential leaching behaviors of Calcium, Arsenic, Born, Chromium, and other elements from FA in HA solution were studied via batch test. The data show that HA had an effect on the leaching of each element of FA, depending on the pH, the initial concentration of HA and the addition of calcium oxide (CaO). The Langmuir isotherm could better fit the equilibrium data in different initial concentrations of HA from 10 to 100mg/L. Because of the interaction between HA and the FA leaching elements, multi-layer adsorption occurred when the initial concentration of HA was more than 100mg/L. The pH and free CaO content played major roles in HA adsorption and FA leaching. Using SEM and XRD to characterize the solid of FA being mixed with CaO treated in solution, the results demonstrated that the reaction between FA and CaO could generate crystal minerals, such as portlandite, gismondine, ettringite (AFt) and calcite, which effectively restrained the leaching of elements, reduced secondary pollution. Copyright © 2016 Elsevier B.V. All rights reserved.

Impact of chemical leaching on permeability and cadmium removal from fine-grained soils.

Science.gov (United States)

Lin, Zhongbing; Zhang, Renduo; Huang, Shuang; Wang, Kang

2017-08-01

The aim of this study was to investigate the influence of chemical leaching on permeability and Cd removal from fine-grained polluted soils. Column leaching experiments were conducted using two types of soils (i.e., artificially Cd-polluted loam and historically polluted silty loam). Chemical agents of CaCl 2 , FeCl 3 , citric acid, EDTA, rhamnolipid, and deionized water were used to leach Cd from the soils. Results showed that organic agents reduced permeability of both soils, and FeCl 3 reduced permeability of loam soil, compared with inorganic agents and deionized water. Entrapment and deposition of colloids generated from the organic agents and FeCl 3 treatments reduced the soil permeability. The peak Cd effluence from the artificially polluted loam columns was retarded. For the artificially polluted soils treated with EDTA and the historically polluted soils with FeCl 3 , Cd precipitates were observed at the bottom after chemical leaching. When Cd was associated with large colloid particles, the reduction of soil permeability caused Cd accumulation in deeper soil. In addition, the slow process of disintegration of soil clay during chemical leaching might result in the retardation of peak Cd effluence. These results suggest the need for caution when using chemical-leaching agents for Cd removal in fine-grained soils.

Microbial leaching of low grade sandstone uranium ores: column leaching studies

International Nuclear Information System (INIS)

Bhatti, T.M.; Malik, K.A.; Khalid, A.M.

1991-01-01

Microbial leaching studies on a low-grade sandstone uranium ore from Baghalchur Ore Deposits, D. G. Khan, Pakistan, containing 0.027 % U/sub 3/O/sub 8/ for extraction of uranium, were conducted in columns. Baghalchur sandstone uranium ore which is alkaline in nature, contained 5.0% calcite [CaCo/sub 3/], 2-3 % Fe/sub 2/O/sub 3/ and pyrite [FeS/sub 2/] less than 0.1 %. The ore amended with sulfur and/or sulfur slag as external energy source was found to leach with indigenous microflora mostly belonging to the genus Thiobacillus which are present in the uranium mine water. Column leaching studies revealed that when the ore was amended with elemental sulfur and irrigated with mine water (pH 3.5) 53 % U/sub 3/O/sub 8/ could be solubilized from it. However, when the natural mine water was used as such (pH 7.4) the solubilization of uranium was decreased to 41 % U/sub 3/O/sub 8/ in 90 days under similar conditions of percolation rate and temperature. The addition of (NH/sub 4/)/sub 2/SO/sub 4/ (3.0 g/L) in mine water was found to enhance the uranium leaching to 70 % U/sub 3/O/sub 8/ from the columns containing ore amended with sulfur slag. (author)

Leaching behavior of simulated high-level waste glass

International Nuclear Information System (INIS)

Kamizono, Hiroshi

1987-03-01

The author's work in the study on the leaching behavior of simulated high-level waste (HLW) glass were summarized. The subjects described are (1) leach rates at high temperatures, (2) effects of cracks on leach rates, (3) effects of flow rate on leach rates, and (4) an in-situ burial test in natural groundwater. In the following section, the leach rates obtained by various experiments were summarized and discussed. (author)

PRESERVATIVE LEACHING FROM WEATHERED CCA-TREATED WOOD

Science.gov (United States)

Disposal of discarded CCA-treated wood in landfills raises concerns with respect to leaching of preservative compounds. When unweathered CCA-treated wood is leached using the toxicity characteristic leaching procedure (TCLP), arsenic concentrations exceed the toxicity characteris...

Dynamic leaching test of personal computer components.

Science.gov (United States)

Li, Yadong; Richardson, Jay B; Niu, Xiaojun; Jackson, Ollie J; Laster, Jeremy D; Walker, Aaron K

2009-11-15

A dynamic leaching test (DLT) was developed and used to evaluate the leaching of toxic substances for electronic waste in the environment. The major components in personal computers (PCs) including motherboards, hard disc drives, floppy disc drives, and compact disc drives were tested. The tests lasted for 2 years for motherboards and 1.5 year for the disc drives. The extraction fluids for the standard toxicity characteristic leaching procedure (TCLP) and synthetic precipitation leaching procedure (SPLP) were used as the DLT leaching solutions. A total of 18 elements including Ag, Al, As, Au, Ba, Be, Cd, Cr, Cu, Fe, Ga, Ni, Pd, Pb, Sb, Se, Sn, and Zn were analyzed in the DLT leachates. Only Al, Cu, Fe, Ni, Pb, and Zn were commonly found in the DLT leachates of the PC components. Their leaching levels were much higher in TCLP extraction fluid than in SPLP extraction fluid. The toxic heavy metal Pb was found to continuously leach out of the components over the entire test periods. The cumulative amounts of Pb leached out of the motherboards in TCLP extraction fluid reached 2.0 g per motherboard over the 2-year test period, and that in SPLP extraction fluid were 75-90% less. The leaching rates or levels of Pb were largely affected by the content of galvanized steel in the PC components. The higher was the steel content, the lower the Pb leaching rate would be. The findings suggest that the obsolete PCs disposed of in landfills or discarded in the environment continuously release Pb for years when subjected to landfill leachate or rains.

Accelerated Leach Test(s) Program. Annual report

International Nuclear Information System (INIS)

Dougherty, D.R.; Fuhrmann, M.; Colombo, P.

1985-09-01

This report summarizes the work performed for the Accelerated Leach Test(s) Program at Brookhaven National Laboratory in Fiscal Year 1985 under the sponsorship of the US Department of Energy's Low-Level Waste Management Program (LLWMP). Programmatic activities were concentrated in three areas, as listed and described in the following paragraphs. (1) A literature survey of reported leaching mechanisms, available mathematical models and factors that affect leaching of LLW forms has been compiled. Mechanisms which have been identified include diffusion, dissolution, ion exchange, corrosion and surface effects. Available mathematical models are based on diffusion as the predominant mechanism. Although numerous factors that affect leaching have been identified, they have been conveniently categorized as factors related to the entire leaching system, to the leachant or to the waste form. A report has been published on the results of this literature survey. (2) A computerized data base of LLW leaching data and mathematical models is being developed. The data are being used for model evaluation by curve fitting and statistical analysis according to standard procedures of statistical quality control. (3) Long-term tests on portland cement, bitumen and vinyl ester-styrene (VES) polymer waste forms are underway which are designed to identify and evaluate factors that accelerate leaching without changing the mechanisms. Results on the effect of temperature on leachability indicate that the leach rates of cement and VES waste forms increase with increasing temperature, whereas, the leach rate of bitumen is little affected

Long-term leaching behavior of vitrified high-level wastes

International Nuclear Information System (INIS)

Ishiguro, Katsuhiko; Sonobe, Hitoshi; Sasaki, Noriaki; Kashihara, Hidechiyo

1985-01-01

A long-term Soxhlet leaching test, long-term static leaching test, solubility evaluation test and actual-scale glass solid leaching test were carried out for simulated vitrified wastes. Under high flow-rate leachate conditions, the leaching of high-solubility substances such as B and Na increases almost linearly with time while that of Fe, Ni and rare earth metals strongly depends on their solubility. The overall leaching rate changes (tends to decrease) with time under static conditions. The elution or diffusion is the rate determining step in the earlier region of the leaching process while the solubilities of major components have greater effects in the latter region. The change of the dominant leaching mechanism is delayed more largely as the surface-area to leachate-volume (SA/V) ratio decreases. Actual-scale glass specimens showed almost the same leaching behaviors as small-scale ones. If cracks exist in glass solid, the leaching in them is slow causing little effects on the overall leaching rate. This may be due to the fact that solubility-dependent leaching is occuring in the cracks. The long-term static leaching observations were not satisfactorily explained by the MCC-3 type solubility test results. It is important to clarify the solubility-dependent leaching behaviors at large SA/V ratios. (Nogami, K.)

Characterization and Leach Testing for REDOX Sludge and S-Saltcake Actual Waste Sample Composites

International Nuclear Information System (INIS)

Fiskum, Sandra K.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Hubler, Timothy L.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; Lumetta, Gregg J.; MacFarlan, Paul J.; McNamara, Bruce K.; Peterson, Reid A.; Sinkov, Sergey I.; Snow, Lanee A.; Swoboda, Robert G.

2008-01-01

This report describes processing and analysis results of boehmite waste type (Group 5) and insoluble high Cr waste type (Group 6). The sample selection, compositing, subdivision, physical and chemical characterization are described. Extensive batch leach testing was conducted to define kinetics and leach factors of selected analytes as functions of NaOH concentration and temperature. Testing supports issue M-12 resolution for the Waste Treatment Plant

Characterization and Leach Testing for REDOX Sludge and S-Saltcake Actual Waste Sample Composites

Energy Technology Data Exchange (ETDEWEB)

Fiskum, Sandra K.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Hubler, Timothy L.; Jagoda, Lynette K.; Jenson, Evan D.; Kozelisky, Anne E.; Lumetta, Gregg J.; MacFarlan, Paul J.; McNamara, Bruce K.; Peterson, Reid A.; Sinkov, Sergey I.; Snow, Lanee A.; Swoboda, Robert G.

2008-07-10

This report describes processing and analysis results of boehmite waste type (Group 5) and insoluble high Cr waste type (Group 6). The sample selection, compositing, subdivision, physical and chemical characterization are described. Extensive batch leach testing was conducted to define kinetics and leach factors of selected analytes as functions of NaOH concentration and temperature. Testing supports issue M-12 resolution for the Waste Treatment Plant.

Mechanism for elevated temperature leaching

International Nuclear Information System (INIS)

Kenna, B.T.; Murphy, K.D.

1979-01-01

Long-term, elevated temperature leaching and subsequent electron microprobe analysis of simulated waste glass and ceramic materials have been completed. A cyclic leaching pattern was found in all systems over a 20-month period. It appears that the leaching of mobile ions by simple diffusional processes is modified by more complex chemical interactions. The release of immobile ions is primarily a function of their chemical interactions in the matrix which suggests that these ions may be complex species when released into solution. A mechanism is proposed which incorporates these ideas and the cyclic phenomenon observed

77 FR 22609 - Notice of Intent To Prepare an Environmental Impact Statement for the Proposed Pan Mine Project...

Science.gov (United States)

2012-04-16

... business hours. SUPPLEMENTARY INFORMATION: Midway Gold US Inc. (Midway) proposes to construct and operate an open-pit gold mining operation, which would include open pits, a heap leach pad, waste rock dumps, and ancillary facilities. The mine would be located in the northern part of the Pancake Mountain Range...

Understanding Lateritic Ore Agglomeration Behaviour as a ...

African Journals Online (AJOL)

Processing such ores through cost-competitive heap (4-10 m high) leaching as an alternative, requires successful agglomeration of the feed into robust and porous granules. To date, produc-ing of granules with desirable attributes poses a major geotechnical challenge to industry. In the present work, we investigate ...

Acid mine drainage simulated leaching behavior of goethite and cobalt substituted goethite

Science.gov (United States)

Penprase, S. B.; Kimball, B. E.

2015-12-01

Though most modern day mining aims to eliminate the seepage of acid mine drainage (AMD) to the local watershed, historical mines regularly receive little to no remediation, and often release acidic, metal-rich drainage and particles to the environment. Treatment of AMD often includes neutralizing pH to facilitate the precipitation of Fe-oxides and dissolved trace metals, thereby forming Trace Metal Substituted (TMS) forms of known minerals, such as goethite (α-FeOOH). The stability of TMS precipitates is not fully understood. As a result, we conducted a 20 day leach experiment using laboratory synthesized pure (Gt) and cobalt-substituted (CoGt) goethites with a dilute ultrapure HCl solution (pH = 3.61) at T = 23.3±2.5ºC. Leached solids were characterized using X-ray diffraction (XRD) and scanning electron microscopy paired with energy dispersive spectroscopy (SEM-EDS). Leach solutions were sampled for pH and conductivity, and dissolved chemistry was determined with Inductively Coupled Plasma Mass Spectroscopy (ICP-MS). Preliminary results indicate Gt and CoGt filtered leach solutions experienced constant pH (Gt = 3.9 ± 0.1, CoGt = 6.8 ± 0.2) and conductivity (Gt = 69 ± 6.6 μS/cm, CoGt = 81 ± 16 μS/cm) for t = 0-20 days. Micro-focused XRD results indicate that leached solids did not change in mineralogy throughout the experiment, and SEM images show minor disintegration along mineral grain edges, but little overall change in shape. Preliminary ICP-MS results show lower dissolved Fe concentrations for CoGt (1.1 ± 1.1 ppb) compared to Gt (17 ± 8.9 ppb) over time. Dissolved Co concentrations ranged from 560 - 830 ppb and increased over time. Compared to leaching of pure Gt, leaching of CoGt generated significantly higher pH, slightly higher conductivity, and significantly less dissolved Fe. During the CoGt leach, Co was preferentially leached over Fe. The differences in leaching behavior between pure and TMS goethite in the laboratory have implications for

Effect of organic amendments on nitrate leaching mitigation in a sandy loam soil of Shkodra district, Albania

Directory of Open Access Journals (Sweden)

Erdona Demiraj

2018-03-01

Full Text Available European lacustrine systems are frequently exposed to nitrate (NO3– pollution causing eutrophication processes. An example of these lakes is Shkodra Lake, a large, shallow lake shared by Albania and Montenegro, in the Balkans Peninsula. Shkodra Lake is a natural sink that collects NO3– from agricultural activities, widely diffused in the surrounding area. The additions of wheat straw and biochar have been suggested to increase soil NO3– retention of agricultural lands. To better understand the role of these two organic soil amendments in mitigating NO3– leaching from arable lands, a pot experiment using a representative sandy loam soil of the Skodra Lake basin was performed. More specifically, a greenhouse experiment with Lolium multiflorum L. and Zea mays L., was carried out for three months, to evaluate the concentrations of NO3–-N in leachate and the cumulative leaching losses of NO3–-N, after wheat straw (10 Mg ha–1 and biochar (10 Mg ha–1 soil addition, under the same rate of NPK fertiliser (300 kg ha–1. The effect of the two organic amendments on nitrate retention, was evaluated according to two methods: i Soil NO3–-N leaching with distilled water; and ii Soil NO3–-N extraction with 2M KCl. The leached NO3–-N and the Potentially Leachable NO3–-N (2M KCl extraction were respectively determined. N uptake by plants, as well as the Nitrogen Use Efficiency were also calculated. A retention effect on nitrate was found in Lolium multiflorum L. and wheat straw treatments compared to control, by reducing leached NO3–-N almost to 35%. In SBFL (soil+biochar+fertiliser+Lolium treatment, biochar effectively reduced the total amount of nitrate in leachate of 27% and 26% compared to SFL (soil+fertiliser+Lolium and SSFL (soil+straw+fertiliser+Lolium treatments, respectively. The potentially leachable NO3–-N was two to four times higher than the leached NO3–-N. The amount of potentially leachable NO3–-N per hectare ranged

Deep cleaning of a metallurgical zinc leaching residue and recovery of valuable metals

Science.gov (United States)

Xing, Peng; Ma, Bao-zhong; Zeng, Peng; Wang, Cheng-yan; Wang, Ling; Zhang, Yong-lu; Chen, Yong-qiang; Wang, Shuo; Wang, Qiu-yin

2017-11-01

Huge quantities of zinc leaching residues (ZLRs) generated from zinc production are dumped continuously around the world and pose a potential environmental threat because of their considerable amounts of entrained heavy metals (mainly lead). Most ZLRs have not been properly treated and the valuable metals in them have not yet been effectively recovered. Herein, the deep cleaning of a ZLR and recovery of valuable metals via a hydrometallurgical route were investigated. The cleaning process consists of two essential stages: acid leaching followed by calcium chloride leaching. The optimum conditions for extracting zinc, copper, and indium by acid leaching were a sulfuric acid concentration of 200 g·L-1, a liquid/solid ratio of 4:1 (mL/g), a leaching time of 2 h, and a temperature of 90°C. For lead and silver extractions, the optimum conditions were a calcium chloride concentration of 400 g·L-1, a pH value of 1.0, a leaching time of 1 h, and a temperature of 30°C. After calcium chloride leaching, silver and lead were extracted out and the lead was finally recovered as electrolytic lead by electrowinning. The anglesite phase, which poses the greatest potential environmental hazard, was removed from the ZLR after deep cleaning, thus reducing the cost of environmental management of ZLRs. The treatment of chlorine and spent electrolyte generated in the process was discussed.

Arsenic-containing soil from geogenic source in Hong Kong: Leaching characteristics and stabilization/solidification.

Science.gov (United States)

Li, Jiang-Shan; Beiyuan, Jingzi; Tsang, Daniel C W; Wang, Lei; Poon, Chi Sun; Li, Xiang-Dong; Fendorf, Scott

2017-09-01

Geogenic sources of arsenic (As) have aroused extensive environmental concerns in many countries. This study evaluated the vertical profiles, leaching characteristics, and surface characteristics of As-containing soils in Hong Kong. The results indicated that elevated levels of As (486-1985 mg kg -1 ) were mostly encountered in deeper layer (15-20 m below ground). Despite high concentrations, geogenic As displayed a high degree of chemical stability in the natural geochemical conditions, and there was minimal leaching of As in various leaching tests representing leachability, mobility, phytoavailability, and bioaccessibility. Microscopic/spectroscopic investigations suggested that As in the soils was predominantly present as As(V) in a coordination environment with Fe oxides. Sequential extraction indicated that the majority of As were strongly bound with crystalline Fe/Al oxides and residual phase. Yet, uncertainties may remain with potential As exposure through accidental ingestion and abiotic/biotic transformation due to changes in geochemical conditions. Hence, the effectiveness of stabilization/solidification (S/S) treatment was evaluated. Although the leached concentrations of As from the S/S treated soils increased to varying extent in different batch leaching tests due to the increase in alkalinity, the mobility of As was considered very low based on semi-dynamic leaching test. This suggested that As immobilization in the S/S treated soils was predominantly dependent on physical encapsulation by interlocking framework of hydration products, which could also prevent potential exposure and allow controlled utilization of S/S treated soils as monolithic materials. These results illustrate the importance of holistic assessment and treatment/management of As-containing soils for enabling flexible future land use. Copyright © 2017 Elsevier Ltd. All rights reserved.

Leaching from municipal solid waste incineration residues

Energy Technology Data Exchange (ETDEWEB)

Hyks, J.

2008-02-15

Leaching of pollutants from Municipal Solid Waste Incineration (MSWI) residues has been investigated combining a range of laboratory leaching experiments with geochemical modeling. Special attention was paid to assessing the applicability of laboratory data for subsequent modeling with respect to presumed full-scale conditions; both sample pretreatment and actual influence of leaching conditions on the results of laboratory experiments were considered. It was shown that sample pretreatment may have large impact on leaching test data. In particular, a significant fraction of Pb was shown mobile during the washing of residues with water. In addition, drying of residues (i.e. slow oxidation) prior to leaching experiments increased the leaching of Cr significantly. Significant differences regarding the leaching behavior of individual elements with respect to (non)equilibrium conditions in column percolation experiments were observed in the study. As a result, three groups of elements were identified based on the predominant leaching control and the influence of (non)equilibrium on the results of the laboratory column experiments: I. Predominantly availability-controlled elements (e.g. Na, K, Cl) II. Solubility-controlled elements (e.g. Ca, S, Si, Al, Ba, and Zn) III. Complexation-controlled elements (e.g. Cu and Ni) With respect to the above groups it was suggested that results of laboratory column experiments can, with consideration, be used to estimate full-scale leaching of elements from Group I and II. However, in order to avoid large underestimations in the assessment of leaching from Group III, it is imperative to describe the time-dependent transport of dissolved organic carbon (DOC) in the tested system or to minimize the physical non-equilibrium during laboratory experiments (e.g. bigger column, slower flow velocity). Forward geochemical modeling was applied to simulate long-term release of elements from a MSWI air-pollution-control residue. Leaching of a

Long-term leach rates of glasses containing actual waste

International Nuclear Information System (INIS)

Wiley, J.R.; LeRoy, J.H.

1979-01-01

Leach rates of borosilicate glasses that contained actual Savannah River Plant waste were measured. Leaching was done by water and by buffer solutions of pH 4, 7, and 9. Leach rates were then determined from the amount of 137 Cs, 90 Sr, and Pu released into the leach solutions. The cumulative fractions leached were fit to a mathematical model that included leaching by diffusion and glass dissolution

Chlorine-assisted leaching of Key Lake uranium ore

International Nuclear Information System (INIS)

Haque, K.E.

1981-04-01

Bench-scale chlorine-assisted leach tests were conducted on the Key Lake uranium ore. Leach tests conducted at 80 0 C on a slurry containing 50% solids during 10 hours of agitation gave the maximum extraction of uranium - 96% and radium-226 - 91%. Chlorine was added at 23.0 Kg Cl 2 /tonne of ore to maintain the leach slurry pH in the range of 1.5-1.0. To obtain residue almost free of radionuclides, hydrochloric acid leaches were conducted on the first stage leach residues. The second stage leach residue still was found to contain uranium - 0.0076% and radium-226 - 200 pCi/g of solids

Implementation of the Leaching Environmental Assessment Framework

Science.gov (United States)

New leaching tests are available in the U.S. for developing more accurate source terms for use in fate and transport models. For beneficial use or disposal, the use of the leaching environmental assessment framework (LEAF) will provide leaching results that reflect field condit...

Optimizing conditions for an accelerated leach test

International Nuclear Information System (INIS)

Pietrzak, R.F.; Fuhrmann, M.; Heiser, J.; Franz, E.M.; Colombo, P.

1988-01-01

An accelerated leach test for low-level radioactive waste forms is being developed to provide, in a short time, data that can be extrapolated to long time periods. The approach is to provide experimental conditions that will accelerate leaching without changing the dominant release mechanism. Experimental efforts have focused on combining individual factors that have been observed to accelerate leaching. These include elevated temperature, increased leachant volume, and reduced specimen size. The response of diffusion coefficients to various acceleration factors have been evaluated and provide information on experimental parameters that need to be optimized to increase leach rates. Preliminary modeling using a diffusion mechanism (allowing for depletion) of a finite cylinder geometry indicates that during early portions of experiments (daily sampling intervals), leaching is diffusion controlled and more rapid than later in the same experiments (weekly or greater sampling intervals). For cement waste forms, this reduction in rate may be partially controlled by changes in physical structure and chemistry (sometimes related to environmental influences such as CO 2 ), but it is more likely associated with the duration of the sampling interval. By using a combination of mathematical modeling and by experimentally investigating various leach rate controlling factors, a more complete understanding of leaching processes is being developed. This, in turn, is leading to optimized accelerating conditions for a leach test

Long-term leach rates of glasses containing actual waste

International Nuclear Information System (INIS)

Wiley, J.R.; LeRoy, J.H.

1979-01-01

Leach rates of borosilicate glasses that contained actual Savannah River Plant waste were measured. Leaching was done by water and by buffer solutions of pH 4, 7, and 9. Leach rates were then determined from the amount of 137 Cs, 90 Sr, and plutonium released into the leach solutions. The cumulative fractions leached were fit to a mathematical model that included leaching by diffusion and glass dissolution. 5 figures, 3 tables

A Mineralogical Assessment on Residues after Acidic Leaching of Bauxite Residue (Red Mud for Titanium Recovery

Directory of Open Access Journals (Sweden)

Gözde Alkan

2017-10-01

Full Text Available Due to its alkalinity, red mud produced by the Bayer process may affect both the environment and human health. For this reason, its further utilization instead of disposal is of great importance. Numerous methods have already been studied for hydrometallurgical treatment of red mud, especially for the recovery of various metallic components such as iron, aluminum, titanium or rare earth elements. This study focuses on the extraction of titanium from red mud and in particular the mineralogical changes, induced by leaching. Sulfuric acid, hydrochloric acid and their combination have been utilized as leaching agents with the same leaching parameters. It has been determined that sulfuric acid is the best candidate for the red mud treatment in terms of titanium leaching efficiency at the end of 2 h with a value of 67.3%. Moreover, samples from intermediate times of reaction revealed that leaching of Ti exhibit various reaction rates at different times of reaction depending on acid type. In order to explain differences, X-ray Diffraction (XRD, scanning electron microscope (SEM and QEMSCAN techniques were utilized. Beside titanium oxide (TiO2 with available free surface area, a certain amount of the TiO2 was detected as entrapped in Fe dominating oxide. These associations between Ti and Fe phases were used to explain different leaching reaction rates and a reaction mechanism was proposed to open a process window.

Leaching methods for conditioned radioactive waste

International Nuclear Information System (INIS)

Carpentiero, R.; Bienvenu, P.; Huebra, A. G. de la; Dale, C.; Grec, D.; Gallego, C.; Rodriguez, M.; Vanderlinden, F.; Voors, P. I.; Welbergen, J.; May, R.; Fays, J.

2005-01-01

The physico-chemical characterization of solidified, real or simulated, radioactive waste is essential in determining their long-term stability in conditions close to that which could be encountered during disposal. The evaluation or prediction of the performance of conditioned waste passes through many suitable studies and experiments, according to a documented qualification programme. In this respect the leaching test is among the first important techniques to evaluate the feasibility of a waste form and for comparing and selecting the best waste form. So the leaching behaviour of an immobilized radioactive waste is a relevant property to be studied. The objective of the present report is to collect and describe the most representative leaching methods used in international laboratories, mainly at European level, whether standard or standard-derived. In this instance the work is a summary of the Network knowledge and applications on leaching processes in order to exchange information and scientific and technical experiences in this respect. The focus is to express all the relevant parameters of the test and its field of application. all this background is the needed starting point to clarify the similarities and shortcomings of the methods used in the EN-TRAP laboratories and, subsequently, the possible equalities or differences which can be attributed to the characteristic parameters of the different type of wastes treated. In order to comprise the significance and the effects of the parameters involved in leaching phenomena, an initial discussion on leaching mechanisms and on achievable results is made in this document. The international standardised methods are summarised as being the origin for all the network leaching procedures. This work in a preliminary way represents a comparative review ordered to introduce an unique leaching procedure to be tested in an interlaboratory comparative exercise. Further the unique method would be a quick internal reference

The enhancing of Au-Ag-Te content in tellurium-bearing ore mineral by bio-oxidation-leaching

Science.gov (United States)

Kim, PyeongMan; Kim, HyunSoo; Myung, EunJi; Kim, YoonJung; Lee, YongBum; Park*, CheonYoung

2015-04-01

The purpose of this study is to enhance the content of valuable metals such as Au-Ag-Te in tellurium-bearing minerals by bio-oxidation-leaching. It was confirmed that pyrite, chalcopyrite, sphalerite and galena were produced together with tellurium-bearing minerals including hessite, sylvanite and tellurobismuthite from ore minerals and concentrates through microscopic observation and SEM/EDS analysis. In a bio-oxidation-leaching experiment, with regard to Au, Ag, Te, Cu and Fe, the changes in the amount of leaching and the content of leaching residues were compared and analyzed with each other depending on the adaptation of an indigenous microbe identified as Acidithiobacillus ferrooxidans. As a result of the experiment, the Au-Ag-Te content in tellurium-bearing ore mineral was enhanced in the order of physical oxidation leaching, physical/non-adaptive bio-oxidation-leaching and physical/adaptive biological leaching. It suggests that the bio-oxidation-leaching using microbes adapted in tellurium-bearing ore mineral can be used as a pre-treatment and a main process in a recovery process of valuable metals. "This research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education(NRF-2013R1A1A2004898)"

Evaluation of the leaching behavior of incineration bottom ash using seawater: A comparison with standard leaching tests.

Science.gov (United States)

Lin, Wenlin Yvonne; Heng, Kim Soon; Nguyen, Minh Quan; Ho, Jin Rui Ivan; Mohamed Noh, Omar Ahmad Bin; Zhou, Xue Dong; Liu, Alec; Ren, Fei; Wang, Jing-Yuan

2017-04-01

Batch and column tests were conducted on untreated incineration bottom ash (IBA) samples from two incineration plants in Singapore, using seawater as the leachant. The main objective of this study was to investigate the change in the leaching behavior of certain elements (i.e. As, Cd, Cr, Cu, Ni, Pb, Sb, Se and Zn) when IBA comes into contact with seawater. Such an investigation using seawater as leachant was not commonly carried out when investigating leaching behavior in IBA. The leaching tests were then carried out on the same IBA samples using DI water, as a comparison. Lower level of leaching was observed for Pb and Zn when seawater was used as the leachant. Cr and Sb showed significant cumulative release at Liquid-to-Solids (L/S) ratio 5 in the seawater column leaching. The influence of Dissolved Organic Carbon (DOC) on Cu leaching seems to decrease after L/S 2 when using seawater in the column test. Although the leaching behavior of IBA was affected when seawater was used, for the column test, there was no significant difference during the initial release when compared to DI water. The initial L/S fractions collected were important as the low L/S ratios represent the pore water concentration and the maximum output in an actual application. The results from this study would be useful for the future study on using IBA in marine applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

Leaching behaviour of bottom ash from RDF high-temperature gasification plants

International Nuclear Information System (INIS)

Gori, M.; Pifferi, L.; Sirini, P.

2011-01-01

This study investigated the physical properties, the chemical composition and the leaching behaviour of two bottom ash (BA) samples from two different refuse derived fuel high-temperature gasification plants, as a function of particle size. The X-ray diffraction patterns showed that the materials contained large amounts of glass. This aspect was also confirmed by the results of availability and ANC leaching tests. Chemical composition indicated that Fe, Mn, Cu and Cr were the most abundant metals, with a slight enrichment in the finest fractions. Suitability of samples for inert waste landfilling and reuse was evaluated through the leaching test EN 12457-2. In one sample the concentration of all metals was below the limit set by law, while limits were exceeded for Cu, Cr and Ni in the other sample, where the finest fraction showed to give the main contribution to leaching of Cu and Ni. Preliminary results of physical and geotechnical characterisation indicated the suitability of vitrified BA for reuse in the field of civil engineering. The possible application of a size separation pre-treatment in order to improve the chemical characteristics of the materials was also discussed.

Method for accelerated leaching of solidified waste

International Nuclear Information System (INIS)

Fuhrmann, M.; Heiser, J.H.; Pietrzak, R.F.; Franz, E.M.; Colombo, P.

1990-11-01

An accelerated leach test method has been developed to determine the maximum leachability of solidified waste. The approach we have taken is to use a semi-dynamic leach test; that is, the leachant is sampled and replaced periodically. Parameters such as temperature, leachant volume, and specimen size are used to obtain releases that are accelerated relative to other standard leach tests and to the leaching of full-scale waste forms. The data obtained with this test can be used to model releases from waste forms, or to extrapolate from laboratory-scale to full-scale waste forms if diffusion is the dominant leaching mechanism. Diffusion can be confirmed as the leaching mechanism by using a computerized mathematical model for diffusion from a finite cylinder. We have written a computer program containing several models including diffusion to accompany this test. The program and a Users' Guide that gives screen-by-screen instructions on the use of the program are available from the authors. 14 refs., 4 figs., 1 tab

Leaching of copper concentrates with high arsenic content in chlorine-chloride media

International Nuclear Information System (INIS)

Herreros, O.; Fuentes, G.; Quiroz, R.; Vinals, J.

2003-01-01

This work reports the results of copper concentrates leaching which have high arsenic concepts (up to 2.5%). The treatments were carried out using chlorine that forms from sodium hypochlorite and sulphuric acid. The aim of this work is to obtain a solution having high copper content 4 to 6 g/l and 5 to 7 g/l free acid in order to submit it directly to a solvent extraction stage. In addition, this solution should have minimum content of arsenic and chloride ions. To carry out this investigation, an acrylic reactor was constructed where the leaching tests were made at constant temperature in a thermostatic bath under atmospheric pressure. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Typical variables were studied, such as leaching agent concentration, leaching time, pulp density and temperature among others. Some of the residues were analyzed by XRD and EPS. On the other hand, the solutions were analyzed by Atomic Absorption Spectroscopy. The results indicate solutions having the contents stated above can be obtained. (Author) 19 refs

The leaching kinetics of cadmium from hazardous Cu-Cd zinc plant residues.

Science.gov (United States)

Li, Meng; Zheng, Shili; Liu, Biao; Du, Hao; Dreisinger, David Bruce; Tafaghodi, Leili; Zhang, Yi

2017-07-01

A large amount of Cu-Cd zinc plant residues (CZPR) are produced from the hydrometallurgical zinc plant operations. Since these residues contain substantial amount of heavy metals including Cd, Zn and Cu, therefore, they are considered as hazardous wastes. In order to realize decontamination treatment and efficient extraction of the valuable metals from the CZPR, a comprehensive recovery process using sulfuric acid as the leaching reagent and air as the oxidizing reagent has been proposed. The effect of temperature, sulfuric acid concentration, particle size, solid/liquid ratio and stirring speed on the cadmium extraction efficiency was investigated. The leaching kinetics of cadmium was also studied. It was concluded that the cadmium leaching process was controlled by the solid film diffusion process. Moreover, the order of the reaction rate constant versus H 2 SO 4 concentration, particle size, solid/liquid ratio and stirring speed was calculated. The XRD and SEM-EDS analysis results showed that the main phases of the secondary sulfuric acid leaching residues were lead sulfate and calcium sulfate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Continuous-flow leaching studies of crushed and cored SYNROC

International Nuclear Information System (INIS)

Coles, D.G.; Bazan, F.

1982-01-01

Both crushed (150- to 300- μm) and cored (1,8- mm-diam) samples of SYNROC have been leached with single-pass continuous-flow leaching equipment. Crushed samples of cesium-hollandite were also leached in a similar experiment. Temperatures used were 25 0 and 75 0 C and leachates were 0.03 N NaHCO 3 and distilled water. Leaching rates from SYNROC-C were ranked cesium > strontium greater than or equal to calcium > barium > zirconium. A comparison of leaching rates is made between crushed SYNROC, cored SYNROC, and Pacific Northwest Laboratory 76-68 glass beads. This comparison depends on how the surface areas are determined for each sample. Based on geometric surface areas for SYNROC cores and glass beads, cesium leach rates from SYNROC compare well with both sodium and neptunium leached from the glass. The other elements leached from SYNROC are lower than sodium and neptunium leached from glass. They also vary for each element, while glass shows nearly the same leach rate for both sodium and neptunium

Continuous-flow leaching studies of crushed and cored SYNROC

International Nuclear Information System (INIS)

Coles, D.G.; Bazan, F.

1981-01-01

Both crushed (150 to 300 μm) and cored (1.8 mm diameter) samples of SYNROC have been leached with the single-pass continuous-flow leaching equipment. Crushed samples of Cs-hollandite were also leached in a similar experiment. Temperatures used were 25 and 75 0 C and leachates were 0.03 N NaHCO 3 and distilled water. Leaching rates from SYNROC C were ranked Cs > Sr greater than or equal to Ca > Ba > Zr. A comparison of leaching rates is made between crushed SYNROC, cored SYNROC, and PNL 76-68 glass beads. This comparison depends on how the surface areas are determined for each sample. Based on geometric surface areas for SYNROC cores and glass beads Cs leach rates from SYNROC compare well with both Na and Np leached from the glass. The other elements leached from SYNROC are lower than Na and Np leached from glass. They also vary for each element while glass shows nearly the same leach rate for both Na and Np

Main trends in scientific-research works during construction and operation of uranium mines and open cuts

International Nuclear Information System (INIS)

Mosinets, V.N.

1993-01-01

Consideration is given to main trends in research works during construction and operation of uranium mines and open cuts of Priargunsky mine-chemical association. Develops and introduced principally new design solutions and technologies in the field of open mining, underground mining, as well as in-situ and heap leaching, are described

A device for uranium series leaching from glass fiber in HEPA filter

International Nuclear Information System (INIS)

Gye-Nam Kim; Hye-Min Park; Wang-Kyu Choi; Jei-Kwon Moon

2012-01-01

For the disposal of a high efficiency particulate air (HEPA) glass filter into the environment, the glass fiber should be leached to lower its radioactive concentration to the clearance level. To derive an optimum method for the removal of uranium series from a HEPA glass fiber, five methods were applied in this study. That is, chemical leaching by a 4.0 M HNO 3 -0.1 M Ce(IV) solution, chemical leaching by a 5 wt% NaOH solution, chemical leaching by a 0.5 M H 2 O 2 -1.0 M Na 2 CO 3 solution, chemical consecutive chemical leaching by a 4.0 M HNO 3 solution, and repeated chemical leaching by a 4.0 M HNO 3 solution were used to remove the uranium series. The residual radioactivity concentrations of 238 U, 235 U, 226 Ra, and 234 Th in glass after leaching for 5 h by the 4.0 M HNO 3 -0.1 M Ce(IV) solution were 2.1, 0.3, 1.1, and 1.2 Bq/g. The residual radioactivity concentrations of 238 U, 235 U, 226 Ra, and 234 Th in glass after leaching for 36 h by 4.0 M HNO 3 -0.1 M Ce(IV) solution were 76.9, 3.4, 63.7, and 71.9 Bq/g. The residual radioactivity concentrations of 238 U, 235 U, 226 Ra, and 234 Th in glass after leaching for 8 h by a 0.5 M H 2 O 2 -1.0 M Na 2 CO 3 solution were 8.9, 0.0, 1.91, and 6.4 Bq/g. The residual radioactivity concentrations of 238 U, 235 U, 226 Ra, and 234 Th in glass after consecutive leaching for 8 h by the 4.0 M HNO 3 solution were 2.08, 0.12, 1.55, and 2.0 Bq/g. The residual radioactivity concentrations of 238 U, 235 U, 226 Ra, and 234 Th in glass after three repetitions of leaching for 3 h by the 4.0 M HNO 3 solution were 0.02, 0.02, 0.29, and 0.26 Bq/g. Meanwhile, the removal efficiencies of 238 U, 235 U, 226 Ra, and 234 Th from the waste solution after its precipitation-filtration treatment with NaOH and alum for reuse of the 4.0 M HNO 3 waste solution were 100, 100, 93.3, and 100%. (author)

Optimizing conditions for an accelerated leach test

International Nuclear Information System (INIS)

Pietrzak, R.F.; Fuhrmann, M.; Heiser, J.; Franz, E.M.; Colombo, P.

1988-01-01

An accelerated leach test for low-level radioactive waste forms is being developed to provide, in a short time, data that can be extrapolated to long time periods. The approach is to provide experimental conditions that will accelerate leaching without changing the dominant release mechanism. Experimental efforts have focused on combining individual factors that have been observed to accelerate leaching. These include elevated temperature, increased leachant volume, and reduced specimen size. The response of diffusion coefficients to various acceleration factors have been evaluated and provide information on experimental parameters that need to be optimized to increase leach rates. For example, these data show that large volumes of leachant are required when leaching portland cement waste forms at elevated temperatures because of high concentrations of dissolved species. Sr-85 leaching is particularly susceptible to suppression due to concentration effects while Cs-137 leaching is less so. Preliminary modeling using a diffusion mechanism (allowing for depletion) of a finite cylinder geometry indicates that during early portions of experiments (daily sampling intervals), leaching is diffusion controlled and more rapid than later in the same experiments (weekly or greater sampling intervals). For cement waste forms, this reduction in rate may be partially controlled by changes in physical structure and chemistry (sometimes related to environmental influences such as CO 2 ), but it is more likely associated with the duration of the sampling interval. 9 refs., 6 figs

Leach-SX-EW copper revalorization from overburden of abandoned copper mine Cerovo, Eastern Serbia

Directory of Open Access Journals (Sweden)

Stevanović Z.

2009-01-01

Full Text Available Hydrometallurgical processes for copper revalorization from overburden of abandoned mine Cerovo in Eastern Serbia were studied. Paper contain results of percolation leaching tests, performed with acidic mine waters accumulated in the bottom of the former open pit, followed by solvent extraction (SX and electrowinning (EW processes on achieved copper pregnant leach solutions. Usage of accumulated waste waters was objected to minimizing the environmental hazard due to uncontrolled leaking of these waters in nearby creeks and rivers. Chemical composition of acidic mine waters used for leaching tests was: (g/dm3: Cu - 0.201; Fe - 0.095; Mn - 0.041; Zn - 0.026; Ni - 0.0004; pH value - 3.3. Copper content in overburden sample used for leaching tests was 0.21% from which 64% were oxide copper minerals. In scope of leaching tests were examined influence of leaching solution pH values and iron (III concentration on copper recovery. It was established that for 120 hours of leaching on pH=1.5 without oxidant agents, copper concentration in pregnant leach solutions enriched up to 1.08g/dm3 which was enough for copper extraction from solution with SX-EW treatment. As extraction reagent in SX circuit was used LIX-984N in a kerosene diluent. Cathode current density in electrowinning cell was 220Am-2 while electrolyte temperature was kept on 50±2oC. Produced cathode copper at the end of SX-EW process has purity of 99.95% Cu.

Single-pass continuous-flow leach test of PNL 76-68 glass: some selected Bead Leach I results

International Nuclear Information System (INIS)

Coles, D.G.

1981-01-01

A single-pass continuous-flow leach test of PNL 76-68 glass beads (7 mm dia) was concluded after 420 days of uninterrupted operation. Variables included in the experimental matrix were flow-rate, leachant composition, and temperature. Analysis was conducted on all leachate samples for 237 Np and 239 Pu as well as a number of nonradioactive elements. Results indicated that flow-rate and leachant systematically affected the leach rate, but only slightly. Temperature effects were significant. Plutonium leach rate was lower at higher temperature suggesting that Pu sorption onto the beads was enhanced at the higher temperature. The range of leach rates for all analyzed elements (except Pu), at both temperature, at all three flow rates, and with all three leachant compositions varied only three orders of magnitude. The range of variables used in this experiment covered those expected in many proposed repository environments. The preliminary interpretation of the results also indicated that matrix dissolution may be the dominant leaching mechanism, at least for Np in bicarbonate leachant. Regardless of the leaching mechanism the importance of this study is that it bounds the effects of repository environments when the ground water is oxidizing and when it doesn't reach the waste form until the waste has cooled to ambient rock temperature

The use of biochar to reduce nitrogen and potassium leaching from soil cultivated with maize

Directory of Open Access Journals (Sweden)

W Widowati

2014-10-01

Full Text Available Nutrient leaching is often a problem especially in tropical areas with soil fertility constraints. This study aims to reveal the effect of biochars on leaching and uptake of nitrogen and potassium from degraded soils cultivated with maize. Each of three types of biochar originated from rice husk, wood, and coconut shell, was applied to the soil placed in PVC tube at four rates (0, 15, 30, and 45 t/ha. Maize was then planted in each pot. All pots received urea (135 kg N/ha, SP36 (36 kg P2O5/ha, and KCl (110 kg K2O/ha. Twelve treatments (three biochars and four application rates were arranged in a factorial randomized block design with three replicates. Results of the study showed interaction effects of biochar materials and biochar rates on nitrate leaching (except on day 1 to 30 and potassium, N uptake, and plant growth. On day 1-30, leaching of nitrate and potassium was reduced by biochar application. The lowest nitrate leaching was observed at rate of 45 t /ha of wood biochar, while application of 45 t coconut shell biochar / ha resulted in the highest K leaching. Beside, wood biochar resulted in a similar nitrate leaching with that of coconut shell biochar, but nitrate leaching increased with increasing rate of rice husk biochar on day 30-60. All biochar materials yielded similar potassium leaching at all rates. Application of 45 t rice husk biochar /ha resulted in the best maize growth.

Leaching studies on SYNROC at 950C and 2000C

International Nuclear Information System (INIS)

Oversby, V.M.; Ringwood, A.E.

1982-01-01

Crushed samples of SYNROC containing 9%, 16% and 20% of simulated high-level nuclear waste were tested for leaching behavior in distilled water at 95 0 C and 200 0 . Leach solutions were analyzed for Cs, Ca, Ba, Sr, Ti, Zr, Nd and U. Results showed that leach rates based on these elements did not change significantly as the waste loading was increased from 9 to 20%. At both temperatures, leach rates showed a decrease as leaching progressed until a plateau level was reached. Plateau leach rates, which were between 10 and 100 times lower than initial leach rates, reflect the expected long term leaching behaviour of the samples. Plateau values of leach rates for SYNROC depend on the element being leached. Highest values are found for Cs and Ba (1 to 2 x 10 -7 g/cm 2 d at 95 0 C) and lowest values for U (5 x 10 -10 g/cm 2 d at 95 0 C). Increasing leaching temperature to 200 0 C produces higher leach rates for all elements except Nd. Comparison of SYNROC leach rate data with that for PNL 76-68 glass shows that at 200 0 C the leach rate for U from SYNROC is 3000 times less than that from glass. (Auth.)

Alternative leaching processes for uranium ores

International Nuclear Information System (INIS)

Ring, R.J.

1979-01-01

Laboratory studies have been carried out to compare the extraction of uranium from Australian ores by conventional leaching in sulphuric acid with that obtained using hydrochloric acid and acidified ferric sulphate solutions. Leaching with hydrochloric acid achieved higher extractions of radium-226 but the extraction of uranium was reduced considerably. The use of acidified ferric sulphate solution reduced acid consumption by 20-40% without any detrimental effect on uranium extraction. The ferric ion, which is reduced during leaching, can be reoxidized and recycled after the addition of acid makeup. Hydrogen peroxide was found to be an effective oxidant in conventional sulphuric acid leaching. It is more expensive than alternative oxidants, but it is non-polluting, lesser quantities are required and acid consumption is reduced

Leaching behaviour of strontium-90 in cement composites

International Nuclear Information System (INIS)

Matsuzuru, H.; Ito, A.

1977-01-01

The leaching of 90 Sr from a cement composite into an aqueous phase has been studied by the method recommended by IAEA. The amount leached was measured as functions of waste to cement ratio (Wa/C), salt content of waste, temperature of leachant and curing time of specimens. The leach coefficient of 90 Sr varies from ca. 6 x 10 -8 to 4 x 10 -7 cm 2 /day depending on the composition of specimen and the leaching conditions. The leachability depends on such factors as Wa/C, temperature of leachant and curing time. The Portland cement composite gives a higher leaching fraction than the slag cement one. Additives used have no significant effect on the leachability. The amount leached in deionized water as a leachant is higher than in synthetic sea water. On the basis of the results obtained, the amount of 90 Sr leached from a composite of 200 1 drum size for an extended period was estimated. (author)

Aqueous-chlorine leaching of typical Canadian uranium ores

International Nuclear Information System (INIS)

Haque, K.E.

1982-01-01

Laboratory-scale aqueous-chlorine leaches were conducted on quartz-pebble conglomerates, pegmatite and vein-type ores. Optimum leach temperatures, pulp density and retention times were determined. Uranium extraction of 98 per cent was obtained from the Elliot Lake, Madawaska Mines of Bancroft and Rabbit Lake ores, 96 per cent from the Key Lake ore and 86 per cent from the Agnew Lake ore. However, tailings containing 15-20 pCi g -1 of radium-226 were obtained only from the Elliot Lake and Agnew lake quartz-pebble conglomerates and Bancroft pegmatite-type ores by second-stage leaches with HCl. The second-stage leach results indicate that multistage (3 or 4) acid-chloride or salt-chloride leaches might be effective to obtain tailings containing 15-20 pCi 226 Ra g -1 from the high-grade vein-type ores. Comparative reagent-cost estimates show that the sulphuric-acid leach process is far less expensive than aqueous chlorine leaching. Nevertheless, only the aqueous chlorine and acid-chloride leaches in stages are effective in producing tailings containing 15-20 pCi 226 Ra g -1 from the typical Canadian uranium ores. (Auth.)

Bacterial Leaching

Indian Academy of Sciences (India)

and studies microbial biotechnology and ... foundation for subsequent research into the role of microorgan- ... are more readily accesible, for example those in solution, rather .... Vat leaching as currently applied to oxide ores involves the.

Leaching behavior of solidified plastics radioactive wastes

International Nuclear Information System (INIS)

Yook, Chong Chul; Lee, Byung Hun; Jae, Won Mok; Kim, Kyung Eung

1986-01-01

It is highly needed to develope the solidification process to dispose safely the radioactive wastes increasing with the growth of the nuclear industry. The leaching mechanisms of the solidified plastic wastes were investigated and the leaching rates of the plastic wastes were also measured among the many solidification processes. In addition, the transport equation based on the diffusion or the diffusion-dissolution was compared with the empirical equation derived from the experimental data by graphical method. Consequently, leaching process of the solidified plastic wastes is quite well agreed with the mass transport theory, but it may be difficult to simulate leaching process by diffusion dissolution mechanism. But the theoretical equation could be applicable to the cumulative amount of radionuclides leached form the plastic wastes disposed into the environment. (Author)

Leaching of tritium from a cement composite

International Nuclear Information System (INIS)

Matsuzuru, Hideo; Ito, Akihiko

1978-10-01

Leaching of tritium from cement composites into an aqueous phase has been studied to evaluate the safety of incorporation of the tritiated liquid waste into cement. Leaching tests were performed by the method recommended by the International Atomic Energy Agency. The Leaching fraction was measured as functions of waste-cement ratio (Wa/C), temperature of leachant and curing time. The tritium leachability of cement in the long term test follows the order: alumina cement portland cement slag cement. The fraction of tritium leached increases with increasing Wa/C and temperature and decreasing curing period. A deionized water as a leachant gives a slightly higher leachability than synthetic sea water. The amount leached of tritium from a 200 l drum size specimen was estimated on the basis of the above results. (author)

Geological-economic analysis on the exploration of backup resources for depleted mines in Lujing uranium ore-field, central-southern China

International Nuclear Information System (INIS)

Li Deping; Wang Zhicheng; Fan Shaoyun

2006-01-01

With the geological-economic evaluation program for pithead heap-leaching mining uranium deposits developed by the authors and the data of column-leaching tests and the geological reserve, the geological-economic evaluation is made to the residual geological reserves of both Lujing and Huangfengling deposit, and the geological reserves of Yangjiaonao deposit of the depleted mines in Lujing uranium ore-field, central-southern China. The results of static analysis on these reserves show that the residual geological reserves of both Lujing and Huangfengling deposit belong to sub-profitable type, but the ones of Yangjiaonao deposit is profitable with 26.56% tax-before profit. 1 tU profitable type of ore from Yangjiaonao deposit can use 2.40-3.79 tU subprofitable type of ores from Lujing and Huangfengling deposit. In order to solving the problem on scarcity of backup resources of the depleted mines in Lujing uranium ore-field and using the existing sub-profitable type of geological reserves, it is suggested that the high grade of profitable type of deposits should be explored around the exhausting mines so that the production of the mines could be profitable by the pithead heap-leaching mining method with arrangement groups of both sub-profitable and profitable type of ores. (authors)

Modelling inorganic and organic biocide leaching from CBA-amine (Copper–Boron–Azole) treated wood based on characterisation leaching tests

Energy Technology Data Exchange (ETDEWEB)

Lupsea, Maria [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F–31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, DEE/Environment and Life Cycle Engineering Team, 24 Rue Joseph Fourier, F-38400 Saint Martin d' Hères (France); Tiruta-Barna, Ligia, E-mail: ligia.barna@insa-toulouse.fr [University of Toulouse, INSA, UPS, INP, LISBP, 135 Avenue de Rangueil, F–31077 Toulouse (France); INRA, UMR 792, F-31400 Toulouse (France); CNRS, UMR 5504, F-31400 Toulouse (France); Schiopu, Nicoleta [Paris-Est University, CSTB — Scientific and Technical Centre for the Building Industry, DEE/Environment and Life Cycle Engineering Team, 24 Rue Joseph Fourier, F-38400 Saint Martin d' Hères (France); Schoknecht, Ute [BAM — Federal Institute for Materials Research and Testing, Division 4.1, Unter den Eichen 87, 12205 Berlin (Germany)

2013-09-01

Numerical simulation of the leaching behaviour of treated wood is the most pertinent and less expensive method for the prediction of biocides' release in water. Few studies based on mechanistic leaching models have been carried out so far. In this work, a coupled chemistry-mass transport model is developed for simulating the leaching behaviour of inorganic (Cu, B) and organic (Tebuconazole) biocides from CBA-amine treated wood. The model is based on experimental investigations (lab-scale leaching tests coupled with chemical and structural analysis). It considers biocides' interactions with wood solid components and with extractives (literature confirmed reactions), as well as transport mechanisms (diffusion, convection) in different compartments. Simulation results helped at identifying the main fixation mechanisms, like (i) direct complexation of Cu by wood-phenolic and -carboxylic sites (and not via monoethanolamine; complex) on lignin and hemicellulose and strong dependence on extractives' nature, (ii) pH dependent binding of tebuconazole on polarized -OH moieties on wood. The role of monoethanolamine is to provide a pore-solution pH of about 7.5, when copper solubility is found to be weakest. The capability of the developed model to simulate the chemical and transport behaviour is the main result of this study. Moreover, it proved that characterization leaching tests (pH dependency and dynamic tests), combined with appropriate analytical methods are useful experimental tools. Due to its flexibility for representing and simulating various leaching conditions, chemical-transport model developed could be used to further simulate the leaching behaviour of CBA treated wood at larger scales. - Highlights: • Biocide and extractives leaching from ammonia-CBA treated wood were modelled. • The chemical-transport model identifies the main fixation/solubilisation mechanisms. • The model describes well the results of equilibrium and dynamic leaching

Armeria maritima from a calamine heap--initial studies on physiologic-metabolic adaptations to metal-enriched soil.

Science.gov (United States)

Olko, A; Abratowska, A; Zyłkowska, J; Wierzbicka, M; Tukiendorf, A

2008-02-01

Plants of Armeria maritima are found both on unpolluted sites and on soils strongly polluted with heavy metals. Seedlings of A. maritima from a zinc-lead calamine heap in ore-mining region (Bolesław population) and from unpolluted area (Manasterz population) were tested to determine the zinc, cadmium and lead tolerance. In hydroponic experiments Bolesław population was more tolerant to zinc, cadmium and lead. Localization of heavy metals in roots was determined using the histochemical method for detecting metal-complexes with dithizone. Their accumulation was found in root hairs, rhizoderma and at the surface of the central cylinder. Glutathione level in plants increased after metal treatment of both populations. However, its high level was not correlated with phytochelatin production. These metal-binding complexes were not detected in plants exposed to zinc, cadmium or lead. Changes of organic acids concentrations in Armeria treated with metals may suggest their role in metal translocation from roots to shoots. The content of organic acids, especially malate, decreased in the roots and increased in the leaves. These changes may be important in Pb-tolerance of Manasterz population and in Zn-, Cd-tolerance of calamine population from Bolesław.

Standard leach tests for nuclear waste materials

International Nuclear Information System (INIS)

Strachan, D.M.; Barnes, B.O.; Turcotte, R.P.

1980-01-01

Five leach tests were conducted to study time-dependent leaching of waste forms (glass). The first four tests include temperature as a variable and the use of three standard leachants. Three of the tests are static and two are dynamic (flow). This paper discusses the waste-form leach tests and presents some representative data. 4 figures

Long-term elevated temperature leaching of solid waste forms

International Nuclear Information System (INIS)

Kenna, B.T.; Murphy, K.D.; Levine, H.S.

1978-01-01

Long-term soxhlet leaching of simulated waste glass and ceramic materials was initiated to elucidate leaching behavior of complex wasteforms. A cyclic leaching pattern was found in all systems over a 20 month period. Maxima and minima were observed in the leaching rates of all components studied with the minima coinciding. The data suggested several mechanistic features which are described, but they did not conform with reported simple leaching mechanisms

78 FR 77706 - Notice of Intent To Prepare an Environmental Impact Statement for the Proposed Gemfield Mine...

Science.gov (United States)

2013-12-24

... gold mine and associated processing and ancillary facilities. The project would be located on public... media, newspapers and the BLM Web site at: http://www.blm.gov/nv/st/en/fo/battle_mountain_field.html... to construct, operate, reclaim, and close an open pit, heap leach, gold mining operation known as the...

Author Details

African Journals Online (AJOL)

Addai-Mensah, J. Vol 14 (2013) - Articles Understanding Lateritic Ore Agglomeration Behaviour as a Precursor to Enhanced Heap Leaching Abstract PDF. ISSN: 0855-210X. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms ...

Leaching of gallium from gaiter granite, eastern desert, Egypt

International Nuclear Information System (INIS)

Zahran, M.A.; Mahmoud, KH.F.; Mahdy, M.A.; Abd El-Hamid, A.M.

2006-01-01

Preliminary leaching tests of gallium from some Egyptian granite rocks such as those of Gabal Gattar area was investigated by using 8 M HCl acid and sodium perchlorate as oxidant. To achieve the optimum leaching conditions, the factors affecting the leaching efficiency as the acid type and concentration, oxidant type and amount, leaching temperature, agitation time, solid / liquid ratio and the effect of grain size were studied. The complete chemical analysis of the collected samples was firstly carried out to determine the chemical features of the Gattarian granite. More than 97% of gallium content was leached when applying these optimum leaching conditions

Novel Binders and Methods for Agglomeration of Ore

Energy Technology Data Exchange (ETDEWEB)

S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

2006-03-31

Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching. The active involvement of our industrial partners will help to ensure rapid commercialization of any agglomeration technologies developed by this project.

NOVEL BINDERS AND METHODS FOR AGGLOMERATION OF ORE

Energy Technology Data Exchange (ETDEWEB)

S.K. Kawatra; T.C. Eisele; J.A. Gurtler; C.A. Hardison; K. Lewandowski

2004-04-01

Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking.

Novel Binders and Methods for Agglomeration of Ore

Energy Technology Data Exchange (ETDEWEB)

S. K. Kawatra; T. C. Eisele; J. A. Gurtler; K. Lewandowski

2005-09-30

Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching. The active involvement of our industrial partners will help to ensure rapid commercialization of any agglomeration technologies developed by this project.

Measurement of leached hulls

International Nuclear Information System (INIS)

Reilly, T.D.

1979-07-01

Leached hulls are the short lengths of fuel rod cladding and fuel element hardware which constitute a major waste product of a reprocessing plant employing a chop-and-leach head-end process. The small, undissolved fuel residue (0.1 to 1.0% of original fuel content) which is discarded with this waste must be measured for safeguards, material accountability, and process control reasons. This report gives a critical analysis of hull measurement techniques involving the analysis of fission product gamma rays, spontaneous fission neutrons from curium, and delayed neutron activation. Major emphasis is given to the measurement of 2186-keV gamma rays from 144 Ce-- 144 Pr. A detailed description of typical leached hull characteristics is presented at the beginning of the report. An extensive review of experience gained from existing hull measurement systems in the United Kingdom, France, Japan, Germany, Italy, and the United States is presented

Nanosized zero-valent iron as Fenton-like reagent for ultrasonic-assisted leaching of zinc from blast furnace sludge

Energy Technology Data Exchange (ETDEWEB)

Mikhailov, Ivan, E-mail: ivan.mikhailov@misis.ru [National University of Science and Technology “MISiS”, 4 Leninskiy prospekt, Moscow, 119049 (Russian Federation); Komarov, Sergey [Tohoku University, 6-6-02 Aramaki Aza Aoba, Aoba-ku, Sendai, 980-8576 (Japan); Levina, Vera; Gusev, Alexander; Issi, Jean-Paul; Kuznetsov, Denis [National University of Science and Technology “MISiS”, 4 Leninskiy prospekt, Moscow, 119049 (Russian Federation)

2017-01-05

Highlights: • nZVI is used as Fenton-like reagent for activation of Zn leaching from the BFS. • nZVI has positive effect on kinetics of Zn leaching though with some loss of efficiency. • A complex ultrasonic-assisted method for BFS recycling is proposed. - Abstract: Ultrasonic-assisted sulphuric acid leaching combined with a Fenton-like process, utilizing nanoscale zero-valent iron (nZVI), was investigated to enhance the leaching of zinc from the blast furnace sludge (BFS). The leaching of iron (Fe) and zinc (Zn) from the sludge was investigated using Milli-Q water/BFS ratio of 10 and varying the concentration of hydrogen peroxide, sulphuric acid, the temperature, the input energy for ultrasound irradiation, and the presence or absence of nZVI as a Fenton reagent. The results showed that with 1 g/l addition of nZVI and 0.05 M of hydrogen peroxide, the kinetic rate of Zn leaching increased with a maximum dissolution degree of 80.2%, after 5 min treatment. In the absence of nZVI, the maximum dissolution degree of Zn was 99.2%, after 15 min treatment with 0.1 M of hydrogen peroxide. The rate of Zn leaching at several concentrations of hydrogen peroxide is accelerated in the presence of nZVI although a reduction in efficiency was observed. The loss of Fe was no more than 3%. On the basis of these results, the possible route for BFS recycling has been proposed (BFS slurry mixed with sulphuric acid and hydrogen peroxide is recirculated under ultrasonic irradiation then separated).

Leaching of PFC from soils contaminated with PFC of different origin

Science.gov (United States)

Kalbe, Ute; Piechotta, Christian; Rothe, Robert

2017-04-01

Leaching tests are fundamental tools for the assessment of groundwater impact by contaminated soils concerning the soil-groundwater pathway. Such procedures are supposed to serve as the basis for a reliable leachate prognosis. They can be applied to determine the short and long term leaching behaviour as well as the source term of contaminated soils. For this purpose two types of leaching procedures have been validated in Germany for the examination of the leaching behaviour of frequently occurring organic substances (DIN 19528 - column test and DIN 19529 - batch test). A liquid-to-solid ratio (L/S) of 2 L/kg and 10 L/kg) is the basis for the risk assessment which is implemented in different German regulations. The equivalence of test results for both tests for the same material under investigation has been investigated for a variety of pollutants in order to assess their reliability in compliance testing. However, for emerging pollutants there is hardly data available on this issue. Leaching tests on soils contaminated with emerging pollutants such as PFC (Perfluorinated Surfactants) are currently coming more into consideration due to the increasing detection of contaminated sites. Therefore, two soils were investigated in this study from different contamination source (paper sludge containing compost and fire distinguishing foam) using both leaching tests and both liquid-to-solid ratios. The leachability of the various perfluorinated compounds in relation to their content in solid matter was considered. Furthermore the eluate pre-treatment prior analysis (in particular liquid/solid separation step needed for batch tests) has been taken into account. The comparability of the results from batch and column is dependent on the solubility of the various compounds, on the L/S and on the turbidity in the eluates.

Development of soil microbial properties in topsoil layer during spontaneous succession in heaps after brown coal mining in relation to humus microstructure development

Czech Academy of Sciences Publication Activity Database

Frouz, Jan; Nováková, Alena

2005-01-01

Roč. 129, 1-2 (2005), s. 54-64 ISSN 0016-7061 R&D Projects: GA ČR(CZ) GA526/01/1055 Institutional research plan: CEZ:AV0Z60660521 Keywords : succession in heaps * microbial respiration * biomass Subject RIV: EH - Ecology, Behaviour Impact factor: 1.773, year: 2005

Zinc Leaching from Tire Crumb Rubber

Science.gov (United States)

Rhodes, E. P.; Ren, J.; Mays, D. C.

2010-12-01

Recent estimates indicate that more than 2 billion scrap tires are currently stockpiled in the United States and approximately 280 million more tires are added annually. Various engineering applications utilize recycled tires in the form of shredded tire crumb rubber. However, the use of tire crumb rubber may have negative environmental impacts, especially when the rubber comes into contact with water. A review of the literature indicates that leaching of zinc from tire crumb rubber is the most significant water quality concern associated with using this material. Zinc is generally used in tire manufacturing, representing approximately 1.3% of the final product by mass. This study will report results from the U.S. Environmental Protection Agency’s (EPA’s) Synthetic Precipitation Leaching Procedure, batch leaching tests, and column leaching tests performed to quantify the process by which zinc leaches from tire crumb rubber into water. Results are interpreted with a first-order kinetic attachment/detachment model, implemented with the U.S. Agricultural Research Service software HYDRUS-1D, in order to determine the circumstances when zinc leaching from tire crumb rubber would be expected to comply with the applicable discharge limits. One potential application for recycled tires is replacing sand with tire crumb rubber in granular media filters used for stormwater pollution control. For this to be a viable application, the total zinc in the stormwater discharge must be below the EPA’s benchmark value of 0.117 mg/L.

Continuous-flow leaching studies of crushed and cored SYNROC

International Nuclear Information System (INIS)

Coles, D.G.; Bazan, F.

1980-01-01

Both crushed (150 to 300 μm) and cored 1.8 mm diameter) samples of SYNROC have been leached with the single-pass continuous-flow leaching equipment. Crushed samples of Cs-hollandite were also leached in a similar experiment. Temperatures used were 25 0 C and 75 0 C and leachates were 0.03 N NaHCO 3 and distilled water. Leaching rates from SYNROC C were ranked Cs > Sr greater than or equal to Ca > Ba > Zr. A comparison of leaching rates is made between crushed SYNROC, cored SYNROC, and PNL 76-68 glass beads. Problems encountered when comparing the leaching rates of different waste forms are discussed

In-situ leach mining: the next quantum leap?

International Nuclear Information System (INIS)

Hancock, S.

1988-01-01

The opportunities and problems which in-situ leach mining technology presents to the mining industry are considered. These are exemplified by concerns addressed in the development of a proposal to mine uranium by in-situ leach techniques at Beverley in South Australia. The technique proposed at Beverley will use sulphuric acid with hydrogen peroxide or dissolved oxygen as the lixivient. Pre-treatment of the aquifer will be necessary to remove excess calcium carbonate, and the system will employ a slightly overpumped output of fluid through the wellfield to reduce the risk of excursions of mining solutions. The input and output patterns will also be varied to take account of the hydrogeological conditions such as confining bed thickness and permeability. Much study has been directed towards the post mining condition of the ore zone and the threat it may pose to the water resources of the region. 10 refs., 1 fig

Effect of Winter Cover Crops on Soil Nitrogen Availability, Corn Yield, and Nitrate Leaching

Directory of Open Access Journals (Sweden)

S. Kuo

2001-01-01

Full Text Available Biculture of nonlegumes and legumes could serve as cover crops for increasing main crop yield, while reducing NO3 leaching. This study, conducted from 1994 to 1999, determined the effect of monocultured cereal rye (Secale cereale L., annual ryegrass (Lolium multiflorum, and hairy vetch (Vicia villosa, and bicultured rye/vetch and ryegrass/vetch on N availability in soil, corn (Zea mays L. yield, and NO3-N leaching in a silt loam soil. The field had been in corn and cover crop rotation since 1987. In addition to the cover crop treatments, there were four N fertilizer rates (0, 67, 134, and 201 kg N ha-1, referred to as N0, N1, N2, and N3, respectively applied to corn. The experiment was a randomized split-block design with three replications for each treatment. Lysimeters were installed in 1987 at 0.75 m below the soil surface for leachate collection for the N0, N2, and N3 treatments. The result showed that vetch monoculture had the most influence on soil N availability and corn yield, followed by the bicultures. Rye or ryegrass monoculture had either no effect or an adverse effect on corn yield and soil N availability. Leachate NO3-N concentration was highest where vetch cover crop was planted regardless of N rates, which suggests that N mineralization of vetch N continued well into the fall and winter. Leachate NO3-N concentration increased with increasing N fertilizer rates and exceeded the U.S. Environmental Protection Agency’s drinking water standard of 10 mg N l�1 even at recommended N rate for corn in this region (coastal Pacific Northwest. In comparisons of the average NO3-N concentration during the period of high N leaching, monocultured rye and ryegrass or bicultured rye/vetch and ryegrass/vetch very effectively decreased N leaching in 1998 with dry fall weather. The amount of N available for leaching (determined based on the presidedress nitrate test, the amount of N fertilizer applied, and N uptake correlated well with average NO3

Effect of winter cover crops on soil nitrogen availability, corn yield, and nitrate leaching.

Science.gov (United States)

Kuo, S; Huang, B; Bembenek, R

2001-10-25

Biculture of nonlegumes and legumes could serve as cover crops for increasing main crop yield, while reducing NO3 leaching. This study, conducted from 1994 to 1999, determined the effect of monocultured cereal rye (Secale cereale L.), annual ryegrass (Lolium multiflorum), and hairy vetch (Vicia villosa), and bicultured rye/vetch and ryegrass/vetch on N availability in soil, corn (Zea mays L.) yield, and NO3-N leaching in a silt loam soil. The field had been in corn and cover crop rotation since 1987. In addition to the cover crop treatments, there were four N fertilizer rates (0, 67, 134, and 201 kg N ha(-1), referred to as N0, N1, N2, and N3, respectively) applied to corn. The experiment was a randomized split-block design with three replications for each treatment. Lysimeters were installed in 1987 at 0.75 m below the soil surface for leachate collection for the N 0, N 2, and N 3 treatments. The result showed that vetch monoculture had the most influence on soil N availability and corn yield, followed by the bicultures. Rye or ryegrass monoculture had either no effect or an adverse effect on corn yield and soil N availability. Leachate NO3-N concentration was highest where vetch cover crop was planted regardless of N rates, which suggests that N mineralization of vetch N continued well into the fall and winter. Leachate NO3-N concentration increased with increasing N fertilizer rates and exceeded the U.S. Environmental Protection Agency's drinking water standard of 10 mg N l(-1) even at recommended N rate for corn in this region (coastal Pacific Northwest). In comparisons of the average NO3-N concentration during the period of high N leaching, monocultured rye and ryegrass or bicultured rye/vetch and ryegrass/vetch very effectively decreased N leaching in 1998 with dry fall weather. The amount of N available for leaching (determined based on the presidedress nitrate test, the amount of N fertilizer applied, and N uptake) correlated well with average NO3-N during

COPPER LEACHING FROM WASTE ELECTRIC CABLES BY BIOHYDROMETALLURGY

OpenAIRE

Lambert, Fanny; Bastin, David; Gaydardzhiev, Stoyan; Léonard, Grégoire

2015-01-01

This study examines the leaching of copper from waste electric cables by chemical leaching and leaching catalysed by Acidithiobacillus ferrooxidans in terms of leaching kinetics and reagents consumption. Operational parameters such as the nature of the oxidant (Fe3+, O2), the initial ferric iron concentration (0-10 g/L) and the temperature (21-50°C) were identified to have an important influence on the degree of copper solubilisation. At optimal process conditions, copper extraction above 90%...

Column leaching from biomass combustion ashes

DEFF Research Database (Denmark)

Maresca, Alberto; Astrup, Thomas Fruergaard

2015-01-01

The utilization of biomass combustion ashes for forest soil liming and fertilizing has been addressed in literature. Though, a deep understanding of the ash chemical composition and leaching behavior is necessary to predict potential benefits and environmental risks related to this practice....... In this study, a fly ash sample from an operating Danish power plant based on wood biomass was collected, chemically characterized and investigated for its leaching release of nutrients and heavy metals. A column leaching test was employed. The strongly alkaline pH of all the collected eluates suggested...

Summarizing of new techniques in uranium mining and metallurgy

International Nuclear Information System (INIS)

Wang Delin; Zhang Fei; Su Yanru; Zeng Yijun; Meng Jin

2010-01-01

According to character of national resources and uranium mining and metallurgical science and technology members research achievements, new techniques in ten scientific research area of in-situ leaching, heap leaching, multi-metal comprehensive recovery, bio-metallurgy etc. for 10 years is introduced in this paper. The level of innovation ability is shown by technical index, resources recovery and reduction capital cost etc. datum. The application bound of natural uranium resource is enlarged and production ability of national uranium is increased. It is put forward renovation and development ideas for uranium mining and metallurgy. (authors)

Long-term Effects of Organic Waste Fertilizers on Soil Structure, Tracer Transport, and Leaching of Colloids.

Science.gov (United States)

Lekfeldt, Jonas Duus Stevens; Kjaergaard, Charlotte; Magid, Jakob

2017-07-01

Organic waste fertilizers have previously been observed to significantly affect soil organic carbon (SOC) content and soil structure. However, the effect of organic waste fertilizers on colloid dispersibility and leaching of colloids from topsoil has not yet been studied extensively. We investigated how the repeated application of different types of agricultural (liquid cattle slurry and solid cattle manure) and urban waste fertilizers (sewage sludge and composted organic household waste) affected soil physical properties, colloid dispersion from aggregates, tracer transport, and colloid leaching from intact soil cores. Total porosity was positively correlated with SOC content. Yearly applications of sewage sludge increased absolute microporosity (pores 30 μm) compared with the unfertilized control, whereas organic household waste compost fertilization increased both total porosity and the absolute porosity in all pore size classes (though not significant for 100-600 μm). Treatments receiving large amounts of organic fertilizers exhibited significantly lower levels of dispersible colloids compared with an unfertilized control and a treatment that had received moderate applications of cattle slurry. The content of water-dispersible colloids could not be explained by a single factor, but differences in SOC content, electrical conductivity, and sodium adsorption ratio were important factors. Moreover, we found that the fertilizer treatments did not significantly affect the solute transport properties of the topsoil. Finally, we found that the leaching of soil colloids was significantly decreased in treatments that had received large amounts of organic waste fertilizers, and we ascribe this primarily to treatment-induced differences in effluent electrical conductivity during leaching. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Radiocesium leaching from contaminated litter in forest streams

International Nuclear Information System (INIS)

Sakai, Masaru; Gomi, Takashi; Naito, Risa S.; Negishi, Junjiro N.; Sasaki, Michiko; Toda, Hiroto; Nunokawa, Masanori; Murase, Kaori

2015-01-01

In Japanese forests suffering from the Fukushima Daiichi Nuclear Power Plant accident, litter fall provides a large amount of radiocesium from forests to streams. Submerged litter is processed to become a vital food resource for various stream organisms through initial leaching and subsequent decomposition. Although leaching from litter can detach radiocesium similarly to potassium, radiocesium leaching and its migration are poorly understood. We examined both radiocesium and potassium leaching to the water column and radiocesium allocation to minerals (glass beads, silica sand, and vermiculite) in the laboratory using soaked litter with and without minerals on a water column. The mineral types did not affect radiocesium leaching from litter, but soaking in water for 1, 7, and 30 days decreased the radiocesium concentration in litter by ×0.71, ×0.66, and ×0.56, respectively. Meanwhile, the 1-, 7-, and 30-day experiments decreased potassium concentration in litter by ×0.17, ×0.11, and ×0.09, respectively. Leached radiocesium remained in a dissolved form when there was no mineral phases present in the water, whereas there was sorption onto the minerals when they were present. In particular, vermiculite adsorbed radiocesium by two to three orders of magnitude more effectively than the other minerals. Because radiocesium forms (such as that dissolved or adsorbed to organic matter or minerals) can further mobilize to ecosystems, our findings will increase our understanding regarding the dynamics of radiocesium in stream ecosystems. - Highlights: • Radiocesium in contaminated litter was leached when soaked in water. • Radiocesium in litter leached slowly compared to potassium. • Minerals adsorbed dissolved radiocesium that was leached from litter. • Vermiculite effectively adsorbed radiocesium leached from litter

Impact of mining on suspended materials in the Mandovi and Zuari ...

Indian Academy of Sciences (India)

At the regular station -- SPM is controlled by River run off, resuspension and interaction of freshwater- seawater. -- SPM at high salinity is mixture of land- derived (kaolinite) and resuspended (smectite) material. -- High Fe, Mn and Co in SPM are derived from the leaching of Fe-Mn ores heaped along the shore during heavy ...

Uranium mining and milling by Cogema environmental impact compared to 1 mSv limit

International Nuclear Information System (INIS)

Bernhard, S.; Daroussin, J.L.; Pfiffelmann, J.P.

1996-01-01

CEA then COGEMA have been operating mines and mills in France since 1948. Total production nears 70000 t of U in the concentrate which were contained in some 85 millions tons of ores (pulp and heap leaching). Many sites are now undergoing remediation and impact on the environment has always been a great concern. (author)

Demonstration of the efficiency and robustness of an acid leaching process to remove metals from various CCA-treated wood samples.

Science.gov (United States)

Coudert, Lucie; Blais, Jean-François; Mercier, Guy; Cooper, Paul; Janin, Amélie; Gastonguay, Louis

2014-01-01

In recent years, an efficient and economically attractive leaching process has been developed to remove metals from copper-based treated wood wastes. This study explored the applicability of this leaching process using chromated copper arsenate (CCA) treated wood samples with different initial metal loading and elapsed time between wood preservation treatment and remediation. The sulfuric acid leaching process resulted in the solubilization of more than 87% of the As, 70% of the Cr, and 76% of the Cu from CCA-chips and in the solubilization of more than 96% of the As, 78% of the Cr and 91% of the Cu from CCA-sawdust. The results showed that the performance of this leaching process might be influenced by the initial metal loading of the treated wood wastes and the elapsed time between preservation treatment and remediation. The effluents generated during the leaching steps were treated by precipitation-coagulation to satisfy the regulations for effluent discharge in municipal sewers. Precipitation using ferric chloride and sodium hydroxide was highly efficient, removing more than 99% of the As, Cr, and Cu. It appears that this leaching process can be successfully applied to remove metals from different CCA-treated wood samples and then from the effluents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Recycling of spent lithium-ion battery cathode materials by ammoniacal leaching

International Nuclear Information System (INIS)

Ku, Heesuk; Jung, Yeojin; Jo, Minsang; Park, Sanghyuk; Kim, Sookyung; Yang, Donghyo; Rhee, Kangin; An, Eung-Mo; Sohn, Jeongsoo; Kwon, Kyungjung

2016-01-01

Highlights: • Ammoniacal leaching is used to recover spent Li-ion battery cathode materials. • Leaching agents consist of ammonia, ammonium sulfite and ammonium carbonate. • Ammonium sulfite is a reductant and ammonium carbonate acts as pH buffer. • Co and Cu can be fully leached while Mn and Al are not leached. • Co recovery via ammoniacal leaching is economical compared to acid leaching. - Abstract: As the production and consumption of lithium ion batteries (LIBs) increase, the recycling of spent LIBs appears inevitable from an environmental, economic and health viewpoint. The leaching behavior of Ni, Mn, Co, Al and Cu from treated cathode active materials, which are separated from a commercial LIB pack in hybrid electric vehicles, is investigated with ammoniacal leaching agents based on ammonia, ammonium carbonate and ammonium sulfite. Ammonium sulfite as a reductant is necessary to enhance leaching kinetics particularly in the ammoniacal leaching of Ni and Co. Ammonium carbonate can act as a pH buffer so that the pH of leaching solution changes little during leaching. Co and Cu can be fully leached out whereas Mn and Al are hardly leached and Ni shows a moderate leaching efficiency. It is confirmed that the cathode active materials are a composite of LiMn_2O_4, LiCo_xMn_yNi_zO_2_, Al_2O_3 and C while the leach residue is composed of LiNi_xMn_yCo_zO_2, LiMn_2O_4, Al_2O_3, MnCO_3 and Mn oxides. Co recovery via the ammoniacal leaching is believed to gain a competitive edge on convenitonal acid leaching both by reducing the sodium hydroxide expense for increasing the pH of leaching solution and by removing the separation steps of Mn and Al.

Leaching of heavy metals from steelmaking slags

International Nuclear Information System (INIS)

Gomez, J. F. P.; Pino, C. G.

2006-01-01

Leaching tests with EAF and Ladle slags were performed, using a flow through tests and the standard batch test DIN 38414-S4. The previous method was used to simulate the leaching behaviour of steel slags under landfill. the chemical analysis of the leachates during this period shows, in general, for both types of slag, and increase of heavy metal releases with ageing. Standard test method DIN 38414-S4 was used to evaluate leachability of heavy metals by water in unprocessed slags. After more than one year of trials, slang samples submitted to these trials presented very low total leaching levels. The most extracted elements are calcium and magnesium. Nevertheless, in flow-though test, calcium and magnesium leached from solid slags are below 0.5% and all other metals below 0.1%. Leachates obtained with DIN 38414-S4 present, as expected, higher leaching values; however, these are inferior to 5% (Ca) and 1% (other elements). (Author) 12 refs

Development of an accelerated leaching method for incineration bottom ash correlated to toxicity characteristic leaching protocol.

Science.gov (United States)

Lin, Shengxuan; Zhou, Xuedong; Ge, Liya; Ng, Sum Huan; Zhou, Xiaodong; Chang, Victor Wei-Chung

2016-10-01

Heavy metals and some metalloids are the most significant inorganic contaminants specified in toxicity characteristic leaching procedure (TCLP) in determining the safety of landfills or further utilization. As a consequence, a great deal of efforts had been made on the development of miniaturized analytical devices, such as Microchip Electrophoresis (ME) and μTAS for on-site testing of heavy metals and metalloids to prevent spreading of those pollutants or decrease the reutilization period of waste materials such as incineration bottom ash. However, the bottleneck lied in the long and tedious conventional TCLP that requires 18 h of leaching. Without accelerating the TCLP process, the on-site testing of the waste material leachates was impossible. In this study, therefore, a new accelerated leaching method (ALM) combining ultrasonic assisted leaching with tumbling was developed to reduce the total leaching time from 18 h to 30 min. After leaching, the concentrations of heavy metals and metalloids were determined with ICP-MS or ICP-optical emission spectroscopy. No statistical significance between ALM and TCLP was observed for most heavy metals (i.e., cobalt, manganese, mercury, molybdenum, nickel, silver, strontium, and tin) and metalloids (i.e., arsenic and selenium). For the heavy metals with statistical significance, correlation factors derived between ALM and TCLP were 0.56, 0.20, 0.037, and 0.019 for barium, cadmium, chromium, and lead, respectively. Combined with appropriate analytical techniques (e.g., ME), the ALM can be applied to rapidly prepare the incineration bottom ash samples as well as other environmental samples for on-site determination of heavy metals and metalloids. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stability and leaching of cobalt smelter fly ash

DEFF Research Database (Denmark)

Vítková, Martina; Hyks, Jiri; Ettler, Vojtěch

2013-01-01

The leaching behaviour of fly ash from a Co smelter situated in the Zambian Copperbelt was studied as a function of pH (5–12) using the pH-static leaching test (CEN/TS 14997). Various experimental time intervals (48h and 168h) were evaluated. The leaching results were combined with the ORCHESTRA...... modelling framework and a detailed mineralogical investigation was performed on the original FA and leached solid residues. The largest amounts of Co, Cu, Pb and Zn were leached at pH 5, generally with the lowest concentrations between pH 9 and 11 and slightly increased concentrations at pH 12. For most...... detected using SEM/EDS and/or TEM/EDS. The leaching of metals was mainly attributed to the dissolution of metallic particles. Partial dissolution of silicate and glass fractions was assumed to significantly influence the release of Ca, Mg, Fe, K, Al and Si as well as Cu, Co and Zn. The formation of illite...

Recovery of Vanadium from Magnetite Ore Using Direct Acid Leaching: Optimization of Parameters by Plackett-Burman and Response Surface Methodologies

Science.gov (United States)

Nejad, Davood Ghoddocy; Khanchi, Ali Reza; Taghizadeh, Majid

2018-06-01

Recovery of vanadium from magnetite ore by direct acid leaching is discussed. The proposed process, which employs a mixture of nitric and sulfuric acids, avoids pyrometallurgical treatments since such treatment consumes a high amount of energy. To determine the optimum conditions of vanadium recovery, the leaching process is optimized through Plackett-Burman (P-B) design and response surface methodology (RSM). In this respect, temperature (80-95°C), liquid to solid ratio (L/S) (3-10 mL g-1), sulfuric acid concentration (3-6 M), nitric acid concentration (5-10 vol.%) and time (4-8 h) are considered as the independent variables. According to the P-B approach, temperature and acid concentrations are, respectively, the most effective parameters in the leaching process. These parameters are optimized using RSM to maximize recovery of vanadium by direct acid leaching. In this way, 86.7% of vanadium can be extracted from magnetic ore.

Microbiological metal extraction processes

International Nuclear Information System (INIS)

Torma, A.E.

1991-01-01

Application of biotechnological principles in the mineral processing, especially in hydrometallurgy, has created new opportunities and challenges for these industries. During the 1950's and 60's, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes for copper and uranium. The interest in bio-leaching processes is the consequence of economic advantages associated with these techniques. For example, copper can be produced from mining wastes for about 1/3 to 1/2 of the costs of copper production by the conventional smelting process from high-grade sulfide concentrates. The economic viability of bio leaching technology lead to its world wide acceptance by the extractive industries. During 1970's this technology grew into a more structured discipline called 'bio hydrometallurgy'. Currently, bio leaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, precious metals and for the desulfurization of high-sulfur content pyritic coals. As a developing technology, the microbiological leaching of the less common and rare metals has yet to reach commercial maturity. However, the research in this area is very active. In addition, in a foreseeable future the biotechnological methods may be applied also for the treatment of high-grade ores and mineral concentrates using adapted native and/or genetically engineered microorganisms. (author)

Leaching of potassium in a lysimeter experiment

International Nuclear Information System (INIS)

Gerzabek, M.H.

1996-11-01

Leaching of potassium was studied in the lysimeter plant in Seibersdorf/Austria (Pannonian climate). Averaged over three years, gravitational water amounted to 15.7% of the sum of precipitation (mean 485 mm) and irrigation (mean 138 mm). Differences between the four soils with respect to drainage were explained by the specific percentage of the soil skeleton. The average yearly potassium leaching ranged from 3.64 kg K/ha·yr (Dystric-Cambisol) to 22.7 kg K/ha·yr (drained Gleysol). Correlation between gravitational water volume and potassium leaching were only significant for one out of four soil types. No correlation was observed between extractable potassium in the soil profiles and potassium leaching. (author)

Recovery of Iron from Pyrolusite Leaching Slag by a Lab-Scale Circulation Process of Oxalic Acid Leaching and Ultraviolet Irradiation

Directory of Open Access Journals (Sweden)

Biao Deng

2017-12-01

Full Text Available Pyrolusite leaching slag is a Fe-containing slag generated from pyrolusite leaching process with SO2. Recovery of iron from the slag not only has economic benefit, but also prevents the secondary pollution to the environment. A novel lab-scale cyclic process for recovering iron from pyrolusite leaching slag was introduced. The process contains two steps: (1 iron was leached with oxalic acid and [Fe(C2O4n](3−2n+ solution was generated; (2 the [Fe(C2O4n](3−2n+ solution was irradiated by ultraviolet and ferrous oxalate precipitation were obtained. The effect of operation parameter on leaching and irradiation process were studied separately. In the leaching process, the optimal solid/liquid ratio, oxalic acid concentration, leaching temperature, stirring rate, and leaching time are 1:50, 0.40 mol/L, 95 °C, 300 r/min, and 3 h, respectively. In the irradiation process, the best irradiation wavelength, Fe/oxalic acid molar ratio and irradiation time are 254 nm, 1:4, and 30 min. Besides, a test of 9 continuous cycles was carried out and the performance and material balance of the combined process were investigated. The results showed that the cyclic process is entirely feasible and prove to be stable producing, and ferrous oxalate of 99.32% purity. Material balance indicated that 95.17% of iron was recovered in the form of FeC2O4·2H2O, and the recovery efficiency of oxalic acid was 58.52%.

Experiment on bio-leaching of associated molybdenum and uranium ore

International Nuclear Information System (INIS)

Zheng Ying; Fan Baotuan; Liu Jian; Meng Yunsheng; Liu Chao

2007-01-01

Column leaching experiment results on associated molybdenum uranium ore by bacteria (T. f) are introduced. The ore are leached for 210 days using bacteria domesticated to tolerate molybdenum, the leaching of uranium is of 98% and leaching of molybdenum is of 41%. Sulphuric acid produced by bio-oxidation of sulfides in ore can meet the demand of ore leaching. (authors)

Impact of simulated acid rain on trace metals and aluminum leaching in latosol from Guangdong Province, China

Science.gov (United States)

Jia-En Zhang; Jiayu Yu; Ying Ouyang; Huaqin. Xu

2014-01-01

Acid rain is one of the most serious ecological and environmental problems worldwide. This study investigated the impacts of simulated acid rain (SAR) upon leaching of trace metals and aluminum (Al) from a soil. Soil pot leaching experiments were performed to investigate the impacts of SAR at five different pH levels (or treatments) over a 34-day period upon the...

ESCA studies on leached glass forms

International Nuclear Information System (INIS)

Dawkins, B.G.

1979-01-01

Electron Spectroscopy for Chemical Analysis (ESCA) results for frit, obsidian, NBS standard, and Savannah River Laboratory (SRL) glass forms that have been subjected to cumulative water leachings of 36 hours show that [Na] exhibits the largest and fastest change of all the elements observed. Leaching of surface Na occurred within minutes. Surface Na depletion increased with leach time. Continuous x-ray irradiation and argon ion milling induced Na mobility, precluding semiquantitative ESCA analysis at normal operating temperatures. However, the sample stage has been equipped with a liquid nitrogen supply and alkali mobility should be eliminated in future work

Leaching and sorption of neonicotinoid insecticides and fungicides from seed coatings

Science.gov (United States)

Smalling, Kelly; Hladik, Michelle; Sanders, Corey; Kuivila, Kathryn

2018-01-01

Seed coatings are a treatment used on a variety of crops to improve production and offer protection against pests and fungal outbreaks. The leaching of the active ingredients associated with the seed coatings and the sorption to soil was evaluated under laboratory conditions using commercially available corn and soybean seeds to study the fate and transport of these pesticides under controlled conditions. The active ingredients (AI) included one neonicotinoid insecticide (thiamethoxam) and five fungicides (azoxystrobin, fludioxonil, metalaxyl, sedaxane thiabendazole). An aqueous leaching experiment was conducted with treated corn and soybean seeds. Leaching potential was a function of solubility and seed type. The leaching of fludioxonil, was dependent on seed type with a shorter time to equilibrium on the corn compared to the soybean seeds. Sorption experiments with the treated seeds and a solution of the AIs were conducted using three different soil types. Sorption behavior was a function of soil organic matter as well as seed type. For most AIs, a negative relationship was observed between the aqueous concentration and the log Koc. Sorption to all soils tested was limited for the hydrophilic pesticides thiamethoxam and metalaxyl. However, partitioning for the more hydrophobic fungicides was dependent on both seed type and soil properties. The mobility of fludioxonil in the sorption experiment varied by seed type indicating that the adjuvants associated with the seed coating could potentially play a role in the environmental fate of fludioxonil. This is the first study to assess, under laboratory conditions, the fate of pesticides associated with seed coatings using commercially available treated seeds. This information can be used to understand how alterations in agricultural practices (e.g., increasing use of seed treatments) can impact the exposure (concentration and duration) and potential effects of these chemicals to aquatic and terrestrial organisms.

Spent LWR fuel leach tests: Waste Isolation Safety Assessment program

International Nuclear Information System (INIS)

Katayama, Y.B.

1979-04-01

Spent light-water-reactor (LWR) fuels with burnups of 54.5, 28 and 9 MWd/kgU were leach-tested in deionized water at 25 0 C. Fuel burnup has no apparent effect on the calculated leach rates based upon the behavior of 137 Cs and 239+240 Pu. A leach test of 54.5 MWd/kgU spent fuel in synthetic sea brine showed that the cesium-based leach rate is lower in sea brine than in deionized water. A rise in the leach rate was observed after approximately 600 d of cumulative leaching. During the rise, the leach rate for all the measured radionuclides become nearly equal. Evidence suggests that exposure of new surfaces to the leachant may cause the increase. As a result, experimental work to study leaching mechanisms of spent fuel has been initiated. 22 figures

YACON INULIN LEACHING DURING HOT WATER BLANCHING

Directory of Open Access Journals (Sweden)

Caroline Fenner Scher

2015-10-01

Full Text Available ABSTRACTYacon roots contain inulin, which has prebiotic properties and it may be used as sucrose or fat substitutes. However, inulin is very soluble in water. The loss of this important nutrient during blanching is caused mainly by diffusion or leaching, which might be diminished if blanching temperature - time conditions are correctly employed. The aim of this study was to determine the leaching of the sugars inulin, glucose and fructose, present in yacon roots, during hot water blanching under different time/temperature conditions. The samples were cleaned and peeled and cut into geometric forms of 1.75 ± 0.35 mm thick disks. A complete factorial experimental design was used, and the treatments of the samples were compared using the Tukey test. The results indicated that the time and temperature were significant in the dissolution of the sugars. The lowest inulin losses occurred at temperatures and times lower than 60 ºC and 3 minutes. For all temperatures, the lowest glucose and fructose losses were obtained at time lower than 3 and 5 minutes, respectively.

Impact of weather variability on nitrate leaching

Science.gov (United States)

Richards, Karl; Premrov, Alina; Hackett, Richard; Coxon, Catherine

2016-04-01

The loss of nitrate (NO3 - N) to water via leaching and overland flow contributes to eutrophication of freshwaters, transitional and near coastal waters with agriculture contributing significantly to nitrogen (N) loading to these water. Environmental regulations, such as the Nitrates and Water Framework Directives, have increased constraints on farmers to improve N management in regions at risk of NO3--N loss to water. In addition, farmers also have to manage their systems within a changing climate as the imapcts of climate change begin to impact resulting in more frequent extreme events such as floods and droughts. The objective of this study was to investigate the link between weather volatility and the concentration of leached NO3--N spring barley. Leaching was quantified under spring barley grown on a well-drained, gravelly sandy soil using ceramic cup samplers over 6 drainage years under the same farming practices and treatments. Soil solution NO3--N concentrations under spring barley grown by conventional inversion ploughing and reduced tillage were compared to weather parameters over the period. Weather was recorded at a national Met Eireann weather station on site. Soil solution NO3--N varied significantly between years. Within individual years NO3--N concentrations varied over the drainage season, with peak concentrations generally observed in the autumn time, decreasing thereafter. Under both treatments there was a three-fold difference in mean annual soil solution NO3--N concentration over the 6 years with no change in the agronomic practices (crop type, tillage type and fertiliser input). Soil solution nitrate concentrations were significantly influenced by weather parameters such as rainfall, effective drainage and soil moisture deficit. The impact of climate change in Ireland could lead to increased NO3--N loss to water further exacerbating eutrophication of sensitive estuaries. The increased impact on eutrophication of waters, related to climatic

Analysis of SPR salt cavern remedial leach program 2013.

Energy Technology Data Exchange (ETDEWEB)

Weber, Paula D.; Gutierrez, Karen A.; Lord, David L.; Rudeen, David Keith

2013-09-01

The storage caverns of the US Strategic Petroleum Reserve (SPR) exhibit creep behavior resulting in reduction of storage capacity over time. Maintenance of oil storage capacity requires periodic controlled leaching named remedial leach. The 30 MMB sale in summer 2011 provided space available to facilitate leaching operations. The objective of this report is to present the results and analyses of remedial leach activity at the SPR following the 2011 sale until mid-January 2013. This report focuses on caverns BH101, BH104, WH105 and WH106. Three of the four hanging strings were damaged resulting in deviations from normal leach patterns; however, the deviations did not affect the immediate geomechanical stability of the caverns. Significant leaching occurred in the toes of the caverns likely decreasing the number of available drawdowns until P/D ratio criteria are met. SANSMIC shows good agreement with sonar data and reasonably predicted the location and size of the enhanced leaching region resulting from string breakage.

Recycling of spent lithium-ion battery cathode materials by ammoniacal leaching

Energy Technology Data Exchange (ETDEWEB)

Ku, Heesuk; Jung, Yeojin; Jo, Minsang; Park, Sanghyuk [Department of Energy & Mineral Resources Engineering, Sejong University, Seoul 05006 (Korea, Republic of); Kim, Sookyung [Urban Mine Department, Korea Institute of Geoscience and Mineral Resources, 124 Gwahang-no, Yuseong-gu, Daejeon (Korea, Republic of); Yang, Donghyo, E-mail: ydh@kigam.re.kr [Urban Mine Department, Korea Institute of Geoscience and Mineral Resources, 124 Gwahang-no, Yuseong-gu, Daejeon (Korea, Republic of); Rhee, Kangin; An, Eung-Mo; Sohn, Jeongsoo [Urban Mine Department, Korea Institute of Geoscience and Mineral Resources, 124 Gwahang-no, Yuseong-gu, Daejeon (Korea, Republic of); Kwon, Kyungjung, E-mail: kfromberk@gmail.com [Department of Energy & Mineral Resources Engineering, Sejong University, Seoul 05006 (Korea, Republic of)

2016-08-05

Highlights: • Ammoniacal leaching is used to recover spent Li-ion battery cathode materials. • Leaching agents consist of ammonia, ammonium sulfite and ammonium carbonate. • Ammonium sulfite is a reductant and ammonium carbonate acts as pH buffer. • Co and Cu can be fully leached while Mn and Al are not leached. • Co recovery via ammoniacal leaching is economical compared to acid leaching. - Abstract: As the production and consumption of lithium ion batteries (LIBs) increase, the recycling of spent LIBs appears inevitable from an environmental, economic and health viewpoint. The leaching behavior of Ni, Mn, Co, Al and Cu from treated cathode active materials, which are separated from a commercial LIB pack in hybrid electric vehicles, is investigated with ammoniacal leaching agents based on ammonia, ammonium carbonate and ammonium sulfite. Ammonium sulfite as a reductant is necessary to enhance leaching kinetics particularly in the ammoniacal leaching of Ni and Co. Ammonium carbonate can act as a pH buffer so that the pH of leaching solution changes little during leaching. Co and Cu can be fully leached out whereas Mn and Al are hardly leached and Ni shows a moderate leaching efficiency. It is confirmed that the cathode active materials are a composite of LiMn{sub 2}O{sub 4}, LiCo{sub x}Mn{sub y}Ni{sub z}O{sub 2,} Al{sub 2}O{sub 3} and C while the leach residue is composed of LiNi{sub x}Mn{sub y}Co{sub z}O{sub 2}, LiMn{sub 2}O{sub 4}, Al{sub 2}O{sub 3}, MnCO{sub 3} and Mn oxides. Co recovery via the ammoniacal leaching is believed to gain a competitive edge on convenitonal acid leaching both by reducing the sodium hydroxide expense for increasing the pH of leaching solution and by removing the separation steps of Mn and Al.

Numerical simulation of vertical infiltration for leaching fluid in situ

International Nuclear Information System (INIS)

Li Jinxuan; Shi Weijun; Zhang Weimin

1998-01-01

Based on the analysis of movement law of leaching fluid in breaking and leaching experiment in situ, the movement of leaching fluid can be divided into two main stages in the leaching process in situ: Vertical Infiltration in unsaturation zone and horizontal runoff in saturation zone. The corresponding mathematics models are sep up, and the process of vertical infiltration of leaching fluid is numerically simulated

Salt and N leaching and soil accumulation due to cover cropping practices

Science.gov (United States)

Gabriel, J. L.; Quemada, M.

2012-04-01

Nitrate leaching beyond the root zone can increase water contamination hazards and decrease crop available N. Cover crops used in spite of fallow are an alternative to reduce nitrate contamination in the vadose zone, because reducing drainage and soil mineral N accumulation. Cover crops can improve important characteristics in irrigated land as water retention capacity or soil aggregate stability. However, increasing evapotranspiration and consequent drainage below the root system reduction, could lead to soil salt accumulation. Salinity affects more than 80 million ha of arable land in many areas of the world, and one of the principal causes for yield reduction and even land degradation in the Mediterranean region. Few studies dealt with both problems at the same time. Therefore, it is necessary a long-term evaluation of the potential effect on soil salinity and nitrate leaching, in order to ensure that potential disadvantages that could originate from soil salt accumulation are compensated with all advantages of cover cropping. A study of the soil salinity and nitrate leaching was conducted during 4 years in a semiarid irrigated agricultural area of Central Spain. Three treatments were studied during the intercropping period of maize (Zea mays L.): barley (Hordeum vulgare L.), vetch (Vicia villosa L.) and fallow. Cover crops were killed in March allowing seeding of maize of the entire trial in April, and all treatments were irrigated and fertilised following the same procedure. Before sowing, and after harvesting maize and cover crops, soil salt and nitrate accumulation was determined along the soil profile. Soil analysis was conducted at six depths every 0.20 m in each plot in samples from four 0 to 1.2-m depth holes dug. The electrical conductivity of the saturated paste extract and soil mineral nitrogen was measured in each soil sample. A numerical model based on the Richards water balance equation was applied in order to calculate drainage at 1.2 m depth

Uranium extraction from high content chlorine leach liquor

International Nuclear Information System (INIS)

Fatemi, K.

1998-01-01

In this work uranium solution has been leached out by leaching process of uranium ores from Bandar-Ab bass port using sea water, since fresh water could not be available when it is processed in large scale. Two samples of different batches containing 11 and 20 gr./lit chlorine underwent two stages of precipitation by lead nitrate. As the result of this treatment the chlorine removed and its final concentration reduced to 530 p.p.m. which is well below allowances. Then, the uranium of this recent dechlorinated solu ton has been extracted by T.B.P. Uranium in organic phase was stripped out into inorganic phase by sodium carbonate and precipitated in a form of yellow cake and converted to U3o8. The total recovery of U, was well above 90% and the purity of the conc. U was better than 94%. The lead used at the beginning of the process was recovered for next use

The effects of leaching and floatation on the ash fusion temperatures of three selected lignites

Energy Technology Data Exchange (ETDEWEB)

Feng-hai Li; Jie-jie Huang; Yi-tian Fang; Yang Wang [Chinese Academy of Sciences, Taiyuan (China). Institute of Coal Chemistry

2011-07-15

Experiments have been conducted with Huolinhe (HLH), Xiaolongtan (XLT), and Ethiopian (ET) lignites to investigate the effects of washing with water, acid-leaching, and floatation on their ash fusion temperatures (AFTs). The results show that the AFTs of XLT and ET are elevated by washing with water and floatation, but the AFT of HLH is decreased. The AFTs of all three lignites are increased markedly by acid leaching. A decrease in the total basic composition in ash increases its AFT, and vice versa. Changes in the mineral contents of the coals after treatment contribute to the variations in their AFTs. After washing with water, the lower AFT of HLH is brought about by the increases in the amounts of cordierite and anhydrite, whereas the higher AFT of XLT is caused by the decreases in the amounts of anhydrite and calcite. For the floatation treatment, the decrease of AFT for HLH is due to the reduction in the amount of kaolinite, but the elevation of AFT for XLT or ET is caused by the decrease in the amount of pyrite and the reductions in the amounts of gypsum and xanthoxenite, respectively. For the acid-leaching treatment, a decrease in the amount of pyrite and an increase in the amount of kaolinite result in increases in AFTs for HLH and XLT. Increases in the amounts of kaolinite and cristobalite in FET (ET after floatation), WET (ET after washing with water), and AET (ET after acid-leaching) lead to corresponding increases in the AFTs. 27 refs., 10 figs., 3 tabs.

Predicting fragmentation sizing profiles for different blasting patterns

International Nuclear Information System (INIS)

Sheikh, A.M.; Chung, S.H.

1987-01-01

This paper evaluates the efficiency of blasting in a large scale underground heap leaching operation. The prediction model is based on the dynamic tensile breaking strength of rock formation, the detonation characteristics of the explosives and the drill hole pattern. The modelling includes crack pattern development and fragmentation computation fitted by the Rosin-Rammler distribution equation

Environmental impacts of mining: monitoring, restoration and control

Energy Technology Data Exchange (ETDEWEB)

Sengupta, M.

1993-01-01

Contains 12 chapters with the following titles: mining and the environment; surface coal mining with reclamation; reclamation and revegetation of mined land; the acid mine drainage problem from coal mines; acid rock drainage and metal migration; hydrologic impact; erosion and sediment control; wetlands; blasting; mining subsidence; postmining land use; environmental effects of gold heap-leaching operations.

Information Management of Health and Safety at the Tarkwa Mine of ...

African Journals Online (AJOL)

The Tarkwa Mine (TM) of Goldfields Ghana Limited (GGL) undertakes open pit mining operations with gold recovery by heap leach technology. As a mine, it is susceptible to health and safety risks in its operations. In spite of health and safety policy and regulations put in place at the TM, there have been reported cases of ...

Filtration and Leach Testing for REDOX Sludge and S-Saltcake Actual Waste Sample Composites

Energy Technology Data Exchange (ETDEWEB)

Shimskey, Rick W.; Billing, Justin M.; Buck, Edgar C.; Daniel, Richard C.; Draper, Kathryn E.; Edwards, Matthew K.; Geeting, John GH; Hallen, Richard T.; Jenson, Evan D.; Kozelisky, Anne E.; MacFarlan, Paul J.; Peterson, Reid A.; Snow, Lanee A.; Swoboda, Robert G.

2009-02-20

A testing program evaluating actual tank waste was developed in response to Task 4 from the M-12 External Flowsheet Review Team (EFRT) issue response plan.( ) The test program was subdivided into logical increments. The bulk water-insoluble solid wastes that are anticipated to be delivered to the Waste Treatment and Immobilization Plant (WTP) were identified according to type such that the actual waste testing could be targeted to the relevant categories. Under test plan TP-RPP-WTP-467, eight broad waste groupings were defined. Samples available from the 222S archive were identified and obtained for testing. Under this test plan, a waste-testing program was implemented that included: • Homogenizing the archive samples by group as defined in the test plan • Characterizing the homogenized sample groups • Performing parametric leaching testing on each group for compounds of interest • Performing bench-top filtration/leaching tests in the hot cell for each group to simulate filtration and leaching activities if they occurred in the UFP2 vessel of the WTP Pretreatment Facility. This report focuses on filtration/leaching tests performed on two of the eight waste composite samples and follow-on parametric tests to support aluminum leaching results from those tests.

Leaching of TCIPP from furniture foam is rapid and substantial.

Science.gov (United States)

Stubbings, William A; Harrad, Stuart

2018-02-01

A series of laboratory experiments were conducted, in which waste furniture polyurethane foam samples containing tris (1-chloro-2-propyl) phosphate (TCIPP) were contacted with a range of leaching fluids, formulated to simulate the composition of landfill leachate. Leaching was examined under a number of different scenarios, such as: dissolved humic matter concentration, pH, and temperature, as well as the effect of agitation, and waste:leaching fluid contact duration. In addition to single batch (no replenishment of leaching fluid), serial batch (draining of leachate and replenishment with fresh leaching fluid at various time intervals) experiments were conducted. Leaching of TCIPP from PUF appears to be a first order process. Concentrations of TCIPP in leachate generated by the experiments in this study ranged from 13 mg L -1 to 130 mg L -1 . In serial batch leaching experiments, >95% of TCIPP was depleted from PUF after 168 h total contact with leaching fluid. Our experiments indicate leaching is potentially a very significant pathway of TCIPP emissions to the environment. Copyright © 2017. Published by Elsevier Ltd.

Comparison of oxidants in alkaline leaching of uranium ore

International Nuclear Information System (INIS)

Sreenivas, T.; Rajan, K.C.; Srinivas, K.; Anand Rao, K.; Manmadha Rao, M.; Venkatakrishnan, R.R.; Padmanabhan, N.P.H.

2007-01-01

The uranium minerals occurring in various ore deposits consists of predominantly uranous ion (U +4 ), necessitating use of an oxidant and other lixiviants for efficient dissolution during leaching. Unlike acid leaching route, where uranium minerals dissolution could be achieved efficiently with cheaper lixiviants, processing of ores by alkaline leaching route involve expensive lixiviants and drastic leaching conditions. Alkaline leaching of uranium ores becomes economical only upon using cheaper and efficient oxidants and conservation of other reagents by their recycle. The present paper gives efficacy of various oxidants - KMnO 4 , NaOCl, Cu - NH 3 , air and oxygen, in the leaching of uranium from a low-grade dolostone hosted uranium ore of India. A comparison based on technical merits and cost of the oxidant chemicals is discussed. (author)

Leach behavior of hydrofracture grout incorporating radioactive wastes

International Nuclear Information System (INIS)

Moore, J.G.; Godbee, H.W.; Kibbey, A.H.

1976-01-01

Rates at which Sr, Cs, Pu, and Cm are leached from hydrofracture grout were measured. The fraction of an isotope leached varied with the square root of time if the leachant was replaced more frequently than once per day, but was inhibited or depressed if replacement was made less often. The amount of Sr or Cs leached from the grout varied directly with the degree of drying during curing and inversely with the time of curing. Of the clay additives studied for enhancing cesium retention, Grundite, while satisfactory, was the least effective. In general, the isotope leach rate followed the order: Cs greater than Sr greater than Cm greater than Pu. The amount leached as a function of the leachant varied in the order: distilled water greater than tap water greater than grout water. Concentrating the waste by a factor of up to 4 before grouting had little effect on the leach rate. Comparison with results for other products indicates that the grout can provide leach rates comparable to those for wastes incorporated into borosilicate glass. Theoretical relationships that consider diffusion and instantaneous reaction (an equilibrium or time-dependent relationship between mobile and immobile forms of a species) were in good agreement with the data for the 28-day-cured grout when the leachant was initially replaced twice per day. The credibility of laboratory results with simulated waste was substantiated by a short-term continuous leach test made on a fragment of a core sample of actual hydrofracture grout. The modified effective diffusivities (10 -11 to 10 -10 cm 2 /s, equivalent to a leach rate of the order of 10 -7 g cm -2 day -1 ) for Sr and Cs calculated from these data are comparable to laboratory values. 17 figures, 5 tables

Pilot test of bacterial percolation leaching at Fuzhou uranium mine

International Nuclear Information System (INIS)

Fan Baotuan; Liu Jian; Jiang Yngqiong; Cai Chunhui; Jiang Lang; Zhou Renhua; Tong Changning; Zhang Hongli

2006-01-01

Total 18 t uranium ores of Fuzhou Uranium Mine packed in three or four columns in series were leached by bacterial percolation. The results show that without adding any other chemical oxidant such as sodium chlorate, the leaching rate measured by residue is 91.45%-94.48%, leaching time is 50-60 d, acid consumption is 6.17%-7.75%, and residue grade is 0.0149%-0.0208%. Compared with conventional percolation leaching process, the leaching rate is improved by 3%, leaching time is shorted by 26%, and acid consumption is saved by 34%. Accumulation pattern of ΣFe and F - in the process of leaching is discussed. Influence of F - on bacterial growth, regeneration of barren solution as well as correlative techniques are reviewed. (authors)

Leaching of DOC, DN, and inorganic constituents from scrap tires.

Science.gov (United States)

Selbes, Meric; Yilmaz, Ozge; Khan, Abdul A; Karanfil, Tanju

2015-11-01

One concern for recycle and reuse of scrap tires is the leaching of tire constituents (organic and inorganic) with time, and their subsequent potential harmful impacts in environment. The main objective of this study was to examine the leaching of dissolved organic carbon (DOC), dissolved nitrogen (DN), and selected inorganic constituents from scrap tires. Different sizes of tire chips and crumb rubber were exposed to leaching solutions with pH's ranging from 3.0 to 10.0 for 28days. The leaching of DOC and DN were found to be higher for smaller size tire chips; however, the leaching of inorganic constituents was independent of the size. In general, basic pH conditions increased the leaching of DOC and DN, whereas acidic pH conditions led to elevated concentrations of metals. Leaching was minimal around the neutral pH values for all the monitored parameters. Analysis of the leaching rates showed that components associated with the rubbery portion of the tires (DOC, DN, zinc, calcium, magnesium, etc.) exhibited an initial rapid followed by a slow release. On the other hand, a constant rate of leaching was observed for iron and manganese, which are attributed to the metal wires present inside the tires. Although the total amounts that leached varied, the observed leaching rates were similar for all tire chip sizes and leaching solutions. Operation under neutral pH conditions, use of larger size tire chips, prewashing of tires, and removal of metal wires prior to application will reduce the impact of tire recycle and reuse. Copyright © 2015 Elsevier Ltd. All rights reserved.

Pollution potential leaching index as a tool to assess water leaching risk of arsenic in excavated urban soils.

Science.gov (United States)

Li, Jining; Kosugi, Tomoya; Riya, Shohei; Hashimoto, Yohey; Hou, Hong; Terada, Akihiko; Hosomi, Masaaki

2018-01-01

Leaching of hazardous trace elements from excavated urban soils during construction of cities has received considerable attention in recent years in Japan. A new concept, the pollution potential leaching index (PPLI), was applied to assess the risk of arsenic (As) leaching from excavated soils. Sequential leaching tests (SLT) with two liquid-to-solid (L/S) ratios (10 and 20Lkg -1 ) were conducted to determine the PPLI values, which represent the critical cumulative L/S ratios at which the average As concentrations in the cumulative leachates are reduced to critical values (10 or 5µgL -1 ). Two models (a logarithmic function model and an empirical two-site first-order leaching model) were compared to estimate the PPLI values. The fractionations of As before and after SLT were extracted according to a five-step sequential extraction procedure. Ten alkaline excavated soils were obtained from different construction projects in Japan. Although their total As contents were low (from 6.75 to 79.4mgkg -1 ), the As leaching was not negligible. Different L/S ratios at each step of the SLT had little influence on the cumulative As release or PPLI values. Experimentally determined PPLI values were in agreement with those from model estimations. A five-step SLT with an L/S of 10Lkg -1 at each step, combined with a logarithmic function fitting was suggested for the easy estimation of PPLI. Results of the sequential extraction procedure showed that large portions of more labile As fractions (non-specifically and specifically sorbed fractions) were removed during long-term leaching and so were small, but non-negligible, portions of strongly bound As fractions. Copyright © 2017 Elsevier Inc. All rights reserved.

Roasting and leaching behaviors of vanadium and chromium in calcification roasting-acid leaching of high-chromium vanadium slag

Science.gov (United States)

Wen, Jing; Jiang, Tao; Zhou, Mi; Gao, Hui-yang; Liu, Jia-yi; Xue, Xiang-xin

2018-05-01

Calcification roasting-acid leaching of high-chromium vanadium slag (HCVS) was conducted to elucidate the roasting and leaching behaviors of vanadium and chromium. The effects of the purity of CaO, molar ratio between CaO and V2O5 ( n(CaO)/ n(V2O5)), roasting temperature, holding time, and the heating rate used in the oxidation-calcification processes were investigated. The roasting process and mechanism were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetry-differential scanning calorimetry (TG-DSC). The results show that most of vanadium reacted with CaO to generate calcium vanadates and transferred into the leaching liquid, whereas almost all of the chromium remained in the leaching residue in the form of (Fe0.6Cr0.4)2O3. Variation trends of the vanadium and chromium leaching ratios were always opposite because of the competitive reactions of oxidation and calcification between vanadium and chromium with CaO. Moreover, CaO was more likely to combine with vanadium, as further confirmed by thermodynamic analysis. When the HCVS with CaO added in an n(CaO)/ n(V2O5) ratio of 0.5 was roasted in an air atmosphere at a heating rate of 10°C/min from room temperature to 950°C and maintained at this temperature for 60 min, the leaching ratios of vanadium and chromium reached 91.14% and 0.49%, respectively; thus, efficient extraction of vanadium from HCVS was achieved and the leaching residue could be used as a new raw material for the extraction of chromium. Furthermore, the oxidation and calcification reactions of the spinel phases occurred at 592 and 630°C for n(CaO)/ n(V2O5) ratios of 0.5 and 5, respectively.

Metal removal from Municipal Solid Waste Incineration fly ash: A comparison between chemical leaching and bioleaching.

Science.gov (United States)

Funari, V; Mäkinen, J; Salminen, J; Braga, R; Dinelli, E; Revitzer, H

2017-02-01